Communications network design and costing model users manual

NASA Technical Reports Server (NTRS)

Logan, K. P.; Somes, S. S.; Clark, C. A.

1983-01-01

The information and procedures needed to exercise the communications network design and costing model for performing network analysis are presented. Specific procedures are included for executing the model on the NASA Lewis Research Center IBM 3033 computer. The concepts, functions, and data bases relating to the model are described. Model parameters and their format specifications for running the model are detailed.

JSC Design and Procedural Standards, JSC-STD-8080

NASA Technical Reports Server (NTRS)

Punch, Danny T.

2011-01-01

This document provides design and procedural requirements appropriate for inclusion in specifications for any human spaceflight program, project, spacecraft, system, or end item. The term "spacecraft" as used in the standards includes launch vehicles, orbital vehicles, non-terrestrial surface vehicles, and modules. The standards are developed and maintained as directed by Johnson Space Center (JSC) Policy Directive JPD 8080.2, JSC Design and Procedural Standards for Human Space Flight Equipment. The Design and Procedural Standards contained in this manual represent human spacecraft design and operational knowledge applicable to a wide range of spaceflight activities. These standards are imposed on JSC human spaceflight equipment through JPD 8080.2. Designers shall comply with all design standards applicable to their design effort.

A contribution to the design specification of single-cell multi-resonant converters

NASA Astrophysics Data System (ADS)

Franck, F.; Schroeder, D.

The state plane technique is used to develop a design-specification procedure that enables the designer to directly calculate the stresses on all elements of the different topologies for quasi-resonant converters. If parasitic elements are considered, multiresonant topologies are obtained. These topologies can be calculated for the design specification if the procedure for quasi-resonant topologies is adapted to this situation. A novel theoretical approach for describing the internal behavior of multiresonant converters and for visualizing the switching conditions and the points of maximum component stresses is proposed. The multiresonant switching technique combines two advantages: the lossless snubbing of both the transistor and the diode is achieved by only three reactive elements, and a controllable no-load operation is possible. This analysis procedure is well suited for calculating dc-dc converter with an output power up to several hundred watts.

46 CFR 160.132-23 - Procedure for approval of design or material change.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Procedure for approval of design or material change. 160.132-23 Section 160.132-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Launching Appliances-Davits § 160.132-23 Procedure for approval of...

46 CFR 160.132-23 - Procedure for approval of design or material change.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Procedure for approval of design or material change. 160.132-23 Section 160.132-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Launching Appliances-Davits § 160.132-23 Procedure for approval of...

46 CFR 160.135-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Procedure for approval of design, material, or construction change. 160.135-23 Section 160.135-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Lifeboats § 160.135-23 Procedure for approval of...

46 CFR 160.077-7 - Procedure for approval of design or material revision.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Procedure for approval of design or material revision. 160.077-7 Section 160.077-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Hybrid Inflatable Personal Flotation Devices § 160.077-7 Procedure...

46 CFR 160.077-7 - Procedure for approval of design or material revision.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Procedure for approval of design or material revision. 160.077-7 Section 160.077-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Hybrid Inflatable Personal Flotation Devices § 160.077-7 Procedure...

46 CFR 160.077-7 - Procedure for approval of design or material revision.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Procedure for approval of design or material revision. 160.077-7 Section 160.077-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Hybrid Inflatable Personal Flotation Devices § 160.077-7 Procedure...

46 CFR 160.115-23 - Procedure for approval of design or material change.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Procedure for approval of design or material change. 160.115-23 Section 160.115-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Launching Appliances-Winches § 160.115-23 Procedure for approval of...

46 CFR 160.115-23 - Procedure for approval of design or material change.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Procedure for approval of design or material change. 160.115-23 Section 160.115-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Launching Appliances-Winches § 160.115-23 Procedure for approval of...

46 CFR 160.135-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Procedure for approval of design, material, or construction change. 160.135-23 Section 160.135-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Lifeboats (SOLAS) § 160.135-23 Procedure for approva...

48 CFR 24.103 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... work statement specifically identifies the system of records on individuals and the design, development, or operation work to be performed; and (2) Make available, in accordance with agency procedures... contracting officer shall review requirements to determine whether the contract will involve the design...

40 CFR Appendix A to Part 75 - Specifications and Test Procedures

Code of Federal Regulations, 2012 CFR

2012-07-01

... appendix. RE = Expected average design removal efficiency of control equipment (%). 2.1.1.3Span Value(s... 40 Protection of Environment 17 2012-07-01 2012-07-01 false Specifications and Test Procedures A... (CONTINUED) CONTINUOUS EMISSION MONITORING Pt. 75, App. A Appendix A to Part 75—Specifications and Test...

40 CFR Appendix A to Part 75 - Specifications and Test Procedures

Code of Federal Regulations, 2013 CFR

2013-07-01

... appendix. RE = Expected average design removal efficiency of control equipment (%). 2.1.1.3Span Value(s... 40 Protection of Environment 17 2013-07-01 2013-07-01 false Specifications and Test Procedures A... (CONTINUED) CONTINUOUS EMISSION MONITORING Pt. 75, App. A Appendix A to Part 75—Specifications and Test...

Integrated flight/propulsion control system design based on a decentralized, hierarchical approach

NASA Technical Reports Server (NTRS)

Mattern, Duane; Garg, Sanjay; Bullard, Randy

1989-01-01

A sample integrated flight/propulsion control system design is presented for the piloted longitudinal landing task with a modern, statistically unstable fighter aircraft. The design procedure is summarized. The vehicle model used in the sample study is described, and the procedure for partitioning the integrated system is presented along with a description of the subsystems. The high-level airframe performance specifications and control design are presented and the control performance is evaluated. The generation of the low-level (engine) subsystem specifications from the airframe requirements are discussed, and the engine performance specifications are presented along with the subsystem control design. A compensator to accommodate the influence of airframe outputs on the engine subsystem is also considered. Finally, the entire closed loop system performance and stability characteristics are examined.

Integrated flight/propulsion control system design based on a decentralized, hierarchical approach

NASA Technical Reports Server (NTRS)

Mattern, Duane; Garg, Sanjay; Bullard, Randy

1989-01-01

A sample integrated flight/propulsion control system design is presented for the piloted longitiudinal landing task with a modern, statistically unstable fighter aircraft. The design procedure is summarized, the vehicle model used in the sample study is described, and the procedure for partitioning the integrated system is presented along with a description of the subsystems. The high-level airframe performance specifications and control design are presented and the control performance is evaluated. The generation of the low-level (engine) subsystem specifications from the airframe requirements are discussed, and the engine performance specifications are presented along with the subsystem control design. A compensator to accommodate the influence of airframe outputs on the engine subsystem is also considered. Finally, the entire closed loop system performance and stability characteristics are examined.

Standard operating procedures, water immersion facility, revision B

NASA Technical Reports Server (NTRS)

1979-01-01

General guideline procedures to identify those factors that are common to all spacecraft design laboratory support group emergency procedures and to establish the basic rescue plan are presented. This eliminates needless repetition of the fundamentals from the other, more specific procedures.

7 CFR 1724.53 - Preparation of plans and specifications.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Preparation of plans and specifications. 1724.53... PROCEDURES Electric System Design § 1724.53 Preparation of plans and specifications. The provisions of this...) Transmission lines. Specifications and drawings, transmission line design data manual, vicinity maps of the...

46 CFR 164.019-9 - Procedure for acceptance of revisions of design, process, or materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Procedure for acceptance of revisions of design, process, or materials. 164.019-9 Section 164.019-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL MATERIALS Personal Flotation Device Components § 164.019-9 Procedure fo...

46 CFR 164.019-9 - Procedure for acceptance of revisions of design, process, or materials.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Procedure for acceptance of revisions of design, process, or materials. 164.019-9 Section 164.019-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL MATERIALS Personal Flotation Device Components § 164.019-9 Procedure fo...

46 CFR 164.019-9 - Procedure for acceptance of revisions of design, process, or materials.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Procedure for acceptance of revisions of design, process, or materials. 164.019-9 Section 164.019-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL MATERIALS Personal Flotation Device Components § 164.019-9 Procedure fo...

40 CFR Appendix A to Part 75 - Specifications and Test Procedures

Code of Federal Regulations, 2011 CFR

2011-07-01

...-1b in section 2.1.1.1 of this appendix. RE = Expected average design removal efficiency of control... 40 Protection of Environment 16 2011-07-01 2011-07-01 false Specifications and Test Procedures A... (CONTINUED) CONTINUOUS EMISSION MONITORING Pt. 75, App. A Appendix A to Part 75—Specifications and Test...

48 CFR 36.601-3 - Applicable contracting procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Services 36.601-3 Applicable contracting procedures. (a)(1) For facility design contracts, the statement of work shall require that the architect-engineer specify, in the construction design specifications, use..., availability, price reasonableness, and cost-effectiveness. Where appropriate, the statement of work also shall...

21 CFR 814.39 - PMA supplements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... sterilization procedures. (5) Changes in packaging. (6) Changes in the performance or design specifications, circuits, components, ingredients, principle of operation, or physical layout of the device. (7) Extension... the performance or design specifications, circuits, components, ingredients, principles of operation...

Revisiting the Concepts "Approach", "Design" and "Procedure" According to the Richards and Rodgers (2011) Framework

ERIC Educational Resources Information Center

Cumming, Brett

2012-01-01

The three concepts Approach, Design and Procedure as proposed in Rodgers' Framework are considered particularly effective as a framework in second language teaching with the specific aim of developing communication as well as for better understanding methodology in the use of communicative language use.

Application of the QSDC procedure to the formulation of space shuttle design criteria. Volume 2: Applications guide

NASA Technical Reports Server (NTRS)

Bouton, I.; Martin, G. L.

1972-01-01

Criteria to determine the probability of aircraft structural failure were established according to the Quantitative Structural Design Criteria by Statistical Methods, the QSDC Procedure. This criteria method was applied to the design of the space shuttle during this contract. An Applications Guide was developed to demonstrate the utilization of the QSDC Procedure, with examples of the application to a hypothetical space shuttle illustrating the application to specific design problems. Discussions of the basic parameters of the QSDC Procedure: the Limit and Omega Conditions, and the strength scatter, have been included. Available data pertinent to the estimation of the strength scatter have also been included.

Dimming LEDs with Phase-Cut Dimmers: The Specifier's Process for Maximizing Success

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, Naomi J.; Poplawski, Michael E.

2013-10-01

This report reviews how phase-cut dimmers work, how LEDs differ from the incandescent lamps that the dimmers were historically designed to control, and how these differences can lead to complications when trying to dim LEDs. Compatibility between a specific LED source and a specific phase-cut dimmer is often unknown and difficult to assess, and ensuring compatibility adds complexity to the design, specification, bidding, and construction observation phases for new buildings and major remodel projects. To maximize project success, this report provides both general guidance and step-by-step procedures for designing phase-controlled LED dimming on both new and existing projects, as wellmore » as real-world examples of how to use those procedures.« less

40 CFR 53.51 - Demonstration of compliance with design specifications and manufacturing and test requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... compliance with design specifications and manufacturing and test requirements. (a) Overview. (1) Paragraphs... document its post-manufacturing test procedures. As a minimum, each test shall consist of the following... 40 Protection of Environment 5 2011-07-01 2011-07-01 false Demonstration of compliance with design...

40 CFR 53.51 - Demonstration of compliance with design specifications and manufacturing and test requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... compliance with design specifications and manufacturing and test requirements. (a) Overview. (1) Paragraphs... document its post-manufacturing test procedures. As a minimum, each test shall consist of the following... 40 Protection of Environment 6 2014-07-01 2014-07-01 false Demonstration of compliance with design...

40 CFR 53.51 - Demonstration of compliance with design specifications and manufacturing and test requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... compliance with design specifications and manufacturing and test requirements. (a) Overview. (1) Paragraphs... document its post-manufacturing test procedures. As a minimum, each test shall consist of the following... 40 Protection of Environment 6 2013-07-01 2013-07-01 false Demonstration of compliance with design...

40 CFR 53.51 - Demonstration of compliance with design specifications and manufacturing and test requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... compliance with design specifications and manufacturing and test requirements. (a) Overview. (1) Paragraphs... document its post-manufacturing test procedures. As a minimum, each test shall consist of the following... 40 Protection of Environment 6 2012-07-01 2012-07-01 false Demonstration of compliance with design...

46 CFR 160.170-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Procedure for approval of design, material, or construction change. 160.170-23 Section 160.170-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Davit-Launched Liferaft Automatic Release Hooks ...

46 CFR 160.170-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Procedure for approval of design, material, or construction change. 160.170-23 Section 160.170-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Davit-Launched Liferaft Automatic Release Hooks ...

Representative sets of design hydrographs for ungauged catchments: A regional approach using probabilistic region memberships

NASA Astrophysics Data System (ADS)

Brunner, Manuela Irene; Seibert, Jan; Favre, Anne-Catherine

2018-02-01

Traditional design flood estimation approaches have focused on peak discharges and have often neglected other hydrograph characteristics such as hydrograph volume and shape. Synthetic design hydrograph estimation procedures overcome this deficiency by jointly considering peak discharge, hydrograph volume, and shape. Such procedures have recently been extended to allow for the consideration of process variability within a catchment by a flood-type specific construction of design hydrographs. However, they depend on observed runoff time series and are not directly applicable in ungauged catchments where such series are not available. To obtain reliable flood estimates, there is a need for an approach that allows for the consideration of process variability in the construction of synthetic design hydrographs in ungauged catchments. In this study, we therefore propose an approach that combines a bivariate index flood approach with event-type specific synthetic design hydrograph construction. First, regions of similar flood reactivity are delineated and a classification rule that enables the assignment of ungauged catchments to one of these reactivity regions is established. Second, event-type specific synthetic design hydrographs are constructed using the pooled data divided by event type from the corresponding reactivity region in a bivariate index flood procedure. The approach was tested and validated on a dataset of 163 Swiss catchments. The results indicated that 1) random forest is a suitable classification model for the assignment of an ungauged catchment to one of the reactivity regions, 2) the combination of a bivariate index flood approach and event-type specific synthetic design hydrograph construction enables the consideration of event types in ungauged catchments, and 3) the use of probabilistic class memberships in regional synthetic design hydrograph construction helps to alleviate the problem of misclassification. Event-type specific synthetic design hydrograph sets enable the inclusion of process variability into design flood estimation and can be used as a compromise between single best estimate synthetic design hydrographs and continuous simulation studies.

Project W-314 specific test and evaluation plan for transfer line SN-633 (241-AX-B to 241-AY-02A)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hays, W.H.

1998-03-20

The purpose of this Specific Test and Evaluation Plan (STEP) is to provide a detailed written plan for the systematic testing of modifications made by the addition of the SN-633 transfer line by the W-314 Project. The STEP develops the outline for test procedures that verify the system`s performance to the established Project design criteria. The STEP is a lower tier document based on the W-314 Test and Evaluation Plan (TEP). This STEP encompasses all testing activities required to demonstrate compliance to the project design criteria as it relates to the addition of transfer line SN-633. The Project Design Specificationsmore » (PDS) identify the specific testing activities required for the Project. Testing includes Validations and Verifications (e.g., Commercial Grade Item Dedication activities), Factory Acceptance Tests (FATs), installation tests and inspections, Construction Acceptance Tests (CATs), Acceptance Test Procedures (ATPs), Pre-Operational Test Procedures (POTPs), and Operational Test Procedures (OTPs). It should be noted that POTPs are not required for testing of the transfer line addition. The STEP will be utilized in conjunction with the TEP for verification and validation.« less

Small Optics Laser Damage Test Procedure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wolfe, Justin

2017-10-19

This specification defines the requirements and procedure for laser damage testing of coatings and bare surfaces designated for small optics in the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory (LLNL).

7 CFR 1724.53 - Preparation of plans and specifications.

Code of Federal Regulations, 2011 CFR

2011-01-01

... SERVICE, DEPARTMENT OF AGRICULTURE ELECTRIC ENGINEERING, ARCHITECTURAL SERVICES AND DESIGN POLICIES AND PROCEDURES Electric System Design § 1724.53 Preparation of plans and specifications. The provisions of this section apply to all borrower electric system facilities regardless of the source of financing. (a...

7 CFR 1724.53 - Preparation of plans and specifications.

Code of Federal Regulations, 2012 CFR

2012-01-01

... SERVICE, DEPARTMENT OF AGRICULTURE ELECTRIC ENGINEERING, ARCHITECTURAL SERVICES AND DESIGN POLICIES AND PROCEDURES Electric System Design § 1724.53 Preparation of plans and specifications. The provisions of this section apply to all borrower electric system facilities regardless of the source of financing. (a...

7 CFR 1724.53 - Preparation of plans and specifications.

Code of Federal Regulations, 2014 CFR

2014-01-01

... SERVICE, DEPARTMENT OF AGRICULTURE ELECTRIC ENGINEERING, ARCHITECTURAL SERVICES AND DESIGN POLICIES AND PROCEDURES Electric System Design § 1724.53 Preparation of plans and specifications. The provisions of this section apply to all borrower electric system facilities regardless of the source of financing. (a...

7 CFR 1724.53 - Preparation of plans and specifications.

Code of Federal Regulations, 2013 CFR

2013-01-01

... SERVICE, DEPARTMENT OF AGRICULTURE ELECTRIC ENGINEERING, ARCHITECTURAL SERVICES AND DESIGN POLICIES AND PROCEDURES Electric System Design § 1724.53 Preparation of plans and specifications. The provisions of this section apply to all borrower electric system facilities regardless of the source of financing. (a...

SUPPORTING THE INDUSTRY BY DEVELOPING A DESIGN GUIDANCE FOR COMPUTER-BASED PROCEDURES FOR FIELD WORKERS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oxstrand, Johanna; LeBlanc, Katya

The paper-based procedures currently used for nearly all activities in the commercial nuclear power industry have a long history of ensuring safe operation of the plants. However, there is potential to greatly increase efficiency and safety by improving how the human interacts with the procedures, which can be achieved through the use of computer-based procedures (CBPs). A CBP system offers a vast variety of improvements, such as context driven job aids, integrated human performance tools and dynamic step presentation. As a step toward the goal of improving procedure use performance, the U.S. Department of Energy Light Water Reactor Sustainability Programmore » researchers, together with the nuclear industry, have been investigating the possibility and feasibility of replacing current paper-based procedures with CBPs. The main purpose of the CBP research conducted at the Idaho National Laboratory was to provide design guidance to the nuclear industry to be used by both utilities and vendors. After studying existing design guidance for CBP systems, the researchers concluded that the majority of the existing guidance is intended for control room CBP systems, and does not necessarily address the challenges of designing CBP systems for instructions carried out in the field. Further, the guidance is often presented on a high level, which leaves the designer to interpret what is meant by the guidance and how to specifically implement it. The authors developed a design guidance to provide guidance specifically tailored to instructions that are carried out in the field based.« less

A haptic interface for virtual simulation of endoscopic surgery.

PubMed

Rosenberg, L B; Stredney, D

1996-01-01

Virtual reality can be described as a convincingly realistic and naturally interactive simulation in which the user is given a first person illusion of being immersed within a computer generated environment While virtual reality systems offer great potential to reduce the cost and increase the quality of medical training, many technical challenges must be overcome before such simulation platforms offer effective alternatives to more traditional training means. A primary challenge in developing effective virtual reality systems is designing the human interface hardware which allows rich sensory information to be presented to users in natural ways. When simulating a given manual procedure, task specific human interface requirements dictate task specific human interface hardware. The following paper explores the design of human interface hardware that satisfies the task specific requirements of virtual reality simulation of Endoscopic surgical procedures. Design parameters were derived through direct cadaver studies and interviews with surgeons. Final hardware design is presented.

Screening and Diagnostic Procedure for Identification of Adult Learning Problems. 309 Demonstration Project.

ERIC Educational Resources Information Center

International Labour Office, Islamabad (Pakistan). Asian and Pacific Skill Development Programme.

This screening and diagnostic procedure is intended to identify Level 1 adults with specific learning problems. The adults not meeting criteria on the assessments for visual and auditory functions should be referred to proper medical services for full evaluations. A prescriptive teaching program should be specifically designed to meet needs of…

40 CFR 1065.901 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

....901 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Field Testing and Portable Emission Measurement Systems § 1065.901...-specific emissions using portable emission measurement systems (PEMS). These procedures are designed...

Interim Procedures Safeguarding Mobile Devices during International Travel

EPA Pesticide Factsheets

This procedure is for safeguarding EPA information and systems for all employees, contractors, and other users while on international travel or to specifically designated locations within the United States and foreign embassies.

Design and installation package for a solar powered pump

NASA Technical Reports Server (NTRS)

1978-01-01

The design and installation procedures of a solar powered pump developed by Calmac Manufacturing Company are presented. Subsystem installation, operation and maintenance requirements, subsystem performance specifications, and detailed design drawings are included.

An Assessment Program Designed To Improve Communication Instruction through a Competency-Based Core Curriculum.

ERIC Educational Resources Information Center

Aitken, Joan E.; Neer, Michael R.

This paper provides an example procedure used to design and install a program of assessment to improve communication instruction through a competency-based core curriculum at a mid-sized, urban university. The paper models the various steps in the process, and includes specific tests, forms, memos, course description, sources, and procedures which…

AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT XIII, BATTERY SERVICE AND TESTING PROCEDURES--PART II.

ERIC Educational Resources Information Center

Human Engineering Inst., Cleveland, OH.

THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO FAMILIARIZE THE TRAINEE WITH PROCEDURES FOR SERVICING LEAD-ACID STORAGE BATTERIES USED ON DIESEL POWERED EQUIPMENT. TOPICS ARE (1) ELECTROLYTE AND SPECIFIC GRAVITY, (2) BATTERY CHARGING, (3) STORAGE BATTERY TYPES AND DESIGN, (4) BATTERY CAPACITY RATINGS, (5) BATTERY INSTALLATION, SERVICING, AND…

46 CFR 160.133-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Procedure for approval of design, material, or construction change. 160.133-23 Section 160.133-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Release Mechanisms for Lifeboats and Rescue Boats §...

46 CFR 160.133-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Procedure for approval of design, material, or construction change. 160.133-23 Section 160.133-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Release Mechanisms for Lifeboats and Rescue Boats ...

46 CFR 160.156-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Procedure for approval of design, material, or construction change. 160.156-23 Section 160.156-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Rescue Boats and Fast Rescue Boats (SOLAS) § 160.156...

46 CFR 160.156-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Procedure for approval of design, material, or construction change. 160.156-23 Section 160.156-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Rescue Boats and Fast Rescue Boats (SOLAS) § 160.156...

Determination of photovoltaic concentrator optical design specifications using performance modeling

NASA Astrophysics Data System (ADS)

Kerschen, Kevin A.; Levy, Sheldon L.

The strategy used to develop an optical design specification for a 500X concentration photovoltaic module to be used with a 28-percent-efficient concentrator photovoltaic cell is reported. The computer modeling code (PVOPTICS) developed for this purpose, a Fresnel lens design strategy, and optical component specification procedures are described. Comparisons are made between the predicted performance and the measured performance of components fabricated to those specifications. An acrylic lens and a reflective secondary optical element have been tested, showing efficiencies exceeding 88 percent.

The Effectiveness of Two Grammar Treatment Procedures for Children with SLI: A Randomized Clinical Trial

ERIC Educational Resources Information Center

Smith-Lock, Karen M.; Leitão, Suze; Prior, Polly; Nickels, Lyndsey

2015-01-01

Purpose: This study compared the effectiveness of two grammar treatment procedures for children with specific language impairment. Method: A double-blind superiority trial with cluster randomization was used to compare a cueing procedure, designed to elicit a correct production following an initial error, to a recasting procedure, which required…

Step by Step: Biology Undergraduates’ Problem-Solving Procedures during Multiple-Choice Assessment

PubMed Central

Prevost, Luanna B.; Lemons, Paula P.

2016-01-01

This study uses the theoretical framework of domain-specific problem solving to explore the procedures students use to solve multiple-choice problems about biology concepts. We designed several multiple-choice problems and administered them on four exams. We trained students to produce written descriptions of how they solved the problem, and this allowed us to systematically investigate their problem-solving procedures. We identified a range of procedures and organized them as domain general, domain specific, or hybrid. We also identified domain-general and domain-specific errors made by students during problem solving. We found that students use domain-general and hybrid procedures more frequently when solving lower-order problems than higher-order problems, while they use domain-specific procedures more frequently when solving higher-order problems. Additionally, the more domain-specific procedures students used, the higher the likelihood that they would answer the problem correctly, up to five procedures. However, if students used just one domain-general procedure, they were as likely to answer the problem correctly as if they had used two to five domain-general procedures. Our findings provide a categorization scheme and framework for additional research on biology problem solving and suggest several important implications for researchers and instructors. PMID:27909021

Proceedings: 1990 EPRI gas turbine procurement seminar

DOE Office of Scientific and Technical Information (OSTI.GOV)

McDonald, B.L.; Miller, M.N.

1991-06-01

This seminar presents information that enables utilities to implement more cost-effective procurements for gas turbine and combined-cycle power generation equipment. A systematic approach to specification and permitting procedures can lower unit life-cycle cost. APPROACH. Thirty-two staff members from 25 utilities met in Danvers, Massachusetts, October 9--11, 1990. Speakers representing utilities, vendors, and EPRI contractors presented material on recent procurement and startup experiences, permitting considerations, specification strategy, bid evaluation techniques, and a vendor's perspective of utility procurements. KEY POINTS. The seminar focused on specification features, procurement procedures, and bid evaluation techniques designed to implement life-cycle cost-effective procurement consistent with the plantmore » mission. Speakers highlighted the following issues: Experiential case histories of recent procurements and startups, emphasizing how to design procurement procedures that improve plant operating economics; Current trends in permitting for NO{sub x} compliance and recent permitting experience; Quantifiable evaluations of vendors' bids for RAM-related characteristics; The means to obtain specifically desired but nonstandard equipment features.« less

Three-dimensional aerodynamic shape optimization of supersonic delta wings

NASA Technical Reports Server (NTRS)

Burgreen, Greg W.; Baysal, Oktay

1994-01-01

A recently developed three-dimensional aerodynamic shape optimization procedure AeSOP(sub 3D) is described. This procedure incorporates some of the most promising concepts from the area of computational aerodynamic analysis and design, specifically, discrete sensitivity analysis, a fully implicit 3D Computational Fluid Dynamics (CFD) methodology, and 3D Bezier-Bernstein surface parameterizations. The new procedure is demonstrated in the preliminary design of supersonic delta wings. Starting from a symmetric clipped delta wing geometry, a Mach 1.62 asymmetric delta wing and two Mach 1. 5 cranked delta wings were designed subject to various aerodynamic and geometric constraints.

Statistical methodology for the analysis of dye-switch microarray experiments

PubMed Central

Mary-Huard, Tristan; Aubert, Julie; Mansouri-Attia, Nadera; Sandra, Olivier; Daudin, Jean-Jacques

2008-01-01

Background In individually dye-balanced microarray designs, each biological sample is hybridized on two different slides, once with Cy3 and once with Cy5. While this strategy ensures an automatic correction of the gene-specific labelling bias, it also induces dependencies between log-ratio measurements that must be taken into account in the statistical analysis. Results We present two original statistical procedures for the statistical analysis of individually balanced designs. These procedures are compared with the usual ML and REML mixed model procedures proposed in most statistical toolboxes, on both simulated and real data. Conclusion The UP procedure we propose as an alternative to usual mixed model procedures is more efficient and significantly faster to compute. This result provides some useful guidelines for the analysis of complex designs. PMID:18271965

An iterative requirements specification procedure for decision support systems.

PubMed

Brookes, C H

1987-08-01

Requirements specification is a key element in a DSS development project because it not only determines what is to be done, it also drives the evolution process. A procedure for requirements elicitation is described that is based on the decomposition of the DSS design task into a number of functions, subfunctions, and operators. It is postulated that the procedure facilitates the building of a DSS that is complete and integrates MIS, modelling and expert system components. Some examples given are drawn from the health administration field.

Recollection Training and Transfer Effects in Alzheimer's Disease: Effectiveness of the Repetition-Lag Procedure

ERIC Educational Resources Information Center

Boller, Benjamin; Jennings, Janine M.; Dieudonne, Benedicte; Verny, Marc; Ergis, Anne-Marie

2012-01-01

Objective: This study was designed to extend the use of a memory training technique, known as the repetition-lag procedure, to Alzheimer patients. The specificity of this procedure is to target the process of recollection for improvement. Method: A group of 12 patients were trained individually for 6 h. The training procedure consisted of a series…

40 CFR 35.2005 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... economic investigations or studies, surveys, designs, plans, working drawings, specifications, procedures... design-type projects within the scope of the practice of architecture or professional engineering as... as designed. (10) Collector sewer. The common lateral sewers, within a publicly owned treatment...

40 CFR 35.2005 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... economic investigations or studies, surveys, designs, plans, working drawings, specifications, procedures... design-type projects within the scope of the practice of architecture or professional engineering as... as designed. (10) Collector sewer. The common lateral sewers, within a publicly owned treatment...

Human Factors Considerations for Performance-Based Navigation

NASA Technical Reports Server (NTRS)

Barhydt, Richard; Adams, Catherine A.

2006-01-01

A transition toward a performance-based navigation system is currently underway in both the United States and around the world. Performance-based navigation incorporates Area Navigation (RNAV) and Required Navigation Performance (RNP) procedures that do not rely on the location of ground-based navigation aids. These procedures offer significant benefits to both operators and air traffic managers. Under sponsorship from the Federal Aviation Administration (FAA), the National Aeronautics and Space Administration (NASA) has undertaken a project to document human factors issues that have emerged during RNAV and RNP operations and propose areas for further consideration. Issues were found to include aspects of air traffic control and airline procedures, aircraft systems, and procedure design. Major findings suggest the need for human factors-specific instrument procedure design guidelines. Ongoing industry and government activities to address air-ground communication terminology, procedure design improvements, and chart-database commonality are strongly encouraged.

Permanent-plot procedures for silvicultural and yield research.

Treesearch

Robert O. Curtis; David D. Marshall

2005-01-01

This paper reviews purposes and procedures for establishing and maintaining permanent plots for silvicultural and yield research, sampling and plot design, common errors, and procedures for measuring and recording data. It is a revision and update of a 1983 publication. Although some details are specific to coastal Pacific Northwest conditions, most of the material is...

Human Factors Considerations for Area Navigation Departure and Arrival Procedures

NASA Technical Reports Server (NTRS)

Barhydt, Richard; Adams, Catherine A.

2006-01-01

Area navigation (RNAV) procedures are being implemented in the United States and around the world as part of a transition to a performance-based navigation system. These procedures are providing significant benefits and have also caused some human factors issues to emerge. Under sponsorship from the Federal Aviation Administration (FAA), the National Aeronautics and Space Administration (NASA) has undertaken a project to document RNAV-related human factors issues and propose areas for further consideration. The component focusing on RNAV Departure and Arrival Procedures involved discussions with expert users, a literature review, and a focused review of the NASA Aviation Safety Reporting System (ASRS) database. Issues were found to include aspects of air traffic control and airline procedures, aircraft systems, and procedure design. Major findings suggest the need for specific instrument procedure design guidelines that consider the effects of human performance. Ongoing industry and government activities to address air-ground communication terminology, design improvements, and chart-database commonality are strongly encouraged. A review of factors contributing to RNAV in-service errors would likely lead to improved system design and operational performance.

Bubble formation in microgravity

NASA Technical Reports Server (NTRS)

Antar, Basil N.

1996-01-01

An extensive experimental program was initiated for the purpose of understanding the mechanisms leading to bubble generation during fluid handling procedures in a microgravity environment. Several key fluid handling procedures typical for PCG experiments were identified for analysis in that program. Experiments were designed to specifically understand how such procedures can lead to bubble formation. The experiments were then conducted aboard the NASA KC-135 aircraft which is capable of simulating a low gravity environment by executing a parabolic flight attitude. However, such a flight attitude can only provide a low gravity environment of approximately 10-2go for a maximum period of 30 seconds. Thus all of the tests conducted for these experiments were designed to last no longer than 20 seconds. Several experiments were designed to simulate some of the more relevant fluid handling procedures during protein crystal growth experiments. These include submerged liquid jet cavitation, filling of a cubical vessel, submerged surface scratch, attached drop growth, liquid jet impingement, and geysering experiments. To date, four separate KC-135 flight campaigns were undertaken specifically for performing these experiments. However, different experiments were performed on different flights.

Preliminary vibration, acoustic, and shock design and test criteria for components on the Lightweight External Tank (LWT)

NASA Technical Reports Server (NTRS)

1981-01-01

The Space Shuttle LWT is divided into zones and subzones. Zones are designated primarily to assist in determining the applicable specifications. A subzone (general Specification) is available for use when the location of the component is known but component design and weight are not well defined. When the location, weight, and mounting configuration of the component are known, specifications for appropriate subzone weight ranges are available. Along with the specifications are vibration, acoustic, shock, transportation, handling, and acceptance test requirements and procedures. A method of selecting applicable vibration, acoustic, and shock specifications is presented.

40 CFR 1042.140 - Maximum engine power, displacement, power density, and maximum in-use engine speed.

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE... procedures of 40 CFR part 1065, based on the manufacturer's design and production specifications for the... swept volume from the design specifications for the cylinders using enough significant figures to allow...

40 CFR 1042.140 - Maximum engine power, displacement, power density, and maximum in-use engine speed.

Code of Federal Regulations, 2010 CFR

2010-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE... procedures of 40 CFR part 1065, based on the manufacturer's design and production specifications for the... swept volume from the design specifications for the cylinders using enough significant figures to allow...

40 CFR 1042.140 - Maximum engine power, displacement, power density, and maximum in-use engine speed.

Code of Federal Regulations, 2014 CFR

2014-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE... procedures of 40 CFR part 1065, based on the manufacturer's design and production specifications for the... swept volume from the design specifications for the cylinders using enough significant figures to allow...

Labor Market Identification Model; Procedure in Labor Market Planning for Vocational Education Programs of Columbia Junior College.

ERIC Educational Resources Information Center

Columbia Junior Coll., CA.

This document is designed as a workbook for those planning to conduct labor market surveys. The data gathering procedures were specifically designed for a small rural college with limited financial and manpower resources. The purposes of such a survey are to identify manpower needs, to make the college known as a source of trained manpower, and to…

Training apartment upkeep skills to rehabilitation clients: a comparison of task analytic strategies.

PubMed Central

Williams, G E; Cuvo, A J

1986-01-01

The research was designed to validate procedures to teach apartment upkeep skills to severely handicapped clients with various categorical disabilities. Methodological features of this research included performance comparisons between general and specific task analyses, effect of an impasse correction baseline procedure, social validation of training goals, natural environment assessments and contingencies, as well as long-term follow-up. Subjects were taught to perform upkeep responses on their air conditioner-heating unit, electric range, refrigerator, and electrical appliances within the context of a multiple-probe across subjects experimental design. The results showed acquisition, long-term maintenance, and generalization of the upkeep skills to a nontraining apartment. General task analyses were recommended for assessment and specific task analyses for training. The impasse correction procedure generally did not produce acquisition. PMID:3710947

40 CFR 92.123 - Test procedure; general requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... designed to determine the brake specific emissions of hydrocarbons (HC, total or non-methane as applicable... of calculating brake specific emissions. (v) The engine may be equipped with a production type...

40 CFR 92.123 - Test procedure; general requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... designed to determine the brake specific emissions of hydrocarbons (HC, total or non-methane as applicable... of calculating brake specific emissions. (v) The engine may be equipped with a production type...

40 CFR 92.123 - Test procedure; general requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... designed to determine the brake specific emissions of hydrocarbons (HC, total or non-methane as applicable... of calculating brake specific emissions. (v) The engine may be equipped with a production type...

40 CFR 92.123 - Test procedure; general requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... designed to determine the brake specific emissions of hydrocarbons (HC, total or non-methane as applicable... of calculating brake specific emissions. (v) The engine may be equipped with a production type...

State University of New York at Stony Brook Main Library Circulation Department Procedures Manual.

ERIC Educational Resources Information Center

Kendrick, Curtis L., Comp.; Lange, Robert, Comp.

Designed to train student circulation desk workers at the State University of New York at Stony Brook's Main Library, this guide details specific procedures and outlines administrative policies. Topics covered include: (1) what circulation is; (2) what is expected of graduate students; (3) the library's opening and closing procedures; (4) who may…

Disentangling the Effects of Context Change and Context Familiarity on Latent Inhibition with a Conditioned Taste Aversion Procedure

ERIC Educational Resources Information Center

De la Casa, L. G.; Mena, A.; Orgaz, A.; Fernandez, A.

2013-01-01

Contextual specificity of Latent Inhibition (LI) has been demonstrated using an ample range of experimental procedures. Context dependence has not been consistently obtained, however, when LI has been induced using a Conditioned Taste Aversion (CTA) procedure. This paper presents two experiments designed to analyze whether the context plays the…

The design, production and clinical application of 3D patient-specific implants with drilling guides for acetabular surgery.

PubMed

Merema, B J; Kraeima, J; Ten Duis, K; Wendt, K W; Warta, R; Vos, E; Schepers, R H; Witjes, M J H; IJpma, F F A

2017-11-01

An innovative procedure for the development of 3D patient-specific implants with drilling guides for acetabular fracture surgery is presented. By using CT data and 3D surgical planning software, a virtual model of the fractured pelvis was created. During this process the fracture was virtually reduced. Based on the reduced fracture model, patient-specific titanium plates including polyamide drilling guides were designed, 3D printed and milled for intra-operative use. One of the advantages of this procedure is that the personalised plates could be tailored to both the shape of the pelvis and the type of fracture. The optimal screw directions and sizes were predetermined in the 3D model. The virtual plan was translated towards the surgical procedure by using the surgical guides and patient-specific osteosynthesis. Besides the description of the newly developed multi-disciplinary workflow, a clinical case example is presented to demonstrate that this technique is feasible and promising for the operative treatment of complex acetabular fractures. Copyright © 2017 Elsevier Ltd. All rights reserved.

Design certification tests: High Pressure Oxygen Filter (HPOF) program. Summary report

NASA Technical Reports Server (NTRS)

Smith, I. D.

1976-01-01

Design and acceptance certification test procedures and results are presented for a high pressure oxygen filter developed to protect the sealing surfaces in emergency oxygen systems. Equipment specifications are included.

49 CFR 178.70 - Approval of UN pressure receptacles.

Code of Federal Regulations, 2010 CFR

2010-10-01

... facility as specified in § 178.69. (7) Design specifications and manufacturing drawings, showing components... compliance with the applicable pressure receptacle design standard. (8) Manufacturing procedures and any applicable standards that describe in detail the manufacturing processes and control. (9) Design type...

Establishing a design procedure for buried steel-reinforced high-density polyethylene pipes : a field study, [technical summary].

DOT National Transportation Integrated Search

2015-11-01

Several national standards and specification have been developed for design, installation, : and materials for precast concrete pipe, corrugated metal pipe, and HDPE pipes. However, : no national accepted installation standard or design method is ava...

40 CFR Figure E-1 to Subpart E of... - Designation Testing Checklist

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Field Sampling Procedure (§ 53.30, .31, .34) Design Specification Tests Filter (L-6) Range of... Testing Physical (Design) and Performance Characteristics of Reference Methods and Class I and Class II... Process or of Documented Evidence: Performance, Design or Application Spec. Corresponding to Sections of...

40 CFR Figure E-1 to Subpart E of... - Designation Testing Checklist

Code of Federal Regulations, 2012 CFR

2012-07-01

...) Field Sampling Procedure (§ 53.30, .31, .34) Design Specification Tests Filter (L-6) Range of... Testing Physical (Design) and Performance Characteristics of Reference Methods and Class I and Class II... Process or of Documented Evidence: Performance, Design or Application Spec. Corresponding to Sections of...

40 CFR Figure E-1 to Subpart E of... - Designation Testing Checklist

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Field Sampling Procedure (§ 53.30, .31, .34) Design Specification Tests Filter ( L-6) Range of... Testing Physical (Design) and Performance Characteristics of Reference Methods and Class I and Class II... Process or of Documented Evidence: Performance, Design or Application Spec. Corresponding to Sections of...

A scalable architecture for incremental specification and maintenance of procedural and declarative clinical decision-support knowledge.

PubMed

Hatsek, Avner; Shahar, Yuval; Taieb-Maimon, Meirav; Shalom, Erez; Klimov, Denis; Lunenfeld, Eitan

2010-01-01

Clinical guidelines have been shown to improve the quality of medical care and to reduce its costs. However, most guidelines exist in a free-text representation and, without automation, are not sufficiently accessible to clinicians at the point of care. A prerequisite for automated guideline application is a machine-comprehensible representation of the guidelines. In this study, we designed and implemented a scalable architecture to support medical experts and knowledge engineers in specifying and maintaining the procedural and declarative aspects of clinical guideline knowledge, resulting in a machine comprehensible representation. The new framework significantly extends our previous work on the Digital electronic Guidelines Library (DeGeL) The current study designed and implemented a graphical framework for specification of declarative and procedural clinical knowledge, Gesher. We performed three different experiments to evaluate the functionality and usability of the major aspects of the new framework: Specification of procedural clinical knowledge, specification of declarative clinical knowledge, and exploration of a given clinical guideline. The subjects included clinicians and knowledge engineers (overall, 27 participants). The evaluations indicated high levels of completeness and correctness of the guideline specification process by both the clinicians and the knowledge engineers, although the best results, in the case of declarative-knowledge specification, were achieved by teams including a clinician and a knowledge engineer. The usability scores were high as well, although the clinicians' assessment was significantly lower than the assessment of the knowledge engineers.

Rationale for windshield glass system specification requirements for shuttle orbiter

NASA Technical Reports Server (NTRS)

Hayashida, K.; King, G. L.; Tesinsiky, J.; Wittenburg, D. R.

1972-01-01

A preliminary procurement specification for the space shuttle orbiter windshield pane, and some of the design considerations and rationale leading to its development are presented. The windshield designer is given the necessary methods and procedures for assuring glass pane structural integrity by proof test. These methods and procedures are fully developed for annealed and thermally tempered aluminosilicate, borosilicate, and soda lime glass and for annealed fused silica. Application of the method to chemically tempered glass is considered. Other considerations are vision requirements, protection against bird impact, hail, frost, rain, and meteoroids. The functional requirements of the windshield system during landing, ferrying, boost, space flight, and entry are included.

