Thermally evaporated methylammonium tin triiodide thin films for lead-free perovskite solar cell fabrication

DOE PAGES

Yu, Yue; Zhao, Dewei; Grice, Corey R.; ...

2016-09-16

Here, we report on the synthesis of methylammonium tin triiodide (MASnI 3) thin films at room temperature by a hybrid thermal evaporation method and their application in fabricating lead (Pb)-free perovskite solar cells. The as-deposited MASnI 3 thin films exhibit smooth surfaces, uniform coverage across the entire substrate, and strong crystallographic preferred orientation along the < 100 > direction. By incorporating this film with an inverted planar device architecture, our Pb-free perovskite solar cells are able to achieve an open-circuit voltage ( V oc) up to 494 mV. The relatively high V oc is mainly ascribed to the excellent surfacemore » coverage, the compact morphology, the good stoichiometry control of the MASnI 3 thin films, and the effective passivation of the electron-blocking and hole-blocking layers. Finally, our results demonstrate the potential capability of the hybrid evaporation method to prepare high-quality Pb-free MASnI 3 perovskite thin films which can be used to fabricate efficient Pb-free perovskite solar cells.« less

Rapid pH change due to bacteriorhodopsin measured with a tin-oxide electrode.

PubMed Central

Robertson, B; Lukashev, E P

1995-01-01

The photocurrent transient generated by bacteriorhodopsin (bR) on a tin-oxide electrode is due to pH change and not to charge displacement as previously assumed. Films of either randomly oriented or highly oriented purple membranes were deposited on transparent electrodes made of tin-oxide-coated glass. The membranes contained either wild-type or D96N-mutant bR. When excited with yellow light through the glass, the bR pumps protons across the membrane. The result is a rapid local pH change as well as a charge displacement. Experiments with these films show that it is the pH change rather than the displacement that produces the current transient. The calibration for the transient pH measurement is given. The sensitivity of a tin-oxide electrode to a transient pH change is very much larger than its sensitivity to a steady-state pH change. PMID:7787036

Tin-silver-bismuth solders for electronics assembly

DOEpatents

Vianco, Paul T.; Rejent, Jerome A.

1995-01-01

A lead-free solder alloy for electronic assemblies composed of a eutectic alloy of tin and silver with a bismuth addition, x, of 0

Tin-silver-bismuth solders for electronics assembly

DOEpatents

Vianco, P.T.; Rejent, J.A.

1995-08-08

A lead-free solder alloy is disclosed for electronic assemblies composed of a eutectic alloy of tin and silver with a bismuth addition, x, of 0

Two-stage epitaxial growth of vertically-aligned SnO 2 nano-rods on(001) ceria

DOE PAGES

Solovyov, Vyacheslav F.; Wu, Li-jun; Rupich, Martin W.; ...

2014-09-20

Growth of high-aspect ratio oriented tin oxide, SnO 2, nano-rods is complicated by a limited choice of matching substrates. We show that a (001) cerium oxide, CeO 2, surface uniquely enables epitaxial growth of tin-oxide nano-rods via a two-stage process. First, (100) oriented nano-wires coat the ceria surface by lateral growth, forming a uniaxially-textured SnO 2 deposit. Second, vertical SnO 2nano-rods nucleate on the deposit by homoepitaxy. We demonstrate growth of vertically oriented 1-2 μm long nano-rods with an average diameter of ≈20 nm.

Study of earth abundant tco and absorber materials for photovoltaic applications

NASA Astrophysics Data System (ADS)

Prabhakar, Tejas

In order to make photovoltaic power generation a sustainable venture, it is necessary to use cost-effective materials in the manufacture of solar cells. In this regard, AZO (Aluminum doped Zinc Oxide) and CZTS (Copper Zinc Tin Sulfide) have been studied for their application in thin film solar cells. While AZO is a transparent conducting oxide, CZTS is a photovoltaic absorber. Both AZO and CZTS consist of earth abundant elements and are non-toxic in nature. Highly transparent and conductive AZO thin films were grown using RF sputtering. The influence of deposition parameters such as working pressure, RF power, substrate temperature and flow rate on the film characteristics was investigated. The as-grown films had a high degree of preferred orientation along the (002) direction which enhanced at lower working pressures, higher RF powers and lower substrate temperatures. Williamson-Hall analysis on the films revealed that as the working pressure was increased, the nature of stress and strain gradually changed from being compressive to tensile. The fall in optical transmission of the films was a consequence of free carrier absorption resulting from enhanced carrier density due to incorporation of Al atoms or oxygen vacancies. The optical and electrical properties of the films were described well by the Burstein-Moss effect. CZTS absorber layers were grown using ultrasonic spray pyrolysis at a deposition temperature of 350 C and subsequently annealed in a sulfurization furnace. Measurements from XRD and Raman spectra confirmed the presence of pure single phase Cu2ZnSnS4. Texture analysis of as-deposited and annealed CZTS films indicated that the (112) plane which is characteristic of the kesterite phase was preferred. The grain size increased from 50 nm to 100 nm on conducting post-deposition annealing. CZTS films with stoichiometric composition yielded a band gap of 1.5 eV, which is optimal for solar energy conversion. The variation of tin in the film changed its resistivity by several orders of magnitude and subsequently the tin free ternary chalcogenide Cu2ZnS2 having very low resistivity was obtained. By carefully optimization of concentrations of tin, zinc and copper, a zinc-rich/tin-rich/copper-poor composition was found to be most suitable for solar cell applications. Etching of CZTS films using KCN solution reduced their resistivity, possibly due to the elimination of binary copper sulfide phases. CZTS solar cells were fabricated both in the substrate and superstrate configurations.

Fabrication of heterojunction solar cells by improved tin oxide deposition on insulating layer

DOEpatents

Feng, Tom; Ghosh, Amal K.

1980-01-01

Highly efficient tin oxide-silicon heterojunction solar cells are prepared by heating a silicon substrate, having an insulating layer thereon, to provide a substrate temperature in the range of about 300.degree. C. to about 400.degree. C. and thereafter spraying the so-heated substrate with a solution of tin tetrachloride in a organic ester boiling below about 250.degree. C. Preferably the insulating layer is naturally grown silicon oxide layer.

Epitaxial NbN/AlN/NbN tunnel junctions on Si substrates with TiN buffer layers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Rui; University of Chinese Academy of Sciences, Beijing 100049; Makise, Kazumasa

We have developed epitaxial NbN/AlN/NbN tunnel junctions on Si (100) substrates with a TiN buffer layer. A 50-nm-thick (200)-oriented TiN thin film was introduced as the buffer layer for epitaxial growth of NbN/AlN/NbN trilayers on Si substrates. The fabricated NbN/AlN/NbN junctions demonstrated excellent tunneling properties with a high gap voltage of 5.5 mV, a large I{sub c}R{sub N} product of 3.8 mV, a sharp quasiparticle current rise with a ΔV{sub g} of 0.4 mV, and a small subgap leakage current. The junction quality factor R{sub sg}/R{sub N} was about 23 for the junction with a J{sub c} of 47 A/cm{supmore » 2} and was about 6 for the junction with a J{sub c} of 3.0 kA/cm{sup 2}. X-ray diffraction and transmission electron microscopy observations showed that the NbN/AlN/NbN trilayers were grown epitaxially on the (200)-orientated TiN buffer layer and had a highly crystalline structure with the (200) orientation.« less

Two-stage epitaxial growth of vertically-aligned SnO2 nano-rods on (001) ceria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solovyov, VF; Wu, LJ; Rupich, MW

2014-12-15

Growth of high-aspect ratio oriented tin oxide, SnO2, nano-rods is complicated by a limited choice of matching substrates. We show that a (001) cerium oxide, CeO2, surface uniquely enables epitaxial growth of tin-oxide nano-rods via a two-stage process. First, (100) oriented nano-wires coat the ceria surface by lateral growth, forming a uniaxially-textured SnO2 deposit. Second, vertical SnO2 nano-rods nucleate on the deposit by homoepitaxy. We demonstrate growth of vertically oriented 1-2 mu m long nano-rods with an average diameter of approximate to 20 nm. 2014 Elsevier B.V. All rights reserved.

Room-temperature relaxor ferroelectricity and photovoltaic effects in tin titanate directly deposited on a silicon substrate

NASA Astrophysics Data System (ADS)

Agarwal, Radhe; Sharma, Yogesh; Chang, Siliang; Pitike, Krishna C.; Sohn, Changhee; Nakhmanson, Serge M.; Takoudis, Christos G.; Lee, Ho Nyung; Tonelli, Rachel; Gardner, Jonathan; Scott, James F.; Katiyar, Ram S.; Hong, Seungbum

2018-02-01

Tin titanate (SnTi O3 ) has been notoriously impossible to prepare as a thin-film ferroelectric, probably because high-temperature annealing converts much of the S n2 + to S n4 + . In the present paper, we show two things: first, perovskite phase SnTi O3 can be prepared by atomic-layer deposition directly onto p -type Si substrates; and second, these films exhibit ferroelectric switching at room temperature, with p -type Si acting as electrodes. X-ray diffraction measurements reveal that the film is single-phase, preferred-orientation ferroelectric perovskite SnTi O3 . Our films showed well-saturated, square, and repeatable hysteresis loops of around 3 μ C /c m2 remnant polarization at room temperature, as detected by out-of-plane polarization versus electric field and field cycling measurements. Furthermore, photovoltaic and photoferroelectricity were found in Pt /SnTi O3/Si /SnTi O3/Pt heterostructures, the properties of which can be tuned through band-gap engineering by strain according to first-principles calculations. This is a lead-free room-temperature ferroelectric oxide of potential device application.

Room-temperature relaxor ferroelectricity and photovoltaic effects in tin titanate directly deposited on a silicon substrate

DOE PAGES

Agarwal, Radhe; Sharma, Yogesh; Chang, Siliang; ...

2018-02-20

Tin titanate (SnTiO 3) has been notoriously impossible to prepare as a thin-film ferroelectric, probably because high-temperature annealing converts much of the Sn 2+ to Sn 4+. In the present paper, we show two things: first, perovskite phase SnTiO 3 can be prepared by atomic-layer deposition directly onto p-type Si substrates; and second, these films exhibit ferroelectric switching at room temperature, with p-type Si acting as electrodes. X-ray diffraction measurements reveal that the film is single-phase, preferred-orientation ferroelectric perovskite SnTiO 3. Our films showed well-saturated, square, and repeatable hysteresis loops of around 3μC/cm 2 remnant polarization at room temperature, asmore » detected by out-of-plane polarization versus electric field and field cycling measurements. Furthermore, photovoltaic and photoferroelectricity were found in Pt/SnTiO 3/Si/SnTiO 3/Pt heterostructures, the properties of which can be tuned through band-gap engineering by strain according to first-principles calculations. In conclusion, this is a lead-free room-temperature ferroelectric oxide of potential device application.« less

Room-temperature relaxor ferroelectricity and photovoltaic effects in tin titanate directly deposited on a silicon substrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agarwal, Radhe; Sharma, Yogesh; Chang, Siliang

Tin titanate (SnTiO 3) has been notoriously impossible to prepare as a thin-film ferroelectric, probably because high-temperature annealing converts much of the Sn 2+ to Sn 4+. In the present paper, we show two things: first, perovskite phase SnTiO 3 can be prepared by atomic-layer deposition directly onto p-type Si substrates; and second, these films exhibit ferroelectric switching at room temperature, with p-type Si acting as electrodes. X-ray diffraction measurements reveal that the film is single-phase, preferred-orientation ferroelectric perovskite SnTiO 3. Our films showed well-saturated, square, and repeatable hysteresis loops of around 3μC/cm 2 remnant polarization at room temperature, asmore » detected by out-of-plane polarization versus electric field and field cycling measurements. Furthermore, photovoltaic and photoferroelectricity were found in Pt/SnTiO 3/Si/SnTiO 3/Pt heterostructures, the properties of which can be tuned through band-gap engineering by strain according to first-principles calculations. In conclusion, this is a lead-free room-temperature ferroelectric oxide of potential device application.« less

Effect of the Tin- versus Air-side Plate-glass Orientation on the Impact Response and Penetration Resistance of a Laminated Transparent Armour Structure

DTIC Science & Technology

2012-01-16

January 2012 2012 226:Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials Design and Applications M Grujicic, W C Bell...unclassified c . THIS PAGE unclassified Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std Z39-18 Effect of the tin- versus air-side plate-glass...orientation on the impact response and penetration resistance of a laminated transparent armour structure M Grujicic1*, W C Bell1, B Pandurangan1, B

Heteroepitaxial growth of tin-doped indium oxide films on single crystalline yttria stabilized zirconia substrates

NASA Astrophysics Data System (ADS)

Kamei, Masayuki; Yagami, Teruyuki; Takaki, Satoru; Shigesato, Yuzo

1994-05-01

Heteroepitaxial growth of tin-doped indium oxide (ITO) film was achieved for the first time by using single crystalline yttria stabilized zirconia (YSZ) as substrates. The epitaxial relationship between ITO film and YSZ substrate was ITO[100]∥YSZ[100]. By comparing the electrical properties of this epitaxial ITO film with that of a randomly oriented polycrystalline ITO film grown on a glass substrate, neither the large angle grain boundaries nor the crystalline orientation were revealed to be dominant in determining the carrier mobility in ITO films.

Auger electron spectroscopy study of surface segregation in the binary alloys copper-1 atomic percent indium, copper-2 atomic percent tin, and iron-6.55 atomic percent silicon

NASA Technical Reports Server (NTRS)

Ferrante, J.

1973-01-01

Auger electron spectroscopy was used to examine surface segregation in the binary alloys copper-1 at. % indium, copper-2 at. % tin and iron-6.55 at. % silicon. The copper-tin and copper-indium alloys were single crystals oriented with the /111/ direction normal to the surface. An iron-6.5 at. % silicon alloy was studied (a single crystal oriented in the /100/ direction for study of a (100) surface). It was found that surface segregation occurred following sputtering in all cases. Only the iron-silicon single crystal alloy exhibited equilibrium segregation (i.e., reversibility of surface concentration with temperature) for which at present we have no explanation. McLean's analysis for equilibrium segregation at grain boundaries did not apply to the present results, despite the successful application to dilute copper-aluminum alloys. The relation of solute atomic size and solubility to surface segregation is discussed. Estimates of the depth of segregation in the copper-tin alloy indicate that it is of the order of a monolayer surface film.

The structure and properties of pulsed dc magnetron sputtered nanocrystalline TiN films for electrodes of alkali metal thermal-to-electric conversion systems.

PubMed

Chun, Sung-Yong

2013-03-01

Titanium nitride films used as an important electrode material for the design of alkali metal thermal-to-electric conversion (AMTEC) system have been prepared using dc (direct current) and asymmetric-bipolar pulsed dc magnetron sputtering. The pulse frequency and the duty cycle were varied from 5 to 50 kHz and 50 to 95%, respectively. The deposition rate, grain size and resistivity of pulsed dc sputtered films were decreased when the pulse frequency increased, while the nano hardness of titanium nitride films increased. We present in detail coatings (e.g., deposition rate, grain size, prefer-orientation, resistivity and hardness). Our studies show that titanium nitride coatings with superior properties can be prepared using asymmetric-bipolar pulsed dc sputtering.

Method of fabricating conducting oxide-silicon solar cells utilizing electron beam sublimation and deposition of the oxide

DOEpatents

Feng, Tom; Ghosh, Amal K.

1979-01-01

In preparing tin oxide and indium tin oxide-silicon heterojunction solar cells by electron beam sublimation of the oxide and subsequent deposition thereof on the silicon, the engineering efficiency of the resultant cell is enhanced by depositing the oxide at a predetermined favorable angle of incidence. Typically the angle of incidence is between 40.degree. and 70.degree. and preferably between 55.degree. and 65.degree. when the oxide is tin oxide and between 40.degree. and 70.degree. when the oxide deposited is indium tin oxide. gi The Government of the United States of America has rights in this invention pursuant to Department of Energy Contract No. EY-76-C-03-1283.

Gibbs–Thomson Effect in Planar Nanowires: Orientation and Doping Modulated Growth

DOE PAGES

Shen, Youde; Chen, Renjie; Yu, Xuechao; ...

2016-06-02

Epitaxy-enabled bottom-up synthesis of self-assembled planar nanowires via the vapor–liquid–solid mechanism is an emerging and promising approach toward large-scale direct integration of nanowire-based devices without postgrowth alignment. In this paper, by examining large assemblies of indium tin oxide nanowires on yttria-stabilized zirconia substrate, we demonstrate for the first time that the growth dynamics of planar nanowires follows a modified version of the Gibbs–Thomson mechanism, which has been known for the past decades to govern the correlations between thermodynamic supersaturation, growth speed, and nanowire morphology. Furthermore, the substrate orientation strongly influences the growth characteristics of epitaxial planar nanowires as opposed tomore » impact at only the initial nucleation stage in the growth of vertical nanowires. The rich nanowire morphology can be described by a surface-energy-dependent growth model within the Gibbs–Thomson framework, which is further modulated by the tin doping concentration. Our experiments also reveal that the cutoff nanowire diameter depends on the substrate orientation and decreases with increasing tin doping concentration. Finally, these results enable a deeper understanding and control over the growth of planar nanowires, and the insights will help advance the fabrication of self-assembled nanowire devices.« less

Gibbs-Thomson Effect in Planar Nanowires: Orientation and Doping Modulated Growth.

PubMed

Shen, Youde; Chen, Renjie; Yu, Xuechao; Wang, Qijie; Jungjohann, Katherine L; Dayeh, Shadi A; Wu, Tom

2016-07-13

Epitaxy-enabled bottom-up synthesis of self-assembled planar nanowires via the vapor-liquid-solid mechanism is an emerging and promising approach toward large-scale direct integration of nanowire-based devices without postgrowth alignment. Here, by examining large assemblies of indium tin oxide nanowires on yttria-stabilized zirconia substrate, we demonstrate for the first time that the growth dynamics of planar nanowires follows a modified version of the Gibbs-Thomson mechanism, which has been known for the past decades to govern the correlations between thermodynamic supersaturation, growth speed, and nanowire morphology. Furthermore, the substrate orientation strongly influences the growth characteristics of epitaxial planar nanowires as opposed to impact at only the initial nucleation stage in the growth of vertical nanowires. The rich nanowire morphology can be described by a surface-energy-dependent growth model within the Gibbs-Thomson framework, which is further modulated by the tin doping concentration. Our experiments also reveal that the cutoff nanowire diameter depends on the substrate orientation and decreases with increasing tin doping concentration. These results enable a deeper understanding and control over the growth of planar nanowires, and the insights will help advance the fabrication of self-assembled nanowire devices.

Influence of silicon oxide on the performance of TiN bottom electrode in phase change memory

NASA Astrophysics Data System (ADS)

Gao, Dan; Liu, Bo; Xu, Zhen; Wang, Heng; Xia, Yangyang; Wang, Lei; Zhu, Nanfei; Li, Ying; Zhan, Yipeng; Song, Zhitang; Feng, Songlin

2016-10-01

The stability of TiN which is the preferred bottom electrode contact (BEC) of phase change memory (PCM) due to its low thermal conductivity and suitable electrical conductivity, is very essential to the reliability of PCM devices. In this work, in order to investigate the effect of high aspect ratio process (HARP) SiO2 on the performance of TiN, both TiN/SiO2, TiN/SiN thin films and TiN BEC device structures are analyzed. By combining transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS), we found that the TiN would be oxidized after the deposition of HARP SiO2 and there exist a thin ( 4 nm) oxidation interfacial layer between TiN and SiO2. Electrical measurements were performed on the 1R PCM test-key die with 7 nm and 10 nm BEC-only cells. The statistical initial resistances of BEC have wide distribution and it is confirmed that the non-uniform oxidation of TiN BEC affects the astringency of the resistance of TiN BEC. The experimental results help to optimize the process of TiN BEC, and SiN is recommended as a better choice as the linear layer.

Process for preparing titanium nitride powder

DOEpatents

Bamberger, C.E.

1988-06-17

A process for making titanium nitride powder by reaction of titanium phosphates with sodium cyanide. The process of this invention may comprise mixing one or more phosphates of Ti with a cyanide salt in the absence of oxygen and heating to a temperature sufficient to cause reaction to occur. In the preferred embodiment the ratio of cyanide salt to Ti should be at least 2 which results in the major Ti-containing product being TiN rather than sodium titanium phosphate byproducts. The process is an improvement over prior processes since the byproducts are water soluble salts of sodium which can easily be removed from the preferred TiN product by washing. 2 tabs.

Method of preparing composite superconducting wire

DOEpatents

Verhoeven, John D.; Gibson, Edwin D.; Finnemore, Douglas K.; Ostenson, Jerome E.; Schmidt, Frederick A.; Owen, Charles V.

1985-08-06

An improved method of preparing composite multifilament superconducting wire of Nb.sub.3 Sn in a copper matrix which eliminates the necessity of coating the drawn wire with tin. A generalized cylindrical billet of an alloy of copper containing at least 15 weight percent niobium, present in the copper as discrete, randomly distributed and oriented dendritic-shaped particles, is provided with at least one longitudinal opening which is filled with tin to form a composite drawing rod. The drawing rod is then drawn to form a ductile composite multifilament wire containing a filament of tin. The ductile wire containing the tin can then be wound into magnet coils or other devices before heating to diffuse the tin through the wire to react with the niobium forming Nb.sub.3 Sn. Also described is an improved method for making large billets of the copper-niobium alloy by consumable-arc casting.

Improved method of preparing composite superconducting wire

DOEpatents

Verhoeven, J.D.; Gibson, E.D.; Finnemore, D.K.; Ostenson, J.E.; Schmidt, F.A.; Owen, C.V.

1979-10-17

An improved method of preparing composite multifilament superconducting wire of Nb/sub 3/Sn in a copper matrix eliminates the necessity of coating the drawn wire with tin. A generalized cylindrical billet of an alloy of copper containing at least 15 weight percent niobium, present in the copper as discrete, randomly distributed and oriented dendritic-shaped particles, is provided with at least one longitudinal opening which is filled with tin to form a composite drawing rod. The drawing rod is then drawn to form a ductile composite multifilament wire containing a filament of tin. The ductile wire containing the tin can then be wound into magnet coils or other devices before heating to diffuse the tin through the wire to react with the niobium forming Nb/sub 3/Sn. Also described is an improved method for making large billets of the copper-niobium alloy by consumable-arc casting.

Structure of assemblies of metal nanowires in mesoporous alumina membranes studied by EXAFS, XANES, X-ray diffraction and SAXS.

PubMed

Benfield, Robert E; Grandjean, Didier; Dore, John C; Esfahanian, Hamid; Wu, Zhonghua; Kröll, Michael; Geerkens, Marcus; Schmid, Günter

2004-01-01

Mesoporous alumina membranes ("anodic aluminium oxide", or "AAO") are made by anodic oxidation of aluminium metal. These membranes contain hexagonal arrays of parallel non-intersecting cylindrical pores perpendicular to the membrane surface. By varying the anodisation voltage, the pore diameters are controllable within the range 5-250 nm. We have used AAO membranes as templates for the electrochemical deposition of metals within the pores to produce nanowires. These represent assemblies of one-dimensional quantum wires with prospective applications in electronic, optoelectronic and magnetic devices. Detailed characterisation of the structures of these nanowire assemblies on a variety of length scales is essential to understand their physical properties and evaluate their possible applications. We have used EXAFS, XANES, WAXS, high energy X-ray diffraction and SAXS to study their structure and bonding. In this paper we report the results of our studies of four different nanowire systems supported in AAO membranes. These are the ferromagnetic metals iron and cobalt, the superconducting metal tin, and the semiconductor gallium nitride. Iron nanowires in pores of diameter over the range 12 nm-72 nm are structurally very similar to bcc bulk iron. They have a strong preferred orientation within the alumina pores. Their XANES shows significant differences from that of bulk iron, showing that the electronic structure of the iron nanowires depends systematically on their diameter. Cobalt nanowires are composed of a mixture of hcp and fcc phases, but the ratio of the two phases does not depend in a simple way on the pore diameter or preparation conditions. In bulk cobalt, the fcc beta-phase is normally stable only at high temperatures. Strong preferred orientation of the c-axis in the pores was found. Tin nanowires in alumina membranes with pores diameters between 12 nm and 72 nm have a tetragonal beta-structure at ambient temperature and also at 80 K. Magnetic susceptibility measurements show that they are diamagnetic, and become superconducting at the same temperature as bulk tin (3.7 K). Gallium nitride nanowires have been prepared in alumina membranes with pore diameter 24 nm by a novel method. Gallium nitrate was deposited in the pores from aqueous solution and thermolysed at 1000 degrees C to form Ga2O3, which was reacted with ammonia at 1000 degrees C. The GaN nanowires have the wurtzite structure. Preparation at 1150 degrees C led to the incorporation of aluminium in the GaN. The mesoscopic ordering of the pores in the AAO membranes and their filling by metal nanowires has been studied by SAXS, which shows patterns of Bragg peaks arising from the pore arrays. Additionally, the cobalt nanowires have been the subject of an initial ASAXS study.

Is there a common orientational order for the liquid phase of tetrahedral molecules?

PubMed

Rey, Rossend

2009-08-14

The title question is addressed with molecular dynamics simulations for a broad set of molecules: methane (CH4), neopentane (C(CH3)4), carbon tetrafluoride (CF4), carbon tetrachloride (CCl4), silicon tetrachloride (SiCl4), vanadium tetrachloride (VCl4), tin tetrachloride (SnCl4), carbon tetrabromide (CBr4), and tin tetraiodide (SnI4). In all cases the sequence of most populated relative orientations, for increasing distances, is found to be identical: The closest distances correspond to face-to-face followed by a dominant role of edge-to-face, while for larger distances the main configuration is edge-to-edge. The corner-to-face configuration plays an almost negligible role. The range of orientational order is also similar, with remnants of orientational correlation discernible up to the fourth solvation shell. The equivalence does not only hold in the qualitative terms just stated but is also quantitative to a large extent once the center-center distance is properly scaled.

Is there a common orientational order for the liquid phase of tetrahedral molecules?

NASA Astrophysics Data System (ADS)

Rey, Rossend

2009-08-01

The title question is addressed with molecular dynamics simulations for a broad set of molecules: methane (CH4), neopentane (C(CH3)4), carbon tetrafluoride (CF4), carbon tetrachloride (CCl4), silicon tetrachloride (SiCl4), vanadium tetrachloride (VCl4), tin tetrachloride (SnCl4), carbon tetrabromide (CBr4), and tin tetraiodide (SnI4). In all cases the sequence of most populated relative orientations, for increasing distances, is found to be identical: The closest distances correspond to face-to-face followed by a dominant role of edge-to-face, while for larger distances the main configuration is edge-to-edge. The corner-to-face configuration plays an almost negligible role. The range of orientational order is also similar, with remnants of orientational correlation discernible up to the fourth solvation shell. The equivalence does not only hold in the qualitative terms just stated but is also quantitative to a large extent once the center-center distance is properly scaled.

The Effect of Microgravity on the Growth of Lead Tin Telluride

NASA Technical Reports Server (NTRS)

Narayanan, R.

2000-01-01

The main objective of this research was to present a model for the prediction of the effect of the microgravity environment on the growth of Lead Tin Telluride. The attitude change and its relation to the experimental objectives: The main objective for the AADSF experiment on USMP 3 involving LTT growth was to estimate the effect of ampoule orientation on the axial and radial segregation of tin telluride. As the furnace was not situated on a gimbal there was no possibility to reorient the ampoule during the flight. Instead the only way to change the growth orientation was to change the attitude of the orbiter. This was accomplished by vernier rocket firings. In what follows it must be noted that the orbiter body coordinates are such that the positive z axis points outward from the 'belly', the positive 'x' axis points outwards from the nose and the positive 'y' axis points outwards from the starboard side. The furnace which was in the pay load had its axis aligned with the orbiter's 'z' axis with the hot end closest to the shuttle body. There were basically three orientations that were desired. These corresponded to the ampoule being seen as a heated from above (thermally stable-solutally unstable) configuration, the heated from below (where the instabilities were reversed from the first orientation) configuration and an 'in between' case where the ampoule axis was misaligned with respect to the orbiters 'g(sub z)' axis.

Pulse electrodeposited nickel-indium tin oxide nanocomposite as an electrocatalyst for non-enzymatic glucose sensing.

PubMed

Sivasakthi, P; Ramesh Bapu, G N K; Chandrasekaran, Maruthai

2016-01-01

Nickel and nickel-ITO nanocomposite on mild steel substrate were prepared by pulse electrodeposition method from nickel sulphamate electrolyte and were examined as electrocatalysts for non-enzymatic glucose sensing. The surface morphology, chemical composition, preferred orientation and oxidation states of the nickel metal ion in the deposits were characterized by SEM, EDAX, XRD and XPS. Electrochemical sensing of glucose was studied by cyclic voltammetry and amperometry. The modified Ni-ITO nanocomposite electrode showed higher electrocatalytic activity for the oxidation of glucose in alkaline medium and exhibited a linear range from 0.02 to 3.00 mM with a limit of detection 3.74 μM at a signal-to-noise ratio of 3. The higher selectivity, longer stability and better reproducibility of this electrode compared to nickel in the sensing of glucose are pointers for exploitation in practical clinical applications. Copyright © 2015 Elsevier B.V. All rights reserved.

Effect of prior deformation on microstructural development and Laves phase precipitation in high-chromium stainless steel.

PubMed

Hsiao, Z-W; Chen, D; Kuo, J-C; Lin, D-Y

2017-04-01

This study investigated the influence of deformation on precipitation behaviour and microstructure change during annealing. Here, the prior deformation of high-chromium stainless steel was tensile deformation of 3%, 6% and 10%, and the specimens were then annealed at 700˚C for 10 h. The specimens were subsequently analyzed using backscattered electron image and electron backscattering diffraction measurements with SEM. Compared with the deformation microstructure, the grains revealed no preferred orientation. The precipitates of TiN and NbC were formed homogenously in the grain interior and at grain boundaries after annealing. Fine Laves phase precipitates were observed in grains and along subgrain boundaries as the deformation increased. Furthermore, the volume fraction of Laves phase increased, but the average particle diameter of precipitate was reduced as the deformation increased. © 2017 The Authors Journal of Microscopy © 2017 Royal Microscopical Society.

Structural, electrical, and optical properties of antimony-doped tin oxide films prepared at room temperature by radio frequency magnetron sputtering for transparent electrodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Sung Uk; Hong, Byungyou; Choi, Won Seok

2009-07-15

Antimony-doped tin oxide (ATO) films were prepared on 7059 Corning glass substrate by the radio frequency (rf) magnetron sputtering method using SnO{sub 2} target mixed with Sb of 6 wt % at room temperature. The working pressure was varied from 0.67 to 2 Pa in steps of 0.67 Pa, and the rf power was varied from 100 to 175 W in steps of 25 W at room temperature. The thickness of the deposited ATO films was about 150 nm. X-ray diffraction (XRD) measurements showed the ATO films to be crystallized with a strong (101) preferred orientation as the rf powermore » is increased. The spectra revealed that the deposited films were polycrystalline, retaining the tetragonal structure. The grain size was estimated from the XRD spectra using the Scherrer equation and found to decrease with a decrease in the working pressure and an increase in the rf power, while the surface roughness was observed to be smoothened. The ATO film that was deposited at a working pressure of 0.67 Pa with rf power of 175 W showed the lowest resistivity of 8.6x10{sup -3} {Omega} cm, and the optical transmittance was 86.5% in the visible wavelength range from 400 to 800 nm.« less

Multi-phase structures of boron-doped copper tin sulfide nanoparticles synthesized by chemical bath deposition for optoelectronic devices

NASA Astrophysics Data System (ADS)

Rakspun, Jariya; Kantip, Nathakan; Vailikhit, Veeramol; Choopun, Supab; Tubtimtae, Auttasit

2018-04-01

We investigated the influence of boron doping on the structural, optical, and electrical properties of copper tin sulfide (CTS) nanoparticles coated on a WO3 surface and synthesized using chemical bath deposition. Boron doping at concentrations of 0.5, 1.0, 1.5, and 2.0 wt% was investigated. The X-ray diffraction pattern of CTS showed the presence of monoclinic Cu2Sn3S7, cubic Cu2SnS3, and orthorhombic Cu4SnS4. Boron doping influenced the preferred orientation of the nanoparticles for all phase structures and produced a lattice strain effect and changes in the dislocation density. Increasing the concentration of boron in CTS from 0.5 wt% to 2.0 wt% reduced the band gap for all phases of CTS from 1.46 to 1.29 eV and reduced the optical transmittance. Optical constants, such as the refractive index, extinction coefficient, and dissipation factor, were also obtained for B-doped CTS. The dispersion behavior of the refractive index was investigated in terms of a single oscillator model and the physical parameters were determined. Fourier transform infrared spectroscopy confirmed the successful synthesis of CTS nanoparticles. Cyclic voltammetry indicated that optimum boron doping (<1.5 wt% for all phases) resulted in desirable p-n junction behavior for optoelectronic applications.

The role of titanium nitride supports for single-atom platinum-based catalysts in fuel cell technology.

PubMed

Zhang, Ren-Qin; Lee, Tae-Hun; Yu, Byung-Deok; Stampfl, Catherine; Soon, Aloysius

2012-12-28

As a first step towards a microscopic understanding of single-Pt atom-dispersed catalysts on non-conventional TiN supports, we present density-functional theory (DFT) calculations to investigate the adsorption properties of Pt atoms on the pristine TiN(100) surface, as well as the dominant influence of surface defects on the thermodynamic stability of platinized TiN. Optimized atomic geometries, energetics, and analysis of the electronic structure of the Pt/TiN system are reported for various surface coverages of Pt. We find that atomic Pt does not bind preferably to the clean TiN surface, but under typical PEM fuel cell operating conditions, i.e. strongly oxidizing conditions, TiN surface vacancies play a crucial role in anchoring the Pt atom for its catalytic function. Whilst considering the energetic stability of the Pt/TiN structures under varying N conditions, embedding Pt at the surface N-vacancy site is found to be the most favorable under N-lean conditions. Thus, the system of embedding Pt at the surface N-vacancy sites on TiN(100) surfaces could be promising catalysts for PEM fuel cells.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meng, Yifei; Zuo, Jian -Min

A diffraction-based technique is developed for the determination of three-dimensional nanostructures. The technique employs high-resolution and low-dose scanning electron nanodiffraction (SEND) to acquire three-dimensional diffraction patterns, with the help of a special sample holder for large-angle rotation. Grains are identified in three-dimensional space based on crystal orientation and on reconstructed dark-field images from the recorded diffraction patterns. Application to a nanocrystalline TiN thin film shows that the three-dimensional morphology of columnar TiN grains of tens of nanometres in diameter can be reconstructed using an algebraic iterative algorithm under specified prior conditions, together with their crystallographic orientations. The principles can bemore » extended to multiphase nanocrystalline materials as well. Furthermore, the tomographic SEND technique provides an effective and adaptive way of determining three-dimensional nanostructures.« less

Development and matching of binocular orientation preference in mouse V1.

PubMed

Bhaumik, Basabi; Shah, Nishal P

2014-01-01

Eye-specific thalamic inputs converge in the primary visual cortex (V1) and form the basis of binocular vision. For normal binocular perceptions, such as depth and stereopsis, binocularly matched orientation preference between the two eyes is required. A critical period of binocular matching of orientation preference in mice during normal development is reported in literature. Using a reaction diffusion model we present the development of RF and orientation selectivity in mouse V1 and investigate the binocular orientation preference matching during the critical period. At the onset of the critical period the preferred orientations of the modeled cells are mostly mismatched in the two eyes and the mismatch decreases and reaches levels reported in juvenile mouse by the end of the critical period. At the end of critical period 39% of cells in binocular zone in our model cortex is orientation selective. In literature around 40% cortical cells are reported as orientation selective in mouse V1. The starting and the closing time for critical period determine the orientation preference alignment between the two eyes and orientation tuning in cortical cells. The absence of near neighbor interaction among cortical cells during the development of thalamo-cortical wiring causes a salt and pepper organization in the orientation preference map in mice. It also results in much lower % of orientation selective cells in mice as compared to ferrets and cats having organized orientation maps with pinwheels.

Comparative study of ITO and TiN fabricated by low-temperature RF biased sputtering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simon, Daniel K., E-mail: daniel.simon@namlab.com; Schenk, Tony; Dirnstorfer, Ingo

2016-03-15

Radio frequency (RF) biasing induced by a second plasma source at the substrate is applied to low-temperature sputtering processes for indium tin oxide (ITO) and titanium nitride (TiN) thin films. Investigations on crystal structure and surface morphology show that RF-biased substrate plasma processes result in a changed growth regime with different grain sizes and orientations than those produced by processes without a substrate bias. The influence of the RF bias is shown comparatively for reactive RF-sputtered ITO and reactive direct-current-sputtered TiN. The ITO layers exhibit an improved electrical resistivity of 0.5 mΩ cm and an optical absorption coefficient of 0.5 × 10{sup 4 }cm{supmore » −1} without substrate heating. Room-temperature sputtered TiN layers are deposited that possess a resistivity (0.1 mΩ cm) of 3 orders of magnitude lower than, and a density (5.4 g/cm{sup 3}) up to 45% greater than, those obtained from layers grown using the standard process without a substrate plasma.« less

Development and matching of binocular orientation preference in mouse V1

PubMed Central

Bhaumik, Basabi; Shah, Nishal P.

2014-01-01

Eye-specific thalamic inputs converge in the primary visual cortex (V1) and form the basis of binocular vision. For normal binocular perceptions, such as depth and stereopsis, binocularly matched orientation preference between the two eyes is required. A critical period of binocular matching of orientation preference in mice during normal development is reported in literature. Using a reaction diffusion model we present the development of RF and orientation selectivity in mouse V1 and investigate the binocular orientation preference matching during the critical period. At the onset of the critical period the preferred orientations of the modeled cells are mostly mismatched in the two eyes and the mismatch decreases and reaches levels reported in juvenile mouse by the end of the critical period. At the end of critical period 39% of cells in binocular zone in our model cortex is orientation selective. In literature around 40% cortical cells are reported as orientation selective in mouse V1. The starting and the closing time for critical period determine the orientation preference alignment between the two eyes and orientation tuning in cortical cells. The absence of near neighbor interaction among cortical cells during the development of thalamo-cortical wiring causes a salt and pepper organization in the orientation preference map in mice. It also results in much lower % of orientation selective cells in mice as compared to ferrets and cats having organized orientation maps with pinwheels. PMID:25104927

Sex-role orientation associations with college students' body-image preferences.

PubMed

Johnson, H Durell; Lamont, Janine; Monacelli, Jennifer; Vojick, Alex

2004-12-01

Sex roles dictate acceptable attitudes and preferences for men and women. Further, perception of ideal body type is one attitude and preference that may be associated with sex-role orientation. Therefore, the current study examined the association between sex-role orientation and men's and women's reports of their preferred body type and their views of others' preferred body type for men and women. Responses from 172 university students indicated sex-role associations with participants' personal body-type preferences and participants' perceptions of the body types others prefer. Analysis indicates that a more masculine sex-role orientation was associated with men's and women's perceptions of larger ideal body images. Results are discussed in terms of the association between sex-role orientation and possible susceptibility to societal standards of ideal body images.

Three-dimensional nanostructure determination from a large diffraction data set recorded using scanning electron nanodiffraction.

PubMed

Meng, Yifei; Zuo, Jian-Min

2016-09-01

A diffraction-based technique is developed for the determination of three-dimensional nanostructures. The technique employs high-resolution and low-dose scanning electron nanodiffraction (SEND) to acquire three-dimensional diffraction patterns, with the help of a special sample holder for large-angle rotation. Grains are identified in three-dimensional space based on crystal orientation and on reconstructed dark-field images from the recorded diffraction patterns. Application to a nanocrystalline TiN thin film shows that the three-dimensional morphology of columnar TiN grains of tens of nanometres in diameter can be reconstructed using an algebraic iterative algorithm under specified prior conditions, together with their crystallographic orientations. The principles can be extended to multiphase nanocrystalline materials as well. Thus, the tomographic SEND technique provides an effective and adaptive way of determining three-dimensional nanostructures.

On the influence of DC electric fields on the aerosol assisted chemical vapor deposition growth of photoactive titanium dioxide thin films.

PubMed

Romero, Luz; Binions, Russell

2013-11-05

Titanium dioxide thin films were deposited on fluorine doped tin oxide glass substrate from the electric field assisted aerosol chemical vapor deposition (EACVD) reaction of titanium isopropoxide (TTIP, Ti(OC3H7)4) in toluene on glass substrates at a temperature of 450 °C. DC electric fields were generated by applying a potential difference between the electrodes of the transparent coated oxide coated glass substrates during the deposition. The deposited films were characterized using scanning electron microscopy, X-ray diffraction, atomic force microscopy, Raman spectroscopy, and UV-vis spectroscopy. The photoactivity and hydrophilicity of the deposited films were also analyzed using a dye-ink test and water-contact angle measurements. The characterization work revealed that the incorporation of DC electric fields produced significant reproducible changes in the film microstructure, preferred crystallographic orientation, roughness, and film thickness. Photocatalytic activity was calculated from the half-time (t1/2) or time taken to degrade 50% of the initial resazurin dye concentration. A large improvement in photocatalytic activity was observed for films deposited using an electric field with a strong orientation in the (004) direction (t1/2 17 min) as compared to a film deposited with no electric field (t1/2 40 min).

Refining As-cast β-Ti Grains Through ZrN Inoculation

NASA Astrophysics Data System (ADS)

Qiu, Dong; Zhang, Duyao; Easton, Mark A.; St John, David H.; Gibson, Mark A.

2018-03-01

The columnar-to-equiaxed transition and remarkable refinement of β-Ti grains occur in an as-cast Ti-13Mo alloy when a new grain refiner, ZrN, was inoculated at a nitrogen level as low as 0.4 wt pct. The grain refining effect is attributed to in situ-formed TiN particles that provide active nucleation sites and solute Zr that promotes constitutional supercooling. Reproducible orientation relationships were identified between TiN nucleants and β-Ti matrix, and well explained by the edge-to-edge matching model.

Orientation Preferences and Motion Sickness Induced in a Virtual Reality Environment.

PubMed

Chen, Wei; Chao, Jian-Gang; Zhang, Yan; Wang, Jin-Kun; Chen, Xue-Wen; Tan, Cheng

2017-10-01

Astronauts' orientation preferences tend to correlate with their susceptibility to space motion sickness (SMS). Orientation preferences appear universally, since variable sensory cue priorities are used between individuals. However, SMS susceptibility changes after proper training, while orientation preferences seem to be intrinsic proclivities. The present study was conducted to investigate whether orientation preferences change if susceptibility is reduced after repeated exposure to a virtual reality (VR) stimulus environment that induces SMS. A horizontal supine posture was chosen to create a sensory context similar to weightlessness, and two VR devices were used to produce a highly immersive virtual scene. Subjects were randomly allocated to an experimental group (trained through exposure to a provocative rotating virtual scene) and a control group (untrained). All subjects' orientation preferences were measured twice with the same interval, but the experimental group was trained three times during the interval, while the control group was not. Trained subjects were less susceptible to SMS, with symptom scores reduced by 40%. Compared with untrained subjects, trained subjects' orientation preferences were significantly different between pre- and posttraining assessments. Trained subjects depended less on visual cues, whereas few subjects demonstrated the opposite tendency. Results suggest that visual information may be inefficient and unreliable for body orientation and stabilization in a rotating visual scene, while reprioritizing preferences for different sensory cues was dynamic and asymmetric between individuals. The present findings should facilitate customization of efficient and proper training for astronauts with different sensory prioritization preferences and dynamic characteristics.Chen W, Chao J-G, Zhang Y, Wang J-K, Chen X-W, Tan C. Orientation preferences and motion sickness induced in a virtual reality environment. Aerosp Med Hum Perform. 2017; 88(10):903-910.

Effect of Sn doping on the structural, optical and electrical properties of TiO2 films prepared by spray pyrolysis

NASA Astrophysics Data System (ADS)

Arunachalam, A.; Dhanapandian, S.; Manoharan, C.

2016-02-01

In this work, highly oriented pure and Tin-doped Titanium dioxide (Sn-doped TiO2) with porous nature photoelectrodes were deposited on ITO glass plates using spray pyrolysis technique. The XRD pattern revealed the formation of anatase TiO2 with the maximum intensity of (101) plane while doping 6 at% of Sn. The morphological studies depicted the porous nature with the uniform arrangement of small-sized grains. The presence of tin confirmed with the EDX spectra. The size of particles of 13 nm was observed from High Resolution Transmission Electron Microscopy (HR-TEM) analysis. The average transmittance was about 85% for the doped photoelectrode and was observed for the photoelectrode deposited with 6 at% of tin, with decreased energy band gap. The PL study showed the emission peak at 391 nm. The maximum carrier concentration and Hall mobility was observed for the photoelectrode deposited with 6 at% of tin. With these studies, the DSSCs were prepared separately with the dye extracted from Hibiscus Rosasinesis and Hibiscus Surttasinesis and their efficiency was maximum for the DSSC prepared with 6 at% of tin.

First-principles analysis of structural and opto-electronic properties of indium tin oxide

NASA Astrophysics Data System (ADS)

Tripathi, Madhvendra Nath; Shida, Kazuhito; Sahara, Ryoji; Mizuseki, Hiroshi; Kawazoe, Yoshiyuki

2012-05-01

Density functional theory (DFT) and DFT + U (DFT with on-site Coulomb repulsion corrections) calculations have been carried out to study the structural and opto-electronic properties of indium tin oxide (ITO) for both the oxidized and reduced environment conditions. Some of the results obtained by DFT calculations differ from the experimental observations, such as uncertain indication for the site preference of tin atom to replace indium atom at b-site or d-site, underestimation of local inward relaxation in the first oxygen polyhedra around tin atom, and also the improper estimation of electronic density of states and hence resulting in an inappropriate optical spectra of ITO. These discrepancies of theoretical outcomes with experimental observations in ITO arise mainly due to the underestimation of the cationic 4d levels within standard DFT calculations. Henceforth, the inclusion of on-site corrections within DFT + U framework significantly modifies the theoretical results in better agreement to the experimental observations. Within this framework, our calculations show that the indium b-site is preferential site over d-site for tin atom substitution in indium oxide under both the oxidized and reduced conditions. Moreover, the calculated average inward relaxation value of 0.16 Å around tin atom is in good agreement with the experimental value of 0.18 Å. Furthermore, DFT + U significantly modify the electronic structure and consequently induce modifications in the calculated optical spectra of ITO.

Three-dimensional nanostructure determination from a large diffraction data set recorded using scanning electron nanodiffraction

DOE PAGES

Meng, Yifei; Zuo, Jian -Min

2016-07-04

A diffraction-based technique is developed for the determination of three-dimensional nanostructures. The technique employs high-resolution and low-dose scanning electron nanodiffraction (SEND) to acquire three-dimensional diffraction patterns, with the help of a special sample holder for large-angle rotation. Grains are identified in three-dimensional space based on crystal orientation and on reconstructed dark-field images from the recorded diffraction patterns. Application to a nanocrystalline TiN thin film shows that the three-dimensional morphology of columnar TiN grains of tens of nanometres in diameter can be reconstructed using an algebraic iterative algorithm under specified prior conditions, together with their crystallographic orientations. The principles can bemore » extended to multiphase nanocrystalline materials as well. Furthermore, the tomographic SEND technique provides an effective and adaptive way of determining three-dimensional nanostructures.« less

Study on preferred crystal orientations of Mg-Zr-O composite protective layer in AC-PDP

NASA Astrophysics Data System (ADS)

Bingang, G.; Chunliang, L.; Zhongxiao, S.; Liu, L.; Yufeng, F.; Xing, X.; Duowang, F.

2006-11-01

In order to study the preferred crystal orientations of Mg-Zr-O composite protective layers in PDP, Mg-Zr-O composite protective layers were deposited by Electron-beam Evaporator using (MgO+ZrO{2}) powder mixture as evaporation source material. X-ray diffractometer (XRD) was used to determine preferred crystal orientations of Mg-Zr-O composite protective layers, surface morphologies of films were analyzed by FESEM and voltage characteristics were examined in a testing macroscopic discharge cell of AC-PDP. On the basis of experimental analysis, the influence of oxide addition and deposition conditions on preferred orientations of Mg-Zr-O composite protective layers were investigated. The results showed that the preferred orientations of Mg-Zr-O films were determined by lattice distortion of MgO crystal. The deposition conditions have great effects on the preferred orientations of Mg-Zr-O films. The preferred orientations affect voltage characteristics through affecting surface morphology of Mg-Zr-O films. A small amount of Zr solution in MgO can decrease firing voltage compared with using pure MgO film. Firing voltage is closely related with the [ ZrO{2}/(MgO+ZrO{2})] ratio of evaporation source materials.

Spider texture and amphibole preferred orientations

NASA Astrophysics Data System (ADS)

Shelley, David

1994-05-01

Foliation in blueschist facies chert from California is defined by layers of oriented alkali-amphibole which consistently curve towards and converge on pyrite (and possibly pyrrhotite) crystals. These foliation nodes, not previously described, are called here 'spider texture'. The texture is interpreted in terms of perturbations of the stress field in a matrix undergoing strain about rigid pyrite (or pyrrhotite) crystals, and it has important implications for understanding the mechanisms of amphibole preferred orientation development. Geometrical relationships between spider texture, pressure shadows and quartz preferred orientations suggest that amphiboles grew with a strong preferred orientation along planes of maximum shearing stress. The mechanism of foliation and preferred orientation development probably involved competitive anisotropic growth of amphibole prisms within the small gaps that open at steps on shear planes, followed by additional (micro-) porphyroblastic growth. The first stage of the mechanism is similar to slickenfibre development.

Preferred crystallographic orientation in the ice I ← II transformation and the flow of ice II

USGS Publications Warehouse

Bennett, K.; Wenk, H.-R.; Durham, W.B.; Stern, L.A.; Kirby, S.H.

1997-01-01

The preferred crystallographic orientation developed during the ice I ← II transformation and during the plastic flow of ice II was measured in polycrystalline deuterium oxide (D2O) specimens using low-temperature neutron diffraction. Samples partially transformed from ice I to II under a non-hydrostatic stress developed a preferred crystallographic orientation in the ice II. Samples of pure ice II transformed from ice I under a hydrostatic stress and then when compressed axially, developed a strong preferred orientation of compression axes parallel to (1010). A match to the observed preferred orientation using the viscoplastic self-consistent theory was obtained only when (1010) [0001] was taken as the predominant slip system in ice II.

An Introduction to Object-Oriented Programming.

DTIC Science & Technology

1990-04-01

therefore it is an ot ject-oriented program and 7 are (sic) an c~ect-oriented programm.er" 3.1 "BUILT-IN" LANGUAGES Sprevously def nei, a b’:i1t-in languaje ...machines. 8 3.1.2 EIFFEL Eiffel [Meye87, Meye88a, Meye88b, Meye88c] was developed by Bertrand Meyer at Interactive Software Engineering Inc. It is a...is intended to serve as both a language and environment for designing software that is easily reusable and extendible. The notion of programming as

Well-isolated FePt grains with high coercivity on TiN underlayers for heat-assisted magnetic recording media

NASA Astrophysics Data System (ADS)

Santos, Tiffany; Jain, Shikha; Hirotsune, Akemi; Hellwig, Olav

2015-03-01

MgO is the underlayer material of choice for granular FePt thin film media for heat assisted magnetic recording, because MgO (001) seeds L10-ordered FePt with c-axis perpendicular to the film plane and high perpendicular magnetic anisotropy. MgO is also an effective diffusion barrier between the FePt grains and the metallic underlayers beneath the MgO. However, there are possible concerns associated with using MgO in the media structure. MgO is highly sensitive to moisture, and hydration of MgO could potentially degrade film properties. In addition, many particulates are incorporated into the film during the RF-sputter process, which can be sources of delamination, pinholes and damage to the low-flying recording heads. TiN is an attractive alternative to MgO because it is chemically and mechanically robust, and TiN can be DC-sputtered, which produces fewer particles and has a faster deposition rate. Even though TiN has the same rocksalt crystal structure and lattice constant as MgO, the higher surface energy of TiN causes more wetting of the FePt grains on the TiN surface. As a result, deposition of granular FePt on TiN most often produces inter-connected, worm-like grains with low coercivity. We will show that by optimizing the deposition of FePt and segregant material on the TiN underlayer, we are able to fabricate FePt media with well-isolated grains and high coercivity reaching nearly 4 Tesla. In addition, the FePt has excellent structural properties with a high degree of L10 atomic ordering and minimal c-axis in-plane oriented grains.

Subject Preference Regarding Three Psychotherapy Orientations.

ERIC Educational Resources Information Center

Hollis, Thomas G.

Research has shown that therapy preference affects both the quality of the initial therapy session and treatment outcome. To determine personality characteristics which would affect subjects' preference of therapeutic orientation and to obtain qualitative information about subjects' therapy preferences, 203 community college students indicated…

Form preferences in successive discrimination learning of young chicks.

PubMed

Zolman, J F; Pursley, D G; Hall, J A; Sahley, C L

1975-12-01

In four experiments the effects of form and orientation pecking preferences of 1- and 3-day old Vantress X Arbor Acre chicks on successive discrimination learning were determined, using heat reinforcement. Major findings were as follows: (a) The young chick has both circle and verticle orientation pecking preferences that are present during at least the first 3 days after hatching; (b) when either of these preferred cues is the nonreinforced cue, the young chick has difficulty in learning not to respond to it but learns quickly not to respond to an unpreferred cue (e.g., triangle and horizontal oriented dots or bar); and (c) these pecking preferences can be modified by heat reinforcement, and the effects of this conditioning is evidenct in subsequent extinction and retention tests. The main conclusion from these experiments is that form and orientation preferences, like brightness and color preferences, are important developmental constraints on conditioning of the young chick.

Fog water collection effectiveness: Mesh intercomparisons

USGS Publications Warehouse

Fernandez, Daniel; Torregrosa, Alicia; Weiss-Penzias, Peter; Zhang, Bong June; Sorensen, Deckard; Cohen, Robert; McKinley, Gareth; Kleingartner, Justin; Oliphant, Andrew; Bowman, Matthew

2018-01-01

To explore fog water harvesting potential in California, we conducted long-term measurements involving three types of mesh using standard fog collectors (SFC). Volumetric fog water measurements from SFCs and wind data were collected and recorded in 15-minute intervals over three summertime fog seasons (2014–2016) at four California sites. SFCs were deployed with: standard 1.00 m2 double-layer 35% shade coefficient Raschel; stainless steel mesh coated with the MIT-14 hydrophobic formulation; and FogHa-Tin, a German manufactured, 3-dimensional spacer fabric deployed in two orientations. Analysis of 3419 volumetric samples from all sites showed strong relationships between mesh efficiency and wind speed. Raschel mesh collected 160% more fog water than FogHa-Tin at wind speeds less than 1 m s–1 and 45% less for wind speeds greater than 5 m s–1. MIT-14 coated stainless-steel mesh collected more fog water than Raschel mesh at all wind speeds. At low wind speeds of < 1 m s–1 the coated stainless steel mesh collected 3% more and at wind speeds of 4–5 m s–1, it collected 41% more. FogHa-Tin collected 5% more fog water when the warp of the weave was oriented vertically, per manufacturer specification, than when the warp of the weave was oriented horizontally. Time series measurements of three distinct mesh across similar wind regimes revealed inconsistent lags in fog water collection and inconsistent performance. Since such differences occurred under similar wind-speed regimes, we conclude that other factors play important roles in mesh performance, including in-situ fog event and aerosol dynamics that affect droplet-size spectra and droplet-to-mesh surface interactions.

[Dynamics of tuning to orientation of cross-like figures in neurons from the cat visual cortex].

PubMed

Lazareva, N A; Tsutskiridze, D Iu; Shevelev, I A; Novikova, R V; Tikhomirov, A S; Sharaev, G A

2003-01-01

Dynamics of tuning to orientation of flashing light bar and to orientation of cross-like figure was studied by a temporal slices method in 87 neurons of the cat primary visual cortex. Tuning was plotted by spikes number in the entire response and in its successive fragments with a step of 20 ms. It was found that successive dynamic shift of preferred orientation of a bar was typical for 87% units, white such shift of preferred orientation of a cross was met in 75% of cases. Comparison of tuning dynamics for bar and cross allowed to separate units into three groups: the first one (58.6% of cases) with larger dynamic shift of a bar preferred orientation then of a cross (74.9 +/- 5.8 degrees [symbol: see text] 29.8 +/- 4.1 degrees, correspondingly, p < 0.00001), the second group (21.5%) with opposite effect (24.2 +/- 5.2 degrees and 69.2 +/- 10.0 degrees, p < 0.0002) and the third group (19.8%) without significant shift of preferred orientation of bar and cross and without difference in their dynamics. Possible mechanisms of the preferred orientation dynamics and its difference for bar and cross are discussed.

Late Triassic granites from Bangka, Indonesia: A continuation of the Main Range granite province of the South-East Asian Tin Belt

NASA Astrophysics Data System (ADS)

Ng, Samuel Wai-Pan; Whitehouse, Martin J.; Roselee, Muhammad H.; Teschner, Claudia; Murtadha, Sayed; Oliver, Grahame J. H.; Ghani, Azman A.; Chang, Su-Chin

2017-05-01

The South-East Asian Tin Belt is one of the most tin-productive regions in the world. It comprises three north-south oriented granite provinces, of which the arc-related Eastern granite province and the collision-related Main Range granite province run across Thailand, Singapore, and Indonesia. These tin-producing granite provinces with different mineral assemblages are separated by Paleo-Tethyan sutures exposed in Thailand and Malaysia. The Eastern Province is usually characterised by granites with biotite ± hornblende. Main Range granites are sometimes characterised by the presence of biotite ± muscovite. However, the physical boundary between the two types of granite is not well-defined on the Indonesian Tin Islands, because the Paleo-Tethyan suture is not exposed on land there. Both hornblende-bearing (previously interpreted as I-type) and hornblende-barren (previously interpreted as S-type) granites are apparently randomly distributed on the Indonesian Tin Islands. Granites exposed on Bangka, the largest and southernmost Tin Island, no matter whether they are hornblende-bearing or hornblende-barren, are geochemically similar to Malaysian Main Range granites. The average ɛNd(t) value obtained from the granites from Bangka (average ɛNd(t) = -8.2) falls within the range of the Main Range Province (-9.6 to -5.4). These granites have SIMS zircon U-Pb ages of ca. 225 Ma and ca. 220 Ma, respectively that are both within the period of Main Range magmatism (∼226-201 Ma) in the Peninsular Malaysia. We suggest that the granites exposed on Bangka represent the continuation of the Main Range Province, and that the Paleo-Tethyan suture lies to the east of the island.

Preference for sex of first child among women classified as androgynous and nonandrogynous.

PubMed

Marleau, J D; Berthiaume, M; Saucier, J F; David, H; Borgeat, F; Bernazzani, O

1998-02-01

This paper examined the relation between gender-role orientation and the preference for sex of firstborn child in 212 pregnant nulliparous women. The Bem Sex-role Inventory was used to assess gender-role orientation of participants. Analysis suggested that gender-role orientation, as measured does not effectively predict the preference for sex of firstborn child.

An experimental approach of decoupling Seebeck coefficient and electrical resistivity

NASA Astrophysics Data System (ADS)

Muhammed Sabeer N., A.; Paulson, Anju; Pradyumnan, P. P.

2018-04-01

The Thermoelectrics (TE) has drawn increased attention among renewable energy technologies. The performance of a thermoelectric material is quantified by a dimensionless thermoelectric figure of merit, ZT=S2σT/κ, where S and σ vary inversely each other. Thus, improvement in ZT is not an easy task. So, researchers have been trying different parameter variations during thin film processing to improve TE properties. In this work, tin nitride (Sn3N4) thin films were deposited on glass substrates by reactive RF magnetron sputtering and investigated its thermoelectric response. To decouple the covariance nature of Seebeck coefficient and electrical resistivity for the enhancement of power factor (S2σ), the nitrogen gas pressure during sputtering was reduced. Reduction in nitrogen gas pressure reduced both sputtering pressure and amount of nitrogen available for reaction during sputtering. This experimental approach of combined effect introduced preferred orientation and stoichiometric variations simultaneously in the sputtered Sn3N4 thin films. The scattering mechanism associated with these variations enhanced TE properties by independently drive the Seebeck coefficient and electrical resistivity parameters.

The influence of preferred orientation and poling temperature on the polarization switching current in PZT thin films

NASA Astrophysics Data System (ADS)

Xiao, Mi; Zhang, Weikang; Zhang, Zebin; Zhang, Ping; Lan, Kuibo

2017-07-01

In this paper, Pb(Zr0.52Ti0.48)O3 (PZT) thin films with different preferred orientation were prepared on platinized silicon substrates by a modified sol-gel method. Our results indicate that the polarization switching current in PZT thin films is dependent on preferred orientation and poling temperature. In our measurements, (111)-oriented PZT has a larger polarization switching current than randomly oriented PZT, and with the increase of the degree of (111) preferred orientation and the poling temperature, the polarization switching current gradually increase. Considering the contact of PZT thin film with electrodes, the space-charged limited conduction (SCLC) combined with domain switching mechanism may be responsible for such phenomena. By analyzing the conduction data, we found the interface-limited Schottky emission (ES) and bulk-limited Poole-Frenkel hopping (PF) are not suitable for our samples.

Preference bias of head orientation in choosing between two non-durables.

PubMed

Funaya, Hiroyuki; Shibata, Tomohiro

2015-01-01

The goal of this study is to investigate how customers' gaze, head and body orientations reflect their choices. Although the relationship between human choice and gaze behavior has been well-studied, other behaviors such as head and body are unknown. We conducted a two-alternatives-forced-choice task to examine (1) whether preference bias, i.e., a positional bias in gaze, head and body toward the item that was later chosen, exists in choice, (2) when preference bias is observed and when prediction of the resulting choice becomes possible (3) whether human choice is affected when the body orientations are manipulated. We used real non-durable products (cheap snacks and clothing) on a shopping shelf. The results showed that there was a significant preference bias in head orientation at the beginning 1 s when the subjects stood straight toward the shelf, and that the head orientation was more biased toward the selected item than the gaze and the center of pressure at the ending 1 s. Manipulating body orientation did not affect the result of choice. The preference bias detected by observing the head orientation would be useful in marketing science for predicting customers' choice.

Self-Other Orientations and the Edwards Personal Preference Schedule

ERIC Educational Resources Information Center

Santee, Richard T.

1975-01-01

A modified version of the Edwards Personal Preference Schedule (EPPS) was administered to measure self and other orientations on 15 personality variables. The respondents were shown to have different preferences for themselves than for others. (Author/DEP)

The electronic structure of oriented poly[2-methoxy-5-(2'-ethyl-hexyloxy)- 1,4-phenylene-vinylene

NASA Astrophysics Data System (ADS)

Chambers, D. K.; Karanam, S.; Qi, D.; Selmic, S.; Losovyj, Y. B.; Rosa, L. G.; Dowben, P. A.

2005-02-01

Poly[2-methoxy-5-(2’-ethyl-hexyloxy)-1,4-phenylene-vinylene] (MEH-PPV) adopts a preferential orientation on indium tin oxide. Although the basic building block of this polymer provides a negligible overall point-group symmetry, the polymer MEH-PPV packs with sufficient order to exhibit band structure. The polymer is fragile with bond cleavage evident following both argon-ion impact and ultraviolet radiation, but annealing leads to the restoration of much of the bond order.

Roughness of Ti Substrates for Control of the Preferred Orientation of TiO 2 Nanotube Arrays as a New Orientation Factor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seong, Won Mo; Kim, Dong Hoe; Park, Ik Jae

2015-06-11

We report the surface roughness of a Ti substrate as a critical factor for controlling the degree of the preferred orientation of anatase TiO2 nanotube arrays (NTAs) which are synthesized by anodization and a subsequent annealing process. The degree of the preferred orientation to the (004) plane of the anatase crystal structure has a strong dependency on the root-mean-square roughness (Sq) of the initial Ti substrate when the roughness-controlled substrates are anodized in an ethylene glycol-based electrolyte containing ~2 wt % of water. Highly preferred oriented NTAs were obtained from low-Sq (<10 nm) substrates, which were accompanied by uniform poremore » distribution and low concentration of hydroxyl ions in as-anodized amorphous NTAs. The mechanism of the preferred oriented crystallization of nanometer-scaled tube walls is explained considering the microscopic geometrical uniformity of the oxide barrier and nanopores at the early stage of anodization, which affected the local electric field and thus the insertion of the hydroxyl group into the amorphous TiO2 tube walls.« less

Effect of Si in reactively sputtered Ti-Si-N films on structure and diffusion barrier performance

NASA Astrophysics Data System (ADS)

Sun, X.; Kolawa, E.; Im, S.; Garland, C.; Nicolet, M.-A.

Two ternary films about 100 nm thick, Ti34Si23N43 (b3) and Ti35Si13N52 (c3), are synthesized by reactively sputtering a Ti5Si3 or a Ti3Si target, respectively. The silicon-lean film (c3) has a columnar structure closely resembling that of TiN. As a diffusion barrier between a shallow Si n+p junction diode and a Cu overlayer, this material is effective up to 700 °C for 30 min annealing in vacuum, a performance similar to that for TiN. The silicon-rich (b3) film contains nanocrystals of TiN, randomly oriented and embedded in an amorphous matrix. A film of (b3) maintains the stability of the same diode structure up to 850 °C for 30 min in vacuum. This film (b3) is clearly superior to TiN or to (c3). Similar experiments performed with Al instead of Cu overlayers highlight the importance of the thermodynamic stability of a barrier layer and demonstrate convincingly that for stable barriers the microstructure is a parameter that directly determines the barrier performance.

Multiple groups of orientation-selective visual mechanisms underlying rapid orientated-line detection.

PubMed Central

Foster, D H; Westland, S

1998-01-01

Visual search for an edge or line element differing in orientation from a background of other edge or line elements can be performed rapidly and effortlessly. In this study, based on psychophysical measurements with ten human observers, threshold values of the angle between a target and background line elements were obtained as functions of background-element orientation, in brief masked displays. A repeated-loess analysis of the threshold functions suggested the existence of several groups of orientation-selective mechanisms contributing to rapid orientated-line detection; specifically, coarse, intermediate and fine mechanisms with preferred orientations spaced at angles of approximately 90 degrees, 35 degrees, and 10 degrees-25 degrees, respectively. The preferred orientations of coarse and some intermediate mechanisms coincided with the vertical or horizontal of the frontoparallel plane, but the preferred orientations of fine mechanisms varied randomly from observer to observer, possibly reflecting individual variations in neuronal sampling characteristics. PMID:9753784

Three-dimensional visual feature representation in the primary visual cortex

PubMed Central

Tanaka, Shigeru; Moon, Chan-Hong; Fukuda, Mitsuhiro; Kim, Seong-Gi

2011-01-01

In the cat primary visual cortex, it is accepted that neurons optimally responding to similar stimulus orientations are clustered in a column extending from the superficial to deep layers. The cerebral cortex is, however, folded inside a skull, which makes gyri and fundi. The primary visual area of cats, area 17, is located on the fold of the cortex called the lateral gyrus. These facts raise the question of how to reconcile the tangential arrangement of the orientation columns with the curvature of the gyrus. In the present study, we show a possible configuration of feature representation in the visual cortex using a three-dimensional (3D) self-organization model. We took into account preferred orientation, preferred direction, ocular dominance and retinotopy, assuming isotropic interaction. We performed computer simulation only in the middle layer at the beginning and expanded the range of simulation gradually to other layers, which was found to be a unique method in the present model for obtaining orientation columns spanning all the layers in the flat cortex. Vertical columns of preferred orientations were found in the flat parts of the model cortex. On the other hand, in the curved parts, preferred orientations were represented in wedge-like columns rather than straight columns, and preferred directions were frequently reversed in the deeper layers. Singularities associated with orientation representation appeared as warped lines in the 3D model cortex. Direction reversal appeared on the sheets that were delimited by orientation-singularity lines. These structures emerged from the balance between periodic arrangements of preferred orientations and vertical alignment of same orientations. Our theoretical predictions about orientation representation were confirmed by multi-slice, high-resolution functional MRI in the cat visual cortex. We obtained a close agreement between theoretical predictions and experimental observations. The present study throws a doubt about the conventional columnar view of orientation representation, although more experimental data are needed. PMID:21724370

Three-dimensional visual feature representation in the primary visual cortex.

PubMed

Tanaka, Shigeru; Moon, Chan-Hong; Fukuda, Mitsuhiro; Kim, Seong-Gi

2011-12-01

In the cat primary visual cortex, it is accepted that neurons optimally responding to similar stimulus orientations are clustered in a column extending from the superficial to deep layers. The cerebral cortex is, however, folded inside a skull, which makes gyri and fundi. The primary visual area of cats, area 17, is located on the fold of the cortex called the lateral gyrus. These facts raise the question of how to reconcile the tangential arrangement of the orientation columns with the curvature of the gyrus. In the present study, we show a possible configuration of feature representation in the visual cortex using a three-dimensional (3D) self-organization model. We took into account preferred orientation, preferred direction, ocular dominance and retinotopy, assuming isotropic interaction. We performed computer simulation only in the middle layer at the beginning and expanded the range of simulation gradually to other layers, which was found to be a unique method in the present model for obtaining orientation columns spanning all the layers in the flat cortex. Vertical columns of preferred orientations were found in the flat parts of the model cortex. On the other hand, in the curved parts, preferred orientations were represented in wedge-like columns rather than straight columns, and preferred directions were frequently reversed in the deeper layers. Singularities associated with orientation representation appeared as warped lines in the 3D model cortex. Direction reversal appeared on the sheets that were delimited by orientation-singularity lines. These structures emerged from the balance between periodic arrangements of preferred orientations and vertical alignment of the same orientations. Our theoretical predictions about orientation representation were confirmed by multi-slice, high-resolution functional MRI in the cat visual cortex. We obtained a close agreement between theoretical predictions and experimental observations. The present study throws a doubt about the conventional columnar view of orientation representation, although more experimental data are needed. Copyright © 2011 Elsevier Ltd. All rights reserved.

Improvement of Transparent Conducting Performance on Oxygen-Activated Fluorine-Doped Tin Oxide Electrodes Formed by Horizontal Ultrasonic Spray Pyrolysis Deposition.

PubMed

Koo, Bon-Ryul; Oh, Dong-Hyeun; Riu, Doh-Hyung; Ahn, Hyo-Jin

2017-12-27

In this study, highly transparent conducting fluorine-doped tin oxide (FTO) electrodes were fabricated using the horizontal ultrasonic spray pyrolysis deposition. In order to improve their transparent conducting performances, we carried out oxygen activation by adjusting the ratio of O 2 /(O 2 +N 2 ) in the carrier gas (0%, 20%, and 50%) used during the deposition process. The oxygen activation on the FTO electrodes accelerated the substitution concentration of F (F O • ) into the oxygen sites in the FTO electrode while the oxygen vacancy (V O • • ) concentration was reduced. In addition, due to growth of pyramid-shaped crystallites with (200) preferred orientations, this oxygen activation caused the formation of a uniform surface structure. As a result, compared to others, the FTO electrode prepared at 50% O 2 showed excellent electrical and optical properties (sheet resistance of ∼4.0 ± 0.14 Ω/□, optical transmittance of ∼85.3%, and figure of merit of ∼5.09 ± 0.19 × 10 -2 Ω -1 ). This led to a superb photoconversion efficiency (∼7.03 ± 0.20%) as a result of the improved short-circuit current density. The photovoltaic performance improvement can be defined by the decreased sheet resistance of FTO used as a transparent conducting electrode in dye-sensitized solar cells (DSSCs), which is due to the combined effect of the high carrier concentration by the improved F O • concentration on the FTO electrodes and the fasted Hall mobility by the formation of a uniform FTO surface structure and distortion relaxation on the FTO lattices resulting from the reduced V O • • • concentration.

Physicochemical characterization of point defects in fluorine doped tin oxide films

NASA Astrophysics Data System (ADS)

Akkad, Fikry El; Joseph, Sudeep

2012-07-01

The physical and chemical properties of spray deposited FTO films are studied using FESEM, x-ray diffraction (XRD), x-ray photoelectron spectroscopy (XPS), electrical and optical measurements. The results of XRD measurements showed that the films are polycrystalline (grain size 20-50 nm) with Rutile structure and mixed preferred orientation along the (200) and (110) planes. An angular shift of the XRD peaks after F-doping is observed and interpreted as being due to the formation of substitutional fluorine defects (FO) in presence of high concentration of oxygen vacancies (VO) that are electrically neutral. The electrical neutrality of oxygen vacancies is supported by the observation that the electron concentration n is two orders of magnitude lower than the VO concentration calculated from chemical analyses using XPS measurements. It is shown that an agreement between XPS, XRD, and Hall effect results is possible provided that the degree of deviation from stoichiometry is calculated with the assumption that the major part of the bulk carbon content is involved in O-C bonds. High temperature thermal annealing is found to cause an increase in the FO concentration and a decrease in both n and VO concentrations with the increase of the annealing temperature. These results could be interpreted in terms of a high temperature chemical exchange reaction between the SnO2 matrix and a precipitated fluoride phase. In this reaction, fluorine is released to the matrix and Sn is trapped by the fluoride phase, thus creating substitutional fluorine FO and tin vacancy VSn defects. The enthalpy of this reaction is determined to be approximately 2.4 eV while the energy of formation of a VSn through the migration of SnSn host atom to the fluoride phase is approximately 0.45 eV.

Electron microscopic and ion scattering studies of heteroepitaxial tin-doped indium oxide films

NASA Astrophysics Data System (ADS)

Kamei, Masayuki; Shigesato, Yuzo; Takaki, Satoru; Hayashi, Yasuo; Sasaki, Mikio; Haynes, Tony E.

1994-08-01

The microstructure of heteroepitaxial tin-doped indium oxide (ITO) films were studied in detail. The surface morphology of the heteroepitaxial ITO film consisted of square-shaped, in-plane oriented subgrains (˜300 Å) in contrast to that of the polycrystalline film (characteristic grain-subgrain structure). The subgrain boundaries were predominantly formed along the {110} planes in the ITO film and dislocations were observed primarily along the subgrain boundaries. Ion channeling measurements showed the dislocation density of this film to be approximately 3×1010/cm2, and the angular distribution of the ion channeling yield showed that the subgrains are aligned to within better than 0.3° (standard deviation).

Convection of tin in a Bridgman system. I - Flow characterization by effective diffusivity measurements

NASA Technical Reports Server (NTRS)

Sears, B.; Narayanan, R.; Anderson, T. J.; Fripp, A. L.

1992-01-01

An electrochemical titration method was used to investigate the dynamic states in a cylindrical layer of convecting tin. The liquid tin was contained in a cell, with curved boundaries made of quartz and flat boundaries made of a solid state electrolyte - yttria-stabilized zirconia (YSZ). The electrolyte acted as a window through which a trace amount of oxygen could be pumped in or out by the application of a constant voltage. The concentration at the YSZ interface was monitored by operating the electrochemical cell in the galvanic mode. Experimentally determined effective diffusivities of oxygen were compared with the molecular diffusivity. Dynamic states in the convective flow were thus inferred. Temperature measurements were simultaneously made in order to identify the onset of oscillations from a steady convective regime. The experiments were conducted for two different aspect ratios for various imposed temperature gradients and two different orientations with respect to gravity. Transcritical states were identified and comparison to two-dimensional numerical models were made.

An object-oriented framework for distributed hydrologic and geomorphic modeling using triangulated irregular networks

NASA Astrophysics Data System (ADS)

Tucker, Gregory E.; Lancaster, Stephen T.; Gasparini, Nicole M.; Bras, Rafael L.; Rybarczyk, Scott M.

2001-10-01

We describe a new set of data structures and algorithms for dynamic terrain modeling using a triangulated irregular network (TINs). The framework provides an efficient method for storing, accessing, and updating a Delaunay triangulation and its associated Voronoi diagram. The basic data structure consists of three interconnected data objects: triangles, nodes, and directed edges. Encapsulating each of these geometric elements within a data object makes it possible to essentially decouple the TIN representation from the modeling applications that make use of it. Both the triangulation and its corresponding Voronoi diagram can be rapidly retrieved or updated, making these methods well suited to adaptive remeshing schemes. We develop a set of algorithms for defining drainage networks and identifying closed depressions (e.g., lakes) for hydrologic and geomorphic modeling applications. We also outline simple numerical algorithms for solving network routing and 2D transport equations within the TIN framework. The methods are illustrated with two example applications, a landscape evolution model and a distributed rainfall-runoff model.

Investigation of the Relationships Between Personality Types of Eighth-Grade Science Students and Cognitive Preference Orientation.

ERIC Educational Resources Information Center

Novak, John Anthony

This study investigated the relationship among personality types, cognitive preference orientation, science achievement, intelligence, attitudes toward science and scientists, sex, and geographic area of eighth-grade science students using the following four instruments: (1) Myers-Briggs Type Indication (MBTI); (2) Cognitive Preference Examination…

Method and apparatus for coating substrates using a laser

NASA Technical Reports Server (NTRS)

Zaplatynsky, I. (Inventor)

1984-01-01

Metal substrates, preferably of titanium and titanium alloys, are coated by alloying or forming TiN on a substrate surface. A laser beam strikes the surface of a moving substrate in the presence of purified nitrogen gas. A small area of the substrate surface is quickly heated without melting. This heated area reacts with the nitrogen to form a solid solution. The alloying or formation of TiN occurs by diffusion of nitrogen into the titanium. Only the surface layer of the substrate is heated because of the high power density of the laser beam and short exposure time. The bulk of the substrate is not affected, and melting of the substrate is avoided because it would be detrimental.

Formation of hydrothermal tin deposits: Raman spectroscopic evidence for an important role of aqueous Sn(IV) species

NASA Astrophysics Data System (ADS)

Schmidt, Christian

2018-01-01

The speciation of tin and the solubility of cassiterite in H2O + HCl were determined at temperatures to 600 °C using in situ Raman spectroscopy. In addition, information on the fluid-melt partition of Sn was obtained at 700 °C and indicated a preference of the fluid only at HCl concentrations that are much higher than in fluids exsolved from natural felsic melts. Dissolution of cassiterite generally resulted in formation of Sn(IV) species unless reduced conditions were generated by hydrogen permeation or carbohydrates in the starting material. The prevalent aqueous Sn(IV) species was [SnCl4(H2O)2]0, with additional [SnCl3(H2O)3]+ and [SnCl5(H2O)]-. The only detectable Sn(II) species was very likely [Sn(II)Cl3]-. Cassiterite solubility increased with HCl concentration and was generally high in H2O+HCl fluids, with no strong dependencies on temperature, pressure, or the oxidation state of tin in the fluid. The Sn(IV) concentrations at 500 and 600 °C determined from the integrated ν1[Sn(IV)sbnd Cl] band intensity are in good agreement with literature data on the cassiterite solubility in H2O + HCl at oxygen fugacities along the hematite-magnetite buffer. The combined results from previous experimental studies and this study demonstrate that HCl molality is a crucial parameter for hydrothermal mobilization and transport of tin and for cassiterite precipitation, and that pH, pressure and temperature are less important. Current models on hydrothermal tin deposit formation need to be augmented to include Sn(IV)sbnd Cl complexes as significant tin-transporting species. Irrespective of the oxidation state of tin in the fluid, cassiterite precipitates due to reaction of the hydrothermal fluid with the wall rock (greisen or skarn formation), dilution (mixing with meteoric water) or a decrease in the HCl activity in the aqueous liquid by boiling. A redox reaction is only required for tin transported as Sn(II) to be converted to Sn(IV).

Left and right brain-oriented hemisity subjects show opposite behavioral preferences.

PubMed

Morton, Bruce E

2012-01-01

Recently, three independent, intercorrelated biophysical measures have provided the first quantitative measures of a binary form of behavioral laterality called "Hemisity," a term referring to inherent opposite right or left brain-oriented differences in thinking and behavioral styles. Crucially, the right or left brain-orientation of individuals assessed by these methods was later found to be essentially congruent with the thicker side of their ventral gyrus of the anterior cingulate cortex (vgACC) as revealed by a 3 min MRI procedure. Laterality of this putative executive structural element has thus become the primary standard defining individual hemisity. Here, the behavior of 150 subjects, whose hemisity had been calibrated by MRI, was assessed using five MRI-calibrated preference questionnaires, two of which were new. Right and left brain-oriented subjects selected opposite answers (p > 0.05) for 47 of the 107 "either-or," forced choice type preference questionnaire items. The resulting 30 hemisity subtype preference differences were present in several areas. These were: (1) in logical orientation, (2) in type of consciousness, (3) in fear level and sensitivity, (4) in social-professional orientation, and (5) in pair bonding-spousal dominance style. The right and left brain-oriented hemisity subtype subjects, sorted on the anatomical basis of upon which brain side their vgACC was thickest, showed 30 significant differences in their "either-or" type of behavioral preferences.

The relation between gender role orientation and fear and anxiety in nonclinic-referred children.

PubMed

Muris, Peter; Meesters, Cor; Knoops, Miranda

2005-06-01

This study examined the relation between gender role orientation and fear and anxiety in a sample of nonclinic-referred children (N = 209) ages 10 to 13 years. Children and their parents completed questionnaires assessing children's gender role orientation, toy and activity preferences, and fear and anxiety. Results generally indicated that femininity and a preference for girls' toys and activities were positively associated with fear and anxiety, whereas masculinity and a preference for boys' toys and activities were negatively related to these emotions. Furthermore, gender role orientation accounted for more of the variance in fear and anxiety scores than the child's sex.

Ductile alloy and process for preparing composite superconducting wire

DOEpatents

Verhoeven, John D.; Finnemore, Douglas K.; Gibson, Edwin D.; Ostenson, Jerome E.

1983-03-29

An alloy for the commercial production of ductile superconducting wire is prepared by melting together copper and at least 15 weight percent niobium under non-oxygen-contaminating conditions, and rapidly cooling the melt to form a ductile composite consisting of discrete, randomly distributed and orientated dendritic-shaped particles of niobium in a copper matrix. As the wire is worked, the dendritric particles are realigned parallel to the longitudinal axis and when drawn form a plurality of very fine ductile superconductors in a ductile copper matrix. The drawn wire may be tin coated and wound into magnets or the like before diffusing the tin into the wire to react with the niobium. Impurities such as aluminum or gallium may be added to improve upper critical field characteristics.

Ductile alloy and process for preparing composite superconducting wire

DOEpatents

Verhoeven, J.D.; Finnemore, D.K.; Gibson, E.D.; Ostenson, J.E.

An alloy for the commercial production of ductile superconducting wire is prepared by melting together copper and at least 15 weight percent niobium under non-oxygen-contaminating conditions, and rapidly cooling the melt to form a ductile composite consisting of discrete, randomly distributed and oriented dendritic-shaped particles of niobium in a copper matrix. As the wire is worked, the dendritic particles are realigned parallel to the longitudinal axis and when drawn form a plurality of very fine ductile superconductors in a ductile copper matrix. The drawn wire may be tin coated and wound into magnets or the like before diffusing the tin into the wire to react with the niobium. Impurities such as aluminum or gallium may be added to improve upper critical field characteristics.

Synthesis and characterisation of co-evaporated tin sulphide thin films

NASA Astrophysics Data System (ADS)

Koteeswara Reddy, N.; Ramesh, K.; Ganesan, R.; Ramakrishna Reddy, K. T.; Gunasekhar, K. R.; Gopal, E. S. R.

2006-04-01

Tin sulphide films were grown at different substrate temperatures by a thermal co-evaporation technique. The crystallinity of the films was evaluated from X-ray diffraction studies. Single-phase SnS films showed a strong (040) orientation with an orthorhombic crystal structure and a grain size of 0.12 μm. The films showed an electrical resistivity of 6.1 Ω cm with an activation energy of 0.26 eV. These films exhibited an optical band gap of 1.37 eV and had a high optical absorption coefficient (>104 cm-1) above the band-gap energy. The results obtained were analysed to evaluate the potentiality of the co-evaporated SnS films as an absorber layer in solar photovoltaic devices.

Texture inheritance from austenite to 7 M martensite in Ni-Mn-Ga melt-spun ribbons

NASA Astrophysics Data System (ADS)

Li, Zongbin; Jiang, Yiwen; Li, Zhenzhuang; Yang, Yiqiao; Yang, Bo; Zhang, Yudong; Esling, Claude; Zhao, Xiang; Zuo, Liang

In this work, Ni53Mn22Ga25 and Ni51Mn27Ga22 ribbons with austenite and 7 M martensite at room temperature respectively, were prepared by melt-spinning. Through the detailed crystallographic analyses, the preferred orientation in ribbons was confirmed. It is shown that the austenite in Ni53Mn22Ga25 ribbons forms a preferred orientation with {4 0 0}A in parallel to ribbon plane, whereas the 7 M martensite in Ni51Mn27Ga22 ribbons develops the preferred orientation with {2 0 -20}7M, {2 0 20}7M, and {0 4 0}7M crystallographic planes parallel to the ribbon plane. Since {2 0 -20}7M, {2 0 20}7M, and {0 4 0}7M are originated from {4 0 0}A, the preferred orientation in ribbons thus can be inherited after the martensitic transformation. Such texture inheritance is attributed to the intrinsic orientation relationship between austenite and 7 M martensite.

Design and test of an object-oriented GIS to map plant species in the Southern Rockies

NASA Technical Reports Server (NTRS)

Morain, Stanley A.; Neville, Paul R. H.; Budge, Thomas K.; Morrison, Susan C.; Helfrich, Donald A.; Fruit, Sarah

1993-01-01

Elevational and latitudinal shifts occur in the flora of the Rocky Mountains due to long term climate change. In order to specify which species are successfully migrating with these changes, and which are not, an object-oriented, image-based geographic information system (GIS) is being created to animate evolving ecological regimes of temperature and precipitation. Research at the Earth Data Analysis Center (EDAC) is developing a landscape model that includes the spatial, spectral and temporal domains. It is designed to visualize migratory changes in the Rocky Mountain flora, and to specify future community compositions. The object-oriented database will eventually tag each of the nearly 6000 species with a unique hue, intensity, and saturation value, so their movements can be individually traced. An associated GIS includes environmental parameters that control the distribution of each species in the landscape, and satellite imagery is used to help visualize the terrain. Polygons for the GIS are delineated as landform facets that are static in ecological time. The model manages these facets as a triangular irregular net (TIN), and their analysis assesses the gradual progression of species as they migrate through the TIN. Using an appropriate climate change model, the goal will be to stop the modeling process to assess both the rate and direction of species' change and to specify the changing community composition of each landscape facet.

Preferences for a patient-centered role orientation: association with patient-information-seeking behavior and clinical markers of health.

PubMed

Baldwin, Austin S; Cvengros, Jamie A; Christensen, Alan J; Ishani, Areef; Kaboli, Peter J

2008-02-01

Few data exist examining how patients' preferred role orientation (patient-centered or provider-centered) is associated with "patient-centered" behavior and clinical markers of health. The purpose of the study is to investigate how patients' preferred role orientation is associated with information-seeking behavior and clinical markers of health in a chronically ill population. Participants were 189 hypertensive patients, at two VA Medical Centers and four community-based clinics, who completed measures of preferred role orientation and medication information seeking. Lab values of patients' blood pressure, LDL cholesterol, and glycosylated hemoglobin A1c were used as clinical markers. Preference for a patient-centered role was associated with seeking medication information from various sources (e.g., the internet [OR = 1.14, 95% CI = 1.05-1.23]) and with the number of sources from which patients obtained information (beta = .21, p = 0.005). However, patient-centered preferences were also associated with higher systolic blood pressure (beta = 0.16, p = 0.04), higher diastolic blood pressure (beta = .15, p = 0.04), and higher LDL cholesterol (beta = 0.17, p = 0.04). There was no association with glycosylated hemoglobin A1c (beta = -0.10, p = 0.36). Patients who preferred a patient-centered role engaged in behavior consistent with their preferences, but had higher blood pressure and less favorable lipid levels. These findings are discussed in terms of the nature and treatment of certain chronic conditions that may explain why a patient-centered role orientation is associated with a less favorable clinical profile in some contexts.

Employee Perceptions of an Organization's Learning Climate: Effects of Employee Orientation Training

ERIC Educational Resources Information Center

Akdere, Mesut; Schmidt, Steven W.

2008-01-01

The most important goal of any given training effort is to achieve learning at the individual, group/team, and organizational levels. This study used a repeated measures design to measure the change in employee perception of an organization's learning environment tin a large U.S. manufacturing company. The time period examined included an employee…

Effect of S-doping on structural, optical and electrochemical properties of vanadium oxide thin films prepared by spray pyrolysis

NASA Astrophysics Data System (ADS)

Mousavi, M.; Kompany, A.; Shahtahmasebi, N.; Bagheri-Mohagheghi, M.-M.

2013-12-01

In this research, S-doped vanadium oxide thin films, with doping levels from 0 to 40 at.%, are prepared by spray pyrolysis technique on glass substrates. For electrochemical measurements, the films were deposited on florin-tin oxide coated glass substrates. The effect of S-doping on structural, electrical, optical and electrochemical properties of vanadium oxide thin films was studied. The x-ray diffractometer analysis indicated that most of the samples have cubic β-V2O5 phase structure with preferred orientation along [200]. With increase in the doping levels, the structure of the samples tends to be amorphous. The scanning electron microscopy images show that the structure of the samples is nanobelt-shaped and the width of the nanobelts decreases from nearly 100 to 40 nm with increase in the S concentration. With increase in the S-doping level, the sheet resistance and the optical band gap increase from 940 to 4015 kΩ/square and 2.41 to 2.7 eV, respectively. The cyclic voltammogram results obtained for different samples show that the undoped sample is expanded and the sample prepared at 20 at.% S-doping level has sharper anodic and cathodic peaks.

Growth and Characterization of the Evaporated Quaternary Absorber Cu2FeSnS4 for Solar Cell Applications

NASA Astrophysics Data System (ADS)

Oueslati, Hiba; Ben Rabeh, Mohamed; Kanzari, Mounir

2018-03-01

Cu2FeSnS4 (CFTS) was synthesized by direct fusion of high-purity elemental copper, iron, tin and sulfur. CFTS thin films were deposited on glass substrates heated by single source vacuum thermal evaporation, after which the obtained samples were annealed under a sulfur atmosphere in a sealed quartz tube at 400°C for 1 h in order to optimize the CFTS stannite phase. The substrate temperature was varied from room temperature to 200°C. The formation of a stannite structure with (112), (200) and (004) planes in the powder and thin films was confirmed using x-ray diffraction measurements and the crystallites were found to have a preferred orientation along the (112) direction. Optical measurements analysis showed that after the sulfurization process the layers have a relatively high absorption coefficient close to 105 cm-1 in the visible spectrum. The films show a direct optical band gap in the range 1.30-1.63 eV for substrate temperature varied from room temperature to 200°C. All samples revealed p-type conductivity as determined by the hot probe method.

fMRI orientation decoding in V1 does not require global maps or globally coherent orientation stimuli.

PubMed

Alink, Arjen; Krugliak, Alexandra; Walther, Alexander; Kriegeskorte, Nikolaus

2013-01-01

The orientation of a large grating can be decoded from V1 functional magnetic resonance imaging (fMRI) data, even at low resolution (3-mm isotropic voxels). This finding has suggested that columnar-level neuronal information might be accessible to fMRI at 3T. However, orientation decodability might alternatively arise from global orientation-preference maps. Such global maps across V1 could result from bottom-up processing, if the preferences of V1 neurons were biased toward particular orientations (e.g., radial from fixation, or cardinal, i.e., vertical or horizontal). Global maps could also arise from local recurrent or top-down processing, reflecting pre-attentive perceptual grouping, attention spreading, or predictive coding of global form. Here we investigate whether fMRI orientation decoding with 2-mm voxels requires (a) globally coherent orientation stimuli and/or (b) global-scale patterns of V1 activity. We used opposite-orientation gratings (balanced about the cardinal orientations) and spirals (balanced about the radial orientation), along with novel patch-swapped variants of these stimuli. The two stimuli of a patch-swapped pair have opposite orientations everywhere (like their globally coherent parent stimuli). However, the two stimuli appear globally similar, a patchwork of opposite orientations. We find that all stimulus pairs are robustly decodable, demonstrating that fMRI orientation decoding does not require globally coherent orientation stimuli. Furthermore, decoding remained robust after spatial high-pass filtering for all stimuli, showing that fine-grained components of the fMRI patterns reflect visual orientations. Consistent with previous studies, we found evidence for global radial and vertical preference maps in V1. However, these were weak or absent for patch-swapped stimuli, suggesting that global preference maps depend on globally coherent orientations and might arise through recurrent or top-down processes related to the perception of global form.

Method of preparing doped oxide catalysts for lean NOx exhaust

DOEpatents

Park, Paul W.

2004-03-09

The lean NOx catalyst includes a substrate, an oxide support material, preferably .gamma.-alumina deposited on the substrate and a metal or metal oxide promoter or dopant introduced into the oxide support material. The metal promoters or dopants are selected from the group consisting of indium, gallium, tin, silver, germanium, gold, nickel, cobalt, copper, iron, manganese, molybdenum, chromium cerium, and vanadium, and oxides thereof, and any combinations thereof. The .gamma.-alumina preferably has a pore volume of from about 0.5 to about 2.0 cc/g; a surface area of between 80 and 350 m.sup.2 /g; an average pore size diameter of between about 3 to 30 nm; and an impurity level of less than or equal to about 0.2 weight percent. In a preferred embodiment the .gamma.-alumina is prepared by a sol-gel method, with the metal doping of the .gamma.-alumina preferably accomplished using an incipient wetness impregnation technique.

Orientation control and domain structure analysis of {100}-oriented epitaxial ferroelectric orthorhombic HfO{sub 2}-based thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katayama, Kiliha; Shimizu, Takao; Sakata, Osami

2016-04-07

Orientation control of {100}-oriented epitaxial orthorhombic 0.07YO{sub 1.5}-0.93HfO{sub 2} films grown by pulsed laser deposition was investigated. To achieve in-plane lattice matching, indium tin oxide (ITO) and yttria-stabilized zirconia (YSZ) were selected as underlying layers. We obtained (100)- and (001)/(010)-oriented films on ITO and YSZ, respectively. Ferroelastic domain formation was confirmed for both films by X-ray diffraction using the superlattice diffraction that appeared only for the orthorhombic symmetry. The formation of ferroelastic domains is believed to be induced by the tetragonal–orthorhombic phase transition upon cooling the films after deposition. The present results demonstrate that the orientation of HfO{sub 2}-based ferroelectricmore » films can be controlled in the same manner as that of ferroelectric films composed of conventional perovskite-type material such as Pb(Zr, Ti)O{sub 3} and BiFeO{sub 3}.« less

Orientations of linear stone arrangements in New South Wales

NASA Astrophysics Data System (ADS)

Hamacher, Duane W.; Fuller, Robert S.; Norris, Ray P.

2012-12-01

We test the hypothesis that Aboriginal linear stone arrangements in New South Wales (NSW) are oriented to cardinal directions. We accomplish this by measuring the azimuths of stone arrangements described in site cards from the NSW Aboriginal Heritage Information Management System. We then survey a subset of these sites to test the accuracy of information recorded on the site cards. We find a preference recorded in the site cards for cardinal orientations among azimuths. The field surveys show that the site cards are reasonably accurate, but the surveyors probably did not correct for magnetic declinations. Using Monte Carlo statistics, we show that these preferred orientations did not occur by chance and that Aboriginal people deliberately aligned these arrangements to the approximate cardinal directions. We briefly explore possible reasons for these preferred orientations and highlight the need for future work.

Three-quarter views are subjectively good because object orientation is uncertain.

PubMed

Niimi, Ryosuke; Yokosawa, Kazuhiko

2009-04-01

Because the objects that surround us are three-dimensional, their appearance and our visual perception of them change depending on an object's orientation relative to a viewpoint. One of the most remarkable effects of object orientation is that viewers prefer three-quarter views over others, such as front and back, but the exact source of this preference has not been firmly established. We show that object orientation perception of the three-quarter view is relatively imprecise and that this impreciseness is related to preference for this view. Human vision is largely insensitive to variations among different three-quarter views (e.g., 45 degrees vs. 50 degrees ); therefore, the three-quarter view is perceived as if it corresponds to a wide range of orientations. In other words, it functions as the typical representation of the object.

Polymorphic Nature of Iron and Degree of Lattice Preferred Orientation Beneath the Earth's Inner Core Boundary

NASA Astrophysics Data System (ADS)

Mattesini, Maurizio; Belonoshko, Anatoly B.; Tkalčić, Hrvoje

2018-01-01

Deciphering the polymorphic nature and the degree of iron lattice-preferred orientation in the Earth's inner core holds a key to understanding the present status and evolution of the inner core. A multiphase lattice-preferred orientation pattern is obtained for the top 350 km of the inner core by means of the ab initio based Candy Wrapper Velocity Model coupled to a Monte Carlo phase discrimination scheme. The achieved geographic distribution of lattice alignment is characterized by two regions of freezing, namely within South America and the Western Central Pacific, that exhibit an uncommon high degree of lattice orientation. In contrast, widespread regions of melting of relatively weak lattice ordering permeate the rest of the inner core. The obtained multiphase lattice-preferred orientation pattern is in line with mantle-constrained geodynamo simulations and allows to setup an ad hoc mineral physics scenario for the complex Earth's inner core. It is found that the cubic phase of iron is the dominating iron polymorph in the outermost part of the inner core.

Mentoring Women in STEM: A Collegiate Investigation of Mentors and Proteges

NASA Astrophysics Data System (ADS)

Leavey, Nicole

Science, technology, engineering and mathematics (STEM) education in the United States lags behind that of other industrialized nations. Despite national efforts to enhance the quality of STEM education for students, progress remains elusive. Underperformance is evident in measures of outcomes, participation, and retention. In particular, inequity persists in the attraction and retention of women to STEM fields. Mentoring is heavily cited as a means to improve our national efforts to fortify STEM education. This research explores mentoring styles, gender preferences, and differential impact on outcomes. The results challenge conventional wisdom that women prefer and benefit from a style of mentoring that is different from the preferred style of men. This study found that male and female proteges do not desire different types of mentoring. In fact, male and female proteges desire task-oriented mentoring when compared to relationship-oriented mentoring styles. However, female proteges prefer to be mentored by female mentors and male proteges prefer to be mentored by male mentors. In addition, with respect to gender, mentors do not differ in the type of mentoring they employ. Additionally, results of the study indicate that task-oriented mentoring style may bring incremental explanatory power with regard to intention to pursue STEM careers. This research implicates STEM program design in university settings. Gender-focused STEM programs are advised to focus on preferences and mentoring type, but not in the conventional way. This research indicates that women in STEM disciplines are not expressing a preference for relationship-oriented mentoring type and do benefit from task-oriented mentoring styles.

[Temporal orientation and a course of alcohol addiction therapy].

PubMed

Chodkiewicz, Jan; Nowakowska, Katarzyna

2011-01-01

The aim of the study was assess the meaning of preferred temporal orientation for results of alcohol dependence therapy. One hundred and sixteen (116) (95 men and 21 women) alcohol addict patients were evaluated at the beginning of the alcohol addiction outpatient therapy. The temporal orientation and attitude for time was assessed by using Temporal Orientation Questionnaire-AION and Carpe Diem, Fatalism and Hedonism Scale by Sobol-Kwapinska. The results showed that alcohol addict patients were in the highest degree focused on the past and the present in the hedonism and fatalism dimensions, while being relatively focused in the lowest degree on the present carpe diem dimension and the future at the beginning of the therapy. Men and women at the beginning of the therapy varied in some dimensions of temporal orientation. The differences occurred also between patients who finished and discontinued alcohol dependence therapy. Patients at the begging of alcohol addiction therapy prefer past and present temporal orientation. 1. There are differences between temporal orientation preferred by men and women. 2. Future temporal orientation is beneficial to finish addiction therapy by addict men. 3. Women who finish therapy are focused more on the past and hedonistic present orientation than women who discontinued therapy.

Highly conducting and crystalline doubly doped tin oxide films fabricated using a low-cost and simplified spray technique

NASA Astrophysics Data System (ADS)

Ravichandran, K.; Muruganantham, G.; Sakthivel, B.

2009-11-01

Doubly doped (simultaneous doping of antimony and fluorine) tin oxide films (SnO 2:Sb:F) have been fabricated by employing an inexpensive and simplified spray technique using perfume atomizer from aqueous solution of SnCl 2 precursor. The structural studies revealed that the films are highly crystalline in nature with preferential orientation along the (2 0 0) plane. It is found that the size of the crystallites of the doubly doped tin oxide films is larger (69 nm) than that (27 nm) of their undoped counterparts. The dislocation density of the doubly doped film is lesser (2.08×10 14 lines/m 2) when compared with that of the undoped film (13.2×10 14 lines/m 2), indicating the higher degree of crystallinity of the doubly doped films. The SEM images depict that the films are homogeneous and uniform. The optical transmittance in the visible range and the optical band gap of the doubly doped films are 71% and 3.56 eV respectively. The sheet resistance (4.13 Ω/□) attained for the doubly doped film in this study is lower than the values reported for spray deposited fluorine or antimony doped tin oxide films prepared from aqueous solution of SnCl 2 precursor (without using methanol or ethanol).

Properties of Semiconductors: Synthesis of Oriented ZnO for Photoelectrochemistry and Photoremediation

ERIC Educational Resources Information Center

Koenig, Emma; Jacobs, Ari; Lisensky, George

2017-01-01

Semiconductors are an important class of materials; preparing ZnO nanorods allows semiconducting properties to be easily observed. The week before lab, groups of four students take 15 min to setup two fluorine-doped tin oxide glass (FTO) slides in a zinc nitrate and hexamethylenetetramine solution stored at 90°C until the next lab. Hexagonal ZnO…

Career Orientations and Career Route Preferences in R&D Organisations.

ERIC Educational Resources Information Center

Petroni, Alberto

2000-01-01

A survey of 151 Italian scientists and engineers and case studies of a career development system for technical professionals revealed that career orientation (as measured by Schein's career anchors) is a useful predictor of career route preferences. (Author/JOW)

Development of chemically vapor deposited rhenium emitters of (0001) preferred crystal orientation

NASA Technical Reports Server (NTRS)

Yang, L.; Hudson, R. G.

1973-01-01

Rhenium thermionic emitters were prepared by the pyrolysis of rhenium chlorides formed by the chlorination of rhenium pellets. The impurity contents, microstructures, degrees of (0001) preferred crystal orientation, and vacuum electron work functions of these emitters were determined as a function of deposition parameters, such as substrate temperature, rhenium pellet temperature and chlorine flow rate. A correlation between vacuum electron work function and degree of (0001) preferred crystal orientation was established. Conditions for depositing porosity-free rhenium emitters of high vacuum electron work functions were defined. Finally, three cylindrical rhenium emitters were prepared under the optimum deposition conditions.

How shared preferences in music create bonds between people: values as the missing link.

PubMed

Boer, Diana; Fischer, Ronald; Strack, Micha; Bond, Michael H; Lo, Eva; Lam, Jason

2011-09-01

How can shared music preferences create social bonds between people? A process model is developed in which music preferences as value-expressive attitudes create social bonds via conveyed value similarity. The musical bonding model links two research streams: (a) music preferences as indicators of similarity in value orientations and (b) similarity in value orientations leading to social attraction. Two laboratory experiments and one dyadic field study demonstrated that music can create interpersonal bonds between young people because music preferences can be cues for similar or dissimilar value orientations, with similarity in values then contributing to social attraction. One study tested and ruled out an alternative explanation (via personality similarity), illuminating the differential impact of perceived value similarity versus personality similarity on social attraction. Value similarity is the missing link in explaining the musical bonding phenomenon, which seems to hold for Western and non-Western samples and in experimental and natural settings.

Development of magnetic and elastic anisotropies in slates during progressive deformation

NASA Astrophysics Data System (ADS)

Hrouda, František; Pros, Zdeněk; Wohlgemuth, Jiří

1993-05-01

Magnetic and elastic anisotropies were investigated in rocks of the Nízký Jeseník Mountains (northeast Bohemian Massif) ranging in lithology from almost unmetamorphosed sediments, through slate, to phyllite, and showing a range of structural styles from sedimentary, through spaced and slaty cleavage, to metamorphic schistosity. In unmetamorphosed and undeformed sedimentary rocks, both the anisotropies display close relationships to the sedimentary fabric. During the development of the spaced and slaty cleavage they are gradually re-oriented into the attitudes of the deformational fabrics, and in the rocks with metamorphic schistosity they are fully related to the deformational fabric elements, which can be oriented in a very different way from the original sedimentary structures. The magnetic anisotropy is mostly due to the preferred orientation of phyllosilicates generated during very weak regional metamorphism, and subordinately due to the preferred orientation of magnetite. The elastic anisotropy is probably controlled by the preferred orientation of phyllosilicates and by the existence of oriented systems of microcracks.

Predicted contextual modulation varies with distance from pinwheel centers in the orientation preference map

PubMed Central

Okamoto, Tsuyoshi; Ikezoe, Koji; Tamura, Hiroshi; Watanabe, Masataka; Aihara, Kazuyuki; Fujita, Ichiro

2011-01-01

In the primary visual cortex (V1) of some mammals, columns of neurons with the full range of orientation preferences converge at the center of a pinwheel-like arrangement, the ‘pinwheel center' (PWC). Because a neuron receives abundant inputs from nearby neurons, the neuron's position on the cortical map likely has a significant impact on its responses to the layout of orientations inside and outside its classical receptive field (CRF). To understand the positional specificity of responses, we constructed a computational model based on orientation preference maps in monkey V1 and hypothetical neuronal connections. The model simulations showed that neurons near PWCs displayed weaker but detectable orientation selectivity within their CRFs, and strongly reduced contextual modulation from extra-CRF stimuli, than neurons distant from PWCs. We suggest that neurons near PWCs robustly extract local orientation within their CRF embedded in visual scenes, and that contextual information is processed in regions distant from PWCs. PMID:22355631

Synthesis and characterization of sputtered titanium nitride as a nucleation layer for novel neural electrode coatings

NASA Astrophysics Data System (ADS)

Sait, R. A.; Cross, R. B. M.

2017-12-01

A growing demand for chronically implantable electrodes has led to a search for the most suitable neural electrode interface material. Nobel metals such as platinum (Pt) are inadequate for electrode/neuron interfaces at small scales due to their poor electrochemical properties, low charge injection and high charge density per unit area. Titanium nitride (TiN) has been implemented in neural electrodes application due to its outstanding properties. In this work, TiNx films were deposited by non-reactive radio frequency (RF) magnetron sputtering towards the development of a novel TiN nanowires (NWs) neural interface. Although, there is substantial work on this material, its growth using non-reactive RF magnetron sputtering has not been reported previously and optimised towards the growth of TiN NWs and their use in neural interface applications. The sputtering parameters of RF power and argon (Ar) flow rate were varied in order to investigate their effects on the structural, electrical and electrochemical properties of the TiN films. A dense film morphology was observed in the scanning electron microscopy (SEM) images of TiN thin films showing a columnar structure. The film preferential orientation was changed between (200) and (111) with Ar flow rate due to the variation of the kinetic energy (KE) of the sputtered atoms. The crystallites size obtained were in the range of 13-95 nm. Surface roughness was found to increase from 0.69 to 1.95 nm as Ar flow rate increased. TiNx films showed a good electrical resistivity of 228 μΩ cm. Stoichiometry was found to vary with sputtering conditions in which the nitrogen content was found to deplete from the film at low Ar flow rate. The electrochemical behaviour of TiN films were characterised and the highest capacitance value obtained was 0.416 mF/cm2. From the results, it can be suggested that TiN thin film can be easily optimised to act as a nucleation layer for the growth of nanowires.

Formation of highly preferred orientation of β-Sn grains in solidified Cu/SnAgCu/Cu micro interconnects under temperature gradient effect

NASA Astrophysics Data System (ADS)

Zhao, N.; Zhong, Y.; Dong, W.; Huang, M. L.; Ma, H. T.; Wong, C. P.

2017-02-01

β-Sn grain orientation and configuration are becoming crucial factors to dominate the lifetime of solder interconnects in three-dimensional integrated circuit packaging. In this paper, we found that a temperature gradient during solidification significantly dominated the orientation and configuration of the final β-Sn grains in Cu/SnAgCu/Cu micro interconnects. Being different from the random orientations and growth fronts meeting or cyclic twin boundary forming near the center after homogeneous temperature bonding, the β-Sn grains solidified under a certain temperature gradient were observed to follow a highly preferred orientation with their c-axis departing from the direction of temperature gradient by about 45°-88°. Meanwhile, these preferred oriented β-Sn grains consisted of low angle grain boundary structures with misorientation in the range of 0°-15°. The mechanism was explained in terms of the anisotropy and directional growth of β-Sn grains. The results pave the way for grain orientation control in 3D packaging technology.

Local sensitivity to stimulus orientation and spatial frequency within the receptive fields of neurons in visual area 2 of macaque monkeys

PubMed Central

Tao, X.; Zhang, B.; Smith, E. L.; Nishimoto, S.; Ohzawa, I.

2012-01-01

We used dynamic dense noise stimuli and local spectral reverse correlation methods to reveal the local sensitivities of neurons in visual area 2 (V2) of macaque monkeys to orientation and spatial frequency within their receptive fields. This minimized the potentially confounding assumptions that are inherent in stimulus selections. The majority of neurons exhibited a relatively high degree of homogeneity for the preferred orientations and spatial frequencies in the spatial matrix of facilitatory subfields. However, about 20% of all neurons showed maximum orientation differences between neighboring subfields that were greater than 25 deg. The neurons preferring horizontal or vertical orientations showed less inhomogeneity in space than the neurons preferring oblique orientations. Over 50% of all units also exhibited suppressive profiles, and those were more heterogeneous than facilitatory profiles. The preferred orientation and spatial frequency of suppressive profiles differed substantially from those of facilitatory profiles, and the neurons with suppressive subfields had greater orientation selectivity than those without suppressive subfields. The peak suppression occurred with longer delays than the peak facilitation. These results suggest that the receptive field profiles of the majority of V2 neurons reflect the orderly convergence of V1 inputs over space, but that a subset of V2 neurons exhibit more complex response profiles having both suppressive and facilitatory subfields. These V2 neurons with heterogeneous subfield profiles could play an important role in the initial processing of complex stimulus features. PMID:22114163

Thermoregulatory behavior and orientation preference in bearded dragons.

PubMed

Black, Ian R G; Tattersall, Glenn J

2017-10-01

The regulation of body temperature is a critical function for animals. Although reliant on ambient temperature as a heat source, reptiles, and especially lizards, make use of multiple voluntary and involuntary behaviors to thermoregulate, including postural changes in body orientation, either toward or away from solar sources of heat. This thermal orientation may also result from a thermoregulatory drive to maintain precise control over cranial temperatures or a rostrally-driven sensory bias. The purpose of this work was to examine thermal orientation behavior in adult and neonatal bearded dragons (Pogona vitticeps), to ascertain its prevalence across different life stages within a laboratory situation and its interaction with behavioral thermoregulation. Both adult and neonatal bearded dragons were placed in a thermal gradient and allowed to voluntarily select temperatures for up to 8h to observe the presence and development of a thermoregulatory orientation preference. Both adult and neonatal dragons displayed a non-random orientation, preferring to face toward a heat source while achieving mean thermal preferences of ~ 33-34°C. Specifically, adult dragons were more likely to face a heat source when at cooler ambient temperatures and less likely at warmer temperatures, suggesting that orientation behavior counter-balances local selected temperatures but contributes to their thermoregulatory response. Neonates were also more likely to select cooler temperatures when facing a heat source, but required more experience before this orientation behavior emerged. Combined, these results demonstrate the importance of orientation to behavioral thermoregulation in multiple life stages of bearded dragons. Copyright © 2017 Elsevier Ltd. All rights reserved.

Long adaptation reveals mostly attractive shifts of orientation tuning in cat primary visual cortex.

PubMed

Ghisovan, N; Nemri, A; Shumikhina, S; Molotchnikoff, S

2009-12-15

In the adult brain, sensory cortical neurons undergo transient changes of their response properties following prolonged exposure to an appropriate stimulus (adaptation). In cat V1, orientation-selective cells shift their preferred orientation after being adapted to a non-preferred orientation. There are conflicting reports as to the direction of those shifts, towards (attractive) or away (repulsive) from the adapter. Moreover, the mechanisms underlying attractive shifts remain unexplained. In the present investigation we show that attractive shifts are the most frequent outcome of a 12 min adaptation. Overall, cells displaying selectivity for oblique orientations exhibit significantly larger shifts than cells tuned to cardinal orientations. In addition, cells selective to cardinal orientations had larger shift amplitudes when the absolute difference between the original preferred orientation and the adapting orientation increased. Conversely, cells tuned to oblique orientations exhibited larger shift amplitudes when this absolute orientation difference was narrower. Hence, neurons tuned to oblique contours appear to show more plasticity in response to small perturbations. Two different mechanisms appear to produce attractive and repulsive orientation shifts. Attractive shifts result from concurrent response depression on the non-adapted flank and selective response facilitation on the adapted flank of the orientation tuning curve. In contrast, repulsive shifts are caused solely by response depression on the adapted flank. We suggest that an early mechanism leads to repulsive shifts while attractive shifts engage a subsequent late facilitation. A potential role for attractive shifts may be improved stimulus discrimination around the adapting orientation.

Parents' assessment of circadian preference in elementary school-aged children: Validity and relations to educational outcomes.

PubMed

Scherrer, Vsevolod; Roberts, Richard; Preckel, Franzis

2016-01-01

Meta-analyses suggest that morning-oriented students obtain better school grades than evening-oriented students. This finding has generally been found for students in high school using self-report data for the assessment of circadian preference. Two studies (N = 2718/192) investigated whether these findings generalize across samples (i.e. elementary school-aged students) and methods (i.e. parent reports). These studies also explored whether the relation between circadian preference and school achievement could be explained within an expectancy-value framework. To this end, the Lark-Owl Chronotype Indicator (LOCI) was modified to obtain parents' evaluations of their children's circadian preference, while students completed a battery of assessments designed to explore the test-criterion evidence. Structural equation modeling and correlational analyses revealed: (1) morning and evening orientation were two separable factors of children's circadian preference; (2) correlations with behavioral (e.g. sleep and eating times) and psychological (e.g. cognitive ability) data supported the test-criterion validity of both factors; (3) morning orientation was positively related to school achievement and (4) consistent with an expectancy-value framework this relation was mediated by children's academic self-concept (ASC). These findings have important research and policy implications for considering circadian preference in the schooling of elementary students.

Influence of magnetic field on zebrafish activity and orientation in a plus maze.

PubMed

Osipova, Elena A; Pavlova, Vera V; Nepomnyashchikh, Valentin A; Krylov, Viacheslav V

2016-01-01

We describe an impact of the geomagnetic field (GMF) and its modification on zebrafish's orientation and locomotor activity in a plus maze with four arms oriented to the north, east, south and west. Zebrafish's directional preferences were bimodal in GMF: they visited two arms oriented in opposed directions (east-west) most frequently. This bimodal preference remained stable for same individuals across experiments divided by several days. When the horizontal GMF component was turned 90° clockwise, the preference accordingly shifted by 90° to arms oriented to the north and south. Other modifications of GMF (reversal of both vertical and horizontal GMF components; reversal of vertical component only; and reversal of horizontal component only) did not exert any discernible effect on the orientation of zebrafish. The 90° turn of horizontal component also resulted in a significant increase of fish's locomotor activity in comparison with the natural GMF. This increase became even more pronounced when the horizontal component was repeatedly turned by 90° and back with 1min interval between turns. Our results show that GMF and its variations should be taken into account when interpreting zebrafish's directional preferences and locomotor activity in mazes and other experimental devices. Copyright © 2015. Published by Elsevier B.V.

Catalyst effects in heterogeneous nucleation of acicular ferrite

NASA Astrophysics Data System (ADS)

Grong, Ø.; Kluken, A. O.; Nylund, H. K.; Dons, A. L.; Hjelen, J.

1995-03-01

The present investigation is concerned with basic studies of the mechanisms of acicular ferrite (AF)’formation in low-alloy steel weld metal. It is confirmed experimentally that different types of orientation relationships exist between AF and specific cubic inclusion constituent phases (i.e., γ-Al2 MnOAl2O3, and TiN). Since the majority of these falls within the Bain orientation region, it is concluded that the associated reduction of the energy barrier to nucleation is the primary cause for the ferrite nucleus to develop orientation relationships with both the substrate and the austenite. Theoretical calculations show that about 12 pct of the inclusions will contain a cubic phase that lies within the Bain region purely by chance if they are randomly orientated in space. This intrinsic density of heterogeneous nucleation sites is sufficiently high to promote the formation of fine, interlocking AF laths in the weld metal during the y- to- a transformation.

Preferred orientation of nanoscale order at the surface of amorphous Ge{sub 2}Sb{sub 2}Te{sub 5} films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tony Li, Tian; Abelson, John R.; Coordinated Science Laboratory, University of Illinois at Urbana-Champaign, 1308 W. Main St., Urbana, Illinois 61801

2013-11-11

We report evidence that as-deposited amorphous Ge{sub 2}Sb{sub 2}Te{sub 5} thin films contain nanoscale clusters that exhibit a preferred orientation, attributed to the earliest stages of heterogeneous nucleation. Fluctuation transmission electron microscopy reveals structural order in the samples, but (220)-related contributions are suppressed. When homogeneous nucleation is promoted via electron bombardment, the sample remains diffraction amorphous but the (220) contribution appears. We simulated data for randomly oriented nanoscale order using ab initio molecular-dynamics models of Ge{sub 2}Sb{sub 2}Te{sub 5}. The simulated (220) contribution always has larger magnitude than higher-order signals; thus, the lack of the experimental signal indicates a significantmore » preferred orientation.« less

Critical CuI buffer layer surface density for organic molecular crystal orientation change

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahn, Kwangseok; Kim, Jong Beom; Lee, Dong Ryeol, E-mail: drlee@ssu.ac.kr

We have determined the critical surface density of the CuI buffer layer inserted to change the preferred orientation of copper phthalocyanine (CuPc) crystals grown on the buffer layer. X-ray reflectivity measurements were performed to obtain the density profiles of the buffer layers and out-of-plane and 2D grazing-incidence X-ray diffraction measurements were performed to determine the preferred orientations of the molecular crystals. Remarkably, it was found that the preferred orientation of the CuPc film is completely changed from edge-on (1 0 0) to face-on (1 1 −2) by a CuI buffer layer with a very low surface density, so low thatmore » a large proportion of the substrate surface is bare.« less

Irregular-Mesh Terrain Analysis and Incident Solar Radiation for Continuous Hydrologic Modeling in Mountain Watersheds

NASA Astrophysics Data System (ADS)

Moreno, H. A.; Ogden, F. L.; Alvarez, L. V.

2016-12-01

This research work presents a methodology for estimating terrain slope degree, aspect (slope orientation) and total incoming solar radiation from Triangular Irregular Network (TIN) terrain models. The algorithm accounts for self shading and cast shadows, sky view fractions for diffuse radiation, remote albedo and atmospheric backscattering, by using a vectorial approach within a topocentric coordinate system and establishing geometric relations between groups of TIN elements and the sun position. A normal vector to the surface of each TIN element describes slope and aspect while spherical trigonometry allows computingunit vector defining the position of the sun at each hour and day of the year. Thus, a dot product determines the radiation flux at each TIN element. Cast shadows are computed by scanning the projection of groups of TIN elements in the direction of the closest perpendicular plane to the sun vector only in the visible horizon range. Sky view fractions are computed by a simplified scanning algorithm from the highest to the lowest triangles along prescribed directions and visible distances, useful to determine diffuse radiation. Finally, remotealbedo is computed from the sky view fraction complementary functions for prescribed albedo values of the surrounding terrain only for significant angles above the horizon. The sensitivity of the different radiative components is tested a in a moutainuous watershed in Wyoming, to seasonal changes in weather and surrounding albedo (snow). This methodology represents an improvement on the current algorithms to compute terrain and radiation values on triangular-based models in an accurate and efficient manner. All terrain-related features (e.g. slope, aspect, sky view fraction) can be pre-computed and stored for easy access for a subsequent, progressive-in-time, numerical simulation.

Method and apparatus for dissociating metals from metal compounds extracted into supercritical fluids

DOEpatents

Wai, Chien M.; Hunt, Fred H.; Smart, Neil G.; Lin, Yuehe

2000-01-01

A method for dissociating metal-ligand complexes in a supercritical fluid by treating the metal-ligand complex with heat and/or reducing or oxidizing agents is described. Once the metal-ligand complex is dissociated, the resulting metal and/or metal oxide form fine particles of substantially uniform size. In preferred embodiments, the solvent is supercritical carbon dioxide and the ligand is a .beta.-diketone such as hexafluoroacetylacetone or dibutyldiacetate. In other preferred embodiments, the metals in the metal-ligand complex are copper, silver, gold, tungsten, titanium, tantalum, tin, or mixtures thereof. In preferred embodiments, the reducing agent is hydrogen. The method provides an efficient process for dissociating metal-ligand complexes and produces easily-collected metal particles free from hydrocarbon solvent impurities. The ligand and the supercritical fluid can be regenerated to provide an economic, efficient process.

Behind the mask of method: political orientation and constitutional interpretive preferences.

PubMed

Furgeson, Joshua R; Babcock, Linda; Shane, Peter M

2008-12-01

Debate about how to best interpret the Constitution often revolves around interpretive methodologies (e.g., originalism or expansive interpretation). This article examines whether individuals' political orientation influences the methodologies they prefer to use to interpret the Constitution. We study this proposed relationship using a survey of federal law clerks and an experimental study with college students. The survey results indicate that, compared to conservatives, liberal clerks prefer the current meaning or the most plausible appealing meaning of the constitutional text, while conservatives prefer the original meaning of the text. Liberal clerks also prefer to interpret the Constitution much more expansively. The second study manipulates the policy implications of expansive interpretation and finds this manipulation differentially affects liberals' and conservatives' expansiveness preferences.

Influences of Indium Tin Oxide Layer on the Properties of RF Magnetron-Sputtered (BaSr)TiO3 Thin Films on Indium Tin Oxide-Coated Glass Substrate

NASA Astrophysics Data System (ADS)

Kim, Tae Song; Oh, Myung Hwan; Kim, Chong Hee

1993-06-01

Nearly stoichiometric ((Ba+Sr)/Ti=1.08-1.09) and optically transparent (BaSr)TiO3 thin films were deposited on an indium tin oxide (ITO)-coated glass substrate by means of rf magnetron sputtering for their application to the insulating layer of an electroluminescent flat panel display. The influence of the ITO layer on the properties of (BaSr)TiO3 thin films deposited on the ITO-coated substrate was investigated. The ITO layer did not affect the crystallographic orientation of (BaSr)TiO3 thin film, but enhanced the grain growth. Another effect of the ITO layer on (BaSr)TiO3 thin films was the interdiffusion phenomenon, which was studied by means of secondary ion mass spectrometry (SIMS). As the substrate temperature increased, interdiffusion intensified at the interface not only between the grown film and ITO layer but also between the ITO layer and base glass substrate. The refractive index (nf) of (BaSr)TiO3 thin film deposited on a bare glass substrate was 2.138-2.286, as a function of substrate temperature.

Preference for attractiveness and thinness in a partner: influence of internalization of the thin ideal and shape/weight dissatisfaction in heterosexual women, heterosexual men, lesbians, and gay men.

PubMed

Legenbauer, Tanja; Vocks, Silja; Schäfer, Corinna; Schütt-Strömel, Sabine; Hiller, Wolfgang; Wagner, Christof; Vögele, Claus

2009-06-01

This study assesses whether characteristics of one's own body image influences preferences of attractiveness in a partner. The role of gender and sexual orientation is also considered. Heterosexual women (n=67), lesbian women (n=73), heterosexual men (n=61) and gay men (n=82) participated in an internet survey assessing attitudes towards the body and preferences of attractiveness in a partner. Men in particular were found to prefer attractive partners, regardless of sexual orientation. Weight/shape dissatisfaction was found to be a negative predictor for heterosexual men and women. For gay men, preferences were better explained by internalization and weight/shape dissatisfaction. No such associations were found in the lesbian group. Levels of weight/shape dissatisfaction and internalization of socio-cultural slenderness ideals influence expectations of thinness and attractiveness in a partner with this effect being modified by gender and sexual orientation.

Influence of N2 partial pressure on structural and microhardness properties of TiN/ZrN multilayers deposited by Ar/N2 vacuum arc discharge

NASA Astrophysics Data System (ADS)

Naddaf, M.; Abdallah, B.; Ahmad, M.; A-Kharroub, M.

2016-08-01

The influence of N2 partial pressure on structural, mechanical and wetting properties of multilayered TiN/ZrN thin films deposited on silicon substrates by vacuum arc discharge of (N2 + Ar) gas mixtures is investigated. X-ray diffraction (XRD) results show that the average texturing coefficient of (1 1 1) orientation and the grain size of both TiN and ZrN individual layers increase with increasing the N2 partial pressure. The Rutherford back scattering (RBS) measurements and analysis reveal that incorporation of the nitrogen in the film increases with increasing the N2 partial pressure and both TiN and ZrN individual layers have a nitrogen over-stoichiometry for N2 partial pressure ⩾50%. The change in the film micro-hardness is correlated to the changes in crystallographic texture, grain size, stoichiometry and the residual stress in the film as a function of the N2 partial pressure. In particular, stoichiometry of ZrN and TiN individual is found to play the vital role in determining the multilayer hardness. The multilayer film deposited at N2 partial pressure of 25% has the best stoichiometric ratio of both TiN and ZrN layers and the highest micro-hardness of about 32 GPa. In addition, water contact angle (WCA) measurements and analysis show a decrease in the work of adhesion on increasing the N2 partial pressure.

Recrystallized arrays of bismuth nanowires with trigonal orientation.

PubMed

Limmer, Steven J; Yelton, W Graham; Erickson, Kristopher J; Medlin, Douglas L; Siegal, Michael P

2014-01-01

We demonstrate methods to improve the crystalline-quality of free-standing Bi nanowires arrays on a Si substrate and enhance the preferred trigonal orientation for thermoelectric performance by annealing the arrays above the 271.4 °C Bi melting point. The nanowires maintain their geometry during melting due to the formation of a thin Bi-oxide protective shell that contains the molten Bi. Recrystallizing nanowires from the melt improves crystallinity; those cooled rapidly demonstrate a strong trigonal orientation preference.

Preference for human body odors is influenced by gender and sexual orientation.

PubMed

Martins, Yolanda; Preti, George; Crabtree, Christina R; Runyan, Tamar; Vainius, Aldona A; Wysocki, Charles J

2005-09-01

Human body odor may contribute to selection of partners. If so, sexual orientation may influence preference for and perhaps production of human body odors. In a test of these hypotheses, heterosexual and homosexual males and females made two-alternative forced-choice preference judgments for body odors obtained from other heterosexual and homosexual males and females. Subjects chose between odors from (a) heterosexual males and gay males, (b) heterosexual males and heterosexual females, (c) heterosexual females and lesbians, and (d) gay males and lesbians. Results indicate that differences in body odor are detected and responded to on the basis of, in part, an individual's gender and sexual orientation. Possible mechanisms underlying these findings are discussed.

Metal/metal oxide doped oxide catalysts having high deNOx selectivity for lean NOx exhaust aftertreatment systems

DOEpatents

Park, Paul W.

2004-03-16

A lean NOx catalyst and method of preparing the same is disclosed. The lean NOx catalyst includes a ceramic substrate, an oxide support material, preferably .gamma.-alumina, deposited on the substrate and a metal promoter or dopant introduced into the oxide support material. The metal promoters or dopants are selected from the group consisting of indium, gallium, tin, silver, germanium, gold, nickel, cobalt, copper, iron, manganese, molybdenum, chromium, cerium, vanadium, oxides thereof, and combinations thereof. The .gamma.-alumina preferably has a pore volume of from about 0.5 to about 2.0 cc/g; a surface area of between about 80 to 350 m.sup.2 /g; an average pore size diameter of between about 3 to 30 nm; and an impurity level of less than or equal to 0.2 weight percent. In a preferred embodiment the .gamma.-alumina is prepared by a sol-gel method, with the metal doping of the .gamma.-alumina preferably accomplished using an incipient wetness impregnation technique.

Social Dominance Orientation, Right-Wing Authoritarianism, Sexism, and Prejudice toward Women in the Workforce

ERIC Educational Resources Information Center

Christopher, Andrew N.; Wojda, Mark R.

2008-01-01

This study examined how social dominance orientation (SDO) and right-wing authoritarianism (RWA) were related to two different forms of prejudice against working women: employment skepticism and traditional role preference. Three hundred forty-nine American adults completed measures of SDO, RWA, employment skepticism, traditional role preference,…

Orienting the Microstructure Evolution of Copper Phthalocyanine as an Anode Interlayer in Inverted Polymer Solar Cells for High Performance.

PubMed

Li, Zhiqi; Liu, Chunyu; Zhang, Xinyuan; Li, Shujun; Zhang, Xulin; Guo, Jiaxin; Guo, Wenbin; Zhang, Liu; Ruan, Shengping

2017-09-20

Recent advances in the interfacial modification of inverted-type polymer solar cells (PSCs) have resulted from controlling the surface energy of the cathode-modified layer (TiO 2 or ZnO) to enhance the short-circuit current (J sc ) or optimizing the contact morphology of the cathode (indium tin oxide or fluorine-doped tin oxide) and active layer to increase the fill factor. Herein, we report that the performance enhancement of PSCs is achieved by incorporating a donor macromolecule copper phthalocyanine (CuPc) as an anode modification layer. Using the approach based on orienting the microstructure evolution, uniformly dispersed island-shaped CuPc spot accumulations are built on the top of PTB7:PC 71 BM blend film, leading to an efficient spectral absorption and photogenerated exciton splitting. The best power conversion efficiency of PSCs is increased up to 9.726%. In addition to the enhanced light absorption, the tailored anode energy level alignment and optimized boundary morphology by incorporating the CuPc interlayer boost charge extraction efficiency and suppress the interfacial molecular recombination. These results demonstrate that surface morphology induction through molecular deposition is an effective method to improve the performance of PSCs, which reveals the potential implications of the interlayer between the organic active layer and the electrode buffer layer.

Spontaneous expression of magnetic compass orientation in an epigeic rodent: the bank vole, Clethrionomys glareolus

NASA Astrophysics Data System (ADS)

Oliveriusová, Ludmila; Němec, Pavel; Pavelková, Zuzana; Sedláček, František

2014-07-01

Magnetoreception has been convincingly demonstrated in only a few mammalian species. Among rodents, magnetic compass orientation has been documented in four species of subterranean mole rats and two epigeic (i.e. active above ground) species—the Siberian hamster and the C57BL/6J mouse. The mole rats use the magnetic field azimuth to determine compass heading; their directional preference is spontaneous and unimodal, and their magnetic compass is magnetite-mediated. By contrast, the primary component of orientation response is learned in the hamster and the mouse, but both species also exhibit a weak spontaneous bimodal preference in the natural magnetic field. To determine whether the magnetic compass of wild epigeic rodents features the same functional properties as that of laboratory rodents, we investigated magnetic compass orientation in the bank vole Clethrionomys glareolus (Cricetidae, Rodentia). The voles exhibited a robust spontaneous bimodal directional preference, i.e. built nests and slept preferentially along the north-south axis, and deflected their directional preference according to a shift in the direction of magnetic north, clearly indicating that they were deriving directional information from the magnetic field. Thus, bimodal, axially symmetrical directional choice seems to be a common feature shared by epigeic rodents. However, spontaneous directional preference in the bank vole appeared to be more pronounced than that reported in the hamster and the mouse. These findings suggest that bank voles are well suited for future studies investigating the adaptive significance and mechanisms of magnetic orientation in epigeic rodents.

Spontaneous expression of magnetic compass orientation in an epigeic rodent: the bank vole, Clethrionomys glareolus.

PubMed

Oliveriusová, Ludmila; Němec, Pavel; Pavelková, Zuzana; Sedláček, František

2014-07-01

Magnetoreception has been convincingly demonstrated in only a few mammalian species. Among rodents, magnetic compass orientation has been documented in four species of subterranean mole rats and two epigeic (i.e. active above ground) species-the Siberian hamster and the C57BL/6J mouse. The mole rats use the magnetic field azimuth to determine compass heading; their directional preference is spontaneous and unimodal, and their magnetic compass is magnetite-mediated. By contrast, the primary component of orientation response is learned in the hamster and the mouse, but both species also exhibit a weak spontaneous bimodal preference in the natural magnetic field. To determine whether the magnetic compass of wild epigeic rodents features the same functional properties as that of laboratory rodents, we investigated magnetic compass orientation in the bank vole Clethrionomys glareolus (Cricetidae, Rodentia). The voles exhibited a robust spontaneous bimodal directional preference, i.e. built nests and slept preferentially along the north-south axis, and deflected their directional preference according to a shift in the direction of magnetic north, clearly indicating that they were deriving directional information from the magnetic field. Thus, bimodal, axially symmetrical directional choice seems to be a common feature shared by epigeic rodents. However, spontaneous directional preference in the bank vole appeared to be more pronounced than that reported in the hamster and the mouse. These findings suggest that bank voles are well suited for future studies investigating the adaptive significance and mechanisms of magnetic orientation in epigeic rodents.

Zebrafish respond to the geomagnetic field by bimodal and group-dependent orientation.

PubMed

Takebe, Akira; Furutani, Toshiki; Wada, Tatsunori; Koinuma, Masami; Kubo, Yoko; Okano, Keiko; Okano, Toshiyuki

2012-01-01

A variety of animals use Earth's magnetic field as a reference for their orientation behaviour. Although distinctive magnetoreception mechanisms have been postulated for many migrating or homing animals, the molecular mechanisms are still undefined. In this study, we found that zebrafish, a model organism suitable for genetic manipulation, responded to a magnetic field as weak as the geomagnetic field. Without any training, zebrafish were individually released into a circular arena that was placed in an artificial geomagnetic field, and their preferred magnetic directions were recorded. Individuals from five out of the seven zebrafish groups studied, groups mostly comprised of the offspring of predetermined pairs, showed bidirectional orientation with group-specific preferences regardless of close kinships. The preferred directions did not seem to depend on gender, age or surrounding environmental factors, implying that directional preference was genetically defined. The present findings may facilitate future study on the molecular mechanisms underlying magnetoreception.

Preparation and characterization of Cu2SnS3 thin films by electrodeposition

NASA Astrophysics Data System (ADS)

Patel, Biren; Narasimman, R.; Pati, Ranjan K.; Mukhopadhyay, Indrajit; Ray, Abhijit

2018-05-01

Cu2SnS3 thin films were electrodeposited on F:SnO2/Glass substrates at room temperature by using aqueous solution. Copper and tin were first electrodeposited from single bath and post annealed in the presence of sulphur atmosphere to obtain the Cu2SnS3 phase. The Cu2SnS3 phase with preferred orientation along the (112) crystal direction grows to greater extent by the post annealing of the film. Raman analysis confirms the monoclinic crystal structure of Cu2SnS3 with principle mode of vibration as A1 (symmetric breathing mode) corresponding to the band at 291 cm-1. It also reveals the benign coexistence of orthorhombic Cu3SnS4 and Cu2SnS7 phases. Optical properties of the film show direct band gap of 1.25 eV with a high absorption coefficient of the order of 104 cm-1 in the visible region. Photo activity of the electrodeposited film was established in two electrode photoelectro-chemical cell, where an open circuit voltage of 91.6 mV and a short circuit current density of 10.6 µA/cm2 were recorded. Fabrication of Cu2SnS3 thin film heterojunction solar cell is underway.

Retinal constraints on orientation specificity in cat visual cortex.

PubMed

Schall, J D; Vitek, D J; Leventhal, A G

1986-03-01

Most retinal ganglion cells (Levick and Thibos, 1982) and cortical cells (Leventhal, 1983; Leventhal et al., 1984) subserving peripheral vision respond best to stimuli that are oriented radially, i.e., like the spokes of a wheel with the area centralis at the hub. We have extended this work by comparing directly the distributions of orientations represented in topographically corresponding regions of retina and visual cortex. Both central and peripheral regions were studied. The relations between the orientations of neighboring ganglion cells and the manner in which the overrepresentation of radial orientations is accommodated in the functional architecture of visual cortex were also studied. Our results are based on an analysis of the orientations of the dendritic fields of 1296 ganglion cells throughout the retina and the preferred orientations of 1389 cells located in retinotopically corresponding regions of cortical areas 17, 18, and 19 in the cat. We find that horizontal and vertical orientations are overrepresented in regions of both retina and visual cortex subserving the central 5 degrees of vision. The distributions of the orientations of retinal ganglion cells and cortical cells subserving the horizontal, vertical, and diagonal meridians outside the area centralis differ significantly. The distribution of the preferred orientations of the S (simple) cells in areas 17, 18 and 19 subserving a given part of the retina corresponds to the distribution of the dendritic field orientations of the ganglion cells in that part of retina. The distribution of the preferred orientations of C (complex) cells with narrow receptive fields in area 17 but not C cells with wide receptive fields in areas 17, 18, or 19 subserving a given part of the retina matches the distribution of the orientations of the ganglion cells in that part of retina. The orientations of all of the alpha-cells in 5-9 mm2 patches of retina along the horizontal, vertical, and oblique meridians were determined. A comparison of the orientations of neighboring cells indicates that other than a mutual tendency to be oriented radially, ganglion cells with similar orientations are not clustered in the retina. Reconstructions of electrode penetrations into regions of visual cortex representing peripheral retina indicate that columns subserving radial orientations are wider than those subserving nonradial orientations. Our results provide evidence that the distribution of the preferred orientations of simple cells in visual cortex subserving any region of the visual field matches the distribution of the orientations of the ganglion cells subserving the same region of the visual field.(ABSTRACT TRUNCATED AT 400 WORDS)

Gender identity rather than sexual orientation impacts on facial preferences.

PubMed

Ciocca, Giacomo; Limoncin, Erika; Cellerino, Alessandro; Fisher, Alessandra D; Gravina, Giovanni Luca; Carosa, Eleonora; Mollaioli, Daniele; Valenzano, Dario R; Mennucci, Andrea; Bandini, Elisa; Di Stasi, Savino M; Maggi, Mario; Lenzi, Andrea; Jannini, Emmanuele A

2014-10-01

Differences in facial preferences between heterosexual men and women are well documented. It is still a matter of debate, however, how variations in sexual identity/sexual orientation may modify the facial preferences. This study aims to investigate the facial preferences of male-to-female (MtF) individuals with gender dysphoria (GD) and the influence of short-term/long-term relationships on facial preference, in comparison with healthy subjects. Eighteen untreated MtF subjects, 30 heterosexual males, 64 heterosexual females, and 42 homosexual males from university students/staff, at gay events, and in Gender Clinics were shown a composite male or female face. The sexual dimorphism of these pictures was stressed or reduced in a continuous fashion through an open-source morphing program with a sequence of 21 pictures of the same face warped from a feminized to a masculinized shape. An open-source morphing program (gtkmorph) based on the X-Morph algorithm. MtF GD subjects and heterosexual females showed the same pattern of preferences: a clear preference for less dimorphic (more feminized) faces for both short- and long-term relationships. Conversely, both heterosexual and homosexual men selected significantly much more dimorphic faces, showing a preference for hyperfeminized and hypermasculinized faces, respectively. These data show that the facial preferences of MtF GD individuals mirror those of the sex congruent with their gender identity. Conversely, heterosexual males trace the facial preferences of homosexual men, indicating that changes in sexual orientation do not substantially affect preference for the most attractive faces. © 2014 International Society for Sexual Medicine.

Room temperature deposition of sputtered TiN films for superconducting coplanar waveguide resonators

NASA Astrophysics Data System (ADS)

Ohya, S.; Chiaro, B.; Megrant, A.; Neill, C.; Barends, R.; Chen, Y.; Kelly, J.; Low, D.; Mutus, J.; O'Malley, P. J. J.; Roushan, P.; Sank, D.; Vainsencher, A.; Wenner, J.; White, T. C.; Yin, Y.; Schultz, B. D.; Palmstrøm, C. J.; Mazin, B. A.; Cleland, A. N.; Martinis, John M.

2014-01-01

We present a systematic study of the properties of room temperature deposited TiN films by varying the deposition conditions in an ultra-high-vacuum reactive magnetron sputtering chamber. By increasing the deposition pressure from 2 to 9 mTorr while keeping a nearly stoichiometric composition of Ti1-xNx (x = 0.5) without substrate heating, the film resistivity increases, the dominant crystal orientation changes from (100) to (111), grain boundaries become clearer, and the strong compressive in-plane strain changes to weak tensile in-plane strain. The TiN films absorb a high concentration of contaminants including hydrogen, carbon, and oxygen when they are exposed to air after deposition. With the target-substrate distance set to 88 mm the contaminant levels increase from ˜0.1% to ˜10% as the pressure is increased from 2 to 9 mTorr. The contaminant concentrations also correlate with in-plane distance from the center of the substrate and increase by roughly two orders of magnitude as the target-substrate distance is increased from 88 to 266 mm. These contaminants are found to strongly influence the properties of TiN thin films. For instance, the resistivity of stoichiometric films increases by around a factor of 5 as the oxygen content increases from 0.1% to 11%. These results strongly suggest that the energy of the sputtered TiN particles plays a crucial role in determining the TiN film properties, and that it is important to precisely control the energy of these particles to obtain high-quality TiN films. Superconducting coplanar waveguide resonators made from a series of nearly stoichiometric films grown at pressures from 2 to 7 mTorr show a substantial increase in intrinsic quality factor from ˜104 to ˜106 as the magnitude of the compressive strain decreases from nearly 3800 MPa to approximately 150 MPa and the oxygen content increases from 0.1% to 8%. Surprisingly, the films with a higher oxygen content exhibit lower loss, but care must be taken when depositing at room temperature to avoid nonuniform oxygen incorporation, which presents as a radially dependent resistivity and becomes a radially dependent surface inductance in the superconductor.

Collectivists' contingency and autonomy as predictors of buffet preferences among Taiwanese adolescents.

PubMed

Chiou, Wen-Bin

2006-01-01

In a culture or society with high collectivism, contingent orientation and constrained autonomy are the prominent characteristics of adolescents' self-construal. This article examined whether Taiwanese adolescents' contingency and autonomy were associated with their prevalent preferences for buffet consumption. Findings in a panel survey indicated that contingency was positively correlated with adolescents' buffet preference, whereas autonomy was negatively correlated. Moreover, the results showed that adolescents' contingent orientation and perceived autonomy could predict their subsequent buffet preference over a half-year period. A laboratory experiment showed that adolescents who perceived lower autonomy exhibited greater preferences for buffet over the other diet consumption. In general, the results suggest that collectivist adolescents' contingency and autonomy were related to their trait-like preferences for buffet, and the state-like preferences for buffet were affected by their perceived levels of autonomy. Findings provide further insights into the impact of adolescents' self-construal on their diet consumption.

Prenatal programming of sexual partner preference: the ram model.

PubMed

Roselli, C E; Stormshak, F

2009-03-01

In our laboratory, the domestic ram is used as an experimental model to study the early programming of neural mechanisms underlying same-sex partner preference. This interest developed from the observation that approximately 8% of domestic rams are sexually attracted to other rams (male-oriented) in contrast to the majority of rams that are attracted to oestrous ewes (female-oriented). One prominent feature of sexual differentiation in many species is the presence of a sexually dimorphic nucleus (SDN) in the preoptic/anterior hypothalamus that is larger in males than in females. Lesion studies in rats and ferrets implicate the SDN in the expression of sexual preferences. We discovered an ovine SDN (oSDN) in the preoptic/anterior hypothalamus that is smaller in male- than in female-oriented rams and similar in size to the oSDN of ewes. Neurones of the oSDN show abundant aromatase expression that is also reduced in male-oriented compared to female-oriented rams. This observation suggests that sexual partner preferences are neurologically hard-wired and could be influenced by hormones. Aromatase-containing neurones constitute a nascent oSDN as early as day 60 of gestation, which becomes sexually dimorphic by day 135 of gestation when it is two-fold larger in males than in females. Exposure of fetal female lambs to exogenous testosterone from days 30-90 of gestation resulted in a masculinised oSDN. These data demonstrate that the oSDN develops prenatally and may influence adult sexual preferences. Surprisingly, inhibition of aromatase activity in the brain of ram foetuses during the critical period did not interfere with defeminisation of adult sexual partner preference or oSDN volume. These results fail to support an essential role for neural aromatase in the sexual differentiation of sheep brain and behaviour. Thus, we propose that oSDN morphology and male-typical partner preferences may instead be programmed through an androgen receptor mechanism not involving aromatisation.

Sex-oriented stable matchings of the marriage problem with correlated and incomplete information

NASA Astrophysics Data System (ADS)

Caldarelli, Guido; Capocci, Andrea; Laureti, Paolo

2001-10-01

In the stable marriage problem two sets of agents must be paired according to mutual preferences, which may happen to conflict. We present two generalizations of its sex-oriented version, aiming to take into account correlations between the preferences of agents and costly information. Their effects are investigated both numerically and analytically.

Formation and characterization of preferred oriented perovskite thin films on single-crystalline substrates

NASA Astrophysics Data System (ADS)

Chen, Lung-Chien; Chen, Cheng-Chiang; Hsiung Chang, Sheng; Lee, Kuan-Lin; Tseng, Zong-Liang; Chen, Sheng-Hui; Kuo, Hao-Chung

2018-06-01

Three single-crystalline (Al2O3, GaN/Al2O3 and InAs) substrates are used to assist the formation of crystallographically preferred oriented CH3NH3PbI3 (MAPbI3) thin films. The estimation of the lattice mismatch at the MAPbI3/substrate interface and water-droplet contact angle experiments indicate that the formation of a preferred oriented MAPbI3 thin film is induced by the single-crystalline substrate and is insensitive to the surface wettibility of the substrate. Moreover, the experimental results suggest that the lattice mismatch at the MAPbI3/single-crystalline semiconductor interface can strongly influence the photovoltaic performance of tandem solar cells.

Effect of thickness on optoelectrical properties of Nb-doped indium tin oxide thin films deposited by RF magnetron sputtering

NASA Astrophysics Data System (ADS)

Li, Shi-na; Ma, Rui-xin; Ma, Chun-hong; Li, Dong-ran; Xiao, Yu-qin; He, Liang-wei; Zhu, Hong-min

2013-05-01

Niobium-doped indium tin oxide (ITO:Nb) thin films are prepared on glass substrates with various film thicknesses by radio frequency (RF) magnetron sputtering from one piece of ceramic target material. The effects of thickness (60-360 nm) on the structural, electrical and optical properties of ITO: Nb films are investigated by means of X-ray diffraction (XRD), ultraviolet (UV)-visible spectroscopy, and electrical measurements. XRD patterns show the highly oriented (400) direction. The lowest resistivity of the films without any heat treatment is 3.1×10-4Ω·cm-1, and the resistivity decreases with the increase of substrate temperature. The highest Hall mobility and carrier concentration are 17.6 N·S and 1.36×1021 cm-3, respectively. Band gap energy of the films depends on substrate temperature, which varies from 3.48 eV to 3.62 eV.

Preparation and characterization of oriented silica nanowires

NASA Astrophysics Data System (ADS)

Sun, S. H.; Meng, G. W.; Zhang, M. G.; Tian, Y. T.; Xie, T.; Zhang, L. D.

2003-11-01

Large-scale of oriented closely packed silica nanowire bunches have been synthesized by using large size (1-10 μm in diameter), low melting point tin droplets as catalyst on silicon wafers at 980 °C. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses show that the amorphous silica nanowires have lengths of 50-100 μm and diameters of 100-200 nm. Unlike any previous observed results using high melting point metal (such as gold and iron) as catalyst, the Sn catalyst growth exhibits many interesting phenomena. Each Sn ball can simultaneously catalyze the growth of many silica nanowires, which is quite different from the conventional vapor-liquid-solid process.

Human Infants' Preference for Left-to-Right Oriented Increasing Numerical Sequences

PubMed Central

de Hevia, Maria Dolores; Girelli, Luisa; Addabbo, Margaret; Macchi Cassia, Viola

2014-01-01

While associations between number and space, in the form of a spatially oriented numerical representation, have been extensively reported in human adults, the origins of this phenomenon are still poorly understood. The commonly accepted view is that this number-space association is a product of human invention, with accounts proposing that culture, symbolic knowledge, and mathematics education are at the roots of this phenomenon. Here we show that preverbal infants aged 7 months, who lack symbolic knowledge and mathematics education, show a preference for increasing magnitude displayed in a left-to-right spatial orientation. Infants habituated to left-to-right oriented increasing or decreasing numerical sequences showed an overall higher looking time to new left-to-right oriented increasing numerical sequences at test (Experiment 1). This pattern did not hold when infants were presented with the same ordinal numerical information displayed from right to left (Experiment 2). The different pattern of results was congruent with the presence of a malleable, context-dependent baseline preference for increasing, left-to-right oriented, numerosities (Experiment 3). These findings are suggestive of an early predisposition in humans to link numerical order with a left-to-right spatial orientation, which precedes the acquisition of symbolic abilities, mathematics education, and the acquisition of reading and writing skills. PMID:24802083

Aragonite pseudomorphs in high-pressure marbles of Syros, Greece

NASA Astrophysics Data System (ADS)

Brady, John B.; Markley, Michelle J.; Schumacher, John C.; Cheney, John T.; Bianciardi, Grace A.

2004-01-01

Numerous rod-shaped calcite crystals occur in the blueschist to eclogite facies marbles of Syros, Greece. The rods show a shape-preferred orientation, and the long axes of the rods are oriented at a large angle to foliation. The crystals also have a crystallographic-preferred orientation: calcite c-axes are oriented parallel to the long axes of the rods. Based on their chemical composition, shape, and occurrence in high-pressure marbles, these calcite crystals are interpreted as topotactic pseudomorphs after aragonite that developed a crystallographic-preferred orientation during peak metamorphism. This interpretation is consistent with deformation of aragonite by dislocation creep, which has been observed in laboratory experiments but has not been previously reported on the basis of field evidence. Subsequent to the high-pressure deformation of the aragonite marbles, the aragonite recrystallized statically into coarse rod-shaped crystals, maintaining the crystallographic orientation developed during deformation. During later exhumation, aragonite reverted to calcite, and the marbles experienced little further deformation, at least in the pseudomorph-rich layers. Some shearing of pseudomorph-bearing marble layers did occur and is indicated by twinning of calcite and by a variable inclination of the pseudomorphs relative to foliation.

Multiscale vector fields for image pattern recognition

NASA Technical Reports Server (NTRS)

Low, Kah-Chan; Coggins, James M.

1990-01-01

A uniform processing framework for low-level vision computing in which a bank of spatial filters maps the image intensity structure at each pixel into an abstract feature space is proposed. Some properties of the filters and the feature space are described. Local orientation is measured by a vector sum in the feature space as follows: each filter's preferred orientation along with the strength of the filter's output determine the orientation and the length of a vector in the feature space; the vectors for all filters are summed to yield a resultant vector for a particular pixel and scale. The orientation of the resultant vector indicates the local orientation, and the magnitude of the vector indicates the strength of the local orientation preference. Limitations of the vector sum method are discussed. Investigations show that the processing framework provides a useful, redundant representation of image structure across orientation and scale.

Innovative Surfaces for Controlled Flow of Liquid Metal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fortini, Arthur J.

2016-03-22

The potential economic, environmental, and strategic benefits associated with the development of fusion energy are numerous. However, application of fusion technology cannot be realized until advanced materials are developed that allow operation under the high heat flux conditions necessary for cost-competitive electric energy generation. Bathing the wall of a fusion reactor plasma-facing component in a liquid metal such as lithium, gallium, or tin is a viable approach for accommodating continuous heat flux levels exceeding 10 MW/m2, and it is also the preferred approach for removing hydrogen isotopes. Stabilizing the liquid film is the key challenge, which can be addressed throughmore » the use of a microtextured surface. In previous work, Ultramet developed high temperature microtextured tungsten and rhenium coatings consisting of thousands of high aspect ratio pyramids per square millimeter that are compatible with lithium, gallium, and tin, and whose effectiveness in wicking molten lithium has been demonstrated even in the presence of strong body forces. Heat transfer and fluid flow characteristics were also modeled. Because of the safety issues surrounding lithium, the current project focused on adapting and optimizing this wicking technology for use with gallium and tin. The coatings were deposited by chemical vapor deposition (CVD), and the height, population density, and morphology of the pyramids was varied to optimize the wetting properties, which were measured and quantified by exposing the coatings to molten gallium or tin. Micron-thick films of other materials were also applied to the textured surfaces to vary the wetting characteristics. Wicking tests were performed with both gallium and tin on a variety of coatings with different textures and surface chemistries, and both metals showed excellent wicking and wettability on virtually all of the textured coatings. Extensive modeling of the interaction between the dendrites and the liquid metal, as well as additional wetting testing, was performed by Digital Materials Solutions (DMS, Carlsbad, CA).« less

Using galvanostatic electroforming of Bi 1–xSb x nanowires to control composition, crystallinity, and orientation

DOE PAGES

Limmer, Steven J.; Medlin, Douglas L.; Siegal, Michael P.; ...

2014-12-03

When using galvanostatic pulse deposition, we studied the factors influencing the quality of electroformed Bi 1–xSb x nanowires with respect to composition, crystallinity, and preferred orientation for high thermoelectric performance. Two nonaqueous baths with different Sb salts were investigated. The Sb salts used played a major role in both crystalline quality and preferred orientations. Nanowire arrays electroformed using an SbI 3 -based chemistry were polycrystalline with no preferred orientation, whereas arrays electroformed from an SbCl 3-based chemistry were strongly crystallographically textured with the desired trigonal orientation for optimal thermoelectric performance. From the SbCl 3 bath, the electroformed nanowire arraysmore » were optimized to have nanocompositional uniformity, with a nearly constant composition along the nanowire length. Moreover, nanowires harvested from the center of the array had an average composition of Bi 0.75 Sb 0.25. However, the nanowire compositions were slightly enriched in Sb in a small region near the edges of the array, with the composition approaching Bi 0.70Sb 0.30.« less

Sexual behaviour of rams: male orientation and its endocrine correlates.

PubMed

Resko, J A; Perkins, A; Roselli, C E; Stellflug, J N; Stormshak, F K

1999-01-01

The components of heterosexual behaviour in rams are reviewed as a basis for understanding partner preference behaviour. A small percentage of rams will not mate with oestrous females and if given a choice will display courtship behaviour towards another ram in preference to a female. Some of the endocrine profiles of these male-oriented rams differ from those of heterosexual controls. These differences include reduced serum concentrations of testosterone, oestradiol and oestrone, reduced capacity to produce testosterone in vitro, and reduced capacity to aromatize androgens in the preoptic-anterior hypothalamus of the brain. Our observation that aromatase activity is significantly lower in the preoptic-anterior hypothalamic area of male-oriented rams than in female-oriented rams may indicate an important neurochemical link to sexual behaviour that should be investigated. The defect in steroid hormone production by the adult testes of the male-oriented ram may represent a defect that can be traced to the fetal testes. If this contention is correct, partner preference behaviour of rams may also be traceable to fetal development and represent a phenomenon of sexual differentiation.

Orienting Periodic Organic-Inorganic Nanoscale Domains Through One-Step Electrodeposition

PubMed Central

Herman, David J.; Goldberger, Joshua E.; Chao, Stephen; Martin, Daniel T.; Stupp, Samuel I

2011-01-01

One of the challenges in the synthesis of hybrid materials with nanoscale structure is to precisely control morphology across length scales. Using a one-step electrodeposition process on indium tin oxide (ITO) substrates followed by annealing, we report here the preparation of materials with preferentially oriented lamellar domains of electron donor surfactants and the semiconductor ZnO. We found that either increasing the concentration of surfactant or the water to dimethyl sulfoxide ratio of solutions used resulted in the suppression of bloom-like morphologies and enhanced the density of periodic domains on ITO substrates. Furthermore, by modifying the surface of the ITO substrate with the conductive polymer blend poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate), we were able to alter the orientation of these electrodeposited lamellar domains to be perpendicular to the substrate. The long-range orientation achieved was characterized by 2D grazing incidence small angle X-ray scattering. This high degree of orientation in electronically active hybrids with alternating nanoscale p-type and n-type domains is of potential interest in photovoltaics or thermoelectric materials. PMID:21142087

ION PUMP

DOEpatents

Milleron, N.

1961-01-01

An ion pump and pumping method are given for low vacuum pressures in which gases introduced into a pumping cavity are ionized and thereafter directed and accelerated into a quantity of liquid gettering metal where they are absorbed. In the preferred embodiment the metal is disposed as a liquid pool upon one electrode of a Phillips ion gauge type pump. Means are provided for continuously and remotely withdrawing and degassing the gettering metal. The liquid gettering metal may be heated if desired, although various combinations of gallium, indium, tin, bismuth, and lead, the preferred metals, have very low melting points. A background pressure of evaporated gettering metal may be provided by means of a resistance heated refractory metal wick protruding from the surface of the pcol of gettering metal.

Self-assembly of tin wires via phase transformation of heteroepitaxial germanium-tin on germanium substrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Wei; Li, Lingzi; Yeo, Yee-Chia, E-mail: yeo@ieee.org

This work demonstrates and describes for the first time an unusual strain-relaxation mechanism by the formation and self-assembly of well-ordered tin wires during the thermal annealing of epitaxial Ge{sub 0.83}Sn{sub 0.17}-on-Ge(001) substrate. Fully strained germanium-tin alloys (Ge{sub 0.83}Sn{sub 0.17}) were epitaxially grown on Ge(001) substrate by molecular beam epitaxy. The morphological and compositional evolution of Ge{sub 0.83}Sn{sub 0.17} during thermal annealing is studied by atomic force microscopy, X-ray diffraction, transmission electron microscopy. Under certain annealing conditions, the Ge{sub 0.83}Sn{sub 0.17} layer decomposes into two stable phases, and well-defined Sn wires that are preferentially oriented along two orthogonal 〈100〉 azimuths aremore » formed. The formation of the Sn wires is related to the annealing temperature and the Ge{sub 0.83}Sn{sub 0.17} thickness, and can be explained by the nucleation of a grain with Sn islands on the outer front, followed by grain boundary migration. The Sn wire formation process is found to be thermally activated, and an activation enthalpy (E{sub c}) of 0.41 eV is extracted. This thermally activated phase transformation, i.e., 2D epitaxial layer to 3D wires, occurs via a mechanism akin to “cellular precipitation.” This synthesis route of Sn wires opens new possibilities for creation of nanoscale patterns at high-throughput without the need for lithography.« less

Can Infants' Orientation to Social Stimuli Predict Later Joint Attention Skills?

ERIC Educational Resources Information Center

Schietecatte, Inge; Roeyers, Herbert; Warreyn, Petra

2012-01-01

From the moment infants are born, they seem to prefer orienting to social stimuli, over objects and non-social stimuli. This preference lasts throughout adulthood and is believed to play a crucial role in social-communicative development. By following up a group of infants at the age of 6, 8, and 12 months, this study explored the role of social…

A spherical model for orientation and spatial-frequency tuning in a cortical hypercolumn.

PubMed Central

Bressloff, Paul C; Cowan, Jack D

2003-01-01

A theory is presented of the way in which the hypercolumns in primary visual cortex (V1) are organized to detect important features of visual images, namely local orientation and spatial-frequency. Given the existence in V1 of dual maps for these features, both organized around orientation pinwheels, we constructed a model of a hypercolumn in which orientation and spatial-frequency preferences are represented by the two angular coordinates of a sphere. The two poles of this sphere are taken to correspond, respectively, to high and low spatial-frequency preferences. In Part I of the paper, we use mean-field methods to derive exact solutions for localized activity states on the sphere. We show how cortical amplification through recurrent interactions generates a sharply tuned, contrast-invariant population response to both local orientation and local spatial frequency, even in the case of a weakly biased input from the lateral geniculate nucleus (LGN). A major prediction of our model is that this response is non-separable with respect to the local orientation and spatial frequency of a stimulus. That is, orientation tuning is weaker around the pinwheels, and there is a shift in spatial-frequency tuning towards that of the closest pinwheel at non-optimal orientations. In Part II of the paper, we demonstrate that a simple feed-forward model of spatial-frequency preference, unlike that for orientation preference, does not generate a faithful representation when amplified by recurrent interactions in V1. We then introduce the idea that cortico-geniculate feedback modulates LGN activity to generate a faithful representation, thus providing a new functional interpretation of the role of this feedback pathway. Using linear filter theory, we show that if the feedback from a cortical cell is taken to be approximately equal to the reciprocal of the corresponding feed-forward receptive field (in the two-dimensional Fourier domain), then the mismatch between the feed-forward and cortical frequency representations is eliminated. We therefore predict that cortico-geniculate feedback connections innervate the LGN in a pattern determined by the orientation and spatial-frequency biases of feed-forward receptive fields. Finally, we show how recurrent cortical interactions can generate cross-orientation suppression. PMID:14561324

Neural coding underlying the cue preference for celestial orientation

PubMed Central

el Jundi, Basil; Warrant, Eric J.; Byrne, Marcus J.; Khaldy, Lana; Baird, Emily; Smolka, Jochen; Dacke, Marie

2015-01-01

Diurnal and nocturnal African dung beetles use celestial cues, such as the sun, the moon, and the polarization pattern, to roll dung balls along straight paths across the savanna. Although nocturnal beetles move in the same manner through the same environment as their diurnal relatives, they do so when light conditions are at least 1 million-fold dimmer. Here, we show, for the first time to our knowledge, that the celestial cue preference differs between nocturnal and diurnal beetles in a manner that reflects their contrasting visual ecologies. We also demonstrate how these cue preferences are reflected in the activity of compass neurons in the brain. At night, polarized skylight is the dominant orientation cue for nocturnal beetles. However, if we coerce them to roll during the day, they instead use a celestial body (the sun) as their primary orientation cue. Diurnal beetles, however, persist in using a celestial body for their compass, day or night. Compass neurons in the central complex of diurnal beetles are tuned only to the sun, whereas the same neurons in the nocturnal species switch exclusively to polarized light at lunar light intensities. Thus, these neurons encode the preferences for particular celestial cues and alter their weighting according to ambient light conditions. This flexible encoding of celestial cue preferences relative to the prevailing visual scenery provides a simple, yet effective, mechanism for enabling visual orientation at any light intensity. PMID:26305929

Neural coding underlying the cue preference for celestial orientation.

PubMed

el Jundi, Basil; Warrant, Eric J; Byrne, Marcus J; Khaldy, Lana; Baird, Emily; Smolka, Jochen; Dacke, Marie

2015-09-08

Diurnal and nocturnal African dung beetles use celestial cues, such as the sun, the moon, and the polarization pattern, to roll dung balls along straight paths across the savanna. Although nocturnal beetles move in the same manner through the same environment as their diurnal relatives, they do so when light conditions are at least 1 million-fold dimmer. Here, we show, for the first time to our knowledge, that the celestial cue preference differs between nocturnal and diurnal beetles in a manner that reflects their contrasting visual ecologies. We also demonstrate how these cue preferences are reflected in the activity of compass neurons in the brain. At night, polarized skylight is the dominant orientation cue for nocturnal beetles. However, if we coerce them to roll during the day, they instead use a celestial body (the sun) as their primary orientation cue. Diurnal beetles, however, persist in using a celestial body for their compass, day or night. Compass neurons in the central complex of diurnal beetles are tuned only to the sun, whereas the same neurons in the nocturnal species switch exclusively to polarized light at lunar light intensities. Thus, these neurons encode the preferences for particular celestial cues and alter their weighting according to ambient light conditions. This flexible encoding of celestial cue preferences relative to the prevailing visual scenery provides a simple, yet effective, mechanism for enabling visual orientation at any light intensity.

Curriculum Orientations of Virtual Teachers

ERIC Educational Resources Information Center

Singleton, Nicole Y.

2013-01-01

This study explored the curriculum orientation preferences of K-12 public school teachers who provided instruction in virtual settings (n = 47) in a midwestern state. Curriculum orientations were explored using a mixed-methods design. Quantitative assessments data revealed a pattern of curriculum orientations similar to teachers working in…

Preferred orientation of albumin adsorption on a hydrophilic surface from molecular simulation.

PubMed

Hsu, Hao-Jen; Sheu, Sheh-Yi; Tsay, Ruey-Yug

2008-12-01

In general, non-specific protein adsorption follows a two-step procedure, i.e. first adsorption onto a surface in native form, and a subsequent conformational change on the surface. In order to predict the subsequent conformational change, it is important to determine the preferred orientation of an adsorbed protein in the first step of the adsorption. In this work, a method based on finding the global minimum of the interaction potential energy of an adsorbed protein has been developed to delineate the preferred orientations for the adsorption of human serum albumin (HSA) on a model surface with a hydrophilic self-assembled monolayer (SAM). For computational efficiency, solvation effects were greatly simplified by only including the dampening of electrostatic effects while neglecting contributions due to the competition of water molecules for the functional groups on the surface. A contour map obtained by systematic rotation of a molecule in conjunction with perpendicular motion to the surface gives the minimum interaction energy of the adsorbed molecule at various adsorption orientations. Simulation results show that for an -OH terminated SAM surface, a "back-on" orientation of HSA is the preferred orientation. The projection area of this adsorption orientation corresponds with the "triangular-side-on" adsorption of a heart shaped HSA molecule. The method proposed herein is able to provide results which are consistent with those predicted by Monte Carlo (MC) simulations with a substantially less computing cost. The high computing efficiency of the current method makes it possible to be implemented as a design tool for the control of protein adsorption on surfaces; however, before this can be fully realized, these methods must be further developed to enable interaction free energy to be calculated in place of potential energy, along with a more realistic representation of solvation effects.

Effect of solvent volume on the physical properties of undoped and fluorine doped tin oxide films deposited using a low-cost spray technique

NASA Astrophysics Data System (ADS)

Muruganantham, G.; Ravichandran, K.; Saravanakumar, K.; Ravichandran, A. T.; Sakthivel, B.

2011-12-01

Undoped and fluorine doped tin oxide films were deposited from starting solutions having different values of solvent volume (10-50 ml) by employing a low cost and simplified spray technique using perfume atomizer. X-ray diffraction studies showed that there was a change in the preferential orientation from (2 1 1) plane to (1 1 0) plane as the volume of the solvent was increased. The sheet resistance ( Rsh) of undoped SnO 2 film was found to be minimum (13.58 KΩ/□) when the solvent volume was lesser (10 ml) and there was a sharp increase in Rsh for higher values of solvent volume. Interestingly, it was observed that while the Rsh increases sharply with the increase in solvent volume for undoped SnO 2 films, it decreases gradually in the case of fluorine doped SnO 2 films. The quantitative analysis of EDAX confirmed that the electrical resistivity of the sprayed tin oxide film was mainly governed by the number of oxygen vacancies and the interstitial incorporation of Sn atoms which in turn was governed by the impinging flux on the hot substrate. The films were found to have good optical characteristics suitable for opto-electronic devices.

Relationship between open-circuit voltage in Cu(In,Ga)Se2 solar cell and peak position of (220/204) preferred orientation near its absorber surface

NASA Astrophysics Data System (ADS)

Chantana, J.; Watanabe, T.; Teraji, S.; Kawamura, K.; Minemoto, T.

2013-11-01

Cu(In,Ga)Se2 (CIGS) absorbers with various Ga/III, Ga/(In+Ga), profiles are prepared by the so-called "multi-layer precursor method" using multi-layer co-evaporation of material sources. It is revealed that open-circuit voltage (VOC) of CIGS solar cell is primarily dependent on averaged Ga/III near the surface of its absorber. This averaged Ga/III is well predicted by peak position of (220/204) preferred orientation of CIGS film near its surface investigated by glancing-incidence X-ray diffraction with 0.1° incident angle. Finally, the peak position of (220/204) preferred orientation is proposed as a measure of VOC before solar cell fabrication.

Oriented molecular sieve membranes by heteroepitaxial growth.

PubMed

Jeong, Hae-Kwon; Krohn, John; Sujaoti, Khristina; Tsapatsis, Michael

2002-11-06

Heteroepitaxial growth of titanosilicates (ETS-10 and ETS-4) is reported. Using this heteroepitaxial growth, oriented ETS-10/-4 membranes have been fabricated, demonstrating a novel way to achieve preferred orientation of molecular sieve films.

A comparative study of TiN and TiC: Oxidation resistance and retention of xenon at high temperature and under degraded vacuum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gavarini, S.; Bes, R.; Millard-Pinard, N.

2011-01-01

Dense TiN and TiC samples were prepared by hot pressing using micrometric powders. Xenon species (simulating rare gas fission products) were then implanted into the ceramics. The samples were annealed for 1 h at 1500 deg. C under several degraded vacuums with P{sub O{sub 2}} varying from 10{sup -6} to 2x10{sup -4} mbars. The oxidation resistance of the samples and their retention properties with respect to preimplanted xenon species were analyzed using scanning electron microscopy, grazing incidence x-ray diffraction, Rutherford backscattering spectrometry, and nuclear backscattering spectrometry. Results indicate that TiC is resistant to oxidation and does not release xenon formore » P{sub O{sub 2{<=}}}6x10{sup -6} mbars. When P{sub O{sub 2}} increases, geometric oxide crystallites appear at the surface depending on the orientation and size of TiC grains. These oxide phases are Ti{sub 2}O{sub 3}, Ti{sub 3}O{sub 5}, and TiO{sub 2}. Apparition of oxide crystallites is associated with the beginning of xenon release. TiC surface is completely covered by the oxide phases at P{sub O{sub 2}}=2x10{sup -4} mbars up to a depth of 3 {mu}m and the xenon is then completely released. For TiN samples, the results show a progressive apparition of oxide crystallites (Ti{sub 3}O{sub 5} mainly) at the surface when P{sub O{sub 2}} increases. The presence of the oxide crystallites is also directly correlated with xenon release, the more oxide crystallites are growing the more xenon is released. TiN surface is completely covered by an oxide layer at P{sub O{sub 2}}=2x10{sup -4} mbars up to 1 {mu}m. A correlation between the initial fine microstructure of TiN and the properties of the growing layer is suggested.« less

Leadership styles in nursing management: preferred and perceived.

PubMed

Sellgren, Stina; Ekvall, Göran; Tomson, Göran

2006-07-01

The aim was to explore nursing leadership regarding what nurse managers and subordinates see as important and to explore subordinates' opinions of their nurse manager's performance in reality. Background The manager's style can be fundamental for subordinates' acceptance of change and in motivating them to achieve stated visions and goals and high quality of care. Nurse managers (n=77) and 10 of each included nurse manager's subordinates received a questionnaire to assess 'preferred' leadership behaviour in three dimensions: change, production and employee/relation orientations. The same questionnaire was used to assess subordinates' opinions of their manager's leadership behaviour. There are statistically significant differences in opinions of preferred leadership between managers and subordinates, especially related to production and relation orientation. The subordinates' perception of real leadership behaviour has lower mean values than their preferred leadership behaviour in all three dimensions. Subordinates prefer managers with more clearly expressed leadership behaviour than managers themselves prefer and demonstrate.

An exploratory study of death anxiety and trainees' choice of theoretical orientation.

PubMed

Belviso, Francesco; Gaubatz, Michael D

2013-01-01

This study investigated the association between therapist trainees' death anxiety and their preference for "objective" (i.e., quantitative and rational) over "subjective" (i.e., experiential and symbolic) theoretical orientations. In this correlational investigation, 303 clinical psychology and counseling trainees at a Midwestern school of professional psychology completed instruments assessing their fear of personal death and their endorsement of superordinate dimensions of psychotherapy orientations. As hypothesized, trainees who reported higher levels of death anxiety displayed a stronger preference for objective over subjective orientations, a relationship that was found in post hoc analyses to be particularly salient for male trainees. These findings suggest that trainees' death anxiety, and their attempts to control it, could influence their choice of a theoretical orientation. Potential implications for training institutions are discussed.

An exploratory study of death anxiety and trainees' choice of theoretical orientation.

PubMed

Belviso, Francesco; Gaubatz, Michael D

This study investigated the association between therapist-trainees' death anxiety and their preference for "objective" (i.e., quantitative and rational) over "subjective" (i.e., experiential and symbolic) theoretical orientations. In this correlational investigation, 303 clinical psychology and counseling trainees at a Midwestern school of professional psychology completed instruments assessing their fear of personal death and their endorsement of superordinate dimensions of psychotherapy orientations. As hypothesized, trainees who reported higher levels of death anxiety displayed a stronger preference for objective over subjective orientations, a relationship that was found in post-hoc analyses to be particularly salient for male trainees. These findings suggest that trainees' death anxiety, and their attempts to control it, could influence their choice of a theoretical orientation. Potential implications for training institutions are discussed.

Asymmetric information and user orientation in general practice: Exploring the agency relationship in a best-worst scaling study.

PubMed

Pedersen, Line Bjørnskov; Hess, Stephane; Kjær, Trine

2016-12-01

This study uses a best-worst scaling experiment to test whether general practitioners (GPs) act as perfect agents for the patients in the consultation; and if not, whether this is due to asymmetric information and/or other motivations than user orientation. Survey data were collected from 775 GPs and 1379 Danish citizens eliciting preferences for a consultation. Sequential models allowing for within-person preference heterogeneity and heteroskedasticity between best and worst choices were estimated. We show that GPs do not always act as perfect agents and that this non-alignment stems from GPs being both unable and unwilling to do so. Unable since GPs have imperfect information about patients' preferences, and unwilling since they are also motivated by other factors than user orientation. Our findings highlight the need for multi-pronged strategies targeting different motivational factors to ensure that GPs act in correspondence with patients' preferences in areas where alignment is warranted. Copyright © 2016 Elsevier B.V. All rights reserved.

Engineering and characterization of aluminum oxide-based Magnetic Tunnel Junctions

NASA Astrophysics Data System (ADS)

Ji, Chengxiang

Magnetic Tunnel Junctions (MTJs) consisting of two ferromagnetic layers separated by an insulator layer have attracted great interest due to their applications in magnetic read heads and potential applications in magnetic random access memory. Materials science plays an important role in the performance of the MTJs. The goal of this research was to focus on how the materials properties affect the tunneling magnetoresistance (TMR) of AlOx-based MTJs with (Co, Fe) electrodes. A method was developed to fabricate epitaxial (Co, Fe) (001) thin films on Si substrates using TiN buffer and a novel processing technique in order to achieve smooth interfaces between the electrode and the AlOx tunnel barrier. The (Co, Fe) thin films with other orientations, i.e. (110) and (211), were also grown on TiN buffered substrates of Si (111) and (011). Numerous MTJs with epitaxial bottom electrode were fabricated to investigate the effect of the materials properties of the (Co, Fe) electrode on the TMR of these junctions. A strain induced TMR enhancement was discovered, where the trend of increasing TMR of the MTJs is the same as that of the strain of the bottom electrode. The strain was originated from the lattice mismatch between (Co, Fe) electrode and the buffer layers in the MTJs, which will vary with annealing temperatures. Since the interface roughness and the barrier properties were the same within the uncertainties of the measurement, this TMR enhancement was attributed to the presence of strain. The TMR values were also compared for MTJs with the bottom electrode in the (001), (110) and (211) orientations. The anisotropic property of (Co, Fe) was confirmed and the (001) orientation has larger spin polarization than the (110) and (211) orientations. By careful manipulation of the bottom electrode, including strain, roughness and orientation, 77% TMR was obtained for AlOx-based MTJs. The phase transformation of Pt0.5-xMn0.5+x from fcc to Ll0 was investigated. The experimental results showed the onset temperature for phase transformation increase as the composition deviates from stoichiometry but slows down the kinetics of transformation.

Electronic structure and its external electric field modulation of PbPdO2 ultrathin slabs with (002) and (211) preferred orientations.

PubMed

Yang, Yanmin; Zhong, Kehua; Xu, Guigui; Zhang, Jian-Min; Huang, Zhigao

2017-07-31

The Electronic structure of PbPdO 2 with (002) and (211) preferred orientations were investigated using first-principles calculation. The calculated results indicate that, (002) and (211) orientations exhibit different electric field dependence of band-gap and carrier concentration. The small band gap and more sensitive electric field modulation of band gap were found in (002) orientation. Moreover, the electric field modulation of the resistivity up to 3-4 orders of magnitude is also observed in (002) slab, which reveals that origin of colossal electroresistance. Lastly, electric field modulation of band gap is well explained. This work should be significant for repeating the colossal electroresistance.

Experience modulates the influence of gonadal hormones on sexual orientation of male rats.

PubMed

Matuszczyk, J V; Larsson, K

1994-03-01

The aim of this study was to investigate whether heterosexual experience influences the male's partner preference and the role of gonadal hormones, including several androgens and estradiol, on female-oriented behavior. In the first experiment, the animals were exposed to a four-stimuli test situation including a sexually active male, a castrated male, an estrous female, and an ovariectomized (ovx) female. Castrated naive and experienced male rats were implanted with either testosterone (T), estradiol (E2), or an empty tubing (blank) and compared to intact naive and experienced male rats. None of the naive animals, whether castrated or intact, showed a consistent preference for any of the four stimuli. Whereas when sexually experienced, only intact and T-treated males showed a female-oriented preference. In the second experiment, the animals were allowed to choose between an active male and an estrous female. Castrated naive male rats were implanted with either T, E2, or DHT, or injected daily SC with the synthetic nonaromatizable androgen, methyltrienelone (R 1881). Two groups of intact males, one consisting of experienced and the other of naive animals, were also included in this experiment. The experienced intact males showed a significant preference for the estrous female, while the intact naive males showed no preference for either of the two stimuli. After the animals had gained heterosexual experience, intact and androgen-treated males showed a significant preference for the female. Neither the administration of R 1881 nor E2 promoted a female-oriented behavior.(ABSTRACT TRUNCATED AT 250 WORDS)

Curriculum Design Orientations Preference Scale of Teachers: Validity and Reliability Study

ERIC Educational Resources Information Center

Bas, Gokhan

2013-01-01

The purpose of this study was to develop a valid and reliable scale for preferences of teachers in regard of their curriculum design orientations. Because there was no scale development study similar to this one in Turkey, it was considered as an urgent need to develop such a scale in the study. The sample of the research consisted of 300…

Temporal-frequency tuning of cross-orientation suppression in the cat striate cortex.

PubMed

Allison, J D; Smith, K R; Bonds, A B

2001-01-01

A sinusoidal mask grating oriented orthogonally to and superimposed onto an optimally oriented base grating reduces a cortical neuron's response amplitude. The spatial selectivity of cross-orientation suppression (XOR) has been described, so for this paper we investigated the temporal properties of XOR. We recorded from single striate cortical neurons (n = 72) in anesthetized and paralyzed cats. After quantifying the spatial and temporal characteristics of each cell's excitatory response to a base grating, we measured the temporal-frequency tuning of XOR by systematically varying the temporal frequency of a mask grating placed at a null orientation outside of the cell's excitatory orientation domain. The average preferred temporal frequency of the excitatory response of the neurons in our sample was 3.8 (+/- 1.5 S.D.) Hz. The average cutoff frequency for the sample was 16.3 (+/- 1.7) Hz. The average preferred temporal frequency (7.0 +/- 2.6 Hz) and cutoff frequency (20.4 +/- 6.9 Hz) of the XOR were significantly higher. The differences averaged 1.1 (+/- 0.6) octaves for the peaks and 0.3 (+/- 0.4) octaves for the cutoffs. The XOR mechanism's preference for high temporal frequencies suggests a possible extrastriate origin for the effect and could help explain the low-pass temporal-frequency response profile displayed by most striate cortical neurons.

The Representation of Orientation in Macaque V2: Four Stripes Not Three

PubMed Central

Felleman, Daniel J.; Lim, Heejin; Xiao, Youping; Wang, Yi; Eriksson, Anastasia; Parajuli, Arun

2015-01-01

Area V2 of macaque monkeys is traditionally thought to consist of 3 distinct functional compartments with characteristic cortical connections and functional properties. Orientation selectivity is one property that has frequently been used to distinguish V2 stripes, however, this receptive field property has been found in a high percentage of neurons across V2 compartments. Using quantitative intrinsic cortical imaging, we derived maps of preferred orientation, orientation selectivity, and orientation gradient in thin stripes, thick stripes, and interstripes in area V2. Orientation-selective responses were found in each V2 stripe, but the magnitude and organization of orientation selectivity differed significantly from stripe to stripe. Remarkably, the 2 pale stripes flanking each cytochrome oxidase dense stripe differed significantly in their representation of orientation resulting in their distinction as type-I and type-II interstripes. V2 orientation maps are characterized by clockwise and anticlockwise “orientation pinwheels”, but unlike V1, they are not homogeneously distributed across V2. Furthermore, V2 stripes contain large-scale sequences of preferred orientation. These analyses demonstrate that V2 consists of 4 distinct functional compartments; thick stripes and type-II interstripes, which are strongly orientation selective and thin stripes and type-I interstripes, which are significantly less selective for orientation and exhibit larger orientation gradient magnitudes. PMID:24614951

The Degree of Early Life Stress Predicts Decreased Medial Prefrontal Activations and the Shift from Internally to Externally Guided Decision Making: An Exploratory NIRS Study during Resting State and Self-Oriented Task

PubMed Central

Nakao, Takashi; Matsumoto, Tomoya; Morita, Machiko; Shimizu, Daisuke; Yoshimura, Shinpei; Northoff, Georg; Morinobu, Shigeru; Okamoto, Yasumasa; Yamawaki, Shigeto

2013-01-01

Early life stress (ELS), an important risk factor for psychopathology in mental disorders, is associated neuronally with decreased functional connectivity within the default mode network (DMN) in the resting state. Moreover, it is linked with greater deactivation in DMN during a working memory task. Although DMN shows large amplitudes of very low-frequency oscillations (VLFO) and strong involvement during self-oriented tasks, these features’ relation to ELS remains unclear. Therefore, our preliminary study investigated the relationship between ELS and the degree of frontal activations during a resting state and self-oriented task using near-infrared spectroscopy (NIRS). From 22 healthy participants, regional hemodynamic changes in 43 front-temporal channels were recorded during 5 min resting states, and execution of a self-oriented task (color-preference judgment) and a control task (color-similarity judgment). Using a child abuse and trauma scale, ELS was quantified. We observed that ELS showed a negative correlation with medial prefrontal cortex (MPFC) activation during both resting state and color-preference judgment. In contrast, no significant correlation was found between ELS and MPFC activation during color-similarity judgment. Additionally, we observed that ELS and the MPFC activation during color-preference judgment were associated behaviorally with the rate of similar color choice in preference judgment, which suggests that, for participants with higher ELS, decisions in the color-preference judgment were based on an external criterion (color similarity) rather than an internal criterion (subjective preference). Taken together, our neuronal and behavioral findings show that high ELS is related to lower MPFC activation during both rest and self-oriented tasks. This is behaviorally manifest in an abnormal shift from internally to externally guided decision making, even under circumstances where internal guidance is required. PMID:23840186

Computational design of materials for solar hydrogen generation

NASA Astrophysics Data System (ADS)

Umezawa, Naoto

Photocatalysis has a great potential for the production of hydrogen from aquerous solution under solar light. In this talk, two different approaches toward the computational materials desing for solar hydrogen generation will be presented. Tin (Sn), which has two major oxidation states, Sn2+ and Sn4+, is abundant on the earth's crust. Recently, visible-light responsive photocatalytc H2 evolution reaction was identified over a mixed valence tin oxide Sn3O4. We have carried out crystal structure prediction for mixed valence tin oxides in different atomic compositions under ambient pressure condition using advanced computational methods based on the evolutionary crystal-structure search and density-functional theory. The predicted novel crystal structures realize the desirable band gaps and band edge positions for H2 evolution under visible light irradiation. It is concluded that multivalent tin oxides have a great potential as an abundant, cheap and environmentally-benign solar-energy conversion photofunctional materials. Transition metal doping is effective for sensitizing SrTiO3 under visible light. We have theoretically investigated the roles of the doped Cr in STO based on hybrid density-functional calculations. Cr atoms are preferably substituting for Ti under any equilibrium growth conditions. The lower oxidation state Cr3+, which is stabilized under an n-type condition of STO, is found to be advantageous for the photocatalytic performance. It is firther predicted that lanthanum is the best codopant for stabilizing the favorable oxidation state, Cr3+. The prediction was validated by our experiments that La and Cr co-doped STO shows the best performance among examined samples. This work was supported by the Japan Science and Technology Agency (JST) Precursory Research for Embryonic Science and Technology (PRESTO) and International Research Fellow program of Japan Society for the Promotion of Science (JSPS) through project P14207.

The role of Tin Oxide Concentration on The X-ray Diffraction, Morphology and Optical Properties of In2O3:SnO2 Thin Films

NASA Astrophysics Data System (ADS)

Hasan, Bushra A.; Abdallah, Rusul M.

2018-05-01

Alloys were performed from In2O3 doped SnO2 with different doping ratio by quenching from the melt technique. Pulsed Laser Deposition PLD was used to deposit thin films of different doping ratio In2O3 : SnO2 (0, 1, 3, 5, 7 and 9 % wt.) on glass substrate at ambient temperature under vacuum of 10-3 bar thickness of ∼100nm. The structural type,grain size and morphology of the prepared alloys compounds and thin films were examined using X-ray diffraction and atomic force microscopy. The results showed that all alloys have polycrystalline structures and the peaks belonged to the preferred plane for crystal growth were identical with the ITO (Indium – Tin –Oxide) standard cards also another peaks were observed belonged to SnO2 phase. The structures of thin films was also polycrystalline, and the predominate peaks are identical with standard cards ITO. On the other side the prepared thin films declared decrease a reduction of degree of crystallinity with the increase of doping ratio. Atomic Force Microscopy AFM measurements showed the average grain size and average surface roughness exhibit to change in systematic manner with the increase of doping ratio with tin oxide. The optical measurements show that the In2O3:SnO2 thin films have a direct energy gap Eg opt in the first stage decreases with the increase of doping ratio and then get to increase with further increase of doping ration, whereas reverse to that the optical constants such as refractive index (n), extinction coefficient (k) and dielectric constant (εr, εi) have a regular increase with the doping ratio by tin oxide and then decreases.

Effects of temperature, algae biomass and ambient nutrient on the absorption of dissolved nitrogen and phosphate by Rhodophyte Gracilaria asiatica

NASA Astrophysics Data System (ADS)

Du, Rongbin; Liu, Liming; Wang, Aimin; Wang, Yongqiang

2013-03-01

Gracilaria asiatica, being highly efficient in nutrient absorption, is cultivated in sea cucumber ponds to remove nutrients such as nitrogen and phosphate. It was cultured in a laboratory simulating field conditions, and its nutrient absorption was measured to evaluate effects of environmental conditions. Ammonia nitrogen (AN), nitrate nitrogen (NN), total inorganic nitrogen (TIN), and soluble reactive phosphorus (SRP) uptake rate and removal efficiency were determined in a 4×2 factorial design experiment in water temperatures ( T) at 15°C and 25°C, algae biomass (AB) at 0.5 g/L and 1.0 g/L, total inorganic nitrogen (TIN) at 30 μmol/L and 60 μmol/L, and soluble reactive phosphorus (SRP) at 3 and 6 μmol/L. AB and ambient TIN or SRP levels significantly affected uptake rate and removal efficiency of AN, NN, TIN, and SRP ( P< 0.001). G. asiatica in AB of 0.5 g/L showed higher uptake rate and lower removal efficiency relative to that with AB of 1.0 g/L. Nitrogen and phosphorus uptake rate rose with increasing ambient nutrient concentrations; nutrient removal efficiency decreased at higher environmental nutrient concentrations. The algae preferred to absorb AN to NN. Uptake rates of AN, NN, and SRP were significantly affected by temperature ( P < 0.001); uptake rate was higher for the 25°C group than for the 15°C group at the initial experiment stage. Only the removal efficiency of AN and SRP showed a significant difference between the two temperature groups ( P< 0.01). The four factors had significant interactive effects on absorption of N and P, implying that G. asiatica has great bioremedial potential in sea cucumber culture ponds.

Structural hysteresis in dragline spider silks induced by supercontraction: an X-ray fiber micro-diffraction study

DOE PAGES

Sampath, Sujatha; Yarger, Jeffery L.

2014-11-27

Interaction with water causes shrinkage and significant changes in the structure of spider dragline silks, which has been referred to as supercontraction in the literature. Preferred orientation or alignment of protein chains with respect to the fiber axis is extensively changed during this supercontraction process. Synchrotron X-ray micro-fiber diffraction experiments have been performed on Nephila clavipes and Argiope aurantia major and minor ampullate dragline spider fibers in the native dry, contracted (by immersion in water) and restretched (from contracted) states. Changes in the orientation of β-sheet nanocrystallites and the oriented component of the amorphous network have been determined from wide-anglemore » X-ray diffraction patterns. While both the crystalline and amorphous components lose preferred orientation on wetting with water, the nano-crystallites regain their orientation on wet-restretching, whereas the oriented amorphous components only partially regain their orientation. Dragline major ampullate silks in both the species contract more than their minor ampullate silks.« less

Relationship between open-circuit voltage in Cu(In,Ga)Se{sub 2} solar cell and peak position of (220/204) preferred orientation near its absorber surface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chantana, J., E-mail: jakapan@fc.ritsumei.ac.jp; Minemoto, T.; Watanabe, T.

2013-11-25

Cu(In,Ga)Se{sub 2} (CIGS) absorbers with various Ga/III, Ga/(In+Ga), profiles are prepared by the so-called “multi-layer precursor method” using multi-layer co-evaporation of material sources. It is revealed that open-circuit voltage (V{sub OC}) of CIGS solar cell is primarily dependent on averaged Ga/III near the surface of its absorber. This averaged Ga/III is well predicted by peak position of (220/204) preferred orientation of CIGS film near its surface investigated by glancing-incidence X-ray diffraction with 0.1° incident angle. Finally, the peak position of (220/204) preferred orientation is proposed as a measure of V{sub OC} before solar cell fabrication.

Strong quantum scarring by local impurities

PubMed Central

Luukko, Perttu J. J.; Drury, Byron; Klales, Anna; Kaplan, Lev; Heller, Eric J.; Räsänen, Esa

2016-01-01

We discover and characterise strong quantum scars, or quantum eigenstates resembling classical periodic orbits, in two-dimensional quantum wells perturbed by local impurities. These scars are not explained by ordinary scar theory, which would require the existence of short, moderately unstable periodic orbits in the perturbed system. Instead, they are supported by classical resonances in the unperturbed system and the resulting quantum near-degeneracy. Even in the case of a large number of randomly scattered impurities, the scars prefer distinct orientations that extremise the overlap with the impurities. We demonstrate that these preferred orientations can be used for highly efficient transport of quantum wave packets across the perturbed potential landscape. Assisted by the scars, wave-packet recurrences are significantly stronger than in the unperturbed system. Together with the controllability of the preferred orientations, this property may be very useful for quantum transport applications. PMID:27892510

Strong quantum scarring by local impurities

NASA Astrophysics Data System (ADS)

Luukko, Perttu J. J.; Drury, Byron; Klales, Anna; Kaplan, Lev; Heller, Eric J.; Räsänen, Esa

2016-11-01

We discover and characterise strong quantum scars, or quantum eigenstates resembling classical periodic orbits, in two-dimensional quantum wells perturbed by local impurities. These scars are not explained by ordinary scar theory, which would require the existence of short, moderately unstable periodic orbits in the perturbed system. Instead, they are supported by classical resonances in the unperturbed system and the resulting quantum near-degeneracy. Even in the case of a large number of randomly scattered impurities, the scars prefer distinct orientations that extremise the overlap with the impurities. We demonstrate that these preferred orientations can be used for highly efficient transport of quantum wave packets across the perturbed potential landscape. Assisted by the scars, wave-packet recurrences are significantly stronger than in the unperturbed system. Together with the controllability of the preferred orientations, this property may be very useful for quantum transport applications.

Strong quantum scarring by local impurities.

PubMed

Luukko, Perttu J J; Drury, Byron; Klales, Anna; Kaplan, Lev; Heller, Eric J; Räsänen, Esa

2016-11-28

We discover and characterise strong quantum scars, or quantum eigenstates resembling classical periodic orbits, in two-dimensional quantum wells perturbed by local impurities. These scars are not explained by ordinary scar theory, which would require the existence of short, moderately unstable periodic orbits in the perturbed system. Instead, they are supported by classical resonances in the unperturbed system and the resulting quantum near-degeneracy. Even in the case of a large number of randomly scattered impurities, the scars prefer distinct orientations that extremise the overlap with the impurities. We demonstrate that these preferred orientations can be used for highly efficient transport of quantum wave packets across the perturbed potential landscape. Assisted by the scars, wave-packet recurrences are significantly stronger than in the unperturbed system. Together with the controllability of the preferred orientations, this property may be very useful for quantum transport applications.

A cross-cultural perspective on the preference for potential effect: an individual participant data (IPD) meta-analysis approach.

PubMed

Sun, Xiaomin; Xu, Dan; Luo, Fang; Wei, Zihan; Wei, Cong; Xue, Gang

2015-01-01

A recent paper [Tormala ZL, Jia JS, Norton MI (2012). The preference for potential. Journal of personality and social psychology, 103: 567-583] demonstrated that persons often prefer potential rather than achievement when evaluating others, because information regarding potential evokes greater interest and processing, resulting in more favorable evaluations. This research aimed to expand on this finding by asking two questions: (a) Is the preference for potential effect replicable in other cultures? (b) Is there any other mechanism that accounts for this preference for potential? To answer these two questions, we replicated Tormala et al.'s study in multiple cities (17 studies with 1,128 participants) in China using an individual participant data (IPD) meta-analysis approach to test our hypothesis. Our results showed that the preference for potential effect found in the US is also robust in China. Moreover, we also found a pro-youth bias behind the preference for potential effect. To be specific, persons prefer a potential-oriented applicant rather than an achievement-oriented applicant, partially because they believe that the former is younger than the latter.

Plasticity of orientation preference maps in the visual cortex of adult cats.

PubMed

Godde, Ben; Leonhardt, Ralph; Cords, Sven M; Dinse, Hubert R

2002-04-30

In contrast to the high degree of experience-dependent plasticity usually exhibited by cortical representational maps, a number of experiments performed in visual cortex suggest that the basic layout of orientation preference maps is only barely susceptible to activity-dependent modifications. In fact, most of what we know about activity-dependent plasticity in adults comes from experiments in somatosensory, auditory, or motor cortex. Applying a stimulation protocol that has been proven highly effective in other cortical areas, we demonstrate here that enforced synchronous cortical activity induces major changes of orientation preference maps (OPMs) in adult cats. Combining optical imaging of intrinsic signals and electrophysiological single-cell recordings, we show that a few hours of intracortical microstimulation (ICMS) lead to an enlargement of the cortical representational zone at the ICMS site and an extensive restructuring of the entire OPM layout up to several millimeters away, paralleled by dramatic changes of pinwheel numbers and locations. At the single-cell level, we found that the preferred orientation was shifted toward the orientation of the ICMS site over a region of up to 4 mm. Our results show that manipulating the synchronicity of cortical activity locally without invoking training, attention, or reinforcement, OPMs undergo large-scale reorganization reminiscent of plastic changes observed for nonvisual cortical maps. However, changes were much more widespread and enduring. Such large-scale restructuring of the visual cortical networks indicates a substantial capability for activity-dependent plasticity of adult visual cortex and may provide the basis for cognitive learning processes.

Student Orientations to Independent Learning.

ERIC Educational Resources Information Center

Jones, Alice; Jones, Douglas

1996-01-01

A study investigated the relationship of 46 college students' preferred teaching method (conventional lecture versus independent study package) and their own approaches to study (surface, deep, achieving). Results indicated that while students preferred the conventional lecture method, preference did not correlate with their study approach and…

GEMAS: Spatial pattern analysis of Ni by using digital image processing techniques on European agricultural soil data

NASA Astrophysics Data System (ADS)

Jordan, Gyozo; Petrik, Attila; De Vivo, Benedetto; Albanese, Stefano; Demetriades, Alecos; Sadeghi, Martiya

2017-04-01

Several studies have investigated the spatial distribution of chemical elements in topsoil (0-20 cm) within the framework of the EuroGeoSurveys Geochemistry Expert Group's 'Geochemical Mapping of Agricultural and Grazing Land Soil' project . Most of these studies used geostatistical analyses and interpolated concentration maps, Exploratory and Compositional Data and Analysis to identify anomalous patterns. The objective of our investigation is to demonstrate the use of digital image processing techniques for reproducible spatial pattern recognition and quantitative spatial feature characterisation. A single element (Ni) concentration in agricultural topsoil is used to perform the detailed spatial analysis, and to relate these features to possible underlying processes. In this study, simple univariate statistical methods were implemented first, and Tukey's inner-fence criterion was used to delineate statistical outliers. The linear and triangular irregular network (TIN) interpolation was used on the outlier-free Ni data points, which was resampled to a 10*10 km grid. Successive moving average smoothing was applied to generalise the TIN model and to suppress small- and at the same time enhance significant large-scale features of Nickel concentration spatial distribution patterns in European topsoil. The TIN map smoothed with a moving average filter revealed the spatial trends and patterns without losing much detail, and it was used as the input into digital image processing, such as local maxima and minima determination, digital cross sections, gradient magnitude and gradient direction calculation, second derivative profile curvature calculation, edge detection, local variability assessment, lineament density and directional variogram analyses. The detailed image processing analysis revealed several NE-SW, E-W and NW-SE oriented elongated features, which coincide with different spatial parameter classes and alignment with local maxima and minima. The NE-SW oriented linear pattern is the dominant feature to the south of the last glaciation limit. Some of these linear features are parallel to the suture zone of the Iapetus Ocean, while the others follow the Alpine and Carpathian Chains. The highest variability zones of Ni concentration in topsoil are located in the Alps and in the Balkans where mafic and ultramafic rocks outcrop. The predominant NE-SW oriented pattern is also captured by the strong anisotropy in the semi-variograms in this direction. A single major E-W oriented north-facing feature runs along the southern border of the last glaciation zone. This zone also coincides with a series of local maxima in Ni concentration along the glaciofluvial deposits. The NW-SE elongated spatial features are less dominant and are located in the Pyrenees and Scandinavia. This study demonstrates the efficiency of systematic image processing analysis in identifying and characterising spatial geochemical patterns that often remain uncovered by the usual visual map interpretation techniques.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Y.W.; Labouriau, A.; Taylor, C.M.

Dynamics and structure of tri-n-butyltin fluoride in n-hexane solutions were probed using (tin-119) nuclear magnetic resonance spin relaxation methodologies. Significant relaxation-induced polarization transfer effects were observed and exploited. The experimental observations indicate that the tri-n-butyl fluoride exists in a polymeric form in solution. For a 0.10% (w/w) solution at 25 [degree]C, NMR reveals significant orientational/exchange relaxation on both the microsecond and nanosecond time scales. Solution-state and solid-state parameters are compared and contrasted. 26 refs., 3 figs., 1 tab.

Preference Versus Prejudice: A Multimethod Analysis of Children's Discrepant Racial Choices

ERIC Educational Resources Information Center

Teplin, Linda A.

1977-01-01

A study compared 398 children's racial preferences in an imaginary setting with their responses in a more reality-oriented situation. Discrepant responses to the two measurements indicate that racial/ethnic preferences in imagination are neither indicative nor predictive of prejudicial behavior. (Author)

Sexual orientation and shifts in preferences for a partner's body attributes in short-term versus long-term mating contexts.

PubMed

Lucas, Margery; Koff, Elissa; Grossmith, Samantha; Migliorini, Robyn

2011-06-01

This study assessed the effects of short- and long-term mating contexts on preferences for body characteristics of potential relationship partners in lesbians and heterosexual women. Lesbians (n = 41) rated figure drawings and computer-generated images of women that varied in body fat, waist-to-hip ratio, and breast size; heterosexual women (n = 95) rated computer-generated images of men that varied in muscularity and body fat. Both lesbians and heterosexual women showed a shift in preferences toward more physically attractive partners for shortterm relationships. All body aspects were affected, except that heterosexual women did not show a preference shift for male body fat. The results were interpreted in terms of a mating trade-off strategy in which mate preferences are the consequence of cost/benefit analyses and suggest that preferences for physical attributes of sexual partners may be shared by members of the same sex regardless of sexual orientation.

Left-right facial orientation of familiar faces: developmental aspects of « the mere exposure hypothesis ».

PubMed

Amestoy, Anouck; Bouvard, Manuel P; Cazalets, Jean-René

2010-01-01

We investigated the developmental aspect of sensitivity to the orientation of familiar faces by asking 38 adults and 72 children from 3 to 12 years old to make a preference choice between standard and mirror images of themselves and of familiar faces, presented side-by-side or successively. When familiar (parental) faces were presented simultaneously, 3- to 5-year-olds showed no preference, but by age 5-7 years an adult-like preference for the standard image emerged. Similarly, the adult-like preference for the mirror image of their own face emerged by 5-7 years of age. When familiar or self faces were presented successively, 3- to 7-year-olds showed no preference, and adult-like preference for the standard image emerged by age 7-12 years. These results suggest the occurrence of a developmental process in the perception of familiar face asymmetries which is retained in memory related to knowledge about faces.

Fabrication of high-performance supercapacitors based on transversely oriented carbon nanotubes

NASA Astrophysics Data System (ADS)

Markoulidis, F.; Lei, C.; Lekakou, C.

2013-04-01

High-performance supercapacitors with organic electrolyte 1 M TEABF4 (tetraethyl ammonium tetrafluoroborate) in PC (propylene carbonate) were fabricated and tested, based on multiwall carbon nanotubes (MWNTs) deposited by electrophoresis on three types of alternative substrates: aluminium foil, ITO (indium tin oxide) coated PET (polyethylene terephthalate) film and PET film. In all cases, SEM (scanning electron microscopy) and STEM (scanning transmission electron microscopy) micrographs demonstrated that protruding, transversely oriented MWNT structures were formed, which should increase the transverse conductivity of these MWNT electrodes. The best supercapacitor cell of MWNT electrodes deposited on aluminium foil displayed good transverse orientation of the MWNT structures as well as an in-plane MWNT network at the feet of the protruding structures, which ensured good in-plane conductivity. Capacitor cells with MWNT electrodes deposited either on ITO-coated PET film or on PET film demonstrated lower but still very good performance due to the high density of transversely oriented MWNT structures (good transverse conductivity) but some in-plane inhomogeneities. Capacitor cells with drop-printed MWNTs on aluminium foil, without any transverse orientation, had 16-30 times lower specific capacitance and 5-40 times lower power density than the capacitor cells with the electrophoretically deposited MWNT electrodes.

Astronomical Orientations of Bora Ceremonial Grounds in Southeast Australia

NASA Astrophysics Data System (ADS)

Fuller, Robert S.; Hamacher, Duane W.; Norris, Ray P.

2013-12-01

Ethnographic evidence indicates that bora (initiation) ceremonial sites in southeast Australia, which typically comprise a pair of circles connected by a pathway, are symbolically reflected in the Milky Way as the 'Sky Bora'. This evidence also indicates that the position of the Sky Bora signifies the time of year when initiation ceremonies are held. We use archaeological data to test the hypothesis that southeast Australian bora grounds have a preferred orientation to the position of the Milky Way in the night sky in August, when the plane of the galaxy from Crux to Sagittarius is roughly vertical in the evening sky to the south-southwest. We accomplish this by measuring the orientations of 68 bora grounds using a combination of data from the archaeological literature, and site cards in the New South Wales Aboriginal Heritage Information Management System database. We find that bora grounds have a preferred orientation to the south and southwest, consistent with the Sky Bora hypothesis. Monte Carlo statistics show that these preferences were not the result of chance alignments, but were deliberate.

Substrate Selection for Fundamental Studies of Electrocatalysts and Photoelectrodes: Inert Potential Windows in Acidic, Neutral, and Basic Electrolyte

PubMed Central

Gorlin, Yelena; Jaramillo, Thomas F.

2014-01-01

The selection of an appropriate substrate is an important initial step for many studies of electrochemically active materials. In order to help researchers with the substrate selection process, we employ a consistent experimental methodology to evaluate the electrochemical reactivity and stability of seven potential substrate materials for electrocatalyst and photoelectrode evaluation. Using cyclic voltammetry with a progressively increased scan range, we characterize three transparent conducting oxides (indium tin oxide, fluorine-doped tin oxide, and aluminum-doped zinc oxide) and four opaque conductors (gold, stainless steel 304, glassy carbon, and highly oriented pyrolytic graphite) in three different electrolytes (sulfuric acid, sodium acetate, and sodium hydroxide). We determine the inert potential window for each substrate/electrolyte combination and make recommendations about which materials may be most suitable for application under different experimental conditions. Furthermore, the testing methodology provides a framework for other researchers to evaluate and report the baseline activity of other substrates of interest to the broader community. PMID:25357131

Substrate Selection for Fundamental Studies of Electrocatalysts and Photoelectrodes: Inert Potential Windows in Acidic, Neutral, and Basic Electrolyte

DOE PAGES

Benck, Jesse D.; Pinaud, Blaise A.; Gorlin, Yelena; ...

2014-10-30

The selection of an appropriate substrate is an important initial step for many studies of electrochemically active materials. In order to help researchers with the substrate selection process, we employ a consistent experimental methodology to evaluate the electrochemical reactivity and stability of seven potential substrate materials for electrocatalyst and photoelectrode evaluation. Using cyclic voltammetry with a progressively increased scan range, we characterize three transparent conducting oxides (indium tin oxide, fluorine-doped tin oxide, and aluminum-doped zinc oxide) and four opaque conductors (gold, stainless steel 304, glassy carbon, and highly oriented pyrolytic graphite) in three different electrolytes (sulfuric acid, sodium acetate, andmore » sodium hydroxide). Here, we determine the inert potential window for each substrate/electrolyte combination and make recommendations about which materials may be most suitable for application under different experimental conditions. Furthermore, the testing methodology provides a framework for other researchers to evaluate and report the baseline activity of other substrates of interest to the broader community.« less

Influence of time orientation on food choice: Case study with cookie labels.

PubMed

Tórtora, Giuliana; Ares, Gastón

2018-04-01

Time orientation can influence health-related behaviors, including food consumption. The aim of the present work was to study the influence of time orientation on food choice, using cookie labels as case study. A choice-conjoint task was designed using labels differing in type of cookie (chocolate chips vs. granola), front-of-pack nutrition information (nutritional warnings vs. Facts Up Front system) and nutritional claim (no claim vs. "0% cholesterol. 0% trans fat"). An online study was conducted, in which 155 participants evaluated 8 pairs of cookie labels and selected the one they would buy if they were in the supermarket. Then, they were asked to complete a consideration of future consequences scale (CFC) adapted to eating habits, as well as a questionnaire about socio-demographic characteristics. Time orientation influenced participants' choices of cookies labels; particularly the importance attached to type of cookie. Participants with greater consideration of future consequences preferred the granola cookies, associated with health, while those who prioritized immediate consequences preferred chocolate chip cookies. In addition, nutritional warnings discouraged choice regardless of participants' time orientation. Results from the present work provide additional evidence of the influence of time preferences on food choices and suggest that strategies to stimulate and generate a more future-oriented perspective on eating habits could contribute to more healthful food choices. Copyright © 2018 Elsevier Ltd. All rights reserved.

Time Preferences, Mental Health and Treatment Utilization.

PubMed

Eisenberg, Daniel; Druss, Benjamin G

2015-09-01

In all countries of the world, fewer than half of people with mental disorders receive treatment. This treatment gap is commonly attributed to factors such as consumers' limited knowledge, negative attitudes, and financial constraints. In the context of other health behaviors, such as diet and exercise, behavioral economists have emphasized time preferences and procrastination as additional barriers. These factors might also be relevant to mental health. We examine conceptually and empirically how lack of help-seeking for mental health conditions might be related to time preferences and procrastination. Our conceptual discussion explores how the interrelationships between time preferences and mental health treatment utilization could fit into basic microeconomic theory. The empirical analysis uses survey data of student populations from 12 colleges and universities in 2011 (the Healthy Minds Study, N=8,806). Using standard brief measures of discounting, procrastination, and mental health (depression and anxiety symptoms), we examine the conditional correlations between indicators of present-orientation (discount rate and procrastination) and mental health symptoms. The conceptual discussion reveals a number of potential relationships that would be useful to examine empirically. In the empirical analysis depression is significantly associated with procrastination and discounting. Treatment utilization is significantly associated with procrastination but not discounting. The empirical results are generally consistent with the idea that depression increases present orientation (reduces future orientation), as measured by discounting and procrastination. These analyses have notable limitations that will require further examination in future research: the measures are simple and brief, and the estimates may be biased from true causal effects because of omitted variables and reverse causality. There are several possibilities for future research, including: (i) observational, longitudinal studies with detailed data on mental health, time preferences, and help-seeking; (ii) experimental studies that examine immediate or short-term responses and connections between these variables; (iii) randomized trials of mental health therapies that include outcome measures of time preferences and procrastination; and, (iv) intervention studies that test strategies to influence help-seeking by addressing time preferences and present orientation.

Coarse-Scale Biases for Spirals and Orientation in Human Visual Cortex

PubMed Central

Heeger, David J.

2013-01-01

Multivariate decoding analyses are widely applied to functional magnetic resonance imaging (fMRI) data, but there is controversy over their interpretation. Orientation decoding in primary visual cortex (V1) reflects coarse-scale biases, including an over-representation of radial orientations. But fMRI responses to clockwise and counter-clockwise spirals can also be decoded. Because these stimuli are matched for radial orientation, while differing in local orientation, it has been argued that fine-scale columnar selectivity for orientation contributes to orientation decoding. We measured fMRI responses in human V1 to both oriented gratings and spirals. Responses to oriented gratings exhibited a complex topography, including a radial bias that was most pronounced in the peripheral representation, and a near-vertical bias that was most pronounced near the foveal representation. Responses to clockwise and counter-clockwise spirals also exhibited coarse-scale organization, at the scale of entire visual quadrants. The preference of each voxel for clockwise or counter-clockwise spirals was predicted from the preferences of that voxel for orientation and spatial position (i.e., within the retinotopic map). Our results demonstrate a bias for local stimulus orientation that has a coarse spatial scale, is robust across stimulus classes (spirals and gratings), and suffices to explain decoding from fMRI responses in V1. PMID:24336733

The orientation of the mineral crystals in the radius and tibia of the sheep, and its variation with age.

PubMed Central

Bacon, G E; Goodship, A E

1991-01-01

The direction of preferred orientation of the hydroxyapatite crystals in both the tibia and radius of the sheep is close to the long axis of the bone, notwithstanding the angle of about 30 degrees which, for the tibia, exists between the long axis and the direction of principal dynamic strain during locomotion. For both bones the orientation of the cranial cortex, which is a tension surface during locomotion, is about 40% larger than the caudal. The variation with age of the magnitude of the preferred orientation for the sheep bones is contrasted with what has been reported earlier for the human femur. Notably, for the sheep, both bones show substantial orientation at birth--having increased steadily during gestation--so that the animal is able to stand and walk at the outset. PMID:1817133

Can infants' orientation to social stimuli predict later joint attention skills?

PubMed

Schietecatte, Inge; Roeyers, Herbert; Warreyn, Petra

2012-06-01

From the moment infants are born, they seem to prefer orienting to social stimuli, over objects and non-social stimuli. This preference lasts throughout adulthood and is believed to play a crucial role in social-communicative development. By following up a group of infants at the age of 6, 8, and 12 months, this study explored the role of social orienting in the early development of joint attention skills. The expected association between social orienting and joint attention was partially confirmed. Social orienting in real-life photographs of everyday situations was not related to later joint attention skills, however fixation to the eyes in a neutral face was related to response to joint attention skills, and fixation to the eyes in a dynamic video clip of a talking person was predictive of initiating joint attention skills. Several alternative interpretations of the results are discussed. ©2011 The British Psychological Society.

The basis of orientation decoding in human primary visual cortex: fine- or coarse-scale biases?

PubMed

Maloney, Ryan T

2015-01-01

Orientation signals in human primary visual cortex (V1) can be reliably decoded from the multivariate pattern of activity as measured with functional magnetic resonance imaging (fMRI). The precise underlying source of these decoded signals (whether by orientation biases at a fine or coarse scale in cortex) remains a matter of some controversy, however. Freeman and colleagues (J Neurosci 33: 19695-19703, 2013) recently showed that the accuracy of decoding of spiral patterns in V1 can be predicted by a voxel's preferred spatial position (the population receptive field) and its coarse orientation preference, suggesting that coarse-scale biases are sufficient for orientation decoding. Whether they are also necessary for decoding remains an open question, and one with implications for the broader interpretation of multivariate decoding results in fMRI studies. Copyright © 2015 the American Physiological Society.

10 CFR Appendix C to Part 20 - Quantities 1 of Licensed Material Requiring Labeling

Code of Federal Regulations, 2012 CFR

2012-01-01

... Indium-115 100 Indium-116m 1,000 Indium-117m 1,000 Indium-117 1,000 Indium-119m 1,000 Tin-110 100 Tin-111 1,000 Tin-113 100 Tin-117m 100 Tin-119m 100 Tin-121m 100 Tin-121 1,000 Tin-123m 1,000 Tin-123 10 Tin-125 10 Tin-126 10 Tin-127 1,000 Tin-128 1,000 Antimony-115 1,000 Antimony-116m 1,000 Antimony-116 1...

An experimental approach in revisiting the magnetic orientation of cattle.

PubMed

Weijers, Debby; Hemerik, Lia; Heitkönig, Ignas M A

2018-01-01

In response to the increasing number of observational studies on an apparent south-north orientation in non-homing, non-migrating terrestrial mammals, we experimentally tested the alignment hypothesis using strong neodymium magnets on the resting orientation of individual cattle in Portugal. Contrary to the hypothesis, the 34 cows in the experiment showed no directional preference, neither with, nor without a strong neodymium magnet fixed to their collar. The concurrently performed 2,428 daytime observations-excluding the hottest part of the day-of 659 resting individual cattle did not show a south-north alignment when at rest either. The preferred compass orientation of these cows was on average 130 degrees from the magnetic north (i.e., south east). Cow compass orientation correlated significantly with sun direction, but not with wind direction. In as far as we can determine, this is the first experimental test on magnetic orientation in larger, non-homing, non-migrating mammals. These experimental and observational findings do not support previously published suggestions on the magnetic south-north alignment in these mammals.

Surgery clerkship orientation: evaluating temporal changes in student orientation needs.

PubMed

O'Neill, Conor; Moore, Jesse; Callas, Peter

2016-08-01

Surgery clerkship students at our institution receive a standardized orientation covering objectives, requirements, grading, and expectations. Limited data exist regarding the student perceptions of this approach. Surveys were provided to students to rate the importance of orientation topics and their satisfaction with topic conclusion. Scores between student groupings over the clerkship year were analyzed with Student t tests and analysis of variance with Scheffe adjustments. Significant differences in the mean importance rating between topics exists (P < .0001) as well as among satisfaction scores for topics (P < .0005). Early clerkship students value course expectations higher than later students (P = .03). Early clerkship students want more time devoted to hospital tours and expectations compared with later students (31% vs 8%). Orientation needs for students change over the clerkship year. Beginning students prefer basic direction for time spent on the ward. Later students prefer information regarding shelf preparation. Surgery course directors can adapt the orientation based on the experience of clerkship students. Copyright © 2016 Elsevier Inc. All rights reserved.

Young doctors' preferences for payment systems: the influence of gender and personality traits.

PubMed

Abelsen, Birgit; Olsen, Jan Abel

2015-08-19

Activity-based payment contracts are common among doctors, but to what extent are they preferred? The aim of this paper is to elicit young doctors' preferences for alternative payment systems before they have adapted to an existing system. We examine the existence of gender differences and the extent to which personality traits determine preferences. A cross-sectional survey of all final-year medical students and all interns in Norway examined the extent to which preferences for different payment systems depend on gender and personality traits. Data analysis relied on one-way ANOVA and multinomial logistic regression. The current activity-based payment systems were the least preferred, both in hospitals (16.6%) and in general practice (19.7%). The contrasting alternative "fixed salary" achieved similar relative support. Approximately half preferred the hybrid alternative. When certainty associated with a payment system increased, its appeal rose for women and individuals who are less prestige-oriented, risk-tolerant or effort-tolerant. Activity-based systems were preferred among status- and income-oriented respondents. The vast majority of young doctors prefer payment systems that are less activity-based than the current contracts offered in the Norwegian health service. Recruitment and retention in less prestigious medical specialities might improve if young doctors could choose payment systems corresponding with their diverse preferences.

Bivariate and Multivariate Associations between Trait Listening Goals and Trait Communicator Preferences

ERIC Educational Resources Information Center

Keaton, Shaughan A.; Keteyian, Robert V.; Bodie, Graham D.

2014-01-01

This article provides validity evidence for a measure of listening goals by showing theoretically consistent relationships with an existing communication preference questionnaire. Participants (N = 257) were administered trait measures for listening goals and communicator preferences. The four listening goals--relational, task-oriented,…

Senior High School Students' Preference and Reasoning Modes about Nuclear Energy Use.

ERIC Educational Resources Information Center

Yang, Fang-Ying; Anderson, O. Roger

2003-01-01

Examines senior high school students' cognitive orientation toward scientific or social information, designated as information preference, and associated preferential reasoning modes when presented with an environmental issue concerning nuclear energy usage. Investigates the association of information preference variable with academic and personal…

Correlated Preferences for Male Facial Masculinity and Partner Traits in Gay and Bisexual Men in China.

PubMed

Zheng, Lijun; Zheng, Yong

2015-07-01

Previous studies have documented the correlation between preferences for male facial masculinity and perceived masculinity: women who rate their male partner as more masculine tend to prefer more masculine faces. Men's self-rated masculinity predicts their female partner's preference for masculinity. This study examined the association between other trait preferences and preference for male facial masculinity among 556 gay and bisexual men across multiple cities in China. Participants were asked to choose the three most important traits in a romantic partner from a list of 23 traits. Each participant was then asked to choose a preferred face in each of 10 pairs of male faces presented sequentially, with each pair consisting of a masculinized and feminized version of the same base face. The results indicated that preferences for health and status-related traits were correlated with preferences for male facial masculinity in gay and bisexual men in China; individuals who were more health- or status-oriented in their preferences for a romantic partner preferred more masculine male faces than individuals with lower levels of these orientations. The findings have implications for the correlated preferences for facial masculinity and health- and status-related traits and may be related to perceived health and dominance/aggression of masculine faces based on a sample of non-Western gay and bisexual men.

Esthetic smile preferences and the orientation of the maxillary occlusal plane.

PubMed

Kattadiyil, Mathew T; Goodacre, Charles J; Naylor, W Patrick; Maveli, Thomas C

2012-12-01

The anteroposterior orientation of the maxillary occlusal plane has an important role in the creation, assessment, and perception of an esthetic smile. However, the effect of the angle at which this plane is visualized (the viewing angle) in a broad smile has not been quantified. The purpose of this study was to assess the esthetic preferences of dental professionals and nondentists by using 3 viewing angles of the anteroposterior orientation of the maxillary occlusal plane. After Institutional Review Board approval, standardized digital photographic images of the smiles of 100 participants were recorded by simultaneously triggering 3 cameras set at different viewing angles. The top camera was positioned 10 degrees above the occlusal plane (camera #1, Top view); the center camera was positioned at the level of the occlusal plane (camera #2, Center view); and the bottom camera was located 10 degrees below the occlusal plane (camera #3, Bottom view). Forty-two dental professionals and 31 nondentists (persons from the general population) independently evaluated digital images of each participant's smile captured from the Top view, Center view, and Bottom view. The 73 evaluators were asked individually through a questionnaire to rank the 3 photographic images of each patient as 'most pleasing,' 'somewhat pleasing,' or 'least pleasing,' with most pleasing being the most esthetic view and the preferred orientation of the occlusal plane. The resulting esthetic preferences were statistically analyzed by using the Friedman test. In addition, the participants were asked to rank their own images from the 3 viewing angles as 'most pleasing,' 'somewhat pleasing,' and 'least pleasing.' The 73 evaluators found statistically significant differences in the esthetic preferences between the Top and Bottom views and between the Center and Bottom views (P<.001). No significant differences were found between the Top and Center views. The Top position was marginally preferred over the Center, and both were significantly preferred over the Bottom position. When the participants evaluated their own smiles, a significantly greater number (P< .001) preferred the Top view over the Center or the Bottom views. No significant differences were found in preferences based on the demographics of the evaluators when comparing age, education, gender, profession, and race. The esthetic preference for the maxillary occlusal plane was influenced by the viewing angle with the higher (Top) and center views preferred by both dental and nondental evaluators. The participants themselves preferred the higher view of their smile significantly more often than the center or lower angle views (P<.001). Copyright © 2012 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Universality in the Evolution of Orientation Columns in the Visual Cortex

PubMed Central

Kaschube, Matthias; Schnabel, Michael; Löwel, Siegrid; Coppola, David M.; White, Leonard E.; Wolf, Fred

2011-01-01

The brain’s visual cortex processes information concerning form, pattern, and motion within functional maps that reflect the layout of neuronal circuits. We analyzed functional maps of orientation preference in the ferret, tree shrew, and galago—three species separated since the basal radiation of placental mammals more than 65 million years ago—and found a common organizing principle. A symmetry-based class of models for the self-organization of cortical networks predicts all essential features of the layout of these neuronal circuits, but only if suppressive long-range interactions dominate development. We show mathematically that orientation-selective long-range connectivity can mediate the required interactions. Our results suggest that self-organization has canalized the evolution of the neuronal circuitry underlying orientation preference maps into a single common design. PMID:21051599

A Gaze-Driven Evolutionary Algorithm to Study Aesthetic Evaluation of Visual Symmetry

PubMed Central

Bertamini, Marco; Jones, Andrew; Holmes, Tim; Zanker, Johannes M.

2016-01-01

Empirical work has shown that people like visual symmetry. We used a gaze-driven evolutionary algorithm technique to answer three questions about symmetry preference. First, do people automatically evaluate symmetry without explicit instruction? Second, is perfect symmetry the best stimulus, or do people prefer a degree of imperfection? Third, does initial preference for symmetry diminish after familiarity sets in? Stimuli were generated as phenotypes from an algorithmic genotype, with genes for symmetry (coded as deviation from a symmetrical template, deviation–symmetry, DS gene) and orientation (0° to 90°, orientation, ORI gene). An eye tracker identified phenotypes that were good at attracting and retaining the gaze of the observer. Resulting fitness scores determined the genotypes that passed to the next generation. We recorded changes to the distribution of DS and ORI genes over 20 generations. When participants looked for symmetry, there was an increase in high-symmetry genes. When participants looked for the patterns they preferred, there was a smaller increase in symmetry, indicating that people tolerated some imperfection. Conversely, there was no increase in symmetry during free viewing, and no effect of familiarity or orientation. This work demonstrates the viability of the evolutionary algorithm approach as a quantitative measure of aesthetic preference. PMID:27433324

Early Hormonal Influences on Childhood Sex-Typed Activity and Playmate Preferences: Implications for the Development of Sexual Orientation.

ERIC Educational Resources Information Center

Berenbaum, Sheri A.; Snyder, Elizabeth

1995-01-01

Examined hormonal influences on activity and playmate preferences in children with congenital adrenal hyperplasia (CAH) age 2.5 to 12 years and their relatives. Found that girls with CAH preferred boys' toys and activities, whereas boys with CAH did not differ significantly from controls. Activity and playmate preferences were not related. (MDM)

Neurons in cat V1 show significant clustering by degree of tuning

PubMed Central

Ziskind, Avi J.; Emondi, Al A.; Kurgansky, Andrei V.; Rebrik, Sergei P.

2015-01-01

Neighboring neurons in cat primary visual cortex (V1) have similar preferred orientation, direction, and spatial frequency. How diverse is their degree of tuning for these properties? To address this, we used single-tetrode recordings to simultaneously isolate multiple cells at single recording sites and record their responses to flashed and drifting gratings of multiple orientations, spatial frequencies, and, for drifting gratings, directions. Orientation tuning width, spatial frequency tuning width, and direction selectivity index (DSI) all showed significant clustering: pairs of neurons recorded at a single site were significantly more similar in each of these properties than pairs of neurons from different recording sites. The strength of the clustering was generally modest. The percent decrease in the median difference between pairs from the same site, relative to pairs from different sites, was as follows: for different measures of orientation tuning width, 29–35% (drifting gratings) or 15–25% (flashed gratings); for DSI, 24%; and for spatial frequency tuning width measured in octaves, 8% (drifting gratings). The clusterings of all of these measures were much weaker than for preferred orientation (68% decrease) but comparable to that seen for preferred spatial frequency in response to drifting gratings (26%). For the above properties, little difference in clustering was seen between simple and complex cells. In studies of spatial frequency tuning to flashed gratings, strong clustering was seen among simple-cell pairs for tuning width (70% decrease) and preferred frequency (71% decrease), whereas no clustering was seen for simple-complex or complex-complex cell pairs. PMID:25652921

The impact of orientation filtering on face-selective neurons in monkey inferior temporal cortex.

PubMed

Taubert, Jessica; Goffaux, Valerie; Van Belle, Goedele; Vanduffel, Wim; Vogels, Rufin

2016-02-16

Faces convey complex social signals to primates. These signals are tolerant of some image transformations (e.g. changes in size) but not others (e.g. picture-plane rotation). By filtering face stimuli for orientation content, studies of human behavior and brain responses have shown that face processing is tuned to selective orientation ranges. In the present study, for the first time, we recorded the responses of face-selective neurons in monkey inferior temporal (IT) cortex to intact and scrambled faces that were filtered to selectively preserve horizontal or vertical information. Guided by functional maps, we recorded neurons in the lateral middle patch (ML), the lateral anterior patch (AL), and an additional region located outside of the functionally defined face-patches (CONTROL). We found that neurons in ML preferred horizontal-passed faces over their vertical-passed counterparts. Neurons in AL, however, had a preference for vertical-passed faces, while neurons in CONTROL had no systematic preference. Importantly, orientation filtering did not modulate the firing rate of neurons to phase-scrambled face stimuli in any recording region. Together these results suggest that face-selective neurons found in the face-selective patches are differentially tuned to orientation content, with horizontal tuning in area ML and vertical tuning in area AL.

Parallel tempering Monte Carlo simulations of lysozyme orientation on charged surfaces

NASA Astrophysics Data System (ADS)

Xie, Yun; Zhou, Jian; Jiang, Shaoyi

2010-02-01

In this work, the parallel tempering Monte Carlo (PTMC) algorithm is applied to accurately and efficiently identify the global-minimum-energy orientation of a protein adsorbed on a surface in a single simulation. When applying the PTMC method to simulate lysozyme orientation on charged surfaces, it is found that lysozyme could easily be adsorbed on negatively charged surfaces with "side-on" and "back-on" orientations. When driven by dominant electrostatic interactions, lysozyme tends to be adsorbed on negatively charged surfaces with the side-on orientation for which the active site of lysozyme faces sideways. The side-on orientation agrees well with the experimental results where the adsorbed orientation of lysozyme is determined by electrostatic interactions. As the contribution from van der Waals interactions gradually dominates, the back-on orientation becomes the preferred one. For this orientation, the active site of lysozyme faces outward, which conforms to the experimental results where the orientation of adsorbed lysozyme is co-determined by electrostatic interactions and van der Waals interactions. It is also found that despite of its net positive charge, lysozyme could be adsorbed on positively charged surfaces with both "end-on" and back-on orientations owing to the nonuniform charge distribution over lysozyme surface and the screening effect from ions in solution. The PTMC simulation method provides a way to determine the preferred orientation of proteins on surfaces for biosensor and biomaterial applications.

The Meaning of Being Predominantly Present-Oriented in Middle Age and in Non-Western Context.

ERIC Educational Resources Information Center

Shirai, Toshiaki

This paper describes a study of time orientation and preferences of people in western and nonwestern cultures at various life stages. Data were gathered by means of a literature review and a time orientation questionnaire completed by 1,657 individuals in Belgium and Japan. Findings of the study suggest that the time orientation that enhances…

Temperature controlled properties of sub-micron thin SnS films

NASA Astrophysics Data System (ADS)

Nwankwo, Stephen N.; Campbell, Stephen; Reddy, Ramakrishna K. T.; Beattie, Neil S.; Barrioz, Vincent; Zoppi, Guillaume

2018-06-01

Tin sulphide (SnS) thin films deposited by thermal evaporation on glass substrates are studied for different substrate temperatures. The increase in substrate temperature results in the increase of the crystallite size and change in orientation of the films. The crystal structure of the films is that of SnS only and for temperatures ≤300 °C the films are of random orientation, whereas for higher temperatures the films become (040) oriented. The variation of Sn/S composition was accompanied by a reduction in optical energy bandgap from 1.47 to 1.31 eV as the substrate temperature increases. The Urbach energy was found stable at 0.169 ± 0.002 eV for temperature up to 350 °C. Photoluminescence emission was observed only for films exhibiting stoichiometric properties and shows that a precise control of the film composition is critical to fabricate devices while an increase in grain size will be essential to achieve high efficiency.

Poly (p-phenyleneneacetylene) light-emitting diodes

DOEpatents

Shinar, Joseph; Swanson, Leland S.; Lu, Feng; Ding, Yiwei; Barton, Thomas J.; Vardeny, Zeev V.

1994-10-04

Acetylene containing poly(p-phenyleneacetylene) (PPA) - based light-emitting diodes (LEDs) are provided. The LEDs are fabricated by coating a hole-injecting electrode, preferably an indium tin oxide (ITO) coated glass substrate, with a PPA polymer, such as a 2,5-dibutoxy or a 2,5-dihexoxy derivative of PPA, dissolved in an organic solvent. This is then followed by evaporating a layer of material capable of injecting electrons, such as Al or Al/Ca, onto the polymer to form a base electrode. This composition is then annealed to form efficient EL diodes.

Poly (p-phenyleneacetylene) light-emitting diodes

DOEpatents

Shinar, J.; Swanson, L.S.; Lu, F.; Ding, Y.; Barton, T.J.; Vardeny, Z.V.

1994-10-04

Acetylene containing poly(p-phenyleneacetylene) (PPA) - based light-emitting diodes (LEDs) are provided. The LEDs are fabricated by coating a hole-injecting electrode, preferably an indium tin oxide (ITO) coated glass substrate, with a PPA polymer, such as a 2,5-dibutoxy or a 2,5-dihexoxy derivative of PPA, dissolved in an organic solvent. This is then followed by evaporating a layer of material capable of injecting electrons, such as Al or Al/Ca, onto the polymer to form a base electrode. This composition is then annealed to form efficient EL diodes. 8 figs.

Fabrication of poly(p-phenyleneacetylene) light-emitting diodes

DOEpatents

Shinar, J.; Swanson, L.S.; Lu, F.; Ding, Y.

1994-08-02

Acetylene-containing poly(p-phenyleneacetylene) (PPA)-based light-emitting diodes (LEDs) are provided. The LEDs are fabricated by coating a hole-injecting electrode, preferably an indium tin oxide (ITO) coated glass substrate, with a PPA polymer, such as a 2,5-dibutoxy or a 2,5-dihexoxy derivative of PPA, dissolved in an organic solvent. This is then followed by evaporating a layer of material capable of injecting electrons, such as Al or Al/Ca, onto the polymer to form a base electrode. This composition is then annealed to form efficient EL diodes. 8 figs.

Fabrication of poly(p-phenyleneacetylene) light-emitting diodes

DOEpatents

Shinar, Joseph; Swanson, Leland S.; Lu, Feng; Ding, Yiwei

1994-08-02

Acetylene containing poly(p-phenyleneacetylene) (PPA) - based light-emitting diodes (LEDs) are provided. The LEDs are fabricated by coating a hole-injecting electrode, preferably an indium tin oxide (ITO) coated glass substrate, with a PPA polymer, such as a 2,5-dibutoxy or a 2,5-dihexoxy derivative of PPA, dissolved in an organic solvent. This is then followed by evaporating a layer of material capable of injecting electrons, such as A1 or A1/Ca, onto the polymer to form a base electrode. This composition is then annealed to form efficient EL diodes.

Career plans for male-dominated occupations among female seniors in religious and secular high schools.

PubMed

Rich, Y; Golan, R

1992-01-01

This study investigated the hypothesis that the religious beliefs of young women significantly affect their career planning. All female seniors (N = 315) in one public religious and two public secular high schools in Israel responded to inventories examining their (1) orientation to homemaking or career, (2) interest in male-dominated occupations, and (3) preference for male-dominated occupations. Results from regression analyses indicated that young women from the secular schools, as compared to those from the religious school, expressed greater interest in and preference for male-dominated occupations. In addition, religious orientation, more than other background variables, had predictive power for interest in and preference for male-dominated occupations.

METALLURGY OF ZIRCALOY-2. PART II. THE EFFECTS OF FABRICATION VARIABLES ON THE PREFERRED ORIENTATION AND ANISOTROPY OF STRAIN BEHAVIOR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rittenhouse, P.L.; Picklesimer, M.L.

1961-02-01

The preferred orientation and anisotropy of strain behavior of Zircaloy- 2 were studied as functions of fabrication variables. An inverse-pole-figure technique was used for the preferred orientation determinations. Evaluation of the effects of the fabrication variables on the anisotropy of strain behavior was accomplished by a contractile strainaxial strain analysis. An analysis of strain behavior in the normal direction was developed on the basis of theory of plastic flow of anisotropic metals. A simple intuitively derivable relation was found to exist between the strainstrain analysis and the preferred orientation data. Correlations of the strain-strain data with true-stress-truestrain diagrams and mechanicalmore » properties were attempted. The preferred orientation of Zircaloy-2 produced by the Oak Ridge National Laboratory-Homogeneous Reactor Project (ORNL- HRP) metallurgy fabrication schedule (ingot breakdown at 1500 to 1900 deg F, major reduction at 1800 to 1900 deg F or 1350 to 1450 deg F, a heat treatment of 30 min at 1800 at 1550 deg F followed by a water quench or rapid air cool to below 1200 deg F, a final reduction of 25 to 40% at 1000 deg F. and a 3O-min anneal at 1400 to 1425 deg F) was weak compared to that of most of the other schedules investigated. Elimination of the beta heat treatment (1800 to 1850 deg F for 30 min) between the major reduction and final reduction steps resulted in a material with a high degree of preferred orienation and with a state of pseudoisotropy in ihe rolling plane. A unique and quite high degree of preferred orientaion was developed when the ORNL-HRP metallurgy fabrication procedure was used, but the ingot axis was in the transverse rather than the rolling direction of the finished plate permitting more contractile sirain to occur in the normal direction than in either the rolling or transverse directions. The strain-strain analyses of the materials were consistent with the conclusions reached by the preferred orientation analyses. The effects of cross rolling on the anisotropy of strain behavior of Zircaloy-2 were found to depend on the type of cross rolling (unidirectional or rotational), the temperature of cross rolling, and the stage of fabrication at which the cross rolling was done. Unidirectional cross rolling at 1000 deg F after beta heat treatment caused only a slight increase in anisotropy of strain behavior over that for straight-rolled material, but roiational cross rolling at 1000 deg F after beta heat treatment resulted in a material with a state of isotropy of strain behavior only in the rolling plane. Rotational cross rolling before beta heat treatment, for one material at 1450 deg F and for another from 1900 deg F, produced different states or degrees of anisotropy of strain behavior. Because of flow constraints which exist in sheettype tensile specimens with width-to-thickness ratios > 1.0, it is imperative that round tensile specimens be used in the contractile strain-axial strain analysis. Since the principal axes of anisotropy are generally not the major sheet directions, they must be found by the preferred orientation analysis. (auth)« less

Homosexual mating preferences from an evolutionary perspective: sexual selection theory revisited.

PubMed

Gobrogge, Kyle L; Perkins, Patrick S; Baker, Jessica H; Balcer, Kristen D; Breedlove, S Marc; Klump, Kelly L

2007-10-01

Studies in evolutionary psychology and sexual selection theory show that heterosexual men prefer younger mating partners than heterosexual women in order to ensure reproductive success. However, previous research has generally not examined differences in mating preferences as a function of sexual orientation or the type of relationship sought in naturalistic settings. Given that homosexual men seek partners for reasons other than procreation, they may exhibit different mating preferences than their heterosexual counterparts. Moreover, mating preferences may show important differences depending on whether an individual is seeking a long-term versus a short-term relationship. The purpose of the present study was to examine these issues by comparing partner preferences in terms of age and relationship type between homosexual and heterosexual men placing internet personal advertisements. Participants included 439 homosexual and 365 heterosexual men who placed internet ads in the U.S. or Canada. Ads were coded for the participant's age, relationship type (longer-term or short-term sexual encounter) sought, and partner age preferences. Significantly more homosexual than heterosexual men sought sexual encounters, although men (regardless of sexual orientation) seeking sexual encounters preferred a significantly wider age range of partners than men seeking longer-term relationships. These findings suggest that partner preferences are independent of evolutionary drives to procreate, since both types of men preferred similar ages in their partners. In addition, they highlight the importance of examining relationship type in evolutionary studies of mating preferences, as men's partner preferences show important differences depending upon the type of relationship sought.

Fishing for Northern Pike in Minnesota: A comparison of anglers and dark house spearers

USGS Publications Warehouse

Schroeder, Susan A.; Fulton, David C.

2014-01-01

In order to project fishing effort and demand of individuals targeting Northern Pike Esox lucius in Minnesota, it is important to understand the catch orientations, management preferences, and site choice preferences of those individuals. Northern Pike are specifically targeted by about 35% of the approximately 1.5 million licensed anglers in Minnesota and by approximately 14,000–15,000 dark house spearers. Dark house spearing is a traditional method of harvesting fish through the ice in winter. Mail surveys were distributed to three research strata: anglers targeting Northern Pike, dark house spearing license holders spearing Northern Pike, and dark house spearing license holders angling for Northern Pike. Dark house spearers, whether spearing or angling, reported a stronger orientation toward keeping Northern Pike than did anglers. Anglers reported a stronger orientation toward catching large Northern Pike than did dark house spearers when spearing or angling. Northern Pike regulations were the most important attribute affecting site choice for respondents in all three strata. Models for all strata indicated a preference for lakes without protected slot limits. However, protected slot limits had a stronger negative influence on lake preference for dark house spearing licensees (whether spearing or angling) than for anglers.

Coupling mesodomain positional ordering to intra-domain orientational ordering in block copolymer assembly

NASA Astrophysics Data System (ADS)

Burke, Christopher; Reddy, Abhiram; Prasad, Ishan; Grason, Gregory

Block copolymer (BCP) melts form a number of symmetric microphases, e.g. columnar or double gyroid phases. BCPs with a block composed of chiral monomers are observed to form bulk phases with broken chiral symmetry e.g. a phase of hexagonally ordered helical mesodomains. Other new structures may be possible, e.g. double gyroid with preferred chirality which has potential photonic applications. One approach to understanding chirality transfer from monomer to the bulk is to use self consistent field theory (SCFT) and incorporate an orientational order parameter with a preference for handed twist in chiral block segments, much like the texture of cholesteric liquid crystal. Polymer chains in achiral BCPs exhibit orientational ordering which couples to the microphase geometry; a spontaneous preference for ordering may have an effect on the geometry. The influence of a preference for chiral polar (vectorial) segment order has been studied to some extent, though the influence of coupling to chiral tensorial (nematic) order has not yet been developed. We present a computational approach using SCFT with vector and tensor order which employs well developed pseudo-spectral methods. Using this we explore how tensor order influences which structures form, and if it can promote chiral phases.

Crystallographic orientation of the c-axis of biological apatite as a new index of the quality of subchondral bone in knee joint osteoarthritis.

PubMed

Lee, Jee-Wook; Kobayashi, Akio; Nakano, Takayoshi

2017-05-01

The aim of the present study was to investigate the preferred orientation of biological apatite (BAp) as a new index of the quality of subchondral bone (SB) in knee joint osteoarthritis (OA). Ten OA and five normal knee joints were obtained. Thickness, quantity and bone mineral density (BMD) of SB were analyzed at the medial condyle of the femur in dry conditions by peripheral quantitative computed tomography. In addition, the preferred crystallographic orientation of the c-axis of BAp was evaluated as bone quality parameter using a microbeam X-ray diffractometer technique. BMD and thickness of SB were significantly increased in OA specimens compared to normal knee specimens (P < 0.01), and the preferred orientation of the c-axis of BAp along the normal direction of SB surface was significantly higher in OA specimens (P < 0.01), reflecting the change in stress of concentration in the pathological portion without cartilage. SB sclerosis in OA results in both proliferation of bone tissues and enhanced degree of preferential alignment of the c-axis of BAp. Our findings could have major implications for the diagnosis of clinical studies, including pathologic elucidation in OA.

The C-Terminal Extension Unique to the Long Isoform of the Shelterin Component TIN2 Enhances Its Interaction with TRF2 in a Phosphorylation- and Dyskeratosis Congenita Cluster-Dependent Fashion.

PubMed

Nelson, Nya D; Dodson, Lois M; Escudero, Laura; Sukumar, Ann T; Williams, Christopher L; Mihalek, Ivana; Baldan, Alessandro; Baird, Duncan M; Bertuch, Alison A

2018-06-15

TIN2 is central to the shelterin complex, linking the telomeric proteins TRF1 and TRF2 with TPP1/POT1. Mutations in TINF2 , which encodes TIN2, that are found in dyskeratosis congenita (DC) result in very short telomeres and cluster in a region shared by the two TIN2 isoforms, TIN2S (short) and TIN2L (long). Here we show that TIN2L, but not TIN2S, is phosphorylated. TRF2 interacts more with TIN2L than TIN2S, and both the DC cluster and phosphorylation promote this enhanced interaction. The binding of TIN2L, but not TIN2S, is affected by TRF2-F120, which is also required for TRF2's interaction with end processing factors such as Apollo. Conversely, TRF1 interacts more with TIN2S than with TIN2L. A DC-associated mutation further reduces TIN2L-TRF1, but not TIN2S-TRF1, interaction. Cells overexpressing TIN2L or phosphomimetic TIN2L are permissive to telomere elongation, whereas cells overexpressing TIN2S or phosphodead TIN2L are not. Telomere lengths are unchanged in cell lines in which TIN2L expression has been eliminated by clustered regularly interspaced short palindromic repeat (CRISPR)/Cas9-mediated mutation. These results indicate that TIN2 isoforms are biochemically and functionally distinguishable and that shelterin composition could be fundamentally altered in patients with TINF2 mutations. Copyright © 2018 Nelson et al.

Preferred growth orientation and microsegregation behaviors of eutectic in a nickel-based single-crystal superalloy

PubMed Central

Ma, Dexin; Bührig-Polaczek, Andreas

2015-01-01

A nickel-based single-crystal superalloy was employed to investigate the preferred growth orientation behavior of the (γ + γ′) eutectic and the effect of these orientations on the segregation behavior. A novel solidification model for the eutectic island was proposed. At the beginning of the eutectic island’s crystallization, the core directly formed from the liquid by the eutectic reaction, and then preferably grew along [100] direction. The crystallization of the eutectic along [110] always lagged behind that in [100] direction. The eutectic growth in [100] direction terminated on impinging the edge of the dendrites or another eutectic island. The end of the eutectic island’s solidification terminates due to the encroachment of the eutectic liquid/solid interface at the dendrites or another eutectic island in [110] direction. The distribution of the alloying elements depended on the crystalline axis. The degree of the alloying elements’ segregation was lower along [100] than [110] direction with increasing distance from the eutectic island’s center. PMID:27877773

Revealing the preferred interlayer orientations and stackings of two-dimensional bilayer gallium selenide crystals.

PubMed

Li, Xufan; Basile, Leonardo; Yoon, Mina; Ma, Cheng; Puretzky, Alexander A; Lee, Jaekwang; Idrobo, Juan C; Chi, Miaofang; Rouleau, Christopher M; Geohegan, David B; Xiao, Kai

2015-02-23

Characterizing and controlling the interlayer orientations and stacking orders of two-dimensional (2D) bilayer crystals and van der Waals (vdW) heterostructures is crucial to optimize their electrical and optoelectronic properties. The four polymorphs of layered gallium selenide (GaSe) crystals that result from different layer stackings provide an ideal platform to study the stacking configurations in 2D bilayer crystals. Through a controllable vapor-phase deposition method, bilayer GaSe crystals were selectively grown and their two preferred 0° or 60° interlayer rotations were investigated. The commensurate stacking configurations (AA' and AB stacking) in as-grown bilayer GaSe crystals are clearly observed at the atomic scale, and the Ga-terminated edge structure was identified using scanning transmission electron microscopy. Theoretical analysis reveals that the energies of the interlayer coupling are responsible for the preferred orientations among the bilayer GaSe crystals. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Theoretical Orientation and Personality of the Therapist: A Graduate Student Sample

ERIC Educational Resources Information Center

Ivanovic, Mirka

2011-01-01

The current study adds to the literature--and addresses several identified limitations--about the relationship between therapist trainees' personality traits and their preference for a particular theoretical orientation(s). Therapist trainees (N = 197) in a Clinical Psy.D program at The Chicago School of Professional Psychology completed a paper…

Accessibility versus Accuracy in Retrieving Spatial Memory: Evidence for Suboptimal Assumed Headings

ERIC Educational Resources Information Center

Yerramsetti, Ashok; Marchette, Steven A.; Shelton, Amy L.

2013-01-01

Orientation dependence in spatial memory has often been interpreted in terms of accessibility: Object locations are encoded relative to a reference orientation that affords the most accurate access to spatial memory. An open question, however, is whether people naturally use this "preferred" orientation whenever recalling the space. We…

An experimental approach in revisiting the magnetic orientation of cattle

PubMed Central

Weijers, Debby; Hemerik, Lia; Heitkönig, Ignas M. A.

2018-01-01

In response to the increasing number of observational studies on an apparent south-north orientation in non-homing, non-migrating terrestrial mammals, we experimentally tested the alignment hypothesis using strong neodymium magnets on the resting orientation of individual cattle in Portugal. Contrary to the hypothesis, the 34 cows in the experiment showed no directional preference, neither with, nor without a strong neodymium magnet fixed to their collar. The concurrently performed 2,428 daytime observations—excluding the hottest part of the day—of 659 resting individual cattle did not show a south-north alignment when at rest either. The preferred compass orientation of these cows was on average 130 degrees from the magnetic north (i.e., south east). Cow compass orientation correlated significantly with sun direction, but not with wind direction. In as far as we can determine, this is the first experimental test on magnetic orientation in larger, non-homing, non-migrating mammals. These experimental and observational findings do not support previously published suggestions on the magnetic south-north alignment in these mammals. PMID:29641517

Mechanism of competitive grain growth in a curvilinear channel of crystal-sorter during the orientational solidification of nickel-based heat-resistant alloy

NASA Astrophysics Data System (ADS)

Monastyrskiy, V. P.; Pozdnyakov, A. N.; Ershov, M. Yu.; Monastyrskiy, A. V.

2017-07-01

Using numerical simulation in the ProCAST program complex, the conditions of the solidification of heat-resistant nickel alloy in curvilinear channels of a ceramic mold have been investigated. It has been shown that, in practically important cases, the vector of the temperature gradient is oriented along the axis of the curvilinear channel. In a spiral crystal selector, a cyclic change in the preferred direction of growth occurs because of the cyclic change in the direction of the vector of the temperature gradient. The fact that the vector of the temperature gradient is almost always directed along the axis of the curvilinear channel makes it possible to govern the orientation of the vector of the temperature gradient in space and, therefore, to obtain a grain with the preferred crystallographic orientation. Based on the results of this investigation, a method of the grain selection with a desired azimuthal orientation is proposed.

Sex-Specificity in the Reward Value of Facial Attractiveness.

PubMed

Hahn, Amanda C; Fisher, Claire I; DeBruine, Lisa M; Jones, Benedict C

2016-05-01

Studies of the sex-specificity of sexual arousal in adults (i.e., the tendency to respond more strongly to preferred-sex individuals than non-preferred sex individuals) have suggested that heterosexual men, homosexual men, and homosexual women show stronger sex-specific responses than do heterosexual women. Evidence for a similar pattern of results in studies investigating the reward value of faces is equivocal. Consequently, we investigated the effects of (1) sexual orientation (homosexual vs. heterosexual), (2) sex (male vs. female), (3) image sex (preferred-sex vs. non-preferred-sex), and (4) the physical attractiveness of the individual shown in the image on the reward value of faces. Participants were 130 heterosexual men, 130 homosexual men, 130 heterosexual women, and 130 homosexual women. The reward value of faces was assessed using a standard key-press task. Multilevel modeling of responses indicated that images of preferred-sex individuals were more rewarding than images of non-preferred-sex individuals and that this preferred-sex bias was particularly pronounced when more physically attractive faces were presented. These effects were not qualified by interactions involving either the sexual orientation or the sex of our participants, however, suggesting that the preferred-sex bias in the reward value of faces is similar in heterosexual men, homosexual men, heterosexual women, and homosexual women.

Bra strap orientations and designs to minimise bra strap discomfort and pressure during sport and exercise in women with large breasts.

PubMed

Coltman, Celeste E; McGhee, Deirdre E; Steele, Julie R

2015-01-01

Bra straps are a primary source of discomfort during sport and exercise, particularly for women with large breasts. This study aimed to investigate the effects of altering bra strap orientation and design on bra strap comfort, pressure and breast support in women with large breasts. This is a descriptive laboratory study. Bra strap discomfort (visual analogue scale, 0 to 10), pressure (custom-designed 10 mm 2 calibrated pressure sensor, 0.5 to 24 kPa range, 50 Hz, S2011, Novel GmbH, Munich, Germany, placed under the right bra strap at the crest of each participant's shoulder), preference ranking and vertical breast displacement (VBD; Optotrak Certus® motion capture system, 200 Hz, Northern Digital, Ontario, Canada) data during dynamic treadmill running and static upright standing (pressure only) were collected for 23 active women with large breasts (D+ cup size) while they wore an encapsulation sports bra with six different bra strap conditions (two bra strap orientations: vertical and cross-back; three bra strap designs: standard width, wide and gel). Bra strap discomfort was significantly less ( p  ≤ 0.001) in the vertical compared to the cross-back strap orientation, which was the most preferred orientation despite no significant difference in strap pressure. The wide strap design had the lowest discomfort scores, significantly lower strap pressure compared to the standard width and gel strap designs ( p  < 0.001), and was equally the most preferred design with the gel straps. There was no significant difference in VBD among the six strap conditions. Bra straps that are vertically orientated and wide (approximately 4.5 cm in width) are preferable for women with large breasts during sport and exercise to minimise bra strap pressure and discomfort. The addition of gel pads under bra straps may also decrease discomfort and prevent straps slipping off the shoulders, although this notion warrants further investigation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marimuthu, T.; Anandhan, N., E-mail: anandhan-kn@rediffmail.com; Mummoorthi, M.

Zinc oxide (ZnO) and zinc oxide/eosin yellow (ZnO/EY) thin films were potentiostatically deposited onto fluorine doped tin oxide (FTO) glass substrate. Effect of eosin yellow dye on structural, morphological and optical properties was studied. X-ray diffraction patterns, micro Raman spectra and photoluminescence (PL) spectra reveal hexagonal wurtzite structure with less atomic defects in 101 plane orientation of the ZnO/EY film. Scanning electron microscopy (SEM) images show flower for ZnO and porous like structure for ZnO/EY thin film, respectively. DSSC was constructed and evaluated by measuring the current density verses voltage curve.

Fabric analysis of quartzites with negative magnetic susceptibility - Does AMS provide information of SPO or CPO of quartz?

NASA Astrophysics Data System (ADS)

Renjith, A. R.; Mamtani, Manish A.; Urai, Janos L.

2016-01-01

We ask the question whether petrofabric data from anisotropy of magnetic susceptibility (AMS) analysis of deformed quartzites gives information about shape preferred orientation (SPO) or crystallographic preferred orientation (CPO) of quartz. Since quartz is diamagnetic and has a negative magnetic susceptibility, 11 samples of nearly pure quartzites with a negative magnetic susceptibility were chosen for this study. After performing AMS analysis, electron backscatter diffraction (EBSD) analysis was done in thin sections prepared parallel to the K1K3 plane of the AMS ellipsoid. Results show that in all the samples quartz SPO is sub-parallel to the orientation of the magnetic foliation. However, in most samples no clear correspondance is observed between quartz CPO and K1 (magnetic lineation) direction. This is contrary to the parallelism observed between K1 direction and orientation of quartz c-axis in the case of undeformed single quartz crystal. Pole figures of quartz indicate that quartz c-axis tends to be parallel to K1 direction only in the case where intracrystalline deformation of quartz is accommodated by prism slip. It is therefore established that AMS investigation of quartz from deformed rocks gives information of SPO. Thus, it is concluded that petrofabric information of quartzite obtained from AMS is a manifestation of its shape anisotropy and not crystallographic preferred orientation.

Consequences of Beauty: Effects of Rater Sex and Sexual Orientation on the Visual Exploration and Evaluation of Attractiveness in Real World Scenes

PubMed Central

Mitrovic, Aleksandra; Tinio, Pablo P. L.; Leder, Helmut

2016-01-01

One of the key behavioral effects of attractiveness is increased visual attention to attractive people. This effect is often explained in terms of evolutionary adaptations, such as attractiveness being an indicator of good health. Other factors could influence this effect. In the present study, we explored the modulating role of sexual orientation on the effects of attractiveness on exploratory visual behavior. Heterosexual and homosexual men and women viewed natural-looking scenes that depicted either two women or two men who varied systematically in levels of attractiveness (based on a pre-study). Participants’ eye movements and attractiveness ratings toward the faces of the depicted people were recorded. The results showed that although attractiveness had the largest influence on participants’ behaviors, participants’ sexual orientations strongly modulated the effects. With the exception of homosexual women, all participant groups looked longer and more often at attractive faces that corresponded with their sexual orientations. Interestingly, heterosexual and homosexual men and homosexual women looked longer and more often at the less attractive face of their non-preferred sex than the less attractive face of their preferred sex, evidence that less attractive faces of the preferred sex might have an aversive character. These findings provide evidence for the important role that sexual orientation plays in guiding visual exploratory behavior and evaluations of the attractiveness of others. PMID:27047365

Consequences of Beauty: Effects of Rater Sex and Sexual Orientation on the Visual Exploration and Evaluation of Attractiveness in Real World Scenes.

PubMed

Mitrovic, Aleksandra; Tinio, Pablo P L; Leder, Helmut

2016-01-01

One of the key behavioral effects of attractiveness is increased visual attention to attractive people. This effect is often explained in terms of evolutionary adaptations, such as attractiveness being an indicator of good health. Other factors could influence this effect. In the present study, we explored the modulating role of sexual orientation on the effects of attractiveness on exploratory visual behavior. Heterosexual and homosexual men and women viewed natural-looking scenes that depicted either two women or two men who varied systematically in levels of attractiveness (based on a pre-study). Participants' eye movements and attractiveness ratings toward the faces of the depicted people were recorded. The results showed that although attractiveness had the largest influence on participants' behaviors, participants' sexual orientations strongly modulated the effects. With the exception of homosexual women, all participant groups looked longer and more often at attractive faces that corresponded with their sexual orientations. Interestingly, heterosexual and homosexual men and homosexual women looked longer and more often at the less attractive face of their non-preferred sex than the less attractive face of their preferred sex, evidence that less attractive faces of the preferred sex might have an aversive character. These findings provide evidence for the important role that sexual orientation plays in guiding visual exploratory behavior and evaluations of the attractiveness of others.

The role of clinical experience, diagnosis, and theoretical orientation in the treatment of posttraumatic and dissociative disorders: A vignette and survey investigation.

PubMed

Dorahy, Martin J; Lewis-Fernández, Roberto; Krüger, Christa; Brand, Bethany L; Şar, Vedat; Ewing, Jan; Martínez-Taboas, Alfonso; Stavropoulos, Pam; Middleton, Warwick

2017-01-01

Controversy exists regarding the merits of exposure-based treatments for posttraumatic stress disorder (PTSD) versus a phased approach when prominent dissociative symptoms are present. The first aim of this study was to examine the degree to which diagnosing dissociation in two traumatized patients' vignettes influenced clinicians' preference for phase-oriented treatment and whether clinicians' treatment experience contributed to their treatment preference. The second aim was to assess the extent to which participants had observed traumatized patients worsen when treated with exposure therapy or phase-oriented therapy and whether the theoretical orientation and treatment experience of the clinician were related to the observed deterioration. In the tradition of expert and practitioner surveys, 263 clinicians completed a survey of their diagnoses and treatment preferences for two vignettes and their treatment experience, theoretical orientation, and observations of patients' deterioration. When a marked degree of dissociation was noted in the PTSD vignette, respondents favored phased approaches regardless of the diagnosis given. Reports of having observed patient deterioration during both exposure and phased therapy were predicted by years of experience. Psychodynamic therapists reported more observations of worsening during exposure therapy than cognitive behavior therapy therapists. Clinical experience treating PTSD may heighten awareness of negative therapeutic effects, potentially because experienced clinicians have a lower threshold for detecting such effects and because they are referred more challenging cases.

Demonstration of Tuning to Stimulus Orientation in the Human Visual Cortex: A High-Resolution fMRI Study with a Novel Continuous and Periodic Stimulation Paradigm

PubMed Central

Sun, Pei; Gardner, Justin L.; Costagli, Mauro; Ueno, Kenichi; Waggoner, R. Allen; Tanaka, Keiji; Cheng, Kang

2013-01-01

Cells in the animal early visual cortex are sensitive to contour orientations and form repeated structures known as orientation columns. At the behavioral level, there exist 2 well-known global biases in orientation perception (oblique effect and radial bias) in both animals and humans. However, their neural bases are still under debate. To unveil how these behavioral biases are achieved in the early visual cortex, we conducted high-resolution functional magnetic resonance imaging experiments with a novel continuous and periodic stimulation paradigm. By inserting resting recovery periods between successive stimulation periods and introducing a pair of orthogonal stimulation conditions that differed by 90° continuously, we focused on analyzing a blood oxygenation level-dependent response modulated by the change in stimulus orientation and reliably extracted orientation preferences of single voxels. We found that there are more voxels preferring horizontal and vertical orientations, a physiological substrate underlying the oblique effect, and that these over-representations of horizontal and vertical orientations are prevalent in the cortical regions near the horizontal- and vertical-meridian representations, a phenomenon related to the radial bias. Behaviorally, we also confirmed that there exists perceptual superiority for horizontal and vertical orientations around horizontal and vertical meridians, respectively. Our results, thus, refined the neural mechanisms of these 2 global biases in orientation perception. PMID:22661413

Subcortical orientation biases explain orientation selectivity of visual cortical cells.

PubMed

Vidyasagar, Trichur R; Jayakumar, Jaikishan; Lloyd, Errol; Levichkina, Ekaterina V

2015-04-01

The primary visual cortex of carnivores and primates shows an orderly progression of domains of neurons that are selective to a particular orientation of visual stimuli such as bars and gratings. We recorded from single-thalamic afferent fibers that terminate in these domains to address the issue whether the orientation sensitivity of these fibers could form the basis of the remarkable orientation selectivity exhibited by most cortical cells. We first performed optical imaging of intrinsic signals to obtain a map of orientation domains on the dorsal aspect of the anaesthetized cat's area 17. After confirming using electrophysiological recordings the orientation preferences of single neurons within one or two domains in each animal, we pharmacologically silenced the cortex to leave only the afferent terminals active. The inactivation of cortical neurons was achieved by the superfusion of either kainic acid or muscimol. Responses of single geniculate afferents were then recorded by the use of high impedance electrodes. We found that the orientation preferences of the afferents matched closely with those of the cells in the orientation domains that they terminated in (Pearson's r = 0.633, n = 22, P = 0.002). This suggests a possible subcortical origin for cortical orientation selectivity. © 2015 The Authors. Physiological Reports published by Wiley Periodicals, Inc. on behalf of the American Physiological Society and The Physiological Society.

Layperson's preference regarding orientation of the transverse occlusal plane and commissure line from the frontal perspective.

PubMed

Silva, Bruno Pereira; Jiménez-Castellanos, Emilio; Finkel, Sivan; Macias, Inmaculada Redondo; Chu, Stephen J

2017-04-01

Facial asymmetries in features such as lip commissure and interpupillary plane canting have been described as common conditions affecting smile esthetics. When presented with these asymmetries, the clinician must choose the reference line with which to orient the transverse occlusal plane of the planned dental restorations. The purpose of the online survey described in this study was to determine lay preferences regarding the transverse occlusal plane orientation in faces that display a cant of the commissure line viewed from the frontal perspective. From a digitally created symmetrical facial model with the transverse occlusal plane and commissure line parallel to the interpupillary line (horizontal) and a model constructed in a previous study (control), a new facial model was created with 3 degrees of cant of the commissure line. Three digital tooth mountings were designed with different transverse occlusal plane orientations: parallel to the interpupillary line (A), parallel to the commissure line (B), and the mean angulation plane formed between the interpupillary and commissure line (C), resulting in a total of 4 images. All images, including the control, were organized into 6 pairs and evaluated by 247 selected laypersons through an online Web site survey. Each participant was asked to choose the more attractive face from each of the 6 pairs of images. The control image was preferred by 72.9% to 74.5% of the participants compared with the other 3 images, all of which represented a commissure line cant. Among the 3 pairs which represent a commissure line cant, 59.1% to 61.1% preferred a transverse plane of occlusion cant (B and C) compared with a plane of occlusion parallel to the interpupillary, line and 61.1% preferred a plane of occlusion parallel to the commissure line (B) compared with the mean angulation plane (C). Laypeople prefer faces with a commissure line and transverse occlusal plane parallel to the horizontal plane or horizon. When faces present a commissure line cant, laypeople prefer a transverse occlusal plane with a similar and coincident cant. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Comparative analysis of germanium-silicon quantum dots formation on Si(100), Si(111) and Sn/Si(100) surfaces

NASA Astrophysics Data System (ADS)

Lozovoy, Kirill; Kokhanenko, Andrey; Voitsekhovskii, Alexander

2018-02-01

In this paper theoretical modeling of formation and growth of germanium-silicon quantum dots in the method of molecular beam epitaxy (MBE) on different surfaces is carried out. Silicon substrates with crystallographic orientations (100) and (111) are considered. Special attention is paid to the question of growth of quantum dots on the silicon surface covered by tin, since germanium-silicon-tin system is extremely important for contemporary nano- and optoelectronics: for creation of photodetectors, solar cells, light-emitting diodes, and fast-speed transistors. A theoretical approach for modeling growth processes of such semiconductor compounds during the MBE is presented. Both layer-by-layer and island nucleation stages in the Stranski-Krastanow growth mode are described. A change in free energy during transition of atoms from the wetting layer to an island, activation barrier of the nucleation, critical thickness of 2D to 3D transition, as well as surface density and size distribution function of quantum dots in these systems are calculated with the help of the established model. All the theoretical speculations are carried out keeping in mind possible device applications of these materials. In particular, it is theoretically shown that using of the Si(100) surface covered by tin as a substrate for Ge deposition may be very promising for increasing size homogeneity of quantum dot array for possible applications in low-noise selective quantum dot infrared photodetectors.

Comparative analysis of germanium-silicon quantum dots formation on Si(100), Si(111) and Sn/Si(100) surfaces.

PubMed

Lozovoy, Kirill; Kokhanenko, Andrey; Voitsekhovskii, Alexander

2018-02-02

In this paper theoretical modeling of formation and growth of germanium-silicon quantum dots in the method of molecular beam epitaxy (MBE) on different surfaces is carried out. Silicon substrates with crystallographic orientations (100) and (111) are considered. Special attention is paid to the question of growth of quantum dots on the silicon surface covered by tin, since germanium-silicon-tin system is extremely important for contemporary nano- and optoelectronics: for creation of photodetectors, solar cells, light-emitting diodes, and fast-speed transistors. A theoretical approach for modeling growth processes of such semiconductor compounds during the MBE is presented. Both layer-by-layer and island nucleation stages in the Stranski-Krastanow growth mode are described. A change in free energy during transition of atoms from the wetting layer to an island, activation barrier of the nucleation, critical thickness of 2D to 3D transition, as well as surface density and size distribution function of quantum dots in these systems are calculated with the help of the established model. All the theoretical speculations are carried out keeping in mind possible device applications of these materials. In particular, it is theoretically shown that using of the Si(100) surface covered by tin as a substrate for Ge deposition may be very promising for increasing size homogeneity of quantum dot array for possible applications in low-noise selective quantum dot infrared photodetectors.

Axon topography of layer 6 spiny cells to orientation map in the primary visual cortex of the cat (area 18).

PubMed

Karube, Fuyuki; Sári, Katalin; Kisvárday, Zoltán F

2017-04-01

To uncover the functional topography of layer 6 neurons, optical imaging was combined with three-dimensional neuronal reconstruction. Apical dendrite morphology of 23 neurons revealed three distinct types. Type Aa possessed a short apical dendrite with many oblique branches, Type Ab was characterized by a short and less branched apical dendrite, whereas Type B had a long apical dendrite with tufts in layer 2. Each type had a similar number of boutons, yet their spatial distribution differed from each other in both radial and horizontal extent. Boutons of Type Aa and Ab were almost restricted to the column of the parent soma with a laminar preference to layer 4 and 5/6, respectively. Only Type B contributed to long horizontal connections (up to 1.5 mm) mostly in deep layers. For all types, bouton distribution on orientation map showed an almost equal occurrence at iso- (52.6 ± 18.8 %) and non-iso-orientation (oblique, 27.7 ± 14.9 % and cross-orientation 19.7 ± 10.9 %) sites. Spatial convergence of axons of nearby layer 6 spiny neurons depended on soma separation of the parent cells, but only weakly on orientation preference, contrary to orientation dependence of converging axons of layer 4 spiny cells. The results show that layer 6 connections have only a weak dependence on orientation preference compared with those of layers 2/3 (Buzás et al., J Comp Neurol 499:861-881, 2006) and 4 (Karube and Kisvárday, Cereb Cortex 21:1443-1458, 2011).

X-ray texture analysis of paper coating pigments and the correlation with chemical composition analysis

NASA Astrophysics Data System (ADS)

Roine, J.; Tenho, M.; Murtomaa, M.; Lehto, V.-P.; Kansanaho, R.

2007-10-01

The present research experiments the applicability of x-ray texture analysis in investigating the properties of paper coatings. The preferred orientations of kaolin, talc, ground calcium carbonate, and precipitated calcium carbonate particles used in four different paper coatings were determined qualitatively based on the measured crystal orientation data. The extent of the orientation, namely, the degree of the texture of each pigment, was characterized quantitatively using a single parameter. As a result, the effect of paper calendering is clearly seen as an increase on the degree of texture of the coating pigments. The effect of calendering on the preferred orientation of kaolin was also evident in an independent energy dispersive spectrometer analysis on micrometer scale and an electron spectroscopy for chemical analysis on nanometer scale. Thus, the present work proves x-ray texture analysis to be a potential research tool for characterizing the properties of paper coating layers.

Onset and evolution of laser induced periodic surface structures on indium tin oxide thin films for clean ablation using a repetitively pulsed picosecond laser at low fluence

NASA Astrophysics Data System (ADS)

Farid, N.; Dasgupta, P.; O’Connor, G. M.

2018-04-01

The onset and evolution of laser induced periodic surface structures (LIPSS) is of key importance to obtain clean ablated features on indium tin oxide (ITO) thin films at low fluences. The evolution of subwavelength periodic nanostructures on a 175 nm thick ITO film, using 10 ps laser pulses at a wavelength of 1032 nm, operating at 400 kHz, is investigated. Initially nanoblisters are observed when a single pulse is applied below the damage threshold fluence (0.45 J cm‑2) the size and distribution of nanoblisters are found to depend on fluence. Finite difference time domain (FDTD) simulations support the hypothesis that conductive nanoblisters can enhance the local intensity of the applied electromagnetic field. The LIPSS are observed to evolve from regions where the electric field enhancement has occurred; LIPSS has a perpendicular orientation relative to the laser polarization for a small number (<5) of applied pulses. The LIPSS periodicity depends on nanoblister size and distribution; a periodicity down to 100 nm is observed at the lower fluence periphery of the Gaussian irradiated area where nanoblisters are smallest and more closely arranged. Upon irradiation with successive (>5) pulses, the orientation of the periodic structures appears to rotate and evolve to become aligned in parallel with the laser polarization at approximately the same periodicity. These orientation effects are not observed at higher fluence—due to the absence of the nanoblister-like structures; this apparent rotation is interpreted to be due to stress-induced fragmentation of the LIPSS structure. The application of subsequent pulses leads to clean ablation. LIPSS are further modified into features of a shorter period when laser scanning is used. Results provide evidence that the formation of conductive nanoblisters leads to the enhancement of the applied electromagnetic field and thereby can be used to precisely control laser ablation on ITO thin films.

The Relative Importance of Language in Guiding Social Preferences Through Development

PubMed Central

Esseily, Rana; Somogyi, Eszter; Guellai, Bahia

2016-01-01

In this paper, we review evidence from infants, toddlers, and preschoolers to tackle the question of how individuals orient preferences and actions toward social partners and how these preferences change over development. We aim at emphasizing the importance of language in guiding categorization relatively to other cues such as age, race and gender. We discuss the importance of language as part of a communication system that orients infants and older children’s attention toward relevant information in their environment and toward affiliated social partners who are potential sources of knowledge. We argue that other cues (visually perceptible features) are less reliable in informing individuals whether others share a common knowledge and whether they can be source of information. PMID:27812345

The Relative Importance of Language in Guiding Social Preferences Through Development.

PubMed

Esseily, Rana; Somogyi, Eszter; Guellai, Bahia

2016-01-01

In this paper, we review evidence from infants, toddlers, and preschoolers to tackle the question of how individuals orient preferences and actions toward social partners and how these preferences change over development. We aim at emphasizing the importance of language in guiding categorization relatively to other cues such as age, race and gender. We discuss the importance of language as part of a communication system that orients infants and older children's attention toward relevant information in their environment and toward affiliated social partners who are potential sources of knowledge. We argue that other cues (visually perceptible features) are less reliable in informing individuals whether others share a common knowledge and whether they can be source of information.

Gravity orientation tuning in macaque anterior thalamus.

PubMed

Laurens, Jean; Kim, Byounghoon; Dickman, J David; Angelaki, Dora E

2016-12-01

Gravity may provide a ubiquitous allocentric reference to the brain's spatial orientation circuits. Here we describe neurons in the macaque anterior thalamus tuned to pitch and roll orientation relative to gravity, independently of visual landmarks. We show that individual cells exhibit two-dimensional tuning curves, with peak firing rates at a preferred vertical orientation. These results identify a thalamic pathway for gravity cues to influence perception, action and spatial cognition.

Strong Recurrent Networks Compute the Orientation-Tuning of Surround Modulation in Primate V1

PubMed Central

Shushruth, S.; Mangapathy, Pradeep; Ichida, Jennifer M.; Bressloff, Paul C.; Schwabe, Lars; Angelucci, Alessandra

2012-01-01

In macaque primary visual cortex (V1) neuronal responses to stimuli inside the receptive field (RF) are modulated by stimuli in the RF surround. This modulation is orientation-specific. Previous studies suggested that for some cells this specificity may not be fixed, but changes with the stimulus orientation presented to the RF. We demonstrate, in recording studies, that this tuning behavior is instead highly prevalent in V1 and, in theoretical work, that it arises only if V1 operates in a regime of strong local recurrence. Strongest surround suppression occurs when the stimuli in the RF and the surround are iso-oriented, and strongest facilitation when the stimuli are cross-oriented. This is the case even when the RF is sub-optimally activated by a stimulus of non-preferred orientation, but only if this stimulus can activate the cell when presented alone. This tuning behavior emerges from the interaction of lateral inhibition (via the surround pathways), which is tuned to the RF’s preferred orientation, with weakly-tuned, but strong, local recurrent connections, causing maximal withdrawal of recurrent excitation at the feedforward input orientation. Thus, horizontal and feedback modulation of strong recurrent circuits allows the tuning of contextual effects to change with changing feedforward inputs. PMID:22219292

Adaptation Shifts Preferred Orientation of Tuning Curve in the Mouse Visual Cortex

PubMed Central

Jeyabalaratnam, Jeyadarshan; Bharmauria, Vishal; Bachatene, Lyes; Cattan, Sarah; Angers, Annie; Molotchnikoff, Stéphane

2013-01-01

In frontalized mammals it has been demonstrated that adaptation produces shift of the peak of the orientation tuning curve of neuron following frequent or lengthier presentation of a non-preferred stimulus. Depending on the duration of adaptation the shift is attractive (toward the adapter) or repulsive (away from the adapter). Mouse exhibits a salt-and-pepper cortical organization of orientation maps, hence this species may respond differently to adaptation. To examine this question, we determined the effect of twelve minutes of adaptation to one particular orientation on neuronal orientation tuning curves in V1 of anesthetized mice. Multi-unit activity of neurons in V1 was recorded in a conventional fashion. Cells were stimulated with sine-wave drifting gratings whose orientation tilted in steps. Results revealed that similarly to cats and monkeys, majority of cells shifted their optimal orientation in the direction of the adapter while a small proportion exhibited a repulsive shift. Moreover, initially untuned cells showing poor tuning curves reacted to adaptation by displaying sharp orientation selectivity. It seems that modification of the cellular property following adaptation is a general phenomenon observed in all mammals in spite of the different organization pattern of the visual cortex. This study is of pertinence to comprehend the mechanistic pathways of brain plasticity. PMID:23717586

Effect of substrates on the molecular orientation of silicon phthalocyanine dichloride thin films

NASA Astrophysics Data System (ADS)

Deng, Juzhi; Baba, Yuji; Sekiguchi, Tetsuhiro; Hirao, Norie; Honda, Mitsunori

2007-05-01

Molecular orientations of silicon phthalocyanine dichloride (SiPcCl2) thin films deposited on three different substrates have been measured by near-edge x-ray absorption fine structure (NEXAFS) spectroscopy using linearly polarized synchrotron radiation. The substrates investigated were highly oriented pyrolitic graphite (HOPG), polycrystalline gold and indium tin oxide (ITO). For thin films of about five monolayers, the polarization dependences of the Si K-edge NEXAFS spectra showed that the molecular planes of SiPcCl2 on three substrates were nearly parallel to the surface. Quantitative analyses of the polarization dependences revealed that the tilted angle on HOPG was only 2°, which is interpreted by the perfect flatness of the HOPG surface. On the other hand, the tilted angle on ITO was 26°. Atomic force microscopy (AFM) observation of the ITO surface showed that the periodicity of the horizontal roughness is of the order of a few nanometres, which is larger than the molecular size of SiPcCl2. It is concluded that the morphology of the top surface layer of the substrate affects the molecular orientation of SiPcCl2 molecules not only for mono-layered adsorbates but also for multi-layered thin films.

The Relation between Gender Role Orientation and Fear and Anxiety in Nonclinic-Referred Children

ERIC Educational Resources Information Center

Muris, Peter; Meesters, Cor; Knoops, Miranda

2005-01-01

This study examined the relation between gender role orientation and fear and anxiety in a sample of nonclinic-referred children (N = 209) ages 10 to 13 years. Children and their parents completed questionnaires assessing children's gender role orientation, toy and activity preferences, and fear and anxiety. Results generally indicated that…

On the Life Orientations of the Young People of the Volga Region

ERIC Educational Resources Information Center

Iavon, S. V.

2011-01-01

Social and economic transformations in Russia have had an influence on all spheres of society. The value orientations of young people have been influenced by the market economy, and this has led to a new type of adaptive behavior, in which preference is given to material value orientations, growth of individualism, pragmatism, and hedonistic…

The Dynamic and Correlation of the Value Orientations and Life Goals of Urban Adolescents

ERIC Educational Resources Information Center

Selivanova, Z. K.

2014-01-01

One of the scientific techniques in the study of value orientations and preferences consists of determining adolescents' attitudes toward personality qualities. It is well known that the model of a personality as an ideal construct formed in a person's consciousness correlates with value orientations and life goals. Its study permits us to…

The ovine sexually dimorphic nucleus, aromatase, and sexual partner preferences in sheep.

PubMed

Roselli, C E; Stormshak, F

2010-02-28

We are using the domestic ram as an experimental model to examine the role of aromatase in the development of sexual partner preferences. This interest has arisen because of the observation that as many as 8% of domestic rams are sexually attracted to other rams (male-oriented) in contrast to the majority of rams that are attracted to estrous ewes (female-oriented). Our findings demonstrate that aromatase expression is enriched in a cluster of neurons in the medial preoptic nucleus called the ovine sexually dimorphic nucleus (oSDN). The size of the oSDN is associated with a ram's sexual partner preference, such that the nucleus is 2-3 times larger in rams that are attracted to females (female-oriented) than in rams that are attracted to other rams (male-oriented). Moreover, the volume of the oSDN in male-oriented rams is similar to the volume in ewes. These volume differences are not influenced by adult concentrations of serum testosterone. Instead, we found that the oSDN is already present in late gestation lamb fetuses (approximately day 135 of gestation) when it is approximately 2-fold greater in males than in females. Exposure of genetic female fetuses to exogenous testosterone during the critical period for sexual differentiation masculinizes oSDN volume and aromatase expression when examined subsequently on day 135. The demonstration that the oSDN is organized prenatally by testosterone exposure suggests that the brain of the male-oriented ram may be under-androgenized during development. Copyright 2009 Elsevier Ltd. All rights reserved.

Analysis of Crystallographic Structure of a Japanese Sword by the Pulsed Neutron Transmission Method

NASA Astrophysics Data System (ADS)

Kino, K.; Ayukawa, N.; Kiyanagi, Y.; Uchida, T.; Uno, S.; Grazzi, F.; Scherillo, A.

We measured two-dimensional transmission spectra of pulsed neutron beams for a Japanese sword sample. Atom density, crystalline size, and preferred orientation of crystals were obtained using the RITS code. The position dependence of the atomic density is consistent with the shape of the sample. The crystalline size is very small and shows position dependence, which is understood by the unique structure of Japanese swords. The preferred orientation has strong position dependence. Our study shows the usefulness of the pulsed neutron transmission method for cultural metal artifacts.

Ab-initio simulations on adhesion and material transfer between contacting Al and TiN surfaces

NASA Astrophysics Data System (ADS)

Feldbauer, Gregor; Wolloch, Michael; Mohn, Peter; Redinger, Josef; Vernes, Andras

2014-03-01

Contacts of surfaces at the atomic scale are crucial in many modern applications from analytical techniques like indentation or AFM experiments to technologies such as nano- and micro-electro-mechanical-systems (N-/M-EMS). Furthermore, detailed insights into such contacts are fundamental for a better understanding of tribological processes like wear. A series of simulations is performed within the framework of Density Functional Theory (DFT) to investigate the approaching, contact and subsequent separation of two atomically flat surfaces consisting of different materials. Aluminum (Al) and titanium-nitride (TiN) slabs have been chosen as a model system representing the interaction between a soft and a hard material. The approaching and separation is simulated by moving one slab in discrete steps and allowing for electronic and ionic relaxations after each one. The simulations reveal the influences of different surface orientations ((001), (011), (111)) and alignments of the surfaces with respect to each other on the adhesion, equilibrium distance, charge distribution and material transfer between the surfaces. Material transfer is observed for configurations where the interface is stronger than the softer material.

Transcriptional interference networks coordinate the expression of functionally related genes clustered in the same genomic loci

PubMed Central

Boldogköi, Zsolt

2012-01-01

The regulation of gene expression is essential for normal functioning of biological systems in every form of life. Gene expression is primarily controlled at the level of transcription, especially at the phase of initiation. Non-coding RNAs are one of the major players at every level of genetic regulation, including the control of chromatin organization, transcription, various post-transcriptional processes, and translation. In this study, the Transcriptional Interference Network (TIN) hypothesis was put forward in an attempt to explain the global expression of antisense RNAs and the overall occurrence of tandem gene clusters in the genomes of various biological systems ranging from viruses to mammalian cells. The TIN hypothesis suggests the existence of a novel layer of genetic regulation, based on the interactions between the transcriptional machineries of neighboring genes at their overlapping regions, which are assumed to play a fundamental role in coordinating gene expression within a cluster of functionally linked genes. It is claimed that the transcriptional overlaps between adjacent genes are much more widespread in genomes than is thought today. The Waterfall model of the TIN hypothesis postulates a unidirectional effect of upstream genes on the transcription of downstream genes within a cluster of tandemly arrayed genes, while the Seesaw model proposes a mutual interdependence of gene expression between the oppositely oriented genes. The TIN represents an auto-regulatory system with an exquisitely timed and highly synchronized cascade of gene expression in functionally linked genes located in close physical proximity to each other. In this study, we focused on herpesviruses. The reason for this lies in the compressed nature of viral genes, which allows a tight regulation and an easier investigation of the transcriptional interactions between genes. However, I believe that the same or similar principles can be applied to cellular organisms too. PMID:22783276

Transcriptional interference networks coordinate the expression of functionally related genes clustered in the same genomic loci.

PubMed

Boldogköi, Zsolt

2012-01-01

The regulation of gene expression is essential for normal functioning of biological systems in every form of life. Gene expression is primarily controlled at the level of transcription, especially at the phase of initiation. Non-coding RNAs are one of the major players at every level of genetic regulation, including the control of chromatin organization, transcription, various post-transcriptional processes, and translation. In this study, the Transcriptional Interference Network (TIN) hypothesis was put forward in an attempt to explain the global expression of antisense RNAs and the overall occurrence of tandem gene clusters in the genomes of various biological systems ranging from viruses to mammalian cells. The TIN hypothesis suggests the existence of a novel layer of genetic regulation, based on the interactions between the transcriptional machineries of neighboring genes at their overlapping regions, which are assumed to play a fundamental role in coordinating gene expression within a cluster of functionally linked genes. It is claimed that the transcriptional overlaps between adjacent genes are much more widespread in genomes than is thought today. The Waterfall model of the TIN hypothesis postulates a unidirectional effect of upstream genes on the transcription of downstream genes within a cluster of tandemly arrayed genes, while the Seesaw model proposes a mutual interdependence of gene expression between the oppositely oriented genes. The TIN represents an auto-regulatory system with an exquisitely timed and highly synchronized cascade of gene expression in functionally linked genes located in close physical proximity to each other. In this study, we focused on herpesviruses. The reason for this lies in the compressed nature of viral genes, which allows a tight regulation and an easier investigation of the transcriptional interactions between genes. However, I believe that the same or similar principles can be applied to cellular organisms too.

Ab initio studies on the adsorption and implantation of Al and Fe to nitride materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Riedl, H., E-mail: helmut.riedl@tuwien.ac.at; Zálešák, J.; Department of Physical Metallurgy and Materials Testing, Montanuniversität Leoben, A-8700 Leoben

2015-09-28

The formation of transfer material products on coated cutting and forming tools is a major failure mechanism leading to various sorts of wear. To describe the atomistic processes behind the formation of transfer materials, we use ab initio to study the adsorption energy as well as the implantation barrier of Al and Fe atoms for (001)-oriented surfaces of TiN, Ti{sub 0.50}Al{sub 0.50}N, Ti{sub 0.90}Si{sub 0.10}N, CrN, and Cr{sub 0.90}Si{sub 0.10}N. The interactions between additional atoms and nitride-surfaces are described for pure adhesion, considering no additional stresses, and for the implantation barrier. The latter, we simplified to the stress required tomore » implant Al and Fe into sub-surface regions of the nitride material. The adsorption energies exhibit pronounced extrema at high-symmetry positions and are generally highest at nitrogen sites. Here, the binary nitrides are comparable to their ternary counterparts and the average adhesive energy is higher (more negative) on CrN than TiN based systems. Contrary, the implantation barrier for Al and Fe atoms is higher for the ternary systems Ti{sub 0.50}Al{sub 0.50}N, Ti{sub 0.90}Si{sub 0.10}N, and Cr{sub 0.90}Si{sub 0.10}N than for their binary counterparts TiN and CrN. Based on our results, we can conclude that TiN based systems outperform CrN based systems with respect to pure adhesion, while the Si-containing ternaries exhibit higher implantation barriers for Al and Fe atoms. The data obtained are important to understand the atomistic interaction of metal atoms with nitride-based materials, which is valid not just for machining operations but also for any combination such as interfaces between coatings and substrates or multilayer and phase arrangements themselves.« less

Structural, optical and electrochemical properties of F-doped vanadium oxide transparent semiconducting thin films

NASA Astrophysics Data System (ADS)

Mousavi, M.; Khorrami, Gh. H.; Kompany, A.; Yazdi, Sh. Tabatabai

2017-12-01

In this study, F-doped vanadium oxide thin films with doping levels up to 60 at % were prepared by spray pyrolysis method on glass substrates. To measure the electrochemical properties, some films were deposited on fluorine-tin oxide coated glass substrates. The effect of F-doping on the structural, electrical, optical and electrochemical properties of vanadium oxide samples was investigated. The X-ray diffractographs analysis has shown that all the samples grow in tetragonal β-V2O5 phase structure with the preferred orientation of [200]. The intensity of (200) peak belonging to β-V2O5 phase was strongest in the undoped vanadium oxide film. The scanning electron microscopy images show that the samples have nanorod- and nanobelt-shaped structure. The size of the nanobelts in the F-doped vanadium oxide films is smaller than that in the pure sample and the width of the nanobelts increases from 30 to 70 nm with F concentration. With increasing F-doping level from 10 to 60 at %, the resistivity, the transparency and the optical band gap decrease from 111 to 20 Ω cm, 70 to 50% and 2.4 to 2.36 eV, respectively. The cyclic voltammogram (CV) results show that the undoped sample has the most extensive CV and by increasing F-doping level from 20 to 60 at %, the area of the CV is expanded. The anodic and cathodic peaks in F-doped samples are stronger.

Synthesis and Characterization of Tin(IV) Oxide Obtained by Chemical Vapor Deposition Method

NASA Astrophysics Data System (ADS)

Nagirnyak, Svitlana V.; Lutz, Victoriya A.; Dontsova, Tatiana A.; Astrelin, Igor M.

2016-07-01

The effect of precursors on the characteristics of tin oxide obtained by chemical vapor deposition (CVD) method was investigated. The synthesis of nanosized tin(IV) oxide was carried out with the use of two different precursors: tin(II) oxalate obtained using tin chloride(II) and oxalic acid; tin(II) oxalate obtained using tin chloride(II); and ammonium oxalate. The synthesized tin(IV) oxide samples were studied by electron microscopy, X-ray diffraction and optical spectra. The lattice parameters of tin(IV) oxide samples were defined, the bandgap of samples were calculated.

Birth Position, Neonatal Head Position Preference, and Hand Preference in 19-Week-Old-Infants.

ERIC Educational Resources Information Center

Goodwin, Rhoda S.

This study investigated the hypotheses that 1) infants delivered from a left occiput anterior or transverse position (LOA/LOT) would exhibit a right supine head orientation in the neonatal examination and a right hand preference at 19 weeks of age; and 2) infants delivered from a right occiput anterior or transverse position (ROA/ROT) would…

International strategic minerals inventory summary report; tin

USGS Publications Warehouse

Sutphin, D.M.; Sabin, A.E.; Reed, B.L.

1990-01-01

The International Strategic Minerals Inventory tin inventory contains records for 56 major tin deposits and districts in 21 countries. These countries accounted for 98 percent of the 10 million metric tons of tin produced in the period 1934-87. Tin is a good alloying metal and is generally nontoxic, and its chief uses are as tinplate for tin cans and as solder in electronics. The 56 locations consist of 39 lode deposits and 17 placers and contain almost 7.5 million metric tons of tin in identified economic resources (R1E) and another 1.5 million metric tons of tin in other resource categories. Most of these resources are in major deposits that have been known for over a hundred years. Lode deposits account for 44 percent of the R1E and 87 percent of the resources in other categories. Placer deposits make up the remainder. Low-income and middle-income countries, including Bolivia and Brazil and countries along the Southeast Asian Tin Belt such as Malaysia, Thailand, and Indonesia account for 91 percent of the R1E resources of tin and for 61 percent of resources in other categories. The United States has less than 0.05 percent of the world's tin R1E in major deposits. Available data suggest that the Soviet Union may have about 4 percent of resources in this category. The industrial market economy countries of the United States, Japan, Federal Republic of Germany, and the United Kingdom are major consumers of tin, whereas the major tin-producing countries generally consume little tin. The Soviet Union and China are both major producers and consumers of tin. At the end of World War II, the four largest tin-producing countries (Bolivia, the Belgian Congo (Zaire), Nigeria, and Malaysia) produced over 80 percent of the world's tin. In 1986, the portion of production from the four largest producers (Malaysia, Brazil, Soviet Union, Indonesia) declined to about 55 percent, while the price of tin rose from about $1,500 to $18,000 per metric ton. In response to tin shortages during World War II, the United States began stockpiling refined tin metal from approximately 1946 to 1953 to ensure a strategic supply in the event of another war. Since World War II, there have been six International Tin Agreements to maintain price and supply stability between tin producers and consumers. Artificially high prices set by the tin-producing members and a tin glut brought on by independent producers like Brazil caused the collapse of the world tin market in late 1985; the International Tin Council exhausted its credit to support the market price. By the year 2025, Bolivia's underground lode mines will likely have insignificant production, as will those in the United Kingdom. Tin mines in the Southeast Asian Tin Belt will still be active. Brazil, which has risen from the eighth-ranked tin-producing country in 1982 to the largest producer in 1988, will likely be a major influence on world tin production well into the 21st century. The future mining activity of deposits presently inactive in Australia is impossible to predict.

Cells Recognize and Prefer Bone-like Hydroxyapatite: Biochemical Understanding of Ultrathin Mineral Platelets in Bone.

PubMed

Liu, Cuilian; Zhai, Halei; Zhang, Zhisen; Li, Yaling; Xu, Xurong; Tang, Ruikang

2016-11-09

Hydroxyapatite (HAP) nanocrystallites in all types of bones are distinguished by their ultrathin characteristics, which are uniaxially oriented with fibrillar collagen to uniquely expose the (100) faces. We speculate that living organisms prefer the specific crystal morphology and orientation of HAP because of the interactions between cells and crystals at the mineral-cell interface. Here, bone-like platy HAP (p-HAP) and two different rod-like HAPs were synthesized to investigate the ultrathin mineral modulating effect on cell bioactivity and bone generation. Cell viability and osteogenic differentiation of mesenchymal stem cells (MSCs) were significantly promoted by the platy HAP with (100) faces compared to rod-like HAPs with (001) faces as the dominant crystal orientation, which indicated that MSCs can recognize the crystal face and prefer the (100) HAP faces. This face-specific preference is dependent on the selective adsorption of fibronectin (FN), a plasma protein that plays a central role in cell adhesion, on the HAP surface. This selective adsorption is further confirmed by molecule dynamics (MD) simulation. Our results demonstrate that it is an intelligent choice for cells to use ultrathin HAP with a large (100) face as a basic building block in the hierarchical structure of bone, which is crucial to the promotion of MSCs osteoinductions during bone formation.

Veteran satisfaction and treatment preferences in response to a posttraumatic stress disorder specialty clinic orientation group.

PubMed

Schumm, Jeremiah A; Walter, Kristen H; Bartone, Anne S; Chard, Kathleen M

2015-06-01

To maximize accessibility to evidence-based treatments for posttraumatic stress disorder (PTSD), the United States Department of Veterans Affairs (VA) has widely disseminated cognitive processing therapy (CPT) and prolonged exposure (PE) therapy to VA clinicians. However, there is a lack of research on veteran preferences when presented with a range of psychotherapy and medication options. This study uses a mixed-method approach to explore veteran satisfaction with a VA PTSD specialty clinic pre-treatment orientation group, which provides education about available PTSD treatment options. This study also tested differences in treatment preference in response to the group. Participants were 183 US veterans. Most were White, male, and referred to the clinic by a VA provider. Results indicated high satisfaction with the group in providing an overview of services and helping to inform treatment choice. Most preferred psychotherapy plus medications (63.4%) or psychotherapy only (30.1%). Participants endorsed a significantly stronger preference for CPT versus other psychotherapies. PE was significantly preferred over nightmare resolution therapy and present-centered therapy, and both PE and cognitive-behavioral conjoint therapy were preferred over virtual reality exposure therapy. Results suggest that by informing consumers about evidence-based treatments for PTSD, pre-treatment educational approaches may increase consumer demand for these treatment options. Published by Elsevier Ltd.

Electrode with transparent series resistance for uniform switching of optical modulation devices

DOEpatents

Tench, D Morgan [Camarillo, CA; Cunningham, Michael A [Thousand Oaks, CA; Kobrin, Paul H [Newbury Park, CA

2008-01-08

Switching uniformity of an optical modulation device for controlling the propagation of electromagnetic radiation is improved by use of an electrode comprising an electrically resistive layer that is transparent to the radiation. The resistive layer is preferably an innerlayer of a wide-bandgap oxide sandwiched between layers of indium tin oxide or another transparent conductor, and may be of uniform thickness, or may be graded so as to provide further improvement in the switching uniformity. The electrode may be used with electrochromic and reversible electrochemical mirror (REM) smart window devices, as well as display devices based on various technologies.

On the use of response surface methodology to predict and interpret the preferred c-axis orientation of sputtered AlN thin films

NASA Astrophysics Data System (ADS)

Adamczyk, J.; Horny, N.; Tricoteaux, A.; Jouan, P.-Y.; Zadam, M.

2008-01-01

This paper deals with experimental design applied to response surface methodology (RSM) in order to determine the influence of the discharge conditions on preferred c-axis orientation of sputtered AlN thin films. The thin films have been deposited by DC reactive magnetron sputtering on Si (1 0 0) substrates. The preferred orientation was evaluated using a conventional Bragg-Brentano X-ray diffractometer ( θ-2 θ) with the CuKα radiation. We have first determined the experimental domain for 3 parameters: sputtering pressure (2-6 mTorr), discharge current (312-438 mA) and nitrogen percentage (17-33%). For the setup of the experimental design we have used a three factors Doehlert matrix which allows the use of the statistical response surface methodology (RSM) in a spherical domain. A four dimensional surface response, which represents the (0 0 0 2) peak height as a function of sputtering pressure, discharge current and nitrogen percentage, was obtained. It has been found that the main interaction affecting the preferential c-axis orientation was the pressure-nitrogen percentage interaction. It has been proved that a Box-Cox transformation is a very useful method to interpret and discuss the experimental results and leads to predictions in good agreement with experiments.

Revealing the preferred interlayer orientations and stackings of two-dimensional bilayer gallium selenide crystals

DOE PAGES

Li, Xufan; Basile Carrasco, Leonardo A.; Yoon, Mina; ...

2015-01-21

Characterizing and controlling the interlayer orientations and stacking order of bilayer two-dimensional (2D) crystals and van der Waals (vdW) heterostructure is crucial to optimize their electrical and optoelectronic properties. The four polymorphs of layered gallium selenide (GaSe) that result from different layer stacking provide an ideal platform to study the stacking configurations in bilayer 2D crystals. Here, through a controllable vapor-phase deposition method we selectively grow bilayer GaSe crystals and investigate their two preferred 0° or 60° interlayer rotations. The commensurate stacking configurations (AA' and AB-stacking) in as-grown 2D bilayer GaSe crystals are clearly observed at the atomic scale andmore » the Ga-terminated edge structure are identified for the first time by using atomic-resolution scanning transmission electron microscopy (STEM). Theoretical analysis of the interlayer coupling energetics vs. interlayer rotation angle reveals that the experimentally-observed orientations are energetically preferred among the bilayer GaSe crystal polytypes. Here, the combined experimental and theoretical characterization of the GaSe bilayers afforded by these growth studies provide a pathway to reveal the atomistic relationships in interlayer orientations responsible for the electronic and optical properties of bilayer 2D crystals and vdW heterostructures.« less

Texture and elastic anisotropy of a mylonitic anorthosite from the Morin Shear Zone (Quebec, Canada)

NASA Astrophysics Data System (ADS)

Gómez Barreiro, Juan; Wenk, Hans-Rudolf; Vogel, Sven

2015-02-01

A sample of anorthosite from the granulite facies Morin Shear Zone (Quebec, Canada) was investigated for crystal preferred orientation and elastic anisotropy. Time-of-flight neutron diffraction data obtained with the HIPPO diffractometer at LANSCE were analyzed with the Rietveld method to obtain orientation distribution functions of the principal phases (plagioclase, clinopyroxene and orthopyroxene). Texture and microstructures are compatible with the plastic deformation of the aggregate under high-T conditions. All mineral phases depict a significant preferred orientation that could be related to the general top-to-the north shearing history of the Morin Shear Zone. Texture patterns suggest that (010)[001] in plagioclase and (110)[001] in clinopyroxene are likely dominant slip systems. Using preferred orientation data P- and S-waves velocities and elastic anisotropy were calculated and compared with previous studies to explore elastic properties of rocks with different pyroxene-plagioclase mixtures. P-wave velocity, S-wave splitting and anisotropy increase with clinopyroxene content. Seismic anisotropy is linked to the texture symmetry which can lead to large deviations between actual anisotropy and that measured along Cartesian XYZ sample directions (lineation/foliation reference frame). This is significant for the prediction and interpretation of seismic data, particularly for monoclinic or triclinic texture symmetries.

The Impact of Theoretical Orientation and Training on Preference for Diagnostic Models of Personality Pathology.

PubMed

Paggeot, Amy; Nelson, Sharon; Huprich, Steven

2017-01-01

The role of theoretical orientation in determining preference for different methods of diagnosis has been largely unexplored. The goal of the present study was to explore ratings of the usefulness of 4 diagnostic methods after applying them to a patient: prototype ratings derived from the SWAP-II, the DSM-5 Section III specific personality disorders, the DSM-5 Section III trait model, and prototype ratings derived from the Psychodynamic Diagnostic Manual (PDM). Three hundred and twenty-nine trainees in APA-accredited doctoral programs and internships rated one of their current patients with each of the 4 diagnostic methods. Individuals who classified their theoretical orientation as "cognitive- behavioral" displayed a significantly greater preference for the proposed DSM-5 personality disorder prototypes when compared to individuals who classified their orientation as "psychodynamic/psychoanalytic," while individuals who considered themselves psychodynamic or psychoanalytic rated the PDM as significantly more useful than those who considered themselves cognitive-behavioral. Individuals who classified their graduate program as a PsyD program were also more likely to rate the DSM-5 Section III and PDM models as more useful diagnostic methods than individuals who classified their graduate program as a PhD program. Implications and future directions will be discussed. © 2017 S. Karger AG, Basel.

Social motivation and implicit theory of mind in children with autism spectrum disorder.

PubMed

Burnside, Kimberly; Wright, Kristyn; Poulin-Dubois, Diane

2017-11-01

According to the social motivation theory of autism, children who develop Autism Spectrum Disorder (ASD) have early deficits in social motivation, which is expressed by decreased attention to social information. These deficits are said to lead to impaired socio-cognitive development, such as theory of mind (ToM). There is little research focused on the relation between social motivation and ToM in this population. The goal of the present study was to investigate the link between one aspect of social motivation, social orienting, and ToM in preschoolers with ASD. It was expected that, in contrast to typically developing (TD) children, children with ASD would show impaired performance on tasks measuring social orienting and ToM. It was also expected that children's performance on the social orienting tasks would be correlated with their performance on the ToM task. A total of 17 children with ASD and 16 TD children participated in this study. Participants completed two social orienting tasks, a face preference task and a biological motion preference task, as well an implicit false belief task. Results reveal that TD children, but not children with ASD, exhibited social preference as measured by a preference for faces and biological motion. Furthermore, children with ASD tended to perform worse on the ToM task compared to their TD counterparts. Performance on the social motivation tasks and the ToM task tended to be related but only for the TD children. These findings suggest that ToM is multifaceted and that motivational deficits might have downstream effects even on implicit ToM. Autism Res 2017, 10: 1834-1844. © 2017 International Society for Autism Research, Wiley Periodicals, Inc. The goal of the present study was to examine the link between poor attention to social information and mindreading abilities in children with autism spectrum disorder (ASD). Results demonstrated that children with ASD tended to perform worse than neurotypical children on both social orienting and theory of mind tasks. Preference for human faces and motion tended to be related but only for the neurotypical children. These findings provide partial support for the social motivation theory. © 2017 International Society for Autism Research, Wiley Periodicals, Inc.

Modeling agent's preferences by its designer's social value orientation

NASA Astrophysics Data System (ADS)

Zuckerman, Inon; Cheng, Kan-Leung; Nau, Dana S.

2018-03-01

Human social preferences have been shown to play an important role in many areas of decision-making. There is evidence from the social science literature that human preferences in interpersonal interactions depend partly on a measurable personality trait called, Social Value Orientation (SVO). Automated agents are often written by humans to serve as their delegates when interacting with other agents. Thus, one might expect an agent's behaviour to be influenced by the SVO of its human designer. With that in mind, we present the following: first, we explore, discuss and provide a solution to the question of how SVO tests that were designed for humans can be used to evaluate agents' social preferences. Second, we show that in our example domain there is a medium-high positive correlation between the social preferences of agents and their human designers. Third, we exemplify how the SVO information of the designer can be used to improve the performance of some other agents playing against those agents, and lastly, we develop and exemplify the behavioural signature SVO model which allows us to better predict performances when interactions are repeated and behaviour is adapted.

Temperament and self-based correlates of cooperative, competitive and individualistic learning preferences.

PubMed

Gocłowska, Małgorzata A; Aldhobaiban, Nawal; Elliot, Andrew J; Murayama, Kou; Kobeisy, Ahmed; Abdelaziz, Ashraf

2017-06-01

People vary in the extent to which they prefer cooperative, competitive or individualistic achievement tasks. In this research, we conducted two studies designed to investigate correlates and possible roots of these social interdependence orientations, namely approach and avoidance temperament, general self-efficacy, implicit theories of intelligence, and contingencies of self-worth based in others' approval, competition and academic competence. The results indicated that approach temperament, general self-efficacy and incremental theory were positively related, and entity theory was negatively related to cooperative preferences (|r| range from .11 to .41); approach temperament, general self-efficacy, competition contingencies and academic competence contingencies were positively related to competitive preferences (|r| range from .16 to .46); and avoidance temperament, entity theory, competitive contingencies and academic competence contingencies were positively related, and incremental theory was negatively related to individualistic preferences (|r| range from .09 to .15). The findings are discussed with regard to the meaning of each of the three social interdependence orientations, cultural differences among the observed relations and implications for practitioners. © 2015 International Union of Psychological Science.

40 CFR 421.290 - Applicability: Description of the secondary tin subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... secondary tin subcategory. 421.290 Section 421.290 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Tin Subcategory § 421.290 Applicability: Description of the secondary tin subcategory. The provisions of this subpart are applicable to discharges resulting from the production of tin at secondary tin...

40 CFR 421.290 - Applicability: Description of the secondary tin subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... secondary tin subcategory. 421.290 Section 421.290 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Tin Subcategory § 421.290 Applicability: Description of the secondary tin subcategory. The provisions of this subpart are applicable to discharges resulting from the production of tin at secondary tin...

40 CFR 421.290 - Applicability: Description of the secondary tin subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... secondary tin subcategory. 421.290 Section 421.290 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Tin Subcategory § 421.290 Applicability: Description of the secondary tin subcategory. The provisions of this subpart are applicable to discharges resulting from the production of tin at secondary tin...

40 CFR 421.290 - Applicability: Description of the secondary tin subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... secondary tin subcategory. 421.290 Section 421.290 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Tin Subcategory § 421.290 Applicability: Description of the secondary tin subcategory. The provisions of this subpart are applicable to discharges resulting from the production of tin at secondary tin...

40 CFR 421.290 - Applicability: Description of the secondary tin subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... secondary tin subcategory. 421.290 Section 421.290 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Tin Subcategory § 421.290 Applicability: Description of the secondary tin subcategory. The provisions of this subpart are applicable to discharges resulting from the production of tin at secondary tin...

Magnetic and clast fabrics as measurements of grain-scale processes within the Death Valley shallow crustal detachment faults

NASA Astrophysics Data System (ADS)

Hayman, Nicholas W.; Housen, B. A.; Cladouhos, T. T.; Livi, K.

2004-05-01

The rock product of shallow-crustal faulting includes fine-grained breccia and clay-rich gouge. Many gouges and breccias have a fabric produced by distributed deformation. The orientation of fabric elements provides constraints on the kinematics of fault slip and is the structural record of intrafault strain not accommodated by planar and penetrative surfaces. However, it can be difficult to quantify the deformational fabric of fault rocks, especially the preferred orientations of fine-grained minerals, or to uniquely determine the relationship between fabric geometry and finite strain. Here, we present the results of a fabric study of gouge and breccia sampled from low-angle normal (detachment) faults in the Black Mountains, Death Valley, CA. We measured a preferred orientation of the long axes of the clasts inherited from the crystalline footwall of the fault and compared the shape preferred orientation to the anisotropy of magnetic susceptibility of the fault rocks. The two measurements of fabric exhibit systematic similarities and differences in orientation and anisotropy that are compatible with the large-scale kinematics of fault slip. The dominant carriers of the magnetic susceptibility are micron- and sub-micron scale iron oxides and clay minerals. Therefore even the finest grains in the fault rock were sensitive to the distributed deformation and the micro-mechanics of particle interaction must have departed from those assumed by the passive-marker kinematic model that best explains the fabric.

Lattice-Preferred Orientation in Deformed Novaculite - Comparison of in-situ Results Using BEARTEX and Post-Mortem EBSD Analyses

NASA Astrophysics Data System (ADS)

Willenweber, A.; Thomas, S.; Burnley, P. C.

2012-12-01

The Berkeley Texture Package BEARTEX is a Windows-based computer software that combines various algorithms to analyze lattice-preferred orientation in polycrystalline materials. BEARTEX was initially designed to interpret diffraction intensity data from pole figure goniometers. Recently it has been successfully used to process synthetic forsterite powder diffraction data from in-situ synchrotron X-ray diffraction taken during deformation (Bollinger et al. 2012). Our study aims to test the practicability of using BEARTEX to analyze the evolution of lattice-preferred orientation in natural polycrystalline quartz (novaculite) during deformation. In-situ X-ray diffraction data was collected during the deformation of novaculite at 2.5 GPa and up to 1000 °C in a D-DIA apparatus using the ten-element energy-dispersive detector at the NSLS beamline X17B2. Diffraction intensities are a function of crystal orientation, expressed in azimuth angle η and pole distance ψ. The latter is the angle between the normal of a given diffraction plane and the vertical direction of the D-DIA apparatus - our principal stress direction during compression. Orientation-dependent diffraction intensities were corrected for different responses of the single detectors and x-ray absorption effects of the anvils. Orientation distributions (ODs) and inverse pole figures were calculated using BEARTEX. In addition, electron backscatter diffraction (EBSD) analyses were carried out on the deformed novaculite samples. Generated pole figures were compared with those derived from BEARTEX. Textural properties of our novaculite starting material complicated the BEARTEX analyses. The relatively strong variation of grain sizes in our natural specimens caused non-random diffraction intensity distributions. Those lead to non-random distributions of crystal orientations when analyzed with BEARTEX, although pole figures from EBSD data clearly show random crystal orientations. In an attempt to solve this problem, we employed a scanning routine when recording in-situ synchrotron X-ray diffraction and so collected diffraction from multiple sample volumes rather than from one single spot. Here, we will present a comparison of pole figures derived from independent BEARTEX and EBSD analyses for a series of novaculite experiments and discuss the practicability of BEARTEX to analyze the evolution of lattice-preferred orientation in natural polycrystalline quartz. REFERENCES C. BOLLINGER, S. MERKEL AND P. RATERRON (2012): In situ quantitative analysis of stress and texture development in forsterite aggregates deformed at 6 GPa and 1373 K. J. Appl. Cryst., 45, 263-271.

Citizenship Orientations in a Divided Society: A Comparison of Three Groups of Israeli Junior-High Students--Secular Jews, Religious Jews, and Israeli Arabs

ERIC Educational Resources Information Center

Sabbagh, Clara; Resh, Nura

2014-01-01

This study identifies major preferences for combinations of rights and duties (henceforth, citizenship orientations), as reflected in the political worldview of Israeli junior-high school students. Two distinct orientations were found, termed here as "liberal" and "ethno-republican". In order to contextualize the examination of…

Measuring implicit gender-role orientation: the gender initial preference task.

PubMed

Stieger, Stefan; Burger, Christoph; Schiller, Franziska R; Schulze, Esther K; Voracek, Martin

2014-01-01

Individuals prefer their name letters over nonname letters, which is known as the name-letter effect (NLE). This research aimed to examine a possible NLE for gender-role orientation (GRO) by rating letters for their gender-typicality in an initial preference task (Gender-IPT). Indeed, a clear NLE appeared: Men rated their initials as more male-typical, whereas women rated them as more female-typical. The Gender-IPT showed good convergent validity with other direct and indirect (Gender Implicit Association Test) measures of GRO as well as predictive validity with sensation seeking and gender-typical everyday life behaviors. The Gender-IPT seems to be a useful and practical indirect measure to assess GRO in a short, convenient, and computer-independent way, complementing other indirect measures of GRO.

Orientation control of barium titanate films using metal oxide nanosheet layer

NASA Astrophysics Data System (ADS)

Uchida, Hiroshi; Oi, Tomotake; Noguchi, Keito; Moki, Shota; Kim, Jin Woon; Shima, Hiromi; Nishida, Ken; Kiguchi, Takanori; Akama, Akihiko; Konno, Toyohiko J.; Funakubo, Hiroshi

2016-10-01

In the present work, we aim to achieve the preferred crystal orientation of chemical solution deposition (CSD)-derived BaTiO3 films on ubiquitous Si wafers with the assistance of Ca2Nb3O10 nanosheet (ns-CN) template layers. The ns-CN on platinized Si (Pt/Si) substrates aligned the BaTiO3(100) plane to the substrate surface, because of the favorable lattice matching of the ns-CN (001) plane. The CSD process in air required a high crystallization temperature of 900 °C for the preferred crystal orientation of BaTiO3(100) because of the BaCO3 byproduct generated during the combustion reaction of the precursor gel. The processing in vacuum to remove CO2 species enhanced the crystal orientation even at the crystallization temperature of 800 °C, although it can generate oxygen vacancies (\\text{V}\\text{O}{} \\bullet \\bullet ) that cause distorted polarization behavior under an applied field higher than approximately 150 kV/cm. The relative dielectric constant (εr) of the (100)-oriented BaTiO3 film on the ns-CN-supported Pt/Si substrate (ns-CN/Pt/Si) was generally larger than that of the randomly oriented film on Pt/Si, depending on the degree of crystal orientation.

Comparative assessment of gastrointestinal irritant potency in man of tin(II) chloride and tin migrated from packaging.

PubMed

Boogaard, Peter J; Boisset, Michel; Blunden, Steve; Davies, Scot; Ong, Teng Jin; Taverne, Jean-Pierre

2003-12-01

Tin is present in low concentrations in most canned foods and beverages, the highest levels being found in products packaged in unlacquered or partially lacquered tinplate cans. A limited number of case-reports of acute gastrointestinal disorders after consumption of food containing 100-500 mg/kg tin have been reported, but these reports suffer many insufficiencies. Controlled clinical studies on acute effects of tin migrated from packaging suggest a threshold concentration for adverse effects (AEs) of >730 mg/kg. Two separate randomised, single-centre, double-blind, crossover studies, enabling comparison of the tolerability of tin added as tin(II) chloride at concentrations of <0.5, 161, 264 and 529 mg/kg in 250 ml tomato juice in 20 volunteers (Study 1) and tin migrated from packaging at concentrations of <0.5, 201 and 267 mg/kg in 250 ml tomato soup in 24 volunteers (Study 2) were carried out. Distribution studies were conducted to get insight in the acute AEs of low molecular weight (<1000 Da) tin species in the soluble fraction of food products. Results show that the chemical form of tin and not the elemental concentration per se determines the severity of AEs. A clear dose-response relationship was only observed when tin was added as tin(II) chloride in tomato juice. No clinically significant AEs were reported in Study 2 and comparison of the incidence of tin-related AEs showed no difference between the dose levels (including control). Tin species of low molecular weight in supernatant represented 31-32% of total tin in canned tomato soup versus 56-61% in juice freshly spiked with tin(II) chloride. Differences in the incidence of AEs following administration of tomato juice with 161 and 264 mg of tin per kg and tomato soup with 201 and 267 mg of tin per kg likely results from differences in the concentration of low molecular weight tin species and in the nature of tin complexes formed. The results of this work demonstrate that tin levels up to 267 mg/kg in canned food cause no AEs in healthy adults and support the currently proposed tin levels of 200 mg/kg and 250 mg/kg for canned beverages and canned foods, respectively, as safe levels for adults in the general population.

Grain orientations and grain boundaries in tungsten nonotendril fuzz grown under divertor-like conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parish, Chad M.; Wang, Kun; Doerner, Russel P.

2016-09-19

We grew nanotendril “fuzz” on tungsten via plasma exposure and performed transmission Kikuchi diffraction (tKD) in scanning electron microscopy of isolated nanotendrils. 900 °C, 10 23 He/m 2sec, 4 × 10 26 He/m 2 exposure of tungsten produced a deep and fully developed nanotendril mat. tKD of isolated nanotendrils indicated that there was no preferred crystallographic direction oriented along the long axes of the tendrils, and the grain boundary character showed slightly preferential orientations. In conclusion, tendril growth is sufficiently non-equilibrium to prevent any preference of growth direction to manifest measurably, and that new high-angle boundaries (with new grains andmore » grain-growth axes) nucleate randomly along the tendrils during growth.« less

Fundamental studies of tin whiskering in microelectronics finishes

NASA Astrophysics Data System (ADS)

Pinol, Lesly Agnes

Common electronics materials, such as tin, copper, steel, and brass, are ambient reactive under common use conditions, and as such are prone to corrosion. During the early 1940s, reports of failures due to electrical shorting of components caused by 'whisker' (i.e., filamentary surface protrusion) growth on many surface types---including the aforementioned metals---began to emerge. Lead alloying of tin (3--10% by weight, typically in the eutectic proportion) eliminated whiskering risk for decades, until the July 2006 adoption of the Restriction of Hazardous Substances (RoHS) directive was issued by the European Union. This directive, which has since been adopted by California and parts of China, severely restricted the use of lead (<1000 ppm) in all electrical and electronics equipment being placed on the EU market, imposing the need for developing reliable new "lead-free" alternatives to SnPb. In spite of the abundance of modern-day anecdotes chronicling whisker-related failures in satellites, nuclear power stations, missiles, pacemakers, and spacecraft navigation equipment, pure tin finishes are still increasingly being employed today, and the root cause(s) of tin whiskering remains elusive. This work describes a series of structured experiments exploring the fundamental relationships between the incidence of tin whiskering (as dependent variable) and numerous independent variables. These variables included deposition method (electroplating, electroless plating, template-based electrochemical synthesis, and various physical vapor deposition techniques, including resistive evaporation, electron beam evaporation, and sputtering), the inclusion of microparticles and organic contamination, the effects of sample geometry, and nanostructuring. Key findings pertain to correlations between sample geometry and whisker propensity, and also to the stress evolution across a series of 4"-diameter silicon wafers of varying thicknesses with respect to the degree of post-metallization whiskering. Regarding sample geometry, it was found that smaller, thinner substrates displayed a more rapid onset of whiskering immediately following metallization. Changes in wafer-level stress were not found to correlate with whiskering morphology (number, density, length) after 6 weeks of aging. This result points either to the irrelevance of macrostress in the substrate/film composite, or to a difference in whiskering mechanism for rigid substrates (whose stress gradient over time is significant) when compared with thinner, flexible substrates (whose stress is less variable with time). Organic contamination was found to have no appreciable effect when explicitly introduced. Furthermore, electron-beam evaporated films whiskered more readily than films deposited via electroplating from baths containing organic "brighteners." Beyond such findings, novel in themselves, our work is also unique in that we emphasize the "clean" deposition of tin (with chromium adhesion layers and copper underlayers) by vacuum-based physical vapor deposition, to circumvent the question of contamination entirely. By employing silicon substrates exclusively, we have distinguished ourselves from other works (which, for example, use copper coupons fabricated from rolled shim stock) because we have better sample-to-sample consistency in terms of material properties, machinability, and orientation.

Heart rate variability is associated with social value orientation in males but not females.

PubMed

Lischke, Alexander; Mau-Moeller, Anett; Jacksteit, Robert; Pahnke, Rike; Hamm, Alfons O; Weippert, Matthias

2018-05-09

Phylogenetic and neurobiological theories suggest that inter-individual differences in high frequency heart rate variability (HF-HRV) are associated with inter-individual differences in social behavior and social cognition. To test these theories, we investigated whether individuals with high and low HF-HRV would show different preferences for cooperative behavior in social contexts. We recorded resting state HF-HRV in 84 healthy individuals before they completed the Social Value Orientation task, a well-established measure of cooperative preferences. HF-HRV was derived from short-term (300 s) and ultra-short-term (60 s, 120 s) recordings of participants' heart rate to determine the robustness of possible findings. Irrespective of recording length, we found a sex-dependent association between inter-individual differences in HF-HRV and inter-individual differences in social value orientation: The preference for cooperation was more pronounced among individuals with high as compared low HF-HRV, albeit only in male and not in female participants. These findings suggest that males with high HF-HRV are more inclined to engage in cooperative behavior than males with low HF-HRV.

Correlation between crystallographic anisotropy and dendritic orientation selection of binary magnesium alloys.

PubMed

Du, Jinglian; Guo, Zhipeng; Zhang, Ang; Yang, Manhong; Li, Mei; Xiong, Shoumei

2017-10-19

Both synchrotron X-ray tomography and EBSD characterization revealed that the preferred growth directions of magnesium alloy dendrite change as the type and amount of solute elements. Such growth behavior was further investigated by evaluating the orientation-dependent surface energy and the subsequent crystallographic anisotropy via ab-initio calculations based on density functional theory and hcp lattice structure. It was found that for most binary magnesium alloys, the preferred growth direction of the α-Mg dendrite in the basal plane is always [Formula: see text], and independent on either the type or concentration of the additional elements. In non-basal planes, however, the preferred growth direction is highly dependent on the solute concentration. In particular, for Mg-Al alloys, this direction changes from [Formula: see text] to [Formula: see text] as the Al-concentration increased, and for Mg-Zn alloys, this direction changes from [Formula: see text] to [Formula: see text] or [Formula: see text] as the Zn-content varied. Our results provide a better understanding on the dendritic orientation selection and morphology transition of magnesium alloys at the atomic level.

Telomere dysfunction and cell survival: roles for distinctTIN2-containing complexes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Sahn-Ho; Davalos, Albert R.; Heo, Seok-Jin

Telomeres are maintained by three DNA binding proteins, TRF1, TRF2 and POT1, and several associated factors. One factor, TIN2, binds TRF1 and TRF2 directly and POT1 indirectly. These and two other proteins form a soluble complex that may be the core telomere-maintenance complex. It is not clear whether subcomplexes exist or function in vivo. Here, we provide evidence for two TIN2 subcomplexes with distinct functions in human cells. TIN2 ablation by RNA interference caused telomere uncapping and p53-independent cell death in all cells tested. However, we isolated two TIN2 complexes from cell lysates, each selectively sensitive to a TIN2 mutantmore » (TIN2-13, TIN2-15C). In cells with wild-type p53 function, TIN2-15C was more potent than TIN2-13 in causing telomere uncapping and eventual growth arrest. In cells lacking p53 function, TIN215C more than TIN2-13 caused genomic instability and cell death. Thus, TIN2 subcomplexes likely have distinct functions in telomere maintenance, and may provide selective targets for eliminating cells with mutant p53.« less

Tin

USGS Publications Warehouse

Kamilli, Robert J.; Kimball, Bryn E.; Carlin, James F.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

Tin (Sn) is one of the first metals to be used by humans. Almost without exception, tin is used as an alloy. Because of its hardening effect on copper, tin was used in bronze implements as early as 3500 B.C. The major uses of tin today are for cans and containers, construction materials, transportation materials, and solder. The predominant ore mineral of tin, by far, is cassiterite (SnO2).In 2015, the world’s total estimated mine production of tin was 289,000 metric tons of contained tin. Total world reserves at the end of 2016 were estimated to be 4,700,000 metric tons. China held about 24 percent of the world’s tin reserves and accounted for 38 percent of the world’s 2015 production of tin.The proportion of scrap used in tin production is between 10 and 25 percent. Unlike many metals, tin recycling is relatively efficient, and the fraction of tin in discarded products that get recycled is greater than 50 percent.Only about 20 percent of the world’s identified tin resources occur as primary hydrothermal hard-rock veins, or lodes. These lodes contain predominantly high-temperature minerals and almost invariably occur in close association with silicic, peraluminous granites. About 80 percent of the world’s identified tin resources occur as unconsolidated secondary or placer deposits in riverbeds and valleys or on the sea floor. The largest concentration of both onshore and offshore placers is in the extensive tin belt of Southeast Asia, which stretches from China in the north, through Thailand, Burma (also referred to as Myanmar), and Malaysia, to the islands of Indonesia in the south. Furthermore, tin placers are almost always found closely allied to the granites from which they originate. Other countries with significant tin resources are Australia, Bolivia, and Brazil.Most hydrothermal tin deposits belong to what can be thought of as a superclass of porphyry-greisen deposits. The hydrothermal tin deposits are all characterized by a close spatial, temporal, and genetic association with highly differentiated, peraluminous porphyritic granite intrusions. The intrusions form pegmatites; disseminated ore; parallel or subparallel, greisen-bordered sheeted veins that either cross-cut the intrusion or are peripheral to it; skarns; and (or) limestone replacements that contain different amounts of cassiterite, molybdenite, and wolframite.The tectonic settings of tin-bearing granites are relatively well understood and of limited variety. Tin and tungsten deposits and their associated igneous rocks are found mainly in continental settings.Historically, prospecting for tin has been carried out by the time-honored methods of panning, drilling, trenching, and assaying. Geophysical and geochemical surveys have been employed to cover large areas more rapidly, isolating areas of possible tin deposits so that drilling can be more effective and less costly. Elemental concentrations and relationships of the lithophile elements, especially barium, lithium, niobium, potassium, rubidium, and zirconium, are the most reliable chemical indicators of ore-forming processes and tin-bearing potential.The average human diet includes an intake of about 10 milligrams per day of tin. Ingestion of tin in significantly greater amounts than 10 milligrams per day may lead to a stomach ache, anemia, and liver and kidney problems. Exposure to some organo-tin compounds can interfere with brain and nervous system function and, in severe cases, can cause death. Extended inhalation of tin oxide—an issue mainly for those people who work in the tin industry—results in a higher potential to develop stannosis, which is a mild disease of the lungs caused by the inhalation of tin-bearing dust. Inorganic tin is poorly absorbed by the body, and no evidence exists for the carcinogenicity of metallic tin and tin compounds in humans.Most placer tin deposits are mined by open pit and (or) dredging methods. Mining of alluvial placers in modern streambeds and riverbeds is likely to increase the amount of sediment delivered downstream. This, combined with potential diversion of rivers and streams, may negatively affect downstream ecosystems. Many of the placer deposits located in Burma, Indonesia, Malaysia, and Thailand are located offshore. Most offshore placer tin deposits are mined by dredging methods, which have the potential to negatively affect benthic, midwater, and pelagic ecosystems.In a congressionally mandated U.S. Department of Defense study of strategic minerals published in 2013, tin has the greatest shortfall amount (insufficient supply to meet demand) at \\$416 million; this amount is more than twice that of antimony ($182 million), which is the strategic mineral with the next largest shortfall amount (U.S. Department of Defense, 2013). The United States imported 75 percent of its tin supply in 2015. During the period 2012–15, these imports were from, in descending order of amount imported, Peru, Indonesia, Malaysia, and Bolivia.A promising advancement concerning research into the origin of tin deposits is the recent development of a reliable method of analyzing tin isotopes in cassiterite. Although the mechanism of transport and deposition of tin is fairly well understood, the means by which tin is incorporated into the parent magma at the points of magma generation and ascent needs further investigation.Tin metallogenic provinces worldwide are well known. Consequently, any undiscovered tin deposits will likely be spatially close to known deposits or extensions of the same.

[Patient orientation and reference to the ICF as challenges in outcome assessment in rehabilitation].

PubMed

Farin, E

2008-04-01

Measuring the results of rehabilitation interventions presents a number of issues regarding content and method, two of which have been selected for discussion in view of the findings of current research--the significance of patient orientation and the relation to the International Classification of Functioning, Disability and Health, ICF. Compilation of patients' treatment goals, expectations and preferences, patient participation in the development of assessment instruments, compilation of patients' evaluations of treatment results and consideration of the subjectivity of the physician as well as interaction between patient and physician were discussed with respect to involving patients in measuring results. The ICF is a terminology system presenting a uniform international classification for describing health conditions that could assume the function of a common language for the members of various occupations involved in medical rehabilitation. Orienting the measurement of results to the ICF is an obvious next step. This can promote patient orientation, as the categories used by the ICF--in particular for the domains of activities and participation--are formulated in terms relevant to daily routine and are thus pertinent to the patients' lifestyle. The consequences resulting from this overview concern future research needs on the one hand, and on the other hand tips for carrying out a patient-oriented, ICF-based measurement of results. The need for research becomes especially clear regarding the measurement of results based on patient preferences, the determination of the participation relevance perceived by the patient as a criterion for "patient significance" (analogous to "clinical significance"), the integration and weighting of patient and physician assessments of success, the consideration of physicians' subjective concepts and patients' communication preferences, and the design of new, ICF-oriented assessment instruments.

Hollow tin/chromium whiskers

NASA Astrophysics Data System (ADS)

Cheng, Jing; Vianco, Paul T.; Li, James C. M.

2010-05-01

Tin whiskers have been an engineering challenge for over five decades. The mechanism has not been agreed upon thus far. This experiment aimed to identify a mechanism by applying compressive stresses to a tin film evaporated on silicon substrate with an adhesion layer of chromium in between. A phenomenon was observed in which hollow whiskers grew inside depleted areas. Using focused ion beam, the hollow whiskers were found to contain both tin and chromium. At the bottom of the depleted areas, thin tin/tin oxide film remained over the chromium layer. It indicates that tin transport occurred along the interface between tin and chromium layers.

Vocational Preferences of Daughters of Alcoholics

ERIC Educational Resources Information Center

Gade, Eldon M.; Goodman, Ronald E.

1975-01-01

This study was designed to examine the vocational interests of daughters of alcoholics. Mixed support was provided for the assumption that their vocational choices are nonperson oriented. Data did support the prediction of high scores on the realistic and intellectual scales of Holland's Vocational Preference Inventory. (SJL)

Are personal values of importance in the stigmatization of people with mental illness?

PubMed

Norman, Ross Mg; Sorrentino, Richard; Windell, Deborah; Manchanda, Rahul

2008-12-01

To investigate the relation of responses to the Schwartz Value Scale to preferred social distance to a person with either schizophrenia or depression. The influence of personal value priorities on discrimination has been investigated in several contexts, but seldom with reference to social distance towards those with mental illness. University students (n = 200) completed the Schwartz Value Scale, as well as a measure of beliefs about mental illness and preferred social distance with reference to a vignette describing a person with either schizophrenia or depression. Consistent with past findings, respondents indicated a preference for greater social distance for schizophrenia than depression, and beliefs about likelihood of socially inappropriate behaviour and danger were correlated with social distance. Self-transcendence value orientation was a significant independent predictor of preference for less social distance. These findings were not influenced by a social desirability bias. Value orientation makes a significant contribution to the prediction of social distance towards those with mental illness. Evaluation of value-based interventions to reduce such discrimination appears warranted.

Peroxide induced tin oxide coating of graphene oxide at room temperature and its application for lithium ion batteries.

PubMed

Sladkevich, S; Gun, J; Prikhodchenko, P V; Gutkin, V; Mikhaylov, A A; Novotortsev, V M; Zhu, J X; Yang, D; Hng, H H; Tay, Y Y; Tsakadze, Z; Lev, O

2012-12-07

We describe a new, simple and low-temperature method for ultra-thin coating of graphene oxide (GO) by peroxostannate, tin oxide or a mixture of tin and tin oxide crystallites by different treatments. The technique is environmentally friendly and does not require complicated infrastructure, an autoclave or a microwave. The supported peroxostannate phase is partially converted after drying to crystalline tin oxide with average, 2.5 nm cassiterite crystals. Mild heat treatment yielded full coverage of the reduced graphene oxide by crystalline tin oxide. Extensive heat treatment in vacuum at >500 °C yielded a mixture of elemental tin and cassiterite tin oxide nanoparticles supported on reduced graphene oxide (rGO). The usefulness of the new approach was demonstrated by the preparation of two types of lithium ion anodes: tin oxide-rGO and a mixture of tin oxide and tin coated rGO composites (SnO(2)-Sn-rGO). The electrodes exhibited stable charge/discharge cyclability and high charging capacity due to the intimate contact between the conductive graphene and the very small tin oxide crystallites. The charging/discharging capacity of the anodes exceeded the theoretical capacity predicted based on tin lithiation. The tin oxide coated rGO exhibited higher charging capacity but somewhat lower stability upon extended charge/discharge cycling compared to SnO(2)-Sn-rGO.

Large magnetoresistance in a directionally solidified Ni44.5Co5.1Mn37.1In13.3 magnetic shape memory alloy

NASA Astrophysics Data System (ADS)

Li, Zongbin; Hu, Wei; Chen, Fenghua; Zhang, Mingang; Li, Zhenzhuang; Yang, Bo; Zhao, Xiang; Zuo, Liang

2018-04-01

Polycrystalline Ni44.5Co5.1Mn37.1In13.3 alloy with coarse columnar-shaped grains and 〈0 0 1〉A preferred orientation was prepared by directional solidification. Due to the strong magnetostructural coupling, inverse martensitic transformation can be induced by the magnetic field, resulting in large negative magnetoresistance up to -58% under the field of 3 T. Such significant field controlled functional behaviors should be attributed to the coarse grains and strong preferred orientation in the directionally solidified alloy.

Catalytic growth of vertically aligned SnS/SnS2 p-n heterojunctions

NASA Astrophysics Data System (ADS)

Degrauw, Aaron; Armstrong, Rebekka; Rahman, Ajara A.; Ogle, Jonathan; Whittaker-Brooks, Luisa

2017-09-01

Nanowire arrays of SnS/SnS2 p-n heterojunctions are grown on transparent indium tin oxide (ITO) coated-glass and Si/SiO2 substrates via chemical vapor transport (CVT). The nanowire arrays are comprised of individual SnS/SnS2 heterostructures that are highly oriented with their lengths and morphologies controlled by the CVT conditions (i.e. reaction temperature, flow rate, and reaction time). The growth and optoelectronic characterization of these well-defined SnS/SnS2 p-n heterostructures pave the way for the fabrication of highly efficient solar cell devices.

Development of Maps of Simple and Complex Cells in the Primary Visual Cortex

PubMed Central

Antolík, Ján; Bednar, James A.

2011-01-01

Hubel and Wiesel (1962) classified primary visual cortex (V1) neurons as either simple, with responses modulated by the spatial phase of a sine grating, or complex, i.e., largely phase invariant. Much progress has been made in understanding how simple-cells develop, and there are now detailed computational models establishing how they can form topographic maps ordered by orientation preference. There are also models of how complex cells can develop using outputs from simple cells with different phase preferences, but no model of how a topographic orientation map of complex cells could be formed based on the actual connectivity patterns found in V1. Addressing this question is important, because the majority of existing developmental models of simple-cell maps group neurons selective to similar spatial phases together, which is contrary to experimental evidence, and makes it difficult to construct complex cells. Overcoming this limitation is not trivial, because mechanisms responsible for map development drive receptive fields (RF) of nearby neurons to be highly correlated, while co-oriented RFs of opposite phases are anti-correlated. In this work, we model V1 as two topographically organized sheets representing cortical layer 4 and 2/3. Only layer 4 receives direct thalamic input. Both sheets are connected with narrow feed-forward and feedback connectivity. Only layer 2/3 contains strong long-range lateral connectivity, in line with current anatomical findings. Initially all weights in the model are random, and each is modified via a Hebbian learning rule. The model develops smooth, matching, orientation preference maps in both sheets. Layer 4 units become simple cells, with phase preference arranged randomly, while those in layer 2/3 are primarily complex cells. To our knowledge this model is the first explaining how simple cells can develop with random phase preference, and how maps of complex cells can develop, using only realistic patterns of connectivity. PMID:21559067

Telomere dysfunction and cell survival: Roles for distinct TIN2-containing complexes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Sahn-ho; Davalos, Albert R.; Heo, Seok-Jin

Telomeres are maintained by three DNA binding proteins (TRF1, TRF2 and POT1), and several associated factors. One factor, TIN2, binds TRF1 and TRF2 directly and POT1 indirectly. Along with two other proteins, TPP1 and hRap1, these form a soluble complex that may be the core telomere maintenance complex. It is not clear whether sub-complexes also exist in vivo. We provide evidence for two TIN2 sub-complexes with distinct functions in human cells. We isolated these two TIN2 sub-complexes from nuclear lysates of unperturbed cells and cells expressing TIN2 mutants TIN2-13, TIN2-15C, which cannot bind TRF2 or TRF1, respectively. In cells withmore » wild-type p53 function, TIN2-15C was more potent than TIN2-13 in causing telomere uncapping and eventual growth arrest. In cells lacking p53 function, TIN2-15C was more potent than TIN2-13 in causing telomere dysfunction and cell death. Our findings suggest that distinct TIN2 complexes exist, and that TIN2-15C-sensitive subcomplexes are particularly important for cell survival in the absence of functional p53.« less

Attention-Orienting and Attention-Holding Effects of Faces on 4- to 8-Month-Old Infants

ERIC Educational Resources Information Center

DeNicola, Christopher A.; Holt, Nicholas A.; Lambert, Amy J.; Cashon, Cara H.

2013-01-01

Attention-orienting and attention-holding effects of faces were investigated in a sample of 64 children, aged 4 to 8 months old. A visual preference task was used, in which pairs of faces and toys were presented in eight 10-second trials. Effects of age and sitting-ability were examined. Attention-orienting toward faces was measured using the…

Link between orientation and retinotopic maps in primary visual cortex

PubMed Central

Paik, Se-Bum; Ringach, Dario L.

2012-01-01

Maps representing the preference of neurons for the location and orientation of a stimulus on the visual field are a hallmark of primary visual cortex. It is not yet known how these maps develop and what function they play in visual processing. One hypothesis postulates that orientation maps are initially seeded by the spatial interference of ON- and OFF-center retinal receptive field mosaics. Here we show that such a mechanism predicts a link between the layout of orientation preferences around singularities of different signs and the cardinal axes of the retinotopic map. Moreover, we confirm the predicted relationship holds in tree shrew primary visual cortex. These findings provide additional support for the notion that spatially structured input from the retina may provide a blueprint for the early development of cortical maps and receptive fields. More broadly, it raises the possibility that spatially structured input from the periphery may shape the organization of primary sensory cortex of other modalities as well. PMID:22509015

Adolescent trust and trustworthiness: role of gender and social value orientation.

PubMed

Derks, Jeffrey; Lee, Nikki C; Krabbendam, Lydia

2014-12-01

Trusting others is an essential feature of adolescent development. The aim of this study was to investigate gender differences in trusting behavior using an experimental game and relate these to the underlying social preferences. 206 adolescents (Mage = 15.1 years, 51% girls) performed a series of one-shot Trust Games to measure their levels of trust and trustworthiness. Social value orientation, or the preference to maximize one's own outcomes (proself) or both the outcomes of self and other (prosocial) was assessed using the Triple Dominance Measure. Boys were more trusting than girls, but no gender differences on trustworthiness were found. Prosocials were more trusting and trustworthy than proselfs. In addition, gender and social value orientation were independent predictors of trust (but not trustworthiness). These findings show that the higher levels of trust in boys are not the result of a gender difference in prosocial orientation. Copyright © 2014 The Foundation for Professionals in Services for Adolescents. Published by Elsevier Ltd. All rights reserved.

The solvation structures of cellulose microfibrils in ionic liquids.

PubMed

Mostofian, Barmak; Smith, Jeremy C; Cheng, Xiaolin

2011-12-01

The use of ionic liquids for non-derivatized cellulose dissolution promises an alternative method for the thermochemical pretreatment of biomass that may be more efficient and environmentally acceptable than more conventional techniques in aqueous solution. Here, we performed equilibrium MD simulations of a cellulose microfibril in the ionic liquid 1-butyl-3-methylimidazolium chloride (BmimCl) and compared the solute structure and the solute-solvent interactions at the interface with those from corresponding simulations in water. The results indicate a higher occurrence of solvent-exposed orientations of cellulose surface hydroxymethyl groups in BmimCl than in water. Moreover, spatial and radial distribution functions indicate that hydrophilic surfaces are a preferred site of interaction between cellulose and the ionic liquid. In particular, hydroxymethyl groups on the hydrophilic fiber surface adopt a different conformation from their counterparts oriented towards the fiber's core. Furthermore, the glucose units with these solvent-oriented hydroxymethyls are surrounded by the heterocyclic organic cation in a preferred parallel orientation, suggesting a direct and distinct interaction scheme between cellulose and BmimCl.

Development of a Distributed Hydrologic Model Using Triangulated Irregular Networks for Continuous, Real-Time Flood Forecasting

NASA Astrophysics Data System (ADS)

Ivanov, V. Y.; Vivoni, E. R.; Bras, R. L.; Entekhabi, D.

2001-05-01

The Triangulated Irregular Networks (TINs) are widespread in many finite-element modeling applications stressing high spatial non-uniformity while describing the domain of interest in an optimized fashion that results in superior computational efficiency. TINs, being adaptive to the complexity of any terrain, are capable of maintaining topological relations between critical surface features and therefore afford higher flexibility in data manipulation. The TIN-based Real-time Integrated Basin Simulator (tRIBS) is a distributed hydrologic model that utilizes the mesh architecture and the software environment developed for the CHILD landscape evolution model and employs the hydrologic routines of its raster-oriented version, RIBS. As a totally independent software unit, the tRIBS consolidates the strengths of the distributed approach and efficient computational data platform. The current version couples the unsaturated and the saturated zones and accounts for the interaction of moving infiltration fronts with a variable groundwater surface, allowing the model to handle both storm and interstorm periods in a continuous fashion. Recent model enhancements have included the development of interstorm hydrologic fluxes through an evapotranspiration scheme as well as incorporation of a rainfall interception module. Overall, the tRIBS model has proven to properly mimic successive phases of the distributed catchment response by reproducing various runoff production mechanisms and handling their meteorological constraints. Important improvements in modeling options, robustness to data availability and overall design flexibility have also been accomplished. The current efforts are focused on further model developments as well as the application of the tRIBS to various watersheds.

Relating Teachers' Whistleblowing Tendency and Personal Features: Machiavellianism, Religiosity, and Utilitarianism

ERIC Educational Resources Information Center

Gökçe, Asiye Toker

2015-01-01

This study examines relationships between religiosity and value orientation of teachers, and preference for whistleblowing modes. Three hypotheses were developed, and tested related to the relationships between utilitarianism, religiosity, Machiavellianism and preference for various forms of whistleblowing. To analyse the data obtained from a…

Leadership Preferences of Indian and Non-Indian Athletes.

ERIC Educational Resources Information Center

Malloy, D. C.; Nilson, R. N.

1991-01-01

Among 86 Indian and non-Indian volleyball competitors, non-Indian players indicated significantly greater preferences for leadership that involved democratic behavior, autocratic behavior, or social support. Indians may adapt their behavior by participating in non-Indian games, without changing their traditional value orientations. Contains 22…

Strategies to Reduce Tin and Other Metals in Electronic Cigarette Aerosol

PubMed Central

Williams, Monique; To, An; Bozhilov, Krassimir; Talbot, Prue

2015-01-01

Background Metals are present in electronic cigarette (EC) fluid and aerosol and may present health risks to users. Objective The objective of this study was to measure the amounts of tin, copper, zinc, silver, nickel and chromium in the aerosol from four brands of EC and to identify the sources of these metals by examining the elemental composition of the atomizer components. Methods Four brands of popular EC were dissected and the cartomizers were examined microscopically. Elemental composition of cartomizer components was determined using integrated energy dispersive X-ray microanalysis, and the concentrations of the tin, copper, zinc silver, nickel, and chromium in the aerosol were determined for each brand using inductively coupled plasma optical emission spectroscopy. Results All filaments were made of nickel and chromium. Thick wires were copper coated with either tin or silver. Wires were joined to each other by tin solder, brazing, or by brass clamps. High concentrations of tin were detected in the aerosol when tin solder joints were friable. Tin coating on copper wires also contributed to tin in the aerosol. Conclusions Tin concentrations in EC aerosols varied both within and between brands. Tin in aerosol was reduced by coating the thick wire with silver rather than tin, placing stable tin solder joints outside the atomizing chamber, joining wires with brass clamps or by brazing rather than soldering wires. These data demonstrate the feasibility of removing tin and other unwanted metals from EC aerosol by altering designs and using materials of suitable quality. PMID:26406602

Preferred orientation in experimentally deformed stishovite: implications for deformation mechanisms

DOE PAGES

Kaercher, Pamela M.; Zepeda-Alarcon, Eloisa; Prakapenka, Vitali B.; ...

2014-11-07

Although the crystal structure of the high pressure SiO 2 polymorph stishovite has been studied in detail, little is known about the development of crystallographic preferred orientation (CPO) during deformation in stishovite. Insight into CPO and associated deformation mechanics of stishovite would provide important information for understanding subduction of quartz-bearing crustal rocks into the mantle. To study CPO development, we converted a natural sample of flint to stishovite in a laser heated diamond anvil cell and compressed the stishovite aggregate up to 38 GPa. We collected diffraction patterns in radial geometry to examine in situ development of crystallographic preferred orientationmore » and find that (001) poles preferentially align with the compression direction. Viscoplastic self-consistent modeling suggests the most likely slip systems at high pressure and ambient temperature are pyramidal and basal slip.« less

Sexual orientation of male mouse offspring prenatally exposed to ethanol.

PubMed

Watabe, T; Endo, A

1994-01-01

Pregnant mice were intubated with either low (2 g/kg) or high (4 g/kg) dose of ethanol twice daily throughout the last third of the gestational period (from dg14 to dg18: gestational day; plug positive = dg 0). Ninety days after birth, the sexual orientation test was conducted on male offspring. This test was designed to observe a two-choice preference for either male or female partners in a setting in which the test animal could move freely between the two incentive compartments within which a stud male and an estrous female had been placed. We found that young adult males that had been exposed to ethanol prenatally have a decreased preference for the opposite sex and an increased preference for the same sex as a partner, although their physical development was apparently unaffected.

User-Centered Design and Printed Educational Materials: A Focus Group Study of Primary Care Physician Preferences.

PubMed

Grudniewicz, Agnes; Bhattacharyya, Onil; McKibbon, K Ann; Straus, Sharon E

2016-01-01

It is challenging for primary care physicians (PCPs) to review and apply the growing amount of clinical evidence available. Printed educational materials (PEMs), which synthesize evidence, are often ineffective at improving knowledge, possibly due to poor design and limited uptake. In this study, we collected PCP preferences for the design and content of physician-oriented PEMs and determined key attributes that may increase their usability and uptake. We held 90-minute focus groups with PCPs in Toronto, ON, Canada. Focus groups included discussion about whether and how participants use PEMs, feedback on three examples of PEMs, and a discussion on general format and design preferences in PEMs. We analyzed focus group transcripts using a thematic analysis and summarized results in a list of user preferences. Four focus groups were held with 13 PCPs. We found that participants only read PEMs relevant to their patients and prefer short, concise documents, with links to sources that can provide more detailed information. Simplicity of materials was important, with many participants preferring PEMs without lengthy backgrounds or scientific explanations. Most participants wanted to see key messages highlighted to easily assess the relevance of the materials to their practice. Some participants shared physician-oriented PEMs with patients. This study shows that PCPs may prefer shorter, simpler, and more concise documents that have less scientific detail but provide references to further information sources. It is important to understand end user preferences for the design and content of these materials to enhance their uptake.

Orientation dependence of ferroelectric and piezoelectric properties of Bi3.15Nd0.85Ti3O12 thin films on Pt(100)/TiO2/SiO2/Si substrates

NASA Astrophysics Data System (ADS)

Hu, G. D.

2006-11-01

Bi3.15Nd0.85Ti3O12 (BNT0.85) thin films with (100) [α(100)=87.8%], (117) [α(117)=77.1%], and (001) [α(001)=98.8%] preferred orientations were deposited on Pt(100)/TiO2/SiO2/Si substrates using a metal organic decomposition process. The remanent polarization of (100)-predominant BNT0.85 film is about 50% and three times larger than those of (117)-preferred and (001)-oriented films, respectively, suggesting that the major polarization vector of BNT0.85 is close to the a axis rather than the c axis. This result can be further demonstrated by the piezoelectric measurements using an atomic force microscope in the piezoresponse mode.

METHOD FOR JOINING ALUMINUM TO STAINLESS STEEL

DOEpatents

Lemon, L.C.

1960-05-24

Aluminum may be joined to stainless steel without the use of flux by tinning the aluminum with a tin solder containing 1% silver and 1% lead, tinning the stainless steel with a 50% lead 50% tin solder, and then sweating the tinned surfaces together.

Religious Belief and Practice: New Forces in American Politics?

ERIC Educational Resources Information Center

Beatty, Kathleen Murphy; Walter, Oliver

Exploratory research suggests that denominational preferences, fundamentalism, and church attendance are related to an individual's position on political issues. A review of research reveals that religious beliefs are stable, developed early in life, and are central to an individual's other orientations. Research on religious orientation is…

Graphoepitaxy by encapsulation

DOEpatents

Geis, Michael W.; Smith, Henry I.; Antoniadis, Dimitri A.; Flanders, Dale C.

1986-01-01

Improvements on the graphoepitaxial process for obtaining epitaxial or preferred orientation films are described wherein a cap of material is formed over the film to be oriented, artificial surface-relief structure may be present in the substrate, the cap, or both, and the film may be heated by irradiation with electromagnetic radiation.

Characterization of monoclinic crystals in tablets by pattern-fitting procedure using X-ray powder diffraction data.

PubMed

Yamamura, Shigeo; Momose, Yasunori

2003-06-18

The purpose of this study is to characterize the monoclinic crystals in tablets by using X-ray powder diffraction data and to evaluate the deformation feature of crystals during compression. The monoclinic crystals of acetaminophen and benzoic acid were used as the samples. The observed X-ray diffraction intensities were fitted to the analytic expression, and the fitting parameters, such as the lattice parameters, the peak-width parameters, the preferred orientation parameter and peak asymmetric parameter were optimized by a non-linear least-squares procedure. The Gauss and March distribution functions were used to correct the preferred orientation of crystallites in the tablet. The March function performed better in correcting the modification of diffraction intensity by preferred orientation of crystallites, suggesting that the crystallites in the tablets had fiber texture with axial orientation. Although a broadening of diffraction peaks was observed in acetaminophen tablets with an increase of compression pressure, little broadening was observed in the benzoic tablets. These results suggest that "acetaminophen is a material consolidating by fragmentation of crystalline particles and benzoic acid is a material consolidating by plastic deformation then occurred rearrangement of molecules during compression". A pattern-fitting procedure is the superior method for characterizing the crystalline drugs of monoclinic crystals in the tablets, as well as orthorhombic isoniazid and mannitol crystals reported in the previous paper.

Assessment of Attractiveness of Plants as Roosting Sites for the Melon Fly, Bactrocera cucurbitae, and Oriental Fruit Fly, Bactrocera dorsalis

PubMed Central

McQuate, Grant T.; Vargas, Roger I.

2007-01-01

The use of toxic protein bait sprays to suppress melon fly, Bactrocera cucurbitae (Coquillett) (Diptera: Tephritidae), populations typically involves application to vegetation bordering agricultural host areas where the adults seek shelter (“roost”). Although bait spray applications for suppression of oriental fruit fly, Bactrocera dorsalis (Hendel), populations have traditionally been applied to the host crop, rather than to crop borders, roosting by oriental fruit flies in borders of some crop species, such as papaya, Carica papaya L. (Brassicales: Caricaceae), suggests that bait spray applications to crop borders could also help in suppression of B. dorsalis populations. In order to develop improved recommendations for application of bait sprays to border plants for suppression of melon fly and oriental fruit fly populations, the relative attractiveness of a range of plant species, in a vegetative (non-flowering) stage, was tested to wild melon fly and oriental fruit fly populations established in a papaya orchard in Hawaii. A total of 20 plant species were evaluated, divided into four categories: 1) border plants, including corn, Zea mays L. (Poales: Poaceae), windbreaks and broad-leaved ornamentals, 7 species; 2) weed plants commonly found in agricultural fields in Hawaii, 6 species; 3) host crop plants, 1 species- zucchini, Cucurbita pepo L. (Violales: Curcurbitaceae), and 4) locally grown fruit trees, 6 species. Plants were established in pots and placed in an open field, in clusters encircling protein bait traps, 20 m away from the papaya orchard. Castor bean, Ricinus communis L. (Euphorbiales: Euphorbiaceae), panax, Polyscias guilfoylei (Bull) Bailey (Apiales: Araliaceae), tiger's claw, Erythnna variegata L. (Fabales: Fabaceae), and guava, Psidium guajava L. (Myrtales: Myrtaceae) were identified as preferred roosting hosts for the melon fly, and tiger's claw, panax, castor bean, Canada cocklebur, Xanthium strumarium L. (Asterales: Asteraceae), Brazilian pepper tree, Schinus terebinthifolius Raddi (Sapindales: Anacardiaceae), ti plant, Cordyline terminate (L.) Chev.(Liliales: Liliaceae), guava and several Citrus spp. were identified as preferred roosting hosts for oriental fruit fly. Guava had not previously been identified as a preferred roosting host for melon fly. Other than for the use of panax as a roosting host, there has previously been little attention to roosting hosts for oriental fruit fly. Establishment of preferred roosting hosts as crop borders may help to improve suppression of both fruit fly species by providing sites for bait spray applications. Further research is needed to assess the use of vegetation bordering other host crops as roosting hosts, especially for oriental fruit fly. PMID:20334596

Anisotropy of magnetic susceptibility versus lattice- and shape-preferred orientation in the Lac Tio hemo-ilmenite ore body (Grenville province, Quebec)

NASA Astrophysics Data System (ADS)

Bolle, Olivier; Charlier, Bernard; Bascou, Jérôme; Diot, Hervé; McEnroe, Suzanne A.

2014-08-01

The Lac Tio hemo-ilmenite ore body crops out in the outer portion of the 1.06 Ga Lac Allard anorthosite, a member of the Havre-Saint-Pierre anorthosite suite from the Grenville province of North America. It is made up of ilmenitite (commonly with more than 95% hemo-ilmenite) associated with noritic lithologies and anorthosite. The present study compares the magnetic fabric of the ore body, as deduced from anisotropy of magnetic susceptibility (AMS) measurements, with the crystallographic and shape fabrics, obtained from lattice-preferred orientation (LPO) and shape-preferred orientation (SPO) measurements made using electron backscattered diffraction (EBSD) and 3D image analysis, respectively. Room-temperature hysteresis measurements, thermomagnetic curves and values of the bulk magnetic susceptibility reveal a magnetic mineralogy dominated by a mixed contribution of hemo-ilmenite and magnetite. The hemo-ilmenite grains display a LPO characterized by a strong preferred orientation of the basal (0001) plane of ilmenite along which hematite was exsolved. This LPO and the magnetic fabric fit well (angle between the crystallographic c-axis and the axis of minimum susceptibility ≤ ca. 15° for most samples), and the latter is thus strongly influenced by the hemo-ilmenite magneto-crystalline anisotropy. A magnetite SPO, concordant with the hemo-ilmenite LPO, may also influence and even dominate the magnetic fabric. The rock shape fabric is coaxial with the magnetic fabric that can thus be used to perform detailed structural mapping. Interpretation of the magnetic fabric and field structural data suggests that the Lac Tio ore body would be a sag point at the margin of the Lac Allard anorthosite, deformed by ballooning during the final stage of diapiric emplacement of the anorthosite body.

The attracting power of the gaze of politicians is modulated by the personality and ideological attitude of their voters: a functional magnetic resonance imaging study.

PubMed

Cazzato, Valentina; Liuzza, Marco Tullio; Caprara, Gian Vittorio; Macaluso, Emiliano; Aglioti, Salvatore Maria

2015-10-01

Observing someone rapidly moving their eyes induces reflexive shifts of overt and covert attention in the onlooker. Previous studies have shown that this process can be modulated by the onlooker's personality, as well as by the social features of the person depicted in the cued face. Here, we investigated whether an individual's preference for social dominance orientation, in-group perceived similarity (PS), and political affiliation of the cued-face modulated neural activity within specific nodes of the social attention network. During functional magnetic resonance imaging, participants were requested to perform a gaze-following task to investigate whether the directional gaze of various Italian political personages might influence the oculomotor behaviour of in-group or out-group voters. After scanning, we acquired measures of PS in personality traits with each political personage and preference for social dominance orientation. Behavioural data showed that higher gaze interference for in-group than out-group political personages was predicted by a higher preference for social hierarchy. Higher blood oxygenation level-dependent activity in incongruent vs. congruent conditions was found in areas associated with orienting to socially salient events and monitoring response conflict, namely the left frontal eye field, right supramarginal gyrus, mid-cingulate cortex and left anterior insula. Interestingly, higher ratings of PS with the in-group and less preference for social hierarchy predicted increased activity in the left frontal eye field during distracting gaze movements of in-group as compared with out-group political personages. Our results suggest that neural activity in the social orienting circuit is modulated by higher-order social dimensions, such as in-group PS and individual differences in ideological attitudes. © 2015 Federation of European Neuroscience Societies and John Wiley & Sons Ltd.

Effects of a school reform on longitudinal stability of students' preferences with regard to education.

PubMed

Könings, Karen D; Brand-Gruwel, Saskia; Elen, Jan

2012-09-01

Students' perspective on education is of crucial importance for its effectivity, but students' opinions are seldom acknowledged by teachers and designers. Student participation in the educational design process could be a suitable tool to better take students' preferences into account. However, for effective participatory design, it is necessary to know whether students have stable preferences for the design of their education. Changeability of preferences would require a more continuing design process allowing continuous adaptations. This longitudinal survey study aimed to determine the changeability over time of students' preferences for different aspects of a learning environment. Additionally, causes of possible changes in preferences are investigated. The participants were 1,335 high school students of five schools for secondary education in the Netherlands, joining this study during a period of 2 years. Data about students' preferences were collected at three moments, using the Inventory of Perceived Study Environment Extended. Learning-related student characteristics, such as processing strategies and motivational orientations, were measured with the Inventory of Learning Styles. Additionally, data on learning performances were collected. The results showed stability on preferences for almost all studied characteristics of the learning environment. Particularly remarkable was a drop in desirability for student autonomy. This was larger for students with a certificate-oriented motivation and smaller for self-regulated students. Additionally, poorly performing students had a larger decrease in preference for autonomy. The stability on most aspects supports that participatory design might result in fairly stable instructional designs, although caution is needed with respect to student autonomy. ©2011 The British Psychological Society.

Raman Scattering from Tin

DTIC Science & Technology

2015-09-01

ARL-TR-7448 ● SEP 2015 US Army Research Laboratory Raman Scattering from Tin by Patrick A Folkes, Patrick Taylor, Charles Rong...REPORT TYPE 3. DATES COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE Raman Scattering from Tin 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c... tin as an analytical tool for discerning specific allotropic differences in ultra-thin tin films, and discerning differences between the tin and the

Analyzing Morton's Typology of Service Paradigms and Integrity

ERIC Educational Resources Information Center

Bringle, Robert G.; Hatcher, Julie A.; McIntosh, Rachel E.

2006-01-01

Research on college students found limited support for Morton's (1995) hypothesis that students have a preference for one distinct type of service orientation (i.e., charity, project, social change). The findings did replicate previous findings that college students prefer the charity paradigm. A measure of integrity was developed and two…

Discovering Learning Preferences and Learning Differences in the Classroom.

ERIC Educational Resources Information Center

Bargar, June R.; And Others

Understanding learning differences and how they function in the classroom is important to both students and teachers. The learning preferences described in this handbook are based on the concepts of psychological type developed by Carl Jung. Jung identified three sets of psychological processes, the areas of attitude (orientation), perception, and…

Collectivists' Contingency and Autonomy as Predictors of Buffet Preferences among Taiwanese Adolescents

ERIC Educational Resources Information Center

Chiou, Wen-Bin

2006-01-01

In a culture or society with high collectivism, contingent orientation and constrained autonomy are the prominent characteristics of adolescents' self-construal. This article examined whether Taiwanese adolescents' contingency and autonomy were associated with their prevalent preferences for buffet consumption. Findings in a panel survey indicated…

Reproductive isolation between Zaluzianskya species: the influence of volatiles and flower orientation on hawkmoth foraging choices.

PubMed

Campbell, Diane R; Jürgens, Andreas; Johnson, Steven D

2016-04-01

Floral trait differences between related species may play a key role in reproductive isolation imposed by pollinators. Volatile emissions can influence pollinator choice, but how they act in combination with traits such as flower orientation is rarely studied. We compared flower-opening patterns, morphology, colour, orientation and volatile emissions for two closely related species of Zaluzianskya and their natural hybrids. Hawkmoth pollinators were tested for preference between flowers of the two species, and between flowers with manipulations of volatiles or orientation. Flowers of Z. natalensis and Z. microsiphon open at night and day, respectively, but they overlap during early evening, when hawkmoths showed a strong preference for Z. natalensis. The species have similar flower size and colour, but Z. natalensis emits more floral volatiles in the evening and presents flowers vertically face-up as opposed to horizontally in Z. microsiphon, whereas natural hybrids are intermediate. Adding methyl benzoate and linalool to flowers of Z. microsiphon did not increase hawkmoth attraction, but re-orientation of flowers to face vertically increased attraction when scent cues were present, whereas re-orientation of Z. natalensis flowers to face horizontally decreased attraction. This study highlights the importance of flower orientation in imposing reproductive isolation. © 2015 The Authors. New Phytologist © 2015 New Phytologist Trust.

Social value orientation: theoretical and measurement issues in the study of social preferences.

PubMed

Murphy, Ryan O; Ackermann, Kurt A

2014-02-01

What motivates people when they make decisions and how those motivations are potentially entangled with concerns for others are central topics for the social, cognitive, and behavioral sciences. According to the postulate of narrow self-interest, decision makers have the goal of maximizing personal payoffs and are wholly indifferent to the consequences for others. The postulate of narrow self-interest-which has been influential in economics, psychology, and sociology-is precise and powerful but is often simply wrong. Its inadequacy is well known and efforts have been made to develop reliable and valid measurement methods to quantify the more nuanced social preferences that people really have. In this paper, we report on the emergence and development of the predominant conceptualization of social preferences in psychology: social value orientation (SVO). Second, we discuss the relationship between measurement and theory development of the SVO construct. We then provide an overview of the literature regarding measurement methods that have been used to assess individual variations in social preferences. We conclude with a comparative evaluation of the various measures and provide suggestions regarding the measures' constructive use in building psychologically realistic theories of people's social preferences.

CuInS2 Films Deposited by Aerosol-Assisted Chemical Vapor Deposition Using Ternary Single-Source Precursors

NASA Technical Reports Server (NTRS)

Jin, Michael; Banger, Kal; Harris, Jerry; Hepp, Aloysius

2003-01-01

Polycrystalline CuInS2 films were deposited by aerosol-assisted chemical vapor deposition using both solid and liquid ternary single-source precursors (SSPs) which were prepared in-house. Films with either (112) or (204/220) preferred orientation, had a chalcopyrite structure, and (112)-oriented films contained more copper than (204/220)-oriented films. The preferred orientation of the film is likely related to the decomposition and reaction kinetics associated with the molecular structure of the precursors at the substrate. Interestingly, the (204/220)-oriented films were always In-rich and were accompanied by a secondary phase. From the results of post-growth annealing, etching experiments, and Raman spectroscopic data, the secondary phase was identified as an In-rich compound. On the contrary, (112)-oriented films were always obtained with a minimal amount of the secondary phase, and had a maximum grain size of about 0.5 micron. Electrical and optical properties of all the films grown were characterized. They all showed p-type conduction with an electrical resistivity between 0.1 and 30 Omega-cm, and an optical band gap of approximately 1.46 eV +/- 0.02, as deposited. The material properties of deposited films revealed this methodology of using SSPs for fabricating chalcopyrite-based solar cells to be highly promising.

Lateral Spread of Orientation Selectivity in V1 is Controlled by Intracortical Cooperativity

PubMed Central

Chavane, Frédéric; Sharon, Dahlia; Jancke, Dirk; Marre, Olivier; Frégnac, Yves; Grinvald, Amiram

2011-01-01

Neurons in the primary visual cortex receive subliminal information originating from the periphery of their receptive fields (RF) through a variety of cortical connections. In the cat primary visual cortex, long-range horizontal axons have been reported to preferentially bind to distant columns of similar orientation preferences, whereas feedback connections from higher visual areas provide a more diverse functional input. To understand the role of these lateral interactions, it is crucial to characterize their effective functional connectivity and tuning properties. However, the overall functional impact of cortical lateral connections, whatever their anatomical origin, is unknown since it has never been directly characterized. Using direct measurements of postsynaptic integration in cat areas 17 and 18, we performed multi-scale assessments of the functional impact of visually driven lateral networks. Voltage-sensitive dye imaging showed that local oriented stimuli evoke an orientation-selective activity that remains confined to the cortical feedforward imprint of the stimulus. Beyond a distance of one hypercolumn, the lateral spread of cortical activity gradually lost its orientation preference approximated as an exponential with a space constant of about 1 mm. Intracellular recordings showed that this loss of orientation selectivity arises from the diversity of converging synaptic input patterns originating from outside the classical RF. In contrast, when the stimulus size was increased, we observed orientation-selective spread of activation beyond the feedforward imprint. We conclude that stimulus-induced cooperativity enhances the long-range orientation-selective spread. PMID:21629708

The relationship between parenting and the economic orientation and behavior of Norwegian adolescents.

PubMed

Nyhus, Ellen K; Webley, Paul

2013-01-01

Little is known about the economic socialization of children and adolescents and the role of parents in this process. The authors' purpose was to explore the role of parenting in the intergenerational transfer of economic orientation and economic behavior. More specifically, they studied the link between four parenting dimensions (parental warmth-responsiveness, behavioral control, psychological control, autonomy granting), three parenting styles (authoritative, authoritarian, and neglectful) and adolescents' conscientiousness, future time perspective, and present hedonistic orientation. The authors also studied the relationships between these dispositions and the adolescents' spending preferences and ability to control spending. They used data collected from 14-16-year-olds (n = 597) and their parents (n = 469) in Norway. Results showed that adolescents who perceived their parents as psychologically controlling were less future oriented and conscientious, and were more present hedonistic oriented than others, while adolescents who perceived their parents as responsive, autonomy granting, and controlling of behavior were more future orientated and conscientious than others. Adolescents' scores for conscientiousness and future orientation were negatively associated with preferences for spending and positively with the ability to control spending, while the opposite relationships were found with respect to a present hedonistic orientation. Parental style was also found to be important for the future educational plans of adolescents, and plans for higher education were more frequent among adolescents who characterized their parents as authoritative than among those who perceived their parents as neglectful. Implications of the findings for economic socialization are discussed.

Electrochemical study of highly durable cathode with Pt supported on ITO-CNT composite for proton exchange membrane fuel cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Sehkyu; Shao, Yuyan; Viswanathan, Vilayanur V.

2016-10-01

In this paper, we describe a highly stable cathode containing a Pt catalyst supported on an indium tin oxide (ITO) and carbon nanotube (CNT) composite. The dependence of cathode performance and durability on the ITO content and the diameter of the CNTs were investigated by electrochemical techniques. The cathode with 30 wt% ITO and CNTs with diameters 10–20 nm in the composite offered preferred locations for Pt stabilization and was very resistant to carbon corrosion (i.e., 82.7% ESA retention and 105.7% mass activity retention after an accelerated stress test for 400 h).

Multi-layer micro/nanofluid devices with bio-nanovalves

DOEpatents

Li, Hao; Ocola, Leonidas E.; Auciello, Orlando H.; Firestone, Millicent A.

2013-01-01

A user-friendly multi-layer micro/nanofluidic flow device and micro/nano fabrication process are provided for numerous uses. The multi-layer micro/nanofluidic flow device can comprise: a substrate, such as indium tin oxide coated glass (ITO glass); a conductive layer of ferroelectric material, preferably comprising a PZT layer of lead zirconate titanate (PZT) positioned on the substrate; electrodes connected to the conductive layer; a nanofluidics layer positioned on the conductive layer and defining nanochannels; a microfluidics layer positioned upon the nanofluidics layer and defining microchannels; and biomolecular nanovalves providing bio-nanovalves which are moveable from a closed position to an open position to control fluid flow at a nanoscale.

Graphoepitaxy by encapsulation

DOEpatents

Geis, M.W.; Smith, H.I.; Antoniadis, D.A.; Flanders, D.C.

1986-01-21

Improvements on the graphoepitaxial process for obtaining epitaxial or preferred orientation films are described wherein a cap of material is formed over the film to be oriented, artificial surface-relief structure may be present in the substrate, the cap, or both, and the film may be heated by irradiation with electromagnetic radiation. 13 figs.

Prospective Teachers' Value Orientations as Determinants of Preference for External and Anonymous Whistleblowing

ERIC Educational Resources Information Center

Gokce, Asiye Toker

2013-01-01

Whistle-blowing indicates disclosing organizational wrongdoings resulting in harm to third parties. An individual's decision to blow the whistle might be based upon organizational, situational or personal factors. This study inquires the relationship between value orientations of prospective teachers and choices for whistle-blowing with particular…

Job Orientation of Black and White College Graduates in Business.

ERIC Educational Resources Information Center

Brenner, O. C.; Tomkiewicz, Joseph

1982-01-01

Examined differences in job orientation between Black and White male and female business college graduates. Significant race differences were found. Factor analysis indicates that Blacks value long-range career objectives and structure considerably more than do Whites, while their preference for intrinsic and extrinsic factors was less pronounced.…

Prenatal administration of letrozole reduces SDN and SCN volume and cell number independent of partner preference in the male rat.

PubMed

Olvera-Hernández, Sandra; Tapia-Rodríguez, Miguel; Swaab, Dick F; Fernández-Guasti, Alonso

2017-03-15

During development, the exposure to testosterone, and its conversion to estradiol by an enzyme complex termed aromatase, appears to be essential in adult male rats for the expression of typical male sexual behavior and female-sex preference. Some hypothalamic areas are the supposed neural bases of sexual preference/orientation; for example, male-oriented rams have a reduced volume of the sexually dimorphic nucleus (oSDN), while in homosexual men this nucleus does not differ from that of heterosexual men. In contrast, homosexual men showed a larger number of vasopressinergic cells in the suprachiasmatic nucleus (SCN). Interestingly, male rats perinatally treated with an aromatase inhibitor, 1,4,6-androstatriene-3,17-dione (ATD), also showed bisexual preference and an increased number of vasopressinergic neurons in the SCN. However, this steroidal aromatase inhibitor has affinity for all three steroid receptors. Recently, we reported that the prenatal administration of the selective aromatase inhibitor, letrozole, produced a subpopulation of males with same-sex preference. The aim of this study was to compare the volume and number of cells of the SDN and SCN (the latter nucleus was immunohistochemically stained for vasopressin) between males treated with letrozole with same-sex preference, males treated with letrozole with female preference and control males with female preference. Results showed that all males prenatally treated with letrozole have a reduced volume and estimated cell number in the SDN and SCN, independent of their partner preference. These results indicate that the changes in these brain areas are not related to sexual preference, but rather to the effects of letrozole. The divergent results may be explained by species differences as well as by the critical windows during which the aromatase inhibitor was administered. Copyright © 2017 Elsevier Inc. All rights reserved.

Reconstruction of the 3-D Shape and Crystal Preferred Orientation of Olivine: A Combined X-ray µ-CT and EBSD-SEM approach

NASA Astrophysics Data System (ADS)

Kahl, Wolf-Achim; Hidas, Károly; Dilissen, Nicole; Garrido, Carlos J.; López-Sánchez Vizcaíno, Vicente; Jesús Román-Alpiste, Manuel

2017-04-01

The complete reconstruction of the microstructure of rocks requires, among others, a full description of the shape preferred orientation (SPO) and crystal preferred orientation (CPO) of the constituent mineral phases. New advances in instrumental analyses, particularly electron backscatter diffraction (EBSD) coupled to focused ion beam-scanning electron microscope (FIB-SEM), allows a complete characterization of SPO and CPO in rocks at the micron scale [1-2]. Unfortunately, the large grain size of many crystalline rocks, such as peridotite, prevents a representative characterization of the CPO and SPO of their constituent minerals by this technique. Here, we present a new approach combining X-ray micro computed tomography (µ-CT) and EBSD to reconstruct the geographically oriented, 3-D SPO and CPO of cm- to mm-sized olivine crystals in two contrasting fabric types of chlorite harzburgites (Almírez ultramafic massif, SE Spain). The semi-destructive sample treatment involves drilling of geographically oriented micro drills in the field and preparation of oriented thin sections from µ-CT scanned cores. This allows for establishing the link among geological structures, macrostructure, fabric, and 3-D SPO-CPO at the thin section scale. Based on EBSD analyses, different CPO groups of olivine crystals can be discriminated in the thin sections and allocated to 3-D SPO in the µ-CT volume data. This approach overcomes the limitations of both methods (i.e., no crystal orientation data in µ-CT and no spatial information in EBSD), hence 3-D orientation of the crystallographic axes of olivines from different orientation groups could be correlated with the crystal shapes of olivine grains. This combined µ-CT and EBSD technique enables the correlation of both SPO and CPO and representative grain size, and is capable to characterize the 3-D microstructure of olivine-bearing rocks at the hand specimen scale. REFERENCES 1. Zaefferer, S., Wright, S.I., Raabe, D., 2008. Three-Dimensional orientation microscopy in a focused ion beam-scanning electron microscope: A new dimension of microstructure characterization. Metallurgical and Materials Transactions A 39, 374-389. 2. Burnett, T.L., Kelley, R., Winiarski, B., Contreras, L., Daly, M., Gholinia, A., Burke, M.G., Withers, P.J., 2016. Large volume serial section tomography by Xe Plasma FIB dual beam microscopy. Ultramicroscopy 161, 119-129.

42 CFR 425.306 - Participation agreement and exclusivity of ACO participant TINs.

Code of Federal Regulations, 2014 CFR

2014-10-01

... participant TINs. 425.306 Section 425.306 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT... participant TINs. (a) For purposes of the Shared Savings Program, each ACO participant TIN is required to commit to a participation agreement with CMS. (b) Each ACO participant TIN upon which beneficiary...

78 FR 16048 - Proposed Collection; Comment Request for e-Services Registration TIN Matching-Application and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-13

...-Services Registration TIN Matching--Application and Screens for TIN Matching Interactive AGENCY: Internal...(c)(2)(A)). Currently, the IRS is soliciting comments concerning e- Services registration TIN matching--application and screens for TIN matching interactive. DATES: Written comments should be received...

42 CFR 425.306 - Participation agreement and exclusivity of ACO participant TINs.

Code of Federal Regulations, 2013 CFR

2013-10-01

... participant TINs. 425.306 Section 425.306 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT... participant TINs. (a) For purposes of the Shared Savings Program, each ACO participant TIN is required to commit to a participation agreement with CMS. (b) Each ACO participant TIN upon which beneficiary...

75 FR 5854 - Proposed Collection; Comment Request for e-Services Registration TIN Matching-Application and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-04

...-Services Registration TIN Matching--Application and Screens for TIN Matching Interactive AGENCY: Internal...(c)(2)(A)). Currently, the IRS is soliciting comments concerning e- Services Registration TIN Matching--Application and Screens for TIN Matching Interactive. DATES: Written comments should be received...

42 CFR 425.306 - Participation agreement and exclusivity of ACO participant TINs.

Code of Federal Regulations, 2012 CFR

2012-10-01

... participant TINs. 425.306 Section 425.306 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT... participant TINs. (a) For purposes of the Shared Savings Program, each ACO participant TIN is required to commit to a participation agreement with CMS. (b) Each ACO participant TIN upon which beneficiary...

Epigenetic lead, zinc, silver, antimony, tin, and gold veins in Boulder Basin, Blaine and Custer counties, Idaho; potential for economic tin mineralization

USGS Publications Warehouse

Ratchford, Michael E.

2002-01-01

Boulder Basin is in a northwest-trending belt of allochthonous Paleozoic rocks in the Boulder Mountains of central Idaho. Regional Tertiary extension resulted in widespread normal faulting and coeval emplacement of shallow-level intrusions and extrusive rocks of the Challis Volcanic Group. Epigenetic lead-zinc-silver-antimony-tin-gold vein deposits formed during Tertiary extension and are hosted within Paleozoic strata. The major orebodies are in the lower plate of the Boulder Basin thrust fault, in massive quartzite of the Middle Pennsylvanian to Lower Permian Wood River Formation. Anomalous concentrations of tin are present in the base-metal mineral assemblage of the Boulder Basin ore deposits. The tin-bearing veins in Boulder Basin are strikingly similar to Bolivian tin deposits. The deposit model for Bolivian tin deposits identifies buried tin porphyry below the tin-bearing vein system.

Default Options In Advance Directives Influence How Patients Set Goals For End-Of-Life Care

PubMed Central

Halpern, Scott D.; Loewenstein, George; Volpp, Kevin G.; Cooney, Elizabeth; Vranas, Kelly; Quill, Caroline M.; Mckenzie, Mary S.; Harhay, Michael O.; Gabler, Nicole B.; Silva, Tatiana; Arnold, Robert; Angus, Derek C.; Bryce, Cindy

2015-01-01

Although decisions regarding end-of-life care are personal and important, they may be influenced by the ways in which options are presented. To test this hypothesis, we randomly assigned 132 seriously ill patients to complete one of three types of advance directives. Two types had end-of-life care options already checked—a default choice—but one of these favored comfort-oriented care, and the other, life-extending care. The third type was a standard advance directive with no options checked. We found that most patients preferred comfort-oriented care, but the defaults influenced those choices. For example, 77 percent of patients in the comfort-oriented group retained that choice, while 43 percent of those in the life-extending group rejected the default choice and selected comfort-oriented care instead. Among the standard advance directive group, 61 percent of patients selected comfort-oriented care. Our findings suggest that patients may not hold deep-seated preferences regarding end-of-life care. The findings provide motivation for future research examining whether using default options in advance directives may improve important outcomes, including patients’ receipt of wanted and unwanted services, resource use, survival, and quality of life. PMID:23381535

Controlling the preferential orientation in sol-gel prepared CaCu3Ti4O12 thin films by LaAlO3 and NdGaO3 substrates

NASA Astrophysics Data System (ADS)

Pongpaiboonkul, Suriyong; Kasa, Yumairah; Phokharatkul, Ditsayut; Putasaeng, Bundit; Hodak, Jose H.; Wisitsoraat, Anurat; Hodak, Satreerat K.

2016-11-01

Researchers have paid considerable attention to CaCu3Ti4O12 (CCTO) due to the colossal dielectric constant over a wide range of frequency and temperature. Despite of the growing number of works dealing with CCTO, there have been few studies of the role played by the substrate in inducing structural and dielectric effects of this material. In this work, highly-oriented CCTO thin films have been deposited on LaAlO3(100), NdGaO3(100) and NdGaO3(110) substrates using a sol-gel method. These single crystal substrates were chosen in terms of small lattice mismatch between CCTO and the substrate. The X-ray diffraction patterns showed that the CCTO film layers grow with different orientations depending upon the substrate used. We show that the preferred orientation of CCTO thin films can be manipulated to a high degree by growing it on specific crystal planes of the substrates without the use of buffer layers. Colossal dielectric constants are observed in our films which appear to correlate with the film crystallinity and preferred orientation.

The political (and physiological) divide: Political orientation, performance monitoring, and the anterior cingulate response.

PubMed

Weissflog, Meghan; Choma, Becky L; Dywan, Jane; van Noordt, Stefon J R; Segalowitz, Sidney J

2013-01-01

Our goal was to test a model of sociopolitical attitudes that posits a relationship between individual differences in liberal versus conservative political orientation and differential levels of anterior cingulate cortex (ACC) responsivity. We recorded event-related potentials (ERPs) while participants who varied along a unidimensional liberal-conservative continuum engaged in a standard Go/NoGo task. We also measured component attitudes of political orientation in the form of traditionalism (degree of openness to social change) and egalitarianism (a preference for social equality). Generally, participants who reported a more liberal political orientation made fewer errors and produced larger ACC-generated ERPs (the error-related negativity, or ERN and the NoGo N2). This ACC activation, especially as indicated by a larger NoGo N2, was most strongly associated with greater preference for social equality. Performance accuracy, however, was most strongly associated with greater openness to social change. These data are consistent with a social neuroscience view that sociopolitical attitudes are related to aspects of neurophysiological responsivity. They also indicate that a bidimensional model of political orientation can enhance our interpretation of the nature of these associations.

Revisiting elastic anisotropy of biotite gneiss from the Outokumpu scientific drill hole based on new texture measurements and texture-based velocity calculations

NASA Astrophysics Data System (ADS)

Wenk, H.-R.; Vasin, R. N.; Kern, H.; Matthies, S.; Vogel, S. C.; Ivankina, T. I.

2012-10-01

A sample of biotite gneiss from the Outokumpu deep drilling project in Finland was investigated by Kern et al. (2008) for crystal preferred orientation and elastic anisotropy. Considerable differences between measured acoustic velocities and velocities calculated on the basis of texture patterns were observed. Measured P-wave anisotropy was 15.1% versus a Voigt average yielding 7.9%. Here we investigate the same sample with different methods and using different averaging techniques. Analyzing time-of-flight neutron diffraction data from Dubna-SKAT and LANSCE-HIPPO diffractometers with the Rietveld technique, much stronger preferred orientation for biotite is determined, compared to conventional pole-figure analysis reported previously. The comparison reveals important differences: HIPPO has much better counting statistics but pole figure coverage is poor. SKAT has better angular resolution. Using the new preferred orientation data and applying a self-consistent averaging method that takes grain shapes into account, close agreement of calculated and measured P-wave velocities is observed (12.6%). This is further improved by adding 0.1 vol.% flat micropores parallel to the biotite platelets in the simulation (14.9%).

Radial Bias Is Not Necessary For Orientation Decoding

PubMed Central

Pratte, Michael S.; Sy, Jocelyn L.; Swisher, Jascha D.; Tong, Frank

2015-01-01

Multivariate pattern analysis can be used to decode the orientation of a viewed grating from fMRI signals in early visual areas. Although some studies have reported identifying multiple sources of the orientation information that make decoding possible, a recent study argued that orientation decoding is only possible because of a single source: a coarse-scale retinotopically organized preference for radial orientations. Here we aim to resolve these discrepant findings. We show that there were subtle, but critical, experimental design choices that led to the erroneous conclusion that a radial bias is the only source of orientation information in fMRI signals. In particular, we show that the reliance on a fast temporal-encoding paradigm for spatial mapping can be problematic, as effects of space and time become conflated and lead to distorted estimates of a voxel’s orientation or retinotopic preference. When we implement minor changes to the temporal paradigm or to the visual stimulus itself, by slowing the periodic rotation of the stimulus or by smoothing its contrast-energy profile, we find significant evidence of orientation information that does not originate from radial bias. In an additional block-paradigm experiment where space and time were not conflated, we apply a formal model comparison approach and find that many voxels exhibit more complex tuning properties than predicted by radial bias alone or in combination with other known coarse-scale biases. Our findings support the conclusion that radial bias is not necessary for orientation decoding. In addition, our study highlights potential limitations of using temporal phase-encoded fMRI designs for characterizing voxel tuning properties. PMID:26666900

The Effect of Surface Induced Flows on Bubble and Particle Aggregation

NASA Technical Reports Server (NTRS)

Guelcher, Scott A.; Solomentsev, Yuri E.; Anderson, John L.; Boehmer, Marcel; Sides, Paul J.

1999-01-01

Almost 20 years have elapsed since a phenomenon called "radial specific coalescence" was identified. During studies of electrolytic oxygen evolution from the back side of a vertically oriented, transparent tin oxide electrode in alkaline electrolyte, one of the authors (Sides) observed that large "collector" bubbles appeared to attract smaller bubbles. The bubbles moved parallel to the surface of the electrode, while the electric field was normal to the electrode surface. The phenomenon was reported but not explained. More recently self ordering of latex particles was observed during electrophoretic deposition at low DC voltages likewise on a transparent tin oxide electrode. As in the bubble work, the field was normal to the electrode while the particles moved parallel to it. Fluid convection caused by surface induced flows (SIF) can explain these two apparently different experimental observations: the aggregation of particles on an electrode during electrophoretic deposition, and a radial bubble coalescence pattern on an electrode during electrolytic gas evolution. An externally imposed driving force (the gradient of electrical potential or temperature), interacting with the surface of particles or bubbles very near a planar conducting surface, drives the convection of fluid that causes particles and bubbles to approach each other on the electrode.

Functional implications of orientation maps in primary visual cortex

NASA Astrophysics Data System (ADS)

Koch, Erin; Jin, Jianzhong; Alonso, Jose M.; Zaidi, Qasim

2016-11-01

Stimulus orientation in the primary visual cortex of primates and carnivores is mapped as iso-orientation domains radiating from pinwheel centres, where orientation preferences of neighbouring cells change circularly. Whether this orientation map has a function is currently debated, because many mammals, such as rodents, do not have such maps. Here we show that two fundamental properties of visual cortical responses, contrast saturation and cross-orientation suppression, are stronger within cat iso-orientation domains than at pinwheel centres. These differences develop when excitation (not normalization) from neighbouring oriented neurons is applied to different cortical orientation domains and then balanced by inhibition from un-oriented neurons. The functions of the pinwheel mosaic emerge from these local intra-cortical computations: Narrower tuning, greater cross-orientation suppression and higher contrast gain of iso-orientation cells facilitate extraction of object contours from images, whereas broader tuning, greater linearity and less suppression of pinwheel cells generate selectivity for surface patterns and textures.

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2011 CFR

2011-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2014 CFR

2014-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2013 CFR

2013-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

78 FR 39644 - Information Reporting for Affordable Insurance Exchanges

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-02

... Exchange-- (i) The name, address, and taxpayer identification number (TIN), or date of birth if a TIN is... advance credit payments (taxpayer), and the name and TIN of the individual's spouse, if applicable; (ii) The name, address, and TIN, or date of birth if a TIN is not available, of an adult enrolling in...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2010 CFR

2010-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2012 CFR

2012-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

The prognostic value of tumor-infiltrating neutrophils in gastric adenocarcinoma after resection.

PubMed

Zhao, Jing-jing; Pan, Ke; Wang, Wei; Chen, Ju-gao; Wu, Yan-heng; Lv, Lin; Li, Jian-jun; Chen, Yi-bing; Wang, Dan-dan; Pan, Qiu-zhong; Li, Xiao-dong; Xia, Jian-chuan

2012-01-01

Several pieces of evidence indicate that tumor-infiltrating neutrophils (TINs) are correlated to tumor progression. In the current study, we explore the relationship between TINs and clinicopathological features of gastric adenocarcinoma patients. Furthermore, we investigated the prognostic value of TINs. The study was comprised of two groups, training group (115 patients) and test group (97 patients). Biomarkers (intratumoral CD15+ neutrophils) were assessed by immunohistochemistry. The relationship between clinicopathological features and patient outcome were evaluated using Cox regression and Kaplan-Meier analysis. Immunohistochemical detection showed that the tumor-infiltrating neutrophils (TINs) in the training group ranged from 0.00-115.70 cells/high-power microscopic field (HPF) and the median number was 21.60 cells/HPF. Based on the median number, the patients were divided into high and low TINs groups. Chi-square test analysis revealed that the density of CD15+ TINs was positively associated with lymph node metastasis (p = 0.024), distance metastasis (p = 0.004) and UICC (International Union Against Cancer) staging (p = 0.028). Kaplan-Meier analysis showed that patients with a lower density of TINs had a better prognosis than patients with a higher density of TINs (p = 0.002). Multivariate Cox's analysis showed that the density of CD15+ TINs was an independent prognostic factor for overall survival of gastric adenocarcinoma patients. Using another 97 patients as a test group and basing on the median number of TINs (21.60 cells/HPF) coming from the training group, Kaplan-Meier analysis also showed that patients with a lower density of TINs had a better prognosis than patients with a higher density of TINs (p = 0.032). The results verify that the number of CD15+ TINs can predict the survival of gastric adenocarcinoma surgical patients. The presence of CD15+ TINs is an independent and unfavorable factor in the prognosis of gastric adenocarcinoma patients. Targeting CD15+ TINs may be a potential intervenient therapy in the future.

Evaluation of the suitability of tin slag in cementitious materials: Mechanical properties and Leaching behaviour

NASA Astrophysics Data System (ADS)

Rustandi, Andi; Wafa' Nawawi, Fuad; Pratesa, Yudha; Cahyadi, Agung

2018-01-01

Tin slag, a by-product of tin production has been used in cementitious application. The present investigation focuses on the suitability of tin slag as primary component in cement and as component that substitute some amount of Portland Cement. The tin slags studied were taken from Bangka, Indonesia. The main contents of the tin slag are SiO2, Al2O3, and Fe2O3 according to the XRF investigation. The aim of this article was to study the mechanical behaviour (compressive strength), microstructure and leaching behaviour of tin slag blended cement. This study used air-cooled tin slag that had been passed through 400# sieve to replace Portland Cement with ratio 0, 10, 20, 30, 40 by weight. Cement pastes and tin slag blended cement pastes were prepared by using water/cement ratio (W/C) of 0.40 by weight and hydrated for various curing ages of 3, 7, 14 days The microstructure of the raw tin slag was investigated using Scanning Electron Microscope (SEM). The phase composition of each cement paste was investigated using X-ray Diffraction (XRD). The aim of the leachability test was to investigate the environmental impacts of tin slag blended cement product in the range 4-8 pH by using static pH-dependent leaching test. The result show that the increase of the tin slag content decreasing the mortar compressive strength at early ages. The use of tin slag in cement provide economic benefits for all related industries.

Are larks future-oriented and owls present-oriented? Age- and sex-related shifts in chronotype-time perspective associations.

PubMed

Nowack, Kati; van der Meer, Elke

2013-12-01

The chronotype (morningness/eveningness) relates to individual differences in circadian preferences. Time perspective (past, present, future) refers to the preference to rely on a particular temporal frame for decision-making processes and behavior. First evidence suggests that future time perspective is associated with greater morningness and present time perspective with greater eveningness. However, little is known about how chronotype-time perspective relationships may alter over the life span. This present study investigated links between chronotype and time perspective more thoroughly by taking age and sex into account as well. Seven hundred six participants aged between 17 and 74 completed German adaptations of the Morningness--Eveningness Questionnaire (MEQ) and Zimbardo Time Perspective Inventory (ZTPI). Controlling for age and sex, relationships between morningness and future time perspective as well as between eveningness and present time perspective were replicated. These findings were supported by significant associations between time perspective and midpoint of sleep. Future time perspective was linked to earlier midpoints of sleep, indicating an early chronotype. Present time perspective was associated with later midpoints of sleep, indicating a late chronotype. However, age and sex had an impact on the chronotype-time perspective relationships. In all age groups, male larks were more future-oriented and less present-oriented, male owls more present-oriented and less future-oriented. The same conclusion could be drawn for female adolescents and young adults. For female adults above 30, there was no interrelationship between morningness and future time perspective but between eveningness and past time perspective. Female adult owls were more present-oriented as well as more past-oriented. Female adult larks were less present-oriented and less past-oriented. Findings are discussed in the light of neuroendocrine and serotonergic functioning.

Electronic and Optical Properties of Titanium Nitride Bulk and Surfaces from First Principles Calculations (Postprint)

DTIC Science & Technology

2015-11-18

thickness of the film, or substrate. In this work, we report calculations for titanium nitride ( TiN ), a promising material for plasmonic applications...stoichiometric bulk TiN , as well as of the TiN (100), TiN (110), and TiN (111) outermost surfaces. Density functional theory (DFT) and many-body GW methods...and the band structure for bulk TiN were shown to be consistent with previous work. Calculated dielectric functions, plasma frequencies, reflectivity

Cosmopolitan cities: the frontier in the twenty-first century?

PubMed

Sevincer, A Timur; Kitayama, Shinobu; Varnum, Michael E W

2015-01-01

People with independent (vs. interdependent) social orientation place greater priority on personal success, autonomy, and novel experiences over maintaining ties to their communities of origin. Accordingly, an independent orientation should be linked to a motivational proclivity to move to places that offer economic opportunities, freedom, and diversity. Such places are cities that can be called "cosmopolitan." In support of this hypothesis, Study 1 found that independently oriented young adults showed a preference to move to cosmopolitan rather than noncosmopolitan cities. Study 2 used a priming manipulation and demonstrated a causal impact of independence on residential preferences for cosmopolitan cities. Study 3 established ecological validity by showing that students who actually moved to a cosmopolitan city were more independent than those who either moved to a noncosmopolitan city or never moved. Taken together, the findings illuminate the role of cosmopolitan settlement in the contemporary cultural change toward independence and have implications for urban development and economic growth.

Process parameters, orientation, and functional properties of melt-processed bulk Y-Ba-Cu-O superconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zakharchenko, I.V.; Terryll, K.M.; Rao, K.V.

1995-03-01

This study compared the microstructure, texturing, and functional properties (critical currents) of YBa{sub 2}Cu{sub 3}O{sub 7{minus}x}-based bulk pellets that were prepared by the quench-melt-growth-process (QMGP), melt-textured growth (MTG), and conventional solid-state reaction (SSR) approaches. Using two X-ray diffraction (XRD) methods, {theta}-2{theta}, and rocking curves, the authors found that the individual grains of two melt-processed pellets exhibited remarkable preferred orientational alignment (best rocking curve width = 3.2{degree}). However, the direction of the preferred orientation among the grains was random. Among the three types of bulk materials studied, the QMGP sample was found to have the best J{sub c} values, {approx} 4,500more » A/cm{sup 2} at 77 K in a field of 2 kG, as determined from SQUID magnetic data.« less

Conflict resolution styles: a comparison of assisted living and nursing home facilities.

PubMed

Small, Jeff A; Montoro-Rodriguez, Julian

2006-01-01

In this exploratory study, the authors investigated how interpersonal conflict is resolved in assisted living and nursing home facilities. In particular, the authors examined whether conflict resolution styles differed between type of facility and between residents and staff in each type of facility. Four focus groups were conducted--two with residents and two with staff from each type of facility. The focus groups centered on discussing the occurrence of conflict and how each participant handled it. Discourse analysis was employed to identify participants' use of three styles of conflict resolution: controlling, solution-oriented, and non-confrontational. The results indicate that staff in each care context showed a preference for the solution-oriented approach. Residents in each setting reported equal use of the non-confrontational and solution-oriented styles. The findings suggest that preferred conflict resolution styles may vary more as a function of the role of each communicator than the context of the care setting.

Exploring Juror's Listening Processes: The Effect of Listening Style Preference on Juror Decision Making.

ERIC Educational Resources Information Center

Worthington, Debra L.

2001-01-01

Examines the relationship between listening style preference and jurors' assignment of negligence and damages. Notes that 90 men and 84 women drawn from introductory communication courses viewed videotaped attorney presentations and the judge's instructions from an actual court case. Indicates that participants with a people-oriented listening…

Towards Greater Individualization and Process-Oriented Learning through Electronic Self-Access: Project "e-daf"

ERIC Educational Resources Information Center

Chan, Wai Meng; Kim, Dong-Ha

2004-01-01

Research in cognitive psychology and second language learning has underlined the significance of learners' cognitive processes and individual preferences in language learning. Helping learners to be aware of these processes and preferences has in fact become an important methodological principle of language teaching. Advances in information and…

Early Child Care Teachers' Socialization Goals and Preferred Behavioral Strategies: A Cross-Cultural Comparison

ERIC Educational Resources Information Center

Gernhardt, Ariane; Lamm, Bettina; Keller, Heidi; Döge, Paula

2014-01-01

This study investigated early child care teachers' culturally shaped socialization goals and preferred behavioral strategies. The participants were 183 female teachers and trainees, 93 from Osnabrück, Germany, representing an urban Western context, which can be characterized by a primary cultural orientation toward psychological autonomy and a…

A Market-oriented Approach To Maximizing Product Benefits: Cases in U.S. Forest Products Industries

Treesearch

Vijay S. Reddy; Robert J. Bush; Ronen Roudik

1996-01-01

Conjoint analysis, a decompositional customer preference modelling technique, has seen little application to forest products. However, the technique provides useful information for marketing decisions by quantifying consumer preference functions for multiattribute product alternatives. The results of a conjoint analysis include the contribution of each attribute and...

Attitudes and Preferences of Pennsylvania Primary Care Physicians Regarding Continuing Medical Education.

ERIC Educational Resources Information Center

Mansfield, Phyllis; And Others

Primary care physicians in Pennsylvania were asked to give their attitudes and preferences regarding continuing medical education (CME) in an effort to expand and develop physician-oriented CME programs for the Hershey Continuing Education department at Penn State. A 32-item questionnaire was mailed to 952 primary care physicians practicing in…

76 FR 38129 - Applications for New Awards; Americans With Disabilities Act (ADA) National Network Knowledge...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-29

...) number and a Taxpayer Identification Number (TIN); b. Register both your DUNS number and TIN with the... number and TIN on your application; and d. Maintain an active CCR registration with current information... a TIN from the Internal Revenue Service. If you are an individual, you can obtain a TIN from the...

77 FR 40596 - Applications for New Awards: Disability and Rehabilitation Research Projects and Centers Program...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-10

...) number and a Taxpayer Identification Number (TIN); b. Register both your DUNS number and TIN with the... number and TIN on your application; and d. Maintain an active CCR registration with current information... a TIN from the Internal Revenue Service. If you are an individual, you can obtain a TIN from the...

Empathy differences by gender and specialty preference in medical students: a study in Brazil.

PubMed

Santos, Mariana A; Grosseman, Suely; Morelli, Thiago C; Giuliano, Isabela C B; Erdmann, Thomas R

2016-05-21

We have conducted this study to assess medical students' empathy and to examine empathy differences by students' socio-demographic characteristics, including gender, and specialty preference. We have conducted a cross-sectional and descriptive research. Among 595 medical students registered at the Federal University of Santa Catarina (Brazil) in 2012, we have selected a sample of 320 enrolled in the first, third, fifth, seventh, ninth, eleventh, and in the last semester of the course. The response rate obtained was 70.6% (n=226). Data was collected by using a self-report questionnaire, and the variables analyzed included course semester, socio-demographic characteristics (such as age, gender, household monthly income and parents level of education), students' specialty preference, and empathy assessed by the Jefferson Scale of Empathy. We have used descriptive statistics, 95% Confidence Interval for percentages, Student's t-test, and Analysis of Variance to analyze the data. Mean empathy among students was (M=119.7, SD=9.9), with no difference by according to semester (F=1.5, p=.2). Empathy means were higher among females (M=118.3, SD=10.6) than among males (M=121.0, SD=9.3, t=-2.1, p=.032). Students who preferred a people-oriented specialty obtained significantly higher mean scores (M=121.5, SD=8.1) in comparison to students who preferred technology-oriented specialties (M=118.0, SD=11.3, t=2.4, p=.02). Our study has found consistently high scores of empathy among medical students enrolled in all levels of training at the Federal University of Santa Catarina, and higher empathy among women and students who intend to pursue a people-oriented specialty. Conclusions on higher empathy among medical students require further study.

Influence of Molecular Orientation on Charge-Transfer Processes at Phthalocyanine/Metal Oxide Interfaces and Relationship to Organic Photovoltaic Performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Hsiao-Chu; MacDonald, Gordon A.; Shi, Yanrong

2015-05-04

The effect of the molecular orientation distribution of the first monolayer of donor molecules at the hole-harvesting contact in an organic photovoltaic (OPV) on device efficiency was investigated. Two zinc phthalocyanine (ZnPc) phosphonic acids (PA) deposited on indium tin oxide (ITO) electrodes are compared: ZnPc(PA)4 contains PA linkers in all four quadrants, and ZnPcPA contains a PA linker in one quadrant. ZnPcPA monolayers exhibited a broad distribution of molecular orientations whereas ZnPc(PA)4 adsorption produced a monolayer with a narrower orientation distribution with the molecular plane more parallel to the ITO surface. We used potential-modulated attenuated total reflectance spectroelectrochemistry (PM-ATR) tomore » characterize the charge-transfer kinetics of these films and show that the highest rate constants correspond to ZnPc subpopulations that are oriented more parallel to the ITO surface plane. For ZnPc(PA)4, rate constants exceeded 104 s–1 and are among the highest ever reported for a surface-confined redox couple, which is attributable to both its orientation and the small ZnPc–electrode separation distance. The performance of OPVs with ITO hole-harvesting contacts modified with ZnPc(PA)4 was comparable to that achieved with highly activated bare ITO contacts, whereas for ZnPcPA-modified contacts, the OPV performance was similar to that observed with (hole-blocking) alkyl-PA modifiers. These results demonstrate the synergism between molecular structure, energetics, and dynamics at interfaces in OPVs.« less

The Southeast Asian Tin Belt

NASA Astrophysics Data System (ADS)

Schwartz, M. O.; Rajah, S. S.; Askury, A. K.; Putthapiban, P.; Djaswadi, S.

1995-07-01

The Southeast Asian Tin Belt is a north-south elongate zone 2800 km long and 400 km wide, extending from Burma (Myanmar) and Thailand to Peninsular Malaysia and the Indonesian Tin Islands. Altogether 9.6 million tonnes of tin, equivalent to 54% of the world's tin production is derived from this region. Most of the granitoids in the region can be grouped geographically into elongate provinces or belts, based on petrographic and geochronological features. - The Main Range Granitoid Province in western Peninsular Malaysia, southern Peninsular Thailand and central Thailand is almost entirely made up of biotite granite (184-230 Ma). Tin deposits associated with these granites contributed 55% of the historic tin production of Southeast Asia. - The Northern Granitoid Province in northern Thailand (0.1% of tin production) also has dominant biotite granite (200-269 Ma) but it is distinguished by abundant post-intrusion deformation. - The Eastern Granitoid Province extends from eastern Peninsular Malaysia to eastern Thailand. The Malaysian part is subdivided into the East Coast Belt (220-263 Ma), Boundary Range Belt (197-257 Ma) and Central Belt (79-219 Ma). The granitoids cover a wide compositional range from biotite granite to hornblende-biotite granite/granodiorite and diorite-gabbro. Tin deposits are associated with biotite granite in the East Coast Belt (3% of tin production). The granitoids in the other areas of the Eastern Granitoid Province are barren. - The Western Granitoid Province (22-149 Ma) in northern Peninsular Thailand, western Thailand and Burma has biotite granite and hornblende-biotite granite/granodiorite. Tin deposits are associated with biotite granite, which probably is the dominant phase (14% of tin production). The granitoids of the Indonesian Tin Islands (193-251 Ma) do not permit grouping into geographically distinct units. Main Range-type and Eastern Province-type plutons occur next to each other. Most of the tin deposits are associated with Main Range-type plutons (28% of tin production). Tin-mineralized plutons are characterized by high concentrations of SiO 2, K 2O, Rb, Sn, Th and U, whereas the concentrations of Fe 2O 3, MgO, CaO, Na 2O, Ba and Sr as well as the Fe2O3/FeO ratios are low. Tin-mineralized plutons are also distinguished by high initial 87Sr/86Sr ratios low magnetic susceptibilities.

Intrinsic and extrinsic motivational orientations in the competitive context: an examination of person-situation interactions.

PubMed

Abuhamdeh, Sami; Csikszentmihalyi, Mihaly

2009-10-01

The current study examined Intrinsic Motivation Orientation and Extrinsic Motivation Orientation (Work Preference Inventory; Amabile, Hill, Hennessey, & Tighe, 1994) as potential trait-level moderators of the way Internet chess players responded to the intrinsic and extrinsic rewards of the chess games they played. On the basis of the defining characteristics of these 2 types of motivational orientations, we predicted that (a) Intrinsic Motivation Orientation would be associated with a stronger curvilinear relationship between challenge and enjoyment and (b) Extrinsic Motivation Orientation would be associated with a heightened affective responsivity to competitive outcome (i.e., winning vs. losing). Results supported the predictions. Implications of the findings are discussed.

Exploring the Motivational Orientations of Graduate Students in Distance Education Programs

ERIC Educational Resources Information Center

Nolot, Sandra K.

2011-01-01

This study examined the motivational orientations of 166 graduate students enrolled in distance education courses at a state university. Data were collected utilizing Boshier's Education Participation Scale A-Form and analyses were completed for overall results, by gender and age, by academic program and by preferred method of distance course…

Associations of Parental and Peer Characteristics with Adolescents' Social Dominance Orientation

ERIC Educational Resources Information Center

Cross, Jennifer Riedl; Fletcher, Kathryn L.

2011-01-01

Studies with adults of social dominance orientation (SDO), a preference for inequality among social groups, have found correlations with various prejudices and support for discriminatory practices. This study explores the construct among adolescents at an age when they are beginning to recognize the social groups in their environment, particularly…

Evaluating an Adaptive Equity-Oriented Pedagogy: A Study of Its Impacts in Higher Education

ERIC Educational Resources Information Center

Phuong, Andrew Estrada; Nguyen, Judy; Marie, Dena

2017-01-01

This study examines whether and how an adaptive equity-oriented pedagogy can address diverse college students' needs and preferred modes of learning. Using a mixed-methods approach, we evaluated this pedagogical intervention that synthesizes democratic, assessment-driven, strengths-based, multimodal, and game-based instructional strategies. This…

The Contingency Model of Leadership Effectiveness: Motivational Implications of the Teacher's Role as Leader in the Classroom.

ERIC Educational Resources Information Center

Hardy, Robert C.

Fiedler's Contingency Model postulates that the effectiveness of leaders results from a relationship between leadership style and situational favorability. Leadership style is measured with Fiedler's Least Preferred Coworker Scale, which assesses whether the person rating the coworker is task-oriented or oriented towards interpersonal relations.…

Help to perpetuate traditional gender roles: Benevolent sexism increases engagement in dependency-oriented cross-gender helping.

PubMed

Shnabel, Nurit; Bar-Anan, Yoav; Kende, Anna; Bareket, Orly; Lazar, Yael

2016-01-01

Based on theorizing that helping relations may serve as a subtle mechanism to reinforce intergroup inequality, the present research (N = 1,315) examined the relation between benevolent sexism (i.e., a chivalrous yet subtly oppressive view of women) and helping. In cross-gender interactions, the endorsement of (Studies 1, 3, and 4) or exposure to (Study 2) benevolent sexism predicted (a) men's preference to provide women with dependency-oriented help (i.e., direct assistance) rather than tools for autonomous coping, and (b) women's preference to seek dependency-oriented help rather than tools for autonomous coping. Benevolent sexism did not predict men's and women's engagement in dependency-oriented helping relations in same-gender interactions. Studies 1 and 2 examined behavioral intentions in response to a series of hypothetical scenarios; Studies 3 and 4 examined actual behavior in tests of mathematical and logical ability, and pointed to assumed partner's expectations as a potential mediator. The converging evidence supports the hypothesis that benevolent sexism encourages engagement in cross-gender helping relations that perpetuate traditional gender roles. (c) 2016 APA, all rights reserved).

Comparison of quartz crystallographic preferred orientations identified with optical fabric analysis, electron backscatter and neutron diffraction techniques.

PubMed

Hunter, N J R; Wilson, C J L; Luzin, V

2017-02-01

Three techniques are used to measure crystallographic preferred orientations (CPO) in a naturally deformed quartz mylonite: transmitted light cross-polarized microscopy using an automated fabric analyser, electron backscatter diffraction (EBSD) and neutron diffraction. Pole figure densities attributable to crystal-plastic deformation are variably recognizable across the techniques, particularly between fabric analyser and diffraction instruments. Although fabric analyser techniques offer rapid acquisition with minimal sample preparation, difficulties may exist when gathering orientation data parallel with the incident beam. Overall, we have found that EBSD and fabric analyser techniques are best suited for studying CPO distributions at the grain scale, where individual orientations can be linked to their source grain or nearest neighbours. Neutron diffraction serves as the best qualitative and quantitative means of estimating the bulk CPO, due to its three-dimensional data acquisition, greater sample area coverage, and larger sample size. However, a number of sampling methods can be applied to FA and EBSD data to make similar approximations. © 2016 The Authors Journal of Microscopy © 2016 Royal Microscopical Society.

Initial orienting towards sexually relevant stimuli: preliminary evidence from eye movement measures.

PubMed

Fromberger, Peter; Jordan, Kirsten; von Herder, Jakob; Steinkrauss, Henrike; Nemetschek, Rebekka; Stolpmann, Georg; Müller, Jürgen Leo

2012-08-01

It has been proposed that sexual stimuli will be processed in a comparable manner to other evolutionarily meaningful stimuli (such as spiders or snakes) and therefore elicit an attentional bias and more attentional engagement (Spiering and Everaerd, In E. Janssen (Ed.), The psychophysiology of sex (pp. 166-183). Bloomington: Indiana University Press, 2007). To investigate early and late attentional processes while looking at sexual stimuli, heterosexual men (n = 12) viewed pairs of sexually preferred (images of women) and sexually non-preferred images (images of girls, boys or men), while eye movements were measured. Early attentional processing (initial orienting) was assessed by the number of first fixations and late attentional processing (maintenance of attention) was assessed by relative fixation time. Results showed that relative fixation time was significantly longer for sexually preferred stimuli than for sexually non-preferred stimuli. Furthermore, the first fixation was more often directed towards the preferred sexual stimulus, when simultaneously presented with a non-sexually preferred stimulus. Thus, the current study showed for the first time an attentional bias to sexually relevant stimuli when presented simultaneously with sexually irrelevant pictures. This finding, along with the discovery that heterosexual men maintained their attention to sexually relevant stimuli, highlights the importance of investigating early and late attentional processes while viewing sexual stimuli. Furthermore, the current study showed that sexually relevant stimuli are favored by the human attentional system.

Fracture control of H-O engine components. [titanium tin alloy fuel pump impellers

NASA Technical Reports Server (NTRS)

Ryder, J. T.

1977-01-01

An investigation was made to obtain the material characterization and fatigue crack propagation data necessary to establish the salient characteristics of a Ti-6Al-2.5Sn(ELI) alloy fuel pump impeller to be used in a cryogenic service environment. Testing variables considered were: coupon orientation, frequency, load range ratio, and temperature. Data analysis correlated crack propagation data from conventional laboratory coupons with data from a parallel sided rotating disk used to model rotor stresses. Four major design recommendations when bore regions of fuel pump impellers to be operated in cryogenic environments are to be relatively highly stressed are discussed.

Measuring the preference towards patient-centred communication with the Chinese-revised Patient-Practitioner Orientation Scale: a cross-sectional study among physicians and patients in clinical settings in Shanghai, China.

PubMed

Wang, Jie; Zou, Runyu; Fu, Hua; Qian, Haihong; Yan, Yueren; Wang, Fan

2017-09-18

To adapt the Patient-Practitioner Orientation Scale (PPOS), to a Chinese context, and explore the preference towards patient-centred communication among physicians and patients with the Chinese-revised Patient-Practitioner Orientation Scale (CR-PPOS). A cross-sectional questionnaire-based study. Clinical settings from eight medical units, including four community hospitals and four general hospitals, in Shanghai, China. 1018 participants, including 187 physicians and 831 patients, completed this study in two successive stages. Psychometric properties of the CR-PPOS and participants' score on the CR-PPOS. Compared with the original PPOS, the 11-item CR-PPOS obtained better psychometric indices. Physicians and patients scored differently on both the total CR-PPOS and its two subscales. Compared with physicians, the scores of patients were more influenced by their personal characteristics, such as age and education. The CR-PPOS is a better instrument in a Chinese context than the original translated version. The divergence in the extent to which patient-centred communication is preferred among Chinese physicians and patients should be noted. Adapting physicians' communication strategy to patients' preferences based on their personal characteristics can be a viable approach towards improving clinical efficiency. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Effect of magnetic and electric coupling fields on micro- and nano- structure of carbon films in the CVD diamond process and their electron field emission property

NASA Astrophysics Data System (ADS)

Wang, Yijia; Li, Jiaxin; Hu, Naixiu; Jiang, Yunlu; Wei, Qiuping; Yu, Zhiming; Long, Hangyu; Zhu, Hekang; Xie, Youneng; Ma, Li; Lin, Cheng-Te; Su, Weitao

2018-03-01

In this paper, both electric field and magnetic field were used to assist the hot filament chemical vapor deposition (HFCVD) and we systematically investigated the effects of which on the (1) phase composition, (2) grain size, (3) thickness and (4) preferred orientation of diamond films through SEM, Raman and XRD. The application of magnetic field in electric field, so called ‘the magnetic and electric coupling fields’, enhanced the graphitization and refinement of diamond crystals, slowed down the decrease of film thickness along with the increase of bias current, and suppressed diamond (100) orientation. During the deposition process, the electric field provided additional energy to HFCVD system and generated large number of energetic particles which might annihilate at the substrate and lose kinetic energy, while the Lorentz force, provided by magnetic field, could constrict charged particles (including electrons) to do spiral movement, which prolonged their moving path and life, thus the system energy increased. With the graphitization of diamond films intensified, the preferred orientation of diamond films completely evolved from (110) to (100), until the orientation and diamond phase disappeared, which can be attributed to (I) the distribution and concentration ratio of carbon precursors (C2H2 and CH3) and (II) graphitization sequence of diamond crystal facets. Since the electron field emission property of carbon film is sensitive to the phase composition, thickness and preferred orientation, nano- carbon cones, prepared by the negative bias current of 20 mA and magnetic field strength of 80 Gauss, exhibited the lowest turn-on field of 6.1 V -1 μm-1.

Mineral resource of the month: tin

USGS Publications Warehouse

Carlin, James F.

2011-01-01

Tin was one of the earliest-known metals. Because of its hardening effect on copper, tin was used in bronze implements as early as 3500 B.C. Bronze, a copper-tin alloy that can be sharpened and is hard enough to retain a cutting edge, was used during the Bronze Age in construction tools as well as weapons for hunting and war. The geographical separation between tin-producing and tin-consuming nations greatly influenced the patterns of early trade routes. Historians think that as early as 1500 B.C., Phoenicians traveled by sea to the Cornwall district of England to obtain tin. The pure metal was not used unalloyed until about 600 B.C.

Tin recycling in the United States in 1998

USGS Publications Warehouse

Carlin, James F.

2001-01-01

This materials flow study includes a description of tin supply and demand factors for the United States to illustrate the extent of tin recycling and to identify recycling trends. Understanding the flow of materials from source to ultimate disposition can assist in improving the management of the use of natural resources in a manner that is compatible with sound environmental practices. The quantity of tin recycled in 1998 as a percentage of apparent tin supply was estimated to be about 22%, and recycling efficiency was estimated to be 75%. Of the total tin consumed in products for the U.S. market in 1998, an estimated 12% was consumed in products where the tin was not recyclable (dissipative uses).

Social Orienting and Attention Is Influenced by the Presence of Competing Nonsocial Information in Adolescents with Autism

PubMed Central

Unruh, Kathryn E.; Sasson, Noah J.; Shafer, Robin L.; Whitten, Allison; Miller, Stephanie J.; Turner-Brown, Lauren; Bodfish, James W.

2016-01-01

Background: Our experiences with the world play a critical role in neural and behavioral development. Children with autism spectrum disorder (ASD) spend a disproportionate amount of time seeking out, attending to, and engaging with aspects of their environment that are largely nonsocial in nature. In this study we adapted an established method for eliciting and quantifying aspects of visual choice behavior related to preference to test the hypothesis that preference for nonsocial sources of stimulation diminishes orientation and attention to social sources of stimulation in children with ASD. Method: Preferential viewing tasks can serve as objective measures of preference, with a greater proportion of viewing time to one item indicative of increased preference. The current task used gaze-tracking technology to examine patterns of visual orientation and attention to stimulus pairs that varied in social (faces) and nonsocial content (high autism interest or low autism interest). Participants included both adolescents diagnosed with ASD and typically developing; groups were matched on IQ and gender. Results: Repeated measures ANOVA revealed that individuals with ASD had a significantly greater latency to first fixate on social images when this image was paired with a high autism interest image, compared to a low autism interest image pairing. Participants with ASD showed greater total look time to objects, while typically developing participants preferred to look at faces. Groups also differed in number and average duration of fixations to social and object images. In the ASD group only, a measure of nonsocial interest was associated with reduced preference for social images when paired with high autism interest images. Conclusions: In ASD, the presence of nonsocial sources of stimulation can significantly increase the latency of look time to social sources of information. These results suggest that atypicalities in social motivation in ASD may be context-dependent, with a greater degree of plasticity than is assumed by existing social motivation accounts of ASD. PMID:28066169

76 FR 28426 - Applications for New Awards; Assistive Technology Act of 1998, as Amended (AT Act)-National...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-17

... (DUNS) number and a Taxpayer Identification Number (TIN); b. Register both your DUNS number and TIN with... DUNS number and TIN on your application; and d. Maintain an active CCR registration with current... obtain a TIN from the Internal Revenue Service. If you are an individual, you can obtain a TIN from the...

31 CFR 351.43 - Are taxpayer identification numbers (TINs) required for the registration of a definitive Series...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (TINs) required for the registration of a definitive Series EE savings bond? 351.43 Section 351.43 Money... Definitive Series EE Savings Bonds § 351.43 Are taxpayer identification numbers (TINs) required for the... must include the TIN of the owner or first-named coowner. The TIN of the second-named coowner or...

78 FR 42937 - Applications for New Awards; National Institute on Disability and Rehabilitation Research...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-18

... Number (TIN); b. Register both your DUNS number and TIN with the System for Award Management (SAM... your DUNS number and TIN on your application; and d. Maintain an active SAM registration with current... obtain a TIN from the Internal Revenue Service. If you are an individual, you can obtain a TIN from the...

77 FR 11190 - Yokohama Tire Company, Denial of Petition for Decision of Inconsequential Noncompliance

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-24

... (TIN)/partial TIN required by paragraph S5.5.1 on one of the tire sidewalls. YTC indicates that the noncompliant tires do however include the full TIN on the intended outboard sidewall. YTC argues that the TIN and the partial TIN are used to properly identify tires that are involved in a safety campaign. YTC...

26 CFR 31.3406(g)-1 - Exception for payments to certain payees and certain other payments.

Code of Federal Regulations, 2013 CFR

2013-04-01

... payee's TIN and the payee's TIN has been validated through the IRS TIN Matching Program; or (B) The QPCA... not constitute notice by the IRS that the payee's TIN is incorrect for purposes of section 3406(a)(1....) At the time of enrollment, Q obtains Merchant X's taxpayer identification number (TIN). Merchant X is...

31 CFR 351.43 - Are taxpayer identification numbers (TINs) required for the registration of a definitive Series...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (TINs) required for the registration of a definitive Series EE savings bond? 351.43 Section 351.43 Money... Definitive Series EE Savings Bonds § 351.43 Are taxpayer identification numbers (TINs) required for the... must include the TIN of the owner or first-named coowner. The TIN of the second-named coowner or...

31 CFR 351.43 - Are taxpayer identification numbers (TINs) required for the registration of a definitive Series...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (TINs) required for the registration of a definitive Series EE savings bond? 351.43 Section 351.43 Money... Definitive Series EE Savings Bonds § 351.43 Are taxpayer identification numbers (TINs) required for the... must include the TIN of the owner or first-named coowner. The TIN of the second-named coowner or...

78 FR 36755 - Applications for New Awards; National Institute on Disability and Rehabilitation Research...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-19

... Identification Number (TIN); b. Register both your DUNS number and TIN with the System for Award Management (SAM... your DUNS number and TIN on your application; and d. Maintain an active SAM registration with current... obtain a TIN from the Internal Revenue Service. If you are an individual, you can obtain a TIN from the...

78 FR 38958 - Applications for New Awards; National Institute on Disability and Rehabilitation Research...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-28

... Number (TIN); b. Register both your DUNS number and TIN with the System for Award Management (SAM... your DUNS number and TIN on your application; and d. Maintain an active SAM registration with current... obtain a TIN from the Internal Revenue Service. If you are an individual, you can obtain a TIN from the...

31 CFR 351.43 - Are taxpayer identification numbers (TINs) required for the registration of a definitive Series...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (TINs) required for the registration of a definitive Series EE savings bond? 351.43 Section 351.43 Money... Definitive Series EE Savings Bonds § 351.43 Are taxpayer identification numbers (TINs) required for the... must include the TIN of the owner or first-named coowner. The TIN of the second-named coowner or...

31 CFR 351.43 - Are taxpayer identification numbers (TINs) required for the registration of a definitive Series...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (TINs) required for the registration of a definitive Series EE savings bond? 351.43 Section 351.43 Money... Definitive Series EE Savings Bonds § 351.43 Are taxpayer identification numbers (TINs) required for the... must include the TIN of the owner or first-named coowner. The TIN of the second-named coowner or...

Reductive spectrophotometry of divalent tin sensitization on soda lime glass

NASA Astrophysics Data System (ADS)

Bejugam, Vinith; Wei, Xingfei; Roper, D. Keith

2016-07-01

Rapid and facile evaluation of tin (II) sensitization could lead to improved understanding of metal deposition in electroless (EL) plating. This report used a balanced redox reaction between 3,3‧,5,5‧-tetramethylbenzidine dihydrochloride (TMB-HCL) and N-bromosuccinimide (NBS) to evaluate effects of sensitization conditions (i.e., sensitization time, analyte concentration, aqueous immersion, and acid content) on the accumulated mass of surface-associated divalent tin ion. The accumulated mass of tin (II) increased as the sensitization time increased up to 30 s in proportion to aqueous tin (II) chloride concentrations between 2.6 and 26 mM at a trifluoroacetic acid (TFA) content of 68 mM. The average mass peaked at 7.3 nanomoles (nmol) per cm2 after a 5 s aqueous immersion post-sensitization, and then decreased with increasing aqueous immersion post-sensitization. The total average tin (II) + tin (IV) accumulated on soda lime glass measured by inductively coupled plasma optical emission spectrometry (ICP-OES) was 17% higher at 30 s sensitization, suggesting a fraction of the tin (II) present may have oxidized to tin (IV). These results indicated that in situ spectrophotometric evaluation of tin (II) could support development of EL plating for electronics, catalysis, and solar cells.

Van der Waals epitaxial growth of two-dimensional single-crystalline GaSe domains on graphene

DOE PAGES

Li, Xufan; Basile, Leonardo; Huang, Bing; ...

2015-07-22

Two-dimensional (2D) van der Waals (vdW) heterostructures are a family of artificially-structured materials that promise tunable optoelectronic properties for devices with enhanced functionalities. Compared to stamping, direct epitaxy of vdW heterostructures is ideal for clean interlayer interfaces and scalable device fabrication. Here, we explore the synthesis and preferred orientations of 2D GaSe atomic layers on graphene (Gr) by vdW epitaxy. Guided by the wrinkles on graphene, GaSe nuclei form that share a predominant lattice orientation. Due to vdW epitaxial growth many nuclei grow as perfectly aligned crystals and coalesce to form large (tens of microns), single-crystal flakes. Through theoretical investigationsmore » of interlayer energetics, and measurements of preferred orientations by atomic-resolution STEM and electron diffraction, a 10.9 interlayer rotation of the GaSe lattice with respect to the underlying graphene is found to be the most energetically preferred vdW heterostructure with the largest binding energy and the longest-range ordering. These GaSe/Gr vdW heterostructures exhibit an enhanced Raman E 2 1g band of monolayer GaSe along with highly-quenched photoluminescence due to strong charge transfer. Despite the very large lattice mismatch of GaSe/Gr through vdW epitaxy, the predominant orientation control and convergent formation of large single-crystal flakes demonstrated here is promising for the scalable synthesis of large-area vdW heterostructures for the development of new optical and optoelectronic devices.« less

Van der Waals epitaxial growth of two-dimensional single-crystalline GaSe domains on graphene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Xufan; Basile, Leonardo; Huang, Bing

Two-dimensional (2D) van der Waals (vdW) heterostructures are a family of artificially-structured materials that promise tunable optoelectronic properties for devices with enhanced functionalities. Compared to stamping, direct epitaxy of vdW heterostructures is ideal for clean interlayer interfaces and scalable device fabrication. Here, we explore the synthesis and preferred orientations of 2D GaSe atomic layers on graphene (Gr) by vdW epitaxy. Guided by the wrinkles on graphene, GaSe nuclei form that share a predominant lattice orientation. Due to vdW epitaxial growth many nuclei grow as perfectly aligned crystals and coalesce to form large (tens of microns), single-crystal flakes. Through theoretical investigationsmore » of interlayer energetics, and measurements of preferred orientations by atomic-resolution STEM and electron diffraction, a 10.9 interlayer rotation of the GaSe lattice with respect to the underlying graphene is found to be the most energetically preferred vdW heterostructure with the largest binding energy and the longest-range ordering. These GaSe/Gr vdW heterostructures exhibit an enhanced Raman E 2 1g band of monolayer GaSe along with highly-quenched photoluminescence due to strong charge transfer. Despite the very large lattice mismatch of GaSe/Gr through vdW epitaxy, the predominant orientation control and convergent formation of large single-crystal flakes demonstrated here is promising for the scalable synthesis of large-area vdW heterostructures for the development of new optical and optoelectronic devices.« less

Thermo-orientation and the movement of feather-feeding lice on hosts.

PubMed

Harbison, Christopher W; Boughton, Rachel M

2014-08-01

Temperature variation on the host is known to influence ectoparasite distributions. Ectoparasites may also use temperature gradients between host regions when moving on the host; however, tests are rare. Feather-feeding wing lice (Phthiraptera: Ischnocera) spend the majority of their time on the flight feathers of their avian hosts where they insert their bodies between feather barbs to escape host preening. However, because wing lice feed on downy abdominal feathers, they must repeatedly migrate between the flight feathers and body regions of their hosts. We performed a series of experiments that tested thermo-orientation in wing lice and evaluated its potential use during louse migrations between host regions. We found that wing lice can rapidly and accurately locate nearby heat targets that approximate host temperatures (37 C), demonstrating a capacity for directed thermo-orientation. We next tested the preference of wing lice for temperatures found along migration routes between bird flight feathers and their body regions. Wing lice could distinguish between temperatures found within distinct bird regions, and lice that had recently fed preferred the cooler temperatures (32 C), similar to those within bird flight feathers where they typically reside. However, when starved for 18-20 hr, wing lice shifted their preferences toward temperatures typical of bird body regions where they feed (36 C), demonstrating an ability to use thermal cues when moving between bird regions. We discuss the use of thermal cues during louse migration and microhabitat selection, as well as other potential impacts of thermo-orientation on host-parasite interactions.

[Vulvar plethysmographic findings in transsexual women].

PubMed

Tichý, P

1994-05-02

Transsexualism is a complicated diagnostic category. From the differential diagnostic aspect it is necessary, among others, to rule out homosexuality. The objective of the present work was to express objectively vulvo-plethysmographic reactions in transsexual women and to assess whether (or how) these reactions differ from findings in women with a homosexual orientation and to evaluate subsequently possibilities of vulvo-plethysmography in the differential diagnosis of homosexuality and transsexualism. Using an electro-capacitance vulvo-plethysmographic apparatus (designed by Figar et al.), 25 women (mean age 27.6 years, range 18-39 years) with an inverse sexual orientation--transsexuals--were examined. The results were compared with a group of 50 women, matched for age, who reported a homosexual orientation. On evaluation of the total number of recorded positive reactions to heterosexual and homosexual categories of exposed erotic stimuli the difference between the two groups on projection of 3 from 4 categories of these stimuli was highly significant (p < 0.001, chi 2 test). The differences were revealed in particular when evaluating preferences of pictures of sexual activities of partners. While in homosexually oriented women, as expected, preference of homosexual activities was recorded (74%) or a not clear-cut differentiation of these stimuli (26%), in 88% of transsexual women there was a more or less markedly expressed preference of heterosexual activities. Significant differences were found in results of vulvo-plethysmographic examinations of transsexual and homosexual women. This confirmed the expedience of using electro-capacitance vulvo-plethysmography for the differential diagnosis of homosexual and transsexual women.

An Investigation of Turkish Middle School Science Teachers' Pedagogical Orientations Towards Direct and Inquiry Instructional Approaches

NASA Astrophysics Data System (ADS)

Sahingoz, Selcuk

One of the most important goals of science education is preparing effective science teachers which includes the development of a science pedagogical orientation. Helping in-service science teachers improve their orientations toward science teaching begins with identifying their current orientations. While there are many aspects of an effective science teaching orientation, this study specifically focuses on effective pedagogy. The interest of this study is to clarify pedagogical orientations of middle school science teachers in Turkey toward the teaching of science conceptual knowledge. It focuses on what instructional preferences Turkish middle school science teachers have in theory and practice. The purpose of this study is twofold: 1) to elucidate teacher pedagogical profiles toward direct and inquiry instructional approaches. For this purpose, quantitative profile data, using a Turkish version of the Pedagogy of Science Teaching Test (POSTT-TR) assessment instrument, was collected from 533 Turkish middle school science teachers; 2) to identify teaching orientations of middle school science teachers and to identify their reasons for preferring specific instructional practices. For this purpose, descriptive qualitative, interview data was collected from 23 teachers attending a middle school science teacher workshop in addition to quantitative data using the POSTT-TR. These teachers sat for interviews structured by items from the POSTT-TR. Thus, the research design is mixed-method. The design provides a background profile on teacher orientations along with insights on reasons for pedagogical choices. The findings indicate that instructional preference distributions for the large group and smaller group are similar; however, the smaller workshop group is more in favor of inquiry instructional approaches. The findings also indicate that Turkish middle school science teachers appear to have variety of teaching orientations and they have varied reasons. Moreover, the research found that several contextual factors contributed to teachers' instructional practices including internal and external issues such as school environment, limited resources, large class sizes, standardized test pressure, and limited accessibility to professional development. The findings provide insight on the readiness of middle school teachers to implement the Turkish Curriculum Framework, specifically, teacher readiness to put science inquiry instructional approaches into actual classroom practice. Given that new Turkish policy calls for greater inquiry instruction, this study can help inform teacher development efforts directed at promoting science inquiry instruction.

The do re mi's of everyday life: the structure and personality correlates of music preferences.

PubMed

Rentfrow, Peter J; Gosling, Samuel D

2003-06-01

The present research examined individual differences in music preferences. A series of 6 studies investigated lay beliefs about music, the structure underlying music preferences, and the links between music preferences and personality. The data indicated that people consider music an important aspect of their lives and listening to music an activity they engaged in frequently. Using multiple samples, methods, and geographic regions, analyses of the music preferences of over 3,500 individuals converged to reveal 4 music-preference dimensions: Reflective and Complex, Intense and Rebellious, Upbeat and Conventional, and Energetic and Rhythmic. Preferences for these music dimensions were related to a wide array of personality dimensions (e.g., Openness), self-views (e.g., political orientation), and cognitive abilities (e.g., verbal IQ).

Culture and first-person pronouns.

PubMed

Na, Jinkyung; Choi, Incheol

2009-11-01

Priming research has shown that repeated exposures to first-person singular pronouns (I, my, me, mine) activate an individualistic orientation, whereas first-person plural pronouns (we, our, us, ours) activate a collectivistic orientation. However, little research has been done to explore the opposite direction of influence such that one's cultural orientation determines one's choice between first-person singular versus plural pronouns. The authors conducted three studies to examine the effects of one's cultural orientation on one's use of first-person possessive pronouns. Results show that, compared to their individualistic counterparts, participants who have a collectivistic orientation, chronically or temporarily by priming, preferred to use first-person plural possessive pronouns.

Corrosion Behavior of Carbon Steel in Concrete Material Composed of Tin Slag Waste in Aqueous Chloride Solution

NASA Astrophysics Data System (ADS)

Rustandi, Andi; Cahyadi, Agung; Taruli Siallagan, Sonia; Wafa' Nawawi, Fuad; Pratesa, Yudha

2018-01-01

Tin slag is a byproduct of tin ore smelting process which is rarely utilized. The main purpose of this work is to investigate the use of tin slag for concrete cement material application compared to the industrial Ordinary Portland Cement (OPC). Tin slag composition was characterized by XRD and XRF analysis. The characterization results showed the similar chemical composition of tin slag and OPC. It also revealed the semi crystalline structure of tin slag sample. Several electrochemical tests were performed to evaluate corrosion behavior of tin slag, OPC and various mixed composition of both materials and the addition of CaO. The corrosion behavior of OPC and tin slag were evaluated by using Cyclic Polarization, Electrochemical Impedance Spectroscopy (EIS) and Electrochemical Frequency Modulation (EFM) methods. Aqueous sodium chloride (NaCl) solution with 3.5% w.t concentration which similar to seawater was used as the electrolyte in this work. The steel specimen used as the reinforce bar (rebar) material of the concrete was carbon steel AISI 1045. The rebar was embedded in the concrete cement which composed of OPC and the various composition of tin slag including slag without addition of CaO and slag mixed with addition of 50 % CaO. The electrochemical tests results revealed that tin slag affected its corrosion behavior which becoming more active and increasing the corrosion rate as well as decreasing the electrochemical impedance.

Sleep-wake habits and circadian preference in Mexican secondary school.

PubMed

Arrona-Palacios, Arturo; García, Aída; Valdez, Pablo

2015-10-01

The current study aimed to determine the differences between sleep-wake habits and circadian preference in Mexican adolescents attending classes at a morning shift or an afternoon shift. The sample consisted of 568 students of a secondary school in Reynosa, northeastern Mexico, of whom 280 were boys and 288 were girls (mean age 14.08 ± 0.72 years, age range 13-16 years). In the morning shift, 287 students attend classes on a schedule from 7:30 to 13:00 and the afternoon shift, 281 students, on a schedule from 13:20 to 19:00. Students completed a general information questionnaire, the Sleep Timing Questionnaire and the Spanish version of the Morningness-Eveningness Questionnaire. The adolescents who attended the morning shift had earlier bedtime and waking time, but shorter sleep duration than those who attended the afternoon shift. Those oriented to eveningness had later bedtime, waking time, and a shorter sleep duration than those oriented to morningness. Two interactions were found between school shift and chronotype. First, with regard to waking time during weekdays, students who attended the afternoon shift and were oriented to eveningness woke up later than those who attended the morning shift and were oriented to eveningness; during weekdays, there were no differences between the waking time of morning-type and evening-type students who attended the morning shift. Second, with regard to sleep duration on weekdays, students who attended the morning shift and were oriented to eveningness had the shortest sleep duration. Furthermore, there were no differences between sleep duration on weekdays in evening-type and morning-type students of the afternoon shift. Adolescents who attend classes in the morning shift and are oriented to eveningness are the most sleep deprived. Those who attend the afternoon shift will have optimal sleep duration, regardless of their circadian preference. Copyright © 2015 Elsevier B.V. All rights reserved.

Low temperature processed complementary metal oxide semiconductor (CMOS) device by oxidation effect from capping layer.

PubMed

Wang, Zhenwei; Al-Jawhari, Hala A; Nayak, Pradipta K; Caraveo-Frescas, J A; Wei, Nini; Hedhili, M N; Alshareef, H N

2015-04-20

In this report, both p- and n-type tin oxide thin-film transistors (TFTs) were simultaneously achieved using single-step deposition of the tin oxide channel layer. The tuning of charge carrier polarity in the tin oxide channel is achieved by selectively depositing a copper oxide capping layer on top of tin oxide, which serves as an oxygen source, providing additional oxygen to form an n-type tin dioxide phase. The oxidation process can be realized by annealing at temperature as low as 190 °C in air, which is significantly lower than the temperature generally required to form tin dioxide. Based on this approach, CMOS inverters based entirely on tin oxide TFTs were fabricated. Our method provides a solution to lower the process temperature for tin dioxide phase, which facilitates the application of this transparent oxide semiconductor in emerging electronic devices field.

Corrosion resistance and mechanical properties of titanium nitride plating on orthodontic wires.

PubMed

Sugisawa, Haruki; Kitaura, Hideki; Ueda, Kyosuke; Kimura, Keisuke; Ishida, Masahiko; Ochi, Yumiko; Kishikawa, Akiko; Ogawa, Saika; Takano-Yamamoto, Teruko

2018-03-30

Titanium nitride (TiN) coating by ion plating has properties such as high hardness, wear resistance, corrosion resistance, and surface lubricity, therefore TiN coating is often used in various dental appliances and materials. In this study, we evaluated the corrosion behaviors and mechanical properties of TiN coated stainless steel (SS) and nickel titanium (Ni-Ti) orthodontic wires prepared by ion plating. TiN coating by ion plating improves the corrosion resistance of orthodontic wires. The corrosion pitting of the TiN coated wire surface become small. The tensile strength and stiffness of SS wire were increased after TiN coating. In contrast, its elastic force, which is a property for Ni-Ti wire, was decreased. In addition, TiN coating provided small friction forces. The low level of friction may increase tooth movement efficiently. Therefore, TiN coated SS wire could be useful for orthodontics treatment.

Low Temperature Processed Complementary Metal Oxide Semiconductor (CMOS) Device by Oxidation Effect from Capping Layer

PubMed Central

Wang, Zhenwei; Al-Jawhari, Hala A.; Nayak, Pradipta K.; Caraveo-Frescas, J. A.; Wei, Nini; Hedhili, M. N.; Alshareef, H. N.

2015-01-01

In this report, both p- and n-type tin oxide thin-film transistors (TFTs) were simultaneously achieved using single-step deposition of the tin oxide channel layer. The tuning of charge carrier polarity in the tin oxide channel is achieved by selectively depositing a copper oxide capping layer on top of tin oxide, which serves as an oxygen source, providing additional oxygen to form an n-type tin dioxide phase. The oxidation process can be realized by annealing at temperature as low as 190°C in air, which is significantly lower than the temperature generally required to form tin dioxide. Based on this approach, CMOS inverters based entirely on tin oxide TFTs were fabricated. Our method provides a solution to lower the process temperature for tin dioxide phase, which facilitates the application of this transparent oxide semiconductor in emerging electronic devices field. PMID:25892711

The Prognostic Value of Tumor-Infiltrating Neutrophils in Gastric Adenocarcinoma after Resection

PubMed Central

Wang, Wei; Chen, Ju-gao; Wu, Yan-heng; Lv, Lin; Li, Jian-jun; Chen, Yi-bing; Wang, Dan-dan; Pan, Qiu-zhong; Li, Xiao-dong; Xia, Jian-chuan

2012-01-01

Background Several pieces of evidence indicate that tumor-infiltrating neutrophils (TINs) are correlated to tumor progression. In the current study, we explore the relationship between TINs and clinicopathological features of gastric adenocarcinoma patients. Furthermore, we investigated the prognostic value of TINs. Patients and Methods The study was comprised of two groups, training group (115 patients) and test group (97 patients). Biomarkers (intratumoral CD15+ neutrophils) were assessed by immunohistochemistry. The relationship between clinicopathological features and patient outcome were evaluated using Cox regression and Kaplan-Meier analysis. Results Immunohistochemical detection showed that the tumor-infiltrating neutrophils (TINs) in the training group ranged from 0.00–115.70 cells/high-power microscopic field (HPF) and the median number was 21.60 cells/HPF. Based on the median number, the patients were divided into high and low TINs groups. Chi-square test analysis revealed that the density of CD15+ TINs was positively associated with lymph node metastasis (p = 0.024), distance metastasis (p = 0.004) and UICC (International Union Against Cancer) staging (p = 0.028). Kaplan-Meier analysis showed that patients with a lower density of TINs had a better prognosis than patients with a higher density of TINs (p = 0.002). Multivariate Cox's analysis showed that the density of CD15+ TINs was an independent prognostic factor for overall survival of gastric adenocarcinoma patients. Using another 97 patients as a test group and basing on the median number of TINs (21.60 cells/HPF) coming from the training group, Kaplan-Meier analysis also showed that patients with a lower density of TINs had a better prognosis than patients with a higher density of TINs (p = 0.032). The results verify that the number of CD15+ TINs can predict the survival of gastric adenocarcinoma surgical patients. Conclusions The presence of CD15+ TINs is an independent and unfavorable factor in the prognosis of gastric adenocarcinoma patients. Targeting CD15+ TINs may be a potential intervenient therapy in the future. PMID:22442706

Canopy architectural and physiological characterization of near-isogenic wheat lines differing in the tiller inhibition gene tin.

PubMed

Moeller, Carina; Evers, Jochem B; Rebetzke, Greg

2014-01-01

Tillering is a core constituent of plant architecture, and influences light interception to affect plant and crop performance. Near-isogenic lines (NILs) varying for a tiller inhibition (tin) gene and representing two genetic backgrounds were investigated for tillering dynamics, organ size distribution, leaf area, light interception, red: far-red ratio, and chlorophyll content. Tillering ceased earlier in the tin lines to reduce the frequencies of later primary and secondary tillers compared to the free-tillering NILs, and demonstrated the genetically lower tillering plasticity of tin-containing lines. The distribution of organ sizes along shoots varied between NILs contrasting for tin. Internode elongation commenced at a lower phytomer, and the peduncle was shorter in the tin lines. The flag leaves of tin lines were larger, and the longest leaf blades were observed at higher phytomers in the tin than in free-tillering lines. Total leaf area was reduced in tin lines, and non-tin lines invested more leaf area at mid-canopy height. The tiller economy (ratio of seed-bearing shoots to numbers of shoots produced) was 10% greater in the tin lines (0.73-0.76) compared to the free-tillering sisters (0.62-0.63). At maximum tiller number, the red: far-red ratio (light quality stimulus that is thought to induce the cessation of tillering) at the plant-base was 0.18-0.22 in tin lines and 0.09-0.11 in free-tillering lines at levels of photosynthetic active radiation of 49-53% and 30-33%, respectively. The tin lines intercepted less radiation compared to their free-tillering sisters once genotypic differences in tiller numbers had established, and maintained green leaf area in the lower canopy later into the season. Greater light extinction coefficients (k) in tin lines prior to, but reduced k after, spike emergence indicated that differences in light interception between NILs contrasting in tin cannot be explained by leaf area alone but that geometric and optical canopy properties contributed. The careful characterization of specifically-developed NILs is refining the development of a physiology-based model for tillering to improve understanding of the value of architectural traits for use in cereal improvement.

Tumor-infiltrating neutrophils predict benefit from adjuvant chemotherapy in patients with muscle invasive bladder cancer.

PubMed

Zhou, Lin; Xu, Le; Chen, Lingli; Fu, Qiang; Liu, Zheng; Chang, Yuan; Lin, Zongming; Xu, Jiejie

2017-01-01

Growing evidence shows tumor-infiltrating neutrophils (TINs) involvement in tumorigenesis. The objective of this study is to assess the prognostic effect of TINs and its impact on adjuvant chemotherapy benefits in muscle invasive bladder cancer (MIBC). A total of 142 MIBC patients from Zhongshan Hospital, 119 MIBC patients from FUSCC, and 405 MIBC patients from TCGA cohort were enrolled in the study. TINs were evaluated by immunohistochemical staining of CD66b or the CIBERSORT method. Patients with high TINs had a significantly poorer overall survival ( p = 0.001, p < 0.001, and p = 0.002, respectively) in the three sets. In the multivariate analysis, the presence of high TINs (HR = 2.122, p = 0.007; HR = 3.807, p < 0.001; HR = 2.104, p = 0.001; respectively) was identified as an independent prognostic factor for overall survival in the three sets. More importantly, Low TINs patients had significantly longer overall survival in patients without ACT in the three sets. Gene set enrichment analysis showed that lymphocyte activation ( p < 0.001) and T cell activation ( p = 0.008) were significantly enriched in the low TINs group. In addition, TINs were negatively correlated with CD8 + T cells, suggesting that the status of high-TINs was linked to the status of immunosuppression in MIBC. TINs could be used as independent prognostic factor. Low TINs identified a subgroup of MIBC patients who appeared to benefit from adjuvant chemotherapy. Incorporation of TINs into TNM system could further stratify patients with different prognosis.

Tumor-infiltrating neutrophils predict benefit from adjuvant chemotherapy in patients with muscle invasive bladder cancer

PubMed Central

Zhou, Lin; Xu, Le; Chen, Lingli; Fu, Qiang; Liu, Zheng; Chang, Yuan; Lin, Zongming; Xu, Jiejie

2017-01-01

ABSTRACT Growing evidence shows tumor-infiltrating neutrophils (TINs) involvement in tumorigenesis. The objective of this study is to assess the prognostic effect of TINs and its impact on adjuvant chemotherapy benefits in muscle invasive bladder cancer (MIBC). A total of 142 MIBC patients from Zhongshan Hospital, 119 MIBC patients from FUSCC, and 405 MIBC patients from TCGA cohort were enrolled in the study. TINs were evaluated by immunohistochemical staining of CD66b or the CIBERSORT method. Patients with high TINs had a significantly poorer overall survival (p = 0.001, p < 0.001, and p = 0.002, respectively) in the three sets. In the multivariate analysis, the presence of high TINs (HR = 2.122, p = 0.007; HR = 3.807, p < 0.001; HR = 2.104, p = 0.001; respectively) was identified as an independent prognostic factor for overall survival in the three sets. More importantly, Low TINs patients had significantly longer overall survival in patients without ACT in the three sets. Gene set enrichment analysis showed that lymphocyte activation (p < 0.001) and T cell activation (p = 0.008) were significantly enriched in the low TINs group. In addition, TINs were negatively correlated with CD8+ T cells, suggesting that the status of high-TINs was linked to the status of immunosuppression in MIBC. TINs could be used as independent prognostic factor. Low TINs identified a subgroup of MIBC patients who appeared to benefit from adjuvant chemotherapy. Incorporation of TINs into TNM system could further stratify patients with different prognosis. PMID:28507798

A comparative study of fine polished stainless steel, TiN and TiN/Ag surfaces: adhesion and attachment strength of Listeria monocytogenes as well as anti-listerial effect.

PubMed

Skovager, Anne; Whitehead, Kathryn; Wickens, David; Verran, Joanna; Ingmer, Hanne; Arneborg, Nils

2013-09-01

Magnetron sputtering was used to produce nanocomposite TiN and TiN/Ag coatings on stainless steel surfaces. The surface chemistry (EDX), physicochemical properties (contact angles), topography and roughness parameters (WLP and AFM) of the fine polished stainless steel (FPSS), TiN and TiN/8.6 at.% Ag surfaces were examined. Real-time initial adhesion of two Listeria monocytogenes strains (EGDe and 64) to the three surfaces was determined under flow conditions, and their attachment strength after adhesion was measured using atomic force microscopy (AFM). The anti-listerial properties of the surfaces were determined using LIVE/DEAD staining. Our results demonstrate that FPSS, TiN and TiN/8.6 at.% Ag possessed different surface properties, which may influence both attachment strength and anti-listerial properties. There were no significant (p>0.05) differences in the initial adhesion of the two L. monocytogenes strains to the three different surfaces. Attachment studies showed that the two L. monocytogenes strains did not attach to FPSS under wetted conditions. However, both strains attached to TiN and TiN/8.6 at.% Ag surfaces, although with less strength to TiN/8.6 at.% Ag than to TiN surfaces. The TiN/8.6 at.% Ag surface showed marked anti-listerial properties as compared with FPSS and TiN. Initial adhesion, attachment strength and anti-listerial properties were found to be strain dependent. Copyright © 2013 Elsevier B.V. All rights reserved.

THE TASTE OF SUGARS

PubMed Central

McCaughey, Stuart A.

2008-01-01

Sugars evoke a distinctive perceptual quality (“sweetness” in humans) and are generally highly preferred. The neural basis for these phenomena is reviewed for rodents, in which detailed electrophysiological measurements have been made. A receptor has been identified that binds sweeteners and activates G-protein-mediated signaling in taste receptor cells, which leads to changes in neural firing rates in the brain, where perceptions of taste quality, intensity, and palatability are generated. Most cells in gustatory nuclei are broadly-tuned, so quality perception presumably arises from patterns of activity across neural populations. However, some manipulations affect only the most sugar-oriented cells, making it useful to consider them as a distinct neural subtype. Quality perception may also arise partly due to temporal patterns of activity to sugars, especially within sugar-oriented cells that give large but delayed responses. Non-specific gustatory neurons that are excited by both sugars and unpalatable stimuli project to ventral forebrain areas, where neural responses provide a closer match with behavioral preferences. This transition likely involves opposing excitatory and inhibitory influences by different subgroups of gustatory cells. Sweeteners are generally preferred over water, but the strength of this preference can vary across time or between individuals, and higher preferences for sugars are often associated with larger taste-evoked responses. PMID:18499254

Effects of Implied Motion and Facing Direction on Positional Preferences in Single-Object Pictures.

PubMed

Palmer, Stephen E; Langlois, Thomas A

2017-07-01

Palmer, Gardner, and Wickens studied aesthetic preferences for pictures of single objects and found a strong inward bias: Right-facing objects were preferred left-of-center and left-facing objects right-of-center. They found no effect of object motion (people and cars showed the same inward bias as chairs and teapots), but the objects were not depicted as moving. Here we measured analogous inward biases with objects depicted as moving with an implied direction and speed by having participants drag-and-drop target objects into the most aesthetically pleasing position. In Experiment 1, human figures were shown diving or falling while moving forward or backward. Aesthetic biases were evident for both inward-facing and inward-moving figures, but the motion-based bias dominated so strongly that backward divers or fallers were preferred moving inward but facing outward. Experiment 2 investigated implied speed effects using images of humans, horses, and cars moving at different speeds (e.g., standing, walking, trotting, and galloping horses). Inward motion or facing biases were again present, and differences in their magnitude due to speed were evident. Unexpectedly, faster moving objects were generally preferred closer to frame center than slower moving objects. These results are discussed in terms of the combined effects of prospective, future-oriented biases, and retrospective, past-oriented biases.

Effect of Solvent and Substrate on the Surface Binding Mode of Carboxylate-Functionalized Aromatic Molecules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Domenico, Janna; Foster, Michael E.; Spoerke, Erik D.

Here, the efficiency of dye-sensitized solar cells (DSSCs) is strongly influenced by dye molecule orientation and interactions with the substrate. Understanding the factors controlling the surface orientation of sensitizing organic molecules will aid in the improvement of both traditional DSSCs and other devices that integrate molecular linkers at interfaces. Here, we describe a general approach to understand relative dye–substrate orientation and provide analytical expressions predicting orientation. We consider the effects of substrate, solvent, and protonation state on dye molecule orientation. In the absence of solvent, our model predicts that most carboxylic acid-functionalized molecules prefer to lie flat (parallel) on themore » surface, due to van der Waals interactions, as opposed to a tilted orientation with respect to the surface that is favored by covalent bonding of the carboxylic acid group to the substrate. When solvation effects are considered, however, the molecules are predicted to orient perpendicular to the surface. We extend this approach to help understand and guide the orientation of metal–organic framework (MOF) thin-film growth on various metal–oxide substrates. A two-part analytical model is developed on the basis of the results of DFT calculations and ab initio MD simulations that predicts the binding energy of a molecule by chemical and dispersion forces on rutile and anatase TiO 2 surfaces, and quantifies the dye solvation energy for two solvents. The model is in good agreement with the DFT calculations and enables rapid prediction of dye molecule and MOF linker binding preference on the basis of the size of the adsorbing molecule, identity of the surface, and the solvent environment. We establish the threshold molecular size, governing dye molecule orientation, for each condition.« less

Effect of Solvent and Substrate on the Surface Binding Mode of Carboxylate-Functionalized Aromatic Molecules

DOE PAGES

Domenico, Janna; Foster, Michael E.; Spoerke, Erik D.; ...

2018-04-25

Here, the efficiency of dye-sensitized solar cells (DSSCs) is strongly influenced by dye molecule orientation and interactions with the substrate. Understanding the factors controlling the surface orientation of sensitizing organic molecules will aid in the improvement of both traditional DSSCs and other devices that integrate molecular linkers at interfaces. Here, we describe a general approach to understand relative dye–substrate orientation and provide analytical expressions predicting orientation. We consider the effects of substrate, solvent, and protonation state on dye molecule orientation. In the absence of solvent, our model predicts that most carboxylic acid-functionalized molecules prefer to lie flat (parallel) on themore » surface, due to van der Waals interactions, as opposed to a tilted orientation with respect to the surface that is favored by covalent bonding of the carboxylic acid group to the substrate. When solvation effects are considered, however, the molecules are predicted to orient perpendicular to the surface. We extend this approach to help understand and guide the orientation of metal–organic framework (MOF) thin-film growth on various metal–oxide substrates. A two-part analytical model is developed on the basis of the results of DFT calculations and ab initio MD simulations that predicts the binding energy of a molecule by chemical and dispersion forces on rutile and anatase TiO 2 surfaces, and quantifies the dye solvation energy for two solvents. The model is in good agreement with the DFT calculations and enables rapid prediction of dye molecule and MOF linker binding preference on the basis of the size of the adsorbing molecule, identity of the surface, and the solvent environment. We establish the threshold molecular size, governing dye molecule orientation, for each condition.« less

The effect of synaptic plasticity on orientation selectivity in a balanced model of primary visual cortex

PubMed Central

Gonzalo Cogno, Soledad; Mato, Germán

2015-01-01

Orientation selectivity is ubiquitous in the primary visual cortex (V1) of mammals. In cats and monkeys, V1 displays spatially ordered maps of orientation preference. Instead, in mice, squirrels, and rats, orientation selective neurons in V1 are not spatially organized, giving rise to a seemingly random pattern usually referred to as a salt-and-pepper layout. The fact that such different organizations can sharpen orientation tuning leads to question the structural role of the intracortical connections; specifically the influence of plasticity and the generation of functional connectivity. In this work, we analyze the effect of plasticity processes on orientation selectivity for both scenarios. We study a computational model of layer 2/3 and a reduced one-dimensional model of orientation selective neurons, both in the balanced state. We analyze two plasticity mechanisms. The first one involves spike-timing dependent plasticity (STDP), while the second one considers the reconnection of the interactions according to the preferred orientations of the neurons. We find that under certain conditions STDP can indeed improve selectivity but it works in a somehow unexpected way, that is, effectively decreasing the modulated part of the intracortical connectivity as compared to the non-modulated part of it. For the reconnection mechanism we find that increasing functional connectivity leads, in fact, to a decrease in orientation selectivity if the network is in a stable balanced state. Both counterintuitive results are a consequence of the dynamics of the balanced state. We also find that selectivity can increase due to a reconnection process if the resulting connections give rise to an unstable balanced state. We compare these findings with recent experimental results. PMID:26347615

Tin recovery from tin slag using electrolysis method

NASA Astrophysics Data System (ADS)

Jumari, Arif; Purwanto, Agus; Nur, Adrian; Budiman, Annata Wahyu; Lerian, Metty; Paramita, Fransisca A.

2018-02-01

The process in industry, including in mining industry, would surely give negative effect such as waste polluting to the environment. Some of waste could be potentially reutilized to be a commodity with the higher economic value. Tin slag is one of them. The aim of this research was to recover the tin contained in tin slag. Before coming to the electrolysis, tin slag must be treated by dissolution. The grinded tin slag was dissolved into HCl solution to form a slurry. During dissolution, the slurry was agitated and heated, and finally filtered. The filtrate obtained was then electrolyzed. During the process of electrolysis, solid material precipitated on the used cathode. The precipitated solid was then separated and dried. The solid was then analyzed using XRD, XRF and SEM. The XRD analysis showed that the longest time of dissolution and electrolysis the highest the purity obtained in the product. The SEM analysis showed that the longest time of electrolysis the smallest tin particle obtained. Optimum time achieved in this research was 2 hours for the recovering time and 3 hours for the electrolysis time, with 9% tin recovered.

Transcription instability in high-risk neuroblastoma is associated with a global perturbation of chromatin domains.

PubMed

Zanon, Carlo; Tonini, Gian Paolo

2017-11-01

Chromosome instability has a pivotal role among the hallmarks of cancer, but its transcriptional counterpart is rarely considered a relevant factor in cell destabilization. To examine transcription instability (TIN), we first devised a metric we named TIN index and used it to evaluate TIN on a dataset containing more than 500 neuroblastoma samples. We found that metastatic tumors from high-risk (HR) patients are characterized by significantly different TIN index values compared to low/intermediate-risk patients. Our results indicate that the TIN index is a good predictor of neuroblastoma patient's outcome, and a related TIN index gene signature (TIN-signature) is also able to predict the neuroblastoma patient's outcome with high confidence. Interestingly, we find that TIN-signature genes have a strong positional association with superenhancers in neuroblastoma tumors. Finally, we show that TIN is linked to chromatin structural domains and interferes with their integrity in HR neuroblastoma patients. This novel approach to gene expression analysis broadens the perspective of genome instability investigations to include functional aspects. © 2017 The Authors. Published by FEBS Press and John Wiley & Sons Ltd.

Highly conducting and preferred <220> oriented boron doped nc–Si films for window layers in nc–Si solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mondal, Praloy; Das, Debajyoti, E-mail: erdd@iacs.res.in

2016-05-23

Growth and optimization of the boron dopednanocrystalline silicon (nc-Si) films have been studied by varyingthe gaspressure applied to the hydrogendiluted silane plasma in RF (13.56 MHz) plasma-enhanced chemical vapor deposition (PECVD) system, using diborane (B{sub 2}H{sub 6}) as the dopant gas. High magnitudeof electrical conductivity (~10{sup 2} S cm{sup −1}) and<220>orientedcrystallographic lattice planes have been obtained with high crystalline volume fraction (~86 %) at an optimum pressure of 2.5 Torr. XRD and Raman studies reveal good crystallinity with preferred orientation, suitable for applications in stacked layer devices, particularly in nc–Si solar cells.

Black/white outdoor recreation preferences and participation: Illinois State Parks

Treesearch

John F. Dwyer; Paul H. Gobster

1992-01-01

Black/white comparisons of outdoor recreation preferences and behavior from a statewide survey identify a significantly greater black orientation to “developed sites” and “social interaction.” Strategies are recommended to enhance outdoor recreation opportunities for blacks, and long-term research needs are identified.

Mineral of the month: tin

USGS Publications Warehouse

Carlin, James F.

2005-01-01

Tin was one of the first metals discovered by humans and, like most metals, tin is rarely used by itself. Most tin is used as a protective coating or as an alloy with other metals in a diverse range of commercial and defense applications.

Superlative TINs

NASA Technical Reports Server (NTRS)

Chamberlin, R.

2002-01-01

TIN is short for 'triangulated irregular network,' which is a piecewise planar model of a surface. If properly constructed, a TIN can be more than 30 times as efficient as a regular triangulation. In our project (a ground combat simulation to support U.S. Army training exercises), the TIN is used to represent the Earth's surface and is used primarily to determine whether line of sight is blocked by terrain. High efficiency requires accurate identification of ridgelines with as few triangles as possible. The work currently in progress is the implementation of a TINning process that we hope will produce superlative TINs. This presentation describes that process.

Tin whiskers in electronic circuits

NASA Astrophysics Data System (ADS)

Stupian, Gary W.

1992-12-01

Fibrous, conducting 'whiskers' often grow on pure tin plating. These tin whiskers have, for many years, been known to pose a reliability problem in electronic circuitry; therefore, the use of pure tin coatings in any critical electronic application is not recommended. Despite the warnings of the experts, tin plating is still found on electronic and mechanical components and problems with whiskers still arise. This document summarizes what is known about the growth of tin whiskers. A number of factors (e.g., coating thickness, plating conditions) are thought to be important in determining whether whiskers will grow. Although tin whiskers have been investigated from some decades, there is still disagreement on the effects of virtually every coating parameter. There is no disagreement, however, on the essential fact that it is very difficult to predict with certainty whether whiskers will grow on any specific tin-plated component, which of course is the basis of the 'experts' advice not to use pure tin plating. If tin-plated components are found in an electronic system, replacement is the safest policy. Some additional recommendations to minimize risk are presented here that may be of use in situations in which replacement of all suspect components is not the option of choice because of cost or schedule constraints.

Pattern Adaptation and Normalization Reweighting.

PubMed

Westrick, Zachary M; Heeger, David J; Landy, Michael S

2016-09-21

Adaptation to an oriented stimulus changes both the gain and preferred orientation of neural responses in V1. Neurons tuned near the adapted orientation are suppressed, and their preferred orientations shift away from the adapter. We propose a model in which weights of divisive normalization are dynamically adjusted to homeostatically maintain response products between pairs of neurons. We demonstrate that this adjustment can be performed by a very simple learning rule. Simulations of this model closely match existing data from visual adaptation experiments. We consider several alternative models, including variants based on homeostatic maintenance of response correlations or covariance, as well as feedforward gain-control models with multiple layers, and we demonstrate that homeostatic maintenance of response products provides the best account of the physiological data. Adaptation is a phenomenon throughout the nervous system in which neural tuning properties change in response to changes in environmental statistics. We developed a model of adaptation that combines normalization (in which a neuron's gain is reduced by the summed responses of its neighbors) and Hebbian learning (in which synaptic strength, in this case divisive normalization, is increased by correlated firing). The model is shown to account for several properties of adaptation in primary visual cortex in response to changes in the statistics of contour orientation. Copyright © 2016 the authors 0270-6474/16/369805-12$15.00/0.

Chinese Tertiary Teachers' Goal Orientations for Teaching and Teaching Approaches: The Mediation of Teacher Engagement

ERIC Educational Resources Information Center

Yin, Hongbiao; Han, Jiying; Lu, Genshu

2017-01-01

This study investigated the effects of Chinese tertiary teachers' goal orientations for teaching on their approaches to teaching mediated by teacher engagement. In a survey of 597 Chinese tertiary teachers, the respondents placed particular emphasis on relational and mastery goals and expressed a preference for student-focused approaches to…

Learning Processes of Students in Pre-Vocational Secondary Education: Relations between Goal Orientations, Information Processing Strategies and Development of Conceptual Knowledge

ERIC Educational Resources Information Center

Koopman, Maaike; Den Brok, Perry; Beijaard, Douwe; Teune, Peter

2011-01-01

The purpose of this study was to investigate relations between goal orientations, information processing strategies and development of conceptual knowledge of pre-vocational secondary education students (n = 719; 14 schools). Students' preferences for certain types of goals and information processing strategies were examined using questionnaires.…

The Work Orientations of Australian University Students

ERIC Educational Resources Information Center

Taylor, Jeannette; Pick, David

2008-01-01

It is the aim of this paper to provide a better understanding of how university students in Australia are preparing for their future work in the labour market through their work orientations. It draws upon a survey of over 300 final-year undergraduates to present their rationales for engaging in paid work, and their preferences for different job…

Assessing Motivation of Secondary School Students: An Analysis of Promotion and Prevention Orientations as Measured by the Regulatory Focus Questionnaire

ERIC Educational Resources Information Center

Hodis, Flaviu A.; Hodis, Georgeta M.

2017-01-01

Measuring human motivation requires understanding the outcomes individuals value and the strategies they prefer to employ to attain them. Knowledge of promotion and prevention, two pivotal motivation orientations, provide key information regarding these aspects. The Regulatory Focus Questionnaire, which measures these two independent constructs,…

Friction and wear of tin and tin alloys from minus 100 C to 150 C

NASA Technical Reports Server (NTRS)

Buckley, D. H.

1975-01-01

Sliding friction experiments were conducted with an iron (110) single-crystal pin sliding on single and polycrystalline tin and tin alloys. Specimens were examined at various ambient temperatures from -100 to 150 C. Applied loads varied from 1 to 50 grams, and sliding velocity was constant at 0.7 mm/min. Results indicate that the crystal transformation of tin influences the friction coefficient. Friction was higher for the diamond structure (gray tin) than it was for the body-centered tetragonal structure (white tin). Bismuth arrested the crystal transformation, which resulted in constant friction over the temperature range -100 to 150 C. Both copper and aluminum enhanced the kinetics of transformation, with aluminum producing a nearly twofold change in friction with the crystal transformation.

Computational study of antimalarial pyrazole alkaloids from Newbouldia laevis.

PubMed

Mammino, Liliana; Bilonda, Mireille K

2014-11-01

Six pyrazole alkaloids of natural origin (isolated from Newbouldia laevis in DR Congo) that exhibit antimalarial activity-namely withasomnine, newbouldine, and their para-hydroxy and -methoxy derivatives-were investigated theoretically. The nitro derivatives of withasomnine and para-hydroxywithasomnine, which show enhanced antimalarial activity, were also studied in this manner. A thorough conformational study was performed in vacuo and in three solvents (chloroform, acetonitrile, and water) at different levels of theory (HF, DFT/B3LYP, and MP2) using different basis sets. Adducts with explicit water molecules were calculated at the HF level. Due to the rigidity of the pyrazole system and the benzene ring, the only factor that influences the energies of withasomnine and newbouldine is the relative orientation of the two ring systems; two orientations are equally preferred. The para-hydroxy and -methoxy derivatives show a preference for a planar orientation of the OH and OC bonds. The main stabilizing influence on the nitro derivative of para-hydroxywithasomnine is the intramolecular hydrogen bond between the two consecutive functional groups. The calculated adducts show the preferred arrangements of water molecules in the vicinity of the N atoms of the pyrazole system and, for the derivatives, also in the vicinity of the substituents on the benzene ring.

Structural study of Mg doped cobalt ferrite thin films on ITO coated glass substrate

NASA Astrophysics Data System (ADS)

Suthar, Mahesh; Bapna, Komal; Kumar, Kishor; Ahuja, B. L.

2018-05-01

We have synthesized thin films of Co1-xMgxFe2O4 (x = 0, 0.4, 0.6, 0.8, 1) on transparent conducting indium tin oxide (ITO) coated glass substrate by pulsed laser deposition method. The structural properties of the grown films were analyzed by the X-ray diffraction and Raman spectroscopy, which suggest the single phase growth of these films. Raman spectra revealed the incorporation of Mg ions into CoFe2O4 lattice and suggest that the Mg ions initially go both to the octahedral and tetrahedral sites upto a certain concentration. For higher concentration, Mg ions prefer to occupy the tetrahedral sites.

A review of tin oxide-based catalytic systems: Preparation, characterization and catalytic behavior

NASA Technical Reports Server (NTRS)

Hoflund, Gar B.

1987-01-01

This paper reviews the important aspects of the preparation, characterization and catalytic behavior of tin oxide-based catalytic systems including doped tin oxide, mixed oxides which contain tin oxide, Pt supported on tin oxide and Pt/Sn supported on alumina. These systems have a broad range of applications and are continually increasing in importance. However, due to their complex nature, much remains to be understood concerning how they function catalytically.

Contributions of Stress and Oxidation on the Formation of Whiskers in Pb-free Solders

DTIC Science & Technology

2016-01-29

environmental factors influencing formation of tin whiskers on electrodeposited lead free, tin coatings over copper (or copper containing) substrates is the...Oxidation on the Formation of Whiskers in Pb‐free Solders,” WP-1754 15. SUBJECT TERMS Tin Whiskers, Residual Stress, Environmental Degradation 16...showing the surface of a tin film with whisker .................... 2 Figure 2: SEM Micrograph of Tin film on Copper Substrate cross-sectioned by FIB

Ultra-high-pressure homogenization (UHPH) system for producing high-quality vegetable-based beverages: physicochemical, microbiological, nutritional and toxicological characteristics.

PubMed

Ferragut, Victoria; Hernández-Herrero, Manuela; Veciana-Nogués, María Teresa; Borras-Suarez, Miquel; González-Linares, Javier; Vidal-Carou, María Carmen; Guamis, Buenaventura

2015-03-30

A relatively new technology based on a continuous system of ultra-high-pressure homogenization (UHPH) was used for producing high-quality soy and almond beverages as an alternative to conventional heat treatments (pasteurization and UHT). The aim of this study was to compare those treatments by analyzing the most relevant quality parameters with a broad vision from the production to the potential toxicological changes, passing through the main nutritional characteristics. UHPH treatment at 200 MPa, 55 °C T(in) produced a higher reduction of microorganisms than pasteurization. UHPH treatment at 300 MPa, 75 °C T(in) led to complete inactivation of microorganisms, similar to UHT treatment. A much better colloidal stability was observed in both UHPH-treated almond and soy beverages compared with those processed by conventional heat treatments. UHPH treatments led to the same increase in digestibility as heat treatments and did not produce a reduction in the availability of lysine. In addition, UHPH samples of soy beverage seem to be less allergenic based on their lower gut immune response in comparison with heat-treated samples. UHPH treatments could be used to produce high-quality commercial vegetable beverages with different quality standards (fresh or long-life storage) according to consumer preference. © 2014 Society of Chemical Industry.

48 CFR 204.7202-3 - TINs.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false TINs. 204.7202-3 Section... OF DEFENSE GENERAL ADMINISTRATIVE MATTERS Contractor Identification 204.7202-3 TINs. Requirements for use of TINs are in FAR subpart 4.9. [64 FR 43100, Aug. 9, 1999] ...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

48 CFR 204.7202-3 - TINs.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false TINs. 204.7202-3 Section... OF DEFENSE GENERAL ADMINISTRATIVE MATTERS Contractor Identification 204.7202-3 TINs. Requirements for use of TINs are in FAR subpart 4.9. [64 FR 43100, Aug. 9, 1999] ...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

48 CFR 204.7202-3 - TINs.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false TINs. 204.7202-3 Section... OF DEFENSE GENERAL ADMINISTRATIVE MATTERS Contractor Identification 204.7202-3 TINs. Requirements for use of TINs are in FAR subpart 4.9. [64 FR 43100, Aug. 9, 1999] ...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

48 CFR 204.7202-3 - TINs.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false TINs. 204.7202-3 Section... OF DEFENSE GENERAL ADMINISTRATIVE MATTERS Contractor Identification 204.7202-3 TINs. Requirements for use of TINs are in FAR subpart 4.9. [64 FR 43100, Aug. 9, 1999] ...

77 FR 3725 - Proposed Significant New Use Rules on Certain Chemical Substances; Extension of Comment Period

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-25

... chemical substances rutile, tin zinc, calcium-doped (CAS No. 389623-01- 2) and rutile, tin zinc, sodium... substances rutile, tin zinc, calcium- doped (CAS No. 389623-01-2) and rutile, tin zinc, sodium-doped (CAS No...

48 CFR 204.7202-3 - TINs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false TINs. 204.7202-3 Section... OF DEFENSE GENERAL ADMINISTRATIVE MATTERS Contractor Identification 204.7202-3 TINs. Requirements for use of TINs are in FAR subpart 4.9. [64 FR 43100, Aug. 9, 1999] ...

Metallic tin quantum sheets confined in graphene toward high-efficiency carbon dioxide electroreduction

NASA Astrophysics Data System (ADS)

Lei, Fengcai; Liu, Wei; Sun, Yongfu; Xu, Jiaqi; Liu, Katong; Liang, Liang; Yao, Tao; Pan, Bicai; Wei, Shiqiang; Xie, Yi

2016-09-01

Ultrathin metal layers can be highly active carbon dioxide electroreduction catalysts, but may also be prone to oxidation. Here we construct a model of graphene confined ultrathin layers of highly reactive metals, taking the synthetic highly reactive tin quantum sheets confined in graphene as an example. The higher electrochemical active area ensures 9 times larger carbon dioxide adsorption capacity relative to bulk tin, while the highly-conductive graphene favours rate-determining electron transfer from carbon dioxide to its radical anion. The lowered tin-tin coordination numbers, revealed by X-ray absorption fine structure spectroscopy, enable tin quantum sheets confined in graphene to efficiently stabilize the carbon dioxide radical anion, verified by 0.13 volts lowered potential of hydroxyl ion adsorption compared with bulk tin. Hence, the tin quantum sheets confined in graphene show enhanced electrocatalytic activity and stability. This work may provide a promising lead for designing efficient and robust catalysts for electrolytic fuel synthesis.

Platelet composite coatings for tin whisker mitigation

DOE PAGES

Rohwer, Lauren E. S.; Martin, James E.

2015-09-14

In this study, reliable methods for tin whisker mitigation are needed for applications that utilize tin-plated commercial components. Tin can grow whiskers that can lead to electrical shorting, possibly causing critical systems to fail catastrophically. The mechanisms of tin whisker growth are unclear and this makes prediction of the lifetimes of critical components uncertain. The development of robust methods for tin whisker mitigation is currently the best approach to eliminating the risk of shorting. Current mitigation methods are based on unfilled polymer coatings that are not impenetrable to tin whiskers. In this paper we report tin whisker mitigation results formore » several filled polymer coatings. The whisker-penetration resistance of the coatings was evaluated at elevated temperature and high humidity and under temperature cycling conditions. The composite coatings comprised Ni and MgF 2-coated Al/Ni/Al platelets in epoxy resin or silicone rubber. In addition to improved whisker mitigation, these platelet composites have enhanced thermal conductivity and dielectric constant compared with unfilled polymers.« less

Platelet Composite Coatings for Tin Whisker Mitigation

NASA Astrophysics Data System (ADS)

Rohwer, Lauren E. S.; Martin, James E.

2015-11-01

Reliable methods for tin whisker mitigation are needed for applications that utilize tin-plated commercial components. Tin can grow whiskers that can lead to electrical shorting, possibly causing critical systems to fail catastrophically. The mechanisms of tin whisker growth are unclear and this makes prediction of the lifetimes of critical components uncertain. The development of robust methods for tin whisker mitigation is currently the best approach to eliminating the risk of shorting. Current mitigation methods are based on unfilled polymer coatings that are not impenetrable to tin whiskers. In this paper we report tin whisker mitigation results for several filled polymer coatings. The whisker-penetration resistance of the coatings was evaluated at elevated temperature and high humidity and under temperature cycling conditions. The composite coatings comprised Ni and MgF2-coated Al/Ni/Al platelets in epoxy resin or silicone rubber. In addition to improved whisker mitigation, these platelet composites have enhanced thermal conductivity and dielectric constant compared with unfilled polymers.

Polynucleotides encoding TRF1 binding proteins

DOEpatents

Campisi, Judith; Kim, Sahn-Ho

2002-01-01

The present invention provides a novel telomere associated protein (Trf1-interacting nuclear protein 2 "Tin2") that hinders the binding of Trf1 to its specific telomere repeat sequence and mediates the formation of a Tin2-Trf1-telomeric DNA complex that limits telomerase access to the telomere. Also included are the corresponding nucleic acids that encode the Tin2 of the present invention, as well as mutants of Tin2. Methods of making, purifying and using Tin2 of the present invention are described. In addition, drug screening assays to identify drugs that mimic and/or complement the effect of Tin2 are presented.

Optical Properties and Plasmonic Performance of Titanium Nitride

PubMed Central

Patsalas, Panos; Kalfagiannis, Nikolaos; Kassavetis, Spyros

2015-01-01

Titanium nitride (TiN) is one of the most well-established engineering materials nowadays. TiN can overcome most of the drawbacks of palsmonic metals due to its high electron conductivity and mobility, high melting point and due to the compatibility of its growth with Complementary Metal Oxide Semiconductor (CMOS) technology. In this work, we review the dielectric function spectra of TiN and we evaluate the plasmonic performance of TiN by calculating (i) the Surface Plasmon Polariton (SPP) dispersion relations and (ii) the Localized Surface Plasmon Resonance (LSPR) band of TiN nanoparticles, and we demonstrate a significant plasmonic performance of TiN.

Estimating the Probability of Electrical Short Circuits from Tin Whiskers. Part 2

NASA Technical Reports Server (NTRS)

Courey, Karim J.; Asfour, Shihab S.; Onar, Arzu; Bayliss, Jon A.; Ludwig, Larry L.; Wright, Maria C.

2009-01-01

To comply with lead-free legislation, many manufacturers have converted from tin-lead to pure tin finishes of electronic components. However, pure tin finishes have a greater propensity to grow tin whiskers than tin-lead finishes. Since tin whiskers present an electrical short circuit hazard in electronic components, simulations have been developed to quantify the risk of said short circuits occurring. Existing risk simulations make the assumption that when a free tin whisker has bridged two adjacent exposed electrical conductors, the result is an electrical short circuit. This conservative assumption is made because shorting is a random event that had an unknown probability associated with it. Note however that due to contact resistance electrical shorts may not occur at lower voltage levels. In our first article we developed an empirical probability model for tin whisker shorting. In this paper, we develop a more comprehensive empirical model using a refined experiment with a larger sample size, in which we studied the effect of varying voltage on the breakdown of the contact resistance which leads to a short circuit. From the resulting data we estimated the probability distribution of an electrical short, as a function of voltage.

Demonstration of high-performance p-type tin oxide thin-film transistors using argon-plasma surface treatments

NASA Astrophysics Data System (ADS)

Bae, Sang-Dae; Kwon, Soo-Hun; Jeong, Hwan-Seok; Kwon, Hyuck-In

2017-07-01

In this work, we investigated the effects of low-temperature argon (Ar)-plasma surface treatments on the physical and chemical structures of p-type tin oxide thin-films and the electrical performance of p-type tin oxide thin-film transistors (TFTs). From the x-ray photoelectron spectroscopy measurement, we found that SnO was the dominant phase in the deposited tin oxide thin-film, and the Ar-plasma treatment partially transformed the tin oxide phase from SnO to SnO2 by oxidation. The resistivity of the tin oxide thin-film increased with the plasma-treatment time because of the reduced hole concentration. In addition, the root-mean-square roughness of the tin oxide thin-film decreased as the plasma-treatment time increased. The p-type oxide TFT with an Ar-plasma-treated tin oxide thin-film exhibited excellent electrical performance with a high current on-off ratio (5.2 × 106) and a low off-current (1.2 × 10-12 A), which demonstrates that the low-temperature Ar-plasma treatment is a simple and effective method for improving the electrical performance of p-type tin oxide TFTs.

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

Inactivation of the infragranular striate cortex broadens orientation tuning of supragranular visual neurons in the cat.

PubMed

Allison, J D; Bonds, A B

1994-01-01

Intracortical inhibition is believed to enhance the orientation tuning of striate cortical neurons, but the origin of this inhibition is unclear. To examine the possible influence of ascending inhibitory projections from the infragranular layers of striate cortex on the orientation selectivity of neurons in the supragranular layers, we measured the spatiotemporal response properties of 32 supragranular neurons in the cat before, during, and after neural activity in the infragranular layers beneath the recorded cells was inactivated by iontophoretic administration of GABA. During GABA iontophoresis, the orientation tuning bandwidth of 15 (46.9%) supragranular neurons broadened as a result of increases in response amplitude to stimuli oriented about +/- 20 degrees away from the preferred stimulus angle. The mean (+/- SD) baseline orientation tuning bandwidth (half width at half height) of these neurons was 13.08 +/- 2.3 degrees. Their mean tuning bandwidth during inactivation of the infragranular layers increased to 19.59 +/- 2.54 degrees, an increase of 49.7%. The mean percentage increase in orientation tuning bandwidth of the individual neurons was 47.4%. Four neurons exhibited symmetrical changes in their orientation tuning functions, while 11 neurons displayed asymmetrical changes. The change in form of the orientation tuning functions appeared to depend on the relative vertical alignment of the recorded neuron and the infragranular region of inactivation. Neurons located in close vertical register with the inactivated infragranular tissue exhibited symmetric changes in their orientation tuning functions. The neurons exhibiting asymmetric changes in their orientation tuning functions were located just outside the vertical register. Eight of these 11 neurons also demonstrated a mean shift of 6.67 +/- 5.77 degrees in their preferred stimulus orientation. The magnitude of change in the orientation tuning functions increased as the delivery of GABA was prolonged. Responses returned to normal approximately 30 min after the delivery of GABA was discontinued. We conclude that inhibitory projections from neurons within the infragranular layers of striate cortex in cats can enhance the orientation selectivity of supragranular striate cortical neurons.

Out of control: attentional selection for orientation is thwarted by properties of the underlying neural mechanisms.

PubMed

Du, Feng; Abrams, Richard A

2012-09-01

To avoid sensory overload, people are able to selectively attend to a particular color or direction of motion while ignoring irrelevant stimuli that differ from the desired one. We show here for the first time that it is also possible to selectively attend to a specific line orientation-but with an important caveat: orientations that are perpendicular to the target orientation cannot be suppressed. This effect reflects properties of the neural mechanisms selective for orientation and reveals the extent to which contingent capture is constrained not only by one's top-down goals but also by feature preferences of visual neurons. Copyright © 2012 Elsevier B.V. All rights reserved.

Spatial Instability of the Linearly Polarized Plane Wave in a Cubic Crystal

NASA Astrophysics Data System (ADS)

Kuz'mina, M. S.; Khazanov, E. A.

2016-12-01

We study theoretically the development of a small-scale spatial instability of a plane wave in a cubic crystal with [111], [001] and [101] orientations. It is shown that in the [111] oriented crystals the instability develops at lower intensities than in the [001] and [101] oriented crystals. In the latter two crystals, the instability can significantly be suppressed by choosing the optimal radiation polarization. It is found that in the case of a small B integral, the method of temporal contrast enhancement of laser pulses by generating an orthogonal polarization achieves the largest efficiency with the [101] orientation, while the [001] orientation is more preferable for B > 3.

100-Fold Enhancement of Charge Transport in Uniaxially Oriented Mesoporous Anatase TiO 2 Films

DOE PAGES

Li, Ke; Liu, Jie; Sheng, Xia; ...

2017-12-04

Mesoporous semiconductor films are of considerable interest for applications in photoelectrochemical devices, however, despite intensive research till now, their charge transport properties remain significantly lower than their single-crystal counterparts. Herein, we report a novel low-temperature template-free technique for growing high surface area mesoporous anatase TiO2 films with a preferred [001] crystalline-orientation on FTO-coated glass substrate. Compared to mesoporous films that comprised of randomly oriented crystallites, the uniaxial orientation enables a 100-fold increase in the rate of electron transport. The uniaxially oriented mesoporous anatase TiO2 films exhibit should greatly facilitate the development and application of photoelectrochemical and electrochemical devices.

An Investigation of the Electrical Short Circuit Characteristics of Tin Whiskers

NASA Technical Reports Server (NTRS)

Courey, Karim J.

2008-01-01

In this experiment, an empirical model to quantify the probability of occurrence of an electrical short circuit from tin whiskers as a function of voltage was developed. This model can be used to improve existing risk simulation models FIB and TEM images of a tin whisker confirm the rare polycrystalline structure on one of the three whiskers studied. FIB cross-section of the card guides verified that the tin finish was bright tin.

Effect of Tin, Copper and Boron on the Hot Ductility of 20CrMnTi Steel between 650 °C and 1100 °C

NASA Astrophysics Data System (ADS)

Peng, Hong-bing; Chen, Wei-qing; Chen, Lie; Guo, Dong

2015-02-01

The hot ductility of 20CrMnTi steel with x% tin, y% copper and z ppm boron (x = 0, 0.02; y = 0, 0.2; z = 0, 60) was investigated. The results show that tin and copper in 20CrMnTi steel are detrimental to its hot ductility while adding boron can eliminate the adverse effect and enhance hot ductility greatly. Tin is found to segregate to the boundaries tested by EPMA in 20CrMnTi steel containing tin and copper and tin-segregation is suppressed by adding boron, moreover, copper was found not to segregate to boundaries, however, fine copper sulfide was found from carbon extraction replicas using TEM. The adverse effect of tin and copper on the hot ductility was due mainly to tin segregation and fine copper sulfide in the steel. The proeutectoid ferrite film precipitating along the austenite grain boundary causes the ductility trough of the three examined steels. Tin and copper in 20CrMnTi steel can retard the occurrence of dynamic recrystallization (DRX) while boron-addition can compensate for that change. The beneficial effect of boron on 20CrMnTi steel containing tin and copper might be ascribed to the fact that boron segregates to grain boundaries, accelerates onset of DRX, retards austenite/ferrite transformation and promotes intragranular nucleation of ferrite.

Precipitation Behaviors of TiN Inclusion in GCr15 Bearing Steel Billet

NASA Astrophysics Data System (ADS)

Tian, Qianren; Wang, Guocheng; Zhao, Yang; Li, Jing; Wang, Qi

2018-06-01

There are many types of non-metallic TiN-based inclusions observed in GCr15 bearing steel, including single-particle TiN, multi-particle polymerized TiN, and complex inclusions like TiN-MnS, TiN-MgO-MgAl2O4 (TiN-MgO-MA), and TiN-MgAl2O4-MnS (TiN-MA-MnS). Thermodynamic calculations suggest that single-particle TiN precipitates dominate the mushy zone of GCr15 bearing steel. Kinetic calculations regarding TiN growth suggest that the final size of the single-particle TiN ranges between 1 and 6 μm in the initial concentration range of [pct Ti] = 0.0060 to 0.0079 and [pct N] = 0.0049 to 0.0070, at 1620 to 1640 K and a local cooling rate of 0.5 to 10 K/s. The multi-particle polymerized TiN are formed by single TiN particles in three stages: single-particle TiN inclusions approach each other drawn by the cavity bridge force (CBF), local active angles consolidate, and neck region sintering occurs. Based on the thermodynamic calculations of TiN, MnS, and MgO precipitation, the formation behaviors of complex inclusions of TiN-MnS, TiN-MgO-MA, and TiN-MA-MnS were investigated.

77 FR 32998 - Tin- and Chromium-Coated Steel Sheet From Japan

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-04

... INTERNATIONAL TRADE COMMISSION [Investigation No. 731-TA-860 (Second Review)] Tin- and Chromium... order on tin- and chromium-coated steel sheet from Japan would be likely to lead to continuation or... USITC Publication 4325 (May 2012), entitled Tin- and Chromium-Coated Steel Sheet from Japan...

40 CFR 471.10 - Applicability; description of the lead-tin-bismuth forming subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-tin-bismuth forming subcategory. 471.10 Section 471.10 Protection of Environment ENVIRONMENTAL... METAL POWDERS POINT SOURCE CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.10 Applicability; description of the lead-tin-bismuth forming subcategory. This subpart applies to discharges of pollutants to...

26 CFR 31.3406(j)-1 - Taxpayer Identification Number (TIN) matching program.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 26 Internal Revenue 15 2013-04-01 2013-04-01 false Taxpayer Identification Number (TIN) matching... Number (TIN) matching program. (a) The matching program. Under section 3406(i), the Commissioner has the authority to establish Taxpayer Identification Number (TIN) matching programs. The Commissioner may...

26 CFR 31.3406(j)-1 - Taxpayer Identification Number (TIN) matching program.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 15 2011-04-01 2011-04-01 false Taxpayer Identification Number (TIN) matching... Number (TIN) matching program. (a) The matching program. Under section 3406(i), the Commissioner has the authority to establish Taxpayer Identification Number (TIN) matching programs. The Commissioner may...

26 CFR 31.3406(j)-1 - Taxpayer Identification Number (TIN) matching program.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 15 2012-04-01 2012-04-01 false Taxpayer Identification Number (TIN) matching... Number (TIN) matching program. (a) The matching program. Under section 3406(i), the Commissioner has the authority to establish Taxpayer Identification Number (TIN) matching programs. The Commissioner may...

40 CFR 471.10 - Applicability; description of the lead-tin-bismuth forming subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-tin-bismuth forming subcategory. 471.10 Section 471.10 Protection of Environment ENVIRONMENTAL... METAL POWDERS POINT SOURCE CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.10 Applicability; description of the lead-tin-bismuth forming subcategory. This subpart applies to discharges of pollutants to...

40 CFR 471.10 - Applicability; description of the lead-tin-bismuth forming subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-tin-bismuth forming subcategory. 471.10 Section 471.10 Protection of Environment ENVIRONMENTAL... POINT SOURCE CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.10 Applicability; description of the lead-tin-bismuth forming subcategory. This subpart applies to discharges of pollutants to waters of the...

40 CFR 471.10 - Applicability; description of the lead-tin-bismuth forming subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-tin-bismuth forming subcategory. 471.10 Section 471.10 Protection of Environment ENVIRONMENTAL... METAL POWDERS POINT SOURCE CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.10 Applicability; description of the lead-tin-bismuth forming subcategory. This subpart applies to discharges of pollutants to...

40 CFR 471.10 - Applicability; description of the lead-tin-bismuth forming subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-tin-bismuth forming subcategory. 471.10 Section 471.10 Protection of Environment ENVIRONMENTAL... POINT SOURCE CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.10 Applicability; description of the lead-tin-bismuth forming subcategory. This subpart applies to discharges of pollutants to waters of the...

26 CFR 31.3406(j)-1 - Taxpayer Identification Number (TIN) matching program.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 15 2014-04-01 2014-04-01 false Taxpayer Identification Number (TIN) matching... Number (TIN) matching program. (a) The matching program. Under section 3406(i), the Commissioner has the authority to establish Taxpayer Identification Number (TIN) matching programs. The Commissioner may...

26 CFR 31.3406(j)-1 - Taxpayer Identification Number (TIN) matching program.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 15 2010-04-01 2010-04-01 false Taxpayer Identification Number (TIN) matching... Number (TIN) matching program. (a) The matching program. Under section 3406(i), the Commissioner has the authority to establish Taxpayer Identification Number (TIN) matching programs. The Commissioner may...

Invite, include, and involve: racial groups, ethnic groups, and leisure

Treesearch

Deborah J. Chavez

2000-01-01

All people recreate. Most of us read book and/or magazines, take walks, watch television, tend gardens. Some people enjoy high-risk activities, such as bungee jumping, others prefer to participate in karate at the local boys' club or bingo at the local senior center, while others prefer family-oriented leisure adivities such-as miniature golf. Whatever the leisure...

The Effect of Sequence of Instruction on Students' Cognitive Preferences and Recall in the Context of a Problem-Oriented Method of Teaching.

ERIC Educational Resources Information Center

Boreham, N. C.; And Others

1985-01-01

This study investigated the effects of two sequences of instruction--theory-to-application and application-to-theory--on medical students' cognitive preferences in preclinical science teaching. Results indicate that presenting an example of the clinical application of biochemical theory before presenting the theory itself increased students'…

The Most Preferred and Effective Reviewer of L2 Writing among Automated Grading System, Peer Reviewer and Teacher

ERIC Educational Resources Information Center

Tsai, Min-Hsiu

2017-01-01

Who is the most preferred and deemed the most helpful reviewer in improving student writing? This study exercised a blended teaching method which consists of three currently prevailing reviewers: the automated grading system (AGS, a web-based method), the peer review (a process-oriented approach), and the teacher grading technique (the…

University Council for Educational Administration (UCEA) Academic Department Chairs' Self-Perceived Utilization of Bolman and Deal's Four-Frame Theoretical Model

ERIC Educational Resources Information Center

Clark, Sonya L.; Lindahl, Ronald A.

2014-01-01

This study examined the Bolman and Deal leadership orientation preferred by academic department chairs (ADCs) of Educational Leadership or Administration programs at member colleges and universities of the University Council for Educational Administration (UCEA). A secondary purpose of the study was to examine how the preferred frame of the chairs…

An Adult Face Bias in Infants That is Modulated by Face Race

ERIC Educational Resources Information Center

Heron-Delaney, Michelle; Damon, Fabrice; Quinn, Paul C.; Méary, David; Xiao, Naiqi G.; Lee, Kang; Pascalis, Olivier

2017-01-01

The visual preferences of infants for adult versus infant faces were investigated. Caucasian 3.5- and 6-month-olds were presented with Caucasian adult vs. infant face pairs and Asian adult vs. infant face pairs, in both upright and inverted orientations. Both age groups showed a visual preference for upright adult over infant faces when the faces…

An international comparison study of pharmacy students' achievement goals and their relationship to assessment type and scores.

PubMed

Alrakaf, Saleh; Anderson, Claire; Coulman, Sion A; John, Dai N; Tordoff, June; Sainsbury, Erica; Rose, Grenville; Smith, Lorraine

2015-04-25

To identify pharmacy students' preferred achievement goals in a multi-national undergraduate population, to investigate achievement goal preferences across comparable degree programs, and to identify relationships between achievement goals, academic performance, and assessment type. The Achievement Goal Questionnaire was administered to second year students in 4 universities in Australia, New Zealand, England, and Wales. Academic performance was measured using total scores, multiple-choice questions, and written answers (short essay). Four hundred eighty-six second year students participated. Students showed an overall preference for the mastery-approach goal orientation across all sites. The predicted relationships between goal orientation and multiple-choice questions, and written answers scores, were significant. This study is the first of its kind to examine pharmacy students' achievement goals at a multi-national level and to differentiate between assessment type and measures of achievement motivation. Students adopting a mastery-approach goal are more likely to gain high scores in assessments that measure understanding and depth of knowledge.

An International Comparison Study of Pharmacy Students’ Achievement Goals and their Relationship to Assessment Type and Scores

PubMed Central

Anderson, Claire; Coulman, Sion A.; John, Dai N.; Tordoff, June; Sainsbury, Erica; Rose, Grenville; Smith, Lorraine

2015-01-01

Objective: To identify pharmacy students’ preferred achievement goals in a multi-national undergraduate population, to investigate achievement goal preferences across comparable degree programs, and to identify relationships between achievement goals, academic performance, and assessment type. Methods: The Achievement Goal Questionnaire was administered to second year students in 4 universities in Australia, New Zealand, England, and Wales. Academic performance was measured using total scores, multiple-choice questions, and written answers (short essay). Results: Four hundred eighty-six second year students participated. Students showed an overall preference for the mastery-approach goal orientation across all sites. The predicted relationships between goal orientation and multiple-choice questions, and written answers scores, were significant. Conclusion: This study is the first of its kind to examine pharmacy students’ achievement goals at a multi-national level and to differentiate between assessment type and measures of achievement motivation. Students adopting a mastery-approach goal are more likely to gain high scores in assessments that measure understanding and depth of knowledge. PMID:25995510

Category-specificity in sexual interest in gay men and lesbians.

PubMed

Rullo, Jordan E; Strassberg, Donald S; Israel, Esther

2010-08-01

The present study assessed the category-specificity of sexual interest of gay men and lesbians toward an understanding of the possible interaction of sex and sexual orientation that may exist in this phenomenon. Utilizing viewing time as a measure of sexual interest, we had participants (N = 99) rate the sexual appeal of sexually provocative pictures while the amount of time spent viewing each picture was inconspicuously measured. As hypothesized, same-sex oriented individuals demonstrated a category-specific pattern of sexual interest. That is, gay men and lesbians (1) viewed preferred sex pictures (i.e., of same sex) significantly longer than nonpreferred sex pictures (i.e., of opposite sex) and (2) rated preferred sex pictures as significantly more sexually appealing than nonpreferred sex pictures. Additionally, the difference in viewing times between preferred and nonpreferred sexual stimuli was not significantly different for gay men and lesbians, suggesting that lesbians are as category-specific as gay men. The implications of these findings are discussed.

Therapist qualities preferred by sexual-minority individuals.

PubMed

Burckell, Lisa A; Goldfried, Marvin R

2006-01-01

Psychotherapy research concerning lesbian, gay, and bisexual (LGB) individuals has focused on matching clients on gender and sexual orientation, yet has not considered how factors such as therapeutic skill, presenting problem, and cohort membership may influence preference for therapists. This study was designed to identify those therapist qualities that sexual-minority individuals prefer and to determine how the presenting problem influences therapist choice. Forty-two nonheterosexual adults between 18 and 29 years old ranked 63 therapist characteristics from "Extremely Uncharacteristic" to "Extremely Characteristic" when seeking treatment for a problem in which their sexual orientation was salient and one in which it was not. The analyses of both conditions yielded clusters of items reflecting therapist characteristics that participants considered unfavorable, neutral, beneficial, and essential. Participants valued therapists who had LGB-specific knowledge as well as general therapeutic skills, whereas they indicated that they would avoid therapists who held heterocentric views. Application of these findings to clinical practice and future directions are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved).