Science.gov

Sample records for pressure plasma jet

  1. Atmospheric-pressure plasma jet

    DOEpatents

    Selwyn, Gary S.

    1999-01-01

    Atmospheric-pressure plasma jet. A .gamma.-mode, resonant-cavity plasma discharge that can be operated at atmospheric pressure and near room temperature using 13.56 MHz rf power is described. Unlike plasma torches, the discharge produces a gas-phase effluent no hotter than 250.degree. C. at an applied power of about 300 W, and shows distinct non-thermal characteristics. In the simplest design, two concentric cylindrical electrodes are employed to generate a plasma in the annular region therebetween. A "jet" of long-lived metastable and reactive species that are capable of rapidly cleaning or etching metals and other materials is generated which extends up to 8 in. beyond the open end of the electrodes. Films and coatings may also be removed by these species. Arcing is prevented in the apparatus by using gas mixtures containing He, which limits ionization, by using high flow velocities, and by properly shaping the rf-powered electrode. Because of the atmospheric pressure operation, no ions survive for a sufficiently long distance beyond the active plasma discharge to bombard a workpiece, unlike low-pressure plasma sources and conventional plasma processing methods.

  2. Atmospheric pressure plasma jet applications

    SciTech Connect

    Park, J.; Herrmann, H.W.; Henins, I.; Selwyn, G.S.

    1998-12-31

    The atmospheric pressure plasma jet (APPJ) is a non-thermal, high pressure plasma discharge that produces a high velocity effluent stream of highly reactive chemical species. The discharge operates on a feedstock gas (e.g., He/O2/H2O) which flows between two concentric cylindrical electrodes: an outer grounded electrode and an inner electrode powered at 13.56 MHz RF. While passing through the plasma, the feedgas becomes excited, ionized or dissociated by electron impact. The fast-flowing effluent consists of ions and electrons, which are rapidly lost by recombination, highly reactive radicals (e.g., O, OH), and metastable species (e.g., O2). The metastable O2, which is reactive to hydrocarbon and other organic species, has been observed through optical emission spectroscopy to decrease by a factor of 2 from the APPJ nozzle exit to a distance of 10 cm. Unreacted metastable O2, and that which does not impinge on a surface, will then decay back to ordinary ground state O2, resulting in a completely dry, environmentally-benign form of surface cleaning. Applications such as removal of photoresist, oxide films and organic residues from wafers for the electronics industry, decontamination of civilian and military areas and personnel exposed to chemical or biological warfare agents, and paint (e.g., graffiti) removal are being considered.

  3. Large area atmospheric-pressure plasma jet

    DOEpatents

    Selwyn, Gary S.; Henins, Ivars; Babayan, Steve E.; Hicks, Robert F.

    2001-01-01

    Large area atmospheric-pressure plasma jet. A plasma discharge that can be operated at atmospheric pressure and near room temperature using 13.56 MHz rf power is described. Unlike plasma torches, the discharge produces a gas-phase effluent no hotter than 250.degree. C. at an applied power of about 300 W, and shows distinct non-thermal characteristics. In the simplest design, two planar, parallel electrodes are employed to generate a plasma in the volume therebetween. A "jet" of long-lived metastable and reactive species that are capable of rapidly cleaning or etching metals and other materials is generated which extends up to 8 in. beyond the open end of the electrodes. Films and coatings may also be removed by these species. Arcing is prevented in the apparatus by using gas mixtures containing He, which limits ionization, by using high flow velocities, and by properly spacing the rf-powered electrode. Because of the atmospheric pressure operation, there is a negligible density of ions surviving for a sufficiently long distance beyond the active plasma discharge to bombard a workpiece, unlike the situation for low-pressure plasma sources and conventional plasma processing methods.

  4. Electrode Configurations in Atmospheric Pressure Plasma Jets

    NASA Astrophysics Data System (ADS)

    Lietz, Amanda M.; Kushner, Mark J.

    2016-09-01

    Atmospheric pressure plasma jets (APPJs) are being studied for emerging medical applications including cancer treatment and wound healing. APPJs typically consist of a dielectric tube through which a rare gas flows, sometimes with an O2 or H2O impurity. In this paper, we present results from a computational study of APPJs using nonPDPSIM, a 2-D plasma hydrodynamics model, with the goal of providing insights on how the placement of electrodes can influence the production of reactive species. Gas consisting of He/O2 = 99.5/0.5 is flowed through a capillary tube at 2 slpm into humid air, and a pulsed DC voltage is applied. An APPJ with two external ring electrodes will be compared with one having a powered electrode inside and a ground electrode on the outside. The consequences on ionization wave propagation and the production of reactive oxygen and nitrogen species (RONS) will be discussed. Changing the electrode configuration can concentrate the power deposition in volumes having different gas composition, resulting in different RONS production. An internal electrode can result in increased production of NOx and HNOx by increasing propagation of the ionization wave through the He dominated plume to outside of the tube where humid air is diffusing into the plume. Work supported by US DOE Office of Fusion Energy Science and the National Science Foundation.

  5. Bacterial Inactivation by Atmospheric Pressure Dielectric Barrier Discharge Plasma Jet

    NASA Astrophysics Data System (ADS)

    Deng, Sanxi; Cheng, Cheng; Ni, Guohua; Meng, Yuedong; Chen, Hua

    2008-08-01

    Bacillus subtilis and Escherichia coli seeded in two media (agar and filter papers) were exposed to after-glow plasma emitted from a atmospheric pressure dielectric barrier discharge (DBD) plasma jet generator in open air with a temperature of about 30-80 °C. In order to estimate the inactivation of microorganism using DBD plasma jet, various plasma conditions (such as treatment time and feed-gas composition of plasma jet) were changed. The results shown that the effective area of inactivation increased with the plasma treatment time as the bacteria seeded in Agar medium. The effective area of inactivation was much bigger than plasma jet treatment area after 5 min treatment. With the use of filter papers as the supporting media, the addition of reactive gases (oxygen, hydrogen peroxide vapor) into the plasma jet system, compared with only pure noble gas, led to a significant improvement in the bacterial Inactivation efficacy.

  6. Electrical characteristics and formation mechanism of atmospheric pressure plasma jet

    SciTech Connect

    Liu, Lijuan; Zhang, Yu; Tian, Weijing; Meng, Ying; Ouyang, Jiting

    2014-06-16

    The behavior of atmospheric pressure plasma jet produced by a coplanar dielectric barrier discharge in helium in external electrostatic and magnetic field is investigated. Net negative charges in the plasma jet outside the tube were detected. The deflection of the plume in the external field was observed. The plasma jet is suggested to be formed by the electron beam from the temporal cathode which is accelerated by a longitudinal field induced by the surface charges on the dielectric tube or interface between the helium and ambient air. The helium flow is necessary for the jet formation in the surrounding air.

  7. Cellular membrane collapse by atmospheric-pressure plasma jet

    SciTech Connect

    Kim, Kangil; Sik Yang, Sang E-mail: ssyang@ajou.ac.kr; Jun Ahn, Hak; Lee, Jong-Soo E-mail: ssyang@ajou.ac.kr; Lee, Jae-Hyeok; Kim, Jae-Ho

    2014-01-06

    Cellular membrane dysfunction caused by air plasma in cancer cells has been studied to exploit atmospheric-pressure plasma jets for cancer therapy. Here, we report that plasma jet treatment of cervical cancer HeLa cells increased electrical conductivity across the cellular lipid membrane and caused simultaneous lipid oxidation and cellular membrane collapse. We made this finding by employing a self-manufactured microelectrode chip. Furthermore, increased roughness of the cellular lipid membrane and sequential collapse of the membrane were observed by atomic force microscopy following plasma jet treatment. These results suggest that the cellular membrane catastrophe occurs via coincident altered electrical conductivity, lipid oxidation, and membrane roughening caused by an atmospheric-pressure plasma jet, possibly resulting in cellular vulnerability to reactive species generated from the plasma as well as cytotoxicity to cancer cells.

  8. Cellular membrane collapse by atmospheric-pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Kim, Kangil; Jun Ahn, Hak; Lee, Jae-Hyeok; Kim, Jae-Ho; Sik Yang, Sang; Lee, Jong-Soo

    2014-01-01

    Cellular membrane dysfunction caused by air plasma in cancer cells has been studied to exploit atmospheric-pressure plasma jets for cancer therapy. Here, we report that plasma jet treatment of cervical cancer HeLa cells increased electrical conductivity across the cellular lipid membrane and caused simultaneous lipid oxidation and cellular membrane collapse. We made this finding by employing a self-manufactured microelectrode chip. Furthermore, increased roughness of the cellular lipid membrane and sequential collapse of the membrane were observed by atomic force microscopy following plasma jet treatment. These results suggest that the cellular membrane catastrophe occurs via coincident altered electrical conductivity, lipid oxidation, and membrane roughening caused by an atmospheric-pressure plasma jet, possibly resulting in cellular vulnerability to reactive species generated from the plasma as well as cytotoxicity to cancer cells.

  9. [Spectral diagnosis of plasma jet at atmospheric pressure].

    PubMed

    Li, Chi; Tang, Xiao-liang; Qiu, Gao

    2008-12-01

    A new approach to surface modification of materials using dielectric barrier discharge (DBD) plasma jet at atmospheric pressure is presented in the present paper. The emission spectral lines of argon plasma jet at atmospheric pressure were recorded by the grating spectrograph HR2000 and computer software. The argon plasma emission spectra, ranging from 300nm to 1000 nm, were measured at different applied voltage. Compared to air plasma emission spectra under the same circumstance, it is shown that all of the spectral lines are attributed to neutral argon atoms. The spectral lines 763.51 and 772.42 nm were chosen to estimate the electron excitation temperature. The purpose of the study is to research the relationship between the applied voltage and temperature to control the process of materials' surface modification promptly. The results show that electron excitation temperature is in the range of 0.1-0.5 eV and increases with increasing applied voltage. In the process of surface modification under the plasma jet, the infrared radiation thermometer was used to measure the material surface temperature under the plasma jet. The results show that the material surface temperature is in the range of 50-100 degrees C and it also increases with increasing applied voltage. Because the material surface was under the plasma jet and its temperature was decided by the plasma, and the material surface temperature increased with increasing the macro-temperature of plasma jet, the relationship between the surface temperature and applied voltage indicates the relationship between the macro-temperature of the plasma jet and the applied voltage approximately. The experimental results indicate that DBD plasma jet at atmospheric pressure is a new approach to improving the quality of materials' surface modification, and spectral diagnosis has proved to be a kind of workable method by choosing suitable applied voltage.

  10. Inactivation of Escherichia coli using atmospheric-pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Kuwahata, Hiroshi; Yamaguchi, Takeshi; Ohyama, Ryu-ichiro; Ito, Atsushi

    2015-01-01

    An atmospheric-pressure argon (Ar) plasma jet was applied to the inactivation of Escherichia coli. The Ar plasma jet was generated at a frequency of 10 kHz, an applied voltage of 10 kV, and an Ar gas flow rate of 10 L/min at atmospheric pressure. E. coli cells seeded on an agar medium in a Petri dish were inactivated by Ar plasma jet irradiation for 1 s. Scanning electron microscopy (SEM) revealed that E. coli cells were killed because their cell wall and membrane were disrupted. To determine the causes of the disruption of the cell wall and membrane of E. coli, we performed the following experiments: the measurement of the surface temperature of an agar medium using a thermograph, the analysis of an emission spectrum of a plasma jet obtained using a multichannel spectrometer, and the determination of the distribution of the concentration of hydrogen peroxide (H2O2) generated on an agar medium by plasma jet irradiation using semiquantitative test strips. Moreover, H2O2 solutions of different concentrations were dropped onto an agar medium seeded with E. coli cells to examine the contribution of H2O2 to the death of E. coli. The results of these experiments showed that the cell wall and membrane of E. coli were disrupted by electrons in the plasma jet, as well as by electroneutral excited nitrogen molecules (N2) and hydroxyl (OH) radicals in the periphery of the plasma jet.

  11. Generation of reactive species by an atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Kelly, S.; Turner, M. M.

    2014-12-01

    The role of gas mixing in reactive species delivery to treatment surfaces for an atmospheric pressure capacitively coupled plasma helium jet is investigated by numerical modelling. Atomic oxygen in the jet effluent is shown to quickly convert to ozone for increasing device to surface separation due to the molecular oxygen present in the gas mixture. Surface profiles of reactive oxygen species show narrow peaks for atomic oxygen and broader surface distributions for ozone and metastable species. Production efficiency of atomic oxygen to the helium plasma jet by molecular oxygen admixture is shown to be dependent on electro-negativity. Excessive molecular oxygen admixture results in negative ion dominance over electrons which eventually quenches the plasma. Interaction of the plasma jet with an aqueous surface showed hydrogen peroxide as the dominant species at this interface. Gas heating by the plasma is found to be dominated by elastic electron collisions and positive ion heating. Comparison with experimental measurements for atomic oxygen shows good agreement.

  12. Dynamics of apokamp-type atmospheric pressure plasma jets

    NASA Astrophysics Data System (ADS)

    Sosnin, Eduard A.; Panarin, Victor A.; Skakun, Victor S.; Baksht, Evgeny Kh.; Tarasenko, Victor F.

    2017-02-01

    The paper describes a new discharge source of atmospheric pressure plasma jets (APPJs) in air with no gas supply through the discharge region. In this discharge mode, plasma jets develop from the bending point of a bright current channel between two electrodes and are therefore termed an apokamp (from Greek `off' and `bend'). The apokamp can represent single plasma jets of length up 6 cm or several jets, and the temperature of such jets can range from more than 1000 °C at their base to 100-250 °C at their tip. Apokamps are formed at maximum applied voltage of positive polarity, provided that the second electrode is capacitively decoupled with ground. According to high-speed photography with time resolution from several nanoseconds to several tens of nanoseconds, the apokamp consists of a set of plasma bullets moving with a velocity of 100-220 km/s, which excludes the convective mechanism of plasma decay. Estimates on a 100-ns scale show that the near-electrode zones and the zones from which apokamps develop are close in temperature.

  13. The evolution of atmospheric-pressure low-temperature plasma jets: jet current measurements

    NASA Astrophysics Data System (ADS)

    Karakas, Erdinc; Arda Akman, Mehmet; Laroussi, Mounir

    2012-06-01

    In this study, we report insights into the dynamics of atmospheric-pressure low-temperature plasma jets (APLTPJs). The plasma jet current was measured by a Pearson current monitor for different operating conditions. These jet current measurements confirmed a proposed photo-ionization model based on streamer theory. Our results are supported by intensified charged-couple device camera observations. It was found that a secondary discharge ignition, arising from the positive high-voltage electrode, causes the inhibition of plasma bullet propagation. Our observations also showed the existence of an ionization channel between the APLTPJ reactor and the plasma bullet. In addition, the maximum electron density along the plasma jet was estimated using Ohm's law, and an empirical relationship was derived between the plasma bullet velocity and the plasma bullet area.

  14. Polymerization of acrylic acid using atmospheric pressure DBD plasma jet

    NASA Astrophysics Data System (ADS)

    Bashir, M.; Bashir, S.

    2016-08-01

    In this paper polymerization of acrylic acid was performed using non thermal atmospheric pressure plasma jet technology. The goal of this study is to deposit organic functional coatings for biomedical applications using a low cost and rapid growth rate plasma jet technique. The monomer solution of acrylic acid was vaporized and then fed into the argon plasma for coating. The discharge was powered using a laboratory made power supply operating with sinusoidal voltage signals at a frequency of 10 kHz. The optical emission spectra were collected in order to get insight into the plasma chemistry during deposition process. The coatings were characterized using Fourier transform infrared spectroscopy, atomic force microscopy and growth rates analysis. A high retention of carboxylic functional groups of the monomer was observed at the surface deposited using this low power technique.

  15. Cold atmospheric pressure plasma jet interactions with plasmid DNA

    SciTech Connect

    O'Connell, D.; Cox, L. J.; Hyland, W. B.; McMahon, S. J.; Reuter, S.; Graham, W. G.; Gans, T.; Currell, F. J.

    2011-01-24

    The effect of a cold (<40 deg. C) radio frequency-driven atmospheric pressure plasma jet on plasmid DNA has been investigated. Gel electrophoresis was used to analyze the DNA forms post-treatment. The experimental data are fitted to a rate equation model that allows for quantitative determination of the rates of single and double strand break formation. The formation of double strand breaks correlates well with the atomic oxygen density. Taken with other measurements, this indicates that neutral components in the jet are effective in inducing double strand breaks.

  16. Atmospheric pressure plasma jet treatment of Salmonella Enteritidis inoculated eggshells.

    PubMed

    Moritz, Maike; Wiacek, Claudia; Koethe, Martin; Braun, Peggy G

    2017-03-20

    Contamination of eggshells with Salmonella Enteritidis remains a food safety concern. In many cases human salmonellosis within the EU can be traced back to raw or undercooked eggs and egg products. Atmospheric pressure plasma is a novel decontamination method that can reduce a wide range of pathogens. The aim of this work was to evaluate the possibility of using an effective short time cold plasma treatment to inactivate Salmonella Enteritidis on the eggshell. Therefore, artificially contaminated eggshells were treated with an atmospheric pressure plasma jet under different experimental settings with various exposure times (15-300s), distances from the plasma jet nozzle to the eggshell surface (5, 8 or 12mm), feed gas compositions (Ar, Ar with 0.2, 0.5 or 1.0% O2), gas flow rates (5 and 7slm) and different inoculations of Salmonella Enteritidis (10(1)-10(6)CFU/cm(2)). Atmospheric pressure plasma could reduce Salmonella Enteritidis on eggshells significantly. Reduction factors ranged between 0.22 and 2.27 log CFU (colony-forming units). Exposure time and, particularly at 10(4)CFU/cm(2) inoculation, feed gas had a major impact on Salmonella reduction. Precisely, longer exposure times led to higher reductions and Ar as feed gas was more effective than ArO2 mixtures.

  17. Atmospheric Pressure Plasma Jet as an Accelerator of Tooth Bleaching

    PubMed Central

    Santak, Vedran; Zaplotnik, Rok; Milosevic, Slobodan; Klaric, Eva; Tarle, Zrinka

    2014-01-01

    Objective To study the effect of atmospheric pressure plasma (APP) jet as a potential accelerator of the degradation of hydrogen peroxide in bleaching gels which could lead to better and faster bleaching. Material and Methods 25 pastilles of hydroxylapatite were colored in green tea for 8 hours and were randomly divided into five groups (n = 5). The bleaching process was performed with 30% and 40% hydrogen peroxide (HP) gel alone and in conjunction with helium APP jet. During the bleaching treatment, optical emission spectroscopy and non-contact surface temperature measurement using pyrometer were performed. Color of the pastilles was determined by a red–green–blue (RGB) colorimeter. PH values of bleaching gels were measured before and after the plasma treatment on additional 10 pastilles using a pH meter with contact pH electrode. Results The color measurements of pastilles before and after the treatment showed that treatment with APP jet improved the bleaching effect by 32% and 15% in the case of 30% and 40% HP gel. Better results were obtained approximately six times faster than with a procedure suggested by the bleaching gel manufacturer. Optical emission spectroscopy proved that plasma has a chemically active role on the gel. After the APP treatment, pH values of bleaching gels dropped to about 50–75% of their initial value while the surface temperature increased by 8–10˚C above baseline. Conclusion The use of plasma jet provides more effective bleaching results in a shorter period of time without a significant temperature increase which may cause damage of the surrounding tissue. PMID:27688375

  18. Electric probe investigations of microwave generated, atmospheric pressure, plasma jets

    SciTech Connect

    Porteanu, H. E.; Kuehn, S.; Gesche, R.

    2010-07-15

    We examine the applicability of the Langmuir-type of characterization for atmospheric pressure plasma jets generated in a millimeter-size cavity microwave resonator at 2.45 GHz. Wide range I-V characteristics of helium, argon, nitrogen, air and oxygen are presented for different gas fluxes, distances probe-resonator, and microwave powers. A detailed analysis is performed for the fine variation in the current around the floating potential. A simplified theory specially developed for this case is presented, considering the ionic and electronic saturation currents and the floating potential. Based on this theory, we conclude that, while the charge carrier density depends on gas flow, distance to plasma source, and microwave absorbed power, the electron temperature is quite independent of these parameters. The resulting plasma parameters for helium, argon, and nitrogen are presented.

  19. Plasmid DNA damage induced by helium atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Han, Xu; Cantrell, William A.; Escobar, Erika E.; Ptasinska, Sylwia

    2014-03-01

    A helium atmospheric pressure plasma jet (APPJ) is applied to induce damage to aqueous plasmid DNA. The resulting fractions of the DNA conformers, which indicate intact molecules or DNA with single- or double-strand breaks, are determined using agarose gel electrophoresis. The DNA strand breaks increase with a decrease in the distance between the APPJ and DNA samples under two working conditions of the plasma source with different parameters of applied electric pulses. The damage level induced in the plasmid DNA is also enhanced with increased plasma irradiation time. The reactive species generated in the APPJ are characterized by optical emission spectra, and their roles in possible DNA damage processes occurring in an aqueous environment are also discussed.

  20. Helium atmospheric pressure plasma jets touching dielectric and metal surfaces

    NASA Astrophysics Data System (ADS)

    Norberg, Seth A.; Johnsen, Eric; Kushner, Mark J.

    2015-07-01

    Atmospheric pressure plasma jets (APPJs) are being investigated in the context plasma medicine and biotechnology applications, and surface functionalization. The composition of the surface being treated ranges from plastics, liquids, and biological tissue, to metals. The dielectric constant of these materials ranges from as low as 1.5 for plastics to near 80 for liquids, and essentially infinite for metals. The electrical properties of the surface are not independent variables as the permittivity of the material being treated has an effect on the dynamics of the incident APPJ. In this paper, results are discussed from a computational investigation of the interaction of an APPJ incident onto materials of varying permittivity, and their impact on the discharge dynamics of the plasma jet. The computer model used in this investigation solves Poisson's equation, transport equations for charged and neutral species, the electron energy equation, and the Navier-Stokes equations for the neutral gas flow. The APPJ is sustained in He/O2 = 99.8/0.2 flowing into humid air, and is directed onto dielectric surfaces in contact with ground with dielectric constants ranging from 2 to 80, and a grounded metal surface. Low values of relative permittivity encourage propagation of the electric field into the treated material and formation and propagation of a surface ionization wave. High values of relative permittivity promote the restrike of the ionization wave and the formation of a conduction channel between the plasma discharge and the treated surface. The distribution of space charge surrounding the APPJ is discussed.

  1. Decolorization of azodyes using the atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Lazovic, Sasa; Maletic, Dejan; Tomic, Natasa; Malovic, Gordana; Cvelbar, Uros; Dohcevic-Mitrovic, Zorana; Petrovic, Zoran Lj.

    2013-09-01

    Atmospheric pressure plasma jet operated in air/argon mixture is tested for decolorization of Bezactiv Orange V-3R dye used in the textile industry. The decolorization efficiency is determined by spectrophotometric measurements at 493.7 nm which corresponds to the breaking of dye N =N bond. The initial concentration of 50 mg/L of dye is reduced 50 times after 120 minutes of treatment by plasma. The results are compared to the efficiency of the suspended TiO2 powder and activated by an UV lamp (300 W). The radicals responsible for removal of the dye are OH and super-anion radical. It is found that efficiency of the plasma and TiO2 + UV is quite similar for the treatment times up to 60 min. After that, TiO2 shows higher decolorization rates (100 times reduction after 90 min). However, when plasma and TiO2 (but without the UV lamp) are applied together, it is found that there are synergetic effects and that the efficiency is increased. Plasma (less than 2 W) is not expected to produce high amounts of UV light in the atmospheric pressure. Supported by MESTD, RS, III41011 and ON 171037.

  2. Nanocapillary Atmospheric Pressure Plasma Jet: A Tool for Ultrafine Maskless Surface Modification at Atmospheric Pressure.

    PubMed

    Motrescu, Iuliana; Nagatsu, Masaaki

    2016-05-18

    With respect to microsized surface functionalization techniques we proposed the use of a maskless, versatile, simple tool, represented by a nano- or microcapillary atmospheric pressure plasma jet for producing microsized controlled etching, chemical vapor deposition, and chemical modification patterns on polymeric surfaces. In this work we show the possibility of size-controlled surface amination, and we discuss it as a function of different processing parameters. Moreover, we prove the successful connection of labeled sugar chains on the functionalized microscale patterns, indicating the possibility to use ultrafine capillary atmospheric pressure plasma jets as versatile tools for biosensing, tissue engineering, and related biomedical applications.

  3. Atmospheric Pressure Plasma Jet for Chem/Bio Warfare Decontamination

    NASA Astrophysics Data System (ADS)

    Herrmann, Hans W.; Henins, Ivars; Park, Jaeyoung; Selwyn, Gary S.

    1999-11-01

    Atmospheric Pressure Plasma Jet (APPJ) technology may provide a much needed method of CBW decontamination which, unlike traditional decon methods, is dry and nondestructive to sensitive equipment and materials. The APPJ discharge uses a high-flow feedgas consisting primarily of an inert carrier gas, such as He, and a small amount of a reactive additive, such as O2, which flows between capacitively-coupled electrodes powered at 13.56 MHz. The plasma generates highly reactive metastable and atomic species of oxygen which are then directed onto a contaminated surface. The reactive effluent of the APPJ has been shown to effectively neutralize VX nerve agent as well as simulants for anthrax and mustard blister agent. Research efforts are now being directed towards reducing He consumption and increasing the allowable stand-off distance. Recent results demonstrate that by replacing the O2 reactive additive with CO2, ozone formation is greatly reduced. This has the result of extending the lifetime of atomic oxygen by an order of magnitude or more. A recirculating APP Decon Chamber which combines heat, vacuum, forced convection and reactivity is currently being developed for enhanced decontamination of sensitive equipment. Several techniques are also being evaluated for use in an APP Decon Jet for decontamination of items which cannot be placed inside a chamber.

  4. Helium atmospheric pressure plasma jets touching dielectric and metal surfaces

    SciTech Connect

    Norberg, Seth A. Johnsen, Eric; Kushner, Mark J.

    2015-07-07

    Atmospheric pressure plasma jets (APPJs) are being investigated in the context plasma medicine and biotechnology applications, and surface functionalization. The composition of the surface being treated ranges from plastics, liquids, and biological tissue, to metals. The dielectric constant of these materials ranges from as low as 1.5 for plastics to near 80 for liquids, and essentially infinite for metals. The electrical properties of the surface are not independent variables as the permittivity of the material being treated has an effect on the dynamics of the incident APPJ. In this paper, results are discussed from a computational investigation of the interaction of an APPJ incident onto materials of varying permittivity, and their impact on the discharge dynamics of the plasma jet. The computer model used in this investigation solves Poisson's equation, transport equations for charged and neutral species, the electron energy equation, and the Navier-Stokes equations for the neutral gas flow. The APPJ is sustained in He/O{sub 2} = 99.8/0.2 flowing into humid air, and is directed onto dielectric surfaces in contact with ground with dielectric constants ranging from 2 to 80, and a grounded metal surface. Low values of relative permittivity encourage propagation of the electric field into the treated material and formation and propagation of a surface ionization wave. High values of relative permittivity promote the restrike of the ionization wave and the formation of a conduction channel between the plasma discharge and the treated surface. The distribution of space charge surrounding the APPJ is discussed.

  5. On non-equilibrium atmospheric pressure plasma jets and plasma bullet

    NASA Astrophysics Data System (ADS)

    Lu, Xinpei

    2012-10-01

    Because of the enhanced plasma chemistry, atmospheric pressure nonequilibrium plasmas (APNPs) have been widely studied for several emerging applications such as biomedical applications. For the biomedical applications, plasma jet devices, which generate plasma in open space (surrounding air) rather than in confined discharge gaps only, have lots of advantages over the traditional dielectric barrier discharge (DBD) devices. For example, it can be used for root canal disinfection, which can't be realized by the traditional plasma device. On the other hand, currently, the working gases of most of the plasma jet devices are noble gases or the mixtures of the noble gases with small amount of O2, or air. If ambient air is used as the working gas, several serious difficulties are encountered in the plasma generation process. Amongst these are high gas temperatures and disrupting instabilities. In this presentation, firstly, a brief review of the different cold plasma jets developed to date is presented. Secondly, several different plasma jet devices developed in our lab are reported. The effects of various parameters on the plasma jets are discussed. Finally, one of the most interesting phenomena of APNP-Js, the plasma bullet is discussed and its behavior is described. References: [1] X. Lu, M. Laroussi, V. Puech, Plasma Sources Sci. Technol. 21, 034005 (2012); [2] Y. Xian, X. Lu, S. Wu, P. Chu, and Y. Pan, Appl. Phys. Lett. 100, 123702 (2012); [3] X. Pei, X. Lu, J. Liu, D. Liu, Y. Yang, K. Ostrikov, P. Chu, and Y. Pan, J. Phys. D 45, 165205 (2012).

  6. Atmospheric Pressure Plasma Jet as a Dry Alternative to Inkjet Printing in Flexible Electronics

    NASA Technical Reports Server (NTRS)

    Gandhiraman, Ram Prasad; Lopez, Arlene; Koehne, Jessica; Meyyappan, M.

    2016-01-01

    We have developed an atmospheric pressure plasma jet printing system that works at room temperature to 50 deg C unlike conventional aerosol assisted techniques which require a high temperature sintering step to obtain desired thin films. Multiple jets can be configured to increase throughput or to deposit multiple materials, and the jet(s) can be moved across large areas using a x-y stage. The plasma jet has been used to deposit carbon nanotubes, graphene, silver nanowires, copper nanoparticles and other materials on substrates such as paper, cotton, plastic and thin metal foils.

  7. Low Temperature Plasma Surface Interactions: Atomic Layer Etching And Atmospheric Pressure Plasma Jet Modification Of Biomaterials

    NASA Astrophysics Data System (ADS)

    Oehrlein, Gottlieb

    2013-09-01

    Control of plasma-surface interactions is essential for successful application of low temperature plasma to materials processing. We review work performed in our laboratory in two areas: First, low pressure plasma surface interaction mechanisms aimed at achieving atomic precision in etching materials in the semiconductor industry. We discuss sequential reactions of surface passivation followed by directional low energy ion attack for ``volatile product'' removal to establish for what conditions self-limiting behavior required for Atomic Layer Etching (ALE) can be established using prototypical SiO2 -Si/fluorocarbon-Ar materials/etching systems. Second, studies of plasma-surface interactions related to application of a non-equilibrium atmospheric pressure plasma jet (APPJ) for modification of biomaterials are discussed. Changes in surface chemistry/biological activity of lipopolysaccharide (LPS) exposed to the APPJ plume/effluent in a controlled environment are reviewed. The results clarify how jet chemistry and interactions of plasma with the environment impact the consequences of APPJ-biomaterial-surface interactions. Based on collaborations with D. Metzler, S. Engelmann, R. Bruce, E. Joseph, E. Bartis, C. Hart, Q.-Y. Yang, J. Seog, T.-Y. Chung, H.-W. Chang, and D.B. Graves. We gratefully acknowledge funding from US Department of Energy (DE-SC0005105; DE-SC0001939) and National Science Foundation (CBET-1134273; PHY-1004256).

  8. Review on VUV to MIR absorption spectroscopy of atmospheric pressure plasma jets

    NASA Astrophysics Data System (ADS)

    Reuter, Stephan; Santos Sousa, Joao; Stancu, Gabi Daniel; Hubertus van Helden, Jean-Pierre

    2015-10-01

    Absorption spectroscopy (AS) represents a reliable method for the characterization of cold atmospheric pressure plasma jets. The method’s simplicity stands out in comparison to competing diagnostic techniques. AS is an in situ, non-invasive technique giving absolute densities, free of calibration procedures, which other diagnostics, such as laser-induced fluorescence or optical emission spectroscopy, have to rely on. Ground state densities can be determined without the knowledge of the influence of collisional quenching. Therefore, absolute densities determined by absorption spectroscopy can be taken as calibration for other methods. In this paper, fundamentals of absorption spectroscopy are presented as an entrance to the topic. In the second part of the manuscript, a review of AS performed on cold atmospheric pressure plasma jets, as they are used e.g. in the field of plasma medicine, is presented. The focus is set on special techniques overcoming not only the drawback of spectrally overlapping absorbing species, but also the line-of-sight densities that AS usually provides or the necessity of sufficiently long absorption lengths. Where references are not available for measurements on cold atmospheric pressure plasma jets, other plasma sources including low-pressure plasmas are taken as an example to give suggestions for possible approaches. The final part is a table summarizing examples of absorption spectroscopic measurements on cold atmospheric pressure plasma jets. With this, the paper provides a ‘best practice’ guideline and gives a compendium of works by groups performing absorption spectroscopy on cold atmospheric pressure plasma jets.

  9. An atmospheric pressure quasiuniform planar plasma jet generated by using a dielectric barrier configuration

    SciTech Connect

    Li Qing; Takana, Hidemasa; Nishiyama, Hideya; Pu Yikang

    2011-06-13

    A stable nonthermal quasiuniform planar plasma jet, originating from a planar dielectric duct with a rectangular exit and issuing into ambient air at atmospheric pressure, is reported in the present work. Current-voltage characteristics, one discharge current pulse per sinusoidal half voltage cycle, show that the discharge is not filamentary. Its spatial uniformity in the transverse direction is shown to be excellent by monitoring optical emission spectra in the jet core region except jet boundaries. This is possibly resulted from high preionization in the upstream region, and it is a challenge to the traditional single streamer explanation for nonthermal plasma jets.

  10. Correlation between helium atmospheric pressure plasma jet (APPJ) variables and plasma induced DNA damage

    NASA Astrophysics Data System (ADS)

    Adhikari, Ek R.; Ptasinska, Sylwia

    2016-09-01

    A helium atmospheric pressure plasma jet (APPJ) source with a dielectric capillary and two tubular electrodes was used to induce damage in aqueous plasmid DNA. The fraction of different types of DNA damage (i.e., intact or undamaged, double strand breaks (DSBs), and single strand breaks (SSBs)) that occurred as the result of plasma irradiation was quantified through analysis of agarose gel electrophoresis images. The total DNA damage increased with an increase in both flow rate and duration of irradiation, but decreased with an increase in distance between the APPJ and sample. The average power of the plasma was calculated and the length of APPJ was measured for various flow rates and voltages applied. The possible effects of plasma power and reactive species on DNA damage are discussed.

  11. Optical Emission Spectroscopy of an Atmospheric Pressure Plasma Jet During Tooth Bleaching Gel Treatment.

    PubMed

    Šantak, Vedran; Zaplotnik, Rok; Tarle, Zrinka; Milošević, Slobodan

    2015-11-01

    Optical emission spectroscopy was performed during atmospheric pressure plasma needle helium jet treatment of various tooth-bleaching gels. When the gel sample was inserted under the plasma plume, the intensity of all the spectral features increased approximately two times near the plasma needle tip and up to two orders of magnitude near the sample surface. The color change of the hydroxylapatite pastille treated with bleaching gels in conjunction with the atmospheric pressure plasma jet was found to be in correlation with the intensity of OH emission band (309 nm). Using argon as an additive to helium flow (2 L/min), a linear increase (up to four times) of OH intensity and, consequently, whitening (up to 10%) of the pastilles was achieved. An atmospheric pressure plasma jet activates bleaching gel, accelerates OH production, and accelerates tooth bleaching (up to six times faster).

  12. Effect of non-thermal atmospheric pressure plasma jet on human breast cancer cells

    NASA Astrophysics Data System (ADS)

    Mirpour, Shahriar; Nikkhah, Maryam; Pirouzmand, Somaye; Ghomi, Hamid Reza

    2012-10-01

    Nowadays, Non-thermal plasma enjoy a wide range of applications in biomedical fields such as Sterilization, Wound healing, Cancer treatment and etc. The aim of this paper is to study the effect of non-thermal atmospheric pressure plasma jet on breast cancer (MCF-7) cells. In this regard the effect of plasma on death of the cancer cells are explored experimentally. The plasma in this discharge is created by pulsed dc high voltage power supply with repetition rate of several tens of kilohertz which led to the inductively coupled plasma. The pure helium gas were used for formation of the plasma jet. MTT assay were used for quantification of death cells. The results showed that the cells death rate increase with plasma exposure time. This study confirm that plasma jet have significant effect on treatment of human breast cancer cells.

  13. Influence of air pressure on the performance of plasma synthetic jet actuator

    NASA Astrophysics Data System (ADS)

    Li, Yang; Jia, Min; Wu, Yun; Li, Ying-hong; Zong, Hao-hua; Song, Hui-min; Liang, Hua

    2016-09-01

    Plasma synthetic jet actuator (PSJA) has a wide application prospect in the high-speed flow control field for its high jet velocity. In this paper, the influence of the air pressure on the performance of a two-electrode PSJA is investigated by the schlieren method in a large range from 7 kPa to 100 kPa. The energy consumed by the PSJA is roughly the same for all the pressure levels. Traces of the precursor shock wave velocity and the jet front velocity vary a lot for different pressures. The precursor shock wave velocity first decreases gradually and then remains at 345 m/s as the air pressure increases. The peak jet front velocity always appears at the first appearance of a jet, and it decreases gradually with the increase of the air pressure. A maximum precursor shock wave velocity of 520 m/s and a maximum jet front velocity of 440 m/s are observed at the pressure of 7 kPa. The averaged jet velocity in one period ranges from 44 m/s to 54 m/s for all air pressures, and it drops with the rising of the air pressure. High velocities of the precursor shock wave and the jet front indicate that this type of PSJA can still be used to influence the high-speed flow field at 7 kPa. Project supported by the National Natural Science Foundation of China (Grant Nos. 51407197, 51522606, 51336011, 91541120, and 11472306).

  14. Production and provision mechanisms of OH radical of an atmospheric-pressure helium plasma jet

    NASA Astrophysics Data System (ADS)

    Yonemori, Seiya; Ono, Ryo; Oda, Tetsuji

    2012-10-01

    An atmospheric-pressure helium plasma jet is getting much attention because of its low heat load. It is known that active species such as OH radical play important role in many plasma processes, for example, in plasma medical care or in plasma sterilization. When using the plasma jet for surface treatment, it is important that the amount of OH radical provided into objectives. We measured OH density in the vicinity of the surface of objectives using laser induced fluorescence (LIF). The plasma jet was generated when AC 8 kHz, 10 kV was applied. When the plasma jet extended onto the dry glass surface, the maximum OH density was 0.2 ppm. On the other hand, the maximum OH density was 1 ppm when the plasma jet extended onto the wet surface. In addition, time-evolution of OH density between two successive voltage pulses was measured. On the edge of the plasma jet, OH density was at maximum and rapidly decreased between two pulses. Those results suggest that there are three ways of OH production; first, the dissociation of H2O included in discharge gas; secondly, the dissociation of H2O included in the ambient air; finally, the dissociation of H2O evaporates from the wet surface.

  15. Properties of Atmospheric Pressure Ar Plasma Jet Depending on Treated Dielectric Material

    NASA Astrophysics Data System (ADS)

    Prysiazhnyi, Vadym; Ricci Castro, Alonso H.; Kostov, Konstantin G.

    2017-02-01

    Atmospheric pressure plasma jet operated in argon was utilized to modify surfaces of glass, acrylic, and PTFE dielectrics. This paper describes the influence of the dielectric substrate on operation and properties of plasma. Two modes of operation (each of those have two patterns) were described. The transition from one mode to another, values of the dissipated power, and spreading of plasma over the dielectric surfaces strongly depended on the substrate material. Additionally, three methods of plasma spreading estimation were presented and discussed.

  16. DNA strand scission induced by a non-thermal atmospheric pressure plasma jet.

    PubMed

    Ptasińska, Sylwia; Bahnev, Blagovest; Stypczyńska, Agnieszka; Bowden, Mark; Mason, Nigel J; Braithwaite, Nicholas St J

    2010-07-28

    The DNA molecule is observed to be very susceptible to short-term exposures to an atmospheric pressure plasma jet. The DNA damage induced by plasma-generated species, i.e. excited atoms, charged particles, electrons and UV light is determined.

  17. Surface Modification of Material by Irradiation of Low Power Atmospheric Pressure Plasma Jet

    NASA Astrophysics Data System (ADS)

    Akamatsu, Hiroshi; Ichikawa, Kazunori; Azuma, Kingo; Onoi, Masahiro

    2010-10-01

    Application of a low power atmospheric pressure plasma jet for surface modifications of acrylic, aluminum, and highly crystalline graphite has been carried out experimentally. The plasma jet was generated with batteries-driven high voltage modulator. The power consumed for the plasma generation was estimated to be 0.12 W. The plasma had hydroxyl radicals, which is known as a strong oxider from an observation of optical emission spectrum. After the irradiation of the plasma, the surfaces of acrylic and aluminum became to be hydrophilic from the compartment of contact angle of water on these surfaces. The surface of highly crystalline graphite irradiated by the plasma jet had oxygen-rich functional groups such as C-O, C = O, and O = C-O.

  18. Sterilization of bacterial endospores by an atmospheric-pressure argon plasma jet

    NASA Astrophysics Data System (ADS)

    Uhm, Han S.; Lim, Jin P.; Li, Shou Z.

    2007-06-01

    Argon plasma jets penetrate deep into ambient air and create a path for oxygen radicals to sterilize microbes. A sterilization experiment with bacterial endospores indicates that an argon-oxygen plasma jet very effectively kills endospores of Bacillus atrophaeus (ATCC 9372), thereby demonstrating its capability to clean surfaces and its usefulness for reinstating contaminated equipment as free from toxic biological warfare agents. However, the spore-killing efficiency of the atmospheric-pressure argon-oxygen jet depends very sensitively on the oxygen concentration in the argon gas.

  19. Sterilization of bacterial endospores by an atmospheric-pressure argon plasma jet

    SciTech Connect

    Uhm, Han S.; Lim, Jin P.; Li, Shou Z.

    2007-06-25

    Argon plasma jets penetrate deep into ambient air and create a path for oxygen radicals to sterilize microbes. A sterilization experiment with bacterial endospores indicates that an argon-oxygen plasma jet very effectively kills endospores of Bacillus atrophaeus (ATCC 9372), thereby demonstrating its capability to clean surfaces and its usefulness for reinstating contaminated equipment as free from toxic biological warfare agents. However, the spore-killing efficiency of the atmospheric-pressure argon-oxygen jet depends very sensitively on the oxygen concentration in the argon gas.

  20. Cold atmospheric pressure plasma jets as sources of singlet delta oxygen for biomedical applications

    SciTech Connect

    Sousa, J. S.; Niemi, K.; Cox, L. J.; Algwari, Q. Th.; Gans, T.; O'Connell, D.

    2011-06-15

    Absolute densities of singlet delta oxygen (SDO) molecules were measured using infrared optical emission spectroscopy in the flowing effluents of two different atmospheric-pressure plasma jets (APPJs): a capacitively coupled radio-frequency-driven jet (rf-APPJ) and a lower frequency kilohertz-driven dielectric barrier discharge jet. The plasma jets were operated in helium, with small admixtures of molecular oxygen (O{sub 2} < 2%). High absolute SDO densities of up to 6.2 x 10{sup 15} cm{sup -3} were measured at approximately 10 cm downstream. The rf-APPJ seems to be much more efficient in producing SDO. The influence of different parameters, such as gas flows and mixtures and power coupled to the plasmas, on the production of SDO by the two APPJs has been investigated. Despite the considerable differences between the two plasma jets (excitation frequency, electric field direction, inter-electrode distance, plasma propagation), similar dependencies on the oxygen admixture and on the dissipated power were found in both APPJs. However, opposite trends were observed for the gas flow dependence. The results presented in this paper show that the control of the external operating conditions of each APPJ enables the tailoring of the SDO composition of both plasma effluents. This provides scope to tune the plasma jets for desired applications, e.g., in biomedicine.

  1. Development of a new atmospheric pressure cold plasma jet generator and application in sterilization

    NASA Astrophysics Data System (ADS)

    Cheng, Cheng; Liu, Peng; Xu, Lei; Zhang, Li-Ye; Zhan, Ru-Juan; Zhang, Wen-Rui

    2006-07-01

    This paper reports that a new plasma generator at atmospheric pressure, which is composed of two homocentric cylindrical all-metal tubes, successfully generates a cold plasma jet. The inside tube electrode is connected to ground, the outside tube electrode is connected to a high-voltage power supply, and a dielectric layer is covered on the outside tube electrode. When the reactor is operated by low-frequency (6 kHz-20 kHz) AC supply in atmospheric pressure and argon is steadily fed as a discharge gas through inside tube electrode, a cold plasma jet is blown out into air and the plasma gas temperature is only 25-30°C. The electric character of the discharge is studied by using digital real-time oscilloscope (TDS 200-Series), and the discharge is capacitive. Preliminary results are presented on the decontamination of E.colis bacteria and Bacillus subtilis bacteria by this plasma jet, and an optical emission analysis of the plasma jet is presented in this paper. The ozone concentration generated by the plasma jet is 1.0×1016cm-3 which is acquired by using the ultraviolet absorption spectroscopy.

  2. Atmospheric pressure plasma jet with high-voltage power supply based on piezoelectric transformer.

    PubMed

    Babij, Michał; Kowalski, Zbigniew W; Nitsch, Karol; Silberring, Jerzy; Gotszalk, Teodor

    2014-05-01

    The dielectric barrier discharge plasma jet, an example of the nonthermal atmospheric pressure plasma jet (APPJ), generates low-temperature plasmas that are suitable for the atomization of volatile species and can also be served as an ionization source for ambient mass and ion mobility spectrometry. A new design of APPJ for mass spectrometry has been built in our group. In these plasma sources magnetic transformers (MTs) and inductors are typically used in power supplies but they present several drawbacks that are even more evident when dealing with high-voltage normally used in APPJs. To overcome these disadvantages, high frequency generators with the absence of MT are proposed in the literature. However, in the case of miniaturized APPJs these conventional power converters, built of ferromagnetic cores and inductors or by means of LC resonant tank circuits, are not so useful as piezoelectric transformer (PT) based power converters due to bulky components and small efficiency. We made and examined a novel atmospheric pressure plasma jet with PT supplier served as ionization source for ambient mass spectrometry, and especially mobile spectrometry where miniaturization, integration of components, and clean plasma are required. The objective of this paper is to describe the concept, design, and implementation of this miniaturized piezoelectric transformer-based atmospheric pressure plasma jet.

  3. Atmospheric pressure plasma jet with high-voltage power supply based on piezoelectric transformer

    SciTech Connect

    Babij, Michał; Kowalski, Zbigniew W. Nitsch, Karol; Gotszalk, Teodor; Silberring, Jerzy

    2014-05-15

    The dielectric barrier discharge plasma jet, an example of the nonthermal atmospheric pressure plasma jet (APPJ), generates low-temperature plasmas that are suitable for the atomization of volatile species and can also be served as an ionization source for ambient mass and ion mobility spectrometry. A new design of APPJ for mass spectrometry has been built in our group. In these plasma sources magnetic transformers (MTs) and inductors are typically used in power supplies but they present several drawbacks that are even more evident when dealing with high-voltage normally used in APPJs. To overcome these disadvantages, high frequency generators with the absence of MT are proposed in the literature. However, in the case of miniaturized APPJs these conventional power converters, built of ferromagnetic cores and inductors or by means of LC resonant tank circuits, are not so useful as piezoelectric transformer (PT) based power converters due to bulky components and small efficiency. We made and examined a novel atmospheric pressure plasma jet with PT supplier served as ionization source for ambient mass spectrometry, and especially mobile spectrometry where miniaturization, integration of components, and clean plasma are required. The objective of this paper is to describe the concept, design, and implementation of this miniaturized piezoelectric transformer-based atmospheric pressure plasma jet.

  4. Atmospheric pressure plasma jet with high-voltage power supply based on piezoelectric transformer

    NASA Astrophysics Data System (ADS)

    Babij, Michał; Kowalski, Zbigniew W.; Nitsch, Karol; Silberring, Jerzy; Gotszalk, Teodor

    2014-05-01

    The dielectric barrier discharge plasma jet, an example of the nonthermal atmospheric pressure plasma jet (APPJ), generates low-temperature plasmas that are suitable for the atomization of volatile species and can also be served as an ionization source for ambient mass and ion mobility spectrometry. A new design of APPJ for mass spectrometry has been built in our group. In these plasma sources magnetic transformers (MTs) and inductors are typically used in power supplies but they present several drawbacks that are even more evident when dealing with high-voltage normally used in APPJs. To overcome these disadvantages, high frequency generators with the absence of MT are proposed in the literature. However, in the case of miniaturized APPJs these conventional power converters, built of ferromagnetic cores and inductors or by means of LC resonant tank circuits, are not so useful as piezoelectric transformer (PT) based power converters due to bulky components and small efficiency. We made and examined a novel atmospheric pressure plasma jet with PT supplier served as ionization source for ambient mass spectrometry, and especially mobile spectrometry where miniaturization, integration of components, and clean plasma are required. The objective of this paper is to describe the concept, design, and implementation of this miniaturized piezoelectric transformer-based atmospheric pressure plasma jet.

  5. Electronic ground state OH(X) radical in a low-temperature atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Fuh, Che A.; Clark, Shane M.; Wu, Wei; Wang, Chuji

    2016-10-01

    The wide applicability of atmospheric pressure plasma jets in biomedicine stems from the presence of reactive nitrogen and oxygen species generated in these plasma jets. Knowing the absolute concentration of these reactive species is of utmost importance as it is critical, along with the particle flux obtained from the plasma feed gas flow rate to ensure that the correct dosage is applied during applications. In this study, we investigate and report the ground state OH(X) number density acquired using cavity ringdown spectroscopy, along the propagation axis (z-axis) of a cold atmospheric pressure helium plasma plume. The jet was generated by a repetitively pulsed mono-polar square wave of duration 1 μs running at a frequency of 9.9 kHz. The voltage supplied was 6.5 kV with the helium flow rate fixed at 3.6 standard liters per minute. The rotational and vibrational temperatures are simulated from the second positive system of nitrogen, N 2(C3πu-B3πg) , with the rotational temperature being spatially constant at 300 K along the propagation axis of the atmospheric pressure plasma jet while the vibrational temperature is 3620 K at the beginning of the plume and is observed to decrease downstream. The OH(A) emission intensity obtained via optical emission spectroscopy was observed to decrease downstream of the plasma jet. The OH(X) number density along the propagation axis was initially 2.2 × 1013 molecules cm-3 before increasing to a peak value of 2.4 × 1013 molecules cm-3, from which the number density was observed to decrease to 2.2 × 1013 molecules cm-3 downstream of the plasma jet. The total OH(A, X) in the plasma jet remained relatively constant along the propagation axis of the plasma jet before falling off at the tip of the jet. The increase in vibrational temperature downstream and the simultaneous measurements of both the excited state OH(A) and the ground state OH(X) reported in this study provide insights into the formation and consumption of this

  6. Microwave-excited atmospheric-pressure plasma jets using a microstrip line

    SciTech Connect

    Kim, Jaeho; Katsurai, Makoto; Kim, Dongmin; Ohsaki, Hyroyuki

    2008-11-10

    We report a 2.45 GHz microwave-excited atmospheric-pressure plasma jet (MW-APPJ) device using a microstrip line for materials processing. A three-dimensional simulation based on the finite difference time domain method revealed that the configuration of the MW-APPJ device results in a strong concentration of electric fields at the gas nozzle. Argon plasmas were generated at the nozzle and were blown into ambient air with the maximum length of 5 mm at a microwave power of 40 W. The rotational temperatures of molecular nitrogen in the downstream of the plasma jets, measured by optical emission spectroscopy, were 1720 to 900 K for gas flow rates from 0.5 to 3.5 l/min, indicating that the jets were nonthermal plasmas. This MW-APPJ device will provide a large-area APPJ for materials processing depending on the configuration of the nozzle array and microstrip lines.

  7. Microbicidal activities of low frequency atmospheric pressure plasma jets on oral pathogens.

    PubMed

    Yamazaki, Hiromitsu; Ohshima, Tomoko; Tsubota, Yuji; Yamaguchi, Hiroyasu; Jayawardena, Jayanetti Asiri; Nishimura, Yasushi

    2011-01-01

    Research using low frequency atmospheric pressure plasma jets (LF jet) is becoming increasingly more common. We carried out experiments to evaluate the sterilizing effects of this technology on oral pathogenic microorganisms (S.mutans, C.albicans and E. faecalis) and to determine its potential for clinical application. We performed the direct exposure test on a solid surface, indirect exposure test on a liquid phase, and ROS (reactive oxygen species) inhibitory test. The results showed the LF jet had microbicidal effects on oral pathogens, and that the ROS influenced this sterilization effect. The experiments of this study revealed that LF jet had a sterilizing effect on oral pathogenic microorganisms present in both the solid and liquid phases. The sterilizing mechanism was considered to be related to the effect of superoxide anion radicals. These results indicate that LF jets may represent a novel technology that can be applied to the field of clinical dentistry.

  8. A low power miniaturized dielectric barrier discharge based atmospheric pressure plasma jet.

    PubMed

    Divya Deepak, G; Joshi, N K; Pal, Dharmendra Kumar; Prakash, Ram

    2017-01-01

    In this paper, a dielectric barrier discharge plasma based atmospheric pressure plasma jet has been generated in a floating helix and floating end ring electrode configuration using argon and helium gases. This configuration is subjected to a range of supply frequencies (10-25 kHz) and supply voltages (2-6 kV) at a fixed rate of gas flow rate (i.e., 1 l/min). The electrical characterization of the plasma jet has been carried out using a high voltage probe and current transformer. The current-voltage characteristics have been analyzed, and the consumed power has been estimated at different applied combinations for optimum power consumption at maximum jet length. The obtained optimum power and jet length for argon and helium gases are 12 mW and 32 mm, and 7.7 mW and 42 mm, respectively. It is inferred that besides the electrode configurations, the discharge gas is also playing a significant role in the low power operation of the cold plasma jet at maximum jet length. The obtained results are interpreted on the basis of penning processes.

  9. A low power miniaturized dielectric barrier discharge based atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Divya Deepak, G.; Joshi, N. K.; Pal, Dharmendra Kumar; Prakash, Ram

    2017-01-01

    In this paper, a dielectric barrier discharge plasma based atmospheric pressure plasma jet has been generated in a floating helix and floating end ring electrode configuration using argon and helium gases. This configuration is subjected to a range of supply frequencies (10-25 kHz) and supply voltages (2-6 kV) at a fixed rate of gas flow rate (i.e., 1 l/min). The electrical characterization of the plasma jet has been carried out using a high voltage probe and current transformer. The current-voltage characteristics have been analyzed, and the consumed power has been estimated at different applied combinations for optimum power consumption at maximum jet length. The obtained optimum power and jet length for argon and helium gases are 12 mW and 32 mm, and 7.7 mW and 42 mm, respectively. It is inferred that besides the electrode configurations, the discharge gas is also playing a significant role in the low power operation of the cold plasma jet at maximum jet length. The obtained results are interpreted on the basis of penning processes.

  10. Atmospheric pressure resistive barrier air plasma jet induced bacterial inactivation in aqueous environment

    NASA Astrophysics Data System (ADS)

    Thiyagarajan, Magesh; Sarani, Abdollah; Gonzales, Xavier

    2013-03-01

    An atmospheric pressure resistive barrier air plasma jet is designed to inactivate bacteria in aqueous media in direct and indirect exposure modes of treatment. The resistive barrier plasma jet is designed to operate at both dc and standard 50-60 Hz low frequency ac power input and the ambient air at 50% humidity level was used as the operating gas. The voltage-current characteristics of the plasma jet were analyzed and the operating frequency of the discharge was measured to be 20 kHz and the plasma power was measured to be 26 W. The plasma jet rotational temperatures (Trot) are obtained from the optical emission spectra, from the N2C-B(2+) transitions by matching the experimental spectrum results with the Spectra Air (SPECAIR) simulation spectra. The reactive oxygen and nitrogen species were measured using optical emission spectroscopy and gas analyzers, for direct and indirect treatment modes. The nitric oxides (NO) were observed to be the predominant long lived reactive nitrogen species produced by the plasma. Three different bacteria including Staphylococcus aureus (Gram-positive), Escherichia coli (Gram-negative), and Neisseria meningitidis (Gram-negative) were suspended in an aqueous media and treated by the resistive barrier air plasma jet in direct and indirect exposure modes. The results show that a near complete bacterial inactivation was achieved within 120 s for both direct and indirect plasma treatment of S. aureus and E. coli bacteria. Conversely, a partial inactivation of N. meningitidis was observed by 120 s direct plasma exposure and insignificant inactivation was observed for the indirect plasma exposure treatment. Plasma induced shifts in N. meningitidis gene expression was analyzed using pilC gene expression as a representative gene and the results showed a reduction in the expression of the pilC gene compared to untreated samples suggesting that the observed protection against NO may be regulated by other genes.

  11. Numerical study of the interaction of a helium atmospheric pressure plasma jet with a dielectric material

    NASA Astrophysics Data System (ADS)

    Wang, Lijun; Zheng, Yashuang; Jia, Shenli

    2016-10-01

    This is a computational modeling study of a cold atmospheric pressure helium plasma jet impinging on a dielectric surface placed normal to the jet axis. This study provides insights into the propagation mechanism of the plasma jet, the electrical properties, and the total accumulated charge density at the dielectric surface. For the radial streamer propagation along the dielectric surface, Penning ionization and the electron impact ionization of helium atoms are the major ionization reactions in the streamer head, while Penning ionization is the only dominant contributor along the streamer body. In addition, the plasma bullet velocity along the dielectric surface is 10-100 times lower than that in the plasma column. Increasing tube radius or helium flow rate lowers air entrainment in the plasma jet, leading to a decrease of the radial electric field and the accumulated charge density at the dielectric surface. Furthermore, the tube radius has weaker influence on the plasma properties as tube radius increases. For a target dielectric with lower relative permittivity, a higher radial electric field penetrates into the material, and the surface ionization wave along the dielectric surface extends farther. Higher relative permittivity of the treated dielectric results in more charging at the dielectric surface and more electron density in the plasma column.

  12. Atmospheric pressure plasma jets interacting with liquid covered tissue: touching and not-touching the liquid

    NASA Astrophysics Data System (ADS)

    Norberg, Seth A.; Tian, Wei; Johnsen, Eric; Kushner, Mark J.

    2014-11-01

    In the use of atmospheric pressure plasma jets in biological applications, the plasma-produced charged and neutral species in the plume of the jet often interact with a thin layer of liquid covering the tissue being treated. The plasma-produced reactivity must then penetrate through the liquid layer to reach the tissue. In this computational investigation, a plasma jet created by a single discharge pulse at three different voltages was directed onto a 200 µm water layer covering tissue followed by a 10 s afterglow. The magnitude of the voltage and its pulse length determined if the ionization wave producing the plasma plume reached the surface of the liquid. When the ionization wave touches the surface, significantly more charged species were created in the water layer with H3O+aq, O3-aq, and O2-aq being the dominant terminal species. More aqueous OHaq, H2O2aq, and O3aq were also formed when the plasma plume touches the surface. The single pulse examined here corresponds to a low repetition rate plasma jet where reactive species would be blown out of the volume between pulses and there is not recirculation of flow or turbulence. For these conditions, NxOy species do not accumulate in the volume. As a result, aqueous nitrites, nitrates, and peroxynitrite, and the HNO3aq and HOONOaq, which trace their origin to solvated NxOy, have low densities.

  13. Atmospheric pressure He-air plasma jet: Breakdown process and propagation phenomenon

    SciTech Connect

    Begum, Asma; Laroussi, Mounir; Pervez, Mohammad Rasel

    2013-06-15

    In this paper He-discharge (plasma jet/bullet) in atmospheric pressure air and its progression phenomenon has been studied experimentally using ICCD camera, optical emission spectroscopy (OES) and calibrated dielectric probe measurements. The repetitive nanosecond pulse has applied to a plasma pencil to generate discharge in the helium gas channel. The discharge propagation speed was measured from the ICCD images. The axial electric field distribution in the plasma jet is inferred from the optical emission spectroscopic data and from the probe measurement. The correlation between the jet velocities, jet length with the pulse duration is established. It shows that the plasma jet is not isolated from the input voltage along its propagation path. The discharge propagation speed, the electron density and the local and average electric field distribution along the plasma jet axis predicted from the experimental results are in good agreement with the data predicted by numerical simulation of the streamer propagation presented in different literatures. The ionization phenomenon of the discharge predicts the key ionization parameters, such as speed, peak electric field in the front, and electron density. The maximum local electric field measured by OES is 95 kV/cm at 1.3 cm of the jet axis, and average EF measured by probe is 24 kV/cm at the same place of the jet. The average and local electron density estimated are in the order of 10{sup 11} cm{sup -3} and it reaches to the maximum of 10{sup 12} cm{sup -3}.

  14. Turbulent jet flow generated downstream of a low temperature dielectric barrier atmospheric pressure plasma device

    PubMed Central

    Whalley, Richard D.; Walsh, James L.

    2016-01-01

    Flowing low temperature atmospheric pressure plasma devices have been used in many technological applications ranging from energy efficient combustion through to wound healing and cancer therapy. The generation of the plasma causes a sudden onset of turbulence in the inhomogeneous axisymmetric jet flow downstream of the plasma plume. The mean turbulent velocity fields are shown to be self-similar and independent of the applied voltage used to generate the plasma. It is proposed that the production of turbulence is related to a combination of the small-amplitude plasma induced body forces and gas heating causing perturbations in the unstable shear layers at the jet exit which grow as they move downstream, creating turbulence. PMID:27561246

  15. Turbulent jet flow generated downstream of a low temperature dielectric barrier atmospheric pressure plasma device.

    PubMed

    Whalley, Richard D; Walsh, James L

    2016-08-26

    Flowing low temperature atmospheric pressure plasma devices have been used in many technological applications ranging from energy efficient combustion through to wound healing and cancer therapy. The generation of the plasma causes a sudden onset of turbulence in the inhomogeneous axisymmetric jet flow downstream of the plasma plume. The mean turbulent velocity fields are shown to be self-similar and independent of the applied voltage used to generate the plasma. It is proposed that the production of turbulence is related to a combination of the small-amplitude plasma induced body forces and gas heating causing perturbations in the unstable shear layers at the jet exit which grow as they move downstream, creating turbulence.

  16. Turbulent jet flow generated downstream of a low temperature dielectric barrier atmospheric pressure plasma device

    NASA Astrophysics Data System (ADS)

    Whalley, Richard D.; Walsh, James L.

    2016-08-01

    Flowing low temperature atmospheric pressure plasma devices have been used in many technological applications ranging from energy efficient combustion through to wound healing and cancer therapy. The generation of the plasma causes a sudden onset of turbulence in the inhomogeneous axisymmetric jet flow downstream of the plasma plume. The mean turbulent velocity fields are shown to be self-similar and independent of the applied voltage used to generate the plasma. It is proposed that the production of turbulence is related to a combination of the small-amplitude plasma induced body forces and gas heating causing perturbations in the unstable shear layers at the jet exit which grow as they move downstream, creating turbulence.

  17. Study of an Atmospheric Pressure Plasma Jet of Argon Generated by Column Dielectric Barrier Discharge

    NASA Astrophysics Data System (ADS)

    Nur, M.; Kinandana, A. W.; Winarto, P.; Muhlisin, Z.; Nasrudin

    2016-11-01

    An atmospheric of argon plasma jet was generated by using column dielectric barrier discharge has been investigated. In this study, argon gas was passed through the capillary column by regulating the flow rate of gas. This atmospheric pressure plasma jet (APPJ) was generated by a sinusoidal AC high voltage in the range of 0.4 kV to 10 kV and at frequencies of 15 kHz and 26 kHz. APPJ has been produced with flow rate of argon gas from 1 litter/min - 10 litters/min. The electric current has been taken with variation of voltage and each interval argon gas flow rate of 1 litter/min. The results show that electric current increase linearly and then it trends to saturation condition by the increasing of applied voltage. We found also that the length of the plasma jet increase by augmenting of applied voltage both for frequencies of 15 kHz and 26 kHz. Furthermore, our results show that length of plasma jet optimum for flow rate of argon gas of 2 litters/minute. In addition, we obtained that the larger applied voltage, the greater the temperature of the plasma jet.

  18. Bullet-to-streamer transition on the liquid surface of a plasma jet in atmospheric pressure

    NASA Astrophysics Data System (ADS)

    Yoon, S.-Y.; Kim, G.-H.; Kim, S.-J.; Bae, B.; Kim, N.-K.; Lee, H.; Bae, N.; Ryu, S.; Yoo, S. J.; Kim, S. B.

    2017-01-01

    This study investigated the transition of the plasma shape from a ring-shaped bullet to a pin-like streamer adjacent to the electrolyte surface in a kHz-driven helium atmospheric pressure plasma jet. The transition was observed by synchronized fast images, plasma propagation speed, time-resolved emission profile of Hβ, and spatially and temporally resolved helium metastable density. The transition height increased when electrolyte evaporation was enhanced. The plasma continued to discharge on the electrolyte surface even in the absence of metastable species, i.e., the discharge mechanism changed from Penning ionization between helium metastable and ambient nitrogen to electron collision on evaporated water.

  19. Electrical and optical properties of Ar/NH3 atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Chang, Zheng-Shi; Yao, Cong-Wei; Chen, Si-Le; Zhang, Guan-Jun

    2016-09-01

    Inspired by the Penning effect, we obtain a glow-like plasma jet by mixing ammonia (NH3) into argon (Ar) gas under atmospheric pressure. The basic electrical and optical properties of an atmospheric pressure plasma jet (APPJ) are investigated. It can be seen that the discharge mode transforms from filamentary to glow-like when a little ammonia is added into the pure argon. The electrical and optical analyses contribute to the explanation of this phenomenon. The discharge mode, power, and current density are analyzed to understand the electrical behavior of the APPJ. Meanwhile, the discharge images, APPJ's length, and the components of plasma are also obtained to express its optical characteristics. Finally, we diagnose several parameters, such as gas temperature, electron temperature, and density, as well as the density number of metastable argon atoms of Ar/NH3 APPJ to help judge the usability in its applications.

  20. The plasma footprint of an atmospheric pressure plasma jet on a flat polymer substrate and its relation to surface treatment

    NASA Astrophysics Data System (ADS)

    Onyshchenko, Iuliia; Nikiforov, Anton Yu.; De Geyter, Nathalie; Morent, Rino

    2016-08-01

    The aim of this work is to show the correlation between the plasma propagation in the footprint of an atmospheric pressure plasma jet on a flat polymer surface and the plasma treatment impact on the polymer properties. An argon plasma jet working in open air is used as plasma source, while PET thin films are used a substrates for plasma treatment. Light emission photographs are taken with an ICCD camera to have a close look at the generated structures in the plasma jet footprint on the surface. Water contact angle (WCA) measurement and X-ray photoelectron spectroscopy (XPS) analysis are also performed to obtain information about the impact of the plasma treatment on the PET surface characteristics. A variation in ICCD camera gate duration (1 µs, 100 µs, 50 ms) results in the photographs of the different plasma structures occurring during the plasma propagation on the flat PET surface. Contact angle measurements provide results on improvement of the PET hydrophilic character, while XPS analysis shows the distribution of atomic elements on the treated substrate surface. Light emission images help explaining the obtained WCA and XPS results. Contribution to the topical issue "6th Central European Symposium on Plasma Chemistry (CESPC-6)", edited by Nicolas Gherardi, Ester Marotta and Cristina Paradisi

  1. Characterization of an atmospheric pressure plasma jet and its applications for disinfection and cancer treatment.

    PubMed

    Thiyagarajan, Magesh; Sarani, Abdollah; Gonzales, Xavier F

    2013-01-01

    In this work an atmospheric pressure non-thermal resistive barrier (RB) plasma jet was constructed, characterized and was applied for biomedical applications. The RB plasma source can operate in both DC (battery) as well as in standard 60/50 Hz low frequency AC excitation, and it functions effectively in both direct and indirect plasma exposure configurations. The characteristics of the RB plasma jet such as electrical properties, plasma gas temperature and nitric oxides concentration were determined using voltage-current characterization, optical emission spectroscopy and gas analyzer diagnostic techniques. Plasma discharge power of 26.33 W was calculated from voltage-current characterization. An optical emission spectroscopy was applied and the gas temperature which is equivalent to the nitrogen rotational (Trot) temperatures was measured. The concentrations of the reactive oxygen species at different spatial distances from the tip of the plasma jet were measured and the ppm concentration of NO is at the preferred level for a wide range of standard biomedical treatment applications. The ppm values of nitric oxides after the cooling unit are observed to be of the same order of magnitude as compared to plasma jet. The portable RB plasma source was tested to be very effective for decontamination and disinfection of a wide range of foodborne and opportunistic nosocomial pathogens such as Escherichia coli, Staphylococcus aureus, Pseudomonas aeruginosa and Bacillus cereus and the preliminary results are presented. The effects of indirect exposure of the portable RBP source on monocytic leukemia cancer cells (THP-1) were also tested and the results demonstrate that a preference for apoptosis in plasma treated THP-1 cells under particular plasma parameters and dosage levels.

  2. Effect of cold atmospheric pressure He-plasma jet on DNA change and mutation

    NASA Astrophysics Data System (ADS)

    Yaopromsiri, C.; Yu, L. D.; Sarapirom, S.; Thopan, P.; Boonyawan, D.

    2015-12-01

    Cold atmospheric pressure plasma jet (CAPPJ) effect on DNA change was studied for assessment of its safety. The experiment utilized a home-developed CAPPJ using 100% helium to directly treat naked DNA plasmid pGFP (plasmid green fluorescent protein). A traversal electric field was applied to separate the plasma components and both dry and wet sample conditions were adopted to investigate various factor roles in changing DNA. Plasma species were measured by using optical emission spectroscopy. DNA topological form change was analyzed by gel electrophoresis. The plasma jet treated DNA was transferred into bacterial Escherichia coli cells for observing mutation. The results show that the He-CAPPJ could break DNA strands due to actions from charge, radicals and neutrals and potentially cause genetic modification of living cells.

  3. [Comparative study on the gas temperature of a plasma jet at atmospheric pressure].

    PubMed

    Jia, Peng-Ying; Li, Xue-Chen; Yuan, Ning

    2011-08-01

    A plasma jet of a dielectric barrier discharge in coaxial electrode was used to produce jet plasma in flowing work gas (argon mixed with trace nitrogen) at atmospheric pressure. The relation between the plasma length and the gas flow rate was obtained by taking the images of the jet plasma. A high-resolution optical spectrometer was used to collect the optical emission spectrum. The emission spectra of the first negative band of N(2+) (B2 Sigma(u+)-->Chi2 Sigma(g+), 390-391.6 nm) were used to estimate the rotational temperature of the plasma plume by fitting the experimental spectra to the simulated spectra. The gas temperature was investigated by this optical method and results show that the gas temperature increases with increasing the applied voltage. For comparison, a thermometer was used to measure the temperature of the gas emitted from the jet. The results also show that the gas temperature increases with increasing the applied voltage. The gas temperatures obtained by the two methods are consistent. The difference was analyzed.

  4. 3D Mapping of plasma effective areas via detection of cancer cell damage induced by atmospheric pressure plasma jets

    NASA Astrophysics Data System (ADS)

    Han, Xu; Liu, Yueing; Stack, M. Sharon; Ptasinska, Sylwia

    2014-12-01

    In the present study, a nitrogen atmospheric pressure plasma jet (APPJ) was used for irradiation of oral cancer cells. Since cancer cells are very susceptible to plasma treatment, they can be used as a tool for detection of APPJ-effective areas, which extended much further than the visible part of the APPJ. An immunofluorescence assay was used for DNA damage identification, visualization and quantification. Thus, the effective damage area and damage level were determined and plotted as 3D images.

  5. Cavity-enhanced absorption spectroscopy to characterize atmospheric pressure plasma jets

    NASA Astrophysics Data System (ADS)

    van Helden, Jean-Pierre; Nave, Andy; Reuter, Stephan; Roepcke, Juergen; Gianella, Michele; Ritchie, Grant

    2016-09-01

    Non-equilibrium atmospheric pressure plasma jets gain more and more interest as their technological applications increase in diverse fields such as material processing and plasma medicine. Hence, it is essential to diagnose the fluxes of the species generated by these plasma sources to identify relevant fundamental processes and to improve process efficiency. Especially for a comprehensive understanding of the kinetics of the transient species involved, high precision measurements of reactive molecular precursors, free radicals and to identify of any short lived species are of crucial importance. However, the detection of transient species in these type of plasmas poses a challenge for diagnostic techniques as the plasmas typically have small dimensions and high density gradients in space and time. We have overcome these limitations by using cavity-enhanced absorption spectroscopy (CEAS). In this contribution, the latest results concerning the detection of transient species in two types of plasma jets employing CEAS in the near- and mid-infrared spectral range will be presented. We will show that with these methods spatially resolved investigations of concentrations in the mm sized effluent of the plasma jet can be achieved.

  6. DNA damage in oral cancer cells induced by nitrogen atmospheric pressure plasma jets

    SciTech Connect

    Han, Xu; Ptasinska, Sylwia; Klas, Matej; Liu, Yueying; Sharon Stack, M.

    2013-06-10

    The nitrogen atmospheric pressure plasma jet (APPJ) was applied to induce DNA damage of SCC-25 oral cancer cells. Optical emission spectra were taken to characterize the reactive species produced in APPJ. In order to explore the spatial distribution of plasma effects, cells were placed onto photo-etched grid slides and the antibody H2A.X was used to locate double strand breaks of DNA inside nuclei using an immunofluorescence assay. The number of cells with double strand breaks in DNA was observed to be varied due to the distance from the irradiation center and duration of plasma treatment.

