High level language for measurement complex control based on the computer E-100I

NASA Technical Reports Server (NTRS)

Zubkov, B. V.

1980-01-01

A high level language was designed to control the process of conducting an experiment using the computer "Elektrinika-1001". Program examples are given to control the measuring and actuating devices. The procedure of including these programs in the suggested high level language is described.

Fuzzy control for a nonlinear mimo-liquid level problem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, R. E.; Mortensen, F. N.; Wantuck, P. J.

2001-01-01

Nonlinear systems are very common in the chemical process industries. Control of these systems, particularly multivariable systems, is extremely difficult. In many chemical plants, because of this difficulty, control is seldom optimal. Quite often, the best control is obtained in the manual mode using experienced operators. Liquid level control is probably one of the most common control problems in a chemical plant. Liquid level is important in heat exchanger control where heat and mass transfer rates can be controlled by the amount of liquid covering the tubes. Distillation columns, mixing tanks, and surge tanks are other examples where liquid levelmore » control is very important. The problem discussed in this paper is based on the simultaneous level control of three tanks connected in series. Each tank holds slightly less than 0.01 m{sup 3} of liquid. All three tanks are connected, Liquid is pumped into the first and the third tanks to maintain their levels. The third tank in the series drains to the system exit. The levels in the first and third tank control the level in the middle tank. The level in the middle tank affects the levels in the two end tanks. Many other chemical plant systems can be controlled in a manner similar to this three-tank system. For example, in any distillation column liquid level control problems can be represented as a total condenser with liquid level control, a reboiler with liquid level control, with the interactive column in between. The solution to the three-tank-problem can provide insight into many of the nonlinear control problems in the chemical process industries. The system was tested using the fuzzy logic controller and a proportional-integral (PI) controller, in both the setpoint tracking mode and disturbance rejection mode. The experimental results are discussed and comparisons between fuzzy controller and the standard PI controller are made.« less

Level indicator for pressure vessels

DOEpatents

Not Available

1982-04-28

A liquid-level monitor for tracking the level of a coal slurry in a high-pressure vessel including a toroidal-shaped float with magnetically permeable bands thereon disposed within the vessel, two pairs of magnetic-field generators and detectors disposed outside the vessel adjacent the top and bottom thereof and magnetically coupled to the magnetically permeable bands on the float, and signal-processing circuitry for combining signals from the top and bottom detectors for generating a monotonically increasing analog control signal which is a function of liquid level. The control signal may be utilized to operate high-pressure control valves associated with processes in which the high-pressure vessel is used.

High pressure liquid level monitor

DOEpatents

Bean, Vern E.; Long, Frederick G.

1984-01-01

A liquid level monitor for tracking the level of a coal slurry in a high-pressure vessel including a toroidal-shaped float with magnetically permeable bands thereon disposed within the vessel, two pairs of magnetic field generators and detectors disposed outside the vessel adjacent the top and bottom thereof and magnetically coupled to the magnetically permeable bands on the float, and signal processing circuitry for combining signals from the top and bottom detectors for generating a monotonically increasing analog control signal which is a function of liquid level. The control signal may be utilized to operate high-pressure control valves associated with processes in which the high-pressure vessel is used.

40 CFR 60.5430 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... control vessels, bottoms receivers or knockout vessels. (3) Pressure vessels designed to operate in excess... supply natural gas to the process control device (e.g., level control, temperature control, pressure control) where the supply gas pressure is modulated by the process condition, and then flows to the valve...

29 CFR 1910.95 - Occupational noise exposure.

Code of Federal Regulations, 2012 CFR

2012-07-01

... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Occupational Health and Environmental Control § 1910.95 Occupational... engineering controls shall be utilized. If such controls fail to reduce sound levels within the levels of...) Monitoring shall be repeated whenever a change in production, process, equipment or controls increases noise...

29 CFR 1910.95 - Occupational noise exposure.

Code of Federal Regulations, 2014 CFR

2014-07-01

... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Occupational Health and Environmental Control § 1910.95 Occupational... engineering controls shall be utilized. If such controls fail to reduce sound levels within the levels of...) Monitoring shall be repeated whenever a change in production, process, equipment or controls increases noise...

29 CFR 1910.95 - Occupational noise exposure.

Code of Federal Regulations, 2011 CFR

2011-07-01

... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Occupational Health and Environmental Control § 1910.95 Occupational... engineering controls shall be utilized. If such controls fail to reduce sound levels within the levels of...) Monitoring shall be repeated whenever a change in production, process, equipment or controls increases noise...

Feasibility study of using statistical process control to customized quality assurance in proton therapy.

PubMed

Rah, Jeong-Eun; Shin, Dongho; Oh, Do Hoon; Kim, Tae Hyun; Kim, Gwe-Ya

2014-09-01

To evaluate and improve the reliability of proton quality assurance (QA) processes and, to provide an optimal customized tolerance level using the statistical process control (SPC) methodology. The authors investigated the consistency check of dose per monitor unit (D/MU) and range in proton beams to see whether it was within the tolerance level of the daily QA process. This study analyzed the difference between the measured and calculated ranges along the central axis to improve the patient-specific QA process in proton beams by using process capability indices. The authors established a customized tolerance level of ±2% for D/MU and ±0.5 mm for beam range in the daily proton QA process. In the authors' analysis of the process capability indices, the patient-specific range measurements were capable of a specification limit of ±2% in clinical plans. SPC methodology is a useful tool for customizing the optimal QA tolerance levels and improving the quality of proton machine maintenance, treatment delivery, and ultimately patient safety.

Integrating end-to-end threads of control into object-oriented analysis and design

NASA Technical Reports Server (NTRS)

Mccandlish, Janet E.; Macdonald, James R.; Graves, Sara J.

1993-01-01

Current object-oriented analysis and design methodologies fall short in their use of mechanisms for identifying threads of control for the system being developed. The scenarios which typically describe a system are more global than looking at the individual objects and representing their behavior. Unlike conventional methodologies that use data flow and process-dependency diagrams, object-oriented methodologies do not provide a model for representing these global threads end-to-end. Tracing through threads of control is key to ensuring that a system is complete and timing constraints are addressed. The existence of multiple threads of control in a system necessitates a partitioning of the system into processes. This paper describes the application and representation of end-to-end threads of control to the object-oriented analysis and design process using object-oriented constructs. The issue of representation is viewed as a grouping problem, that is, how to group classes/objects at a higher level of abstraction so that the system may be viewed as a whole with both classes/objects and their associated dynamic behavior. Existing object-oriented development methodology techniques are extended by adding design-level constructs termed logical composite classes and process composite classes. Logical composite classes are design-level classes which group classes/objects both logically and by thread of control information. Process composite classes further refine the logical composite class groupings by using process partitioning criteria to produce optimum concurrent execution results. The goal of these design-level constructs is to ultimately provide the basis for a mechanism that can support the creation of process composite classes in an automated way. Using an automated mechanism makes it easier to partition a system into concurrently executing elements that can be run in parallel on multiple processors.

Survey Available Computer Software for Automated Production Planning and Inventory Control, and Software and Hardware for Data Logging and Monitoring Shop Floor Activities

DTIC Science & Technology

1993-08-01

pricing and sales, order processing , and purchasing. The class of manufacturing planning functions include aggregate production planning, materials...level. I Depending on the application, each control level will have a number of functions associated with it. For instance, order processing , purchasing...include accounting, sales forecasting, product costing, pricing and sales, order processing , and purchasing. The class of manufacturing planning functions

A Competency Model for Process Dynamics and Control and Its Use for Test Construction at University Level

ERIC Educational Resources Information Center

Taskinen, Päivi H.; Steimel, Jochen; Gräfe, Linda; Engell, Sebastian; Frey, Andreas

2015-01-01

This study examined students' competencies in engineering education at the university level. First, we developed a competency model in one specific field of engineering: process dynamics and control. Then, the theoretical model was used as a frame to construct test items to measure students' competencies comprehensively. In the empirical…

Theory of Mind and Executive Control Deficits in Typically Developing Adults and Adolescents with High Levels of Autism Traits

ERIC Educational Resources Information Center

Gökçen, Elif; Frederickson, Norah; Petrides, K. V.

2016-01-01

Autism spectrum disorder (ASD) is characterised by profound difficulties in empathic processing and executive control. Whilst the links between these processes have been frequently investigated in populations with autism, few studies have examined them at the subclinical level. In addition, the contribution of alexithymia, a trait characterised by…

An fMRI study into emotional processing in Parkinson's disease: Does increased medial prefrontal activation compensate for striatal dysfunction?

PubMed

Moonen, Anja J H; Weiss, Peter H; Wiesing, Michael; Weidner, Ralph; Fink, Gereon R; Reijnders, Jennifer S A M; Weber, Wim M; Leentjens, Albert F G

2017-01-01

Apart from a progressive decline of motor functions, Parkinson's disease (PD) is also characterized by non-motor symptoms, including disturbed processing of emotions. This study aims at assessing emotional processing and its neurobiological correlates in PD with the focus on how medicated Parkinson patients may achieve normal emotional responsiveness despite basal ganglia dysfunction. Nineteen medicated patients with mild to moderate PD (without dementia or depression) and 19 matched healthy controls passively viewed positive, negative, and neutral pictures in an event-related blood oxygen level-dependent functional magnetic resonance imaging study (BOLD-fMRI). Individual subjective ratings of valence and arousal levels for these pictures were obtained right after the scanning. Parkinson patients showed similar valence and arousal ratings as controls, denoting intact emotional processing at the behavioral level. Yet, Parkinson patients showed decreased bilateral putaminal activation and increased activation in the right dorsomedial prefrontal cortex (PFC), compared to controls, both most pronounced for highly arousing emotional stimuli. Our findings revealed for the first time a possible compensatory neural mechanism in Parkinson patients during emotional processing. The increased medial PFC activity may have modulated emotional responsiveness in patients via top-down cognitive control, therewith restoring emotional processing at the behavioral level, despite striatal dysfunction. These results may impact upon current treatment strategies of affective disorders in PD as patients may benefit from this intact or even compensatory influence of prefrontal areas when therapeutic strategies are applied that rely on cognitive control to modulate disturbed processing of emotions.

Measurement science and manufacturing science research

NASA Technical Reports Server (NTRS)

Phillips, D. Howard

1987-01-01

The research program of Semiconductor Research Corp. is managed as three overlapping areas: Manufacturing Sciences, Design Sciences and Microstructure Sciences. A total of 40 universities are participating in the performance of over 200 research tasks. The goals and direction of Manufacturing Sciences research became more clearly focused through the efforts of the Manufacturing Sciences Committee of the SRC Technical Advisory Board (TAB). The mission of the SRC Manufacturing Research is the quantification, control, and understanding of semiconductor manufacturing process necessary to achieve a predictable and profitable product output in the competitive environment of the next decade. The 1994 integrated circuit factory must demonstrate a three level hierarchy of control: (1) operation control, (2) process control, and (3) process design. These levels of control are briefly discussed.

Operating systems. [of computers

NASA Technical Reports Server (NTRS)

Denning, P. J.; Brown, R. L.

1984-01-01

A counter operating system creates a hierarchy of levels of abstraction, so that at a given level all details concerning lower levels can be ignored. This hierarchical structure separates functions according to their complexity, characteristic time scale, and level of abstraction. The lowest levels include the system's hardware; concepts associated explicitly with the coordination of multiple tasks appear at intermediate levels, which conduct 'primitive processes'. Software semaphore is the mechanism controlling primitive processes that must be synchronized. At higher levels lie, in rising order, the access to the secondary storage devices of a particular machine, a 'virtual memory' scheme for managing the main and secondary memories, communication between processes by way of a mechanism called a 'pipe', access to external input and output devices, and a hierarchy of directories cataloguing the hardware and software objects to which access must be controlled.

Aversive emotional interference impacts behavior and prefronto-striatal activity during increasing attentional control.

PubMed

Papazacharias, Apostolos; Taurisano, Paolo; Fazio, Leonardo; Gelao, Barbara; Di Giorgio, Annabella; Lo Bianco, Luciana; Quarto, Tiziana; Mancini, Marina; Porcelli, Annamaria; Romano, Raffaella; Caforio, Grazia; Todarello, Orlando; Popolizio, Teresa; Blasi, Giuseppe; Bertolino, Alessandro

2015-01-01

Earlier studies have demonstrated that emotional stimulation modulates attentional processing during goal-directed behavior and related activity of a brain network including the inferior frontal gyrus (IFG) and the caudate nucleus. However, it is not clear how emotional interference modulates behavior and brain physiology during variation in attentional control, a relevant question for everyday life situations in which both emotional stimuli and cognitive load vary. The aim of this study was to investigate the impact of negative emotions on behavior and activity in IFG and caudate nucleus during increasing levels of attentional control. Twenty two healthy subjects underwent event-related functional magnetic resonance imaging while performing a task in which neutral or fearful facial expressions were displayed before stimuli eliciting increasing levels of attentional control processing. Results indicated slower reaction time (RT) and greater right IFG activity when fearful compared with neutral facial expressions preceded the low level of attentional control. On the other hand, fearful facial expressions preceding the intermediate level of attentional control elicited faster behavioral responses and greater activity in the right and left sides of the caudate. Finally, correlation analysis indicated a relationship between behavioral correlates of attentional control after emotional interference and right IFG activity. All together, these results suggest that the impact of negative emotions on attentional processing is differentially elicited at the behavioral and physiological levels as a function of cognitive load.

Aversive emotional interference impacts behavior and prefronto-striatal activity during increasing attentional control

PubMed Central

Papazacharias, Apostolos; Taurisano, Paolo; Fazio, Leonardo; Gelao, Barbara; Di Giorgio, Annabella; Lo Bianco, Luciana; Quarto, Tiziana; Mancini, Marina; Porcelli, Annamaria; Romano, Raffaella; Caforio, Grazia; Todarello, Orlando; Popolizio, Teresa; Blasi, Giuseppe; Bertolino, Alessandro

2015-01-01

Earlier studies have demonstrated that emotional stimulation modulates attentional processing during goal-directed behavior and related activity of a brain network including the inferior frontal gyrus (IFG) and the caudate nucleus. However, it is not clear how emotional interference modulates behavior and brain physiology during variation in attentional control, a relevant question for everyday life situations in which both emotional stimuli and cognitive load vary. The aim of this study was to investigate the impact of negative emotions on behavior and activity in IFG and caudate nucleus during increasing levels of attentional control. Twenty two healthy subjects underwent event-related functional magnetic resonance imaging while performing a task in which neutral or fearful facial expressions were displayed before stimuli eliciting increasing levels of attentional control processing. Results indicated slower reaction time (RT) and greater right IFG activity when fearful compared with neutral facial expressions preceded the low level of attentional control. On the other hand, fearful facial expressions preceding the intermediate level of attentional control elicited faster behavioral responses and greater activity in the right and left sides of the caudate. Finally, correlation analysis indicated a relationship between behavioral correlates of attentional control after emotional interference and right IFG activity. All together, these results suggest that the impact of negative emotions on attentional processing is differentially elicited at the behavioral and physiological levels as a function of cognitive load. PMID:25954172

Anxiety, anticipation and contextual information: A test of attentional control theory.

PubMed

Cocks, Adam J; Jackson, Robin C; Bishop, Daniel T; Williams, A Mark

2016-09-01

We tested the assumptions of Attentional Control Theory (ACT) by examining the impact of anxiety on anticipation using a dynamic, time-constrained task. Moreover, we examined the involvement of high- and low-level cognitive processes in anticipation and how their importance may interact with anxiety. Skilled and less-skilled tennis players anticipated the shots of opponents under low- and high-anxiety conditions. Participants viewed three types of video stimuli, each depicting different levels of contextual information. Performance effectiveness (response accuracy) and processing efficiency (response accuracy divided by corresponding mental effort) were measured. Skilled players recorded higher levels of response accuracy and processing efficiency compared to less-skilled counterparts. Processing efficiency significantly decreased under high- compared to low-anxiety conditions. No difference in response accuracy was observed. When reviewing directional errors, anxiety was most detrimental to performance in the condition conveying only contextual information, suggesting that anxiety may have a greater impact on high-level (top-down) cognitive processes, potentially due to a shift in attentional control. Our findings provide partial support for ACT; anxiety elicited greater decrements in processing efficiency than performance effectiveness, possibly due to predominance of the stimulus-driven attentional system.

PLANT - An experimental task for the study of human problem solving in process control. [Production Levels and Network Troubleshooting

NASA Technical Reports Server (NTRS)

Morris, N. M.; Rouse, W. B.; Fath, J. L.

1985-01-01

An experimental tool for the investigation of human problem-solving behavior is introduced. Production Levels and Network Troubleshooting (PLANT) is a computer-based process-control task which may be used to provide opportunities for subjects to control a dynamic system and diagnose, repair, and compensate for system failures. The task is described in detail, and experiments which have been conducted using PLANT are briefly discussed.

Off-Line Quality Control In Integrated Circuit Fabrication Using Experimental Design

NASA Astrophysics Data System (ADS)

Phadke, M. S.; Kackar, R. N.; Speeney, D. V.; Grieco, M. J.

1987-04-01

Off-line quality control is a systematic method of optimizing production processes and product designs. It is widely used in Japan to produce high quality products at low cost. The method was introduced to us by Professor Genichi Taguchi who is a Deming-award winner and a former Director of the Japanese Academy of Quality. In this paper we will i) describe the off-line quality control method, and ii) document our efforts to optimize the process for forming contact windows in 3.5 Aim CMOS circuits fabricated in the Murray Hill Integrated Circuit Design Capability Laboratory. In the fabrication of integrated circuits it is critically important to produce contact windows of size very near the target dimension. Windows which are too small or too large lead to loss of yield. The off-line quality control method has improved both the process quality and productivity. The variance of the window size has been reduced by a factor of four. Also, processing time for window photolithography has been substantially reduced. The key steps of off-line quality control are: i) Identify important manipulatable process factors and their potential working levels. ii) Perform fractional factorial experiments on the process using orthogonal array designs. iii) Analyze the resulting data to determine the optimum operating levels of the factors. Both the process mean and the process variance are considered in this analysis. iv) Conduct an additional experiment to verify that the new factor levels indeed give an improvement.

A case study: application of statistical process control tool for determining process capability and sigma level.

PubMed

Chopra, Vikram; Bairagi, Mukesh; Trivedi, P; Nagar, Mona

2012-01-01

Statistical process control is the application of statistical methods to the measurement and analysis of variation process. Various regulatory authorities such as Validation Guidance for Industry (2011), International Conference on Harmonisation ICH Q10 (2009), the Health Canada guidelines (2009), Health Science Authority, Singapore: Guidance for Product Quality Review (2008), and International Organization for Standardization ISO-9000:2005 provide regulatory support for the application of statistical process control for better process control and understanding. In this study risk assessments, normal probability distributions, control charts, and capability charts are employed for selection of critical quality attributes, determination of normal probability distribution, statistical stability, and capability of production processes, respectively. The objective of this study is to determine tablet production process quality in the form of sigma process capability. By interpreting data and graph trends, forecasting of critical quality attributes, sigma process capability, and stability of process were studied. The overall study contributes to an assessment of process at the sigma level with respect to out-of-specification attributes produced. Finally, the study will point to an area where the application of quality improvement and quality risk assessment principles for achievement of six sigma-capable processes is possible. Statistical process control is the most advantageous tool for determination of the quality of any production process. This tool is new for the pharmaceutical tablet production process. In the case of pharmaceutical tablet production processes, the quality control parameters act as quality assessment parameters. Application of risk assessment provides selection of critical quality attributes among quality control parameters. Sequential application of normality distributions, control charts, and capability analyses provides a valid statistical process control study on process. Interpretation of such a study provides information about stability, process variability, changing of trends, and quantification of process ability against defective production. Comparative evaluation of critical quality attributes by Pareto charts provides the least capable and most variable process that is liable for improvement. Statistical process control thus proves to be an important tool for six sigma-capable process development and continuous quality improvement.

Process Instrumentation. Teacher Edition.

ERIC Educational Resources Information Center

Brown, A. O., III; Fowler, Malcolm

This module provides instructional materials that are designed to help teachers train students in job skills for entry-level jobs as instrumentation technicians. This text addresses the basics of troubleshooting control loops, and the transducers, transmitters, signal conditioners, control valves, and controllers that enable process systems to…

An Introduction to Controller Performance Assessment in Process Control Class through Stiction in Control Valves

ERIC Educational Resources Information Center

Srinivasan, Ranganathan; Rengaswamy, Raghunathan; Harris, Sandra

2007-01-01

In this paper, we discuss a simple liquid level experiment that can be used to teach nonlinear phenomena in process control through stiction in control valves. This experiment can be used to introduce the undergraduate students to the area of Controller Performance Assessment (CPA). The experiment is very easy to set-up and demonstrate. While…

Nonlinear response of the anterior cingulate and prefrontal cortex in schizophrenia as a function of variable attentional control.

PubMed

Blasi, Giuseppe; Taurisano, Paolo; Papazacharias, Apostolos; Caforio, Grazia; Romano, Raffaella; Lobianco, Luciana; Fazio, Leonardo; Di Giorgio, Annabella; Latorre, Valeria; Sambataro, Fabio; Popolizio, Teresa; Nardini, Marcello; Mattay, Venkata S; Weinberger, Daniel R; Bertolino, Alessandro

2010-04-01

Previous studies have reported abnormal prefrontal and cingulate activity during attentional control processing in schizophrenia. However, it is not clear how variation in attentional control load modulates activity within these brain regions in this brain disorder. The aim of this study in schizophrenia is to investigate the impact of increasing levels of attentional control processing on prefrontal and cingulate activity. Blood oxygen level-dependent (BOLD) responses of 16 outpatients with schizophrenia were compared with those of 21 healthy subjects while performing a task eliciting increasing levels of attentional control during event-related functional magnetic resonance imaging at 3 T. Results showed reduced behavioral performance in patients at greater attentional control levels. Imaging data indicated greater prefrontal activity at intermediate attentional control levels in patients but greater prefrontal and cingulate responses at high attentional control demands in controls. The BOLD activity profile of these regions in controls increased linearly with increasing cognitive loads, whereas in patients, it was nonlinear. Correlation analysis consistently showed differential region and load-specific relationships between brain activity and behavior in the 2 groups. These results indicate that varying attentional control load is associated in schizophrenia with load- and region-specific modification of the relationship between behavior and brain activity, possibly suggesting earlier saturation of cognitive capacity.

Computational approaches to vision

NASA Technical Reports Server (NTRS)

Barrow, H. G.; Tenenbaum, J. M.

1986-01-01

Vision is examined in terms of a computational process, and the competence, structure, and control of computer vision systems are analyzed. Theoretical and experimental data on the formation of a computer vision system are discussed. Consideration is given to early vision, the recovery of intrinsic surface characteristics, higher levels of interpretation, and system integration and control. A computational visual processing model is proposed and its architecture and operation are described. Examples of state-of-the-art vision systems, which include some of the levels of representation and processing mechanisms, are presented.

Aging of theory of mind: the influence of educational level and cognitive processing.

PubMed

Li, Xiaoming; Wang, Kai; Wang, Fan; Tao, Qian; Xie, Yu; Cheng, Qi

2013-01-01

Previous studies of theory of mind (ToM) in old age have provided mixed results. We predicted that educational level and cognitive processing are two factors influencing the pattern of the aging of ToM. To test this hypothesis, a younger group who received higher education (mean age 20.46 years), an older group with an education level equal to that of the young group (mean age 76.29 years), and an older group with less education (mean age 73.52 years) were recruited. ToM tasks included the following tests: the second-order false-belief task, the faux-pas task, the eyes test, and tests of fundamental aspects of cognitive function that included two background tests (memory span and processing speed) and three subcomponents of executive function (inhibition, updating, and shifting). We found that the younger group and the older group with equally high education outperformed the older group with less education in false-belief and faux-pas tasks. However, there was no significant difference between the two former groups. The three groups of participants performed equivalently in the eyes test as well as in control tasks (false-belief control question, faux-pas control question, faux-pas control story, and Eyes Test control task). The younger group outperformed the other two groups in the cognitive processing tasks. Mediation analyses showed that difficulties in inhibition, memory span, and processing speed mediated the age differences in false-belief reasoning. Also, the variables of inhibition, updating, memory span, and processing speed mediated age-related variance in faux-pas. Discussion focused on the links between ToM aging, educational level, and cognitive processing. Supported by Chinese National Natural Science Foundation (number: 30870766) and Anhui Province Natural Science Foundation (number: 11040606M166).

Improving overlay control through proper use of multilevel query APC

NASA Astrophysics Data System (ADS)

Conway, Timothy H.; Carlson, Alan; Crow, David A.

2003-06-01

Many state-of-the-art fabs are operating with increasingly diversified product mixes. For example, at Cypress Semiconductor, it is not unusual to be concurrently running multiple technologies and many devices within each technology. This diverse product mix significantly increases the difficulty of manually controlling overlay process corrections. As a result, automated run-to-run feedforward-feedback control has become a necessary and vital component of manufacturing. However, traditional run-to-run controllers rely on highly correlated historical events to forecast process corrections. For example, the historical process events typically are constrained to match the current event for exposure tool, device, process level and reticle ID. This narrowly defined process stream can result in insufficient data when applied to lowvolume or new-release devices. The run-to-run controller implemented at Cypress utilizes a multi-level query (Level-N) correlation algorithm, where each subsequent level widens the search criteria for available historical data. The paper discusses how best to widen the search criteria and how to determine and apply a known bias to account for tool-to-tool and device-to-device differences. Specific applications include offloading lots from one tool to another when the first tool is down for preventive maintenance, utilizing related devices to determine a default feedback vector for new-release devices, and applying bias values to account for known reticle-to-reticle differences. In this study, we will show how historical data can be leveraged from related devices or tools to overcome the limitations of narrow process streams. In particular, this paper discusses how effectively handling narrow process streams allows Cypress to offload lots from a baseline tool to an alternate tool.

Levels of steering control: Reproduction of steering-wheel movements

NASA Technical Reports Server (NTRS)

Godthelp, H.

1982-01-01

A schematic description of the steering control process is presented. It is shown that this process can be described in terms of levels of control. Level of control will depend on driver's skill in making use of 'clever' strategies which may be related to knowledge about the path to follow (input) and/or the vehicle under control. This knowledge may be referred to as an internal model of a particular task element. Internal information, as derived from these internal models will probably be used together with proprioceptive feedback. It is hypothesized that the efficiency of the higher levels of control will be dependent on the accuracy of both the internal and proprioceptive information. Based on this research philosophy a series of experiments is carried out. Two primary experiments were done in order to analyse subjects' ability to reproduce steering-wheel positions and movements without visual feedback. Steering-wheel angle amplitude, steering force and movement frequency were involved as independent variables.

Feasibility study of using statistical process control to customized quality assurance in proton therapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rah, Jeong-Eun; Oh, Do Hoon; Shin, Dongho

Purpose: To evaluate and improve the reliability of proton quality assurance (QA) processes and, to provide an optimal customized tolerance level using the statistical process control (SPC) methodology. Methods: The authors investigated the consistency check of dose per monitor unit (D/MU) and range in proton beams to see whether it was within the tolerance level of the daily QA process. This study analyzed the difference between the measured and calculated ranges along the central axis to improve the patient-specific QA process in proton beams by using process capability indices. Results: The authors established a customized tolerance level of ±2% formore » D/MU and ±0.5 mm for beam range in the daily proton QA process. In the authors’ analysis of the process capability indices, the patient-specific range measurements were capable of a specification limit of ±2% in clinical plans. Conclusions: SPC methodology is a useful tool for customizing the optimal QA tolerance levels and improving the quality of proton machine maintenance, treatment delivery, and ultimately patient safety.« less

Controlled versus automatic processes: which is dominant to safety? The moderating effect of inhibitory control.

PubMed

Xu, Yaoshan; Li, Yongjuan; Ding, Weidong; Lu, Fan

2014-01-01

This study explores the precursors of employees' safety behaviors based on a dual-process model, which suggests that human behaviors are determined by both controlled and automatic cognitive processes. Employees' responses to a self-reported survey on safety attitudes capture their controlled cognitive process, while the automatic association concerning safety measured by an Implicit Association Test (IAT) reflects employees' automatic cognitive processes about safety. In addition, this study investigates the moderating effects of inhibition on the relationship between self-reported safety attitude and safety behavior, and that between automatic associations towards safety and safety behavior. The results suggest significant main effects of self-reported safety attitude and automatic association on safety behaviors. Further, the interaction between self-reported safety attitude and inhibition and that between automatic association and inhibition each predict unique variances in safety behavior. Specifically, the safety behaviors of employees with lower level of inhibitory control are influenced more by automatic association, whereas those of employees with higher level of inhibitory control are guided more by self-reported safety attitudes. These results suggest that safety behavior is the joint outcome of both controlled and automatic cognitive processes, and the relative importance of these cognitive processes depends on employees' individual differences in inhibitory control. The implications of these findings for theoretical and practical issues are discussed at the end.

Controlled versus Automatic Processes: Which Is Dominant to Safety? The Moderating Effect of Inhibitory Control

PubMed Central

Xu, Yaoshan; Li, Yongjuan; Ding, Weidong; Lu, Fan

2014-01-01

This study explores the precursors of employees' safety behaviors based on a dual-process model, which suggests that human behaviors are determined by both controlled and automatic cognitive processes. Employees' responses to a self-reported survey on safety attitudes capture their controlled cognitive process, while the automatic association concerning safety measured by an Implicit Association Test (IAT) reflects employees' automatic cognitive processes about safety. In addition, this study investigates the moderating effects of inhibition on the relationship between self-reported safety attitude and safety behavior, and that between automatic associations towards safety and safety behavior. The results suggest significant main effects of self-reported safety attitude and automatic association on safety behaviors. Further, the interaction between self-reported safety attitude and inhibition and that between automatic association and inhibition each predict unique variances in safety behavior. Specifically, the safety behaviors of employees with lower level of inhibitory control are influenced more by automatic association, whereas those of employees with higher level of inhibitory control are guided more by self-reported safety attitudes. These results suggest that safety behavior is the joint outcome of both controlled and automatic cognitive processes, and the relative importance of these cognitive processes depends on employees' individual differences in inhibitory control. The implications of these findings for theoretical and practical issues are discussed at the end. PMID:24520338

Influence of glycemic control on some real-time biomarkers of free radical formation in type 2 diabetic patients: An EPR study.

PubMed

Gadjeva, Veselina Georgieva; Goycheva, Petia; Nikolova, Galina; Zheleva, Antoaneta

2017-11-01

The pathology of diabetes is associated with several mechanisms, one of which is oxidative stress (OS). The relationship between OS and diabetic complications has been extensively investigated. OS has been suggested to be involved in the genesis of both macroand microangiopathy. In contrast, the relationship between OS and insulin action is a neglected research area. The aim of this study is to elucidate the effect of glycemic control in type 2 diabetic patients by following the serum levels of some real-time oxidative stress biomarkers. The study group consisted of 53 type 2 diabetic patients (31 with poor glycemic control and 22 with good glycemic control) and 24 healthy control subjects. The oxidative stress biomarkers (ROS, Asc• and •NO) were measured by using electron paramagnetic resonance spectroscopy (EPR) methods and compared with clinical parameters. The statistically significantly higher levels of ROS products and •NO in type 2 diabetic patients in both groups compared to controls mean that the oxidation processes take place at the time the survey is performed. Free radical overproduction persists after the normalization of the glucose levels, and oxidative stress may be involved in the "metabolic memory" effect. This is confirmed by the positive correlation between ROS levels/•NO and average blood glucose levels, triglycerides, and total cholesterol. Furthermore, the low level of the ascorbate radical in both diabetes groups compared to controls confirmed an increase in oxidation processes. Higher levels of real-time biomarkers show that intensive insulin treatment does not lead to the expected decrease in oxidative processes involving ROS and •NO, probably due to "metabolic memory".

EXPLORING ENGINEERING CONTROL THROUGH PROCESS MANIPULATION OF RADIOACTIVE LIQUID WASTE TANK CHEMICAL CLEANING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, A.

2014-04-27

One method of remediating legacy liquid radioactive waste produced during the cold war, is aggressive in-tank chemical cleaning. Chemical cleaning has successfully reduced the curie content of residual waste heels in large underground storage tanks; however this process generates significant chemical hazards. Mercury is often the bounding hazard due to its extensive use in the separations process that produced the waste. This paper explores how variations in controllable process factors, tank level and temperature, may be manipulated to reduce the hazard potential related to mercury vapor generation. When compared using a multivariate regression analysis, findings indicated that there was amore » significant relationship between both tank level (p value of 1.65x10{sup -23}) and temperature (p value of 6.39x10{sup -6}) to the mercury vapor concentration in the tank ventilation system. Tank temperature showed the most promise as a controllable parameter for future tank cleaning endeavors. Despite statistically significant relationships, there may not be confidence in the ability to control accident scenarios to below mercury’s IDLH or PAC-III levels for future cleaning initiatives.« less

Behavioral inhibition and anxiety: The moderating roles of inhibitory control and attention shifting

PubMed Central

White, Lauren K.; McDermott, Jennifer Martin; Degnan, Kathryn A.; Henderson, Heather A.; Fox, Nathan A.

2013-01-01

Behavioral inhibition (BI), a temperament identified in early childhood, is associated with social reticence in childhood and an increased risk for anxiety problems in adolescence and adulthood. However, not all behaviorally inhibited children remain reticent or develop an anxiety disorder. One possible mechanism accounting for the variability in the developmental trajectories of BI is a child’s ability to successfully recruit cognitive processes involved in the regulation of negative reactivity. However, separate cognitive processes may differentially moderate the association between BI and later anxiety problems. The goal of the current study was to examine how two cognitive processes - attention shifting and inhibitory control - laboratory assessed at 48 months of age moderated the association between 24-month BI and anxiety symptoms in the preschool years. Results revealed that high levels of attention shifting decreased the risk for anxiety symptoms in children with high levels of BI, whereas high levels of inhibitory control increased this risk for anxiety symptoms. These findings suggest that different cognitive processes may influence relative levels of risk or adaptation depending upon a child’s temperamental reactivity. PMID:21301953

Behavioral inhibition and anxiety: the moderating roles of inhibitory control and attention shifting.

PubMed

White, Lauren K; McDermott, Jennifer Martin; Degnan, Kathryn A; Henderson, Heather A; Fox, Nathan A

2011-07-01

Behavioral inhibition (BI), a temperament identified in early childhood, is associated with social reticence in childhood and an increased risk for anxiety problems in adolescence and adulthood. However, not all behaviorally inhibited children remain reticent or develop an anxiety disorder. One possible mechanism accounting for the variability in the developmental trajectories of BI is a child's ability to successfully recruit cognitive processes involved in the regulation of negative reactivity. However, separate cognitive processes may differentially moderate the association between BI and later anxiety problems. The goal of the current study was to examine how two cognitive processes-attention shifting and inhibitory control-laboratory assessed at 48 months of age moderated the association between 24-month BI and anxiety symptoms in the preschool years. Results revealed that high levels of attention shifting decreased the risk for anxiety problems in children with high levels of BI, whereas high levels of inhibitory control increased this risk for anxiety symptoms. These findings suggest that different cognitive processes may influence relative levels of risk or adaptation depending upon a child's temperamental reactivity.

The effect of upper gastrointestinal system endoscopy process on serum oxidative stress levels.

PubMed

Turan, Mehmet Nuri; Aslan, Mehmet; Bolukbas, Filiz Fusun; Bolukbas, Cengiz; Selek, Sahbettin; Sabuncu, Tevfik

2016-12-01

Some authors have investigated the effects of oxidative stress in some process such as undergoing laparoscopic. However, the effect of upper gastrointestinal system endoscopy process on oxidative stress is unclear. We evaluated the short-term effect of upper gastrointestinal system endoscopy process on oxidative stress. Thirty patients who underwent endoscopy process and 20 healthy controls were enrolled in the prospective study. Serum total antioxidant capacity and total oxidant status measurements were measured before and after endoscopy process. The ratio percentage of total oxidant status to total antioxidant capacity was regarded as oxidative stress index. Before endoscopy process, serum total antioxidant capacity levels were higher, while serum total oxidant status levels and oxidative stress index values were lower in patients than controls, but this difference was not statistically significant (all, p > 0.05). After endoscopy process, serum total antioxidant capacity and total oxidant status levels were significantly higher in patients than before endoscopy process (both, p < 0.05). However, oxidative stress index values were slight higher in patients but this difference was not statistically significant (p > 0.05). We observed that serum TAC and TOS levels were increased in patients who underwent endoscopy process after endoscopy process. However, short-time upper gastrointestinal system endoscopy process did not cause an important change in the oxidative stress index. Further studies enrolling a larger number of patients are required to clarify the results obtained here.

Process control systems at Homer City coal preparation plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shell, W.P.

1983-03-01

An important part of process control engineering is the implementation of the basic control system design through commissioning to routine operation. This is a period when basic concepts can be reviewed and improvements either implemented or recorded for application in future systems. The experience of commissioning the process control systems in the Homer City coal cleaning plant are described and discussed. The current level of operating control performance in individual sections and the overall system are also reported and discussed.

Attention - Control in the Frequentistic Processing of Multidimensional Event Streams.

DTIC Science & Technology

1980-07-01

Human memory. Annual Review of Psychology, 1979, 30, 63-702. Craik , F. I. M., & Lockhart , R. S. Levels of processing : A framework for memory research...1979; Jacoby & Craik , 1979). Thus, the notions of memora- bility (or retrievability) and levels of processing are tied closely in the sense that the...differing levels and degrees of elaborateness (Jacoby & Craik , 1979). Decisions as to which attributes receive elaborated processing and how they are

Wafer-level vacuum/hermetic packaging technologies for MEMS

NASA Astrophysics Data System (ADS)

Lee, Sang-Hyun; Mitchell, Jay; Welch, Warren; Lee, Sangwoo; Najafi, Khalil

2010-02-01

An overview of wafer-level packaging technologies developed at the University of Michigan is presented. Two sets of packaging technologies are discussed: (i) a low temperature wafer-level packaging processes for vacuum/hermeticity sealing, and (ii) an environmentally resistant packaging (ERP) technology for thermal and mechanical control as well as vacuum packaging. The low temperature wafer-level encapsulation processes are implemented using solder bond rings which are first patterned on a cap wafer and then mated with a device wafer in order to encircle and encapsulate the device at temperatures ranging from 200 to 390 °C. Vacuum levels below 10 mTorr were achieved with yields in an optimized process of better than 90%. Pressures were monitored for more than 4 years yielding important information on reliability and process control. The ERP adopts an environment isolation platform in the packaging substrate. The isolation platform is designed to provide low power oven-control, vibration isolation and shock protection. It involves batch flip-chip assembly of a MEMS device onto the isolation platform wafer. The MEMS device and isolation structure are encapsulated at the wafer-level by another substrate with vertical feedthroughs for vacuum/hermetic sealing and electrical signal connections. This technology was developed for high performance gyroscopes, but can be applied to any type of MEMS device.

Requirements for implementing real-time control functional modules on a hierarchical parallel pipelined system

NASA Technical Reports Server (NTRS)

Wheatley, Thomas E.; Michaloski, John L.; Lumia, Ronald

1989-01-01

Analysis of a robot control system leads to a broad range of processing requirements. One fundamental requirement of a robot control system is the necessity of a microcomputer system in order to provide sufficient processing capability.The use of multiple processors in a parallel architecture is beneficial for a number of reasons, including better cost performance, modular growth, increased reliability through replication, and flexibility for testing alternate control strategies via different partitioning. A survey of the progression from low level control synchronizing primitives to higher level communication tools is presented. The system communication and control mechanisms of existing robot control systems are compared to the hierarchical control model. The impact of this design methodology on the current robot control systems is explored.

Environmental monitoring of the orbiter payload bay and Orbiter Processing Facilities

NASA Technical Reports Server (NTRS)

Bartelson, D. W.; Johnson, A. M.

1985-01-01

Contamination control in the Orbiter Processing Facility (OPF) is studied. The clean level required in the OPF is generally clean, which means no residue, dirt, debris, or other extraneous contamination; various methods of maintaining this level of cleanliness are described. The monitoring and controlling of the temperature, relative humidity, and air quality in the OPF are examined. Additional modifications to the OPF to improve contamination control are discussed. The methods used to maintain the payload changeout room at a level of visually clean, no particulates are to be detected by the unaided eye, are described. The payload bay (PLB) must sustain the cleanliness level required for the specific Orbiter's mission; the three levels of clean are defined as: (1) standard, (2) sensitive, and (3) high sensitive. The cleaning and inspection verification required to achieve the desired cleanliness level on a variety of PLB surface types are examined.

Product/Process (P/P) Models For The Defense Waste Processing Facility (DWPF): Model Ranges And Validation Ranges For Future Processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jantzen, C.; Edwards, T.

Radioactive high level waste (HLW) at the Savannah River Site (SRS) has successfully been vitrified into borosilicate glass in the Defense Waste Processing Facility (DWPF) since 1996. Vitrification requires stringent product/process (P/P) constraints since the glass cannot be reworked once it is poured into ten foot tall by two foot diameter canisters. A unique “feed forward” statistical process control (SPC) was developed for this control rather than statistical quality control (SQC). In SPC, the feed composition to the DWPF melter is controlled prior to vitrification. In SQC, the glass product would be sampled after it is vitrified. Individual glass property-compositionmore » models form the basis for the “feed forward” SPC. The models transform constraints on the melt and glass properties into constraints on the feed composition going to the melter in order to guarantee, at the 95% confidence level, that the feed will be processable and that the durability of the resulting waste form will be acceptable to a geologic repository.« less

Beyond Auditory Sensory Processing Deficits: Lexical Tone Perception Deficits in Chinese Children With Developmental Dyslexia.

PubMed

Tong, Xiuhong; Tong, Xiuli; King Yiu, Fung

Increasing evidence suggests that children with developmental dyslexia exhibit a deficit not only at the segmental level of phonological processing but also, by extension, at the suprasegmental level. However, it remains unclear whether such a suprasegmental phonological processing deficit is due to a difficulty in processing acoustic cues of speech rhythm, such as rise time and intensity. This study set out to investigate to what extent suprasegmental phonological processing (i.e., Cantonese lexical tone perception) and rise time sensitivity could distinguish Chinese children with dyslexia from typically developing children. Sixteen children with dyslexia and 44 age-matched controls were administered a Cantonese lexical tone perception task, psychoacoustic tasks, a nonverbal reasoning ability task, and word reading and dictation tasks. Children with dyslexia performed worse than controls on Cantonese lexical tone perception, rise time, and intensity. Furthermore, Cantonese lexical tone perception appeared to be a stable indicator that distinguishes children with dyslexia from controls, even after controlling for basic auditory processing skills. These findings suggest that suprasegmental phonological processing (i.e., lexical tone perception) is a potential factor that accounts for reading difficulty in Chinese.

Endocrine Secretory Reserve and Proinsulin Processing in Recipients of Islet of Langerhans Versus Whole Pancreas Transplants

PubMed Central

Elkhafif, Nabeel M.; Borot, Sophie; Morel, Philippe; Demuylder-Mischler, Sandrine; Giovannoni, Laurianne; Toso, Christian; Bosco, Domenico; Berney, Thierry

2013-01-01

OBJECTIVE β-Cells have demonstrated altered proinsulin processing after islet transplantation. We compare β-cell metabolic responses and proinsulin processing in pancreas and islet transplant recipients with respect to healthy control subjects. RESEARCH DESIGN AND METHODS We studied 15 islet and 32 pancreas transplant recipients. Islet subjects were subdivided into insulin-requiring (IR-ISL, n = 6) and insulin-independent (II-ISL, n = 9) groups. Ten healthy subjects served as control subjects. Subjects were administered an intravenous arginine stimulation test, and insulin, C-peptide, total proinsulin, intact proinsulin, and proinsulin fragment levels were determined from serum samples. Acute insulin response (AIR) and proinsulin processing rates were calculated. RESULTS We found that basal insulin and C-peptide levels were higher in the pancreas group than in all other groups. II-ISL patients had basal insulin and C-peptide levels similar to healthy control subjects. The IR-ISL group had significantly lower AIRs than all other groups. Basal processing rates were higher in the pancreas and II-ISL groups than in healthy control subjects and the IR-ISL group. After arginine stimulation, all groups had elevated processing rates, with the exception of the IR-ISL group. CONCLUSIONS Our data suggest that II-ISL transplant recipients can maintain basal metabolic parameters similar to healthy control subjects at the cost of a higher rate of proinsulin processing. IR-ISL transplant recipients, on the other hand, demonstrate both lower insulin response and lower basal rates of proinsulin processing even after arginine stimulation. PMID:24041681

Enhancement of Efficiency and Reduction of Grid Thickness Variation on Casting Process with Lean Six Sigma Method

NASA Astrophysics Data System (ADS)

Witantyo; Setyawan, David

2018-03-01

In a lead acid battery industry, grid casting is a process that has high defect and thickness variation level. DMAIC (Define-Measure-Analyse-Improve-Control) method and its tools will be used to improve the casting process. In the Define stage, it is used project charter and SIPOC (Supplier Input Process Output Customer) method to map the existent problem. In the Measure stage, it is conducted a data retrieval related to the types of defect and the amount of it, also the grid thickness variation that happened. And then the retrieved data is processed and analyzed by using 5 Why’s and FMEA method. In the Analyze stage, it is conducted a grid observation that experience fragile and crack type of defect by using microscope showing the amount of oxide Pb inclusion in the grid. Analysis that is used in grid casting process shows the difference of temperature that is too high between the metal fluid and mold temperature, also the corking process that doesn’t have standard. The Improve stage is conducted a fixing process which generates the reduction of grid variation thickness level and defect/unit level from 9,184% to 0,492%. In Control stage, it is conducted a new working standard determination and already fixed control process.

A Low Cost Microcomputer System for Process Dynamics and Control Simulations.

ERIC Educational Resources Information Center

Crowl, D. A.; Durisin, M. J.

1983-01-01

Discusses a video simulator microcomputer system used to provide real-time demonstrations to strengthen students' understanding of process dynamics and control. Also discusses hardware/software and simulations developed using the system. The four simulations model various configurations of a process liquid level tank system. (JN)

Statistical Process Control: Going to the Limit for Quality.

ERIC Educational Resources Information Center

Training, 1987

1987-01-01

Defines the concept of statistical process control, a quality control method used especially in manufacturing. Generally, concept users set specific standard levels that must be met. Makes the point that although employees work directly with the method, management is responsible for its success within the plant. (CH)

Sentence Context Affects the Brain Response to Masked Words

ERIC Educational Resources Information Center

Coulson, Seana; Brang, David

2010-01-01

Historically, language researchers have assumed that lexical, or word-level processing is fast and automatic, while slower, more controlled post-lexical processes are sensitive to contextual information from higher levels of linguistic analysis. Here we demonstrate the impact of sentence context on the processing of words not available for…

Social anhedonia, but not positive schizotypy, is associated with poor affective control.

PubMed

Martin, Elizabeth A; Cicero, David C; Kerns, John G

2012-07-01

Emotion researchers have distinguished between automatic versus controlled processing of affective information. One previous study with a small sample size found that extreme levels of social anhedonia (SocAnh) in college students, which predicts future schizophrenia-spectrum disorders, is associated with problems in controlled affective processing on a primed evaluation task. The current study examined whether in a larger college student sample SocAnh but not elevated perceptual aberration/magical ideation (PerMag) was associated with poor controlled affective processing. On the primed evaluation task, primes and targets could be either affectively congruent or incongruent and participants judged the valence of targets. Previous research on this task has found that participants appear to use controlled processing in an attempt to counteract the influence of the prime in evaluating the target. In this study, compared to the PerMag (n = 48) and control groups (n = 338), people with extreme levels of social anhedonia (n = 62) exhibited increased affective interference as they were slower for incongruent than for congruent trials. In contrast, there were no differences between the PerMag and control groups. Overall, these results suggest that SocAnh, but not PerMag, is associated with poor controlled affective processing. PsycINFO Database Record (c) 2012 APA, all rights reserved.

Working memory, situation models, and synesthesia

DOE PAGES

Radvansky, Gabriel A.; Gibson, Bradley S.; McNerney, M. Windy

2013-03-04

Research on language comprehension suggests a strong relationship between working memory span measures and language comprehension. However, there is also evidence that this relationship weakens at higher levels of comprehension, such as the situation model level. The current study explored this relationship by comparing 10 grapheme–color synesthetes who have additional color experiences when they read words that begin with different letters and 48 normal controls on a number of tests of complex working memory capacity and processing at the situation model level. On all tests of working memory capacity, the synesthetes outperformed the controls. Importantly, there was no carryover benefitmore » for the synesthetes for processing at the situation model level. This reinforces the idea that although some aspects of language comprehension are related to working memory span scores, this applies less directly to situation model levels. As a result, this suggests that theories of working memory must take into account this limitation, and the working memory processes that are involved in situation model construction and processing must be derived.« less

Working memory, situation models, and synesthesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Radvansky, Gabriel A.; Gibson, Bradley S.; McNerney, M. Windy

Research on language comprehension suggests a strong relationship between working memory span measures and language comprehension. However, there is also evidence that this relationship weakens at higher levels of comprehension, such as the situation model level. The current study explored this relationship by comparing 10 grapheme–color synesthetes who have additional color experiences when they read words that begin with different letters and 48 normal controls on a number of tests of complex working memory capacity and processing at the situation model level. On all tests of working memory capacity, the synesthetes outperformed the controls. Importantly, there was no carryover benefitmore » for the synesthetes for processing at the situation model level. This reinforces the idea that although some aspects of language comprehension are related to working memory span scores, this applies less directly to situation model levels. As a result, this suggests that theories of working memory must take into account this limitation, and the working memory processes that are involved in situation model construction and processing must be derived.« less

Revealing List-Level Control in the Stroop Task by Uncovering Its Benefits and a Cost

PubMed Central

Bugg, Julie M.; McDaniel, Mark A.; Scullin, Michael K.; Braver, Todd S.

2012-01-01

Interference is reduced in mostly incongruent relative to mostly congruent lists. Classic accounts of this list-wide proportion congruence effect assume that list-level control processes strategically modulate word reading. Contemporary accounts posit that reliance on the word is modulated poststimulus onset by item-specific information (e.g., proportion congruency of the word). To adjudicate between these accounts, we used novel designs featuring neutral trials. In two experiments, we showed that the list-wide proportion congruence effect is accompanied by a change in neutral trial color-naming performance. Because neutral words have no item-specific bias, this pattern can be attributed to list-level control. Additionally, we showed that list-level attenuation of word reading led to a cost to performance on a secondary prospective memory task but only when that task required processing of the irrelevant, neutral word. These findings indicate that the list-wide proportion congruence effect at least partially reflects list-level control and challenge purely item-specific accounts of this effect. PMID:21767049

Developmental Dynamics of Emotion and Cognition Processes in Preschoolers

PubMed Central

Blankson, A. Nayena; O’Brien, Marion; Leerkes, Esther M.; Marcovitch, Stuart; Calkins, Susan D.; Weaver, Jennifer Miner

2012-01-01

Dynamic relations during the preschool years across processes of control and understanding in the domains of emotion and cognition were examined. Participants were 263 children (42% non-white) and their mothers who were seen first when the children were 3 years old and again when they were 4. Results indicated dynamic dependence among the processes studied. Specifically, change in cognitive processes of control and understanding were dependent upon initial levels of the other processes. Changes in emotion control and understanding were not predicted by earlier performance in the other processes. Findings are discussed with regard to the constructs of control and understanding and the developmental interrelations among emotion and cognitive processes. PMID:22925076

Generation of control sequences for a pilot-disassembly system

NASA Astrophysics Data System (ADS)

Seliger, Guenther; Kim, Hyung-Ju; Keil, Thomas

2002-02-01

Closing the product and material cycles has emerged as a paradigm for industry in the 21st century. Disassembly plays a key role in a life cycle economy since it enables the recovery of resources. A partly automated disassembly system should adapt to a large variety of products and different degrees of devaluation. Also the amounts of products to be disassembled can vary strongly. To cope with these demands an approach to generate on-line disassembly control sequences will be presented. In order to react on these demands the technological feasibility is considered within a procedure for the generation of disassembly control sequences. Procedures are designed to find available and technologically feasible disassembly processes. The control system is formed by modularised and parameterised control units in the cell level within the entire control architecture. In the first development stage product and process analyses at the sample product washing machine were executed. Furthermore a generalized disassembly process was defined. Afterwards these processes were structured in primary and secondary functions. In the second stage the disassembly control at the technological level was investigated. Factors were the availability of the disassembly tools and the technological feasibility of the disassembly processes within the disassembly system. Technical alternative disassembly processes are determined as a result of availability of the tools and technological feasibility of processes. The fourth phase was the concept for the generation of the disassembly control sequences. The approach will be proved in a prototypical disassembly system.

Intra-individual variability in information processing speed reflects white matter microstructure in multiple sclerosis.

PubMed

Mazerolle, Erin L; Wojtowicz, Magdalena A; Omisade, Antonina; Fisk, John D

2013-01-01

Slowed information processing speed is commonly reported in persons with multiple sclerosis (MS), and is typically investigated using clinical neuropsychological tests, which provide sensitive indices of mean-level information processing speed. However, recent studies have demonstrated that within-person variability or intra-individual variability (IIV) in information processing speed may be a more sensitive indicator of neurologic status than mean-level performance on clinical tests. We evaluated the neural basis of increased IIV in mildly affected relapsing-remitting MS patients by characterizing the relation between IIV (controlling for mean-level performance) and white matter integrity using diffusion tensor imaging (DTI). Twenty women with relapsing-remitting MS and 20 matched control participants completed the Computerized Test of Information Processing (CTIP), from which both mean response time and IIV were calculated. Other clinical measures of information processing speed were also collected. Relations between IIV on the CTIP and DTI metrics of white matter microstructure were evaluated using tract-based spatial statistics. We observed slower and more variable responses on the CTIP in MS patients relative to controls. Significant relations between white matter microstructure and IIV were observed for MS patients. Increased IIV was associated with reduced integrity in more white matter tracts than was slowed information processing speed as measured by either mean CTIP response time or other neuropsychological test scores. Thus, despite the common use of mean-level performance as an index of cognitive dysfunction in MS, IIV may be more sensitive to the overall burden of white matter disease at the microstructural level. Furthermore, our study highlights the potential value of considering within-person fluctuations, in addition to mean-level performance, for uncovering brain-behavior relationships in neurologic disorders with widespread white matter pathology.

The moderating effect of motivation on health-related decision-making.

PubMed

Berezowska, Aleksandra; Fischer, Arnout R H; Trijp, Hans C M van

2017-06-01

This study identifies how autonomous and controlled motivation moderates the cognitive process that drives the adoption of personalised nutrition services. The cognitive process comprises perceptions of privacy risk, personalisation benefit, and their determinants. Depending on their level of autonomous and controlled motivation, participants (N = 3453) were assigned to one of four motivational orientations, which resulted in a 2 (low/high autonomous motivation) × 2 (low/high controlled motivation) quasi-experimental design. High levels of autonomous motivation strengthened the extent to which: (1) the benefits of engaging with a service determined the outcome of a risk-benefit trade-off; (2) the effectiveness of a service determined benefit perceptions. High levels of controlled motivation influenced the extent to which: (1) the risk of privacy loss determined the outcome of a risk-benefit trade-off; (2) controlling personal information after disclosure and perceiving the disclosed personal information as sensitive determined the risk of potential privacy loss. To encourage the adoption of personalised dietary recommendations, for individuals with high levels of autonomous motivation emphasis should be on benefits and its determinants. For those with high levels of controlled motivation, it is important to focus on risk-related issues such as information sensitivity.

Control of Visually Guided Saccades in Multiple Sclerosis: Disruption to Higher-Order Processes

ERIC Educational Resources Information Center

Fielding, Joanne; Kilpatrick, Trevor; Millist, Lynette; White, Owen

2009-01-01

Ocular motor abnormalities are a common feature of multiple sclerosis (MS), with more salient deficits reflecting tissue damage within brainstem and cerebellar circuits. However, MS may also result in disruption to higher level or cognitive control processes governing eye movement, including attentional processes that enhance the neural processing…

Artificial Intelligence Approach to Support Statistical Quality Control Teaching

ERIC Educational Resources Information Center

Reis, Marcelo Menezes; Paladini, Edson Pacheco; Khator, Suresh; Sommer, Willy Arno

2006-01-01

Statistical quality control--SQC (consisting of Statistical Process Control, Process Capability Studies, Acceptance Sampling and Design of Experiments) is a very important tool to obtain, maintain and improve the Quality level of goods and services produced by an organization. Despite its importance, and the fact that it is taught in technical and…

Revisiting the role of trap-assisted-tunneling process on current-voltage characteristics in tunnel field-effect transistors

NASA Astrophysics Data System (ADS)

Omura, Yasuhisa; Mori, Yoshiaki; Sato, Shingo; Mallik, Abhijit

2018-04-01

This paper discusses the role of trap-assisted-tunneling process in controlling the ON- and OFF-state current levels and its impacts on the current-voltage characteristics of a tunnel field-effect transistor. Significant impacts of high-density traps in the source region are observed that are discussed in detail. With regard to recent studies on isoelectronic traps, it has been discovered that deep level density must be minimized to suppress the OFF-state leakage current, as is well known, whereas shallow levels can be utilized to control the ON-state current level. A possible mechanism is discussed based on simulation results.

When the ends outweigh the means: mood and level of identification in depression.

PubMed

Watkins, Edward R; Moberly, Nicholas J; Moulds, Michelle L

2011-11-01

Research in healthy controls has found that mood influences cognitive processing via level of action identification: happy moods are associated with global and abstract processing; sad moods are associated with local and concrete processing. However, this pattern seems inconsistent with the high level of abstract processing observed in depressed patients, leading Watkins (2008, 2010) to hypothesise that the association between mood and level of goal/action identification is impaired in depression. We tested this hypothesis by measuring level of identification on the Behavioural Identification Form after happy and sad mood inductions in never-depressed controls and currently depressed patients. Participants used increasingly concrete action identifications as they became sadder and less happy, but this effect was moderated by depression status. Consistent with Watkins' (2008) hypothesis, increases in sad mood and decreases in happiness were associated with shifts towards the use of more concrete action identifications in never-depressed individuals, but not in depressed patients. These findings suggest that the putatively adaptive association between mood and level of identification is impaired in major depression.

When the ends outweigh the means: Mood and level of identification in depression

PubMed Central

Watkins, Edward R.; Moberly, Nicholas J.; Moulds, Michelle L.

2011-01-01

Research in healthy controls has found that mood influences cognitive processing via level of action identification: happy moods are associated with global and abstract processing; sad moods are associated with local and concrete processing. However, this pattern seems inconsistent with the high level of abstract processing observed in depressed patients, leading Watkins (2008, 2010) to hypothesise that the association between mood and level of goal/action identification is impaired in depression. We tested this hypothesis by measuring level of identification on the Behavioural Identification Form after happy and sad mood inductions in never-depressed controls and currently depressed patients. Participants used increasingly concrete action identifications as they became sadder and less happy, but this effect was moderated by depression status. Consistent with Watkins' (2008) hypothesis, increases in sad mood and decreases in happiness were associated with shifts towards the use of more concrete action identifications in never-depressed individuals, but not in depressed patients. These findings suggest that the putatively adaptive association between mood and level of identification is impaired in major depression. PMID:22017614

High-autonomy control of space resource processing plants

NASA Technical Reports Server (NTRS)

Schooley, Larry C.; Zeigler, Bernard P.; Cellier, Francois E.; Wang, Fei-Yue

1993-01-01

A highly autonomous intelligent command/control architecture has been developed for planetary surface base industrial process plants and Space Station Freedom experimental facilities. The architecture makes use of a high-level task-oriented mode with supervisory control from one or several remote sites, and integrates advanced network communications concepts and state-of-the-art man/machine interfaces with the most advanced autonomous intelligent control. Attention is given to the full-dynamics model of a Martian oxygen-production plant, event-based/fuzzy-logic process control, and fault management practices.

Method and apparatus for automatic control of a humanoid robot

NASA Technical Reports Server (NTRS)

Abdallah, Muhammad E (Inventor); Platt, Robert (Inventor); Wampler, II, Charles W. (Inventor); Sanders, Adam M (Inventor); Reiland, Matthew J (Inventor)

2013-01-01

A robotic system includes a humanoid robot having a plurality of joints adapted for force control with respect to an object acted upon by the robot, a graphical user interface (GUI) for receiving an input signal from a user, and a controller. The GUI provides the user with intuitive programming access to the controller. The controller controls the joints using an impedance-based control framework, which provides object level, end-effector level, and/or joint space-level control of the robot in response to the input signal. A method for controlling the robotic system includes receiving the input signal via the GUI, e.g., a desired force, and then processing the input signal using a host machine to control the joints via an impedance-based control framework. The framework provides object level, end-effector level, and/or joint space-level control of the robot, and allows for functional-based GUI to simplify implementation of a myriad of operating modes.

Computational neuroanatomy of speech production.

PubMed

Hickok, Gregory

2012-01-05

Speech production has been studied predominantly from within two traditions, psycholinguistics and motor control. These traditions have rarely interacted, and the resulting chasm between these approaches seems to reflect a level of analysis difference: whereas motor control is concerned with lower-level articulatory control, psycholinguistics focuses on higher-level linguistic processing. However, closer examination of both approaches reveals a substantial convergence of ideas. The goal of this article is to integrate psycholinguistic and motor control approaches to speech production. The result of this synthesis is a neuroanatomically grounded, hierarchical state feedback control model of speech production.

Neighborhood Concentrated Disadvantage and Dating Violence among Urban Adolescents: The Mediating Role of Neighborhood Social Processes.

PubMed

Garthe, Rachel C; Gorman-Smith, Deborah; Gregory, Joshua; E Schoeny, Michael

2018-06-01

The link between relationship violence and aspects of neighborhood concentrated disadvantage (e.g., percent of unemployed adults, percent of families below poverty level), has been established. However, the literature examining neighborhood social processes, including informal social control and social cohesion, in relation to adolescent dating violence has shown mixed results with a limited theoretical foundation and methodology. Using a social disorganization theoretical framework, this study examined the mediating role of these neighborhood social processes in the relation between concentrated disadvantage and adolescent dating violence within an urban context. Participants included 605 adult residents in 30 census tracts and 203 adolescents from neighborhoods on the West and South sides of Chicago. Neighborhood-level concentrated disadvantage was measured via Census data, adult residents reported on neighborhood social processes, and youth reported on dating violence. Informal social control was negatively associated with dating violence, and social cohesion was positively associated with dating violence. A multilevel mediation model showed that concentrated disadvantage was related to higher levels of dating violence via lower levels of informal social control. These results extend social disorganization theory to dating violence within an urban context, while also highlighting the important role of neighborhood processes on relationship violence. Implications for research and intervention programming are discussed. © Society for Community Research and Action 2018.

Task-dependent response conflict monitoring and cognitive control in anterior cingulate and dorsolateral prefrontal cortices.

PubMed

Kim, Chobok; Chung, Chongwook; Kim, Jeounghoon

2013-11-06

Previous experience affects our behavior in terms of adjustments. It has been suggested that the conflict monitor-controller system implemented in the prefrontal cortex plays a critical role in such adjustments. Previous studies suggested that there exists multiple conflict monitor-controller systems associated with the level of information (i.e., stimulus and response levels). In this study, we sought to test whether different types of conflicts occur at the same information processing level (i.e., response level) are independently processed. For this purpose, we designed a task paradigm to measure two different types of response conflicts using color-based and location-based conflict stimuli and measured the conflict adaptation effects associated with the two types of conflicts either independently (i.e., single conflict conditions) or simultaneously (i.e., a double-conflict condition). The behavioral results demonstrated that performance on current incongruent trials was faster only when the preceding trial was the same type of response conflict regardless of whether they included a single- or double-conflict. Imaging data also showed that anterior cingulate and dorsolateral prefrontal cortices operate in a task-specific manner. These findings suggest that there may be multiple monitor-controller loops for color-based and location-based conflicts even at the same response level. Importantly, our results suggest that double-conflict processing is qualitatively different from single-conflict processing although double-conflict shares the same sources of conflict with two single-conflict conditions. © 2013 Published by Elsevier B.V.

A global "imaging'' view on systems approaches in immunology.

PubMed

Ludewig, Burkhard; Stein, Jens V; Sharpe, James; Cervantes-Barragan, Luisa; Thiel, Volker; Bocharov, Gennady

2012-12-01

The immune system exhibits an enormous complexity. High throughput methods such as the "-omic'' technologies generate vast amounts of data that facilitate dissection of immunological processes at ever finer resolution. Using high-resolution data-driven systems analysis, causal relationships between complex molecular processes and particular immunological phenotypes can be constructed. However, processes in tissues, organs, and the organism itself (so-called higher level processes) also control and regulate the molecular (lower level) processes. Reverse systems engineering approaches, which focus on the examination of the structure, dynamics and control of the immune system, can help to understand the construction principles of the immune system. Such integrative mechanistic models can properly describe, explain, and predict the behavior of the immune system in health and disease by combining both higher and lower level processes. Moving from molecular and cellular levels to a multiscale systems understanding requires the development of methodologies that integrate data from different biological levels into multiscale mechanistic models. In particular, 3D imaging techniques and 4D modeling of the spatiotemporal dynamics of immune processes within lymphoid tissues are central for such integrative approaches. Both dynamic and global organ imaging technologies will be instrumental in facilitating comprehensive multiscale systems immunology analyses as discussed in this review. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Economic-Oriented Stochastic Optimization in Advanced Process Control of Chemical Processes

PubMed Central

Dobos, László; Király, András; Abonyi, János

2012-01-01

Finding the optimal operating region of chemical processes is an inevitable step toward improving economic performance. Usually the optimal operating region is situated close to process constraints related to product quality or process safety requirements. Higher profit can be realized only by assuring a relatively low frequency of violation of these constraints. A multilevel stochastic optimization framework is proposed to determine the optimal setpoint values of control loops with respect to predetermined risk levels, uncertainties, and costs of violation of process constraints. The proposed framework is realized as direct search-type optimization of Monte-Carlo simulation of the controlled process. The concept is illustrated throughout by a well-known benchmark problem related to the control of a linear dynamical system and the model predictive control of a more complex nonlinear polymerization process. PMID:23213298

Low-level laser therapy (LLLT) reduces inflammatory infiltrate and enhances skeletal muscle repair: Histomorphometric parameters

NASA Astrophysics Data System (ADS)

Paiva-Oliveira, E. L.; Lima, N. C.; Silva, P. H.; Sousa, N. T. A.; Barbosa, F. S.; Orsini, M.; Silva, J. G.

2012-09-01

Low level laser therapy (LLLT) has been suggested as an effective therapeutics in inflammatory processes modulation and tissue repairing. However, there is a lack of studies that analyze the anti-inflammatory effects of the infrared lasers in muscular skeletal injury. The aim of this study was to investigate the effects of low-level laser therapy 904 nm in the repair process of skeletal muscle tissue. Swiss mice were submitted to cryoinjury and divided in test (LLLT-treated) and control groups. Histological sections were stained with hematoxylin-eosin to assess general morphology and inflammatory influx, and Picrossirus to quantify collagen fibers deposition. Our results showed significant reduction in inflammatory infiltrated in irradiated mice after 4 days of treatment compared to control ( p = 0.01). After 8 days, the irradiated group showed high levels at regenerating myofibers with significant statistically differences in relation at control group ( p < 0.01). Collagen deposition was significantly increased in the final stages of regeneration at test group, when compared with control group ( p = 0.05). Our data suggests that LLLT reduces the inflammatory response in the initial stages of injury and accelerates the process of muscular tissue repair.

Processes contributing to resilience of coastal wetlands to sea-level rise

USGS Publications Warehouse

Stagg, Camille L.; Krauss, Ken W.; Cahoon, Donald R.; Cormier, Nicole; Conner, William H.; Swarzenski, Christopher M.

2016-01-01

The objectives of this study were to identify processes that contribute to resilience of coastal wetlands subject to rising sea levels and to determine whether the relative contribution of these processes varies across different wetland community types. We assessed the resilience of wetlands to sea-level rise along a transitional gradient from tidal freshwater forested wetland (TFFW) to marsh by measuring processes controlling wetland elevation. We found that, over 5 years of measurement, TFFWs were resilient, although some marginally, and oligohaline marshes exhibited robust resilience to sea-level rise. We identified fundamental differences in how resilience is maintained across wetland community types, which have important implications for management activities that aim to restore or conserve resilient systems. We showed that the relative importance of surface and subsurface processes in controlling wetland surface elevation change differed between TFFWs and oligohaline marshes. The marshes had significantly higher rates of surface accretion than the TFFWs, and in the marshes, surface accretion was the primary contributor to elevation change. In contrast, elevation change in TFFWs was more heavily influenced by subsurface processes, such as root zone expansion or compaction, which played an important role in determining resilience of TFFWs to rising sea level. When root zone contributions were removed statistically from comparisons between relative sea-level rise and surface elevation change, sites that previously had elevation rate deficits showed a surplus. Therefore, assessments of wetland resilience that do not include subsurface processes will likely misjudge vulnerability to sea-level rise.

Design and application of process control charting methodologies to gamma irradiation practices

NASA Astrophysics Data System (ADS)

Saylor, M. C.; Connaghan, J. P.; Yeadon, S. C.; Herring, C. M.; Jordan, T. M.

2002-12-01

The relationship between the contract irradiation facility and the customer has historically been based upon a "PASS/FAIL" approach with little or no quality metrics used to gage the control of the irradiation process. Application of process control charts, designed in coordination with mathematical simulation of routine radiation processing, can provide a basis for understanding irradiation events. By using tools that simulate the physical rules associated with the irradiation process, end-users can explore process-related boundaries and the effects of process changes. Consequently, the relationship between contractor and customer can evolve based on the derived knowledge. The resulting level of mutual understanding of the irradiation process and its resultant control benefits both the customer and contract operation, and provides necessary assurances to regulators. In this article we examine the complementary nature of theoretical (point kernel) and experimental (dosimetric) process evaluation, and the resulting by-product of improved understanding, communication and control generated through the implementation of effective process control charting strategies.

An Automated Statistical Process Control Study of Inline Mixing Using Spectrophotometric Detection

ERIC Educational Resources Information Center

Dickey, Michael D.; Stewart, Michael D.; Willson, C. Grant

2006-01-01

An experiment is described, which is designed for a junior-level chemical engineering "fundamentals of measurements and data analysis" course, where students are introduced to the concept of statistical process control (SPC) through a simple inline mixing experiment. The students learn how to create and analyze control charts in an effort to…

Contamination control and cleanliness level integrity for the Space Shuttle Orbiter PLB, payloads and facilities at KSC

NASA Technical Reports Server (NTRS)

Bartelson, D.

1984-01-01

The PLB, its cargo, and payload canister must satisfy the cleanliness requirements of visual clean (VC) level 1, 2, 3, or special as stated in NASA document SN-C-0005A. The specific level of cleanliness is chosen by the payload bay customer for their mission. During orbiter turnaround processing at KSC, the payload bay is exposed to the environments of the Orbiter Processing Facility (OPF) and the Payload Changeout Room (PCR). In supportive response to the orbiter payload bay/facility interface, it is necessary that the facility environment be controlled and monitored to protect the cleanliness/environmental integrity of the payload bay and its cargo. Techniques used to meet environmental requirements during orbiter processing are introduced.

The civilizing and sportization of Gaelic football in Ireland: 1884–2009.

PubMed

Connolly, John; Dolan, Paddy

2010-01-01

Over the course of the last 125 years the sport of Gaelic football in Ireland has undergone a sportization and civilizing process as the rules governing the sport became stricter and players developed greater levels of self-control. However, the civilizing of Gaelic football was a particularly fragile and uneven process. The growing social desire to diminish displays of violence was moderated by ambivalence towards violence. Gradually the external social controls on players increased and, greater and more stable levels of internalization occurred reflected by more advanced levels of player self-restraint in the control of violence. At the same time the threshold of shame toward displays of violence advanced. This transformation was shaped by lengthening chains of social interdependencies in Ireland.

Hierarchical Control and Skilled Typing: Evidence for Word-Level Control over the Execution of Individual Keystrokes

ERIC Educational Resources Information Center

Crump, Matthew J. C.; Logan, Gordon D.

2010-01-01

Routine actions are commonly assumed to be controlled by hierarchically organized processes and representations. In the domain of typing theories, word-level information is assumed to activate the constituent keystrokes required to type each letter in a word. We tested this assumption directly using a novel single-letter probe technique. Subjects…

New Process Controls for the Hera Cryogenic Plant

NASA Astrophysics Data System (ADS)

Böckmann, T.; Clausen, M.; Gerke, Chr.; Prüß, K.; Schoeneburg, B.; Urbschat, P.

2010-04-01

The cryogenic plant built for the HERA accelerator at DESY in Hamburg (Germany) is now in operation for more than two decades. The commercial process control system for the cryogenic plant is in operation for the same time period. Ever since the operator stations, the control network and the CPU boards in the process controllers went through several upgrade stages. Only the centralized Input/Output system was kept unchanged. Many components have been running beyond the expected lifetime. The control system for one at the three parts of the cryogenic plant has been replaced recently by a distributed I/O system. The I/O nodes are connected to several Profibus-DP field busses. Profibus provides the infrastructure to attach intelligent sensors and actuators directly to the process controllers which run the open source process control software EPICS. This paper describes the modification process on all levels from cabling through I/O configuration, the process control software up to the operator displays.

Determining robot actions for tasks requiring sensor interaction

NASA Technical Reports Server (NTRS)

Budenske, John; Gini, Maria

1989-01-01

The performance of non-trivial tasks by a mobile robot has been a long term objective of robotic research. One of the major stumbling blocks to this goal is the conversion of the high-level planning goals and commands into the actuator and sensor processing controls. In order for a mobile robot to accomplish a non-trivial task, the task must be described in terms of primitive actions of the robot's actuators. Most non-trivial tasks require the robot to interact with its environment; thus necessitating coordination of sensor processing and actuator control to accomplish the task. The main contention is that the transformation from the high level description of the task to the primitive actions should be performed primarily at execution time, when knowledge about the environment can be obtained through sensors. It is proposed to produce the detailed plan of primitive actions by using a collection of low-level planning components that contain domain specific knowledge and knowledge about the available sensors, actuators, and sensor/actuator processing. This collection will perform signal and control processing as well as serve as a control interface between an actual mobile robot and a high-level planning system. Previous research has shown the usefulness of high-level planning systems to plan the coordination of activities such to achieve a goal, but none have been fully applied to actual mobile robots due to the complexity of interacting with sensors and actuators. This control interface is currently being implemented on a LABMATE mobile robot connected to a SUN workstation and will be developed such to enable the LABMATE to perform non-trivial, sensor-intensive tasks as specified by a planning system.

Encoding and choice in the task span paradigm.

PubMed

Reiman, Kaitlin M; Weaver, Starla M; Arrington, Catherine M

2015-03-01

Cognitive control during sequences of planned behaviors requires both plan-level processes such as generating, maintaining, and monitoring the plan, as well as task-level processes such as selecting, establishing and implementing specific task sets. The task span paradigm (Logan in J Exp Psychol Gen 133:218-236, 2004) combines two common cognitive control paradigms, task switching and working memory span, to investigate the integration of plan-level and task-level processes during control of sequential behavior. The current study expands past task span research to include measures of encoding processes and choice behavior with volitional sequence generation, using the standard task span as well as a novel voluntary task span paradigm. In two experiments, we consider how sequence complexity, defined separately for plan-level and task-level complexity, influences sequence encoding (Experiment 1), sequence choice (Experiment 2), sequence memory, and task performance of planned sequences of action. Results indicate that participants were sensitive to sequence complexity, but that different aspects of behavior are most strongly influenced by different types of complexity. Hierarchical complexity at the plan level best predicts voluntary sequence generation and memory; while switch frequency at the task level best predicts encoding of externally defined sequences and task performance. Furthermore, performance RTs were similar for externally and internally defined plans, whereas memory was improved for internally defined sequences. Finally, participants demonstrated a significant sequence choice bias in the voluntary task span. Consistent with past research on choice behavior, volitional selection of plans was markedly influenced by both the ease of memory and performance.

Sustained Attention in Mild Alzheimer’s Disease

PubMed Central

Berardi, Anna Maria; Parasuraman, Raja; Haxby, James V.

2008-01-01

The vigilance decrement in perceptual sensitivity was examined in 10 patients with mild Alzheimer’s disease (AD) and 20 age-matched controls. A visual high-event rate digit-discrimination task lasting 7.2 min. (six 1.2 min blocks) was presented at different levels of stimulus degradation. Previous studies have shown that sensitivity decrements (d′) over time at high-stimulus degradation result from demands on effortful processing. For all degradation levels, the overall level of vigilance (d′) was lower in AD patients than in controls. All participants showed sensitivity decrement over blocks, with greater decrement at higher degradation levels. AD patients exhibited greater sensitivity decrement over time at the highest degradation level they all could perform relative to control participants. There were no concomitant changes in either response bias (C) or response times. The results indicate that mild AD patients have overall lower levels of vigilance under conditions that require both automatic and effortful processing. Mild AD patients also exhibit a deficit in the maintenance of vigilance over time under effortful processing conditions. Although the sample of AD patients was small, results further suggest that both possible and probable AD patients had greater sensitivity decrement over time at the highest degradation level than did control participants, but only probable AD patients had lower overall levels of vigilance. In the possible AD patients as a group, the decrement in vigilance occurred in the absence of concurrent deficits on standard attentional tasks, such as the Stroop and Trail Making tests, suggesting that deficits in vigilance over time may appear earlier than deficits in selective attention. PMID:15992254

21 CFR 123.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... acceptable levels. (c) Critical limit means the maximum or minimum value to which a physical, biological, or... acceptable level the occurrence of the identified food safety hazard. (d) Fish means fresh or saltwater... used to indicate conditions during processing at a critical control point. (k)(1) Processing means...

Deaf individuals who work with computers present a high level of visual attention.

PubMed

Ribeiro, Paula Vieira; Ribas, Valdenilson Ribeiro; Ribas, Renata de Melo Guerra; de Melo, Teresinha de Jesus Oliveira Guimarães; Marinho, Carlos Antonio de Sá; Silva, Kátia Karina do Monte; de Albuquerque, Elizabete Elias; Ribas, Valéria Ribeiro; de Lima, Renata Mirelly Silva; Santos, Tuthcha Sandrelle Botelho Tavares

2011-01-01

Some studies in the literature indicate that deaf individuals seem to develop a higher level of attention and concentration during the process of constructing of different ways of communicating. The aim of this study was to evaluate the level of attention in individuals deaf from birth that worked with computers. A total of 161 individuals in the 18-25 age group were assessed. Of these, 40 were congenitally deaf individuals that worked with computers, 42 were deaf individuals that did not work, did not know how to use nor used computers (Control 1), 39 individuals with normal hearing that did not work, did not know how to use computers nor used them (Control 2), and 40 individuals with normal hearing that worked with computers (Control 3). The group of subjects deaf from birth that worked with computers (IDWC) presented a higher level of focused attention, sustained attention, mental manipulation capacity and resistance to interference compared to the control groups. This study highlights the relevance sensory to cognitive processing.

Speed-accuracy trade-off in skilled typewriting: decomposing the contributions of hierarchical control loops.

PubMed

Yamaguchi, Motonori; Crump, Matthew J C; Logan, Gordon D

2013-06-01

Typing performance involves hierarchically structured control systems: At the higher level, an outer loop generates a word or a series of words to be typed; at the lower level, an inner loop activates the keystrokes comprising the word in parallel and executes them in the correct order. The present experiments examined contributions of the outer- and inner-loop processes to the control of speed and accuracy in typewriting. Experiments 1 and 2 involved discontinuous typing of single words, and Experiments 3 and 4 involved continuous typing of paragraphs. Across experiments, typists were able to trade speed for accuracy but were unable to type at rates faster than 100 ms/keystroke, implying limits to the flexibility of the underlying processes. The analyses of the component latencies and errors indicated that the majority of the trade-offs were due to inner-loop processing. The contribution of outer-loop processing to the trade-offs was small, but it resulted in large costs in error rate. Implications for strategic control of automatic processes are discussed. (PsycINFO Database Record (c) 2013 APA, all rights reserved).

A generic testbed for the design of plasma spectrometer control software with application to the THOR-CSW solar wind instrument

NASA Astrophysics Data System (ADS)

De Keyser, Johan; Lavraud, Benoit; Neefs, Eddy; Berkenbosch, Sophie; Beeckman, Bram; Maggiolo, Romain; Gamby, Emmanuel; Fedorov, Andrei; Baruah, Rituparna; Wong, King-Wah; Amoros, Carine; Mathon, Romain; Génot, Vincent; Marcucci, Federica; Brienza, Daniele

2017-04-01

Modern plasma spectrometers require intelligent software that is able to exploit their capabilities to the fullest. While the low-level control of the instrument and basic tasks such as performing the basic measurement, temperature control, and production of housekeeping data are to be done by software that is executed on an FPGA and/or processor inside the instrument, higher level tasks such as control of measurement sequences, on-board moment calculation, beam tracking decisions, and data compression, may be performed by the instrument or in the payload data processing unit. Such design decisions, as well as an assessment of the workload on the different processing components, require early prototyping. We have developed a generic simulation testbed for the design of plasma spectrometer control software that allows an early evaluation of the level of resources that is needed at each level. Early prototyping can pinpoint bottlenecks in the design allowing timely remediation. We have applied this tool to the THOR Cold Solar Wind (CSW) plasma spectrometer. Some examples illustrating the usefulness of the tool are given.

The Process of Adaptation of a Community-Level, Evidence-Based Intervention for HIV-Positive African American Men Who Have Sex with Men in Two Cities

ERIC Educational Resources Information Center

Robinson, Beatrice E.; Galbraith, Jennifer S.; Lund, Sharon M.; Hamilton, Autumn R.; Shankle, Michael D.

2012-01-01

We describe the process of adapting a community-level, evidence-based behavioral intervention (EBI), Community PROMISE, for HIV-positive African American men who have sex with men (AAMSM). The Centers for Disease Control and Prevention (CDC) Map of the Adaptation Process (MAP) guided the adaptation process for this new target population by two…

Analytical design of intelligent machines

NASA Technical Reports Server (NTRS)

Saridis, George N.; Valavanis, Kimon P.

1987-01-01

The problem of designing 'intelligent machines' to operate in uncertain environments with minimum supervision or interaction with a human operator is examined. The structure of an 'intelligent machine' is defined to be the structure of a Hierarchically Intelligent Control System, composed of three levels hierarchically ordered according to the principle of 'increasing precision with decreasing intelligence', namely: the organizational level, performing general information processing tasks in association with a long-term memory; the coordination level, dealing with specific information processing tasks with a short-term memory; and the control level, which performs the execution of various tasks through hardware using feedback control methods. The behavior of such a machine may be managed by controls with special considerations and its 'intelligence' is directly related to the derivation of a compatible measure that associates the intelligence of the higher levels with the concept of entropy, which is a sufficient analytic measure that unifies the treatment of all the levels of an 'intelligent machine' as the mathematical problem of finding the right sequence of internal decisions and controls for a system structured in the order of intelligence and inverse order of precision such that it minimizes its total entropy. A case study on the automatic maintenance of a nuclear plant illustrates the proposed approach.

Integrated control system for electron beam processes

NASA Astrophysics Data System (ADS)

Koleva, L.; Koleva, E.; Batchkova, I.; Mladenov, G.

2018-03-01

The ISO/IEC 62264 standard is widely used for integration of the business systems of a manufacturer with the corresponding manufacturing control systems based on hierarchical equipment models, functional data and manufacturing operations activity models. In order to achieve the integration of control systems, formal object communication models must be developed, together with manufacturing operations activity models, which coordinate the integration between different levels of control. In this article, the development of integrated control system for electron beam welding process is presented as part of a fully integrated control system of an electron beam plant, including also other additional processes: surface modification, electron beam evaporation, selective melting and electron beam diagnostics.

Ethylene thiourea: thyroid function in two groups of exposed workers.

PubMed Central

Smith, D M

1984-01-01

Ethylene thiourea is manufactured at one factory in the United Kingdom and is mixed into masterbatch rubber at another. Clinical examinations and thyroid function tests were carried out over a period of three years on eight process workers and five mixers and on matched controls. The results show that the exposed mixers, but not exposed process workers, have significantly lower levels of total thyroxine (T4) than the controls. One mixer had an appreciably raised level of thyroid stimulation hormone (TSH). PMID:6743584

Ethylene thiourea: thyroid function in two groups of exposed workers.

PubMed

Smith, D M

1984-08-01

Ethylene thiourea is manufactured at one factory in the United Kingdom and is mixed into masterbatch rubber at another. Clinical examinations and thyroid function tests were carried out over a period of three years on eight process workers and five mixers and on matched controls. The results show that the exposed mixers, but not exposed process workers, have significantly lower levels of total thyroxine (T4) than the controls. One mixer had an appreciably raised level of thyroid stimulation hormone (TSH).

Minimax terminal approach problem in two-level hierarchical nonlinear discrete-time dynamical system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shorikov, A. F., E-mail: afshorikov@mail.ru

We consider a discrete–time dynamical system consisting of three controllable objects. The motions of all objects are given by the corresponding vector nonlinear or linear discrete–time recurrent vector relations, and control system for its has two levels: basic (first or I level) that is dominating and subordinate level (second or II level) and both have different criterions of functioning and united a priori by determined informational and control connections defined in advance. For the dynamical system in question, we propose a mathematical formalization in the form of solving a multistep problem of two-level hierarchical minimax program control over the terminalmore » approach process with incomplete information and give a general scheme for its solving.« less

Enzymes Involved in Post-transcriptional RNA Metabolism in Gram-negative bacteria

PubMed Central

Mohanty, Bijoy K.

2018-01-01

Gene expression in Gram-negative bacteria is regulated at many levels, including transcription initiation, RNA processing, RNA/RNA interactions, mRNA decay, and translational controls involving enzymes that alter translational efficiency. In this chapter we discuss the various enzymes that control transcription, translation and RNA stability through RNA processing and degradation. RNA processing is essential to generate functional RNAs, while degradation helps control the steady-state level of each individual transcript. For example, all the pre-tRNAs are transcribed with extra nucleotides at both their 5′ and 3′ termini, which are subsequently processed to produce mature tRNAs that can be aminoacylated. Similarly, rRNAs that are transcribed as part of a 30S polycistronic transcript, are matured to individual 16S, 23S and 5S rRNAs. Decay of mRNAs plays a key role in gene regulation through controlling the steady-state level of each transcript, which is essential for maintaining appropriate protein levels. In addition, degradation of both translated and non-translated RNAs recycles nucleotides to facilitate new RNA synthesis. To carry out all these reactions Gram-negative bacteria employ a large number of endonucleases, exonucleases, RNA helicases, and poly(A) polymerase as well as proteins that regulate the catalytic activity of particular ribonucleases. Under certain stress conditions an additional group of specialized endonucleases facilitate the cell’s ability to adapt and survive. Many of the enzymes, such as RNase E, RNase III, polynucleotide phosphorylase, RNase R, and poly(A) polymerase I participate in multiple RNA processing and decay pathways. PMID:29676246

Evaluation of marsh development processes at Fire Island National Seashore: Recent and historic perspectives

USGS Publications Warehouse

Roman, C.T.; King, D.R.; Cahoon, D.R.; Lynch, J.C.; Appleby, P.G.

2007-01-01

Purpose and significance of the study: Salt marshes are dynamic environments, increasing in vertical elevation and migrating, often landward, as sea level rises. With sea level rise greater than marsh elevation increase, marshes can be submerged, marsh soils become waterlogged, and plant growth becomes stressed, often resulting in conversion of vegetation-dominated marsh to mudflat or open water habitat. Given that the rate of sea level rise is expected to accelerate over the next century and that some marshes in the northeast are becoming submerged (e.g., Jamaica Bay, NY), it is important to understand the processes that control marsh development. More specifically, the objectives of this project were to quantify vertical marsh elevation change in relation to recent rates of sea-level rise and to investigate factors or processes that are most influential in controlling the development and maintenance of Fire Island salt marshes.

VPPA weld model evaluation

NASA Technical Reports Server (NTRS)

Mccutcheon, Kimble D.; Gordon, Stephen S.; Thompson, Paul A.

1992-01-01

NASA uses the Variable Polarity Plasma Arc Welding (VPPAW) process extensively for fabrication of Space Shuttle External Tanks. This welding process has been in use at NASA since the late 1970's but the physics of the process have never been satisfactorily modeled and understood. In an attempt to advance the level of understanding of VPPAW, Dr. Arthur C. Nunes, Jr., (NASA) has developed a mathematical model of the process. The work described in this report evaluated and used two versions (level-0 and level-1) of Dr. Nunes' model, and a model derived by the University of Alabama at Huntsville (UAH) from Dr. Nunes' level-1 model. Two series of VPPAW experiments were done, using over 400 different combinations of welding parameters. Observations were made of VPPAW process behavior as a function of specific welding parameter changes. Data from these weld experiments was used to evaluate and suggest improvements to Dr. Nunes' model. Experimental data and correlations with the model were used to develop a multi-variable control algorithm for use with a future VPPAW controller. This algorithm is designed to control weld widths (both on the crown and root of the weld) based upon the weld parameters, base metal properties, and real-time observation of the crown width. The algorithm exhibited accuracy comparable to that of the weld width measurements for both aluminum and mild steel welds.

Unravelling the influence of mild traumatic brain injury (MTBI) on cognitive-linguistic processing: a comparative group analysis.

PubMed

Barwood, Caroline H S; Murdoch, Bruce E

2013-06-01

Cognitive-linguistic deficits often accompany traumatic brain injury (TBI) and can negatively impact communicative competency. The linguistic sequelae underpinning mild TBI (MTBI) remain largely unexplored in contemporary literature. The present research methods aim to provide group evidence pertaining to the influence of MTBI on linguistic and higher-level language processing. Extrapolating on the findings of recent case reports, it is hypothesized that performance of the MTBI patients will be significantly reduced compared to normal controls performance on the employed high-level linguistic tasks. Sixteen patients with MTBI and 16 age- and education-matched normal control participants were assessed using a comprehensive battery of cognitive-linguistic assessments. The results demonstrated statistically significant differences between MTBI and normal control group performance across a number of higher-level linguistic, general cognitive and general language tasks. MTBI group performance was significantly lower than the normal control group on tasks requiring complex lexical semantic operations and memory demands, including: Recall, organization, making inferences, naming and perception/discrimination. These outcomes confer that post-MTBI, cognitive, high-level language and isolated general language performance (e.g. naming) is significantly reduced in MTBI patients, compared to normal controls. Furthermore, the detailed cognitive-linguistic profile offered provides a necessary direction for the identification of areas of linguistic decline in MTBI and targets for therapeutic intervention of impaired cognitive-linguistic processes to ultimately improve communicative outcomes in MTBI.

Contracting Processes, Internal Controls, and Procurement Fraud: A Knowledge Assessment

DTIC Science & Technology

2015-04-30

ååì~ä=^Åèìáëáíáçå= oÉëÉ~êÅÜ=póãéçëáìã= qÜìêëÇ~ó=pÉëëáçåë= sçäìãÉ=ff= = Contracting Processes, Internal Controls, and Procurement Fraud: A Knowledge...DATES COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE Contracting Processes, Internal Controls, and Procurement Fraud: A Knowledge...capable processes, and effective internal controls result in the DoD having a higher level of vulnerability for procurement fraud (Rendon & Rendon, in

Removing Sulphur Dioxide From Stack Gases

ERIC Educational Resources Information Center

Slack, A. V.

1973-01-01

Process types, process concepts, claims and counterclaims, cost factors, and the level of developed technology for sulfur dioxide control in stack gases are focused upon and evaluated. Wet and dry processes as well as recovery and throwaway processes are compared. (BL)

Assessing Subjectivity in Sensor Data Post Processing via a Controlled Experiment

NASA Astrophysics Data System (ADS)

Jones, A. S.; Horsburgh, J. S.; Eiriksson, D.

2017-12-01

Environmental data collected by in situ sensors must be reviewed to verify validity, and conducting quality control often requires making edits in post processing to generate approved datasets. This process involves decisions by technicians, data managers, or data users on how to handle problematic data. Options include: removing data from a series, retaining data with annotations, and altering data based on algorithms related to adjacent data points or the patterns of data at other locations or of other variables. Ideally, given the same dataset and the same quality control guidelines, multiple data quality control technicians would make the same decisions in data post processing. However, despite the development and implementation of guidelines aimed to ensure consistent quality control procedures, we have faced ambiguity when performing post processing, and we have noticed inconsistencies in the practices of individuals performing quality control post processing. Technicians with the same level of training and using the same input datasets may produce different results, affecting the overall quality and comparability of finished data products. Different results may also be produced by technicians that do not have the same level of training. In order to assess the effect of subjective decision making by the individual technician on the end data product, we designed an experiment where multiple users performed quality control post processing on the same datasets using a consistent set of guidelines, field notes, and tools. We also assessed the effect of technician experience and training by conducting the same procedures with a group of novices unfamiliar with the data and the quality control process and compared their results to those generated by a group of more experienced technicians. In this presentation, we report our observations of the degree of subjectivity in sensor data post processing, assessing and quantifying the impacts of individual technician as well as technician experience on quality controlled data products.

Hierarchical Active Inference: A Theory of Motivated Control.

PubMed

Pezzulo, Giovanni; Rigoli, Francesco; Friston, Karl J

2018-04-01

Motivated control refers to the coordination of behaviour to achieve affectively valenced outcomes or goals. The study of motivated control traditionally assumes a distinction between control and motivational processes, which map to distinct (dorsolateral versus ventromedial) brain systems. However, the respective roles and interactions between these processes remain controversial. We offer a novel perspective that casts control and motivational processes as complementary aspects - goal propagation and prioritization, respectively - of active inference and hierarchical goal processing under deep generative models. We propose that the control hierarchy propagates prior preferences or goals, but their precision is informed by the motivational context, inferred at different levels of the motivational hierarchy. The ensuing integration of control and motivational processes underwrites action and policy selection and, ultimately, motivated behaviour, by enabling deep inference to prioritize goals in a context-sensitive way. Copyright © 2018 The Author(s). Published by Elsevier Ltd.. All rights reserved.

Six sigma: process of understanding the control and capability of ranitidine hydrochloride tablet.

PubMed

Chabukswar, Ar; Jagdale, Sc; Kuchekar, Bs; Joshi, Vd; Deshmukh, Gr; Kothawade, Hs; Kuckekar, Ab; Lokhande, Pd

2011-01-01

The process of understanding the control and capability (PUCC) is an iterative closed loop process for continuous improvement. It covers the DMAIC toolkit in its three phases. PUCC is an iterative approach that rotates between the three pillars of the process of understanding, process control, and process capability, with each iteration resulting in a more capable and robust process. It is rightly said that being at the top is a marathon and not a sprint. The objective of the six sigma study of Ranitidine hydrochloride tablets is to achieve perfection in tablet manufacturing by reviewing the present robust manufacturing process, to find out ways to improve and modify the process, which will yield tablets that are defect-free and will give more customer satisfaction. The application of six sigma led to an improved process capability, due to the improved sigma level of the process from 1.5 to 4, a higher yield, due to reduced variation and reduction of thick tablets, reduction in packing line stoppages, reduction in re-work by 50%, a more standardized process, with smooth flow and change in coating suspension reconstitution level (8%w/w), a huge cost reduction of approximately Rs.90 to 95 lakhs per annum, an improved overall efficiency by 30% approximately, and improved overall quality of the product.

Six Sigma: Process of Understanding the Control and Capability of Ranitidine Hydrochloride Tablet

PubMed Central

Chabukswar, AR; Jagdale, SC; Kuchekar, BS; Joshi, VD; Deshmukh, GR; Kothawade, HS; Kuckekar, AB; Lokhande, PD

2011-01-01

The process of understanding the control and capability (PUCC) is an iterative closed loop process for continuous improvement. It covers the DMAIC toolkit in its three phases. PUCC is an iterative approach that rotates between the three pillars of the process of understanding, process control, and process capability, with each iteration resulting in a more capable and robust process. It is rightly said that being at the top is a marathon and not a sprint. The objective of the six sigma study of Ranitidine hydrochloride tablets is to achieve perfection in tablet manufacturing by reviewing the present robust manufacturing process, to find out ways to improve and modify the process, which will yield tablets that are defect-free and will give more customer satisfaction. The application of six sigma led to an improved process capability, due to the improved sigma level of the process from 1.5 to 4, a higher yield, due to reduced variation and reduction of thick tablets, reduction in packing line stoppages, reduction in re-work by 50%, a more standardized process, with smooth flow and change in coating suspension reconstitution level (8%w/w), a huge cost reduction of approximately Rs.90 to 95 lakhs per annum, an improved overall efficiency by 30% approximately, and improved overall quality of the product. PMID:21607050

Fish welfare assurance system: initial steps to set up an effective tool to safeguard and monitor farmed fish welfare at a company level.

PubMed

van de Vis, J W; Poelman, M; Lambooij, E; Bégout, M-L; Pilarczyk, M

2012-02-01

The objective was to take a first step in the development of a process-oriented quality assurance (QA) system for monitoring and safeguarding of fish welfare at a company level. A process-oriented approach is focused on preventing hazards and involves establishment of critical steps in a process that requires careful control. The seven principles of the Hazard Analysis Critical Control Points (HACCP) concept were used as a framework to establish the QA system. HACCP is an internationally agreed approach for management of food safety, which was adapted for the purpose of safeguarding and monitoring the welfare of farmed fish. As the main focus of this QA system is farmed fish welfare assurance at a company level, it was named Fish Welfare Assurance System (FWAS). In this paper we present the initial steps of setting up FWAS for on growing of sea bass (Dicentrarchus labrax), carp (Cyprinus carpio) and European eel (Anguilla anguilla). Four major hazards were selected, which were fish species dependent. Critical Control Points (CCPs) that need to be controlled to minimize or avoid the four hazards are presented. For FWAS, monitoring of CCPs at a farm level is essential. For monitoring purposes, Operational Welfare Indicators (OWIs) are needed to establish whether critical biotic, abiotic, managerial and environmental factors are controlled. For the OWIs we present critical limits/target values. A critical limit is the maximum or minimum value to which a factor must be controlled at a critical control point to prevent, eliminate or reduce a hazard to an acceptable level. For managerial factors target levels are more appropriate than critical limits. Regarding the international trade of farmed fish products, we propose that FWAS needs to be standardized in aquaculture chains. For this standardization a consensus on the concept of fish welfare, methods to assess welfare objectively and knowledge on the needs of farmed fish are required.

42. Upper level, electronic racks, left to rightguidance and control ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

42. Upper level, electronic racks, left to right--guidance and control coupler rack, programmer group, status command message processing group, UHF radio - Ellsworth Air Force Base, Delta Flight, Launch Facility, On County Road T512, south of Exit 116 off I-90, Interior, Jackson County, SD

SNMG: a social-level norm-based methodology for macro-governing service collaboration processes

NASA Astrophysics Data System (ADS)

Gao, Ji; Lv, Hexin; Jin, Zhiyong; Xu, Ping

2017-08-01

In order to adapt to the accelerative open tendency of collaborations between enterprises, this paper proposes a Social-level Norm-based methodology for Macro-Governing service collaboration processes, called SNMG, to regulate and control the social-level visible macro-behaviors of the social individuals participating in collaborations. SNMG not only can remove effectively the uncontrollability hindrance confronted with by open social activities, but also enables across-management-domain collaborations to be implemented by uniting the centralized controls of social individuals for respective social activities. Therefore, this paper provides a brand-new system construction mode to promote the development and large-scale deployment of service collaborations.

SEPAC software configuration control plan and procedures, revision 1

NASA Technical Reports Server (NTRS)

1981-01-01

SEPAC Software Configuration Control Plan and Procedures are presented. The objective of the software configuration control is to establish the process for maintaining configuration control of the SEPAC software beginning with the baselining of SEPAC Flight Software Version 1 and encompass the integration and verification tests through Spacelab Level IV Integration. They are designed to provide a simplified but complete configuration control process. The intent is to require a minimum amount of paperwork but provide total traceability of SEPAC software.

On-Line Real-Time Management Information Systems and Their Impact Upon User Personnel and Organizational Structure in Aviation Maintenance Activities.

DTIC Science & Technology

1979-12-01

the functional management level, a real-time production con- trol system and an order processing system at the operational level. SIDMS was designed...at any one time. 26 An overview of the major software systems in operation is listed below: a. Major Software Systems: Order processing system e Order ... processing for the supply support center/AWP locker. e Order processing for the airwing squadron material controls. e Order processing for the IMA

76 FR 72902 - Materials Processing Equipment Technical Advisory Committee;

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-28

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical... questions that affect the level of export controls applicable to materials processing equipment and related...

Expert system and process optimization techniques for real-time monitoring and control of plasma processes

NASA Astrophysics Data System (ADS)

Cheng, Jie; Qian, Zhaogang; Irani, Keki B.; Etemad, Hossein; Elta, Michael E.

1991-03-01

To meet the ever-increasing demand of the rapidly-growing semiconductor manufacturing industry it is critical to have a comprehensive methodology integrating techniques for process optimization real-time monitoring and adaptive process control. To this end we have accomplished an integrated knowledge-based approach combining latest expert system technology machine learning method and traditional statistical process control (SPC) techniques. This knowledge-based approach is advantageous in that it makes it possible for the task of process optimization and adaptive control to be performed consistently and predictably. Furthermore this approach can be used to construct high-level and qualitative description of processes and thus make the process behavior easy to monitor predict and control. Two software packages RIST (Rule Induction and Statistical Testing) and KARSM (Knowledge Acquisition from Response Surface Methodology) have been developed and incorporated with two commercially available packages G2 (real-time expert system) and ULTRAMAX (a tool for sequential process optimization).

The Impact of Retrieval Processes, Age, General Achievement Level, and Test Scoring Scheme for Children's Metacognitive Monitoring and Controlling

ERIC Educational Resources Information Center

Krebs, Saskia Susanne; Roebers, Claudia Maria

2012-01-01

This multi-phase study examined the influence of retrieval processes on children's metacognitive processes in relation to and in interaction with achievement level and age. First, N = 150 9/10- and 11/12-year old high and low achievers watched an educational film and predicted their test performance. Children then solved a cloze test regarding the…

Design and implementation of an Internet based effective controlling and monitoring system with wireless fieldbus communications technologies for process automation--an experimental study.

PubMed

Cetinceviz, Yucel; Bayindir, Ramazan

2012-05-01

The network requirements of control systems in industrial applications increase day by day. The Internet based control system and various fieldbus systems have been designed in order to meet these requirements. This paper describes an Internet based control system with wireless fieldbus communication designed for distributed processes. The system was implemented as an experimental setup in a laboratory. In industrial facilities, the process control layer and the distance connection of the distributed control devices in the lowest levels of the industrial production environment are provided with fieldbus networks. In this paper, the Internet based control system that will be able to meet the system requirements with a new-generation communication structure, which is called wired/wireless hybrid system, has been designed on field level and carried out to cover all sectors of distributed automation, from process control, to distributed input/output (I/O). The system has been accomplished by hardware structure with a programmable logic controller (PLC), a communication processor (CP) module, two industrial wireless modules and a distributed I/O module, Motor Protection Package (MPP) and software structure with WinCC flexible program used for the screen of Scada (Supervisory Control And Data Acquisition), SIMATIC MANAGER package program ("STEP7") used for the hardware and network configuration and also for downloading control program to PLC. Copyright © 2012 ISA. Published by Elsevier Ltd. All rights reserved.

PSO-tuned PID controller for coupled tank system via priority-based fitness scheme

NASA Astrophysics Data System (ADS)

Jaafar, Hazriq Izzuan; Hussien, Sharifah Yuslinda Syed; Selamat, Nur Asmiza; Abidin, Amar Faiz Zainal; Aras, Mohd Shahrieel Mohd; Nasir, Mohamad Na'im Mohd; Bohari, Zul Hasrizal

2015-05-01

The industrial applications of Coupled Tank System (CTS) are widely used especially in chemical process industries. The overall process is require liquids to be pumped, stored in the tank and pumped again to another tank. Nevertheless, the level of liquid in tank need to be controlled and flow between two tanks must be regulated. This paper presents development of an optimal PID controller for controlling the desired liquid level of the CTS. Two method of Particle Swarm Optimization (PSO) algorithm will be tested in optimizing the PID controller parameters. These two methods of PSO are standard Particle Swarm Optimization (PSO) and Priority-based Fitness Scheme in Particle Swarm Optimization (PFPSO). Simulation is conducted within Matlab environment to verify the performance of the system in terms of settling time (Ts), steady state error (SSE) and overshoot (OS). It has been demonstrated that implementation of PSO via Priority-based Fitness Scheme (PFPSO) for this system is potential technique to control the desired liquid level and improve the system performances compared with standard PSO.

A procedure concept for local reflex control of grasping

NASA Technical Reports Server (NTRS)

Fiorini, Paolo; Chang, Jeffrey

1989-01-01

An architecture is proposed for the control of robotic devices, and in particular of anthropomorphic hands, characterized by a hierarchical structure in which every level of the architecture contains data and control function with varying degree of abstraction. Bottom levels of the hierarchy interface directly with sensors and actuators, and process raw data and motor commands. Higher levels perform more symbolic types of tasks, such as application of boolean rules and general planning operations. Layers implementation has to be consistent with the type of operation and its requirements for real time control. It is proposed to implement the rule level with a Boolean Artificial Neural Network characterized by a response time sufficient for producing reflex corrective action at the actuator level.

Transcription factor YY1 can control AID-mediated mutagenesis in mice.

PubMed

Zaprazna, Kristina; Basu, Arindam; Tom, Nikola; Jha, Vibha; Hodawadekar, Suchita; Radova, Lenka; Malcikova, Jitka; Tichy, Boris; Pospisilova, Sarka; Atchison, Michael L

2018-02-01

Activation-induced cytidine deminase (AID) is crucial for controlling the immunoglobulin (Ig) diversification processes of somatic hypermutation (SHM) and class switch recombination (CSR). AID initiates these processes by deamination of cytosine, ultimately resulting in mutations or double strand DNA breaks needed for SHM and CSR. Levels of AID control mutation rates, and off-target non-Ig gene mutations can contribute to lymphomagenesis. Therefore, factors that control AID levels in the nucleus can regulate SHM and CSR, and may contribute to disease. We previously showed that transcription factor YY1 can regulate the level of AID in the nucleus and Ig CSR. Therefore, we hypothesized that conditional knock-out of YY1 would lead to reduction in AID localization at the Ig locus, and reduced AID-mediated mutations. Using mice that overexpress AID (IgκAID yy1 f/f ) or that express normal AID levels (yy1 f/f ), we found that conditional knock-out of YY1 results in reduced AID nuclear levels, reduced localization of AID to the Sμ switch region, and reduced AID-mediated mutations. We find that the mechanism of YY1 control of AID nuclear accumulation is likely due to YY1-AID physical interaction which blocks AID ubiquitination. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

What role does the anterior temporal lobe play in sentence-level processing? Neural correlates of syntactic processing in semantic variant primary progressive aphasia.

PubMed

Wilson, Stephen M; DeMarco, Andrew T; Henry, Maya L; Gesierich, Benno; Babiak, Miranda; Mandelli, Maria Luisa; Miller, Bruce L; Gorno-Tempini, Maria Luisa

2014-05-01

Neuroimaging and neuropsychological studies have implicated the anterior temporal lobe (ATL) in sentence-level processing, with syntactic structure-building and/or combinatorial semantic processing suggested as possible roles. A potential challenge to the view that the ATL is involved in syntactic aspects of sentence processing comes from the clinical syndrome of semantic variant primary progressive aphasia (semantic PPA; also known as semantic dementia). In semantic PPA, bilateral neurodegeneration of the ATLs is associated with profound lexical semantic deficits, yet syntax is strikingly spared. The goal of this study was to investigate the neural correlates of syntactic processing in semantic PPA to determine which regions normally involved in syntactic processing are damaged in semantic PPA and whether spared syntactic processing depends on preserved functionality of intact regions, preserved functionality of atrophic regions, or compensatory functional reorganization. We scanned 20 individuals with semantic PPA and 24 age-matched controls using structural MRI and fMRI. Participants performed a sentence comprehension task that emphasized syntactic processing and minimized lexical semantic demands. We found that, in controls, left inferior frontal and left posterior temporal regions were modulated by syntactic processing, whereas anterior temporal regions were not significantly modulated. In the semantic PPA group, atrophy was most severe in the ATLs but extended to the posterior temporal regions involved in syntactic processing. Functional activity for syntactic processing was broadly similar in patients and controls; in particular, whole-brain analyses revealed no significant differences between patients and controls in the regions modulated by syntactic processing. The atrophic left ATL did show abnormal functionality in semantic PPA patients; however, this took the unexpected form of a failure to deactivate. Taken together, our findings indicate that spared syntactic processing in semantic PPA depends on preserved functionality of structurally intact left frontal regions and moderately atrophic left posterior temporal regions, but no functional reorganization was apparent as a consequence of anterior temporal atrophy and dysfunction. These results suggest that the role of the ATL in sentence processing is less likely to relate to syntactic structure-building and more likely to relate to higher-level processes such as combinatorial semantic processing.

Application of Sigma Metrics Analysis for the Assessment and Modification of Quality Control Program in the Clinical Chemistry Laboratory of a Tertiary Care Hospital.

PubMed

Iqbal, Sahar; Mustansar, Tazeen

2017-03-01

Sigma is a metric that quantifies the performance of a process as a rate of Defects-Per-Million opportunities. In clinical laboratories, sigma metric analysis is used to assess the performance of laboratory process system. Sigma metric is also used as a quality management strategy for a laboratory process to improve the quality by addressing the errors after identification. The aim of this study is to evaluate the errors in quality control of analytical phase of laboratory system by sigma metric. For this purpose sigma metric analysis was done for analytes using the internal and external quality control as quality indicators. Results of sigma metric analysis were used to identify the gaps and need for modification in the strategy of laboratory quality control procedure. Sigma metric was calculated for quality control program of ten clinical chemistry analytes including glucose, chloride, cholesterol, triglyceride, HDL, albumin, direct bilirubin, total bilirubin, protein and creatinine, at two control levels. To calculate the sigma metric imprecision and bias was calculated with internal and external quality control data, respectively. The minimum acceptable performance was considered as 3 sigma. Westgard sigma rules were applied to customize the quality control procedure. Sigma level was found acceptable (≥3) for glucose (L2), cholesterol, triglyceride, HDL, direct bilirubin and creatinine at both levels of control. For rest of the analytes sigma metric was found <3. The lowest value for sigma was found for chloride (1.1) at L2. The highest value of sigma was found for creatinine (10.1) at L3. HDL was found with the highest sigma values at both control levels (8.8 and 8.0 at L2 and L3, respectively). We conclude that analytes with the sigma value <3 are required strict monitoring and modification in quality control procedure. In this study application of sigma rules provided us the practical solution for improved and focused design of QC procedure.

A whole process quality control system for energy measuring instruments inspection based on IOT technology

NASA Astrophysics Data System (ADS)

Yin, Bo; Liu, Li; Wang, Jiahan; Li, Xiran; Liu, Zhenbo; Li, Dewei; Wang, Jun; Liu, Lu; Wu, Jun; Xu, Tingting; Cui, He

2017-10-01

Electric energy measurement as a basic work, an accurate measurements play a vital role for the economic interests of both parties of power supply, the standardized management of the measurement laboratory at all levels is a direct factor that directly affects the fairness of measurement. Currently, the management of metering laboratories generally uses one-dimensional bar code as the recognition object, advances the testing process by manual management, most of the test data requires human input to generate reports. There are many problems and potential risks in this process: Data cannot be saved completely, cannot trace the status of inspection, the inspection process isn't completely controllable and so on. For the provincial metrology center's actual requirements of the whole process management for the performance test of the power measuring appliances, using of large-capacity RF tags as a process management information media, we developed a set of general measurement experiment management system, formulated a standardized full performance test process, improved the raw data recording mode of experimental process, developed a storehouse automatic inventory device, established a strict test sample transfer and storage system, ensured that all the raw data of the inspection can be traced back, achieved full life-cycle control of the sample, significantly improved the quality control level and the effectiveness of inspection work.

Emotional prosody processing in autism spectrum disorder

PubMed Central

Kliemann, Dorit; Dziobek, Isabel; Heekeren, Hauke R.

2017-01-01

Abstract Individuals with Autism Spectrum Disorder (ASD) are characterized by severe deficits in social communication, whereby the nature of their impairments in emotional prosody processing have yet to be specified. Here, we investigated emotional prosody processing in individuals with ASD and controls with novel, lifelike behavioral and neuroimaging paradigms. Compared to controls, individuals with ASD showed reduced emotional prosody recognition accuracy on a behavioral task. On the neural level, individuals with ASD displayed reduced activity of the STS, insula and amygdala for complex vs basic emotions compared to controls. Moreover, the coupling between the STS and amygdala for complex vs basic emotions was reduced in the ASD group. Finally, groups differed with respect to the relationship between brain activity and behavioral performance. Brain activity during emotional prosody processing was more strongly related to prosody recognition accuracy in ASD participants. In contrast, the coupling between STS and anterior cingulate cortex (ACC) activity predicted behavioral task performance more strongly in the control group. These results provide evidence for aberrant emotional prosody processing of individuals with ASD. They suggest that the differences in the relationship between the neural and behavioral level of individuals with ASD may account for their observed deficits in social communication. PMID:27531389

The effects of familiarity and emotional expression on face processing examined by ERPs in patients with schizophrenia.

PubMed

Caharel, Stéphanie; Bernard, Christian; Thibaut, Florence; Haouzir, Sadec; Di Maggio-Clozel, Carole; Allio, Gabrielle; Fouldrin, Gaël; Petit, Michel; Lalonde, Robert; Rebaï, Mohamed

2007-09-01

The main objective of the study was to determine whether patients with schizophrenia are deficient relative to controls in the processing of faces at different levels of familiarity and types of emotion and the stage where such differences may occur. ERPs based on 18 patients with schizophrenia and 18 controls were compared in a face identification task at three levels of familiarity (unknown, familiar, subject's own) and for three types of emotion (disgust, smiling, neutral). The schizophrenic group was less accurate than controls in the face processing, especially for unknown faces and those expressing negative emotions such as disgust. P1 and N170 amplitudes were lower and P1, N170, P250 amplitudes were of slower onset in patients with schizophrenia. N170 and P250 amplitudes were modulated by familiarity and face expression in a different manner in patients than controls. Schizophrenia is associated with a genelarized defect of face processing, both in terms of familiarity and emotional expression, attributable to deficient processing at sensory (P1) and perceptual (N170) stages. These patients appear to have difficulty in encoding the structure of a face and thereby do not evaluate correctly familiarity and emotion.

Differences in net primary production and biogeochemistry between contrasting floodplain forests

Treesearch

Erik B. Schilling; B. Graeme Lockaby

2000-01-01

A firm understanding of the driving forces controlling variation among wetland forests continues to elude scientists and land managers—specifically the biogeochemical processes controlling vegetation production. Within contrasting wetland forests, insight into the biogeochemical processes driving productivity levels may befound by examining the degree to which nitrogen...

Catchment hydrological responses to forest harvest amount and spatial pattern

Treesearch

Alex Abdelnour; Marc Stieglitz; Feifei Pan; Robert McKane

2011-01-01

Forest harvest effects on streamflow generation have been well described experimentally, but a clear understanding of process-level hydrological controls can be difficult to ascertain from data alone. We apply a new model, Visualizing Ecosystems for Land Management Assessments (VELMA), to elucidate how hillslope and catchment-scale processes control stream discharge in...

Potato powders prepared by successive cooking-process depending on resistant starch content affect the intestinal fermentation in rats.

PubMed

Kawakami, Sakura; Han, Kyu-Ho; Araki, Takahiro; Ohba, Kiyoshi; Wakabayashi, Tatsuya; Shimada, Kenichiro; Fukushima, Michihiro

2017-02-01

The effects of resistant starch (RS) in dry potato powders prepared by various processes on intestinal fermentation in rats were assessed. Rats were fed raw potato powder (RP), blanched potato powder (BP), steamed potato powder (SP), or drum-dried potato powder (DP) for 4 weeks. The cecal RS content was significantly higher in the RP group than in the control diet (CN) group and other dry potato powder groups. Cecum pH was significantly lower in the RP group compared to the CN group, and was also significantly lower than that in the SP, BP, and DP groups. Lactic acid bacteria levels in the RP group were significantly higher than those in the CN group, and levels in the SP group also increased relative to the control group. Lactobacillus levels in the RP group were higher than in the CN and other dry potato powder groups. Cecal short-chain fatty acid (SCFA) concentrations in the RP group followed by the SP group exhibited significantly higher levels relative to the control levels. Dry potato powders containing RS produced during the cooking process may represent a useful food material that increases intestinal concentrations of SCFA and enhances the growth of certain lactic acid bacteria.

Emotional Experience in Negative Symptoms of Schizophrenia—No Evidence for a Generalized Hedonic Deficit

PubMed Central

Oorschot, Margreet; Lataster, Tineke; Thewissen, Viviane; Lardinois, Mariëlle; Wichers, Marieke; van Os, Jim; Delespaul, Philippe; Myin-Germeys, Inez

2013-01-01

Background: Deficits in emotion processing are thought to underlie the key negative symptoms flat affect and anhedonia observed in psychotic disorders. This study investigated emotional experience and social behavior in the realm of daily life in a sample of patients with schizophrenia and schizoaffective disorder, stratified by level of negative symptoms. Methods: Emotional experience and behavior of 149 patients with schizophrenia and schizoaffective disorder and 143 controls were explored using the Experience Sampling Method. Results: Patients reported lower levels of positive and higher levels of negative affect compared with controls. High negative symptom patients reported similar emotional stability and capacity to generate positive affect as controls, whereas low negative symptom patients reported increased instability. All participants displayed roughly comparable emotional responses to the company of other people. However, in comparison with controls, patients showed more social withdrawal and preference to be alone while in company, particularly the high negative symptom group. Conclusions: This study revealed no evidence for a generalized hedonic deficit in patients with psychotic spectrum disorders. Lower rather than higher levels of negative symptoms were associated with a pattern of emotional processing which was different from healthy controls. PMID:22021660

Visual temporal processing in dyslexia and the magnocellular deficit theory: the need for speed?

PubMed

McLean, Gregor M T; Stuart, Geoffrey W; Coltheart, Veronika; Castles, Anne

2011-12-01

A controversial question in reading research is whether dyslexia is associated with impairments in the magnocellular system and, if so, how these low-level visual impairments might affect reading acquisition. This study used a novel chromatic flicker perception task to specifically explore temporal aspects of magnocellular functioning in 40 children with dyslexia and 42 age-matched controls (aged 7-11). The relationship between magnocellular temporal resolution and higher-level aspects of visual temporal processing including inspection time, single and dual-target (attentional blink) RSVP performance, go/no-go reaction time, and rapid naming was also assessed. The Dyslexia group exhibited significant deficits in magnocellular temporal resolution compared with controls, but the two groups did not differ in parvocellular temporal resolution. Despite the significant group differences, associations between magnocellular temporal resolution and reading ability were relatively weak, and links between low-level temporal resolution and reading ability did not appear specific to the magnocellular system. Factor analyses revealed that a collective Perceptual Speed factor, involving both low-level and higher-level visual temporal processing measures, accounted for unique variance in reading ability independently of phonological processing, rapid naming, and general ability.

High-powered CO2 -lasers and noise control

NASA Astrophysics Data System (ADS)

Honkasalo, Antero; Kuronen, Juhani

High-power CO2 -lasers are being more and more widely used for welding, drilling and cutting in machine shops. In the near future, different kinds of surface treatments will also become routine practice with laser units. The industries benefitting most from high power lasers will be: the automotive industry, shipbuilding, the offshore industry, the aerospace industry, the nuclear and the chemical processing industries. Metal processing lasers are interesting from the point of view of noise control because the working tool is a laser beam. It is reasonable to suppose that the use of such laser beams will lead to lower noise levels than those connected with traditional metal processing methods and equipment. In the following presentation, the noise levels and possible noise-control problems attached to the use of high-powered CO2 -lasers are studied.

Molecular Rotors

DTIC Science & Technology

2006-10-31

microwave signal processing components, and micro-fluidic devices. The projected involved the preparation, surface mounting, and characterization of...Guisinger, R. Basu, and M. C. Hersam, “Atomic-level characterization and control of free radical surface chemistry using scanning tunneling microscopy...Basu, and M. C. Hersam, “Atomic level characterization and control of organosilicon surface chemistry using scanning tunneling microscopy,” presented

Positive electrode processing for Hughes NiH2 cells

NASA Technical Reports Server (NTRS)

Bleser, C. A.

1982-01-01

The basic procedures were developed for the manufacture of nickel cadmium batteries. An electrochemical impregnation in an aqueous ethanol solution is used in this process. Several additional controls were instituted for production of flight electrodes, including a Hughes controlled MCD, a solution reserved exclusively for the impregnation of Hughes positive electrodes a system of complete traceability for individual electrodes, an electrical characterization test to provide information on weight and capacity at the plaque level, and a stress test to provide data on capacity, weight, and physical parameters at the electrode level.

Multi-variants synthesis of Petri nets for FPGA devices

NASA Astrophysics Data System (ADS)

Bukowiec, Arkadiusz; Doligalski, Michał

2015-09-01

There is presented new method of synthesis of application specific logic controllers for FPGA devices. The specification of control algorithm is made with use of control interpreted Petri net (PT type). It allows specifying parallel processes in easy way. The Petri net is decomposed into state-machine type subnets. In this case, each subnet represents one parallel process. For this purpose there are applied algorithms of coloring of Petri nets. There are presented two approaches of such decomposition: with doublers of macroplaces or with one global wait place. Next, subnets are implemented into two-level logic circuit of the controller. The levels of logic circuit are obtained as a result of its architectural decomposition. The first level combinational circuit is responsible for generation of next places and second level decoder is responsible for generation output symbols. There are worked out two variants of such circuits: with one shared operational memory or with many flexible distributed memories as a decoder. Variants of Petri net decomposition and structures of logic circuits can be combined together without any restrictions. It leads to existence of four variants of multi-variants synthesis.

Deaf individuals who work with computers present a high level of visual attention

PubMed Central

Ribeiro, Paula Vieira; Ribas, Valdenilson Ribeiro; Ribas, Renata de Melo Guerra; de Melo, Teresinha de Jesus Oliveira Guimarães; Marinho, Carlos Antonio de Sá; Silva, Kátia Karina do Monte; de Albuquerque, Elizabete Elias; Ribas, Valéria Ribeiro; de Lima, Renata Mirelly Silva; Santos, Tuthcha Sandrelle Botelho Tavares

2011-01-01

Some studies in the literature indicate that deaf individuals seem to develop a higher level of attention and concentration during the process of constructing of different ways of communicating. Objective The aim of this study was to evaluate the level of attention in individuals deaf from birth that worked with computers. Methods A total of 161 individuals in the 18-25 age group were assessed. Of these, 40 were congenitally deaf individuals that worked with computers, 42 were deaf individuals that did not work, did not know how to use nor used computers (Control 1), 39 individuals with normal hearing that did not work, did not know how to use computers nor used them (Control 2), and 40 individuals with normal hearing that worked with computers (Control 3). Results The group of subjects deaf from birth that worked with computers (IDWC) presented a higher level of focused attention, sustained attention, mental manipulation capacity and resistance to interference compared to the control groups. Conclusion This study highlights the relevance sensory to cognitive processing. PMID:29213734

Theory of Mind and Executive Control Deficits in Typically Developing Adults and Adolescents with High Levels of Autism Traits.

PubMed

Gökçen, Elif; Frederickson, Norah; Petrides, K V

2016-06-01

Autism spectrum disorder (ASD) is characterised by profound difficulties in empathic processing and executive control. Whilst the links between these processes have been frequently investigated in populations with autism, few studies have examined them at the subclinical level. In addition, the contribution of alexithymia, a trait characterised by impaired interoceptive awareness and empathy, and elevated in those with ASD, is currently unclear. The present two-part study employed a comprehensive battery of tasks to examine these processes. Findings support the notion that executive function and theory of mind are related abilities. They also suggest that individuals with elevated levels of autism-like traits experience a partially similar pattern of social and executive function difficulties to those diagnosed with ASD, and that these impairments are not explained by co-occurring alexithymia.

A Technique for Transient Thermal Testing of Thick Structures

NASA Technical Reports Server (NTRS)

Horn, Thomas J.; Richards, W. Lance; Gong, Leslie

1997-01-01

A new open-loop heat flux control technique has been developed to conduct transient thermal testing of thick, thermally-conductive aerospace structures. This technique uses calibration of the radiant heater system power level as a function of heat flux, predicted aerodynamic heat flux, and the properties of an instrumented test article. An iterative process was used to generate open-loop heater power profiles prior to each transient thermal test. Differences between the measured and predicted surface temperatures were used to refine the heater power level command profiles through the iteration process. This iteration process has reduced the effects of environmental and test system design factors, which are normally compensated for by closed-loop temperature control, to acceptable levels. The final revised heater power profiles resulted in measured temperature time histories which deviated less than 25 F from the predicted surface temperatures.

