Measurement of fracture properties of concrete at high strain rates

PubMed Central

Cendón, D. A.; Sánchez-Gálvez, V.; Gálvez, F.

2017-01-01

An analysis of the spalling technique of concrete bars using the modified Hopkinson bar was carried out. A new experimental configuration is proposed adding some variations to previous works. An increased length for concrete specimens was chosen and finite-element analysis was used for designing a conic projectile to obtain a suitable triangular impulse wave. The aim of this initial work is to establish an experimental framework which allows a simple and direct analysis of concrete subjected to high strain rates. The efforts and configuration of these primary tests, as well as the selected geometry and dimensions for the different elements, have been focused to achieve a simple way of identifying the fracture position and so the tensile strength of tested specimens. This dynamic tensile strength can be easily compared with previous values published in literature giving an idea of the accuracy of the method and technique proposed and the possibility to extend it in a near future to obtain other mechanical properties such as the fracture energy. The tests were instrumented with strain gauges, accelerometers and high-speed camera in order to validate the results by different ways. Results of the dynamic tensile strength of the tested concrete are presented. This article is part of the themed issue ‘Experimental testing and modelling of brittle materials at high strain rates’. PMID:27956510

Transport relaxation processes in supercritical fluids

NASA Astrophysics Data System (ADS)

Jonas, J.

The technique for solubility measurements of solids in compressed supercritical fluids using NMR and theoretical analysis of experimental data on collision induced scattering were examined. Initial tests for a determination of solid solubilities in supercritical fluids without mixing were previously described and these preparations have continued. Super critical carbon dioxide dissolving naphthalene, for which solubility data is already available (M. McHugh, M.E. Paulaitis, J. Chem. Eng. Data, Vol. 25 (4), 1980) is being studied. This initial testing of the NMR technique for measuring solubilities in a well characterized system should prove very valuable for our later determinations with the proposed mixing probe. Systematic experimental studies of collision induced spectra in several supercritical fluids using both Raman and Rayleigh scattering are continued. The experimental work on SF6 and CH4 was finished and the experimental data testing of the various theoretical models for collision induced scattering is being analyzed.

Hypothesis testing on the fractal structure of behavioral sequences: the Bayesian assessment of scaling methodology.

PubMed

Moscoso del Prado Martín, Fermín

2013-12-01

I introduce the Bayesian assessment of scaling (BAS), a simple but powerful Bayesian hypothesis contrast methodology that can be used to test hypotheses on the scaling regime exhibited by a sequence of behavioral data. Rather than comparing parametric models, as typically done in previous approaches, the BAS offers a direct, nonparametric way to test whether a time series exhibits fractal scaling. The BAS provides a simpler and faster test than do previous methods, and the code for making the required computations is provided. The method also enables testing of finely specified hypotheses on the scaling indices, something that was not possible with the previously available methods. I then present 4 simulation studies showing that the BAS methodology outperforms the other methods used in the psychological literature. I conclude with a discussion of methodological issues on fractal analyses in experimental psychology. PsycINFO Database Record (c) 2014 APA, all rights reserved.

The strong Bell inequalities: A proposed experimental test

NASA Technical Reports Server (NTRS)

Fry, Edward S.

1994-01-01

All previous experimental tests of Bell inequalities have required additional assumptions. The strong Bell inequalities (i.e. those requiring no additional assumptions) have never been tested. An experiment has been designed that can, for the first time, provide a definitive test of the strong Bell inequalities. Not only will the detector efficiency loophole be closed; but the locality condition will also be rigorously enforced. The experiment involves producing two Hg-199 atoms by a resonant Raman dissociation of a mercury dimer ((199)Hg2) that is in an electronic and nuclear spin singlet state. Bell inequalities can be tested by measuring angular momentum correlations between the spin one-half nuclei of the two Hg-199 atoms. The method used to make these latter measurements will be described.

Does Extrinsic Goal Framing Enhance Extrinsic Goal-Oriented Individuals' Learning and Performance? An Experimental Test of the Match Perspective versus Self-Determination Theory

ERIC Educational Resources Information Center

Vansteenkiste, Maarten; Timmermans, Tinneke; Lens, Willy; Soenens, Bart; Van den Broeck, Anja

2008-01-01

Previous work within self-determination theory has shown that experimentally framing a learning activity in terms of extrinsic rather than intrinsic goals results in poorer conceptual learning and performance, presumably because extrinsic goal framing detracts attention from the learning activity and is less directly satisfying of basic…

An Experimental Study on the Effects of Stereotype Awareness on the Subjective Grading of Undergraduate College Essays

ERIC Educational Resources Information Center

Mikesell-Redding, Danielle

2012-01-01

Racial equality is promoted on nearly every academic campus across America; however, research has shown that educators express racial bias in various ways. The purpose of this experimental research was to determine the extent of racial bias among White, undergraduate professors, an area lacking previous research. The study tested whether a…

Experimental Design for a Macrofoam Swab Study Relating the Recovery Efficiency and False Negative Rate to Low Concentrations of Two Bacillus anthracis Surrogates on Four Surface Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Piepel, Gregory F.; Hutchison, Janine R.

2014-04-16

This report describes the experimental design for a laboratory study to quantify the recovery efficiencies and false negative rates of a validated, macrofoam swab sampling method for low concentrations of Bacillus anthracis Sterne (BAS) and Bacillus atrophaeus (BG) spores on four surface materials (stainless steel, glass, vinyl tile, plastic light cover panel). Two analytical methods (plating/counting and polymerase chain reaction) will be used. Only one previous study has investigated false negative as a function of affecting test factors. The surrogates BAS and BG have not been tested together in the same study previously. Hence, this study will provide for completingmore » gaps in the available information on the performance of macrofoam swab sampling at low concentrations.« less

Experimental Design for a Macrofoam-Swab Study Relating the Recovery Efficiency and False Negative Rate to Low Concentrations of Two Bacillus anthracis Surrogates on Four Surface Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Piepel, Gregory F.; Hutchison, Janine R.

This report describes the experimental design for a laboratory study to quantify the recovery efficiencies and false negative rates of a validated, macrofoam-swab sampling method for low concentrations of Bacillus anthracis Sterne (BAS) and Bacillus atrophaeus (BG) spores on four surface materials (stainless steel, glass, vinyl tile, plastic light cover panel). Two analytical methods (culture and polymerase chain reaction) will be used. Only one previous study has investigated how the false negative rate depends on test factors. The surrogates BAS and BG have not been tested together in the same study previously. Hence, this study will provide for completing gapsmore » in the available information on the performance of macrofoam-swab sampling at low concentrations.« less

Predicting multi-wall structural response to hypervelocity impact using the hull code

NASA Technical Reports Server (NTRS)

Schonberg, William P.

1993-01-01

Previously, multi-wall structures have been analyzed extensively, primarily through experiment, as a means of increasing the meteoroid/space debris impact protection of spacecraft. As structural configurations become more varied, the number of tests required to characterize their response increases dramatically. As an alternative to experimental testing, numerical modeling of high-speed impact phenomena is often being used to predict the response of a variety of structural systems under different impact loading conditions. The results of comparing experimental tests to Hull Hydrodynamic Computer Code predictions are reported. Also, the results of a numerical parametric study of multi-wall structural response to hypervelocity cylindrical projectile impact are presented.

Airflow Resistance of Loose-Fill Mineral Fiber Insulations in Retrofit Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schumacher, C. J.; Fox, M. J.; Lstiburek, J.

2015-02-01

This report expands on Building America Report 1109 by applying the experimental apparatus and test method to dense-pack retrofit applications using mineral fiber insulation materials. Three fiber glass insulation materials and one stone wool insulation material were tested, and the results compared to the cellulose results from the previous study.

Nonlinear analysis of concrete beams strengthened by date palm fibers

NASA Astrophysics Data System (ADS)

Bouzouaid, Samia; Kriker, Abdelouahed

2017-02-01

The behaviour of concrete beams strengthened with date palm fibers was studied by Nonlinear Finite Element Analysis using ANSYS software. Five beams that were experimentally tested in a previous research were considered. The results obtained from the ANSYS finite element analysis are compared with the experimental data for the five beams with different amounts of fibres, ranging from 0.2% to 0.5% by a step equal to 0.1% and with a fibre length of 0.04 m. The results obtained by FEA showed good agreement with those obtained by the experimental program. This research demonstrates the ability of FEA in predicting the behaviour of beams strengthened with Date Palm fibers. It will help researchers in studying beams with different configurations without the need to go through the lengthy experimental testing programs.

Quasi experimental designs in pharmacist intervention research.

PubMed

Krass, Ines

2016-06-01

Background In the field of pharmacist intervention research it is often difficult to conform to the rigorous requirements of the "true experimental" models, especially the requirement of randomization. When randomization is not feasible, a practice based researcher can choose from a range of "quasi-experimental designs" i.e., non-randomised and at time non controlled. Objective The aim of this article was to provide an overview of quasi-experimental designs, discuss their strengths and weaknesses and to investigate their application in pharmacist intervention research over the previous decade. Results In the literature quasi experimental studies may be classified into five broad categories: quasi-experimental design without control groups; quasi-experimental design that use control groups with no pre-test; quasi-experimental design that use control groups and pre-tests; interrupted time series and stepped wedge designs. Quasi-experimental study design has consistently featured in the evolution of pharmacist intervention research. The most commonly applied of all quasi experimental designs in the practice based research literature are the one group pre-post-test design and the non-equivalent control group design i.e., (untreated control group with dependent pre-tests and post-tests) and have been used to test the impact of pharmacist interventions in general medications management as well as in specific disease states. Conclusion Quasi experimental studies have a role to play as proof of concept, in the pilot phases of interventions when testing different intervention components, especially in complex interventions. They serve to develop an understanding of possible intervention effects: while in isolation they yield weak evidence of clinical efficacy, taken collectively, they help build a body of evidence in support of the value of pharmacist interventions across different practice settings and countries. However, when a traditional RCT is not feasible for logistical and/or ethical reasons researchers should endeavour to use the more robust of the quasi experimental designs.

Experimental Investigation of Compressed Thin-Walled Steel Members

NASA Astrophysics Data System (ADS)

Juhás, Pavol; Juhásová Šenitková, Ingrid

2017-10-01

The paper presents fundamental information about realized experimental-theoretical research to determinate the load-carrying capacities for thin-walled compressed steel members with quasi-homogenous and hybrid cross-sections. The webs of such members are stressed in the elastic-plastic region. This continuous research joins on previous research of the first author of the paper. The aim of this research is to investigate and analyse the elastic-plastic post-critical behaviour of thin web and its interaction with flanges. The experimental program, test members and their geometrical parameters and material properties are evident from table 1 and table 2 as well as from figure 1 and figure 2. The test arrangement and failures of the test members are illustrated on Figures 3, 4 and 5. Some partial results are presented in Table 3 of the paper, too.

Modeling the backscattering and transmission properties of vegetation canopies

NASA Technical Reports Server (NTRS)

Allen, C. T.; Ulaby, F. T.

1984-01-01

Experimental measurements of canopy attenuation at 10.2 GHz (X-band) for canopies of wheat and soybeans, experimental observations of the effect upon the microwave backscattering coefficient (sigma) of free water in a vegetation canopy, and experimental measurements of sigma (10.2 GHz, 50 deg, VV and VH polarization) of 30 agricultural fields over the growing season of each crop are discussed. The measurements of the canopy attenuation through wheat independently determined the attenuation resulting from the wheat heads and that from the stalks. An experiment conducted to simulate the effects of rain or dew on sigma showed that sigma increases by about 3 dB as a result of spraying a vegetation canopy with water. The temporal observations of sigma for the 30 agricultural fields (10 each of wheat, corn, and soybeans) indicated fields of the same crop type exhibits similar temporal patterns. Models previously reported were tested using these multitemporal sigma data, and a new model for each crop type was developed and tested. The new models proved to be superior to the previous ones.

Development of Optimal Stressor Scenarios for New Operational Energy Systems

DTIC Science & Technology

2017-12-01

Analyzing the previous model using a design of experiments (DOE) and regression analysis provides critical information about the associated operational...from experimentation. The resulting system requirements can be used to revisit the design requirements and develop a more robust system. This process...stressor scenarios for acceptance testing. Analyzing the previous model using a design of experiments (DOE) and regression analysis provides critical

Priming International Affairs: How the Media Influence Attitudes toward Foreign Countries.

ERIC Educational Resources Information Center

Willnat, Lars; Graf, Joseph; Brewer, Paul R.

This study broadens the scope of priming research by testing whether media coverage of international affairs shapes the criteria which people use to judge foreign countries. In contrast to previous priming experiments that focused on the effects of television news stories, this study experimentally tests the power of print media to produce priming…

Airflow Resistance of Loose-Fill Mineral Fiber Insulations in Retrofit Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schumacher, C. J.; Fox, M. J.; Lstiburek, J.

2015-02-01

This report expands on Building America Report 1109 by applying the experimental apparatus and test method to dense-pack retrofit applications using mineral fiber insulation materials. Three (3) fiber glass insulation materials and one (1) stone wool insulation material were tested, and the results compared to the cellulose results from the previous study.

Spike-Nosed Bodies and Forward Injected Jets in Supersonic Flow

NASA Technical Reports Server (NTRS)

Gilinsky, M.; Washington, C.; Blankson, I. M.; Shvets, A. I.

2002-01-01

The paper contains new numerical simulation and experimental test results of blunt body drag reduction using thin spikes mounted in front of a body and one- or two-phase jets injected against a supersonic flow. Numerical simulations utilizing the NASA CFL3D code were conducted at the Hampton University Fluid Mechanics and Acoustics Laboratory (FM&AL) and experimental tests were conducted using the facilities of the IM/MSU Aeromechanics and Gas Dynamics Laboratory. Previous results were presented at the 37th AIAA/ASME/SAE/ASEE Joint Propulsion Conference. Those results were based on some experimental and numerical simulation tests for supersonic flow around spike-nosed or shell-nosed bodies, and numerical simulations were conducted only for a single spike-nosed or shell-nosed body at zero attack angle, alpha=0. In this paper, experimental test results of gas, liquid and solid particle jet injection against a supersonic flow are presented. In addition, numerical simulation results for supersonic flow around a multiple spike-nosed body with non-zero attack angles and with a gas and solid particle forward jet injection are included. Aerodynamic coefficients: drag, C(sub D), lift, C(sub L), and longitudinal momentum, M(sub z), obtained by numerical simulation and experimental tests are compared and show good agreement.

Spike-Nosed Bodies and Forward Injected Jets in Supersonic Flow

NASA Technical Reports Server (NTRS)

Gilinsky, M.; Washington, C.; Blankson, I. M.; Shvets, A. I.

2002-01-01

The paper contains new numerical simulation and experimental test results of blunt body drag reduction using thin spikes mounted in front of a body and one- or two-phase jets injected against a supersonic flow. Numerical simulations utilizing the NASA CFL3D code were conducted at the Hampton University Fluid Mechanics and Acoustics Laboratory (FM&AL) and experimental tests were conducted using the facilities of the IM/MSU Aeromechanics and Gas Dynamics Laboratory. Previous results were presented at the 37th AIAA/ASME/SAE/ASEE Joint Propulsion Conference. Those results were based on some experimental and numerical simulation tests for supersonic flow around spike-nosed or shell-nosed bodies, and numerical simulations were conducted only for a single spike-nosed or shell-nosed body at zero attack angle, alpha = 0 degrees. In this paper, experimental test results of gas, liquid and solid particle jet injection against a supersonic flow are presented. In addition, numerical simulation results for supersonic flow around a multiple spike-nosed body with non-zero attack angles and with a gas and solid particle forward jet injection are included. Aerodynamic coefficients: drag, C (sub D), lift, C(sub L), and longitudinal momentum, M(sub z), obtained by numerical simulation and experimental tests are compared and show good agreement.

Analysis of Dynamic Fracture Compliance Based on Poroelastic Theory - Part II: Results of Numerical and Experimental Tests

NASA Astrophysics Data System (ADS)

Wang, Ding; Ding, Pin-bo; Ba, Jing

2018-03-01

In Part I, a dynamic fracture compliance model (DFCM) was derived based on the poroelastic theory. The normal compliance of fractures is frequency-dependent and closely associated with the connectivity of porous media. In this paper, we first compare the DFCM with previous fractured media theories in the literature in a full frequency range. Furthermore, experimental tests are performed on synthetic rock specimens, and the DFCM is compared with the experimental data in the ultrasonic frequency band. Synthetic rock specimens saturated with water have more realistic mineral compositions and pore structures relative to previous works in comparison with natural reservoir rocks. The fracture/pore geometrical and physical parameters can be controlled to replicate approximately those of natural rocks. P- and S-wave anisotropy characteristics with different fracture and pore properties are calculated and numerical results are compared with experimental data. Although the measurement frequency is relatively high, the results of DFCM are appropriate for explaining the experimental data. The characteristic frequency of fluid pressure equilibration calculated based on the specimen parameters is not substantially less than the measurement frequency. In the dynamic fracture model, the wave-induced fluid flow behavior is an important factor for the fracture-wave interaction process, which differs from the models at the high-frequency limits, for instance, Hudson's un-relaxed model.

Experimental Study of under-platform Damper Kinematics in Presence of Blade Dynamics

NASA Astrophysics Data System (ADS)

Botto, D.; Gastaldi, C.; Gola, M. M.; Umer, M.

2018-01-01

Among the different devices used in the aerospace industries under-platform dampers are widely used in turbo engines to mitigate the blade vibration. Nevertheless, the damper behaviour is not easy to simulate and engineers have been working in order to improve the accuracy with which theoretical contact models predict the damper behaviour. Majority of the experimental setups collect experimental data in terms of blade amplitude reduction which do not increase the knowledge about the damper dynamics and therefore the uncertainty on the damper behaviour remains a big issue. In this paper, a novel test rig has been purposely designed to accommodate a single blade and two under-platform dampers to deeply investigate the damper-blade interactions. In this test bench, a contact force measuring system was designed to extensively measure the damper contact forces. Damper kinematics is rebuilt by using the relative displacement measured between damper and blade. This paper describes the concept behind the new approach, shows the details of new test rig and discusses experimental results by comparing with previously measured results on an old experimental setup.

An Experimental Comparison Between Flexible and Rigid Airfoils at Low Reynolds Numbers

NASA Astrophysics Data System (ADS)

Uzodinma, Jaylon; Macphee, David

2017-11-01

This study uses experimental and computational research methods to compare the aerodynamic performance of rigid and flexible airfoils at a low Reynolds number throughout varying angles of attack. This research can be used to improve the design of small wind turbines, micro-aerial vehicles, and any other devices that operate at low Reynolds numbers. Experimental testing was conducted in the University of Alabama's low-speed wind tunnel, and computational testing was conducted using the open-source CFD code OpenFOAM. For experimental testing, polyurethane-based (rigid) airfoils and silicone-based (flexible) airfoils were constructed using acrylic molds for NACA 0012 and NACA 2412 airfoil profiles. Computer models of the previously-specified airfoils were also created for a computational analysis. Both experimental and computational data were analyzed to examine the critical angles of attack, the lift and drag coefficients, and the occurrence of laminar boundary separation for each airfoil. Moreover, the computational simulations were used to examine the resulting flow fields, in order to provide possible explanations for the aerodynamic performances of each airfoil type. EEC 1659710.

Acoustical characteristics of the NASA Langley full scale wind tunnel test section

NASA Technical Reports Server (NTRS)

Abrahamson, A. L.; Kasper, P. K.; Pappa, R. S.

1975-01-01

The full-scale wind tunnel at NASA-Langley Research Center was designed for low-speed aerodynamic testing of aircraft. Sound absorbing treatment has been added to the ceiling and walls of the tunnel test section to create a more anechoic condition for taking acoustical measurements during aerodynamic tests. The results of an experimental investigation of the present acoustical characteristics of the tunnel test section are presented. The experimental program included measurements of ambient nosie levels existing during various tunnel operating conditions, investigation of the sound field produced by an omnidirectional source, and determination of sound field decay rates for impulsive noise excitation. A comparison of the current results with previous measurements shows that the added sound treatment has improved the acoustical condition of the tunnel test section. An analysis of the data indicate that sound reflections from the tunnel ground-board platform could create difficulties in the interpretation of actual test results.

Immersion freezing of supermicron mineral dust particles: freezing results, testing different schemes for describing ice nucleation, and ice nucleation active site densities.

PubMed

Wheeler, M J; Mason, R H; Steunenberg, K; Wagstaff, M; Chou, C; Bertram, A K

2015-05-14

Ice nucleation on mineral dust particles is known to be an important process in the atmosphere. To accurately implement ice nucleation on mineral dust particles in atmospheric simulations, a suitable theory or scheme is desirable to describe laboratory freezing data in atmospheric models. In the following, we investigated ice nucleation by supermicron mineral dust particles [kaolinite and Arizona Test Dust (ATD)] in the immersion mode. The median freezing temperature for ATD was measured to be approximately -30 °C compared with approximately -36 °C for kaolinite. The freezing results were then used to test four different schemes previously used to describe ice nucleation in atmospheric models. In terms of ability to fit the data (quantified by calculating the reduced chi-squared values), the following order was found for ATD (from best to worst): active site, pdf-α, deterministic, single-α. For kaolinite, the following order was found (from best to worst): active site, deterministic, pdf-α, single-α. The variation in the predicted median freezing temperature per decade change in the cooling rate for each of the schemes was also compared with experimental results from other studies. The deterministic model predicts the median freezing temperature to be independent of cooling rate, while experimental results show a weak dependence on cooling rate. The single-α, pdf-α, and active site schemes all agree with the experimental results within roughly a factor of 2. On the basis of our results and previous results where different schemes were tested, the active site scheme is recommended for describing the freezing of ATD and kaolinite particles. We also used our ice nucleation results to determine the ice nucleation active site (INAS) density for the supermicron dust particles tested. Using the data, we show that the INAS densities of supermicron kaolinite and ATD particles studied here are smaller than the INAS densities of submicron kaolinite and ATD particles previously reported in the literature.

Metacognitive and multimedia support of experiments in inquiry learning for science teacher preparation

NASA Astrophysics Data System (ADS)

Bruckermann, Till; Aschermann, Ellen; Bresges, André; Schlüter, Kirsten

2017-04-01

Promoting preservice science teachers' experimentation competency is required to provide a basis for meaningful learning through experiments in schools. However, preservice teachers show difficulties when experimenting. Previous research revealed that cognitive scaffolding promotes experimentation competency by structuring the learning process, while metacognitive and multimedia support enhance reflection. However, these support measures have not yet been tested in combination. Therefore, we decided to use cognitive scaffolding to support students' experimental achievements and supplement it by metacognitive and multimedia scaffolds in the experimental groups. Our research question is to what extent supplementing cognitive support by metacognitive and multimedia scaffolding further promotes experimentation competency. The intervention has been applied in a two-factorial design to a two-month experimental course for 63 biology teacher students in their first bachelor year. Pre-post-test measured experimentation competency in a performance assessment. Preservice teachers worked in groups of four. Therefore, measurement took place at group level (N = 16). Independent observers rated preservice teachers' group performance qualitatively on a theory-based system of categories. Afterwards, experimentation competency levels led to quantitative frequency analysis. The results reveal differing gains in experimentation competency but contrary to our hypotheses. Implications of combining scaffolding measures on promoting experimentation competency are discussed.

Multiple comparison analysis testing in ANOVA.

PubMed

McHugh, Mary L

2011-01-01

The Analysis of Variance (ANOVA) test has long been an important tool for researchers conducting studies on multiple experimental groups and one or more control groups. However, ANOVA cannot provide detailed information on differences among the various study groups, or on complex combinations of study groups. To fully understand group differences in an ANOVA, researchers must conduct tests of the differences between particular pairs of experimental and control groups. Tests conducted on subsets of data tested previously in another analysis are called post hoc tests. A class of post hoc tests that provide this type of detailed information for ANOVA results are called "multiple comparison analysis" tests. The most commonly used multiple comparison analysis statistics include the following tests: Tukey, Newman-Keuls, Scheffee, Bonferroni and Dunnett. These statistical tools each have specific uses, advantages and disadvantages. Some are best used for testing theory while others are useful in generating new theory. Selection of the appropriate post hoc test will provide researchers with the most detailed information while limiting Type 1 errors due to alpha inflation.

Excitation spectra of liquid iron up to superhigh temperatures

NASA Astrophysics Data System (ADS)

Fomin, Yu D.; Ryzhov, V. N.; Tsiok, E. N.; Brazhkin, V. V.

2017-08-01

Investigation of excitation spectra of liquids is one of the hot test topics nowadays. In particular, recent experimental works showed that liquid metals can demonstrate transverse excitations and positive sound dispersion. However, the theoretical description of these experimental observations is still missing. Here we report a molecular dynamics study of excitation spectra of liquid iron. We compare the results with available experimental data to justify the method. After that we perform calculations for high temperatures to find the location of the Frenkel line introduced in our previous works.

Equation of State for RX-08-EL and RX-08-EP

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, E.L.; Walton, J.

1985-05-07

JWL Equations of State (EOS's) have been estimated for RX-08-EL and RX-08-EP. The estimated JWL EOS parameters are listed. Previously, we derived a JWL EOS for RX-08-EN based on DYNA2D hydrodynamic code cylinder computations and comparisons with experimental cylinder test results are shown. The experimental cylinder shot results for RX-08-EL, shot K-473, were compared to the experimental cylinder shot results for RX-08-EN, shot K-463, as a reference. 10 figs., 6 tabs.

Flow induced vibrations in the SSME injector heads

NASA Technical Reports Server (NTRS)

Lepore, Frank A.

1991-01-01

A description is given of the flowfield in the Space Shuttle Main Engine (SSME) powerhead, the mechanisms which control flow-induced vibrations, and previous experimental work. An in-depth description is given of the development phase of the program , which includes the analysis, design, and fabrication of liquid oxygen (LOX) posts models used in the experimental phase, as well as test facilities, equipment, and procedures used. Also covered is the experimental data analysis, which includes overall steady state powerhead flowfield as well as the high frequency response of the LOX posts.

Testing large aspheric surfaces with complementary annular subaperture interferometric method

NASA Astrophysics Data System (ADS)

Hou, Xi; Wu, Fan; Lei, Baiping; Fan, Bin; Chen, Qiang

2008-07-01

Annular subaperture interferometric method has provided an alternative solution to testing rotationally symmetric aspheric surfaces with low cost and flexibility. However, some new challenges, particularly in the motion and algorithm components, appear when applied to large aspheric surfaces with large departure in the practical engineering. Based on our previously reported annular subaperture reconstruction algorithm with Zernike annular polynomials and matrix method, and the experimental results for an approximate 130-mm diameter and f/2 parabolic mirror, an experimental investigation by testing an approximate 302-mm diameter and f/1.7 parabolic mirror with the complementary annular subaperture interferometric method is presented. We have focused on full-aperture reconstruction accuracy, and discuss some error effects and limitations of testing larger aspheric surfaces with the annular subaperture method. Some considerations about testing sector segment with complementary sector subapertures are provided.

Development and fabrication of structural components for a scramjet engine

NASA Technical Reports Server (NTRS)

Buchmann, O. A.

1990-01-01

A program broadly directed toward design and development of long-life (100 hours and 1,000 cycles with a goal of 1,000 hours and 10,000 cycles) hydrogen-cooled structures for application to scramjets is presented. Previous phases of the program resulted in an overall engine design and analytical and experimental characterization of selected candidate materials and concepts. The latter efforts indicated that the basic life goals for the program can be reached with available means. The main objective of this effort was an integrated, experimental evaluation of the results of the previous program phases. The fuel injection strut was selected for this purpose, including fabrication development and fabrication of a full-scale strut. Testing of the completed strut was to be performed in a NASA-Langley wind tunnel. In addition, conceptual designs were formulated for a heat transfer test unit and a flat panel structural test unit. Tooling and fabrication procedures required to fabricate the strut were developed, and fabrication and delivery to NASA of all strut components, including major subassemblies, were completed.

Experimental and numerical investigation into the influence of loading conditions in biomechanical testing of locking plate fracture fixation devices

PubMed Central

MacLeod, A.; Simpson, A. H. R. W.

2018-01-01

Objectives Secondary fracture healing is strongly influenced by the stiffness of the bone-fixator system. Biomechanical tests are extensively used to investigate stiffness and strength of fixation devices. The stiffness values reported in the literature for locked plating, however, vary by three orders of magnitude. The aim of this study was to examine the influence that the method of restraint and load application has on the stiffness produced, the strain distribution within the bone, and the stresses in the implant for locking plate constructs. Methods Synthetic composite bones were used to evaluate experimentally the influence of four different methods of loading and restraining specimens, all used in recent previous studies. Two plate types and three screw arrangements were also evaluated for each loading scenario. Computational models were also developed and validated using the experimental tests. Results The method of loading was found to affect the gap stiffness strongly (by up to six times) but also the magnitude of the plate stress and the location and magnitude of strains at the bone-screw interface. Conclusions This study demonstrates that the method of loading is responsible for much of the difference in reported stiffness values in the literature. It also shows that previous contradictory findings, such as the influence of working length and very large differences in failure loads, can be readily explained by the choice of loading condition. Cite this article: A. MacLeod, A. H. R. W. Simpson, P. Pankaj. Experimental and numerical investigation into the influence of loading conditions in biomechanical testing of locking plate fracture fixation devices. Bone Joint Res 2018;7:111–120. DOI: 10.1302/2046-3758.71.BJR-2017-0074.R2. PMID:29363522

Evaluation of a Low-Noise Formate Spiral-Bevel Gear Set

NASA Technical Reports Server (NTRS)

Lewicki, David g.; Woods, Ron L.; Litvin, Faydor L.; Fuentes, Alfonso

2007-01-01

Studies to evaluate low-noise Formate spiral-bevel gears were performed. Experimental tests were performed on the OH-58D helicopter main-rotor transmission in the NASA Glenn 500-hp Helicopter Transmission Test Stand. Low-noise Formate spiral-bevel gears were compared to the baseline OH-58D spiral-bevel gear design, a high-strength design, and previously tested low-noise designs (including an original low-noise design and an improved-bearing-contact low-noise design). Noise, vibration, and tooth strain tests were performed. The Formate design showed a decrease in noise and vibration compared to the baseline OH-58D design, and was similar to that of the previously tested improved-bearing contact low-noise design. The pinion tooth stresses for the Formate design significantly decreased in comparison to the baseline OH-58D design. Also similar to that of the improved bearing-contact low-noise design, the maximum stresses of the Formate design shifted toward the heel, compared to the center of the face width for the baseline, high-strength, and previously tested low-noise designs.

Transport Test Problems for Hybrid Methods Development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaver, Mark W.; Miller, Erin A.; Wittman, Richard S.

2011-12-28

This report presents 9 test problems to guide testing and development of hybrid calculations for the ADVANTG code at ORNL. These test cases can be used for comparing different types of radiation transport calculations, as well as for guiding the development of variance reduction methods. Cases are drawn primarily from existing or previous calculations with a preference for cases which include experimental data, or otherwise have results with a high level of confidence, are non-sensitive, and represent problem sets of interest to NA-22.

Experimental Analysis of Dynamic Effects of FRP Reinforced Masonry Vaults.

PubMed

Corradi, Marco; Borri, Antonio; Castori, Giulio; Coventry, Kathryn

2015-11-27

An increasing interest in the preservation of historic structures has produced a need for new methods for reinforcing curved masonry structures, such as arches and vaults. These structures are generally very ancient, have geometries and materials which are poorly defined and have been exposed to long-term historical movements and actions. Consequently, they are often in need of repair or reinforcement. This article presents the results of an experimental study carried out in the laboratory and during on-site testing to investigate the behaviour of brick masonry vaults under dynamic loading strengthened with FRPs (Fiber Reinforced Polymers). For the laboratory tests, the brick vaults were built with solid sanded clay bricks and weak mortar and were tested under dynamic loading. The experimental tests were designed to facilitate analysis of the dynamic behaviour of undamaged, damaged and reinforced vaulted structures. On-site tests were carried out on an earthquake-damaged thin brick vault of an 18th century aristocratic residence in the city of L'Aquila, Italy. The provision of FRP reinforcement is shown to re-establish elastic behavior previously compromised by time induced damage in the vaults.

Experimental Analysis of Dynamic Effects of FRP Reinforced Masonry Vaults

PubMed Central

Corradi, Marco; Borri, Antonio; Castori, Giulio; Coventry, Kathryn

2015-01-01

An increasing interest in the preservation of historic structures has produced a need for new methods for reinforcing curved masonry structures, such as arches and vaults. These structures are generally very ancient, have geometries and materials which are poorly defined and have been exposed to long-term historical movements and actions. Consequently, they are often in need of repair or reinforcement. This article presents the results of an experimental study carried out in the laboratory and during on-site testing to investigate the behaviour of brick masonry vaults under dynamic loading strengthened with FRPs (Fiber Reinforced Polymers). For the laboratory tests, the brick vaults were built with solid sanded clay bricks and weak mortar and were tested under dynamic loading. The experimental tests were designed to facilitate analysis of the dynamic behaviour of undamaged, damaged and reinforced vaulted structures. On-site tests were carried out on an earthquake-damaged thin brick vault of an 18th century aristocratic residence in the city of L’Aquila, Italy. The provision of FRP reinforcement is shown to re-establish elastic behavior previously compromised by time induced damage in the vaults. PMID:28793697

Experimental Investigation into the Radar Anomalies on the Surface of Venus

NASA Technical Reports Server (NTRS)

Kohler, E.; Gavin, P.; Chevrier, V.; Johnson, Natasha M.

2012-01-01

Radar mapping of thc surface of Venus shows areas of high reflectivity (low emissivity) in the Venusian highlands at altitudes between 2.5-4.75 kilometers. The origin of the radar anomalies found in the Venusian highlands remains unclear. Most explanations of the potential causes for these radar anomalies come from theoretical work. Previous studies suggest increased surface roughness or materials with higher dielectric constants as well as surface atmospheric interactions. Several possible candidates of high-dielectric materials are tellurium) ferroelectric materials, and lead or bismuth sulfides. While previous studies have been influential in determining possible sources for the Venus anomalies, only a very few hypotheses have been verified via experimentation. This work intends to experimentally constrain the source of the radar anomalies on Venus. This study proposes to investigate four possible materials that could potentially cause the high reflectivities on the surface of Venus and tests their behavior under simulated Venusian conditions.

Investigation of the Thermomechanical Response of Shape Memory Alloy Hybrid Composite Beams

NASA Technical Reports Server (NTRS)

Davis, Brian A.

2005-01-01

Previous work at NASA Langley Research Center (LaRC) involved fabrication and testing of composite beams with embedded, pre-strained shape memory alloy (SMA) ribbons. That study also provided comparison of experimental results with numerical predictions from a research code making use of a new thermoelastic model for shape memory alloy hybrid composite (SMAHC) structures. The previous work showed qualitative validation of the numerical model. However, deficiencies in the experimental-numerical correlation were noted and hypotheses for the discrepancies were given for further investigation. The goal of this work is to refine the experimental measurement and numerical modeling approaches in order to better understand the discrepancies, improve the correlation between prediction and measurement, and provide rigorous quantitative validation of the numerical model. Thermal buckling, post-buckling, and random responses to thermal and inertial (base acceleration) loads are studied. Excellent agreement is achieved between the predicted and measured results, thereby quantitatively validating the numerical tool.

Ignition and Growth Modeling of Detonating LX-04 (85% HMX / 15% VITON) Using New and Previously Obtained Experimental Data

NASA Astrophysics Data System (ADS)

Tarver, Craig

2017-06-01

An Ignition and Growth reactive flow model for detonating LX-04 (85% HMX / 15% Viton) was developed using new and previously obtained experimental data on: cylinder test expansion; wave curvature; failure diameter; and laser interferometric copper and tantalum foil free surface velocities and LiF interface particle velocity histories. A reaction product JWL EOS generated by the CHEETAH code compared favorably with the existing, well normalized LX-04 product JWL when both were used with the Ignition and Growth model. Good agreement with all existing experimental data was obtained. Keywords: LX-04, HMX, detonation, Ignition and Growth PACS:82.33.Vx, 82.40.Fp This work was performed under the auspices of the U. S. Department of Energy by the Lawrence Livermore National Laboratory under Contract No. DE-AC52-07NA27344.

Application of Vacuum Swing Adsorption for Carbon Dioxide and Water Vapor Removal from Manned Spacecraft Atmospheres

NASA Technical Reports Server (NTRS)

Knox, J.; Fulda, P.; Howard, D.; Ritter, J.; Levan, M.

2007-01-01

The design and testing of a vacuum-swing adsorption process to remove metabolic 'water and carbon dioxide gases from NASA's Orion crew exploration vehicle atmosphere is presented. For the Orion spacecraft, the sorbent-based atmosphere revitalization (SBAR) system must remove all metabolic water, a technology approach 1Lhathas not been used in previous spacecraft life support systems. Design and testing of a prototype SBAR in sub-scale and full-scale configurations is discussed. Experimental and analytical investigations of dual-ended and single-ended vacuum desorption are presented. An experimental investigation of thermal linking between adsorbing and desorbing columns is also presented.

The Effects of Stereotypes on the Achievement Gap: Reexamining the Academic Performance of African American High School Students

ERIC Educational Resources Information Center

Kellow, J. Thomas; Jones, Brett D.

2008-01-01

This study investigated whether African American high school freshman students experience stereotype threat when taking a test that is seen as a predictor of their success on a high-stakes test. The authors conceptually replicated a previous study by Kellow and Jones (2005) using a true experimental design, as opposed to a quasi-experimental…

Post-exercise blood flow restriction attenuates hyperemia similarly in males and females.

PubMed

Dankel, Scott J; Mouser, J Grant; Jessee, Matthew B; Mattocks, Kevin T; Buckner, Samuel L; Loenneke, Jeremy P

2017-08-01

Our laboratory recently demonstrated that post-exercise blood flow restriction attenuated muscle hypertrophy only in females, which we hypothesized may be due to alterations in post-exercise blood flow. The aim of this study is to test our previous hypothesis that sex differences in blood flow would exist when employing the same protocol. Twenty-two untrained individuals (12 females; 10 males) performed two exercise sessions, each involving one set of elbow flexion exercise to volitional failure on the right arm. The experimental condition had blood flow restriction applied for a 3 min post-exercise period, whereas the control condition did not. Blood flow was measured using an ultrasound at the brachial artery and was taken 1 and 4 min post-exercise. This corresponded to 1 min post inflation and 1 min post deflation in the experimental condition. There were no differences in the alterations in blood flow between the control and experimental conditions when examined across sex. Increases in blood flow [mean (standard deviation)] were as follows: males 1 min [control 764 (577) %; experimental 113 (108) %], males 4 min [control 346 (313) %; experimental 449 (371) %], females 1 min [control 558 (367) %; experimental 87 (105) %], and females 4 min [control 191 (183) %; experimental 328 (223) %]. It does not appear that the sex-specific attenuation of muscle hypertrophy we observed previously can be attributed to different alterations in post-exercise blood flow. Future studies may wish to replicate our previous training study, or examine alternative mechanisms which may be sex specific.

Automatically generated acceptance test: A software reliability experiment

NASA Technical Reports Server (NTRS)

Protzel, Peter W.

1988-01-01

This study presents results of a software reliability experiment investigating the feasibility of a new error detection method. The method can be used as an acceptance test and is solely based on empirical data about the behavior of internal states of a program. The experimental design uses the existing environment of a multi-version experiment previously conducted at the NASA Langley Research Center, in which the launch interceptor problem is used as a model. This allows the controlled experimental investigation of versions with well-known single and multiple faults, and the availability of an oracle permits the determination of the error detection performance of the test. Fault interaction phenomena are observed that have an amplifying effect on the number of error occurrences. Preliminary results indicate that all faults examined so far are detected by the acceptance test. This shows promise for further investigations, and for the employment of this test method on other applications.

An Automated, Experimenter-Free Method for the Standardised, Operant Cognitive Testing of Rats

PubMed Central

Rivalan, Marion; Munawar, Humaira; Fuchs, Anna; Winter, York

2017-01-01

Animal models of human pathology are essential for biomedical research. However, a recurring issue in the use of animal models is the poor reproducibility of behavioural and physiological findings within and between laboratories. The most critical factor influencing this issue remains the experimenter themselves. One solution is the use of procedures devoid of human intervention. We present a novel approach to experimenter-free testing cognitive abilities in rats, by combining undisturbed group housing with automated, standardized and individual operant testing. This experimenter-free system consisted of an automated-operant system (Bussey-Saksida rat touch screen) connected to a home cage containing group living rats via an automated animal sorter (PhenoSys). The automated animal sorter, which is based on radio-frequency identification (RFID) technology, functioned as a mechanical replacement of the experimenter. Rats learnt to regularly and individually enter the operant chamber and remained there for the duration of the experimental session only. Self-motivated rats acquired the complex touch screen task of trial-unique non-matching to location (TUNL) in half the time reported for animals that were manually placed into the operant chamber. Rat performance was similar between the two groups within our laboratory, and comparable to previously published results obtained elsewhere. This reproducibility, both within and between laboratories, confirms the validity of this approach. In addition, automation reduced daily experimental time by 80%, eliminated animal handling, and reduced equipment cost. This automated, experimenter-free setup is a promising tool of great potential for testing a large variety of functions with full automation in future studies. PMID:28060883

Older Adults' Memory for Verbally Presented Medical Information

ERIC Educational Resources Information Center

Bankoff, Sarah M.; Sandberg, Elisabeth Hollister

2012-01-01

Previous research demonstrates that patients typically have difficulty remembering information presented during healthcare consultations. This study examined how older adults learn and remember verbally presented medical information. Healthy older adults were tested for recall in experimental and field settings. Participants viewed a five-minute…

Multi-component testing using HZ-PAN and AgZ-PAN Sorbents for OSPREY Model validation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garn, Troy G.; Greenhalgh, Mitchell; Lyon, Kevin L.

2015-04-01

In efforts to further develop the capability of the Off-gas SeParation and RecoverY (OSPREY) model, multi-component tests were completed using both HZ-PAN and AgZ-PAN sorbents. The primary purpose of this effort was to obtain multi-component xenon and krypton capacities for comparison to future OSPREY predicted multi-component capacities using previously acquired Langmuir equilibrium parameters determined from single component isotherms. Experimental capacities were determined for each sorbent using two feed gas compositions of 1000 ppmv xenon and 150 ppmv krypton in either a helium or air balance. Test temperatures were consistently held at 220 K and the gas flowrate was 50 sccm.more » Capacities were calculated from breakthrough curves using TableCurve® 2D software by Jandel Scientific. The HZ-PAN sorbent was tested in the custom designed cryostat while the AgZ-PAN was tested in a newly installed cooling apparatus. Previous modeling validation efforts indicated the OSPREY model can be used to effectively predict single component xenon and krypton capacities for both engineered form sorbents. Results indicated good agreement with the experimental and predicted capacity values for both krypton and xenon on the sorbents. Overall, the model predicted slightly elevated capacities for both gases which can be partially attributed to the estimation of the parameters and the uncertainty associated with the experimental measurements. Currently, OSPREY is configured such that one species adsorbs and one does not (i.e. krypton in helium). Modification of OSPREY code is currently being performed to incorporate multiple adsorbing species and non-ideal interactions of gas phase species with the sorbent and adsorbed phases. Once these modifications are complete, the sorbent capacities determined in the present work will be used to validate OSPREY multicomponent adsorption predictions.« less

Adaptive Control of Truss Structures for Gossamer Spacecraft

NASA Technical Reports Server (NTRS)

Yang, Bong-Jun; Calise, Anthony J.; Craig, James I.; Whorton, Mark S.

2007-01-01

Neural network-based adaptive control is considered for active control of a highly flexible truss structure which may be used to support solar sail membranes. The objective is to suppress unwanted vibrations in SAFE (Solar Array Flight Experiment) boom, a test-bed located at NASA. Compared to previous tests that restrained truss structures in planar motion, full three dimensional motions are tested. Experimental results illustrate the potential of adaptive control in compensating for nonlinear actuation and modeling error, and in rejecting external disturbances.

Quarantine testing and biocharacterization of lunar materials

NASA Technical Reports Server (NTRS)

Taylor, G. R.; Mieszkuc, B. J.; Simmonds, R. C.; Walkinshaw, C. H.

1975-01-01

Quarantine testing was conducted to ensure the safety of all life on earth. The plants and animals which were exposed to lunar material were carefully observed for prolonged periods to determine if any mutation or changes in growing characteristics and behavior occurred. The quarantine testing was terminated after the Apollo 14 flight when it became apparent that previously returned lunar material contained no potentially harmful agents. Further biological experimentation with the lunar material was conducted to determine its chemical, physical, and nutritional qualities.

Behavioral Effects of Tyrosine during Sustained Wakefulness,

DTIC Science & Technology

1993-12-01

with approximately 113 g of banana-flavored yogurt and administered to the subjects in a double- blind procedure. Previous testing with research...staff indicated that cornstarch mixed with 113 g of banana yogurt is indistinguishable in taste, texture, and appearance from tyrosine mixed with the same...quantity of banana yogurt . Table 1. Experimental Task Order and Duration (min). Test Duration Cumulative duration VAS/SSS 04 04 Tracking 10 14 Break

Some recent developments in the Wind River Douglas-fir plantation spacing tests.

Treesearch

Donald L. Reukema

1959-01-01

The effect of spacing on stand development is a subject that has been widely discussed. To test spacings ranging from 4x4 feet to 12x12 feet, a Douglas-fir plantation was established in 1925 at the Wind River Experimental Forest near Carson, Wash. This paper reports some results of a remeasurement made in 1957 (table 1) and compares these results with those of previous...

Does Humor Have an Effect on the Performance of College Freshmen in Improving Scores on the Nelson Denny Reading Post Test?

ERIC Educational Resources Information Center

Schiller, Maryann F.

A study was conducted to investigate the effects of humor on the performance of college freshmen on the Nelson Denny Reading Post Test. The subjects, 36 college freshmen from two developmental reading improvement classes, were randomly assigned to experimental A or B or control sample groups. Students had previously taken forms F and C of the test…

Supersonic Retropropulsion Experimental Results from the NASA Ames 9- x 7-Foot Supersonic Wind Tunnel

NASA Technical Reports Server (NTRS)

Berry, Scott A.; Rhode, Matthew N.; Edquist, Karl T.

2012-01-01

Supersonic retropropulsion was experimentally examined in the Ames Research Center 9x7-Foot Supersonic Wind Tunnel at Mach 1.8 and 2.4. The experimental model, previously designed for and tested in the Langley Research Center Unitary Plan Wind Tunnel at Mach 2.4, 3.5 and 4.6, was a 5-in diameter 70-deg sphere-cone forebody with a 9.55-in long cylindrical aftbody. The forebody was designed to accommodate up to four 4:1 area ratio nozzles, one on the model centerline and the other three on the half radius spaced 120-deg apart. Surface pressure and flow visualization were the primary measurements, including high-speed data to investigate the dynamics of the interactions between the bow and nozzle shocks. Three blowing configurations were tested with thrust coefficients up to 10 and angles of attack up to 20-deg. Preliminary results and observations from the test are provided

Fan Flutter Computations Using the Harmonic Balance Method

NASA Technical Reports Server (NTRS)

Bakhle, Milind A.; Thomas, Jeffrey P.; Reddy, T.S.R.

2009-01-01

An experimental forward-swept fan encountered flutter at part-speed conditions during wind tunnel testing. A new propulsion aeroelasticity code, based on a computational fluid dynamics (CFD) approach, was used to model the aeroelastic behavior of this fan. This threedimensional code models the unsteady flowfield due to blade vibrations using a harmonic balance method to solve the Navier-Stokes equations. This paper describes the flutter calculations and compares the results to experimental measurements and previous results from a time-accurate propulsion aeroelasticity code.

Detection of antibodies to single-stranded DNA in naturally acquired and experimentally induced viral hepatitis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gust, I.D.; Feinstone, S.M.; Purcell, R.H.

1980-01-01

A sensitive ''Farr'' assay, utilizing /sup 125/I-labelled DNA was developed for detecting antibody to single-stranded DNA (anti-ssDNA). The test was shown to be specific and as sensitive as assays using /sup 14/C-labelled DNA, for the detection of antibody in patients with connective tissue diseases. Groups of sera from patients with naturally acquired viral hepatitis and experimentally infected chimpanzees were tested for anti-ssDNA by the /sup 125/I assay and by counterimmunoelectrophoresis (CIEP). No consistent pattern was observed with either technique, indicating the elevated levels of this antibody are not as reliable markers of parenchymal liver damage as had been previously suggested.

Conceptual design of a closed loop nutrient solution delivery system for CELSS implementation in a micro-gravity environment

NASA Technical Reports Server (NTRS)

Schwartzkopf, Steven H.; Oleson, Mel W.; Cullingford, Hatice S.

1990-01-01

Described here are the results of a study to develop a conceptual design for an experimental closed loop fluid handling system capable of monitoring, controlling, and supplying nutrient solution to higher plants. The Plant Feeder Experiment (PFE) is designed to be flight tested in a microgravity environment. When flown, the PFX will provide information on both the generic problems of microgravity fluid handling and the specific problems associated with the delivery of the nutrient solution in a microgravity environment. The experimental hardware is designed to fit into two middeck lockers on the Space Shuttle, and incorporates several components that have previously been flight tested.

A Taphonomic Study Exploring the Differences in Decomposition Rate and Manner between Frozen and Never Frozen Domestic Pigs (Sus scrofa).

PubMed

Roberts, Lindsey G; Dabbs, Gretchen R

2015-05-01

This research examined differences in decomposition rate and manner of domestic pig subjects (Sus scrofa) in never frozen (control) and previously frozen (experimental) research conditions. Eight control and experimental subjects were placed in an identical outdoor research environment. Daily quantitative and qualitative measurements were collected: abdominal circumference, total body score (TBS), temperature, photographs, descriptive decomposition stages, and visual observations. Field necropsies were performed at accumulated degree days (ADD) between 50 and 300 (Celsius). Paired samples t-tests of ADD to TBS >3.0, TBS >9.5, and TBS >16.0 indicate the rate of decomposition of experimental subjects was significantly slower than controls at both TBS >3 and >9.5 (p = 0.003 and p = 0.002, respectively). A suite of qualitative indicators of predecomposition freezing is also reported. The differences between experimental and control subjects suggest previously frozen subjects should not be used in taphonomic research, as results do not accurately reflect the "normal" taphonomic condition. © 2015 American Academy of Forensic Sciences.

Do You Have to be Angry to be Aggressive?

ERIC Educational Resources Information Center

Wienir, Paul L.

Seven hypotheses regarding the role of anger for aggressive behavior were testes in an experimental exchange situation using male children as subjects. In previous studies, anger had not actually been employed as the intervening variable in a provocation/aggressive cue-aggression model. The results indicate a strong relationship between…

Misconduct in the Prosecution of Severe Crimes: Theory and Experimental Test

ERIC Educational Resources Information Center

Lucas, Jeffrey W.; Graif, Corina; Lovaglia, Michael J.

2006-01-01

Prosecutorial misconduct involves the intentional use of illegal or improper methods for attaining convictions against defendants in criminal trials. Previous research documented extensive errors in the prosecution of severe crimes. A theory formulated to explain this phenomenon proposes that in serious cases, increased pressure to convict…

Characterization of mechanical properties of pericardium tissue using planar biaxial tension and flexural deformation.

PubMed

Murdock, Kyle; Martin, Caitlin; Sun, Wei

2018-01-01

Flexure is an important mode of deformation for native and bioprosthetic heart valves. However, mechanical characterization of bioprosthetic leaflet materials has been done primarily through planar tensile testing. In this study, an integrated experimental and computational cantilever beam bending test was performed to characterize the flexural properties of glutaraldehyde-treated bovine and porcine pericardium of different thicknesses. A strain-invariant based structural constitutive model was used to model the pericardial mechanical behavior quantified through the bending tests of this study and the planar biaxial tests previously performed. The model parameters were optimized through an inverse finite element (FE) procedure in order to describe both sets of experimental data. The optimized material properties were implemented in FE simulations of transcatheter aortic valve (TAV) deformation. It was observed that porcine pericardium TAV leaflets experienced significantly more flexure than bovine when subjected to opening pressurization, and that the flexure may be overestimated using a constitutive model derived from purely planar tensile experimental data. Thus, modeling of a combination of flexural and biaxial tensile testing data may be necessary to more accurately describe the mechanical properties of pericardium, and to computationally investigate bioprosthetic leaflet function and design. Copyright © 2017 Elsevier Ltd. All rights reserved.

An experimental approach in revisiting the magnetic orientation of cattle.

PubMed

Weijers, Debby; Hemerik, Lia; Heitkönig, Ignas M A

2018-01-01

In response to the increasing number of observational studies on an apparent south-north orientation in non-homing, non-migrating terrestrial mammals, we experimentally tested the alignment hypothesis using strong neodymium magnets on the resting orientation of individual cattle in Portugal. Contrary to the hypothesis, the 34 cows in the experiment showed no directional preference, neither with, nor without a strong neodymium magnet fixed to their collar. The concurrently performed 2,428 daytime observations-excluding the hottest part of the day-of 659 resting individual cattle did not show a south-north alignment when at rest either. The preferred compass orientation of these cows was on average 130 degrees from the magnetic north (i.e., south east). Cow compass orientation correlated significantly with sun direction, but not with wind direction. In as far as we can determine, this is the first experimental test on magnetic orientation in larger, non-homing, non-migrating mammals. These experimental and observational findings do not support previously published suggestions on the magnetic south-north alignment in these mammals.

FELASA recommendations for the health monitoring of mouse, rat, hamster, guinea pig and rabbit colonies in breeding and experimental units.

PubMed

Mähler Convenor, M; Berard, M; Feinstein, R; Gallagher, A; Illgen-Wilcke, B; Pritchett-Corning, K; Raspa, M

2014-07-01

The microbiological quality of experimental animals can critically influence animal welfare and the validity and reproducibility of research data. It is therefore important for breeding and experimental facilities to establish a laboratory animal health monitoring (HM) programme as an integrated part of any quality assurance system. FELASA has published recommendations for the HM of rodent and rabbit colonies in breeding and experimental units (Nicklas et al. Laboratory Animals, 2002), with the intention of harmonizing HM programmes. As stated in the preamble, these recommendations need to be adapted periodically to meet current developments in laboratory animal medicine. Accordingly, previous recommendations have been revised and shall be replaced by the present recommendations. These recommendations are aimed at all breeders and users of laboratory mice, rats, Syrian hamsters, guinea pigs and rabbits as well as diagnostic laboratories. They describe essential aspects of HM, such as the choice of agents, selection of animals and tissues for testing, frequency of sampling, commonly used test methods, interpretation of results and HM reporting. Compared with previous recommendations, more emphasis is put on the role of a person with sufficient understanding of the principles of HM, opportunistic agents, the use of sentinel animals (particularly under conditions of cage-level containment) and the interpretation and reporting of HM results. Relevant agents, testing frequencies and literature references are updated. Supplementary information on specific agents and the number of animals to be monitored and an example of a HM programme description is provided in the appendices. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Digital evaluation of sitting posture comfort in human-vehicle system under Industry 4.0 framework

NASA Astrophysics Data System (ADS)

Tao, Qing; Kang, Jinsheng; Sun, Wenlei; Li, Zhaobo; Huo, Xiao

2016-09-01

Most of the previous studies on the vibration ride comfort of the human-vehicle system were focused only on one or two aspects of the investigation. A hybrid approach which integrates all kinds of investigation methods in real environment and virtual environment is described. The real experimental environment includes the WBV(whole body vibration) test, questionnaires for human subjective sensation and motion capture. The virtual experimental environment includes the theoretical calculation on simplified 5-DOF human body vibration model, the vibration simulation and analysis within ADAMS/VibrationTM module, and the digital human biomechanics and occupational health analysis in Jack software. While the real experimental environment provides realistic and accurate test results, it also serves as core and validation for the virtual experimental environment. The virtual experimental environment takes full advantages of current available vibration simulation and digital human modelling software, and makes it possible to evaluate the sitting posture comfort in a human-vehicle system with various human anthropometric parameters. How this digital evaluation system for car seat comfort design is fitted in the Industry 4.0 framework is also proposed.

Magnetic and Electrical Characteristics of Permalloy Thin Tape Bobbin Cores

NASA Technical Reports Server (NTRS)

Schwarze, Gene E.; Wieserman, William R.; Niedra, Janis M.

2005-01-01

The core loss, that is, the power loss, of a soft ferromagnetic material is a function of the flux density, frequency, temperature, excitation type (voltage or current), excitation waveform (sine, square, etc.) and lamination or tape thickness. In previously published papers we have reported on the specific core loss and dynamic B-H loop results for several polycrystalline, nanocrystalline, and amorphous soft magnetic materials. In this previous research we investigated the effect of flux density, frequency, temperature, and excitation waveform for voltage excitation on the specific core loss and dynamic B-H loop. In this paper, we will report on an experimental study to investigate the effect of tape thicknesses of 1, 1/2, 1/4, and 1/8-mil Permalloy type magnetic materials on the specific core loss. The test cores were fabricated by winding the thin tapes on ceramic bobbin cores. The specific core loss tests were conducted at room temperature and over the frequency range of 10 kHz to 750 kHz using sine wave voltage excitation. The results of this experimental investigation will be presented primarily in graphical form to show the effect of tape thickness, frequency, and magnetic flux density on the specific core loss. Also, the experimental results when applied to power transformer design will be briefly discussed.

Skeletal pattern in subjects with temporomandibular joint disorders

PubMed Central

Almăşan, Oana Cristina; Almăşan, Horea Artimoniu; Bran, Simion; Lascu, Liana; Iancu, Mihaela; Băciuţ, Grigore

2013-01-01

Introduction To establish the skeletal pattern in subjects with malocclusions and temporomandibular disorders (TMD); to assess the relationship between craniofacial skeletal structures and TMD in subjects with malocclusions. Material and methods Sixty-four subjects with malocclusions, over 18 years of age, were included in the study. Temporomandibular disorders were clinically assessed according to the Helkimo Anamnestic Index. Subjects underwent a lateral cephalogram. Subjects were grouped according to the sagittal skeletal pattern (ANB angle) into class I, II and III. Parametric Student tests with equal or unequal variations were used (variations were previously tested with Levene test). Results Twenty-four patients with TMD (experimental sample); 40 patients without TMD (control group); interincisal angle was higher in class I and II (p < 0.05) experimental subjects; overjet was larger in experimental subjects; midline shift and Wits appraisal were broader in the experimental group in all three classes. In class III subjects, the SNB angle was higher in the experimental group (p = 0.01). Joint noises followed by reduced mandible mobility, muscular pain and temporomandibular joint (TMJ) pain were the most frequent symptoms in subjects with TMD and malocclusions. Conclusions Temporomandibular joint status is an important factor to consider when planning orthodontic treatment in patients with severe malocclusions; midline shift, large overjet and deep overbite have been associated with signs and symptoms of TMD. PMID:23515361

An Experimental Study of Pressure Oscillation in a Capillary Pumped Loop with Multiple Evaporators and Condensers

NASA Technical Reports Server (NTRS)

Ku, Jen-Tung; Hoang, Triem T.

1998-01-01

The heat transport capability of a capillary pumped loop (CPL) is limited by the pressure drop that its evaporator wick can sustain. The pressure drop in a CPL is not constant even under seemingly steady operation, but rather exhibits an oscillatory behavior. A hydrodynamic theory based on a mass-spring-dashpot model was previously developed to predict the pressure oscillation in a CPL with a single evaporator and a single condenser. The theory states that the pressure oscillation is a function of physical dimensions of the CPL components and operating conditions. Experimental data agreed very well with theoretical predictions. The hydrodynamic stability theory has recently been extended to predict the pressure oscillations in CPLs with multiple evaporators and multiple condensers. Concurrently, an experimental study was conducted to verify the theory and to investigate the effects of various parameters on the pressure oscillation. Four evaporators with different wick properties were tested using a test loop containing two condenser plates. The test loop allowed the four evaporators to be tested in a single-pump, two-pump or four-pump configuration, and the two condenser plates to be plumbed either in parallel or in series. Test conditions included varying the power input, the reservoir set point temperature, the condenser sink temperature, and the flow resistance between the reservoir and the loop. Experimental results agreed well with theoretical predictions.

Executive function on the Psychology Experiment Building Language tests.

PubMed

Piper, Brian J; Li, Victoria; Eiwaz, Massarra A; Kobel, Yuliyana V; Benice, Ted S; Chu, Alex M; Olsen, Reid H J; Rice, Douglas Z; Gray, Hilary M; Mueller, Shane T; Raber, Jacob

2012-03-01

The measurement of executive function has a long history in clinical and experimental neuropsychology. The goal of the present report was to determine the profile of behavior across the lifespan on four computerized measures of executive function contained in the recently developed Psychology Experiment Building Language (PEBL) test battery http://pebl.sourceforge.net/ and evaluate whether this pattern is comparable to data previously obtained with the non-PEBL versions of these tests. Participants (N = 1,223; ages, 5-89 years) completed the PEBL Trail Making Test (pTMT), the Wisconsin Card Sort Test (pWCST; Berg, Journal of General Psychology, 39, 15-22, 1948; Grant & Berg, Journal of Experimental Psychology, 38, 404-411, 1948), the Tower of London (pToL), or a time estimation task (Time-Wall). Age-related effects were found over all four tests, especially as age increased from young childhood through adulthood. For several tests and measures (including pToL and pTMT), age-related slowing was found as age increased in adulthood. Together, these findings indicate that the PEBL tests provide valid and versatile new research tools for measuring executive functions.

Measurement and prediction of the thermomechanical response of shape memory alloy hybrid composite beams

NASA Astrophysics Data System (ADS)

Davis, Brian; Turner, Travis L.; Seelecke, Stefan

2005-05-01

Previous work at NASA Langley Research Center (LaRC) involved fabrication and testing of composite beams with embedded, pre-strained shape memory alloy (SMA) ribbons within the beam structures. That study also provided comparison of experimental results with numerical predictions from a research code making use of a new thermoelastic model for shape memory alloy hybrid composite (SMAHC) structures. The previous work showed qualitative validation of the numerical model. However, deficiencies in the experimental-numerical correlation were noted and hypotheses for the discrepancies were given for further investigation. The goal of this work is to refine the experimental measurement and numerical modeling approaches in order to better understand the discrepancies, improve the correlation between prediction and measurement, and provide rigorous quantitative validation of the numerical analysis/design tool. The experimental investigation is refined by a more thorough test procedure and incorporation of higher fidelity measurements such as infrared thermography and projection moire interferometry. The numerical results are produced by a recently commercialized version of the constitutive model as implemented in ABAQUS and are refined by incorporation of additional measured parameters such as geometric imperfection. Thermal buckling, post-buckling, and random responses to thermal and inertial (base acceleration) loads are studied. The results demonstrate the effectiveness of SMAHC structures in controlling static and dynamic responses by adaptive stiffening. Excellent agreement is achieved between the predicted and measured results of the static and dynamic thermomechanical response, thereby providing quantitative validation of the numerical tool.

Measurement and Prediction of the Thermomechanical Response of Shape Memory Alloy Hybrid Composite Beams

NASA Technical Reports Server (NTRS)

Davis, Brian; Turner, Travis L.; Seelecke, Stefan

2005-01-01

Previous work at NASA Langley Research Center (LaRC) involved fabrication and testing of composite beams with embedded, pre-strained shape memory alloy (SMA) ribbons within the beam structures. That study also provided comparison of experimental results with numerical predictions from a research code making use of a new thermoelastic model for shape memory alloy hybrid composite (SMAHC) structures. The previous work showed qualitative validation of the numerical model. However, deficiencies in the experimental-numerical correlation were noted and hypotheses for the discrepancies were given for further investigation. The goal of this work is to refine the experimental measurement and numerical modeling approaches in order to better understand the discrepancies, improve the correlation between prediction and measurement, and provide rigorous quantitative validation of the numerical analysis/design tool. The experimental investigation is refined by a more thorough test procedure and incorporation of higher fidelity measurements such as infrared thermography and projection moire interferometry. The numerical results are produced by a recently commercialized version of the constitutive model as implemented in ABAQUS and are refined by incorporation of additional measured parameters such as geometric imperfection. Thermal buckling, post-buckling, and random responses to thermal and inertial (base acceleration) loads are studied. The results demonstrate the effectiveness of SMAHC structures in controlling static and dynamic responses by adaptive stiffening. Excellent agreement is achieved between the predicted and measured results of the static and dynamic thermomechanical response, thereby providing quantitative validation of the numerical tool.

New experimental stopping power data of 4He, 16O, 40Ar, 48Ca and 84Kr projectiles in different solid materials

NASA Astrophysics Data System (ADS)

Trzaska, W. H.; Knyazheva, G. N.; Perkowski, J.; Andrzejewski, J.; Khlebnikov, S. V.; Kozulin, E. M.; Malkiewicz, T.; Mutterer, M.; Savelieva, E. O.

2018-03-01

New experimental data on energy loss of 4He, 16O, 40Ar, 48Ca and 84Kr ions in thin, self-supporting foils of C, Al, Ni, Ag, Lu, Au, Pb and Th are presented. The measurements, using the TOF-E method, were done in a very broad energy range around the stopping power maximum; typically from 0.1 to 11 MeV/u. When available, the extracted stopping power values are compared with the previously published data. The overall agreement is good although a fair comparison is difficult as the covered energy range is much larger than in previous measurements. The small error bars and a broad coverage allowed us to test the predictions of theoretical codes: PASS, CasP, and semi-empirical programs: SRIM, LET, MSTAR, and the Hubert table predictions. The deviations of PASS predictions from the experimental data do not exceed 20% for all the measured combinations. CasP predictions are within 15% from the data for heavier ions but diverge up to 40% for lighter ions. Semi-empirical approaches, including SRIM, deviate from the experimental data by less than 5% for the regions already covered by previous experiments but err by about 10-20% for the ion/target combinations that were not measured before: Ca in Lu as well as Kr in Lu, Pb, and Th.

Enzymatic Kinetic Isotope Effects from First-Principles Path Sampling Calculations.

PubMed

Varga, Matthew J; Schwartz, Steven D

2016-04-12

In this study, we develop and test a method to determine the rate of particle transfer and kinetic isotope effects in enzymatic reactions, specifically yeast alcohol dehydrogenase (YADH), from first-principles. Transition path sampling (TPS) and normal mode centroid dynamics (CMD) are used to simulate these enzymatic reactions without knowledge of their reaction coordinates and with the inclusion of quantum effects, such as zero-point energy and tunneling, on the transferring particle. Though previous studies have used TPS to calculate reaction rate constants in various model and real systems, it has not been applied to a system as large as YADH. The calculated primary H/D kinetic isotope effect agrees with previously reported experimental results, within experimental error. The kinetic isotope effects calculated with this method correspond to the kinetic isotope effect of the transfer event itself. The results reported here show that the kinetic isotope effects calculated from first-principles, purely for barrier passage, can be used to predict experimental kinetic isotope effects in enzymatic systems.

Experiments and analysis of a compact electrothermal thruster

NASA Technical Reports Server (NTRS)

Asmussen, Jes; Whitehair, Stan

1988-01-01

The description and experimental performance of a compact microwave electrothermal thruster (MET) are presented. This thruster uses a coaxial applicator to couple microwave power into a high pressure discharge. Unlike earlier experiments, it uses no fused quartz in the discharge chamber or the nozzle. This allows high temperatures in the discharge chamber without quartz erosion and melting, thereby improving thruster performance and lifetime. The thruster design is compact, enhancing its potential as a space engine. Experimental tests using nitrogen and helium propellants with input powers levels of 200 W to 1.5 kW are presented. Experimental results, which produce energy efficiencies of 20 to 60 percent and specific impulse of 250 to 450 sec, compare favorably to previous experimental MET performance.

Inhalability for aerosols at ultra-low windspeeds

NASA Astrophysics Data System (ADS)

Sleeth, Darrah K.; Vincent, James H.

2009-02-01

Most previous experimental studies of aerosol inhalability were conducted in wind tunnels for windspeeds greater than 0.5 ms-1. While that body of work was used to establish a convention for the inhalable fraction, results from studies in calm air chambers (for essentially zero windspeed) are being discussed as the basis of a modified criterion. However, information is lacking for windspeeds in the intermediate range, which - it so happens - pertain to most actual workplaces. With this in mind, we have developed a new experimental system to assess inhalability - and, ultimately, personal sampler performance - for aerosols with particle aerodynamic diameter within the range from about 9 to 90 μm for ultra-low windspeed environments from about 0.1 to 0.5 ms1. This new system contains an aerosol test facility, fully described elsewhere, that combines the physical attributes and performance characteristics of moving air wind tunnels and calm air chambers, both of which have featured individually in previous research. It also contains a specially-designed breathing, heated, life-sized mannequin that allows for accurate recovery of test particulate material that has been inhaled. Procedures have been developed that employ test aerosols of well-defined particle size distribution generated mechanically from narrowly-graded powders of fused alumina. Using this new system, we have conducted an extensive set of new experiments to measure the inhalability of a human subject (as represented by the mannequin), aimed at filling the current knowledge gap for conditions that are more realistic than those embodied in most previous research. These data reveal that inhalability throughout the range of interest is significantly different based on windspeed, indicating a rise in aspiration efficiency as windspeed decreases. Breathing flowrate and mode of breathing (i.e. nose versus mouth breathing) did not show significant differences for the inhalability of aerosols. On the whole however, the data obtained here are within the range of inhalability data that exist from the large body of the previous experimental work performed at the higher windspeeds. These latest findings are an important contribution to the ongoing discussion in international standards-setting bodies about the possible adjustment of the quantitative definition of what constitutes the inhalable fraction.

The performance of cleaner wrasse, Labroides dimidiatus, in a reversal learning task varies across experimental paradigms.

PubMed

Gingins, Simon; Marcadier, Fanny; Wismer, Sharon; Krattinger, Océane; Quattrini, Fausto; Bshary, Redouan; Binning, Sandra A

2018-01-01

Testing performance in controlled laboratory experiments is a powerful tool for understanding the extent and evolution of cognitive abilities in non-human animals. However, cognitive testing is prone to a number of potential biases, which, if unnoticed or unaccounted for, may affect the conclusions drawn. We examined whether slight modifications to the experimental procedure and apparatus used in a spatial task and reversal learning task affected performance outcomes in the bluestreak cleaner wrasse, Labroides dimidiatus (hereafter "cleaners"). Using two-alternative forced-choice tests, fish had to learn to associate a food reward with a side (left or right) in their holding aquarium. Individuals were tested in one of four experimental treatments that differed slightly in procedure and/or physical set-up. Cleaners from all four treatment groups were equally able to solve the initial spatial task. However, groups differed in their ability to solve the reversal learning task: no individuals solved the reversal task when tested in small tanks with a transparent partition separating the two options, whereas over 50% of individuals solved the task when performed in a larger tank, or with an opaque partition. These results clearly show that seemingly insignificant details to the experimental set-up matter when testing performance in a spatial task and might significantly influence the outcome of experiments. These results echo previous calls for researchers to exercise caution when designing methodologies for cognition tasks to avoid misinterpretations.

Numerical Modeling of Gas Turbine Combustor Utilizing One-Dimensional Acoustics

NASA Astrophysics Data System (ADS)

Caley, Thomas M.

This study focuses on the numerical modeling of a gas turbine combustor set-up with known regions of thermoacoustic instability. The proposed model takes the form of a hybrid thermoacoustic network, with lumped elements representing boundary conditions and the flame, and 3-dimensional geometry volumes representing the geometry. The model is analyzed using a commercial 3-D finite element method (FEM) software, COMSOL Multiphysics. A great deal of literature is available covering thermoacoustic modeling, but much of it utilizes more computationally expensive techniques such as Large-Eddy Simulations, or relies on analytical modeling that is limited to specific test cases or proprietary software. The present study models the 3-D geometry of a high-pressure combustion chamber accurately, and uses the lumped elements of a thermoacoustic network to represent parts of the combustor system that can be experimentally tested under stable conditions, ensuring that the recorded acoustic responses can be attributed to that element alone. The numerical model has been tested against the experimental model with and without an experimentally-determined impedance boundary condition. Eigenfrequency studies are used to compare the frequency and growth rates (and from that, the thermoacoustic stability) of resonant modes in the combustor. The flame in the combustor is modeled with a flame transfer function that was determined from experimental testing using frequency forcing. The effect of flow rate on the impedance boundary condition is also examined experimentally and numerically to qualify the practice of modeling an orifice plate as an acoustically-closed boundary. Using the experimental flame transfer function and boundary conditions in the numerical model produced results that closely matched previous experimental tests in frequency, but not in stability characteristics. The lightweight nature of the numerical model means additional lumped elements can be easily added when experimental data is available, creating a more accurate model without noticeably increasing the complexity or computational time.

High temperature, low-cycle fatigue of copper-base alloys for rocket nozzles. Part 2: Strainrange partitioning and low-cycle fatigue results at 538 deg C

NASA Technical Reports Server (NTRS)

Conway, J. B.; Stentz, R. H.; Berling, J. T.

1976-01-01

Low-cycle fatigue tests of 1/2 Hard AMZIRC Copper and NARloy Z were performed in argon at 538 C to determine partitioned strain range versus life relationships. Strain-controlled low-cycle fatigue tests of a Zr-Cr-Mg copper-base alloy were also performed. Strain ranges, lower than those employed in previous tests, were imposed in order to extend the fatigue life curve out to approximately 400,000 cycles. An experimental copper alloy and an experimental silver alloy were also studied. Tensile tests were performed in air at room temperature and in argon at 538 C. Strain-controlled low-cycle fatigue tests were performed at 538 C in argon to define the fatigue life over the regime from 300 to 3,000 cycles. For the silver alloy, three additional heat treatments were introduced, and a limited evaluation of the short-term tensile and low-cycle fatigue behavior at 538 C was performed.

Exploring Techniques of Developing Writing Skill in IELTS Preparatory Courses: A Data-Driven Study

ERIC Educational Resources Information Center

Ostovar-Namaghi, Seyyed Ali; Safaee, Seyyed Esmail

2017-01-01

Being driven by the hypothetico-deductive mode of inquiry, previous studies have tested the effectiveness of theory-driven interventions under controlled experimental conditions to come up with universally applicable generalizations. To make a case in the opposite direction, this data-driven study aims at uncovering techniques and strategies…

Effects of the Integrated Online Advance Organizer Teaching Materials on Students' Science Achievement and Attitude

ERIC Educational Resources Information Center

Korur, Fikret; Toker, Sacip; Eryilmaz, Ali

2016-01-01

This two-group quasi-experimental study investigated the effects of the Online Advance Organizer Concept Teaching Material (ONACOM) integrated with inquiry teaching and expository teaching methods. Grade 7 students' posttest performances on the light unit achievement and light unit attitude tests controlled for gender, previous semester science…

The TRIPSE: A Process-Oriented Exam for Large Undergraduate Classes

ERIC Educational Resources Information Center

Nastos, Stash; Rangachari, P. K.

2013-01-01

The TRIPSE (tri-partite problem solving exercise), a process-oriented exam that mimics the scientific process, was used previously in small classes (15-25). Provided limited data, students frame explanations and design experimental tests that they later revise with additional information. Our 6-year experience using it with larger numbers…

No Sex Differences in Spatial Location Memory for Abstract Designs

ERIC Educational Resources Information Center

Rahman, Qazi; Bakare, Monsurat; Serinsu, Ceydan

2011-01-01

Previous research has demonstrated a female advantage, albeit imperfectly, on tests of object location memory where object identity information is readily available. However, spatial and visual elements are often confounded in the experimental tasks used. Here spatial and visual memory performance was compared in 30 men and 30 women by presenting…

Fixation-Dependent Memory for Natural Scenes: An Experimental Test of Scanpath Theory

ERIC Educational Resources Information Center

Foulsham, Tom; Kingstone, Alan

2013-01-01

Many modern theories propose that perceptual information is represented by the sensorimotor activity elicited by the original stimulus. Scanpath theory (Noton & Stark, 1971) predicts that reinstating a sequence of eye fixations will help an observer recognize a previously seen image. However, the only studies to investigate this are…

Survival of bighorn sheep (Ovis canadensis) commingled with domestic sheep (Ovis aries) in the absence of mycoplasma ovipneumoniae.

USDA-ARS?s Scientific Manuscript database

To test the hypothesis that Mycoplasma ovipneumoniae is an important agent of the bighorn sheep (Ovis canadensis) pneumonia that has previously inevitably followed experimental commingling with domestic sheep (Ovis aries), we commingled M. ovipneumoniae–free domestic and bighorn sheep (n=4 each). On...

The Effects of Arts Integration on Long-Term Retention of Academic Content

ERIC Educational Resources Information Center

Hardiman, Mariale; Rinne, Luke; Yarmolinskaya, Julia

2014-01-01

Previous correlational and quasi-experimental studies of arts integration--the pedagogical practice of "teaching through the arts"--suggest its value for enhancing cognitive, academic, and social skills. This study reports the results of a small, preliminary classroom-based experiment that tested effects of arts integration on long-term…

Towards Loophole-Free Optical Bell Test of CHSH Inequality

NASA Astrophysics Data System (ADS)

Tan, Yong-gang; Li, Hong-wei

2016-09-01

Bell test had been suggested to end the long-standing debate on the EPR paradox, while the imperfections of experimental devices induce some loopholes in Bell test experiments and hence the assumption of local reality by EPR cannot be excluded with current experimental results. In optical Bell test experiments, the locality loophole can be closed easily, while the attempt of closing detection loophole requires very high efficiency of single photon detectors. Previous studies showed that the violation of Clauser-Horne-Shimony-Holt (CHSH) inequality with maximally entangled states requires the detection efficiency to be higher than 82.8 %. In this paper, we raise a modified CHSH inequality that covers all measurement events including the efficient and inefficient detections in the Bell test and prove that all local hidden models can be excluded when the inequality is violated. We find that, when non-maximally entangled states are applied to the Bell test, the lowest detection efficiency for violation of the present inequality is 66.7 %. This makes it feasible to close the detection loophole and the locality loophole simultaneously in optical Bell test of CHSH inequality.

Measurement of Unsteady Pressure Data on a Large HSCT Semispan Wing and Comparison with Analysis

NASA Technical Reports Server (NTRS)

Scott, Robert C.; Silva, Walter A.; Florance, James R.; Keller, Donald F.

2002-01-01

Experimental data from wind-tunnel tests of the Rigid Semispan Model (RSM) performed at NASA Langley's Transonic Dynamics Tunnel (TDT) are presented. The primary focus of the paper is on data obtained from testing of the RSM on the Oscillating Turntable (OTT). The OTT is capable of oscillating models in pitch at various amplitudes and frequencies about mean angles of attack. Steady and unsteady pressure data obtained during testing of the RSM on the OTT is presented and compared to data obtained from previous tests of the RSM on a load balance and on a Pitch and Plunge Apparatus (PAPA). Testing of the RSM on the PAPA resulted in utter boundaries that were strongly dependent on angle of attack across the Mach number range. Pressure data from all three tests indicates the existence of vortical flows at moderate angles of attack. The correlation between the vortical flows and the unusual utter boundaries from the RSM/PAPA test is discussed. Comparisons of experimental data with analyses using the CFL3Dv6 computational fluid dynamics code are presented.

Structural Analysis and Testing of an Erectable Truss for Precision Segmented Reflector Application

NASA Technical Reports Server (NTRS)

Collins, Timothy J.; Fichter, W. B.; Adams, Richard R.; Javeed, Mehzad

1995-01-01

This paper describes analysis and test results obtained at Langley Research Center (LaRC) on a doubly curved testbed support truss for precision reflector applications. Descriptions of test procedures and experimental results that expand upon previous investigations are presented. A brief description of the truss is given, and finite-element-analysis models are described. Static-load and vibration test procedures are discussed, and experimental results are shown to be repeatable and in generally good agreement with linear finite-element predictions. Truss structural performance (as determined by static deflection and vibration testing) is shown to be predictable and very close to linear. Vibration test results presented herein confirm that an anomalous mode observed during initial testing was due to the flexibility of the truss support system. Photogrammetric surveys with two 131-in. reference scales show that the root-mean-square (rms) truss-surface accuracy is about 0.0025 in. Photogrammetric measurements also indicate that the truss coefficient of thermal expansion (CTE) is in good agreement with that predicted by analysis. A detailed description of the photogrammetric procedures is included as an appendix.

Prediction of Multi-Target Networks of Neuroprotective Compounds with Entropy Indices and Synthesis, Assay, and Theoretical Study of New Asymmetric 1,2-Rasagiline Carbamates

PubMed Central

Romero Durán, Francisco J.; Alonso, Nerea; Caamaño, Olga; García-Mera, Xerardo; Yañez, Matilde; Prado-Prado, Francisco J.; González-Díaz, Humberto

2014-01-01

In a multi-target complex network, the links (Lij) represent the interactions between the drug (di) and the target (tj), characterized by different experimental measures (Ki, Km, IC50, etc.) obtained in pharmacological assays under diverse boundary conditions (cj). In this work, we handle Shannon entropy measures for developing a model encompassing a multi-target network of neuroprotective/neurotoxic compounds reported in the CHEMBL database. The model predicts correctly >8300 experimental outcomes with Accuracy, Specificity, and Sensitivity above 80%–90% on training and external validation series. Indeed, the model can calculate different outcomes for >30 experimental measures in >400 different experimental protocolsin relation with >150 molecular and cellular targets on 11 different organisms (including human). Hereafter, we reported by the first time the synthesis, characterization, and experimental assays of a new series of chiral 1,2-rasagiline carbamate derivatives not reported in previous works. The experimental tests included: (1) assay in absence of neurotoxic agents; (2) in the presence of glutamate; and (3) in the presence of H2O2. Lastly, we used the new Assessing Links with Moving Averages (ALMA)-entropy model to predict possible outcomes for the new compounds in a high number of pharmacological tests not carried out experimentally. PMID:25255029

Measured effects of coolant injection on the performance of a film cooled turbine

NASA Technical Reports Server (NTRS)

Mcdonel, J. D.; Eiswerth, J. E.

1977-01-01

Tests have been conducted on a 20-inch diameter single-stage air-cooled turbine designed to evaluate the effects of film cooling air on turbine aerodynamic performance. The present paper reports the results of five test configurations, including two different cooling designs and three combinations of cooled and solid airfoils. A comparison is made of the experimental results with a previously published analytical method of evaluating coolant injection effects on turbine performance.

A Modified Constant-Stress Coupon for Enhanced Natural Crack Start during Fatigue Testing

DTIC Science & Technology

2016-05-01

improved numerically controlled manufacture. DSTO Research Report DSTO-RR-0340, July 2009. Wescott R, M Jones, M Heller. Stress analysis for design of...has been confirmed by Yu et al. (2014) through experimental strain measurement as well as fatigue tests under spectrum loading. However, as designed ...the results of analyses of a variety of typical non -optimal non -constant stress dog-bone coupon designs . One of those designs has in fact previously

Modeling of boron species in the Falcon 17 and ISP-34 integral tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lazaridis, M.; Capitao, J.A.; Drossinos, Y.

1996-09-01

The RAFT computer code for aerosol formation and transport was modified to include boron species in its chemical database. The modification was necessary to calculate fission product transport and deposition in the FAL-17 and ISP-34 Falcon tests, where boric acid was injected. The experimental results suggest that the transport of cesium is modified in the presence of boron. The results obtained with the modified RAFT code are presented; they show good agreement with experimental results for cesium and partial agreement for boron deposition in the Falcon silica tube. The new version of the RAFT code predicts the same behavior formore » iodine deposition as the previous version, where boron species were not included.« less

KSC-02pd0029

NASA Image and Video Library

2002-01-17

KENNEDY SPACE CENTER, FLA. -- Workers in the Vertical Processing Facility test the Near Infrared Camera and Multi-Object Spectrometer (NICMOS) Cooling System, part of the payload on mission STS-109, the Hubble Servicing Telescope Mission. The worker at right is using a black light. NICMOS II is a new experimental cooling system consisting of a compressor and tiny turbines. With the experimental cryogenic system, NASA hopes to re-cool the infrared detectors to below -315 degrees F (-193 degrees Celsius). NICMOS II was previously tested aboard STS-95 in 1998. It could extend the life of the Hubble Space Telescope by several years. Astronauts aboard Columbia on mission STS-109 will be replacing the original NICMOS with the newer version. Launch of mission STS-109 is scheduled for Feb. 28, 2002

Fault-tolerant Greenberger-Horne-Zeilinger paradox based on non-Abelian anyons.

PubMed

Deng, Dong-Ling; Wu, Chunfeng; Chen, Jing-Ling; Oh, C H

2010-08-06

We propose a scheme to test the Greenberger-Horne-Zeilinger paradox based on braidings of non-Abelian anyons, which are exotic quasiparticle excitations of topological states of matter. Because topological ordered states are robust against local perturbations, this scheme is in some sense "fault-tolerant" and might close the detection inefficiency loophole problem in previous experimental tests of the Greenberger-Horne-Zeilinger paradox. In turn, the construction of the Greenberger-Horne-Zeilinger paradox reveals the nonlocal property of non-Abelian anyons. Our results indicate that the non-Abelian fractional statistics is a pure quantum effect and cannot be described by local realistic theories. Finally, we present a possible experimental implementation of the scheme based on the anyonic interferometry technologies.

Theory of mind in dogs?: examining method and concept.

PubMed

Horowitz, Alexandra

2011-12-01

In line with other research, Udell, Dorey, and Wynne's (in press) finding that dogs and wolves pass on some trials of a putative theory-of-mind test and fail on others is as informative about the methods and concepts of the research as about the subjects. This commentary expands on these points. The intertrial differences in the target article demonstrate how critical the choice of cues is in experimental design; the intersubject-group differences demonstrate how life histories can interact with experimental design. Even the best-designed theory-of-mind tests have intractable logical problems. Finally, these and previous research results call for the introduction of an intermediate stage of ability, a rudimentary theory of mind, to describe subjects' performance.

A transient laboratory method for determining the hydraulic properties of 'tight' rocks-I. Theory

USGS Publications Warehouse

Hsieh, P.A.; Tracy, J.V.; Neuzil, C.E.; Bredehoeft, J.D.; Silliman, Stephen E.

1981-01-01

Transient pulse testing has been employed increasingly in the laboratory to measure the hydraulic properties of rock samples with low permeability. Several investigators have proposed a mathematical model in terms of an initial-boundary value problem to describe fluid flow in a transient pulse test. However, the solution of this problem has not been available. In analyzing data from the transient pulse test, previous investigators have either employed analytical solutions that are derived with the use of additional, restrictive assumptions, or have resorted to numerical methods. In Part I of this paper, a general, analytical solution for the transient pulse test is presented. This solution is graphically illustrated by plots of dimensionless variables for several cases of interest. The solution is shown to contain, as limiting cases, the more restrictive analytical solutions that the previous investigators have derived. A method of computing both the permeability and specific storage of the test sample from experimental data will be presented in Part II. ?? 1981.

Building Knowledge Structures by Testing Helps Children With Mathematical Learning Difficulty.

PubMed

Zhang, Yiyun; Zhou, Xinlin

2016-01-01

Mathematical learning difficulty (MLD) is prevalent in the development of mathematical abilities. Previous interventions for children with MLD have focused on number sense or basic mathematical skills. This study investigated whether mathematical performance of fifth grade children with MLD could be improved by developing knowledge structures by testing using a web-based curriculum learning system. A total of 142 children with MLD were recruited; half of the children were in the experimental group (using the system), and the other half were in the control group (not using the system). The children were encouraged to use the web-based learning system at home for at least a 15-min session, at least once a week, for one and a half months. The mean accumulated time of testing on the system for children in the experimental group was 56.2 min. Children in the experimental group had significantly higher scores on their final mathematical examination compared to the control group. The results suggest that web-based curriculum learning through testing that promotes the building of knowledge structures for a mathematical course was helpful for children with MLD. © Hammill Institute on Disabilities 2014.

Statistical model specification and power: recommendations on the use of test-qualified pooling in analysis of experimental data

PubMed Central

Colegrave, Nick

2017-01-01

A common approach to the analysis of experimental data across much of the biological sciences is test-qualified pooling. Here non-significant terms are dropped from a statistical model, effectively pooling the variation associated with each removed term with the error term used to test hypotheses (or estimate effect sizes). This pooling is only carried out if statistical testing on the basis of applying that data to a previous more complicated model provides motivation for this model simplification; hence the pooling is test-qualified. In pooling, the researcher increases the degrees of freedom of the error term with the aim of increasing statistical power to test their hypotheses of interest. Despite this approach being widely adopted and explicitly recommended by some of the most widely cited statistical textbooks aimed at biologists, here we argue that (except in highly specialized circumstances that we can identify) the hoped-for improvement in statistical power will be small or non-existent, and there is likely to be much reduced reliability of the statistical procedures through deviation of type I error rates from nominal levels. We thus call for greatly reduced use of test-qualified pooling across experimental biology, more careful justification of any use that continues, and a different philosophy for initial selection of statistical models in the light of this change in procedure. PMID:28330912

Time series modeling of human operator dynamics in manual control tasks

NASA Technical Reports Server (NTRS)

Biezad, D. J.; Schmidt, D. K.

1984-01-01

A time-series technique is presented for identifying the dynamic characteristics of the human operator in manual control tasks from relatively short records of experimental data. Control of system excitation signals used in the identification is not required. The approach is a multi-channel identification technique for modeling multi-input/multi-output situations. The method presented includes statistical tests for validity, is designed for digital computation, and yields estimates for the frequency responses of the human operator. A comprehensive relative power analysis may also be performed for validated models. This method is applied to several sets of experimental data; the results are discussed and shown to compare favorably with previous research findings. New results are also presented for a multi-input task that has not been previously modeled to demonstrate the strengths of the method.

Time Series Modeling of Human Operator Dynamics in Manual Control Tasks

NASA Technical Reports Server (NTRS)

Biezad, D. J.; Schmidt, D. K.

1984-01-01

A time-series technique is presented for identifying the dynamic characteristics of the human operator in manual control tasks from relatively short records of experimental data. Control of system excitation signals used in the identification is not required. The approach is a multi-channel identification technique for modeling multi-input/multi-output situations. The method presented includes statistical tests for validity, is designed for digital computation, and yields estimates for the frequency response of the human operator. A comprehensive relative power analysis may also be performed for validated models. This method is applied to several sets of experimental data; the results are discussed and shown to compare favorably with previous research findings. New results are also presented for a multi-input task that was previously modeled to demonstrate the strengths of the method.

Comparison of a quasi-3D analysis and experimental performance for three compact radial turbines

NASA Technical Reports Server (NTRS)

Simonyi, P. S.; Boyle, R. J.

1991-01-01

An experimental aerodynamic evaluation of three compact radial turbine builds was performed. Two rotors which were 40-50 percent shorter in axial length than conventional state-of-the-art radial rotors were tested. A single nozzle design was used. One rotor was tested with the nozzle at two stagger angle settings. A second rotor was tested with the nozzle in only the closed down setting. Experimental results were compared to predicted results from a quasi-3D inviscid and boundary layer analysis, called MTSB (Meridl/Tsonic/Blayer). This analysis was used to predict turbine performance. It has previously been calibrated only for axial, not radial, turbomachinery. The predicted and measured efficiencies were compared at the design point for the three turbines. At the design points the analysis overpredicted the efficiency by less than 1.7 points. Comparisons were also made at off-design operating points. The results of these comparisons showed the importance of an accurate clearance model for efficiency predictions and also that there are deficiencies in the incidence loss model used.

Comparison of a quasi-3D analysis and experimental performance for three compact radial turbines

NASA Technical Reports Server (NTRS)

Simonyi, P. S.; Boyle, R. J.

1991-01-01

An experimental aerodynamic evaluation of three compact radial turbine builds was performed. Two rotors which were 40 to 50 percent shorter in axial length than conventional state of the art radial rotors were tested. A single nozzle design was used. One rotor was tested with the nozzle at two stagger angle settings. A second rotor was tested with the nozzle in only the closed down setting. Experimental results were compared to predict results from a quasi-3D inviscid and boundary layer analysis, called Meridl/Tsonic/Blayer (MTSB). This analysis was used to predict turbine performance. It has previously been calibrated only for axial, not radial, turbomachinery. The predicted and measured efficiencies were compared at the design point for the three turbines. At the design points the analysis overpredicted the efficiency by less than 1.7 points. Comparisons were also made at off-design operating points. The results of these comparisons showed the importance of an accurate clearance model for efficiency predictions and also that there are deficiencies in the incidence loss model used.

Structural characterization of a first-generation articulated-truss joint for space crane application

NASA Technical Reports Server (NTRS)

Sutter, Thomas R.; Wu, K. Chauncey; Riutort, Kevin T.; Laufer, Joseph B.; Phelps, James E.

1992-01-01

A first-generation space crane articulated-truss joint was statically and dynamically characterized in a configuration that approximated an operational environment. The articulated-truss joint was integrated into a test-bed for structural characterization. Static characterization was performed by applying known loads and measuring the corresponding deflections to obtain load-deflection curves. Dynamic characterization was performed using modal testing to experimentally determine the first six mode shapes, frequencies, and modal damping values. Static and dynamic characteristics were also determined for a reference truss that served as a characterization baseline. Load-deflection curves and experimental frequency response functions are presented for the reference truss and the articulated-truss joint mounted in the test-bed. The static and dynamic experimental results are compared with analytical predictions obtained from finite element analyses. Load-deflection response is also presented for one of the linear actuators used in the articulated-truss joint. Finally, an assessment is presented for the predictability of the truss hardware used in the reference truss and articulated-truss joint based upon hardware stiffness properties that were previously obtained during the Precision Segmented Reflector (PSR) Technology Development Program.

Nubia's mother: being pregnant in the time of experimental vaccines and therapeutics for Ebola.

PubMed

Caluwaerts, Séverine

2017-12-14

During the 2014-2016 Ebola epidemic, Médecins Sans Frontières (MSF) treated Ebola-positive pregnant women in its Ebola Treatment Centers (ETCs). For pregnant women with confirmed Ebola virus disease, inclusion in clinical vaccine/drug/therapeutic trials was complicated. Despite their extremely high Ebola-related mortality in previous epidemics (89-93%) and a neonatal mortality of 100%, theoretical concerns about safety of vaccines and therapeutics in pregnancy were invoked, limiting pregnant women's access to an experimental live attenuated vaccine and brincidofovir, an experimental antiviral. Favipiravir, another experimental antiviral, was made available to pregnant women only after extensive negotiations and under a 'Monitored Emergency Use of Unregistered and Experimental Interventions' (MEURI) protocol. This paper describes the case of a pregnant woman who presented to the ETCs near the end of the Ebola epidemic in Guinea. The pregnant patient was admitted with confirmed Ebola disease. She was previously denied access to potentially protective vaccination due to pregnancy, and access to experimental ZMapp was only possible through a randomized clinical trial (presenting a 50% chance of not receiving ZMapp). She received favipiravir, but died of Ebola-related complications. The infant, born in the ETC, tested positive for Ebola at birth. The infant received ZMapp (under MEURI access outside of the clinical trial), an experimental drug GS5734, and a buffy coat of an Ebola survivor, and survived. Though the infant did have access to experimental therapeutics within 24 h of birth, access to other experimental compounds for her mother was denied, raising serious ethical concerns.

Experimental Investigation of Water Droplet Impingement on Airfoils, Finite Wings, and an S-duct Engine Inlet

NASA Technical Reports Server (NTRS)

Papadakis, Michael; Hung, Kuohsing E.; Vu, Giao T.; Yeong, Hsiung Wei; Bidwell, Colin S.; Breer, Martin D.; Bencic, Timothy J.

2002-01-01

Validation of trajectory computer codes, for icing analysis, requires experimental water droplet impingement data for a wide range of aircraft geometries as well as flow and icing conditions. This report presents improved experimental and data reduction methods for obtaining water droplet impingement data and provides a comprehensive water droplet impingement database for a range of test geometries including an MS(1)-0317 airfoil, a GLC-305 airfoil, an NACA 65(sub 2)-415 airfoil, a commercial transport tail section, a 36-inch chord natural laminar flow NLF(1)-0414 airfoil, a 48-inch NLF(1)-0414 section with a 25 percent chord simple flap, a state-of-the-art three-element high lift system, a NACA 64A008 finite span swept business jet tail, a full-scale business jet horizontal tail section, a 25 percent-scale business jet empennage, and an S-duct turboprop engine inlet. The experimental results were obtained at the NASA Glenn Icing Research Tunnel (IRT) for spray clouds with median volumetric diameter (MVD) of 11, 11.5, 21, 92, and 94 microns and for a range of angles of attack. The majority of the impingement experiments were conducted at an air speed of 175 mph corresponding to a Reynolds number of approximately 1.6 million per foot. The maximum difference of repeated tests from the average ranged from 0.24 to 12 percent for most of the experimental results presented. This represents a significant improvement in test repeatability compared to previous experimental studies. The increase in test repeatability was attributed to improvements made to the experimental and data reduction methods. Computations performed with the LEWICE-2D and LEWICE-3D computer codes for all test configurations are presented in this report. For the test cases involving median volumetric diameters of 11 and 21 microns, the correlation between the analytical and experimental impingement efficiency distributions was good. For the median volumetric diameters of 92 and 94-micron cases, however, the analysis produced higher impingement efficiencies and larger impingement limits than the experiment. It is speculated that this discrepancy is due to droplet splashing and breakup experienced by large droplets during impingement.

Neutronic experiments with fluorine rich compounds at LR-0 reactor

DOE PAGES

Losa, Evzen; Kostal, Michal; Czakoj, T.; ...

2018-06-06

Here, research on molten salt reactor (MSR) neutronics continues in Research Centre Rez (Czech Republic) with experimental work being conducted using fluoride salt that was originally used in the Molten Salt Reactor Experiment (MSRE). Previous results identified significant variations in the neutron spectrum measured in LiF-NaF salt. These variations could originate from the fluorine description in current nuclear data sets. Subsequent experiments were performed to try to confirm this phenomenon. Therefore, another fluorine-rich compound, Teflon, was used for testing. Critical experiments showed slight discrepancies in C/E-1 for both compounds, Teflon and FLIBE, and systematic overestimation of criticality was observed inmore » calculations. Different nuclear data libraries were used for data set testing. For Teflon, the overestimation is higher when using JENDL-3.3, JENDL-4, and RUSFOND-2010 libraries, all three of which share the same inelastic-to-elastic scattering cross section ratio. Calculations using other libraries (ENDF/B-VII.1, ENDF/B-VII.0, JEFF-3.2, JEFF-3.1, and CENDL-3.1) tend to be closer to the experimental value. Neutron spectrum measurement in both substances revealed structure similar to that seen in previous measurements using LiF-NaF salt, which indicates that the neutron spectrum seems to be strongly shaped by fluorine. Discrepancies between experimental and calculational results seem to be larger in the neutron energy range of 100–1300 keV than in higher energies. In the case of neutron spectrum calculation, none of the tested libraries gives overall better results than the others.« less

Neutronic experiments with fluorine rich compounds at LR-0 reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Losa, Evzen; Kostal, Michal; Czakoj, T.

Here, research on molten salt reactor (MSR) neutronics continues in Research Centre Rez (Czech Republic) with experimental work being conducted using fluoride salt that was originally used in the Molten Salt Reactor Experiment (MSRE). Previous results identified significant variations in the neutron spectrum measured in LiF-NaF salt. These variations could originate from the fluorine description in current nuclear data sets. Subsequent experiments were performed to try to confirm this phenomenon. Therefore, another fluorine-rich compound, Teflon, was used for testing. Critical experiments showed slight discrepancies in C/E-1 for both compounds, Teflon and FLIBE, and systematic overestimation of criticality was observed inmore » calculations. Different nuclear data libraries were used for data set testing. For Teflon, the overestimation is higher when using JENDL-3.3, JENDL-4, and RUSFOND-2010 libraries, all three of which share the same inelastic-to-elastic scattering cross section ratio. Calculations using other libraries (ENDF/B-VII.1, ENDF/B-VII.0, JEFF-3.2, JEFF-3.1, and CENDL-3.1) tend to be closer to the experimental value. Neutron spectrum measurement in both substances revealed structure similar to that seen in previous measurements using LiF-NaF salt, which indicates that the neutron spectrum seems to be strongly shaped by fluorine. Discrepancies between experimental and calculational results seem to be larger in the neutron energy range of 100–1300 keV than in higher energies. In the case of neutron spectrum calculation, none of the tested libraries gives overall better results than the others.« less

Treatment of experimental extravasation of amrubicin, liposomal doxorubicin, and mitoxantrone with dexrazoxane.

PubMed

Langer, Seppo W; Thougaard, Annemette V; Sehested, Maxwell; Jensen, Peter Buhl

2012-02-01

Dexrazoxane is an established treatment option in extravasation of the classic anthracyclines such as doxorubicin, epirubicin, and daunorubicin. However, it is not known whether the protection against the devastating tissue injuries extends into extravasation with new types of anthracyclines, the anthracenediones, or the liposomal pegylated anthracycline formulations. We therefore tested the antidotal efficacy of dexrazoxane against extravasation of amrubicin, mitoxantrone, and liposomal pegylated doxorubicin in mice. A total of 80 female B6D2F1 mice were tested in an established mouse extravasation model. The mice had experimental extravasations of amrubicin, mitoxtanrone, and Caelyx and were immediately hereafter treated with systemic dexrazoxane or saline. Systemic treatment with dexrazoxane resulted in significant protection against extravasation injuries from all three drugs. Moreover, the vesicant potential of the three test drugs was weaker than seen in previous experiments with the classic anthracyclines.

Predicted Sensitivity for Tests of Short-range Gravity with a Novel Parallel-plate Torsion Pendulum

NASA Astrophysics Data System (ADS)

Richards, Matthew; Baxley, Brandon; Hoyle, C. D.; Leopardi, Holly; Shook, David

2011-11-01

The parallel-plate torsion pendulum apparatus at Humboldt State University is designed to test the Weak Equivalence Principle (WEP) and the gravitational inverse-square law (ISL) of General Relativity at unprecedented levels in the sub-millimeter regime. Some versions of String Theory predict additional dimensions that might affect the gravitational inverse-square law (ISL) at sub-millimeter levels. Some models also predict the existence of unobserved subatomic particles, which if exist, could cause a violation in the WEP at short distances. Short-range tests of gravity and the WEP are also instrumental in investigating possible proposed mechanisms that attempt to explain the accelerated expansion of the universe, generally attributed to Dark Energy. The weakness of the gravitational force makes measurement very difficult at small scales. Testing such a minimal force requires highly isolated experimental systems and precise measurement and control instrumentation. Moreover, a dedicated test of the WEP has not been performed below the millimeter scale. This talk will discuss the improved sensitivity that we expect to achieve in short-range gravity tests with respect to previous efforts that employ different experimental configurations.

Comparative evaluation of Bacopa monniera and Panax quniquefolium in experimental anxiety and depressive models in mice.

PubMed

Chatterjee, Manavi; Verma, Pinki; Palit, Gautam

2010-03-01

The present study was undertaken to compare medicinal plants against mixed anxiety-depressive disorder (MAD) to evaluate their potency in combating MAD disorders. Previous studies from our lab have shown that Bacopa monniera (BM), and Panax quniquefolium (PQ) have significant adaptogenic properties. Hence, we have further confirmed their activity in stress related disorders like anxiety and depression in animal model, rodents and assessed their efficacy. In our experimental protocol, gross behaviour was observed through Digiscan animal activity monitor. Anxiety was studied through light dark test, elevated plus maze test and holeboard test. Depression experiments were conducted following tail suspension test and forced swim test. Further, rotarod test was also used to study any defects in motor in-coordination in mice. It was observed that BM at the dose of 80 mg/kg (po) and PQ at 100 mg/kg (po) were effective as an anti-anxiety as well anti-depressant activity and had no motor in-coordination in mice. Hence, these extracts can be used as a potent therapeutic agent in treating mixed anxiety-depressive disorder (MAD).

Torso-Tank Validation of High-Resolution Electrogastrography (EGG): Forward Modelling, Methodology and Results.

PubMed

Calder, Stefan; O'Grady, Greg; Cheng, Leo K; Du, Peng

2018-04-27

Electrogastrography (EGG) is a non-invasive method for measuring gastric electrical activity. Recent simulation studies have attempted to extend the current clinical utility of the EGG, in particular by providing a theoretical framework for distinguishing specific gastric slow wave dysrhythmias. In this paper we implement an experimental setup called a 'torso-tank' with the aim of expanding and experimentally validating these previous simulations. The torso-tank was developed using an adult male torso phantom with 190 electrodes embedded throughout the torso. The gastric slow waves were reproduced using an artificial current source capable of producing 3D electrical fields. Multiple gastric dysrhythmias were reproduced based on high-resolution mapping data from cases of human gastric dysfunction (gastric re-entry, conduction blocks and ectopic pacemakers) in addition to normal test data. Each case was recorded and compared to the previously-presented simulated results. Qualitative and quantitative analyses were performed to define the accuracy showing [Formula: see text] 1.8% difference, [Formula: see text] 0.99 correlation, and [Formula: see text] 0.04 normalised RMS error between experimental and simulated findings. These results reaffirm previous findings and these methods in unison therefore present a promising morphological-based methodology for advancing the understanding and clinical applications of EGG.

Social learning in nest-building birds watching live-streaming video demonstrators.

PubMed

Guillette, Lauren M; Healy, Susan D

2018-02-13

Determining the role that social learning plays in construction behaviours, such as nest building or tool manufacture, could be improved if more experimental control could be gained over the exact public information that is provided by the demonstrator, to the observing individual. Using video playback allows the experimenter to choose what information is provided, but will only be useful in determining the role of social learning if observers attend to, and learn from, videos in a manner that is similar to live demonstration. The goal of the current experiment was to test whether live-streamed video presentations of nest building by zebra finches Taeniopygia guttata would lead observers to copy the material choice demonstrated to them. Here, males that had not previously built a nest were given an initial preference test between materials of two colours. Those observers then watched live-stream footage of a familiar demonstrator building a nest with material of the colour that the observer did not prefer. After this experience, observers were given the chance to build a nest with materials of the two colours. Although two-thirds of the observer males preferred material of the demonstrated colour after viewing the demonstrator build a nest with material of that colour more than they had previously, their preference for the demonstrated material was not as strong as that of observers that had viewed live demonstrator builders in a previous experiment. Our results suggest researchers should proceed with caution before using video demonstration in tests of social learning. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

[The Effect of Structured Group Reminiscence Therapy on the Life Satisfaction of Institutionalized Elderly].

PubMed

Chen, Shu-Mei; Kuo, Chien-Lin; Chen, Mei-Rong; Lee, Lai-Ling; Lee, Pi-Yueh; Wang, Shu-Fen

2016-08-01

Long-term care institutions have become an option for older people who are dependent in daily living. However, insufficient attention has been focused on assessing the life satisfaction of those currently residing in these institutions in Taiwan. Previous research indicates that group reminiscence may improve the life satisfaction of older adults. However, there is currently no consensus regarding the implementation and evaluation of reminiscence interventions. To examine the effect of a structured group reminiscence protocol on the life satisfaction of institutionalized older adults. The study used a quasi-experimental design. A total of 48 older adults were conveniently recruited from two long-term care institutions in southern Taiwan. The experimental group (n = 23) received 8 weeks of structured-group reminiscence for 40 minutes weekly, while the control group (n = 25) received routine care from the institution. Both groups were evaluated using a life-satisfaction questionnaire before and after the intervention and again four weeks later. Life satisfaction scores were statistically similar on the pre-test and significantly different on both post-test questionnaires for the two groups. The scores for the experimental and control groups were pre-test: 24.22 vs 23.36 (p = .063); post-test I: 27.22 vs 23.32 (p < .001); and post-test II: 26.43 vs 23.00 (p < .001). The mean post-test scores for the experimental group were significantly higher than the pre-test score (p < .001). The generalized estimating equation test showed that the overall score of life satisfaction for the experimental group increased by 0.85-points (p = .042) more than the control group, which is a significant difference. The results support that the 8-week structured group reminiscence protocol effectively enhances life satisfaction in older adults. The results of this study may be referenced in the continuing education of nurses working in long-term care institutions in the context of helping nurses organize, facilitate, and evaluate this protocol.

The Effect of Labeling on Preschool Children's Performance in the Dimensional Change Card Sort Task

ERIC Educational Resources Information Center

Muller, Ulrich; Zelazo, Philip D.; Lurye, Leah E.; Liebermann, Dana P.

2008-01-01

Previous research suggests that experimenter-induced labeling of test cards improves preschoolers' performance on the Dimensional Change Card Sort Task (DCCS), a measure of flexible rule use. Three experiments attempted to further clarify how labeling aids performance on the DCCS. Experiment 1 examined the nature of the labeling effect but failed…

Testing a Violence-Prevention Intervention for Incarcerated Women Using a Randomized Control Trial

ERIC Educational Resources Information Center

Kubiak, Sheryl Pimlott; Kim, Woo Jong; Fedock, Gina; Bybee, Deborah

2015-01-01

Objective: Beyond Violence (BV), a new prevention program for women with assaultive offenses, demonstrated feasibility in previous studies. This study's purpose is to assess the efficacy of BV using a randomized control trial. Method: Eligible women were randomly assigned to treatment as usual (TAU) and the experimental condition (BV). Measures of…

A high throughput transformation system allows the regeneration of marker-free plum plants (Prunus domestica L.)

USDA-ARS?s Scientific Manuscript database

A high-throughput transformation system previously developed in our laboratory was used for the regeneration of transgenic plum plants without the use of antibiotic selection. The system was first tested with two experimental constructs, pGA482GGi and pCAMBIAgfp94(35S), that contain selective marke...

Learning Arithmetic Outdoors in Junior High School--Influence on Performance and Self-Regulating Skills

ERIC Educational Resources Information Center

Fägerstam, Emilia; Samuelsson, Joakim

2014-01-01

This study aims to explore the influence of outdoor teaching among students, aged 13, on arithmetic performance and self-regulation skills as previous research concerning outdoor mathematics learning is limited. This study had a quasi-experimental design. An outdoor and a traditional group answered a test and a self-regulation skills questionnaire…

A kinesthetic-tactual display for stall deterrence

NASA Technical Reports Server (NTRS)

Gilson, R. D.; Ventola, R. W.; Fenton, R. E.

1975-01-01

A kinesthetic tactual display may be effectively used as a control aid per previous flight tests. Angle of attack information would be continuously presented to a pilot, via this display, during critical operational phases where stalls are probable. A two phase plan for evaluating this concept is presented. A first development phase would encompass: (1) display fabrication for a conventional control yoke; (2) its installation, together with other necessary instrumentation, in an experimental aircraft; and (3) preliminary flight testing by experienced pilots.

Comparison of NASA and contractor results from aeroacoustic tests of QCSEE OTW engine

NASA Technical Reports Server (NTRS)

Bloomer, H. E.; Loeffler, I. J.; Kreim, W. J.; Coats, J. W.

1981-01-01

The aerodynamics and acoustics of the over-the-wing (OTW) Quiet, Clean, Short Haul Experimental Engine (QCSEE) were tested. A boilerplate (nonflight weight), high-throat Mach number, acoustically treated inlet and a D-shaped OTW exhaust nozzle with variable position side doors were used. Some acoustic directivity results for the type "D" nozzle and acoustic effects of variations in the nozzle side door positions are included. It was found that the results are in agreement with those previously obtained.

Improved Healing of Large, Osseous, Segmental Defects by Reverse Dynamization: Evaluation in a Sheep Model

DTIC Science & Technology

2014-10-01

initiated. One such fixator has been tested on a cadaveric sheep tibia. In the unlocked, loose position, the axial stiffness of the tibia and fixator...suggested by our previous studies using rats. This aspect of the project is the present focus of attention, and additional cadaver legs will be tested...characterize external fixators). A 3 mm tibial defect was created in the leg of a cadaveric sheep, and stabilized with an experimental external

An experimental approach in revisiting the magnetic orientation of cattle

PubMed Central

Weijers, Debby; Hemerik, Lia; Heitkönig, Ignas M. A.

2018-01-01

In response to the increasing number of observational studies on an apparent south-north orientation in non-homing, non-migrating terrestrial mammals, we experimentally tested the alignment hypothesis using strong neodymium magnets on the resting orientation of individual cattle in Portugal. Contrary to the hypothesis, the 34 cows in the experiment showed no directional preference, neither with, nor without a strong neodymium magnet fixed to their collar. The concurrently performed 2,428 daytime observations—excluding the hottest part of the day—of 659 resting individual cattle did not show a south-north alignment when at rest either. The preferred compass orientation of these cows was on average 130 degrees from the magnetic north (i.e., south east). Cow compass orientation correlated significantly with sun direction, but not with wind direction. In as far as we can determine, this is the first experimental test on magnetic orientation in larger, non-homing, non-migrating mammals. These experimental and observational findings do not support previously published suggestions on the magnetic south-north alignment in these mammals. PMID:29641517

Arc Jet Facility Test Condition Predictions Using the ADSI Code

NASA Technical Reports Server (NTRS)

Palmer, Grant; Prabhu, Dinesh; Terrazas-Salinas, Imelda

2015-01-01

The Aerothermal Design Space Interpolation (ADSI) tool is used to interpolate databases of previously computed computational fluid dynamic solutions for test articles in a NASA Ames arc jet facility. The arc jet databases are generated using an Navier-Stokes flow solver using previously determined best practices. The arc jet mass flow rates and arc currents used to discretize the database are chosen to span the operating conditions possible in the arc jet, and are based on previous arc jet experimental conditions where possible. The ADSI code is a database interpolation, manipulation, and examination tool that can be used to estimate the stagnation point pressure and heating rate for user-specified values of arc jet mass flow rate and arc current. The interpolation is performed in the other direction (predicting mass flow and current to achieve a desired stagnation point pressure and heating rate). ADSI is also used to generate 2-D response surfaces of stagnation point pressure and heating rate as a function of mass flow rate and arc current (or vice versa). Arc jet test data is used to assess the predictive capability of the ADSI code.

High-Speed Research: 1994 Sonic Boom Workshop. Configuration, Design, Analysis and Testing

NASA Technical Reports Server (NTRS)

McCurdy, David A. (Editor)

1999-01-01

The third High-Speed Research Sonic Boom Workshop was held at NASA Langley Research Center on June 1-3, 1994. The purpose of this workshop was to provide a forum for Government, industry, and university participants to present and discuss progress in their research. The workshop was organized into sessions dealing with atmospheric propagation; acceptability studies; and configuration design, and testing. Attendance at the workshop was by invitation only. The workshop proceedings include papers on design, analysis, and testing of low-boom high-speed civil transport configurations and experimental techniques for measuring sonic booms. Significant progress is noted in these areas in the time since the previous workshop a year earlier. The papers include preliminary results of sonic boom wind tunnel tests conducted during 1993 and 1994 on several low-boom designs. Results of a mission performance analysis of all low-boom designs are also included. Two experimental methods for measuring near-field signatures of airplanes in flight are reported.

Tracer adsorption in sand-tank experiments of saltwater up-coning

NASA Astrophysics Data System (ADS)

Jakovovic, Danica; Post, Vincent E. A.; Werner, Adrian D.; Männicke, Oliver; Hutson, John L.; Simmons, Craig T.

2012-01-01

SummaryThis study aims to substantiate otherwise unresolved double-peaked plumes produced in recent saltwater up-coning experiments (see Jakovovic et al. (2011), Numerical modelling of saltwater up-coning: Comparison with experimental laboratory observations, Journal of Hydrology 402, 261-273) through additional laboratory testing and numerical modelling. Laboratory experimentation successfully reproduced the double-peaked plume demonstrating that this phenomenon was not an experimental nuance in previous experiments. Numerical modelling by Jakovovic et al. (2011) was extended by considering adsorption effects, which were needed to explain the observed up-coning double peaks of both previous and current laboratory experiments. A linear adsorption isotherm was applied in predicting dye tracer (Rhodamine WT) behaviour in the sand-tank experiments using adsorption parameters obtained experimentally. The same adsorption parameters were tested on all laboratory experiments and it was found that adsorption had insignificant effect on experiments with high pumping rates. However, low pumping rates produced pronounced spatial velocity variations within the dense salt plume beneath the pumping well, with velocities within the plume increasing from the centre of the plume towards the interface. The dye tracer was retarded relative to the salt and was transported preferentially along the higher-velocity paths (i.e. along the edges of the salt plume) towards the well forming double-peaked up-coning patterns. This illustrates the sensitive adsorptive nature of Rhodamine WT and that care should be taken when it is used in similar sand-tank experiments. Observations from this study offer insight into the separation of chemicals in natural systems due to different adsorption characteristics and under conditions of density-dependent flow.

Image recognition and consistency of response

NASA Astrophysics Data System (ADS)

Haygood, Tamara M.; Ryan, John; Liu, Qing Mary A.; Bassett, Roland; Brennan, Patrick C.

2012-02-01

Purpose: To investigate the connection between conscious recognition of an image previously encountered in an experimental setting and consistency of response to the experimental question.
Materials and Methods: Twenty-four radiologists viewed 40 frontal chest radiographs and gave their opinion as to the position of a central venous catheter. One-to-three days later they again viewed 40 frontal chest radiographs and again gave their opinion as to the position of the central venous catheter. Half of the radiographs in the second set were repeated images from the first set and half were new. The radiologists were asked of each image whether it had been included in the first set. For this study, we are evaluating only the 20 repeated images. We used the Kruskal-Wallis test and Fisher's exact test to determine the relationship between conscious recognition of a previously interpreted image and consistency in interpretation of the image.
Results. There was no significant correlation between recognition of the image and consistency in response regarding the position of the central venous catheter. In fact, there was a trend in the opposite direction, with radiologists being slightly more likely to give a consistent response with respect to images they did not recognize than with respect to those they did recognize.
Conclusion: Radiologists' recognition of previously-encountered images in an observer-performance study does not noticeably color their interpretation on the second encounter.

Expanded operational capabilities of the Langley Mach 7 Scramjet test facility

NASA Technical Reports Server (NTRS)

Thomas, S. R.; Guy, R. W.

1983-01-01

An experimental research program conducted to expand the operational capabilities of the NASA Langley Mach 7 Scramjet Test Facility is described. Previous scramjet testing in this facility was limited to a single simulated flight condition of Mach 6.9 at an altitude of 115,300 ft. The arc heater research demonstrates the potential of the facility for scramjet testing at simulated flight conditions from Mach 4 (at altitudes from 77,000 to 114,000 ft) to Mach 7 (at latitudes from 108,000 to 149,000 ft). Arc heater electrical characteristics, operational problems, measurements of nitrogen oxide contaminants, and total-temperature profiles are discussed.

Green-Kubo relation for viscosity tested using experimental data for a two-dimensional dusty plasma

NASA Astrophysics Data System (ADS)

Feng, Yan; Goree, J.; Liu, Bin; Cohen, E. G. D.

2011-10-01

The theoretical Green-Kubo relation for viscosity is tested using experimentally obtained data. In a dusty plasma experiment, micron-sized dust particles are introduced into a partially ionized argon plasma, where they become negatively charged. They are electrically levitated to form a single-layer Wigner crystal, which is subsequently melted using laser heating. In the liquid phase, these dust particles experience interparticle electric repulsion, laser heating, and friction from the ambient neutral argon gas, and they can be considered to be in a nonequilibrium steady state. Direct measurements of the positions and velocities of individual dust particles are then used to obtain a time series for an off-diagonal element of the stress tensor and its time autocorrelation function. This calculation also requires the interparticle potential, which was not measured experimentally but was obtained using a Debye-Hückel-type model with experimentally determined parameters. Integrating the autocorrelation function over time yields the viscosity for shearing motion among dust particles. The viscosity so obtained is found to agree with results from a previous experiment using a hydrodynamical Navier-Stokes equation. This comparison serves as a test of the Green-Kubo relation for viscosity. Our result is also compared to the predictions of several simulations.

Experimental and Theoretical Study of Heat Conduction for Air up to 5000 K

NASA Technical Reports Server (NTRS)

Peng, Tzy-Cheng; Ahtye, Warren F.

1961-01-01

The theoretical value of the integral of thermal conductivity is compared with the experimental values from shock-tube measurements. The particular case considered is the one-dimensional nonsteady flow of heat through air at constant pressure. This approach has been previously described in NASA TR R-27. experiment was uncertain because of the large scatter in the experimental data. In this paper, an attempt is made to improve the correlation by use of a more refined calculation of the integral of thermal conductivity, and by use of improved experimental techniques and instrumentation. As a result of these changes, a much closer correlation is shown between the experimental and theoretical heat-flux potentials. This indicates that the predicted values of the coefficient of thermal conductivity for high-temperature air may be suitably accurate for many engineering needs, up to the limits of the test (4600 K).

Social disappointment explains chimpanzees' behaviour in the inequity aversion task.

PubMed

Engelmann, Jan M; Clift, Jeremy B; Herrmann, Esther; Tomasello, Michael

2017-08-30

Chimpanzees' refusal of less-preferred food when an experimenter has previously provided preferred food to a conspecific has been taken as evidence for a sense of fairness. Here, we present a novel hypothesis-the social disappointment hypothesis-according to which food refusals express chimpanzees' disappointment in the human experimenter for not rewarding them as well as they could have. We tested this hypothesis using a two-by-two design in which food was either distributed by an experimenter or a machine and with a partner present or absent. We found that chimpanzees were more likely to reject food when it was distributed by an experimenter rather than by a machine and that they were not more likely to do so when a partner was present. These results suggest that chimpanzees' refusal of less-preferred food stems from social disappointment in the experimenter and not from a sense of fairness. © 2017 The Author(s).

Comparative analysis of international standards for the fatigue testing of posterior spinal fixation systems: the importance of preload in ISO 12189.

PubMed

La Barbera, Luigi; Ottardi, Claudia; Villa, Tomaso

2015-10-01

Preclinical evaluation of the mechanical reliability of fixation devices is a mandatory activity before their introduction into market. There are two standardized protocols for preclinical testing of spinal implants. The American Society for Testing Materials (ASTM) recommends the F1717 standard, which describes a vertebrectomy condition that is relatively simple to implement, whereas the International Organization for Standardization (ISO) suggests the 12189 standard, which describes a more complex physiological anterior support-based setup. Moreover, ASTM F1717 is nowadays well established, whereas ISO 12189 has received little attention: A few studies tried to accurately describe the ISO experimental procedure through numeric models, but these studies totally neglect the recommended precompression step. This study aimed to build up a reliable, validated numeric model capable of describing the stress on the rods of a spinal fixator assembled according to ISO 12189 standard procedure. Such a model would more adequately represent the in vitro testing condition. This study used finite element (FE) simulations and experimental validation testing. An FE model of the ISO setup was built to calculate the stress on the rods. Simulation was validated by comparison with experimental strain gauges measurements. The same fixator has been previously virtually mounted in an L2-L4 FE model of the lumbar spine, and stresses in the rods were calculated when the spine was subjected to physiological forces and moments. The comparison between the FE predictions and experimental measurements is in good agreement, thus confirming the suitability of the FE method to evaluate the stresses in the device. The initial precompression induces a significant extension of the assembled construct. As the applied load increases, the initial extension is gradually compensated, so that at peak load the rods are bent in flexion: The final stress value predicted is thus reduced to about 50%, if compared with the previous model where the precompression was not considered. Neglecting the initial preload due to the assembly of the overall construct according to ISO 12189 standard could lead to an overestimation of the stress on the rods up to 50%. To correctly describe the state of stress on the posterior spinal fixator, tested according to the ISO procedure, it is important to take into account the initial preload due to the assembly of the overall construct. Copyright © 2015 Elsevier Inc. All rights reserved.

Experimental aerodynamic performance of advanced 40 deg-swept 10-blade propeller model at Mach 0.6 to 0.85

NASA Technical Reports Server (NTRS)

Mitchell, Glenn A.

1988-01-01

A propeller designated as SR-6, designed with 40 deg of sweep and 10 blades to cruise at Mach 0.8 at an altitude of 10.7 km (35,000 ft), was tested in the NASA Lewis Research Center's 8- by 6-Foot Wind Tunnel. This propeller was one of a series of advanced single rotation propeller models designed and tested as part of the NASA Advanced Turboprop Project. Design-point net efficiency was almost constant to Mach 0.75 but fell above this speed more rapidly than that of any previously tested advanced propeller. Alternative spinners that further reduced the near-hub interblade Mach numbers and relieved the observed hub choking improved performance above Mach 0.75. One spinner attained estimated SR-6 Design-point net deficiencies of 80.6 percent at Mach 0.75 and 79.2 percent at Mach 0.8, higher than the measured performance of any previously tested advanced single-rotation propeller at these speeds.

Molecular engineering and measurements to test hypothesized mechanisms in single molecule conductance switching.

PubMed

Moore, Amanda M; Dameron, Arrelaine A; Mantooth, Brent A; Smith, Rachel K; Fuchs, Daniel J; Ciszek, Jacob W; Maya, Francisco; Yao, Yuxing; Tour, James M; Weiss, Paul S

2006-02-15

Six customized phenylene-ethynylene-based oligomers have been studied for their electronic properties using scanning tunneling microscopy to test hypothesized mechanisms of stochastic conductance switching. Previously suggested mechanisms include functional group reduction, functional group rotation, backbone ring rotation, neighboring molecule interactions, bond fluctuations, and hybridization changes. Here, we test these hypotheses experimentally by varying the molecular designs of the switches; the ability of the molecules to switch via each hypothetical mechanism is selectively engineered into or out of each molecule. We conclude that hybridization changes at the molecule-surface interface are responsible for the switching we observe.

Prediction of multi-target networks of neuroprotective compounds with entropy indices and synthesis, assay, and theoretical study of new asymmetric 1,2-rasagiline carbamates.

PubMed

Romero Durán, Francisco J; Alonso, Nerea; Caamaño, Olga; García-Mera, Xerardo; Yañez, Matilde; Prado-Prado, Francisco J; González-Díaz, Humberto

2014-09-24

In a multi-target complex network, the links (L(ij)) represent the interactions between the drug (d(i)) and the target (t(j)), characterized by different experimental measures (K(i), K(m), IC50, etc.) obtained in pharmacological assays under diverse boundary conditions (c(j)). In this work, we handle Shannon entropy measures for developing a model encompassing a multi-target network of neuroprotective/neurotoxic compounds reported in the CHEMBL database. The model predicts correctly >8300 experimental outcomes with Accuracy, Specificity, and Sensitivity above 80%-90% on training and external validation series. Indeed, the model can calculate different outcomes for >30 experimental measures in >400 different experimental protocolsin relation with >150 molecular and cellular targets on 11 different organisms (including human). Hereafter, we reported by the first time the synthesis, characterization, and experimental assays of a new series of chiral 1,2-rasagiline carbamate derivatives not reported in previous works. The experimental tests included: (1) assay in absence of neurotoxic agents; (2) in the presence of glutamate; and (3) in the presence of H2O2. Lastly, we used the new Assessing Links with Moving Averages (ALMA)-entropy model to predict possible outcomes for the new compounds in a high number of pharmacological tests not carried out experimentally.

Reversed-phase liquid chromatography column testing: robustness study of the test.

PubMed

Le Mapihan, K; Vial, J; Jardy, A

2004-12-24

Choosing the right RPLC column for an actual separation among the more than 600 commercially available ones still represents a real challenge for the analyst particularly when basic solutes are involved. Many tests dedicated to the characterization and the classification of stationary phases have been proposed in the literature and some of them highlighted the need of a better understanding of retention properties to lead to a rational choice of columns. However, unlike classical chromatographic methods, the problem of their robustness evaluation has often been left unaddressed. In the present study, we present a robustness study that was applied to the chromatographic testing procedure we had developed and optimized previously. A design of experiment (DoE) approach was implemented. Four factors, previously identified as potentially influent, were selected and subjected to small controlled variations: solvent fraction, temperature, pH and buffer concentration. As our model comprised quadratic terms instead of a simple linear model, we chose a D-optimal design in order to minimize the experiment number. As a previous batch-to-batch study [K. Le Mapihan, Caractérisation et classification des phases stationnaires utilisées pour l'analyse CPL de produits pharmaceutiques, Ph.D. Thesis, Pierre and Marie Curie University, 2004] had shown a low variability on the selected stationary phase, it was then possible to split the design into two parts, according to the solvent nature, each using one column. Actually, our testing procedure involving assays both with methanol and with acetonitrile as organic modifier, such an approach enabled to avoid a possible bias due to the column ageing considering the number of experiments required (16 + 6 center points). Experimental results were computed thanks to a Partial Least Squares regression procedure, more adapted than the classical regression to handle factors and responses not completely independent. The results showed the behavior of the solutes in relation to their physico-chemical properties and the relevance of the second term degree of our model. Finally, the robust domain of the test has been fairly identified, so that any potential user precisely knows to which extend each experimental parameter must be controlled when our testing procedure is to be implemented.