  7. Atmospheric pressure plasma jet for bacterial decontamination and property improvement of fruit and vegetable processing wastewater

    NASA Astrophysics Data System (ADS)

    Mohamed, Abdel-Aleam H.; Shariff, Samir M. Al; Ouf, Salama A.; Benghanem, Mohamed

    2016-05-01

    An atmospheric pressure plasma jet was tested for decontaminating and improving the characteristics of wastewater derived from blackberry, date palm, tomato and beetroot processing industries. The jet was generated by blowing argon gas through a cylindrical alumina tube while a high voltage was applied between two electrodes surrounding the tube. Oxygen gas was mixed with argon at the rate of 0.2% and the argon mass flow was fixed at 4.5 slm. Images show that the generated plasma jet penetrated the treated wastewater samples. Plasma emission spectra show the presence of O and OH radicals as well as excited molecular nitrogen and argon. Complete decontamination of wastewater derived from date palm and tomato processing was achieved after 120 and 150 s exposure to the plasma jet, respectively. The bacterial count of wastewater from blackberry and beetroot was reduced by 0.41 and 2.24 log10 colony-forming units (CFU) per ml, respectively, after 180 s. Escherichia coli was the most susceptible bacterial species to the cold plasma while Shigella boydii had the minimum susceptibility, recording 1.30 and 3.34 log10 CFU ml-1, respectively, as compared to the 7.00 log10 initial count. The chemical oxygen demands of wastewater were improved by 57.5-93.3% after 180 s exposure to the plasma jet being tested. The endotoxins in the wastewater were reduced by up to 90.22%. The variation in plasma effectiveness is probably related to the antioxidant concentration of the different investigated wastewaters.

  8. Role of ambient dielectric in propagation of Ar atmospheric pressure nonequilibrium plasma jets

    SciTech Connect

    Song, Jian; Wang, Youyin; Yu, Daren; Tang, Jingfeng Wei, Liqiu; Ren, Chunsheng

    2015-05-15

    A single-electrode atmospheric pressure nonequilibrium plasma jet surrounded with different ambient dielectrics is investigated driven by AC power supply. Another three ambient dielectrics, distilled water, ethanol, and carbon tetrachloride, are adopted to compare with air. By examining electrical and optical characteristics, it was found that the molecular polarity of ambient dielectrics had its significant effect on the propagation of atmospheric pressure nonequilibrium plasma jets. When the polarization of molecules was enhanced, the discharge current and the bullet velocity were also increased. For nonpolar dielectric of carbon tetrachloride, this was mainly resulted from the electron polarization in the built-in electric field. For polar dielectrics of ethanol and distilled water, in addition to the electron polarization, orientation polarization was the main cause for the further increase in discharge current and bullet velocity.

  9. Surface Decontamination of Chemical Agent Surrogates Using an Atmospheric Pressure Air Flow Plasma Jet

    NASA Astrophysics Data System (ADS)

    Li, Zhanguo; Li, Ying; Cao, Peng; Zhao, Hongjie

    2013-07-01

    An atmospheric pressure dielectric barrier discharge (DBD) plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless steel or iron plate painted with alkyd or PVC. The experimental results of material decontamination show that the residual chemical agent on the material is lower than the permissible value of the National Military Standard of China. In order to test the corrosion effect of the plasma jet on different material surfaces in the decontamination process, corrosion tests for the materials of polymethyl methacrylate, neoprene, polyvinyl chloride (PVC), polyethylene (PE), phenolic resin, iron plate painted with alkyd, stainless steel, aluminum, etc. were carried out, and relevant parameters were examined, including etiolation index, chromatism, loss of gloss, corrosion form, etc. The results show that the plasma jet is slightly corrosive for part of the materials, but their performances are not affected. A portable calculator, computer display, mainboard, circuit board of radiogram, and a hygrometer could work normally after being treated by the plasma jet.

  10. Atmospheric-pressure plasma jet characterization and applications on melanoma cancer treatment (B/16-F10)

    SciTech Connect

    Mashayekh, Shahriar; Rajaee, Hajar; Hassan, Zuhir M.; Akhlaghi, Morteza; Shokri, Babak

    2015-09-15

    A new approach in medicine is the use of cold plasma for various applications such as sterilization blood coagulation and cancer cell treatment. In this paper, a pin-to-hole plasma jet for biological applications has been designed and manufactured and characterized. The characterization includes power consumption via Lissajous method, thermal behavior of atmospheric-pressure plasma jet by using Infra-red camera as a novel method and using Speicair software to determine vibrational and transitional temperatures, and optical emission spectroscopy to determine the generated species. Treatment of Melanoma cancer cells (B16/F10) was also implemented, and tetrazolium salt dye (MTT assay) and flow cytometry were used to evaluate viability. Effect of ultraviolet photons on cancerous cells was also observed using an MgF{sub 2} crystal with MTT assay. Finally, in-vivo studies on C57 type mice were also done in order to have a better understanding of the effects in real conditions.

  11. Atmospheric-pressure plasma jet characterization and applications on melanoma cancer treatment (B/16-F10)

    NASA Astrophysics Data System (ADS)

    Mashayekh, Shahriar; Rajaee, Hajar; Akhlaghi, Morteza; Shokri, Babak; Hassan, Zuhir M.

    2015-09-01

    A new approach in medicine is the use of cold plasma for various applications such as sterilization blood coagulation and cancer cell treatment. In this paper, a pin-to-hole plasma jet for biological applications has been designed and manufactured and characterized. The characterization includes power consumption via Lissajous method, thermal behavior of atmospheric-pressure plasma jet by using Infra-red camera as a novel method and using Speicair software to determine vibrational and transitional temperatures, and optical emission spectroscopy to determine the generated species. Treatment of Melanoma cancer cells (B16/F10) was also implemented, and tetrazolium salt dye (MTT assay) and flow cytometry were used to evaluate viability. Effect of ultraviolet photons on cancerous cells was also observed using an MgF2 crystal with MTT assay. Finally, in-vivo studies on C57 type mice were also done in order to have a better understanding of the effects in real conditions.

  12. [Sterilizing effect of atmospheric pressure plasma jet on microbes].

    PubMed

    Wu, Xu-Qin; Wang, Shou-guo; Han, Li; Zhao, Ling-li; Chang, Xiao; Chen, Geng; Suo, Ji-jiang; Xing, Yu-bin; Chen, Shi-ping

    2005-04-01

    To study the sterilizing effect and mechanism of APPJ on microbes preliminarily, three representative bacteria, Staphylococcus aureus, Escherichia coli, Bacillus subtilis var. niger were treated by two kinds of plasma, DBD (dielectric barrier discharge) and APPJ. The survival curves of different microbes were compared and analyzed; Furthermore, the morphological change to cell walls and cell membranes were studied by scanning electric microscope. These results demonstrated that in the beginning phase the sterilizing effect of two kinds of plasmas on three microorganisms was stronger than in the later phase, and APPJ was more effective than DBD (D value of DBD on Bacillus subtilis var. niger was 70 s, whereas APPJ's was 4 s, much more efficient). Meanwhile, the gross morphological damage of E. coli cells under SEM after APPJ treatment was observed. These gave the obvious evidence that APPJ can destroy the microbes very efficiently, and more likely through the damage of cell walls and membranes of microbes treated by APPJ.

  13. Characterizations of atmospheric pressure low temperature plasma jets and their applications

    NASA Astrophysics Data System (ADS)

    Karakas, Erdinc

    2011-12-01

    Atmospheric pressure low temperature plasma jets (APLTPJs) driven by short pulses have recently received great attention because of their potential in biomedical and environmental applications. This potential is due to their user-friendly features, such as low temperature, low risk of arcing, operation at atmospheric pressure, easy handheld operation, and low concentration of ozone generation. Recent experimental observations indicate that an ionization wave exists and propagates along the plasma jet. The plasma jet created by this ionization wave is not a continuous medium but rather consists of a bullet-like-structure known as "Plasma Bullet". More interestingly, these plasma bullets actually have a donut-shaped makeup. The nature of the plasma bullet is especially interesting because it propagates in the ambient air at supersonic velocities without any externally applied electric field. In this dissertation, experimental insights are reported regarding the physical and chemical characteristics of the APLTPJs. The dynamics of the plasma bullet are investigated by means of a high-speed ICCD camera. A plasma bullet propagation model based on the streamer theory is confirmed with adequate explanations. It is also found that a secondary discharge, ignited by the charge accumulation on the dielectric electrode surfaces at the end of the applied voltage, interrupts the plasma bullet propagation due to an opposing current along the ionization channel. The reason for this interesting phenomenon is explained in detail. The plasma bullet comes to an end when the helium mole fraction along the ionization channel, or applied voltage, or both, are less than some critical values. The presence of an inert gas channel in the surrounding air, such as helium or argon, has a critical role in plasma bullet formation and propagation. For this reason, a fluid dynamics study is employed by a commercially available simulation software, COMSOL, based on finite element method. Spatio

  14. Controlling the nitric and nitrous oxide production of an atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Douat, Claire; Hubner, Simon; Engeln, Richard; Benedikt, Jan

    2016-09-01

    Atmospheric pressure plasma jets are non-thermal plasmas and have the ability to create reactive species. These features make it a very attractive tool for biomedical applications. In this work, we studied NO and N2O production, which are two species having biomedical properties. NO plays a role in the vascularization and in ulcer treatment, while N2O is used as anesthetic and analgesic gas. In this study, the plasma source is similar to the COST Reference Microplasma Jet (µ-APPJ). Helium is used as feed gas with small admixtures of molecular nitrogen and oxygen of below 1%. The absolute densities of NO and N2O were measured in the effluent of an atmospheric pressure RF plasma jet by means of ex-situ quantum-cascade laser absorption spectroscopy via a multi-pass cell in Herriot configuration. We will show that the species' production is dependent on several parameters such as power, flow and oxygen and nitrogen admixture. The NO and N2O densities are strongly dependent on the N2-O2 ratio. Changing this ratio allows for choosing between a NO-rich or a N2O-rich regime.

  15. Power dissipated in a non-thermal atmospheric pressure plasma jet measured by miniaturized electrical probes

    NASA Astrophysics Data System (ADS)

    Golda, Judith; Schulz-von der Gathen, Volker

    2016-09-01

    Non-thermal atmospheric pressure plasma jets are used in bio-medicine, because they generate reactive species at a low gas temperature. Knowledge and control of plasma parameters is required for stable and reliable operation. Therefore, measuring dissipated power in these plasmas is necessary. However, this is challenging because the delivered sender power is often orders of magnitudes higher than the power dissipated in the discharge itself. To measure this dissipated power, we built miniaturized electrical probes directly attached to the jet device. We observed that the dissipated power is a more comprehensive parameter than the common parameter voltage: For example, gas temperature and emission line intensities rose exponentially with increasing voltage but linearly with increasing power. Our analyses further revealed that a substantial proportion of the dissipated power is transformed into heat. In conclusion, miniaturized electrical probes give a fundamental insight into the energy balance of atmospheric pressure plasmas. In the future, these probes can also be adapted to different types of atmospheric pressure plasmas. This work was supported by DFG within the frameworks of the Package Project PAK 816.

  16. Atomic oxygen behavior at downstream of AC excited atmospheric pressure He plasma jet

    NASA Astrophysics Data System (ADS)

    Takeda, Keigo; Ishikawa, Kenji; Tanaka, Hiromasa; Sekine, Makoto; Hori, Masaru

    2016-09-01

    Applications of atmospheric pressure plasma jets (APPJ) have been investigated in the plasma medical fields such as cancer therapy, blood coagulation, etc. Reactive species generated by the plasma jet interacts with the biological surface. Therefore, the issue attracts much attentions to investigate the plasma effects on targets. In our group, a spot-size AC excited He APPJ have been used for the plasma medicine. From diagnostics of the APPJ using optical emission spectroscopy, the gas temperature and the electron density was estimated to be 299 K and 3.4 ×1015 cm-3. The AC excited He APPJ which affords high density plasma at room temperature is considered to be a powerful tool for the medical applications. In this study, by using vacuum ultraviolet absorption spectroscopy, the density of atomic oxygen on a floating copper as a target irradiated by the He APPJ was measured as a function of the distance between the plasma source and the copper wire. The measured density became a maximum value around 8 ×1013 cm-3 at 12 mm distance, and then decreased over the distance. It is considered that the behavior was due to the changes in the plasma density on the copper wire and influence of ambient air.

  17. DNA damage in oral cancer cells induced by nitrogen atmospheric pressure plasma jets

    NASA Astrophysics Data System (ADS)

    Han, Xu; Klas, Matej; Liu, Yueying; Stack, M. Sharon; Ptasinska, Sylwia

    2013-09-01

    The nitrogen atmospheric pressure plasma jet (APPJ) has been shown to effectively induce DNA double strand breaks in SCC-25 oral cancer cells. The APPJ source constructed in our laboratory consists of two external electrodes wrapping around a quartz tube and nitrogen as a feed gas and operates based on dielectric barrier gas discharge. Generally, it is more challenging to ignite plasma in N2 atmosphere than in noble gases. However, this design provides additional advantages such as lower costs compared to the noble gases for future clinical operation. Different parameters of the APPJ configuration were tested in order to determine radiation dosage. To explore the effects of delayed damage and cell self-repairing, various incubation times of cells after plasma treatment were also performed. Reactive species generated in plasma jet and in liquid environment are essential to be identified and quantified, with the aim of unfolding the mystery of detailed mechanisms for plasma-induced cell apoptosis. Moreover, from the comparison of plasma treatment effect on normal oral cells OKF6T, an insight to the selectivity for cancer treatment by APPJ can be explored. All of these studies are critical to better understand the damage responses of normal and abnormal cellular systems to plasma radiation, which are useful for the development of advanced plasma therapy for cancer treatment at a later stage.

  18. Influence of oxygen in atmospheric-pressure argon plasma jet on sterilization of Bacillus atrophaeous spores

    NASA Astrophysics Data System (ADS)

    Lim, Jin-Pyo; Uhm, Han S.; Li, Shou-Zhe

    2007-09-01

    A nonequilibrium Ar /O2 plasma discharge at atmospheric pressure was carried out in a coaxial cylindrical reactor with a stepped electrode configuration powered by a 13.56MHz rf power supplier. The argon glow discharge with high electron density produces oxygen reactive species in large quantities. Argon plasma jets penetrate deep into ambient air and create a path for oxygen radicals to sterilize microbes. A sterilization experiment with bacterial endospores indicates that an argon-oxygen plasma jet very effectively kills endospores of Bacillus atrophaeus (ATCC 9372), thereby demonstrating its capability to clean surfaces and its usefulness for reinstating contaminated equipment as free from toxic biological warfare agents. The decimal reduction time (D values) of the Ar /O2 plasma jet at an exposure distance of 0.5-1.5cm ranges from 5 to 57s. An actinometric comparison of the sterilization data shows that atomic oxygen radicals play a significant role in plasma sterilization. When observed under a scanning electron microscope, the average size of the spores appears to be greatly reduced due to chemical reactions with the oxygen radicals.

  19. Influence of oxygen in atmospheric-pressure argon plasma jet on sterilization of Bacillus atrophaeous spores

    SciTech Connect

    Lim, Jin-Pyo; Uhm, Han S.; Li, Shou-Zhe

    2007-09-15

    A nonequilibrium Ar/O{sub 2} plasma discharge at atmospheric pressure was carried out in a coaxial cylindrical reactor with a stepped electrode configuration powered by a 13.56 MHz rf power supplier. The argon glow discharge with high electron density produces oxygen reactive species in large quantities. Argon plasma jets penetrate deep into ambient air and create a path for oxygen radicals to sterilize microbes. A sterilization experiment with bacterial endospores indicates that an argon-oxygen plasma jet very effectively kills endospores of Bacillus atrophaeus (ATCC 9372), thereby demonstrating its capability to clean surfaces and its usefulness for reinstating contaminated equipment as free from toxic biological warfare agents. The decimal reduction time (D values) of the Ar/O{sub 2} plasma jet at an exposure distance of 0.5-1.5 cm ranges from 5 to 57 s. An actinometric comparison of the sterilization data shows that atomic oxygen radicals play a significant role in plasma sterilization. When observed under a scanning electron microscope, the average size of the spores appears to be greatly reduced due to chemical reactions with the oxygen radicals.

  20. Atmospheric-pressure plasma jet induces apoptosis involving mitochondria via generation of free radicals.

    PubMed

    Ahn, Hak Jun; Kim, Kang Il; Kim, Geunyoung; Moon, Eunpyo; Yang, Sang Sik; Lee, Jong-Soo

    2011-01-01

    The plasma jet has been proposed as a novel therapeutic method for anticancer treatment. However, its biological effects and mechanism of action remain elusive. Here, we investigated its cell death effects and underlying molecular mechanisms, using air and N₂ plasma jets from a micro nozzle array. Treatment with air or N₂ plasma jets caused apoptotic death in human cervical cancer HeLa cells, simultaneously with depolarization of mitochondrial membrane potential. In addition, the plasma jets were able to generate reactive oxygen species (ROS), which function as surrogate apoptotic signals by targeting the mitochondrial membrane potential. Antioxidants or caspase inhibitors ameliorated the apoptotic cell death induced by the air and N₂ plasma jets, suggesting that the plasma jet may generate ROS as a proapoptotic cue, thus initiating mitochondria-mediated apoptosis. Taken together, our data suggest the potential employment of plasma jets as a novel therapy for cancer.

  1. Atmospheric-Pressure Plasma Jet Induces Apoptosis Involving Mitochondria via Generation of Free Radicals

    PubMed Central

    Kim, Geunyoung; Moon, Eunpyo; Yang, Sang Sik; Lee, Jong-Soo

    2011-01-01

    The plasma jet has been proposed as a novel therapeutic method for anticancer treatment. However, its biological effects and mechanism of action remain elusive. Here, we investigated its cell death effects and underlying molecular mechanisms, using air and N2 plasma jets from a micro nozzle array. Treatment with air or N2 plasma jets caused apoptotic death in human cervical cancer HeLa cells, simultaneously with depolarization of mitochondrial membrane potential. In addition, the plasma jets were able to generate reactive oxygen species (ROS), which function as surrogate apoptotic signals by targeting the mitochondrial membrane potential. Antioxidants or caspase inhibitors ameliorated the apoptotic cell death induced by the air and N2 plasma jets, suggesting that the plasma jet may generate ROS as a proapoptotic cue, thus initiating mitochondria-mediated apoptosis. Taken together, our data suggest the potential employment of plasma jets as a novel therapy for cancer. PMID:22140530

  2. Study on the Property Evolution of Atmospheric Pressure Plasma Jets in Helium

    NASA Astrophysics Data System (ADS)

    Chang, Zhengshi; Yao, Congwei; Mu, Haibao; Zhang, Guanjun

    2014-01-01

    Nowadays atmospheric pressure plasma jets (APPJs) are being widely applied to many fields and have received growing interests from cold plasma community. A helium APPJ with co-axial double ring electrode configuration is driven by an AC high voltage power with an adjustable frequency of 1-60 kHz. Experiments are conducted for acquiring the electrical and optical properties of APPJ, including the discharge mode, current peak's phase and APPJ's length, etc. Moreover, the actions of Penning effect on APPJ are discussed by adding impurity nitrogen into highly pure helium. The results may contribute to further research and applications of APPJs.

  3. LIF diagnostics of hydroxyl radical in a methanol containing atmospheric-pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Qian, Mu-Yang; Liu, San-Qiu; Pei, Xue-Kai; Lu, Xin-Pei; Zhang, Jia-Liang; Wang, De-Zhen

    2016-10-01

    In this paper, a pulsed-dc CH3OH/Ar plasma jet generated at atmospheric pressure is studied by laser-induced fluorescence (LIF) and optical emission spectroscopy (OES). A gas-liquid bubbler system is proposed to introduce the methanol vapor into the argon gas, and the CH3OH/Ar volume ratio is kept constant at about 0.1%. Discharge occurs in a 6-mm needle-to-ring gap in an atmospheric-pressure CH3OH/Ar mixture. The space-resolved distributions of OH LIF inside and outside the nozzle exhibit distinctly different behaviors. And, different production mechanisms of OH radicals in the needle-to-ring discharge gap and afterglow of plasma jet are discussed. Besides, the optical emission lines of carbonaceous species, such as CH, CN, and C2 radicals, are identified in the CH3OH/Ar plasma jet. Finally, the influences of operating parameters (applied voltage magnitude, pulse frequency, pulsewidth) on the OH radical density are also presented and analyzed. Project supported by the National Natural Science Foundation of China (Grant Nos. 11465013 and 11375041), the Natural Science Foundation of Jiangxi Province, China (Grant Nos. 20151BAB212012 and 20161BAB201013), and the International Science and Technology Cooperation Program of China (Grant No. 2015DFA61800).

  4. Emission spectroscopy of an atmospheric pressure plasma jet operated with air at low frequency

    NASA Astrophysics Data System (ADS)

    Giuliani, L.; Gallego, J. L.; Minotti, F.; Kelly, H.; Grondona, D.

    2015-03-01

    Low-temperature, high-pressure plasma jets have an extensive use in plasma biology and plasma medicine, such as pathogen deactivation, wound disinfection, stopping of bleeding without damage of healthy tissue, acceleration of wound healing, control of bio-film proliferation, etc. In this work, a spectroscopic characterization of a typical plasma jet, operated in air at atmospheric pressure, is reported. Within the spectrum of wavelengths from 200 to 450 nm all remarkable emissions of N2 were monitored. Spectra of the N2 2nd positive system (C3Πu-B3Πg) emitted in air are the most convenient for plasma diagnostics, since they enable to determine electronic Te, rotational Tr and vibrational Tv temperatures by fitting the experimental spectra with the simulated ones. We used SPECAIR software for spectral simulation and obtained the best fit with all these temperatures about 3500K. The conclusion that all temperatures are equal, and its relatively high value, is consistent with the results of a previous work, where it was found that the experimentally determined electrical characteristic was consistent with the model of a thermal arc discharge, together with a highly collisional cathode sheet.

  5. Inactivation of Gram-positive biofilms by low-temperature plasma jet at atmospheric pressure

    NASA Astrophysics Data System (ADS)

    Marchal, F.; Robert, H.; Merbahi, N.; Fontagné-Faucher, C.; Yousfi, M.; Romain, C. E.; Eichwald, O.; Rondel, C.; Gabriel, B.

    2012-08-01

    This work is devoted to the evaluation of the efficiency of a new low-temperature plasma jet driven in ambient air by a dc-corona discharge to inactivate adherent cells and biofilms of Gram-positive bacteria. The selected microorganisms were lactic acid bacteria, a Weissella confusa strain which has the particularity to excrete a polysaccharide polymer (dextran) when sucrose is present. Both adherent cells and biofilms were treated with the low-temperature plasma jet for different exposure times. The antimicrobial efficiency of the plasma was tested against adherent cells and 48 h-old biofilms grown with or without sucrose. Bacterial survival was estimated using both colony-forming unit counts and fluorescence-based assays for bacterial cell viability. The experiments show the ability of the low-temperature plasma jet at atmospheric pressure to inactivate the bacteria. An increased resistance of bacteria embedded within biofilms is clearly observed. The resistance is also significantly higher with biofilm in the presence of sucrose, which indicates that dextran could play a protective role.

  6. Langmuir probe diagnostics of an atmospheric pressure, vortex-stabilized nitrogen plasma jet

    SciTech Connect

    Prevosto, L.; Mancinelli, B. R.; Kelly, H.

    2012-09-15

    Langmuir probe measurements in an atmospheric pressure direct current (dc) plasma jet are reported. Sweeping probes were used. The experiment was carried out using a dc non-transferred arc torch with a rod-type cathode and an anode of 5 mm diameter. The torch was operated at a nominal power level of 15 kW with a nitrogen flow rate of 25 Nl min{sup -1}. A flat ion saturation region was found in the current-voltage curve of the probe. The ion saturation current to a cylindrical probe in a high-pressure non local thermal equilibrium (LTE) plasma was modeled. Thermal effects and ionization/recombination processes inside the probe perturbed region were taken into account. Averaged radial profiles of the electron and heavy particle temperatures as well as the electron density were obtained. An electron temperature around 11 000 K, a heavy particle temperature around 9500 K and an electron density of about 4 Multiplication-Sign 10{sup 22} m{sup -3}, were found at the jet centre at 3.5 mm downstream from the torch exit. Large deviations from kinetic equilibrium were found throughout the plasma jet. The electron and heavy particle temperature profiles showed good agreement with those reported in the literature by using spectroscopic techniques. It was also found that the temperature radial profile based on LTE was very close to that of the electrons. The calculations have shown that this method is particularly useful for studying spraying-type plasma jets characterized by electron temperatures in the range 9000-14 000 K.

  7. Microplasma jet at atmospheric pressure

    SciTech Connect

    Hong, Yong Cheol; Uhm, Han Sup

    2006-11-27

    A nitrogen microplasma jet operated at atmospheric pressure was developed for treating thermally sensitive materials. For example, the plasma sources in treatment of vulnerable biological materials must operate near the room temperature at the atmospheric pressure, without any risk of arcing or electrical shock. The microplasma jet device operated by an electrical power less than 10 W exhibited a long plasma jet of about 6.5 cm with temperature near 300 K, not causing any harm to human skin. Optical emission measured at the wide range of 280-800 nm indicated various reactive species produced by the plasma jet.

  8. A donut-shape distribution of OH radicals in atmospheric pressure plasma jets

    NASA Astrophysics Data System (ADS)

    Yue, Yuanfu; Wu, Fan; Cheng, He; Xian, Yubin; Liu, Dawei; Lu, Xinpei; Pei, Xuekai

    2017-01-01

    In this work, OH radicals that have a donut-shape distribution in the room-temperature atmospheric-pressure plasma jet are investigated using the laser-induced fluorescence method. The plasma jet driven by a pulse power supply is operated under two conditions: without the ground electrode and with the ground electrode. It is found that the OH radicals distribute as a donut-shape for the first several pulses under both two conditions. With more pulses applied, the donut-shape disappears and OH radicals distribute as a solid disk. Detailed investigations show that the total OH radicals in the plasma plume are formed from two parts. One part is generated by the plasma plume outside the tube with a structure of a donut-shape. The other part is generated by the plasma inside the tube with a structure of a solid disk, which can be transported to the downstream with gas stream and leads to the disappearance of the donut-shape in the plasma plum. Moreover, when the ground electrode is applied, higher intensity of OH is obtained as well as OH donut-shape distribution is observed with dehumidified working gas. It may be due to the higher electron density and its donut-shape distribution in the effluent according to the simulations and experimental results.

  9. [Investigation on the gas temperature of a plasma jet at atmospheric pressure by emission spectrum].

    PubMed

    Li, Xue-chen; Yuan, Ning; Jia, Peng-ying; Niu, Dong-ying

    2010-11-01

    A plasma jet of a dielectric barrier discharge in coaxial electrode was used to produce plasma plume in atmospheric pressure argon. Spatially and temporally resolved measurement was carried out by photomultiplier tubes. The light emission signals both from the dielectric barrier discharge and from the plasma plume were analyzed. Furthermore, emission spectrum from the plasma plume was collected by high-resolution optical spectrometer. The emission spectra of OH (A 2sigma + --> X2 II, 307.7-308.9 nm) and the first negative band of N2+ (B2 sigma u+ --> X2 IIg+, 390-391.6 nm) were used to estimate the rotational temperature of the plasma plume by fitting the experimental spectra to the simulated spectra. The rotational temperature obtained is about 443 K by fitting the emission spectrum from the OH, and that from the first negative band of N2+ is about 450 K. The rotational temperatures obtained by the two method are consistent within 5% error band. The gas temperature of the plasma plume at atmospheric pressure was obtained because rotational temperature equals to gas temperature approximately in gas discharge at atmospheric pressure. Results show that gas temperature increases with increasing the applied voltage.

  10. Influence of voltage magnitude on the dynamic behavior of a stable helium atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Ning, Wenjun; Wang, Lijun; Wu, Chen; Jia, Shenli

    2014-08-01

    Effects of voltage magnitude on the development of a stable helium atmospheric pressure plasma jet are investigated by current measurements and high temporal-resolution streak images. Generated by a coaxial dielectric barrier discharge structure, the entire discharge can be classified into three regions: discharges in the tube gap, downstream jet, and up-streamer. The discharge morphologies of each region are analyzed. In the positive discharge phase, there are two discharges in the tube gap between the electrodes; the first one is ignited as corona and then developed into streamer corona, and the second one is similar with positive glow. The downstream jet is ignited independently from the discharge in the tube gap. Referred as "plasma bullet," the dynamic behavior of the jet can be well described as a positive streamer. Under specific applied voltage, the jet is found to be composed by double bullets in which case the jet length decreases since that less charge is carried by the first bullet. The up-streamer can be captured as long as the discharge in the tube gap is activated. Propagating with velocity of ˜4 km/s, the up-streamer can be regarded as the extension of the first discharge in the tube gap. In the negative discharge phase, the discharge is confined in the tube gap with nearly symmetrical morphology with the positive one. Besides, with the rising of voltage, the negative discharge is initially intensified and then turns weaker after surpassing certain voltage, which may provide suitable condition for the occurrence of double-bullet phenomenon.

  11. Surface conductivity dependent dynamic behaviour of an ultrafine atmospheric pressure plasma jet for microscale surface processing

    NASA Astrophysics Data System (ADS)

    Abuzairi, Tomy; Okada, Mitsuru; Bhattacharjee, Sudeep; Nagatsu, Masaaki

    2016-12-01

    An experimental study on the dynamic behaviour of microcapillary atmospheric pressure plasma jets (APPJs) with 5 μm tip size for surfaces of different conductivity is reported. Electrical and spatio-temporal characteristics of the APPJs are monitored using high voltage probe, current monitor and high speed intensified charge couple device camera. From these experimental results, we presented a simple model to understand the electrical discharge characteristics of the capillary APPJs with double electrodes, and estimated the velocity of the ionization fronts in the jet and the electron density to be 3.5-4.2 km/s and 2-7 × 1017 m-3. By analyzing the dynamics of the microcapillary APPJs for different substrate materials, it was found that the surface irradiation area strongly depended on the substrate conductivity and permittivity, especially in the case of polymer-like substrate, surface irradiation area was significantly broadened probably due to the repelling behaviour of the plasma jets from the accumulated electrical charges on the polymer surface. The effect of applying a substrate bias in the range from -900 V to +900 V on the plasma irradiation onto the substrates was also investigated. From the knowledge of the present results, it is helpful for choosing the substrate materials for microscale surface modification.

  12. Discharge modes of a DC operated atmospheric pressure air plasma jet

    NASA Astrophysics Data System (ADS)

    Kolb, Juergen; Pei, Xuekai; Kredl, Jana; Lu, Xinpei

    2016-09-01

    By flowing air or nitrogen through a microhollow cathode discharge geometry an afterglow plasma jet can be generated at atmospheric pressure in air. The plasma jet has been successfully used for the inactivation of bacteria and yeast. The responsible reaction chemistry is based on the production of high concentrations of nitric oxide. Production yields depend in particular on gas flow rate and energy dissipated in the plasma. The same parameters also determine different modes of operation for the jet. A true DC operation is achieved for low to moderate gas flow rate of about 1 slm and discharge currents on the order of 10 mA. When increasing the gas flow rate to 10 slm the operation is changing to a self-pulsing mode with characteristics similar to the ones observed for a transient spark. By increasing the current a DC operation can be achieved again also at higher gas flow rates. The parameter regimes for different modes of operation can be described by the reduced electric field E/N.

  13. Experimental investigation of supersonic low pressure air plasma flows obtained with different arc-jet operating conditions

    SciTech Connect

    Lago, Viviana; Ndiaye, Abdoul-Aziz

    2012-11-27

    A stationary arc-jet plasma flow at low pressure is used to simulate some properties of the gas flow surrounding a vehicle during its entry into celestial body's atmospheres. This paper presents an experimental study concerning plasmas simulating a re-entry into our planet. Optical measurements have been carried out for several operating plasma conditions in the free stream, and in the shock layer formed in front of a flat cylindrical plate, placed in the plasma jet. The analysis of the spectral radiation enabled the identification of the emitting species, the determination of the rotational and vibrational temperatures in the free-stream and in the shock layer and the determination of the distance of the shock to the flat plate face. Some plasma fluid parameters like, stagnation pressure, specific enthalpy and heat flux have been determined experimentally along the plasma-jet axis.

  14. Influence of Penning effect on the plasma features in a non-equilibrium atmospheric pressure plasma jet

    SciTech Connect

    Chang, Zhengshi; Zhang, Guanjun; Jiang, Nan; Cao, Zexian

    2014-03-14

    Non-equilibrium atmospheric pressure plasma jet (APPJ) is a cold plasma source that promises various innovative applications. The influence of Penning effect on the formation, propagation, and other physical properties of the plasma bullets in APPJ remains a debatable topic. By using a 10 cm wide active electrode and a frequency of applied voltage down to 0.5 Hz, the Penning effect caused by preceding discharges can be excluded. It was found that the Penning effect originating in a preceding discharge helps build a conductive channel in the gas flow and provide seed electrons, thus the discharge can be maintained at a low voltage which in turn leads to a smaller propagation speed for the plasma bullet. Photographs from an intensified charge coupled device reveal that the annular structure of the plasma plume for He is irrelevant to the Penning ionization process arising from preceding discharges. By adding NH{sub 3} into Ar to introduce Penning effect, the originally filamentous discharge of Ar can display a rather extensive plasma plume in ambient as He. These results are helpful for the understanding of the behaviors of non-equilibrium APPJs generated under distinct conditions and for the design of plasma jet features, especially the spatial distribution and propagation speed, which are essential for application.

  15. Effects of a Nonthermal Atmospheric Pressure Plasma Jet on Human Gingival Fibroblasts for Biomedical Application

    PubMed Central

    2016-01-01

    Nonthermal atmospheric pressure plasma jets (APPJ) have been developed and applied in biomedical research as a cancer treatment or bacterial sterilization. However, the drawback of APPJ on normal oral cells during plasma treatment and underlying cell death mechanisms have not been studied and clearly explained, although there is known to be an influence from reactive oxygen species (ROS). Hence, this study investigates whether and how a nonthermal atmospheric pressure air plasma jet kills human normal gingival cells using immortalized human gingival fibroblasts (hTERT-hNOF cells). In this study, a set of physicochemical or biological methods were used to illuminate the killing mechanisms. It was found that ROS were induced intracellularly without a breakdown of the cell wall and apoptosis was involved in cell death when an air APPJ treatment was performed on the cells directly without media; the air treatment only supported a detachment of the cells without increase of ROS. It was also revealed that a correlation between intracellular ROS concentration and cells viability existed. These results indicated that the direct air APPJ treatment possibly raises safety issue to normal tissue and thereby APPJ application in biomedical field needs more in vitro and in vivo study to optimize it. PMID:27597959

  16. Effects of a Nonthermal Atmospheric Pressure Plasma Jet on Human Gingival Fibroblasts for Biomedical Application.

    PubMed

    Lee, Jung-Hwan; Kim, Kyoung-Nam

    2016-01-01

    Nonthermal atmospheric pressure plasma jets (APPJ) have been developed and applied in biomedical research as a cancer treatment or bacterial sterilization. However, the drawback of APPJ on normal oral cells during plasma treatment and underlying cell death mechanisms have not been studied and clearly explained, although there is known to be an influence from reactive oxygen species (ROS). Hence, this study investigates whether and how a nonthermal atmospheric pressure air plasma jet kills human normal gingival cells using immortalized human gingival fibroblasts (hTERT-hNOF cells). In this study, a set of physicochemical or biological methods were used to illuminate the killing mechanisms. It was found that ROS were induced intracellularly without a breakdown of the cell wall and apoptosis was involved in cell death when an air APPJ treatment was performed on the cells directly without media; the air treatment only supported a detachment of the cells without increase of ROS. It was also revealed that a correlation between intracellular ROS concentration and cells viability existed. These results indicated that the direct air APPJ treatment possibly raises safety issue to normal tissue and thereby APPJ application in biomedical field needs more in vitro and in vivo study to optimize it.

  17. Design and characterization of an RF excited micro atmospheric pressure plasma jet for reference in plasma medicine

    NASA Astrophysics Data System (ADS)

    Schulz-von der Gathen, Volker

    2015-09-01

    Over the last decade a huge variety of atmospheric pressure plasma jets has been developed and applied for plasma medicine. The efficiency of these non-equilibrium plasmas for biological application is based on the generated amounts of reactive species and radiation. The gas temperatures stay within a range tolerable for temperature-sensitive tissues. The variety of different discharge geometries complicates a direct comparison. In addition, in plasma-medicine the combination of plasma with reactive components, ambient air, as well as biologic tissue - typically also incorporating fluids - results in a complex system. Thus, real progress in plasma-medicine requires a profound knowledge of species, their fluxes and processes hitting biological tissues. That will allow in particular the necessary tailoring of the discharge to fit the conditions. The complexity of the problem can only be overcome by a common effort of many groups and requires a comparison of their results. A reference device based on the already well-investigated micro-scaled atmospheric pressure plasma jet is presented. It is developed in the frame of the European COST initiative MP1101 to establish a publicly available, stable and reproducible source, where required plasma conditions can be investigated. Here we present the design and the ideas behind. The presentation discusses the requirements for the reference source and operation conditions. Biological references are also defined by the initiative. A specific part of the talk will be attributed to the reproducibility of results from various samples of the device. Funding by the DFG within the Package Project PAK816 ``Plasma Cell Interaction in Dermatology'' and the Research Unit FOR 1123 ``Physics of microplasmas'' is gratefully acknowledged.

  18. [Investigation on the electron density of a micro-plasma jet operated at atmospheric pressure].

    PubMed

    Li, Xue-chen; Zhao, Na; Liu, Wei-yuan; Liu, Zhi-qiang

    2010-07-01

    In the present paper, a micro-hollow cathode discharge setup was used to generate micro-plasma jet in flowing mixture of Ar and N2 at atmospheric pressure. The characteristics of the micro-plasma jet were investigated by means of optical method and electrical one. It has been found that breakdown occurs in the gas between the two electrodes when the input power of electric source is increased to a certain value. Plasma appears along the gas flow direction when the mixed gas flows from the aperture of the micro-hollow cathode, and the length of plasma reaches 4 mm. The discharge current is quasi-continuous, and the duration of discharge pulse is about 0.1 micros. Electron density was studied by using Einstein equation and Stark broadening of spectral lines from the emission spectrum respectively. It was found that the results of electron density calculated by the two methods are consistent with the order of 10(15) x cm(-3). It was also found that the electron density is almost independent of power. A qualitative explanation to the phenomenon is given based on the gas discharge theory.

  19. Electron properties of the plume of an atmospheric pressure helium plasma jet

    NASA Astrophysics Data System (ADS)

    Adress, Wameedh; Nedanovska, Elena; Nersisyan, Gagik; Riley, David; Graham, William

    2013-09-01

    Atmospheric pressure plasma, APP, jets, are now attracting great interest because of their potential uses in many applications; for example surface modification and plasma medicine. These applications require an insight into their plasma chemistry, which is strongly influenced by the electron energy distribution function. Here we report the use of Thomson scattering to measure the electron properties in the plume created by a 20 kHz, 2mm diameter helium APP jet operating into the open air. A 532 nm Nd:YAG laser beam is focussed into the plasma plume. The temporally and spatially resolved spectra of light at 90° to the laser direction is detected. The spectra contain light from Thomson Scattering from electrons, along with Rayleigh and Raman scattering from atoms and molecules. These components are resolved in a manner similar to that described in ref 1. Our measurements reveal a ``ring-like'' radial distribution of both the electron density and temperature, with outer values of ~ 7×1013 cm-3 and 0.4 eV and inner values of ~ 2×1013 cm-3 and 0.1 eV respectively at 4 mm from the end of the quartz tube.

  20. PECVD of nanostructured SiO2 in a modulated microwave plasma jet at atmospheric pressure

    NASA Astrophysics Data System (ADS)

    Hnilica, J.; Schäfer, J.; Foest, R.; Zajíčková, L.; Kudrle, V.

    2013-08-01

    Atmospheric pressure plasma enhanced chemical vapour deposition (AP-PECVD) of thin films by means of a microwave plasma jet operating with mixtures of argon and tetrakis(trimethylsilyloxy)silane (TTMS) is reported for the first time. In contrast to other siloxy-alkanes that are commonly used for PECVD, the molecule of TTMS (C12H36O4Si5) exhibits a complex and symmetric molecular structure which is presumably essential for a large scale nanostructuring of the films. Deposited films have been characterized by means of electron microscopy (SEM), x-ray spectroscopy (EDX), and infra-red spectroscopy (FTIR). The applied methods demonstrate the prevalent inorganic SiO2-like character of the films and their highly fractalized nanostructure over a wide range of dimension 100-104 nm. Contact angle measurements show the superhydrophobicity of the films, while the dispersive component of the surface energy can be varied in a controlled way by low-frequency amplitude modulation of the excitation power of the MW discharge. The modulation regimes of the jet have been investigated by means of time-resolved optical emission spectroscopy in order to describe the oscillations of plasma parameters e.g. rotational temperature from OH and relative emission of silicon atoms to substantiate the reproducibility of the deposition conditions and to correlate the plasma properties with the resulting film properties.

  1. Two-dimensional profile measurement of plasma parameters in radio frequency-driven argon atmospheric pressure plasma jet

    SciTech Connect

    Seo, B. H.; Kim, J. H.; Kim, D. W.; You, S. J.

    2015-09-15

    The two-dimensional profiles of the electron density, electron temperature, neutral translational temperature, and molecular rotational temperature are investigated in an argon atmospheric pressure plasma jet, which is driven by the radio frequency of 13.56 MHz by means of the laser scattering methods of Thomson, Rayleigh, and Raman. All measured parameters have maximum values at the center of the discharge and decrease toward the plasma edge. The results for the electron temperature profile are contrary to the results for the microwave-driven plasma. From our experimental results, the profiles of the plasma parameters arise from the radial contraction of plasmas and the time averaged profile of the electric field, which is obtained by a microwave simulation performed under identical conditions to the plasma jet. In the case of the neutral temperature, a higher translational temperature than the rotational temperature is measured, and its discrepancy is tentatively explained in terms of the low ion-neutral charge exchange rate and the additional degrees of freedom of the molecules. The description of our experimental results and the underlying physics are addressed in detail.

  2. Effect of atmospheric pressure plasma jet on the foodborne pathogens attached to commercial food containers.

    PubMed

    Kim, Hyun-Joo; Jayasena, Dinesh D; Yong, Hae In; Alahakoon, Amali U; Park, Sanghoo; Park, Jooyoung; Choe, Wonho; Jo, Cheorun

    2015-12-01

    Bacterial biofilms are associated with numerous infections and problems in the health care and food industries. The aim of this study was to evaluate the bactericidal effect of an atmospheric pressure plasma (APP) jet on Escherichia coli O157:H7, Listeria monocytogenes, and Salmonella Typhimurium biofilm formation on collagen casing (CC), polypropylene (PP) and polyethylene terephthalate (PET), which are widely used food container materials. The samples were treated separately with the APP jet at a 50-W input power for 5 and 10 min, and nitrogen (6 l per minute) gas combined with oxygen (10 standard cubic centimeters per minute) was used to produce the APP. The APP jet reduced the number of bacterial cells in a time-dependent manner. All pathogens attached to CC, PP, and PET were reduced by 3-4 log CFU/cm(2) by the 10-min APP treatment. The developed APP jet was effectively reduced biofilms on CC, PP, and PET.

  3. Atmospheric pressure plasma jets beyond ground electrode as charge overflow in a dielectric barrier discharge setup

    SciTech Connect

    Jiang Nan; Ji Ailing; Cao Zexian

    2010-08-15

    With a proper combination of applied voltage and the width of ground electrode, atmospheric pressure plasma jets extending beyond the ground electrode, whether it sits on the downstream or the upstream side, can be equally obtained with a dielectric barrier discharge setup, which can be ascribed to the overflow of deposited charges [J. Appl. Phys. 106, 013308 (2009)]. Here, we show that, by using narrower ground electrodes, such an overflow jet can be successfully launched at a much reduced voltage (down to below 10 kV). Moreover, by using transparent and triadic ground electrodes, development of charge overflow beneath the ground electrode was temporally and spatially resolved. Temporal evolution of discharge currents measured on the severed ground electrode helps establish the propagation dynamics of discharges along the dielectric surface beneath ground electrode, and also reinforces the conception that the streamer's head is in connection to the active electrode via a conducting channel. A small propagation velocity of 3.3x10{sup 3} m/s was measured for the ''overflow'' jet inside the dielectric tube. The availability of such overflow jets is enormously advantageous concerning their application to living bodies, to which the high voltage at active electrode is lethally dangerous.

  4. Atmospheric pressure plasma jets beyond ground electrode as charge overflow in a dielectric barrier discharge setup

    NASA Astrophysics Data System (ADS)

    Jiang, Nan; Ji, Ailing; Cao, Zexian

    2010-08-01

    With a proper combination of applied voltage and the width of ground electrode, atmospheric pressure plasma jets extending beyond the ground electrode, whether it sits on the downstream or the upstream side, can be equally obtained with a dielectric barrier discharge setup, which can be ascribed to the overflow of deposited charges [J. Appl. Phys. 106, 013308 (2009)]. Here, we show that, by using narrower ground electrodes, such an overflow jet can be successfully launched at a much reduced voltage (down to below 10 kV). Moreover, by using transparent and triadic ground electrodes, development of charge overflow beneath the ground electrode was temporally and spatially resolved. Temporal evolution of discharge currents measured on the severed ground electrode helps establish the propagation dynamics of discharges along the dielectric surface beneath ground electrode, and also reinforces the conception that the streamer's head is in connection to the active electrode via a conducting channel. A small propagation velocity of 3.3×103 m/s was measured for the "overflow" jet inside the dielectric tube. The availability of such overflow jets is enormously advantageous concerning their application to living bodies, to which the high voltage at active electrode is lethally dangerous.

  5. Effect of O2 additive on spatial uniformity of atmospheric-pressure helium plasma jet array driven by microsecond-duration pulses

    NASA Astrophysics Data System (ADS)

    Zhang, Cheng; Shao, Tao; Zhou, Yixiao; Fang, Zhi; Yan, Ping; Yang, Wenjin

    2014-07-01

    Plasma jet array is a promising device for producing low-temperature plasma at atmospheric pressure. In our letter, the effect of O2 additive on spatial uniformity of one-dimensional helium plasma jet array is described. The length of the plasma jet in the middle of the array before the injection of O2 additive is less than that on the edges of the array. However, when a small amount of O2 additive is injected into the plasma jet array, the length increases and becomes approximately the same as the length of the plasma jets on the edges of the array. The improvement of spatial uniformity of the plasma jet array is due to the enhancement of the Penning ionization in the plasma jets caused by O2 additive. Too much quantity of O2 additive, however, may lead to discharge quenching in the plasma jet array.

  6. On the design and characterization of a new cold atmospheric pressure plasma jet and its applications on cancer cells treatment.

    PubMed

    Akhlaghi, Morteza; Rajayi, Hajar; Mashayekh, Amir Shahriar; Khani, Mohammadreza; Hassan, Zuhair Mohammad; Shokri, Babak

    2015-06-23

    In this paper, a new configuration of a cold atmospheric pressure plasma jet has been designed and constructed. Poly-methyl-methacrylate was used as a new dielectric in this configuration which in comparison to other dielectrics is inexpensive, more resistant against break, and also more shapeable. Then, the plasma jet parameters such as plume temperature, rotational and vibrational temperatures, power, electrical behavior (voltage and current profile), electron density, and the produced reactive species were characterized. In order to determine the jet temperature and the amount of reactive species, effects of applied voltage, gas flow rate, and distance from the nozzle were studied. The power of the jet was specified using Lissajous curve approach. The plume temperature of the plasma jet was about the room temperature. Optical emission spectroscopy determined the type of reactive species, and also electron density and its corresponding plasma frequency (~6.4 × 10(13) cm(-3) and 4.52 × 10(11) Hz). Because of producing different reactive species, the device can be used in different applications, especially in plasma medicine. Thus, 4T1 cancer cells were treated using this plasma jet. The results showed that this plasma jet has a great potential to kill one of the most aggressive and resistant cancerous cell lines.

  7. Decontamination of chemical and biological warfare (CBW) agents using an atmospheric pressure plasma jet (APPJ)

    NASA Astrophysics Data System (ADS)

    Herrmann, H. W.; Henins, I.; Park, J.; Selwyn, G. S.

    1999-05-01

    The atmospheric pressure plasma jet (APPJ) [A. Schütze et al., IEEE Trans. Plasma Sci. 26, 1685 (1998)] is a nonthermal, high pressure, uniform glow plasma discharge that produces a high velocity effluent stream of highly reactive chemical species. The discharge operates on a feedstock gas (e.g., He/O2/H2O), which flows between an outer, grounded, cylindrical electrode and an inner, coaxial electrode powered at 13.56 MHz rf. While passing through the plasma, the feedgas becomes excited, dissociated or ionized by electron impact. Once the gas exits the discharge volume, ions and electrons are rapidly lost by recombination, but the fast-flowing effluent still contains neutral metastable species (e.g., O2*, He*) and radicals (e.g., O, OH). This reactive effluent has been shown to be an effective neutralizer of surrogates for anthrax spores and mustard blister agent. Unlike conventional wet decontamination methods, the plasma effluent does not cause corrosion and it does not destroy wiring, electronics, or most plastics, making it highly suitable for decontamination of sensitive equipment and interior spaces. Furthermore, the reactive species in the effluent rapidly degrade into harmless products leaving no lingering residue or harmful by-products.

  8. Decontamination of chemical and biological warfare (CBW) agents using an atmospheric pressure plasma jet (APPJ)

    SciTech Connect

    Herrmann, H.W.; Henins, I.; Park, J.; Selwyn, G.S.

    1999-05-01

    The atmospheric pressure plasma jet (APPJ) [A. Sch{umlt u}tze {ital et al.}, IEEE Trans. Plasma Sci. {bold 26}, 1685 (1998)] is a nonthermal, high pressure, uniform glow plasma discharge that produces a high velocity effluent stream of highly reactive chemical species. The discharge operates on a feedstock gas (e.g., He/O{sub 2}/H{sub 2}O), which flows between an outer, grounded, cylindrical electrode and an inner, coaxial electrode powered at 13.56 MHz rf. While passing through the plasma, the feedgas becomes excited, dissociated or ionized by electron impact. Once the gas exits the discharge volume, ions and electrons are rapidly lost by recombination, but the fast-flowing effluent still contains neutral metastable species (e.g., O{sub 2}{sup {asterisk}}, He{sup {asterisk}}) and radicals (e.g., O, OH). This reactive effluent has been shown to be an effective neutralizer of surrogates for anthrax spores and mustard blister agent. Unlike conventional wet decontamination methods, the plasma effluent does not cause corrosion and it does not destroy wiring, electronics, or most plastics, making it highly suitable for decontamination of sensitive equipment and interior spaces. Furthermore, the reactive species in the effluent rapidly degrade into harmless products leaving no lingering residue or harmful by-products. {copyright} {ital 1999 American Institute of Physics.}

  9. Effects of the nozzle design on the properties of plasma jet and formation of YSZ coatings under low pressure conditions

    NASA Astrophysics Data System (ADS)

    Sun, Chengqi; Gao, Yang; Yang, Deming; Fu, Yingqing

    2016-09-01

    How to control the quality of the coatings has become a major problem during the plasma spraying. Because nozzle contour has a great influence on the characteristic of the plasma jet, two kinds of plasma torches equipped with a standard cylindrical nozzle and a converging-diverging nozzle are designed for low pressure plasma spraying(LPPS) and very low pressure plasma spraying(VLPPS). Yttria stabilized zirconia(YSZ) coatings are obtained in the reducing pressure environment. The properties of the plasma jet without or with powder injection are analyzed by optical emission spectroscopy, and the electron temperature is calculated based on the ratio of the relative intensity of two Ar I spectral lines. The results show that some of the YSZ powder can be vaporized in the low pressure enlarged plasma jet, and the long anode nozzle may improve the characteristics of the plasma jet. The coatings deposited by LPPS are mainly composed of the equiaxed grains and while the unmelted powder particles and large scalar pores appear in the coatings made by VLPPS. The long anode nozzle could improve the melting of the powders and deposition efficiency, and enhance the coatings' hardness. At the same time, the long anode nozzle could lead to a decrease in the overspray phenomenon. Through the comparison of the two different size's nozzle, the long anode is much more suitable for making the YSZ coatings.

  10. Measurement of plasma-generated RONS in the cancer cells exposed by atmospheric pressure helium plasma jet

    NASA Astrophysics Data System (ADS)

    Joh, Hea Min; Baek, Eun Jeong; Kim, Sun Ja; Chung, Tae Hun

    2015-09-01

    The plasma-induced reactive oxygen and nitrogen species (RONS) could result in cellular responses including DNA damages and apoptotic cell death. These chemical species, O, O2-,OH, NO, and NO2-,exhibit strong oxidative stress and/or trigger signaling pathways in biological cells. Each plasma-generated chemical species having biological implication should be identified and quantitatively measured. For quantitative measurement of RONS, this study is divided into three stages; plasma diagnostics, plasma-liquid interactions, plasma-liquid-cell interactions. First, the optical characteristics of the discharges were obtained by optical emission spectroscopy to identify various excited plasma species. And the characteristics of voltage-current waveforms, gas temperature, and plume length with varying control parameters were measured. Next, atmospheric pressure plasma jet was applied on the liquid. The estimated OH radical densities were obtained by ultraviolet absorption spectroscopy at the liquid surface. And NO2-is detected by Griess test and compared between the pure liquid and the cell-containing liquid. Finally, bio-assays were performed on plasma treated human lung cancer cells (A549). Intracellular ROS production was measured using DCF-DA. Among these RONS, productions of NO and OH within cells were measured by DAF-2DA and APF, respectively. The data are very suggestive that there is a strong correlation among the production of RONS in the plasmas, liquids, and cells.

  11. Functionalization of graphene by atmospheric pressure plasma jet in air or H2O2 environments

    NASA Astrophysics Data System (ADS)

    Huang, Weixin; Ptasinska, Sylwia

    2016-03-01

    The functionalization of graphene, which deforms its band structure, can result in a metal-semiconductor transition. In this work, we report a facile strategy to oxidize single-layer graphene using an atmospheric pressure plasma jet (APPJ) that generates a variety of reactive plasma species at close to ambient temperature. We systematically characterized the oxygen content and chemical structure of the graphene films after plasma treatment under different oxidative conditions (ambient air atmosphere or hydrogen peroxide solution) by X-ray Photoelectron Spectroscopy (XPS). Plasma-treated graphene films containing more than 40% oxygen were obtained in both oxidative environments. Interestingly, prolonged irradiation led to the reduction of graphene oxides. N-doping of graphene also occurred during the APPJ treatment in H2O2 solution; the nitrogen content of the doped graphene was dependent on the duration of irradiation and reached up to 8.1% within 40 min. Moreover, the H2O2 solution served as a buffer layer that prevented damage to the graphene during plasma irradiation. Four-point probe measurement revealed an increase in sheet resistance of the plasma-treated graphene, indicating the transition of the material property from semi-metallic to semiconducting.

  12. OH density optimization in atmospheric-pressure plasma jet by using multiple ring electrodes

    NASA Astrophysics Data System (ADS)

    Yue, Y.; Pei, X.; Lu, X.

    2016-01-01

    OH radical is one of the important reactive species generated by non-equilibrium atmospheric-pressure plasma jets, which is believed to play an important role in plasma medicine applications such as cancer therapy, wound healing and sterilization. In this study, a method to increase OH density is proposed. By using multiple pairs of ring electrodes, we generate 3-5 times more OH radicals than in the common device which uses only one high-voltage ring electrode. Discharge imaging shows that the plasma plume with only one ring electrode is longer and its emission intensity is higher than those with multiple pairs of ring electrodes. Further studies indicate that the distribution of OH radicals is significantly influenced by the gas flow rate. At higher gas flow rates, the OH peak concentration is detected further away from the nozzle, and the position of the peak OH concentration correlates with the product of the gas flow velocity and the pulse duration. As observed from the emission spectra, multiple electrodes only enhance the plasma inside the tube rather than the plasma plume in the surrounding air. These results suggest that the OH radicals are mainly generated inside the tube and then delivered to the outer plasma plume region by the gas flow.

  13. Effect of sheath gas in atmospheric-pressure plasma jet for potato sprouting suppression

    NASA Astrophysics Data System (ADS)

    Nishiyama, S.; Monma, M.; Sasaki, K.

    2016-09-01

    Recently, low-temperature atmospheric-pressure plasma jets (APPJs) attract much interest for medical and agricultural applications. We try to apply APPJs for the suppression of potato sprouting in the long-term storage. In this study, we investigated the effect of sheath gas in APPJ on the suppression efficiency of the potato sprouting. Our APPJ was composed of an insulated thin wire electrode, a glass tube, a grounded electrode which was wound on the glass tube, and a sheath gas nozzle which was attached at the end of the glass tube. The wire electrode was connected to a rectangular-waveform power supply at a frequency of 3 kHz and a voltage of +/- 7 kV. Helium was fed through the glass tube, while we tested dry nitrogen, humid nitrogen, and oxygen as the sheath gas. Eyes of potatoes were irradiated by APPJ for 60 seconds. The sprouting probability was evaluated at two weeks after the plasma irradiation. The sprouting probability was 28% when we employed no sheath gases, whereas an improved probability of 10% was obtained when we applied dry nitrogen as the sheath gas. Optical emission spectroscopy was carried out to diagnose the plasma jet. It was suggested that reactive species originated from nitrogen worked for the efficient suppression of the potato sprouting.

  14. Synthesis of highly transparent ultrananocrystalline diamond films from a low-pressure, low-temperature focused microwave plasma jet.

    PubMed

    Liao, Wen-Hsiang; Wei, Da-Hua; Lin, Chii-Ruey

    2012-01-19

    This paper describes a new low-temperature process underlying the synthesis of highly transparent ultrananocrystalline diamond [UNCD] films by low-pressure and unheated microwave plasma jet-enhanced chemical vapor deposition with Ar-1%CH4-10%H2 gas chemistry. The unique low-pressure/low-temperature [LPLT] plasma jet-enhanced growth even with added H2 and unheated substrates yields UNCD films similar to those prepared by plasma-enhanced growth without addition of H2 and heating procedure. This is due to the focused plasma jet which effectively compensated for the sluggish kinetics associated with LPLT growth. The effects of pressure on UNCD film synthesis from the microwave plasma jet were systematically investigated. The results indicated that the substrate temperature, grain size, surface roughness, and sp3 carbon content in the films decreased with decreasing pressure. The reason is due to the great reduction of Hα emission to lower the etching of sp2 carbon phase, resulting from the increase of mean free path with decreasing pressure. We have demonstrated that the transition from nanocrystalline (80 nm) to ultrananocrystalline (3 to 5 nm) diamond films grown via microwave Ar-1%CH4-10%H2 plasma jets could be controlled by changing the pressure from 100 to 30 Torr. The 250-nm-thick UNCD film was synthesized on glass substrates (glass transition temperature [Tg] 557°C) using the unique LPLT (30 Torr/460°C) microwave plasma jet, which produced UNCD films with a high sp3 carbon content (95.65%) and offered high optical transmittance (approximately 86% at 700 nm).

  15. Atmospheric-Pressure Non-thermal Plasma-JET effects on PS and PE surfaces

    NASA Astrophysics Data System (ADS)

    Arrieta, J.; Asenjo, J.; Vargas, I.; Solis, Y.

    2015-03-01

    The Atmospheric-Pressure Non-Thermal Plasma (APNTP) has become a topic of a great interest for a wide spectrum of applications in different industry branches, including the surface of treatment processes. In this work we evaluate the effect of an argon APNTP exposure to determine changes suffered by a polystyrene (PS) and polyethylene (PE) polymer surface through RAMAN spectroscopy and SEM. It was determined that the hydrophilic change in energetic terms, i.e. surface activation in the PS and PE polymers is addition of oxygen by surface activation when the samples with jet plasma are exposed with the inert argon gas. It was possible to characterize the hydrophilic shift based on the change in intensity of the spectra.

  16. Investigations of the surface activation of thermoplastic polymers by atmospheric pressure plasma treatment with a stationary plasma jet

    NASA Astrophysics Data System (ADS)

    Moritzer, Elmar; Nordmeyer, Timo; Leister, Christian; Schmidt, Martin Andreas; Grishin, Artur; Knospe, Alexander

    2016-03-01

    The production of high-quality thermoplastic parts often requires an additional process step after the injection molding stage. This may be a coating, bonding process or a 2K-injection moulding process. A commonly used process to improve the bond strength is atmospheric pressure plasma treatment. A variety of applications are realized with the aid of CNC systems. Although they ensure excellent reproducibility, they make it difficult to implement inline applications. This paper therefore examines the possibility of surface treatment using a stationary plasma jet. However, before it is possible to integrate this technology into a production process, preliminary trials need to be carried out to establish which factors influence the process. Experimental tests were performed using a special test set-up, enabling geometric, plasma-specific parameters to be identified. These results can help with the practical integration of this technology into existing production processes.

  17. DNA damage in oral cancer and normal cells induced by nitrogen atmospheric pressure plasma jets

    NASA Astrophysics Data System (ADS)

    Han, Xu; Kapaldo, James; Liu, Yueying; Stack, M. Sharon; Ptasinska, Sylwia

    2015-09-01

    Nitrogen atmospheric pressure plasma jets (APPJs) have been shown to effectively induce DNA double strand breaks in SCC25 oral cancer cells. The APPJ source constructed in our laboratory operates based on dielectric barrier discharge. It consists of two copper electrodes alternatively wrapping around a fused silica tube with nitrogen as a feed gas. It is generally more challenging to ignite plasma in N2 atmosphere than in noble gases. However, N2 provides additional advantages such as lower costs compared to noble gases, thus this design can be beneficial for the future long-term clinical use. To compare the effects of plasma on cancer cells (SCC25) and normal cells (OKF), the cells from both types were treated at the same experimental condition for various treatment times. The effective area with different damage levels after the treatment was visualized as 3D maps. The delayed damage effects were also explored by varying the incubation times after the treatment. All of these studies are critical for a better understanding of the damage responses of cellular systems exposed to the plasma radiation, thus are useful for the development of the advanced plasma cancer therapy. The research described herein was supported by the Division of Chemical Sciences, Geosciences and Biosciences, Basic Energy Sciences, Office of Science, United States Department of Energy through Grant No. DE-FC02-04ER15533.

  18. Nonequilibrium atmospheric pressure plasma jet using a combination of 50 kHz/2 MHz dual-frequency power sources

    SciTech Connect

    Zhou, Yong-Jie; Yuan, Qiang-Hua; Li, Fei; Wang, Xiao-Min; Yin, Gui-Qin; Dong, Chen-Zhong

    2013-11-15

    An atmospheric pressure plasma jet is generated by dual sinusoidal wave (50 kHz and 2 MHz). The dual-frequency plasma jet exhibits the advantages of both low frequency and radio frequency plasmas, namely, the long plasma plume and the high electron density. The radio frequency ignition voltage can be reduced significantly by using dual-frequency excitation compared to the conventional radio frequency without the aid of the low frequency excitation source. A larger operating range of α mode discharge can be obtained using dual-frequency excitation which is important to obtain homogeneous and low-temperature plasma. A larger controllable range of the gas temperature of atmospheric pressure plasma could also be obtained using dual-frequency excitation.

  19. Treatment of Candida albicans biofilms with low-temperature plasma induced by dielectric barrier discharge and atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Koban, Ina; Matthes, Rutger; Hübner, Nils-Olaf; Welk, Alexander; Meisel, Peter; Holtfreter, Birte; Sietmann, Rabea; Kindel, Eckhard; Weltmann, Klaus-Dieter; Kramer, Axel; Kocher, Thomas

    2010-07-01

    Because of some disadvantages of chemical disinfection in dental practice (especially denture cleaning), we investigated the effects of physical methods on Candida albicans biofilms. For this purpose, the antifungal efficacy of three different low-temperature plasma devices (an atmospheric pressure plasma jet and two different dielectric barrier discharges (DBDs)) on Candida albicans biofilms grown on titanium discs in vitro was investigated. As positive treatment controls, we used 0.1% chlorhexidine digluconate (CHX) and 0.6% sodium hypochlorite (NaOCl). The corresponding gas streams without plasma ignition served as negative treatment controls. The efficacy of the plasma treatment was determined evaluating the number of colony-forming units (CFU) recovered from titanium discs. The plasma treatment reduced the CFU significantly compared to chemical disinfectants. While 10 min CHX or NaOCl exposure led to a CFU log10 reduction factor of 1.5, the log10 reduction factor of DBD plasma was up to 5. In conclusion, the use of low-temperature plasma is a promising physical alternative to chemical antiseptics for dental practice.

  20. The interaction of an atmospheric pressure plasma jet using argon or argon plus hydrogen peroxide vapour addition with bacillus subtilis

    NASA Astrophysics Data System (ADS)

    Deng, San-Xi; Cheng, Cheng; Ni, Guo-Hua; Meng, Yue-Dong; Chen, Hua

    2010-10-01

    This paper reports that an atmospheric pressure dielectric barrier discharge plasma jet, which uses argon or argon + hydrogen peroxide vapour as the working gas, is designed to sterilize the bacillus subtilis. Compared with the pure argon plasma, the bacterial inactivation efficacy has a significant improvement when hydrogen peroxide vapour is added into the plasma jet. In order to determine which factors play the main role in inactivation, several methods are used, such as determination of optical emission spectra, high temperature dry air treatment, protein leakage quantification, and scanning electron microscope. These results indicate that the possible inactivation mechanisms are the synergistic actions of chemically active species and charged species.

  1. Experimental investigation of photoresist etching by kHz AC atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Wang, Lijun; Zheng, Yashuang; Wu, Chen; Jia, Shenli

    2016-11-01

    In this study, the mechanism of the photoresist (PR) etching by means of a kHz AC atmospheric pressure plasma jet (APPJ) is investigated. The scanning electron (SEM) and the polarizing microscope are used to perform the surface analysis, and the mechanical profilometry is applied to diagnose the etch rate. The results show that granulated structure with numerous microparticles appears at the substrate surface after APPJ treatment, and the etch rate in the etch center is the fastest and gradually slows down to the edge of etch region. In addition, the pin-ring electrode APPJ has the highest etch rate at but easy to damage the Si wafer, the double-ring APPJ is the most stable but requires long time to achieve the ideal etch result, and the etch rate and the etch result of the multi-electrode APPJ fall in between. Ar APPJ had much higher PR etch rate and more irregular etch trace than He APPJ. It is speculated that Ar APPJ is more energetic and effective in transferring reactive species to the PR surface. It is also observed that the effective etch area initially increases and then decreases as plasma jet outlet to the PR surface distance increases.

  2. Nonequilibrium Atmospheric Pressure Ar/O2 Plasma Jet: Properties and Application to Surface Cleaning

    NASA Astrophysics Data System (ADS)

    Jin, Ying; Ren, Chunsheng; Yang, Liang; Zhang, Jialiang

    2016-02-01

    In this study an atmospheric pressure Ar/O2 plasma jet is generated to study the effects of applied voltage and gas flux rate to the behavior of discharge and the metal surface cleaning. The increase in applied voltage leads to increases of the root mean square (rms) current, the input power and the gas temperature. Furthermore, the optical emission spectra show that the emission intensities of metastable argon and atomic oxygen increase with increasing applied voltage. However, the increase in gas flux rate leads to a reduction of the rms current, the input power and the gas temperature. Furthermore, the emission intensities of metastable argon and atomic oxygen decrease when gas flux rate increases. Contact angles are measured to estimate the cleaning performance, and the results show that the increase of applied voltage can improve the cleaning performance. Nevertheless, the increase of gas flux rate cannot improve the cleaning performance. Contact angles are compared for different input powers and gas flux rates to search for a better understanding of the major mechanism for surface cleaning by plasma jets. supported by National Natural Science Foundation of China (No. 11305017)

  3. Decontamination of Chemical/Biological Warfare (CBW) Agents Using an Atmospheric Pressure Plasma Jet (APPJ)

    NASA Astrophysics Data System (ADS)

    Herrmann, Hans W.

    1998-11-01

    The atmospheric pressure plasma jet (APPJ) is a non-thermal, high pressure, uniform glow discharge that produces a high velocity effluent stream of highly reactive chemical species. The discharge operates on a feedstock gas (e.g. He/O_2/H_2O) which flows between an outer, grounded, cylindrical electrode and an inner, coaxial electrode powered at 13.56 MHz RF. While passing through the plasma, the feedgas becomes excited, dissociated or ionized by electron impact. Once the gas exits the discharge volume, ions and electrons are rapidly lost by recombination, but the fast-flowing effluent still contains metastables (e.g. O2*, He*) and radicals (e.g. O, OH). These reactive species have been shown to be effective neutralizers of surrogates for anthrax spores, mustard blister agent and VX nerve gas. Unlike conventional, wet decontamination methods, the plasma effluent does not cause corrosion of most surfaces and does not damage wiring, electronics, nor most plastics. This makes it highly suitable for decontamination of high value sensitive equipment such as is found in vehicle interiors (i.e. tanks, planes...) for which there is currently no good decontamination technique. Furthermore, the reactive species rapidly degrade into harmless products leaving no lingering residue or harmful byproducts. Physics of the APPJ will be discussed and results of surface decontamination experiments using simulant and actual CBW agents will be presented.

  4. Mechanisms behind surface modification of polypropylene film using an atmospheric-pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Shaw, David; West, Andrew; Bredin, Jerome; Wagenaars, Erik

    2016-12-01

    Plasma treatments are common for increasing the surface energy of plastics, such as polypropylene (PP), to create improved adhesive properties. Despite the significant differences in plasma sources and plasma properties used, similar effects on the plastic film can be achieved, suggesting a common dominant plasma constituent and underpinning mechanism. However, many details of this process are still unknown. Here we present a study into the mechanisms underpinning surface energy increase of PP using atmospheric-pressure plasmas. For this we use the effluent of an atmospheric-pressure plasma jet (APPJ) since, unlike most plasma sources used for these treatments, there is no direct contact between the plasma and the PP surface; the APPJ provides a neutral, radical-rich environment without charged particles and electric fields impinging on the PP surface. The APPJ is a RF-driven plasma operating in helium gas with small admixtures of O2 (0-1%), where the effluent propagates through open air towards the PP surface. Despite the lack of charged particles and electric fields on the PP surface, measurements of contact angle show a decrease from 93.9° to 70.1° in 1.4 s and to 35° in 120 s, corresponding to a rapid increase in surface energy from 36.4 mN m-1 to 66.5 mN m-1 in the short time of 1.4 s. These treatment effects are very similar to what is found in other devices, highlighting the importance of neutral radicals produced by the plasma. Furthermore, we find an optimum percentage of oxygen of 0.5% within the helium input gas, and a decrease of the treatment effect with distance between the APPJ and the PP surface. These observed effects are linked to two-photon absorption laser-induced fluorescence spectroscopy (TALIF) measurements of atomic oxygen density within the APPJ effluent which show similar trends, implying the importance of this radical in the surface treatment of PP. Analysis of the surface reveals a two stage mechanism for the production of polar

  5. Characterization of Atmospheric Pressure Plasma Jet (APPJ) and Its Effect on Plasmid DNA

    NASA Astrophysics Data System (ADS)

    Adhikari, Ek; Ptasinska, Sylwia

    2015-09-01

    A helium atmospheric pressure plasma jet (APPJ) source was constructed and then characterized by monitoring a deflected current on a high voltage electrode and a potential difference between two electrodes. The deflected current was also monitored for the APPJ source with varied electrical and fed gas composition e.g. admixtures of He and water vapor. The deflected power per cycle for gas admixtures was decreased with the increase in fraction of water vapor. In addition, this APPJ source was used to induce damage to aqueous plasmid DNA. The fraction of supercoiled, single-strand breaks and double-strand breaks in DNA were quantified by using agarose gel electrophoresis. The number of DNA strand breaks increased as a function of plasma irradiation time and decrease as a distance between APPJ and DNA sample increased. The APPJ with the gas admixture, in which the fraction of water vapor was varied, was also used to induce damage to aqueous DNA samples. The damage level decreased with the increase in a fraction of water vapor under specific experimental conditions. The change in numbers of DNA strand breaks irradiated by a pure He plasma and a plasma with a gas admixture is predicted by different physical and chemical process in the APPJ. This material is based upon work supported by the U.S. Department of Energy Office of Science, Office of Basic Energy Sciences under Award Number DE-FC02-04ER15533.

  6. Development of a radio frequency atmospheric pressure plasma jet for diamond-like carbon coatings on stainless steel substrates

    NASA Astrophysics Data System (ADS)

    Sohbatzadeh, F.; Samadi, O.; Siadati, S. N.; Etaati, G. R.; Asadi, E.; Safari, R.

    2016-10-01

    In this paper, an atmospheric pressure plasma jet with capacitively coupled radio frequency discharge was developed for diamond-like carbon (DLC) coatings on stainless steel substrates. The plasma jet was generated by argon-methane mixture and its physical parameters were investigated. Relation between the plasma jet length and width of the powered electrode was discussed. Optical and electrical characteristics were studied by optical emission spectroscopy, voltage and current probes, respectively. The evolutions of various species like ArI, C2 and CH along the jet axis were investigated. Electron temperature and density were estimated by Boltzmann plot method and Saha-Boltzmann equation, respectively. Finally, a diamond-like carbon coating was deposited on stainless steel-304 substrates by the atmospheric pressure radio frequency plasma jet in ambient air. Raman spectroscopy, scanning electron microscopy (SEM), atomic force microscopy and Vickers hardness test were used to study the deposited films. The length of the jet was increased by increasing the width of the powered electrode. The estimated electron temperature and density were 1.43 eV and 1.39 × 1015 cm-3, respectively. Averaged Vicker's hardness of the coated sample was three times greater than that of the substrate. The SEM images of the deposited thin films revealed a 4.5 μm DLC coated for 20 min.

