Virtual Control Systems Environment (VCSE)

ScienceCinema

Atkins, Will

2018-02-14

Will Atkins, a Sandia National Laboratories computer engineer discusses cybersecurity research work for process control systems. Will explains his work on the Virtual Control Systems Environment project to develop a modeling and simulation framework of the U.S. electric grid in order to study and mitigate possible cyberattacks on infrastructure.

Adaptive process control using fuzzy logic and genetic algorithms

NASA Technical Reports Server (NTRS)

Karr, C. L.

1993-01-01

Researchers at the U.S. Bureau of Mines have developed adaptive process control systems in which genetic algorithms (GA's) are used to augment fuzzy logic controllers (FLC's). GA's are search algorithms that rapidly locate near-optimum solutions to a wide spectrum of problems by modeling the search procedures of natural genetics. FLC's are rule based systems that efficiently manipulate a problem environment by modeling the 'rule-of-thumb' strategy used in human decision making. Together, GA's and FLC's possess the capabilities necessary to produce powerful, efficient, and robust adaptive control systems. To perform efficiently, such control systems require a control element to manipulate the problem environment, and a learning element to adjust to the changes in the problem environment. Details of an overall adaptive control system are discussed. A specific laboratory acid-base pH system is used to demonstrate the ideas presented.

Controlling quantum memory-assisted entropic uncertainty in non-Markovian environments

NASA Astrophysics Data System (ADS)

Zhang, Yanliang; Fang, Maofa; Kang, Guodong; Zhou, Qingping

2018-03-01

Quantum memory-assisted entropic uncertainty relation (QMA EUR) addresses that the lower bound of Maassen and Uffink's entropic uncertainty relation (without quantum memory) can be broken. In this paper, we investigated the dynamical features of QMA EUR in the Markovian and non-Markovian dissipative environments. It is found that dynamical process of QMA EUR is oscillation in non-Markovian environment, and the strong interaction is favorable for suppressing the amount of entropic uncertainty. Furthermore, we presented two schemes by means of prior weak measurement and posterior weak measurement reversal to control the amount of entropic uncertainty of Pauli observables in dissipative environments. The numerical results show that the prior weak measurement can effectively reduce the wave peak values of the QMA-EUA dynamic process in non-Markovian environment for long periods of time, but it is ineffectual on the wave minima of dynamic process. However, the posterior weak measurement reversal has an opposite effects on the dynamic process. Moreover, the success probability entirely depends on the quantum measurement strength. We hope that our proposal could be verified experimentally and might possibly have future applications in quantum information processing.

An RFID-Based Manufacturing Control Framework for Loosely Coupled Distributed Manufacturing System Supporting Mass Customization

NASA Astrophysics Data System (ADS)

Chen, Ruey-Shun; Tsai, Yung-Shun; Tu, Arthur

In this study we propose a manufacturing control framework based on radio-frequency identification (RFID) technology and a distributed information system to construct a mass-customization production process in a loosely coupled shop-floor control environment. On the basis of this framework, we developed RFID middleware and an integrated information system for tracking and controlling the manufacturing process flow. A bicycle manufacturer was used to demonstrate the prototype system. The findings of this study were that the proposed framework can improve the visibility and traceability of the manufacturing process as well as enhance process quality control and real-time production pedigree access. Using this framework, an enterprise can easily integrate an RFID-based system into its manufacturing environment to facilitate mass customization and a just-in-time production model.

Evocative gene–environment correlation in the mother–child relationship: A twin study of interpersonal processes

PubMed Central

KLAHR, ASHLEA M.; THOMAS, KATHERINE M.; HOPWOOD, CHRISTOPHER J.; KLUMP, KELLY L.; BURT, S. ALEXANDRA

2014-01-01

The behavior genetic literature suggests that genetically influenced characteristics of the child elicit specific behaviors from the parent. However, little is known about the processes by which genetically influenced child characteristics evoke parental responses. Interpersonal theory provides a useful framework for identifying reciprocal behavioral processes between children and mothers. The theory posits that, at any given moment, interpersonal behavior varies along the orthogonal dimensions of warmth and control and that the interpersonal behavior of one individual tends to elicit corresponding or contrasting behavior from the other (i.e., warmth elicits warmth, whereas control elicits submission). The current study thus examined these dimensions of interpersonal behavior as they relate to the parent–child relationship in 546 twin families. A computer joystick was used to rate videos of mother–child interactions in real time, yielding information on mother and child levels of warmth and control throughout the interaction. Analyses indicated that maternal control, but not maternal warmth, was influenced by evocative gene–environment correlational processes, such that genetic influences on maternal control and child control were largely overlapping. Moreover, these common genetic influences were present both cross-sectionally and over the course of the interaction. Such findings not only confirm the presence of evocative gene–environment correlational processes in the mother–child relationship but also illuminate at least one of the specific interpersonal behaviors that underlie this evocative process. PMID:23398756

40 CFR 63.487 - Batch front-end process vents-reference control technology.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-reference control technology. 63.487 Section 63.487 Protection of Environment ENVIRONMENTAL PROTECTION... SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutant Emissions: Group I Polymers and Resins § 63.487 Batch front-end process vents—reference control technology. (a) Batch front-end process...

40 CFR 63.487 - Batch front-end process vents-reference control technology.

Code of Federal Regulations, 2011 CFR

2011-07-01

... control technology. 63.487 Section 63.487 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... CATEGORIES National Emission Standards for Hazardous Air Pollutant Emissions: Group I Polymers and Resins § 63.487 Batch front-end process vents—reference control technology. (a) Batch front-end process vents...

40 CFR 63.487 - Batch front-end process vents-reference control technology.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-reference control technology. 63.487 Section 63.487 Protection of Environment ENVIRONMENTAL PROTECTION... SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutant Emissions: Group I Polymers and Resins § 63.487 Batch front-end process vents—reference control technology. (a) Batch front-end process...

40 CFR 63.487 - Batch front-end process vents-reference control technology.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-reference control technology. 63.487 Section 63.487 Protection of Environment ENVIRONMENTAL PROTECTION... SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutant Emissions: Group I Polymers and Resins § 63.487 Batch front-end process vents—reference control technology. (a) Batch front-end process...

Implementation of ionizing radiation environment requirements for Space Station

NASA Technical Reports Server (NTRS)

Boeder, Paul A.; Watts, John W.

1993-01-01

Proper functioning of Space Station hardware requires that the effects of high-energy ionizing particles from the natural environment and (possibly) from man-made sources be considered during design. At the Space Station orbit of 28.5-deg inclination and 330-440 km altitude, geomagnetically trapped protons and electrons contribute almost all of the dose, while galactic cosmic rays and anomalous cosmic rays may produce Single Event Upsets (SEUs), latchups, and burnouts of microelectronic devices. Implementing ionizing radiation environment requirements for Space Station has been a two part process, including the development of a description of the environment for imposing requirements on the design and the development of a control process for assessing how well the design addresses the effects of the ionizing radiation environment. We will review both the design requirements and the control process for addressing ionizing radiation effects on Space Station.

An architecture for heuristic control of real-time processes

NASA Technical Reports Server (NTRS)

Raulefs, P.; Thorndyke, P. W.

1987-01-01

Abstract Process management combines complementary approaches of heuristic reasoning and analytical process control. Management of a continuous process requires monitoring the environment and the controlled system, assessing the ongoing situation, developing and revising planned actions, and controlling the execution of the actions. For knowledge-intensive domains, process management entails the potentially time-stressed cooperation among a variety of expert systems. By redesigning a blackboard control architecture in an object-oriented framework, researchers obtain an approach to process management that considerably extends blackboard control mechanisms and overcomes limitations of blackboard systems.

Parental Low Self-Control, Family Environments, and Juvenile Delinquency.

PubMed

Meldrum, Ryan C; Connolly, George M; Flexon, Jamie; Guerette, Rob T

2016-10-01

Research consistently finds that low self-control is significantly correlated with delinquency. Only recently, however, have researchers started to examine associations between parental low self-control, family environments, and child antisocial behavior. Adding to this emerging area of research, the current study examines associations between parental low self-control, aspects of the family environment, and officially recoded juvenile delinquency among a sample (N = 101) of juveniles processed through a juvenile justice assessment facility located in the Southeastern United States. Furthermore, it considers whether aspects of family environments, particularly family cohesion, family conflict, and parental efficacy, mediate the influence of parental low self-control on delinquency. The results of a series of analyses indicate that parental low self-control is correlated with various aspects of family environments and juvenile delinquency, and that the association between parental low self-control and juvenile delinquency is mediated by family environments. Supplementary analyses also suggest that the association between parental low self-control and the family environment may be reciprocal. © The Author(s) 2015.

Systems view on spatial planning and perception based on invariants in agent-environment dynamics

PubMed Central

Mettler, Bérénice; Kong, Zhaodan; Li, Bin; Andersh, Jonathan

2015-01-01

Modeling agile and versatile spatial behavior remains a challenging task, due to the intricate coupling of planning, control, and perceptual processes. Previous results have shown that humans plan and organize their guidance behavior by exploiting patterns in the interactions between agent or organism and the environment. These patterns, described under the concept of Interaction Patterns (IPs), capture invariants arising from equivalences and symmetries in the interaction with the environment, as well as effects arising from intrinsic properties of human control and guidance processes, such as perceptual guidance mechanisms. The paper takes a systems' perspective, considering the IP as a unit of organization, and builds on its properties to present a hierarchical model that delineates the planning, control, and perceptual processes and their integration. The model's planning process is further elaborated by showing that the IP can be abstracted, using spatial time-to-go functions. The perceptual processes are elaborated from the hierarchical model. The paper provides experimental support for the model's ability to predict the spatial organization of behavior and the perceptual processes. PMID:25628524

Differentiated Learning Environment--A Classroom for Quadratic Equation, Function and Graphs

ERIC Educational Resources Information Center

Dinç, Emre

2017-01-01

This paper will cover the design of a learning environment as a classroom regarding the Quadratic Equations, Functions and Graphs. The goal of the learning environment offered in the paper is to design a classroom where students will enjoy the process, use their skills they already have during the learning process, control and plan their learning…

The Acquisition of Integrated Science Process Skills in a Web-Based Learning Environment

ERIC Educational Resources Information Center

Saat, Rohaida Mohd

2004-01-01

Web-based learning is becoming prevalent in science learning. Some use specially designed programs, while others use materials available on the Internet. This qualitative case study examined the process of acquisition of integrated science process skills, particularly the skill of controlling variables, in a web-based learning environment among…

Online sensing and control of oil in process wastewater

NASA Astrophysics Data System (ADS)

Khomchenko, Irina B.; Soukhomlinoff, Alexander D.; Mitchell, T. F.; Selenow, Alexander E.

2002-02-01

Industrial processes, which eliminate high concentration of oil in their waste stream, find it extremely difficult to measure and control the water purification process. Most oil separation processes involve chemical separation using highly corrosive caustics, acids, surfactants, and emulsifiers. Included in the output of this chemical treatment process are highly adhesive tar-like globules, emulsified and surface oils, and other emulsified chemicals, in addition to suspended solids. The level of oil/hydrocarbons concentration in the wastewater process may fluctuate from 1 ppm to 10,000 ppm, depending upon the specifications of the industry and level of water quality control. The authors have developed a sensing technology, which provides the accuracy of scatter/absorption sensing in a contactless environment by combining these methodologies with reflective measurement. The sensitivity of the sensor may be modified by changing the fluid level control in the flow cell, allowing for a broad range of accurate measurement from 1 ppm to 10,000 ppm. Because this sensing system has been designed to work in a highly invasive environment, it can be placed close to the process source to allow for accurate real time measurement and control.

40 CFR 61.181 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... cooled, condensed, and removed in a solid form. Control device means the air pollution control equipment... failure of air pollution control equipment or process equipment or of a process to operate in a normal or... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL...

40 CFR 61.181 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... cooled, condensed, and removed in a solid form. Control device means the air pollution control equipment... failure of air pollution control equipment or process equipment or of a process to operate in a normal or... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL...

40 CFR 61.181 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... cooled, condensed, and removed in a solid form. Control device means the air pollution control equipment... failure of air pollution control equipment or process equipment or of a process to operate in a normal or... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL...

40 CFR 61.181 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... cooled, condensed, and removed in a solid form. Control device means the air pollution control equipment... failure of air pollution control equipment or process equipment or of a process to operate in a normal or... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL...

40 CFR 61.181 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... cooled, condensed, and removed in a solid form. Control device means the air pollution control equipment... failure of air pollution control equipment or process equipment or of a process to operate in a normal or... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL...

External Contamination Control of Attached Payloads on the International Space Station

NASA Technical Reports Server (NTRS)

Soares, Carlos E.; Mikatarian, Ronald R.; Olsen, Randy L.; Huang, Alvin Y.; Steagall, Courtney A.; Schmidl, William D.; Wright, Bruce D.; Koontz, Steven

2012-01-01

The International Space Station (ISS) is an on-orbit platform for science utilization in low Earth orbit with multiple sites for external payloads with exposure to the natural and induced environments. Contamination is one of the induced environments that can impact performance, mission success and science utilization on the vehicle. This paper describes the external contamination control requirements and integration process for externally mounted payloads on the ISS. The external contamination control requirements are summarized and a description of the integration and verification process is detailed to guide payload developers in the certification process of attached payloads on the vehicle. A description of the required data certification deliverables covers the characterization of contamination sources. Such characterization includes identification, usage and operational data for each class of contamination source. Classes of external contamination sources covered are vacuum exposed materials, sources of leakage, vacuum venting and thrusters. ISS system level analyses are conducted by the ISS Space Environments Team to certify compliance with external contamination control requirements. This paper also addresses the ISS induced contamination environment at attached payload sites, both at the requirements level as well as measurements made on ISS.

Potential Scenarios for Nanomaterial Release and Subsequent Alteration in the Environment

EPA Science Inventory

The risk associated with engineered nanomaterials (ENMs) will be determined in part by the processes that control their environmental fate and transformation. These processes act not only on ENMs that might be released directly to the environment, but perhaps more importantly als...

ARSENIC UPTAKE PROCESSES IN REDUCING ENVIRONMENTS: IMPLICATIONS FOR ACTIVE REMEDIATION AND NATURAL ATTENUATION

EPA Science Inventory

Reductive dissolution of iron oxyhydr(oxides) and release of adsorbed or coprecipitated arsenic is often implicated as a key process that controls the mobility and bioavailability of arsenic in anoxic environments. Yet a complete assessment of arsenic transport and fate requires...

A Learning Model for Enhancing the Student's Control in Educational Process Using Web 2.0 Personal Learning Environments

ERIC Educational Resources Information Center

Rahimi, Ebrahim; van den Berg, Jan; Veen, Wim

2015-01-01

In recent educational literature, it has been observed that improving student's control has the potential of increasing his or her feeling of ownership, personal agency and activeness as means to maximize his or her educational achievement. While the main conceived goal for personal learning environments (PLEs) is to increase student's control by…

Boys' serotonin transporter genotype affects maternal behavior through self-control: a case of evocative gene-environment correlation.

PubMed

Pener-Tessler, Roni; Avinun, Reut; Uzefovsky, Florina; Edelman, Shany; Ebstein, Richard P; Knafo, Ariel

2013-02-01

Self-control, involving processes such as delaying gratification, concentrating, planning, following instructions, and adapting emotions and behavior to situational requirements and social norms, may have a profound impact on children's adjustment. The importance of self-control suggests that parents are likely to modify their parenting based on children's ability for self-control. We study the effect of children's self-control, a trait partially molded by genetics, on their mothers' parenting, a process of evocative gene-environment correlation. Israeli 3.5-year-old twins (N = 320) participated in a lab session in which their mothers' parenting was observed. DNA was available from most children (N = 228). Mothers described children's self-control in a questionnaire. Boys were lower in self-control and received less positive parenting from their mothers, in comparison with girls. For boys, and not for girls, the serotonin transporter linked polymorphic region gene predicted mothers' levels of positive parenting, an effect mediated by boys' self-control. The implications of this evocative gene-environment correlation and the observed sex differences are discussed.

Seek and destroy process: Listeria monocytogenes process controls in the ready-to-eat meat and poultry industry.

PubMed

Malley, Thomas J V; Butts, John; Wiedmann, Martin

2015-02-01

The majority of human listeriosis cases appear to be caused by consumption of ready-to-eat (RTE) foods contaminated at the time of consumption with high levels of Listeria monocytogenes. Although strategies to prevent growth of L. monocytogenes in RTE products are critical for reducing the incidence of human listeriosis, control of postprocessing environmental contamination of RTE meat and poultry products is an essential component of a comprehensive L. monocytogenes intervention and control program. Complete elimination of postprocessing L. monocytogenes contamination is challenging because this pathogen is common in various environments outside processing plants and can persist in food processing environments for years. Persistent L. monocytogenes strains in processing plants have been identified as the most common postprocessing contaminants of RTE foods and the cause of multiple listeriosis outbreaks. Identification and elimination of L. monocytogenes strains persisting in processing plants is thus critical for (i) compliance with zero-tolerance regulations for L. monocytogenes in U.S. RTE meat and poultry products and (ii) reduction of the incidence of human listeriosis. The seek-and-destroy process is a systematic approach to finding sites of persistent strains (niches) in food processing plants, with the goal of either eradicating or mitigating effects of these strains. This process has been used effectively to address persistent L. monocytogenes contamination in food processing plants, as supported by peer-reviewed evidence detailed here. Thus, a regulatory environment that encourages aggressive environmental Listeria testing is required to facilitate continued use of this science-based strategy for controlling L. monocytogenes in RTE foods.

Cardea: Providing Support for Dynamic Resource Access in a Distributed Computing Environment

NASA Technical Reports Server (NTRS)

Lepro, Rebekah

2003-01-01

The environment framing the modem authorization process span domains of administration, relies on many different authentication sources, and manages complex attributes as part of the authorization process. Cardea facilitates dynamic access control within this environment as a central function of an inter-operable authorization framework. The system departs from the traditional authorization model by separating the authentication and authorization processes, distributing the responsibility for authorization data and allowing collaborating domains to retain control over their implementation mechanisms. Critical features of the system architecture and its handling of the authorization process differentiate the system from existing authorization components by addressing common needs not adequately addressed by existing systems. Continuing system research seeks to enhance the implementation of the current authorization model employed in Cardea, increase the robustness of current features, further the framework for establishing trust and promote interoperability with existing security mechanisms.

Impact of Operating Context on the Use of Structure in Air Traffic Controller Cognitive Processes

NASA Technical Reports Server (NTRS)

Davison, Hayley J.; Histon, Jonathan M.; Ragnarsdottir, Margret Dora; Major, Laura M.; Hansman, R. John

2004-01-01

This paper investigates the influence of structure on air traffic controllers cognitive processes in the TRACON, En Route, and Oceanic environments. Radar data and voice command analyses were conducted to support hypotheses generated through observations and interviews conducted at the various facilities. Three general types of structure-based abstractions (standard flows, groupings, and critical points) have been identified as being used in each context, though the details of their application varied in accordance with the constraints of the particular operational environment. Projection emerged as a key cognitive process aided by the structure-based abstractions, and there appears to be a significant difference between how time-based versus spatial-based projection is performed by controllers. It is recommended that consideration be given to the value provided by the structure-based abstractions to the controller as well as to maintain consistency between the type (time or spatial) of information support provided to the controller.

Distributed automatic control of technological processes in conditions of weightlessness

NASA Technical Reports Server (NTRS)

Kukhtenko, A. I.; Merkulov, V. I.; Samoylenko, Y. I.; Ladikov-Royev, Y. P.

1986-01-01

Some problems associated with the automatic control of liquid metal and plasma systems under conditions of weightlessness are examined, with particular reference to the problem of stability of liquid equilibrium configurations. The theoretical fundamentals of automatic control of processes in electrically conducting continuous media are outlined, and means of using electromagnetic fields for simulating technological processes in a space environment are discussed.

76 FR 17145 - Agency Information Collection Activities: Business Transformation-Automated Integrated Operating...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-28

... Collection Activities: Business Transformation--Automated Integrated Operating Environment (IOE), New... Transformation--Integrated Operating Environment (IOE); OMB Control No. 1615-NEW. SUMMARY: USCIS is developing an automated Integrated Operating Environment (IOE) to process benefit applications. The IOE will collect...

Evolutionary game dynamics of controlled and automatic decision-making

NASA Astrophysics Data System (ADS)

Toupo, Danielle F. P.; Strogatz, Steven H.; Cohen, Jonathan D.; Rand, David G.

2015-07-01

We integrate dual-process theories of human cognition with evolutionary game theory to study the evolution of automatic and controlled decision-making processes. We introduce a model in which agents who make decisions using either automatic or controlled processing compete with each other for survival. Agents using automatic processing act quickly and so are more likely to acquire resources, but agents using controlled processing are better planners and so make more effective use of the resources they have. Using the replicator equation, we characterize the conditions under which automatic or controlled agents dominate, when coexistence is possible and when bistability occurs. We then extend the replicator equation to consider feedback between the state of the population and the environment. Under conditions in which having a greater proportion of controlled agents either enriches the environment or enhances the competitive advantage of automatic agents, we find that limit cycles can occur, leading to persistent oscillations in the population dynamics. Critically, however, these limit cycles only emerge when feedback occurs on a sufficiently long time scale. Our results shed light on the connection between evolution and human cognition and suggest necessary conditions for the rise and fall of rationality.

Evolutionary game dynamics of controlled and automatic decision-making.

PubMed

Toupo, Danielle F P; Strogatz, Steven H; Cohen, Jonathan D; Rand, David G

2015-07-01

We integrate dual-process theories of human cognition with evolutionary game theory to study the evolution of automatic and controlled decision-making processes. We introduce a model in which agents who make decisions using either automatic or controlled processing compete with each other for survival. Agents using automatic processing act quickly and so are more likely to acquire resources, but agents using controlled processing are better planners and so make more effective use of the resources they have. Using the replicator equation, we characterize the conditions under which automatic or controlled agents dominate, when coexistence is possible and when bistability occurs. We then extend the replicator equation to consider feedback between the state of the population and the environment. Under conditions in which having a greater proportion of controlled agents either enriches the environment or enhances the competitive advantage of automatic agents, we find that limit cycles can occur, leading to persistent oscillations in the population dynamics. Critically, however, these limit cycles only emerge when feedback occurs on a sufficiently long time scale. Our results shed light on the connection between evolution and human cognition and suggest necessary conditions for the rise and fall of rationality.

[Development of whole process quality control and management system of traditional Chinese medicine decoction pieces based on traditional Chinese medicine quality tree].

PubMed

Yu, Wen-Kang; Dong, Ling; Pei, Wen-Xuan; Sun, Zhi-Rong; Dai, Jun-Dong; Wang, Yun

2017-12-01

The whole process quality control and management of traditional Chinese medicine (TCM) decoction pieces is a system engineering, involving the base environment, seeds and seedlings, harvesting, processing and other multiple steps, so the accurate identification of factors in TCM production process that may induce the quality risk, as well as reasonable quality control measures are very important. At present, the concept of quality risk is mainly concentrated in the aspects of management and regulations, etc. There is no comprehensive analysis on possible risks in the quality control process of TCM decoction pieces, or analysis summary of effective quality control schemes. A whole process quality control and management system for TCM decoction pieces based on TCM quality tree was proposed in this study. This system effectively combined the process analysis method of TCM quality tree with the quality risk management, and can help managers to make real-time decisions while realizing the whole process quality control of TCM. By providing personalized web interface, this system can realize user-oriented information feedback, and was convenient for users to predict, evaluate and control the quality of TCM. In the application process, the whole process quality control and management system of the TCM decoction pieces can identify the related quality factors such as base environment, cultivation and pieces processing, extend and modify the existing scientific workflow according to their own production conditions, and provide different enterprises with their own quality systems, to achieve the personalized service. As a new quality management model, this paper can provide reference for improving the quality of Chinese medicine production and quality standardization. Copyright© by the Chinese Pharmaceutical Association.

Design of supply chain in fuzzy environment

NASA Astrophysics Data System (ADS)

Rao, Kandukuri Narayana; Subbaiah, Kambagowni Venkata; Singh, Ganja Veera Pratap

2013-05-01

Nowadays, customer expectations are increasing and organizations are prone to operate in an uncertain environment. Under this uncertain environment, the ultimate success of the firm depends on its ability to integrate business processes among supply chain partners. Supply chain management emphasizes cross-functional links to improve the competitive strategy of organizations. Now, companies are moving from decoupled decision processes towards more integrated design and control of their components to achieve the strategic fit. In this paper, a new approach is developed to design a multi-echelon, multi-facility, and multi-product supply chain in fuzzy environment. In fuzzy environment, mixed integer programming problem is formulated through fuzzy goal programming in strategic level with supply chain cost and volume flexibility as fuzzy goals. These fuzzy goals are aggregated using minimum operator. In tactical level, continuous review policy for controlling raw material inventories in supplier echelon and controlling finished product inventories in plant as well as distribution center echelon is considered as fuzzy goals. A non-linear programming model is formulated through fuzzy goal programming using minimum operator in the tactical level. The proposed approach is illustrated with a numerical example.

Genetic algorithms in adaptive fuzzy control

NASA Technical Reports Server (NTRS)

Karr, C. Lucas; Harper, Tony R.

1992-01-01

Researchers at the U.S. Bureau of Mines have developed adaptive process control systems in which genetic algorithms (GA's) are used to augment fuzzy logic controllers (FLC's). GA's are search algorithms that rapidly locate near-optimum solutions to a wide spectrum of problems by modeling the search procedures of natural genetics. FLC's are rule based systems that efficiently manipulate a problem environment by modeling the 'rule-of-thumb' strategy used in human decision making. Together, GA's and FLC's possess the capabilities necessary to produce powerful, efficient, and robust adaptive control systems. To perform efficiently, such control systems require a control element to manipulate the problem environment, an analysis element to recognize changes in the problem environment, and a learning element to adjust fuzzy membership functions in response to the changes in the problem environment. Details of an overall adaptive control system are discussed. A specific computer-simulated chemical system is used to demonstrate the ideas presented.

Switching the JLab Accelerator Operations Environment from an HP-UX Unix-based to a PC/Linux-based environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mcguckin, Theodore

2008-10-01

The Jefferson Lab Accelerator Controls Environment (ACE) was predominantly based on the HP-UX Unix platform from 1987 through the summer of 2004. During this period the Accelerator Machine Control Center (MCC) underwent a major renovation which included introducing Redhat Enterprise Linux machines, first as specialized process servers and then gradually as general login servers. As computer programs and scripts required to run the accelerator were modified, and inherent problems with the HP-UX platform compounded, more development tools became available for use with Linux and the MCC began to be converted over. In May 2008 the last HP-UX Unix login machinemore » was removed from the MCC, leaving only a few Unix-based remote-login servers still available. This presentation will explore the process of converting an operational Control Room environment from the HP-UX to Linux platform as well as the many hurdles that had to be overcome throughout the transition period (including a discussion of« less

To Meet or Not To Meet Physical vs. Virtual Configuration Control Board

NASA Technical Reports Server (NTRS)

Rice, Shelley

2017-01-01

This presentation will define the CCB, discuss its functions and members. We will look into traditional processes of managing change control via the CCB meeting and advanced practices utilizing enhanced product tools and technologies. Well step through a summary of the feedback from the community of CM professionals at NASA Goddard Space Flight Center of best practices as well as pros and cons for facilitating both a physical CCB and managing stakeholder approvals in a virtual environment. Attendees will come away with current industry strategies to determine if process for managing change control and approvals can be streamlined within their local work environments.

Human Factors Considerations in System Design

NASA Technical Reports Server (NTRS)

Mitchell, C. M. (Editor); Vanbalen, P. M. (Editor); Moe, K. L. (Editor)

1983-01-01

Human factors considerations in systems design was examined. Human factors in automated command and control, in the efficiency of the human computer interface and system effectiveness are outlined. The following topics are discussed: human factors aspects of control room design; design of interactive systems; human computer dialogue, interaction tasks and techniques; guidelines on ergonomic aspects of control rooms and highly automated environments; system engineering for control by humans; conceptual models of information processing; information display and interaction in real time environments.

Security Implications of OPC, OLE, DCOM, and RPC in Control Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2006-01-01

OPC is a collection of software programming standards and interfaces used in the process control industry. It is intended to provide open connectivity and vendor equipment interoperability. The use of OPC technology simplifies the development of control systems that integrate components from multiple vendors and support multiple control protocols. OPC-compliant products are available from most control system vendors, and are widely used in the process control industry. OPC was originally known as OLE for Process Control; the first standards for OPC were based on underlying services in the Microsoft Windows computing environment. These underlying services (OLE [Object Linking and Embedding],more » DCOM [Distributed Component Object Model], and RPC [Remote Procedure Call]) have been the source of many severe security vulnerabilities. It is not feasible to automatically apply vendor patches and service packs to mitigate these vulnerabilities in a control systems environment. Control systems using the original OPC data access technology can thus inherit the vulnerabilities associated with these services. Current OPC standardization efforts are moving away from the original focus on Microsoft protocols, with a distinct trend toward web-based protocols that are independent of any particular operating system. However, the installed base of OPC equipment consists mainly of legacy implementations of the OLE for Process Control protocols.« less

40 CFR 63.497 - Back-end process provisions-monitoring provisions for control and recovery devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Back-end process provisions-monitoring... Polymers and Resins § 63.497 Back-end process provisions—monitoring provisions for control and recovery devices. (a) An owner or operator complying with the residual organic HAP limitations in § 63.494(a) using...

Disciplined Decision Making in an Interdisciplinary Environment: Some Implications for Clinical Applications of Statistical Process Control.

ERIC Educational Resources Information Center

Hantula, Donald A.

1995-01-01

Clinical applications of statistical process control (SPC) in human service organizations are considered. SPC is seen as providing a standard set of criteria that serves as a common interface for data-based decision making, which may bring decision making under the control of established contingencies rather than the immediate contingencies of…

Attention and Cognitive Control Networks Assessed in a Dichotic Listening fMRI Study

ERIC Educational Resources Information Center

Falkenberg, Liv E.; Specht, Karsten; Westerhausen, Rene

2011-01-01

A meaningful interaction with our environment relies on the ability to focus on relevant sensory input and to ignore irrelevant information, i.e. top-down control and attention processes are employed to select from competing stimuli following internal goals. In this, the demands for the recruitment of top-down control processes depend on the…

A Dynamic Process Model for Optimizing the Hospital Environment Cash-Flow

NASA Astrophysics Data System (ADS)

Pater, Flavius; Rosu, Serban

2011-09-01

In this article is presented a new approach to some fundamental techniques of solving dynamic programming problems with the use of functional equations. We will analyze the problem of minimizing the cost of treatment in a hospital environment. Mathematical modeling of this process leads to an optimal control problem with a finite horizon.

An intelligent CNC machine control system architecture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, D.J.; Loucks, C.S.

1996-10-01

Intelligent, agile manufacturing relies on automated programming of digitally controlled processes. Currently, processes such as Computer Numerically Controlled (CNC) machining are difficult to automate because of highly restrictive controllers and poor software environments. It is also difficult to utilize sensors and process models for adaptive control, or to integrate machining processes with other tasks within a factory floor setting. As part of a Laboratory Directed Research and Development (LDRD) program, a CNC machine control system architecture based on object-oriented design and graphical programming has been developed to address some of these problems and to demonstrate automated agile machining applications usingmore » platform-independent software.« less

Construction of integrated case environments.

PubMed

Losavio, Francisca; Matteo, Alfredo; Pérez, María

2003-01-01

The main goal of Computer-Aided Software Engineering (CASE) technology is to improve the entire software system development process. The CASE approach is not merely a technology; it involves a fundamental change in the process of software development. The tendency of the CASE approach, technically speaking, is the integration of tools that assist in the application of specific methods. In this sense, the environment architecture, which includes the platform and the system's hardware and software, constitutes the base of the CASE environment. The problem of tools integration has been proposed for two decades. Current integration efforts emphasize the interoperability of tools, especially in distributed environments. In this work we use the Brown approach. The environment resulting from the application of this model is called a federative environment, focusing on the fact that this architecture pays special attention to the connections among the components of the environment. This approach is now being used in component-based design. This paper describes a concrete experience in civil engineering and architecture fields, for the construction of an integrated CASE environment. A generic architectural framework based on an intermediary architectural pattern is applied to achieve the integration of the different tools. This intermediary represents the control perspective of the PAC (Presentation-Abstraction-Control) style, which has been implemented as a Mediator pattern and it has been used in the interactive systems domain. In addition, a process is given to construct the integrated CASE.

The use of information theory in evolutionary biology.

PubMed

Adami, Christoph

2012-05-01

Information is a key concept in evolutionary biology. Information stored in a biological organism's genome is used to generate the organism and to maintain and control it. Information is also that which evolves. When a population adapts to a local environment, information about this environment is fixed in a representative genome. However, when an environment changes, information can be lost. At the same time, information is processed by animal brains to survive in complex environments, and the capacity for information processing also evolves. Here, I review applications of information theory to the evolution of proteins and to the evolution of information processing in simulated agents that adapt to perform a complex task. © 2012 New York Academy of Sciences.

Integration of domain and resource-based reasoning for real-time control in dynamic environments

NASA Technical Reports Server (NTRS)

Morgan, Keith; Whitebread, Kenneth R.; Kendus, Michael; Cromarty, Andrew S.

1993-01-01

A real-time software controller that successfully integrates domain-based and resource-based control reasoning to perform task execution in a dynamically changing environment is described. The design of the controller is based on the concept of partitioning the process to be controlled into a set of tasks, each of which achieves some process goal. It is assumed that, in general, there are multiple ways (tasks) to achieve a goal. The controller dynamically determines current goals and their current criticality, choosing and scheduling tasks to achieve those goals in the time available. It incorporates rule-based goal reasoning, a TMS-based criticality propagation mechanism, and a real-time scheduler. The controller has been used to build a knowledge-based situation assessment system that formed a major component of a real-time, distributed, cooperative problem solving system built under DARPA contract. It is also being employed in other applications now in progress.

A real time, FEM based optimal control algorithm and its implementation using parallel processing hardware (transistors) in a microprocessor environment

NASA Technical Reports Server (NTRS)

Patten, William Neff

1989-01-01

There is an evident need to discover a means of establishing reliable, implementable controls for systems that are plagued by nonlinear and, or uncertain, model dynamics. The development of a generic controller design tool for tough-to-control systems is reported. The method utilizes a moving grid, time infinite element based solution of the necessary conditions that describe an optimal controller for a system. The technique produces a discrete feedback controller. Real time laboratory experiments are now being conducted to demonstrate the viability of the method. The algorithm that results is being implemented in a microprocessor environment. Critical computational tasks are accomplished using a low cost, on-board, multiprocessor (INMOS T800 Transputers) and parallel processing. Progress to date validates the methodology presented. Applications of the technique to the control of highly flexible robotic appendages are suggested.

A Distributed Control System Prototyping Environment to Support Control Room Modernization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lew, Roger Thomas; Boring, Ronald Laurids; Ulrich, Thomas Anthony

Operators of critical processes, such as nuclear power production, must contend with highly complex systems, procedures, and regulations. Developing human-machine interfaces (HMIs) that better support operators is a high priority for ensuring the safe and reliable operation of critical processes. Human factors engineering (HFE) provides a rich and mature set of tools for evaluating the performance of HMIs, however the set of tools for developing and designing HMIs is still in its infancy. Here we propose a rapid prototyping approach for integrating proposed HMIs into their native environments before a design is finalized. This approach allows researchers and developers tomore » test design ideas and eliminate design flaws prior to fully developing the new system. We illustrate this approach with four prototype designs developed using Microsoft’s Windows Presentation Foundation (WPF). One example is integrated into a microworld environment to test the functionality of the design and identify the optimal level of automation for a new system in a nuclear power plant. The other three examples are integrated into a full-scale, glasstop digital simulator of a nuclear power plant. One example demonstrates the capabilities of next generation control concepts; another aims to expand the current state of the art; lastly, an HMI prototype was developed as a test platform for a new control system currently in development at U.S. nuclear power plants. WPF possesses several characteristics that make it well suited to HMI design. It provides a tremendous amount of flexibility, agility, robustness, and extensibility. Distributed control system (DCS) specific environments tend to focus on the safety and reliability requirements for real-world interfaces and consequently have less emphasis on providing functionality to support novel interaction paradigms. Because of WPF’s large user-base, Microsoft can provide an extremely mature tool. Within process control applications,WPF is platform independent and can communicate with popular full-scope process control simulator vendor plant models and DCS platforms.« less

Controlled environment crop production - Hydroponic vs. lunar regolith

NASA Technical Reports Server (NTRS)

Bugbee, Bruce G.; Salisbury, Frank B.

1989-01-01

The potential of controlled environment crop production in a lunar colony is discussed. Findings on the effects of optimal root-zone and aerial environments derived as part of the NASA CELSS project at Utah State are presented. The concept of growing wheat in optimal environment is discussed. It is suggested that genetic engineering might produce the ideal wheat cultivar for CELSS (about 100 mm in height with fewer leaves). The Utah State University hydroponic system is outlined and diagrams of the system and plant container construction are provided. Ratio of plant mass to solution mass, minimum root-zone volume, maintenance, and pH control are discussed. A comparison of liquid hydrophonic systems and lunar regoliths as substrates for plant growth is provided. The physiological processes that are affected by the root-zone environment are discussed including carbon partitioning, nutrient availability, nutrient absorption zones, root-zone oxygen, plant water potential, root-produced hormones, and rhizosphere pH control.

RCTS: A flexible environment for sensor integration and control of robot systems; the distributed processing approach

NASA Technical Reports Server (NTRS)

Allard, R.; Mack, B.; Bayoumi, M. M.

1989-01-01

Most robot systems lack a suitable hardware and software environment for the efficient research of new control and sensing schemes. Typically, engineers and researchers need to be experts in control, sensing, programming, communication and robotics in order to implement, integrate and test new ideas in a robot system. In order to reduce this time, the Robot Controller Test Station (RCTS) has been developed. It uses a modular hardware and software architecture allowing easy physical and functional reconfiguration of a robot. This is accomplished by emphasizing four major design goals: flexibility, portability, ease of use, and ease of modification. An enhanced distributed processing version of RCTS is described. It features an expanded and more flexible communication system design. Distributed processing results in the availability of more local computing power and retains the low cost of microprocessors. A large number of possible communication, control and sensing schemes can therefore be easily introduced and tested, using the same basic software structure.

Autoplan: A self-processing network model for an extended blocks world planning environment

NASA Technical Reports Server (NTRS)

Dautrechy, C. Lynne; Reggia, James A.; Mcfadden, Frank

1990-01-01

Self-processing network models (neural/connectionist models, marker passing/message passing networks, etc.) are currently undergoing intense investigation for a variety of information processing applications. These models are potentially very powerful in that they support a large amount of explicit parallel processing, and they cleanly integrate high level and low level information processing. However they are currently limited by a lack of understanding of how to apply them effectively in many application areas. The formulation of self-processing network methods for dynamic, reactive planning is studied. The long-term goal is to formulate robust, computationally effective information processing methods for the distributed control of semiautonomous exploration systems, e.g., the Mars Rover. The current research effort is focusing on hierarchical plan generation, execution and revision through local operations in an extended blocks world environment. This scenario involves many challenging features that would be encountered in a real planning and control environment: multiple simultaneous goals, parallel as well as sequential action execution, action sequencing determined not only by goals and their interactions but also by limited resources (e.g., three tasks, two acting agents), need to interpret unanticipated events and react appropriately through replanning, etc.

40 CFR 408.207 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... control technology. 408.207 Section 408.207 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... degree of effluent reduction attainable by the application of the best conventional pollutant control... processing facility located in population or processing centers including but not limited to Anchorage...

40 CFR 408.207 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... control technology. 408.207 Section 408.207 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... degree of effluent reduction attainable by the application of the best conventional pollutant control... processing facility located in population or processing centers including but not limited to Anchorage...

40 CFR 408.207 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... control technology. 408.207 Section 408.207 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... degree of effluent reduction attainable by the application of the best conventional pollutant control... processing facility located in population or processing centers including but not limited to Anchorage...

40 CFR 408.207 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... control technology. 408.207 Section 408.207 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... degree of effluent reduction attainable by the application of the best conventional pollutant control... processing facility located in population or processing centers including but not limited to Anchorage...

40 CFR 408.207 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... control technology. 408.207 Section 408.207 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... degree of effluent reduction attainable by the application of the best conventional pollutant control... processing facility located in population or processing centers including but not limited to Anchorage...

Process for guidance, containment, treatment, and imaging in a subsurface environment utilizing ferro-fluids

DOEpatents

Moridis, George J.; Oldenburg, Curtis M.

2001-01-01

Disclosed are processes for monitoring and control of underground contamination, which involve the application of ferrofluids. Two broad uses of ferrofluids are described: (1) to control liquid movement by the application of strong external magnetic fields; and (2) to image liquids by standard geophysical methods.

Development of a Low-Latency, High Data Rate, Differential GPS Relative Positioning System for UAV Formation Flight Control

DTIC Science & Technology

2006-09-01

spiral development cycle involved transporting the software processes from a Windows XP / MATLAB environment to a Linux / C++ environment. This...tested on. Additionally, in the case of the GUMSTIX PC boards, the LINUX operating system is burned into the read-only memory. Lastly, both PC-104 and...both the real-time environment and the post-processed en - vironment. When the system operates in real-time mode, an output file is generated which

Application of the Modular Command and Control Evaluation Structure to a Strategic Defense Initiative Command and Control System.

DTIC Science & Technology

1987-03-01

environment . Actions within the process loop is initiated by a perceived divergence from a desired state and the sensed environmental state. Definitions of the...initiated environmental effect. An action by our own forces as well as by the enemy forces can create an alteration to the overall environment . The DESIRED...Additionally, the model would accommodate the entire C2 system, including physical entities, structure, and its environment . The objective was to

PILOT: An intelligent distributed operations support system

NASA Technical Reports Server (NTRS)

Rasmussen, Arthur N.

1993-01-01

The Real-Time Data System (RTDS) project is exploring the application of advanced technologies to the real-time flight operations environment of the Mission Control Centers at NASA's Johnson Space Center. The system, based on a network of engineering workstations, provides services such as delivery of real time telemetry data to flight control applications. To automate the operation of this complex distributed environment, a facility called PILOT (Process Integrity Level and Operation Tracker) is being developed. PILOT comprises a set of distributed agents cooperating with a rule-based expert system; together they monitor process operation and data flows throughout the RTDS network. The goal of PILOT is to provide unattended management and automated operation under user control.

Sire: An Automated Software Development Environment.

DTIC Science & Technology

1983-12-01

understanding the fundamental nature of the software process" (Osterweil, 1981: 35). In fact, the optimal environment for most applications is found by extending... resource planning and other management concerns that cause these problems. Therefore, a complete ASDE should attempt to provide the -21...management with some type of control over the project without impeding the actual development process. Facilities that estimate current resource

Simulation Environment Synchronizing Real Equipment for Manufacturing Cell

NASA Astrophysics Data System (ADS)

Inukai, Toshihiro; Hibino, Hironori; Fukuda, Yoshiro

Recently, manufacturing industries face various problems such as shorter product life cycle, more diversified customer needs. In this situation, it is very important to reduce lead-time of manufacturing system constructions. At the manufacturing system implementation stage, it is important to make and evaluate facility control programs for a manufacturing cell, such as ladder programs for programmable logical controllers (PLCs) rapidly. However, before the manufacturing systems are implemented, methods to evaluate the facility control programs for the equipment while mixing and synchronizing real equipment and virtual factory models on the computers have not been developed. This difficulty is caused by the complexity of the manufacturing system composed of a great variety of equipment, and stopped precise and rapid support of a manufacturing engineering process. In this paper, a manufacturing engineering environment (MEE) to support manufacturing engineering processes using simulation technologies is proposed. MEE consists of a manufacturing cell simulation environment (MCSE) and a distributed simulation environment (DSE). MCSE, which consists of a manufacturing cell simulator and a soft-wiring system, is emphatically proposed in detail. MCSE realizes making and evaluating facility control programs by using virtual factory models on computers before manufacturing systems are implemented.

Graphical user interface for image acquisition and processing

DOEpatents

Goldberg, Kenneth A.

2002-01-01

An event-driven GUI-based image acquisition interface for the IDL programming environment designed for CCD camera control and image acquisition directly into the IDL environment where image manipulation and data analysis can be performed, and a toolbox of real-time analysis applications. Running the image acquisition hardware directly from IDL removes the necessity of first saving images in one program and then importing the data into IDL for analysis in a second step. Bringing the data directly into IDL creates an opportunity for the implementation of IDL image processing and display functions in real-time. program allows control over the available charge coupled device (CCD) detector parameters, data acquisition, file saving and loading, and image manipulation and processing, all from within IDL. The program is built using IDL's widget libraries to control the on-screen display and user interface.

Software development environments: Status and trends

NASA Technical Reports Server (NTRS)

Duffel, Larry E.

1988-01-01

Currently software engineers are the essential integrating factors tying several components together. The components consist of process, methods, computers, tools, support environments, and software engineers. The engineers today empower the tools versus the tools empowering the engineers. Some of the issues in software engineering are quality, managing the software engineering process, and productivity. A strategy to accomplish this is to promote the evolution of software engineering from an ad hoc, labor intensive activity to a managed, technology supported discipline. This strategy may be implemented by putting the process under management control, adopting appropriate methods, inserting the technology that provides automated support for the process and methods, collecting automated tools into an integrated environment and educating the personnel.

CHIMERA II - A real-time multiprocessing environment for sensor-based robot control

NASA Technical Reports Server (NTRS)

Stewart, David B.; Schmitz, Donald E.; Khosla, Pradeep K.

1989-01-01

A multiprocessing environment for a wide variety of sensor-based robot system, providing the flexibility, performance, and UNIX-compatible interface needed for fast development of real-time code is addressed. The requirements imposed on the design of a programming environment for sensor-based robotic control is outlined. The details of the current hardware configuration are presented, along with the details of the CHIMERA II software. Emphasis is placed on the kernel, low-level interboard communication, user interface, extended file system, user-definable and dynamically selectable real-time schedulers, remote process synchronization, and generalized interprocess communication. A possible implementation of a hierarchical control model, the NASA/NBS standard reference model for telerobot control system is demonstrated.

Wireless Sensor Network-Based Greenhouse Environment Monitoring and Automatic Control System for Dew Condensation Prevention

PubMed Central

Park, Dae-Heon; Park, Jang-Woo

2011-01-01

Dew condensation on the leaf surface of greenhouse crops can promote diseases caused by fungus and bacteria, affecting the growth of the crops. In this paper, we present a WSN (Wireless Sensor Network)-based automatic monitoring system to prevent dew condensation in a greenhouse environment. The system is composed of sensor nodes for collecting data, base nodes for processing collected data, relay nodes for driving devices for adjusting the environment inside greenhouse and an environment server for data storage and processing. Using the Barenbrug formula for calculating the dew point on the leaves, this system is realized to prevent dew condensation phenomena on the crop’s surface acting as an important element for prevention of diseases infections. We also constructed a physical model resembling the typical greenhouse in order to verify the performance of our system with regard to dew condensation control. PMID:22163813

Wireless sensor network-based greenhouse environment monitoring and automatic control system for dew condensation prevention.

PubMed

Park, Dae-Heon; Park, Jang-Woo

2011-01-01

Dew condensation on the leaf surface of greenhouse crops can promote diseases caused by fungus and bacteria, affecting the growth of the crops. In this paper, we present a WSN (Wireless Sensor Network)-based automatic monitoring system to prevent dew condensation in a greenhouse environment. The system is composed of sensor nodes for collecting data, base nodes for processing collected data, relay nodes for driving devices for adjusting the environment inside greenhouse and an environment server for data storage and processing. Using the Barenbrug formula for calculating the dew point on the leaves, this system is realized to prevent dew condensation phenomena on the crop's surface acting as an important element for prevention of diseases infections. We also constructed a physical model resembling the typical greenhouse in order to verify the performance of our system with regard to dew condensation control.

Digital Signal Processing and Control for the Study of Gene Networks

NASA Astrophysics Data System (ADS)

Shin, Yong-Jun

2016-04-01

Thanks to the digital revolution, digital signal processing and control has been widely used in many areas of science and engineering today. It provides practical and powerful tools to model, simulate, analyze, design, measure, and control complex and dynamic systems such as robots and aircrafts. Gene networks are also complex dynamic systems which can be studied via digital signal processing and control. Unlike conventional computational methods, this approach is capable of not only modeling but also controlling gene networks since the experimental environment is mostly digital today. The overall aim of this article is to introduce digital signal processing and control as a useful tool for the study of gene networks.

Digital Signal Processing and Control for the Study of Gene Networks.

PubMed

Shin, Yong-Jun

2016-04-22

Thanks to the digital revolution, digital signal processing and control has been widely used in many areas of science and engineering today. It provides practical and powerful tools to model, simulate, analyze, design, measure, and control complex and dynamic systems such as robots and aircrafts. Gene networks are also complex dynamic systems which can be studied via digital signal processing and control. Unlike conventional computational methods, this approach is capable of not only modeling but also controlling gene networks since the experimental environment is mostly digital today. The overall aim of this article is to introduce digital signal processing and control as a useful tool for the study of gene networks.

Digital Signal Processing and Control for the Study of Gene Networks

PubMed Central

Shin, Yong-Jun

2016-01-01

Thanks to the digital revolution, digital signal processing and control has been widely used in many areas of science and engineering today. It provides practical and powerful tools to model, simulate, analyze, design, measure, and control complex and dynamic systems such as robots and aircrafts. Gene networks are also complex dynamic systems which can be studied via digital signal processing and control. Unlike conventional computational methods, this approach is capable of not only modeling but also controlling gene networks since the experimental environment is mostly digital today. The overall aim of this article is to introduce digital signal processing and control as a useful tool for the study of gene networks. PMID:27102828

Optimized pulses for the control of uncertain qubits

DOE PAGES

Grace, Matthew D.; Dominy, Jason M.; Witzel, Wayne M.; ...

2012-05-18

The construction of high-fidelity control fields that are robust to control, system, and/or surrounding environment uncertainties is a crucial objective for quantum information processing. Using the two-state Landau-Zener model for illustrative simulations of a controlled qubit, we generate optimal controls for π/2 and π pulses and investigate their inherent robustness to uncertainty in the magnitude of the drift Hamiltonian. Next, we construct a quantum-control protocol to improve system-drift robustness by combining environment-decoupling pulse criteria and optimal control theory for unitary operations. By perturbatively expanding the unitary time-evolution operator for an open quantum system, previous analysis of environment-decoupling control pulses hasmore » calculated explicit control-field criteria to suppress environment-induced errors up to (but not including) third order from π/2 and π pulses. We systematically integrate this criteria with optimal control theory, incorporating an estimate of the uncertain parameter to produce improvements in gate fidelity and robustness, demonstrated via a numerical example based on double quantum dot qubits. For the qubit model used in this work, postfacto analysis of the resulting controls suggests that realistic control-field fluctuations and noise may contribute just as significantly to gate errors as system and environment fluctuations.« less

COMPLEX CONDITIONAL CONTROL BY PIGEONS IN A CONTINUOUS VIRTUAL ENVIRONMENT

PubMed Central

Qadri, Muhammad A. J.; Reid, Sean; Cook, Robert G.

2016-01-01

We tested two pigeons in a continuously streaming digital environment. Using animation software that constantly presented a dynamic, three-dimensional (3D) environment, the animals were tested with a conditional object identification task. The correct object at a given time depended on the virtual context currently streaming in front of the pigeon. Pigeons were required to accurately peck correct target objects in the environment for food reward, while suppressing any pecks to intermixed distractor objects which delayed the next object’s presentation. Experiment 1 established that the pigeons’ discrimination of two objects could be controlled by the surface material of the digital terrain. Experiment 2 established that the pigeons’ discrimination of four objects could be conjunctively controlled by both the surface material and topography of the streaming environment. These experiments indicate that pigeons can simultaneously process and use at least two context cues from a streaming environment to control their identification behavior of passing objects. These results add to the promise of testing interactive digital environments with animals to advance our understanding of cognition and behavior. PMID:26781058

Examining Metacognitive Processes in Exploratory Computer-Based Learning Environments Using Activity Log Analysis

ERIC Educational Resources Information Center

Chang, Yoo Kyung

2010-01-01

Metacognition is widely studied for its influence on the effectiveness of learning. With Exploratory Computer-Based Learning Environments (ECBLE), metacognition is found to be especially important because these environments require adaptive metacognitive control by the learners due to their open-ended structure that allows for multiple learning…

Quantum coherence and entanglement control for atom-cavity systems

NASA Astrophysics Data System (ADS)

Shu, Wenchong

Coherence and entanglement play a significant role in the quantum theory. Ideal quantum systems, "closed" to the outside world, remain quantum forever and thus manage to retain coherence and entanglement. Real quantum systems, however, are open to the environment and are therefore susceptible to the phenomenon of decoherence and disentanglement which are major hindrances to the effectiveness of quantum information processing tasks. In this thesis we have theoretically studied the evolution of coherence and entanglement in quantum systems coupled to various environments. We have also studied ways and means of controlling the decay of coherence and entanglement. We have studied the exact qubit entanglement dynamics of some interesting initial states coupled to a high-Q cavity containing zero photon, one photon, two photons and many photons respectively. We have found that an initially correlated environmental state can serve as an enhancer for entanglement decay or generation processes. More precisely, we have demonstrated that the degree of entanglement, including its collapse as well as its revival times, can be significantly modified by the correlated structure of the environmental modes. We have also studied dynamical decoupling (DD) technique --- a prominent strategy of controlling decoherence and preserving entanglement in open quantum systems. We have analyzed several DD control methods applied to qubit systems that can eliminate the system-environment coupling and prolong the quantum coherence time. Particularly, we have proposed a new DD sequence consisting a set of designed control operators that can universally protected an unknown qutrit state against colored phase and amplitude environment noises. In addition, in a non-Markovian regime, we have reformulated the quantum state diffusion (QSD) equation to incorporate the effect of the external control fields. Without any assumptions on the system-environment coupling and the size of environment, we have consistently solved the control dynamics of open quantum systems using this stochastic QSD approach. By implementing the QSD equation, our numerical results have revealed that how the control efficacy depends on the designed time points and shapes of the applied control pulses, and the environment memory time scale.

40 CFR 60.381 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... control device. Control device means the air pollution control equipment used to reduce particulate matter... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Metallic Mineral Processing Plants § 60...

40 CFR 60.381 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... control device. Control device means the air pollution control equipment used to reduce particulate matter... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Metallic Mineral Processing Plants § 60...

40 CFR 60.381 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... control device. Control device means the air pollution control equipment used to reduce particulate matter... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Metallic Mineral Processing Plants § 60...

40 CFR 60.381 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... control device. Control device means the air pollution control equipment used to reduce particulate matter... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Metallic Mineral Processing Plants § 60...

40 CFR 60.381 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... control device. Control device means the air pollution control equipment used to reduce particulate matter... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Metallic Mineral Processing Plants § 60...

Multi-Core Processors: An Enabling Technology for Embedded Distributed Model-Based Control (Postprint)

DTIC Science & Technology

2008-07-01

generation of process partitioning, a thread pipelining becomes possible. In this paper we briefly summarize the requirements and trends for FADEC based... FADEC environment, presenting a hypothetical realization of an example application. Finally we discuss the application of Time-Triggered...based control applications of the future. 15. SUBJECT TERMS Gas turbine, FADEC , Multi-core processing technology, disturbed based control

40 CFR 761.363 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Applicability. 761.363 Section 761.363 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT POLYCHLORINATED BIPHENYLS (PCBs) MANUFACTURING, PROCESSING, DISTRIBUTION IN COMMERCE, AND USE PROHIBITIONS Double...

40 CFR 761.360 - Background.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Background. 761.360 Section 761.360 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT POLYCHLORINATED BIPHENYLS (PCBs) MANUFACTURING, PROCESSING, DISTRIBUTION IN COMMERCE, AND USE PROHIBITIONS Double...

40 CFR 761.320 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Applicability. 761.320 Section 761.320 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT POLYCHLORINATED BIPHENYLS (PCBs) MANUFACTURING, PROCESSING, DISTRIBUTION IN COMMERCE, AND USE PROHIBITIONS Self...

40 CFR 85.2233 - Steady state test equipment calibrations, adjustments, and quality control-EPA 91.

Code of Federal Regulations, 2010 CFR

2010-07-01

... compensated for automatically and statistical process control demonstrates equal or better quality control... calibrations, adjustments, and quality control-EPA 91. 85.2233 Section 85.2233 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE...

40 CFR 63.10001 - Affirmative defense for exceedence of emission limit during malfunction.

Code of Federal Regulations, 2013 CFR

2013-07-01

... unavoidable failure of air pollution control and monitoring equipment, process equipment, or a process to..., proper design or better operation and maintenance practices; and (iii) Did not stem from any activity or... ambient air quality, the environment and human health; and (6) All emissions monitoring and control...

40 CFR 408.167 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... control technology. 408.167 Section 408.167 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... control technology. (a) [Reserved] (b) Except as provided in §§ 125.30 through 125.32, any hand-butchered salmon processing facility located in population or processing centers including but not limited to...

40 CFR 408.167 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... control technology. 408.167 Section 408.167 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... control technology. (a) [Reserved] (b) Except as provided in §§ 125.30 through 125.32, any hand-butchered salmon processing facility located in population or processing centers including but not limited to...

40 CFR 408.167 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... control technology. 408.167 Section 408.167 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... control technology. (a) [Reserved] (b) Except as provided in §§ 125.30 through 125.32, any hand-butchered salmon processing facility located in population or processing centers including but not limited to...

MULTI-SCALE CONTROLS ON AND CONSEQUENCES OF AEOLIAN PROCESSES IN LANDSCAPE CHANGE IN ARID AND SEMI-ARID ENVIRONMENTS

EPA Science Inventory

This paper reviews the controls on aeolian processes and their consequences at plant-interspace, patch-landscape, and regional-global scales. Based on this review, we define the requirements for a cross-scale model of wind erosion in structurally complex arid and semiarid ecosyst...

Process-based quality for thermal spray via feedback control

NASA Astrophysics Data System (ADS)

Dykhuizen, R. C.; Neiser, R. A.

2006-09-01

Quality control of a thermal spray system manufacturing process is difficult due to the many input variables that need to be controlled. Great care must be taken to ensure that the process remains constant to obtain a consistent quality of the parts. Control is greatly complicated by the fact that measurement of particle velocities and temperatures is a noisy stochastic process. This article illustrates the application of quality control concepts to a wire flame spray process. A central feature of the real-time control system is an automatic feedback control scheme that provides fine adjustments to ensure that uncontrolled variations are accommodated. It is shown how the control vectors can be constructed from simple process maps to independently control particle velocity and temperature. This control scheme is shown to perform well in a real production environment. We also demonstrate that slight variations in the feed wire curvature can greatly influence the process. Finally, the geometry of the spray system and sensor must remain constant for the best reproducibility.

40 CFR 65.115 - Standards: Closed vent systems and control devices; or emissions routed to a fuel gas system or...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Standards: Closed vent systems and control devices; or emissions routed to a fuel gas system or process. 65.115 Section 65.115 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONSOLIDATED FEDERAL AIR RULE Equipment Leaks § 65.115 Standards:...

40 CFR 65.62 - Process vent group determination.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., or Group 2B) for each process vent. Group 1 process vents require control, and Group 2A and 2B... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Process vent group determination. 65... (CONTINUED) CONSOLIDATED FEDERAL AIR RULE Process Vents § 65.62 Process vent group determination. (a) Group...

21 CFR 123.6 - Hazard analysis and Hazard Analysis Critical Control Point (HACCP) plan.

Code of Federal Regulations, 2013 CFR

2013-04-01

... identified food safety hazards, including as appropriate: (i) Critical control points designed to control... control points designed to control food safety hazards introduced outside the processing plant environment... Control Point (HACCP) plan. 123.6 Section 123.6 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF...

21 CFR 123.6 - Hazard analysis and Hazard Analysis Critical Control Point (HACCP) plan.

Code of Federal Regulations, 2011 CFR

2011-04-01

... identified food safety hazards, including as appropriate: (i) Critical control points designed to control... control points designed to control food safety hazards introduced outside the processing plant environment... Control Point (HACCP) plan. 123.6 Section 123.6 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF...

21 CFR 123.6 - Hazard analysis and Hazard Analysis Critical Control Point (HACCP) plan.

Code of Federal Regulations, 2014 CFR

2014-04-01

... identified food safety hazards, including as appropriate: (i) Critical control points designed to control... control points designed to control food safety hazards introduced outside the processing plant environment... Control Point (HACCP) plan. 123.6 Section 123.6 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF...

Contamination control and cleanliness level integrity for the Space Shuttle Orbiter PLB, payloads and facilities at KSC

NASA Technical Reports Server (NTRS)

Bartelson, D.

1984-01-01

The PLB, its cargo, and payload canister must satisfy the cleanliness requirements of visual clean (VC) level 1, 2, 3, or special as stated in NASA document SN-C-0005A. The specific level of cleanliness is chosen by the payload bay customer for their mission. During orbiter turnaround processing at KSC, the payload bay is exposed to the environments of the Orbiter Processing Facility (OPF) and the Payload Changeout Room (PCR). In supportive response to the orbiter payload bay/facility interface, it is necessary that the facility environment be controlled and monitored to protect the cleanliness/environmental integrity of the payload bay and its cargo. Techniques used to meet environmental requirements during orbiter processing are introduced.

Shift changes, updates, and the on-call architecture in space shuttle mission control.

PubMed

Patterson, E S; Woods, D D

2001-01-01

In domains such as nuclear power, industrial process control, and space shuttle mission control, there is increased interest in reducing personnel during nominal operations. An essential element in maintaining safe operations in high risk environments with this 'on-call' organizational architecture is to understand how to bring called-in practitioners up to speed quickly during escalating situations. Targeted field observations were conducted to investigate what it means to update a supervisory controller on the status of a continuous, anomaly-driven process in a complex, distributed environment. Sixteen shift changes, or handovers, at the NASA Johnson Space Center were observed during the STS-76 Space Shuttle mission. The findings from this observational study highlight the importance of prior knowledge in the updates and demonstrate how missing updates can leave flight controllers vulnerable to being unprepared. Implications for mitigating risk in the transition to 'on-call' architectures are discussed.

Shift changes, updates, and the on-call architecture in space shuttle mission control

NASA Technical Reports Server (NTRS)

Patterson, E. S.; Woods, D. D.

2001-01-01

In domains such as nuclear power, industrial process control, and space shuttle mission control, there is increased interest in reducing personnel during nominal operations. An essential element in maintaining safe operations in high risk environments with this 'on-call' organizational architecture is to understand how to bring called-in practitioners up to speed quickly during escalating situations. Targeted field observations were conducted to investigate what it means to update a supervisory controller on the status of a continuous, anomaly-driven process in a complex, distributed environment. Sixteen shift changes, or handovers, at the NASA Johnson Space Center were observed during the STS-76 Space Shuttle mission. The findings from this observational study highlight the importance of prior knowledge in the updates and demonstrate how missing updates can leave flight controllers vulnerable to being unprepared. Implications for mitigating risk in the transition to 'on-call' architectures are discussed.

Distributed systems status and control

NASA Technical Reports Server (NTRS)

Kreidler, David; Vickers, David

1990-01-01

Concepts are investigated for an automated status and control system for a distributed processing environment. System characteristics, data requirements for health assessment, data acquisition methods, system diagnosis methods and control methods were investigated in an attempt to determine the high-level requirements for a system which can be used to assess the health of a distributed processing system and implement control procedures to maintain an accepted level of health for the system. A potential concept for automated status and control includes the use of expert system techniques to assess the health of the system, detect and diagnose faults, and initiate or recommend actions to correct the faults. Therefore, this research included the investigation of methods by which expert systems were developed for real-time environments and distributed systems. The focus is on the features required by real-time expert systems and the tools available to develop real-time expert systems.

40 CFR 35.712 - Competitive process.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Competitive process. 35.712 Section 35... Monitoring (section 28) § 35.712 Competitive process. EPA will award Toxic Substances Control Act Compliance Monitoring grants to Tribes or Intertribal Consortia through a competitive process in accordance with...

40 CFR 763.176 - Inspections.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Inspections. 763.176 Section 763.176 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Prohibition of the Manufacture, Importation, Processing, and Distribution in Commerce of Certain Asbestos...

40 CFR 763.178 - Recordkeeping.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Recordkeeping. 763.178 Section 763.178 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Prohibition of the Manufacture, Importation, Processing, and Distribution in Commerce of Certain Asbestos...

40 CFR 761.372 - Specific requirements for relatively clean surfaces.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Specific requirements for relatively clean surfaces. 761.372 Section 761.372 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT POLYCHLORINATED BIPHENYLS (PCBs) MANUFACTURING, PROCESSING...

40 CFR 761.93 - Import for disposal.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Import for disposal. 761.93 Section 761.93 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT POLYCHLORINATED BIPHENYLS (PCBs) MANUFACTURING, PROCESSING, DISTRIBUTION IN COMMERCE, AND USE...

40 CFR 761.366 - Cleanup equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Cleanup equipment. 761.366 Section 761.366 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT POLYCHLORINATED BIPHENYLS (PCBs) MANUFACTURING, PROCESSING, DISTRIBUTION IN COMMERCE, AND USE PROHIBITIONS Double...

40 CFR 725.70 - Compliance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Compliance. 725.70 Section 725.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Administrative Procedures § 725.70 Compliance. (a) Failure...

40 CFR 725.70 - Compliance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Compliance. 725.70 Section 725.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Administrative Procedures § 725.70 Compliance. (a) Failure...

Personal Learning Environments in the Workplace: An Exploratory Study into the Key Business Decision Factors

ERIC Educational Resources Information Center

Chatterjee, Arunangsu; Law, Effie Lai-Chong; Mikroyannidis, Alexander; Owen, Glyn; Velasco, Karen

2013-01-01

Personal Learning Environments (PLEs) have emerged as a solution to the need of learners for open and easily customisable learning environments. PLEs essentially hand complete control over the learning process to the learner. However, this learning model is not fully compatible with learning in the workplace, which is influenced by certain…

Regularity in an environment produces an internal torque pattern for biped balance control.

PubMed

Ito, Satoshi; Kawasaki, Haruhisa

2005-04-01

In this paper, we present a control method for achieving biped static balance under unknown periodic external forces whose periods are only known. In order to maintain static balance adaptively in an uncertain environment, it is essential to have information on the ground reaction forces. However, when the biped is exposed to a steady environment that provides an external force periodically, uncertain factors on the regularity with respect to a steady environment are gradually clarified using learning process, and finally a torque pattern for balancing motion is acquired. Consequently, static balance is maintained without feedback from ground reaction forces and achieved in a feedforward manner.

40 CFR 420.08 - Non-process wastewater and storm water.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 30 2012-07-01 2012-07-01 false Non-process wastewater and storm water...-process wastewater and storm water. Permit and pretreatment control authorities may provide for increased loadings for non-process wastewaters defined at § 420.02 and for storm water from the immediate process...

40 CFR 420.08 - Non-process wastewater and storm water.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true Non-process wastewater and storm water...-process wastewater and storm water. Permit and pretreatment control authorities may provide for increased loadings for non-process wastewaters defined at § 420.02 and for storm water from the immediate process...

40 CFR 420.08 - Non-process wastewater and storm water.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Non-process wastewater and storm water...-process wastewater and storm water. Permit and pretreatment control authorities may provide for increased loadings for non-process wastewaters defined at § 420.02 and for storm water from the immediate process...

40 CFR 420.08 - Non-process wastewater and storm water.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 29 2014-07-01 2012-07-01 true Non-process wastewater and storm water...-process wastewater and storm water. Permit and pretreatment control authorities may provide for increased loadings for non-process wastewaters defined at § 420.02 and for storm water from the immediate process...

40 CFR 420.08 - Non-process wastewater and storm water.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Non-process wastewater and storm water...-process wastewater and storm water. Permit and pretreatment control authorities may provide for increased loadings for non-process wastewaters defined at § 420.02 and for storm water from the immediate process...

21 CFR 120.8 - Hazard Analysis and Critical Control Point (HACCP) plan.

Code of Federal Regulations, 2010 CFR

2010-04-01

...: (i) Critical control points designed to control food hazards that are reasonably likely to occur and could be introduced inside the processing plant environment; and (ii) Critical control points designed... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Hazard Analysis and Critical Control Point (HACCP...

21 CFR 120.8 - Hazard Analysis and Critical Control Point (HACCP) plan.

Code of Federal Regulations, 2012 CFR

2012-04-01

...: (i) Critical control points designed to control food hazards that are reasonably likely to occur and could be introduced inside the processing plant environment; and (ii) Critical control points designed... 21 Food and Drugs 2 2012-04-01 2012-04-01 false Hazard Analysis and Critical Control Point (HACCP...

21 CFR 120.8 - Hazard Analysis and Critical Control Point (HACCP) plan.

Code of Federal Regulations, 2013 CFR

2013-04-01

...: (i) Critical control points designed to control food hazards that are reasonably likely to occur and could be introduced inside the processing plant environment; and (ii) Critical control points designed... 21 Food and Drugs 2 2013-04-01 2013-04-01 false Hazard Analysis and Critical Control Point (HACCP...

21 CFR 120.8 - Hazard Analysis and Critical Control Point (HACCP) plan.

Code of Federal Regulations, 2014 CFR

2014-04-01

...: (i) Critical control points designed to control food hazards that are reasonably likely to occur and could be introduced inside the processing plant environment; and (ii) Critical control points designed... 21 Food and Drugs 2 2014-04-01 2014-04-01 false Hazard Analysis and Critical Control Point (HACCP...

40 CFR 65.152 - Carbon adsorbers used as control devices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... control device. If an owner or operator elects to replace a control device on a Group 1 process vent or... 40 Protection of Environment 15 2011-07-01 2011-07-01 false Carbon adsorbers used as control... PROGRAMS (CONTINUED) CONSOLIDATED FEDERAL AIR RULE Closed Vent Systems, Control Devices, and Routing to a...

21 CFR 120.8 - Hazard Analysis and Critical Control Point (HACCP) plan.

Code of Federal Regulations, 2011 CFR

2011-04-01

...: (i) Critical control points designed to control food hazards that are reasonably likely to occur and could be introduced inside the processing plant environment; and (ii) Critical control points designed... 21 Food and Drugs 2 2011-04-01 2011-04-01 false Hazard Analysis and Critical Control Point (HACCP...

Composite-Metal-Matrix Arc-Spray Process

NASA Technical Reports Server (NTRS)

Westfall, Leonard J.

1987-01-01

Arc-spray "monotape" process automated, low in cost, and produces at high rate. Ideal for development of new metal-matrix composites. "Monotape" reproducible and of high quality. Process carried out in controlled gas environment with programmable matrix-deposition rates, resulting in significant cost saving

40 CFR 60.5415 - How do I demonstrate continuous compliance with the standards for my gas well affected facility...

Code of Federal Regulations, 2013 CFR

2013-07-01

... plants? 60.5415 Section 60.5415 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR..., and unavoidable failure of air pollution control equipment, process equipment, or a process to operate... control systems were kept in operation if at all possible, consistent with safety and good air pollution...

40 CFR 63.1406 - Reactor batch process vent provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 11 2011-07-01 2011-07-01 false Reactor batch process vent provisions... § 63.1406 Reactor batch process vent provisions. (a) Emission standards. Owners or operators of reactor... reactor batch process vent located at a new affected source shall control organic HAP emissions by...

40 CFR 63.1406 - Reactor batch process vent provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Reactor batch process vent provisions... § 63.1406 Reactor batch process vent provisions. (a) Emission standards. Owners or operators of reactor... reactor batch process vent located at a new affected source shall control organic HAP emissions by...

40 CFR 63.140 - Process wastewater provisions-delay of repair.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 10 2014-07-01 2014-07-01 false Process wastewater provisions-delay of... Manufacturing Industry for Process Vents, Storage Vessels, Transfer Operations, and Wastewater § 63.140 Process wastewater provisions—delay of repair. (a) Delay of repair of equipment for which a control equipment failure...

40 CFR 63.140 - Process wastewater provisions-delay of repair.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 10 2012-07-01 2012-07-01 false Process wastewater provisions-delay of... Manufacturing Industry for Process Vents, Storage Vessels, Transfer Operations, and Wastewater § 63.140 Process wastewater provisions—delay of repair. (a) Delay of repair of equipment for which a control equipment failure...

40 CFR 63.140 - Process wastewater provisions-delay of repair.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 9 2011-07-01 2011-07-01 false Process wastewater provisions-delay of... Manufacturing Industry for Process Vents, Storage Vessels, Transfer Operations, and Wastewater § 63.140 Process wastewater provisions—delay of repair. (a) Delay of repair of equipment for which a control equipment failure...

40 CFR 63.140 - Process wastewater provisions-delay of repair.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 10 2013-07-01 2013-07-01 false Process wastewater provisions-delay of... Manufacturing Industry for Process Vents, Storage Vessels, Transfer Operations, and Wastewater § 63.140 Process wastewater provisions—delay of repair. (a) Delay of repair of equipment for which a control equipment failure...

40 CFR 761.369 - Pre-cleaning the surface.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Pre-cleaning the surface. 761.369 Section 761.369 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT POLYCHLORINATED BIPHENYLS (PCBs) MANUFACTURING, PROCESSING, DISTRIBUTION IN COMMERCE, AND USE...

Pavlovian control of cross-tolerance between pentobarbital and ethanol.

PubMed

Cappell, H; Roach, C; Poulos, C X

1981-01-01

Tolerance to several effects of a number of drugs has been shown to depend on Pavlovian conditioning processes. Experiment I extended the compensatory conditioning model (Siegel 1975) to tolerance to the hypothermic effect of pentobarbital (30 mg/kg). In Experiment I, rats that acquired hypothermic tolerance in one environment did not display tolerance when tested in an environment not previously associated with drug administration. In Experiment II, rats were made tolerant to the hypothermic effect of pentobarbital (30 mg/kg) and tested for cross-tolerance to ethanol (2.5 g/kg). Cross-tolerance was observed, but it was significantly reduced if the test was in an environment different from the one in which tolerance to pentobarbital was originally acquired. Thus, the compensatory conditioning model accounts for at least part of the tolerance and cross-tolerance to the thermic effects of alcohol and pentobarbital. The physiological processes in the CNS underlying tolerance and cross-tolerance for these drugs, therefore, are controlled by associative processes.

The Design and Development of an Omni-Directional Mobile Robot Oriented to an Intelligent Manufacturing System

PubMed Central

Qian, Jun; Zi, Bin; Ma, Yangang; Zhang, Dan

2017-01-01

In order to transport materials flexibly and smoothly in a tight plant environment, an omni-directional mobile robot based on four Mecanum wheels was designed. The mechanical system of the mobile robot is made up of three separable layers so as to simplify its combination and reorganization. Each modularized wheel was installed on a vertical suspension mechanism, which ensures the moving stability and keeps the distances of four wheels invariable. The control system consists of two-level controllers that implement motion control and multi-sensor data processing, respectively. In order to make the mobile robot navigate in an unknown semi-structured indoor environment, the data from a Kinect visual sensor and four wheel encoders were fused to localize the mobile robot using an extended Kalman filter with specific processing. Finally, the mobile robot was integrated in an intelligent manufacturing system for material conveying. Experimental results show that the omni-directional mobile robot can move stably and autonomously in an indoor environment and in industrial fields. PMID:28891964

The Design and Development of an Omni-Directional Mobile Robot Oriented to an Intelligent Manufacturing System.

PubMed

Qian, Jun; Zi, Bin; Wang, Daoming; Ma, Yangang; Zhang, Dan

2017-09-10

In order to transport materials flexibly and smoothly in a tight plant environment, an omni-directional mobile robot based on four Mecanum wheels was designed. The mechanical system of the mobile robot is made up of three separable layers so as to simplify its combination and reorganization. Each modularized wheel was installed on a vertical suspension mechanism, which ensures the moving stability and keeps the distances of four wheels invariable. The control system consists of two-level controllers that implement motion control and multi-sensor data processing, respectively. In order to make the mobile robot navigate in an unknown semi-structured indoor environment, the data from a Kinect visual sensor and four wheel encoders were fused to localize the mobile robot using an extended Kalman filter with specific processing. Finally, the mobile robot was integrated in an intelligent manufacturing system for material conveying. Experimental results show that the omni-directional mobile robot can move stably and autonomously in an indoor environment and in industrial fields.

Neuromorphic Learning From Noisy Data

NASA Technical Reports Server (NTRS)

Merrill, Walter C.; Troudet, Terry

1993-01-01

Two reports present numerical study of performance of feedforward neural network trained by back-propagation algorithm in learning continuous-valued mappings from data corrupted by noise. Two types of noise considered: plant noise which affects dynamics of controlled process and data-processing noise, which occurs during analog processing and digital sampling of signals. Study performed with view toward use of neural networks as neurocontrollers to substitute for, or enhance, performances of human experts in controlling mechanical devices in presence of sensor and actuator noise and to enhance performances of more-conventional digital feedback electronic process controllers in noisy environments.

Intelligent monitoring and control of semiconductor manufacturing equipment

NASA Technical Reports Server (NTRS)

Murdock, Janet L.; Hayes-Roth, Barbara

1991-01-01

The use of AI methods to monitor and control semiconductor fabrication in a state-of-the-art manufacturing environment called the Rapid Thermal Multiprocessor is described. Semiconductor fabrication involves many complex processing steps with limited opportunities to measure process and product properties. By applying additional process and product knowledge to that limited data, AI methods augment classical control methods by detecting abnormalities and trends, predicting failures, diagnosing, planning corrective action sequences, explaining diagnoses or predictions, and reacting to anomalous conditions that classical control systems typically would not correct. Research methodology and issues are discussed, and two diagnosis scenarios are examined.

The relationship between health related quality of life and sensory deficits among patients with diabetes mellitus.

PubMed

Engel-Yeger, Batya; Darawsha Najjar, Sanaa; Darawsha, Mahmud

2017-08-13

(1) To profile sensory deficits examined in the ability to process sensory information from daily environment and discriminate between tactile stimuli among patients with controlled and un-controlled diabetes mellitus. (2) Examine the relationship between the sensory deficits and patients' health-related quality of life. This study included 115 participants aged 33-55 with uncontrolled (n = 22) or controlled (n = 24) glycemic levels together with healthy subjects (n = 69). All participants completed the brief World Health Organization Quality of Life Questionnaire, the Adolescent/Adult Sensory Profile and performed the tactile discrimination test. Sensory deficits were more emphasized among patients with uncontrolled glycemic levels as expressed in difficulties to register sensory input, lower sensation seeking in daily environments and difficulties to discriminate between tactile stimuli. They also reported the lowest physical and social quality of life as compared to the other two groups. Better sensory seeking and registration predicted better quality of life. Disease control and duration contributed to these predictions. Difficulties in processing sensory information from their daily environments are particularly prevalent among patients with uncontrolled glycemic levels, and significantly impacted their quality of life. Clinicians should screen for sensory processing difficulties among patients with diabetes mellitus and understand their impacts on patients' quality of life. Implications for Rehabilitation Patients with diabetes mellitus, and particularly those with uncontrolled glycemic levels, may have difficulties in processing sensory information from daily environment. A multidisciplinary intervention approach is recommended: clinicians should screen for sensory processing deficits among patients with diabetes mellitus and understand their impacts on patients' daily life. By providing the patients with environmental adaptations and coping strategies, clinicians may assist in optimizing sensory experiences in real life context and elevate patients' quality of life. Relating to quality of life and emphasizing a multidisciplinary approach is of major importance in broadening our understanding of health conditions and providing holistic treatment for patients.

40 CFR 763.175 - Enforcement.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Prohibition of the Manufacture, Importation, Processing, and Distribution in Commerce of Certain Asbestos... the manufacture, import, processing, or distribution in commerce of asbestos-containing products in...

Chaotic home environment is associated with reduced infant processing speed under high task demands.

PubMed

Tomalski, Przemysław; Marczuk, Karolina; Pisula, Ewa; Malinowska, Anna; Kawa, Rafał; Niedźwiecka, Alicja

2017-08-01

Early adversity has profound long-term consequences for child development across domains. The effects of early adversity on structural and functional brain development were shown for infants under 12 months of life. However, the causal mechanisms of these effects remain relatively unexplored. Using a visual habituation task we investigated whether chaotic home environment may affect processing speed in 5.5 month-old infants (n=71). We found detrimental effects of chaos on processing speed for complex but not for simple visual stimuli. No effects of socio-economic status on infant processing speed were found although the sample was predominantly middle class. Our results indicate that chaotic early environment may adversely affect processing speed in early infancy, but only when greater cognitive resources need to be deployed. The study highlights an attractive avenue for research on the mechanisms linking home environment with the development of attention control. Copyright © 2017 Elsevier Inc. All rights reserved.

Implications of acceleration environments on scaling materials processing in space to production

NASA Technical Reports Server (NTRS)

Demel, Ken

1990-01-01

Some considerations regarding materials processing in space are covered from a commercial perspective. Key areas include power, proprietary data, operational requirements (including logistics), and also the center of gravity location, and control of that location with respect to materials processing payloads.

Argon-oxygen atmospheric pressure plasma treatment on carbon fiber reinforced polymer for improved bonding

NASA Astrophysics Data System (ADS)

Chartosias, Marios

Acceptance of Carbon Fiber Reinforced Polymer (CFRP) structures requires a robust surface preparation method with improved process controls capable of ensuring high bond quality. Surface preparation in a production clean room environment prior to applying adhesive for bonding would minimize risk of contamination and reduce cost. Plasma treatment is a robust surface preparation process capable of being applied in a production clean room environment with process parameters that are easily controlled and documented. Repeatable and consistent processing is enabled through the development of a process parameter window utilizing techniques such as Design of Experiments (DOE) tailored to specific adhesive and substrate bonding applications. Insight from respective plasma treatment Original Equipment Manufacturers (OEMs) and screening tests determined critical process factors from non-factors and set the associated factor levels prior to execution of the DOE. Results from mode I Double Cantilever Beam (DCB) testing per ASTM D 5528 [1] standard and DOE statistical analysis software are used to produce a regression model and determine appropriate optimum settings for each factor.

40 CFR 725.300 - Scope and purpose.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Scope and purpose. 725.300 Section 725.300 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Exemptions for Test Marketing § 725.300 Scope...

A comparison of force control algorithms for robots in contact with flexible environments

NASA Technical Reports Server (NTRS)

Wilfinger, Lee S.

1992-01-01

In order to perform useful tasks, the robot end-effector must come into contact with its environment. For such tasks, force feedback is frequently used to control the interaction forces. Control of these forces is complicated by the fact that the flexibility of the environment affects the stability of the force control algorithm. Because of the wide variety of different materials present in everyday environments, it is necessary to gain an understanding of how environmental flexibility affects the stability of force control algorithms. This report presents the theory and experimental results of two force control algorithms: Position Accommodation Control and Direct Force Servoing. The implementation of each of these algorithms on a two-arm robotic test bed located in the Center for Intelligent Robotic Systems for Space Exploration (CIRSSE) is discussed in detail. The behavior of each algorithm when contacting materials of different flexibility is experimentally determined. In addition, several robustness improvements to the Direct Force Servoing algorithm are suggested and experimentally verified. Finally, a qualitative comparison of the force control algorithms is provided, along with a description of a general tuning process for each control method.

DHM simulation in virtual environments: a case-study on control room design.

PubMed

Zamberlan, M; Santos, V; Streit, P; Oliveira, J; Cury, R; Negri, T; Pastura, F; Guimarães, C; Cid, G

2012-01-01

This paper will present the workflow developed for the application of serious games in the design of complex cooperative work settings. The project was based on ergonomic studies and development of a control room among participative design process. Our main concerns were the 3D human virtual representation acquired from 3D scanning, human interaction, workspace layout and equipment designed considering ergonomics standards. Using Unity3D platform to design the virtual environment, the virtual human model can be controlled by users on dynamic scenario in order to evaluate the new work settings and simulate work activities. The results obtained showed that this virtual technology can drastically change the design process by improving the level of interaction between final users and, managers and human factors team.

Marine biosurfaces research program

NASA Astrophysics Data System (ADS)

The Office of Naval Research (ONR) of the U.S. Navy is starting a basic research program to address the initial events that control colonization of surfaces by organisms in marine environments. The program “arises from the Navy's need to understand and ultimately control biofouling and biocorrosion in marine environments,” according to a Navy announcement.The program, “Biological Processes Controlling Surface Modification in the Marine Environment,” will emphasize the application of in situ techniques and modern molecular biological, biochemical, and biophysical approaches; it will also encourage the development of interdisciplinary projects. Specific areas of interest include sensing and response to environmental surface (physiology/physical chemistry), factors controlling movement to and retention at surfaces (behavior/hydrodynamics), genetic regulation of attachment (molecular genetics), and mechanisms of attachment (biochemistry/surface chemistry).

[Organization of monitoring of electromagnetic radiation in the urban environment].

PubMed

Savel'ev, S I; Dvoeglazova, S V; Koz'min, V A; Kochkin, D E; Begishev, M R

2008-01-01

The authors describe new current approaches to monitoring the environment, including the sources of electromagnetic radiation and noise. Electronic maps of the area under study are shown to be made, by constructing the isolines or distributing the actual levels of controlled factors. These current approaches to electromagnetic and acoustic monitoring make it possible to automate a process of measurements, to analyze the established situation, and to simplify the risk controlling methodology.

40 CFR 763.160 - Scope.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Prohibition of the Manufacture, Importation, Processing, and Distribution in Commerce of Certain Asbestos..., importation, processing, and distribution in commerce of the asbestos-containing products identified and at...

40 CFR 763.160 - Scope.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Prohibition of the Manufacture, Importation, Processing, and Distribution in Commerce of Certain Asbestos..., importation, processing, and distribution in commerce of the asbestos-containing products identified and at...

40 CFR 763.160 - Scope.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Prohibition of the Manufacture, Importation, Processing, and Distribution in Commerce of Certain Asbestos..., importation, processing, and distribution in commerce of the asbestos-containing products identified and at...

40 CFR 763.160 - Scope.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Prohibition of the Manufacture, Importation, Processing, and Distribution in Commerce of Certain Asbestos..., importation, processing, and distribution in commerce of the asbestos-containing products identified and at...

From chaos to control: winning the war.

PubMed

Wojciak, P J

1994-08-01

This article illustrates how a small manufacturing facility in the Midwest undertook the process of an MRP II implementation and ultimately gained class A status at a true make-or-break time in its history. The control that was gained throughout the entire process has helped create a winning environment and will continue to strengthen our position as we move toward world-class excellence.

40 CFR 63.2252 - What are the requirements for process units that have no control or work practice requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true What are the requirements for process units that have no control or work practice requirements? 63.2252 Section 63.2252 Protection of... Pollutants: Plywood and Composite Wood Products General Compliance Requirements § 63.2252 What are the...

A Web-Based Monitoring System for Multidisciplinary Design Projects

NASA Technical Reports Server (NTRS)

Rogers, James L.; Salas, Andrea O.; Weston, Robert P.

1998-01-01

In today's competitive environment, both industry and government agencies are under pressure to reduce the time and cost of multidisciplinary design projects. New tools have been introduced to assist in this process by facilitating the integration of and communication among diverse disciplinary codes. One such tool, a framework for multidisciplinary computational environments, is defined as a hardware and software architecture that enables integration, execution, and communication among diverse disciplinary processes. An examination of current frameworks reveals weaknesses in various areas, such as sequencing, displaying, monitoring, and controlling the design process. The objective of this research is to explore how Web technology, integrated with an existing framework, can improve these areas of weakness. This paper describes a Web-based system that optimizes and controls the execution sequence of design processes; and monitors the project status and results. The three-stage evolution of the system with increasingly complex problems demonstrates the feasibility of this approach.

Infection prevention and control in the design of healthcare facilities.

PubMed

Farrow, Tye S; Black, Stephen M

2009-01-01

The lead paper, "Healthcare-Associated Infections as Patient Safety Indicators," written by Gardam, Lemieux, Reason, van Dijk and Goel, puts forward the design of healthcare facilities as one of many strategies to improve patient safety with respect to healthcare-associated infections. This commentary explores some of the issues in balancing infection prevention and control priorities with other needs and values brought to the design process. This balance is challenged not only by a lack of supporting evidence but also by the superficial nature in which infection prevention and control are often discussed within a design context. For the physical environment to support any patient safety initiative, the design of the processes must be developed in conjunction with that of the physical environment so that compliance can be natural and convenient. Finally, consideration is given to the value of documenting decision-making related to infection prevention and control in facility design and ongoing assessments of existing facilities.

Methods and Apparatus for Autonomous Robotic Control

NASA Technical Reports Server (NTRS)

Gorshechnikov, Anatoly (Inventor); Livitz, Gennady (Inventor); Versace, Massimiliano (Inventor); Palma, Jesse (Inventor)

2017-01-01

Sensory processing of visual, auditory, and other sensor information (e.g., visual imagery, LIDAR, RADAR) is conventionally based on "stovepiped," or isolated processing, with little interactions between modules. Biological systems, on the other hand, fuse multi-sensory information to identify nearby objects of interest more quickly, more efficiently, and with higher signal-to-noise ratios. Similarly, examples of the OpenSense technology disclosed herein use neurally inspired processing to identify and locate objects in a robot's environment. This enables the robot to navigate its environment more quickly and with lower computational and power requirements.

40 CFR 65.150 - Absorbers used as control devices.

Code of Federal Regulations, 2014 CFR

2014-07-01

... control device on a Group 1 process vent or a high-throughput transfer rack with an absorber used as a... 40 Protection of Environment 16 2014-07-01 2014-07-01 false Absorbers used as control devices. 65... (CONTINUED) CONSOLIDATED FEDERAL AIR RULE Closed Vent Systems, Control Devices, and Routing to a Fuel Gas...

40 CFR 65.151 - Condensers used as control devices.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the design evaluation for storage vessels and low-throughput transfer rack controls. As provided in... control device on a Group 1 process vent or a high-throughput transfer rack with a condenser used as a... 40 Protection of Environment 16 2014-07-01 2014-07-01 false Condensers used as control devices. 65...

40 CFR 65.150 - Absorbers used as control devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... control device on a Group 1 process vent or a high-throughput transfer rack with an absorber used as a... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Absorbers used as control devices. 65... (CONTINUED) CONSOLIDATED FEDERAL AIR RULE Closed Vent Systems, Control Devices, and Routing to a Fuel Gas...

40 CFR 65.150 - Absorbers used as control devices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... control device on a Group 1 process vent or a high-throughput transfer rack with an absorber used as a... 40 Protection of Environment 15 2011-07-01 2011-07-01 false Absorbers used as control devices. 65... (CONTINUED) CONSOLIDATED FEDERAL AIR RULE Closed Vent Systems, Control Devices, and Routing to a Fuel Gas...

40 CFR 65.151 - Condensers used as control devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the design evaluation for storage vessels and low-throughput transfer rack controls. As provided in... control device on a Group 1 process vent or a high-throughput transfer rack with a condenser used as a... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Condensers used as control devices. 65...

40 CFR 65.151 - Condensers used as control devices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the design evaluation for storage vessels and low-throughput transfer rack controls. As provided in... control device on a Group 1 process vent or a high-throughput transfer rack with a condenser used as a... 40 Protection of Environment 15 2011-07-01 2011-07-01 false Condensers used as control devices. 65...

Collisional cascading - The limits of population growth in low earth orbit

NASA Technical Reports Server (NTRS)

Kessler, Donald J.

1991-01-01

Random collisions between made-made objects in earth orbit will lead to a significant source of orbital debris, but there are a number of uncertainties in these models, and additional analysis and data are required to fully characterize the future environment. However, the nature of these uncertainties are such that while the future environment is uncertain, the fact that collisions will control the future environment is less uncertain. The data that already exist is sufficient to show that cascading collisions will control the future debris environment with no, or very minor increases in the current low-earth-orbit population. Two populations control this process: explosion fragments and expended rocket bodies and payloads. Practices are already changing to limit explosions in low earth orbit; it is necessary to begin limiting the number of expended rocket bodies and payloads in orbit.

Research into software executives for space operations support

NASA Technical Reports Server (NTRS)

Collier, Mark D.

1990-01-01

Research concepts pertaining to a software (workstation) executive which will support a distributed processing command and control system characterized by high-performance graphics workstations used as computing nodes are presented. Although a workstation-based distributed processing environment offers many advantages, it also introduces a number of new concerns. In order to solve these problems, allow the environment to function as an integrated system, and present a functional development environment to application programmers, it is necessary to develop an additional layer of software. This 'executive' software integrates the system, provides real-time capabilities, and provides the tools necessary to support the application requirements.

40 CFR 65.141 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Definitions. 65.141 Section 65.141 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONSOLIDATED FEDERAL AIR RULE Closed Vent Systems, Control Devices, and Routing to a Fuel Gas System or a Process § 65...

40 CFR 63.1275 - Glycol dehydration unit process vent standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 12 2014-07-01 2014-07-01 false Glycol dehydration unit process vent... Storage Facilities § 63.1275 Glycol dehydration unit process vent standards. (a) This section applies to each glycol dehydration unit subject to this subpart that must be controlled for air emissions as...

40 CFR 63.1275 - Glycol dehydration unit process vent standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 12 2013-07-01 2013-07-01 false Glycol dehydration unit process vent... Storage Facilities § 63.1275 Glycol dehydration unit process vent standards. (a) This section applies to each glycol dehydration unit subject to this subpart that must be controlled for air emissions as...

A Structured, Yet Agile Approach to Designing C2 Operating Environments

DTIC Science & Technology

2012-06-01

PROCESS ........................................................ 22 APPENDIX A: SUPPLEMENTAL MATERIAL...organization’s mission effectiveness. Lastly, he identifies the mechanisms for C2 agility, enabled by people, processes , information, systems...operations, controls forces, and coordinates operational activities and/or a facility that is organized to gather, process , analyze, dispatch, and

40 CFR 426.27 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... conventional pollutant control technology: There shall be no discharge of process waste water pollutants to... control technology. 426.27 Section 426.27 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... attainable by the application of the best conventional pollutant control technology. The following...

40 CFR 418.77 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... conventional pollutant control technology: There shall be no discharge of process waste water pollutants to... control technology. 418.77 Section 418.77 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... effluent reduction attainable by the application of the best conventional pollutant control technology. The...

40 CFR 424.57 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... conventional pollutant control technology: There shall be no discharge of process waste water pollutants to... control technology. 424.57 Section 424.57 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... reduction attainable by the application of the best conventional pollutant control technology. The following...

40 CFR 418.67 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... conventional pollutant control technology: There shall be no discharge of process waste water pollutants to... control technology. 418.67 Section 418.67 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... attainable by the application of the best conventional pollutant control technology. The following...

40 CFR 426.37 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... conventional pollutant control technology: There shall be no discharge of process waste water pollutants to... control technology. 426.37 Section 426.37 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... attainable by the application of the best conventional pollutant control technology. The following...

Laboratory Control System's Effects on Student Achievement and Attitudes

ERIC Educational Resources Information Center

Cicek, Fatma Gozalan; Taspinar, Mehmet

2016-01-01

Problem Statement: The current study investigates whether the learning environment designed based on the laboratory control system affects the academic achievement, the attitude toward the learning-teaching process and the retention of the students in computer education. Purpose of Study: The study aims to identify the laboratory control system…

Fault-tolerant Control of a Cyber-physical System

NASA Astrophysics Data System (ADS)

Roxana, Rusu-Both; Eva-Henrietta, Dulf

2017-10-01

Cyber-physical systems represent a new emerging field in automatic control. The fault system is a key component, because modern, large scale processes must meet high standards of performance, reliability and safety. Fault propagation in large scale chemical processes can lead to loss of production, energy, raw materials and even environmental hazard. The present paper develops a multi-agent fault-tolerant control architecture using robust fractional order controllers for a (13C) cryogenic separation column cascade. The JADE (Java Agent DEvelopment Framework) platform was used to implement the multi-agent fault tolerant control system while the operational model of the process was implemented in Matlab/SIMULINK environment. MACSimJX (Multiagent Control Using Simulink with Jade Extension) toolbox was used to link the control system and the process model. In order to verify the performance and to prove the feasibility of the proposed control architecture several fault simulation scenarios were performed.

Synthetic Biology: Tools to Design, Build, and Optimize Cellular Processes

PubMed Central

Young, Eric; Alper, Hal

2010-01-01

The general central dogma frames the emergent properties of life, which make biology both necessary and difficult to engineer. In a process engineering paradigm, each biological process stream and process unit is heavily influenced by regulatory interactions and interactions with the surrounding environment. Synthetic biology is developing the tools and methods that will increase control over these interactions, eventually resulting in an integrative synthetic biology that will allow ground-up cellular optimization. In this review, we attempt to contextualize the areas of synthetic biology into three tiers: (1) the process units and associated streams of the central dogma, (2) the intrinsic regulatory mechanisms, and (3) the extrinsic physical and chemical environment. Efforts at each of these three tiers attempt to control cellular systems and take advantage of emerging tools and approaches. Ultimately, it will be possible to integrate these approaches and realize the vision of integrative synthetic biology when cells are completely rewired for biotechnological goals. This review will highlight progress towards this goal as well as areas requiring further research. PMID:20150964

Adaptation of a Control Center Development Environment for Industrial Process Control

NASA Technical Reports Server (NTRS)

Killough, Ronnie L.; Malik, James M.

1994-01-01

In the control center, raw telemetry data is received for storage, display, and analysis. This raw data must be combined and manipulated in various ways by mathematical computations to facilitate analysis, provide diversified fault detection mechanisms, and enhance display readability. A development tool called the Graphical Computation Builder (GCB) has been implemented which provides flight controllers with the capability to implement computations for use in the control center. The GCB provides a language that contains both general programming constructs and language elements specifically tailored for the control center environment. The GCB concept allows staff who are not skilled in computer programming to author and maintain computer programs. The GCB user is isolated from the details of external subsystem interfaces and has access to high-level functions such as matrix operators, trigonometric functions, and unit conversion macros. The GCB provides a high level of feedback during computation development that improves upon the often cryptic errors produced by computer language compilers. An equivalent need can be identified in the industrial data acquisition and process control domain: that of an integrated graphical development tool tailored to the application to hide the operating system, computer language, and data acquisition interface details. The GCB features a modular design which makes it suitable for technology transfer without significant rework. Control center-specific language elements can be replaced by elements specific to industrial process control.

Utilizing Controlled Vibrations in a Microgravity Environment to Understand and Promote Microstructural Homogeneity During Floating-Zone Crystal Growth

NASA Technical Reports Server (NTRS)

Grugel, Richard N.

1999-01-01

It has been demonstrated in floating-zone configurations utilizing silicone oil and nitrate salts that mechanically induced vibration effectively minimizes detrimental, gravity independent, thermocapillary flow. The processing parameters leading to crystal improvement and aspects of the on-going modeling effort are discussed. Plans for applying the crystal growth technique to commercially relevant materials, e.g., silicon, as well as the value of processing in a microgravity environment are presented.

Performance of redundant disk array organizations in transaction processing environments

NASA Technical Reports Server (NTRS)

Mourad, Antoine N.; Fuchs, W. K.; Saab, Daniel G.

1993-01-01

A performance evaluation is conducted for two redundant disk-array organizations in a transaction-processing environment, relative to the performance of both mirrored disk organizations and organizations using neither striping nor redundancy. The proposed parity-striping alternative to striping with rotated parity is shown to furnish rapid recovery from failure at the same low storage cost without interleaving the data over multiple disks. Both noncached systems and systems using a nonvolatile cache as the controller are considered.

A senior manufacturing laboratory for determining injection molding process capability

NASA Technical Reports Server (NTRS)

Wickman, Jerry L.; Plocinski, David

1992-01-01

The following is a laboratory experiment designed to further understanding of materials science. This subject material is directed at an upper level undergraduate/graduate student in an Engineering or Engineering Technology program. It is assumed that the student has a thorough understanding of the process and quality control. The format of this laboratory does not follow that which is normally recommended because of the nature of process capability and that of the injection molding equipment and tooling. This laboratory is instead developed to be used as a point of departure for determining process capability for any process in either a quality control laboratory or a manufacturing environment where control charts, process capability, and experimental or product design are considered important topics.

The organization of perception and action in complex control skills

NASA Technical Reports Server (NTRS)

Miller, Richard A.; Jagacinski, Richard J.

1989-01-01

An attempt was made to describe the perceptual, cognitive, and action processes that account for highly skilled human performance in complex task environments. In order to study such a performance in a controlled setting, a laboratory task was constructed and three experiments were performed using human subjects. A general framework was developed for describing the organization of perceptual, cognitive, and action process.

40 CFR 63.1034 - Closed vent systems and control devices; or emissions routed to a fuel gas system or process...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Closed vent systems and control devices; or emissions routed to a fuel gas system or process standards. 63.1034 Section 63.1034 Protection... stringent. The 20 parts per million by volume standard is not applicable to the provisions of § 63.1016. (ii...

40 CFR 63.1034 - Closed vent systems and control devices; or emissions routed to a fuel gas system or process...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 10 2011-07-01 2011-07-01 false Closed vent systems and control devices; or emissions routed to a fuel gas system or process standards. 63.1034 Section 63.1034 Protection... stringent. The 20 parts per million by volume standard is not applicable to the provisions of § 63.1016. (ii...

Structured Kernel Subspace Learning for Autonomous Robot Navigation.

PubMed

Kim, Eunwoo; Choi, Sungjoon; Oh, Songhwai

2018-02-14

This paper considers two important problems for autonomous robot navigation in a dynamic environment, where the goal is to predict pedestrian motion and control a robot with the prediction for safe navigation. While there are several methods for predicting the motion of a pedestrian and controlling a robot to avoid incoming pedestrians, it is still difficult to safely navigate in a dynamic environment due to challenges, such as the varying quality and complexity of training data with unwanted noises. This paper addresses these challenges simultaneously by proposing a robust kernel subspace learning algorithm based on the recent advances in nuclear-norm and l 1 -norm minimization. We model the motion of a pedestrian and the robot controller using Gaussian processes. The proposed method efficiently approximates a kernel matrix used in Gaussian process regression by learning low-rank structured matrix (with symmetric positive semi-definiteness) to find an orthogonal basis, which eliminates the effects of erroneous and inconsistent data. Based on structured kernel subspace learning, we propose a robust motion model and motion controller for safe navigation in dynamic environments. We evaluate the proposed robust kernel learning in various tasks, including regression, motion prediction, and motion control problems, and demonstrate that the proposed learning-based systems are robust against outliers and outperform existing regression and navigation methods.

Effect of HIV/AIDS on the control environment.

PubMed

Coetzee, Philna

2006-07-01

The management of organizations is responsible for risk management and control systems. HIV/AIDS could be a great threat in the achievement of strategic business objectives, implicating a great concern for management. Management needs to understand this possible risk. This study aims to identify the effect that HIV/AIDS could have on the different elements of the control environment. The archival research method was used. It was established that no formal research was conducted to date on the effect of HIV/AIDS on the control environment as a whole. Various studies have included the effect of HIV/AIDS on certain factors of the control environment. These studies will be discussed briefly to identify relevant findings. The study indicated that the disease could affect various aspects of the control environment, namely: competency of the workforce (e.g. productivity, quality of work, absenteeism, loss of skills and knowledge, training and recruitment, etc.); organizational structure (e.g. increase use of technology labour, disruption of processes, level of employees affected by the disease); human resource (HR) policies and practices (e.g. legislation applicable, prevention and awareness programmes, compensation and benefits). Research limitation: HIV/AIDS is a relatively new potential risk to organizations. Knowledge of the disease is limited. HIV/AIDS is also a very sensitive issue as people fear the disease and do not like to discuss its existence. Government determined that it should be a non-notifiable disease and the disease is currently greatly stigmatized. The databases of companies investigated by other research studies were not developed to gather all the relevant information. Management should be aware that HIV/AIDS poses a possible risk to organizations. Data on the effect of HIV/AIDS should be gathered and used in the decision-making process on how to manage this risk. To be able to fulfil this duty, management first has to determine: whether HIV/AIDS is a risk; the relevant cost involved that the disease is costing the organization; how to control these costs.

Lightweight UDP Pervasive Protocol in Smart Home Environment Based on Labview

NASA Astrophysics Data System (ADS)

Kurniawan, Wijaya; Hannats Hanafi Ichsan, Mochammad; Rizqika Akbar, Sabriansyah; Arwani, Issa

2017-04-01

TCP (Transmission Control Protocol) technology in a reliable environment was not a problem, but not in an environment where the entire Smart Home network connected locally. Currently employing pervasive protocols using TCP technology, when data transmission is sent, it would be slower because they have to perform handshaking process in advance and could not broadcast the data. On smart home environment, it does not need large size and complex data transmission between monitoring site and monitoring center required in Smart home strain monitoring system. UDP (User Datagram Protocol) technology is quick and simple on data transmission process. UDP can broadcast messages because the UDP did not require handshaking and with more efficient memory usage. LabVIEW is a programming language software for processing and visualization of data in the field of data acquisition. This paper proposes to examine Pervasive UDP protocol implementations in smart home environment based on LabVIEW. UDP coded in LabVIEW and experiments were performed on a PC and can work properly.

Proceedings of the 3rd Annual Conference on Aerospace Computational Control, volume 2

NASA Technical Reports Server (NTRS)

Bernard, Douglas E. (Editor); Man, Guy K. (Editor)

1989-01-01

This volume of the conference proceedings contain papers and discussions in the following topical areas: Parallel processing; Emerging integrated capabilities; Low order controllers; Real time simulation; Multibody component representation; User environment; and Distributed parameter techniques.

40 CFR 240.205-2 - Recommended procedures: Design.

Code of Federal Regulations, 2010 CFR

2010-07-01

....205-2 Section 240.205-2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures... air pollution control technology. (b) All emissions, including dust from vents, should be controlled. ...

40 CFR 240.205-2 - Recommended procedures: Design.

Code of Federal Regulations, 2011 CFR

2011-07-01

....205-2 Section 240.205-2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures... air pollution control technology. (b) All emissions, including dust from vents, should be controlled. ...

Effects of space flight on locomotor control

NASA Technical Reports Server (NTRS)

Bloomberg, Jacob J.; Layne, Charles S.; McDonald, P. Vernon; Peters, Brian T.; Huebner, William P.; Reschke, Millard F.; Berthoz, Alain; Glasauer, Stefan; Newman, Dava; Jackson, D. Keoki

1999-01-01

In the microgravity environment of spaceflight, the relationship between sensory input and motor output is altered. During prolonged missions, neural adaptive processes come into play to recalibrate central nervous system function, thereby permitting new motor control strategies to emerge in the novel sensory environment of microgravity. However, the adaptive state achieved during spaceflight is inappropriate for a unit gravity environment and leads to motor control alterations upon return to Earth that include disturbances in locomotion. Indeed, gait and postural instabilities following the return to Earth have been reported in both U.S. astronauts and Russian cosmonauts even after short duration (5- to 10-day) flights. After spaceflight, astronauts may: (1) experience the sensation of turning while attempting to walk a straight path, (2) encounter sudden loss of postural stability, especially when rounding corners, (3) perceive exaggerated pitch and rolling head movements during walking, (4) experience sudden loss of orientation in unstructured visual environments, or (5) experience significant oscillopsia during locomotion.

Determining the potential productivity of food crops in controlled environments

NASA Technical Reports Server (NTRS)

Bugbee, Bruce

1992-01-01

The quest to determine the maximum potential productivity of food crops is greatly benefitted by crop growth models. Many models have been developed to analyze and predict crop growth in the field, but it is difficult to predict biological responses to stress conditions. Crop growth models for the optimal environments of a Controlled Environment Life Support System (CELSS) can be highly predictive. This paper discusses the application of a crop growth model to CELSS; the model is used to evaluate factors limiting growth. The model separately evaluates the following four physiological processes: absorption of PPF by photosynthetic tissue, carbon fixation (photosynthesis), carbon use (respiration), and carbon partitioning (harvest index). These constituent processes determine potentially achievable productivity. An analysis of each process suggests that low harvest index is the factor most limiting to yield. PPF absorption by plant canopies and respiration efficiency are also of major importance. Research concerning productivity in a CELSS should emphasize: (1) the development of gas exchange techniques to continuously monitor plant growth rates and (2) environmental techniques to reduce plant height in communities.

Basic principles of a flexible astronomical data processing system in UNIX environment.

NASA Astrophysics Data System (ADS)

Verkhodanov, O. V.; Erukhimov, B. L.; Monosov, M. L.; Chernenkov, V. N.; Shergin, V. S.

Methods of construction of a flexible system for astronomical data processing (FADPS) are described. An example of construction of such a FADPS for continuum radiometer data of the RATAN-600 is presented. The Job Control Language of this system is the Job Control Language of OS UNIX. It is shown that using basic commands of the data processing system (DPS) a user, knowing basic principles of Job in OS UNIX, can create his own mini-DPS. Examples of such mini-DPSs are presented.

VIEW OF THE INTERIOR OF BUILDING 125, THE STANDARDS LABORATORY. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF THE INTERIOR OF BUILDING 125, THE STANDARDS LABORATORY. THE PRIMARY FUNCTION OF THE STANDARDS LABORATORY WAS TO ENSURE AND IMPLEMENT A SYSTEM OF QUALITY CONTROL FOR INCOMING MATERIALS USED IN MANUFACTURING PROCESSES. SEVERAL ENGINEERING CONTROLS WERE USED TO ASSURE ACCURACY OF THE CALIBRATION PROCESSES INCLUDING: FLEX-FREE GRANITE TABLES, AIR LOCKED DOORS, TEMPERATURE CONTROLS, AND A SUPER-CLEAN ENVIRONMENT - Rocky Flats Plant, Standards Laboratory, Immediately north of 215A water tower & adjacent to Third Street, Golden, Jefferson County, CO

Global Access-controlled Transfer e-frame (GATe)

DOE Office of Scientific and Technical Information (OSTI.GOV)

2012-05-30

Global Access-controlled Transfer e-frame (GATe) was designed to take advantage of the patterns that occur during an electronic record transfer process. The e-frame (or electronic framework or platform) is the foundation for developing secure information transfer to meet classified and unclassified business processes and is particularly useful when there is a need to share information with various entities in a controlled and secure environment. It can share, search, upload, download and retrieve sensitive information, as well as provides reporting capabilities.

Fed-batch control based upon the measurement of intracellular NADH

NASA Technical Reports Server (NTRS)

Armiger, W. B.; Lee, J. F.; Montalvo, L. M.; Forro, J. R.

1987-01-01

A series of experiments demonstrating that on-line measurements of intracellular NADH by culture fluorescence can be used to monitor and control the fermentation process are described. A distinct advantage of intercellular NADH measurements over other monitoring techniques such as pH and dissolved oxygen is that it directly measures real time events occurring within the cell rather than changes in the environment. When coupled with other measurement parameters, it can provide a finer degree of sophistication in process control.

A dynamic experimental study on the evaporative cooling performance of porous building materials

NASA Astrophysics Data System (ADS)

Zhang, Yu; Zhang, Lei; Meng, Qinglin; Feng, Yanshan; Chen, Yuanrui

2017-08-01

Conventional outdoor dynamic and indoor steady-state experiments have certain limitations in regard to investigating the evaporative cooling performance of porous building materials. The present study investigated the evaporative cooling performance of a porous building material using a special wind tunnel apparatus. First, the composition and control principles of the wind tunnel environment control system were elucidated. Then, the meteorological environment on a typical summer day in Guangzhou was reproduced in the wind tunnel and the evaporation process and thermal parameters of specimens composed of a porous building material were continuously measured. Finally, the experimental results were analysed to evaluate the accuracy of the wind tunnel environment control system, the heat budget of the external surface of the specimens and the total thermal resistance of the specimens and its uncertainty. The analysis results indicated that the normalized root-mean-square error between the measured value of each environmental parameter in the wind tunnel test section and the corresponding value input into the environment control system was <4%, indicating that the wind tunnel apparatus had relatively high accuracy in reproducing outdoor meteorological environments. In addition, the wet specimen could cumulatively consume approximately 80% of the shortwave radiation heat during the day, thereby reducing the temperature of the external surface and the heat flow on the internal surface of the specimen. Compared to the dry specimen, the total thermal resistance of the wet specimen was approximately doubled, indicating that the evaporation process of the porous building material could significantly improve the thermal insulation performance of the specimen.

Method to decrease loss of aluminum and magnesium melts

DOEpatents

Hryn, John N.; Pellin, Michael J.; Calaway, Jr., Wallis F.; Moore, Jerry F.; Krumdick, Gregory K.

2002-01-01

A method to minimize oxidation of metal during melting processes is provided, the method comprising placing solid phase metal into a furnace environ-ment, transforming the solid-phase metal into molten metal phase having a molten metal surface, and creating a barrier between the surface and the environment. Also provided is a method for isolating the surface of molten metal from its environment, the method comprising confining the molten metal to a controlled atmos-phere, and imposing a floating substrate between the surface and the atmosphere.

Quality Detection of Litchi Stored in Different Environments Using an Electronic Nose

PubMed Central

Xu, Sai; Lü, Enli; Lu, Huazhong; Zhou, Zhiyan; Wang, Yu; Yang, Jing; Wang, Yajuan

2016-01-01

The purpose of this paper was to explore the utility of an electronic nose to detect the quality of litchi fruit stored in different environments. In this study, a PEN3 electronic nose was adopted to test the storage time and hardness of litchi that were stored in three different types of environment (room temperature, refrigerator and controlled-atmosphere). After acquiring data about the hardness of the sample and from the electronic nose, linear discriminant analysis (LDA), canonical correlation analysis (CCA), BP neural network (BPNN) and BP neural network-partial least squares regression (BPNN-PLSR), were employed for data processing. The experimental results showed that the hardness of litchi fruits stored in all three environments decreased during storage. The litchi stored at room temperature had the fastest rate of decrease in hardness, followed by those stored in a refrigerator environment and under a controlled-atmosphere. LDA has a poor ability to classify the storage time of the three environments in which litchi was stored. BPNN can effectively recognize the storage time of litchi stored in a refrigerator and a controlled-atmosphere environment. However, the BPNN classification of the effect of room temperature storage on litchi was poor. CCA results show a significant correlation between electronic nose data and hardness data under the room temperature, and the correlation is more obvious for those under the refrigerator environment and controlled-atmosphere environment. The BPNN-PLSR can effectively predict the hardness of litchi under refrigerator storage conditions and a controlled-atmosphere environment. However, the BPNN-PLSR prediction of the effect of room temperature storage on litchi and global environment storage on litchi were poor. Thus, this experiment proved that an electronic nose can detect the quality of litchi under refrigeratored storage and a controlled-atmosphere environment. These results provide a useful reference for future studies on nondestructive and intelligent monitoring of fruit quality. PMID:27338391

Research and development program in fiber optic sensors and distributed sensing for high temperature harsh environment energy applications (Conference Presentation)

NASA Astrophysics Data System (ADS)

Romanosky, Robert R.

2017-05-01

he National Energy Technology Laboratory (NETL) under the Department of Energy (DOE) Fossil Energy (FE) Program is leading the effort to not only develop near zero emission power generation systems, but to increaser the efficiency and availability of current power systems. The overarching goal of the program is to provide clean affordable power using domestic resources. Highly efficient, low emission power systems can have extreme conditions of high temperatures up to 1600 oC, high pressures up to 600 psi, high particulate loadings, and corrosive atmospheres that require monitoring. Sensing in these harsh environments can provide key information that directly impacts process control and system reliability. The lack of suitable measurement technology serves as a driver for the innovations in harsh environment sensor development. Advancements in sensing using optical fibers are key efforts within NETL's sensor development program as these approaches offer the potential to survive and provide critical information about these processes. An overview of the sensor development supported by the National Energy Technology Laboratory (NETL) will be given, including research in the areas of sensor materials, designs, and measurement types. New approaches to intelligent sensing, sensor placement and process control using networked sensors will be discussed as will novel approaches to fiber device design concurrent with materials development research and development in modified and coated silica and sapphire fiber based sensors. The use of these sensors for both single point and distributed measurements of temperature, pressure, strain, and a select suite of gases will be addressed. Additional areas of research includes novel control architecture and communication frameworks, device integration for distributed sensing, and imaging and other novel approaches to monitoring and controlling advanced processes. The close coupling of the sensor program with process modeling and control will be discussed for the overarching goal of clean power production.

An approach for investigation of secure access processes at a combined e-learning environment

NASA Astrophysics Data System (ADS)

Romansky, Radi; Noninska, Irina

2017-12-01

The article discuses an approach to investigate processes for regulation the security and privacy control at a heterogenous e-learning environment realized as a combination of traditional and cloud means and tools. Authors' proposal for combined architecture of e-learning system is presented and main subsystems and procedures are discussed. A formalization of the processes for using different types resources (public, private internal and private external) is proposed. The apparatus of Markovian chains (MC) is used for modeling and analytical investigation of the secure access to the resources is used and some assessments are presented.

Vacuum mechatronics

NASA Technical Reports Server (NTRS)

Hackwood, Susan; Belinski, Steven E.; Beni, Gerardo

1989-01-01

The discipline of vacuum mechatronics is defined as the design and development of vacuum-compatible computer-controlled mechanisms for manipulating, sensing and testing in a vacuum environment. The importance of vacuum mechatronics is growing with an increased application of vacuum in space studies and in manufacturing for material processing, medicine, microelectronics, emission studies, lyophylisation, freeze drying and packaging. The quickly developing field of vacuum mechatronics will also be the driving force for the realization of an advanced era of totally enclosed clean manufacturing cells. High technology manufacturing has increasingly demanding requirements for precision manipulation, in situ process monitoring and contamination-free environments. To remove the contamination problems associated with human workers, the tendency in many manufacturing processes is to move towards total automation. This will become a requirement in the near future for e.g., microelectronics manufacturing. Automation in ultra-clean manufacturing environments is evolving into the concept of self-contained and fully enclosed manufacturing. A Self Contained Automated Robotic Factory (SCARF) is being developed as a flexible research facility for totally enclosed manufacturing. The construction and successful operation of a SCARF will provide a novel, flexible, self-contained, clean, vacuum manufacturing environment. SCARF also requires very high reliability and intelligent control. The trends in vacuum mechatronics and some of the key research issues are reviewed.

Open Integrated Personal Learning Environment: Towards a New Conception of the ICT-Based Learning Processes

NASA Astrophysics Data System (ADS)

Conde, Miguel Ángel; García-Peñalvo, Francisco José; Casany, Marià José; Alier Forment, Marc

Learning processes are changing related to technological and sociological evolution, taking this in to account, a new learning strategy must be considered. Specifically what is needed is to give an effective step towards the eLearning 2.0 environments consolidation. This must imply the fusion of the advantages of the traditional LMS (Learning Management System) - more formative program control and planning oriented - with the social learning and the flexibility of the web 2.0 educative applications.

40 CFR 63.765 - Glycol dehydration unit process vent standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 11 2013-07-01 2013-07-01 false Glycol dehydration unit process vent... Facilities § 63.765 Glycol dehydration unit process vent standards. (a) This section applies to each glycol dehydration unit subject to this subpart that must be controlled for air emissions as specified in either...

40 CFR 63.765 - Glycol dehydration unit process vent standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 11 2014-07-01 2014-07-01 false Glycol dehydration unit process vent... Facilities § 63.765 Glycol dehydration unit process vent standards. (a) This section applies to each glycol dehydration unit subject to this subpart that must be controlled for air emissions as specified in either...

Timeliner: Automating Procedures on the ISS

NASA Technical Reports Server (NTRS)

Brown, Robert; Braunstein, E.; Brunet, Rick; Grace, R.; Vu, T.; Zimpfer, Doug; Dwyer, William K.; Robinson, Emily

2002-01-01

Timeliner has been developed as a tool to automate procedural tasks. These tasks may be sequential tasks that would typically be performed by a human operator, or precisely ordered sequencing tasks that allow autonomous execution of a control process. The Timeliner system includes elements for compiling and executing sequences that are defined in the Timeliner language. The Timeliner language was specifically designed to allow easy definition of scripts that provide sequencing and control of complex systems. The execution environment provides real-time monitoring and control based on the commands and conditions defined in the Timeliner language. The Timeliner sequence control may be preprogrammed, compiled from Timeliner "scripts," or it may consist of real-time, interactive inputs from system operators. In general, the Timeliner system lowers the workload for mission or process control operations. In a mission environment, scripts can be used to automate spacecraft operations including autonomous or interactive vehicle control, performance of preflight and post-flight subsystem checkouts, or handling of failure detection and recovery. Timeliner may also be used for mission payload operations, such as stepping through pre-defined procedures of a scientific experiment.

TOXIC METAL EMISSIONS FROM INCINERATION: MECHANISMS AND CONTROL

EPA Science Inventory

Toxic metals appear in the effluents of many combustion processes, and their release into the environment has come under regulatory scrutiny. This paper reviews the nature of the problems associated with toxic metals in combustion processes, and describes where these problems occ...

40 CFR 710.1 - Scope and compliance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 710.1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT TSCA CHEMICAL INVENTORY REGULATIONS General Provisions § 710.1 Scope and compliance. (a) This part... process chemical substances for commercial purposes under section 8(a) of the Toxic Substances Control Act...

Project Portfolio Management for Academic Libraries: A Gentle Introduction

ERIC Educational Resources Information Center

Vinopal, Jennifer

2012-01-01

In highly dynamic, service-oriented environments like academic libraries, much staff time is spent on initiatives to implement new products and services to meet users' evolving needs. Yet even in an environment where a sound project management process is applied, if we're not properly planning, managing, and controlling the organization's work in…

Air Traffic Complexity Measurement Environment (ACME): Software User's Guide

NASA Technical Reports Server (NTRS)

1996-01-01

A user's guide for the Air Traffic Complexity Measurement Environment (ACME) software is presented. The ACME consists of two major components, a complexity analysis tool and user interface. The Complexity Analysis Tool (CAT) analyzes complexity off-line, producing data files which may be examined interactively via the Complexity Data Analysis Tool (CDAT). The Complexity Analysis Tool is composed of three independently executing processes that communicate via PVM (Parallel Virtual Machine) and Unix sockets. The Runtime Data Management and Control process (RUNDMC) extracts flight plan and track information from a SAR input file, and sends the information to GARP (Generate Aircraft Routes Process) and CAT (Complexity Analysis Task). GARP in turn generates aircraft trajectories, which are utilized by CAT to calculate sector complexity. CAT writes flight plan, track and complexity data to an output file, which can be examined interactively. The Complexity Data Analysis Tool (CDAT) provides an interactive graphic environment for examining the complexity data produced by the Complexity Analysis Tool (CAT). CDAT can also play back track data extracted from System Analysis Recording (SAR) tapes. The CDAT user interface consists of a primary window, a controls window, and miscellaneous pop-ups. Aircraft track and position data is displayed in the main viewing area of the primary window. The controls window contains miscellaneous control and display items. Complexity data is displayed in pop-up windows. CDAT plays back sector complexity and aircraft track and position data as a function of time. Controls are provided to start and stop playback, adjust the playback rate, and reposition the display to a specified time.

Frontal Alpha Oscillations and Attentional Control: A Virtual Reality Neurofeedback Study.

PubMed

Berger, Anna M; Davelaar, Eddy J

2018-05-15

Two competing views about alpha oscillations suggest that cortical alpha reflect either cortical inactivity or cortical processing efficiency. We investigated the role of alpha oscillations in attentional control, as measured with a Stroop task. We used neurofeedback to train 22 participants to increase their level of alpha amplitude. Based on the conflict/control loop theory, we selected to train prefrontal alpha and focus on the Gratton effect as an index of deployment of attentional control. We expected an increase or a decrease in the Gratton effect with increase in neural learning depending on whether frontal alpha oscillations reflect cortical idling or enhanced processing efficiency, respectively. In order to induce variability in neural learning beyond natural occurring individual differences, we provided half of the participants with feedback on alpha amplitude in a 3-dimensional (3D) virtual reality environment and the other half received feedback in a 2D environment. Our results showed variable neural learning rates, with larger rates in the 3D compared to the 2D group, corroborating prior evidence of individual differences in EEG-based learning and the influence of a virtual environment. Regression analyses revealed a significant association between the learning rate and changes on deployment of attentional control, with larger learning rates being associated with larger decreases in the Gratton effect. This association was not modulated by feedback medium. The study supports the view of frontal alpha oscillations being associated with efficient neurocognitive processing and demonstrates the utility of neurofeedback training in addressing theoretical questions in the non-neurofeedback literature. Copyright © 2017 IBRO. Published by Elsevier Ltd. All rights reserved.

Measurement science and manufacturing science research

NASA Technical Reports Server (NTRS)

Phillips, D. Howard

1987-01-01

The research program of Semiconductor Research Corp. is managed as three overlapping areas: Manufacturing Sciences, Design Sciences and Microstructure Sciences. A total of 40 universities are participating in the performance of over 200 research tasks. The goals and direction of Manufacturing Sciences research became more clearly focused through the efforts of the Manufacturing Sciences Committee of the SRC Technical Advisory Board (TAB). The mission of the SRC Manufacturing Research is the quantification, control, and understanding of semiconductor manufacturing process necessary to achieve a predictable and profitable product output in the competitive environment of the next decade. The 1994 integrated circuit factory must demonstrate a three level hierarchy of control: (1) operation control, (2) process control, and (3) process design. These levels of control are briefly discussed.

Research into language concepts for the mission control center

NASA Technical Reports Server (NTRS)

Dellenback, Steven W.; Barton, Timothy J.; Ratner, Jeremiah M.

1990-01-01

A final report is given on research into language concepts for the Mission Control Center (MCC). The Specification Driven Language research is described. The state of the image processing field and how image processing techniques could be applied toward automating the generation of the language known as COmputation Development Environment (CODE or Comp Builder) are discussed. Also described is the development of a flight certified compiler for Comps.

The Use of Statistical Process Control-Charts for Person-Fit Analysis on Computerized Adaptive Testing. LSAC Research Report Series.

ERIC Educational Resources Information Center

Meijer, Rob R.; van Krimpen-Stoop, Edith M. L. A.

In this study a cumulative-sum (CUSUM) procedure from the theory of Statistical Process Control was modified and applied in the context of person-fit analysis in a computerized adaptive testing (CAT) environment. Six person-fit statistics were proposed using the CUSUM procedure, and three of them could be used to investigate the CAT in online test…

Computer-Mediated Group Processes in Distributed Command and Control Systems

DTIC Science & Technology

1988-06-01

Linville, "Michael J. Liebhaber, and Richard W. Obermayer Vreuls Corporation Jon J. Fallesen Army Research Institute DTIC SELECTEr • AUG I 1. 1988 ARI...control staffs who will operate in a computer- mediated environment. The Army Research Institute has initiated research to examine selected issues...computar-mediated group processes is needed. Procedure: The identification and selection of key research issues followed a three- step procedure. Previous

Challenges to a blow/fill/seal process with airborne microorganisms having different resistances to dry heat.

PubMed

Poisson, Patrick; Sinclair, Colin S; Tallentire, Alan

2006-01-01

Controlled challenges with air dispersed microorganisms having widely different resistances to dry heat, carried out on 624 BFS machine processing growth medium, have shown that higher the heat resistance, the greater the extent of vial contamination. Differences in heat resistance affected also the extent of vial contamination when parison and vial formation were knowingly manipulated through changes made to each of three process variables, provision of ballooning air, mould vacuum delay, and parison extrusion rate. The findings demonstrate that, in this investigational system, exposure of challenge micoorganisms to heat inherent in the process has a controlling influence on vial contamination, an influence that could also control microbiological risk in production environments.

The impact of the natural environment on the promotion of active living: an integrative systematic review.

PubMed

Calogiuri, Giovanna; Chroni, Stiliani

2014-08-24

An understanding of how the living environment influences physical activity (PA) is of great importance for health promotion. Researchers have reported increased PA when there is a greater availability of nature within people's living environment. However, little has been said about underlying motivational processes. The aim of this study was to review the existing literature on the relationship between the natural environment (NE) and PA, integrating it into a conceptual model that depicts the motivational process underlying this relationship. Through a systematic literature search in line with PRISMA guidelines, peer-reviewed articles were sought using PubMed (search updated to October 2013) and scrutiny of reference lists. In addition, we contacted experts within our network. We reviewed papers in which the research question(s) concerned: 1) Effects of PA in NE on individuals' feelings and beliefs; 2) Relationships between PA and availability of NEs; and 3) Motivational processes underlying visits to NEs in association with PA. Analysis and integration of the 90 selected studies were performed using the theory of planned behaviour (TPB). People's experiences in using the NE can enhance attitudes toward PA and perceived behavioural control via positive psychological states and stress-relieving effects, which lead to firmer intentions to engage in PA. Individual and environmental barriers, as expressions of social support and actual behavioural control, impact the process via subjective norm and perceived behavioural control. Instrumental beliefs such as a desire to enjoy nature and the expected health benefits also influence the process via attitudes. Different patterns have been identified for neighbourhood-based PA and outdoor recreations that take place in a NE. The availability of a NE and attractive views of nature within an individual's living environment are important contributors to PA, yet attention should focus on personal characteristics and environmental barriers. Policy and infrastructural interventions should aim to guarantee access and maintenance of the NE, as well as information and programming of social activities. Social campaigns via media and health institutions should highlight how nature can be a source of motivation for maintaining a PA routine, reducing stress and achieving aesthetic and health goals.

Implicit Processing of Visual Emotions Is Affected by Sound-Induced Affective States and Individual Affective Traits

PubMed Central

Quarto, Tiziana; Blasi, Giuseppe; Pallesen, Karen Johanne; Bertolino, Alessandro; Brattico, Elvira

2014-01-01

The ability to recognize emotions contained in facial expressions are affected by both affective traits and states and varies widely between individuals. While affective traits are stable in time, affective states can be regulated more rapidly by environmental stimuli, such as music, that indirectly modulate the brain state. Here, we tested whether a relaxing or irritating sound environment affects implicit processing of facial expressions. Moreover, we investigated whether and how individual traits of anxiety and emotional control interact with this process. 32 healthy subjects performed an implicit emotion processing task (presented to subjects as a gender discrimination task) while the sound environment was defined either by a) a therapeutic music sequence (MusiCure), b) a noise sequence or c) silence. Individual changes in mood were sampled before and after the task by a computerized questionnaire. Additionally, emotional control and trait anxiety were assessed in a separate session by paper and pencil questionnaires. Results showed a better mood after the MusiCure condition compared with the other experimental conditions and faster responses to happy faces during MusiCure compared with angry faces during Noise. Moreover, individuals with higher trait anxiety were faster in performing the implicit emotion processing task during MusiCure compared with Silence. These findings suggest that sound-induced affective states are associated with differential responses to angry and happy emotional faces at an implicit stage of processing, and that a relaxing sound environment facilitates the implicit emotional processing in anxious individuals. PMID:25072162

The MITy micro-rover: Sensing, control, and operation

NASA Technical Reports Server (NTRS)

Malafeew, Eric; Kaliardos, William

1994-01-01

The sensory, control, and operation systems of the 'MITy' Mars micro-rover are discussed. It is shown that the customized sun tracker and laser rangefinder provide internal, autonomous dead reckoning and hazard detection in unstructured environments. The micro-rover consists of three articulated platforms with sensing, processing and payload subsystems connected by a dual spring suspension system. A reactive obstacle avoidance routine makes intelligent use of robot-centered laser information to maneuver through cluttered environments. The hazard sensors include a rangefinder, inclinometers, proximity sensors and collision sensors. A 486/66 laptop computer runs the graphical user interface and programming environment. A graphical window displays robot telemetry in real time and a small TV/VCR is used for real time supervisory control. Guidance, navigation, and control routines work in conjunction with the mapping and obstacle avoidance functions to provide heading and speed commands that maneuver the robot around obstacles and towards the target.

Power control of SAFE reactor using fuzzy logic

NASA Astrophysics Data System (ADS)

Irvine, Claude

2002-01-01

Controlling the 100 kW SAFE (Safe Affordable Fission Engine) reactor consists of design and implementation of a fuzzy logic process control system to regulate dynamic variables related to nuclear system power. The first phase of development concentrates primarily on system power startup and regulation, maintaining core temperature equilibrium, and power profile matching. This paper discusses the experimental work performed in those areas. Nuclear core power from the fuel elements is simulated using resistive heating elements while heat rejection is processed by a series of heat pipes. Both axial and radial nuclear power distributions are determined from neuronic modeling codes. The axial temperature profile of the simulated core is matched to the nuclear power profile by varying the resistance of the heating elements. The SAFE model establishes radial temperature profile equivalence by establishing 32 control zones as the nodal coordinates. Control features also allow for slow warm up, since complete shutoff can occur in the heat pipes if heat-source temperatures drop/rise below a certain minimum value, depending on the specific fluid and gas combination in the heat pipe. The entire system is expected to be self-adaptive, i.e., capable of responding to long-range changes in the space environment. Particular attention in the development of the fuzzy logic algorithm shall ensure that the system process remains at set point, virtually eliminating overshoot on start-up and during in-process disturbances. The controller design will withstand harsh environments and applications where it might come in contact with water, corrosive chemicals, radiation fields, etc. .

Bacteriophages for detection and control of bacterial pathogens in food and food-processing environment.

PubMed

Brovko, Lubov Y; Anany, Hany; Griffiths, Mansel W

2012-01-01

This chapter presents recent advances in bacteriophage research and their application in the area of food safety. Section 1 describes general facts on phage biology that are relevant to their application for control and detection of bacterial pathogens in food and environmental samples. Section 2 summarizes the recently acquired data on application of bacteriophages to control growth of bacterial pathogens and spoilage organisms in food and food-processing environment. Section 3 deals with application of bacteriophages for detection and identification of bacterial pathogens. Advantages of bacteriophage-based methods are presented and their shortcomings are discussed. The chapter is intended for food scientist and food product developers, and people in food inspection and health agencies with the ultimate goal to attract their attention to the new developing technology that has a tremendous potential in providing means for producing wholesome and safe food. Copyright © 2012 Elsevier Inc. All rights reserved.

Controlled English to facilitate human/machine analytical processing

NASA Astrophysics Data System (ADS)

Braines, Dave; Mott, David; Laws, Simon; de Mel, Geeth; Pham, Tien

2013-06-01

Controlled English is a human-readable information representation format that is implemented using a restricted subset of the English language, but which is unambiguous and directly accessible by simple machine processes. We have been researching the capabilities of CE in a number of contexts, and exploring the degree to which a flexible and more human-friendly information representation format could aid the intelligence analyst in a multi-agent collaborative operational environment; especially in cases where the agents are a mixture of other human users and machine processes aimed at assisting the human users. CE itself is built upon a formal logic basis, but allows users to easily specify models for a domain of interest in a human-friendly language. In our research we have been developing an experimental component known as the "CE Store" in which CE information can be quickly and flexibly processed and shared between human and machine agents. The CE Store environment contains a number of specialized machine agents for common processing tasks and also supports execution of logical inference rules that can be defined in the same CE language. This paper outlines the basic architecture of this approach, discusses some of the example machine agents that have been developed, and provides some typical examples of the CE language and the way in which it has been used to support complex analytical tasks on synthetic data sources. We highlight the fusion of human and machine processing supported through the use of the CE language and CE Store environment, and show this environment with examples of highly dynamic extensions to the model(s) and integration between different user-defined models in a collaborative setting.

Cognitive task load in a naval ship control centre: from identification to prediction.

PubMed

Grootjen, M; Neerincx, M A; Veltman, J A

Deployment of information and communication technology will lead to further automation of control centre tasks and an increasing amount of information to be processed. A method for establishing adequate levels of cognitive task load for the operators in such complex environments has been developed. It is based on a model distinguishing three load factors: time occupied, task-set switching, and level of information processing. Application of the method resulted in eight scenarios for eight extremes of task load (i.e. low and high values for each load factor). These scenarios were performed by 13 teams in a high-fidelity control centre simulator of the Royal Netherlands Navy. The results show that the method provides good prediction of the task load that will actually appear in the simulator. The model allowed identification of under- and overload situations showing negative effects on operator performance corresponding to controlled experiments in a less realistic task environment. Tools proposed to keep the operator at an optimum task load are (adaptive) task allocation and interface support.

Auditory Attentional Control and Selection during Cocktail Party Listening

PubMed Central

Hill, Kevin T.

2010-01-01

In realistic auditory environments, people rely on both attentional control and attentional selection to extract intelligible signals from a cluttered background. We used functional magnetic resonance imaging to examine auditory attention to natural speech under such high processing-load conditions. Participants attended to a single talker in a group of 3, identified by the target talker's pitch or spatial location. A catch-trial design allowed us to distinguish activity due to top-down control of attention versus attentional selection of bottom-up information in both the spatial and spectral (pitch) feature domains. For attentional control, we found a left-dominant fronto-parietal network with a bias toward spatial processing in dorsal precentral sulcus and superior parietal lobule, and a bias toward pitch in inferior frontal gyrus. During selection of the talker, attention modulated activity in left intraparietal sulcus when using talker location and in bilateral but right-dominant superior temporal sulcus when using talker pitch. We argue that these networks represent the sources and targets of selective attention in rich auditory environments. PMID:19574393

A Bayesian formulation of behavioral control.

PubMed

Huys, Quentin J M; Dayan, Peter

2009-12-01

Helplessness, a belief that the world is not subject to behavioral control, has long been central to our understanding of depression, and has influenced cognitive theories, animal models and behavioral treatments. However, despite its importance, there is no fully accepted definition of helplessness or behavioral control in psychology or psychiatry, and the formal treatments in engineering appear to capture only limited aspects of the intuitive concepts. Here, we formalize controllability in terms of characteristics of prior distributions over affectively charged environments. We explore the relevance of this notion of control to reinforcement learning methods of optimising behavior in such environments and consider how apparently maladaptive beliefs can result from normative inference processes. These results are discussed with reference to depression and animal models thereof.

QPA-CLIPS: A language and representation for process control

NASA Technical Reports Server (NTRS)

Freund, Thomas G.

1994-01-01

QPA-CLIPS is an extension of CLIPS oriented towards process control applications. Its constructs define a dependency network of process actions driven by sensor information. The language consists of three basic constructs: TASK, SENSOR, and FILTER. TASK's define the dependency network describing alternative state transitions for a process. SENSOR's and FILTER's define sensor information sources used to activate state transitions within the network. Deftemplate's define these constructs and their run-time environment is an interpreter knowledge base, performing pattern matching on sensor information and so activating TASK's in the dependency network. The pattern matching technique is based on the repeatable occurrence of a sensor data pattern. QPA-CIPS has been successfully tested on a SPARCStation providing supervisory control to an Allen-Bradley PLC 5 controller driving molding equipment.

Integrated orbit and attitude hardware-in-the-loop simulations for autonomous satellite formation flying

NASA Astrophysics Data System (ADS)

Park, Han-Earl; Park, Sang-Young; Kim, Sung-Woo; Park, Chandeok

2013-12-01

Development and experiment of an integrated orbit and attitude hardware-in-the-loop (HIL) simulator for autonomous satellite formation flying are presented. The integrated simulator system consists of an orbit HIL simulator for orbit determination and control, and an attitude HIL simulator for attitude determination and control. The integrated simulator involves four processes (orbit determination, orbit control, attitude determination, and attitude control), which interact with each other in the same way as actual flight processes do. Orbit determination is conducted by a relative navigation algorithm using double-difference GPS measurements based on the extended Kalman filter (EKF). Orbit control is performed by a state-dependent Riccati equation (SDRE) technique that is utilized as a nonlinear controller for the formation control problem. Attitude is determined from an attitude heading reference system (AHRS) sensor, and a proportional-derivative (PD) feedback controller is used to control the attitude HIL simulator using three momentum wheel assemblies. Integrated orbit and attitude simulations are performed for a formation reconfiguration scenario. By performing the four processes adequately, the desired formation reconfiguration from a baseline of 500-1000 m was achieved with meter-level position error and millimeter-level relative position navigation. This HIL simulation demonstrates the performance of the integrated HIL simulator and the feasibility of the applied algorithms in a real-time environment. Furthermore, the integrated HIL simulator system developed in the current study can be used as a ground-based testing environment to reproduce possible actual satellite formation operations.

Physical Processes and Real-Time Chemical Measurement of the Insect Olfactory Environment

PubMed Central

Abrell, Leif; Hildebrand, John G.

2009-01-01

Odor-mediated insect navigation in airborne chemical plumes is vital to many ecological interactions, including mate finding, flower nectaring, and host locating (where disease transmission or herbivory may begin). After emission, volatile chemicals become rapidly mixed and diluted through physical processes that create a dynamic olfactory environment. This review examines those physical processes and some of the analytical technologies available to characterize those behavior-inducing chemical signals at temporal scales equivalent to the olfactory processing in insects. In particular, we focus on two areas of research that together may further our understanding of olfactory signal dynamics and its processing and perception by insects. First, measurement of physical atmospheric processes in the field can provide insight into the spatiotemporal dynamics of the odor signal available to insects. Field measurements in turn permit aspects of the physical environment to be simulated in the laboratory, thereby allowing careful investigation into the links between odor signal dynamics and insect behavior. Second, emerging analytical technologies with high recording frequencies and field-friendly inlet systems may offer new opportunities to characterize natural odors at spatiotemporal scales relevant to insect perception and behavior. Characterization of the chemical signal environment allows the determination of when and where olfactory-mediated behaviors may control ecological interactions. Finally, we argue that coupling of these two research areas will foster increased understanding of the physicochemical environment and enable researchers to determine how olfactory environments shape insect behaviors and sensory systems. PMID:18548311

Theory of "laser distillation" of enantiomers: purification of a racemic mixture of randomly oriented dimethylallene in a collisional environment.

PubMed

Gerbasi, David; Shapiro, Moshe; Brumer, Paul

2006-02-21

Enantiomeric control of 1,3 dimethylallene in a collisional environment is examined. Specifically, our previous "laser distillation" scenario wherein three perpendicular linearly polarized light fields are applied to excite a set of vib-rotational eigenstates of a randomly oriented sample is considered. The addition of internal conversion, dissociation, decoherence, and collisional relaxation mimics experimental conditions and molecular decay processes. Of greatest relevance is internal conversion which, in the case of dimethylallene, is followed by molecular dissociation. For various rates of internal conversion, enantiomeric control is maintained in this scenario by a delicate balance between collisional relaxation of excited dimethylallene that enhances control and collisional dephasing, which diminishes control.

Microfluidic Experiments Studying Pore Scale Interactions of Microbes and Geochemistry

NASA Astrophysics Data System (ADS)

Chen, M.; Kocar, B. D.

2016-12-01

Understanding how physical phenomena, chemical reactions, and microbial behavior interact at the pore-scale is crucial to understanding larger scale trends in groundwater chemistry. Recent studies illustrate the utility of microfluidic devices for illuminating pore-scale physical-biogeochemical processes and their control(s) on the cycling of iron, uranium, and other important elements 1-3. These experimental systems are ideal for examining geochemical reactions mediated by microbes, which include processes governed by complex biological phenomenon (e.g. biofilm formation, etc.)4. We present results of microfluidic experiments using a model metal reducing bacteria and varying pore geometries, exploring the limitations of the microorganisms' ability to access tight pore spaces, and examining coupled biogeochemical-physical controls on the cycling of redox sensitive metals. Experimental results will provide an enhanced understanding of coupled physical-biogeochemical processes transpiring at the pore-scale, and will constrain and compliment continuum models used to predict and describe the subsurface cycling of redox-sensitive elements5. 1. Vrionis, H. A. et al. Microbiological and geochemical heterogeneity in an in situ uranium bioremediation field site. Appl. Environ. Microbiol. 71, 6308-6318 (2005). 2. Pearce, C. I. et al. Pore-scale characterization of biogeochemical controls on iron and uranium speciation under flow conditions. Environ. Sci. Technol. 46, 7992-8000 (2012). 3. Zhang, C., Liu, C. & Shi, Z. Micromodel investigation of transport effect on the kinetics of reductive dissolution of hematite. Environ. Sci. Technol. 47, 4131-4139 (2013). 4. Ginn, T. R. et al. Processes in microbial transport in the natural subsurface. Adv. Water Resour. 25, 1017-1042 (2002). 5. Scheibe, T. D. et al. Coupling a genome-scale metabolic model with a reactive transport model to describe in situ uranium bioremediation. Microb. Biotechnol. 2, 274-286 (2009).

A Framework for WWW Query Processing

NASA Technical Reports Server (NTRS)

Wu, Binghui Helen; Wharton, Stephen (Technical Monitor)

2000-01-01

Query processing is the most common operation in a DBMS. Sophisticated query processing has been mainly targeted at a single enterprise environment providing centralized control over data and metadata. Submitting queries by anonymous users on the web is different in such a way that load balancing or DBMS' accessing control becomes the key issue. This paper provides a solution by introducing a framework for WWW query processing. The success of this framework lies in the utilization of query optimization techniques and the ontological approach. This methodology has proved to be cost effective at the NASA Goddard Space Flight Center Distributed Active Archive Center (GDAAC).

Ochrobactrum anthropi used to control ammonium for nitrate removal by starch-stabilized nanoscale zero valent iron.

PubMed

Zhou, Jun; Sun, Qianyu; Chen, Dan; Wang, Hongyu; Yang, Kai

2017-10-01

In this study, the hydrogenotrophic denitrifying bacterium Ochrobactrum anthropi was added in to the process of nitrate removal by starch-stabilized nanoscale zero valent iron (nZVI) to minimize undesirable ammonium. The ammonium control performance and cooperative mechanism of this combined process were investigated, and batch experiments were conducted to discuss the effects of starch-stabilized nZVI dose, biomass, and pH on nitrate reduction and ammonium control of this system. The combined system achieved satisfactory performance because the anaerobic iron corrosion process generates H 2 , which is used as an electron donor for the autohydrogenotrophic bacterium Ochrobactrum anthropi to achieve the autohydrogenotrophic denitrification process converting nitrate to N 2 . When starch-stabilized nZVI dose was increased from 0.5 to 2.0 g/L, nitrate reduction rate gradually increased, and ammonium yield also increased from 9.40 to 60.51 mg/L. Nitrate removal rate gradually decreased and ammonium yield decreased from 14.93 to 2.61 mg/L with initial OD 600 increasing from 0.015 to 0.080. The abiotic Fe 0 reduction process played a key role in nitrate removal in an acidic environment and generated large amounts of ammonium. Meanwhile, the nitrate removal rate decreased and ammonium yield also reduced in an alkaline environment.

Self-assembled materials and supramolecular chemistry within microfluidic environments: from common thermodynamic states to non-equilibrium structures.

PubMed

Sevim, S; Sorrenti, A; Franco, C; Furukawa, S; Pané, S; deMello, A J; Puigmartí-Luis, J

2018-05-01

Self-assembly is a crucial component in the bottom-up fabrication of hierarchical supramolecular structures and advanced functional materials. Control has traditionally relied on the use of encoded building blocks bearing suitable moieties for recognition and interaction, with targeting of the thermodynamic equilibrium state. On the other hand, nature leverages the control of reaction-diffusion processes to create hierarchically organized materials with surprisingly complex biological functions. Indeed, under non-equilibrium conditions (kinetic control), the spatio-temporal command of chemical gradients and reactant mixing during self-assembly (the creation of non-uniform chemical environments for example) can strongly affect the outcome of the self-assembly process. This directly enables a precise control over material properties and functions. In this tutorial review, we show how the unique physical conditions offered by microfluidic technologies can be advantageously used to control the self-assembly of materials and of supramolecular aggregates in solution, making possible the isolation of intermediate states and unprecedented non-equilibrium structures, as well as the emergence of novel functions. Selected examples from the literature will be used to confirm that microfluidic devices are an invaluable toolbox technology for unveiling, understanding and steering self-assembly pathways to desired structures, properties and functions, as well as advanced processing tools for device fabrication and integration.

Chemometrics-based process analytical technology (PAT) tools: applications and adaptation in pharmaceutical and biopharmaceutical industries.

PubMed

Challa, Shruthi; Potumarthi, Ravichandra

2013-01-01

Process analytical technology (PAT) is used to monitor and control critical process parameters in raw materials and in-process products to maintain the critical quality attributes and build quality into the product. Process analytical technology can be successfully implemented in pharmaceutical and biopharmaceutical industries not only to impart quality into the products but also to prevent out-of-specifications and improve the productivity. PAT implementation eliminates the drawbacks of traditional methods which involves excessive sampling and facilitates rapid testing through direct sampling without any destruction of sample. However, to successfully adapt PAT tools into pharmaceutical and biopharmaceutical environment, thorough understanding of the process is needed along with mathematical and statistical tools to analyze large multidimensional spectral data generated by PAT tools. Chemometrics is a chemical discipline which incorporates both statistical and mathematical methods to obtain and analyze relevant information from PAT spectral tools. Applications of commonly used PAT tools in combination with appropriate chemometric method along with their advantages and working principle are discussed. Finally, systematic application of PAT tools in biopharmaceutical environment to control critical process parameters for achieving product quality is diagrammatically represented.

I control therefore I do: judgments of agency influence action selection.

PubMed

Karsh, N; Eitam, B

2015-05-01

Our sense of being agents, that is of willingly controlling both our own bodies and the external environment is ubiquitous if thin. Empirical and theoretical work on this 'sense of agency' has documented motivational, cognitive and neural influences on implicit (out of awareness) and explicit (conscious) judgments of agency. For example, fluency of action selection processes has been recently shown to affect judgments of one's degree of control over an external event. However, it is an open question whether and how such judgments of agency act as input to other processes. In this study we demonstrate that the opposite relationship between action selection and judgment of agency also exists. Specifically, we show that manipulating one's objective control over the environment influences both the speed and the frequency of performing an action associated with that control. This pattern bears a striking resemblance to the effect that tangible rewards have on action selection and suggests that positive control feedback is rewarding to the organism, consequently affecting action selection. If further corroborated this 'reward from control' may explain everyday addictions such as prolonged engagement in arcade games and pathological behaviors, such as stereotypy. Copyright © 2015 Elsevier B.V. All rights reserved.

Neuromechanics: an integrative approach for understanding motor control.

PubMed

Nishikawa, Kiisa; Biewener, Andrew A; Aerts, Peter; Ahn, Anna N; Chiel, Hillel J; Daley, Monica A; Daniel, Thomas L; Full, Robert J; Hale, Melina E; Hedrick, Tyson L; Lappin, A Kristopher; Nichols, T Richard; Quinn, Roger D; Satterlie, Richard A; Szymik, Brett

2007-07-01

Neuromechanics seeks to understand how muscles, sense organs, motor pattern generators, and brain interact to produce coordinated movement, not only in complex terrain but also when confronted with unexpected perturbations. Applications of neuromechanics include ameliorating human health problems (including prosthesis design and restoration of movement following brain or spinal cord injury), as well as the design, actuation and control of mobile robots. In animals, coordinated movement emerges from the interplay among descending output from the central nervous system, sensory input from body and environment, muscle dynamics, and the emergent dynamics of the whole animal. The inevitable coupling between neural information processing and the emergent mechanical behavior of animals is a central theme of neuromechanics. Fundamentally, motor control involves a series of transformations of information, from brain and spinal cord to muscles to body, and back to brain. The control problem revolves around the specific transfer functions that describe each transformation. The transfer functions depend on the rules of organization and operation that determine the dynamic behavior of each subsystem (i.e., central processing, force generation, emergent dynamics, and sensory processing). In this review, we (1) consider the contributions of muscles, (2) sensory processing, and (3) central networks to motor control, (4) provide examples to illustrate the interplay among brain, muscles, sense organs and the environment in the control of movement, and (5) describe advances in both robotics and neuromechanics that have emerged from application of biological principles in robotic design. Taken together, these studies demonstrate that (1) intrinsic properties of muscle contribute to dynamic stability and control of movement, particularly immediately after perturbations; (2) proprioceptive feedback reinforces these intrinsic self-stabilizing properties of muscle; (3) control systems must contend with inevitable time delays that can simplify or complicate control; and (4) like most animals under a variety of circumstances, some robots use a trial and error process to tune central feedforward control to emergent body dynamics.

The Interplay between Information and Control Theory within Interactive Decision-Making Problems

ERIC Educational Resources Information Center

Gorantla, Siva Kumar

2012-01-01

The context for this work is two-agent team decision systems. An "agent" is an intelligent entity that can measure some aspect of its environment, process information and possibly influence the environment through its action. In a collaborative two-agent team decision system, the agents can be coupled by noisy or noiseless interactions…

78 FR 6269 - Amendment to the International Traffic in Arms Regulations: Revision of U.S. Munitions List...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-30

... remain subject to USML control are modeling or simulation tools that model or simulate the environments... USML revision process, the public is asked to provide specific examples of nuclear-related items whose...) Modeling or simulation tools that model or simulate the environments generated by nuclear detonations or...

Hyporheic exchange in mountain rivers II: Effects of channel morphology on mechanics, scales, and rates of exchange

Treesearch

John M. Buffington; Daniele Tonina

2009-01-01

We propose that the mechanisms driving hyporheic exchange vary systematically with different channel morphologies and associated fluvial processes that occur in mountain basins, providing a framework for examining physical controls on hyporheic environments and their spatial variation across the landscape. Furthermore, the spatial distribution of hyporheic environments...

40 CFR 429.52 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... technology (BCT). [Reserved] 429.52 Section 429.52 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Dry Process... by the application of the best conventional pollutant control technology (BCT). [Reserved] ...

Levels of integration in cognitive control and sequence processing in the prefrontal cortex.

PubMed

Bahlmann, Jörg; Korb, Franziska M; Gratton, Caterina; Friederici, Angela D

2012-01-01

Cognitive control is necessary to flexibly act in changing environments. Sequence processing is needed in language comprehension to build the syntactic structure in sentences. Functional imaging studies suggest that sequence processing engages the left ventrolateral prefrontal cortex (PFC). In contrast, cognitive control processes additionally recruit bilateral rostral lateral PFC regions. The present study aimed to investigate these two types of processes in one experimental paradigm. Sequence processing was manipulated using two different sequencing rules varying in complexity. Cognitive control was varied with different cue-sets that determined the choice of a sequencing rule. Univariate analyses revealed distinct PFC regions for the two types of processing (i.e. sequence processing: left ventrolateral PFC and cognitive control processing: bilateral dorsolateral and rostral PFC). Moreover, in a common brain network (including left lateral PFC and intraparietal sulcus) no interaction between sequence and cognitive control processing was observed. In contrast, a multivariate pattern analysis revealed an interaction of sequence and cognitive control processing, such that voxels in left lateral PFC and parietal cortex showed different tuning functions for tasks involving different sequencing and cognitive control demands. These results suggest that the difference between the process of rule selection (i.e. cognitive control) and the process of rule-based sequencing (i.e. sequence processing) find their neuronal underpinnings in distinct activation patterns in lateral PFC. Moreover, the combination of rule selection and rule sequencing can shape the response of neurons in lateral PFC and parietal cortex.

Levels of Integration in Cognitive Control and Sequence Processing in the Prefrontal Cortex

PubMed Central

Bahlmann, Jörg; Korb, Franziska M.; Gratton, Caterina; Friederici, Angela D.

2012-01-01

Cognitive control is necessary to flexibly act in changing environments. Sequence processing is needed in language comprehension to build the syntactic structure in sentences. Functional imaging studies suggest that sequence processing engages the left ventrolateral prefrontal cortex (PFC). In contrast, cognitive control processes additionally recruit bilateral rostral lateral PFC regions. The present study aimed to investigate these two types of processes in one experimental paradigm. Sequence processing was manipulated using two different sequencing rules varying in complexity. Cognitive control was varied with different cue-sets that determined the choice of a sequencing rule. Univariate analyses revealed distinct PFC regions for the two types of processing (i.e. sequence processing: left ventrolateral PFC and cognitive control processing: bilateral dorsolateral and rostral PFC). Moreover, in a common brain network (including left lateral PFC and intraparietal sulcus) no interaction between sequence and cognitive control processing was observed. In contrast, a multivariate pattern analysis revealed an interaction of sequence and cognitive control processing, such that voxels in left lateral PFC and parietal cortex showed different tuning functions for tasks involving different sequencing and cognitive control demands. These results suggest that the difference between the process of rule selection (i.e. cognitive control) and the process of rule-based sequencing (i.e. sequence processing) find their neuronal underpinnings in distinct activation patterns in lateral PFC. Moreover, the combination of rule selection and rule sequencing can shape the response of neurons in lateral PFC and parietal cortex. PMID:22952762

40 CFR 424.37 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... control technology. 424.37 Section 424.37 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS FERROALLOY MANUFACTURING POINT SOURCE CATEGORY Slag Processing... by the application of the best conventional pollutant control technology. Except as provided in...

40 CFR 436.182 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... technology currently available. 436.182 Section 436.182 Protection of Environment ENVIRONMENTAL PROTECTION... degree of effluent reduction attainable by the application of the best practicable control technology... best practicable control technology currently available (BPT): (1) Discharges of process generated...

40 CFR 436.32 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... technology currently available. 436.32 Section 436.32 Protection of Environment ENVIRONMENTAL PROTECTION... effluent reduction attainable by the application of the best practicable control technology currently... of the best practicable control technology currently available (BPT): (1) Discharges of process...

40 CFR 436.182 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... technology currently available. 436.182 Section 436.182 Protection of Environment ENVIRONMENTAL PROTECTION... degree of effluent reduction attainable by the application of the best practicable control technology... best practicable control technology currently available (BPT): (1) Discharges of process generated...

40 CFR 436.182 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... technology currently available. 436.182 Section 436.182 Protection of Environment ENVIRONMENTAL PROTECTION... degree of effluent reduction attainable by the application of the best practicable control technology... best practicable control technology currently available (BPT): (1) Discharges of process generated...

40 CFR 436.22 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... technology currently available. 436.22 Section 436.22 Protection of Environment ENVIRONMENTAL PROTECTION... reduction attainable by the application of the best practicable control technology currently available. (a... best practicable control technology currently available (BPT): (1) Discharges of process generated...

40 CFR 436.22 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... technology currently available. 436.22 Section 436.22 Protection of Environment ENVIRONMENTAL PROTECTION... reduction attainable by the application of the best practicable control technology currently available. (a... best practicable control technology currently available (BPT): (1) Discharges of process generated...

Identifying postural control and thresholds of instability utilizing a motion-based ATV simulator.

DOT National Transportation Integrated Search

2017-01-01

Our ATV simulator is currently the only one in existence that allows studies of human subjects engaged in active riding, a process that is necessary for ATV operators to perform in order to maintain vehicle control, in a virtual reality environ...

40 CFR 63.52 - Approval process for new and existing affected sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... affected sources. 63.52 Section 63.52 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... CATEGORIES Requirements for Control Technology Determinations for Major Sources in Accordance With Clean Air... emission reductions that can be achieved if the control technologies or work practices are installed...

Using OPC technology to support the study of advanced process control.

PubMed

Mahmoud, Magdi S; Sabih, Muhammad; Elshafei, Moustafa

2015-03-01

OPC, originally the Object Linking and Embedding (OLE) for Process Control, brings a broad communication opportunity between different kinds of control systems. This paper investigates the use of OPC technology for the study of distributed control systems (DCS) as a cost effective and flexible research tool for the development and testing of advanced process control (APC) techniques in university research centers. Co-Simulation environment based on Matlab, LabVIEW and TCP/IP network is presented here. Several implementation issues and OPC based client/server control application have been addressed for TCP/IP network. A nonlinear boiler model is simulated as OPC server and OPC client is used for closed loop model identification, and to design a Model Predictive Controller. The MPC is able to control the NOx emissions in addition to drum water level and steam pressure. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

A bio-inspired kinematic controller for obstacle avoidance during reaching tasks with real robots.

PubMed

Srinivasa, Narayan; Bhattacharyya, Rajan; Sundareswara, Rashmi; Lee, Craig; Grossberg, Stephen

2012-11-01

This paper describes a redundant robot arm that is capable of learning to reach for targets in space in a self-organized fashion while avoiding obstacles. Self-generated movement commands that activate correlated visual, spatial and motor information are used to learn forward and inverse kinematic control models while moving in obstacle-free space using the Direction-to-Rotation Transform (DIRECT). Unlike prior DIRECT models, the learning process in this work was realized using an online Fuzzy ARTMAP learning algorithm. The DIRECT-based kinematic controller is fault tolerant and can handle a wide range of perturbations such as joint locking and the use of tools despite not having experienced them during learning. The DIRECT model was extended based on a novel reactive obstacle avoidance direction (DIRECT-ROAD) model to enable redundant robots to avoid obstacles in environments with simple obstacle configurations. However, certain configurations of obstacles in the environment prevented the robot from reaching the target with purely reactive obstacle avoidance. To address this complexity, a self-organized process of mental rehearsals of movements was modeled, inspired by human and animal experiments on reaching, to generate plans for movement execution using DIRECT-ROAD in complex environments. These mental rehearsals or plans are self-generated by using the Fuzzy ARTMAP algorithm to retrieve multiple solutions for reaching each target while accounting for all the obstacles in its environment. The key aspects of the proposed novel controller were illustrated first using simple examples. Experiments were then performed on real robot platforms to demonstrate successful obstacle avoidance during reaching tasks in real-world environments. Copyright © 2012 Elsevier Ltd. All rights reserved.

Cognitive dissonance and the perception of natural environments.

PubMed

Balcetis, Emily; Dunning, David

2007-10-01

Two studies demonstrated that the motivation to resolve cognitive dissonance affects the visual perception of physical environments. In Study 1, subjects crossed a campus quadrangle wearing a costume reminiscent of Carmen Miranda. In Study 2, subjects pushed themselves up a hill while kneeling on a skateboard. Subjects performed either task under a high-choice, low-choice, or control condition. Subjects in the high-choice conditions, presumably to resolve dissonance, perceived the environment to be less aversive than did subjects in the low-choice and control conditions, seeing a shorter distance to travel (Study 1) and a shallower slope to climb (Study 2). These studies suggest that the impact of motivational states extends from social judgment down into perceptual processes.

Bubble Induced Disruption of a Planar Solid-Liquid Interface During Controlled Directional Solidification in a Microgravity Environment

NASA Technical Reports Server (NTRS)

Grugel, Richard N.; Brush, Lucien N.; Anilkumar, Amrutur V.

2013-01-01

Pore Formation and Mobility Investigation (PFMI) experiments were conducted in the microgravity environment aboard the International Space Station with the intent of better understanding the role entrained porosity/bubbles play during controlled directional solidification. The planar interface in a slowing growing succinonitrile - 0.24 wt% water alloy was being observed when a nitrogen bubble traversed the mushy zone and remained at the solid-liquid interface. Breakdown of the interface to shallow cells subsequently occurred, and was later evaluated using down-linked data from a nearby thermocouple. These results and other detrimental effects due to the presence of bubbles during solidification processing in a microgravity environment are presented and discussed.

Risk Identification in a Smart Monitoring System Used to Preserve Artefacts Based on Textile Materials

NASA Astrophysics Data System (ADS)

Diaconescu, V. D.; Scripcariu, L.; Mătăsaru, P. D.; Diaconescu, M. R.; Ignat, C. A.

2018-06-01

Exhibited textile-materials-based artefacts can be affected by the environmental conditions. A smart monitoring system that commands an adaptive automatic environment control system is proposed for indoor exhibition spaces containing various textile artefacts. All exhibited objects are monitored by many multi-sensor nodes containing temperature, relative humidity and light sensors. Data collected periodically from the entire sensor network is stored in a database and statistically processed in order to identify and classify the environment risk. Risk consequences are analyzed depending on the risk class and the smart system commands different control measures in order to stabilize the indoor environment conditions to the recommended values and prevent material degradation.

Exploration Flight Test 1 Afterbody Aerothermal Environment Reconstruction

NASA Technical Reports Server (NTRS)

Hyatt, Andrew J.; Oliver, Brandon; Amar, Adam; Lessard, Victor

2016-01-01

The Exploration Flight Test 1 vehicle included roughly 100 near surface thermocouples on the after body of the vehicle. The temperature traces at each of these instruments have been used to perform inverse environment reconstruction to determine the aerothermal environment experienced during re-entry of the vehicle. This paper provides an overview of the reconstructed environments and identifies critical aspects of the environment. These critical aspects include transition and reaction control system jet influence. A blind test of the process and reconstruction tool was also performed to build confidence in the reconstructed environments. Finally, an uncertainty quantification analysis was also performed to identify the impact of each of the uncertainties on the reconstructed environments.

Proceedings of the Lunar Materials Technology Symposium

NASA Technical Reports Server (NTRS)

1992-01-01

The meeting was organized around a possible lunar outpost scenario, featuring industrial technologies, systems, and components applicable to the extraction, processing, and fabrication of local materials. Acknowledged space resources experts as well as investigators from outside the field whose knowledge could be applied to space development activities were brought together. Presentations came from a variety of specialists in fields such as minerals processing, environmental control, and communications. The sessions of the symposium were divided into the following areas: resource characterization, energy management, materials processing, environment control, and automation and communications.

Automated system for the on-line monitoring of powder blending processes using near-infrared spectroscopy. Part I. System development and control.

PubMed

Hailey, P A; Doherty, P; Tapsell, P; Oliver, T; Aldridge, P K

1996-03-01

An automated system for the on-line monitoring of powder blending processes is described. The system employs near-infrared (NIR) spectroscopy using fibre-optics and a graphical user interface (GUI) developed in the LabVIEW environment. The complete supervisory control and data analysis (SCADA) software controls blender and spectrophotometer operation and performs statistical spectral data analysis in real time. A data analysis routine using standard deviation is described to demonstrate an approach to the real-time determination of blend homogeneity.

Radiation Belt Storm Probes: Resolving Fundamental Physics with Practical Consequences

NASA Technical Reports Server (NTRS)

Ukhorskiy, Aleksandr Y.; Mauk, Barry H.; Fox, Nicola J.; Sibeck, David G.; Grebowsky, Joseph M.

2011-01-01

The fundamental processes that energize, transport, and cause the loss of charged particles operate throughout the universe at locations as diverse as magnetized planets, the solar wind, our Sun, and other stars. The same processes operate within our immediate environment, the Earth's radiation belts. The Radiation Belt Storm Probes (RBSP) mission will provide coordinated two-spacecraft observations to obtain understanding of these fundamental processes controlling the dynamic variability of the near-Earth radiation environment. In this paper we discuss some of the profound mysteries of the radiation belt physics that will be addressed by RBSP and briefly describe the mission and its goals.

Neural Control of Posture in Individuals with Persisting Postconcussion Symptoms.

PubMed

Helmich, Ingo; Berger, Alisa; Lausberg, Hedda

2016-12-01

Postural instability has been shown to characterize individuals who suffered from long-term symptoms after mild traumatic brain injury. However, recordings of neural processes during postural control are difficult to realize with standard neuroimaging techniques. Thus, we used functional nearinfrared spectroscopy to investigate brain oxygenation of individuals with persistent postconcussion symptoms (pPCS) during postural control in altered environments. We compared brain oxygenation and postural sway during balance control in three groups: individuals suffering from pPCS, individuals with a history of mild traumatic brain injury but without pPCS, and healthy controls. Individuals were investigated during postural control tasks with six different conditions: i) eyes opened, ii) eyes closed, and iii) blurred visual input, each while standing a) on a stable and b) an unstable surface. In all groups, during the eyes closed/unstable surface condition as compared with the other conditions, the postural sway increased as well as the brain oxygenation in frontal brain cortices. In the most difficult balance condition, as compared with the other two groups, subjects with pPCS applied more force over time to keep balance as measured by the force plate system with a significantly greater activation in frontopolar/orbitofrontal areas of the right hemisphere. As subjects with pPCS applied more force over time to control balance, we propose that with regard to cognitive processes, the increase of cerebral activation in these individuals indicates an increase of attention-demanding processes during postural control in altered environments.

Listeria monocytogenes in Food-Processing Facilities, Food Contamination, and Human Listeriosis: The Brazilian Scenario.

PubMed

Camargo, Anderson Carlos; Woodward, Joshua John; Call, Douglas Ruben; Nero, Luís Augusto

2017-11-01

Listeria monocytogenes is a foodborne pathogen that contaminates food-processing environments and persists within biofilms on equipment, utensils, floors, and drains, ultimately reaching final products by cross-contamination. This pathogen grows even under high salt conditions or refrigeration temperatures, remaining viable in various food products until the end of their shelf life. While the estimated incidence of listeriosis is lower than other enteric illnesses, infections caused by L. monocytogenes are more likely to lead to hospitalizations and fatalities. Despite the description of L. monocytogenes occurrence in Brazilian food-processing facilities and foods, there is a lack of consistent data regarding listeriosis cases and outbreaks directly associated with food consumption. Listeriosis requires rapid treatment with antibiotics and most drugs suitable for Gram-positive bacteria are effective against L. monocytogenes. Only a minority of clinical antibiotic-resistant L. monocytogenes strains have been described so far; whereas many strains recovered from food-processing facilities and foods exhibited resistance to antimicrobials not suitable against listeriosis. L. monocytogenes control in food industries is a challenge, demanding proper cleaning and application of sanitization procedures to eliminate this foodborne pathogen from the food-processing environment and ensure food safety. This review focuses on presenting the L. monocytogenes distribution in food-processing environment, food contamination, and control in the food industry, as well as the consequences of listeriosis to human health, providing a comparison of the current Brazilian situation with the international scenario.

The lifecycle of e-learning course in the adaptive educational environment

NASA Astrophysics Data System (ADS)

Gustun, O. N.; Budaragin, N. V.

2017-01-01

In the article we have considered the lifecycle model of the e-learning course in the electronic educational environment. This model consists of three stages and nine phases. In order to implement the adaptive control of the learning process we have determined the actions which are necessary to undertake at different phases of the e-learning course lifecycle. The general characteristics of the SPACEL-technology is given for creating adaptive educational environments of the next generation.

Growth Control and Disease Mechanisms in Computational Embryogeny

NASA Technical Reports Server (NTRS)

Shapiro, Andrew A.; Yogev, Or; Antonsson, Erik K.

2008-01-01

This paper presents novel approach to applying growth control and diseases mechanisms in computational embryogeny. Our method, which mimics fundamental processes from biology, enables individuals to reach maturity in a controlled process through a stochastic environment. Three different mechanisms were implemented; disease mechanisms, gene suppression, and thermodynamic balancing. This approach was integrated as part of a structural evolutionary model. The model evolved continuum 3-D structures which support an external load. By using these mechanisms we were able to evolve individuals that reached a fixed size limit through the growth process. The growth process was an integral part of the complete development process. The size of the individuals was determined purely by the evolutionary process where different individuals matured to different sizes. Individuals which evolved with these characteristics have been found to be very robust for supporting a wide range of external loads.

EEGLAB, SIFT, NFT, BCILAB, and ERICA: new tools for advanced EEG processing.

PubMed

Delorme, Arnaud; Mullen, Tim; Kothe, Christian; Akalin Acar, Zeynep; Bigdely-Shamlo, Nima; Vankov, Andrey; Makeig, Scott

2011-01-01

We describe a set of complementary EEG data collection and processing tools recently developed at the Swartz Center for Computational Neuroscience (SCCN) that connect to and extend the EEGLAB software environment, a freely available and readily extensible processing environment running under Matlab. The new tools include (1) a new and flexible EEGLAB STUDY design facility for framing and performing statistical analyses on data from multiple subjects; (2) a neuroelectromagnetic forward head modeling toolbox (NFT) for building realistic electrical head models from available data; (3) a source information flow toolbox (SIFT) for modeling ongoing or event-related effective connectivity between cortical areas; (4) a BCILAB toolbox for building online brain-computer interface (BCI) models from available data, and (5) an experimental real-time interactive control and analysis (ERICA) environment for real-time production and coordination of interactive, multimodal experiments.

A development framework for distributed artificial intelligence

NASA Technical Reports Server (NTRS)

Adler, Richard M.; Cottman, Bruce H.

1989-01-01

The authors describe distributed artificial intelligence (DAI) applications in which multiple organizations of agents solve multiple domain problems. They then describe work in progress on a DAI system development environment, called SOCIAL, which consists of three primary language-based components. The Knowledge Object Language defines models of knowledge representation and reasoning. The metaCourier language supplies the underlying functionality for interprocess communication and control access across heterogeneous computing environments. The metaAgents language defines models for agent organization coordination, control, and resource management. Application agents and agent organizations will be constructed by combining metaAgents and metaCourier building blocks with task-specific functionality such as diagnostic or planning reasoning. This architecture hides implementation details of communications, control, and integration in distributed processing environments, enabling application developers to concentrate on the design and functionality of the intelligent agents and agent networks themselves.

Characteristics of nurses and hospital work environments that foster satisfaction and clinical expertise.

PubMed

Foley, Barbara Jo; Kee, Carolyn C; Minick, Ptlene; Harvey, Susan S; Jennings, Bonnie M

2002-05-01

The purpose of this aspect of a larger study was to describe characteristics of nurses and their work environment at two military hospitals. Few studies have explored characteristics among nurses who practice in military hospitals. There is reason to believe that differences exist between nurses who work in military and civilian hospitals, some of which are required educational level, leadership experience, officer status, and career development opportunities. A descriptive design was used to address how military and civilian nurses who work in military hospitals describe their autonomy, control over practice, nurse-physician collaboration, and clinical expertise and what relationships exist among these variables. Scores on autonomy, control over practice, and nurse-physician relationships all were above midpoint for all respondents as a group, indicating positive work environments in both of the military hospitals studied. Scores from the clinical expertise instrument were well above midpoint, indicating a desirable level of clinical expertise. These findings all reflect favorably on the military hospital work environment. This information will help to make a case for instituting or preserving those nursing processes that are effective and for identifying and working to change nursing processes that are not effective. Nurses will benefit by having a more collaborative work environment.

SoftLab: A Soft-Computing Software for Experimental Research with Commercialization Aspects

NASA Technical Reports Server (NTRS)

Akbarzadeh-T, M.-R.; Shaikh, T. S.; Ren, J.; Hubbell, Rob; Kumbla, K. K.; Jamshidi, M

1998-01-01

SoftLab is a software environment for research and development in intelligent modeling/control using soft-computing paradigms such as fuzzy logic, neural networks, genetic algorithms, and genetic programs. SoftLab addresses the inadequacies of the existing soft-computing software by supporting comprehensive multidisciplinary functionalities from management tools to engineering systems. Furthermore, the built-in features help the user process/analyze information more efficiently by a friendly yet powerful interface, and will allow the user to specify user-specific processing modules, hence adding to the standard configuration of the software environment.

Controlled Directional Solidification of Aluminum - 7 wt Percent Silicon Alloys: Comparison Between Samples Processed on Earth and in the Microgravity Environment Aboard the International Space Station

NASA Technical Reports Server (NTRS)

Grugel, Richard N.; Tewari, Surendra N.; Erdman, Robert G.; Poirier, David R.

2012-01-01

An overview of the international "MIcrostructure Formation in CASTing of Technical Alloys" (MICAST) program is given. Directional solidification processing of metals and alloys is described, and why experiments conducted in the microgravity environment aboard the International Space Station (ISS) are expected to promote our understanding of this commercially relevant practice. Microstructural differences observed when comparing the aluminum - 7 wt% silicon alloys directionally solidified on Earth to those aboard the ISS are presented and discussed.

Framework Programmable Platform for the advanced software development workstation: Framework processor design document

NASA Technical Reports Server (NTRS)

Mayer, Richard J.; Blinn, Thomas M.; Mayer, Paula S. D.; Ackley, Keith A.; Crump, Wes; Sanders, Les

1991-01-01

The design of the Framework Processor (FP) component of the Framework Programmable Software Development Platform (FFP) is described. The FFP is a project aimed at combining effective tool and data integration mechanisms with a model of the software development process in an intelligent integrated software development environment. Guided by the model, this Framework Processor will take advantage of an integrated operating environment to provide automated support for the management and control of the software development process so that costly mistakes during the development phase can be eliminated.

Dynamic control and information processing in chemical reaction systems by tuning self-organization behavior

NASA Astrophysics Data System (ADS)

Lebiedz, Dirk; Brandt-Pollmann, Ulrich

2004-09-01

Specific external control of chemical reaction systems and both dynamic control and signal processing as central functions in biochemical reaction systems are important issues of modern nonlinear science. For example nonlinear input-output behavior and its regulation are crucial for the maintainance of the life process that requires extensive communication between cells and their environment. An important question is how the dynamical behavior of biochemical systems is controlled and how they process information transmitted by incoming signals. But also from a general point of view external forcing of complex chemical reaction processes is important in many application areas ranging from chemical engineering to biomedicine. In order to study such control issues numerically, here, we choose a well characterized chemical system, the CO oxidation on Pt(110), which is interesting per se as an externally forced chemical oscillator model. We show numerically that tuning of temporal self-organization by input signals in this simple nonlinear chemical reaction exhibiting oscillatory behavior can in principle be exploited for both specific external control of dynamical system behavior and processing of complex information.

Contamination control methods for gases used in the microlithography process

NASA Astrophysics Data System (ADS)

Rabellino, Larry; Applegarth, Chuck; Vergani, Giorgio

2002-07-01

Sensitivity to contamination continues to increase as the technology shrinks from 365 nm I-line lamp illumination to 13.4 nm Extreme Ultraviolet laser activated plasma. Gas borne impurities can be readily distributed within the system, remaining both suspended in the gas and attached to critical surfaces. Effects from a variety of contamination, some well characterized and others not, remain a continuing obstacle for stepper manufacturers and users. Impurities like oxygen, moisture and hydrocarbons in parts per billion levels can absorb light, reducing the light intensity and subsequently reducing the consistence of the process. Moisture, sulfur compounds, ammonia, acid compounds and organic compounds such as hydrocarbons can deposit on lens or mirror surfaces affecting image quality. Regular lens replacement or removal for cleaning is a costly option and in-situ cleaning processes must be carefully managed to avoid recontamination of the system. The contamination can come from outside the controlled environment (local gas supply, piping system, & leaks), or from the materials moving into the controlled environment; or contamination may be generated inside the controlled environment as a result of the process itself. The release of amines can occur as a result of the degassing of the photo-resists. For the manufacturer and user of stepper equipment, the challenge is not in predictable contamination, but the variable or unpredictable contamination in the process. One type of unpredictable contamination may be variation in the environmental conditions when producing the nitrogen gas and Clean Dry Air (CDA). Variation in the CDA, nitrogen and xenon may range from parts per billion to parts per million. The risk due to uncontrolled or unmonitored variation in gas quality can be directly related to product defects. Global location can significantly affect the gas quality, due to the ambient air quality (for nitrogen and CDA), production methods, gas handling equipment maintenance, transportation and storage processes. Fortunately, technology has been developed which can remove the killer impurities from these processes. This paper will review processes, and purification media that can be used in the photolithography processes, and detail the advances in purification technologies for removal of hydrocarbons, oxygen (where applicable), moisture, carbon dioxide, carbon monoxide, hydrogen, nitrogen (where applicable), sulfur compounds, ammonia and acid compounds from process gases such as nitrogen, CDA, argon, krypton and xenon.

Use of adaptive cruise control functions on motorways and urban roads: Changes over time in an on-road study.

PubMed

Pereira, Marta; Beggiato, Matthias; Petzoldt, Tibor

2015-09-01

The study aimed at investigating how drivers use Adaptive Cruise Control and its functions in distinct road environments and to verify if changes occur over time. Fifteen participants were invited to drive a vehicle equipped with a Stop & Go Adaptive Cruise Control system on nine occasions. The course remained the same for each test run and included roads on urban and motorway environments. Results showed significant effect of experience for ACC usage percentage, and selection of the shortest time headway value in the urban road environment. This indicates that getting to know a system is not a homogenous process, as mastering the use of all the system's functions can take differing lengths of time in distinct road environments. Results can be used not only for the development of the new generation of systems that integrate ACC functionalities but also for determining the length of training required to operate an ACC system. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

HORMONAL PROCESSES IN DECAPOD CRUSTACEAN LARVAE AS BIOMARKERS OF ENDOCRINE DISRUPTING CHEMICALS IN THE MARINE ENVIRONMENT

EPA Science Inventory

Knowledge of endocrine control of the complex larval developmental processes in insects (metamorphosis) has led to the introduction of insect hormones and their analogues as insecticides known as insect growth regulators (IGRs) with the largest group being juvenile hormone analog...

40 CFR 424.52 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... practicable control technology currently available (BPT): There shall be no discharge of process waste water... technology currently available. 424.52 Section 424.52 Protection of Environment ENVIRONMENTAL PROTECTION... effluent reduction attainable by the application of the best practicable control technology currently...

40 CFR 436.182 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... technology currently available. 436.182 Section 436.182 Protection of Environment ENVIRONMENTAL PROTECTION... reduction attainable by the application of the best practicable control technology currently available. (a... practicable control technology currently available (BPT): (1) Discharges of process generated waste water and...

40 CFR 436.22 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... technology currently available. 436.22 Section 436.22 Protection of Environment ENVIRONMENTAL PROTECTION... degree of effluent reduction attainable by the application of the best practicable control technology... of the best practicable control technology currently available (BPT): (1) Discharges of process...

40 CFR 436.182 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... technology currently available. 436.182 Section 436.182 Protection of Environment ENVIRONMENTAL PROTECTION... reduction attainable by the application of the best practicable control technology currently available. (a... practicable control technology currently available (BPT): (1) Discharges of process generated waste water and...

40 CFR 436.22 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... technology currently available. 436.22 Section 436.22 Protection of Environment ENVIRONMENTAL PROTECTION... degree of effluent reduction attainable by the application of the best practicable control technology... of the best practicable control technology currently available (BPT): (1) Discharges of process...

40 CFR 436.22 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... technology currently available. 436.22 Section 436.22 Protection of Environment ENVIRONMENTAL PROTECTION... degree of effluent reduction attainable by the application of the best practicable control technology... of the best practicable control technology currently available (BPT): (1) Discharges of process...

40 CFR 408.297 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... control technology. 408.297 Section 408.297 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... of effluent reduction attainable by the application of the best conventional pollutant control... facility located in population or processing centers including but not limited to Anchorage, Cordova...

40 CFR 408.297 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... control technology. 408.297 Section 408.297 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... of effluent reduction attainable by the application of the best conventional pollutant control... facility located in population or processing centers including but not limited to Anchorage, Cordova...

40 CFR 408.297 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... control technology. 408.297 Section 408.297 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... of effluent reduction attainable by the application of the best conventional pollutant control... facility located in population or processing centers including but not limited to Anchorage, Cordova...

40 CFR 408.297 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... control technology. 408.297 Section 408.297 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... of effluent reduction attainable by the application of the best conventional pollutant control... facility located in population or processing centers including but not limited to Anchorage, Cordova...

40 CFR 408.297 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... control technology. 408.297 Section 408.297 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... of effluent reduction attainable by the application of the best conventional pollutant control... facility located in population or processing centers including but not limited to Anchorage, Cordova...

40 CFR 63.144 - Process wastewater provisions-test methods and procedures for determining applicability and Group...

Code of Federal Regulations, 2013 CFR

2013-07-01

... and Group 1/Group 2 determinations (determining which wastewater streams require control). (a... methods and procedures for determining applicability and Group 1/Group 2 determinations (determining which wastewater streams require control). 63.144 Section 63.144 Protection of Environment ENVIRONMENTAL PROTECTION...

40 CFR 63.144 - Process wastewater provisions-test methods and procedures for determining applicability and Group...

Code of Federal Regulations, 2010 CFR

2010-07-01

... and Group 1/Group 2 determinations (determining which wastewater streams require control). (a... methods and procedures for determining applicability and Group 1/Group 2 determinations (determining which wastewater streams require control). 63.144 Section 63.144 Protection of Environment ENVIRONMENTAL PROTECTION...

40 CFR 63.144 - Process wastewater provisions-test methods and procedures for determining applicability and Group...

Code of Federal Regulations, 2014 CFR

2014-07-01

... and Group 1/Group 2 determinations (determining which wastewater streams require control). (a... methods and procedures for determining applicability and Group 1/Group 2 determinations (determining which wastewater streams require control). 63.144 Section 63.144 Protection of Environment ENVIRONMENTAL PROTECTION...

40 CFR 63.144 - Process wastewater provisions-test methods and procedures for determining applicability and Group...

Code of Federal Regulations, 2011 CFR

2011-07-01

... and Group 1/Group 2 determinations (determining which wastewater streams require control). (a... methods and procedures for determining applicability and Group 1/Group 2 determinations (determining which wastewater streams require control). 63.144 Section 63.144 Protection of Environment ENVIRONMENTAL PROTECTION...

40 CFR 63.144 - Process wastewater provisions-test methods and procedures for determining applicability and Group...

Code of Federal Regulations, 2012 CFR

2012-07-01

... and Group 1/Group 2 determinations (determining which wastewater streams require control). (a... methods and procedures for determining applicability and Group 1/Group 2 determinations (determining which wastewater streams require control). 63.144 Section 63.144 Protection of Environment ENVIRONMENTAL PROTECTION...

Double Vacuum Bag Process for Resin Matrix Composite Manufacturing

NASA Technical Reports Server (NTRS)

Hou, Tan-Hung (Inventor); Jensen, Brian J. (Inventor)

2007-01-01

A double vacuum bag molding assembly with improved void management and laminate net shape control which provides a double vacuum enviromnent for use in fabricating composites from prepregs containing air and/or volatiles such as reactive resin matrix composites or composites from solvent containing prepregs with non-reactive resins matrices. By using two vacuum environments during the curing process, a vacuum can be drawn during a B-stage of a two-step cycle without placing the composite under significant relative pressure. During the final cure stage, a significant pressure can be applied by releasing the vacuum in one of the two environments. Inner and outer bags are useful for creating the two vacuum environments with a perforated tool intermediate the two. The composite is placed intermediate a tool plate and a caul plate in the first environment with the inner bag and tool plate defining the first environment. The second environment is characterized by the outer bag which is placed over the inner bag and the tool plate.

Modeling, simulation and control for a cryogenic fluid management facility, preliminary report

NASA Technical Reports Server (NTRS)

Turner, Max A.; Vanbuskirk, P. D.

1986-01-01

The synthesis of a control system for a cryogenic fluid management facility was studied. The severe demand for reliability as well as instrumentation and control unique to the Space Station environment are prime considerations. Realizing that the effective control system depends heavily on quantitative description of the facility dynamics, a methodology for process identification and parameter estimation is postulated. A block diagram of the associated control system is also produced. Finally, an on-line adaptive control strategy is developed utilizing optimization of the velocity form control parameters (proportional gains, integration and derivative time constants) in appropriate difference equations for direct digital control. Of special concern are the communications, software and hardware supporting interaction between the ground and orbital systems. It is visualized that specialist in the OSI/ISO utilizing the Ada programming language will influence further development, testing and validation of the simplistic models presented here for adaptation to the actual flight environment.

Active Combustion Control for Aircraft Gas Turbine Engines

NASA Technical Reports Server (NTRS)

DeLaat, John C.; Breisacher, Kevin J.; Saus, Joseph R.; Paxson, Daniel E.

2000-01-01

Lean-burning combustors are susceptible to combustion instabilities. Additionally, due to non-uniformities in the fuel-air mixing and in the combustion process, there typically exist hot areas in the combustor exit plane. These hot areas limit the operating temperature at the turbine inlet and thus constrain performance and efficiency. Finally, it is necessary to optimize the fuel-air ratio and flame temperature throughout the combustor to minimize the production of pollutants. In recent years, there has been considerable activity addressing Active Combustion Control. NASA Glenn Research Center's Active Combustion Control Technology effort aims to demonstrate active control in a realistic environment relevant to aircraft engines. Analysis and experiments are tied to aircraft gas turbine combustors. Considerable progress has been shown in demonstrating technologies for Combustion Instability Control, Pattern Factor Control, and Emissions Minimizing Control. Future plans are to advance the maturity of active combustion control technology to eventual demonstration in an engine environment.

Development of visual 3D virtual environment for control software

NASA Technical Reports Server (NTRS)

Hirose, Michitaka; Myoi, Takeshi; Amari, Haruo; Inamura, Kohei; Stark, Lawrence

1991-01-01

Virtual environments for software visualization may enable complex programs to be created and maintained. A typical application might be for control of regional electric power systems. As these encompass broader computer networks than ever, construction of such systems becomes very difficult. Conventional text-oriented environments are useful in programming individual processors. However, they are obviously insufficient to program a large and complicated system, that includes large numbers of computers connected to each other; such programming is called 'programming in the large.' As a solution for this problem, the authors are developing a graphic programming environment wherein one can visualize complicated software in virtual 3D world. One of the major features of the environment is the 3D representation of concurrent process. 3D representation is used to supply both network-wide interprocess programming capability (capability for 'programming in the large') and real-time programming capability. The authors' idea is to fuse both the block diagram (which is useful to check relationship among large number of processes or processors) and the time chart (which is useful to check precise timing for synchronization) into a single 3D space. The 3D representation gives us a capability for direct and intuitive planning or understanding of complicated relationship among many concurrent processes. To realize the 3D representation, a technology to enable easy handling of virtual 3D object is a definite necessity. Using a stereo display system and a gesture input device (VPL DataGlove), our prototype of the virtual workstation has been implemented. The workstation can supply the 'sensation' of the virtual 3D space to a programmer. Software for the 3D programming environment is implemented on the workstation. According to preliminary assessments, a 50 percent reduction of programming effort is achieved by using the virtual 3D environment. The authors expect that the 3D environment has considerable potential in the field of software engineering.

Oxygen-controlled automated neural differentiation of mouse embryonic stem cells.

PubMed

Mondragon-Teran, Paul; Tostoes, Rui; Mason, Chris; Lye, Gary J; Veraitch, Farlan S

2013-03-01

Automation and oxygen tension control are two tools that provide significant improvements to the reproducibility and efficiency of stem cell production processes. the aim of this study was to establish a novel automation platform capable of controlling oxygen tension during both the cell-culture and liquid-handling steps of neural differentiation processes. We built a bespoke automation platform, which enclosed a liquid-handling platform in a sterile, oxygen-controlled environment. An airtight connection was used to transfer cell culture plates to and from an automated oxygen-controlled incubator. Our results demonstrate that our system yielded comparable cell numbers, viabilities, metabolism profiles and differentiation efficiencies when compared with traditional manual processes. Interestingly, eliminating exposure to ambient conditions during the liquid-handling stage resulted in significant improvements in the yield of MAP2-positive neural cells, indicating that this level of control can improve differentiation processes. This article describes, for the first time, an automation platform capable of maintaining oxygen tension control during both the cell-culture and liquid-handling stages of a 2D embryonic stem cell differentiation process.

40 CFR 63.497 - Back-end process provisions-monitoring provisions for control and recovery devices used to comply...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 9 2011-07-01 2011-07-01 false Back-end process provisions-monitoring... Standards for Hazardous Air Pollutant Emissions: Group I Polymers and Resins § 63.497 Back-end process... limitations. (a) An owner or operator complying with the residual organic HAP limitations in § 63.494(a)(1...

Network-based production quality control

NASA Astrophysics Data System (ADS)

Kwon, Yongjin; Tseng, Bill; Chiou, Richard

2007-09-01

This study investigates the feasibility of remote quality control using a host of advanced automation equipment with Internet accessibility. Recent emphasis on product quality and reduction of waste stems from the dynamic, globalized and customer-driven market, which brings opportunities and threats to companies, depending on the response speed and production strategies. The current trends in industry also include a wide spread of distributed manufacturing systems, where design, production, and management facilities are geographically dispersed. This situation mandates not only the accessibility to remotely located production equipment for monitoring and control, but efficient means of responding to changing environment to counter process variations and diverse customer demands. To compete under such an environment, companies are striving to achieve 100%, sensor-based, automated inspection for zero-defect manufacturing. In this study, the Internet-based quality control scheme is referred to as "E-Quality for Manufacturing" or "EQM" for short. By its definition, EQM refers to a holistic approach to design and to embed efficient quality control functions in the context of network integrated manufacturing systems. Such system let designers located far away from the production facility to monitor, control and adjust the quality inspection processes as production design evolves.

The TAME Project: Towards improvement-oriented software environments

NASA Technical Reports Server (NTRS)

Basili, Victor R.; Rombach, H. Dieter

1988-01-01

Experience from a dozen years of analyzing software engineering processes and products is summarized as a set of software engineering and measurement principles that argue for software engineering process models that integrate sound planning and analysis into the construction process. In the TAME (Tailoring A Measurement Environment) project at the University of Maryland, such an improvement-oriented software engineering process model was developed that uses the goal/question/metric paradigm to integrate the constructive and analytic aspects of software development. The model provides a mechanism for formalizing the characterization and planning tasks, controlling and improving projects based on quantitative analysis, learning in a deeper and more systematic way about the software process and product, and feeding the appropriate experience back into the current and future projects. The TAME system is an instantiation of the TAME software engineering process model as an ISEE (integrated software engineering environment). The first in a series of TAME system prototypes has been developed. An assessment of experience with this first limited prototype is presented including a reassessment of its initial architecture.

Image processing occupancy sensor

DOEpatents

Brackney, Larry J.

2016-09-27

A system and method of detecting occupants in a building automation system environment using image based occupancy detection and position determinations. In one example, the system includes an image processing occupancy sensor that detects the number and position of occupants within a space that has controllable building elements such as lighting and ventilation diffusers. Based on the position and location of the occupants, the system can finely control the elements to optimize conditions for the occupants, optimize energy usage, among other advantages.

Decoherence control mechanisms of a charged magneto-oscillator in contact with different environments

NASA Astrophysics Data System (ADS)

Rajesh, Asam; Bandyopadhyay, Malay; Jayannavar, Arun M.

2017-12-01

In this work, we consider two different techniques based on reservoir engineering process and quantum Zeno control method to analyze the decoherence control mechanism of a charged magneto-oscillator in contact with different type of environment. Our analysis reveals that both the control mechanisms are very much sensitive on the details of different environmental spectrum (J (ω)), and also on different system and reservoir parameters, e.g., external magnetic field (rc), confinement length (r0), temperature (T), cut-off frequency of reservoir spectrum (ωcut), and measurement interval (τ). We also demonstrate the manipulation scheme of the continuous passage from decay suppression to decay acceleration by tuning the above mentioned system or reservoir parameters, e.g., rc, r0, T and τ.

Automation software for a materials testing laboratory

NASA Technical Reports Server (NTRS)

Mcgaw, Michael A.; Bonacuse, Peter J.

1990-01-01

The software environment in use at the NASA-Lewis Research Center's High Temperature Fatigue and Structures Laboratory is reviewed. This software environment is aimed at supporting the tasks involved in performing materials behavior research. The features and capabilities of the approach to specifying a materials test include static and dynamic control mode switching, enabling multimode test control; dynamic alteration of the control waveform based upon events occurring in the response variables; precise control over the nature of both command waveform generation and data acquisition; and the nesting of waveform/data acquisition strategies so that material history dependencies may be explored. To eliminate repetitive tasks in the coventional research process, a communications network software system is established which provides file interchange and remote console capabilities.

Evaluation of glucose controllers in virtual environment: methodology and sample application.

PubMed

Chassin, Ludovic J; Wilinska, Malgorzata E; Hovorka, Roman

2004-11-01

Adaptive systems to deliver medical treatment in humans are safety-critical systems and require particular care in both the testing and the evaluation phase, which are time-consuming, costly, and confounded by ethical issues. The objective of the present work is to develop a methodology to test glucose controllers of an artificial pancreas in a simulated (virtual) environment. A virtual environment comprising a model of the carbohydrate metabolism and models of the insulin pump and the glucose sensor is employed to simulate individual glucose excursions in subjects with type 1 diabetes. The performance of the control algorithm within the virtual environment is evaluated by considering treatment and operational scenarios. The developed methodology includes two dimensions: testing in relation to specific life style conditions, i.e. fasting, post-prandial, and life style (metabolic) disturbances; and testing in relation to various operating conditions, i.e. expected operating conditions, adverse operating conditions, and system failure. We define safety and efficacy criteria and describe the measures to be taken prior to clinical testing. The use of the methodology is exemplified by tuning and evaluating a model predictive glucose controller being developed for a wearable artificial pancreas focused on fasting conditions. Our methodology to test glucose controllers in a virtual environment is instrumental in anticipating the results of real clinical tests for different physiological conditions and for different operating conditions. The thorough testing in the virtual environment reduces costs and speeds up the development process.

Spacecraft attitude control using a smart control system

NASA Technical Reports Server (NTRS)

Buckley, Brian; Wheatcraft, Louis

1992-01-01

Traditionally, spacecraft attitude control has been implemented using control loops written in native code for a space hardened processor. The Naval Research Lab has taken this approach during the development of the Attitude Control Electronics (ACE) package. After the system was developed and delivered, NRL decided to explore alternate technologies to accomplish this same task more efficiently. The approach taken by NRL was to implement the ACE control loops using systems technologies. The purpose of this effort was to: (1) research capabilities required of an expert system in processing a classic closed-loop control algorithm; (2) research the development environment required to design and test an embedded expert systems environment; (3) research the complexity of design and development of expert systems versus a conventional approach; and (4) test the resulting systems against the flight acceptance test software for both response and accuracy. Two expert systems were selected to implement the control loops. Criteria used for the selection of the expert systems included that they had to run in both embedded systems and ground based environments. Using two different expert systems allowed a comparison of the real-time capabilities, inferencing capabilities, and the ground-based development environment. The two expert systems chosen for the evaluation were Spacecraft Command Language (SCL), and NEXTPERT Object. SCL is a smart control system produced for the NRL by Interface and Control Systems (ICS). SCL was developed to be used for real-time command, control, and monitoring of a new generation of spacecraft. NEXPERT Object is a commercially available product developed by Neuron Data. Results of the effort were evaluated using the ACE test bed. The ACE test bed had been developed and used to test the original flight hardware and software using simulators and flight-like interfaces. The test bed was used for testing the expert systems in a 'near-flight' environment. The technical approach, the system architecture, the development environments, knowledge base development, and results of this effort are detailed.

Artificial intelligence in a mission operations and satellite test environment

NASA Technical Reports Server (NTRS)

Busse, Carl

1988-01-01

A Generic Mission Operations System using Expert System technology to demonstrate the potential of Artificial Intelligence (AI) automated monitor and control functions in a Mission Operations and Satellite Test environment will be developed at the National Aeronautics and Space Administration (NASA) Jet Propulsion Laboratory (JPL). Expert system techniques in a real time operation environment are being studied and applied to science and engineering data processing. Advanced decommutation schemes and intelligent display technology will be examined to develop imaginative improvements in rapid interpretation and distribution of information. The Generic Payload Operations Control Center (GPOCC) will demonstrate improved data handling accuracy, flexibility, and responsiveness in a complex mission environment. The ultimate goal is to automate repetitious mission operations, instrument, and satellite test functions by the applications of expert system technology and artificial intelligence resources and to enhance the level of man-machine sophistication.

Propositions Toward the Survival of a Self-Endangered Species: The Fundamental Question.

ERIC Educational Resources Information Center

Brandwein, Paul F.

The author considers the search for a better, pollution-free environment and the political processes by which various groups attempt to influence or control the actions of others in the context. He defines the goal of conservation as a recognition of the interdependence of man and his environment and lists 13 propositions which indicate the urgent…

An Analysis of the Navy Regional Data Automation Center (NARDAC) chargeback System

DTIC Science & Technology

1986-09-01

addition, operational control is concerned with performing predefined activities whereas management control relates to the organiza- tion’s goals and...In effect, the management control system monitors the progress of operations and alerts the "appropriate management level" when performance as measured...architecture, the financial control processes, and the audit function ( Brandon , 1978; Anderson, 1983). In an operating DP environment, however, non-financial

Realization of ActiveX control based on ATL in VC 2008

NASA Astrophysics Data System (ADS)

Li, Shuhua; Tie, Yong

2011-10-01

ActiveX has a key role in web development, this paper realizes the classical program Polygon in the newest Visual C++ environment 2008 and tests each function of control in ActiveX Control Test Container. After that web code is created rapidly via ActiveX Control Pad and it is checked in HTML. Development process and key point attention are summarized systematically which can guide the related developers.

Application of Taguchi Method for Analyzing Factors Affecting the Performance of Coated Carbide Tool When Turning FCD700 in Dry Cutting Condition

NASA Astrophysics Data System (ADS)

Ghani, Jaharah A.; Mohd Rodzi, Mohd Nor Azmi; Zaki Nuawi, Mohd; Othman, Kamal; Rahman, Mohd. Nizam Ab.; Haron, Che Hassan Che; Deros, Baba Md

2011-01-01

Machining is one of the most important manufacturing processes in these modern industries especially for finishing an automotive component after the primary manufacturing processes such as casting and forging. In this study the turning parameters of dry cutting environment (without air, normal air and chilled air), various cutting speed, and feed rate are evaluated using a Taguchi optimization methodology. An orthogonal array L27 (313), signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are employed to analyze the effect of these turning parameters on the performance of a coated carbide tool. The results show that the tool life is affected by the cutting speed, feed rate and cutting environment with contribution of 38%, 32% and 27% respectively. Whereas for the surface roughness, the feed rate is significantly controlled the machined surface produced by 77%, followed by the cutting environment of 19%. The cutting speed is found insignificant in controlling the machined surface produced. The study shows that the dry cutting environment factor should be considered in order to produce longer tool life as well as for obtaining a good machined surface.

Quality by control: Towards model predictive control of mammalian cell culture bioprocesses.

PubMed

Sommeregger, Wolfgang; Sissolak, Bernhard; Kandra, Kulwant; von Stosch, Moritz; Mayer, Martin; Striedner, Gerald

2017-07-01

The industrial production of complex biopharmaceuticals using recombinant mammalian cell lines is still mainly built on a quality by testing approach, which is represented by fixed process conditions and extensive testing of the end-product. In 2004 the FDA launched the process analytical technology initiative, aiming to guide the industry towards advanced process monitoring and better understanding of how critical process parameters affect the critical quality attributes. Implementation of process analytical technology into the bio-production process enables moving from the quality by testing to a more flexible quality by design approach. The application of advanced sensor systems in combination with mathematical modelling techniques offers enhanced process understanding, allows on-line prediction of critical quality attributes and subsequently real-time product quality control. In this review opportunities and unsolved issues on the road to a successful quality by design and dynamic control implementation are discussed. A major focus is directed on the preconditions for the application of model predictive control for mammalian cell culture bioprocesses. Design of experiments providing information about the process dynamics upon parameter change, dynamic process models, on-line process state predictions and powerful software environments seem to be a prerequisite for quality by control realization. © 2017 The Authors. Biotechnology Journal published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Use telecommunications for real-time process control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zilberman, I.; Bigman, J.; Sela, I.

1996-05-01

Process operators design real-time accurate information to monitor and control product streams and to optimize unit operations. The challenge is how to cost-effectively install sophisticated analytical equipment in harsh environments such as process areas and maintain system reliability. Incorporating telecommunications technology with near infrared (NIR) spectroscopy may be the bridge to help operations achieve their online control goals. Coupling communications fiber optics with NIR analyzers enables the probe and sampling system to remain in the field and crucial analytical equipment to be remotely located in a general purpose area without specialized protection provisions. The case histories show how two refineriesmore » used NIR spectroscopy online to track octane levels for reformate streams.« less

Interface design in the process industries

NASA Technical Reports Server (NTRS)

Beaverstock, M. C.; Stassen, H. G.; Williamson, R. A.

1977-01-01

Every operator runs his plant in accord with his own mental model of the process. In this sense, one characteristic of an ideal man-machine interface is that it be in harmony with that model. With this theme in mind, the paper first reviews the functions of the process operator and compares them with human operators involved in control situations previously studied outside the industrial environment (pilots, air traffic controllers, helmsmen, etc.). A brief history of the operator interface in the process industry and the traditional methodology employed in its design is then presented. Finally, a much more fundamental approach utilizing a model definition of the human operator's behavior is presented.

Tcl as a Software Environment for a TCS

NASA Astrophysics Data System (ADS)

Terrett, David L.

2002-12-01

This paper describes how the Tcl scripting language and C API has been used as the software environment for a telescope pointing kernel so that new pointing algorithms and software architectures can be developed and tested without needing a real-time operating system or real-time software environment. It has enabled development to continue outside the framework of a specific telescope project while continuing to build a system that is sufficiently complete to be capable of controlling real hardware but expending minimum effort on replacing the services that would normally by provided by a real-time software environment. Tcl is used as a scripting language for configuring the system at startup and then as the command interface for controlling the running system; the Tcl C language API is used to provided a system independent interface to file and socket I/O and other operating system services. The pointing algorithms themselves are implemented as a set of C++ objects calling C library functions that implement the algorithms described in [2]. Although originally designed as a test and development environment, the system, running as a soft real-time process on Linux, has been used to test the SOAR mount control system and will be used as the pointing kernel of the SOAR telescope control system

A framework supporting the development of a Grid portal for analysis based on ROI.

PubMed

Ichikawa, K; Date, S; Kaishima, T; Shimojo, S

2005-01-01

In our research on brain function analysis, users require two different simultaneous types of processing: interactive processing to a specific part of data and high-performance batch processing to an entire dataset. The difference between these two types of processing is in whether or not the analysis is for data in the region of interest (ROI). In this study, we propose a Grid portal that has a mechanism to freely assign computing resources to the users on a Grid environment according to the users' two different types of processing requirements. We constructed a Grid portal which integrates interactive processing and batch processing by the following two mechanisms. First, a job steering mechanism controls job execution based on user-tagged priority among organizations with heterogeneous computing resources. Interactive jobs are processed in preference to batch jobs by this mechanism. Second, a priority-based result delivery mechanism that administrates a rank of data significance. The portal ensures a turn-around time of interactive processing by the priority-based job controlling mechanism, and provides the users with quality of services (QoS) for interactive processing. The users can access the analysis results of interactive jobs in preference to the analysis results of batch jobs. The Grid portal has also achieved high-performance computation of MEG analysis with batch processing on the Grid environment. The priority-based job controlling mechanism has been realized to freely assign computing resources to the users' requirements. Furthermore the achievement of high-performance computation contributes greatly to the overall progress of brain science. The portal has thus made it possible for the users to flexibly include the large computational power in what they want to analyze.

EEGLAB, SIFT, NFT, BCILAB, and ERICA: New Tools for Advanced EEG Processing

PubMed Central

Delorme, Arnaud; Mullen, Tim; Kothe, Christian; Akalin Acar, Zeynep; Bigdely-Shamlo, Nima; Vankov, Andrey; Makeig, Scott

2011-01-01

We describe a set of complementary EEG data collection and processing tools recently developed at the Swartz Center for Computational Neuroscience (SCCN) that connect to and extend the EEGLAB software environment, a freely available and readily extensible processing environment running under Matlab. The new tools include (1) a new and flexible EEGLAB STUDY design facility for framing and performing statistical analyses on data from multiple subjects; (2) a neuroelectromagnetic forward head modeling toolbox (NFT) for building realistic electrical head models from available data; (3) a source information flow toolbox (SIFT) for modeling ongoing or event-related effective connectivity between cortical areas; (4) a BCILAB toolbox for building online brain-computer interface (BCI) models from available data, and (5) an experimental real-time interactive control and analysis (ERICA) environment for real-time production and coordination of interactive, multimodal experiments. PMID:21687590

A μ analysis-based, controller-synthesis framework for robust bioinspired visual navigation in less-structured environments.

PubMed

Keshavan, J; Gremillion, G; Escobar-Alvarez, H; Humbert, J S

2014-06-01

Safe, autonomous navigation by aerial microsystems in less-structured environments is a difficult challenge to overcome with current technology. This paper presents a novel visual-navigation approach that combines bioinspired wide-field processing of optic flow information with control-theoretic tools for synthesis of closed loop systems, resulting in robustness and performance guarantees. Structured singular value analysis is used to synthesize a dynamic controller that provides good tracking performance in uncertain environments without resorting to explicit pose estimation or extraction of a detailed environmental depth map. Experimental results with a quadrotor demonstrate the vehicle's robust obstacle-avoidance behaviour in a straight line corridor, an S-shaped corridor and a corridor with obstacles distributed in the vehicle's path. The computational efficiency and simplicity of the current approach offers a promising alternative to satisfying the payload, power and bandwidth constraints imposed by aerial microsystems.

The cybernetics of viability: an overview

NASA Astrophysics Data System (ADS)

Nechansky, Helmut

2011-10-01

A three-level approach to viability is developed, considering (1) living systems, (2) a niche, understood as the area within the reach of their actions, and (3) an environment. A systematic analysis of the interrelations between these levels shows that living systems emerge with matter/energy processing systems. These can add controller structures when producing excess energy. A three-sensor controller structure enables a living system to deal with unfavourable and scarce environments. Further evolution of these controller structures offers improved ways to act on niches. Maintaining niches in scarce environments can require technology or economy. So social systems emerge, which are understood as aggregates of living systems. Basic patterns of interactions within social systems are analysed. So the introduction of the notion of the niche into the discussion of viability allows us to explain phenomena ranging from properties of single living systems to societal organization.

Software-as-a-Service Vendors: Are They Ready to Successfully Deliver?

NASA Astrophysics Data System (ADS)

Heart, Tsipi; Tsur, Noa Shamir; Pliskin, Nava

Software as a service (SaaS) is a software sourcing option that allows organizations to remotely access enterprise applications, without having to install the application in-house. In this work we study vendors' readiness to deliver SaaS, a topic scarcely studied before. The innovation classification (evolutionary vs. revolutionary) and a new, Seven Fundamental Organizational Capabilities (FOCs) Model, are used as the theoretical frameworks. The Seven FOCs model suggests generic yet comprehensive set of capabilities that are required for organizational success: 1) sensing the stakeholders, 2) sensing the business environment, 3) sensing the knowledge environment, 4) process control, 5) process improvement, 6) new process development, and 7) appropriate resolution.

Humidity control of an incubator using the microcontroller-based active humidifier system employing an ultrasonic nebulizer.

PubMed

Güler, I; Burunkaya, M

2002-01-01

Relative humidity levels of an incubator were measured and controlled. An ultrasonic nebulizer system as an active humidifier was used to humidify the incubator environment. An integrated circuit-type humidity sensor was used to measure the humidity level of the incubator environment. Measurement and control processes were achieved by a PIC microcontroller. The high-performance and high-speed PIC provided the flexibility of the system. The developed system can be used effectively for the intensive care of newborns and/or premature babies. Since the humidifier generates an aerosol in ambient conditions, it is possible to provide the high relative humidity level for therapeutic and diagnostic purposes in medicine.

A new intelligent curtain control system based on 51 single chip microcomputer

NASA Astrophysics Data System (ADS)

Sun, Tuan; Wang, Yanhua; Wu, Mengmeng

2017-04-01

This paper uses 51 (single chip microcomputer) SCM as the operation and data processing center. According to the change of sunshine intensity and ambient temperature, a new type of intelligent curtain control system is designed by adopting photosensitive element and temperature sensor. In addition, the design also has a manual control mode. In the rain, when the light intensity is weak, the open position of the curtain can be set by the user. The system can maximize the user to provide user-friendly operation and comfortable living environment. The system can be applied to home or office environment, with a wide range of applications and simple operation and so on.

How Has the Internet Reshaped Human Cognition?

PubMed

Loh, Kep Kee; Kanai, Ryota

2016-10-01

Throughout our evolutionary history, our cognitive systems have been altered by the advent of technological inventions such as primitive tools, spoken language, writing, and arithmetic systems. Thirty years ago, the Internet surfaced as the latest technological invention poised to deeply reshape human cognition. With its multifaceted affordances, the Internet environment has profoundly transformed our thoughts and behaviors. Growing up with Internet technologies, "Digital Natives" gravitate toward "shallow" information processing behaviors characterized by rapid attention shifting and reduced deliberations. They engage in increased multitasking behaviors that are linked to increased distractibility and poor executive control abilities. Digital natives also exhibit higher prevalence of Internet-related addictive behaviors that reflect altered reward-processing and self-control mechanisms. Recent neuroimaging investigations have suggested associations between these Internet-related cognitive impacts and structural changes in the brain. Against mounting apprehension over the Internet's consequences on our cognitive systems, several researchers have lamented that these concerns were often exaggerated beyond existing scientific evidence. In the present review, we aim to provide an objective overview of the Internet's impacts on our cognitive systems. We critically discuss current empirical evidence about how the Internet environment has altered the cognitive behaviors and structures involved in information processing, executive control, and reward-processing. © The Author(s) 2015.

Soil Carbon Dioxide Production and Surface Fluxes: Subsurface Physical Controls

NASA Astrophysics Data System (ADS)

Risk, D.; Kellman, L.; Beltrami, H.

Soil respiration is a critical determinant of landscape carbon balance. Variations in soil temperature and moisture patterns are important physical processes controlling soil respiration which need to be better understood. Relationships between soil respi- ration and physical controls are typically addressed using only surface flux data but other methods also exist which permit more rigorous interpretation of soil respira- tion processes. Here we use a combination of subsurface CO_{2} concentrations, surface CO_{2} fluxes and detailed physical monitoring of the subsurface envi- ronment to examine physical controls on soil CO_{2} production at four climate observatories in Eastern Canada. Results indicate that subsurface CO_{2} produc- tion is more strongly correlated to the subsurface thermal environment than the surface CO_{2} flux. Soil moisture was also found to have an important influence on sub- surface CO_{2} production, particularly in relation to the soil moisture - soil profile diffusivity relationship. Non-diffusive profile CO_{2} transport appears to be im- portant at these sites, resulting in a de-coupling of summertime surface fluxes from subsurface processes and violating assumptions that surface CO_{2} emissions are the result solely of diffusion. These results have implications for the study of soil respiration across a broad range of terrestrial environments.

40 CFR 63.11226 - Affirmative defense for violation of emission standards during malfunction.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., infrequent, and unavoidable failure of air pollution control equipment, process equipment, or a process to..., proper design or better operation and maintenance practices; and (iii) Did not stem from any activity or... minimize the impact of the violation on ambient air quality, the environment, and human health; and (6) All...

77 FR 28401 - Information Collection Activities: Legacy Data Verification Process (LDVP); Submitted for Office...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-14

... and natural gas resources in a manner that is consistent with the need to make such resources... to prevent or minimize the likelihood of blowouts, loss of well control, fires, spillages, physical... the environment or to property, or endanger life or health.'' BSEE's Legacy Data Verification Process...

Modifying the Learning Environment of Students To Enhance Personal Learning.

ERIC Educational Resources Information Center

Dart, Barry C.; Clarke, John A.

The aim of this project is to increase teacher education students' understanding of the learning process by focusing on their own learning experiences. In 1990, 67 preservice teacher education students in 4 classes completed measures of academic locus of control, perceived competencies in self-directed learning, and study processes before and…

Effects of Thinking Style on Design Strategies: Using Bridge Construction Simulation Programs

ERIC Educational Resources Information Center

Sun, Chuen-Tsai; Wang, Dai-Yi; Chang, Yu-Yeh

2013-01-01

Computer simulation users can freely control operational factors and simulation results, repeat processes, make changes, and learn from simulation environment feedback. The focus of this paper is on simulation-based design tools and their effects on student learning processes in a group of 101 Taiwanese senior high school students. Participants…

Mission Assurance Analysis Protocol (MAAP): Assessing Risk in Complex Environments

DTIC Science & Technology

2005-09-01

5 1.7 Focus on Risk .................................................................................. 6 2 Defining Risk ...20 CMU/SEI-2005-TN-032 4.4 Extrinsic and Intrinsic Risk ............................................................. 21 5 Operational Risk in...Section 5 , "Operational Risk in Distributed Processes," we look at the characteristics of operational risk in processes where management control is

9 CFR 430.4 - Control of Listeria monocytogenes in post-lethality exposed ready-to-eat products.

Code of Federal Regulations, 2011 CFR

2011-01-01

... products must control through its HACCP plan or prevent in the processing environment through a Sanitation...: (i) The post-lethality treatment must be included in the establishment's HACCP plan. The... the establishment's HACCP plan or its Sanitation SOP or other prerequisite program. (ii) The...

9 CFR 430.4 - Control of Listeria monocytogenes in post-lethality exposed ready-to-eat products.

Code of Federal Regulations, 2010 CFR

2010-01-01

... products must control through its HACCP plan or prevent in the processing environment through a Sanitation...: (i) The post-lethality treatment must be included in the establishment's HACCP plan. The... the establishment's HACCP plan or its Sanitation SOP or other prerequisite program. (ii) The...

40 CFR 63.1316 - PET and polystyrene affected sources-emissions control provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 12 2012-07-01 2011-07-01 true PET and polystyrene affected sources... and Resins § 63.1316 PET and polystyrene affected sources—emissions control provisions. (a) The owner or operator of an affected source producing PET using a continuous process shall comply with...

40 CFR 63.1316 - PET and polystyrene affected sources-emissions control provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 12 2013-07-01 2013-07-01 false PET and polystyrene affected sources... Polymers and Resins § 63.1316 PET and polystyrene affected sources—emissions control provisions. (a) The owner or operator of an affected source producing PET using a continuous process shall comply with...

40 CFR 63.1316 - PET and polystyrene affected sources-emissions control provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 12 2014-07-01 2014-07-01 false PET and polystyrene affected sources... Polymers and Resins § 63.1316 PET and polystyrene affected sources—emissions control provisions. (a) The owner or operator of an affected source producing PET using a continuous process shall comply with...

System and method for secure group transactions

DOEpatents

Goldsmith, Steven Y [Rochester, MN

2006-04-25

A method and a secure system, processing on one or more computers, provides a way to control a group transaction. The invention uses group consensus access control and multiple distributed secure agents in a network environment. Each secure agent can organize with the other secure agents to form a secure distributed agent collective.

Mass Conflagration: An Analysis and Adaptation of the Shipboard Damage Control Organization

DTIC Science & Technology

1991-03-01

the span of control narrows, as each supervisor is able to better monitor the actions and environment of his subordinates. (6) Communciation and... computed decision is reached by the decision makers, often based on a prior formal doctrine or methodology. [Ref. 4:p. 364] While no decision process

Time dependent genetic analysis links field and controlled environment phenotypes in the model C4 grass Setaria

USDA-ARS?s Scientific Manuscript database

Vertical growth of plants is a dynamic process that is influenced by genetic and environmental factors and has a pronounced effect on overall plant architecture and biomass composition. We have performed twelve controlled growth trials of an interspecific Setaria italica x Setaria viridis recombinan...

A Context-Driven Model for the Flat Roofs Construction Process through Sensing Systems, Internet-of-Things and Last Planner System

PubMed Central

Andújar-Montoya, María Dolores

2017-01-01

The main causes of building defects are errors in the design and the construction phases. These causes related to construction are mainly due to the general lack of control of construction work and represent approximately 75% of the anomalies. In particular, one of the main causes of such anomalies, which end in building defects, is the lack of control over the physical variables of the work environment during the execution of tasks. Therefore, the high percentage of defects detected in buildings that have the root cause in the construction phase could be avoidable with a more accurate and efficient control of the process. The present work proposes a novel integration model based on information and communications technologies for the automation of both construction work and its management at the execution phase, specifically focused on the flat roof construction process. Roofs represent the second area where more defects are claimed. The proposed model is based on a Web system, supported by a service oriented architecture, for the integral management of tasks through the Last Planner System methodology, but incorporating the management of task restrictions from the physical environment variables by designing specific sensing systems. Likewise, all workers are integrated into the management process by Internet-of-Things solutions that guide them throughout the execution process in a non-intrusive and transparent way. PMID:28737693

A Context-Driven Model for the Flat Roofs Construction Process through Sensing Systems, Internet-of-Things and Last Planner System.

PubMed

Andújar-Montoya, María Dolores; Marcos-Jorquera, Diego; García-Botella, Francisco Manuel; Gilart-Iglesias, Virgilio

2017-07-22

The main causes of building defects are errors in the design and the construction phases. These causes related to construction are mainly due to the general lack of control of construction work and represent approximately 75% of the anomalies. In particular, one of the main causes of such anomalies, which end in building defects, is the lack of control over the physical variables of the work environment during the execution of tasks. Therefore, the high percentage of defects detected in buildings that have the root cause in the construction phase could be avoidable with a more accurate and efficient control of the process. The present work proposes a novel integration model based on information and communications technologies for the automation of both construction work and its management at the execution phase, specifically focused on the flat roof construction process. Roofs represent the second area where more defects are claimed. The proposed model is based on a Web system, supported by a service oriented architecture, for the integral management of tasks through the Last Planner System methodology, but incorporating the management of task restrictions from the physical environment variables by designing specific sensing systems. Likewise, all workers are integrated into the management process by Internet-of-Things solutions that guide them throughout the execution process in a non-intrusive and transparent way.

Ada Integrated Environment II Computer Program Development Specification. Part 1.

DTIC Science & Technology

1981-12-01

34Programmable" access 3.2.5.5 controls ; provision for privileged 3.2.5.6 user. 3.3.1 3.3.3 4.1.2.11 3.7.1.2 KDBS - 3.2.5.7 Capability to archive data base...CM -1 1 PHASE I SOW REQUIREMENTS A - SPEC B5 -SPEC 4.111. 3.7.2 1Compiler -331 aMAPSE shall include a mechanism for 1 Linker -3.2.5 aautomatic stub...19 3.2.5.5 Process Administrator The Process Administrator controls the executions of logically concurrent MAPSE processes. The KFW Interface Package

Process to produce silicon carbide fibers using a controlled concentration of boron oxide vapor

NASA Technical Reports Server (NTRS)

Barnard, Thomas Duncan (Inventor); Lipowitz, Jonathan (Inventor); Nguyen, Kimmai Thi (Inventor)

2001-01-01

A process for producing polycrystalline silicon carbide by heating an amorphous ceramic fiber that contains silicon and carbon in an environment containing boron oxide vapor. The boron oxide vapor is produced in situ by the reaction of a boron containing material such as boron carbide and an oxidizing agent such as carbon dioxide, and the amount of boron oxide vapor can be controlled by varying the amount and rate of addition of the oxidizing agent.

Process to produce silicon carbide fibers using a controlled concentration of boron oxide vapor

NASA Technical Reports Server (NTRS)

Barnard, Thomas Duncan (Inventor); Lipowitz, Jonathan (Inventor); Nguyen, Kimmai Thi (Inventor)

2000-01-01

A process for producing polycrystalline silicon carbide includes heating an amorphous ceramic fiber that contains silicon and carbon in an environment containing boron oxide vapor. The boron oxide vapor is produced in situ by the reaction of a boron containing material such as boron carbide and an oxidizing agent such as carbon dioxide, and the amount of boron oxide vapor can be controlled by varying the amount and rate of addition of the oxidizing agent.

The clock is ticking. Ageing of the circadian system: From physiology to cell cycle.

PubMed

Terzibasi-Tozzini, Eva; Martinez-Nicolas, Antonio; Lucas-Sánchez, Alejandro

2017-10-01

The circadian system is the responsible to organise the internal temporal order in relation to the environment of every process of the organisms producing the circadian rhythms. These rhythms have a fixed phase relationship among them and with the environment in order to optimise the available energy and resources. From a cellular level, circadian rhythms are controlled by genetic positive and negative auto-regulated transcriptional and translational feedback loops, which generate 24h rhythms in mRNA and protein levels of the clock components. It has been described about 10% of the genome is controlled by clock genes, with special relevance, due to its implications, to the cell cycle. Ageing is a deleterious process which affects all the organisms' structures including circadian system. The circadian system's ageing may produce a disorganisation among the circadian rhythms, arrhythmicity and, even, disconnection from the environment, resulting in a detrimental situation to the organism. In addition, some environmental conditions can produce circadian disruption, also called chronodisruption, which may produce many pathologies including accelerated ageing. Finally, some strategies to prevent, palliate or counteract chronodisruption effects have been proposed to enhance the circadian system, also called chronoenhancement. This review tries to gather recent advances in the chronobiology of the ageing process, including cell cycle, neurogenesis process and physiology. Copyright © 2017 Elsevier Ltd. All rights reserved.

Combustion Dynamics and Control for Ultra Low Emissions in Aircraft Gas-Turbine Engines

NASA Technical Reports Server (NTRS)

DeLaat, John C.

2011-01-01

Future aircraft engines must provide ultra-low emissions and high efficiency at low cost while maintaining the reliability and operability of present day engines. The demands for increased performance and decreased emissions have resulted in advanced combustor designs that are critically dependent on efficient fuel/air mixing and lean operation. However, all combustors, but most notably lean-burning low-emissions combustors, are susceptible to combustion instabilities. These instabilities are typically caused by the interaction of the fluctuating heat release of the combustion process with naturally occurring acoustic resonances. These interactions can produce large pressure oscillations within the combustor and can reduce component life and potentially lead to premature mechanical failures. Active Combustion Control which consists of feedback-based control of the fuel-air mixing process can provide an approach to achieving acceptable combustor dynamic behavior while minimizing emissions, and thus can provide flexibility during the combustor design process. The NASA Glenn Active Combustion Control Technology activity aims to demonstrate active control in a realistic environment relevant to aircraft engines by providing experiments tied to aircraft gas turbine combustors. The intent is to allow the technology maturity of active combustion control to advance to eventual demonstration in an engine environment. Work at NASA Glenn has shown that active combustion control, utilizing advanced algorithms working through high frequency fuel actuation, can effectively suppress instabilities in a combustor which emulates the instabilities found in an aircraft gas turbine engine. Current efforts are aimed at extending these active control technologies to advanced ultra-low-emissions combustors such as those employing multi-point lean direct injection.

Framework for Development of Object-Oriented Software

NASA Technical Reports Server (NTRS)

Perez-Poveda, Gus; Ciavarella, Tony; Nieten, Dan

2004-01-01

The Real-Time Control (RTC) Application Framework is a high-level software framework written in C++ that supports the rapid design and implementation of object-oriented application programs. This framework provides built-in functionality that solves common software development problems within distributed client-server, multi-threaded, and embedded programming environments. When using the RTC Framework to develop software for a specific domain, designers and implementers can focus entirely on the details of the domain-specific software rather than on creating custom solutions, utilities, and frameworks for the complexities of the programming environment. The RTC Framework was originally developed as part of a Space Shuttle Launch Processing System (LPS) replacement project called Checkout and Launch Control System (CLCS). As a result of the framework s development, CLCS software development time was reduced by 66 percent. The framework is generic enough for developing applications outside of the launch-processing system domain. Other applicable high-level domains include command and control systems and simulation/ training systems.

Online adaptation and over-trial learning in macaque visuomotor control.

PubMed

Braun, Daniel A; Aertsen, Ad; Paz, Rony; Vaadia, Eilon; Rotter, Stefan; Mehring, Carsten

2011-01-01

When faced with unpredictable environments, the human motor system has been shown to develop optimized adaptation strategies that allow for online adaptation during the control process. Such online adaptation is to be contrasted to slower over-trial learning that corresponds to a trial-by-trial update of the movement plan. Here we investigate the interplay of both processes, i.e., online adaptation and over-trial learning, in a visuomotor experiment performed by macaques. We show that simple non-adaptive control schemes fail to perform in this task, but that a previously suggested adaptive optimal feedback control model can explain the observed behavior. We also show that over-trial learning as seen in learning and aftereffect curves can be explained by learning in a radial basis function network. Our results suggest that both the process of over-trial learning and the process of online adaptation are crucial to understand visuomotor learning.

Online Adaptation and Over-Trial Learning in Macaque Visuomotor Control

PubMed Central

Braun, Daniel A.; Aertsen, Ad; Paz, Rony; Vaadia, Eilon; Rotter, Stefan; Mehring, Carsten

2011-01-01

When faced with unpredictable environments, the human motor system has been shown to develop optimized adaptation strategies that allow for online adaptation during the control process. Such online adaptation is to be contrasted to slower over-trial learning that corresponds to a trial-by-trial update of the movement plan. Here we investigate the interplay of both processes, i.e., online adaptation and over-trial learning, in a visuomotor experiment performed by macaques. We show that simple non-adaptive control schemes fail to perform in this task, but that a previously suggested adaptive optimal feedback control model can explain the observed behavior. We also show that over-trial learning as seen in learning and aftereffect curves can be explained by learning in a radial basis function network. Our results suggest that both the process of over-trial learning and the process of online adaptation are crucial to understand visuomotor learning. PMID:21720526

Advanced process control framework initiative

NASA Astrophysics Data System (ADS)

Hill, Tom; Nettles, Steve

1997-01-01

The semiconductor industry, one the world's most fiercely competitive industries, is driven by increasingly complex process technologies and global competition to improve cycle time, quality, and process flexibility. Due to the complexity of these problems, current process control techniques are generally nonautomated, time-consuming, reactive, nonadaptive, and focused on individual fabrication tools and processes. As the semiconductor industry moves into higher density processes, radical new approaches are required. To address the need for advanced factory-level process control in this environment, Honeywell, Advanced Micro Devices (AMD), and SEMATECH formed the Advanced Process Control Framework Initiative (APCFI) joint research project. The project defines and demonstrates an Advanced Process Control (APC) approach based on SEMATECH's Computer Integrated Manufacturing (CIM) Framework. Its scope includes the coordination of Manufacturing Execution Systems, process control tools, and wafer fabrication equipment to provide necessary process control capabilities. Moreover, it takes advantage of the CIM Framework to integrate and coordinate applications from other suppliers that provide services necessary for the overall system to function. This presentation discusses the key concept of model-based process control that differentiates the APC Framework. This major improvement over current methods enables new systematic process control by linking the knowledge of key process settings to desired product characteristics that reside in models created with commercial model development tools The unique framework-based approach facilitates integration of commercial tools and reuse of their data by tying them together in an object-based structure. The presentation also explores the perspective of each organization's involvement in the APCFI project. Each has complementary goals and expertise to contribute; Honeywell represents the supplier viewpoint, AMD represents the user with 'real customer requirements', and SEMATECH provides a consensus-building organization that widely disseminates technology to suppliers and users in the semiconductor industry that face similar equipment and factory control systems challenges.

Friction Stir Process Mapping Methodology

NASA Technical Reports Server (NTRS)

Bjorkman, Gerry; Kooney, Alex; Russell, Carolyn

2003-01-01

The weld process performance for a given weld joint configuration and tool setup is summarized on a 2-D plot of RPM vs. IPM. A process envelope is drawn within the map to identify the range of acceptable welds. The sweet spot is selected as the nominal weld schedule The nominal weld schedule is characterized in the expected manufacturing environment. The nominal weld schedule in conjunction with process control ensures a consistent and predictable weld performance.

Materials processing in space bibliography, 1983, revised

NASA Technical Reports Server (NTRS)

Pentecost, E. (Compiler)

1983-01-01

Flight experiments utilizing a low gravity environment to elucidate and control various processes, or ground based activities that provide supporting research are compiled. Six major categories: crystal growth; solidification of metals, alloys, and composites; fluids, transports, and chemical processes; glasses and ceramics; ultrahigh vacuum and containerless processing technologies; and combustion are included. A list of patents and appendices providing a compilation of anonymously authored collections and reports and a cross reference index are included.

Grasping trajectories in a virtual environment adhere to Weber's law.

PubMed

Ozana, Aviad; Berman, Sigal; Ganel, Tzvi

2018-06-01

Virtual-reality and telerobotic devices simulate local motor control of virtual objects within computerized environments. Here, we explored grasping kinematics within a virtual environment and tested whether, as in normal 3D grasping, trajectories in the virtual environment are performed analytically, violating Weber's law with respect to object's size. Participants were asked to grasp a series of 2D objects using a haptic system, which projected their movements to a virtual space presented on a computer screen. The apparatus also provided object-specific haptic information upon "touching" the edges of the virtual targets. The results showed that grasping movements performed within the virtual environment did not produce the typical analytical trajectory pattern obtained during 3D grasping. Unlike as in 3D grasping, grasping trajectories in the virtual environment adhered to Weber's law, which indicates relative resolution in size processing. In addition, the trajectory patterns differed from typical trajectories obtained during 3D grasping, with longer times to complete the movement, and with maximum grip apertures appearing relatively early in the movement. The results suggest that grasping movements within a virtual environment could differ from those performed in real space, and are subjected to irrelevant effects of perceptual information. Such atypical pattern of visuomotor control may be mediated by the lack of complete transparency between the interface and the virtual environment in terms of the provided visual and haptic feedback. Possible implications of the findings to movement control within robotic and virtual environments are further discussed.

Geology and evolution of lakes in north-central Florida

USGS Publications Warehouse

Kindinger, J.L.; Davis, J.B.; Flocks, J.G.

1999-01-01

Fluid exchange between surficial waters and groundwater in karst environments, and the processes that control exchange, are of critical concern to water management districts and planners. High-resolution seismic data were collected from 30 lakes of north-central Florida. In each case study, lake structure and geomorphology were controlled by solution and/or mechanical processes. Processes that control lake development are twofold: (1) karstification or dissolution of the underlying limestone, and (2) the collapse, subsidence, or slumping of overburden to form sinkholes. Initial lake formation is directly related to the karst topography of the underlying host limestone. Case studies have shown that lakes can be divided by geomorphic types into progressive developmental phases: (1) active subsidence or collapse phase (young); (2) transitional phase (middle age); (3) baselevel phase (mature); and (4) polje (drowned prairie) - broad flat-bottom that have one or all phases of sinkhole. Using these criteria, Florida lakes can be classified by size, fill, subsurface features, and geomorphology.Fluid exchange between surficial waters and groundwater in karst environments, and the processes that control exchange, are of critical concern to water management districts and planners. High-resolution seismic data were collected from 30 lakes of north-central Florida. In each case study, lake structure and geomorphology were controlled by solution and/or mechanical processes. Processes that control lake development are twofold: (1) karstification or dissolution of the underlying limestone, and (2) the collapse, subsidence, or slumping of overburden to form sinkholes. Initial lake formation is directly related to the karst topography of the underlying host limestone. Case studies have shown that lakes can be divided by geomorphic types into progressive developmental phased: (1) active subsidence or collapse phase (young); (2) transitional phase (middle age); (3) baselevel phase (mature); and (4) polje (drowned prairie) - broad flat-bottom that have one or all phases of sinkhole. Using these criteria, Florida lakes can be classified by size, fill, subsurface features, and geomorphology.

Industry Speed Bumps on Local Tobacco Control in Japan? The Case of Hyogo.

PubMed

Yamada, Keiko; Mori, Nagisa; Kashiwabara, Mina; Yasuda, Sakiko; Horie, Rumi; Yamato, Hiroshi; Garçon, Loic; Armada, Francisco

2015-01-01

Despite being a signatory since 2004, Japan has not yet fully implemented Article 8 of the World Health Organization's Framework Convention on Tobacco Control regarding 100% protection against exposure to second-hand smoke (SHS). The Japanese government still recognizes designated smoking rooms (DSRs) in public space as a valid control measure. Furthermore, subnational initiatives for tobacco control in Japan are of limited effectiveness. Through an analysis of the Hyogo initiative in 2012, we identified key barriers to the achievement of a smoke-free environment. Using a descriptive case-study approach, we analyzed the smoke-free policy development process. The information was obtained from meeting minutes and other gray literature, such as public records, well as key informant interviews. Hyogo Prefecture established a committee to propose measures against SHS, and most committee members agreed with establishing completely smoke-free environments. However, the hospitality sector representatives opposed regulation, and tobacco companies were allowed to make a presentation to the committee. Further, political power shifted against completely smoke-free environments in the context of upcoming local elections, which was an obvious barrier to effective regulation. Throughout the approving process, advocacy by civil society for stronger regulation was weak. Eventually, the ordinance approved by the Prefectural Assembly was even weaker than the committee proposal and included wide exemptions. The analysis of Hyogo's SHS control initiative shed light on three factors that present challenges to implementing tobacco control regulations in Japan, from which other countries can also draw lessons: incomplete national legislation, the weakness of advocacy by the civil society, and the interference of the tobacco industry.

Effect of temperature on anodic behavior of 13Cr martensitic steel in CO2 environment

NASA Astrophysics Data System (ADS)

Zhao, G. X.; Zheng, M.; Lv, X. H.; Dong, X. H.; Li, H. L.

2005-04-01

The corrosion behavior of 13Cr martensitic stainless steel in a CO2 environment in a stimulated oilfield was studied with potentiodynamic polarization and the impedance spectra technique. The results showed that the microstructure of the surface scale clearly changed with temperature. This decreased the sensitivity of pitting corrosion and increased the tendency toward general (or uniform) corrosion. The capacitance, the charge transfer resistance, and the polarization resistance of the corrosion product scale decrease with increasing temperature from 90 to 120 °C, and thus the corrosion is a thermal activation controlled process. Charge transfer through the scale is difficult and the corrosion is controlled by a diffusion process at a temperature of 150 °C. Resistance charge transfer through the corrosion product layer is higher than that in the passive film.

Occupancy change detection system and method

DOEpatents

Bruemmer, David J [Idaho Falls, ID; Few, Douglas A [Idaho Falls, ID

2009-09-01

A robot platform includes perceptors, locomotors, and a system controller. The system controller executes instructions for producing an occupancy grid map of an environment around the robot, scanning the environment to generate a current obstacle map relative to a current robot position, and converting the current obstacle map to a current occupancy grid map. The instructions also include processing each grid cell in the occupancy grid map. Within the processing of each grid cell, the instructions include comparing each grid cell in the occupancy grid map to a corresponding grid cell in the current occupancy grid map. For grid cells with a difference, the instructions include defining a change vector for each changed grid cell, wherein the change vector includes a direction from the robot to the changed grid cell and a range from the robot to the changed grid cell.

Different carbonization process of bamboo charcoal using Gigantochloa Albociliata

NASA Astrophysics Data System (ADS)

Isa, S. S. M.; Ramli, M. M.; Halin, D. S. C.; Anhar, N. A. M.; Hambali, N. A. M. A.

2017-09-01

Bamboo charcoal has attracted a lot of interests due to their microporous structure, high surface area and great adsorption properties. Some of the applications utilizing this material focused on these advantages such as water purification, electromagnetic wave absorber and blood purification. However, these advantages really depend on the carbonization and activation process of bamboo charcoal. The production must be carried out in properly control environment with precise temperatures and timing. This paper report the production of bamboo charcoal using Gigantochloa Albociliata in controlled environment at 500 °C for 1 hour (lab-prepared). Then the material was characterized for their dispersibility and adsorption behaviour. Furthermore, the bamboo charcoal that was produced commercially, by company, was also characterized and compared. The results show, bamboo charcoal produced by lab-prepared has similar qualities with the commercial bamboo charcoal.

LLNL SFA OBER SBR FY17 Program Management and Performance Report: Subsurface Biogeochemistry of Actinides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kersting, Annie B.

A major scientific challenge in environmental sciences is to identify the dominant processes controlling actinide transport in the environment. It is estimated that currently, over 2200 metric tons of anthropogenic plutonium (Pu) has accumulated worldwide, a number that increases yearly with additional spent nuclear fuel (Ewing et al., 2010). Plutonium has been shown to migrate on the scale of kilometers, giving way to a critical concern that the fundamental biogeochemical processes that control its behavior in the subsurface are not well understood (Kersting et al. 1999; Novikov et al. 2006; Santschi et al. 2002). Neptunium (Np) is less prevalent inmore » the environment; however, it is predicted to be a significant long-term dose contributor in high-level nuclear waste. Our focus on Np chemistry in this Science Plan is intended to help formulate a better understanding of Pu redox transformations in the environment and clarify the differences between the two long-lived actinides. The research approach of our Science Plan combines (1) Fundamental Mechanistic Studies that identify and quantify biogeochemical processes that control actinide behavior in solution and on solids, (2) Field Integration Studies that investigate the transport characteristics of Pu and test our conceptual understanding of actinide transport, and (3) Actinide Research Capabilities that allow us to achieve the objectives of this Scientific Focus Area (SFA) and provide new opportunities for advancing actinide environmental chemistry. These three Research Thrusts form the basis of our SFA Science Program.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kersting, Annie B.; Zavarin, Mavrik

A major scientific challenge in environmental sciences is to identify the dominant processes controlling actinide transport in the environment. It is estimated that currently, over 2200 metric tons of plutonium (Pu) have been deposited in the subsurface worldwide, a number that increases yearly with additional spent nuclear fuel (Ewing et al., 2010). Plutonium has been shown to migrate on the scale of kilometers, giving way to a critical concern that the fundamental biogeochemical processes that control its behavior in the subsurface are not well understood (Kersting et al., 1999; Novikov et al., 2006; Santschi et al., 2002). Neptunium (Np) ismore » less prevalent in the environment; however, it is predicted to be a significant long-term dose contributor in high-level nuclear waste. Our focus on Np chemistry in this Science Plan is intended to help formulate a better understanding of Pu redox transformations in the environment and clarify the differences between the two long-lived actinides. The research approach of our Science Plan combines (1) Fundamental Mechanistic Studies that identify and quantify biogeochemical processes that control actinide behavior in solution and on solids, (2) Field Integration Studies that investigate the transport characteristics of Pu and test our conceptual understanding of actinide transport, and (3) Actinide Research Capabilities that allow us to achieve the objectives of this Scientific Focus Area (SFA and provide new opportunities for advancing actinide environmental chemistry. These three Research Thrusts form the basis of our SFA Science Program (Figure 1).« less

Using ‘appreciative inquiry’ in India to improve infection control practices in maternity care: a qualitative study

PubMed Central

Sharma, Bharati; Ramani, K.V.; Mavalankar, Dileep; Kanguru, Lovney; Hussein, Julia

2015-01-01

Background Infections acquired during childbirth are a common cause of maternal and perinatal mortality and morbidity. Changing provider behaviour and organisational settings within the health system is key to reducing the spread of infection. Objective To explore the opinions of health personnel on health system factors related to infection control and their perceptions of change in a sample of hospital maternity units. Design An organisational change process called ‘appreciative inquiry’ (AI) was introduced in three maternity units of hospitals in Gujarat, India. AI is a change process that builds on recognition of positive actions, behaviours, and attitudes. In-depth interviews were conducted with health personnel to elicit information on the environment within which they work, including physical and organisational factors, motivation, awareness, practices, perceptions of their role, and other health system factors related to infection control activities. Data were obtained from three hospitals which implemented AI and another three not involved in the intervention. Results Challenges which emerged included management processes (e.g. decision-making and problem-solving modalities), human resource shortages, and physical infrastructure (e.g. space, water, and electricity supplies). AI was perceived as having a positive influence on infection control practices. Respondents also said that management processes improved although some hospitals had already undergone an accreditation process which could have influenced the changes described. Participants reported that team relationships had been strengthened due to AI. Conclusion Technical knowledge is often emphasised in health care settings and less attention is paid to factors such as team relationships, leadership, and problem solving. AI can contribute to improving infection control by catalysing and creating forums for team building, shared decision making and problem solving in an enabling environment. PMID:26119249

Using 'appreciative inquiry' in India to improve infection control practices in maternity care: a qualitative study.

PubMed

Sharma, Bharati; Ramani, K V; Mavalankar, Dileep; Kanguru, Lovney; Hussein, Julia

2015-01-01

Infections acquired during childbirth are a common cause of maternal and perinatal mortality and morbidity. Changing provider behaviour and organisational settings within the health system is key to reducing the spread of infection. To explore the opinions of health personnel on health system factors related to infection control and their perceptions of change in a sample of hospital maternity units. An organisational change process called 'appreciative inquiry' (AI) was introduced in three maternity units of hospitals in Gujarat, India. AI is a change process that builds on recognition of positive actions, behaviours, and attitudes. In-depth interviews were conducted with health personnel to elicit information on the environment within which they work, including physical and organisational factors, motivation, awareness, practices, perceptions of their role, and other health system factors related to infection control activities. Data were obtained from three hospitals which implemented AI and another three not involved in the intervention. Challenges which emerged included management processes (e.g. decision-making and problem-solving modalities), human resource shortages, and physical infrastructure (e.g. space, water, and electricity supplies). AI was perceived as having a positive influence on infection control practices. Respondents also said that management processes improved although some hospitals had already undergone an accreditation process which could have influenced the changes described. Participants reported that team relationships had been strengthened due to AI. Technical knowledge is often emphasised in health care settings and less attention is paid to factors such as team relationships, leadership, and problem solving. AI can contribute to improving infection control by catalysing and creating forums for team building, shared decision making and problem solving in an enabling environment.

Access Control Management for SCADA Systems

NASA Astrophysics Data System (ADS)

Hong, Seng-Phil; Ahn, Gail-Joon; Xu, Wenjuan

The information technology revolution has transformed all aspects of our society including critical infrastructures and led a significant shift from their old and disparate business models based on proprietary and legacy environments to more open and consolidated ones. Supervisory Control and Data Acquisition (SCADA) systems have been widely used not only for industrial processes but also for some experimental facilities. Due to the nature of open environments, managing SCADA systems should meet various security requirements since system administrators need to deal with a large number of entities and functions involved in critical infrastructures. In this paper, we identify necessary access control requirements in SCADA systems and articulate access control policies for the simulated SCADA systems. We also attempt to analyze and realize those requirements and policies in the context of role-based access control that is suitable for simplifying administrative tasks in large scale enterprises.

Control Software for a High-Performance Telerobot

NASA Technical Reports Server (NTRS)

Kline-Schoder, Robert J.; Finger, William

2005-01-01

A computer program for controlling a high-performance, force-reflecting telerobot has been developed. The goal in designing a telerobot-control system is to make the velocity of the slave match the master velocity, and the environmental force on the master match the force on the slave. Instability can arise from even small delays in propagation of signals between master and slave units. The present software, based on an impedance-shaping algorithm, ensures stability even in the presence of long delays. It implements a real-time algorithm that processes position and force measurements from the master and slave and represents the master/slave communication link as a transmission line. The algorithm also uses the history of the control force and the slave motion to estimate the impedance of the environment. The estimate of the impedance of the environment is used to shape the controlled slave impedance to match the transmission-line impedance. The estimate of the environmental impedance is used to match the master and transmission-line impedances and to estimate the slave/environment force in order to present that force immediately to the operator via the master unit.

Learning for intelligent mobile robots

NASA Astrophysics Data System (ADS)

Hall, Ernest L.; Liao, Xiaoqun; Alhaj Ali, Souma M.

2003-10-01

Unlike intelligent industrial robots which often work in a structured factory setting, intelligent mobile robots must often operate in an unstructured environment cluttered with obstacles and with many possible action paths. However, such machines have many potential applications in medicine, defense, industry and even the home that make their study important. Sensors such as vision are needed. However, in many applications some form of learning is also required. The purpose of this paper is to present a discussion of recent technical advances in learning for intelligent mobile robots. During the past 20 years, the use of intelligent industrial robots that are equipped not only with motion control systems but also with sensors such as cameras, laser scanners, or tactile sensors that permit adaptation to a changing environment has increased dramatically. However, relatively little has been done concerning learning. Adaptive and robust control permits one to achieve point to point and controlled path operation in a changing environment. This problem can be solved with a learning control. In the unstructured environment, the terrain and consequently the load on the robot"s motors are constantly changing. Learning the parameters of a proportional, integral and derivative controller (PID) and artificial neural network provides an adaptive and robust control. Learning may also be used for path following. Simulations that include learning may be conducted to see if a robot can learn its way through a cluttered array of obstacles. If a situation is performed repetitively, then learning can also be used in the actual application. To reach an even higher degree of autonomous operation, a new level of learning is required. Recently learning theories such as the adaptive critic have been proposed. In this type of learning a critic provides a grade to the controller of an action module such as a robot. The creative control process is used that is "beyond the adaptive critic." A mathematical model of the creative control process is presented that illustrates the use for mobile robots. Examples from a variety of intelligent mobile robot applications are also presented. The significance of this work is in providing a greater understanding of the applications of learning to mobile robots that could lead to many applications.

Digital Environment for Movement Control in Surgical Skill Training.

PubMed

Juanes, Juan A; Gómez, Juan J; Peguero, Pedro D; Ruisoto, Pablo

2016-06-01

Intelligent environments are increasingly becoming useful scenarios for handling computers. Technological devices are practical tools for learning and acquiring clinical skills as part of the medical training process. Within the framework of the advanced user interface, we present a technological application using Leap Motion, to enhance interaction with the user in the process of a laparoscopic surgical intervention and integrate the navigation through augmented reality images using manual gestures. Thus, we intend to achieve a more natural interaction with the objects that participate in a surgical intervention, which are augmented and related to the user's hand movements.

A Process Management System for Networked Manufacturing

NASA Astrophysics Data System (ADS)

Liu, Tingting; Wang, Huifen; Liu, Linyan

With the development of computer, communication and network, networked manufacturing has become one of the main manufacturing paradigms in the 21st century. Under the networked manufacturing environment, there exist a large number of cooperative tasks susceptible to alterations, conflicts caused by resources and problems of cost and quality. This increases the complexity of administration. Process management is a technology used to design, enact, control, and analyze networked manufacturing processes. It supports efficient execution, effective management, conflict resolution, cost containment and quality control. In this paper we propose an integrated process management system for networked manufacturing. Requirements of process management are analyzed and architecture of the system is presented. And a process model considering process cost and quality is developed. Finally a case study is provided to explain how the system runs efficiently.

Shorter Life Span of Microorganisms and Plants as a Consequence of Shielded Magnetic Environment

NASA Astrophysics Data System (ADS)

Dobrota, C.; Piso, I. M.; Bathory, D.

The geomagnetic field is an essential environmental factor for life and health on this planet. In order to survey how magnetic fields affect the life span and the nitrogenase (an iron-sulphur enzyme) activity of Azotobacter chroococcum as well as the life span, the main organic synthesis and the water balance of plants (22 species), the biological tests were incubated under shielded magnetic field and also in normal geo-magnetic environment. The shielding level was about 10-6 of the terrestrial magnetic field.Life cycles of all organisms require the co-ordinated control of a complex set of interlocked physiological processes and metabolic pathways. Such processes are likely to be regulated by a large number of genes. Our researches suggest that the main point in biological structures, which seems to be affected by the low magnetic environment, is the water molecule. Magnetic field induces a molecular alignment. Under shielded conditions, unstructured water molecules with fewer hydrogen bonds, which are producing a more reactive environment, are occurring. As compared to control, the life span of both microorganisms and plants was shorter in shielded environment. A higher nitrogenase affinity for the substrate was recorded in normal geo-magnetic field compared to low magnetic field. The synthesis of carbohydrates, lipids, proteins and enzymes was modified under experimental conditions. The stomatal conductance was higher between 158 and 300% in shielded environment indicating an important water loss from the plant cells.Our results support the idea that the shielded magnetic environment induces different reactions depending on the time of exposure and on the main metabolic pathways of the cells.

Intelligent control based on fuzzy logic and neural net theory

NASA Technical Reports Server (NTRS)

Lee, Chuen-Chien

1991-01-01

In the conception and design of intelligent systems, one promising direction involves the use of fuzzy logic and neural network theory to enhance such systems' capability to learn from experience and adapt to changes in an environment of uncertainty and imprecision. Here, an intelligent control scheme is explored by integrating these multidisciplinary techniques. A self-learning system is proposed as an intelligent controller for dynamical processes, employing a control policy which evolves and improves automatically. One key component of the intelligent system is a fuzzy logic-based system which emulates human decision making behavior. It is shown that the system can solve a fairly difficult control learning problem. Simulation results demonstrate that improved learning performance can be achieved in relation to previously described systems employing bang-bang control. The proposed system is relatively insensitive to variations in the parameters of the system environment.

Distributed Motor Controller (DMC) for Operation in Extreme Environments

NASA Technical Reports Server (NTRS)

McKinney, Colin M.; Yager, Jeremy A.; Mojarradi, Mohammad M.; Some, Rafi; Sirota, Allen; Kopf, Ted; Stern, Ryan; Hunter, Don

2012-01-01

This paper presents an extreme environment capable Distributed Motor Controller (DMC) module suitable for operation with a distributed architecture of future spacecraft systems. This motor controller is designed to be a bus-based electronics module capable of operating a single Brushless DC motor in extreme space environments: temperature (-120 C to +85 C required, -180 C to +100 C stretch goal); radiation (>;20K required, >;100KRad stretch goal); >;360 cycles of operation. Achieving this objective will result in a scalable modular configuration for motor control with enhanced reliability that will greatly lower cost during the design, fabrication and ATLO phases of future missions. Within the heart of the DMC lies a pair of cold-capable Application Specific Integrated Circuits (ASICs) and a Field Programmable Gate Array (FPGA) that enable its miniaturization and operation in extreme environments. The ASICs are fabricated in the IBM 0.5 micron Silicon Germanium (SiGe) BiCMOS process and are comprised of Analog circuitry to provide telemetry information, sensor interface, and health and status of DMC. The FPGA contains logic to provide motor control, status monitoring and spacecraft interface. The testing and characterization of these ASICs have yielded excellent functionality in cold temperatures (-135 C). The DMC module has demonstrated successful operation of a motor at temperature.

Elimination of volatile organic compounds by biofiltration: a review.

PubMed

Nikiema, Josiane; Dastous, Paul-André; Heitz, Michèle

2007-01-01

Volatile organic compounds (VOCs) are pollutants that are responsible for the formation of the tropospheric ozone, one of the precursors of smog. VOCs are emitted by various industries including chemical plants, pulp and paper mills, pharmaceuticals, cosmetics, electronics and agri-food industries. Some VOCs cause odor pollution while many of them are harmful to environment and human or animal health. For the removal of VOCs, biofiltration, a biological process, has proved to be reliable when properly operated. This process has therefore been widely applied in Europe and North America. The main advantages associated with the use of biofiltration are related to its set-up, maintenance, and operating costs which are usually lower than those related to other VOCs control technologies and because it is less harmful for the environment than conventional processes like incineration. In the present paper, the main parameters (type, moisture, pH, and temperature of filter bed, microbial population, nutrients concentrations, and VOCs' inlet load) to be controlled during the biofiltration are identified and described in detail. The main phenomena involved in biofiltration are also discussed. For improving the efficiency of VOC control biotechnology, new techniques are now proposed that include the use of membranes, biphasic reactors, UV photolysis, and many others.

Pathogen survival trajectories: an eco-environmental approach to the modeling of human campylobacteriosis ecology.

PubMed Central

Skelly, Chris; Weinstein, Phil

2003-01-01

Campylobacteriosis, like many human diseases, has its own ecology in which the propagation of human infection and disease depends on pathogen survival and finding new hosts in order to replicate and sustain the pathogen population. The complexity of this process, a process common to other enteric pathogens, has hampered control efforts. Many unknowns remain, resulting in a poorly understood disease ecology. To provide structure to these unknowns and help direct further research and intervention, we propose an eco-environmental modeling approach for campylobacteriosis. This modeling approach follows the pathogen population as it moves through the environments that define the physical structure of its ecology. In this paper, we term the ecologic processes and environments through which these populations move "pathogen survival trajectories." Although such a modeling approach could have veterinary applications, our emphasis is on human campylobacteriosis and focuses on human exposures to Campylobacter through feces, food, and aquatic environments. The pathogen survival trajectories that lead to human exposure include ecologic filters that limit population size, e.g., cooking food to kill Campylobacter. Environmental factors that influence the size of the pathogen reservoirs include temperature, nutrient availability, and moisture availability during the period of time the pathogen population is moving through the environment between infected and susceptible hosts. We anticipate that the modeling approach proposed here will work symbiotically with traditional epidemiologic and microbiologic research to help guide and evaluate the acquisition of new knowledge about the ecology, eventual intervention, and control of campylobacteriosis. PMID:12515674

From instinct to intellect: the challenge of maintaining healthy weight in the modern world.

PubMed

Peters, J C; Wyatt, H R; Donahoo, W T; Hill, J O

2002-05-01

The global obesity epidemic is being driven in large part by a mismatch between our environment and our metabolism. Human physiology developed to function within an environment where high levels of physical activity were needed in daily life and food was inconsistently available. For most of mankind's history, physical activity has 'pulled' appetite so that the primary challenge to the physiological system for body weight control was to obtain sufficient energy intake to prevent negative energy balance and body energy loss. The current environment is characterized by a situation whereby minimal physical activity is required for daily life and food is abundant, inexpensive, high in energy density and widely available. Within this environment, food intake 'pushes' the system, and the challenge to the control system becomes to increase physical activity sufficiently to prevent positive energy balance. There does not appear to be a strong drive to increase physical activity in response to excess energy intake and there appears to be only a weak adaptive increase in resting energy expenditure in response to excess energy intake. In the modern world, the prevailing environment constitutes a constant background pressure that promotes weight gain. We propose that the modern environment has taken body weight control from an instinctual (unconscious) process to one that requires substantial cognitive effort. In the current environment, people who are not devoting substantial conscious effort to managing body weight are probably gaining weight. It is unlikely that we would be able to build the political will to undo our modern lifestyle, to change the environment back to one in which body weight control again becomes instinctual. In order to combat the growing epidemic we should focus our efforts on providing the knowledge, cognitive skills and incentives for controlling body weight and at the same time begin creating a supportive environment to allow better management of body weight.

Controls and variability of solute and sedimentary fluxes in Antarctic and sub-Antarctic Environments

NASA Astrophysics Data System (ADS)

Zwolinski, Zbigniew

2015-04-01

The currently prepared SEDIBUD Book on "Source-to-Sink Fluxes in Undisturbed Cold Environments" (edited by Achim A. Beylich, John C. Dixon and Zbigniew Zwolinski and published by Cambridge University Press) is summarizing and synthesizing the achievements of the International Association of Geomorphologists` (I.A.G./A.I.G.) Working Group SEDIBUD (Sediment Budgets in Cold Environments), which has been active since 2005 (http://www.geomorph.org/wg/wgsb.html). The book comprises five parts. One of them is part about sub-Antarctic and Antarctic Environments. This part "Sub-Antarctic and Antarctic Environments" describes two different environments, namely oceanic and continental ones. Each part contains results of research on environmental drivers and rates of contemporary solute and sedimentary fluxes in selected sites. Apart from describing the environmental conditions of the whole continent of Antarctica and sub-Antarctic islands (Zb.Zwolinski, M.Kejna, A.N.Lastochkin, A.Zhirov, S.Boltramovich) this part of the book characterizes terrestrial polar oases free from multi-year ice and snow covers (Zb.Zwolinski). The detailed results of geoecological and sedimentological research come from different parts of Antarctica. Antarctic continental shelf (E.Isla) is an example of sub-Antarctic oceanic environment. South Shetlands, especially King George Island (Zb.Zwolinski, M.Kejna, G.Rachlewicz, I.Sobota, J.Szpikowski), is an example of sub-Antarctic terrestrial environment. Antarctic Peninsula (G.Vieira, M.Francelino, J.C.Fernandes) and surroundings of McMurdo Dry Valleys (W.B.Lyons, K.A.Welch, J.Levy, A.Fountain, D.McKnight) are examples of Antarctic continental environments. The key goals of the Antarctic and sub-Antarctic book chapters are following: (i) identify the main environmental drivers and rates of contemporary solute and sedimentary fluxes, and (ii) model possible effects of projected climate change on solute and sedimentary fluxes in cold climate environments. Solute and sediment transport in the streams of analyzed environments are constrained by the relatively short water runoff season that typically lasts from a few weeks to maximum of four months during the austral summer, for Antarctic and sub-Antarctic regions respectively. Because of high intensity of mechanical and chemical weathering processes solute and sediment transport are rather high within Antarctic environments. Weathering rates on slopes and magnitude of fluvial transport in relatively short streams control the intensity of denudational processes. Both mechanical and chemical denudation varies highly through sub-Antarctic and Antarctic environments. To generate accurate predictions of fluvial and denudational processes we must fully understand the actual geoecological processes, which in some places are under rapid change, e.g., the Antarctic Peninsula and sub-Antarctic islands.

Enrichment of Human-Computer Interaction in Brain-Computer Interfaces via Virtual Environments

PubMed Central

Víctor Rodrigo, Mercado-García

2017-01-01

Tridimensional representations stimulate cognitive processes that are the core and foundation of human-computer interaction (HCI). Those cognitive processes take place while a user navigates and explores a virtual environment (VE) and are mainly related to spatial memory storage, attention, and perception. VEs have many distinctive features (e.g., involvement, immersion, and presence) that can significantly improve HCI in highly demanding and interactive systems such as brain-computer interfaces (BCI). BCI is as a nonmuscular communication channel that attempts to reestablish the interaction between an individual and his/her environment. Although BCI research started in the sixties, this technology is not efficient or reliable yet for everyone at any time. Over the past few years, researchers have argued that main BCI flaws could be associated with HCI issues. The evidence presented thus far shows that VEs can (1) set out working environmental conditions, (2) maximize the efficiency of BCI control panels, (3) implement navigation systems based not only on user intentions but also on user emotions, and (4) regulate user mental state to increase the differentiation between control and noncontrol modalities. PMID:29317861

Investigation of microgravity effects on solidification phenomena of selected materials

NASA Technical Reports Server (NTRS)

Maag, Carl R.; Hansen, Patricia A.

1992-01-01

A Get Away Special (GAS) experiment payload to investigate microgravity effects on solidification phenomena of selected experimental samples has been designed for flight. It is intended that the first flight of the assembly will (1) study the p-n junction characteristics for advancing semiconductor device applications, (2) study the effects of gravity-driven convection on the growth of HgCd crystals, (3) compare the textures of the sample which crystallizes in microgravity with those found in chondrite meteorites, and (4) modify glass optical characteristics through divalent oxygen exchange. The space flight experiment consists of many small furnaces. While the experiment payload is in the low gravity environment of orbital flight, the payload controller will sequentially activate the furnaces to heat samples to their melt state and then allow cooling to resolidification in a controlled fashion. The materials processed in the microgravity environment of space will be compared to the same materials processed on earth in a one-gravity environment. This paper discusses the design of all subassemblies (furnance, electronics, and power systems) in the experiment. A complete description of the experimental materials is also presented.

Occurrence of Alicyclobacillus in the fruit processing environment--a review.

PubMed

Steyn, Catharina E; Cameron, Michelle; Witthuhn, R Corli

2011-05-14

Concentrated fruit products have a significant place in modern consumption markets and are valuable semi-prepared food components to the bakery, dairy, confectionary, canning, baby food, frozen food, distilling and beverage industries. There is continuous pressure on the beverage industry to improve the quality of concentrated fruit products in order for reconstituted fruit beverages to compete with beverages that are made from fresh fruits. In recent years, Alicyclobacillus spp. have become a major concern to the beverage industry worldwide as many high-acid, concentrated fruit products have been found to be contaminated with these spoilage microbes. The thermo-acidophilic nature of alicyclobacilli and highly resistant endospores allows for their survival during the production of concentrated fruit products. Under favourable conditions, endospores can germinate and multiply to numbers high enough to cause spoilage and product deterioration through the production of chemical taint compounds. It is imperative to understand the nature of Alicyclobacillus within the fruit concentrate processing environment so as to develop effective control strategies and to prevent spoilage in juice and beverage products that are reconstituted from fruit concentrates. This paper reviews the occurrence of alicyclobacilli in the fruit processing environment, control measures, as well as detection, identification and standardised test methods that are currently used for Alicyclobacillus in concentrated fruit products. Copyright © 2011 Elsevier B.V. All rights reserved.

Surgical model-view-controller simulation software framework for local and collaborative applications

PubMed Central

Sankaranarayanan, Ganesh; Halic, Tansel; Arikatla, Venkata Sreekanth; Lu, Zhonghua; De, Suvranu

2010-01-01

Purpose Surgical simulations require haptic interactions and collaboration in a shared virtual environment. A software framework for decoupled surgical simulation based on a multi-controller and multi-viewer model-view-controller (MVC) pattern was developed and tested. Methods A software framework for multimodal virtual environments was designed, supporting both visual interactions and haptic feedback while providing developers with an integration tool for heterogeneous architectures maintaining high performance, simplicity of implementation, and straightforward extension. The framework uses decoupled simulation with updates of over 1,000 Hz for haptics and accommodates networked simulation with delays of over 1,000 ms without performance penalty. Results The simulation software framework was implemented and was used to support the design of virtual reality-based surgery simulation systems. The framework supports the high level of complexity of such applications and the fast response required for interaction with haptics. The efficacy of the framework was tested by implementation of a minimally invasive surgery simulator. Conclusion A decoupled simulation approach can be implemented as a framework to handle simultaneous processes of the system at the various frame rates each process requires. The framework was successfully used to develop collaborative virtual environments (VEs) involving geographically distributed users connected through a network, with the results comparable to VEs for local users. PMID:20714933

Surgical model-view-controller simulation software framework for local and collaborative applications.

PubMed

Maciel, Anderson; Sankaranarayanan, Ganesh; Halic, Tansel; Arikatla, Venkata Sreekanth; Lu, Zhonghua; De, Suvranu

2011-07-01

Surgical simulations require haptic interactions and collaboration in a shared virtual environment. A software framework for decoupled surgical simulation based on a multi-controller and multi-viewer model-view-controller (MVC) pattern was developed and tested. A software framework for multimodal virtual environments was designed, supporting both visual interactions and haptic feedback while providing developers with an integration tool for heterogeneous architectures maintaining high performance, simplicity of implementation, and straightforward extension. The framework uses decoupled simulation with updates of over 1,000 Hz for haptics and accommodates networked simulation with delays of over 1,000 ms without performance penalty. The simulation software framework was implemented and was used to support the design of virtual reality-based surgery simulation systems. The framework supports the high level of complexity of such applications and the fast response required for interaction with haptics. The efficacy of the framework was tested by implementation of a minimally invasive surgery simulator. A decoupled simulation approach can be implemented as a framework to handle simultaneous processes of the system at the various frame rates each process requires. The framework was successfully used to develop collaborative virtual environments (VEs) involving geographically distributed users connected through a network, with the results comparable to VEs for local users.

Space Vehicle Terrestrial Environment Design Requirements Guidelines

NASA Technical Reports Server (NTRS)

Johnson, Dale L.; Keller, Vernon W.; Vaughan, William W.

2006-01-01

The terrestrial environment is an important driver of space vehicle structural, control, and thermal system design. NASA is currently in the process of producing an update to an earlier Terrestrial Environment Guidelines for Aerospace Vehicle Design and Development Handbook. This paper addresses the contents of this updated handbook, with special emphasis on new material being included in the areas of atmospheric thermodynamic models, wind dynamics, atmospheric composition, atmospheric electricity, cloud phenomena, atmospheric extremes, and sea state. In addition, the respective engineering design elements are discussed relative to terrestrial environment inputs that require consideration. Specific lessons learned that have contributed to the advancements made in the application and awareness of terrestrial environment inputs for aerospace engineering applications are presented.

The Impact of Meteoroid Streams on the Lunar Atmosphere and Dust Environment During the LADEE Mission

NASA Technical Reports Server (NTRS)

Stubbs, T. J.; Glenar, D. A.; Wang, Y.; Hermalyn, B.; Sarantos, M.; Colaprete, A.; Elphic, R. C.

2015-01-01

The scientific objectives of the Lunar Atmosphere and Dust Environment Explorer (LADEE) mission are: (1) determine the composition of the lunar atmosphere, investigate processes controlling distribution and variability - sources, sinks, and surface interactions; and (2) characterize the lunar exospheric dust environment, measure spatial and temporal variability, and influences on the lunar atmosphere. Impacts on the lunar surface from meteoroid streams encountered by the Earth-Moon system are anticipated to result in enhancements in the both the lunar atmosphere and dust environment. Here we describe the annual meteoroid streams expected to be incident at the Moon during the LADEE mission, and their anticipated effects on the lunar environment.

40 CFR 763.173 - Exemptions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Prohibition of the Manufacture, Importation, Processing, and Distribution in Commerce of Certain Asbestos... Pennsylvania Ave., NW., Washington, DC 20460, ATTENTION: Asbestos Exemption. For information regarding the...

Human Engineering of Space Vehicle Displays and Controls

NASA Technical Reports Server (NTRS)

Whitmore, Mihriban; Holden, Kritina L.; Boyer, Jennifer; Stephens, John-Paul; Ezer, Neta; Sandor, Aniko

2010-01-01

Proper attention to the integration of the human needs in the vehicle displays and controls design process creates a safe and productive environment for crew. Although this integration is critical for all phases of flight, for crew interfaces that are used during dynamic phases (e.g., ascent and entry), the integration is particularly important because of demanding environmental conditions. This panel addresses the process of how human engineering involvement ensures that human-system integration occurs early in the design and development process and continues throughout the lifecycle of a vehicle. This process includes the development of requirements and quantitative metrics to measure design success, research on fundamental design questions, human-in-the-loop evaluations, and iterative design. Processes and results from research on displays and controls; the creation and validation of usability, workload, and consistency metrics; and the design and evaluation of crew interfaces for NASA's Crew Exploration Vehicle are used as case studies.

An integrated toolbox for processing and analysis of remote sensing data of inland and coastal waters - atmospheric correction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haan, J.F. de; Kokke, J.M.M.; Hoogenboom, H.J.

1997-06-01

Deriving thematic maps of water quality parameters from a remote sensing image requires a number of processing steps, such as calibration, atmospheric correction, air-water interface correction, and application of water quality algorithms. A prototype version of an integrated software environment has recently been developed that enables the user to perform and control these processing steps. Major parts of this environment are: (i) access to the MODTRAN 3 radiative transfer code, (ii) a database of water quality algorithms, and (iii) a spectral library of Dutch coastal and inland waters, containing subsurface irradiance reflectance spectra and associated water quality parameters. The atmosphericmore » correction part of this environment is discussed here. It is shown that this part can be used to accurately retrieve spectral signatures of inland water for wavelengths between 450 and 750 nm, provided in situ measurements are used to determine atmospheric model parameters. Assessment of the usefulness of the completely integrated software system in an operational environment requires a revised version that is presently being developed.« less

Synthetic control of a fitness tradeoff in yeast nitrogen metabolism

PubMed Central

Bayer, Travis S; Hoff, Kevin G; Beisel, Chase L; Lee, Jack J; Smolke, Christina D

2009-01-01

Background Microbial communities are involved in many processes relevant to industrial and medical biotechnology, such as the formation of biofilms, lignocellulosic degradation, and hydrogen production. The manipulation of synthetic and natural microbial communities and their underlying ecological parameters, such as fitness, evolvability, and variation, is an increasingly important area of research for synthetic biology. Results Here, we explored how synthetic control of an endogenous circuit can be used to regulate a tradeoff between fitness in resource abundant and resource limited environments in a population of Saccharomyces cerevisiae. We found that noise in the expression of a key enzyme in ammonia assimilation, Gdh1p, mediated a tradeoff between growth in low nitrogen environments and stress resistance in high ammonia environments. We implemented synthetic control of an endogenous Gdh1p regulatory network to construct an engineered strain in which the fitness of the population was tunable in response to an exogenously-added small molecule across a range of ammonia environments. Conclusion The ability to tune fitness and biological tradeoffs will be important components of future efforts to engineer microbial communities. PMID:19118500

Controlling the Didactic Relation: A Case in Process Engineering Education

ERIC Educational Resources Information Center

Jaako, Juha

2014-01-01

A case study was conducted during 1994-2013 on several groups of process engineering students to see what was needed to transform a single course from a teacher-centred to a student-centred learning environment (SCLE). Development work was done incrementally, using Herbart's didactic triangle as a theoretical framework. The effects of the…

Aerospace vehicle water-waste management

NASA Technical Reports Server (NTRS)

Pecoraro, J. N.

1973-01-01

The collection and disposal of human wastes, such as urine and feces, in a spacecraft environment are performed in an aesthetic and reliable manner to prevent degradation of crew performance. The waste management system controls, transfers, and processes materials such as feces, emesis, food residues, used expendables, and other wastes. The requirements, collection, transport, and waste processing are described.

Tacit Quality Leadership: Operationalized Quality Perceptions as a Source of Influence in the American Higher Education Accreditation Process

ERIC Educational Resources Information Center

Saurbier, Ann L.

2013-01-01

American post-secondary education faces unprecedented challenges in the dynamic 21st century environment. An appreciation of the higher education accreditation process, as a quality control mechanism, therefore may be seen as a significant priority. When American higher education is viewed systemically, the perceptions of quality held and…

Embryological Development: Evolutionary History, Genetic Bias, and Cellular Environment Control the Flow of Developmental Events. Part I.

ERIC Educational Resources Information Center

Caplan, Arnold I.

1981-01-01

Describes development of the limb and various interactions necessary for the expression of its unique form and phenotypes to uncover the hierarchical controlling steps in the development process for the potential of avoiding abnormal events and manipulating what might be detrimental genetic events into a normal sequence. (Author/SK)

40 CFR 415.67 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... control technology (BCT). 415.67 Section 415.67 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... conventional pollutant control technology (BCT). (a) Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart and using the mercury cell process must achieve the following...

Hybrid photonic signal processing

NASA Astrophysics Data System (ADS)

Ghauri, Farzan Naseer

This thesis proposes research of novel hybrid photonic signal processing systems in the areas of optical communications, test and measurement, RF signal processing and extreme environment optical sensors. It will be shown that use of innovative hybrid techniques allows design of photonic signal processing systems with superior performance parameters and enhanced capabilities. These applications can be divided into domains of analog-digital hybrid signal processing applications and free-space---fiber-coupled hybrid optical sensors. The analog-digital hybrid signal processing applications include a high-performance analog-digital hybrid MEMS variable optical attenuator that can simultaneously provide high dynamic range as well as high resolution attenuation controls; an analog-digital hybrid MEMS beam profiler that allows high-power watt-level laser beam profiling and also provides both submicron-level high resolution and wide area profiling coverage; and all optical transversal RF filters that operate on the principle of broadband optical spectral control using MEMS and/or Acousto-Optic tunable Filters (AOTF) devices which can provide continuous, digital or hybrid signal time delay and weight selection. The hybrid optical sensors presented in the thesis are extreme environment pressure sensors and dual temperature-pressure sensors. The sensors employ hybrid free-space and fiber-coupled techniques for remotely monitoring a system under simultaneous extremely high temperatures and pressures.

Microphone Array Phased Processing System (MAPPS): Version 4.0 Manual

NASA Technical Reports Server (NTRS)

Watts, Michael E.; Mosher, Marianne; Barnes, Michael; Bardina, Jorge

1999-01-01

A processing system has been developed to meet increasing demands for detailed noise measurement of individual model components. The Microphone Array Phased Processing System (MAPPS) uses graphical user interfaces to control all aspects of data processing and visualization. The system uses networked parallel computers to provide noise maps at selected frequencies in a near real-time testing environment. The system has been successfully used in the NASA Ames 7- by 10-Foot Wind Tunnel.

Friction Stir Process Mapping Methodology

NASA Technical Reports Server (NTRS)

Kooney, Alex; Bjorkman, Gerry; Russell, Carolyn; Smelser, Jerry (Technical Monitor)

2002-01-01

In FSW (friction stir welding), the weld process performance for a given weld joint configuration and tool setup is summarized on a 2-D plot of RPM vs. IPM. A process envelope is drawn within the map to identify the range of acceptable welds. The sweet spot is selected as the nominal weld schedule. The nominal weld schedule is characterized in the expected manufacturing environment. The nominal weld schedule in conjunction with process control ensures a consistent and predictable weld performance.

AGARD Flight Test Instrumentation Series. Volume 14. The Analysis of Random Data

DTIC Science & Technology

1981-11-01

obtained at arbitrary times during a number of flights. No constraints have been placed upon the controlling parameters, so that the process is non ...34noisy" environment controlling a non -linear system (the aircraft) using a redundant net of control parameters. when aircraft were flown manually with...structure. Cuse 2. Non -Stationary Measurements. When the 114S value of a random signal varies with parameters which cannot be controlled , then the method

Parallel plan execution with self-processing networks

NASA Technical Reports Server (NTRS)

Dautrechy, C. Lynne; Reggia, James A.

1989-01-01

A critical issue for space operations is how to develop and apply advanced automation techniques to reduce the cost and complexity of working in space. In this context, it is important to examine how recent advances in self-processing networks can be applied for planning and scheduling tasks. For this reason, the feasibility of applying self-processing network models to a variety of planning and control problems relevant to spacecraft activities is being explored. Goals are to demonstrate that self-processing methods are applicable to these problems, and that MIRRORS/II, a general purpose software environment for implementing self-processing models, is sufficiently robust to support development of a wide range of application prototypes. Using MIRRORS/II and marker passing modelling techniques, a model of the execution of a Spaceworld plan was implemented. This is a simplified model of the Voyager spacecraft which photographed Jupiter, Saturn, and their satellites. It is shown that plan execution, a task usually solved using traditional artificial intelligence (AI) techniques, can be accomplished using a self-processing network. The fact that self-processing networks were applied to other space-related tasks, in addition to the one discussed here, demonstrates the general applicability of this approach to planning and control problems relevant to spacecraft activities. It is also demonstrated that MIRRORS/II is a powerful environment for the development and evaluation of self-processing systems.

The Human-Electronic Crew: Is the Team Maturing? Joint GAF/RAF/USAF workshop on Human-Electronic Crew Teamwork (2nd) Held in Ingolstadt, Germany on September 25-28, 1990

DTIC Science & Technology

1992-07-10

a way ahead for future work to explore the cognitive nature of the whole command and control task and a decision support environment . Introduction...existing inferior approach. Second, the nature of how tasks are performed changes in a dynamic environment . For example, the decision-making process...the system must be designed to perform in its expected operational environment . It includes tasks performed by the aircraft, its systems, and each of

Polymeric materials science in the microgravity environment

NASA Technical Reports Server (NTRS)

Coulter, Daniel R.

1989-01-01

The microgravity environment presents some interesting possibilities for the study of polymer science. Properties of polymeric materials depend heavily on their processing history and environment. Thus, there seem to be some potentially interesting and useful new materials that could be developed. The requirements for studying polymeric materials are in general much less rigorous than those developed for studying metals, for example. Many of the techniques developed for working with other materials, including heat sources, thermal control hardware and noncontact temperature measurement schemes should meet the needs of the polymer scientist.

3D multiplayer virtual pets game using Google Card Board

NASA Astrophysics Data System (ADS)

Herumurti, Darlis; Riskahadi, Dimas; Kuswardayan, Imam

2017-08-01

Virtual Reality (VR) is a technology which allows user to interact with the virtual environment. This virtual environment is generated and simulated by computer. This technology can make user feel the sensation when they are in the virtual environment. The VR technology provides real virtual environment view for user and it is not viewed from screen. But it needs another additional device to show the view of virtual environment. This device is known as Head Mounted Device (HMD). Oculust Rift and Microsoft Hololens are the most famous HMD devices used in VR. And in 2014, Google Card Board was introduced at Google I/O developers conference. Google Card Board is VR platform which allows user to enjoy the VR with simple and cheap way. In this research, we explore Google Card Board to develop simulation game of raising pet. The Google Card Board is used to create view for the VR environment. The view and control in VR environment is built using Unity game engine. And the simulation process is designed using Finite State Machine (FSM). This FSM can help to design the process clearly. So the simulation process can describe the simulation of raising pet well. Raising pet is fun activity. But sometimes, there are many conditions which cause raising pet become difficult to do, i.e. environment condition, disease, high cost, etc. this research aims to explore and implement Google Card Board in simulation of raising pet.

Developments in Test Facility and Data Networking for the Altitude Test Stand at the John C. Stennis Space Center: A General Overview

NASA Technical Reports Server (NTRS)

Hebert, Phillip W.

2008-01-01

NASA/SSC's Mission in Rocket Propulsion Testing Is to Acquire Test Performance Data for Verification, Validation and Qualification of Propulsion Systems Hardware: Accurate, Reliable, Comprehensive, and Timely. Data Acquisition in a Rocket Propulsion Test Environment Is Challenging: a) Severe Temporal Transient Dynamic Environments; b) Large Thermal Gradients; c) Vacuum to high pressure regimes. A-3 Test Stand Development is equally challenging with respect to accommodating vacuum environment, operation of a CSG system, and a large quantity of data system and control channels to determine proper engine performance as well as Test Stand operation. SSC is currently in the process of providing modernized DAS, Control Systems, Video, and network systems for the A-3 Test Stand to overcome these challenges.

On-Board Mining in the Sensor Web

NASA Astrophysics Data System (ADS)

Tanner, S.; Conover, H.; Graves, S.; Ramachandran, R.; Rushing, J.

2004-12-01

On-board data mining can contribute to many research and engineering applications, including natural hazard detection and prediction, intelligent sensor control, and the generation of customized data products for direct distribution to users. The ability to mine sensor data in real time can also be a critical component of autonomous operations, supporting deep space missions, unmanned aerial and ground-based vehicles (UAVs, UGVs), and a wide range of sensor meshes, webs and grids. On-board processing is expected to play a significant role in the next generation of NASA, Homeland Security, Department of Defense and civilian programs, providing for greater flexibility and versatility in measurements of physical systems. In addition, the use of UAV and UGV systems is increasing in military, emergency response and industrial applications. As research into the autonomy of these vehicles progresses, especially in fleet or web configurations, the applicability of on-board data mining is expected to increase significantly. Data mining in real time on board sensor platforms presents unique challenges. Most notably, the data to be mined is a continuous stream, rather than a fixed store such as a database. This means that the data mining algorithms must be modified to make only a single pass through the data. In addition, the on-board environment requires real time processing with limited computing resources, thus the algorithms must use fixed and relatively small amounts of processing time and memory. The University of Alabama in Huntsville is developing an innovative processing framework for the on-board data and information environment. The Environment for On-Board Processing (EVE) and the Adaptive On-board Data Processing (AODP) projects serve as proofs-of-concept of advanced information systems for remote sensing platforms. The EVE real-time processing infrastructure will upload, schedule and control the execution of processing plans on board remote sensors. These plans provide capabilities for autonomous data mining, classification and feature extraction using both streaming and buffered data sources. A ground-based testbed provides a heterogeneous, embedded hardware and software environment representing both space-based and ground-based sensor platforms, including wireless sensor mesh architectures. The AODP project explores the EVE concepts in the world of sensor-networks, including ad-hoc networks of small sensor platforms.

The transitional depositional environment and sequence stratigraphy of Chasma Boreale

NASA Astrophysics Data System (ADS)

Brothers, S. C.; Kocurek, G.

2018-07-01

The depositional system within Chasma Boreale is unique in that it contains active aeolian environments, expressed as dune fields, and active cryosphere environments, present as layered ice deposits, as well as environments that transition between these. This work presents a new analysis of the Chasma Boreale sediment system that creates an interpretative framework addressing: (a) controls on the balance between aeolian and cryospheric processes in the modern depositional system, (b) the stratigraphic architecture of related sedimentary deposits, and (c) processes of sediment accumulation and preservation. Images from Context Camera (CTX; 6 m/pixel) are used to classify and map sedimentary environments, surfaces, and deposits on the reentrant floor, to refine the established geologic map of the reentrant, and to infer the stratigraphic record of the accumulation from Chasma Boreale's depositional system. A spectrum of sedimentary environments occurring between those dominated by aeolian and by cryospheric processes are identified. Through time, the boundaries of these sedimentary environments have shifted, resulting in complex lateral changes in the configuration of sedimentary environments on the reentrant's floor. Vertically, the stratigraphic record is characterized by the punctuation of sandy aeolian deposits by icy surfaces that indicate episodes of ice growth that preserve underlying deposits, resulting in accumulation. Stabilized icy surfaces occur at multiple vertical (temporal) scales and lateral extents, suggesting the influence of both regional climate change due to allogenic forcing, as well as autogenic dynamics within the transitional system. These observations demonstrate that the Chasma Boreale accumulation can be interpreted in an aeolian sequence stratigraphic framework. This work contributes the first detailed description of the processes forming polar aeolian sequences, with an emphasis on the competing and complementary dynamics between aeolian and cryospheric systems.

Lifelong Transfer Learning for Heterogeneous Teams of Agents in Sequential Decision Processes

DTIC Science & Technology

2016-06-01

making (SDM) tasks in dynamic environments with simulated and physical robots . 15. SUBJECT TERMS Sequential decision making, lifelong learning, transfer...sequential decision-making (SDM) tasks in dynamic environments with both simple benchmark tasks and more complex aerial and ground robot tasks. Our work...and ground robots in the presence of disturbances: We applied our methods to the problem of learning controllers for robots with novel disturbances in

The COGs (context, object, and goals) in multisensory processing.

PubMed

ten Oever, Sanne; Romei, Vincenzo; van Atteveldt, Nienke; Soto-Faraco, Salvador; Murray, Micah M; Matusz, Pawel J

2016-05-01

Our understanding of how perception operates in real-world environments has been substantially advanced by studying both multisensory processes and "top-down" control processes influencing sensory processing via activity from higher-order brain areas, such as attention, memory, and expectations. As the two topics have been traditionally studied separately, the mechanisms orchestrating real-world multisensory processing remain unclear. Past work has revealed that the observer's goals gate the influence of many multisensory processes on brain and behavioural responses, whereas some other multisensory processes might occur independently of these goals. Consequently, other forms of top-down control beyond goal dependence are necessary to explain the full range of multisensory effects currently reported at the brain and the cognitive level. These forms of control include sensitivity to stimulus context as well as the detection of matches (or lack thereof) between a multisensory stimulus and categorical attributes of naturalistic objects (e.g. tools, animals). In this review we discuss and integrate the existing findings that demonstrate the importance of such goal-, object- and context-based top-down control over multisensory processing. We then put forward a few principles emerging from this literature review with respect to the mechanisms underlying multisensory processing and discuss their possible broader implications.

Distributed computing testbed for a remote experimental environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butner, D.N.; Casper, T.A.; Howard, B.C.

1995-09-18

Collaboration is increasing as physics research becomes concentrated on a few large, expensive facilities, particularly in magnetic fusion energy research, with national and international participation. These facilities are designed for steady state operation and interactive, real-time experimentation. We are developing tools to provide for the establishment of geographically distant centers for interactive operations; such centers would allow scientists to participate in experiments from their home institutions. A testbed is being developed for a Remote Experimental Environment (REE), a ``Collaboratory.`` The testbed will be used to evaluate the ability of a remotely located group of scientists to conduct research on themore » DIII-D Tokamak at General Atomics. The REE will serve as a testing environment for advanced control and collaboration concepts applicable to future experiments. Process-to-process communications over high speed wide area networks provide real-time synchronization and exchange of data among multiple computer networks, while the ability to conduct research is enhanced by adding audio/video communication capabilities. The Open Software Foundation`s Distributed Computing Environment is being used to test concepts in distributed control, security, naming, remote procedure calls and distributed file access using the Distributed File Services. We are exploring the technology and sociology of remotely participating in the operation of a large scale experimental facility.« less

Creating a peaceful school learning environment: a controlled study of an elementary school intervention to reduce violence.

PubMed

Twemlow, S W; Fonagy, P; Sacco, F C; Gies, M L; Evans, R; Ewbank, R

2001-05-01

The impact of a manual-based antiviolence program on the learning climate in an elementary school over 4 years was compared with the outcome in a control school. The two schools were matched for demographic characteristics. The intervention in the experimental school was based on zero tolerance for bullying; the control school received only regular psychiatric consultation. Disciplinary and academic achievement data were collected in both schools. The experimental school showed significant reductions in discipline referrals and increases in scores on standardized academic achievement measures. A low-cost antiviolence intervention that does not focus on individual pathology or interfere with the educational process may improve the learning environment in elementary schools.

An agent-vector-host-environment model for controlling small arms and light weapons.

PubMed

Pinto, Andrew D; Sharma, Malika; Muggah, Robert

2011-05-01

Armed violence is a significant public health problem. It results in fatal and non-fatal injuries and disrupts social and economic processes that are essential to the health of individuals and communities. We argue that an agent-vector-host-environment model can be helpful in understanding and describing the availability and misuse of small arms and light weapons. Moreover, such a model can assist in identifying potential control points and in developing mitigation strategies. These concepts have been developed from analogous vector control programs and are applied to controlling arms to reduce their misuse. So-called 'denormalization' and 'de-legitimization' campaigns that focus on the vector - including the industry producing these commodities - can be based on the experience of public health in controlling tobacco use and exposure. This model can assist health professionals, civil society and governments in developing comprehensive strategies to limit the production, distribution and misuse of small arms and light weapons.

Media Ion Composition Controls Regulatory and Virulence Response of Salmonella in Spaceflight

PubMed Central

Wilson, James W.; Ott, C. Mark; Quick, Laura; Davis, Richard; zu Bentrup, Kerstin Höner; Crabbé, Aurélie; Richter, Emily; Sarker, Shameema; Barrila, Jennifer; Porwollik, Steffen; Cheng, Pui; McClelland, Michael; Tsaprailis, George; Radabaugh, Timothy; Hunt, Andrea; Shah, Miti; Nelman-Gonzalez, Mayra; Hing, Steve; Parra, Macarena; Dumars, Paula; Norwood, Kelly; Bober, Ramona; Devich, Jennifer; Ruggles, Ashleigh; CdeBaca, Autumn; Narayan, Satro; Benjamin, Joseph; Goulart, Carla; Rupert, Mark; Catella, Luke; Schurr, Michael J.; Buchanan, Kent; Morici, Lisa; McCracken, James; Porter, Marc D.; Pierson, Duane L.; Smith, Scott M.; Mergeay, Max; Leys, Natalie; Stefanyshyn-Piper, Heidemarie M.; Gorie, Dominic; Nickerson, Cheryl A.

2008-01-01

The spaceflight environment is relevant to conditions encountered by pathogens during the course of infection and induces novel changes in microbial pathogenesis not observed using conventional methods. It is unclear how microbial cells sense spaceflight-associated changes to their growth environment and orchestrate corresponding changes in molecular and physiological phenotypes relevant to the infection process. Here we report that spaceflight-induced increases in Salmonella virulence are regulated by media ion composition, and that phosphate ion is sufficient to alter related pathogenesis responses in a spaceflight analogue model. Using whole genome microarray and proteomic analyses from two independent Space Shuttle missions, we identified evolutionarily conserved molecular pathways in Salmonella that respond to spaceflight under all media compositions tested. Identification of conserved regulatory paradigms opens new avenues to control microbial responses during the infection process and holds promise to provide an improved understanding of human health and disease on Earth. PMID:19079590

Fused silica reflecting heat shields for outer planet entry probes

NASA Technical Reports Server (NTRS)

Congdon, W. M.; Peterson, D. L.

1975-01-01

The development of slip-cast fused silica is discussed as a heat shield designed to meet the needs of outer-planet entry probes. The distinguishing feature of silica is its ability to reflect the radiation imposed by planetary-entry environments. This reflectivity is particularly sensitive to degradation by the presence of trace amounts of contaminants introduced by the starting materials or by processing. The microstructure of a silica configuration also significantly influences the reflectivity and other thermomechanical properties. The processing techniques attendant on controlling microstructure while maintaining purity are discussed. The selection of a starting material of essential purity precludes the use of purified natural quartz and requires the use of synthetic fused silica. The silica is characterized in a limited combined heating test environment. The surface mass loss is controlled by liquid runoff from a relatively low-temperature melt layer; the reflectance is basically maintained and the material achieves a surprisingly high heat of ablation.

Traveling Magnetic Field Applications for Materials Processing in Space

NASA Technical Reports Server (NTRS)

Motakef, S.; Grugel, R. N.; Mazuruk, K.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

Including the capability to induce a controlled fluid flow in the melt can significantly enrich research on solidification phenomena in a microgravity environment. The traveling magnetic field (TMF) is a promising technique to achieve this goal and is the aim of our ground-based project. In this presentation we will discuss new theoretical as well as experimental results recently obtained by our group. In particular, we experimentally demonstrated efficient mixing of metal alloys in long tubes subjected to TMF during processing. Application of this technique can be an elegant solution to ensure melt homogenization prior to solidification in a microgravity environment where natural convection is generally absent. Results of our theoretical work on TMF induced flows, such as convection control in Bridgman as well as in the Traveling Heater method, will be presented. Possible applications of TMF on board the ISS will also be discussed.

Emergence of polysaccharide membrane walls through macro-space partitioning via interfacial instability.

PubMed

Okeyoshi, Kosuke; Okajima, Maiko K; Kaneko, Tatsuo

2017-07-21

Living organisms in drying environments build anisotropic structures and exhibit directionality through self-organization of biopolymers. However, the process of macro-scale assembly is still unknown. Here, we introduce a dissipative structure through a non-equilibrium process between hydration and deposition in the drying of a polysaccharide liquid crystalline solution. By controlling the geometries of the evaporation front in a limited space, multiple nuclei emerge to grow vertical membrane walls with macroscopic orientation. Notably, the membranes are formed through rational orientation of rod-like microassemblies along the dynamic three-phase contact line. Additionally, in the non-equilibrium state, a dissipative structure is ultimately immobilized as a macroscopically partitioned space by multiple vertical membranes. We foresee that such oriented membranes will be applicable to soft biomaterials with direction controllability, and the macroscopic space partitionings will aid in the understanding of the space recognition ability of natural products under drying environments.

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, Japanese astronaut Koichi Wakata looks over the Pressurized Module, or PM, part of the Japanese Experiment Module (JEM). The PM provides a shirt-sleeve environment in which astronauts on the International Space Station can conduct microgravity experiments. There are a total of 23 racks, including 10 experiment racks, inside the PM providing a power supply, communications, air conditioning, hardware cooling, water control and experiment support functions.

NASA Image and Video Library

2003-09-24

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, Japanese astronaut Koichi Wakata looks over the Pressurized Module, or PM, part of the Japanese Experiment Module (JEM). The PM provides a shirt-sleeve environment in which astronauts on the International Space Station can conduct microgravity experiments. There are a total of 23 racks, including 10 experiment racks, inside the PM providing a power supply, communications, air conditioning, hardware cooling, water control and experiment support functions.

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, technicians on the floor watch as a tray is extended from inside the Pressurized Module, or PM, part of the Japanese Experiment Module (JEM). The PM provides a shirt-sleeve environment in which astronauts on the International Space Station can conduct microgravity experiments. There are a total of 23 racks, including 10 experiment racks, inside the PM providing a power supply, communications, air conditioning, hardware cooling, water control and experiment support functions.

NASA Image and Video Library

2003-09-24

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, technicians on the floor watch as a tray is extended from inside the Pressurized Module, or PM, part of the Japanese Experiment Module (JEM). The PM provides a shirt-sleeve environment in which astronauts on the International Space Station can conduct microgravity experiments. There are a total of 23 racks, including 10 experiment racks, inside the PM providing a power supply, communications, air conditioning, hardware cooling, water control and experiment support functions.

General purpose rocket furnace

NASA Technical Reports Server (NTRS)

Aldrich, B. R.; Whitt, W. D. (Inventor)

1979-01-01

A multipurpose furnace for space vehicles used for material processing experiments in an outer space environment is described. The furnace contains three separate cavities designed to process samples of the widest possible range of materials and thermal requirements. Each cavity contains three heating elements capable of independent function under the direction of an automatic and programmable control system. A heat removable mechanism is also provided for each cavity which operates in conjunction with the control system for establishing an isothermally heated cavity or a wide range of thermal gradients and cool down rates. A monitoring system compatible with the rocket telemetry provides furnace performance and sample growth rate data throughout the processing cycle.

Final Report: Mechanisms of sputter ripple formation: coupling among energetic ions, surface kinetics, stress and composition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chason, Eric; Shenoy, Vivek

Self-organized pattern formation enables the creation of nanoscale surface structures over large areas based on fundamental physical processes rather than an applied template. Low energy ion bombardment is one such method that induces the spontaneous formation of a wide variety of interesting morphological features (e.g., sputter ripples and/or quantum dots). This program focused on the processes controlling sputter ripple formation and the kinetics controlling the evolution of surfaces and nanostructures in high flux environments. This was done by using systematic, quantitative experiments to measure ripple formation under a variety of processing conditions coupled with modeling to interpret the results.

When locomotion is used to interact with the environment: investigation of the link between emotions and the twofold goal-directed locomotion in humans.

PubMed

Vernazza-Martin, S; Longuet, S; Damry, T; Chamot, J M; Dru, V

2015-10-01

Walking as a means to interact with the environment has a twofold goal: body displacement (intermediate goal) and the future action on the environment (final representational goal). This involves different processes that plan, program, and control goal-directed locomotion linked to motivation as an "emotional state," which leads to achieving this twofold goal. The aim of the present study was to determine whether emotional valence associated with the final representational goal influences these processes or whether they depend more on the emotional valence associated with the intermediate goal in young adults. Twenty subjects, aged 18-35 years, were instructed to erase an emotional picture that appeared on a wall as soon as they saw it. They had to press a stop button located 5 m in front of them with their right hand. Their gait was analyzed using a force platform and the Vicon system. The main results suggest that the emotional valence of the intermediate goal has the greatest effect on the processes that organize and modulate goal-directed locomotion. A positive valence facilitates cognitive processes involved in the temporal organization of locomotion. A negative valence disturbs the cognitive processes involved in the spatial organization of the locomotion and online motor control, leading to a deviating trajectory and a final body position that is more distant from the stop button. These results are discussed in line with the motivational direction hypothesis and with the affective meaning of the intended response goal.

Design And Implementation Of PID Controller Using Relay Feedback On TRMS (Twin Rotor MIMO System)

NASA Astrophysics Data System (ADS)

Shah, Dipesh H.

2011-12-01

Today, many process control problems can be adequately and routinely solved by conventional PID control strategies. The overriding reason that the PID controller is so widely accepted is its simple structure which has proved to be very robust with regard to many commonly met process control problems as for instance disturbances and nonlinearities. Relay feedback methods have been widely used in tuning proportional-integral-derivative controllers due to its closed loop nature. In this work, Relay based PID controller is designed and successfully implemented on TRMS (Twin Rotor MIMO System) in SISO and MIMO configurations. The performance of a Relay based PID controller for control of TRMS is investigated and performed satisfactorily. The system shares some features with a helicopter, such as important interactions between the vertical and horizontal motions. The RTWT toolbox in the MATLAB environment is used to perform real-time experiments.

The Substitution of IVD (Ion Vapor Deposition) Aluminum for Cadmium

DTIC Science & Technology

1989-08-01

environment, it can finu its A in( the water suHpl o- fooo chain. Also, with electroplated cadmium processing, tnere are auditional nazaros associated win...no , - r e CUr r in ( polut io n- r elIt e costs. Tne po IIut ion controlI costs for all caG;iul n processing , nclIUd ino, clpitl treatm’ient , col...H T P, H VacuumCadmium None T. O. H T. P. H Key T - Toxic materials 0 - OSHA standards imposed P - Polution control required H - Hazardous waste

Welding torch trajectory generation for hull joining using autonomous welding mobile robot

NASA Astrophysics Data System (ADS)

Hascoet, J. Y.; Hamilton, K.; Carabin, G.; Rauch, M.; Alonso, M.; Ares, E.

2012-04-01

Shipbuilding processes involve highly dangerous manual welding operations. Welding of ship hulls presents a hazardous environment for workers. This paper describes a new robotic system, developed by the SHIPWELD consortium, that moves autonomously on the hull and automatically executes the required welding processes. Specific focus is placed on the trajectory control of such a system and forms the basis for the discussion in this paper. It includes a description of the robotic hardware design as well as some methodology used to establish the torch trajectory control.

Industry Speed Bumps on Local Tobacco Control in Japan? The Case of Hyogo

PubMed Central

Yamada, Keiko; Mori, Nagisa; Kashiwabara, Mina; Yasuda, Sakiko; Horie, Rumi; Yamato, Hiroshi; Garçon, Loic; Armada, Francisco

2015-01-01

Background Despite being a signatory since 2004, Japan has not yet fully implemented Article 8 of the World Health Organization’s Framework Convention on Tobacco Control regarding 100% protection against exposure to second-hand smoke (SHS). The Japanese government still recognizes designated smoking rooms (DSRs) in public space as a valid control measure. Furthermore, subnational initiatives for tobacco control in Japan are of limited effectiveness. Through an analysis of the Hyogo initiative in 2012, we identified key barriers to the achievement of a smoke-free environment. Methods Using a descriptive case-study approach, we analyzed the smoke-free policy development process. The information was obtained from meeting minutes and other gray literature, such as public records, well as key informant interviews. Results Hyogo Prefecture established a committee to propose measures against SHS, and most committee members agreed with establishing completely smoke-free environments. However, the hospitality sector representatives opposed regulation, and tobacco companies were allowed to make a presentation to the committee. Further, political power shifted against completely smoke-free environments in the context of upcoming local elections, which was an obvious barrier to effective regulation. Throughout the approving process, advocacy by civil society for stronger regulation was weak. Eventually, the ordinance approved by the Prefectural Assembly was even weaker than the committee proposal and included wide exemptions. Conclusions The analysis of Hyogo’s SHS control initiative shed light on three factors that present challenges to implementing tobacco control regulations in Japan, from which other countries can also draw lessons: incomplete national legislation, the weakness of advocacy by the civil society, and the interference of the tobacco industry. PMID:26155758

Development of Process Analytical Technology (PAT) methods for controlled release pellet coating.

PubMed

Avalle, P; Pollitt, M J; Bradley, K; Cooper, B; Pearce, G; Djemai, A; Fitzpatrick, S

2014-07-01

This work focused on the control of the manufacturing process for a controlled release (CR) pellet product, within a Quality by Design (QbD) framework. The manufacturing process was Wurster coating: firstly layering active pharmaceutical ingredient (API) onto sugar pellet cores and secondly a controlled release (CR) coating. For each of these two steps, development of a Process Analytical Technology (PAT) method is discussed and also a novel application of automated microscopy as the reference method. Ultimately, PAT methods should link to product performance and the two key Critical Quality Attributes (CQAs) for this CR product are assay and release rate, linked to the API and CR coating steps respectively. In this work, the link between near infra-red (NIR) spectra and those attributes was explored by chemometrics over the course of the coating process in a pilot scale industrial environment. Correlations were built between the NIR spectra and coating weight (for API amount), CR coating thickness and dissolution performance. These correlations allow the coating process to be monitored at-line and so better control of the product performance in line with QbD requirements. Copyright © 2014 Elsevier B.V. All rights reserved.

Monitoring hygiene on- and at-line is critical for controlling Listeria monocytogenes during produce processing.

PubMed

Pappelbaum, Krystyna; Grif, Katharina; Heller, Ingrid; Wüirzner, Reinhard; Hein, Ingeborg; Ellerbroek, Lueppo; Wagner, Martin

2008-04-01

The prevalence of Listeria monocytogenes in different types of produce and on processing plant environments was investigated over a 4-year period in a large produce processing plant in Poland. Prevalence of L. monocytogenes was 46% in frozen vegetables and 41.3% in swab samples taken from the plant environment. Survival studies using artificial inocula demonstrated that the number of Listeria in frozen produce stored for 100 days did not significantly decrease in relation to the initial contamination level. A subset of 129 L. monocytogenes isolates originating from produce and the plant environment were typed by pulsed-field gel electrophoresis. Seventy-six of these isolates were retyped by ribo- and serotyping. Thirteen pulsotypes and 18 ribotypes were distinguished. Persistent Listeria isolates were found even when cleansing and sanitization was applied on a daily basis. Nine (69.2%) of 13 pulsotypes were recovered during a period of more than 2 years. L. monocytogenes of the same pulsotype was isolated from broccoli sampled directly before and after blanching, thus suggesting that blanching at 92 to 95 degrees C for 4 to 8 min did not result in a Listeria-free product, most likely due to massive recontamination. This finding is of importance since blanching is the only critical control point in produce processing. Cross-contamination between the two lines was demonstrated through isolating L. monocytogenes strains indistinguishable by pulsed-field gel electrophoresis from contaminated gloves and floor surfaces.

A review of factors influencing the availability of dissolved oxygen to incubating salmonid embryos

NASA Astrophysics Data System (ADS)

Greig, S. M.; Sear, D. A.; Carling, P. A.

2007-01-01

Previous investigations into factors influencing incubation success of salmonid progeny have largely been limited to the development of empirical relationships between characteristics of the incubation environment and survival to emergence. It is suggested that adopting a process-based approach to assessing incubation success aids identification of the precise causes of embryonic mortalities, and provides a robust framework for developing and implementing managerial responses.Identifying oxygen availability within the incubation environment as a limiting factor, a comprehensive review of trends in embryonic respiration, and processes influencing the flux of oxygenated water through gravel riverbeds is provided. The availability of oxygen to incubating salmonid embryos is dependent on the exchange of oxygenated water with the riverbed, and the ability of the riverbed gravel medium to transport this water at a rate and concentration appropriate to support embryonic respiratory requirements. Embryonic respiratory trends indicate that oxygen consumption varies with stage of development, ambient water temperature and oxygen availability. The flux of oxygenated water through the incubation environment is controlled by a complex interaction of intragravel and extragravel processes and factors. The processes driving the exchange of channel water with gravel riverbeds include bed topography, bed permeability, and surface roughness effects. The flux of oxygenated water through riverbed gravels is controlled by gravel permeability, coupling of surface-subsurface flow and oxygen demands imposed by materials infiltrating riverbed gravels. Temporally and spatially variable inputs of groundwater can also influence the oxygen concentration of interstitial water. Copyright

Classification of Movement and Inhibition Using a Hybrid BCI.

PubMed

Chmura, Jennifer; Rosing, Joshua; Collazos, Steven; Goodwin, Shikha J

2017-01-01

Brain-computer interfaces (BCIs) are an emerging technology that are capable of turning brain electrical activity into commands for an external device. Motor imagery (MI)-when a person imagines a motion without executing it-is widely employed in BCI devices for motor control because of the endogenous origin of its neural control mechanisms, and the similarity in brain activation to actual movements. Challenges with translating a MI-BCI into a practical device used outside laboratories include the extensive training required, often due to poor user engagement and visual feedback response delays; poor user flexibility/freedom to time the execution/inhibition of their movements, and to control the movement type (right arm vs. left leg) and characteristics (reaching vs. grabbing); and high false positive rates of motion control. Solutions to improve sensorimotor activation and user performance of MI-BCIs have been explored. Virtual reality (VR) motor-execution tasks have replaced simpler visual feedback (smiling faces, arrows) and have solved this problem to an extent. Hybrid BCIs (hBCIs) implementing an additional control signal to MI have improved user control capabilities to a limited extent. These hBCIs either fail to allow the patients to gain asynchronous control of their movements, or have a high false positive rate. We propose an immersive VR environment which provides visual feedback that is both engaging and immediate, but also uniquely engages a different cognitive process in the patient that generates event-related potentials (ERPs). These ERPs provide a key executive function for the users to execute/inhibit movements. Additionally, we propose signal processing strategies and machine learning algorithms to move BCIs toward developing long-term signal stability in patients with distinctive brain signals and capabilities to control motor signals. The hBCI itself and the VR environment we propose would help to move BCI technology outside laboratory environments for motor rehabilitation in hospitals, and potentially for controlling a prosthetic.

Classification of Movement and Inhibition Using a Hybrid BCI

PubMed Central

Chmura, Jennifer; Rosing, Joshua; Collazos, Steven; Goodwin, Shikha J.

2017-01-01

Brain-computer interfaces (BCIs) are an emerging technology that are capable of turning brain electrical activity into commands for an external device. Motor imagery (MI)—when a person imagines a motion without executing it—is widely employed in BCI devices for motor control because of the endogenous origin of its neural control mechanisms, and the similarity in brain activation to actual movements. Challenges with translating a MI-BCI into a practical device used outside laboratories include the extensive training required, often due to poor user engagement and visual feedback response delays; poor user flexibility/freedom to time the execution/inhibition of their movements, and to control the movement type (right arm vs. left leg) and characteristics (reaching vs. grabbing); and high false positive rates of motion control. Solutions to improve sensorimotor activation and user performance of MI-BCIs have been explored. Virtual reality (VR) motor-execution tasks have replaced simpler visual feedback (smiling faces, arrows) and have solved this problem to an extent. Hybrid BCIs (hBCIs) implementing an additional control signal to MI have improved user control capabilities to a limited extent. These hBCIs either fail to allow the patients to gain asynchronous control of their movements, or have a high false positive rate. We propose an immersive VR environment which provides visual feedback that is both engaging and immediate, but also uniquely engages a different cognitive process in the patient that generates event-related potentials (ERPs). These ERPs provide a key executive function for the users to execute/inhibit movements. Additionally, we propose signal processing strategies and machine learning algorithms to move BCIs toward developing long-term signal stability in patients with distinctive brain signals and capabilities to control motor signals. The hBCI itself and the VR environment we propose would help to move BCI technology outside laboratory environments for motor rehabilitation in hospitals, and potentially for controlling a prosthetic. PMID:28860986

Investigation of high voltage spacecraft system interactions with plasma environments

NASA Technical Reports Server (NTRS)

Stevens, N. J.; Berkopec, F. D.; Purvis, C. K.; Grier, N.; Staskus, J. V.

1978-01-01

An experimental investigation was undertaken for insulator and conductor test surfaces biased up to + or - 1kV in a simulated low earth orbit charged particle environment. It was found that these interactions are controlled by the insulator surfaces surrounding the biased conductors. For positive applied voltages the electron current collection can be enhanced by the insulators. For negative applied voltages the insulator surface confines the voltage to the conductor region. Understanding these interactions and the technology to control their impact on system operation is essential to the design of solar cell arrays for ion drive propulsion applications that use direct drive power processing.

The materials processing research base of the Materials Processing Center

NASA Technical Reports Server (NTRS)

Latanision, R. M.

1986-01-01

An annual report of the research activities of the Materials Processing Center of the Massachusetts Institute of Technology is given. Research on dielectrophoresis in the microgravity environment, phase separation kinetics in immiscible liquids, transport properties of droplet clusters in gravity-free fields, probes and monitors for the study of solidification of molten semiconductors, fluid mechanics and mass transfer in melt crystal growth, and heat flow control and segregation in directional solidification are discussed.

Hierarchical Process Composition: Dynamic Maintenance of Structure in a Distributed Environment

DTIC Science & Technology

1988-01-01

One prominent hne of research stresses the independence of address space and thread of control, and the resulting efficiencies due to shared memory...cooperating processes. StarOS focuses on case of use and a general capability mechanism, while Medusa stresses the effect of distributed hardware on system...process structure and the asynchrony among agents and between agents and sources of failure. By stressing dynamic structure, we are led to adopt an

How Do I Sample the Environment and Equipment?

NASA Astrophysics Data System (ADS)

Kornacki, Jeffrey L.

Food product contamination from the post-processing environment is likely the most frequent cause of contaminated processed food product recalls and a significant source of poisoning outbreaks, and shelf life problems in North America with processed Ready-To-Eat foods. Conditions exist for the growth of microorganisms in most food processing factories. Failure to clean and effectively sanitize a microbial growth niche can lead to biofilm formation. Biofilms may be orders of magnitude more resistant to destruction by sanitizers. Cells in some biofilms have been shown to be 1,000 times more resistant to destruction than those which are freely suspended. This has implications for cleaning, sanitizing, sampling, and training. Sampling the factory environment is one means of monitoring the efficacy of microbiological control as well as a powerful tool for in-factory contamination investigation. Many sampling techniques exist and are discussed. It is important to recognize the difference between cleaning (removal of soil) and sanitization (reduction of microbial populations). Knowing where, when, and how to sample, how many samples to take, and what to test for and how to interpret test information is critical in finding and preventing contamination.

A fuzzy classifier system for process control

NASA Technical Reports Server (NTRS)

Karr, C. L.; Phillips, J. C.

1994-01-01

A fuzzy classifier system that discovers rules for controlling a mathematical model of a pH titration system was developed by researchers at the U.S. Bureau of Mines (USBM). Fuzzy classifier systems successfully combine the strengths of learning classifier systems and fuzzy logic controllers. Learning classifier systems resemble familiar production rule-based systems, but they represent their IF-THEN rules by strings of characters rather than in the traditional linguistic terms. Fuzzy logic is a tool that allows for the incorporation of abstract concepts into rule based-systems, thereby allowing the rules to resemble the familiar 'rules-of-thumb' commonly used by humans when solving difficult process control and reasoning problems. Like learning classifier systems, fuzzy classifier systems employ a genetic algorithm to explore and sample new rules for manipulating the problem environment. Like fuzzy logic controllers, fuzzy classifier systems encapsulate knowledge in the form of production rules. The results presented in this paper demonstrate the ability of fuzzy classifier systems to generate a fuzzy logic-based process control system.

Using Automation to Improve the Flight Software Testing Process

NASA Technical Reports Server (NTRS)

ODonnell, James R., Jr.; Morgenstern, Wendy M.; Bartholomew, Maureen O.

2001-01-01

One of the critical phases in the development of a spacecraft attitude control system (ACS) is the testing of its flight software. The testing (and test verification) of ACS flight software requires a mix of skills involving software, knowledge of attitude control, and attitude control hardware, data manipulation, and analysis. The process of analyzing and verifying flight software test results often creates a bottleneck which dictates the speed at which flight software verification can be conducted. In the development of the Microwave Anisotropy Probe (MAP) spacecraft ACS subsystem, an integrated design environment was used that included a MAP high fidelity (HiFi) simulation, a central database of spacecraft parameters, a script language for numeric and string processing, and plotting capability. In this integrated environment, it was possible to automate many of the steps involved in flight software testing, making the entire process more efficient and thorough than on previous missions. In this paper, we will compare the testing process used on MAP to that used on other missions. The software tools that were developed to automate testing and test verification will be discussed, including the ability to import and process test data, synchronize test data and automatically generate HiFi script files used for test verification, and an automated capability for generating comparison plots. A summary of the benefits of applying these test methods on MAP will be given. Finally, the paper will conclude with a discussion of re-use of the tools and techniques presented, and the ongoing effort to apply them to flight software testing of the Triana spacecraft ACS subsystem.

Comparing Problem-Based Learning Students to Students in a Lecture-Based Curriculum: Learning Strategies and the Relation with Self-Study Time

ERIC Educational Resources Information Center

Wijnen, Marit; Loyens, Sofie M. M.; Smeets, Guus; Kroeze, Maarten; van der Molen, Henk

2017-01-01

In educational theory, deep processing (i.e., connecting different study topics together) and self-regulation (i.e., taking control over one's own learning process) are considered effective learning strategies. These learning strategies can be influenced by the learning environment. Problem-based learning (PBL), a student-centered educational…

Patterns of Control over the Teaching-Studying-Learning Process and Classrooms as Complex Dynamic Environments: A Theoretical Framework

ERIC Educational Resources Information Center

Harjunen, Elina

2012-01-01

In this theoretical paper the role of power in classroom interactions is examined in terms of a dominance continuum to advance a theoretical framework justifying the emergence of three ways of distributing power when it comes to dealing with the control over the teaching-studying-learning (TSL) "pattern of teacher domination," "pattern of…

40 CFR 60.4861 - How do I establish an affirmative defense for exceedance of an emission limit or standard during...

Code of Federal Regulations, 2011 CFR

2011-07-01

..., and unavoidable failure of air pollution control and monitoring equipment, process equipment, or a... activity or event that could have been foreseen and avoided, or planned for, and (iv) Were not part of a... ambient air quality, the environment and human health, and (6) All emissions monitoring and control...

40 CFR 60.4861 - How do I establish an affirmative defense for exceedance of an emission limit or standard during...

Code of Federal Regulations, 2012 CFR

2012-07-01

..., and unavoidable failure of air pollution control and monitoring equipment, process equipment, or a... activity or event that could have been foreseen and avoided, or planned for, and (iv) Were not part of a... ambient air quality, the environment and human health, and (6) All emissions monitoring and control...

Using a virtual world for robot planning

NASA Astrophysics Data System (ADS)

Benjamin, D. Paul; Monaco, John V.; Lin, Yixia; Funk, Christopher; Lyons, Damian

2012-06-01

We are building a robot cognitive architecture that constructs a real-time virtual copy of itself and its environment, including people, and uses the model to process perceptual information and to plan its movements. This paper describes the structure of this architecture. The software components of this architecture include PhysX for the virtual world, OpenCV and the Point Cloud Library for visual processing, and the Soar cognitive architecture that controls the perceptual processing and task planning. The RS (Robot Schemas) language is implemented in Soar, providing the ability to reason about concurrency and time. This Soar/RS component controls visual processing, deciding which objects and dynamics to render into PhysX, and the degree of detail required for the task. As the robot runs, its virtual model diverges from physical reality, and errors grow. The Match-Mediated Difference component monitors these errors by comparing the visual data with corresponding data from virtual cameras, and notifies Soar/RS of significant differences, e.g. a new object that appears, or an object that changes direction unexpectedly. Soar/RS can then run PhysX much faster than real-time and search among possible future world paths to plan the robot's actions. We report experimental results in indoor environments.

Control of a Quadcopter Aerial Robot Using Optic Flow Sensing

NASA Astrophysics Data System (ADS)

Hurd, Michael Brandon

This thesis focuses on the motion control of a custom-built quadcopter aerial robot using optic flow sensing. Optic flow sensing is a vision-based approach that can provide a robot the ability to fly in global positioning system (GPS) denied environments, such as indoor environments. In this work, optic flow sensors are used to stabilize the motion of quadcopter robot, where an optic flow algorithm is applied to provide odometry measurements to the quadcopter's central processing unit to monitor the flight heading. The optic-flow sensor and algorithm are capable of gathering and processing the images at 250 frames/sec, and the sensor package weighs 2.5 g and has a footprint of 6 cm2 in area. The odometry value from the optic flow sensor is then used a feedback information in a simple proportional-integral-derivative (PID) controller on the quadcopter. Experimental results are presented to demonstrate the effectiveness of using optic flow for controlling the motion of the quadcopter aerial robot. The technique presented herein can be applied to different types of aerial robotic systems or unmanned aerial vehicles (UAVs), as well as unmanned ground vehicles (UGV).

Selection of a Data Acquisition and Controls System Communications and Software Architecture for Johnson Space Center's Space Environment Simulation Laboratory Thermal and Vacuum Test Facilities

NASA Technical Reports Server (NTRS)

Jordan, Eric A.

2004-01-01

Upgrade of data acquisition and controls systems software at Johnson Space Center's Space Environment Simulation Laboratory (SESL) involved the definition, evaluation and selection of a system communication architecture and software components. A brief discussion of the background of the SESL and its data acquisition and controls systems provides a context for discussion of the requirements for each selection. Further framework is provided as upgrades to these systems accomplished in the 1990s and in 2003 are compared to demonstrate the role that technological advances have had in their improvement. Both of the selections were similar in their three phases; 1) definition of requirements, 2) identification of candidate products and their evaluation and testing and 3) selection by comparison of requirement fulfillment. The candidates for the communication architecture selection embraced several different methodologies which are explained and contrasted. Requirements for this selection are presented and the selection process is described. Several candidates for the software component of the data acquisition and controls system are identified, requirements for evaluation and selection are presented, and the evaluation process is described.

2011 Quantum Control of Light & Matter Gordon Research Conference (July 31-August 5, 2011, Mount Holyoke College, South Hadley, MA)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas Weinacht

2011-08-05

Quantum control of light and matter is the quest to steer a physical process to a desirable outcome, employing constructive and destructive interference. Three basic questions address feasibility of quantum control: (1) The problem of controllability, does a control field exist for a preset initial and target state; (2) Synthesis, constructively finding the field that leads to the target; and (3) Optimal Control Theory - optimizing the field that carries out this task. These continue to be the fundamental theoretical questions to be addressed in the conference. How to realize control fields in the laboratory is an ongoing challenge. Thismore » task is very diverse viewing the emergence of control scenarios ranging from attoseconds to microseconds. How do the experimental observations reflect on the theoretical framework? The typical arena of quantum control is an open environment where much of the control is indirect. How are control scenarios realized in dissipative open systems? Can new control opportunities emerge? Can one null decoherence effects? An ideal setting for control is ultracold matter. The initial and final state can be defined more precisely. Coherent control unifies many fields of physical science. A lesson learned in one field can reflect on another. Currently quantum information processing has emerged as a primary target of control where the key issue is controlling quantum gate operation. Modern nonlinear spectroscopy has emerged as another primary field. The challenge is to unravel the dynamics of molecular systems undergoing strong interactions with the environment. Quantum optics where non-classical fields are to be generated and employed. Finally, coherent control is the basis for quantum engineering. These issues will be under the limelight of the Gordon conference on Quantum Control of Light and Matter.« less

CHANGING CLIMATE AND PHOTOBIOGEOCHEMICAL CYCLES IN AQUATIC ENVIRONMENTS

EPA Science Inventory

Global biogeochemistry plays a critical role in controlling life processes, climate and their interactions, including effects on atmospheric greenhouse gas concentrations. Recent evidence indicates that the light-driven part of aquatic biogeochemical cycles is being altered by in...

40 CFR 763.179 - Confidential business information claims.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Prohibition of the Manufacture, Importation, Processing, and Distribution in Commerce of Certain Asbestos-Containing Products; Labeling Requirements § 763.179 Confidential... asbestos on human health and the environment? If your answer is yes, explain. ...

40 CFR 721.6090 - Phosphoramide.

Code of Federal Regulations, 2010 CFR

2010-07-01

....6090 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT...) Hazard communication program. A significant new use of this substance is any manner or method of manufacture, import, or processing associated with any use of this substance without providing risk...

Replication in Mobile Environments

DTIC Science & Technology

2007-12-01

control number. 1. REPORT DATE 01 DEC 2007 2. REPORT TYPE N/A 3. DATES COVERED 4. TITLE AND SUBTITLE Data Replication Over Disadvantaged ...Communication, Information Processing, and Ergonomics KIE What is the Problem? Data replication among distributed databases occurring over disadvantaged

Confessions of a robot lobotomist

NASA Technical Reports Server (NTRS)

Gottshall, R. Marc

1994-01-01

Since its inception, numerically controlled (NC) machining methods have been used throughout the aerospace industry to mill, drill, and turn complex shapes by sequentially stepping through motion programs. However, the recent demand for more precision, faster feeds, exotic sensors, and branching execution have existing computer numerical control (CNC) and distributed numerical control (DNC) systems running at maximum controller capacity. Typical disadvantages of current CNC's include fixed memory capacities, limited communication ports, and the use of multiple control languages. The need to tailor CNC's to meet specific applications, whether it be expanded memory, additional communications, or integrated vision, often requires replacing the original controller supplied with the commercial machine tool with a more powerful and capable system. This paper briefly describes the process and equipment requirements for new controllers and their evolutionary implementation in an aerospace environment. The process of controller retrofit with currently available machines is examined, along with several case studies and their computational and architectural implications.

Countering Terrorism Through Control of Pakistan’s Information Environment

DTIC Science & Technology

2014-09-01

media caused the social mobilization or simply helped in the communication process.23 Information travelling over the Internet has a peculiarity...that at the individual level of the information environment for a typical Pakistani community , the Mullah is still a more effective tool to affect... literacy rate of the society, will have an exponential influence in the society. D. CONCLUSIONS 1. Information can be used to as a tool to influence

Mission Control Center (MCC) System Specification for the Shuttle Orbital Flight Test (OFT) Timeframe

NASA Technical Reports Server (NTRS)

1976-01-01

System specifications to be used by the mission control center (MCC) for the shuttle orbital flight test (OFT) time frame were described. The three support systems discussed are the communication interface system (CIS), the data computation complex (DCC), and the display and control system (DCS), all of which may interfere with, and share processing facilities with other applications processing supporting current MCC programs. The MCC shall provide centralized control of the space shuttle OFT from launch through orbital flight, entry, and landing until the Orbiter comes to a stop on the runway. This control shall include the functions of vehicle management in the area of hardware configuration (verification), flight planning, communication and instrumentation configuration management, trajectory, software and consumables, payloads management, flight safety, and verification of test conditions/environment.

Automation of testing modules of controller ELSY-ТМК

NASA Astrophysics Data System (ADS)

Dolotov, A. E.; Dolotova, R. G.; Petuhov, D. V.; Potapova, A. P.

2017-01-01

In modern life, there are means for automation of various processes which allow one to provide high quality standards of released products and to raise labour efficiency. In the given paper, the data on the automation of the test process of the ELSY-TMK controller [1] is presented. The ELSY-TMK programmed logic controller is an effective modular platform for construction of automation systems for small and average branches of industrial production. The modern and functional standard of communication and open environment of the logic controller give a powerful tool of wide spectrum applications for industrial automation. The algorithm allows one to test controller modules by operating the switching system and external devices faster and at a higher level of quality than a human without such means does.

NG6: Integrated next generation sequencing storage and processing environment.

PubMed

Mariette, Jérôme; Escudié, Frédéric; Allias, Nicolas; Salin, Gérald; Noirot, Céline; Thomas, Sylvain; Klopp, Christophe

2012-09-09

Next generation sequencing platforms are now well implanted in sequencing centres and some laboratories. Upcoming smaller scale machines such as the 454 junior from Roche or the MiSeq from Illumina will increase the number of laboratories hosting a sequencer. In such a context, it is important to provide these teams with an easily manageable environment to store and process the produced reads. We describe a user-friendly information system able to manage large sets of sequencing data. It includes, on one hand, a workflow environment already containing pipelines adapted to different input formats (sff, fasta, fastq and qseq), different sequencers (Roche 454, Illumina HiSeq) and various analyses (quality control, assembly, alignment, diversity studies,…) and, on the other hand, a secured web site giving access to the results. The connected user will be able to download raw and processed data and browse through the analysis result statistics. The provided workflows can easily be modified or extended and new ones can be added. Ergatis is used as a workflow building, running and monitoring system. The analyses can be run locally or in a cluster environment using Sun Grid Engine. NG6 is a complete information system designed to answer the needs of a sequencing platform. It provides a user-friendly interface to process, store and download high-throughput sequencing data.

Determining robot actions for tasks requiring sensor interaction

NASA Technical Reports Server (NTRS)

Budenske, John; Gini, Maria

1989-01-01

The performance of non-trivial tasks by a mobile robot has been a long term objective of robotic research. One of the major stumbling blocks to this goal is the conversion of the high-level planning goals and commands into the actuator and sensor processing controls. In order for a mobile robot to accomplish a non-trivial task, the task must be described in terms of primitive actions of the robot's actuators. Most non-trivial tasks require the robot to interact with its environment; thus necessitating coordination of sensor processing and actuator control to accomplish the task. The main contention is that the transformation from the high level description of the task to the primitive actions should be performed primarily at execution time, when knowledge about the environment can be obtained through sensors. It is proposed to produce the detailed plan of primitive actions by using a collection of low-level planning components that contain domain specific knowledge and knowledge about the available sensors, actuators, and sensor/actuator processing. This collection will perform signal and control processing as well as serve as a control interface between an actual mobile robot and a high-level planning system. Previous research has shown the usefulness of high-level planning systems to plan the coordination of activities such to achieve a goal, but none have been fully applied to actual mobile robots due to the complexity of interacting with sensors and actuators. This control interface is currently being implemented on a LABMATE mobile robot connected to a SUN workstation and will be developed such to enable the LABMATE to perform non-trivial, sensor-intensive tasks as specified by a planning system.

Implementation and benefits of advanced process control for lithography CD and overlay

NASA Astrophysics Data System (ADS)

Zavyalova, Lena; Fu, Chong-Cheng; Seligman, Gary S.; Tapp, Perry A.; Pol, Victor

2003-05-01

Due to the rapidly reduced imaging process windows and increasingly stingent device overlay requirements, sub-130 nm lithography processes are more severely impacted than ever by systamic fault. Limits on critical dimensions (CD) and overlay capability further challenge the operational effectiveness of a mix-and-match environment using multiple lithography tools, as such mode additionally consumes the available error budgets. Therefore, a focus on advanced process control (APC) methodologies is key to gaining control in the lithographic modules for critical device levels, which in turn translates to accelerated yield learning, achieving time-to-market lead, and ultimately a higher return on investment. This paper describes the implementation and unique challenges of a closed-loop CD and overlay control solution in high voume manufacturing of leading edge devices. A particular emphasis has been placed on developing a flexible APC application capable of managing a wide range of control aspects such as process and tool drifts, single and multiple lot excursions, referential overlay control, 'special lot' handling, advanced model hierarchy, and automatic model seeding. Specific integration cases, including the multiple-reticle complementary phase shift lithography process, are discussed. A continuous improvement in the overlay and CD Cpk performance as well as the rework rate has been observed through the implementation of this system, and the results are studied.

Proposed algorithm to improve job shop production scheduling using ant colony optimization method

NASA Astrophysics Data System (ADS)

Pakpahan, Eka KA; Kristina, Sonna; Setiawan, Ari

2017-12-01

This paper deals with the determination of job shop production schedule on an automatic environment. On this particular environment, machines and material handling system are integrated and controlled by a computer center where schedule were created and then used to dictate the movement of parts and the operations at each machine. This setting is usually designed to have an unmanned production process for a specified interval time. We consider here parts with various operations requirement. Each operation requires specific cutting tools. These parts are to be scheduled on machines each having identical capability, meaning that each machine is equipped with a similar set of cutting tools therefore is capable of processing any operation. The availability of a particular machine to process a particular operation is determined by the remaining life time of its cutting tools. We proposed an algorithm based on the ant colony optimization method and embedded them on matlab software to generate production schedule which minimize the total processing time of the parts (makespan). We test the algorithm on data provided by real industry and the process shows a very short computation time. This contributes a lot to the flexibility and timelines targeted on an automatic environment.

Remote Neural Pendants In A Welding-Control System

NASA Technical Reports Server (NTRS)

Venable, Richard A.; Bucher, Joseph H.

1995-01-01

Neural network integrated circuits enhance functionalities of both remote terminals (called "pendants") and communication links, without necessitating installation of additional wires in links. Makes possible to incorporate many features into pendant, including real-time display of critical welding parameters and other process information, capability for communication between technician at pendant and host computer or technician elsewhere in system, and switches and potentiometers through which technician at pendant exerts remote control over such critical aspects of welding process as current, voltage, rate of travel, flow of gas, starting, and stopping. Other potential manufacturing applications include control of spray coating and of curing of composite materials. Potential nonmanufacturing uses include remote control of heating, air conditioning, and lighting in electrically noisy and otherwise hostile environments.

Simulation model for plant growth in controlled environment systems

NASA Technical Reports Server (NTRS)

Raper, C. D., Jr.; Wann, M.

1986-01-01

The role of the mathematical model is to relate the individual processes to environmental conditions and the behavior of the whole plant. Using the controlled-environment facilities of the phytotron at North Carolina State University for experimentation at the whole-plant level and methods for handling complex models, researchers developed a plant growth model to describe the relationships between hierarchial levels of the crop production system. The fundamental processes that are considered are: (1) interception of photosynthetically active radiation by leaves, (2) absorption of photosynthetically active radiation, (3) photosynthetic transformation of absorbed radiation into chemical energy of carbon bonding in solube carbohydrates in the leaves, (4) translocation between carbohydrate pools in leaves, stems, and roots, (5) flow of energy from carbohydrate pools for respiration, (6) flow from carbohydrate pools for growth, and (7) aging of tissues. These processes are described at the level of organ structure and of elementary function processes. The driving variables of incident photosynthetically active radiation and ambient temperature as inputs pertain to characterization at the whole-plant level. The output of the model is accumulated dry matter partitioned among leaves, stems, and roots; thus, the elementary processes clearly operate under the constraints of the plant structure which is itself the output of the model.

Bridging the gap between PAT concepts and implementation: An integrated software platform for fermentation.

PubMed

Chopda, Viki R; Gomes, James; Rathore, Anurag S

2016-01-01

Bioreactor control significantly impacts both the amount and quality of the product being manufactured. The complexity of the control strategy that is implemented increases with reactor size, which may vary from thousands to tens of thousands of litres in commercial manufacturing. The Process Analytical Technology (PAT) initiative has highlighted the need for having robust monitoring tools and effective control schemes that are capable of taking real time information about the critical quality attributes (CQA) and the critical process parameters (CPP) and executing immediate response as soon as a deviation occurs. However, the limited flexibility that present commercial software packages offer creates a hurdle. Visual programming environments have gradually emerged as potential alternatives to the available text based languages. This paper showcases development of an integrated programme using a visual programming environment for a Sartorius BIOSTAT® B Plus 5L bioreactor through which various peripheral devices are interfaced. The proposed programme facilitates real-time access to data and allows for execution of control actions to follow the desired trajectory. Major benefits of such integrated software system include: (i) improved real time monitoring and control; (ii) reduced variability; (iii) improved performance; (iv) reduced operator-training time; (v) enhanced knowledge management; and (vi) easier PAT implementation. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A containerless levitation setup for liquid processing in a superconducting magnet.

PubMed

Lu, Hui-Meng; Yin, Da-Chuan; Li, Hai-Sheng; Geng, Li-Qiang; Zhang, Chen-Yan; Lu, Qin-Qin; Guo, Yun-Zhu; Guo, Wei-Hong; Shang, Peng; Wakayama, Nobuko I

2008-09-01

Containerless processing of materials is considered beneficial for obtaining high quality products due to the elimination of the detrimental effects coming from the contact with container walls. Many containerless processing methods are realized by levitation techniques. This paper describes a containerless levitation setup that utilized the magnetization force generated in a gradient magnetic field. It comprises a levitation unit, a temperature control unit, and a real-time observation unit. Known volume of liquid diamagnetic samples can be levitated in the levitation chamber, the temperature of which is controlled using the temperature control unit. The evolution of the levitated sample is observed in real time using the observation unit. With this setup, containerless processing of liquid such as crystal growth from solution can be realized in a well-controlled manner. Since the levitation is achieved using a superconducting magnet, experiments requiring long duration time such as protein crystallization and simulation of space environment for living system can be easily succeeded.

Power control electronics for cryogenic instrumentation

NASA Technical Reports Server (NTRS)

Ray, Biswajit; Gerber, Scott S.; Patterson, Richard L.; Myers, Ira T.

1995-01-01

In order to achieve a high-efficiency high-density cryogenic instrumentation system, the power processing electronics should be placed in the cold environment along with the sensors and signal-processing electronics. The typical instrumentation system requires low voltage dc usually obtained from processing line frequency ac power. Switch-mode power conversion topologies such as forward, flyback, push-pull, and half-bridge are used for high-efficiency power processing using pulse-width modulation (PWM) or resonant control. This paper presents several PWM and multiresonant power control circuits, implemented using commercially available CMOS and BiCMOS integrated circuits, and their performance at liquid-nitrogen temperature (77 K) as compared to their room temperature (300 K) performance. The operation of integrated circuits at cryogenic temperatures results in an improved performance in terms of increased speed, reduced latch-up susceptibility, reduced leakage current, and reduced thermal noise. However, the switching noise increased at 77 K compared to 300 K. The power control circuits tested in the laboratory did successfully restart at 77 K.

LABORATORY PROCESS CONTROLLER USING NATURAL LANGUAGE COMMANDS FROM A PERSONAL COMPUTER

NASA Technical Reports Server (NTRS)

Will, H.

1994-01-01

The complex environment of the typical research laboratory requires flexible process control. This program provides natural language process control from an IBM PC or compatible machine. Sometimes process control schedules require changes frequently, even several times per day. These changes may include adding, deleting, and rearranging steps in a process. This program sets up a process control system that can either run without an operator, or be run by workers with limited programming skills. The software system includes three programs. Two of the programs, written in FORTRAN77, record data and control research processes. The third program, written in Pascal, generates the FORTRAN subroutines used by the other two programs to identify the user commands with the user-written device drivers. The software system also includes an input data set which allows the user to define the user commands which are to be executed by the computer. To set the system up the operator writes device driver routines for all of the controlled devices. Once set up, this system requires only an input file containing natural language command lines which tell the system what to do and when to do it. The operator can make up custom commands for operating and taking data from external research equipment at any time of the day or night without the operator in attendance. This process control system requires a personal computer operating under MS-DOS with suitable hardware interfaces to all controlled devices. The program requires a FORTRAN77 compiler and user-written device drivers. This program was developed in 1989 and has a memory requirement of about 62 Kbytes.

Integrating automated support for a software management cycle into the TAME system

NASA Technical Reports Server (NTRS)

Sunazuka, Toshihiko; Basili, Victor R.

1989-01-01

Software managers are interested in the quantitative management of software quality, cost and progress. An integrated software management methodology, which can be applied throughout the software life cycle for any number purposes, is required. The TAME (Tailoring A Measurement Environment) methodology is based on the improvement paradigm and the goal/question/metric (GQM) paradigm. This methodology helps generate a software engineering process and measurement environment based on the project characteristics. The SQMAR (software quality measurement and assurance technology) is a software quality metric system and methodology applied to the development processes. It is based on the feed forward control principle. Quality target setting is carried out before the plan-do-check-action activities are performed. These methodologies are integrated to realize goal oriented measurement, process control and visual management. A metric setting procedure based on the GQM paradigm, a management system called the software management cycle (SMC), and its application to a case study based on NASA/SEL data are discussed. The expected effects of SMC are quality improvement, managerial cost reduction, accumulation and reuse of experience, and a highly visual management reporting system.

Applications of CELSS technology to controlled environment agriculture

NASA Technical Reports Server (NTRS)

Bates, Maynard E.; Bubenheim, David L.

1991-01-01

Controlled environment agriculture (CEA) is defined as the use of environmental manipulation for the commercial production of organisms, whether plants or animals. While many of the technologies necessary for aquaculture systems in North America is nevertheless doubling approximately every five years. Economic, cultural, and environmental pressures all favor CEA over field production for many non-commodity agricultural crops. Many countries around the world are already dependent on CEA for much of their fresh food. Controlled ecological life support systems (CELSS), under development at ARC, KSC, and JSC expand the concept of CEA to the extent that all human requirements for food, oxygen, and water will be provided regenerated by processing of waste streams to supply plant inputs. The CELSS will likely contain plants, humans, possibly other animals, microorganisms and physically and chemical processors. In effect, NASA will create engineered ecosystems. In the process of developing the technology for CELSS, NASA will develop information and technology which will be applied to improving the efficiency, reliability, and cost effectiveness for CEA, improving its resources recycling capabilities, and lessening its environmental impact to negligible levels.

Development of A General Principle Solution Forisoagrinet Compliant Networking System Components in Animal Husbandry

NASA Astrophysics Data System (ADS)

Kuhlmann, Arne; Herd, Daniel; Röβler, Benjamin; Gallmann, Eva; Jungbluth, Thomas

In pig production software and electronic systems are widely used for process control and management. Unfortunately most devices on farms are proprietary solutions and autonomically working. To unify data communication of devices in agricultural husbandry, the international standard ISOagriNET (ISO 17532:2007) was developed. It defines data formats and exchange protocols, to link up devices like climate controls, feeding systems and sensors, but also management software. The aim of the research project, "Information and Data Collection in Livestock Systems" is to develop an ISOagriNET compliant IT system, a so called Farming Cell. It integrates all electronic components to acquire the available data and information for pig fattening. That way, an additional benefit to humans, animals and the environment regarding process control and documentation, can be generated. Developing the Farming Cell is very complex; in detail it is very difficult and long-winded to integrate hardware and software by various vendors into an ISOagriNET compliant IT system. This ISOagriNET prototype shows as a test environment the potential of this new standard.

A Web-Based System for Monitoring and Controlling Multidisciplinary Design Projects

NASA Technical Reports Server (NTRS)

Salas, Andrea O.; Rogers, James L.

1997-01-01

In today's competitive environment, both industry and government agencies are under enormous pressure to reduce the time and cost of multidisciplinary design projects. A number of frameworks have been introduced to assist in this process by facilitating the integration of and communication among diverse disciplinary codes. An examination of current frameworks reveals weaknesses in various areas such as sequencing, displaying, monitoring, and controlling the design process. The objective of this research is to explore how Web technology, in conjunction with an existing framework, can improve these areas of weakness. This paper describes a system that executes a sequence of programs, monitors and controls the design process through a Web-based interface, and visualizes intermediate and final results through the use of Java(Tm) applets. A small sample problem, which includes nine processes with two analysis programs that are coupled to an optimizer, is used to demonstrate the feasibility of this approach.

Total systems design analysis of high performance structures

NASA Technical Reports Server (NTRS)

Verderaime, V.

1993-01-01

Designer-control parameters were identified at interdiscipline interfaces to optimize structural systems performance and downstream development and operations with reliability and least life-cycle cost. Interface tasks and iterations are tracked through a matrix of performance disciplines integration versus manufacturing, verification, and operations interactions for a total system design analysis. Performance integration tasks include shapes, sizes, environments, and materials. Integrity integrating tasks are reliability and recurring structural costs. Significant interface designer control parameters were noted as shapes, dimensions, probability range factors, and cost. Structural failure concept is presented, and first-order reliability and deterministic methods, benefits, and limitations are discussed. A deterministic reliability technique combining benefits of both is proposed for static structures which is also timely and economically verifiable. Though launch vehicle environments were primarily considered, the system design process is applicable to any surface system using its own unique filed environments.

Neuroscientific Model of Motivational Process

PubMed Central

Kim, Sung-il

2013-01-01

Considering the neuroscientific findings on reward, learning, value, decision-making, and cognitive control, motivation can be parsed into three sub processes, a process of generating motivation, a process of maintaining motivation, and a process of regulating motivation. I propose a tentative neuroscientific model of motivational processes which consists of three distinct but continuous sub processes, namely reward-driven approach, value-based decision-making, and goal-directed control. Reward-driven approach is the process in which motivation is generated by reward anticipation and selective approach behaviors toward reward. This process recruits the ventral striatum (reward area) in which basic stimulus-action association is formed, and is classified as an automatic motivation to which relatively less attention is assigned. By contrast, value-based decision-making is the process of evaluating various outcomes of actions, learning through positive prediction error, and calculating the value continuously. The striatum and the orbitofrontal cortex (valuation area) play crucial roles in sustaining motivation. Lastly, the goal-directed control is the process of regulating motivation through cognitive control to achieve goals. This consciously controlled motivation is associated with higher-level cognitive functions such as planning, retaining the goal, monitoring the performance, and regulating action. The anterior cingulate cortex (attention area) and the dorsolateral prefrontal cortex (cognitive control area) are the main neural circuits related to regulation of motivation. These three sub processes interact with each other by sending reward prediction error signals through dopaminergic pathway from the striatum and to the prefrontal cortex. The neuroscientific model of motivational process suggests several educational implications with regard to the generation, maintenance, and regulation of motivation to learn in the learning environment. PMID:23459598

Neuroscientific model of motivational process.

PubMed

Kim, Sung-Il

2013-01-01

Considering the neuroscientific findings on reward, learning, value, decision-making, and cognitive control, motivation can be parsed into three sub processes, a process of generating motivation, a process of maintaining motivation, and a process of regulating motivation. I propose a tentative neuroscientific model of motivational processes which consists of three distinct but continuous sub processes, namely reward-driven approach, value-based decision-making, and goal-directed control. Reward-driven approach is the process in which motivation is generated by reward anticipation and selective approach behaviors toward reward. This process recruits the ventral striatum (reward area) in which basic stimulus-action association is formed, and is classified as an automatic motivation to which relatively less attention is assigned. By contrast, value-based decision-making is the process of evaluating various outcomes of actions, learning through positive prediction error, and calculating the value continuously. The striatum and the orbitofrontal cortex (valuation area) play crucial roles in sustaining motivation. Lastly, the goal-directed control is the process of regulating motivation through cognitive control to achieve goals. This consciously controlled motivation is associated with higher-level cognitive functions such as planning, retaining the goal, monitoring the performance, and regulating action. The anterior cingulate cortex (attention area) and the dorsolateral prefrontal cortex (cognitive control area) are the main neural circuits related to regulation of motivation. These three sub processes interact with each other by sending reward prediction error signals through dopaminergic pathway from the striatum and to the prefrontal cortex. The neuroscientific model of motivational process suggests several educational implications with regard to the generation, maintenance, and regulation of motivation to learn in the learning environment.

Context-aware access control for pervasive access to process-based healthcare systems.

PubMed

Koufi, Vassiliki; Vassilacopoulos, George

2008-01-01

Healthcare is an increasingly collaborative enterprise involving a broad range of healthcare services provided by many individuals and organizations. Grid technology has been widely recognized as a means for integrating disparate computing resources in the healthcare field. Moreover, Grid portal applications can be developed on a wireless and mobile infrastructure to execute healthcare processes which, in turn, can provide remote access to Grid database services. Such an environment provides ubiquitous and pervasive access to integrated healthcare services at the point of care, thus improving healthcare quality. In such environments, the ability to provide an effective access control mechanism that meets the requirement of the least privilege principle is essential. Adherence to the least privilege principle requires continuous adjustments of user permissions in order to adapt to the current situation. This paper presents a context-aware access control mechanism for HDGPortal, a Grid portal application which provides access to workflow-based healthcare processes using wireless Personal Digital Assistants. The proposed mechanism builds upon and enhances security mechanisms provided by the Grid Security Infrastructure. It provides tight, just-in-time permissions so that authorized users get access to specific objects according to the current context. These permissions are subject to continuous adjustments triggered by the changing context. Thus, the risk of compromising information integrity during task executions is reduced.

Scripting human animations in a virtual environment

NASA Technical Reports Server (NTRS)

Goldsby, Michael E.; Pandya, Abhilash K.; Maida, James C.

1994-01-01

The current deficiencies of virtual environment (VE) are well known: annoying lag time in drawing the current view, drastically simplified environments to reduce that time lag, low resolution and narrow field of view. Animation scripting is an application of VE technology which can be carried out successfully despite these deficiencies. The final product is a smoothly moving high resolution animation displaying detailed models. In this system, the user is represented by a human computer model with the same body proportions. Using magnetic tracking, the motions of the model's upper torso, head and arms are controlled by the user's movements (18 degrees of freedom). The model's lower torso and global position and orientation are controlled by a spaceball and keypad (12 degrees of freedom). Using this system human motion scripts can be extracted from the user's movements while immersed in a simplified virtual environment. Recorded data is used to define key frames; motion is interpolated between them and post processing adds a more detailed environment. The result is a considerable savings in time and a much more natural-looking movement of a human figure in a smooth and seamless animation.

An Extended Petri-Net Based Approach for Supply Chain Process Enactment in Resource-Centric Web Service Environment

NASA Astrophysics Data System (ADS)

Wang, Xiaodong; Zhang, Xiaoyu; Cai, Hongming; Xu, Boyi

Enacting a supply-chain process involves variant partners and different IT systems. REST receives increasing attention for distributed systems with loosely coupled resources. Nevertheless, resource model incompatibilities and conflicts prevent effective process modeling and deployment in resource-centric Web service environment. In this paper, a Petri-net based framework for supply-chain process integration is proposed. A resource meta-model is constructed to represent the basic information of resources. Then based on resource meta-model, XML schemas and documents are derived, which represent resources and their states in Petri-net. Thereafter, XML-net, a high level Petri-net, is employed for modeling control and data flow of process. From process model in XML-net, RESTful services and choreography descriptions are deduced. Therefore, unified resource representation and RESTful services description are proposed for cross-system integration in a more effective way. A case study is given to illustrate the approach and the desirable features of the approach are discussed.

Sanitizing in Dry-Processing Environments Using Isopropyl Alcohol Quaternary Ammonium Formula.

PubMed

Kane, Deborah M; Getty, Kelly J K; Mayer, Brian; Mazzotta, Alejandro

2016-01-01

Dry-processing environments are particularly challenging to clean and sanitize because introduced water can favor growth and establishment of pathogenic microorganisms such as Salmonella. Our objective was to determine the efficacy of an isopropyl alcohol quaternary ammonium (IPAQuat) formula for eliminating potential Salmonella contamination on food contact surfaces. Clean stainless steel coupons and conveyor belt materials used in dry-processing environments were spot inoculated in the center of coupons (5 by 5 cm) with a six-serotype composite of Salmonella (approximately 10 log CFU/ml), subjected to IPAQuat sanitizer treatments with exposure times of 30 s, 1 min, or 5 min, and then swabbed for enumeration of posttreatment survivors. A subset of inoculated surfaces was soiled with a breadcrumb-flour blend and allowed to sit on the laboratory bench for a minimum of 16 h before sanitation. Pretreatment Salmonella populations (inoculated controls, 0 s treatment) were approximately 7.0 log CFU/25 cm(2), and posttreatment survivors were 1.31, 0.72, and < 0.7 (detection limit) log CFU/25 cm(2) after sanitizer exposure for 30 s, 1 min, or 5 min, respectively, for both clean (no added soil) and soiled surfaces. Treatment with the IPAQuat formula using 30-s sanitizer exposures resulted in 5.68-log reductions, whereas >6.0-log reductions were observed for sanitizer exposures of 1 and 5 min. Because water is not introduced into the processing environment with this approach, the IPAQuat formula could have sanitation applications in dry-processing environments to eliminate potential contamination from Salmonella on food contact surfaces.

Cross-correlation between the controlled collision environment and real-world motor vehicle collisions: Evaluating the protection of the thoracic side airbag.

PubMed

Gaylor, Luke; Junge, Mirko; Abanteriba, Sylvester

2018-05-19

Thoracic side airbags (tSABs) were integrated into the vehicle fleet to attenuate and distribute forces on the occupant's chest and abdomen, dissipate the impact energy, and move the occupant away from the intruding structure, all of which reduce the risk of injury. This research piece investigates and evaluates the safety performance of the airbag unit by cross-correlating data from a controlled collision environment with field data. We focus exclusively on vehicle-vehicle lateral impacts from the NHTSA's Vehicle Crash Test Database and NASS-CDS database, which are replicated in the controlled environment by the (crabbed) barrier impact. Similar collisions with and without seat-embedded tSABs are matched to each other and the injury risks are compared. Results indicated that dummy-based thoracic injury metrics were significantly lower with tSAB exposure (P <.001). Yet, when the controlled collision environment data were cross-correlated with NASS-CDS collisions, deployment of the tSAB indicated no association with thoracic injury (tho. MAIS 2+ unadjusted relative risk [RR] = 1.14; 90% confidence interval [CI], 0.80-1.62; tho. MAIS 3+ unadjusted RR = 1.12; 90% CI, 0.76-1.65). The data from the controlled collision environment indicated an unequivocal benefit provided by the thoracic side airbag for the crash dummy; however, the real-world collisions demonstrate that no benefit is provided to the occupant. This has resulted from a noncorrelation between the crash test/dummy-based design taking the abstracting process too far to represent the real-world collision scenario.

Quartz OSL Dating of the loess deposit in the eastern Tibetan Plateau and its environment implications since the Last Glaciation

NASA Astrophysics Data System (ADS)

Yang, S.; Cheng, T.; Liu, W.; Fang, X.

2017-12-01

Loess deposit is widespread in the Chuanxi Plateau, the eastern Tibetan Plateau, which is a critical archive for understanding the aeolian process, the evolution of the westerly and the environment changes on the Plateau. Previous studies have shown its aeolian origin, and mainly transported by wind from the western part of the Tibetan Plateau. However, the aeolian processes of the loess and its environment implications are not well understood mainly due to lack of detailed age controls. We carry out a combined quartz optically stimulated luminescence (OSL) dating and accelerator mass spectrometry radiocarbon dating (AMS 14-C) for the loess deposits in Garzê and Jinchuan. The results indicate that the quartz OSL dating can provide reliable age controls for the loess-paleosol sequences from the Chuanxi Plateau, showing the potential of OSL to date loess in the high altitude region. The results indicate that the OSL ages are in agreement with the observed stratigraphy in the field. The constructed OSL and AMS 14-C chronology of the Garzê loess reveals that the widespread loess in Ganzi Region deposited since the Last Glacial. The dust accumulation is rapid during marine isotope stage (MIS) 3 and 2, and a relative low accumulation rate in the Holocene, which may related with the desertification processes of the inner Tibetan Plateau.

Materials science research in microgravity

NASA Technical Reports Server (NTRS)

Perepezko, John H.

1992-01-01

There are several important attributes of an extended duration microgravity environment that offer a new dimension in the control of the microstructure, processing, and properties of materials. First, when gravitational effects are minimized, buoyancy driven convection flows are also minimized. The flows due to density differences, brought about either by composition or temperature gradients will then be reduced or eliminated to permit a more precise control of the temperature and the composition of a melt which is critical in achieving high quality crystal growth of electronic materials or alloy structures. Secondly, body force effects such as sedimentation, hydrostatic pressure, and deformation are similarly reduced. These effects may interfere with attempts to produce uniformly dispersed or aligned second phases during melt solidification. Thirdly, operating in a microgravity environment will facilitate the containerless processing of melts to eliminate the limitations of containment for reactive melts. The noncontacting forces such as those developed from electromagnet, electrostatic, or acoustic fields can be used to position samples. With this mode of operation, contamination can be minimized to enable the study of reactive melts and to eliminate extraneous crystal nucleation so that novel crystalline structures and new glass compositions may be produced. In order to take advantage of the microgravity environment for materials research, it has become clear that reliable processing models based on a sound ground based experimental experience and an established thermophysical property data base are essential.

Containerless processing at high temperatures using acoustic levitation

NASA Technical Reports Server (NTRS)

Rey, C. A.; Merkley, D. R.; Hampton, S.; Devos, J.; Mapes-Riordan, D.; Zatarski, M.

1991-01-01

Advanced techniques are presented which facilitate the development of inert or reducing atmospheres in excess of 2000 K in order to improve processing of containerless capabilities at higher temperatures and to provide more contamination-free environments. Recent testing, in the laboratory and aboard the NASA KC-135 aircraft, of a high-temperature acoustic positioner demonstrated the effectiveness of a specimen motion damping system and of specimen spin control. It is found that stable positioning can be achieved under ambient and heated conditions, including the transient states of heat-up and cool-down. An incorporated high-temperature levitator was found capable of processing specimens of up to 6-mm diameter in a high-purity environment without the contaminating effects of a container at high temperatures and with relative quiescence.

Software life cycle methodologies and environments

NASA Technical Reports Server (NTRS)

Fridge, Ernest

1991-01-01

Products of this project will significantly improve the quality and productivity of Space Station Freedom Program software processes by: improving software reliability and safety; and broadening the range of problems that can be solved with computational solutions. Projects brings in Computer Aided Software Engineering (CASE) technology for: Environments such as Engineering Script Language/Parts Composition System (ESL/PCS) application generator, Intelligent User Interface for cost avoidance in setting up operational computer runs, Framework programmable platform for defining process and software development work flow control, Process for bringing CASE technology into an organization's culture, and CLIPS/CLIPS Ada language for developing expert systems; and methodologies such as Method for developing fault tolerant, distributed systems and a method for developing systems for common sense reasoning and for solving expert systems problems when only approximate truths are known.

Foundational Report Series: Advanced Distribution Management Systems for Grid Modernization, High-Level Use Cases for DMS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Jianhui; Lu, Xiaonan; Martino, Sal

Many distribution management systems (DMS) projects have achieved limited success because the electric utility did not sufficiently plan for actual use of the DMS functions in the control room environment. As a result, end users were not clear on how to use the new application software in actual production environments with existing, well-established business processes. An important first step in the DMS implementation process is development and refinement of the “to be” business processes. Development of use cases for the required DMS application functions is a key activity that leads to the formulation of the “to be” requirements. It ismore » also an important activity that is needed to develop specifications that are used to procure a new DMS.« less

Widening the adoption of workflows to include human and human-machine scientific processes

NASA Astrophysics Data System (ADS)

Salayandia, L.; Pinheiro da Silva, P.; Gates, A. Q.

2010-12-01

Scientific workflows capture knowledge in the form of technical recipes to access and manipulate data that help scientists manage and reuse established expertise to conduct their work. Libraries of scientific workflows are being created in particular fields, e.g., Bioinformatics, where combined with cyber-infrastructure environments that provide on-demand access to data and tools, result in powerful workbenches for scientists of those communities. The focus in these particular fields, however, has been more on automating rather than documenting scientific processes. As a result, technical barriers have impeded a wider adoption of scientific workflows by scientific communities that do not rely as heavily on cyber-infrastructure and computing environments. Semantic Abstract Workflows (SAWs) are introduced to widen the applicability of workflows as a tool to document scientific recipes or processes. SAWs intend to capture a scientists’ perspective about the process of how she or he would collect, filter, curate, and manipulate data to create the artifacts that are relevant to her/his work. In contrast, scientific workflows describe the process from the point of view of how technical methods and tools are used to conduct the work. By focusing on a higher level of abstraction that is closer to a scientist’s understanding, SAWs effectively capture the controlled vocabularies that reflect a particular scientific community, as well as the types of datasets and methods used in a particular domain. From there on, SAWs provide the flexibility to adapt to different environments to carry out the recipes or processes. These environments range from manual fieldwork to highly technical cyber-infrastructure environments, i.e., such as those already supported by scientific workflows. Two cases, one from Environmental Science and another from Geophysics, are presented as illustrative examples.

FUNCTIONAL BIOMATERIALS: Design of Novel Biomaterials

NASA Astrophysics Data System (ADS)

Sakiyama-Elbert, Se; Hubbell, Ja

2001-08-01

The field of biomaterials has recently been focused on the design of intelligent materials. Toward this goal, materials have been developed that can provide specific bioactive signals to control the biological environment around them during the process of materials integration and wound healing. In addition, materials have been developed that can respond to changes in their environment, such as a change in pH or cell-associated enzymatic activity. In designing such novel biomaterials, researchers have sought not merely to create bio-inert materials, but rather materials that can respond to the cellular environment around them to improve device integration and tissue regeneration.

3DUI assisted lower and upper member therapy.

PubMed

Uribe-Quevedo, Alvaro; Perez-Gutierrez, Byron

2012-01-01

3DUIs are becoming very popular among researchers, developers and users as they allow more immersive and interactive experiences by taking advantage of the human dexterity. The features offered by these interfaces outside the gaming environment, have allowed the development of applications in the medical area by enhancing the user experience and aiding the therapy process in controlled and monitored environments. Using mainstream videogame 3DUIs based on inertial and image sensors available in the market, this work presents the development of a virtual environment and its navigation through lower member captured gestures for assisting motion during therapy.

Integrated flexible manufacturing program for manufacturing automation and rapid prototyping

NASA Technical Reports Server (NTRS)

Brooks, S. L.; Brown, C. W.; King, M. S.; Simons, W. R.; Zimmerman, J. J.

1993-01-01

The Kansas City Division of Allied Signal Inc., as part of the Integrated Flexible Manufacturing Program (IFMP), is developing an integrated manufacturing environment. Several systems are being developed to produce standards and automation tools for specific activities within the manufacturing environment. The Advanced Manufacturing Development System (AMDS) is concentrating on information standards (STEP) and product data transfer; the Expert Cut Planner system (XCUT) is concentrating on machining operation process planning standards and automation capabilities; the Advanced Numerical Control system (ANC) is concentrating on NC data preparation standards and NC data generation tools; the Inspection Planning and Programming Expert system (IPPEX) is concentrating on inspection process planning, coordinate measuring machine (CMM) inspection standards and CMM part program generation tools; and the Intelligent Scheduling and Planning System (ISAPS) is concentrating on planning and scheduling tools for a flexible manufacturing system environment. All of these projects are working together to address information exchange, standardization, and information sharing to support rapid prototyping in a Flexible Manufacturing System (FMS) environment.

Reproduction numbers for infections with free-living pathogens growing in the environment.

PubMed

Bani-Yaghoub, Majid; Gautam, Raju; Shuai, Zhisheng; van den Driessche, P; Ivanek, Renata

2012-01-01

The basic reproduction number ℛ(0) for a compartmental disease model is often calculated by the next generation matrix (NGM) approach. When the interactions within and between disease compartments are interpreted differently, the NGM approach may lead to different ℛ(0) expressions. This is demonstrated by considering a susceptible-infectious-recovered-susceptible model with free-living pathogen (FLP) growing in the environment. Although the environment could play different roles in the disease transmission process, leading to different ℛ(0) expressions, there is a unique type reproduction number when control strategies are applied to the host population. All ℛ(0) expressions agree on the threshold value 1 and preserve their order of magnitude. However, using data for salmonellosis and cholera, it is shown that the estimated ℛ(0) values are substantially different. This study highlights the utility and limitations of reproduction numbers to accurately quantify the effects of control strategies for infections with FLPs growing in the environment.

40 CFR 763.165 - Manufacture and importation prohibitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Manufacture and importation...) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Prohibition of the Manufacture, Importation, Processing, and Distribution in Commerce of Certain Asbestos-Containing Products; Labeling Requirements § 763.165 Manufacture...

NASCAP user's manual, 1978

NASA Technical Reports Server (NTRS)

Cassidy, J. J., III

1978-01-01

NASCAP simulates the charging process for a complex object in either tenuous plasma (geosynchronous orbit) or ground test (electron gun source) environment. Program control words, the structure of user input files, and various user options available are described in this computer programmer's user manual.

APPROACHES TO CHARACTERIZING SOLID PHASE ARSENIC SPECIATION IN SOILS

EPA Science Inventory

The partitioning of arsenic to soil solids is an important process controlling the stabilization of arsenic wastes and mobility of arsenic in the environment. Identification of the physicochemical characteristics of the partitioning mechanism(s) is important for treatment op...

40 CFR 761.340 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT... Accordance With § 761.62, and Sampling PCB Remediation Waste Destined for Off-Site Disposal, in Accordance... generate new waste. (c) Non-liquid PCB remediation waste from processes that continuously generate new...

40 CFR 761.340 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT... Accordance With § 761.62, and Sampling PCB Remediation Waste Destined for Off-Site Disposal, in Accordance... generate new waste. (c) Non-liquid PCB remediation waste from processes that continuously generate new...

40 CFR 761.340 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT... Accordance With § 761.62, and Sampling PCB Remediation Waste Destined for Off-Site Disposal, in Accordance... generate new waste. (c) Non-liquid PCB remediation waste from processes that continuously generate new...

Heteroaggregation of cerium oxide nanoparticles and nanoparticles of pyrolyzed biomass

USDA-ARS?s Scientific Manuscript database

Heteroaggregation with indigenous particles is an important process controlling the mobility of engineered nanomaterials in the environment. We studied heteroaggregation of cerium oxide nanoparticles (n-CeO2), which are widely used commercially, with nanoparticles of pyrogenic carbonaceous material ...

Hands-free device control using sound picked up in the ear canal

NASA Astrophysics Data System (ADS)

Chhatpar, Siddharth R.; Ngia, Lester; Vlach, Chris; Lin, Dong; Birkhimer, Craig; Juneja, Amit; Pruthi, Tarun; Hoffman, Orin; Lewis, Tristan

2008-04-01

Hands-free control of unmanned ground vehicles is essential for soldiers, bomb disposal squads, and first responders. Having their hands free for other equipment and tasks allows them to be safer and more mobile. Currently, the most successful hands-free control devices are speech-command based. However, these devices use external microphones, and in field environments, e.g., war zones and fire sites, their performance suffers because of loud ambient noise: typically above 90dBA. This paper describes the development of technology using the ear as an output source that can provide excellent command recognition accuracy even in noisy environments. Instead of picking up speech radiating from the mouth, this technology detects speech transmitted internally through the ear canal. Discreet tongue movements also create air pressure changes within the ear canal, and can be used for stealth control. A patented earpiece was developed with a microphone pointed into the ear canal that captures these signals generated by tongue movements and speech. The signals are transmitted from the earpiece to an Ultra-Mobile Personal Computer (UMPC) through a wired connection. The UMPC processes the signals and utilizes them for device control. The processing can include command recognition, ambient noise cancellation, acoustic echo cancellation, and speech equalization. Successful control of an iRobot PackBot has been demonstrated with both speech (13 discrete commands) and tongue (5 discrete commands) signals. In preliminary tests, command recognition accuracy was 95% with speech control and 85% with tongue control.

The environment of professional practice and Burnout in nurses in primary healthcare

PubMed Central

Lorenz, Vera Regina; Guirardello, Edinêis de Brito

2014-01-01

OBJECTIVES: to assess how nurses perceive autonomy, control over the environment, the professional relationship between nurses and physicians and the organizational support and correlate them with burnout, satisfaction at work, quality of work and the intention to quit work in primary healthcare. METHOD: cross-sectional and correlation study, using a sample of 198 nurses. The tools used were the Nursing Work Index Revised, Maslach Burnout Inventory and a form to characterize the nurses. To analyze the data, descriptive statistics were applied and Spearman's correlation coefficient was used. RESULTS: the nurses assessed that the environment is partially favorable for: autonomy, professional relationship and organizational support and that the control over this environment is limited. Significant correlations were evidenced between the Nursing Work Index Revised, Maslach Burnout Inventory and the variables: satisfaction at work, quality of care and the intent to quit the job. CONCLUSION: the nurses' perceptions regarding the environment of practice are correlated with burnout, satisfaction at work, quality of care and the intent to quit the job. This study provides support for the restructuring of work processes in the primary health care environment and for communication among the health service management, human resources and occupational health areas. PMID:25517928