Quasi-experimental Effectiveness of Cognitive-behavioral Therapy on Reliving Migraine Headaches in Migraine Sufferers.

PubMed

Ebrahimi Moghadam, Hosein; Karimi, Ahoo; Seifi, Kimia

2017-01-01

This study aimed to investigate the effectiveness of cognitive-behavioral therapy on relieving migraine headaches in migraine sufferers. In this quasi-experimental study with pre-test and post-test method, the samples were outpatients of public hospitals in Ilam City, southwestern Iran since May-Jul 2010. They were selected based on inclusion and exclusion criteria, and divided into experimental and control groups. The data were analyzed using SPSS ver. 16 and via multivariate covariance method. Cognitive-behavioral therapy affected on reducing the duration of symptoms of migraine in sufferers ( P <0.05). Cognitive behavioral therapy effects on reducing the time duration of symptoms of migraine headaches. Thistherapeutic method increases the level of individual, familial, social and occupational activities by reducing the time duration of symptoms and this method helps the individuals to resume their activities and regain their previous control instead of founding themselves incapable and helpless due to the pain they suffer from.

X-38 Experimental Aeroheating at Mach 10

NASA Technical Reports Server (NTRS)

Berry, Scott A.; Horvath, Thomas J.; Weilmuenster, K. James; Alter, Stephan J.; Merski, N. Ronald

2001-01-01

This report provides an update of the hypersonic aerothermodynamic wind tunnel test program conducted at the NASA Langley Research Center in support of the X-38 program. Global surface heat transfer distributions were measured on 0.0177 and 0.0236 scale models of the proposed X-38 configuration at Mach 10 in air. The parametrics that were investigated primarily include freestream unit Reynolds numbers of 0.6 to 2.2 million per foot and body flap deflections of 15, 20, and 25 deg for an angle-of-attack of 40 deg. The model-scale variance was tested to obtain laminar, transitional, and turbulent heating levels on the defected bodyflaps. In addition, a limited investigation of forced boundary layer transition through the use of discrete roughness elements was performed. Comparisons of the present experimental results to computational predictions and previous experimental data were conducted Laminar, transitional, and turbulent heating levels were observed on the deflected body flap, which compared favorably to the computational results and to the predicted heating based on the flight aerothermodynamic database.

Preliminary experimental investigation of an X-band Cerenkov-type high power microwave oscillator without guiding magnetic field.

PubMed

Guo, Liming; Shu, Ting; Li, Zhiqiang; Ju, Jinchuan; Fang, Xiaoting

2017-02-01

Among high power microwave (HPM) generators without guiding magnetic field, Cerenkov-type oscillator is expected to achieve a relatively high efficiency, which has already been realized in X-band in our previous simulation work. This paper presents the preliminary experimental investigations into an X-band Cerenkov-type HPM oscillator without guiding magnetic field. Based on the previous simulation structure, some modifications regarding diode structure were made. Different cathode structures and materials were tested in the experiments. By using a ring-shaped graphite cathode, microwave of about one hundred megawatt level was generated with a pure center frequency of 9.14 GHz, and an efficiency of about 1.3%. As analyzed in the paper, some practical issues reduce the efficiency in experiments, such as real features of the electron beam, probable breakdown regions on the cathode surface which can damage the diode, and so forth.

LANL Skid Testing Summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dickson, Peter

2014-04-09

Our improved understanding of the processes occurring during complex drop / skid events has explained the previously observed scatter in skid and drop test data, and provided new insights into effective mitigation strategies. However, it has been perceived to undermine our current safety assumptions, which is inaccurate. We have no reason to believe that our safety margin from HEVR (the event of concern) is any different to that previously assumed – we just have a much better experimental and theoretical basis by which to measure it more accurately. Until this work is complete or, at least, more mature, we cannotmore » draw any conclusions on whether we are more or less safe than we thought, but we know that use of cushioned surfaces, along with sensible housekeeping, mitigates the potential activation of the skid-grit mechanism.« less

Uncertainty Analysis of Inertial Model Attitude Sensor Calibration and Application with a Recommended New Calibration Method

NASA Technical Reports Server (NTRS)

Tripp, John S.; Tcheng, Ping

1999-01-01

Statistical tools, previously developed for nonlinear least-squares estimation of multivariate sensor calibration parameters and the associated calibration uncertainty analysis, have been applied to single- and multiple-axis inertial model attitude sensors used in wind tunnel testing to measure angle of attack and roll angle. The analysis provides confidence and prediction intervals of calibrated sensor measurement uncertainty as functions of applied input pitch and roll angles. A comparative performance study of various experimental designs for inertial sensor calibration is presented along with corroborating experimental data. The importance of replicated calibrations over extended time periods has been emphasized; replication provides independent estimates of calibration precision and bias uncertainties, statistical tests for calibration or modeling bias uncertainty, and statistical tests for sensor parameter drift over time. A set of recommendations for a new standardized model attitude sensor calibration method and usage procedures is included. The statistical information provided by these procedures is necessary for the uncertainty analysis of aerospace test results now required by users of industrial wind tunnel test facilities.

Animal models for testing anti-prion drugs.

PubMed

Fernández-Borges, Natalia; Elezgarai, Saioa R; Eraña, Hasier; Castilla, Joaquín

2013-01-01

Prion diseases belong to a group of fatal infectious diseases with no effective therapies available. Throughout the last 35 years, less than 50 different drugs have been tested in different experimental animal models without hopeful results. An important limitation when searching for new drugs is the existence of appropriate models of the disease. The three different possible origins of prion diseases require the existence of different animal models for testing anti-prion compounds. Wild type, over-expressing transgenic mice and other more sophisticated animal models have been used to evaluate a diversity of compounds which some of them were previously tested in different in vitro experimental models. The complexity of prion diseases will require more pre-screening studies, reliable sporadic (or spontaneous) animal models and accurate chemical modifications of the selected compounds before having an effective therapy against human prion diseases. This review is intended to put on display the more relevant animal models that have been used in the search of new antiprion therapies and describe some possible procedures when handling chemical compounds presumed to have anti-prion activity prior to testing them in animal models.

Performance Evaluation of Advanced Retrofit Roof Technologies Using Field-Test Data Phase Three Final Report, Volume 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biswas, Kaushik; Childs, Phillip W.; Atchley, Jerald Allen

2015-01-01

This article presents some miscellaneous data from two low-slope and two steep-slope experimental roofs. The low-slope roofs were designed to compare the performance of various roof coatings exposed to natural weatherization. The steep-slope roofs contained different combinations of phase change material, rigid insulation, low emittance surface and above-sheathing ventilation, with standing-seam metal panels on top. The steep-slope roofs were constructed on a series of adjacent attics separated at the gables using thick foam insulation. This article describes phase three (3) of a study that began in 2009 to evaluate the energy benefits of a sustainable re-roofing technology utilizing standing-seam metalmore » roofing panels combined with energy efficient features like above-sheathing-ventilation (ASV), phase change material (PCM) and rigid insulation board. The data from phases 1 and 2 have been previously published and reported [Kosny et al., 2011; Biswas et al., 2011; Biswas and Childs, 2012; Kosny et al., 2012]. Based on previous data analyses and discussions within the research group, additional test roofs were installed in May 2012, to test new configurations and further investigate different components of the dynamic insulation systems. Some experimental data from phase 3 testing from May 2012 to December 2013 and some EnergyPlus modeling results have been reported in volumes 1 and 3, respectively, of the final report [Biswas et al., 2014; Biswas and Bhandari, 2014].« less

Statistical analysis and application of quasi experiments to antimicrobial resistance intervention studies.

PubMed

Shardell, Michelle; Harris, Anthony D; El-Kamary, Samer S; Furuno, Jon P; Miller, Ram R; Perencevich, Eli N

2007-10-01

Quasi-experimental study designs are frequently used to assess interventions that aim to limit the emergence of antimicrobial-resistant pathogens. However, previous studies using these designs have often used suboptimal statistical methods, which may result in researchers making spurious conclusions. Methods used to analyze quasi-experimental data include 2-group tests, regression analysis, and time-series analysis, and they all have specific assumptions, data requirements, strengths, and limitations. An example of a hospital-based intervention to reduce methicillin-resistant Staphylococcus aureus infection rates and reduce overall length of stay is used to explore these methods.

Experimental study and constitutive modeling of the viscoelastic mechanical properties of the human prolapsed vaginal tissue.

PubMed

Peña, Estefania; Calvo, B; Martínez, M A; Martins, P; Mascarenhas, T; Jorge, R M N; Ferreira, A; Doblaré, M

2010-02-01

In this paper, the viscoelastic mechanical properties of vaginal tissue are investigated. Using previous results of the authors on the mechanical properties of biological soft tissues and newly experimental data from uniaxial tension tests, a new model for the viscoelastic mechanical properties of the human vaginal tissue is proposed. The structural model seems to be sufficiently accurate to guarantee its application to prediction of reliable stress distributions, and is suitable for finite element computations. The obtained results may be helpful in the design of surgical procedures with autologous tissue or prostheses.

Proof test criteria for thin-walled 2219 aluminum pressure vessels. Volume 1: Program summary and data analysis

NASA Technical Reports Server (NTRS)

Finger, R. W.

1976-01-01

This experimental program was undertaken to investigate the crack growth behavior of deep surface flaws in 2219 aluminum. The program included tests of uniaxially loaded surface flaw and center crack panels at temperatures ranging from 20K (-423 F) to ambient. The tests were conducted on both the base metal and as-welded weld metal material. The program was designed to provide data on the mechanisms of failure by ligament penetration, and the residual cyclic life, after proof-testing, of a vessel which has been subjected to incipient penetration by the proof test. The results were compared and analyzed with previously developed data to develop guidelines for the proof testing of thin walled 2219 pressure vessels.

The Effect of Internal Pressure on the Buckling Stress of Thin-Walled Circular Cylinders Under Torsion

NASA Technical Reports Server (NTRS)

Crate, Harold; Batdorf, S B; Baab, George W

1944-01-01

The results of a series of tests to determine the effect of internal pressure on the buckling load of a thin cylinder under an applied torque indicated that internal pressure raises the shear buckling stress. The experimental results were analyzed with the aid of previously developed theory and a simple interaction formula was derived. (author)

Measurement of Latent Variables with Different Rating Scales: Testing Reliability and Measurement Equivalence by Varying the Verbalization and Number of Categories

ERIC Educational Resources Information Center

Menold, Natalja; Tausch, Anja

2016-01-01

Effects of rating scale forms on cross-sectional reliability and measurement equivalence were investigated. A randomized experimental design was implemented, varying category labels and number of categories. The participants were 800 students at two German universities. In contrast to previous research, reliability assessment method was used,…

Play and Associative Fluency: Experimenter Effects May Be Responsible for Previous Positive Findings.

ERIC Educational Resources Information Center

Smith, Peter K.; Whitney, Sue

1987-01-01

A total of 64 preschool children were assigned to one of three conditions--fantasy play, play, or imitation--with common objects, or to an alternative-materials group. Subjects were tested for associative fluency for familiar and novel objects, both immediately and after a delay of one week. No significant main effects for condition were found.…

Off-design performance loss model for radial turbines with pivoting, variable-area stators

NASA Technical Reports Server (NTRS)

Meitner, P. L.; Glassman, A. J.

1980-01-01

An off-design performance loss model was developed for variable stator (pivoted vane), radial turbines through analytical modeling and experimental data analysis. Stator loss is determined by a viscous loss model; stator vane end-clearance leakage effects are determined by a clearance flow model. Rotor loss coefficient were obtained by analyzing the experimental data from a turbine rotor previously tested with six stators having throat areas from 20 to 144 percent of design area and were correlated with stator-to-rotor throat area ratio. An incidence loss model was selected to obtain best agreement with experimental results. Predicted turbine performance is compared with experimental results for the design rotor as well as with results for extended and cutback versions of the rotor. Sample calculations were made to show the effects of stator vane end-clearance leakage.

Experimental Investigation of Wind-Tunnel Interference on the Downwash Behind an Airfoil

NASA Technical Reports Server (NTRS)

Silverstein, Abe; Katzoff, S

1937-01-01

The interference of the wind-tunnel boundaries on the downwash behind an airfoil has been experimentally investigated and the results have been compared with the available theoretical results for open-throat wind tunnels. As in previous studies, the simplified theoretical treatment that assumes the test section to be an infinite free jet has been shown to be satisfactory at the lifting line. The experimental results, however, show that this assumption may lead to erroneous conclusions regarding the corrections to be applied to the downwash in the region behind the airfoil where the tail surfaces are normally located. The results of a theory based on the more accurate concept of the open-jet wind tunnel as a finite length of free jet provided with a closed exit passage are in good qualitative agreement with the experimental results.

Computational and Experimental Study of Supersonic Nozzle Flow and Shock Interactions

NASA Technical Reports Server (NTRS)

Carter, Melissa B.; Elmiligui, Alaa A.; Nayani, Sudheer N.; Castner, Ray; Bruce, Walter E., IV; Inskeep, Jacob

2015-01-01

This study focused on the capability of NASA Tetrahedral Unstructured Software System's CFD code USM3D capability to predict the interaction between a shock and supersonic plume flow. Previous studies, published in 2004, 2009 and 2013, investigated USM3D's supersonic plume flow results versus historical experimental data. This current study builds on that research by utilizing the best practices from the early papers for properly capturing the plume flow and then adding a wedge acting as a shock generator. This computational study is in conjunction with experimental tests conducted at the Glenn Research Center 1'x1' Supersonic Wind Tunnel. The comparison of the computational and experimental data shows good agreement for location and strength of the shocks although there are vertical shifts between the data sets that may be do to the measurement technique.

Basic performance of a multilayer insulation system containing 20 to 160 layers. [thermal effectiveness of aluminized Mylar-silk net system

NASA Technical Reports Server (NTRS)

Stochl, R. J.

1974-01-01

An experimental investigation was conducted to determine the thermal effectiveness of an aluminized Mylar-silk net insulation system containing up to 160 layers. The experimentally measured heat flux was compared with results predicted by using (1) a previously developed semi-empirical equation and (2) an effective-thermal-conductivity value. All tests were conducted at a nominal hot-boundary temperature of 294 K (530 R) with liquid hydrogen as the heat sink. The experimental results show that the insulation performed as expected and that both the semi-empirical equation and effective thermal conductivity of a small number of layers were adequate in predicting the thermal performance of a large number of layers of insulation.

From military to civil loadings: Preliminary numerical-based thorax injury criteria investigations.

PubMed

Goumtcha, Aristide Awoukeng; Bodo, Michèle; Taddei, Lorenzo; Roth, Sébastien

2016-03-01

Effects of the impact of a mechanical structure on the human body are of great interest in the understanding of body trauma. Experimental tests have led to first conclusions about the dangerousness of an impact observing impact forces or displacement time history with PMHS (Post Mortem human Subjects). They have allowed providing interesting data for the development and the validation of numerical biomechanical models. These models, widely used in the framework of automotive crashworthiness, have led to the development of numerical-based injury criteria and tolerance thresholds. The aim of this process is to improve the safety of mechanical structures in interaction with the body. In a military context, investigations both at experimental and numerical level are less successfully completed. For both military and civil frameworks, the literature list a number of numerical analysis trying to propose injury mechanisms, and tolerance thresholds based on biofidelic Finite Element (FE) models of different part of the human body. However the link between both frameworks is not obvious, since lots of parameters are different: great mass impacts at relatively low velocity for civil impacts (falls, automotive crashworthiness) and low mass at very high velocity for military loadings (ballistic, blast). In this study, different accident cases were investigated, and replicated with a previously developed and validated FE model of the human thorax named Hermaphrodite Universal Biomechanical YX model (HUBYX model). These previous validations included replications of standard experimental tests often used to validate models in the context of automotive industry, experimental ballistic tests in high speed dynamic impact and also numerical replication of blast loading test ensuring its biofidelity. In order to extend the use of this model in other frameworks, some real-world accidents were reconstructed, and consequences of these loadings on the FE model were explored. These various numerical replications of accident coming from different contexts raise the question about the ability of a FE model to correctly predict several kinds of trauma, from blast or ballistic impacts to falls, sports or automotive ones in a context of numerical injury mechanisms and tolerance limits investigations. Copyright © 2015 John Wiley & Sons, Ltd.

A menu of self-administered microcomputer-based neurotoxicology tests

NASA Technical Reports Server (NTRS)

Kennedy, Robert S.; Wilkes, Robert L.; Kuntz, Lois-Ann; Baltzley, Dennis R.

1988-01-01

This study examined the feasibility of repeated self-administration of a newly developed battery of mental acuity tests. Researchers developed this battery to be used to screen the fitness for duty of persons in at-risk occupations (astronauts, race car drivers), or those who may be exposed to environmental stress, toxic agents, or disease. The menu under study contained cognitive and motor tests implemented on a portable microcomputer including: a five-test core battery, lasting six minutes, which had demonstrable reliabilities and stability from several previous repeated-measures studies, and also 13 new tests, lasting 42 minutes, which had appeared in other batteries but had not yet been evaluated for repeated-measures implementation in this medium. Sixteen subjects self-administered the battery over 10 repeated sessions. The hardware performed well throughout the study and the tests appeared to be easily self-administered. Stabilities and reliabilities of the test from the core battery were comparable to those obtained previously under more controlled experimental conditions. Analyses of metric properties of the remaining 13 tests produced eight additional tests with satisfactory properties. Although the average retest reliability was high, cross-correlations between tests were low, indicating factorial richness. The menu can be used to form batteries of flexible total testing time which are likely to tap different mental processes and functions.

Experimental Hydromechanical Characterization and Numerical Modelling of a Fractured and Porous Sandstone

NASA Astrophysics Data System (ADS)

Souley, Mountaka; Lopez, Philippe; Boulon, Marc; Thoraval, Alain

2015-05-01

The experimental device previously used to study the hydromechanical behaviour of individual fractures on a laboratory scale, was adapted to make it possible to measure flow through porous rock mass samples in addition to fracture flows. A first series of tests was performed to characterize the hydromechanical behaviour of the fracture individually as well as the porous matrix (sandstone) comprising the fracture walls. A third test in this series was used to validate the experimental approach. These tests showed non-linear evolution of the contact area on the fracture walls with respect to effective normal stress. Consequently, a non-linear relationship was noted between the hydraulic aperture on the one hand, and the effective normal stress and mechanical opening on the other hand. The results of the three tests were then analysed by numerical modelling. The VIPLEF/HYDREF numerical codes used take into account the dual-porosity of the sample (fracture + rock matrix) and can be used to reproduce hydromechanical loading accurately. The analyses show that the relationship between the hydraulic aperture of the fracture and the mechanical closure has a significant effect on fracture flow rate predictions. By taking simultaneous measurements of flow in both fracture and rock matrix, we were able to carry out a global evaluation of the conceptual approach used.

Versatile Analysis of Single-Molecule Tracking Data by Comprehensive Testing against Monte Carlo Simulations

PubMed Central

Wieser, Stefan; Axmann, Markus; Schütz, Gerhard J.

2008-01-01

We propose here an approach for the analysis of single-molecule trajectories which is based on a comprehensive comparison of an experimental data set with multiple Monte Carlo simulations of the diffusion process. It allows quantitative data analysis, particularly whenever analytical treatment of a model is infeasible. Simulations are performed on a discrete parameter space and compared with the experimental results by a nonparametric statistical test. The method provides a matrix of p-values that assess the probability for having observed the experimental data at each setting of the model parameters. We show the testing approach for three typical situations observed in the cellular plasma membrane: i), free Brownian motion of the tracer, ii), hop diffusion of the tracer in a periodic meshwork of squares, and iii), transient binding of the tracer to slowly diffusing structures. By plotting the p-value as a function of the model parameters, one can easily identify the most consistent parameter settings but also recover mutual dependencies and ambiguities which are difficult to determine by standard fitting routines. Finally, we used the test to reanalyze previous data obtained on the diffusion of the glycosylphosphatidylinositol-protein CD59 in the plasma membrane of the human T24 cell line. PMID:18805933

The Language Research Center's Computerized Test System for environmental enrichment and psychological assessment

NASA Technical Reports Server (NTRS)

Washburn, D. A.; Rumbaugh, D. M.; Richardson, W. K.

1992-01-01

In the spring of 1987, we undertook to provide environmental enrichment to nonhuman primate subjects in ways that would complement and even contribute to the bio-behaviorial science that justified the monkeys' captivity. Of course, the psychological well-being of captive primates--and indeed all research species-- has been an area of intense research activity since the 1985 amendment of the Animal Welfare Act. This mandate for researchers to ensure the psychological, as well as physical, fitness of experimental animals catalyzed the humane and scientific interests of the research community. The contemporary literature is replete with proposed means both of assaying and of providing enrichment and well-being. Notwithstanding, consensus on either assessment or intervention has yet to be reached. The paradigm we employed was modelled after successful efforts with chimpanzees. An automated test system was constructed in which subjects responded to computer tasks by manipulating a joystick. The tasks, interactive game-like versions of many of the classic testing paradigms of cognitive and comparative psychology, permitted the controlled presentation of stimuli and demands without the required presence of a human experimenter. Despite significant barriers to the success, rhesus monkeys (Macaca mulatta) and a variety of other primate species (including, of course, humans) have mastered the skills necessary for testing in this paradigm. Previous experiments have illustrated the utility of the test system for addressing questions of learning, memory, attention, perception, and motivation. Additional data have been reported to support the contention that the Language Research Center's Computerized Test System (LRC-CTS) serves its other raison d'etre--providing environmental enrichment and assessing psychological well-being. This paper is designed to augment previous descriptions of the technology and the paradigm for scientists and caretakers interested in environmental enrichment and performance assessment with primates.

The fragrance hand immersion study - an experimental model simulating real-life exposure for allergic contact dermatitis on the hands.

PubMed

Heydorn, S; Menné, T; Andersen, K E; Bruze, M; Svedman, C; Basketter, D; Johansen, J D

2003-06-01

Recently, we showed that 10 x 2% of consecutively patch-tested hand eczema patients had a positive patch test to a selection of fragrances containing fragrances relevant to hand exposure. In this study, we used repeated skin exposure to a patch test-positive fragrance allergen in patients previously diagnosed with hand eczema to explore whether immersion of fingers in a solution with or without the patch-test-positive fragrance allergen would cause or exacerbate hand eczema on the exposed finger. The study was double blinded and randomized. All participants had a positive patch test to either hydroxycitronellal or Lyral (hydroxyisohexyl 3-cyclohexene carboxaldehyde). Each participant immersed a finger from each hand, once a day, in a solution containing the fragrance allergen or placebo. During the first 2 weeks, the concentration of fragrance allergen in the solution was low (approximately 10 p.p.m.), whilst during the following 2 weeks, the concentration was relatively high (approximately 250 p.p.m.), imitating real-life exposure to a household product like dishwashing liquid diluted in water and the undiluted product, respectively. Evaluation was made using a clinical scale and laser Doppler flow meter. 3 of 15 hand eczema patients developed eczema on the finger immersed in the fragrance-containing solution, 3 of 15 on the placebo finger and 3 of 15 on both fingers. Using this experimental exposure model simulating real-life exposure, we found no association between immersion of a finger in a solution containing fragrance and development of clinically visible eczema on the finger in 15 participants previously diagnosed with hand eczema and with a positive patch test to the fragrance in question.

Water Capture Device Signal Integration Board

NASA Technical Reports Server (NTRS)

Chamberlin, Kathryn J.; Hartnett, Andrew J.

2018-01-01

I am a junior in electrical engineering at Arizona State University, and this is my second internship at Johnson Space Center. I am an intern in the Command and Data Handling Branch of Avionics Division (EV2), my previous internship was also in EV2. During my previous internship I was assigned to the Water Capture Device payload, where I designed a prototype circuit board for the electronics system of the payload. For this internship, I have come back to the Water Capture Device project to further the work on the electronics design I completed previously. The Water Capture Device is an experimental payload to test the functionality of two different phase separators aboard the International Space Station (ISS). A phase separator sits downstream of a condensing heat exchanger (CHX) and separates the water from the air particles for environmental control on the ISS. With changing CHX technology, new phase separators are required. The goal of the project is to develop a test bed for the two phase separators to determine the best solution.

Combining existing numerical models with data assimilation using weighted least-squares finite element methods.

PubMed

Rajaraman, Prathish K; Manteuffel, T A; Belohlavek, M; Heys, Jeffrey J

2017-01-01

A new approach has been developed for combining and enhancing the results from an existing computational fluid dynamics model with experimental data using the weighted least-squares finite element method (WLSFEM). Development of the approach was motivated by the existence of both limited experimental blood velocity in the left ventricle and inexact numerical models of the same flow. Limitations of the experimental data include measurement noise and having data only along a two-dimensional plane. Most numerical modeling approaches do not provide the flexibility to assimilate noisy experimental data. We previously developed an approach that could assimilate experimental data into the process of numerically solving the Navier-Stokes equations, but the approach was limited because it required the use of specific finite element methods for solving all model equations and did not support alternative numerical approximation methods. The new approach presented here allows virtually any numerical method to be used for approximately solving the Navier-Stokes equations, and then the WLSFEM is used to combine the experimental data with the numerical solution of the model equations in a final step. The approach dynamically adjusts the influence of the experimental data on the numerical solution so that more accurate data are more closely matched by the final solution and less accurate data are not closely matched. The new approach is demonstrated on different test problems and provides significantly reduced computational costs compared with many previous methods for data assimilation. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Experimental Characterization and Micromechanical Modeling of Woven Carbon/Copper Composites

NASA Technical Reports Server (NTRS)

Bednarcyk, Brett A.; Pauly, Christopher C.; Pindera, Marek-Jerzy

1997-01-01

The results of an extensive experimental characterization and a preliminary analytical modeling effort for the elastoplastic mechanical behavior of 8-harness satin weave carbon/copper (C/Cu) composites are presented. Previous experimental and modeling investigations of woven composites are discussed, as is the evolution of, and motivation for, the continuing research on C/Cu composites. Experimental results of monotonic and cyclic tension, compression, and Iosipescu shear tests, and combined tension-compression tests, are presented. With regard to the test results, emphasis is placed on the effect of strain gauge size and placement, the effect of alloying the copper matrix to improve fiber-matrix bonding, yield surface characterization, and failure mechanisms. The analytical methodology used in this investigation consists of an extension of the three-dimensional generalized method of cells (GMC-3D) micromechanics model, developed by Aboudi (1994), to include inhomogeneity and plasticity effects on the subcell level. The extension of the model allows prediction of the elastoplastic mechanical response of woven composites, as represented by a true repeating unit cell for the woven composite. The model is used to examine the effects of refining the representative geometry of the composite, altering the composite overall fiber volume fraction, changing the size and placement of the strain gauge with respect to the composite's reinforcement weave, and including porosity within the infiltrated fiber yarns on the in-plane elastoplastic tensile, compressive, and shear response of 8-harness satin C/Cu. The model predictions are also compared with the appropriate monotonic experimental results.

Oscillating-flow regenerator test rig

NASA Technical Reports Server (NTRS)

Wood, J. G.; Gedeon, D. R.

1994-01-01

This report summarizes work performed in setting up and performing tests on a regenerator test rig. An earlier status report presented test results, together with heat transfer correlations, for four regenerator samples (two woven screen samples and two felt metal samples). Lessons learned from this testing led to improvements to the experimental setup, mainly instrumentation as well as to the test procedure. Given funding and time constraints for this project it was decided to complete as much testing as possible while the rig was set up and operational, and to forego final data reduction and analysis until later. Additional testing was performed on several of the previously tested samples as well an on five newly fabricated samples. The following report is a summary of the work performed at OU, with many of the final test results included in raw data form.

Effect of Skin Cancer Training Provided to Maritime High School Students on Their Knowledge and Behaviour.

PubMed

Sümen, Adem; Öncel, Selma

2015-01-01

This study was conducted with the purpose of evaluating the effect of skin cancer training provided to maritime high school students on their knowledge and behaviour. The study had a quasi-experimental design with pre-test and post-test intervention and control groups. Two maritime high schools located in the city of Antalya were included within the scope of the study between March and June 2013, covering a total of 567 students. While the knowledge mean scores of students regarding skin cancer and sun protection did not vary in the pre-test (6.2 ± 1.9) and post-test (6.8 ± 1.9) control group, the knowledge mean scores of students in the experimental group increased from 6.0 ± 2.3 to 10.6 ± 1.2 after the provided training. Some 25.4% of students in the experimental group had low knowledge level and 62.2% had medium knowledge level in the pre-test; whereas no students had low knowledge level and 94.3% had high knowledge level in the post-test. It was determined that tenth grade students, those who had previous knowledge on the subject, who considered themselves to be protecting from the sun better, had higher knowledge levels and their knowledge levels increased as the risk level increased. It was found that the provided training was effective and increased positively the knowledge, attitude and behaviour levels of students in the experimental group in terms of skin cancer and sun protection. Along with the provided training which started to form a lifestyle, appropriate attitudes and behaviours concerning skin cancer and sun protection could be brought to students who will work in outdoor spaces and are members of the maritime profession within the risk group.

Multimodal Emotion Recognition Is Resilient to Insufficient Sleep: Results From Cross-Sectional and Experimental Studies.

PubMed

Holding, Benjamin C; Laukka, Petri; Fischer, Håkan; Bänziger, Tanja; Axelsson, John; Sundelin, Tina

2017-11-01

Insufficient sleep has been associated with impaired recognition of facial emotions. However, previous studies have found inconsistent results, potentially stemming from the type of static picture task used. We therefore examined whether insufficient sleep was associated with decreased emotion recognition ability in two separate studies using a dynamic multimodal task. Study 1 used a cross-sectional design consisting of 291 participants with questionnaire measures assessing sleep duration and self-reported sleep quality for the previous night. Study 2 used an experimental design involving 181 participants where individuals were quasi-randomized into either a sleep-deprivation (N = 90) or a sleep-control (N = 91) condition. All participants from both studies were tested on the same forced-choice multimodal test of emotion recognition to assess the accuracy of emotion categorization. Sleep duration, self-reported sleep quality (study 1), and sleep deprivation (study 2) did not predict overall emotion recognition accuracy or speed. Similarly, the responses to each of the twelve emotions tested showed no evidence of impaired recognition ability, apart from one positive association suggesting that greater self-reported sleep quality could predict more accurate recognition of disgust (study 1). The studies presented here involve considerably larger samples than previous studies and the results support the null hypotheses. Therefore, we suggest that the ability to accurately categorize the emotions of others is not associated with short-term sleep duration or sleep quality and is resilient to acute periods of insufficient sleep. © Sleep Research Society 2017. Published by Oxford University Press on behalf of the Sleep Research Society. All rights reserved. For permissions, please e-mail journals.permissions@oup.com.

Evaluation of the New B-REX Fatigue Testing System for Multi-Megawatt Wind Turbine Blades: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, D.; Musial, W.; Engberg, S.

2004-12-01

The National Renewable Energy Laboratory (NREL) recently developed a new hybrid fatigue testing system called the Blade Resonance Excitation (B-REX) test system. The new system uses 65% less energy to test large wind turbine blades in half the time of NREL's dual-axis forced-displacement test method with lower equipment and operating costs. The B-REX is a dual-axis test system that combines resonance excitation with forced hydraulic loading to reduce the total test time required while representing the operating strains on the critical inboard blade stations more accurately than a single-axis test system. The analysis and testing required to fully implement themore » B-REX was significant. To control unanticipated blade motion and vibrations caused by dynamic coupling between the flap, lead-lag, and torsional directions, we needed to incorporate additional test hardware and control software. We evaluated the B-REX test system under stable operating conditions using a combination of various sensors. We then compared our results with results from the same blade, tested previously using NREL's dual-axis forced-displacement test method. Experimental results indicate that strain levels produced by the B-REX system accurately replicated the forced-displacement method. This paper describes the challenges we encountered while developing the new blade fatigue test system and the experimental results that validate its accuracy.« less

Experimental identification of the behaviour of and lateral forces from freely-walking pedestrians on laterally oscillating structures in a virtual reality environment.

PubMed

Bocian, Mateusz; Macdonald, John H G; Burn, Jeremy F; Redmill, David

2015-12-15

Modelling pedestrian loading on lively structures such as bridges remains a challenge. This is because pedestrians have the capacity to interact with vibrating structures which can lead to amplification of the structural response. Current design guidelines are often inaccurate and limiting as they do not sufficiently acknowledge this effect. This originates in scarcity of data on pedestrian behaviour on vibrating ground and uncertainty as to the accuracy of results from previous experimental campaigns aiming to quantify pedestrian behaviour in this case. To this end, this paper presents a novel experimental setup developed to evaluate pedestrian actions on laterally oscillating ground in the laboratory environment while avoiding the implications of artificiality and allowing for unconstrained gait. A biologically-inspired approach was adopted in its development, relying on appreciation of operational complexities of biological systems, in particular their adaptability and control requirements. In determination of pedestrian forces to the structure consideration was given to signal processing issues which have been neglected in past studies. The results from tests conducted on the setup are related to results from previous experimental investigations and outputs of the inverted pendulum pedestrian model for walking on laterally oscillating ground, which is capable of generating self-excited forces.

Context specificity of inhibitory control in dogs

PubMed Central

MacLean, Evan L.; Hare, Brian A.

2014-01-01

Across three experiments, we explored whether a dog's capacity for inhibitory control is stable or variable across decision-making contexts. In the social task, dogs were first exposed to the reputations of a stingy experimenter that never shared food and a generous experimenter who always shared food. In subsequent test trials, dogs were required to avoid approaching the stingy experimenter when this individual offered (but withheld) a higher-value reward than the generous experimenter did. In the A-not-B task, dogs were required to inhibit searching for food in a previously rewarded location after witnessing the food being moved from this location to a novel hiding place. In the cylinder task, dogs were required to resist approaching visible food directly (because it was behind a transparent barrier), in favor of a detour reaching response. Overall, dogs exhibited inhibitory control in all three tasks. However, individual scores were not correlated between tasks, suggesting that context has a large effect on dogs' behavior. This result mirrors studies of humans, which have highlighted intra-individual variation in inhibitory control as a function of the decision-making context. Lastly, we observed a correlation between a subject's age and performance on the cylinder task, corroborating previous observations of age-related decline in dogs' executive function. PMID:23584618

Computer-aided design of liposomal drugs: In silico prediction and experimental validation of drug candidates for liposomal remote loading.

PubMed

Cern, Ahuva; Barenholz, Yechezkel; Tropsha, Alexander; Goldblum, Amiram

2014-01-10

Previously we have developed and statistically validated Quantitative Structure Property Relationship (QSPR) models that correlate drugs' structural, physical and chemical properties as well as experimental conditions with the relative efficiency of remote loading of drugs into liposomes (Cern et al., J. Control. Release 160 (2012) 147-157). Herein, these models have been used to virtually screen a large drug database to identify novel candidate molecules for liposomal drug delivery. Computational hits were considered for experimental validation based on their predicted remote loading efficiency as well as additional considerations such as availability, recommended dose and relevance to the disease. Three compounds were selected for experimental testing which were confirmed to be correctly classified by our previously reported QSPR models developed with Iterative Stochastic Elimination (ISE) and k-Nearest Neighbors (kNN) approaches. In addition, 10 new molecules with known liposome remote loading efficiency that were not used by us in QSPR model development were identified in the published literature and employed as an additional model validation set. The external accuracy of the models was found to be as high as 82% or 92%, depending on the model. This study presents the first successful application of QSPR models for the computer-model-driven design of liposomal drugs. © 2013.

Computer-aided design of liposomal drugs: in silico prediction and experimental validation of drug candidates for liposomal remote loading

PubMed Central

Cern, Ahuva; Barenholz, Yechezkel; Tropsha, Alexander; Goldblum, Amiram

2014-01-01

Previously we have developed and statistically validated Quantitative Structure Property Relationship (QSPR) models that correlate drugs’ structural, physical and chemical properties as well as experimental conditions with the relative efficiency of remote loading of drugs into liposomes (Cern et al, Journal of Controlled Release, 160(2012) 14–157). Herein, these models have been used to virtually screen a large drug database to identify novel candidate molecules for liposomal drug delivery. Computational hits were considered for experimental validation based on their predicted remote loading efficiency as well as additional considerations such as availability, recommended dose and relevance to the disease. Three compounds were selected for experimental testing which were confirmed to be correctly classified by our previously reported QSPR models developed with Iterative Stochastic Elimination (ISE) and k-nearest neighbors (kNN) approaches. In addition, 10 new molecules with known liposome remote loading efficiency that were not used in QSPR model development were identified in the published literature and employed as an additional model validation set. The external accuracy of the models was found to be as high as 82% or 92%, depending on the model. This study presents the first successful application of QSPR models for the computer-model-driven design of liposomal drugs. PMID:24184343

Experimental control requirements for life sciences

NASA Technical Reports Server (NTRS)

Berry, W. E.; Sharp, J. C.

1978-01-01

The Life Sciences dedicated Spacelab will enable scientists to test hypotheses in various disciplines. Building upon experience gained in mission simulations, orbital flight test experiments, and the first three Spacelab missions, NASA will be able to progressively develop the engineering and management capabilities necessary for the first Life Sciences Spacelab. Development of experiments for these missions will require implementation of life-support systems not previously flown in space. Plant growth chambers, animal holding facilities, aquatic specimen life-support systems, and centrifuge-mounted specimen holding units are examples of systems currently being designed and fabricated for flight.

Temperature and Atomic Oxygen Effects on Helium Leak Rates of a Candidate Main Interface Seal

NASA Technical Reports Server (NTRS)

Penney, Nicholas; Wasowski, Janice L.; Daniels, Christopher C.

2011-01-01

Helium leak tests were completed to characterize the leak rate of a 54 in. diameter composite space docking seal design in support of the National Aeronautics and Space Administration s (NASA's) Low Impact Docking System (LIDS). The evaluated seal design was a candidate for the main interface seal on the LIDS, which would be compressed between two vehicles, while docked, to prevent the escape of breathable air from the vehicles and into the vacuum of space. Leak tests completed at nominal temperatures of -30, 20, and 50 C on untreated and atomic oxygen (AO) exposed test samples were examined to determine the influence of both test temperature and AO exposure on the performance of the composite seal assembly. Results obtained for untreated seal samples showed leak rates which increased with increased test temperature. This general trend was not observed in tests of the AO exposed specimens. Initial examination of collected test data suggested that AO exposure resulted in higher helium leak rates, however, further analysis showed that the differences observed in the 20 and 50 C tests between the untreated and AO exposed samples were within the experimental error of the test method. Lack of discernable trends in the test data prevented concrete conclusions about the effects of test temperature and AO exposure on helium leak rates of the candidate seal design from being drawn. To facilitate a comparison of the current test data with results from previous leak tests using air as the test fluid, helium leak rates were converted to air leak rates using standard conversion factors for viscous and molecular flow. Flow rates calculated using the viscous flow conversion factor were significantly higher than the experimental air leakage values, whereas values calculated using the molecular flow conversion factor were significantly lower than the experimentally obtained air leak rates. The difference in these sets of converted flow rates and their deviation from the experimentally obtained air leak rate data suggest that neither conversion factor can be used alone to accurately convert helium leak rates to equivalent air leak rates for the test seals evaluated in this study; other leak phenomena, including permeation, must also be considered.

Simulation of an Impact Test of the All-Composite Lear Fan Aircraft

NASA Technical Reports Server (NTRS)

Stockwell, Alan E.; Jones, Lisa E. (Technical Monitor)

2002-01-01

An MSC.Dytran model of an all-composite Lear Fan aircraft fuselage was developed to simulate an impact test conducted at the NASA Langley Research Center Impact Dynamics Research Facility (IDRF). The test was the second of two Lear Fan impact tests. The purpose of the second test was to evaluate the performance of retrofitted composite energy-absorbing floor beams. A computerized photogrammetric survey was performed to provide airframe geometric coordinates, and over 5000 points were processed and imported into MSC.Patran via an IGES file. MSC.Patran was then used to develop the curves and surfaces and to mesh the finite element model. A model of the energy-absorbing floor beams was developed separately and then integrated into the Lear Fan model. Structural responses of components such as the wings were compared with experimental data or previously published analytical data wherever possible. Comparisons with experimental results were used to guide structural model modifications to improve the simulation performance. This process was based largely on qualitative (video and still camera images and post-test inspections) rather than quantitative results due to the relatively few accelerometers attached to the structure.

Experimental Searches for Exotic Short-Range Forces Using Mechanical Oscillators

NASA Astrophysics Data System (ADS)

Weisman, Evan

Experimental searches for forces beyond gravity and electromagnetism at short range have attracted a great deal of attention over the last decade. In this thesis I describe the test mass development for two new experiments searching for forces below 1 mm. Both modify a previous experiment that used 1 kHz mechanical oscillators as test masses with a stiff conducting shield between them to suppress backgrounds, a promising technique for probing exceptionally small distances at the limit of instrumental thermal noise. To further reduce thermal noise, one experiment will use plated silicon test masses at cryogenic temperatures. The other experiment, which searches for spin-dependent interactions, will apply the spin-polarizable material Dy3Fe5O 12 to the test mass surfaces. This material exhibits orbital compensation of the magnetism associated with its intrinsic electron spin, minimizing magnetic backgrounds. Several plated silicon test mass prototypes were fabricated using photolithography (useful in both experiments), and spin-dependent materials were synthesized with a simple chemical recipe. Both silicon and spin-dependent test masses demonstrate the mechanical and magnetic properties necessary for sensitive experiments. I also describe sensitivity calculations of another proposed spin-dependent experiment, based on a modified search for the electron electric dipole moment, which show unprecedented sensitivity to exotic monopole-dipole forces. Inspired by a finite element model, a study attempting to maximize detector quality factor versus geometry is also presented, with experimental results so far not explained by the model.

A comparative analysis of experimental selection on the stickleback pelvis.

PubMed

Miller, S E; Barrueto, M; Schluter, D

2017-06-01

Mechanisms of natural selection can be identified using experimental approaches. However, such experiments often yield nonsignificant effects and imprecise estimates of selection due to low power and small sample sizes. Combining results from multiple experimental studies might produce an aggregate estimate of selection that is more revealing than individual studies. For example, bony pelvic armour varies conspicuously among stickleback populations, and predation by vertebrate and insect predators has been hypothesized to be the main driver of this variation. Yet experimental selection studies testing these hypotheses frequently fail to find a significant effect. We experimentally manipulated length of threespine stickleback (Gasterosteus aculeatus) pelvic spines in a mesocosm experiment to test whether prickly sculpin (Cottus asper), an intraguild predator of stickleback, favours longer spines. The probability of survival was greater for stickleback with unclipped pelvic spines, but this effect was noisy and not significant. We used meta-analysis to combine the results of our mesocosm experiment with previously published experimental studies of selection on pelvic armour. We found evidence that fish predation indeed favours increased pelvic armour, with a moderate effect size. The same approach found little evidence that insect predation favours reduced pelvic armour. The causes of reduced pelvic armour in many stickleback populations remain uncertain. © 2017 European Society For Evolutionary Biology. Journal of Evolutionary Biology © 2017 European Society For Evolutionary Biology.

Learned perceptual associations influence visuomotor programming under limited conditions: kinematic consistency.

PubMed

Haffenden, Angela M; Goodale, Melvyn A

2002-12-01

Previous findings have suggested that visuomotor programming can make use of learned size information in experimental paradigms where movement kinematics are quite consistent from trial to trial. The present experiment was designed to test whether or not this conclusion could be generalized to a different manipulation of kinematic variability. As in previous work, an association was established between the size and colour of square blocks (e.g. red = large; yellow = small, or vice versa). Associating size and colour in this fashion has been shown to reliably alter the perceived size of two test blocks halfway in size between the large and small blocks: estimations of the test block matched in colour to the group of large blocks are smaller than estimations of the test block matched to the group of small blocks. Subjects grasped the blocks, and on other trials estimated the size of the blocks. These changes in perceived block size were incorporated into grip scaling only when movement kinematics were highly consistent from trial to trial; that is, when the blocks were presented in the same location on each trial. When the blocks were presented in different locations grip scaling remained true to the metrics of the test blocks despite the changes in perceptual estimates of block size. These results support previous findings suggesting that kinematic consistency facilitates the incorporation of learned perceptual information into grip scaling.

Advanced air revitalization system testing

NASA Technical Reports Server (NTRS)

Heppner, D. B.; Hallick, T. M.; Schubert, F. H.

1983-01-01

A previously developed experimental air revitalization system was tested cyclically and parametrically. One-button startup without manual interventions; extension by 1350 hours of tests with the system; capability for varying process air carbon dioxide partial pressure and humidity and coolant source for simulation of realistic space vehicle interfaces; dynamic system performance response on the interaction of the electrochemical depolarized carbon dioxide concentrator, the Sabatier carbon dioxide reduction subsystem, and the static feed water electrolysis oxygen generation subsystem, the carbon dioxide concentrator module with unitized core technology for the liquid cooled cell; and a preliminary design for a regenerative air revitalization system for the space station are discussed.

The geometry of distributional preferences and a non-parametric identification approach: The Equality Equivalence Test.

PubMed

Kerschbamer, Rudolf

2015-05-01

This paper proposes a geometric delineation of distributional preference types and a non-parametric approach for their identification in a two-person context. It starts with a small set of assumptions on preferences and shows that this set (i) naturally results in a taxonomy of distributional archetypes that nests all empirically relevant types considered in previous work; and (ii) gives rise to a clean experimental identification procedure - the Equality Equivalence Test - that discriminates between archetypes according to core features of preferences rather than properties of specific modeling variants. As a by-product the test yields a two-dimensional index of preference intensity.

e-Bitter: Bitterant Prediction by the Consensus Voting From the Machine-Learning Methods

PubMed Central

Zheng, Suqing; Jiang, Mengying; Zhao, Chengwei; Zhu, Rui; Hu, Zhicheng; Xu, Yong; Lin, Fu

2018-01-01

In-silico bitterant prediction received the considerable attention due to the expensive and laborious experimental-screening of the bitterant. In this work, we collect the fully experimental dataset containing 707 bitterants and 592 non-bitterants, which is distinct from the fully or partially hypothetical non-bitterant dataset used in the previous works. Based on this experimental dataset, we harness the consensus votes from the multiple machine-learning methods (e.g., deep learning etc.) combined with the molecular fingerprint to build the bitter/bitterless classification models with five-fold cross-validation, which are further inspected by the Y-randomization test and applicability domain analysis. One of the best consensus models affords the accuracy, precision, specificity, sensitivity, F1-score, and Matthews correlation coefficient (MCC) of 0.929, 0.918, 0.898, 0.954, 0.936, and 0.856 respectively on our test set. For the automatic prediction of bitterant, a graphic program “e-Bitter” is developed for the convenience of users via the simple mouse click. To our best knowledge, it is for the first time to adopt the consensus model for the bitterant prediction and develop the first free stand-alone software for the experimental food scientist. PMID:29651416

e-Bitter: Bitterant Prediction by the Consensus Voting From the Machine-learning Methods

NASA Astrophysics Data System (ADS)

Zheng, Suqing; Jiang, Mengying; Zhao, Chengwei; Zhu, Rui; Hu, Zhicheng; Xu, Yong; Lin, Fu

2018-03-01

In-silico bitterant prediction received the considerable attention due to the expensive and laborious experimental-screening of the bitterant. In this work, we collect the fully experimental dataset containing 707 bitterants and 592 non-bitterants, which is distinct from the fully or partially hypothetical non-bitterant dataset used in the previous works. Based on this experimental dataset, we harness the consensus votes from the multiple machine-learning methods (e.g., deep learning etc.) combined with the molecular fingerprint to build the bitter/bitterless classification models with five-fold cross-validation, which are further inspected by the Y-randomization test and applicability domain analysis. One of the best consensus models affords the accuracy, precision, specificity, sensitivity, F1-score, and Matthews correlation coefficient (MCC) of 0.929, 0.918, 0.898, 0.954, 0.936, and 0.856 respectively on our test set. For the automatic prediction of bitterant, a graphic program “e-Bitter” is developed for the convenience of users via the simple mouse click. To our best knowledge, it is for the first time to adopt the consensus model for the bitterant prediction and develop the first free stand-alone software for the experimental food scientist.

Physiological Effects of Enriched Environment Exposure and LTP Induction in the Hippocampus In Vivo Do Not Transfer Faithfully to In Vitro Slices

ERIC Educational Resources Information Center

Eckert, Michael J.; Abraham, Wickliffe C.

2010-01-01

A number of experimental paradigms use in vitro brain slices to test for changes in synaptic transmission and plasticity following a behavioral manipulation. For example, a number of previous studies have reported a variety of effects of environmental enrichment (EE) exposure on field potential responses in hippocampal slices, but in no study was…

[Learning to use semiautomatic external defibrillators through audiovisual materials for schoolchildren].

PubMed

Jorge-Soto, Cristina; Abelairas-Gómez, Cristian; Barcala-Furelos, Roberto; Gregorio-García, Carolina; Prieto-Saborit, José Antonio; Rodríguez-Núñez, Antonio

2016-01-01

To assess the ability of schoolchildren to use a automated external defibrillator (AED) to provide an effective shock and their retention of the skill 1 month after a training exercise supported by audiovisual materials. Quasi-experimental controlled study in 205 initially untrained schoolchildren aged 6 to 16 years old. SAEDs were used to apply shocks to manikins. The students took a baseline test (T0) of skill, and were then randomized to an experimental or control group in the first phase (T1). The experimental group watched a training video, and both groups were then retested. The children were tested in simulations again 1 month later (T2). A total of 196 students completed all 3 phases. Ninety-six (95.0%) of the secondary school students and 54 (56.8%) of the primary schoolchildren were able to explain what a SAED is. Twenty of the secondary school students (19.8%) and 8 of the primary schoolchildren (8.4%) said they knew how to use one. At T0, 78 participants (39.8%) were able to simulate an effective shock. At T1, 36 controls (34.9%) and 56 experimental-group children (60.2%) achieved an effective shock (P< .001). At T2, 53 controls (51.4%) and 61 experimental-group children (65.6%) gave effective shocks (P=.045). All the students completed the tests in 120 seconds. Their average times decreased with each test. The secondary school students achieved better results. Previously untrained secondary school students know what a AED is and half of them can manage to use one in simulations. Brief narrative, audiovisual instruction improves students' skill in managing a SAED and helps them retain what they learned for later use.

Semantically enabled and statistically supported biological hypothesis testing with tissue microarray databases

PubMed Central

2011-01-01

Background Although many biological databases are applying semantic web technologies, meaningful biological hypothesis testing cannot be easily achieved. Database-driven high throughput genomic hypothesis testing requires both of the capabilities of obtaining semantically relevant experimental data and of performing relevant statistical testing for the retrieved data. Tissue Microarray (TMA) data are semantically rich and contains many biologically important hypotheses waiting for high throughput conclusions. Methods An application-specific ontology was developed for managing TMA and DNA microarray databases by semantic web technologies. Data were represented as Resource Description Framework (RDF) according to the framework of the ontology. Applications for hypothesis testing (Xperanto-RDF) for TMA data were designed and implemented by (1) formulating the syntactic and semantic structures of the hypotheses derived from TMA experiments, (2) formulating SPARQLs to reflect the semantic structures of the hypotheses, and (3) performing statistical test with the result sets returned by the SPARQLs. Results When a user designs a hypothesis in Xperanto-RDF and submits it, the hypothesis can be tested against TMA experimental data stored in Xperanto-RDF. When we evaluated four previously validated hypotheses as an illustration, all the hypotheses were supported by Xperanto-RDF. Conclusions We demonstrated the utility of high throughput biological hypothesis testing. We believe that preliminary investigation before performing highly controlled experiment can be benefited. PMID:21342584

Peer Led Team Learning in Introductory Biology: Effects on Peer Leader Critical Thinking Skills

PubMed Central

Snyder, Julia J.; Wiles, Jason R.

2015-01-01

This study evaluated hypothesized effects of the Peer-Led Team Learning (PLTL) instructional model on undergraduate peer leaders’ critical thinking skills. This investigation also explored peer leaders’ perceptions of their critical thinking skills. A quasi-experimental pre-test/post-test with control group design was used to determine critical thinking gains in PLTL/non-PLTL groups. Critical thinking was assessed using the California Critical Thinking Skills Test (CCTST) among participants who had previously completed and been successful in a mixed-majors introductory biology course at a large, private research university in the American Northeast. Qualitative data from open-ended questionnaires confirmed that factors thought to improve critical thinking skills such as interaction with peers, problem solving, and discussion were perceived by participants to have an impact on critical thinking gains. However, no significant quantitative differences in peer leaders’ critical thinking skills were found between pre- and post-experience CCTST measurements or between experimental and control groups. PMID:25629311

Peer led team learning in introductory biology: effects on peer leader critical thinking skills.

PubMed

Snyder, Julia J; Wiles, Jason R

2015-01-01

This study evaluated hypothesized effects of the Peer-Led Team Learning (PLTL) instructional model on undergraduate peer leaders' critical thinking skills. This investigation also explored peer leaders' perceptions of their critical thinking skills. A quasi-experimental pre-test/post-test with control group design was used to determine critical thinking gains in PLTL/non-PLTL groups. Critical thinking was assessed using the California Critical Thinking Skills Test (CCTST) among participants who had previously completed and been successful in a mixed-majors introductory biology course at a large, private research university in the American Northeast. Qualitative data from open-ended questionnaires confirmed that factors thought to improve critical thinking skills such as interaction with peers, problem solving, and discussion were perceived by participants to have an impact on critical thinking gains. However, no significant quantitative differences in peer leaders' critical thinking skills were found between pre- and post-experience CCTST measurements or between experimental and control groups.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barnhill, William C.; Gao, Hong; Kheireddin, Bassem

We have previously reported an oil-miscible phosphonium-organophosphate ionic liquid (IL) with an effective anti-wear (AW) functionality when added to a base oil by itself or combined with a conventional zinc dialkyldithiophosphate (ZDDP) for a synergistic effect. In this research, we investigated whether this synergy manifests in formulated engine oils. An experimental SAE 0W-16 engine oil was generated containing a combination of IL and ZDDP with equal phosphorus contribution. The prototype engine oil was first evaluated using tribological bench tests: AW performance in boundary lubrication (BL) and friction behavior (Stribeck curves) in elastohydrodynamic, mixed, and BL. In addition, the forthcoming standardmore » Sequence VIE engine dynamometer test was then conducted to demonstrate improved fuel economy. Results were benchmarked against those of another experimental engine oil with almost the same formulation except using ZDDP only without the IL (similar total phosphorus content). The IL-ZDDP formulation consistently outperforms the ZDDP-only formulation in friction reduction and wear protection, and results from the bench and engine tests are well correlated.« less

Antinociceptive, anti-inflammatory and antipyretic properties of Melastoma malabathricum leaves aqueous extract in experimental animals.

PubMed

Zakaria, Z A; Raden Mohd Nor, R N S; Hanan Kumar, G; Abdul Ghani, Z D F; Sulaiman, M R; Rathna Devi, G; Mat Jais, A M; Somchit, M N; Fatimah, C A

2006-12-01

The present study was carried out to establish the antinociceptive, anti-inflammatory, and antipyretic properties of the aqueous extract of Melastoma malabathricum leaves in experimental animals. The antinociceptive activity was measured using abdominal constriction, hot-plate, and formalin tests, whereas the anti-inflammatory and antipyretic activities were measured using carrageenan-induced paw edema and brewer's yeast-induced pyrexia tests, respectively. The extract, which was obtained after soaking the air-dried leaves in distilled water for 72 h and then preparing in concentrations of 10%, 50%, and 100% (v/v), was administered subcutaneously 30 min prior to subjection to the above mentioned assays. At all concentrations tested, the extract was found to exhibit significant (P < 0.05) antinociceptive, anti-inflammatory, and antipyretic activities in a concentration-independent manner. Our findings that the aqueous extract of M. malabathricum possesses antinociceptive, anti-inflammatory, and antipyretic activities supports previous claims on its traditional uses to treat various ailments.

Engine-Scale Combustor Rig Designed, Fabricated, and Tested for Combustion Instability Control Research

NASA Technical Reports Server (NTRS)

DeLaat, John C.; Breisacher, Kevin J.

2000-01-01

Low-emission combustor designs are prone to combustor instabilities. Because active control of these instabilities may allow future combustors to meet both stringent emissions and performance requirements, an experimental combustor rig was developed for investigating methods of actively suppressing combustion instabilities. The experimental rig has features similar to a real engine combustor and exhibits instabilities representative of those in aircraft gas turbine engines. Experimental testing in the spring of 1999 demonstrated that the rig can be tuned to closely represent an instability observed in engine tests. Future plans are to develop and demonstrate combustion instability control using this experimental combustor rig. The NASA Glenn Research Center at Lewis Field is leading the Combustion Instability Control program to investigate methods for actively suppressing combustion instabilities. Under this program, a single-nozzle, liquid-fueled research combustor rig was designed, fabricated, and tested. The rig has many of the complexities of a real engine combustor, including an actual fuel nozzle and swirler, dilution cooling, and an effusion-cooled liner. Prior to designing the experimental rig, a survey of aircraft engine combustion instability experience identified an instability observed in a prototype engine as a suitable candidate for replication. The frequency of the instability was 525 Hz, with an amplitude of approximately 1.5-psi peak-to-peak at a burner pressure of 200 psia. The single-nozzle experimental combustor rig was designed to preserve subcomponent lengths, cross sectional area distribution, flow distribution, pressure-drop distribution, temperature distribution, and other factors previously found to be determinants of burner acoustic frequencies, mode shapes, gain, and damping. Analytical models were used to predict the acoustic resonances of both the engine combustor and proposed experiment. The analysis confirmed that the test rig configuration and engine configuration had similar longitudinal acoustic characteristics, increasing the likelihood that the engine instability would be replicated in the rig. Parametric analytical studies were performed to understand the influence of geometry and condition variations and to establish a combustion test plan. Cold-flow experiments verified that the design values of area and flow distributions were obtained. Combustion test results established the existence of a longitudinal combustion instability in the 500-Hz range with a measured amplitude approximating that observed in the engine. Modifications to the rig configuration during testing also showed the potential for injector independence. The research combustor rig was developed in partnership with Pratt & Whitney of West Palm Beach, Florida, and United Technologies Research Center of East Hartford, Connecticut. Experimental testing of the combustor rig took place at United Technologies Research Center.

Influence of the strain path on crash properties of a crash-box structure by experimental and numerical approaches

NASA Astrophysics Data System (ADS)

Durrenberger, L.; Even, D.; Molinari, A.; Rusinek, A.

2006-08-01

In order to reduce the gas emission without decreasing the passengers safety, the UHSS (Ultra High Strength Steel) steels are more and more used in the automotive industry. The very high mechanical characteristics of these steels allow to reduce the car weight thanks to the thickness reduction of the structure parts. The aim of this study is to analyse the plastic pre-strain effect (forming) on the crash properties of a crash-box structure. In order to achieve this goal, experimental rheological tests have been performed by combining quasi-static tensile tests followed by dynamic tensile test (8.10 - 3 s - 1 ≤ dot{\\varepsilon} ≤ 1000 s - 1) for a TRIP steel produced by ARCELOR. The combination of these results allows to obtain a better understanding of the steel behaviour in dynamic loading under different strain paths. All these information are necessary for an efficient simulation of crash test by including a pertinent material response. A special attention is given to the influence of the previous forming process on the dynamical response of crash boxes.

Modeling and Simulation of the Second-Generation Orion Crew Module Air Bag Landing System

NASA Technical Reports Server (NTRS)

Timmers, Richard B.; Welch, Joseph V.; Hardy, Robin C.

2009-01-01

Air bags were evaluated as the landing attenuation system for earth landing of the Orion Crew Module (CM). An important element of the air bag system design process is proper modeling of the proposed configuration to determine if the resulting performance meets requirements. Analysis conducted to date shows that airbags are capable of providing a graceful landing of the CM in nominal and off-nominal conditions such as parachute failure, high horizontal winds, and unfavorable vehicle/ground angle combinations. The efforts presented here surround a second generation of the airbag design developed by ILC Dover, and is based on previous design, analysis, and testing efforts. In order to fully evaluate the second generation air bag design and correlate the dynamic simulations, a series of drop tests were carried out at NASA Langley's Landing and Impact Research (LandIR) facility. The tests consisted of a full-scale set of air bags attached to a full-scale test article representing the Orion Crew Module. The techniques used to collect experimental data, construct the simulations, and make comparisons to experimental data are discussed.

Inelastic deformation and damage at high temperature

NASA Astrophysics Data System (ADS)

Krempl, E.

1992-06-01

Combined experimental and theoretical investigations into the inelastic deformation and damage behavior of engineering alloys at elevated temperatures are being pursued. The analysis of previously performed strain rate change and relaxation tests on modified 9Cr-1Mo steel showed the need for inclusion of a recovery of state term in the growth laws for the state variables of the viscoplasticity theory based on overstress (VBO). Recovery of state terms were introduced and the experimental results were satisfactorily simulated. The finite deformation theory of VBO has been developed further to include a convected derivative rationale for the choice of the objective stress rate. The reversing direct current voltage drop measurements during low cycle fatigue at elevated temperature were improved. A passive filter bank and new positioning devices for the coils were installed. Tests at 650 C and lasting several days showed excessive, uncontrollable temperature changes. It was decided to drop the test temperature to 538 C which is close to the operating temperature of type 304 stainless steel. The temperature fluctuations in torsion tests were within +/- 3 C which was considered satisfactory.

Heisenberg's error-disturbance relations: A joint measurement-based experimental test

NASA Astrophysics Data System (ADS)

Zhao, Yuan-Yuan; Kurzyński, Paweł; Xiang, Guo-Yong; Li, Chuan-Feng; Guo, Guang-Can

2017-04-01

The original Heisenberg error-disturbance relation was recently shown to be not universally valid and two different approaches to reformulate it were proposed. The first one focuses on how the error and disturbance of two observables A and B depend on a particular quantum state. The second one asks how a joint measurement of A and B affects their eigenstates. Previous experiments focused on the first approach. Here we focus on the second one. First, we propose and implement an extendible method of quantum-walk-based joint measurements of noisy Pauli operators to test the error-disturbance relation for qubits introduced in the work of Busch et al. [Phys. Rev. A 89, 012129 (2014), 10.1103/PhysRevA.89.012129], where the polarization of the single photon, corresponding to a walker's auxiliary degree of freedom that is commonly known as a coin, undergoes a position- and time-dependent evolution. Then we formulate and experimentally test a universally valid state-dependent relation for three mutually unbiased observables. We therefore establish a method of testing error-disturbance relations.

Calcic amphiboles in calc-alkaline and alkaline magmas: thermobarometric and chemometric empirical equations valid up to 1,130°C and 2.2 GPa

NASA Astrophysics Data System (ADS)

Ridolfi, Filippo; Renzulli, Alberto

2012-05-01

The following article presents constraints of the stability of Mg-rich (Mg/(Mg + Fe2+) > 0.5) calcic amphibole in both calc-alkaline and alkaline magmas, testing of previous thermobarometers, and formulation of new empirical equations that take into consideration a large amount of literature data (e.g. more than one thousand amphibole compositions among experimental and natural crystals). Particular care has been taken in choosing a large number of natural amphiboles and selecting quality experimental data from literature. The final database of experimental data, composed of 61 amphiboles synthesized in the ranges of 800-1,130°C and 130-2,200 MPa, indicates that amphibole crystallization occurs in a horn-like P- T stability field limited by two increasing curves (i.e. the thermal stability and an upper limit), which should start to bend back to higher pressures. Among calcic amphiboles, magnesiohornblendes and tschermakitic pargasites are only found in equilibrium with calc-alkaline melts and crystallize at relatively shallow conditions ( P up to ~1 GPa). Kaersutite and pargasite are species almost exclusively found in alkaline igneous products, while magnesiohastingsite is equally distributed in calc-alkaline and alkaline rocks. The reliability of previous amphibole applications was checked using the selected experimental database. The results of this testing indicate that none of the previous thermobarometers can be successfully used to estimate the P, T and fO2 in a wide range of amphibole crystallization conditions. Multivariate least-square analyses of experimental amphibole compositions and physico-chemical parameters allowed us to achieve a new thermobarometric model that gives reasonably low uncertainties ( T ± 23.5°C, P ± 11.5%, H2Omelt ± 0.78wt%) for calc-alkaline and alkaline magmas in a wide range of P- T conditions (up to 1,130°C and 2,200 MPa) and ΔNNO values (±0.37 log units) up to 500 MPa. The AK-[4]Al relation in amphibole can be readily used to distinguish crystals of calc-alkaline liquids from those of alkaline magmas. In addition, several chemometric equations allowing to estimate the anhydrous composition of the melts in equilibrium with amphiboles of calc-alkaline magmas were derived.

Discrete Element Modeling (DEM) of Triboelectrically Charged Particles: Revised Experiments

NASA Technical Reports Server (NTRS)

Hogue, Michael D.; Calle, Carlos I.; Curry, D. R.; Weitzman, P. S.

2008-01-01

In a previous work, the addition of basic screened Coulombic electrostatic forces to an existing commercial discrete element modeling (DEM) software was reported. Triboelectric experiments were performed to charge glass spheres rolling on inclined planes of various materials. Charge generation constants and the Q/m ratios for the test materials were calculated from the experimental data and compared to the simulation output of the DEM software. In this paper, we will discuss new values of the charge generation constants calculated from improved experimental procedures and data. Also, planned work to include dielectrophoretic, Van der Waals forces, and advanced mechanical forces into the software will be discussed.

Water walking - an evolution of water surface skipping

NASA Astrophysics Data System (ADS)

Hurd, Randy; Belden, Jesse; Jandron, Michael; Bower, Allan; Holekamp, Sean; Truscott, Tadd

2017-11-01

Previous work has shown that elastomeric spheres skip more easily than disk-shaped stones. This is due to increased lift stemming from sphere deformation, which provides an increased cross-sectional area and favorable attack angle upon impact. We extend lift models developed for individual impacts to long-range multiple impact events and compare the estimates to experimental results, which show good agreement. Additionally, a surprising new mode of skipping is observed that resembles water-walking, wherein a quickly rotating sphere produces small successive impacts allowing it to move parallel to the water surface. The dynamics of this new multiple skip behavior are rationalized analytically and tested experimentally.

Reversible Data Hiding Based on DNA Computing

PubMed Central

Xie, Yingjie

2017-01-01

Biocomputing, especially DNA, computing has got great development. It is widely used in information security. In this paper, a novel algorithm of reversible data hiding based on DNA computing is proposed. Inspired by the algorithm of histogram modification, which is a classical algorithm for reversible data hiding, we combine it with DNA computing to realize this algorithm based on biological technology. Compared with previous results, our experimental results have significantly improved the ER (Embedding Rate). Furthermore, some PSNR (peak signal-to-noise ratios) of test images are also improved. Experimental results show that it is suitable for protecting the copyright of cover image in DNA-based information security. PMID:28280504

Experimental study of the condensation heat transfer characteristics of CO2 in a horizontal microfin tube with a diameter of 4.95 mm

NASA Astrophysics Data System (ADS)

Son, Chang-Hyo; Oh, Hoo-Kyu

2012-11-01

The condensation heat transfer characteristics for CO2 flowing in a horizontal microfin tube were investigated by experiment with respect to condensation temperature and mass flux. The test section consists of a 2,400 mm long horizontal copper tube of 4.6 mm inner diameter. The experiments were conducted at refrigerant mass flux of 400-800 kg/m2s, and saturation temperature of 20-30 °C. The main experimental results showed that annular flow was highly dominated the majority of condensation flow in the horizontal microfin tube. The condensation heat transfer coefficient increases with decreasing saturation temperature and increasing mass flux. The experimental data were compared against previous heat transfer correlations. Most correlations failed to predict the experimental data. However, the correlation by Cavallini et al. showed relatively good agreement with experimental data in the microfin tube. Therefore, a new condensation heat transfer correlation is proposed with mean and average deviations of 3.14 and -7.6 %, respectively.

Imperfection Insensitivity Analyses of Advanced Composite Tow-Steered Shells

NASA Technical Reports Server (NTRS)

Wu, K. Chauncey; Farrokh, Babak; Stanford, Bret K.; Weaver, Paul M.

2016-01-01

Two advanced composite tow-steered shells, one with tow overlaps and another without overlaps, were previously designed, fabricated and tested in end compression, both without cutouts, and with small and large cutouts. In each case, good agreement was observed between experimental buckling loads and supporting linear bifurcation buckling analyses. However, previous buckling tests and analyses have shown historically poor correlation, perhaps due to the presence of geometric imperfections that serve as failure initiators. For the tow-steered shells, their circumferential variation in axial stiffness may have suppressed this sensitivity to imperfections, leading to the agreement noted between tests and analyses. To investigate this further, a numerical investigation was performed in this study using geometric imperfections measured from both shells. Finite element models of both shells were analyzed first without, and then, with measured imperfections that were then, superposed in different orientations around the shell longitudinal axis. Small variations in both the axial prebuckling stiffness and global buckling load were observed for the range of imperfections studied here, which suggests that the tow steering, and resulting circumferentially varying axial stiffness, may result in the test-analysis correlation observed for these shells.

AOTV bow shock location

NASA Technical Reports Server (NTRS)

Desautel, D.

1985-01-01

Hypersonic bow-shock location and geometry are of central importance to the aerodynamics and aerothermodynamics of aeroassisted orbital transfer vehicles (AOTVs), but they are difficult to predict for a given vehicle configuration. This paper reports experimental measurements of shock standoff distance for the 70 deg cone AOTV configuration in shock-tunnel-test flows at Mach numbers of 3.8 to 7.9 and for angles of attack from 0 deg to 20 deg. The controlling parameter for hypersonic bow-shock standoff distance (for a given forebody shape) is the mean normal-shock density ratio. Values for this parameter in the tests reported are in the same range as those of the drag-brake AOTV perigee regime. Results for standoff distance are compared with those previously reported in the literature for this AOTV configuration. It is concluded that the AOTV shock standoff distance for the conical configuration, based on frustrum (base) radius, is equivalent to that of a sphere with a radius about 35 percent greater than that of the cone; the distance is, therefore, much less than reported in previous studies. Some reasons for the discrepancies between the present and previous are advanced. The smaller standoff distance determined here implies there will be less radiative heat transfer than was previously expected.

Periodic flow hydrodynamic resistance parameters for woven screen matrices at cryogenic temperatures

NASA Astrophysics Data System (ADS)

Perrella, M. D.; Ghiaasiaan, S. M.

2017-12-01

The regenerator is a critical component in all Stirling and Pulse Tube cryocoolers. It generally consists of a microporous metallic or rare-earth filler material contained within a cylindrical shell. Accurate modelling of the hydrodynamic and thermal behaviour of different regenerator materials is crucial to the successful design of cryogenic systems. Previous investigations have used experimental measurements at steady and periodic flow conditions in conjunction with pore-level CFD analysis to determine the pertinent hydrodynamic parameters, namely the Darcy permeability and Forchheimer coefficients. Due to the difficulty associated with experimental measurement at cryogenic temperatures, past investigations were mostly performed at ambient conditions and their results are assumed to be appropriate for cryogenic temperatures. In this study, a regenerator filled with woven screen matrices such as 400 mesh T316 stainless steel were assembled and experimentally tested under periodic helium flow at cryogenic temperatures. The mass flow and pressure drop data were analysed using CFD to determine the dimensionless friction factor, Darcy Permeability and Forchheimer coefficients. These results are compared to previous investigations at ambient temperature conditions, and the relevance of room-temperature models and correlations to cryogenic temperatures is critically assessed.

Design, Construction, and Test of a 473 MHZ Four - Cavity Rfq.

NASA Astrophysics Data System (ADS)

Kazimi, Reza

1992-01-01

An RFQ accelerator using the new four-rod cavity design has been fabricated and successfully tested at Texas Accelerator Center. The RFQ is designed to accelerate a 10 mA H^- ion beam from 30 keV to 500 keV with the operating frequency of 473 MHz. This new type of RFQ structure not only promises simplicity of design, construction, and operation, but also can be manufactured to operate at higher frequencies than previously achieved by other four-rod type RFQs. Combination of simplicity and compactness due to higher operating frequencies (400 to 500 MHz) makes the design desirable for injector of proton accelerators, medical linear accelerators, and variety of other applications. This dissertation presents the steps I went through in inventing, developing, and experimentally testing this new RFQ design. First an introduction to accelerators is given, and the basic accelerator physics terminologies are defined. The principles of operations of the RFQs are described, and the theory behind new type of RFQ structure is explained. Then the beam dynamics and cavity design of the RFQ are presented. Finally, the mechanical design and construction procedure are discussed, and experimental results of rf tests and actual H ^- beam test are given.

Improving GPU-accelerated adaptive IDW interpolation algorithm using fast kNN search.

PubMed

Mei, Gang; Xu, Nengxiong; Xu, Liangliang

2016-01-01

This paper presents an efficient parallel Adaptive Inverse Distance Weighting (AIDW) interpolation algorithm on modern Graphics Processing Unit (GPU). The presented algorithm is an improvement of our previous GPU-accelerated AIDW algorithm by adopting fast k-nearest neighbors (kNN) search. In AIDW, it needs to find several nearest neighboring data points for each interpolated point to adaptively determine the power parameter; and then the desired prediction value of the interpolated point is obtained by weighted interpolating using the power parameter. In this work, we develop a fast kNN search approach based on the space-partitioning data structure, even grid, to improve the previous GPU-accelerated AIDW algorithm. The improved algorithm is composed of the stages of kNN search and weighted interpolating. To evaluate the performance of the improved algorithm, we perform five groups of experimental tests. The experimental results indicate: (1) the improved algorithm can achieve a speedup of up to 1017 over the corresponding serial algorithm; (2) the improved algorithm is at least two times faster than our previous GPU-accelerated AIDW algorithm; and (3) the utilization of fast kNN search can significantly improve the computational efficiency of the entire GPU-accelerated AIDW algorithm.

Facilitating the learning process: a pilot study of collaborative testing vs individualistic testing in the chiropractic college setting.

PubMed

Meseke, Jamie K; Nafziger, Rita; Meseke, Christopher A

2008-05-01

This pilot study examines the effect collaborative testing has on achievement of students taking a basic science course at a chiropractic college. The grades of 2 cohorts of students taking a basic science course were compared: the control group from the first academic term (n = 73) and the experimental group from the second academic term (n = 41). The control cohort completed weekly quizzes as individuals. The experimental cohort completed the weekly quizzes in small collaborative groups. All unit examinations and the final examination were taken by both cohorts individually. Grades for each cohort were derived from 6 weekly unit quizzes, 3 unit examinations, and a comprehensive final examination. Overall, the experimental group differed from the control group (Wilks' Lambda = 0.318; F(10,103) = 22.052; and P < .001). All quiz scores were significantly higher for the experimental group as compared with the control group. In addition, overall point totals and final course grades also differed significantly. No significant differences, however, were observed in either the first 2 unit examination scores or the final examination scores. These results confirm previous reports that student performance is enhanced by collaborative learning. Collaborative testing provided students with the opportunity to discuss their reasoning and receive immediate feedback from other group members regarding their rationale, which potentially enhanced understanding of course material. Students were encouraged to become more active in the course as group discussions emerged from individual perspectives. The collaborative learning process may enhance critical thinking abilities, which are vital for future chiropractic practitioners.

Modelling mass transfer during venting/soil vapour extraction: Non-aqueous phase liquid/gas mass transfer coefficient estimation

NASA Astrophysics Data System (ADS)

Esrael, D.; Kacem, M.; Benadda, B.

2017-07-01

We investigate how the simulation of the venting/soil vapour extraction (SVE) process is affected by the mass transfer coefficient, using a model comprising five partial differential equations describing gas flow and mass conservation of phases and including an expression accounting for soil saturation conditions. In doing so, we test five previously reported quations for estimating the non-aqueous phase liquid (NAPL)/gas initial mass transfer coefficient and evaluate an expression that uses a reference NAPL saturation. Four venting/SVE experiments utilizing a sand column are performed with dry and non-saturated sand at low and high flow rates, and the obtained experimental results are subsequently simulated, revealing that hydrodynamic dispersion cannot be neglected in the estimation of the mass transfer coefficient, particularly in the case of low velocities. Among the tested models, only the analytical solution of a convection-dispersion equation and the equation proposed herein are suitable for correctly modelling the experimental results, with the developed model representing the best choice for correctly simulating the experimental results and the tailing part of the extracted gas concentration curve.

Experimental findings on actinide recovery utilizing oxidation by peroxydisulfate followed by ion exchange: Fuel cycle research & development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hobbs, D. T.; Shehee, T. C.

2015-08-31

Our research seeks to determine if inorganic ion-exchange materials can be exploited to provide effective minor actinide (Am, Cm) separation from lanthanides. Previous work has established that a number of inorganic and UMOF ion-exchange materials exhibit varying affinities for actinides and lanthanides, which may be exploited for effective separations. During FY15, experimental work focused on investigating methods to oxidize americium in dilute nitric and perchloric acid with subsequent ion-exchange performance measurements of ion exchangers with the oxidized americium in dilute nitric acid. Ion-exchange materials tested included a variety of alkali titanates. Americium oxidation testing sought to determine the influence thatmore » other redox active components may have on the oxidation of Am III. Experimental findings indicated that Ce III, Np V, and Ru II are oxidized by peroxydisulfate, but there are no indications that the presence of Ce III, Np V, and Ru II affected the rate or extent of americium oxidation at the concentrations of peroxydisulfate being used.« less

Experimental clean combustor program: Noise study

NASA Technical Reports Server (NTRS)

Sofrin, T. G.; Riloff, N., Jr.

1976-01-01

Under a Noise Addendum to the NASA Experimental Clean Combustor Program (ECCP) internal pressure fluctuations were measured during tests of JT9D combustor designs conducted in a burner test rig. Measurements were correlated with burner operating parameters using an expression relating farfield noise to these parameters. For a given combustor, variation of internal noise with operating parameters was reasonably well predicted by this expression but the levels were higher than farfield predictions and differed significantly among several combustors. For two burners, discharge stream temperature fluctuations were obtained with fast-response thermocouples to allow calculation of indirect combustion noise which would be generated by passage of the temperature inhomogeneities through the high pressure turbine stages of a JT9D turbofan engine. Using a previously developed analysis, the computed indirect combustion noise was significantly lower than total low frequency core noise observed on this and several other engines.

No Association between Oxytocin Receptor (OXTR) Gene Polymorphisms and Experimentally Elicited Social Preferences

PubMed Central

Apicella, Coren L.; Cesarini, David; Johannesson, Magnus; Dawes, Christopher T.; Lichtenstein, Paul; Wallace, Björn; Beauchamp, Jonathan; Westberg, Lars

2010-01-01

Background Oxytocin (OXT) has been implicated in a suite of complex social behaviors including observed choices in economic laboratory experiments. However, actual studies of associations between oxytocin receptor (OXTR) gene variants and experimentally elicited social preferences are rare. Methodology/Principal Findings We test hypotheses of associations between social preferences, as measured by behavior in two economic games, and 9 single nucleotide polymorphisms (SNPs) of the OXTR gene in a sample of Swedish twins (n = 684). Two standard economic games, the dictator game and the trust game, both involving real monetary consequences, were used to elicit such preferences. After correction for multiple hypothesis testing, we found no significant associations between any of the 9 single nucleotide polymorphisms (SNPs) and behavior in either of the games. Conclusion We were unable to replicate the most significant association reported in previous research between the amount donated in a dictator game and an OXTR genetic variant. PMID:20585395

No association between oxytocin receptor (OXTR) gene polymorphisms and experimentally elicited social preferences.

PubMed

Apicella, Coren L; Cesarini, David; Johannesson, Magnus; Dawes, Christopher T; Lichtenstein, Paul; Wallace, Björn; Beauchamp, Jonathan; Westberg, Lars

2010-06-16

Oxytocin (OXT) has been implicated in a suite of complex social behaviors including observed choices in economic laboratory experiments. However, actual studies of associations between oxytocin receptor (OXTR) gene variants and experimentally elicited social preferences are rare. We test hypotheses of associations between social preferences, as measured by behavior in two economic games, and 9 single nucleotide polymorphisms (SNPs) of the OXTR gene in a sample of Swedish twins (n = 684). Two standard economic games, the dictator game and the trust game, both involving real monetary consequences, were used to elicit such preferences. After correction for multiple hypothesis testing, we found no significant associations between any of the 9 single nucleotide polymorphisms (SNPs) and behavior in either of the games. We were unable to replicate the most significant association reported in previous research between the amount donated in a dictator game and an OXTR genetic variant.

Mach 4 Performance of a Fixed-Geometry Hypersonic Inlet with Rectangular-to-Elliptical Shape Transition

NASA Technical Reports Server (NTRS)

Smart, Michael K.; Trexler, Carl A.

2003-01-01

Wind-tunnel testing of a hypersonic inlet with rectangular-to-elliptical shape transition has been conducted at Mach 4.0. These tests were performed to investigate the starting and back-pressure limits of this fixed-geometry inlet at conditions well below the Mach 5.7 design point. Results showed that the inlet required side spillage holes in order to self-start at Mach 4.0. Once started, the inlet generated a compression ratio of 12.6, captured almost 80% of available air and withstood a back-pressure ratio of 30.3 relative to tunnel static pressure. The spillage penalty for self-starting was estimated to be 4% of available air. These experimental results, along with previous experimental results at Mach 6.2 indicate that fixed-geometry inlets with rectangular-to-elliptical shape transition are a viable configuration for airframe- integrated scramjets that operate over a significant Mach number range.

Activity of cationically substituted bis-benzimidazoles against experimental Pneumocystis carinii pneumonia.

PubMed Central

Tidwell, R R; Jones, S K; Naiman, N A; Berger, L C; Brake, W B; Dykstra, C C; Hall, J E

1993-01-01

On the basis of a previously observed correlation between the antimicrobial activity and DNA binding strength of dicationic molecules, a series of 10 dicationically substituted bis-benzimidazoles were tested for activity in the rat model of Pneumocystis carinii pneumonia. One of the compounds, 1,4-bis[5-(2-imidazolinyl)-2-benzimidazolyl]butane, was found to be more potent and less toxic than pentamidine. PMID:8215291

Detection of in-plane displacements of acoustic wave fields using extrinsic Fizeau fiber interferometric sensors

NASA Technical Reports Server (NTRS)

Dhawan, R.; Gunther, M. F.; Claus, R. O.

1991-01-01

Quantitative measurements of the in-plane particle displacement components of ultrasonic surface acoustic wave fields using extrinsic Fizeau fiber interferometric (EFFI) sensors are reported. Wave propagation in materials and the fiber sensor elements are briefly discussed. Calibrated experimental results obtained for simulated acoustic emission events on homogeneous metal test specimens are reported and compared to previous results obtained using piezoelectric transducers.

Performance and Pollution Measurements of Two-Row Swirl-Can Combustor Having 72 Modules

NASA Technical Reports Server (NTRS)

Biaglow, James A.; Trout, Arthur M.

1975-01-01

A test program was conducted to evaluate the performance and gaseous-pollutant levels of an experimental full-annulus 72-module swirl-can combustor. A comparison of data with those for a 120-module swirl-can combustor showed no significant difference in performance or levels of gaseous pollutants. Oxides of nitrogen were correlated for the 72- and 120-swirl-can combustors by using a previously developed parameter.

Discharge Chamber Primary Electron Modeling Activities in Three-Dimensions

NASA Technical Reports Server (NTRS)

Steuber, Thomas J.

2004-01-01

Designing discharge chambers for ion thrusters involves many geometric configuration decisions. Various decisions will impact discharge chamber performance with respect to propellant utilization efficiency, ion production costs, and grid lifetime. These hardware design decisions can benefit from the assistance of computational modeling. Computational modeling for discharge chambers has been limited to two-dimensional codes that leveraged symmetry for interpretation into three-dimensional analysis. This paper presents model development activities towards a three-dimensional discharge chamber simulation to aid discharge chamber design decisions. Specifically, of the many geometric configuration decisions toward attainment of a worthy discharge chamber, this paper focuses on addressing magnetic circuit considerations with a three-dimensional discharge chamber simulation as a tool. With this tool, candidate discharge chamber magnetic circuit designs can be analyzed computationally to gain insight into factors that may influence discharge chamber performance such as: primary electron loss width in magnetic cusps, cathode tip position with respect to the low magnetic field volume, definition of a low magnetic field region, and maintenance of a low magnetic field region across the grid span. Corroborating experimental data will be obtained from mockup hardware tests. Initially, simulated candidate magnetic circuit designs will resemble previous successful thruster designs. To provide opportunity to improve beyond previous performance benchmarks, off-design modifications will be simulated and experimentally tested.

Tribological characterization of TiCN coatings deposited by two crossed laser ablation plasma beams

NASA Astrophysics Data System (ADS)

Camps, Enrique; Escobar-Alarcón, L.; Camps, Iván; Muhl, Stephen; Flores, Martín

2013-03-01

The simultaneous laser ablation of two targets (graphite and titanium) in an Ar-N2 gas mixture was carried out to deposit thin films of the ternary compound TiCN at room temperature. The base conditions used to produce the TiN without carbon were taken from our previous studies. The experimental conditions for the ablation of the carbon target were varied so that the carbon content in the films could be changed depending on the carbon ion energy. The control of the experimental conditions was carried out using a Langmuir planar probe which permitted the determination of the mean kinetic ion energy. The maximum hardness value of 35 GPa, was obtained with a carbon ion energy of about 250 eV, which corresponds to a film with 5 at% carbon content. In order to perform tribological and scratch tests, two types of substrate were used: nitrided AISI 316 stainless steel and AISI 316 stainless steel previously coated with a thin titanium layer (˜50 nm). Values of the wear rate in the range of 1.39×10-6 to 7.45×10-5 mm3 N-1 m-1, friction coefficient from 0.21 to 0.28 and adhesion from scratch test measurements up to 80 N for final critical load, were obtained.

Classroom intervention to change peers' attitudes towards children who stutter: A feasibility study.

PubMed

Kathard, Harsha; Walters, Freda; Frieslaar, Kareemah; Mhlongo, Thembeka; Rhoode, Melissa; Shaboodien, Raeesa; Weidmann, Julia; Zimmerman, Nicole; Zoetmulder, Amy; Camroodien-Surve, Fatemah

2014-12-03

Before interventions are implemented, the potential treatment benefit must be determined. The primary objective of this feasibility study was to assess if peers' attitudes towards children who stutter (CWS) change one month after the administration of the Classroom Communication Resource (CCR). The secondary objectives of the study were to determine if differences in peer attitudes were related to gender and to previous exposure to a person who stutters. The study used a cluster randomised control trial design. The study included 211 Grade 7 participants from schools in the Cape Town Metropole. The CCR intervention was administered to 97 participants in the experimental group, whilst 114 participants in the control group did not receive the intervention. The Stuttering Resource Outcome Measure(SROM) used as the outcome measure during pre- and post-test period. STATISTICA was used for in-depth data analysis. An overall positive direction of change in scores was observed for the experimental group compared with the control group. However, the magnitude of change in the experimental group was not statistically significant (p = 0.2683). Male and female participants did not differ significantly in their scores on the SROM across pre-test and post-test periods. Participants who had exposure to individuals who stutter had significantly more positive scores on the SROM in the pre-test and post-test periods compared to those who had no direct exposure to stuttering. This result indicated the beginning of positive attitude change which may be attributed to the intervention. Further investigation is warranted.

Test program to provide confidence in liquid oxygen cooling of hydrocarbon fueled rocket thrust chambers

NASA Technical Reports Server (NTRS)

Armstrong, E. S.

1986-01-01

An experimental program has been planned at the NASA Lewis Research Center to build confidence in the feasibility of liquid oxygen cooling for hydrocarbon fueled rocket engines. Although liquid oxygen cooling has previously been incorporated in test hardware, more runtime is necessary to gain confidence in this concept. In the previous tests, small oxygen leaks developed at the throat of the thrust chamber and film cooled the hot-gas side of the chamber wall without resulting in catastrophic failure. However, more testing is necessary to demonstrate that a catastrophic failure would not occur if cracks developed further upstream between the injector and the throat, where the boundary layer has not been established. Since under normal conditions cracks are expected to form in the throat region of the thrust chamber, cracks must be initiated artificially in order to control their location. Several methods of crack initiation are discussed in this report. Four thrust chambers, three with cracks and one without, should be tested. The axial location of the cracks should be varied parametrically. Each chamber should be instrumented to determine the effects of the cracks, as well as the overall performance and durability of the chambers.

Achieving Tier 4 Emissions in Biomass Cookstoves

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marchese, Anthony; DeFoort, Morgan; Gao, Xinfeng

Previous literature on top-lit updraft (TLUD) gasifier cookstoves suggested that these stoves have the potential to be the lowest emitting biomass cookstove. However, the previous literature also demonstrated a high degree of variability in TLUD emissions and performance, and a lack of general understanding of the TLUD combustion process. The objective of this study was to improve understanding of the combustion process in TLUD cookstoves. In a TLUD, biomass is gasified and the resulting producer gas is burned in a secondary flame located just above the fuel bed. The goal of this project is to enable the design of amore » more robust TLUD that consistently meets Tier 4 performance targets through a better understanding of the underlying combustion physics. The project featured a combined modeling, experimental and product design/development effort comprised of four different activities: Development of a model of the gasification process in the biomass fuel bed; Development of a CFD model of the secondary combustion zone; Experiments with a modular TLUD test bed to provide information on how stove design, fuel properties, and operating mode influence performance and provide data needed to validate the fuel bed model; Planar laser-induced fluorescence (PLIF) experiments with a two-dimensional optical test bed to provide insight into the flame dynamics in the secondary combustion zone and data to validate the CFD model; Design, development and field testing of a market ready TLUD prototype. Over 180 tests of 40 different configurations of the modular TLUD test bed were performed to demonstrate how stove design, fuel properties and operating mode influences performance, and the conditions under which Tier 4 emissions are obtainable. Images of OH and acetone PLIF were collected at 10 kHz with the optical test bed. The modeling and experimental results informed the design of a TLUD prototype that met Tier 3 to Tier 4 specifications in emissions and Tier 2 in efficiency. The final prototype was field tested in India.« less

Counteracting moment device for reduction of earthquake-induced excursions of multi-level buildings.

PubMed

Nagaya, K; Fukushima, T; Kosugi, Y

1999-05-01

A vibration-control mechanism for beams and columns was presented in our previous report in which the earthquake force was transformed into a vibration-control force by using a gear train mechanism. In our previous report, however, only the principle of transforming the earthquake force into the control force was presented; the discussion for real structures and the design method were not presented. The present article provides a theoretical analysis of the column which is used in multi-layered buildings. Experimental tests were carried out for a model of multi-layered buildings in the frequency range of a principal earthquake wave. Theoretical results are compared to the experimental data. The optimal design of the control mechanism, which is of importance in the column design, is presented. Numerical calculations are carried out for the optimal design. It is shown that vibrations of the column involving the mechanism are suppressed remarkably. The optimal design method and the analytical results are applicable to the design of the column.

Aerodynamic Characteristics of Two Waverider-Derived Hypersonic Cruise Configurations

NASA Technical Reports Server (NTRS)

Cockrell, Charles E., Jr.; Huebner, Lawrence D.; Finley, Dennis B.

1996-01-01

An evaluation was made on the effects of integrating the required aircraft components with hypersonic high-lift configurations known as waveriders to create hypersonic cruise vehicles. Previous studies suggest that waveriders offer advantages in aerodynamic performance and propulsion/airframe integration (PAI) characteristics over conventional non-waverider hypersonic shapes. A wind-tunnel model was developed that integrates vehicle components, including canopies, engine components, and control surfaces, with two pure waverider shapes, both conical-flow-derived waveriders for a design Mach number of 4.0. Experimental data and limited computational fluid dynamics (CFD) solutions were obtained over a Mach number range of 1.6 to 4.63. The experimental data show the component build-up effects and the aerodynamic characteristics of the fully integrated configurations, including control surface effectiveness. The aerodynamic performance of the fully integrated configurations is not comparable to that of the pure waverider shapes, but is comparable to previously tested hypersonic models. Both configurations exhibit good lateral-directional stability characteristics.

Comparisons of Mixed-Phase Icing Cloud Simulations with Experiments Conducted at the NASA Propulsion Systems Laboratory

NASA Technical Reports Server (NTRS)

Bartkus, Tadas; Tsao, Jen-Ching; Struk, Peter

2017-01-01

This paper builds on previous work that compares numerical simulations of mixed-phase icing clouds with experimental data. The model couples the thermal interaction between ice particles and water droplets of the icing cloud with the flowing air of an icing wind tunnel for simulation of NASA Glenn Research Centers (GRC) Propulsion Systems Laboratory (PSL). Measurements were taken during the Fundamentals of Ice Crystal Icing Physics Tests at the PSL tunnel in March 2016. The tests simulated ice-crystal and mixed-phase icing that relate to ice accretions within turbofan engines.

Regeneratively cooled rocket engine for space storable propellants

NASA Technical Reports Server (NTRS)

Wagner, W. R.

1973-01-01

Analysis, design, fabrication, and test efforts were performed for the existing OF2/B2H6 regeneratively cooled lK (4448 N) thrust chamber to illustrate simultaneous B2H6 fuel and OF2 oxidizer cooling and to provide results for a gaseous propellant condition injected into the combustion chamber. Data derived from performance, thermal and flow measurements confirmed predictions derived from previous test work and from concurrent analytical study. Development data derived from the experimental study were indicated to be sufficient to develop a preflight thrust chamber demonstrator prototype for future space mission objectives.

Analysis of the OPERA 15-pin experiment with SABRE-2P. [LMFBR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rose, S.D.; Carbajo, J.J.

The OPERA (Out-of-Pile Expulsion and Reentry Apparatus) experiment simulates the initial phase of a pump coastdown without scram of a liquid-metal fast breeder reactor, specifically the Fast Flux Test Facility. The test section is a 15-pin 60/sup 0/ triangular sector designed to simulate a full-size 61-pin hexagonal bundle. A previous study indicates this to be an adequate simulation. In this paper, experimental results from the OPERA 15-pin experiment performed at ANL in 1982 are compared to analytical calculations obtained with the SABRE-2P code at ORNL.

Friction losses in a lubricated thrust-loaded cageless angular-contract bearing

NASA Technical Reports Server (NTRS)

Townsend, D. P.; Allen, C. W.; Zaretsky, E. V.

1973-01-01

The NASA spinning torque apparatus was modified to measure the spinning torque on a cageless ball thrust bearing. Friction torque was measured for thrust loads varying from 44.5 to 403 newtons (10 to 90 lb) at speeds of 1000, 2000, and 3000 rpm. Tests were conducted with di-2-ethylhexyl sebacate and a synthetic paraffinic oil. These tests were run with either oil jet lubrication or with a thin surface film of lubricant only. An analytical model which included rolling resistance was developed and extended from previous models for spinning torque and lubricant rheology. The model was extended by the inclusion of rolling resistance. The computed values were in fair agreement with the experimental results and confirmed previous hypotheses that a thin lubricant film gives minimum bearing torque and an oil jet flow of a viscous lubricant will result in considerable rolling torque in addition to the torque due to ball spin.

Interaction Between a Steady Detonation Wave in Nitromethane and Geometrical Complex Confinement Defects

NASA Astrophysics Data System (ADS)

Crouzet, B.; Soulard, L.; Carion, N.; Manczur, P.

2007-12-01

Two copper cylinder expansion tests were carried out on nitromethane. They differ from the classical cylinder test in that the liner includes evenly-spaced protruding circular defects. The aim is to study how a detonation front propagating in the liquid explosive interacts with the confining material defects. The subsequent motion of the metal, accelerated by the expanding detonation products, is measured using a range of diagnostic techniques: electrical probes, a rapid framing camera, a glass block associated with a streak camera and velocity laser interferometers. The different experimental records have been examined in the light of previous classical cylinder test measurements, simple 2D theoretical shock polar analysis results and 2D numerical simulations.

The Lateral Stability of Equal-flanged Aluminum-alloy I-beams Subjected to Pure Bending

NASA Technical Reports Server (NTRS)

Dumont, C; Hill, H N

1940-01-01

Equal-flange beams of a special extruded I-section of 27ST aluminum alloy were tested in pure bending. Complete end fixity was not attained. Loading was continued until a definite maximum value had been reached. Tensile tests were made on specimens cut from the flanges and the web of each beam. Compressive stress-strain characteristics were determined by pack compression tests on specimens cut from the flanges. Values computed from an equation previously suggested by one of the authors for the critical stress at which such beams become unstable were found to be in good agreement with values computed from experimentally determined critically bending moments.

A new UK fission yield evaluation UKFY3.7

NASA Astrophysics Data System (ADS)

Mills, Robert William

2017-09-01

The JEFF neutron induced and spontaneous fission product yield evaluation is currently unchanged from JEFF-3.1.1, also known by its UK designation UKFY3.6A. It is based upon experimental data combined with empirically fitted mass, charge and isomeric state models which are then adjusted within the experimental and model uncertainties to conform to the physical constraints of the fission process. A new evaluation has been prepared for JEFF, called UKFY3.7, that incorporates new experimental data and replaces the current empirical models (multi-Gaussian fits of mass distribution and Wahl Zp model for charge distribution combined with parameter extrapolation), with predictions from GEF. The GEF model has the advantage that one set of parameters allows the prediction of many different fissioning nuclides at different excitation energies unlike previous models where each fissioning nuclide at a specific excitation energy had to be fitted individually to the relevant experimental data. The new UKFY3.7 evaluation, submitted for testing as part of JEFF-3.3, is described alongside initial results of testing. In addition, initial ideas for future developments allowing inclusion of new measurements types and changing from any neutron spectrum type to true neutron energy dependence are discussed. Also, a method is proposed to propagate uncertainties of fission product yields based upon the experimental data that underlies the fission yield evaluation. The covariance terms being determined from the evaluated cumulative and independent yields combined with the experimental uncertainties on the cumulative yield measurements.

Cold Flow Plume Entrainment Test Final Report NTF Test Number 2456

NASA Technical Reports Server (NTRS)

Ruf, Joseph H.; McDaniels, David; Mishtawy, Jason; Ramachandran, Narayanan; Hammad, Khaled J.

2005-01-01

As part of the Space Shuttle Return to Flight (RTF) program, Marshall Space Flight Center (MSFC) performed computational fluid dynamics (CFD) analysis to define the velocity flowfields around the Shuttle stack at liftoff. These CFD predicted velocity flowfields were used in debris transport analysis (DTA). High speed flows such as plumes induce or 'entrain' mass from the surrounding environment. Previous work had shown that CFD analysis over-predicts plume induced flows. Therefore, the DTA would tend to 1) predict more debris impacts, and 2) the debris velocity (and kinetic energy) of those impacts would be too high. At a November, 2004 peer-review it was recommended that the Liftoff DTA team quantify the uncertainty in the DTA caused by the CFD's over prediction of plume induced flow. To do so, the Liftoff DTA team needed benchmark quality data for plume induced flow to quantify the CFD accuracy and its effect on the DTA. MSFC's Nozzle Test Facility (NTF) conducted the "Nozzle Induced Flows test, P#2456" to obtain experimental data for plume induced flows for nozzle flow exhausting into q quiescent freestream. Planning for the test began in December, 2004 and the experimental data was obtained in February and March of 2005. The funding for this test was provided by MSFC's Space Shuttle Propulsion Systems Integration and Engineering office.

Once-through integral system (OTIS): Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gloudemans, J R

1986-09-01

A scaled experimental facility, designated the once-through integral system (OTIS), was used to acquire post-small break loss-of-coolant accident (SBLOCA) data for benchmarking system codes. OTIS was also used to investigate the application of the Abnormal Transient Operating Guidelines (ATOG) used in the Babcock and Wilcox (B and W) designed nuclear steam supply system (NSSS) during the course of an SBLOCA. OTIS was a single-loop facility with a plant to model power scale factor of 1686. OTIS maintained the key elevations, approximate component volumes, and loop flow resistances, and simulated the major component phenomena of a B and W raised-loop nuclearmore » plant. A test matrix consisting of 15 tests divided into four categories was performed. The largest group contained 10 tests and was defined to parametrically obtain an extensive set of plant-typical experimental data for code benchmarking. Parameters such as leak size, leak location, and high-pressure injection (HPI) shut-off head were individually varied. The remaining categories were specified to study the impact of the ATOGs (2 tests), to note the effect of guard heater operation on observed phenomena (2 tests), and to provide a data set for comparison with previous test experience (1 test). A summary of the test results and a detailed discussion of Test 220100 is presented. Test 220100 was the nominal or reference test for the parametric studies. This test was performed with a scaled 10-cm/sup 2/ leak located in the cold leg suction piping.« less

Application of Stereo PIV on a Supersonic Parachute Model

NASA Technical Reports Server (NTRS)

Wernet, Mark P.; Locke, Randy J.; Wroblewski, Adam; Sengupta, Anita

2009-01-01

The Mars Science Laboratory (MSL) is the next step in NASA's Mars Exploration Program, currently scheduled for 2011. The spacecraft's descent into the Martian atmosphere will be slowed from Mach 2 to subsonic speeds via a large parachute system with final landing under propulsive control. A Disk-Band-Gap (DBG) parachute will be used on MSL similar to the designs that have been used on previous missions, however; the DBG parachute used by MSL will be larger (21.5 m) than in any of the previous missions due to the weight of the payload and landing site requirements. The MSL parachute will also deploy at higher Mach number (M 2) than previous parachutes, which can lead to instabilities in canopy performance. Both the increased size of the DBG above previous demonstrated configurations and deployment at higher Mach numbers add uncertainty to the deployment, structural integrity and performance of the parachute. In order to verify the performance of the DBG on MSL, experimental testing, including acquisition of Stereo Particle Imaging Velocimetry (PIV) measurements were required for validating CFD predictions of the parachute performance. A rigid model of the DBG parachute was tested in the 10x10 foot wind tunnel at GRC. Prior to the MSL tests, a PIV system had never been used in the 10x10 wind tunnel. In this paper we discuss some of the technical challenges overcome in implementing a Stereo PIV system with a 750x400 mm field-of-view in the 10x10 wind tunnel facility and results from the MSL hardshell canopy tests.

Mechanochemical Symmetry Breaking in Hydra Aggregates

PubMed Central

Mercker, Moritz; Köthe, Alexandra; Marciniak-Czochra, Anna

2015-01-01

Tissue morphogenesis comprises the self-organized creation of various patterns and shapes. Although detailed underlying mechanisms are still elusive in many cases, an increasing amount of experimental data suggests that chemical morphogen and mechanical processes are strongly coupled. Here, we develop and test a minimal model of the axis-defining step (i.e., symmetry breaking) in aggregates of the Hydra polyp. Based on previous findings, we combine osmotically driven shape oscillations with tissue mechanics and morphogen dynamics. We show that the model incorporating a simple feedback loop between morphogen patterning and tissue stretch reproduces a wide range of experimental data. Finally, we compare different hypothetical morphogen patterning mechanisms (Turing, tissue-curvature, and self-organized criticality). Our results suggest the experimental investigation of bigger (i.e., multiple head) aggregates as a key step for a deeper understanding of mechanochemical symmetry breaking in Hydra. PMID:25954896

Experimental test of entangled histories

NASA Astrophysics Data System (ADS)

Cotler, Jordan; Duan, Lu-Ming; Hou, Pan-Yu; Wilczek, Frank; Xu, Da; Yin, Zhang-Qi; Zu, Chong

2017-12-01

Entangled histories arise when a system partially decoheres in such a way that its past cannot be described by a sequence of states, but rather a superposition of sequences of states. Such entangled histories have not been previously observed. We propose and demonstrate the first experimental scheme to create entangled history states of the Greenberger-Horne-Zeilinger (GHZ) type. In our experiment, the polarization states of a single photon at three different times are prepared as a GHZ entangled history state. We define a GHZ functional which attains a maximum value 1 on the ideal GHZ entangled history state and is bounded above by 1 / 16 for any three-time history state lacking tripartite entanglement. We have measured the GHZ functional on a state we have prepared experimentally, yielding a value of 0 . 656 ± 0 . 005, clearly demonstrating the contribution of entangled histories.

Modeling and experimental study on near-field acoustic levitation by flexural mode.

PubMed

Liu, Pinkuan; Li, Jin; Ding, Han; Cao, Wenwu

2009-12-01

Near-field acoustic levitation (NFAL) has been used in noncontact handling and transportation of small objects to avoid contamination. We have performed a theoretical analysis based on nonuniform vibrating surface to quantify the levitation force produced by the air film and also conducted experimental tests to verify our model. Modal analysis was performed using ANSYS on the flexural plate radiator to obtain its natural frequency of desired mode, which is used to design the measurement system. Then, the levitation force was calculated as a function of levitation distance based on squeeze gas film theory using measured amplitude and phase distributions on the vibrator surface. Compared with previous fluid-structural analyses using a uniform piston motion, our model based on the nonuniform radiating surface of the vibrator is more realistic and fits better with experimentally measured levitation force.

Hovering Dual-Spin Vehicle Groundwork for Bias Momentum Sizing Validation Experiment

NASA Technical Reports Server (NTRS)

Rothhaar, Paul M.; Moerder, Daniel D.; Lim, Kyong B.

2008-01-01

Angular bias momentum offers significant stability augmentation for hovering flight vehicles. The reliance of the vehicle on thrust vectoring for agility and disturbance rejection is greatly reduced with significant levels of stored angular momentum in the system. A methodical procedure for bias momentum sizing has been developed in previous studies. This current study provides groundwork for experimental validation of that method using an experimental vehicle called the Dual-Spin Test Device, a thrust-levitated platform. Using measured data the vehicle's thrust vectoring units are modeled and a gust environment is designed and characterized. Control design is discussed. Preliminary experimental results of the vehicle constrained to three rotational degrees of freedom are compared to simulation for a case containing no bias momentum to validate the simulation. A simulation of a bias momentum dominant case is presented.

Theoretical and Experimental Estimations of Volumetric Inductive Phase Shift in Breast Cancer Tissue

NASA Astrophysics Data System (ADS)

González, C. A.; Lozano, L. M.; Uscanga, M. C.; Silva, J. G.; Polo, S. M.

2013-04-01

Impedance measurements based on magnetic induction for breast cancer detection has been proposed in some studies. This study evaluates theoretical and experimentally the use of a non-invasive technique based on magnetic induction for detection of patho-physiological conditions in breast cancer tissue associated to its volumetric electrical conductivity changes through inductive phase shift measurements. An induction coils-breast 3D pixel model was designed and tested. The model involves two circular coils coaxially centered and a human breast volume centrally placed with respect to the coils. A time-harmonic numerical simulation study addressed the effects of frequency-dependent electrical properties of tumoral tissue on the volumetric inductive phase shift of the breast model measured with the circular coils as inductor and sensor elements. Experimentally; five female volunteer patients with infiltrating ductal carcinoma previously diagnosed by the radiology and oncology departments of the Specialty Clinic for Women of the Mexican Army were measured by an experimental inductive spectrometer and the use of an ergonomic inductor-sensor coil designed to estimate the volumetric inductive phase shift in human breast tissue. Theoretical and experimental inductive phase shift estimations were developed at four frequencies: 0.01, 0.1, 1 and 10 MHz. The theoretical estimations were qualitatively in agreement with the experimental findings. Important increments in volumetric inductive phase shift measurements were evident at 0.01MHz in theoretical and experimental observations. The results suggest that the tested technique has the potential to detect pathological conditions in breast tissue associated to cancer by non-invasive monitoring. Further complementary studies are warranted to confirm the observations.

Methodology of Blade Unsteady Pressure Measurement in the NASA Transonic Flutter Cascade

NASA Technical Reports Server (NTRS)

Lepicovsky, J.; McFarland, E. R.; Capece, V. R.; Jett, T. A.; Senyitko, R. G.

2002-01-01

In this report the methodology adopted to measure unsteady pressures on blade surfaces in the NASA Transonic Flutter Cascade under conditions of simulated blade flutter is described. The previous work done in this cascade reported that the oscillating cascade produced waves, which for some interblade phase angles reflected off the wind tunnel walls back into the cascade, interfered with the cascade unsteady aerodynamics, and contaminated the acquired data. To alleviate the problems with data contamination due to the back wall interference, a method of influence coefficients was selected for the future unsteady work in this cascade. In this approach only one blade in the cascade is oscillated at a time. The majority of the report is concerned with the experimental technique used and the experimental data generated in the facility. The report presents a list of all test conditions for the small amplitude of blade oscillations, and shows examples of some of the results achieved. The report does not discuss data analysis procedures like ensemble averaging, frequency analysis, and unsteady blade loading diagrams reconstructed using the influence coefficient method. Finally, the report presents the lessons learned from this phase of the experimental effort, and suggests the improvements and directions of the experimental work for tests to be carried out for large oscillation amplitudes.

Calibrated dilatometer exercise to probe thermoplastic properties of coal in pressurized CO 2

DOE PAGES

Romanov, Vyacheslav N.; Lynn, Ronald J.; Warzinski, Robert P.

2017-07-03

This research was aimed at testing a hypothesis, that at elevated CO 2 pressure coal can soften at temperatures well below those obtained in the presence of other gases. That could have serious negative implications for injection of CO 2 into deep coal seams. Here, we have examined the experimental design issues and procedures used in the previously published studies, and experimentally investigated the physical behavior of a similar coal in the presence of CO 2 as a function of pressure and temperature, using the same high-pressure micro-dilatometer refurbished and carefully calibrated for this purpose. No notable reduction in coalmore » softening temperature was observed in this study.« less

Calibrated dilatometer exercise to probe thermoplastic properties of coal in pressurized CO 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Romanov, Vyacheslav N.; Lynn, Ronald J.; Warzinski, Robert P.

This research was aimed at testing a hypothesis, that at elevated CO 2 pressure coal can soften at temperatures well below those obtained in the presence of other gases. That could have serious negative implications for injection of CO 2 into deep coal seams. Here, we have examined the experimental design issues and procedures used in the previously published studies, and experimentally investigated the physical behavior of a similar coal in the presence of CO 2 as a function of pressure and temperature, using the same high-pressure micro-dilatometer refurbished and carefully calibrated for this purpose. No notable reduction in coalmore » softening temperature was observed in this study.« less

Theoretical and experimental study of a fiber optic microphone

NASA Technical Reports Server (NTRS)

Hu, Andong; Cuomo, Frank W.; Zuckerwar, Allan J.

1992-01-01

Modifications to condenser microphone theory yield new expressions for the membrane deflections at its center, which provide the basic theory for the fiber optic microphone. The theoretical analysis for the membrane amplitude and the phase response of the fiber optic microphone is given in detail in terms of its basic geometrical quantities. A relevant extension to the original concepts of the optical microphone includes the addition of a backplate with holes similar in design to present condenser microphone technology. This approach generates improved damping characteristics and extended frequency response that were not previously considered. The construction and testing of the improved optical fiber microphone provide experimental data that are in good agreement with the theoretical analysis.

Experimental Study of Heat Transfer to Small Cylinders in a Subsonic, High-temperature Gas Stream

NASA Technical Reports Server (NTRS)

Glawe, George E; Johnson, Robert C

1957-01-01

A Nusselt-Reynolds number relation for cylindrical thermocouple wires in crossflow was obtained from the experimental determination of time constants. Tests were conducted in exhaust gas over a temperature range of 2000 to 3400 R, a Mach number range of 0.3 to 0.8, and a static-pressure range from 2/3 to 1-1/3 atmospheres, yielding a Reynolds number range of 450 to 3000. The correlation obtained is Nu=(0.428 plus or minus 0.003) times the square root of Re* with average deviations of a single observation of 8.5 percent. This relation is the same as one previously reported for room-temperature conditions.

KSC-02pd0027

NASA Image and Video Library

2002-01-17

KENNEDY SPACE CENTER, FLA. -- Workers in the Vertical Processing Facility look over the Near Infrared Camera and Multi-Object Spectrometer (NICMOS) Cooling System, part of the payload on mission STS-109, the Hubble Servicing Telescope Mission. NICMOS is a new experimental cooling system consisting of a compressor and tiny turbines. With the experimental cryogenic system, NASA hopes to re-cool the infrared detectors to below -315 degrees F (-193 degrees Celsius). NICMOS II was previously tested aboard STS-95 in 1998. It could extend the life of the Hubble Space Telescope by several years. Astronauts aboard Columbia on mission STS-109 will be replacing the original NICMOS with the newer version. Launch of mission STS-109 is scheduled for Feb. 28, 2002

KSC-02pd0028

NASA Image and Video Library

2002-01-17

KENNEDY SPACE CENTER, FLA. -- A closeup view of the Near Infrared Camera and Multi-Object Spectrometer (NICMOS) Cooling System, part of the payload on mission STS-109, the Hubble Servicing Telescope Mission. NICMOS II is a new experimental cooling system consisting of a compressor and tiny turbines. With the experimental cryogenic system, NASA hopes to re-cool the infrared detectors to below -315 degrees F (-193 degrees Celsius). NICMOS II was previously tested aboard STS-95 in 1998. It could extend the life of the Hubble Space Telescope by several years. Astronauts aboard Columbia on mission STS-109 will be replacing the original NICMOS with the newer version. Launch of mission STS-109 is scheduled for Feb. 28, 2002

Are patients with chronic pruritus more susceptible to social stress than healthy controls? An experimental case-control-study.

PubMed

Schneider, G; Stumpf, A; Burgmer, M; Broecker, P; Volmering, L; Ständer, S

2018-05-10

Previous research suggests associations between stress and pruritus in population samples and in patients with atopic dermatitis (AD) but research is lacking for patients with chronic pruritus (CP) of other origin. We therefore investigated acute and chronic stress levels and physiological stress measures (i.e. heart rate variability HRV) of CP and HC. We expected higher levels of chronic stress and of acute stress in a standardized experimental stress test in CP, which should be also reflected by differences in the stress sensitive HRV parameters. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Experimental Research into Noise Emission of A Gear Micropump with Plastic Rotor

NASA Astrophysics Data System (ADS)

Rodionov, L. V.; Rekadze, P. D.

2018-01-01

The previous researches show that it’s possible to replace several parts of gear pump to plastic ones. This substitution leads to cost and noise reduction of the pump. Therefore, the series of acoustic experiments on a test bench were carry-out. Sound pressure levels were recorded with microphone, located in a pipe made of a vacuum rubber. Conducted experiment shows that acoustic characteristics of the micropump depend on the different material of driven rotor. Experimental result indicates that the proposed measures for replacing metal rotor to plastic one reduce micropump noise on the studied modes. The maximum achieved acoustic efficiency on equivalent level is 11 dB.

A high-speed photography study of cavitation in a dynamically loaded journal bearing

NASA Technical Reports Server (NTRS)

Sun, D. C.; Brewe, D. E.

1990-01-01

The earlier study made by Jacobson and Hamrock on the cavitation of liquid lubricant films in a dynamically loaded journal bearing was repeated with a quartz sleeve, which was more rigid than the Polymethylmethacrylate (PMMA) sleeve used previously. Various improvements of the test rig were made concomitantly so that the experimental errors could be better controlled and assessed. The updated speed photography experiment and its results are described.

A high speed photography study of cavitation in a dynamically loaded journal bearing

NASA Technical Reports Server (NTRS)

Sun, D. C.; Brewe, D. E.

1991-01-01

The earlier study made by Jacobson and Hamrock on the cavitation of liquid lubricant films in a dynamically loaded journal bearing was repeated with a quartz sleeve, which was more rigid than the Polymethylmethacrylate (PMMA) sleeve used previously. Various improvements of the test rig were made concomitantly so that the experimental errors could be better controlled and assessed. The updated speed photography experiment and its results are described.

High intensity acoustic tests of a thermally stressed aluminum plate in TAFA

NASA Technical Reports Server (NTRS)

Ng, Chung Fai; Clevenson, Sherman A.

1989-01-01

An investigation was conducted in the Thermal Acoustic Fatigue Apparatus at the Langley Research Center to study the acoustically excited random motion of an aluminum plate which is buckled due to thermal stresses. The thermal buckling displacements were measured and compared with theory. The general trends of the changes in resonances frequencies and random responses of the plate agree with previous theoretical prediction and experimental results for a mechanically buckled plate.

Verification of Accelerated Testing Methodology for Long-Term Durability of CFRP Laminates for Marine Use

DTIC Science & Technology

2012-01-30

CFRP LAMINATES FOR MARINE USE Sa. CONTRACT NUMBER 5b. GRANT NUMBER N00014-06-1-1139 Sc. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Miyano, Yasushi...prediction of CFRP laminates proposed and confirmed experimentally in the previous ONR project of Grant # N000140110949 was verified theoretically and refined...DURABILITY OF CFRP LAMINATES FOR MARINE USE Principal Investigator Yasushi Miyano Co-principal Investigator Isao Kimpara Materials System

Dual-Mode Scramjet Combustor: Numerical Sensitivity and Evaluation of Experiments

DTIC Science & Technology

2012-01-01

effects of the air gap; the second took into account the effects of the air gap by using a backpressure imposed boundary condition. Figure 36 shows an... exhauster housing at the exit of the combustor in RC22’s test apparatus. I. Introduction Previous experimental efforts in...amount of air/fuel mixing, which affects combustion . Other approaches such as Large-Eddy Simulation (LES) and Direct-Numerical Simulation (DNS) are too

The protective effects of free wheel-running against cocaine psychomotor sensitization persist after exercise cessation in C57BL/6J mice.

PubMed

Lespine, L-F; Tirelli, E

2015-12-03

Previous literature suggests that free access to a running wheel can attenuate the behavioral responsiveness to addictive drugs in rodents. In a few studies, wheel-running cessation accentuated drug responsiveness. Here, we tested whether free wheel-running cessation is followed by (1) an accentuation or (2) an attenuation of cocaine psychomotor sensitization, knowing that no cessation of (continuous) wheel-running is associated with an attenuation of cocaine responsiveness. Male C57BL/6J mice, aged 35 days, were housed singly either with (exercising mice) or without (non-exercising mice) a running wheel. At the end of a period of 36 days, half of the exercising mice were deprived of their wheel whereas the other half of exercising mice kept their wheel until the end of experimentation (which lasted 85 days). The non-exercising mice were housed without wheel throughout experimentation. Testing took place 3 days after exercise cessation. After 2 once-daily drug-free test sessions, mice were tested for initiation of psychomotor sensitization over 13 once-daily injections of 8 mg/kg cocaine. Post-sensitization conditioned activation (saline challenge) and long-term expression of sensitization were assessed 2 or 30 days after the last sensitizing injection (same treatments as for initiation of sensitization), respectively. Exercising mice and mice undergoing wheel-running cessation exhibited comparable degrees of attenuation of all cocaine effects in comparison with the continuously non-exercising mice, which showed the greatest effects. Thus, the efficaciousness of wheel-running at attenuating cocaine sensitization not only resisted to exercise cessation but was also unambiguously persistent (an important effect rarely reported in previous literature). Copyright © 2015 IBRO. Published by Elsevier Ltd. All rights reserved.

Academic Achievement from Using the Learning Medium Via a Tablet Device Based on Multiple Intelligences in Grade 1 Elementary Student.

PubMed

Nuallaong, Winitra; Nuallaong, Thanya; Preechadirek, Nongluck

2015-04-01

To measure academic achievement of the multiple intelligence-based learning medium via a tablet device. This is a quasi-experimental research study (non-randomized control group pretest-posttest design) in 62 grade 1 elementary students (33 males and 29 females). Thirty-one students were included in an experimental group using purposive sampling by choosing a student who had highest multiple intelligence test scores in logical-mathematic. Then, this group learned by the new learning medium via a tablet which the application matched to logical-mathematic multiple intelligence. Another 31 students were included in a control group using simple random sampling and then learning by recitation. Both groups did pre-test and post-test vocabulary. Thirty students in the experimental group and 24 students in the control group increased post-test scores (odds ratio = 8.75). Both groups made significant increasing in post-test scores. The experimental group increased 9.07 marks (95% CI 8.20-9.93) significantly higher than the control group which increased 4.39 marks (95% CI 3.06-5.72) (t = -6.032, df = 51.481, p < 0.001). Although learning from either multiple intelligence-based learning medium via a tablet or recitation can contribute academic achievement, learningfrom the new medium contributed more achievement than recitation. The new learning medium group had higher post-test scores 8.75 times than the recitation group. Therefore, the new learning medium is more effective than the traditional recitation in terms of academic achievement. This study has limitations because samples came from the same school. However, the previous study in Thailand did notfind a logical-mathematical multiple intelligence difference among schools. In the future, long-term research to find how the new learning medium affects knowledge retention will support the advantage for life-long learning.

Evaporation heat transfer of carbon dioxide at low temperature inside a horizontal smooth tube

NASA Astrophysics Data System (ADS)

Yoon, Jung-In; Son, Chang-Hyo; Jung, Suk-Ho; Jeon, Min-Ju; Yang, Dong-Il

2017-05-01

In this paper, the evaporation heat transfer coefficient of carbon dioxide at low temperature of -30 to -20 °C in a horizontal smooth tube was investigated experimentally. The test devices consist of mass flowmeter, pre-heater, magnetic gear pump, test section (evaporator), condenser and liquid receiver. Test section is made of cooper tube. Inner and outer diameter of the test section is 8 and 9.52 mm, respectively. The experiment is conducted at mass fluxes from 100 to 300 kg/m2 s, saturation temperature from -30 to -20 °C. The main results are summarized as follows: In case that the mass flux of carbon dioxide is 100 kg/m2 s, the evaporation heat transfer coefficient is almost constant regardless of vapor quality. In case of 200 and 300 kg/m2 s, the evaporation heat transfer coefficient increases steadily with increasing vapor quality. For the same mass flux, the evaporation heat transfer coefficient increases as the evaporation temperature of the refrigerant decreases. In comparison of heat transfer correlations with the experimental result, the evaporation heat transfer correlations do not predict them exactly. Therefore, more accurate heat transfer correlation than the previous one is required.

Performance of pervious pavement parking bays storing rainwater in the north of Spain.

PubMed

Gomez-Ullate, E; Bayon, J R; Coupe, S; Castro-Fresno, D

2010-01-01

Pervious pavements are drainage techniques that improve urban water management in a sustainable manner. An experimental pervious pavement parking area has been constructed in the north of Spain (Santander), with the aim of harvesting good quality rainwater. Forty-five pervious pavement structures have been designed and constructed to measure stored water quantity and quality simultaneously. Ten of these structures are specifically constructed with different geotextile layers for improving water storage within the pavements. Following the confirmation in previous laboratory experiments that the geotextile influenced on water storage, two different geosynthetics (Inbitex and a One Way evaporation control membrane) and control pervious pavements with no geotextile layers were tested in the field. Weather conditions were monitored in order to find correlations with the water storage within the pervious pavement models tested. During one year of monitoring the three different pervious pavement types tested remained at their maximum storage capacity. The heavy rain events which occurred during the experimental period caused evaporation rates within the pervious pavements to be not significant, but allowed the researchers to observe certain trends in the water storage. Temperature was the most closely correlated weather factor with the level of the water stored within the pervious pavements tested.

Investigation of the Non-Isothermal Convective Mixing of Turbulent, Round, Wall Jets

NASA Astrophysics Data System (ADS)

Kristo, Paul; Kimber, Mark

2017-11-01

The wall jet has become a paradigm for geometrically bounded flows due to the intrinsically difficult nature of the advection promoted by the geometry of the jet, coupled with prompt diffusion from the adjacent wall. Previous experimental investigations have sought to characterize the hydraulic and thermal behavior of such flows, however the physics promoted by parallel coplanar round jets has received inadequate experimental attention. The current effort is comprised of three parallel, coplanar, equidistant round jets issuing vertically downward into a pseudo-unconfined test section. The outer diameters of the jets are placed tangentially along a smooth flat plate. Non-intrusive optical techniques are incorporated for both hydraulic and thermal observations. Preliminary tests provide accurate inlet boundary conditions for each case. Reference metrics are captured during testing to account for ambient effects and readings inside of the test section. By varying the velocity and temperature inlet parameters, insights are drawn regarding the effects on the merging point (MP) and combined point (CP) of both the flow and thermal fields. Velocity fields in the plane normal to the wall yield additional insight into the deceleration caused by dissipation from both the plate and surrounding stagnant fluid.

Tribological bench and engine dynamometer tests of a low viscosity SAE 0W-16 engine oil using a combination of ionic liquid and ZDDP as anti-wear additives

DOE PAGES

Barnhill, William C.; Gao, Hong; Kheireddin, Bassem; ...

2015-09-29

We have previously reported an oil-miscible phosphonium-organophosphate ionic liquid (IL) with an effective anti-wear (AW) functionality when added to a base oil by itself or combined with a conventional zinc dialkyldithiophosphate (ZDDP) for a synergistic effect. In this research, we investigated whether this synergy manifests in formulated engine oils. An experimental SAE 0W-16 engine oil was generated containing a combination of IL and ZDDP with equal phosphorus contribution. The prototype engine oil was first evaluated using tribological bench tests: AW performance in boundary lubrication (BL) and friction behavior (Stribeck curves) in elastohydrodynamic, mixed, and BL. In addition, the forthcoming standardmore » Sequence VIE engine dynamometer test was then conducted to demonstrate improved fuel economy. Results were benchmarked against those of another experimental engine oil with almost the same formulation except using ZDDP only without the IL (similar total phosphorus content). The IL-ZDDP formulation consistently outperforms the ZDDP-only formulation in friction reduction and wear protection, and results from the bench and engine tests are well correlated.« less

The Anomalous Magnetic Moment of the Muon

NASA Astrophysics Data System (ADS)

Hughes, Vernon W.; Sichtermann, Ernst P.

2002-12-01

A precise measurement of the anomalous g value, a = (g - 2)/2, for the positive muon has been made at the Brookhaven Alternating Gradient Synchrotron. The result aμ+ = 11 659 202(14)(6) × 10-10 (1.3 ppm) is in good agreement with previous measurements and has an error one third that of the combined previous data. The measurement tests standard theory and has the potential to discover new physics. The analysis of data collected in 2000 and 2001 is well underway and, when combined with data from a requested and final run in the fall of 2002 and winter of 2003, are expected to reduce the experimental uncertainty on aμ to 0.4 ppm.

High Power Hall Thrusters

NASA Technical Reports Server (NTRS)

Jankovsky, Robert; Tverdokhlebov, Sergery; Manzella, David

1999-01-01

The development of Hall thrusters with powers ranging from tens of kilowatts to in excess of one hundred kilowatts is considered based on renewed interest in high power. high thrust electric propulsion applications. An approach to develop such thrusters based on previous experience is discussed. It is shown that the previous experimental data taken with thrusters of 10 kW input power and less can be used. Potential mass savings due to the design of high power Hall thrusters are discussed. Both xenon and alternate thruster propellant are considered, as are technological issues that will challenge the design of high power Hall thrusters. Finally, the implications of such a development effort with regard to ground testing and spacecraft intecrati'on issues are discussed.

Arcjet nozzle area ratio effects

NASA Technical Reports Server (NTRS)

Curran, Francis M.; Sarmiento, Charles J.; Birkner, Bjorn W.; Kwasny, James

1990-01-01

An experimental investigation was conducted to determine the effect of nozzle area ratio on the operating characteristics and performance of a low power dc arcjet thruster. Conical thoriated tungsten nozzle inserts were tested in a modular laboratory arcjet thruster run on hydrogen/nitrogen mixtures simulating the decomposition products of hydrazine. The converging and diverging sides of the inserts had half angles of 30 and 20 degrees, respectively, similar to a flight type unit currently under development. The length of the diverging side was varied to change the area ratio. The nozzle inserts were run over a wide range of specific power. Current, voltage, mass flow rate, and thrust were monitored to provide accurate comparisons between tests. While small differences in performance were observed between the two nozzle inserts, it was determined that for each nozzle insert, arcjet performance improved with increasing nozzle area ratio to the highest area ratio tested and that the losses become very pronounced for area ratios below 50. These trends are somewhat different than those obtained in previous experimental and analytical studies of low Re number nozzles. It appears that arcjet performance can be enhanced via area ratio optimization.

Arcjet Nozzle Area Ratio Effects

NASA Technical Reports Server (NTRS)

Curran, Francis M.; Sarmiento, Charles J.; Birkner, Bjorn W.; Kwasny, James

1990-01-01

An experimental investigation was conducted to determine the effect of nozzle area ratio on the operating characteristics and performance of a low power dc arcjet thruster. Conical thoriated tungsten nozzle inserts were tested in a modular laboratory arcjet thruster run on hydrogen/nitrogen mixtures simulating the decomposition products of hydrazine. The converging and diverging sides of the inserts had half angles of 30 and 20 degrees, respectively, similar to a flight type unit currently under development. The length of the diverging side was varied to change the area ratio. The nozzle inserts were run over a wide range of specific power. Current, voltage, mass flow rate, and thrust were monitored to provide accurate comparisons between tests. While small differences in performance were observed between the two nozzle inserts, it was determined that for each nozzle insert, arcjet performance improved with increasing nozzle area ratio to the highest area ratio tested and that the losses become very pronounced for area ratios below 50. These trends are somewhat different than those obtained in previous experimental and analytical studies of low Re number nozzles. It appears that arcjet performance can be enhanced via area ratio optimization.

Stand-alone containment analysis of Phébus FPT tests with ASTEC and MELCOR codes: the FPT-2 test.

PubMed

Gonfiotti, Bruno; Paci, Sandro

2018-03-01

During the last 40 years, many studies have been carried out to investigate the different phenomena occurring during a Severe Accident (SA) in a Nuclear Power Plant (NPP). Such efforts have been supported by the execution of different experimental campaigns, and the integral Phébus FP tests were probably some of the most important experiments in this field. In these tests, the degradation of a Pressurized Water Reactor (PWR) fuel bundle was investigated employing different control rod materials and burn-up levels in strongly or weakly oxidizing conditions. From the findings on these and previous tests, numerical codes such as ASTEC and MELCOR have been developed to analyze the evolution of a SA in real NPPs. After the termination of the Phébus FP campaign, these two codes have been furthermore improved to implement the more recent findings coming from different experimental campaigns. Therefore, continuous verification and validation is still necessary to check that the new improvements introduced in such codes allow also a better prediction of these Phébus tests. The aim of the present work is to re-analyze the Phébus FPT-2 test employing the updated ASTEC and MELCOR code versions. The analysis focuses on the stand-alone containment aspects of this test, and three different spatial nodalizations of the containment vessel (CV) have been developed. The paper summarizes the main thermal-hydraulic results and presents different sensitivity analyses carried out on the aerosols and fission products (FP) behavior. When possible, a comparison among the results obtained during this work and by different authors in previous work is also performed. This paper is part of a series of publications covering the four Phébus FP tests using a PWR fuel bundle: FPT-0, FPT-1, FPT-2, and FPT-3, excluding the FPT-4 one, related to the study of the release of low-volatility FP and transuranic elements from a debris bed and a pool of melted fuel.

Outer region scaling using the freestream velocity for nonuniform open channel flow over gravel

NASA Astrophysics Data System (ADS)

Stewart, Robert L.; Fox, James F.

2017-06-01

The theoretical basis for outer region scaling using the freestream velocity for nonuniform open channel flows over gravel is derived and tested for the first time. Owing to the gradual expansion of the flow within the nonuniform case presented, it is hypothesized that the flow can be defined as an equilibrium turbulent boundary layer using the asymptotic invariance principle. The hypothesis is supported using similarity analysis to derive a solution, followed by further testing with experimental datasets. For the latter, 38 newly collected experimental velocity profiles across three nonuniform flows over gravel in a hydraulic flume are tested as are 43 velocity profiles previously published in seven peer-reviewed journal papers that focused on fluid mechanics of nonuniform open channel over gravel. The findings support the nonuniform flows as equilibrium defined by the asymptotic invariance principle, which is reflective of the consistency of the turbulent structure's form and function within the expanding flow. However, roughness impacts the flow structure when comparing across the published experimental datasets. As a secondary objective, we show how previously published mixed scales can be used to assist with freestream velocity scaling of the velocity deficit and thus empirically account for the roughness effects that extend into the outer region of the flow. One broader finding of this study is providing the theoretical context to relax the use of the elusive friction velocity when scaling nonuniform flows in gravel bed rivers; and instead to apply the freestream velocity. A second broader finding highlighted by our results is that scaling of nonuniform flow in gravel bed rivers is still not fully resolved theoretically since mixed scaling relies to some degree on empiricism. As researchers resolve the form and function of macroturbulence in the outer region, we hope to see the closing of this research gap.

Thermomechanical deformation testing and modeling in the presence of metallurgical instabilities. M.S. Thesis - Akron Univ. Final Report

NASA Technical Reports Server (NTRS)

Castelli, Michael G.

1990-01-01

A number of viscoplastic constitutive models were developed to describe deformation behavior under complex combinations of thermal and mechanical loading. Questions remain, however, regarding the validity of procedures used to characterize these models for specific structural alloys. One area of concern is that the majority of experimental data available for this purpose are determined under isothermal conditions. This experimental study is aimed at determining whether viscoplastic constitutive theories characterized using an isothermal data base can adequately model material response under the complex thermomechanical loading conditions typical of power generation service. The approach adopted was to conduct a series of carefully controlled thermomechanical experiments on a nickel-based superalloy, Hastelloy Alloy X. Previous investigations had shown that this material experiences metallurgical instabilities leading to complex hardening behavior, termed dynamic strain aging. Investigating this phenomenon under full thermomechanical conditions leads to a number of challenging experimental difficulties which up to the present work were unresolved. To correct this situation, a number of advances were made in thermomechanical testing techniques. Advanced methods for dynamic temperature gradient control, phasing control and thermal strain compensation were developed and incorporated into real time test control software. These advances allowed the thermomechanical data to be analyzed with minimal experimental uncertainty. The thermomechanical results were evaluated on both a phenomenological and microstructural basis. Phenomenological results revealed that the thermomechanical hardening trends were not bounded by those displayed under isothermal conditions. For the case of Hastelloy Alloy X (and similar dynamic strain aging materials), this strongly suggests that some form of thermomechanical testing is necessary when characterizing a thermoviscoplastic deformation model. Transmission electron microscopy was used to study the microstructural physics, and analyze the unique phenomenological behavior.

Efficacy and effectiveness of alcohol in the disinfection of semi-critical materials: a systematic review

PubMed Central

Ribeiro, Maíra Marques; Neumann, Verena Ashley; Padoveze, Maria Clara; Graziano, Kazuko Uchikawa

2015-01-01

Abstract Objective: to assess the efficacy and the effectiveness of 60-80% alcohol (v/v) in the disinfection of semi-critical materials which were either previously cleaned or not. Method: studies obtained from BIREME, IBECS, MEDLINE, ScIELO, PubMed, Ask Medline web portals, and references from other studies. Criteria were created to assess the methodological quality of articles. Out of the 906 studies found, 14 have been included. Results: after materials were disinfected with alcohol, microorganisms were detected in 104/282 (36.9%) effectiveness tests and in 23/92 (25.0%) efficacy tests that were conducted. In the field studies, disinfection was not achieved for 74/218 (33.9%) of the products that were submitted to previous cleaning and for 30/64 (46.9%) of the ones which were not submitted to previous cleaning. In the experimental studies, alcohol disinfection was not efficacy in 11/30 (36.7%) and 12/62 (19.4%) of products, respectively. The studies were not found to have followed standardized methods. Conclusion: disinfection of semi-critical products with alcohol 70% - or in an approximate concentration - cannot be recommended to all health care products in an unrestricted way. However, according to the type of semi-critical product, disinfection can be attained with or without previous cleaning. PMID:26444178

Efficacy and effectiveness of alcohol in the disinfection of semi-critical materials: a systematic review.

PubMed

Ribeiro, Maíra Marques; Neumann, Verena Ashley; Padoveze, Maria Clara; Graziano, Kazuko Uchikawa

2015-01-01

to assess the efficacy and the effectiveness of 60-80% alcohol (v/v) in the disinfection of semi-critical materials which were either previously cleaned or not. studies obtained from BIREME, IBECS, MEDLINE, ScIELO, PubMed, Ask Medline web portals, and references from other studies. Criteria were created to assess the methodological quality of articles. Out of the 906 studies found, 14 have been included. after materials were disinfected with alcohol, microorganisms were detected in 104/282 (36.9%) effectiveness tests and in 23/92 (25.0%) efficacy tests that were conducted. In the field studies, disinfection was not achieved for 74/218 (33.9%) of the products that were submitted to previous cleaning and for 30/64 (46.9%) of the ones which were not submitted to previous cleaning. In the experimental studies, alcohol disinfection was not efficacy in 11/30 (36.7%) and 12/62 (19.4%) of products, respectively. The studies were not found to have followed standardized methods. disinfection of semi-critical products with alcohol 70% - or in an approximate concentration - cannot be recommended to all health care products in an unrestricted way. However, according to the type of semi-critical product, disinfection can be attained with or without previous cleaning.

Analysis of experimental results of the inlet for the NASA hypersonic research engine aerothermodynamic integration model. [wind tunnel tests of ramjet engine hypersonic inlets

NASA Technical Reports Server (NTRS)

Andrews, E. H., Jr.; Mackley, E. A.

1976-01-01

An aerodynamic engine inlet analysis was performed on the experimental results obtained at nominal Mach numbers of 5, 6, and 7 from the NASA Hypersonic Research Engine (HRE) Aerothermodynamic Integration Model (AIM). Incorporation on the AIM of the mixed-compression inlet design represented the final phase of an inlet development program of the HRE Project. The purpose of this analysis was to compare the AIM inlet experimental results with theoretical results. Experimental performance was based on measured surface pressures used in a one-dimensional force-momentum theorem. Results of the analysis indicate that surface static-pressure measurements agree reasonably well with theoretical predictions except in the regions where the theory predicts large pressure discontinuities. Experimental and theoretical results both based on the one-dimensional force-momentum theorem yielded inlet performance parameters as functions of Mach number that exhibited reasonable agreement. Previous predictions of inlet unstart that resulted from pressure disturbances created by fuel injection and combustion appeared to be pessimistic.

Experimental Verification of the Structural Glass Beam-Columns Strength

NASA Astrophysics Data System (ADS)

Pešek, Ondřej; Melcher, Jindřich; Balázs, Ivan

2017-10-01

This paper deals with experimental research of axially and laterally loaded members made of structural (laminated) glass. The purpose of the research is the evaluation of buckling strength and actual behaviour of the beam-columns due to absence of standards for design of glass load-bearing structures. The experimental research follows the previous one focusing on measuring of initial geometrical imperfections of glass members, testing of glass beams and columns. Within the frame of the research 9 specimens were tested. All of them were of the same geometry (length 2000 mm, width 200 mm and thickness 16 mm) but different composition - laminated double glass made of annealed glass or fully tempered glass panes bonded together by PVB or EVASAFE foil. Specimens were at first loaded by axial force and then by constantly increasing bending moment up to failure. During testing lateral deflections, vertical deflection and normal stresses at mid-span were measured. A maximum load achieved during testing has been adopted as flexural-lateral-torsional buckling strength. The results of experiments were statistically evaluated according to the European standard for design of structures EN 1990, appendix D. There are significant differences between specimens made of annealed glass or fully tempered glass. Differences between specimens loaded by axial forces 1 kN and 2 kN are negligible. The next step was to determine the design strength by calculation procedure based on buckling curves approach intended for design of steel columns and develop interaction criterion for glass beams-columns.

Are independent probes truly independent?

PubMed

Camp, Gino; Pecher, Diane; Schmidt, Henk G; Zeelenberg, René

2009-07-01

The independent cue technique has been developed to test traditional interference theories against inhibition theories of forgetting. In the present study, the authors tested the critical criterion for the independence of independent cues: Studied cues not presented during test (and unrelated to test cues) should not contribute to the retrieval process. Participants first studied a subset of cues (e.g., rope) that were subsequently studied together with a target in a 2nd study phase (e.g., rope-sailing, sunflower-yellow). In the test phase, an extralist category cue (e.g., sports, color) was presented, and participants were instructed to recall an item from the study list that was a member of the category (e.g., sailing, yellow). The experiments showed that previous study of the paired-associate word (e.g., rope) enhanced category cued recall even though this word was not presented at test. This experimental demonstration of covert cuing has important implications for the effectiveness of the independent cue technique.

Experimental investigation on the failure of T-joints at elevated temperature under unaxial loading

NASA Astrophysics Data System (ADS)

Bahri, N. F.; Afendi, M.; Razlan, Z. M.; Nor, A.; Baharuddin, S. A.

2017-09-01

In this study, the mechanical properties and maximum failure load of a bulk and T-joints subjected to tensile loading were investigated experimentally. A bulk and the T-joint specimens were fabricated and tested in order to investigate the effects of temperature conditions on the failure of the joints. The adherent and adhesive used for T-joint are 304 L stainless steel and Hysol E 214 HP with the adhesive thickness of 1.0 mm. The tensile test of the bulk specimen and adhesively T-joint were conducted by using a universal testing machine (UTM) at room temperature (RT), 55 °C, 75 °C, 100 °C and 120 °C, respectively. It was found that as the temperature increases, the failure force strength decreases for bulk and T-joint specimen. Data obtained from the tests at 120 °C showed the failure force of the bulk adhesive decreased by approximately 44 % compared to the specimen tested at RT. Next, the bulk of Hysol failure force result was compared with Araldite at RT and 100 °C. Araldite data was taken from the previous study [1]. It has also been found that the bulk for Hysol has higher failure force compared to Araldite at RT and 100 °C.

Experimental evaluation of oxygen-enriched air and emulsified fuels in a six-cylinder diesel engine

NASA Astrophysics Data System (ADS)

Sekar, R. R.; Marr, W. W.; Cole, R. L.; Marciniak, T. J.; Longman, D. E.

1993-01-01

The objectives of this investigation are to (1) determine the technical feasibility of using oxygen-enriched air to increase the efficiency of and reduce emissions from diesel engines, (2) examine the effects of water-emulsified fuel on the formation of nitrogen oxides in oxygen-enriched combustion, and (3) investigate the use of lower-grade fuels in high-speed diesel engines by emulsifying the fuel with water. These tests, completed on a Caterpillar model 3406B, six-cylinder engine are a scale-up from previous, single-cylinder-engine tests. The engine was tested with (1) intake-air oxygen levels up to 30%, (2) water content up to 20% of the fuel, (3) three fuel-injection timings, and (4) three fuel-flow rates (power levels). The Taguchi technique for experimental design was used to minimize the number of experimental points in the test matrix. Four separate test matrices were run to cover two different fuel-flow-rate strategies and two different fuels (No. 2 diesel and No. 6 diesel). A liquid-oxygen tank located outside the test cell supplied the oxygen for the tests. The only modification of the engine was installation of a pressure transducer in one cylinder. All tests were run at 1800 rpm, which corresponds to the synchronous speed of a 60-Hz generator. Test results show that oxygen enrichment results in power increases of 50% or more while significantly decreasing the levels of smoke and particulates emitted. The increase in power was accompanied by a small increase in thermal efficiency. Maximum engine power was limited by the test-cell dynamometer capacity and the capacity of the fuel-injection pump. Oxygen enrichment increases nitrogen-oxide emissions significantly. No adverse effects of oxygen enrichment on the turbocharger were observed. The engine operated successfully with No. 6 fuel, but it operated at a lower thermal efficiency and emitted more smoke and particulates than with No. 2 fuel.

Bacterial bioluminescence onset and quenching: a dynamical model for a quorum sensing-mediated property

PubMed Central

Side, Domenico Delle; Nassisi, Vincenzo; Pennetta, Cecilia; Alifano, Pietro; Di Salvo, Marco; Talà, Adelfia; Chechkin, Aleksei; Seno, Flavio

2017-01-01

We present an effective dynamical model for the onset of bacterial bioluminescence, one of the most studied quorum sensing-mediated traits. Our model is built upon simple equations that describe the growth of the bacterial colony, the production and accumulation of autoinducer signal molecules, their sensing within bacterial cells, and the ensuing quorum activation mechanism that triggers bioluminescent emission. The model is directly tested to quantitatively reproduce the experimental distributions of photon emission times, previously measured for bacterial colonies of Vibrio jasicida, a luminescent bacterium belonging to the Harveyi clade, growing in a highly drying environment. A distinctive and novel feature of the proposed model is bioluminescence ‘quenching’ after a given time elapsed from activation. Using an advanced fitting procedure based on the simulated annealing algorithm, we are able to infer from the experimental observations the biochemical parameters used in the model. Such parameters are in good agreement with the literature data. As a further result, we find that, at least in our experimental conditions, light emission in bioluminescent bacteria appears to originate from a subtle balance between colony growth and quorum activation due to autoinducers diffusion, with the two phenomena occurring on the same time scale. This finding is consistent with a negative feedback mechanism previously reported for Vibrio harveyi. PMID:29308273

Bacterial bioluminescence onset and quenching: a dynamical model for a quorum sensing-mediated property.

PubMed

Side, Domenico Delle; Nassisi, Vincenzo; Pennetta, Cecilia; Alifano, Pietro; Di Salvo, Marco; Talà, Adelfia; Chechkin, Aleksei; Seno, Flavio; Trovato, Antonio

2017-12-01

We present an effective dynamical model for the onset of bacterial bioluminescence, one of the most studied quorum sensing-mediated traits. Our model is built upon simple equations that describe the growth of the bacterial colony, the production and accumulation of autoinducer signal molecules, their sensing within bacterial cells, and the ensuing quorum activation mechanism that triggers bioluminescent emission. The model is directly tested to quantitatively reproduce the experimental distributions of photon emission times, previously measured for bacterial colonies of Vibrio jasicida , a luminescent bacterium belonging to the Harveyi clade, growing in a highly drying environment. A distinctive and novel feature of the proposed model is bioluminescence 'quenching' after a given time elapsed from activation. Using an advanced fitting procedure based on the simulated annealing algorithm, we are able to infer from the experimental observations the biochemical parameters used in the model. Such parameters are in good agreement with the literature data. As a further result, we find that, at least in our experimental conditions, light emission in bioluminescent bacteria appears to originate from a subtle balance between colony growth and quorum activation due to autoinducers diffusion, with the two phenomena occurring on the same time scale. This finding is consistent with a negative feedback mechanism previously reported for Vibrio harveyi .

Preliminary Interpretation of a Radionuclide and Colloid Tracer Test in a Granodiorite Shear Zone at the Grimsel Test Site, Switzerland

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reimus, Paul W.

2012-08-30

In February and March 2012, a tracer test involving the injection of a radionuclide-colloid cocktail was conducted in the MI shear zone at the Grimsel Test Site, Switzerland, as part of the Colloids Formation and Migration (CFM) project. The colloids were derived from FEBEX bentonite, which is mined in Spain and is being considered as a potential waste package backfill in a Spanish nuclear waste repository. The tracer test, designated test 12-02 (second test in 2012), involved the injection of the tracer cocktail into borehole CFM 06.002i2 and extraction from the Pinkel surface packer at the main access tunnel wallmore » approximately 6.1 m from the injection interval. The test configuration is depicted in Figure 1. This configuration has been used in several conservative tracer tests and two colloid-homologue tracer tests since 2007, and it is will be employed in an upcoming test involving the emplacement of a radionuclide-doped bentonite plug into CFM 06.002i2 to evaluate the swelling and erosion of the bentonite and the transport of bentonite colloids and radionuclides from the source to the extraction point at the tunnel wall. Interpretive analyses of several of the previous tracer tests, from 09-01 through 12-02 were provided in two previous Used Fuel Disposition Program milestone reports (Arnold et al., 2011; Kersting et al., 2012). However, only the data for the conservative tracer Amino-G Acid was previously analyzed from test 12-02 because the other tracer data from this test were not available at the time. This report documents the first attempt to quantitatively analyze the radionuclide and colloid breakthrough curves from CFM test 12-02. This report was originally intended to also include an experimental assessment of colloid-facilitated transport of uranium by bentonite colloids in the Grimsel system, but this assessment was not conducted because it was reported by German collaborators at the Karlsruhe Institute of Technology (KIT) that neither uranium nor neptunium adsorbed appreciably to FEBEX bentonite colloids in Grimsel groundwater (Huber et al., 2011). The Grimsel groundwater has a relatively high pH of {approx}9, so the lack of uranium and neptunium adsorption to clay is not surprising given the tendency for these actinides to form very stable negative or neutrally-charged uranyl- or calcium-uranyl-carbonate complexes at these pH, particularly in a water that is effectively saturated with respect to calcite. It was also observed in testing conducted at LANL earlier in 2012 that uranium did not adsorb measurably to Grimsel granodiorite in a synthetic Grimsel groundwater at pH {approx}8.5 (Kersting et al., 2012). Thus, the planned experimental work was not pursued because all the available information clearly pointed to an expected result that uranium transport would not be facilitated by clay colloids in the Grimsel system.« less

Aniracetam does not alter cognitive and affective behavior in adult C57BL/6J mice.

PubMed

Elston, Thomas W; Pandian, Ashvini; Smith, Gregory D; Holley, Andrew J; Gao, Nanjing; Lugo, Joaquin N

2014-01-01

There is a growing community of individuals who self-administer the nootropic aniracetam for its purported cognitive enhancing effects. Aniracetam is believed to be therapeutically useful for enhancing cognition, alleviating anxiety, and treating various neurodegenerative conditions. Physiologically, aniracetam enhances both glutamatergic neurotransmission and long-term potentiation. Previous studies of aniracetam have demonstrated the cognition-restoring effects of acute administration in different models of disease. No previous studies have explored the effects of aniracetam in healthy subjects. We investigated whether daily 50 mg/kg oral administration improves cognitive performance in naïve C57BL/6J mice in a variety of aspects of cognitive behavior. We measured spatial learning in the Morris water maze test; associative learning in the fear conditioning test; motor learning in the accelerating rotarod test; and odor discrimination. We also measured locomotion in the open field test, anxiety through the elevated plus maze test and by measuring time in the center of the open field test. We measured repetitive behavior through the marble burying test. We detected no significant differences between the naive, placebo, and experimental groups across all measures. Despite several studies demonstrating efficacy in impaired subjects, our findings suggest that aniracetam does not alter behavior in normal healthy mice. This study is timely in light of the growing community of healthy humans self-administering nootropic drugs.

Aniracetam Does Not Alter Cognitive and Affective Behavior in Adult C57BL/6J Mice

PubMed Central

Elston, Thomas W.; Pandian, Ashvini; Smith, Gregory D.; Holley, Andrew J.; Gao, Nanjing; Lugo, Joaquin N.

2014-01-01

There is a growing community of individuals who self-administer the nootropic aniracetam for its purported cognitive enhancing effects. Aniracetam is believed to be therapeutically useful for enhancing cognition, alleviating anxiety, and treating various neurodegenerative conditions. Physiologically, aniracetam enhances both glutamatergic neurotransmission and long-term potentiation. Previous studies of aniracetam have demonstrated the cognition-restoring effects of acute administration in different models of disease. No previous studies have explored the effects of aniracetam in healthy subjects. We investigated whether daily 50 mg/kg oral administration improves cognitive performance in naïve C57BL/6J mice in a variety of aspects of cognitive behavior. We measured spatial learning in the Morris water maze test; associative learning in the fear conditioning test; motor learning in the accelerating rotarod test; and odor discrimination. We also measured locomotion in the open field test, anxiety through the elevated plus maze test and by measuring time in the center of the open field test. We measured repetitive behavior through the marble burying test. We detected no significant differences between the naive, placebo, and experimental groups across all measures. Despite several studies demonstrating efficacy in impaired subjects, our findings suggest that aniracetam does not alter behavior in normal healthy mice. This study is timely in light of the growing community of healthy humans self-administering nootropic drugs. PMID:25099639

Predicting the occurrence of mixed mode failure associated with hydraulic fracturing, part 2 water saturated tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauer, Stephen J.; Broome, Scott Thomas; Choens, Charles

2015-09-14

Seven water-saturated triaxial extension experiments were conducted on four sedimentary rocks. This experimental condition was hypothesized more representative of that existing for downhole hydrofracture and thus it may improve our understanding of the phenomena. In all tests the pore pressure was 10 MPa and confirming pressure was adjusted to achieve tensile and transitional failure mode conditions. Using previous work in this LDRD for comparison, the law of effective stress is demonstrated in extension using this sample geometry. In three of the four lithologies, no apparent chemo-mechanical effect of water is apparent, and in the fourth lithology test results indicate somemore » chemo-mechanical effect of water.« less

Task-level testing of the JPL-OMV smart end effector

NASA Technical Reports Server (NTRS)

Hannaford, B.

1987-01-01

An intelligent end effector previously developed at JPL has been tested in over 21 hours of experimental teleoperation. The end effector provides local control of gripper clamping force and a 6-degree-of-freedom, wrist mounted force torque sensor. Resolved forces and torques were displayed to the test subjects, and the effect of this information on their performance of simulated satellite servicing tasks was assessed. The experienced subjects accomplished the tasks with lower levels of Remote Manipulator System (RMS) forces than intermediate and naive subjects, but the force levels were apparently uncorrelated with the presence or absence of the display. This negative finding was attributed to the lack of a suitable control mode in the manipulator control system.

Determination of the thermal stability of fluids by tensimetry - Instrumentation and procedure

NASA Technical Reports Server (NTRS)

Helmick, Larry S.; Jones, William R., Jr.

1990-01-01

A computerized tensimeter and experimental procedure for determination of the thermal decomposition temperature (T sub d) of perfluoro alkylethers were developed and tested. Both the apparatus and the procedure are described in detail. Results of testing with bis(2-ethylhexyl) phthalate and trimethylolpropane triheptanoate demonstrate that the reciprocal of the decomposition temperature is a linear function of the logarithm of the gas volume/heated liquid volume ratio. The T sub d obtained for each compound at a gas volume/heated liquid volume ration of one was similar to the value previously reported using an isoteniscope technique. Results of testing with a polymer of hexafluoropropylene oxide demonstrate that this instrument and procedure can be used to determine the T sub d of perfluoro alkylethers.

Determination of the thermal stability of perfluoroalkylethers by tensimetry: Instrumentation and Procedure

NASA Technical Reports Server (NTRS)

Helmick, Larry S.; Jones, William R., Jr.

1989-01-01

A computerized tensimeter and experimental procedure for determination of the thermal decomposition temperature (T sub d) of perfluoro alkylethers were developed and tested. Both the apparatus and the procedure are described in detail. Results of testing with bis(2-ethylhexyl) phthalate and trimethylolpropane triheptanoate demonstrate that the reciprocal of the decomposition temperature is a linear function of the logarithm of the gas volume/heated liquid volume ratio. The T sub d obtained for each compound at a gas volume/heated liquid volume ration of one was similar to the value previously reported using an isoteniscope technique. Results of testing with a polymer of hexafluoropropylene oxide demonstrate that this instrument and procedure can be used to determine the T sub d of perfluoroalkylethers.

Alternative Computational Protocols for Supercharging Protein Surfaces for Reversible Unfolding and Retention of Stability

PubMed Central

Der, Bryan S.; Kluwe, Christien; Miklos, Aleksandr E.; Jacak, Ron; Lyskov, Sergey; Gray, Jeffrey J.; Georgiou, George; Ellington, Andrew D.; Kuhlman, Brian

2013-01-01

Reengineering protein surfaces to exhibit high net charge, referred to as “supercharging”, can improve reversibility of unfolding by preventing aggregation of partially unfolded states. Incorporation of charged side chains should be optimized while considering structural and energetic consequences, as numerous mutations and accumulation of like-charges can also destabilize the native state. A previously demonstrated approach deterministically mutates flexible polar residues (amino acids DERKNQ) with the fewest average neighboring atoms per side chain atom (AvNAPSA). Our approach uses Rosetta-based energy calculations to choose the surface mutations. Both protocols are available for use through the ROSIE web server. The automated Rosetta and AvNAPSA approaches for supercharging choose dissimilar mutations, raising an interesting division in surface charging strategy. Rosetta-supercharged variants of GFP (RscG) ranging from −11 to −61 and +7 to +58 were experimentally tested, and for comparison, we re-tested the previously developed AvNAPSA-supercharged variants of GFP (AscG) with +36 and −30 net charge. Mid-charge variants demonstrated ∼3-fold improvement in refolding with retention of stability. However, as we pushed to higher net charges, expression and soluble yield decreased, indicating that net charge or mutational load may be limiting factors. Interestingly, the two different approaches resulted in GFP variants with similar refolding properties. Our results show that there are multiple sets of residues that can be mutated to successfully supercharge a protein, and combining alternative supercharge protocols with experimental testing can be an effective approach for charge-based improvement to refolding. PMID:23741319

Animal models of protein allergenicity: potential benefits, pitfalls and challenges.

PubMed

Dearman, R J; Kimber, I

2009-04-01

Food allergy is an important health issue. With an increasing interest in novel foods derived from transgenic crop plants, there is a growing need for the development of approaches suitable for the characterization of the allergenic potential of proteins. There are methods available currently (such as homology searches and serological testing) that are very effective at identifying proteins that are likely to cross-react with known allergens. However, animal models may play a role in the identification of truly novel proteins, such as bacterial or fungal proteins, that have not been experienced previously in the diet. We consider here the potential benefits, pitfalls and challenges of the selection of various animal models, including the mouse, the rat, the dog and the neonatal swine. The advantages and disadvantages of various experimental end-points are discussed, including the measurement of specific IgE by ELISA, Western blotting or functional tests such as the passive cutaneous anaphylaxis assay, and the assessment of challenge-induced clinical symptoms in previously sensitized animals. The experimental variables of route of exposure to test proteins and the incorporation of adjuvant to increase the sensitivity of the responses are considered also. It is important to emphasize that currently none of these approaches has been validated for the purposes of hazard identification in the context of a safety assessment. However, the available evidence suggests that the judicious use of an accurate and robust animal model could provide important additional data that would contribute significantly to the assessment of the potential allergenicity of novel proteins.

Heat Transfer Experiments in the Internal Cooling Passages of a Cooled Radial Turbine Rotor

NASA Technical Reports Server (NTRS)

Johnson, B. V.; Wagner, J. H.

1996-01-01

An experimental study was conducted (1) to experimentally measure, assess and analyze the heat transfer within the internal cooling configuration of a radial turbine rotor blade and (2) to obtain heat transfer data to evaluate and improve computational fluid dynamics (CFD) procedures and turbulent transport models of internal coolant flows. A 1.15 times scale model of the coolant passages within the NASA LERC High Temperature Radial Turbine was designed, fabricated of Lucite and instrumented for transient beat transfer tests using thin film surface thermocouples and liquid crystals to indicate temperatures. Transient heat transfer tests were conducted for Reynolds numbers of one-fourth, one-half, and equal to the operating Reynolds number for the NASA Turbine. Tests were conducted for stationary and rotating conditions with rotation numbers in the range occurring in the NASA Turbine. Results from the experiments showed the heat transfer characteristics within the coolant passage were affected by rotation. In general, the heat transfer increased and decreased on the sides of the straight radial passages with rotation as previously reported from NASA-HOST-sponsored experiments. The heat transfer in the tri-passage axial flow region adjacent to the blade exit was relatively unaffected by rotation. However, the heat transfer on one surface, in the transitional region between the radial inflow passage and axial, constant radius passages, decreased to approximately 20 percent of the values without rotation. Comparisons with previous 3-D numerical studies indicated regions where the heat transfer characteristics agreed and disagreed with the present experiment.

Detection and analysis of part load and full load instabilities in a real Francis turbine prototype

NASA Astrophysics Data System (ADS)

Presas, Alexandre; Valentin, David; Egusquiza, Eduard; Valero, Carme

2017-04-01

Francis turbines operate in many cases out of its best efficiency point, in order to regulate their output power according to the instantaneous energy demand of the grid. Therefore, it is of paramount importance to analyse and determine the unstable operating points for these kind of units. In the framework of the HYPERBOLE project (FP7-ENERGY-2013-1; Project number 608532) a large Francis unit was investigated numerically, experimentally in a reduced scale model and also experimentally and numerically in the real prototype. This paper shows the unstable operating points identified during the experimental tests on the real Francis unit and the analysis of the main characteristics of these instabilities. Finally, it is shown that similar phenomena have been identified on previous research in the LMH (Laboratory for Hydraulic Machines, Lausanne) with the reduced scale model.

Experimental and natural host specificity of Loma salmonae (Microsporidia).

PubMed

Shaw, R W; Kent, M L; Brown, A M; Whipps, C M; Adamson, M L

2000-03-14

The microsporidian Loma salmonae (Putz, Hoffman & Dunbar, 1965) Morrison & Sprague, 1981 has caused significant gill disease in Pacific salmon Oncorhynchus spp. Host specificity of the parasite was examined experimentally by per os challenge of selected salmonids and non-salmonids with infective chinook salmon O. tshawytscha gill material. Pink Oncorhynchus gorbuscha and chum salmon O. keta, brown Salmo trutta and brook trout Salvelinus fontinalis, and chinook salmon (controls) were positive, whereas Atlantic salmon Salmo salar and Arctic char Salvelinus alpinus were negative. In addition, no non-salmonids were susceptible to experimental exposure. Wild Pacific salmon species in British Columbia, Canada, were examined for L. salmonae during their freshwater life history stages (smolts, prespawning, spawning). All stages were infected, although infections in smolts were only detectable using a L. salmonae-specific PCR test. Many previous Loma spp. described from Oncorhychus spp. are likely L. salmonae based on host, parasite morphology, and site of infection.

Experimental validation of 2D uncertainty quantification for DIC.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reu, Phillip L.

Because digital image correlation (DIC) has become such an important and standard tool in the toolbox of experimental mechanicists, a complete uncertainty quantification of the method is needed. It should be remembered that each DIC setup and series of images will have a unique uncertainty based on the calibration quality and the image and speckle quality of the analyzed images. Any pretest work done with a calibrated DIC stereo-rig to quantify the errors using known shapes and translations, while useful, do not necessarily reveal the uncertainty of a later test. This is particularly true with high-speed applications where actual testmore » images are often less than ideal. Work has previously been completed on the mathematical underpinnings of DIC uncertainty quantification and is already published, this paper will present corresponding experimental work used to check the validity of the uncertainty equations.« less

Experimental validation of 2D uncertainty quantification for digital image correlation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reu, Phillip L.

Because digital image correlation (DIC) has become such an important and standard tool in the toolbox of experimental mechanicists, a complete uncertainty quantification of the method is needed. It should be remembered that each DIC setup and series of images will have a unique uncertainty based on the calibration quality and the image and speckle quality of the analyzed images. Any pretest work done with a calibrated DIC stereo-rig to quantify the errors using known shapes and translations, while useful, do not necessarily reveal the uncertainty of a later test. This is particularly true with high-speed applications where actual testmore » images are often less than ideal. Work has previously been completed on the mathematical underpinnings of DIC uncertainty quantification and is already published, this paper will present corresponding experimental work used to check the validity of the uncertainty equations.« less

Optimization and experimental realization of the quantum permutation algorithm

NASA Astrophysics Data System (ADS)

Yalçınkaya, I.; Gedik, Z.

2017-12-01

The quantum permutation algorithm provides computational speed-up over classical algorithms for determining the parity of a given cyclic permutation. For its n -qubit implementations, the number of required quantum gates scales quadratically with n due to the quantum Fourier transforms included. We show here for the n -qubit case that the algorithm can be simplified so that it requires only O (n ) quantum gates, which theoretically reduces the complexity of the implementation. To test our results experimentally, we utilize IBM's 5-qubit quantum processor to realize the algorithm by using the original and simplified recipes for the 2-qubit case. It turns out that the latter results in a significantly higher success probability which allows us to verify the algorithm more precisely than the previous experimental realizations. We also verify the algorithm for the first time for the 3-qubit case with a considerable success probability by taking the advantage of our simplified scheme.

Do you remember proposing marriage to the Pepsi machine? False recollections from a campus walk.

PubMed

Seamon, John G; Philbin, Morgan M; Harrison, Liza G

2006-10-01

During a campus walk, participants were given familiar or bizarre action statements (e.g., "Check the Pepsi machine for change" vs. "Propose marriage to the Pepsi machine") with instructions either to perform the actions or imagine performing the actions (Group 1) or to watch the experimenter perform the actions or imagine the experimenter performing the actions (Group 2). One day later, some actions were repeated, along with new actions, on a second walk. Two weeks later, the participants took a recognition test for actions presented during the first walk, and they specified whether a recognized action was imagined or performed. Imagining themselves or the experimenter performing familiar or bizarre actions just once led to false recollections of performance for both types of actions. This study extends previous research on imagination inflation by demonstrating that these false performance recollections can occur in a natural, real-life setting following just one imagining.

Experimental parametric study of servers cooling management in data centers buildings

NASA Astrophysics Data System (ADS)

Nada, S. A.; Elfeky, K. E.; Attia, Ali M. A.; Alshaer, W. G.

2017-06-01

A parametric study of air flow and cooling management of data centers servers is experimentally conducted for different design conditions. A physical scale model of data center accommodating one rack of four servers was designed and constructed for testing purposes. Front and rear rack and server's temperatures distributions and supply/return heat indices (SHI/RHI) are used to evaluate data center thermal performance. Experiments were conducted to parametrically study the effects of perforated tiles opening ratio, servers power load variation and rack power density. The results showed that (1) perforated tile of 25% opening ratio provides the best results among the other opening ratios, (2) optimum benefit of cold air in servers cooling is obtained at uniformly power loading of servers (3) increasing power density decrease air re-circulation but increase air bypass and servers temperature. The present results are compared with previous experimental and CFD results and fair agreement was found.

Experimental study on beam for composite CES structural system

NASA Astrophysics Data System (ADS)

Matsui, Tomoya

2017-10-01

Development study on Concrete Encase Steel (CES) composite structure system has been continuously conducted toward the practical use. CES structure is composed of steel and fiber reinforced concrete. In previous study, it was found that CES structure has good seismic performance from experimental study of columns, beam - column joints, shear walls and a two story two span frame. However, as fundamental study on CES beam could be lacking, it is necessary to understand the structural performance of CES beam. In this study, static loading tests of CES beams were conducted with experimental valuable of steel size, the presence or absence of slab and thickness of slab. And restoring characteristics, failure behavior, deformation behavior, and strength evaluation method of CES beam were investigated. As the results, it was found that CES beam showed stable hysteresis behavior. Furthermore it was found that the flexural strength of the CES beam could be evaluated by superposition strength theory.

Electron-nuclear spin dynamics of Ga centers in GaAsN dilute nitride semiconductors probed by pump-probe spectroscopy

NASA Astrophysics Data System (ADS)

Sandoval-Santana, J. C.; Ibarra-Sierra, V. G.; Azaizia, S.; Carrère, H.; Bakaleinikov, L. A.; Kalevich, V. K.; Ivchenko, E. L.; Marie, X.; Amand, T.; Balocchi, A.; Kunold, A.

2018-03-01

We propose an experimental procedure to track the evolution of electronic and nuclear spins in Ga2+ centers in GaAsN dilute semiconductors. The method is based on a pump-probe scheme that enables to monitor the time evolution of the three components of the electronic and nuclear spin variables. In contrast to other characterization methods, as nuclear magnetic resonance, this one only needs moderate magnetic fields (B≈ 10 mT), and does not require microwave irradiation. Specifically, we carry out a series of tests for different experimental conditions in order to optimize the procedure for maximum sensitivity in the measurement of the circular degree of polarization. Based on previous experimental results and the theoretical calculations presented here, we estimate that the method could yield a time resolution of about 10ps.

Self-consistent radiation-based simulation of electric arcs: II. Application to gas circuit breakers

NASA Astrophysics Data System (ADS)

Iordanidis, A. A.; Franck, C. M.

2008-07-01

An accurate and robust method for radiative heat transfer simulation for arc applications was presented in the previous paper (part I). In this paper a self-consistent mathematical model based on computational fluid dynamics and a rigorous radiative heat transfer model is described. The model is applied to simulate switching arcs in high voltage gas circuit breakers. The accuracy of the model is proven by comparison with experimental data for all arc modes. The ablation-controlled arc model is used to simulate high current PTFE arcs burning in cylindrical tubes. Model accuracy for the lower current arcs is evaluated using experimental data on the axially blown SF6 arc in steady state and arc resistance measurements close to current zero. The complete switching process with the arc going through all three phases is also simulated and compared with the experimental data from an industrial circuit breaker switching test.

Cryogenically formed prestressed composite fiber-metal structures for O2/N2 high pressure gas tanks.

NASA Technical Reports Server (NTRS)

Gleich, D.

1971-01-01

Demonstration of high-structural-performance ARDEFORM cryoformed 301 stainless-steel glass-fiber-reinforced (GFR) vessels by room temperature tests of 13 1/2-in. diam spheres. Tests verified that the structural performance of ARDEFORM spherical GFR vessels not only exceeded that of all metal construction, but also bettered previous GFR experimental results by 50%. Achievement of essentially the full strength of fiberglass in a spherical wrap pattern was again verified. Significant weight advantages for this construction are projected for O2/N2 high-pressure gas tanks for Space Shuttle environmental control/life support system missions.

Flutter suppression digital control law design and testing for the AFW wind tunnel model

NASA Technical Reports Server (NTRS)

Mukhopadhyay, Vivek

1994-01-01

The design of a control law for simultaneously suppressing the symmetric and antisymmetric flutter modes of a sting mounted fixed-in-roll aeroelastic wind-tunnel model is described. The flutter suppression control law was designed using linear quadratic Gaussian theory, and it also involved control law order reduction, a gain root-locus study, and use of previous experimental results. A 23 percent increase in the open-loop flutter dynamic pressure was demonstrated during the wind-tunnel test. Rapid roll maneuvers at 11 percent above the symmetric flutter boundary were also performed when the model was in a free-to-roll configuration.

Influence of free-stream disturbances on boundary-layer transition

NASA Technical Reports Server (NTRS)

Harvey, W. D.

1978-01-01

Considerable experimental evidence exists which shows that free stream disturbances (the ratio of root-mean-square pressure fluctuations to mean values) in conventional wind tunnels increase with increasing Mach number at low supersonic to moderate hypersonic speeds. In addition to local conditions, the free stream disturbance level influences transition behavior on simple test models. Based on this observation, existing noise transition data obtained in the same test facility were correlated for a large number of reference sharp cones and flat plates and are shown to collapse along a single curve. This result is a significant improvement over previous attempts to correlate noise transition data.

Consistent differences in individual reactions to drugs and dummies

PubMed Central

Joyce, C. R. B.

1959-01-01

The tendency of some individuals to report changes of physical and mental state after taking pharmacologically inert substances has been investigated experimentally. In a class of healthy medical students, those individuals who reported symptoms and those who did not made significantly different scores on a number of behavioural tests. The likely reactions of the members of a second class (containing none of the previous participants) to dummies were then predicted from their scores on the same tests, some of which were found to be much more efficient predictors than would have been expected by chance. Some implications for further research and for clinical medicine are discussed. PMID:14408028

Shear properties of pultruded fiber reinforced polymer composite materials

NASA Astrophysics Data System (ADS)

Seo, J. H.; Kim, S. H.; Ok, D. M.; An, D. J.; Yoon, S. J.

2018-06-01

This paper focuses on the mechanical properties of PFRP composite materials. Especially, relationship between shear property and the other mechanical properties of PFRP composite materials is investigated through comparison between experimental and theoretical results. The shear property of PFRP composite specimen is calculated from the theoretical equations which were suggested in previous studies. In addition, comparison between the shear property determined by the tensile test and the shear property calculated from theoretical equations is conducted and discussed. It was found that the theoretically predicted shear modulus of elasticity considering contiguity is close to the shear modulus of elasticity obtained by the 45° off-axis tensile test.

Flutter suppression digital control law design and testing for the AFW wind tunnel model

NASA Technical Reports Server (NTRS)

Mukhopadhyay, Vivek

1992-01-01

Design of a control law for simultaneously suppressing the symmetric and antisymmetric flutter modes of a sting mounted fixed-in-roll aeroelastic wind tunnel model is described. The flutter suppression control law was designed using linear quadratic Gaussian theory, and involved control law order reduction, a gain root-locus study and use of previous experimental results. A 23 percent increase in the open-loop flutter dynamic pressure was demonstrated during the wind tunnel test. Rapid roll maneuvers at 11 percent above the symmetric flutter boundary were also performed when the model was in a free-to-roll configuration.

Flutter suppression digital control law design and testing for the AFW wind-tunnel model

NASA Technical Reports Server (NTRS)

Mukhopadhyay, Vivek

1992-01-01

Design of a control law for simultaneously suppressing the symmetric and antisymmetric flutter modes of a string mounted fixed-in-roll aeroelastic wind tunnel model is described. The flutter suppression control law was designed using linear quadratic Gaussian theory and involved control law order reduction, a gain root-locus study, and the use of previous experimental results. A 23 percent increase in open-loop flutter dynamic pressure was demonstrated during the wind tunnel test. Rapid roll maneuvers at 11 percent above the symmetric flutter boundary were also performed when the model was in a free-to-roll configuration.

Effects of Compressibility on the Characteristics of Five Airfoils

DTIC Science & Technology

1947-04-25

noed.for ojnorliientEO data therefore ia greet« References l, S, and 3 rao representative of previous experimental data« Force measurements, «fato...of this investigation v«s to provide data to illustrate the effecte of compressibility en tho characteristics of airfoils of tho newer low-drag...were oliraäne.tod. TESIS ji Airfoil sections were tested which are representative of those either in uso or considered for use. In tills group are

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saboia, A.; Toscano, F.; Walborn, S. P.

We derive a family of entanglement criteria for continuous-variable systems based on the Renyi entropy of complementary distributions. We show that these entanglement witnesses can be more sensitive than those based on second-order moments, as well as previous tests involving the Shannon entropy [Phys. Rev. Lett. 103, 160505 (2009)]. We extend our results to include the case of discrete sampling. We provide several numerical results which show that our criteria can be used to identify entanglement in a number of experimentally relevant quantum states.

Numerical and experimental determination of weld pool shape during high-power diode laser welding

NASA Astrophysics Data System (ADS)

Klimpel, Andrzej; Lisiecki, Aleksander; Szymanski, Andrzej; Hoult, Anthony P.

2003-10-01

In this paper, results of investigations on the shape of weld pool during High Power Diode Laser (HPDL) welding are presented. The results of tests showed that the shape of weld pool and mechanism of laser welding with a rectangular pattern of 808 nm laser radiation differs distinctly from previous laser welding mechanisms. For all power densities the conduction mode welds were observed and weld pool geometry depends significantly on the welding parameters.

Using Temporal Modulation Sensitivity to Select Stimulation Sites for Processor MAPs in Cochlear Implant Listeners

PubMed Central

Garadat, Soha N.; Zwolan, Teresa A.; Pfingst, Bryan E.

2013-01-01

Previous studies in our laboratory showed that temporal acuity as assessed by modulation detection thresholds (MDTs) varied across activation sites and that this site-to-site variability was subject specific. Using two 10-channel MAPs, the previous experiments showed that processor MAPs that had better across-site mean (ASM) MDTs yielded better speech recognition than MAPs with poorer ASM MDTs tested in the same subject. The current study extends our earlier work on developing more optimal fitting strategies to test the feasibility of using a site-selection approach in the clinical domain. This study examined the hypothesis that revising the clinical speech processor MAP for cochlear implant (CI) recipients by turning off selected sites that have poorer temporal acuity and reallocating frequencies to the remaining electrodes would lead to improved speech recognition. Twelve CI recipients participated in the experiments. We found that site selection procedure based on MDTs in the presence of a masker resulted in improved performance on consonant recognition and recognition of sentences in noise. In contrast, vowel recognition was poorer with the experimental MAP than with the clinical MAP, possibly due to reduced spectral resolution when sites were removed from the experimental MAP. Overall, these results suggest a promising path for improving recipient outcomes using personalized processor-fitting strategies based on a psychophysical measure of temporal acuity. PMID:23881208

The use of concrete learning objects taken from the history of mathematics in mathematics education

NASA Astrophysics Data System (ADS)

Bütüner, Suphi Önder

2016-11-01

This study aimed to reveal the effects of teaching with concrete learning objects taken from the history of mathematics on student achievement. Being a quasi-experimental study, it was conducted with two grade 8 classes in a secondary school located in Trabzon. The experimental group consisted of 27 students and the control group consisted of 25. Data were collected by using worksheets, an achievement exam and written opinion forms. The data from the achievement exam were analysed by using the Mann-Whitney U-test while the data from written opinion forms were analysed through content analysis. The Mann-Whitney U-test results showed a significant difference between the mean ranks of the experimental and control groups in favour of the former. Findings from the written opinion forms suggested that the students found the activities to be instructive and fun, enjoyed using concrete models in their classes, and learned from discovering the rules. It was also found that students had previously not engaged in similar activities and had only experienced the history of mathematics through the life stories and works of mathematicians and the representation of ancient numbers at the beginning of each unit.

Experimental test of scaling of mixing by chaotic advection in droplets moving through microfluidic channels

PubMed Central

Song, Helen; Bringer, Michelle R.; Tice, Joshua D.; Gerdts, Cory J.; Ismagilov, Rustem F.

2006-01-01

This letter describes an experimental test of a simple argument that predicts the scaling of chaotic mixing in a droplet moving through a winding microfluidic channel. Previously, scaling arguments for chaotic mixing have been described for a flow that reduces striation length by stretching, folding, and reorienting the fluid in a manner similar to that of the baker’s transformation. The experimentally observed flow patterns within droplets (or plugs) resembled the baker’s transformation. Therefore, the ideas described in the literature could be applied to mixing in droplets to obtain the scaling argument for the dependence of the mixing time, t~(aw/U)log(Pe), where w [m] is the cross-sectional dimension of the microchannel, a is the dimensionless length of the plug measured relative to w, U [m s−1] is the flow velocity, Pe is the Péclet number (Pe=wU/D), and D [m2s−1] is the diffusion coefficient of the reagent being mixed. Experiments were performed to confirm the scaling argument by varying the parameters w, U, and D. Under favorable conditions, submillisecond mixing has been demonstrated in this system. PMID:17940580

Damage detection in composite materials using Lamb wave methods

NASA Astrophysics Data System (ADS)

Kessler, Seth S.; Spearing, S. Mark; Soutis, Constantinos

2002-04-01

Cost-effective and reliable damage detection is critical for the utilization of composite materials. This paper presents part of an experimental and analytical survey of candidate methods for in situ damage detection of composite materials. Experimental results are presented for the application of Lamb wave techniques to quasi-isotropic graphite/epoxy test specimens containing representative damage modes, including delamination, transverse ply cracks and through-holes. Linear wave scans were performed on narrow laminated specimens and sandwich beams with various cores by monitoring the transmitted waves with piezoceramic sensors. Optimal actuator and sensor configurations were devised through experimentation, and various types of driving signal were explored. These experiments provided a procedure capable of easily and accurately determining the time of flight of a Lamb wave pulse between an actuator and sensor. Lamb wave techniques provide more information about damage presence and severity than previously tested methods (frequency response techniques), and provide the possibility of determining damage location due to their local response nature. These methods may prove suitable for structural health monitoring applications since they travel long distances and can be applied with conformable piezoelectric actuators and sensors that require little power.

Performance of Oil Pumping Rings: An Analytical and Experimental Study

NASA Technical Reports Server (NTRS)

Eusepi, M. W.; Walowit, J. A.; Pinkus, O.; Holmes, P.

1986-01-01

A steady-state design computer program was developed to predict the performance of pumping rings as functions of geometry, applied loading, speed, ring modulus, and fluid viscosity. Additional analyses were developed to predict transient behavior of the ring and the effects of temperature rises occurring in the hydrodynamic film between the ring and shaft. The analysis was initially compared with previous experimental data and then used to design additional rings for further testing. Tests were performed with Rulon, carbon-graphite, and babbit rings. The design analysis was used to size all of the rings and to select the ranges of clearances, thickness, and loading. Although full quantitative agreement was lacking, relative agreement existed in that rings that were predicted to perform well theoretically, generally performed well experimentally. Some causes for discrepanices between theory and experiment are believed to be due to starvation, leakage past the secondary seal at high pressures, and uncertainties in the small clearances and local inlet temperatures to the pumping ring. A separate preliminary analysis was performed for a pumping Leningrader seal. This anlaysis can be used to predict the film thickness and flow rate thr ough the seal as a function of pressure, speed, loading, and geometry.

Interactions of spatial strategies producing generalization gradient and blocking: A computational approach

PubMed Central

Dollé, Laurent; Chavarriaga, Ricardo

2018-01-01

We present a computational model of spatial navigation comprising different learning mechanisms in mammals, i.e., associative, cognitive mapping and parallel systems. This model is able to reproduce a large number of experimental results in different variants of the Morris water maze task, including standard associative phenomena (spatial generalization gradient and blocking), as well as navigation based on cognitive mapping. Furthermore, we show that competitive and cooperative patterns between different navigation strategies in the model allow to explain previous apparently contradictory results supporting either associative or cognitive mechanisms for spatial learning. The key computational mechanism to reconcile experimental results showing different influences of distal and proximal cues on the behavior, different learning times, and different abilities of individuals to alternatively perform spatial and response strategies, relies in the dynamic coordination of navigation strategies, whose performance is evaluated online with a common currency through a modular approach. We provide a set of concrete experimental predictions to further test the computational model. Overall, this computational work sheds new light on inter-individual differences in navigation learning, and provides a formal and mechanistic approach to test various theories of spatial cognition in mammals. PMID:29630600

Realistic kinetic loading of the jaw system during single chewing cycles: a finite element study.

PubMed

Martinez Choy, S E; Lenz, J; Schweizerhof, K; Schmitter, M; Schindler, H J

2017-05-01

Although knowledge of short-range kinetic interactions between antagonistic teeth during mastication is of essential importance for ensuring interference-free fixed dental reconstructions, little information is available. In this study, the forces on and displacements of the teeth during kinetic molar biting simulating the power stroke of a chewing cycle were investigated by use of a finite-element model that included all the essential components of the human masticatory system, including an elastic food bolus. We hypothesised that the model can approximate the loading characteristics of the dentition found in previous experimental studies. The simulation was a transient analysis, that is, it considered the dynamic behaviour of the jaw. In particular, the reaction forces on the teeth and joints arose from contact, rather than nodal forces or constraints. To compute displacements of the teeth, the periodontal ligament (PDL) was modelled by use of an Ogden material model calibrated on the basis of results obtained in previous experiments. During the initial holding phase of the power stroke, bite forces were aligned with the roots of the molars until substantial deformation of the bolus occurred. The forces tilted the molars in the bucco-lingual and mesio-distal directions, but as the intrusive force increased the teeth returned to their initial configuration. The Ogden material model used for the PDL enabled accurate prediction of the displacements observed in experimental tests. In conclusion, the comprehensive kinetic finite element model reproduced the kinematic and loading characteristics of previous experimental investigations. © 2017 John Wiley & Sons Ltd.

TAP score: torsion angle propensity normalization applied to local protein structure evaluation

PubMed Central

Tosatto, Silvio CE; Battistutta, Roberto

2007-01-01

Background Experimentally determined protein structures may contain errors and require validation. Conformational criteria based on the Ramachandran plot are mainly used to distinguish between distorted and adequately refined models. While the readily available criteria are sufficient to detect totally wrong structures, establishing the more subtle differences between plausible structures remains more challenging. Results A new criterion, called TAP score, measuring local sequence to structure fitness based on torsion angle propensities normalized against the global minimum and maximum is introduced. It is shown to be more accurate than previous methods at estimating the validity of a protein model in terms of commonly used experimental quality parameters on two test sets representing the full PDB database and a subset of obsolete PDB structures. Highly selective TAP thresholds are derived to recognize over 90% of the top experimental structures in the absence of experimental information. Both a web server and an executable version of the TAP score are available at . Conclusion A novel procedure for energy normalization (TAP) has significantly improved the possibility to recognize the best experimental structures. It will allow the user to more reliably isolate problematic structures in the context of automated experimental structure determination. PMID:17504537

Design, Modeling, Fabrication, and Evaluation of the Air Amplifier for Improved Detection of Biomolecules by Electrospray Ionization Mass Spectrometry

PubMed Central

Robichaud, Guillaume; Dixon, R. Brent; Potturi, Amarnatha S.; Cassidy, Dan; Edwards, Jack R.; Sohn, Alex; Dow, Thomas A.; Muddiman, David C.

2010-01-01

Through a multi-disciplinary approach, the air amplifier is being evolved as a highly engineered device to improve detection limits of biomolecules when using electrospray ionization. Several key aspects have driven the modifications to the device through experimentation and simulations. We have developed a computer simulation that accurately portrays actual conditions and the results from these simulations are corroborated by the experimental data. These computer simulations can be used to predict outcomes from future designs resulting in a design process that is efficient in terms of financial cost and time. We have fabricated a new device with annular gap control over a range of 50 to 70 μm using piezoelectric actuators. This has enabled us to obtain better aerodynamic performance when compared to the previous design (2× more vacuum) and also more reproducible results. This is allowing us to study a broader experimental space than the previous design which is critical in guiding future directions. This work also presents and explains the principles behind a fractional factorial design of experiments methodology for testing a large number of experimental parameters in an orderly and efficient manner to understand and optimize the critical parameters that lead to obtain improved detection limits while minimizing the number of experiments performed. Preliminary results showed that several folds of improvements could be obtained for certain condition of operations (up to 34 folds). PMID:21499524

Intermanual transfer effect in young children after training in a complex skill: mechanistic, pseudorandomized, pretest-posttest study.

PubMed

Romkema, Sietske; Bongers, Raoul M; van der Sluis, Corry K

2015-05-01

Intermanual transfer implies that motor skills learned on one side of the body transfer to the untrained side. This effect was previously noted in adults practicing with a prosthesis simulator. The study objective was to determine whether intermanual transfer is present in children practicing prosthetic handling. A mechanistic, pseudorandomized, pretest-posttest design was used. The study was conducted in a primary school in the Netherlands. The participants were children who were able-bodied (N=48; 25 boys, 23 girls; mean age=5.1 years) and randomly assigned to an experimental group or a control group. The experimental group performed 5 training sessions using a prosthesis simulator on the training arm. Before (pretest), immediately after (posttest), and 6 days after (retention test) the training program, their ability to handle the prosthesis with the contralateral (test) arm was measured. The control group only performed the tests. Half of the children performed the tests with the dominant hand, and the other half performed the tests with the nondominant hand. During the tests, movement time and control of force were measured. An interaction effect of group by test was found for movement time. Post hoc tests revealed significant improvement in the experimental group between the posttest and the retention test. No force control effect was found. Only children who were able-bodied were included. Measurements should have been masked and obtained without tester interference. The fact that 4 children whose results were slower than the mean result discontinued training may have biased the findings. The intermanual transfer effect was present in 5-year-old children undergoing training in prosthetic handling. After training of one hand, children's movement times for the other, untrained hand improved. This finding may be helpful for training children who are novice users of a prosthesis. © 2015 American Physical Therapy Association.

Determination of ultra-short laser induced damage threshold of KH{sub 2}PO{sub 4} crystal: Numerical calculation and experimental verification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, Jian; Department of Physics, The Ohio State University, 191 W. Woodruff Ave, Columbus, OH 43210; Chen, Mingjun, E-mail: chenmj@hit.edu.cn, E-mail: chowdhury.24@osu.edu

Rapid growth and ultra-precision machining of large-size KDP (KH{sub 2}PO{sub 4}) crystals with high laser damage resistance are tough challenges in the development of large laser systems. It is of high interest and practical significance to have theoretical models for scientists and manufacturers to determine the laser-induced damage threshold (LIDT) of actually prepared KDP optics. Here, we numerically and experimentally investigate the laser-induced damage on KDP crystals in ultra-short pulse laser regime. On basis of the rate equation for free electron generation, a model dedicated to predicting the LIDT is developed by considering the synergistic effect of photoionization, impact ionizationmore » and decay of electrons. Laser damage tests are performed to measure the single-pulse LIDT with several testing protocols. The testing results combined with previously reported experimental data agree well with those calculated by the model. By taking the light intensification into consideration, the model is successfully applied to quantitatively evaluate the effect of surface flaws inevitably introduced in the preparation processes on the laser damage resistance of KDP crystals. This work can not only contribute to further understanding of the laser damage mechanisms of optical materials, but also provide available models for evaluating the laser damage resistance of exquisitely prepared optical components used in high power laser systems.« less

Investigating expectation effects using multiple physiological measures

PubMed Central

Siller, Alexander; Ambach, Wolfgang; Vaitl, Dieter

2015-01-01

The study aimed at experimentally investigating whether the human body can anticipate future events under improved methodological conditions. Previous studies have reported contradictory results for the phenomenon typically called presentiment. If the positive findings are accurate, they call into doubt our views about human perception, and if they are inaccurate, a plausible conventional explanation might be based on the experimental design of the previous studies, in which expectation due to item sequences was misinterpreted as presentiment. To address these points, we opted to collect several physiological variables, to test different randomization types and to manipulate subjective significance individually. For the latter, we combined a mock crime scenario, in which participants had to steal specific items, with a concealed information test (CIT), in which the participants had to conceal their knowledge when interrogated about items they had stolen or not stolen. We measured electrodermal activity, respiration, finger pulse, heart rate (HR), and reaction times. The participants (n = 154) were assigned randomly to four different groups. Items presented in the CIT were either drawn with replacement (full) or without replacement (pseudo) and were either presented category-wise (cat) or regardless of categories (nocat). To understand how these item sequences influence expectation and modulate physiological reactions, we compared the groups with respect to effect sizes for stolen vs. not stolen items. Group pseudo_cat yielded the highest effect sizes, and pseudo_nocat yielded the lowest. We could not find any evidence of presentiment but did find evidence of physiological correlates of expectation. Due to the design differing fundamentally from previous studies, these findings do not allow for conclusions on the question whether the expectation bias is being confounded with presentiment. PMID:26500600

Constitutive modeling of polycarbonate over a wide range of strain rates and temperatures

NASA Astrophysics Data System (ADS)

Wang, Haitao; Zhou, Huamin; Huang, Zhigao; Zhang, Yun; Zhao, Xiaoxuan

2017-02-01

The mechanical behavior of polycarbonate was experimentally investigated over a wide range of strain rates (10^{-4} to 5× 103 s^{-1}) and temperatures (293 to 353 K). Compression tests under these conditions were performed using a SHIMADZU universal testing machine and a split Hopkinson pressure bar. Falling weight impact testing was carried out on an Instron Dynatup 9200 drop tower system. The rate- and temperature-dependent deformation behavior of polycarbonate was discussed in detail. Dynamic mechanical analysis (DMA) tests were utilized to observe the glass (α ) transition and the secondary (β ) transition of polycarbonate. The DMA results indicate that the α and β transitions have a dramatic influence on the mechanical behavior of polycarbonate. The decompose/shift/reconstruct (DSR) method was utilized to decompose the storage modulus into the α and β components and extrapolate the entire modulus, the α-component modulus and the β-component modulus. Based on three previous models, namely, Mulliken-Boyce, G'Sell-Jonas and DSGZ, an adiabatic model is proposed to predict the mechanical behavior of polycarbonate. The model considers the contributions of both the α and β transitions to the mechanical behavior, and it has been implemented in ABAQUS/Explicit through a user material subroutine VUMAT. The model predictions are proven to essentially coincide with the experimental results during compression testing and falling weight impact testing.

Influence of coal slurry particle composition on pipeline hydraulic transportation behavior

NASA Astrophysics Data System (ADS)

Li-an, Zhao; Ronghuan, Cai; Tieli, Wang

2018-02-01

Acting as a new type of energy transportation mode, the coal pipeline hydraulic transmission can reduce the energy transportation cost and the fly ash pollution of the conventional coal transportation. In this study, the effect of average velocity, particle size and pumping time on particle composition of coal particles during hydraulic conveying was investigated by ring tube test. Meanwhile, the effects of particle composition change on slurry viscosity, transmission resistance and critical sedimentation velocity were studied based on the experimental data. The experimental and theoretical analysis indicate that the alter of slurry particle composition can lead to the change of viscosity, resistance and critical velocity of slurry. Moreover, based on the previous studies, the critical velocity calculation model of coal slurry is proposed.

KSC-02pd0031

NASA Image and Video Library

2002-01-17

KENNEDY SPACE CENTER, FLA. -- Workers in the Vertical Processing Facility help guide the Near Infrared Camera and Multi-Object Spectrometer (NICMOS) Cooling System onto a payload carrier. NICMOS II is part of the payload on mission STS-109, the Hubble Servicing Telescope Mission. It is a new experimental cooling system consisting of a compressor and tiny turbines. With the experimental cryogenic system, NASA hopes to re-cool the infrared detectors to below -315 degrees F (-193 degrees Celsius). NICMOS II was previously tested aboard STS-95 in 1998. It could extend the life of the Hubble Space Telescope by several years. Astronauts aboard Columbia on mission STS-109 will be replacing the original NICMOS with the newer version. Launch of mission STS-109 is scheduled for Feb. 28, 2002

KSC-02pd0037

NASA Image and Video Library

2002-01-22

KENNEDY SPACE CENTER, FLA. -- The NICMOS II radiator is ready for checkout in the Vertical Processing Facility. The Near Infrared Camera and Multi-Object Spectrometer (NICMOS) Cooling System is part of the payload on mission STS-109, the Hubble Servicing Telescope mission. NICMOS is a new experimental cooling system consisting of a compressor and tiny turbines. With the experimental cryogenic system, NASA hopes to re-cool the infrared detectors to below -315 degrees F (-193 degrees Celsius). NICMOS II was previously tested aboard STS-95 in 1998. NICMOS could extend the life of the Hubble Space Telescope by several years. Astronauts aboard Columbia on mission STS-109 will be replacing the original NICMOS with the newer version. Launch of Columbia is scheduled Feb. 28, 2002

KSC-02pd0040

NASA Image and Video Library

2002-01-22

KENNEDY SPACE CENTER, FLA. -- Workers in the Vertical Processing Facility oversee the installation of the NICMOS radiator onto the MULE (Multi-Use Lightweight Equipment) carrier. Part of the payload on mission STS-109, the Near Infrared Camera and Multi-Object Spectrometer (NICMOS) is a new experimental cooling system consisting of a compressor and tiny turbines. With the experimental cryogenic system, NASA hopes to re-cool the infrared detectors to below -315 degrees F (-193 degrees Celsius). NICMOS II was previously tested aboard STS-95 in 1998. NICMOS could extend the life of the Hubble Space Telescope by several years. Astronauts aboard Columbia on mission STS-109 will be replacing the original NICMOS with the newer version. Launch of Columbia on mission STS-109 is scheduled Feb. 28, 2002

KSC-02pd0033

NASA Image and Video Library

2002-01-17

KENNEDY SPACE CENTER, FLA. -- The Near Infrared Camera and Multi-Object Spectrometer (NICMOS) Cooling System rests inside a protective enclosure on a payload carrier. NICMOS II is part of the payload on mission STS-109, the Hubble Servicing Telescope Mission. It is a new experimental cooling system consisting of a compressor and tiny turbines. With the experimental cryogenic system, NASA hopes to re-cool the infrared detectors to below -315 degrees F (-193 degrees Celsius). NICMOS II was previously tested aboard STS-95 in 1998. It could extend the life of the Hubble Space Telescope by several years. Astronauts aboard Columbia on mission STS-109 will be replacing the original NICMOS with the newer version. Launch of mission STS-109 is scheduled for Feb. 28, 2002

KSC-02pd0025

NASA Image and Video Library

2002-01-17

KENNEDY SPACE CENTER, FLA. -- Workers in the Vertical Processing Facility wheel a container with the NICMOS II across the floor. The Near Infrared Camera and Multi-Object Spectrometer (NICMOS) Cooling System is part of the payload on mission STS-109, the Hubble Servicing Telescope Mission. NICMOS is a new experimental cooling system consisting of a compressor and tiny turbines. With the experimental cryogenic system, NASA hopes to re-cool the infrared detectors to below -315 degrees F (-193 degrees Celsius). NICMOS II was previously tested aboard STS-95 in 1998. It could extend the life of the Hubble Space Telescope by several years. Astronauts aboard Columbia on mission STS-109 will be replacing the original NICMOS with the newer version. Launch of mission STS-109 is scheduled for Feb. 28, 2002

How does social essentialism affect the development of inter-group relations?

PubMed

Rhodes, Marjorie; Leslie, Sarah-Jane; Saunders, Katya; Dunham, Yarrow; Cimpian, Andrei

2018-01-01

Psychological essentialism is a pervasive conceptual bias to view categories as reflecting something deep, stable, and informative about their members. Scholars from diverse disciplines have long theorized that psychological essentialism has negative ramifications for inter-group relations, yet little previous empirical work has experimentally tested the social implications of essentialist beliefs. Three studies (N = 127, ages 4.5-6) found that experimentally inducing essentialist beliefs about a novel social category led children to share fewer resources with category members, but did not lead to the out-group dislike that defines social prejudice. These findings indicate that essentialism negatively influences some key components of inter-group relations, but does not lead directly to the development of prejudice. © 2017 John Wiley & Sons Ltd.

Wavelet transform fast inverse light scattering analysis for size determination of spherical scatterers

PubMed Central

Ho, Derek; Kim, Sanghoon; Drake, Tyler K.; Eldridge, Will J.; Wax, Adam

2014-01-01

We present a fast approach for size determination of spherical scatterers using the continuous wavelet transform of the angular light scattering profile to address the computational limitations of previously developed sizing techniques. The potential accuracy, speed, and robustness of the algorithm were determined in simulated models of scattering by polystyrene beads and cells. The algorithm was tested experimentally on angular light scattering data from polystyrene bead phantoms and MCF-7 breast cancer cells using a 2D a/LCI system. Theoretical sizing of simulated profiles of beads and cells produced strong fits between calculated and actual size (r2 = 0.9969 and r2 = 0.9979 respectively), and experimental size determinations were accurate to within one micron. PMID:25360350

Geophysical investigation of the pressure field produced by water guns at a pond site in La Crosse, Wisconsin

USGS Publications Warehouse

Adams, Ryan F.; Morrow, William S.

2015-09-03

The July 2013 study consisted of three scenarios: fish behavior, single gun assessment, and experimental barrier evaluation. The fish behavior scenario simulated the pond conditions from previous studies. Two 80-in3 water guns were fired in the south end of the testing pond. Pressures essentially doubled from the testing of the single 80-in3 water gun. The single gun assessment scenario sought to replicate the setup of the 80-in3 scenario in September 2012, but with additional sensors to better define the pressure field. The 5-lb/in2 target pressure field continued to show a radius ranging from 40 to 45 feet, dependent on the pressure of the input air. The final scenario, the experimental barrier evaluation, showed that a two-dimensional continuous plane of 5 lb/in2 can be created between two 80-in3 water guns to a separation of 99 feet and a depth of 6.5 feet with 1,500 lb/in2 of input air.

Experimental and analytical dynamic flow characteristics of an axial-flow fan from an air cushion landing system model

NASA Technical Reports Server (NTRS)

Thompson, W. C.; Boghani, A. B.; Leland, T. J. W.

1977-01-01

An investigation was conducted to compare the steady-state and dynamic flow characteristics of an axial-flow fan which had been used previously as the air supply fan for some model air cushion landing system studies. Steady-state flow characteristics were determined in the standard manner by using differential orifice pressures for the flow regime from free flow to zero flow. In this same regime, a correlative technique was established so that fan inlet and outlet pressures could be used to measure dynamic flow as created by a rotating damper. Dynamic tests at damper frequencies up to 5 Hz showed very different flow characteristics when compared with steady-state flow, particularly with respect to peak pressures and the pressure-flow relationship at fan stall and unstall. A generalized, rational mathematical fan model was developed based on physical fan parameters and a steady-state flow characteristic. The model showed good correlation with experimental tests at damper frequencies up to 5 Hz.

Enabling CSPA Operations Through Pilot Involvement in Longitudinal Approach Spacing

NASA Technical Reports Server (NTRS)

Battiste, Vernol (Technical Monitor); Pritchett, Amy

2003-01-01

Several major airports around the United States have, or plan to have, closely-spaced parallel runways. This project complemented current and previous research by examining the pilots ability to control their position longitudinally within their approach stream.This project s results considered spacing for separation from potential positions of wake vortices from the parallel approach. This preventive function could enable CSPA operations to very closely spaced runways. This work also considered how pilot involvement in longitudinal spacing could allow for more efficient traffic flow, by allowing pilots to keep their aircraft within tighter arrival slots then air traffic control (ATC) might be able to establish, and by maintaining space within the arrival stream for corresponding departure slots. To this end, this project conducted several research studies providing an analytic and computational basis for calculating appropriate aircraft spacings, experimental results from a piloted flight simulator test, and an experimental testbed for future simulator tests. The following sections summarize the results of these three efforts.

Short-term effects of different genetically modified maize varieties on arthropod food web properties: an experimental field assessment.

PubMed

Szénási, Ágnes; Pálinkás, Zoltán; Zalai, Mihály; Schmitz, Oswald J; Balog, Adalbert

2014-06-17

There is concern that genetically modified (GM) plants may have adverse affects on the arthropod biodiversity comprising agricultural landscapes. The present study report on a two year field experimental test of whether four different genotypic lines, some are novel with no previous field tests, of GM maize hybrids alter the structure of arthropod food webs that they harbour, relative to non-GM maize (control) that is widely used in agriculture. The different GM genotypes produced either Bt toxins, conferred glyphosate tolerance or a combination of the two traits. Quantitative food web analysis, based on short-term assessment assigning a total of 243,896 arthropod individuals collected from the treatments to their positions in food webs, revealed that complex and stable food webs persisted in each maize treatment. Moreover, food web structure remained relatively unchanged by the GM-genotype. The results suggest that at least in short-term period these particular GM maize genotypes will not have adverse effects on arthropod biota of agricultural landscapes.

GPCR-I-TASSER: A hybrid approach to G protein-coupled receptor structure modeling and the application to the human genome

PubMed Central

Zhang, Jian; Yang, Jianyi; Jang, Richard; Zhang, Yang

2015-01-01

SUMMARY Experimental structure determination remains very difficult for G protein-coupled receptors (GPCRs). We propose a new hybrid protocol to construct GPCR structure models that integrates experimental mutagenesis data with ab initio transmembrane (TM) helix assembly simulations. The method was tested on 24 known GPCRs where the ab initio TM-helix assembly procedure constructed the correct fold for 20 cases. When combined with weak-homology and sparse mutagenesis restraints, the method generated correct folds for all the tested cases with an average C-alpha RMSD 2.4 Å in the TM-regions. The new hybrid protocol was applied to model all 1026 GPCRs in the human genome, where 923 have a high confidence score that are expected to have correct folds; these contain many pharmaceutically important families with no previously solved structures, including Trace amine, Prostanoids, Releasing hormones, Melanocortins, Vasopressin and Neuropeptide Y receptors. The results demonstrate new progress on genome-wide structure modeling of transmembrane proteins. PMID:26190572

Micromechanical Fatigue Visco-Damage Model for Short Glass Fiber Reinforced Polyamide-66

NASA Astrophysics Data System (ADS)

Despringre, N.; Chemisky, Y.; Robert, G.; Meraghni, F.

This work presents a micromechanical fatigue damage model developed for short glass fiber reinforced PA66. It has been developed to predict the high cycle fatigue behavior of PA66/GF30. The model is based on an extended Mori-Tanaka method which includes coated inclusions, matrix viscoelasticity and the evolution of micro-scale damage. The developed model accounts for the nonlinear matrix viscoelasticity and the reinforcement orientation. The description of the damage processes is based on the experimental investigation of damage mechanisms previously performed through in-situ SEM tests and X-ray micro-computed tomography observations. Damage chronologies have been proposed involving three different processes: interface debonding/coating, matrix micro-cracking and fiber breakages. Their occurrence strongly depends on the microstructure and the relative humidity. Each damage mechanism is introduced through an evolution law coupled to local stress fields. The developed model is implemented using a UMAT subroutine. Its experimental validation is achieved under stress or strain controlled fatigue tests.

First experimental evidence of hydrodynamic tunneling of ultra-relativistic protons in extended solid copper target at the CERN HiRadMat facility

NASA Astrophysics Data System (ADS)

Schmidt, R.; Blanco Sancho, J.; Burkart, F.; Grenier, D.; Wollmann, D.; Tahir, N. A.; Shutov, A.; Piriz, A. R.

2014-08-01

A novel experiment has been performed at the CERN HiRadMat test facility to study the impact of the 440 GeV proton beam generated by the Super Proton Synchrotron on extended solid copper cylindrical targets. Substantial hydrodynamic tunneling of the protons in the target material has been observed that leads to significant lengthening of the projectile range, which confirms our previous theoretical predictions [N. A. Tahir et al., Phys. Rev. Spec. Top.-Accel. Beams 15, 051003 (2012)]. Simulation results show very good agreement with the experimental measurements. These results have very important implications on the machine protection design for powerful machines like the Large Hadron Collider (LHC), the future High Luminosity LHC, and the proposed huge 80 km circumference Future Circular Collider, which is currently being discussed at CERN. Another very interesting outcome of this work is that one may also study the field of High Energy Density Physics at this test facility.

Experimental Study and Optimization of Thermoelectricity-Driven Autonomous Sensors for the Chimney of a Biomass Power Plant

NASA Astrophysics Data System (ADS)

Rodríguez, A.; Astrain, D.; Martínez, A.; Aranguren, P.

2014-06-01

In the work discussed in this paper a thermoelectric generator was developed to harness waste heat from the exhaust gas of a boiler in a biomass power plant and thus generate electric power to operate a flowmeter installed in the chimney, to make it autonomous. The main objective was to conduct an experimental study to optimize a previous design obtained after computational work based on a simulation model for thermoelectric generators. First, several places inside and outside the chimney were considered as sites for the thermoelectricity-driven autonomous sensor. Second, the thermoelectric generator was built and tested to assess the effect of the cold-side heat exchanger on the electric power, power consumption by the flowmeter, and transmission frequency. These tests provided the best configuration for the heat exchanger, which met the transmission requirements for different working conditions. The final design is able to transmit every second and requires neither batteries nor electric wires. It is a promising application in the field of thermoelectric generation.

Poisson-Nernst-Planck Models of Nonequilibrium Ion Electrodiffusion through a Protegrin Transmembrane Pore

PubMed Central

Bolintineanu, Dan S.; Sayyed-Ahmad, Abdallah; Davis, H. Ted; Kaznessis, Yiannis N.

2009-01-01

Protegrin peptides are potent antimicrobial agents believed to act against a variety of pathogens by forming nonselective transmembrane pores in the bacterial cell membrane. We have employed 3D Poisson-Nernst-Planck (PNP) calculations to determine the steady-state ion conduction characteristics of such pores at applied voltages in the range of −100 to +100 mV in 0.1 M KCl bath solutions. We have tested a variety of pore structures extracted from molecular dynamics (MD) simulations based on an experimentally proposed octomeric pore structure. The computed single-channel conductance values were in the range of 290–680 pS. Better agreement with the experimental range of 40–360 pS was obtained using structures from the last 40 ns of the MD simulation, where conductance values range from 280 to 430 pS. We observed no significant variation of the conductance with applied voltage in any of the structures that we tested, suggesting that the voltage dependence observed experimentally is a result of voltage-dependent channel formation rather than an inherent feature of the open pore structure. We have found the pore to be highly selective for anions, with anionic to cationic current ratios (ICl−/IK+) on the order of 103. This is consistent with the highly cationic nature of the pore but surprisingly in disagreement with the experimental finding of only slight anionic selectivity. We have additionally tested the sensitivity of our PNP model to several parameters and found the ion diffusion coefficients to have a significant influence on conductance characteristics. The best agreement with experimental data was obtained using a diffusion coefficient for each ion set to 10% of the bulk literature value everywhere inside the channel, a scaling used by several other studies employing PNP calculations. Overall, this work presents a useful link between previous work focused on the structure of protegrin pores and experimental efforts aimed at investigating their conductance characteristics. PMID:19180178

Quantifying microwear on experimental Mistassini quartzite scrapers: preliminary results of exploratory research using LSCM and scale-sensitive fractal analysis.

PubMed

Stemp, W James; Lerner, Harry J; Kristant, Elaine H

2013-01-01

Although previous use-wear studies involving quartz and quartzite have been undertaken by archaeologists, these are comparatively few in number. Moreover, there has been relatively little effort to quantify use-wear on stone tools made from quartzite. The purpose of this article is to determine the effectiveness of a measurement system, laser scanning confocal microscopy (LSCM), to document the surface roughness or texture of experimental Mistassini quartzite scrapers used on two different contact materials (fresh and dry deer hide). As in previous studies using LSCM on chert, flint, and obsidian, this exploratory study incorporates a mathematical algorithm that permits the discrimination of surface roughness based on comparisons at multiple scales. Specifically, we employ measures of relative area (RelA) coupled with the F-test to discriminate used from unused stone tool surfaces, as well as surfaces of quartzite scrapers used on dry and fresh deer hide. Our results further demonstrate the effect of raw material variation on use-wear formation and its documentation using LSCM and RelA. © Wiley Periodicals, Inc.

Mach Probe Measurements in a Large-Scale Helicon Plasma

NASA Astrophysics Data System (ADS)

Hatch, M. W.; Kelly, R. F.; Fisher, D. M.; Gilmore, M.; Dwyer, R. H.

2017-10-01

A new six-tipped Mach probe, that utilizes a fused-quartz insulator, has been developed and initially tested in the HelCat dual-source plasma device at the University of New Mexico. The new design allows for relatively long duration measurements of parallel and perpendicular flows that suffer less from thermal changes in conductivity and surface build-up seen in previous alumina-insulated designs. Mach probe measurement will be presented in comparison with ongoing laser induced fluorescence (LIF) measurements, previous Mach probe measurements, ExB flow estimates derived from Langmuir probes, and fast-frame CCD camera images, in an effort to better understand previous anomalous ion flow in HelCat. Additionally, Mach probe-LIF comparisons will provide an experimentally obtained Mach probe calibration constant, K, to validate sheath-derived estimates for the weakly magnetized case. Supported by U.S. National Science Foundation Award 1500423.

Enhancement of CFD validation exercise along the roof profile of a low-rise building

NASA Astrophysics Data System (ADS)

Deraman, S. N. C.; Majid, T. A.; Zaini, S. S.; Yahya, W. N. W.; Abdullah, J.; Ismail, M. A.

2018-04-01

The aim of this study is to enhance the validation of CFD exercise along the roof profile of a low-rise building. An isolated gabled-roof house having 26.6° roof pitch was simulated to obtain the pressure coefficient around the house. Validation of CFD analysis with experimental data requires many input parameters. This study performed CFD simulation based on the data from a previous study. Where the input parameters were not clearly stated, new input parameters were established from the open literatures. The numerical simulations were performed in FLUENT 14.0 by applying the Computational Fluid Dynamics (CFD) approach based on steady RANS equation together with RNG k-ɛ model. Hence, the result from CFD was analysed by using quantitative test (statistical analysis) and compared with CFD results from the previous study. The statistical analysis results from ANOVA test and error measure showed that the CFD results from the current study produced good agreement and exhibited the closest error compared to the previous study. All the input data used in this study can be extended to other types of CFD simulation involving wind flow over an isolated single storey house.

An Experimental Evaluation of Advanced Rotorcraft Airfoils in the NASA Ames Eleven-foot Transonic Wind Tunnel

NASA Technical Reports Server (NTRS)

Flemming, Robert J.

1984-01-01

Five full scale rotorcraft airfoils were tested in the NASA Ames Eleven-Foot Transonic Wind Tunnel for full scale Reynolds numbers at Mach numbers from 0.3 to 1.07. The models, which spanned the tunnel from floor to ceiling, included two modern baseline airfoils, the SC1095 and SC1094 R8, which have been previously tested in other facilities. Three advanced transonic airfoils, designated the SSC-A09, SSC-A07, and SSC-B08, were tested to confirm predicted performance and provide confirmation of advanced airfoil design methods. The test showed that the eleven-foot tunnel is suited to two-dimensional airfoil testing. Maximum lift coefficients, drag coefficients, pitching moments, and pressure coefficient distributions are presented. The airfoil analysis codes agreed well with the data, with the Grumman GRUMFOIL code giving the best overall performance correlation.

Wall interference correction improvements for the ONERA main wind tunnels

NASA Technical Reports Server (NTRS)

Vaucheret, X.

1982-01-01

This paper describes improved methods of calculating wall interference corrections for the ONERA large windtunnels. The mathematical description of the model and its sting support have become more sophisticated. An increasing number of singularities is used until an agreement between theoretical and experimental signatures of the model and sting on the walls of the closed test section is obtained. The singularity decentering effects are calculated when the model reaches large angles of attack. The porosity factor cartography on the perforated walls deduced from the measured signatures now replaces the reference tests previously carried out in larger tunnels. The porosity factors obtained from the blockage terms (signatures at zero lift) and from the lift terms are in good agreement. In each case (model + sting + test section), wall corrections are now determined, before the tests, as a function of the fundamental parameters M, CS, CZ. During the windtunnel tests, the corrections are quickly computed from these functions.

Taylor Impact Tests and Simulations on PBX 9501

NASA Astrophysics Data System (ADS)

Clements, Brad; Thompson, Darla G.; Luscher, D. J.; Deluca, Racci

2011-06-01

Taylor impact tests have been conducted previously on plastic bonded explosives (PBXs) to characterize the stress state of these materials as they impact smooth and flat steel anvil surfaces at speeds of ~100m/s (i.e. Christopher, et al, 11th Detonation Symposium). In 2003, C. Liu and R. Ellis (unpublished, Los Alamos National Laboratory) performed Taylor tests on PBX 9501 up to speeds of 115 m/s, capturing impact images. In the work presented here, we have extended these tests to velocities of 200 m/s using a composite-lined gun barrel and no specimen sabot. Specimen images are used to validate the thermo-mechanical constitutive model ViscoSCRAM. ViscoSCRAM has been parameterized for PBX 9501 in uniaxial stress configurations. Simulating Taylor impact experiments tests the model in situations undergoing extreme damage. In addition, experimental variations to specimen confinement and friction are introduced in an attempt to establish ignition thresholds in this velocity regime.

QCSEE UTW engine powered-lift acoustic performance

NASA Technical Reports Server (NTRS)

Loeffler, I. J.; Samanich, N. E.; Bloomer, H. E.

1980-01-01

Powered-lift acoustic test of the Quiet Clean Short Haul Experimental Engine (QCSEE) under the wing (UTW) engine are reported. Propulsion systems for two powered-lift concepts were designed, fabricated, and tested. In addition to low noise features, the designs included composite structures, gear-driven fans, digital control, and a variable pitch fan (UTW). The UTW engine was tested in a static ground test facility with wing and flap segments to simulate installation on a short haul transport aircraft of the future. Powered-lift acoustic performance of the UTW engine is compared with that of the previously tested and reported QCSEE over-the-wing (OTW) engine. Both engines were slightly above the noise goal but were significantly below current FAA and modern wide-body jet transport levels. The UTW system in the powered-lift mode was penalized by reflected engine noise from the wing and flap system, while the OTW system was benefitted by a wing noise shielding effect.

Psychology of computer use: IX. A menu of self-administered microcomputer-based neurotoxicology tests

NASA Technical Reports Server (NTRS)

Kennedy, R. S.; Baltzley, D. R.; Wilkes, R. L.; Kuntz, L. A.

1989-01-01

This study examined the feasibility of repeated self-administration of a newly developed battery of mental acuity tests which may have application in screening for fitness-for-duty or for persons who may be exposed to environmental stress, toxic agents, or disease. 16 subjects self-administered 18 microcomputer-based tests (13 new, 5 "core"), without proctors, over 10 sessions. The hardware performed well throughout the study and the tests appeared to be easily self-administered. Stabilities and reliabilities of the tests from the "core" battery were comparable to those obtained previously under more controlled experimental conditions. Eight of the new tests exceeded minimum criteria for metric and practical requirements and can be recommended as additions to the menu. Although the average retest reliability was high, cross-correlations between tests were low, implying factorial diversity. The menu can be used to form batteries with flexible total testing time which are likely to tap different mental processes and functions.

A method for the modelling of porous and solid wind tunnel walls in computational fluid dynamics codes

NASA Technical Reports Server (NTRS)

Beutner, Thomas John

1993-01-01

Porous wall wind tunnels have been used for several decades and have proven effective in reducing wall interference effects in both low speed and transonic testing. They allow for testing through Mach 1, reduce blockage effects and reduce shock wave reflections in the test section. Their usefulness in developing computational fluid dynamics (CFD) codes has been limited, however, by the difficulties associated with modelling the effect of a porous wall in CFD codes. Previous approaches to modelling porous wall effects have depended either upon a simplified linear boundary condition, which has proven inadequate, or upon detailed measurements of the normal velocity near the wall, which require extensive wind tunnel time. The current work was initiated in an effort to find a simple, accurate method of modelling a porous wall boundary condition in CFD codes. The development of such a method would allow data from porous wall wind tunnels to be used more readily in validating CFD codes. This would be beneficial when transonic validations are desired, or when large models are used to achieve high Reynolds numbers in testing. A computational and experimental study was undertaken to investigate a new method of modelling solid and porous wall boundary conditions in CFD codes. The method utilized experimental measurements at the walls to develop a flow field solution based on the method of singularities. This flow field solution was then imposed as a pressure boundary condition in a CFD simulation of the internal flow field. The effectiveness of this method in describing the effect of porosity changes on the wall was investigated. Also, the effectiveness of this method when only sparse experimental measurements were available has been investigated. The current work demonstrated this approach for low speed flows and compared the results with experimental data obtained from a heavily instrumented variable porosity test section. The approach developed was simple, computationally inexpensive, and did not require extensive or intrusive measurements of the boundary conditions during the wind tunnel test. It may be applied to both solid and porous wall wind tunnel tests.

Injury tolerance and moment response of the knee joint to combined valgus bending and shear loading.

PubMed

Bose, Dipan; Bhalla, Kavi S; Untaroiu, Costin D; Ivarsson, B Johan; Crandall, Jeff R; Hurwitz, Shepard

2008-06-01

Valgus bending and shearing of the knee have been identified as primary mechanisms of injuries in a lateral loading environment applicable to pedestrian-car collisions. Previous studies have reported on the structural response of the knee joint to pure valgus bending and lateral shearing, as well as the estimated injury thresholds for the knee bending angle and shear displacement based on experimental tests. However, epidemiological studies indicate that most knee injuries are due to the combined effects of bending and shear loading. Therefore, characterization of knee stiffness for combined loading and the associated injury tolerances is necessary for developing vehicle countermeasures to mitigate pedestrian injuries. Isolated knee joint specimens (n=40) from postmortem human subjects were tested in valgus bending at a loading rate representative of a pedestrian-car impact. The effect of lateral shear force combined with the bending moment on the stiffness response and the injury tolerances of the knee was concurrently evaluated. In addition to the knee moment-angle response, the bending angle and shear displacement corresponding to the first instance of primary ligament failure were determined in each test. The failure displacements were subsequently used to estimate an injury threshold function based on a simplified analytical model of the knee. The validity of the determined injury threshold function was subsequently verified using a finite element model. Post-test necropsy of the knees indicated medial collateral ligament injury consistent with the clinical injuries observed in pedestrian victims. The moment-angle response in valgus bending was determined at quasistatic and dynamic loading rates and compared to previously published test data. The peak bending moment values scaled to an average adult male showed no significant change with variation in the superimposed shear load. An injury threshold function for the knee in terms of bending angle and shear displacement was determined by performing regression analysis on the experimental data. The threshold values of the bending angle (16.2 deg) and shear displacement (25.2 mm) estimated from the injury threshold function were in agreement with previously published knee injury threshold data. The continuous knee injury function expressed in terms of bending angle and shear displacement enabled injury prediction for combined loading conditions such as those observed in pedestrian-car collisions.

Test report on the model 44000 seismometer system

NASA Astrophysics Data System (ADS)

1988-08-01

Teledyne Geotech has completed long period subsurface vault tests on four individual 44000 modules; two horizontal and two vertical. Each type of module is tested in tandem by comparing the outputs of aligned sensors. The latest data is outstanding, particularly that of the horizontal. At a period of 20 seconds, both vertical and horizontal channels show incoherent noise power of approximately-180 dB relative to 1 (m/sec-sq)sq/Hz. At a period of 64 seconds, the horizontal data is some 20 dB quieter than any previous borehole data and furthermore shows no increase with period, even at periods as long as 250 seconds. This performance is remarkable for a non-borehole installation. The vertical data shows excellent performance, although some temperature effects seem to be present. A detailed explanation of the experimental history and current tests follows.

Analytical method for establishing indentation rolling resistance

NASA Astrophysics Data System (ADS)

Gładysiewicz, Lech; Konieczna, Martyna

2018-01-01

Belt conveyors are highly reliable machines able to work in special operating conditions. Harsh environment, long distance of transporting and great mass of transported martials are cause of high energy usage. That is why research in the field of belt conveyor transportation nowadays focuses on reducing the power consumption without lowering their efficiency. In this paper, previous methods for testing rolling resistance are described, and new method designed by authors was presented. New method of testing rolling resistance is quite simple and inexpensive. Moreover it allows to conduct the experimental tests of the impact of different parameters on the value of indentation rolling resistance such as core design, cover thickness, ambient temperature, idler travel frequency, or load value as well. Finally results of tests of relationship between rolling resistance and idler travel frequency and between rolling resistance and idler travel speed was presented.

Computational fluid dynamic modeling of a medium-sized surface mine blasthole drill shroud

PubMed Central

Zheng, Y.; Reed, W.R.; Zhou, L.; Rider, J.P.

2016-01-01

The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) recently developed a series of models using computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a medium-sized surface blasthole drill shroud with a dry dust collector system. Previously run experiments conducted in NIOSH’s full-scale drill shroud laboratory were used to validate the models. The setup values in the CFD models were calculated from experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for several test scenarios, including 0.14 m3/s (300 cfm) and 0.24 m3/s (500 cfm) bailing airflow with 2:1, 3:1 and 4:1 dust collector-to-bailing airflow ratios. For the 2:1 and 3:1 ratios, the calculated dust concentrations from the CFD models were within the 95 percent confidence intervals of the experimental data. This paper describes the methodology used to develop the CFD models, to calculate the model input and to validate the models based on the experimental data. Problem regions were identified and revealed by the study. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. PMID:27932851

Neonicotinoids decrease sucrose responsiveness of honey bees at first contact.

PubMed

Démares, Fabien J; Pirk, Christian W W; Nicolson, Susan W; Human, Hannelie

2018-07-01

For two decades, neonicotinoid insecticides have been extensively used worldwide. Targeting neuronal receptors, they have deleterious effects on the behaviour and physiology of many insects. Bees are exposed to these insecticides in pollen and nectar while providing pollination services to agricultural crops, and neonicotinoids have been shown to impair navigation and decrease their foraging activity. We have previously reported the effect of dietary thiamethoxam on sucrose responsiveness of young worker bees. Here, we exposed caged foragers to sublethal acute doses of clothianidin, imidacloprid, and thiamethoxam, then tested them individually for sucrose responsiveness using standard methods. In addition, we tested the response to a range of sucrose solutions laced with neonicotinoids on bees previously unexposed to neonicotinoids. This paradigm mimics the situation where foragers would first encounter poisoned nectars varying in sugar concentration. Bees were exposed to the insecticides in the feeding solution for 24 h before testing, or in the test solutions, or both. The three compounds had a detrimental effect on responses to mid-to-high sucrose concentrations under all experimental conditions, and unexposed bees tested with laced sucrose displayed unexpected low responses to the higher sucrose concentrations tested. This attenuation of sucrose response is further evidence that neonicotinoids are multisensory disruptors, with potent actions against pollinators and other beneficial insects at first contact. Copyright © 2018 Elsevier Ltd. All rights reserved.

Weighted fusion of depth and inertial data to improve view invariance for real-time human action recognition

NASA Astrophysics Data System (ADS)

Chen, Chen; Hao, Huiyan; Jafari, Roozbeh; Kehtarnavaz, Nasser

2017-05-01

This paper presents an extension to our previously developed fusion framework [10] involving a depth camera and an inertial sensor in order to improve its view invariance aspect for real-time human action recognition applications. A computationally efficient view estimation based on skeleton joints is considered in order to select the most relevant depth training data when recognizing test samples. Two collaborative representation classifiers, one for depth features and one for inertial features, are appropriately weighted to generate a decision making probability. The experimental results applied to a multi-view human action dataset show that this weighted extension improves the recognition performance by about 5% over equally weighted fusion deployed in our previous fusion framework.

An exact stiffness theory for unidirectional xFRP composites

NASA Astrophysics Data System (ADS)

Klasztorny, M.; Konderla, P.; Piekarski, R.

2009-01-01

UD xFRP composites, i.e., isotropic plastics reinforced with long transversely isotropic fibres packed unidirectionally according to the hexagonal scheme are considered. The constituent materials are geometrically and physically linear. The previous formulations of the exact stiffness theory of such composites are revised, and the theory is developed further based on selected boundary-value problems of elasticity theory. The numerical examples presented are focussed on testing the theory with account of previous variants of this theory and experimental values of the effective elastic constants. The authors have pointed out that the exact stiffness theory of UD xFRP composites, with the modifications proposed in our study, will be useful in the engineering practice and in solving the current problems of the mechanics of composite materials.

Identification of genes related to proliferative diabetic retinopathy through RWR algorithm based on protein-protein interaction network.

PubMed

Zhang, Jian; Suo, Yan; Liu, Min; Xu, Xun

2018-06-01

Proliferative diabetic retinopathy (PDR) is one of the most common complications of diabetes and can lead to blindness. Proteomic studies have provided insight into the pathogenesis of PDR and a series of PDR-related genes has been identified but are far from fully characterized because the experimental methods are expensive and time consuming. In our previous study, we successfully identified 35 candidate PDR-related genes through the shortest-path algorithm. In the current study, we developed a computational method using the random walk with restart (RWR) algorithm and the protein-protein interaction (PPI) network to identify potential PDR-related genes. After some possible genes were obtained by the RWR algorithm, a three-stage filtration strategy, which includes the permutation test, interaction test and enrichment test, was applied to exclude potential false positives caused by the structure of PPI network, the poor interaction strength, and the limited similarity on gene ontology (GO) terms and biological pathways. As a result, 36 candidate genes were discovered by the method which was different from the 35 genes reported in our previous study. A literature review showed that 21 of these 36 genes are supported by previous experiments. These findings suggest the robustness and complementary effects of both our efforts using different computational methods, thus providing an alternative method to study PDR pathogenesis. Copyright © 2017 Elsevier B.V. All rights reserved.

Recall of briefly presented chess positions and its relation to chess skill.

PubMed

Gong, Yanfei; Ericsson, K Anders; Moxley, Jerad H

2015-01-01

Individual differences in memory performance in a domain of expertise have traditionally been accounted for by previously acquired chunks of knowledge and patterns. These accounts have been examined experimentally mainly in chess. The role of chunks (clusters of chess pieces recalled in rapid succession during recall of chess positions) and their relations to chess skill are, however, under debate. By introducing an independent chunk-identification technique, namely repeated-recall technique, this study identified individual chunks for particular chess players. The study not only tested chess players with increasing chess expertise, but also tested non-chess players who should not have previously acquired any chess related chunks in memory. For recall of game positions significant differences between players and non-players were found in virtually all the characteristics of chunks recalled. Size of the largest chunks also correlates with chess skill within the group of rated chess players. Further research will help us understand how these memory encodings can explain large differences in chess skill.

Recall of Briefly Presented Chess Positions and Its Relation to Chess Skill

PubMed Central

Moxley, Jerad H.

2015-01-01

Individual differences in memory performance in a domain of expertise have traditionally been accounted for by previously acquired chunks of knowledge and patterns. These accounts have been examined experimentally mainly in chess. The role of chunks (clusters of chess pieces recalled in rapid succession during recall of chess positions) and their relations to chess skill are, however, under debate. By introducing an independent chunk-identification technique, namely repeated-recall technique, this study identified individual chunks for particular chess players. The study not only tested chess players with increasing chess expertise, but also tested non-chess players who should not have previously acquired any chess related chunks in memory. For recall of game positions significant differences between players and non-players were found in virtually all the characteristics of chunks recalled. Size of the largest chunks also correlates with chess skill within the group of rated chess players. Further research will help us understand how these memory encodings can explain large differences in chess skill. PMID:25774693

A field trial of ethyl hexanediol against Aedes dorsalis in Sonoma County, California.

PubMed

Rutledge, L C; Hooper, R L; Wirtz, R A; Gupta, R K

1989-09-01

The repellent ethyl hexanediol (2-ethyl-1,3-hexanediol) was tested against the mosquito Aedes dorsalis in a coastal salt marsh in California. The experimental design incorporated a linear regression model, sequential treatments and a proportional end point (95%) for protection time. The protection time of 0.10 mg/cm2 ethyl hexanediol was estimated at 0.8 h. This time is shorter than that obtained previously for deet (N,N-diethyl-3-methylbenzamide) against Ae. dorsalis (4.4 h).

Hypothesis Testing of Edge Organizations: Empirically Calibrating an Organizational Model for Experimentation

DTIC Science & Technology

2007-06-01

LIMITATION OF ABSTRACT Same as Report (SAR) 18. NUMBER OF PAGES 63 19a. NAME OF RESPONSIBLE PERSON a. REPORT unclassified b . ABSTRACT...section discusses previous efforts to model and compare knowledge flows between Edge and Hierarchy organizations. B ackground Individual...and Ebbinghaus, 1913), e.g.: R(t) = at- b where t is time and a and b are scalars (see Figure 2). 4 0 0.5 1 1.5 2 2.5 3 3.5 4 0 5 10 15 Delay in

Advanced Hybrid Modeling of Hall Thruster Plumes

DTIC Science & Technology

2010-06-16

Hall thruster operated in the Large Vacuum Test Facility at the University of Michigan. The approach utilizes the direct simulation Monte Carlo method and the Particle-in-Cell method to simulate the collision and plasma dynamics of xenon neutrals and ions. The electrons are modeled as a fluid using conservation equations. A second code is employed to model discharge chamber behavior to provide improved input conditions at the thruster exit for the plume simulation. Simulation accuracy is assessed using experimental data previously

Spin Seebeck effect in a simple ferromagnet near T c: a Ginzburg-Landau approach

NASA Astrophysics Data System (ADS)

Adachi, Hiroto; Yamamoto, Yutaka; Ichioka, Masanori

2018-04-01

A time-dependent Ginzburg-Landau theory is used to examine the longitudinal spin Seebeck effect in a simple ferromagnet in the vicinity of the Curie temperature T c. It is shown analytically that the spin Seebeck effect is proportional to the magnetization near T c, whose result is in line with the previous numerical finding. It is argued that the present result can be tested experimentally using a simple magnetic system such as EuO/Pt or EuS/Pt.

Report on Recent Upgrades to the Curved Duct Test Rig at NASA Langley Research Center

NASA Technical Reports Server (NTRS)

Gerhold, Carl H.; Brown, Martha C.; Jones, Michael G.; Howerton, Brian M.

2011-01-01

The Curved Duct Test Rig (CDTR) is an experimental facility that is designed to assess the acoustic and aerodynamic performance of aircraft engine nacelle liners in close to full scale. The test section is between 25% and 100% of the scale of aft bypass ducts of aircraft engines ranging in size from business jet to large commercial passenger jet. The CDTR has been relocated and now shares space with the Grazing Flow Impedance Tube in the Liner Technology Facility at NASA Langley Research Center. As a result of the relocation, research air is supplied to the CDTR from a 50,000 cfm centrifugal fan. This new air supply enables testing of acoustic liner samples at up to Mach 0.500. This paper documents experiments and analysis on a baseline liner sample, which the authors had analyzed and reported on prior to the move to the new facility. In the present paper, the experimental results are compared to those obtained previously in order to ensure continuity of the experimental capability. Experiments that take advantage of the facility s expanded capabilities are also reported. Data analysis features that enhance understanding of the physical properties of liner performance are introduced. The liner attenuation is shown to depend on the mode that is incident on the liner test section. The relevant parameter is the mode cut-on ratio, which determines the angle at which the sound wave is incident on the liner surface. The scattering of energy from the incident mode into higher order, less attenuated modes is demonstrated. The configuration of the acoustic treatment, in this case lined on one surface and hard wall on the opposite surface, is shown to affect the mode energy redistribution.

Trapezoidal Wing Experimental Repeatability and Velocity Profiles in the 14- by 22-Foot Subsonic Tunnel

NASA Technical Reports Server (NTRS)

Hannon, Judith A.; Washburn, Anthony E.; Jenkins, Luther N.; Watson, Ralph D.

2012-01-01

The AIAA Applied Aerodynamics Technical Committee sponsored a High Lift Prediction Workshop held in June 2010. For this first workshop, data from the Trapezoidal Wing experiments were used for comparison to CFD. This paper presents long-term and short-term force and moment repeatability analyses for the Trapezoidal Wing model tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel. This configuration was chosen for its simplified high-lift geometry, publicly available set of test data, and previous CFD experience with this configuration. The Trapezoidal Wing is a three-element semi-span swept wing attached to a body pod. These analyses focus on configuration 1 tested in 1998 (Test 478), 2002 (Test 506), and 2003 (Test 513). This paper also presents model velocity profiles obtained on the main element and on the flap during the 1998 test. These velocity profiles are primarily at an angle of attack of 28 degrees and semi-span station of 83% and show confluent boundary layers and wakes.

The experimentation of LC7E learning model on the linear program material in terms of interpersonal intelligence on Wonogiri vocational school students

NASA Astrophysics Data System (ADS)

Antinah; Kusmayadi, T. A.; Husodo, B.

2018-05-01

This study aims to determine the effect of learning model on student achievement in terms of interpersonal intelligence. The compared learning models are LC7E and Direct learning model. This type of research is a quasi-experimental with 2x3 factorial design. The population in this study is a Grade XI student of Wonogiri Vocational Schools. The sample selection had done by stratified cluster random sampling. Data collection technique used questionnaires, documentation and tests. The data analysis technique used two different unequal cell variance analysis which previously conducted prerequisite analysis for balance test, normality test and homogeneity test. he conclusions of this research are: 1) student learning achievement of mathematics given by LC7E learning model is better when compared with direct learning; 2) Mathematics learning achievement of students who have a high level of interpersonal intelligence is better than students with interpersonal intelligence in medium and low level. Students' mathematics learning achievement with interpersonal level of intelligence is better than those with low interpersonal intelligence on linear programming; 3) LC7E learning model resulted better on mathematics learning achievement compared with direct learning model for each category of students’ interpersonal intelligence level on linear program material.

The experimentation of LC7E learning model on the linear program material in terms of interpersonal intelligence on Wonogiri Vocational School students

NASA Astrophysics Data System (ADS)

Antinah; Kusmayadi, T. A.; Husodo, B.

2018-03-01

This study aimed to determine the effect of learning model on student achievement in terms of interpersonal intelligence. The compared learning models are LC7E and Direct learning model. This type of research is a quasi-experimental with 2x3 factorial design. The population in this study is a Grade XI student of Wonogiri Vocational Schools. The sample selection had done by stratified cluster random sampling. Data collection technique used questionnaires, documentation and tests. The data analysis technique used two different unequal cell variance analysis which previously conducted prerequisite analysis for balance test, normality test and homogeneity test. he conclusions of this research are: 1) student learning achievement of mathematics given by LC7E learning model is better when compared with direct learning; 2) Mathematics learning achievement of students who have a high level of interpersonal intelligence is better than students with interpersonal intelligence in medium and low level. Students’ mathematics learning achievement with interpersonal level of intelligence is better than those with low interpersonal intelligence on linear programming; 3) LC7E learning model resulted better on mathematics learning achievement compared with direct learning model for each category of students’ interpersonal intelligence level on linear program material.

Auditory-visual speech integration by prelinguistic infants: perception of an emergent consonant in the McGurk effect.

PubMed

Burnham, Denis; Dodd, Barbara

2004-12-01

The McGurk effect, in which auditory [ba] dubbed onto [ga] lip movements is perceived as "da" or "tha," was employed in a real-time task to investigate auditory-visual speech perception in prelingual infants. Experiments 1A and 1B established the validity of real-time dubbing for producing the effect. In Experiment 2, 4 1/2-month-olds were tested in a habituation-test paradigm, in which an auditory-visual stimulus was presented contingent upon visual fixation of a live face. The experimental group was habituated to a McGurk stimulus (auditory [ba] visual [ga]), and the control group to matching auditory-visual [ba]. Each group was then presented with three auditory-only test trials, [ba], [da], and [(delta)a] (as in then). Visual-fixation durations in test trials showed that the experimental group treated the emergent percept in the McGurk effect, [da] or [(delta)a], as familiar (even though they had not heard these sounds previously) and [ba] as novel. For control group infants [da] and [(delta)a] were no more familiar than [ba]. These results are consistent with infants' perception of the McGurk effect, and support the conclusion that prelinguistic infants integrate auditory and visual speech information. Copyright 2004 Wiley Periodicals, Inc.

Static Stretching Alters Neuromuscular Function and Pacing Strategy, but Not Performance during a 3-Km Running Time-Trial

PubMed Central

Damasceno, Mayara V.; Duarte, Marcos; Pasqua, Leonardo A.; Lima-Silva, Adriano E.; MacIntosh, Brian R.; Bertuzzi, Rômulo

2014-01-01

Purpose Previous studies report that static stretching (SS) impairs running economy. Assuming that pacing strategy relies on rate of energy use, this study aimed to determine whether SS would modify pacing strategy and performance in a 3-km running time-trial. Methods Eleven recreational distance runners performed a) a constant-speed running test without previous SS and a maximal incremental treadmill test; b) an anthropometric assessment and a constant-speed running test with previous SS; c) a 3-km time-trial familiarization on an outdoor 400-m track; d and e) two 3-km time-trials, one with SS (experimental situation) and another without (control situation) previous static stretching. The order of the sessions d and e were randomized in a counterbalanced fashion. Sit-and-reach and drop jump tests were performed before the 3-km running time-trial in the control situation and before and after stretching exercises in the SS. Running economy, stride parameters, and electromyographic activity (EMG) of vastus medialis (VM), biceps femoris (BF) and gastrocnemius medialis (GA) were measured during the constant-speed tests. Results The overall running time did not change with condition (SS 11:35±00:31 s; control 11:28±00:41 s, p = 0.304), but the first 100 m was completed at a significantly lower velocity after SS. Surprisingly, SS did not modify the running economy, but the iEMG for the BF (+22.6%, p = 0.031), stride duration (+2.1%, p = 0.053) and range of motion (+11.1%, p = 0.0001) were significantly modified. Drop jump height decreased following SS (−9.2%, p = 0.001). Conclusion Static stretch impaired neuromuscular function, resulting in a slow start during a 3-km running time-trial, thus demonstrating the fundamental role of the neuromuscular system in the self-selected speed during the initial phase of the race. PMID:24905918

Specific Hardening Function Definition and Characterization of a Multimechanism Generalized Potential-based Viscoelastoplasticity Model

NASA Technical Reports Server (NTRS)

Arnold, S. M.; Saleeb, A. F.

2003-01-01

Given the previous complete-potential structure framework together with the notion of strain- and stress-partitioning in terms of separate contributions of several submechanisms (viscoelastic and viscoplastic) to the thermodynamic functions (stored energy and dissipation) a detailed viscoelastoplastic multimechanism characterization of a specific hardening functional form of the model is presented and discussed. TIMETAL 21S is the material of choice as a comprehensive test matrix, including creep, relaxation, constant strain-rate tension tests, etc. are available at various temperatures. Discussion of these correlations tests, together with comparisons to several other experimental results, are given to assess the performance and predictive capabilities of the present model particularly with regard to the notion of hardening saturation as well as the interaction of multiplicity of dissipative (reversible/irreversible) mechanisms.

Hypersonic Wind Tunnel Test of a Flare-type Membrane Aeroshell for Atmospheric Entry Capsules

NASA Astrophysics Data System (ADS)

Yamada, Kazuhiko; Koyama, Masashi; Kimura, Yusuke; Suzuki, Kojiro; Abe, Takashi; Koichi Hayashi, A.

A flexible aeroshell for atmospheric entry vehicles has attracted attention as an innovative space transportation system. In this study, hypersonic wind tunnel tests were carried out to investigate the behavior, aerodynamic characteristics and aerodynamic heating environment in hypersonic flow for a previously developed capsule-type vehicle with a flare-type membrane aeroshell made of ZYLON textile sustained by a rigid torus frame. Two different models with different flare angles (45º and 60º) were tested to experimentally clarify the effect of flare angle. Results indicate that flare angle of aeroshell has significant and complicate effect on flow field and aerodynamic heating in hypersonic flow at Mach 9.45 and the flare angle is very important parameter for vehicle design with the flare-type membrane aeroshell.

Impact of suggestion on the human experimental model of cold hyperalgesia after topical application of high-concentration menthol [40%].

PubMed

Helfert, S; Reimer, M; Barnscheid, L; Hüllemann, P; Rengelshausen, J; Keller, T; Baron, R; Binder, A

2018-05-14

Human experimental pain models in healthy subjects offer unique possibilities to study mechanisms of pain within a defined setting of expected pain symptoms, signs and mechanisms. Previous trials in healthy subjects demonstrated that topical application of 40% menthol is suitable to induce cold hyperalgesia. The objective of this study was to evaluate the impact of suggestion on this experimental human pain model. The study was performed within a single-centre, randomized, placebo-controlled, double-blind, two-period crossover trial in a cohort of 16 healthy subjects. Subjects were tested twice after topical menthol application (40% dissolved in ethanol) and twice after ethanol (as placebo) application. In the style of a balanced placebo trial design, the subjects received during half of the testing the correct information about the applied substance (topical menthol or ethanol) and during half of the testing the incorrect information, leading to four tested conditions (treatment conditions: menthol-told-menthol and menthol-told-ethanol; placebo conditions: ethanol-told-menthol and ethanol-told-ethanol). Cold but not mechanical hyperalgesia was reliably induced by the model. The cold pain threshold decreased in both treatment conditions regardless whether true or false information was given. Minor suggestion effects were found in subjects with prior ethanol application. The menthol model is a reliable, nonsuggestible model to induce cold hyperalgesia. Mechanical hyperalgesia is not as reliable to induce. Cold hyperalgesia may be investigated under unbiased and suggestion-free conditions using the menthol model of pain. © 2018 European Pain Federation - EFIC®.

Effect of Favorable Pressure Gradients on Turbine Blade Pressure Surface Heat Transfer

NASA Technical Reports Server (NTRS)

Boyle, Robert J.; Giel, P. W.

2002-01-01

Recent measurements on a turbine rotor showed significant relaminarization effects. These effects were evident on the pressure surface heat transfer measurements. The character of the heat transfer varied with Reynolds number. Data were obtained for exit Reynolds numbers between 500,000 and 880,000. Tests were done with a high level of inlet turbulence, 7.5%. At lower Reynolds numbers the heat transfer was similar to that for laminar flow, but at a level higher than for laminar flow. At higher Reynolds numbers the heat transfer was similar to turbulent flow, when the acceleration parameter, K, was sufficiently small. The proposed paper discusses the experimental results, and also discusses approaches to calculating the surface heat transfer for the blade surface. Calculations were done using a three-dimensional Navier-Stokes CFD analysis. The results of these tests, when compared with previous blade tests in the same facility, illustrate modeling difficulties that were encountered in CFD predictions. The two blades were in many ways similar. However, the degree of agreement between the same analysis and the experimental data was significantly different. These differences are highlighted to illustrate where improvements in modeling approaches are needed for transitional flows.

An experimental investigation of the structural dynamics of a torsionally soft rotor in vacuum

NASA Technical Reports Server (NTRS)

Srinivasan, A. V.; Cutts, D. G.; Shu, H. T.

1986-01-01

An extensive data base of structural dynamic characteristics has been generated from an experimental program conducted on a torsionally soft two-bladed model helicopter rotor system. Measurements of vibratory strains for five modes of vibration were made at twenty-one locations on the two blades at speeds varying from 0 to 1000 RPM and for several combinations of precone, droop and flexure stiffness. Tests were conducted in vacuum under carefully controlled conditions using a unique excitation device with a system of piezoelectric crystals bonded to the blade surface near the root. Frequencies, strain mode shapes and dampings are extracted from the time histories and can be used to validate structural dynamics codes. The dynamics of the system are such that there is a clear tendency for the first torsion and second flap modes to couple within the speed range considered. Strain mode shapes vary significantly with speed and configuration. This feature is important in the calcualtion of aeroelastic instabilities. The tension axis tests confirmed that the modulus-weighted centroid for the nonhomogeneous airfoil is slightly off the mass centroid and validated previous static tests done to determine location of the tension axis.

Musical plus phonological input for young foreign language readers

PubMed Central

Fonseca-Mora, M. C.; Jara-Jiménez, Pilar; Gómez-Domínguez, María

2015-01-01

Based on previous studies showing that phonological awareness is related to reading abilities and that music training improves phonological processing, the aim of the present study was to test for the efficiency of a new method for teaching to read in a foreign language. Specifically, we tested the efficacy of a phonological training program, with and without musical support that aimed at improving early reading skills in 7–8-year-old Spanish children (n = 63) learning English as a foreign language. Of interest was also to explore the impact of this training program on working memory and decoding skills. To achieve these goals we tested three groups of children before and after training: a control group, an experimental group with phonological non-musical intervention (active control), and an experimental group with musical intervention. Results clearly point to the beneficial effects of the phonological teaching approach but the further impact of the music support was not demonstrated. Moreover, while children in the music group showed low musical aptitudes before training, they nevertheless performed better than the control group. Therefore, the phonological training program with and without music support seem to have significant effects on early reading skills. PMID:25852604

Experimental testing of a new integrated model of the budding yeast Start transition

PubMed Central

Adames, Neil R.; Schuck, P. Logan; Chen, Katherine C.; Murali, T. M.; Tyson, John J.; Peccoud, Jean

2015-01-01

The cell cycle is composed of bistable molecular switches that govern the transitions between gap phases (G1 and G2) and the phases in which DNA is replicated (S) and partitioned between daughter cells (M). Many molecular details of the budding yeast G1–S transition (Start) have been elucidated in recent years, especially with regard to its switch-like behavior due to positive feedback mechanisms. These results led us to reevaluate and expand a previous mathematical model of the yeast cell cycle. The new model incorporates Whi3 inhibition of Cln3 activity, Whi5 inhibition of SBF and MBF transcription factors, and feedback inhibition of Whi5 by G1–S cyclins. We tested the accuracy of the model by simulating various mutants not described in the literature. We then constructed these novel mutant strains and compared their observed phenotypes to the model’s simulations. The experimental results reported here led to further changes of the model, which will be fully described in a later article. Our study demonstrates the advantages of combining model design, simulation, and testing in a coordinated effort to better understand a complex biological network. PMID:26310445

Musical plus phonological input for young foreign language readers.

PubMed

Fonseca-Mora, M C; Jara-Jiménez, Pilar; Gómez-Domínguez, María

2015-01-01

Based on previous studies showing that phonological awareness is related to reading abilities and that music training improves phonological processing, the aim of the present study was to test for the efficiency of a new method for teaching to read in a foreign language. Specifically, we tested the efficacy of a phonological training program, with and without musical support that aimed at improving early reading skills in 7-8-year-old Spanish children (n = 63) learning English as a foreign language. Of interest was also to explore the impact of this training program on working memory and decoding skills. To achieve these goals we tested three groups of children before and after training: a control group, an experimental group with phonological non-musical intervention (active control), and an experimental group with musical intervention. Results clearly point to the beneficial effects of the phonological teaching approach but the further impact of the music support was not demonstrated. Moreover, while children in the music group showed low musical aptitudes before training, they nevertheless performed better than the control group. Therefore, the phonological training program with and without music support seem to have significant effects on early reading skills.

Improved test of Lorentz invariance in electrodynamics

NASA Astrophysics Data System (ADS)

Wolf, Peter; Bize, Sébastien; Clairon, André; Santarelli, Giorgio; Tobar, Michael E.; Luiten, André N.

2004-09-01

We report new results of a test of Lorentz invariance based on the comparison of a cryogenic sapphire microwave resonator and a hydrogen-maser. The experimental results are shown together with an extensive analysis of systematic effects. Previously, this experiment has set the most stringent constraint on Kennedy-Thorndike type violations of Lorentz invariance. In this work we present new data and interpret our results in the general Lorentz violating extension of the standard model of particle physics (SME). Within the photon sector of the SME, our experiment is sensitive to seven SME parameters. We marginally improve present limits on four of these, and by a factor seven to ten on the other three.

Relatedness decreases and reciprocity increases cooperation in Norway rats.

PubMed

Schweinfurth, Manon K; Taborsky, Michael

2018-03-14

Kin selection and reciprocity are two mechanisms underlying the evolution of cooperation, but the relative importance of kinship and reciprocity for decisions to cooperate are yet unclear for most cases of cooperation. Here, we experimentally tested the relative importance of relatedness and received cooperation for decisions to help a conspecific in wild-type Norway rats ( Rattus norvegicus ). Test rats provided more food to non-kin than to siblings, and they generally donated more food to previously helpful social partners than to those that had refused help. The rats thus applied reciprocal cooperation rules irrespective of relatedness, highlighting the importance of reciprocal help for cooperative interactions among both related and unrelated conspecifics. © 2018 The Author(s).

Observations of directional gamma prime coarsening during engine operation

NASA Astrophysics Data System (ADS)

Draper, S.; Hull, D.; Dreshfield, R.

1989-04-01

Two alloys, NASAIR 100 and a modified NASAIR 100 called Alloy 3, were run as turbine blades in an experimental ground-based Garrett TFE731 engine for up to 200 hours. The stress induced directional coarsening of γ' (rafting) that developed during engine testing was analyzed and compared to previous research from laboratory tests. The blades were found to have formed a lamellar structure, the lamellae being normal to the centrifugal stress axis over much of the span. However, near the surfaces, the blades were found to have formed lamellae parallel to the centrifugal stress axis for certain cycles. Representative photomicrographs of the blades and the effects of stress and temperature on lamellae formation are shown.

Observations of directional gamma prime coarsening during engine operation

NASA Technical Reports Server (NTRS)

Draper, Susan L.; Hull, David R.; Dreshfield, Robert L.

1987-01-01

Two alloys with negative mismatch parameters, NASAIR 100 and a modified NASAIR 100 called Alloy 3 were run as turbine blades in an experimental ground based Garret TFE731 engine for up to 200 hr. The directional coarsening of gamma prime (rafting) that developed during engine testing was analyzed and compared to previous research from laboratory tests. The blades were found to be rafted normal to the centrifugal stress axis over much of the span, but near the surfaces, the blades were found to be rafted parallel to the centrifugal stress axis for certain cycles. Representative photomicrographs of the blades and the effects of stress and temperature on raft formation are shown.

Observations of directional gamma prime coarsening during engine operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Draper, S.L.; Hull, D.R.; Dreshfield, R.L.

1987-02-01

Two alloys with negative mismatch parameters, NASAIR 100 and a modified NASAIR 100 called Alloy 3 were run as turbine blades in an experimental ground based Garret TFE731 engine for up to 200 hr. The directional coarsening of gamma prime (rafting) that developed during engine testing was analyzed and compared to previous research from laboratory tests. The blades were found to be rafted normal to the centrifugal stress axis over much of the span, but near the surfaces, the blades were found to be rafted parallel to the centrifugal stress axis for certain cycles. Representative photomicrographs of the blades andmore » the effects of stress and temperature on raft formation are shown.« less

Observations of directional gamma prime coarsening during engine operation

NASA Technical Reports Server (NTRS)

Draper, S.; Hull, D.; Dreshfield, R.

1989-01-01

Two alloys, NASAIR 100 and a modified NASAIR 100 called Alloy 3, were run as turbine blades in an experimental ground-based Garrett TFE731 engine for up to 200 hours. The stress induced directional coarsening of gamma-prime (rafting) that developed during engine testing was analyzed and compared to previous research from laboratory tests. The blades were found to have formed a lamellar structure, the lamellae being normal to the centrifugal stress axis over much of the span. However, near the surfaces, the blades were found to have formed lamellae parallel to the centrifugal stress axis for certain cycles. Representative photomicrographs of the blades and the effects of stress and temperature on lamellae formation are shown.

Experimental evaluation of x-ray acoustic computed tomography for radiotherapy dosimetry applications.

PubMed

Hickling, Susannah; Lei, Hao; Hobson, Maritza; Léger, Pierre; Wang, Xueding; El Naqa, Issam

2017-02-01

The aim of this work was to experimentally demonstrate the feasibility of x-ray acoustic computed tomography (XACT) as a dosimetry tool in a clinical radiotherapy environment. The acoustic waves induced following a single pulse of linear accelerator irradiation in a water tank were detected with an immersion ultrasound transducer. By rotating the collimator and keeping the transducer stationary, acoustic signals at varying angles surrounding the field were detected and reconstructed to form an XACT image. Simulated XACT images were obtained using a previously developed simulation workflow. Profiles extracted from experimental and simulated XACT images were compared to profiles measured with an ion chamber. A variety of radiation field sizes and shapes were investigated. XACT images resembling the geometry of the delivered radiation field were obtained for fields ranging from simple squares to more complex shapes. When comparing profiles extracted from simulated and experimental XACT images of a 4 cm × 4 cm field, 97% of points were found to pass a 3%/3 mm gamma test. Agreement between simulated and experimental XACT images worsened when comparing fields with fine details. Profiles extracted from experimental XACT images were compared to profiles obtained through clinical ion chamber measurements, confirming that the intensity of XACT images is related to deposited radiation dose. Seventy-seven percent of the points in a profile extracted from an experimental XACT image of a 4 cm × 4 cm field passed a 7%/4 mm gamma test when compared to an ion chamber measured profile. In a complicated puzzle-piece shaped field, 86% of the points in an XACT extracted profile passed a 7%/4 mm gamma test. XACT images with intensity related to the spatial distribution of deposited dose in a water tank were formed for a variety of field sizes and shapes. XACT has the potential to be a useful tool for absolute, relative and in vivo dosimetry. © 2016 American Association of Physicists in Medicine.

The Effect of Phosphatidylcholine and Deoxycholate Compound Injections to the Localized Adipose Tissue: An Experimental Study with a Murine Model

PubMed Central

Noh, Yongjoon

2012-01-01

Background Phosphatidylcholine (PPC) and deoxycholate (DCA) compound has been recently used for the purpose of partial lipolysis and is valued for its efficacy and lower invasiveness compared to liposuction and dermolipectomy used previously. In this article, the authors discuss the efficacy of the PPC dissolved in DCA via an experimental rat study model, along with suggesting a useful animal experimental model for the study of adipose tissue and lipolysis. Methods Bilateral inguinal fat pads of an experimental rat were elevated with the deep inferior epigastric vessel as the sole vascular pedicle. Normal saline was injected on one side as a control group and a PPC and DCA compound was injected on the other side. After 4 days, the rats were euthanized for microscopic tissue examination. The pathology was scored by a semiquantitative system in 4 categories: normal fat amount, fat necrosis, inflammatory activity, and stage of fibrosis. A Wilcoxon signed-rank test powered by SPSS packet program was used for statistical analysis and to determine significance. Results Microscopic examination was performed on the obtained samples, and the experimental data of all four categories showed significant histologic differences compared to the control group. All of the data also showed statistical significance by the Wilcoxon signedrank test (P<0.01). Conclusions In the inguinal fat pad rat model, the control group and the experimental group had a differed significantly in the amount of normal fat tissue, inflammation, necrosis, and fibrosis. We recommend the rat inguinal fat pad model used in this study, as it is likely to be useful in related research. PMID:23094238

Detection of Subsurface Material Separation in Shuttle Orbiter Slip-Side Joggle Region of the Wing Leading Edge using Infrared Imaging Data from Arc Jet Tests

NASA Technical Reports Server (NTRS)

Daryabeigi, Kamran; Walker, Sandra P.

2009-01-01

The objective of the present study was to determine whether infrared imaging (IR) surface temperature data obtained during arc-jet tests of Space Shuttle Orbiter s reinforced carbon-carbon (RCC) wing leading edge panel slip-side joggle region could be used to detect presence of subsurface material separation, and if so, to determine when separation occurs during the simulated entry profile. Recent thermostructural studies have indicated thermally induced interlaminar normal stress concentrations at the substrate/coating interface in the curved joggle region can result in local subsurface material separation, with the separation predicted to occur during approach to peak heating during reentry. The present study was an attempt to determine experimentally when subsurface material separations occur. A simplified thermal model of a flat RCC panel with subsurface material separation was developed and used to infer general surface temperature trends due to the presence of subsurface material separation. IR data from previously conducted arc-jet tests on three test specimens were analyzed: one without subsurface material separation either pre or post test, one with pre test separation, and one with separation developing during test. The simplified thermal model trend predictions along with comparison of experimental IR data of the three test specimens were used to successfully infer material separation from the arc-jet test data. Furthermore, for the test specimen that had developed subsurface material separation during the arc-jet tests, the initiation of separation appeared to occur during the ramp up to the peak heating condition, where test specimen temperature went from 2500 to 2800 F.

Sex Differences in Experimental and Clinical Pain Sensitivity for Patients with Shoulder Pain

PubMed Central

Kindler, Lindsay L.; Valencia, Carolina; Fillingim, Roger B.; George, Steven Z.

2010-01-01

Previous research demonstrates that men and women differ in the way that they perceive and process pain. Much of this work has been done in healthy adults with a lack of consensus in clinical pain populations. The purpose of this study was to investigate how men and women with shoulder pain differ in their experience of experimental and clinical pain and whether psychological processes differentially affect these responses. Fifty nine consecutive subjects (24 women, 35 men) seeking operative treatment for shoulder pain were enrolled in this study. Subjects completed self report questionnaires to assess clinical pain, catastrophizing, anxiety and depression and underwent a series of experimental pain tests consisting of pressure pain, thermal pain (threshold and tolerance), and thermal temporal summation. Results indicated that women experienced greater clinical pain and enhanced sensitivity to pressure pain. Age did not affect the observed sex differences. There were no sex differences in psychological association with experimental and clinical pain in this cohort. The relationship between clinical and experimental pressure pain was stronger in women as compared to men. These findings offer insight into the interactions between biological and psychosocial influences of pain and how these interactions vary by sex. PMID:20598598

True detection limits in an experimental linearly heteroscedastic system.. Part 2

NASA Astrophysics Data System (ADS)

Voigtman, Edward; Abraham, Kevin T.

2011-11-01

Despite much different processing of the experimental fluorescence detection data presented in Part 1, essentially the same estimates were obtained for the true theoretical Currie decision levels ( YC and XC) and true Currie detection limits ( YD and XD). The obtained experimental values, for 5% probability of false positives and 5% probability of false negatives, were YC = 56.0 mV, YD = 125. mV, XC = 0.132 μg/mL and XD = 0.293 μg/mL. For 5% probability of false positives and 1% probability of false negatives, the obtained detection limits were YD = 158 . mV and XD = 0.371 μg/mL. Furthermore, by using bootstrapping methodology on the experimental data for the standards and the analytical blank, it was possible to validate previously published experimental domain expressions for the decision levels ( yC and xC) and detection limits ( yD and xD). This was demonstrated by testing the generated decision levels and detection limits for their performance in regard to false positives and false negatives. In every case, the obtained numbers of false negatives and false positives were as specified a priori.

Transfer effects of errorless Goal Management Training on cognitive function and quality of life in brain-injured persons.

PubMed

Bertens, Dirk; Kessels, Roy P C; Boelen, Danielle H E; Fasotti, Luciano

2016-01-01

Previous findings had shown that the addition of errorless learning to traditional Goal Management Training (GMT) resulted in superior results when training everyday tasks in persons with executive deficits after brain injury. To investigate the additional effects of an errorless GMT on cognitive function and quality of life after acquired brain injury. This is a supplementary analysis of findings from an RCT in which 67 patients with executive impairments after acquired brain injury were randomly allocated to an experimental errorless GMT (n = 33) or conventional GMT (n = 34) to train two individually chosen everyday tasks. Objective cognitive function using neuropsychological tests, subjective cognitive complaints and quality of life using questionnaires were assessed before and after training. No significant interaction effects between these three types of outcome measures and the two forms of GMT were found. Irrespective of treatment, performance on two executive tests (Modified Six Elements Test; p = 0.006, Zoo Map test; p = 0.001) improved and daily executive function problems as reported by the participants (EFI; p = 0.001) and proxies (DEX; p = 0.01) diminished. Besides the previously found superiority of errorless GMT when training everyday tasks, additional improvements in cognition and quality of life did not differ between the two treatments.

Deformed Shape Calculation of a Full-Scale Wing Using Fiber Optic Strain Data from a Ground Loads Test

NASA Technical Reports Server (NTRS)

Jutte, Christine V.; Ko, William L.; Stephens, Craig A.; Bakalyar, John A.; Richards, W. Lance

2011-01-01

A ground loads test of a full-scale wing (175-ft span) was conducted using a fiber optic strain-sensing system to obtain distributed surface strain data. These data were input into previously developed deformed shape equations to calculate the wing s bending and twist deformation. A photogrammetry system measured actual shape deformation. The wing deflections reached 100 percent of the positive design limit load (equivalent to 3 g) and 97 percent of the negative design limit load (equivalent to -1 g). The calculated wing bending results were in excellent agreement with the actual bending; tip deflections were within +/- 2.7 in. (out of 155-in. max deflection) for 91 percent of the load steps. Experimental testing revealed valuable opportunities for improving the deformed shape equations robustness to real world (not perfect) strain data, which previous analytical testing did not detect. These improvements, which include filtering methods developed in this work, minimize errors due to numerical anomalies discovered in the remaining 9 percent of the load steps. As a result, all load steps attained +/- 2.7 in. accuracy. Wing twist results were very sensitive to errors in bending and require further development. A sensitivity analysis and recommendations for fiber implementation practices, along with, effective filtering methods are included

Examination of the pest status of corn-infesting Ulidiidae (Diptera).

PubMed

Goyal, Gaurav; Nuessly, Gregg S; Seal, Dakshina R; Steck, Gary J; Capinera, John L; Meagher, Robert L

2012-10-01

Larvae of 11 species of picture-winged flies (Diptera: Ulididae) are known to feed on corn plants (Zea mays L.) in the western hemisphere. Larvae emerge from eggs deposited in leaf axils and corn silk to feed mostly within ears, but the primary versus secondary nature (i.e., pest status) of their infestation is not known for all of these species. Choice and no-choice tests by using a split-plot design were conducted in greenhouse and field trials to determine the pest status on sweet corn of three of these species found in Florida: Chaetopsis massyla (Walker), Euxesta eluta Loew, and E. stigmatias Loew. The main treatments (uninfested ears and ears experimentally infested with either Spodoptera frugiperda [Lepidoptera: Noctuidae] or E. eluta larvae) were applied at first silk. The subtreatments (C. massyla, E. eluta, or E. stigmatias adults caged on ears) were applied 7 d later and maintained for 10 d. All three fly species were reared from uninfested and experimentally infested ears in both choice and no-choice tests in greenhouse and field trials confirming both primary and secondary modes of ear infestation. More flies of all three species emerged from ears that were preinfested with S. frugiperda compared with uninfested ears suggesting either preference for or greater survival within ears previously infested by S. frugiperda. Fewer E. eluta and E. stigmatias emerged from ears preinfested with E. eluta in no-choice field tests, suggesting that previous infestation by this fly may negatively affect oviposition or that older fly larvae affect survival of neonate larvae. All three species studied here should be considered primary pests that can render unprotected sweet corn ears unmarketable.

Effects of d-amphetamine, diazepam and buspirone on schedule-induced polydipsia suppressed by response-dependent and response-independent shock.

PubMed

Flores, P; Pellón, R

1998-03-01

Food deprived Wistar rats were exposed to a fixed time 60 s food schedule until they developed schedule-induced polydipsia. Rats were matched in pairs according to their licking rate, being designated experimental or yoked control at random. Every fifth lick by experimental rats was then followed by an electric shock (0.05, 0.1, or 0.2 mA) while the food schedule continued in operation. Yoked-control rats received the same shocks as experimental rats, but independently of their own licking. Drugs were then tested on the suppressed rates of licking. Diazepam (0.5-2.0 mg/kg) increased punished schedule-induced polydipsia, a result not observed in yoked controls. No increases in the licks per minute of experimental or control animals were found after d-amphetamine (0.25-4.0 mg/kg) or buspirone (0.5-8.0 mg/kg). In comparison with previous results it is concluded that the antipunishment effects of drugs on schedule-induced behaviour depend on the type of punishment contingency.

Understanding the Effect of Grain Boundary Character on Dynamic Recrystallization in Stainless Steel 316L

NASA Astrophysics Data System (ADS)

Beck, Megan; Morse, Michael; Corolewski, Caleb; Fritchman, Koyuki; Stifter, Chris; Poole, Callum; Hurley, Michael; Frary, Megan

2017-08-01

Dynamic recrystallization (DRX) occurs during high-temperature deformation in metals and alloys with low to medium stacking fault energies. Previous simulations and experimental research have shown the effect of temperature and grain size on DRX behavior, but not the effect of the grain boundary character distribution. To investigate the effects of the distribution of grain boundary types, experimental testing was performed on stainless steel 316L specimens with different initial special boundary fractions (SBF). This work was completed in conjunction with computer simulations that used a modified Monte Carlo method which allowed for the addition of anisotropic grain boundary energies using orientation data from electron backscatter diffraction (EBSD). The correlation of the experimental and simulation work allows for a better understanding of how the input parameters in the simulations correspond to what occurs experimentally. Results from both simulations and experiments showed that a higher fraction of so-called "special" boundaries ( e.g., Σ3 twin boundaries) delayed the onset of recrystallization to larger strains and that it is energetically favorable for nuclei to form on triple junctions without these so-called "special" boundaries.

The Effects of Blade Count on Boundary Layer Development in a Low-Pressure Turbine

NASA Technical Reports Server (NTRS)

Dorney, Daniel J.; Flitan, Horia C.; Ashpis, David E.; Solomon, William J.

2000-01-01

Experimental data from jet-engine tests have indicated that turbine efficiencies at takeoff can be as much as two points higher than those at cruise conditions. Recent studies have shown that Reynolds number effects contribute to the lower efficiencies at cruise conditions. In the current study numerical simulations have been performed to study the boundary layer development in a two-stage low-pressure turbine, and to evaluate the models available for low Reynolds number flows in turbomachinery. In a previous study using the same geometry the predicted time-averaged boundary layer quantities showed excellent agreement with the experimental data, but the predicted unsteady results showed only fair agreement with the experimental data. It was surmised that the blade count approximation used in the numerical simulations generated more unsteadiness than was observed in the experiments. In this study a more accurate blade approximation has been used to model the turbine, and the method of post-processing the boundary layer information has been modified to more closely resemble the process used in the experiments. The predicted results show improved agreement with the unsteady experimental data.

Systematic Validation of Protein Force Fields against Experimental Data

PubMed Central

Eastwood, Michael P.; Dror, Ron O.; Shaw, David E.

2012-01-01

Molecular dynamics simulations provide a vehicle for capturing the structures, motions, and interactions of biological macromolecules in full atomic detail. The accuracy of such simulations, however, is critically dependent on the force field—the mathematical model used to approximate the atomic-level forces acting on the simulated molecular system. Here we present a systematic and extensive evaluation of eight different protein force fields based on comparisons of experimental data with molecular dynamics simulations that reach a previously inaccessible timescale. First, through extensive comparisons with experimental NMR data, we examined the force fields' abilities to describe the structure and fluctuations of folded proteins. Second, we quantified potential biases towards different secondary structure types by comparing experimental and simulation data for small peptides that preferentially populate either helical or sheet-like structures. Third, we tested the force fields' abilities to fold two small proteins—one α-helical, the other with β-sheet structure. The results suggest that force fields have improved over time, and that the most recent versions, while not perfect, provide an accurate description of many structural and dynamical properties of proteins. PMID:22384157

Analysis of concrete targets with different kinds of reinforcements subjected to blast loading

NASA Astrophysics Data System (ADS)

Oña, M.; Morales-Alonso, G.; Gálvez, F.; Sánchez-Gálvez, V.; Cendón, D.

2016-05-01

In this paper we describe an experimental campaign carried out to study and analyse the behaviour of concrete slabs when subjected to blast loading. Four different types of concrete have been tested: normal strength concrete with steel rebar, normal strength concrete with steel rebar retrofitted with Kevlar coating, steel fibre reinforced concrete (SFRC) and polypropylene fibre reinforced concrete (PFRC). The major asset of the experimental setup used is that it allows to subject up to four specimens to the same blast load what, besides being cost effective, makes possible to have a measure of the experimental scatter. The results of SFRC and PFRC concretes have been analysed by using a previously developed material model for the numerical simulation of concrete elements subjected to blast. The experimental campaign and preliminary results of this numerical analysis show how the high strain rates, in spite of improving the mechanical properties of these kinds of fibre reinforced concretes, lead to an embrittlement of the material, which may be dangerous from the point of view of the structural behaviour.

Differential Expression of Ethanol-Induced Hypothermia in Adolescent and Adult Rats Induced by Pretest Familiarization to the Handling/Injection Procedure

PubMed Central

Ristuccia, Robert C.; Hernandez, Michael; Wilmouth, Carrie E.; Spear, Linda P.

2007-01-01

Background Previous work examining ethanol’s autonomic effects has found contrasting patterns of age-related differences in ethanol-induced hypothermia between adolescent and adult rats. Most studies have found adolescents to be less sensitive than adults to this effect, although other work has indicated that adolescents may be more sensitive than adults under certain testing conditions. To test the hypothesis that adolescents show more ethanol hypothermia than adults when the amount of disruption induced by the test procedures is low, but less hypothermia when the experimental perturbation is greater, the present study examined the consequences of manipulating the amount of perturbation at the time of testing on ethanol-induced hypothermia in adolescent and adult rats. Methods The amount of test disruption was manipulated by administering ethanol through a chronically indwelling gastric cannula (low perturbation) versus via intragastric intubation (higher perturbation) in Experiment 1 or by either familiarizing animals to the handling and injection procedure for several days pretest or leaving them unmanipulated before testing in Experiment 2. Results The results showed that the handling manipulation, but not the use of gastric cannulae, altered the expression of ethanol-induced hypothermia differentially across age. When using a familiarization protocol sufficient to reduce the corticosterone response to the handling and injection procedure associated with testing, adolescents showed greater hypothermia than adults. In contrast, the opposite pattern of age differences in hypothermia was evident in animals that were not manipulated before the test day. Surprisingly, however, this difference across testing circumstances was driven by a marked reduction in hypothermia among adults who had been handled before testing, with handling having relatively little impact on ethanol hypothermia among adolescents. Conclusions Observed differences between adolescents and adults in the autonomic consequences of ethanol were dramatically influenced by whether animals were familiarized with the handling/injection process before testing. Under these circumstances, adolescents were less susceptible than adults to the impact of experimental perturbation on ethanol-induced hypothermia. These findings suggest that seemingly innocuous aspects of experimental design can influence conclusions reached on ontogenetic differences in sensitivity to ethanol, at least when indexed by ethanol-induced hypothermia. PMID:17374036

Differential expression of ethanol-induced hypothermia in adolescent and adult rats induced by pretest familiarization to the handling/injection procedure.

PubMed

Ristuccia, Robert C; Hernandez, Michael; Wilmouth, Carrie E; Spear, Linda P

2007-04-01

Previous work examining ethanol's autonomic effects has found contrasting patterns of age-related differences in ethanol-induced hypothermia between adolescent and adult rats. Most studies have found adolescents to be less sensitive than adults to this effect, although other work has indicated that adolescents may be more sensitive than adults under certain testing conditions. To test the hypothesis that adolescents show more ethanol hypothermia than adults when the amount of disruption induced by the test procedures is low, but less hypothermia when the experimental perturbation is greater, the present study examined the consequences of manipulating the amount of perturbation at the time of testing on ethanol-induced hypothermia in adolescent and adult rats. The amount of test disruption was manipulated by administering ethanol through a chronically indwelling gastric cannula (low perturbation) versus via intragastric intubation (higher perturbation) in Experiment 1 or by either familiarizing animals to the handling and injection procedure for several days pretest or leaving them unmanipulated before testing in Experiment 2. The results showed that the handling manipulation, but not the use of gastric cannulae, altered the expression of ethanol-induced hypothermia differentially across age. When using a familiarization protocol sufficient to reduce the corticosterone response to the handling and injection procedure associated with testing, adolescents showed greater hypothermia than adults. In contrast, the opposite pattern of age differences in hypothermia was evident in animals that were not manipulated before the test day. Surprisingly, however, this difference across testing circumstances was driven by a marked reduction in hypothermia among adults who had been handled before testing, with handling having relatively little impact on ethanol hypothermia among adolescents. Observed differences between adolescents and adults in the autonomic consequences of ethanol were dramatically influenced by whether animals were familiarized with the handling/injection process before testing. Under these circumstances, adolescents were less susceptible than adults to the impact of experimental perturbation on ethanol-induced hypothermia. These findings suggest that seemingly innocuous aspects of experimental design can influence conclusions reached on ontogenetic differences in sensitivity to ethanol, at least when indexed by ethanol-induced hypothermia.

Experimental model with bilioenteric anastomosis in rats--technique and significance.

PubMed

Nagai, T; Yamakawa, T

1992-08-01

A simple technique of hepaticojejunostomy in rats is introduced in this paper and its suitability for use as an experimental model was evaluated histologically. Hepaticojejunostomy was performed as follows; the stump of the supra-pancreatic common bile duct (CBD), detached from adjacent tissue, was introduced into the jejunal lumen using the outer catheter previously inserted into the jejunum, and the jejunal wall close to the implantation site of the CBD was fixed to the porta hepatitis with a suture. Among 40 rats in which hepaticojejunostomy was performed, the postoperative mortality rate was 17.5%. The remaining experimental animals (33 rats, 82.5%) survived for the duration of this study. The rats were sacrificed at 3, 5, 8, and 12 months after surgery, and liver function tests, macroscopic and histological studies of the biliary tract were carried out. No signs of cholangitis or liver abscess were noted in any experimental animals during this period. The median values of liver function tests were within normal limits in almost all of the experimental rats. The anastomotic stoma was also patent, and free drainage of bile was noted, but the bile duct proximal to the site of anastomosis was generally macroscopically dilated. Histologically, epithelial hyperplasia and fibrous thickening of the wall accompanied by inflammatory cell infiltration were noted in the rats sacrificed at 3 and 5 months postoperatively. Marked hyperplasia of mucous glands, goblet cell metaplasia and atypical epithelium were usually seen in the rats killed at 8 months and 12 months after surgery.(ABSTRACT TRUNCATED AT 250 WORDS)

Injury tolerance of tibia for the car-pedestrian impact.

PubMed

Mo, Fuhao; Arnoux, Pierre Jean; Jure, Jean Jaques; Masson, Catherine

2012-05-01

Lower limbs are normally the first contacted body region during car-pedestrian accidents, and easily suffer serious injuries. The previous tibia bending tolerances for pedestrian safety were mainly developed from three-point bending tests on tibia mid-shaft. The tibia tolerances of other locations are still not investigated enough. In addition, tibia loading condition under the car-pedestrian impact should be explored to compare with the three-point bending. This work aims to investigate the injury tolerance of tibia fracture with combined experimental data and numerical simulation. Eleven new reported quasi-static bending tests of tibia mid-shaft, and additional eleven dynamic mid-shaft bending test results in the previous literature were used to define injury risk functions. Furthermore, to investigate the influence of tibia locations on bending tolerance, finite element simulations with lower limb model were implemented according to three-point bending and pedestrian impact conditions. The regressive curve of tibia bending tolerance was obtained from the simulations on the different impact locations, and indicated that tibia fracture tolerance could vary largely due to the impact locations for the car-pedestrian crash. Copyright © 2011 Elsevier Ltd. All rights reserved.

On-road and wind-tunnel measurement of motorcycle helmet noise.

PubMed

Kennedy, J; Carley, M; Walker, I; Holt, N

2013-09-01

The noise source mechanisms involved in motorcycling include various aerodynamic sources and engine noise. The problem of noise source identification requires extensive data acquisition of a type and level that have not previously been applied. Data acquisition on track and on road are problematic due to rider safety constraints and the portability of appropriate instrumentation. One way to address this problem is the use of data from wind tunnel tests. The validity of these measurements for noise source identification must first be demonstrated. In order to achieve this extensive wind tunnel tests have been conducted and compared with the results from on-track measurements. Sound pressure levels as a function of speed were compared between on track and wind tunnel tests and were found to be comparable. Spectral conditioning techniques were applied to separate engine and wind tunnel noise from aerodynamic noise and showed that the aerodynamic components were equivalent in both cases. The spectral conditioning of on-track data showed that the contribution of engine noise to the overall noise is a function of speed and is more significant than had previously been thought. These procedures form a basis for accurate experimental measurements of motorcycle noise.

Optics-Only Calibration of a Neural-Net Based Optical NDE Method for Structural Health Monitoring

NASA Technical Reports Server (NTRS)

Decker, Arthur J.

2004-01-01

A calibration process is presented that uses optical measurements alone to calibrate a neural-net based NDE method. The method itself detects small changes in the vibration mode shapes of structures. The optics-only calibration process confirms previous work that the sensitivity to vibration-amplitude changes can be as small as 10 nanometers. A more practical value in an NDE service laboratory is shown to be 50 nanometers. Both model-generated and experimental calibrations are demonstrated using two implementations of the calibration technique. The implementations are based on previously published demonstrations of the NDE method and an alternative calibration procedure that depends on comparing neural-net and point sensor measurements. The optics-only calibration method, unlike the alternative method, does not require modifications of the structure being tested or the creation of calibration objects. The calibration process can be used to test improvements in the NDE process and to develop a vibration-mode-independence of damagedetection sensitivity. The calibration effort was intended to support NASA s objective to promote safety in the operations of ground test facilities or aviation safety, in general, by allowing the detection of the gradual onset of structural changes and damage.

KSC-02pd0032

NASA Image and Video Library

2002-01-17

KENNEDY SPACE CENTER, FLA. -- In the Vertical Processing Facility, workers help guide the Near Infrared Camera and Multi-Object Spectrometer (NICMOS) Cooling System into an protective enclosure on a payload carrier. NICMOS II is part of the payload on mission STS-109, the Hubble Servicing Telescope Mission. It is a new experimental cooling system consisting of a compressor and tiny turbines. With the experimental cryogenic system, NASA hopes to re-cool the infrared detectors to below -315 degrees F (-193 degrees Celsius). NICMOS II was previously tested aboard STS-95 in 1998. It could extend the life of the Hubble Space Telescope by several years. Astronauts aboard Columbia on mission STS-109 will be replacing the original NICMOS with the newer version. Launch of mission STS-109 is scheduled for Feb. 28, 2002

Investigation of the Temperature Hysteresis Phenomenon of a Loop Heat Pipe

NASA Technical Reports Server (NTRS)

Kaya, Tarik; Ku, Jentung; Hoang, Triem; Cheung, Mark K.

1999-01-01

The temperature hysteresis phenomenon of a Loop Heat Pipe (LHP) was experimentally investigated. The temperature hysteresis was identified by the fact that the operating temperature depends upon not only the imposed power but also the previous history of the power variation. The temperature hysteresis could impose limitations on the LHP applications since the LHP may exhibit different steady-state operating temperatures at a given power input even when the condenser sink temperature remains unchanged. In order to obtain insight to this phenomenon, a LHP was tested at different elevations and tilts by using an elaborated power profile. A hypothesis was suggested to explain the temperature hysteresis. This hypothesis explains well the experimental observations. Results of this study provide a better understanding of the performance characteristics of the LHPS.

Laminar Heat-Transfer and Pressure-Distribution Studies on a Series of Reentry Nose Shapes at a Mach Number of 19.4 in Helium

NASA Technical Reports Server (NTRS)

Wagner, Richard D., Jr.; Pine, W. Clint; Henderson, Arthur, Jr.

1961-01-01

An experimental investigation has been conducted in the 2-inch helium tunnel at the Langley Research Center at a Mach number of 19.4 to determine the pressure distributions and heat-transfer characteristics of a family of reentry nose shapes. The pressure and heat-transfer-rate distributions on the nose shapes are compared with theoretical predictions to ascertain the limitations and validity of the theories at hypersonic speeds. The experimental results were found to be adequately predicted by existing theories. Two of the nose shapes were tested with variable-length flow-separation spikes. The results obtained by previous investigators of spike-nose bodies were found to prevail at the higher Mach number of the present investigation.

Large area sheet task: Advanced dendritic web growth development

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.; Meier, D.; Schruben, J.

1981-01-01

The growth of silicon dendritic web for photovoltaic applications was investigated. The application of a thermal model for calculating buckling stresses as a function of temperature profile in the web is discussed. Lid and shield concepts were evaluated to provide the data base for enhancing growth velocity. An experimental web growth machine which embodies in one unit the mechanical and electronic features developed in previous work was developed. In addition, evaluation of a melt level control system was begun, along with preliminary tests of an elongated crucible design. The economic analysis was also updated to incorporate some minor cost changes. The initial applications of the thermal model to a specific configuration gave results consistent with experimental observation in terms of the initiation of buckling vs. width for a given crystal thickness.

Experimental study of cryogen spray properties for application in dermatologic laser surgery.

PubMed

Aguilar, Guillermo; Majaron, Boris; Karapetian, Emil; Lavernia, Enrique J; Nelson, J Stuart

2003-07-01

Cryogenic sprays are used for cooling human skin during laser dermatologic surgery. In this paper, six straight-tube nozzles are characterized by photographs of cryogenic spray shapes, as well as measurements of average droplet diameter, velocity, and temperature. A single-droplet evaporation model to predict average spray droplet diameter and temperature is tested using the experimental data presented here. The results show two distinct spray patterns--sprays for 1.4-mm-diameter nozzles (wide nozzles) show significantly larger average droplet diameters and higher temperatures as a function of distance from the nozzle compared with those for 0.5-0.8-mm-diameter nozzles (narrow nozzles). These results complement and support previously reported studies, indicating that wide nozzles induce more efficient heat extraction than the narrow nozzles.

The transfer of Crel contextual control (same, opposite, less than, more than) through equivalence relations.

PubMed

Perez, William F; Kovac, Roberta; Nico, Yara C; Caro, Daniel M; Fidalgo, Adriana P; Linares, Ila; de Almeida, João Henrique; de Rose, Júlio C

2017-11-01

According to Relational Frame Theory (RFT) C rel denotes a contextual stimulus that controls a particular type of relational response (sameness, opposition, comparative, temporal, hierarchical etc.) in a given situation. Previous studies suggest that contextual functions may be indirectly acquired via transfer of function. The present study investigated the transfer of C rel contextual control through equivalence relations. Experiment 1 evaluated the transfer of C rel contextual functions for relational responses based on sameness and opposition. Experiment 2 extended these findings by evaluating transfer of function using comparative C rel stimuli. Both experiments followed a similar sequence of phases. First, abstract forms were established as C rel stimuli via multiple exemplar training (Phase 1). The contextual cues were then applied to establish arbitrary relations among nonsense words and to test derived relations (Phase 2). After that, equivalence relations involving the original C rel stimuli and other abstract forms were trained and tested (Phase 3). Transfer of function was evaluated by replacing the directly established C rel stimuli with their equivalent stimuli in the former experimental tasks (Phases 1 and 2). Results from both experiments suggest that C rel contextual control may be extended via equivalence relations, allowing other arbitrarily related stimuli to indirectly acquire C rel functions and regulate behavior by evoking appropriate relational responses in the presence of both previously known and novel stimuli. © 2017 Society for the Experimental Analysis of Behavior.

Capuchins, space, time and memory: an experimental test of what-where-when memory in wild monkeys

PubMed Central

2016-01-01

There is considerable controversy about the existence, extent and adaptive value of integrated multimodal memory in non-human animals. Building on prior results showing that wild capuchin monkeys in Argentina appear to recall both the location and amount of food at patches they had previously visited, I tested whether they also track and use elapsed time as a basis for decisions about which feeding patches to visit. I presented them with an experimental array of eight feeding sites, at each of which food rewards increased with increasing elapsed time since the previous visit, similar to the pattern of ripe fruit accumulation in natural feeding trees. Over the course of 68 days, comprising two distinct renewal rate treatments, one group repeatedly visited sites in the feeding array, generating 212 valid choices between sites. Comparison of observations against simulated movements and multinomial statistical models shows that the monkeys' choices were most consistent with dynamic memory for elapsed time specific to each of the eight sites. Thus, it appears that capuchin monkeys possess and use integrated memories of prior food patch use, including where the patch is relative to their current location, how productive the patch is and how long it has been since they last visited the patch. Natural selection to use such integrated memories in foraging tasks may provide an ecologically relevant basis for the evolution of complex intelligence in primates. PMID:27708145

Laboratory-Scale Column Testing Using IONSIV IE-911 for Removing Cesium from Acidic Tank Waste Simulant. 2: Determination of Cesium Exchange Capacity and Effective Mass Transfer Coefficient from a 500-cm3 Column Experiement

DOE Office of Scientific and Technical Information (OSTI.GOV)

T.J. Tranter; R.D. Tillotson; T.A. Todd

2005-04-01

A semi-scale column test was performed using a commercial form of crystalline silicotitanate (CST) for removing radio-cesium from a surrogate acidic tank solution, which represents liquid waste stored at the Idaho National Engineering and Environmental Laboratory (INEEL). The engineered form of CST ion exchanger, known as IONSIVtmIE-911 (UOP, Mt. Laurel,NJ, USA), was tested in a 500-cm3 column to obtain a cesium breakthrough curve. The cesium exchange capacity of this column matched that obtained from previous testing with a 15-mc3 column. A numerical algorithm using implicit finite difference approximations was developed to solve the governing mass transport equations for the CSTmore » columns. An effective mass transfer coefficient was derived from solving these equations for previously reported 15 cm3 tests. The effective mass transfer coefficient was then used to predict the cesium breakthrough curve for the 500-cm3 column and compared to the experimental data reported in this paper. The calculated breakthrough curve showed excellent agreement with the data from the 500-cm3 column even though the interstitial velocity was a factor of two greater. Thus, this approach should provide a reasonable method for scale up to larger columns for treating actual tank waste.« less

Impact of Jigsaw on the Achievement and Attitudes of Saudi Arabian Male High School Science Students

NASA Astrophysics Data System (ADS)

Alghamdi, Abdulmonem

The aim of the study is to investigate the impact of cooperative learning instruction, specifically by using the Jigsaw instructional strategy on science achievement and attitudes towards science among 11th grade students. Based upon previous research literature, it was hypothesized that significant differences existed on gains between general science achievement of experimental group and control group. The quasi-experimental design was chosen for this study. The study sample consisted of 50 students of 11th grade class who were equally distributed among experimental group and control group, matched on the basic of their annual examination at general science scores. The students' achievement was measured through the implementation of 30-item achievement test used as a pretest, as well as a posttest and deferred (follow-up) test. The experiment group was taught through cooperative learning while control group was taught through the instructions of "traditional teaching". The material was used such as lesson plans, worksheets and quizzes, designed to implement Jigsaw as a cooperative learning methodology. For the attitude scale towards science, a published 30-item Likert scale called Test of Science Related Attitudes (TOSRA) has been translated to Arabic in order to determine the students' attitudes ranging between strongly agree to strongly disagree. The data were analyzed through repeated measure analysis and multivariate analysis of variance with a .05 selected level of significance. The results of this study showed that using Jigsaw as a cooperative learning strategy has improved the students' achievement for the benefit of the experimental group. However, there was no significant change on the students' attitudes towards science for both groups, where the scores of all the attitude subscales were at or near the neutral level.

A Theoretical Investigation of Composite Overwrapped Pressure Vessel (COPV) Mechanics Applied to NASA Full Scale Tests

NASA Technical Reports Server (NTRS)

Thesken, John C.; Murthy, Pappu L. N.; Phoenix, S. L.; Greene, N.; Palko, Joseph L.; Eldridge, Jeffrey; Sutter, James; Saulsberry, R.; Beeson, H.

2009-01-01

A theoretical investigation of the factors controlling the stress rupture life of the National Aeronautics and Space Administration's (NASA) composite overwrapped pressure vessels (COPVs) continues. Kevlar (DuPont) fiber overwrapped tanks are of particular concern due to their long usage and the poorly understood stress rupture process in Kevlar filaments. Existing long term data show that the rupture process is a function of stress, temperature and time. However due to the presence of a load sharing liner, the manufacturing induced residual stresses and the complex mechanical response, the state of actual fiber stress in flight hardware and test articles is not clearly known. This paper is a companion to a previously reported experimental investigation and develops a theoretical framework necessary to design full-scale pathfinder experiments and accurately interpret the experimentally observed deformation and failure mechanisms leading up to static burst in COPVs. The fundamental mechanical response of COPVs is described using linear elasticity and thin shell theory and discussed in comparison to existing experimental observations. These comparisons reveal discrepancies between physical data and the current analytical results and suggest that the vessel s residual stress state and the spatial stress distribution as a function of pressure may be completely different from predictions based upon existing linear elastic analyses. The 3D elasticity of transversely isotropic spherical shells demonstrates that an overly compliant transverse stiffness relative to membrane stiffness can account for some of this by shifting a thin shell problem well into the realm of thick shell response. The use of calibration procedures are demonstrated as calibrated thin shell model results and finite element results are shown to be in good agreement with the experimental results. The successes reported here have lead to continuing work with full scale testing of larger NASA COPV hardware.

Blade loss transient dynamics analysis, volume 2. Task 2: Theoretical and analytical development. Task 3: Experimental verification

NASA Technical Reports Server (NTRS)

Gallardo, V. C.; Storace, A. S.; Gaffney, E. F.; Bach, L. J.; Stallone, M. J.

1981-01-01

The component element method was used to develop a transient dynamic analysis computer program which is essentially based on modal synthesis combined with a central, finite difference, numerical integration scheme. The methodology leads to a modular or building-block technique that is amenable to computer programming. To verify the analytical method, turbine engine transient response analysis (TETRA), was applied to two blade-out test vehicles that had been previously instrumented and tested. Comparison of the time dependent test data with those predicted by TETRA led to recommendations for refinement or extension of the analytical method to improve its accuracy and overcome its shortcomings. The development of working equations, their discretization, numerical solution scheme, the modular concept of engine modelling, the program logical structure and some illustrated results are discussed. The blade-loss test vehicles (rig full engine), the type of measured data, and the engine structural model are described.

Advanced Shock Position Control for Mode Transition in a Turbine Based Combined Cycle Engine Inlet Model

NASA Technical Reports Server (NTRS)

Csank, Jeffrey T.; Stueber, Thomas J.

2013-01-01

A dual flow-path inlet system is being tested to evaluate methodologies for a Turbine Based Combined Cycle (TBCC) propulsion system to perform a controlled inlet mode transition. Prior to experimental testing, simulation models are used to test, debug, and validate potential control algorithms. One simulation package being used for testing is the High Mach Transient Engine Cycle Code simulation, known as HiTECC. This paper discusses the closed loop control system, which utilizes a shock location sensor to improve inlet performance and operability. Even though the shock location feedback has a coarse resolution, the feedback allows for a reduction in steady state error and, in some cases, better performance than with previous proposed pressure ratio based methods. This paper demonstrates the design and benefit with the implementation of a proportional-integral controller, an H-Infinity based controller, and a disturbance observer based controller.

Deposit formation in hydrocarbon rocket fuels with an evaluation of a propane heat transfer correlation

NASA Technical Reports Server (NTRS)

Masters, P. A.; Aukerman, C. A.

1982-01-01

A high pressure fuel coking testing apparatus was designed and developed and was used to evaluate thermal decomposition limits and carbon decomposition rates in heated copper tubes for hydrocarbon fuels. A commercial propane (90% grade) and chemically pure (CP) propane were tested. Heat transfer to supercritical propane was evaluated at 136 atm, bulk fluid velocities of 6 to 30 m/s, and tube wall temperatures in the range of 422 to 811 K. A forced convection heat transfer correlation developed in a previous test effort verified a prediction of most of the experimental data within a + or - 30% range, with good agreement for the CP propane data. No significant differences were apparent in the predictions derived from the correlation when the carbon resistance was included with the film resistance. A post-test scanning electron microprobe analysis indicated occurrences of migration and interdiffusion of copper into the carbon deposit.

Thermomechanical and bithermal fatigue behavior of cast B1900 + Hf and wrought Haynes 188

NASA Technical Reports Server (NTRS)

Halford, G. R.; Verrilli, M. J.; Kalluri, S.; Ritzert, F. J.; Duckert, R. E.; Holland, F. A.

1992-01-01

A thermomechanical fatigue (TMF) high-temperature life prediction method has been evaluated using the experimental data. Bithermal fatigue (BTF), bithermal creep-fatigue (BTC-F), and TMF experiments were performed using two aerospace structural alloys, cast B1900 + Hf and wrought Haynes 188. The method which is based on the total strain version of strain range partitioning and unified cyclic constitutive modeling requires, as an input, information on the flow and failure behavior of the material of interest. Bithermal temperatures of 483 and 871 C were used for the cast B1900 + Hf nickel-base alloy and 316 and 760 C for the wrought Haynes 188 cobalt-base alloy. Maximum and minimum temperatures were also used in both TMF and BTF tests. Comparisons were made between the results of these tests and isothermal tensile and fatigue test data obtained previously. Qualitative correlations were observed between tensile and isothermal fatigue tests.

Liquid Acquisition Device Testing with Sub-Cooled Liquid Oxygen

NASA Technical Reports Server (NTRS)

Jurns, John M.; McQuillen, John B.

2008-01-01

When transferring propellant in space, it is most efficient to transfer single phase liquid from a propellant tank to an engine. In earth s gravity field or under acceleration, propellant transfer is fairly simple. However, in low gravity, withdrawing single-phase fluid becomes a challenge. A variety of propellant management devices (PMD) are used to ensure single-phase flow. One type of PMD, a liquid acquisition device (LAD) takes advantage of capillary flow and surface tension to acquire liquid. Previous experimental test programs conducted at NASA have collected LAD data for a number of cryogenic fluids, including: liquid nitrogen (LN2), liquid oxygen (LOX), liquid hydrogen (LH2), and liquid methane (LCH4). The present work reports on additional testing with sub-cooled LOX as part of NASA s continuing cryogenic LAD development program. Test results extend the range of LOX fluid conditions examined, and provide insight into factors affecting predicting LAD bubble point pressures.

A Multi-Verse Optimizer with Levy Flights for Numerical Optimization and Its Application in Test Scheduling for Network-on-Chip.

PubMed

Hu, Cong; Li, Zhi; Zhou, Tian; Zhu, Aijun; Xu, Chuanpei

2016-01-01

We propose a new meta-heuristic algorithm named Levy flights multi-verse optimizer (LFMVO), which incorporates Levy flights into multi-verse optimizer (MVO) algorithm to solve numerical and engineering optimization problems. The Original MVO easily falls into stagnation when wormholes stochastically re-span a number of universes (solutions) around the best universe achieved over the course of iterations. Since Levy flights are superior in exploring unknown, large-scale search space, they are integrated into the previous best universe to force MVO out of stagnation. We test this method on three sets of 23 well-known benchmark test functions and an NP complete problem of test scheduling for Network-on-Chip (NoC). Experimental results prove that the proposed LFMVO is more competitive than its peers in both the quality of the resulting solutions and convergence speed.

A Multi-Verse Optimizer with Levy Flights for Numerical Optimization and Its Application in Test Scheduling for Network-on-Chip

PubMed Central

Hu, Cong; Li, Zhi; Zhou, Tian; Zhu, Aijun; Xu, Chuanpei

2016-01-01

We propose a new meta-heuristic algorithm named Levy flights multi-verse optimizer (LFMVO), which incorporates Levy flights into multi-verse optimizer (MVO) algorithm to solve numerical and engineering optimization problems. The Original MVO easily falls into stagnation when wormholes stochastically re-span a number of universes (solutions) around the best universe achieved over the course of iterations. Since Levy flights are superior in exploring unknown, large-scale search space, they are integrated into the previous best universe to force MVO out of stagnation. We test this method on three sets of 23 well-known benchmark test functions and an NP complete problem of test scheduling for Network-on-Chip (NoC). Experimental results prove that the proposed LFMVO is more competitive than its peers in both the quality of the resulting solutions and convergence speed. PMID:27926946

Dose titration of moxidectin oral gel against migrating Strongylus vulgaris and Parascaris equorum larvae in pony foals.

PubMed

Monahan, C M; Chapman, M R; Taylor, H W; French, D D; Klei, T R

1995-11-01

Moxidectin was tested for efficacy in ponies against experimental infections of 56 day Strongylus vulgaris larvae and 11 day Parascaris equorum larvae. Three dosages of moxidectin were tested: 300 micrograms per kg live body weight, 400 micrograms per kg, and 500 micrograms per kg, and the vehicle served as control. Ponies were first infected with 600 S. vulgaris third-stage larvae (L3) on Experiment Day 0 and then with 3000 embryonated P. equorum eggs on Day 45. Moxidectin treatments were administered on Day 56 and necropsy examinations were performed on Day 91. Strongylus vulgaris fourth-stage (L4) and fifth-stage (L5) larvae were recovered at necropsy from the control ponies, in dissections of the cranial mesenteric artery and its branches (L4 and L5), and recovered from nodules in the wall of the cecum and ventral colon (L5). Parascaris equorum larvae were recovered from the small intestine of control ponies. Moxidectin was highly efficacious against S. vulgaris L4 and L5 at all three doses tested (99.6-100%), and appeared to be equally efficacious against P. equorum larvae (100%); however, control ponies had low levels of P. equorum infections compared to previous experimental infections performed using identical methods. This suggests that the prior S. vulgaris infection on Day 0 may have influenced the subsequent experimental P. equorum infection on Day 45 and contributed to the lower recovery.

Experimental investigation of alternative transmission functions: Quantitative evidence for the importance of nonlinear transmission dynamics in host-parasite systems.

PubMed

Orlofske, Sarah A; Flaxman, Samuel M; Joseph, Maxwell B; Fenton, Andy; Melbourne, Brett A; Johnson, Pieter T J

2018-05-01

Understanding pathogen transmission is crucial for predicting and managing disease. Nonetheless, experimental comparisons of alternative functional forms of transmission remain rare, and those experiments that are conducted are often not designed to test the full range of possible forms. To differentiate among 10 candidate transmission functions, we used a novel experimental design in which we independently varied four factors-duration of exposure, numbers of parasites, numbers of hosts and parasite density-in laboratory infection experiments. We used interactions between amphibian hosts and trematode parasites as a model system and all candidate models incorporated parasite depletion. An additional manipulation involving anaesthesia addressed the effects of host behaviour on transmission form. Across all experiments, nonlinear transmission forms involving either a power law or a negative binomial function were the best-fitting models and consistently outperformed the linear density-dependent and density-independent functions. By testing previously published data for two other host-macroparasite systems, we also found support for the same nonlinear transmission forms. Although manipulations of parasite density are common in transmission studies, the comprehensive set of variables tested in our experiments revealed that variation in density alone was least likely to differentiate among competing transmission functions. Across host-pathogen systems, nonlinear functions may often more accurately represent transmission dynamics and thus provide more realistic predictions for infection. © 2017 The Authors. Journal of Animal Ecology published by John Wiley & Sons Ltd on behalf of British Ecological Society.

Enhanced performance of a novel anodic PdAu/VGCNF catalyst for electro-oxidation in a glycerol fuel cell.

PubMed

Yahya, N; Kamarudin, S K; Karim, N A; Masdar, M S; Loh, K S

2017-11-25

This study presents a novel anodic PdAu/VGCNF catalyst for electro-oxidation in a glycerol fuel cell. The reaction conditions are critical issues affecting the glycerol electro-oxidation performance. This study presents the effects of catalyst loading, temperature, and electrolyte concentration. The glycerol oxidation performance of the PdAu/VGCNF catalyst on the anode side is tested via cyclic voltammetry with a 3 mm 2 active area. The morphology and physical properties of the catalyst are examined using X-ray diffraction (XRD), field emission scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy. Then, optimization is carried out using the response surface method with central composite experimental design. The current density is experimentally obtained as a response variable from a set of experimental laboratory tests. The catalyst loading, temperature, and NaOH concentration are taken as independent parameters, which were evaluated previously in the screening experiments. The highest current density of 158.34 mAcm -2 is obtained under the optimal conditions of 3.0 M NaOH concentration, 60 °C temperature and 12 wt.% catalyst loading. These results prove that PdAu-VGCNF is a potential anodic catalyst for glycerol fuel cells.

Improved nonhuman animal welfare is related more to income equality than it is to income.

PubMed

Morris, Michael C

2013-01-01

The link between nonhuman animal welfare, income, and income inequality (Gini coefficient) was tested using consumption of animal products, laws protecting animals on the farm from the worst abuses, and animals used in experimentation as indicators. Experimentation on all animals and on rodents significantly increased in high-income European countries, although there was some evidence that the increase in experimentation on cats and dogs started to flatten out for the highest income countries. Consumption of all flesh products in high-income countries declined in more equal societies. More equal high-income countries also had stricter regulations protecting animals, although the same correlation was not seen between U.S. states. In New Zealand, there was some evidence that testing on cats and dogs declined during years when equality was improving. The results provide little evidence for a Kuznets effect of income on animal welfare, with the possible exception of companion animal treatment. They do, however, suggest that greater equality can be a predictor for better treatment of animals. Previous research has strongly suggested that social conditions for humans improve with greater equality. The same may be true for nonhuman animals. Alternatively, conditions conducive to improving human income equality may also lead to better animal welfare outcomes.

Determination of the core temperature of a Li-ion cell during thermal runaway

NASA Astrophysics Data System (ADS)

Parhizi, M.; Ahmed, M. B.; Jain, A.

2017-12-01

Safety and performance of Li-ion cells is severely affected by thermal runaway where exothermic processes within the cell cause uncontrolled temperature rise, eventually leading to catastrophic failure. Most past experimental papers on thermal runaway only report surface temperature measurement, while the core temperature of the cell remains largely unknown. This paper presents an experimentally validated method based on thermal conduction analysis to determine the core temperature of a Li-ion cell during thermal runaway using surface temperature and chemical kinetics data. Experiments conducted on a thermal test cell show that core temperature computed using this method is in good agreement with independent thermocouple-based measurements in a wide range of experimental conditions. The validated method is used to predict core temperature as a function of time for several previously reported thermal runaway tests. In each case, the predicted peak core temperature is found to be several hundreds of degrees Celsius higher than the measured surface temperature. This shows that surface temperature alone is not sufficient for thermally characterizing the cell during thermal runaway. Besides providing key insights into the fundamental nature of thermal runaway, the ability to determine the core temperature shown here may lead to practical tools for characterizing and mitigating thermal runaway.

Active learning of geometrical optics in high school: the ALOP approach

NASA Astrophysics Data System (ADS)

Alborch, Alejandra; Pandiella, Susana; Benegas, Julio

2017-09-01

A group comparison experiment of two high school classes with pre and post instruction testing has been carried out to study the suitability and advantages of using the active learning of optics and photonics (ALOP) curricula in high schools of developing countries. Two parallel, mixed gender, 12th grade classes of a high school run by the local university were chosen. One course was randomly selected to follow the experimental instruction, based on teacher and student activities contained in the ALOP Manual. The other course followed the traditional, teacher-centered, instruction previously practiced. Conceptual knowledge of the characteristics of image formation by plane mirrors and single convergent and divergent lenses was measured by applying, in both courses, the multiple-choice test, light and optics conceptual evaluation (LOCE). Measurement before instruction showed that initial knowledge was almost null, and therefore equivalent, in both courses. After instruction testing showed that the conceptual knowledge of students following the ALOP curricula more than doubled that achieved by students in the control course, a situation maintained throughout the six conceptual dimensions tested by the 34 questions of the LOCE test used in this experiment. Using a 60% performance level on the LOCE test as the threshold of satisfactory performance, most (about 90%) of the experimental group achieved this level—independent of initial knowledge, while no student following traditional instruction reached this level of understanding. Some considerations and recommendations for prospective users are also included.

Final Report for the Testing of the Y-12 Criticality Accident Alarm System Detectors at the Godiva IV Burst Reactor (IER-443)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scorby, John C.; Hickman, David; Hudson, Becka

This report documents the experimental conditions and final results for the performance testing of the Y-12 Criticality Accident Alarm System (CAAS) detectors at the Godiva IV Burst Reactor at the National Criticality Experimental Research Center (NCERC) at the Nevada National Security Site (NNSS). The testing followed a previously issued test plan and was conducted during the week of July 17, 2017, with completion on Thursday July 20. The test subjected CAAS detectors supplied by Y-12 to very intense and short duration mixed neutron and gamma radiation fields to establish compliance to maximum radiation and minimum pulse width requirements. ANSI/ANS- 8.3.1997more » states that the “system shall be sufficiently robust as to actuate an alarm signal when exposed to the maximum radiation expected”, which has been defined at Y-12, in Documented Safety Analyses (DSAs), to be a dose rate of 10 Rad/s. ANSI/ANS-8.3.1997 further states that “alarm actuation shall occur as a result of a minimum duration transient” which may be assumed to be 1 msec. The pulse widths and dose rates provided by each burst during the test exceeded those requirements. The CAAS detectors all provided an immediate alarm signal and remained operable after the bursts establishing compliance to the requirements and fitness for re-deployment at Y-12.« less

Slug Flow Analysis in Vertical Large Diameter Pipes

NASA Astrophysics Data System (ADS)

Roullier, David

The existence of slug flow in vertical co-current two-phase flow is studied experimentally and theoretically. The existence of slug flow in vertical direction implies the presence of Taylor bubbles separated by hydraulically sealed liquid slugs. Previous experimental studies such as Ombere-Ayari and Azzopardi (2007) showed the evidence of the non-existence of Taylor bubbles for extensive experimental conditions. Models developed to predict experimental behavior [Kocamustafaogullari et al. (1984), Jayanti and Hewitt. (1990) and Kjoolas et al. (2017)] suggest that Taylor bubbles may disappear at large diameters and high velocities. A 73-ft tall and 101.6-mm internal diameter test facility was used to conduct the experiments allowing holdup and pressure drop measurements at large L/D. Superficial liquid and gas velocities varied from 0.05-m/s to 0.2 m/s and 0.07 m/s to 7.5 m/s, respectively. Test section pressure varied from 38 psia to 84 psia. Gas compressibility effect was greatly reduced at 84 psia. The experimental program allowed to observe the flow patterns for flowing conditions near critical conditions predicted by previous models (air-water, 1016 mm ID, low mixture velocities). Flow patterns were observed in detail using wire-mesh sensor measurements. Slug-flow was observed for a narrow range of experimental conditions at low velocities. Churn-slug and churn-annular flows were observed for most of the experimental data-points. Cap-bubble flow was observed instead of bubbly flow at low vSg. Wire-mesh measurements showed that the liquid has a tendency to remain near to the walls. The standard deviation of radial holdup profile correlates to the flow pattern observed. For churn-slug flow, the profile is convex with a single maximum near the pipe center while it exhibits a concave shape with two symmetric maxima close to the wall for churn-annular flow. The translational velocity was measured by two consecutive wire-mesh sensor crosscorrelation. The results show linear trends at low mixture velocities and non-linear behaviors at high mixture velocities. The translational velocity trends seem to be related to the flow-pattern observed, namely to the ability of the gas to flow through the liquid structures. A simplified Taylor bubble stability model is proposed. The model allows to estimate under which conditions Taylor bubbles disappear, properly accounting for the diameter effect and velocity effect observed experimentally. In addition, annular flow distribution coefficient relating true holdup to centerline holdup in vertical flow is proposed. The proposed coefficient defines the tendency of the liquid to remain near the walls. This coefficient increases linearly with the void fraction.

Survival of bighorn sheep (Ovis canadensis) commingled with domestic sheep (Ovis aries) in the absence of Mycoplasma ovipneumoniae.

PubMed

Besser, Thomas E; Cassirer, E Frances; Yamada, Catherine; Potter, Kathleen A; Herndon, Caroline; Foreyt, William J; Knowles, Donald P; Srikumaran, Subramaniam

2012-01-01

To test the hypothesis that Mycoplasma ovipneumoniae is an important agent of the bighorn sheep (Ovis canadensis) pneumonia that has previously inevitably followed experimental commingling with domestic sheep (Ovis aries), we commingled M. ovipneumoniae-free domestic and bighorn sheep (n=4 each). One bighorn sheep died with acute pneumonia 90 days after commingling, but the other three remained healthy for >100 days. This unprecedented survival rate is significantly different (P=0.002) from that of previous bighorn-domestic sheep contact studies but similar to (P>0.05) bighorn sheep survival following commingling with other ungulates. The absence of epizootic respiratory disease in this experiment supports the hypothesized role of M. ovipneumoniae as a key pathogen of epizootic pneumonia in bighorn sheep commingled with domestic sheep.

78 FR 51678 - Market Tests of Experimental Postal Products

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-21

...] Market Tests of Experimental Postal Products AGENCY: Postal Regulatory Commission. ACTION: Proposed rule... tests of experimental products. The proposed rules address the contents of market test filings, describe... Tests I. Introduction The Commission proposes to establish rules governing market tests of experimental...

A means to estimate thermal and kinetic parameters of coal dust layer from hot surface ignition tests.

PubMed

Park, Haejun; Rangwala, Ali S; Dembsey, Nicholas A

2009-08-30

A method to estimate thermal and kinetic parameters of Pittsburgh seam coal subject to thermal runaway is presented using the standard ASTM E 2021 hot surface ignition test apparatus. Parameters include thermal conductivity (k), activation energy (E), coupled term (QA) of heat of reaction (Q) and pre-exponential factor (A) which are required, but rarely known input values to determine the thermal runaway propensity of a dust material. Four different dust layer thicknesses: 6.4, 12.7, 19.1 and 25.4mm, are tested, and among them, a single steady state dust layer temperature profile of 12.7 mm thick dust layer is used to estimate k, E and QA. k is calculated by equating heat flux from the hot surface layer and heat loss rate on the boundary assuming negligible heat generation in the coal dust layer at a low hot surface temperature. E and QA are calculated by optimizing a numerically estimated steady state dust layer temperature distribution to the experimentally obtained temperature profile of a 12.7 mm thick dust layer. Two unknowns, E and QA, are reduced to one from the correlation of E and QA obtained at criticality of thermal runaway. The estimated k is 0.1 W/mK matching the previously reported value. E ranges from 61.7 to 83.1 kJ/mol, and the corresponding QA ranges from 1.7 x 10(9) to 4.8 x 10(11)J/kg s. The mean values of E (72.4 kJ/mol) and QA (2.8 x 10(10)J/kg s) are used to predict the critical hot surface temperatures for other thicknesses, and good agreement is observed between measured and experimental values. Also, the estimated E and QA ranges match the corresponding ranges calculated from the multiple tests method and values reported in previous research.

Statistical reporting inconsistencies in experimental philosophy

PubMed Central

Colombo, Matteo; Duev, Georgi; Nuijten, Michèle B.; Sprenger, Jan

2018-01-01

Experimental philosophy (x-phi) is a young field of research in the intersection of philosophy and psychology. It aims to make progress on philosophical questions by using experimental methods traditionally associated with the psychological and behavioral sciences, such as null hypothesis significance testing (NHST). Motivated by recent discussions about a methodological crisis in the behavioral sciences, questions have been raised about the methodological standards of x-phi. Here, we focus on one aspect of this question, namely the rate of inconsistencies in statistical reporting. Previous research has examined the extent to which published articles in psychology and other behavioral sciences present statistical inconsistencies in reporting the results of NHST. In this study, we used the R package statcheck to detect statistical inconsistencies in x-phi, and compared rates of inconsistencies in psychology and philosophy. We found that rates of inconsistencies in x-phi are lower than in the psychological and behavioral sciences. From the point of view of statistical reporting consistency, x-phi seems to do no worse, and perhaps even better, than psychological science. PMID:29649220

Numerical validation of selected computer programs in nonlinear analysis of steel frame exposed to fire

NASA Astrophysics Data System (ADS)

Maślak, Mariusz; Pazdanowski, Michał; Woźniczka, Piotr

2018-01-01

Validation of fire resistance for the same steel frame bearing structure is performed here using three different numerical models, i.e. a bar one prepared in the SAFIR environment, and two 3D models developed within the framework of Autodesk Simulation Mechanical (ASM) and an alternative one developed in the environment of the Abaqus code. The results of the computer simulations performed are compared with the experimental results obtained previously, in a laboratory fire test, on a structure having the same characteristics and subjected to the same heating regimen. Comparison of the experimental and numerically determined displacement evolution paths for selected nodes of the considered frame during the simulated fire exposure constitutes the basic criterion applied to evaluate the validity of the numerical results obtained. The experimental and numerically determined estimates of critical temperature specific to the considered frame and related to the limit state of bearing capacity in fire have been verified as well.

The effect of incorporating different concentrations of chlorhexidine digluconate on the degree of conversion of an experimental adhesive resin.

PubMed

Moharam, Lamiaa-Mahmoud; Salem, Haidy-Nabil; Elgamily, Hanaa-Mahmoud

2018-04-01

The aim of this study was to evaluate the effect of chlorhexidine digluconate incorporation on the degree of conversion of an experimental adhesive resin. The experimental resin was prepared from 70 wt% bisphenol A glycerolate dimethacrylate, 30 wt% hydroxyethyl methacrylate, silanized SiO2 nanofillers, 0.5% of camphorquinone and ethyl 4-dimethylaminebenzoate (binary photo-initiator system). Five chlorhexidine digluconate concentrations (0, 0.5, 1, 2 and 4 wt%) were then incorporated into the experimental resin. Thirty Potassium Bromide pellets were prepared then divided into six groups (n=5/group), repre¬senting the tested adhesive resins (Single Bond 2, 0, 0.5, 1, 2 and 4 wt% chlohexidine-incorporated experimental adhesive resins), that were applied to the pellets without light-curing (uncured specimens). Another 30 pellets were prepared and treated with the previous materials then light-cured using LED light-curing device (cured specimens). Degree of conversion of the uncured and the cured specimens were evaluated using FTIR analysis. Adper Single Bond 2 showed the highest degree of conversion mean values followed by 0.5 wt% chlorhexidine concentration then 2 wt% followed by 4 wt% then 1 wt% concentrations, while 0 wt% concentration showed the lowest mean values. Chlorhexidine digluconate had slight significant influence on the efficiency of polymerization of the experimental adhesive resin. Key words: Chlorhexidine digluconate, different concentrations, degree of conversion, experimental adhesive resin.

Report on tests of a CAST 10 airfoil with fixed transition in the T2 transonic cryogenic wind tunnel with self-adaptive walls

NASA Technical Reports Server (NTRS)

Seraudie, A.; Blanchard, A.; Breil, J. F.

1985-01-01

Described are tests on the CAST 10 airfoil in tripped-transition, carried out in the cryogenic and transonic wind-tunnel T2 fitted with self-adaptive walls. These tests follow those which were performed in natural transition and were presented in a previous note. Firstly, a complement was realized to pinpoint the location of the natural transition on the upper surface of the airfoil; this was done by a longitudinal exploration in the boundary layer. Secondly, in a first stage, the transition was only tripped on the lower surface with a carborundum strip of 0.045 mm thickness, situated at 5% of chord (T 1/2 D). These tests were performed here to separate the phenomena in relation to the lower surface and those in relation to the upper surface which occur in natural transition (TN). In a second stage, the transition was normally tripped on both sides of the profile (TD), likewise at x/c = 5% and h = 0.045 mm. The test configurations of the previous serial were experimented again and results obtained in the three cases (TN), (T 1/2 N) and (TD) were compared, in particular those concerned with the effect of the Reynolds number on aerodynamic coefficients of the airfoil. The gathering of the experimental values around a Reynolds number of 20 millions is observed; but before this number, the evolutions of the curves in the three cases tested are different.

The Effects of Smartphone-based Nebulizer Therapy Education on Parents' Knowledge and Confidence of Performance in Caring for Children with Respiratory Disease.

PubMed

Lee, Jung Min; Kim, Shin-Jeong; Min, Hae Young

This study aimed to identify the effects of smartphone-based nebulizer therapy education on the knowledge and confidence of parents while performing care for their children with respiratory disease. This quasi-experimental study employed a pretest-posttest design using a nonequivalent control group. Data were collected from children's parents who had not used nebulizer therapy for their children previously. Both the groups were given nebulizer therapy education using the same content but different learning methods. The experimental group (n=36) was taught using smartphones, while the control group (n=36) was taught using verbal and paper-based methods. The data were analyzed using the Chi Square test, repeated measures analysis of variance, and t-test. The mean scores on knowledge improvement (F=100.949, p<0.001) and confidence in performing care (t=-6.959, p<0.001) were significantly higher for the experimental group as compared to the control group. Further, the scores on satisfaction with the learning method were significantly higher for the experimental group as compared to the control group (t=-5.819, p<0.001). Our results suggest that smartphone-based education on nebulizer therapy might be effective in improving parents' knowledge and confidence in performing care for their children. This study suggests that smartphone-based education needs to be considered as an effective educational intervention in providing nursing support for parents of children with respiratory disease. Copyright © 2017 Elsevier Inc. All rights reserved.

Engineering platform and experimental protocol for design and evaluation of a neurally-controlled powered transfemoral prosthesis.

PubMed

Zhang, Fan; Liu, Ming; Harper, Stephen; Lee, Michael; Huang, He

2014-07-22

To enable intuitive operation of powered artificial legs, an interface between user and prosthesis that can recognize the user's movement intent is desired. A novel neural-machine interface (NMI) based on neuromuscular-mechanical fusion developed in our previous study has demonstrated a great potential to accurately identify the intended movement of transfemoral amputees. However, this interface has not yet been integrated with a powered prosthetic leg for true neural control. This study aimed to report (1) a flexible platform to implement and optimize neural control of powered lower limb prosthesis and (2) an experimental setup and protocol to evaluate neural prosthesis control on patients with lower limb amputations. First a platform based on a PC and a visual programming environment were developed to implement the prosthesis control algorithms, including NMI training algorithm, NMI online testing algorithm, and intrinsic control algorithm. To demonstrate the function of this platform, in this study the NMI based on neuromuscular-mechanical fusion was hierarchically integrated with intrinsic control of a prototypical transfemoral prosthesis. One patient with a unilateral transfemoral amputation was recruited to evaluate our implemented neural controller when performing activities, such as standing, level-ground walking, ramp ascent, and ramp descent continuously in the laboratory. A novel experimental setup and protocol were developed in order to test the new prosthesis control safely and efficiently. The presented proof-of-concept platform and experimental setup and protocol could aid the future development and application of neurally-controlled powered artificial legs.

Male resource defense mating system in primates? An experimental test in wild capuchin monkeys.

PubMed

Tiddi, Barbara; Heistermann, Michael; Fahy, Martin K; Wheeler, Brandon C

2018-01-01

Ecological models of mating systems provide a theoretical framework to predict the effect of the defendability of both breeding resources and mating partners on mating patterns. In resource-based mating systems, male control over breeding resources is tightly linked to female mating preference. To date, few field studies have experimentally investigated the relationship between male resource control and female mating preference in mammals due to difficulties in manipulating ecological factors (e.g., food contestability). We tested the within-group male resource defense hypothesis experimentally in a wild population of black capuchin monkeys (Sapajus nigritus) in Iguazú National Park, Argentina. Sapajus spp. represent an ideal study model as, in contrast to most primates, they have been previously argued to be characterized by female mate choice and a resource-based mating system in which within-group resource monopolization by high-ranking males drives female mating preference for those males. Here, we examined whether females (N = 12) showed a weaker preference for alpha males during mating seasons in which food distribution was experimentally manipulated to be less defendable relative to those in which it was highly defendable. Results did not support the within-group male resource defense hypothesis, as female sexual preferences for alpha males did not vary based on food defendability. We discuss possible reasons for our results, including the possibility of other direct and indirect benefits females receive in exercising mate choice, the potential lack of tolerance over food directed towards females by alpha males, and phylogenetic constraints.

Mechanical and histological characterization of the abdominal muscle. A previous step to modelling hernia surgery.

PubMed

Hernández, B; Peña, E; Pascual, G; Rodríguez, M; Calvo, B; Doblaré, M; Bellón, J M

2011-04-01

The aims of this study are to experimentally characterize the passive elastic behaviour of the rabbit abdominal wall and to develop a mechanical constitutive law which accurately reproduces the obtained experimental results. For this purpose, tissue samples from New Zealand White rabbits 2150±50 (g) were mechanically tested in vitro. Mechanical tests, consisting of uniaxial loading on tissue samples oriented along the craneo-caudal and the perpendicular directions, respectively, revealed the anisotropic non-linear mechanical behaviour of the abdominal tissues. Experiments were performed considering the composite muscle (including external oblique-EO, internal oblique-IO and transverse abdominis-TA muscle layers), as well as separated muscle layers (i.e., external oblique, and the bilayer formed by internal oblique and transverse abdominis). Both the EO muscle layer and the IO-TA bilayer demonstrated a stiffer behaviour along the transversal direction to muscle fibres than along the longitudinal one. The fibre arrangement was measured by means of a histological study which confirmed that collagen fibres are mainly responsible for the passive mechanical strength and stiffness. Furthermore, the degree of anisotropy of the abdominal composite muscle turned out to be less pronounced than those obtained while studying the EO and IO-TA separately. Moreover, a phenomenological constitutive law was used to capture the measured experimental curves. A Levenberg-Marquardt optimization algorithm was used to fit the model constants to reproduce the experimental curves. Copyright © 2010 Elsevier Ltd. All rights reserved.

Is the rotation of the femoral head a potential initiation for cutting out? A theoretical and experimental approach.

PubMed

Lenich, Andreas; Bachmeier, Samuel; Prantl, Lukas; Nerlich, Michael; Hammer, Jochen; Mayr, Edgar; Al-Munajjed, Amir Andreas; Füchtmeier, Bernd

2011-04-22

Since cut-out still remains one of the major clinical challenges in the field of osteoporotic proximal femur fractures, remarkable developments have been made in improving treatment concepts. However, the mechanics of these complications have not been fully understood.We hypothesize using the experimental data and a theoretical model that a previous rotation of the femoral head due to de-central implant positioning can initiate a cut-out. In this investigation we analysed our experimental data using two common screws (DHS/Gamma 3) and helical blades (PFN A/TFN) for the fixation of femur fractures in a simple theoretical model applying typical gait pattern on de-central positioned implants. In previous tests during a forced implant rotation by a biomechanical testing machine in a human femoral head the two screws showed failure symptoms (2-6Nm) at the same magnitude as torques acting in the hip during daily activities with de-central implant positioning, while the helical blades showed a better stability (10-20Nm).To calculate the torque of the head around the implant only the force and the leverarm is needed (N [Nm] = F [N] * × [m]). The force F is a product of the mass M [kg] multiplied by the acceleration g [m/s2]. The leverarm is the distance between the center of the head of femur and the implant center on a horizontal line. Using 50% of 75 kg body weight a torque of 0.37Nm for the 1 mm decentralized position and 1.1Nm for the 3 mm decentralized position of the implant was calculated. At 250% BW, appropriate to a normal step, torques of 1.8Nm (1 mm) and 5.5Nm (3 mm) have been calculated.Comparing of the experimental and theoretical results shows that both screws fail in the same magnitude as torques occur in a more than 3 mm de-central positioned implant. We conclude the center-center position in the head of femur of any kind of lag screw or blade is to be achieved to minimize rotation of the femoral head and to prevent further mechanical complications.

Effects of a home-exercise therapy programme on cervical and lumbar range of motion among nurses with neck and lower back pain: a quasi-experimental study.

PubMed

Freimann, Tiina; Merisalu, Eda; Pääsuke, Mati

2015-01-01

Cervical and lumbar range of motion limitations are usually associated with musculoskeletal pain in the neck and lower back, and are a major health problem among nurses. Physical exercise has been evaluated as an effective intervention method for improving cervical and lumbar range of motion, and for preventing and reducing musculoskeletal pain. The purpose of this study was to investigate the effects of a home-exercise therapy programme on cervical and lumbar range of motion among intensive care unit nurses who had experienced mild to moderate musculoskeletal pain in the neck and or lower back during the previous six months. A quasi-experimental study was conducted among intensive care unit nurses at Tartu University Hospital (Estonia) between May and July 2011. Thirteen nurses who had suffered musculoskeletal pain episodes in the neck and or lower back during the previous six months underwent an 8-week home-exercise therapy programme. Eleven nurses without musculoskeletal pain formed a control group. Questions from the Nordic Musculoskeletal Questionnaire and the 11-point Visual Analogue Scale were used to select potential participants for the experimental group via an assessment of the prevalence and intensity of musculoskeletal pain. Cervical range of motion and lumbar range of motion in flexion, extension, lateral flexion and (cervical range of motion only) rotation were measured with a digital goniometer. A paired t-test was used to compare the measured parameters before and after the home-exercise therapy programme. A Student's t-test was used to analyse any differences between the experimental and control groups. After the home-exercise therapy, there was a significant increase (p < 0.05) in cervical range of motion in flexion, extension, lateral flexion and rotation, and in lumbar range of motion in lateral flexion. Cervical range of motion in flexion was significantly higher (p < 0.01) in the experimental group compared to the control group after therapy. Our results suggest an 8-week intensive home-exercise therapy programme may improve cervical and lumbar range of motion among intensive care nurses. Further studies are needed to develop this simple but effective home-exercise therapy programme to help motivate nurses to perform such exercises regularly. Current Controlled Trials ISRCTN19278735. Registered 27 November 2015.

Further wind tunnel investigation of the SM701 airfoil with aileron and turbulators

NASA Technical Reports Server (NTRS)

Steen, Gregory; Nicks, Oran; Heffner, Michael

1992-01-01

Wind tunnel tests were performed on a two-dimensional model of the SM701 airfoil designed for use on the World Class gliders. The test covered a range of Reynolds numbers from 500,000 to 1.7 million. Aerodynamic forces and moments were measured with an external balance. Momentum loss method measurements of the section drag coefficient were also made. Flow visualization techniques provided information on transition from laminar to turbulent flow. Lift, drag, and pitching moment were analyzed and comparisons were made with predicted and previously obtained experimental data. The effects of V-tape turbulators for use in turbulent drag reduction were studied. The performance of a 25 percent chord aileron deflected through plus or minus 20 degrees was researched. The model was designed, constructed, and tested by students at Texas A&M University.

Recognising 'social' and 'non-social' emotions in self and others: a study of autism.

PubMed

Williams, David; Happé, Francesca

2010-07-01

Studies of emotion processing in autism have produced mixed results, with fewer studies observing autism-specific deficits than might be imagined. In the current study, 21 individuals with autism and 21 age- and ability-matched, learning disabled comparison participants were tested for their ability to (a) recognise, in others, expressions of 'social' emotions (e.g., embarrassment) and 'non-social' emotions (e.g., happiness) and; (b) report their own previous experiences of each of these emotions. In line with predictions, amongst both groups of participants, social emotions were more difficult to recognise and report than non-social emotions. Also amongst both groups, the ability to report social emotion-experience was significantly associated with the ability to recognise social emotions in others, independent of age and verbal ability. However, contrary to predictions, no between-group differences in levels or patterns of performance on the experimental tasks were observed. In light of previous research, these results suggest either that emotion-processing is not as specifically impaired in autism as is traditionally thought to be the case, or that individuals with autism are implementing compensatory strategies to succeed on experimental tasks in the absence of emotion-processing competence.

Verbal and visual learning of science terminology by high school biology students

NASA Astrophysics Data System (ADS)

Grant, Andrew Morton

The purpose of this study is to determine whether scientific terms with multiple meanings are more easily learned when taught pictorially or when taught verbally. The question of interference from previously known colloquial meanings is addressed as well. In carrying out this study, an experimental group of 30 students was taught pictorially and a control group of 30 students was taught verbally. Each group was made up of male and female students from the dominant culture (Caucasian) and from alternate cultures (mainly African American and Asian). The age of the participants was between 14 and 17. Students were selected as class groups. There were four class groups in the study. Class groups were assigned to the experimental or control group by random selection. Results were compared by use of a pre-test and post-test procedure. Students were asked to verbally describe 41 terms having scientific and colloquial meanings; they were to give the scientific meaning, if known, the colloquial if not, or leave a question mark if the term was unknown. They were then asked to draw a picture of the meaning of the term, if known. The same instructions were given to both groups. A series of seven hypotheses were identified. These hypotheses considered learning outcomes related to instructional mode as well as outcomes related to gender and cultural differences. An attempt was made to determine the similarity of the experimental and control groups. Student profiles, a learning styles inventory, and an imbedded image test all showed an initial similarity of the two groups. Once the pretest and posttest were given, data were analyzed by the use of the Chi-square of Association, the McNemar Chi-square, and Z scores (at.05 significance level). Results indicated significant differences in outcomes between the experimental group and the control group. The experimental group showed more science vocabulary learning than the control group and experienced more interference from the colloquial meanings of the terms used. Gender and cultural relationships were tested both between groups and within groups. Significant gender differences were found between groups. The patterns of response described in the experimental group were attributed to the method of pictorial instruction given this group.

Simultaneous optimization method for absorption spectroscopy postprocessing.

PubMed

Simms, Jean M; An, Xinliang; Brittelle, Mack S; Ramesh, Varun; Ghandhi, Jaal B; Sanders, Scott T

2015-05-10

A simultaneous optimization method is proposed for absorption spectroscopy postprocessing. This method is particularly useful for thermometry measurements based on congested spectra, as commonly encountered in combustion applications of H2O absorption spectroscopy. A comparison test demonstrated that the simultaneous optimization method had greater accuracy, greater precision, and was more user-independent than the common step-wise postprocessing method previously used by the authors. The simultaneous optimization method was also used to process experimental data from an environmental chamber and a constant volume combustion chamber, producing results with errors on the order of only 1%.

A Thermal Stability Test for Primary Explosive Stab Sensitizers: Study of the Thermal and Hydrolytic Stability of 2-Picryl-5-Nitrotetrazole,

DTIC Science & Technology

1984-02-01

have been described previously (2]. The actual batch used was designated Batch D and was identical to that referred to as Batch C in Reference [2...Tetrazene was type RD1357 prepared at Materials Research Laboratories. The batch used was designated Batch 10/83(A). Lead Azide was type RD1343 and was...Preparation of Experimental Detonators Eperimental detonators were prepared in mild steel tubes, 6 mm o.d., 3.2 mm i.d., length 6 mm, prepared from

Single Axis Attitude Control and DC Bus Regulation with Two Flywheels

NASA Technical Reports Server (NTRS)

Kascak, Peter E.; Jansen, Ralph H.; Kenny, Barbara; Dever, Timothy P.

2002-01-01

A computer simulation of a flywheel energy storage single axis attitude control system is described. The simulation models hardware which will be experimentally tested in the future. This hardware consists of two counter rotating flywheels mounted to an air table. The air table allows one axis of rotational motion. An inertia DC bus coordinator is set forth that allows the two control problems, bus regulation and attitude control, to be separated. Simulation results are presented with a previously derived flywheel bus regulator and a simple PID attitude controller.

Progress of Rugby Hohlraum Experiments on Omega

NASA Astrophysics Data System (ADS)

Philippe, Franck; Tassin, Veronique; Casner, Alexis; Gauthier, Pascal; Seytor, Patricia; Monteil, Marie-Christine; Park, Hye-Sook; Robey, Harry; Ross, Steven; Amendt, Peter; Girard, Frederic; Villette, Bruno; Reverdin, Charles; Loiseau, Pascal; Caillaud, Tony; Landoas, Olivier; Li, Chi Kang; Petrasso, Richard; Seguin, Fredrick; Rosenberg, Markus

2011-10-01

The rugby hohlraum concept is predicted to enable better coupling and higher gains in the indirect drive approach to ignition. A collaborative experimental program is currently pursued on OMEGA to test this concept in preparation for future megajoule-scale ignition designs. A direct comparison of gas-filled rugby hohlraums with classical cylinders was recently performed, showing a significant (up to ~40%) observed x-ray drive enhancement and neutron yields that are consistently higher in the rugby case. This work extends and confirms our previous findings in empty rugby hohlraums.

Analysis of advanced solid rocket motor ignition phenomena

NASA Technical Reports Server (NTRS)

Foster, Winfred A., Jr.; Jenkins, Rhonald M.

1995-01-01

This report presents the results obtained from an experimental analysis of the flow field in the slots of the star grain section in the head-end of the advanced solid rocket motor during the ignition transient. This work represents an extension of the previous tests and analysis to include the effects of using a center port in conjunction with multiple canted igniter ports. The flow field measurements include oil smear data on the star slot walls, pressure and heat transfer coefficient measurements on the star slot walls and velocity measurements in the star slot.

Determination of the Gravitational Constant with a Beam Balance

NASA Astrophysics Data System (ADS)

Schlamminger, St.; Holzschuh, E.; Kündig, W.

2002-09-01

The Newtonian gravitational constant G was determined by means of a novel beam-balance experiment with an accuracy comparable to that of the most precise torsion-balance experiments. The gravitational force of two stainless steel tanks filled with 13 521kg mercury on 1.1kg test masses was measured using a commercial mass comparator. A careful analysis of the data and the experimental error yields G=6.674 07(22)×10-11 m3 kg-1 s-2. This value is in excellent agreement with most values previously obtained with different methods.

First experimental evidence of hydrodynamic tunneling of ultra–relativistic protons in extended solid copper target at the CERN HiRadMat facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schmidt, R.; Grenier, D.; Wollmann, D.

2014-08-15

A novel experiment has been performed at the CERN HiRadMat test facility to study the impact of the 440 GeV proton beam generated by the Super Proton Synchrotron on extended solid copper cylindrical targets. Substantial hydrodynamic tunneling of the protons in the target material has been observed that leads to significant lengthening of the projectile range, which confirms our previous theoretical predictions [N. A. Tahir et al., Phys. Rev. Spec. Top.-Accel. Beams 15, 051003 (2012)]. Simulation results show very good agreement with the experimental measurements. These results have very important implications on the machine protection design for powerful machines like themore » Large Hadron Collider (LHC), the future High Luminosity LHC, and the proposed huge 80 km circumference Future Circular Collider, which is currently being discussed at CERN. Another very interesting outcome of this work is that one may also study the field of High Energy Density Physics at this test facility.« less

A laboratory validation study of the time-lapse oscillatory pumping test concept for leakage detection in geological repositories

NASA Astrophysics Data System (ADS)

Sun, A. Y.; Islam, A.; Lu, J.

2017-12-01

Time-lapse oscillatory pumping test (OPT) has been introduced recently as a pressure-based monitoring technique for detecting potential leakage in geologic repositories. By routinely conducting OPT at a number of pulsing frequencies, a site operator may identify the potential anomalies in the frequency domain, alleviating the ambiguity caused by reservoir noise and improving the signal-to-noise ratio. Building on previous theoretical and field studies, this work performed a series of laboratory experiments to validate the concept of time-lapse OPT using a custom made, stainless steel tank under relatively high pressures ( 120psi). The experimental configuration simulates a miniature geologic storage repository consisting of three layers (i.e., injection zone, caprock, and above-zone aquifer). Results show that leakage in the injection zone led to deviations in the power spectrum of observed pressure data, and the amplitude of which also increases with decreasing pulsing frequencies. The experimental results were further analyzed by developing a 3D flow model, using which the model parameters were estimated through frequency domain inversion.

Jet-Surface Interaction Test: Flow Measurements Results

NASA Technical Reports Server (NTRS)

Brown, Cliff; Wernet, Mark

2014-01-01

Modern aircraft design often puts the engine exhaust in close proximity to the airframe surfaces. Aircraft noise prediction tools must continue to develop in order to meet the challenges these aircraft present. The Jet-Surface Interaction Tests have been conducted to provide a comprehensive quality set of experimental data suitable for development and validation of these exhaust noise prediction methods. Flow measurements have been acquired using streamwise and cross-stream particle image velocimetry (PIV) and fluctuating surface pressure data acquired using flush mounted pressure transducers near the surface trailing edge. These data combined with previously reported far-field and phased array noise measurements represent the first step toward the experimental data base. These flow data are particularly applicable to development of noise prediction methods which rely on computational fluid dynamics to uncover the flow physics. A representative sample of the large flow data set acquired is presented here to show how a surface near a jet affects the turbulent kinetic energy in the plume, the spatial relationship between the jet plume and surface needed to generate surface trailing-edge noise, and differences between heated and unheated jet flows with respect to surfaces.

Progress in Validation of Wind-US for Ramjet/Scramjet Combustion

NASA Technical Reports Server (NTRS)

Engblom, William A.; Frate, Franco C.; Nelson, Chris C.

2005-01-01

Validation of the Wind-US flow solver against two sets of experimental data involving high-speed combustion is attempted. First, the well-known Burrows- Kurkov supersonic hydrogen-air combustion test case is simulated, and the sensitively of ignition location and combustion performance to key parameters is explored. Second, a numerical model is developed for simulation of an X-43B candidate, full-scale, JP-7-fueled, internal flowpath operating in ramjet mode. Numerical results using an ethylene-air chemical kinetics model are directly compared against previously existing pressure-distribution data along the entire flowpath, obtained in direct-connect testing conducted at NASA Langley Research Center. Comparison to derived quantities such as burn efficiency and thermal throat location are also made. Reasonable to excellent agreement with experimental data is demonstrated for key parameters in both simulation efforts. Additional Wind-US feature needed to improve simulation efforts are described herein, including maintaining stagnation conditions at inflow boundaries for multi-species flow. An open issue regarding the sensitivity of isolator unstart to key model parameters is briefly discussed.

GPCR-I-TASSER: A Hybrid Approach to G Protein-Coupled Receptor Structure Modeling and the Application to the Human Genome.

PubMed

Zhang, Jian; Yang, Jianyi; Jang, Richard; Zhang, Yang

2015-08-04

Experimental structure determination remains difficult for G protein-coupled receptors (GPCRs). We propose a new hybrid protocol to construct GPCR structure models that integrates experimental mutagenesis data with ab initio transmembrane (TM) helix assembly simulations. The method was tested on 24 known GPCRs where the ab initio TM-helix assembly procedure constructed the correct fold for 20 cases. When combined with weak homology and sparse mutagenesis restraints, the method generated correct folds for all the tested cases with an average Cα root-mean-square deviation 2.4 Å in the TM regions. The new hybrid protocol was applied to model all 1,026 GPCRs in the human genome, where 923 have a high confidence score and are expected to have correct folds; these contain many pharmaceutically important families with no previously solved structures, including Trace amine, Prostanoids, Releasing hormones, Melanocortins, Vasopressin, and Neuropeptide Y receptors. The results demonstrate new progress on genome-wide structure modeling of TM proteins. Copyright © 2015 Elsevier Ltd. All rights reserved.

Experimental Detection and Characterization of Void using Time-Domain Reflection Wave

NASA Astrophysics Data System (ADS)

Zahari, M. N. H.; Madun, A.; Dahlan, S. H.; Joret, A.; Zainal Abidin, M. H.; Mohammad, A. H.; Omar, A. H.

2018-04-01

Recent technologies in engineering views have brought the significant improvement in terms of performance and precision. One of those improvements is in geophysics studies for underground detection. Reflection method has been demonstrated to able to detect and locate subsurface anomalies in previous studies, including voids. Conventional method merely involves field testing only for limited areas. This may lead to undiscovered of the void position. Problems arose when the voids were not recognised in early stage and thus, causing hazards, costs increment, and can lead to serious accidents and structural damages. Therefore, to achieve better certainty of the site investigation, a dynamic approach is needed to be implemented. To estimate and characterize the anomalies signal in a better way, an attempt has been made to model air-filled void as experimental testing at site. Robust detection and characterization of voids through inexpensive cost using reflection method are proposed to improve the detectability and characterization of the void. The result shows 2-Dimensional and 3-Dimensional analyses of void based on reflection data with P-waves velocity at 454.54 m/s.

Fracture simulation of elastomer blended polypropylene based on elastoviscoplastic constitutive equation with craze and tensile softening law

NASA Astrophysics Data System (ADS)

Mae, H.

2006-08-01

The strong strain-rate dependence, neck propagation and craze evolution characterize the large plastic deformation and fracture behavior of polymer. In the latest study, Kobayashi, Tomii and Shizawa suggested the elastoviscoplastic constitutive equation based on craze evolution and annihilation and then applied it to the plane strain issue of polymer. In the previous study, the author applied their suggested elastoviscoplastic constitutive equation with craze effect to the three dimensional shell and then showed that the load displacement history was in good agreement with the experimental result including only microscopic crack such as crazes. For the future industrial applications, the macroscopic crack has to be taken into account. Thus, the main objective of this study is to propose the tensile softening equation and then add it to the elastoviscoplastic constitutive equation with craze effect so that the load displacement history can be roughly simulated during the macroscopic crack propagation. The tested material in this study is the elastomer blended polypropylene used in the interior and exterior of automobiles. First, the material properties are obtained based on the tensile test results at wide range of strain rates: 10 - 4-102 (1/sec). Next, the compact tension test is conducted and then the tensile softening parameters are fixed. Then, the dart impact test is carried out in order to obtain the load displacement history and also observe the macroscopic crack propagation at high strain rate. Finally, the fracture behavior is simulated and then compared with the experimental results. It is shown that the predictions of the constitutive equation with the proposed tensile softening equation are in good agreement with the experimental results for the future industrial applications.

Tensile and compressive behavior of Borsic/aluminum

NASA Technical Reports Server (NTRS)

Herakovich, C. T.; Davis, J. G., Jr.; Viswanathan, C. N.

1977-01-01

The results of an experimental investigation of the mechanical behavior of Borsic/aluminum are presented. Composite laminates were tested in tension and compression for monotonically increasing load and also for variable loading cycles in which the maximum load was increased in each successive cycle. It is shown that significant strain-hardening, and corresponding increase in yield stress, is exhibited by the metal matrix laminates. For matrix dominated laminates, the current yield stress is essentially identical to the previous maximum stress, and unloading is essentially linear with large permanent strains after unloading. For laminates with fiber dominated behavior, the yield stress increases with increase in the previous maximum stress, but the increase in yield stress does not keep pace with the previous maximum stress. These fiber dominated laminates exhibit smaller nonlinear strains, reversed nonlinear behavior during unloading, and smaller permanent strains after unloading. Compression results from sandwich beams and flat coupons are shown to differ considerably. Results from beam specimens tend to exhibit higher values for modulus, yield stress, and strength.

Investigating the encoding-retrieval match in recognition memory: effects of experimental design, specificity, and retention interval.

PubMed

Dewhurst, Stephen A; Knott, Lauren M

2010-12-01

Five experiments investigated the encoding-retrieval match in recognition memory by manipulating read and generate conditions at study and at test. Experiments 1A and 1B confirmed previous findings that reinstating encoding operations at test enhances recognition accuracy in a within-groups design but reduces recognition accuracy in a between-groups design. Experiment 2A showed that generating from anagrams at study and at test enhanced recognition accuracy even when study and test items were generated from different anagrams. Experiment 2B showed that switching from one generation task at study (e.g., anagram solution) to a different generation task at test (e.g., fragment completion) eliminated this recognition advantage. Experiment 3 showed that the recognition advantage found in Experiment 1A is reliably present up to 1 week after study. The findings are consistent with theories of memory that emphasize the importance of the match between encoding and retrieval operations.

A Battery Certification Testbed for Small Satellite Missions

NASA Technical Reports Server (NTRS)

Cameron, Zachary; Kulkarni, Chetan S.; Luna, Ali Guarneros; Goebel, Kai; Poll, Scott

2015-01-01

A battery pack consisting of standard cylindrical 18650 lithium-ion cells has been chosen for small satellite missions based on previous flight heritage and compliance with NASA battery safety requirements. However, for batteries that transit through the International Space Station (ISS), additional certification tests are required for individual cells as well as the battery packs. In this manuscript, we discuss the development of generalized testbeds for testing and certifying different types of batteries critical to small satellite missions. Test procedures developed and executed for this certification effort include: a detailed physical inspection before and after experiments; electrical cycling characterization at the cell and pack levels; battery-pack overcharge, over-discharge, external short testing; battery-pack vacuum leak and vibration testing. The overall goals of these certification procedures are to conform to requirements set forth by the agency and identify unique safety hazards. The testbeds, procedures, and experimental results are discussed for batteries chosen for small satellite missions to be launched from the ISS.

High-pressure calorimeter chamber tests for liquid oxygen/kerosene (LOX/RP-1) rocket combustion

NASA Technical Reports Server (NTRS)

Masters, Philip A.; Armstrong, Elizabeth S.; Price, Harold G.

1988-01-01

An experimental program was conducted to investigate the rocket combustion and heat transfer characteristics of liquid oxygen/kerosene (LOX/RP-1) mixtures at high chamber pressures. Two water-cooled calorimeter chambers of different combustion lengths were tested using 37- and 61-element oxidizer-fuel-oxidizer triplet injectors. The tests were conducted at nominal chamber pressures of 4.1, 8.3, and 13.8 MPa abs (600, 1200, and 2000 psia). Heat flux Q/A data were obtained for the entire calorimeter length for oxygen/fuel mixture ratios of 1.8 to 3.3. Test data at 4.1 MPa abs compared favorably with previous test data from another source. Using an injector with a fuel-rich outer zone reduced the throat heat flux by 47 percent with only a 4.5 percent reduction in the characteristic exhaust velocity efficiency C* sub eff. The throat heat transfer coefficient was reduced approximately 40 percent because of carbon deposits on the chamber wall.

Construction of a dual axis force reflection stick and test station

NASA Astrophysics Data System (ADS)

Repperger, Daniel E.; Scarborough, Eric L.; Chelette, Tamara L.

1991-11-01

This report describes the construction of a dual axis force reflecting stick controller and test station which was constructed through the use of basic research funds (ILIR monies). The prototype described in this report is powered only by electric motors and used the latest technology in computers. This was an advancement over a previous prototype which involved pneumatic devices and was very large, bulky, and awkward to use. An experiment was conducted with 5 subjects as described herein to test the overall system for its use in experimental design. The motivation for developing such a small test station for the use of force reflection in stick controllers is because with this new compact and portable system, many new applications now appear for this technology. The system described herein minimizes both weight and electric power requirements to produce the same force reflection. By upgrading the technology in the components used in this test station, wider use of force reflection is now available for a host of new applications.

Shuttle filter study. Volume 2: Contaminant generation and sensitivity studies

NASA Technical Reports Server (NTRS)

1974-01-01

Contaminant generation studies were conducted at the component level using two different methods, radioactive tracer technique and gravimetric analysis test procedure. Both of these were reduced to practice during this program. In the first of these methods, radioactively tagged components typical of those used in spacecraft were studied to determine their contaminant generation characteristics under simulated operating conditions. Because the purpose of the work was: (1) to determine the types and quantities of contaminants generated; and (2) to evaluate improved monitoring and detection schemes, no attempt was made to evaluate or qualify specific components. The components used in this test program were therefore not flight hardware items. Some of them had been used in previous tests; some were obsolete; one was an experimental device. In addition to the component tests, various materials of interest to contaminant and filtration studies were irradiated and evaluated for use as autotracer materials. These included test dusts, plastics, valve seat materials, and bearing cage materials.

Virtual geotechnical laboratory experiments using a simulator

NASA Astrophysics Data System (ADS)

Penumadu, Dayakar; Zhao, Rongda; Frost, David

2000-04-01

The details of a test simulator that provides a realistic environment for performing virtual laboratory experimentals in soil mechanics is presented. A computer program Geo-Sim that can be used to perform virtual experiments, and allow for real-time observations of material response is presented. The results of experiments, for a given set of input parameters, are obtained with the test simulator using well-trained artificial neural-network-based soil models for different soil types and stress paths. Multimedia capabilities are integrated in Geo-Sim, using software that links and controls a laser disc player with a real-time parallel processing ability. During the simulation of a virtual experiment, relevant portions of the video image of a previously recorded test on an actual soil specimen are dispalyed along with the graphical presentation of response from the feedforward ANN model predictions. The pilot simulator developed to date includes all aspects related to performing a triaxial test on cohesionless soil under undrained and drained conditions. The benefits of the test simulator are also presented.

The effect of meditation on shooting performance.

PubMed Central

Solberg, E E; Berglund, K A; Engen, O; Ekeberg, O; Loeb, M

1996-01-01

OBJECTIVE: To study effects of meditation on the shooting performance. METHODS: 25 elite shooters were investigated in an independent groups design. The results in standardised test shootings indoors and in ordinary competitions outdoors were assessed before and after regular meditation training for the experimental group. The experience of tension during the test shootings was self recorded on a visual analogue scale (VAS). RESULTS: The competition results in the outdoor season (1993), just after the meditation training period, compared with the results the previous season (1992), were better in the meditation group (P < 0.05). No significant difference between the groups was observed in the test shootings before and after the relaxation intervention. A significant association was shown between low tension and the results in the test shootings (correlation r = 0.42, P < 0.0001; Wilcoxon rank sum test, z = -3.36, P < 0.001); 18% (= r2) of the variance in performance was explained by tension. CONCLUSIONS: Meditation may enhance competitive shooting performance. PMID:9015599

National Transonic Facility Wall Pressure Calibration Using Modern Design of Experiments (Invited)

NASA Technical Reports Server (NTRS)

Underwood, Pamela J.; Everhart, Joel L.; DeLoach, Richard

2001-01-01

The Modern Design of Experiments (MDOE) has been applied to wind tunnel testing at NASA Langley Research Center for several years. At Langley, MDOE has proven to be a useful and robust approach to aerodynamic testing that yields significant reductions in the cost and duration of experiments while still providing for the highest quality research results. This paper extends its application to include empty tunnel wall pressure calibrations. These calibrations are performed in support of wall interference corrections. This paper will present the experimental objectives, and the theoretical design process. To validate the tunnel-empty-calibration experiment design, preliminary response surface models calculated from previously acquired data are also presented. Finally, lessons learned and future wall interference applications of MDOE are discussed.

Vehicle-scale investigation of a fluorine jet-pump liquid hydrogen tank pressurization system

NASA Technical Reports Server (NTRS)

Cady, E. C.; Kendle, D. W.

1972-01-01

A comprehensive analytical and experimental program was performed to evaluate the performance of a fluorine-hydrogen jet-pump injector for main tank injection (MTI) pressurization of a liquid hydrogen (LH2) tank. The injector performance during pressurization and LH2 expulsion was determined by a series of seven tests of a full-scale injector and MTI pressure control system in a 28.3 cu m (1000 cu ft) flight-weight LH2 tank. Although the injector did not effectively jet-pump LH2 continuously, it showed improved pressurization performance compared to straight-pipe injectors tested under the same conditions in a previous program. The MTI computer code was modified to allow performance prediction for the jet-pump injector.

Description and calibration of the Langley 6- by 19-inch transonic tunnel

NASA Technical Reports Server (NTRS)

Ladson, C. L.

1973-01-01

A description and calibration is presented of the Langley 6- by 19-inch transonic tunnel which is a two-dimensional facility with top and bottom slotted walls used for testing two-dimensional airfoil sections. Basic tunnel-empty Mach number distributions and schlieren flow photographs as well as integrated normal-force coefficients, pitching-moment coefficients, surface-pressure distributions, and schlieren flow photographs of an NACA 0012 airfoil calibration model are presented. The Mach number capability of the facility is from 0.5 to about 1.1 with a corresponding Reynolds number range of 1.5 million to 3 million based on a 4.0-in. model chord. Comparisons of experimental results from the tests with previous data are also presented.

Limited receptive area neural classifier for recognition of swallowing sounds using continuous wavelet transform.

PubMed

Makeyev, Oleksandr; Sazonov, Edward; Schuckers, Stephanie; Lopez-Meyer, Paulo; Melanson, Ed; Neuman, Michael

2007-01-01

In this paper we propose a sound recognition technique based on the limited receptive area (LIRA) neural classifier and continuous wavelet transform (CWT). LIRA neural classifier was developed as a multipurpose image recognition system. Previous tests of LIRA demonstrated good results in different image recognition tasks including: handwritten digit recognition, face recognition, metal surface texture recognition, and micro work piece shape recognition. We propose a sound recognition technique where scalograms of sound instances serve as inputs of the LIRA neural classifier. The methodology was tested in recognition of swallowing sounds. Swallowing sound recognition may be employed in systems for automated swallowing assessment and diagnosis of swallowing disorders. The experimental results suggest high efficiency and reliability of the proposed approach.

Ergodicity convergence test suggests telomere motion obeys fractional dynamics

NASA Astrophysics Data System (ADS)

Kepten, E.; Bronshtein, I.; Garini, Y.

2011-04-01

Anomalous diffusion, observed in many biological processes, is a generalized description of a wide variety of processes, all obeying the same law of mean-square displacement. Identifying the basic mechanisms of these observations is important for deducing the nature of the biophysical systems measured. We implement a previously suggested method for distinguishing between fractional Langevin dynamics, fractional Brownian motion, and continuous time random walk based on the ergodic nature of the data. We apply the method together with the recently suggested P-variation test and the displacement correlation to the lately measured dynamics of telomeres in the nucleus of mammalian cells and find strong evidence that the telomeres motion obeys fractional dynamics. The ergodic dynamics are observed experimentally to fit fractional Brownian or Langevin dynamics.

A multiscale strength model for tantalum over an extended range of strain rates

NASA Astrophysics Data System (ADS)

Barton, N. R.; Rhee, M.

2013-09-01

A strength model for tantalum is developed and exercised across a range of conditions relevant to various types of experimental observations. The model is based on previous multiscale modeling work combined with experimental observations. As such, the model's parameterization includes a hybrid of quantities that arise directly from predictive sub-scale physics models and quantities that are adjusted to align the model with experimental observations. Given current computing and experimental limitations, the response regions for sub-scale physics simulations and detailed experimental observations have been largely disjoint. In formulating the new model and presenting results here, attention is paid to integrated experimental observations that probe strength response at the elevated strain rates where a previous version of the model has generally been successful in predicting experimental data [Barton et al., J. Appl. Phys. 109(7), 073501 (2011)].

First implementation of burrowing motions in dual-reciprocating drilling using an integrated actuation mechanism

NASA Astrophysics Data System (ADS)

Pitcher, Craig; Gao, Yang

2017-03-01

The dual-reciprocating drill (DRD) is a biologically-inspired low-mass alternative to traditional drilling techniques, using backwards-facing teethed halves to grip the surrounding substrate, generating a traction force that reduces the required overhead penetration force. Previous experiments using a proof-of-concept test bench have provided evidence as to the significant role of sideways movements and lateral forces in improving drilling performance. The system is also progressing to a first system prototype concept, in which an actuation mechanism is integrated within the drill heads. To experimentally determine the effect of lateral motions, a new internal actuation mechanism was developed to allow the inclusion of controlled sideways movements, resulting in the creation of the circular and diagonal burrowing motions. This paper presents an investigation into the performance of the reciprocation and burrowing motions by testing them in a planetary regolith simulant. Analysis of force sensor measurements has shown a relationship between the penetration and traction forces and the internal friction of the mechanism and depth achieved. These tests have also experimentally demonstrated the benefit of lateral motions in drilling performance, with both the burrowing mechanisms and drilling tests performed at an angle able to penetrate further than traditional vertical reciprocation, leading to the proposition of new burrowing and diagonal drilling mechanics. From this, a new fully integrated system prototype can be developed which incorporates lateral motions that can optimise the drilling performance.

Validation of the SimSET simulation package for modeling the Siemens Biograph mCT PET scanner

NASA Astrophysics Data System (ADS)

Poon, Jonathan K.; Dahlbom, Magnus L.; Casey, Michael E.; Qi, Jinyi; Cherry, Simon R.; Badawi, Ramsey D.

2015-02-01

Monte Carlo simulation provides a valuable tool in performance assessment and optimization of system design parameters for PET scanners. SimSET is a popular Monte Carlo simulation toolkit that features fast simulation time, as well as variance reduction tools to further enhance computational efficiency. However, SimSET has lacked the ability to simulate block detectors until its most recent release. Our goal is to validate new features of SimSET by developing a simulation model of the Siemens Biograph mCT PET scanner and comparing the results to a simulation model developed in the GATE simulation suite and to experimental results. We used the NEMA NU-2 2007 scatter fraction, count rates, and spatial resolution protocols to validate the SimSET simulation model and its new features. The SimSET model overestimated the experimental results of the count rate tests by 11-23% and the spatial resolution test by 13-28%, which is comparable to previous validation studies of other PET scanners in the literature. The difference between the SimSET and GATE simulation was approximately 4-8% for the count rate test and approximately 3-11% for the spatial resolution test. In terms of computational time, SimSET performed simulations approximately 11 times faster than GATE simulations. The new block detector model in SimSET offers a fast and reasonably accurate simulation toolkit for PET imaging applications.

New Precise Measurement of the Hyperfine Splitting of Positronium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ishida, A., E-mail: ishida@icepp.s.u-tokyo.ac.jp

Positronium (Ps) is an ideal system for precision test of bound state quantum electrodynamics. The hyperfine splitting (HFS) of the ground state of Ps, which is one of the most precisely tested quantity, has a large discrepancy of 16 ppm (4.5 σ) between previous experiments and theoretical calculation up to O(α{sup 3}lnα{sup −1}) and part of O(α{sup 3}) corrections. A new experiment which reduces possible systematic uncertainties of Ps thermalization effect and nonuniformity of magnetic field was performed. It revealed that the Ps thermalization effect was as large as 10 ± 2 ppm. Treating the thermalization effect correctly, a newmore » result of 203.3942 ± 0.0016(stat., 8.0 ppm) ± 0.0013(sys., 6.4 ppm) GHz was obtained. This result is consistent with theory within 1.1 σ, whereas it disfavors the previous experimental result by 2.6 σ. It shows that the Ps thermalization effect is crucial for precision measurement of HFS. Future prospects for improved precision are briefly discussed.« less

Cognitive Reflection and the Diligent Worker: An Experimental Study of Millennials

PubMed Central

Corgnet, Brice; Hernán Gonzalez, Roberto; Mateo, Ricardo

2015-01-01

Recent studies have shown that despite crucially needing the creative talent of millennials (people born after 1980) organizations have been reluctant to hire young workers because of their supposed lack of diligence. We propose to help resolve this dilemma by studying the determinants of task performance and shirking behaviors of millennials in a laboratory work environment. We find that cognitive ability is a good predictor of task performance in line with previous literature. In contrast with previous research, personality traits do not consistently predict either task performance or shirking behaviors. Shirking behaviors, as measured by the time participants spent browsing the internet for non-work purposes (Cyberloafing), were only explained by the performance on the Cognitive Reflection Test (CRT). This finding echoes recent research in cognitive psychology according to which conventional measures of cognitive ability only assess a narrow concept of rational thinking (the algorithmic mind) that fails to capture individuals’ capacity to reflect and control their impulses. Our findings suggest that hiring diligent millennials relies on the use of novel cognitive measures such as CRT in lieu of standard personality and intelligence tests. PMID:26545244

Cognitive Reflection and the Diligent Worker: An Experimental Study of Millennials.

PubMed

Corgnet, Brice; Hernán Gonzalez, Roberto; Mateo, Ricardo

2015-01-01

Recent studies have shown that despite crucially needing the creative talent of millennials (people born after 1980) organizations have been reluctant to hire young workers because of their supposed lack of diligence. We propose to help resolve this dilemma by studying the determinants of task performance and shirking behaviors of millennials in a laboratory work environment. We find that cognitive ability is a good predictor of task performance in line with previous literature. In contrast with previous research, personality traits do not consistently predict either task performance or shirking behaviors. Shirking behaviors, as measured by the time participants spent browsing the internet for non-work purposes (Cyberloafing), were only explained by the performance on the Cognitive Reflection Test (CRT). This finding echoes recent research in cognitive psychology according to which conventional measures of cognitive ability only assess a narrow concept of rational thinking (the algorithmic mind) that fails to capture individuals' capacity to reflect and control their impulses. Our findings suggest that hiring diligent millennials relies on the use of novel cognitive measures such as CRT in lieu of standard personality and intelligence tests.

ECG Sensor Card with Evolving RBP Algorithms for Human Verification.

PubMed

Tseng, Kuo-Kun; Huang, Huang-Nan; Zeng, Fufu; Tu, Shu-Yi

2015-08-21

It is known that cardiac and respiratory rhythms in electrocardiograms (ECGs) are highly nonlinear and non-stationary. As a result, most traditional time-domain algorithms are inadequate for characterizing the complex dynamics of the ECG. This paper proposes a new ECG sensor card and a statistical-based ECG algorithm, with the aid of a reduced binary pattern (RBP), with the aim of achieving faster ECG human identity recognition with high accuracy. The proposed algorithm has one advantage that previous ECG algorithms lack-the waveform complex information and de-noising preprocessing can be bypassed; therefore, it is more suitable for non-stationary ECG signals. Experimental results tested on two public ECG databases (MIT-BIH) from MIT University confirm that the proposed scheme is feasible with excellent accuracy, low complexity, and speedy processing. To be more specific, the advanced RBP algorithm achieves high accuracy in human identity recognition and is executed at least nine times faster than previous algorithms. Moreover, based on the test results from a long-term ECG database, the evolving RBP algorithm also demonstrates superior capability in handling long-term and non-stationary ECG signals.

Shape plasticity in response to water velocity in the freshwater blenny Salaria fluviatilis.

PubMed

Laporte, M; Claude, J; Berrebi, P; Perret, P; Magnan, P

2016-03-01

A non-random association between an environmental factor and a given trait could be explained by directional selection (genetic determinism) and by phenotypic plasticity (environmental determinism). A previous study showed a significant relationship between morphology and water velocity in Salaria fluviatilis that conformed to functional expectations. The objective of this study was to test whether this relationship could be explained by phenotypic plasticity. Salaria fluviatilis from a Corsican stream were placed in four experimental channels with different water velocities (0, 10, 20 and 30 cm s(-1)) to test whether there was a morphological response associated with this environmental factor. After 28 days, fish shape changed in response to water velocity without any significant growth. Fish in higher water velocities exhibited a more slender body shape and longer anal and caudal fins. These results indicate a high degree of morphological plasticity in riverine populations of S. fluviatilis and suggest that the previous relationship between morphology and water velocity observed in the field may largely be due to an environmental determinism. © 2016 The Fisheries Society of the British Isles.

Daily online testing in large classes: boosting college performance while reducing achievement gaps.

PubMed

Pennebaker, James W; Gosling, Samuel D; Ferrell, Jason D

2013-01-01

An in-class computer-based system, that included daily online testing, was introduced to two large university classes. We examined subsequent improvements in academic performance and reductions in the achievement gaps between lower- and upper-middle class students in academic performance. Students (N = 901) brought laptop computers to classes and took daily quizzes that provided immediate and personalized feedback. Student performance was compared with the same data for traditional classes taught previously by the same instructors (N = 935). Exam performance was approximately half a letter grade above previous semesters, based on comparisons of identical questions asked from earlier years. Students in the experimental classes performed better in other classes, both in the semester they took the course and in subsequent semester classes. The new system resulted in a 50% reduction in the achievement gap as measured by grades among students of different social classes. These findings suggest that frequent consequential quizzing should be used routinely in large lecture courses to improve performance in class and in other concurrent and subsequent courses.

Does dishonesty really invite third-party punishment? Results of a more stringent test.

PubMed

Konishi, Naoki; Ohtsubo, Yohsuke

2015-05-01

Many experiments have demonstrated that people are willing to incur cost to punish norm violators even when they are not directly harmed by the violation. Such altruistic third-party punishment is often considered an evolutionary underpinning of large-scale human cooperation. However, some scholars argue that previously demonstrated altruistic third-party punishment against fairness-norm violations may be an experimental artefact. For example, envy-driven retaliatory behaviour (i.e. spite) towards better-off unfair game players may be misidentified as altruistic punishment. Indeed, a recent experiment demonstrated that participants ceased to inflict third-party punishment against an unfair player once a series of key methodological problems were systematically controlled for. Noticing that a previous finding regarding apparently altruistic third-party punishment against honesty-norm violations may have been subject to methodological issues, we used a different and what we consider to be a more sound design to evaluate these findings. Third-party punishment against dishonest players withstood this more stringent test. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Experimental Guidance for Isospin Symmetry Breaking Calculations via Single Neutron Pickup Reactions

NASA Astrophysics Data System (ADS)

Leach, K. G.; Garrett, P. E.; Bangay, J. C.; Bianco, L.; Demand, G. A.; Finlay, P.; Green, K. L.; Phillips, A. A.; Rand, E. T.; Sumithrarachchi, C. S.; Svensson, C. E.; Triambak, S.; Wong, J.; Ball, G.; Faestermann, T.; Krücken, R.; Hertenberger, R.; Wirth, H.-F.; Towner, I. S.

2013-03-01

Recent activity in superallowed isospin-symmetry-breaking correction calculations has prompted interest in experimental confirmation of these calculation techniques. The shellmodel set of Towner and Hardy (2008) include the opening of specific core orbitals that were previously frozen. This has resulted in significant shifts in some of the δC values, and an improved agreement of the individual corrected {F}t values with the adopted world average of the 13 cases currently included in the high-precision evaluation of Vud. While the nucleus-to-nucleus variation of {F}t is consistent with the conserved-vector-current (CVC) hypothesis of the Standard Model, these new calculations must be thoroughly tested, and guidance must be given for their improvement. Presented here are details of a 64Zn(ěcd, t)63Zn experiment, undertaken to provide such guidance.

New optimization scheme to obtain interaction potentials for oxide glasses

NASA Astrophysics Data System (ADS)

Sundararaman, Siddharth; Huang, Liping; Ispas, Simona; Kob, Walter

2018-05-01

We propose a new scheme to parameterize effective potentials that can be used to simulate atomic systems such as oxide glasses. As input data for the optimization, we use the radial distribution functions of the liquid and the vibrational density of state of the glass, both obtained from ab initio simulations, as well as experimental data on the pressure dependence of the density of the glass. For the case of silica, we find that this new scheme facilitates finding pair potentials that are significantly more accurate than the previous ones even if the functional form is the same, thus demonstrating that even simple two-body potentials can be superior to more complex three-body potentials. We have tested the new potential by calculating the pressure dependence of the elastic moduli and found a good agreement with the corresponding experimental data.

Tupaia belangeri as an experimental animal model for viral infection.

PubMed

Tsukiyama-Kohara, Kyoko; Kohara, Michinori

2014-01-01

Tupaias, or tree shrews, are small mammals that are similar in appearance to squirrels. The morphological and behavioral characteristics of the group have been extensively characterized, and despite previously being classified as primates, recent studies have placed the group in its own family, the Tupaiidae. Genomic analysis has revealed that the genus Tupaia is closer to humans than it is to rodents. In addition, tupaias are susceptible to hepatitis B virus and hepatitis C virus. The only other experimental animal that has been demonstrated to be sensitive to both of these viruses is the chimpanzee, but restrictions on animal testing have meant that experiments using chimpanzees have become almost impossible. Consequently, the development of the tupaia for use as an animal infection model could become a powerful tool for hepatitis virus research and in preclinical studies on drug development.

Tupaia Belangeri as an Experimental Animal Model for Viral Infection

PubMed Central

Tsukiyama-Kohara, Kyoko; Kohara, Michinori

2014-01-01

Tupaias, or tree shrews, are small mammals that are similar in appearance to squirrels. The morphological and behavioral characteristics of the group have been extensively characterized, and despite previously being classified as primates, recent studies have placed the group in its own family, the Tupaiidae. Genomic analysis has revealed that the genus Tupaia is closer to humans than it is to rodents. In addition, tupaias are susceptible to hepatitis B virus and hepatitis C virus. The only other experimental animal that has been demonstrated to be sensitive to both of these viruses is the chimpanzee, but restrictions on animal testing have meant that experiments using chimpanzees have become almost impossible. Consequently, the development of the tupaia for use as an animal infection model could become a powerful tool for hepatitis virus research and in preclinical studies on drug development. PMID:25048261

Experimental study of multichromatic terahertz wave propagation through planar micro-channels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shin, Young-Min -Min; Northern Illinois Univ., Dekalb, IL; Fermi National Accelerator Lab.

2012-04-10

Previous theoretical and numerical studies [Y. M. Shin and L. R. Barnett, Appl. Phys. Lett. 92, 091501 (2008) and Y. M. Shin et al., Appl. Phys. Lett. 93, 221504 (2008)] have reported that a planar micro-channel with an asymmetric corrugation array supports strongly confined propagation of broadband THz plasmonic waves. The highly broad spectral response is experimentally demonstrated in the near-THz regime of 0.19-0.265 THz. Signal reflection and transmission tests on the three designed micro-channels including directional couplers resulted in a full-width-half-maximum bandwidth of ~ 50-60GHz with an insertion loss of approximately -5 dB, which is in good agreement withmore » simulation data. As a result, these micro-structures can be utilized for free electron beam and electronic/optic integrated devices« less

Prediction of perceptual defense from experimental stress and susceptibility to stress as indicated by thematic apperception.

PubMed

Tuma, J M

1975-02-01

The present investigation tested the hypothesis advanced by J. Inglis (1961) that perceptual defense and perceptual vigilance result from an interaction between personality differences and degrees of experimental stress. The design, which controlled for questionable procedures used in previous studies, utilized 32 introverts and 32 extraverts, half male and half female, in an experiment with a visual recognition-task. Results indicated that under low-stress conditions introverts and extraverts identified by their response to a thematic apperception task react to threatening stimuli with perceptual defense and perceptual vigilance, respectively. Under high-stress conditions, type of avoidance activity reverses; extraverts react with perceptual defense and introverts with perceptual vigilance. It was suggested that, when both personality and stress variables are controlled, results of the perceptual defense paradigm are predictable and consistent, in support of Inglis' hypothesis.

Biomechanical responses of PMHS in moderate-speed rear impacts and development of response targets for evaluating the internal and external biofidelity of ATDS.

PubMed

Kang, Yun-Seok; Bolte, John H; Moorhouse, Kevin; Donnelly, Bruce; Herriott, Rodney; Mallory, Ann

2012-10-01

The objectives of this study were to obtain biomechanical responses of post mortem human subjects (PMHS) by subjecting them to two moderate-speed rear impact sled test conditions (8.5g, 17 km/h; 10.5g, 24 km/h) while positioned in an experimental seat system, and to create biomechanical targets for internal and external biofidelity evaluation of rear impact ATDs. The experimental seat was designed to measure external loads on the head restraint (4 load cells), seat back (6 load cells), and seat pan (4 load cells) such that subject dynamic interaction with the seat could be evaluated. This seat system was capable of simulating the dynamic characteristics of modern vehicle seat backs by considering the moment-rotation properties of a typical passenger vehicle, thus providing a more realistic test environment than using a rigid seat with a non-rotating seat back as done in previous studies. Instrumentation used to measure biomechanical responses of the PMHS included both accelerometers and angular rate sensors (ARS). A total of fourteen sled tests using eight PMHS (males 175.8 ± 6.2 cm of stature and 78.4 ± 7.2 kg of weight) provided data sets of seven PMHS for both test conditions. The biomechanical responses are described at both speeds, and cervical spine injuries are documented. Biomechanical targets are also created for internal and external biofidelity evaluation of rear impact anthropomorphic test devices (ATDs).

The Impact of Environmental Design on Doffing Personal Protective Equipment in a Healthcare Environment: A Formative Human Factors Trial.

PubMed

Herlihey, Tracey A; Gelmi, Stefano; Cafazzo, Joseph A; Hall, Trevor N T

2017-06-01

OBJECTIVE To explore the impact of environmental design on doffing personal protective equipment in a simulated healthcare environment. METHODS A mixed-methods approach was used that included human-factors usability testing and qualitative questionnaire responses. A patient room and connecting anteroom were constructed for testing purposes. This experimental doffing area was designed to overcome the environmental failures identified in a previous study and was not constructed based on any generalizable hospital standard. RESULTS In total, 72 healthcare workers from Ontario, Canada, took part in the study and tested the simulated doffing area. The following environmental design changes were tested and were deemed effective: increasing prominence of color-coded zones; securing disinfectant wipes and hand sanitizer; outlining disposal bins locations; providing mirrors to detect possible contamination; providing hand rails to assist with doffing; and restricting the space to doff. Further experimentation and iterative design are required with regard to several important features: positioning the disposal bins for safety, decreasing the risk of contamination and user accessibility; optimal positioning of mirrors for safety; communication within the team; and positioning the secondary team member for optimal awareness. Additional design suggestions also emerged during this study, and they require future investigation. CONCLUSIONS This study highlights the importance of the environment on doffing personal protective equipment in a healthcare setting. Iterative testing and modification of the design of the environment (doffing area) are important to enhancing healthcare worker safety. Infect Control Hosp Epidemiol 2017;38:712-717.

EcAMSat: Effect of Space-Flight on Antibiotic Resistance of a Pathogenic Bacterium and its Genetic Basis

NASA Technical Reports Server (NTRS)

Matin, A. C.; Benoit, M.; Chin. M.; Chinn, T. N.; Cohen, A.; Friedericks, C.; Henschke, M. B.; Keyhan, M.; Lera, M. P.; Padgen, M. R.;

IXV re-entry demonstrator: Mission overview, system challenges and flight reward

NASA Astrophysics Data System (ADS)

Angelini, Roberto; Denaro, Angelo

2016-07-01

The Intermediate eXperimental Vehicle (IXV) is an advanced re-entry demonstrator vehicle aimed to perform in-flight experimentation of atmospheric re-entry enabling systems and technologies. The IXV integrates key technologies at the system level, with significant advancements on Europe's previous flying test-beds. The project builds on previous achievements at system and technology levels, and provides a unique and concrete way of establishing and consolidating Europe's autonomous position in the strategic field of atmospheric re-entry. The IXV mission and system objectives are the design, development, manufacturing, assembling and on-ground to in-flight verification of an autonomous European lifting and aerodynamically controlled reentry system, integrating critical re-entry technologies at system level. Among such critical technologies of interest, special attention is paid to aerodynamic and aerothermodynamics experimentation, including advanced instrumentation for aerothermodynamics phenomena investigations, thermal protections and hot-structures, guidance, navigation and flight control through combined jets and aerodynamic surfaces (i.e. flaps), in particular focusing on the technologies integration at system level for flight. Following the extensive detailed design, manufacturing, qualification, integration and testing of the flight segment and ground segment elements, IXV has performed a full successful flight on February 11th 2015. After the launch with the VEGA launcher form the CSG spaceport in French Guyana, IXV has performed a full nominal mission ending with a successful splashdown in the Pacific Ocean. During Flight Phase, the IXV space and ground segments worked perfectly, implementing the whole flight program in line with the commanded maneuvers and trajectory prediction, performing an overall flight of 34.400 km including 7.600 km with hot atmospheric re-entry in automatic guidance, concluding with successful precision landing at a distance of ~1 km from the target, including the wind drift acting on the parachute from an altitude of 4.5 km.

A Preliminary Investigation on Smokeless Tobacco Use and Its Cognitive Effects Among Athletes

PubMed Central

Zandonai, Thomas; Chiamulera, Cristiano; Mancabelli, Alberto; Falconieri, Danilo; Diana, Marco

2018-01-01

Introduction: Among athletes, an increasing use of nicotine via smokeless tobacco has been reported. However, there are currently unanswered questions about whether the use by athletes is due to nicotine’s addictive properties and/or to benefits in physical and cognitive performance (e.g., decision-making). In this original article we reported about, (i) snus-induced reinforcing effects among snus-user athletes (Survey) and (ii) the effects of snus on the Iowa Gambling Task (IGT) in snus-user skiers (Experimental study). IGT is an experimental neuropsychological task that has been previously used on athletes and addicts to test decision-making. Methods: Survey: data were collected with the modified Cigarette Evaluation Questionnaire (mCEQ) that was administered to 61 winter sport athlete snus-users in Northern Italy. Experimental study: IGT data included: amount of money earned, number of choices from advantageous and disadvantageous decks and overall net score. Eighteen male snus-users were tested under satiety or after 12-h abstinence conditions according to a crossover design. Results: Survey: the comparison between occasional vs. regular snus-users showed a statistically significant difference in satisfaction (P = 0.0088), calm (P = 0.0252), and enjoyment (P = 0.0001) mCEQ items suggesting a snus intake/effect relationship. Experimental study: significantly higher IGT net scores were found during the first 20 choice cards after abstinence vs. satiety conditions (P = 0.0024). Conclusion: In the Survey, regular snus use induces greater satisfaction and psychological reward than occasional use. In the Experimental study, snus intake might produce an early and transient cognitive improvement on IGT in abstinent snus-users, presumably acting as a withdrawal relief. PMID:29593541

The Engineering and Science Issues Test (ESIT): a discipline-specific approach to assessing moral judgment.

PubMed

Borenstein, Jason; Drake, Matthew J; Kirkman, Robert; Swann, Julie L

2010-06-01

To assess ethics pedagogy in science and engineering, we developed a new tool called the Engineering and Science Issues Test (ESIT). ESIT measures moral judgment in a manner similar to the Defining Issues Test, second edition, but is built around technical dilemmas in science and engineering. We used a quasi-experimental approach with pre- and post-tests, and we compared the results to those of a control group with no overt ethics instruction. Our findings are that several (but not all) stand-alone classes showed a significant improvement compared to the control group when the metric includes multiple stages of moral development. We also found that the written test had a higher response rate and sensitivity to pedagogy than the electronic version. We do not find significant differences on pre-test scores with respect to age, education level, gender or political leanings, but we do on whether subjects were native English speakers. We did not find significant differences on pre-test scores based on whether subjects had previous ethics instruction; this could suggest a lack of a long-term effect from the instruction.

The impact of retirement on health: quasi-experimental methods using administrative data.

PubMed

Horner, Elizabeth Mokyr; Cullen, Mark R

2016-02-19

Is retirement good or bad for health? Disentangling causality is difficult. Much of the previous quasi-experimental research on the effect of health on retirement used self-reported health and relied upon discontinuities in public retirement incentives across Europe. The current study investigated the effect of retirement on health by exploiting discontinuities in private retirement incentives to test the effect of retirement on health using a quasi-experimental study design. Secondary data (1997-2009) on a cohort of male manufacturing workers in a United States setting. Health status was determined using claims data from private insurance and Medicare. Analyses used employer-based administrative and claims data and claim data from Medicare. Widely used selection on observables models overstate the negative impact of retirement due to the endogeneity of the decision to retire. In addition, health status as measured by administrative claims data provide some advantages over the more commonly used survey items. Using an instrument and administrative health records, we find null to positive effects from retirement on all fronts, with a possible exception of increased risk for diabetes. This study provides evidence that retirement is not detrimental and may be beneficial to health for a sample of manufacturing workers. In addition, it supports previous research indicating that quasi-experimental methodologies are necessary to evaluate the relationship between retirement and health, as any selection on observable model will overstate the negative relationship of retirement on health. Further, it provides a model for how such research could be implemented in countries like the United States that do not have a strong public pension program. Finally, it demonstrates that such research need-not rely upon survey data, which has certain shortcomings and is not always available for homogenous samples.

A Virtual Out-of-Body Experience Reduces Fear of Death

PubMed Central

2017-01-01

Immersive virtual reality can be used to visually substitute a person’s real body by a life-sized virtual body (VB) that is seen from first person perspective. Using real-time motion capture the VB can be programmed to move synchronously with the real body (visuomotor synchrony), and also virtual objects seen to strike the VB can be felt through corresponding vibrotactile stimulation on the actual body (visuotactile synchrony). This setup typically gives rise to a strong perceptual illusion of ownership over the VB. When the viewpoint is lifted up and out of the VB so that it is seen below this may result in an out-of-body experience (OBE). In a two-factor between-groups experiment with 16 female participants per group we tested how fear of death might be influenced by two different methods for producing an OBE. In an initial embodiment phase where both groups experienced the same multisensory stimuli there was a strong feeling of body ownership. Then the viewpoint was lifted up and behind the VB. In the experimental group once the viewpoint was out of the VB there was no further connection with it (no visuomotor or visuotactile synchrony). In a control condition, although the viewpoint was in the identical place as in the experimental group, visuomotor and visuotactile synchrony continued. While both groups reported high scores on a question about their OBE illusion, the experimental group had a greater feeling of disownership towards the VB below compared to the control group, in line with previous findings. Fear of death in the experimental group was found to be lower than in the control group. This is in line with previous reports that naturally occurring OBEs are often associated with enhanced belief in life after death. PMID:28068368

The perfect family: decision making in biparental care.

PubMed

Akçay, Erol; Roughgarden, Joan

2009-10-13

Previous theoretical work on parental decisions in biparental care has emphasized the role of the conflict between evolutionary interests of parents in these decisions. A prominent prediction from this work is that parents should compensate for decreases in each other's effort, but only partially so. However, experimental tests that manipulate parents and measure their responses fail to confirm this prediction. At the same time, the process of parental decision making has remained unexplored theoretically. We develop a model to address the discrepancy between experiments and the theoretical prediction, and explore how assuming different decision making processes changes the prediction from the theory. We assume that parents make decisions in behavioral time. They have a fixed time budget, and allocate it between two parental tasks: provisioning the offspring and defending the nest. The proximate determinant of the allocation decisions are parents' behavioral objectives. We assume both parents aim to maximize the offspring production from the nest. Experimental manipulations change the shape of the nest production function. We consider two different scenarios for how parents make decisions: one where parents communicate with each other and act together (the perfect family), and one where they do not communicate, and act independently (the almost perfect family). The perfect family model is able to generate all the types of responses seen in experimental studies. The kind of response predicted depends on the nest production function, i.e. how parents' allocations affect offspring production, and the type of experimental manipulation. In particular, we find that complementarity of parents' allocations promotes matching responses. In contrast, the relative responses do not depend on the type of manipulation in the almost perfect family model. These results highlight the importance of the interaction between nest production function and how parents make decisions, factors that have largely been overlooked in previous models.

Intrinsic motivation and attentional capture from gamelike features in a visual search task.

PubMed

Miranda, Andrew T; Palmer, Evan M

2014-03-01

In psychology research studies, the goals of the experimenter and the goals of the participants often do not align. Researchers are interested in having participants who take the experimental task seriously, whereas participants are interested in earning their incentive (e.g., money or course credit) as quickly as possible. Creating experimental methods that are pleasant for participants and that reward them for effortful and accurate data generation, while not compromising the scientific integrity of the experiment, would benefit both experimenters and participants alike. Here, we explored a gamelike system of points and sound effects that rewarded participants for fast and accurate responses. We measured participant engagement at both cognitive and perceptual levels and found that the point system (which invoked subtle, anonymous social competition between participants) led to positive intrinsic motivation, while the sound effects (which were pleasant and arousing) led to attentional capture for rewarded colors. In a visual search task, points were awarded after each trial for fast and accurate responses, accompanied by short, pleasant sound effects. We adapted a paradigm from Anderson, Laurent, and Yantis (Proceedings of the National Academy of Sciences 108(25):10367-10371, 2011b), in which participants completed a training phase during which red and green targets were probabilistically associated with reward (a point bonus multiplier). During a test phase, no points or sounds were delivered, color was irrelevant to the task, and previously rewarded targets were sometimes presented as distractors. Significantly longer response times on trials in which previously rewarded colors were present demonstrated attentional capture, and positive responses to a five-question intrinsic-motivation scale demonstrated participant engagement.