  7. Detection of HO2 in an atmospheric pressure plasma jet using optical feedback cavity-enhanced absorption spectroscopy

    NASA Astrophysics Data System (ADS)

    Gianella, Michele; Reuter, Stephan; Lawry Aguila, Ana; Ritchie, Grant A. D.; van Helden, Jean-Pierre H.

    2016-11-01

    Cold non-equilibrium atmospheric pressure plasma jets are increasingly applied in material processing and plasma medicine. However, their small dimensions make diagnosing the fluxes of generated species a challenge. Here we report on the detection of the hydroperoxyl radical, HO2, in the effluent of a plasma jet by the use of optical feedback cavity-enhanced absorption spectroscopy. The spectrometer has a minimum detectable absorption coefficient {α }\\min of 2.25× {10}-10 cm-1 with a 100 second acquisition, equivalent to 5.5× {10}12 {{cm}}-3 of HO2 (under ideal conditions). Concentrations in the range of (3.1-7.8) × 1013 cm-3 were inferred in the 4 mm wide effluent of the plasma jet.

  8. The effects of added hydrogen on a helium atmospheric-pressure plasma jet ambient desorption/ionization source.

    PubMed

    Wright, Jonathan P; Heywood, Matthew S; Thurston, Glen K; Farnsworth, Paul B

    2013-03-01

    We present mass spectrometric data demonstrating the effect that hydrogen has on a helium-based dielectric-barrier discharge (DBD) atmospheric-pressure plasma jet used as an ambient desorption/ionization (ADI) source. The addition of 0.9 % hydrogen to the helium support gas in a 35-W plasma jet increased signals for a range of test analytes, with enhancement factors of up to 68, without proportional increases in background levels. The changes in signal levels result from a combination of changes in the desorption kinetics from the surface and increased ion production in the gas phase. The enhancement in ADI-MS performance despite the quenching of key plasma species reported in earlier studies suggests that ionization with a H2/He plasma jet is the result of an alternate mechanism involving the direct generation of ionized hydrogen.

  9. Cell immobilization on polymer by air atmospheric pressure plasma jet treatment

    NASA Astrophysics Data System (ADS)

    Lee, Jung-Hwan; Kwon, Jae-Sung; Om, Ji-yeon; Kim, Yong-Hee; Choi, Eun-Ha; Kim, Kwang-Mahn; Kim, Kyoung-Nam

    2014-08-01

    The study of cell immobilization on delicate polymer by an air atmospheric pressure plasma jet (AAPPJ) is required for its medical application. The aim of this study was to evaluate whether AAPPJ treatment induce cell immobilization effect on delicate polymers without significant change of surface roughness by AAPPJ treatment. After surface roughness, dynamic contact angle, and chemical characteristics were investigated, the immobilization effect was evaluated with the mouse fibroblast L929 cell line. Surface roughness change was not observed (P > 0.05) in either delicate dental wax or polystyrene plate (PSP) as advancing and receding contact angles significantly decreased (P < 0.05), thanks to decreased hydrocarbon and formation of oxygen-related functional groups in treated PSP. Adherent L929 cells with elongated morphology were found in treated PSP along with the formation of immobilization markers vinculin and actin cytoskeleton. Increased PTK2 gene expression upregulated these markers on treated PSP.

  10. Control of ROS and RNS productions in liquid in atmospheric pressure plasma-jet system

    NASA Astrophysics Data System (ADS)

    Uchida, Giichiro; Ito, Taiki; Takenaka, Kosuke; Ikeda, Junichiro; Setsuhara, Yuichi

    2016-09-01

    Non-thermal plasma jets are of current interest in biomedical applications such as wound disinfection and even treatment of cancer tumors. Beneficial therapeutic effects in medical applications are attributed to excited species of oxygen and nitrogen from air. However, to control the production of these species in the plasma jet is difficult because their production is strongly dependent on concentration of nitrogen and oxygen from ambient air into the plasma jet. In this study, we analyze the discharge characteristics and the ROS and RNS productions in liquid in low- and high-frequency plasma-jet systems. Our experiments demonstrated the marked effects of surrounding gas near the plasma jet on ROS and RNS productions in liquid. By controlling the surround gas, the O2 and N2 main plasma jets are selectively produced even in open air. We also show that the concentration ratio of NO2- to H2O2 in liquid is precisely tuned from 0 to 0.18 in deionized water by changing N2 gas ratio (N2 / (N2 +O2)) in the main discharge gas, where high NO2- ratio is obtained at N2 gas ratio at N2 / (N2 +O2) = 0 . 8 . The low-frequency plasma jet with controlled surrounding gas is an effective plasma source for ROS and RNS productions in liquid, and can be a useful tool for biomedical applications. This study was partly supported by a Grant-in-Aid for Scientific Research on Innovative Areas ``Plasma Medical Innovation'' (24108003) from the Ministry of Education, Culture, Sports, Science and Technology, Japan (MEXT).

  11. Plasma jet takes off.

    PubMed Central

    Frazer, L

    1999-01-01

    Thanks to a series of joint research projects by Los Alamos National Laboratory, Beta Squared of Allen, Texas, and the University of California at Los Angeles, there is now a more environmentally sound method for cleaning semiconductor chips that may also be effective in cleaning up chemical, bacterial, and nuclear contaminants. The Atmospheric Pressure Plasma Jet uses a type of ionized gas called plasma to clean up contaminants by binding to them and lifting them away. In contrast to the corrosive acids and chemical solvents traditionally used to clean semiconductor chips, the jet oxidizes contaminants, producing only benign gaseous by-products such as oxygen and carbon dioxide. The new technology is also easy to transport, cleans thoroughly and quickly, and presents no hazards to its operators. PMID:10417375

  12. Non-Thermal Equilibrium Atmospheric Pressure Glow-Like Discharge Plasma Jet

    NASA Astrophysics Data System (ADS)

    Chang, Zhengshi; Yao, Congwei; Zhang, Guanjun

    2016-01-01

    Non-thermal equilibrium atmospheric pressure plasma jet (APPJ) is a cold plasma source that promises various innovative applications, and the uniform APPJ is more favored. Glow discharge is one of the most effective methods to obtain the uniform discharge. Compared with the glow dielectric barrier discharge (DBD) in atmospheric pressure, pure helium APPJ shows partial characteristics of both the glow discharge and the streamer. In this paper, considering the influence of the Penning effect, the electrical and optical properties of He APPJ and Ar/NH3 APPJ were researched. A word “Glow-like APPJ” is used to characterize the uniformity of APPJ, and it was obtained that the basic characteristics of the glow-like APPJ are driven by the kHz AC high voltage. The results can provide a support for generating uniform APPJ, and lay a foundation for its applications. supported by National Natural Science Foundation of China (Nos. 51307133, 51125029, 51221005) and the Fundamental Research Funds for the Central Universities of China (Nos. xjj2012132, xkjc2013004)

  13. Dynamics of turbulent front at the correlation between atmospheric pressure plasma jet & gas flow field

    NASA Astrophysics Data System (ADS)

    Ghasemi, Maede; Xu, Haitao; Pei, Xuekai; Lu, Xinpei

    2016-09-01

    Among variety of plasma applications, there is significant interest recently in the use of plasma as an actuator in flow control for aerodynamic applications in which the correlation between atmospheric pressure plasma jet (APPJ) and gas flow field is a crucial role. In this contribution, dynamic characterizations of the turbulent flow field in APPj are investigated by focusing on the effect of different parameters of APPJ, such as applied voltage, pulse repetition frequency, gas flow rate, and time duration of the pulse We utilized Schlieren photography and photomultiplier tubes (PMT) as a signal triggering of an intensified charge coupled device (ICCD) and also a high speed camera to examine the formation of the turbulent front and its dynamics. The results reveal that the turbulent front will appear earlier and closer to the tube nozzle by increasing the gas flow rate and applied voltage amplitude. It is found that the pulse time duration and repetition frequency cannot change the dynamics and formation of the turbulent front. Further investigation demonstrated that every pulse can excite one turbulent front which is created in a specific position in a laminar region and propagates downstream and the effect of increasing frequency results in the increasing of the number of turbulent front and expansion of their region of formation.

  14. Self-consistent fluid modeling and simulation on a pulsed microwave atmospheric-pressure argon plasma jet

    SciTech Connect

    Chen, Zhaoquan; Yin, Zhixiang Chen, Minggong; Hong, Lingli; Hu, Yelin; Huang, Yourui; Xia, Guangqing; Liu, Minghai; Kudryavtsev, A. A.

    2014-10-21

    In present study, a pulsed lower-power microwave-driven atmospheric-pressure argon plasma jet has been introduced with the type of coaxial transmission line resonator. The plasma jet plume is with room air temperature, even can be directly touched by human body without any hot harm. In order to study ionization process of the proposed plasma jet, a self-consistent hybrid fluid model is constructed in which Maxwell's equations are solved numerically by finite-difference time-domain method and a fluid model is used to study the characteristics of argon plasma evolution. With a Guass type input power function, the spatio-temporal distributions of the electron density, the electron temperature, the electric field, and the absorbed power density have been simulated, respectively. The simulation results suggest that the peak values of the electron temperature and the electric field are synchronous with the input pulsed microwave power but the maximum quantities of the electron density and the absorbed power density are lagged to the microwave power excitation. In addition, the pulsed plasma jet excited by the local enhanced electric field of surface plasmon polaritons should be the discharge mechanism of the proposed plasma jet.

  15. The influence of electrode configuration on light emission profiles and electrical characteristics of an atmospheric-pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Maletić, Dejan; Puač, Nevena; Malović, Gordana; Đorđević, Antonije; Petrović, Zoran Lj

    2017-04-01

    In this paper we focus on the influence of the type of electrodes, their dimensions and inter-electrode gap on the formation of a helium plasma jet. Plasma emission profiles are recorded by an ICCD camera simultaneously with volt–ampere characteristics for three different copper electrode configurations. The delivered power was up to 6.5 W, but it may be set and controlled to 0.1 W. This study shows how the electrode configuration shapes and controls temporal and spatial plasma development as well as electrical characteristics of an atmospheric pressure plasma jet. It is shown that, in our system, the width of the grounded electrode has no significant influence on the formation and properties of pulsed atmospheric-pressure streamers (PAPS) outside the tube, while the width of the powered electrode is crucial in their formation.

  16. An Alternative to Annealing TiO2 Nanotubes for Morphology Preservation: Atmospheric Pressure Plasma Jet Treatment.

    PubMed

    Seo, Sang-Hee; Uhm, Soo-Hyuk; Kwon, Jae-Sung; Choi, Eun Ha; Kim, Kwang-Mahn; Kim, Kyoung-Nam

    2015-03-01

    Titanium oxide nanotube layer formed by plasma electrolytic oxidation (PEO) is known to be excellent in biomaterial applications. However, the annealing process which is commonly performed on the TiO2 nanotubes cause defects in the nanotubular structure. The purpose of this work was to apply a non-thermal atmospheric pressure plasma jet on diameter-controlled TiO2 nanotubes to mimic the effects of annealing while maintaining the tubular structure for use as biomaterial. Diameter-controlled nanotube samples fabricated by plasma electrolytic oxidation were dried and prepared under three different conditions: untreated, annealed at 450 °C for 1 h in air with a heating rate of 10 °C/min, and treated with an air-based non-thermal atmospheric pressure plasma jet for 5 minutes. The contact angle measurement was investigated to confirm the enhanced hydrophilicity of the TiO2 nanotubes. The chemical composition of the surface was studied using X-ray photoelectron spectroscopy, and the morphology of TiO2 nanotubes was examined by field emission scanning electron microscopy. For the viability of the cell, the attachment of the osteoblastic cell line MC3T3-E1 was determined using the water-soluble tetrazolium salt assay. We found that there are no morphological changes in the TiO2 nanotubular structure after the plasma treatment. Also, we investigated a change in the chemical composition and enhanced hydrophilicity which result in improved cell behavior. The results of this study indicated that the non-thermal atmospheric pressure plasma jet results in osteoblast functionality that is comparable to annealed samples while maintaining the tubular structure of the TiO2 nanotubes. Therefore, this study concluded that the use of a non-thermal atmospheric pressure plasma jet on nanotube surfaces may replace the annealing process following plasma electrolytic oxidation.

  17. Stark broadening measurement of the electron density in an atmospheric pressure argon plasma jet with double-power electrodes

    SciTech Connect

    Qian Muyang; Ren Chunsheng; Wang Dezhen; Zhang Jialiang; Wei Guodong

    2010-03-15

    Characteristics of a double-power electrode dielectric barrier discharge of an argon plasma jet generated at the atmospheric pressure are investigated in this paper. Time-averaged optical emission spectroscopy is used to measure the plasma parameters, of which the excitation electron temperature is determined by the Boltzmann's plot method whereas the gas temperature is estimated using a fiber thermometer. Furthermore, the Stark broadening of the hydrogen Balmer H{sub {beta}} line is applied to measure the electron density, and the simultaneous presence of comparable Doppler, van der Waals, and instrumental broadenings is discussed. Besides, properties of the jet discharge are also studied by electrical diagnosis. It has been found that the electron densities in this argon plasma jet are on the order of 10{sup 14} cm{sup -3}, and the excitation temperature, gas temperature, and electron density increase with the applied voltage. On the other hand, these parameters are inversely proportional to the argon gas flow rate.

  18. Surface pretreatment of plastics with an atmospheric pressure plasma jet - Influence of generator power and kinematics

    SciTech Connect

    Moritzer, E. Leister, C.

    2014-05-15

    The industrial use of atmospheric pressure plasmas in the plastics processing industry has increased significantly in recent years. Users of this treatment process have the possibility to influence the target values (e.g. bond strength or surface energy) with the help of kinematic and electrical parameters. Until now, systematic procedures have been used with which the parameters can be adapted to the process or product requirements but only by very time-consuming methods. For this reason, the relationship between influencing values and target values will be examined based on the example of a pretreatment in the bonding process with the help of statistical experimental design. Because of the large number of parameters involved, the analysis is restricted to the kinematic and electrical parameters. In the experimental tests, the following factors are taken as parameters: gap between nozzle and substrate, treatment velocity (kinematic data), voltage and duty cycle (electrical data). The statistical evaluation shows significant relationships between the parameters and surface energy in the case of polypropylene. An increase in the voltage and duty cycle increases the polar proportion of the surface energy, while a larger gap and higher velocity leads to lower energy levels. The bond strength of the overlapping bond is also significantly influenced by the voltage, velocity and gap. The direction of their effects is identical with those of the surface energy. In addition to the kinematic influences of the motion of an atmospheric pressure plasma jet, it is therefore especially important that the parameters for the plasma production are taken into account when designing the pretreatment processes.

  19. Atmospheric Pressure Plasma Jet in Ar and O2/Ar Mixtures: Properties and High Performance for Surface Cleaning

    NASA Astrophysics Data System (ADS)

    Jin, Ying; Ren, Chunsheng; Yang, Liang; Zhang, Jialiang; Wang, Dezhen

    2013-12-01

    An atmospheric pressure plasma jet generated in Ar and O2/Ar mixtures has been investigated by specially designed equipment with double power electrodes at 20~32 kHz, and their effects on the cleaning of surfaces have been studied. Properties of the jet discharge are studied by electrical diagnostics, including the waveform of discharge voltage, discharge current and the Q-V Lissajous figures. The optical emission spectroscopy is used to measure the plasma parameters, such as the excitation temperature and the gas temperature. It is found that the consumed power and the excitation temperature increase with increase of the discharge frequency. On the other hand, at the same discharge frequency, these parameters in O2/Ar mixture plasma are found to be much larger. The effect on surface cleaning is studied from the changes in the contact angle. For Ar plasma jet, the contact angle decreases with increase of the discharge frequency. For O2/Ar mixture plasma jet, the contact angle decreases with increase of discharge frequency up to 26 kHz, however, further increase of discharge frequency does not show further decrease in the contact angle. At the same discharge frequency, the contact angle after O2/Ar mixture plasma cleaning is found to be much lower compared to the case of pure Ar. From the results of quadrupole mass-spectrum analysis, we can identify more fragment molecules of CO and H2O in the emitted gases after O2/Ar plasma jet treatment compared with Ar plasma jet treatment, which are produced by the decomposition of surface organic contaminants during the cleaning process.

  20. Dual effects of atmospheric pressure plasma jet on skin wound healing of mice.

    PubMed

    Xu, Gui-Min; Shi, Xing-Min; Cai, Jing-Fen; Chen, Si-Le; Li, Ping; Yao, Cong-Wei; Chang, Zheng-Shi; Zhang, Guan-Jun

    2015-01-01

    Cold plasma has become an attractive tool for promoting wound healing and treating skin diseases. This article presents an atmospheric pressure plasma jet (APPJ) generated in argon gas through dielectric barrier discharge, which was applied to superficial skin wounds in BALB/c mice. The mice (n = 50) were assigned randomly into five groups (named A, B, C, D, E) with 10 animals in each group. Natural wound healing was compared with stimulated wound healing treated daily with APPJ for different time spans (10, 20, 30, 40, and 50 seconds) on 14 consecutive days. APPJ emission spectra, morphological changes in animal wounds, and tissue histological parameters were analyzed. Statistical results revealed that wound size changed over the duration of the experimental period and there was a significant interaction between experimental day and group. Differences between group C and other groups at day 7 were statistically significant (p < 0.05). All groups had nearly achieved closure of the untreated control wounds at day 14. The wounds treated with APPJ for 10, 20, 30, and 40 seconds showed significantly enhanced daily improvement compared with the control and almost complete closure at day 12, 10, 7, and 13, respectively. The optimal results of epidermal cell regeneration, granulation tissue hyperplasia, and collagen deposition in histological aspect were observed at day 7. However, the wounds treated for 50 seconds were less well healed at day 14 than those of the control. It was concluded that appropriate doses of cold plasma could inactivate bacteria around the wound, activate fibroblast proliferation in wound tissue, and eventually promote wound healing. Whereas, over doses of plasma suppressed wound healing due to causing cell death by apoptosis or necrosis. Both positive and negative effects may be related to the existence of reactive oxygen and nitrogen species (ROS and RNS) in APPJ.

  1. SnO2/CNT nanocomposite supercapacitors fabricated using scanning atmospheric-pressure plasma jets

    NASA Astrophysics Data System (ADS)

    Xu, Chang-Han; Chiu, Yi-Fan; Yeh, Po-Wei; Chen, Jian-Zhang

    2016-08-01

    SnO2/CNT electrodes for supercapacitors are fabricated by first screen-printing pastes containing SnO2 nanoparticles and CNTs on carbon cloth, following which nitrogen atmospheric pressure plasma jet (APPJ) sintering is performed at various APPJ scan rates. The APPJ scan rates change the time intervals for which the reactive plasma species and the heat of the nitrogen APPJs influence the designated sintering spot on the carbon cloth, resulting in APPJ-sintered SnO2/CNT nanocomposites with different properties. The water contact angle decreases with the APPJ scan rate. The improved wettability can facilitate the penetration of the electrolyte into the nanopores of the SnO2/CNT nanocomposites, thereby improving the charge storage and specific capacitance of the supercapacitors. Among the three tested APPJ scan rates, 1.5, 3, and 6 mm s-1, the SnO2/CNT supercapacitor sintered by APPJ under the lowest APPJ scan rate of 1.5 mm s-1 shows the best specific capacitance of ˜90 F g-1 as evaluated by cyclic voltammetry under a potential scan rate of 2 mV s-1. A high APPJ scan rate may result in low degree of materials activation and sintering, leading to poorer performance of SnO2/CNT supercapacitors. The results suggest the feasibility of an APPJ roll-to-roll process for the fabrication of SnO2/CNT nanocomposite supercapacitors.

  2. Discharge processes and an electrical model of atmospheric pressure plasma jets in argon

    NASA Astrophysics Data System (ADS)

    Fang, Zhi; Shao, Tao; Yang, Jing; Zhang, Cheng

    2016-01-01

    In this paper, an atmospheric pressure plasma discharge in argon was generated using a needle-to-ring electrode configuration driven by a sinusoidal excitation voltage. The electric discharge processes and discharge characteristics were investigated by inspecting the voltage-current waveforms, Lissajous curves and lighting emission images. The change in discharge mode with applied voltage amplitude was studied and characterised, and three modes of corona discharge, dielectric barrier discharge (DBD) and jet discharge were identified, which appeared in turn with increasing applied voltage and can be distinguished clearly from the measured voltage-current waveforms, light-emission images and the changing gradient of discharge power with applied voltage. Based on the experimental results and discharge mechanism analysis, an equivalent electrical model and the corresponding equivalent circuit for characterising the whole discharge processes accurately was proposed, and the three discharge stages were characterised separately. A voltage-controlled current source (VCCS) associated with a resistance and a capacitance were used to represent the DBD stage, and the plasma plume and corona discharge were modelled by a variable capacitor in series with a variable resistor. Other factors that can influence the discharge, such as lead and stray capacitance values of the circuit, were also considered in the proposed model. Contribution to the Topical Issue "Recent Breakthroughs in Microplasma Science and Technology", edited by Kurt Becker, Jose Lopez, David Staack, Klaus-Dieter Weltmann and Wei Dong Zhu.

  3. Syngas production from tar reforming by microwave plasma jet at atmospheric pressure: power supplied influence

    NASA Astrophysics Data System (ADS)

    de Souza Medeiros, Henrique; Justiniano, Lucas S.; Gomes, Marcelo P.; Soares da Silva Sobrinho, Argemiro; Petraconi Filho, Gilberto

    2013-09-01

    Now a day, scientific community is searching for new fuels able to replace fossil fuels with economic and environment gains and biofuel play a relevant rule, mainly for the transport sector. A major process to obtaining such type of renewable resource is biomass gasification. This process has as product a gas mixture containing CO, CH4, and H2 which is named synthesis gas (syngas). However, an undesirable high molecular organic species denominated tar are also produced in this process which must be removed. In this work, results of syngas production via tar reforming in the atmospheric pressure microwave discharge having as parameter the power supply. Argon, (argon + ethanol), and (argon + tar solution) plasma jet were produced by different values of power supplied (from 0.5 KW to 1.5 KW). The plasma compounds were investigated by optical spectroscopy to each power and gas composition. The main species observed in the spectrum are Ar, CN, OII, OIV, OH, H2, H(beta), CO2, CO, and SIII. This last one came from tar. The best value of the power applied to syngas production from tar reforming was verified between 1.0 KW and 1.2 KW. We thank the following institutions for financial support: CNPq, CAPES, and FAPESP.

  4. Diagnostics of AC excited Atmospheric Pressure Plasma Jet with He for Biomedical Applications

    NASA Astrophysics Data System (ADS)

    Hori, Masaru; Takeda, Keigo; Kumakura, Takumi; Ishikawa, Kenji; Tanaka, Hiromasa; Kondo, Hiroki; Sekine, Makoto; Nakai, Yoshihiro

    2014-10-01

    Atmospheric pressure plasma jets (APPJ) are frequently used for biomedical applications. Reactive species generated by the APPJ play important roles for treatments of biomedical samples. Therefore, high density APPJ sources are required to realize the high performance. Our group has developed AC excited Ar APPJ with electron density as high as 1015 cm-3, and realized the selective killing of cancer cells and the inactivate spores of Penicillium digitatum. Recently, a new spot-size AC excited APPJ with He gas have been developed. In this study, the He APPJ was characterized by using spectroscopy. The plasma was discharged at a He flow rate of 5 slm and a discharge voltage of AC 9 kV. Gas temperature and electron density of the APPJ were measured by optical emission spectroscopy. From theoretical fitting of 2nd positive system of N2 emission (380.4 nm) and Stark broadening of Balmer β line of H atom (486.1 nm), the gas temperature and the electron density was estimated to be 299 K and 3.4. × 1015 cm-3. The AC excited He APPJ has a potential to realize high density with room temperature and become a very powerful tool for biomedical applications.

  5. Development of atmospheric pressure large area plasma jet for sterilisation and investigation of molecule and plasma interaction

    NASA Astrophysics Data System (ADS)

    Zerbe, Kristina; Iberler, Marcus; Jacoby, Joachim; Wagner, Christopher

    2016-09-01

    The intention of the project is the development and improvement of an atmospheric plasma jet based on various discharge forms (e.g. DBD, RF, micro-array) for sterilisation of biomedical equipment and investigation of biomolecules under the influence of plasma stress. The major objective is to design a plasma jet with a large area and an extended length. Due to the success on small scale plasma sterilisation the request of large area plasma has increased. Many applications of chemical disinfection in environmental and medical cleaning could thereby be complemented. Subsequently, the interaction between plasma and biomolecules should be investigated to improve plasma strerilisation. Special interest will be on non equilibrium plasma electrons affecting the chemical bindings of organic molecules.

  6. Analysis of Ar plasma jets induced by single and double dielectric barrier discharges at atmospheric pressure

    NASA Astrophysics Data System (ADS)

    Judée, F.; Merbahi, N.; Wattieaux, G.; Yousfi, M.

    2016-09-01

    The aim is the comparison of different plasma parameters of single and double dielectric barrier discharge plasma jet configurations (S-DBD and D-DBD) which are potentially usable in biomedical applications. Both configurations are studied in terms of electric field distribution, electrical discharge characteristics, plasma parameters (estimated by optical emission spectroscopy analysis), and hydrodynamics of the plasma jet for electrical parameters of power supplies corresponding to an applied voltage of 10 kV, pulse duration of 1 μs, frequency of 9.69 kHz, and Ar flow of 2 l/min. We observed that the D-DBD configuration requires half the electrical power one needs to provide in the S-DBD case to generate a plasma jet with similar characteristics: excitation temperature around 4700 K, electron density around 2.5 × 1014 cm-3, gas temperature of about 320 K, a relatively high atomic oxygen concentration reaching up to 1000 ppm, the presence of reactive oxygen and nitrogen species (nitric oxide, hydroxyl radical, and atomic oxygen), and an irradiance in the UV-C range of about 20 μW cm-2. Moreover, it has been observed that D-DBD plasma jet is more sensitive to short pulse durations, probably due to the charge accumulation over the dielectric barrier around the internal electrode. This results in a significantly longer plasma length in the D-DBD configuration than in the S-DBD one up to a critical flow rate (2.25 l/min) before the occurrence of turbulence in the D-DBD case. Conversely, ionization wave velocities are significantly higher in the S-DBD setup (3.35 × 105 m/s against 1.02 × 105 m/s for D-DBD), probably due to the higher electrostatic field close to the high voltage electrode in the S-DBD plasma jet.

  7. Interactions Between Small Arrays of Atmospheric Pressure Micro-Plasma Jets: Gas Dynamic, Radiation and Electrostatic Interactions

    NASA Astrophysics Data System (ADS)

    Babaeva, Natalia

    2013-09-01

    Atmospheric pressure plasma jets are widely used devices for biomedical applications. A typical plasma jet consists of a tube through which noble gas or its mixture with a molecular gas flows. The noble gas creates a channel into the ambient air which is eventually dispersed by interdiffusion with the air. Plasma plumes are formed by the propagation of ionization waves (IWs) through the tubes and then through the noble gas phase channel. The IW typically propagates until the mole fraction of the ambient air in the channel increases above a critical values which requires a larger E/N to propagate the IW. By grouping several jets together to form an array of jets, one can in principle increase the area treated by the plume. If the jets are sufficiently far apart, the IWs and resulting plasma plumes are independent. As the spacing between the jets decreases, the plasma jets begin to mutually interact. In this talk, we discuss results from a computational investigation of small arrays of He/O2 micro-plasma jets propagating into ambient air. The model used in this work, nonPDPSIM, is a plasma hydrodynamics model in which continuity, momentum and energy equations are solved for charged and neutral species with solution of Poisson's equation for the electric potential. Navier-Stokes equations are solved for the gas dynamics and radiation transport is addressed using a propagator method. We found that as the spacing between the jets decreases, the He channels from the individual jets tend to merge. The IWs from each channel also merge into regions having the highest He mole fraction and so lowest E/N to sustain the IW. The proximity of the IWs enable other forms of interaction. If the IWs are of the same polarity, electrostatic forces can warp the paths of the IWs. If in sufficient proximity, the photoionization from one IW can influence its neighbors. The synchronization of the voltage pulses of adjacent IWs can also influence its neighbors. With synchronized pulses

  8. Identification of the biologically active liquid chemistry induced by a nonthermal atmospheric pressure plasma jet.

    PubMed

    Wende, Kristian; Williams, Paul; Dalluge, Joe; Gaens, Wouter Van; Aboubakr, Hamada; Bischof, John; von Woedtke, Thomas; Goyal, Sagar M; Weltmann, Klaus-Dieter; Bogaerts, Annemie; Masur, Kai; Bruggeman, Peter J

    2015-06-06

    The mechanism of interaction of cold nonequilibrium plasma jets with mammalian cells in physiologic liquid is reported. The major biological active species produced by an argon RF plasma jet responsible for cell viability reduction are analyzed by experimental results obtained through physical, biological, and chemical diagnostics. This is complemented with chemical kinetics modeling of the plasma source to assess the dominant reactive gas phase species. Different plasma chemistries are obtained by changing the feed gas composition of the cold argon based RF plasma jet from argon, humidified argon (0.27%), to argon/oxygen (1%) and argon/air (1%) at constant power. A minimal consensus physiologic liquid was used, providing isotonic and isohydric conditions and nutrients but is devoid of scavengers or serum constituents. While argon and humidified argon plasma led to the creation of hydrogen peroxide dominated action on the mammalian cells, argon-oxygen and argon-air plasma created a very different biological action and was characterized by trace amounts of hydrogen peroxide only. In particular, for the argon-oxygen (1%), the authors observed a strong negative effect on mammalian cell proliferation and metabolism. This effect was distance dependent and showed a half life time of 30 min in a scavenger free physiologic buffer. Neither catalase and mannitol nor superoxide dismutase could rescue the cell proliferation rate. The strong distance dependency of the effect as well as the low water solubility rules out a major role for ozone and singlet oxygen but suggests a dominant role of atomic oxygen. Experimental results suggest that O reacts with chloride, yielding Cl2(-) or ClO(-). These chlorine species have a limited lifetime under physiologic conditions and therefore show a strong time dependent biological activity. The outcomes are compared with an argon MHz plasma jet (kinpen) to assess the differences between these (at least seemingly) similar plasma sources.

  9. Atmospheric-pressure plasma-jet from micronozzle array and its biological effects on living cells for cancer therapy

    NASA Astrophysics Data System (ADS)

    Kim, Kangil; Choi, Jae Duk; Hong, Yong Cheol; Kim, Geunyoung; Noh, Eun Joo; Lee, Jong-Soo; Yang, Sang Sik

    2011-02-01

    We propose a plasma-jet device with a micrometer-sized nozzle array for use in a cancer therapy. Also, we show the biological effects of atmospheric-pressure plasma on living cells. Nitrogen-plasma activated a surrogate DNA damage signal transduction pathway, called the ataxia telangiectasia mutated (ATM)-checkpoint kinase 2 pathway, suggesting that the nitrogen-plasma generates DNA double-strand breaks. Phosphorylation of H2AX and p53 was detected in the plasma-treated cells, leading to apoptotic cell death. Thus, an effect for the nitrogen plasma in the control of apoptotic cell death provides insight into the how biological effects of the nitrogen-plasma can be applied to the control of cell survival, a finding with potential therapeutic implications.

  10. Comparison of two electro-hydrodynamic force models for the interaction between helium jet flow and an atmospheric-pressure "plasma jet"

    NASA Astrophysics Data System (ADS)

    Logothetis, D.; Papadopoulos, P. K.; Svarnas, P.; Vafeas, P.

    2016-12-01

    In this work, two simple phenomenological models of the electro-hydrodynamic force that arises in an atmospheric-pressure "plasma jet" are presented. The models are distinguished by the different boundary conditions applied for the consideration of the plasma propagation length. The comparison is based on numerical simulations, which are combined with experimental data, in order to determine the magnitude of the electro-hydrodynamic force and assess the ability of the two models to evaluate the visible plasma length. The results reveal that the gas flow characteristics depend on the spatial range of the force action and the force magnitude, and vice versa.

  11. Effect of non-thermal air atmospheric pressure plasma jet treatment on gingival wound healing

    NASA Astrophysics Data System (ADS)

    Lee, Jung-Hwan; Choi, Eun-Ha; Kim, Kwang-Mahn; Kim, Kyoung-Nam

    2016-02-01

    Non-thermal atmospheric pressure plasmas have been applied in the biomedical field for the improvement of various cellular activities. In dentistry, the healing of gingival soft tissue plays an important role in health and aesthetic outcomes. While the biomedical application of plasma has been thoroughly studied in dentistry, a detailed investigation of plasma-mediated human gingival fibroblast (HGF) migration for wound healing and its underlying biological mechanism is still pending. Therefore, the aim of this study is to apply a non-thermal air atmospheric pressure plasma jet (NTAAPPJ) to HGF to measure the migration and to reveal the underlying biological mechanisms involved in the migration. After the characterization of NTAAPPJ by optical emission spectroscopy, the adherent HGF was treated with NTAAPPJ or air with a different flow rate. Cell viability, lipid peroxidation, migration, intracellular reactive oxygen species (ROS), and the expression of migration-related genes (EGFR, PAK1, and MAPK3) were investigated. The level of statistical significance was set at 0.05. NTAAPPJ and air treatment with a flow rate of 250-1000 standard cubic centimetres per minute (sccm) for up to 30 s did not induce significant decreases in cell viability or membrane damage. A significant increase in the migration of mitomycin C-treated HGF was observed after 30 s of NTAAPPJ treatment compared to 30 s air-only treatment, which was induced by high levels of intracellular reactive oxygen species (ROS). An increase in migration-related gene expression and EGFR activation was observed following NTAAPPJ treatment in an air flow rate-dependent manner. This is the first report that NTAAPPJ treatment induces an increase in HGF migration without changing cell viability or causing membrane damage. HGF migration was related to an increase in intracellular ROS, changes in the expression of three of the migration-related genes (EGFR, PAK1, and MAPK1), and EGFR activation. Therefore

  12. Bacterial-killing effect of atmospheric pressure non-equilibrium plasma jet and oral mucosa response.

    PubMed

    Liu, Dexi; Xiong, Zilan; Du, Tianfeng; Zhou, Xincai; Cao, Yingguang; Lu, Xinpei

    2011-12-01

    Recently, plasma sterilization has attracted increasing attention in dental community for the atmospheric pressure non-equilibrium plasma jet (APNPs), which is driven by a kilohertz pulsed DC power, may be applied to the dental and oral diseases. However, it is still in doubt whether APNPs can effectively kill pathogenic bacteria in the oral cavity and produce no harmful effects on normal oral tissues, especially on normal mucosa. The aim of this study was to evaluate the bacterial-killing effect of APNPs in the biofilms containing a single breed of bacteria (Porphyromonas gingivalis, P.g.), and the pathological changes of the oral mucosa after treatment by APNPs. P.g. was incubated to form the biofilms in vitro, and the samples were divided into three groups randomly: group A (blank control); group B in which the biofilms were treated by APNPs (the setting of the equipment: 10 kHz, 1600 ns and 8 kV); group C in which the biofilms were exposed only to a gas jet without ignition of the plasma. Each group had three samples and each sample was processed for up to 5 min. The biofilms were then fluorescently stained, observed and photographed under a laser scanning confocal microscope. In the animal experiment, six male Japanese white rabbits were divided into two groups randomly (n=3 in each group) in terms of the different post-treatment time (1-day group and 5-day group). The buccal mucosa of the left side and the mucosa of the ventral surface of the tongue were treated by APNPs for 10 min in the same way as the bacterial biofilm experiment in each rabbit, and the corresponding mucosa of the other sides served as normal control. The clinical manifestations of the oral mucosa were observed and recorded every day. The rabbits were sacrificed one or five day(s) after APNPs treatment. The oral mucosa were harvested and prepared to haematoxylin and eosin-stained sections. Clinical observation and histopathological scores were used to assess mucosal changes. The results

  13. Investigation of metastable production in a closed-cell dielectric capillary variable pressure He plasma jet with Ar admixture

    NASA Astrophysics Data System (ADS)

    Sands, Brian; Ganguly, Biswa

    2011-10-01

    For plasma processing applications of streamer-like atmospheric pressure plasma jets generated in a dielectric capillary, we have demonstrated that an admixture of Ar to the He gas flow greatly increases the lifetime of energetic species in the core flow through enhanced afterglow production of Ar 1s5 metastable species. To study this effect in more detail, we have used a closed-cell plasma jet that allows control over the background gas pressure and composition. We used a 20 ns risetime positive unipolar voltage pulse for excitation. A He flow with a 0-30% Ar admixture was studied using time-resolved emission and tunable diode laser absorption spectroscopy of the Ar 1s5 and He 23S metastable states. Nitrogen was used as the background gas. In pure He and pure Ar gases the He and Ar metastables respectively are produced in the first ~100 ns only in the active discharge. With Ar added to the He gas flow, He metastables produced in the active discharge are quickly quenched via Penning ionization of Ar while Ar 1s5 is enhanced over 1-2 μs in the afterglow, increasing the number density as high as 1013/cc and extending the effective lifetime up to 10 μs. This implies that He heavy particle kinetics are a key driver of enhanced afterglow plasma chemistry in plasma jets with rare gas mixtures.

  14. Reactive species in humidity containing atmospheric pressure plasma jets - Numerical and experimental investigations

    NASA Astrophysics Data System (ADS)

    Schroeter, Sandra; Bredin, J.; Wijaikhum, A.; West, A.; Dedrick, J.; Niemi, K.; Gibson, A. R.; Foucher, M.; Booth, J.-P.; de Oliveira, N.; Joyeux, D.; Nahon, L.; Gorbanev, Y.; Chechik, V.; Wagenaars, E.; Gans, T.; O'Connell, D.

    2016-09-01

    The formation and absolute densities of oxygen and hydrogen containing reactive species such as atomic oxygen (O), hydrogen (H), hydroxyl radicals (OH) and hydrogen peroxide (H2O2) in an atmospheric pressure plasma jet (APPJ) are investigated as a function of the humidity content in the helium feed gas. APPJs are effective sources for these species, which are known to be biologically active and form a central role in their potential for biomedical applications. To develop and tailor APPJs for therapeutics, quantification of the reactive species produced is necessary. In this work, different diagnostic techniques, such as UV and VUV absorption spectroscopy and picosecond two-photon absorption laser-induced fluorescence (ps-TALIF) and a 0-dimensional chemical kinetics model are applied. We find that the densities of hydrogen containing species increase non-linearly with increasing feed gas humidity. The trend of atomic oxygen depends strongly on impurities present in the APPJ. The model results show that the dominant formation and destruction mechanisms of the species of interest are strongly influenced by the humidity content with different processes dominating at high and low humidity. Supported by UK EPSRC (EP/K018388/1, EP/H003797/1), the York-Paris CIRC and LABEX Plas@par (ANR11-IDEX-0004-02).

  15. Atmospheric-pressure plasma jet induces DNA double-strand breaks that require a Rad51-mediated homologous recombination for repair in Saccharomyces cerevisiae.

    PubMed

    Lee, Yoonna; Kim, Kangil; Kang, Kyu-Tae; Lee, Jong-Soo; Yang, Sang Sik; Chung, Woo-Hyun

    2014-10-15

    Non-thermal plasma generated under atmospheric pressure produces a mixture of chemically reactive molecules and has been developed for a number of biomedical applications. Recently, plasma jet has been proposed as novel cancer therapies based on the observation that free radicals generated by plasma jet induce mitochondria-mediated apoptotic cell death. We show here that air plasma jet induces DNA double-strand breaks (DSBs) in yeast chromosomes leading to genomic instability and loss of viability, which are alleviated by Rad51, the yeast homolog of Escherichiacoli RecA recombinase, through DNA damage repair by a homologous recombination (HR) process. Hypersensitivity of rad51 mutant to air plasma was not restored by antioxidant treatment unlike sod1 mutant that was highly sensitive to reactive oxygen species (ROS) challenge, suggesting that plasma jet induces DSB-mediated cell death independent of ROS generation. These results may provide a new insight into the mechanism of air plasma jet-induced cell death.

  16. Characterization of diamond-like carbon thin film synthesized by RF atmospheric pressure plasma Ar/CH4 jet

    NASA Astrophysics Data System (ADS)

    Sohbatzadeh, Farshad; Safari, Reza; Etaati, G. Reza; Asadi, Eskandar; Mirzanejhad, Saeed; Hosseinnejad, Mohammad Taghi; Samadi, Omid; Bagheri, Hanieh

    2016-01-01

    The growth of diamond like carbon (DLC) on a Pyrex glass was investigated by a radio frequency (RF) atmospheric pressure plasma jet (APPJ). The plasma jet with capacitive configuration ran by a radio frequency power supply at 13.56 MHz. Alumina ceramic was used as dielectric barrier. Ar and CH4 were used in atmospheric pressure as carrier and precursor gases, respectively. Diamond like carbon thin films were deposited on Pyrex glass at substrate temperature and applied power of 130 °C and 250 Watts, respectively. Performing field emission scanning electron microscope (FE-SEM) and laser Raman spectroscopy analysis resulted in deposition rate and the ID/IG ratio of 21.31 nm/min and 0.47, respectively. The ID/IG ratio indicated that the coating possesses relative high sp3 content The optical emission spectroscopy (OES) diagnostic was applied to diagnose plasma jet species. Estimating electron temperature and density of the RF-APPJ resulted in 1.36 eV and 2.75 × 1014 cm-3 at the jet exit, respectively.

  17. Influence of He/O 2 atmospheric pressure plasma jet treatment on subsequent wet desizing of polyacrylate on PET fabrics

    NASA Astrophysics Data System (ADS)

    Li, Xuming; Lin, Jun; Qiu, Yiping

    2012-01-01

    The influence of He/O2 atmospheric pressure plasma jet (APPJ) treatment on subsequent wet desizing of polyacrylate on PET fabrics was studied in the present paper. Weight loss results indicated that the weight loss increased with an increase of plasma treatment time. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) showed an increased surface roughness after the plasma treatment. SEM also showed that the fiber surfaces were as clean as unsized fibers after 35 s treatment followed by NaHCO3 desizing. X-ray photoelectron spectroscopy (XPS) analysis indicated that oxygen-based functional groups increased for the plasma treated polyacrylate sized fabrics. The percent desizing ratio (PDR) results showed that more than 99% PDR was achieved after 65 s plasma treatment followed by a 5 min NaHCO3 desizing. Compared to conventional wet desizing, indicating that plasma treatment could significantly reduce desizing time.

  18. Kinetic modelling for an atmospheric pressure argon plasma jet in humid air

    NASA Astrophysics Data System (ADS)

    Van Gaens, W.; Bogaerts, A.

    2013-07-01

    A zero-dimensional, semi-empirical model is used to describe the plasma chemistry in an argon plasma jet flowing into humid air, mimicking the experimental conditions of a setup from the Eindhoven University of Technology. The model provides species density profiles as a function of the position in the plasma jet device and effluent. A reaction chemistry set for an argon/humid air mixture is developed, which considers 84 different species and 1880 reactions. Additionally, we present a reduced chemistry set, useful for higher level computational models. Calculated species density profiles along the plasma jet are shown and the chemical pathways are explained in detail. It is demonstrated that chemically reactive H, N, O and OH radicals are formed in large quantities after the nozzle exit and H2, O2(1Δg), O3, H2O2, NO2, N2O, HNO2 and HNO3 are predominantly formed as ‘long living’ species. The simulations show that water clustering of positive ions is very important under these conditions. The influence of vibrational excitation on the calculated electron temperature is studied. Finally, the effect of varying gas temperature, flow speed, power density and air humidity on the chemistry is investigated.

  19. Effect of additive oxygen gas on cellular response of lung cancer cells induced by atmospheric pressure helium plasma jet

    NASA Astrophysics Data System (ADS)

    Joh, Hea Min; Choi, Ji Ye; Kim, Sun Ja; Chung, T. H.; Kang, Tae-Hong

    2014-10-01

    The atmospheric pressure helium plasma jet driven by pulsed dc voltage was utilized to treat human lung cancer cells in vitro. The properties of plasma plume were adjusted by the injection type and flow rate of additive oxygen gas in atmospheric pressure helium plasma jet. The plasma characteristics such as plume length, electric current and optical emission spectra (OES) were measured at different flow rates of additive oxygen to helium. The plasma plume length and total current decreased with an increase in the additive oxygen flow rate. The electron excitation temperature estimated by the Boltzmann plot from several excited helium emission lines increased slightly with the additive oxygen flow. The oxygen atom density in the gas phase estimated by actinometry utilizing argon was observed to increase with the additive oxygen flow. The concentration of intracellular reactive oxygen species (ROS) measured by fluorescence assay was found to be not exactly proportional to that of extracellular ROS (measured by OES), but both correlated considerably. It was also observed that the expression levels of p53 and the phospho-p53 were enhanced in the presence of additive oxygen flow compared with those from the pure helium plasma treatment.

  20. Effect of additive oxygen gas on cellular response of lung cancer cells induced by atmospheric pressure helium plasma jet.

    PubMed

    Joh, Hea Min; Choi, Ji Ye; Kim, Sun Ja; Chung, T H; Kang, Tae-Hong

    2014-10-16

    The atmospheric pressure helium plasma jet driven by pulsed dc voltage was utilized to treat human lung cancer cells in vitro. The properties of plasma plume were adjusted by the injection type and flow rate of additive oxygen gas in atmospheric pressure helium plasma jet. The plasma characteristics such as plume length, electric current and optical emission spectra (OES) were measured at different flow rates of additive oxygen to helium. The plasma plume length and total current decreased with an increase in the additive oxygen flow rate. The electron excitation temperature estimated by the Boltzmann plot from several excited helium emission lines increased slightly with the additive oxygen flow. The oxygen atom density in the gas phase estimated by actinometry utilizing argon was observed to increase with the additive oxygen flow. The concentration of intracellular reactive oxygen species (ROS) measured by fluorescence assay was found to be not exactly proportional to that of extracellular ROS (measured by OES), but both correlated considerably. It was also observed that the expression levels of p53 and the phospho-p53 were enhanced in the presence of additive oxygen flow compared with those from the pure helium plasma treatment.

  1. Effect of additive oxygen gas on cellular response of lung cancer cells induced by atmospheric pressure helium plasma jet

    PubMed Central

    Joh, Hea Min; Choi, Ji Ye; Kim, Sun Ja; Chung, T. H.; Kang, Tae-Hong

    2014-01-01

    The atmospheric pressure helium plasma jet driven by pulsed dc voltage was utilized to treat human lung cancer cells in vitro. The properties of plasma plume were adjusted by the injection type and flow rate of additive oxygen gas in atmospheric pressure helium plasma jet. The plasma characteristics such as plume length, electric current and optical emission spectra (OES) were measured at different flow rates of additive oxygen to helium. The plasma plume length and total current decreased with an increase in the additive oxygen flow rate. The electron excitation temperature estimated by the Boltzmann plot from several excited helium emission lines increased slightly with the additive oxygen flow. The oxygen atom density in the gas phase estimated by actinometry utilizing argon was observed to increase with the additive oxygen flow. The concentration of intracellular reactive oxygen species (ROS) measured by fluorescence assay was found to be not exactly proportional to that of extracellular ROS (measured by OES), but both correlated considerably. It was also observed that the expression levels of p53 and the phospho-p53 were enhanced in the presence of additive oxygen flow compared with those from the pure helium plasma treatment. PMID:25319447

  2. High-Density Polyethylene (HDPE) Surface Treatment Using an RF Capacitive Atmospheric Pressure Cold Ar Plasma Jet

    NASA Astrophysics Data System (ADS)

    Fei, Xiaomeng; Shin-ichi, Kuroda; Tamio, Mori; Katsuhiko, Hosoi

    2013-06-01

    In this study, a high-density polyethylene (HDPE, 5-mm-thick, 0.95 g/cm3) surface was treated using an RF capacitive atmospheric pressure cold Ar plasma jet. By using this Ar plasma jet, a hydrophilic HDPE surface was formed during the plasma treatment. In particular, the effects of an additive gas (N2 or O2) on the HDPE surface treatment were investigated in detail. It was shown that the addition of N2 or O2 gas had an important influence on the HDPE surface treatment. Compared to pure Ar plasma treatment, a lower value of water contact angle (WCA) was obtained when a trace of N2 or O2 gas was added. It was also found that besides the quantities of active species in the plasma jet, the treatment temperature played an important role in the HDPE surface treatment. This is because surface molecular motion is not negligible when the treatment temperature is close to the melting point of the polymer.

  3. Atmospheric pressure plasma jet in Ar and Ar/H{sub 2}O mixtures: Optical emission spectroscopy and temperature measurements

    SciTech Connect

    Sarani, Abdollah; Leys, Christophe; Nikiforov, Anton Yu.

    2010-06-15

    An atmospheric pressure plasma jet generated in Ar/water vapor mixtures has been investigated and the effect of water content on plasma properties has been studied. Plasma generated in Ar/water (0.05%) mixture shows higher intensity of OH radicals in emission spectra than pure argon alone. Plasma density has been estimated from current measurement and is in order of 1.5x10{sup 13} cm{sup -3}. Electron temperature has been estimated as 0.97 eV in pure Ar and it decreases with an increase in water content in plasma. The gas temperature has been determined by fitting of the experimental spectra and using the Boltzmann plot method. The gas temperature increases with the addition of water to feed gas from 620 K in pure Ar up to 1130 K for 0.76%H{sub 2}O.

  4. Membrane damage and active but nonculturable state in liquid cultures of Escherichia coli treated with an atmospheric pressure plasma jet.

    PubMed

    Dolezalova, Eva; Lukes, Petr

    2015-06-01

    Electrical discharge plasmas can efficiently inactivate various microorganisms. Inactivation mechanisms caused by plasma, however, are not fully understood because of the complexity of both the plasma and biological systems. We investigated plasma-induced inactivation of Escherichia coli in water and mechanisms by which plasma affects bacterial cell membrane integrity. Atmospheric pressure argon plasma jet generated at ambient air in direct contact with bacterial suspension was used as a plasma source. We determined significantly lower counts of E. coli after treatment by plasma when they were assayed using a conventional cultivation technique than using a fluorescence-based LIVE/DEAD staining method, which indicated that bacteria may have entered the viable-but-nonculturable state (VBNC). We did not achieve resuscitation of these non-culturable cells, however, we detected their metabolic activity through the analysis of cellular mRNA, which suggests that cells may have been rather in the active-but-nonculturable state (ABNC). We hypothesize that peroxidation of cell membrane lipids by the reactive species produced by plasma was an important pathway of bacterial inactivation. Amount of malondialdehyde and membrane permeability of E. coli to propidium iodide increased with increasing bacterial inactivation by plasma. Membrane damage was also demonstrated by detection of free DNA in plasma-treated water.

  5. Atmospheric-pressure plasma jets: Effect of gas flow, active species, and snake-like bullet propagation

    SciTech Connect

    Wu, S.; Wang, Z.; Huang, Q.; Tan, X.; Lu, X.; Ostrikov, K.

    2013-02-15

    Cold atmospheric-pressure plasma jets have recently attracted enormous interest owing to numerous applications in plasma biology, health care, medicine, and nanotechnology. A dedicated study of the interaction between the upstream and downstream plasma plumes revealed that the active species (electrons, ions, excited OH, metastable Ar, and nitrogen-related species) generated by the upstream plasma plume enhance the propagation of the downstream plasma plume. At gas flows exceeding 2 l/min, the downstream plasma plume is longer than the upstream plasma plume. Detailed plasma diagnostics and discharge species analysis suggest that this effect is due to the electrons and ions that are generated by the upstream plasma and flow into the downstream plume. This in turn leads to the relatively higher electron density in the downstream plasma. Moreover, high-speed photography reveals a highly unusual behavior of the plasma bullets, which propagate in snake-like motions, very differently from the previous reports. This behavior is related to the hydrodynamic instability of the gas flow, which results in non-uniform distributions of long-lifetime active species in the discharge tube and of surface charges on the inner surface of the tube.

  6. Preparation of nitrogen doped silicon oxides thin films by plasma polymerization of 3-aminopropyltriethoxylsilane using atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Lin, Yu-Chun; Wang, Meng-Jiy

    2016-01-01

    Surface modification techniques have been applied in various applications including self-cleaning surface, antibacterial filter, and biomaterials. In this study we employed the atmospheric pressure plasma jet (APPJ) deposition, a dry process for surface modification, to deposit 3-aminopropyltriethoxylsilane (APTES) on stainless steel (SS) on the purposes of simultaneously incorporating SiOx and nitrogen containing functionalities for the modulation of biofunctionality. The APPJ deposition allowed to form a thin layer of APTES with linear growth rate by controlling the deposition time. In addition, the surface chemical and physical properties, such as surface chemical composition, wettability, film thickness, and interactions with mammalian cells were evaluated by using different analytical methods. The results showed that the surface wettability was improved significantly due to the APTES deposition along with the increase of the incorporated nitrogen content. Moreover, the viability of L-929 fibroblasts was clearly promoted on the APTES deposited SS, which is most probably due to the thicker deposited films and higher density of nitrogen-containing functional groups. The outcomes of this research showed great potential to apply on metallic substrates in real time for biomedical related applications.

  7. Measurement of O and OH radical produced by an atmospheric-pressure helium plasma jet nearby rat skin

    NASA Astrophysics Data System (ADS)

    Yonemori, Seiya; Ono, Ryo

    2013-09-01

    Atmospheric-pressure helium plasma jet is getting much attention because it enables many kinds of plasma applications including biomedical application such as sterilization and cancer treatment. In biomedical plasma applications, it is though that active species like ions and radicals play important role. Especially, OH radical and O atom is very chemically reactive that they are deemed as major factors in cancer treatment. In this study, O and OH density distribution and its temporal behavior nearby rat skin were measured to demonstrate actual application. Plasma discharge was under AC10 kVp-p, 10 kHz with 1.5 slm (standard litter per minute) of helium gas flow. OH density was around 1 ppm and O atom density was around 10 ppm at maximum. We also measured time-evolution of OH and O atom density. Both OH and O density was almost constant between discharge pulses because lifetime of active species could be prolonged in helium. And density distribution of both species varied depending on helium flow rate and water concentration on the surface; on rat skin or on the grass surface. Those results suggest the production mechanisms and provision mechanisms of O atom and OH radical by an atmospheric-pressure helium plasma jet. This work is partially supported by the Grant-in-Aid for Science Research by the Ministry of Education, Culture, Sport, Science and Technology.

  8. Feed gas humidity: a vital parameter affecting a cold atmospheric-pressure plasma jet and plasma-treated human skin cells

    NASA Astrophysics Data System (ADS)

    Winter, J.; Wende, K.; Masur, K.; Iseni, S.; Dünnbier, M.; Hammer, M. U.; Tresp, H.; Weltmann, K.-D.; Reuter, S.

    2013-07-01

    In this study, the effect of feed gas humidity on the reactive component generation of an atmospheric-pressure argon plasma jet and its effect on human skin cells are investigated. Feed gas humidity is identified as one key parameter that strongly influences stability and reproducibility of plasma medical studies. The plasma jet is investigated by absorption spectroscopy in the ultraviolet and infrared spectral region for its ozone production depending on the humidity concentration in the feed gas. By optical emission spectroscopy the dependence of present excited plasma species such as hydroxyl radicals, molecular nitrogen, argon and atomic oxygen on the feed gas humidity is investigated. As an interface layer between the plasma jet effluent and the biological cell, a buffer solution is treated and the hydrogen peroxide (H2O2) production is studied with two independent colorimetric assays as a function of humidity admixture to the feed gas. Ultimately, the effect of varying feed gas humidity on the cell viability of indirect plasma treated adherent HaCAT cells is investigated. The highest viability is found for the driest feed gas condition. Furthermore, this work shows answers for the relevance of unwanted—or intended—feed gas humidity in plasma medical experiments and their comparatively large relevance with respect to ambient humidity. The findings will lead to more reproducible experiments in the field of plasma medicine.

  9. An experimental study on discharge characteristics in a pulsed-dc atmospheric pressure CH3OH/Ar plasma jet

    NASA Astrophysics Data System (ADS)

    Qian, Muyang; Liu, Sanqiu; Yang, Congying; Pei, Xuekai; Lu, Xinpei; Zhang, Jialiang; Wang, Dezhen

    2016-10-01

    Recently, C/H/Ar plasma discharges found enormous potential and possibility in carbonaceous compounds conversion and production. In this work, a pulsed-dc CH3OH/Ar plasma jet generated at atmospheric pressure is investigated by means of optical and electrical diagnosis concerning the variation of its basic parameters, absolute concentration of OH radicals, and plasma temperature with different CH3OH/Ar volume ratios, in the core region of discharge with needle-to-ring electrode configuration. The voltage-current characteristics are also measured at different CH3OH/Ar ratios. Laser-induced fluorescence (LIF) results here show that only small amounts of added methanol vapor to argon plasma (about 0.05% CH3OH/Ar volume ratio) is favorable for the production of OH radicals. The optical emission lines of CH, CN, and C2 radicals have been detected in the CH3OH/Ar plasma. And, the plasma temperatures increase with successive amount of added methanol vapor to the growth plasma. Moreover, qualitative discussions are presented regarding the mechanisms for methanol dissociation and effect of the CH3OH component on the Ar plasma discharge at atmospheric pressure.

  10. Plasma effects on the generation of reactive oxygen and nitrogen species in cancer cells in-vitro exposed by atmospheric pressure pulsed plasma jets

    NASA Astrophysics Data System (ADS)

    Kim, Sun Ja; Chung, T. H.

    2015-08-01

    Atmospheric pressure pulsed helium plasma jets are utilized for plasma-cell interactions. The effect of operating parameters such as applied voltage, pulse repetition frequency, and duty ratio on the generation of specific reactive oxygen and nitrogen species in gas and liquid phases and within cells is investigated. The apoptotic changes detected by terminal deoxynucleotidyl transferase (TdT)-mediated dUTP nick-end labeling assay in cells caused by plasma exposure are observed to correlate well with the levels of extracellular and intracellular reactive oxygen and nitrogen species.

  11. Optical emission spectroscopic diagnostics of a non-thermal atmospheric pressure helium-oxygen plasma jet for biomedical applications

    NASA Astrophysics Data System (ADS)

    Thiyagarajan, Magesh; Sarani, Abdollah; Nicula, Cosmina

    2013-06-01

    In this work, we have applied optical emission spectroscopy diagnostics to investigate the characteristics of a non-thermal atmospheric pressure helium plasma jet. The discharge characteristics in the active and afterglow region of the plasma jet, that are critical for biomedical applications, have been investigated. The voltage-current characteristics of the plasma discharge were analyzed and the average plasma power was measured to be around 18 W. The effect of addition of small fractions of oxygen at 0.1%-0.5% on the plasma jet characteristics was studied. The addition of oxygen resulted in a decrease in plasma plume length due to the electronegativity property of oxygen. Atomic and molecular lines of selected reactive plasma species that are considered to be useful to induce biochemical reactions such as OH transitions A2Σ+(ν=0,1)→X2Π(Δν =0) at 308 nm and A2Σ+(ν=0,1)→X2Π(Δν =1) at 287 nm, O I transitions 3p5P→3s5S0 at 777.41 nm, and 3p3P→3s3S0 at 844.6 nm, N2(C-B) second positive system with electronic transition C3Πu→B3Πg in the range of 300-450 nm and N2+(B-X) first negative system with electronic transition B2Σu+→X2Σg+(Δν =0) at 391.4 nm have been studied. The atomic emission lines of helium were identified, including the He I transitions 3p3P0→2s3S at 388.8 nm, 3p1P0→ 2s1S at 501.6 nm, 3d3D→2p3P0 at 587.6 nm, 3d1D→2p1P0 at 667.8 nm, 3s3S1→2p3P0 at 706.5 nm, 3s1S0→2p1P0 at 728.1 nm, and Hα transition 2p-3d at 656.3 nm. Using a spectral fitting method, the OH radicals at 306-312 nm, the rotational and vibrational temperatures equivalent to gas temperatures of the discharge was measured and the effective non-equilibrium nature of the plasma jet was demonstrated. Our results show that, in the entire active plasma region, the gas temperature remains at 310 ± 25 K and 340 ± 25 K and it increases to 320 ± 25 K and 360 ± 25 K in the afterglow region of the plasma jet for pure helium and helium/oxygen (0.1%) mixture

  12. In vitro bactericidal efficacy of atmospheric-pressure plasma jet on titanium-based implant infected with Staphylococcus aureus

    NASA Astrophysics Data System (ADS)

    Park, Young-Ouk; Lee, Chang-Min; Kim, Myung-Sun; Jung, Sang-Chul; Yang, Seong-Won; Kook, Min-Suk; Kim, Byung-Hoon

    2017-01-01

    Staphylococcus aureus is a representative of gram-positive bacteria that causes skin infection, respiratory diseases, and burned tissue infections. The aim of this study was to evaluate the sterilizing efficiency of an atmospheric-pressure plasma jet (APPJ) on S. aureus adhered on a titanium surface. During the APPJ sterilization, the plasma gases used were Ar, Ar+N2, and Ar+O2. With increasing APPJ treatment time, the viability of S. aureus decreased. The addition of O2 gas to Ar gas resulted in a higher sterilizing efficiency than the addition of other groups. Plasma exposure induced bacterial oxidative stress, and it was confirmed that the cell membrane was seriously damaged by the production of reactive oxygen species. Our finding suggests that the APPJ is an effective tool for clinical antimicrobial therapy.

  13. Use of molecular beacons for the rapid analysis of DNA damage induced by exposure to an atmospheric pressure plasma jet

    SciTech Connect

    Kurita, Hirofumi E-mail: mizuno@ens.tut.ac.jp; Miyachika, Saki; Yasuda, Hachiro; Takashima, Kazunori; Mizuno, Akira E-mail: mizuno@ens.tut.ac.jp

    2015-12-28

    A rapid method for evaluating the damage caused to DNA molecules upon exposure to plasma is demonstrated. Here, we propose the use of a molecular beacon for rapid detection of DNA strand breaks induced by atmospheric pressure plasma jet (APPJ) irradiation. Scission of the molecular beacon by APPJ irradiation leads to separation of the fluorophore-quencher pair, resulting in an increase in fluorescence that directly correlates with the DNA strand breaks. The results show that the increase in fluorescence intensity is proportional to the exposure time and the rate of fluorescence increase is proportional to the discharge power. This simple and rapid method allows the estimation of DNA damage induced by exposure to a non-thermal plasma.

  14. Removal of naturally grown human biofilm with an atmospheric pressure plasma jet: An in-vitro study.

    PubMed

    Jablonowski, Lukasz; Fricke, Katja; Matthes, Rutger; Holtfreter, Birte; Schlüter, Rabea; von Woedtke, Thomas; Weltmann, Klaus-Dieter; Kocher, Thomas

    2016-08-19

    The removal of biofilm is a prerequisite for a successful treatment of biofilm-associated diseases. In this study, we compared the feasibility of an atmospheric pressure plasma device with a sonic powered brush to remove naturally grown supragingival biofilm from extracted teeth. Twenty-four periodontally hopeless teeth were extracted. Argon jet plasma with an oxygen admixture of 1 vol% and a sonically driven brush were used to remove biofilm with application times of 60 s, 180 s and 300 s. The treatment efficiency was assessed with light microscopy, scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The highest biofilm removal rate was observed after an application time of 180 s/300 s with the sonic brush (80.4%/86.2%), plasma (75.5%/89.0%). These observations were confirmed by SEM. According to XPS analysis, plasma treatment decreased the amount of carbon and nitrogen, indicative of an extensive removal of proteins. Plasma treatment of naturally grown biofilm resulted in an effective cleaning of the tooth surface and was comparable to mechanical treatment. Treatment time had a significant influence on plaque reduction. These results showed that plasma could be a useful adjuvant treatment modality in cases where biofilm removal or reduction plays a decisive role, such as periodontitis and peri-implantitis. Plasma-treated biofilm on an extracted tooth.

  15. Two-dimensional numerical study of two counter-propagating helium plasma jets in air at atmospheric pressure

    SciTech Connect

    Yan, Wen; Sang, Chaofeng; Wang, Dezhen; Liu, Fucheng

    2014-06-15

    In this paper, a computational study of two counter-propagating helium plasma jets in ambient air is presented. A two-dimensional fluid model is applied to investigate the physical processes of the two plasma jets interaction (PJI) driven by equal and unequal voltages, respectively. In all studied cases, the PJI results in a decrease of both plasma bullets propagation velocity. When the two plasma jets are driven by equal voltages, they never merge but rather approach each other around the middle of the gas gap at a minimum approach distance, and the minimal distance decreases with the increase of both the applied voltages and initial electron density, but increases with the increase of the relative permittivity. When the two plasma jets are driven by unequal voltages, we observe the two plasma jets will merge at the position away from the middle of the gas gap. The effect of applied voltage difference on the PJI is also studied.

  16. Mechanisms of bacterial inactivation in the liquid phase induced by a remote RF cold atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    van Gils, C. A. J.; Hofmann, S.; Boekema, B. K. H. L.; Brandenburg, R.; Bruggeman, P. J.

    2013-05-01

    A radio-frequency atmospheric pressure argon plasma jet is used for the inactivation of bacteria (Pseudomonas aeruginosa) in solutions. The source is characterized by measurements of power dissipation, gas temperature, absolute UV irradiance as well as mass spectrometry measurements of emitted ions. The plasma-induced liquid chemistry is studied by performing liquid ion chromatography and hydrogen peroxide concentration measurements on treated distilled water samples. Additionally, a quantitative estimation of an extensive liquid chemistry induced by the plasma is made by solution kinetics calculations. The role of the different active components of the plasma is evaluated based on either measurements, as mentioned above, or estimations based on published data of measurements of those components. For the experimental conditions being considered in this work, it is shown that the bactericidal effect can be solely ascribed to plasma-induced liquid chemistry, leading to the production of stable and transient chemical species. It is shown that HNO2, ONOO- and H2O2 are present in the liquid phase in similar quantities to concentrations which are reported in the literature to cause bacterial inactivation. The importance of plasma-induced chemistry at the gas-liquid interface is illustrated and discussed in detail.

  17. Evaluation of fatty acid oxidation by reactive oxygen species induced in liquids using atmospheric-pressure nonthermal plasma jets

    NASA Astrophysics Data System (ADS)

    Tani, Atsushi; Fukui, Satoshi; Ikawa, Satoshi; Kitano, Katsuhisa

    2015-10-01

    We investigated fatty acid oxidation by atmospheric-pressure nonthermal helium plasma using linoleic acid, an unsaturated fatty acid, together with evaluating active species induced in liquids. If the ambient gas contains oxygen, direct plasma such as plasma jets coming into contact with the liquid surface supplies various active species, such as singlet oxygen, ozone, and superoxide anion radicals, to the liquid. The direct plasma easily oxidizes linoleic acid, indicating that fatty acid oxidation will occur in the direct plasma. In contrast, afterglow flow, where the plasma is terminated in a glass tube and does not touch the surface of the liquid sample, supplies mainly superoxide anion radicals. The fact that there was no clear observation of linoleic acid oxidation using the afterglow reveals that it may not affect lipids, even in an atmosphere containing oxygen. The afterglow flow can potentially be used for the sterilization of aqueous solutions using the reduced pH method, in medical and dental applications, because it provides bactericidal activity in the aqueous solution despite containing a smaller amount of active species.

  18. Control of TTIP Solution for Atmospheric Pressure Plasma Jet and Deposition of TiO2 Micro-particles

    NASA Astrophysics Data System (ADS)

    Hayakawa, Masahiro; Parajulee, Shankar; Ikezawa, Shunjiro

    TiO2 deposition-methods are versatile and are expected to be more simple and easy, however, in recent years the industrial photocatalytic products have been developed enormously. In this work, photocatalytic TiO2 micro-particles are deposited using the atmospheric pressure plasma jet device. Here, deposition-method is carried out in two steps, at first, the hydrolysis reaction time has been able to control which will resolve the TTIP coagulating trouble during the transportation, by acidifying the solution with AA (Acetic acid) and DEA (Diethanolamine). An experiment was performed to measure the hydrolysis reaction time of TTIP (Titanium tetraisopropoxide) solution by He-Ne laser. Secondly, the deposition of TiO2 micro-particles was carried out using the atmospheric pressure plasma jet with the controlled TTIP solution in reaction time. Based on SEM and water contact angle measurement, it is found that the smaller the mixing ratios of TTIP and DEA the smaller the TiO2 particle size. Also, the smaller the TiO2 particles the smaller the contact angle under the UV irradiation which suffices the photocatalytic behavior.

  19. Two-photon absorption laser induced fluorescence measurement of atomic oxygen density in an air atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Conway, Jim; Gogna, Gurusharan; Daniels, Stephen

    2016-09-01

    Two-photon Absorption Laser Induced Fluorescence (TALIF) is used to measure atomic oxygen number density [O] in an air Atmospheric Pressure Plasma Jet (APPJ). A novel technique based on photolysis of O2 is used to calibrate the TALIF system ensuring the same species (O) is probed during calibration and measurement. As a result, laser intensity can be increased outside the TALIF quadratic laser power region without affecting calibration reliability as any high intensity saturation effects will be identical for calibration and experiment. Higher laser intensity gives stronger TALIF signals helping overcome weak TALIF signals often experienced at atmospheric pressure due to collisional quenching. O2 photo-dissociation and two-photon excitation of the resulting [O] are both achieved within the same laser pulse. The photolysis [O] is spatially non-uniform and time varying. To allow valid comparison with [O] in a plasma, spatial and temporal correction factors are required. Knowledge of the laser pulse intensity I0(t), and wavelength allows correction factors to be found using a rate equation model. The air flow into the jet was fixed and the RF power coupled into the system varied. The resulting [O] was found to increase with RF power.

  20. Enhancement of cell growth on honeycomb-structured polylactide surface using atmospheric-pressure plasma jet modification

    NASA Astrophysics Data System (ADS)

    Cheng, Kuang-Yao; Chang, Chia-Hsing; Yang, Yi-Wei; Liao, Guo-Chun; Liu, Chih-Tung; Wu, Jong-Shinn

    2017-02-01

    In this paper, we compare the cell growth results of NIH-3T3 and Neuro-2A cells over 72 h on flat and honeycomb structured PLA films without and with a two-step atmospheric-pressure nitrogen-based plasma jet treatment. We developed a fabrication system used for forming of a uniform honeycomb structure on PLA surface, which can produce two different pore sizes, 3-4 μm and 7-8 μm, of honeycomb pattern. We applied a previously developed nitrogen-based atmospheric-pressure dielectric barrier discharge (DBD) jet system to treat the PLA film without and with honeycomb structure. NIH-3T3 and a much smaller Neuro-2A cells were cultivated on the films under various surface conditions. The results show that the two-step plasma treatment in combination with a honeycomb structure can enhance cell growth on PLA film, should the cell size be not too smaller than the pore size of honeycomb structure, e.g., NIH-3T3. Otherwise, cell growth would be better on flat PLA film, e.g., Neuro-2A.

  1. Effects of the electrical excitation signal parameters on the geometry of an argon-based non-thermal atmospheric pressure plasma jet.

    PubMed

    Benabbas, Mohamed Tahar; Sahli, Salah; Benhamouda, Abdallah; Rebiai, Saida

    2014-12-01

    A non-thermal atmospheric pressure argon plasma jet for medical applications has been generated using a high-voltage pulse generator and a homemade dielectric barrier discharge (DBD) reactor with a cylindrical configuration. A plasma jet of about 6 cm of length has been created in argon gas at atmospheric pressure with an applied peak to peak voltage and a frequency of 10 kV and 50 kHz, respectively. The length and the shape of the created plasma jet were found to be strongly dependent on the electrode setup and the applied voltage and the signal frequency values. The length of the plasma jet increases when the applied voltage and/or its frequency increase, while the diameter at its end is significantly reduced when the applied signal frequency increases. For an applied voltage of 10 kV, the plasma jet diameter decreases from near 5 mm for a frequency of 10 kHz to less than 1 mm at a frequency of 50 kHz. This obtained size of the plasma jet diameter is very useful when the medical treatment must be processed in a reduced space. PACS 2008: 52.50.Dg; 52.70.-m; 52.80.-s.

  2. Fast functionalization of multi-walled carbon nanotubes by an atmospheric pressure plasma jet.

    PubMed

    Kolacyak, Daniel; Ihde, Jörg; Merten, Christian; Hartwig, Andreas; Lommatzsch, Uwe

    2011-07-01

    The afterglow of an atmospheric pressure plasma has been used for the fast oxidative functionalization of multi-walled carbon nanotubes (MWCNTs). Scanning electron microscopy and Raman spectroscopy demonstrate that the MWCNT morphology is mostly preserved when the MWCNTs are dispersed in a solvent and injected as a spray into the plasma. Contact angle measurements show that this approach enhances the wettability of MWCNTs and reduces their sedimentation in an aqueous dispersion. X-ray photoelectron spectroscopy, IR spectroscopy, and electrokinetic measurements show that oxygen plasma incorporates about 6.6 at.% of oxygen and creates mainly hydroxyl and carboxyl functional groups on the MWCNT surface. The typical effective treatment time is estimated to be in the range of milliseconds. The approach is ideally suited for combination with the industrial gas phase CVD synthesis of MWCNTs.