Field guide for collecting samples for analysis of volatile organic compounds in stream water for the National Water-Quality Assessment Program

USGS Publications Warehouse

Shelton, Larry R.

1997-01-01

For many years, stream samples for analysis of volatile organic compounds have been collected without specific guidelines or a sampler designed to avoid analyte loss. In 1996, the U.S. Geological Survey's National Water-Quality Assessment Program began aggressively monitoring urban stream-water for volatile organic compounds. To assure representative samples and consistency in collection procedures, a specific sampler was designed to collect samples for analysis of volatile organic compounds in stream water. This sampler, and the collection procedures, were tested in the laboratory and in the field for compound loss, contamination, sample reproducibility, and functional capabilities. This report describes that sampler and its use, and outlines field procedures specifically designed to provide contaminant-free, reproducible volatile organic compound data from stream-water samples. These guidelines and the equipment described represent a significant change in U.S. Geological Survey instructions for collecting and processing stream-water samples for analysis of volatile organic compounds. They are intended to produce data that are both defensible and interpretable, particularly for concentrations below the microgram-per-liter level. The guidelines also contain detailed recommendations for quality-control samples.

Implementation of new OGFC specification.

DOT National Transportation Integrated Search

2006-05-01

The objective of this research is to monitor and document the construction and performance of OGFC on actual field projects. Subsequently, Louisianas OGFC specifications and mix design procedures will be modified as necessary based on the monitori...

17 CFR Appendix A to Part 38 - Guidance on Compliance With Designation Criteria

Code of Federal Regulations, 2011 CFR

2011-04-01

...-matching algorithm and order entry procedures. An application involving a trade-matching algorithm that is... algorithm. (b) A designated contract market's specifications on initial and periodic objective testing and...

17 CFR Appendix A to Part 38 - Guidance on Compliance With Designation Criteria

Code of Federal Regulations, 2012 CFR

2012-04-01

...-matching algorithm and order entry procedures. An application involving a trade-matching algorithm that is... algorithm. (b) A designated contract market's specifications on initial and periodic objective testing and...

Preliminary vibration, acoustic, and shock design and test criteria for components on the SRB, ET, and SSME

NASA Technical Reports Server (NTRS)

1976-01-01

Specifications for vibration, acoustic and shock design for components and subassemblies on the External Tank (ET), Solid Rocket Booster (SRB), and Space Shuttle Main Engine (SSME). Included are vibration, acoustic, shock, transportation, handling, and acceptance test requirements and procedures. The space shuttle ET, SRB, and SSME have been divided into zones and subzones. Zones are designated primarily to assist in determining the applicable specifications. A subzone (General Specification) is available for use when the location of the component is known but component design and weight are not well defined. When the location, weight, and mounting configuration of the component are known, specifications for appropriate subzone weight ranges are available. Criteria for some specific components are also presented.

AgRISTARS: Foreign Commodity production forecasting. Project procedures designation and description document, volume 1

NASA Technical Reports Server (NTRS)

Waggoner, J. T.; Phinney, D. E. (Principal Investigator)

1981-01-01

The crop estimation analysis procedures documentation of the AgRISTARS - Foreign Commodity Production Forecasting Project (FCPF) is presented. Specifically it includes the technical/management documentation of the remote sensing data analysis procedures prepared in accordance with the guidelines provided in the FCPF communication/documentation standards manual. Standard documentation sets are given arranged by procedural type and level then by crop types or other technically differentiating categories.

UDOT calibration of AASHTO's new prestress loss design equations.

DOT National Transportation Integrated Search

2009-07-01

In the next edition of the AASHTO LRFD Bridge Design Specifications the procedure to calculate prestress losses will change dramatically. The new equations are empirically based on high performance concrete from four states (Nebraska, New Hampshire, ...

UDOT's calibration of AASHTO's new prestress loss design equations.

DOT National Transportation Integrated Search

2009-07-01

In the next edition of the AASHTO LRFD Bridge Design Specifications the procedure to calculate prestress losses will change dramatically. The new equations are empirically based on high performance concrete from four states (Nebraska, New Hampshire, ...

Balancing Flexible Constraints and Measurement Precision in Computerized Adaptive Testing

ERIC Educational Resources Information Center

Moyer, Eric L.; Galindo, Jennifer L.; Dodd, Barbara G.

2012-01-01

Managing test specifications--both multiple nonstatistical constraints and flexibly defined constraints--has become an important part of designing item selection procedures for computerized adaptive tests (CATs) in achievement testing. This study compared the effectiveness of three procedures: constrained CAT, flexible modified constrained CAT,…

A solar energy estimation procedure using remote sensing techniques. [watershed hydrologic models

NASA Technical Reports Server (NTRS)

Khorram, S.

1977-01-01

The objective of this investigation is to design a remote sensing-aided procedure for daily location-specific estimation of solar radiation components over the watershed(s) of interest. This technique has been tested on the Spanish Creek Watershed, Northern California, with successful results.

Procedures for Establishing a Contingency Managed Classroom.

ERIC Educational Resources Information Center

Westinghouse Learning Corp., Albuquerque, NM. Behavior Systems Div.

This manual for classroom teachers is designed to teach the application of contingency contracting procedures in the typical instructional setting. A "contingency contract" is an agreement between teacher and student whereby the student, upon demonstration of specific task achievement, receives a reward: permission to participate in a "reinforcing…

Advanced Lockouts: Reengineering Safety Programs for Efficiency.

PubMed

Michalscheck, Jimi

2015-08-01

Remember one golden rule when engineering out lockout/tagout: No additional risk can be introduced to the employees by using alternative procedures. If you can design alternative procedures and an overall alternative program to ensure equivalent protection for specific tasks...the sky is the limit to enhancing productivity.

Instructional Aides: Employment, Payroll Procedures, Supervision, Performance Appraisal, Legal Aspects.

ERIC Educational Resources Information Center

Nielsen, Earl T.

Designed to assist school administrators in their efforts to secure, train, and retain the most qualified instructional aides available, the monograph discusses procedures for employment, payroll processing, aide supervision, performance appraisal, and legal aspects involved in the hiring of instructional aides. Specific topics include…

Engineering Bacteria to Search for Specific Concentrations of Molecules by a Systematic Synthetic Biology Design Method

PubMed Central

Chen, Bor-Sen

2016-01-01

Bacteria navigate environments full of various chemicals to seek favorable places for survival by controlling the flagella’s rotation using a complicated signal transduction pathway. By influencing the pathway, bacteria can be engineered to search for specific molecules, which has great potential for application to biomedicine and bioremediation. In this study, genetic circuits were constructed to make bacteria search for a specific molecule at particular concentrations in their environment through a synthetic biology method. In addition, by replacing the “brake component” in the synthetic circuit with some specific sensitivities, the bacteria can be engineered to locate areas containing specific concentrations of the molecule. Measured by the swarm assay qualitatively and microfluidic techniques quantitatively, the characteristics of each “brake component” were identified and represented by a mathematical model. Furthermore, we established another mathematical model to anticipate the characteristics of the “brake component”. Based on this model, an abundant component library can be established to provide adequate component selection for different searching conditions without identifying all components individually. Finally, a systematic design procedure was proposed. Following this systematic procedure, one can design a genetic circuit for bacteria to rapidly search for and locate different concentrations of particular molecules by selecting the most adequate “brake component” in the library. Moreover, following simple procedures, one can also establish an exclusive component library suitable for other cultivated environments, promoter systems, or bacterial strains. PMID:27096615

A decision support system-based procedure for evaluation and monitoring of protected areas sustainability for the Mediterranean region

NASA Astrophysics Data System (ADS)

Pediaditi, K.; Buono, F.; Pompigna, F.; Bogliotti, C.; Nurlu, E.; Ladisa, G.; Petropoulos, G. P.

2011-10-01

Despite common acknowledgement of the value of protected areas as instruments in ensuring sustainability, and their promotion for the achievement of policies on halting the loss of biodiversity, there is no common approach today for monitoring and evaluating them. This paper presents a novel integrated nature conservation management procedure developed to monitor and evaluate the sustainability of Mediterranean protected areas. This procedure was successfully implemented and formally evaluated by protected area managers in six Mediterranean countries, results of which are presented here together with an overview of the web-based Decision Support System (DSS) developed to facilitate its wide adoption. The DSS and procedure has been designed and evaluated by managers as a useful tool, which facilitates and provides needed procedural guidance for protected area monitoring whilst minimizing input requirements to do so. The procedure and DSS were developed following a review of existing protected area assessment tools and a detailed primary investigation of the needs and capacity of its intended users. Essentially, the procedure and DSS guides provide the facilities for protected area managers, in following a participatory approach to develop a context-specific sustainability monitoring strategy, for their protected area. Consequently, the procedure is, by design, participatory, context specific, holistic and relevant to protected area management and institutional procedures. The procedure was piloted and formally evaluated in Greece, Italy, Turkey, Egypt, Malta and Cyprus. Feedback collected from the pilot evaluations is also summarised herein.

Land Application of Wastes: An Educational Program. Design Procedures for Land Application of Wastes - Module 6, Objectives, Script and Figures.

ERIC Educational Resources Information Center

Clarkson, W. W.; And Others

The purpose of this module is to develop a general procedure to decide the feasibility of land application as a waste management alternative, given a specific problem situation. This information provides a framework within which to apply the information presented in all other modules in the program. An outline of the general procedure followed in…

Shear capacity of in service prestressed concrete bridge girders.

DOT National Transportation Integrated Search

2010-05-17

The design of prestressed concrete bridge girders has changed significantly over the past several : decades. Specifically, the design procedure to calculate the shear capacity of bridge girders that : was used forty years ago is very different than t...

Step by Step: Biology Undergraduates' Problem-Solving Procedures during Multiple-Choice Assessment.

PubMed

Prevost, Luanna B; Lemons, Paula P

2016-01-01

This study uses the theoretical framework of domain-specific problem solving to explore the procedures students use to solve multiple-choice problems about biology concepts. We designed several multiple-choice problems and administered them on four exams. We trained students to produce written descriptions of how they solved the problem, and this allowed us to systematically investigate their problem-solving procedures. We identified a range of procedures and organized them as domain general, domain specific, or hybrid. We also identified domain-general and domain-specific errors made by students during problem solving. We found that students use domain-general and hybrid procedures more frequently when solving lower-order problems than higher-order problems, while they use domain-specific procedures more frequently when solving higher-order problems. Additionally, the more domain-specific procedures students used, the higher the likelihood that they would answer the problem correctly, up to five procedures. However, if students used just one domain-general procedure, they were as likely to answer the problem correctly as if they had used two to five domain-general procedures. Our findings provide a categorization scheme and framework for additional research on biology problem solving and suggest several important implications for researchers and instructors. © 2016 L. B. Prevost and P. P. Lemons. CBE—Life Sciences Education © 2016 The American Society for Cell Biology. This article is distributed by The American Society for Cell Biology under license from the author(s). It is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

10 CFR 435.302 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., or both, or a domestic hot water system, and (2) For which a building design is created after the effective date of this rule. (f) Building design means the development of plans and specifications for human... computerized calculation procedure that is used to establish an energy consumption goal for the design of...

A new design approach to innovative spectrometers. Case study: TROPOLITE

NASA Astrophysics Data System (ADS)

Volatier, Jean-Baptiste; Baümer, Stefan; Kruizinga, Bob; Vink, Rob

2014-05-01

Designing a novel optical system is a nested iterative process. The optimization loop, from a starting point to final system is already mostly automated. However this loop is part of a wider loop which is not. This wider loop starts with an optical specification and ends with a manufacturability assessment. When designing a new spectrometer with emphasis on weight and cost, numerous iterations between the optical- and mechanical designer are inevitable. The optical designer must then be able to reliably produce optical designs based on new input gained from multidisciplinary studies. This paper presents a procedure that can automatically generate new starting points based on any kind of input or new constraint that might arise. These starting points can then be handed over to a generic optimization routine to make the design tasks extremely efficient. The optical designer job is then not to design optical systems, but to meta-design a procedure that produces optical systems paving the way for system level optimization. We present here this procedure and its application to the design of TROPOLITE a lightweight push broom imaging spectrometer.

Comparative Robustness of Recent Methods for Analyzing Multivariate Repeated Measures Designs

ERIC Educational Resources Information Center

Seco, Guillermo Vallejo; Gras, Jaime Arnau; Garcia, Manuel Ato

2007-01-01

This study evaluated the robustness of two recent methods for analyzing multivariate repeated measures when the assumptions of covariance homogeneity and multivariate normality are violated. Specifically, the authors' work compares the performance of the modified Brown-Forsythe (MBF) procedure and the mixed-model procedure adjusted by the…

40 CFR 62.15120 - What information must I include in the plant-specific operating manual?

Code of Federal Regulations, 2013 CFR

2013-07-01

... startup, shutdown, and malfunction of the municipal waste combustion unit. (e) Procedures for maintaining... DESIGNATED FACILITIES AND POLLUTANTS Federal Plan Requirements for Small Municipal Waste Combustion Units... the basic combustion principles that apply to municipal waste combustion units. (c) Procedures for...

Fracture control procedures for aircraft structural integrity

NASA Technical Reports Server (NTRS)

Wood, H. A.

1972-01-01

The application of applied fracture mechanics in the design, analysis, and qualification of aircraft structural systems are reviewed. Recent service experiences are cited. Current trends in high-strength materials application are reviewed with particular emphasis on the manner in which fracture toughness and structural efficiency may affect the material selection process. General fracture control procedures are reviewed in depth with specific reference to the impact of inspectability, structural arrangement, and material on proposed analysis requirements for safe crack growth. The relative impact on allowable design stress is indicated by example. Design criteria, material, and analysis requirements for implementation of fracture control procedures are reviewed together with limitations in current available data techniques. A summary of items which require further study and attention is presented.

Surgeon specialization and operative mortality in United States: retrospective analysis

PubMed Central

Dalton, Maurice; Cutler, David M; Birkmeyer, John D; Chandra, Amitabh

2016-01-01

Objective To measure the association between a surgeon’s degree of specialization in a specific procedure and patient mortality. Design Retrospective analysis of Medicare data. Setting US patients aged 66 or older enrolled in traditional fee for service Medicare. Participants 25 152 US surgeons who performed one of eight procedures (carotid endarterectomy, coronary artery bypass grafting, valve replacement, abdominal aortic aneurysm repair, lung resection, cystectomy, pancreatic resection, or esophagectomy) on 695 987 patients in 2008-13. Main outcome measure Relative risk reduction in risk adjusted and volume adjusted 30 day operative mortality between surgeons in the bottom quarter and top quarter of surgeon specialization (defined as the number of times the surgeon performed the specific procedure divided by his/her total operative volume across all procedures). Results For all four cardiovascular procedures and two out of four cancer resections, a surgeon’s degree of specialization was a significant predictor of operative mortality independent of the number of times he or she performed that procedure: carotid endarterectomy (relative risk reduction between bottom and top quarter of surgeons 28%, 95% confidence interval 0% to 48%); coronary artery bypass grafting (15%, 4% to 25%); valve replacement (46%, 37% to 53%); abdominal aortic aneurysm repair (42%, 29% to 53%); lung resection (28%, 5% to 46%); and cystectomy (41%, 8% to 63%). In five procedures (carotid endarterectomy, valve replacement, lung resection, cystectomy, and esophagectomy), the relative risk reduction from surgeon specialization was greater than that from surgeon volume for that specific procedure. Furthermore, surgeon specialization accounted for 9% (coronary artery bypass grafting) to 100% (cystectomy) of the relative risk reduction otherwise attributable to volume in that specific procedure. Conclusion For several common procedures, surgeon specialization was an important predictor of operative mortality independent of volume in that specific procedure. When selecting a surgeon, patients, referring physicians, and administrators assigning operative workload may want to consider a surgeon’s procedure specific volume as well as the degree to which a surgeon specializes in that procedure. PMID:27444190

An RC active filter design handbook

NASA Technical Reports Server (NTRS)

Deboo, G. J.

1977-01-01

The design of filters is described. Emphasis is placed on simplified procedures that can be used by the reader who has minimum knowledge about circuit design and little acquaintance with filter theory. The handbook has three main parts. The first part is a review of some information that is essential for work with filters. The second part includes design information for specific types of filter circuitry and describes simple procedures for obtaining the component values for a filter that will have a desired set of characteristics. Pertinent information relating to actual performance is given. The third part (appendix) is a review of certain topics in filter theory and is intended to provide some basic understanding of how filters are designed.

Optimum Design of High-Speed Prop-Rotors

NASA Technical Reports Server (NTRS)

Chattopadhyay, Aditi; McCarthy, Thomas Robert

1993-01-01

An integrated multidisciplinary optimization procedure is developed for application to rotary wing aircraft design. The necessary disciplines such as dynamics, aerodynamics, aeroelasticity, and structures are coupled within a closed-loop optimization process. The procedure developed is applied to address two different problems. The first problem considers the optimization of a helicopter rotor blade and the second problem addresses the optimum design of a high-speed tilting proprotor. In the helicopter blade problem, the objective is to reduce the critical vibratory shear forces and moments at the blade root, without degrading rotor aerodynamic performance and aeroelastic stability. In the case of the high-speed proprotor, the goal is to maximize the propulsive efficiency in high-speed cruise without deteriorating the aeroelastic stability in cruise and the aerodynamic performance in hover. The problems studied involve multiple design objectives; therefore, the optimization problems are formulated using multiobjective design procedures. A comprehensive helicopter analysis code is used for the rotary wing aerodynamic, dynamic and aeroelastic stability analyses and an algorithm developed specifically for these purposes is used for the structural analysis. A nonlinear programming technique coupled with an approximate analysis procedure is used to perform the optimization. The optimum blade designs obtained in each case are compared to corresponding reference designs.

49 CFR 179.3 - Procedure for securing approval.

Code of Federal Regulations, 2012 CFR

2012-10-01

... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS... Safety, AAR, for consideration by its Tank Car Committee and other appropriate committees. Approval or... designs, materials and construction, conversion or alteration of tank car tanks under these specifications...

49 CFR 179.3 - Procedure for securing approval.

Code of Federal Regulations, 2014 CFR

2014-10-01

... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS... Safety, AAR, for consideration by its Tank Car Committee and other appropriate committees. Approval or... designs, materials and construction, conversion or alteration of tank car tanks under these specifications...

49 CFR 179.3 - Procedure for securing approval.

Code of Federal Regulations, 2011 CFR

2011-10-01

... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS... Safety, AAR, for consideration by its Tank Car Committee and other appropriate committees. Approval or... designs, materials and construction, conversion or alteration of tank car tanks under these specifications...

49 CFR 179.3 - Procedure for securing approval.

Code of Federal Regulations, 2013 CFR

2013-10-01

... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS... Safety, AAR, for consideration by its Tank Car Committee and other appropriate committees. Approval or... designs, materials and construction, conversion or alteration of tank car tanks under these specifications...

46 CFR 162.050-1 - Scope.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Pollution Prevention Equipment § 162.050-1 Scope. (a) This subpart contains... specifications for this equipment; (3) Tests required for approval; (4) Procedures for obtaining designation as a...

Shear capacity of in service pre-stressed concrete bridge girders.

DOT National Transportation Integrated Search

2010-05-17

The design of prestressed concrete bridge girders has changed significantly over the past several decades. Specifically, the design procedure to calculate the shear capacity of bridge girders that was used forty years ago is very different than those...

IMCS reflight certification requirements and design specifications

NASA Technical Reports Server (NTRS)

1984-01-01

The requirements for reflight certification are established. Software requirements encompass the software programs that are resident in the PCC, DEP, PDSS, EC, or any related GSE. A design approach for the reflight software packages is recommended. These designs will be of sufficient detail to permit the implementation of reflight software. The PDSS/IMC Reflight Certification system provides the tools and mechanisms for the user to perform the reflight certification test procedures, test data capture, test data display, and test data analysis. The system as defined will be structured to permit maximum automation of reflight certification procedures and test data analysis.

Technical specification for vacuum systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khaw, J.

The vacuum systems at the Stanford Linear Accelerator Center (SLAC) are primarily of all-metal construction and operate at pressures from 10/sup -5/ to 10/sup -11/ Torr. The primary gas loads during operation result from thermal desorption and beam-induced desorption from the vacuum chamber walls. These desorption rates can be extremely high in the case of hydrocarbons and other contaminants. These specifications place a major emphasis on eliminating contamination sources. The specifications and procedures have been written to insure the cleanliness and vacuum integrity of all SLAC vacuum systems, and to assist personnel involved with SLAC vacuum systems in choosing andmore » designing components that are compatible with existing systems and meet the quality and reliability of SLAC vacuum standards. The specification includes requirements on design, procurement, fabrication, chemical cleaning, clean room practices, welding and brazing, helium leak testing, residual gas analyzer testing, bakeout, venting, and pumpdown. Also appended are specifications regarding acceptable vendors, isopropyl alcohol, bakeable valve cleaning procedure, mechanical engineering safety inspection, notes on synchrotron radiation, and specifications of numerous individual components. (LEW)« less

Interdisciplinary Development of an Improved Emergency Department Procedural Work Surface Through Iterative Design and Use Testing in Simulated and Clinical Environments.

PubMed

Zhang, Xiao C; Bermudez, Ana M; Reddy, Pranav M; Sarpatwari, Ravi R; Chheng, Darin B; Mezoian, Taylor J; Schwartz, Victoria R; Simmons, Quinneil J; Jay, Gregory D; Kobayashi, Leo

2017-03-01

A stable and readily accessible work surface for bedside medical procedures represents a valuable tool for acute care providers. In emergency department (ED) settings, the design and implementation of traditional Mayo stands and related surface devices often limit their availability, portability, and usability, which can lead to suboptimal clinical practice conditions that may affect the safe and effective performance of medical procedures and delivery of patient care. We designed and built a novel, open-source, portable, bedside procedural surface through an iterative development process with use testing in simulated and live clinical environments. The procedural surface development project was conducted between October 2014 and June 2016 at an academic referral hospital and its affiliated simulation facility. An interdisciplinary team of emergency physicians, mechanical engineers, medical students, and design students sought to construct a prototype bedside procedural surface out of off-the-shelf hardware during a collaborative university course on health care design. After determination of end-user needs and core design requirements, multiple prototypes were fabricated and iteratively modified, with early variants featuring undermattress stabilizing supports or ratcheting clamp mechanisms. Versions 1 through 4 underwent 2 hands-on usability-testing simulation sessions; version 5 was presented at a design critique held jointly by a panel of clinical and industrial design faculty for expert feedback. Responding to select feedback elements over several surface versions, investigators arrived at a near-final prototype design for fabrication and use testing in a live clinical setting. This experimental procedural surface (version 8) was constructed and then deployed for controlled usability testing against the standard Mayo stands in use at the study site ED. Clinical providers working in the ED who opted to participate in the study were provided with the prototype surface and just-in-time training on its use when performing bedside procedures. Subjects completed the validated 10-point System Usability Scale postshift for the surface that they had used. The study protocol was approved by the institutional review board. Multiple prototypes and recursive design revisions resulted in a fully functional, portable, and durable bedside procedural surface that featured a stainless steel tray and intuitive hook-and-lock mechanisms for attachment to ED stretcher bed rails. Forty-two control and 40 experimental group subjects participated and completed questionnaires. The median System Usability Scale score (out of 100; higher scores associated with better usability) was 72.5 (interquartile range [IQR] 51.3 to 86.3) for the Mayo stand; the experimental surface was scored at 93.8 (IQR 84.4 to 97.5 for a difference in medians of 17.5 (95% confidence interval 10 to 27.5). Subjects reported several usability challenges with the Mayo stand; the experimental surface was reviewed as easy to use, simple, and functional. In accordance with experimental live environment deployment, questionnaire responses, and end-user suggestions, the project team finalized the design specification for the experimental procedural surface for open dissemination. An iterative, interdisciplinary approach was used to generate, evaluate, revise, and finalize the design specification for a new procedural surface that met all core end-user requirements. The final surface design was evaluated favorably on a validated usability tool against Mayo stands when use tested in simulated and live clinical settings. Copyright © 2016 American College of Emergency Physicians. Published by Elsevier Inc. All rights reserved.

Performance and capacity assessment of reinforced concrete bridge piers considering the current load and resistance factor design provisions and plastic hinge length in Kansas.

DOT National Transportation Integrated Search

2014-05-01

Kansas Department of Transportation (KDOT) has implemented the new AASHTO-LRFD provisions in the state specific : LRFD design procedure (KDOT LRFD). Most of the existing bridges constructed before the new provisions, have been designed : based on the...

Into the Curriculum.

ERIC Educational Resources Information Center

School Library Media Activities Monthly, 1996

1996-01-01

Provides five fully developed library media activities designed for use with specific curriculum units in art, health and nutrition, mathematics, science, and social studies. Library media skills, objectives, grade levels, instructional roles, procedures, evaluation, and follow-up are described for each activity. Specific topics include aardvarks,…

Erosion protection for soil slopes along Virginia's highways.

DOT National Transportation Integrated Search

2000-01-01

A survey of the state of practice for designing slope erosion control measures within VDOT's nine districts has been conducted. On the basis of the survey, it is clear that there are no specific design procedures currently in use within VDOT for deal...

19 CFR 115.26 - Eligibility.

Code of Federal Regulations, 2012 CFR

2012-04-01

... CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.26 Eligibility. Any manufacturer of containers to be manufactured in a type series from standard design and specifications so that each container has identical...

19 CFR 115.26 - Eligibility.

Code of Federal Regulations, 2010 CFR

2010-04-01

... CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.26 Eligibility. Any manufacturer of containers to be manufactured in a type series from standard design and specifications so that each container has identical...

19 CFR 115.26 - Eligibility.

Code of Federal Regulations, 2011 CFR

2011-04-01

... CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.26 Eligibility. Any manufacturer of containers to be manufactured in a type series from standard design and specifications so that each container has identical...

19 CFR 115.26 - Eligibility.

Code of Federal Regulations, 2014 CFR

2014-04-01

... CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.26 Eligibility. Any manufacturer of containers to be manufactured in a type series from standard design and specifications so that each container has identical...

19 CFR 115.26 - Eligibility.

Code of Federal Regulations, 2013 CFR

2013-04-01

... CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.26 Eligibility. Any manufacturer of containers to be manufactured in a type series from standard design and specifications so that each container has identical...

Surrogate decision making: do we have to trade off accuracy and procedural satisfaction?

PubMed

Frey, Renato; Hertwig, Ralph; Herzog, Stefan M

2014-02-01

Making surrogate decisions on behalf of incapacitated patients can raise difficult questions for relatives, physicians, and society. Previous research has focused on the accuracy of surrogate decisions (i.e., the proportion of correctly inferred preferences). Less attention has been paid to the procedural satisfaction that patients' surrogates and patients attribute to specific approaches to making surrogate decisions. The objective was to investigate hypothetical patients' and surrogates' procedural satisfaction with specific approaches to making surrogate decisions and whether implementing these preferences would lead to tradeoffs between procedural satisfaction and accuracy. Study 1 investigated procedural satisfaction by assigning participants (618 in a mixed-age but relatively young online sample and 50 in an older offline sample) to the roles of hypothetical surrogates or patients. Study 2 (involving 64 real multigenerational families with a total of 253 participants) investigated accuracy using 24 medical scenarios. Hypothetical patients and surrogates had closely aligned preferences: Procedural satisfaction was highest with a patient-designated surrogate, followed by shared surrogate decision-making approaches and legally assigned surrogates. These approaches did not differ substantially in accuracy. Limitations are that participants' preferences regarding existing and novel approaches to making surrogate decisions can only be elicited under hypothetical conditions. Next to decision making by patient-designated surrogates, shared surrogate decision making is the preferred approach among patients and surrogates alike. This approach appears to impose no tradeoff between procedural satisfaction and accuracy. Therefore, shared decision making should be further studied in representative samples of the general population, and if people's preferences prove to be robust, they deserve to be weighted more strongly in legal frameworks in addition to patient-designated surrogates.

NGA-West 2 GMPE average site coefficients for use in earthquake-resistant design

USGS Publications Warehouse

Borcherdt, Roger D.

2015-01-01

Site coefficients corresponding to those in tables 11.4–1 and 11.4–2 of Minimum Design Loads for Buildings and Other Structures published by the American Society of Civil Engineers (Standard ASCE/SEI 7-10) are derived from four of the Next Generation Attenuation West2 (NGA-W2) Ground-Motion Prediction Equations (GMPEs). The resulting coefficients are compared with those derived by other researchers and those derived from the NGA-West1 database. The derivation of the NGA-W2 average site coefficients provides a simple procedure to update site coefficients with each update in the Maximum Considered Earthquake Response MCER maps. The simple procedure yields average site coefficients consistent with those derived for site-specific design purposes. The NGA-W2 GMPEs provide simple scale factors to reduce conservatism in current simplified design procedures.

DESIGN CRITERIA FOR HIGH TEMPERATURE LATTICE TEST REACTOR PROJECT CAH-100

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ballard, D.L.; Brown, W.W.; Harrison, C.W.

Design and construction specifications to be followed in the development of the reactor, its associated systems and experimental facilities, and the housing and required services for the facility are presented. The testing procedures to be used are outlined. (D.C.W.)

Modified Standard Penetration Test–based Drilled Shaft Design Method for Weak Rocks (Phase 2 Study)

DOT National Transportation Integrated Search

2017-12-15

In this project, Illinois-specific design procedures were developed for drilled shafts founded in weak shale or rock. In particular, a modified standard penetration test was developed and verified to characterize the in situ condition of weak shales ...

Image-Based Patient-Specific Ventricle Models with Fluid-Structure Interaction for Cardiac Function Assessment and Surgical Design Optimization

PubMed Central

Tang, Dalin; Yang, Chun; Geva, Tal; del Nido, Pedro J.

2010-01-01

Recent advances in medical imaging technology and computational modeling techniques are making it possible that patient-specific computational ventricle models be constructed and used to test surgical hypotheses and replace empirical and often risky clinical experimentation to examine the efficiency and suitability of various reconstructive procedures in diseased hearts. In this paper, we provide a brief review on recent development in ventricle modeling and its potential application in surgical planning and management of tetralogy of Fallot (ToF) patients. Aspects of data acquisition, model selection and construction, tissue material properties, ventricle layer structure and tissue fiber orientations, pressure condition, model validation and virtual surgery procedures (changing patient-specific ventricle data and perform computer simulation) were reviewed. Results from a case study using patient-specific cardiac magnetic resonance (CMR) imaging and right/left ventricle and patch (RV/LV/Patch) combination model with fluid-structure interactions (FSI) were reported. The models were used to evaluate and optimize human pulmonary valve replacement/insertion (PVR) surgical procedure and patch design and test a surgical hypothesis that PVR with small patch and aggressive scar tissue trimming in PVR surgery may lead to improved recovery of RV function and reduced stress/strain conditions in the patch area. PMID:21344066

Redesigning the specificity of protein-DNA interactions with Rosetta.

PubMed

Thyme, Summer; Baker, David

2014-01-01

Building protein tools that can selectively bind or cleave specific DNA sequences requires efficient technologies for modifying protein-DNA interactions. Computational design is one method for accomplishing this goal. In this chapter, we present the current state of protein-DNA interface design with the Rosetta macromolecular modeling program. The LAGLIDADG endonuclease family of DNA-cleaving enzymes, under study as potential gene therapy reagents, has been the main testing ground for these in silico protocols. At this time, the computational methods are most useful for designing endonuclease variants that can accommodate small numbers of target site substitutions. Attempts to engineer for more extensive interface changes will likely benefit from an approach that uses the computational design results in conjunction with a high-throughput directed evolution or screening procedure. The family of enzymes presents an engineering challenge because their interfaces are highly integrated and there is significant coordination between the binding and catalysis events. Future developments in the computational algorithms depend on experimental feedback to improve understanding and modeling of these complex enzymatic features. This chapter presents both the basic method of design that has been successfully used to modulate specificity and more advanced procedures that incorporate DNA flexibility and other properties that are likely necessary for reliable modeling of more extensive target site changes.

Virtual surgical planning, flow simulation, and 3-dimensional electrospinning of patient-specific grafts to optimize Fontan hemodynamics.

PubMed

Siallagan, Dominik; Loke, Yue-Hin; Olivieri, Laura; Opfermann, Justin; Ong, Chin Siang; de Zélicourt, Diane; Petrou, Anastasios; Daners, Marianne Schmid; Kurtcuoglu, Vartan; Meboldt, Mirko; Nelson, Kevin; Vricella, Luca; Johnson, Jed; Hibino, Narutoshi; Krieger, Axel

2018-04-01

Despite advances in the Fontan procedure, there is an unmet clinical need for patient-specific graft designs that are optimized for variations in patient anatomy. The objective of this study is to design and produce patient-specific Fontan geometries, with the goal of improving hepatic flow distribution (HFD) and reducing power loss (P loss ), and manufacturing these designs by electrospinning. Cardiac magnetic resonance imaging data from patients who previously underwent a Fontan procedure (n = 2) was used to create 3-dimensional models of their native Fontan geometry using standard image segmentation and geometry reconstruction software. For each patient, alternative designs were explored in silico, including tube-shaped and bifurcated conduits, and their performance in terms of P loss and HFD probed by computational fluid dynamic (CFD) simulations. The best-performing options were then fabricated using electrospinning. CFD simulations showed that the bifurcated conduit improved HFD between the left and right pulmonary arteries, whereas both types of conduits reduced P loss . In vitro testing with a flow-loop chamber supported the CFD results. The proposed designs were then successfully electrospun into tissue-engineered vascular grafts. Our unique virtual cardiac surgery approach has the potential to improve the quality of surgery by manufacturing patient-specific designs before surgery, that are also optimized with balanced HFD and minimal P loss , based on refinement of commercially available options for image segmentation, computer-aided design, and flow simulations. Copyright © 2017 The American Association for Thoracic Surgery. Published by Elsevier Inc. All rights reserved.

36 CFR 907.5 - Specific responsibilities of designated Corporation official.

Code of Federal Regulations, 2010 CFR

2010-07-01

... pertaining to environmental protection and enhancement. (b) Establish and maintain working relationships with... Corporation's implementation of standards, procedures, and working relationships for protection and...

Project visual analysis for the Allegheny National Forest

Treesearch

Gary W. Kell

1979-01-01

The Project Visual Analysis is a landscape assessment procedure involving forest vegetative manipulation. A logical step by step analysis leads the user to a specific set of landscape management guidelines to be used as an aid in designing a project or in evaluating whether the proposed project impacts will meet visual objectives. Key elements within the procedure are...

Step by Step: Biology Undergraduates' Problem-Solving Procedures during Multiple-Choice Assessment

ERIC Educational Resources Information Center

Prevost, Luanna B.; Lemons, Paula P.

2016-01-01

This study uses the theoretical framework of domain-specific problem solving to explore the procedures students use to solve multiple-choice problems about biology concepts. We designed several multiple-choice problems and administered them on four exams. We trained students to produce written descriptions of how they solved the problem, and this…

Design of Energy Storage Reactors for Dc-To-Dc Converters. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Chen, D. Y.

1975-01-01

Two methodical approaches to the design of energy-storage reactors for a group of widely used dc-to-dc converters are presented. One of these approaches is based on a steady-state time-domain analysis of piecewise-linearized circuit models of the converters, while the other approach is based on an analysis of the same circuit models, but from an energy point of view. The design procedure developed from the first approach includes a search through a stored data file of magnetic core characteristics and results in a list of usable reactor designs which meet a particular converter's requirements. Because of the complexity of this procedure, a digital computer usually is used to implement the design algorithm. The second approach, based on a study of the storage and transfer of energy in the magnetic reactors, leads to a straightforward design procedure which can be implemented with hand calculations. An equation to determine the lower-bound volume of workable cores for given converter design specifications is derived. Using this computer lower-bound volume, a comparative evaluation of various converter configurations is presented.

40 CFR 92.113 - Fuel specifications.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) CONTROL OF AIR POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Test Procedures § 92.113 Fuel specifications. (a) Diesel test fuel. (1) The diesel fuels for testing locomotives or locomotive engines designed...) of this section shall be reported in accordance with § 92.133. (b) Natural gas test fuel (compressed...

40 CFR 92.113 - Fuel specifications.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) CONTROL OF AIR POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Test Procedures § 92.113 Fuel specifications. (a) Diesel test fuel. (1) The diesel fuels for testing locomotives or locomotive engines designed... section shall be reported in accordance with § 92.133. (b) Natural gas test fuel (compressed natural gas...

40 CFR 92.113 - Fuel specifications.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) CONTROL OF AIR POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Test Procedures § 92.113 Fuel specifications. (a) Diesel test fuel. (1) The diesel fuels for testing locomotives or locomotive engines designed... section shall be reported in accordance with § 92.133. (b) Natural gas test fuel (compressed natural gas...

40 CFR 92.113 - Fuel specifications.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) CONTROL OF AIR POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Test Procedures § 92.113 Fuel specifications. (a) Diesel test fuel. (1) The diesel fuels for testing locomotives or locomotive engines designed... section shall be reported in accordance with § 92.133. (b) Natural gas test fuel (compressed natural gas...

40 CFR 92.113 - Fuel specifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) CONTROL OF AIR POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Test Procedures § 92.113 Fuel specifications. (a) Diesel test fuel. (1) The diesel fuels for testing locomotives or locomotive engines designed...) of this section shall be reported in accordance with § 92.133. (b) Natural gas test fuel (compressed...

Sustainable Design of EPA's Campus in Research Triangle Park, NC—Environmental Performance Specifications in Construction Contracts—Section 01450 Sequence of Finishes Installation

EPA Pesticide Factsheets

Learn more about the special construction scheduling/sequencing requirements and procedures necessary to assure achievement of designed Indoor Air Quality (IAQ) levels for the completed project required by the EPA IAQ Program.

Investigating Preservice Mathematics Teachers' Manipulative Material Design Processes

ERIC Educational Resources Information Center

Sandir, Hakan

2016-01-01

Students use concrete manipulatives to form an imperative affiliation between conceptual and procedural knowledge (Balka, 1993). Hence, it is necessary to design specific mathematics manipulatives that focus on different mathematical concepts. Preservice teachers need to know how to make and use manipulatives that stimulate students' thinking as…

19 CFR 115.29 - Plan review.

Code of Federal Regulations, 2014 CFR

2014-04-01

... CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.29 Plan review. (a) A manufacturer or owner who wants containers to be approved by design type must submit the plans and specifications for the container to the...

19 CFR 115.29 - Plan review.

Code of Federal Regulations, 2011 CFR

2011-04-01

... CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.29 Plan review. (a) A manufacturer or owner who wants containers to be approved by design type must submit the plans and specifications for the container to the...

19 CFR 115.29 - Plan review.

Code of Federal Regulations, 2010 CFR

2010-04-01

... CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.29 Plan review. (a) A manufacturer or owner who wants containers to be approved by design type must submit the plans and specifications for the container to the...

19 CFR 115.29 - Plan review.

Code of Federal Regulations, 2013 CFR

2013-04-01

... CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.29 Plan review. (a) A manufacturer or owner who wants containers to be approved by design type must submit the plans and specifications for the container to the...

19 CFR 115.29 - Plan review.

Code of Federal Regulations, 2012 CFR

2012-04-01

... CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.29 Plan review. (a) A manufacturer or owner who wants containers to be approved by design type must submit the plans and specifications for the container to the...

Design verification of SIFT

NASA Technical Reports Server (NTRS)

Moser, Louise; Melliar-Smith, Michael; Schwartz, Richard

1987-01-01

A SIFT reliable aircraft control computer system, designed to meet the ultrahigh reliability required for safety critical flight control applications by use of processor replications and voting, was constructed for SRI, and delivered to NASA Langley for evaluation in the AIRLAB. To increase confidence in the reliability projections for SIFT, produced by a Markov reliability model, SRI constructed a formal specification, defining the meaning of reliability in the context of flight control. A further series of specifications defined, in increasing detail, the design of SIFT down to pre- and post-conditions on Pascal code procedures. Mechanically checked mathematical proofs were constructed to demonstrate that the more detailed design specifications for SIFT do indeed imply the formal reliability requirement. An additional specification defined some of the assumptions made about SIFT by the Markov model, and further proofs were constructed to show that these assumptions, as expressed by that specification, did indeed follow from the more detailed design specifications for SIFT. This report provides an outline of the methodology used for this hierarchical specification and proof, and describes the various specifications and proofs performed.

Specification and verification of gate-level VHDL models of synchronous and asynchronous circuits

NASA Technical Reports Server (NTRS)

Russinoff, David M.

1995-01-01

We present a mathematical definition of hardware description language (HDL) that admits a semantics-preserving translation to a subset of VHDL. Our HDL includes the basic VHDL propagation delay mechanisms and gate-level circuit descriptions. We also develop formal procedures for deriving and verifying concise behavioral specifications of combinational and sequential devices. The HDL and the specification procedures have been formally encoded in the computational logic of Boyer and Moore, which provides a LISP implementation as well as a facility for mechanical proof-checking. As an application, we design, specify, and verify a circuit that achieves asynchronous communication by means of the biphase mark protocol.

Comparing Architectural Styles for Service-Oriented Architectures - a REST vs. SOAP Case Study

NASA Astrophysics Data System (ADS)

Becker, Jörg; Matzner, Martin; Müller, Oliver

Two architectural styles are currently heavily discussed regarding the design of service-oriented architectures (SOA). Within this chapter we have compared those two alternative styles - the SOAP-style with procedural designs similar to remote procedure calls and the REST-style with loosely coupled services similar to resources of the World Wide Web. We introduce the case of a business network consisting of manufacturers and service providers of the electronics industry for deriving a set of requirements towards a specific SOA implementation. For each architectural style we present a concrete SOA design and evaluate it against the defined set of requirements.

Electric Utility Rate Design Study: reference manual and procedures for implementing PURPA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

State regulatory commissions will be assisted by using this manual in carrying out their responsibilities under the National Energy Act, specifically under the Public Utilities Regulatory Policies Act (PURPA). The research and materials of the Rate Design Study are basically applicable to Title I of PURPA, and the Manual covers only that part of the Act. The Rate Design Study covers a wide scope of research and professional opinions and are a major reference source for data, information, and divergent views on practically every aspect of electric utility rate design. The introductory part calls attention to particularly important aspects ofmore » responsibilities, authority, and procedures. The second part outlines the specific responsibilities placed by Title I of PURPA on the State commissions. Part 3 discusses some of the procedural and substantive requirements and options of PURPA with particular emphasis on their relation to the Rate Design Study, State law, and State regulatory policies. Part 4 is an independent analysis that includes cross-indexed references to the more than 60 reports prepared by the Rate Design Study and also to other pertinent sources of information and data. Part 5 summarizes a survey conducted in January 1979 of State commission actions related to the matters contained in Title I of PURPA. Part 6 presents the text of the law. Part 7 is the request from NARUC that prompted the preparation of the Manual. (MCW)« less

Technical note: Design flood under hydrological uncertainty

NASA Astrophysics Data System (ADS)

Botto, Anna; Ganora, Daniele; Claps, Pierluigi; Laio, Francesco

2017-07-01

Planning and verification of hydraulic infrastructures require a design estimate of hydrologic variables, usually provided by frequency analysis, and neglecting hydrologic uncertainty. However, when hydrologic uncertainty is accounted for, the design flood value for a specific return period is no longer a unique value, but is represented by a distribution of values. As a consequence, the design flood is no longer univocally defined, making the design process undetermined. The Uncertainty Compliant Design Flood Estimation (UNCODE) procedure is a novel approach that, starting from a range of possible design flood estimates obtained in uncertain conditions, converges to a single design value. This is obtained through a cost-benefit criterion with additional constraints that is numerically solved in a simulation framework. This paper contributes to promoting a practical use of the UNCODE procedure without resorting to numerical computation. A modified procedure is proposed by using a correction coefficient that modifies the standard (i.e., uncertainty-free) design value on the basis of sample length and return period only. The procedure is robust and parsimonious, as it does not require additional parameters with respect to the traditional uncertainty-free analysis. Simple equations to compute the correction term are provided for a number of probability distributions commonly used to represent the flood frequency curve. The UNCODE procedure, when coupled with this simple correction factor, provides a robust way to manage the hydrologic uncertainty and to go beyond the use of traditional safety factors. With all the other parameters being equal, an increase in the sample length reduces the correction factor, and thus the construction costs, while still keeping the same safety level.

40 CFR Appendix B to Part 60 - Performance Specifications

Code of Federal Regulations, 2012 CFR

2012-07-01

... manufacturers comply with a comprehensive series of design and performance specifications and test procedures to... must periodically select and test an opacity monitor, that is representative of a group of monitors... program are used. One Run may include results for more than one test condition. Constant emissions means...

40 CFR Appendix B to Part 60 - Performance Specifications

Code of Federal Regulations, 2011 CFR

2011-07-01

... manufacturers comply with a comprehensive series of design and performance specifications and test procedures to... must periodically select and test an opacity monitor, that is representative of a group of monitors... program are used. One Run may include results for more than one test condition. Constant emissions means...

40 CFR Appendix B to Part 60 - Performance Specifications

Code of Federal Regulations, 2013 CFR

2013-07-01

... manufacturers comply with a comprehensive series of design and performance specifications and test procedures to... must periodically select and test an opacity monitor, that is representative of a group of monitors... program are used. One Run may include results for more than one test condition. Constant emissions means...

A Qualitative Study Investigating Facility Managers' Perceptions of the Classroom Learning Environment

ERIC Educational Resources Information Center

Parr, Eric Shannon

2017-01-01

Facility managers have the challenge of adhering to community college policies and procedures while fulfilling requirements of administration, students, and teachers concerning specific needs of classroom aesthetics. The role of facility manager and how specific entities affect perceptions of the design and implementation of classroom aesthetics…

The Development of a Vocational Diagnostic Program. Interim Report.

ERIC Educational Resources Information Center

Barnard, William W.

A five-phased project is described which was designed to develop more specific diagnostic procedures and instrumentation that would allow both the vocational counselor and the prospective student to determine more effectively specific occupational programs and occupational objectives for education at the postsecondary level. Phases of the project…

10 CFR 431.401 - Petitions for waiver, and applications for interim waiver, of test procedure.

Code of Federal Regulations, 2013 CFR

2013-01-01

... more design characteristics which prevent testing of the basic model according to the prescribed test... its true energy consumption characteristics as to provide materially inaccurate comparative data. (2... design characteristic(s) constituting the grounds for the petition, and the specific requirements sought...

10 CFR 431.401 - Petitions for waiver, and applications for interim waiver, of test procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... more design characteristics which prevent testing of the basic model according to the prescribed test... its true energy consumption characteristics as to provide materially inaccurate comparative data. (2... design characteristic(s) constituting the grounds for the petition, and the specific requirements sought...

10 CFR 431.401 - Petitions for waiver, and applications for interim waiver, of test procedure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... more design characteristics which prevent testing of the basic model according to the prescribed test... its true energy consumption characteristics as to provide materially inaccurate comparative data. (2... design characteristic(s) constituting the grounds for the petition, and the specific requirements sought...

15 CFR 923.23 - Other areas of particular concern.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Other areas of particular concern. 923... areas of particular concern. (a) The management program may, but is not required to, designate specific... program may include procedures and criteria for designating areas of particular concern for other than...

12 CFR 1815.104 - Specific responsibilities of the designated Fund official.

Code of Federal Regulations, 2010 CFR

2010-01-01

... and maintain working relationships with relevant government agencies (including Federal, state and... standards, procedures, and working relationships for protection and enhancement of environmental quality and...

Field guide for collecting and processing stream-water samples for the National Water-Quality Assessment Program

USGS Publications Warehouse

Shelton, Larry R.

1994-01-01

The U.S. Geological Survey's National Water-Quality Assessment program includes extensive data- collection efforts to assess the quality of the Nations's streams. These studies require analyses of stream samples for major ions, nutrients, sediments, and organic contaminants. For the information to be comparable among studies in different parts of the Nation, consistent procedures specifically designed to produce uncontaminated samples for trace analysis in the laboratory are critical. This field guide describes the standard procedures for collecting and processing samples for major ions, nutrients, organic contaminants, sediment, and field analyses of conductivity, pH, alkalinity, and dissolved oxygen. Samples are collected and processed using modified and newly designed equipment made of Teflon to avoid contamination, including nonmetallic samplers (D-77 and DH-81) and a Teflon sample splitter. Field solid-phase extraction procedures developed to process samples for organic constituent analyses produce an extracted sample with stabilized compounds for more accurate results. Improvements to standard operational procedures include the use of processing chambers and capsule filtering systems. A modified collecting and processing procedure for organic carbon is designed to avoid contamination from equipment cleaned with methanol. Quality assurance is maintained by strict collecting and processing procedures, replicate sampling, equipment blank samples, and a rigid cleaning procedure using detergent, hydrochloric acid, and methanol.

Advanced concentrator panels

NASA Technical Reports Server (NTRS)

Bell, D. M.; Bedard, R. J., Jr.

1981-01-01

The prototype fabrication of a lightweight, high-quality cellular glass substrate reflective panel for use in an advanced point-focusing solar concentrator was completed. The reflective panel is a gore shaped segment of an 11-m paraboloidal dish. The overall concentrator design and the design of the reflective panels are described. prototype-specific panel design modifications are discussed and the fabrication approach and procedure outlined.

Differentiation of ileostomy from colostomy procedures: assessing the accuracy of current procedural terminology codes and the utility of natural language processing.

PubMed

Vo, Elaine; Davila, Jessica A; Hou, Jason; Hodge, Krystle; Li, Linda T; Suliburk, James W; Kao, Lillian S; Berger, David H; Liang, Mike K

2013-08-01

Large databases provide a wealth of information for researchers, but identifying patient cohorts often relies on the use of current procedural terminology (CPT) codes. In particular, studies of stoma surgery have been limited by the accuracy of CPT codes in identifying and differentiating ileostomy procedures from colostomy procedures. It is important to make this distinction because the prevalence of complications associated with stoma formation and reversal differ dramatically between types of stoma. Natural language processing (NLP) is a process that allows text-based searching. The Automated Retrieval Console is an NLP-based software that allows investigators to design and perform NLP-assisted document classification. In this study, we evaluated the role of CPT codes and NLP in differentiating ileostomy from colostomy procedures. Using CPT codes, we conducted a retrospective study that identified all patients undergoing a stoma-related procedure at a single institution between January 2005 and December 2011. All operative reports during this time were reviewed manually to abstract the following variables: formation or reversal and ileostomy or colostomy. Sensitivity and specificity for validation of the CPT codes against the mastery surgery schedule were calculated. Operative reports were evaluated by use of NLP to differentiate ileostomy- from colostomy-related procedures. Sensitivity and specificity for identifying patients with ileostomy or colostomy procedures were calculated for CPT codes and NLP for the entire cohort. CPT codes performed well in identifying stoma procedures (sensitivity 87.4%, specificity 97.5%). A total of 664 stoma procedures were identified by CPT codes between 2005 and 2011. The CPT codes were adequate in identifying stoma formation (sensitivity 97.7%, specificity 72.4%) and stoma reversal (sensitivity 74.1%, specificity 98.7%), but they were inadequate in identifying ileostomy (sensitivity 35.0%, specificity 88.1%) and colostomy (75.2% and 80.9%). NLP performed with greater sensitivity, specificity, and accuracy than CPT codes in identifying stoma procedures and stoma types. Major differences where NLP outperformed CPT included identifying ileostomy (specificity 95.8%, sensitivity 88.3%, and accuracy 91.5%) and colostomy (97.6%, 90.5%, and 92.8%, respectively). CPT codes can identify effectively patients who have had stoma procedures and are adequate in distinguishing between formation and reversal; however, CPT codes cannot differentiate ileostomy from colostomy. NLP can be used to differentiate between ileostomy- and colostomy-related procedures. The role of NLP in conjunction with electronic medical records in data retrieval warrants further investigation. Published by Mosby, Inc.

Specific test and evaluation plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hays, W.H.

1998-03-20

The purpose of this Specific Test and Evaluation Plan (STEP) is to provide a detailed written plan for the systematic testing of modifications made to the 241-AX-B Valve Pit by the W-314 Project. The STEP develops the outline for test procedures that verify the system`s performance to the established Project design criteria. The STEP is a lower tier document based on the W-314 Test and Evaluation Plan (TEP). Testing includes Validations and Verifications (e.g., Commercial Grade Item Dedication activities), Factory Acceptance Tests (FATs), installation tests and inspections, Construction Acceptance Tests (CATs), Acceptance Test Procedures (ATPs), Pre-Operational Test Procedures (POTPs), andmore » Operational Test Procedures (OTPs). It should be noted that POTPs are not required for testing of the transfer line addition. The STEP will be utilized in conjunction with the TEP for verification and validation.« less

Uncovering Procedural Knowledge in Craft, Design, and Technology Education: A Case of Hands-On Activities in Electronics

ERIC Educational Resources Information Center

Pirttimaa, Matti; Husu, Jukka; Metsärinne, Mika

2017-01-01

Different knowledge types have their own specific features and tasks in the learning process. Procedural knowledge is used in craft and technology education when students solve problems individually and share their working knowledge with others. This study presents a detailed analysis of a one student's learning process in technology education and…

Reactive system verification case study: Fault-tolerant transputer communication

NASA Technical Reports Server (NTRS)

Crane, D. Francis; Hamory, Philip J.

1993-01-01

A reactive program is one which engages in an ongoing interaction with its environment. A system which is controlled by an embedded reactive program is called a reactive system. Examples of reactive systems are aircraft flight management systems, bank automatic teller machine (ATM) networks, airline reservation systems, and computer operating systems. Reactive systems are often naturally modeled (for logical design purposes) as a composition of autonomous processes which progress concurrently and which communicate to share information and/or to coordinate activities. Formal (i.e., mathematical) frameworks for system verification are tools used to increase the users' confidence that a system design satisfies its specification. A framework for reactive system verification includes formal languages for system modeling and for behavior specification and decision procedures and/or proof-systems for verifying that the system model satisfies the system specifications. Using the Ostroff framework for reactive system verification, an approach to achieving fault-tolerant communication between transputers was shown to be effective. The key components of the design, the decoupler processes, may be viewed as discrete-event-controllers introduced to constrain system behavior such that system specifications are satisfied. The Ostroff framework was also effective. The expressiveness of the modeling language permitted construction of a faithful model of the transputer network. The relevant specifications were readily expressed in the specification language. The set of decision procedures provided was adequate to verify the specifications of interest. The need for improved support for system behavior visualization is emphasized.

A BPM calibration procedure using TBT data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, M.J.; Crisp, J.; Prieto, P.

2007-06-01

Accurate BPM calibration is crucial for lattice analysis. It is also reassuring when the calibration can be independently verified. This paper outlines a procedure that can extract BPM calibration information from TBT orbit data. The procedure is developed as an extension to the Turn-By-Turn lattice analysis [1]. Its application to data from both Recycler Ring and Main Injector (MI) at Fermilab have produced very encouraging results. Some specifics in hardware design will be mentioned to contrast that of analysis results.

SSL: A software specification language

NASA Technical Reports Server (NTRS)

Austin, S. L.; Buckles, B. P.; Ryan, J. P.

1976-01-01

SSL (Software Specification Language) is a new formalism for the definition of specifications for software systems. The language provides a linear format for the representation of the information normally displayed in a two-dimensional module inter-dependency diagram. In comparing SSL to FORTRAN or ALGOL, it is found to be largely complementary to the algorithmic (procedural) languages. SSL is capable of representing explicitly module interconnections and global data flow, information which is deeply imbedded in the algorithmic languages. On the other hand, SSL is not designed to depict the control flow within modules. The SSL level of software design explicitly depicts intermodule data flow as a functional specification.

Toward the Design of Personalized Continuum Surgical Robots.

PubMed

Morimoto, Tania K; Greer, Joseph D; Hawkes, Elliot W; Hsieh, Michael H; Okamura, Allison M

2018-05-31

Robot-assisted minimally invasive surgical systems enable procedures with reduced pain, recovery time, and scarring compared to traditional surgery. While these improvements benefit a large number of patients, safe access to diseased sites is not always possible for specialized patient groups, including pediatric patients, due to their anatomical differences. We propose a patient-specific design paradigm that leverages the surgeon's expertise to design and fabricate robots based on preoperative medical images. The components of the patient-specific robot design process are a virtual reality design interface enabling the surgeon to design patient-specific tools, 3-D printing of these tools with a biodegradable polyester, and an actuation and control system for deployment. The designed robot is a concentric tube robot, a type of continuum robot constructed from precurved, elastic, nesting tubes. We demonstrate the overall patient-specific design workflow, from preoperative images to physical implementation, for an example clinical scenario: nonlinear renal access to a pediatric kidney. We also measure the system's behavior as it is deployed through real and artificial tissue. System integration and successful benchtop experiments in ex vivo liver and in a phantom patient model demonstrate the feasibility of using a patient-specific design workflow to plan, fabricate, and deploy personalized, flexible continuum robots.

40 CFR 91.404 - Test procedure overview.

Code of Federal Regulations, 2011 CFR

2011-07-01

... to be conducted on an engine dynamometer or equivalent load and speed measurement device. The exhaust... analyzed through the analytical system. (b) The tests are designed to determine the brake-specific...

Ultrasound-Guided Breast Biopsy

MedlinePlus

... the type of biopsy being performed or the design of the biopsy machine, a biopsy of tissue ... cost information. The costs for specific medical imaging tests, treatments and procedures may vary by geographic region. ...

40 CFR 53.9 - Conditions of designation.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-specific standard operating procedure documents shall be readily available to any users. (b) Any method... after delivery and acceptance when maintained and operated in accordance with the manual referred to in...

40 CFR 53.9 - Conditions of designation.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-specific standard operating procedure documents shall be readily available to any users. (b) Any method... after delivery and acceptance when maintained and operated in accordance with the manual referred to in...

Research and emulation of ranging in BPON system

NASA Astrophysics Data System (ADS)

Yang, Guangxiang; Tao, Dexin; He, Yan

2005-12-01

Ranging is one of the key technologies in Broadband Passive Optical Network based on the ATM (BPON) system. It is complex for software designers and difficult to test. In order to simplify the ranging procedure, enhance its efficiency, and find an appropriate method to verify it, a new ranging procedure that completely satisfies the requirements specified in ITU-T G.983.1 and one verifying method is proposed in this paper. A kind of ranging procedure without serial number (SN) searching function, called one-by-one ranging are developed under the condition of cold PON, cold Optical Network Termination (ONU). The ranging procedure includes the use of OLT and ONU flow charts respectively. By using the network emulation software OPNET, the BPON system is modeled and the ranging procedure is simulated. The emulation experimental results show that the presented ranging procedure can effectively eliminate the collision of burst mode signals between ONUs, which can be ranged one-by-one under the controlling of OLT, while also enhancing the ranging efficiency. As all of the message formats used in this research conform with the ITU-T G.983.1, the ranging procedure can meet the protocol specifications with good interoperability, and is very compatible with products of other manufacturer. According to the present study of ranging procedures, guidelines and principles are provided, Also some design difficulties are eliminated in the software design.

Microbial Safari.

ERIC Educational Resources Information Center

Wagner, Stephen C.; Stewart, Robert S., Jr.

2000-01-01

Introduces an investigative microbiology laboratory activity emphasizing critical thinking and experimental design in which students isolate and characterize a bacterium from a specific habitat. Explains the procedures of the laboratory including safety, sample collection, and isolation. (YDS)

Stereotactic (Mammographically Guided) Breast Biopsy

MedlinePlus

... the type of biopsy being performed or the design of the biopsy machine, a biopsy of tissue ... cost information. The costs for specific medical imaging tests, treatments and procedures may vary by geographic region. ...

Optimum design of hybrid phase locked loops

NASA Technical Reports Server (NTRS)

Lee, P.; Yan, T.

1981-01-01

The design procedure of phase locked loops is described in which the analog loop filter is replaced by a digital computer. Specific design curves are given for the step and ramp input changes in phase. It is shown that the designed digital filter depends explicitly on the product of the sampling time and the noise bandwidth of the phase locked loop. This technique of optimization can be applied to the design of digital analog loops for other applications.

Quality assurance procedures for environmental control and monitoring in plant growth facilities. Report of the North Central Regional 101 Committee on Growth Chamber Use

NASA Technical Reports Server (NTRS)

Tibbitts, T. W. (Principal Investigator)

1986-01-01

This report includes procedures for ensuring the quality of the environment provided for plant growth in controlled environment facilities. Biologists and engineers may use these procedures for ensuring quality control during experiments or for ensuring quality control in the design of plant growth facilities. Environmental monitoring prior to and during experiments is included in these procedures. Specific recommendations cover control, acquisition, and calibration for sensor types for the separate parameters of radiation (light), temperature, humidity, carbon dioxide, and air movement.

FORTRAN program for calculating total efficiency - specific speed characteristics of centrifugal compressors

NASA Technical Reports Server (NTRS)

Galvas, M. R.

1972-01-01

A computer program for predicting design point specific speed - efficiency characteristics of centrifugal compressors is presented with instructions for its use. The method permits rapid selection of compressor geometry that yields maximum total efficiency for a particular application. A numerical example is included to demonstrate the selection procedure.

12 CFR 269b.520 - Exceptions to hearing officer's report.

Code of Federal Regulations, 2014 CFR

2014-01-01

... fact and law relied on in support of the position taken on each question, with specific page reference... set forth specifically the questions of procedure, fact, law, or policy to which exceptions are taken...; (3) The exceptions shall designate by precise citation of page the portions of the record relied on...

Systematic Design of a Learning Environment for Domain-Specific and Domain-General Critical Thinking Skills

ERIC Educational Resources Information Center

Tiruneh, Dawit Tibebu; Weldeslassie, Ataklti G.; Kassa, Abrham; Tefera, Zinaye; De Cock, Mieke; Elen, Jan

2016-01-01

Identifying effective instructional approaches that stimulate students' critical thinking (CT) has been the focus of a large body of empirical research. However, there is little agreement on the instructional principles and procedures that are theoretically sound and empirically valid to developing both domain-specific and domain-general CT…

Purdue Plane Structures Analyzer II : a computerized wood engineering system

Treesearch

S. K. Suddarth; R. W. Wolfe

1984-01-01

The Purdue Plane Structures Analyzer (PPSA) is a computer program developed specifically for the analysis of wood structures. It uses recognized analysis procedures, in conjunction with recommendations of the 1982 National Design Specification for Wood Construction, to determine stresses and deflections of wood trusses and frames. The program offers several options for...

Assessing Disease Class-Specific Diagnostic Ability: A Practical Adaptive Test Approach.

ERIC Educational Resources Information Center

Papa, Frank J.; Schumacker, Randall E.

Measures of the robustness of disease class-specific diagnostic concepts could play a central role in training programs designed to assure the development of diagnostic competence. In the pilot study, the authors used disease/sign-symptom conditional probability estimates, Monte Carlo procedures, and artificial intelligence (AI) tools to create…

Measuring Literary Reading Motivation: Questionnaires Design and Pilot Testing

ERIC Educational Resources Information Center

Chrysos, Michail

2017-01-01

This study aims to present the design and pilot testing procedures of the two specific self-report questionnaires were used to measure the two key aspects of reading motivation, self-efficacy and intrinsic motivation in the field of literary (narrative) reading, and the partial factors that jointly shape them. These instruments were outlined in…

Performance and capacity assessment of reinforced concrete bridge piers considering the current load and resistance factor design provisions and plastic hinge length in Kansas : [technical summary].

DOT National Transportation Integrated Search

2014-05-01

Kansas Department of Transportation (KDOT) has implemented the new AASHTO : LRFD provisions in the state specific LRFD design procedure (KDOT-LRFD). There : have been some significant updates in new version of AASHTO-LRFD (2010), compared : to previo...

49 CFR 236.1015 - PTC Safety Plan content requirements and PTC System Certification.

Code of Federal Regulations, 2010 CFR

2010-10-01

... established and can maintain a quality control system for PTC system design and manufacturing acceptable to... an explanation of the design principles and assumptions; (3) A risk assessment of the as-built PTC... the specific procedures and test equipment necessary to ensure the safe and proper installation...

Cognitive Models of Scientific Work and Their Implications for the Design of Knowledge Delivery Systems.

ERIC Educational Resources Information Center

Mavor, A. S.; And Others

Part of a sustained program that has involved the design of personally tailored information systems responsive to the needs of scientists performing common research and teaching tasks, this project focuses on the procedural and content requirements for accomplishing need diagnosis and presents these requirements as specifications for an…

Use of CFD for static sampling hood design: An example for methane flux assessment on landfill surfaces.

PubMed

Lucernoni, Federico; Rizzotto, Matteo; Tapparo, Federica; Capelli, Laura; Sironi, Selena; Busini, Valentina

2016-11-01

The work focuses on the principles for the design of a specific static hood and on the definition of an optimal sampling procedure for the assessment of landfill gas (LFG) surface emissions. This is carried out by means of computational fluid dynamics (CFD) simulations to investigate the fluid dynamics conditions of the hood. The study proves that understanding the fluid dynamic conditions is fundamental in order to understand the sampling results and correctly interpret the measured concentration values by relating them to a suitable LFG emission model, and therefore to estimate emission rates. For this reason, CFD is a useful tool for the design and evaluation of sampling systems, among others, to verify the fundamental hypotheses on which the mass balance for the sampling hood is defined. The procedure here discussed, which is specific for the case of the investigated landfill, can be generalized to be applied also to different scenarios, where hood sampling is involved. Copyright © 2016 Elsevier Ltd. All rights reserved.

User's design handbook for a Standardized Control Module (SCM) for DC to DC Converters, volume 2

NASA Technical Reports Server (NTRS)

Lee, F. C.

1980-01-01

A unified design procedure is presented for selecting the key SCM control parameters for an arbitrarily given power stage configuration and parameter values, such that all regulator performance specifications can be met and optimized concurrently in a single design attempt. All key results and performance indices, for buck, boost, and buck/boost switching regulators which are relevant to SCM design considerations are included to facilitate frequent references.

32 CFR 637.18 - Electronic equipment procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... contain specific authority for the type of equipment to be used, the phone numbers identified as emergency lines and instructions limiting recordings to calls received on the phones so designated. One copy of...

Magnetic Resonance (MR)-Guided Breast Biopsy

MedlinePlus

... the type of biopsy being performed or the design of the biopsy machine, a biopsy of tissue ... cost information. The costs for specific medical imaging tests, treatments and procedures may vary by geographic region. ...

Comparison of Four Teacher Training Procedures in Achieving Teacher and Pupil "Translation" Behaviors in Secondary School Social Studies.

ERIC Educational Resources Information Center

Millett, Gregg B.

A study was designed to determine whether different training procedures could change specific behaviors of 39 intern teachers and their pupils in secondary school social studies classes. Interns were randomly assigned to four training groups each of which received typescripts from the 1953 McCarthy investigations which were to be used the next day…

Using Gagne's theory to teach procedural skills.

PubMed

Buscombe, Charlotte

2013-10-01

Many key medical procedures are performed every day in clinical practice to yield important diagnostic information and to help determine the disease response to intensive treatments. Training clinicians to perform procedures competently and confidently thus carries considerable weight, helping to assure patient safety, the obtainment of adequate samples and minimising patient discomfort. This article considers how Robert Gagne's instructional design model may be effectively used to design lesson plans and teach procedural skills in small group settings. Gagne's model is based upon the information-processing model of mental events that occur when adults are presented with various stimuli. It highlights nine specific instructional events, which correlate with crucial conditions of learning, and are arranged to maximally enhance the learning process, improve session flow and, ultimately, ensure lesson objectives are comprehensively addressed. This article uses the nine points described by Gagne to outline a comprehensive lesson guide for teaching psychomotor skills, using a bone-marrow aspirate procedure as an example. Each of Gagne's instructional events is considered with specific activities for each, and with the variety of activities delineated to meet diverse learning styles. Gagne's instructional events can produce an effective and comprehensive lesson plan for teaching procedural skills, preparing learners with various preferred learning styles to perform psychomotor skills competently in clinical practice. This lesson plan can be of use for both teachers and students across clinical specialties, encouragingly outlining how Gagne's systematic and widely referenced theory can be creatively and practically used. © 2013 John Wiley & Sons Ltd.

Research in mathematical theory of computation. [computer programming applications

NASA Technical Reports Server (NTRS)

Mccarthy, J.

1973-01-01

Research progress in the following areas is reviewed: (1) new version of computer program LCF (logic for computable functions) including a facility to search for proofs automatically; (2) the description of the language PASCAL in terms of both LCF and in first order logic; (3) discussion of LISP semantics in LCF and attempt to prove the correctness of the London compilers in a formal way; (4) design of both special purpose and domain independent proving procedures specifically program correctness in mind; (5) design of languages for describing such proof procedures; and (6) the embedding of ideas in the first order checker.

Control of Technology Transfer at JPL

NASA Technical Reports Server (NTRS)

Oliver, Ronald

2006-01-01

Controlled Technology: 1) Design: preliminary or critical design data, schematics, technical flow charts, SNV code/diagnostics, logic flow diagrams, wirelist, ICDs, detailed specifications or requirements. 2) Development: constraints, computations, configurations, technical analyses, acceptance criteria, anomaly resolution, detailed test plans, detailed technical proposals. 3) Production: process or how-to: assemble, operated, repair, maintain, modify. 4) Manufacturing: technical instructions, specific parts, specific materials, specific qualities, specific processes, specific flow. 5) Operations: how-to operate, contingency or standard operating plans, Ops handbooks. 6) Repair: repair instructions, troubleshooting schemes, detailed schematics. 7) Test: specific procedures, data, analysis, detailed test plan and retest plans, detailed anomaly resolutions, detailed failure causes and corrective actions, troubleshooting, trended test data, flight readiness data. 8) Maintenance: maintenance schedules and plans, methods for regular upkeep, overhaul instructions. 9) Modification: modification instructions, upgrades kit parts, including software

Project W-314 specific test and evaluation plan for AZ tank farm upgrades

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hays, W.H.

1998-08-12

The purpose of this Specific Test and Evaluation Plan (STEP) is to provide a detailed written plan for the systematic testing of modifications made by the addition of the SN-631 transfer line from the AZ-O1A pit to the AZ-02A pit by the W-314 Project. The STEP develops the outline for test procedures that verify the system`s performance to the established Project design criteria. The STEP is a lower tier document based on the W-314 Test and Evaluation P1 an (TEP). Testing includes Validations and Verifications (e.g., Commercial Grade Item Dedication activities, etc), Factory Tests and Inspections (FTIs), installation tests andmore » inspections, Construction Tests and Inspections (CTIs), Acceptance Test Procedures (ATPs), Pre-Operational Test Procedures (POTPs), and Operational Test Procedures (OTPs). The STEP will be utilized in conjunction with the TEP for verification and validation.« less

Integration of the Response Surface Methodology with the Compromise Decision Support Problem in Developing a General Robust Design Procedure

NASA Technical Reports Server (NTRS)

Chen, Wei; Tsui, Kwok-Leung; Allen, Janet K.; Mistree, Farrokh

1994-01-01

In this paper we introduce a comprehensive and rigorous robust design procedure to overcome some limitations of the current approaches. A comprehensive approach is general enough to model the two major types of robust design applications, namely, robust design associated with the minimization of the deviation of performance caused by the deviation of noise factors (uncontrollable parameters), and robust design due to the minimization of the deviation of performance caused by the deviation of control factors (design variables). We achieve mathematical rigor by using, as a foundation, principles from the design of experiments and optimization. Specifically, we integrate the Response Surface Method (RSM) with the compromise Decision Support Problem (DSP). Our approach is especially useful for design problems where there are no closed-form solutions and system performance is computationally expensive to evaluate. The design of a solar powered irrigation system is used as an example. Our focus in this paper is on illustrating our approach rather than on the results per se.

Chapter 12: Survey Design and Implementation for Estimating Gross Savings Cross-Cutting Protocol. The Uniform Methods Project: Methods for Determining Energy Efficiency Savings for Specific Measures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurnik, Charles W; Baumgartner, Robert

This chapter presents an overview of best practices for designing and executing survey research to estimate gross energy savings in energy efficiency evaluations. A detailed description of the specific techniques and strategies for designing questions, implementing a survey, and analyzing and reporting the survey procedures and results is beyond the scope of this chapter. So for each topic covered below, readers are encouraged to consult articles and books cited in References, as well as other sources that cover the specific topics in greater depth. This chapter focuses on the use of survey methods to collect data for estimating gross savingsmore » from energy efficiency programs.« less

10 CFR 70.39 - Specific licenses for the manufacture or initial transfer of calibration or reference sources.

Code of Federal Regulations, 2011 CFR

2011-01-01

... and design; (iii) Details of the method of incorporation and binding of the plutonium in the source; (iv) Procedures for and results of prototype testing of sources, which are designed to contain more... experimental studies and tests, required by the Commission to facilitate a determination of the safety of the...

SIMS prototype system 1: Design data brochure. [solar heating system

NASA Technical Reports Server (NTRS)

1978-01-01

A prototype solar heating and hot water system using air as the collector fluid and a pebble bed for heat storage was designed for installation into a single family dwelling. The system, subsystem, and installation requirements are described. System operation and performance are discussed, and procedures for sizing the system to a specific site are presented.

19 CFR 4.86 - Intercoastal residue-cargo procedure; optional ports.

Code of Federal Regulations, 2010 CFR

2010-04-01

... agent is unable at that time to designate the specific port or ports of discharge of that residue cargo... ports, Great Lakes coast,” as the case may be. The traveling manifest shall be similarly noted. Upon arrival of the vessel at the first port on the next coast, the master, owner, or agent must designate the...

16 CFR 1500.89 - Procedures and requirements for determinations regarding lead content of materials or products...

Code of Federal Regulations, 2011 CFR

2011-01-01

... Product Safety Improvement Act provides for specific lead limits in children's products. Section 101(a) of the CPSIA provides that by February 10, 2009, products designed or intended primarily for children 12... designed or intended primarily for children 12 years of age or younger cannot contain more than 300 ppm of...

System design package for SIMS prototype system 4, solar heating and domestic hot water

NASA Technical Reports Server (NTRS)

1978-01-01

The system consisted of a modular designed prepackaged solar unit, containing solar collectors, a rock storage container, blowers, dampers, ducting, air-to-water heat exchanger, DHW preheat tank, piping, and system controls. The system was designed to be installed adjacent to a small single family dwelling. The description, performance specification, subsystem drawings, verification plan/procedure, and hazard analysis of the system were packaged for evaluation.

Design and construction of the MicroBooNE detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Acciarri, R.; Adams, C.; An, R.

This paper describes the design and construction of the MicroBooNE liquid argon time projection chamber and associated systems. MicroBooNE is the first phase of the Short Baseline Neutrino program, located at Fermilab, and will utilize the capabilities of liquid argon detectors to examine a rich assortment of physics topics. In this document details of design specifications, assembly procedures, and acceptance tests are reported.

Calculation and design of a ramjet missile

NASA Astrophysics Data System (ADS)

Schubert, Johannes

The fundamentals for the design of a ramjet missile are treated. The chemical fundamentals of the solid rocket propellants used for ramjet missiles are outlined. The determination of the most favorable flying speed is discussed. The thermodynamic fundamentals (calculation of the solid propellant missile, calculation of the mixing procedure and the after burning in the pressure nozzle, and power calculation) are presented. The design specifications of the propulsion system are given.

Design and construction of the MicroBooNE detector

DOE PAGES

Acciarri, R.; Adams, C.; An, R.; ...

2017-02-01

This paper describes the design and construction of the MicroBooNE liquid argon time projection chamber and associated systems. MicroBooNE is the first phase of the Short Baseline Neutrino program, located at Fermilab, and will utilize the capabilities of liquid argon detectors to examine a rich assortment of physics topics. In this document details of design specifications, assembly procedures, and acceptance tests are reported.

Integration of dynamic, aerodynamic, and structural optimization of helicopter rotor blades

NASA Technical Reports Server (NTRS)

Peters, David A.

1991-01-01

Summarized here is the first six years of research into the integration of structural, dynamic, and aerodynamic considerations in the design-optimization process for rotor blades. Specifically discussed here is the application of design optimization techniques for helicopter rotor blades. The reduction of vibratory shears and moments at the blade root, aeroelastic stability of the rotor, optimum airframe design, and an efficient procedure for calculating system sensitivities with respect to the design variables used are discussed.

Technical standards and guidelines: molecular genetic testing for ultra-rare disorders.

PubMed

Maddalena, Anne; Bale, Sherri; Das, Soma; Grody, Wayne; Richards, Sue

2005-10-01

These standards and guidelines are designed primarily as an educational resource for clinical laboratory geneticists to help them provide quality clinical laboratory genetic services. Adherence to these standards and guidelines does not necessarily ensure a successful medical outcome. These standards and guidelines should not be considered inclusive of all proper procedures and tests or exclusive of other procedures and tests that are reasonably directed to obtaining the same results. In determining the propriety of any specific procedure or test, the clinical molecular geneticist should apply his or her own professional judgment to the specific clinical circumstances presented by the individual patient or specimen. It may be prudent, however, to document in the laboratory record the rationale for any significant deviation from these standards and guidelines.

The J3 SCR model applied to resonant converter simulation

NASA Technical Reports Server (NTRS)

Avant, R. L.; Lee, F. C. Y.

1985-01-01

The J3 SCR model is a continuous topology computer model for the SCR. Its circuit analog and parameter estimation procedure are uniformly applicable to popular computer-aided design and analysis programs such as SPICE2 and SCEPTRE. The circuit analog is based on the intrinsic three pn junction structure of the SCR. The parameter estimation procedure requires only manufacturer's specification sheet quantities as a data base.

An alternative method to amplify RNA without loss of signal conservation for expression analysis with a proteinase DNA microarray in the ArrayTube format.

PubMed

Schüler, Susann; Wenz, Ingrid; Wiederanders, B; Slickers, P; Ehricht, R

2006-06-12

Recent developments in DNA microarray technology led to a variety of open and closed devices and systems including high and low density microarrays for high-throughput screening applications as well as microarrays of lower density for specific diagnostic purposes. Beside predefined microarrays for specific applications manufacturers offer the production of custom-designed microarrays adapted to customers' wishes. Array based assays demand complex procedures including several steps for sample preparation (RNA extraction, amplification and sample labelling), hybridization and detection, thus leading to a high variability between several approaches and resulting in the necessity of extensive standardization and normalization procedures. In the present work a custom designed human proteinase DNA microarray of lower density in ArrayTube format was established. This highly economic open platform only requires standard laboratory equipment and allows the study of the molecular regulation of cell behaviour by proteinases. We established a procedure for sample preparation and hybridization and verified the array based gene expression profile by quantitative real-time PCR (QRT-PCR). Moreover, we compared the results with the well established Affymetrix microarray. By application of standard labelling procedures with e.g. Klenow fragment exo-, single primer amplification (SPA) or In Vitro Transcription (IVT) we noticed a loss of signal conservation for some genes. To overcome this problem we developed a protocol in accordance with the SPA protocol, in which we included target specific primers designed individually for each spotted oligomer. Here we present a complete array based assay in which only the specific transcripts of interest are amplified in parallel and in a linear manner. The array represents a proof of principle which can be adapted to other species as well. As the designed protocol for amplifying mRNA starts from as little as 100 ng total RNA, it presents an alternative method for detecting even low expressed genes by microarray experiments in a highly reproducible and sensitive manner. Preservation of signal integrity is demonstrated out by QRT-PCR measurements. The little amounts of total RNA necessary for the analyses make this method applicable for investigations with limited material as in clinical samples from, for example, organ or tumour biopsies. Those are arguments in favour of the high potential of our assay compared to established procedures for amplification within the field of diagnostic expression profiling. Nevertheless, the screening character of microarray data must be mentioned, and independent methods should verify the results.

Model of Procedure Usage – Results from a Qualitative Study to Inform Design of Computer-Based Procedures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johanna H Oxstrand; Katya L Le Blanc

The nuclear industry is constantly trying to find ways to decrease the human error rate, especially the human errors associated with procedure use. As a step toward the goal of improving procedure use performance, researchers, together with the nuclear industry, have been looking at replacing the current paper-based procedures with computer-based procedure systems. The concept of computer-based procedures is not new by any means; however most research has focused on procedures used in the main control room. Procedures reviewed in these efforts are mainly emergency operating procedures and normal operating procedures. Based on lessons learned for these previous efforts wemore » are now exploring a more unknown application for computer based procedures - field procedures, i.e. procedures used by nuclear equipment operators and maintenance technicians. The Idaho National Laboratory, the Institute for Energy Technology, and participants from the U.S. commercial nuclear industry are collaborating in an applied research effort with the objective of developing requirements and specifications for a computer-based procedure system to be used by field operators. The goal is to identify the types of human errors that can be mitigated by using computer-based procedures and how to best design the computer-based procedures to do this. The underlying philosophy in the research effort is “Stop – Start – Continue”, i.e. what features from the use of paper-based procedures should we not incorporate (Stop), what should we keep (Continue), and what new features or work processes should be added (Start). One step in identifying the Stop – Start – Continue was to conduct a baseline study where affordances related to the current usage of paper-based procedures were identified. The purpose of the study was to develop a model of paper based procedure use which will help to identify desirable features for computer based procedure prototypes. Affordances such as note taking, markups, sharing procedures between fellow coworkers, the use of multiple procedures at once, etc. were considered. The model describes which affordances associated with paper based procedures should be transferred to computer-based procedures as well as what features should not be incorporated. The model also provides a means to identify what new features not present in paper based procedures need to be added to the computer-based procedures to further enhance performance. The next step is to use the requirements and specifications to develop concepts and prototypes of computer-based procedures. User tests and other data collection efforts will be conducted to ensure that the real issues with field procedures and their usage are being addressed and solved in the best manner possible. This paper describes the baseline study, the construction of the model of procedure use, and the requirements and specifications for computer-based procedures that were developed based on the model. It also addresses how the model and the insights gained from it were used to develop concepts and prototypes for computer based procedures.« less

Definition of Specific Functions and Procedural Skills Required by Cuban Specialists in Intensive Care and Emergency Medicine.

PubMed

Véliz, Pedro L; Berra, Esperanza M; Jorna, Ana R

2015-07-01

INTRODUCTION Medical specialties' core curricula should take into account functions to be carried out, positions to be filled and populations to be served. The functions in the professional profile for specialty training of Cuban intensive care and emergency medicine specialists do not include all the activities that they actually perform in professional practice. OBJECTIVE Define the specific functions and procedural skills required of Cuban specialists in intensive care and emergency medicine. METHODS The study was conducted from April 2011 to September 2013. A three-stage methodological strategy was designed using qualitative techniques. By purposive maximum variation sampling, 82 professionals were selected. Documentary analysis and key informant criteria were used in the first stage. Two expert groups were formed in the second stage: one used various group techniques (focus group, oral and written brainstorming) and the second used a three-round Delphi method. In the final stage, a third group of experts was questioned in semistructured in-depth interviews, and a two-round Delphi method was employed to assess priorities. RESULTS Ultimately, 78 specific functions were defined: 47 (60.3%) patient care, 16 (20.5%) managerial, 6 (7.7%) teaching, and 9 (11.5%) research. Thirty-one procedural skills were identified. The specific functions and procedural skills defined relate to the profession's requirements in clinical care of the critically ill, management of patient services, teaching and research at the specialist's different occupational levels. CONCLUSIONS The specific functions and procedural skills required of intensive care and emergency medicine specialists were precisely identified by a scientific method. This product is key to improving the quality of teaching, research, administration and patient care in this specialty in Cuba. The specific functions and procedural skills identified are theoretical, practical, methodological and social contributions to inform future curricular reform and to help intensive care specialists enhance their performance in comprehensive patient care. KEYWORDS Intensive care, urgent care, emergency medicine, continuing medical education, curriculum, diagnostic techniques and procedures, medical residency, Cuba.

ANSI/AIAA S-081A, Pressure Vessel Standards Implementation Guidelines

NASA Technical Reports Server (NTRS)

Greene, Nathanael J.

2009-01-01

The stress rupture specification for Composite Overwrapped Pressure Vessels (COPV) is discussed. The composite shell of the COPV shall be designed to meet the design life considering the time it is under sustained load. A Mechcanical Damage Control Plan (MDCP) shall be created and implemented that assures the COPV will not fail due to mechanical damage due to manufacturing, testing, shipping, installation, or flight. Proven processes and procedures for fabrication and repair shall be used to preclude damage or material degradation during material processing, manufacturing operations, and refurbushment.Selected NDI techniques for the liner and/or boss(es) shall be performed before overwrapping with composite. When visual inspection reveals mechanical damage or defects exceeding manufacturing specification levels (and standard repair procedures), the damaged COPV shall be submitted to a material review board (MRB) for disposition. Every COPV shall be subjected to visual and other non-destructive inspection (NDI), per the inspection plan.

Computational redesign of a protein-protein interface for high affinity and binding specificity using modular architecture and naturally occurring template fragments.

PubMed

Potapov, V; Reichmann, D; Abramovich, R; Filchtinski, D; Zohar, N; Ben Halevy, D; Edelman, M; Sobolev, V; Schreiber, G

2008-12-05

A new method is presented for the redesign of protein-protein interfaces, resulting in specificity of the designed pair while maintaining high affinity. The design is based on modular interface architecture and was carried out on the interaction between TEM1 beta-lactamase and its inhibitor protein, beta-lactamase inhibitor protein. The interface between these two proteins is composed of several mostly independent modules. We previously showed that it is possible to delete a complete module without affecting the overall structure of the interface. Here, we replace a complete module with structure fragments taken from nonrelated proteins. Nature-optimized fragments were chosen from 10(7) starting templates found in the Protein Data Bank. A procedure was then developed to identify sets of interacting template residues with a backbone arrangement mimicking the original module. This generated a final list of 361 putative replacement modules that were ranked using a novel scoring function based on grouped atom-atom contact surface areas. The top-ranked designed complex exhibited an affinity of at least the wild-type level and a mode of binding that was remarkably specific despite the absence of negative design in the procedure. In retrospect, the combined application of three factors led to the success of the design approach: utilizing the modular construction of the interface, capitalizing on native rather than artificial templates, and ranking with an accurate atom-atom contact surface scoring function.

Certification of highly complex safety-related systems.

PubMed

Reinert, D; Schaefer, M

1999-01-01

The BIA has now 15 years of experience with the certification of complex electronic systems for safety-related applications in the machinery sector. Using the example of machining centres this presentation will show the systematic procedure for verifying and validating control systems using Application Specific Integrated Circuits (ASICs) and microcomputers for safety functions. One section will describe the control structure of machining centres with control systems using "integrated safety." A diverse redundant architecture combined with crossmonitoring and forced dynamization is explained. In the main section the steps of the systematic certification procedure are explained showing some results of the certification of drilling machines. Specification reviews, design reviews with test case specification, statistical analysis, and walk-throughs are the analytical measures in the testing process. Systematic tests based on the test case specification, Electro Magnetic Interference (EMI), and environmental testing, and site acceptance tests on the machines are the testing measures for validation. A complex software driven system is always undergoing modification. Most of the changes are not safety-relevant but this has to be proven. A systematic procedure for certifying software modifications is presented in the last section of the paper.

Design optimization of axial flow hydraulic turbine runner: Part II - multi-objective constrained optimization method

NASA Astrophysics Data System (ADS)

Peng, Guoyi; Cao, Shuliang; Ishizuka, Masaru; Hayama, Shinji

2002-06-01

This paper is concerned with the design optimization of axial flow hydraulic turbine runner blade geometry. In order to obtain a better design plan with good performance, a new comprehensive performance optimization procedure has been presented by combining a multi-variable multi-objective constrained optimization model with a Q3D inverse computation and a performance prediction procedure. With careful analysis of the inverse design of axial hydraulic turbine runner, the total hydraulic loss and the cavitation coefficient are taken as optimization objectives and a comprehensive objective function is defined using the weight factors. Parameters of a newly proposed blade bound circulation distribution function and parameters describing positions of blade leading and training edges in the meridional flow passage are taken as optimization variables.The optimization procedure has been applied to the design optimization of a Kaplan runner with specific speed of 440 kW. Numerical results show that the performance of designed runner is successfully improved through optimization computation. The optimization model is found to be validated and it has the feature of good convergence. With the multi-objective optimization model, it is possible to control the performance of designed runner by adjusting the value of weight factors defining the comprehensive objective function. Copyright

Design definition study of a lift/cruise fan technology V/STOL airplane: Summary

NASA Technical Reports Server (NTRS)

Zabinsky, J. M.; Higgins, H. C.

1975-01-01

A two-engine three-fan V/STOL airplane was designed to fulfill naval operational requirements. A multimission airplane was developed from study of specific point designs. Based on the multimission concept, airplanes were designed to demonstrate and develop the technology and operational procedures for this class of aircraft. Use of interconnected variable pitch fans led to a good balance between high thrust with responsive control and efficient thrust at cruise speeds. The airplanes and their characteristics are presented.

Instrumentation and data analysis design for evaluating mechanic performance in decentralized I/M programs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ashby, H.A.; Carlson, T.R.; Husson, L.

1986-01-01

Significant reductions in motor vehicle emissions are possible through the implementation of inspection and maintenance (I/M) programs. However, the potential benefits of I/M are obviously not achieved when specific inspection requirements are ignored or improperly performed. In addition, I/M benefits may be substantially reduced when improper repair procedures are used on vehicles which fail the test. In order for the ''theoretical'' benefits of I/M to be achieved, certain program design and enforcement procedures are necessary. The use of instrumentation and data analysis methods capable of identifying individuals who are improperly performing inspections and repairs is critical.

Optimization of wearable microwave antenna with simplified electromagnetic model of the human body

NASA Astrophysics Data System (ADS)

Januszkiewicz, Łukasz; Barba, Paolo Di; Hausman, Sławomir

2017-12-01

In this paper the problem of optimization design of a microwave wearable antenna is investigated. Reference is made to a specific antenna design that is a wideband Vee antenna the geometry of which is characterized by 6 parameters. These parameters were automatically adjusted with an evolution strategy based algorithm EStra to obtain the impedance matching of the antenna located in the proximity of the human body. The antenna was designed to operate in the ISM (industrial, scientific, medical) band which covers the frequency range of 2.4 GHz up to 2.5 GHz. The optimization procedure used the finite-difference time-domain method based full-wave simulator with a simplified human body model. In the optimization procedure small movements of antenna towards or away of the human body that are likely to happen during real use were considered. The stability of the antenna parameters irrespective of the movements of the user's body is an important factor in wearable antenna design. The optimization procedure allowed obtaining good impedance matching for a given range of antenna distances with respect to the human body.

Mechanization of library procedures in the medium-sized medical library. 8. Computer applications in hospital departmental libraries.

PubMed

Howard, E; Kharibian, G

1972-07-01

To test the hypothesis that a standard library system could be designed for hospital departmental libraries, a system was developed and partially tested for four departmental libraries in the Washington University School of Medicine and Associated Hospitals. The system from determination of needs through design and evaluation, is described. The system was limited by specific constraints to control of the monograph collection. Products of control include catalog cards, accessions list, new book list, location list, fund list, missing book list, and discard book list. Sample data form and pages from a procedure manual are given, and conversion from a manual to an automated system is outlined. The question of standardization of library records and procedures is discussed, with indications of the way in which modular design, as utilized in this system, could contribute to greater flexibility in design of future systems. Reference is made to anticipating needs for organizing departmental libraries in developing regional medical library programs and to exploring the role of the departmental library in a medical library network.

29 CFR 102.46 - Exceptions, cross-exceptions, briefs, answering briefs; time for filing; where to file; service...

Code of Federal Regulations, 2010 CFR

2010-07-01

... support of the position taken on each question, with specific page reference to the record and the legal... set forth specifically the questions of procedure, fact, law, or policy to which exception is taken...; (iii) shall designate by precise citation of page the portions of the record relied on; and (iv) shall...

29 CFR 102.46 - Exceptions, cross-exceptions, briefs, answering briefs; time for filing; where to file; service...

Code of Federal Regulations, 2011 CFR

2011-07-01

... support of the position taken on each question, with specific page reference to the record and the legal... set forth specifically the questions of procedure, fact, law, or policy to which exception is taken...; (iii) shall designate by precise citation of page the portions of the record relied on; and (iv) shall...

Acquisition Handbook - Update. Comprehensive Approach to Reusable Defensive Software (CARDS)

DTIC Science & Technology

1994-03-25

designs, and implementation components (source code, test plans, procedures and results, and system/software documentation). This handbook provides a...activities where software components are acquired, evaluated, tested and sometimes modified. In addition to serving as a facility for the acquisition and...systems from such components [1]. Implementation components are at the lowest level and consist of: specifications; detailed designs; code, test

Robotic-assisted surgery in ophthalmology.

PubMed

de Smet, Marc D; Naus, Gerrit J L; Faridpooya, Koorosh; Mura, Marco

2018-05-01

Provide an overview of the current landscape of robotics in ophthalmology, including the pros and cons of system designs, the clinical development path, and the likely future direction of the field. Robots designed for eye surgery should meet certain basic requirements. Three designs are currently being developed: smart surgical tools such as the steady hand, comanipulation devices and telemanipulators using either a fixed or virtual remote center of motion. Successful human intraocular surgery is being performed using the Preceyes surgical system. Another telemanipulation robot, the da Vinci Surgical System, has been used to perform a pterygium repair in humans and was successful in ex-vivo corneal surgery despite its nonophthalmic design. Apart from Preceyes' BV research platform, none of the currently eye-specific systems has reached a commercial stage. Systems are likely to evolve from robotic assistance during specific procedural steps to semiautonomous surgery, as smart sensors are introduced to enhance the basic functionalities of robotic systems. Robotics is still in its infancy in ophthalmology but is rapidly reaching a stage wherein it will be introduced into everyday ophthalmic practice. It will most likely be introduced first for demanding vitreo-retinal procedures, followed by anterior segment applications.

Species-specific diagnostic assays for Bonamia ostreae and B. exitiosa in European flat oyster Ostrea edulis: conventional, real-time and multiplex PCR.

PubMed

Ramilo, Andrea; Navas, J Ignacio; Villalba, Antonio; Abollo, Elvira

2013-05-27

Bonamia ostreae and B. exitiosa have caused mass mortalities of various oyster species around the world and co-occur in some European areas. The World Organisation for Animal Health (OIE) has included infections with both species in the list of notifiable diseases. However, official methods for species-specific diagnosis of either parasite have certain limitations. In this study, new species-specific conventional PCR (cPCR) and real-time PCR techniques were developed to diagnose each parasite species. Moreover, a multiplex PCR method was designed to detect both parasites in a single assay. The analytical sensitivity and specificity of each new method were evaluated. These new procedures were compared with 2 OIE-recommended methods, viz. standard histology and PCR-RFLP. The new procedures showed higher sensitivity than the OIE recommended ones for the diagnosis of both species. The sensitivity of tests with the new primers was higher using oyster gills and gonad tissue, rather than gills alone. The lack of a 'gold standard' prevented accurate estimation of sensitivity and specificity of the new methods. The implementation of statistical tools (maximum likelihood method) for the comparison of the diagnostic tests showed the possibility of false positives with the new procedures, although the absence of a gold standard precluded certainty. Nevertheless, all procedures showed negative results when used for the analysis of oysters from a Bonamia-free area.

49 CFR 179.7 - Quality assurance program.

Code of Federal Regulations, 2010 CFR

2010-10-01

... means to detect any nonconformity in the manufacturing, repair, inspection, testing, and qualification... quality control personnel. (3) Procedures to ensure that the latest applicable drawings, design calculations, specifications, and instructions are used in manufacture, inspection, testing, and repair. (4...

Fiscal year 1980-81 implementation plan in support of technical development and integration of sampling and aggregation procedures. [crop acreage estimation

NASA Technical Reports Server (NTRS)

1981-01-01

The specific objectives of the FY 1980-81 tasks are: (1) further refinements to the weighted aggregation procedure; (2) improved approaches for estimating within-stratum variance; (3) more intensive investigation of alternative sampling strategies such as full-frame sampling strategy, and (4) further developments in regard to a simulated approach for assessing the performance of the overall designed sampling and aggregation system.

Multiparameter optimization of mammography: an update

NASA Astrophysics Data System (ADS)

Jafroudi, Hamid; Muntz, E. P.; Jennings, Robert J.

1994-05-01

Previously in this forum we have reported the application of multiparameter optimization techniques to the design of a minimum dose mammography system. The approach used a reference system to define the physical imaging performance required and the dose to which the dose for the optimized system should be compared. During the course of implementing the resulting design in hardware suitable for laboratory testing, the state of the art in mammographic imaging changed, so that the original reference system, which did not have a grid, was no longer appropriate. A reference system with a grid was selected in response to this change, and at the same time the optimization procedure was modified, to make it more general and to facilitate study of the optimized design under a variety of conditions. We report the changes in the procedure, and the results obtained using the revised procedure and the up- to-date reference system. Our results, which are supported by laboratory measurements, indicate that the optimized design can image small objects as well as the reference system using only about 30% of the dose required by the reference system. Hardware meeting the specification produced by the optimization procedure and suitable for clinical use is currently under evaluation in the Diagnostic Radiology Department at the Clinical Center, NH.

Normalization of urinary drug concentrations with specific gravity and creatinine.

PubMed

Cone, Edward J; Caplan, Yale H; Moser, Frank; Robert, Tim; Shelby, Melinda K; Black, David L

2009-01-01

Excessive fluid intake can substantially dilute urinary drug concentrations and result in false-negative reports for drug users. Methods for correction ("normalization") of drug/metabolite concentrations in urine have been utilized by anti-doping laboratories, pain monitoring programs, and in environmental monitoring programs to compensate for excessive hydration, but such procedures have not been used routinely in workplace, legal, and treatment settings. We evaluated two drug normalization procedures based on specific gravity and creatinine. These corrections were applied to urine specimens collected from three distinct groups (pain patients, heroin users, and marijuana/ cocaine users). Each group was unique in characteristics, study design, and dosing conditions. The results of the two normalization procedures were highly correlated (r=0.94; range, 0.78-0.99). Increases in percent positives by specific gravity and creatinine normalization were small (0.3% and -1.0%, respectively) for heroin users (normally hydrated subjects), modest (4.2-9.8%) for pain patients (unknown hydration state), and substantial (2- to 38-fold increases) for marijuana/cocaine users (excessively hydrated subjects). Despite some limitations, these normalization procedures provide alternative means of dealing with highly dilute, dilute, and concentrated urine specimens. Drug/metabolite concentration normalization by these procedures is recommended for urine testing programs, especially as a means of coping with dilute specimens.

4MOST systems engineering: from conceptual design to preliminary design review

NASA Astrophysics Data System (ADS)

Bellido-Tirado, Olga; Frey, Steffen; Barden, Samuel C.; Brynnel, Joar; Giannone, Domenico; Haynes, Roger; de Jong, Roelof S.; Phillips, Daniel; Schnurr, Olivier; Walcher, Jakob; Winkler, Roland

2016-08-01

The 4MOST Facility is a high-multiplex, wide-field, brief-fed spectrograph system for the ESO VISTA telescope. It aims to create a world-class spectroscopic survey facility unique in its combination of wide-field multiplex, spectral resolution, spectral coverage, and sensitivity. At the end of 2014, after a successful concept optimization design phase, 4MOST entered into its Preliminary Design Phase. Here we present the process and tools adopted during the Preliminary Design Phase to define the subsystems specifications, coordinate the interface control documents and draft the system verification procedures.

Enriching peptide libraries for binding affinity and specificity through computationally directed library design

PubMed Central

Foight, Glenna Wink; Chen, T. Scott; Richman, Daniel; Keating, Amy E.

2017-01-01

Peptide reagents with high affinity or specificity for their target protein interaction partner are of utility for many important applications. Optimization of peptide binding by screening large libraries is a proven and powerful approach. Libraries designed to be enriched in peptide sequences that are predicted to have desired affinity or specificity characteristics are more likely to yield success than random mutagenesis. We present a library optimization method in which the choice of amino acids to encode at each peptide position can be guided by available experimental data or structure-based predictions. We discuss how to use analysis of predicted library performance to inform rounds of library design. Finally, we include protocols for more complex library design procedures that consider the chemical diversity of the amino acids at each peptide position and optimize a library score based on a user-specified input model. PMID:28236241

Enriching Peptide Libraries for Binding Affinity and Specificity Through Computationally Directed Library Design.

PubMed

Foight, Glenna Wink; Chen, T Scott; Richman, Daniel; Keating, Amy E

2017-01-01

Peptide reagents with high affinity or specificity for their target protein interaction partner are of utility for many important applications. Optimization of peptide binding by screening large libraries is a proven and powerful approach. Libraries designed to be enriched in peptide sequences that are predicted to have desired affinity or specificity characteristics are more likely to yield success than random mutagenesis. We present a library optimization method in which the choice of amino acids to encode at each peptide position can be guided by available experimental data or structure-based predictions. We discuss how to use analysis of predicted library performance to inform rounds of library design. Finally, we include protocols for more complex library design procedures that consider the chemical diversity of the amino acids at each peptide position and optimize a library score based on a user-specified input model.

Functional and Therapeutic Indications of Liposuction: Personal Experience and Review of the Literature.

PubMed

Atiyeh, Bishara; Costagliola, Michel; Illouz, Yves-Gerard; Dibo, Saad; Zgheib, Elias; Rampillon, Florence

2015-08-01

Liposuction is the most common cosmetic surgical procedure worldwide. It has evolved from being designed primarily for body contouring to becoming essential adjunct to various other aesthetic procedures, greatly enhancing their outcome. Despite its hard clear differentiation between an aesthetic and therapeutic indication for some pathologic conditions, liposuction has been increasingly applied to a gamut of disorders as a therapeutic tool or to improve function. In fact, liposuction has ceased to define a specific procedure and became synonymous to a surgical technique or tool same as the surgical knife, laser, electrocautery, suture material, or even wound-dressing products. At present, there seems to be an enormous potential for the application of the basic liposuction technique in ablative and reconstructive surgery outside the realm of purely aesthetic procedures. The present review contemplates the various nonaesthetic applications of liposuction, displaying the enormous potentials of what should be considered a basic surgical technique rather than a specific aesthetic procedure. Implications of this new definition of liposuction should induce third-party public payers and insurance companies to reconsider their remuneration and reimbursement policies.

Empirical models for use in designing decompression procedures for space operations

NASA Technical Reports Server (NTRS)

Conkin, Johnny; Edwards, Benjamin F.; Waligora, James M.; Horrigan, David J., Jr.

1987-01-01

Empirical models for predicting the incidence of Type 1 altitude decompression sickness (DCS) and venous gas emboli (VGE) during space extravehicular activity (EVA), and for use in designing safe denitrogenation decompression procedures are developed. The models are parameterized using DCS and VGE incidence data from NASA and USAF manned altitude chamber decompression tests using 607 male and female subject tests. These models, and procedures for their use, consist of: (1) an exponential relaxation model and procedure for computing tissue nitrogen partial pressure resulting from a specified prebreathing and stepped decompression sequence; (2) a formula for calculating Tissue Ratio (TR), a tissue decompression stress index; (3) linear and Hill equation models for predicting the total incidence of VGE and DCS attendant with a particular TR; (4) graphs of cumulative DCS and VGE incidence (risk) versus EVA exposure time at any specified TR; and (5) two equations for calculating the average delay period for the initial detection of VGE or indication of Type 1 DCS in a group after a specific denitrogenation decompression procedure. Several examples of realistic EVA preparations are provided.

AgRISTARS: Foreign commodity production forecasting. Corn/soybean decision logic development and testing

NASA Technical Reports Server (NTRS)

Dailey, C. L.; Abotteen, K. M. (Principal Investigator)

1980-01-01

The development and testing of an analysis procedure which was developed to improve the consistency and objectively of crop identification using Landsat data is described. The procedure was developed to identify corn and soybean crops in the U.S. corn belt region. The procedure consists of a series of decision points arranged in a tree-like structure, the branches of which lead an analyst to crop labels. The specific decision logic is designed to maximize the objectively of the identification process and to promote the possibility of future automation. Significant results are summarized.

A web-based procedure for liver segmentation in CT images

NASA Astrophysics Data System (ADS)

Yuan, Rong; Luo, Ming; Wang, Luyao; Xie, Qingguo

2015-03-01

Liver segmentation in CT images has been acknowledged as a basic and indispensable part in systems of computer aided liver surgery for operation design and risk evaluation. In this paper, we will introduce and implement a web-based procedure for liver segmentation to help radiologists and surgeons get an accurate result efficiently and expediently. Several clinical datasets are used to evaluate the accessibility and the accuracy. This procedure seems a promising approach for extraction of liver volumetry of various shapes. Moreover, it is possible for user to access the segmentation wherever the Internet is available without any specific machine.

Concept of Draft International Standard for a Unified Approach to Space Program Quality Assurance

NASA Astrophysics Data System (ADS)

Stryzhak, Y.; Vasilina, V.; Kurbatov, V.

2002-01-01

For want of the unified approach to guaranteed space project and product quality assurance, implementation of many international space programs has become a challenge. Globalization of aerospace industry and participation of various international ventures with diverse quality assurance requirements in big international space programs requires for urgent generation of unified international standards related to this field. To ensure successful fulfillment of space missions, aerospace companies should design and process reliable and safe products with properties complying or bettering User's (or Customer's) requirements. Quality of the products designed or processed by subcontractors (or other suppliers) should also be in compliance with the main user (customer)'s requirements. Implementation of this involved set of unified requirements will be made possible by creating and approving a system (series) of international standards under a generic title Space Product Quality Assurance based on a system consensus principle. Conceptual features of the baseline standard in this system (series) should comprise: - Procedures for ISO 9000, CEN and ECSS requirements adaptation and introduction into space product creation, design, manufacture, testing and operation; - Procedures for quality assurance at initial (design) phases of space programs, with a decision on the end product made based on the principle of independence; - Procedures to arrange incoming inspection of products delivered by subcontractors (including testing, audit of supplier's procedures, review of supplier's documentation), and space product certification; - Procedures to identify materials and primary products applied; - Procedures for quality system audit at the component part, primary product and materials supplier facilities; - Unified procedures to form a list of basic performances to be under configuration management; - Unified procedures to form a list of critical space product components, and unified procedures to define risks related to the specific component application and evaluate safety for the entire program implementation. In the eyes of the authors, those features together with a number of other conceptual proposals should constitute a unified standard-technical basis for implementing international space programs.

48 CFR 34.003 - Responsibilities.

Code of Federal Regulations, 2010 CFR

2010-10-01

... shall identify the key decision points of each major system acquisition and the agency official(s) for making those decisions. (c) Systems acquisitions normally designated as major are those programs that, as... management attention, including specific agency-head decisions. The agency procedures may establish...

Utilizing the public opinion questionnaire to answer policy and process questions.

DOT National Transportation Integrated Search

1978-01-01

The public opinion questionnaire used in this study was designed to provide the Department information regarding public involvement procedures as viewed by the public, as well as to provide insight into citizen opinion regarding the specifics of the ...

The European general thoracic surgery database project.

PubMed

Falcoz, Pierre Emmanuel; Brunelli, Alessandro

2014-05-01

The European Society of Thoracic Surgeons (ESTS) Database is a free registry created by ESTS in 2001. The current online version was launched in 2007. It runs currently on a Dendrite platform with extensive data security and frequent backups. The main features are a specialty-specific, procedure-specific, prospectively maintained, periodically audited and web-based electronic database, designed for quality control and performance monitoring, which allows for the collection of all general thoracic procedures. Data collection is the "backbone" of the ESTS database. It includes many risk factors, processes of care and outcomes, which are specially designed for quality control and performance audit. The user can download and export their own data and use them for internal analyses and quality control audits. The ESTS database represents the gold standard of clinical data collection for European General Thoracic Surgery. Over the past years, the ESTS database has achieved many accomplishments. In particular, the database hit two major milestones: it now includes more than 235 participating centers and 70,000 surgical procedures. The ESTS database is a snapshot of surgical practice that aims at improving patient care. In other words, data capture should become integral to routine patient care, with the final objective of improving quality of care within Europe.

A methodological, task-based approach to Procedure-Specific Simulations training.

PubMed

Setty, Yaki; Salzman, Oren

2016-12-01

Procedure-Specific Simulations (PSS) are 3D realistic simulations that provide a platform to practice complete surgical procedures in a virtual-reality environment. While PSS have the potential to improve surgeons' proficiency, there are no existing standards or guidelines for PSS development in a structured manner. We employ a unique platform inspired by game design to develop virtual reality simulations in three dimensions of urethrovesical anastomosis during radical prostatectomy. 3D visualization is supported by a stereo vision, providing a fully realistic view of the simulation. The software can be executed for any robotic surgery platform. Specifically, we tested the simulation under windows environment on the RobotiX Mentor. Using urethrovesical anastomosis during radical prostatectomy simulation as a representative example, we present a task-based methodological approach to PSS training. The methodology provides tasks in increasing levels of difficulty from a novice level of basic anatomy identification, to an expert level that permits testing new surgical approaches. The modular methodology presented here can be easily extended to support more complex tasks. We foresee this methodology as a tool used to integrate PSS as a complementary training process for surgical procedures.

Thermo-mechanical design aspects of mercury bombardment ion thrusters.

NASA Technical Reports Server (NTRS)

Schnelker, D. E.; Kami, S.

1972-01-01

The mechanical design criteria are presented as background considerations for solving problems associated with the thermomechanical design of mercury ion bombardment thrusters. Various analytical procedures are used to aid in the development of thruster subassemblies and components in the fields of heat transfer, vibration, and stress analysis. Examples of these techniques which provide computer solutions to predict and control stress levels encountered during launch and operation of thruster systems are discussed. Computer models of specific examples are presented.

Tools used to assess medical students competence in procedural skills at the end of a primary medical degree: a systematic review.

PubMed

Morris, Marie C; Gallagher, Tom K; Ridgway, Paul F

2012-01-01

The objective was to systematically review the literature to identify and grade tools used for the end point assessment of procedural skills (e.g., phlebotomy, IV cannulation, suturing) competence in medical students prior to certification. The authors searched eight bibliographic databases electronically - ERIC, Medline, CINAHL, EMBASE, Psychinfo, PsychLIT, EBM Reviews and the Cochrane databases. Two reviewers independently reviewed the literature to identify procedural assessment tools used specifically for assessing medical students within the PRISMA framework, the inclusion/exclusion criteria and search period. Papers on OSATS and DOPS were excluded as they focused on post-registration assessment and clinical rather than simulated competence. Of 659 abstracted articles 56 identified procedural assessment tools. Only 11 specifically assessed medical students. The final 11 studies consisted of 1 randomised controlled trial, 4 comparative and 6 descriptive studies yielding 12 heterogeneous procedural assessment tools for analysis. Seven tools addressed four discrete pre-certification skills, basic suture (3), airway management (2), nasogastric tube insertion (1) and intravenous cannulation (1). One tool used a generic assessment of procedural skills. Two tools focused on postgraduate laparoscopic skills and one on osteopathic students and thus were not included in this review. The levels of evidence are low with regard to reliability - κ = 0.65-0.71 and minimum validity is achieved - face and content. In conclusion, there are no tools designed specifically to assess competence of procedural skills in a final certification examination. There is a need to develop standardised tools with proven reliability and validity for assessment of procedural skills competence at the end of medical training. Medicine graduates must have comparable levels of procedural skills acquisition entering the clinical workforce irrespective of the country of training.

Generic procedure for designing and implementing plan management systems for space science missions operations

NASA Astrophysics Data System (ADS)

Chaizy, P. A.; Dimbylow, T. G.; Allan, P. M.; Hapgood, M. A.

2011-09-01

This paper is one of the components of a larger framework of activities whose purpose is to improve the performance and productivity of space mission systems, i.e. to increase both what can be achieved and the cost effectiveness of this achievement. Some of these activities introduced the concept of Functional Architecture Module (FAM); FAMs are basic blocks used to build the functional architecture of Plan Management Systems (PMS). They also highlighted the need to involve Science Operations Planning Expertise (SOPE) during the Mission Design Phase (MDP) in order to design and implement efficiently operation planning systems. We define SOPE as the expertise held by people who have both theoretical and practical experience in operations planning, in general, and in space science operations planning in particular. Using ESA's methodology for studying and selecting science missions we also define the MDP as the combination of the Mission Assessment and Mission Definition Phases. However, there is no generic procedure on how to use FAMs efficiently and systematically, for each new mission, in order to analyse the cost and feasibility of new missions as well as to optimise the functional design of new PMS; the purpose of such a procedure is to build more rapidly and cheaply such PMS as well as to make the latter more reliable and cheaper to run. This is why the purpose of this paper is to provide an embryo of such a generic procedure and to show that the latter needs to be applied by people with SOPE during the MDP. The procedure described here proposes some initial guidelines to identify both the various possible high level functional scenarii, for a given set of possible requirements, and the information that needs to be associated with each scenario. It also introduces the concept of catalogue of generic functional scenarii of PMS for space science missions. The information associated with each catalogued scenarii will have been identified by the above procedure and will be relevant only for some specific mission requirements. In other words, each mission that shares the same type of requirements that lead to a list of specific catalogued scenarii can use this latter list of scenarii (regardless of whether the mission is a plasma, planetary, astronomy, etc. mission). The main advantages of such a catalogue are that it speeds-up the execution of the procedure and makes the latter more reliable. Ultimately, the information associated to each relevant scenario (from the catalogue or freshly generated by the procedure) will then be used by mission designers to make informed decisions, including the modification of the mission requirements, for any missions. In addition, to illustrate the use of such a procedure, the latter is applied to a case study, i.e. the Cross-Scale mission. One of the outcomes of this study is an initial set of generic functional scenarii. Finally, although border line with the above purpose of this paper, we also discuss multi-spacecraft specific issues and issues related to the on-board execution of the plan update system (PUS). In particular, we show that the operation planning cost of N spacecraft is not equal to N times the cost of 1 spacecraft and that on-board non-synchronised operation will not require inter-spacecraft communication. We also believe that on-board PUS should be made possible for all missions as a standard.

High specific energy, high capacity nickel-hydrogen cell design

NASA Technical Reports Server (NTRS)

Wheeler, James R.

1993-01-01

A 3.5 inch rabbit-ear-terminal nickel-hydrogen cell was designed and tested to deliver high capacity at steady discharge rates up to and including a C rate. Its specific energy yield of 60.6 wh/kg is believed to be the highest yet achieved in a slurry-process nickel-hydrogen cell, and its 10 C capacity of 113.9 AH the highest capacity yet of any type in a 3.5 inch diameter size. The cell also demonstrated a pulse capability of 180 amps for 20 seconds. Specific cell parameters and performance are described. Also covered is an episode of capacity fading due to electrode swelling and its successful recovery by means of additional activation procedures.

[Methodological design of the National Health and Nutrition Survey 2016].

PubMed

Romero-Martínez, Martín; Shamah-Levy, Teresa; Cuevas-Nasu, Lucía; Gómez-Humarán, Ignacio Méndez; Gaona-Pineda, Elsa Berenice; Gómez-Acosta, Luz María; Rivera-Dommarco, Juan Ángel; Hernández-Ávila, Mauricio

2017-01-01

Describe the design methodology of the halfway health and nutrition national survey (Ensanut-MC) 2016. The Ensanut-MC is a national probabilistic survey whose objective population are the inhabitants of private households in Mexico. The sample size was determined to make inferences on the urban and rural areas in four regions. Describes main design elements: target population, topics of study, sampling procedure, measurement procedure and logistics organization. A final sample of 9 479 completed household interviews, and a sample of 16 591 individual interviews. The response rate for households was 77.9%, and the response rate for individuals was 91.9%. The Ensanut-MC probabilistic design allows valid statistical inferences about interest parameters for Mexico´s public health and nutrition, specifically on overweight, obesity and diabetes mellitus. Updated information also supports the monitoring, updating and formulation of new policies and priority programs.

System engineering toolbox for design-oriented engineers

NASA Technical Reports Server (NTRS)

Goldberg, B. E.; Everhart, K.; Stevens, R.; Babbitt, N., III; Clemens, P.; Stout, L.

1994-01-01

This system engineering toolbox is designed to provide tools and methodologies to the design-oriented systems engineer. A tool is defined as a set of procedures to accomplish a specific function. A methodology is defined as a collection of tools, rules, and postulates to accomplish a purpose. For each concept addressed in the toolbox, the following information is provided: (1) description, (2) application, (3) procedures, (4) examples, if practical, (5) advantages, (6) limitations, and (7) bibliography and/or references. The scope of the document includes concept development tools, system safety and reliability tools, design-related analytical tools, graphical data interpretation tools, a brief description of common statistical tools and methodologies, so-called total quality management tools, and trend analysis tools. Both relationship to project phase and primary functional usage of the tools are also delineated. The toolbox also includes a case study for illustrative purposes. Fifty-five tools are delineated in the text.

Investigation of aerodynamic characteristics of subsonic wings

NASA Technical Reports Server (NTRS)

Dejarnette, F. R.; Frink, N. T.

1979-01-01

An analytical strake design procedure is investigated. A numerical solution to the governing strake design equation is used to generate a series of strakes which are tested in a water tunnel to study their vortex breakdown characteristics. The strakes are scaled for use on a half-scale model of the NASA-LaRC general research fuselage with a 44 degrees trapezoidal wing. An analytical solution to the governing design equation is obtained. The strake design procedure relates the potential-flow leading-edge suction and pressure distributions to vortex stability. Several suction distributions are studied and those which are more triangular and peak near the tip generate strakes that reach higher angles of attack before vortex breakdown occurs at the wing trailing edge. For the same suction distribution, a conical rather than three dimensional pressure specification results in a better strake shape as judged from its vortex breakdown characteristics.

Strength of bolted wood joints with various ratios of member thicknesses

Treesearch

Thomas Lee Wilkinson

1978-01-01

Procedures have been recommended–such as in the National Design Specification–for design of bolted joints in wood members where the side members are thicker or thinner than half the main member thickness. However, these recommendations have had no experimental verification up to now. The same is true for joints with other than three members. This study experimentally...

Chapter A10. Lakes and reservoirs: Guidelines for study design and sampling

USGS Publications Warehouse

Green, William R.; Robertson, Dale M.; Wilde, Franceska D.

2015-09-29

Within this chapter are references to other chapters of the NFM that provide more detailed guidelines related to specific topics and more detailed protocols for the quality assurance and assessment of the lake and reservoir data. Protocols and procedures to address and document the quality of lake and reservoir investigations are adapted from, or referenced to, the protocols and standard operating procedures contained in related chapters of this National Field Manual.

Pediatric Drowning: A Standard Operating Procedure to Aid the Prehospital Management of Pediatric Cardiac Arrest Resulting From Submersion.

PubMed

Best, Rebecca R; Harris, Benjamin H L; Walsh, Jason L; Manfield, Timothy

2017-05-08

Drowning is one of the leading causes of death in children. Resuscitating a child following submersion is a high-pressure situation, and standard operating procedures can reduce error. Currently, the Resuscitation Council UK guidance does not include a standard operating procedure on pediatric drowning. The objective of this project was to design a standard operating procedure to improve outcomes of drowned children. A literature review on the management of pediatric drowning was conducted. Relevant publications were used to develop a standard operating procedure for management of pediatric drowning. A concise standard operating procedure was developed for resuscitation following pediatric submersion. Specific recommendations include the following: the Heimlich maneuver should not be used in this context; however, prolonged resuscitation and therapeutic hypothermia are recommended. This standard operating procedure is a potentially useful adjunct to the Resuscitation Council UK guidance and should be considered for incorporation into its next iteration.

Computer method for design of acoustic liners for turbofan engines

NASA Technical Reports Server (NTRS)

Minner, G. L.; Rice, E. J.

1976-01-01

A design package is presented for the specification of acoustic liners for turbofans. An estimate of the noise generation was made based on modifications of existing noise correlations, for which the inputs are basic fan aerodynamic design variables. The method does not predict multiple pure tones. A target attenuation spectrum was calculated which was the difference between the estimated generation spectrum and a flat annoyance-weighted goal attenuated spectrum. The target spectrum was combined with a knowledge of acoustic liner performance as a function of the liner design variables to specify the acoustic design. The liner design method at present is limited to annular duct configurations. The detailed structure of the liner was specified by combining the required impedance (which is a result of the previous step) with a mathematical model relating impedance to the detailed structure. The design procedure was developed for a liner constructed of perforated sheet placed over honeycomb backing cavities. A sample calculation was carried through in order to demonstrate the design procedure, and experimental results presented show good agreement with the calculated results of the method.

Handbook for Teachers of the Visually Handicapped.

ERIC Educational Resources Information Center

Napier, Grace D.; Weishahn, Mel W.

Designed to aid the inexperienced teacher of the visually handicapped, the handbook examines aspects of program objectives, content, philosophy, methods, eligibility, and placement procedures. The guide to material selection provides specific information on the acquisition of Braille materials, large type materials, recorded materials, direct…

Improvement for determining the axial capacity of drilled shafts in shale in Illinois.

DOT National Transportation Integrated Search

2013-05-01

In this project, Illinois-specific design procedures were developed for drilled shafts founded in weak shale. In addition, : recommendations for field and laboratory testing to characterize the in situ condition of weak shales in Illinois were : deve...

49 CFR 180.413 - Repair, modification, stretching, rebarrelling, or mounting of specification cargo tanks.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS CONTINUING QUALIFICATION AND MAINTENANCE OF PACKAGINGS Qualification and Maintenance... respect to structural design analysis, material and welding procedures. (ii) Assure compliance of the...

Warehousing Operations.

ERIC Educational Resources Information Center

Marine Corps Inst., Washington, DC.

Developed as part of the Marine Corps Institute (MCI) correspondence training program, this course on warehousing operations is designed to provide instruction in the procedures used in warehousing operations. Introductory materials include specific information for MCI students and a study guide (guidelines to complete the course). The 22-hour…

Forensic Pathology: A Handbook for Pathologists.

ERIC Educational Resources Information Center

Fisher, Russell S., Ed.; Petty, Charles S., Ed.

This document provides a guide containing basic information for community pathologists to perform medical legal autopsies. Thirty-two chapters consider procedures to use in general and specific situations. Each chapter was written by a specialist. The publication is designed to supplement existing publications. (SL)

40 CFR 40.115-1 - Construction.

Code of Federal Regulations, 2011 CFR

2011-07-01

... investigations and studies, surveys, designs, plans, working drawings, specifications, procedures, and other... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Construction. 40.115-1 Section 40.115-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE RESEARCH AND...

40 CFR 40.115-1 - Construction.

Code of Federal Regulations, 2010 CFR

2010-07-01

... investigations and studies, surveys, designs, plans, working drawings, specifications, procedures, and other... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Construction. 40.115-1 Section 40.115-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE RESEARCH AND...

40 CFR 40.115-1 - Construction.

Code of Federal Regulations, 2013 CFR

2013-07-01

... investigations and studies, surveys, designs, plans, working drawings, specifications, procedures, and other... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Construction. 40.115-1 Section 40.115-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE RESEARCH AND...

40 CFR 40.115-1 - Construction.

Code of Federal Regulations, 2014 CFR

2014-07-01

... investigations and studies, surveys, designs, plans, working drawings, specifications, procedures, and other... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Construction. 40.115-1 Section 40.115-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE RESEARCH AND...

40 CFR 40.115-1 - Construction.

Code of Federal Regulations, 2012 CFR

2012-07-01

... investigations and studies, surveys, designs, plans, working drawings, specifications, procedures, and other... 40 Protection of Environment 1 2012-07-01 2012-07-01 false Construction. 40.115-1 Section 40.115-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE RESEARCH AND...

Site-specific seismic ground motion analyses for transportation infrastructure in the New Madrid seismic zone.

DOT National Transportation Integrated Search

2012-11-01

Generic, code-based design procedures cannot account for the anticipated short-period attenuation and long-period amplification of earthquake ground motions in the deep, soft sediments of the Mississippi Embayment within the New Madrid Seismic Zone (...

You Sank My... Bacteriophage?

ERIC Educational Resources Information Center

Bokor, Julie

2012-01-01

Practicing correct pipetting procedure doesn't have to be boring. "Pipetting by Coordinates" is an effective way to teach necessary pipetting skills in an enjoyable manner. Students create designs as they add volumes of colored water to specific wells and gain experience using a basic biotechnology tool.

Improved digital transfer of the maxillary cast to a virtual articulator.

PubMed

Solaberrieta, Eneko; Otegi, Jose Ramon; Mínguez, Rikardo; Etxaniz, Olatz

2014-10-01

The clinical procedure described provides a quantifiable, repeatable, and reliable method of transferring the location of the maxillary dental arch from the patient directly to a virtual articulator (virtual facebow transfer) by means of reverse engineering devices to design a customized dental restoration. This procedure allows the dentist and the dental laboratory technician to work in a fully digital environment without having to mount stone casts on a mechanical articulator. In addition, specific suggestions are provided for designing the transfer device to enhance patient comfort during the data transfer process and reduce deviation. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Does neonatal pain management in intensive care units differ between night and day? An observational study

PubMed Central

Guedj, Romain; Danan, Claude; Daoud, Patrick; Zupan, Véronique; Renolleau, Sylvain; Zana, Elodie; Aizenfisz, Sophie; Lapillonne, Alexandre; de Saint Blanquat, Laure; Granier, Michèle; Durand, Philippe; Castela, Florence; Coursol, Anne; Hubert, Philippe; Cimerman, Patricia; Anand, K J S; Khoshnood, Babak; Carbajal, Ricardo

2014-01-01

Objective To determine whether analgesic use for painful procedures performed in neonates in the neonatal intensive care unit (NICU) differs during nights and days and during each of the 6 h period of the day. Design Conducted as part of the prospective observational Epidemiology of Painful Procedures in Neonates study which was designed to collect in real time and around-the-clock bedside data on all painful or stressful procedures. Setting 13 NICUs and paediatric intensive care units in the Paris Region, France. Participants All 430 neonates admitted to the participating units during a 6-week period between September 2005 and January 2006. Data collection During the first 14 days of admission, data were collected on all painful procedures and analgesic therapy. The five most frequent procedures representing 38 012 of all 42 413 (90%) painful procedures were analysed. Intervention Observational study. Main outcome assessment We compared the use of specific analgesic for procedures performed during each of the 6 h period of a day: morning (7:00 to 12:59), afternoon, early night and late night and during daytime (morning+afternoon) and night-time (early night+late night). Results 7724 of 38 012 (20.3%) painful procedures were carried out with a specific analgesic treatment. For morning, afternoon, early night and late night, respectively, the use of analgesic was 25.8%, 18.9%, 18.3% and 18%. The relative reduction of analgesia was 18.3%, p<0.01, between daytime and night-time and 28.8%, p<0.001, between morning and the rest of the day. Parental presence, nurses on 8 h shifts and written protocols for analgesia were associated with a decrease in this difference. Conclusions The substantial differences in the use of analgesics around-the-clock may be questioned on quality of care grounds. PMID:24556241

Drilling and completion specifications for CA series multilevel piezometers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clawson, T.S.