The effectivenes of science domain-based science learning integrated with local potency

NASA Astrophysics Data System (ADS)

Kurniawati, Arifah Putri; Prasetyo, Zuhdan Kun; Wilujeng, Insih; Suryadarma, I. Gusti Putu

2017-08-01

This research aimed to determine the significant effect of science domain-based science learning integrated with local potency toward science process skills. The research method used was a quasi-experimental design with nonequivalent control group design. The population of this research was all students of class VII SMP Negeri 1 Muntilan. The sample of this research was selected through cluster random sampling, namely class VII B as an experiment class (24 students) and class VII C as a control class (24 students). This research used a test instrument that was adapted from Agus Dwianto's research. The aspect of science process skills in this research was observation, classification, interpretation and communication. The analysis of data used the one factor anova at 0,05 significance level and normalized gain score. The significance level result of science process skills with one factor anova is 0,000. It shows that the significance level < alpha (0,05). It means that there was significant effect of science domain-based science learning integrated with local potency toward science learning process skills. The results of analysis show that the normalized gain score are 0,29 (low category) in control class and 0,67 (medium category) in experiment class.

Software Architecture to Support the Evolution of the ISRU RESOLVE Engineering Breadboard Unit 2 (EBU2)

NASA Technical Reports Server (NTRS)

Moss, Thomas; Nurge, Mark; Perusich, Stephen

2011-01-01

The In-Situ Resource Utilization (ISRU) Regolith & Environmental Science and Oxygen & Lunar Volatiles Extraction (RESOLVE) software provides operation of the physical plant from a remote location with a high-level interface that can access and control the data from external software applications of other subsystems. This software allows autonomous control over the entire system with manual computer control of individual system/process components. It gives non-programmer operators the capability to easily modify the high-level autonomous sequencing while the software is in operation, as well as the ability to modify the low-level, file-based sequences prior to the system operation. Local automated control in a distributed system is also enabled where component control is maintained during the loss of network connectivity with the remote workstation. This innovation also minimizes network traffic. The software architecture commands and controls the latest generation of RESOLVE processes used to obtain, process, and quantify lunar regolith. The system is grouped into six sub-processes: Drill, Crush, Reactor, Lunar Water Resource Demonstration (LWRD), Regolith Volatiles Characterization (RVC) (see example), and Regolith Oxygen Extraction (ROE). Some processes are independent, some are dependent on other processes, and some are independent but run concurrently with other processes. The first goal is to analyze the volatiles emanating from lunar regolith, such as water, carbon monoxide, carbon dioxide, ammonia, hydrogen, and others. This is done by heating the soil and analyzing and capturing the volatilized product. The second goal is to produce water by reducing the soil at high temperatures with hydrogen. This is done by raising the reactor temperature in the range of 800 to 900 C, causing the reaction to progress by adding hydrogen, and then capturing the water product in a desiccant bed. The software needs to run the entire unit and all sub-processes; however, throughout testing, many variables and parameters need to be changed as more is learned about the system operation. The Master Events Controller (MEC) is run on a standard laptop PC using Windows XP. This PC runs in parallel to another laptop that monitors the GC, and a third PC that monitors the drilling/ crushing operation. These three PCs interface to the process through a CompactRIO, OPC Servers, and modems.

Defense waste processing facility (DWPF) liquids model: revisions for processing higher TIO 2 containing glasses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jantzen, C. M.; Edwards, T. B.; Trivelpiece, C. L.

Radioactive high level waste (HLW) at the Savannah River Site (SRS) has successfully been vitrified into borosilicate glass in the Defense Waste Processing Facility (DWPF) since 1996. Vitrification requires stringent product/process (P/P) constraints since the glass cannot be reworked once it is poured into ten foot tall by two foot diameter canisters. A unique “feed forward” statistical process control (SPC) was developed for this control rather than statistical quality control (SQC). In SPC, the feed composition to the DWPF melter is controlled prior to vitrification. In SQC, the glass product would be sampled after it is vitrified. Individual glass property-compositionmore » models form the basis for the “feed forward” SPC. The models transform constraints on the melt and glass properties into constraints on the feed composition going to the melter in order to guarantee, at the 95% confidence level, that the feed will be processable and that the durability of the resulting waste form will be acceptable to a geologic repository. This report documents the development of revised TiO 2, Na 2O, Li 2O and Fe 2O 3 coefficients in the SWPF liquidus model and revised coefficients (a, b, c, and d).« less

75 FR 47546 - Materials Processing Equipment; Technical Advisory Committee; Notice of Partially Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-06

... questions that affect the level of export controls applicable to materials processing equipment and related... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment; Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical...

75 FR 66356 - Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-28

... questions that affect the level of export controls applicable to materials processing equipment and related... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical...

78 FR 13625 - Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-28

... questions that affect the level of export controls applicable to materials processing equipment and related... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical...

77 FR 65857 - Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-31

... questions that affect the level of export controls applicable to materials processing equipment and related... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical...

76 FR 20949 - Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-14

... that affect the level of export controls applicable to materials processing equipment and related... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical...

77 FR 42483 - Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-19

... questions that affect the level of export controls applicable to materials processing equipment and related... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical...

78 FR 24160 - Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-24

... questions that affect the level of export controls applicable to materials processing equipment and related... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical...

77 FR 25960 - Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-02

... questions that affect the level of export controls applicable to materials processing equipment and related... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical...

78 FR 42754 - Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-17

... questions that affect the level of export controls applicable to materials processing equipment and related... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical...

76 FR 42678 - Materials Processing Equipment; Technical Advisory Committee; Notice of Partially Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-19

... questions that affect the level of export controls applicable to materials processing equipment and related... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment; Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical...

78 FR 63161 - Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-23

... questions that affect the level of export controls applicable to materials processing equipment and related... DEPARTMENT OF COMMERCE Bureau of Industry and Security Materials Processing Equipment Technical Advisory Committee; Notice of Partially Closed Meeting The Materials Processing Equipment Technical...

SU-E-CAMPUS-T-04: Statistical Process Control for Patient-Specific QA in Proton Beams

DOE Office of Scientific and Technical Information (OSTI.GOV)

LAH, J; SHIN, D; Kim, G

Purpose: To evaluate and improve the reliability of proton QA process, to provide an optimal customized level using the statistical process control (SPC) methodology. The aim is then to suggest the suitable guidelines for patient-specific QA process. Methods: We investigated the constancy of the dose output and range to see whether it was within the tolerance level of daily QA process. This study analyzed the difference between the measured and calculated ranges along the central axis to suggest the suitable guidelines for patient-specific QA in proton beam by using process capability indices. In this study, patient QA plans were classifiedmore » into 6 treatment sites: head and neck (41 cases), spinal cord (29 cases), lung (28 cases), liver (30 cases), pancreas (26 cases), and prostate (24 cases). Results: The deviations for the dose output and range of daily QA process were ±0.84% and ±019%, respectively. Our results show that the patient-specific range measurements are capable at a specification limit of ±2% in all treatment sites except spinal cord cases. In spinal cord cases, comparison of process capability indices (Cp, Cpm, Cpk ≥1, but Cpmk ≤1) indicated that the process is capable, but not centered, the process mean deviates from its target value. The UCL (upper control limit), CL (center line) and LCL (lower control limit) for spinal cord cases were 1.37%, −0.27% and −1.89%, respectively. On the other hands, the range differences in prostate cases were good agreement between calculated and measured values. The UCL, CL and LCL for prostate cases were 0.57%, −0.11% and −0.78%, respectively. Conclusion: SPC methodology has potential as a useful tool to customize an optimal tolerance levels and to suggest the suitable guidelines for patient-specific QA in clinical proton beam.« less

Levels of integration in cognitive control and sequence processing in the prefrontal cortex.

PubMed

Bahlmann, Jörg; Korb, Franziska M; Gratton, Caterina; Friederici, Angela D

2012-01-01

Cognitive control is necessary to flexibly act in changing environments. Sequence processing is needed in language comprehension to build the syntactic structure in sentences. Functional imaging studies suggest that sequence processing engages the left ventrolateral prefrontal cortex (PFC). In contrast, cognitive control processes additionally recruit bilateral rostral lateral PFC regions. The present study aimed to investigate these two types of processes in one experimental paradigm. Sequence processing was manipulated using two different sequencing rules varying in complexity. Cognitive control was varied with different cue-sets that determined the choice of a sequencing rule. Univariate analyses revealed distinct PFC regions for the two types of processing (i.e. sequence processing: left ventrolateral PFC and cognitive control processing: bilateral dorsolateral and rostral PFC). Moreover, in a common brain network (including left lateral PFC and intraparietal sulcus) no interaction between sequence and cognitive control processing was observed. In contrast, a multivariate pattern analysis revealed an interaction of sequence and cognitive control processing, such that voxels in left lateral PFC and parietal cortex showed different tuning functions for tasks involving different sequencing and cognitive control demands. These results suggest that the difference between the process of rule selection (i.e. cognitive control) and the process of rule-based sequencing (i.e. sequence processing) find their neuronal underpinnings in distinct activation patterns in lateral PFC. Moreover, the combination of rule selection and rule sequencing can shape the response of neurons in lateral PFC and parietal cortex.

Levels of Integration in Cognitive Control and Sequence Processing in the Prefrontal Cortex

PubMed Central

Bahlmann, Jörg; Korb, Franziska M.; Gratton, Caterina; Friederici, Angela D.

2012-01-01

Cognitive control is necessary to flexibly act in changing environments. Sequence processing is needed in language comprehension to build the syntactic structure in sentences. Functional imaging studies suggest that sequence processing engages the left ventrolateral prefrontal cortex (PFC). In contrast, cognitive control processes additionally recruit bilateral rostral lateral PFC regions. The present study aimed to investigate these two types of processes in one experimental paradigm. Sequence processing was manipulated using two different sequencing rules varying in complexity. Cognitive control was varied with different cue-sets that determined the choice of a sequencing rule. Univariate analyses revealed distinct PFC regions for the two types of processing (i.e. sequence processing: left ventrolateral PFC and cognitive control processing: bilateral dorsolateral and rostral PFC). Moreover, in a common brain network (including left lateral PFC and intraparietal sulcus) no interaction between sequence and cognitive control processing was observed. In contrast, a multivariate pattern analysis revealed an interaction of sequence and cognitive control processing, such that voxels in left lateral PFC and parietal cortex showed different tuning functions for tasks involving different sequencing and cognitive control demands. These results suggest that the difference between the process of rule selection (i.e. cognitive control) and the process of rule-based sequencing (i.e. sequence processing) find their neuronal underpinnings in distinct activation patterns in lateral PFC. Moreover, the combination of rule selection and rule sequencing can shape the response of neurons in lateral PFC and parietal cortex. PMID:22952762

Endogenous testosterone levels are associated with neural activity in men with schizophrenia during facial emotion processing.

PubMed

Ji, Ellen; Weickert, Cynthia Shannon; Lenroot, Rhoshel; Catts, Stanley V; Vercammen, Ans; White, Christopher; Gur, Raquel E; Weickert, Thomas W

2015-06-01

Growing evidence suggests that testosterone may play a role in the pathophysiology of schizophrenia given that testosterone has been linked to cognition and negative symptoms in schizophrenia. Here, we determine the extent to which serum testosterone levels are related to neural activity in affective processing circuitry in men with schizophrenia. Functional magnetic resonance imaging was used to measure blood-oxygen-level-dependent signal changes as 32 healthy controls and 26 people with schizophrenia performed a facial emotion identification task. Whole brain analyses were performed to determine regions of differential activity between groups during processing of angry versus non-threatening faces. A follow-up ROI analysis using a regression model in a subset of 16 healthy men and 16 men with schizophrenia was used to determine the extent to which serum testosterone levels were related to neural activity. Healthy controls displayed significantly greater activation than people with schizophrenia in the left inferior frontal gyrus (IFG). There was no significant difference in circulating testosterone levels between healthy men and men with schizophrenia. Regression analyses between activation in the IFG and circulating testosterone levels revealed a significant positive correlation in men with schizophrenia (r=.63, p=.01) and no significant relationship in healthy men. This study provides the first evidence that circulating serum testosterone levels are related to IFG activation during emotion face processing in men with schizophrenia but not in healthy men, which suggests that testosterone levels modulate neural processes relevant to facial emotion processing that may interfere with social functioning in men with schizophrenia. Crown Copyright © 2015. Published by Elsevier B.V. All rights reserved.

Face-name association learning and brain structural substrates in alcoholism.

PubMed

Pitel, Anne-Lise; Chanraud, Sandra; Rohlfing, Torsten; Pfefferbaum, Adolf; Sullivan, Edith V

2012-07-01

Associative learning is required for face-name association and is impaired in alcoholism, but the cognitive processes and brain structural components underlying this deficit remain unclear. It is also unknown whether prompting alcoholics to implement a deep level of processing during face-name encoding would enhance performance. Abstinent alcoholics and controls performed a levels-of-processing face-name learning task. Participants indicated whether the face was that of an honest person (deep encoding) or that of a man (shallow encoding). Retrieval was examined using an associative (face-name) recognition task and a single-item (face or name only) recognition task. Participants also underwent 3T structural MRI. Compared with controls, alcoholics had poorer associative and single-item learning and performed at similar levels. Level of processing at encoding had little effect on recognition performance but affected reaction time (RT). Correlations with brain volumes were generally modest and based primarily on RT in alcoholics, where the deeper the processing at encoding, the more restricted the correlations with brain volumes. In alcoholics, longer control task RTs correlated modestly with smaller tissue volumes across several anterior to posterior brain regions; shallow encoding correlated with calcarine and striatal volumes; deep encoding correlated with precuneus and parietal volumes; and associative recognition RT correlated with cerebellar volumes. In controls, poorer associative recognition with deep encoding correlated significantly with smaller volumes of frontal and striatal structures. Despite prompting, alcoholics did not take advantage of encoding memoranda at a deep level to enhance face-name recognition accuracy. Nonetheless, conditions of deeper encoding resulted in faster RTs and more specific relations with regional brain volumes than did shallow encoding. The normal relation between associative recognition and corticostriatal volumes was not present in alcoholics. Rather, their speeded RTs occurred at the expense of accuracy and were related most robustly to cerebellar volumes. Copyright © 2012 by the Research Society on Alcoholism.

Dietary self-control is related to the speed with which attributes of healthfulness and tastiness are processed.

PubMed

Sullivan, Nicolette; Hutcherson, Cendri; Harris, Alison; Rangel, Antonio

2015-02-01

We propose that self-control failures, and variation across individuals in self-control abilities, are partly due to differences in the speed with which the decision-making circuitry processes basic attributes, such as tastiness, versus more abstract attributes, such as healthfulness. We tested these hypotheses by combining a dietary-choice task with a novel form of mouse tracking that allowed us to pinpoint when different attributes were being integrated into the choice process with temporal resolution at the millisecond level. We found that, on average, tastiness was processed about 195 ms earlier than healthfulness during the choice process. We also found that 13% to 39% of observed individual differences in self-control ability could be explained by differences in the relative speed with which tastiness and healthfulness were processed. © The Author(s) 2014.

Control relaxation via dephasing: A quantum-state-diffusion study

NASA Astrophysics Data System (ADS)

Jing, Jun; Yu, Ting; Lam, Chi-Hang; You, J. Q.; Wu, Lian-Ao

2018-01-01

Dynamical decoupling as a quantum control strategy aims at suppressing quantum decoherence adopting the popular philosophy that the disorder in the unitary evolution of the open quantum system caused by environmental noises should be neutralized by a sequence of ordered or well-designed external operations acting on the system. This work studies the solution of quantum-state-diffusion equations by mixing two channels of environmental noises, i.e., relaxation (dissipation) and dephasing. It is interesting to find in two-level and three-level atomic systems that a non-Markovian relaxation or dissipation process can be suppressed by a Markovian dephasing noise. The discovery results in an anomalous control strategy by coordinating relaxation and dephasing processes. Our approach opens an avenue of noise control strategy with no artificial manipulation over the open quantum systems.

Liquid and Gaseous Waste Operations Department annual operating report CY 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maddox, J.J.; Scott, C.B.

1997-03-01

This annual report summarizes operating activities dealing with the process waste system, the liquid low-level waste system, and the gaseous waste system. It also describes upgrade activities dealing with the process and liquid low-level waste systems, the cathodic protection system, a stack ventilation system, and configuration control. Maintenance activities are described dealing with nonradiological wastewater treatment plant, process waste treatment plant and collection system, liquid low-level waste system, and gaseous waste system. Miscellaneous activities include training, audits/reviews/tours, and environmental restoration support.

WeaselBoard :

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mulder, John C.; Schwartz, Moses Daniel; Berg, Michael J.

2013-10-01

Critical infrastructures, such as electrical power plants and oil refineries, rely on programmable logic controllers (PLCs) to control essential processes. State of the art security cannot detect attacks on PLCs at the hardware or firmware level. This renders critical infrastructure control systems vulnerable to costly and dangerous attacks. WeaselBoard is a PLC backplane analysis system that connects directly to the PLC backplane to capture backplane communications between modules. WeaselBoard forwards inter-module traffic to an external analysis system that detects changes to process control settings, sensor values, module configuration information, firmware updates, and process control program (logic) updates. WeaselBoard provides zero-daymore » exploit detection for PLCs by detecting changes in the PLC and the process. This approach to PLC monitoring is protected under U.S. Patent Application 13/947,887.« less

Operational factors affecting microgravity levels in orbit

NASA Technical Reports Server (NTRS)

Olsen, R. E.; Mockovciak, J., Jr.

1980-01-01

Microgravity levels desired for proposed materials processing payloads are fundamental considerations in the design of future space platforms. Disturbance sources, such as aerodynamic drag, attitude control torques, crew motion and orbital dynamics, influence the microgravity levels attainable in orbit. The nature of these effects are assessed relative to platform design parameters such as orbital altitude and configuration geometry, and examples are presented for a representative spacecraft configuration. The possible applications of control techniques to provide extremely low acceleration levels are also discussed.

Daily fluctuations in teachers' well-being: a diary study using the Job Demands-Resources model.

PubMed

Simbula, Silvia

2010-10-01

The study tests the dynamic nature of the Job Demands-Resources model with regard to both motivational and health impairment processes. It does so by examining whether daily fluctuations in co-workers' support (i.e., a typical job resource) and daily fluctuations in work/family conflict (i.e., a typical job demand) predict day-levels of job satisfaction and mental health through work engagement and exhaustion, respectively. A total of 61 schoolteachers completed a general questionnaire and a daily survey over a period of five consecutive work days. Multilevel analyses provided evidence for both the above processes. Consistently with the hypotheses, our results showed that day-level work engagement mediated the impact of day-level co-workers' support on day-level job satisfaction and day-level mental health, after general levels of work engagement and outcome variables had been controlled for. Moreover, day-level exhaustion mediated the relationship between day-level work/family conflict and day-level job satisfaction and day-level mental health after general levels of exhaustion and outcome variables had been controlled for. These findings provide new insights into the dynamic psychological processes that determine daily fluctuations in employee well-being. Such insights may be transformed into job redesign strategies and other interventions designed to enhance work-related psychological well-being on a daily level.

Dissociative identity disorder and prepulse inhibition of the acoustic startle reflex

PubMed Central

Dale, Karl Yngvar; Flaten, Magne Arve; Elden, Åke; Holte, Arne

2008-01-01

A group of persons with dissociative identity disorder (DID) was compared with a group of persons with other dissociative disorders, and a group of nondiagnosed controls with regard to prepulse inhibition (PPI) of the acoustic startle reflex. The findings suggest maladaptive attentional processes at a controlled level, but not at a preattentive automatic level, in persons with DID. The prepulse occupied more controlled attentional resources in the DID group compared with the other two groups. Preattentive automatic processing, on the other hand, was normal in the DID group. Moreover, startle reflexes did not habituate in the DID group. In conclusion, increased PPI and delayed habituation is consistent with increased vigilance in individuals with DID. The present findings of reduced habituation of startle reflexes and increased PPI in persons with DID suggest the operation of a voluntary process that directs attention away from unpleasant or threatening stimuli. Aberrant voluntary attentional processes may thus be a defining characteristic in DID. PMID:18830396

[Analysis and countermeasure for quality risk in process of traditional Chinese medicine preparations].

PubMed

Yang, Ming; Yang, Yuan-Zhen; Wang, Ya-Qi; Wu, Zhen-Feng; Wang, Xue-Cheng; Luo, Jing

2017-03-01

Product quality relies on not only testing methods,but also the design and development, production control and product manufacturing all aspects of logistics management. Quality comes from the process control level.Therefore, it is very important to accurately identify the factors that may induce quality risk in the production process and quality control measures correspondingly.This article systematically analyzes the source of the quality risk of all aspects of the production process in traditional Chinese medicine preparation. Discussing ways and methods of quality risk identification of traditional Chinese medicine preparation and providing references for perfecting the whole process quality management of traditional Chinese medicine preparation. Copyright© by the Chinese Pharmaceutical Association.

Cognitive Associates of Current and More Intensive Control of Hypertension: Findings From the Hispanic Community Health Study/Study of Latinos.

PubMed

Lamar, Melissa; Wu, Donghong; Durazo-Arvizu, Ramon A; Brickman, Adam M; Gonzalez, Hector M; Tarraf, Wassim; Daviglus, Martha L

2017-06-01

Hypertension control in Hispanics/Latinos lag behind general US trends by 10-15%. Intensive systolic blood pressure (SBP) management <120 mm Hg may significantly reduce morbidity/mortality risk in adults with hypertension; less is known about cognition. We investigated cross-sectional associations of cognition with observed hypertension control at currently recommended (SBP < 140 mm Hg) and more intensive (SBP < 120 mm Hg) levels using baseline data from the Hispanic Community Health Study/Study of Latinos. From this multicenter cohort study, we focused on 1,735 Hispanic/Latino men and women ages 45-74 years with hypertension and verified antihypertensive use. Verbal fluency, information processing speed, learning, and memory were tested in Spanish or English. Separate linear regressions revealed that being on 1 vs. >1 antihypertensive medication was not associated with cognition; however, individuals with SBP controlled to currently recommended levels outperformed individuals with uncontrolled SBP on verbal fluency [Beta = 1.44 (0.52), P < 0.01] and information processing speed [Beta = 3.01 (0.89), P < 0.001] in age-adjusted regression analyses; only information processing speed remained significant (P < 0.05) after additional adjustments including acculturation, health insurance, and other cardiovascular disease risk factors. When regrouping individuals based on more intensive SBP control, individuals with levels <120 mm Hg outperformed individuals with higher SBP on verbal fluency regardless of adjustments (P < 0.01). More intensive rather than currently recommended levels of control associated with higher verbal fluency performance regardless of adjustments (P < 0.05). Individual cognitive test scores related to distinct SBP management with more intensive management appearing more robust against confounders. While cognitive associations with hypertension in Hispanics/Latinos may be multifactorial, different levels of SBP control should be considered in future prospective intervention studies. © American Journal of Hypertension, Ltd 2017. All rights reserved. For Permissions, please email: journals.permissions@oup.com

Finding the music of speech: Musical knowledge influences pitch processing in speech.

PubMed

Vanden Bosch der Nederlanden, Christina M; Hannon, Erin E; Snyder, Joel S

2015-10-01

Few studies comparing music and language processing have adequately controlled for low-level acoustical differences, making it unclear whether differences in music and language processing arise from domain-specific knowledge, acoustic characteristics, or both. We controlled acoustic characteristics by using the speech-to-song illusion, which often results in a perceptual transformation to song after several repetitions of an utterance. Participants performed a same-different pitch discrimination task for the initial repetition (heard as speech) and the final repetition (heard as song). Better detection was observed for pitch changes that violated rather than conformed to Western musical scale structure, but only when utterances transformed to song, indicating that music-specific pitch representations were activated and influenced perception. This shows that music-specific processes can be activated when an utterance is heard as song, suggesting that the high-level status of a stimulus as either language or music can be behaviorally dissociated from low-level acoustic factors. Copyright © 2015 Elsevier B.V. All rights reserved.

Distributed Scene Analysis For Autonomous Road Vehicle Guidance

NASA Astrophysics Data System (ADS)

Mysliwetz, Birger D.; Dickmanns, E. D.

1987-01-01

An efficient distributed processing scheme has been developed for visual road boundary tracking by 'VaMoRs', a testbed vehicle for autonomous mobility and computer vision. Ongoing work described here is directed to improving the robustness of the road boundary detection process in the presence of shadows, ill-defined edges and other disturbing real world effects. The system structure and the techniques applied for real-time scene analysis are presented along with experimental results. All subfunctions of road boundary detection for vehicle guidance, such as edge extraction, feature aggregation and camera pointing control, are executed in parallel by an onboard multiprocessor system. On the image processing level local oriented edge extraction is performed in multiple 'windows', tighly controlled from a hierarchically higher, modelbased level. The interpretation process involving a geometric road model and the observer's relative position to the road boundaries is capable of coping with ambiguity in measurement data. By using only selected measurements to update the model parameters even high noise levels can be dealt with and misleading edges be rejected.

Inverted-U shaped dopamine actions on human working memory and cognitive control

PubMed Central

Cools, R; D’Esposito, M

2011-01-01

Brain dopamine has long been implicated in cognitive control processes, including working memory. However, the precise role of dopamine in cognition is not well understood, partly because there is large variability in the response to dopaminergic drugs both across different behaviors and across different individuals. We review evidence from a series of studies with experimental animals, healthy humans and patients with Parkinson’s disease, which highlight two important factors that contribute to this large variability. First, the existence of an optimum dopamine level for cognitive function implicates the need to take into account baseline levels of dopamine when isolating dopamine’s effects. Second, cognitive control is a multi-factorial phenomenon, requiring a dynamic balance between cognitive stability and cognitive flexibility. These distinct components might implicate the prefrontal cortex and the striatum respectively. Manipulating dopamine will thus have paradoxical consequences for distinct cognitive control processes depending on distinct basal or optimal levels of dopamine in different brain regions. PMID:21531388

Microeconomics of process control in semiconductor manufacturing

NASA Astrophysics Data System (ADS)

Monahan, Kevin M.

2003-06-01

Process window control enables accelerated design-rule shrinks for both logic and memory manufacturers, but simple microeconomic models that directly link the effects of process window control to maximum profitability are rare. In this work, we derive these links using a simplified model for the maximum rate of profit generated by the semiconductor manufacturing process. We show that the ability of process window control to achieve these economic objectives may be limited by variability in the larger manufacturing context, including measurement delays and process variation at the lot, wafer, x-wafer, x-field, and x-chip levels. We conclude that x-wafer and x-field CD control strategies will be critical enablers of density, performance and optimum profitability at the 90 and 65nm technology nodes. These analyses correlate well with actual factory data and often identify millions of dollars in potential incremental revenue and cost savings. As an example, we show that a scatterometry-based CD Process Window Monitor is an economically justified, enabling technology for the 65nm node.

Criticality Safety Evaluation for Small Sample Preparation and Non-Destructive Assay (NDA) Operations in Wing 7 Basement of the CMR Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kunkle, Paige Elizabeth; Zhang, Ning

Nuclear Criticality Safety (NCS) has reviewed the fissionable material small sample preparation and NDA operations in Wing 7 Basement of the CMR Facility. This is a Level-1 evaluation conducted in accordance with NCS-AP-004 [Reference 1], formerly NCS-GUIDE-01, and the guidance set forth on use of the Standard Criticality Safety Requirements (SCSRs) [Reference 2]. As stated in Reference 2, the criticality safety evaluation consists of both the SCSR CSED and the SCSR Application CSED. The SCSR CSED is a Level-3 CSED [Reference 3]. This Level-1 CSED is the SCSR Application CSED. This SCSR Application (Level-1) evaluation does not derive controls, itmore » simply applies controls derived from the SCSR CSED (Level-3) for the application of operations conducted here. The controls derived in the SCSR CSED (Level-3) were evaluated via the process described in Section 6.6.5 of SD-130 (also reproduced in Section 4.3.5 of NCS-AP-004 [Reference 1]) and were determined to not meet the requirements for consideration of elevation into the safety basis documentation for CMR. According to the guidance set forth on use of the SCSRs [Reference 2], the SCSR CSED (Level-3) is also applicable to the CMR Facility because the process and the normal and credible abnormal conditions in question are bounded by those that are described in the SCSR CSED. The controls derived in the SCSR CSED include allowances for solid materials and solution operations. Based on the operations conducted at this location, there are less-than-accountable (LTA) amounts of 233U. Based on the evaluation documented herein, the normal and credible abnormal conditions that might arise during the execution of this process will remain subcritical with the following recommended controls.« less

A senior manufacturing laboratory for determining injection molding process capability

NASA Technical Reports Server (NTRS)

Wickman, Jerry L.; Plocinski, David

1992-01-01

The following is a laboratory experiment designed to further understanding of materials science. This subject material is directed at an upper level undergraduate/graduate student in an Engineering or Engineering Technology program. It is assumed that the student has a thorough understanding of the process and quality control. The format of this laboratory does not follow that which is normally recommended because of the nature of process capability and that of the injection molding equipment and tooling. This laboratory is instead developed to be used as a point of departure for determining process capability for any process in either a quality control laboratory or a manufacturing environment where control charts, process capability, and experimental or product design are considered important topics.

Learning and strain among newcomers: a three-wave study on the effects of job demands and job control.

PubMed

Taris, Toon W; Feij, Jan A

2004-11-01

The present 3-wave longitudinal study was an examination of job-related learning and strain as a function of job demand and job control. The participants were 311 newcomers to their jobs. On the basis of R. A. Karasek and T. Theorell's (1990) demand-control model, the authors predicted that high demand and high job control would lead to high levels of learning; low demand and low job control should lead to low levels of learning; high demand and low job control should lead to high levels of strain; and low demand and high job control should lead to low levels of strain. The relation between strain and learning was also examined. The authors tested the hypotheses using ANCOVA and structural equation modeling. The results revealed that high levels of strain have an adverse effect on learning; the reverse effect was not confirmed. It appears that Karasek and Theorell's model is very relevant when examining work socialization processes.

A Joint Learning Activity in Process Control and Distance Collaboration between Future Engineers and Technicians

ERIC Educational Resources Information Center

Deschênes, Jean-Sebastien; Barka, Noureddine; Michaud, Mario; Paradis, Denis; Brousseau, Jean

2013-01-01

A joint learning activity in process control is presented, in the context of a distance collaboration between engineering and technical-level students, in a similar fashion as current practices in the industry involving distance coordination and troubleshooting. The necessary infrastructure and the setup used are first detailed, followed by a…

Revealing List-Level Control in the Stroop Task by Uncovering Its Benefits and a Cost

ERIC Educational Resources Information Center

Bugg, Julie M.; McDaniel, Mark A.; Scullin, Michael K.; Braver, Todd S.

2011-01-01

Interference is reduced in mostly incongruent relative to mostly congruent lists. Classic accounts of this list-wide proportion congruence effect assume that list-level control processes strategically modulate word reading. Contemporary accounts posit that reliance on the word is modulated poststimulus onset by item-specific information (e.g.,…

Motivation as a Method of Controlling the Social Subject Self-Learning

ERIC Educational Resources Information Center

Isaev, Andrey V.; Kravets, Alla G.; Isaeva, Ludmila A.

2014-01-01

The paper substantiates inertial nature of the motivation system impact on the individual. Such exposure is a major shift from the level of motivational signs of external perception on the level of the individual internal motivation system. This approach justifies the ability to control the quality of the individual education as in the process of…

CNK1: A New Component in the Control of Insulin Signaling | Center for Cancer Research

Cancer.gov

The control of insulin release after a meal to mediate blood-glucose levels is an essential step in energy regulation. An external signal activates molecular pathways within the cell to control this process.

Neural bases of a specific strategy for visuospatial processing in rugby players.

PubMed

Sekiguchi, Atsushi; Yokoyama, Satoru; Kasahara, Satoshi; Yomogida, Yukihito; Takeuchi, Hikaru; Ogawa, Takeshi; Taki, Yasuyuki; Niwa, Shin-Ichi; Kawashima, Ryuta

2011-10-01

Rugby is one of the most tactically complex sports. Rugby coaching theory suggests that rugby players need to possess various cognitive abilities. A previous study claimed that rugby players have high visuospatial awareness, which is induced by a strategy described as taking a "bird's eye view." To examine if there were differential cortical networks related to visuospatial processing tasks among top-level rugby players and control novices, we compared brain activities during a visuospatial processing task between 20 male top-level rugby players (Top) and 20 control novice males (Novice) using functional magnetic resonance imaging (fMRI). To avoid the effect of differential behavioral performances on brain activation, we recruited novices whose visuospatial ability was expected to match that of the rugby players. We adopted a 3-D mental rotation task during fMRI scanning as a visuospatial processing task. Significantly greater activations from baseline were observed for the Top group than for the Novice group in the right superior parietal lobe and lateral occipital cortex. Significantly greater deactivations from baseline were observed for the Top group than for the Novice group in the right medial prefrontal cortex. The discrepancy between psychobehavioral outputs and the fMRI results suggested the existence of a cognitive strategy among top-level rugby players that differs from that among control novices. The greater activation of the right superior parietal lobe and lateral occipital cortex in top-level rugby players suggested a strategy involving visuospatial cognitive processing with respect to the bird's eye view. In addition, the right medial prefrontal cortex is known to be a part of the default mode networks, suggesting an additional cognitive load for the Top group when using the bird's-eye-view strategy. This further supported the existence of a specific cognitive strategy among top-level rugby players.

Levels-of-processing effect on internal source monitoring in schizophrenia

PubMed Central

RAGLAND, J. DANIEL; McCARTHY, ERIN; BILKER, WARREN B.; RENSINGER, COLLEEN M. B; VALDEZ, JEFFREY; KOHLER, CHRISTIAN; GUR, RAQUEL E.; GUR, RUBEN C.

2015-01-01

Background Recognition can be normalized in schizophrenia by providing patients with semantic organizational strategies through a levels-of-processing (LOP) framework. However, patients may rely primarily on familiarity effects, making recognition less sensitive than source monitoring to the strength of the episodic memory trace. The current study investigates whether providing semantic organizational strategies can also normalize patients’ internal source-monitoring performance. Method Sixteen clinically stable medicated patients with schizophrenia and 15 demographically matched healthy controls were asked to identify the source of remembered words following an LOP-encoding paradigm in which they alternated between processing words on a ‘shallow’ perceptual versus a ‘deep’ semantic level. A multinomial analysis provided orthogonal measures of item recognition and source discrimination, and bootstrapping generated variance to allow for parametric analyses. LOP and group effects were tested by contrasting recognition and source-monitoring parameters for words that had been encoded during deep versus shallow processing conditions. Results As in a previous study there were no group differences in LOP effects on recognition performance, with patients and controls benefiting equally from deep versus shallow processing. Although there were no group differences in internal source monitoring, only controls had significantly better performance for words processed during the deep encoding condition. Patient performance did not correlate with clinical symptoms or medication dose. Conclusions Providing a deep processing semantic encoding strategy significantly improved patients’ recognition performance only. The lack of a significant LOP effect on internal source monitoring in patients may reffect subtle problems in the relational binding of semantic information that are independent of strategic memory processes. PMID:16608558

Levels-of-processing effect on internal source monitoring in schizophrenia.

PubMed

Ragland, J Daniel; McCarthy, Erin; Bilker, Warren B; Brensinger, Colleen M; Valdez, Jeffrey; Kohler, Christian; Gur, Raquel E; Gur, Ruben C

2006-05-01

Recognition can be normalized in schizophrenia by providing patients with semantic organizational strategies through a levels-of-processing (LOP) framework. However, patients may rely primarily on familiarity effects, making recognition less sensitive than source monitoring to the strength of the episodic memory trace. The current study investigates whether providing semantic organizational strategies can also normalize patients' internal source-monitoring performance. Sixteen clinically stable medicated patients with schizophrenia and 15 demographically matched healthy controls were asked to identify the source of remembered words following an LOP-encoding paradigm in which they alternated between processing words on a 'shallow' perceptual versus a 'deep' semantic level. A multinomial analysis provided orthogonal measures of item recognition and source discrimination, and bootstrapping generated variance to allow for parametric analyses. LOP and group effects were tested by contrasting recognition and source-monitoring parameters for words that had been encoded during deep versus shallow processing conditions. As in a previous study there were no group differences in LOP effects on recognition performance, with patients and controls benefiting equally from deep versus shallow processing. Although there were no group differences in internal source monitoring, only controls had significantly better performance for words processed during the deep encoding condition. Patient performance did not correlate with clinical symptoms or medication dose. Providing a deep processing semantic encoding strategy significantly improved patients' recognition performance only. The lack of a significant LOP effect on internal source monitoring in patients may reflect subtle problems in the relational binding of semantic information that are independent of strategic memory processes.

A neo-strategic planning approach to enhance local tobacco control programs.

PubMed

Douglas, Malinda R; Carter, Sara Sally R; Wilson, Andrew P; Chan, Andie

2015-01-01

Research in tobacco control demonstrating best practices is widely disseminated; however, application at the local level is often difficult. Translating research into practice requires a concerted effort to develop an understanding of the evidence and how it can be applied within diverse contexts. A strategic planning infrastructure was developed to support the translation of evidence-based interventions into community practice. This paper highlights the strategic process of turning "know-what" into "know-how" to facilitate the strategic planning and implementation of tobacco control best practices at the local level. The purpose, people, process, and product strategies of knowledge management and translation provided a framework for the strategic planning infrastructure. The knowledge translation concepts of audience, motivations, and mechanisms were synergized in the neo-strategic planning component design. The participants were 20 community coalitions funded to implement local tobacco control programs. From 2004 to 2011, the strategic planners facilitated a cyclical process to translate research into practice using a trio of integrated tools, skill-building workshops on strategic planning, and grantee-driven technical assistance and consultation. In the short term, the usefulness of the strategic planning components to the programs was measured. The intermediate outcome was the successful movement of the community programs from the planning stage to the implementation stage. The achievement of community-level changes in planned tobacco control efforts was the overall outcome measure for the success of the local coalitions. Seventeen of 20 communities that began the planning process implemented strategic plans. All 17 of the programs implemented evidence-based practices, resulting in numerous tobacco-free policies, increased cessation, and increased support from the media and community. Bridging the gap between research and practice can enhance the practicality, efficiency, and effectiveness of tobacco control programs at the local level, maximizing the potential positive health impact. Copyright © 2015 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

An approach to quality and performance control in a computer-assisted clinical chemistry laboratory.

PubMed Central

Undrill, P E; Frazer, S C

1979-01-01

A locally developed, computer-based clinical chemistry laboratory system has been in operation since 1970. This utilises a Digital Equipment Co Ltd PDP 12 and an interconnected PDP 8/F computer. Details are presented of the performance and quality control techniques incorporated into the system. Laboratory performance is assessed through analysis of results from fixed-level control sera as well as from cumulative sum methods. At a simple level the presentation may be considered purely indicative, while at a more sophisticated level statistical concepts have been introduced to aid the laboratory controller in decision-making processes. PMID:438340

Influence of motivation on control hierarchy in the human frontal cortex.

PubMed

Bahlmann, Jörg; Aarts, Esther; D'Esposito, Mark

2015-02-18

The frontal cortex mediates cognitive control and motivation to shape human behavior. It is generally observed that medial frontal areas are involved in motivational aspects of behavior, whereas lateral frontal regions are involved in cognitive control. Recent models of cognitive control suggest a rostro-caudal gradient in lateral frontal regions, such that progressively more rostral (anterior) regions process more complex aspects of cognitive control. How motivation influences such a control hierarchy is still under debate. Although some researchers argue that both systems work in parallel, others argue in favor of an interaction between motivation and cognitive control. In the latter case it is yet unclear how motivation would affect the different levels of the control hierarchy. This was investigated in the present functional MRI study applying different levels of cognitive control under different motivational states (low vs high reward anticipation). Three levels of cognitive control were tested by varying rule complexity: stimulus-response mapping (low-level), flexible task updating (mid-level), and sustained cue-task associations (high-level). We found an interaction between levels of cognitive control and motivation in medial and lateral frontal subregions. Specifically, flexible updating (mid-level of control) showed the strongest beneficial effect of reward and only this level exhibited functional coupling between dopamine-rich midbrain regions and the lateral frontal cortex. These findings suggest that motivation differentially affects the levels of a control hierarchy, influencing recruitment of frontal cortical control regions depending on specific task demands. Copyright © 2015 the authors 0270-6474/15/353207-11$15.00/0.

Three-level sampler having automated thresholds

NASA Technical Reports Server (NTRS)

Jurgens, R. F.

1976-01-01

A three-level sampler is described that has its thresholds controlled automatically so as to track changes in the statistics of the random process being sampled. In particular, the mean value is removed and the ratio of the standard deviation of the random process to the threshold is maintained constant. The system is configured in such a manner that slow drifts in the level comparators and digital-to-analog converters are also removed. The ratio of the standard deviation to threshold level may be chosen within the constraints of the ratios of two integers N and M. These may be chosen to minimize the quantizing noise of the sampled process.

Neuropsychological Characteristics and Their Association with Higher-Level Functional Capacity in Parkinson's Disease

PubMed Central

Miura, Kayoko; Matsui, Mie; Takashima, Shutaro; Tanaka, Kortaro

2015-01-01

Background/Aims Little is known about the relationship between cognitive functions and higher-level functional capacity (e.g. intellectual activity, social role, and social participation) in Parkinson's disease (PD). The purpose of this study was to clarify neuropsychological characteristics and their association with higher-level functional capacity in PD patients. Methods Participants were 31 PD patients and 23 demographically matched healthy controls. Neuropsychological tests were conducted. One year later, a questionnaire survey evaluated higher-level functional capacity in daily living. Results The PD group scored significantly lower than the control group in all cognitive domains, particularly executive function and processing. Executive function, processing speed, language, and memory were significantly correlated with higher-level functional capacity in PD patients. Stepwise regression showed that only executive function (Trail Making Test-B), together with disease severity (HY stage), predicted the higher-level functional capacity. Conclusion Our findings provide evidence of a relationship between executive function and higher-level functional capacity in patients with PD. PMID:26273243

Distributed systems status and control

NASA Technical Reports Server (NTRS)

Kreidler, David; Vickers, David

1990-01-01

Concepts are investigated for an automated status and control system for a distributed processing environment. System characteristics, data requirements for health assessment, data acquisition methods, system diagnosis methods and control methods were investigated in an attempt to determine the high-level requirements for a system which can be used to assess the health of a distributed processing system and implement control procedures to maintain an accepted level of health for the system. A potential concept for automated status and control includes the use of expert system techniques to assess the health of the system, detect and diagnose faults, and initiate or recommend actions to correct the faults. Therefore, this research included the investigation of methods by which expert systems were developed for real-time environments and distributed systems. The focus is on the features required by real-time expert systems and the tools available to develop real-time expert systems.

Systems and methods for interactive virtual reality process control and simulation

DOEpatents

Daniel, Jr., William E.; Whitney, Michael A.

2001-01-01

A system for visualizing, controlling and managing information includes a data analysis unit for interpreting and classifying raw data using analytical techniques. A data flow coordination unit routes data from its source to other components within the system. A data preparation unit handles the graphical preparation of the data and a data rendering unit presents the data in a three-dimensional interactive environment where the user can observe, interact with, and interpret the data. A user can view the information on various levels, from a high overall process level view, to a view illustrating linkage between variables, to view the hard data itself, or to view results of an analysis of the data. The system allows a user to monitor a physical process in real-time and further allows the user to manage and control the information in a manner not previously possible.

The NIST Real-Time Control System (RCS): A Reference Model Architecture for Computational Intelligence

NASA Technical Reports Server (NTRS)

Albus, James S.

1996-01-01

The Real-time Control System (RCS) developed at NIST and elsewhere over the past two decades defines a reference model architecture for design and analysis of complex intelligent control systems. The RCS architecture consists of a hierarchically layered set of functional processing modules connected by a network of communication pathways. The primary distinguishing feature of the layers is the bandwidth of the control loops. The characteristic bandwidth of each level is determined by the spatial and temporal integration window of filters, the temporal frequency of signals and events, the spatial frequency of patterns, and the planning horizon and granularity of the planners that operate at each level. At each level, tasks are decomposed into sequential subtasks, to be performed by cooperating sets of subordinate agents. At each level, signals from sensors are filtered and correlated with spatial and temporal features that are relevant to the control function being implemented at that level.

Systems Factorial Technology provides new insights on global-local information processing in autism spectrum disorders.

PubMed

Johnson, Shannon A; Blaha, Leslie M; Houpt, Joseph W; Townsend, James T

2010-02-01

Previous studies of global-local processing in autism spectrum disorders (ASDs) have indicated mixed findings, with some evidence of a local processing bias, or preference for detail-level information, and other results suggesting typical global advantage, or preference for the whole or gestalt. Findings resulting from this paradigm have been used to argue for or against a detail focused processing bias in ASDs, and thus have important theoretical implications. We applied Systems Factorial Technology, and the associated Double Factorial Paradigm (both defined in the text), to examine information processing characteristics during a divided attention global-local task in high-functioning individuals with an ASD and typically developing controls. Group data revealed global advantage for both groups, contrary to some current theories of ASDs. Information processing models applied to each participant revealed that task performance, although showing no differences at the group level, was supported by different cognitive mechanisms in ASD participants compared to controls. All control participants demonstrated inhibitory parallel processing and the majority demonstrated a minimum-time stopping rule. In contrast, ASD participants showed exhaustive parallel processing with mild facilitatory interactions between global and local information. Thus our results indicate fundamental differences in the stopping rules and channel dependencies in individuals with an ASD.

Dynamic response characteristics analysis of the doubly-fed wind power system under grid voltage drop

NASA Astrophysics Data System (ADS)

Chen, Y.; Wang, J.; Wang, H. H.; Yang, L.; Chen, W.; Xu, Y. T.

2016-08-01

Double-fed induction generator (DFIG) is sensitive to the disturbances of grid, so the security and stability of the grid and the DFIG itself are under threat with the rapid increase of DFIG. Therefore, it is important to study dynamic response of the DFIG when voltage drop failure is happened in power system. In this paper, firstly, mathematical models and the control strategy about mechanical and electrical response processes is respectively introduced. Then through the analysis of response process, it is concluded that the dynamic response characteristics are related to voltage drop level, operating status of DFIG and control strategy adapted to rotor side. Last, the correctness of conclusion is validated by the simulation about mechanical and electrical response processes in different voltage levels drop and different DFIG output levels under DIgSILENT/PowerFactory software platform.

Real time monitoring of powder blend bulk density for coupled feed-forward/feed-back control of a continuous direct compaction tablet manufacturing process.

PubMed

Singh, Ravendra; Román-Ospino, Andrés D; Romañach, Rodolfo J; Ierapetritou, Marianthi; Ramachandran, Rohit

2015-11-10

The pharmaceutical industry is strictly regulated, where precise and accurate control of the end product quality is necessary to ensure the effectiveness of the drug products. For such control, the process and raw materials variability ideally need to be fed-forward in real time into an automatic control system so that a proactive action can be taken before it can affect the end product quality. Variations in raw material properties (e.g., particle size), feeder hopper level, amount of lubrication, milling and blending action, applied shear in different processing stages can affect the blend density significantly and thereby tablet weight, hardness and dissolution. Therefore, real time monitoring of powder bulk density variability and its incorporation into the automatic control system so that its effect can be mitigated proactively and efficiently is highly desired. However, real time monitoring of powder bulk density is still a challenging task because of different level of complexities. In this work, powder bulk density which has a significant effect on the critical quality attributes (CQA's) has been monitored in real time in a pilot-plant facility, using a NIR sensor. The sensitivity of the powder bulk density on critical process parameters (CPP's) and CQA's has been analyzed and thereby feed-forward controller has been designed. The measured signal can be used for feed-forward control so that the corrective actions on the density variations can be taken before they can influence the product quality. The coupled feed-forward/feed-back control system demonstrates improved control performance and improvements in the final product quality in the presence of process and raw material variations. Copyright © 2015 Elsevier B.V. All rights reserved.

40 CFR 63.503 - Emissions averaging provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... used in conjunction with other controls for a Group 1 storage vessel, batch front-end process vent... will be allowed only for the increase in control after November 15, 1990. (2) Group 1 emission points... Group 1 emission points that are controlled to a level less stringent than the reference control...

40 CFR 63.503 - Emissions averaging provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... used in conjunction with other controls for a Group 1 storage vessel, batch front-end process vent... will be allowed only for the increase in control after November 15, 1990. (2) Group 1 emission points... Group 1 emission points that are controlled to a level less stringent than the reference control...

40 CFR 63.503 - Emissions averaging provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... used in conjunction with other controls for a Group 1 storage vessel, batch front-end process vent... will be allowed only for the increase in control after November 15, 1990. (2) Group 1 emission points... Group 1 emission points that are controlled to a level less stringent than the reference control...

40 CFR 63.503 - Emissions averaging provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... used in conjunction with other controls for a Group 1 storage vessel, batch front-end process vent... will be allowed only for the increase in control after November 15, 1990. (2) Group 1 emission points... Group 1 emission points that are controlled to a level less stringent than the reference control...

40 CFR 63.503 - Emissions averaging provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... used in conjunction with other controls for a Group 1 storage vessel, batch front-end process vent... will be allowed only for the increase in control after November 15, 1990. (2) Group 1 emission points... Group 1 emission points that are controlled to a level less stringent than the reference control...

A critical role of temporoparietal junction in the integration of top-down and bottom-up attentional control

PubMed Central

Wu, Qiong; Chang, Chi-Fu; Xi, Sisi; Huang, I-Wen; Liu, Zuxiang; Juan, Chi-Hung; Wu, Yanhong; Fan, Jin

2015-01-01

Information processing can be biased toward behaviorally relevant and salient stimuli by top-down (goal-directed) and bottom-up (stimulus-driven) attentional control processes. However, the neural basis underlying the integration of these processes is not well understood. We employed functional magnetic resonance imaging and transcranial direct-current stimulation (tDCS) in humans to examine the brain mechanisms underlying the interaction between these two processes. We manipulated the cognitive load involved in top-down processing and stimulus surprise involved in bottom-up processing in a factorial design by combining a majority function task and an oddball paradigm. We found that high cognitive load and high surprise level were associated with prolonged reaction time compared to low cognitive load and low surprise level, with a synergistic interaction effect which was accompanied by a greater deactivation of bilateral temporoparietal junction (TPJ). In addition, the TPJ displayed negative functional connectivity with right middle occipital gyrus involved in bottom-up processing (modulated by the interaction effect) and the right frontal eye field (FEF) involved in top-down control. The enhanced negative functional connectivity between the TPJ and right FEF was accompanied by a larger behavioral interaction effect across subjects. Application of cathodal tDCS over the right TPJ eliminated the interaction effect. These results suggest that the TPJ plays a critical role in processing bottom-up information for top-down control of attention. PMID:26308973

"A manager in the minds of doctors:" a comparison of new modes of control in European hospitals.

PubMed

Kuhlmann, Ellen; Burau, Viola; Correia, Tiago; Lewandowski, Roman; Lionis, Christos; Noordegraaf, Mirko; Repullo, Jose

2013-07-02

Hospital governance increasingly combines management and professional self-governance. This article maps the new emergent modes of control in a comparative perspective and aims to better understand the relationship between medicine and management as hybrid and context-dependent. Theoretically, we critically review approaches into the managerialism-professionalism relationship; methodologically, we expand cross-country comparison towards the meso-level of organisations; and empirically, the focus is on processes and actors in a range of European hospitals. The research is explorative and was carried out as part of the FP7 COST action IS0903 Medicine and Management, Working Group 2. Comprising seven European countries, the focus is on doctors and public hospitals. We use a comparative case study design that primarily draws on expert information and document analysis as well as other secondary sources. The findings reveal that managerial control is not simply an external force but increasingly integrated in medical professionalism. These processes of change are relevant in all countries but shaped by organisational settings, and therefore create different patterns of control: (1) 'integrated' control with high levels of coordination and coherent patterns for cost and quality controls; (2) 'partly integrated' control with diversity of coordination on hospital and department level and between cost and quality controls; and (3) 'fragmented' control with limited coordination and gaps between quality control more strongly dominated by medicine, and cost control by management. Our comparison highlights how organisations matter and brings the crucial relevance of 'coordination' of medicine and management across the levels (hospital/department) and the substance (cost/quality-safety) of control into perspective. Consequently, coordination may serve as a taxonomy of emergent modes of control, thus bringing new directions for cost-efficient and quality-effective hospital governance into perspective.

10 CFR 72.158 - Control of special processes.

Code of Federal Regulations, 2013 CFR

2013-01-01

... NUCLEAR FUEL, HIGH-LEVEL RADIOACTIVE WASTE, AND REACTOR-RELATED GREATER THAN CLASS C WASTE Quality..., and applicant for a CoC shall establish measures to ensure that special processes, including welding...

10 CFR 72.158 - Control of special processes.

Code of Federal Regulations, 2011 CFR

2011-01-01

... NUCLEAR FUEL, HIGH-LEVEL RADIOACTIVE WASTE, AND REACTOR-RELATED GREATER THAN CLASS C WASTE Quality..., and applicant for a CoC shall establish measures to ensure that special processes, including welding...

10 CFR 72.158 - Control of special processes.

Code of Federal Regulations, 2012 CFR

2012-01-01

... NUCLEAR FUEL, HIGH-LEVEL RADIOACTIVE WASTE, AND REACTOR-RELATED GREATER THAN CLASS C WASTE Quality..., and applicant for a CoC shall establish measures to ensure that special processes, including welding...

10 CFR 72.158 - Control of special processes.

Code of Federal Regulations, 2014 CFR

2014-01-01

... NUCLEAR FUEL, HIGH-LEVEL RADIOACTIVE WASTE, AND REACTOR-RELATED GREATER THAN CLASS C WASTE Quality..., and applicant for a CoC shall establish measures to ensure that special processes, including welding...

Creativity and cognitive control: Behavioral and ERP evidence that divergent thinking, but not real-life creative achievement, relates to better cognitive control.

PubMed

Zabelina, Darya L; Ganis, Giorgio

2018-02-13

Two studies used event-related potentials (ERPs) to examine whether and how divergent thinking and creative achievement are linked to attentional flexibility and cognitive control as indexed by response times and by the amplitude of the anterior N2 ERP component. Both experiments used an oddball paradigm in which participants viewed hierarchical letter stimuli and identified target letters in frequent and rare target trials. The successful identification of targets required attentional flexibility when switching levels of attention (from the frequent global to the rare local attentional level, or vice-versa). Divergent thinkers showed smaller switching times on rare target trials, indicating higher levels of attentional flexibility. Furthermore, divergent thinkers engaged cognitive control processes more strongly at the moment of the attentional switch (and before the response), as indicated by a larger N2 difference between frequent and rare targets. In contrast, creative achievement was associated neither with the switching times on rare target trials, nor with a larger N2 difference between frequent and rare targets. All results held when controlling for general intelligence. Results from these studies provide evidence that divergent thinking is associated with higher attentional flexibility and that such attentional flexibility relies on cognitive control processes required when disengaging from one level of attention (e.g., global), and shifting to the other level of attention (e.g., local). Copyright © 2018 Elsevier Ltd. All rights reserved.

Automated control of hierarchical systems using value-driven methods

NASA Technical Reports Server (NTRS)

Pugh, George E.; Burke, Thomas E.

1990-01-01

An introduction is given to the Value-driven methodology, which has been successfully applied to solve a variety of difficult decision, control, and optimization problems. Many real-world decision processes (e.g., those encountered in scheduling, allocation, and command and control) involve a hierarchy of complex planning considerations. For such problems it is virtually impossible to define a fixed set of rules that will operate satisfactorily over the full range of probable contingencies. Decision Science Applications' value-driven methodology offers a systematic way of automating the intuitive, common-sense approach used by human planners. The inherent responsiveness of value-driven systems to user-controlled priorities makes them particularly suitable for semi-automated applications in which the user must remain in command of the systems operation. Three examples of the practical application of the approach in the automation of hierarchical decision processes are discussed: the TAC Brawler air-to-air combat simulation is a four-level computerized hierarchy; the autonomous underwater vehicle mission planning system is a three-level control system; and the Space Station Freedom electrical power control and scheduling system is designed as a two-level hierarchy. The methodology is compared with rule-based systems and with other more widely-known optimization techniques.

Signal transduction and oxidative processes in sinonasal polyposis.

PubMed

Cannady, Steven B; Batra, Pete S; Leahy, Rachel; Citardi, Martin J; Janocha, Allison; Ricci, Kristin; Comhair, Suzy A A; Bodine, Melanie; Wang, Zeneng; Hazen, Stanley L; Erzurum, Serpil C

2007-12-01

Nasal polyposis is characterized by impaired regulation of nasal tissue growth and is associated with chronic inflammation, sinus infections, and low levels of nitric oxide (NO). Based on its critical role in mediating cell growth and antimicrobial function, decrease of NO levels has been implicated in the pathogenesis of nasal polyposis. We sought to evaluate mechanisms for the low NO level in polyposis, including factors regulating NO synthase (NOS) expression and activity and NO consumptive processes in nasal epithelial cells and nasal lavage fluid. Eighteen patients with nasal polyposis and 8 healthy control subjects were studied. Nasal brushings, nasal lavage fluid, and nasal biopsy specimens were collected and analyzed. NO metabolite levels (nitrite and nitrate) in nasal lavage fluid from patients with polyps were less than those in control subjects, but activation of signal transduction and inducer of transcription 1, which regulates inducible NOS gene expression and protein expression, was present at higher levels in polyp than in healthy control tissue. Levels of arginine, methylarginine, and endogenous NOS inhibitors were similar between polyp and control tissue. In contrast, superoxide dismutase activity of polyp tissues was lower than that seen in control tissue and associated with increased nitrotyrosine, a biomarker of oxidant consumptive products of NO. Taken together, these data suggest that the nasal polyp environment is characterized by abnormalities in NO metabolism that might predispose to altered regulation of tissue growth and infection. Identification of NO metabolic abnormalities might lead to novel treatments for sinonasal polyposis targeted against the pathways identified within this study.

Automated Subsystem Control for Life Support System (ASCLSS)

NASA Technical Reports Server (NTRS)

Block, Roger F.

1987-01-01

The Automated Subsystem Control for Life Support Systems (ASCLSS) program has successfully developed and demonstrated a generic approach to the automation and control of space station subsystems. The automation system features a hierarchical and distributed real-time control architecture which places maximum controls authority at the lowest or process control level which enhances system autonomy. The ASCLSS demonstration system pioneered many automation and control concepts currently being considered in the space station data management system (DMS). Heavy emphasis is placed on controls hardware and software commonality implemented in accepted standards. The approach demonstrates successfully the application of real-time process and accountability with the subsystem or process developer. The ASCLSS system completely automates a space station subsystem (air revitalization group of the ASCLSS) which moves the crew/operator into a role of supervisory control authority. The ASCLSS program developed over 50 lessons learned which will aide future space station developers in the area of automation and controls..

A case-control study on association of proteasome subunit beta 8 (PSMB8) and transporter associated with antigen processing 1 (TAP1) polymorphisms and their transcript levels in vitiligo from Gujarat.

PubMed

Jadeja, Shahnawaz D; Mansuri, Mohmmad Shoab; Singh, Mala; Dwivedi, Mitesh; Laddha, Naresh C; Begum, Rasheedunnisa

2017-01-01

Autoimmunity has been implicated in the destruction of melanocytes from vitiligo skin. Major histocompatibility complex (MHC) class-II linked genes proteasome subunit beta 8 (PSMB8) and transporter associated with antigen processing 1 (TAP1), involved in antigen processing and presentation have been reported to be associated with several autoimmune diseases including vitiligo. To explore PSMB8 rs2071464 and TAP1 rs1135216 single nucleotide polymorphisms and to estimate the expression of PSMB8 and TAP1 in patients with vitiligo and unaffected controls from Gujarat. PSMB8 rs2071464 polymorphism was genotyped using polymerase chain reaction- restriction fragment length polymorphism (PCR-RFLP) and TAP1 rs1135216 polymorphism was genotyped by amplification refractory mutation system-polymerase chain reaction (ARMS-PCR) in 378 patients with vitiligo and 509 controls. Transcript levels of PSMB8 and TAP1 were measured in the PBMCs of 91 patients and 96 controls by using qPCR. Protein levels of PSMB8 were also determined by Western blot analysis. The frequency of 'TT' genotype of PSMB8 polymorphism was significantly lowered in patients with generalized and active vitiligo (p = 0.019 and p = 0.005) as compared to controls suggesting its association with the activity of the disease. However, TAP1 polymorphism was not associated with vitiligo susceptibility. A significant decrease in expression of PSMB8 at both transcript level (p = 0.002) as well as protein level (p = 0.0460) was observed in vitiligo patients as compared to controls. No significant difference was observed between patients and controls for TAP1 transcripts (p = 0.553). Interestingly, individuals with the susceptible CC genotype of PSMB8 polymorphism showed significantly reduced PSMB8 transcript level as compared to that of CT and TT genotypes (p = 0.009 and p = 0.003 respectively). PSMB8 rs2071464 was associated with generalized and active vitiligo from Gujarat whereas TAP1 rs1135216 showed no association. The down-regulation of PSMB8 in patients with risk genotype 'CC' advocates the vital role of PSMB8 in the autoimmune basis of vitiligo.

[Study on "multi-dimensional structure and process dynamics quality control system" of Danshen infusion solution based on component structure theory].

PubMed

Feng, Liang; Zhang, Ming-Hua; Gu, Jun-Fei; Wang, Gui-You; Zhao, Zi-Yu; Jia, Xiao-Bin

2013-11-01

As traditional Chinese medicine (TCM) preparation products feature complex compounds and multiple preparation processes, the implementation of quality control in line with the characteristics of TCM preparation products provides a firm guarantee for the clinical efficacy and safety of TCM preparation products. Danshen infusion solution is a preparation commonly used in clinic, but its quality control is restricted to indexes of finished products, which can not guarantee its inherent quality. Our study group has proposed "multi-dimensional structure and process dynamics quality control system" on the basis of "component structure theory", for the purpose of controlling the quality of Danshen infusion solution at multiple levels and in multiple links from the efficacy-related material basis, the safety-related material basis, the characteristics of dosage form to the preparation process. This article, we bring forth new ideas and models to the quality control of TCM preparation products.

Preserved subliminal processing and impaired conscious access in schizophrenia

PubMed Central

Del Cul, Antoine; Dehaene, Stanislas; Leboyer, Marion

2006-01-01

Background Studies of visual backward masking have frequently revealed an elevated masking threshold in schizophrenia. This finding has frequently been interpreted as indicating a low-level visual deficit. However, more recent models suggest that masking may also involve late and higher-level integrative processes, while leaving intact early “bottom-up” visual processing. Objectives We tested the hypothesis that the backward masking deficit in schizophrenia corresponds to a deficit in the late stages of conscious perception, whereas the subliminal processing of masked stimuli is fully preserved. Method 28 patients with schizophrenia and 28 normal controls performed two backward-masking experiments. We used Arabic digits as stimuli and varied quasi-continuously the interval with a subsequent mask, thus allowing us to progressively “unmask” the stimuli. We finely quantified their degree of visibility using both objective and subjective measures to evaluate the threshold duration for access to consciousness. We also studied the priming effect caused by the variably masked numbers on a comparison task performed on a subsequently presented and highly visible target number. Results The threshold delay between digit and mask necessary for the conscious perception of the masked stimulus was longer in patients compared to control subjects. This higher consciousness threshold in patients was confirmed by an objective and a subjective measure, and both measures were highly correlated for patients as well as for controls. However, subliminal priming of masked numbers was effective and identical in patients compared to controls. Conclusions Access to conscious report of masked stimuli is impaired in schizophrenia, while fast bottom-up processing of the same stimuli, as assessed by subliminal priming, is preserved. These findings suggest a high-level origin of the masking deficit in schizophrenia, although they leave open for further research its exact relation to previously identified bottom-up visual processing abnormalities. PMID:17146006

Cognitive processes and attitudes in bipolar disorder: a study into personality, dysfunctional attitudes and attention bias in patients with bipolar disorder and their relatives.

PubMed

Jabben, Nienke; Arts, Baer; Jongen, Ellen M M; Smulders, Fren T Y; van Os, Jim; Krabbendam, Lydia

2012-12-20

Research in cognitive processes and attitudes in bipolar disorder is scarce and has provided mixed findings, possibly due to differences in current mood state. It is unclear whether alterations in cognitive processes and attitudes are only related to the depressive mood states of bipolar patients or also represent a vulnerability marker for the development of future (depressive) episodes. This was investigated in the current study. Both implicit (attentional bias for emotional words) and explicit (dysfunctional attitudes and personality characteristics) measures of cognitive processes and attitudes were assessed in 77 bipolar patients with varying levels of depressive symptoms (depressed=17, euthymic n=60), their healthy first-degree relatives (n=39) and a healthy control group (n=61). Analyses of variance were used to investigate differences between groups. Mildly depressed patients with bipolar disorder demonstrated an attentional bias away from positive emotional words and showed increased dysfunctional attitudes and higher levels of neuroticism. Euthymic patients were largely comparable to healthy controls and only differed from controls in higher levels of neuroticism. Relatives were similar to controls on all measures, although they significantly differed from bipolar patients in displaying less neuroticism and more extraversion. No firm conclusions regarding causality can be drawn from the associations that were found between cognitive processes and attitudes and the evolution of mood symptoms in bipolar disorder. Alterations in cognitive processes and attitudes in bipolar patients appear to be mostly related to the expression of mood symptomatology rather than to the vulnerability for bipolar disorder. Copyright © 2012 Elsevier B.V. All rights reserved.

Application of overlay modeling and control with Zernike polynomials in an HVM environment

NASA Astrophysics Data System (ADS)

Ju, JaeWuk; Kim, MinGyu; Lee, JuHan; Nabeth, Jeremy; Jeon, Sanghuck; Heo, Hoyoung; Robinson, John C.; Pierson, Bill

2016-03-01

Shrinking technology nodes and smaller process margins require improved photolithography overlay control. Generally, overlay measurement results are modeled with Cartesian polynomial functions for both intra-field and inter-field models and the model coefficients are sent to an advanced process control (APC) system operating in an XY Cartesian basis. Dampened overlay corrections, typically via exponentially or linearly weighted moving average in time, are then retrieved from the APC system to apply on the scanner in XY Cartesian form for subsequent lot exposure. The goal of the above method is to process lots with corrections that target the least possible overlay misregistration in steady state as well as in change point situations. In this study, we model overlay errors on product using Zernike polynomials with same fitting capability as the process of reference (POR) to represent the wafer-level terms, and use the standard Cartesian polynomials to represent the field-level terms. APC calculations for wafer-level correction are performed in Zernike basis while field-level calculations use standard XY Cartesian basis. Finally, weighted wafer-level correction terms are converted to XY Cartesian space in order to be applied on the scanner, along with field-level corrections, for future wafer exposures. Since Zernike polynomials have the property of being orthogonal in the unit disk we are able to reduce the amount of collinearity between terms and improve overlay stability. Our real time Zernike modeling and feedback evaluation was performed on a 20-lot dataset in a high volume manufacturing (HVM) environment. The measured on-product results were compared to POR and showed a 7% reduction in overlay variation including a 22% terms variation. This led to an on-product raw overlay Mean + 3Sigma X&Y improvement of 5% and resulted in 0.1% yield improvement.

Coherent and phase-sensitive phenomena of ultrashort laser pulses propagating in three-level {lambda}-type systems studied with the finite-difference time-domain method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loiko, Yurii; Institute of Molecular and Atomic Physics, National Academy of Sciences of Belarus, Nezaleznasty Ave. 70, 220072 Minsk; Serrat, Carles

2006-06-15

Propagation of single- and two-color hyperbolic secant femtosecond laser pulses in a three-level {lambda}-type quantum system is investigated by solving the Maxwell and density matrix equations with the finite-difference time-domain and Runge-Kutta methods. As a first study of our modeling, we simulate pulse self-induced transparency (SIT) in two-level systems and see how this phenomenon can be controlled by manipulating the initial relative phase between the SIT pulse and a second control pulse, provided the ratio between both pulse frequencies obeys the relation {omega}{sub 1}/{omega}{sub 2}=3. We then examine frequency down-conversion processes that are observed with single- and two-color pulses themore » envelope area of which is equal to or a multiple of 2{pi}, for pulse frequencies close to resonance with the transitions of a three-level {lambda} medium. Also, phase-sensitive phenomena are discussed in the case of two-color {omega}-3{omega} pulses propagating resonantly in the three-level system. In particular, possibilities for such coherent control are found for frequency down-conversion processes when the ratio of the frequencies of optical transitions is {omega}{sub 13}/{omega}{sub 12}=3. The conditions for quantum control of four-wave mixing processes are also examined when the pulse frequencies of two-color {omega}-3{omega} pulses are far from any resonance of the three-level system. We demonstrate the possibility to cancel the phase sensitivity of the four-wave coupling in a {lambda}-type system by competition effects between optical transitions.« less

In Support of a Distinction between Voluntary and Stimulus-Driven Control: A Review of the Literature on Proportion Congruent Effects.

PubMed

Bugg, Julie M; Crump, Matthew J C

2012-01-01

Cognitive control is by now a large umbrella term referring collectively to multiple processes that plan and coordinate actions to meet task goals. A common feature of paradigms that engage cognitive control is the task requirement to select relevant information despite a habitual tendency (or bias) to select goal-irrelevant information. At least since the 1970s, researchers have employed proportion congruent (PC) manipulations to experimentally establish selection biases and evaluate the mechanisms used to control attention. PC manipulations vary the frequency with which irrelevant information conflicts (i.e., is incongruent) with relevant information. The purpose of this review is to summarize the growing body of literature on PC effects across selective attention paradigms, beginning first with Stroop, and then describing parallel effects in flanker and task-switching paradigms. The review chronologically tracks the expansion of the PC manipulation from its initial implementation at the list-wide level, to more recent implementations at the item-specific and context-specific levels. An important theoretical aim is demonstrating that PC effects at different levels (e.g., list-wide vs. item or context-specific) support a distinction between voluntary forms of cognitive control, which operate based on anticipatory information, and relatively automatic or reflexive forms of cognitive control, which are rapidly triggered by the processing of particular stimuli or stimulus features. A further aim is to highlight those PC manipulations that allow researchers to dissociate stimulus-driven control from other stimulus-driven processes (e.g., S-R responding; episodic retrieval). We conclude by discussing the utility of PC manipulations for exploring the distinction between voluntary control and stimulus-driven control in other relevant paradigms.

Statistical Methods in Assembly Quality Management of Multi-Element Products on Automatic Rotor Lines

NASA Astrophysics Data System (ADS)

Pries, V. V.; Proskuriakov, N. E.

2018-04-01

To control the assembly quality of multi-element mass-produced products on automatic rotor lines, control methods with operational feedback are required. However, due to possible failures in the operation of the devices and systems of automatic rotor line, there is always a real probability of getting defective (incomplete) products into the output process stream. Therefore, a continuous sampling control of the products completeness, based on the use of statistical methods, remains an important element in managing the quality of assembly of multi-element mass products on automatic rotor lines. The feature of continuous sampling control of the multi-element products completeness in the assembly process is its breaking sort, which excludes the possibility of returning component parts after sampling control to the process stream and leads to a decrease in the actual productivity of the assembly equipment. Therefore, the use of statistical procedures for continuous sampling control of the multi-element products completeness when assembled on automatic rotor lines requires the use of such sampling plans that ensure a minimum size of control samples. Comparison of the values of the limit of the average output defect level for the continuous sampling plan (CSP) and for the automated continuous sampling plan (ACSP) shows the possibility of providing lower limit values for the average output defects level using the ACSP-1. Also, the average sample size when using the ACSP-1 plan is less than when using the CSP-1 plan. Thus, the application of statistical methods in the assembly quality management of multi-element products on automatic rotor lines, involving the use of proposed plans and methods for continuous selective control, will allow to automating sampling control procedures and the required level of quality of assembled products while minimizing sample size.

In Support of a Distinction between Voluntary and Stimulus-Driven Control: A Review of the Literature on Proportion Congruent Effects

PubMed Central

Bugg, Julie M.; Crump, Matthew J. C.

2012-01-01

Cognitive control is by now a large umbrella term referring collectively to multiple processes that plan and coordinate actions to meet task goals. A common feature of paradigms that engage cognitive control is the task requirement to select relevant information despite a habitual tendency (or bias) to select goal-irrelevant information. At least since the 1970s, researchers have employed proportion congruent (PC) manipulations to experimentally establish selection biases and evaluate the mechanisms used to control attention. PC manipulations vary the frequency with which irrelevant information conflicts (i.e., is incongruent) with relevant information. The purpose of this review is to summarize the growing body of literature on PC effects across selective attention paradigms, beginning first with Stroop, and then describing parallel effects in flanker and task-switching paradigms. The review chronologically tracks the expansion of the PC manipulation from its initial implementation at the list-wide level, to more recent implementations at the item-specific and context-specific levels. An important theoretical aim is demonstrating that PC effects at different levels (e.g., list-wide vs. item or context-specific) support a distinction between voluntary forms of cognitive control, which operate based on anticipatory information, and relatively automatic or reflexive forms of cognitive control, which are rapidly triggered by the processing of particular stimuli or stimulus features. A further aim is to highlight those PC manipulations that allow researchers to dissociate stimulus-driven control from other stimulus-driven processes (e.g., S-R responding; episodic retrieval). We conclude by discussing the utility of PC manipulations for exploring the distinction between voluntary control and stimulus-driven control in other relevant paradigms. PMID:23060836

Self-Control, Daily Negative Affect and Blood Glucose Control in Adolescents with Type 1 Diabetes

PubMed Central

Lansing, Amy Hughes; Berg, Cynthia A.; Butner, Jonathan; Wiebe, Deborah J.

2016-01-01

Objective For adolescents with type 1 diabetes, maintaining optimal daily blood glucose control is a complex self-regulatory process that likely requires self-control. This study examined whether higher self-control was associated with lower daily negative affect about diabetes and, in turn, better daily blood glucose control, i.e., lower mean daily blood glucose (MBG) and smaller standard deviations of daily blood glucose (SDBG), through two paths: 1) self-control maintaining lower mean level of negative affect and 2) self-control buffering the association of the number of daily diabetes problems with daily negative affect. Methods Adolescents (M age=12.87 years) with type 1 diabetes (n=180) completed an initial survey containing a self-report measure of self-control. Nightly electronic diaries were completed for 14 days where adolescents reported daily problems with and negative affect about diabetes, and used a study-provided blood glucose meter. Results Hypotheses were examined through multilevel modeling. Lower mean levels of daily negative affect partially mediated the relation between higher adolescent self-control and lower MBG. Adolescent self-control also buffered the association of the number of daily problems with daily negative affect, and smaller fluctuations in daily negative affect were associated with lower SDBG. Conclusions Adolescent self-control is associated with daily affect regulatory processes that may influence MBG. However, fluctuations in daily negative affect about diabetes may represent a unique within-person daily process associated with SDBG. These findings suggest that studies examining daily disease processes and interventions targeting daily affect regulation may be important to improving health in adolescents with type 1 diabetes. PMID:26914647

Electrophysiological evidence of enhanced performance monitoring in recently abstinent alcoholic men

PubMed Central

Padilla, Mayra L.; Sullivan, Edith V.; Mayer, Benjamin Z.; Turlington, Sharon R.; Hoffman, Lindsay R.; Wagstaff, Amanda E.; Pfefferbaum, Adolf

2010-01-01

Rationale Chronic alcoholism is associated with mild to moderate cognitive impairment. Under certain conditions, impairment can be ameliorated by invoking compensatory processes. Objective To identify electrophysiological mechanisms of such compensation that would be required to resolve response conflict. Methods 14 abstinent alcoholic men and 14 similarly aged control men performed a variation of the Eriksen flanker task during an electroencephalography (EEG) recording to examine whether alcoholics could achieve and maintain control-level performance and whether EEG markers could identify evidence for the action of compensatory processes in the alcoholics. Monitoring processes engaged following a response were indexed by the correct related negativity (CRN) and error related negativity (ERN), two medial–frontal negative event-related potentials. Results The alcoholics were able to perform at control levels on accuracy and reaction time (RT). Alcoholics generated larger ERN amplitudes following incorrect responses and larger CRNs following correct responses than controls. Both groups showed evidence of post-error slowing. Larger CRN amplitudes in the alcoholics were related to longer RTs. Also observed in the alcoholics was an association between smaller CRN amplitudes and length of sobriety, suggesting a normalization of monitoring activity with extended abstinence. Conclusions To the extent that greater amplitude of these electrophysiological markers of performance monitoring indexes greater resource allocation and performance compensation, the larger amplitudes observed in the alcoholic than control group support the view that elevated performance monitoring enables abstinent alcoholics to overcome response conflict, as was evident in their control-level performance. PMID:20941595

Control of campylobacter in poultry industry from farm to poultry processing unit: A review.

PubMed

Umaraw, Pramila; Prajapati, A; Verma, Akhilesh K; Pathak, V; Singh, V P

2017-03-04

Campylobacter is an emerging zoonotic bacterial threat in the poultry industry. Most of the human cases of campylobacteriosis recorded have revealed their poultry origins. Various control measures have been employed both at the farm and processing levels to combat with it. The antibiotic treatment, phage therapy, competitive exclusion, and vaccination have been adapted at the farm level to reduce colonization of Campylobacter in poultry gut. While prevention of intestinal spillage, scheduled slaughter, logistic slaughter, chemical decontamination of carcasses are recommended to reduce contamination during processing. The postharvest interventions such as heat treatment, freezing, irradiation of contaminated carcass can effectively reduce Campylobacter contamination. Thus, integrated approaches are required to tackle infection of Campylobacter in humans.

Control mechanisms for stochastic biochemical systems via computation of reachable sets.

PubMed

Lakatos, Eszter; Stumpf, Michael P H

2017-08-01

Controlling the behaviour of cells by rationally guiding molecular processes is an overarching aim of much of synthetic biology. Molecular processes, however, are notoriously noisy and frequently nonlinear. We present an approach to studying the impact of control measures on motifs of molecular interactions that addresses the problems faced in many biological systems: stochasticity, parameter uncertainty and nonlinearity. We show that our reachability analysis formalism can describe the potential behaviour of biological (naturally evolved as well as engineered) systems, and provides a set of bounds on their dynamics at the level of population statistics: for example, we can obtain the possible ranges of means and variances of mRNA and protein expression levels, even in the presence of uncertainty about model parameters.

Control mechanisms for stochastic biochemical systems via computation of reachable sets

PubMed Central

Lakatos, Eszter

2017-01-01

Controlling the behaviour of cells by rationally guiding molecular processes is an overarching aim of much of synthetic biology. Molecular processes, however, are notoriously noisy and frequently nonlinear. We present an approach to studying the impact of control measures on motifs of molecular interactions that addresses the problems faced in many biological systems: stochasticity, parameter uncertainty and nonlinearity. We show that our reachability analysis formalism can describe the potential behaviour of biological (naturally evolved as well as engineered) systems, and provides a set of bounds on their dynamics at the level of population statistics: for example, we can obtain the possible ranges of means and variances of mRNA and protein expression levels, even in the presence of uncertainty about model parameters. PMID:28878957

Cybernetic Basis and System Practice of Remote Sensing and Spatial Information Science

NASA Astrophysics Data System (ADS)

Tan, X.; Jing, X.; Chen, R.; Ming, Z.; He, L.; Sun, Y.; Sun, X.; Yan, L.

2017-09-01

Cybernetics provides a new set of ideas and methods for the study of modern science, and it has been fully applied in many areas. However, few people have introduced cybernetics into the field of remote sensing. The paper is based on the imaging process of remote sensing system, introducing cybernetics into the field of remote sensing, establishing a space-time closed-loop control theory for the actual operation of remote sensing. The paper made the process of spatial information coherently, and improved the comprehensive efficiency of the space information from acquisition, procession, transformation to application. We not only describes the application of cybernetics in remote sensing platform control, sensor control, data processing control, but also in whole system of remote sensing imaging process control. We achieve the information of output back to the input to control the efficient operation of the entire system. This breakthrough combination of cybernetics science and remote sensing science will improve remote sensing science to a higher level.

Simulation model for plant growth in controlled environment systems

NASA Technical Reports Server (NTRS)

Raper, C. D., Jr.; Wann, M.

1986-01-01

The role of the mathematical model is to relate the individual processes to environmental conditions and the behavior of the whole plant. Using the controlled-environment facilities of the phytotron at North Carolina State University for experimentation at the whole-plant level and methods for handling complex models, researchers developed a plant growth model to describe the relationships between hierarchial levels of the crop production system. The fundamental processes that are considered are: (1) interception of photosynthetically active radiation by leaves, (2) absorption of photosynthetically active radiation, (3) photosynthetic transformation of absorbed radiation into chemical energy of carbon bonding in solube carbohydrates in the leaves, (4) translocation between carbohydrate pools in leaves, stems, and roots, (5) flow of energy from carbohydrate pools for respiration, (6) flow from carbohydrate pools for growth, and (7) aging of tissues. These processes are described at the level of organ structure and of elementary function processes. The driving variables of incident photosynthetically active radiation and ambient temperature as inputs pertain to characterization at the whole-plant level. The output of the model is accumulated dry matter partitioned among leaves, stems, and roots; thus, the elementary processes clearly operate under the constraints of the plant structure which is itself the output of the model.

Quality Audit in the Fastener Industry

NASA Technical Reports Server (NTRS)

Reagan, John R.

1995-01-01

Both the financial and quality communities rely on audits to verify customers records. The financial community is highly structured around three categories of risk, INHERENT RISK, CONTROL RISK, and DETECTION RISK. Combined, the product of these three categories constitute the AUDIT RISK. The financial community establishes CONTROL RISK based in large part on a systems level understanding of the process flow. This system level understanding is best expressed in a flowchart. The quality community may be able to adopt this structure and thereby reduce cost while maintaining and enhancing quality. The quality community should attempt to flowchart the systems level quality process before beginning substantive testing. This theory needs to be applied in several trial cases to prove or disprove this hypothesis

Quality audit in the fastener industry

NASA Astrophysics Data System (ADS)

Reagan, John R.

1995-09-01

Both the financial and quality communities rely on audits to verify customers records. The financial community is highly structured around three categories of risk, INHERENT RISK, CONTROL RISK, and DETECTION RISK. Combined, the product of these three categories constitute the AUDIT RISK. The financial community establishes CONTROL RISK based in large part on a systems level understanding of the process flow. This system level understanding is best expressed in a flowchart. The quality community may be able to adopt this structure and thereby reduce cost while maintaining and enhancing quality. The quality community should attempt to flowchart the systems level quality process before beginning substantive testing. This theory needs to be applied in several trial cases to prove or disprove this hypothesis

Atypical biological motion kinematics are represented by complementary lower-level and top-down processes during imitation learning.

PubMed

Hayes, Spencer J; Dutoy, Chris A; Elliott, Digby; Gowen, Emma; Bennett, Simon J

2016-01-01

Learning a novel movement requires a new set of kinematics to be represented by the sensorimotor system. This is often accomplished through imitation learning where lower-level sensorimotor processes are suggested to represent the biological motion kinematics associated with an observed movement. Top-down factors have the potential to influence this process based on the social context, attention and salience, and the goal of the movement. In order to further examine the potential interaction between lower-level and top-down processes in imitation learning, the aim of this study was to systematically control the mediating effects during an imitation of biological motion protocol. In this protocol, we used non-human agent models that displayed different novel atypical biological motion kinematics, as well as a control model that displayed constant velocity. Importantly the three models had the same movement amplitude and movement time. Also, the motion kinematics were displayed in the presence, or absence, of end-state-targets. Kinematic analyses showed atypical biological motion kinematics were imitated, and that this performance was different from the constant velocity control condition. Although the imitation of atypical biological motion kinematics was not modulated by the end-state-targets, movement time was more accurate in the absence, compared to the presence, of an end-state-target. The fact that end-state targets modulated movement time accuracy, but not biological motion kinematics, indicates imitation learning involves top-down attentional, and lower-level sensorimotor systems, which operate as complementary processes mediated by the environmental context. Copyright © 2015 Elsevier B.V. All rights reserved.

Individuals with Asperger's disorder exhibit difficulty in switching attention from a local level to a global level.

PubMed

Katagiri, Masatoshi; Kasai, Tetsuko; Kamio, Yoko; Murohashi, Harumitsu

2013-02-01

The purpose of the present study was to determine whether individuals with Asperger's disorder exhibit difficulty in switching attention from a local level to a global level. Eleven participants with Asperger's disorder and 11 age- and gender-matched healthy controls performed a level-repetition switching task using Navon-type hierarchical stimuli. In both groups, level-repetition was beneficial at both levels. Furthermore, individuals with Asperger's disorder exhibited difficulty in switching attention from a local level to a global level compared to control individuals. These findings suggested that there is a problem with the inhibitory mechanism that influences the output of enhanced local visual processing in Asperger's disorder.

Control of plasma process by use of harmonic frequency components of voltage and current

DOEpatents

Miller, Paul A.; Kamon, Mattan

1994-01-01

The present invention provides for a technique for taking advantage of the intrinsic electrical non-linearity of processing plasmas to add additional control variables that affect process performance. The technique provides for the adjustment of the electrical coupling circuitry, as well as the electrical excitation level, in response to measurements of the reactor voltage and current and to use that capability to modify the plasma characteristics to obtain the desired performance.

Trace element control in binary Ni-25Cr and ternary Ni-30Co-30Cr master alloy castings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Detrois, Martin; Jablonski, Paul D.

Electro-slag remelting (ESR) is used for control of unwanted elements in commercial alloys. This study focuses on master alloys of Ni-25Cr and Ni-30Co-30Cr, processed through a combination of vacuum induction melting (VIM) and electro-slag remelting (ESR). Minor additions were made to control tramp element levels and modify the melting characteristics. Nitrogen and sulfur levels below 10 ppm and oxygen levels below 100 ppm were obtained in the final products. The role of the alloy additions in lowering the tramp element content, the resulting residual inclusions and the melting characteristics were determined computationally and confirmed experimentally. Additions of titanium were beneficialmore » to the control of oxygen levels during VIM and nitrogen levels during ESR. Aluminum additions helped to control oxygen levels during remelting, however, aluminum pickup occurred when excess titanium was present during ESR. The usefulness of these master alloys for use as experimental remelt stock will also be discussed.« less

[Discussion on research thinking of traditional Chinese medicine standardization system based on whole process quality control].

PubMed

Dong, Ling; Sun, Yu; Pei, Wen-Xuan; Dai, Jun-Dong; Wang, Zi-Yu; Pan, Meng; Chen, Jiang-Peng; Wang, Yun

2017-12-01

The concept of "Quality by design" indicates that good design for the whole life cycle of pharmaceutical production enables the drug to meet the expected quality requirements. Aiming at the existing problems of the traditional Chinese medicine (TCM) industry, the TCM standardization system was put forward in this paper from the national strategic level, under the guidance by the idea of quality control in international manufacturing industry and with considerations of TCM industry's own characteristics and development status. The connotation of this strategy was to establish five interrelated systems: multi-indicators system based on tri-indicators system, quality standard and specification system of TCM herbal materials and decoction pieces, quality traceability system, data monitoring system based on whole-process quality control, and whole-process quality management system of TCM, and achieve the whole process systematic and scientific study in TCM industry through "top-level design-implement in steps-system integration" workflow. This article analyzed the correlation between the quality standards of all links, established standard operating procedures of each link and whole process, and constructed a high standard overall quality management system for TCM industry chains, in order to provide a demonstration for the establishment of TCM whole-process quality control system and provide systematic reference and basis for standardization strategy in TCM industry. Copyright© by the Chinese Pharmaceutical Association.

Difference among Levels of Inquiry: Process Skills Improvement at Senior High School in Indonesia

ERIC Educational Resources Information Center

Hardianti, Tuti; Kuswanto, Heru

2017-01-01

The objective of the research concerned here was to discover the difference in effectiveness among Levels 2, 3, and 4 of inquiry learning in improving students' process skills. The research was a quasi-experimental study using the pretest-posttest non-equivalent control group research design. Three sample groups were selected by means of cluster…

Decreased Load on General Motor Preparation and Visual-Working Memory while Preparing Familiar as Compared to Unfamiliar Movement Sequences

ERIC Educational Resources Information Center

De Kleine, Elian; Van der Lubbe, Rob H. J.

2011-01-01

Learning movement sequences is thought to develop from an initial controlled attentive phase to a more automatic inattentive phase. Furthermore, execution of sequences becomes faster with practice, which may result from changes at a general motor processing level rather than at an effector specific motor processing level. In the current study, we…

What role does the anterior temporal lobe play in sentence-level processing? Neural correlates of syntactic processing in semantic PPA

PubMed Central

Wilson, Stephen M.; DeMarco, Andrew T.; Henry, Maya L.; Gesierich, Benno; Babiak, Miranda; Mandelli, Maria Luisa; Miller, Bruce L.; Gorno-Tempini, Maria Luisa

2014-01-01

Neuroimaging and neuropsychological studies have implicated the anterior temporal lobe (ATL) in sentence-level processing, with syntactic structure-building and/or combinatorial semantic processing suggested as possible roles. A potential challenge to the view that the ATL is involved in syntactic aspects of sentence processing comes from the clinical syndrome of semantic variant primary progressive aphasia (semantic PPA, also known as semantic dementia). In semantic PPA, bilateral neurodegeneration of the anterior temporal lobes is associated with profound lexical semantic deficits, yet syntax is strikingly spared. The goal of this study was to investigate the neural correlates of syntactic processing in semantic PPA, in order to determine which regions normally involved in syntactic processing are damaged in semantic PPA, and whether spared syntactic processing depends on preserved functionality of intact regions, preserved functionality of atrophic regions, or compensatory functional reorganization. We scanned 20 individuals with semantic PPA and 24 age-matched controls using structural and functional MRI. Participants performed a sentence comprehension task that emphasized syntactic processing and minimized lexical semantic demands. We found that in controls, left inferior frontal and left posterior temporal regions were modulated by syntactic processing, while anterior temporal regions were not significantly modulated. In the semantic PPA group, atrophy was most severe in the anterior temporal lobes, but extended to the posterior temporal regions involved in syntactic processing. Functional activity for syntactic processing was broadly similar in patients and controls; in particular, whole-brain analyses revealed no significant differences between patients and controls in the regions modulated by syntactic processing. The atrophic left anterior temporal lobe did show abnormal functionality in semantic PPA patients, however this took the unexpected form of a failure to deactivate. Taken together, our findings indicate that spared syntactic processing in semantic PPA depends on preserved functionality of structurally intact left frontal regions and moderately atrophic left posterior temporal regions, but no functional reorganization was apparent as a consequence of anterior temporal atrophy and dysfunction. These results suggest that the role of the anterior temporal lobe in sentence processing is less likely to relate to syntactic structure-building, and more likely to relate to higher level processes such as combinatorial semantic processing. PMID:24345172

P50 suppression in children with selective mutism: a preliminary report.

PubMed

Henkin, Yael; Feinholz, Maya; Arie, Miri; Bar-Haim, Yair

2010-01-01

Evidence suggests that children with selective mutism (SM) display significant aberrations in auditory efferent activity at the brainstem level that may underlie inefficient auditory processing during vocalization, and lead to speech avoidance. The objective of the present study was to explore auditory filtering processes at the cortical level in children with SM. The classic paired-click paradigm was utilized to assess suppression of the P50 event-related potential to the second, of two sequentially-presented clicks, in ten children with SM and 10 control children. A significant suppression of P50 to the second click was evident in the SM group, whereas no suppression effect was observed in controls. Suppression was evident in 90% of the SM group and in 40% of controls, whereas augmentation was found in 10% and 60%, respectively, yielding a significant association between group and suppression of P50. P50 to the first click was comparable in children with SM and controls. The adult-like, mature P50 suppression effect exhibited by children with SM may reflect a cortical mechanism of compensatory inhibition of irrelevant repetitive information that was not properly suppressed at lower levels of their auditory system. The current data extends our previous findings suggesting that differential auditory processing may be involved in speech selectivity in SM.

Robust algebraic image enhancement for intelligent control systems

NASA Technical Reports Server (NTRS)

Lerner, Bao-Ting; Morrelli, Michael

1993-01-01

Robust vision capability for intelligent control systems has been an elusive goal in image processing. The computationally intensive techniques a necessary for conventional image processing make real-time applications, such as object tracking and collision avoidance difficult. In order to endow an intelligent control system with the needed vision robustness, an adequate image enhancement subsystem capable of compensating for the wide variety of real-world degradations, must exist between the image capturing and the object recognition subsystems. This enhancement stage must be adaptive and must operate with consistency in the presence of both statistical and shape-based noise. To deal with this problem, we have developed an innovative algebraic approach which provides a sound mathematical framework for image representation and manipulation. Our image model provides a natural platform from which to pursue dynamic scene analysis, and its incorporation into a vision system would serve as the front-end to an intelligent control system. We have developed a unique polynomial representation of gray level imagery and applied this representation to develop polynomial operators on complex gray level scenes. This approach is highly advantageous since polynomials can be manipulated very easily, and are readily understood, thus providing a very convenient environment for image processing. Our model presents a highly structured and compact algebraic representation of grey-level images which can be viewed as fuzzy sets.

Advanced process control framework initiative

NASA Astrophysics Data System (ADS)

Hill, Tom; Nettles, Steve

1997-01-01

The semiconductor industry, one the world's most fiercely competitive industries, is driven by increasingly complex process technologies and global competition to improve cycle time, quality, and process flexibility. Due to the complexity of these problems, current process control techniques are generally nonautomated, time-consuming, reactive, nonadaptive, and focused on individual fabrication tools and processes. As the semiconductor industry moves into higher density processes, radical new approaches are required. To address the need for advanced factory-level process control in this environment, Honeywell, Advanced Micro Devices (AMD), and SEMATECH formed the Advanced Process Control Framework Initiative (APCFI) joint research project. The project defines and demonstrates an Advanced Process Control (APC) approach based on SEMATECH's Computer Integrated Manufacturing (CIM) Framework. Its scope includes the coordination of Manufacturing Execution Systems, process control tools, and wafer fabrication equipment to provide necessary process control capabilities. Moreover, it takes advantage of the CIM Framework to integrate and coordinate applications from other suppliers that provide services necessary for the overall system to function. This presentation discusses the key concept of model-based process control that differentiates the APC Framework. This major improvement over current methods enables new systematic process control by linking the knowledge of key process settings to desired product characteristics that reside in models created with commercial model development tools The unique framework-based approach facilitates integration of commercial tools and reuse of their data by tying them together in an object-based structure. The presentation also explores the perspective of each organization's involvement in the APCFI project. Each has complementary goals and expertise to contribute; Honeywell represents the supplier viewpoint, AMD represents the user with 'real customer requirements', and SEMATECH provides a consensus-building organization that widely disseminates technology to suppliers and users in the semiconductor industry that face similar equipment and factory control systems challenges.

64nm pitch metal1 double patterning metrology: CD and OVL control by SEMCD, image based overlay and diffraction based overlay

NASA Astrophysics Data System (ADS)

Ducoté, Julien; Dettoni, Florent; Bouyssou, Régis; Le-Gratiet, Bertrand; Carau, Damien; Dezauzier, Christophe

2015-03-01

Patterning process control of advanced nodes has required major changes over the last few years. Process control needs of critical patterning levels since 28nm technology node is extremely aggressive showing that metrology accuracy/sensitivity must be finely tuned. The introduction of pitch splitting (Litho-Etch-Litho-Etch) at 14FDSOInm node requires the development of specific metrologies to adopt advanced process control (for CD, overlay and focus corrections). The pitch splitting process leads to final line CD uniformities that are a combination of the CD uniformities of the two exposures, while the space CD uniformities are depending on both CD and OVL variability. In this paper, investigations of CD and OVL process control of 64nm minimum pitch at Metal1 level of 14FDSOI technology, within the double patterning process flow (Litho, hard mask etch, line etch) are presented. Various measurements with SEMCD tools (Hitachi), and overlay tools (KT for Image Based Overlay - IBO, and ASML for Diffraction Based Overlay - DBO) are compared. Metrology targets are embedded within a block instanced several times within the field to perform intra-field process variations characterizations. Specific SEMCD targets were designed for independent measurement of both line CD (A and B) and space CD (A to B and B to A) for each exposure within a single measurement during the DP flow. Based on those measurements correlation between overlay determined with SEMCD and with standard overlay tools can be evaluated. Such correlation at different steps through the DP flow is investigated regarding the metrology type. Process correction models are evaluated with respect to the measurement type and the intra-field sampling.

Depth of word processing in Alzheimer patients and normal controls: a magnetoencephalographic (MEG) study.

PubMed

Walla, P; Püregger, E; Lehrner, J; Mayer, D; Deecke, L; Dal Bianco, P

2005-05-01

Effects related to depth of verbal information processing were investigated in probable Alzheimer's disease patients (AD) and age matched controls. During word encoding sessions 10 patients and 10 controls had either to decide whether the letter "s" appeared in visually presented words (alphabetical decision, shallow encoding), or whether the meaning of each presented word was animate or inanimate (lexical decision, deep encoding). These encoding sessions were followed by test sessions during which all previously encoded words were presented again together with the same number of new words. The task was then to discriminate between repeated and new words. Magnetic field changes related to brain activity were recorded with a whole cortex MEG.5 probable AD patients showed recognition performances above chance level related to both depths of information processing. Those patients and 5 age matched controls were then further analysed. Recognition performance was poorer in probable AD patients compared to controls for both levels of processing. However, in both groups deep encoding led to a higher recognition performance than shallow encoding. We therefore conclude that the performance reduction in the patient group was independent of depth of processing. Reaction times related to false alarms differed between patients and controls after deep encoding which perhaps could already be used for supporting an early diagnosis. The analysis of the physiological data revealed significant differences between correctly recognised repetitions and correctly classified new words (old/new-effect) in the control group which were missing in the patient group after deep encoding. The lack of such an effect in the patient group is interpreted as being due to the respective neuropathology related to probable AD. The present results demonstrate that magnetic field recordings represent a useful tool to physiologically distinguish between probable AD and age matched controls.

Adaptation of a Control Center Development Environment for Industrial Process Control

NASA Technical Reports Server (NTRS)

Killough, Ronnie L.; Malik, James M.

1994-01-01

In the control center, raw telemetry data is received for storage, display, and analysis. This raw data must be combined and manipulated in various ways by mathematical computations to facilitate analysis, provide diversified fault detection mechanisms, and enhance display readability. A development tool called the Graphical Computation Builder (GCB) has been implemented which provides flight controllers with the capability to implement computations for use in the control center. The GCB provides a language that contains both general programming constructs and language elements specifically tailored for the control center environment. The GCB concept allows staff who are not skilled in computer programming to author and maintain computer programs. The GCB user is isolated from the details of external subsystem interfaces and has access to high-level functions such as matrix operators, trigonometric functions, and unit conversion macros. The GCB provides a high level of feedback during computation development that improves upon the often cryptic errors produced by computer language compilers. An equivalent need can be identified in the industrial data acquisition and process control domain: that of an integrated graphical development tool tailored to the application to hide the operating system, computer language, and data acquisition interface details. The GCB features a modular design which makes it suitable for technology transfer without significant rework. Control center-specific language elements can be replaced by elements specific to industrial process control.

Flood replenishment: a new method of processor control.

PubMed

Frank, E D; Gray, J E; Wilken, D A

1980-01-01

In mechanized radiographic film processors that process medium to low volumes of film, roll films, and those that process single-emulsion films from nuclear medicine scans, computed tomography, and ultrasound, it is difficult to maintain the developer solution at a stable processing level. We describe our experience using flood replenishment, which is a method in which developer replenisher containing starter solution is introduced in the processor at timed intervals, independent of the number of films being processed. By this process, a stable level of developer activity is maintained in a processor used to develop a medium to low volume of single-emulsion film.

No evidence for common processes of cognitive control and self-control.

PubMed

Scherbaum, Stefan; Frisch, Simon; Holfert, Anna-Maria; O'Hora, Denis; Dshemuchadse, Maja

2018-01-01

Cognitive control and self-control are often used as interchangeable terms. Both terms refer to the ability to pursue long-term goals, but the types of controlled behavior that are typically associated with these terms differ, at least superficially. Cognitive control is observed in the control of attention and the overcoming of habitual responses, while self-control is observed in resistance to short-term impulses and temptations. Evidence from clinical studies and neuroimaging studies suggests that below these superficial differences, common control process (e.g., inhibition) might guide both types of controlled behavior. Here, we study this hypothesis in a behavioral experiment, which interlaced trials of a Simon task with trials of an intertemporal decision task. If cognitive control and self-control depend on a common control process, we expected conflict adaptation from Simon task trials to lead to increased self-control in the intertemporal decision trials. However, despite successful manipulations of conflict and conflict adaptation, we found no evidence for this hypothesis. We investigate a number of alternative explanations of this result and conclude that the differences between cognitive control and self-control are not superficial, but rather reflect differences at the process level. Copyright © 2017 Elsevier B.V. All rights reserved.

Model and Analytic Processes for Export License Assessments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, Sandra E.; Whitney, Paul D.; Weimar, Mark R.

2011-09-29

This paper represents the Department of Energy Office of Nonproliferation Research and Development (NA-22) Simulations, Algorithms and Modeling (SAM) Program's first effort to identify and frame analytical methods and tools to aid export control professionals in effectively predicting proliferation intent; a complex, multi-step and multi-agency process. The report focuses on analytical modeling methodologies that alone, or combined, may improve the proliferation export control license approval process. It is a follow-up to an earlier paper describing information sources and environments related to international nuclear technology transfer. This report describes the decision criteria used to evaluate modeling techniques and tools to determinemore » which approaches will be investigated during the final 2 years of the project. The report also details the motivation for why new modeling techniques and tools are needed. The analytical modeling methodologies will enable analysts to evaluate the information environment for relevance to detecting proliferation intent, with specific focus on assessing risks associated with transferring dual-use technologies. Dual-use technologies can be used in both weapons and commercial enterprises. A decision-framework was developed to evaluate which of the different analytical modeling methodologies would be most appropriate conditional on the uniqueness of the approach, data availability, laboratory capabilities, relevance to NA-22 and Office of Arms Control and Nonproliferation (NA-24) research needs and the impact if successful. Modeling methodologies were divided into whether they could help micro-level assessments (e.g., help improve individual license assessments) or macro-level assessment. Macro-level assessment focuses on suppliers, technology, consumers, economies, and proliferation context. Macro-level assessment technologies scored higher in the area of uniqueness because less work has been done at the macro level. An approach to developing testable hypotheses for the macro-level assessment methodologies is provided. The outcome of this works suggests that we should develop a Bayes Net for micro-level analysis and continue to focus on Bayes Net, System Dynamics and Economic Input/Output models for assessing macro-level problems. Simultaneously, we need to develop metrics for assessing intent in export control, including the risks and consequences associated with all aspects of export control.« less

Comparison of AOPs for the removal of natural organic matter: performance and economic assessment.

PubMed

Murray, C A; Parsons, S A

2004-01-01

Control of disinfection by-products during water treatment is primarily achieved by reducing the levels of organic precursor species prior to chlorination. Many waters contain natural organic matter at levels up to 15 mg L(-1); therefore it is necessary to have a range of control methods to support conventional coagulation. Advanced oxidation processes are such processes and in this paper the Fenton and photo-Fenton processes along with photocatalysis are assessed for their NOM removal potential. The performance of each process is shown to be dependent on pH and chemical dose as well as the initial NOM concentration. Under optimum conditions the processes achieved greater than 90% removal of DOC and UV254 absorbance. This removal led to the THMFP of the source water being reduced from 140 to below 10 microg L(-1), well below UK and US standards. An economic assessment of the processes revealed that currently such processes are not economic. With advances in technology and tightening of water quality standards these processes should become economically feasible options.

Flight-Test Validation and Flying Qualities Evaluation of a Rotorcraft UAV Flight Control System

NASA Technical Reports Server (NTRS)

Mettler, Bernard; Tuschler, Mark B.; Kanade, Takeo

2000-01-01

This paper presents a process of design and flight-test validation and flying qualities evaluation of a flight control system for a rotorcraft-based unmanned aerial vehicle (RUAV). The keystone of this process is an accurate flight-dynamic model of the aircraft, derived by using system identification modeling. The model captures the most relevant dynamic features of our unmanned rotorcraft, and explicitly accounts for the presence of a stabilizer bar. Using the identified model we were able to determine the performance margins of our original control system and identify limiting factors. The performance limitations were addressed and the attitude control system was 0ptimize.d for different three performance levels: slow, medium, fast. The optimized control laws will be implemented in our RUAV. We will first determine the validity of our control design approach by flight test validating our optimized controllers. Subsequently, we will fly a series of maneuvers with the three optimized controllers to determine the level of flying qualities that can be attained. The outcome enable us to draw important conclusions on the flying qualities requirements for small-scale RUAVs.

Stimulus-level interference disrupts repetition benefit during task switching in middle childhood

PubMed Central

Karayanidis, Frini; Jamadar, Sharna; Sanday, Dearne

2013-01-01

The task-switching paradigm provides a powerful tool to measure the development of core cognitive control processes. In this study, we use the alternating runs task-switching paradigm to assess preparatory control processes involved in flexibly preparing for a predictable change in task and stimulus-driven control processes involved in controlling stimulus-level interference. We present three experiments that examine behavioral and event-related potential (ERP) measures of task-switching performance in middle childhood and young adulthood under low and high stimulus interference conditions. Experiment 1 confirms that our new child-friendly tasks produce similar behavioral and electrophysiological findings in young adults as those previously reported. Experiment 2 examines task switching with univalent stimuli across a range of preparation intervals in middle childhood. Experiment 3 compares task switching with bivalent stimuli across the same preparation intervals in children and young adults. Children produced a larger RT switch cost than adults with univalent stimuli and a short preparation interval. Both children and adults showed significant reduction in switch cost with increasing preparation interval, but in children this was caused by greater increase in RT for repeat than switch trials. Response-locked ERPs showed intact preparation for univalent, but less efficient preparation for bivalent stimulus conditions. Stimulus-locked ERPs confirmed that children showed greater stimulus-level interference for repeat trials, especially with bivalent stimuli. We conclude that children show greater stimulus-level interference especially for repeat trials under high interference conditions, suggesting weaker mental representation of the current task set. PMID:24367317

Age-related decline in cognitive control: the role of fluid intelligence and processing speed

PubMed Central

2014-01-01

Background Research on cognitive control suggests an age-related decline in proactive control abilities whereas reactive control seems to remain intact. However, the reason of the differential age effect on cognitive control efficiency is still unclear. This study investigated the potential influence of fluid intelligence and processing speed on the selective age-related decline in proactive control. Eighty young and 80 healthy older adults were included in this study. The participants were submitted to a working memory recognition paradigm, assessing proactive and reactive cognitive control by manipulating the interference level across items. Results Repeated measures ANOVAs and hierarchical linear regressions indicated that the ability to appropriately use cognitive control processes during aging seems to be at least partially affected by the amount of available cognitive resources (assessed by fluid intelligence and processing speed abilities). Conclusions This study highlights the potential role of cognitive resources on the selective age-related decline in proactive control, suggesting the importance of a more exhaustive approach considering the confounding variables during cognitive control assessment. PMID:24401034

Using OPC technology to support the study of advanced process control.

PubMed

Mahmoud, Magdi S; Sabih, Muhammad; Elshafei, Moustafa

2015-03-01

OPC, originally the Object Linking and Embedding (OLE) for Process Control, brings a broad communication opportunity between different kinds of control systems. This paper investigates the use of OPC technology for the study of distributed control systems (DCS) as a cost effective and flexible research tool for the development and testing of advanced process control (APC) techniques in university research centers. Co-Simulation environment based on Matlab, LabVIEW and TCP/IP network is presented here. Several implementation issues and OPC based client/server control application have been addressed for TCP/IP network. A nonlinear boiler model is simulated as OPC server and OPC client is used for closed loop model identification, and to design a Model Predictive Controller. The MPC is able to control the NOx emissions in addition to drum water level and steam pressure. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Oxygen-controlled automated neural differentiation of mouse embryonic stem cells.

PubMed

Mondragon-Teran, Paul; Tostoes, Rui; Mason, Chris; Lye, Gary J; Veraitch, Farlan S

2013-03-01

Automation and oxygen tension control are two tools that provide significant improvements to the reproducibility and efficiency of stem cell production processes. the aim of this study was to establish a novel automation platform capable of controlling oxygen tension during both the cell-culture and liquid-handling steps of neural differentiation processes. We built a bespoke automation platform, which enclosed a liquid-handling platform in a sterile, oxygen-controlled environment. An airtight connection was used to transfer cell culture plates to and from an automated oxygen-controlled incubator. Our results demonstrate that our system yielded comparable cell numbers, viabilities, metabolism profiles and differentiation efficiencies when compared with traditional manual processes. Interestingly, eliminating exposure to ambient conditions during the liquid-handling stage resulted in significant improvements in the yield of MAP2-positive neural cells, indicating that this level of control can improve differentiation processes. This article describes, for the first time, an automation platform capable of maintaining oxygen tension control during both the cell-culture and liquid-handling stages of a 2D embryonic stem cell differentiation process.

Self-Esteem, Splitting, Anxiety, Fear, Depression, Anxiety Sensitivity and Locus of Control as They Relate to the Homosexual Identity Formation Process.

ERIC Educational Resources Information Center

Binks, Sidney Walter, III

This study proposed that before comparisons between homosexuals and heterosexuals on levels of self-esteem, anxiety, depression, and locus of control can be made, one must understand the unique process of homosexual identity formation and how it differs from heterosexual identity formation. Subjects included 231 male and 21 female members (ages…

Planning Following Stroke: A Relational Complexity Approach Using the Tower of London

PubMed Central

Andrews, Glenda; Halford, Graeme S.; Chappell, Mark; Maujean, Annick; Shum, David H. K.

2014-01-01

Planning on the 4-disk version of the Tower of London (TOL4) was examined in stroke patients and unimpaired controls. Overall TOL4 solution scores indicated impaired planning in the frontal stroke but not non-frontal stroke patients. Consistent with the claim that processing the relations between current states, intermediate states, and goal states is a key process in planning, the domain-general relational complexity metric was a good indicator of the experienced difficulty of TOL4 problems. The relational complexity metric shared variance with task-specific metrics of moves to solution and search depth. Frontal stroke patients showed impaired planning compared to controls on problems at all three complexity levels, but at only two of the three levels of moves to solution, search depth and goal ambiguity. Non-frontal stroke patients showed impaired planning only on the most difficult quaternary-relational and high search depth problems. An independent measure of relational processing (viz., Latin square task) predicted TOL4 solution scores after controlling for stroke status and location, and executive processing (Trail Making Test). The findings suggest that planning involves a domain-general capacity for relational processing that depends on the frontal brain regions. PMID:25566042

Reinventing The Design Process: Teams and Models

NASA Technical Reports Server (NTRS)

Wall, Stephen D.

1999-01-01

The future of space mission designing will be dramatically different from the past. Formerly, performance-driven paradigms emphasized data return with cost and schedule being secondary issues. Now and in the future, costs are capped and schedules fixed-these two variables must be treated as independent in the design process. Accordingly, JPL has redesigned its design process. At the conceptual level, design times have been reduced by properly defining the required design depth, improving the linkages between tools, and managing team dynamics. In implementation-phase design, system requirements will be held in crosscutting models, linked to subsystem design tools through a central database that captures the design and supplies needed configuration management and control. Mission goals will then be captured in timelining software that drives the models, testing their capability to execute the goals. Metrics are used to measure and control both processes and to ensure that design parameters converge through the design process within schedule constraints. This methodology manages margins controlled by acceptable risk levels. Thus, teams can evolve risk tolerance (and cost) as they would any engineering parameter. This new approach allows more design freedom for a longer time, which tends to encourage revolutionary and unexpected improvements in design.

Face-Name Association Learning and Brain Structural Substrates in Alcoholism

PubMed Central

Pitel, Anne-Lise; Chanraud, Sandra; Rohlfing, Torsten; Pfefferbaum, Adolf; Sullivan, Edith V.

2011-01-01

Background Associative learning is required for face-name association and is impaired in alcoholism, but the cognitive processes and brain structural components underlying this deficit remain unclear. It is also unknown whether prompting alcoholics to implement a deep level of processing during face-name encoding would enhance performance. Methods Abstinent alcoholics and controls performed a levels-of-processing face-name learning task. Participants indicated whether the face was that of an honest person (deep encoding) or that of a man (shallow encoding). Retrieval was examined using an associative (face-name) recognition task and a single-item (face or name only) recognition task. Participants also underwent a 3T structural MRI. Results Compared with controls, alcoholics had poorer associative and single-item recognition, each impaired to the same extent. Level of processing at encoding had little effect on recognition performance but affected reaction time. Correlations with brain volumes were generally modest and based primarily on reaction time in alcoholics, where the deeper the processing at encoding, the more restricted the correlations with brain volumes. In alcoholics, longer control task reaction times correlated modestly with volumes across several anterior to posterior brain regions; shallow encoding correlated with calcarine and striatal volumes; deep encoding correlated with precuneus and parietal volumes; associative recognition RT correlated with cerebellar volumes. In controls, poorer associative recognition with deep encoding correlated significantly with smaller volumes of frontal and striatal structures. Conclusions Despite prompting, alcoholics did not take advantage of encoding memoranda at a deep level to enhance face-name recognition accuracy. Nonetheless, conditions of deeper encoding resulted in faster reaction times and more specific relations with regional brain volumes than did shallow encoding. The normal relation between associative recognition and corticostriatal volumes was not present in alcoholics. Rather, their speeded reaction time occurred at the expense of accuracy and was related most robustly to cerebellar volumes. PMID:22509954

The relationship between health related quality of life and sensory deficits among patients with diabetes mellitus.

PubMed

Engel-Yeger, Batya; Darawsha Najjar, Sanaa; Darawsha, Mahmud

2017-08-13

(1) To profile sensory deficits examined in the ability to process sensory information from daily environment and discriminate between tactile stimuli among patients with controlled and un-controlled diabetes mellitus. (2) Examine the relationship between the sensory deficits and patients' health-related quality of life. This study included 115 participants aged 33-55 with uncontrolled (n = 22) or controlled (n = 24) glycemic levels together with healthy subjects (n = 69). All participants completed the brief World Health Organization Quality of Life Questionnaire, the Adolescent/Adult Sensory Profile and performed the tactile discrimination test. Sensory deficits were more emphasized among patients with uncontrolled glycemic levels as expressed in difficulties to register sensory input, lower sensation seeking in daily environments and difficulties to discriminate between tactile stimuli. They also reported the lowest physical and social quality of life as compared to the other two groups. Better sensory seeking and registration predicted better quality of life. Disease control and duration contributed to these predictions. Difficulties in processing sensory information from their daily environments are particularly prevalent among patients with uncontrolled glycemic levels, and significantly impacted their quality of life. Clinicians should screen for sensory processing difficulties among patients with diabetes mellitus and understand their impacts on patients' quality of life. Implications for Rehabilitation Patients with diabetes mellitus, and particularly those with uncontrolled glycemic levels, may have difficulties in processing sensory information from daily environment. A multidisciplinary intervention approach is recommended: clinicians should screen for sensory processing deficits among patients with diabetes mellitus and understand their impacts on patients' daily life. By providing the patients with environmental adaptations and coping strategies, clinicians may assist in optimizing sensory experiences in real life context and elevate patients' quality of life. Relating to quality of life and emphasizing a multidisciplinary approach is of major importance in broadening our understanding of health conditions and providing holistic treatment for patients.

Emotion Processing in Parkinson’s Disease: A Three-Level Study on Recognition, Representation, and Regulation

PubMed Central

Enrici, Ivan; Adenzato, Mauro; Ardito, Rita B.; Mitkova, Antonia; Cavallo, Marco; Zibetti, Maurizio; Lopiano, Leonardo; Castelli, Lorys

2015-01-01

Background Parkinson’s disease (PD) is characterised by well-known motor symptoms, whereas the presence of cognitive non-motor symptoms, such as emotional disturbances, is still underestimated. One of the major problems in studying emotion deficits in PD is an atomising approach that does not take into account different levels of emotion elaboration. Our study addressed the question of whether people with PD exhibit difficulties in one or more specific dimensions of emotion processing, investigating three different levels of analyses, that is, recognition, representation, and regulation. Methodology Thirty-two consecutive medicated patients with PD and 25 healthy controls were enrolled in the study. Participants performed a three-level analysis assessment of emotional processing using quantitative standardised emotional tasks: the Ekman 60-Faces for emotion recognition, the full 36-item version of the Reading the Mind in the Eyes (RME) for emotion representation, and the 20-item Toronto Alexithymia Scale (TAS-20) for emotion regulation. Principal Findings Regarding emotion recognition, patients obtained significantly worse scores than controls in the total score of Ekman 60-Faces but not in any other basic emotions. For emotion representation, patients obtained significantly worse scores than controls in the RME experimental score but no in the RME gender control task. Finally, on emotion regulation, PD and controls did not perform differently at TAS-20 and no specific differences were found on TAS-20 subscales. The PD impairments on emotion recognition and representation do not correlate with dopamine therapy, disease severity, or with the duration of illness. These results are independent from other cognitive processes, such as global cognitive status and executive function, or from psychiatric status, such as depression, anxiety or apathy. Conclusions These results may contribute to better understanding of the emotional problems that are often seen in patients with PD and the measures used to test these problems, in particular on the use of different versions of the RME task. PMID:26110271

Self-assembly and hierarchical patterning of aligned organic nanowire arrays by solvent evaporation on substrates with patterned wettability.

PubMed

Bao, Rong-Rong; Zhang, Cheng-Yi; Zhang, Xiu-Juan; Ou, Xue-Mei; Lee, Chun-Sing; Jie, Jian-Sheng; Zhang, Xiao-Hong

2013-06-26

The controlled growth and alignment of one-dimensional organic nanostructures at well-defined locations considerably hinders the integration of nanostructures for electronic and optoelectronic applications. Here, we demonstrate a simple process to achieve the growth, alignment, and hierarchical patterning of organic nanowires on substrates with controlled patterns of surface wettability. The first-level pattern is confined by the substrate patterns of wettability. Organic nanostructures are preferentially grown on solvent wettable regions. The second-level pattern is the patterning of aligned organic nanowires deposited by controlling the shape and movement of the solution contact lines during evaporation on the wettable regions. This process is controlled by the cover-hat-controlled method or vertical evaportation method. Therefore, various new patterns of organic nanostructures can be obtained by combing these two levels of patterns. This simple method proves to be a general approach that can be applied to other organic nanostructure systems. Using the as-prepared patterned nanowire arrays, an optoelectronic device (photodetector) is easily fabricated. Hence, the proposed simple, large-scale, low-cost method of preparing patterns of highly ordered organic nanostructures has high potential applications in various electronic and optoelectronic devices.

A three-level support method for smooth switching of the micro-grid operation model

NASA Astrophysics Data System (ADS)

Zong, Yuanyang; Gong, Dongliang; Zhang, Jianzhou; Liu, Bin; Wang, Yun

2018-01-01

Smooth switching of micro-grid between the grid-connected operation mode and off-grid operation mode is one of the key technologies to ensure it runs flexible and efficiently. The basic control strategy and the switching principle of micro-grid are analyzed in this paper. The reasons for the fluctuations of the voltage and the frequency in the switching process are analyzed from views of power balance and control strategy, and the operation mode switching strategy has been improved targeted. From the three aspects of controller’s current inner loop reference signal, voltage outer loop control strategy optimization and micro-grid energy balance management, a three-level security strategy for smooth switching of micro-grid operation mode is proposed. From the three aspects of controller’s current inner loop reference signal tracking, voltage outer loop control strategy optimization and micro-grid energy balance management, a three-level strategy for smooth switching of micro-grid operation mode is proposed. At last, it is proved by simulation that the proposed control strategy can make the switching process smooth and stable, the fluctuation problem of the voltage and frequency has been effectively improved.

Deficits of unconscious emotional processing in patients with major depression: An ERP study.

PubMed

Zhang, Dandan; He, Zhenhong; Chen, Yuming; Wei, Zhaoguo

2016-07-15

Major depressive disorder (MDD) is associated with behavioral and neurobiological evidences of negative bias in unconscious emotional processing. However, little is known about the time course of this deficit. The current study aimed to explore the unconscious processing of emotional facial expressions in MDD patients by means of event-related potentials (ERPs). The ERP responses to subliminally presented happy/neutral/sad faces were recorded in 26 medication-free patients and 26 healthy controls in a backward masking task. Three ERP components were compared between patients and controls. Detection accuracy was at chance level for both groups, suggesting that the process was performed in the absence of conscious awareness of the emotional stimuli. Robust emotion×group interactions were observed in P1, N170 and P3. Compared with the neutral faces, 1) the patients showed larger P1 for sad and smaller P1 for happy faces; however, the controls showed a completely inverse P1 pattern; 2) the controls exhibited larger N170 in the happy but not in the sad trials, whereas patients had comparable larger N170 amplitudes in sad and happy trials; 3) although both groups exhibited larger P3 for emotional faces, the patients showed a priority for sad trials while the controls showed a priority for happy trials. Our data suggested that negative processing bias exists on the unconscious level in individuals with MDD. The ERP measures indicated that the unconscious emotional processing in MDD patients has a time course of three-stage deflection. Copyright © 2016 Elsevier B.V. All rights reserved.

Changes in cognitive control in pre-manifest Huntington's disease examined using pre-saccadic EEG potentials - a longitudinal study.

PubMed

Ness, Vanessa; Bestgen, Anne-Kathrin; Saft, Carsten; Beste, Christian

2014-01-01

It is well-known that Huntington's disease (HD) affects saccadic processing. However, saccadic dysfunctions in HD may be seen as a result of dysfunctional processes occurring at the oculomotor level prior to the execution of saccades, i.e., at a pre-saccadic level. Virtually nothing is known about possible changes in pre-saccadic processes in HD. This study examines pre-saccadic processing in pre-manifest HD gene mutation carriers (pre-HDs) by using clinically available EEG measures. Error rates, pre-saccadic EEG potentials and saccade onset EEG potentials were measured in 14 pre-HDs and case-matched controls performing prosaccades and antisaccades in a longitudinal study over a 15-month period. The results show that pre-saccadic potentials were changed in pre-HDs, relative to controls and also revealed changes across the 15-month longitudinal period. In particular, pre-saccadic ERP in pre-HDs were characterized by lower amplitudes and longer latencies, which revealed longitudinal changes. These changes were observed for anti-saccades, but not for pro-saccades. Overt saccadic trajectories (potentials) were not different to those in controls, showing that pre-saccadic processes are sensitive to subtle changes in fronto-striatal networks in pre-HDs. Deficits in pre-saccadic processes prior the execution of an erroneous anti-saccade can be seen as an effect of dysfunctional cognitive control in HD. This may underlie saccadic abnormalities and hence a major phenotype of HD. Pre-saccadic EEG potentials preceding erroneous anti-saccades are sensitive to pre-manifest disease progression in HD.

Concept for Highly Mechanized Data Processing, Project 111.

DTIC Science & Technology

A concept is developed for a highly mechanized maintenance data processing system capable of deriving factors, influences, and correlations to raise...the level of logistics knowledge and lead to the design of a management-control system. (Author)

Logistics Control Facility: A Normative Model for Total Asset Visibility in the Air Force Logistics System

DTIC Science & Technology

1994-09-01

IIssue Computers, information systems, and communication systems are being increasingly used in transportation, warehousing, order processing , materials...inventory levels, reduced order processing times, reduced order processing costs, and increased customer satisfaction. While purchasing and transportation...process, the speed in which crders are processed would increase significantly. Lowering the order processing time in turn lowers the lead time, which in

A novel multi-level IC-compatible surface microfabrication technology for MEMS with independently controlled lateral and vertical submicron transduction gaps

NASA Astrophysics Data System (ADS)

Cicek, Paul-Vahe; Elsayed, Mohannad; Nabki, Frederic; El-Gamal, Mourad

2017-11-01

An above-IC compatible multi-level MEMS surface microfabrication technology based on a silicon carbide structural layer is presented. The fabrication process flow provides optimal electrostatic transduction by allowing the creation of independently controlled submicron vertical and lateral gaps without the need for high resolution lithography. Adopting silicon carbide as the structural material, the technology ensures material, chemical and thermal compatibility with modern semiconductor nodes, reporting the lowest peak processing temperature (i.e. 200 °C) of all comparable works. This makes this process ideally suited for integrating capacitive-based MEMS directly above standard CMOS substrates. Process flow design and optimization are presented in the context of bulk-mode disk resonators, devices that are shown to exhibit improved performance with respect to previous generation flexural beam resonators, and that represent relatively complex MEMS structures. The impact of impending improvements to the fabrication technology is discussed.

Report: EPA Needs to Strengthen Internal Controls for Determining Workforce Levels

EPA Pesticide Factsheets

Report #11-P-0031, December 20, 2010. EPA’s policies and procedures do not include a process for determining employment levels based on workload as prescribed by the Office of Management and Budget.

Breaking continuous flash suppression: competing for consciousness on the pre-semantic battlefield

PubMed Central

Gayet, Surya; Van der Stigchel, Stefan; Paffen, Chris L. E.

2014-01-01

Traditionally, interocular suppression is believed to disrupt high-level (i.e., semantic or conceptual) processing of the suppressed visual input. The development of a new experimental paradigm, breaking continuous flash suppression (b-CFS), has caused a resurgence of studies demonstrating high-level processing of visual information in the absence of visual awareness. In this method the time it takes for interocularly suppressed stimuli to breach the threshold of visibility, is regarded as a measure of access to awareness. The aim of the current review is twofold. First, we provide an overview of the literature using this b-CFS method, while making a distinction between two types of studies: those in which suppression durations are compared between different stimulus classes (such as upright faces versus inverted faces), and those in which suppression durations are compared for stimuli that either match or mismatch concurrently available information (such as a colored target that either matches or mismatches a color retained in working memory). Second, we aim at dissociating high-level processing from low-level (i.e., crude visual) processing of the suppressed stimuli. For this purpose, we include a thorough review of the control conditions that are used in these experiments. Additionally, we provide recommendations for proper control conditions that we deem crucial for disentangling high-level from low-level effects. Based on this review, we argue that crude visual processing suffices for explaining differences in breakthrough times reported using b-CFS. As such, we conclude that there is as yet no reason to assume that interocularly suppressed stimuli receive full semantic analysis. PMID:24904476

Medial frontal GABA is lower in older schizophrenia: a MEGA-PRESS with macromolecule suppression study.

PubMed

Rowland, L M; Krause, B W; Wijtenburg, S A; McMahon, R P; Chiappelli, J; Nugent, K L; Nisonger, S J; Korenic, S A; Kochunov, P; Hong, L E

2016-02-01

Gamma-butyric acid (GABA) dysfunction has been implicated in the pathophysiology of schizophrenia and its cognitive deficits. Proton magnetic resonance spectroscopy (MRS) was used to test the hypothesis that older participants with schizophrenia have lower anterior cingulate GABA levels compared with older control participants. One-hundred forty-five participants completed this study. For detection of GABA, spectra were acquired from the medial frontal/anterior cingulate cortex using a macromolecule-suppressed MEGA-PRESS sequence. Patients were evaluated for psychopathology and all participants completed neuropsychological tests of working memory, processing speed and functional capacity. GABA levels were significantly lower in the older participants with schizophrenia (n=31) compared with the older control (n=37) group (P=0.003) but not between the younger control (n=40) and schizophrenia (n=29) groups (P=0.994). Age strongly predicted GABA levels in the schizophrenia group accounting for 42% of the variance, but the effect of age was less in the control group accounting for 5.7% of the variance. GABA levels were specifically related to working memory but not processing speed performance, functional capacity, or positive or negative symptom severity. This is the largest MRS study of GABA in schizophrenia and the first to examine GABA without macromolecule contamination, a potentially significant issue in previous studies. GABA levels more rapidly declined with advancing age in the schizophrenia compared with the control group. Interventions targeted at halting the decline or increasing GABA levels may improve functional outcomes and quality of life as patients with schizophrenia age.

Medial Frontal GABA is Lower in Older Schizophrenia: A MEGA-PRESS with Macromolecule Suppression Study

PubMed Central

Rowland, Laura M; Krause, Benjamin W.; Wijtenburg, S. Andrea; McMahon, Robert P.; Chiappelli, Joshua; Nugent, Katie L.; Nisonger, Sarah J.; Korenic, Stephanie A.; Kochunov, Peter; Hong, L. Elliot

2015-01-01

Gamma-butyric acid (GABA) dysfunction has been implicated in the pathophysiology of schizophrenia and its cognitive deficits. Proton magnetic resonance spectroscopy (MRS) was used to test the hypothesis that older participants with schizophrenia have lower anterior cingulate GABA levels compared to older control participants. One-hundred and forty-five participants completed this study. For detection of GABA, spectra were acquired from the medial frontal/anterior cingulate cortex using a macromolecule-suppressed MEGA-PRESS sequence. Patients were evaluated for psychopathology and all participants completed neuropsychological tests of working memory, processing speed, and functional capacity. GABA levels were significantly lower in the older participants with schizophrenia(n=31) compared to the older control(n=37) group (p=0.003) but not between the younger control(n=40) and schizophrenia (n=29) groups (p=0.994). Age strongly predicted GABA levels in the schizophrenia group accounting for 42% of the variance, but the effect of age was less in the control group accounting for 5.7% of the variance. GABA levels were specifically related to working memory but not processing speed performance, functional capacity, or positive or negative symptom severity. This is the largest MRS study of GABA in schizophrenia and the first to examine GABA without macromolecule contamination, a potentially significant issue in previous studies. GABA levels more rapidly declined with advancing age in the schizophrenia compared to the control group. Interventions targeted at halting the decline or increasing GABA levels may improve functional outcomes and quality of life as patients with schizophrenia age. PMID:25824298

Grand Challenge Problems in Real-Time Mission Control Systems for NASA's 21st Century Missions

NASA Technical Reports Server (NTRS)

Pfarr, Barbara B.; Donohue, John T.; Hughes, Peter M.

1999-01-01

Space missions of the 21st Century will be characterized by constellations of distributed spacecraft, miniaturized sensors and satellites, increased levels of automation, intelligent onboard processing, and mission autonomy. Programmatically, these missions will be noted for dramatically decreased budgets and mission development lifecycles. Current progress towards flexible, scaleable, low-cost, reusable mission control systems must accelerate given the current mission deployment schedule, and new technology will need to be infused to achieve desired levels of autonomy and processing capability. This paper will discuss current and future missions being managed at NASA's Goddard Space Flight Center in Greenbelt, MD. It will describe the current state of mission control systems and the problems they need to overcome to support the missions of the 21st Century.

A novel frame-level constant-distortion bit allocation for smooth H.264/AVC video quality

NASA Astrophysics Data System (ADS)

Liu, Li; Zhuang, Xinhua

2009-01-01

It is known that quality fluctuation has a major negative effect on visual perception. In previous work, we introduced a constant-distortion bit allocation method [1] for H.263+ encoder. However, the method in [1] can not be adapted to the newest H.264/AVC encoder directly as the well-known chicken-egg dilemma resulted from the rate-distortion optimization (RDO) decision process. To solve this problem, we propose a new two stage constant-distortion bit allocation (CDBA) algorithm with enhanced rate control for H.264/AVC encoder. In stage-1, the algorithm performs RD optimization process with a constant quantization QP. Based on prediction residual signals from stage-1 and target distortion for smooth video quality purpose, the frame-level bit target is allocated by using a close-form approximations of ratedistortion relationship similar to [1], and a fast stage-2 encoding process is performed with enhanced basic unit rate control. Experimental results show that, compared with original rate control algorithm provided by H.264/AVC reference software JM12.1, the proposed constant-distortion frame-level bit allocation scheme reduces quality fluctuation and delivers much smoother PSNR on all testing sequences.

Event-related potentials during visual selective attention in children of alcoholics.

PubMed

van der Stelt, O; Gunning, W B; Snel, J; Kok, A

1998-12-01

Event-related potentials were recorded from 7- to 18-year-old children of alcoholics (COAs, n = 50) and age- and sex-matched control children (n = 50) while they performed a visual selective attention task. The task was to attend selectively to stimuli with a specified color (red or blue) in an attempt to detect the occurrence of target stimuli. COAs manifested a smaller P3b amplitude to attended-target stimuli over the parietal and occipital scalp than did the controls. A more specific analysis indicated that both the attentional relevance and the target properties of the eliciting stimulus determined the observed P3b amplitude differences between COAs and controls. In contrast, no significant group differences were observed in attention-related earlier occurring event-related potential components, referred to as frontal selection positivity, selection negativity, and N2b. These results represent neurophysiological evidence that COAs suffer from deficits at a late (semantic) level of visual selective information processing that are unlikely a consequence of deficits at earlier (sensory) levels of selective processing. The findings support the notion that a reduced visual P3b amplitude in COAs represents a high-level processing dysfunction indicating their increased vulnerability to alcoholism.

Scheduling algorithms for automatic control systems for technological processes

NASA Astrophysics Data System (ADS)

Chernigovskiy, A. S.; Tsarev, R. Yu; Kapulin, D. V.

2017-01-01

Wide use of automatic process control systems and the usage of high-performance systems containing a number of computers (processors) give opportunities for creation of high-quality and fast production that increases competitiveness of an enterprise. Exact and fast calculations, control computation, and processing of the big data arrays - all of this requires the high level of productivity and, at the same time, minimum time of data handling and result receiving. In order to reach the best time, it is necessary not only to use computing resources optimally, but also to design and develop the software so that time gain will be maximal. For this purpose task (jobs or operations), scheduling techniques for the multi-machine/multiprocessor systems are applied. Some of basic task scheduling methods for the multi-machine process control systems are considered in this paper, their advantages and disadvantages come to light, and also some usage considerations, in case of the software for automatic process control systems developing, are made.

40 CFR 63.1362 - Standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... source subject to the provisions of this subpart shall control HAP emissions to the levels specified in... control device, installed on or before November 10, 1997 on a process vent otherwise subject to the... greater than or equal to 90 percent by weight but less than 98 percent by weight, then the control device...

40 CFR 63.1362 - Standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... source subject to the provisions of this subpart shall control HAP emissions to the levels specified in... control device, installed on or before November 10, 1997 on a process vent otherwise subject to the... greater than or equal to 90 percent by weight but less than 98 percent by weight, then the control device...

Mindfulness and Inhibitory Control in Early Adolescence

ERIC Educational Resources Information Center

Oberle, Eva; Schonert-Reichl, Kimberly A.; Lawlor, Molly Stewart; Thomson, Kimberly C.

2012-01-01

This study examined the relationship between the executive control process of inhibition and self-reported dispositional mindfulness, controlling for gender, grade, and cortisol levels in 99 (43% female) fourth- and fifth-graders ([X-bar] = 10.23 years, SD = 0.53). Students completed a measure of mindful attention awareness and a computerized…

40 CFR 420.21 - Specialized definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... control system that utilizes filters to remove iron-bearing particles (fines) from blast furnace or... level is 10 pg/L per EPA Method 1613B for water and wastewater samples. (d) The term pg/L means... pollution control system means an emission control system that utilizes water to clean process or furnace...

40 CFR 420.21 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... control system that utilizes filters to remove iron-bearing particles (fines) from blast furnace or... level is 10 pg/L per EPA Method 1613B for water and wastewater samples. (d) The term pg/L means... pollution control system means an emission control system that utilizes water to clean process or furnace...

40 CFR 420.21 - Specialized definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... control system that utilizes filters to remove iron-bearing particles (fines) from blast furnace or... level is 10 pg/L per EPA Method 1613B for water and wastewater samples. (d) The term pg/L means... pollution control system means an emission control system that utilizes water to clean process or furnace...

Deficits of congenital amusia beyond pitch: Evidence from impaired categorical perception of vowels in Cantonese-speaking congenital amusics

PubMed Central

Shao, Jing; Huang, Xunan

2017-01-01

Congenital amusia is a lifelong disorder of fine-grained pitch processing in music and speech. However, it remains unclear whether amusia is a pitch-specific deficit, or whether it affects frequency/spectral processing more broadly, such as the perception of formant frequency in vowels, apart from pitch. In this study, in order to illuminate the scope of the deficits, we compared the performance of 15 Cantonese-speaking amusics and 15 matched controls on the categorical perception of sound continua in four stimulus contexts: lexical tone, pure tone, vowel, and voice onset time (VOT). Whereas lexical tone, pure tone and vowel continua rely on frequency/spectral processing, the VOT continuum depends on duration/temporal processing. We found that the amusic participants performed similarly to controls in all stimulus contexts in the identification, in terms of the across-category boundary location and boundary width. However, the amusic participants performed systematically worse than controls in discriminating stimuli in those three contexts that depended on frequency/spectral processing (lexical tone, pure tone and vowel), whereas they performed normally when discriminating duration differences (VOT). These findings suggest that the deficit of amusia is probably not pitch specific, but affects frequency/spectral processing more broadly. Furthermore, there appeared to be differences in the impairment of frequency/spectral discrimination in speech and nonspeech contexts. The amusic participants exhibited less benefit in between-category discriminations than controls in speech contexts (lexical tone and vowel), suggesting reduced categorical perception; on the other hand, they performed inferiorly compared to controls across the board regardless of between- and within-category discriminations in nonspeech contexts (pure tone), suggesting impaired general auditory processing. These differences imply that the frequency/spectral-processing deficit might be manifested differentially in speech and nonspeech contexts in amusics—it is manifested as a deficit of higher-level phonological processing in speech sounds, and as a deficit of lower-level auditory processing in nonspeech sounds. PMID:28829808

The patient's perspective in the Dutch National Technical Agreement on Telemedicine.

PubMed

Meijer, Wouter J

2008-01-01

In 2007, the Dutch National Technical Agreement (NTA) for Telemedicine was established. Telemedicine deals with care processes. The goals of Telemedicine were defined broadly, including quality of life in non-medical terms as seen from the patient's perspective: 1) independence, 2) self-reliance; 3) participation in society and social life and 4) self-determination (autonomy through freedom of choice) for the care consumer and his environment. Quality aspects were defined at three levels:1) patient level Telemedicine must be in line with his needs. 2) level of information provision, such as: patient's rights in information control were also defined in the NTA: the care consumer has ultimate control over his own data. The care consumer decides who, in which functional capacity within the care process, is entitled to access which data at which level (reading) and is entitled to process it in some way: making additions, changes or possibly deleting (writing). On request, the healthcare provider must allow the care consumer access to his own data as quickly as possible and/or provide a copy of (part of) the record.3) level of business processes, e.g.it is important that the care process is designed on the basis of statutory requirements for the allocation and registration of the roles, rights and obligations of all actors concerned. For quality assurance, the processes must be defined on the basis of the function that they perform in the achievement of the goals (intended outcome), from the starting situation (input). The intended outcome means that the needs or requirements of the involved parties are fulfilled. The quality of the Telemedicine service must be assured in a cyclical and ongoing process. This can best be done by developing a quality management system based on indicators and criteria for quality.

The Impact of DMARD and Anti-TNF Therapy on Functional Characterization of Short-Term T-Cell Activation in Patients with Rheumatoid Arthritis – A Follow-Up Study

PubMed Central

Szalay, Balázs; Cseh, Áron; Mészáros, Gergő; Kovács, László; Balog, Attila; Vásárhelyi, Barna

2014-01-01

Rheumatoid arthritis (RA) is a chronic autoimmune disease characterized by a systemic dysfunction of T-cells. In this study we tested the impact of DMARD and anti-TNF agents on short-term activation characteristics of T-cells. We enrolled 12 patients with newly diagnosed RA (naïve RA) who were treated with methothrexate (MTX) and glucocorticsteroid (GCS) and 22 patients with established RA non responding to conventional DMARD therapy who were treated with different anti-TNF agents. Nine healthy volunteers served as controls. Blood samples were taken at baseline, then at 4th and 8th week of therapy. The characteristics of several intracellular activation processes during short-term activation of T-cells including cytoplasmic Ca2+ level, mitochondrial Ca2+ level, reactive oxygen species (ROS) and nitric oxide (NO) generation were determined by a novel flow-cytometry technique. At baseline, the tested processes were comparable to controls in naïve RA. During GCS therapy, cytoplasmic Ca2+ level and ROS generation decreased. After the addition of MTX to GCS cytoplasmic Ca2+ level became comparable to controls, while ROS generation decreased further. In DMARD non responders, cytoplasmic Ca2+ level was higher than controls at baseline. The cytoplasmic Ca2+ level became comparable to controls and ROS generation decreased during each of the three anti-TNF-α agent therapies. Mitochondrial Ca2+ level and NO generation were unaltered in all of the patient groups. These results indicate that intracellular machinery is affected in T-cells of RA patients. This may alter the behavior of T-cells during activation. Different therapeutic approaches may modulate the abnormal T-cell functions. PMID:25098248

The relationship between mood state and perceived control in contingency learning: effects of individualist and collectivist values.

PubMed

Msetfi, Rachel M; Kornbrot, Diana E; Matute, Helena; Murphy, Robin A

2015-01-01

Perceived control in contingency learning is linked to psychological wellbeing with low levels of perceived control thought to be a cause or consequence of depression and high levels of control considered to be the hallmark of mental healthiness. However, it is not clear whether this is a universal phenomenon or whether the value that people ascribe to control influences these relationships. Here we hypothesize that values affect learning about control contingencies and influence the relationship between perceived control and symptoms of mood disorders. We tested these hypotheses with European university samples who were categorized as endorsing (or not) values relevant to control-individualist and collectivist values. Three online experimental contingency learning studies (N 1 = 127, N 2 = 324, N 3 = 272) were carried out. Evidence suggested that individualist values influenced basic learning processes via an effect on learning about the context in which events took place. Participants who endorsed individualist values made control judgments that were more in line with an elemental associative learning model, whilst those who were ambivalent about individualist values made judgments that were more consistent with a configural process. High levels of perceived control and individualist values were directly associated with increased euphoric symptoms of bipolar disorder, and such values completely mediated the relation between perceived control and symptoms. The effect of low perceived control on depression was moderated by collectivist values. Anxiety created by dissonance between values and task may be a catalyst for developing mood symptoms. Conclusions are that values play a significant intermediary role in the relation between perceived control and symptoms of mood disturbance.

Tumor Necrosis Factor-Alpha and Interleukin 6 in Human Periapical Lesions

PubMed Central

Pršo, Ivana Brekalo; Kocjan, Willy; Šimić, Hrvoje; Brumini, Gordana; Pezelj-Ribarić, Sonja; Borčić, Josipa; Ferreri, Silvio; Karlović, Ivana Miletić

2007-01-01

Aim. The aim of this study was to evaluate the presence of the cytokines tumor necrosis factor-alpha (TNF-α) and interleukin-6 (IL-6) in human periapical lesions. Subjects and methods. Samples were obtained from three groups of teeth: symptomatic teeth, asymptomatic lesions, and uninflamed periradicular tissues as a control. Results. TNF-alpha levels were significantly increased in symptomatic lesions compared to control. Group with asymptomatic lesions had significantly higher concentrations compared to control. There were no significant differences in TNF-alpha levels between symptomatic and asymptomatic lesions. In group with symptomatic lesions, IL-6 levels were significantly higher than in group with asymptomatic lesions. The IL-6 levels in symptomatic group also showed significantly higher concentration in comparison with control group. In asymptomatic group, the IL-6 level had significantly higher concentrations compared to control. Conclusion. These results indicate that symptomatic lesions represent an immunologically active stage of disease, and asymptomatic lesions are the point from which the process advances toward healing. PMID:17497030

Implicit and Explicit Attitudes Predict Smoking Cessation: Moderating Effects of Experienced Failure to Control Smoking and Plans to Quit

PubMed Central

Chassin, Laurie; Presson, Clark C.; Sherman, Steven J.; Seo, Dong-Chul; Macy, Jon

2010-01-01

The current study tested implicit and explicit attitudes as prospective predictors of smoking cessation in a Midwestern community sample of smokers. Results showed that the effects of attitudes significantly varied with levels of experienced failure to control smoking and plans to quit. Explicit attitudes significantly predicted later cessation among those with low (but not high or average) levels of experienced failure to control smoking. Conversely, however, implicit attitudes significantly predicted later cessation among those with high levels of experienced failure to control smoking, but only if they had a plan to quit. Because smoking cessation involves both controlled and automatic processes, interventions may need to consider attitude change interventions that focus on both implicit and explicit attitudes. PMID:21198227

Impairment in local and global processing and set-shifting in body dysmorphic disorder

PubMed Central

Kerwin, Lauren; Hovav, Sarit; Helleman, Gerhard; Feusner, Jamie D.

2014-01-01

Body dysmorphic disorder (BDD) is characterized by distressing and often debilitating preoccupations with misperceived defects in appearance. Research suggests that aberrant visual processing may contribute to these misperceptions. This study used two tasks to probe global and local visual processing as well as set shifting in individuals with BDD. Eighteen unmedicated individuals with BDD and 17 non-clinical controls completed two global-local tasks. The embedded figures task requires participants to determine which of three complex figures contained a simpler figure embedded within it. The Navon task utilizes incongruent stimuli comprised of a large letter (global level) made up of smaller letters (local level). The outcome measures were response time and accuracy rate. On the embedded figures task, BDD individuals were slower and less accurate than controls. On the Navon task, BDD individuals processed both global and local stimuli slower and less accurately than controls, and there was a further decrement in performance when shifting attention between the different levels of stimuli. Worse insight correlated with poorer performance on both tasks. Taken together, these results suggest abnormal global and local processing for non-appearance related stimuli among BDD individuals, in addition to evidence of poor set-shifting abilities. Moreover, these abnormalities appear to relate to the important clinical variable of poor insight. Further research is needed to explore these abnormalities and elucidate their possible role in the development and/or persistence of BDD symptoms. PMID:24972487

A comprehensive model to evaluate implementation of the world health organization framework convention of tobacco control

PubMed Central

Sarrafzadegan, Nizal; Kelishad, Roya; Rabiei, Katayoun; Abedi, Heidarali; Mohaseli, Khadijeh Fereydoun; Masooleh, Hasan Azaripour; Alavi, Mousa; Heidari, Gholamreza; Ghaffari, Mostafa; O’Loughlin, Jennifer

2012-01-01

Background: Iran is one of the countries that has ratified the World Health Organization Framework Convention of Tobacco Control (WHO-FCTC), and has implemented a series of tobacco control interventions including the Comprehensive Tobacco Control Law. Enforcement of this legislation and assessment of its outcome requires a dedicated evaluation system. This study aimed to develop a generic model to evaluate the implementation of the Comprehensive Tobacco Control Law in Iran that was provided based on WHO-FCTC articles. Materials and Methods: Using a grounded theory approach, qualitative data were collected from 265 subjects in individual interviews and focus group discussions with policymakers who designed the legislation, key stakeholders, and members of the target community. In addition, field observations data in supermarkets/shops, restaurants, teahouses and coffee shops were collected. Data were analyzed in two stages through conceptual theoretical coding. Findings: Overall, 617 open codes were extracted from the data into tables; 72 level-3 codes were retained from the level-2 code series. Using a Model Met paradigm, the relationships between the components of each paradigm were depicted graphically. The evaluation model entailed three levels, namely: short-term results, process evaluation and long-term results. Conclusions: Central concept of the process of evaluation is that enforcing the law influences a variety of internal and environmental factors including legislative changes. These factors will be examined during the process evaluation and context evaluation. The current model can be applicable for providing FCTC evaluation tools across other jurisdictions. PMID:23833621

Load-dependent dysfunction of the putamen during attentional processing in patients with clinically isolated syndrome suggestive of multiple sclerosis.

PubMed

Tortorella, C; Romano, R; Direnzo, V; Taurisano, P; Zoccolella, S; Iaffaldano, P; Fazio, L; Viterbo, R; Popolizio, T; Blasi, G; Bertolino, A; Trojano, M

2013-08-01

Load-related functional magnetic resonance imaging (fMRI) abnormalities of brain activity during performance of attention tasks have been described in definite multiple sclerosis (MS). No data are available in clinically isolated syndrome (CIS) suggestive of MS. The objective of this research is to evaluate in CIS patients the fMRI pattern of brain activation during an attention task and to explore the effect of increasing task load demand on neurofunctional modifications. Twenty-seven untreated CIS patients and 32 age- and sex-matched healthy controls (HCs) underwent fMRI while performing the Variable Attentional Control (VAC) task, a cognitive paradigm requiring increasing levels of attentional control processing. Random-effects models were used for statistical analyses of fMRI data. CIS patients had reduced accuracy and greater reaction time at the VAC task compared with HCs (p=0.007). On blood oxygenation level-dependent (BOLD)-fMRI, CIS patients had greater activity in the right parietal cortex (p=0.0004) compared with HCs. Furthermore, CIS patients had greater activity at the lower (p=0.05) and reduced activity at the greater (p=0.04) level of attentional control demand in the left putamen, compared with HCs. This study demonstrates the failure of attentional control processing in CIS. The load-related fMRI dysfunction of the putamen supports the role of basal ganglia in the failure of attention observed at the earliest stage of MS.

Executive control over unconscious cognition: attentional sensitization of unconscious information processing

PubMed Central

Kiefer, Markus

2012-01-01

Unconscious priming is a prototypical example of an automatic process, which is initiated without deliberate intention. Classical theories of automaticity assume that such unconscious automatic processes occur in a purely bottom-up driven fashion independent of executive control mechanisms. In contrast to these classical theories, our attentional sensitization model of unconscious information processing proposes that unconscious processing is susceptible to executive control and is only elicited if the cognitive system is configured accordingly. It is assumed that unconscious processing depends on attentional amplification of task-congruent processing pathways as a function of task sets. This article provides an overview of the latest research on executive control influences on unconscious information processing. I introduce refined theories of automaticity with a particular focus on the attentional sensitization model of unconscious cognition which is specifically developed to account for various attentional influences on different types of unconscious information processing. In support of the attentional sensitization model, empirical evidence is reviewed demonstrating executive control influences on unconscious cognition in the domains of visuo-motor and semantic processing: subliminal priming depends on attentional resources, is susceptible to stimulus expectations and is influenced by action intentions and task sets. This suggests that even unconscious processing is flexible and context-dependent as a function of higher-level executive control settings. I discuss that the assumption of attentional sensitization of unconscious information processing can accommodate conflicting findings regarding the automaticity of processes in many areas of cognition and emotion. This theoretical view has the potential to stimulate future research on executive control of unconscious processing in healthy and clinical populations. PMID:22470329

Executive control over unconscious cognition: attentional sensitization of unconscious information processing.

PubMed

Kiefer, Markus

2012-01-01

Unconscious priming is a prototypical example of an automatic process, which is initiated without deliberate intention. Classical theories of automaticity assume that such unconscious automatic processes occur in a purely bottom-up driven fashion independent of executive control mechanisms. In contrast to these classical theories, our attentional sensitization model of unconscious information processing proposes that unconscious processing is susceptible to executive control and is only elicited if the cognitive system is configured accordingly. It is assumed that unconscious processing depends on attentional amplification of task-congruent processing pathways as a function of task sets. This article provides an overview of the latest research on executive control influences on unconscious information processing. I introduce refined theories of automaticity with a particular focus on the attentional sensitization model of unconscious cognition which is specifically developed to account for various attentional influences on different types of unconscious information processing. In support of the attentional sensitization model, empirical evidence is reviewed demonstrating executive control influences on unconscious cognition in the domains of visuo-motor and semantic processing: subliminal priming depends on attentional resources, is susceptible to stimulus expectations and is influenced by action intentions and task sets. This suggests that even unconscious processing is flexible and context-dependent as a function of higher-level executive control settings. I discuss that the assumption of attentional sensitization of unconscious information processing can accommodate conflicting findings regarding the automaticity of processes in many areas of cognition and emotion. This theoretical view has the potential to stimulate future research on executive control of unconscious processing in healthy and clinical populations.

Speed control of an induction motor by 6-switched 3-level inverter

NASA Astrophysics Data System (ADS)

Saygin, Ali; Kerem, Alper

2017-12-01

This paper presents speed control analysis of an induction motor by a 6-switched 3-level inverter. In the analysis of topology, the study used the field oriented control technique which is widely used in the literature, easy and stable for operating systems. The field weaking technique was used for speeds exceeding nominal speed to reduce magnetic saturation and thermal losses. At the end of the process, it was observed to increase motor torque and inverter efficiency. Instead of using 12 switches in conventional 3-level inverters, 6 switches are used in this topology. Reduced number of switches is the greatest contribution of this study.

An engineering approach to modelling, decision support and control for sustainable systems.

PubMed

Day, W; Audsley, E; Frost, A R

2008-02-12

Engineering research and development contributes to the advance of sustainable agriculture both through innovative methods to manage and control processes, and through quantitative understanding of the operation of practical agricultural systems using decision models. This paper describes how an engineering approach, drawing on mathematical models of systems and processes, contributes new methods that support decision making at all levels from strategy and planning to tactics and real-time control. The ability to describe the system or process by a simple and robust mathematical model is critical, and the outputs range from guidance to policy makers on strategic decisions relating to land use, through intelligent decision support to farmers and on to real-time engineering control of specific processes. Precision in decision making leads to decreased use of inputs, less environmental emissions and enhanced profitability-all essential to sustainable systems.

High-level recombinant protein expression in transgenic plants by using a double-inducible viral vector

PubMed Central

Werner, Stefan; Breus, Oksana; Symonenko, Yuri; Marillonnet, Sylvestre; Gleba, Yuri

2011-01-01

We describe here a unique ethanol-inducible process for expression of recombinant proteins in transgenic plants. The process is based on inducible release of viral RNA replicons from stably integrated DNA proreplicons. A simple treatment with ethanol releases the replicon leading to RNA amplification and high-level protein production. To achieve tight control of replicon activation and spread in the uninduced state, the viral vector has been deconstructed, and its two components, the replicon and the cell-to-cell movement protein, have each been placed separately under the control of an inducible promoter. Transgenic Nicotiana benthamiana plants incorporating this double-inducible system demonstrate negligible background expression, high (over 0.5 × 104-fold) induction multiples, and high absolute levels of protein expression upon induction (up to 4.3 mg/g fresh biomass). The process can be easily scaled up, supports expression of practically important recombinant proteins, and thus can be directly used for industrial manufacturing. PMID:21825158

Discourse changes in early Alzheimer disease, mild cognitive impairment, and normal aging.

PubMed

Chapman, Sandra Bond; Zientz, Jennifer; Weiner, Myron; Rosenberg, Roger; Frawley, William; Burns, Mary Hope

2002-01-01

The purpose of this study was to determine the sensitivity of discourse gist measures to the early cognitive-linguistic changes in Alzheimer disease (AD) and in the preclinical stages. Differences in discourse abilities were examined in 25 cognitively normal adults, 24 adults with mild probable AD, and 20 adults with mild cognitive impairment (MCI) at gist and detail levels of discourse processing. The authors found that gist and detail levels of discourse processing were significantly impaired in persons with AD and MCI as compared with normal control subjects. Gist-level discourse processing abilities showed minimal overlap between cognitively normal control subjects and those with mild AD. Moreover, the majority of the persons with MCI performed in the range of AD on gist measures. These findings indicate that discourse gist measures hold promise as a diagnostic complement to enhance early detection of AD. Further studies are needed to determine how early the discourse gist deficits arise in AD.

Contextual control over task-set retrieval.

PubMed

Crump, Matthew J C; Logan, Gordon D

2010-11-01

Contextual cues signaling task likelihood or the likelihood of task repetition are known to modulate the size of switch costs. We follow up on the finding by Leboe, Wong, Crump, and Stobbe (2008) that location cues predictive of the proportion of switch or repeat trials modulate switch costs. Their design employed one cue per task, whereas our experiment employed two cues per task, which allowed separate assessment of modulations to the cue-repetition benefit, a measure of lower level cue-encoding processes, and to the task-alternation cost, a measure of higher level processes representing task-set information. We demonstrate that location information predictive of switch proportion modulates performance at the level of task-set representations. Furthermore, we demonstrate that contextual control occurs even when subjects are unaware of the associations between context and switch likelihood. We discuss the notion that contextual information provides rapid, unconscious control over the extent to which prior task-set representations are retrieved in the service of guiding online performance.

An embedded vision system for an unmanned four-rotor helicopter

NASA Astrophysics Data System (ADS)

Lillywhite, Kirt; Lee, Dah-Jye; Tippetts, Beau; Fowers, Spencer; Dennis, Aaron; Nelson, Brent; Archibald, James

2006-10-01

In this paper an embedded vision system and control module is introduced that is capable of controlling an unmanned four-rotor helicopter and processing live video for various law enforcement, security, military, and civilian applications. The vision system is implemented on a newly designed compact FPGA board (Helios). The Helios board contains a Xilinx Virtex-4 FPGA chip and memory making it capable of implementing real time vision algorithms. A Smooth Automated Intelligent Leveling daughter board (SAIL), attached to the Helios board, collects attitude and heading information to be processed in order to control the unmanned helicopter. The SAIL board uses an electrolytic tilt sensor, compass, voltage level converters, and analog to digital converters to perform its operations. While level flight can be maintained, problems stemming from the characteristics of the tilt sensor limits maneuverability of the helicopter. The embedded vision system has proven to give very good results in its performance of a number of real-time robotic vision algorithms.

Effect of posttraumatic stress on study time in a task measuring four component processes underlying text-level reading.

PubMed

Sullivan, Michael P; Griffiths, Gina G; Moore Sohlberg, Mckay

2014-10-01

To investigate the effect of combat-related posttraumatic stress disorder (PTSD) on 4 components underlying text-level reading comprehension. A group of 17 veterans with PTSD and 17 matched control participants took part. An experimental task required participants to read and study 3-sentence paragraphs describing semantic features associated with real and unreal objects. Each paragraph was followed by true-false statements that assessed knowledge access, text memory, inference, and integration. The results revealed that the PTSD group took significantly longer than the control group to study the paragraphs. Although there was no group difference in test statement accuracy, the PTSD group also took significantly longer to respond to the test statements. Overall, the results provide evidence for the control theory of attention but suggest that more direct measures of task-irrelevant processing during text-level reading are needed. More important, the results begin to lay a foundation for developing not only diagnostic but also intervention strategies.

Advanced I&C for Fault-Tolerant Supervisory Control of Small Modular Reactors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cole, Daniel G.

In this research, we have developed a supervisory control approach to enable automated control of SMRs. By design the supervisory control system has an hierarchical, interconnected, adaptive control architecture. A considerable advantage to this architecture is that it allows subsystems to communicate at different/finer granularity, facilitates monitoring of process at the modular and plant levels, and enables supervisory control. We have investigated the deployment of automation, monitoring, and data collection technologies to enable operation of multiple SMRs. Each unit's controller collects and transfers information from local loops and optimize that unit’s parameters. Information is passed from the each SMR unitmore » controller to the supervisory controller, which supervises the actions of SMR units and manage plant processes. The information processed at the supervisory level will provide operators the necessary information needed for reactor, unit, and plant operation. In conjunction with the supervisory effort, we have investigated techniques for fault-tolerant networks, over which information is transmitted between local loops and the supervisory controller to maintain a safe level of operational normalcy in the presence of anomalies. The fault-tolerance of the supervisory control architecture, the network that supports it, and the impact of fault-tolerance on multi-unit SMR plant control has been a second focus of this research. To this end, we have investigated the deployment of advanced automation, monitoring, and data collection and communications technologies to enable operation of multiple SMRs. We have created a fault-tolerant multi-unit SMR supervisory controller that collects and transfers information from local loops, supervise their actions, and adaptively optimize the controller parameters. The goal of this research has been to develop the methodologies and procedures for fault-tolerant supervisory control of small modular reactors. To achieve this goal, we have identified the following objectives. These objective are an ordered approach to the research: I) Development of a supervisory digital I&C system II) Fault-tolerance of the supervisory control architecture III) Automated decision making and online monitoring.« less

Neighborhood-Level Social Processes and Substantiated Cases of Child Maltreatment

PubMed Central

Molnar, Beth E.; Goerge, Robert M.; Gilsanz, Paola; Hill, Andrea; Subramanian, SV; Holton, John K.; Duncan, Dustin T.; Beatriz, Elizabeth D.; Beardslee, William R.

2015-01-01

Child maltreatment is a preventable public health problem. Research has demonstrated that neighborhood structural factors (e.g. poverty, crime) can influence the proportion of a neighborhood’s children who are victims of maltreatment. A newer strategy is the identification of potentially modifiable social processes at the neighborhood level that can also influence maltreatment. Toward this end, this study examines neighborhood-level data (maltreatment cases substantiated by Illinois’ child protection agency, 1995–2005, social processes measured by the Project on Human Development in Chicago Neighborhoods, U.S. Census data, proportions of neighborhoods on public assistance, and crime data) that were linked across clusters of contiguous, relatively homogenous Chicago, IL census tracts with respect to racial/ethnic and socioeconomic composition. Our analysis—an ecological-level, repeated cross-sectional design utilizing random-intercept logit models— with a sensitivity analysis using spatial models to control for spatial autocorrelation – revealed consistent associations between neighborhood social processes and maltreatment. Neighborhoods higher in collective efficacy, intergenerational closure, and social networks, and lower in disorder had lower proportions of neglect, physical abuse, and sexual abuse substantiated cases, controlling for differences in structural factors. Higher collective efficacy and social network size also predicted a lower proportion of substance-exposed infants. This research indicates that strategies to mobilize neighborhood-level protective factors may decrease child maltreatment more effectively than individual and family-focused efforts alone. PMID:26684963

Neighborhood-level social processes and substantiated cases of child maltreatment.

PubMed

Molnar, Beth E; Goerge, Robert M; Gilsanz, Paola; Hill, Andrea; Subramanian, S V; Holton, John K; Duncan, Dustin T; Beatriz, Elizabeth D; Beardslee, William R

2016-01-01

Child maltreatment is a preventable public health problem. Research has demonstrated that neighborhood structural factors (e.g. poverty, crime) can influence the proportion of a neighborhood's children who are victims of maltreatment. A newer strategy is the identification of potentially modifiable social processes at the neighborhood level that can also influence maltreatment. Toward this end, this study examines neighborhood-level data (maltreatment cases substantiated by Illinois' child protection agency, 1995-2005, social processes measured by the Project on Human Development in Chicago Neighborhoods, U.S. Census data, proportions of neighborhoods on public assistance, and crime data) that were linked across clusters of contiguous, relatively homogenous Chicago, IL census tracts with respect to racial/ethnic and socioeconomic composition. Our analysis-an ecological-level, repeated cross-sectional design utilizing random-intercept logit models-with a sensitivity analysis using spatial models to control for spatial autocorrelation-revealed consistent associations between neighborhood social processes and maltreatment. Neighborhoods higher in collective efficacy, intergenerational closure, and social networks, and lower in disorder had lower proportions of neglect, physical abuse, and sexual abuse substantiated cases, controlling for differences in structural factors. Higher collective efficacy and social network size also predicted a lower proportion of substance-exposed infants. This research indicates that strategies to mobilize neighborhood-level protective factors may decrease child maltreatment more effectively than individual and family-focused efforts alone. Copyright © 2015 Elsevier Ltd. All rights reserved.

Supportability Technologies for Future Exploration Missions

NASA Technical Reports Server (NTRS)

Watson, Kevin; Thompson, Karen

2007-01-01

Future long-duration human exploration missions will be challenged by resupply limitations and mass and volume constraints. Consequently, it will be essential that the logistics footprint required to support these missions be minimized and that capabilities be provided to make them highly autonomous from a logistics perspective. Strategies to achieve these objectives include broad implementation of commonality and standardization at all hardware levels and across all systems, repair of failed hardware at the lowest possible hardware level, and manufacture of structural and mechanical replacement components as needed. Repair at the lowest hardware levels will require the availability of compact, portable systems for diagnosis of failures in electronic systems and verification of system functionality following repair. Rework systems will be required that enable the removal and replacement of microelectronic components with minimal human intervention to minimize skill requirements and training demand for crews. Materials used in the assembly of electronic systems (e.g. solders, fluxes, conformal coatings) must be compatible with the available repair methods and the spacecraft environment. Manufacturing of replacement parts for structural and mechanical applications will require additive manufacturing systems that can generate near-net-shape parts from the range of engineering alloys employed in the spacecraft structure and in the parts utilized in other surface systems. These additive manufacturing processes will need to be supported by real-time non-destructive evaluation during layer-additive processing for on-the-fly quality control. This will provide capabilities for quality control and may serve as an input for closed-loop process control. Additionally, non-destructive methods should be available for material property determination. These nondestructive evaluation processes should be incorporated with the additive manufacturing process - providing an in-process capability to ensure that material deposited during layer-additive processing meets required material property criteria.

Addiction, adolescence, and the integration of control and motivation.

PubMed

Gladwin, Thomas E; Figner, Bernd; Crone, Eveline A; Wiers, Reinout W

2011-10-01

The likelihood of initiating addictive behaviors is higher during adolescence than during any other developmental period. The differential developmental trajectories of brain regions involved in motivation and control processes may lead to adolescents' increased risk taking in general, which may be exacerbated by the neural consequences of drug use. Neuroimaging studies suggest that increased risk-taking behavior in adolescence is related to an imbalance between prefrontal cortical regions, associated with executive functions, and subcortical brain regions related to affect and motivation. Dual-process models of addictive behaviors are similarly concerned with difficulties in controlling abnormally strong motivational processes. We acknowledge concerns raised about dual-process models, but argue that they can be addressed by carefully considering levels of description: motivational processes and top-down biasing can be understood as intertwined, co-developing components of more versus less reflective states of processing. We illustrate this with a model that further emphasizes temporal dynamics. Finally, behavioral interventions for addiction are discussed. Insights in the development of control and motivation may help to better understand - and more efficiently intervene in - vulnerabilities involving control and motivation. Copyright © 2011 Elsevier Ltd. All rights reserved.

Sigma metrics as a tool for evaluating the performance of internal quality control in a clinical chemistry laboratory.

PubMed

Kumar, B Vinodh; Mohan, Thuthi

2018-01-01

Six Sigma is one of the most popular quality management system tools employed for process improvement. The Six Sigma methods are usually applied when the outcome of the process can be measured. This study was done to assess the performance of individual biochemical parameters on a Sigma Scale by calculating the sigma metrics for individual parameters and to follow the Westgard guidelines for appropriate Westgard rules and levels of internal quality control (IQC) that needs to be processed to improve target analyte performance based on the sigma metrics. This is a retrospective study, and data required for the study were extracted between July 2015 and June 2016 from a Secondary Care Government Hospital, Chennai. The data obtained for the study are IQC - coefficient of variation percentage and External Quality Assurance Scheme (EQAS) - Bias% for 16 biochemical parameters. For the level 1 IQC, four analytes (alkaline phosphatase, magnesium, triglyceride, and high-density lipoprotein-cholesterol) showed an ideal performance of ≥6 sigma level, five analytes (urea, total bilirubin, albumin, cholesterol, and potassium) showed an average performance of <3 sigma level and for level 2 IQCs, same four analytes of level 1 showed a performance of ≥6 sigma level, and four analytes (urea, albumin, cholesterol, and potassium) showed an average performance of <3 sigma level. For all analytes <6 sigma level, the quality goal index (QGI) was <0.8 indicating the area requiring improvement to be imprecision except cholesterol whose QGI >1.2 indicated inaccuracy. This study shows that sigma metrics is a good quality tool to assess the analytical performance of a clinical chemistry laboratory. Thus, sigma metric analysis provides a benchmark for the laboratory to design a protocol for IQC, address poor assay performance, and assess the efficiency of existing laboratory processes.

Patterned wafer geometry grouping for improved overlay control

NASA Astrophysics Data System (ADS)

Lee, Honggoo; Han, Sangjun; Woo, Jaeson; Park, Junbeom; Song, Changrock; Anis, Fatima; Vukkadala, Pradeep; Jeon, Sanghuck; Choi, DongSub; Huang, Kevin; Heo, Hoyoung; Smith, Mark D.; Robinson, John C.

2017-03-01

Process-induced overlay errors from outside the litho cell have become a significant contributor to the overlay error budget including non-uniform wafer stress. Previous studies have shown the correlation between process-induced stress and overlay and the opportunity for improvement in process control, including the use of patterned wafer geometry (PWG) metrology to reduce stress-induced overlay signatures. Key challenges of volume semiconductor manufacturing are how to improve not only the magnitude of these signatures, but also the wafer to wafer variability. This work involves a novel technique of using PWG metrology to provide improved litho-control by wafer-level grouping based on incoming process induced overlay, relevant for both 3D NAND and DRAM. Examples shown in this study are from 19 nm DRAM manufacturing.

A Review of International Space Station Habitable Element Equipment Offgassing Characteristics

NASA Technical Reports Server (NTRS)

Perry, Jay L.

2010-01-01

Crewed spacecraft trace contaminant control employs both passive and active methods to achieve acceptable cabin atmospheric quality. Passive methods include carefully selecting materials of construction, employing clean manufacturing practices, and minimizing systems and payload operational impacts to the cabin environment. Materials selection and manufacturing processes constitute the first level of equipment offgassing control. An element-level equipment offgassing test provides preflight verification that passive controls have been successful. Offgassing test results from multiple International Space Station (ISS) habitable elements and cargo vehicles are summarized and implications for active contamination control equipment design are discussed

Modeling laser velocimeter signals as triply stochastic Poisson processes

NASA Technical Reports Server (NTRS)

Mayo, W. T., Jr.

1976-01-01

Previous models of laser Doppler velocimeter (LDV) systems have not adequately described dual-scatter signals in a manner useful for analysis and simulation of low-level photon-limited signals. At low photon rates, an LDV signal at the output of a photomultiplier tube is a compound nonhomogeneous filtered Poisson process, whose intensity function is another (slower) Poisson process with the nonstationary rate and frequency parameters controlled by a random flow (slowest) process. In the present paper, generalized Poisson shot noise models are developed for low-level LDV signals. Theoretical results useful in detection error analysis and simulation are presented, along with measurements of burst amplitude statistics. Computer generated simulations illustrate the difference between Gaussian and Poisson models of low-level signals.

Statistical process control and verifying positional accuracy of a cobra motion couch using step-wedge quality assurance tool.

PubMed

Binny, Diana; Lancaster, Craig M; Trapp, Jamie V; Crowe, Scott B

2017-09-01

This study utilizes process control techniques to identify action limits for TomoTherapy couch positioning quality assurance tests. A test was introduced to monitor accuracy of the applied couch offset detection in the TomoTherapy Hi-Art treatment system using the TQA "Step-Wedge Helical" module and MVCT detector. Individual X-charts, process capability (cp), probability (P), and acceptability (cpk) indices were used to monitor a 4-year couch IEC offset data to detect systematic and random errors in the couch positional accuracy for different action levels. Process capability tests were also performed on the retrospective data to define tolerances based on user-specified levels. A second study was carried out whereby physical couch offsets were applied using the TQA module and the MVCT detector was used to detect the observed variations. Random and systematic variations were observed for the SPC-based upper and lower control limits, and investigations were carried out to maintain the ongoing stability of the process for a 4-year and a three-monthly period. Local trend analysis showed mean variations up to ±0.5 mm in the three-monthly analysis period for all IEC offset measurements. Variations were also observed in the detected versus applied offsets using the MVCT detector in the second study largely in the vertical direction, and actions were taken to remediate this error. Based on the results, it was recommended that imaging shifts in each coordinate direction be only applied after assessing the machine for applied versus detected test results using the step helical module. User-specified tolerance levels of at least ±2 mm were recommended for a test frequency of once every 3 months to improve couch positional accuracy. SPC enables detection of systematic variations prior to reaching machine tolerance levels. Couch encoding system recalibrations reduced variations to user-specified levels and a monitoring period of 3 months using SPC facilitated in detecting systematic and random variations. SPC analysis for couch positional accuracy enabled greater control in the identification of errors, thereby increasing confidence levels in daily treatment setups. © 2017 Royal Brisbane and Women's Hospital, Metro North Hospital and Health Service. Journal of Applied Clinical Medical Physics published by Wiley Periodicals, Inc. on behalf of American Association of Physicists in Medicine.

Observation and quantification of the quantum dynamics of a strong-field excited multi-level system.

PubMed

Liu, Zuoye; Wang, Quanjun; Ding, Jingjie; Cavaletto, Stefano M; Pfeifer, Thomas; Hu, Bitao

2017-01-04

The quantum dynamics of a V-type three-level system, whose two resonances are first excited by a weak probe pulse and subsequently modified by another strong one, is studied. The quantum dynamics of the multi-level system is closely related to the absorption spectrum of the transmitted probe pulse and its modification manifests itself as a modulation of the absorption line shape. Applying the dipole-control model, the modulation induced by the second strong pulse to the system's dynamics is quantified by eight intensity-dependent parameters, describing the self and inter-state contributions. The present study opens the route to control the quantum dynamics of multi-level systems and to quantify the quantum-control process.

Benchmark Simulation Model No 2: finalisation of plant layout and default control strategy.

PubMed

Nopens, I; Benedetti, L; Jeppsson, U; Pons, M-N; Alex, J; Copp, J B; Gernaey, K V; Rosen, C; Steyer, J-P; Vanrolleghem, P A

2010-01-01

The COST/IWA Benchmark Simulation Model No 1 (BSM1) has been available for almost a decade. Its primary purpose has been to create a platform for control strategy benchmarking of activated sludge processes. The fact that the research work related to the benchmark simulation models has resulted in more than 300 publications worldwide demonstrates the interest in and need of such tools within the research community. Recent efforts within the IWA Task Group on "Benchmarking of control strategies for WWTPs" have focused on an extension of the benchmark simulation model. This extension aims at facilitating control strategy development and performance evaluation at a plant-wide level and, consequently, includes both pretreatment of wastewater as well as the processes describing sludge treatment. The motivation for the extension is the increasing interest and need to operate and control wastewater treatment systems not only at an individual process level but also on a plant-wide basis. To facilitate the changes, the evaluation period has been extended to one year. A prolonged evaluation period allows for long-term control strategies to be assessed and enables the use of control handles that cannot be evaluated in a realistic fashion in the one week BSM1 evaluation period. In this paper, the finalised plant layout is summarised and, as was done for BSM1, a default control strategy is proposed. A demonstration of how BSM2 can be used to evaluate control strategies is also given.

Integrated orbit and attitude hardware-in-the-loop simulations for autonomous satellite formation flying

NASA Astrophysics Data System (ADS)

Park, Han-Earl; Park, Sang-Young; Kim, Sung-Woo; Park, Chandeok

2013-12-01

Development and experiment of an integrated orbit and attitude hardware-in-the-loop (HIL) simulator for autonomous satellite formation flying are presented. The integrated simulator system consists of an orbit HIL simulator for orbit determination and control, and an attitude HIL simulator for attitude determination and control. The integrated simulator involves four processes (orbit determination, orbit control, attitude determination, and attitude control), which interact with each other in the same way as actual flight processes do. Orbit determination is conducted by a relative navigation algorithm using double-difference GPS measurements based on the extended Kalman filter (EKF). Orbit control is performed by a state-dependent Riccati equation (SDRE) technique that is utilized as a nonlinear controller for the formation control problem. Attitude is determined from an attitude heading reference system (AHRS) sensor, and a proportional-derivative (PD) feedback controller is used to control the attitude HIL simulator using three momentum wheel assemblies. Integrated orbit and attitude simulations are performed for a formation reconfiguration scenario. By performing the four processes adequately, the desired formation reconfiguration from a baseline of 500-1000 m was achieved with meter-level position error and millimeter-level relative position navigation. This HIL simulation demonstrates the performance of the integrated HIL simulator and the feasibility of the applied algorithms in a real-time environment. Furthermore, the integrated HIL simulator system developed in the current study can be used as a ground-based testing environment to reproduce possible actual satellite formation operations.

Development of advanced Czochralski growth process to produce low cost 150 kg silicon ingots from a single crucible for technology readiness

NASA Technical Reports Server (NTRS)

1980-01-01

The design and development of an advanced Czochralski crystal grower are described. Several exhaust gas analysis system equipment specifications studied are discussed. Process control requirements were defined and design work began on the melt temperature, melt level, and continuous diameter control. Sensor development included assembly and testing of a bench prototype of a diameter scanner system.

Community participation in malaria control strategy of intersect oral collaboration in Ghana: Myth or reality?

PubMed Central

2014-01-01

Abstract Background For many years, malaria has been one of the main health concerns of the government of Ghana. The government has recently implemented a control strategy which will ensure the inclusion of the community members who were previously excluded from the process. Until now, however, scientific study on this strategy has been scanty. Objectives The objectives were to investigate the level at which communities have been allowed to participate and to understand whether the idea of community participation in malaria control strategy is a myth or a reality. Methods Data were collected in the rural district of Ahafo-Ano South in the Ashanti region of Ghana. An exploratory qualitative approach was employed in order to ascertain the opinions of the local health officials and community members. The level of participation was measured using the framework of Arnstein's ‘ladder’ of participation, as developed in 1969. Results Evidence showed that the level of community participation was only tokenistic. Communities were only informed and/or consulted after decisions had been made, but the real engagement and negotiations were absent. Communities thus had limited opportunities to air their views in the planning process. Conclusion This article has revealed that the government's vision of ensuring community participation in the malaria control policy-making process can be said to be a myth rather than a reality. PMID:26245403

Intonation processing deficits of emotional words among Mandarin Chinese speakers with congenital amusia: an ERP study.

PubMed

Lu, Xuejing; Ho, Hao Tam; Liu, Fang; Wu, Daxing; Thompson, William F

2015-01-01

Congenital amusia is a disorder that is known to affect the processing of musical pitch. Although individuals with amusia rarely show language deficits in daily life, a number of findings point to possible impairments in speech prosody that amusic individuals may compensate for by drawing on linguistic information. Using EEG, we investigated (1) whether the processing of speech prosody is impaired in amusia and (2) whether emotional linguistic information can compensate for this impairment. Twenty Chinese amusics and 22 matched controls were presented pairs of emotional words spoken with either statement or question intonation while their EEG was recorded. Their task was to judge whether the intonations were the same. Amusics exhibited impaired performance on the intonation-matching task for emotional linguistic information, as their performance was significantly worse than that of controls. EEG results showed a reduced N2 response to incongruent intonation pairs in amusics compared with controls, which likely reflects impaired conflict processing in amusia. However, our EEG results also indicated that amusics were intact in early sensory auditory processing, as revealed by a comparable N1 modulation in both groups. We propose that the impairment in discriminating speech intonation observed among amusic individuals may arise from an inability to access information extracted at early processing stages. This, in turn, could reflect a disconnection between low-level and high-level processing.

Intonation processing deficits of emotional words among Mandarin Chinese speakers with congenital amusia: an ERP study

PubMed Central

Lu, Xuejing; Ho, Hao Tam; Liu, Fang; Wu, Daxing; Thompson, William F.

2015-01-01

Background: Congenital amusia is a disorder that is known to affect the processing of musical pitch. Although individuals with amusia rarely show language deficits in daily life, a number of findings point to possible impairments in speech prosody that amusic individuals may compensate for by drawing on linguistic information. Using EEG, we investigated (1) whether the processing of speech prosody is impaired in amusia and (2) whether emotional linguistic information can compensate for this impairment. Method: Twenty Chinese amusics and 22 matched controls were presented pairs of emotional words spoken with either statement or question intonation while their EEG was recorded. Their task was to judge whether the intonations were the same. Results: Amusics exhibited impaired performance on the intonation-matching task for emotional linguistic information, as their performance was significantly worse than that of controls. EEG results showed a reduced N2 response to incongruent intonation pairs in amusics compared with controls, which likely reflects impaired conflict processing in amusia. However, our EEG results also indicated that amusics were intact in early sensory auditory processing, as revealed by a comparable N1 modulation in both groups. Conclusion: We propose that the impairment in discriminating speech intonation observed among amusic individuals may arise from an inability to access information extracted at early processing stages. This, in turn, could reflect a disconnection between low-level and high-level processing. PMID:25914659

Manipulating Color and Other Visual Information Influences Picture Naming at Different Levels of Processing: Evidence from Alzheimer Subjects and Normal Controls

ERIC Educational Resources Information Center

Zannino, Gian Daniele; Perri, Roberta; Salamone, Giovanna; Di Lorenzo, Concetta; Caltagirone, Carlo; Carlesimo, Giovanni A.

2010-01-01

There is now a large body of evidence suggesting that color and photographic detail exert an effect on recognition of visually presented familiar objects. However, an unresolved issue is whether these factors act at the visual, the semantic or lexical level of the recognition process. In the present study, we investigated this issue by having…

A case-control study on association of proteasome subunit beta 8 (PSMB8) and transporter associated with antigen processing 1 (TAP1) polymorphisms and their transcript levels in vitiligo from Gujarat

PubMed Central

Jadeja, Shahnawaz D.; Mansuri, Mohmmad Shoab; Singh, Mala; Dwivedi, Mitesh; Laddha, Naresh C.

2017-01-01

Background Autoimmunity has been implicated in the destruction of melanocytes from vitiligo skin. Major histocompatibility complex (MHC) class-II linked genes proteasome subunit beta 8 (PSMB8) and transporter associated with antigen processing 1 (TAP1), involved in antigen processing and presentation have been reported to be associated with several autoimmune diseases including vitiligo. Objectives To explore PSMB8 rs2071464 and TAP1 rs1135216 single nucleotide polymorphisms and to estimate the expression of PSMB8 and TAP1 in patients with vitiligo and unaffected controls from Gujarat. Methods PSMB8 rs2071464 polymorphism was genotyped using polymerase chain reaction- restriction fragment length polymorphism (PCR-RFLP) and TAP1 rs1135216 polymorphism was genotyped by amplification refractory mutation system-polymerase chain reaction (ARMS-PCR) in 378 patients with vitiligo and 509 controls. Transcript levels of PSMB8 and TAP1 were measured in the PBMCs of 91 patients and 96 controls by using qPCR. Protein levels of PSMB8 were also determined by Western blot analysis. Results The frequency of ‘TT’ genotype of PSMB8 polymorphism was significantly lowered in patients with generalized and active vitiligo (p = 0.019 and p = 0.005) as compared to controls suggesting its association with the activity of the disease. However, TAP1 polymorphism was not associated with vitiligo susceptibility. A significant decrease in expression of PSMB8 at both transcript level (p = 0.002) as well as protein level (p = 0.0460) was observed in vitiligo patients as compared to controls. No significant difference was observed between patients and controls for TAP1 transcripts (p = 0.553). Interestingly, individuals with the susceptible CC genotype of PSMB8 polymorphism showed significantly reduced PSMB8 transcript level as compared to that of CT and TT genotypes (p = 0.009 and p = 0.003 respectively). Conclusions PSMB8 rs2071464 was associated with generalized and active vitiligo from Gujarat whereas TAP1 rs1135216 showed no association. The down-regulation of PSMB8 in patients with risk genotype ‘CC’ advocates the vital role of PSMB8 in the autoimmune basis of vitiligo. PMID:28700671

Ultrafast pulse lasers jump to macro applications

NASA Astrophysics Data System (ADS)

Griebel, Martin; Lutze, Walter; Scheller, Torsten

2016-03-01

Ultrafast Lasers have been proven for several micro applications, e.g. stent cutting, for many years. Within its development of applications Jenoptik has started to use ultrafast lasers in macro applications in the automotive industry. The JenLas D2.fs-lasers with power output control via AOM is an ideal tool for closed loop controlled material processing. Jenoptik enhanced his well established sensor controlled laser weakening process for airbag covers to a new level. The patented process enables new materials using this kind of technology. One of the most sensitive cover materials is genuine leather. As a natural product it is extremely inhomogeneous and sensitive for any type of thermal load. The combination of femtosecond pulse ablation and closed loop control by multiple sensor array opens the door to a new quality level of defined weakening. Due to the fact, that the beam is directed by scanning equipment the process can be split in multiple cycles additionally reducing the local energy input. The development used the 5W model as well as the latest 10W release of JenLas D2.fs and achieved amazing processing speeds which directly fulfilled the requirements of the automotive industry. Having in mind that the average cycle time of automotive processes is about 60s, trials had been done of processing weakening lines in genuine leather of 1.2mm thickness. Parameters had been about 15 cycles with 300mm/s respectively resulting in an average speed of 20mm/s and a cycle time even below 60s. First samples had already given into functional and aging tests and passed successfully.

Preliminary Investigation of Workload on Intrastate Bus Traffic Controllers

NASA Astrophysics Data System (ADS)

Yen Bin, Teo; Azlis-Sani, Jalil; Nur Annuar Mohd Yunos, Muhammad; Ismail, S. M. Sabri S. M.; Tajedi, Noor Aqilah Ahmad

2016-11-01

The daily routine of bus traffic controller which involves high mental processes would have a direct impact on the level of workload. To date, the level of workload on the bus traffic controllers in Malaysia is relatively unknown. Excessive workload on bus traffic controllers would affect the control and efficiency of the system. This paper served to study the workload on bus traffic controllers and justify the needs to conduct further detailed research on this field. The objectives of this research are to identify the level of workload on the intrastate bus traffic controllers. Based on the results, recommendations will be proposed for improvements and future studies. The level of workload for the bus traffic controllers is quantified using questionnaire adapted from NASA TLX. Interview sessions were conducted for validation of workload. Sixteen respondents were involved and it was found that the average level of workload based on NASA TLX was 6.91. It was found that workload is not affected by gender and marital status. This study also showed that the level of workload and working experience of bus traffic controllers has a strong positive linear relationship. This study would serve as a guidance and reference related to this field. Since this study is a preliminary investigation, further detailed studies could be conducted to obtain a better comprehension regarding the bus traffic controllers.

Development of a Premium Quality Plasma-derived IVIg (IQYMUNE®) Utilizing the Principles of Quality by Design-A Worked-through Case Study.

PubMed

Paolantonacci, Philippe; Appourchaux, Philippe; Claudel, Béatrice; Ollivier, Monique; Dennett, Richard; Siret, Laurent

2018-01-01

Polyvalent human normal immunoglobulins for intravenous use (IVIg), indicated for rare and often severe diseases, are complex plasma-derived protein preparations. A quality by design approach has been used to develop the Laboratoire Français du Fractionnement et des Biotechnologies new-generation IVIg, targeting a high level of purity to generate an enhanced safety profile while maintaining a high level of efficacy. A modular approach of quality by design was implemented consisting of five consecutive steps to cover all the stages from the product design to the final product control strategy.A well-defined target product profile was translated into 27 product quality attributes that formed the basis of the process design. In parallel, a product risk analysis was conducted and identified 19 critical quality attributes among the product quality attributes. Process risk analysis was carried out to establish the links between process parameters and critical quality attributes. Twelve critical steps were identified, and for each of these steps a risk mitigation plan was established.Among the different process risk mitigation exercises, five process robustness studies were conducted at qualified small scale with a design of experiment approach. For each process step, critical process parameters were identified and, for each critical process parameter, proven acceptable ranges were established. The quality risk management and risk mitigation outputs, including verification of proven acceptable ranges, were used to design the process verification exercise at industrial scale.Finally, the control strategy was established using a mix, or hybrid, of the traditional approach plus elements of the quality by design enhanced approach, as illustrated, to more robustly assign material and process controls and in order to securely meet product specifications.The advantages of this quality by design approach were improved process knowledge for industrial design and process validation and a clear justification of the process and product specifications as a basis for control strategy and future comparability exercises. © PDA, Inc. 2018.

Comparative Ecology of H2 Cycling in Organotrophic and Phototrophic Ecosystems

NASA Technical Reports Server (NTRS)

Hoehler, Tori M.; Alperin, Marc J.; Albert, Daniel B.; Bebout, Brad M.; Martens, Christopher S.; DesMarais, David J.; DeVincenzi, Don (Technical Monitor)

2001-01-01

The simple biochemistry of H2 is critical to a large number of microbial processes, affecting the interaction of organisms with each other and with the environment. The sensitivity of these many processes to H2 can be described quantitatively, at a basic thermodynamic level. This shared dependence on H2 may provide a means for interpreting the ecology and system-level biogeochemistry of widely variant microbial ecosystems on a common (and quantitative) level. Understanding the factors that control H2 itself is a critical prerequisite. Here, we examine two ecosystems that vary widely with respect to H2 cycling. In anoxic, 'organotrophic' sediments from Cape Lookout Bight (North Carolina, USA), H2 partial pressures are strictly maintained at low, steady-state levels by H2-consuming organisms, in a fashion that can be quantitatively predicted by simple thermodynamic calculations. In phototrophic microbial mats from Baja, Mexico, H2 partial pressures are instead controlled by the activity of light-sensitive H2-producing organisms. In consequence, H2 partial pressures within the system fluctuate by orders of magnitude on hour-long time scales. The differences in H2 cycling subsequently impact H2-sensitive microbial processes, such as methanogenesis. For example, the presence of sulfate in the organotrophic system always yielded low levels of H2 that were inhibitory to methanogenesis; however, the elevated levels of H2 in the phototrophic system favored methane production at significant levels, even in the presence of high sulfate concentrations. The myriad of other H2-sensitive microbial processes are expected to exhibit similar behavior.

“A manager in the minds of doctors:” a comparison of new modes of control in European hospitals

PubMed Central

2013-01-01

Background Hospital governance increasingly combines management and professional self-governance. This article maps the new emergent modes of control in a comparative perspective and aims to better understand the relationship between medicine and management as hybrid and context-dependent. Theoretically, we critically review approaches into the managerialism-professionalism relationship; methodologically, we expand cross-country comparison towards the meso-level of organisations; and empirically, the focus is on processes and actors in a range of European hospitals. Methods The research is explorative and was carried out as part of the FP7 COST action IS0903 Medicine and Management, Working Group 2. Comprising seven European countries, the focus is on doctors and public hospitals. We use a comparative case study design that primarily draws on expert information and document analysis as well as other secondary sources. Results The findings reveal that managerial control is not simply an external force but increasingly integrated in medical professionalism. These processes of change are relevant in all countries but shaped by organisational settings, and therefore create different patterns of control: (1) ‘integrated’ control with high levels of coordination and coherent patterns for cost and quality controls; (2) ‘partly integrated’ control with diversity of coordination on hospital and department level and between cost and quality controls; and (3) ‘fragmented’ control with limited coordination and gaps between quality control more strongly dominated by medicine, and cost control by management. Conclusions Our comparison highlights how organisations matter and brings the crucial relevance of ‘coordination’ of medicine and management across the levels (hospital/department) and the substance (cost/quality-safety) of control into perspective. Consequently, coordination may serve as a taxonomy of emergent modes of control, thus bringing new directions for cost-efficient and quality-effective hospital governance into perspective. PMID:23819578

Evaluation of particulate matter emissions from manganese alloy production using life-cycle assessment.

PubMed

Davourie, Julia; Westfall, Luke; Ali, Mohammed; McGough, Doreen

2017-01-01

Life-cycle assessments (LCAs) provide a wealth of industry data to assist in evaluating the environmental impacts of industrial processes and product supply chains. In this investigation, data from a recent LCA covering global manganese alloy production was used to evaluate sources of particulate matter (PM) emissions associated with the manganese alloy supply chain. The analysis is aimed at providing an empirical, industry-averaged breakdown of the contribution that processes and emissions controls have on total emissions, manganese releases and occupational exposure. The assessment shows that 66% of PM emissions associated with manganese production occur beyond manganese facilities. Direct or on-site emissions represent 34% of total PM and occur predominantly as disperse sources during mineral extraction and hauling, and as primary furnace emissions. The largest contribution of manganese-bearing PM at ground-level is associated with fugitive emissions from metal and slag tapping, casting, crushing and screening. The evaluation provides a high-level ranking of emissions by process area, to assist in identifying priority areas for industry-wide initiatives to reduce emissions and occupational exposure of manganese. The range of PM emission levels in industry indicate that further enhancements in PM emissions can be achieved by sharing of best practices in emissions controls, limiting furnace conditions which lead to by-passing of emissions controls and application of secondary emission controls to capture fugitive emissions during tapping and casting. The LCA approach to evaluating PM emissions underscores the important role that process optimization and resource efficiency have on reducing PM emissions throughout the manganese supply chain. Copyright © 2016. Published by Elsevier B.V.

TOMM40 rs2075650 May Represent a New Candidate Gene for Vulnerability to Major Depressive Disorder

PubMed Central

McFarquhar, Martyn; Elliott, Rebecca; McKie, Shane; Thomas, Emma; Downey, Darragh; Mekli, Krisztina; Toth, Zoltan G; Anderson, Ian M; Deakin, JF William; Juhasz, Gabriella

2014-01-01

Evidence suggests that depression is a risk factor for dementia; however, the relationship between the two conditions is not fully understood. A novel gene (TOMM40) has been consistently associated with Alzheimer's disease (AD), but has received no attention in depression. We conducted a three-level cross-sectional study to investigate the association of the TOMM40 rs2075650 SNP with depression. We recruited a community sample of 1220 participants (571 controls, 649 lifetime depression) to complete a psychiatric background questionnaire, the Brief Symptom Inventory, and Big Five Inventory at Level-1, 243 (102 controls, 97 remitted, 44 currently depressed) to complete a face-to-face clinical interview and neuropsychological testing at Level-2 and 58 (33 controls, 25 remitted) to complete an emotional face-processing task during fMRI at Level-3. Our results indicated that the TOMM40 rs2075650 G allele was a significant risk factor for lifetime depression (p=0.00006) and, in depressed subjects, was a significant predictor of low extraversion (p=0.009). Currently depressed risk allele carriers showed subtle executive dysfunction (p=0.004) and decreased positive memory bias (p=0.021) together with reduced activity in the posterior (p(FWE)=0.045) and anterior (p(FWE)=0.041) cingulate during sad face emotion processing. Our results suggest that TOMM40 rs2075650 may be a risk factor for the development of depression characterized by reduced extraversion, impaired executive function, and decreased positive emotional recall, and reduced top-down cortical control during sad emotion processing. PMID:24549102

Influence of using challenging tasks in biology classrooms on students' cognitive knowledge structure: an empirical video study

NASA Astrophysics Data System (ADS)

Nawani, Jigna; Rixius, Julia; Neuhaus, Birgit J.

2016-08-01

Empirical analysis of secondary biology classrooms revealed that, on average, 68% of teaching time in Germany revolved around processing tasks. Quality of instruction can thus be assessed by analyzing the quality of tasks used in classroom discourse. This quasi-experimental study analyzed how teachers used tasks in 38 videotaped biology lessons pertaining to the topic 'blood and circulatory system'. Two fundamental characteristics used to analyze tasks include: (1) required cognitive level of processing (e.g. low level information processing: repetiition, summary, define, classify and high level information processing: interpret-analyze data, formulate hypothesis, etc.) and (2) complexity of task content (e.g. if tasks require use of factual, linking or concept level content). Additionally, students' cognitive knowledge structure about the topic 'blood and circulatory system' was measured using student-drawn concept maps (N = 970 students). Finally, linear multilevel models were created with high-level cognitive processing tasks and higher content complexity tasks as class-level predictors and students' prior knowledge, students' interest in biology, and students' interest in biology activities as control covariates. Results showed a positive influence of high-level cognitive processing tasks (β = 0.07; p < .01) on students' cognitive knowledge structure. However, there was no observed effect of higher content complexity tasks on students' cognitive knowledge structure. Presented findings encourage the use of high-level cognitive processing tasks in biology instruction.

Statistical process control methods allow the analysis and improvement of anesthesia care.

PubMed

Fasting, Sigurd; Gisvold, Sven E

2003-10-01

Quality aspects of the anesthetic process are reflected in the rate of intraoperative adverse events. The purpose of this report is to illustrate how the quality of the anesthesia process can be analyzed using statistical process control methods, and exemplify how this analysis can be used for quality improvement. We prospectively recorded anesthesia-related data from all anesthetics for five years. The data included intraoperative adverse events, which were graded into four levels, according to severity. We selected four adverse events, representing important quality and safety aspects, for statistical process control analysis. These were: inadequate regional anesthesia, difficult emergence from general anesthesia, intubation difficulties and drug errors. We analyzed the underlying process using 'p-charts' for statistical process control. In 65,170 anesthetics we recorded adverse events in 18.3%; mostly of lesser severity. Control charts were used to define statistically the predictable normal variation in problem rate, and then used as a basis for analysis of the selected problems with the following results: Inadequate plexus anesthesia: stable process, but unacceptably high failure rate; Difficult emergence: unstable process, because of quality improvement efforts; Intubation difficulties: stable process, rate acceptable; Medication errors: methodology not suited because of low rate of errors. By applying statistical process control methods to the analysis of adverse events, we have exemplified how this allows us to determine if a process is stable, whether an intervention is required, and if quality improvement efforts have the desired effect.

College drinking behaviors: mediational links between parenting styles, impulse control, and alcohol-related outcomes.

PubMed

Patock-Peckham, Julie A; Morgan-Lopez, Antonio A

2006-06-01

Mediational links between parenting styles (authoritative, authoritarian, permissive), impulsiveness (general control), drinking control (specific control), and alcohol use and abuse were tested. A pattern-mixture approach (for modeling non-ignorable missing data) with multiple-group structural equation models with 421 (206 female, 215 male) college students was used. Gender was examined as a potential moderator of parenting styles on control processes related to drinking. Specifically, the parent-child gender match was found to have implications for increased levels of impulsiveness (a significant mediator of parenting effects on drinking control). These findings suggest that a parent with a permissive parenting style who is the same gender as the respondent can directly influence control processes and indirectly influence alcohol use and abuse.

It Takes Three: Selection, Influence, and De-Selection Processes of Depression in Adolescent Friendship Networks

ERIC Educational Resources Information Center

Van Zalk, Maarten Herman Walter; Kerr, Margaret; Branje, Susan J. T.; Stattin, Hakan; Meeus, Wim H. J.

2010-01-01

The authors of this study tested a selection-influence-de-selection model of depression. This model explains friendship influence processes (i.e., friends' depressive symptoms increase adolescents' depressive symptoms) while controlling for two processes: friendship selection (i.e., selection of friends with similar levels of depressive symptoms)…

Logical Access Control Mechanisms in Computer Systems.

ERIC Educational Resources Information Center

Hsiao, David K.

The subject of access control mechanisms in computer systems is concerned with effective means to protect the anonymity of private information on the one hand, and to regulate the access to shareable information on the other hand. Effective means for access control may be considered on three levels: memory, process and logical. This report is a…

[United Plackett-Burman and Box-Behnken design to control formation of indirubin in process of preparing indigo naturalis].

PubMed

Liu, Zeyu; Su, Zhetong; Yang, Ming; Zou, Wenquan

2010-10-01

To screen the factors that affect indirubin-generated significantly in the process of preparing indigo naturalis, optimize level combination and determine the optimum technology for indirubin-generated. Using concentration of indirubin (mg x g(-1)) that generated by fresh leaf as an index, Plackett-Burman design, Box-Behnken design response surface analysis as the statistical method, we screened the significantly influencing factors and the optimal level combination. The soaking and making indirubin process in preparing indigo naturalis was identified as the wax is not removed before immersion with immersion pH 7, solvent volume-leaf weight (mL: g)15, soaked not avoided light, soaking 48 h, temperature 60 degrees C, ventilation time of 180 min, and added ammonia water to adjust pH to 10.5. The soaking and making indirubin process in preparing indigo naturalis is optimized systematically. It clarify the various factors on the impact of the active ingredient indirubin which controlled by industrialized production become reality in the process of preparing indigo naturalis, at the same time, it lay the foundation for processing principle of indigo naturalis.

Cognitive Functions in Elite and Sub-Elite Youth Soccer Players Aged 13 to 17 Years.

PubMed

Huijgen, Barbara C H; Leemhuis, Sander; Kok, Niels M; Verburgh, Lot; Oosterlaan, Jaap; Elferink-Gemser, Marije T; Visscher, Chris

2015-01-01

Soccer players are required to anticipate and react continuously in a changing, relatively unpredictable situation in the field. Cognitive functions might be important to be successful in soccer. The current study investigated the relationship between cognitive functions and performance level in elite and sub-elite youth soccer players aged 13-17 years. A total of 47 elite youth soccer players (mean age 15.5 years, SD = 0.9) and 41 sub-elite youth soccer players (mean age 15.2 years, SD = 1.2) performed tasks for "higher-level" cognitive functions measuring working memory (i.e., Visual Memory Span), inhibitory control (i.e., Stop-Signal Task), cognitive flexibility (i.e., Trail Making Test), and metacognition (i.e., Delis-Kaplan Executive Function System Design Fluency Test). "Lower-level" cognitive processes, i.e., reaction time and visuo-perceptual abilities, were also measured with the previous tasks. ANOVA's showed that elite players outscored sub-elite players at the "higher-level" cognitive tasks only, especially on metacognition (p < .05). Using stepwise discriminant analysis, 62.5% of subjects was correctly assigned to one of the groups based on their metacognition, inhibitory control and cognitive flexibility performance. Controlling for training hours and academic level, MANCOVA's showed differences in favor of the elite youth soccer players on inhibitory control (p = .001), and cognitive flexibility (p = .042), but not on metacognition (p = .27). No differences were found concerning working memory nor the "lower-level" cognitive processes (p > .05). In conclusion, elite youth soccer players have better inhibitory control, cognitive flexibility, and especially metacognition than their sub-elite counterparts. However, when training hours are taken into account, differences between elite and sub-elite youth soccer players remain apparent on inhibitory control and cognitive flexibility in contrast to metacognition. This highlights the need for longitudinal studies to further investigate the importance of "higher-level" cognitive functions for talent identification, talent development and performance in soccer.

Control Design for an Advanced Geared Turbofan Engine

NASA Technical Reports Server (NTRS)

Chapman, Jeffryes W.; Litt, Jonathan S.

2017-01-01

This paper describes the design process for the control system of an advanced geared turbofan engine. This process is applied to a simulation that is representative of a 30,000 pound-force thrust class concept engine with two main spools, ultra-high bypass ratio, and a variable area fan nozzle. Control system requirements constrain the non-linear engine model as it operates throughout its flight envelope of sea level to 40,000 feet and from 0 to 0.8 Mach. The purpose of this paper is to review the engine control design process for an advanced turbofan engine configuration. The control architecture selected for this project was developed from literature and reflects a configuration that utilizes a proportional integral controller with sets of limiters that enable the engine to operate safely throughout its flight envelope. Simulation results show the overall system meets performance requirements without exceeding operational limits.

The Bilingual Language Interaction Network for Comprehension of Speech*

PubMed Central

Marian, Viorica

2013-01-01

During speech comprehension, bilinguals co-activate both of their languages, resulting in cross-linguistic interaction at various levels of processing. This interaction has important consequences for both the structure of the language system and the mechanisms by which the system processes spoken language. Using computational modeling, we can examine how cross-linguistic interaction affects language processing in a controlled, simulated environment. Here we present a connectionist model of bilingual language processing, the Bilingual Language Interaction Network for Comprehension of Speech (BLINCS), wherein interconnected levels of processing are created using dynamic, self-organizing maps. BLINCS can account for a variety of psycholinguistic phenomena, including cross-linguistic interaction at and across multiple levels of processing, cognate facilitation effects, and audio-visual integration during speech comprehension. The model also provides a way to separate two languages without requiring a global language-identification system. We conclude that BLINCS serves as a promising new model of bilingual spoken language comprehension. PMID:24363602

[The main directions of improving the system of state accounting and control of radioactive substances and radioactive waste products].

PubMed

2012-01-01

This paper describes a modification of the basic directions of state accounting and control of radioactive substances and radioactive waste products, whose implementation will significantly improve the efficiency of its operation at the regional level. Selected areas are designed to improve accounting and control system for the submission of the enterprises established by the reporting forms, the quality of the information contained in them, as well as structures of information and process for collecting, analyzing and data processing concerning radioactive substances and waste products.

Incentive-related modulation of cognitive control in healthy, anxious, and depressed adolescents: development and psychopathology related differences.

PubMed

Hardin, Michael G; Schroth, Elizabeth; Pine, Daniel S; Ernst, Monique

2007-05-01

Developmental changes in cognitive and affective processes contribute to adolescent risk-taking behavior, emotional intensification, and psychopathology. The current study examined adolescent development of cognitive control processes and their modulation by incentive, in health and psychopathology. Predictions include 1) better cognitive control in adults than adolescents, and in healthy adolescents than anxious and depressed adolescents, and 2) a stronger influence of incentives in adolescents than adults, and in healthy adolescents than their depressed and anxious counterparts. Antisaccadic eye movement parameters, which provide a measure of cognitive control, were collected during a reward antisaccade task that included parameterized incentive levels. Participants were 20 healthy adults, 30 healthy adolescents, 16 adolescents with an anxiety disorder, and 11 adolescents with major depression. Performance accuracy and saccade latency were analyzed to test both developmental and psychopathology hypotheses. Development and psychopathology group differences in cognitive control were found. Specifically, adults performed better than healthy adolescents, and healthy adolescents than anxious and depressed adolescents. Incentive improved accuracy for all groups; however, incremental increases were not sufficiently large to further modulate performance. Incentives also affected saccade latencies, pushing healthy adolescent latencies to adult levels, while being less effective in adolescents with depression or anxiety. This latter effect was partially mediated by anxiety symptom severity. Current findings evidence the modulation of cognitive control processes by incentives. While seen in both healthy adults and healthy adolescents, this modulatory effect was stronger in youth. While anxious and depressed adolescents exhibited improved cognitive control under incentives, this effect was smaller than that in healthy adolescents. These findings suggest differential incentive and/or cognitive control processing in anxiety and depression, and across development. Differences could result from disorder specific, or combined developmental and pathological mechanisms.

Incentive-related modulation of cognitive control in healthy, anxious, and depressed adolescents

PubMed Central

Hardin, Michael G.; Schroth, Elizabeth; Pine, Daniel S.; Ernst, Monique

2009-01-01

Background Developmental changes in cognitive and affective processes contribute to adolescent risk-taking behavior, emotional intensification, and psychopathology. The current study examined adolescent development of cognitive control processes and their modulation by incentive, in health and psychopathology. Predictions include 1) better cognitive control in adults than adolescents, and in healthy adolescents than anxious and depressed adolescents, and 2) a stronger influence of incentives in adolescents than adults, and in healthy adolescents than their depressed and anxious counterparts. Methods Antisaccadic eye movement parameters, which provide a measure of cognitive control, were collected during a reward antisaccade task that included parameterized incentive levels. Participants were 20 healthy adults, 30 healthy adolescents, 16 adolescents with an anxiety disorder, and 11 adolescents with major depression. Performance accuracy and saccade latency were analyzed to test both developmental and psychopathology hypotheses. Results Development and psychopathology group differences in cognitive control were found. Specifically, adults performed better than healthy adolescents, and healthy adolescents than anxious and depressed adolescents. Incentive improved accuracy for all groups; however, incremental increases were not sufficiently large to further modulate performance. Incentives also affected saccade latencies, pushing healthy adolescent latencies to adult levels, while being less effective in adolescents with depression or anxiety. This latter effect was partially mediated by anxiety symptom severity. Conclusions Current findings evidence the modulation of cognitive control processes by incentives. While seen in both healthy adults and healthy adolescents, this modulatory effect was stronger in youth. While anxious and depressed adolescents exhibited improved cognitive control under incentives, this effect was smaller than that in healthy adolescents. These findings suggest differential incentive and/or cognitive control processing in anxiety and depression, and across development. Differences could result from disorder specific, or combined developmental and pathological mechanisms. PMID:17501725

Monitoring and control of the biogas process based on propionate concentration using online VFA measurement.

PubMed

Boe, Kanokwan; Steyer, Jean-Philippe; Angelidaki, Irini

2008-01-01

Simple logic control algorithms were tested for automatic control of a lab-scale CSTR manure digester. Using an online VFA monitoring system, propionate concentration in the reactor was used as parameter for control of the biogas process. The propionate concentration was kept below a threshold of 10 mM by manipulating the feed flow. Other online parameters such as pH, biogas production, total VFA, and other individual VFA were also measured to examine process performance. The experimental results showed that a simple logic control can successfully prevent the reactor from overload, but with fluctuations of the propionate level due to the nature of control approach. The fluctuation of propionate concentration could be reduced, by adding a lower feed flow limit into the control algorithm to prevent undershooting of propionate response. It was found that use of the biogas production as a main control parameter, rather than propionate can give a more stable process, since propionate was very persistent and only responded very slowly to the decrease of the feed flow which lead to high fluctuation of biogas production. Propionate, however, was still an excellent parameter to indicate process stress under gradual overload and thus recommended as an alarm in the control algorithm. Copyright IWA Publishing 2008.

The Hazard Analysis and Critical Control Points (HACCP) generic model for the production of Thai fermented pork sausage (Nham).

PubMed

Paukatong, K V; Kunawasen, S

2001-01-01

Nham is a traditional Thai fermented pork sausage. The major ingredients of Nham are ground pork meat and shredded pork rind. Nham has been reported to be contaminated with Salmonella spp., Staphylococcus aureus, and Listeria monocytogenes. Therefore, it is a potential cause of foodborne diseases for consumers. A Hazard Analysis and Critical Control Points (HACCP) generic model has been developed for the Nham process. Nham processing plants were observed and a generic flow diagram of Nham processes was constructed. Hazard analysis was then conducted. Other than microbial hazards, the pathogens previously found in Nham, sodium nitrite and metal were identified as chemical and physical hazards in this product, respectively. Four steps in the Nham process have been identified as critical control points. These steps are the weighing of the nitrite compound, stuffing, fermentation, and labeling. The chemical hazard of nitrite must be controlled during the weighing step. The critical limit of nitrite levels in the Nham mixture has been set at 100-200 ppm. This level is high enough to control Clostridium botulinum but does not cause chemical hazards to the consumer. The physical hazard from metal clips could be prevented by visual inspection of every Nham product during stuffing. The microbiological hazard in Nham could be reduced in the fermentation process. The critical limit of the pH of Nham was set at lower than 4.6. Since this product is not cooked during processing, finally, educating the consumer, by providing information on the label such as "safe if cooked before consumption", could be an alternative way to prevent the microbiological hazards of this product.

Programmable architecture for pixel level processing tasks in lightweight strapdown IR seekers

NASA Astrophysics Data System (ADS)

Coates, James L.

1993-06-01

Typical processing tasks associated with missile IR seeker applications are described, and a straw man suite of algorithms is presented. A fully programmable multiprocessor architecture is realized on a multimedia video processor (MVP) developed by Texas Instruments. The MVP combines the elements of RISC, floating point, advanced DSPs, graphics processors, display and acquisition control, RAM, and external memory. Front end pixel level tasks typical of missile interceptor applications, operating on 256 x 256 sensor imagery, can be processed at frame rates exceeding 100 Hz in a single MVP chip.

Addressing Production System Failures Using Multi-agent Control

NASA Astrophysics Data System (ADS)

Gautam, Rajesh; Miyashita, Kazuo

Output in high-volume production facilities is limited by bottleneck machines. We propose a control mechanism by modeling workstations as agents that pull jobs from other agents based on their current WIP level and requirements. During failures, when flows of some jobs are disrupted, the agents pull alternative jobs to maintain utilization of their capacity at a high level. In this paper, we empirically demonstrate that the proposed mechanism can react to failures more appropriately than other control mechanisms using a benchmark problem of a semiconductor manufacturing process.

Space Power Management and Distribution Status and Trends

NASA Technical Reports Server (NTRS)

Reppucci, G. M.; Biess, J. J.; Inouye, L.

1984-01-01

An overview of space power management and distribution (PMAD) is provided which encompasses historical and current technology trends. The PMAD components discussed include power source control, energy storage control, and load power processing electronic equipment. The status of distribution equipment comprised of rotary joints and power switchgear is evaluated based on power level trends in the public, military, and commercial sectors. Component level technology thrusts, as driven by perceived system level trends, are compared to technology status of piece-parts such as power semiconductors, capacitors, and magnetics to determine critical barriers.

Implicit and explicit attitudes predict smoking cessation: moderating effects of experienced failure to control smoking and plans to quit.

PubMed

Chassin, Laurie; Presson, Clark C; Sherman, Steven J; Seo, Dong-Chul; Macy, Jonathan T

2010-12-01

The current study tested implicit and explicit attitudes as prospective predictors of smoking cessation in a Midwestern community sample of smokers. Results showed that the effects of attitudes significantly varied with levels of experienced failure to control smoking and plans to quit. Explicit attitudes significantly predicted later cessation among those with low (but not high or average) levels of experienced failure to control smoking. Conversely, however, implicit attitudes significantly predicted later cessation among those with high levels of experienced failure to control smoking, but only if they had a plan to quit. Because smoking cessation involves both controlled and automatic processes, interventions may need to consider attitude change interventions that focus on both implicit and explicit attitudes. (PsycINFO Database Record (c) 2010 APA, all rights reserved).

Behavioral and Emotional Regulation and Adolescent Substance Use Problems: A Test of Moderation Effects in a Dual-Process Model

PubMed Central

Wills, Thomas A.; Pokhrel, Pallav; Morehouse, Ellen; Fenster, Bonnie

2011-01-01

In a structural model, we tested how relations of predictors to level of adolescent substance use (tobacco, alcohol, marijuana), and to substance-related impaired-control and behavior problems, are moderated by good self-control and poor regulation in behavioral and emotional domains. The participants were a sample of 1,116 public high-school students. In a multiple-group analysis for good self-control, the paths from negative life events to substance use level and from level to behavior problems were lower among persons scoring higher on good behavioral self-control. In a multiple-group analysis for poor regulation, the paths from negative life events to level and from peer substance use to level were greater among persons scoring higher on poor behavioral (but not emotional) regulation; an inverse path from academic competence to level was greater among persons scoring higher on both aspects of poor regulation. Paths from level to impaired-control and behavior problems were greater among persons scoring higher on both poor behavioral and poor emotional regulation. Theoretical implications for the basis of moderation effects are discussed. PMID:21443302

Effects of task and age on the magnitude and structure of force fluctuations: insights into underlying neuro-behavioral processes.

PubMed

Vieluf, Solveig; Temprado, Jean-Jacques; Berton, Eric; Jirsa, Viktor K; Sleimen-Malkoun, Rita

2015-03-13

The present study aimed at characterizing the effects of increasing (relative) force level and aging on isometric force control. To achieve this objective and to infer changes in the underlying control mechanisms, measures of information transmission, as well as magnitude and time-frequency structure of behavioral variability were applied to force-time-series. Older adults were found to be weaker, more variable, and less efficient than young participants. As a function of force level, efficiency followed an inverted-U shape in both groups, suggesting a similar organization of the force control system. The time-frequency structure of force output fluctuations was only significantly affected by task conditions. Specifically, a narrower spectral distribution with more long-range correlations and an inverted-U pattern of complexity changes were observed with increasing force level. Although not significant older participants displayed on average a less complex behavior for low and intermediate force levels. The changes in force signal's regularity presented a strong dependence on time-scales, which significantly interacted with age and condition. An inverted-U profile was only observed for the time-scale relevant to the sensorimotor control process. However, in both groups the peak was not aligned with the optimum of efficiency. Our results support the view that behavioral variability, in terms of magnitude and structure, has a functional meaning and affords non-invasive markers of the adaptations of the sensorimotor control system to various constraints. The measures of efficiency and variability ought to be considered as complementary since they convey specific information on the organization of control processes. The reported weak age effect on variability and complexity measures suggests that the behavioral expression of the loss of complexity hypothesis is not as straightforward as conventionally admitted. However, group differences did not completely vanish, which suggests that age differences can be more or less apparent depending on task properties and whether difficulty is scaled in relative or absolute terms.

Experimental comparison of conventional and nonlinear model-based control of a mixing tank

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haeggblom, K.E.

1993-11-01

In this case study concerning control of a laboratory-scale mixing tank, conventional multiloop single-input single-output (SISO) control is compared with model-based'' control where the nonlinearity and multivariable characteristics of the process are explicitly taken into account. It is shown, especially if the operating range of the process is large, that the two outputs (level and temperature) cannot be adequately controlled by multiloop SISO control even if gain scheduling is used. By nonlinear multiple-input multiple-output (MIMO) control, on the other hand, very good control performance is obtained. The basic approach to nonlinear control used in this study is first to transformmore » the process into a globally linear and decoupled system, and then to design controllers for this system. Because of the properties of the resulting MIMO system, the controller design is very easy. Two nonlinear control system designs based on a steady-state and a dynamic model, respectively, are considered. In the dynamic case, both setpoint tracking and disturbance rejection can be addressed separately.« less

Design of experiments enhanced statistical process control for wind tunnel check standard testing

NASA Astrophysics Data System (ADS)

Phillips, Ben D.

The current wind tunnel check standard testing program at NASA Langley Research Center is focused on increasing data quality, uncertainty quantification and overall control and improvement of wind tunnel measurement processes. The statistical process control (SPC) methodology employed in the check standard testing program allows for the tracking of variations in measurements over time as well as an overall assessment of facility health. While the SPC approach can and does provide researchers with valuable information, it has certain limitations in the areas of process improvement and uncertainty quantification. It is thought by utilizing design of experiments methodology in conjunction with the current SPC practices that one can efficiently and more robustly characterize uncertainties and develop enhanced process improvement procedures. In this research, methodologies were developed to generate regression models for wind tunnel calibration coefficients, balance force coefficients and wind tunnel flow angularities. The coefficients of these regression models were then tracked in statistical process control charts, giving a higher level of understanding of the processes. The methodology outlined is sufficiently generic such that this research can be applicable to any wind tunnel check standard testing program.

Risk Perception of HIV/AIDS and Low Self-Control Trait: Explaining Preventative Behaviors Among Iranian University Students

PubMed Central

Esmaeilzadeh, Safooreh; Allahverdipour, Hamid; Fathi, Behrouz; Shirzadi, Shayesteh

2016-01-01

Background: In spite of developed countries there are progressive trend about HIV/AIDS and its’ aspects of transmission in the low socio-economic societies. The aim of this was to explain the youth's behavior in adopting HIV/AIDS related preventive behaviors in a sample of Iranian university students by emphasizing on fear appeals approaches alongside examining the role of self-control trait for explaining adoption on danger or fear control processes based on Extended Parallel Process Model (EPPM). Methods: A sample of 156 randomly selected university students in Jolfa, Iran was recruited in a predictive cross-sectional study by application of a researcher-designed questionnaire through self-report data collection manner. Sexual high risk behaviors, the EPPM variables, self-control trait, and general self-efficacy were measured as theoretical framework. Results: Findings indicated that 31.3% of participants were in the fear control process versus 68.7% in danger control about HIV/AIDS and also the presence of multi-sex partners and amphetamine consumption amongst the participants. Low self-control trait and low perceived susceptibility significantly were related to having a history of multi-sex partners while high level of self-efficacy significantly increased the probability of condom use. Conclusion: Findings of the study were indicative of the protective role of high level of self-control, perceived susceptibility and self-efficacy factors on youth's high-risk behaviors and their preventative skills as well. PMID:26573026

Collaboration processes and perceived effectiveness of integrated care projects in primary care: a longitudinal mixed-methods study.

PubMed

Valentijn, Pim P; Ruwaard, Dirk; Vrijhoef, Hubertus J M; de Bont, Antoinette; Arends, Rosa Y; Bruijnzeels, Marc A

2015-10-09

Collaborative partnerships are considered an essential strategy for integrating local disjointed health and social services. Currently, little evidence is available on how integrated care arrangements between professionals and organisations are achieved through the evolution of collaboration processes over time. The first aim was to develop a typology of integrated care projects (ICPs) based on the final degree of integration as perceived by multiple stakeholders. The second aim was to study how types of integration differ in changes of collaboration processes over time and final perceived effectiveness. A longitudinal mixed-methods study design based on two data sources (surveys and interviews) was used to identify the perceived degree of integration and patterns in collaboration among 42 ICPs in primary care in The Netherlands. We used cluster analysis to identify distinct subgroups of ICPs based on the final perceived degree of integration from a professional, organisational and system perspective. With the use of ANOVAs, the subgroups were contrasted based on: 1) changes in collaboration processes over time (shared ambition, interests and mutual gains, relationship dynamics, organisational dynamics and process management) and 2) final perceived effectiveness (i.e. rated success) at the professional, organisational and system levels. The ICPs were classified into three subgroups with: 'United Integration Perspectives (UIP)', 'Disunited Integration Perspectives (DIP)' and 'Professional-oriented Integration Perspectives (PIP)'. ICPs within the UIP subgroup made the strongest increase in trust-based (mutual gains and relationship dynamics) as well as control-based (organisational dynamics and process management) collaboration processes and had the highest overall effectiveness rates. On the other hand, ICPs with the DIP subgroup decreased on collaboration processes and had the lowest overall effectiveness rates. ICPs within the PIP subgroup increased in control-based collaboration processes (organisational dynamics and process management) and had the highest effectiveness rates at the professional level. The differences across the three subgroups in terms of the development of collaboration processes and the final perceived effectiveness provide evidence that united stakeholders' perspectives are achieved through a constructive collaboration process over time. Disunited perspectives at the professional, organisation and system levels can be aligned by both trust-based and control-based collaboration processes.

The development of a contract quality assurance program within the Virginia Department of Highways.

DOT National Transportation Integrated Search

1989-01-01

In order to assure the quality of construction products and processes, the Virginia Department of Transportation has established three levels of construction control. First, contractors themselves provide oversight and quality control as set out in t...

Food safety and nutritional quality for the prevention of non communicable diseases: the Nutrient, hazard Analysis and Critical Control Point process (NACCP).

PubMed

Di Renzo, Laura; Colica, Carmen; Carraro, Alberto; Cenci Goga, Beniamino; Marsella, Luigi Tonino; Botta, Roberto; Colombo, Maria Laura; Gratteri, Santo; Chang, Ting Fa Margherita; Droli, Maurizio; Sarlo, Francesca; De Lorenzo, Antonino

2015-04-23

The important role of food and nutrition in public health is being increasingly recognized as crucial for its potential impact on health-related quality of life and the economy, both at the societal and individual levels. The prevalence of non-communicable diseases calls for a reformulation of our view of food. The Hazard Analysis and Critical Control Point (HACCP) system, first implemented in the EU with the Directive 43/93/CEE, later replaced by Regulation CE 178/2002 and Regulation CE 852/2004, is the internationally agreed approach for food safety control. Our aim is to develop a new procedure for the assessment of the Nutrient, hazard Analysis and Critical Control Point (NACCP) process, for total quality management (TMQ), and optimize nutritional levels. NACCP was based on four general principles: i) guarantee of health maintenance; ii) evaluate and assure the nutritional quality of food and TMQ; iii) give correct information to the consumers; iv) ensure an ethical profit. There are three stages for the application of the NACCP process: 1) application of NACCP for quality principles; 2) application of NACCP for health principals; 3) implementation of the NACCP process. The actions are: 1) identification of nutritional markers, which must remain intact throughout the food supply chain; 2) identification of critical control points which must monitored in order to minimize the likelihood of a reduction in quality; 3) establishment of critical limits to maintain adequate levels of nutrient; 4) establishment, and implementation of effective monitoring procedures of critical control points; 5) establishment of corrective actions; 6) identification of metabolic biomarkers; 7) evaluation of the effects of food intake, through the application of specific clinical trials; 8) establishment of procedures for consumer information; 9) implementation of the Health claim Regulation EU 1924/2006; 10) starting a training program. We calculate the risk assessment as follows: Risk (R) = probability (P) × damage (D). The NACCP process considers the entire food supply chain "from farm to consumer"; in each point of the chain it is necessary implement a tight monitoring in order to guarantee optimal nutritional quality.

[Endocrine-metabolic peculiarities in women of reproductive age with hyperplastic processes of cervix and mammary glands].

PubMed

Kadzhaia, N R; Virsaladze, D K; Tkeshelashvili, B D; Dzhavashvili, L V; Dzhugeli, M K

2006-05-01

The aim of our investigation was the detection of endocrine-metabolic disorders in patients with hyperplastic processes of endomyometrium, uterine cervix and mammary glands. 88 patients of reproductive age with several gynaecological complaints have been investigated. 72 patients with hyperplastic processes in endomyometrium, uterine cervix (hyperplasia, polyposis, myoma) and mammary glands (fibroadenomatosis, adenomatosis) were selected in main group. Control group consisted of 16 patients without any hyperplastic processes of reproductive organs. Metabolic syndrome in main group was revealed in 28% of cases, in control - 18,8% (chi(2)=3,95, p=0,047); insulin resistance - 37,5% and 18,7% (chi(2)=4,59, p=0,033), respectively; obesity - 52,8% and 25,0% (chi(2)=4,05, p=0,045), respectively; dyslipidemia - 52,8% and 0,0%; hypertension - 26,4% and 12,5% (chi(2)=1,88, p=NS), respectively. Blood leptin level in main group was - 13,7+/-10,9 ng/ml, and in control - 5,0+/-2,9 ng/ml (p=0,005). Our results suggest that metabolic syndrome and its components significantly influences the formation of hyperplastic processes of endomyometrium, uterine cervix and mammary glands. Blood leptin level is significantly increased in patients with hyperplastic pathologies.

Outlining face processing skills of portrait artists: Perceptual experience with faces predicts performance.

PubMed

Devue, Christel; Barsics, Catherine

2016-10-01

Most humans seem to demonstrate astonishingly high levels of skill in face processing if one considers the sophisticated level of fine-tuned discrimination that face recognition requires. However, numerous studies now indicate that the ability to process faces is not as fundamental as once thought and that performance can range from despairingly poor to extraordinarily high across people. Here we studied people who are super specialists of faces, namely portrait artists, to examine how their specific visual experience with faces relates to a range of face processing skills (perceptual discrimination, short- and longer term recognition). Artists show better perceptual discrimination and, to some extent, recognition of newly learned faces than controls. They are also more accurate on other perceptual tasks (i.e., involving non-face stimuli or mental rotation). By contrast, artists do not display an advantage compared to controls on longer term face recognition (i.e., famous faces) nor on person recognition from other sensorial modalities (i.e., voices). Finally, the face inversion effect exists in artists and controls and is not modulated by artistic practice. Advantages in face processing for artists thus seem to closely mirror perceptual and visual short term memory skills involved in portraiture. Copyright © 2016 Elsevier Ltd. All rights reserved.

Self-focused processing after severe traumatic brain injury: Relationship to neurocognitive functioning and mood symptoms.

PubMed

Ownsworth, Tamara; Gooding, Kynan; Beadle, Elizabeth

2018-05-28

To investigate the impact of neurocognitive functioning on the self-focused processing styles of rumination and reflection, and the relationship to mood symptoms after severe traumatic brain injury (TBI). A cross-sectional design with a between-group component comparing self-focused processing styles and mood symptoms of adults with TBI and age- and gender-matched controls. Fifty-two participants with severe TBI (75% male, M age = 36.56, SD = 12.39) completed cognitive tests of attention, memory, executive functioning and the Awareness Questionnaire, Reflection and Rumination Questionnaire (RRQ), and Depression, Anxiety, and Stress Scales (DASS - 21). Fifty age- and gender-matched controls completed the RRQ and DASS-21. TBI participants reported significantly greater mood symptoms than controls (p < .05); however, levels of rumination and reflection did not significantly differ. TBI participants high on both reflection and rumination had significantly greater mood symptoms than those with high reflection and low rumination (p < .001). Higher levels of rumination and reflection were associated with better working memory and immediate and delayed verbal memory (r = .36-.43, p < .01). Higher levels of rumination were also associated with greater verbal fluency, self-awareness, and mood symptoms (r = .36-.70, p < .01). Individuals with better memory functioning may be more likely to engage in self-focused processing after severe TBI. Reflection without ruminative tendencies is more adaptive for mental health than reflection with rumination. Individuals with severe TBI report more mood symptoms than non-injured controls but do not differ on self-focused processing. Poorer memory function is related to lower levels of rumination and reflection. Reflection without ruminative tendencies is adaptive for mental health after severe TBI. Individuals with greater self-awareness and ruminative tendencies are at increased risk of mental health problems following severe TBI. Rumination and reflection were assessed using a self-report measure which assumes that people with severe TBI are able to reliably report on self-focused processing styles. The direction of associations between self-focused processing, self-awareness, and mood symptoms could not be determined due to the cross-sectional design. © 2018 The British Psychological Society.

The Relationship between Vitamin D and Coronary Artery Ectasia in Subjects with a Normal C-Reactive Protein Level

PubMed Central

Cagirci, Goksel; Yuksel, Isa Oner; Bayar, Nermin; Koklu, Erkan; Guven, Ramazan; Arslan, Sakir

2017-01-01

Background and Objectives Vitamin D is generally known to be closely related to inflammation. The effects of vitamin D on coronary artery disease (CAD) are not fully explained. Nowadays, coronary artery ectasia (CAE) cases are common and are regarded as being a kind of CAD. We aimed to investigate, in a case-control study, the relationship between vitamin D and CAE without an associated inflammatory process. Subjects and Methods This study population included 201 patients (CAE group, 121 males; mean age, 61.2±6.4 years) with isolated CAE; and 197 healthy individuals (control group, 119 males; mean age, 62.4±5.8 years), comprising the control group, who had normal coronary arteries. These participants concurrently underwent routine biochemical tests, tests for inflammatory markers, and tests for 25-OH vitamin D in whole-blood draws. These parameters were compared. Results There are no statistical significance differences among the groups for basic clinical characteristics (p>0.05). Inflammatory markers were recorded and compared to exclude any inflammatory process. All of them were similar, and no statistical significance difference was found. The average parathyroid hormone (PTH) level of patients was higher than the average PTH level in controls (41.8±15.1 pg/mL vs. 19.1±5.81 pg/mL; p<0.001). Also, the average 25-OH vitamin D level of patients was lower than the average 25-OH vitamin D level of controls (14.5±6.3 ng/mL vs. 24.6±9.3 ng/mL; p<0.001). In receiver operating characteristic curve analysis, the observed cut-off value for vitamin D between the control group and patients was 10.8 and 85.6% sensitivity and 75.2% specificity (area under the curve: 0.854, 95% confidence interval: 0.678-0.863). Conclusion We found that there is an association between vitamin D and CAE in patients who had no inflammatory processes. Our study may provide evidence for the role of vitamin D as a non-inflammatory factor in the pathophysiology of CAE. PMID:28382079

On the Application of Different Event-Based Sampling Strategies to the Control of a Simple Industrial Process

PubMed Central

Sánchez, José; Guarnes, Miguel Ángel; Dormido, Sebastián

2009-01-01

This paper is an experimental study of the utilization of different event-based strategies for the automatic control of a simple but very representative industrial process: the level control of a tank. In an event-based control approach it is the triggering of a specific event, and not the time, that instructs the sensor to send the current state of the process to the controller, and the controller to compute a new control action and send it to the actuator. In the document, five control strategies based on different event-based sampling techniques are described, compared, and contrasted with a classical time-based control approach and a hybrid one. The common denominator in the time, the hybrid, and the event-based control approaches is the controller: a proportional-integral algorithm with adaptations depending on the selected control approach. To compare and contrast each one of the hybrid and the pure event-based control algorithms with the time-based counterpart, the two tasks that a control strategy must achieve (set-point following and disturbance rejection) are independently analyzed. The experimental study provides new proof concerning the ability of event-based control strategies to minimize the data exchange among the control agents (sensors, controllers, actuators) when an error-free control of the process is not a hard requirement. PMID:22399975

The COGs (context, object, and goals) in multisensory processing.

PubMed

ten Oever, Sanne; Romei, Vincenzo; van Atteveldt, Nienke; Soto-Faraco, Salvador; Murray, Micah M; Matusz, Pawel J

2016-05-01

Our understanding of how perception operates in real-world environments has been substantially advanced by studying both multisensory processes and "top-down" control processes influencing sensory processing via activity from higher-order brain areas, such as attention, memory, and expectations. As the two topics have been traditionally studied separately, the mechanisms orchestrating real-world multisensory processing remain unclear. Past work has revealed that the observer's goals gate the influence of many multisensory processes on brain and behavioural responses, whereas some other multisensory processes might occur independently of these goals. Consequently, other forms of top-down control beyond goal dependence are necessary to explain the full range of multisensory effects currently reported at the brain and the cognitive level. These forms of control include sensitivity to stimulus context as well as the detection of matches (or lack thereof) between a multisensory stimulus and categorical attributes of naturalistic objects (e.g. tools, animals). In this review we discuss and integrate the existing findings that demonstrate the importance of such goal-, object- and context-based top-down control over multisensory processing. We then put forward a few principles emerging from this literature review with respect to the mechanisms underlying multisensory processing and discuss their possible broader implications.

Use telecommunications for real-time process control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zilberman, I.; Bigman, J.; Sela, I.

1996-05-01

Process operators design real-time accurate information to monitor and control product streams and to optimize unit operations. The challenge is how to cost-effectively install sophisticated analytical equipment in harsh environments such as process areas and maintain system reliability. Incorporating telecommunications technology with near infrared (NIR) spectroscopy may be the bridge to help operations achieve their online control goals. Coupling communications fiber optics with NIR analyzers enables the probe and sampling system to remain in the field and crucial analytical equipment to be remotely located in a general purpose area without specialized protection provisions. The case histories show how two refineriesmore » used NIR spectroscopy online to track octane levels for reformate streams.« less

Integrating metabolic modeling and population heterogeneity analysis into optimizing recombinant protein production by Komagataella (Pichia) pastoris.

PubMed

Theron, Chrispian W; Berrios, Julio; Delvigne, Frank; Fickers, Patrick

2018-01-01

The methylotrophic yeast Komagataella (Pichia) pastoris has become one of the most utilized cell factories for the production of recombinant proteins over the last three decades. This success story is linked to its specific physiological traits, i.e., the ability to grow at high cell density in inexpensive culture medium and to secrete proteins at high yield. Exploiting methanol metabolism is at the core of most P. pastoris-based processes but comes with its own challenges. Co-feeding cultures with glycerol/sorbitol and methanol is a promising approach, which can benefit from improved understanding and prediction of metabolic response. The development of profitable processes relies on the construction and selection of efficient producing strains from less efficient ones but also depends on the ability to master the bioreactor process itself. More specifically, how a bioreactor processes could be monitored and controlled to obtain high yield of production. In this review, new perspectives are detailed regarding a multi-faceted approach to recombinant protein production processes by P. pastoris; including gaining improved understanding of the metabolic pathways involved, accounting for variations in transcriptional and translational efficiency at the single cell level and efficient monitoring and control of methanol levels at the bioreactor level.

A survey on the design of multiprocessing systems for artificial intelligence applications

NASA Technical Reports Server (NTRS)

Wah, Benjamin W.; Li, Guo Jie

1989-01-01

Some issues in designing computers for artificial intelligence (AI) processing are discussed. These issues are divided into three levels: the representation level, the control level, and the processor level. The representation level deals with the knowledge and methods used to solve the problem and the means to represent it. The control level is concerned with the detection of dependencies and parallelism in the algorithmic and program representations of the problem, and with the synchronization and sheduling of concurrent tasks. The processor level addresses the hardware and architectural components needed to evaluate the algorithmic and program representations. Solutions for the problems of each level are illustrated by a number of representative systems. Design decisions in existing projects on AI computers are classed into top-down, bottom-up, and middle-out approaches.

Control of chemical dynamics by lasers: theoretical considerations.

PubMed

Kondorskiy, Alexey; Nanbu, Shinkoh; Teranishi, Yoshiaki; Nakamura, Hiroki

2010-06-03

Theoretical ideas are proposed for laser control of chemical dynamics. There are the following three elementary processes in chemical dynamics: (i) motion of the wave packet on a single adiabatic potential energy surface, (ii) excitation/de-excitation or pump/dump of wave packet, and (iii) nonadiabatic transitions at conical intersections of potential energy surfaces. A variety of chemical dynamics can be controlled, if we can control these three elementary processes as we desire. For (i) we have formulated the semiclassical guided optimal control theory, which can be applied to multidimensional real systems. The quadratic or periodic frequency chirping method can achieve process (ii) with high efficiency close to 100%. Concerning process (iii) mentioned above, the directed momentum method, in which a predetermined momentum vector is given to the initial wave packet, makes it possible to enhance the desired transitions at conical intersections. In addition to these three processes, the intriguing phenomenon of complete reflection in the nonadiabatic-tunneling-type of potential curve crossing can also be used to control a certain class of chemical dynamics. The basic ideas and theoretical formulations are provided for the above-mentioned processes. To demonstrate the effectiveness of these controlling methods, numerical examples are shown by taking the following processes: (a) vibrational photoisomerization of HCN, (b) selective and complete excitation of the fine structure levels of K and Cs atoms, (c) photoconversion of cyclohexadiene to hexatriene, and (d) photodissociation of OHCl to O + HCl.

Prospective memory and intraindividual variability in ongoing task response times in an adult lifespan sample: the role of cue focality.

PubMed

Ihle, Andreas; Ghisletta, Paolo; Kliegel, Matthias

2017-03-01

To contribute to the ongoing conceptual debate of what traditional mean-level ongoing task (OT) costs tell us about the attentional processes underlying prospective memory (PM), we investigated costs to intraindividual variability (IIV) in OT response times as a potentially sensitive indicator of attentional processes. Particularly, we tested whether IIV in OT responses may reflect controlled employment of attentional processes versus lapses of controlled attention, whether these processes differ across adulthood, and whether it is moderated by cue focality. We assessed 150 individuals (19-82 years) in a focal and a nonfocal PM condition. In addition, external measures of inhibition and working memory were assessed. In line with the predictions of the lapses-of-attention/inefficient-executive-control account, our data support the view that costs to IIV in OT trials of PM tasks reflect fluctuations in the efficiency of executive functioning, which was related to failures in prospective remembering, particularly in nonfocal PM tasks, potentially due to their increased executive demands. The additional value of considering costs to IIV over and beyond traditional mean-level OT costs in PM research is discussed.

Barriers to adopting and implementing local-level tobacco control policies.

PubMed

Satterlund, Travis D; Cassady, Diana; Treiber, Jeanette; Lemp, Cathy

2011-08-01

Although California communities have been relatively successful in adopting and implementing a wide range of local tobacco control policies, the process has not been without its setbacks and barriers. Little is known about local policy adoption, and this paper examines these processes related to adopting and implementing outdoor smoke-free policies, focusing on the major barriers faced by local-level tobacco control organizations in this process. Ninety-six projects funded by the California Tobacco Control Program submitted final evaluation reports pertaining to an outdoor smoking objective, and the reports from these projects were analyzed. The barriers were grouped in three primary areas: politically polarizing barriers, organizational barriers, and local political orientation. The barriers identified in this study underscore the need for an organized action plan in adopting local tobacco policy. The authors also suggest potential strategies to offset the barriers, including: (1) having a "champion" who helps to carry an objective forward; (2) tapping into a pool of youth volunteers; (3) collecting and using local data as a persuasive tool; (4) educating the community in smoke-free policy efforts; (5) working strategically within the local political climate; and (6) demonstrating to policymakers the constituent support for proposed policy.

Counterfactual cognitive deficit in persons with Parkinson's disease

PubMed Central

McNamara, P; Durso, R; Brown, A; Lynch, A

2003-01-01

Background: Counterfactuals are mental representations of alternatives to past events. Recent research has shown them to be important for other cognitive processes, such as planning, causal reasoning, problem solving, and decision making—all processes independently linked to the frontal lobes. Objective: To test the hypothesis that counterfactual thinking is impaired in some patients with Parkinson's disease and is linked to frontal dysfunction in these patients. Methods. Measures of counterfactual processing and frontal lobe functioning were administered to 24 persons with Parkinson's disease and 15 age matched healthy controls. Results. Patients with Parkinson's disease spontaneously generated significantly fewer counterfactuals than controls despite showing no differences from controls on a semantic fluency test; they also performed at chance levels on a counterfactual inference test, while age matched controls performed above chance levels on this test. Performance on both the counterfactual generation and inference tests correlated significantly with performance on two tests traditionally linked to frontal lobe functioning (Stroop colour–word interference and Tower of London planning tasks) and one test of pragmatic social communication skills. Conclusions: Counterfactual thinking is impaired in Parkinson's disease. This impairment may be related to frontal lobe dysfunction. PMID:12876235

External Contamination Control of Attached Payloads on the International Space Station

NASA Technical Reports Server (NTRS)

Soares, Carlos E.; Mikatarian, Ronald R.; Olsen, Randy L.; Huang, Alvin Y.; Steagall, Courtney A.; Schmidl, William D.; Wright, Bruce D.; Koontz, Steven

2012-01-01

The International Space Station (ISS) is an on-orbit platform for science utilization in low Earth orbit with multiple sites for external payloads with exposure to the natural and induced environments. Contamination is one of the induced environments that can impact performance, mission success and science utilization on the vehicle. This paper describes the external contamination control requirements and integration process for externally mounted payloads on the ISS. The external contamination control requirements are summarized and a description of the integration and verification process is detailed to guide payload developers in the certification process of attached payloads on the vehicle. A description of the required data certification deliverables covers the characterization of contamination sources. Such characterization includes identification, usage and operational data for each class of contamination source. Classes of external contamination sources covered are vacuum exposed materials, sources of leakage, vacuum venting and thrusters. ISS system level analyses are conducted by the ISS Space Environments Team to certify compliance with external contamination control requirements. This paper also addresses the ISS induced contamination environment at attached payload sites, both at the requirements level as well as measurements made on ISS.

Humidity control of an incubator using the microcontroller-based active humidifier system employing an ultrasonic nebulizer.

PubMed

Güler, I; Burunkaya, M

2002-01-01

Relative humidity levels of an incubator were measured and controlled. An ultrasonic nebulizer system as an active humidifier was used to humidify the incubator environment. An integrated circuit-type humidity sensor was used to measure the humidity level of the incubator environment. Measurement and control processes were achieved by a PIC microcontroller. The high-performance and high-speed PIC provided the flexibility of the system. The developed system can be used effectively for the intensive care of newborns and/or premature babies. Since the humidifier generates an aerosol in ambient conditions, it is possible to provide the high relative humidity level for therapeutic and diagnostic purposes in medicine.

Dying scenarios improve recall as much as survival scenarios.

PubMed

Burns, Daniel J; Hart, Joshua; Kramer, Melanie E

2014-01-01

Merely contemplating one's death improves retention for entirely unrelated material learned subsequently. This "dying to remember" effect seems conceptually related to the survival processing effect, whereby processing items for their relevance to being stranded in the grasslands leads to recall superior to that of other deep processing control conditions. The present experiments directly compared survival processing scenarios with "death processing" scenarios. Results showed that when the survival and dying scenarios are closely matched on key dimensions, and possible congruency effects are controlled, the dying and survival scenarios produced equivalently high recall levels. We conclude that the available evidence (cf. Bell, Roer, & Buchner, 2013; Klein, 2012), while not definitive, is consistent with the possibility of overlapping mechanisms.

Two Aspects of Activation: Arousal and Subjective Significance – Behavioral and Event-Related Potential Correlates Investigated by Means of a Modified Emotional Stroop Task

PubMed Central

Imbir, Kamil; Spustek, Tomasz; Bernatowicz, Gabriela; Duda, Joanna; Żygierewicz, Jarosław

2017-01-01

The arousal level of words presented in a Stroop task was found to affect their interference on the required naming of the words’ color. Based on a dual-processes approach, we propose that there are two aspects to activation: arousal and subjective significance. Arousal is crucial for automatic processing. Subjective significance is specific to controlled processing. Based on this conceptual model, we predicted that arousal would enhance interference in a Stroop task, as attention would be allocated to the meaning of the inhibited word. High subjective significance should have the opposite effect, i.e., it should enhance the controlled and explicit part of Stroop task processing, which is color naming. We found that response latencies were modulated by the interaction between the arousal and subjective significance levels of words. The longest reaction times were observed for highly arousing words of medium subjective significance level. Arousal shaped event related potentials in the 150–290 ms time range, while effects of subjective significance were found for 50–150, 150–290, and 290–530 ms time ranges. PMID:29311872

The effect of nerve section on the incidence and distribution of gap junctions in the odontoblast layer of the cat.

PubMed

Holland, G R

1987-08-01

Gap junctions are numerous in the odontoblast layer of the dental pulp and may link sensory axons to odontoblasts. If these junctions do link axons and odontoblasts, they, together with the axons, should disappear after cutting the pulpal nerves centrally. Under general anesthesia the inferior alveolar nerve on one side of two young adult cats was sectioned. Under general anesthesia the animals were perfused with fixative 56 hours later and the coronal dental pulp prepared for electron microscopy. Ultrathin sections were examined from the level of the pulpal cornu and levels approximately one, two, and three mm below this. The incidence of cell processes and gap junctions was measured at different distances from the pulp predentin junction, and operated and control sides compared. The odontoblast layer at the level of the cornu differed from elsewhere in having, on the control side, a greater density of cell processes and gap junctions and in having clearly recognizable axons approaching to within 5 to 10 micron of the predentin. The only statistically significant changes after nerve section occurred in this layer and consisted of a decline in the incidence of cell processes and of gap junctions that link one cell process to another. There was no significant difference between the operated and control sides in the number of gap junctions linking cell processes to recognizable cell bodies. The odontoblast layer in the pulpal cornu contained substantial numbers of unsheathed axons, many presumably en route to the dentin. These axons may participate in gap junctions that link them to other cell processes, possibly even other axons.(ABSTRACT TRUNCATED AT 250 WORDS)

Adaptive, fast walking in a biped robot under neuronal control and learning.

PubMed

Manoonpong, Poramate; Geng, Tao; Kulvicius, Tomas; Porr, Bernd; Wörgötter, Florentin

2007-07-01

Human walking is a dynamic, partly self-stabilizing process relying on the interaction of the biomechanical design with its neuronal control. The coordination of this process is a very difficult problem, and it has been suggested that it involves a hierarchy of levels, where the lower ones, e.g., interactions between muscles and the spinal cord, are largely autonomous, and where higher level control (e.g., cortical) arises only pointwise, as needed. This requires an architecture of several nested, sensori-motor loops where the walking process provides feedback signals to the walker's sensory systems, which can be used to coordinate its movements. To complicate the situation, at a maximal walking speed of more than four leg-lengths per second, the cycle period available to coordinate all these loops is rather short. In this study we present a planar biped robot, which uses the design principle of nested loops to combine the self-stabilizing properties of its biomechanical design with several levels of neuronal control. Specifically, we show how to adapt control by including online learning mechanisms based on simulated synaptic plasticity. This robot can walk with a high speed (>3.0 leg length/s), self-adapting to minor disturbances, and reacting in a robust way to abruptly induced gait changes. At the same time, it can learn walking on different terrains, requiring only few learning experiences. This study shows that the tight coupling of physical with neuronal control, guided by sensory feedback from the walking pattern itself, combined with synaptic learning may be a way forward to better understand and solve coordination problems in other complex motor tasks.

Maintenance of CO2 level in a BLSS by controlling solid waste treatment unit

NASA Astrophysics Data System (ADS)

Dong, Yingying; Li, Leyuan; Liu, Hong; Fu, Yuming; Xie, Beizhen; Hu, Dawei; Liu, Dianlei; Dong, Chen; Liu, Guanghui

A bioregenerative life support system (BLSS) is an artificial closed ecosystem for providing basic human life support for long-duration, far-distance space explorations such as lunar bases. In such a system, the circulation of gases is one of the main factor for realizing a higher closure degree. O2 produced by higher plants goes to humans, as well as microorganisms for the treatment of inedible plant biomass and human wastes; CO2 produced by the crew and microorganisms is provided for plant growth. During this process, an excessively high CO2 level will depress plant growth and may be harmful to human health; and if the CO2 level is too low, plant growth will also be affected. Thus, keeping the balance between CO2 and O2 levels is a crucial problem. In this study, a high-efficiency, controllable solid waste treatment unit is constructed, which adopts microbial fermentation of the mixture of inedible biomass and human wastes. CO2 production during the fermentation process is controlled by adjusting fermentation temperature, aeration rate, moisture, etc., so as to meet the CO2 requirement of plants

What has fMRI told us about the Development of Cognitive Control through Adolescence?

PubMed Central

Luna, Beatriz; Padmanabhan, Aarthi; O’Hearn, Kirsten

2009-01-01

Cognitive control, the ability to voluntarily guide our behavior, continues to improve throughout adolescence. Below we review the literature on age-related changes in brain function related to response inhibition and working memory, which support cognitive control. Findings from studies using functional magnetic imaging (fMRI) indicate that processing errors, sustaining a cognitive control state, and reaching adult levels of precision, persist through adolescence. Developmental changes in patterns of brain function suggest that core regions of the circuitry underlying cognitive control are on-line early in development. However, age-related changes in localized processes across the brain and in establishing long range connections that support top-down modulation of behavior may support more effective neural processing for optimal mature executive function. While great progress has been made in understanding the age-related changes in brain processes underlying cognitive development, there are still important challenges in developmental neuroimaging methods and the interpretation of data that need to be addressed. PMID:19765880

Top-down causation by information control: from a philosophical problem to a scientific research programme

PubMed Central

Auletta, G; Ellis, G.F.R; Jaeger, L

2008-01-01

It has been claimed that different types of causes must be considered in biological systems, including top-down as well as same-level and bottom-up causation, thus enabling the top levels to be causally efficacious in their own right. To clarify this issue, the important distinctions between information and signs are introduced here and the concepts of information control and functional equivalence classes in those systems are rigorously defined and used to characterize when top-down causation by feedback control happens, in a way that is testable. The causally significant elements we consider are equivalence classes of lower level processes, realized in biological systems through different operations having the same outcome within the context of information control and networks. PMID:18319208

Effect of cloacal plugging on microbial recovery from partially processed broilers.

PubMed

Musgrove, M T; Cason, J A; Fletcher, D L; Stern, N J; Cox, N A; Bailey, J S

1997-03-01

Experiments were performed to test the contribution of bacteria contained in the intestinal tract of broilers at the beginning of processing to counts on the exterior of modified New York-dressed carcasses. Thirty-two birds were processed for each of seven replications. Within each replication, batches of four birds were electrocuted, scalded, and picked, with batches alternating between treatment and control groups. Treated birds were cloacally plugged with rayon fiber tampons prior to electrocution to prevent escape of intestinal contents during scalding and picking. Control birds were processed in the same manner, except that cloacal plugs were inserted immediately after defeathering to reduce escape of intestinal contents during sampling. Gram-negative enteric bacteria and Campylobacter spp. were enumerated on carcasses by whole carcass rinse procedure and in cecal contents. Counts were converted to log10 and subjected to analysis of variance. Cecal levels of Gram-negative enterics were significantly higher for plugged birds, but there was not a significant difference between levels of cecal Campylobacter spp. between treatment groups. Plugging before electrocution resulted in significantly lower levels (2.5 vs 3.0 log10 cfu/mL) of Campylobacter spp. and Gram-negative enteric bacteria (3.0 vs 3.4 log10 cfu/mL) in carcass rinses of treatment birds than in those of controls. All carcasses were positive for Gram-negative enterics. Cloacal plugging resulted in significantly lower incidence of Campylobacter spp. carcass contamination as determined by chi-square. Intestinal carriage of both campylobacters and Gram-negative enteric bacteria appears to influence the microbial quality of the carcass during processing.

Through tobacco industry eyes: civil society and the FCTC process from Philip Morris and British American Tobacco’s perspectives

PubMed Central

Gonzalez, Mariaelena; Green, Lawrence W; Glantz, Stanton A

2011-01-01

Objective To analyse the models Philip Morris (PM) and British American Tobacco (BAT) used internally to understand tobacco control non-governmental organizations (NGOs) and their relationship to the global tobacco control policy-making process that resulted in the Framework Convention for Tobacco Control (FCTC). Methods Analysis of internal tobacco industry documents in the Legacy Tobacco Document Library. Results PM contracted with Mongoven, Biscoe, and Duchin, Inc. (MBD, a consulting firm specialising in NGO surveillance) as advisors. MBD argued that because NGOs are increasingly linked to epistemic communities, NGOs could insert themselves into the global policy-making process and influence the discourse surrounding the treaty-making process. MBD advised PM to insert itself into the policy-making process, mimicking NGO behaviour. BAT’s Consumer and Regulatory Affairs (CORA) department argued that global regulation emerged from the perception (by NGOs and governments) that the industry could not regulate itself, leading to BAT advocating social alignment and self-regulation to minimise the impact of the FCTC. Most efforts to block or redirect the FCTC failed. Conclusions PM and BAT articulated a global policy-making environment in which NGOs are key, non-state stakeholders, and as a result, internationalised some of their previous national-level strategies. After both companies failed to prevent the FCTC, their strategies began to align. Multinational corporations have continued to successfully employ some of the strategies outlined in this paper at the local and national level while being formally excluded from ongoing FCTC negotiations at the global level. PMID:21636611

Injection Process Control of the Well at the Hydrodynamic Research of Coalbed

NASA Astrophysics Data System (ADS)

Odnokopylov, I. G.; Galtseva, O. V.; Krasnov, I. Yu; Smirnov, A. O.; Karpov, M. S.; Surzhikova, O. A.; Kuznetsov, V. V.; Li, J.

2017-04-01

This scientific work is devoted to the study results of water injection process into the well at the hydrodynamic research by using the high pressure unregulated pump. The injection process should be accompanied by the retention of some hydraulic parameters at constant level during some time. Various variants for use of mechatronic nodes for automatization of water injection process are considered. Scheme for reducing the load on the pump and equipment in hydraulic system and also for improving the quality control system with high accuracy is shown. Simulation results of injection process into the well at the pressure and consumption fixation and recommendations for the use of the proposed schemes depending on the technological process are given.

Knowledge elicitation for an operator assistant system in process control tasks

NASA Technical Reports Server (NTRS)

Boy, Guy A.

1988-01-01

A knowledge based system (KBS) methodology designed to study human machine interactions and levels of autonomy in allocation of process control tasks is presented. Users are provided with operation manuals to assist them in normal and abnormal situations. Unfortunately, operation manuals usually represent only the functioning logic of the system to be controlled. The user logic is often totally different. A method is focused on which illicits user logic to refine a KBS shell called an Operator Assistant (OA). If the OA is to help the user, it is necessary to know what level of autonomy gives the optimal performance of the overall man-machine system. For example, for diagnoses that must be carried out carefully by both the user and the OA, interactions are frequent, and processing is mostly sequential. Other diagnoses can be automated, in which the case the OA must be able to explain its reasoning in an appropriate level of detail. OA structure was used to design a working KBS called HORSES (Human Orbital Refueling System Expert System). Protocol analysis of pilots interacting with this system reveals that the a-priori analytical knowledge becomes more structured with training and the situation patterns more complex and dynamic. This approach can improve the a-priori understanding of human and automatic reasoning.

Neuroscientific Model of Motivational Process

PubMed Central

Kim, Sung-il

2013-01-01

Considering the neuroscientific findings on reward, learning, value, decision-making, and cognitive control, motivation can be parsed into three sub processes, a process of generating motivation, a process of maintaining motivation, and a process of regulating motivation. I propose a tentative neuroscientific model of motivational processes which consists of three distinct but continuous sub processes, namely reward-driven approach, value-based decision-making, and goal-directed control. Reward-driven approach is the process in which motivation is generated by reward anticipation and selective approach behaviors toward reward. This process recruits the ventral striatum (reward area) in which basic stimulus-action association is formed, and is classified as an automatic motivation to which relatively less attention is assigned. By contrast, value-based decision-making is the process of evaluating various outcomes of actions, learning through positive prediction error, and calculating the value continuously. The striatum and the orbitofrontal cortex (valuation area) play crucial roles in sustaining motivation. Lastly, the goal-directed control is the process of regulating motivation through cognitive control to achieve goals. This consciously controlled motivation is associated with higher-level cognitive functions such as planning, retaining the goal, monitoring the performance, and regulating action. The anterior cingulate cortex (attention area) and the dorsolateral prefrontal cortex (cognitive control area) are the main neural circuits related to regulation of motivation. These three sub processes interact with each other by sending reward prediction error signals through dopaminergic pathway from the striatum and to the prefrontal cortex. The neuroscientific model of motivational process suggests several educational implications with regard to the generation, maintenance, and regulation of motivation to learn in the learning environment. PMID:23459598

Neuroscientific model of motivational process.

PubMed

Kim, Sung-Il

2013-01-01

Considering the neuroscientific findings on reward, learning, value, decision-making, and cognitive control, motivation can be parsed into three sub processes, a process of generating motivation, a process of maintaining motivation, and a process of regulating motivation. I propose a tentative neuroscientific model of motivational processes which consists of three distinct but continuous sub processes, namely reward-driven approach, value-based decision-making, and goal-directed control. Reward-driven approach is the process in which motivation is generated by reward anticipation and selective approach behaviors toward reward. This process recruits the ventral striatum (reward area) in which basic stimulus-action association is formed, and is classified as an automatic motivation to which relatively less attention is assigned. By contrast, value-based decision-making is the process of evaluating various outcomes of actions, learning through positive prediction error, and calculating the value continuously. The striatum and the orbitofrontal cortex (valuation area) play crucial roles in sustaining motivation. Lastly, the goal-directed control is the process of regulating motivation through cognitive control to achieve goals. This consciously controlled motivation is associated with higher-level cognitive functions such as planning, retaining the goal, monitoring the performance, and regulating action. The anterior cingulate cortex (attention area) and the dorsolateral prefrontal cortex (cognitive control area) are the main neural circuits related to regulation of motivation. These three sub processes interact with each other by sending reward prediction error signals through dopaminergic pathway from the striatum and to the prefrontal cortex. The neuroscientific model of motivational process suggests several educational implications with regard to the generation, maintenance, and regulation of motivation to learn in the learning environment.

Automated gas chromatography

DOEpatents

Mowry, C.D.; Blair, D.S.; Rodacy, P.J.; Reber, S.D.

1999-07-13

An apparatus and process for the continuous, near real-time monitoring of low-level concentrations of organic compounds in a liquid, and, more particularly, a water stream. A small liquid volume of flow from a liquid process stream containing organic compounds is diverted by an automated process to a heated vaporization capillary where the liquid volume is vaporized to a gas that flows to an automated gas chromatograph separation column to chromatographically separate the organic compounds. Organic compounds are detected and the information transmitted to a control system for use in process control. Concentrations of organic compounds less than one part per million are detected in less than one minute. 7 figs.

Automated gas chromatography

DOEpatents

Mowry, Curtis D.; Blair, Dianna S.; Rodacy, Philip J.; Reber, Stephen D.

1999-01-01

An apparatus and process for the continuous, near real-time monitoring of low-level concentrations of organic compounds in a liquid, and, more particularly, a water stream. A small liquid volume of flow from a liquid process stream containing organic compounds is diverted by an automated process to a heated vaporization capillary where the liquid volume is vaporized to a gas that flows to an automated gas chromatograph separation column to chromatographically separate the organic compounds. Organic compounds are detected and the information transmitted to a control system for use in process control. Concentrations of organic compounds less than one part per million are detected in less than one minute.

The relationship between mood state and perceived control in contingency learning: effects of individualist and collectivist values

PubMed Central

Msetfi, Rachel M.; Kornbrot, Diana E.; Matute, Helena; Murphy, Robin A.

2015-01-01

Perceived control in contingency learning is linked to psychological wellbeing with low levels of perceived control thought to be a cause or consequence of depression and high levels of control considered to be the hallmark of mental healthiness. However, it is not clear whether this is a universal phenomenon or whether the value that people ascribe to control influences these relationships. Here we hypothesize that values affect learning about control contingencies and influence the relationship between perceived control and symptoms of mood disorders. We tested these hypotheses with European university samples who were categorized as endorsing (or not) values relevant to control—individualist and collectivist values. Three online experimental contingency learning studies (N1 = 127, N2 = 324, N3 = 272) were carried out. Evidence suggested that individualist values influenced basic learning processes via an effect on learning about the context in which events took place. Participants who endorsed individualist values made control judgments that were more in line with an elemental associative learning model, whilst those who were ambivalent about individualist values made judgments that were more consistent with a configural process. High levels of perceived control and individualist values were directly associated with increased euphoric symptoms of bipolar disorder, and such values completely mediated the relation between perceived control and symptoms. The effect of low perceived control on depression was moderated by collectivist values. Anxiety created by dissonance between values and task may be a catalyst for developing mood symptoms. Conclusions are that values play a significant intermediary role in the relation between perceived control and symptoms of mood disturbance. PMID:26483707

Effects of early focal brain injury on memory for visuospatial patterns: selective deficits of global-local processing.

PubMed

Stiles, Joan; Stern, Catherine; Appelbaum, Mark; Nass, Ruth; Trauner, Doris; Hesselink, John

2008-01-01

Selective deficits in visuospatial processing are present early in development among children with perinatal focal brain lesions (PL). Children with right hemisphere PL (RPL) are impaired in configural processing, while children with left hemisphere PL (LPL) are impaired in featural processing. Deficits associated with LPL are less pervasive than those observed with RPL, but this difference may reflect the structure of the tasks used for assessment. Many of the tasks used to date may place greater demands on configural processing, thus highlighting this deficit in the RPL group. This study employed a task designed to place comparable demands on configural and featural processing, providing the opportunity to obtain within-task evidence of differential deficit. Sixty-two 5- to 14-year-old children (19 RPL, 19 LPL, and 24 matched controls) reproduced from memory a series of hierarchical forms (large forms composed of small forms). Global- and local-level reproduction accuracy was scored. Controls were equally accurate on global- and local-level reproduction. Children with RPL were selectively impaired on global accuracy, and children with LPL on local accuracy, thus documenting a double dissociation in global-local processing.

Autoplan: A self-processing network model for an extended blocks world planning environment

NASA Technical Reports Server (NTRS)

Dautrechy, C. Lynne; Reggia, James A.; Mcfadden, Frank

1990-01-01

Self-processing network models (neural/connectionist models, marker passing/message passing networks, etc.) are currently undergoing intense investigation for a variety of information processing applications. These models are potentially very powerful in that they support a large amount of explicit parallel processing, and they cleanly integrate high level and low level information processing. However they are currently limited by a lack of understanding of how to apply them effectively in many application areas. The formulation of self-processing network methods for dynamic, reactive planning is studied. The long-term goal is to formulate robust, computationally effective information processing methods for the distributed control of semiautonomous exploration systems, e.g., the Mars Rover. The current research effort is focusing on hierarchical plan generation, execution and revision through local operations in an extended blocks world environment. This scenario involves many challenging features that would be encountered in a real planning and control environment: multiple simultaneous goals, parallel as well as sequential action execution, action sequencing determined not only by goals and their interactions but also by limited resources (e.g., three tasks, two acting agents), need to interpret unanticipated events and react appropriately through replanning, etc.

Sustainable improvement of animal health care by systematic quality risk management according to the HACCP concept.

PubMed

Noordhuizen, J P; Welpelo, H J

1996-12-01

This paper addresses the principles of the Hazard Analysis Critical Control Point (HACCP) concept as applied to animal health management strategy. Characteristics of the concept were analysed and compared with those of current animal health care strategies for disease risk identification and herd health management, insurance, and certification. HACCP is a hybrid strategy of quality control at both production process and product level. Animal health is considered a particular quality feature. We show that process control (expressed in terms of controlling both general and specific disease risk factors) and product control (expressed in terms of testing animals or animal products for specific disease agents) could form the basis for improving animal health. We conclude that HACCP provides ample opportunity for preventive health action and risk management at a relatively low cost in terms of labour, finance and documentation expenditure, at both the farm and sector level. Epidemiological field studies are currently needed to identify critical control points and to design HACCP procedures for livestock producers. In the long run, HACCP based animal health care can be further developed into a quality control systems approach to cover all aspects that are related, either directly or indirectly, to animal health.

Learning to selectively attend from context-specific attentional histories: A demonstration and some constraints.

PubMed

Crump, Matthew J C

2016-03-01

Multiple lines of evidence from the attention and performance literature show that attention filtering can be controlled by higher level voluntary processes and lower-level cue-driven processes (for recent reviews see Bugg, 2012; Bugg & Crump, 2012; Egner, 2008). The experiments were designed to test a general hypothesis that cue-driven control learns from context-specific histories of prior acts of selective attention. Several web-based flanker studies were conducted via Amazon Mechanical Turk. Attention filtering demands were induced by a secondary one-back memory task after each trial prompting recall of the last target or distractor letter. Blocking recall demands produced larger flanker effects for the distractor than target recall conditions. Mixing recall demands and associating them with particular stimulus-cues (location, colour, letter, and font) sometimes showed rapid, contextual control of flanker interference, and sometimes did not. The results show that subtle methodological parameters can influence whether or not contextual control is observed. More generally, the results show that contextual control phenomena can be influenced by other sources of control, including other cue-driven sources competing for control. (c) 2016 APA, all rights reserved).

Finger tapping and pre-attentive sensorimotor timing in adults with ADHD.

PubMed

Hove, Michael J; Gravel, Nickolas; Spencer, Rebecca M C; Valera, Eve M

2017-12-01

Sensorimotor timing deficits are considered central to attention-deficit/hyperactivity disorder (ADHD). However, the tasks establishing timing impairments often involve interconnected processes, including low-level sensorimotor timing and higher level executive processes such as attention. Thus, the source of timing deficits in ADHD remains unclear. Low-level sensorimotor timing can be isolated from higher level processes in a finger-tapping task that examines the motor response to unexpected shifts of metronome onsets. In this study, adults with ADHD and ADHD-like symptoms (n = 25) and controls (n = 26) performed two finger-tapping tasks. The first assessed tapping variability in a standard tapping task (metronome-paced and unpaced). In the other task, participants tapped along with a metronome that contained unexpected shifts (±15, 50 ms); the timing adjustment on the tap following the shift captures pre-attentive sensorimotor timing (i.e., phase correction) and thus should be free of potential higher order confounds (e.g., attention). In the standard tapping task, as expected, the ADHD group had higher timing variability in both paced and unpaced tappings. However, in the pre-attentive task, performance did not differ between the ADHD and control groups. Together, results suggest that low-level sensorimotor timing and phase correction are largely preserved in ADHD and that some timing impairments observed in ADHD may stem from higher level factors (such as sustained attention).

A Taguchi approach on optimal process control parameters for HDPE pipe extrusion process

NASA Astrophysics Data System (ADS)

Sharma, G. V. S. S.; Rao, R. Umamaheswara; Rao, P. Srinivasa

2017-06-01

High-density polyethylene (HDPE) pipes find versatile applicability for transportation of water, sewage and slurry from one place to another. Hence, these pipes undergo tremendous pressure by the fluid carried. The present work entails the optimization of the withstanding pressure of the HDPE pipes using Taguchi technique. The traditional heuristic methodology stresses on a trial and error approach and relies heavily upon the accumulated experience of the process engineers for determining the optimal process control parameters. This results in setting up of less-than-optimal values. Hence, there arouse a necessity to determine optimal process control parameters for the pipe extrusion process, which can ensure robust pipe quality and process reliability. In the proposed optimization strategy, the design of experiments (DoE) are conducted wherein different control parameter combinations are analyzed by considering multiple setting levels of each control parameter. The concept of signal-to-noise ratio ( S/ N ratio) is applied and ultimately optimum values of process control parameters are obtained as: pushing zone temperature of 166 °C, Dimmer speed at 08 rpm, and Die head temperature to be 192 °C. Confirmation experimental run is also conducted to verify the analysis and research result and values proved to be in synchronization with the main experimental findings and the withstanding pressure showed a significant improvement from 0.60 to 1.004 Mpa.

Using AI Planning Techniques to Automatically Generate Image Processing Procedures: A Preliminary Report

NASA Technical Reports Server (NTRS)

Chien, S.

1994-01-01

This paper describes work on the Multimission VICAR Planner (MVP) system to automatically construct executable image processing procedures for custom image processing requests for the JPL Multimission Image Processing Lab (MIPL). This paper focuses on two issues. First, large search spaces caused by complex plans required the use of hand encoded control information. In order to address this in a manner similar to that used by human experts, MVP uses a decomposition-based planner to implement hierarchical/skeletal planning at the higher level and then uses a classical operator based planner to solve subproblems in contexts defined by the high-level decomposition.

Time course of cognitive recovery after propofol anaesthesia: a level of processing approach.

PubMed

N'Kaoua, Bernard; Véron, Anne-Lise H; Lespinet, Véronique C; Claverie, Bernard; Sztark, François

2002-09-01

The aim of this study was to investigate the time course of recovery of verbal memory after general anaesthesia, as a function of the level (shallow or deep) of processing induced at the time of encoding. Thirty-one patients anaesthetized with propofol and alfentanil were compared with 28 control patients receiving only alfentanil. Memory functions were assessed the day before and 1, 6 and 24 hr after operation. Results show that for the anaesthetized group, shallow processing was impaired for 6 hr after surgery whereas the deeper processing was not recovered even at 24 hr. In addition, no specific effect of age was found.

Controlling and policing substance use(rs).

PubMed

White, Tony

2002-01-01

Controlling drug use--a dynamic, global, politicalized process--is reviewed in terms of selected types of drugs, "natural levels" of drug demand and use, drug markets and the drug market environment, types of traffickers, illicit drug trade profits, approaches to drug control ("War on Drugs", "Zero Tolerance" programs and policies, "normalizing" and legalizing selected drugs), including UN's then relatively recent "Balanced Approach" and facets of drug law enforcement (drug prices and purity levels and values of drug seizures), including various rarely noted benefits to intervention programs and control agents. Unresolved issues and needed "tools" are noted while considering the implications of the first UN's World Drug Report data.

Effects of instructed emotion regulation on valence, arousal, and attentional measures of affective processing.

PubMed

Bernat, Edward M; Cadwallader, Meredith; Seo, Dongju; Vizueta, Nathalie; Patrick, Christopher J

2011-01-01

Cognitive control of emotion has been investigated using tasks prompting participants to increase or decrease emotional responding to affective pictures. This study provides a more comprehensive evaluation of responding in this task by including: pleasant and unpleasant pictures, increase and decrease instructions, additional physiological measures, and a fully randomized design. Findings suggest that control efforts did modulate higher-level affective responses indexed by self-reported valence and expressive facial muscles, but not lower-level affective responses indexed by startle blink and heart rate. Similarly, electrocortical measures evidenced expectable affective responses and control-related activity, but no modulation of affective patterns due to the control efforts.

Automation in the Space Station module power management and distribution Breadboard

NASA Technical Reports Server (NTRS)

Walls, Bryan; Lollar, Louis F.

1990-01-01

The Space Station Module Power Management and Distribution (SSM/PMAD) Breadboard, located at NASA's Marshall Space Flight Center (MSFC) in Huntsville, Alabama, models the power distribution within a Space Station Freedom Habitation or Laboratory module. Originally designed for 20 kHz ac power, the system is now being converted to high voltage dc power with power levels on a par with those expected for a space station module. In addition to the power distribution hardware, the system includes computer control through a hierarchy of processes. The lowest level process consists of fast, simple (from a computing standpoint) switchgear, capable of quickly safing the system. The next level consists of local load center processors called Lowest Level Processors (LLP's). These LLP's execute load scheduling, perform redundant switching, and shed loads which use more than scheduled power. The level above the LLP's contains a Communication and Algorithmic Controller (CAC) which coordinates communications with the highest level. Finally, at this highest level, three cooperating Artificial Intelligence (AI) systems manage load prioritization, load scheduling, load shedding, and fault recovery and management. The system provides an excellent venue for developing and examining advanced automation techniques. The current system and the plans for its future are examined.

Fragile Spectral and Temporal Auditory Processing in Adolescents with Autism Spectrum Disorder and Early Language Delay

ERIC Educational Resources Information Center

Boets, Bart; Verhoeven, Judith; Wouters, Jan; Steyaert, Jean

2015-01-01

We investigated low-level auditory spectral and temporal processing in adolescents with autism spectrum disorder (ASD) and early language delay compared to matched typically developing controls. Auditory measures were designed to target right versus left auditory cortex processing (i.e. frequency discrimination and slow amplitude modulation (AM)…

Population-level compensation impedes biological control of an invasive forb and indirect release of a native grass

Treesearch

Yvette K. Ortega; Dean E. Pearson; Lauren P. Waller; Nancy J. Sturdevant; John L. Maron

2012-01-01

The intentional introduction of specialist insect herbivores for biological control of exotic weeds provides ideal but understudied systems for evaluating important ecological concepts related to top-down control, plant compensatory responses, indirect effects, and the influence of environmental context on these processes. Centaurea stoebe (spotted knapweed) is a...

Multi-interface Level Sensors and New Development in Monitoring and Control of Oil Separators

PubMed Central

Bukhari, Syed Faisal Ahmed; Yang, Wuqiang

2006-01-01

In the oil industry, huge saving may be made if suitable multi-interface level measurement systems are employed for effectively monitoring crude oil separators and efficient control of their operation. A number of techniques, e.g. externally mounted displacers, differential pressure transmitters and capacitance rod devices, have been developed to measure the separation process with gas, oil, water and other components. Because of the unavailability of suitable multi-interface level measurement systems, oil separators are currently operated by the trial-and-error approach. In this paper some conventional techniques, which have been used for level measurement in industry, and new development are discussed.

Identifying strengths and weaknesses of Quality Management Unit University of Sumatera Utara software using SCAMPI C

NASA Astrophysics Data System (ADS)

Gunawan, D.; Amalia, A.; Rahmat, R. F.; Muchtar, M. A.; Siregar, I.

2018-02-01

Identification of software maturity level is a technique to determine the quality of the software. By identifying the software maturity level, the weaknesses of the software can be observed. As a result, the recommendations might be a reference for future software maintenance and development. This paper discusses the software Capability Level (CL) with case studies on Quality Management Unit (Unit Manajemen Mutu) University of Sumatera Utara (UMM-USU). This research utilized Standard CMMI Appraisal Method for Process Improvement class C (SCAMPI C) model with continuous representation. This model focuses on activities for developing quality products and services. The observation is done in three process areas, such as Project Planning (PP), Project Monitoring and Control (PMC), and Requirements Management (REQM). According to the measurement of software capability level for UMM-USU software, turns out that the capability level for the observed process area is in the range of CL1 and CL2. Planning Project (PP) is the only process area which reaches capability level 2, meanwhile, PMC and REQM are still in CL 1 or in performed level. This research reveals several weaknesses of existing UMM-USU software. Therefore, this study proposes several recommendations for UMM-USU to improve capability level for observed process areas.

An object-oriented software approach for a distributed human tracking motion system

NASA Astrophysics Data System (ADS)

Micucci, Daniela L.

2003-06-01

Tracking is a composite job involving the co-operation of autonomous activities which exploit a complex information model and rely on a distributed architecture. Both information and activities must be classified and related in several dimensions: abstraction levels (what is modelled and how information is processed); topology (where the modelled entities are); time (when entities exist); strategy (why something happens); responsibilities (who is in charge of processing the information). A proper Object-Oriented analysis and design approach leads to a modular architecture where information about conceptual entities is modelled at each abstraction level via classes and intra-level associations, whereas inter-level associations between classes model the abstraction process. Both information and computation are partitioned according to level-specific topological models. They are also placed in a temporal framework modelled by suitable abstractions. Domain-specific strategies control the execution of the computations. Computational components perform both intra-level processing and intra-level information conversion. The paper overviews the phases of the analysis and design process, presents major concepts at each abstraction level, and shows how the resulting design turns into a modular, flexible and adaptive architecture. Finally, the paper sketches how the conceptual architecture can be deployed into a concrete distribute architecture by relying on an experimental framework.

Effect of HEH[EHP] impurities on the ALSEP solvent extraction process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holfeltz, Vanessa E.; Campbell, Emily L.; Peterman, Dean R.

In solvent extraction processes, organic phase impurities can negatively impact separation factors, hydrolytic performance, and overall system robustness. This affects the process-level viability of a separation concept and necessitates knowledge of the behavior and mechanisms to control impurities in the solvent. The most widespread way through which impurities are introduced into a system is through impure extractants and/or diluents used to prepare the solvent, and often development of new purification schemes to achieve the desired level of purity is needed. In this work, the acidic extractant, 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (HEH[EHP])—proposed for application in extractive processes aimed at separating trivalentmore » minor actinides from lanthanides and other fission products—is characterized with respect to its common impurities and their impact on Am(III) stripping in the Actinide Lanthanide SEParation (ALSEP) system. To control impurities in HEH[EHP], existing purification technologies commonly applied for the acidic organophosphorus reagents are reviewed, and a new method specific to HEH[EHP] purification is presented.« less

RACE/A: an architectural account of the interactions between learning, task control, and retrieval dynamics.

PubMed

van Maanen, Leendert; van Rijn, Hedderik; Taatgen, Niels

2012-01-01

This article discusses how sequential sampling models can be integrated in a cognitive architecture. The new theory Retrieval by Accumulating Evidence in an Architecture (RACE/A) combines the level of detail typically provided by sequential sampling models with the level of task complexity typically provided by cognitive architectures. We will use RACE/A to model data from two variants of a picture-word interference task in a psychological refractory period design. These models will demonstrate how RACE/A enables interactions between sequential sampling and long-term declarative learning, and between sequential sampling and task control. In a traditional sequential sampling model, the onset of the process within the task is unclear, as is the number of sampling processes. RACE/A provides a theoretical basis for estimating the onset of sequential sampling processes during task execution and allows for easy modeling of multiple sequential sampling processes within a task. Copyright © 2011 Cognitive Science Society, Inc.

Neural changes associated with semantic processing in healthy aging despite intact behavioral performance.

PubMed

Lacombe, Jacinthe; Jolicoeur, Pierre; Grimault, Stephan; Pineault, Jessica; Joubert, Sven

2015-10-01

Semantic memory recruits an extensive neural network including the left inferior prefrontal cortex (IPC) and the left temporoparietal region, which are involved in semantic control processes, as well as the anterior temporal lobe region (ATL) which is considered to be involved in processing semantic information at a central level. However, little is known about the underlying neuronal integrity of the semantic network in normal aging. Young and older healthy adults carried out a semantic judgment task while their cortical activity was recorded using magnetoencephalography (MEG). Despite equivalent behavioral performance, young adults activated the left IPC to a greater extent than older adults, while the latter group recruited the temporoparietal region bilaterally and the left ATL to a greater extent than younger adults. Results indicate that significant neuronal changes occur in normal aging, mainly in regions underlying semantic control processes, despite an apparent stability in performance at the behavioral level. Copyright © 2015 Elsevier Inc. All rights reserved.

An fMRI-study of locally oriented perception in autism: altered early visual processing of the block design test.

PubMed

Bölte, S; Hubl, D; Dierks, T; Holtmann, M; Poustka, F

2008-01-01

Autism has been associated with enhanced local processing on visual tasks. Originally, this was based on findings that individuals with autism exhibited peak performance on the block design test (BDT) from the Wechsler Intelligence Scales. In autism, the neurofunctional correlates of local bias on this test have not yet been established, although there is evidence of alterations in the early visual cortex. Functional MRI was used to analyze hemodynamic responses in the striate and extrastriate visual cortex during BDT performance and a color counting control task in subjects with autism compared to healthy controls. In autism, BDT processing was accompanied by low blood oxygenation level-dependent signal changes in the right ventral quadrant of V2. Findings indicate that, in autism, locally oriented processing of the BDT is associated with altered responses of angle and grating-selective neurons, that contribute to shape representation, figure-ground, and gestalt organization. The findings favor a low-level explanation of BDT performance in autism.

Mental workload measurement in operator control room using NASA-TLX

NASA Astrophysics Data System (ADS)

Sugarindra, M.; Suryoputro, M. R.; Permana, A. I.

2017-12-01

The workload, encountered a combination of physical workload and mental workload, is a consequence of the activities for workers. Central control room is one department in the oil processing company, employees tasked with monitoring the processing unit for 24 hours nonstop with a combination of 3 shifts in 8 hours. NASA-TLX (NASA Task Load Index) is one of the subjective mental workload measurement using six factors, namely the Mental demand (MD), Physical demand (PD), Temporal demand (TD), Performance (OP), Effort (EF), frustration levels (FR). Measurement of a subjective mental workload most widely used because it has a high degree of validity. Based on the calculation of the mental workload, there at 5 units (DTU, NPU, HTU, DIST and OPS) at the control chamber (94; 83.33; 94.67; 81, 33 and 94.67 respectively) that categorize as very high mental workload. The high level of mental workload on the operator in the Central Control Room is a requirement to have high accuracy, alertness and can make decisions quickly

Cognitive task load in a naval ship control centre: from identification to prediction.

PubMed

Grootjen, M; Neerincx, M A; Veltman, J A

Deployment of information and communication technology will lead to further automation of control centre tasks and an increasing amount of information to be processed. A method for establishing adequate levels of cognitive task load for the operators in such complex environments has been developed. It is based on a model distinguishing three load factors: time occupied, task-set switching, and level of information processing. Application of the method resulted in eight scenarios for eight extremes of task load (i.e. low and high values for each load factor). These scenarios were performed by 13 teams in a high-fidelity control centre simulator of the Royal Netherlands Navy. The results show that the method provides good prediction of the task load that will actually appear in the simulator. The model allowed identification of under- and overload situations showing negative effects on operator performance corresponding to controlled experiments in a less realistic task environment. Tools proposed to keep the operator at an optimum task load are (adaptive) task allocation and interface support.

Enhancing social ability by stimulating right temporoparietal junction.

PubMed

Santiesteban, Idalmis; Banissy, Michael J; Catmur, Caroline; Bird, Geoffrey

2012-12-04

The temporoparietal junction (TPJ) is a key node within the "social brain". Several studies suggest that the TPJ controls representations of the self or another individual across a variety of low-level (agency discrimination, visual perspective taking, control of imitation) and high-level (mentalizing, empathy) sociocognitive processes. We explored whether sociocognitive abilities relying on on-line control of self and other representations could be modulated with transcranial direct current stimulation (tDCS) of TPJ. Participants received excitatory (anodal), inhibitory (cathodal), or sham stimulation before completing three sociocognitive tasks. Anodal stimulation improved the on-line control of self-other representations elicited by the imitation and perspective-taking tasks while not affecting attribution of mental states during a self-referential task devoid of such a requirement. Our findings demonstrate the efficacy of tDCS to improve social cognition and highlight the potential for tDCS to be used as a tool to aid self-other processing in clinical populations. Copyright © 2012 Elsevier Ltd. All rights reserved.

Neurophysiological processes and functional neuroanatomical structures underlying proactive effects of emotional conflicts.

PubMed

Schreiter, Marie Luise; Chmielewski, Witold; Beste, Christian

2018-07-01

There is a strong inter-relation of cognitive and emotional processes as evidenced by emotional conflict monitoring processes. In the cognitive domain, proactive effects of conflicts have widely been studied; i.e. effects of conflicts in the n-1 trial on trial n. Yet, the neurophysiological processes and associated functional neuroanatomical structures underlying such proactive effects during emotional conflicts have not been investigated. This is done in the current study combining EEG recordings with signal decomposition methods and source localization approaches. We show that an emotional conflict in the n-1 trial differentially influences processing of positive and negative emotions in trial n, but not the processing of conflicts in trial n. The dual competition framework stresses the importance of dissociable 'perceptual' and 'response selection' or cognitive control levels for interactive effects of cognition and emotion. Only once these coding levels were isolated in the neurophysiological data, processes explaining the behavioral effects were detectable. The data show that there is not only a close correspondence between theoretical propositions of the dual competition framework and neurophysiological processes. Rather, processing levels conceptualized in the framework operate in overlapping time windows, but are implemented via distinct functional neuroanatomical structures; the precuneus (BA31) and the insula (BA13). It seems that decoding of information in the precuneus, as well as the integration of information during response selection in the insula is more difficult when confronted with angry facial emotions whenever cognitive control resources have been highly taxed by previous conflicts. Copyright © 2018 Elsevier Inc. All rights reserved.

Performance assessment of multi-frequency processing of ICU chest images for enhanced visualization of tubes and catheters

NASA Astrophysics Data System (ADS)

Wang, Xiaohui; Couwenhoven, Mary E.; Foos, David H.; Doran, James; Yankelevitz, David F.; Henschke, Claudia I.

2008-03-01

An image-processing method has been developed to improve the visibility of tube and catheter features in portable chest x-ray (CXR) images captured in the intensive care unit (ICU). The image-processing method is based on a multi-frequency approach, wherein the input image is decomposed into different spatial frequency bands, and those bands that contain the tube and catheter signals are individually enhanced by nonlinear boosting functions. Using a random sampling strategy, 50 cases were retrospectively selected for the study from a large database of portable CXR images that had been collected from multiple institutions over a two-year period. All images used in the study were captured using photo-stimulable, storage phosphor computed radiography (CR) systems. Each image was processed two ways. The images were processed with default image processing parameters such as those used in clinical settings (control). The 50 images were then separately processed using the new tube and catheter enhancement algorithm (test). Three board-certified radiologists participated in a reader study to assess differences in both detection-confidence performance and diagnostic efficiency between the control and test images. Images were evaluated on a diagnostic-quality, 3-megapixel monochrome monitor. Two scenarios were studied: the baseline scenario, representative of today's workflow (a single-control image presented with the window/level adjustments enabled) vs. the test scenario (a control/test image pair presented with a toggle enabled and the window/level settings disabled). The radiologists were asked to read the images in each scenario as they normally would for clinical diagnosis. Trend analysis indicates that the test scenario offers improved reading efficiency while providing as good or better detection capability compared to the baseline scenario.

A retrospective analysis of the change in anti-malarial treatment policy: Peru.

PubMed

Williams, Holly Ann; Vincent-Mark, Arlene; Herrera, Yenni; Chang, O Jaime

2009-04-28

National malaria control programmes must deal with the complex process of changing national malaria treatment guidelines, often without guidance on the process of change. Selecting a replacement drug is only one issue in this process. There is a paucity of literature describing successful malaria treatment policy changes to help guide control programs through this process. To understand the wider context in which national malaria treatment guidelines were formulated in a specific country (Peru). Using qualitative methods (individual and focus group interviews, stakeholder analysis and a review of documents), a retrospective analysis of the process of change in Peru's anti-malarial treatment policy from the early 1990's to 2003 was completed. The decision to change Peru's policies resulted from increasing levels of anti-malarial drug resistance, as well as complaints from providers that the drugs were no longer working. The context of the change occurred in a time in which Peru was changing national governments, which created extreme challenges in moving the change process forward. Peru utilized a number of key strategies successfully to ensure that policy change would occur. This included a) having the process directed by a group who shared a common interest in malaria and who had long-established social and professional networks among themselves, b) engaging in collaborative teamwork among nationals and between nationals and international collaborators, c) respect for and inclusion of district-level staff in all phases of the process, d) reliance on high levels of technical and scientific knowledge, e) use of standardized protocols to collect data, and f) transparency. Although not perfectly or fully implemented by 2003, the change in malaria treatment policy in Peru occurred very quickly, as compared to other countries. They identified a problem, collected the data necessary to justify the change, utilized political will to their favor, approved the policy, and moved to improve malaria control in their country. As such, they offer an excellent example for other countries as they contemplate or embark on policy changes.

An approach to separating the levels of hierarchical structure building in language and mathematics.

PubMed

Makuuchi, Michiru; Bahlmann, Jörg; Friederici, Angela D

2012-07-19

We aimed to dissociate two levels of hierarchical structure building in language and mathematics, namely 'first-level' (the build-up of hierarchical structure with externally given elements) and 'second-level' (the build-up of hierarchical structure with internally represented elements produced by first-level processes). Using functional magnetic resonance imaging, we investigated these processes in three domains: sentence comprehension, arithmetic calculation (using Reverse Polish notation, which gives two operands followed by an operator) and a working memory control task. All tasks required the build-up of hierarchical structures at the first- and second-level, resulting in a similar computational hierarchy across language and mathematics, as well as in a working memory control task. Using a novel method that estimates the difference in the integration cost for conditions of different trial durations, we found an anterior-to-posterior functional organization in the prefrontal cortex, according to the level of hierarchy. Common to all domains, the ventral premotor cortex (PMv) supports first-level hierarchy building, while the dorsal pars opercularis (POd) subserves second-level hierarchy building, with lower activation for language compared with the other two tasks. These results suggest that the POd and the PMv support domain-general mechanisms for hierarchical structure building, with the POd being uniquely efficient for language.

A DMAIC approach for process capability improvement an engine crankshaft manufacturing process

NASA Astrophysics Data System (ADS)

Sharma, G. V. S. S.; Rao, P. Srinivasa

2014-05-01

The define-measure-analyze-improve-control (DMAIC) approach is a five-strata approach, namely DMAIC. This approach is the scientific approach for reducing the deviations and improving the capability levels of the manufacturing processes. The present work elaborates on DMAIC approach applied in reducing the process variations of the stub-end-hole boring operation of the manufacture of crankshaft. This statistical process control study starts with selection of the critical-to-quality (CTQ) characteristic in the define stratum. The next stratum constitutes the collection of dimensional measurement data of the CTQ characteristic identified. This is followed by the analysis and improvement strata where the various quality control tools like Ishikawa diagram, physical mechanism analysis, failure modes effects analysis and analysis of variance are applied. Finally, the process monitoring charts are deployed at the workplace for regular monitoring and control of the concerned CTQ characteristic. By adopting DMAIC approach, standard deviation is reduced from 0.003 to 0.002. The process potential capability index ( C P) values improved from 1.29 to 2.02 and the process performance capability index ( C PK) values improved from 0.32 to 1.45, respectively.

[Establishment and application of "multi-dimensional structure and process dynamic quality control technology system" in preparation products of traditional Chinese medicine (I)].

PubMed

Gu, Jun-Fei; Feng, Liang; Zhang, Ming-Hua; Wu, Chan; Jia, Xiao-Bin

2013-11-01

Safety is an important component of the quality control of traditional Chinese medicine (TCM) preparation products, as well as an important guarantee for clinical application. Currently, the quality control of TCMs in Chinese Pharmacopoeia mostly focuses on indicative compounds for TCM efficacy. TCM preparations are associated with multiple links, from raw materials to products, and each procedure may have impacts on the safety of preparation. We make a summary and analysis on the factors impacting safety during the preparation of TCM products, and then expound the important role of the "multi-dimensional structure and process dynamic quality control technology system" in the quality safety of TCM preparations. Because the product quality of TCM preparation is closely related to the safety, the control over safety-related material basis is an important component of the product quality control of TCM preparations. The implementation of the quality control over the dynamic process of TCM preparations from raw materials to products, and the improvement of the TCM quality safety control at the microcosmic level help lay a firm foundation for the development of the modernization process of TCM preparations.

Cerebrospinal fluid and serum levels of interleukin-8 in patients with multiple sclerosis and its correlation with Q-albumin.

PubMed

Matejčíková, Z; Mareš, J; Sládková, V; Svrčinová, T; Vysloužilová, J; Zapletalová, J; Kaňovský, P

2017-05-01

Multiple sclerosis (MS) is an inflammatory-demyelinating disease of the central nervous system (CNS). Autoimmune inflammation is common in the early stages of MS and is followed by neurodegenerative processes. The result of these changes is axon and myelin breakdown. The paraclinical examination methods are an important part of the diagnostic process. Magnetic resonance imaging of the brain and the cervical spinal cord and an examination of cerebrospinal fluid (CSF) are common paraclinical examinations. An increasing number of studies deal with CSF and serum levels of biomarkers and their role in MS. We hypothesized that the level of interleukin-8 (IL-8) could be different in MS patients than in controls. These differences may be related to damage of the blood-brain barrier (BBB). BBB damage is quantified by the quotient of albumin (Q-alb). CSF and serum levels of IL-8 were assessed in 102 patients with newly diagnosed MS meeting McDonald's revised diagnostic criteria and in 102 subjects as a control group. We then correlated these results with Q-alb. Levels of IL-8 in CSF were significantly higher in MS patients than in controls (Mann-Whitney U test, p<0.0001). Serum levels of IL-8 were significantly lower in MS patients than in controls (Mann-Whitney U test, p=0.018). Spearman's correlation analysis proved a significant correlation between levels of IL-8 and Q-alb. As the etiology of MS is only partially known, research dealing with biomarkers in MS should continue. Better knowledge of etiology can provide a new perspective, especially for treatment. Copyright © 2017 Elsevier B.V. All rights reserved.

Diet and Exercise in Parenthood: A Social Control Perspective

PubMed Central

Reczek, Corinne; Beth Thomeer, Mieke; Lodge, Amy C.; Umberson, Debra; Underhill, Megan

2014-01-01

Previous work on social control—the direct and indirect regulation of an individual’s health behaviors by others—suggests that parent–child relationships promote healthy diet and exercise. Yet parenthood is associated with less healthy diet and exercise patterns. The authors investigated this paradox by examining social control processes in 40 in-depth interviews with mothers and fathers. They found that parenthood involves social control processes that both promote and compromise healthy behavior, contributing to contradictory perceived effects of parenthood on health behavior. Moreover, the dynamics of social control appear to unfold in different ways for mothers and fathers and depend on the child’s gender and life stage, suggesting that gender and age dyads are central to understanding the seemingly contradictory consequences of parenthood at the population level. These articulations of gendered social control processes provide new insight into the consequences of the gendered organization of parenthood for diet and exercise. PMID:25328244

Choosing the Right Systems Integration

NASA Astrophysics Data System (ADS)

Péči, Matúš; Važan, Pavel

2014-12-01

The paper examines systems integration and its main levels at higher levels of control. At present, the systems integration is one of the main aspects participating in the consolidation processes and financial flows of a company. Systems Integration is a complicated emotionconsuming process and it is often a problem to choose the right approach and level of integration. The research focused on four levels of integration, while each of them is characterized by specific conditions. At each level, there is a summary of recommendations and practical experience. The paper also discusses systems integration between the information and MES levels. The main part includes user-level integration where we describe an example of such integration. Finally, we list recommendations and also possible predictions of the systems integration as one of the important factors in the future.

Reactive control processes contributing to residual switch cost and mixing cost across the adult lifespan.

PubMed

Whitson, Lisa R; Karayanidis, Frini; Fulham, Ross; Provost, Alexander; Michie, Patricia T; Heathcote, Andrew; Hsieh, Shulan

2014-01-01

In task-switching paradigms, performance is better when repeating the same task than when alternating between tasks (switch cost) and when repeating a task alone rather than intermixed with another task (mixing cost). These costs remain even after extensive practice and when task cues enable advanced preparation (residual costs). Moreover, residual reaction time mixing cost has been consistently shown to increase with age. Residual switch and mixing costs modulate the amplitude of the stimulus-locked P3b. This mixing effect is disproportionately larger in older adults who also prepare more for and respond more cautiously on these "mixed" repeat trials (Karayanidis et al., 2011). In this paper, we analyze stimulus-locked and response-locked P3 and lateralized readiness potentials to identify whether residual switch and mixing cost arise from the need to control interference at the level of stimulus processing or response processing. Residual mixing cost was associated with control of stimulus-level interference, whereas residual switch cost was also associated with a delay in response selection. In older adults, the disproportionate increase in mixing cost was associated with greater interference at the level of decision-response mapping and response programming for repeat trials in mixed-task blocks. These findings suggest that older adults strategically recruit greater proactive and reactive control to overcome increased susceptibility to post-stimulus interference. This interpretation is consistent with recruitment of compensatory strategies to compensate for reduced repetition benefit rather than an overall decline on cognitive flexibility.

A subsumptive, hierarchical, and distributed vision-based architecture for smart robotics.

PubMed

DeSouza, Guilherme N; Kak, Avinash C

2004-10-01

We present a distributed vision-based architecture for smart robotics that is composed of multiple control loops, each with a specialized level of competence. Our architecture is subsumptive and hierarchical, in the sense that each control loop can add to the competence level of the loops below, and in the sense that the loops can present a coarse-to-fine gradation with respect to vision sensing. At the coarsest level, the processing of sensory information enables a robot to become aware of the approximate location of an object in its field of view. On the other hand, at the finest end, the processing of stereo information enables a robot to determine more precisely the position and orientation of an object in the coordinate frame of the robot. The processing in each module of the control loops is completely independent and it can be performed at its own rate. A control Arbitrator ranks the results of each loop according to certain confidence indices, which are derived solely from the sensory information. This architecture has clear advantages regarding overall performance of the system, which is not affected by the "slowest link," and regarding fault tolerance, since faults in one module does not affect the other modules. At this time we are able to demonstrate the utility of the architecture for stereoscopic visual servoing. The architecture has also been applied to mobile robot navigation and can easily be extended to tasks such as "assembly-on-the-fly."

Reactive control processes contributing to residual switch cost and mixing cost across the adult lifespan

PubMed Central

Whitson, Lisa R.; Karayanidis, Frini; Fulham, Ross; Provost, Alexander; Michie, Patricia T.; Heathcote, Andrew; Hsieh, Shulan

2014-01-01

In task-switching paradigms, performance is better when repeating the same task than when alternating between tasks (switch cost) and when repeating a task alone rather than intermixed with another task (mixing cost). These costs remain even after extensive practice and when task cues enable advanced preparation (residual costs). Moreover, residual reaction time mixing cost has been consistently shown to increase with age. Residual switch and mixing costs modulate the amplitude of the stimulus-locked P3b. This mixing effect is disproportionately larger in older adults who also prepare more for and respond more cautiously on these “mixed” repeat trials (Karayanidis et al., 2011). In this paper, we analyze stimulus-locked and response-locked P3 and lateralized readiness potentials to identify whether residual switch and mixing cost arise from the need to control interference at the level of stimulus processing or response processing. Residual mixing cost was associated with control of stimulus-level interference, whereas residual switch cost was also associated with a delay in response selection. In older adults, the disproportionate increase in mixing cost was associated with greater interference at the level of decision-response mapping and response programming for repeat trials in mixed-task blocks. These findings suggest that older adults strategically recruit greater proactive and reactive control to overcome increased susceptibility to post-stimulus interference. This interpretation is consistent with recruitment of compensatory strategies to compensate for reduced repetition benefit rather than an overall decline on cognitive flexibility. PMID:24817859

An Event-Related Potential Study on the Effects of Cannabis on Emotion Processing

PubMed Central

Troup, Lucy J.; Bastidas, Stephanie; Nguyen, Maia T.; Andrzejewski, Jeremy A.; Bowers, Matthew; Nomi, Jason S.

2016-01-01

The effect of cannabis on emotional processing was investigated using event-related potential paradigms (ERPs). ERPs associated with emotional processing of cannabis users, and non-using controls, were recorded and compared during an implicit and explicit emotional expression recognition and empathy task. Comparisons in P3 component mean amplitudes were made between cannabis users and controls. Results showed a significant decrease in the P3 amplitude in cannabis users compared to controls. Specifically, cannabis users showed reduced P3 amplitudes for implicit compared to explicit processing over centro-parietal sites which reversed, and was enhanced, at fronto-central sites. Cannabis users also showed a decreased P3 to happy faces, with an increase to angry faces, compared to controls. These effects appear to increase with those participants that self-reported the highest levels of cannabis consumption. Those cannabis users with the greatest consumption rates showed the largest P3 deficits for explicit processing and negative emotions. These data suggest that there is a complex relationship between cannabis consumption and emotion processing that appears to be modulated by attention. PMID:26926868

A conceptual framework for intelligent real-time information processing

NASA Technical Reports Server (NTRS)

Schudy, Robert

1987-01-01

By combining artificial intelligence concepts with the human information processing model of Rasmussen, a conceptual framework was developed for real time artificial intelligence systems which provides a foundation for system organization, control and validation. The approach is based on the description of system processing terms of an abstraction hierarchy of states of knowledge. The states of knowledge are organized along one dimension which corresponds to the extent to which the concepts are expressed in terms of the system inouts or in terms of the system response. Thus organized, the useful states form a generally triangular shape with the sensors and effectors forming the lower two vertices and the full evaluated set of courses of action the apex. Within the triangle boundaries are numerous processing paths which shortcut the detailed processing, by connecting incomplete levels of analysis to partially defined responses. Shortcuts at different levels of abstraction include reflexes, sensory motor control, rule based behavior, and satisficing. This approach was used in the design of a real time tactical decision aiding system, and in defining an intelligent aiding system for transport pilots.

Distinguishing Long-Term Controls on Fluvial Architecture in the Lance Formation, Bighorn Basin, Wyoming

NASA Astrophysics Data System (ADS)

McHarge, J. L.; Hajek, E. A.; Heller, P. L.

2007-12-01

Allogenic processes are considered a prime control on the stratigraphic distribution of channel bodies, however, recent studies have indicated that autogenic stratigraphic organization may occur within fluvial systems on basin- filling time scales (105-106 years). Groupings or clusters of closely-spaced channel bodies can be produced by several different mechanisms, including both allogenic and autogenic processes. Commonly, sand- dominated intervals in stratigraphic successions are interpreted as incised-valley fills produced by base-level changes. In contrast, long-timescale organization of river avulsion can generate similar stratigraphic patterns. For example, sand-dominated intervals in the fluvial Lance Formation (Maastrichtian; Bighorn Basin, WY) have been interpreted as incised-valley fills formed during sea-level lowstand. However, closely-spaced sand bodies in the Ferris Formation (Lance equivalent; Hanna Basin, WY) are interpreted as aggradational in origin, and have been compared to autogenic avulsion stratigraphy produced in experimental basins. We evaluate the Lance Formation in the southern Bighorn Basin in an effort to determine whether these sand-dominated intervals are truly incised- valley fills resulting from sea-level changes, or if they were generated by autogenic processes. The Lance Formation crops out in the western and southern margins of the basin, exposing relatively proximal and distal portions of the system. By comparing alluvial architecture between exposures, we evaluate similarities and differences from upstream to downstream and look for evidence of intrinsic and extrinsic controls on deposition. In both localities, the Lance Formation comprises multi-story sheet sandstones and smaller, single-story sandstones. Observed changes from upstream to downstream in the system include: 1) increasing paleoflow depths (from ~30-60 cm to ~70-120 cm); 2) decreasing preservation of fine-grained material within channel bodies; 3) increasing proportion of amalgamated, multi-story sand bodies; and 4) increasing lateral continuity of multi-story sand bodies. These results indicate that upstream, channel-body spacing is dominantly controlled by aggradational processes and may be the result of autogenic avulsion clustering, whereas downstream, evidence of incision and amalgamation indicate that base-level may have limited and controlled sand-body architecture.

Nuclear propulsion control and health monitoring

NASA Technical Reports Server (NTRS)

Walter, P. B.; Edwards, R. M.

1993-01-01

An integrated control and health monitoring architecture is being developed for the Pratt & Whitney XNR2000 nuclear rocket. Current work includes further development of the dynamic simulation modeling and the identification and configuration of low level controllers to give desirable performance for the various operating modes and faulted conditions. Artificial intelligence and knowledge processing technologies need to be investigated and applied in the development of an intelligent supervisory controller module for this control architecture.

Nuclear propulsion control and health monitoring

NASA Astrophysics Data System (ADS)

Walter, P. B.; Edwards, R. M.

1993-11-01

An integrated control and health monitoring architecture is being developed for the Pratt & Whitney XNR2000 nuclear rocket. Current work includes further development of the dynamic simulation modeling and the identification and configuration of low level controllers to give desirable performance for the various operating modes and faulted conditions. Artificial intelligence and knowledge processing technologies need to be investigated and applied in the development of an intelligent supervisory controller module for this control architecture.

Implementation of "Quality by Design (QbD)" Approach for the Development of 5-Fluorouracil Loaded Thermosensitive Hydrogel.

PubMed

Dalwadi, Chintan; Patel, Gayatri

2016-01-01

The purpose of this study was to investigate Quality by Design (QbD) principle for the preparation of hydrogel products to prove both practicability and utility of executing QbD concept to hydrogel based controlled release systems. Product and process understanding will help in decreasing the variability of critical material and process parameters, which give quality product output and reduce the risk. This study includes the identification of the Quality Target Product Profiles (QTPPs) and Critical Quality Attributes (CQAs) from literature or preliminary studies. To identify and control the variability in process and material attributes, two tools of QbD was utilized, Quality Risk Management (QRM) and Experimental Design. Further, it helps to identify the effect of these attributes on CQAs. Potential risk factors were identified from fishbone diagram and screened by risk assessment and optimized by 3-level 2- factor experimental design with center points in triplicate, to analyze the precision of the target process. This optimized formulation was further characterized by gelling time, gelling temperature, rheological parameters, in-vitro biodegradation and in-vitro drug release. Design space was created using experimental design tool that gives the control space and working within this controlled space reduces all the failure modes below the risk level. In conclusion, QbD approach with QRM tool provides potent and effectual pyramid to enhance the quality into the hydrogel.

A reliable control system for measurement on film thickness in copper chemical mechanical planarization system

NASA Astrophysics Data System (ADS)

Li, Hongkai; Qu, Zilian; Zhao, Qian; Tian, Fangxin; Zhao, Dewen; Meng, Yonggang; Lu, Xinchun

2013-12-01

In recent years, a variety of film thickness measurement techniques for copper chemical mechanical planarization (CMP) are subsequently proposed. In this paper, the eddy-current technique is used. In the control system of the CMP tool developed in the State Key Laboratory of Tribology, there are in situ module and off-line module for measurement subsystem. The in situ module can get the thickness of copper film on wafer surface in real time, and accurately judge when the CMP process should stop. This is called end-point detection. The off-line module is used for multi-points measurement after CMP process, in order to know the thickness of remained copper film. The whole control system is structured with two levels, and the physical connection between the upper and the lower is achieved by the industrial Ethernet. The process flow includes calibration and measurement, and there are different algorithms for two modules. In the process of software development, C++ is chosen as the programming language, in combination with Qt OpenSource to design two modules' GUI and OPC technology to implement the communication between the two levels. In addition, the drawing function is developed relying on Matlab, enriching the software functions of the off-line module. The result shows that the control system is running stably after repeated tests and practical operations for a long time.

A reliable control system for measurement on film thickness in copper chemical mechanical planarization system.

PubMed

Li, Hongkai; Qu, Zilian; Zhao, Qian; Tian, Fangxin; Zhao, Dewen; Meng, Yonggang; Lu, Xinchun

2013-12-01

In recent years, a variety of film thickness measurement techniques for copper chemical mechanical planarization (CMP) are subsequently proposed. In this paper, the eddy-current technique is used. In the control system of the CMP tool developed in the State Key Laboratory of Tribology, there are in situ module and off-line module for measurement subsystem. The in situ module can get the thickness of copper film on wafer surface in real time, and accurately judge when the CMP process should stop. This is called end-point detection. The off-line module is used for multi-points measurement after CMP process, in order to know the thickness of remained copper film. The whole control system is structured with two levels, and the physical connection between the upper and the lower is achieved by the industrial Ethernet. The process flow includes calibration and measurement, and there are different algorithms for two modules. In the process of software development, C++ is chosen as the programming language, in combination with Qt OpenSource to design two modules' GUI and OPC technology to implement the communication between the two levels. In addition, the drawing function is developed relying on Matlab, enriching the software functions of the off-line module. The result shows that the control system is running stably after repeated tests and practical operations for a long time.

A reliable control system for measurement on film thickness in copper chemical mechanical planarization system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Hongkai; Qu, Zilian; Zhao, Qian

In recent years, a variety of film thickness measurement techniques for copper chemical mechanical planarization (CMP) are subsequently proposed. In this paper, the eddy-current technique is used. In the control system of the CMP tool developed in the State Key Laboratory of Tribology, there are in situ module and off-line module for measurement subsystem. The in situ module can get the thickness of copper film on wafer surface in real time, and accurately judge when the CMP process should stop. This is called end-point detection. The off-line module is used for multi-points measurement after CMP process, in order to knowmore » the thickness of remained copper film. The whole control system is structured with two levels, and the physical connection between the upper and the lower is achieved by the industrial Ethernet. The process flow includes calibration and measurement, and there are different algorithms for two modules. In the process of software development, C++ is chosen as the programming language, in combination with Qt OpenSource to design two modules’ GUI and OPC technology to implement the communication between the two levels. In addition, the drawing function is developed relying on Matlab, enriching the software functions of the off-line module. The result shows that the control system is running stably after repeated tests and practical operations for a long time.« less

On Efficient Multigrid Methods for Materials Processing Flows with Small Particles

NASA Technical Reports Server (NTRS)

Thomas, James (Technical Monitor); Diskin, Boris; Harik, VasylMichael

2004-01-01

Multiscale modeling of materials requires simulations of multiple levels of structural hierarchy. The computational efficiency of numerical methods becomes a critical factor for simulating large physical systems with highly desperate length scales. Multigrid methods are known for their superior efficiency in representing/resolving different levels of physical details. The efficiency is achieved by employing interactively different discretizations on different scales (grids). To assist optimization of manufacturing conditions for materials processing with numerous particles (e.g., dispersion of particles, controlling flow viscosity and clusters), a new multigrid algorithm has been developed for a case of multiscale modeling of flows with small particles that have various length scales. The optimal efficiency of the algorithm is crucial for accurate predictions of the effect of processing conditions (e.g., pressure and velocity gradients) on the local flow fields that control the formation of various microstructures or clusters.

Distancing from experienced self: how global-versus-local perception affects estimation of psychological distance.

PubMed

Liberman, Nira; Förster, Jens

2009-08-01

In 4 studies, the authors examined the prediction derived from construal level theory (CLT) that higher level of perceptual construal would enhance estimated egocentric psychological distance. The authors primed participants with global perception, local perception, or both (the control condition). Relative to the control condition, global processing made participants estimate larger psychological distances in time (Study 1), space (Study 2), social distance (Study 3), and hypotheticality (Study 4). Local processing had the opposite effect. Consistent with CLT, all studies show that the effect of global-versus-local processing did emerge when participants estimated egocentric distances, which are distances from the experienced self in the here and now, but did not emerge with temporal distances not from now (Study 1), spatial distances not from here (Study 2), social distances not from the self (Study 3), or hypothetical events that did not involve altering an experienced reality (Study 4).

Implementation and benefits of advanced process control for lithography CD and overlay

NASA Astrophysics Data System (ADS)

Zavyalova, Lena; Fu, Chong-Cheng; Seligman, Gary S.; Tapp, Perry A.; Pol, Victor

2003-05-01

Due to the rapidly reduced imaging process windows and increasingly stingent device overlay requirements, sub-130 nm lithography processes are more severely impacted than ever by systamic fault. Limits on critical dimensions (CD) and overlay capability further challenge the operational effectiveness of a mix-and-match environment using multiple lithography tools, as such mode additionally consumes the available error budgets. Therefore, a focus on advanced process control (APC) methodologies is key to gaining control in the lithographic modules for critical device levels, which in turn translates to accelerated yield learning, achieving time-to-market lead, and ultimately a higher return on investment. This paper describes the implementation and unique challenges of a closed-loop CD and overlay control solution in high voume manufacturing of leading edge devices. A particular emphasis has been placed on developing a flexible APC application capable of managing a wide range of control aspects such as process and tool drifts, single and multiple lot excursions, referential overlay control, 'special lot' handling, advanced model hierarchy, and automatic model seeding. Specific integration cases, including the multiple-reticle complementary phase shift lithography process, are discussed. A continuous improvement in the overlay and CD Cpk performance as well as the rework rate has been observed through the implementation of this system, and the results are studied.

Monitoring Calcium in Trout Eggs Exposed to Hydrazine.

DTIC Science & Technology

1981-07-10

differentiation processes (Chapman, 1980). The high level of calcium in the notochord can be attributed to poor circulation which is characteristic of this...healthy muscle of the same individual. The notochord of the 8.0 mg/P group showed a higher calcium level than the control group. The chorion did not...calcium can alter the process . The above would suggest that even if some hydrazine is converted to N2 and thereby produce the gas bubble disease

Review of Findings for Human Performance Contribution to Risk in Operating Events

DTIC Science & Technology

2002-03-01

and loss of DC power. Key to this event was failure to control setpoints on safety-related equipment and failure to maintain the load tap changer...34 Therefore, "to optimize task execution at the job site, it is important to align organizational processes and values." Effective team skills are an...reactor was blocked and the water level rapidly dropped to the automatic low-level scram setpoint . Human Performance Issues Control rods were fully

Accreditation of specialized asthma units for adults in Spain: an applicable experience for the management of difficult-to-control asthma

PubMed Central

Cisneros, Carolina; Díaz-Campos, Rocío Magdalena; Marina, Núria; Melero, Carlos; Padilla, Alicia; Pascual, Silvia; Pinedo, Celia; Trisán, Andrea

2017-01-01

This paper, developed by consensus of staff physicians of accredited asthma units for the management of severe asthma, presents information on the process and requirements for already-existing asthma units to achieve official accreditation by the Spanish Society of Pneumology and Thoracic Surgery (SEPAR). Three levels of specialized asthma care have been established based on available resources, which include specialized units for highly complex asthma, specialized asthma units, and basic asthma units. Regardless of the level of accreditation obtained, the distinction of “excellence” could be granted when more requirements in the areas of provision of care, technical and human resources, training in asthma, and teaching and research activities were met at each level. The Spanish experience in the process of accreditation of specialized asthma units, particularly for the care of patients with difficult-to-control asthma, may be applicable to other health care settings. PMID:28533690

Inventory Control System by Using Vendor Managed Inventory (VMI)

NASA Astrophysics Data System (ADS)

Sabila, Alzena Dona; Mustafid; Suryono

2018-02-01

The inventory control system has a strategic role for the business in managing inventory operations. Management of conventional inventory creates problems in the stock of goods that often runs into vacancies and excess goods at the retail level. This study aims to build inventory control system that can maintain the stability of goods availability at the retail level. The implementation of Vendor Managed Inventory (VMI) method on inventory control system provides transparency of sales data and inventory of goods at retailer level to supplier. Inventory control is performed by calculating safety stock and reorder point of goods based on sales data received by the system. Rule-based reasoning is provided on the system to facilitate the monitoring of inventory status information, thereby helping the process of inventory updates appropriately. Utilization of SMS technology is also considered as a medium of collecting sales data in real-time due to the ease of use. The results of this study indicate that inventory control using VMI ensures the availability of goods ± 70% and can reduce the accumulation of goods ± 30% at the retail level.