  3. Assessment of the roles of various inactivation agents in an argon-based direct current atmospheric pressure cold plasma jet

    SciTech Connect

    Zhang Qian; Wang Ruixue; Sun Peng; Feng Hongqing; Liang Yongdong; Zhu Weidong; Becker, Kurt H.; Zhang Jue; Fang Jing

    2012-06-15

    Three types of gases, pure argon (99.999%), argon with 2% oxygen, and argon with 2% oxygen and 10% nitrogen were used as operating gases of a direct current atmospheric pressure cold plasma jet to inactivate Staphylococcus aureus (S. aureus) suspended in a liquid. The inactivation efficacies for the plasma jets operating in the three gases decrease from Ar/O{sub 2}(2%) to Ar/O{sub 2}(2%)/N{sub 2}(10%) to pure Ar. Optical emission spectroscopy, electron spin resonance spectroscopy, high performance liquid chromatography, and atomic absorption spectrophotometry were employed to identify and monitor the reactive species in the plasma-liquid system for the three operating gases and revealed the presence of O, {sup 1}O{sub 2}, OH, NO, H{sub 2}O{sub 2}, O{sub 3}, and NO{sub 3}{sup -}/NO{sub 2}{sup -} as well as Cu{sup +}/Cu{sup 2+}. The S. aureus inactivation results indicate that atomic oxygen (O) is the key inactivation agent, while other species play a lesser role in the inactivation progress studied here.

  4. High-temperature and high-speed oxidation of 4H-SiC by atmospheric pressure thermal plasma jet

    NASA Astrophysics Data System (ADS)

    Hanafusa, Hiroaki; Ishimaru, Ryosuke; Higashi, Seiichiro

    2017-04-01

    The application of atmospheric pressure thermal plasma jet (TPJ) annealing to the high-temperature and high-speed thermal oxidation of Si-face of 4H-SiC wafer is reported. A high SiO2 film growth rate of 288 nm min‑1 was obtained at an oxidation temperature of 1640 °C without intentional dry O2 gas feeding. Ambient analysis suggested that ozone generated from oxygen in the ambient air by the plasma irradiation was supplied to the SiC surface. It is implied that a mono-oxygen decomposed from ozone was diffused into the oxide growth interface. As a result, high-speed oxidation occurred by combination of high-temperature TPJ annealing and ozone feeding.

  5. Characterization of Damage to Bacteria and Bio-macromolecules Caused by (V)UV Radiation and Particles Generated by a Microscale Atmospheric Pressure Plasma Jet

    NASA Astrophysics Data System (ADS)

    Lackmann, Jan-Wilm; Schneider, Simon; Narberhaus, Franz; Benedikt, Jan; Bandow, Julia E.

    Atmospheric pressure plasma jets effectively inactivate bacteria on ­surfaces including infected tissues. This is due to the combined effects of (V)UV radiation, reactive oxygen and nitrogen species, ions, and high electric fields. A well-characterized microscale atmospheric pressure plasma jet (μ-APPJ) operated with He/O2 gas mixture has been modified so that (V)UV radiation and heavy reactive particles (mainly O3 molecules and O atoms) emitted from the plasma source can be separated effectively. The separation is achieved by an additional lateral He flow, which diverts the heavy particles from the jet axis. The new jet geometry is called X-Jet. Separation of different plasma components allows studying their effects on living cells and bio-macromolecules separately. First, the effectiveness of the separation of different plasma components was demonstrated by treatment of monolayers of vegetative Bacillus subtilis cells. To characterize effects on nucleic acids, dried plasmid DNA and total cellular RNA were treated with the separated plasma components. Dried bovine serum albumin was used to study etching effects of (V)UV radiation and heavy particles on proteins. We found that heavy particles emitted from the X-Jet kill vegetative cells more effectively than the (V)UV radiation from this type of plasma source. All bio-macromolecules investigated, DNA, RNA, and proteins, are affected by plasma treatment. DNA exposed to the (V)UV-channel of the jet seems to be prone to thymine dimer formation not only in vitro but also in vivo as indicated by induction of the photolyase in Escherichia coli, while DNA strand breaks occur under both jet channels. Heavy particles seem more effective in degrading RNA and in etching protein in vitro.

  6. Atmospheric pressure plasma jet treatment evokes transient oxidative stress in HaCaT keratinocytes and influences cell physiology.

    PubMed

    Wende, Kristian; Straßenburg, Susanne; Haertel, Beate; Harms, Manuela; Holtz, Sarah; Barton, Annemarie; Masur, Kai; von Woedtke, Thomas; Lindequist, Ulrike

    2014-04-01

    Modern non-thermal atmospheric pressure plasma sources enable controllable interaction with biological systems. Their future applications - e.g. wound management - are based on their unique mixture of reactive components sparking both stimulatory as well as inhibitory processes. To gain detailed understanding of plasma-cell interaction and with respect to risk awareness, key mechanisms need to be identified. This study focuses on the impact of an argon non-thermal atmospheric pressure plasma jet (kINPen 09) on human HaCaT keratinocytes. With increasing duration, cell viability decreased. In accordance, cells accumulated in G2/M phase within the following 24 h. DNA single-strand breaks were detected immediately after treatment and receded in the aftermath, returning to control levels after 24 h. No directly plasma-related DNA double-strand breaks were detected over the same time. Concurrently, DNA synthesis decreased. Coincident with treatment time, an increase in intracellular 2',7'-dichlorodihydrofluorescein diacetate (H(2)DCFDA) conversion increased reactive oxygen species (ROS) levels. The radical scavenging activity of culture medium crucially influenced these effects. Thus, ROS changed DNA integrity, and the effectiveness of cellular defence mechanisms characterises the interaction of non-thermal plasma and eukaryotic cells. Effects were time-dependent, indicating an active response of the eukaryotic cells. Hence, a stimulation of eukaryotic cells using short-term non-thermal plasma treatment seems possible, eg in the context of chronic wound care. Long-term plasma treatments stopped in cell proliferation and apoptosis, which might be relevant in controlling neoplastic conditions.

  7. Hypersonic Induced Interactions of Plasma and Non-Plasma Jets

    DTIC Science & Technology

    2006-06-12

    optimised . A preliminary assessment of the effects of plasma actuators on jet and jet in crossflow was conducted. NOMENCLATURE C Chapman-Rubesin...highly adaptable so as to allow for efficient changeover between the use of different geometries . The model was a zero incidence flat plate with a...Final Report: FA8655-07-1-3032 / Kontis, K Figure 7: Schematic of flat plate geometry Table 1 Pressure tappings. The non-plasma air jet was

  8. EDITORIAL: Plasma jets and plasma bullets Plasma jets and plasma bullets

    NASA Astrophysics Data System (ADS)

    Kong, M. G.; Ganguly, B. N.; Hicks, R. F.

    2012-06-01

    Plasma plumes, or plasma jets, belong to a large family of gas discharges whereby the discharge plasma is extended beyond the plasma generation region into the surrounding ambience, either by a field (e.g. electromagnetic, convective gas flow, or shock wave) or a gradient of a directionless physical quantity (e.g. particle density, pressure, or temperature). This physical extension of a plasma plume gives rise to a strong interaction with its surrounding environment, and the interaction alters the properties of both the plasma and the environment, often in a nonlinear and dynamic fashion. The plasma is therefore not confined by defined physical walls, thus extending opportunities for material treatment applications as well as bringing in new challenges in science and technology associated with complex open-boundary problems. Some of the most common examples may be found in dense plasmas with very high dissipation of externally supplied energy (e.g. in electrical, optical or thermal forms) and often in or close to thermal equilibrium. For these dense plasmas, their characteristics are determined predominantly by strong physical forces of different fields, such as electrical, magnetic, thermal, shock wave, and their nonlinear interactions [1]. Common to these dense plasma plumes are significant macroscopic plasma movement and considerable decomposition of solid materials (e.g. vaporization). Their applications are numerous and include detection of elemental traces, synthesis of high-temperature materials and welding, laser--plasma interactions, and relativistic jets in particle accelerators and in space [2]-[4]. Scientific challenges in the understanding of plasma jets are exciting and multidisciplinary, involving interweaving transitions of all four states of matter, and their technological applications are wide-ranging and growing rapidly. Using the Web of Science database, a search for journal papers on non-fusion plasma jets reveals that a long initial phase up

  9. Effects of the electrical parameters and gas flow rate on the generation of reactive species in liquids exposed to atmospheric pressure plasma jets

    NASA Astrophysics Data System (ADS)

    Baek, Eun Jeong; Joh, Hea Min; Kim, Sun Ja; Chung, T. H.

    2016-07-01

    In this work, an atmospheric pressure plasma jet was fabricated and studied for plasma-liquid interactions. The plasma jet consists of a quartz-covered pin electrode and outer quartz tube with a tapered nozzle. Using the current-voltage (I-V) and optical emission characteristics of the plasma jet, the plasma density and the speed of the plume were investigated. The optical emission spectra clearly indicated the excited NO, O, OH, N2, and N2+ in the plasma plumes. Then the plasma jets were applied to the deionized water. We investigated the effects of the operating parameters such as applied voltage, pulse frequency, and gas flow rate on the generation of reactive species in the gas and liquid phases. The densities of reactive species including OH radicals were obtained at the plasma-liquid surface and inside the plasma-treated liquids using ultraviolet absorption spectroscopy and chemical probe method. The nitrite concentration was detected by Griess assay. The data are very suggestive that there is a strong correlation among the production of reactive oxygen and nitrogen species (RONS) in the plasmas and liquids.

  10. PECVD of SiOC Films Using a Sheet-type Atmospheric Pressure Plasma Jet

    NASA Astrophysics Data System (ADS)

    Nakajima, Kouta; Tanaka, Kenji; Shirafuji, Tatsuru

    2015-09-01

    Packaging industries have used SiOC thin films for gas barrier coatings on the membranes for packaging foods, drug, and so on. PECVD is the most extensively employed method for preparing the SiOC films. However, PECVD is a process performed at a low pressure in general and requires expensive vacuum systems, especially in the case of large area coatings. Atmospheric pressure PECVD is a candidate to overcome this issue. If we simply apply atmospheric pressure plasma to CVD processes, however, we will encounter the problem of particle formation because of the high collision frequency in the environment of atmospheric pressure. In this work, we have developed a reactor that utilizes a unique gas-flow scheme for avoiding the particle formation. We have successfully deposited SiOC films by using this reactor, in which the source material is hexamethyldisiloxane and discharge/carrier gas is He. XPS measurements on the SiOC films have revealed that the films contain relatively higher concentrations of unfavorable methyl groups that reduce gas barrier performances. However, no particulates are involved in and on the deposited films as long as characterizing the films with eye observation and with transmission electron microscopy.

  11. A comparison between micro hollow cathode discharges and atmospheric pressure plasma jets in Ar/O2 gas mixtures

    NASA Astrophysics Data System (ADS)

    Lazzaroni, C.; Chabert, P.

    2016-12-01

    Using global models, micro hollow cathode discharges (MHCDs) are compared to radiofrequency atmospheric pressure plasma jets (APPJs) in terms of reactive oxygen species (ROS) production. Ar/O2 gas mixtures are investigated, typically with a small percentage of oxygen in argon. The same chemical reaction set, involving 17 species and 128 chemical reactions in the gas phase, is used for both devices, operated in the typical geometries previously published; the APPJ is driven by a radiofrequency voltage across a 1 mm gap, at atmospheric pressure, while the MHCD is driven by a DC voltage source, at 100 Torr and in a 400 μm hole. The MHCD may be operated either in the self-pulsing or in the normal (stationary) regime, depending on the driving voltage. The comparison shows that in both regimes, the MHCD produces larger amounts of \\text{O}2\\ast , while the APPJ produces predominantly reactive oxygen ground state species, \\text{O} and {{\\text{O}}3} . These large differences in ROS composition are mostly due to the higher plasma density produced in the MHCD. The difference in operating pressure is a second order effect.

  12. Partial hydrophilic modification of biaxially oriented polypropylene film by an atmospheric pressure plasma jet with the allylamine monomer

    NASA Astrophysics Data System (ADS)

    Chen, W. X.; Yu, J. S.; Hu, W.; Chen, G. L.

    2016-11-01

    In this paper, the partial modification of the biaxially oriented polypropylene (BOPP) film for potential biological and packaging applications was achieved via hydrophilic modification using atmospheric pressure plasma jet (APPJ). In the APPJ system, the allylamine (ALA) monomer was polymerized on the BOPP surface by either the Ar/O2 or the He/O2 plasma. The results showed that plasmatic modification created many micro/nano sized holes on the BOPP film, which increased the surface roughness dramatically and the increased roughness enhanced the combining intensity between the BOPP film and the ALA polymer. However, such a plasmatic modification increased the water vapor permeability. The FTIR and XPS characterizations showed that the amine groups were grafted onto the BOPP film, and the contact angle of the BOPP film decreases from 98.5° to 8°. Compared with the BOPP films treated by the Ar or He plasma, the barrier property of the modified BOPP film increased significantly when the ALA polymer was incorporated. The bio-affinity/toxicity of ALA polymer was illustrated by the attachment of the cultured SMMC-7721 hepatoma cells on the modified BOPP film. The significant enhancement in the cell density indicated that modified BOPP film was highly bio-compatible and non-toxic, especially treated with the Ar/O2/ALA plasma.

  13. In vitro antimicrobial effects and mechanism of atmospheric-pressure He/O2 plasma jet on Staphylococcus aureus biofilm

    NASA Astrophysics Data System (ADS)

    Xu, Zimu; Shen, Jie; Cheng, Cheng; Hu, Shuheng; Lan, Yan; Chu, Paul K.

    2017-03-01

    The antimicrobial effects and associated mechanism of inactivation of Staphylococcus aureus (S. aureus) NCTC-8325 biofilms induced by a He/O2 atmospheric-pressure plasma jet (APPJ) are investigated in vitro. According to CFU (colony forming units) counting and the resazurin-based assay, the 10 min He/O2 (0.5%) APPJ treatment produces the optimal inactivation efficacy (>5 log10 ml‑1) against the S. aureus biofilm and 5% of the bacteria enter a viable but non-culturable (VBNC) state. Meanwhile, 94% of the bacteria suffer from membrane damage according to SYTO 9/PI counterstaining. Scanning electron microscopy (SEM) reveals that plasma exposure erodes the extracellular polymeric substances (EPS) and then the cellular structure. The H2DCFDA-stained biofilms show larger concentrations of intracellular reactive oxygen species (ROS) in membrane-intact bacteria with increasing plasma dose. The admixture of oxygen in the working gas highly contributes to the deactivation efficacy of the APPJ against S. aureus and the plasma-induced endogenous ROS may work together with the discharge-generated ROS to continuously damage the bacterial membrane structure leading to deactivation of the biofilm microbes.

  14. Effects of assisted magnetic field to an atmospheric-pressure plasma jet on radical generation at the plasma-surface interface and bactericidal function

    NASA Astrophysics Data System (ADS)

    Liu, Chih-Tung; Kumakura, Takumi; Ishikawa, Kenji; Hashizume, Hiroshi; Takeda, Keigo; Ito, Masafumi; Hori, Masaru; Wu, Jong-Shinn

    2016-12-01

    A configuration of magnetic-assisted-plasma (MAP) on helium-based atmospheric-pressure plasma jet (APPJ) with an axial magnetic-field of 0.587 T is proposed, which provides good ability for killing bacteria Escherichia coli on the agar surface. Optically, we confirmed that the MAP increased approximately 2.4 times in the electron density estimated by the Stark broadening of H β line emission, and approximately 1.5 times enhancement of atomic oxygen concentration measured by vacuum ultraviolet absorption spectroscopy (VUVAS). Moreover, the generation of hydroxyl radical in the water increased 1.5 times, confirmed by the spin-trapping electron spin-resonance technique. In addition, the bactericidal experiments demonstrated 2.4 times higher for E. coli by the MAP treatment. The MAP configuration is proposed to be highly useful for future bio-medical applications by enhancing the radical generation at the plasma/substrate interface region.

  15. Multiplying probe for accurate power measurements on an RF driven atmospheric pressure plasma jet applied to the COST reference microplasma jet

    NASA Astrophysics Data System (ADS)

    Beijer, P. A. C.; Sobota, A.; van Veldhuizen, E. M.; Kroesen, G. M. W.

    2016-03-01

    In this paper a new multiplying probe for measuring the power dissipated in a miniature capacitively coupled, RF driven, atmospheric pressure plasma jet (μAPPJ—COST Reference Microplasma Jet—COST RMJ) is presented. The approach aims for substantially higher accuracy than provided by traditionally applied methods using bi-directional power meters or commercially available voltage and current probes in conjunction with digitizing oscilloscopes. The probe is placed on a miniature PCB and designed to minimize losses, influence of unknown elements, crosstalk and variations in temperature. The probe is designed to measure powers of the order of magnitude of 0.1-10 W. It is estimated that it measures power with less than 2% deviation from the real value in the tested power range. The design was applied to measure power dissipated in COST-RMJ running in helium with a small addition of oxygen.

  16. Effect of discharge polarity on the propagation of atmospheric-pressure helium plasma jets and the densities of OH, NO, and O radicals.

    PubMed

    Yonemori, Seiya; Ono, Ryo

    2015-06-01

    The atmospheric-pressure helium plasma jet is an emerging technology for plasma biomedical applications. In this paper, the authors focus on the effect of discharge polarity on propagation of the discharge and the densities of OH, NO, and O radicals. The plasma jet is applied to a glass surface placed on a grounded metal plate. Positive or negative voltage pulses with 25 μs duration, 8 kV amplitude, and 10 kpps repetition rate are used for the plasma jet. The plasma propagation is measured using a short-gated ICCD camera. The light emission intensity of the discharge generated at the rising phase of the voltage pulse is approximately equivalent for both polarities, while that generated during the falling phase is much higher for the negative discharge than the positive one. The shape of the discharge changes with the discharge polarity. The OH, NO, and O densities in the plasma jet are also measured for both polarities. It is found that the OH density is almost the same regardless the discharge polarity. Conversely, the negative discharge produces more O atoms and the positive discharge produces more NO molecules. These results indicate that the polarity of the discharge affects the densities of some reactive species produced in the plasma jet.

  17. Flexible reduced graphene oxide supercapacitor fabricated using a nitrogen dc-pulse atmospheric-pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Yang, Cheng-Han; Kuok, Fei-Hong; Liao, Chen-Yu; Wan, Ting-Hao; Chen, Chieh-Wen; Hsu, Cheng-Che; Cheng, I.-Chun; Chen, Jian-Zhang

    2017-02-01

    We use a nitrogen dc-pulse atmospheric-pressure plasma jet to fabricate a flexible reduced graphene oxide (rGO) supercapacitor with polyvinyl alcohol (PVA)/sulfuric acid (H2SO4) gel electrolyte. An areal capacitance of 47.03 mF · cm‑2 (evaluated using cyclic voltammetry (CV) under a potential scan rate of 2 mV · s‑1) is achieved. The supercapacitor can be operated without apparent degradation under bending with a bending radius of 0.55 cm. After a 1000 cycle CV stability test, the capacitance retention rate is 100% when flat and is 98.6% under bending (bending radius  =  0.55 cm), indicating promising stability of the APPJ-processed flexible supercapacitor.

  18. Wettability and sizing property improvement of raw cotton yarns treated with He/O 2 atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Sun, Shiyuan; Sun, Jie; Yao, Lan; Qiu, Yiping

    2011-01-01

    Raw cotton fiber is water repellent due to the existence of the water repellent cuticle layer. This study is designed to systematically investigate how He/O 2 atmospheric pressure plasma jet (APPJ) treatments influence the wettability and the sizing property of cotton yarns. Water absorption time and adhesion of the sizing agent to the cotton roving are used to evaluate the improvement of wettability and sizing property of the yarn respectively. The water absorption time decreases with the increase of the treatment time and the oxygen flow rate, and the decrease of the jet to substrate distance (JTSD). An optimal water absorption time of 0.8 s is obtained with a treatment time of 20 s, JTSD of 1 mm and O 2 flow rate of 0.2 L/min. Scanning electron microscopy (SEM) shows that the etching effect increases with the decrease of the JTSD and X-ray photoelectron spectroscopy (XPS) presents increased oxygen contents after the plasma treatments. An increase of O-C dbnd O bonds while a decrease of C-OH/C-O-C bonds are observed when the JTSD is set at 2 mm. However, a remarkable increase of both C-OH/C-O-C and O-C dbnd O bonds are achieved when the JTSD is 1 mm. The roving impregnation test results show a nearly doubled adhesion of sizing and a slightly improved breaking elongation, indicating that the plasma treatment does effectively enhance the bonding strength between the fiber and the sizing.

  19. A Revival of Waste: Atmospheric Pressure Nitrogen Plasma Jet Enhanced Jumbo Silicon/Silicon Carbide Composite in Lithium Ion Batteries.

    PubMed

    Chen, Bing-Hong; Chuang, Shang-I; Liu, Wei-Ren; Duh, Jenq-Gong

    2015-12-30

    In this study, a jumbo silicon/silicon carbide (Si/SiC) composite (JSC), a novel anode material source, was extracted from solar power industry cutting waste and used as a material for lithium-ion batteries (LIBs), instead of manufacturing the nanolized-Si. Unlike previous methods used for preventing volume expansion and solid electrolyte interphase (SEI), the approach proposed here simply entails applying surface modification to JSC-based electrodes by using nitrogen-atmospheric pressure plasma jet (N-APPJ) treatment process. Surface organic bonds were rearranged and N-doped compounds were formed on the electrodes through applying different plasma treatment durations, and the qualitative examinations of before/after plasma treatment were identified by X-ray photoelectron spectroscopy (XPS) and electron probe microanalyzer (EPMA). The surface modification resulted in the enhancement of electrochemical performance with stable capacity retention and high Coulombic efficiency. In addition, depth profile and scanning electron microscope (SEM) images were executed to determine the existence of Li-N matrix and how the nitrogen compounds change the surface conditions of the electrodes. The N-APPJ-induced rapid surface modification is a major breakthrough for processing recycled waste that can serve as anode materials for next-generation high-performance LIBs.

  20. Influence of absorbed moisture on desizing of poly(vinyl alcohol) on cotton fabrics during atmospheric pressure plasma jet treatment

    NASA Astrophysics Data System (ADS)

    Peng, Shujing; Liu, Xiulan; Sun, Jie; Gao, Zhiqiang; Yao, Lan; Qiu, Yiping

    2010-04-01

    This paper studies the influence of moisture absorption of cotton fabrics on the effectiveness of atmospheric pressure plasma jet (APPJ) on desizing of polyvinyl alcohol (PVA). Cotton fabrics with three different moisture regains (MR), namely 1.8%, 7.3%, and 28.4% corresponding to 10%, 65%, and 98% of relative humidity respectively, are treated for 16 s, 32 s, 48 s, and 64 s. X-ray photoelectron spectroscopy analysis indicates that the plasma treated PVA has higher oxygen concentration than the control. Mass loss results show that the fabric with the highest MR has the largest mass loss after 64 s plasma exposure. Solubility measurement reveals that the sample with the lowest MR has the highest desizing efficacy and the percent desizing ratio reaches 96% after 64 s exposure plus a 20 min hot wash, which is shown as clean as the unsized sample through scanning electron microscopy analysis. The yarn tensile strength test results show that APPJ has no negative effect on fabric tensile strength.

  1. Merging of high speed argon plasma jets

    SciTech Connect

    Case, A.; Messer, S.; Brockington, S.; Wu, L.; Witherspoon, F. D.; Elton, R.

    2013-01-15

    Formation of an imploding plasma liner for the plasma liner experiment (PLX) requires individual plasma jets to merge into a quasi-spherical shell of plasma converging on the origin. Understanding dynamics of the merging process requires knowledge of the plasma phenomena involved. We present results from the study of the merging of three plasma jets in three dimensional geometry. The experiments were performed using HyperV Technologies Corp. 1 cm Minirailguns with a preionized argon plasma armature. The vacuum chamber partially reproduces the port geometry of the PLX chamber. Diagnostics include fast imaging, spectroscopy, interferometry, fast pressure probes, B-dot probes, and high speed spatially resolved photodiodes, permitting measurements of plasma density, temperature, velocity, stagnation pressure, magnetic field, and density gradients. These experimental results are compared with simulation results from the LSP 3D hybrid PIC code.

  2. DC-driven plasma gun: self-oscillatory operation mode of atmospheric-pressure helium plasma jet comprised of repetitive streamer breakdowns

    NASA Astrophysics Data System (ADS)

    Wang, Xingxing; Shashurin, Alexey

    2017-02-01

    This paper presents and studies helium atmospheric pressure plasma jet comprised of a series of repetitive streamer breakdowns, which is driven by pure DC high voltage (self-oscillatory behavior). The repetition frequency of the breakdowns is governed by the geometry of discharge electrodes/surroundings and gas flow rate. Each next streamer is initiated when the electric field on the anode tip recovers after the previous breakdown and reaches the breakdown threshold value of about 2.5 kV cm-1. One type of the helium plasma gun designed using this operational principle is demonstrated. The gun operates on about 3 kV DC high voltage and is comprised of the series of the repetitive streamer breakdowns at a frequency of about 13 kHz.

  3. Inhibitory effect of silver nanoparticles mediated by atmospheric pressure air cold plasma jet against dermatophyte fungi.

    PubMed

    Ouf, Salama A; El-Adly, Amira A; Mohamed, Abdel-Aleam H

    2015-10-01

    In an in vitro study with five clinical isolates of dermatophytes, the MIC(50) and MIC(100) values of silver nanoparticles (AgNPs) ranged from 5 to 16 and from 15 to 32 μg ml(- 1), respectively. The combined treatment of AgNPs with atmospheric pressure-air cold plasma (APACP) induced a drop in the MIC(50) and MIC100 values of AgNPs reaching 3-11 and 12-23 μg ml(- 1), respectively, according to the examined species. Epidermophyton floccosum was the most sensitive fungus to AgNPs, while Trichophyton rubrum was the most tolerant. AgNPs induced significant reduction in keratinase activity and an increase in the mycelium permeability that was greater when applied combined with plasma treatment. Scanning electron microscopy showed electroporation of the cell walls and the accumulation of AgNPs on the cell wall and inside the cells, particularly when AgNPs were combined with APACP treatment. An in vivo experiment with dermatophyte-inoculated guinea pigs indicated that the application of AgNPs combined with APACP was more efficacious in healing and suppressing disease symptoms of skin as compared with the application of AgNPs alone. The recovery from the infection reached 91.7 % in the case of Microsporum canis-inoculated guinea pigs treated with 13 μg ml(- 1) AgNPs combined with APACP treatment delivered for 2  min. The emission spectra indicated that the efficacy of APACP was mainly due to generation of NO radicals and excited nitrogen molecules. These reactive species interact and block the activity of the fungal spores in vitro and in the skin lesions of the guinea pigs. The results achieved are promising compared with fluconazole as reference antifungal drug.

  4. Computational study of the afterglow in single and sequential pulsing of an atmospheric-pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Hasan, M. I.; Bradley, J. W.

    2015-10-01

    The spatial distribution of charged species in the afterglow of a helium plasma jet impinging atmospheric air has been computed using a 2D axisymmetric fluid model. The model is solved for two consecutive pulse periods of a rectangular voltage waveform (duration of 60 ns) and for two different frequencies (25 and 50 kHz). The most abundant ionic species in the afterglow are found to be \\text{O}2+ and \\text{O}2- with their concentrations increasing by about an order of magnitude (up to about 1018 m-3 and 1017 m-3 respectively) in the initial 1 μs. In the first pulse, these species form a halo around the diffusing He+ and electron rich central channel, the shape of the former being strongly correlated with the shape of He-air mixing layer computed using a hydrodynamic model. In the next pulse, this general configuration is also observed; however \\text{O}2+ is more concentrated on the axis of the jet, this being due to influence of residual electrons in the central channel. For \\text{O}2- there is little difference in their spatial distribution compared to the initial pulse. For higher frequency pulsing, the higher concentration of residual electrons lowers the necessary ignition electric field reducing the concentrations (by 25%) of charged species in a period of the applied waveform. This work provides new information on the concentration and distribution of ionic species generated by atmospheric-pressure capillary discharges of interest to those developing such sources for range of applications, particularly in the field of plasma medicine.

  5. Optimization of micropipette fabrication by laser micromachining for application in an ultrafine atmospheric pressure plasma jet using response surface methodology

    NASA Astrophysics Data System (ADS)

    Wang, Tao; Liu, Jingquan; Yang, Bin; Chen, Xiang; Wang, Xiaolin; Yang, Chunsheng

    2016-06-01

    The optimization of the laser micromachining process for special tapered micropipettes was investigated using response surface methodology. Three process parameters for the CO2 laser-based micropipette puller (P-2000, Sutter Instrument) were chosen as variables, namely heat, velocity and pull. The targeted length L TVS of the tapered variant section with a tip diameter of 10 μm was taken as a response. The optimum process parameters with L TVS of 7.3 mm were determined by analyzing the response surface three-dimension surface plots. The central composite design was selected to optimize the process variables, and the experimental data were fitted into a reduced cubic polynomial model. The high R 2 value (99.66%) and low coefficient of variation (0.73%) indicated the statistical significance of the model and good precision for the experiment. The optimization result showed that the best parameters were with the heat, velocity and pull values of 850, 53 and 170, respectively. The result was verified by a CO2 laser-based micropipette puller three times with length L TVS at 7.26 mm, 7.35 mm and 7.36 mm with the same optimized parameters. Then, the application to the ultrafine atmospheric pressure He/O2 plasma jets was carried out and micro-hole etching of the parylene-C film was realized with length L TVS at 6.29 mm, 7.35 mm and 8.02 mm. The results showed that the micro-plasma jet with an L TVS of 7.35 mm had the minimum applied voltage of 12.7 kV and the minimum micro-etching diameter of 45 μm with the deepest etching depth of 2.8 μm.

  6. A parallel hybrid numerical algorithm for simulating gas flow and gas discharge of an atmospheric-pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Lin, K.-M.; Hu, M.-H.; Hung, C.-T.; Wu, J.-S.; Hwang, F.-N.; Chen, Y.-S.; Cheng, G.

    2012-12-01

    Development of a hybrid numerical algorithm which couples weakly with the gas flow model (GFM) and the plasma fluid model (PFM) for simulating an atmospheric-pressure plasma jet (APPJ) and its acceleration by two approaches is presented. The weak coupling between gas flow and discharge is introduced by transferring between the results obtained from the steady-state solution of the GFM and cycle-averaged solution of the PFM respectively. Approaches of reducing the overall runtime include parallel computing of the GFM and the PFM solvers, and employing a temporal multi-scale method (TMSM) for PFM. Parallel computing of both solvers is realized using the domain decomposition method with the message passing interface (MPI) on distributed-memory machines. The TMSM considers only chemical reactions by ignoring the transport terms when integrating temporally the continuity equations of heavy species at each time step, and then the transport terms are restored only at an interval of time marching steps. The total reduction of runtime is 47% by applying the TMSM to the APPJ example presented in this study. Application of the proposed hybrid algorithm is demonstrated by simulating a parallel-plate helium APPJ impinging onto a substrate, which the cycle-averaged properties of the 200th cycle are presented. The distribution patterns of species densities are strongly correlated by the background gas flow pattern, which shows that consideration of gas flow in APPJ simulations is critical.

  7. Plasma jet ignition device

    DOEpatents

    McIlwain, Michael E.; Grant, Jonathan F.; Golenko, Zsolt; Wittstein, Alan D.

    1985-01-15

    An ignition device of the plasma jet type is disclosed. The device has a cylindrical cavity formed in insulating material with an electrode at one end. The other end of the cylindrical cavity is closed by a metal plate with a small orifice in the center which plate serves as a second electrode. An arc jumping between the first electrode and the orifice plate causes the formation of a highly-ionized plasma in the cavity which is ejected through the orifice into the engine cylinder area to ignite the main fuel mixture. Two improvements are disclosed to enhance the operation of the device and the length of the plasma plume. One improvement is a metal hydride ring which is inserted in the cavity next to the first electrode. During operation, the high temperature in the cavity and the highly excited nature of the plasma breaks down the metal hydride, liberating hydrogen which acts as an additional fuel to help plasma formation. A second improvement consists of a cavity insert containing a plurality of spaced, metal rings. The rings act as secondary spark gap electrodes reducing the voltage needed to maintain the initial arc in the cavity.

  8. Ambient air particle transport into the effluent of a cold atmospheric-pressure argon plasma jet investigated by molecular beam mass spectrometry

    NASA Astrophysics Data System (ADS)

    Dünnbier, M.; Schmidt-Bleker, A.; Winter, J.; Wolfram, M.; Hippler, R.; Weltmann, K.-D.; Reuter, S.

    2013-10-01

    Ambient air species, which are transported into the active effluent of an atmospheric-pressure plasma jet result in highly reactive oxygen and nitrogen species (RONS). Especially for the envisaged application field of plasma medicine, these RONS are responsible for strong biological responses. In this work, the effect of ambient air transport into the effluent of an atmospheric-pressure plasma argon jet on the on-axis densities of nitrogen, oxygen and argon was investigated by means of absolutely calibrated molecular beam mass spectrometry (MBMS). According to biomedical experiments a (bottomless) Petri dish was installed in front of the MBMS. In the following, the near flow field is referring to the region close to the nozzle exit and the far flow field is referring to the region beyond that. The absolute on-axis densities were obtained by three different methods, for the near flow field with VUV-absorption technique, for the far flow field with the MBMS and the total flow field was calculated with a computational fluid dynamics (CFD) simulation. The results of the ambient air particle densities of all independent methods were compared and showed an excellent agreement. Therefore the transport processes of ambient air species can be measured for the whole effluent of an atmospheric-pressure plasma jet. Additionally, with the validation of the simulation it is possible in future to calculate the ambient species transport for various gas fluxes in the same turbulent flow regime. Comparing the on-axis densities obtained with an ignited and with a non-ignited plasma jet shows that for the investigated parameters, the main influence on the ambient air species transport is due to the increased temperature in the case when the jet is switched on. Moreover, the presence of positive ions (e.g. ArN_{2}^{+} ) formed due to the interaction of plasma-produced particles and ambient air species, which are transported into the effluent, is shown.

  9. Observation of inactivation of Bacillus sbtilis spores under exposures of oxygen added argon atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Shen, Jie; Cheng, Cheng; Zhao, Ying; Xiao, Dezhi; Lan, Yan; Xie, Hongbing; Cheng, Junli; Meng, Yuedong; Li, Jiangang; Chu, Paul K.

    2014-11-01

    The inactivation of Bacillus subtilis spores by an Ar plasma jet mixed with different amounts of oxygen is reported. 5.8 × 106 B. subtilis spores are sterilized by an Ar/O2 (8.7%) plasma jet after exposure for 2 min. The densities of ozone and oxygen radicals in the Ar/O2 plasma jet increase with oxygen concentration and are estimated by optical spectroscopy diagnostic. The malondialdehyde (MDA) test shows that oxygen radicals participate in bacterial inactivation. Scanning electron microscopy (SEM) reveals the deformation of the spore shape due to etching by oxygen radicals and the dependence of the degree of deformation on the density of oxygen radicals.

  10. Study of OH radical generation in atmospheric pressure microwave plasma jets of Ar, N2 and O2 gases using pulsed cavity ringdown spectroscopy

    NASA Astrophysics Data System (ADS)

    Wang, Chuji; Srivastava, Nimisha

    2009-11-01

    We employ UV-pulsed laser cavity ringdown spectroscopy, optical emission spectroscopy and visual imaging, to characterize OH radical generation in atmospheric pressure microwave plasma jets created, respectively, by argon, mixture of Ar and N2, mixture of Ar and O2, and mixture of Ar, N2 and O2. OH radicals were observed in far downstream for all of these plasma jets (Far downstream is referred to as the location where ratio of the distance from the jet orifice to the length of the jet column is > 3).We also investigated the effect of variations in humidity on OH generation in the APJs. Absolute number densities were measured for OH (v'' = 0, J''= 3.5) along the plasma column axis. Effects on OH radical concentrations along the plasma column axis with variations of plasma powers, gas flow rates with different mixing ratios and humidity levels were also studied. The rotational Trot, vibrational Tvib and electronic excitation temperature Telex were provided by simulations of emission spectra of the plasmas.

  11. Atomic oxygen TALIF measurements in an atmospheric-pressure microwave plasma jet with in situ xenon calibration

    NASA Astrophysics Data System (ADS)

    van Gessel, A. F. H.; van Grootel, S. C.; Bruggeman, P. J.

    2013-10-01

    Two-photon absorption laser-induced fluorescence (TALIF) is used to measure the absolute density of atomic oxygen (O) in a coaxial microwave jet in ambient air at atmospheric pressure, operated with a mixture of He and a few per cent of air. The TALIF signal is calibrated using a gas mixture containing Xe. A novel method to perform calibration in situ, at atmospheric pressure, is introduced. The branching ratios of several Xe mixtures are reported, to enable us to perform the Xe calibration without the need for a vacuum vessel. The O densities are measured spatially resolved, and as a function of admixed air to the He, and microwave power. The electron density and temperatures are measured using Thomson scattering, and the N2 and O2 densities are measured using Raman scattering. O densities are found to have a maximum of (4-6) × 1022 m-3, which indicate that O2 is close to fully dissociated in the plasma. This is confirmed by the Raman scattering measurements. O is found to recombine mainly into species other than O2 in the afterglow, which is suggested to consist of O3 and oxidized components of NO.

  12. The Role of Helium Metastable States in Radio-Frequency Helium-Oxygen Atmospheric Pressure Plasma Jets: Measurement and Numerical Simulation

    NASA Astrophysics Data System (ADS)

    Niemi, Kari; Waskoenig, Jochen; Sadeghi, Nader; Gans, Timo; O'Connell, Deborah

    2011-10-01

    Absolute densities of metastable He atoms were measured line-of sight integrated along the plasma channel of a capacitively-coupled radio-frequency driven atmospheric pressure plasma jet operated in helium oxygen mixtures by tunable diode-laser absorption spectroscopy. Dependencies of the He metastable density with oxygen admixtures up to 1 percent were investigated. Results are compared to a 1-d numerical simulation, which includes a semi-kinetical treatment of the electron dynamics and the complex plasma chemistry (20 species, 184 reactions), and very good agreement is found. The main formation mechanisms for the helium metastables are identified and analyzed, including their pronounced spatio-temporal dynamics. Penning ionization through helium metastables is found to be significant for plasma sustainment, while it is revealed that helium metastables are not an important energy carrying species into the jet effluent and therefore will not play a direct role in remote surface treatments.

  13. Novel thin films deposited on electrospun PCL scaffolds by atmospheric pressure plasma jet for L929 fibroblast cell cultivation

    NASA Astrophysics Data System (ADS)

    Gozutok, M.; Baitukha, A.; Arefi-Khonsari, F.; Turkoglu Sasmazel, H.

    2016-11-01

    This paper reports on the deposition of PCL homopolymers and poly ɛ-caprolactone-polyethylene glycol (PCL-PEG) copolymers by atmospheric pressure plasma jet (APPJ) onto electrospun PCL scaffolds for improving L929 fibroblast cell growth. Polymer deposited scaffolds showed better stability as well as lower CA as compared to those treated with APPJ in Ar alone used as the carrier gas to introduce the precursors due to the formation of polar groups generated during the plasma treatment, such as -OH and/or -COO. Average fiber and porosity sizes were calculated by using SEM photographs and the ImageJ Launcher Software program and higher values were observed for both PCL and PCL-PEG deposited scaffolds than the untreated electrospun PCL scaffolds. XPS analysis showed that C1s% content decreased for PCL deposited (from 82.4% to 71.0%) and PCL-PEG deposited (from 82.4% to 57.7%) and O1s% composition increased for PCL deposited (from 17.6% to 29.0%) and PCL-PEG deposited (from 17.6% to 42.3%) compared to the untreated one. XPS results proved more incorporation of oxygen moieties on the deposited surfaces than the untreated samples giving rise to more hydrophilic surfaces to the deposited ones. Standard in vitro MTT test, Giemsa staining, fluorescence and CLSM imaging techniques were used for the determination of cell viability, adhesion and proliferation. Cell culture experiments showed that PCL-PEG deposited electrospun PCL scaffolds had the most promising cell adhesion, proliferation and growth among the treated scaffolds. The increased average fiber diameter caused by deposition as well as oxygen containing polar groups formed on the surfaces due to the radicals present in the plasma atmosphere provided higher surface area and functionality, respectively, for cells to attach, yielding better biocompatibility performance.

  14. Verification of the plasma diffusion-wave propagation in an atmospheric-pressure plasma jet with the solution of a diffusion equation

    NASA Astrophysics Data System (ADS)

    Cho, Guangsup; Uhm, Han Sup

    2016-10-01

    The time-dependent solution of diffusion equation by the Fourier integration provides the axial diffusion velocity of a plasma packet, which is a key element of the plasma propagation in a plasma jet operated by the several tens of kHz. The plasma diffusion velocity is higher than the order of un ˜ 10 m/s at a high electric-field region of plasma generation and it is about the order of un ˜ 10 m/s at the plasma column of a low field region in a jet-nozzle inside. Meanwhile, the diffusion velocity is slower than the order of un ˜ 10 m/s in the open-air space where the plasma density flattens due to its radial expansion. Using these diffusion velocity data, the group-velocity of plasma diffusion wave-packet is given by ug ˜ cs2/un, a combination of the diffusion velocity un and the acoustic velocity cs. The experimental results of the plasma propagation can be verified with the plasma propagation in a form of the wave-packet whose propagation velocity is 104 m/s in a tube inside and is as fast as 105 m/s in the open-air space, thereby reconfirming that the theory of a plasma diffusion-wave is the origin of the plasma propagation in a plasma jet.

  15. Rapid atmospheric pressure plasma jet processed reduced graphene oxide counter electrodes for dye-sensitized solar cells.

    PubMed

    Liu, Hsiao-Wei; Liang, Sheng-Ping; Wu, Ting-Jui; Chang, Haoming; Kao, Peng-Kai; Hsu, Cheng-Che; Chen, Jian-Zhang; Chou, Pi-Tai; Cheng, I-Chun

    2014-09-10

    In this work, we present the use of reduced graphene oxide (rGO) as the counter electrode materials in dye-sensitized solar cells (DSSCs). rGO was first deposited on a fluorine-doped tin oxide glass substrate by screen-printing, followed by post-treatment to remove excessive organic additives. We investigated the effect of atmospheric pressure plasma jet (APPJ) treatment on the DSSC performance. A power conversion efficiency of 5.19% was reached when DSSCs with an rGO counter electrode were treated by APPJs in the ambient air for a few seconds. For comparison, it requires a conventional calcination process at 400 °C for 15 min to obtain comparable efficiency. Scanning electron micrographs show that the APPJ treatment modifies the rGO structure, which may reduce its conductivity in part but simultaneously greatly enhances its catalytic activity. Combined with the rapid removal of organic additives by the highly reactive APPJ, DSSCs with APPJ-treated rGO counter electrode show comparable efficiencies to furnace-calcined rGO counter electrodes with greatly reduced process time. This ultrashort process time renders an estimated energy consumption per unit area of 1.1 kJ/cm(2), which is only one-third of that consumed in a conventional furnace calcination process. This new methodology thus saves energy, cost, and time, which is greatly beneficial to future mass production.

  16. The effect of three different methods of adding O2 additive on O concentration of atmospheric pressure plasma jets (APPJs)

    NASA Astrophysics Data System (ADS)

    Yue, Y.; Xian, Y.; Pei, X.; Lu, X.

    2016-12-01

    In order to maximize the O concentration generated by the atmospheric pressure plasma jets (APPJs), several different methods of adding O2 additive to working gas have been proposed. However, it is not clear, which method is capable of generating the highest concentration of O atom. In this paper, the concentration of O atoms in an APPJs by adding O2 to (1) the working gas, to (2) the downstream inside the tube, and (3) to the shielding gas is investigated by two-photon absorption laser-induced fluorescence spectrometry. The results clearly demonstrate that the highest O density is achieved when 1.5% of O2 is added to the working gas rather than the other two methods. In other words, the most effective way to generate O atoms is by premixing O2 with the working gas. Further investigation suggests that O atoms are mainly generated around the electrode region, where the electric field is highest. In addition, when O2 is added to the working gas, if in the meantime extra O2 is added to the downstream inside the tube, a significant decrease of O density is observed.

  17. Feasibility study of surface-modified carbon cloth electrodes using atmospheric pressure plasma jets for microbial fuel cells

    NASA Astrophysics Data System (ADS)

    Chang, Shih-Hang; Liou, Jyun-Sian; Liu, Jung-Liang; Chiu, Yi-Fan; Xu, Chang-Han; Chen, Bor-Yann; Chen, Jian-Zhang

    2016-12-01

    This study investigated the surface and electrochemical properties of carbon cloth electrodes surface-modified by using atmospheric pressure plasma jets (APPJs) for applications involving microbial fuel cells (MFCs). APPJ treatment made the carbon cloth highly hydrophilic and did not introduce any observable cracks or flaws. MFCs configured with APPJ-treated carbon cloth electrodes exhibited electrochemical performance (maximum power density of 7.56 mW m-2) superior to that of MFCs configured with untreated carbon cloth electrodes (maximum power density of 2.38 mW m-2). This boost in performance can be attributed to the formation of abundant carboxyl and ammonium functional groups on the surface of APPJ-treated carbon cloth, which promoted the formation of anodic biofilms and the adhesion of bacteria, while facilitating the transfer of electrons from the bacteria to the electrodes. APPJ surface modification is non-toxic and environmentally friendly (no exogenous chemicals are required), which is particularly beneficial as the introduction of toxins might otherwise inhibit bacterial growth and metabolism. The APPJ surface modification process is rapid, cost-effective, and applicable to substrates covering a large area, making it ideal for the fabrication of large-scale MFCs and bioelectrochemical bioenergy devices.

  18. Highly efficient photocatalytic TiO2 coatings deposited by open air atmospheric pressure plasma jet with aerosolized TTIP precursor

    NASA Astrophysics Data System (ADS)

    Fakhouri, H.; Ben Salem, D.; Carton, O.; Pulpytel, J.; Arefi-Khonsari, F.

    2014-07-01

    A simple method to deposit photocatalytic TiO2 coatings, at a high rate (20-40 µm s-1), and with a high porosity, is reported in this paper. This method, which allows the treatment of membranes (with an 800 nm pore size), is based on the introduction of a liquid precursor sprayed into an open-air atmospheric pressure plasma jet (APPJ). The photocatalytic activity of the TiO2 thin films prepared by APPJ have been compared with our best N-doped TiO2 thin films, deposited by reactive radio frequency (RF) magnetron sputtering, previously reported in the literature. The morphology, chemical composition, photoelectrochemical, and photocatalytic properties of the coatings have been studied in this paper. Significant control of the porosity and crystallinity was achieved by varying the deposition parameters and the annealing temperature. Under optimized conditions, the TiO2 coatings deposited by APPJ are characterized by a higher photocatalytic activity as compared to the optimized thin films deposited by RF sputtering. This difference can be explained by the higher specific surface of the APPJ coatings. Finally, the most interesting characteristic of this APPJ-liquid spray process is its capacity to treat membranes without blocking the pores, and to produce photocatalytic membranes which can efficiently combine filtration and photocatalysis for water treatment.

  19. Effects of metastable species in helium and argon atmospheric pressure plasma jets (APPJs) on inactivation of periodontopathogenic bacteria

    NASA Astrophysics Data System (ADS)

    Yoon, Sung-Young; Kim, Kyoung-Hwa; Seol, Yang-Jo; Kim, Su-Jeong; Bae, Byeongjun; Huh, Sung-Ryul; Kim, Gon-Ho

    2016-05-01

    The helium and argon have been widely used as discharge gases in atmospheric pressure plasma jets (APPJs) for bacteria inactivation. The APPJs show apparent different in bullet propagation speed and bacteria inactivation rate apparently vary with discharge gas species. This work shows that these two distinctive features of APPJs can be linked through one factor, the metastable energy level. The effects of helium and argon metastable species on APPJ discharge mechanism for reactive oxygen nitrogen species (RONS) generation in APPJs are investigated by experiments and numerical estimation. The discharge mechanism is investigated by using the bullet velocity from the electric field which is obtained with laser induced fluorescence (LIF) measurement. The measured electric field also applied on the estimation of RONS generation, as electron energy source term in numerical particle reaction. The estimated RONS number is verified by comparing NO and OH densities to the inactivation rate of periodontitis bacteria. The characteristic time for bacteria inactivation of the helium-APPJ was found to be 1.63 min., which is significantly less than that of the argon-APPJ, 12.1 min. In argon-APPJ, the argon metastable preserve the energy due to the lack of the Penning ionization. Thus the surface temperature increase is significantly higher than helium-APPJ case. It implies that the metastable energy plays important role in both of APPJ bullet propagation and bacteria inactivation mechanism.

  20. Development of hydrophilic dental wax without surfactant using a non-thermal air atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Lee, Jung-Hwan; Kim, Yong-Hee; Choi, Eun-Ha; Kim, Kwang-Mahn; Kim, Kyoung-Nam

    2014-06-01

    Dental wax (DW), a low-melting and high-molecular-weight organic mixture, is widely used in dentistry for forming moulds of teeth. Hydrophilicity is an important property for DW, as a wet dental investment is used to surround the wax before wax burnout is performed. However, recent attempts to improve the hydrophilicity of DW using a surfactant have resulted in the reduced mechanical properties of the dental investment, leading to the failure of the dental restoration. This study applied a non-thermal air atmospheric pressure plasma jet (AAPPJ) for DW surface treatment and investigated its effect on both DW hydrophilicity and the dental investment's mechanical properties. The results showed that the application of the AAPPJ significantly improved the hydrophilicity of the DW, and that the results were similar to that of cleaner-treated DW using commercially available products with surfactant. A surface chemical analysis indicated that the improvement of hydrophilicity was related to an increase in the number of oxygen-related bonds on the DW surface following the removal of carbon hydrate in both AAPPJ and cleaner-treated DW. However, cleaner treatment compromised the mechanical property of the dental investment when the dental investment was in contact with the treated DW, while the AAPPJ treatment did not. Therefore, the use of AAPPJ to treat DW is a promising method for accurate dental restoration, as it induces an improvement in hydrophilicity without harming the dental investment.

  1. Evaluation of extra- and intracellular OH radical generation, cancer cell injury, and apoptosis induced by a non-thermal atmospheric-pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Ninomiya, Kazuaki; Ishijima, Tatsuo; Imamura, Masatoshi; Yamahara, Takayuki; Enomoto, Hiroshi; Takahashi, Kenji; Tanaka, Yasunori; Uesugi, Yoshihiko; Shimizu, Nobuaki

    2013-10-01

    In this study, we investigated the effects of a non-thermal atmospheric-pressure plasma jet inducing extracellular and intracellular OH radical generation as well as cell injury and apoptosis for the cultured human breast cancer cells. Increased OH radical generation in the extracellular culture medium (liquid phase) was observed with increased irradiation time, distance to the liquid surface, and voltage. From the voltage-response relationships for two breast cancer cell lines (invasive MDA-MB-231 cells and non-invasive MCF-7 cells) and normal breast cells (HMEC), the half-maximal effective peak-to-peak voltage (EV50) values were 16.7 ± 0.3 kV, 15.0 ± 0.4 kV and 11.2 ± 0.7 kV for MDA-MB-231, MCF-7 and HMEC cells, respectively. This indicated that there was almost no selective cancer cell injury induced by plasma jet irradiation under these conditions. Compared with control condition without a plasma jet, intracellular OH radical accumulation and apoptotic cells were observed with a plasma jet using conditions that induced injury to 50% of cells irrespective of the cancer cell line.

  2. Absolute atomic oxygen density measurements for nanosecond-pulsed atmospheric-pressure plasma jets using two-photon absorption laser-induced fluorescence spectroscopy

    NASA Astrophysics Data System (ADS)

    Jiang, C.; Carter, C.

    2014-12-01

    Nanosecond-pulsed plasma jets that are generated under ambient air conditions and free from confinement of electrodes have become of great interest in recent years due to their promising applications in medicine and dentistry. Reactive oxygen species that are generated by nanosecond-pulsed, room-temperature non-equilibrium He-O2 plasma jets among others are believed to play an important role during the bactericidal or sterilization processes. We report here absolute measurements of atomic oxygen density in a 1 mm-diameter He/(1%)O2 plasma jet at atmospheric pressure using two-photon absorption laser-induced fluorescence spectroscopy. Oxygen number density on the order of 1013 cm-3 was obtained in a 150 ns, 6 kV single-pulsed plasma jet for an axial distance up to 5 mm above the device nozzle. Temporally resolved O density measurements showed that there are two maxima, separated in time by 60-70 µs, and a total pulse duration of 260-300 µs. Electrostatic modeling indicated that there are high-electric-field regions near the nozzle exit that may be responsible for the observed temporal behavior of the O production. Both the field-distribution-based estimation of the time interval for the O number density profile and a pulse-energy-dependence study confirmed that electric-field-dependent, direct and indirect electron-induced processes play important roles for O production.

  3. The interaction of atmospheric pressure plasma jets with cancer and normal cells: generation of intracellular reactive oxygen species and changes of the cell proliferation and cell cycle

    NASA Astrophysics Data System (ADS)

    Chung, Tae Hun; Joh, Hea Min; Kim, Sun Ja; Leem, Sun Hee

    2013-09-01

    The possibility of atmospheric pressure plasmas is emerging as a candidate in cancer therapy. The primary role is played by reactive oxygen species (ROS), UV photons, charged particles and electric fields. Among them, intracellular ROS induced by plasma are considered to be the key constituents that induce cellular changes and apoptosis. In this study, the effects of atmospheric pressure plasma jet on cancer cells (human lung carcinoma cells) and normal cells (embryonic kidney cells and bronchial epithelial cells) were investigated. The plasma treatment was performed under different working gases, applied voltages, gas flow rates, and with and without additive oxygen flow. Using a detection dye, we observed that plasma exposure leads to the increase of the intracellular ROS and that the intracellular ROS production can be controlled by plasma parameters. A significant ROS generation was induced by plasma exposure on cancer cells and the overproduction of ROS contributes to the reduced cell proliferation. Normal cells were observed to be less affected by the plasma-mediated ROS and cell proliferation was less changed. The plasma treatment also resulted in the alteration of the cell cycle that contributes to the induction of apoptosis in cancer cells. The selective effect on cancer and normal cells provides a promising prospect of cold plasma as cancer therapy. This work was supported by the National Research Foundation of Korea under Contract No. 2012R1A1A2002591 and 2012R1A1A3010213.

  4. Flux of OH and O radicals onto a surface by an atmospheric-pressure helium plasma jet measured by laser-induced fluorescence

    NASA Astrophysics Data System (ADS)

    Yonemori, Seiya; Ono, Ryo

    2014-03-01

    The atmospheric-pressure helium plasma jet is of emerging interest as a cutting-edge biomedical device for cancer treatment, wound healing and sterilization. Reactive oxygen species such as OH and O radicals are considered to be major factors in the application of biological plasma. In this study, density distribution, temporal behaviour and flux of OH and O radicals on a surface are measured using laser-induced fluorescence. A helium plasma jet is generated by applying pulsed high voltage of 8 kV with 10 kHz using a quartz tube with an inner diameter of 4 mm. To evaluate the relation between the surface condition and active species production, three surfaces are used: dry, wet and rat skin. When the helium flow rate is 1.5 l min-1, radial distribution of OH density on the rat skin surface shows a maximum density of 1.2 × 1013 cm-3 at the centre of the plasma-mediated area, while O atom density shows a maximum of 1.0 × 1015 cm-3 at 2.0 mm radius from the centre of the plasma-mediated area. Their densities in the effluent of the plasma jet are almost constant during the intervals of the discharge pulses because their lifetimes are longer than the pulse interval. Their density distribution depends on the helium flow rate and the surface humidity. With these results, OH and O production mechanisms in the plasma jet and their flux onto the surface are discussed.

  5. Voltage and Pressure Scaling of Streamer Dynamics in a Helium Plasma Jet With N2 CO-Flow (Postprint)

    DTIC Science & Technology

    2014-08-14

    of measurements since it allowed us to measure streamer scaling properties over a wide voltage range with- out surface flashover in our configuration...allows the formation of a non-stochastic active discharge extending beyond the anodic electrode uses a capillary dielectric tube with helium gas flow...of discharge behaves like a cath- ode directed streamer propagation. This plasma jet uses a dielectric barrier configuration with annular anode

  6. Acquisition of cell-adhesion capability of the surface of crosslinked albumin films irradiated with atmospheric-pressure plasma jets

    NASA Astrophysics Data System (ADS)

    Shirafuji, Tatsuru; Iwamura, Mami; Taga, Ryosuke; Kashiwagi, Yukiyasu; Nakajima, Kota; Ogata, Yuji; Tanaka, Kenji; Tachibana, Akira; Tanabe, Toshizumi

    2016-07-01

    Crosslinked albumin films, to which L929 cells do not attach by nature, acquire the L929-cell-adhesion capability by irradiation of an atmospheric-pressure plasma jet (APPJ) of He gas. The number of attached cells was 2.6 × 104 cells/cm2 after the APPJ irradiation for 180 s, while conventional UV photolithography, which was performed in our previous work, required 2 h to obtain the same order of magnitude of the number of attached cells. The contact angle of samples decreased steeply from 105 to 38° in the first 10 s irradiation, but decreased quite gradually from 38 to 32° with increasing irradiation time from 10 to 180 s. In contrast to the nonlinear variation in the contact angles, the number of attached cells almost linearly increased from 4.5 × 103 to 2.6 × 104 cells/cm2 with increasing treatment time. X-ray photoelectron spectroscopy of the samples indicated that hydrophilic functional groups of C-C=O gradually formed with increasing APPJ irradiation time up to 180 s. These results suggest that the cell-adhesion capability of the crosslinked albumin films is not simply explained by the decrease in contact angle but also by the formation of oxidized functional groups on the surface. The effects of UV and vacuum UV light from APPJ were negligible, which indicates that the formation of oxidized functional groups on the surface is not caused by photon-assisted surface reactions but by reactions involving chemically active species supplied from APPJ.

  7. Portable nanosecond pulsed air plasma jet

    SciTech Connect

    Walsh, J. L.; Kong, M. G.

    2011-08-22

    Low-temperature atmospheric pressure plasmas are of great importance in many emerging biomedical and materials processing applications. The redundancy of a vacuum system opens the gateway for highly portable plasma systems, for which air ideally becomes the plasma-forming gas and remote plasma processing is preferred to ensure electrical safety. Typically, the gas temperature observed in air plasma greatly exceeds that suitable for the processing of thermally liable materials; a large plasma-sample distance offers a potential solution but suffers from a diluted downstream plasma chemistry. This Letter reports a highly portable air plasma jet system which delivers enhanced downstream chemistry without compromising the low temperature nature of the discharge, thus forming the basis of a powerful tool for emerging mobile plasma applications.

  8. Mechanism and comparison of needle-type non-thermal direct and indirect atmospheric pressure plasma jets on the degradation of dyes

    PubMed Central

    Attri, Pankaj; Yusupov, Maksudbek; Park, Ji Hoon; Lingamdinne, Lakshmi Prasanna; Koduru, Janardhan Reddy; Shiratani, Masaharu; Choi, Eun Ha; Bogaerts, Annemie

    2016-01-01

    Purified water supply for human use, agriculture and industry is the major global priority nowadays. The advanced oxidation process based on atmospheric pressure non-thermal plasma (NTP) has been used for purification of wastewater, although the underlying mechanisms of degradation of organic pollutants are still unknown. In this study we employ two needle-type atmospheric pressure non-thermal plasma jets, i.e., indirect (ID-APPJ) and direct (D-APPJ) jets operating at Ar feed gas, for the treatment of methylene blue, methyl orange and congo red dyes, for two different times (i.e., 20 min and 30 min). Specifically, we study the decolorization/degradation of all three dyes using the above mentioned plasma sources, by means of UV-Vis spectroscopy, HPLC and a density meter. We also employ mass spectroscopy to verify whether only decolorization or also degradation takes place after treatment of the dyes by the NTP jets. Additionally, we analyze the interaction of OH radicals with all three dyes using reactive molecular dynamics simulations, based on the density functional-tight binding method. This investigation represents the first report on the degradation of these three different dyes by two types of NTP setups, analyzed by various methods, and based on both experimental and computational studies. PMID:27708352

  9. Mechanism and comparison of needle-type non-thermal direct and indirect atmospheric pressure plasma jets on the degradation of dyes

    NASA Astrophysics Data System (ADS)

    Attri, Pankaj; Yusupov, Maksudbek; Park, Ji Hoon; Lingamdinne, Lakshmi Prasanna; Koduru, Janardhan Reddy; Shiratani, Masaharu; Choi, Eun Ha; Bogaerts, Annemie

    2016-10-01

    Purified water supply for human use, agriculture and industry is the major global priority nowadays. The advanced oxidation process based on atmospheric pressure non-thermal plasma (NTP) has been used for purification of wastewater, although the underlying mechanisms of degradation of organic pollutants are still unknown. In this study we employ two needle-type atmospheric pressure non-thermal plasma jets, i.e., indirect (ID-APPJ) and direct (D-APPJ) jets operating at Ar feed gas, for the treatment of methylene blue, methyl orange and congo red dyes, for two different times (i.e., 20 min and 30 min). Specifically, we study the decolorization/degradation of all three dyes using the above mentioned plasma sources, by means of UV-Vis spectroscopy, HPLC and a density meter. We also employ mass spectroscopy to verify whether only decolorization or also degradation takes place after treatment of the dyes by the NTP jets. Additionally, we analyze the interaction of OH radicals with all three dyes using reactive molecular dynamics simulations, based on the density functional-tight binding method. This investigation represents the first report on the degradation of these three different dyes by two types of NTP setups, analyzed by various methods, and based on both experimental and computational studies.

  10. Mechanism and comparison of needle-type non-thermal direct and indirect atmospheric pressure plasma jets on the degradation of dyes.

    PubMed

    Attri, Pankaj; Yusupov, Maksudbek; Park, Ji Hoon; Lingamdinne, Lakshmi Prasanna; Koduru, Janardhan Reddy; Shiratani, Masaharu; Choi, Eun Ha; Bogaerts, Annemie

    2016-10-06

    Purified water supply for human use, agriculture and industry is the major global priority nowadays. The advanced oxidation process based on atmospheric pressure non-thermal plasma (NTP) has been used for purification of wastewater, although the underlying mechanisms of degradation of organic pollutants are still unknown. In this study we employ two needle-type atmospheric pressure non-thermal plasma jets, i.e., indirect (ID-APPJ) and direct (D-APPJ) jets operating at Ar feed gas, for the treatment of methylene blue, methyl orange and congo red dyes, for two different times (i.e., 20 min and 30 min). Specifically, we study the decolorization/degradation of all three dyes using the above mentioned plasma sources, by means of UV-Vis spectroscopy, HPLC and a density meter. We also employ mass spectroscopy to verify whether only decolorization or also degradation takes place after treatment of the dyes by the NTP jets. Additionally, we analyze the interaction of OH radicals with all three dyes using reactive molecular dynamics simulations, based on the density functional-tight binding method. This investigation represents the first report on the degradation of these three different dyes by two types of NTP setups, analyzed by various methods, and based on both experimental and computational studies.

  11. Radical reaction in aqueous media injected by atmospheric pressure plasma jet and protective effect of antioxidant reagents evaluated by single-molecule DNA measurement

    NASA Astrophysics Data System (ADS)

    Kurita, Hirofumi; Shimizu, Mika; Sano, Kaori; Nakajima, Tomoko; Yasuda, Hachiro; Takashima, Kazunori; Mizuno, Akira

    2014-01-01

    Nonthermal atmospheric pressure plasma (NTP) has been extensively studied for biological and medical applications in recent years. Chemically active species are generated and injected into aqueous media subjected to plasma exposure. They play an important role in the activation and/or inactivation of biomolecules, such as nucleic acids, lipid, and proteins, in aqueous media. To evaluate the effect of NTP on these biomolecules at the molecular level, we have been considering large DNA molecules to be used as a biomarker. The single-molecule-based analysis of strand breakages induced by NTP, namely, the atmospheric pressure plasma jet (APPJ), on large DNA molecules has been performed. We demonstrated the facile estimation of the rate of double-strand breaks induced by the APPJ. Using this analysis, we have evaluated both the intensity of radical reaction and the protective effect on the reaction by adding antioxidant agents.

  12. Generation of reactive oxygen and nitrogen species and its effects on DNA damage in lung cancer cells exposed to atmospheric pressure helium/oxygen plasma jets

    NASA Astrophysics Data System (ADS)

    Chung, Tae Hun; Joh, Hea Min; Kim, Sun Ja; Choi, Ji Ye; Kang, Tae-Hong

    2016-09-01

    We investigated the effects of the operating parameters on the generation of reactive oxygen and nitrogen species (RONS) in the gas and liquid phases exposed to atmospheric pressure a pulsed-dc helium plasma jets. The densities of reactive species including OH radicals were obtained at the plasma-liquid surface and inside the plasma-treated liquids using ultraviolet absorption spectroscopy and chemical probe method. And the nitrite concentration was detected by Griess assay. The data are very suggestive that there is a strong correlation among the production of RONS in the plasmas and liquids. Exposure of plasma to cancer cells increases the cellular levels of RONS, which has been linked to apoptosis and the damage of cellular proteins, and may also indirectly cause structural damage to DNA. To identify the correlation between the production of RONS in cells and plasmas, various assay analyses were performed on plasma treated human lung cancer cells (A549) cells. In addition, the effect of additive oxygen gas on the plasma-induced oxidative stress in cancer cells was investigated. It was observed that DNA damage was significantly increased with helium/oxygen plasma compared to with pure helium plasma.

  13. Two-dimensional concentration distribution of reactive oxygen species transported through a tissue phantom by atmospheric-pressure plasma-jet irradiation

    NASA Astrophysics Data System (ADS)

    Kawasaki, Toshiyuki; Sato, Akihiro; Kusumegi, Shota; Kudo, Akihiro; Sakanoshita, Tomohiro; Tsurumaru, Takuya; Uchida, Giichiro; Koga, Kazunori; Shiratani, Masaharu

    2016-07-01

    The two-dimensional concentration distribution of reactive oxygen species (ROSs) transported through an agarose-film tissue phantom by atmospheric-pressure plasma-jet irradiation is visualized using a KI-starch gel reagent. Oxygen addition to helium enhances ROS transportation through the film. A radial ROS distribution pattern at the plasma-irradiated film surface changes into a doughnut-shaped pattern after passing through the film. The ROS transportation speed is 0.14-0.2 mm/min. We suggest that there are two types of ROS transportation pathways in the plasma-irradiated film: linear and circular. The majority of ROSs are transported through the circular pathway. ROS concentration distributions changed markedly with irradiation distance. Diffusive ROS transportation due to a concentration gradient is negligible in plasma-irradiated films.

  14. Maskless localized patterning of biomolecules on carbon nanotube microarray functionalized by ultrafine atmospheric pressure plasma jet using biotin-avidin system

    NASA Astrophysics Data System (ADS)

    Abuzairi, Tomy; Okada, Mitsuru; Purnamaningsih, Retno Wigajatri; Poespawati, Nji Raden; Iwata, Futoshi; Nagatsu, Masaaki

    2016-07-01

    Ultrafine plasma jet is a promising technology with great potential for nano- or micro-scale surface modification. In this letter, we demonstrated the use of ultrafine atmospheric pressure plasma jet (APPJ) for patterning bio-immobilization on vertically aligned carbon nanotube (CNT) microarray platform without a physical mask. The biotin-avidin system was utilized to demonstrate localized biomolecule patterning on the biosensor devices. Using ±7.5 kV square-wave pulses, the optimum condition of plasma jet with He/NH3 gas mixture and 2.5 s treatment period has been obtained to functionalize CNTs. The functionalized CNTs were covalently linked to biotin, bovine serum albumin (BSA), and avidin-(fluorescein isothiocyanate) FITC, sequentially. BSA was necessary as a blocking agent to protect the untreated CNTs from avidin adsorption. The localized patterning results have been evaluated from avidin-FITC fluorescence signals analyzed using a fluorescence microscope. The patterning of biomolecules on the CNT microarray platform using ultrafine APPJ provides a means for potential application of microarray biosensors based on CNTs.

  15. Plasma Jet Modeling for PLX

    NASA Astrophysics Data System (ADS)

    Mason, Caroline F.; Mason, Rodney J.; Faehl, R. J.; Kirkpatrick, R. C.

    2011-10-01

    The implicit simulation code ePLAS has been applied to plasma jets generated with mini-rail guns for plasma production and compression aimed at use with PLX. The rails are typically planar, 2.5 cm apart and arranged to transport an initial 1 cm or wider vertical plasma fill some 10 cm into a void. The driving magnetic field is 3.2 T. The plasma singly ionized argon at 1017 cm-3. We use ePLAS in both its traditional implicit/hybrid form where it is restricted by an electron Courant time step, and in a new super-hybrid form that extracts the main electron moments from the E&B-field solutions. This provides numerical stability at ion Courant limits, for at least a 10 times larger time step, thus probing microsecond jet dynamics with computational economy. We examine possible field penetration at the cathode and anode gun electrodes. Cathode erosion and EMHD B - Field penetration are possible at lower jet densities. We examine jet transport beyond the gun, modeling possible ionization with either analytic or tabular EOSs. We study the merger of jets with ions represented as either fluids or particles. Work supported by the USDOE under SBIR GRANT DE-SC0004207.

  16. Chemistry of neutral species in the effluent of the micro atmospheric pressure plasma jet in water-helium admixture

    NASA Astrophysics Data System (ADS)

    Willems, Gert; Benedikt, Jan; von Keudell, Achim

    2016-09-01

    A thorough understanding and good control of produced neutral and charged species by cold atmospheric plasmas is essential for potential environmental and/or bio-medical applications. In this study we use the COST reference micro plasma jet (µ-APPJ), which is a radio-frequency capacitive coupled plasma source with 1 mm electrode distance, which has been operated in helium-water vapour mixture and has been studied as a potential source of hydroxyl radicals and hydrogen peroxide molecules. The water vapour concentration was up to 1.2%. Molecular Beam mass spectrometry is used as diagnostic tool. An absolute calibration of hydrogen peroxide was conducted using a double bubbler concept, because the ionization cross section for hydrogen peroxide is not available. Additionally the effluent chemistry was investigated by use of a 0D and 2D model. Absolute densities of hydrogen peroxide and hydroxyl radicals from atmospheric plasma will be presented. Their dependency on water vapour concentration in the carrier gas as well as distance to target have been investigated. The measured density is between 5E-13 cm-3 (2.4ppm) and 1.5E-14 cm-3 (7.2ppm) for both hydrogen peroxide molecules and hydroxyl radicals. The achieved results are in good agreement with other experiments.

  17. The role of helium metastable states in radio-frequency driven helium-oxygen atmospheric pressure plasma jets: measurement and numerical simulation

    NASA Astrophysics Data System (ADS)

    Niemi, K.; Waskoenig, J.; Sadeghi, N.; Gans, T.; O'Connell, D.

    2011-10-01

    Absolute densities of metastable He(23S1) atoms were measured line-of-sight integrated along the discharge channel of a capacitively coupled radio-frequency driven atmospheric pressure plasma jet operated in technologically relevant helium-oxygen mixtures by tunable diode-laser absorption spectroscopy. The dependences of the He(23S1) density in the homogeneous-glow-like α-mode plasma with oxygen admixtures up to 1% were investigated. The results are compared with a one-dimensional numerical simulation, which includes a semi-kinetical treatment of the pronounced electron dynamics and the complex plasma chemistry (in total 20 species and 184 reactions). Very good agreement between measurement and simulation is found. The main formation mechanisms for metastable helium atoms are identified and analyzed, including their pronounced spatio-temporal dynamics. Penning ionization through helium metastables is found to be significant for plasma sustainment, while it is revealed that helium metastables are not an important energy carrying species into the jet effluent and therefore will not play a direct role in remote surface treatments.

  18. Non-invasive probe diagnostic method for electron temperature and ion current density in atmospheric pressure plasma jet source

    SciTech Connect

    Kim, Young-Cheol; Kim, Yu-Sin; Lee, Hyo-Chang; Moon, Jun-Hyeon; Chung, Chin-Wook; Kim, Yunjung; Cho, Guangsup

    2015-08-15

    The electrical probe diagnostics are very hard to be applied to atmospheric plasmas due to severe perturbation by the electrical probes. To overcome this, the probe for measuring electron temperature and ion current density is indirectly contacted with an atmospheric jet source. The plasma parameters are obtained by using floating harmonic analysis. The probe is mounted on the quartz tube that surrounds plasma. When a sinusoidal voltage is applied to a probe contacting on a quartz tube, the electrons near the sheath at dielectric tube are collected and the probe current has harmonic components due to probe sheath nonlinearity. From the relation of the harmonic currents and amplitude of the sheath voltage, the electron temperature near the wall can be obtained with collisional sheath model. The electron temperatures and ion current densities measured at the discharge region are in the ranges of 2.7–3.4 eV and 1.7–5.2 mA/cm{sup 2} at various flow rates and input powers.

  19. Atmospheric Pressure Micro-Thermal-Plasma-Jet Crystallization of Amorphous Silicon Strips for High-Performance Thin Film Transistor Fabrication

    NASA Astrophysics Data System (ADS)

    Morisaki, Seiji; Nakatani, Taichi; Shin, Ryota; Higashi, Seiichiro

    2015-09-01

    Zone melting recrystallization (ZMR) of amorphous silicon (a-Si) strips by micro-thermal-plasma-jet (u-TPJ) irradiation is quite effective to suppress grain boundaries (GBs) except sigma 3 coincidence site lattice (CSL). Intra-grain defects in 1 μm wide strips were significantly reduced by suppressing the agglomeration of molten Si with low temperature condition around melting point of crystalline Si. Thin film transistors (TFTs), using optimized ZMR condition by scanning speed of 1500 mm/s demonstrated extremely high performance with field effect mobility (uFE) of 443 cm2/Vs and swing factor (S) of 210 mV/dec. Part of this work was supported by the Research Institute for Nanodevice and Bio Systems (RNBS), Hiroshima University.

  20. Experiments with laser driven plasma jets

    NASA Astrophysics Data System (ADS)

    Nicolai, Philippe

    2008-04-01

    Laboratory studies can address issues relevant to astrophysics^1 and in some cases improve our understanding of the physical processes that occur in astrophysical objects. So issues related to the jet propagation and collimation over considerable distance and their interactions with surrounding media have begun to be addressed these last years. Laboratory plasmas and astrophysical objects have different length, time and density scales. However, the typical velocities are the same, of a few hundred km/s and the similarity criteria^2 can be applied to scale the laboratory jets to astrophysical conditions. In this presentation, we use a method of jet formation^3 which allows to launch a very fast jet having a velocity around 400 km/s by using a relatively small laser energy, of the order of 100 J. The jet has a Mach number greater than 10, a length of a few mm, and a radius of a few tenths of mm. The interaction of these jets with a gas puff has been recently studied in an experiment carried out at the PALS laser facility. Varying gas pressure and composition, we show that the nature of interaction zone changes from a quasi adiabatic outflow to a strongly radiatively cooling jet. The use of various diagnostics, allows to relate the x-ray emission to the density map of the interaction zone. Already observed in astrophysical objets for strongly different time and space scales, these structures are interpreted in our laboratory experiment by using a semi-analytical model and 2D radiation hydrodynamic simulations. [1] B. Remington et al, Rev. Mod. Phys. 78, 755 (2007) [2] D. Ryutov et al, Phys . Plasmas 8, 1804 (2001) [3] Ph. Nicolai et al, Phys. Plasmas 13, 062701 (2007)

  1. Evaluation of the sensitivity of electro-acoustic measurements for process monitoring and control of an atmospheric pressure plasma jet system

    NASA Astrophysics Data System (ADS)

    Law, V. J.; O'Neill, F. T.; Dowling, D. P.

    2011-06-01

    The development of non-invasive process diagnostic techniques for the control of atmospheric plasmas is a critical issue for the wider adoption of this technology. This paper evaluates the use of a frequency-domain deconvolution of an electro-acoustic emission as a means to monitor and control the plasma formed using an atmospheric pressure plasma jet (APPJ) system. The air plasma system investigated was formed using a PlasmaTreat™ OpenAir applicator. Change was observed in the electro-acoustic signal with changes in substrate type (ceramic, steel, polymer). APPJ nozzle to substrate distance and substrate feature size were monitored. The decoding of the electro-acoustic emission yields three subdatasets that are described by three separate emission mechanisms. The three emissions are associated with the power supply fundamental drive frequency and its harmonics, the APPJ nozzle longitudinal mode acoustic emission and its odd overtones, and the acoustic surface reflection that is produced by the impedance mismatch between the discharge and the surface. Incorporating this knowledge into a LabVIEW program facilitated the continuous deconvolution of the electro-acoustic data. This enabled the use of specific frequency band test limits to control the APPJ treatment process which is sensitive to both plasma processing conditions and substrate type and features.

  2. Exploring the polymerization of bioactive nano-cones on the inner surface of an organic tube by an atmospheric pressure pulsed micro-plasma jet

    NASA Astrophysics Data System (ADS)

    Xu, H. M.; Yu, J. S.; Chen, G. L.; Qiu, X. P.; Hu, W.; Chen, W. X.; Bai, H. Y.

    2015-12-01

    In this paper, the successful deposition of acrylic acid polymer (PAA) nano-cones on the inner surface of a polyvinyl chloride (PVC) tube using an atmospheric pressure pulsed plasma jet (APPJ) with acrylic acid (AA) monomer is presented. Optical emission spectroscopy (OES) measurements indicated that various reactive radicals, such as rad OH and rad O, existed in the plasma jet. Moreover, the pulsed current proportionally increased with the increase in the applied voltage. The strengthened stretching vibration of the carbonyl group (Cdbnd O) at 1700 cm-1, shown in the ATR-FTIR spectra, clearly indicated that the PAA was deposited on the PVC surface. The maximum height of the PAA nano-cones deposited by this method ranged from 150 to 200 nm. FTIR and XPS results confirmed the enhanced exposure of the carboxyl groups on the modified PVC surface, which was considered highly beneficial for successfully immobilizing a high density of biomolecules. The XPS data showed that the carbon ratios of the Csbnd OH/R and COOH/R groups increased from 7.03% and 2.6% to 18.69% and 6.81%, respectively (more than doubled) when an Ar/O2 plasma with AA monomer was applied to treat the inner surface of the PVC tube. Moreover, the enhanced attachment density of MC3T3-E1 bone cells was observed on the PVC inner surface coated with PAA nano-cones.

  3. [Characterization of an atmospheric pressure DC microplasma jet].

    PubMed

    Zheng, Pei-Chao; Wang, Hong-Mei; Li, Jian-Quan; Han, Hai-Yan; Xu, Guo-Hua; Shen, Cheng-Yin; Chu, Yan-Nan

    2009-02-01

    In the present work, a simply designed and easy made micrometer plasma jet device operating under atmospheric pressure was characterized. The microplasma jet operates in many kinds of working gas at atmospheric pressure, such as Ar, He, N2 etc, and is powered by a direct current power source. It can generate high current density glow discharge. In order to identify various excited species generated by the direct current microplasma jet device, the optical emission spectra of the jet with argon or nitrogen as working gas were studied. Based on the optical emission spectroscopy analysis of argon microplasma jet, the electron excitation temperature was determined to be about 3 000 K by the intensity ratio of two spectral lines. It is much lower than the electron excitation temperature of atmospheric pressure plasma torch, and hints that the atmospheric pressure direct current microplasma jet is cold compared with the atmospheric pressure plasma torch. The emission spectra of the N2 second positive band system were used to determine the vibrational temperature of the atmospheric pressure direct current microplasma jet. The experimental result shows that the molecular vibrational temperature of N2 is about 2 500 K. The electron density of the microplasma jet is about 10(13) cm(-3), which can be estimated from the electrical parameters of the discharge in the microplasma jet. A simple example of application of the microplasma jet is given. General print paper surface was modified with the microplasma jet and afterwards a droplet test was carried out. It was shown that the microplasma jet is more efficient in changing the hydrophilicity of general print paper.

  4. Reactive species profile in an atmospheric pressure plasma jet ignited in He and He/O2 mixture - implications for surface sterilization

    NASA Astrophysics Data System (ADS)

    Arjunan, Krishna Priya; Jones, Brendan; Ptasinska, Sylwia

    2015-09-01

    The enhanced chemistry and low temperature of cold atmospheric plasma (CAP) makes it a promising alternative to conventional sterilization techniques. Of the various configurations used for generating cold plasma, atmospheric pressure plasma jets (APPJs) are particularly interesting for biomedical applications since they can be used for targeted treatment of intricate geometries such as catheters due to their small dimensions. The present study shows the efficacy of an APPJ ignited in helium or He/O2 mixture in inactivating Escherichia coli (E.coli) bacterium on agar plate. To study the dependence of helium flow rate and sample distance on the inactivation area, E.coli spread on agar was treated for 10 min at various combinations of helium flow rates and sample distances from the nozzle. A ring-shaped inactivation area was observed in samples treated close to the jet nozzle. Addition of O2 significantly increased the inactivation area. The ring shaped inactivation area observed with only helium feed gas vanished with oxygen addition. The optical emission spectra of the core and jet region of the APPJ in helium and He/O2 were obtained. The profile of H2 O2 , NO2 -, NO2 - and O2 reaching the sample were determined using test strips arranged in a 3 × 3 array. A ring-shaped profile was observed for these species in samples treated close to the nozzle with helium APPJ, while no ring-shaped profile was observed with O2 addition. Addition of O2 increased O2 levels, and was detected up to 3 cm in the radial direction.

  5. Nonhomogeneous surface properties of parylene-C film etched by an atmospheric pressure He/O2 micro-plasma jet in ambient air

    NASA Astrophysics Data System (ADS)

    Wang, Tao; Yang, Bin; Chen, Xiang; Wang, Xiaolin; Yang, Chunsheng; Liu, Jingquan

    2016-10-01

    Surface properties of parylene-C film etched by an atmospheric pressure He/O2 micro-plasma jet in ambient air were investigated. The morphologies and chemical compositions of the etched surface were analyzed by optical microscopy, SEM, EDS, XPS and ATR-FTIR. The microscopy and SEM images showed the etched surface was nonhomogeneous with six discernable ring patterns from the center to the outside domain, which were composed of (I) a central region; (II) an effective etching region, where almost all of the parylene-C film was removed by the plasma jet with only a little residual parylene-C being functionalized with carboxyl groups (Cdbnd O, Osbnd Cdbnd O-); (III) an inner etching boundary; (IV) a middle etching region, where the film surface was smooth and partially removed; (V) an outer etching boundary, where the surface was decorated with clusters of debris, and (VI) a pristine parylene-C film region. The analysis of the different morphologies and chemical compositions illustrated the different localized etching process in the distinct regions. Besides, the influence of O2 flow rate on the surface properties of the etched parylene-C film was also investigated. Higher volume of O2 tended to weaken the nonhomogeneous characteristics of the etched surface and improve the etched surface quality.

  6. Induced apoptosis in melanocytes cancer cell and oxidation in biomolecules through deuterium oxide generated from atmospheric pressure non-thermal plasma jet

    NASA Astrophysics Data System (ADS)

    Kumar, Naresh; Attri, Pankaj; Yadav, Dharmendra Kumar; Choi, Jinsung; Choi, Eun Ha; Uhm, Han Sup

    2014-12-01

    Recently, atmospheric-pressure non-thermal plasma-jets (APPJ) are being for the cancer treatment. However, APPJ still has drawbacks such as efficiency and rise in temperature after treatment. So, in this work, a synergetic agent D2O vapour is attached to APPJ which not only increase the efficiency of plasma source against cancer treatment, but also controlled the temperature during the treatment. OD generated by the combination of D2O + N2 plasma helped in enhancing the efficiency of APPJ. We observed OD induced apoptosis on melanocytes G361 cancer cells through DNA damage signalling cascade. Additionally, we observed that plasma induces ROS, which activated MAPK p38 and inhibits p42/p44 MAPK, leading to cancer cell death. We have also studied DNA oxidation by extracting DNA from treated cancer cell and then analysed the effects of OD/OH/D2O2/H2O2 on protein modification and oxidation. Additionally, we attempted molecular docking approaches to check the action of D2O2 on the apoptosis related genes. Further, we confirmed the formation of OD/OH simultaneously in the solution using optical emission spectroscopy. Moreover, the simultaneous generation of D2O2/H2O2 was detected by the use of confocal Raman spectroscopy and density measurements.

  7. A Comparative Study of Polymer and Biomolecule Surface Modifications by an Atmospheric Pressure Plasma Jet and Surface Microdischarge in Controlled Environments

    NASA Astrophysics Data System (ADS)

    Bartis, Elliot; Knoll, Andrew; Luan, Pingshan; Hart, Connor; Seog, Joonil; Oehrlein, Gottlieb; Graves, David; Lempert, Walter

    2014-10-01

    In this work, polymer- and lipopolysaccharide-coated Si substrates were exposed to a surface microdischarge (SMD) and an atmospheric pressure plasma jet (APPJ) in controlled ambients. We seek to understand how plasma-ambient interactions impact biodeactivation and surface modifications by regulating the ambient gas chemistry and the proximity of the plasma to the ambient. A key difference between the SMD and APPJ is that the APPJ needs an Ar feed gas and the SMD does not. By adding small N2/O2 admixtures to Ar, we find that the O2 admixture in the APPJ is a key factor for both deactivation and surface modification. After plasma treatments, we detected a new chemical species on a variety of surfaces that was identified as NO3. We find that NO3 forms even with no N2 in the feed gas, demonstrating that this species forms due to interactions with ambient N2. Despite a very different discharge mechanism, the SMD modifies surfaces similarly to the APPJ, including NO3 formation. The SMD generates large O3 concentrations, which do not correlate with NO3, suggesting that O3 alone is not involved in the NO3 formation mechanism. The authors gratefully acknowledge financial support by the US Department of Energy (DE-SC0005105 and DE-SC0001939) and National Science Foundation (PHY-1004256).

  8. Induced apoptosis in melanocytes cancer cell and oxidation in biomolecules through deuterium oxide generated from atmospheric pressure non-thermal plasma jet.

    PubMed

    Kumar, Naresh; Attri, Pankaj; Yadav, Dharmendra Kumar; Choi, Jinsung; Choi, Eun Ha; Uhm, Han Sup

    2014-12-23

    Recently, atmospheric-pressure non-thermal plasma-jets (APPJ) are being for the cancer treatment. However, APPJ still has drawbacks such as efficiency and rise in temperature after treatment. So, in this work, a synergetic agent D2O vapour is attached to APPJ which not only increase the efficiency of plasma source against cancer treatment, but also controlled the temperature during the treatment. OD generated by the combination of D2O + N2 plasma helped in enhancing the efficiency of APPJ. We observed OD induced apoptosis on melanocytes G361 cancer cells through DNA damage signalling cascade. Additionally, we observed that plasma induces ROS, which activated MAPK p38 and inhibits p42/p44 MAPK, leading to cancer cell death. We have also studied DNA oxidation by extracting DNA from treated cancer cell and then analysed the effects of OD/OH/D2O2/H2O2 on protein modification and oxidation. Additionally, we attempted molecular docking approaches to check the action of D2O2 on the apoptosis related genes. Further, we confirmed the formation of OD/OH simultaneously in the solution using optical emission spectroscopy. Moreover, the simultaneous generation of D2O2/H2O2 was detected by the use of confocal Raman spectroscopy and density measurements.

  9. Effects of Ionization, Thermal Transport, and Radiation on Scaling Performance for Peak Pressure in Imploding Plasma Liners Formed by Converging Jets

    NASA Astrophysics Data System (ADS)

    Stanic, Milos; Cassibry, Jason; Hsu, Scott

    2012-10-01

    This paper is an extension of work done by (Cassibry et.al., in preparation) who performed similar research using Smoothed Particle Hydrodynamics Code (SPHC) with an ideal gas equation of state model, neglecting electron-thermal conduction, radiation conduction and radiation losses (in cases of optically thin plasma). SPHC has been modified to use a tabular equation of state, accounting for ionization effects and to include the mentioned thermal transport models. Series of simulations have been carried out and the results were analyzed in terms of recognizing the scaling laws for peak pressure and dwell time. Comparison with the previous work of (Cassibry et.al., in preparation) has also been carried out in an attempt to isolate and recognize the effects of ionization and thermal transport models. The work has been done in support of the Plasma Liner Experiment (PLX), which is a multi-institutional project working on validation of the imploding plasma liner concept for reaching High Energy Density (HEDP) regimes and a possible stand-off solution for Plasma Jet driven Magneto-Inertial Fusion (PJMIF).

  10. Induced apoptosis in melanocytes cancer cell and oxidation in biomolecules through deuterium oxide generated from atmospheric pressure non-thermal plasma jet

    PubMed Central

    Kumar, Naresh; Attri, Pankaj; Yadav, Dharmendra Kumar; Choi, Jinsung; Choi, Eun Ha; Uhm, Han Sup

    2014-01-01

    Recently, atmospheric-pressure non-thermal plasma-jets (APPJ) are being for the cancer treatment. However, APPJ still has drawbacks such as efficiency and rise in temperature after treatment. So, in this work, a synergetic agent D2O vapour is attached to APPJ which not only increase the efficiency of plasma source against cancer treatment, but also controlled the temperature during the treatment. OD generated by the combination of D2O + N2 plasma helped in enhancing the efficiency of APPJ. We observed OD induced apoptosis on melanocytes G361 cancer cells through DNA damage signalling cascade. Additionally, we observed that plasma induces ROS, which activated MAPK p38 and inhibits p42/p44 MAPK, leading to cancer cell death. We have also studied DNA oxidation by extracting DNA from treated cancer cell and then analysed the effects of OD/OH/D2O2/H2O2 on protein modification and oxidation. Additionally, we attempted molecular docking approaches to check the action of D2O2 on the apoptosis related genes. Further, we confirmed the formation of OD/OH simultaneously in the solution using optical emission spectroscopy. Moreover, the simultaneous generation of D2O2/H2O2 was detected by the use of confocal Raman spectroscopy and density measurements. PMID:25534001

  11. Deposition of organosilicone thin film from hexamethyldisiloxane (HMDSO) with 50 kHz/33 MHz dual-frequency atmospheric-pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Jiaojiao, LI; Qianghua, YUAN; Xiaowei, CHANG; Yong, WANG; Guiqin, YIN; Chenzhong, DONG

    2017-04-01

    The deposition of organosilicone thin films from hexamethyldisiloxane(HMDSO) by using a dual-frequency (50 kHz/33 MHz) atmospheric-pressure micro-plasma jet with an admixture of a small volume of HMDSO and Ar was investigated. The topography was measured by using scanning electron microscopy. The chemical bond and composition of these films were analyzed by Fourier transform infrared spectroscopy (FTIR) and x-ray photoelectron spectroscopy. The results indicated that the as-deposited film was constituted by silicon, carbon, and oxygen elements, and FTIR suggested the films are organosilicon with the organic component (–CH x ) and hydroxyl functional group(–OH) connected to the Si–O–Si backbone. Thin-film hardness was recorded by an MH–5–VM Digital Micro-Hardness Tester. Radio frequency power had a strong impact on film hardness and the hardness increased with increasing power.

  12. Evaluation of the treatment of both sides of raw chicken breasts with an atmospheric pressure plasma jet for the inactivation of Escherichia coli.

    PubMed

    Yong, Hae In; Kim, Hyun-Joo; Park, Sanghoo; Choe, Wonho; Oh, Mi Wha; Jo, Cheorun

    2014-08-01

    Atmospheric pressure plasma (APP) is an emerging nonthermal microbial inactivation technique. In this study, agar and raw chicken breast were inoculated with Escherichia coli and treated with an APP jet based on cold arc plasma. The aim of this study was to investigate the optimum conditions for the plasma treatment of an APP jet in order to maximize the efficiency of E. coli inactivation. The combination of N2+O2 (10 standard cubic centimeters per minute) and a longer treatment time (10 min) resulted in the highest inactivation of E. coli on agar plates with an optimum treatment distance of 20 mm. The samples in dry and wet conditions showed similar reductions in E. coli count when one side of the samples was treated at a given treatment time. Treating both sides-2.5 min on each side-resulted in a higher growth inhibition of E. coli than treatment of a single side only for 5 min. However, there was no significant difference between one-side treated samples (10 min) and both-sides treated samples (5+5 min). When the concentration of E. coli in the chicken breast sample was 10(4) colony-forming units (CFU)/g, the reduction rate of the E. coli was the highest, followed by 10(5), 10(6), and 10(7) CFU/g; however, no difference was found between 10(3) and 10(4) CFU/g. In conclusion, various treatment conditions may affect the inactivation efficiency of E. coli. In the present study, the optimum condition was determined as the treatment distance of 20 mm and longer treatment time (10 min) with the addition of oxygen to the nitrogen gas flow. Furthermore, the cell concentration of sample was an important parameter for the efficacy of the inactivation process.

  13. Absolute OH and O radical densities in effluent of a He/H2O micro-scaled atmospheric pressure plasma jet

    NASA Astrophysics Data System (ADS)

    Benedikt, J.; Schröder, D.; Schneider, S.; Willems, G.; Pajdarová, A.; Vlček, J.; Schulz-von der Gathen, V.

    2016-08-01

    The effluent of a micro-scaled atmospheric pressure plasma jet (μ-APPJ) operated in helium with admixtures of water vapor (≲ {{10}4} ppm) has been analyzed by means of cavity ring-down laser absorption spectroscopy and molecular beam mass spectrometry to measure hydroxyl (OH) radical densities, and by two-photon absorption laser-induced fluorescence spectroscopy to measure atomic oxygen (O) densities. Additionally, the performance of the bubbler as a source of water vapor in the helium feed gas has been carefully characterized and calibrated. The largest OH and O densities in the effluent of 2× {{10}14}~\\text{c}{{\\text{m}}-3} and 3.2× {{10}13}~\\text{c}{{\\text{m}}-3} , respectively, have been measured at around 6000 ppm. The highest selectivity is reached around 1500 ppm, where the OH density is at  ∼63% of its maximum value and is 14 times larger than the O density. The measured density profiles and distance variations are compared to the results of a 2D axially symmetric fluid model of species transport and reaction kinetics in the plasma effluent. It is shown that the main loss of OH radicals in the effluent is their mutual reaction. In the case of O, reactions with other species than OH also have to be considered to explain the density decay in the effluent. The results presented here provide additional information for understanding the plasma-chemical processes in non-equilibrium atmospheric pressure plasmas. They also open the way to applying μ-APPJ with He/H2O as a selective source of OH radicals.

  14. Fast incorporation of primary amine group into polylactide surface for improving C₂C₁₂ cell proliferation using nitrogen-based atmospheric-pressure plasma jets.

    PubMed

    Yang, Yi-Wei; Wu, Jane-Yii; Liu, Chih-Tung; Liao, Guo-Chun; Huang, Hsuan-Yu; Hsu, Ray-Quen; Chiang, Ming-Hung; Wu, Jong-Shinn

    2014-01-01

    In this article, we report the development of the fast incorporation of primary amine functional groups into a polylactide (PLA) surface using the post-discharge jet region of an atmospheric-pressure nitrogen-based dielectric barrier discharge (DBD). Plasma treatments were carried out in two sequential steps: (1) nitrogen with 0.1% oxygen addition, and (2) nitrogen with 5% ammonia addition. The analyses show that the concentration of N/C ratio, surface energy, contact angle, and surface roughness of the treated PLA surface can reach 19.1%, 70.5 mJ/m(2), 38° and 73.22 nm, respectively. In addition, the proposed two-step plasma treatment procedure can produce a PLA surface exhibiting almost the same C2C12 cell attachment and proliferation performance as that of the conventional gelatin coating method. Most importantly, the processing/preparation time is reduced from 13-15 h (gelatin coating method) to 5-15 min (two-step plasma treatment), which is very useful in practical applications.

  15. Picosecond-TALIF and VUV absorption measurements of absolute atomic nitrogen densities from an RF atmospheric pressure plasma jet with He/O2/N2 gas mixtures

    NASA Astrophysics Data System (ADS)

    West, Andrew; Niemi, Kari; Schröter, Sandra; Bredin, Jerome; Gans, Timo; Wagenaars, Erik

    2015-09-01

    Reactive Oxygen and Nitrogen species (RONS) from RF atmospheric pressure plasma jets (APPJs) are important in biomedical applications as well as industrial plasma processing such as surface modification. Atomic oxygen has been well studied, whereas, despite its importance in the plasma chemistry, atomic nitrogen has been somewhat neglected due to its difficulty of measurement. We present absolute densities of atomic nitrogen in APPJs operating with He/O2/N2 gas mixtures in open air, using picosecond Two-photon Absorption Laser Induced Fluorescence (ps-TALIF) and vacuum ultra-violet (VUV) absorption spectroscopy. In order to apply the TALIF technique in complex, He/O2/N2 mixtures, we needed to directly measure the collisional quenching effects using picosecond pulse widths (32ps). Traditional calculated quenching corrections, used in nanosecond TALIF, are inadequate due to a lack of quenching data for complex mixtures. Absolute values for the densities were found by calibrating against a known density of Krypton. The VUV absorption experiments were conducted on the DESIRS synchrotron beamline using a unique VUV Fourier-transform spectrometer. Atomic nitrogen densities were on the order of 1020 m-3 with good agreement between TALIF and VUV absorption. UK EPSRC grant EP/K018388/1.

  16. A 1D (radial) Plasma Jet Propagation Study for the Plasma Liner Experiment (PLX)

    NASA Astrophysics Data System (ADS)

    Thompson, J. R.; Bogatu, I. N.; Galkin, S. A.; Kim, J. S.; Welch, D. R.; Thoma, C.; Golovkin, I.; Macfarlane, J. J.; Case, A.; Messer, S. J.; Witherspoon, F. D.; Cassibry, J. T.; Awe, T. J.; Hsu, S. C.

    2011-10-01

    The Plasma Liner Experiment will explore the formation of imploding spherical ``plasma liners'' that reach peak pressures of 0.1 Mbar upon stagnation. The liners will be formed through the merging of dense, high velocity plasma jets (n ~1017 cm-3, T ~3 eV, v ~50 km/s) in a spherically convergent geometry. The focus of this 1D (radial) study is argon plasma jet evolution during propagation from the rail gun source to the jet merging radius. The study utilizes the Large Scale Plasma (LSP) PIC code with atomic physics included through the use of a non-Local Thermal Equilibrium (NLTE) Equation of State (EOS) table. We will present scenarios for expected 1D (radial) plasma jet evolution, from upon exiting the PLX rail gun to reaching the jet merging radius. The importance of radiation cooling early in the simulation is highlighted. Work supported by US DOE grant DE-FG02-05ER54835.

  17. Pressure Modulated Sonic Jet in Supersonic Crossflow

    NASA Astrophysics Data System (ADS)

    Rossmann, Tobias

    2014-11-01

    Sonic transverse jets in supersonic crossflow are modulated using high-amplitude variations in jet stagnation pressure to enhance jet penetration and mixing. An injection/modulation apparatus combining a powered resonance tube and acoustic resonator is used to create low momentum ratio jets (J = 1 , 2) in a supersonic cross-stream (M = 3 . 5). The injector has the capability to modulate the jet supply pressure at sufficiently high frequency (> 15 kHz) and amplitude (up to 190 dB) to access relevant Strouhal numbers (St = 0 - 0 . 3) and amplitudes (up to 10% of the jet stagnation pressure) related to mixing enhancement. Planar laser Mie scattering in both side and end views allows for instantaneous imaging of the jet fluid to quantify jet trajectory, spread, and mixing behavior. For modulated J = 2 transverse jets, the recirculation zone directly downstream of the injection location is eliminated and significantly faster centerline signal decay rates are seen. For the J = 1 modulated jets, substantial increases in centerline penetration, jet spread, and centerline signal decay rate are shown. Additionally, PDF analysis of the instantaneous jet fluid signal values is performed to compare local mixing efficiencies between the modulated and un-modulated cases.

  18. Pressure and Magnetics Measurements of Single and Merged Jets

    NASA Astrophysics Data System (ADS)

    Messer, S.; Case, A.; Brockington, S.; Bomgardner, R.; Witherspoon, F. D.

    2010-11-01

    We present pressure and magnetic data from both a single full scale coaxial gun and from the merging of jets from several minirailguns. The magnetic probes measure all three components of field, and include an array of probes inside the coaxial gun. Magnetic measurements beyond the muzzle of the gun show the scale of currents trapped in the plasma plume. The pressure probe measures adiabatic stagnation pressure and shows how this quantity decreases with distance from the gun as well as the changes in stagnation pressure through the merge process. Stagnation pressure is influenced by density, temperature, and velocity, and serves as a check on spectroscopic and interferometer measurements. Unlike optical measurements, stagnation pressure is taken at a definite location. These guns are early prototypes of guns to be installed on the Plasma Liner eXperiment at LANL. The jet-merging results are reviewed in the context of what is expected for PLX.

  19. Spectroscopic studies of non-thermal plasma jet at atmospheric pressure formed in low-current nonsteady-state plasmatron for biomedical applications

    NASA Astrophysics Data System (ADS)

    Demkin, V. P.; Melnichuk, S. V.; Demkin, O. V.; Kingma, H.; Van de Berg, R.

    2016-04-01

    The optical and electrophysical characteristics of the nonequilibrium low-temperature plasma formed by a low-current nonsteady-state plasmatron are experimentally investigated in the present work. It is demonstrated that experimental data on the optical diagnostics of the plasma jet can provide a basis for the construction of a self-consistent physical and mathematical plasma model and for the creation of plasma sources with controllable electrophysical parameters intended for the generation of the required concentration of active particles. Results of spectroscopic diagnostics of plasma of the low-current nonsteady-state plasmatron confirm that the given source is efficient for the generation of charged particles and short-wavelength radiation—important plasma components for biomedical problems of an increase in the efficiency of treatment of biological tissues by charged particles. Measurement of the spatial distribution of the plasma jet potential by the probe method has demonstrated that a negative space charge is formed in the plasma jet possibly due to the formation of electronegative oxygen ions.

  20. Etching of silicon surfaces using atmospheric plasma jets

    NASA Astrophysics Data System (ADS)

    Paetzelt, H.; Böhm, G.; Arnold, Th

    2015-04-01

    Local plasma-assisted etching of crystalline silicon by fine focused plasma jets provides a method for high accuracy computer controlled surface waviness and figure error correction as well as free form processing and manufacturing. We investigate a radio-frequency powered atmospheric pressure He/N2/CF4 plasma jet for the local chemical etching of silicon using fluorine as reactive plasma gas component. This plasma jet tool has a typical tool function width of about 0.5 to 1.8 mm and a material removal rate up to 0.068 mm3 min-1. The relationship between etching rate and plasma jet parameters is discussed in detail regarding gas composition, working distance, scan velocity and RF power. Surface roughness after etching was characterized using atomic force microscopy and white light interferometry. A strong smoothing effect was observed for etching rough silicon surfaces like wet chemically-etched silicon wafer backsides. Using the dwell-time algorithm for a deterministic surface machining by superposition of the local removal function of the plasma tool we show a fast and efficient way for manufacturing complex silicon structures. In this article we present two examples of surface processing using small local plasma jets.

  1. Optimizing Dense Plasma Focus Neutron Yields with Fast Gas Jets

    NASA Astrophysics Data System (ADS)

    McMahon, Matthew; Kueny, Christopher; Stein, Elizabeth; Link, Anthony; Schmidt, Andrea

    2016-10-01

    We report a study using the particle-in-cell code LSP to perform fully kinetic simulations modeling dense plasma focus (DPF) devices with high density gas jets on axis. The high density jet models fast gas puffs which allow for more mass on axis while maintaining the optimal pressure for the DPF. As the density of the jet compared to the background fill increases we find the neutron yield increases, as does the variability in the neutron yield. Introducing perturbations in the jet density allow for consistent seeding of the m =0 instability leading to more consistent ion acceleration and higher neutron yields with less variability. Jets with higher on axis density are found to have the greatest yield. The optimal jet configuration is explored. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

  2. Jet flow and premixed jet flame control by plasma swirler

    NASA Astrophysics Data System (ADS)

    Li, Gang; Jiang, Xi; Zhao, Yujun; Liu, Cunxi; Chen, Qi; Xu, Gang; Liu, Fuqiang

    2017-04-01

    A swirler based on dielectric barrier discharge plasma actuators is designed and its effectiveness in both jet flow and premixed jet flame control is demonstrated. In contrast to traditional spanwise-oriented actuators, plasma actuators are placed along the axial direction of the injector to induce a circumferential velocity to the main flow and create a swirl flow without any insertion or moving part. In the DBD plasma swirl injector, the discharge does not ignite the mixture nor does it induce flashback. Flame visualization is obtained by cameras while velocity profiles are obtained by Laser Doppler Anemometry measurements. The results obtained indicate the effectiveness of the new design.

  3. Modelling the Plasma Jet in Multi-Arc Plasma Spraying

    NASA Astrophysics Data System (ADS)

    Bobzin, K.; Öte, M.; Schein, J.; Zimmermann, S.; Möhwald, K.; Lummer, C.

    2016-08-01

    Particle in-flight characteristics in atmospheric plasma spraying process are determined by impulse and heat energy transferred between the plasma jet and injected powder particles. One of the important factors for the quality of the plasma-sprayed coatings is thus the distribution of plasma gas temperatures and velocities in plasma jet. Plasma jets generated by conventional single-arc plasma spraying systems and their interaction with powder particles were subject matter of intensive research. However, this does not apply to plasma jets generated by means of multi-arc plasma spraying systems yet. In this study, a numerical model has been developed which is designated to dealing with the flow characteristics of the plasma jet generated by means of a three-cathode spraying system. The upstream flow conditions, which were calculated using a priori conducted plasma generator simulations, have been coupled to the plasma jet simulations. The significances of the relevant numerical assumptions and aspects of the models are analyzed. The focus is placed on to the turbulence and diffusion/demixing modelling. A critical evaluation of the prediction power of the models is conducted by comparing the numerical results to the experimental results determined by means of emission spectroscopic computed tomography. It is evident that the numerical models exhibit a good accuracy for their intended use.

  4. The Study on Inhibition of Planktonic Bacterial Growth by Non-Thermal Atmospheric Pressure Plasma Jet Treated Surfaces for Dental Application.

    PubMed

    Yoo, Eun-Mi; Uhm, Soo-Hyuk; Kwon, Jae-Sung; Choi, Hye-Sook; Choi, Eun Ha; Kim, Kwang-Mahn; Kim, Kyoung-Nam

    2015-02-01

    Investigation of the effects by non-thermal atmospheric pressure plasma jet (NTAPPJ) treatment on the titanium dental implant surfaces for the inhibition of two common pathogens related with dental infections, Streptococcus mutans and Staphylococcus aureus, was carried out in this study. The commercially pure titanium was used as specimen, which were irradiated by NTAPPJ for 30, 60 and 120 seconds. Specimen without being treated with NTAPPJ was assigned as the control group. The X-ray photoelectron spectroscope and surface contact angle goniometer were used to analyze the effects of NTAPPJ treatment on surface chemistry and hydrophilicity of the specimen. The effects of the NTAPPJ treatment on surfaces, in terms of bacterial attachment, growth, morphology and structural changes were evaluated by the number of colony forming units (CFU) and scanning electron microscopy (SEM) observations. The results showed that there was a reduction of CFUs and the significant change in morphology of bacteria as they were cultured on the titanium surfaces treated with NTAPPJ. These results were related to surface chemical changes and hydrophilicity changes by NTAPPJ. The NTAPPJ treatment is very effective on the dental implant titanium surface treatment that resulted in the inhibition of bacteria and has a great potential to be a promising technique in various clinical dental applications.

  5. Air atmospheric pressure plasma jet pretreatment for drop-wise loading of dexamethasone on hydroxyapatite scaffold for increase of osteoblast attachment.

    PubMed

    Lee, Jung-Hwan; Kwon, Jae-Sung; Kim, Yong Hee; Choi, Eun Ha; Kim, Kwang-Mahn; Kim, Kyoung-Nam

    2014-10-01

    Periodontal disease affects alveolar bone resorption around the involved teeth. To gain bone height, bone graft materials have been widely used with drug carriers. Application of an atmospheric pressure plasma jet (APPJ) treatment is widely studied due to its ability to change surface characteristics without topographical change. The aim of this study is to identify whether the air APPJ (AAPPJ) treatment before drop-wise loading performance could change loaded amount of dexamethasone, and induce increase of cell attachment and proliferation. The results suggested that AAPPJ treatment decreased the contact angle down to about 13 degrees, which increased gradually but significantly lowered at least 4 days compared to no-treated group. After AAPPJ treatment, hydrocarbon was removed with change of zeta potential into positive charge. However, the AAPPJ treatment did not change the quantity or releasing profile of dexamethasone (p > 0.05). Confocal analysis combined with DNA proliferation analysis showed increase of osteoblast attachment and proliferation. Hence, AAPPJ could be a useful pretreatment method before drop-wise loading on HA scaffold with dexamethasone for increase of osteoblast attachment.

  6. High-efficiency impurity activation by precise control of cooling rate during atmospheric pressure thermal plasma jet annealing of 4H-SiC wafer

    NASA Astrophysics Data System (ADS)

    Maruyama, Keisuke; Hanafusa, Hiroaki; Ashihara, Ryuhei; Hayashi, Shohei; Murakami, Hideki; Higashi, Seiichiro

    2015-06-01

    We have investigated high-temperature and rapid annealing of a silicon carbide (SiC) wafer by atmospheric pressure thermal plasma jet (TPJ) irradiation for impurity activation. To reduce the temperature gradient in the SiC wafer, a DC current preheating system and the lateral back-and-forth motion of the wafer were introduced. A maximum surface temperature of 1835 °C within 2.4 s without sample breakage was achieved, and aluminum (Al), phosphorus (P), and arsenic (As) activations in SiC were demonstrated. We have investigated precise control of heating rate (Rh) and cooling rate (Rc) during rapid annealing of P+-implanted 4H-SiC and its impact on impurity activation. No dependence of resistivity on Rh was observed, while increasing Rc significantly decreased resistivity. A minimum resistivity of 0.0025 Ω·cm and a maximum carrier concentration of 2.9 × 1020 cm-3 were obtained at Rc = 568 °C/s.

  7. Atmospheric Pressure Room Temperature Plasma Jets Facilitate Oxidative and Nitrative Stress and Lead to Endoplasmic Reticulum Stress Dependent Apoptosis in HepG2 Cells

    PubMed Central

    Meng, Dandan; Lei, Qian; Li, Yin; Deng, Pengyi; Chen, Mingjie; Tu, Min; Lu, Xinpei; Yang, Guangxiao; He, Guangyuan

    2013-01-01

    Atmospheric pressure room temperature plasma jets (APRTP-Js) that can emit a mixture of different active species have recently found entry in various medical applications. Apoptosis is a key event in APRTP-Js-induced cellular toxicity, but the exact biological mechanisms underlying remain elusive. Here, we explored the role of reactive oxygen species (ROS) and reactive nitrogen species (RNS) in APRTP-Js-induced apoptosis using in vitro model of HepG2 cells. We found that APRTP-Js facilitated the accumulation of ROS and RNS in cells, which resulted in the compromised cellular antioxidant defense system, as evidenced by the inactivation of cellular antioxidants including glutathione (GSH), superoxide dismutase (SOD) and catalase. Nitrotyrosine and protein carbonyl content analysis indicated that APRTP-Js treatment caused nitrative and oxidative injury of cells. Meanwhile, intracellular calcium homeostasis was disturbed along with the alteration in the expressions of GRP78, CHOP and pro-caspase12. These effects accumulated and eventually culminated into the cellular dysfunction and endoplasmic reticulum stress (ER stress)-mediated apoptosis. The apoptosis could be markedly attenuated by N-acetylcysteine (NAC, a free radical scavenger), which confirmed the involvement of oxidative and nitrative stress in the process leading to HepG2 cell apoptosis by APRTP-Js treatment. PMID:24013954

  8. Mechanism of bullet-to-streamer transition in water surface incident helium atmospheric pressure plasma jet (APPJ)

    NASA Astrophysics Data System (ADS)

    Yoon, Sung-Young; Kim, Gon-Ho; Kim, Su-Jeong; Bae, Byeongjun; Kim, Seong Bong; Ryu, Seungmin; Yoo, Suk Jae

    2016-09-01

    The mechanism of bullet to streamer transition of helium-APPJ bullet on the electrolyte surface was investigated. The APPJ was discharged in pin-to-ring DBD reactor system with helium gas by applying the ac-driven voltage at a frequency of 10 kHz. The water evaporation was controlled via saline temperature. The temporal- and 2-dimensional spatially- resolved plasma properties are monitored by optical diagnostics. During the APPJ bullet propagation from reactor to electrolyte surface, the transition of bullet from streamer was recognized from the high speed image, hydrogen beta emission line, and bullet propagation speed. The He metastable species density profiles from the tunable diode laser absorption spectroscopy (TDLAS) showed the metastable lost the energy near electrolyte surface. It is found that the bullet transited to streamer when the water fraction reached to 29%. This can be fascinating result to study the plasma physics liquid surface, non-fixed boundary. Acknowledgements: This work was partly supported by R&D Program of `Plasma Advanced Technology for Agriculture and Food (Plasma Farming)' through the National Fusion Research Institute of Korea (NFRI) funded by the Government fund was carried out as part.

  9. On the use of the double floating probe method to infer the difference between the electron and the heavy particles temperatures in an atmospheric pressure, vortex-stabilized nitrogen plasma jet

    SciTech Connect

    Prevosto, L. Mancinelli, B. R.; Kelly, H.

    2014-05-15

    Sweeping double probe measurements in an atmospheric pressure direct current vortex-stabilized plasma jet are reported (plasma conditions: 100 A discharge current, N{sub 2} gas flow rate of 25 Nl/min, thoriated tungsten rod-type cathode, copper anode with 5 mm inner diameter). The interpretation of the double probe characteristic was based on a generalization of the standard double floating probe formulae for non-uniform plasmas coupled to a non-equilibrium plasma composition model. Perturbations caused by the current to the probe together with collisional and thermal processes inside the probe perturbed region were taken into account. Radial values of the average electron and heavy particle temperatures as well as the electron density were obtained. The calculation of the temperature values did not require any specific assumption about a temperature relationship between different particle species. An electron temperature of 10 900 ± 900 K, a heavy particle temperature of 9300 ± 900 K, and an electron density of about 3.5 × 10{sup 22} m{sup −3} were found at the jet centre at 3.5 mm downstream from the torch exit. Large deviations from kinetic equilibrium were found toward the outer border of the plasma jet. These results showed good agreement with those previously reported by the authors by using a single probe technique. The calculations have shown that this method is particularly useful for studying spraying-type plasma torches operated at power levels of about 15 kW.

  10. On the use of the double floating probe method to infer the difference between the electron and the heavy particles temperatures in an atmospheric pressure, vortex-stabilized nitrogen plasma jet.

    PubMed

    Prevosto, L; Kelly, H; Mancinelli, B R

    2014-05-01

    Sweeping double probe measurements in an atmospheric pressure direct current vortex-stabilized plasma jet are reported (plasma conditions: 100 A discharge current, N2 gas flow rate of 25 Nl/min, thoriated tungsten rod-type cathode, copper anode with 5 mm inner diameter). The interpretation of the double probe characteristic was based on a generalization of the standard double floating probe formulae for non-uniform plasmas coupled to a non-equilibrium plasma composition model. Perturbations caused by the current to the probe together with collisional and thermal processes inside the probe perturbed region were taken into account. Radial values of the average electron and heavy particle temperatures as well as the electron density were obtained. The calculation of the temperature values did not require any specific assumption about a temperature relationship between different particle species. An electron temperature of 10,900 ± 900 K, a heavy particle temperature of 9300 ± 900 K, and an electron density of about 3.5 × 10(22) m(-3) were found at the jet centre at 3.5 mm downstream from the torch exit. Large deviations from kinetic equilibrium were found toward the outer border of the plasma jet. These results showed good agreement with those previously reported by the authors by using a single probe technique. The calculations have shown that this method is particularly useful for studying spraying-type plasma torches operated at power levels of about 15 kW.

  11. Mixing in plasma and low density jets

    NASA Astrophysics Data System (ADS)

    Russ, S.; Strykowski, P. J.; Pfender, E.

    1994-04-01

    This study was undertaken to examine the mechanisms which produce the large entrainment measured near the exit of thermal plasma torches. A research facility was constructed to examine low density jet behavior under similar dimensionless conditions as those produced by thermal plasma spray torches; the Reynolds number based on jet diameter and average properties was 1000, and the ratio of jet to ambient density was 0.07. This very low density jet produced organized vortex structures which were partially responsible for the rapid entrainment of external air. The formation of these organized structures could be disrupted by introducing turbulence, but the rapid entrainment process was not significantly affected. The structure of the jet produced by a commercial plasma torch was examined and compared to the low density research jet. At low gas flow rates the plasma jet also displayed the formation of coherent vortex structures, the passage frequency of which compared favorably with that measured in the low density research jet. At higher gas flow rates the shear layer of the plasma jet rapidly broke down producing relatively small scale turbulence. Visualizations of the hot plasma core were compared against measurements of the torch voltage fluctuations caused by arc instabilities. At low flow rates the arc voltage fluctuations were quite low and the plume was very steady. At higher flow rates the arc voltage fluctuations increased and produced “surging” and “whipping” in the hot potential core. It is believed that this low frequency unsteadiness is partially responsible for the rapid entrainment measured in plasma torches.

  12. Fluctuating pressures in flow fields of jets

    NASA Technical Reports Server (NTRS)

    Schroeder, J. C.; Haviland, J. K.

    1976-01-01

    The powered lift configurations under present development for STOL aircraft are the externally blown flap (EBF), involving direct jet impingement on the aircraft flaps, and the upper surface blown (USB), where the jet flow is attached on the upper surface of the wing and directed downwards. Towards the goal of developing scaling laws to predict unsteady loads imposed on the structural components of these STOL aircraft from small model tests, the near field fluctuating pressure behavior for the simplified cases of a round free cold jet and the same jet impinging on a flat plate was investigated. Examples are given of coherences, phase lags (giving convection velocities), and overall fluctuating pressure levels measured. The fluctuating pressure levels measured on the flat plate are compared to surface fluctuating pressure levels measured on full-scale powered-lift configuration models.

  13. Patterned Surface Functionalization of Dot-Arrayed CNTs for Biochip Sensor Using Scannable Ultrafine Atmospheric Pressure Plasma Jet

    NASA Astrophysics Data System (ADS)

    Okada, Mitsuru; Abuzairi, Tomy; Bhattacharjee, Sudeep; Poespawati, Nji R.; Purnamaningsih, Rento W.; Nagatsu, Masaaki

    2015-09-01

    The present results show that the feasibility of using a dot-arrayed CNT as a biochip sensor was demonstrated by successfully fabricating CNTs in an array form and performing patterned surface functionalization of amino and carboxyl groups onto CNT. The vertically aligned CNT was fabricated in an array form using a combined thermal-plasma CVD for realizing the development of biochip sensors. Patterned surface functionalization was developed by ultrafine APPJ in two stages: (1) pretreatment by He gas with -500V dc bias and (2) posttreatment without bias by a He/NH3 gas mixture for amino group or by a He/O2 gas mixture for carboxyl group functionalization. The analysis results of chemical derivatization indicate that amino and carboxyl groups successfully functionalized the CNT dot array without interfering with each other. The optimum period of ultrafine APPJ treatments was achieved by balancing the following 3 aspects: (1) effective area of modification, (2) amount of surface functionalization, and (3) damage of the CNT. Finally, the patterned surface functionalization of amino and carboxyl groups was successfully conducted in the arbitrary pattern by using ultrafine APPJ automatically scanned by computer-controlled precision stage.

  14. Structure and Dynamics of Colliding Plasma Jets

    DOE PAGES

    Li, C.; Ryutov, D.; Hu, S.; ...

    2013-12-01

    Monoenergetic-proton radiographs of laser-generated, high-Mach-number plasma jets colliding at various angles shed light on the structures and dynamics of these collisions. The observations compare favorably with results from 2D hydrodynamic simulations of multistream plasma jets, and also with results from an analytic treatment of electron flow and magnetic field advection. In collisions of two noncollinear jets, the observed flow structure is similar to the analytic model’s prediction of a characteristic feature with a narrow structure pointing in one direction and a much thicker one pointing in the opposite direction. Spontaneous magnetic fields, largely azimuthal around the colliding jets and generatedmore » by the well-known ∇Te ×∇ne Biermann battery effect near the periphery of the laser spots, are demonstrated to be “frozen in” the plasma (due to high magnetic Reynolds number RM ~5×10⁴) and advected along the jet streamlines of the electron flow. These studies provide novel insight into the interactions and dynamics of colliding plasma jets.« less

  15. Structure and Dynamics of Colliding Plasma Jets

    SciTech Connect

    Li, C.; Ryutov, D.; Hu, S.; Rosenberg, M.; Zylstra, A.; Seguin, F.; Frenje, J.; Casey, D.; Gatu Johnson, M.; Manuel, M.; Rinderknecht, H.; Petrasso, R.; Amendt, P.; Park, H.; Remington, B.; Wilks, S.; Betti, R.; Froula, D.; Knauer, J.; Meyerhofer, D.; Drake, R.; Kuranz, C.; Young, R.; Koenig, M.

    2013-12-01

    Monoenergetic-proton radiographs of laser-generated, high-Mach-number plasma jets colliding at various angles shed light on the structures and dynamics of these collisions. The observations compare favorably with results from 2D hydrodynamic simulations of multistream plasma jets, and also with results from an analytic treatment of electron flow and magnetic field advection. In collisions of two noncollinear jets, the observed flow structure is similar to the analytic model’s prediction of a characteristic feature with a narrow structure pointing in one direction and a much thicker one pointing in the opposite direction. Spontaneous magnetic fields, largely azimuthal around the colliding jets and generated by the well-known ∇Te ×∇ne Biermann battery effect near the periphery of the laser spots, are demonstrated to be “frozen in” the plasma (due to high magnetic Reynolds number RM ~5×10⁴) and advected along the jet streamlines of the electron flow. These studies provide novel insight into the interactions and dynamics of colliding plasma jets.

  16. Surface modification of polymeric materials by cold atmospheric plasma jet

    NASA Astrophysics Data System (ADS)

    Kostov, K. G.; Nishime, T. M. C.; Castro, A. H. R.; Toth, A.; Hein, L. R. O.

    2014-09-01

    In this work we report the surface modification of different engineering polymers, such as, polyethylene terephthalate (PET), polyethylene (PE) and polypropylene (PP) by an atmospheric pressure plasma jet (APPJ). It was operated with Ar gas using 10 kV, 37 kHz, sine wave as an excitation source. The aim of this study is to determine the optimal treatment conditions and also to compare the polymer surface modification induced by plasma jet with the one obtained by another atmospheric pressure plasma source - the dielectric barrier discharge (DBD). The samples were exposed to the plasma jet effluent using a scanning procedure, which allowed achieving a uniform surface modification. The wettability assessments of all polymers reveal that the treatment leads to reduction of more than 40° in the water contact angle (WCA). Changes in surface composition and chemical bonding were analyzed by x-ray photoelectron spectroscopy (XPS) and Fourier-Transformed Infrared spectroscopy (FTIR) that both detected incorporation of oxygen-related functional groups. Surface morphology of polymer samples was investigated by Atomic Force Microscopy (AFM) and an increase of polymer roughness after the APPJ treatment was found. The plasma-treated polymers exhibited hydrophobic recovery expressed in reduction of the O-content of the surface upon rinsing with water. This process was caused by the dissolution of low molecular weight oxidized materials (LMWOMs) formed on the surface as a result of the plasma exposure.

  17. Laboratory-produced MHD plasma jets

    NASA Astrophysics Data System (ADS)

    Bellan, Paul

    2008-04-01

    Because space plasmas are neither confined by vacuum chamber walls nor have magnetic fields produced by physical coils, space plasmas have shapes that are much less determinate than lab plasmas. An experimental program underway at Caltech produces plasmas where the shape is neither fixed by a vacuum chamber wall nor imposed by an external coil set, but rather is allowed to be determined by self-organizing MHD processes subject to the constraint of imposed boundary conditions analogous to the boundary conditions of space plasmas. These self-organizing processes are believed to be fundamental to astrophysical jets, solar coronal loops, and MHD turbulence (e.g. Taylor relaxation). The experimental dynamics are sufficiently reproducible to allow detailed study despite the morphology being complex and dynamic. A surprising result has been the observation that instead of the plasma uniformly filling up the available volume, the plasma is spatially localized in a highly collimated, small diameter magnetic flux tube, the length and axis of which change in time in response to MHD forces. A model shows that the collimation results from stagnation of linked magnetic flux frozen into a MHD-driven jet that accelerates plasma from the wall into the flux tube, filling the flux tube with plasma. Jet flow has been imaged with a high-speed multi-frame camera, diagnosed via Doppler spectroscopy, and most recently (i) the collision between two opposing, color-coded jets flowing from opposite ends of a flux tube has been observed, and (ii) the collision of a jet with a target cloud has been observed.

  18. Particle transport in pellet fueled JET (Jet European Torus) plasmas

    SciTech Connect

    Baylor, L.R.

    1990-01-01

    Pellet fueling experiments have been carried out on the Joint European Torus (JET) tokamak with a multi-pellet injector. The pellets are injected at speeds approaching 1400 m/s and penetrate deep into the JET plasma. Highly peaked electron density profiles are achieved when penetration of the pellets approaches or goes beyond the magnetic axis, and these peaked profiles persist for more than two seconds in ohmic discharges and over one second in ICRF heated discharges. In this dissertation, analysis of electron particle transport in multi-pellet fueled JET limiter plasmas under a variety of heating conditions is described. The analysis is carried out with a one and one-half dimensional radial particle transport code to model the experimental density evolution with various particle transport coefficients. These analyses are carried out in plasmas with ohmic heating, ICRF heating, and neural beam heating, in limiter configurations. Peaked density profile cases are generally characterized by diffusion coefficients with a central (r/a < 0.5) diffusivity {approximately}0.1 m{sup 2}/s that increases rapidly to {approximately}0.3 m{sup 2}/s at r/a = 0.6 and then increases out to the plasma edge as (r/a){sup 2}. These discharges can be satisfactorily modeled without any anomalous convective (pinch) flux. 79 refs., 60 figs.

  19. On the structure of plasma liners for plasma jet induced magnetoinertial fusion

    SciTech Connect

    Kim, Hyoungkeun; Zhang, Lina; Samulyak, Roman; Parks, Paul

    2013-02-15

    The internal structure and self-collapse properties of plasma liners, formed by the merger of argon plasma jets, have been studied via 3-dimensional numerical simulations using the FronTier code. We have shown that the jets merger process is accomplished through a cascade of oblique shock waves that heat the liner and reduce its Mach number. Oblique shock waves and the adiabatic compression heating have led to the 10 times reduction of the self-collapse pressure of a 3-dimensional argon liner compared to a spherically symmetric liner with the same pressure and density profiles at the merging radius. We have also observed a factor of 10 variations of pressure and density in the leading edge of the liner along spherical surfaces close to the interaction with potential plasma targets. Such a non-uniformity of imploding plasma liners presents problems for the stability of targets during compression.

  20. High pressure water jet mining machine

    DOEpatents

    Barker, Clark R.

    1981-05-05

    A high pressure water jet mining machine for the longwall mining of coal is described. The machine is generally in the shape of a plowshare and is advanced in the direction in which the coal is cut. The machine has mounted thereon a plurality of nozzle modules each containing a high pressure water jet nozzle disposed to oscillate in a particular plane. The nozzle modules are oriented to cut in vertical and horizontal planes on the leading edge of the machine and the coal so cut is cleaved off by the wedge-shaped body.

  1. Observation of Confined Current Ribbon in JET Plasmas

    SciTech Connect

    Solano, E. R.; Barrera, L.; Luna, E. de la; Lopez-Fraguas, A.; Lomas, P. J.; Alper, B.; Andrew, Y.; Arnoux, G.; Boboc, A.; Beurskens, M. N. A.; Brix, M.; Gerasimov, S.; Giroud, C.; Howell, D.; Korotkov, A.; Saarelma, S.; Sirinelli, A.; Pinches, S. D.; Zabeo, L.

    2010-05-07

    We report the identification of a localized current structure inside the JET plasma. It is a field-aligned closed helical ribbon, carrying current in the same direction as the background current profile (cocurrent), rotating toroidally with the ion velocity (corotating). It appears to be located at a flat spot in the plasma pressure profile, at the top of the pedestal. The structure appears spontaneously in low density, high rotation plasmas, and can last up to 1.4 s, a time comparable to a local resistive time. It considerably delays the appearance of the first edge localized mode.

  2. Tendency of spherically imploding plasma liners formed by merging plasma jets to evolve toward spherical symmetry

    SciTech Connect

    Cassibry, J. T.; Stanic, M.; Hsu, S. C.; Witherspoon, F. D.; Abarzhi, S. I.

    2012-05-15

    We have performed three-dimensional (3D) simulations using smoothed particle hydrodynamics (SPH) in order to study the effects of discrete plasma jets on the processes of plasma liner formation, implosion on vacuum, and expansion. It was found that the pressure histories of the inner portion of the liner from 3D SPH simulations with a uniform liner and with 30 discrete plasma jets were qualitatively and quantitatively similar from peak compression through the complete stagnation of the liner. The 3D simulations with a uniform liner were first benchmarked against results from one-dimensional radiation-hydrodynamic simulations [T. J. Awe et al., Phys. Plasmas 18, 072705 (2011)]. Two-dimensional plots of the pressure field show that the discrete jet SPH case evolves towards a profile that is almost indistinguishable from the SPH case with a uniform liner, thus indicating that non-uniformities due to discrete jets are smeared out by late stages of the implosion. The processes of plasma liner formation and implosion on vacuum were shown to be robust against Rayleigh-Taylor instability growth. Finally, interparticle mixing for a liner imploding on vacuum was investigated. The mixing rate was found to be very small until after the peak compression for the 30 jet simulations.

  3. Laboratory plasma physics experiments using merging supersonic plasma jets

    SciTech Connect

    Hsu, S. C.; Moser, A. L.; Merritt, E. C.; Adams, C. S.; Dunn, J. P.; Brockington, S.; Case, A.; Gilmore, M.; Lynn, A. G.; Messer, S. J.; Witherspoon, F. D.

    2015-04-01

    We describe a laboratory plasma physics experiment at Los Alamos National Laboratory that uses two merging supersonic plasma jets formed and launched by pulsed-power-driven railguns. The jets can be formed using any atomic species or mixture available in a compressed-gas bottle and have the following nominal initial parameters at the railgun nozzle exit: ne ≈ ni ~ 10¹⁶ cm⁻³, Te ≈ Ti ≈ 1.4 eV, Vjet ≈ 30–100 km/s, mean charge $\\bar{Z}$ ≈ 1, sonic Mach number Ms ≡ Vjet/Cs > 10, jet diameter = 5 cm, and jet length ≈ 20 cm. Experiments to date have focused on the study of merging-jet dynamics and the shocks that form as a result of the interaction, in both collisional and collisionless regimes with respect to the inter-jet classical ion mean free path, and with and without an applied magnetic field. However, many other studies are also possible, as discussed in this paper.

  4. Atmospheric-Pressure Plasma Interaction with Soft Materials as Fundamental Processes in Plasma Medicine.

    PubMed

    Takenaka, Kosuke; Miyazaki, Atsushi; Uchida, Giichiro; Setsuhara, Yuichi

    2015-03-01

    Molecular-structure variation of organic materials irradiated with atmospheric pressure He plasma jet have been investigated. Optical emission spectrum in the atmospheric-pressure He plasma jet has been measured. The spectrum shows considerable emissions of He lines, and the emission of O and N radicals attributed to air. Variation in molecular structure of Polyethylene terephthalate (PET) film surface irradiated with the atmospheric-pressure He plasma jet has been observed via X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FT-IR). These results via XPS and FT-IR indicate that the PET surface irradiated with the atmospheric-pressure He plasma jet was oxidized by chemical and/or physical effect due to irradiation of active species.

  5. Discharge effects on gas flow dynamics in a plasma jet

    NASA Astrophysics Data System (ADS)

    Xian, Yu Bin; Hasnain Qaisrani, M.; Yue, Yuan Fu; Lu, Xin Pei

    2016-10-01

    Plasma is used as a flow visualization method to display the gas flow of a plasma jet. Using this method, it is found that a discharge in a plasma jet promotes the transition of the gas flow to turbulence. A discharge at intermediate frequency (˜6 kHz in this paper) has a stronger influence on the gas flow than that at lower or higher frequencies. Also, a higher discharge voltage enhances the transition of the gas flow to turbulence. Analysis reveals that pressure modulation induced both by the periodically directed movement of ionized helium and Ohmic heating on the gas flow plays an important role in inducing the transition of the helium flow regime. In addition, since the modulations induced by the high- and low-frequency discharges are determined by the frequency-selective effect, only intermediate-frequency (˜6 kHz) discharges effectively cause the helium flow transition from the laminar to the turbulent flow. Moreover, a discharge with a higher applied voltage makes a stronger impact on the helium flow because it generates stronger modulations. These conclusions are useful in designing cold plasma jets and plasma torches. Moreover, the relationship between the discharge parameters and the gas flow dynamics is a useful reference on active flow control with plasma actuators.

  6. Off-axis chemical crosstalk in an atmospheric pressure microplasma jet array

    NASA Astrophysics Data System (ADS)

    Sun, P. P.; Chen, H. L.; Park, S.-J.; Eden, J. G.; Liu, D. X.; Kong, M. G.

    2015-10-01

    Developing arrays of parallel microplasma jets is an attractive route to scaling the area available for the treatment of surfaces with low temperature plasma. Increasing the packing density of the arrays may lead to electrical and gas kinetic jet-jet interactions, but previous work has focused almost exclusively on electrostatic coupling between the jets. Chemical interactions (‘crosstalk’) have received considerably less attention. We report here the results of an investigation of chemical crosstalk in 4  ×  4 arrays of microplasma jets, produced in flowing helium at atmospheric pressure. Oxidation damage to an Escherichia coli lawn serves as a diagnostic of the spatial distribution of molecular radicals and other reactive plasma species, produced at the plasma jet/ambient background interface or between the jets, and incident on the surface. Spatial maps of bacterial inactivation by the microplasma jet array for 20 s show the destruction of E. coli at distances as large as 2.7 jet diameter from the nearest plasma perimeter, compared to typically less than 0.5 jet diameter in the single jet case. Extending to 30 s of plasma exposure leads to destruction of the entire bacterial sample. This ‘action at a distance’ effect, the production of long-lived species such as O, O2(a1Δg) and O3 that are responsible for bacterial deactivation, peaks along a line bisecting columns and rows of plasma jets. The data illustrate the synergistic effect of adjacent jets on off-axis formation of reactive species, and show that the chemical and biological impact of an array cannot be inferred from the plasma chemistry of a single jet.

  7. Rapid surface treatment of polyamide 12 by microwave plasma jet

    NASA Astrophysics Data System (ADS)

    Hnilica, J.; Potočňáková, L.; Stupavská, M.; Kudrle, V.

    2014-01-01

    Polyamide 12 (PA 12) films were plasma treated using a microwave surface wave jet at atmospheric pressure. The parameters were the treatment time and the gas composition (argon or argon with admixtures). Moreover, the influence of power modulation was studied. It was found that significant change in wettability is achieved very rapidly, after only 25 ms of treatment. Plasma-induced surface changes are discussed using AFM, ATR-FTIR and XPS results. It is concluded that the increase in wettability is caused by both chemical and morphological changes.

  8. Artificial plasma jet in the ionosphere

    NASA Astrophysics Data System (ADS)

    Haerendel, G.; Sagdeev, R. Z.

    The dynamics of an artificially injected plasma beam in the near-earth space are analyzed in terms of the beam structure, its propagation across the magnetic field, and the resulting wave phenomena (Porcupine Project, flight 4, March 31, 1979). Out of the four ejectable canisters attached to the main payload, two were instrumented by the U.S., one by the USSR (the Xenon plasma beam experiment), and one by West Germany (carrying a barium ion jet experiment). The propagation of the plasma seems to occur in three stages, with high-frequency broad-band oscillations mainly localized in the 'core' of the jet, while low-frequency oscillations were spatially separated from it. The generation region of LF oscillations was found to be much wider than the jet core. As a result of the interaction between the plasma beam and the ambient medium a heating of electrons, up to energies of about 20 eV, associated with LF noise was observed. The behavior of high-energy ions and the observed HF wave phenomena need further analysis.

  9. Laboratory plasma physics experiments using merging supersonic plasma jets

    DOE PAGES

    Hsu, S. C.; Moser, A. L.; Merritt, E. C.; ...

    2015-04-01

    We describe a laboratory plasma physics experiment at Los Alamos National Laboratory that uses two merging supersonic plasma jets formed and launched by pulsed-power-driven railguns. The jets can be formed using any atomic species or mixture available in a compressed-gas bottle and have the following nominal initial parameters at the railgun nozzle exit: ne ≈ ni ~ 10¹⁶ cm⁻³, Te ≈ Ti ≈ 1.4 eV, Vjet ≈ 30–100 km/s, mean chargemore » $$\\bar{Z}$$ ≈ 1, sonic Mach number Ms ≡ Vjet/Cs > 10, jet diameter = 5 cm, and jet length ≈ 20 cm. Experiments to date have focused on the study of merging-jet dynamics and the shocks that form as a result of the interaction, in both collisional and collisionless regimes with respect to the inter-jet classical ion mean free path, and with and without an applied magnetic field. However, many other studies are also possible, as discussed in this paper.« less

  10. Plasma diagnostics of non-equilibrium atmospheric plasma jets

    NASA Astrophysics Data System (ADS)

    Shashurin, Alexey; Scott, David; Keidar, Michael; Shneider, Mikhail

    2014-10-01

    Intensive development and biomedical application of non-equilibrium atmospheric plasma jet (NEAPJ) facilitates rapid growth of the plasma medicine field. The NEAPJ facility utilized at the George Washington University (GWU) demonstrated efficacy for treatment of various cancer types (lung, bladder, breast, head, neck, brain and skin). In this work we review recent advances of the research conducted at GWU concerned with the development of NEAPJ diagnostics including Rayleigh Microwave Scattering setup, method of streamer scattering on DC potential, Rogowski coils, ICCD camera and optical emission spectroscopy. These tools allow conducting temporally-resolved measurements of plasma density, electrical potential, charge and size of the streamer head, electrical currents flowing though the jet, ionization front propagation speed etc. Transient dynamics of plasma and discharge parameters will be considered and physical processes involved in the discharge will be analyzed including streamer breakdown, electrical coupling of the streamer tip with discharge electrodes, factors determining NEAPJ length, cross-sectional shape and propagation path etc.

  11. Inactivation of Candida Strains in Planktonic and Biofilm Forms Using a Direct Current, Atmospheric-Pressure Cold Plasma Micro-Jet

    NASA Astrophysics Data System (ADS)

    Zhu, Wei-Dong; Sun, Peng; Sun, Yi; Yu, Shuang; Wu, Haiyan; Liu, Wei; Zhang, Jue; Fang, Jing

    A direct-current, atmospheric-pressure, He/O2 (2%) cold plasma ­microjet is applied to Candida species (C. glabrata, C. albicansand C. krusei). Effective inactivation is achieved both in air and in water within 5 min of plasma treatment. Same plasma treatment also successfully inactivated candida biofilms on Petri dish. The inactivation was verified by cell viability test (XTT assay). Severe deformation of Candida biofilms after the plasma treatment was observed through scanning electron microscope (SEM). Optical emission spectroscopy shows strong atomic oxygen emission at 777 nm. Hydroxyl radical (•OH), superoxide anion radical (•O2-) and singlet molecular oxygen (1O2) are detected by electron spin resonance (ESR) spectroscopy. The sessile minimal inhibitory concentrations (SMICs) of fluconazole, amphotericin B, and caspofungin against the Candida spp. biofilms were decreased to 2-6 fold dilutions in plasma microjet treated group in comparison with the controls. This novel approach may become a new tool for the treatment of clinical dermatosis

  12. Magnetized plasma jets in experiment and simulation

    NASA Astrophysics Data System (ADS)

    Schrafel, Peter; Greenly, John; Gourdain, Pierre; Seyler, Charles; Blesener, Kate; Kusse, Bruce

    2013-10-01

    This research focuses on the initial ablation phase of a thing (20 micron) Al foil driven on the 1 MA-in-100 ns COBRA through a 5 mm diameter cathode in a radial configuration. In these experiments, ablated surface plasma (ASP) on the top of the foil and a strongly collimated axial plasma jet can be observed developing midway through current-rise. Our goal is to establish the relationship between the ASP and the jet. These jets are of interest for their potential relevance to astrophysical phenomena. An independently pulsed 200 μF capacitor bank with a Helmholtz coil pair allows for the imposition of a slow (150 μs) and strong (~1 T) axial magnetic field on the experiment. Application of this field eliminates significant azimuthal asymmetry in extreme ultraviolet emission of the ASP. This asymmetry is likely a current filamentation instability. Laser-backlit shadowgraphy and interferometry confirm that the jet-hollowing is correlated with the application of the axial magnetic field. Visible spectroscopic measurements show a doppler shift consistent with an azimuthal velocity in the ASP caused by the applied B-field. Computational simulations with the XMHD code PERSEUS qualitatively agree with the experimental results.

  13. Diameter control of gold nanoparticles synthesized in gas phase using atmospheric-pressure H2/Ar plasma jet and gold wire as the nanoparticle source: Control by varying the H2/Ar mixture ratio

    NASA Astrophysics Data System (ADS)

    Shimizu, Yoshiki

    2017-01-01

    This report describes diameter control of gold nanoparticles (AuNPs) during synthesis using an atmospheric-pressure H2/Ar plasma jet drive with pulse-modulated ultrahigh frequency, employing Au wire as the NP source material. During this process, where most of the AuNPs are regarded as formed through condensation from Au vapor derived by the Au wire etching, the mean diameter varied in the approximate range of 2-12 nm with H2 volume ratios up to 3.9%. In plasma diagnostics, results showed that the H2 volume ratio influences the plasma discharge behaviour, which affects the heat flux density flowed into the Au wire, and the atomic hydrogen concentration in the plasma. Both seemed to influence the etching rate of the Au wire per unit area, which is directly related to the concentration of Au vapor in the plasma. The concentration is one factor affecting the particle size evolution because of the collisions among vapor species in reaction field. Therefore, the AuNP size variation with the H2 volume ratio was discussed from the perspective of the etching rate of the Au wire at each H2 volume ratio.

  14. Multiple Pulses from Plasma Jets onto Liquid Covered Tissue

    NASA Astrophysics Data System (ADS)

    Norberg, Seth; Tian, Wei; Johnsen, Eric; Kushner, Mark J.

    2014-10-01

    Atmospheric pressure plasma jets are being studied in the treatment of biological surfaces that are often covered by a thin layer of liquid. The plume of the plasma jet contains neutral radicals and charged species that solvate into the liquid and eventually form terminal species that reach the tissue below. The contribution of neutral and charged species to reactivity in the liquid is sensitive to whether the active plasma plume touches the liquid. In this paper, we discuss results from modeling the production of the aqueous species formed from the interaction of the plume of plasma jets over multiple pulses with the water layer, and the fluences of the species to the underlying tissue. The model used in this study, nonPDPSIM, solves transport equations for charged and neutral species and electron energy, Poisson's equation for the electric potential, and Navier-Stokes equations for the neutral gas flow. Radiation transport includes photoionization of O2 and H2O in the gas and liquid phases and photodissocation of H2Oaq in the liquid. Multiple pulses when the plasma plume touches and does not touch the liquid will be examined. Two regimes of hydrodynamics will be discussed - low repetition rates where the neutral radicals are blown away before the next discharge pulse, and high repetition rate when the plasma plume interacts with neutral radicals from previous pulses. The density of aqueous ions produced in the liquid layer is strongly dependent on whether the plasma effluent touches or does not touch the water surface. Work supported by DOE Office of Fusion Energy Science and NSF.

  15. Thermal behavior of bovine serum albumin after exposure to barrier discharge helium plasma jet

    NASA Astrophysics Data System (ADS)

    Jijie, R.; Pohoata, V.; Topala, I.

    2012-10-01

    Non-thermal plasma jets at atmospheric pressure are useful tools nowadays in plasma medicine. Various applications are tested such as cauterization, coagulation, wound healing, natural and artificial surfaces decontamination, and sterilization. In order to know more about the effects of gas plasma on biological supramolecules, we exposed protein powders to a barrier discharge helium plasma jet. Then, spectroscopic investigations were carried out in order to obtain information on protein secondary, tertiary, and quaternary structures. We obtained a reduction of the protein alpha-helix content after the plasma exposure and a different behavior, for both thermal denaturation/renaturation kinetics and thermal aggregation process.

  16. Atmospheric Pressure Plasmas for Decontamination of Complex Medical Devices

    NASA Astrophysics Data System (ADS)

    Weltmann, Klaus-Dieter; Winter, Jörn; Polak, Martin; Ehlbeck, Jörg; von Woedtke, Thomas

    Atmospheric pressure plasma sources produce a multiplicity of different antimicrobial agents and are applicable to even complicated geometries as well as to heat sensitive materials. Thus, atmospheric pressure plasmas have a huge potential for the decontamination of even complex medical devices like central venous catheters and endoscopes. In this paper we present practicable realizations of atmospheric pressure plasma sources, namely plasma jet, dielectric barrier discharge and microwave driven discharge that are able to penetrate fine lumen or are adaptable to difficult geometries. Furthermore, the antimicrobial efficacy of these sources is given for one example setup in each case.

  17. Study of the expansion characteristics of a pulsed plasma jet in air

    NASA Astrophysics Data System (ADS)

    Xuewei, ZHAO; Yonggang, YU; Shanshan, MANG; Xiaochun, XUE

    2017-04-01

    In the background of electrothermal-chemical (ETC) emission, an investigation has been conducted on the characteristics of a freely expanding pulsed plasma jet in air. The evolutionary process of the plasma jet is experimentally investigated using a piezoelectric pressure sensor and a digital high-speed video system. The variation relation in the extended volume, axial displacement and radial displacement of the pulsed plasma jet in atmosphere with time under different discharge voltages and jet breaking pressures is obtained. Based on experiments, a two-dimensional axisymmetric unsteady model is established to analyze the characteristics of the two-phase interface and the variation of flow-field parameters resulting from a pulsed plasma jet into air at a pressure of 1.5–3.5 MPa under three nozzle diameters (3 mm, 4 mm and 5 mm, respectively). The images of the plasma jet reveal a changing shape process, from a quasi-ellipsoid to a conical head and an elongated cylindrical tail. The axial displacement of the jet is always larger than that along the radial direction. The extended volume reveals a single peak distribution with time. Compared to the experiment, the numerical simulation agrees well with the experimental data. The parameters of the jet field mutate at the nozzle exit with a decrease in the parameter pulse near the nozzle, and become more and more gradual and close to environmental parameters. Increasing the injection pressure and nozzle diameter can increase the parameters of the flow field such as the expansion volume of the pulsed plasma jet, the size of the Mach disk and the pressure. In addition, the turbulent mixing in the expansion process is also enhanced.

  18. Magnetized laboratory plasma jets: experiment and simulation.

    PubMed

    Schrafel, Peter; Bell, Kate; Greenly, John; Seyler, Charles; Kusse, Bruce

    2015-01-01

    Experiments involving radial foils on a 1 MA, 100 ns current driver can be used to study the ablation of thin foils and liners, produce extreme conditions relevant to laboratory astrophysics, and aid in computational code validation. This research focuses on the initial ablation phase of a 20 μm Al foil (8111 alloy), in a radial configuration, driven by Cornell University's COBRA pulsed power generator. In these experiments ablated surface plasma (ASP) on the top side of the foil and a strongly collimated axial plasma jet are observed developing midway through the current rise. With experimental and computational results this work gives a detailed description of the role of the ASP in the formation of the plasma jet with and without an applied axial magnetic field. This ∼1 T field is applied by a Helmholtz-coil pair driven by a slow, 150 μs current pulse and penetrates the load hardware before arrival of the COBRA pulse. Several effects of the applied magnetic field are observed: (1) without the field extreme-ultraviolet emission from the ASP shows considerable azimuthal asymmetry while with the field the ASP develops azimuthal motion that reduces this asymmetry, (2) this azimuthal motion slows the development of the jet when the field is applied, and (3) with the magnetic field the jet becomes less collimated and has a density minimum (hollowing) on the axis. PERSEUS, an XMHD code, has qualitatively and quantitatively reproduced all these experimental observations. The differences between this XMHD and an MHD code without a Hall current and inertial effects are discussed. In addition the PERSEUS results describe effects we were not able to resolve experimentally and suggest a line of future experiments with better diagnostics.

  19. New insights on the propagation of pulsed atmospheric plasma streams: From single jet to multi jet arrays

    SciTech Connect

    Robert, E.; Darny, T.; Dozias, S.; Iseni, S.; Pouvesle, J. M.

    2015-12-15

    Atmospheric pressure plasma propagation inside long dielectric tubes is analyzed for the first time through nonintrusive and nonperturbative time resolved bi-directional electric field (EF) measurements. This study unveils that plasma propagation occurs in a region where longitudinal EF exists ahead the ionization front position usually revealed from plasma emission with ICCD measurement. The ionization front propagation induces the sudden rise of a radial EF component. Both of these EF components have an amplitude of several kV/cm for helium or neon plasmas and are preserved almost constant along a few tens of cm inside a capillary. All these experimental measurements are in excellent agreement with previous model calculations. The key roles of the voltage pulse polarity and of the target nature on the helium flow patterns when plasma jet is emerging in ambient air are documented from Schlieren visualization. The second part of this work is then dedicated to the development of multi jet systems, using two different setups, based on a single plasma source. Plasma splitting in dielectric tubes drilled with sub millimetric orifices, but also plasma transfer across metallic tubes equipped with such orifices are reported and analyzed from ICCD imaging and time resolved EF measurements. This allows for the design and the feasibility validation of plasma jet arrays but also emphasizes the necessity to account for voltage pulse polarity, target potential status, consecutive helium flow modulation, and electrostatic influence between the produced secondary jets.

  20. Ideal hydrodynamic scaling relations for a stagnated imploding spherical plasma liner formed by an array of merging plasma jets

    SciTech Connect

    Cassibry, J. T.; Stanic, M.; Hsu, S. C.

    2013-03-15

    This work presents scaling relations for the peak thermal pressure and stagnation time (over which peak pressure is sustained) for an imploding spherical plasma liner formed by an array of merging plasma jets. Results were derived from three-dimensional (3D) ideal hydrodynamic simulation results obtained using the smoothed particle hydrodynamics code SPHC. The 3D results were compared to equivalent one-dimensional (1D) simulation results. It is found that peak thermal pressure scales linearly with the number of jets and initial jet density and Mach number, quadratically with initial jet radius and velocity, and inversely with the initial jet length and the square of the chamber wall radius. The stagnation time scales approximately as the initial jet length divided by the initial jet velocity. Differences between the 3D and 1D results are attributed to the inclusion of thermal transport, ionization, and perfect symmetry in the 1D simulations. A subset of the results reported here formed the initial design basis for the Plasma Liner Experiment [S. C. Hsu et al., Phys. Plasmas 19, 123514 (2012)].

  1. Decomposition of Chemical Chain Molecules with Atmospheric Pressure Plasma

    NASA Astrophysics Data System (ADS)

    Tansli, Murat; Tasal, Erol

    2016-10-01

    Chemical chain molecules' decomposition is an interesting subject area for the atmospheric pressure plasma applications. The effects of the atmospheric pressure argon plasma on 4-((2-methoxyphenyl)Diazenyl)Benzene-1,3,-Diol molecule at room temperature are investigated. This molecule is one of the industrial dye molecules used widely. When considering the ecological life, this molecule will be very harmful and danger. We suggest a different, easy and useful decomposing method for such molecules. Atmospheric pressure plasma jet was principally treated for this decomposing of the molecule. Fourier transform infrared spectrometry (FT-IR) was used to characterization of the molecule after the plasma application to molecule in liquid phase with ethanol and methanol solvents. The atmospheric-pressure plasma jet of argon (Ar) as non-equilibrium has been formed by ac-power generator with frequency - 24 kHz and voltage - 12 kV. Characterizations for solutions prepared with ethanol and methanol solvents of molecule have been examined after applying (duration: 3 minutes) the atmospheric pressure plasma jet. The molecule was broken at 6C-7N =8N-9C stretching peak after the plasma treatment. The new plasma photo-products for ethanol and methanol solutions were produced as 6C-7N-8N =9C (strong, varying) and 12C =17O (strong, wide) stretching peaks.

  2. Investigation of silicon grain structure and electrical characteristics of TFTs fabricated using different crystallized silicon films by atmospheric pressure micro-thermal-plasma-jet irradiation

    NASA Astrophysics Data System (ADS)

    Hayashi, Shohei; Morisaki, Seiji; Kamikura, Takahiro; Yamamoto, Shogo; Sakaike, Kohei; Akazawa, Muneki; Higashi, Seiichiro

    2014-01-01

    Amorphous silicon (a-Si) films were crystallized using three grain growth modes induced by micro-thermal-plasma-jet (µ-TPJ) irradiation and applied to the channel regions of thin-film transistors (TFTs). Solid phase crystallization (SPC) formed microcrystalline grains and showed a lower crystallinity of 70%, whereas leading wave crystallization (LWC) and high-speed lateral crystallization (HSLC) formed significantly larger grains than the TFT channel region. The SPC-TFT showed a lower field-effect mobility (μFE) due to the small grain size and the existence of many grain boundaries, whereas LWC- and HSLC-TFT channels were formed by only single grains and showed a μFE higher than 300 cm2 V-1 s-1 in the n-channel. The defect density of HSLC was smaller than that of LWC; consequently, the HSLC-TFT performed better than the LWC-TFT. The maximum μFE values of n- and p-channel HSLC-TFTs were 418 and 224 cm2 V-1 s-1, respectively.

  3. Geometry optimization of linear and annular plasma synthetic jet actuators

    NASA Astrophysics Data System (ADS)

    Neretti, G.; Seri, P.; Taglioli, M.; Shaw, A.; Iza, F.; Borghi, C. A.

    2017-01-01

    The electrohydrodynamic (EHD) interaction induced in atmospheric air pressure by a surface dielectric barrier discharge (DBD) actuator has been experimentally investigated. Plasma synthetic jet actuators (PSJAs) are DBD actuators able to induce an air stream perpendicular to the actuator surface. These devices can be used in the field of aerodynamics to prevent or induce flow separation, modify the laminar to turbulent transition inside the boundary layer, and stabilize or mix air flows. They can also be used to enhance indirect plasma treatment effects, increasing the reactive species delivery rate onto surfaces and liquids. This can play a major role in plasma processing and chemical kinetics modelling, where often only diffusive mechanisms are considered. This paper reports on the importance that different electrode geometries can have on the performance of different PSJAs. A series of DBD aerodynamic actuators designed to produce perpendicular jets has been fabricated on two-layer printed circuit boards (PCBs). Both linear and annular geometries were considered, testing different upper electrode distances in the linear case and different diameters in the annular one. An AC voltage supplied at a peak of 11.5 kV and a frequency of 5 kHz was used. Lower electrodes were connected to the ground and buried in epoxy resin to avoid undesired plasma generation on the lower actuator surface. Voltage and current measurements were carried out to evaluate the active power delivered to the discharges. Schlieren imaging allowed the induced jets to be visualized and gave an estimate of their evolution and geometry. Pitot tube measurements were performed to obtain the velocity profiles of the PSJAs and to estimate the mechanical power delivered to the fluid. The optimal values of the inter-electrode distance and diameter were found in order to maximize jet velocity, mechanical power or efficiency. Annular geometries were found to achieve the best performance.

  4. Plasma waves and jets from moving conductors

    NASA Astrophysics Data System (ADS)

    Gralla, Samuel E.; Zimmerman, Peter

    2016-06-01

    We consider force-free plasma waves launched by the motion of conducting material through a magnetic field. We develop a spacetime-covariant formalism for perturbations of a uniform magnetic field and show how the transverse motion of a conducting fluid acts as a source. We show that fast-mode waves are sourced by the compressibility of the fluid, with incompressible fluids launching a pure-Alfvén outflow. Remarkably, this outflow can be written down in closed form for an arbitrary time-dependent, nonaxisymmetric incompressible flow. The instantaneous flow velocity is imprinted on the magnetic field and transmitted away at the speed of light, carrying detailed information about the conducting source at the time of emission. These results can be applied to transients in pulsar outflows and to jets from neutron stars orbiting in the magnetosphere of another compact object. We discuss jets from moving conductors in some detail.

  5. Magnetized and collimated millimeter scale plasma jets with astrophysical relevance

    SciTech Connect

    Brady, Parrish C.; Quevedo, Hernan J.; Valanju, Prashant M.; Bengtson, Roger D.; Ditmire, Todd

    2012-01-15

    Magnetized collimated plasma jets are created in the laboratory to extend our understanding of plasma jet acceleration and collimation mechanisms with particular connection to astrophysical jets. In this study, plasma collimated jets are formed from supersonic unmagnetized flows, mimicking a stellar wind, subject to currents and magnetohydrodynamic forces. It is found that an external poloidal magnetic field, like the ones found anchored to accretion disks, is essential to stabilize the jets against current-driven instabilities. The maximum jet length before instabilities develop is proportional to the field strength and the length threshold agrees well with Kruskal-Shafranov theory. The plasma evolution is modeled qualitatively using MHD theory of current-carrying flux tubes showing that jet acceleration and collimation arise as a result of electromagnetic forces.

  6. [Investigation on the Spectral Characteristics of a Plasma Jet in Atmospheric Argon Glow Discharge].

    PubMed

    Li, Xue-chen; Zhang, Chun-yan; Li, Ji-yuan; Bao, Wen-ting

    2015-12-01

    Plasma jet is a kind of important plasma source at atmospheric pressure. In recent years, it becomes an important hot topic in the field of low temperature plasma. In this paper, using a tungsten needle and a tungsten wire mesh, a direct-current excited jet is developed to operate in argon at atmospheric pressure. In the atmospheric pressure argon, the plasma jet can produce a stable plasma plume. By using the method of emission spectroscopy, the parameters of the plasma plume are investigated. The discharge emits dazzling white light from the area between the tungsten needle electrode and the wire mesh electrode. A plasma plume with a flame shape appears outside the tungsten wire mesh electrode. For a constant value of voltage (U = 13.5 kV), the length of the plasma plume increases with the gas flow rate. For a constant value of the gas flow rate(10 L · min⁻¹), the length of the plasma plume increases with the voltage. The voltage is inversely proportional to the current under the constant gas flow rate. In other words, the voltage decreases with the discharge current, which indicates that a glow discharge is formed in the plasma jet. Optical emission spectrum in 300 to 800 nm is collected from the direct-current excited plasma jet. By Boltzmann plot method, the excited electron temperature of the plasma plume is investigated as a function of the applied voltage or the gas flow rate. Results show that the excited electron temperature increases with decreasing applied voltage under the constant gas flow. Moreover, it increases with decreasing the gas flow under the constant voltage. Based on the discharge theory, these experimental phenomena are explained qualitatively. These results are of great importance to the development of atmospheric pressure uniform discharge plasma source and its application in industrial field.

  7. Disinfection of Staphylococcus Aureus by pulsed non-thermal atmospheric plasma jet

    NASA Astrophysics Data System (ADS)

    Mirpour, Shahriar; Ghoranneviss, Mahmood; Shahgoli, Farhad

    2011-10-01

    The aim of this paper was to study the effect of low-temperature atmospheric plasma jet on non-pathogenic bacteria's colonies. In this regard, Germicidal effect of time and distance of ICP He and He/N2 plasma jet on Staphylococcus Aureus were reported. The gas discharges were generated by a 40 KHz high voltage power supply which led to the inductively coupled plasma. The results showed that He/N2 enhance the sterilization time in comparison of He plasma. To the best of our knowledge this is the first study which has compared the effect of sterilization of ICP Helium and Helium-Nitrogen plasma in listed conditions. Also, the distance dependence showed that the germicidal effect was not linear the distance of electrode and sample. The protein leakage test and SEM of bacteria morphology confirmed the sterilization effect of non-thermal atmospheric pressure plasma jet.

  8. Jet noise control using the dielectric barrier discharge plasma actuators

    NASA Astrophysics Data System (ADS)

    Kopiev, V. F.; Bityurin, V. A.; Belyaev, I. V.; Godin, S. M.; Zaitsev, M. Yu.; Klimov, A. I.; Kopiev, V. A.; Moralev, I. A.; Ostrikov, N. N.

    2012-07-01

    We study experimentally how plasma actuators operating on the basis of surface barrier high-frequency discharge affect jet noise characteristics. The results of investigations of air jets (100-200 m/s) have demonstrated that the studied plasma actuators have control authority over the noise characteristics of these jets. An actuator's effect on the jet in the applied configuration is related to acoustic discharge excitation and to a large extent is similar to the well-known Vlasov-Ginevsky effect. It has been shown that jet excitation in the case of St ˜ 0.5 using the barrier-discharge plasma actuator leads to broadband amplification of jet sound radiation. The jet excitation in the case of St > 2 leads to broadband noise reduction if the action is sufficiently intensive.

  9. Interaction of microwave radiation with an erosion plasma jet

    NASA Astrophysics Data System (ADS)

    Brovkin, V. G.; Pashchina, A. S.; Ryazanskiy, N. M.

    2016-09-01

    The interaction of high-power pulsed microwave radiation with a plasma jet formed by a discharge in an ablative capillary is studied. A significant influence of microwave radiation on the plasma jet flow is found. Depending on the intensity of the initial perturbation of the jet, different scenarios of its evolution downstream are possible: attenuation or amplification accompanied with the development of turbulence up to the disruption of the flow if a certain threshold of the energy action is exceeded. A significant influence of the plasma jet and its state on the spatial position of the microwave energy release zone is found.

  10. Atmospheric-pressure air microplasma jets in aqueous media for the inactivation of Pseudomonas fluorescens cells

    SciTech Connect

    Zhang, Xianhui; Yang, Si-ze; Liu, Dongping; Song, Ying; Sun, Yue

    2013-05-15

    The hollow fiber-based cold air microplasma jet array running at atmospheric pressure has been designed to inactivate Pseudomonas fluorescens (P. fluorescens) cells in vitro in aqueous media. The influences of electrode configurations, air flow rate, and applied voltage on the discharge characteristics of the single microplasma jet operating in aqueous media are presented, and the bactericidal efficiency of the hollow fibers-based and large-volume microplasma jet array is reported. Optical emission spectroscopy is utilized to identify excited species during the antibacterial testing of plasma in solutions. These well-aligned and rather stable air microplasma jets containing a variety of short-lived species, such as OH and O radicals and charged particles, are in direct contact with aqueous media and are very effective in killing P. fluorescens cells in aqueous media. This design shows its potential application for atmospheric pressure air plasma inactivation of bacteria cells in aqueous media.

  11. Inductive and Electrostatic Acceleration in Relativistic Jet-Plasma Interactions

    SciTech Connect

    Ng, Johnny S.T.; Noble, Robert J.; /SLAC

    2005-07-13

    We report on the observation of rapid particle acceleration in numerical simulations of relativistic jet-plasma interactions and discuss the underlying mechanisms. The dynamics of a charge-neutral, narrow, electron-positron jet propagating through an unmagnetized electron-ion plasma was investigated using a three-dimensional, electromagnetic, particle-in-cell computer code. The interaction excited magnetic filamentation as well as electrostatic (longitudinal) plasma instabilities. In some cases, the longitudinal electric fields generated inductively and electrostatically reached the cold plasma wave-breaking limit, and the longitudinal momentum of about half the positrons increased by 50% with a maximum gain exceeding a factor of two. The results are relevant to understanding the micro-physics at the interface region of an astrophysical jet with the interstellar plasma, for example, the edge of a wide jet or the jet-termination point.

  12. Modeling of the merging, liner formation, implosion of hypervelocity plasma jets for the PLX- α project

    NASA Astrophysics Data System (ADS)

    Cassibry, Jason; Hsu, Scott; Schillo, Kevin; Samulyak, Roman; Stoltz, Peter; Beckwith, Kris

    2015-11-01

    A suite of numerical tools will support the conical and 4 π plasma-liner-formation experiments for the PLX- α project. A new Lagrangian particles (LP) method will provide detailed studies of the merging of plasma jets and plasma-liner formation/convergence. A 3d smooth particle hydrodynamic (SPH) code will simulate conical (up to 9 jets) and 4 π spherical (up to 60 jets) liner formation and implosion. Both LP and SPH will use the same tabular EOS generated by Propaceos, thermal conductivity, optically thin radiation and physical viscosity models. With LP and SPH,the major objectives are to study Mach-number degradation during jet merging, provide RMS amplitude and wave number of the liner nonuniformity at the leading edge, and develop scaling laws for ram pressure and liner uniformity as a function of jet parameters. USIM, a 3D multi-fluid plasma code, will be used to perform 1D and 2D simulations of plasma-jet-driven magneto-inertial fusion (PJMIF) to identify initial conditions in which the ``liner gain'' exceeds unity. A brief overview of the modeling program will be provided. Results from SPH modeling to support the PLX- α experimental design will also be presented, including preliminary ram-pressure scaling and non-uniformity characterization.

  13. Plasma Jet Simulations Using a Generalized Ohm's Law

    NASA Technical Reports Server (NTRS)

    Ebersohn, Frans; Shebalin, John V.; Girimaji, Sharath S.

    2012-01-01

    Plasma jets are important physical phenomena in astrophysics and plasma propulsion devices. A currently proposed dual jet plasma propulsion device to be used for ISS experiments strongly resembles a coronal loop and further draws a parallel between these physical systems [1]. To study plasma jets we use numerical methods that solve the compressible MHD equations using the generalized Ohm s law [2]. Here, we will discuss the crucial underlying physics of these systems along with the numerical procedures we utilize to study them. Recent results from our numerical experiments will be presented and discussed.

  14. Stimulation of wound healing by helium atmospheric pressure plasma treatment

    NASA Astrophysics Data System (ADS)

    Vasile Nastuta, Andrei; Topala, Ionut; Grigoras, Constantin; Pohoata, Valentin; Popa, Gheorghe

    2011-03-01

    New experiments using atmospheric pressure plasma have found large application in treatment of living cells or tissues, wound healing, cancerous cell apoptosis, blood coagulation on wounds, bone tissue modification, sterilization and decontamination. In this study an atmospheric pressure plasma jet generated using a cylindrical dielectric-barrier discharge was applied for treatment of burned wounds on Wistar rats' skin. The low temperature plasma jet works in helium and is driven by high voltage pulses. Oxygen and nitrogen based impurities are identified in the jet by emission spectroscopy. This paper analyses the natural epithelization of the rats' skin wounds and two methods of assisted epithelization, a classical one using polyurethane wound dressing and a new one using daily atmospheric pressure plasma treatment of wounds. Systemic and local medical data, such as haematological, biochemical and histological parameters, were monitored during entire period of study. Increased oxidative stress was observed for plasma treated wound. This result can be related to the presence in the plasma volume of active species, such as O and OH radicals. Both methods, wound dressing and plasma-assisted epithelization, provided positive medical results related to the recovery process of burned wounds. The dynamics of the skin regeneration process was modified: the epidermis re-epitelization was accelerated, while the recovery of superficial dermis was slowed down.

  15. Numerical and experimental study on a pulsed-dc plasma jet

    NASA Astrophysics Data System (ADS)

    Liu, X. Y.; Pei, X. K.; Lu, X. P.; Liu, D. W.

    2014-06-01

    A numerical and experimental study of plasma jet propagation in a low-temperature, atmospheric-pressure, helium jet in ambient air is presented. A self-consistent, multi-species, two-dimensional axially symmetric plasma model with detailed finite-rate chemistry of helium-air mixture composition is used to provide insights into the propagation of the plasma jet. The obtained simulation results suggest that the sheath forms near the dielectric tube inner surface and shields the plasma channel from the tube surface. The strong electric field at the edge of the dielectric field enhances the ionization in the air mixing layer; therefore, the streamer head becomes ring-shaped when the streamer runs out of the tube. The avalanche-to-streamer transition is the main mechanism of streamer advancement. Penning ionization dominates the ionization reactions and increases the electrical conductivity of the plasma channel. The simulation results are supported by experimental observations under similar discharge conditions.

  16. Probing Runaway Electrons with Nanoparticle Plasma Jet

    NASA Astrophysics Data System (ADS)

    Bogatu, I. N.; Thompson, J. R.; Galkin, S. A.; Kim, J. S.

    2014-10-01

    The injection of C60/C nanoparticle plasma jet (NPPJ) into tokamak plasma during a major disruption has the potential to probe the runaway electrons (REs) during different phases of their dynamics and diagnose them through spectroscopy of C ions visible/UV lines. A C60/C NPPJ of ~75 mg, high-density (>1023 m-3), hyper-velocity (>4 km/s), and uniquely fast response-to-delivery time (~1 ms) has been demonstrated on a test bed. It can rapidly and deeply deliver enough mass to increase electron density to ~2.4 × 1021 m-3, ~60 times larger than typical DIII-D pre-disruption value. We will present the results of our investigations on: 1) C60 fragmentation and gradual release of C atoms along C60 NPPJ penetration path through the RE carrying residual cold plasma, 2) estimation of photon emissivity coefficient for the lines of the C ions, and 3) simulation of C60/C PJ penetration to the RE beam location in equivalent conditions to the characteristic ~1 T B-field of DIII-D. The capabilities of this injection technique provide a unique possibility in understanding and controlling the RE beam, which is a critical problem for ITER. Work supported by US DOE DE-SC0011864 Grant.

  17. Experimental studies of collisional plasma shocks and plasma interpenetration via merging supersonic plasma jets

    NASA Astrophysics Data System (ADS)

    Hsu, S. C.; Moser, A. L.; Merritt, E. C.; Adams, C. S.

    2015-11-01

    Over the past 4 years on the Plasma Liner Experiment (PLX) at LANL, we have studied obliquely and head-on-merging supersonic plasma jets of an argon/impurity or hydrogen/impurity mixture. The jets are formed/launched by pulsed-power-driven railguns. In successive experimental campaigns, we characterized the (a) evolution of plasma parameters of a single plasma jet as it propagated up to ~ 1 m away from the railgun nozzle, (b) density profiles and 2D morphology of the stagnation layer and oblique shocks that formed between obliquely merging jets, and (c) collisionless interpenetration transitioning to collisional stagnation between head-on-merging jets. Key plasma diagnostics included a fast-framing CCD camera, an 8-chord visible interferometer, a survey spectrometer, and a photodiode array. This talk summarizes the primary results mentioned above, and highlights analyses of inferred post-shock temperatures based on observations of density gradients that we attribute to shock-layer thickness. We also briefly describe more recent PLX experiments on Rayleigh-Taylor-instability evolution with magnetic and viscous effects, and potential future collisionless shock experiments enabled by low-impurity, higher-velocity plasma jets formed by contoured-gap coaxial guns. Supported by DOE Fusion Energy Sciences and LANL LDRD.

  18. Analytic model and frequency characteristics of plasma synthetic jet actuator

    NASA Astrophysics Data System (ADS)

    Zong, Hao-hua; Wu, Yun; Li, Ying-hong; Song, Hui-min; Zhang, Zhi-bo; Jia, Min

    2015-02-01

    This paper reports a novel analytic model of a plasma synthetic jet actuator (PSJA), considering both the heat transfer effect and the inertia of the throat gas. Both the whole cycle characteristics and the repetitive working process of PSJA can be predicted with this model. The frequency characteristics of a PSJA with 87 mm3 volume and different orifice diameters are investigated based on the analytic model combined with experiments. In the repetitive working mode, the actuator works initially in the transitional stage with 20 cycles and then in the dynamic balanced stage. During the transitional stage, major performance parameters of PSJA experience stepped growth, while during the dynamic balanced stage, these parameters are characterized by periodic variation. With a constant discharge energy of 6.9 mJ, there exists a saturated frequency of 4 kHz/6 kHz for an orifice diameter of 1 mm/1.5 mm, at which the time-averaged total pressure of the pulsed jet reaches a maximum. Between 0.5 mm and 1.5 mm, a larger orifice diameter leads to a higher saturated frequency due to the reduced jet duration time. As the actuation frequency increases, both the time-averaged cavity temperature and the peak jet velocity initially increase and then remain almost unchanged at 1600 K and 280 m/s, respectively. Besides, with increasing frequency, the mechanical energy incorporated in single pulsed jet, the expelled mass per pulse, and the time-averaged density in the cavity, decline in a stair stepping way, which is caused by the intermittent decrease of refresh stage duration in one period.

  19. Influence of Ar/O2/H2O Feed Gas and N2/O2/H2O Environment on the Interaction of Time Modulated MHz Atmospheric Pressure Plasma Jet (APPJ) with Model Polymers

    NASA Astrophysics Data System (ADS)

    Oehrlein, Gottlieb; Luan, Pingshan; Knoll, Andrew; Kondeti, Santosh; Bruggeman, Peter

    2016-09-01

    An Ar/O2/H2O fed time modulated MHz atmospheric pressure plasma jet (APPJ) in a sealed chamber was used to study plasma interaction with model polymers (polystyrene, poly-methyl methacrylate, etc.). The amount of H2O in the feed gas and/or present in the N2, O2, or N2/O2 environment was controlled. Short lived species such as O atoms and OH radicals play a crucial role in polymer etching and surface modifications (obtained from X-ray photoelectron spectroscopy of treated polymers without additional atmospheric exposure). Polymer etching depth for Ar/air fed APPJ mirrors the decay of gas phase O atoms with distance from the APPJ nozzle in air and is consistent with the estimated O atom flux at the polymer surface. Furthermore, whereas separate O2 or H2O admixture to Ar enhances polymer etching, simultaneous addition of O2 and H2O to Ar quenches polymer etching. This can be explained by the mutual quenching of O with OH, H and HO2 in the gas phase. Results where O2 and/or H2O in the environment were varied are consistent with these mechanisms. All results will be compared with measured and simulated species densities reported in the literature. We gratefully acknowledge funding from US Department of Energy (DE-SC0001939) and National Science Foundation (PHY-1415353).

  20. observation of auroral emissions induced by artificial plasma jets

    NASA Astrophysics Data System (ADS)

    Erlandson, R. E.; Swaminathan, P. K.; Meng, C.-I.; Stoyanov, B. J.; Zetzer, J. I.; Gavrilov, B. G.; Kiselev, Yu. N.; Romanovsky, Yu. A.

    In this paper we present ultraviolet to near infrared spectrographic observations of high-speed artificial plasma jet interactions with the ionosphere. The plasma jets were injected quasi-parallel to the magnetic field at an altitude of 140 km during the Fluxus-1 and -2 experiments. The jets contained aluminum ions and were generated using a shaped-charge device known as an Explosive Type Generator (ETG). Satellite-based spectrographic observations of the plasma jet show typical auroral emission features associated with electron impact excitation. The auroral features include emission at 135.6 nm (OI) and 557.7 nm (OI). The 135.6 nm emission was prompt while the 557.7 nm was observed for 5 seconds. The most likely source of these auroral emissions are ionospheric and magnetospheric electrons that neutralize the plasma jet.

  1. Temperature measurement of an atmospheric pressure arc discharge plasma jet using the diatomic CN (B {sup 2}{sigma}{sup +}-X {sup 2}{sigma}{sup +}, violet system) molecular spectra

    SciTech Connect

    Moon, Se Youn; Kim, D. B.; Gweon, B.; Choe, W.

    2009-03-01

    The CN (B {sup 2}{sigma}{sup +}-X {sup 2}{sigma}{sup +}) molecular emission spectrum is used to measure both the vibrational and rotational temperatures in atmospheric pressure arc jet discharges. The vibrational and rotational temperature effects on the synthetic diatomic molecular spectra were investigated from the (v{sup '},v{sup ''})=(0,0) band to the (5,5) band. The temperatures obtained from the synthetic spectra compared with the experimental result of a low-frequency arc discharge show a vibrational temperature of (4250-5010) K and a rotational temperature of (3760-3980) K for the input power in the range of (80-280) W. As the (0,0) band is isolated from other vibrational transition bands, determination of the rotational temperature is possible based only on the (0,0) band, which simplifies the temperature measurement. From the result, it was found that the CN molecular spectrum can be used as a thermometer for atmospheric pressure plasmas containing carbon and nitrogen.

  2. Plasma jet printing for flexible substrates

    NASA Astrophysics Data System (ADS)

    Gandhiraman, Ram P.; Singh, Eric; Diaz-Cartagena, Diana C.; Nordlund, Dennis; Koehne, Jessica; Meyyappan, M.

    2016-03-01

    Recent interest in flexible electronics and wearable devices has created a demand for fast and highly repeatable printing processes suitable for device manufacturing. Robust printing technology is critical for the integration of sensors and other devices on flexible substrates such as paper and textile. An atmospheric pressure plasma-based printing process has been developed to deposit different types of nanomaterials on flexible substrates. Multiwalled carbon nanotubes were deposited on paper to demonstrate site-selective deposition as well as direct printing without any type of patterning. Plasma-printed nanotubes were compared with non-plasma-printed samples under similar gas flow and other experimental conditions and found to be denser with higher conductivity. The utility of the nanotubes on the paper substrate as a biosensor and chemical sensor was demonstrated by the detection of dopamine, a neurotransmitter, and ammonia, respectively.

  3. Three-dimensional MHD simulation of the Caltech plasma jet experiment: first results

    SciTech Connect

    Zhai, Xiang; Bellan, Paul M.; Li, Hui; Li, Shengtai E-mail: pbellan@caltech.edu E-mail: sli@lanl.gov

    2014-08-10

    Magnetic fields are believed to play an essential role in astrophysical jets with observations suggesting the presence of helical magnetic fields. Here, we present three-dimensional (3D) ideal MHD simulations of the Caltech plasma jet experiment using a magnetic tower scenario as the baseline model. Magnetic fields consist of an initially localized dipole-like poloidal component and a toroidal component that is continuously being injected into the domain. This flux injection mimics the poloidal currents driven by the anode-cathode voltage drop in the experiment. The injected toroidal field stretches the poloidal fields to large distances, while forming a collimated jet along with several other key features. Detailed comparisons between 3D MHD simulations and experimental measurements provide a comprehensive description of the interplay among magnetic force, pressure, and flow effects. In particular, we delineate both the jet structure and the transition process that converts the injected magnetic energy to other forms. With suitably chosen parameters that are derived from experiments, the jet in the simulation agrees quantitatively with the experimental jet in terms of magnetic/kinetic/inertial energy, total poloidal current, voltage, jet radius, and jet propagation velocity. Specifically, the jet velocity in the simulation is proportional to the poloidal current divided by the square root of the jet density, in agreement with both the experiment and analytical theory. This work provides a new and quantitative method for relating experiments, numerical simulations, and astrophysical observation, and demonstrates the possibility of using terrestrial laboratory experiments to study astrophysical jets.

  4. Ion-viscosity effects on plasma-liner formation and implosion via merging supersonic plasma jets

    NASA Astrophysics Data System (ADS)

    Schillo, Kevin; Cassibry, Jason; Samulyak, Roman; Shih, Wen; Hsu, Scott; PLX-Alpha Team

    2016-10-01

    The PLX- α project endeavors to study plasma-liner formation and implosion by merging a spherical array of plasma jets as a candidate standoff driver for MIF. Smoothed particle hydrodynamics is used to model the liner formation and implosion processes. SPH is a meshless Lagrangian method to simulate fluid flows by dividing a fluid into a set of particles and using a summation interpolant function to calculate the properties and gradients for each of these particles. Ion viscosity is anticipated to be an important mechanism for momentum transport during liner formation, implosion, and stagnation. To study this, ion viscosity was incorporated into the code. To provide confidence in the numerical output and to help identify the difference between numerical and physical diffusion, a series of test cases were performed, consisting of Couette flow, Gresho vortex, and a Taylor-Green vortex. An L2-norm analysis was performed to measure the error and convergence. Simulations of conical (6 jets) and 4 π (60 jets) liners with and without ion viscosity reveal potential effects of viscosity on ram pressure, Mach-number degradation, and evolution of liner perturbations during jet merging and liner implosion.

  5. Supersonic gas jets for laser-plasma experiments.

    PubMed

    Schmid, K; Veisz, L

    2012-05-01

    We present an in-depth analysis of De Laval nozzles, which are ideal for gas jet generation in a wide variety of experiments. Scaling behavior of parameters especially relevant to laser-plasma experiments as jet collimation, sharpness of the jet edges and Mach number of the resulting jet is studied and several scaling laws are given. Special attention is paid to the problem of the generation of microscopic supersonic jets with diameters as small as 150 μm. In this regime, boundary layers dominate the flow formation and have to be included in the analysis.

  6. Plasma Jet Interaction with Thomson Scattering Probe Laser

    NASA Astrophysics Data System (ADS)

    Byvank, Tom; Banasek, Jacob; Potter, William; Kusse, Bruce

    2016-10-01

    Thomson scattering systems can diagnose plasma temperatures and velocities. When probing a plasma jet with the Thomson scattering laser, we observe a laser-plasma interaction that inputs energy into the plasma jet. The absorbed energy causes a bubble of low density ( 5*1017 cm-2) in the jet (unperturbed 1018 cm-2). A pulsed power machine (1 MA peak current, 100 ns rise time) with a radial foil (15 μm thick Al) configuration generates the plasma jet. We compare the effects of using 10 J and 1 J laser energies, for which the 10 J laser is a larger perturbation. We discuss how the interaction affects the Thomson scattering temperature and velocity measurements. Work supported by National Nuclear Security Administration (NNSA) Stewardship Sciences Academic Programs under Department of Energy (DOE) Cooperative Agreement DE-NA0001836 and National Science Foundation (NSF) Grant PHY-1102471.

  7. RF atmospheric plasma jet surface treatment of paper

    NASA Astrophysics Data System (ADS)

    Pawlat, Joanna; Terebun, Piotr; Kwiatkowski, Michał; Diatczyk, Jaroslaw

    2016-09-01

    A radio frequency RF atmospheric pressure plasma jet was used to enhance the wettability of cellulose-based paper of 90 g m-2 and 160 g m-2 grammage as a perspective platform for antibiotic sensitivity tests. Helium and argon were the carrier gases for oxygen and nitrogen; pure water and rapeseed oil were used for goniometric tests. The influence of the flow rate and gas type, the power of the discharge, and distance from the nozzle was examined. The surface structure was observed using an optical microscope. Attenuated total reflection Fourier transform infrared (ATR-FTIR) spectra were investigated in order to determine whether cellulose degradation processes occurred. The RF plasma jet allowed us to decrease the surface contact angle without drastic changes in other features of the tested material. Experiments confirmed the significant influence of the distance between the treated sample and reactor nozzle, especially for treatment times longer than 15 s due to the greater concentration of reactive species at the surface of the sample, which decreases with distance—and their accumulation effect with time. The increase of discharge power plays an important role in decreasing the surface contact angle for times longer than 10 s. Higher power had a positive effect on the amount of generated active particles and facilitated the ignition of discharge. However, a too high value can cause a rise in temperature of the material and heat-caused damage.

  8. Friction and wear properties of Ti6Al4V/WC-Co in cold atmospheric plasma jet

    NASA Astrophysics Data System (ADS)

    Xu, Wenji; Liu, Xin; Song, Jinlong; Wu, Libo; Sun, Jing

    2012-10-01

    The friction and wear properties of Ti6Al4V/WC-Co friction pair were studied using an autonomous atmospheric pressure bare electrode cold plasma jet generating device and block-on-ring friction/wear tester, respectively. The study was conducted under air, air jet, nitrogen jet, air cold plasma jet, and nitrogen cold plasma jet atmospheres. Both nitrogen cold and air cold plasma jets effectively reduced the friction coefficients of the friction pairs and decreased friction temperature. The friction coefficient in the nitrogen cold plasma jet decreased to almost 60% compared with that in the air. The scanning electron microscope, energy-dispersive X-ray spectroscope, and X-ray diffraction analyses illustrated that adhesive wear was relieved and the friction surfaces of Ti6Al4V were smoother, both in the nitrogen cold and air cold plasma jets. The roughness value Ra of the Ti6Al4V friction surfaces can reach 1.107 μm. A large number of nitrogen particles in the ionic and excited states contained by cold plasma jets reacts easily on the friction surface to produce a large amount of nitrides, which can excellently reduce the wear of Ti6Al4V/WC-Co friction pairs in real-time.

  9. Removal of floating dust in glow discharge using plasma jet

    SciTech Connect

    Ticos, C. M.; Jepu, I.; Lungu, C. P.; Chiru, P.; Zaroschi, V.; Lungu, A. M.

    2010-07-05

    Dust can be an inconvenient source of impurities in plasma processing reactors and in many cases it can cause damage to the plasma-treated surfaces. A technique for dust expulsion out of the trapping region in plasma is presented here, based on the wind force exerted on dust particles by a pulsed plasma jet. Its applicability is demonstrated by removing floating dust in the sheath of parallel-plate capacitive radio-frequency plasma.

  10. Plasma-polymerized methyl methacrylate via intense and highly energetic atmospheric pressure micro-plasma for bio-medical applications

    NASA Astrophysics Data System (ADS)

    Park, Choon-Sang; Ballato, John; Kim, Sung-O.; Clemson University Team

    2013-09-01

    Poly (methyl methacrylate), PMMA, has been widely used as a biocompatible material in bone cement, dental fillings, and many other bio-related applications. Vacuum plasmas and radio frequency (RF) atmospheric plasmas are the most common methods for depositing plasma-derived thin films and nanoparticles. However, the necessary equipment is difficult to operate and maintain as well as being large and expensive. Here, we report the use of a novel intense and highly energetic atmospheric pressure plasma jet array using direct plasma jet-to-jet coupling effects to deposit high quality plasma-polymerized MMA (PPMMA) for bio-medical applications. The newly proposed atmospheric pressure micro-plasma jet array device can generate the intense plasma mode with a strong plasma emission and high plasma particle energy. PPMMA was successfully deposited on a variety of substrates and characterized by SEM, AFM, and FT-IR. The micro-plasma jet is obtained at a sinusoidal voltage with a peak value of 30 kV and frequency of 35 kHz. Argon gas was employed as the discharge gas for plasma generation and its flow rate was in the range of 2230 sccm, Methyl methacrylate (MMA) monomer was vaporized by means of a glass bubbler which was supplied by argon gas with flow rates in the range of 268 sccm from room temperature to 400°C. The deposited PPMMA thin films were flexible, transparent, thin, and strong on metal substrates.

  11. Destruction of {alpha}-synuclein based amyloid fibrils by a low temperature plasma jet

    SciTech Connect

    Karakas, Erdinc; Laroussi, Mounir; Munyanyi, Agatha; Greene, Lesley

    2010-10-04

    Amyloid fibrils are ordered beta-sheet aggregates that are associated with a number of neurodegenerative diseases such as Alzheimer and Parkinson. At present, there is no cure for these progressive and debilitating diseases. Here we report initial studies that indicate that low temperature atmospheric pressure plasma can break amyloid fibrils into smaller units in vitro. The plasma was generated by the 'plasma pencil', a device capable of emitting a long, low temperature plasma plume/jet. This avenue of research may facilitate the development of a plasma-based medical treatment.

  12. Destruction of α-synuclein based amyloid fibrils by a low temperature plasma jet

    NASA Astrophysics Data System (ADS)

    Karakas, Erdinc; Munyanyi, Agatha; Greene, Lesley; Laroussi, Mounir

    2010-10-01

    Amyloid fibrils are ordered beta-sheet aggregates that are associated with a number of neurodegenerative diseases such as Alzheimer and Parkinson. At present, there is no cure for these progressive and debilitating diseases. Here we report initial studies that indicate that low temperature atmospheric pressure plasma can break amyloid fibrils into smaller units in vitro. The plasma was generated by the "plasma pencil," a device capable of emitting a long, low temperature plasma plume/jet. This avenue of research may facilitate the development of a plasma-based medical treatment.

  13. Numerical simulation of a dual-source supersonic plasma jet expansion process: continuum approach

    NASA Astrophysics Data System (ADS)

    Pal, Subrata; Dey, Subhrajit; Miebach, Thomas

    2007-05-01

    Expanding thermal plasma (ETP) is a versatile technology for thin film deposition process with directional plasma flux and high deposition rates. This process involves expansion of supersonic plasma jets through a steep pressure ratio into a chamber maintained at near vacuum. Usually the plasma jets deviate from chemical and thermal equilibrium and the continuum approach is insufficient to describe the phenomena. In the current work, the continuum approach based Navier-Stokes equations have been implemented to study and understand the jet expansion process in a typical dual-arc plasma deposition reactor. The numerical predictions have been compared against in-house experimental data obtained by thermocouple measurements. For the range of back pressures (6-200 Pa) considered, it was observed that the jet core is supersonic and transitions to a subsonic zone downstream without the formation of any Mach disc for the prevalent operating parameters. Indications of thick and smeared barrel shocks were however observed in the computed flow-thermal fields. The modelled fluid was assumed to be a perfect gas with temperature dependent specific heats, thermal conductivity and viscosity coefficients, with constant Prandtl number of order unity. The radial spreads of the jets increase with increasing pressure ratio thus leading to enhanced interactions within reduced distances downstream of the nozzle exit. The jet core Mach number also increases, but moderately, with decreasing backpressure. It is concluded that within reasonable accuracy, continuum approach based calculations are able to capture most of the important phenomena involved in compressible, high-temperature, supersonic jet expansion processes which are essential in designing chambers relevant to the mentioned processes.

  14. Plasma Jet Simulations Using a Generalized Ohm's Law

    NASA Astrophysics Data System (ADS)

    Ebersohn, F.; Shebalin, J. V.; Girimaji, S. S.

    2012-12-01

    Plasma jets are important physical phenomena in astrophysics and plasma propulsion devices. A currently proposed dual jet plasma propulsion device to be used for ISS experiments strongly resembles a coronal loop and further draws a parallel between these physical systems [1]. To study plasma jets we use numerical methods which solve the compressible MHD equations using the generalized Ohm's law[2]. Herein we discuss the crucial underlying physics of these systems along with the numerical procedures we utilize to study them. Recent results from our numerical experiments will be presented and discussed. [1] T. Glover, et al., The VASIMR® VF-200-1 ISS Experiment as a Laboratory for Astrophysics, Poster SM51C-1831, AGU Fall Meeting, San Francisco, December 13-17, 2010. [2] F. Ebersohn, J. V Shebalin, S. Girimaji and D. Staack, Magnetic Field Effects on Plasma Plumes, Paper O2-404, 39th EPS Conference on Plasma Physics, Stockholm, July 2-6, 2012.;

  15. The effect of working gas impurities on plasma jets

    SciTech Connect

    Liu, X. Y.; He, M. B.; Liu, D. W.

    2015-04-15

    Air intrusion reduced the purity of working gas inside the tube for plasma jet, and thereby, affected the discharge dynamics. In this paper, the effect of using working gas with different purity level (helium purity 99.99999%, 99.99%, 99.9%, and 99%) on photoionization and the chemical reactivity of plasma jet were studied using a 2 dimensional plasma jet model. Photoionization of air species acted as a source of pre-ionization in front of the ionization region, which facilitated the transition from localized discharge to streamers inside the tube. The density of reactive species inside the tube was found to increase with the concentration of working gas impurities. For the highest purity helium (99.99999%), despite a low photoionization rate and the distance between the photoionization region and ionization region inside the tube, by increasing the applied voltage and decreasing the distance between the electrode and nozzle, plasma jets were formed.

  16. Model of the plasma jet originating from a cathode spot

    SciTech Connect

    Gavrilov, V.N.; Litvinov, E.A.; Mesyats, G.A.

    1995-12-31

    The 2-D NM model of the vacuum-arc plasma jet presented here is in outgrowth of the 1-D hydrodynamic model discussed by us. The computation carried out in 1-D approximation have provided the principal characteristics of a cathode jet being in satisfactory agreement with experimental data. Nevertheless, there results cannot be considered completely adequate, since actually the plum parameters of a cathode jet are distributed highly nonuniformly over its cross section. Furthermore, a 1-D model falls to take in to account the effects related to the influence of the self-magnetic field of the cathode jet.

  17. Physics of Coanda jet detachment at high-pressure ratio

    NASA Astrophysics Data System (ADS)

    Cornelius, Kenneth C.; Lucius, Gerald A.

    1994-05-01

    Experimental measurements of surface pressure for an underexpanded two-dimensional supersonic Coanda flow with static conditions exterior to the jet flow was obtained for a fixed slot height to a radius ratio of 0.04. The data demonstrate that an oblique shock forms near the jet exit plane which vectors the jet flow from the curved surface at a pressure ratio of 7.6. The jet detachment occurs at a pressure ratio which is a function of the ratio of slot height to cylinder radius. An increase in the pressure ratio to 11.5 before jet detachment has been demonstrated by the translation of the upper wall providing for a converging-diverging geometry. The physics of the Coanda expansion and the jet detachment are qualitatively described using an optical schlieren system. A compressible inviscid model was derived analytically to demonstrate the variation in Mach number and surface pressure as a function of the geometric parameters with increasing pressure ratio.

  18. Temperature measurement of cryogenic nitrogen jets at supercritical pressure

    NASA Astrophysics Data System (ADS)

    Tani, H.; Teramoto, S.; Toki, T.; Yoshida, S.; Yamaguchi, K.; Okamoto, K.

    2016-07-01

    The temperatures of transcritical and supercritical nitrogen jets were measured to explore the influence of "pseudovaporization" upon cryogenic propellant mixing in high-pressure rocket chambers. Pseudovaporization is the large thermodynamic transition near the pseudocritical temperature under transcritical conditions, which can include a drastic density change and large peak of isobaric specific heat. A decline in the rise of temperature along the jet centerline of the transcritical jet was caused at the position where the local temperature reached nearpseudocritical temperature. This can be considered to be due to the large peak of isobaric specific heat. The density jump appeared near the pseudocritical temperature, which can be correlated to the sudden expansion due to pseudovaporization. The axial profiles of the temperature and density of the supercritical jet monotonically increased and decreased, respectively, in the downstream region of the end of the jet potential core. Similar to the axial profiles, the radial profiles of the temperature were influenced by the pseudovaporization - i. e., the temperature rise in the radial direction became very shallow in the region where the local temperature was still lower than the pseudocritical temperature. The full width at half maximum of the density profiles stayed almost constant further downstream of the end of the jet potential core, whereas that of the mass fraction profiles of the incompressible variable-density jet began to increase near the end of the potential core. Hence, the evolutions of jet mixing layers of transcritical jets and variable-density jets can be considered to differ due to pseudovaporization.

  19. Stability of liquid-nitrogen-jet laser-plasma targets

    SciTech Connect

    Fogelqvist, E. Kördel, M.; Selin, M.; Hertz, H. M.

    2015-11-07

    Microscopic jets of cryogenic substances such as liquid nitrogen are important regenerative high-density targets for high-repetition rate, high-brightness laser-plasma soft x-ray sources. When operated in vacuum such liquid jets exhibit several non-classical instabilities that negatively influence the x-ray source's spatial and temporal stability, yield, and brightness, parameters that all are important for applications such as water-window microscopy. In the present paper, we investigate liquid-nitrogen jets with a flash-illumination imaging system that allows for a quantitative stability analysis with high spatial and temporal resolution. Direct and indirect consequences of evaporation are identified as the key reasons for the observed instabilities. Operating the jets in an approximately 100 mbar ambient atmosphere counteracts the effects of evaporation and produces highly stable liquid nitrogen jets. For operation in vacuum, which is necessary for the laser plasmas, we improve the stability by introducing an external radiative heating element. The method significantly extends the distance from the nozzle that can be used for liquid-jet laser plasmas, which is of importance for high-average-power applications. Finally, we show that laser-plasma operation with the heating-element-stabilized jet shows improved short-term and long-term temporal stability in its water-window x-ray emission.

  20. Radio jet refraction in galactic atmospheres with static pressure gradients

    NASA Technical Reports Server (NTRS)

    Henriksen, R. N.; Vallee, J. P.; Bridle, A. H.

    1981-01-01

    A theory of double radio sources which have a 'Z' or 'S' morphology is proposed, based on the refraction of radio jets in the extended atmosphere of an elliptical galaxy. The model describes a collimated jet of supersonic material bending self-consistently under the influence of external static pressure gradients. Gravity and magnetic fields are neglected in the simplest case except insofar as they determine the static pressure distribution. The calculation is a straightforward extension of a method used to calculate a ram-pressure model for twin radio trails ('C' morphology). It may also be described as a continuous-jet version of a buoyancy model proposed in 1973. The model has the added virtue of invoking a galactic atmosphere similar to those already indicated by X-ray measurements of some other radio galaxies and by models for the collimation of other radio jets.

  1. Characteristics of a Plasma Torch Designed for Very Low Pressure Plasma Spraying

    NASA Astrophysics Data System (ADS)

    Gao, Yang; Yang, De Ming; Gao, Jianyi

    2012-06-01

    Unlike atmosphere plasma spraying (APS), very low pressure plasma spraying (VLPPS) can only weakly heat the feed materials at the plasma-free region exit of the nozzle. Most current VLPPS methods have adopted a high power plasma gun, which operates at high arc currents up to 2500 A to remedy the lower heating ability, causing a series of problems for both the plasma torch and the associated facility. According to the Kundsen number and pressures distribution inside of the nozzle in a low-pressure environment, a plasma torch was designed with a separated anode and nozzle, and with the powder feed to the plasma jets inside the nozzle intake. In this study, the pressures in the plasma gas intake, in the nozzle intake and outside the plasma torch were measured using an enthalpy probe. For practice, SUS 316 stainless steel coatings were prepared at the plasma currents of 500-600 A, an arc voltage of 50 V and a chamber pressure of 1000 Pa; the results indicated that coatings with an equiaxed microstructure could be deposited in proper conditions.

  2. Gas Flow and Electric Field Characterization in Plasma Jets for Biomedical Applications: From Single Jet to Multi Jet Arrays

    NASA Astrophysics Data System (ADS)

    Robert, Eric

    2015-09-01

    This work reports first on time-resolved measurement of longitudinal and radial electric fields (EF) associated with plasma propagation in dielectric capillaries. Plasma propagation occurs in a region where longitudinal EF exists ahead the ionization front position revealed from plasma emission with ICCD measurement. The ionization front propagation induces the sudden rise of a radial EF component. Both of these EF components have a few kV/cm in amplitude for helium or neon plasmas. Their amplitude is kept almost constant along a few tens of cm long capillary. The key role of the voltage pulse polarity and the drastic impact of the presence of a target in front of the plasma jet are discussed from Schlieren images. All these experimental measurements are in excellent agreement with model calculations which are used to infer EF data on capillary axis. EF diagnostics in the plasma plume in the free jet mode but also in contact with various targets is proposed. The combination of intense transient EF, both of ns and µs duration, together with significant transient reactive species generation during plasma jet treatments may be reconsidered. Typical EF amplitudes likely to induce electrostimulation, electroporation are indeed probably achieved in many in vivo protocols. Stimulation of tissue oxygenation, blood flow rate modulation and more recently immune system triggering may be examples where EF could play a significant role. The second part of this work is dedicated to the development of multi jets, using two different setups, based on a single plasma source. Plasma splitting in dielectric tubes drilled with sub millimetric orifices, but also plasma transfer across metallic tubes equipped with such orifices are analyzed from ICCD imaging and time resolved EF measurements. This allows for the design of plasma jet arrays but also emphasizes the necessity to account for voltage pulse polarity, target potential status, consecutive helium flow modulation and

  3. Experimental approaches for studying non-equilibrium atmospheric plasma jets

    SciTech Connect

    Shashurin, A.; Keidar, M.

    2015-12-15

    This work reviews recent research efforts undertaken in the area non-equilibrium atmospheric plasma jets with special focus on experimental approaches. Physics of small non-equilibrium atmospheric plasma jets operating in kHz frequency range at powers around few Watts will be analyzed, including mechanism of breakdown, process of ionization front propagation, electrical coupling of the ionization front with the discharge electrodes, distributions of excited and ionized species, discharge current spreading, transient dynamics of various plasma parameters, etc. Experimental diagnostic approaches utilized in the field will be considered, including Rayleigh microwave scattering, Thomson laser scattering, electrostatic streamer scatterers, optical emission spectroscopy, fast photographing, etc.

  4. Plasma reactor for deposition of carbon nanowalls at atmospheric pressure

    NASA Astrophysics Data System (ADS)

    Dimitrov, Zh; Mitev, D.; Kiss'ovski, Zh

    2016-10-01

    In this study a novel plasma reactor for deposition of carbon nanowalls at atmospheric pressure is constructed and characterized. A low power microwave discharge is used as a plasma source and working gas of Ar/H2/CH4 gas mixture. The substrate is heated by plasma flame and its temperature is in the range 600-700 C. The chemical composition of the plasma and the gas mixture effect on the concentration of the various particles in the plasma is investigated by optical emission spectroscopy. The emission spectrum of the plasma jet in Ar/H2/CH4 mixture shows the presence of carbon (Swan band) and an intensive line of CH (388 nm), which are necessary species for deposition of carbon nanostructures. Additional voltage in the range from -20 V to -100 V is applied in order to ensure the vertical growth of graphene walls. Results of deposited carbon nanostructures on metal substrate are shown.

  5. Charged-particle acceleration in braking plasma jets.

    PubMed

    Artemyev, A V

    2014-03-01

    In this paper we describe the mechanism of the charged particle acceleration in space plasma systems. We consider the interaction of nonrelativistic particles with a sub-Alfvenic plasma jet originated from the magnetic reconnection. The sharp front with increased magnetic field amplitude forms in the jet leading edge. Propagation of the jet in the inhomogeneous background plasma results in front braking. We show that particles can interact with this front in a resonance manner. Synchronization of particle reflections from the front and the front braking provides the stable trapping of particles in the vicinity of the front. This trapping supports the effective particle acceleration along the front. The mechanism of acceleration is potentially important due to the prevalence of the magnetic reconnection in space and astrophysical plasmas.

  6. Cold atmospheric plasma jet in an axial DC electric field

    NASA Astrophysics Data System (ADS)

    Lin, Li; Keidar, Michael

    2016-08-01

    Cold atmospheric plasma (CAP) jet is currently intensively investigated as a tool for new and potentially transformative cancer treatment modality. However, there are still many unknowns about the jet behavior that requires attention. In this paper, a helium CAP jet is tested in an electrostatic field generated by a copper ring. Using Rayleigh microwave scattering method, some delays of the electron density peaks for different ring potentials are observed. Meanwhile, a similar phenomenon associated with the bullet velocity is found. Chemical species distribution along the jet is analyzed based on the jet optical emission spectra. The spectra indicate that a lower ring potential, i.e., lower DC background electric field, can increase the amount of excited N2, N2+, He, and O in the region before the ring, but can decrease the amount of excited NO and HO almost along the entire jet. Combining all the results above, we discovered that an extra DC potential mainly affects the temporal plasma jet properties. Also, it is possible to manipulate the chemical compositions of the jet using a ring with certain electric potentials.

  7. Optical and electrical characterization of an atmospheric pressure microplasma jet with a capillary electrode

    SciTech Connect

    Park, Hye Sun; Kim, Sun Ja; Joh, H. M.; Bae, S. H.; Chung, T. H.; Leem, S. H.

    2010-03-15

    A microplasma jet with a capillary electrode working at atmospheric pressure is developed to create nonthermal plasma. This jet can be operated at an excitation frequency either in several tens of kilohertz ac range (or pulsed voltage with a repetition rate of kilohertz range) or in radio-frequency range. The working gas, helium or argon, and the additive gas, oxygen, are fed into the plasma jet. The discharge has been characterized by optical emission spectroscopy. The electrical property of the discharge has been studied by means of voltage and current probes. The dynamic nature of the plume is investigated by using intensified charged coupled device camera. The electron temperature is estimated from the modified Boltzmann plot method utilizing the Ar 4p->4s transitions. The plume temperature is determined by using the fitting the fine structure of the emission bands of OH molecules and by utilizing the line shape of the transition. They are compared with the results obtained by optical fiber thermometer. The characteristics of plasma jet are studied by employing different excitation mode and by adjusting the gas flow rates, the applied voltage, and the amount of additive O{sub 2} flow. The characteristic differences between the Ar plasma jet and the He plasma jet are compared. The effects of the additive O{sub 2} gas are investigated. The plasma bullet velocity is found to increase with the applied voltage but to decrease with the duty cycle. Also the preliminary results of microplasma effects on the human breast cancer cells are presented.

  8. Atmospheric Pressure Low Temperature Plasma System for Additive Manufacturing

    NASA Astrophysics Data System (ADS)

    Burnette, Matthew; Staack, David

    2016-09-01

    There is growing interest in using plasmas for additive manufacturing, however these methods use high temperature plasmas to melt the material. We have developed a novel technique of additive manufacturing using a low temperature dielectric barrier discharge (DBD) jet. The jet is attached to the head of a 3D printer to allow for precise control of the plasma's location. Various methods are employed to deposit the material, including using a vaporized precursor or depositing a liquid precursor directly onto the substrate or into the plasma via a nebulizer. Various materials can be deposited including metals (copper using copper (II) acetylacetonate), polymers (PMMA using the liquid monomer), and various hydrocarbon compounds (using alcohols or a 100% methane DBD jet). The rastering pattern for the 3D printer was modified for plasma deposition, since it was originally designed for thermoplastic extrusion. The design constraints for fill pattern selection for the plasma printer are influenced by substrate heating, deposition area, and precursor consumption. Depositions onto pressure and/or temperature sensitive substrates can be easily achieved. Deposition rates range up to 0.08 cm3/hr using tris(2-methoxyethoxy)(vinyl)silane, however optimization can still be done on the system to improve the deposition rate. For example higher concentration of precursor can be combined with faster motion and higher discharge powers to increase the deposition rate without overheating the substrate.

  9. Non-equilibrium atmospheric pressure microplasma jet: An approach to endoscopic therapies

    NASA Astrophysics Data System (ADS)

    Zuo, Xiao; Wei, Yu; Wei Chen, Long; Dong Meng, Yue; Plasma Medicine Team

    2013-08-01

    Atmospheric pressure microplasma jet generated in a long hollow core optical fiber is studied to verify the potential feasibility of endoscopic therapies. Thermal damage and electric shock to the human body were suppressed by two technical methods, i.e., the high-voltage resistant flexible tube wrapped on the optical fiber and a power resistor of 100 kΩ connected between the power supply and the copper foil electrode. Optical emission spectra analysis indicated that many kinds of active radicals like excited atomic O and OH, were generated in the microplasma jet. In addition, the applications of the microplasma jet on sterilization and lung cancer cell apoptosis were presented. After 5 min of exposures to the microplasma jet, the cell viability and the bacillus subtilis replication decreased to about 3% and zero, respectively. More investigations are needed to improve the plasma-aided endoscopic therapies.

  10. Non-equilibrium atmospheric pressure microplasma jet: An approach to endoscopic therapies

    SciTech Connect

    Zuo, Xiao; Wei, Yu; Wei Chen, Long; Dong Meng, Yue; Collaboration: Plasma Medicine Team

    2013-08-15

    Atmospheric pressure microplasma jet generated in a long hollow core optical fiber is studied to verify the potential feasibility of endoscopic therapies. Thermal damage and electric shock to the human body were suppressed by two technical methods, i.e., the high-voltage resistant flexible tube wrapped on the optical fiber and a power resistor of 100 kΩ connected between the power supply and the copper foil electrode. Optical emission spectra analysis indicated that many kinds of active radicals like excited atomic O and OH, were generated in the microplasma jet. In addition, the applications of the microplasma jet on sterilization and lung cancer cell apoptosis were presented. After 5 min of exposures to the microplasma jet, the cell viability and the bacillus subtilis replication decreased to about 3% and zero, respectively. More investigations are needed to improve the plasma-aided endoscopic therapies.

  11. Experimental investigation of effects of jet decay rate on jet-induced pressures on a flat plate: Tabulated data

    NASA Technical Reports Server (NTRS)

    Kuhlman, J. M.; Ousterhout, D. S.; Warcup, R. W.

    1978-01-01

    Tabular data are presented for an experimental study of the effects of jet decay rate on the jet-induced pressure distribution on a flat plate for a single jet issuing at right angle to the flat plate into a uniform crossflow. The data are presented in four sections: (1) presents the static nozzle calibration data; (2) lists the plate surface static pressure data and integrated loads; (3) lists the jet centerline trajectory data; and (4) lists the centerline dynamic pressure data.

  12. Initial condition effect on pressure waves in an axisymmetric jet

    NASA Technical Reports Server (NTRS)

    Miles, Jeffrey H.; Raman, Ganesh

    1988-01-01

    A pair of microphones (separated axially by 5.08 cm and laterally by 1.3 cm) are placed on either side of the jet centerline to investigate coherent pressure fluctuations in an axisymmetric jet at Strouhal numbers less than unity. Auto-spectra, transfer-function, and coherence measurements are made for a tripped and untripped boundary layer initial condition. It was found that coherent acoustic pressure waves originating in the upstream plenum chamber propagate a greater distance downstream for the tripped initial condition than for the untripped initial condition. In addition, for the untripped initial condition the development of the coherent hydrodynamic pressure waves shifts downstream.

  13. Dust generation at interaction of plasma jet with surfaces

    NASA Astrophysics Data System (ADS)

    Ticos, Catalin; Toader, Dorina; Banu, Nicoleta; Scurtu, Adrian; Oane, Mihai

    2013-10-01

    Coatings of W and C with widths of a few microns will be exposed to plasma jet for studying the erosion of the surface and detachment of micron size dust particles. A coaxial plasma gun has been built inside a vacuum chamber for producing supersonic plasma jets. Its design is based on a 50 kJ coaxial plasma gun which has been successfully used for accelerating hypervelocity dust. Initial shots were carried out for a capacitor bank with C = 12 μF and charged up to 2 kV. Currents of tens of amps were measured with a Rogowsky coil and plasma flow speeds of 4 km/s were inferred from high-speed images of jet propagation. An upgrade consisting in adding capacitors in parallel will be performed in order to increase the energy up to 2 kJ. A coil will be installed at the gun muzzle to compress the plasma flow and increase the energy density of the jet on the sample surface. A CCD camera with a maximum recording speed of 100 k fps and a maximum resolution of 1024 × 1024 pixels was set for image acquisition of the plasma and dust. A laser system used to illuminate the ejected dust from the surface includes a laser diode emitting at 650 nm with a beam power of 25 mW. The authors acknowledge support from EURATOM WP13-IPH-A03-P2-02-BS22.

  14. Experimental characterization of railgun-driven supersonic plasma jets motivated by high energy density physics applications

    SciTech Connect

    Hsu, S. C.; Moser, A. L.; Awe, T. J.; Davis, J. S.; Dunn, J. P.; Merritt, E. C.; Adams, C. S.; Brockington, S. J. E.; Case, A.; Messer, S. J.; Witherspoon, F. D.; Cassibry, J. T.; Gilmore, M. A.; Lynn, A. G.

    2012-12-15

    We report experimental results on the parameters, structure, and evolution of high-Mach-number (M) argon plasma jets formed and launched by a pulsed-power-driven railgun. The nominal initial average jet parameters in the data set analyzed are density Almost-Equal-To 2 Multiplication-Sign 10{sup 16} cm{sup -3}, electron temperature Almost-Equal-To 1.4 eV, velocity Almost-Equal-To 30 km/s, M Almost-Equal-To 14, ionization fraction Almost-Equal-To 0.96, diameter Almost-Equal-To 5 cm, and length Almost-Equal-To 20 cm. These values approach the range needed by the Plasma Liner Experiment, which is designed to use merging plasma jets to form imploding spherical plasma liners that can reach peak pressures of 0.1-1 Mbar at stagnation. As these jets propagate a distance of approximately 40 cm, the average density drops by one order of magnitude, which is at the very low end of the 8-160 times drop predicted by ideal hydrodynamic theory of a constant-M jet.

  15. Plasma performance in JET: Achievements and projections

    SciTech Connect

    Gibson, A.

    1988-01-01

    An account is given of recent experimental advances on JET, especially as they relate to fusion performance. Scaling relations are used to identify the critical parameters which need to be optimized to secure the best fusion performance. Finally the established best performance of JET is used as a base to project the performance to be expected in future D-T operation. 13 refs., 20 figs., 6 tabs.

  16. Titanium alloys milling assistance by high pressure lubricoolant jet

    SciTech Connect

    Mazurkiewicz, M.

    1992-11-12

    The study of high pressure lubricooling jet injection into tool/chip interface showed good results by decreasing friction, tool forces, and temperature at tool/chip interface. Tool wear vs time using different cooling conditions at 1.52 mm depth of cut is shown. Surface roughness generated is in lower range for water jet assisted tool. A test chart is given for visualization of chip formation.

  17. Schlieren Cinematography of Current Driven Plasma Jet Dynamics

    NASA Astrophysics Data System (ADS)

    Loebner, Keith; Underwood, Thomas; Cappelli, Mark

    2016-10-01

    Schlieren cinematography of a pulsed plasma deflagration jet is presented and analyzed. An ultra-high frame rate CMOS camera coupled to a Z-type laser Schlieren apparatus is used to obtain flow-field refractometry data for the continuous flow Z-pinch formed within the plasma deflagration jet. The 10 MHz frame rate for 256 consecutive frames provides high temporal resolution, enabling turbulent fluctuations and plasma instabilities to be visualized over the course of a single pulse (20 μs). The Schlieren signal is radiometrically calibrated to obtain a two dimensional mapping of the refraction angle of the axisymmetric pinch plasma, and this mapping is then Abel inverted to derive the plasma density distribution as a function radius, axial coordinate, and time. Analyses of previously unknown discharge characteristics and comparisons with prior work are discussed.

  18. Characterization of a small railgun-based plasma jet source

    NASA Astrophysics Data System (ADS)

    Schneider, Maximilian; Adams, Colin; Popescu, Marius; Korsness, Joshua; Sherburne, Michael

    2016-10-01

    Experimental characterization of a small plasma jet source has been undertaken at Virginia Tech's Center for Space Science and Engineering Research (Space@VT). The plasma-armature railgun features a square bore approximately 0.5 × 0.5 cm and a rail length of 10 cm. Fed by an 100 psi- gas manifold and powered by an LC pulse-forming network capable of delivering 100 kA current on timescales of several microseconds, jet velocities in the 10-20 km/s range are predicted. A modular design, the insulators and rails are readily swappable for investigation the interaction of the plasma armature with plasma-facing components fabricated with different materials and geometry. The plasma jet is characterized by a suite of diagnostics including a multichord Mach-Zehnder interferometer, spectrometer, photodiode array, and fast photography. Diagnostics planned for the near future include plasma laser-induced fluorescence and particle energy analyzers. The railgun source described is envisioned as a future platform for basic science experiments on topics ranging from plasma-material interaction to plasma shocks.

  19. Advances in physical study of high enthalpy plasma jets of technological interest: emission spectra and plasma characteristics

    NASA Astrophysics Data System (ADS)

    Belevtsev, A. A.; Chinnov, V. F.; Isakaev, E. Kh.; Markin, A. V.; Tazikova, T. F.; Tereshkin, S. A.

    1998-10-01

    Offers a comprehensive study of the emission spectra and plasma characteristics of high enthalpy atmospheric pressure argon and nitrogen jets produced by a high- current industrially important arc plasmatron with a vortex stabilized channel-anode (I<=3D500A, G=3D1-4g/s, jet diameter at a minimum-6mm). The spectra are taken at different distances from the cathode in the 200-950nm region with a spectral resolution=3D0.01nm allowing a fine structure of vibronic bands to be essentially resolved except that due to the dublet (spin) splitting and Λ-doubling. Also derived (through the Abel inversion) are radial distributions of plasma components. The spectra obtained have been used for determining plasma composition, the electron component parameters (by atomic/ionic Stark half-widths and intensities) and the assessment of rotational and vibrational temperatures by simulating molecular bands.

  20. Driving Flows in Laboratory Astrophysical Plasma Jets: The Mochi.LabJet Experiment

    NASA Astrophysics Data System (ADS)

    Carroll, Evan G.

    Mochi.Labjet is a new experiment at the University of Washington developed to investigate the interaction of shear flows in plasma jets with boundary conditions similar to an accretion disc system. This thesis details the engineering design and first plasmas of the Mochi.Labjet experiment. The experiment required construction of a new three electrode plasma gun with azimuthal symmetric gas injection, two optically-isolated pulsed power supplies for generating and sustaining plasma, and one optically-isolated pulsed power supply for generating a background magnetic field. Optical isolation is achieved with four custom circuits: the TTL-optical transmitter, optical-TTL receiver, optical-relay, and optical-tachometer circuits. First plasmas, during the commissioning phase of the apparatus, show evidence of flared jet structures with significant azimuthal symmetry.

  1. Influence of geometrical parameters on performance of plasma synthetic jet actuator

    NASA Astrophysics Data System (ADS)

    Zong, Hao-hua; Wu, Yun; Jia, Min; Song, Hui-min; Liang, Hua; Li, Ying-hong; Zhang, Zhi-bo

    2016-01-01

    Plasma synthetic jet actuator (PSJA) has shown wide and promising application prospects in a high speed flow control field, due to its rapid response, high exhaust velocity, and non-moving components. In this paper, the total pressure profile of a plasma synthetic jet (PSJ) is measured and a new method is developed to evaluate the pulsed thrust of the PSJA. The influence of geometrical parameters including the electrode distance, the orifice diameter, and the throat length on PSJA performance is analyzed based on the pulsed thrust, the discharge characteristics, and the schlieren images. When varying the electrode distance, the dominant factor determining the jet intensity is the heating volume instead of the discharge energy. For the arc discharge, the electrode distance should be extended to increase both the jet velocity and the jet duration time. The design of the orifice diameter should be based on the controlled flow field. A large orifice diameter produces a strong perturbation with short time duration, while a small orifice diameter induces a lasting jet with low mass flux. In order to obtain better high frequency performance, the throat length should be shortened on the condition that the structural strength of the PSJA is maintained, while there is almost no influence of the throat length on the single cycle performance of the PSJA. Once the discharge energy is fixed, the pulsed thrust remains almost unchanged with different orifice diameters and throat lengths. These three geometrical parameters are independent to some extent and can be optimized separately.

  2. On the recovery of pedestal temperature of JET-ILW plasmas with injection of low-Z impurities

    NASA Astrophysics Data System (ADS)

    Giroud, Carine

    2016-10-01

    The pedestal confinement has significantly decreased in JET with its metallic ITER-like wall with reference to the carbon wall phase of JET (JET-C). A reduction in pedestal temperature is observed in all scenarios regardless of the level of D-gas injection or value of βN. In particular, the JET-ILW 2.5MA/2.7T high- δ (δ = 0.4) plasmas at nped/nGW >= 0.7, discharges most comparable with JET-C, the pedestal pressure has reduced by 40% with a decrease in pedestal temperature from 0.9keV to 0.5keV with the change of wall. The pedestal stability has been modified with the new wall: the reference JET-C plasmas pedestals had an operational point in the corner of the Peeling-Ballooning (PB) diagram, with pressure limited by intermediate n-numbers (n =5-20), whereas the JET-ILW unseeded plasmas have a lower pressure gradient limited by high n-numbers >=70 (ballooning modes). Seeding N, a low-Z impurity, almost recovers the thermal stored energy, pedestal pressure and pedestal temperature to JET-C levels and with an operation point in the corner of the PB diagram. The mechanisms linked to the pedestal recovery with N are likely related to the mechanisms leading to a decrease in pedestal temperature in the absence of C in the plasma composition. The improved pedestal stability with N is not solely linked to the ideal linear PB stability since N-seeded plasmas in JET-ILW can be in type-III ELM regime and have a higher pedestal pressure than unseeded type-I ELMy H-mode. An increased pedestal pressure via an inward movement of the pedestal pressure from the separatrix is not observed with N seeding. However, we have identified two mechanisms responsible. A first initial mechanism linked to the change in ELM energy losses which raises modestly the average global beta by 10% but allows in return a second mechanism to take place. The considered high- δ plasmas can then benefit, if in type-I ELM regime, from the virtuous cycle (2nd mechanisms) of an increased Shafranov shift

  3. Radio jet refraction in galactic atmospheres with static pressure gradients

    NASA Technical Reports Server (NTRS)

    Henriksen, R. N.; Vallee, J. P.; Bridle, A. H.

    1981-01-01

    A theory based on the refraction of radio jets in the extended atmosphere of an elliptical galaxy, is proposed for double radio sources with a Z or S morphology. The model describes a collimated jet of supersonic material that bends self-consistently under the influence of external static pressure gradients, and may alternatively be seen as a continuous-jet version of the buoyancy model proposed by Gull (1973). Emphasis is placed on (1) S-shaped radio sources identified with isolated galaxies, such as 3C 293, whose radio structures should be free of distortions resulting from motion relative to a cluster medium, and (2) small-scale, galaxy-dominated rather than environment-dominated S-shaped sources such as the inner jet structure of Fornax A.

  4. Capillary plasma jet: A low volume plasma source for life science applications

    NASA Astrophysics Data System (ADS)

    Topala, I.; Nagatsu, M.

    2015-02-01

    In this letter, we present results from multispectroscopic analysis of protein films, after exposure to a peculiar plasma source, i.e., the capillary plasma jet. This plasma source is able to generate very small pulsed plasma volumes, in kilohertz range, with characteristic dimensions smaller than 1 mm. This leads to specific microscale generation and transport of all plasma species. Plasma diagnosis was realized using general electrical and optical methods. Depending on power level and exposure duration, this miniature plasma jet can induce controllable modifications to soft matter targets. Detailed discussions on protein film oxidation and chemical etching are supported by results from absorption, X-ray photoelectron spectroscopy, and microscopy techniques. Further exploitation of principles presented here may consolidate research interests involving plasmas in biotechnologies and plasma medicine, especially in patterning technologies, modified biomolecule arrays, and local chemical functionalization.

  5. Capillary plasma jet: A low volume plasma source for life science applications

    SciTech Connect

    Topala, I. E-mail: tmnagat@ipc.shizuoka.ac.jp; Nagatsu, M. E-mail: tmnagat@ipc.shizuoka.ac.jp

    2015-02-02

    In this letter, we present results from multispectroscopic analysis of protein films, after exposure to a peculiar plasma source, i.e., the capillary plasma jet. This plasma source is able to generate very small pulsed plasma volumes, in kilohertz range, with characteristic dimensions smaller than 1 mm. This leads to specific microscale generation and transport of all plasma species. Plasma diagnosis was realized using general electrical and optical methods. Depending on power level and exposure duration, this miniature plasma jet can induce controllable modifications to soft matter targets. Detailed discussions on protein film oxidation and chemical etching are supported by results from absorption, X-ray photoelectron spectroscopy, and microscopy techniques. Further exploitation of principles presented here may consolidate research interests involving plasmas in biotechnologies and plasma medicine, especially in patterning technologies, modified biomolecule arrays, and local chemical functionalization.

  6. High fusion performance from deuterium-tritium plasmas in JET

    NASA Astrophysics Data System (ADS)

    Keilhacker, M.; Gibson, A.; Gormezano, C.; Lomas, P. J.; Thomas, P. R.; Watkins, M. L.; Andrew, P.; Balet, B.; Borba, D.; Challis, C. D.; Coffey, I.; Cottrell, G. A.; DeEsch, H. P. L.; Deliyanakis, N.; Fasoli, A.; Gowers, C. W.; Guo, H. Y.; Huysmans, G. T. A.; Jones, T. T. C.; Kerner, W.; König, R. W. T.; Loughlin, M. J.; Maas, A.; Marcus, F. B.; Nave, M. F. F.; Rimini, F. G.; Sadler, G. J.; Sharapov, S. E.; Sips, G.; Smeulders, P.; Söldner, F. X.; Taroni, A.; Tubbing, B. J. D.; von Hellermann, M. G.; Ward, D. J.; JET Team

    1999-02-01

    High fusion power experiments using DT mixtures in ELM-free H mode and optimized shear regimes in JET are reported. A fusion power of 16.1 MW has been produced in an ELM-free H mode at 4.2 MA/3.6 T. The transient value of the fusion amplification factor was 0.95+/-0.17, consistent with the high value of nDT(0)τEdiaTi(0) = 8.7 × 1020+/-20% m-3 s keV, and was maintained for about half an energy confinement time until excessive edge pressure gradients resulted in discharge termination by MHD instabilities. The ratio of DD to DT fusion powers (from separate but otherwise similar discharges) showed the expected factor of 210, validating DD projections of DT performance for similar pressure profiles and good plasma mixture control, which was achieved by loading the vessel walls with the appropriate DT mix. Magnetic fluctuation spectra showed no evidence of Alfvénic instabilities driven by alpha particles, in agreement with theoretical model calculations. Alpha particle heating has been unambiguously observed, its effect being separated successfully from possible isotope effects on energy confinement by varying the tritium concentration in otherwise similar discharges. The scan showed that there was no, or at most a very weak, isotope effect on the energy confinement time. The highest electron temperature was clearly correlated with the maximum alpha particle heating power and the optimum DT mixture; the maximum increase was 1.3+/-0.23 keV with 1.3 MW of alpha particle heating power, consistent with classical expectations for alpha particle confinement and heating. In the optimized shear regime, clear internal transport barriers were established for the first time in DT, with a power similar to that required in DD. The ion thermal conductivity in the plasma core approached neoclassical levels. Real time power control maintained the plasma core close to limits set by pressure gradient driven MHD instabilities, allowing 8.2 MW of DT fusion power with nDT(0)τEdiaTi(0

  7. Atmospheric-Pressure Plasma Cleaning of Contaminated Surfaces

    SciTech Connect

    Robert F. Hicks; Gary S. Selwyn

    2001-01-09

    Project was to develop a low-cost, environmentally benign technology for the decontamination and decommissioning of transuranic waste. With the invention of the atmospheric-pressure plasma jet the goal was achieved. This device selectively etches heavy metals from surfaces, rendering objects radiation free and suitable for decommissioning. The volatile reaction products are captured on filters, which yields a tremendous reduction in the volume of the waste. Studies on tantalum, a surrogate material for plutonium, have shown that etch rate of 6.0 microns per minute can be achieved under mild conditions. Over the past three years, we have made numerous improvements in the design of the plasma jet. It may now be operated for hundreds of hours and not undergo any degradation in performance. Furthermore, small compact units have been developed, which are easily deployed in the field.

  8. Numerical simulations of the bending of narrow-angle-tail radio jets by ram pressure or pressure gradients

    NASA Technical Reports Server (NTRS)

    Soker, Noam; Sarazin, Craig L.; O'Dea, Christopher P.

    1988-01-01

    Three-dimensional numerical hydrodynamic simulations are used to study the bending of radio jets. The simulations are compared with observations of jets in narrow-angle-tail radio sources. Two mechanisms for the observed bending are considered: direct bending of quasi-continuous jets by ram pressure from intergalactic gas and bending by pressure gradients in the interstellar gas of the host galaxy, the pressure gradients themselves being the result of ram pressure by intergalactic gas. It is shown that the pressure gradients are much less effective in bending jets, implying that the jets have roughly 30 times lower momentum fluxes if they are bent by this mechanism. Ram-pressure bending produces jets with 'kidney-shaped' cross sections; when observed from the side, these jets appear to have diffuse extensions on the downstream side. On the other hand, pressure-gradient bending causes the jets to be densest near their upstream side.

  9. Comparison of Theory with Rotation Measurements in JET ICRH Plasmas

    SciTech Connect

    R.V. Budny; C.S. Chang; C. Giroud; R.J. Goldston; D. McCune; J. Ongena; F.W. Perkins; R.B. White; K.-D. Zastrow; and contributors to the EFDA-JET work programme

    2001-06-27

    Plasma rotation appears to improve plasma performance by increasing the E x B flow shearing rate, thus decreasing radial correlations in the microturbulence. Also, plasma rotation can increase the stability to resistive MHD modes. In the Joint European Torus (JET), toroidal rotation rates omega (subscript ''tor'') with high Mach numbers are generally measured in NBI-heated plasmas (since the neutral beams aim in the co-plasma current direction). They are considerably lower with only ICRH (and Ohmic) heating, but still surprisingly large considering that ICRH appears to inject relatively small amounts of angular momentum. Either the applied torques are larger than naively expected, or the anomalous transport of angular momentum is smaller than expected. Since ICRH is one of the main candidates for heating next-step tokamaks, and for creating burning plasmas in future tokamak reactors, this paper attempts to understand ICRH-induced plasma rotation.

  10. Classifier based on support vector machine for JET plasma configurations

    SciTech Connect

    Dormido-Canto, S.; Farias, G.; Dormido, R.; Sanchez, J.; Duro, N.; Vargas, H.

    2008-10-15

    The last flux surface can be used to identify the plasma configuration of discharges. For automated recognition of JET configurations, a learning system based on support vector machines has been developed. Each configuration is described by 12 geometrical parameters. A multiclass system has been developed by means of the one-versus-the-rest approach. Results with eight simultaneous classes (plasma configurations) show a success rate close to 100%.

  11. On Power Measurements of Single-Electrode Low-Power Ar Plasma Jets

    NASA Astrophysics Data System (ADS)

    Prysiazhnyi, Vadym; Ricci, Alonso H. C.; Kostov, Konstantin G.

    2016-10-01

    A study of electrical properties, methodology, and precision of power measurement was made on two types of Ar plasma jets, a single-strip-electrode plasma jet and a single-rod-electrode plasma jet. The dynamics of current peaks, methods for determining discharge power, and power measurement precision (especially important for applications in plasma medicine) are discussed for each type of plasma jet. Lower error in power calculation was obtained when the plasma jet did not touch the substrate, as well as more repetitive dynamics of the current peaks. Averaging high number of periods (over 500) when calculating the power by the Lissajous figure technique led to decrease of the experimental error.

  12. Major vascular injury from high-pressure water jet.

    PubMed

    Harvey, R L; Ashley, D A; Yates, L; Dalton, M L; Solis, M M

    1996-01-01

    High-pressure water jets are used in industry as a cleaning and cutting tool. Penetrating injuries by these devices can produce minimal external evidence of extensive internal damage. We report a literature review and the case of a limb-threatening injury to the lower extremity caused by such a device.

  13. Experimental tests for carbon nanomaterial synthesis using DC plasma jet

    NASA Astrophysics Data System (ADS)

    Lange, H.; Łabȩdź, O.; Tylska, I.; Huczko, A.; Bystrzejewski, M.

    2014-11-01

    In the frame of this work some experimental tests were performed in the plasma jet. Pure ethanol vapour alone or with the addition of fine iron powder were used to synthesize few-layer graphene or carbon-encapsulated iron nanoparticles, respectively.

  14. Degradation of tungsten under the action of a plasma jet

    NASA Astrophysics Data System (ADS)

    Voronin, A. V.; Sud'enkov, Yu. V.; Semenov, B. N.; Atroshenko, S. A.; Naumova, N. S.

    2014-07-01

    The degradation of the surface and structure of single-crystal tungsten and sintered powder tungsten during the action of a pulsed plasma jet is studied. It is shown that the degradation of a tungsten target during the action of a plasma jet with an energy flux density of 0.25-1 MJ/m2 is accompanied by surface evaporation and melting and the fracture of surface layers on scales of 150-250 μm. The results of a numerical simulation of the thermomechanical processes that occur in a tungsten target during the action of a plasma jet are presented. The degradation of tungsten during the action of a plasma jet is shown to proceed almost continuously from the action (evaporation, melting) to the times that are more than three orders of magnitude longer than the action time, which is caused by the thermomechanical processes occurring in the tungsten target. Moreover, the action of thermal stresses leads to structural and morphological changes throughout the sample volume, and these changes are accompanied by recrystallization in adiabatic shear bands.

  15. Microhole High-Pressure Jet Drill for Coiled Tubing

    SciTech Connect

    Ken Theimer; Jack Kolle

    2007-06-30

    Tempress Small Mechanically-Assisted High-Pressure Waterjet Drilling Tool project centered on the development of a downhole intensifier (DHI) to boost the hydraulic pressure available from conventional coiled tubing to the level required for high-pressure jet erosion of rock. We reviewed two techniques for implementing this technology (1) pure high-pressure jet drilling and (2) mechanically-assisted jet drilling. Due to the difficulties associated with modifying a downhole motor for mechanically-assisted jet drilling, it was determined that the pure high-pressure jet drilling tool was the best candidate for development and commercialization. It was also determined that this tool needs to run on commingled nitrogen and water to provide adequate downhole differential pressure and to facilitate controlled pressure drilling and descaling applications in low pressure wells. The resulting Microhole jet drilling bottomhole assembly (BHA) drills a 3.625-inch diameter hole with 2-inch coil tubing. The BHA consists of a self-rotating multi-nozzle drilling head, a high-pressure rotary seal/bearing section, an intensifier and a gas separator. Commingled nitrogen and water are separated into two streams in the gas separator. The water stream is pressurized to 3 times the inlet pressure by the downhole intensifier and discharged through nozzles in the drilling head. The energy in the gas-rich stream is used to power the intensifier. Gas-rich exhaust from the intensifier is conducted to the nozzle head where it is used to shroud the jets, increasing their effective range. The prototype BHA was tested at operational pressures and flows in a test chamber and on the end of conventional coiled tubing in a test well. During instrumented runs at downhole conditions, the BHA developed downhole differential pressures of 74 MPa (11,000 psi, median) and 90 MPa (13,000 psi, peaks). The median output differential pressure was nearly 3 times the input differential pressure available from the

  16. Measurements of railgun generated supersonic plasma jet propagation and two jet oblique merging

    NASA Astrophysics Data System (ADS)

    Merritt, Elizabeth C.

    Imploding spherical plasma liners have been proposed as a possible method for creating high-energy-density (HED) laboratory plasmas and as a standoff driver for magneto-inertial fusion (MIF). The Plasma Liner Experiment (PLX) planned a three-phase experimental program to study the feasibility of using railgun-driven supersonic jets to form imploding spherical plasma liners. The three phases are to investigate single-jet evolution during propagation, to merge 2-5 jets to assess the suitability of merging for liner formation, and to merge 30 jets in spherical symmetry to form a complete liner. We present here details of single-jet propagation and two-jet oblique merging experiments completed on PLX. A key component of this dissertation was the design, implementation, and operation of a novel 8 chord, fiber-coupled interferometer based on a long coherence length (> 100 m) 561 nm diode-pumped solid state laser. This interferometer was a critical diagnostic in both single-jet propagation and two-jet merging studies. The long laser coherence length and fiber-optic design allowed signal and reference path lengths in the interferometer to be mismatched by many meters without signal degradation, greatly simplified interferometer optical layout, and added flexibility in interferometer positioning for both propagation and merging experiments. The interferometer sensitivity to ions, neutral atoms, and electrons required development of a phase shift analysis that incorporated the presence of neutrals, impurities, and multiply ionized species. Interferometry, coupled with spectroscopic ionization fraction estimates, was used to assess time resolved density profile measurements. Survey spectroscopy inferred both Te and ionization fraction f via non-local-thermodynamic-equilibrium (non-LTE) atomic/equation-of-state (EOS) modeling. A fast CCD camera and photo-diode array allowed for assessment of plasma emission for velocity and jet profile measurements. Initial jet parameters were

  17. Laser plasma at low air pressure

    NASA Astrophysics Data System (ADS)

    Vas'kovskii, Iu. M.; Moiseev, V. N.; Rovinskii, R. E.; Tsenina, I. S.

    1993-01-01

    The ambient-pressure dependences of the dynamic and optical characteristics of a laser plasma generated by CO2-laser irradiation of an obstacle are investigated experimentally. The change of the sample's surface roughness after irradiation is investigated as a function of air pressure. It is concluded that the transition from the air plasma to the erosion plasma takes place at an air pressure of about 1 mm Hg. The results confirm the existing theory of plasma formation near the surface of an obstacle under the CO2-laser pulse effect in air.

  18. Characterization of Wet Air Plasma Jet Powered by Sinusoidal High Voltage and Nanosecond Pulses for Plasma Agricultural Application

    NASA Astrophysics Data System (ADS)

    Takashima, Keisuke; Shimada, Keisuke; Konishi, Hideaki; Kaneko, Toshiro

    2015-09-01

    Not only for the plasma sterilization but also for many of plasma life-science applications, atmospheric pressure plasma devices that allowed us to control its state and reactive species production are deserved to resolve the roles of the chemical species. Influence of the hydroxyl radical and ozone on germination of conidia of a strawberry pathogen is presented. Water addition to air plasma jet significantly improves germination suppression performance, while measured reactive oxygen species (ROS) are reduced. Although the results show a negative correlation between ROS and the germination suppression, this infers the importance of chemical composition generated by plasma. For further control of the plasma product, a plasma jet powered by sinusoidal high voltage and nanosecond pulses is developed and characterized with the voltage-charge Lissajous. Control of breakdown phase and discharge power by pulse-imposed phase is presented. This work is supported by JSPS KAKENHI Grant-in-Aid for Young Scientists (B) Grant Number 15K17480 and Exploratory Research Grant Number 23644199.

  19. Laboratory Plasma Source as an MHD Model for Astrophysical Jets

    NASA Technical Reports Server (NTRS)

    Mayo, Robert M.

    1997-01-01

    The significance of the work described herein lies in the demonstration of Magnetized Coaxial Plasma Gun (MCG) devices like CPS-1 to produce energetic laboratory magneto-flows with embedded magnetic fields that can be used as a simulation tool to study flow interaction dynamic of jet flows, to demonstrate the magnetic acceleration and collimation of flows with primarily toroidal fields, and study cross field transport in turbulent accreting flows. Since plasma produced in MCG devices have magnetic topology and MHD flow regime similarity to stellar and extragalactic jets, we expect that careful investigation of these flows in the laboratory will reveal fundamental physical mechanisms influencing astrophysical flows. Discussion in the next section (sec.2) focuses on recent results describing collimation, leading flow surface interaction layers, and turbulent accretion. The primary objectives for a new three year effort would involve the development and deployment of novel electrostatic, magnetic, and visible plasma diagnostic techniques to measure plasma and flow parameters of the CPS-1 device in the flow chamber downstream of the plasma source to study, (1) mass ejection, morphology, and collimation and stability of energetic outflows, (2) the effects of external magnetization on collimation and stability, (3) the interaction of such flows with background neutral gas, the generation of visible emission in such interaction, and effect of neutral clouds on jet flow dynamics, and (4) the cross magnetic field transport of turbulent accreting flows. The applicability of existing laboratory plasma facilities to the study of stellar and extragalactic plasma should be exploited to elucidate underlying physical mechanisms that cannot be ascertained though astrophysical observation, and provide baseline to a wide variety of proposed models, MHD and otherwise. The work proposed herin represents a continued effort on a novel approach in relating laboratory experiments to

  20. High pressure water jet cutting and stripping

    NASA Technical Reports Server (NTRS)

    Hoppe, David T.; Babai, Majid K.

    1991-01-01

    High pressure water cutting techniques have a wide range of applications to the American space effort. Hydroblasting techniques are commonly used during the refurbishment of the reusable solid rocket motors. The process can be controlled to strip a thermal protective ablator without incurring any damage to the painted surface underneath by using a variation of possible parameters. Hydroblasting is a technique which is easily automated. Automation removes personnel from the hostile environment of the high pressure water. Computer controlled robots can perform the same task in a fraction of the time that would be required by manual operation.

  1. Atmospheric Pressure Plasma Process And Applications

    SciTech Connect

    Peter C. Kong; Myrtle

    2006-09-01

    This paper provides a general discussion of atmospheric-pressure plasma generation, processes, and applications. There are two distinct categories of atmospheric-pressure plasmas: thermal and nonthermal. Thermal atmospheric-pressure plasmas include those produced in high intensity arcs, plasma torches, or in high intensity, high frequency discharges. Although nonthermal plasmas are at room temperatures, they are extremely effective in producing activated species, e.g., free radicals and excited state atoms. Thus, both thermal and nonthermal atmosphericpressure plasmas are finding applications in a wide variety of industrial processes, e.g. waste destruction, material recovery, extractive metallurgy, powder synthesis, and energy conversion. A brief discussion of recent plasma technology research and development activities at the Idaho National Laboratory is included.

  2. Plasma jet acceleration of dust particles to hypervelocities

    SciTech Connect

    Ticos, C. M.; Wang, Zhehui; Wurden, G. A.; Kline, J. L.; Montgomery, D. S.

    2008-10-15

    A convenient method to accelerate simultaneously hundreds of micron-size dust particles to a few km/s over a distance of about 1 m is based on plasma drag. Plasma jets which can deliver sufficient momentum to the dust particles need to have speeds of at least several tens of km/s, densities of the order of 10{sup 22} m{sup -3} or higher, and low temperature {approx}1 eV, in order to prevent dust destruction. An experimental demonstration of dust particles acceleration to hypervelocities by plasma produced in a coaxial gun is presented here. The plasma flow speed is deduced from photodiode signals while the plasma density is measured by streaked spectroscopy. As a result of the interaction with the plasma jet, the dust grains are also heated to high temperatures and emit visible light. A hypervelocity dust shower is imaged in situ with a high speed video camera at some distance from the coaxial gun, where light emission from the plasma flow is less intense. The bright traces of the flying microparticles are used to infer their speed and acceleration by employing the time-of-flight technique. A simple model for plasma drag which accounts for ion collection on the grain surface gives predictions for dust accelerations which are in good agreement with the experimental observations.

  3. Impact of plasma jet vacuum ultraviolet radiation on reactive oxygen species generation in bio-relevant liquids

    SciTech Connect

    Jablonowski, H.; Hammer, M. U.; Reuter, S.; Bussiahn, R.; Weltmann, K.-D.; Woedtke, Th. von

    2015-12-15

    Plasma medicine utilizes the combined interaction of plasma produced reactive components. These are reactive atoms, molecules, ions, metastable species, and radiation. Here, ultraviolet (UV, 100–400 nm) and, in particular, vacuum ultraviolet (VUV, 10–200 nm) radiation generated by an atmospheric pressure argon plasma jet were investigated regarding plasma emission, absorption in a humidified atmosphere and in solutions relevant for plasma medicine. The energy absorption was obtained for simple solutions like distilled water (dH{sub 2}O) or ultrapure water and sodium chloride (NaCl) solution as well as for more complex ones, for example, Rosewell Park Memorial Institute (RPMI 1640) cell culture media. As moderate stable reactive oxygen species, hydrogen peroxide (H{sub 2}O{sub 2}) was studied. Highly reactive oxygen radicals, namely, superoxide anion (O{sub 2}{sup •−}) and hydroxyl radicals ({sup •}OH), were investigated by the use of electron paramagnetic resonance spectroscopy. All species amounts were detected for three different treatment cases: Plasma jet generated VUV and UV radiation, plasma jet generated UV radiation without VUV part, and complete plasma jet including all reactive components additionally to VUV and UV radiation. It was found that a considerable amount of radicals are generated by the plasma generated photoemission. From the experiments, estimation on the low hazard potential of plasma generated VUV radiation is discussed.

  4. Impact of plasma jet vacuum ultraviolet radiation on reactive oxygen species generation in bio-relevant liquids

    NASA Astrophysics Data System (ADS)

    Jablonowski, H.; Bussiahn, R.; Hammer, M. U.; Weltmann, K.-D.; von Woedtke, Th.; Reuter, S.

    2015-12-01

    Plasma medicine utilizes the combined interaction of plasma produced reactive components. These are reactive atoms, molecules, ions, metastable species, and radiation. Here, ultraviolet (UV, 100-400 nm) and, in particular, vacuum ultraviolet (VUV, 10-200 nm) radiation generated by an atmospheric pressure argon plasma jet were investigated regarding plasma emission, absorption in a humidified atmosphere and in solutions relevant for plasma medicine. The energy absorption was obtained for simple solutions like distilled water (dH2O) or ultrapure water and sodium chloride (NaCl) solution as well as for more complex ones, for example, Rosewell Park Memorial Institute (RPMI 1640) cell culture media. As moderate stable reactive oxygen species, hydrogen peroxide (H2O2) was studied. Highly reactive oxygen radicals, namely, superoxide anion (O2•-) and hydroxyl radicals (•OH), were investigated by the use of electron paramagnetic resonance spectroscopy. All species amounts were detected for three different treatment cases: Plasma jet generated VUV and UV radiation, plasma jet generated UV radiation without VUV part, and complete plasma jet including all reactive components additionally to VUV and UV radiation. It was found that a considerable amount of radicals are generated by the plasma generated photoemission. From the experiments, estimation on the low hazard potential of plasma generated VUV radiation is discussed.

  5. Dust particles interaction with plasma jet

    SciTech Connect

    Ticos, C. M.; Jepu, I.; Lungu, C. P.; Chiru, P.; Zaroschi, V.

    2009-11-10

    The flow of plasma and particularly the flow of ions play an important role in dusty plasmas. Here we present some instances in laboratory experiments where the ion flow is essential in establishing dust dynamics in strongly or weakly coupled dust particles. The formation of ion wake potential and its effect on the dynamics of dust crystals, or the ion drag force exerted on micron size dust grains are some of the phenomena observed in the presented experiments.

  6. Plasma phenomenology in astrophysical systems: Radio-sources and jets

    SciTech Connect

    Montani, Giovanni; Petitta, Jacopo

    2014-06-15

    We review the plasma phenomenology in the astrophysical sources which show appreciable radio emissions, namely Radio-Jets from Pulsars, Microquasars, Quasars, and Radio-Active Galaxies. A description of their basic features is presented, then we discuss in some details the links between their morphology and the mechanisms that lead to the different radio-emissions, investigating especially the role played by the plasma configurations surrounding compact objects (Neutron Stars, Black Holes). For the sake of completeness, we briefly mention observational techniques and detectors, whose structure set them apart from other astrophysical instruments. The fundamental ideas concerning angular momentum transport across plasma accretion disks—together with the disk-source-jet coupling problem—are discussed, by stressing their successes and their shortcomings. An alternative scenario is then inferred, based on a parallelism between astrophysical and laboratory plasma configurations, where small-scale structures can be found. We will focus our attention on the morphology of the radio-jets, on their coupling with the accretion disks and on the possible triggering phenomena, viewed as profiles of plasma instabilities.

  7. Axial Plasma Jet Characterization on a Microsecond X-Pinch

    NASA Astrophysics Data System (ADS)

    Jaar, G. S.; Appartaim, R. K.

    2016-10-01

    The plasma jets generated from a two wire x-pinch have been studied with current quarter period of 1 μs. Wires of tungsten, aluminum, and titanium of 25-100 μm thicknesses have been exploded with a peak current value of 350kA. The plasma has been characterized using Nd:YAG based schlieren photography, time-resolved optical photography, x-ray photodiode detector, and a flat crystal x-ray spectrometer. The schlieren photographs enable determination of the evolution and velocity of the jets. Plasma temperature and density measurements at the crossing point will also be reported from the crystal spectrometer. This research is supported by the US DOE.

  8. Liquid jet breakup regimes at supercritical pressures

    DOE PAGES

    Oefelein, Joseph C.; Dahms, Rainer Norbert Uwe

    2015-07-23

    Previously, a theory has been presented that explains how discrete vapor–liquid interfaces become diminished at certain high-pressure conditions in a manner that leads to well known qualitative trends observed from imaging in a variety of experiments. Rather than surface tension forces, transport processes can dominate over relevant ranges of conditions. In this paper, this framework is now generalized to treat a wide range of fuel-oxidizer combinations in a manner consistent with theories of capillary flows and extended corresponding states theory. Different flow conditions and species-specific molecular properties are shown to produce distinct variations of interfacial structures and local free molecularmore » paths. These variations are shown to occur over the operating ranges in a variety of propulsion and power systems. Despite these variations, the generalized analysis reveals that the envelope of flow conditions at which the transition from classical sprays to diffusion-dominated mixing occurs exhibits a characteristic shape for all liquid–gas combinations. As a result, for alkane-oxidizer mixtures, it explains that these conditions shift to higher pressure flow conditions with increasing carbon number and demonstrates that, instead of widely assumed classical spray atomization, diffusion-dominated mixing may occur under relevant high-pressure conditions in many modern devices.« less

  9. Liquid jet breakup regimes at supercritical pressures

    SciTech Connect

    Oefelein, Joseph C.; Dahms, Rainer Norbert Uwe

    2015-07-23

    Previously, a theory has been presented that explains how discrete vapor–liquid interfaces become diminished at certain high-pressure conditions in a manner that leads to well known qualitative trends observed from imaging in a variety of experiments. Rather than surface tension forces, transport processes can dominate over relevant ranges of conditions. In this paper, this framework is now generalized to treat a wide range of fuel-oxidizer combinations in a manner consistent with theories of capillary flows and extended corresponding states theory. Different flow conditions and species-specific molecular properties are shown to produce distinct variations of interfacial structures and local free molecular paths. These variations are shown to occur over the operating ranges in a variety of propulsion and power systems. Despite these variations, the generalized analysis reveals that the envelope of flow conditions at which the transition from classical sprays to diffusion-dominated mixing occurs exhibits a characteristic shape for all liquid–gas combinations. As a result, for alkane-oxidizer mixtures, it explains that these conditions shift to higher pressure flow conditions with increasing carbon number and demonstrates that, instead of widely assumed classical spray atomization, diffusion-dominated mixing may occur under relevant high-pressure conditions in many modern devices.

  10. The production mechanisms of OH radicals in a pulsed direct current plasma jet

    SciTech Connect

    Liu, X. Y.; Pei, X. K.; Lu, X. P.; Liu, D. W.; Ostrikov, K.

    2014-09-15

    The production mechanism of OH radicals in a pulsed DC plasma jet is studied by a two-dimensional (2-D) plasma jet model and a one-dimensional (1-D) discharge model. For the plasma jet in the open air, electron-impact dissociation of H{sub 2}O, electron neutralization of H{sub 2}O{sup +}, as well as dissociation of H{sub 2}O by O(1D) are found to be the main reactions to generate the OH species. The contribution of the dissociation of H{sub 2}O by electron is more than the others. The additions of N{sub 2}, O{sub 2}, air, and H{sub 2}O into the working gas increase the OH density outside the tube slightly, which is attributed to more electrons produced by Penning ionization. On the other hand, the additions of O{sub 2} and H{sub 2}O into the working gas increase the OH density inside the tube substantially, which is attributed to the increased O (1D) and H{sub 2}O concentration, respectively. The gas flow will transport high density OH out of the tube during pulse off period. It is also shown that the plasma chemistry and reactivity can be effectively controlled by the pulse numbers. These results are supported by the laser induced fluorescence measurements and are relevant to several applications of atmospheric-pressure plasmas in health care, medicine, and materials processing.

  11. First Production of C60 Nanoparticle Plasma Jet for Study of Disruption Mitigation for ITER

    NASA Astrophysics Data System (ADS)

    Bogatu, I. N.; Thompson, J. R.; Galkin, S. A.; Kim, J. S.; Brockington, S.; Case, A.; Messer, S. J.; Witherspoon, F. D.

    2012-10-01

    Unique fast response and large mass-velocity delivery of nanoparticle plasma jets (NPPJs) provide a novel application for ITER disruption mitigation, runaway electrons diagnostics and deep fueling. NPPJs carry a much larger mass than usual gases. An electromagnetic plasma gun provides a very high injection velocity (many km/s). NPPJ has much higher ram pressure than any standard gas injection method and penetrates the tokamak confining magnetic field. Assimilation is enhanced due to the NP large surface-to-volume ratio. Radially expanding NPPJs help achieving toroidal uniformity of radiation power. FAR-TECH's NPPJ system was successfully tested: a coaxial plasma gun prototype (˜35 cm length, 96 kJ energy) using a solid state TiH2/C60 pulsed power cartridge injector produced a hyper-velocity (>4 km/s), high-density (>10^23 m-3), C60 plasma jet in ˜0.5 ms, with ˜1-2 ms overall response-delivery time. We present the TiH2/C60 cartridge injector output characterization (˜180 mg of sublimated C60 gas) and first production results of a high momentum C60 plasma jet (˜0.6 g.km/s).

  12. Plasma-Jet-Driven Magneto-Inertial Fusion (PJMIF): Physics and Design for a Plasma Liner Formation Experiment

    NASA Astrophysics Data System (ADS)

    Hsu, Scott; Cassibry, Jason; Witherspoon, F. Douglas

    2014-10-01

    Spherically imploding plasma liners are a potential standoff compression driver for magneto-inertial fusion, which is a hybrid of and operates in an intermediate density between those of magnetic and inertial fusion. We propose to use an array of merging supersonic plasma jets to form a spherically imploding plasma liner. The jets are to be formed by pulsed coaxial guns with contoured electrodes that are placed sufficiently far from the location of target compression such that no hardware is repetitively destroyed. As such, the repetition rate can be higher (e.g., 1 Hz) and ultimately the power-plant economics can be more attractive than most other MIF approaches. During the R&D phase, a high experimental shot rate at reasonably low cost (e.g., < 1 k/shot) may be achieved with excellent diagnostic access, thus enabling a rapid learning rate. After some background on PJMIF and its prospects for reactor-relevant energy gain, this poster describes the physics objectives and design of a proposed 60-gun plasma-liner-formation experiment, which will provide experimental data on: (i) scaling of peak liner ram pressure versus initial jet parameters, (ii) liner non-uniformity characterization and control, and (iii) control of liner profiles for eventual gain optimization.

  13. Biomedical Applications of Low Temperature Atmospheric Pressure Plasmas to Cancerous Cell Treatment and Tooth Bleaching

    NASA Astrophysics Data System (ADS)

    Lee, Jae Koo; Kim, Myoung Soo; Byun, June Ho; Kim, Kyong Tai; Kim, Gyoo Cheon; Park, Gan Young

    2011-08-01

    Low temperature atmospheric pressure plasmas have attracted great interests and they have been widely applied to biomedical applications to interact with living tissues, cells, and bacteria due to their non-thermal property. This paper reviews the biomedical applications of low temperature atmospheric pressure plasmas to cancerous cell treatment and tooth bleaching. Gold nanoparticles conjugated with cancer-specific antibodies have been introduced to cancerous cells to enhance selective killing of cells, and the mechanism of cell apoptosis induced by plasma has been investigated. Tooth exposed to helium plasma jet with hydrogen peroxide has become brighter and the productions of hydroxyl radicals from hydrogen peroxide have been enhanced by plasma exposure.

  14. A study of real jet effects on the surface pressure distribution induced by a jet in a crossflow

    NASA Technical Reports Server (NTRS)

    Perkins, S. C., Jr.; Mendenhall, M. R.

    1981-01-01

    A study of jet exit profile, exit Mach number, swirl and turbulence level on jet-induced loadings for jets exhausting from a surface into a crossflow is presented. The importance of each of these real jet characteristics is assessed using available data. Where adequate surface pressure distribution data are available, a correlation method to predict surface pressure for a jet exhausting from an infinite flat plate is used either to attempt to develop a correlation based on the real jet characteristics or to model the effects of that characteristic. Data comparisons are presented for selected cases. Also, a summary of information on surface pressure distribution data for jet exhausting from flat plates into a subsonic crossflow is presented.

  15. Divertor plasma conditions and neutral dynamics in horizontal and vertical divertor configurations in JET-ILW low confinement mode plasmas

    NASA Astrophysics Data System (ADS)

    Groth, M.; Brezinsek, S.; Belo, P.; Brix, M.; Calabro, G.; Chankin, A.; Clever, M.; Coenen, J. W.; Corrigan, G.; Drewelow, P.; Guillemaut, C.; Harting, D.; Huber, A.; Jachmich, S.; Järvinen, A.; Kruezi, U.; Lawson, K. D.; Lehnen, M.; Maggi, C. F.; Marchetto, C.; Marsen, S.; Maviglia, F.; Meigs, A. G.; Moulton, D.; Silva, C.; Stamp, M. F.; Wiesen, S.

    2015-08-01

    Measurements of the plasma conditions at the low field side target plate in JET ITER-like wall ohmic and low confinement mode plasmas show minor differences in divertor plasma configurations with horizontally and vertically inclined targets. Both the reduction of the electron temperature in the vicinity of the strike points and the rollover of the ion current to the plates follow the same functional dependence on the density at the low field side midplane. Configurations with vertically inclined target plates, however, produce twice as high sub-divertor pressures for the same upstream density. Simulations with the EDGE2D-EIRENE code package predict significantly lower plasma temperatures at the low field side target in vertical than in horizontal target configurations. Including cross-field drifts and imposing a pumping by-pass leak at the low-field side plate can still not recover the experimental observations.

  16. Experiments with an rf dusty plasma and an external plasma jet

    SciTech Connect

    Ticos, C. M.

    2010-12-14

    A plasma jet produced in a coaxial plasma gun was aimed at a cloud of dust particles levitated in the sheath of a radio-frequency (rf) plasma produced between two parallel-plate electrodes. A high-speed camera with a side-view on the dust cloud was used to track the dust particles. Several cases of dust motion could be observed. When the jet was parallel with the horizontal electrodes of the rf plasma the dust particles were either pushed out of the trapping region by the plasma jet or were only perturbed from their equilibrium position, oscillating with a frequency of the order of a few kHz. In the first case the trajectory of the dust particles followed the curvature of the sheath. In the second case, when the jet was fired at a small angle with the horizontal electrodes the dust particles hit the bottom electrode and ricocheted back into the sheath. Finally, another situation was observed when the jet perturbed the rf plasma and its sheath and the whole dust crystal fell to the electrode.

  17. Experiments with an rf dusty plasma and an external plasma jet

    NASA Astrophysics Data System (ADS)

    Ticoş, C. M.

    2010-12-01

    A plasma jet produced in a coaxial plasma gun was aimed at a cloud of dust particles levitated in the sheath of a radio-frequency (rf) plasma produced between two parallel-plate electrodes. A high-speed camera with a side-view on the dust cloud was used to track the dust particles. Several cases of dust motion could be observed. When the jet was parallel with the horizontal electrodes of the rf plasma the dust particles were either pushed out of the trapping region by the plasma jet or were only perturbed from their equilibrium position, oscillating with a frequency of the order of a few kHz. In the first case the trajectory of the dust particles followed the curvature of the sheath. In the second case, when the jet was fired at a small angle with the horizontal electrodes the dust particles hit the bottom electrode and ricocheted back into the sheath. Finally, another situation was observed when the jet perturbed the rf plasma and its sheath and the whole dust crystal fell to the electrode.

  18. Risk assessment of a cold argon plasma jet in respect to its mutagenicity.

    PubMed

    Wende, K; Bekeschus, S; Schmidt, A; Jatsch, L; Hasse, S; Weltmann, K D; Masur, K; von Woedtke, T

    2016-03-01

    Cold atmospheric pressure plasmas represent a favorable option for the treatment of heat sensitive materials and human or animal tissue. Beneficial effects have been documented in a variety of medical conditions, e.g., in the treatment of chronic wounds. It is assumed that the main mechanism of the plasma's efficacy is mediated by a stimulating dissipation of energy via radiation and/or chemical energy. Although no evidence on undesired side effects of a plasma treatment has yet been presented, skepticism toward the safety of the exposure to plasma is present. However, only little data regarding the mutagenic potential of this new treatment option is available. Accordingly, we investigated the mutagenic potential of an argon plasma jet (kinpen) using different testing systems in accordance with ISO norms and multiple cell lines: a HPRT1 mutation assay, a micronucleus formation assay, and a colony formation assay. Moderate plasma treatment up to 180 s did not increase genotoxicity in any assay or cell type investigated. We conclude that treatment with the argon plasma jet kinpen did not display a mutagenic potential under the test conditions applied and may from this perspective be regarded as safe for the use in biomedical applications.

  19. A handheld low temperature atmospheric pressure air plasma gun for nanomaterial synthesis in liquid phase

    SciTech Connect

    Yu, Shuang; Wang, Kaile; Zuo, Shasha; Liu, Jiahui; Zhang, Jue Fang, Jing

    2015-10-15

    A handheld low temperature atmospheric pressure air plasma gun based on a dielectric barrier structure with hollow electrodes was proposed. The portable plasma gun with an embedded mini air pump was driven by a 12 V direct voltage battery. The air plasma jet generated from the gun could be touched without a common shock hazard. Besides working in air, the plasma gun can also work in water. The diagnostic result of optical emission spectroscopy showed the difference in reactive species of air plasma jet between in air and in water. The plasma gun was excited in 20 ml chloroauric acid aqueous solution with a concentration of 1.214 mM. A significant amount of gold nanoparticles were synthesized after 2 min continuous discharge. The plasma gun with these unique features is applicable in plasma medicine, etching, and s-nthesis of nanomaterials.

  20. A handheld low temperature atmospheric pressure air plasma gun for nanomaterial synthesis in liquid phase

    NASA Astrophysics Data System (ADS)

    Yu, Shuang; Wang, Kaile; Zuo, Shasha; Liu, Jiahui; Zhang, Jue; Fang, Jing

    2015-10-01

    A handheld low temperature atmospheric pressure air plasma gun based on a dielectric barrier structure with hollow electrodes was proposed. The portable plasma gun with an embedded mini air pump was driven by a 12 V direct voltage battery. The air plasma jet generated from the gun could be touched without a common shock hazard. Besides working in air, the plasma gun can also work in water. The diagnostic result of optical emission spectroscopy showed the difference in reactive species of air plasma jet between in air and in water. The plasma gun was excited in 20 ml chloroauric acid aqueous solution with a concentration of 1.214 mM. A significant amount of gold nanoparticles were synthesized after 2 min continuous discharge. The plasma gun with these unique features is applicable in plasma medicine, etching, and s-nthesis of nanomaterials.

  1. Seed disinfection effect of atmospheric pressure plasma and low pressure plasma on Rhizoctonia solani.

    PubMed

    Nishioka, Terumi; Takai, Yuichiro; Kawaradani, Mitsuo; Okada, Kiyotsugu; Tanimoto, Hideo; Misawa, Tatsuya; Kusakari, Shinichi

    2014-01-01

    Gas plasma generated and applied under two different systems, atmospheric pressure plasma and low pressure plasma, was used to investigate the inactivation efficacy on the seedborne pathogenic fungus, Rhizoctonia solani, which had been artificially introduced to brassicaceous seeds. Treatment with atmospheric plasma for 10 min markedly reduced the R. solani survival rate from 100% to 3% but delayed seed germination. The low pressure plasma treatment reduced the fungal survival rate from 83% to 1.7% after 10 min and the inactivation effect was dependent on the treatment time. The seed germination rate after treatment with the low pressure plasma was not significantly different from that of untreated seeds. The air temperature around the seeds in the low pressure system was lower than that of the atmospheric system. These results suggested that gas plasma treatment under low pressure could be effective in disinfecting the seeds without damaging them.

  2. In situ impedance measurement of microwave atmospheric pressure plasma

    NASA Astrophysics Data System (ADS)

    Lee, S. T.; Nam, W. J.; Lee, J. K.; Yun, G. S.

    2017-04-01

    The impedance of atmospheric pressure argon plasma jets driven by microwave frequency is determined in situ by a novel ‘two frequency method’. In the conventional method of reflection coefficient ({{S}}11) measurement, the frequency of the driving microwave power is scanned, which inevitably affects the plasma characters and leads to uncertainty in the estimated plasma impedance. In our proposed method, the frequency-scanning signal additional to the driving power is used to measure {{S}}11 over a wide frequency range, which enables accurate determination of the plasma impedance based on an equivalent circuit model. The measured resistance and reactance of the plasma increase with the driving power in agreement with the transmission line theory. Based on this in situ measurement of the plasma impedance, the net power coupled to the plasma has been determined. The overall power efficiency remains approximately unchanged around 45% for different input power levels owing to the competing effects between the impedance mismatch and the volume change of the plasma.

  3. Spectroscopic studies of the parameters of plasma jets during their propagation in the background plasma on the PF-3 facility

    NASA Astrophysics Data System (ADS)

    Dan’ko, S. A.; Ananyev, S. S.; Kalinin, Yu G.; Krauz, V. I.; Myalton, V. V.

    2017-04-01

    This paper presents measurement results of neon and helium plasma parameters in axial jets generated in plasma focus discharge. They were obtained in the course of experiments on laboratory modeling of astrophysical jets performed at the PF-3 facility. The plasma concentration was determined according to Stark broadening of spectral lines; the ionization temperature was determined by the average ion charge. The values of the concentration and temperature of jet plasma and background plasma at two distances from the pinch are also presented. In addition, an estimation was made of the heat content losses of the neon and helium jets during their movement through the surrounding medium.

  4. [Investigation of a jet operated in atmospheric pressure argon by optical emission spectroscopy].

    PubMed

    Li, Xue-chen; Bao, Wen-ting; Jia, Peng-ying; Di, Cong; Yuan, Ning

    2014-06-01

    A uniform plasma plume was generated in a coaxial dielectric barrier discharge jet through blowing argon into the ambient air at atmospheric pressure. The plasma plume was uniform along the direction of the gas flow. The length of the plasma plume was investigated as a function of the peak voltage, the driving frequency and the gas flow rate. It was found that with increasing the gas flow rate, the plume length increases when the flow rate is lower than 4 L x min(-1), and decreases when it is higher than 4 L x mic(-1). Under constant gas flow rate, the length of the plasma plume increases with the increase in the peak value of the applied voltage and the driving frequency. According to the discharge theory and based on the analysis of the turbulence and the advection, a qualitative explanation was given for the variance of plume length as functions of the experimental parameters. Results also show that there is a discharge pulse for the plasma plume in every positive half cycle, while there is no pulse in negative half cycle. The coaxial dielectric barrier discharge shows two pulses in every positive half cycle and a pulse in every negative half cycle. Analyzing these experimental phenomena mentioned above, a formation mechanism of the plasma plume was proposed. The optical emission spectra were obtained for both the coaxial dielectric barrier discharge and the plasma plume. There was no apparent difference except that some emission lines from reactive species such as OH and N2 were found in the plasma plume. Using the first negative band of, the rational temperature of the plasma plume was measured. Results show that the rational temperature of the plasma plume decreases away from the jet nozzle, and increases with increasing the peak value of the applied voltage.

  5. Jet fire consequence modeling for high-pressure gas pipelines

    NASA Astrophysics Data System (ADS)

    Coccorullo, Ivano; Russo, Paola

    2016-12-01

    A simple and reliable approach for sizing the hazard area potentially affected by a jet fire as consequence of the failure of high-pressure pipeline is proposed. A release rate model, taking pipeline operation properties and source release properties into account, is coupled with SLAB dispersion model and point source radiation model to calculate the hazard distance. The hazard distance is set beyond the distance at which a low chance of fatality can occur to people exposed and a wooden structure is not expected to burn due to radiation heat of jet fire. The comparison between three gases with different physico-chemical properties (i.e. natural gas, hydrogen, ethylene) is shown. The influence of pipeline operating parameters, such as: pressure, pipeline diameter and length, hole size, on the hazard area for the three gases is evaluated. Finally, a simple correlation is proposed for calculating the hazard distance as function of these parameters.

  6. Particle in cell simulation of a radiofrequency plasma jet expanding in vacuum

    SciTech Connect

    Charles, C. Hawkins, R.; Boswell, R. W.

    2015-03-02

    The effect of a pressure gradient (∼133 Pa–0.133 Pa) on electron and ion energy distributions in a radiofrequency (rf at 13.56 MHz) argon plasma jet is studied using a 1D-3v Particle In Cell (PIC) simulation. The PIC domain is three times that of the 0.018 m long plasma cavity and the total simulation time is 1 ms. Ion heating and acceleration up to a drift velocity about 2000 m s{sup −1} are measured along the jet's main expansion axis. Elastic and charge exchange ion-neutral collisions histograms computed at equilibrium during 0.74 ms show that charge exchange collisions act as the main neutral heating mechanism.

  7. Particle in cell simulation of a radiofrequency plasma jet expanding in vacuum

    NASA Astrophysics Data System (ADS)

    Charles, C.; Hawkins, R.; Boswell, R. W.

    2015-03-01

    The effect of a pressure gradient (˜133 Pa-0.133 Pa) on electron and ion energy distributions in a radiofrequency (rf at 13.56 MHz) argon plasma jet is studied using a 1D-3v Particle In Cell (PIC) simulation. The PIC domain is three times that of the 0.018 m long plasma cavity and the total simulation time is 1 ms. Ion heating and acceleration up to a drift velocity about 2000 m s-1 are measured along the jet's main expansion axis. Elastic and charge exchange ion-neutral collisions histograms computed at equilibrium during 0.74 ms show that charge exchange collisions act as the main neutral heating mechanism.

  8. Radiation from high-intensity ultrashort-laser-pulse and gas-jet magnetized plasma interaction.

    PubMed

    Dorranian, Davoud; Starodubtsev, Mikhail; Kawakami, Hiromichi; Ito, Hiroaki; Yugami, Noboru; Nishida, Yasushi

    2003-08-01

    Using a gas-jet flow, via the interaction between an ultrashort high-intensity laser pulse and plasma in the presence of a perpendicular external dc magnetic field, the short pulse radiation from a magnetized plasma wakefield has been observed. Different nozzles are used in order to generate different densities and gas profiles. The neutral density of the gas-jet flow measured with a Mach-Zehnder interferometer is found to be proportional to back pressure of the gas jet in the range of 1 to 8 atm. Strength of the applied dc magnetic field varies from 0 to 8 kG at the interaction region. The frequency of the emitted radiation with the pulse width of 200 ps (detection limit) is in the millimeter wave range. Polarization and spatial distributions of the experimental data are measured to be in good agreement with the theory based on the V(p)xB radiation scheme, where V(p) is the phase velocity of the electron plasma wave and B is the steady magnetic field intensity. Characteristics of the radiation are extensively studied as a function of plasma density and magnetic field strength. These experiments should contribute to the development of a new kind of millimeter wavelength radiation source that is tunable in frequency, pulse duration, and intensity.

  9. Precision optical asphere fabrication by plasma jet chemical etching (PJCE) and ion beam figuring

    NASA Astrophysics Data System (ADS)

    Schindler, Axel; Boehm, Georg; Haensel, Thomas; Frank, Wilfried; Nickel, Andreas; Rauschenbach, Bernd; Bigl, Frieder

    2001-12-01

    We develop a Plasma Jet Chemical Etching (PJCE) technique for high rate precision machining of optical materials aiming in a technology mature for precision asphere and free-form surface topology fabrication. The present contribution summarizes the achievements after about twelve months experience with a prototype production tool facility. PJCE is performed with the help of a microwave driven reactive plasma-jet working in a broad pressure range (10-600 mbar). We developed a moveable lightweight microwave plasma jet source for dwell time techniques performed in a roughly pumped process chamber equipped with a six axis system for precision workpiece and plasma source movement. Volume etch rates of some 10 mm3/min have been achieved for fused silica and silicon, respectively, using reactive (CF4,SF6,O2) and inert (Ar,He) gas mixtures and applying a microwave (2.45 GHz) power in the 100-200 W range. Large quartz plates (80-160 mm) have been figured using dwell time methods to achieve aspheric deformations of some 10 micrometers . The figured surfaces show shape errors of 1-2 micrometers and a microroughness of 50-100 nm RMS but no sub-surface damage enabling a small tool shape conserving post polishing up to the sub-nanometer roughness level. Thus, surface shaping to the nanometer error range can be done by ion beam finishing.

  10. Measurements of the stagnation pressure in the center of a cavitating jet

    NASA Astrophysics Data System (ADS)

    Nobel, A. J.; Talmon, A. M.

    2012-02-01

    The stagnation pressure at a certain distance from the nozzle is important for the erosion/ cutting capacity of a submerged jet in dredging. The decay of the stagnation pressure with jet distance is well known in the case of non-cavitating jets. It is also known that cavitation causes the rate of decay to decrease. Under conditions of cavitation, a cone of bubbles forms around the jet, which decreases the momentum exchange between the jet and the ambient water and the associated entrainment. Despite the amount of research on cavitating jets, the literature does not provide a description for the entrainment in the case of a cavitating jet. Also, a useful description of the stagnation pressure decay of a cavitating jet is missing. To fill this lacuna, we carried out jet tests at various ambient pressures in both fresh and saline water. We present and analyse the results in this paper.

  11. Beryllium migration in JET ITER-like wall plasmas

    NASA Astrophysics Data System (ADS)

    Brezinsek, S.; Widdowson, A.; Mayer, M.; Philipps, V.; Baron-Wiechec, P.; Coenen, J. W.; Heinola, K.; Huber, A.; Likonen, J.; Petersson, P.; Rubel, M.; Stamp, M. F.; Borodin, D.; Coad, J. P.; Carrasco, A. G.; Kirschner, A.; Krat, S.; Krieger, K.; Lipschultz, B.; Linsmeier, Ch.; Matthews, G. F.; Schmid, K.; contributors, JET

    2015-06-01

    JET is used as a test bed for ITER, to investigate beryllium migration which connects the lifetime of first-wall components under erosion with tokamak safety, in relation to long-term fuel retention. The (i) limiter and the (ii) divertor configurations have been studied in JET-ILW (JET with a Be first wall and W divertor), and compared with those for the former JET-C (JET with carbon-based plasma-facing components (PFCs)). (i) For the limiter configuration, the Be gross erosion at the contact point was determined in situ by spectroscopy as between 4% (Ein = 35 eV) and more than 100%, caused by Be self-sputtering (Ein = 200 eV). Chemically assisted physical sputtering via BeD release has been identified to contribute to the effective Be sputtering yield, i.e. at Ein = 75 eV, erosion was enhanced by about 1/3 with respect to the bare physical sputtering case. An effective gross yield of 10% is on average representative for limiter plasma conditions, whereas a factor of 2 difference between the gross erosion and net erosion, determined by post-mortem analysis, was found. The primary impurity source in the limiter configuration in JET-ILW is only 25% higher (in weight) than that for the JET-C case. The main fraction of eroded Be stays within the main chamber. (ii) For the divertor configuration, neutral Be and BeD from physically and chemically assisted physical sputtering by charge exchange neutrals and residual ion flux at the recessed wall enter the plasma, ionize and are transported by scrape-off layer flows towards the inner divertor where significant net deposition takes place. The amount of Be eroded at the first wall (21 g) and the Be amount deposited in the inner divertor (28 g) are in fair agreement, though the balancing is as yet incomplete due to the limited analysis of PFCs. The primary impurity source in the JET-ILW is a factor of 5.3 less in comparison with that for JET-C, resulting in lower divertor material deposition, by more than one order of

  12. Revealing plasma oscillation in THz spectrum from laser plasma of molecular jet.

    PubMed

    Li, Na; Bai, Ya; Miao, Tianshi; Liu, Peng; Li, Ruxin; Xu, Zhizhan

    2016-10-03

    Contribution of plasma oscillation to the broadband terahertz (THz) emission is revealed by interacting two-color (ω/2ω) laser pulses with a supersonic jet of nitrogen molecules. Temporal and spectral shifts of THz waves are observed as the plasma density varies. The former owes to the changing refractive index of the THz waves, and the latter correlates to the varying plasma frequency. Simulation of considering photocurrents, plasma oscillation and decaying plasma density explains the broadband THz spectrum and the varying THz spectrum. Plasma oscillation only contributes to THz waves at low plasma density owing to negligible plasma absorption. At the longer medium or higher density, the combining effects of plasma oscillation and absorption results in the observed low-frequency broadband THz spectra.

  13. Functionalization of carbon nanowalls by plasma jet in liquid treatment

    NASA Astrophysics Data System (ADS)

    Ionita, Maria D.; Vizireanu, Sorin; Stoica, Silviu D.; Ionita, Mariana; Pandele, Andreea M.; Cucu, Ana; Stamatin, Ioan; Nistor, Leona C.; Dinescu, Gheorghe

    2016-02-01

    Submerged in liquid plasma treatment is a new approach for nanomaterials functionalization. This paper presents a surfactant free method for functionalization of graphene nano-platelets derived from carbon nanowalls through plasma jet treatment of their water suspensions. The untreated and under-liquid plasma treated suspensions were characterized in terms of their UV-Vis absorption, zeta-size, zeta-potential, pH, and conductivity. Investigation of dried material revealed that the graphene nano-sheets morphology and structure have been preserved, showing also new oxygen functional groups bonded to the carbon network after in liquid plasma treatment. The results demonstrate the efficiency of this technique in changing the properties of carbon nanowalls suspensions and also in getting functionalized multilayered graphene sheets.

  14. Improved performance of a barrier-discharge plasma jet biased by a direct-current voltage.

    PubMed

    Li, Xuechen; Li, Yaru; Zhang, Panpan; Jia, Pengying; Dong, Lifang

    2016-10-19

    One of the challenges that plasma research encounters is how to generate a large-scale plasma plume at atmospheric pressure. Through utilizing a third electrode biased by a direct-current voltage, a longer plasma plume is generated by a plasma jet in dielectric barrier discharge configurations. Results indicate that the plume length increases until it reaches the third electrode with increasing the bias voltage. By fast photography, it is found that the plume consists of two types of streamers under the influence of the bias voltage, which develops from a guided streamer to a branching one with leaving the tube opening. The transition from the guided streamer to the branching one can be attributed to the electric field and the air/argon fraction.

  15. Improved performance of a barrier-discharge plasma jet biased by a direct-current voltage

    NASA Astrophysics Data System (ADS)

    Li, Xuechen; Li, Yaru; Zhang, Panpan; Jia, Pengying; Dong, Lifang

    2016-10-01

    One of the challenges that plasma research encounters is how to generate a large-scale plasma plume at atmospheric pressure. Through utilizing a third electrode biased by a direct-current voltage, a longer plasma plume is generated by a plasma jet in dielectric barrier discharge configurations. Results indicate that the plume length increases until it reaches the third electrode with increasing the bias voltage. By fast photography, it is found that the plume consists of two types of streamers under the influence of the bias voltage, which develops from a guided streamer to a branching one with leaving the tube opening. The transition from the guided streamer to the branching one can be attributed to the electric field and the air/argon fraction.

  16. Improved performance of a barrier-discharge plasma jet biased by a direct-current voltage

    PubMed Central

    Li, Xuechen; Li, Yaru; Zhang, Panpan; Jia, Pengying; Dong, Lifang

    2016-01-01

    One of the challenges that plasma research encounters is how to generate a large-scale plasma plume at atmospheric pressure. Through utilizing a third electrode biased by a direct-current voltage, a longer plasma plume is generated by a plasma jet in dielectric barrier discharge configurations. Results indicate that the plume length increases until it reaches the third electrode with increasing the bias voltage. By fast photography, it is found that the plume consists of two types of streamers under the influence of the bias voltage, which develops from a guided streamer to a branching one with leaving the tube opening. The transition from the guided streamer to the branching one can be attributed to the electric field and the air/argon fraction. PMID:27759080

  17. Thomson scattering measurement of a collimated plasma jet generated by a high-power laser system

    NASA Astrophysics Data System (ADS)

    Ishikawa, T.; Sakawa, Y.; Morita, T.; Yamaura, Y.; Kuramitsu, Y.; Moritaka, T.; Sano, T.; Shimoda, R.; Tomita, K.; Uchino, K.; Matsukiyo, S.; Mizuta, A.; Ohnishi, N.; Crowston, R.; Woolsey, N.; Doyle, H.; Gregori, G.; Koenig, M.; Michaut, C.; Pelka, A.; Yuan, D.; Li, Y.; Zhang, K.; Zhong, J.; Wang, F.; Takabe, H.

    2016-03-01

    One of the important and interesting problems in astrophysics and plasma physics is collimation of plasma jets. The collimation mechanism, which causes a plasma flow to propagate a long distance, has not been understood in detail. We have been investigating a model experiment to simulate astrophysical plasma jets with an external magnetic field [Nishio et al., EPJ. Web of Conferences 59, 15005 (2013)]. The experiment was performed by using Gekko XII HIPER laser system at Institute of Laser Engineering, Osaka University. We shot CH plane targets (3 mm × 3 mm × 10 μm) and observed rear-side plasma flows. A collimated plasma flow or plasma jet was generated by separating focal spots of laser beams. In this report, we measured plasma jet structure without an external magnetic field with shadowgraphy, and simultaneously measured the local parameters of the plasma jet, i.e., electron density, electron and ion temperatures, charge state, and drift velocity, with collective Thomson scattering.

  18. Dynamics of Magnetized Plasma Jets and Bubbles Launched into a Background Magnetized Plasma

    NASA Astrophysics Data System (ADS)

    Wallace, B.; Zhang, Y.; Fisher, D. M.; Gilmore, M.

    2016-10-01

    The propagation of dense magnetized plasma, either collimated with mainly azimuthal B-field (jet) or toroidal with closed B-field (bubble), in a background plasma occurs in a number of solar and astrophysical cases. Such cases include coronal mass ejections moving in the background solar wind and extragalactic radio lobes expanding into the extragalactic medium. Understanding the detailed MHD behavior is crucial for correctly modeling these events. In order to further the understanding of such systems, we are investigating the injection of dense magnetized jets and bubbles into a lower density background magnetized plasma using a coaxial plasma gun and a background helicon or cathode plasma. In both jet and bubble cases, the MHD dynamics are found to be very different when launched into background plasma or magnetic field, as compared to vacuum. In the jet case, it is found that the inherent kink instability is stabilized by velocity shear developed due to added magnetic tension from the background field. In the bubble case, rather than directly relaxing to a minimum energy Taylor state (spheromak) as in vacuum, there is an expansion asymmetry and the bubble becomes Rayleigh-Taylor unstable on one side. Recent results will be presented. Work supported by the Army Research Office Award No. W911NF1510480.

  19. Experimental, Numerical and Analytical Studies of the MHD-driven plasma jet, instabilities and waves

    NASA Astrophysics Data System (ADS)

    Zhai, Xiang

    This thesis describes a series of experimental, numerical, and analytical studies involving the Caltech magnetohydrodynamically (MHD)-driven plasma jet experiment. The plasma jet is created via a capacitor discharge that powers a magnetized coaxial planar electrodes system. The jet is collimated and accelerated by the MHD forces. We present three-dimensional ideal MHD finite-volume simulations of the plasma jet experiment using an astrophysical magnetic tower as the baseline model. A compact magnetic energy/helicity injection is exploited in the simulation analogous to both the experiment and to astrophysical situations. Detailed analysis provides a comprehensive description of the interplay of magnetic force, pressure, and flow effects. We delineate both the jet structure and the transition process that converts the injected magnetic energy to other forms. When the experimental jet is sufficiently long, it undergoes a global kink instability and then a secondary local Rayleigh-Taylor instability caused by lateral acceleration of the kink instability. We present an MHD theory of the Rayleigh-Taylor instability on the cylindrical surface of a plasma flux rope in the presence of a lateral external gravity. The Rayleigh-Taylor instability is found to couple to the classic current-driven instability, resulting in a new type of hybrid instability. The coupled instability, produced by combination of helical magnetic field, curvature of the cylindrical geometry, and lateral gravity, is fundamentally different from the classic magnetic Rayleigh-Taylor instability occurring at a two-dimensional planar interface. In the experiment, this instability cascade from macro-scale to micro-scale eventually leads to the failure of MHD. When the Rayleigh-Taylor instability becomes nonlinear, it compresses and pinches the plasma jet to a scale smaller than the ion skin depth and triggers a fast magnetic reconnection. We built a specially designed high-speed 3D magnetic probe and

  20. Z-pinch Plasma Temperature and Implosion Velocity from Laboratory Plasma Jets using Thomson Scattering

    NASA Astrophysics Data System (ADS)

    Banasek, Jacob; Byvank, Tom; Kusse, Bruce; Hammer, David

    2016-10-01

    We discuss the use of collective Thomson scattering to determine the implosion velocity and other properties of laboratory plasma jets. The plasma jet is created using a 1 MA pulsed power machine with a 15 μm Al radial foil load. The Thomson scattering laser has a maximum energy of 10 J at 526.5 nm with a pulse duration of 3 ns. Using a time gated ICCD camera and spectrometer system we are able to record the scattered spectrum from 9 or 18 regions along the laser path with sub-mm spatial resolution. Collecting scattered radiation from the same area at two different angles simultaneously enables determination of both the radial and azimuthal velocities. The scattered spectrum for non-magnetized jets indicates a radial implosion velocity of 27 km/s into the jets. A determination of ion and electron temperatures from the scattered spectrum is in progress. Comparing results using a laser energy of 10 J and 1 J shows noticeable effects on plasma jet properties when using 10 J. Therefore the lower laser energy must be used to determine the plasma properties. This research is supported by the NNSA Stewardship Sciences Academic Programs under DOE Cooperative Agreement DE-NA0001836.

  1. Electron density in amplitude modulated microwave atmospheric plasma jet as determined from microwave interferometry and emission spectroscopy

    NASA Astrophysics Data System (ADS)

    Faltýnek, J.; Hnilica, J.; Kudrle, V.

    2017-01-01

    Time resolved electron density in an atmospheric pressure amplitude modulated microwave plasma jet is determined using the microwave interferometry method, refined by numerical modelling of the propagation of non-planar electromagnetic waves in the vicinity of a small diameter, dense collisional plasma filament. The results are compared to those from the Stark broadening of the {{\\text{H}}β} emission line. Both techniques show, both qualitatively and quantitatively, a similar temporal evolution of electron density during one modulation period.

  2. Study of the LTE departure in a low pressure supersonic plasma jet in Ar-H{sub 2} and in Ar-N{sub 2}-H{sub 2} mixture

    SciTech Connect

    Rajabian, M.; Vacquie, S.; Gravelle, D.V.

    1999-07-01

    Plasma torches at low pressure and controlled atmosphere are used in major applications for the production and processing of materials due to their potential for high performance, and low contamination. A good knowledge of the plasma parameters is necessary, particularly for the design of high-performance mathematical models that avoid the building of expensive prototypes for performance assessment. The present work is undertaken on a DC plasma torch operating over a wide pressure range (8 kPa to 100 kPa) at an arc power fixed at 17.5 kW. Emission spectroscopy diagnostics was carried out for determining temperature, electron and particle density profiles in two gas mixtures: Ar-N{sub 2}-H{sub 2} with flow rates of 40, 10, and 1 slpm respectively, and Ar-H{sub 2} with input flow rates of 35 and 7 slpm respectively. For the gas mixtures used, the supersonic shock occurs at a distance from the nozzle exit growing when the pressure decreases (8, 10, and 13 mm for pressures of 13, 20 and 26 kPa). For pressures of 100 kPa and 53 kPa, they observe a good agreement between the values of electron density Ne experimentally measured independently of local thermodynamic equilibrium (LTE) and the values obtained by calculation using the temperature obtained with Boltzmann diagram. Local thermodynamic equilibrium conditions prevail at these values of pressure. For the lower values of the pressure, the experimental value of N{sub 2}{sup {minus}} ion density are higher than the calculated values, using the rotational temperature T{sub h}, or the Boltzmann temperature T{sub e}. The discrepancy is lower with the use of T{sub e}. That shows the importance of the collisions between electrons and heavy particles, due to the high values of the electron density (4.10{sup 16} cm{sup {minus}3} in the supersonic shock wave for 13 kPa). For pressure lower than 26 kPa important deviation from LTE conditions are observed.

  3. OH radicals distribution in an Ar-H{sub 2}O atmospheric plasma jet

    SciTech Connect

    Li, L.; Leys, C.; Nikiforov, A.; Xiong, Q.; Britun, N.; Snyders, R.; Lu, X.

    2013-09-15

    Recently, plasma jet systems found numerous applications in the field of biomedicine and treatment of temperature-sensitive materials. OH radicals are one of the main active species produced by these plasmas. Present study deals with the investigation of RF atmospheric pressure plasma jet in terms of OH radicals production by admixture of H{sub 2}O into argon used as a feed gas. Generation of OH radicals is studied by laser-induced fluorescence spectroscopy. The excitation dynamics of OH radicals induced by the laser photons is studied by time-resolved spectroscopy. It is shown that vibrational and rotational energy transfer processes, which are sensitive to the surrounding species, can lead to the complication in the OH radicals diagnostics at high pressure and have to be considered during experiments. The axial and radial 2D maps of absolute densities of hydroxyl radicals at different water contents are obtained. The highest density of 1.15 × 10{sup 20} m{sup −3} is measured in the plasma core for the case of 0.3% H{sub 2}O. In the x–y-plane, the OH density steeply decreases within a range of ±2 mm from its maximum value down to 10{sup 18} m{sup −3}. The effect of H{sub 2}O addition on the generation of OH radicals is investigated and discussed.

  4. Study and application of a high-pressure water jet multi-functional flow test system.

    PubMed

    Shi, Huaizhong; Li, Gensheng; Huang, Zhongwei; Li, Jingbin; Zhang, Yi

    2015-12-01

    As the exploration and development of oil and gas focus more and more on deeper formation, hydraulic issues such as high-pressure water jet rock breaking, wellbore multiphase flow law, cuttings carrying efficiency, and hydraulic fracturing technique during the drilling and completion process have become the key points. To accomplish related researches, a high-pressure water jet multi-functional flow test system was designed. The following novel researches are carried out: study of high-pressure water jet characteristics under confining pressure, wellbore multiphase flow regime, hydraulic pressure properties of down hole tools during jet fracturing and pulsed cavitation jet drilling, and deflector's friction in radial jet drilling. The validity and feasibility of the experimental results provided by the system with various test modules have proved its importance in the research of the high-pressure water jet and well completion technology.

  5. Study and application of a high-pressure water jet multi-functional flow test system

    NASA Astrophysics Data System (ADS)

    Shi, Huaizhong; Li, Gensheng; Huang, Zhongwei; Li, Jingbin; Zhang, Yi

    2015-12-01

    As the exploration and development of oil and gas focus more and more on deeper formation, hydraulic issues such as high-pressure water jet rock breaking, wellbore multiphase flow law, cuttings carrying efficiency, and hydraulic fracturing technique during the drilling and completion process have become the key points. To accomplish related researches, a high-pressure water jet multi-functional flow test system was designed. The following novel researches are carried out: study of high-pressure water jet characteristics under confining pressure, wellbore multiphase flow regime, hydraulic pressure properties of down hole tools during jet fracturing and pulsed cavitation jet drilling, and deflector's friction in radial jet drilling. The validity and feasibility of the experimental results provided by the system with various test modules have proved its importance in the research of the high-pressure water jet and well completion technology.

  6. Diamagnetic effect produced by the Fluxus-1 and -2 artificial plasma jet

    NASA Astrophysics Data System (ADS)

    Gavrilov, B. G.; Podgorny, A. I.; Podgorny, I. M.; Sobyanin, D. B.; Zetzer, J. I.; Erlandson, R. E.; Meng, C.-I.; Stoyanov, B. J.

    The purpose of the Fluxus-1 and -2 active experiments is to study plasma jets injected parallel to the magnetic field and to study the interaction of these jets with the magnetic field. The experiments were conducted using a shaped-charge device, known as an explosive type generator (ETG), that produced an artificial aluminum plasma jet. In Fluxus-1 and -2 the jet was injected nearly parallel to the geomagnetic field at an altitude of 140 km toward an instrumented diagnostic payload located about 100 m away from the ETG. A ∼50% reduction in the magnetic field was observed as the plasma jet passed by the diagnostic payload. Comparisons of 3-dimensional simulation results with the observed magnetic field perturbations suggest that the Fluxus-1 plasma jet was ∼30° from the magnetic field direction while the Fluxus-2 plasma jet was directed nearly parallel to the magnetic field.

  7. Tank pressure control in low gravity by jet mixing

    NASA Technical Reports Server (NTRS)

    Bentz, Michael D.

    1993-01-01

    The Tank Pressure Control Experiment (TPCE) is a space experiment developed to help meet the need for a critical aspect of cryogenic fluid management technology: control of storage tank pressures in the absence of gravity by forced convective mixing. The experiment used a 13.7-liter tank filled to a constant 83 percent level with refrigerant 113 at near saturation conditions to simulate the fluid dynamics and thermodynamics of cryogenic fluids in space applications. The objectives of TPCE were to characterize the fluid dynamics of axial jet-induced mixing in low gravity, to evaluate the validity of empirical mixing models, and to provide data for use in developing and validating computational fluid dynamic models of mixing processes. TPCE accomplished all of its objectives in flight on Space Shuttle Mission STS-3 in August of 1991. The range of flow patterns photographed generally confirmed a prior correlation based on drop tower tests. A closed-form equation derived from a simple thermodynamic model was found to provide a first-order prediction of the pressure reduction time as a function of mixer parameters, tank size, and fluid thermophysical properties. Low energy mixing jets were found to be effective and reliable at reducing thermal non-uniformities, promoting heat and mass transfer between the phases, and reducing tank pressure.

  8. Summarizing results on the performance of a selective set of atmospheric plasma jets for separation of photons and reactive particles

    NASA Astrophysics Data System (ADS)

    Schneider, Simon; Jarzina, Fabian; Lackmann, Jan-Wilm; Golda, Judith; Layes, Vincent; Schulz-von der Gathen, Volker; Bandow, Julia Elisabeth; Benedikt, Jan

    2015-11-01

    A microscale atmospheric-pressure plasma jet is a remote plasma jet, where plasma-generated reactive particles and photons are involved in substrate treatment. Here, we summarize our efforts to develop and characterize a particle- or photon-selective set of otherwise identical jets. In that way, the reactive species or photons can be used separately or in combination to study their isolated or combined effects to test whether the effects are additive or synergistic. The final version of the set of three jets—particle-jet, photon-jet and combined jet—is introduced. This final set realizes the highest reproducibility of the photon and particle fluxes, avoids turbulent gas flow, and the fluxes of the selected plasma-emitted components are almost identical in the case of all jets, while the other component is effectively blocked, which was verified by optical emission spectroscopy and mass spectrometry. Schlieren-imaging and a fluid dynamics simulation show the stability of the gas flow. The performance of these selective jets is demonstrated with the example of the treatment of E. coli bacteria with the different components emitted by a He-only, a He/N2 and a He/O2 plasma. Additionally, measurements of the vacuum UV photon spectra down to the wavelength of 50 nm can be made with the photon-jet and the relative comparison of spectral intensities among different gas mixtures is reported here. The results will show that the vacuum UV photons can lead to the inactivation of the E.coli bacteria.

  9. Research on atmospheric pressure plasma processing sewage

    NASA Astrophysics Data System (ADS)

    Song, Gui-cai; Na, Yan-xiang; Dong, Xiao-long; Sun, Xiao-liang

    2013-08-01

    The water pollution has become more and more serious with the industrial progress and social development, so it become a worldwide leading environmental management problem to human survival and personal health, therefore, countries are looking for the best solution. Generally speaking, in this paper the work has the following main achievements and innovation: (1) Developed a new plasma device--Plasma Water Bed. (2) At atmospheric pressure condition, use oxygen, nitrogen, argon and helium as work gas respectively, use fiber spectrometer to atmospheric pressure plasma discharge the emission spectrum of measurement, due to the different work gas producing active particle is different, so can understand discharge, different particle activity, in the treatment of wastewater, has the different degradation effects. (3) Methyl violet solution treatment by plasma water bed. Using plasma drafting make active particles and waste leachate role, observe the decolorization, measurement of ammonia nitrogen removal.

  10. Adiabatic cooling of the artificial Porcupine plasma jet

    NASA Astrophysics Data System (ADS)

    Ruizhin, Iu. Ia.; Treumann, R. A.; Bauer, O. H.; Moskalenko, A. M.

    1987-01-01

    Measurements of the plasma density obtained during the interaction of the artificial plasma jet, fired into the ionosphere with the body of the Porcupine main payload, have been analyzed for times when there was a well-developed wake effect. Using wake theory, the maximum temperature of the quasi-neutral xenon ion beam has been determined for an intermediate distance from the ion beam source when the beam has left the diamagnetic region but is still much denser than the ionospheric background plasma. The beam temperature is found to be about 4 times less than the temperature at injection. This observation is very well explained by adiabatic cooling of the beam during its initial diamagnetic and current-buildup phases at distances r smaller than 10 m. Outside this region, the beam conserves the temperature achieved. The observation proves that the artificial plasma jet passes through an initial gas-like diamagnetic phase restricted to the vicinity of the beam source, where it expands adiabatically. Partial cooling also takes place outside the diamagnetic region where the beam current still builds up. The observations also support a recently developed current-closure model of the quasi-neutral ion beam.

  11. Healing burns using atmospheric pressure plasma irradiation

    NASA Astrophysics Data System (ADS)

    Hirata, Takamichi; Kishimoto, Takumi; Tsutsui, Chihiro; Kanai, Takao; Mori, Akira

    2014-01-01

    An experiment testing the effects of plasma irradiation with an atmospheric-pressure plasma (APP) reactor on rats given burns showed no evidence of electric shock injuries upon pathology inspection of the irradiated skin surface. In fact, the observed evidence of healing and improvement of the burns suggested healing effects from plasma irradiation. The quantities of neovascular vessels in the living tissues at 7 days were 9.2 ± 0.77 mm-2 without treatment and 18.4 ± 2.9 mm-2 after plasma irradiation.

  12. Flow Control on Low-Pressure Turbine Airfoils Using Vortex Generator Jets

    NASA Technical Reports Server (NTRS)

    Volino, Ralph J.; Ibrahim, Mounir B.; Kartuzova, Olga

    2010-01-01

    Motivation - Higher loading on Low-Pressure Turbine (LPT) airfoils: Reduce airfoil count, weight, cost. Increase efficiency, and Limited by suction side separation. Growing understanding of transition, separation, wake effects: Improved models. Take advantage of wakes. Higher lift airfoils in use. Further loading increases may require flow control: Passive: trips, dimples, etc. Active: plasma actuators, vortex generator jets (VGJs). Can increased loading offset higher losses on high lift airfoils. Objectives: Advance knowledge of boundary layer separation and transition under LPT conditions. Demonstrate, improve understanding of separation control with pulsed VGJs. Produce detailed experimental data base. Test and develop computational models.

  13. Investigation on Plasma Jet Flow Phenomena During DC Air Arc Motion in Bridge-Type Contacts

    NASA Astrophysics Data System (ADS)

    Zhai, Guofu; Bo, Kai; Chen, Mo; Zhou, Xue; Qiao, Xinlei

    2016-05-01

    Arc plasma jet flow in the air was investigated under a bridge-type contacts in a DC 270 V resistive circuit. We characterized the arc plasma jet flow appearance at different currents by using high-speed photography, and two polished contacts were used to search for the relationship between roughness and plasma jet flow. Then, to make the nature of arc plasma jet flow phenomena clear, a simplified model based on magnetohydrodynamic (MHD) theory was established and calculated. The simulated DC arc plasma was presented with the temperature distribution and the current density distribution. Furthermore, the calculated arc flow velocity field showed that the circular vortex was an embodiment of the arc plasma jet flow progress. The combined action of volume force and contact surface was the main reason of the arc jet flow. supported by National Natural Science Foundation of China (Nos. 51307030, 51277038)

  14. Impact of electric field from a plasma jet on biological targets

    NASA Astrophysics Data System (ADS)

    Douat, Claire; Darny, Thibault; Iseni, Sylvain; Damany, Xavier; Dozias, Sebastien; Pouvesle, Jean-Michel; Robert, Eric; Vijayarangan, Vinodini; Delalande, Anthony; Pichon, Chantal

    2016-09-01

    Atmospheric pressure plasma jets have demonstrated their ability in biomedical applications thanks to their low gas temperature and their capacity to produce radicals, ions, electrons, UV radiation and electric fields. However the understanding of the interactions between the plasma and living cells and tissues is still far from being completely understood. Recently, Robert et al characterized two components of the electric field from a plasma jet and showed that the latter can propagate deeply in tissues on several mm. In this work, we focus on the study of the electric field induced by the plasma and its influence on the cell membrane. Propidium iodide, dextran sulfate and plasmid DNA are used to measure the permeability of the membrane, while an electro-optic probe is used to measure the longitudinal and the radial components of the electric field. The two components are both spatially and temporally resolved. To investigate the contribution of the electric field on the cell membrane, a dielectric barrier is used between the plasma and the biological target. A comparison with and without the barrier will be presented for both biological and agriculture applications.

  15. The effect of jet and DBD plasma on NCI-78 blood cancer cells

    NASA Astrophysics Data System (ADS)

    Kaushik, Nagendra K.; Kaushik, Neha; Choi, Eun Ha

    2013-06-01

    In this study we describe the effects of a nonthermal jet and dielectric barrier discharge (DBD) plasma on the T98G brain cancer cell line. The results of this study reveal that the jet and DBD plasma inhibits NCI-78 blood cancer cells growth efficiently with the loss of metabolic viability of cells. The main goal of this study is to induce cell death in NCI-78 blood cancer cells by the toxic effect of jet and DBD plasma.

  16. Plasma jet braking: energy dissipation and nonadiabatic electrons.

    PubMed

    Khotyaintsev, Yu V; Cully, C M; Vaivads, A; André, M; Owen, C J

    2011-04-22

    We report in situ observations by the Cluster spacecraft of wave-particle interactions in a magnetic flux pileup region created by a magnetic reconnection outflow jet in Earth's magnetotail. Two distinct regions of wave activity are identified: lower-hybrid drift waves at the front edge and whistler-mode waves inside the pileup region. The whistler-mode waves are locally generated by the electron temperature anisotropy, and provide evidence for ongoing betatron energization caused by magnetic flux pileup. The whistler-mode waves cause fast pitch-angle scattering of electrons and isotropization of the electron distribution, thus making the flow braking process nonadiabatic. The waves strongly affect the electron dynamics and thus play an important role in the energy conversion chain during plasma jet braking.

  17. Plasma Jet Braking: Energy Dissipation and Nonadiabatic Electrons

    NASA Astrophysics Data System (ADS)

    Khotyaintsev, Yu. V.; Cully, C. M.; Vaivads, A.; André, M.; Owen, C. J.

    2011-04-01

    We report in situ observations by the Cluster spacecraft of wave-particle interactions in a magnetic flux pileup region created by a magnetic reconnection outflow jet in Earth’s magnetotail. Two distinct regions of wave activity are identified: lower-hybrid drift waves at the front edge and whistler-mode waves inside the pileup region. The whistler-mode waves are locally generated by the electron temperature anisotropy, and provide evidence for ongoing betatron energization caused by magnetic flux pileup. The whistler-mode waves cause fast pitch-angle scattering of electrons and isotropization of the electron distribution, thus making the flow braking process nonadiabatic. The waves strongly affect the electron dynamics and thus play an important role in the energy conversion chain during plasma jet braking.

  18. Plasma Jet Braking: Energy Dissipation and Nonadiabatic Electrons

    SciTech Connect

    Khotyaintsev, Yu. V.; Cully, C. M.; Vaivads, A.; Andre, M.; Owen, C. J.

    2011-04-22

    We report in situ observations by the Cluster spacecraft of wave-particle interactions in a magnetic flux pileup region created by a magnetic reconnection outflow jet in Earth's magnetotail. Two distinct regions of wave activity are identified: lower-hybrid drift waves at the front edge and whistler-mode waves inside the pileup region. The whistler-mode waves are locally generated by the electron temperature anisotropy, and provide evidence for ongoing betatron energization caused by magnetic flux pileup. The whistler-mode waves cause fast pitch-angle scattering of electrons and isotropization of the electron distribution, thus making the flow braking process nonadiabatic. The waves strongly affect the electron dynamics and thus play an important role in the energy conversion chain during plasma jet braking.

  19. Pulsating jet-like structures in magnetized plasma

    NASA Astrophysics Data System (ADS)

    Goncharov, V. P.; Pavlov, V. I.

    2016-08-01

    The formation of pulsating jet-like structures has been studied in the scope of the nonhydrostatic model of a magnetized plasma with horizontally nonuniform density. We discuss two mechanisms which are capable of stopping the gravitational spreading appearing to grace the Rayleigh-Taylor instability and to lead to the formation of stationary or oscillating localized structures. One of them is caused by the Coriolis effect in the rotating frames, and another is connected with the Lorentz effect for magnetized fluids. Magnetized jets/drops with a positive buoyancy must oscillate in transversal size and can manifest themselves as "radio pulsars." The estimates of their frequencies are made for conditions typical for the neutron star's ocean.

  20. Nonthermal atmospheric argon plasma jet effects on Escherichia coli biomacromolecules.

    PubMed

    Hosseinzadeh Colagar, Abasalt; Memariani, Hamed; Sohbatzadeh, Farshad; Valinataj Omran, Azadeh

    2013-12-01

    Nonthermal atmospheric plasma jet, a promising technology based on ionized gas at low temperatures, can be applied for disinfection of contaminated surfaces. In this study, Escherichia coli cells and their macromolecules were exposed to the nonthermal atmospheric argon plasma jet for different time durations. Total protein, genomic DNA, and malondialdehyde (MDA) levels of E. coli were assessed by sodium dodecyl sulfate-polyacrylamide gel electrophoresis and silver staining; agarose gel electrophoresis; and measurement of absorbance at 534 nm, respectively. After exposure, the spectroscopic results of liquid samples indicated that the survival reduction of E. coli can reach to 100 % in an exposure time of 600 s. Moreover, inactivation zones of E. coli, DNA degradation, and MDA levels were significantly increased. Additionally, banding patterns of total protein were changed and amino acid concentrations increased following ninhydrin test. The experimental results suggest that the nonthermal plasma could serve as an effective instrument for both sterilizing E. coli and degrading macromolecules from the surface of the objects being sterilized.

  1. Semi-analytic model of plasma-jet-driven magneto-inertial fusion

    NASA Astrophysics Data System (ADS)

    Langendorf, Samuel J.; Hsu, Scott C.

    2017-03-01

    A semi-analytic model for plasma-jet-driven magneto-inertial fusion is presented. Compressions of a magnetized plasma target by a spherically imploding plasma liner are calculated in one dimension (1D), accounting for compressible hydrodynamics and ionization of the liner material, energy losses due to conduction and radiation, fusion burn and alpha deposition, separate ion and electron temperatures in the target, magnetic pressure, and fuel burn-up. Results show 1D gains of 3-30 at spherical convergence ratio <15 and 20-40 MJ of liner energy, for cases in which the liner thickness is 1 cm and the initial radius of a preheated magnetized target is 4 cm. Some exploration of parameter space and physics settings is presented. The yields observed suggest that there is a possibility of igniting additional dense fuel layers to reach high gain.

  2. Optical Characteristics Investigation of the Cold Argon Plasma Jet for the Medical Applications

    NASA Astrophysics Data System (ADS)

    Nguyen-Kuok, Shi; Malakhov, Yury; Bach, Sy Minh; Korotkikh, Ivan

    2016-09-01

    The medical setup was designed for the treatment of wounds, disinfection of inflammation, for the destruction of damaged cells. The results of experimental determination of the optical characteristics of Argon cold plasma at atmospheric pressure are presented in the paper. The main components of the experimental setup are plasma torch, spectrometer, photo-electron multiplier, oscilloscope, gas consumption QAr = 1 - 20 l/min. Spectrum of the plasma jet is obtained using the grating spectrometer Spectra with radiometric calibration, operating in the visible range λ = 380 - 760 nm. The sun-blind photodetector was used for determination of the intensity of radiation in the UV range λ = 190 - 380 nm. The emission spectrum consists of a continuous radiation and the emissions of atoms and ions ArI and ArII. The analysis of spectral lines was carried out.

  3. Exploration of Plasma Jets Approach to High Energy Density Physics. Final report

    SciTech Connect

    Chen, Chiping

    2013-08-26

    High-energy-density laboratory plasma (HEDLP) physics is an emerging, important area of research in plasma physics, nuclear physics, astrophysics, and particle acceleration. While the HEDLP regime occurs at extreme conditions which are often found naturally in space but not on the earth, it may be accessible by colliding high intensity plasmas such as high-energy-density plasma jets, plasmoids or compact toroids from plasma guns. The physics of plasma jets is investigated in the context of high energy density laboratory plasma research. This report summarizes results of theoretical and computational investigation of a plasma jet undergoing adiabatic compression and adiabatic expansion. A root-mean-squared (rms) envelope theory of plasma jets is developed. Comparison between theory and experiment is made. Good agreement between theory and experiment is found.

  4. Basic Studies on High Pressure Air Plasmas

    DTIC Science & Technology

    2006-08-30

    33, 2268 (2000). [3] Non- Equilibrium Air Plasmas at Atmospheric Pressure, K.H. Becker, U. Kogelschatz, K.H. Schoenbach, and R.J. Barker, eds., IOP...10). Note that LIFBASE assumes local thermodynamic equilibrium . 120 100 oExperimentalm Siuation 80 60 20- 0 -J ~ LkXi 3060 3070 3080 3090 3100...Dual laser interferometer for plasma density measurements on large tokamaks >>, Rev. Sci. Instrum. 49 p.919 (1978) [5] C.W. Gowers, C. Lamb, « A

  5. Eradication of Bacterial Biofilms Using Atmospheric Pressure Non-Thermal Plasmas

    NASA Astrophysics Data System (ADS)

    Alkawareek, Mahmoud; Gilmore, Brendan; Gorman, Sean; Algwari, Qais; Graham, William; O'Connell, Deborah

    2011-10-01

    Bacterial biofilms are ubiquitous in natural and clinical settings and form a major health risk. Biofilms are recognised to be the predominant mode of bacterial growth, and are an immunological challenge compared to planktonic bacteria of the same species. Eradication of biofilms with atmospheric pressure plasma jets is investigated. Cold non-equilibrium plasmas, operated at ambient atmospheric pressure and temperature, are efficient sources for controlled energy transport through highly reactive neutrals (e.g. ROS, RNS), charged particles (ions and electrons), UV radiation, and electro-magnetic fields. A focused panel of clinically significant biofilms, including Pseudomonas aeruginosa, Escherichia coli, Staphylococcus aureus, and Bacillus cereus, are exposed to various plasma jet configurations operated in helium and oxygen mixtures. Viability of surviving cells was determined using both standard plate counting method and XTT viability assay. These are correlated with measurements and simulations of relevant reactive plasma species.

  6. Modeling of plasma jet production from rail and coaxial guns for imploding plasma liner formation*

    NASA Astrophysics Data System (ADS)

    Mason, R. J.; Faehl, R. J.; Kirikpatrick, R. C.; Witherspoon, D.; Cassibry, J.

    2010-11-01

    We study the generation of plasma jets for forming imploding plasma liners using an enhanced version of the ePLAS implicit/hybrid model.^1 Typically, the jets are partially ionized D or Ar gases, in initial 3-10 cm long slugs at 10^16-10^18 electron/cm^3, accelerated for microseconds along 15-30 cm rail or coaxial guns with a 1 cm inter-electrode gap and driven by magnetic fields of a few Tesla. We re-examine the B-field penetration mechanisms that can be active in such wall-connected plasmas,^2 including erosion and EMHD influences, which can subsequently impact plasma liner formation and implosion. For the background and emitted plasma components we discuss optimized PIC and fluid modeling techniques, and the use of implicit fields and hybridized electrons to speed simulation. The plasmas are relatively cold (˜3 eV), so results with fixed atomic Z are compared to those from a simple analytic EOS, and allowing radiative heat loss from the plasma. The use of PIC ions is explored to extract large mean-free-path kinetic effects. 1. R. J. Mason and C. Cranfill, IEEE Trans. Plasma Sci. PS-14, 45 (1986) 2. R. Mason, et al., Phys. Fluids B, 5, 1115 (1993). [4pt] *Research supported in part by USDOE Grant DE-SC0004207.

  7. [The Characteristic Research of ·OH Induced by Water on an Argon Plasma Jet].

    PubMed

    Liu, Kun; Liao, Hua; Zheng, Pei-chao; Wang, Chen-ying; Liu, Hong-di; Danil, Dobrynin

    2015-07-01

    ·OH plays a crucial role in many fields, having aroused wide public concern in the world. Atmospheric Pressure Plasma Jet, which can be achieved by portable device due to working without the vacuum environment, has the advantages of high concentration of reactive species, high electron temperature and low gas temperature. It has become an important research topic in the field of gas discharge with a strong prospect. Especially, how to induce plasma jet to produce ·OH has become a new hotpot in the field of low-temperature plasma. It has been reported that mass ·OH can be induced successfully when water vapor is added to the working gas, but it will be unstable when the concentrate of water reaches a certain degree. Thus, a device of argon plasma jet with a Ring-to-Ring Electrode Configuration has been designed to interact with water in the surrounding air to generate ·OH under atmospheric pressure. In order to increase the production of ·OH, ultrasonic atomizing device is introduced to promote water concentration around the plasma plume. The generating rule of OH(A2J) induced by water has been extensively studied under different voltages and flow rate. ·OH output induced by the plasma has been tested by emission spectrometry, and at the meanwhile, Ar atomic spectral lines at 810.41 and 811.48 nm are also recorded in order to calculate the electron temperature in argon plasma plume. The results show that the water surrounding the plasma plume can be induced to produce ·OH, and OH(A2 ∑+) output increases with the electrode voltage rising from 20 to 28 kV. When the flow rate increases from 100 to 200 L x h(-1), the OH(A2∑+) output increases, but from 200 to 600 L x h(-1), it decreases. The production rules of OH(A2∑+) is the same as that of electron temperature. Therefore, the presumption is proved that ·OH output mainly affected by electron temperature.

  8. Coherent Structures in a Supersonic Jet Excited by Plasma Actuators

    NASA Astrophysics Data System (ADS)

    Gaitonde, Datta; Samimy, Mo

    2010-11-01

    Simulations are used in conjunction with experimental measurements to understand the coherent structures generated by excitation of a Mach 1.3 jet by eight localized arc filament plasma actuators uniformly distributed just upstream of the nozzle exit. Several modes are excited, including the axisymmetric (m=0), helical (m=1-3), and mixed modes (m=±1, ±2) modes. The Strouhal number for all cases is fixed at 0.3, which corresponds to the most amplified frequency. The simulations reproduce the distinct coherent structures measured in the experiment for each azimuthal mode. Detailed analysis of instantaneous, time- and phase-averaged quantities highlights a complex coherent structure generation, evolution and dissipation process. A key feature observed is the initiation of hairpin-like structures with tips/heads in the outer region of the jet shear layer and legs extending forward and slightly inclined in the direction of the jet axis, where the velocity is higher. The subsequent interactions of these structures yield different composite structures in the downstream region. For example, for m=0, adjacent hairpin structures merge to yield axisymmetric rings, with the legs connecting successive structures in the form of ribs in the braid region; and with m=1 and 2 mode excitation, distinct helical and double-helical structures are observed, respectively, with the hairpins forming substructures in the coils.

  9. Solitary and freak waves in superthermal plasma with ion jet

    NASA Astrophysics Data System (ADS)

    Abdelsalam, U. M.; Abdelsalam

    2013-06-01

    The nonlinear solitary and freak waves in a plasma composed of positive and negative ions, superthermal electrons, ion beam, and stationary dust particles have been investigated. The reductive perturbation method is used to obtain the Korteweg-de Vries (KdV) equation describing the system. The latter admits solitary wave solution, while the dynamics of the modulationally unstable wavepackets described by the KdV equation gives rise to the formation of freak/rogue excitation described by the nonlinear Schrödinger equation. In order to show that the characteristics of solitary and freak waves are influenced by plasma parameters, relevant numerical analysis of appropriate nonlinear solutions are presented. The results from this work predict nonlinear excitations that may associate with ion jet and superthermal electrons in Herbig-Haro objects.

  10. Influence of the Laminar Plasma Torch Construction on the Jet Characteristics

    NASA Astrophysics Data System (ADS)

    Cao, Xiuquan; Yu, Deping; Xiang, Yong; Yao, Jin; Miao, Jianguo

    2016-07-01

    Based on two typical laminar plasma torches (LPT), i.e. a multi-electrode plasma torch (MEPT) with segmented anode structure and a two-electrode plasma torch (TEPT) with conventional structure, this paper studied the influence of the LPTs construction on the jet characteristics. Experiments were designed to measure their arc voltage, jet length, thermal efficiency and specific enthalpy using a home-made data acquisition system. With them, the jet characteristics of the two different LPTs were compared in detail. Results show that different plasma torch construction leads to distinctively different characteristics of the generated plasma jet. Based on the different jet characteristics, a plasma torch with appropriate construction could be used to meet the different application requirements. supported by National Natural Science Foundation of China (No. 51405315) and the Laboratory of Precision Manufacturing Technology, CAEP (No. KF15002)

  11. Very low pressure plasma sprayed yttria-stabilized zirconia coating using a low-energy plasma gun

    NASA Astrophysics Data System (ADS)

    Zhu, Lin; Zhang, Nannan; Bolot, Rodolphe; Planche, Marie-Pierre; Liao, Hanlin; Coddet, Christian

    2011-12-01

    In the present study, a more economical low-energy plasma source was used to perform a very low pressure plasma-spray (VLPPS) process. The plasma-jet properties were analyzed by means of optical emission spectroscopy (OES). Moreover, yttria-stabilized zirconia coating (YSZ) was elaborated by a F100 low-power plasma gun under working pressure of 1 mbar, and the substrate specimens were partially shadowed by a baffle-plate during plasma spraying for obtaining different coating microstructures. Based on the SEM observation, a column-like grain coating was deposited by pure vapor deposition at the shadowed region, whereas, in the unshadowed region, the coating exhibited a binary microstructure which was formed by a mixed deposition of melted particles and evaporated particles. The mechanical properties of the coating were also well under investigation.

  12. HP-9825A calculator programs for plotting orbiter RCS jet dynamic pressure contours

    NASA Technical Reports Server (NTRS)

    Wilson, S. W.

    1977-01-01

    Computer programs which generate displays of the dynamic pressure fields generated by orbiter RCS thruster firings are described. The programs can be used to generate dynamic contours for an isolated RCS jet and to superimpose the plume contours for specific jets or jet clusters on front and side views of the orbiter profile.

  13. Extending helium partial pressure measurement technology to JET DTE2 and ITER

    NASA Astrophysics Data System (ADS)

    Klepper, C. C.; Biewer, T. M.; Kruezi, U.; Vartanian, S.; Douai, D.; Hillis, D. L.; Marcus, C.

    2016-11-01

    The detection limit for helium (He) partial pressure monitoring via the Penning discharge optical emission diagnostic, mainly used for tokamak divertor effluent gas analysis, is shown here to be possible for He concentrations down to 0.1% in predominantly deuterium effluents. This result from a dedicated laboratory study means that the technique can now be extended to intrinsically (non-injected) He produced as fusion reaction ash in deuterium-tritium experiments. The paper also examines threshold ionization mass spectroscopy as a potential backup to the optical technique, but finds that further development is needed to attain with plasma pulse-relevant response times. Both these studies are presented in the context of continuing development of plasma pulse-resolving, residual gas analysis for the upcoming JET deuterium-tritium campaign (DTE2) and for ITER.

  14. Extending Helium Partial Pressure Measurement Technology to JET DTE2 and ITER

    SciTech Connect

    Klepper, C Christopher; Biewer, Theodore M; Douai, D.; Hillis, Donald Lee; Marcus, Chris; Kruezi, Uron

    2016-01-01

    The detection limit for helium (He) partial pressure monitoring via the Penning discharge optical emission diagnostic, mainly used for tokamak divertor effluent gas analysis, is shown here to be possible for He concentrations down to 0.1% in predominantly deuterium effluents. This result from a dedicated laboratory study means that the technique can now be extended to intrinsically (non-injected) He produced as fusion reaction ash in deuterium-tritium experiments. The paper also examines threshold ionization mass spectroscopy as a potential backup to the optical technique, but finds that further development is needed to attain with plasma pulse-relevant response times. Both these studies are presented in the context of continuing development of plasma pulse-resolving, residual gas analysis for the upcoming JET deuterium-tritium campaign (DTE-2) and for ITER.

  15. Functionalization of polymers using an atmospheric plasma jet in a fluidized bed reactor and the impact on SLM-processes

    SciTech Connect

    Sachs, M. Schmitt, A. Schmidt, J. Peukert, W. Wirth, K-E

    2014-05-15

    In order to improve thermoplastics (e.g. Polyamide, Polypropylene and Polyethylene) for Selective Laser Beam Melting (SLM) processes a new approach to functionalize temperature sensitive polymer powders in a large scale is investigated. This is achieved by combining an atmospheric pressure plasma jet and a fluidized bed reactor. Using pressurized air as the plasma gas, radicals like OH* are created. The functionalization leads to an increase of the hydrophilicity of the treated polymer powder without changing the bulk properties. Using the polymers in a SLM process to build single layers of melted material leads to an improvement of the melted layers.

  16. Simulation of rarefied low pressure RF plasma flow around the sample

    NASA Astrophysics Data System (ADS)

    Zheltukhin, V. S.; Shemakhin, A. Yu

    2017-01-01

    The paper describes a mathematical model of the flow of radio frequency plasma at low pressure. The hybrid mathematical model includes the Boltzmann equation for the neutral component of the RF plasma, the continuity and the thermal equations for the charged component. Initial and boundary conditions for the corresponding equations are described. The electron temperature in the calculations is 1-4 eV, atoms temperature in the plasma clot is (3-4) • 103 K, in the plasma jet is (3.2-10) • 102 K, the degree of ionization is 10-7-10-5, electron density is 1015-1019 m-3. For calculations plasma parameters is developed soft package on C++ program language, that uses the OpenFOAM library package. Simulations for the vacuum chamber in the presence of a sample and the free jet flow were carried out.

  17. Cold plasma brush generated at atmospheric pressure

    SciTech Connect

    Duan Yixiang; Huang, C.; Yu, Q. S.

    2007-01-15

    A cold plasma brush is generated at atmospheric pressure with low power consumption in the level of several watts (as low as 4 W) up to tens of watts (up to 45 W). The plasma can be ignited and sustained in both continuous and pulsed modes with different plasma gases such as argon or helium, but argon was selected as a primary gas for use in this work. The brush-shaped plasma is formed and extended outside of the discharge chamber with typical dimension of 10-15 mm in width and less than 1.0 mm in thickness, which are adjustable by changing the discharge chamber design and operating conditions. The brush-shaped plasma provides some unique features and distinct nonequilibrium plasma characteristics. Temperature measurements using a thermocouple thermometer showed that the gas phase temperatures of the plasma brush are close to room temperature (as low as 42 deg. C) when running with a relatively high gas flow rate of about 3500 ml/min. For an argon plasma brush, the operating voltage from less than 500 V to about 2500 V was tested, with an argon gas flow rate varied from less than 1000 to 3500 ml/min. The cold plasma brush can most efficiently use the discharge power as well as the plasma gas for material and surface treatment. The very low power consumption of such an atmospheric argon plasma brush provides many unique advantages in practical applications including battery-powered operation and use in large-scale applications. Several polymer film samples were tested for surface treatment with the newly developed device, and successful changes of the wettability property from hydrophobic to hydrophilic were achieved within a few seconds.

  18. Fatal Penetrating Injuries Sustained by High-pressure Water Jet Unit.

    PubMed

    Radojevic, Nemanja; Radnic, Bojana; Curovic, Ivana

    2015-11-01

    The high-pressure water jet unit is a generator of frequent burst of water jets. The water jet reaches very high speeds and is able to cause wounds similar to those of high-velocity projectiles. In the presented case, unusual fatal injuries sustained by water jet are presented. Operating with the unit, an untrained worker accidentally activated a high-pressure water jet unit, and the extremely high pressure of water liberated the jet unit from his hand and whirled it around him. A jet stream of water ran across his body and caused fatal penetrating injuries in the femoral region. The edges of the wound were mainly sharp with contusion rings on the skin beyond the edges. Exploring the inside of the canals during the autopsy, the left femoral artery and vein were found to be completely transected. The resemblance to a firearm entry wound and the severity of the internal injury make it a noteworthy entity.

  19. Atmospheric-pressure plasma activation and surface characterization on polyethylene membrane separator

    NASA Astrophysics Data System (ADS)

    Tseng, Yu-Chien; Li, Hsiao-Ling; Huang, Chun

    2017-01-01

    The surface hydrophilic activation of a polyethylene membrane separator was achieved using an atmospheric-pressure plasma jet. The surface of the atmospheric-pressure-plasma-treated membrane separator was found to be highly hydrophilic realized by adjusting the plasma power input. The variations in membrane separator chemical structure were confirmed by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Chemical analysis showed newly formed carbonyl-containing groups and high surface concentrations of oxygen-containing species on the atmospheric-pressure-plasma-treated polymeric separator surface. It also showed that surface hydrophilicity primarily increased from the polar component after atmospheric-pressure plasma treatment. The surface and pore structures of the polyethylene membrane separator were examined by scanning electron microscopy, revealing a slight alteration in the pore structure. As a result of the incorporation of polar functionalities by atmospheric-pressure plasma activation, the electrolyte uptake and electrochemical impedance of the atmospheric-pressure-plasma-treated membrane separator improved. The investigational results show that the separator surface can be controlled by atmospheric-pressure plasma surface treatment to tailor the hydrophilicity and enhance the electrochemical performance of lithium ion batteries.

  20. Optimum Injection Pressure of a Cavitating Jet for Introducing Compressive Residual Stress into Stainless Steel

    NASA Astrophysics Data System (ADS)

    Soyama, Hitoshi; Nagasaka, Kazuya; Takakuwa, Osamu; Naito, Akima

    Introducing compressive residual stress by a cavitating jet into the sub-surface of components used in nuclear power plants can mitigate stress corrosion cracking in these components. Although applying the jet is an effective method for this purpose, it should be used without causing damage to the surface from water jet droplets arising from high-pressure injection of the water jet. Thus, in introducing compressive residual stress, the injection pressure needs to be optimized. In this paper, in order to determine the optimum injection pressure, the residual stress of stainless steel treated by a jet at various injection pressures was measured using an X-ray diffraction method. The injection pressure of the jet was varied from 5 MPa to 300 MPa, and the diameter of the nozzle throat of the jet was varied from 0.35 mm to 2.0 mm. The variation of residual stress with depth was measured by alternating X-ray diffraction measurements with electropolishing. It was revealed that a cavitating jet at an injection pressure of 10 MPa with a nozzle diameter of 2.0 mm can introduce higher compressive residual stress to deeper into stainless steel compared with a jet at 300 MPa with a nozzle diameter of 0.35 mm when the downstream pressure of the nozzle was constant.

  1. MTF Driven by Plasma Liner Dynamically Formed by the Merging of Plasma Jets: An Overview

    NASA Technical Reports Server (NTRS)

    Thio, Y. C. Francis; Eskridge, Richard; Martin, Adam; Smith, James; Lee, Michael; Rodgers, Stephen L. (Technical Monitor)

    2001-01-01

    One approach for standoff delivery of the momentum flux for compressing the target in MTF consists of using a spherical array of plasma jets to form a spherical plasma shell imploding towards the center of a magnetized plasma, a compact toroid (Figure 1). A 3-year experiment (PLX-1) to explore the physics of forming a 2-D plasma liner (shell) by merging plasma jets is described. An overview showing how this 3-year project (PLX-1) fits into the program plan at the national and international level for realizing MTF for energy and propulsion is discussed. Assuming that there will be a parallel program in demonstrating and establishing the underlying physics principles of MTF using whatever liner is appropriate (e.g. a solid liner) with a goal of demonstrating breakeven by 2010, the current research effort at NASA MSFC attempts to complement such a program by addressing the issues of practical embodiment of MTF for propulsion. Successful conclusion of PLX-1 will be followed by a Physics Feasibility Experiment (PLX-2) for the Plasma Liner Driven MTF.

  2. Predictive transport simulations of real-time profile control in JET advanced tokamak plasmas

    NASA Astrophysics Data System (ADS)

    Tala, T.; Laborde, L.; Mazon, D.; Moreau, D.; Corrigan, G.; Crisanti, F.; Garbet, X.; Heading, D.; Joffrin, E.; Litaudon, X.; Parail, V.; Salmi, A.; EFDA-JET workprogramme, contributors to the

    2005-09-01

    Predictive, time-dependent transport simulations with a semi-empirical plasma model have been used in closed-loop simulations to control the q-profile and the strength and location of the internal transport barrier (ITB). Five transport equations (Te, Ti, q, ne, vΦ) are solved, and the power levels of lower hybrid current drive, NBI and ICRH are calculated in a feedback loop determined by the feedback controller matrix. The real-time control (RTC) technique and algorithms used in the transport simulations are identical to those implemented and used in JET experiments (Laborde L. et al 2005 Plasma Phys. Control. Fusion 47 155 and Moreau D. et al 2003 Nucl. Fusion 43 870). The closed-loop simulations with RTC demonstrate that varieties of q-profiles and pressure profiles in the ITB can be achieved and controlled simultaneously. The simulations also showed that with the same RTC technique as used in JET experiments, it is possible to sustain the q-profiles and pressure profiles close to their set-point profiles for longer than the current diffusion time. In addition, the importance of being able to handle the multiple time scales to control the location and strength of the ITB is pointed out. Several future improvements and perspectives of the RTC scheme are presented.

  3. Reactive species in non-equilibrium atmospheric-pressure plasmas: Generation, transport, and biological effects

    NASA Astrophysics Data System (ADS)

    Lu, X.; Naidis, G. V.; Laroussi, M.; Reuter, S.; Graves, D. B.; Ostrikov, K.

    2016-05-01

    Non-equilibrium atmospheric-pressure plasmas have recently become a topical area of research owing to their diverse applications in health care and medicine, environmental remediation and pollution control, materials processing, electrochemistry, nanotechnology and other fields. This review focuses on the reactive electrons and ionic, atomic, molecular, and radical species that are produced in these plasmas and then transported from the point of generation to the point of interaction with the material, medium, living cells or tissues being processed. The most important mechanisms of generation and transport of the key species in the plasmas of atmospheric-pressure plasma jets and other non-equilibrium atmospheric-pressure plasmas are introduced and examined from the viewpoint of their applications in plasma hygiene and medicine and other relevant fields. Sophisticated high-precision, time-resolved plasma diagnostics approaches and techniques are presented and their applications to monitor the reactive species and plasma dynamics in the plasma jets and other discharges, both in the gas phase and during the plasma interaction with liquid media, are critically reviewed. The large amount of experimental data is supported by the theoretical models of reactive species generation and transport in the plasmas, surrounding gaseous environments, and plasma interaction with liquid media. These models are presented and their limitations are discussed. Special attention is paid to biological effects of the plasma-generated reactive oxygen and nitrogen (and some other) species in basic biological processes such as cell metabolism, proliferation, survival, etc. as well as plasma applications in bacterial inactivation, wound healing, cancer treatment and some others. Challenges and opportunities for theoretical and experimental research are discussed and the authors' vision for the emerging convergence trends across several disciplines and application domains is presented to

  4. Semi-analytical model of plasma-jet-driven magneto-inertial fusion

    NASA Astrophysics Data System (ADS)

    Langendorf, Samuel; Hsu, Scott

    2016-10-01

    Plasma-jet-driven magneto-inertial fusion (PJMIF) is an MIF concept in which a spherically imploding plasma liner is formed from the convergence of a large number of discrete supersonic plasma jets, and the assembled liner is employed to compress a magnetized fuel target. We formulate a 1D spherical-geometry MIF model and apply it to PJMIF. The model incorporates compressible hydrodynamics, liner ionization, radiation, D-T fusion burn, heat conduction losses, magnetic pressure, magnetic flux losses via the Nernst effect, and charged-particle energy deposition. We study the effects of different transport outcomes (e.g., optically thin vs. optically thick radiation transport, classical vs. Bohm-like thermal diffusivity), and scan the liner-target parameter space for configurations with optimal fusion gain at a given total energy. We find that gain-optimal implosion velocity depends significantly on the liner temperature. For liners at approximately room temperature, an implosion speed of roughly 70 km/s is advantageous over faster speeds due to increased dwell time at stagnation. Supported by ARPA-E ALPHA program.

  5. Microwave techniques for electron density measurements in low pressure RF plasmas

    NASA Astrophysics Data System (ADS)

    Zheltukhin, Viktor; Gafarov, Ildar; Shemakhin, Alexander

    2016-09-01

    Results of the experimental studying of RF plasma jet at low pressure in the range of 10 - 300 Pa is presented. The electron density distribution both in inductive and in capacitive coupled RF discharges was measured at 1.76 MHz and 13.56 MHz consequently. We used three independent microwave diagnostic techniques such as free space (the ``two-frequency'' and ``on the cut-off signal'') and a resonator. It is found that the electron density in the RF plasma jets is by 1-2 orders of magnitude greater than in the decaying plasma jet, and by 1-2 orders of magnitude less than in the RF plasma torch. Thus the RF plasma jet is similar to the additional discharge between the electrodes or the coil and the vacuum chamber walls. As a consequence, the formation of the positive charge sheath near the specimen placed in plasma stream is observed. It is found that the maximum of ionization degree as well as more uniform electron density distribution across the stream is observed in the range of the gas flow rate Gg = 0 . 06 - 0 . 12 g/s and the discharge power Pd = 0 . 5 - 2 . 5 kW. The work was funded by RFBR, according to the research projects No. 16-31-60081 mol_a_dk.

  6. MULTIPLE PLASMA EJECTIONS AND INTERMITTENT NATURE OF MAGNETIC RECONNECTION IN SOLAR CHROMOSPHERIC ANEMONE JETS

    SciTech Connect

    Singh, K. A. P.; Nishida, K.; Shibata, K.; Isobe, H.; Nishizuka, N. E-mail: nishida@kwasan.kyoto-u.ac.jp E-mail: isobe@kwasan.kyoto-u.ac.jp

    2012-11-01

    The recent discovery of chromospheric anemone jets with the Solar Optical Telescope (SOT) on board Hinode has shown an indirect evidence of magnetic reconnection in the solar chromosphere. However, the basic nature of magnetic reconnection in chromosphere is still unclear. We studied nine chromospheric anemone jets from SOT/Hinode using Ca II H filtergrams, and we found multiple bright, plasma ejections along the jets. In most cases, the major intensity enhancements (larger than 30% relative to the background intensity) of the loop correspond to the timing of the plasma ejections. The typical lifetime and size of the plasma ejecta are about 20-60 s and 0.3-1.5 Mm, respectively. The height-time plot of jet shows many sub-structures (or individual jets) and the typical lifetime of the individual jet is about one to five minutes. Before the onset of the jet activity, a loop appears in Ca II H and gradually increases in size, and after few minutes several jets are launched from the loop. Once the jet activity starts and several individual jets are launched, the loop starts shrinking with a speed of {approx}4 km s{sup -1}. In some events, a downward moving blob with a speed of {approx}35 km s{sup -1} was observed, associated with the upward moving plasma along one of the legs of the loop hosting the jets. The upward moving plasma gradually developed into jets. Multiple plasma ejections in chromospheric anemone jet show the strongly time-dependent as well as intermittent nature of magnetic reconnection in the solar chromosphere.

  7. A model for straight and helical solar jets. II. Parametric study of the plasma beta

    NASA Astrophysics Data System (ADS)

    Pariat, E.; Dalmasse, K.; DeVore, C. R.; Antiochos, S. K.; Karpen, J. T.

    2016-11-01

    Context. Jets are dynamic, impulsive, well-collimated plasma events that develop at many different scales and in different layers of the solar atmosphere. Aims: Jets are believed to be induced by magnetic reconnection, a process central to many astrophysical phenomena. Within the solar atmosphere, jet-like events develop in many different environments, e.g., in the vicinity of active regions, as well as in coronal holes, and at various scales, from small photospheric spicules to large coronal jets. In all these events, signatures of helical structure and/or twisting/rotating motions are regularly observed. We aim to establish that a single model can generally reproduce the observed properties of these jet-like events. Methods: Using our state-of-the-art numerical solver ARMS, we present a parametric study of a numerical tridimensional magnetohydrodynamic (MHD) model of solar jet-like events. Within the MHD paradigm, we study the impact of varying the atmospheric plasma β on the generation and properties of solar-like jets. Results: The parametric study validates our model of jets for plasma β ranging from 10-3 to 1, typical of the different layers and magnetic environments of the solar atmosphere. Our model of jets can robustly explain the generation of helical solar jet-like events at various β ≤ 1. We introduces the new result that the plasma β modifies the morphology of the helical jet, explaining the different observed shapes of jets at different scales and in different layers of the solar atmosphere. Conclusions: Our results enable us to understand the energisation, triggering, and driving processes of jet-like events. Our model enables us to make predictions of the impulsiveness and energetics of jets as determined by the surrounding environment, as well as the morphological properties of the resulting jets.

  8. Experiments With Radiatively Cooled Supersonic Plasma Jets Generated in Conical Wire Array Z-Pinches

    NASA Astrophysics Data System (ADS)

    Lebedev, S. V.; Ampleford, D. J.; Bland, S. N.; Chittenden, J. P.; Ciardi, A.; Naz, N.; Haines, M. G.; Frank, A.; Blackman, E.; Gardiner, T.

    2002-12-01

    We present results of astrophysically relevant experiments where highly supersonic plasma jets are generated via conically convergent plasma flows in a conical wire array Z-pinch. Stagnation of plasma flow on the axis of symmetry forms a standing conical shock effectively collimating the flow in the axial direction. This scenario is essentially similar to that discussed by Canto and collaborators [1] as a purely hydrodynamic mechanism for jet formation in astrophysical systems. Experiments using different materials (Al, Fe and W) show that a hypersonic (M ~ 20), well-collimated jet is generated when the radiative cooling rate of the plasma is significant.

  9. Magnetic Probe to Study Plasma Jets for Magneto-Inertial Fusion

    SciTech Connect

    Martens, Daniel; Hsu, Scott C.

    2012-08-16

    A probe has been constructed to measure the magnetic field of a plasma jet generated by a pulsed plasma rail-gun. The probe consists of two sets of three orthogonally-oriented commercial chip inductors to measure the three-dimensional magnetic field vector at two separate positions in order to give information about the magnetic field evolution within the jet. The strength and evolution of the magnetic field is one of many factors important in evaluating the use of supersonic plasma jets for forming imploding spherical plasma liners as a standoff driver for magneto-inertial fusion.

  10. LHCD experiments in high performance plasmas in JET

    NASA Astrophysics Data System (ADS)

    Ekedahl, A.; Baranov, Y.; Dobbing, J. A.; Fischer, B.; Goniche, M.; Gormezano, C.; Romero, J. A.; Schild, P.; Söldner, F. X.; Challis, C. D.; Sips, A. C. C.; Tubbing, B.

    1997-04-01

    Lower Hybrid Current Drive (LHCD) has been used for current profile shaping in the shear optimisation experiments in 1996/97 in JET. PLH≲3MW has been applied in the initial current ramp-up in order to control the internal inductance. An internal transport barrier with improved central electron confinement has been produced in this phase with LHCD alone. This has resulted in a peaking of the electron temperature profile and Te0 above 10keV at ne0⩽1.5×1019 m-3. The profile of the LH driven current, as determined by hard X-ray mesurements, is peaked at approximately mid-radius in these conditions. Good coupling of the LH waves has been obtained by the use of a near gas feed. This method reduces the risk of plasma-launcher interaction, since the launcher can be positioned in the shadow of the poloidal limiters. A reflection coefficient of 5% has been maintained at a plasma-launcher distance of 8 cm and PLH=5 MW has been coupled to divertor plasmas in L-mode with this method.

  11. DEVELOPMENT OF WATER JET PLASMA MIRROR FOR STAGING OF LASER PLASMA ACCELERATORS

    SciTech Connect

    Panasenko, Dmitriy; Gonsalves, Anthony J.; Leemans, Wim; Nakamura, Kei; Shu, Anthony; Toth, Csaba

    2009-05-04

    Staging Laser Plasma Accelerators (LPAs) is necessary in order to reach beam energies of 100 GeV and above. This requires incoupling of additional laser beams into accelerating stages. In order to maintain the high average accelerating gradient of a staged LPA, it is imperative to minimize the distance that is needed for laser incoupling. A plasma mirror is proposed as the final coupling optic reducing the coupling distance from tens of meters, using a conventional optic, to as small as a few cm. Both a planar water jet and a nitrocellulose foil are used as reflecting surfacesand characterized. A maximum reflectivity of 70percent was obtained using both surfaces.

  12. Jet Effects on Base and Afterbody Pressures of a Cylindrical Afterbody at Transonic Speeds

    NASA Technical Reports Server (NTRS)

    Cubbage, James M , Jr

    1956-01-01

    An investigation of the effects of jet nozzle geometry, size of base annulus, and base bleed upon the base and afterbody pressures of a cylindrical afterbody at transonic speeds has been conducted. Sonic and supersonic conical nozzles with jet-to-base diameter ratios from 0.25 to 0.85 were investigated with a cold jet at jet total-pressure ratios up to approximately 8.0 through a Mach number range from 0.6 to 1.25. Base pressure coefficients of about -0.55 were measured for the sonic nozzles at a Mach number of 1 or greater. The jet-to-base diameter ratio had a substantial effect on the base pressure obtained on the cylindrical afterbody of this investigation. Base bleed was beneficial in increasing the base pressure under certain conditions but had little or no effect at certain other conditions.

  13. Influence of Plasma Jet Temperature Profiles in Arc Discharge Methods of Carbon Nanotubes Synthesis

    PubMed Central

    Raniszewski, Grzegorz; Wiak, Slawomir; Pietrzak, Lukasz; Szymanski, Lukasz; Kolacinski, Zbigniew

    2017-01-01

    One of the most common methods of carbon nanotubes (CNTs) synthesis is application of an electric-arc plasma. However, the final product in the form of cathode deposit is composed of carbon nanotubes and a variety of carbon impurities. An assay of carbon nanotubes produced in arc discharge systems available on the market shows that commercial cathode deposits contain about 10% CNTs. Given that the quality of the final product depends on carbon–plasma jet parameters, it is possible to increase the yield of the synthesis by plasma jet control. Most of the carbon nanotubes are multiwall carbon nanotubes (MWCNTs). It was observed that the addition of catalysts significantly changes the plasma composition, effective ionization potential, the arc channel conductance, and in effect temperature of the arc and carbon elements flux. This paper focuses on the influence of metal components on plasma-jet forming containing carbon nanotubes cathode deposit. The plasma jet temperature control system is presented. PMID:28336884

  14. Sterilization of Staphylococcus Aureus by an Atmospheric Non-Thermal Plasma Jet

    NASA Astrophysics Data System (ADS)

    Liu, Xiaohu; Hong, Feng; Guo, Ying; Zhang, Jing; Shi, Jianjun

    2013-05-01

    An atmospheric non-thermal plasma jet was developed for sterilizing the Staphylococcus aureus (S. aureus). The plasma jet was generated by dielectric barrier discharge (DBD), which was characterized by electrical and optical diagnostics. The survival curves of the bacteria showed that the plasma jet could effectively inactivate 106 cells of S. aureus within 120 seconds and the sterilizing efficiency depended critically on the discharge parameter of the applied voltage. It was further confirmed by scanning electron microscopy (SEM) that the cell morphology was seriously damaged by the plasma treatment. The plasma sterilization mechanism of S. aureus was attributed to the active species of OH, N2+ and O, which were generated abundantly in the plasma jet and characterized by OES. Our findings suggest a convenient and low-cost way for sterilization and inactivation of bacteria.

  15. Design of experimental setup for supercritical CO2 jet under high ambient pressure conditions.

    PubMed

    Shi, Huaizhong; Li, Gensheng; He, Zhenguo; Wang, Haizhu; Zhang, Shikun

    2016-12-01

    With the commercial extraction of hydrocarbons in shale and tight reservoirs, efficient methods are needed to accelerate developing process. Supercritical CO2 (SC-CO2) jet has been considered as a potential way due to its unique fluid properties. In this article, a new setup is designed for laboratory experiment to research the SC-CO2 jet's characteristics in different jet temperatures, pressures, standoff distances, ambient pressures, etc. The setup is composed of five modules, including SC-CO2 generation system, pure SC-CO2 jet system, abrasive SC-CO2 jet system, CO2 recovery system, and data acquisition system. Now, a series of rock perforating (or case cutting) experiments have been successfully conducted using the setup about pure and abrasive SC-CO2 jet, and the results have proven the great perforating efficiency of SC-CO2 jet and the applications of this setup.

  16. Effects of real viscosity on plasma liner formation and implosion from supersonic plasma jets

    NASA Astrophysics Data System (ADS)

    Schillo, Kevin; Cassibry, Jason; Hsu, Scott; PLX-Alpha Team

    2015-11-01

    The PLX- α project endeavors to study plasma liner formation and implosion by merging of a spherical array of plasma jets as a candidate standoff driver for magneto-inertial fusion (MIF). Smoothed particle hydrodynamics (SPH) is being used to model the liner formation and implosion processes. SPH is a meshless Lagrangian method to simulate fluid flows by dividing a fluid into a set of particles and using a summation interpolant function to calculate the properties and gradients for each of these particles. The SPH code was used to simulate test cases in which the number of plasma guns and initial conditions for the plasma were varied. Linear stabilizations were observed, but the possibility exists that this stabilization was due to the implementation of artificial viscosity in the code. A real viscosity model was added to our SPHC model using the Braginskii ion viscosity. Preliminary results for test cases that incorporate real viscosity are presented.

  17. On the evolution of jet energy and opening angle in strongly coupled plasma

    NASA Astrophysics Data System (ADS)

    Chesler, Paul M.; Rajagopal, Krishna

    2016-05-01

    We calculate how the energy and the opening angle of jets in {N} = 4 SYM theory evolve as they propagate through the strongly coupled plasma of that theory. We define the rate of energy loss dE jet /dx and the jet opening angle in a straightforward fashion directly in the gauge theory before calculating both holographically, in the dual gravitational description. In this way, we rederive the previously known result for dE jet /dx without the need to introduce a finite slab of plasma. We obtain a striking relationship between the initial opening angle of the jet, which is to say the opening angle that it would have had if it had found itself in vacuum instead of in plasma, and the thermalization distance of the jet. Via this relationship, we show that {N} = 4 SYM jets with any initial energy that have the same initial opening angle and the same trajectory through the plasma experience the same fractional energy loss. We also provide an expansion that describes how the opening angle of the {N} = 4 SYM jets increases slowly as they lose energy, over the fraction of their lifetime when their fractional energy loss is not yet large. We close by looking ahead toward potential qualitative lessons from our results for QCD jets produced in heavy collisions and propagating through quark-gluon plasma.

  18. On the evolution of jet energy and opening angle in strongly coupled plasma

    SciTech Connect

    Chesler, Paul M.; Rajagopal, Krishna

    2016-05-17

    We calculate how the energy and the opening angle of jets in N = 4SYM theory evolve as they propagate through the strongly coupled plasma of that theory. We define the rate of energy loss dEjet/dx and the jet opening angle in a straightforward fashion directly in the gauge theory before calculating both holographically, in the dual gravitational description. In this way, we rederive the previously known result for dEjet/dx without the need to introduce a finite slab of plasma. We obtain a striking relationship between the initial opening angle of the jet, which is to say the opening angle that it would have had if it had found itself in vacuum instead of in plasma, and the thermalization distance of the jet. Via this relationship, we show that N = 4SYM jets with any initial energy that have the same initial opening angle and the same trajectory through the plasma experience the same fractional energy loss. We also provide an expansion that describes how the opening angle of the N = 4SYM jets increases slowly as they lose energy, over the fraction of their lifetime when their fractional energy loss is not yet large. In conclusion, we close by looking ahead toward potential qualitative lessons from our results for QCD jets produced in heavy collisions and propagating through quark-gluon plasma.

  19. Investigating the Mutagenicity of a Cold Argon-Plasma Jet in an HET-MN Model

    PubMed Central

    Bender, Claudia; Benkhai, Hicham; Sckell, Axel; Below, Harald; Stope, Matthias B.; Kramer, Axel

    2016-01-01

    Objective So-called cold physical plasmas for biomedical applications generate reactive oxygen and nitrogen species and the latter can trigger DNA damage at high concentrations. Therefore, the mutagenic risks of a certified atmospheric pressure argon plasma jet (kINPen MED) and its predecessor model (kINPen 09) were assessed. Methods Inner egg membranes of fertilized chicken eggs received a single treatment with either the kINPen 09 (1.5, 2.0, or 2.5 min) or the kINPen MED (3, 4, 5, or 10 min). After three days of incubation, blood smears (panoptic May-Grünwald-Giemsa stain) were performed, and 1000 erythrocytes per egg were evaluated for the presence of polychromatic and normochromic nuclear staining as well as nuclear aberrations and binucleated cells (hen’s egg test for micronuclei induction, HET-MN). At the same time, the embryo mortality was documented. For each experiment, positive controls (cyclophosphamide and methotrexate) and negative controls (NaCl-solution, argon gas) were included. Additionally, the antioxidant potential of the blood plasma was assessed by ascorbic acid oxidation assay after treatment. Results For both plasma sources, there was no evidence of genotoxicity, although at the longest plasma exposure time of 10 min the mortality of the embryos exceeded 40%. The antioxidant potential in the egg’s blood plasma was not significantly reduced immediately (p = 0.32) or 1 h (p = 0.19) post exposure to cold plasma. Conclusion The longest plasma treatment time with the kINPen MED was 5–10 fold above the recommended limit for treatment of chronic wounds in clinics. We did not find mutagenic effects for any plasma treatment time using the either kINPen 09 or kINPen MED. The data provided with the current study seem to confirm the lack of a genotoxic potential suggesting that a veterinary or clinical application of these argon plasma jets does not pose mutagenic risks. PMID:27584003

  20. Generating Long Scale-Length Plasma Jets Embedded in a Uniform, Multi-Tesla Magnetic-Field

    NASA Astrophysics Data System (ADS)

    Manuel, Mario; Kuranz, Carolyn; Rasmus, Alex; Klein, Sallee; Fein, Jeff; Belancourt, Patrick; Drake, R. P.; Pollock, Brad; Hazi, Andrew; Park, Jaebum; Williams, Jackson; Chen, Hui

    2013-10-01

    Collimated plasma jets emerge in many classes of astrophysical objects and are of great interest to explore in the laboratory. In many cases, these astrophysical jets exist within a background magnetic field where the magnetic pressure approaches the plasma pressure. Recent experiments performed at the Jupiter Laser Facility utilized a custom-designed solenoid to generate the multi-tesla fields necessary to achieve proper magnetization of the plasma. Time-gated interferometry, Schlieren imaging, and proton radiography were used to characterize jet evolution and collimation under varying degrees of magnetization. Experimental results will be presented and discussed. This work is funded by the NNSA-DS and SC-OFES Joint Program in High-Energy-Density Laboratory Plasmas, grant number DE-NA0001840, by the National Laser User Facility Program, grant number DE-NA0000850, by the Predictive Sciences Academic Alliances Program in NNSA-ASC, grant number DEFC52-08NA28616, and by NASA through Einstein Postdoctoral Fellowship grant number PF3-140111 awarded by the Chandra X-ray Center, which is operated by the Smithsonian Astrophysical Observatory for NASA under contract NAS8-03060.

  1. Modeling the Compression of Merged Compact Toroids by Multiple Plasma Jets

    NASA Technical Reports Server (NTRS)

    Thio, Y. C. Francis; Knapp, Charles E.; Kirkpatrick, Ron; Rodgers, Stephen L. (Technical Monitor)

    2000-01-01

    A fusion propulsion scheme has been proposed that makes use of the merging of a spherical distribution of plasma jets to dynamically form a gaseous liner. The gaseous liner is used to implode a magnetized target to produce the fusion reaction in a standoff manner. In this paper, the merging of the plasma jets to form the gaseous liner is investigated numerically. The Los Alamos SPHINX code, based on the smoothed particle hydrodynamics method is used to model the interaction of the jets. 2-D and 3-D simulations have been performed to study the characteristics of the resulting flow when these jets collide. The results show that the jets merge to form a plasma liner that converge radially which may be used to compress the central plasma to fusion conditions. Details of the computational model and the SPH numerical methods will be presented together with the numerical results.

  2. Laboratory Study of the Shaping and Evolution of Magnetized Episodic Plasma Jets

    NASA Astrophysics Data System (ADS)

    Higginson, Drew

    2015-11-01

    The expansion of hot, dense plasma (100 eV, 1018 cm-3) into vacuum occupied by a strong magnetic field (β =Pkinetic /Pmag ~ 1) along the expansion axis is a seemingly elementary physics problem, yet it is one that has scarcely been investigated. As well as being a fundamental problem in plasma physics, understanding such a situation is important to provide an explanation of large-scale jets observed in the formation of young stellar objects (YSO). Additionally, the ability to manipulate such a situation (e.g. to optimize x-ray emission) may be essential to the feasibility of recently proposed inertial confinement fusion (ICF) schemes with an imposed magnetic field. To investigate these situations, a CF2 foil is irradiated with the ELFIE laser (1013 W/cm2, 0.6 ns) in an external axial magnetic field of 20 T. As the plasma expands radially it is restricted by magnetic pressure that creates a cavity with a shock at the expansion edge. This shock redirects flow back on axis and creates a strong, stationary, conical shock that collimates the flow into a jet traveling over 1000 km/s and extending many centimeters. The effect of episodic heating (e.g. from variable mass ejection in a YSO, or pulse shaping in ICF) was investigated by irradiating the target with a precursor laser (1012 W/cm2, 0.6 ns) at 9 to 19 ns prior to the main pulse. The addition of this relatively small addition of energy (<20% of the main pulse energy) changed the dynamics of the expansion dramatically by increasing the strength of the conical shock, reducing the forward expansion of the cavity and dramatically increasing emission. We also present MHD simulations that reproduce the experimental observables and help to understand dynamics of jet and cavity formation. Prepared by LLNL under Contract DE-AC52-07NA27344. Presently at Lawrence Livermore National Laboratory.

  3. Analysis of conductive target influence in plasma jet experiments through helium metastable and electric field measurements

    NASA Astrophysics Data System (ADS)

    Darny, T.; Pouvesle, J.-M.; Puech, V.; Douat, C.; Dozias, S.; Robert, Eric

    2017-04-01

    The use of cold atmospheric pressure plasma jets for in vivo treatments implies most of the time plasma interaction with conductive targets. The effect of conductive target contact on the discharge behavior is studied here for a grounded metallic target and compared to the free jet configuration. In this work, realized with a plasma gun, we measured helium metastable HeM (23S1) concentration (by laser absorption spectroscopy) and electric field (EF) longitudinal and radial components (by electro-optic probe). Both diagnostics were temporally and spatially resolved. Mechanisms after ionization front impact on the target surface have been identified. The remnant conductive ionized channel behind the ionization front electrically transiently connects the inner high voltage electrode to the target. Due to impedance mismatching between the ionized channel and the target, a secondary ionization front is initiated and rapidly propagates from the target surface to the inner electrode through this ionized channel. This leads to a greatly enhanced HeM production inside the plasma plume and the capillary. Forward and reverse dynamics occur with further multi reflections of more or less damped ionization fronts between the inner electrode and the target as long as the ionized channel is persisting. This phenomenon is very sensitive to parameters such as target distance and ionized channel conductivity affecting electrical coupling between these two and evidenced using positive or negative voltage polarity and nitrogen admixture. In typical operating conditions for the plasma gun used in this work, it has been found that after the secondary ionization front propagation, when the ionized channel is conductive enough, a glow like discharge occurs with strong conduction current. HeM production and all species excitation, especially reactive ones, are then driven by high voltage pulse evolution. The control of forward and reverse dynamics, impacting on the production of the glow

  4. The effect of applied electric field on pulsed radio frequency and pulsed direct current plasma jet array

    SciTech Connect

    Hu, J. T.; Liu, X. Y.; Liu, J. H.; Xiong, Z. L.; Liu, D. W.; Lu, X. P.; Iza, F.; Kong, M. G.

    2012-06-15

    Here we compare the plasma plume propagation characteristics of a 3-channel pulsed RF plasma jet array and those of the same device operated by a pulsed dc source. For the pulsed-RF jet array, numerous long life time ions and metastables accumulated in the plasma channel make the plasma plume respond quickly to applied electric field. Its structure similar as 'plasma bullet' is an anode glow indeed. For the pulsed dc plasma jet array, the strong electric field in the vicinity of the tube is the reason for the growing plasma bullet in the launching period. The repulsive forces between the growing plasma bullets result in the divergence of the pulsed dc plasma jet array. Finally, the comparison of 309 nm and 777 nm emissions between these two jet arrays suggests the high chemical activity of pulsed RF plasma jet array.

  5. Model polymer etching and surface modification by a time modulated RF plasma jet: role of atomic oxygen and water vapor

    NASA Astrophysics Data System (ADS)

    Luan, P.; Knoll, A. J.; Wang, H.; Kondeti, V. S. S. K.; Bruggeman, P. J.; Oehrlein, G. S.

    2017-01-01

    The surface interaction of a well-characterized time modulated radio frequency (RF) plasma jet with polystyrene, poly(methyl methacrylate) and poly(vinyl alcohol) as model polymers is investigated. The RF plasma jet shows fast polymer etching but mild chemical modification with a characteristic carbonate ester and NO formation on the etched surface. By varying the plasma treatment conditions including feed gas composition, environment gaseous composition, and treatment distance, we find that short lived species, especially atomic O for Ar/1% O2 and 1% air plasma and OH for Ar/1% H2O plasma, play an essential role for polymer etching. For O2 containing plasma, we find that atomic O initiates polymer etching and the etching depth mirrors the measured decay of O atoms in the gas phase as the nozzle-surface distance increases. The etching reaction probability of an O atom ranging from 10-4 to 10-3 is consistent with low pressure plasma research. We also find that adding O2 and H2O simultaneously into Ar feed gas quenches polymer etching compared to adding them separately which suggests the reduction of O and OH density in Ar/O2/H2O plasma.

  6. Flow control in low pressure turbine blades using plasma actuators

    NASA Astrophysics Data System (ADS)

    Ramakumar, Karthik

    2005-11-01

    An experimental study of plasma flow control actuators for flow separation control in low pressure turbine (LPT) blades is presented. The actuator arrangement consists of two copper strips separated by a dielectric medium with an input voltage of approximately 5kV and a frequency input varying from 3-5 kHz, creating a region of plasma used for boundary layer flow control. The effect of varying waveform on control efficacy is investigated using sine, square and saw tooth waveforms. The impact of duty cycle and forcing frequency on both displacement and momentum thickness are also examined. Boundary layer measurements are carried out using PIV while measurements of the wake downstream are performed using a 7-hole probe for Reynolds number ranging from 30,000 to 50,000. Separation is fully controlled in most configurations and boundary layer parameters reveal that the actuator entrains the free-stream flow at the actuator location and creates a region of high turbulence, essentially behaving similar to an active boundary layer trip. A small region of reversed flow near the surface indicates the presence of cross-stream vortical structures. The use of plasma synthetic jet actuators flow LPT flow control is also discussed.

  7. Effect of the atmospheric pressure nonequilibrium plasmas on the conformational changes of plasmid DNA

    NASA Astrophysics Data System (ADS)

    Yan, Xu; Zou, Fei; Lu, Xin Pei; He, Guangyuan; Shi, Meng Jun; Xiong, Qing; Gao, Xuan; Xiong, Zilan; Li, Yin; Ma, Feng Yun; Yu, Men; Wang, Chang Dong; Wang, Yuesheng; Yang, Guangxiao

    2009-08-01

    The cold atmospheric pressure plasma, which has been widely used for biomedical applications, may potentially affect the conformation of DNA. In this letter, an atmospheric pressure plasma plume is used to investigate its effects on the conformational changes of DNA of plasmid pAHC25. It is found that the plasma plume could cause plasmid DNA topology alteration, resulting in the percentage of the supercoiled plasmid DNA form decreased while that of the open circular and linearized form of plasmid DNA increased as detected by agrose gel electrophoresis. On the other hand, further investigation by using polymerase chain reaction method shows that the atmospheric pressure plasma jet treatments under proper conditions does not affect the genes of the plasmid DNA, which may have potential application in increasing the transformation frequency by genetic engineering.

  8. Effect of the atmospheric pressure nonequilibrium plasmas on the conformational changes of plasmid DNA

    SciTech Connect

    Yan Xu; He Guangyuan; Shi Mengjun; Gao Xuan; Li Yin; Ma Fengyun; Yu Men; Wang Changdong; Wang Yuesheng; Yang Guangxiao; Zou Fei; Lu Xinpei; Xiong Qing; Xiong Zilan

    2009-08-24

    The cold atmospheric pressure plasma, which has been widely used for biomedical applications, may potentially affect the conformation of DNA. In this letter, an atmospheric pressure plasma plume is used to investigate its effects on the conformational changes of DNA of plasmid pAHC25. It is found that the plasma plume could cause plasmid DNA topology alteration, resulting in the percentage of the supercoiled plasmid DNA form decreased while that of the open circular and linearized form of plasmid DNA increased as detected by agrose gel electrophoresis. On the other hand, further investigation by using polymerase chain reaction method shows that the atmospheric pressure plasma jet treatments under proper conditions does not affect the genes of the plasmid DNA, which may have potential application in increasing the transformation frequency by genetic engineering.

  9. In-situ monitoring of etching of bovine serum albumin using low-temperature atmospheric plasma jet

    NASA Astrophysics Data System (ADS)

    Kousal, J.; Shelemin, A.; Kylián, O.; Slavínská, D.; Biederman, H.

    2017-01-01

    Bio-decontamination of surfaces by means of atmospheric pressure plasma is nowadays extensively studied as it represents promising alternative to commonly used sterilization/decontamination techniques. The non-equilibrium atmospheric pressure plasmas were already reported to be highly effective in removal of a wide range of biological residual from surfaces. Nevertheless the kinetics of removal of biological contamination from surfaces is still not well understood as the majority of performed studies were based on ex-situ evaluation of etching rates, which did not allow investigating details of plasma action on biomolecules. This study therefore presents a real-time, in-situ ellipsometric characterization of removal of bovine serum albumin (BSA) from surfaces by low-temperature atmospheric plasma jet operated in argon. Non-linear and at shorter distances between treated samples and nozzle of the plasma jet also non-monotonic dependence of the removal rate on the treatment duration was observed. According to additional measurements focused on the determination of chemical changes of treated BSA as well as temperature measurements, the observed behavior is most likely connected with two opposing effects: the formation of a thin layer on the top of BSA deposit enriched in inorganic compounds, whose presence causes a gradual decrease of removal efficiency, and slight heating of BSA that facilitates its degradation and volatilization induced by chemically active radicals produced by the plasma.

  10. Comparison of H-mode plasmas in JET-ILW and JET-C with and without nitrogen seeding

    NASA Astrophysics Data System (ADS)

    Jaervinen, A. E.; Giroud, C.; Groth, M.; Belo, P.; Brezinsek, S.; Beurskens, M.; Corrigan, G.; Devaux, S.; Drewelow, P.; Harting, D.; Huber, A.; Jachmich, S.; Lawson, K.; Lipschultz, B.; Maddison, G.; Maggi, C.; Marchetto, C.; Marsen, S.; Matthews, G. F.; Meigs, A. G.; Moulton, D.; Sieglin, B.; Stamp, M. F.; Wiesen, S.; Contributors, JET

    2016-04-01

    In high confinement mode, highly shaped plasmas with edge localized modes in JET, and for heating power of 15-17 MW, the edge fluid code EDGE2D-EIRENE predicts transition to detachment assisted by nitrogen at the low field side (LFS) target when more than 50% of the power crossing the separatrix between ELMs is radiated in the divertor chamber, i.e. ~4 MW. This is observed both in the ITER-like wall (JET-ILW) and in the carbon wall (JET-C) configurations and is consistent with experimental observations within their uncertainty. In these conditions, peak heat fluxes below 1 MW m-2 are measured at the LFS target and predicted for both wall configurations. When the JET-C configuration is replaced with the JET-ILW, a factor of two reduction in the divertor radiated power and 25-50% increase in the peak and total power deposited to the LFS divertor plate is predicted by EDGE2D-EIRENE for unseeded plasmas similar to experimental observations. At the detachment threshold, EDGE2D-EIRENE shows that nitrogen radiates more than 80% of the total divertor radiation in JET-ILW with beryllium contributing less than a few %. With JET-C, nitrogen radiates more than 70% with carbon providing less than 20% of the total radiation. Therefore, the lower intrinsic divertor radiation with JET-ILW is compensated by stronger nitrogen radiation contribution in simulations leading to detachment at similar total divertor radiation fractions. 20-100% higher deuterium molecular fraction in the divertor recycling fluxes is predicted with light JET-C materials when compared to heavy tungsten. EDGE2D-EIRENE simulations indicate that the stronger molecular contribution can reduce the divertor peak power deposition in high recycling conditions by 10-20% due to enhanced power dissipation by molecular interaction.

  11. The effect of lower hybrid waves on JET plasma rotation

    NASA Astrophysics Data System (ADS)

    Nave, M. F. F.; Kirov, K.; Bernardo, J.; Brix, M.; Ferreira, J.; Giroud, C.; Hawkes, N.; Hellsten, T.; Jonsson, T.; Mailloux, J.; Ongena, J.; Parra, F.; Contributors, JET

    2017-03-01

    This paper reports on observations of rotation in JET plasmas with lower hybrid current drive. Lower hybrid (LH) has a clear impact on rotation. The changes in core rotation can be either in the co- or counter-current directions. Experimental features that could determine the direction of rotation were investigated. Changes from co- to counter-rotation as the q-profile evolves from above unity to below unity suggests that magnetic shear could be important. However, LH can drive either co- or counter-rotation in discharges with similar magnetic shear and at the same plasma current. It is not clear if a slightly lower density is significant. A power scan at fixed density, shows a lower hybrid power threshold around 3 MW. For smaller LH powers, counter rotation increases with power, while for larger powers a trend towards co-rotation is found. The estimated counter-torque from the LH waves, would not explain the observed angular frequencies, neither would it explain the observation of co-rotation.

  12. Degeneration of amyloid-ß fibrils caused by exposure to low-temperature atmospheric-pressure plasma in aqueous solution

    NASA Astrophysics Data System (ADS)

    Takai, Eisuke; Ohashi, Gai; Yoshida, Tomonori; Margareta Sörgjerd, Karin; Zako, Tamotsu; Maeda, Mizuo; Kitano, Katsuhisa; Shiraki, Kentaro

    2014-01-01

    Low-temperature atmospheric-pressure plasma was applied to degenerate amyloid-ß (Aß) fibrils, which are a major component of neuritic plaque associated with Alzheimer's disease (AD). We showed that an Aß fibril exposed to a low-frequency (LF) plasma jet in aqueous solution retained its morphology, molecular weight, and cytotoxicity, but, intriguingly, decreased in protease resistance and ß-sheet content. These results suggested that an LF plasma jet could be utilized for the treatment of AD to eliminate neuritic plaque by accelerating the proteolysis of Aß fibrils.

  13. Electro-physical property of plasma jet generated by burning chemicals as antenna

    NASA Astrophysics Data System (ADS)

    Zhong-Cai, Yuan; Jia-Ming, Shi; Xiao-Po, Wu; Zong-Shen, Chen; Zong-Shen

    2013-02-01

    The application of pulsed power to transient radiofrequency/microwave radiation for warhead/projectile payloads is currently a significant area of research. In this paper, the far-field radiative property of a plasma antenna is analyzed. Then, a plasma jet is generated by burning chemicals, in which the electron concentration and collision frequency are diagnosed, and the electric conductance is calculated. Finally, the feasibility to apply the plasma jet as antenna is investigated by analyzing the radiative pattern. The dependency of pattern on plasma electron density, collision frequency, and plasma wake radius is calculated and analyzed.

  14. Streamer properties in a repetitively pulsed plasma jet from 1 to 100 kHz

    NASA Astrophysics Data System (ADS)

    Sands, Brian; Ganguly, Biswa; Scofield, James

    2015-09-01

    We investigate the properties of guided streamers in a nanosecond repetitively pulsed dielectric barrier plasma jet at repetition rates up to 100 kHz. In this regime, remnant ionization and neutral metastable concentrations are significant in the channel through which the streamer propagates. Both helium and a Penning mixture of helium and argon are investigated as feed gases for a plasma jet in a controlled pressure chamber with a flowing nitrogen background. The applied voltage pulse was set at 8 kV, with a risetime of 15 ns and falltime of 8.5 μs. Streamer dynamics were monitored using spatiotemporally-resolved emission spectroscopy with a PMT filtered at 706.5 nm He (33S - 23P) and 587.6 nm He (33D - 23P) to track the streamer head. Temporally-resolved ICCD imaging was also used to characterize discharge development. Tunable diode laser absorption spectroscopy was used to measure He (23S1) and Ar (3P2) metastable densities in the streamer chann