1986-08-01

CX Series multilevel piezometer boreholes will provide information on hydraulic heads in the Rosalia, Sentinel Gap, Ginkgo, Rocky Coulee, Cohassett, Birkett, and Umtanum flow tops. The borehole sites will be located adjacent to the reference repository location. In addition, information from the boreholes will provide input data used to determine horizontal and vertical flow rates, and identify possible geologic structures. This specification includes details for drilling, piezometer design, hydrologic testing, and hydrochemical sampling of the boreholes. It includes drilling requirements, design, and installation procedures for the series piezometer nests, intervals selected for head monitoring and schedules for drilling and piezometermore » installation. Specific drilling and piezometer installation specifications for boreholes DC-24CX and DC-25CX are also included. 27 refs., 5 figs., 3 tabs.« less

Laboratory and clinical genomic data sharing is crucial to improving genetic health care: a position statement of the American College of Medical Genetics and Genomics.

PubMed

Acmg Board Of Directors

2017-07-01

Disclaimer: These recommendations are designed primarily as an educational resource for medical geneticists and other health-care providers, to help them provide quality medical genetic services. Adherence to these recommendations does not necessarily assure a successful medical outcome. These recommendations should not be considered inclusive of all proper procedures and tests or exclusive of other procedures and tests that are reasonably directed to obtaining the same results. In determining the propriety of any specific procedure or test, the geneticist should apply his or her own professional judgment to the specific clinical circumstances presented by the individual patient or specimen. It may be prudent, however, to document in the patient's record the rationale for any significant deviation from these recommendations.Genet Med advance online publication 05 January 2017.

Quantification of Processing Effects on Filament Wound Pressure Vessels

NASA Technical Reports Server (NTRS)

Aiello, Robert A.; Chamis, Christos C.

1999-01-01

A computational simulation procedure is described which is designed specifically for the modeling and analysis of filament wound pressure vessels. Cylindrical vessels with spherical or elliptical end caps can be generated automatically. End caps other than spherical or elliptical may be modeled by varying circular sections along the x-axis according to the C C! end cap shape. The finite element model generated is composed of plate type quadrilateral shell elements on the entire vessel surface. This computational procedure can also be sued to generate grid, connectivity and material cards (bulk data) for component parts of a larger model. These bulk data are assigned to a user designated file for finite element structural/stress analysis of composite pressure vessels. The procedure accommodates filament would pressure vessels of all types of shells-of-revolution. It has provisions to readily evaluate initial stresses due to pretension in the winding filaments and residual stresses due to cure temperature.

Quantification of Processing Effects on Filament Wound Pressure Vessels. Revision

NASA Technical Reports Server (NTRS)

Aiello, Robert A.; Chamis, Christos C.

2002-01-01

A computational simulation procedure is described which is designed specifically for the modeling and analysis of filament wound pressure vessels. Cylindrical vessels with spherical or elliptical end caps can be generated automatically. End caps other than spherical or elliptical may be modeled by varying circular sections along the x-axis according to the end cap shape. The finite element model generated is composed of plate type quadrilateral shell elements on the entire vessel surface. This computational procedure can also be used to generate grid, connectivity and material cards (bulk data) for component parts of a larger model. These bulk data are assigned to a user designated file for finite element structural/stress analysis of composite pressure vessels. The procedure accommodates filament wound pressure vessels of all types of shells-of -revolution. It has provisions to readily evaluate initial stresses due to pretension in the winding filaments and residual stresses due to cure temperature.

Interventional Spine and Pain Procedures in Patients on Antiplatelet and Anticoagulant Medications (Second Edition): Guidelines From the American Society of Regional Anesthesia and Pain Medicine, the European Society of Regional Anaesthesia and Pain Therapy, the American Academy of Pain Medicine, the International Neuromodulation Society, the North American Neuromodulation Society, and the World Institute of Pain.

PubMed

Narouze, Samer; Benzon, Honorio T; Provenzano, David; Buvanendran, Asokumar; De Andres, José; Deer, Timothy; Rauck, Richard; Huntoon, Marc A

2018-04-01

The American Society of Regional Anesthesia and Pain Medicine (ASRA) 2012 survey of meeting attendees showed that existing ASRA anticoagulation guidelines for regional anesthesia were insufficient for their needs. Those surveyed agreed that procedure-specific and patient-specific factors required separate guidelines for pain and spine procedures. In response, a guidelines committee was formed. After preliminary review of published complications reports and studies, the committee stratified interventional spine and pain procedures according to potential bleeding risk: low-, intermediate-, and high-risk procedures. The ASRA regional anesthesia anticoagulation guidelines were largely deemed appropriate for the low- and intermediate-risk categories, but the high-risk category required further investigation. The first guidelines specific to interventional spine and pain procedures were published in 2015. Recent reviews evaluating bleeding complications in patients undergoing specific interventional pain procedures, the development of new regional anesthesia and acute pain guidelines, and the development of new anticoagulants and antiplatelet medications necessitate complementary updated guidelines. The authors desired coordination with the authors of the recently updated regional and acute pain anticoagulation guidelines. The latest evidence was sought through extensive database search strategies and the recommendations were evidence based when available and pharmacology driven otherwise. We could not provide strength and grading of these recommendations because there are not enough well-designed large studies concerning interventional pain procedures to support such grading. Although the guidelines could not always be based on randomized studies or on large numbers of patients from pooled databases, it is hoped that they will provide sound recommendations and the evidentiary basis for such recommendations. This publication is intended as a living document to be updated periodically with consideration of new evidence.

A microprogrammed data acquisition system for renography.

PubMed

Imperiale, C

1983-01-01

The purpose of this project was to design an efficient, low cost, and portable system for renography suitable for clinical use. The principles involved in the renographic test, and the procedures and calculations which act on the design of our system, are given. The system consists of an Apple II Plus computer equipped with 48K memory, two disk drives with diskettes of 143K each, a thermal printer with graphic capability, the Microsoft Z80 card, and an interface which is specifically designed for renographic data acquisition.

OCP TECD Report - TARDEC Blast Mitigation Program (BMP) and National Defense Industrial Association (NDIA) Michigan (MI) Chapter Cooperative Research and Development Agreement (CRADA) Summary

DTIC Science & Technology

2017-09-26

on the desire of both parties to collaborate to develop a practical and useable set of Blast Mitigation Program (BMP) design guidelines and...standards. The effort focused on the following topics: occupant-centric design philosophy and terms, test procedures, Military performance specifications...NDIA) was created based on the desire of both parties to collaborate to develop a practical and useable set of Blast Mitigation Program (BMP) design

Flutter optimization in fighter aircraft design

NASA Technical Reports Server (NTRS)

Triplett, W. E.

1984-01-01

The efficient design of aircraft structure involves a series of compromises among various engineering disciplines. These compromises are necessary to ensure the best overall design. To effectively reconcile the various technical constraints requires a number of design iterations, with the accompanying long elapsed time. Automated procedures can reduce the elapsed time, improve productivity and hold the promise of optimum designs which may be missed by batch processing. Several examples are given of optimization applications including aeroelastic constraints. Particular attention is given to the success or failure of each example and the lessons learned. The specific applications are shown. The final two applications were made recently.

Estimation of sample size and testing power (part 5).

PubMed

Hu, Liang-ping; Bao, Xiao-lei; Guan, Xue; Zhou, Shi-guo

2012-02-01

Estimation of sample size and testing power is an important component of research design. This article introduced methods for sample size and testing power estimation of difference test for quantitative and qualitative data with the single-group design, the paired design or the crossover design. To be specific, this article introduced formulas for sample size and testing power estimation of difference test for quantitative and qualitative data with the above three designs, the realization based on the formulas and the POWER procedure of SAS software and elaborated it with examples, which will benefit researchers for implementing the repetition principle.

Application of a repetitive process setting to design of monotonically convergent iterative learning control

NASA Astrophysics Data System (ADS)

Boski, Marcin; Paszke, Wojciech

2015-11-01

This paper deals with the problem of designing an iterative learning control algorithm for discrete linear systems using repetitive process stability theory. The resulting design produces a stabilizing output feedback controller in the time domain and a feedforward controller that guarantees monotonic convergence in the trial-to-trial domain. The results are also extended to limited frequency range design specification. New design procedure is introduced in terms of linear matrix inequality (LMI) representations, which guarantee the prescribed performances of ILC scheme. A simulation example is given to illustrate the theoretical developments.

Competency-Based Education in Low Resource Settings: Development of a Novel Surgical Training Program.

PubMed

McCullough, Meghan; Campbell, Alex; Siu, Armando; Durnwald, Libby; Kumar, Shubha; Magee, William P; Swanson, Jordan

2018-03-01

The unmet burden of surgical disease represents a major global health concern, and a lack of trained providers is a critical component of the inadequacy of surgical care worldwide. Competency-based training has been advanced in high-income countries, improving technical skills and decreasing training time, but it is poorly understood how this model might be applied to low- and middle-income countries. We describe the development of a competency-based program to accelerate specialty training of in-country providers in cleft surgery techniques. The program was designed and piloted among eight trainees at five international cleft lip and palate surgical mission sites in Latin America and Africa. A competency-based evaluation form, designed for the program, was utilized to grade general technical and procedure-specific competencies, and pre- and post-training scores were analyzed using a paired t test. Trainees demonstrated improvement in average procedure-specific competency scores for both lip repairs (60.4-71.0%, p < 0.01) and palate (50.6-66.0%, p < 0.01). General technical competency scores also improved (63.6-72.0%, p < 0.01). Among the procedural competencies assessed, surgical markings showed the greatest improvement (19.0 and 22.8% for lip and palate, respectively), followed by nasal floor/mucosal approximation (15.0%) and hard palate dissection (17.1%). Surgical delivery models in LMICs are varied, and trade-offs often exist between goals of case throughput, quality and training. Pilot program results show that procedure-specific and general technical competencies can be improved over a relatively short time and demonstrate the feasibility of incorporating such a training program into surgical outreach missions.

Towards sensible toxicity testing for nanomaterials: proposal for the specification of test design.

PubMed

Potthoff, Annegret; Weil, Mirco; Meißner, Tobias; Kühnel, Dana

2015-12-01

During the last decade, nanomaterials (NM) were extensively tested for potential harmful effects towards humans and environmental organisms. However, a sound hazard assessment was so far hampered by uncertainties and a low comparability of test results. The reason for the low comparability is a high variation in the (1) type of NM tested with regard to raw material, size and shape and (2) procedures before and during the toxicity testing. This calls for tailored, nanomaterial-specific protocols. Here, a structured approach is proposed, intended to lead to test protocols not only tailored to specific types of nanomaterials, but also to respective test system for toxicity testing. There are existing standards on single procedures involving nanomaterials, however, not all relevant procedures are covered by standards. Hence, our approach offers a detailed way of weighting several plausible alternatives for e.g. sample preparation, in order to decide on the procedure most meaningful for a specific nanomaterial and toxicity test. A framework of several decision trees (DT) and flow charts to support testing of NM is proposed as a basis for further refinement and in-depth elaboration. DT and flow charts were drafted for (1) general procedure-physicochemical characterisation, (2) choice of test media, (3) decision on test scenario and application of NM to liquid media, (4) application of NM to the gas phase, (5) application of NM to soil and sediments, (6) dose metrics, (S1) definition of a nanomaterial, and (S2) dissolution. The applicability of the proposed approach was surveyed by using experimental data retrieved from studies on nanoscale CuO. This survey demonstrated the DT and flow charts to be a convenient tool to systematically decide upon test procedures and processes, and hence pose an important step towards harmonisation of NM testing.

40 CFR 91.404 - Test procedure overview.

Code of Federal Regulations, 2010 CFR

2010-07-01

... analyzed through the analytical system. (b) The tests are designed to determine the brake-specific... four power modes with an exponential relationship between torque and speed which span the typical... the concentration of each pollutant, fuel flow, and the power output during each mode. The measured...

19 CFR Appendix A to Part 191 - General Manufacturing Drawback Rulings

Code of Federal Regulations, 2010 CFR

2010-04-01

... manufacture or production. B. These general manufacturing drawback rulings supersede general “contracts... manufacturing drawback rulings which have been designed to simplify drawback procedures. Any person who can... drawback; and 9. Description of the manufacturing or production process, unless specifically described in...

Estimating Classification Consistency and Accuracy for Cognitive Diagnostic Assessment

ERIC Educational Resources Information Center

Cui, Ying; Gierl, Mark J.; Chang, Hua-Hua

2012-01-01

This article introduces procedures for the computation and asymptotic statistical inference for classification consistency and accuracy indices specifically designed for cognitive diagnostic assessments. The new classification indices can be used as important indicators of the reliability and validity of classification results produced by…

46 CFR 56.50-85 - Tank-vent piping.

Code of Federal Regulations, 2011 CFR

2011-10-01

...-control systems or other, equivalent means, together with gauging devices and procedures for filling cargo... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Design Requirements Pertaining to Specific Systems § 56.50-85 Tank-vent piping. (a) This section...

SHARING EDUCATIONAL SERVICES.

ERIC Educational Resources Information Center

Catskill Area Project in Small School Design, Oneonta, NY.

SHARED SERVICES, A COOPERATIVE SCHOOL RESOURCE PROGRAM, IS DEFINED IN DETAIL. INCLUDED IS A DISCUSSION OF THEIR NEED, ADVANTAGES, GROWTH, DESIGN, AND OPERATION. SPECIFIC PROCEDURES FOR OBTAINING STATE AID IN SHARED SERVICES, EFFECTS OF SHARED SERVICES ON THE SCHOOL, AND HINTS CONCERNING SHARED SERVICES ARE DESCRIBED. CHARACTERISTICS OF THE SMALL…

76 FR 39132 - Agency Information Collection Activities: Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-05

... objects or materials for a variety of purposes in research, industry, and other fields. The subparts cover specific requirements for obtaining a license or license exemption, design and performance criteria for... training, written operating and emergency procedures, personnel monitoring, radiation surveys, inspection...

MCPS Curriculum Development Planning Process.

ERIC Educational Resources Information Center

Montgomery County Public Schools, Rockville, MD. Dept. of Instructional Planning and Development.

The procedure documented is used for the systemwide planning of curriculum development in Montgomery County, Maryland, and consists of three parts: a planning and review process; an instructional design and development model; and a proposed calendar for cyclical review of programs. Specific position responsibilities, organizational charts, and…

40 CFR 90.404 - Test procedure overview.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) CONTROL OF EMISSIONS FROM NONROAD SPARK-IGNITION ENGINES AT OR BELOW 19 KILOWATTS Gaseous Exhaust... engine operating conditions to be conducted on an engine dynamometer or equivalent load and speed... also designed to determine the brake-specific emissions of non-methane hydrocarbons. The test consists...

40 CFR 90.404 - Test procedure overview.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) CONTROL OF EMISSIONS FROM NONROAD SPARK-IGNITION ENGINES AT OR BELOW 19 KILOWATTS Gaseous Exhaust... engine operating conditions to be conducted on an engine dynamometer or equivalent load and speed... also designed to determine the brake-specific emissions of non-methane hydrocarbons. The test consists...

40 CFR 90.404 - Test procedure overview.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) CONTROL OF EMISSIONS FROM NONROAD SPARK-IGNITION ENGINES AT OR BELOW 19 KILOWATTS Gaseous Exhaust... engine operating conditions to be conducted on an engine dynamometer or equivalent load and speed... also designed to determine the brake-specific emissions of non-methane hydrocarbons. The test consists...

40 CFR 90.404 - Test procedure overview.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) CONTROL OF EMISSIONS FROM NONROAD SPARK-IGNITION ENGINES AT OR BELOW 19 KILOWATTS Gaseous Exhaust... engine operating conditions to be conducted on an engine dynamometer or equivalent load and speed... also designed to determine the brake-specific emissions of non-methane hydrocarbons. The test consists...

A methodology for hypersonic transport technology planning

NASA Technical Reports Server (NTRS)

Repic, E. M.; Olson, G. A.; Milliken, R. J.

1973-01-01

A systematic procedure by which the relative economic value of technology factors affecting design, configuration, and operation of a hypersonic cruise transport can be evaluated is discussed. Use of the methodology results in identification of first-order economic gains potentially achievable by projected advances in each of the definable, hypersonic technologies. Starting with a baseline vehicle, the formulas, procedures and forms which are integral parts of this methodology are developed. A demonstration of the methodology is presented for one specific hypersonic vehicle system.

Design and development of polyphenylene oxide foam as a reusable internal insulation for LH2 tanks

NASA Technical Reports Server (NTRS)

1975-01-01

Material specification and fabrication process procedures for foam production are presented. The properties of mechanical strength, modulus of elasticity, density and thermal conductivity were measured and related to foam quality. Properties unique to the foam such as a gas layer insulation, density gradient parallel to the fiber direction, and gas flow conductance in both directions were correlated with foam quality. Inspection and quality control tests procedures are outlined and photographs of test equipment and test specimens are shown.

Blood Sampling and Preparation Procedures for Proteomic Biomarker Studies of Psychiatric Disorders.

PubMed

Guest, Paul C; Rahmoune, Hassan

2017-01-01

A major challenge in proteomic biomarker discovery and validation for psychiatric diseases is the inherent biological complexity underlying these conditions. There are also many technical issues which hinder this process such as the lack of standardization in sampling, processing and storage of bio-samples in preclinical and clinical settings. This chapter describes a reproducible procedure for sampling blood serum and plasma that is specifically designed for maximizing data quality output in two-dimensional gel electrophoresis, multiplex immunoassay and mass spectrometry profiling studies.

Fabrication of fuel pin assemblies, phase 3

NASA Technical Reports Server (NTRS)

Keeton, A. R.; Stemann, L. G.

1972-01-01

Five full size and eight reduced length fuel pins were fabricated for irradiation testing to evaluate design concepts for a fast spectrum lithium cooled compact space power reactor. These assemblies consisted of uranium mononitride fuel pellets encased in a T-111 (Ta-8W-2Hf) clad with a tungsten barrier separating fuel and clad. Fabrication procedures were fully qualified by process development and assembly qualification tests. Detailed specifications and procedures were written for the fabrication and assembly of prototype fuel pins.

A methodology for boost-glide transport technology planning

NASA Technical Reports Server (NTRS)

Repic, E. M.; Olson, G. A.; Milliken, R. J.

1974-01-01

A systematic procedure is presented by which the relative economic value of technology factors affecting design, configuration, and operation of boost-glide transport can be evaluated. Use of the methodology results in identification of first-order economic gains potentially achievable by projected advances in each of the definable, hypersonic technologies. Starting with a baseline vehicle, the formulas, procedures and forms which are integral parts of this methodology are developed. A demonstration of the methodology is presented for one specific boost-glide system.

Bilateral Malar Reconstruction Using Patient-Specific Polyether Ether Ketone Implants in Treacher-Collins Syndrome Patients With Absent Zygomas.

PubMed

Sainsbury, David C G; George, Alan; Forrest, Christopher R; Phillips, John H

2017-03-01

The authors performed bilateral malar reconstruction using polyether ether ketone implants in 3 patients with Treacher-Collins syndrome with absent, as opposed to hypoplastic, zygomata. These patient-specific implants were fabricated using computed-aided design software reformatted from three-dimensional bony preoperative computed tomography images. The first time the authors performed this procedure the implant compressed the globe resulting in temporary anisocoria that was quickly recognized intraoperatively. The implant was immediately removed and the patient made a full-recovery with no ocular disturbance. The computer-aided design and manufacturing process was adjusted to include periorbital soft-tissue boundaries to aid in contouring the new implants. The same patient, and 2 further patients, subsequently underwent malar reconstruction using this soft tissue periorbital boundary fabrication process with an additional 2 mm relief removed from the implant's orbital surface. These subsequent procedures were performed without complication and with pleasing aesthetic results. The authors describe their experience and the salutary lessons learnt.

Revision to Planetary Protection Policy for Mars Missions

NASA Technical Reports Server (NTRS)

DeVincenzi, D. L.; Stabekis, P.; Barengoltz, J.; Morrison, David (Technical Monitor)

1994-01-01

Under existing COSPAR policy adopted in 1984, missions to Mars (landers, probes, and some orbiters) are designated as Category IV missions. As such, the procedures for implementing planetary protection requirements could include trajectory biasing, cleanrooms, bioload reduction, sterilization of hardware, and bioshields, i. e. requirements could be similar to Viking. However, in 1992, a U. S. National Academy of Sciences study recommended that controls on forward contamination of Mars be tied to specific mission objectives. The report recommended that Mars landers with life detection instruments be subject to at least Viking-level sterilization procedures for bioload reduction, while spacecraft (including orbiters) without life detection instruments be subject to at least Viking-level pre sterilization procedures for bioload reduction but need not be sterilized. In light of this, it is proposed that the current policy's Category IV missions and their planetary protection requirements be divided into two subcategories as follows: Category IV A, for missions comprising landers and probes without life detection experiments and some orbiters, which will meet a specified bioburden limit for exposed surfaces; Category IV B, for landers and probes with life detection experiments, which will require complete system sterilization. For Category IV A missions, bioburden specifications will be proposed and implementing procedures discussed. A resolution will be proposed to modify the existing COSPAR policy to reflect these changes. Similar specifications, procedures, and resolution for Category IV B missions will be the subject of a later study.

Radiation Hardness Assurance (RHA) for Space Systems

NASA Technical Reports Server (NTRS)

Poivey, Christian; Buchner, Stephen

2007-01-01

This presentation discusses radiation hardness assurance (RHA) for space systems, providing both the programmatic aspects of RHA and the RHA procedure. RHA consists of all activities undertaken to ensure that the electronics and materials of a space system perform to their design specifications after exposure to the space radiation environment. RHA also pertains to environment definition, part selection, part testing, spacecraft layout, radiation tolerant design, and mission/system/subsystems requirements. RHA procedure consists of establishing mission requirements, defining and evaluating the radiation hazard, selecting and categorizing the appropriate parts, and evaluating circuit response to hazard. The RHA approach is based on risk management and is confined only to parts, it includes spacecraft layout, system/subsystem/circuit design, and system requirements and system operations. RHA should be taken into account in the early phases of a program including the proposal and feasibility analysis phases.

Display formats manual

NASA Technical Reports Server (NTRS)

Runnels, R. L.

1973-01-01

The standards and procedures for the generation of operational display formats to be used in the Mission Control Center (MCC) display control system are presented. The required effort, forms, and fundamentals for the design, specifications, and production of display formats are identified. The principles of display design and system constraints controlling the creation of optimum operational displays for mission control are explained. The basic two types of MCC display systems for presenting information are described.

A conceptual framework for the design of environmental post-market monitoring of genetically modified plants.

PubMed

Sanvido, Olivier; Widmer, Franco; Winzeler, Michael; Bigler, Franz

2005-01-01

Genetically modified plants (GMPs) may soon be cultivated commercially in several member countries of the European Union (EU). According to EU Directive 2001/18/EC, post-market monitoring (PMM) for commercial GMP cultivation must be implemented, in order to detect and prevent adverse effects on human health and the environment. However, no general PMM strategies for GMP cultivation have been established so far. We present a conceptual framework for the design of environmental PMM for GMP cultivation based on current EU legislation and common risk analysis procedures. We have established a comprehensive structure of the GMP approval process, consisting of pre-market risk assessment (PMRA) as well as PMM. Both programs can be distinguished conceptually due to principles inherent to risk analysis procedures. The design of PMM programs should take into account the knowledge gained during approval for commercialization of a specific GMP and the decisions made in the environmental risk assessments (ERAs). PMM is composed of case-specific monitoring (CSM) and general surveillance. CSM focuses on anticipated effects of a specific GMP. Selection of case-specific indicators for detection of ecological exposure and effects, as well as definition of effect sizes, are important for CSM. General surveillance is designed to detect unanticipated effects on general safeguard subjects, such as natural resources, which must not be adversely affected by human activities like GMP cultivation. We have identified clear conceptual differences between CSM and general surveillance, and propose to adopt separate frameworks when developing either of the two programs. Common to both programs is the need to put a value on possible ecological effects of GMP cultivation. The structure of PMM presented here will be of assistance to industry, researchers, and regulators, when assessing GMPs during commercialization.

A Unique Procedure to Identify Cell Surface Markers Through a Spherical Self-Organizing Map Applied to DNA Microarray Analysis.

PubMed

Sugii, Yuh; Kasai, Tomonari; Ikeda, Masashi; Vaidyanath, Arun; Kumon, Kazuki; Mizutani, Akifumi; Seno, Akimasa; Tokutaka, Heizo; Kudoh, Takayuki; Seno, Masaharu

2016-01-01

To identify cell-specific markers, we designed a DNA microarray platform with oligonucleotide probes for human membrane-anchored proteins. Human glioma cell lines were analyzed using microarray and compared with normal and fetal brain tissues. For the microarray analysis, we employed a spherical self-organizing map, which is a clustering method suitable for the conversion of multidimensional data into two-dimensional data and displays the relationship on a spherical surface. Based on the gene expression profile, the cell surface characteristics were successfully mirrored onto the spherical surface, thereby distinguishing normal brain tissue from the disease model based on the strength of gene expression. The clustered glioma-specific genes were further analyzed by polymerase chain reaction procedure and immunocytochemical staining of glioma cells. Our platform and the following procedure were successfully demonstrated to categorize the genes coding for cell surface proteins that are specific to glioma cells. Our assessment demonstrates that a spherical self-organizing map is a valuable tool for distinguishing cell surface markers and can be employed in marker discovery studies for the treatment of cancer.

An information system design for watershed-wide modeling of water loss to the atmosphere using remote sensing techniques

NASA Technical Reports Server (NTRS)

Khorram, S.

1977-01-01

Results are presented of a study intended to develop a general location-specific remote-sensing procedure for watershed-wide estimation of water loss to the atmosphere by evaporation and transpiration. The general approach involves a stepwise sequence of required information definition (input data), appropriate sample design, mathematical modeling, and evaluation of results. More specifically, the remote sensing-aided system developed to evaluate evapotranspiration employs a basic two-stage two-phase sample of three information resolution levels. Based on the discussed design, documentation, and feasibility analysis to yield timely, relatively accurate, and cost-effective evapotranspiration estimates on a watershed or subwatershed basis, work is now proceeding to implement this remote sensing-aided system.

Orbital Reconstruction: Patient-Specific Orbital Floor Reconstruction Using a Mirroring Technique and a Customized Titanium Mesh.

PubMed

Tarsitano, Achille; Badiali, Giovanni; Pizzigallo, Angelo; Marchetti, Claudio

2016-10-01

Enophthalmos is a severe complication of primary reconstruction of orbital floor fractures. The goal of secondary reconstruction procedures is to restore symmetrical globe positions to recover function and aesthetics. The authors propose a new method of orbital floor reconstruction using a mirroring technique and a customized titanium mesh, printed using a direct metal laser-sintering method. This reconstructive protocol involves 4 steps: mirroring of the healthy orbit at the affected site, virtual design of a patient-specific orbital floor mesh, CAM procedures for direct laser-sintering of the customized titanium mesh, and surgical insertion of the device. Using a computed tomography data set, the normal, uninjured side of the craniofacial skeleton was reflected onto the contralateral injured side, and a reconstructive orbital floor mesh was designed virtually on the mirrored orbital bone surface. The solid-to-layer files of the mesh were then manufactured using direct metal laser sintering, which resolves the shaping and bending biases inherent in the indirect method. An intraoperative navigation system ensured accuracy of the entire procedure. Clinical outcomes were assessed using 3dMD photogrammetry and computed tomography data in 7 treated patients. The technique described here appears to be a viable method to correct complex orbital floor defects needing delayed reconstruction. This study represents the first step in the development of a wider experimental protocol for orbital floor reconstruction using computer-assisted design-computer-assisted manufacturing technology.

Review of musculoskeletal injuries and prevention in the endoscopy practitioner.

PubMed

Harvin, Glenn

2014-08-01

Practitioners of endoscopy often experience musculoskeletal pain and injury (most often in the back, neck, shoulders, hands, wrists, and thumbs) that are associated with the minute and repetitive strain that is placed on these areas during endoscopic procedures. This review of the current documentation of endoscopy-related pain and injuries among practitioners finds that such problems are widespread and specific in kind as well as strongly correlated with high procedure volume and procedure duration. Research on the nature and impact of cumulative trauma and overuse syndromes in other professions such as dentistry, pianists, production labor, and athletics is brought to bear on the work of the endoscopist. A more thorough understanding of the nature and prevalence of work-related pain and injury sustained by endoscopists should inform further development of ergonomic practices and equipment design. This article reviews current recommendations for ergonomic design in the endoscopy procedure space and finds that reported compliance with those recommendations is quite low. Strategies for the management of the risk of musculoskeletal injuries related to the practice of endoscopy include compliance with currently recommended ergonomic practices, education of trainees in ergonomic technique when practicing endoscopy, and research toward the modification and development of more ergonomic endoscopes and procedure spaces.

7 CFR 1773.9 - Disclosure of fraud, illegal acts, and other noncompliance.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., the auditor must design the audit to provide reasonable assurance of detecting fraud that is material... UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE (CONTINUED) POLICY ON AUDITS OF RUS BORROWERS RUS Audit... statements, auditors should apply audit procedures specifically directed to ascertaining whether an illegal...

50 CFR 660.717 - Framework for revising regulations.

Code of Federal Regulations, 2010 CFR

2010-10-01

....717 Section 660.717 Wildlife and Fisheries FISHERY CONSERVATION AND MANAGEMENT, NATIONAL OCEANIC AND... adjust specifications and management measures in accordance with procedures and standards in the FMP. (b... management measures. Consistent with section 3.4 of the FMP, management measures designated as routine may be...

Software for AASHTO LRFD combined shear and torsion computations using modified compression field theory and 3D truss analogy.

DOT National Transportation Integrated Search

2011-10-01

The shear provisions of the AASHTO LRFD Bridge Design Specifications (2008), as well as the simplified : AASHTO procedure for prestressed and non-prestressed reinforced concrete members were investigated and compared : to their equivalent ACI 318-08 ...

Vitamin C: Rate of Decay and Stability Characteristics

ERIC Educational Resources Information Center

Kakis, Frederic J.; Rossi, Carl J.

1974-01-01

Describes an experiment designed to provide the opportunity for studying some of the parameters affecting the stability of Vitamin C in various environments, and to acquaint the student with an experimental procedure for studying simple reaction kinetics and the calculations of specific rate constants. (Author/JR)

15 CFR 923.22 - Areas for preservation or restoration.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Areas for preservation or restoration... preservation or restoration. The management program must include procedures whereby specific areas may be designated for the purpose of preserving or restoring them for their conservation, recreational, ecological...

10 CFR 10.31 - Actions on the recommendations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... DATA OR NATIONAL SECURITY INFORMATION OR AN EMPLOYMENT CLEARANCE Procedures § 10.31 Actions on the... for Corporate Management and Chief Information Officer who has the discretion to return the record to... to specific matters designated by the Deputy Executive Director for Corporate Management and Chief...

10 CFR 10.31 - Actions on the recommendations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... DATA OR NATIONAL SECURITY INFORMATION OR AN EMPLOYMENT CLEARANCE Procedures § 10.31 Actions on the... for Corporate Management and Chief Information Officer who has the discretion to return the record to... to specific matters designated by the Deputy Executive Director for Corporate Management and Chief...

Design and evaluation guidelines for Department of Energy facilities subjected to natural phenomena hazards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kennedy, R.P.; Short, S.A.; McDonald, J.R.

1990-06-01

The Department of Energy (DOE) and the DOE Natural Phenomena Hazards Panel have developed uniform design and evaluation guidelines for protection against natural phenomena hazards at DOE sites throughout the United States. The goal of the guidelines is to assure that DOE facilities can withstand the effects of natural phenomena such as earthquakes, extreme winds, tornadoes, and flooding. The guidelines apply to both new facilities (design) and existing facilities (evaluation, modification, and upgrading). The intended audience is primarily the civil/structural or mechanical engineers conducting the design or evaluation of DOE facilities. The likelihood of occurrence of natural phenomena hazards atmore » each DOE site has been evaluated by the DOE Natural Phenomena Hazard Program. Probabilistic hazard models are available for earthquake, extreme wind/tornado, and flood. Alternatively, site organizations are encouraged to develop site-specific hazard models utilizing the most recent information and techniques available. In this document, performance goals and natural hazard levels are expressed in probabilistic terms, and design and evaluation procedures are presented in deterministic terms. Design/evaluation procedures conform closely to common standard practices so that the procedures will be easily understood by most engineers. Performance goals are expressed in terms of structure or equipment damage to the extent that: (1) the facility cannot function; (2) the facility would need to be replaced; or (3) personnel are endangered. 82 refs., 12 figs., 18 tabs.« less

Manufacturing plastic injection optical molds

NASA Astrophysics Data System (ADS)

Bourque, David

2008-08-01

ABCO Tool & Die, Inc. is a mold manufacturer specializing in the manufacturing of plastic injection molds for molded optical parts. The purpose of this presentation is to explain the concepts and procedures required to build a mold that produces precision optical parts. Optical molds can produce a variety of molded parts ranging from safety eyewear to sophisticated military lens parts, which must meet precise optical specifications. The manufacturing of these molds begins with the design engineering of precision optical components. The mold design and the related optical inserts are determined based upon the specific optical criteria and optical surface geometry. The mold manufacturing techniques will be based upon the optical surface geometry requirements and specific details. Manufacturing processes used will be specific to prescribed geometrical surface requirements of the molded part. The combined efforts result in a robust optical mold which can produce molded parts that meet the most precise optical specifications.

Improving the accuracy of operation coding in surgical discharge summaries

PubMed Central

Martinou, Eirini; Shouls, Genevieve; Betambeau, Nadine

2014-01-01

Procedural coding in surgical discharge summaries is extremely important; as well as communicating to healthcare staff which procedures have been performed, it also provides information that is used by the hospital's coding department. The OPCS code (Office of Population, Censuses and Surveys Classification of Surgical Operations and Procedures) is used to generate the tariff that allows the hospital to be reimbursed for the procedure. We felt that the OPCS coding on discharge summaries was often incorrect within our breast and endocrine surgery department. A baseline measurement over two months demonstrated that 32% of operations had been incorrectly coded, resulting in an incorrect tariff being applied and an estimated loss to the Trust of £17,000. We developed a simple but specific OPCS coding table in collaboration with the clinical coding team and breast surgeons that summarised all operations performed within our department. This table was disseminated across the team, specifically to the junior doctors who most frequently complete the discharge summaries. Re-audit showed 100% of operations were accurately coded, demonstrating the effectiveness of the coding table. We suggest that specifically designed coding tables be introduced across each surgical department to ensure accurate OPCS codes are used to produce better quality surgical discharge summaries and to ensure correct reimbursement to the Trust. PMID:26734286

Health maintenance facility system effectiveness testing

NASA Technical Reports Server (NTRS)

Lloyd, Charles W.; Gosbee, John; Bueker, Richard; Kupra, Debra; Ruta, Mary

1993-01-01

The Medical Simulations Working Group conducted a series of medical simulations to evaluate the proposed Health Maintenance Facility (HMF) Preliminary Design Review (PDR) configuration. The goal of these simulations was to test the system effectiveness of the HMF PDR configurations. The objectives of the medical simulations are to (1) ensure fulfillment of requirements with this HMF design, (2) demonstrate the conformance of the system to human engineering design criteria, and (3) determine whether undesirable design or procedural features were introduced into the design. The simulations consisted of performing 6 different medical scenarios with the HMF mockup in the KRUG laboratory. The scenarios included representative medical procedures and used a broad spectrum of HMF equipment and supplies. Scripts were written and simulations performed by medical simulations working group members under observation from others. Data were collected by means of questionnaires, debriefings, and videotapes. Results were extracted and listed in the individual reports. Specific issues and recommendations from each simulation were compiled into the individual reports. General issues regarding the PDR design of the HMF are outlined in the summary report.

Optimization of an idealized Y-Shaped Extracardiac Fontan Baffle

NASA Astrophysics Data System (ADS)

Yang, Weiguang; Feinstein, Jeffrey; Mohan Reddy, V.; Marsden, Alison

2008-11-01

Research has showed that vascular geometries can significantly impact hemodynamic performance, particularly in pediatric cardiology, where anatomy varies from one patient to another. In this study we optimize a newly proposed design for the Fontan procedure, a surgery used to treat single ventricle heart patients. The current Fontan procedure connects the inferior vena cava (IVC) to the pulmonary arteries (PA's) via a straight Gore-Tex tube, forming a T-shaped junction. In the Y-graft design, the IVC is connected to the left and right PAs by two branches. Initial studies on the Y-graft design showed an increase in efficiency and improvement in flow distribution compared to traditional designs in a single patient-specific model. We now optimize an idealized Y-graft model to refine the design prior to patient testing. A derivate-free optimization algorithm using Kriging surrogate functions and mesh adaptive direct search is coupled to a 3-D finite element Navier-Stokes solver. We will present optimization results for rest and exercise conditions and examine the influence of energy efficiency, wall shear stress, pulsatile flow, and flow distribution on the optimal design.

Multi-objective Optimization of Departure Procedures at Gimpo International Airport

NASA Astrophysics Data System (ADS)

Kim, Junghyun; Lim, Dongwook; Monteiro, Dylan Jonathan; Kirby, Michelle; Mavris, Dimitri

2018-04-01

Most aviation communities have increasing concerns about the environmental impacts, which are directly linked to health issues for local residents near the airport. In this study, the environmental impact of different departure procedures using the Aviation Environmental Design Tool (AEDT) was analyzed. First, actual operational data were compiled at Gimpo International Airport (March 20, 2017) from an open source. Two modifications were made in the AEDT to model the operational circumstances better and the preliminary AEDT simulations were performed according to the acquired operational procedures. Simulated noise results showed good agreements with noise measurement data at specific locations. Second, a multi-objective optimization of departure procedures was performed for the Boeing 737-800. Four design variables were selected and AEDT was linked to a variety of advanced design methods. The results showed that takeoff thrust had the greatest influence and it was found that fuel burn and noise had an inverse relationship. Two points representing each fuel burn and noise optimum on the Pareto front were parsed and run in AEDT to compare with the baseline. The results showed that the noise optimum case reduced Sound Exposure Level 80-dB noise exposure area by approximately 5% while the fuel burn optimum case reduced total fuel burn by 1% relative to the baseline for aircraft-level analysis.

Experimental Investigation of the Axial Impregnation of Oriented Fiber Bundles by Capillary Forces

DTIC Science & Technology

1992-05-01

construed as an official Department of the Army position, unless so designated by other authorized documents. The use of trade names or manufacturers...AND DATES COVERED I May 1992 Final Feb 1988-Mar 1990 4. TITLE AND SUBTITLE 5. FUNDING NUMBERS Eperimental Investigation Of the Axial Impregnation of...will be used.) _____________________ 2. How, specifically, is the report being used? (Information source, design data, procedure, source of ideas, etc

A Comparison of Multivariable Control Design Techniques for a Turbofan Engine Control

NASA Technical Reports Server (NTRS)

Garg, Sanjay; Watts, Stephen R.

1995-01-01

This paper compares two previously published design procedures for two different multivariable control design techniques for application to a linear engine model of a jet engine. The two multivariable control design techniques compared were the Linear Quadratic Gaussian with Loop Transfer Recovery (LQG/LTR) and the H-Infinity synthesis. The two control design techniques were used with specific previously published design procedures to synthesize controls which would provide equivalent closed loop frequency response for the primary control loops while assuring adequate loop decoupling. The resulting controllers were then reduced in order to minimize the programming and data storage requirements for a typical implementation. The reduced order linear controllers designed by each method were combined with the linear model of an advanced turbofan engine and the system performance was evaluated for the continuous linear system. Included in the performance analysis are the resulting frequency and transient responses as well as actuator usage and rate capability for each design method. The controls were also analyzed for robustness with respect to structured uncertainties in the unmodeled system dynamics. The two controls were then compared for performance capability and hardware implementation issues.

Microseismic monitoring of Chocolate Bayou, Texas: the Pleasant Bayou No. 2 geopressured/geothermal energy test well program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mauk, F.J.; Kimball, B.; Davis, R.A.

1984-01-01

The Brazoria seismic network, instrumentation, design, and specifications are described. The data analysis procedures are presented. Seismicity is described in relation to the Pleasant Bayou production history. Seismicity originating near the chemical plant east of the geopressured/geothermal well is discussed. (MHR)

Construction of a remotely sensed area sampling frame for Southern Brazil

NASA Technical Reports Server (NTRS)

Fecso, R.; Gardner, W.; Hale, B.; Johnson, V.; Pavlasek, S. (Principal Investigator)

1982-01-01

A remotely sensed area sampling frame was constructed for selected areas in Southern Brazil. The sampling unit information was stored in digital form in a latitudinal/longitudinal characterized population. Computerized sampling procedures were developed which allow for flexibility in sample unit specifications and sampling designs.

AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT XXV, MICHIGAN/CLARK TRANSMISSION--TROUBLESHOOTING.

ERIC Educational Resources Information Center

Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF TROUBLESHOOTING PROCEDURES FOR A SPECIFIC TRANSMISSION USED ON DIESEL POWERED EQUIPMENT. TOPICS ARE (1) PRELIMINARY CHECKS, (2) PRESSURE AND OIL FLOW CHECKS, (3) TROUBLESHOOTING TABLES, (4) TROUBLESHOOTING VEHICLES UNDER FIELD CONDITIONS, AND (5) ANALYZING UNACCEPTABLE…

"Madame Bovary": Illusion and Reality. [Lesson Plan].

ERIC Educational Resources Information Center

Carangelo, Audrey

Based on Gustave Flaubert's novel "Madame Bovary," this lesson plan presents activities designed to help students explore the theme of "illusion versus reality" in the novel; identify and list alternate themes in the novel; and cite specific examples of illusion versus reality from the novel. It includes objectives, materials, procedures,…

Health Instruction Packages: Specific Nursing Skills.