Self-organizing high-order cognitive functions in artificial agents: implications for possible prefrontal cortex mechanisms.

PubMed

Maniadakis, Michail; Trahanias, Panos; Tani, Jun

2012-09-01

In our daily life, we often adapt plans and behaviors according to dynamically changing world circumstances, selecting activities that make us feel more confident about the future. In this adaptation, the prefrontal cortex (PFC) is believed to have an important role, applying executive control on other cognitive processes to achieve context switching and confidence monitoring; however, many questions remain open regarding the nature of neural processes supporting executive control. The current work explores possible mechanisms of this high-order cognitive function, transferring executing control in the domain of artificial cognitive systems. In particular, we study the self-organization of artificial neural networks accomplishing a robotic rule-switching task analogous to the Wisconsin Card Sorting Test. The obtained results show that behavioral rules may be encoded in neuro-dynamic attractors, with their geometric arrangements in phase space affecting the shaping of confidence. Analysis of the emergent dynamical structures suggests possible explanations of the interactions of high-level and low-level processes in the real brain. Copyright © 2012 Elsevier Ltd. All rights reserved.

Tank Pressure Control Experiment on the Space Shuttle

NASA Technical Reports Server (NTRS)

1989-01-01

The tank pressure control experiment is a demonstration of NASA intent to develop new technology for low-gravity management of the cryogenic fluids that will be required for future space systems. The experiment will use freon as the test fluid to measure the effects of jet-induced fluid mixing on storage tank pressure and will produce data on low-gravity mixing processes critical to the design of on-orbit cryogenic storage and resupply systems. Basic data on fluid motion and thermodynamics in low gravity is limited, but such data is critical to the development of space transfer vehicles and spacecraft resupply facilities. An in-space experiment is needed to obtain reliable data on fluid mixing and pressure control because none of the available microgravity test facilities provide a low enough gravity level for a sufficient duration to duplicate in-space flow patterns and thermal processes. Normal gravity tests do not represent the fluid behavior properly; drop-tower tests are limited in length of time available; aircraft low-gravity tests cannot provide the steady near-zero gravity level and long duration needed to study the subtle processes expected in space.

Ambiguous meanings of projects as facilitators of sensegiving.

PubMed

Lunkka, Nina; Suhonen, Marjo

2015-10-01

To describe mid-level nurse managers' experiences of sensegiving in the context of hospital projects. Sensegiving is about shaping and affecting how employees see themselves, their work and issues related to their work. It has been little studied in the context of hospital projects from mid-level nurse managers' point of view. Mid-level nurse managers (n = 10) were interviewed about their experiences of projects from the viewpoint of sensegiving during change processes. Data was analysed using discourse analysis. Three repertoires were constructed from the data: the repertoires of regeneration, control and humane. Projects were considered as appropriate ways for sensegiving in hospitals from the viewpoint of mid-level nurse managers. In order to use projects effectively in hospitals as means for change management mid-level nurse managers ought to enhance their role as interpreters during the change process (i.e. strengthen their visioning, talk and dialogue skills). Training on the nature of change as a social and interactive process could deepen mid-level nurse managers' understanding of the change process in the context of hospital projects. © 2014 John Wiley & Sons Ltd.

Levels of thrombopoietin in aqueous humor of patients with noninfectious acute anterior uveitis

PubMed Central

Mondejar, José-Juan; Salom, David; Garcia-Delpech, Salvador; Diaz-Llopis, Manuel

2015-01-01

Purpose To measure thrombopoietin (TPO) levels in the serum and aqueous humors of patients with noninfectious acute anterior uveitis. Methods A prospective, comparative, controlled study. Serum and aqueous humors were obtained from the eyes of 16 patients with noninfectious acute anterior uveitis. TPO levels were measured using an enzyme-linked immunosorbent assay (ELISA). The results obtained were compared with those of a control group. Results Serum concentrations of TPO were not significantly different between control individuals and patients with active anterior uveitis. Aqueous humor TPO levels were 54.46±16.24 pg/mL in the eyes of patients with uveitis, and 34.32±11.63 pg/mL in the eyes of controls. The difference between the two groups was significant (Mann–Whitney U-test for independent data, P=0.0008), with uveitis patients exhibiting significantly higher levels of TPO. Conclusion The high levels of TPO in the aqueous humors of uveitis patients points toward a cytoprotective role of this factor in inflammatory repair processes and the recovery of tissue homeostasis. PMID:26203218

Design of supply chain in fuzzy environment

NASA Astrophysics Data System (ADS)

Rao, Kandukuri Narayana; Subbaiah, Kambagowni Venkata; Singh, Ganja Veera Pratap

2013-05-01

Nowadays, customer expectations are increasing and organizations are prone to operate in an uncertain environment. Under this uncertain environment, the ultimate success of the firm depends on its ability to integrate business processes among supply chain partners. Supply chain management emphasizes cross-functional links to improve the competitive strategy of organizations. Now, companies are moving from decoupled decision processes towards more integrated design and control of their components to achieve the strategic fit. In this paper, a new approach is developed to design a multi-echelon, multi-facility, and multi-product supply chain in fuzzy environment. In fuzzy environment, mixed integer programming problem is formulated through fuzzy goal programming in strategic level with supply chain cost and volume flexibility as fuzzy goals. These fuzzy goals are aggregated using minimum operator. In tactical level, continuous review policy for controlling raw material inventories in supplier echelon and controlling finished product inventories in plant as well as distribution center echelon is considered as fuzzy goals. A non-linear programming model is formulated through fuzzy goal programming using minimum operator in the tactical level. The proposed approach is illustrated with a numerical example.

Severe tinnitus and its effect on selective and divided attention.

PubMed

Stevens, Catherine; Walker, Gary; Boyer, Morten; Gallagher, Melinda

2007-05-01

The effect of chronic, severe tinnitus on two visual tasks was investigated. A general depletion of resources hypothesis states that overall performance would be impaired in a tinnitus group relative to a control group whereas a controlled processing hypothesis states that only tasks that are demanding, requiring strategic processes, are affected. Eleven participants who had experienced severe tinnitus for more than two years comprised the tinnitus group. A control group was matched for age and verbal IQ. Levels of anxiety, depression, and high frequency average hearing level were treated as covariates. Tasks consisted of the say-word (easy) and say-color (demanding) conditions of the Stroop task, a single (baseline) reaction time (RT) task, and dual tasks involving word reading or category naming while performing a concurrent RT task. Results supported the general depletion of resources hypothesis: RT of the tinnitus group was slower in both conditions of the Stroop task, and in the word reading and category naming conditions of the dual task. Differences were not attributable to high frequency average hearing level, anxiety, or depression.

Monitoring sodium levels in commercially processed and restaurant foods - dataset and webpages.

USDA-ARS?s Scientific Manuscript database

Nutrient Data Laboratory (NDL), Agriculture Research Service (ARS) in collaboration with Food Surveys Research Group, ARS, and the Centers for Disease Control and Prevention has been monitoring commercially processed and restaurant foods in the United States since 2010. About 125 highly consumed, s...

Orbiter data reduction complex data processing requirements for the OFT mission evaluation team (level C)

NASA Technical Reports Server (NTRS)

1979-01-01

This document addresses requirements for post-test data reduction in support of the Orbital Flight Tests (OFT) mission evaluation team, specifically those which are planned to be implemented in the ODRC (Orbiter Data Reduction Complex). Only those requirements which have been previously baselined by the Data Systems and Analysis Directorate configuration control board are included. This document serves as the control document between Institutional Data Systems Division and the Integration Division for OFT mission evaluation data processing requirements, and shall be the basis for detailed design of ODRC data processing systems.

Impact of hospital care on incidence of bloodstream infection: the evaluation of processes and indicators in infection control study.

PubMed Central

Kritchevsky, S. B.; Braun, B. I.; Wong, E. S.; Solomon, S. L.; Steele, L.; Richards, C.; Simmons, B. P.

2001-01-01

The Evaluation of Processes and Indicators in Infection Control (EPIC) study assesses the relationship between hospital care and rates of central venous catheter-associated primary bacteremia in 54 intensive-care units (ICUs) in the United States and 14 other countries. Using ICU rather than the patient as the primary unit of statistical analysis permits evaluation of factors that vary at the ICU level. The design of EPIC can serve as a template for studies investigating the relationship between process and event rates across health-care institutions. PMID:11294704

Stabilizing laser energy density on a target during pulsed laser deposition of thin films

DOEpatents

Dowden, Paul C.; Jia, Quanxi

2016-05-31

A process for stabilizing laser energy density on a target surface during pulsed laser deposition of thin films controls the focused laser spot on the target. The process involves imaging an image-aperture positioned in the beamline. This eliminates changes in the beam dimensions of the laser. A continuously variable attenuator located in between the output of the laser and the imaged image-aperture adjusts the energy to a desired level by running the laser in a "constant voltage" mode. The process provides reproducibility and controllability for deposition of electronic thin films by pulsed laser deposition.

Theory of agent-based market models with controlled levels of greed and anxiety

NASA Astrophysics Data System (ADS)

Papadopoulos, P.; Coolen, A. C. C.

2010-01-01

We use generating functional analysis to study minority-game-type market models with generalized strategy valuation updates that control the psychology of agents' actions. The agents' choice between trend-following and contrarian trading, and their vigor in each, depends on the overall state of the market. Even in 'fake history' models, the theory now involves an effective overall bid process (coupled to the effective agent process) which can exhibit profound remanence effects and new phase transitions. For some models the bid process can be solved directly, others require Maxwell-construction-type approximations.

Walk-through survey report: Control technology for integrated circuit fabrication, Xerox Corporation, El Segundo, California

NASA Astrophysics Data System (ADS)

Mihlan, G. J.; Ungers, L. J.; Smith, R. K.; Mitchell, R. I.; Jones, J. H.

1983-05-01

A preliminary control technology assessment survey was conducted at the facility which manufactures N-channel metal oxide semiconductor (NMOS) integrated circuits. The facility has industrial hygiene review procedures for evaluating all new and existing process equipment. Employees are trained in safety, use of personal protective equipment, and emergency response. Workers potentially exposed to arsenic are monitored for urinary arsenic levels. The facility should be considered a candidate for detailed study based on the diversity of process operations encountered and the use of state-of-the-art technology and process equipment.

Graphics Processing Unit (GPU) implementation of image processing algorithms to improve system performance of the Control, Acquisition, Processing, and Image Display System (CAPIDS) of the Micro-Angiographic Fluoroscope (MAF).

PubMed

Vasan, S N Swetadri; Ionita, Ciprian N; Titus, A H; Cartwright, A N; Bednarek, D R; Rudin, S

2012-02-23

We present the image processing upgrades implemented on a Graphics Processing Unit (GPU) in the Control, Acquisition, Processing, and Image Display System (CAPIDS) for the custom Micro-Angiographic Fluoroscope (MAF) detector. Most of the image processing currently implemented in the CAPIDS system is pixel independent; that is, the operation on each pixel is the same and the operation on one does not depend upon the result from the operation on the other, allowing the entire image to be processed in parallel. GPU hardware was developed for this kind of massive parallel processing implementation. Thus for an algorithm which has a high amount of parallelism, a GPU implementation is much faster than a CPU implementation. The image processing algorithm upgrades implemented on the CAPIDS system include flat field correction, temporal filtering, image subtraction, roadmap mask generation and display window and leveling. A comparison between the previous and the upgraded version of CAPIDS has been presented, to demonstrate how the improvement is achieved. By performing the image processing on a GPU, significant improvements (with respect to timing or frame rate) have been achieved, including stable operation of the system at 30 fps during a fluoroscopy run, a DSA run, a roadmap procedure and automatic image windowing and leveling during each frame.

Active controllers and the time duration to learn a task

NASA Technical Reports Server (NTRS)

Repperger, D. W.; Goodyear, C.

1986-01-01

An active controller was used to help train naive subjects involved in a compensatory tracking task. The controller is called active in this context because it moves the subject's hand in a direction to improve tracking. It is of interest here to question whether the active controller helps the subject to learn a task more rapidly than the passive controller. Six subjects, inexperienced to compensatory tracking, were run to asymptote root mean square error tracking levels with an active controller or a passive controller. The time required to learn the task was defined several different ways. The results of the different measures of learning were examined across pools of subjects and across controllers using statistical tests. The comparison between the active controller and the passive controller as to their ability to accelerate the learning process as well as reduce levels of asymptotic tracking error is reported here.

Susceptibility of materials processing experiments to low-level accelerations

NASA Technical Reports Server (NTRS)

Naumann, R. J.

1981-01-01

The types of material processing experiments being considered for shuttle can be grouped into four categories: (1) contained solidification experiment; (2) quasicontainerless experiments; (3) containerless experiments; and (4) fluids experiments. Low level steady acceleration, compensated and uncompensated transient accelerations, and rotation induced flow factors that must be considered in the acceleration environment of a space vehicle whose importance depends on the type of experiment being performed. Some control of these factors may be exercised by the location and orientation of the experiment relative to shuttle and by the orbit vehicle attitude chosen for mission. The effects of the various residual accelerations can have serious consequence to the control of the experiment and must be factored into the design and operation of the apparatus.

Algorithm for solving of two-level hierarchical minimax program control problem of final state the regional socio-economic system in the presence of risks

NASA Astrophysics Data System (ADS)

Shorikov, A. F.

2017-10-01

In this paper we study the problem of optimization of guaranteed result for program control by the final state of regional social and economic system in the presence of risks. For this problem we propose a mathematical model in the form of two-level hierarchical minimax program control problem of the final state of this process with incomplete information. For solving of its problem we constructed the common algorithm that has a form of a recurrent procedure of solving a linear programming and a finite optimization problems.

New S control chart using skewness correction method for monitoring process dispersion of skewed distributions

NASA Astrophysics Data System (ADS)

Atta, Abdu; Yahaya, Sharipah; Zain, Zakiyah; Ahmed, Zalikha

2017-11-01

Control chart is established as one of the most powerful tools in Statistical Process Control (SPC) and is widely used in industries. The conventional control charts rely on normality assumption, which is not always the case for industrial data. This paper proposes a new S control chart for monitoring process dispersion using skewness correction method for skewed distributions, named as SC-S control chart. Its performance in terms of false alarm rate is compared with various existing control charts for monitoring process dispersion, such as scaled weighted variance S chart (SWV-S); skewness correction R chart (SC-R); weighted variance R chart (WV-R); weighted variance S chart (WV-S); and standard S chart (STD-S). Comparison with exact S control chart with regards to the probability of out-of-control detections is also accomplished. The Weibull and gamma distributions adopted in this study are assessed along with the normal distribution. Simulation study shows that the proposed SC-S control chart provides good performance of in-control probabilities (Type I error) in almost all the skewness levels and sample sizes, n. In the case of probability of detection shift the proposed SC-S chart is closer to the exact S control chart than the existing charts for skewed distributions, except for the SC-R control chart. In general, the performance of the proposed SC-S control chart is better than all the existing control charts for monitoring process dispersion in the cases of Type I error and probability of detection shift.

Polyhedral Interpolation for Optimal Reaction Control System Jet Selection

NASA Technical Reports Server (NTRS)

Gefert, Leon P.; Wright, Theodore

2014-01-01

An efficient algorithm is described for interpolating optimal values for spacecraft Reaction Control System jet firing duty cycles. The algorithm uses the symmetrical geometry of the optimal solution to reduce the number of calculations and data storage requirements to a level that enables implementation on the small real time flight control systems used in spacecraft. The process minimizes acceleration direction errors, maximizes control authority, and minimizes fuel consumption.

An Analysis of the Navy Regional Data Automation Center (NARDAC) chargeback System

DTIC Science & Technology

1986-09-01

addition, operational control is concerned with performing predefined activities whereas management control relates to the organiza- tion’s goals and...In effect, the management control system monitors the progress of operations and alerts the "appropriate management level" when performance as measured...architecture, the financial control processes, and the audit function ( Brandon , 1978; Anderson, 1983). In an operating DP environment, however, non-financial

Pitting temporal against spatial integration in schizophrenic patients.

PubMed

Herzog, Michael H; Brand, Andreas

2009-06-30

Schizophrenic patients show strong impairments in visual backward masking possibly caused by deficits on the early stages of visual processing. The underlying aberrant mechanisms are not clearly understood. Spatial as well as temporal processing deficits have been proposed. Here, by combining a spatial with a temporal integration paradigm, we show further evidence that temporal but not spatial processing is impaired in schizophrenic patients. Eleven schizophrenic patients and ten healthy controls were presented with sequences composed of Vernier stimuli. Patients needed significantly longer presentation times for sequentially presented Vernier stimuli to reach a performance level comparable to that of healthy controls (temporal integration deficit). When we added spatial contextual elements to some of the Vernier stimuli, performance changed in a complex but comparable manner in patients and controls (intact spatial integration). Hence, temporal but not spatial processing seems to be deficient in schizophrenia.

Interfacing LabVIEW With Instrumentation for Electronic Failure Analysis and Beyond

NASA Technical Reports Server (NTRS)

Buchanan, Randy K.; Bryan, Coleman; Ludwig, Larry

1996-01-01

The Laboratory Virtual Instrumentation Engineering Workstation (LabVIEW) software is designed such that equipment and processes related to control systems can be operationally lined and controlled by the use of a computer. Various processes within the failure analysis laboratories of NASA's Kennedy Space Center (KSC) demonstrate the need for modernization and, in some cases, automation, using LabVIEW. An examination of procedures and practices with the Failure Analaysis Laboratory resulted in the conclusion that some device was necessary to elevate the potential users of LabVIEW to an operational level in minimum time. This paper outlines the process involved in creating a tutorial application to enable personnel to apply LabVIEW to their specific projects. Suggestions for furthering the extent to which LabVIEW is used are provided in the areas of data acquisition and process control.

The influence of the COMT genotype in the underlying functional brain activity of context processing in schizophrenia and in relatives.

PubMed

Lopez-Garcia, Pilar; Cristobal-Huerta, Alexandra; Young Espinoza, Leslie; Molero, Patricio; Ortuño Sanchez-Pedreño, Felipe; Hernández-Tamames, Juan Antonio

2016-11-03

Context processing deficits have been shown to be present in chronic and first episode schizophrenia patients and in their relatives. This cognitive process is linked to frontal functioning and is highly dependent on dopamine levels in the prefrontal cortex (PFC). The catechol-O-methyltransferase (COMT) enzyme plays a prominent role in regulating dopamine levels in PFC. Genotypic variations in the functional polymorphism Val(158)Met COMT appear to have an impact in dopamine signaling in the PFC of healthy subjects and schizophrenia patients. We aimed to explore the effect of the Val(158)Met COMT polymorphism on brain activation during the performance of a context processing task in healthy subjects, schizophrenia spectrum patients and their healthy relatives. 56 participants performed the Dot Probe Expectancy task (DPX) during the fMRI session. Subjects were genotyped and only the Val and Met homozygotes participated in the study. Schizophrenia spectrum patients and their relatives showed worse performance on context processing measures than healthy control subjects. The Val allele was associated with more context processing errors in healthy controls and in relatives compared to patients. There was a greater recruitment of frontal areas (supplementary motor area/cingulate gyrus) during context processing in patients relative to healthy controls. Met homozygotes subjects activated more frontal areas than Val homozygotes subjects. The Val(158)Met COMT polymorphism influences context processing and on its underlying brain activation, showing less recruitment of frontal areas in the subjects with the genotype associated to lower dopamine availability in PFC. Copyright © 2016. Published by Elsevier Inc.

A Conceptual Model of the Air Force Logistics Pipeline

DTIC Science & Technology

1989-09-01

Contracting Process . ....... 138 Industrial Capacity .. ......... 140 The Disposal Pipeline Subsystem ....... 142 Collective Pipeline Models...Explosion of " Industry ," Acquisition and Production Process .... ............ 202 60. First Level Explosion of "Attrition," the Disposal Process...Terminology and Phrases, a publication of The American Production and Inventory Control Society ( APICS ). This dictionary defines 5 "pipeline stock" as the

The Effects of a Web-Based Nursing Process Documentation Program on Stress and Anxiety of Nursing Students in South Korea.

PubMed

Lee, Eunjoo; Noh, Hyun Kyung

2016-01-01

To examine the effects of a web-based nursing process documentation system on the stress and anxiety of nursing students during their clinical practice. A quasi-experimental design was employed. The experimental group (n = 110) used a web-based nursing process documentation program for their case reports as part of assignments for a clinical practicum, whereas the control group (n = 106) used traditional paper-based case reports. Stress and anxiety levels were measured with a numeric rating scale before, 2 weeks after, and 4 weeks after using the web-based nursing process documentation program during a clinical practicum. The data were analyzed using descriptive statistics, t tests, chi-square tests, and repeated-measures analyses of variance. Nursing students who used the web-based nursing process documentation program showed significant lower levels of stress and anxiety than the control group. A web-based nursing process documentation program could be used to reduce the stress and anxiety of nursing students during clinical practicum, which ultimately would benefit nursing students by increasing satisfaction with and effectiveness of clinical practicum. © 2015 NANDA International, Inc.

Non-Markovianity in the optimal control of an open quantum system described by hierarchical equations of motion

NASA Astrophysics Data System (ADS)

Mangaud, E.; Puthumpally-Joseph, R.; Sugny, D.; Meier, C.; Atabek, O.; Desouter-Lecomte, M.

2018-04-01

Optimal control theory is implemented with fully converged hierarchical equations of motion (HEOM) describing the time evolution of an open system density matrix strongly coupled to the bath in a spin-boson model. The populations of the two-level sub-system are taken as control objectives; namely, their revivals or exchange when switching off the field. We, in parallel, analyze how the optimal electric field consequently modifies the information back flow from the environment through different non-Markovian witnesses. Although the control field has a dipole interaction with the central sub-system only, its indirect influence on the bath collective mode dynamics is probed through HEOM auxiliary matrices, revealing a strong correlation between control and dissipation during a non-Markovian process. A heterojunction is taken as an illustrative example for modeling in a realistic way the two-level sub-system parameters and its spectral density function leading to a non-perturbative strong coupling regime with the bath. Although, due to strong system-bath couplings, control performances remain rather modest, the most important result is a noticeable increase of the non-Markovian bath response induced by the optimally driven processes.

Child maltreatment and trajectories of personality and behavioral functioning: Implications for the development of personality disorder

PubMed Central

Kim, Jungmeen; Cicchetti, Dante; Rogosch, Fred A.; Manly, Jody Todd

2009-01-01

This study investigated the longitudinal impact of maltreatment parameters on personality processes and maladjustment and prospective relationships between personality trajectory classes and subsequent maladjustment outcomes. The sample involved maltreated (n = 249) and nonmaltreated (n = 200) children followed longitudinally between ages 6 – 10. Growth mixture modeling indicated multifinality in personality development depending on the risk status (i.e., maltreated vs. nonmaltreated). Two trajectory classes of ego resiliency were identified for maltreated children; those who showed a declining trajectory exhibited greater maladjustment. In contrast, three trajectory classes of ego control were identified for nonmaltreated children; the subgroups showing increases in ego under-control or dramatic changes from high ego under-control to high ego over-control exhibited poor adjustment. Experiencing multiple maltreatment subtypes and physical/sexual abuse were related to higher levels of ego under-control and externalizing symptomatology, whereas early onset of maltreatment was associated with the low and decreasing trajectory of ego resiliency and higher levels of internalizing symptomatology. The findings suggest that ego resiliency and ego control – personality processes related to self-regulation – may be important factors in identifying distinct pathways to later personality disorders as well as pathways to resilient functioning. PMID:19583889

Flexible distributed architecture for semiconductor process control and experimentation

NASA Astrophysics Data System (ADS)

Gower, Aaron E.; Boning, Duane S.; McIlrath, Michael B.

1997-01-01

Semiconductor fabrication requires an increasingly expensive and integrated set of tightly controlled processes, driving the need for a fabrication facility with fully computerized, networked processing equipment. We describe an integrated, open system architecture enabling distributed experimentation and process control for plasma etching. The system was developed at MIT's Microsystems Technology Laboratories and employs in-situ CCD interferometry based analysis in the sensor-feedback control of an Applied Materials Precision 5000 Plasma Etcher (AME5000). Our system supports accelerated, advanced research involving feedback control algorithms, and includes a distributed interface that utilizes the internet to make these fabrication capabilities available to remote users. The system architecture is both distributed and modular: specific implementation of any one task does not restrict the implementation of another. The low level architectural components include a host controller that communicates with the AME5000 equipment via SECS-II, and a host controller for the acquisition and analysis of the CCD sensor images. A cell controller (CC) manages communications between these equipment and sensor controllers. The CC is also responsible for process control decisions; algorithmic controllers may be integrated locally or via remote communications. Finally, a system server images connections from internet/intranet (web) based clients and uses a direct link with the CC to access the system. Each component communicates via a predefined set of TCP/IP socket based messages. This flexible architecture makes integration easier and more robust, and enables separate software components to run on the same or different computers independent of hardware or software platform.

FAST TRACK COMMUNICATION: Controllable optical bistability and multistability in a double two-level atomic system

NASA Astrophysics Data System (ADS)

Wu, Jing; Lü, Xin-You; Zheng, Li-Li

2010-08-01

We theoretically investigate the behaviour of optical bistability (OB) and optical multistability (OM) in a generic double two-level atomic system driven by two orthogonally polarized fields (a π-polarized control field and a σ-polarized probe field). It is found that the behaviour of OB can be controlled by adjusting the intensity or the frequency detuning of the control field. Interestingly enough, our numerical results also show that it is easy to realize the transition from OB to OM or vice versa by adjusting the relative phase between the control and probe fields. This investigation can be used for the development of new types of devices for realizing an all-optic switching process.

Modification in oxidative processes in muscle tissues exposed to laser- and light-emitting diode radiation.

PubMed

Monich, Victor A; Bavrina, Anna P; Malinovskaya, Svetlana L

2018-01-01

Exposure of living tissues to high-intensity red or near-infrared light can produce the oxidative stress effects both in the target zone and adjacent ones. The protein oxidative modification (POM) products can be used as reliable and early markers of oxidative stress. The contents of modified proteins in the investigated specimens can be evaluated by the 2,4-dinitrophenylhydrazine assay (the DNPH assay). Low-intensity red light is able to decrease the activity of oxidative processes and the DNPH assay data about the POM products in the biological tissues could show both an oxidative stress level and an efficiency of physical agent protection against the oxidative processes. Two control groups of white rats were irradiated by laser light, the first control group by red light and the second one by near-infrared radiation (NIR).Two experimental groups were consequently treated with laser and red low-level light-emitting diode radiation (LED). One of them was exposed to red laser light + LED and the other to NIR + LED. The fifth group was intact. Each group included ten animals. The effect of laser light was studied by methods of protein oxidative modifications. We measured levels of both induced and spontaneous POM products by the DNPH assay. The dramatic increase in levels of POM products in the control group samples when compared with the intact group data as well as the sharp decrease in the POM products in the experimental groups treated with LED low-level light were statistically significant (p ≤ 0.05). Exposure of skeletal muscles to high-intensity red and near-infrared laser light causes oxidative stress that continues not less than 3 days. The method of measurement of POM product contents by the DNPH assay is a reliable test of an oxidative process rate. Red low-intensity LED radiation can provide rehabilitation of skeletal muscle tissues treated with high-intensity laser light.

Dimensions of control as related to work organization, stress, and health.

PubMed

Aronsson, G

1989-01-01

The aim of this article is to examine how increased worker control-on the individual as well as on collective level-may be a means to reduce the risk of work environment-related stress and diseases. Control is also an important element in socialization processes and in work reform activities directed to a democratization of working life. The concept of control connects a number of research perspectives. It deals with the individual and the collective level, as well as the relationship between them, and it may be a bridge between a social psychological and a psychobiological perspective. In this article, the author considers the control concept primarily from a stress perspective, but also examines how production techniques, legislation, and management strategies create the structure of control at work.

The fuzzy algorithm in the die casting mould for the application of multi-channel temperature control

NASA Astrophysics Data System (ADS)

Sun, Jin-gen; Chen, Yi; Zhang, Jia-nan

2017-01-01

Mould manufacturing is one of the most basic elements in the production chain of China. The mould manufacturing technology has become an important symbol to measure the level of a country's manufacturing industry. The die-casting mould multichannel intelligent temperature control method is studied by cooling water circulation, which uses fuzzy control to realize, aiming at solving the shortcomings of slow speed and big energy consumption during the cooling process of current die-casting mould. At present, the traditional PID control method is used to control the temperature, but it is difficult to ensure the control precision. While , the fuzzy algorithm is used to realize precise control of mould temperature in cooling process. The design is simple, fast response, strong anti-interference ability and good robustness. Simulation results show that the control method is completely feasible, which has higher control precision.

Beyond Perception: Musical Representation and On-Line Processing in Autism

ERIC Educational Resources Information Center

Heaton, Pamela; Williams, Kerry; Cummins, Omar; Happe, Francesca G. E.

2007-01-01

Whilst findings from experimental studies suggest that perceptual mechanisms underpinning musical cognition are preserved or enhanced in autism, little is known about how higher-level, structural aspects of music are processed. Twenty participants with autism, together with age and intelligence matched controls, completed a musical priming task in…

40 CFR 63.1013 - Sampling connection systems standards.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) National Emission Standards for Equipment Leaks-Control Level 1 § 63.1013 Sampling connection... container are not required to be collected or captured. (c) Equipment design and operation. Each closed... process fluid to a process; or (3) Be designed and operated to capture and transport all the purged...

Adopting Quality Assurance Technology in Customer-Vendor Relationships: A Case Study of How Interorganizational Relationships Influence the Process

NASA Astrophysics Data System (ADS)

Heeager, Lise Tordrup; Tjørnehøj, Gitte

Quality assurance technology is a formal control mechanism aiming at increasing the quality of the product exchanged between vendors and customers. Studies of the adoption of this technology in the field of system development rarely focus on the role of the relationship between the customer and vendor in the process. We have studied how the process of adopting quality assurance technology by a small Danish IT vendor developing pharmacy software for a customer in the public sector was influenced by the relationship with the customer. The case study showed that the adoption process was shaped to a high degree by the relationship and vice versa. The prior high level of trust and mutual knowledge helped the parties negotiate mutually feasible solutions throughout the adoption process. We thus advise enhancing trust-building processes to strengthen the relationships and to balance formal control and social control to increase the likelihood of a successful outcome of the adoption of quality assurance technology in a customer-vendor relationship.

Holocene sand shoals offshore of the Mississippi River delta plain

USGS Publications Warehouse

Penland, Shea; Suter, John R.; McBride, Randolph A.; Williams, S. Jeffress; Kindinger, Jack G.; Boyd, Ron

1989-01-01

Collectively, these sand shoals represent a large potential source of aggregate for shoreline restoration and erosion control as well as possible hard mineral resources. Scientifically, these shoals provide insight into the processes which control coastal evolution and shelf sand development under the condition of relative sea level rise.

Domain-Specific Control Mechanisms for Emotional and Nonemotional Conflict Processing

ERIC Educational Resources Information Center

Soutschek, Alexander; Schubert, Torsten

2013-01-01

Recent neuroimaging studies suggest that the human brain activates dissociable cognitive control networks in response to conflicts arising within the cognitive and the affective domain. The present study tested the hypothesis that nonemotional and emotional conflict regulation can also be dissociated on a functional level. For that purpose, we…

40 CFR 63.1032 - Sampling connection systems standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) [Reserved] (3) Be designed and operated to capture and transport all the purged process fluid to a control... (CONTINUED) National Emission Standards for Equipment Leaks-Control Level 2 Standards § 63.1032 Sampling... design and operation. Each closed-purge, closed-loop, or closed vent system as required in paragraph (b...

40 CFR 63.1032 - Sampling connection systems standards.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) [Reserved] (3) Be designed and operated to capture and transport all the purged process fluid to a control... (CONTINUED) National Emission Standards for Equipment Leaks-Control Level 2 Standards § 63.1032 Sampling... design and operation. Each closed-purge, closed-loop, or closed vent system as required in paragraph (b...

Effects of Teacher Controlled Segmented-Animation Presentation in Facilitating Learning

ERIC Educational Resources Information Center

Mohamad Ali, Ahmad Zamzuri

2010-01-01

The aim of this research was to study the effectiveness of teacher controlled segmented-animation presentation on learning achievement of students with lower level of prior knowledge. Segmented-animation and continuous-animation courseware showing cellular signal transmission process were developed for the research purpose. Pre-test and post-test…

Sigma metrics as a tool for evaluating the performance of internal quality control in a clinical chemistry laboratory

PubMed Central

Kumar, B. Vinodh; Mohan, Thuthi

2018-01-01

OBJECTIVE: Six Sigma is one of the most popular quality management system tools employed for process improvement. The Six Sigma methods are usually applied when the outcome of the process can be measured. This study was done to assess the performance of individual biochemical parameters on a Sigma Scale by calculating the sigma metrics for individual parameters and to follow the Westgard guidelines for appropriate Westgard rules and levels of internal quality control (IQC) that needs to be processed to improve target analyte performance based on the sigma metrics. MATERIALS AND METHODS: This is a retrospective study, and data required for the study were extracted between July 2015 and June 2016 from a Secondary Care Government Hospital, Chennai. The data obtained for the study are IQC - coefficient of variation percentage and External Quality Assurance Scheme (EQAS) - Bias% for 16 biochemical parameters. RESULTS: For the level 1 IQC, four analytes (alkaline phosphatase, magnesium, triglyceride, and high-density lipoprotein-cholesterol) showed an ideal performance of ≥6 sigma level, five analytes (urea, total bilirubin, albumin, cholesterol, and potassium) showed an average performance of <3 sigma level and for level 2 IQCs, same four analytes of level 1 showed a performance of ≥6 sigma level, and four analytes (urea, albumin, cholesterol, and potassium) showed an average performance of <3 sigma level. For all analytes <6 sigma level, the quality goal index (QGI) was <0.8 indicating the area requiring improvement to be imprecision except cholesterol whose QGI >1.2 indicated inaccuracy. CONCLUSION: This study shows that sigma metrics is a good quality tool to assess the analytical performance of a clinical chemistry laboratory. Thus, sigma metric analysis provides a benchmark for the laboratory to design a protocol for IQC, address poor assay performance, and assess the efficiency of existing laboratory processes. PMID:29692587

Defense Waste Processing Facility (DWPF) Viscosity Model: Revisions for Processing High TiO 2 Containing Glasses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jantzen, C. M.; Edwards, T. B.

Radioactive high-level waste (HLW) at the Savannah River Site (SRS) has successfully been vitrified into borosilicate glass in the Defense Waste Processing Facility (DWPF) since 1996. Vitrification requires stringent product/process (P/P) constraints since the glass cannot be reworked once it is poured into ten foot tall by two foot diameter canisters. A unique “feed forward” statistical process control (SPC) was developed for this control rather than statistical quality control (SQC). In SPC, the feed composition to the DWPF melter is controlled prior to vitrification. In SQC, the glass product would be sampled after it is vitrified. Individual glass property-composition modelsmore » form the basis for the “feed forward” SPC. The models transform constraints on the melt and glass properties into constraints on the feed composition going to the melter in order to guarantee, at the 95% confidence level, that the feed will be processable and that the durability of the resulting waste form will be acceptable to a geologic repository. The DWPF SPC system is known as the Product Composition Control System (PCCS). The DWPF will soon be receiving wastes from the Salt Waste Processing Facility (SWPF) containing increased concentrations of TiO 2, Na 2O, and Cs 2O . The SWPF is being built to pretreat the high-curie fraction of the salt waste to be removed from the HLW tanks in the F- and H-Area Tank Farms at the SRS. In order to process TiO 2 concentrations >2.0 wt% in the DWPF, new viscosity data were developed over the range of 1.90 to 6.09 wt% TiO 2 and evaluated against the 2005 viscosity model. An alternate viscosity model is also derived for potential future use, should the DWPF ever need to process other titanate-containing ion exchange materials. The ultimate limit on the amount of TiO 2 that can be accommodated from SWPF will be determined by the three PCCS models, the waste composition of a given sludge batch, the waste loading of the sludge batch, and the frit used for vitrification.« less

77 FR 16865 - Proposed Extension of Existing Information Collection; Occupational Noise Exposure

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-22

..., administrative controls, and personal protective equipment to protect miners from harmful levels of noise that..., compressors, conveyors, trucks, loaders, and other heavy-duty equipment for the excavation, haulage, and processing of material. This equipment creates high sound levels, exposing machine operators as well as...

A new flight control and management system architecture and configuration

NASA Astrophysics Data System (ADS)

Kong, Fan-e.; Chen, Zongji

2006-11-01

The advanced fighter should possess the performance such as super-sound cruising, stealth, agility, STOVL(Short Take-Off Vertical Landing),powerful communication and information processing. For this purpose, it is not enough only to improve the aerodynamic and propulsion system. More importantly, it is necessary to enhance the control system. A complete flight control system provides not only autopilot, auto-throttle and control augmentation, but also the given mission management. F-22 and JSF possess considerably outstanding flight control system on the basis of pave pillar and pave pace avionics architecture. But their control architecture is not enough integrated. The main purpose of this paper is to build a novel fighter control system architecture. The control system constructed on this architecture should be enough integrated, inexpensive, fault-tolerant, high safe, reliable and effective. And it will take charge of both the flight control and mission management. Starting from this purpose, this paper finishes the work as follows: First, based on the human nervous control, a three-leveled hierarchical control architecture is proposed. At the top of the architecture, decision level is in charge of decision-making works. In the middle, organization & coordination level will schedule resources, monitor the states of the fighter and switch the control modes etc. And the bottom is execution level which holds the concrete drive and measurement; then, according to their function and resources all the tasks involving flight control and mission management are sorted to individual level; at last, in order to validate the three-leveled architecture, a physical configuration is also showed. The configuration is distributed and applies some new advancement in information technology industry such line replaced module and cluster technology.

Splash, pop, sizzle: Information processing with phononic computing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sklan, Sophia R.

2015-05-15

Phonons, the quanta of mechanical vibration, are important to the transport of heat and sound in solid materials. Recent advances in the fundamental control of phonons (phononics) have brought into prominence the potential role of phonons in information processing. In this review, the many directions of realizing phononic computing and information processing are examined. Given the relative similarity of vibrational transport at different length scales, the related fields of acoustic, phononic, and thermal information processing are all included, as are quantum and classical computer implementations. Connections are made between the fundamental questions in phonon transport and phononic control and themore » device level approach to diodes, transistors, memory, and logic. .« less

Power processing for electric propulsion

NASA Technical Reports Server (NTRS)

Finke, R. C.; Herron, B. G.; Gant, G. D.

1975-01-01

The inclusion of electric thruster systems in spacecraft design is considered. The propulsion requirements of such spacecraft dictate a wide range of thruster power levels and operational lifetimes, which must be matched by lightweight, efficient, and reliable thruster power processing systems. Electron bombardment ion thruster requirements are presented, and the performance characteristics of present power processing systems are reviewed. Design philosophies and alternatives in areas such as inverter type, arc protection, and control methods are discussed along with future performance potentials for meeting goals in the areas of power process or weight (10 kg/kW), efficiency (approaching 92 percent), reliability (0.96 for 15,000 hr), and thermal control capability (0.3 to 5 AU).

Temperature control of power semiconductor devices in traction applications

NASA Astrophysics Data System (ADS)

Pugachev, A. A.; Strekalov, N. N.

2017-02-01

The peculiarity of thermal management of traction frequency converters of a railway rolling stock is highlighted. The topology and the operation principle of the automatic temperature control system of power semiconductor modules of the traction frequency converter are designed and discussed. The features of semiconductors as an object of temperature control are considered; the equivalent circuit of thermal processes in the semiconductors is suggested, the power losses in the two-level voltage source inverters are evaluated and analyzed. The dynamic properties and characteristics of the cooling fan induction motor electric drive with the scalar control are presented. The results of simulation in Matlab are shown for the steady state of thermal processes.

Food safety objective approach for controlling Clostridium botulinum growth and toxin production in commercially sterile foods.

PubMed

Anderson, N M; Larkin, J W; Cole, M B; Skinner, G E; Whiting, R C; Gorris, L G M; Rodriguez, A; Buchanan, R; Stewart, C M; Hanlin, J H; Keener, L; Hall, P A

2011-11-01

As existing technologies are refined and novel microbial inactivation technologies are developed, there is a growing need for a metric that can be used to judge equivalent levels of hazard control stringency to ensure food safety of commercially sterile foods. A food safety objective (FSO) is an output-oriented metric that designates the maximum level of a hazard (e.g., the pathogenic microorganism or toxin) tolerated in a food at the end of the food supply chain at the moment of consumption without specifying by which measures the hazard level is controlled. Using a risk-based approach, when the total outcome of controlling initial levels (H(0)), reducing levels (ΣR), and preventing an increase in levels (ΣI) is less than or equal to the target FSO, the product is considered safe. A cross-disciplinary international consortium of specialists from industry, academia, and government was organized with the objective of developing a document to illustrate the FSO approach for controlling Clostridium botulinum toxin in commercially sterile foods. This article outlines the general principles of an FSO risk management framework for controlling C. botulinum growth and toxin production in commercially sterile foods. Topics include historical approaches to establishing commercial sterility; a perspective on the establishment of an appropriate target FSO; a discussion of control of initial levels, reduction of levels, and prevention of an increase in levels of the hazard; and deterministic and stochastic examples that illustrate the impact that various control measure combinations have on the safety of well-established commercially sterile products and the ways in which variability all levels of control can heavily influence estimates in the FSO risk management framework. This risk-based framework should encourage development of innovative technologies that result in microbial safety levels equivalent to those achieved with traditional processing methods.

Elevated IL-8 levels during sickle cell crisis.

PubMed

Duits, A J; Schnog, J B; Lard, L R; Saleh, A W; Rojer, R A

1998-11-01

The vaso-occlusive process (VOC) in sickle cell disease is of a complex nature. It involves intricate interactions between sickle red blood cells, endothelium and probably also leukocytes. As these interactions are regulated by cytokines, we analyzed the role of the potent neutrophil chemokine IL-8 by measuring serum levels in sickle cell patients during sickle cell crisis. These results were compared to nonsymptomatics and healthy controls. In patients having a vaso-occlusive crisis both HbSS and HbSC patients showed significantly enhanced serum IL-8 levels compared to healthy controls. Several of these patients showed extremely elevated serum IL-8 levels which were independent of the crisis inducing factor. Furthermore, a sickle cell patient with VOC as a complication of rhGM-CSF treatment similarly showed high IL-8 serum levels at crisis onset. Nonsymptomatic sickle cell patients serum IL-8 levels were comparable to healthy controls. These results implicate a role for IL-8 at or during (the initiation of) sickle cell crisis.

Proceedings of the Symposium on Psychology in the Department of Defense (13th) Held in Colorado Springs, Colorado on 15-17 April 1992

DTIC Science & Technology

1992-04-17

decreased to roughly the level of the control group. This reduction holds for the remainder of the training program. Also important in these data was...the actual world results being modeled . Benefits of Applying the Conant-Ashby Theorem The primary problem associated with system (process) control is...rating of performance, and a rating of others’ performance, on ten-point Likert scales. 62 Results The data were analyzed at three levels :

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoshii, Kazutomo; Llopis, Pablo; Zhang, Kaicheng

As CMOS scaling nears its end, parameter variations (process, temperature and voltage) are becoming a major concern. To overcome parameter variations and provide stability, modern processors are becoming dynamic, opportunistically adjusting voltage and frequency based on thermal and energy constraints, which negatively impacts traditional bulk-synchronous parallelism-minded hardware and software designs. As node-level architecture is growing in complexity, implementing variation control mechanisms only with hardware can be a challenging task. In this paper we investigate a software strategy to manage hardwareinduced variations, leveraging low-level monitoring/controlling mechanisms.

Caribbean mangroves adjust to rising sea level through biotic controls on change in soil elevation

USGS Publications Warehouse

McKee, K.L.; Cahoon, D.R.; Feller, Ilka C.

2007-01-01

Aim The long-term stability of coastal ecosystems such as mangroves and salt marshes depends upon the maintenance of soil elevations within the intertidal habitat as sea level changes. We examined the rates and processes of peat formation by mangroves of the Caribbean Region to better understand biological controls on habitat stability. Location Mangrove-dominated islands on the Caribbean coasts of Belize, Honduras and Panama were selected as study sites. Methods Biological processes controlling mangrove peat formation were manipulated (in Belize) by the addition of nutrients (nitrogen or phosphorus) to Rhizophora mangle (red mangrove), and the effects on the dynamics of soil elevation were determined over a 3-year period using rod surface elevation tables (RSET) and marker horizons. Peat composition and geological accretion rates were determined at all sites using radiocarbon-dated cores. Results The addition of nutrients to mangroves caused significant changes in rates of mangrove root accumulation, which influenced both the rate and direction of change in elevation. Areas with low root input lost elevation and those with high rates gained elevation. These findings were consistent with peat analyses at multiple Caribbean sites showing that deposits (up to 10 m in depth) were composed primarily of mangrove root matter. Comparison of radiocarbon-dated cores at the study sites with a sea-level curve for the western Atlantic indicated a tight coupling between peat building in Caribbean mangroves and sea-level rise over the Holocene. Main conclusions Mangroves common to the Caribbean region have adjusted to changing sea level mainly through subsurface accumulation of refractory mangrove roots. Without root and other organic inputs, submergence of these tidal forests is inevitable due to peat decomposition, physical compaction and eustatic sea-level rise. These findings have relevance for predicting the effects of sea-level rise and biophysical processes on tropical mangrove ecosystems.

Active porous transition towards spatiotemporal control of molecular flow in a crystal membrane

NASA Astrophysics Data System (ADS)

Takasaki, Yuichi; Takamizawa, Satoshi

2015-11-01

Fluidic control is an essential technology widely found in processes such as flood control in land irrigation and cell metabolism in biological tissues. In any fluidic control system, valve function is the key mechanism used to actively regulate flow and miniaturization of fluidic regulation with precise workability will be particularly vital in the development of microfluidic control. The concept of crystal engineering is alternative to processing technology in microstructure construction, as the ultimate microfluidic devices must provide molecular level control. Consequently, microporous crystals can instantly be converted to microfluidic devices if introduced in an active transformability of porous structure and geometry. Here we show that the introduction of a stress-induced martensitic transition mechanism converts a microporous molecular crystal into an active fluidic device with spatiotemporal molecular flow controllability through mechanical reorientation of subnanometre channels.

Atypical vertical sound localization and sound-onset sensitivity in people with autism spectrum disorders.

PubMed

Visser, Eelke; Zwiers, Marcel P; Kan, Cornelis C; Hoekstra, Liesbeth; van Opstal, A John; Buitelaar, Jan K

2013-11-01

Autism spectrum disorders (ASDs) are associated with auditory hyper- or hyposensitivity; atypicalities in central auditory processes, such as speech-processing and selective auditory attention; and neural connectivity deficits. We sought to investigate whether the low-level integrative processes underlying sound localization and spatial discrimination are affected in ASDs. We performed 3 behavioural experiments to probe different connecting neural pathways: 1) horizontal and vertical localization of auditory stimuli in a noisy background, 2) vertical localization of repetitive frequency sweeps and 3) discrimination of horizontally separated sound stimuli with a short onset difference (precedence effect). Ten adult participants with ASDs and 10 healthy control listeners participated in experiments 1 and 3; sample sizes for experiment 2 were 18 adults with ASDs and 19 controls. Horizontal localization was unaffected, but vertical localization performance was significantly worse in participants with ASDs. The temporal window for the precedence effect was shorter in participants with ASDs than in controls. The study was performed with adult participants and hence does not provide insight into the developmental aspects of auditory processing in individuals with ASDs. Changes in low-level auditory processing could underlie degraded performance in vertical localization, which would be in agreement with recently reported changes in the neuroanatomy of the auditory brainstem in individuals with ASDs. The results are further discussed in the context of theories about abnormal brain connectivity in individuals with ASDs.

Contamination control engineering design guidelines for the aerospace community

NASA Technical Reports Server (NTRS)

Tribble, A. C. (Principal Investigator); Boyadjian, B.; Davis, J.; Haffner, J.; McCullough, E.

1996-01-01

Thermal control surfaces, solar arrays, and optical devices may be adversely affected by a small quantity of molecular and/or particulate contamination. What is rarely discussed is how one: (1) quantifies the level of contamination that must be maintained in order for the system to function properly, and (2) enforces contamination control to ensure compliance with requirements. This document is designed to address these specific issues and is intended to serve as a handbook on contamination control for the reader, illustrating process and methodology while providing direction to more detailed references when needed. The effects of molecular contamination on reflecting and transmitting surfaces are examined and quantified in accordance with MIL STD 1246C. The generation, transportation, and deposition of molecular contamination is reviewed and specific examples are worked to illustrate the process a design engineer can use to estimate end of life cleanliness levels required by solar arrays, thermal control surfaces, and optical surfaces. A similar process is used to describe the effect of particulate contamination as related to percent area coverage (PAC) and bi-directional reflectance distribution function (BRDF). Relationships between PAC and surface cleanliness, which include the effects of submicron sized particles, are developed and BRDF is related to specific sensor design parameters such as Point Source Transmittance (PST). The pros and cons of various methods of preventing, monitoring, and cleaning surfaces are examined and discussed.

Ultra-accelerated natural sunlight exposure testing

DOEpatents

Jorgensen, Gary J.; Bingham, Carl; Goggin, Rita; Lewandowski, Allan A.; Netter, Judy C.

2000-06-13

Process and apparatus for providing ultra accelerated natural sunlight exposure testing of samples under controlled weathering without introducing unrealistic failure mechanisms in exposed materials and without breaking reciprocity relationships between flux exposure levels and cumulative dose that includes multiple concurrent levels of temperature and relative humidity at high levels of natural sunlight comprising: a) concentrating solar flux uniformly; b) directing the controlled uniform sunlight onto sample materials in a chamber enclosing multiple concurrent levels of temperature and relative humidity to allow the sample materials to be subjected to accelerated irradiance exposure factors for a sufficient period of time in days to provide a corresponding time of about at least a years worth of representative weathering of the sample materials.

Financial Incentives for Chronic Disease Management: Results and Limitations of 2 Randomized Clinical Trials With New York Medicaid Patients.

PubMed

VanEpps, Eric M; Troxel, Andrea B; Villamil, Elizabeth; Saulsgiver, Kathryn A; Zhu, Jingsan; Chin, Jo-Yu; Matson, Jacqueline; Anarella, Joseph; Roohan, Patrick; Gesten, Foster; Volpp, Kevin G

2018-01-01

To identify whether financial incentives promote improved disease management in Medicaid recipients diagnosed with hypertension or diabetes, respectively. Four-group, multicenter, randomized clinical trials. Between 2013 and 2016, New York State Medicaid managed care members diagnosed with hypertension (N = 920) or with diabetes (N = 959). Participants in each 6-month trial were randomly assigned to 1 of 4 arms: (1) process incentives-earned by attending primary care visits and/or receiving prescription medication refills, (2) outcome incentives-earned by reducing systolic blood pressure (hypertension) or hemoglobin A 1c (HbA 1c ; diabetes) levels, (3) combined process and outcome incentives, and (4) control (no incentives). Systolic blood pressure (hypertension) and HbA 1c (diabetes) levels, primary care visits, and medication prescription refills. Analysis and Results: At 6 months, there were no statistically significant differences between intervention arms and the control arm in the change in systolic blood pressure, P = .531. Similarly, there were no significant differences in blood glucose control (HbA 1c ) between the intervention arms and control after 6 months, P = .939. The majority of participants had acceptable systolic blood pressure (<140 mm Hg) or blood glucose (<8.0%) levels at baseline and throughout the study. Financial incentives-regardless of whether they were delivered based on disease-relevant outcomes, process activities, or a combination of the two-have a negligible impact on health outcomes for Medicaid recipients diagnosed with either hypertension or diabetes in 2 studies in which, among other design and operational limitations, the majority of recipients had relatively well-controlled diseases at the time of enrollment.

Information modeling system for blast furnace control

NASA Astrophysics Data System (ADS)

Spirin, N. A.; Gileva, L. Y.; Lavrov, V. V.

2016-09-01

Modern Iron & Steel Works as a rule are equipped with powerful distributed control systems (DCS) and databases. Implementation of DSC system solves the problem of storage, control, protection, entry, editing and retrieving of information as well as generation of required reporting data. The most advanced and promising approach is to use decision support information technologies based on a complex of mathematical models. The model decision support system for control of blast furnace smelting is designed and operated. The basis of the model system is a complex of mathematical models created using the principle of natural mathematical modeling. This principle provides for construction of mathematical models of two levels. The first level model is a basic state model which makes it possible to assess the vector of system parameters using field data and blast furnace operation results. It is also used to calculate the adjustment (adaptation) coefficients of the predictive block of the system. The second-level model is a predictive model designed to assess the design parameters of the blast furnace process when there are changes in melting conditions relative to its current state. Tasks for which software is developed are described. Characteristics of the main subsystems of the blast furnace process as an object of modeling and control - thermal state of the furnace, blast, gas dynamic and slag conditions of blast furnace smelting - are presented.

Intensive lifestyle intervention provides rapid reduction of serum fatty acid levels in women with severe obesity without lowering omega-3 to unhealthy levels.

PubMed

Lin, C; Andersen, J R; Våge, V; Rajalahti, T; Mjøs, S A; Kvalheim, O M

2016-08-01

Serum fatty acid (FA) levels were monitored in women with severe obesity during intensive lifestyle intervention. At baseline, total FA levels and most individual FAs were elevated compared to a matching cohort of normal and overweight women (healthy controls). After 3 weeks of intensive lifestyle intervention, total level was only 11-12% higher than in the healthy controls and with almost all FAs being significantly lower than at baseline, but with levels of omega-3 being similar to the healthy controls. This is contrary to observations for patients subjected to bariatric surgery where omega-3 levels dropped to levels significantly lower than in the lifestyle patients and healthy controls. During the next 3 weeks of treatment, the FA levels in lifestyle patients were unchanged, while the weight loss continued at almost the same rate as in the first 3 weeks. Multivariate analysis revealed that weight loss and change of serum FA patterns were unrelated outcomes of the intervention for lifestyle patients. For bariatric patients, these processes were associated probably due to reduced dietary input and increased input from the patients' own fat deposits, causing a higher rate of weight loss and simultaneous reduction of the ratio of serum eicosapentaenoic to arachidonic acid. © 2016 World Obesity.

Reevaluation of the non-lesional dry skin in atopic dermatitis by acute barrier disruption: an abnormal permeability barrier homeostasis with defective processing to generate ceramide.

PubMed

Sugiura, Ayumi; Nomura, Tsuyoshi; Mizuno, Atsuko; Imokawa, Genji

2014-07-01

Atopic dermatitis is characterized by disruption of the cutaneous barrier due to reduced ceramide levels even in non-lesional dry skin. Following further acute barrier disruption by repeated tape strippings, we re-characterized the non-lesional dry skin of subjects with atopic dermatitis, which shows significantly reduced levels of barrier function and ceramide but not of beta-glucocerebrosidase activity. For the first time, we report an abnormal trans-epidermal water loss homeostasis in which delayed recovery kinetics of trans-epidermal water loss occurred on the first day during the 4 days after acute barrier disruption compared with healthy control skin. Interestingly, whereas the higher ceramide level in the stratum corneum of healthy control skin was further significantly up-regulated at 4 days post-tape stripping, the lower ceramide level in the stratum corneum of subjects with atopic dermatitis was not significantly changed. In a parallel study, whereas beta-glucocerebrosidase activity at 4 days post-tape stripping was significantly up-regulated in healthy control skin compared with before tape stripping, the level of that activity remained substantially unchanged in atopic dermatitis. These findings indicate that subjects with atopic dermatitis have a defect in sphingolipid-metabolic processing that generates ceramide in the interface between the stratum corneum and the epidermis. The results also support the notion that the continued disruption of barrier function in atopic dermatitis non-lesional skin is associated with the impaired homeostasis of a ceramide-generating process, which underscores an atopy-specific inflammation-triggered ceramide deficiency that is distinct from other types of dermatitis.

Interindividual differences in stress sensitivity: basal and stress-induced cortisol levels differentially predict neural vigilance processing under stress

PubMed Central

Klumpers, Floris; Everaerd, Daphne; Kooijman, Sabine C.; van Wingen, Guido A.; Fernández, Guillén

2016-01-01

Stress exposure is known to precipitate psychological disorders. However, large differences exist in how individuals respond to stressful situations. A major marker for stress sensitivity is hypothalamus–pituitary–adrenal (HPA)-axis function. Here, we studied how interindividual variance in both basal cortisol levels and stress-induced cortisol responses predicts differences in neural vigilance processing during stress exposure. Implementing a randomized, counterbalanced, crossover design, 120 healthy male participants were exposed to a stress-induction and control procedure, followed by an emotional perception task (viewing fearful and happy faces) during fMRI scanning. Stress sensitivity was assessed using physiological (salivary cortisol levels) and psychological measures (trait questionnaires). High stress-induced cortisol responses were associated with increased stress sensitivity as assessed by psychological questionnaires, a stronger stress-induced increase in medial temporal activity and greater differential amygdala responses to fearful as opposed to happy faces under control conditions. In contrast, high basal cortisol levels were related to relative stress resilience as reflected by higher extraversion scores, a lower stress-induced increase in amygdala activity and enhanced differential processing of fearful compared with happy faces under stress. These findings seem to reflect a critical role for HPA-axis signaling in stress coping; higher basal levels indicate stress resilience, whereas higher cortisol responsivity to stress might facilitate recovery in those individuals prone to react sensitively to stress. PMID:26668010

[Quality process control system of Chinese medicine preparation based on "holistic view"].

PubMed

Wang, Ya-Qi; Jiao, Jiao-Jiao; Wu, Zhen-Feng; Zheng, Qin; Yang, Ming

2018-01-01

"High quality, safety and effectiveness" are the primary principles for the pharmaceutical research and development process in China. The quality of products relies not only on the inspection method, but also on the design and development, process control and standardized management. The quality depends on the process control level. In this paper, the history and current development of quality control of traditional Chinese medicine (TCM) preparations are reviewed systematically. Based on the development model of international drug quality control and the misunderstanding of quality control of TCM preparations, the reasons for impacting the homogeneity of TCM preparations are analyzed and summarized. According to TCM characteristics, efforts were made to control the diversity of TCM, make "unstable" TCM into "stable" Chinese patent medicines, put forward the concepts of "holistic view" and "QbD (quality by design)", so as to create the "holistic, modular, data, standardized" model as the core of TCM preparation quality process control model. Scientific studies shall conform to the actual production of TCM preparations, and be conducive to supporting advanced equipment and technology upgrade, thoroughly applying the scientific research achievements in Chinese patent medicines, and promoting the cluster application and transformation application of TCM pharmaceutical technology, so as to improve the quality and effectiveness of the TCM industry and realize the green development. Copyright© by the Chinese Pharmaceutical Association.

Modelling aspects regarding the control in 13C isotope separation column

NASA Astrophysics Data System (ADS)

Boca, M. L.

2016-08-01

Carbon represents the fourth most abundant chemical element in the world, having two stable and one radioactive isotope. The 13Carbon isotopes, with a natural abundance of 1.1%, plays an important role in numerous applications, such as the study of human metabolism changes, molecular structure studies, non-invasive respiratory tests, Alzheimer tests, air pollution and global warming effects on plants [9] A manufacturing control system manages the internal logistics in a production system and determines the routings of product instances, the assignment of workers and components, the starting of the processes on not-yet-finished product instances. Manufacturing control does not control the manufacturing processes themselves, but has to cope with the consequences of the processing results (e.g. the routing of products to a repair station). In this research it was fulfilled some UML (Unified Modelling Language) diagrams for modelling the C13 Isotope Separation column, implement in STARUML program. Being a critical process and needing a good control and supervising, the critical parameters in the column, temperature and pressure was control using some PLC (Programmable logic controller) and it was made some graphic analyze for this to observe some critical situation than can affect the separation process. The main parameters that need to be control are: -The liquid nitrogen (N2) level in the condenser. -The electrical power supplied to the boiler. -The vacuum pressure.

Experimental Design For Photoresist Characterization

NASA Astrophysics Data System (ADS)

Luckock, Larry

1987-04-01

In processing a semiconductor product (from discrete devices up to the most complex products produced) we find more photolithographic steps in wafer fabrication than any other kind of process step. Thus, the success of a semiconductor manufacturer hinges on the optimization of their photolithographic processes. Yet, we find few companies that have taken the time to properly characterize this critical operation; they are sitting in the "passenger's seat", waiting to see what will come out, hoping that the yields will improve someday. There is no "black magic" involved in setting up a process at its optimum conditions (i.e. minimum sensitivity to all variables at the same time). This paper gives an example of a real world situation for optimizing a photolithographic process by the use of a properly designed experiment, followed by adequate multidimensional analysis of the data. Basic SPC practices like plotting control charts will not, by themselves, improve yields; the control charts are, however, among the necessary tools used in the determination of the process capability and in the formulation of the problems to be addressed. The example we shall consider is the twofold objective of shifting the process average, while tightening the variance, of polysilicon line widths. This goal was identified from a Pareto analysis of yield-limiting mechanisms, plus inspection of the control charts. A key issue in a characterization of this type of process is the number of interactions between variables; this example rules out two-level full factorial and three-level fractional factorial designs (which cannot detect all of the interactions). We arrive at an experiment with five factors at five levels each. A full factorial design for five factors at three levels would require 3125 wafers. Instead, we will use a design that allows us to run this experiment with only 25 wafers, for a significant reduction in time, materials and manufacturing interruption in order to complete the experiment. An optimum solution is then determined via response surface analysis and a series of 3-D and contour plots are shown. The offset between the mask dimensions and poly CD at the optimum operating conditions is discussed with respect to yield, profits and return-on-investment. The expert system used for process optimization covers all types of process steps, producing the best custom designed experiment based on the actual equipment used. The knowledge base contains parameter lists, by machine make and model, ranked by sensitivity and controllability. One option allows 3-D spatial characterization of equipment. For the purpose of this presentation, we will assume that we want to optimize a photo-lithographic process used for polysilicon pattern definition and that we have determined minimum and maximum line widths, based on electrical yield requirements of the product. For this MOS process, the minimum critical dimension (CD) for the poly gate was determined by punchthrough voltage, threshold voltage, etc., while the maximum CD was determined from other performance factors like access time. We will start with the product engineer's analysis.