ERIC Educational Resources Information Center

Bates, Clarice; And Others

Text, illustrations, and exercises are utilized in a set of five learning modules designed to instruct nursing students in a variety of clinical skills. The first module, "Down the Tube: Insertion of a Nasogastric Tube" by Clarice Bates, describes materials and procedures used to insert a nasogastric tube through the nose and esophagus…

Organizational Justice and Employee Satisfaction in Performance Appraisal

ERIC Educational Resources Information Center

Palaiologos, Anastasios; Papazekos, Panagiotis; Panayotopoulou, Leda

2011-01-01

Purpose: This paper aims to explore the performance appraisal (PA) aspects that are connected with organizational justice, and more specifically three kinds of justice, namely distributive, procedural and interactional justice. Design/methodology/approach: The research is based on a sample of 170 respondents who answered a questionnaire giving…

Using Positive Behavior Support to Design Effective Classrooms

ERIC Educational Resources Information Center

Anderson, Cynthia M.; Spaulding, Scott A.

2007-01-01

A number of evidence-based classroom management approaches, procedures, and programs have been developed and presented over the years. In this article the authors synthesize recommendations from various sources, focusing on evidence-based strategies that can be implemented in a systematic manner. They focus specifically on universal strategies,…

After the Clinic What?

ERIC Educational Resources Information Center

Walker, Laurens; Goldstein, Burton

1976-01-01

Noting the limitations of clinical legal education when it focuses only on the learning of practical skills outside the classroom, the authors describe an experimental course in civil procedure designed to adapt clinical methods to the classroom by placing each student in the role of the lawyer in a specific case with class presentations and…

Project PARTnership: Instructional Kit. A Model Program for Encouraging Self-Determination through Access to the Arts.

ERIC Educational Resources Information Center

Harris, Carolyn DeMeyer, Ed.; McKinney, David D., Ed.

This instructional kit outlines procedures for implementing Project PARTnership, a program for teaching students with disabilities greater self-determination skills through specifically designed arts experiences. An introductory section describes key project activities, including establishing a site steering committee comprised of teachers,…

Microseismic monitoring of Chocolate Bayou, Texas: The Pleasant Bayou no. 2 geopressured/geothermal energy test well program

NASA Astrophysics Data System (ADS)

Mauk, F. J.; Kimball, B.; Davis, R. A.

The Brazoria seismic network, instrumentation, design, and specifications are described. The data analysis procedures are presented. Seismicity is described in relation to the Pleasant Bayou production history. Seismicity originating near the chemical plant east of the geopressured/geothermal well is discussed.

40 CFR 86.308-79 - Gas specifications.

Code of Federal Regulations, 2012 CFR

2012-07-01

... New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test Procedures § 86.308-79... Diesel engine tests the diluent shall be zero-grade air. (3) Calibration or span gases for the NOX...) Alternate pure hydrogen fuel. Some HFID's are designed to operate on pure hydrogen. Generally the HFID fuel...

40 CFR 86.308-79 - Gas specifications.

Code of Federal Regulations, 2013 CFR

2013-07-01

... New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test Procedures § 86.308-79... Diesel engine tests the diluent shall be zero-grade air. (3) Calibration or span gases for the NOX...) Alternate pure hydrogen fuel. Some HFID's are designed to operate on pure hydrogen. Generally the HFID fuel...

76 FR 60557 - Agency Information Collection Activities: Submission for the Office of Management and Budget (OMB...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-29

... purposes in research, industry, and other fields. The subparts cover specific requirements for obtaining a license or license exemption, design and performance criteria for irradiators; and radiation safety... emergency procedures, personnel monitoring, radiation surveys, inspection, and maintenance. Part 36 also...

Software for AASHTO LRFD combined shear and torsion computations using modified compression field theory and 3D truss analogy : technical summary.

DOT National Transportation Integrated Search

2011-10-01

The shear provisions of the AASHTO LRFD Bridge Design Specifications (2008), as well as the simplified AASHTO procedure for prestressed and non-prestressed reinforced concrete members were investigated and compared to their equivalent ACI 318-08 prov...

Photovoltaic system criteria documents. Volume 5: Safety criteria for photovoltaic applications

NASA Technical Reports Server (NTRS)

Koenig, John C.; Billitti, Joseph W.; Tallon, John M.

1979-01-01

Methodology is described for determining potential safety hazards involved in the construction and operation of photovoltaic power systems and provides guidelines for the implementation of safety considerations in the specification, design and operation of photovoltaic systems. Safety verification procedures for use in solar photovoltaic systems are established.

40 CFR 2.102 - Procedures for making requests.

Code of Federal Regulations, 2010 CFR

2010-07-01

... envelope or e-mail subject line “Freedom of Information Act Request.” You should also include your name... request should include specific information about each record sought, such as the date, title or name, author, recipient, and subject matter. If known, you should include any file designations or descriptions...

40 CFR 2.102 - Procedures for making requests.

Code of Federal Regulations, 2011 CFR

2011-07-01

... envelope or e-mail subject line “Freedom of Information Act Request.” You should also include your name... request should include specific information about each record sought, such as the date, title or name, author, recipient, and subject matter. If known, you should include any file designations or descriptions...

RANDOMIZATION PROCEDURES FOR THE ANALYSIS OF EDUCATIONAL EXPERIMENTS.

ERIC Educational Resources Information Center

COLLIER, RAYMOND O.

CERTAIN SPECIFIC ASPECTS OF HYPOTHESIS TESTS USED FOR ANALYSIS OF RESULTS IN RANDOMIZED EXPERIMENTS WERE STUDIED--(1) THE DEVELOPMENT OF THE THEORETICAL FACTOR, THAT OF PROVIDING INFORMATION ON STATISTICAL TESTS FOR CERTAIN EXPERIMENTAL DESIGNS AND (2) THE DEVELOPMENT OF THE APPLIED ELEMENT, THAT OF SUPPLYING THE EXPERIMENTER WITH MACHINERY FOR…

Toms River Drivers Manual 1984-1985.

ERIC Educational Resources Information Center

Thomas, Patricia

The procedures in this manual are designed to establish stability and continuity within the student transportation department of the Toms River Regional Schools in New Jersey. The manual is divided into three sections. Section 1 provides driver and aide specific information. It includes directives related to time clock, spare buses, and…

Reports of the National Juvenile Justice Assessment Centers. Juvenile Delinquency Prevention Experiments: A Review and Analysis.

ERIC Educational Resources Information Center

Berleman, William C.

Ten delinquency prevention studies are reviewed that incorporated rigorous evaluative procedures (specifically the classic experimental design) for assessing programmatic outcomes. Following an introduction, the evaluation mechanisms built into each project are described, since they were used for determination of the effectiveness of the…

An Interdisciplinary Approach to the Teaching of Foreign Literature

ERIC Educational Resources Information Center

Davidheiser, James C.

1977-01-01

The Integrated Learning Semester program at the University of Delaware is described. Courses were designed around themes touching several academic areas and instructors cooperated in teaching courses. A course in literature and music of Romanticism is outlined and specific problems and procedures for implementing a program are noted. (CHK)

Hypothesis tests for stratified mark-specific proportional hazards models with missing covariates, with application to HIV vaccine efficacy trials.

PubMed

Sun, Yanqing; Qi, Li; Yang, Guangren; Gilbert, Peter B

2018-05-01

This article develops hypothesis testing procedures for the stratified mark-specific proportional hazards model with missing covariates where the baseline functions may vary with strata. The mark-specific proportional hazards model has been studied to evaluate mark-specific relative risks where the mark is the genetic distance of an infecting HIV sequence to an HIV sequence represented inside the vaccine. This research is motivated by analyzing the RV144 phase 3 HIV vaccine efficacy trial, to understand associations of immune response biomarkers on the mark-specific hazard of HIV infection, where the biomarkers are sampled via a two-phase sampling nested case-control design. We test whether the mark-specific relative risks are unity and how they change with the mark. The developed procedures enable assessment of whether risk of HIV infection with HIV variants close or far from the vaccine sequence are modified by immune responses induced by the HIV vaccine; this question is interesting because vaccine protection occurs through immune responses directed at specific HIV sequences. The test statistics are constructed based on augmented inverse probability weighted complete-case estimators. The asymptotic properties and finite-sample performances of the testing procedures are investigated, demonstrating double-robustness and effectiveness of the predictive auxiliaries to recover efficiency. The finite-sample performance of the proposed tests are examined through a comprehensive simulation study. The methods are applied to the RV144 trial. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Interventional spine and pain procedures in patients on antiplatelet and anticoagulant medications: guidelines from the American Society of Regional Anesthesia and Pain Medicine, the European Society of Regional Anaesthesia and Pain Therapy, the American Academy of Pain Medicine, the International Neuromodulation Society, the North American Neuromodulation Society, and the World Institute of Pain.

PubMed

Narouze, Samer; Benzon, Honorio T; Provenzano, David A; Buvanendran, Asokumar; De Andres, José; Deer, Timothy R; Rauck, Richard; Huntoon, Marc A

2015-01-01

Interventional spine and pain procedures cover a far broader spectrum than those for regional anesthesia, reflecting diverse targets and goals. When surveyed, interventional pain and spine physicians attending the American Society of Regional Anesthesia and Pain Medicine (ASRA) 11th Annual Pain Medicine Meeting exhorted that existing ASRA guidelines for regional anesthesia in patients on antiplatelet and anticoagulant medications were insufficient for their needs. Those surveyed agreed that procedure-specific and patient-specific factors necessitated separate guidelines for pain and spine procedures. In response, ASRA formed a guidelines committee. After preliminary review of published complication reports and studies, committee members stratified interventional spine and pain procedures according to potential bleeding risk as low-, intermediate-, and high-risk procedures. The ASRA guidelines were deemed largely appropriate for the low- and intermediate-risk categories, but it was agreed that the high-risk targets required an intensive look at issues specific to patient safety and optimal outcomes in pain medicine. The latest evidence was sought through extensive database search strategies and the recommendations were evidence-based when available and pharmacology-driven otherwise. We could not provide strength and grading of these recommendations as there are not enough well-designed large studies concerning interventional pain procedures to support such grading. Although the guidelines could not always be based on randomized studies or on large numbers of patients from pooled databases, it is hoped that they will provide sound recommendations and the evidentiary basis for such recommendations.

Towards Verification of Operational Procedures Using Auto-Generated Diagnostic Trees

NASA Technical Reports Server (NTRS)

Kurtoglu, Tolga; Lutz, Robyn; Patterson-Hine, Ann

2009-01-01

The design, development, and operation of complex space, lunar and planetary exploration systems require the development of general procedures that describe a detailed set of instructions capturing how mission tasks are performed. For both crewed and uncrewed NASA systems, mission safety and the accomplishment of the scientific mission objectives are highly dependent on the correctness of procedures. In this paper, we describe how to use the auto-generated diagnostic trees from existing diagnostic models to improve the verification of standard operating procedures. Specifically, we introduce a systematic method, namely the Diagnostic Tree for Verification (DTV), developed with the goal of leveraging the information contained within auto-generated diagnostic trees in order to check the correctness of procedures, to streamline the procedures in terms of reducing the number of steps or use of resources in them, and to propose alternative procedural steps adaptive to changing operational conditions. The application of the DTV method to a spacecraft electrical power system shows the feasibility of the approach and its range of capabilities

Type I error probabilities based on design-stage strategies with applications to noninferiority trials.

PubMed

Rothmann, Mark

2005-01-01

When testing the equality of means from two different populations, a t-test or large sample normal test tend to be performed. For these tests, when the sample size or design for the second sample is dependent on the results of the first sample, the type I error probability is altered for each specific possibility in the null hypothesis. We will examine the impact on the type I error probabilities for two confidence interval procedures and procedures using test statistics when the design for the second sample or experiment is dependent on the results from the first sample or experiment (or series of experiments). Ways for controlling a desired maximum type I error probability or a desired type I error rate will be discussed. Results are applied to the setting of noninferiority comparisons in active controlled trials where the use of a placebo is unethical.

Macroergonomic study of food sector company distribution centres.

PubMed

García Acosta, Gabriel; Lange Morales, Karen

2008-07-01

This study focussed on the work system design to be used by a Colombian food sector company for distributing products. It considered the concept of participative ergonomics, where people from the commercial, logistics, operation, occupational health areas worked in conjunction with the industrial designers, ergonomists who methodologically led the project. As a whole, the project was conceived as having five phases: outline, diagnosis, modelling the process, scalability, instrumentation. The results of the project translate into procedures for selecting, projecting a new distribution centre, the operational process model, a description of ergonomic systems that will enable specific work stations to be designed, the procedure for adapting existing warehouses. Strategically, this work helped optimise the company's processes and ensure that knowledge would be transferred within it. In turn, it became a primary prevention strategy in the field of health, aimed at reducing occupational risks, improving the quality of life at work.

The analysis of tensegrity structures for the design of a morphing wing

NASA Astrophysics Data System (ADS)

Moored, Keith W., III; Bart-Smith, Hilary

2005-05-01

Tensegrity structures have become of engineering interest in recent years, but very few have found practical use. This lack of integration is attributed to the lack of a well formulated design procedure. In this paper, a preliminary procedure is presented for developing morphing tensegrity structures that include actuating elements. To do this, the virtual work method has been modified to allow for individual actuation of struts and cables. A generalized connectivity matrix for a cantilever beam constructed from either a single 4-strut cell or multiple 4-strut cells has been developed. Global deflections resulting from actuation of specific elements have been calculated. Furthermore, the force density method is expanded to include a necessary upper bound condition such that a physically feasible structure can be designed. Finally, the importance of relative force density values on the overall shape of a structure comprising of multiple unit cells is discussed.

Plasma Chamber Design and Fabrication Activities

NASA Astrophysics Data System (ADS)

Parodi, B.; Bianchi, A.; Cucchiaro, A.; Coletti, A.; Frosi, P.; Mazzone, G.; Pizzuto, A.; Ramogida, G.; Coppi, B.

2006-10-01

A fabrication procedure for a typical Plasma Chamber (PC) sector has been developed to cover all the manufacturing phases, from the raw materials specification (including metallurgical processes) to the machining operations, acceptance procedures and vacuum tests. Basically, the sector is made of shaped elements (forged or rolled) welded together using special fixtures and then machined to achieve the final dimensional accuracy. An upgraded design of the plasma chamber's vertical support that can withstand the estimated electromagnetic loads (Eddy and Halo current plus horizontal net force resulting from the worst plasma disruption scenario VDE, Vertical Displacement Event) has been completed. The maintenance of the radial support can take place hands-on with a direct access from outside the cryostat. With the present design, vacuum tightness is achieved by welding conducted with automatic welding heads. On the outer surface of the PC a dedicated duct system, filled by helium gas, is included to cool down the PC to room temperature when needed.

Notes on testing non-inferiority under the partial verification design with a confirmatory procedure limited to screen positives.

PubMed

Lui, Kung-Jong

2012-05-01

When a new test with fewer invasions or less expenses to administer than the traditional test is developed, we may be interested in testing whether the former is non-inferior to the latter with respect to test accuracy. We define non-inferiority via both the odds ratio (OR) of correctly identifying a case and the OR of correctly identifying a non-case between two tests under comparison. We focus our discussion on testing the non-inferiority of a new screening test to a traditional screening test when a confirmatory procedure is performed only on patients with screen positives. On the basis of well-established methods for paired-sample data, we derive an asymptotic test procedure and an exact test procedure with respect to the two ORs defined here. Using Monte Carlo simulation, we evaluate the performance of these test procedures in a variety of situations. We note that the test procedures proposed here can also be applicable if we are interested in testing non-inferiority with respect to the ratio of sensitivities and the ratio of specificities. We discuss interval estimation of these ORs and sample size calculation based on the asymptotic test procedure considered here. We use the data taken from a study of the prostate-specific-antigen (PSA) test and the digital rectal examination (DRE) test to illustrate the practical use of these test procedures, interval estimators and sample size calculation formula. Copyright © 2012 Elsevier Inc. All rights reserved.

Evaluation and improvement of micro-surfacing mix design method and modelling of asphalt emulsion mastic in terms of filler-emulsion interaction

NASA Astrophysics Data System (ADS)

Robati, Masoud

This Doctorate program focuses on the evaluation and improving the rutting resistance of micro-surfacing mixtures. There are many research problems related to the rutting resistance of micro-surfacing mixtures that still require further research to be solved. The main objective of this Ph.D. program is to experimentally and analytically study and improve rutting resistance of micro-surfacing mixtures. During this Ph.D. program major aspects related to the rutting resistance of micro-surfacing mixtures are investigated and presented as follow: 1) evaluation of a modification of current micro-surfacing mix design procedures: On the basis of this effort, a new mix design procedure is proposed for type III micro-surfacing mixtures as rut-fill materials on the road surface. Unlike the current mix design guidelines and specification, the new mix design is capable of selecting the optimum mix proportions for micro-surfacing mixtures; 2) evaluation of test methods and selection of aggregate grading for type III application of micro-surfacing: Within the term of this study, a new specification for selection of aggregate grading for type III application of micro-surfacing is proposed; 3) evaluation of repeatability and reproducibility of micro-surfacing mixture design tests: In this study, limits for repeatability and reproducibility of micro-surfacing mix design tests are presented; 4) a new conceptual model for filler stiffening effect on asphalt mastic of micro-surfacing: A new model is proposed, which is able to establish limits for minimum and maximum filler concentrations in the micro-surfacing mixture base on only the filler important physical and chemical properties; 5) incorporation of reclaimed asphalt pavement and post-fabrication asphalt shingles in micro-surfacing mixture: The effectiveness of newly developed mix design procedure for micro-surfacing mixtures is further validated using recycled materials. The results present the limits for the use of RAP and RAS amount in micro-surfacing mixtures; 6) new colored micro-surfacing formulations with improved durability and performance: The significant improvement of around 45% in rutting resistance of colored and conventional micro-surfacing mixtures is achieved through employing low penetration grade bitumen polymer modified asphalt emulsion stabilized using nanoparticles.

Processor architectures utilizing magnetic bubble and semi-conductor memories. [for the Omega navigation system

NASA Technical Reports Server (NTRS)

Parrish, E. A., Jr.; Aylor, J. H.

1975-01-01

To aid work being conducted on the feasibility of a low cost Omega navigational receiver, a control panel was designed and constructed according to supplied specifications. Since the proposed Omega receiver is designed around a microprocessor, software engineering necessary for control panel operation is included in the design. The control panel is to be used as an operational model for use in the design of a prototype receiver. A detailed description of the hardware design is presented along with a description of the software needed to operate the panel. A complete description of the operating procedures for the panel are also included.

Project W-314 acceptance test report HNF-4647 for HNF-4646 241-B pit leak detection ANB-WT-LDSTA-231 for project W-314

DOE Office of Scientific and Technical Information (OSTI.GOV)

HAMMERS, J.S.

The purpose of the test was to verify that the AN Tank Farm B Pit Leak Detector components are functionally integrated and operate in accordance with engineering design specifications. The Acceptance Test Procedure HNF-4646,241-AN-B-Pit Leak Detection ANB-WT-LDSTA-231 was conducted between 26 June and 02 July 1999 at the 200E AN Tank Farm. The test has been completed with no open test exceptions. The test was conducted prior to final engineering ''as built'' activities being completed this had no impact on the procedure or test results. All components, identified in the procedure were found to be labeled and identified as writtenmore » in the procedure.« less

Flexibility in Flood Management Design: Proactive Planning Under Climate Change Uncertainty

NASA Astrophysics Data System (ADS)

Smet, K.; de Neufville, R.; van der Vlist, M.

2015-12-01

This paper presents an innovative, value-enhancing procedure for effective planning and design of long-lived flood management infrastructure given uncertain future flooding threats due to climate change. Designing infrastructure that can be adapted over time is a method to safeguard the efficacy of current design decisions given uncertainty about rates and future impacts of climate change. This paper explores the value of embedding "options" in a physical structure, where an option is the right but not the obligation to do something at a later date (e.g. over-dimensioning a floodwall foundation now facilitates a future height addition in response to observed increases in sea level; building of extra pump bays in a pumping station now enables the addition of pumping capacity whenever increased precipitation warrants an expansion.) The proposed procedure couples a simulation model that captures future climate induced changes to the hydrologic operating environment of a structure, with an economic model that estimates the lifetime economic performance of alternative investments. The economic model uses Real "In" Options analysis, a type of cash flow analysis that quantifies the implicit value of options and the flexibility they provide. This procedure is demonstrated using replacement planning for the multi-functional pumping station IJmuiden on the North Sea Canal in the Netherlands. Flexibility in design decisions is modelled, varying the size and specific options included in the new structure. Results indicate that the incorporation of options within the structural design has the potential to improve its economic performance, as compared to more traditional, "build it once and build it big" designs where flexibility is not an explicit design criterion. The added value resulting from the incorporation of flexibility varies with the range of future conditions considered, as well as the options examined. This procedure could be applied more broadly to explore investment strategies for the design of other flood management structures.

Millimeter-wave antenna design

NASA Technical Reports Server (NTRS)

Leighton, R. B.

1977-01-01

Problems and opportunities are discussed for adapting certain design features and construction techniques, developed for producing high accuracy ground based radio dishes, to producing milimeter wave dishes for space use. Specifically considered is a foldable telescope of 24 m aperture and 9.6 m focal length, composed of 37 rigid hexagonal panels, which will fit within the 4.5 m diameter x 18 m long payload limits of space shuttle. As here conceived, the telescope would be a free flyer with its own power and pointing systems. Some of the structural design features and construction procedures are considered.

Design of Composite Structures Using Knowledge-Based and Case Based Reasoning

NASA Technical Reports Server (NTRS)

Lambright, Jonathan Paul

1996-01-01

A method of using knowledge based and case based reasoning to assist designers during conceptual design tasks of composite structures was proposed. The cooperative use of heuristics, procedural knowledge, and previous similar design cases suggests a potential reduction in design cycle time and ultimately product lead time. The hypothesis of this work is that the design process of composite structures can be improved by using Case-Based Reasoning (CBR) and Knowledge-Based (KB) reasoning in the early design stages. The technique of using knowledge-based and case-based reasoning facilitates the gathering of disparate information into one location that is easily and readily available. The method suggests that the inclusion of downstream life-cycle issues into the conceptual design phase reduces potential of defective, and sub-optimal composite structures. Three industry experts were interviewed extensively. The experts provided design rules, previous design cases, and test problems. A Knowledge Based Reasoning system was developed using the CLIPS (C Language Interpretive Procedural System) environment and a Case Based Reasoning System was developed using the Design Memory Utility For Sharing Experiences (MUSE) xviii environment. A Design Characteristic State (DCS) was used to document the design specifications, constraints, and problem areas using attribute-value pair relationships. The DCS provided consistent design information between the knowledge base and case base. Results indicated that the use of knowledge based and case based reasoning provided a robust design environment for composite structures. The knowledge base provided design guidance from well defined rules and procedural knowledge. The case base provided suggestions on design and manufacturing techniques based on previous similar designs and warnings of potential problems and pitfalls. The case base complemented the knowledge base and extended the problem solving capability beyond the existence of limited well defined rules. The findings indicated that the technique is most effective when used as a design aid and not as a tool to totally automate the composites design process. Other areas of application and implications for future research are discussed.

Shaping electromagnetic waves using software-automatically-designed metasurfaces.

PubMed

Zhang, Qian; Wan, Xiang; Liu, Shuo; Yuan Yin, Jia; Zhang, Lei; Jun Cui, Tie

2017-06-15

We present a fully digital procedure of designing reflective coding metasurfaces to shape reflected electromagnetic waves. The design procedure is completely automatic, controlled by a personal computer. In details, the macro coding units of metasurface are automatically divided into several types (e.g. two types for 1-bit coding, four types for 2-bit coding, etc.), and each type of the macro coding units is formed by discretely random arrangement of micro coding units. By combining an optimization algorithm and commercial electromagnetic software, the digital patterns of the macro coding units are optimized to possess constant phase difference for the reflected waves. The apertures of the designed reflective metasurfaces are formed by arranging the macro coding units with certain coding sequence. To experimentally verify the performance, a coding metasurface is fabricated by automatically designing two digital 1-bit unit cells, which are arranged in array to constitute a periodic coding metasurface to generate the required four-beam radiations with specific directions. Two complicated functional metasurfaces with circularly- and elliptically-shaped radiation beams are realized by automatically designing 4-bit macro coding units, showing excellent performance of the automatic designs by software. The proposed method provides a smart tool to realize various functional devices and systems automatically.

High-level PC-based laser system modeling

NASA Astrophysics Data System (ADS)

Taylor, Michael S.

1991-05-01

Since the inception of the Strategic Defense Initiative (SDI) there have been a multitude of comparison studies done in an attempt to evaluate the effectiveness and relative sizes of complementary, and sometimes competitive, laser weapon systems. It became more and more apparent that what the systems analyst needed was not only a fast, but a cost effective way to perform high-level trade studies. In the present investigation, a general procedure is presented for the development of PC-based algorithmic systems models for laser systems. This procedure points out all of the major issues that should be addressed in the design and development of such a model. Issues addressed include defining the problem to be modeled, defining a strategy for development, and finally, effective use of the model once developed. Being a general procedure, it will allow a systems analyst to develop a model to meet specific needs. To illustrate this method of model development, a description of the Strategic Defense Simulation - Design To (SDS-DT) model developed and used by Science Applications International Corporation (SAIC) is presented. SDS-DT is a menu-driven, fast executing, PC-based program that can be used to either calculate performance, weight, volume, and cost values for a particular design or, alternatively, to run parametrics on particular system parameters to perhaps optimize a design.

Optimal Synthesis of Compliant Mechanisms using Subdivision and Commercial FEA (DETC2004-57497)

NASA Technical Reports Server (NTRS)

Hull, Patrick V.; Canfield, Stephen

2004-01-01

The field of distributed-compliance mechanisms has seen significant work in developing suitable topology optimization tools for their design. These optimal design tools have grown out of the techniques of structural optimization. This paper will build on the previous work in topology optimization and compliant mechanism design by proposing an alternative design space parameterization through control points and adding another step to the process, that of subdivision. The control points allow a specific design to be represented as a solid model during the optimization process. The process of subdivision creates an additional number of control points that help smooth the surface (for example a C(sup 2) continuous surface depending on the method of subdivision chosen) creating a manufacturable design free of some traditional numerical instabilities. Note that these additional control points do not add to the number of design parameters. This alternative parameterization and description as a solid model effectively and completely separates the design variables from the analysis variables during the optimization procedure. The motivation behind this work is to create an automated design tool from task definition to functional prototype created on a CNC or rapid-prototype machine. This paper will describe the proposed compliant mechanism design process and will demonstrate the procedure on several examples common in the literature.

Reverse Shoulder Arthroplasty Prosthesis Design Classification System.

PubMed

Routman, Howard D; Flurin, Pierre-Henri; Wright, Thomas W; Zuckerman, Joseph D; Hamilton, Matthew A; Roche, Christopher P

2015-12-01

Multiple different reverse total shoulder arthroplasty (rTSA) prosthesis designs are available in the global marketplace for surgeons to perform this growing procedure. Subtle differences in rTSA prosthesis design parameters have been shown to have significant biomechanical impact and clinical consequences. We propose an rTSA prosthesis design classification system to objectively identify and categorize different designs based upon their specific glenoid and humeral prosthetic characteristics for the purpose of standardizing nomenclature that will help the orthopaedic surgeon determine which combination of design configurations best suit a given clinical scenario. The impact of each prosthesis classification type on shoulder muscle length and deltoid wrapping are also described to illustrate how each prosthesis classification type impacts these biomechanical parameters.

A Highly Flexible, Automated System Providing Reliable Sample Preparation in Element- and Structure-Specific Measurements.

PubMed

Vorberg, Ellen; Fleischer, Heidi; Junginger, Steffen; Liu, Hui; Stoll, Norbert; Thurow, Kerstin

2016-10-01

Life science areas require specific sample pretreatment to increase the concentration of the analytes and/or to convert the analytes into an appropriate form for the detection and separation systems. Various workstations are commercially available, allowing for automated biological sample pretreatment. Nevertheless, due to the required temperature, pressure, and volume conditions in typical element and structure-specific measurements, automated platforms are not suitable for analytical processes. Thus, the purpose of the presented investigation was the design, realization, and evaluation of an automated system ensuring high-precision sample preparation for a variety of analytical measurements. The developed system has to enable system adaption and high performance flexibility. Furthermore, the system has to be capable of dealing with the wide range of required vessels simultaneously, allowing for less cost and time-consuming process steps. However, the system's functionality has been confirmed in various validation sequences. Using element-specific measurements, the automated system was up to 25% more precise compared to the manual procedure and as precise as the manual procedure using structure-specific measurements. © 2015 Society for Laboratory Automation and Screening.

Design of piezoelectric transformer for DC/DC converter with stochastic optimization method

NASA Astrophysics Data System (ADS)

Vasic, Dejan; Vido, Lionel

2016-04-01

Piezoelectric transformers were adopted in recent year due to their many inherent advantages such as safety, no EMI problem, low housing profile, and high power density, etc. The characteristics of the piezoelectric transformers are well known when the load impedance is a pure resistor. However, when piezoelectric transformers are used in AC/DC or DC/DC converters, there are non-linear electronic circuits connected before and after the transformer. Consequently, the output load is variable and due to the output capacitance of the transformer the optimal working point change. This paper starts from modeling a piezoelectric transformer connected to a full wave rectifier in order to discuss the design constraints and configuration of the transformer. The optimization method adopted here use the MOPSO algorithm (Multiple Objective Particle Swarm Optimization). We start with the formulation of the objective function and constraints; then the results give different sizes of the transformer and the characteristics. In other word, this method is looking for a best size of the transformer for optimal efficiency condition that is suitable for variable load. Furthermore, the size and the efficiency are found to be a trade-off. This paper proposes the completed design procedure to find the minimum size of PT in need. The completed design procedure is discussed by a given specification. The PT derived from the proposed design procedure can guarantee both good efficiency and enough range for load variation.

System design package for IBM system one: solar heating and domestic hot water

NASA Technical Reports Server (NTRS)

1977-01-01

This report is a collation of documents and drawings that describe a prototype solar heating and hot water system using air as the collector fluid and a pebble bed for heat storage. The system was designed for installation into a single family dwelling. The description, performance specification, subsystem drawings, verification plan/procedure, and hazard analysis of the system was packaged for evaluation of the system with information sufficient to assemble a similar system.

System Design Package for SIMS Prototype System 3, Solar Heating and Domestic Hot Water

NASA Technical Reports Server (NTRS)

1978-01-01

A collation of documents and drawings are presented that describe a prototype solar heating and hot water system using liquid flat plate collectors and a gas or electric furnace energy subsystem. The system was designed for installation into a single-family dwelling. The description, performance specification, subsystem drawings, verification plan/procedure, and hazard analysis of the system are packaged for evaluation of the system with information sufficient to assemble a similar system.

Towards sensible toxicity testing for nanomaterials: proposal for the specification of test design

NASA Astrophysics Data System (ADS)

Potthoff, Annegret; Weil, Mirco; Meißner, Tobias; Kühnel, Dana

2015-12-01

During the last decade, nanomaterials (NM) were extensively tested for potential harmful effects towards humans and environmental organisms. However, a sound hazard assessment was so far hampered by uncertainties and a low comparability of test results. The reason for the low comparability is a high variation in the (1) type of NM tested with regard to raw material, size and shape and (2) procedures before and during the toxicity testing. This calls for tailored, nanomaterial-specific protocols. Here, a structured approach is proposed, intended to lead to test protocols not only tailored to specific types of nanomaterials, but also to respective test system for toxicity testing. There are existing standards on single procedures involving nanomaterials, however, not all relevant procedures are covered by standards. Hence, our approach offers a detailed way of weighting several plausible alternatives for e.g. sample preparation, in order to decide on the procedure most meaningful for a specific nanomaterial and toxicity test. A framework of several decision trees (DT) and flow charts to support testing of NM is proposed as a basis for further refinement and in-depth elaboration. DT and flow charts were drafted for (1) general procedure—physicochemical characterisation, (2) choice of test media, (3) decision on test scenario and application of NM to liquid media, (4) application of NM to the gas phase, (5) application of NM to soil and sediments, (6) dose metrics, (S1) definition of a nanomaterial, and (S2) dissolution. The applicability of the proposed approach was surveyed by using experimental data retrieved from studies on nanoscale CuO. This survey demonstrated the DT and flow charts to be a convenient tool to systematically decide upon test procedures and processes, and hence pose an important step towards harmonisation of NM testing.

Aerodynamic design of axisymmetric hypersonic wind-tunnel nozzles using least-squares/parabolized Navier-Stokes procedure

NASA Technical Reports Server (NTRS)

Korte, John J.

1992-01-01

A new procedure unifying the best of present classical design practices, CFD and optimization procedures, is demonstrated for designing the aerodynamic lines of hypersonic wind tunnel nozzles. This procedure can be employed to design hypersonic wind tunnel nozzles with thick boundary layers where the classical design procedure has been demonstrated to break down. Advantages of this procedure allow full utilization of powerful CFD codes in the design process, solves an optimization problem to determine the new contour, may be used to design new nozzles or improve sections of existing nozzles, and automatically compensates the nozzle contour for viscous effects as part of the unified design procedure.

New procedure to reduce the time and cost of broncho-pulmonary specimen management using the Previ Isola® automated inoculation system.

PubMed

Nebbad-Lechani, Biba; Emirian, Aurélie; Maillebuau, Fabienne; Mahjoub, Nadia; Fihman, Vincent; Legrand, Patrick; Decousser, Jean-Winoc

2013-12-01

The microbiological diagnosis of respiratory tract infections requires serial manual dilutions of the clinical specimen before agar plate inoculation, disrupting the workflow in bacteriology clinical laboratories. Automated plating instrument systems have been designed to increase the speed, reproducibility and safety of this inoculating step; nevertheless, data concerning respiratory specimens are lacking. We tested a specific procedure that uses the Previ Isola® (bioMérieux, Craponne, France) to inoculate with broncho-pulmonary specimens (BPS). A total of 350 BPS from a university-affiliated hospital were managed in parallel using the manual reference and the automated methods (expectoration: 75; broncho-alveolar lavage: 68; tracheal aspiration: 17; protected distal sample: 190). A specific enumeration reading grid, a pre-liquefaction step and a fluidity test, performed before the inoculation, were designed for the automated method. The qualitative (i.e., the number of specimens yielding a bacterial count greater than the clinical threshold) and quantitative (i.e., the discrepancy within a 0.5 log value) concordances were 100% and 98.2%, respectively. The slimmest subgroup of expectorations could not be managed by the automated method (8%, 6/75). The technical time and cost savings (i.e., number of consumed plates) reached 50%. Additional studies are required for specific populations, such as cystic fibrosis specimens and associated bacterial variants. An automated decapper should be implemented to increase the biosafety of the process. The PREVI Isola® adapted procedure is a time- and cost-saving method for broncho-pulmonary specimen processing. © 2013.

Flood Catastrophe Model for Designing Optimal Flood Insurance Program: Estimating Location-Specific Premiums in the Netherlands.

PubMed

Ermolieva, T; Filatova, T; Ermoliev, Y; Obersteiner, M; de Bruijn, K M; Jeuken, A

2017-01-01

As flood risks grow worldwide, a well-designed insurance program engaging various stakeholders becomes a vital instrument in flood risk management. The main challenge concerns the applicability of standard approaches for calculating insurance premiums of rare catastrophic losses. This article focuses on the design of a flood-loss-sharing program involving private insurance based on location-specific exposures. The analysis is guided by a developed integrated catastrophe risk management (ICRM) model consisting of a GIS-based flood model and a stochastic optimization procedure with respect to location-specific risk exposures. To achieve the stability and robustness of the program towards floods with various recurrences, the ICRM uses stochastic optimization procedure, which relies on quantile-related risk functions of a systemic insolvency involving overpayments and underpayments of the stakeholders. Two alternative ways of calculating insurance premiums are compared: the robust derived with the ICRM and the traditional average annual loss approach. The applicability of the proposed model is illustrated in a case study of a Rotterdam area outside the main flood protection system in the Netherlands. Our numerical experiments demonstrate essential advantages of the robust premiums, namely, that they: (1) guarantee the program's solvency under all relevant flood scenarios rather than one average event; (2) establish a tradeoff between the security of the program and the welfare of locations; and (3) decrease the need for other risk transfer and risk reduction measures. © 2016 Society for Risk Analysis.

Canadian Health Measures Survey pre-test: design, methods, results.

PubMed

Tremblay, Mark; Langlois, Renée; Bryan, Shirley; Esliger, Dale; Patterson, Julienne

2007-01-01

The Canadian Health Measures Survey (CHMS) pre-test was conducted to provide information about the challenges and costs associated with administering a physical health measures survey in Canada. To achieve the specific objectives of the pre-test, protocols were developed and tested, and methods for household interviewing and clinic testing were designed and revised. The cost, logistics and suitability of using fixed sites for the CHMS were assessed. Although data collection, transfer and storage procedures are complex, the pre-test experience confirmed Statistics Canada's ability to conduct a direct health measures survey and the willingness of Canadians to participate in such a health survey. Many operational and logistical procedures worked well and, with minor modifications, are being employed in the main survey. Fixed sites were problematic, and survey costs were higher than expected.

24 CFR 200.936 - Supplementary specific procedural requirements under HUD building products certification program...

Code of Federal Regulations, 2014 CFR

2014-04-01

... fireplace stoves certified under the HUD Building Products Certification Program shall be designed... and manufacturer series or model number; and (iv) The type of fuel to be used. (2) The certification... Accreditation Program. (2) The administrator shall visit the manufacturer's facility two times a year to assure...

24 CFR 200.936 - Supplementary specific procedural requirements under HUD building products certification program...

Code of Federal Regulations, 2010 CFR

2010-04-01

... fireplace stoves certified under the HUD Building Products Certification Program shall be designed... and manufacturer series or model number; and (iv) The type of fuel to be used. (2) The certification... Accreditation Program. (2) The administrator shall visit the manufacturer's facility two times a year to assure...

24 CFR 200.936 - Supplementary specific procedural requirements under HUD building products certification program...

Code of Federal Regulations, 2012 CFR

2012-04-01

... fireplace stoves certified under the HUD Building Products Certification Program shall be designed... and manufacturer series or model number; and (iv) The type of fuel to be used. (2) The certification... Accreditation Program. (2) The administrator shall visit the manufacturer's facility two times a year to assure...

24 CFR 200.936 - Supplementary specific procedural requirements under HUD building products certification program...

Code of Federal Regulations, 2011 CFR

2011-04-01

... fireplace stoves certified under the HUD Building Products Certification Program shall be designed... and manufacturer series or model number; and (iv) The type of fuel to be used. (2) The certification... Accreditation Program. (2) The administrator shall visit the manufacturer's facility two times a year to assure...

A PLAN FOR AN EMPLOYMENT ORIENTATION PROGRAM FOR RETARDED PUPILS IN PUBLIC SCHOOLS IN NEW JERSEY.

ERIC Educational Resources Information Center

New Jersey State Dept. of Education, Trenton.

THE GENERAL NATURE OF THE EMPLOYMENT ORIENTATION PROGRAM AND THE IMPORTANCE OF SAFEGUARDING THE TRAINEES' EDUCATIONAL OBJECTIVES AND PERSONAL SAFETY ARE PRESENTED. THIS PROGRAM IS DESIGNED SPECIFICALLY FOR MENTALLY RETARDED STUDENTS AND DIFFERS FROM OTHER COOPERATIVE EDUCATION PROGRAMS IN OBJECTIVES AND OPERATIONAL PROCEDURES. OF PRIME IMPORTANCE…

Purchasing for Food Service: Self-Instruction.

ERIC Educational Resources Information Center

Ross, Lynne Nannen

This book is designed to teach accounting procedures and product specifications that are needed by the competent purchaser in order to make optimum purchasing decisions basic to a successful food service operation. It may be used by any level of food service personnel that is involved with any phase of the purchasing process. Preferably, the book…

Behavioral Vision Training for Myopia: Stimulus Specificity of Training Effects.

ERIC Educational Resources Information Center

Leung, Jin-Pang

1988-01-01

The study assessed transfer of visual training for myopia using two different training stimuli and a single subject A-B-C-A design with a male student volunteer. A procedure including stimulus fading and reinforcement (positive verbal feedback) was used to effectively improve performance on both behavioral acuity tests during the training phases…

City Planning Unit: Grade 6.

ERIC Educational Resources Information Center

Dalton, William Edward

Described is a project designed to make government lessons and economics more appealing to sixth-grade students by having them set up and run a model city. General preparation procedures and set-up of the project, specific lesson plans, additional activities, and project evaluation are examined. An actual 3-dimensional model city was set up on…

40 CFR 1042.840 - Application requirements for remanufactured engines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... scheduled maintenance you did. (g) List the specifications of the test fuel to show that it falls within the... as described in the application (including the test procedures, test parameters, and test fuels) to... other basic parameters of the engine's design and emission controls. List the fuel type on which your...

40 CFR 1042.840 - Application requirements for remanufactured engines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... scheduled maintenance you did. (g) List the specifications of the test fuel to show that it falls within the... as described in the application (including the test procedures, test parameters, and test fuels) to... other basic parameters of the engine's design and emission controls. List the fuel type on which your...

40 CFR 1042.840 - Application requirements for remanufactured engines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... scheduled maintenance you did. (g) List the specifications of the test fuel to show that it falls within the... as described in the application (including the test procedures, test parameters, and test fuels) to... other basic parameters of the engine's design and emission controls. List the fuel type on which your...

Developing and Validating a Rapid Small-Scale Column Test Procedure for GAC Selection using Reconstituted Lyophilized NOM

EPA Science Inventory

Cost effective design and operation of Granular Activated Carbon (GAC) facilities requires the selection of GAC that is optimal for a specific site. Rapid small-scale column tests (RSSCTs) are widely used for GAC assessment due to several advantages, including the ability to simu...

In the Curriculum. Health: Mental Agility and Memory; Reading/Language Arts: The Writer/Reader Connection; Science: Stars.

ERIC Educational Resources Information Center

Robinson, Alice A.

2003-01-01

Provides six library media activities that are designed for use with specific curriculum units in health, science, language arts, and social studies. Each activity identifies library media skills and curriculum objectives, grade levels, resources, instructional roles, procedures, evaluation guidelines, and follow-up activities. (AEF)

A Comparative Study of the Roles and Functions of School Principals and Bilingual Program Administrators.

ERIC Educational Resources Information Center

Sanchez,Gilbert; Cali, Alfred J.

This study was designed to compare time allocations to major functions actually performed and idealized by bilingual administrators and principals; to rank specific procedures used in accomplishing these functions; to determine staffing patterns, and program and organizational characteristics; and to isolate personal/professional demographics of…

NHEXAS PHASE I MARYLAND STUDY--STANDARD OPERATING PROCEDURE FOR DUPLICATE SAMPLING (F12)

EPA Science Inventory

This SOP is designed to provide both general and specific guidance for the collection of duplicate samples by Harvard School of Public Health/Emory University for the NHEXAS project. The purpose of the duplicate sampling was to ensure that the value obtained for a sample was ind...

Coding the Composing Process: A Guide for Teachers and Researchers.

ERIC Educational Resources Information Center

Perl, Sondra

Designed for teachers and researchers interested in the study of the composing process, this guide introduces a method of analysis that can be applied to data from a range of different cases. Specifically, the guide offers a simple, direct coding scheme for describing the movements occurring during composing that involves four procedures: teaching…

24 CFR 200.937 - Supplementary specific procedural requirements under HUD building product standards and...

Code of Federal Regulations, 2012 CFR

2012-04-01

... shower receptors and stalls, plastic lavatories, plastic water closet bowls and tanks. 200.937 Section... units, plastic shower receptors and stalls, plastic lavatories, plastic water closet bowls and tanks. (a... plastic water closet bowls and tanks shall be designed, assembled and tested in compliance with the...

24 CFR 200.937 - Supplementary specific procedural requirements under HUD building product standards and...

Code of Federal Regulations, 2014 CFR

2014-04-01

... shower receptors and stalls, plastic lavatories, plastic water closet bowls and tanks. 200.937 Section... units, plastic shower receptors and stalls, plastic lavatories, plastic water closet bowls and tanks. (a... plastic water closet bowls and tanks shall be designed, assembled and tested in compliance with the...

24 CFR 200.937 - Supplementary specific procedural requirements under HUD building product standards and...

Code of Federal Regulations, 2013 CFR

2013-04-01

... shower receptors and stalls, plastic lavatories, plastic water closet bowls and tanks. 200.937 Section... units, plastic shower receptors and stalls, plastic lavatories, plastic water closet bowls and tanks. (a... plastic water closet bowls and tanks shall be designed, assembled and tested in compliance with the...

Network Performance and Coordination in the Health, Education, Telecommunications System. Satellite Technology Demonstration, Technical Report No. 0422.

ERIC Educational Resources Information Center

Braunstein, Jean; Janky, James M.

This paper describes the network coordination for the Health, Education, Telecommunications (HET) system. Specifically, it discusses HET network performance as a function of a specially-developed coordination system which was designed to link terrestrial equipment to satellite operations centers. Because all procedures and equipment developed for…

Setting Professional Goals: Causing Teachers To Want Inservice Education.

ERIC Educational Resources Information Center

Bey, Theresa M.

Since the major intent of inservice education is to enrich and modify the efforts of every teacher, guidelines are essential. One specific goal-setting process designed for any teacher to conduct a self-assessment of teaching and non-teaching responsibilities is the Complete Procedural Review (CPR). This instrument sets forth teachers' duties and…

A Guide to Preparing Educational Specifications for Secondary Industrial Arts Facilities. Monograph No. 1.

ERIC Educational Resources Information Center

Steeb, Ralph V.

The guide describes procedures for designing secondary industrial arts facilities based on careful scrutiny of the educational program which the facilities are intended to serve. It offers a four step general outline for planning such facilities and discusses in detail the following considerations with respect to writing subject area…

77 FR 58383 - Agency Information Collection Activities: Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-20

...) The Kids' Inpatient Database (KID) is the only all-payer inpatient care database for children in the United States. The KID was specifically designed to permit researchers to study a broad range of conditions and procedures related to child health issues. The KID contains a sample of over 3 million...

An Inservice Program for Vocational Teachers of the Disadvantaged. Handbook.

ERIC Educational Resources Information Center

Ehresman, Norman D.; And Others

A product of a research project designed to improve the teaching effectiveness of vocational teachers of disadvantaged students, this handbook includes the specific procedures and materials that can be utilized in an inservice program for vocational teachers of disadvantaged youth. (The final report of this project is contained in a separate…

Frequency-Specific, Binaural Stimulation of Students with Reading and Spelling Difficulties.

ERIC Educational Resources Information Center

Johansen, Kjeld

A study examined the hearing of learning disabled students (such as dyslexics) in an attempt to classify, identify, and design auditory stimulation procedures. Subjects, 40 students from seventh-grade classes and 40 volunteers (ages 9 to 23) with reading and spelling difficulties, were given listening tests. Results indicated that many of the…

A Restoration Design for Least Bell's Vireo Habitat in San Diego County

Treesearch

Kathryn J. Baird; John P. Rieger

1989-01-01

This paper describes the procedure for developing a specific habitat restoration model. Results of a detailed Least Bell's Vireo (Vireo bellii pusillus) habitat study on the Sweetwater River drainage, San Diego County California, generated the baseline vegetative and habitat data used. Mean percent cover, density, abundance, species composition...

Using Behavioral Skills Training and Video Rehearsal to Teach Blackjack Skills

ERIC Educational Resources Information Center

Speelman, Ryan C.; Whiting, Seth W.; Dixon, Mark R.

2015-01-01

A behavioral skills training procedure that consisted of video instructions, video rehearsal, and video testing was used to teach 4 recreational gamblers a specific skill in playing blackjack (sometimes called "card counting"). A multiple baseline design was used to evaluate intervention effects on card-counting accuracy and chips won or…

78 FR 25846 - Special Conditions: Airbus, Model A340-600 Series Airplanes; Lower Deck Crew Rest Compartments

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-03

... significantly delay issuance of the design approval and thus delivery of the affected aircraft. In addition, the... specific portion of the special conditions, explain the reason for any recommended change, and include... compartment configuration that affect crew member emergency egress or any other procedures affecting the...

Developing and Validating a Rapid Small-Scale Column Test Procedure for GAC Selection using Reconstituted Lyophilized NOM - Portland, OR

EPA Science Inventory

Cost effective design and operation of Granular Activated Carbon (GAC) facilities requires the selection of GAC that is optimal for a specific site. Rapid small-scale column tests (RSSCTs) are widely used for GAC assessment due to several advantages, including the ability to simu...

Multimodal therapy of word retrieval disorder due to phonological encoding dysfunction.

PubMed

Weill-Chounlamountry, Agnès; Capelle, Nathalie; Tessier, Catherine; Pradat-Diehl, Pascale

2013-01-01

To determine whether phonological multimodal therapy can improve naming and communication in a patient showing a lexical phonological naming disorder. This study employed oral and written learning tasks, using an error reduction procedure. A single-case design computer-assisted treatment was used with a 52 year-old woman with fluent aphasia consecutive to a cerebral infarction. The cognitive analysis of her word retrieval disorder exhibited a phonological encoding dysfunction. Thus, a phonological procedure was designed addressing the output phonological lexicon using computer analysis of spoken and written words. The effects were tested for trained words, generalization to untrained words, maintenance and specificity. Transfer of improvement to daily life was also assessed. After therapy, the verbal naming of both trained and untrained words was improved at p < 0.001. The improvement was still maintained after 3 months without therapy. This treatment was specific since the word dictation task did not change. Communication in daily life was improved at p < 0.05. This study of a patient with word retrieval disorder due to phonological encoding dysfunction demonstrated the effectiveness of a phonological and multimodal therapeutic treatment.

Review of Musculoskeletal Injuries and Prevention in the Endoscopy Practitioner

PubMed Central

2014-01-01

Practitioners of endoscopy often experience musculoskeletal pain and injury (most often in the back, neck, shoulders, hands, wrists, and thumbs) that are associated with the minute and repetitive strain that is placed on these areas during endoscopic procedures. This review of the current documentation of endoscopy-related pain and injuries among practitioners finds that such problems are widespread and specific in kind as well as strongly correlated with high procedure volume and procedure duration. Research on the nature and impact of cumulative trauma and overuse syndromes in other professions such as dentistry, pianists, production labor, and athletics is brought to bear on the work of the endoscopist. A more thorough understanding of the nature and prevalence of work-related pain and injury sustained by endoscopists should inform further development of ergonomic practices and equipment design. This article reviews current recommendations for ergonomic design in the endoscopy procedure space and finds that reported compliance with those recommendations is quite low. Strategies for the management of the risk of musculoskeletal injuries related to the practice of endoscopy include compliance with currently recommended ergonomic practices, education of trainees in ergonomic technique when practicing endoscopy, and research toward the modification and development of more ergonomic endoscopes and procedure spaces. PMID:24798940

Cephalopod biology and care, a COST FA1301 (CephsInAction) training school: anaesthesia and scientific procedures.

PubMed

Lopes, Vanessa M; Sampaio, Eduardo; Roumbedakis, Katina; Tanaka, Nobuaki K; Carulla, Lucía; Gambús, Guillermo; Woo, Theodosia; Martins, Catarina P P; Penicaud, Virginie; Gibbings, Colette; Eberle, Jessica; Tedesco, Perla; Fernández, Isabel; Rodríguez-González, Tania; Imperadore, Pamela; Ponte, Giovanna; Fiorito, Graziano

2017-09-01

Cephalopods are the sole invertebrates included in the list of regulated species following the Directive 2010/63/EU. According to the Directive, achieving competence through adequate training is a requisite for people having a role in the different functions (article 23) as such carrying out procedures on animals, designing procedures and projects, taking care of animals, killing animals. Cephalopod Biology and Care Training Program is specifically designed to comply with the requirements of the "working document on the development of a common education and training framework to fulfil the requirements under the Directive 2010/63/EU". The training event occurred at the ICM-CSIC in Barcelona (Spain) where people coming from Europe, America and Asia were instructed on how to cope with regulations for the use of cephalopod molluscs for scientific purposes. The training encompasses discussion on the guidelines for the use and care of animals and their welfare with particular reference to procedures that may be of interest for neuroscience. Intensive discussion has been carried out during the training sessions with focus on behavioural studies and paradigms, welfare assessment, levels of severity of scientific procedures, animal care, handling, transport, individual identification and marking, substance administration, anaesthesia, analgesia and humane killing.

Creep and Creep-Fatigue Crack Growth at Structural Discontinuities and Welds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dr. F. W. Brust; Dr. G. M. Wilkowski; Dr. P. Krishnaswamy

2010-01-27

The subsection ASME NH high temperature design procedure does not admit crack-like defects into the structural components. The US NRC identified the lack of treatment of crack growth within NH as a limitation of the code and thus this effort was undertaken. This effort is broken into two parts. Part 1, summarized here, involved examining all high temperature creep-fatigue crack growth codes being used today and from these, the task objective was to choose a methodology that is appropriate for possible implementation within NH. The second part of this task, which has just started, is to develop design rules formore » possible implementation within NH. This second part is a challenge since all codes require step-by-step analysis procedures to be undertaken in order to assess the crack growth and life of the component. Simple rules for design do not exist in any code at present. The codes examined in this effort included R5, RCC-MR (A16), BS 7910, API 579, and ATK (and some lesser known codes). There are several reasons that the capability for assessing cracks in high temperature nuclear components is desirable. These include: (1) Some components that are part of GEN IV reactors may have geometries that have sharp corners - which are essentially cracks. Design of these components within the traditional ASME NH procedure is quite challenging. It is natural to ensure adequate life design by modeling these features as cracks within a creep-fatigue crack growth procedure. (2) Workmanship flaws in welds sometimes occur and are accepted in some ASME code sections. It can be convenient to consider these as flaws when making a design life assessment. (3) Non-destructive Evaluation (NDE) and inspection methods after fabrication are limited in the size of the crack or flaw that can be detected. It is often convenient to perform a life assessment using a flaw of a size that represents the maximum size that can elude detection. (4) Flaws that are observed using in-service detection methods often need to be addressed as plants age. Shutdown inspection intervals can only be designed using creep and creep-fatigue crack growth techniques. (5) The use of crack growth procedures can aid in examining the seriousness of creep damage in structural components. How cracks grow can be used to assess margins on components and lead to further safe operation. After examining the pros and cons of all these methods, the R5 code was chosen as the most up-to-date and validated high temperature creep and creep fatigue code currently used in the world at present. R5 is considered the leader because the code: (1) has well established and validated rules, (2) has a team of experts continually improving and updating it, (3) has software that can be used by designers, (4) extensive validation in many parts with available data from BE resources as well as input from Imperial college's database, and (5) was specifically developed for use in nuclear plants. R5 was specifically developed for use in gas cooled nuclear reactors which operate in the UK and much of the experience is based on materials and temperatures which are experienced in these reactors. If the next generation advanced reactors to be built in the US used these same materials within the same temperature ranges as these reactors, then R5 may be appropriate for consideration of direct implementation within ASME code NH or Section XI. However, until more verification and validation of these creep/fatigue crack growth rules for the specific materials and temperatures to be used in the GEN IV reactors is complete, ASME should consider delaying this implementation. With this in mind, it is this authors opinion that R5 methods are the best available for code use today. The focus of this work was to examine the literature for creep and creep-fatigue crack growth procedures that are well established in codes in other countries and choose a procedure to consider implementation into ASME NH. It is very important to recognize that all creep and creep fatigue crack growth procedures that are part of high temperature design codes are related and very similar. This effort made no attempt to develop a new creep-fatigue crack growth predictive methodology. Rather examination of current procedures was the only goal. The uncertainties in the R5 crack growth methods and recommendations for more work are summarized here also.« less

Optimization of a magnetic capture RT-LAMP assay for fast and real-time detection of potato virus Y and differentiation of N and O serotypes.

PubMed

Treder, Krzysztof; Chołuj, Joanna; Zacharzewska, Bogumiła; Babujee, Lavanya; Mielczarek, Mateusz; Burzyński, Adam; Rakotondrafara, Aurélie M

2018-02-01

Potato virus Y (PVY) infection has been a global challenge for potato production and the leading cause of downgrading and rejection of seed crops for certification. Accurate and timely diagnosis is a key for effective disease control. Here, we have optimized a reverse transcription loop-mediated amplification (RT-LAMP) assay to differentiate the PVY O and N serotypes. The RT-LAMP assay is based on isothermal autocyclic strand displacement during DNA synthesis. The high specificity of this method relies heavily on the primer sets designed for the amplification of the targeted regions. We designed specific primer sets targeting a region within the coat protein gene that contains nucleotide signatures typical for O and N coat protein types, and these primers differ in their annealing temperature. Combining this assay with total RNA extraction by magnetic capture, we have established a highly sensitive, simplified and shortened RT-LAMP procedure as an alternative to conventional nucleic acid assays for diagnosis. This optimized procedure for virus detection may be used as a preliminary test for identifying the viral serotype prior to investing time and effort in multiplex RT-PCR tests when a specific strain is needed.

A haptic device for guide wire in interventional radiology procedures.

PubMed

Moix, Thomas; Ilic, Dejan; Bleuler, Hannes; Zoethout, Jurjen

2006-01-01

Interventional Radiology (IR) is a minimally invasive procedure where thin tubular instruments, guide wires and catheters, are steered through the patient's vascular system under X-ray imaging. In order to perform these procedures, a radiologist has to be trained to master hand-eye coordination, instrument manipulation and procedure protocols. The existing simulation systems all have major drawbacks: the use of modified instruments, unrealistic insertion lengths, high inertia of the haptic device that creates a noticeably degraded dynamic behavior or excessive friction that is not properly compensated for. In this paper we propose a quality training environment dedicated to IR. The system is composed of a virtual reality (VR) simulation of the patient's anatomy linked to a robotic interface providing haptic force feedback. This paper focuses on the requirements, design and prototyping of a specific haptic interface for guide wires.

Procedural Guide for International Gauging Stations on Boundary Waters Between Canada and the United States of America

USGS Publications Warehouse

Huberman, S.; Slater, James; Condes, A.

1985-01-01

INTRODUCTION Since 1909, the United States of America (U.S.A.) and Canada have employed a system of monitoring stream-flow and water levels for shared waters based upon professionalism, trust and goodwill. This document has been prepared in considerable detail for use by managers and field officers at all levels of government in Canada and the United States. Its purpose is to serve as a guide in attaining uniform procedures in the designation and operation of International Gauging Stations. For special situations where these procedures do not apply, specific mention is made in appropriate sections of the guide. This guide supersedes that of November 4, 1969, and the guide entitled 'The Procedural Guide for Operation of International Gauging Stations, St. Mary- Milk Rivers,' dated March 12, 1979.

Soil drying procedure affects the DNA quantification of Lactarius vinosus but does not change the fungal community composition.

PubMed

Castaño, Carles; Parladé, Javier; Pera, Joan; Martínez de Aragón, Juan; Alday, Josu G; Bonet, José Antonio

2016-11-01

Drying soil samples before DNA extraction is commonly used for specific fungal DNA quantification and metabarcoding studies, but the impact of different drying procedures on both the specific fungal DNA quantity and the fungal community composition has not been analyzed. We tested three different drying procedures (freeze-drying, oven-drying, and room temperature) on 12 different soil samples to determine (a) the soil mycelium biomass of the ectomycorrhizal species Lactarius vinosus using qPCR with a specifically designed TaqMan® probe and (b) the fungal community composition and diversity using the PacBio® RS II sequencing platform. Mycelium biomass of L. vinosus was significantly greater in the freeze-dried soil samples than in samples dried at oven and room temperature. However, drying procedures had no effect on fungal community composition or on fungal diversity. In addition, there were no significant differences in the proportions of fungi according to their functional roles (moulds vs. mycorrhizal species) in response to drying procedures. Only six out of 1139 operational taxonomic units (OTUs) had increased their relative proportions after soil drying at room temperature, with five of these OTUs classified as mould or yeast species. However, the magnitude of these changes was small, with an overall increase in relative abundance of these OTUs of approximately 2 %. These results suggest that DNA degradation may occur especially after drying soil samples at room temperature, but affecting equally nearly all fungi and therefore causing no significant differences in diversity and community composition. Despite the minimal effects caused by the drying procedures at the fungal community composition, freeze-drying resulted in higher concentrations of L. vinosus DNA and prevented potential colonization from opportunistic species.

WIPP waste characterization program sampling and analysis guidance manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-01-01

The Waste Isolation Pilot Plant (WIPP) Waste Characterization Program Sampling and Analysis Guidance Manual (Guidance Manual) provides a unified source of information on the sampling and analytical techniques that enable Department of Energy (DOE) facilities to comply with the requirements established in the current revision of the Quality Assurance Program Plan (QAPP) for the WIPP Experimental-Waste Characterization Program (the Program). This Guidance Manual includes all of the sampling and testing methodologies accepted by the WIPP Project Office (DOE/WPO) for use in implementing the Program requirements specified in the QAPP. This includes methods for characterizing representative samples of transuranic (TRU) wastesmore » at DOE generator sites with respect to the gas generation controlling variables defined in the WIPP bin-scale and alcove test plans, as well as waste container headspace gas sampling and analytical procedures to support waste characterization requirements under the WIPP test program and the Resource Conservation and Recovery Act (RCRA). The procedures in this Guidance Manual are comprehensive and detailed and are designed to provide the necessary guidance for the preparation of site specific procedures. The use of these procedures is intended to provide the necessary sensitivity, specificity, precision, and comparability of analyses and test results. The solutions to achieving specific program objectives will depend upon facility constraints, compliance with DOE Orders and DOE facilities' operating contractor requirements, and the knowledge and experience of the TRU waste handlers and analysts. With some analytical methods, such as gas chromatography/mass spectrometry, the Guidance Manual procedures may be used directly. With other methods, such as nondestructive/destructive characterization, the Guidance Manual provides guidance rather than a step-by-step procedure.« less

An Intelligent Automation Platform for Rapid Bioprocess Design.

PubMed

Wu, Tianyi; Zhou, Yuhong

2014-08-01

Bioprocess development is very labor intensive, requiring many experiments to characterize each unit operation in the process sequence to achieve product safety and process efficiency. Recent advances in microscale biochemical engineering have led to automated experimentation. A process design workflow is implemented sequentially in which (1) a liquid-handling system performs high-throughput wet lab experiments, (2) standalone analysis devices detect the data, and (3) specific software is used for data analysis and experiment design given the user's inputs. We report an intelligent automation platform that integrates these three activities to enhance the efficiency of such a workflow. A multiagent intelligent architecture has been developed incorporating agent communication to perform the tasks automatically. The key contribution of this work is the automation of data analysis and experiment design and also the ability to generate scripts to run the experiments automatically, allowing the elimination of human involvement. A first-generation prototype has been established and demonstrated through lysozyme precipitation process design. All procedures in the case study have been fully automated through an intelligent automation platform. The realization of automated data analysis and experiment design, and automated script programming for experimental procedures has the potential to increase lab productivity. © 2013 Society for Laboratory Automation and Screening.

An Intelligent Automation Platform for Rapid Bioprocess Design

PubMed Central

Wu, Tianyi

2014-01-01

Bioprocess development is very labor intensive, requiring many experiments to characterize each unit operation in the process sequence to achieve product safety and process efficiency. Recent advances in microscale biochemical engineering have led to automated experimentation. A process design workflow is implemented sequentially in which (1) a liquid-handling system performs high-throughput wet lab experiments, (2) standalone analysis devices detect the data, and (3) specific software is used for data analysis and experiment design given the user’s inputs. We report an intelligent automation platform that integrates these three activities to enhance the efficiency of such a workflow. A multiagent intelligent architecture has been developed incorporating agent communication to perform the tasks automatically. The key contribution of this work is the automation of data analysis and experiment design and also the ability to generate scripts to run the experiments automatically, allowing the elimination of human involvement. A first-generation prototype has been established and demonstrated through lysozyme precipitation process design. All procedures in the case study have been fully automated through an intelligent automation platform. The realization of automated data analysis and experiment design, and automated script programming for experimental procedures has the potential to increase lab productivity. PMID:24088579

Design enhancement tools in MSC/NASTRAN

NASA Technical Reports Server (NTRS)

Wallerstein, D. V.

1984-01-01

Design sensitivity is the calculation of derivatives of constraint functions with respect to design variables. While a knowledge of these derivatives is useful in its own right, the derivatives are required in many efficient optimization methods. Constraint derivatives are also required in some reanalysis methods. It is shown where the sensitivity coefficients fit into the scheme of a basic organization of an optimization procedure. The analyzer is to be taken as MSC/NASTRAN. The terminator program monitors the termination criteria and ends the optimization procedure when the criteria are satisfied. This program can reside in several plances: in the optimizer itself, in a user written code, or as part of the MSC/EOS (Engineering Operating System) MSC/EOS currently under development. Since several excellent optimization codes exist and since they require such very specialized technical knowledge, the optimizer under the new MSC/EOS is considered to be selected and supplied by the user to meet his specific needs and preferences. The one exception to this is a fully stressed design (FSD) based on simple scaling. The gradients are currently supplied by various design sensitivity options now existing in MSC/NASTRAN's design sensitivity analysis (DSA).

Detection of pork adulteration in processed meat by species-specific PCR-QIAxcel procedure based on D-loop and cytb genes.

PubMed

Barakat, Hassan; El-Garhy, Hoda A S; Moustafa, Mahmoud M A

2014-12-01

Detection of pork meat adulteration in "halal" meat products is a crucial issue in the fields of modern food inspection according to implementation of very strict procedures for halal food labelling. Present study aims at detecting and quantifying pork adulteration in both raw and cooked manufactured sausages. This is by applying an optimized species-specific PCR procedure followed by QIAxcel capillary electrophoresis system. Manufacturing experiment was designed by incorporating pork with beef meat at 0.01 to 10 % substitution levels beside beef and pork sausages as negative and positive controls, respectively. Subsequently, sausages were divided into raw and cooked sausages then subjected to DNA extraction. Results indicated that PCR amplifications of mitochondrial D-loop and cytochrome b (cytb) genes by porcine-specific primers produced 185 and 117 bp pork-specific DNA fragments in sausages, respectively. No DNA fragments were detected when PCR was applied on beef sausage DNA confirming primers specificity. For internal control, a 141-bp DNA fragment of eukaryotic 18S ribosomal RNA (rRNA) gene was amplified from pork and beef DNA templates. Although PCR followed by either QIAxcel or agarose techniques were efficient for targeted DNA fragments differentiation even as low as 0.01 % (pork/meat: w/w). For proficiency, adequacy, and performance, PCR-QIA procedure is highly sensitive, a time-saver, electronically documented, mutagenic-reagent free, of little manual errors, accurate in measuring PCR fragments length, and quantitative data supplier. In conclusion, it can be suggested that optimized PCR-QAI is considered as a rapid and sensitive method for routine pork detection and quantification in raw or processed meat.

Comparison of study designs for acute otitis media trials.

PubMed

Pichichero, Michael E; Casey, Janet R

2008-06-01

A framework for evaluating the efficacy of antibiotics in development as well as those currently approved for acute otitis media (AOM) is needed. Review strengths and limitations of various antibiotic trial designs and their outcome measures. A review of 157 published trials involving 36,710 subjects for the treatment of AOM. AOM trials have three designs: (1) clinical, clinical diagnosis and assessment of outcomes; (2) single tympanocentesis, microbiologic diagnosis (by middle ear fluid culture) and clinical assessment of outcomes; and (3) double tympanocentesis, microbiologic diagnosis and microbiologic outcome assessment. Identifiable strengths and limitations of each design are reviewed. Case definitions for entry of children in trials of AOM vary widely. The lack of stringent diagnostic criteria in a clinical design allows for inclusion of a significant proportion of children with a non-bacterial etiology (i.e., viral AOM or otitis media with effusion). Tympanocentesis increases diagnostic accuracy at study entry; however, the procedure is confounding because of its potentially therapeutic benefit and the procedure is not performed in a uniform manner. A second tympanocentesis allows a high sensitivity to detect microbiologic eradication, but it does not correlate with clinical outcomes in half of the cases. The timing of outcome assessment also varies widely among trials. Improved clinical diagnosis criteria for AOM are needed to enhance specificity; emphasis on a bulging tympanic membrane has the best evidence base. Tympanocentesis within study designs has merits. At study entry it assures diagnostic accuracy but may alter outcomes and it is useful to document microbiologic outcomes but lacks specificity for clinical outcomes. For all designs, test of cure assessment 2-7 days after completion of therapy seems most appropriate.

Manufacturing Methods and Technology (MM&T) program. 10.6 micrometer carbon dioxide TEA (Transverely Excited Atmospheric) lasers

NASA Astrophysics Data System (ADS)

Luck, C. F.

1983-06-01

This report documents the efforts of Raytheon Company to conduct a manufacturing methods and technology (MM&T) program for 10.6 micrometer carbon dioxide TEA lasers. A set of laser parameters is given and a conforming tube design is described. Results of thermal and mechanical stress analyses are detailed along with a procedure for assembling and testing the laser tube. Also provided are purchase specifications for optics and process specifications for some of the essential operations.

High-Fidelity Roadway Modeling and Simulation

NASA Technical Reports Server (NTRS)

Wang, Jie; Papelis, Yiannis; Shen, Yuzhong; Unal, Ozhan; Cetin, Mecit

2010-01-01

Roads are an essential feature in our daily lives. With the advances in computing technologies, 2D and 3D road models are employed in many applications, such as computer games and virtual environments. Traditional road models were generated by professional artists manually using modeling software tools such as Maya and 3ds Max. This approach requires both highly specialized and sophisticated skills and massive manual labor. Automatic road generation based on procedural modeling can create road models using specially designed computer algorithms or procedures, reducing the tedious manual editing needed for road modeling dramatically. But most existing procedural modeling methods for road generation put emphasis on the visual effects of the generated roads, not the geometrical and architectural fidelity. This limitation seriously restricts the applicability of the generated road models. To address this problem, this paper proposes a high-fidelity roadway generation method that takes into account road design principles practiced by civil engineering professionals, and as a result, the generated roads can support not only general applications such as games and simulations in which roads are used as 3D assets, but also demanding civil engineering applications, which requires accurate geometrical models of roads. The inputs to the proposed method include road specifications, civil engineering road design rules, terrain information, and surrounding environment. Then the proposed method generates in real time 3D roads that have both high visual and geometrical fidelities. This paper discusses in details the procedures that convert 2D roads specified in shape files into 3D roads and civil engineering road design principles. The proposed method can be used in many applications that have stringent requirements on high precision 3D models, such as driving simulations and road design prototyping. Preliminary results demonstrate the effectiveness of the proposed method.

Latch fittings for the scientific instruments on the space telescope

NASA Technical Reports Server (NTRS)

Dozier, J. D.; Kaelber, E.

1983-01-01

Latch fittings which kinematically mount the replaceable scientific instruments onto the Space Telescope must maintain precise alignment and thermal stability for on-orbit observations. Design features which are needed to meet stringent criteria include the use of ceramic isolators for thermal and electrical insulation, materials with different coefficients of thermal expansion for athermalization, precision manufacturing procedures, and extremely tight tolerances. A specific latch fitting to be discussed is a ball-and-socket design. In addition, testing, crew aids, and problems will be covered.

Membrane Filter Technique for Enumeration of Enterococci in Marine Waters

PubMed Central

Levin, M. A.; Fischer, J. R.; Cabelli, V. J.

1975-01-01

A membrane filter procedure is described for the enumeration of enterococci in marine waters. The procedure utilizes a highly selective and somewhat differential primary isolation medium followed by an in situ substrate test for identifying colonies of those organisms capable of hydrolyzing esculin. The procedure (mE) was evaluated with known streptococci strains and field samples with regard to its accuracy, sensitivity, selectivity, specificity, precision, and comparability to existing methods. Essentially quantitative recovery was obtained with seawater-stressed cells of Streptococcus faecalis and S. faccium. Neither S. bovis, S. equinus, S. mitis, nor S. salivarius grew on the medium. The selectivity of the medium was such that a 10,000-fold reduction in background organisms was obtained relative to a medium which contained no inhibitors and was incubated at 35 C. About 90% of those typical colonies designated as enterococci confirmed as such and about 12% of the colonies not so designated were, in fact, identified as enterococci. Plate to plate variability across samples approximated that expected by chance alone. Verified recoveries of enterococci from natural samples by the mE procedure, on the average, exceeded those by the KF method by one order of magnitude. PMID:807165

Identification of potential neuromotor mechanisms of manual therapy in patients with musculoskeletal disablement: rationale and description of a clinical trial

PubMed Central

Fisher, Beth E; Davenport, Todd E; Kulig, Kornelia; Wu, Allan D

2009-01-01

Background Many health care practitioners use a variety of hands-on treatments to improve symptoms and disablement in patients with musculoskeletal pathology. Research to date indirectly suggests a potentially broad effect of manual therapy on the neuromotor processing of functional behavior within the supraspinal central nervous system (CNS) in a manner that may be independent of modification at the level of local spinal circuits. However, the effect of treatment speed, as well as the specific mechanism and locus of CNS changes, remain unclear. Methods/Design We developed a placebo-controlled, randomized study to test the hypothesis that manual therapy procedures directed to the talocrural joint in individuals with post-acute ankle sprain induce a change in corticospinal excitability that is relevant to improve the performance of lower extremity functional behavior. Discussion This study is designed to identify potential neuromotor changes associated with manual therapy procedures directed to the appendicular skeleton, compare the relative effect of treatment speed on potential neuromotor effects of manual therapy procedures, and determine the behavioral relevance of potential neuromotor effects of manual therapy procedures. Trial Registration identifier NCT00847769. PMID:19460169

Chance of Vulnerability Reduction in Application-Specific NoC through Distance Aware Mapping Algorithm

NASA Astrophysics Data System (ADS)

Janidarmian, Majid; Fekr, Atena Roshan; Bokharaei, Vahhab Samadi

2011-08-01

Mapping algorithm which means which core should be linked to which router is one of the key issues in the design flow of network-on-chip. To achieve an application-specific NoC design procedure that minimizes the communication cost and improves the fault tolerant property, first a heuristic mapping algorithm that produces a set of different mappings in a reasonable time is presented. This algorithm allows the designers to identify the set of most promising solutions in a large design space, which has low communication costs while yielding optimum communication costs in some cases. Another evaluated parameter, vulnerability index, is then considered as a principle of estimating the fault-tolerance property in all produced mappings. Finally, in order to yield a mapping which considers trade-offs between these two parameters, a linear function is defined and introduced. It is also observed that more flexibility to prioritize solutions within the design space is possible by adjusting a set of if-then rules in fuzzy logic.

Design and test of aircraft engine isolators for reduced interior noise

NASA Technical Reports Server (NTRS)

Unruh, J. F.; Scheidt, D. C.

1982-01-01

Improved engine vibration isolation was proposed to be the most weight and cost efficient retrofit structure-borne noise control measure for single engine general aviation aircraft. A study was carried out the objectives: (1) to develop an engine isolator design specification for reduced interior noise transmission, (2) select/design candidate isolators to meet a 15 dB noise reduction design goal, and (3) carry out a proof of concept evaluation test. Analytical model of the engine, vibration isolators and engine mount structure were coupled to an empirical model of the fuselage for noise transmission evaluation. The model was used to develop engine isolator dynamic properties design specification for reduced noise transmission. Candidate isolators ere chosen from available product literature and retrofit to a test aircraft. A laboratory based test procedure was then developed to simulate engine induced noise transmission in the aircraft for a proof of concept evaluation test. Three candidate isolator configurations were evaluated for reduced structure-borne noise transmission relative to the original equipment isolators.

Umbilical Connect Techniques Improvement-Technology Study

NASA Technical Reports Server (NTRS)

Valkema, Donald C.

1972-01-01

The objective of this study was to develop concepts, specifications, designs, techniques, and procedures capable of significantly reducing the time required to connect and verify umbilicals for ground services to the space shuttle. The desired goal was to reduce the current time requirement of several shifts for the Saturn 5/Apollo to an elapsed time of less than one hour to connect and verify all of the space shuttle ground service umbilicals. The study was conducted in four phases: (1) literature and hardware examination, (2) concept development, (3) concept evaluation and tradeoff analysis, and (4) selected concept design. The final product of this study was a detail design of a rise-off disconnect panel prototype test specimen for a LO2/LH2 booster (or an external oxygen/hydrogen tank for an orbiter), a detail design of a swing-arm mounted preflight umbilical carrier prototype test specimen, and a part 1 specification for the umbilical connect and verification design for the vehicles as defined in the space shuttle program.

Design of 3-D Printed Concentric Tube Robots.

PubMed

Morimoto, Tania K; Okamura, Allison M

2016-12-01

Concentric tube surgical robots are minimally invasive devices with the advantages of snake-like reconfigurability, long and thin form factor, and placement of actuation outside the patient's body. These robots can also be designed and manufactured to acquire targets in specific patients for treating specific diseases in a manner that minimizes invasiveness. We propose that concentric tube robots can be manufactured using 3-D printing technology on a patient- and procedure-specific basis. In this paper, we define the design requirements and manufacturing constraints for 3-D printed concentric tube robots and experimentally demonstrate the capabilities of these robots. While numerous 3-D printing technologies and materials can be used to create such robots, one successful example uses selective laser sintering to make an outer tube with a polyether block amide and uses stereolithography to make an inner tube with a polypropylene-like material. This enables a tube pair with precurvatures of 0.0775 and 0.0455 mm -1 , which can withstand strains of 20% and 5.5% for the outer and inner tubes, respectively.

Automating software design system DESTA

NASA Technical Reports Server (NTRS)

Lovitsky, Vladimir A.; Pearce, Patricia D.

1992-01-01

'DESTA' is the acronym for the Dialogue Evolutionary Synthesizer of Turnkey Algorithms by means of a natural language (Russian or English) functional specification of algorithms or software being developed. DESTA represents the computer-aided and/or automatic artificial intelligence 'forgiving' system which provides users with software tools support for algorithm and/or structured program development. The DESTA system is intended to provide support for the higher levels and earlier stages of engineering design of software in contrast to conventional Computer Aided Design (CAD) systems which provide low level tools for use at a stage when the major planning and structuring decisions have already been taken. DESTA is a knowledge-intensive system. The main features of the knowledge are procedures, functions, modules, operating system commands, batch files, their natural language specifications, and their interlinks. The specific domain for the DESTA system is a high level programming language like Turbo Pascal 6.0. The DESTA system is operational and runs on an IBM PC computer.

A SAS(®) macro implementation of a multiple comparison post hoc test for a Kruskal-Wallis analysis.

PubMed

Elliott, Alan C; Hynan, Linda S

2011-04-01

The Kruskal-Wallis (KW) nonparametric analysis of variance is often used instead of a standard one-way ANOVA when data are from a suspected non-normal population. The KW omnibus procedure tests for some differences between groups, but provides no specific post hoc pair wise comparisons. This paper provides a SAS(®) macro implementation of a multiple comparison test based on significant Kruskal-Wallis results from the SAS NPAR1WAY procedure. The implementation is designed for up to 20 groups at a user-specified alpha significance level. A Monte-Carlo simulation compared this nonparametric procedure to commonly used parametric multiple comparison tests. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Development and Evaluation of a Multiplex Real-Time Polymerase Chain Reaction Procedure to Clinically Type Prevalent Salmonella enterica Serovars

PubMed Central

Muñoz, Nélida; Diaz-Osorio, Miguel; Moreno, Jaime; Sánchez-Jiménez, Miryan; Cardona-Castro, Nora

2010-01-01

A multiplex real-time polymerase chain reaction procedure was developed to identify the most prevalent clinical isolates of Salmonella enterica subsp. enterica. Genes from the rfb, fliC, fljB, and viaB groups that encode the O, H, and Vi antigens were used to design 15 primer pairs and TaqMan probes specific for the genes rfbJ, wzx, fliC, fljB, wcdB, the sdf-l sequence, and invA, which was used as an internal amplification control. The primers and probes were variously combined into six sets. The first round of reactions used two of these sets to detect Salmonella O:4, O:9, O:7, O:8, and O:3,10 serogroups. Once the serogroups were identified, the results of a second round of reactions that used primers and probes for the flagellar antigen l genes, 1,2; e,h; g,m; d; e,n,x; and z10, and the Vi gene were used to identify individual serovars. The procedure was standardized using 18 Salmonella reference strains and other enterobacteria. The procedure's reliability and sensitivity was evaluated using 267 randomly chosen serotyped Salmonella clinical isolates. The procedure had a sensitivity of 95.5% and was 100% specific. Thus, our technique is a quick, sensitive, reliable, and specific means of identifying S. enterica serovars and can be used in conjunction with traditional serotyping. Other primer and probe combinations could be used to increase the number of identifiable serovars. PMID:20110454

Putting 3D modelling and 3D printing into practice: virtual surgery and preoperative planning to reconstruct complex post-traumatic skeletal deformities and defects

PubMed Central

Tetsworth, Kevin; Block, Steve; Glatt, Vaida

2017-01-01

3D printing technology has revolutionized and gradually transformed manufacturing across a broad spectrum of industries, including healthcare. Nowhere is this more apparent than in orthopaedics with many surgeons already incorporating aspects of 3D modelling and virtual procedures into their routine clinical practice. As a more extreme application, patient-specific 3D printed titanium truss cages represent a novel approach for managing the challenge of segmental bone defects. This review illustrates the potential indications of this innovative technique using 3D printed titanium truss cages in conjunction with the Masquelet technique. These implants are custom designed during a virtual surgical planning session with the combined input of an orthopaedic surgeon, an orthopaedic engineering professional and a biomedical design engineer. The ability to 3D model an identical replica of the original intact bone in a virtual procedure is of vital importance when attempting to precisely reconstruct normal anatomy during the actual procedure. Additionally, other important factors must be considered during the planning procedure, such as the three-dimensional configuration of the implant. Meticulous design is necessary to allow for successful implantation through the planned surgical exposure, while being aware of the constraints imposed by local anatomy and prior implants. This review will attempt to synthesize the current state of the art as well as discuss our personal experience using this promising technique. It will address implant design considerations including the mechanical, anatomical and functional aspects unique to each case. PMID:28220752

Putting 3D modelling and 3D printing into practice: virtual surgery and preoperative planning to reconstruct complex post-traumatic skeletal deformities and defects.

PubMed

Tetsworth, Kevin; Block, Steve; Glatt, Vaida

2017-01-01

3D printing technology has revolutionized and gradually transformed manufacturing across a broad spectrum of industries, including healthcare. Nowhere is this more apparent than in orthopaedics with many surgeons already incorporating aspects of 3D modelling and virtual procedures into their routine clinical practice. As a more extreme application, patient-specific 3D printed titanium truss cages represent a novel approach for managing the challenge of segmental bone defects. This review illustrates the potential indications of this innovative technique using 3D printed titanium truss cages in conjunction with the Masquelet technique. These implants are custom designed during a virtual surgical planning session with the combined input of an orthopaedic surgeon, an orthopaedic engineering professional and a biomedical design engineer. The ability to 3D model an identical replica of the original intact bone in a virtual procedure is of vital importance when attempting to precisely reconstruct normal anatomy during the actual procedure. Additionally, other important factors must be considered during the planning procedure, such as the three-dimensional configuration of the implant. Meticulous design is necessary to allow for successful implantation through the planned surgical exposure, while being aware of the constraints imposed by local anatomy and prior implants. This review will attempt to synthesize the current state of the art as well as discuss our personal experience using this promising technique. It will address implant design considerations including the mechanical, anatomical and functional aspects unique to each case. © The Authors, published by EDP Sciences, 2017.

Communications processor for C3 analysis and wargaming

NASA Astrophysics Data System (ADS)

Clark, L. N.; Pless, L. D.; Rapp, R. L.

1982-03-01

This thesis developed the software capability to allow the investigation of c3 problems, procedures and methodologies. The resultant communications model, that while independent of a specific wargame, is currently implemented in conjunction with the McClintic Theater Model. It provides a computerized message handling system (C3 Model) which allows simulation of communication links (circuits) with user-definable delays; garble and loss rates; and multiple circuit types, addresses, and levels of command. It is designed to be used for test and evaluation of command and control problems in the areas of organizational relationships, communication networks and procedures, and combat doctrine or tactics.

Engineering applications of strong ground motion simulation

NASA Astrophysics Data System (ADS)

Somerville, Paul

1993-02-01

The formulation, validation and application of a procedure for simulating strong ground motions for use in engineering practice are described. The procedure uses empirical source functions (derived from near-source strong motion recordings of small earthquakes) to provide a realistic representation of effects such as source radiation that are difficult to model at high frequencies due to their partly stochastic behavior. Wave propagation effects are modeled using simplified Green's functions that are designed to transfer empirical source functions from their recording sites to those required for use in simulations at a specific site. The procedure has been validated against strong motion recordings of both crustal and subduction earthquakes. For the validation process we choose earthquakes whose source models (including a spatially heterogeneous distribution of the slip of the fault) are independently known and which have abundant strong motion recordings. A quantitative measurement of the fit between the simulated and recorded motion in this validation process is used to estimate the modeling and random uncertainty associated with the simulation procedure. This modeling and random uncertainty is one part of the overall uncertainty in estimates of ground motions of future earthquakes at a specific site derived using the simulation procedure. The other contribution to uncertainty is that due to uncertainty in the source parameters of future earthquakes that affect the site, which is estimated from a suite of simulations generated by varying the source parameters over their ranges of uncertainty. In this paper, we describe the validation of the simulation procedure for crustal earthquakes against strong motion recordings of the 1989 Loma Prieta, California, earthquake, and for subduction earthquakes against the 1985 Michoacán, Mexico, and Valparaiso, Chile, earthquakes. We then show examples of the application of the simulation procedure to the estimatation of the design response spectra for crustal earthquakes at a power plant site in California and for subduction earthquakes in the Seattle-Portland region. We also demonstrate the use of simulation methods for modeling the attenuation of strong ground motion, and show evidence of the effect of critical reflections from the lower crust in causing the observed flattening of the attenuation of strong ground motion from the 1988 Saguenay, Quebec, and 1989 Loma Prieta earthquakes.

75 FR 64737 - Automated Commercial Environment (ACE): Announcement of a National Customs Automation Program...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-20

... Commissioner of CBP with authority to conduct limited test programs or procedures designed to evaluate planned.... Specifically, CBP is looking for test participants to include: 2-3 Ocean Carriers. At least one must be filing... their software ready to test with CBP once CBP begins the certification process. CBP will post the...

Contextual Specificity of Extinction of Delay but Not Trace Eyeblink Conditioning in Humans

ERIC Educational Resources Information Center

Grillon, Christian; Alvarez, Ruben P.; Johnson, Linda; Chavis, Chanen

2008-01-01

Renewal of an extinguished conditioned response has been demonstrated in humans and in animals using various types of procedures, except renewal of motor learning such as eyeblink conditioning. We tested renewal of delay and trace eyeblink conditioning in a virtual environment in an ABA design. Following acquisition in one context (A, e.g., an…

Assessing and Comparing Physical Environments for Nursing Home Residents: Using New Tools for Greater Research Specificity

ERIC Educational Resources Information Center

Cutler, Lois J.; Kane, Rosalie A.; Degenholtz, Howard B.; Miller, Michael J.; Grant, Leslie

2006-01-01

Purpose: We developed and tested theoretically derived procedures to observe physical environments experienced by nursing home residents at three nested levels: their rooms, the nursing unit, and the overall facility. Illustrating with selected descriptive results, in this article we discuss the development of the approach. Design and Methods: On…

Qualification of the flight-critical AFTI/F-16 digital flight control system. [Advanced Fighter Technology Integration

NASA Technical Reports Server (NTRS)

Mackall, D. A.; Ishmael, S. D.; Regenie, V. A.

1983-01-01

Qualification considerations for assuring the safety of a life-critical digital flight control system include four major areas: systems interactions, verification, validation, and configuration control. The AFTI/F-16 design, development, and qualification illustrate these considerations. In this paper, qualification concepts, procedures, and methodologies are discussed and illustrated through specific examples.

An earth anchor system: installation and design guide.

Treesearch

R.L. Copstead; D.D. Studier

1990-01-01

A system for anchoring the guylines and skylines of cable yarding equipment is presented. A description of three types of tipping plate anchors is given. Descriptions of the installation equipment and methods specific to each type are given. Procedures for determining the correct number of anchors to install are included, as are guidelines for installing the anchors so...

Some Direct and Generalized Effects of Replacing an Autistic Man's Echolalia with Correct Responses to Questions.

ERIC Educational Resources Information Center

McMorrow, Martin J.; Foxx, R. M.

1986-01-01

The use of operant procedures was extended to decrease immediate echolalia and increase appropriate responding to questions of a 21-year-old autistic man. Multiple baseline designs demonstrated that echolalia was rapidly replaced with correct stimulus-specific responses. A variety of generalized improvements were observed in verbal responses to…

The Composition of the TV Picture: Suggested Hypotheses to Test the Forces That Operate within the Television Screen.

ERIC Educational Resources Information Center

Metallinos, Nikos

This paper suggests specific experimental designs, criteria measures, and testing procedures for the empirical study of various field forces operative in the structure of the television picture. The purpose of the paper is twofold: first, to illustrate, through selected videotapes, the various field forces and, second, to provide specific…

Looking at the Results. The ACTFL Foreign Language Education Series, Vol. 10.

ERIC Educational Resources Information Center

Omaggio, Alice C.; And Others

This paper attempts to provide a synthesis of the best available knowledge on ways to evaluate the effectiveness of foreiqn language programs. Procedures that have worked well are outlined, an evaluation model is suggested, and a list of specific guidelines, checklists, and other resources is provided. The results of a survey designed to get…

Creating Tic Suppression: Comparing the Effects of Verbal Instruction to Differential Reinforcement

ERIC Educational Resources Information Center

Woods, Douglas W.; Himle, Michael B.

2004-01-01

The purpose of this study was to compare two methods designed to produce tic reduction in 4 children with Tourette's syndrome. Specifically, a verbal instruction not to engage in tics was compared to a verbal instruction plus differential reinforcement of zero-rate behavior (DRO). Results showed that the DRO-enhanced procedure yielded greater…

Cultural Adaptations of the "Strengthening Families Programme 10-14" in the US Pacific Northwest: A Qualitative Evaluation

ERIC Educational Resources Information Center

Roulette, Jennifer W; Hill, Laura G; Diversi, Marcelo; Overath, Renee

2017-01-01

Objective: Most reports of adaptations to evidence-based prevention programmes for delivery to specific cultural groups describe formal adaptation procedures. In this paper, we report on how practitioners identify and manage issues of perceived cultural mismatch when delivering a scripted, evidence-based intervention. Design: We used grounded…

An Open Computing Infrastructure that Facilitates Integrated Product and Process Development from a Decision-Based Perspective

NASA Technical Reports Server (NTRS)

Hale, Mark A.

1996-01-01

Computer applications for design have evolved rapidly over the past several decades, and significant payoffs are being achieved by organizations through reductions in design cycle times. These applications are overwhelmed by the requirements imposed during complex, open engineering systems design. Organizations are faced with a number of different methodologies, numerous legacy disciplinary tools, and a very large amount of data. Yet they are also faced with few interdisciplinary tools for design collaboration or methods for achieving the revolutionary product designs required to maintain a competitive advantage in the future. These organizations are looking for a software infrastructure that integrates current corporate design practices with newer simulation and solution techniques. Such an infrastructure must be robust to changes in both corporate needs and enabling technologies. In addition, this infrastructure must be user-friendly, modular and scalable. This need is the motivation for the research described in this dissertation. The research is focused on the development of an open computing infrastructure that facilitates product and process design. In addition, this research explicitly deals with human interactions during design through a model that focuses on the role of a designer as that of decision-maker. The research perspective here is taken from that of design as a discipline with a focus on Decision-Based Design, Theory of Languages, Information Science, and Integration Technology. Given this background, a Model of IPPD is developed and implemented along the lines of a traditional experimental procedure: with the steps of establishing context, formalizing a theory, building an apparatus, conducting an experiment, reviewing results, and providing recommendations. Based on this Model, Design Processes and Specification can be explored in a structured and implementable architecture. An architecture for exploring design called DREAMS (Developing Robust Engineering Analysis Models and Specifications) has been developed which supports the activities of both meta-design and actual design execution. This is accomplished through a systematic process which is comprised of the stages of Formulation, Translation, and Evaluation. During this process, elements from a Design Specification are integrated into Design Processes. In addition, a software infrastructure was developed and is called IMAGE (Intelligent Multidisciplinary Aircraft Generation Environment). This represents a virtual apparatus in the Design Experiment conducted in this research. IMAGE is an innovative architecture because it explicitly supports design-related activities. This is accomplished through a GUI driven and Agent-based implementation of DREAMS. A HSCT design has been adopted from the Framework for Interdisciplinary Design Optimization (FIDO) and is implemented in IMAGE. This problem shows how Design Processes and Specification interact in a design system. In addition, the problem utilizes two different solution models concurrently: optimal and satisfying. The satisfying model allows for more design flexibility and allows a designer to maintain design freedom. As a result of following this experimental procedure, this infrastructure is an open system that it is robust to changes in both corporate needs and computer technologies. The development of this infrastructure leads to a number of significant intellectual contributions: 1) A new approach to implementing IPPD with the aid of a computer; 2) A formal Design Experiment; 3) A combined Process and Specification architecture that is language-based; 4) An infrastructure for exploring design; 5) An integration strategy for implementing computer resources; and 6) A seamless modeling language. The need for these contributions is emphasized by the demand by industry and government agencies for the development of these technologies.

Stochastic optimization of broadband reflecting photonic structures.

PubMed

Estrada-Wiese, D; Del Río-Chanona, E A; Del Río, J A

2018-01-19

Photonic crystals (PCs) are built to control the propagation of light within their structure. These can be used for an assortment of applications where custom designed devices are of interest. Among them, one-dimensional PCs can be produced to achieve the reflection of specific and broad wavelength ranges. However, their design and fabrication are challenging due to the diversity of periodic arrangement and layer configuration that each different PC needs. In this study, we present a framework to design high reflecting PCs for any desired wavelength range. Our method combines three stochastic optimization algorithms (Random Search, Particle Swarm Optimization and Simulated Annealing) along with a reduced space-search methodology to obtain a custom and optimized PC configuration. The optimization procedure is evaluated through theoretical reflectance spectra calculated by using the Equispaced Thickness Method, which improves the simulations due to the consideration of incoherent light transmission. We prove the viability of our procedure by fabricating different reflecting PCs made of porous silicon and obtain good agreement between experiment and theory using a merit function. With this methodology, diverse reflecting PCs can be designed for any applications and fabricated with different materials.

Design Considerations for Human Rating of Liquid Rocket Engines

NASA Technical Reports Server (NTRS)

Parkinson, Douglas

2010-01-01

I.Human-rating is specific to each engine; a. Context of program/project must be understood. b. Engine cannot be discussed independently from vehicle and mission. II. Utilize a logical combination of design, manufacturing, and test approaches a. Design 1) It is crucial to know the potential ways a system can fail, and how a failure can propagate; 2) Fault avoidance, fault tolerance, DFMR, caution and warning all have roles to play. b. Manufacturing and Assembly; 1) As-built vs. as-designed; 2) Review procedures for assembly and maintenance periodically; and 3) Keep personnel trained and certified. c. There is no substitute for test: 1) Analytical tools are constantly advancing, but still need test data for anchoring assumptions; 2) Demonstrate robustness and explore sensitivities; 3) Ideally, flight will be encompassed by ground test experience. III. Consistency and repeatability is key in production a. Maintain robust processes and procedures for inspection and quality control based upon development and qualification experience; b. Establish methods to "spot check" quality and consistency in parts: 1) Dedicated ground test engines; 2) Random components pulled from the line/lot to go through "enhanced" testing.

Pacing and Defibrillators in Complex Congenital Heart Disease

PubMed Central

Chubb, Henry; O’Neill, Mark; Rosenthal, Eric

2016-01-01

Device therapy in the complex congenital heart disease (CHD) population is a challenging field. There is a myriad of devices available, but none designed specifically for the CHD patient group, and a scarcity of prospective studies to guide best practice. Baseline cardiac anatomy, prior surgical and interventional procedures, existing tachyarrhythmias and the requirement for future intervention all play a substantial role in decision making. For both pacing systems and implantable cardioverter defibrillators, numerous factors impact on the merits of system location (endovascular versus non-endovascular), lead positioning, device selection and device programming. For those with Fontan circulation and following the atrial switch procedure there are also very specific considerations regarding access and potential complications. This review discusses the published guidelines, device indications and the best available evidence for guidance of device implantation in the complex CHD population. PMID:27403295

Network placement optimization for large-scale distributed system

NASA Astrophysics Data System (ADS)

Ren, Yu; Liu, Fangfang; Fu, Yunxia; Zhou, Zheng

2018-01-01

The network geometry strongly influences the performance of the distributed system, i.e., the coverage capability, measurement accuracy and overall cost. Therefore the network placement optimization represents an urgent issue in the distributed measurement, even in large-scale metrology. This paper presents an effective computer-assisted network placement optimization procedure for the large-scale distributed system and illustrates it with the example of the multi-tracker system. To get an optimal placement, the coverage capability and the coordinate uncertainty of the network are quantified. Then a placement optimization objective function is developed in terms of coverage capabilities, measurement accuracy and overall cost. And a novel grid-based encoding approach for Genetic algorithm is proposed. So the network placement is optimized by a global rough search and a local detailed search. Its obvious advantage is that there is no need for a specific initial placement. At last, a specific application illustrates this placement optimization procedure can simulate the measurement results of a specific network and design the optimal placement efficiently.

Design, fabrication and testing of porous tungsten vaporizers for mercury ion thrusters

NASA Technical Reports Server (NTRS)

Zavesky, R.; Kroeger, E.; Kami, S.

1983-01-01

The dispersions in the characteristics, performance and reliability of vaporizers for early model 30-cm thrusters were investigated. The purpose of the paper is to explore the findings and to discuss the approaches that were taken to reduce the observed dispersion and present the results of a program which validated those approaches. The information that is presented includes porous tungsten materials specifications, a discussion of assembly procedures, and a description of a test program which screens both material and fabrication processes. There are five appendices providing additional detail in the areas of vaporizer contamination, nitrogen flow testing, bubble testing, porosimeter testing, and mercury purity. Four neutralizers, seven cathodes and five main vaporizers were successfully fabricated, tested, and operated on thrusters. Performance data from those devices is presented and indicates extremely repeatable results from using the design and fabrication procedures.

Clinical Outcome Metrics for Optimization of Robust Training

NASA Technical Reports Server (NTRS)

Ebert, D.; Byrne, V. E.; McGuire, K. M.; Hurst, V. W., IV; Kerstman, E. L.; Cole, R. W.; Sargsyan, A. E.; Garcia, K. M.; Reyes, D.; Young, M.

2016-01-01

Introduction: The emphasis of this research is on the Human Research Program (HRP) Exploration Medical Capability's (ExMC) "Risk of Unacceptable Health and Mission Outcomes Due to Limitations of In-Flight Medical Capabilities." Specifically, this project aims to contribute to the closure of gap ExMC 2.02: We do not know how the inclusion of a physician crew medical officer quantitatively impacts clinical outcomes during exploration missions. The experiments are specifically designed to address clinical outcome differences between physician and non-physician cohorts in both near-term and longer-term (mission impacting) outcomes. Methods: Medical simulations will systematically compare success of individual diagnostic and therapeutic procedure simulations performed by physician and non-physician crew medical officer (CMO) analogs using clearly defined short-term (individual procedure) outcome metrics. In the subsequent step of the project, the procedure simulation outcomes will be used as input to a modified version of the NASA Integrated Medical Model (IMM) to analyze the effect of the outcome (degree of success) of individual procedures (including successful, imperfectly performed, and failed procedures) on overall long-term clinical outcomes and the consequent mission impacts. The procedures to be simulated are endotracheal intubation, fundoscopic examination, kidney/urinary ultrasound, ultrasound-guided intravenous catheter insertion, and a differential diagnosis exercise. Multiple assessment techniques will be used, centered on medical procedure simulation studies occurring at 3, 6, and 12 months after initial training (as depicted in the following flow diagram of the experiment design). Discussion: Analysis of procedure outcomes in the physician and non-physician groups and their subsets (tested at different elapsed times post training) will allow the team to 1) define differences between physician and non-physician CMOs in terms of both procedure performance (pre-IMM analysis) and overall mitigation of the mission medical impact (IMM analysis); 2) refine the procedure outcome and clinical outcome metrics themselves; 3) refine or develop innovative medical training products and solutions to maximize CMO performance; and 4) validate the methods and products of this experiment for operational use in the planning, execution, and quality assurance of the CMO training process The team has finalized training protocols and developed a software training/testing tool in collaboration with Butler Graphics (Detroit, MI). In addition to the "hands on" medical procedure modules, the software includes a differential diagnosis exercise (limited clinical decision support tool) to evaluate the diagnostic skills of participants. Human subject testing will occur over the next year.

Behavioral phenotyping of mice in pharmacological and toxicological research.

PubMed

Karl, Tim; Pabst, Reinhard; von Hörsten, Stephan

2003-07-01

The evaluation of behavioral effects is an important component for the in vivo screening of drugs or potentially toxic compounds in mice. Ideally, such screening should be composed of monitoring general health, sensory functions, and motor abilities, right before specific behavioral domains are tested. A rational strategy in the design and procedure of testing as well as an effective composition of different well-established and reproducible behavioral tests can minimize the risk of false positive and false negative results in drug screening. In the present review we describe such basic considerations in planning experiments, selecting strains of mice, and propose groups of behavioral tasks suitable for a reliable detection of differences in specific behavioral domains in mice. Screening of general health and neurophysiologic functions (reflexes, sensory abilities) and motor function (pole test, wire hang test, beam walking, rotarod, accelerod, and footprint) as well as specific hypothesis-guided testing in the behavioral domains of learning and memory (water maze, radial maze, conditioned fear, and avoidance tasks), emotionality (open field, hole board, elevated plus maze, and object exploration), nociception (tail flick, hot plate), psychiatric-like conditions (porsolt swim test, acoustic startle response, and prepulse inhibition), and aggression (isolation-induced aggression, spontaneous aggression, and territorial aggression) are described in further detail. This review is designed to describe a general approach, which increases reliability of behavioral screening. Furthermore, it provides an overview on a selection of specific procedures suitable for but not limited to behavioral screening in pharmacology and toxicology.

Just-in-time Design and Additive Manufacture of Patient-specific Medical Implants

NASA Astrophysics Data System (ADS)

Shidid, Darpan; Leary, Martin; Choong, Peter; Brandt, Milan

Recent advances in medical imaging and manufacturing science have enabled the design and production of complex, patient-specific orthopaedic implants. Additive Manufacture (AM) generates three-dimensional structures layer by layer, and is not subject to the constraints associated with traditional manufacturing methods. AM provides significant opportunities for the design of novel geometries and complex lattice structures with enhanced functional performance. However, the design and manufacture of patient-specific AM implant structures requires unique expertise in handling various optimization platforms. Furthermore, the design process for complex structures is computationally intensive. The primary aim of this research is to enable the just-in-time customisation of AM prosthesis; whereby AM implant design and manufacture be completed within the time constraints of a single surgical procedure, while minimising prosthesis mass and optimising the lattice structure to match the stiffness of the surrounding bone tissue. In this research, a design approach using raw CT scan data is applied to the AM manufacture of femoral prosthesis. Using the proposed just-in-time concept, the mass of the prosthesis was rapidly designed and manufactured while satisfying the associated structural requirements. Compressive testing of lattice structures manufactured using proposed method shows that the load carrying capacity of the resected composite bone can be recovered by up to 85% and the compressive stiffness of the AM prosthesis is statistically indistinguishable from the stiffness of the initial bone.

Application of two procedures for dual-point design of transonic airfoils

NASA Technical Reports Server (NTRS)

Mineck, Raymond E.; Campbell, Richard L.; Allison, Dennis O.

1994-01-01

Two dual-point design procedures were developed to reduce the objective function of a baseline airfoil at two design points. The first procedure to develop a redesigned airfoil used a weighted average of the shapes of two intermediate airfoils redesigned at each of the two design points. The second procedure used a weighted average of two pressure distributions obtained from an intermediate airfoil redesigned at each of the two design points. Each procedure was used to design a new airfoil with reduced wave drag at the cruise condition without increasing the wave drag or pitching moment at the climb condition. Two cycles of the airfoil shape-averaging procedure successfully designed a new airfoil that reduced the objective function and satisfied the constraints. One cycle of the target (desired) pressure-averaging procedure was used to design two new airfoils that reduced the objective function and came close to satisfying the constraints.

MyHealthAtVanderbilt: policies and procedures governing patient portal functionality

PubMed Central

Rosenbloom, S Trent; Stenner, Shane P; Anders, Shilo; Muse, Sue; Johnson, Kevin B; Jirjis, Jim; Jackson, Gretchen Purcell

2011-01-01

Explicit guidelines are needed to develop safe and effective patient portals. This paper proposes general principles, policies, and procedures for patient portal functionality based on MyHealthAtVanderbilt (MHAV), a robust portal for Vanderbilt University Medical Center. We describe policies and procedures designed to govern popular portal functions, address common user concerns, and support adoption. We present the results of our approach as overall and function-specific usage data. Five years after implementation, MHAV has over 129 800 users; 45% have used bi-directional messaging; 52% have viewed test results and 45% have viewed other medical record data; 30% have accessed health education materials; 39% have scheduled appointments; and 29% have managed a medical bill. Our policies and procedures have supported widespread adoption and use of MHAV. We believe other healthcare organizations could employ our general guidelines and lessons learned to facilitate portal implementation and usage. PMID:21807648

A CFD-based aerodynamic design procedure for hypersonic wind-tunnel nozzles

NASA Technical Reports Server (NTRS)

Korte, John J.

1993-01-01

A new procedure which unifies the best of current classical design practices, computational fluid dynamics (CFD), and optimization procedures is demonstrated for designing the aerodynamic lines of hypersonic wind-tunnel nozzles. The new procedure can be used to design hypersonic wind tunnel nozzles with thick boundary layers where the classical design procedure has been shown to break down. An efficient CFD code, which solves the parabolized Navier-Stokes (PNS) equations using an explicit upwind algorithm, is coupled to a least-squares (LS) optimization procedure. A LS problem is formulated to minimize the difference between the computed flow field and the objective function, consisting of the centerline Mach number distribution and the exit Mach number and flow angle profiles. The aerodynamic lines of the nozzle are defined using a cubic spline, the slopes of which are optimized with the design procedure. The advantages of the new procedure are that it allows full use of powerful CFD codes in the design process, solves an optimization problem to determine the new contour, can be used to design new nozzles or improve sections of existing nozzles, and automatically compensates the nozzle contour for viscous effects as part of the unified design procedure. The new procedure is demonstrated by designing two Mach 15, a Mach 12, and a Mach 18 helium nozzles. The flexibility of the procedure is demonstrated by designing the two Mach 15 nozzles using different constraints, the first nozzle for a fixed length and exit diameter and the second nozzle for a fixed length and throat diameter. The computed flow field for the Mach 15 least squares parabolized Navier-Stokes (LS/PNS) designed nozzle is compared with the classically designed nozzle and demonstrates a significant improvement in the flow expansion process and uniform core region.

Signal processing and display interface studies. [performance tests - design analysis/equipment specifications

NASA Technical Reports Server (NTRS)

1975-01-01

Signal processing equipment specifications, operating and test procedures, and systems design and engineering are described. Five subdivisions of the overall circuitry are treated: (1) the spectrum analyzer; (2) the spectrum integrator; (3) the velocity discriminator; (4) the display interface; and (5) the formatter. They function in series: (1) first in analog form to provide frequency resolution, (2) then in digital form to achieve signal to noise improvement (video integration) and frequency discrimination, and (3) finally in analog form again for the purpose of real-time display of the significant velocity data. The formatter collects binary data from various points in the processor and provides a serial output for bi-phase recording. Block diagrams are used to illustrate the system.

Eye dose to staff involved in interventional and procedural fluoroscopy

NASA Astrophysics Data System (ADS)

McLean, D.; Hadaya, D.; Tse, J.

2016-03-01

In 2011 the International Commission on Radiological Protection (ICRP) lowered the occupational eye dose limit from 150 to 20 mSv/yr [1]. While international jurisdictions are in a process of adopting these substantial changes, medical physicists at the clinical level have been advising medical colleagues on specific situations based on dose measurements. Commissioned and calibrated TLDs mounted in commercially available holders designed to simulate the measurement of Hp(3), were applied to staff involved in x-ray procedures for a one month period. During this period clinical procedure data was concurrently collected and subject to audit. The use or not of eye personal protective equipment (PPE) was noted for all staff. Audits were conducted in the cardiac catheterisation laboratory, the interventional angiography rooms and the procedural room where endoscopic retrograde cholangiopancreatography (ERCP) procedures are performed. Significant levels of occupational dose were recorded in the cardiac and interventional procedures, with maximum reading exceeding the new limit for some interventional radiologists. No significant eye doses were measured for staff performing ERCP procedures. One outcome of the studies was increased use of eye PPE for operators of interventional equipment with increased availability also to nursing staff, when standing in close proximity to the patient during procedures.

48 CFR 570.305 - Two-phase design-build selection procedures.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 4 2012-10-01 2012-10-01 false Two-phase design-build...-phase design-build selection procedures. (a) These procedures apply to acquisitions of leasehold interests if the contracting officer uses the two-phase design-build selection procedures authorized by 570...

48 CFR 570.305 - Two-phase design-build selection procedures.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 4 2014-10-01 2014-10-01 false Two-phase design-build...-phase design-build selection procedures. (a) These procedures apply to acquisitions of leasehold interests if the contracting officer uses the two-phase design-build selection procedures authorized by 570...

48 CFR 570.305 - Two-phase design-build selection procedures.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 4 2013-10-01 2013-10-01 false Two-phase design-build...-phase design-build selection procedures. (a) These procedures apply to acquisitions of leasehold interests if the contracting officer uses the two-phase design-build selection procedures authorized by 570...

48 CFR 570.305 - Two-phase design-build selection procedures.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 4 2011-10-01 2011-10-01 false Two-phase design-build...-phase design-build selection procedures. (a) These procedures apply to acquisitions of leasehold interests if the contracting officer uses the two-phase design-build selection procedures authorized by 570...

An empirical study of software design practices

NASA Technical Reports Server (NTRS)

Card, David N.; Church, Victor E.; Agresti, William W.

1986-01-01

Software engineers have developed a large body of software design theory and folklore, much of which was never validated. The results of an empirical study of software design practices in one specific environment are presented. The practices examined affect module size, module strength, data coupling, descendant span, unreferenced variables, and software reuse. Measures characteristic of these practices were extracted from 887 FORTRAN modules developed for five flight dynamics software projects monitored by the Software Engineering Laboratory (SEL). The relationship of these measures to cost and fault rate was analyzed using a contingency table procedure. The results show that some recommended design practices, despite their intuitive appeal, are ineffective in this environment, whereas others are very effective.

Electrical design for origami solar panels and a small spacecraft test mission

NASA Astrophysics Data System (ADS)

Drewelow, James; Straub, Jeremy

2017-05-01

Efficient power generation is crucial to the design of spacecraft. Mass, volume, and other limitations prevent the use of traditional spacecraft support structures from being suitable for the size of solar array required for some missions. Folding solar panel / panel array systems, however, present a number of design challenges. This paper considers the electrical design of an origami system. Specifically, it considers how to provide low impedance, durable channels for the generated power and the electrical aspects of the deployment system and procedure. The ability to dynamically reconfigure the electrical configuration of the solar cells is also discussed. Finally, a small satellite test mission to demonstrate the technology is proposed, before concluding.

Inverse load calculation procedure for offshore wind turbines and application to a 5-MW wind turbine support structure: Inverse load calculation procedure for offshore wind turbines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pahn, T.; Rolfes, R.; Jonkman, J.

A significant number of wind turbines installed today have reached their designed service life of 20 years, and the number will rise continuously. Most of these turbines promise a more economical performance if they operate for more than 20 years. To assess a continued operation, we have to analyze the load-bearing capacity of the support structure with respect to site-specific conditions. Such an analysis requires the comparison of the loads used for the design of the support structure with the actual loads experienced. This publication presents the application of a so-called inverse load calculation to a 5-MW wind turbine supportmore » structure. The inverse load calculation determines external loads derived from a mechanical description of the support structure and from measured structural responses. Using numerical simulations with the software fast, we investigated the influence of wind-turbine-specific effects such as the wind turbine control or the dynamic interaction between the loads and the support structure to the presented inverse load calculation procedure. fast is used to study the inverse calculation of simultaneously acting wind and wave loads, which has not been carried out until now. Furthermore, the application of the inverse load calculation procedure to a real 5-MW wind turbine support structure is demonstrated. In terms of this practical application, setting up the mechanical system for the support structure using measurement data is discussed. The paper presents results for defined load cases and assesses the accuracy of the inversely derived dynamic loads for both the simulations and the practical application.« less

Does neonatal pain management in intensive care units differ between night and day? An observational study.

PubMed

Guedj, Romain; Danan, Claude; Daoud, Patrick; Zupan, Véronique; Renolleau, Sylvain; Zana, Elodie; Aizenfisz, Sophie; Lapillonne, Alexandre; de Saint Blanquat, Laure; Granier, Michèle; Durand, Philippe; Castela, Florence; Coursol, Anne; Hubert, Philippe; Cimerman, Patricia; Anand, K J S; Khoshnood, Babak; Carbajal, Ricardo

2014-02-20

To determine whether analgesic use for painful procedures performed in neonates in the neonatal intensive care unit (NICU) differs during nights and days and during each of the 6 h period of the day. Conducted as part of the prospective observational Epidemiology of Painful Procedures in Neonates study which was designed to collect in real time and around-the-clock bedside data on all painful or stressful procedures. 13 NICUs and paediatric intensive care units in the Paris Region, France. All 430 neonates admitted to the participating units during a 6-week period between September 2005 and January 2006. During the first 14 days of admission, data were collected on all painful procedures and analgesic therapy. The five most frequent procedures representing 38 012 of all 42 413 (90%) painful procedures were analysed. Observational study. We compared the use of specific analgesic for procedures performed during each of the 6 h period of a day: morning (7:00 to 12:59), afternoon, early night and late night and during daytime (morning+afternoon) and night-time (early night+late night). 7724 of 38 012 (20.3%) painful procedures were carried out with a specific analgesic treatment. For morning, afternoon, early night and late night, respectively, the use of analgesic was 25.8%, 18.9%, 18.3% and 18%. The relative reduction of analgesia was 18.3%, p<0.01, between daytime and night-time and 28.8%, p<0.001, between morning and the rest of the day. Parental presence, nurses on 8 h shifts and written protocols for analgesia were associated with a decrease in this difference. The substantial differences in the use of analgesics around-the-clock may be questioned on quality of care grounds.

Comparison of 1997 Medicare relative value units for gender-specific procedures: is Adam still worth more than Eve?

PubMed

Goff, B A; Muntz, H G; Cain, J M

1997-08-01

On January 1, 1992, Congress implemented a Medicare payment system based on relative value units (RVUs). The total RVU (which is made up of work, practice, and malpractice RVUs) is multiplied by a dollar conversion factor to set the reimbursement for all procedures covered by Medicare. In a previous study, we found that significant gender bias exists in Medicare reimbursement for female-specific services. Recently, HCFA approved increases (beginning January 1997) in the work RVU for many gynecologic procedures. This study was undertaken to compare work and total RVUs for gender-specific procedures effective January 1, 1997. Using the May 1996 Federal Register, we compared work and total RVUs for 24 pairs of gender-specific procedures. The groups were matched so that the amount of work and level of difficulty would be similar, if not identical. We validated our selection of procedures for comparison by also evaluating the average time required to perform these procedures. Comparison of work RVUs for the 24 paired procedures revealed that in 19 cases (80%), male-specific procedures had a higher RVU; in 3 cases (12%), female-specific procedures were higher; and in 2 cases, there was no difference. On average, work RVUs were 49% higher for urologic procedures than for gynecologic procedures. Comparison of total RVUs revealed that in 20 cases (83%), urologic procedures had a higher total RVU and in 3 cases (12%), gynecologic procedures were higher. On average, male-specific surgeries are reimbursed at an amount which is 37% higher than that for female-specific surgeries. Recent increases in work RVUs for many gynecologic procedures have resulted in improved reimbursement. However, even with these improvements, significant gender bias still exists in the Medicare reimbursement of female-specific procedures. This gender bias is further magnified as more private insurance carriers use the system to set reimbursement.

Process for testing a xenon gas feed system of a hollow cathode assembly

NASA Technical Reports Server (NTRS)

Patterson, Michael J. (Inventor); Verhey, Timothy R. R. (Inventor); Soulas, George C. (Inventor)

2004-01-01

The design and manufacturing processes for Hollow Cathode Assemblies (HCA's) that operate over a broad range of emission currents up to 30 Amperes, at low potentials, with lifetimes in excess of 17,500 hours. The processes include contamination control procedures which cover hollow cathode component cleaning procedures, gas feed system designs and specifications, and hollow cathode activation and operating procedures to thereby produce cathode assemblies that have demonstrated stable and repeatable operating conditions, for both the discharge current and voltage. The HCA of this invention provides lifetimes of greater than 10,000 hours, and expected lifetimes of greater than 17,500 hours, whereas the present state-of-the-art is less than 500 hours at emission currents in excess of 1 Ampere. Stable operation is provided over a large range of operating emission currents, up to a 6:1 ratio, and this HCA can emit electron currents of up to 30 Amperes in magnitude to an external anode that simulates the current drawn to a space plasma, at voltages of less than 20 Volts.

Process for Ignition of Gaseous Electrical Discharge Between Electrodes of a Hollow Cathode Assembly

NASA Technical Reports Server (NTRS)

Patterson, Michael J. (Inventor); Verhey, Timothy R. R. (Inventor); Soulas, George C. (Inventor)

2000-01-01

The design and manufacturing processes for Hollow Cathode Assemblies (HCA's) that operate over a broad range of emission currents up to 30 Amperes, at low potentials, with lifetimes in excess of 17,500 hours. The processes include contamination control procedures which cover hollow cathode component cleaning procedures, gas feed system designs and specifications, and hollow cathode activation and operating procedures to thereby produce cathode assemblies that have demonstrated stable and repeatable operating conditions, for both the discharge current and voltage. The HCA of this invention provides lifetimes of greater than 10,000 hours, and expected lifetimes of greater than 17,500 hours, whereas the present state-of-the-art is less than 500 hours at emission currents in excess of 1 Ampere. Stable operation is provided over a large range of operating emission currents, up to a 6:1 ratio, and this HCA can emit electron currents of up to 30 Amperes in magnitude to an external anode that simulates the current drawn to a space plasma, at voltages of less than 20 Volts.

Space shuttle configuration accounting functional design specification

NASA Technical Reports Server (NTRS)

1974-01-01

An analysis is presented of the requirements for an on-line automated system which must be capable of tracking the status of requirements and engineering changes and of providing accurate and timely records. The functional design specification provides the definition, description, and character length of the required data elements and the interrelationship of data elements to adequately track, display, and report the status of active configuration changes. As changes to the space shuttle program levels II and III configuration are proposed, evaluated, and dispositioned, it is the function of the configuration management office to maintain records regarding changes to the baseline and to track and report the status of those changes. The configuration accounting system will consist of a combination of computers, computer terminals, software, and procedures, all of which are designed to store, retrieve, display, and process information required to track proposed and proved engineering changes to maintain baseline documentation of the space shuttle program levels II and III.

Rational design of aerobic digestion systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rich, L.G.

1987-06-01

Deficiencies are identified in state-of-the-art procedures used in the design of systems for the aerobic digestion of waste-activated sludge solids. A procedure for the design of such systems on a rational basis is presented. Such a procedure not only includes a well-defined stabilization objective, but takes into account the stabilization that occurs in the activated sludge process. Related methods are discussed by which coefficients used in the design procedure can be evaluated. A design example is given. Further research and performance data derived from systems designed by the procedure are needed to better evaluate the parameters used and to testmore » the assumptions made in applying the procedure.« less

Rational design of aerobic digestion systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rich, L.G.

1987-06-01

Deficiencies are identified in state-of-the-art procedures used in the design of systems for the aerobic digestion of waste-activated sludge solids. A procedure for the design of such systems on a rational basis is presented. Such a procedure not only includes a well-defined stabilization objective, but takes into account the stabilization that occurs in the activated sludge process. Related methods are discussed by which coefficients used in the design procedure can be evaluated. A design example is given. Further research and performance data derived from systems designed by the procedure are needed to better evaluate the parameters used and to testmore » the assumptions made in applying the procedure. (Refs. 28).« less

Most-probable-number loop-mediated isothermal amplification-based procedure enhanced with K antigen-specific immunomagnetic separation for quantifying tdh(+) Vibrio parahaemolyticus in molluscan Shellfish.

PubMed

Tanaka, Natsuko; Iwade, Yoshito; Yamazaki, Wataru; Gondaira, Fumio; Vuddhakul, Varaporn; Nakaguchi, Yoshitsugu; Nishibuchi, Mitsuaki

2014-07-01

Although thermostable direct hemolysin-producing (tdh(+)) Vibrio parahaemolyticus is the leading cause of seafood-borne gastroenteritis, the enumeration of tdh(+) V. parahaemolyticus remains challenging due to its low densities in the environment. In this study, we developed a most-probable-number (MPN)-based procedure designated A-IS(1)-LAMP, in which an immunomagnetic separation (IMS) technique targeting as many as 69 established K antigens and a loop-mediated isothermal amplification (LAMP) assay targeting the thermostable direct hemolysin (tdh) gene were applied in an MPN format. Our IMS employed PickPen, an eight-channel intrasolution magnetic particle separation device, which enabled a straightforward microtiter plate-based IMS procedure (designated as PickPen-IMS). The ability of the procedure to quantify a wide range of tdh(+) V. parahaemolyticus levels was evaluated by testing shellfish samples in Japan and southern Thailand, where shellfish products are known to contain relatively low and high levels of total V. parahaemolyticus, respectively. The Japanese and Thai shellfish samples showed, respectively, relatively low (< 3 to 11 MPN/10 g) and considerably higher (930 to 110,000 MPN/10 g) levels of tdh(+) V. parahaemolyticus, raising concern about the safety of Thai shellfish products sold to domestic consumers at local morning markets. LAMP showed similar or higher performance than conventional PCR in the detection and quantification of a wide range of tdh(+) V. parahaemolyticus levels in shellfish products. Whereas a positive effect of PickPen-IMS was not observed in MPN determination, PickPen-IMS was able to concentrate tdh(+) V. parahaemolyticus 32-fold on average from the Japanese shellfish samples at an individual tube level, suggesting a possibility of using PickPen-IMS as an optional tool for specific shellfish samples. The A-IS(1)-LAMP procedure can be used by any health authority in the world to measure the tdh(+) V. parahaemolyticus levels in shellfish products.

What Is Essential in Developmental Evaluation? On Integrity, Fidelity, Adultery, Abstinence, Impotence, Long-Term Commitment, Integrity, and Sensitivity in Implementing Evaluation Models

ERIC Educational Resources Information Center

Patton, Michael Quinn

2016-01-01

Fidelity concerns the extent to which a specific evaluation sufficiently incorporates the core characteristics of the overall approach to justify labeling that evaluation by its designated name. Fidelity has traditionally meant implementing a model in exactly the same way each time following the prescribed steps and procedures. The essential…

The Observer Effect and Its Impact on Staff Behavior in an Acquired Brain Injury Neurobehavioral Treatment Setting

ERIC Educational Resources Information Center

Guercio, John M.; Dixon, Mark R.

2011-01-01

Staff in three neurobehavioral residential settings (5 in each residence for a total of 15 staff) were trained on specific positive interaction behaviors in a multiple baseline design. Staff in each of the residences were provided with recommended behaviors for interacting with residents through an observational procedure where they observed and…

Design and Implementation of a Multimedia CD-ROM-Based Directed Study Preservice Teacher Education Course.

ERIC Educational Resources Information Center

Morse, Timothy

This paper discusses the development and implementation of a computer-based directed study preservice teacher education course. Specifically, it explains the procedures followed to create the ten multimedia CD-ROMs that comprise the course, and how preservice teachers use the CD-ROMs. Topics to be covered include (1) rationale for course creation;…

Into the Curriculum. Art: Whistler's Mother; Reading/Language Arts: Finding My Voice; Science: Where on My Tongue? Taste; Social Studies/Science: Volcanoes; Social Studies: Pompeii.

ERIC Educational Resources Information Center

Reed-Mundell, Charlie

2001-01-01

Provides five fully developed library media activities that are designed for use with specific curriculum units in art, reading, language arts, science, and social studies. Describes library media skills, curriculum objectives, grade levels, resources, instructional roles, procedures, evaluation, and follow-up for each activity. (LRW)

Journal Benchmarking for Strategic Publication Management and for Improving Journal Positioning in the World Ranking Systems

ERIC Educational Resources Information Center

Moskovkin, Vladimir M.; Bocharova, Emilia A.; Balashova, Oksana V.

2014-01-01

Purpose: The purpose of this paper is to introduce and develop the methodology of journal benchmarking. Design/Methodology/ Approach: The journal benchmarking method is understood to be an analytic procedure of continuous monitoring and comparing of the advance of specific journal(s) against that of competing journals in the same subject area,…

Crew Communication as a Factor in Aviation Accidents

NASA Technical Reports Server (NTRS)

Goguen, J. A.; Linde, C.; Murphy, M.

1984-01-01

The incidence of air transport accidents caused by problems in crew communication and coordination was investigated. Communication patterns which are most effective in specific situations were determined. Methods to assess the effectiveness of crew communication patterns were developed. The results lead to the development of new methods training crews in effective communication and provide guidelines for the design of aviation procedures and equipment.

AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT XXIV, MICHIGAN/CLARK TRANSMISSION--OIL FLOW THROUGH THE CONTROL COVER ASSEMBLY.

ERIC Educational Resources Information Center

Human Engineering Inst., Cleveland, OH.

THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE SERVICING PROCEDURES FOR THE CONTROL SYSTEM OF A SPECIFIC TRANSMISSION USED ON DIESEL POWERED EQUIPMENT. TOPICS ARE EXAMINING THE CONTROL COVER ASSEMBLY, REGULATING VALVE AND SAFETY VALVE, AND INSPECTING THE SYSTEM. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL…