Using Statistical Process Control to Make Data-Based Clinical Decisions.

ERIC Educational Resources Information Center

Pfadt, Al; Wheeler, Donald J.

1995-01-01

Statistical process control (SPC), which employs simple statistical tools and problem-solving techniques such as histograms, control charts, flow charts, and Pareto charts to implement continual product improvement procedures, can be incorporated into human service organizations. Examples illustrate use of SPC procedures to analyze behavioral data…

Operational Control Procedures for the Activated Sludge Process, Part I - Observations, Part II - Control Tests.

ERIC Educational Resources Information Center

West, Alfred W.

This is the first in a series of documents developed by the National Training and Operational Technology Center describing operational control procedures for the activated sludge process used in wastewater treatment. Part I of this document deals with physical observations which should be performed during each routine control test. Part II…

Robot welding process control

NASA Technical Reports Server (NTRS)

Romine, Peter L.

1991-01-01

This final report documents the development and installation of software and hardware for Robotic Welding Process Control. Primary emphasis is on serial communications between the CYRO 750 robotic welder, Heurikon minicomputer running Hunter & Ready VRTX, and an IBM PC/AT, for offline programming and control and closed-loop welding control. The requirements for completion of the implementation of the Rocketdyne weld tracking control are discussed. The procedure for downloading programs from the Intergraph, over the network, is discussed. Conclusions are made on the results of this task, and recommendations are made for efficient implementation of communications, weld process control development, and advanced process control procedures using the Heurikon.

Preference for Modes of Dispute Resolution as a Function of Process and Decision Control

ERIC Educational Resources Information Center

Houlden, Pauline; And Others

1978-01-01

Research on procedural justice has suggested that the distribution of control among participants can be used to classify dispute-resolution procedures and may be an important determinant of preference for such procedures. This experiment demonstrates that control can be meaningfully divided into two components: control over the presentation of…

Standard Reference Specimens in Quality Control of Engineering Surfaces

PubMed Central

Song, J. F.; Vorburger, T. V.

1991-01-01

In the quality control of engineering surfaces, we aim to understand and maintain a good relationship between the manufacturing process and surface function. This is achieved by controlling the surface texture. The control process involves: 1) learning the functional parameters and their control values through controlled experiments or through a long history of production and use; 2) maintaining high accuracy and reproducibility with measurements not only of roughness calibration specimens but also of real engineering parts. In this paper, the characteristics, utilizations, and limitations of different classes of precision roughness calibration specimens are described. A measuring procedure of engineering surfaces, based on the calibration procedure of roughness specimens at NIST, is proposed. This procedure involves utilization of check specimens with waveform, wavelength, and other roughness parameters similar to functioning engineering surfaces. These check specimens would be certified under standardized reference measuring conditions, or by a reference instrument, and could be used for overall checking of the measuring procedure and for maintaining accuracy and agreement in engineering surface measurement. The concept of “surface texture design” is also suggested, which involves designing the engineering surface texture, the manufacturing process, and the quality control procedure to meet the optimal functional needs. PMID:28184115

[Design of an HACCP program for a cocoa processing facility].

PubMed

López D'Sola, Patrizia; Sandia, María Gabriela; Bou Rached, Lizet; Hernández Serrano, Pilar

2012-12-01

The HACCP plan is a food safety management tool used to control physical, chemical and biological hazards associated to food processing through all the processing chain. The aim of this work is to design a HACCP Plan for a Venezuelan cocoa processing facility.The production of safe food products requires that the HACCP system be built upon a solid foundation of prerequisite programs such as Good Manufacturing Practices (GMP) and Sanitation Standard Operating Procedures (SSOP). The existence and effectiveness of these prerequisite programs were previously assessed.Good Agriculture Practices (GAP) audit to cocoa nibs suppliers were performed. To develop the HACCP plan, the five preliminary tasks and the seven HACCP principles were accomplished according to Codex Alimentarius procedures. Three Critical Control Points (CCP) were identified using a decision tree: winnowing (control of ochratoxin A), roasting (Salmonella control) and metallic particles detection. For each CCP, Critical limits were established, the Monitoring procedures, Corrective actions, Procedures for Verification and Documentation concerning all procedures and records appropriate to these principles and their application was established. To implement and maintain a HACCP plan for this processing plant is suggested. Recently OchratoxinA (OTA) has been related to cocoa beans. Although the shell separation from the nib has been reported as an effective measure to control this chemical hazard, ochratoxin prevalence study in cocoa beans produced in the country is recommended, and validate the winnowing step as well

An NCME Instructional Module on Quality Control Procedures in the Scoring, Equating, and Reporting of Test Scores

ERIC Educational Resources Information Center

Allalouf, Avi

2007-01-01

There is significant potential for error in long production processes that consist of sequential stages, each of which is heavily dependent on the previous stage, such as the SER (Scoring, Equating, and Reporting) process. Quality control procedures are required in order to monitor this process and to reduce the number of mistakes to a minimum. In…

12 CFR 225.43 - Procedures for filing, processing, publishing, and acting on notices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Procedures for filing, processing, publishing... (REGULATION Y) Regulations Change in Bank Control § 225.43 Procedures for filing, processing, publishing, and.... Any person(s) filing a notice under this subpart shall publish, in a form prescribed by the Board, an...

Increasingly automated procedure acquisition in dynamic systems

NASA Technical Reports Server (NTRS)

Mathe, Nathalie; Kedar, Smadar

1992-01-01

Procedures are widely used by operators for controlling complex dynamic systems. Currently, most development of such procedures is done manually, consuming a large amount of paper, time, and manpower in the process. While automated knowledge acquisition is an active field of research, not much attention has been paid to the problem of computer-assisted acquisition and refinement of complex procedures for dynamic systems. The Procedure Acquisition for Reactive Control Assistant (PARC), which is designed to assist users in more systematically and automatically encoding and refining complex procedures. PARC is able to elicit knowledge interactively from the user during operation of the dynamic system. We categorize procedure refinement into two stages: diagnosis - diagnose the failure and choose a repair - and repair - plan and perform the repair. The basic approach taken in PARC is to assist the user in all steps of this process by providing increased levels of assistance with layered tools. We illustrate the operation of PARC in refining procedures for the control of a robot arm.

SEPAC software configuration control plan and procedures, revision 1

NASA Technical Reports Server (NTRS)

1981-01-01

SEPAC Software Configuration Control Plan and Procedures are presented. The objective of the software configuration control is to establish the process for maintaining configuration control of the SEPAC software beginning with the baselining of SEPAC Flight Software Version 1 and encompass the integration and verification tests through Spacelab Level IV Integration. They are designed to provide a simplified but complete configuration control process. The intent is to require a minimum amount of paperwork but provide total traceability of SEPAC software.

TU-FG-201-12: Designing a Risk-Based Quality Assurance Program for a Newly Implemented Y-90 Microspheres Procedure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vile, D; Zhang, L; Cuttino, L

2016-06-15

Purpose: To create a quality assurance program based upon a risk-based assessment of a newly implemented SirSpheres Y-90 procedure. Methods: A process map was created for a newly implemented SirSpheres procedure at a community hospital. The process map documented each step of this collaborative procedure, as well as the roles and responsibilities of each member. From the process map, different potential failure modes were determined as well as any current controls in place. From this list, a full failure mode and effects analysis (FMEA) was performed by grading each failure mode’s likelihood of occurrence, likelihood of detection, and potential severity.more » These numbers were then multiplied to compute the risk priority number (RPN) for each potential failure mode. Failure modes were then ranked based on their RPN. Additional controls were then added, with failure modes corresponding to the highest RPNs taking priority. Results: A process map was created that succinctly outlined each step in the SirSpheres procedure in its current implementation. From this, 72 potential failure modes were identified and ranked according to their associated RPN. Quality assurance controls and safety barriers were then added for failure modes associated with the highest risk being addressed first. Conclusion: A quality assurance program was created from a risk-based assessment of the SirSpheres process. Process mapping and FMEA were effective in identifying potential high-risk failure modes for this new procedure, which were prioritized for new quality assurance controls. TG 100 recommends the fault tree analysis methodology to design a comprehensive and effective QC/QM program, yet we found that by simply introducing additional safety barriers to address high RPN failure modes makes the whole process simpler and safer.« less

Combining principles of Cognitive Load Theory and diagnostic error analysis for designing job aids: Effects on motivation and diagnostic performance in a process control task.

PubMed

Kluge, Annette; Grauel, Britta; Burkolter, Dina

2013-03-01

Two studies are presented in which the design of a procedural aid and the impact of an additional decision aid for process control were assessed. In Study 1, a procedural aid was developed that avoids imposing unnecessary extraneous cognitive load on novices when controlling a complex technical system. This newly designed procedural aid positively affected germane load, attention, satisfaction, motivation, knowledge acquisition and diagnostic speed for novel faults. In Study 2, the effect of a decision aid for use before the procedural aid was investigated, which was developed based on an analysis of diagnostic errors committed in Study 1. Results showed that novices were able to diagnose both novel faults and practised faults, and were even faster at diagnosing novel faults. This research contributes to the question of how to optimally support novices in dealing with technical faults in process control. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

40 CFR 68.69 - Operating procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) CHEMICAL ACCIDENT PREVENTION PROVISIONS Program 3 Prevention Program § 68.69 Operating procedures. (a) The... presented by, the chemicals used in the process; (ii) Precautions necessary to prevent exposure, including engineering controls, administrative controls, and personal protective equipment; (iii) Control measures to be...

40 CFR 68.69 - Operating procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) CHEMICAL ACCIDENT PREVENTION PROVISIONS Program 3 Prevention Program § 68.69 Operating procedures. (a) The... presented by, the chemicals used in the process; (ii) Precautions necessary to prevent exposure, including engineering controls, administrative controls, and personal protective equipment; (iii) Control measures to be...

40 CFR 68.69 - Operating procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) CHEMICAL ACCIDENT PREVENTION PROVISIONS Program 3 Prevention Program § 68.69 Operating procedures. (a) The... presented by, the chemicals used in the process; (ii) Precautions necessary to prevent exposure, including engineering controls, administrative controls, and personal protective equipment; (iii) Control measures to be...

40 CFR 68.69 - Operating procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) CHEMICAL ACCIDENT PREVENTION PROVISIONS Program 3 Prevention Program § 68.69 Operating procedures. (a) The... presented by, the chemicals used in the process; (ii) Precautions necessary to prevent exposure, including engineering controls, administrative controls, and personal protective equipment; (iii) Control measures to be...

40 CFR 68.69 - Operating procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) CHEMICAL ACCIDENT PREVENTION PROVISIONS Program 3 Prevention Program § 68.69 Operating procedures. (a) The... presented by, the chemicals used in the process; (ii) Precautions necessary to prevent exposure, including engineering controls, administrative controls, and personal protective equipment; (iii) Control measures to be...

Automatic sample changer control software for automation of neutron activation analysis process in Malaysian Nuclear Agency

NASA Astrophysics Data System (ADS)

Yussup, N.; Ibrahim, M. M.; Rahman, N. A. A.; Mokhtar, M.; Salim, N. A. A.; Soh@Shaari, S. C.; Azman, A.; Lombigit, L.; Azman, A.; Omar, S. A.

2018-01-01

Most of the procedures in neutron activation analysis (NAA) process that has been established in Malaysian Nuclear Agency (Nuclear Malaysia) since 1980s were performed manually. These manual procedures carried out by the NAA laboratory personnel are time consuming and inefficient especially for sample counting and measurement process. The sample needs to be changed and the measurement software needs to be setup for every one hour counting time. Both of these procedures are performed manually for every sample. Hence, an automatic sample changer system (ASC) that consists of hardware and software is developed to automate sample counting process for up to 30 samples consecutively. This paper describes the ASC control software for NAA process which is designed and developed to control the ASC hardware and call GammaVision software for sample measurement. The software is developed by using National Instrument LabVIEW development package.

17 CFR 240.13a-15 - Controls and procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... based must be a suitable, recognized control framework that is established by a body or group that has..., without limitation, controls and procedures designed to ensure that information required to be disclosed... disclosure. (f) The term internal control over financial reporting is defined as a process designed by, or...

17 CFR 240.13a-15 - Controls and procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... based must be a suitable, recognized control framework that is established by a body or group that has..., without limitation, controls and procedures designed to ensure that information required to be disclosed... disclosure. (f) The term internal control over financial reporting is defined as a process designed by, or...

Analysis of Memory Formation during General Anesthesia (Propofol/Remifentanil) for Elective Surgery Using the Process-dissociation Procedure.

PubMed

Hadzidiakos, Daniel; Horn, Nadja; Degener, Roland; Buchner, Axel; Rehberg, Benno

2009-08-01

There have been reports of memory formation during general anesthesia. The process-dissociation procedure has been used to determine if these are controlled (explicit/conscious) or automatic (implicit/unconscious) memories. This study used the process-dissociation procedure with the original measurement model and one which corrected for guessing to determine if more accurate results were obtained in this setting. A total of 160 patients scheduled for elective surgery were enrolled. Memory for words presented during propofol and remifentanil general anesthesia was tested postoperatively by using a word-stem completion task in a process-dissociation procedure. To assign possible memory effects to different levels of anesthetic depth, the authors measured depth of anesthesia using the BIS XP monitor (Aspect Medical Systems, Norwood, MA). Word-stem completion performance showed no evidence of memory for intraoperatively presented words. Nevertheless, an evaluation of these data using the original measurement model for process-dissociation data suggested an evidence of controlled (C = 0.05; 95% confidence interval [CI] 0.02-0.08) and automatic (A = 0.11; 95% CI 0.09-0.12) memory processes (P < 0.01). However, when the data were evaluated with an extended measurement model taking base rates into account adequately, no evidence for controlled (C = 0.00; 95% CI -0.04 to 0.04) or automatic (A = 0.00; 95% CI -0.02 to 0.02) memory processes was obtained. The authors report and discuss parallel findings for published data sets that were generated by using the process-dissociation procedure. Patients had no memories for auditory information presented during propofol/remifentanil anesthesia after midazolam premedication. The use of the process-dissociation procedure with the original measurement model erroneously detected memories, whereas the extended model, corrected for guessing, correctly revealed no memory.

21 CFR 211.113 - Control of microbiological contamination.

Code of Federal Regulations, 2011 CFR

2011-04-01

... shall include validation of all aseptic and sterilization processes. [43 FR 45077, Sept. 29, 1978, as... Process Controls § 211.113 Control of microbiological contamination. (a) Appropriate written procedures...

21 CFR 211.113 - Control of microbiological contamination.

Code of Federal Regulations, 2012 CFR

2012-04-01

... shall include validation of all aseptic and sterilization processes. [43 FR 45077, Sept. 29, 1978, as... Process Controls § 211.113 Control of microbiological contamination. (a) Appropriate written procedures...

21 CFR 211.113 - Control of microbiological contamination.

Code of Federal Regulations, 2014 CFR

2014-04-01

... shall include validation of all aseptic and sterilization processes. [43 FR 45077, Sept. 29, 1978, as... Process Controls § 211.113 Control of microbiological contamination. (a) Appropriate written procedures...

21 CFR 211.113 - Control of microbiological contamination.

Code of Federal Regulations, 2013 CFR

2013-04-01

... shall include validation of all aseptic and sterilization processes. [43 FR 45077, Sept. 29, 1978, as... Process Controls § 211.113 Control of microbiological contamination. (a) Appropriate written procedures...

Serials Control System Procedures and Policies.

ERIC Educational Resources Information Center

Schlembach, Mary C.

This document includes procedures and policies for a networked serials control system originally developed at the Grainger Engineering Library Information Center at the University of Illinois at Urbana-Champaign (UIUC). The serials control systems encompass serials processing, public service, and end-user functions. The system employs a…

21 CFR 111.103 - What are the requirements under this subpart F for written procedures?

Code of Federal Regulations, 2010 CFR

2010-04-01

... MANUFACTURING, PACKAGING, LABELING, OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control... quality control operations, including written procedures for conducting a material review and making a...

Model prototype utilization in the analysis of fault tolerant control and data processing systems

NASA Astrophysics Data System (ADS)

Kovalev, I. V.; Tsarev, R. Yu; Gruzenkin, D. V.; Prokopenko, A. V.; Knyazkov, A. N.; Laptenok, V. D.

2016-04-01

The procedure assessing the profit of control and data processing system implementation is presented in the paper. The reasonability of model prototype creation and analysis results from the implementing of the approach of fault tolerance provision through the inclusion of structural and software assessment redundancy. The developed procedure allows finding the best ratio between the development cost and the analysis of model prototype and earnings from the results of this utilization and information produced. The suggested approach has been illustrated by the model example of profit assessment and analysis of control and data processing system.

Importance of good manufacturing practices in microbiological monitoring in processing human tissues for transplant.

PubMed

Pianigiani, Elisa; Ierardi, Francesca; Fimiani, Michele

2013-12-01

Skin allografts represent an important therapeutic resource in the treatment of severe skin loss. The risk associated with application of processed tissues in humans is very low, however, human material always carries the risk of disease transmission. To minimise the risk of contamination of grafts, processing is carried out in clean rooms where air quality is monitored. Procedures and quality control tests are performed to standardise the production process and to guarantee the final product for human use. Since we only validate and distribute aseptic tissues, we conducted a study to determine what type of quality controls for skin processing are the most suitable for detecting processing errors and intercurrent contamination, and for faithfully mapping the process without unduly increasing production costs. Two different methods for quality control were statistically compared using the Fisher exact test. On the basis of the current study we selected our quality control procedure based on pre- and post-processing tissue controls, operator and environmental controls. Evaluation of the predictability of our control methods showed that tissue control was the most reliable method of revealing microbial contamination of grafts. We obtained 100 % sensitivity by doubling tissue controls, while maintaining high specificity (77 %).

Method and system for controlling a gasification or partial oxidation process

DOEpatents

Rozelle, Peter L; Der, Victor K

2015-02-10

A method and system for controlling a fuel gasification system includes optimizing a conversion of solid components in the fuel to gaseous fuel components, controlling the flux of solids entrained in the product gas through equipment downstream of the gasifier, and maximizing the overall efficiencies of processes utilizing gasification. A combination of models, when utilized together, can be integrated with existing plant control systems and operating procedures and employed to develop new control systems and operating procedures. Such an approach is further applicable to gasification systems that utilize both dry feed and slurry feed.

Specificity of Good Manufacturing Practice (GMP) for Biomedical Cell Products.

PubMed

Tulina, M A; Pyatigorskaya, N V

2018-03-01

The article describes special aspects of Good Manufacturing Practice (GMP) for biomedical cell products (BMCP) that imply high standards of aseptics throughout the entire productio process, strict requirements to donors and to the procedure of biomaterial isolation, guaranty of tracing BMCP products, defining processing procedures which allow to identify BMCP as minimally manipulated; continuous quality control and automation of the control process at all stages of manufacturing, which will ensure product release simultaneously with completion of technological operations.

Acceptance procedures for dense-graded mixes

DOT National Transportation Integrated Search

2001-03-01

Recent literature related to acceptance procedures for dense-graded mixtures is summarized. Current state of practice and development of acceptance procedures are reviewed. Many agencies are reducing the number of process control-related parameters i...

A method of setting limits for the purpose of quality assurance

NASA Astrophysics Data System (ADS)

Sanghangthum, Taweap; Suriyapee, Sivalee; Kim, Gwe-Ya; Pawlicki, Todd

2013-10-01

The result from any assurance measurement needs to be checked against some limits for acceptability. There are two types of limits; those that define clinical acceptability (action limits) and those that are meant to serve as a warning that the measurement is close to the action limits (tolerance limits). Currently, there is no standard procedure to set these limits. In this work, we propose an operational procedure to set tolerance limits and action limits. The approach to establish the limits is based on techniques of quality engineering using control charts and a process capability index. The method is different for tolerance limits and action limits with action limits being categorized into those that are specified and unspecified. The procedure is to first ensure process control using the I-MR control charts. Then, the tolerance limits are set equal to the control chart limits on the I chart. Action limits are determined using the Cpm process capability index with the requirements that the process must be in-control. The limits from the proposed procedure are compared to an existing or conventional method. Four examples are investigated: two of volumetric modulated arc therapy (VMAT) point dose quality assurance (QA) and two of routine linear accelerator output QA. The tolerance limits range from about 6% larger to 9% smaller than conventional action limits for VMAT QA cases. For the linac output QA, tolerance limits are about 60% smaller than conventional action limits. The operational procedure describe in this work is based on established quality management tools and will provide a systematic guide to set up tolerance and action limits for different equipment and processes.

10 CFR 71.119 - Control of special processes.

Code of Federal Regulations, 2010 CFR

2010-01-01

... shall establish measures to assure that special processes, including welding, heat treating, and nondestructive testing are controlled and accomplished by qualified personnel using qualified procedures in...

40 CFR 240.205-2 - Recommended procedures: Design.

Code of Federal Regulations, 2010 CFR

2010-07-01

....205-2 Section 240.205-2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures... air pollution control technology. (b) All emissions, including dust from vents, should be controlled. ...

40 CFR 240.205-2 - Recommended procedures: Design.

Code of Federal Regulations, 2011 CFR

2011-07-01

....205-2 Section 240.205-2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures... air pollution control technology. (b) All emissions, including dust from vents, should be controlled. ...

Acceptance procedures for dense-graded mixes : literature review.

DOT National Transportation Integrated Search

2001-03-01

Recent literature related to acceptance procedures for dense-graded mixtures is summarized. Current state of practice and development of acceptance procedures are reviewed. Many agencies are reducing the number of process control-related parameters i...

The Use of Statistical Process Control-Charts for Person-Fit Analysis on Computerized Adaptive Testing. LSAC Research Report Series.

ERIC Educational Resources Information Center

Meijer, Rob R.; van Krimpen-Stoop, Edith M. L. A.

In this study a cumulative-sum (CUSUM) procedure from the theory of Statistical Process Control was modified and applied in the context of person-fit analysis in a computerized adaptive testing (CAT) environment. Six person-fit statistics were proposed using the CUSUM procedure, and three of them could be used to investigate the CAT in online test…

Computer-Mediated Group Processes in Distributed Command and Control Systems

DTIC Science & Technology

1988-06-01

Linville, "Michael J. Liebhaber, and Richard W. Obermayer Vreuls Corporation Jon J. Fallesen Army Research Institute DTIC SELECTEr • AUG I 1. 1988 ARI...control staffs who will operate in a computer- mediated environment. The Army Research Institute has initiated research to examine selected issues...computar-mediated group processes is needed. Procedure: The identification and selection of key research issues followed a three- step procedure. Previous

In-Trail Procedure Air Traffic Control Procedures Validation Simulation Study

NASA Technical Reports Server (NTRS)

Chartrand, Ryan C.; Hewitt, Katrin P.; Sweeney, Peter B.; Graff, Thomas J.; Jones, Kenneth M.

2012-01-01

In August 2007, Airservices Australia (Airservices) and the United States National Aeronautics and Space Administration (NASA) conducted a validation experiment of the air traffic control (ATC) procedures associated with the Automatic Dependant Surveillance-Broadcast (ADS-B) In-Trail Procedure (ITP). ITP is an Airborne Traffic Situation Awareness (ATSA) application designed for near-term use in procedural airspace in which ADS-B data are used to facilitate climb and descent maneuvers. NASA and Airservices conducted the experiment in Airservices simulator in Melbourne, Australia. Twelve current operational air traffic controllers participated in the experiment, which identified aspects of the ITP that could be improved (mainly in the communication and controller approval process). Results showed that controllers viewed the ITP as valid and acceptable. This paper describes the experiment design and results.

40 CFR 1066.275 - Daily dynamometer readiness verification.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) AIR POLLUTION CONTROLS VEHICLE-TESTING PROCEDURES Dynamometer Specifications § 1066.275 Daily... automated process for this verification procedure, perform this evaluation by setting the initial speed and... your dynamometer does not perform this verification with an automated process: (1) With the dynamometer...

40 CFR 63.1412 - Continuous process vent applicability assessment procedures and methods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... engineering principles, measurable process parameters, or physical or chemical laws or properties. Examples of... values, and engineering assessment control applicability assessment requirements are to be determined... by using the engineering assessment procedures in paragraph (k) of this section. (f) Volumetric flow...

40 CFR 63.1412 - Continuous process vent applicability assessment procedures and methods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... engineering principles, measurable process parameters, or physical or chemical laws or properties. Examples of... values, and engineering assessment control applicability assessment requirements are to be determined... by using the engineering assessment procedures in paragraph (k) of this section. (f) Volumetric flow...

40 CFR 63.1412 - Continuous process vent applicability assessment procedures and methods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... engineering principles, measurable process parameters, or physical or chemical laws or properties. Examples of... values, and engineering assessment control applicability assessment requirements are to be determined... by using the engineering assessment procedures in paragraph (k) of this section. (f) Volumetric flow...

40 CFR 63.1412 - Continuous process vent applicability assessment procedures and methods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... engineering principles, measurable process parameters, or physical or chemical laws or properties. Examples of... values, and engineering assessment control applicability assessment requirements are to be determined... by using the engineering assessment procedures in paragraph (k) of this section. (f) Volumetric flow...

40 CFR 63.1412 - Continuous process vent applicability assessment procedures and methods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... engineering principles, measurable process parameters, or physical or chemical laws or properties. Examples of... values, and engineering assessment control applicability assessment requirements are to be determined... by using the engineering assessment procedures in paragraph (k) of this section. (f) Volumetric flow...

14 CFR 21.303 - Replacement and modification parts.

Code of Federal Regulations, 2010 CFR

2010-01-01

... determination can be made. Statistical quality control procedures may be employed where it is shown that a... AIRCRAFT CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS Approval of Materials, Parts, Processes, and... the configuration of the part; and (ii) Information on dimensions, materials, and processes necessary...

Reduced state feedback gain computation. [optimization and control theory for aircraft control

NASA Technical Reports Server (NTRS)

Kaufman, H.

1976-01-01

Because application of conventional optimal linear regulator theory to flight controller design requires the capability of measuring and/or estimating the entire state vector, it is of interest to consider procedures for computing controls which are restricted to be linear feedback functions of a lower dimensional output vector and which take into account the presence of measurement noise and process uncertainty. Therefore, a stochastic linear model that was developed is presented which accounts for aircraft parameter and initial uncertainty, measurement noise, turbulence, pilot command and a restricted number of measurable outputs. Optimization with respect to the corresponding output feedback gains was performed for both finite and infinite time performance indices without gradient computation by using Zangwill's modification of a procedure originally proposed by Powell. Results using a seventh order process show the proposed procedures to be very effective.

Fuzzy Adaptive Control for Intelligent Autonomous Space Exploration Problems

NASA Technical Reports Server (NTRS)

Esogbue, Augustine O.

1998-01-01

The principal objective of the research reported here is the re-design, analysis and optimization of our newly developed neural network fuzzy adaptive controller model for complex processes capable of learning fuzzy control rules using process data and improving its control through on-line adaption. The learned improvement is according to a performance objective function that provides evaluative feedback; this performance objective is broadly defined to meet long-range goals over time. Although fuzzy control had proven effective for complex, nonlinear, imprecisely-defined processes for which standard models and controls are either inefficient, impractical or cannot be derived, the state of the art prior to our work showed that procedures for deriving fuzzy control, however, were mostly ad hoc heuristics. The learning ability of neural networks was exploited to systematically derive fuzzy control and permit on-line adaption and in the process optimize control. The operation of neural networks integrates very naturally with fuzzy logic. The neural networks which were designed and tested using simulation software and simulated data, followed by realistic industrial data were reconfigured for application on several platforms as well as for the employment of improved algorithms. The statistical procedures of the learning process were investigated and evaluated with standard statistical procedures (such as ANOVA, graphical analysis of residuals, etc.). The computational advantage of dynamic programming-like methods of optimal control was used to permit on-line fuzzy adaptive control. Tests for the consistency, completeness and interaction of the control rules were applied. Comparisons to other methods and controllers were made so as to identify the major advantages of the resulting controller model. Several specific modifications and extensions were made to the original controller. Additional modifications and explorations have been proposed for further study. Some of these are in progress in our laboratory while others await additional support. All of these enhancements will improve the attractiveness of the controller as an effective tool for the on line control of an array of complex process environments.

75 FR 76082 - Agency Information Collection (Credit Underwriting Standards and Procedures for Processing VA...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-07

... DEPARTMENT OF VETERANS AFFAIRS [OMB Control No. 2900-0521] Agency Information Collection (Credit Underwriting Standards and Procedures for Processing VA Guaranteed Loans) Activity Under OMB Review AGENCY... information abstracted below to the Office of Management and Budget (OMB) for review and comment. The PRA...

75 FR 60171 - Proposed Information Collection (Credit Underwriting Standards and Procedures for Processing VA...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-29

... DEPARTMENT OF VETERANS AFFAIRS [OMB Control No. 2900-0521] Proposed Information Collection (Credit Underwriting Standards and Procedures for Processing VA Guaranteed Loans) Activity: Comment Request AGENCY... comment on the proposed collection of certain information by the agency. Under the Paperwork Reduction Act...

78 FR 60379 - Proposed Information Collection (Credit Underwriting Standards and Procedures for Processing VA...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-01

... DEPARTMENT OF VETERANS AFFAIRS [OMB Control No. 2900-0521] Proposed Information Collection (Credit Underwriting Standards and Procedures for Processing VA Guaranteed Loans) Activity: Comment Request AGENCY... comment on the proposed collection of certain information by the agency. Under the Paperwork Reduction Act...

40 CFR 63.144 - Process wastewater provisions-test methods and procedures for determining applicability and Group...

Code of Federal Regulations, 2013 CFR

2013-07-01

... and Group 1/Group 2 determinations (determining which wastewater streams require control). (a... methods and procedures for determining applicability and Group 1/Group 2 determinations (determining which wastewater streams require control). 63.144 Section 63.144 Protection of Environment ENVIRONMENTAL PROTECTION...

40 CFR 63.144 - Process wastewater provisions-test methods and procedures for determining applicability and Group...

Code of Federal Regulations, 2010 CFR

2010-07-01

... and Group 1/Group 2 determinations (determining which wastewater streams require control). (a... methods and procedures for determining applicability and Group 1/Group 2 determinations (determining which wastewater streams require control). 63.144 Section 63.144 Protection of Environment ENVIRONMENTAL PROTECTION...

40 CFR 63.144 - Process wastewater provisions-test methods and procedures for determining applicability and Group...

Code of Federal Regulations, 2014 CFR

2014-07-01

... and Group 1/Group 2 determinations (determining which wastewater streams require control). (a... methods and procedures for determining applicability and Group 1/Group 2 determinations (determining which wastewater streams require control). 63.144 Section 63.144 Protection of Environment ENVIRONMENTAL PROTECTION...

40 CFR 63.144 - Process wastewater provisions-test methods and procedures for determining applicability and Group...

Code of Federal Regulations, 2011 CFR

2011-07-01

... and Group 1/Group 2 determinations (determining which wastewater streams require control). (a... methods and procedures for determining applicability and Group 1/Group 2 determinations (determining which wastewater streams require control). 63.144 Section 63.144 Protection of Environment ENVIRONMENTAL PROTECTION...

40 CFR 63.144 - Process wastewater provisions-test methods and procedures for determining applicability and Group...

Code of Federal Regulations, 2012 CFR

2012-07-01

... and Group 1/Group 2 determinations (determining which wastewater streams require control). (a... methods and procedures for determining applicability and Group 1/Group 2 determinations (determining which wastewater streams require control). 63.144 Section 63.144 Protection of Environment ENVIRONMENTAL PROTECTION...

On the efficacy of using the transfer-controlled procedure during periods of STP processor overloads in SS7 networks

NASA Astrophysics Data System (ADS)

Rumsewicz, Michael

1994-04-01

In this paper, we examine call completion performance, rather than message throughput, in a Common Channel Signaling network in which the processing resources, and not transmission resources, of a Signaling Transfer Point (STP) are overloaded. Specifically, we perform a transient analysis, via simulation, of a network consisting of a single Central Processor-based STP connecting many local exchanges. We consider the efficacy of using the Transfer Controlled (TFC) procedure when the network call attempt rate exceeds the processing capability of the STP. We find the following: (1) the success of the control depends critically on the rate at which TFC's are sent; (2) use of the TFC procedure in theevent of processor overload can provide reasonable call completion rates.

Incidental learning of sound categories is impaired in developmental dyslexia.

PubMed

Gabay, Yafit; Holt, Lori L

2015-12-01

Developmental dyslexia is commonly thought to arise from specific phonological impairments. However, recent evidence is consistent with the possibility that phonological impairments arise as symptoms of an underlying dysfunction of procedural learning. The nature of the link between impaired procedural learning and phonological dysfunction is unresolved. Motivated by the observation that speech processing involves the acquisition of procedural category knowledge, the present study investigates the possibility that procedural learning impairment may affect phonological processing by interfering with the typical course of phonetic category learning. The present study tests this hypothesis while controlling for linguistic experience and possible speech-specific deficits by comparing auditory category learning across artificial, nonlinguistic sounds among dyslexic adults and matched controls in a specialized first-person shooter videogame that has been shown to engage procedural learning. Nonspeech auditory category learning was assessed online via within-game measures and also with a post-training task involving overt categorization of familiar and novel sound exemplars. Each measure reveals that dyslexic participants do not acquire procedural category knowledge as effectively as age- and cognitive-ability matched controls. This difference cannot be explained by differences in perceptual acuity for the sounds. Moreover, poor nonspeech category learning is associated with slower phonological processing. Whereas phonological processing impairments have been emphasized as the cause of dyslexia, the current results suggest that impaired auditory category learning, general in nature and not specific to speech signals, could contribute to phonological deficits in dyslexia with subsequent negative effects on language acquisition and reading. Implications for the neuro-cognitive mechanisms of developmental dyslexia are discussed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Incidental Learning of Sound Categories is Impaired in Developmental Dyslexia

PubMed Central

Gabay, Yafit; Holt, Lori L.

2015-01-01

Developmental dyslexia is commonly thought to arise from specific phonological impairments. However, recent evidence is consistent with the possibility that phonological impairments arise as symptoms of an underlying dysfunction of procedural learning. The nature of the link between impaired procedural learning and phonological dysfunction is unresolved. Motivated by the observation that speech processing involves the acquisition of procedural category knowledge, the present study investigates the possibility that procedural learning impairment may affect phonological processing by interfering with the typical course of phonetic category learning. The present study tests this hypothesis while controlling for linguistic experience and possible speech-specific deficits by comparing auditory category learning across artificial, nonlinguistic sounds among dyslexic adults and matched controls in a specialized first-person shooter videogame that has been shown to engage procedural learning. Nonspeech auditory category learning was assessed online via within-game measures and also with a post-training task involving overt categorization of familiar and novel sound exemplars. Each measure reveals that dyslexic participants do not acquire procedural category knowledge as effectively as age- and cognitive-ability matched controls. This difference cannot be explained by differences in perceptual acuity for the sounds. Moreover, poor nonspeech category learning is associated with slower phonological processing. Whereas phonological processing impairments have been emphasized as the cause of dyslexia, the current results suggest that impaired auditory category learning, general in nature and not specific to speech signals, could contribute to phonological deficits in dyslexia with subsequent negative effects on language acquisition and reading. Implications for the neuro-cognitive mechanisms of developmental dyslexia are discussed. PMID:26409017

21 CFR 106.1 - Status and applicability of the quality control procedures regulation.

Code of Federal Regulations, 2011 CFR

2011-04-01

... AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION INFANT FORMULA QUALITY CONTROL PROCEDURES... infant formula meets the safety, quality, and nutrient requirements of section 412 of the act and the..., processing, and packaging of an infant formula shall render such formula adulterated under section 412(a)(1...

21 CFR 106.1 - Status and applicability of the quality control procedures regulation.

Code of Federal Regulations, 2010 CFR

2010-04-01

... AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION INFANT FORMULA QUALITY CONTROL PROCEDURES... infant formula meets the safety, quality, and nutrient requirements of section 412 of the act and the..., processing, and packaging of an infant formula shall render such formula adulterated under section 412(a)(1...

Simulation of Simple Controlled Processes with Dead-Time.

ERIC Educational Resources Information Center

Watson, Keith R.; And Others

1985-01-01

The determination of closed-loop response of processes containing dead-time is typically not covered in undergraduate process control, possibly because the solution by Laplace transforms requires the use of Pade approximation for dead-time, which makes the procedure lengthy and tedious. A computer-aided method is described which simplifies the…

Contamination control in hybrid microelectronic modules. Identification of critical process and contaminants, part 1

NASA Technical Reports Server (NTRS)

Himmel, R. P.

1975-01-01

Hybrid processes, handling procedures, and materials were examined to identify the critical process steps in which contamination is most likely to occur, to identify the particular contaminants associated with these critical steps, and to propose method for the control of these contaminants.

Progressive freezing and sweating in a test unit

NASA Astrophysics Data System (ADS)

Ulrich, J.; Özoğuz, Y.

1990-01-01

Crystallization from melts is applied in several fields like waste water treatment, fruit juice or liquid food concentration and purification of organic chemicals. Investigations to improve the understanding, the performance and the control of the process have been carried out. The experimental unit used a vertical tube with a falling film on the outside. With an specially designed measuring technique process controlling parameters have been studied. The results demonstrate the dependency of those parameters upon each other and indicate the way to control the process by controlling the dominant parameter. This is the growth rate of the crystal coat. A further purification of the crystal layer can be achieved by introducing the procedure of sweating, which is a controlled partial melting of the crystal coat. Here again process parameters have been varied and results are presented. The strong effect upon the final purity of the product by an efficient executed sweating which is effectively tuned on the crystallization procedure should save crystallization steps, energy and time.

AMPS data management concepts. [Atmospheric, Magnetospheric and Plasma in Space experiment

NASA Technical Reports Server (NTRS)

Metzelaar, P. N.

1975-01-01

Five typical AMPS experiments were formulated to allow simulation studies to verify data management concepts. Design studies were conducted to analyze these experiments in terms of the applicable procedures, data processing and displaying functions. Design concepts for AMPS data management system are presented which permit both automatic repetitive measurement sequences and experimenter-controlled step-by-step procedures. Extensive use is made of a cathode ray tube display, the experimenters' alphanumeric keyboard, and the computer. The types of computer software required by the system and the possible choices of control and display procedures available to the experimenter are described for several examples. An electromagnetic wave transmission experiment illustrates the methods used to analyze data processing requirements.

Specific arithmetic calculation deficits in children with Turner syndrome.

PubMed

Rovet, J; Szekely, C; Hockenberry, M N

1994-12-01

Study 1 compared arithmetic processing skills on the WRAT-R in 45 girls with Turner syndrome (TS) and 92 age-matched female controls. Results revealed significant underachievement by subjects with TS, which reflected their poorer performance on problems requiring the retrieval of addition and multiplication facts and procedural knowledge for addition and division operations. TS subjects did not differ qualitatively from controls in type of procedural error committed. Study 2, which compared the performance of 10 subjects with TS and 31 controls on the Keymath Diagnostic Arithmetic Test, showed that the TS group had less adequate knowledge of arithmetic, subtraction, and multiplication procedures but did not differ from controls on Fact items. Error analyses revealed that TS subjects were more likely to confuse component steps or fail to separate intermediate steps or to complete problems. TS subjects relied to a greater degree on verbal than visual-spatial abilities in arithmetic processing while their visual-spatial abilities were associated with retrieval of simple multidigit addition facts and knowledge of subtraction, multiplication, and division procedures. Differences between the TS and control groups increased with age for Keymath, but not WRAT-R, procedures. Discrepant findings are related to the different task constraints (timed vs. untimed, single vs. alternate versions, size of item pool) and the use of different strategies (counting vs. fact retrieval). It is concluded that arithmetic difficulties in females with TS are due to less adequate procedural skills, combined with poorer fact retrieval in timed testing situations, rather than to inadequate visual-spatial abilities.

Computation of output feedback gains for linear stochastic systems using the Zangnill-Powell Method

NASA Technical Reports Server (NTRS)

Kaufman, H.

1975-01-01

Because conventional optimal linear regulator theory results in a controller which requires the capability of measuring and/or estimating the entire state vector, it is of interest to consider procedures for computing controls which are restricted to be linear feedback functions of a lower dimensional output vector and which take into account the presence of measurement noise and process uncertainty. To this effect a stochastic linear model has been developed that accounts for process parameter and initial uncertainty, measurement noise, and a restricted number of measurable outputs. Optimization with respect to the corresponding output feedback gains was then performed for both finite and infinite time performance indices without gradient computation by using Zangwill's modification of a procedure originally proposed by Powell. Results using a seventh order process show the proposed procedures to be very effective.

42 CFR 485.725 - Condition of participation: Infection control.

Code of Federal Regulations, 2010 CFR

2010-10-01

... procedures for effective aseptic techniques. The procedures are reviewed annually and revised if necessary to... handled, stored, processed, and transported in such a manner as to prevent the spread of infection. (e...

Application of systems and control theory-based hazard analysis to radiation oncology.

PubMed

Pawlicki, Todd; Samost, Aubrey; Brown, Derek W; Manger, Ryan P; Kim, Gwe-Ya; Leveson, Nancy G

2016-03-01

Both humans and software are notoriously challenging to account for in traditional hazard analysis models. The purpose of this work is to investigate and demonstrate the application of a new, extended accident causality model, called systems theoretic accident model and processes (STAMP), to radiation oncology. Specifically, a hazard analysis technique based on STAMP, system-theoretic process analysis (STPA), is used to perform a hazard analysis. The STPA procedure starts with the definition of high-level accidents for radiation oncology at the medical center and the hazards leading to those accidents. From there, the hierarchical safety control structure of the radiation oncology clinic is modeled, i.e., the controls that are used to prevent accidents and provide effective treatment. Using STPA, unsafe control actions (behaviors) are identified that can lead to the hazards as well as causal scenarios that can lead to the identified unsafe control. This information can be used to eliminate or mitigate potential hazards. The STPA procedure is demonstrated on a new online adaptive cranial radiosurgery procedure that omits the CT simulation step and uses CBCT for localization, planning, and surface imaging system during treatment. The STPA procedure generated a comprehensive set of causal scenarios that are traced back to system hazards and accidents. Ten control loops were created for the new SRS procedure, which covered the areas of hospital and department management, treatment design and delivery, and vendor service. Eighty three unsafe control actions were identified as well as 472 causal scenarios that could lead to those unsafe control actions. STPA provides a method for understanding the role of management decisions and hospital operations on system safety and generating process design requirements to prevent hazards and accidents. The interaction of people, hardware, and software is highlighted. The method of STPA produces results that can be used to improve safety and prevent accidents and warrants further investigation.

12 CFR 367.12 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Procedures. 367.12 Section 367.12 Banks and... EXCLUSION OF CONTRACTOR AND TERMINATION OF CONTRACTS § 367.12 Procedures. (a) FDIC shall process suspension... reconsideration, the provisions relating to the construction of time limits in 12 CFR 308.12 will control. ...

Lab Procedures. Sludge Treatment and Disposal Course #166. Instructor's Guide [and] Student Workbook.

ERIC Educational Resources Information Center

Carnegie, John W.

Laboratory tests used to determine status and to evaluate and/or maintain process control of the various sludge treatment processes are introduced in this lesson. Neither detailed test procedures nor explanations of how the tests should be applied to every unit are explained; this information is provided in other modules. The instructor's manual…

Timeliner: Automating Procedures on the ISS

NASA Technical Reports Server (NTRS)

Brown, Robert; Braunstein, E.; Brunet, Rick; Grace, R.; Vu, T.; Zimpfer, Doug; Dwyer, William K.; Robinson, Emily

2002-01-01

Timeliner has been developed as a tool to automate procedural tasks. These tasks may be sequential tasks that would typically be performed by a human operator, or precisely ordered sequencing tasks that allow autonomous execution of a control process. The Timeliner system includes elements for compiling and executing sequences that are defined in the Timeliner language. The Timeliner language was specifically designed to allow easy definition of scripts that provide sequencing and control of complex systems. The execution environment provides real-time monitoring and control based on the commands and conditions defined in the Timeliner language. The Timeliner sequence control may be preprogrammed, compiled from Timeliner "scripts," or it may consist of real-time, interactive inputs from system operators. In general, the Timeliner system lowers the workload for mission or process control operations. In a mission environment, scripts can be used to automate spacecraft operations including autonomous or interactive vehicle control, performance of preflight and post-flight subsystem checkouts, or handling of failure detection and recovery. Timeliner may also be used for mission payload operations, such as stepping through pre-defined procedures of a scientific experiment.

40 CFR 63.1426 - Process vent requirements for determining organic HAP concentration, control efficiency, and...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Production § 63.1426 Process vent requirements for determining organic HAP concentration, control efficiency..., total organic HAP, or as TOC minus methane and ethane according to the procedures specified. When... methane and ethane) concentrations in all process vent streams and primary and secondary fuels introduced...

Improved compliance by BPM-driven workflow automation.

PubMed

Holzmüller-Laue, Silke; Göde, Bernd; Fleischer, Heidi; Thurow, Kerstin

2014-12-01

Using methods and technologies of business process management (BPM) for the laboratory automation has important benefits (i.e., the agility of high-level automation processes, rapid interdisciplinary prototyping and implementation of laboratory tasks and procedures, and efficient real-time process documentation). A principal goal of the model-driven development is the improved transparency of processes and the alignment of process diagrams and technical code. First experiences of using the business process model and notation (BPMN) show that easy-to-read graphical process models can achieve and provide standardization of laboratory workflows. The model-based development allows one to change processes quickly and an easy adaption to changing requirements. The process models are able to host work procedures and their scheduling in compliance with predefined guidelines and policies. Finally, the process-controlled documentation of complex workflow results addresses modern laboratory needs of quality assurance. BPMN 2.0 as an automation language to control every kind of activity or subprocess is directed to complete workflows in end-to-end relationships. BPMN is applicable as a system-independent and cross-disciplinary graphical language to document all methods in laboratories (i.e., screening procedures or analytical processes). That means, with the BPM standard, a communication method of sharing process knowledge of laboratories is also available. © 2014 Society for Laboratory Automation and Screening.

Contamination-Free Manufacturing: Tool Component Qualification, Verification and Correlation with Wafers

NASA Astrophysics Data System (ADS)

Tan, Samantha H.; Chen, Ning; Liu, Shi; Wang, Kefei

2003-09-01

As part of the semiconductor industry "contamination-free manufacturing" effort, significant emphasis has been placed on reducing potential sources of contamination from process equipment and process equipment components. Process tools contain process chambers and components that are exposed to the process environment or process chemistry and in some cases are in direct contact with production wafers. Any contamination from these sources must be controlled or eliminated in order to maintain high process yields, device performance, and device reliability. This paper discusses new nondestructive analytical methods for quantitative measurement of the cleanliness of metal, quartz, polysilicon and ceramic components that are used in process equipment tools. The goal of these new procedures is to measure the effectiveness of cleaning procedures and to verify whether a tool component part is sufficiently clean for installation and subsequent routine use in the manufacturing line. These procedures provide a reliable "qualification method" for tool component certification and also provide a routine quality control method for reliable operation of cleaning facilities. Cost advantages to wafer manufacturing include higher yields due to improved process cleanliness and elimination of yield loss and downtime resulting from the installation of "bad" components in process tools. We also discuss a representative example of wafer contamination having been linked to a specific process tool component.

New method of control of tooth whitening

NASA Astrophysics Data System (ADS)

Angelov, I.; Mantareva, V.; Gisbrecht, A.; Valkanov, S.; Uzunov, Tz.

2010-10-01

New methods of control of tooth bleaching stages through simultaneous measurements of a reflected light and a fluorescence signal are proposed. It is shown that the bleaching process leads to significant changes in the intensity of a scattered signal and also in the shape and intensity of the fluorescence spectra. Experimental data illustrate that the bleaching process causes essential changes in the teeth discoloration in short time as 8-10 min from the beginning of the application procedure. The continuation of the treatment is not necessary moreover the probability of the enamel destroy increases considerably. The proposed optical back control of tooth surface is a base for development of a practical set up to control the duration of the bleaching procedure.

Six Sigma methods applied to cryogenic coolers assembly line

NASA Astrophysics Data System (ADS)

Ventre, Jean-Marc; Germain-Lacour, Michel; Martin, Jean-Yves; Cauquil, Jean-Marc; Benschop, Tonny; Griot, René

2009-05-01

Six Sigma method have been applied to manufacturing process of a rotary Stirling cooler: RM2. Name of the project is NoVa as main goal of the Six Sigma approach is to reduce variability (No Variability). Project has been based on the DMAIC guideline following five stages: Define, Measure, Analyse, Improve, Control. Objective has been set on the rate of coolers succeeding performance at first attempt with a goal value of 95%. A team has been gathered involving people and skills acting on the RM2 manufacturing line. Measurement System Analysis (MSA) has been applied to test bench and results after R&R gage show that measurement is one of the root cause for variability in RM2 process. Two more root causes have been identified by the team after process mapping analysis: regenerator filling factor and cleaning procedure. Causes for measurement variability have been identified and eradicated as shown by new results from R&R gage. Experimental results show that regenerator filling factor impacts process variability and affects yield. Improved process haven been set after new calibration process for test bench, new filling procedure for regenerator and an additional cleaning stage have been implemented. The objective for 95% coolers succeeding performance test at first attempt has been reached and kept for a significant period. RM2 manufacturing process is now managed according to Statistical Process Control based on control charts. Improvement in process capability have enabled introduction of sample testing procedure before delivery.

Classical and modern control strategies for the deployment, reconfiguration, and station-keeping of the National Aeronautics and Space Administration (NASA) Benchmark Tetrahedron Constellation

NASA Astrophysics Data System (ADS)

Capo-Lugo, Pedro A.

Formation flying consists of multiple spacecraft orbiting in a required configuration about a planet or through Space. The National Aeronautics and Space Administration (NASA) Benchmark Tetrahedron Constellation is one of the proposed constellations to be launched in the year 2009 and provides the motivation for this investigation. The problem that will be researched here consists of three stages. The first stage contains the deployment of the satellites; the second stage is the reconfiguration process to transfer the satellites through different specific sizes of the NASA benchmark problem; and, the third stage is the station-keeping procedure for the tetrahedron constellation. Every stage contains different control schemes and transfer procedures to obtain/maintain the proposed tetrahedron constellation. In the first stage, the deployment procedure will depend on a combination of two techniques in which impulsive maneuvers and a digital controller are used to deploy the satellites and to maintain the tetrahedron constellation at the following apogee point. The second stage that corresponds to the reconfiguration procedure shows a different control scheme in which the intelligent control systems are implemented to perform this procedure. In this research work, intelligent systems will eliminate the use of complex mathematical models and will reduce the computational time to perform different maneuvers. Finally, the station-keeping process, which is the third stage of this research problem, will be implemented with a two-level hierarchical control scheme to maintain the separation distance constraints of the NASA Benchmark Tetrahedron Constellation. For this station-keeping procedure, the system of equations defining the dynamics of a pair of satellites is transformed to take in account the perturbation due to the oblateness of the Earth and the disturbances due to solar pressure. The control procedures used in this research will be transformed from a continuous control system to a digital control system which will simplify the implementation into the computer onboard the satellite. In addition, this research will show an introductory chapter on attitude dynamics that can be used to maintain the orientation of the satellites, and an adaptive intelligent control scheme will be proposed to maintain the desired orientation of the spacecraft. In conclusion, a solution for the dynamics of the NASA Benchmark Tetrahedron Constellation will be presented in this research work. The main contribution of this work is the use of discrete control schemes, impulsive maneuvers, and intelligent control schemes that can be used to reduce the computational time in which these control schemes can be easily implemented in the computer onboard the satellite. These contributions are explained through the deployment, reconfiguration, and station-keeping process of the proposed NASA Benchmark Tetrahedron Constellation.

Application of Sigma Metrics Analysis for the Assessment and Modification of Quality Control Program in the Clinical Chemistry Laboratory of a Tertiary Care Hospital.

PubMed

Iqbal, Sahar; Mustansar, Tazeen

2017-03-01

Sigma is a metric that quantifies the performance of a process as a rate of Defects-Per-Million opportunities. In clinical laboratories, sigma metric analysis is used to assess the performance of laboratory process system. Sigma metric is also used as a quality management strategy for a laboratory process to improve the quality by addressing the errors after identification. The aim of this study is to evaluate the errors in quality control of analytical phase of laboratory system by sigma metric. For this purpose sigma metric analysis was done for analytes using the internal and external quality control as quality indicators. Results of sigma metric analysis were used to identify the gaps and need for modification in the strategy of laboratory quality control procedure. Sigma metric was calculated for quality control program of ten clinical chemistry analytes including glucose, chloride, cholesterol, triglyceride, HDL, albumin, direct bilirubin, total bilirubin, protein and creatinine, at two control levels. To calculate the sigma metric imprecision and bias was calculated with internal and external quality control data, respectively. The minimum acceptable performance was considered as 3 sigma. Westgard sigma rules were applied to customize the quality control procedure. Sigma level was found acceptable (≥3) for glucose (L2), cholesterol, triglyceride, HDL, direct bilirubin and creatinine at both levels of control. For rest of the analytes sigma metric was found <3. The lowest value for sigma was found for chloride (1.1) at L2. The highest value of sigma was found for creatinine (10.1) at L3. HDL was found with the highest sigma values at both control levels (8.8 and 8.0 at L2 and L3, respectively). We conclude that analytes with the sigma value <3 are required strict monitoring and modification in quality control procedure. In this study application of sigma rules provided us the practical solution for improved and focused design of QC procedure.

Using a multimedia presentation to improve patient understanding and satisfaction with informed consent for minimally invasive vascular procedures.

PubMed

Bowers, N; Eisenberg, E; Montbriand, J; Jaskolka, J; Roche-Nagle, G

2017-02-01

As vascular procedures become more complex, patient understanding of their treatment(s) can become more difficult. We wished to evaluate the utility of multimedia presentations (MPs) to improve patient understanding of their vascular interventions. Patients undergoing endovascular aneurysm repair (EVAR), peripheral angioplasty, Hickman catheter and peripherally inserted central catheter (PICC) insertion were randomized into a control group receiving traditional verbal consent, and a MP group that were shown a two minute simplified video of their procedure on an iPad™ computer in addition to the traditional verbal consent. After obtaining consent, all patients completed a questionnaire assessing their comprehension of the procedure, and satisfaction with the consent process. Satisfaction was rated on a 5 point Likert scale with 5 being 'very helpful' in understanding the procedure. Ninety-three patients were recruited for this study, 62% of which were male. The intervention significantly increased total comprehension in all procedure types controlling for procedure type (multimedia vs. control; F = 9.14, P = .003). A second ANOVA showed there was a significant main effect by intervention (F = 44.06, p < .000) with those in the intervention group showing higher overall satisfaction scores after controlling for surgery type. This study suggests that patients find the use of MP during the consent process to be helpful in patient understanding and that there is improved satisfaction. Given the rapid rate of innovation in vascular interventions, increased regular use of MPs to help patients understand their procedures would be beneficial in the care of patients undergoing vascular interventions. Copyright © 2015 Royal College of Surgeons of Edinburgh (Scottish charity number SC005317) and Royal College of Surgeons in Ireland. Published by Elsevier Ltd. All rights reserved.

The procedure execution manager and its application to Advanced Photon Source operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borland, M.

1997-06-01

The Procedure Execution Manager (PEM) combines a complete scripting environment for coding accelerator operation procedures with a manager application for executing and monitoring the procedures. PEM is based on Tcl/Tk, a supporting widget library, and the dp-tcl extension for distributed processing. The scripting environment provides support for distributed, parallel execution of procedures along with join and abort operations. Nesting of procedures is supported, permitting the same code to run as a top-level procedure under operator control or as a subroutine under control of another procedure. The manager application allows an operator to execute one or more procedures in automatic, semi-automatic,more » or manual modes. It also provides a standard way for operators to interact with procedures. A number of successful applications of PEM to accelerator operations have been made to date. These include start-up, shutdown, and other control of the positron accumulator ring (PAR), low-energy transport (LET) lines, and the booster rf systems. The PAR/LET procedures make nested use of PEM`s ability to run parallel procedures. There are also a number of procedures to guide and assist tune-up operations, to make accelerator physics measurements, and to diagnose equipment. Because of the success of the existing procedures, expanded use of PEM is planned.« less

14 CFR 21.143 - Quality control data requirements; prime manufacturer.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., purchased items, and parts and assemblies produced by manufacturers' suppliers including methods used to... special manufacturing processes involved, the means used to control the processes, the final test... procedure for recording review board decisions and disposing of rejected parts; (5) An outline of a system...

Generation of control sequences for a pilot-disassembly system

NASA Astrophysics Data System (ADS)

Seliger, Guenther; Kim, Hyung-Ju; Keil, Thomas

2002-02-01

Closing the product and material cycles has emerged as a paradigm for industry in the 21st century. Disassembly plays a key role in a life cycle economy since it enables the recovery of resources. A partly automated disassembly system should adapt to a large variety of products and different degrees of devaluation. Also the amounts of products to be disassembled can vary strongly. To cope with these demands an approach to generate on-line disassembly control sequences will be presented. In order to react on these demands the technological feasibility is considered within a procedure for the generation of disassembly control sequences. Procedures are designed to find available and technologically feasible disassembly processes. The control system is formed by modularised and parameterised control units in the cell level within the entire control architecture. In the first development stage product and process analyses at the sample product washing machine were executed. Furthermore a generalized disassembly process was defined. Afterwards these processes were structured in primary and secondary functions. In the second stage the disassembly control at the technological level was investigated. Factors were the availability of the disassembly tools and the technological feasibility of the disassembly processes within the disassembly system. Technical alternative disassembly processes are determined as a result of availability of the tools and technological feasibility of processes. The fourth phase was the concept for the generation of the disassembly control sequences. The approach will be proved in a prototypical disassembly system.

Supporting the Future Air Traffic Control Projection Process

NASA Technical Reports Server (NTRS)

Davison, Hayley J.; Hansman, R. John, Jr.

2002-01-01

In air traffic control, projecting what the air traffic situation will be over the next 30 seconds to 30 minutes is a key process in identifying conflicts that may arise so that evasive action can be taken upon discovery of these conflicts. A series of field visits in the Boston and New York terminal radar approach control (TRACON) facilities and in the oceanic air traffic control facilities in New York and Reykjavik, Iceland were conducted to investigate the projection process in two different ATC domains. The results from the site visits suggest that two types of projection are currently used in ATC tasks, depending on the type of separation minima and/or traffic restriction and information display used by the controller. As technologies improve and procedures change, care should be taken by designers to support projection through displays, automation, and procedures. It is critical to prevent time/space mismatches between interfaces and restrictions. Existing structure in traffic dynamics could be utilized to provide controllers with useful behavioral models on which to build projections. Subtle structure that the controllers are unable to internalize could be incorporated into an ATC projection aid.

Trends in International Persuasion: Persuasion in the Arms Control Negotiations.

ERIC Educational Resources Information Center

Hopmann, P. Terrence; Walcott, Charles

An analysis of the bargaining process in international arms control negotiations is possible by developing a framework of interrelated hypotheses, by delineating and practicing interactions study called "Bargaining Process Analysis," and by formulating procedural steps that bridge the gap between laboratory studies and "real world" situations. In…

21 CFR 110.80 - Processes and controls.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 2 2014-04-01 2014-04-01 false Processes and controls. 110.80 Section 110.80 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... extraneous-material testing procedures shall be used where necessary to identify sanitation failures or...

21 CFR 110.80 - Processes and controls.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 2 2013-04-01 2013-04-01 false Processes and controls. 110.80 Section 110.80 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... extraneous-material testing procedures shall be used where necessary to identify sanitation failures or...

21 CFR 110.80 - Processes and controls.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 2 2012-04-01 2012-04-01 false Processes and controls. 110.80 Section 110.80 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... extraneous-material testing procedures shall be used where necessary to identify sanitation failures or...

Instrument Quality Control.

PubMed

Jayakody, Chatura; Hull-Ryde, Emily A

2016-01-01

Well-defined quality control (QC) processes are used to determine whether a certain procedure or action conforms to a widely accepted standard and/or set of guidelines, and are important components of any laboratory quality assurance program (Popa-Burke et al., J Biomol Screen 14: 1017-1030, 2009). In this chapter, we describe QC procedures useful for monitoring the accuracy and precision of laboratory instrumentation, most notably automated liquid dispensers. Two techniques, gravimetric QC and photometric QC, are highlighted in this chapter. When used together, these simple techniques provide a robust process for evaluating liquid handler accuracy and precision, and critically underpin high-quality research programs.

The application of rules in morphology, syntax and number processing: a case of selective deficit of procedural or executive mechanisms?

PubMed

Macoir, Joël; Fossard, Marion; Nespoulous, Jean-Luc; Demonet, Jean-François; Bachoud-Lévi, Anne-Catherine

2010-08-01

Declarative memory is a long-term store for facts, concepts and words. Procedural memory subserves the learning and control of sensorimotor and cognitive skills, including the mental grammar. In this study, we report a single-case study of a mild aphasic patient who showed procedural deficits in the presence of preserved declarative memory abilities. We administered several experiments to explore rule application in morphology, syntax and number processing. Results partly support the differentiation between declarative and procedural memory. Moreover, the patient's performance varied according to the domain in which rules were to be applied, which underlines the need for more fine-grained distinctions in cognition between procedural rules.

Optimization of synthesis process of thermally-responsive poly-n-isopropylacrylamide nanoparticles for controlled release of antimicrobial hydrophobic compounds

NASA Astrophysics Data System (ADS)

Hill, Laura E.; Gomes, Carmen L.

2014-12-01

The goal of this study was to develop an effective method to synthesize poly-n-isopropylacrylamide (PNIPAAM) nanoparticles with entrapped cinnamon bark extract (CBE) to improve its delivery to foodborne pathogens and control its release with temperature stimuli. CBE was used as a model for hydrophobic natural antimicrobials. A top-down procedure using crosslinked PNIPAAM was compared to a bottom-up procedure using NIPAAM monomer. Both processes relied on self-assembly of the molecules into micelles around the CBE at 40 °C. Processing conditions were compared including homogenization time of the polymer, hydration time prior to homogenization, lyophilization, and the effect of particle ultrafiltration. The top-down versus bottom-up synthesis methods yielded particles with significantly different characteristics, especially their release profiles and antimicrobial activities. The synthesis methods affected particle size, with the bottom-up procedure resulting in smaller (P < 0.05) diameters than the top-down procedure. The controlled release profile of CBE from nanoparticles was dependent on the release media temperature. A faster, burst release was observed at 40 °C and a slower, more sustained release was observed at lower temperatures. PNIPAAM particles containing CBE were analyzed for their antimicrobial activity against Salmonella enterica serovar Typhimurium LT2 and Listeria monocytogenes Scott A. The PNIPAAM particles synthesized via the top-down procedure had a much faster release, which led to a greater (P < 0.05) antimicrobial activity. Both of the top-down nanoparticles performed similarly, therefore the 7 min homogenization time nanoparticles would be the best for this application, as the process time is shorter and little improvement was seen by using a slightly longer homogenization.

Effectiveness of facilitated introduction of a standard operating procedure into routine processes in the operating theatre: a controlled interrupted time series.

PubMed

Morgan, Lauren; New, Steve; Robertson, Eleanor; Collins, Gary; Rivero-Arias, Oliver; Catchpole, Ken; Pickering, Sharon P; Hadi, Mohammed; Griffin, Damian; McCulloch, Peter

2015-02-01

Standard operating procedures (SOPs) should improve safety in the operating theatre, but controlled studies evaluating the effect of staff-led implementation are needed. In a controlled interrupted time series, we evaluated three team process measures (compliance with WHO surgical safety checklist, non-technical skills and technical performance) and three clinical outcome measures (length of hospital stay, complications and readmissions) before and after a 3-month staff-led development of SOPs. Process measures were evaluated by direct observation, using Oxford Non-Technical Skills II for non-technical skills and the 'glitch count' for technical performance. All staff in two orthopaedic operating theatres were trained in the principles of SOPs and then assisted to develop standardised procedures. Staff in a control operating theatre underwent the same observations but received no training. The change in difference between active and control groups was compared before and after the intervention using repeated measures analysis of variance. We observed 50 operations before and 55 after the intervention and analysed clinical data on 1022 and 861 operations, respectively. The staff chose to structure their efforts around revising the 'whiteboard' which documented and prompted tasks, rather than directly addressing specific task problems. Although staff preferred and sustained the new system, we found no significant differences in process or outcome measures before/after intervention in the active versus the control group. There was a secular trend towards worse outcomes in the postintervention period, seen in both active and control theatres. SOPs when developed and introduced by frontline staff do not necessarily improve operative processes or outcomes. The inherent tension in improvement work between giving staff ownership of improvement and maintaining control of direction needs to be managed, to ensure staff are engaged but invest energy in appropriate change. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Design, Control and in Situ Visualization of Gas Nitriding Processes

PubMed Central

Ratajski, Jerzy; Olik, Roman; Suszko, Tomasz; Dobrodziej, Jerzy; Michalski, Jerzy

2010-01-01

The article presents a complex system of design, in situ visualization and control of the commonly used surface treatment process: the gas nitriding process. In the computer design conception, analytical mathematical models and artificial intelligence methods were used. As a result, possibilities were obtained of the poly-optimization and poly-parametric simulations of the course of the process combined with a visualization of the value changes of the process parameters in the function of time, as well as possibilities to predict the properties of nitrided layers. For in situ visualization of the growth of the nitrided layer, computer procedures were developed which make use of the results of the correlations of direct and differential voltage and time runs of the process result sensor (magnetic sensor), with the proper layer growth stage. Computer procedures make it possible to combine, in the duration of the process, the registered voltage and time runs with the models of the process. PMID:22315536

The implementation of a Hazard Analysis and Critical Control Point management system in a peanut butter ice cream plant.

PubMed

Hung, Yu-Ting; Liu, Chi-Te; Peng, I-Chen; Hsu, Chin; Yu, Roch-Chui; Cheng, Kuan-Chen

2015-09-01

To ensure the safety of the peanut butter ice cream manufacture, a Hazard Analysis and Critical Control Point (HACCP) plan has been designed and applied to the production process. Potential biological, chemical, and physical hazards in each manufacturing procedure were identified. Critical control points for the peanut butter ice cream were then determined as the pasteurization and freezing process. The establishment of a monitoring system, corrective actions, verification procedures, and documentation and record keeping were followed to complete the HACCP program. The results of this study indicate that implementing the HACCP system in food industries can effectively enhance food safety and quality while improving the production management. Copyright © 2015. Published by Elsevier B.V.

Examining procedural working memory processing in obsessive-compulsive disorder.

PubMed

Shahar, Nitzan; Teodorescu, Andrei R; Anholt, Gideon E; Karmon-Presser, Anat; Meiran, Nachshon

2017-07-01

Previous research has suggested that a deficit in working memory might underlie the difficulty of obsessive-compulsive disorder (OCD) patients to control their thoughts and actions. However, a recent meta-analyses found only small effect sizes for working memory deficits in OCD. Recently, a distinction has been made between declarative and procedural working memory. Working memory in OCD was tested mostly using declarative measurements. However, OCD symptoms typically concerns actions, making procedural working-memory more relevant. Here, we tested the operation of procedural working memory in OCD. Participants with OCD and healthy controls performed a battery of choice reaction tasks under high and low procedural working memory demands. Reaction-times (RT) were estimated using ex-Gaussian distribution fitting, revealing no group differences in the size of the RT distribution tail (i.e., τ parameter), known to be sensitive to procedural working memory manipulations. Group differences, unrelated to working memory manipulations, were found in the leading-edge of the RT distribution and analyzed using a two-stage evidence accumulation model. Modeling results suggested that perceptual difficulties might underlie the current group differences. In conclusion, our results suggest that procedural working-memory processing is most likely intact in OCD, and raise a novel, yet untested assumption regarding perceptual deficits in OCD. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

Multicenter Cell Processing for Cardiovascular Regenerative Medicine Applications - The Cardiovascular Cell Therapy Research Network (CCTRN) Experience

PubMed Central

Gee, Adrian P.; Richman, Sara; Durett, April; McKenna, David; Traverse, Jay; Henry, Timothy; Fisk, Diann; Pepine, Carl; Bloom, Jeannette; Willerson, James; Prater, Karen; Zhao, David; Koç, Jane Reese; Ellis, Steven; Taylor, Doris; Cogle, Christopher; Moyé, Lemuel; Simari, Robert; Skarlatos, Sonia

2013-01-01

Background Aims Multi-center cellular therapy clinical trials require the establishment and implementation of standardized cell processing protocols and associated quality control mechanisms. The aims here were to develop such an infrastructure in support of the Cardiovascular Cell Therapy Research Network (CCTRN) and to report on the results of processing for the first 60 patients. Methods Standardized cell preparations, consisting of autologous bone marrow mononuclear cells, prepared using the Sepax device were manufactured at each of the five processing facilities that supported the clinical treatment centers. Processing staff underwent centralized training that included proficiency evaluation. Quality was subsequently monitored by a central quality control program that included product evaluation by the CCTRN biorepositories. Results Data from the first 60 procedures demonstrate that uniform products, that met all release criteria, could be manufactured at all five sites within 7 hours of receipt of the bone marrow. Uniformity was facilitated by use of the automated systems (the Sepax for processing and the Endosafe device for endotoxin testing), standardized procedures and centralized quality control. Conclusions Complex multicenter cell therapy and regenerative medicine protocols can, where necessary, successfully utilize local processing facilities once an effective infrastructure is in place to provide training, and quality control. PMID:20524773

Image processing system performance prediction and product quality evaluation

NASA Technical Reports Server (NTRS)

Stein, E. K.; Hammill, H. B. (Principal Investigator)

1976-01-01

The author has identified the following significant results. A new technique for image processing system performance prediction and product quality evaluation was developed. It was entirely objective, quantitative, and general, and should prove useful in system design and quality control. The technique and its application to determination of quality control procedures for the Earth Resources Technology Satellite NASA Data Processing Facility are described.

The construction of control chart for PM10 functional data

NASA Astrophysics Data System (ADS)

Shaadan, Norshahida; Jemain, Abdul Aziz; Deni, Sayang Mohd

2014-06-01

In this paper, a statistical procedure to construct a control chart for monitoring air quality (PM10) using functional data is proposed. A set of daily indices that represent the daily PM10 curves were obtained using Functional Principal Component Analysis (FPCA). By means of an iterative charting procedure, a reference data set that represented a stable PM10 process was obtained. The data were then used as a reference for monitoring future data. The application of the procedure was conducted using seven-year (2004-2010) period of recorded data from the Klang air quality monitoring station located in the Klang Valley region of Peninsular Malaysia. The study showed that the control chart provided a useful visualization tool for monitoring air quality and was capable in detecting abnormality in the process system. As in the case of Klang station, the results showed that with reference to 2004-2008, the air quality (PM10) in 2010 was better than that in 2009.

Maximization of DRAM yield by control of surface charge and particle addition during high dose implantation

NASA Astrophysics Data System (ADS)

Horvath, J.; Moffatt, S.

1991-04-01

Ion implantation processing exposes semiconductor devices to an energetic ion beam in order to deposit dopant ions in shallow layers. In addition to this primary process, foreign materials are deposited as particles and surface films. The deposition of particles is a major cause of IC yield loss and becomes even more significant as device dimensions are decreased. Control of particle addition in a high-volume production environment requires procedures to limit beamline and endstation sources, control of particle transport, cleaning procedures and a well grounded preventative maintenance philosophy. Control of surface charge by optimization of the ion beam and electron shower conditions and measurement with a real-time charge sensor has been effective in improving the yield of NMOS and CMOS DRAMs. Control of surface voltages to a range between 0 and -20 V was correlated with good implant yield with PI9200 implanters for p + and n + source-drain implants.

The role of the supplementary motor area for speech and language processing.

PubMed

Hertrich, Ingo; Dietrich, Susanne; Ackermann, Hermann

2016-09-01

Apart from its function in speech motor control, the supplementary motor area (SMA) has largely been neglected in models of speech and language processing in the brain. The aim of this review paper is to summarize more recent work, suggesting that the SMA has various superordinate control functions during speech communication and language reception, which is particularly relevant in case of increased task demands. The SMA is subdivided into a posterior region serving predominantly motor-related functions (SMA proper) whereas the anterior part (pre-SMA) is involved in higher-order cognitive control mechanisms. In analogy to motor triggering functions of the SMA proper, the pre-SMA seems to manage procedural aspects of cognitive processing. These latter functions, among others, comprise attentional switching, ambiguity resolution, context integration, and coordination between procedural and declarative memory structures. Regarding language processing, this refers, for example, to the use of inner speech mechanisms during language encoding, but also to lexical disambiguation, syntax and prosody integration, and context-tracking. Copyright © 2016 Elsevier Ltd. All rights reserved.

Neotectonic control on drainage systems: GIS-based geomorphometric and morphotectonic assessment for Crete, Greece

NASA Astrophysics Data System (ADS)

Argyriou, Athanasios V.; Teeuw, Richard M.; Soupios, Pantelis; Sarris, Apostolos

2017-11-01

Geomorphic indices can be used to examine the geomorphological and tectonic processes responsible for the development of the drainage basins. Such indices can be dependent on tectonics, erosional processes and other factors that control the morphology of the landforms. The inter-relationships between geomorphic indices can determine the influence of regional tectonic activity in the shape development of drainage basins. A Multi-Criteria Decision Analysis (MCDA) procedure has been used to perform an integrated cluster analysis that highlights information associated with the dominant regional tectonic activity. Factor Analysis (FA) and Analytical Hierarchy Process (AHP) were considered within that procedure, producing a representation of the distributed regional tectonic activity of the drainage basins studied. The study area is western Crete, located in the outer fore-arc of the Hellenic subduction zone, one of the world's most tectonically active regions. The results indicate that in the landscape evolution of the study area (especially the western basins) tectonic controls dominate over lithological controls.

Autologous chondrocyte implantation for cartilage injury treatment in Chiang Mai University Hospital: a case report.

PubMed

Wongtriratanachai, Prasit; Pruksakorn, Dumnoensun; Pothacharoen, Peraphan; Nimkingratana, Puwapong; Pattamapaspong, Nuttaya; Phornphutkul, Chanakarn; Setsitthakun, Sasiwariya; Fongsatitkul, Ladda; Phrompaet, Sureeporn

2013-11-01

Autologous chondrocyte implantation (ACI) has become one of the standard procedures for articular cartilage defect treatment. This technique provides a promising result. However the procedural process requires an approach of several steps from multidisciplinary teams. Although the success of this procedure has been reported from Srinakharinvirot University since 2007, the application of ACI is still limited in Thailand due to the complexity of processes and stringent quality control. This report is to present the first case of the cartilage defect treatment using the first generation-ACI under Chiang Mai University's (CMU) own facility and Ethics Committee. This paper also reviews the process of biotechnology procedures, patient selection, surgical, and rehabilitation techniques. The success of the first case is an important milestone for the further development of the CMU Human Translational Research Laboratory in near future.

Integration for navigation on the UMASS mobile perception lab

NASA Technical Reports Server (NTRS)

Draper, Bruce; Fennema, Claude; Rochwerger, Benny; Riseman, Edward; Hanson, Allen

1994-01-01

Integration of real-time visual procedures for use on the Mobile Perception Lab (MPL) was presented. The MPL is an autonomous vehicle designed for testing visually guided behavior. Two critical areas of focus in the system design were data storage/exchange and process control. The Intermediate Symbolic Representation (ISR3) supported data storage and exchange, and the MPL script monitor provided process control. Resource allocation, inter-process communication, and real-time control are difficult problems which must be solved in order to construct strong autonomous systems.

Photographic consulting services to the Earth Resources program. [using aerial photography as a tool for scientific measurement

NASA Technical Reports Server (NTRS)

1976-01-01

The recommendations, procedures, and techniques are summarized which provided by the Kodak Apparatus Division to the Ames Research Center to support the Earth Resources Aircraft Program at that facility. Recommendations, procedures, and calibration data are included for sensitometry, densitometry, laboratory cleanliness, and determination of camera exposure. Additional comments are made regarding process control procedures and general laboratory operations.

Standards for the Analysis and Processing of Surface-Water Data and Information Using Electronic Methods

USGS Publications Warehouse

Sauer, Vernon B.

2002-01-01

Surface-water computation methods and procedures are described in this report to provide standards from which a completely automated electronic processing system can be developed. To the greatest extent possible, the traditional U. S. Geological Survey (USGS) methodology and standards for streamflow data collection and analysis have been incorporated into these standards. Although USGS methodology and standards are the basis for this report, the report is applicable to other organizations doing similar work. The proposed electronic processing system allows field measurement data, including data stored on automatic field recording devices and data recorded by the field hydrographer (a person who collects streamflow and other surface-water data) in electronic field notebooks, to be input easily and automatically. A user of the electronic processing system easily can monitor the incoming data and verify and edit the data, if necessary. Input of the computational procedures, rating curves, shift requirements, and other special methods are interactive processes between the user and the electronic processing system, with much of this processing being automatic. Special computation procedures are provided for complex stations such as velocity-index, slope, control structures, and unsteady-flow models, such as the Branch-Network Dynamic Flow Model (BRANCH). Navigation paths are designed to lead the user through the computational steps for each type of gaging station (stage-only, stagedischarge, velocity-index, slope, rate-of-change in stage, reservoir, tide, structure, and hydraulic model stations). The proposed electronic processing system emphasizes the use of interactive graphics to provide good visual tools for unit values editing, rating curve and shift analysis, hydrograph comparisons, data-estimation procedures, data review, and other needs. Documentation, review, finalization, and publication of records are provided for with the electronic processing system, as well as archiving, quality assurance, and quality control.

Controlling organic chemical hazards in food manufacturing: a hazard analysis critical control points (HACCP) approach.

PubMed

Ropkins, K; Beck, A J

2002-08-01

Hazard analysis by critical control points (HACCP) is a systematic approach to the identification, assessment and control of hazards. Effective HACCP requires the consideration of all hazards, i.e., chemical, microbiological and physical. However, to-date most 'in-place' HACCP procedures have tended to focus on the control of microbiological and physical food hazards. In general, the chemical component of HACCP procedures is either ignored or limited to applied chemicals, e.g., food additives and pesticides. In this paper we discuss the application of HACCP to a broader range of chemical hazards, using organic chemical contaminants as examples, and the problems that are likely to arise in the food manufacturing sector. Chemical HACCP procedures are likely to result in many of the advantages previously identified for microbiological HACCP procedures: more effective, efficient and economical than conventional end-point-testing methods. However, the high costs of analytical monitoring of chemical contaminants and a limited understanding of formulation and process optimisation as means of controlling chemical contamination of foods are likely to prevent chemical HACCP becoming as effective as microbiological HACCP.

Selecting Statistical Procedures for Quality Control Planning Based on Risk Management.

PubMed

Yago, Martín; Alcover, Silvia

2016-07-01

According to the traditional approach to statistical QC planning, the performance of QC procedures is assessed in terms of its probability of rejecting an analytical run that contains critical size errors (PEDC). Recently, the maximum expected increase in the number of unacceptable patient results reported during the presence of an undetected out-of-control error condition [Max E(NUF)], has been proposed as an alternative QC performance measure because it is more related to the current introduction of risk management concepts for QC planning in the clinical laboratory. We used a statistical model to investigate the relationship between PEDC and Max E(NUF) for simple QC procedures widely used in clinical laboratories and to construct charts relating Max E(NUF) with the capability of the analytical process that allow for QC planning based on the risk of harm to a patient due to the report of erroneous results. A QC procedure shows nearly the same Max E(NUF) value when used for controlling analytical processes with the same capability, and there is a close relationship between PEDC and Max E(NUF) for simple QC procedures; therefore, the value of PEDC can be estimated from the value of Max E(NUF) and vice versa. QC procedures selected by their high PEDC value are also characterized by a low value for Max E(NUF). The PEDC value can be used for estimating the probability of patient harm, allowing for the selection of appropriate QC procedures in QC planning based on risk management. © 2016 American Association for Clinical Chemistry.

21 CFR 820.75 - Process validation.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Process validation. 820.75 Section 820.75 Food and... QUALITY SYSTEM REGULATION Production and Process Controls § 820.75 Process validation. (a) Where the... validated with a high degree of assurance and approved according to established procedures. The validation...

21 CFR 820.75 - Process validation.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Process validation. 820.75 Section 820.75 Food and... QUALITY SYSTEM REGULATION Production and Process Controls § 820.75 Process validation. (a) Where the... validated with a high degree of assurance and approved according to established procedures. The validation...

21 CFR 820.75 - Process validation.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Process validation. 820.75 Section 820.75 Food and... QUALITY SYSTEM REGULATION Production and Process Controls § 820.75 Process validation. (a) Where the... validated with a high degree of assurance and approved according to established procedures. The validation...

21 CFR 820.75 - Process validation.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Process validation. 820.75 Section 820.75 Food and... QUALITY SYSTEM REGULATION Production and Process Controls § 820.75 Process validation. (a) Where the... validated with a high degree of assurance and approved according to established procedures. The validation...

21 CFR 820.75 - Process validation.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Process validation. 820.75 Section 820.75 Food and... QUALITY SYSTEM REGULATION Production and Process Controls § 820.75 Process validation. (a) Where the... validated with a high degree of assurance and approved according to established procedures. The validation...

7 CFR 58.928 - Quality control tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.928 Section 58.928... Procedures § 58.928 Quality control tests. All dairy products and other ingredients shall be subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be...

7 CFR 58.335 - Quality control tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.335 Section 58.335... Procedures § 58.335 Quality control tests. All milk, cream and related products are subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be made on flow...

Impact on Patient Safety and Satisfaction of Implementation of an Outpatient Clinic in Interventional Radiology (IPSIPOLI-Study): A Quasi-Experimental Prospective Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lutjeboer, Jacob, E-mail: j.lutjeboer@lumc.nl; Burgmans, Mark Christiaan, E-mail: m.c.burgmans@lumc.nl, E-mail: mburgmans@hotmail.com; Chung, Kaman, E-mail: kaman.chung10@gmail.com

PurposeInterventional radiology (IR) procedures are associated with high rates of preparation and planning errors. In many centers, pre-procedural consultation and screening of patients is performed by referring physicians. Interventional radiologists have better knowledge about procedure details and risks, but often only get acquainted with the patient in the procedure room. We hypothesized that patient safety (PS) and patient satisfaction (PSAT) in elective IR procedures would improve by implementation of a pre-procedural visit to an outpatient IR clinic.Material and MethodsIRB approval was obtained and informed consent was waived. PS and PSAT were measured in patients undergoing elective IR procedures before (controlmore » group; n = 110) and after (experimental group; n = 110) implementation of an outpatient IR clinic. PS was measured as the number of process deviations. PSAT was assessed using a questionnaire measuring Likert scores of three dimensions: interpersonal care aspects, information/communication, and patient participation. Differences in PS and PSAT between the two groups were compared using an independent t test.ResultsThe average number of process deviations per patient was 0.39 in the control group compared to 0.06 in the experimental group (p < 0.001). In 9.1 % patients in the control group, no legal informed consent was obtained compared to 0 % in the experimental group. The mean overall Likert score was significantly higher in the experimental group compared to the control group: 2.68 (SD 0.314) versus 2.48 (SD 0.381) (p < 0.001).ConclusionPS and PSAT improve significantly if patients receive consultation and screening in an IR outpatient clinic prior to elective IR procedures.« less

Quality control and assurance for validation of DOS/I measurements

NASA Astrophysics Data System (ADS)

Cerussi, Albert; Durkin, Amanda; Kwong, Richard; Quang, Timothy; Hill, Brian; Tromberg, Bruce J.; MacKinnon, Nick; Mantulin, William W.

2010-02-01

Ongoing multi-center clinical trials are crucial for Biophotonics to gain acceptance in medical imaging. In these trials, quality control (QC) and assurance (QA) are key to success and provide "data insurance". Quality control and assurance deal with standardization, validation, and compliance of procedures, materials and instrumentation. Specifically, QC/QA involves systematic assessment of testing materials, instrumentation performance, standard operating procedures, data logging, analysis, and reporting. QC and QA are important for FDA accreditation and acceptance by the clinical community. Our Biophotonics research in the Network for Translational Research in Optical Imaging (NTROI) program for breast cancer characterization focuses on QA/QC issues primarily related to the broadband Diffuse Optical Spectroscopy and Imaging (DOS/I) instrumentation, because this is an emerging technology with limited standardized QC/QA in place. In the multi-center trial environment, we implement QA/QC procedures: 1. Standardize and validate calibration standards and procedures. (DOS/I technology requires both frequency domain and spectral calibration procedures using tissue simulating phantoms and reflectance standards, respectively.) 2. Standardize and validate data acquisition, processing and visualization (optimize instrument software-EZDOS; centralize data processing) 3. Monitor, catalog and maintain instrument performance (document performance; modularize maintenance; integrate new technology) 4. Standardize and coordinate trial data entry (from individual sites) into centralized database 5. Monitor, audit and communicate all research procedures (database, teleconferences, training sessions) between participants ensuring "calibration". This manuscript describes our ongoing efforts, successes and challenges implementing these strategies.

Control of Risks Through the Use of Procedures: A Method for Evaluating the Change in Risk

NASA Technical Reports Server (NTRS)

Praino, Gregory T.; Sharit, Joseph

2010-01-01

This paper considers how procedures can be used to control risks faced by an organization and proposes a means of recognizing if a particular procedure reduces risk or contributes to the organization's exposure. The proposed method was developed out of the review of work documents and the governing procedures performed in the wake of the Columbia accident by NASA and the Space Shuttle prime contractor, United Space Alliance, LLC. A technique was needed to understand the rules, or procedural controls, in place at the time in the context of how important the role of each rule was. The proposed method assesses procedural risks, the residual risk associated with a hazard after a procedure's influence is accounted for, by considering each clause of a procedure as a unique procedural control that may be beneficial or harmful. For procedural risks with consequences severe enough to threaten the survival of the organization, the method measures the characteristics of each risk on a scale that is an alternative to the traditional consequence/likelihood couple. The dual benefits of the substitute scales are that they eliminate both the need to quantify a relationship between different consequence types and the need for the extensive history a probabilistic risk assessment would require. Control Value is used as an analog for the consequence, where the value of a rule is based on how well the control reduces the severity of the consequence when operating successfully. This value is composed of two parts: the inevitability of the consequence in the absence of the control, and the opportunity to intervene before the consequence is realized. High value controls will be ones where there is minimal need for intervention but maximum opportunity to actively prevent the outcome. Failure Likelihood is used as the substitute for the conventional likelihood of the outcome. For procedural controls, a failure is considered to be any non-malicious violation of the rule, whether intended or not. The model used for describing the Failure Likelihood considers how well a task was established by evaluating that task on five components. The components selected to define a well established task are: that it be defined, assigned to someone capable, that they be trained appropriately, that the actions be organized to enable proper completion and that some form of independent monitoring be performed. Validation of the method was based on the information provided by a group of experts in Space Shuttle ground processing when they were presented with 5 scenarios that identified a clause from a procedure. For each scenario, they recorded their perception of how important the associated rule was and how likely it was to fail. They then rated the components of Control Value and Failure Likelihood for all the scenarios. The order in which each reviewer ranked the scenarios Control Value and Failure Likelihood was compared to the order in which they ranked the scenarios for each of the associated components; inevitability and opportunity for Control Value and definition, assignment, training, organization and monitoring for Failure Likelihood. This order comparison showed how the components contributed to a relative relationship to the substitute risk element. With the relationship established for Space Shuttle ground processing, this method can be used to gauge if the introduction or removal of a particular rule will increase or decrease the .risk associated with the hazard it is intended to control.

76 FR 29767 - Preventive Controls for Registered Human Food and Animal Food/Feed Facilities; Request for Comments

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-23

... associated with specific types of food or specific methods of manufacturing, processing, packing, or holding... specific methods of manufacturing, processing, packing, or holding food. In particular, we welcome input on... controls (e.g., procedures and practices utilized to minimize the risk of contamination) for human food and...

32 CFR Appendix A to Part 223 - Procedures for Identifying and Controlling DoD UCNI

Code of Federal Regulations, 2011 CFR

2011-07-01

... security measures, including security plans, procedures, and equipment, for the physical protection of DoD... stand-alone personal computers, or shared-logic work processing systems, if protection from unauthorized... and security by increasing significantly the likelihood of the illegal production of nuclear weapons...

Fracture control procedures for aircraft structural integrity

NASA Technical Reports Server (NTRS)

Wood, H. A.

1972-01-01

The application of applied fracture mechanics in the design, analysis, and qualification of aircraft structural systems are reviewed. Recent service experiences are cited. Current trends in high-strength materials application are reviewed with particular emphasis on the manner in which fracture toughness and structural efficiency may affect the material selection process. General fracture control procedures are reviewed in depth with specific reference to the impact of inspectability, structural arrangement, and material on proposed analysis requirements for safe crack growth. The relative impact on allowable design stress is indicated by example. Design criteria, material, and analysis requirements for implementation of fracture control procedures are reviewed together with limitations in current available data techniques. A summary of items which require further study and attention is presented.

9 CFR 320.1 - Records required to be kept.

Code of Federal Regulations, 2010 CFR

2010-01-01

... processing procedures to destroy trichinae in § 318.10(c)(3)(iv) (Methods 5 and 6). (8) Records of nutrition... control of the production process using advanced meat/bone separation machinery and meat recovery systems...

"Congratulations, you have been randomized into the control group!(?)": issues to consider when recruiting schools for matched-pair randomized control trials of prevention programs.

PubMed

Ji, Peter; DuBois, David L; Flay, Brian R; Brechling, Vanessa

2008-03-01

Recruiting schools into a matched-pair randomized control trial (MP-RCT) to evaluate the efficacy of a school-level prevention program presents challenges for researchers. We considered which of 2 procedures would be most effective for recruiting schools into the study and assigning them to conditions. In 1 procedure (recruit and match/randomize), we would recruit schools and match them prior to randomization, and in the other (match/randomize and recruitment), we would match schools and randomize them prior to recruitment. We considered how each procedure impacted the randomization process and our ability to recruit schools into the study. After implementing the selected procedure, the equivalence of both treatment and control group schools and the participating and nonparticipating schools on school demographic variables was evaluated. We decided on the recruit and match/randomize procedure because we thought it would provide the opportunity to build rapport with the schools and prepare them for the randomization process, thereby increasing the likelihood that they would accept their randomly assigned conditions. Neither the treatment and control group schools nor the participating and nonparticipating schools exhibited statistically significant differences from each other on any of the school demographic variables. Recruitment of schools prior to matching and randomization in an MP-RCT may facilitate the recruitment of schools and thus enhance both the statistical power and the representativeness of study findings. Future research would benefit from the consideration of a broader range of variables (eg, readiness to implement a comprehensive prevention program) both in matching schools and in evaluating their representativeness to nonparticipating schools.

Assessing Subjectivity in Sensor Data Post Processing via a Controlled Experiment

NASA Astrophysics Data System (ADS)

Jones, A. S.; Horsburgh, J. S.; Eiriksson, D.

2017-12-01

Environmental data collected by in situ sensors must be reviewed to verify validity, and conducting quality control often requires making edits in post processing to generate approved datasets. This process involves decisions by technicians, data managers, or data users on how to handle problematic data. Options include: removing data from a series, retaining data with annotations, and altering data based on algorithms related to adjacent data points or the patterns of data at other locations or of other variables. Ideally, given the same dataset and the same quality control guidelines, multiple data quality control technicians would make the same decisions in data post processing. However, despite the development and implementation of guidelines aimed to ensure consistent quality control procedures, we have faced ambiguity when performing post processing, and we have noticed inconsistencies in the practices of individuals performing quality control post processing. Technicians with the same level of training and using the same input datasets may produce different results, affecting the overall quality and comparability of finished data products. Different results may also be produced by technicians that do not have the same level of training. In order to assess the effect of subjective decision making by the individual technician on the end data product, we designed an experiment where multiple users performed quality control post processing on the same datasets using a consistent set of guidelines, field notes, and tools. We also assessed the effect of technician experience and training by conducting the same procedures with a group of novices unfamiliar with the data and the quality control process and compared their results to those generated by a group of more experienced technicians. In this presentation, we report our observations of the degree of subjectivity in sensor data post processing, assessing and quantifying the impacts of individual technician as well as technician experience on quality controlled data products.

23 CFR 190.7 - Processing of claims.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Processing of claims. 190.7 Section 190.7 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PAYMENT PROCEDURES INCENTIVE PAYMENTS FOR CONTROLLING OUTDOOR ADVERTISING ON THE INTERSTATE SYSTEM § 190.7 Processing of claims. Audited and approved PR...

23 CFR 190.7 - Processing of claims.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 23 Highways 1 2014-04-01 2014-04-01 false Processing of claims. 190.7 Section 190.7 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PAYMENT PROCEDURES INCENTIVE PAYMENTS FOR CONTROLLING OUTDOOR ADVERTISING ON THE INTERSTATE SYSTEM § 190.7 Processing of claims. Audited and approved PR...

23 CFR 190.7 - Processing of claims.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 23 Highways 1 2011-04-01 2011-04-01 false Processing of claims. 190.7 Section 190.7 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PAYMENT PROCEDURES INCENTIVE PAYMENTS FOR CONTROLLING OUTDOOR ADVERTISING ON THE INTERSTATE SYSTEM § 190.7 Processing of claims. Audited and approved PR...

23 CFR 190.7 - Processing of claims.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 23 Highways 1 2013-04-01 2013-04-01 false Processing of claims. 190.7 Section 190.7 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PAYMENT PROCEDURES INCENTIVE PAYMENTS FOR CONTROLLING OUTDOOR ADVERTISING ON THE INTERSTATE SYSTEM § 190.7 Processing of claims. Audited and approved PR...

Space Transportation System Cargo projects: inertial stage/spacecraft integration plan. Volume 1: Management plan

NASA Technical Reports Server (NTRS)

1981-01-01

The Kennedy Space Center (KSC) Management System for the Inertial Upper Stage (IUS) - spacecraft processing from KSC arrival through launch is described. The roles and responsibilities of the agencies and test team organizations involved in IUS-S/C processing at KSC for non-Department of Defense missions are described. Working relationships are defined with respect to documentation preparation, coordination and approval, schedule development and maintenance, test conduct and control, configuration management, quality control and safety. The policy regarding the use of spacecraft contractor test procedures, IUS contractor detailed operating procedures and KSC operations and maintenance instructions is defined. Review and approval requirements for each documentation system are described.

Quality control developments for graphite/PMR15 polyimide composites materials

NASA Technical Reports Server (NTRS)

Sheppard, C. H.; Hoggatt, J. T.

1979-01-01

The problem of lot-to-lot and within-lot variability of graphite/PMR-15 prepreg was investigated. The PMR-15 chemical characterization data were evaluated along with the processing conditions controlling the manufacture of PMR-15 resin and monomers. Manufacturing procedures were selected to yield a consistently reproducible graphite prepreg that could be processed into acceptable structural elements.

[Nursing service certification. Norm UNE-EN-ISO 9001-2008].

PubMed

Salazar de la Guerra, R; Ferrer Arnedo, C; Labrador Domínguez, M J; Sangregorio Matesanz, A

2014-01-01

To certify the nursing services using a quality management system, taking an international standard as a reference, and based on a continuous improvement process. The standard was revised, and the Quality Management System documentation was updated, consisting of a Quality Manual and 7 control procedures. All the existing procedures were coded in accordance with the documentation control process. Each operational procedure was associated with a set of indicators which permitted to know the results obtained, analyze the deviations and to implement further improvements. The system was implemented successfully. Twenty-eight care procedures and eleven procedures concerning techniques were incorporated into the management system. Thirty indicators were established that allowed the whole process to be monitored. All patients were assigned to a nurse in their clinical notes and all of them had a personalized Care Plan according to planning methodology using North American Nursing Diagnosis Association (NANDA), Nursing Interventions Classification (NIC) and Nursing Outcomes Classification (NOC) international rankings. The incidence of falls, as well as the incidence of chronic skin wounds, was low, taking into account the characteristics of the patient and the duration of the stay (mean=35.87 days). The safety indicators had a high level of compliance, with 90% of patients clearly identified and 100% with hygiene protocol. The confidence rating given to the nurses was 91%. The certification enabled the quality of the service to be improved using a structured process, analyzing the results, dealing with non-conformities and introducing improvements. Copyright © 2014 SECA. Published by Elsevier Espana. All rights reserved.

Modernization of the automation control system of technological processes at the preparation plant in the conditions of technical re-equipment

NASA Astrophysics Data System (ADS)

Lyakhovets, M. V.; Wenger, K. G.; Myshlyaev, L. P.; Shipunov, M. V.; Grachev, V. V.; Melkozerov, M. Yu; Fairoshin, Sh A.

2018-05-01

The experience of modernization of the automation control system of technological processes at the preparation plant under the conditions of technical re-equipment of the preparation plant “Barzasskoye Tovarischestvo” LLC (Berezovsky) is considered. The automated process control systems (APCS), the modernization goals and the ways to achieve them are indicated, the main subsystems of the integrated APCS are presented, the enlarged functional and technical structure of the upgraded system is given. The procedure for commissioning an upgraded system is described.

Using AI Planning Techniques to Automatically Generate Image Processing Procedures: A Preliminary Report

NASA Technical Reports Server (NTRS)

Chien, S.

1994-01-01

This paper describes work on the Multimission VICAR Planner (MVP) system to automatically construct executable image processing procedures for custom image processing requests for the JPL Multimission Image Processing Lab (MIPL). This paper focuses on two issues. First, large search spaces caused by complex plans required the use of hand encoded control information. In order to address this in a manner similar to that used by human experts, MVP uses a decomposition-based planner to implement hierarchical/skeletal planning at the higher level and then uses a classical operator based planner to solve subproblems in contexts defined by the high-level decomposition.

Financial auditing at enterprises for control of projects realized with credit fund-raising

NASA Astrophysics Data System (ADS)

Lukmanova, Inessa

2017-10-01

The article analyzes methods of conducting financial audit under the construction control of projects implemented with raising credit funds in modern conditions. This work aims to improve the methodological toolkit of construction control when lending projects of the construction of transport infrastructure. The paper considers correlations of various procedures of construction control, financial audit and organizational and technical factors affecting investment and construction projects. The authors presented the logical scheme of the process of lending to legal entities and developed an algorithm of the procedure for conducting a financial audit, allowing to make possible adjustments and the right decision.

[Quality control in anesthesiology].

PubMed

Muñoz-Ramón, J M

1995-03-01

The process of quality control and auditing of anesthesiology allows us to evaluate care given by a service and solve problems that are detected. Quality control is a basic element of care giving and is only secondarily an area of academic research; it is therefore a meaningless effort if the information does not serve to improve departmental procedures. Quality assurance procedures assume certain infrastructural requirements and an initial period of implementation and adjustment. The main objectives of quality control are the reduction of morbidity and mortality due to anesthesia, assurance of the availability and proper management of resources and, finally, the well-being and safety of the patient.

23 CFR 630.1106 - Policy and procedures for work zone safety management.

Code of Federal Regulations, 2010 CFR

2010-04-01

... established in accordance with 23 CFR 630.1006, shall include the consideration and management of road user...; Exposure Control Measures to avoid or minimize worker exposure to motorized traffic and road user exposure... road users. (b) Agency processes, procedures, and/or guidance should be based on consideration of...

NHEXAS PHASE I ARIZONA STUDY--STANDARD OPERATING PROCEDURE FOR FORM QA/QC CHECKS (UA-C-2.0)

EPA Science Inventory

The purpose of this SOP is to outline the process of Field Quality Assurance and Quality Control checks. This procedure was followed to ensure consistent data retrieval during the Arizona NHEXAS project and the "Border" study. Keywords: custody; QA/QC; field checks.

The Nation...

77 FR 24873 - Modernization of Poultry Slaughter Inspection

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-26

... procedures, and that, at a minimum, these procedures include microbiological testing at pre-chill and post... required to collect pre-chill and post-chill to demonstrate process control; (2) presence of visible fecal...-chill and post-chill (77 FR 4428). The proposed rule provides for testing at pre-chill and post-chill...

The effects of type of knowledge upon human problem solving in a process control task

NASA Technical Reports Server (NTRS)

Morris, N. M.; Rouse, W. B.

1985-01-01

The question of what the operator of a dynamic system needs to know was investigated in an experiment using PLANT, a simulation of a generic dynamic production process. Knowledge of PLANT was manipulated via different types of instruction, so that four different groups were created: (1) minimal instructions only; (2) minimal instructions and guidelines for operation (procedures); (3) minimal instructions and dynamic relationships (principles); and (4) minimal instructions, and procedures, and principles. Subjects controlled PLANT in a variety of situations which required maintaining production while also diagnosing familiar and unfamiliar failures. Despite the fact that these manipulations resulted in differences in subjects' Knowledge, as assessed via a written test at the end of the experiment, instructions had no effect upon achievement of the primary goal of production, or upon subjects' ability to diagnose unfamiliar failures. However, those groups receiving procedures controlled the system in a more stable manner. Possible reasons for the failure to find an effect of principles are presented, and the implications of these results for operator training and aiding are discussed.

Bioreactor performance: a more scientific approach for practice.

PubMed

Lübbert, A; Bay Jørgensen, S

2001-02-13

In practice, the performance of a biochemical conversion process, i.e. the bioreactor performance, is essentially determined by the benefit/cost ratio. The benefit is generally defined in terms of the amount of the desired product produced and its market price. Cost reduction is the major objective in biochemical engineering. There are two essential engineering approaches to minimizing the cost of creating a particular product in an existing plant. One is to find a control path or operational procedure that optimally uses the dynamics of the process and copes with the many constraints restricting production. The other is to remove or lower the constraints by constructive improvements of the equipment and/or the microorganisms. This paper focuses on the first approach, dealing with optimization of the operational procedure and the measures by which one can ensure that the process adheres to the predetermined path. In practice, feedforward control is the predominant control mode applied. However, as it is frequently inadequate for optimal performance, feedback control may also be employed. Relevant aspects of such performance optimization are discussed.

Guidelines for Automatic Data Processing Physical Security and Risk Management. Federal Information Processing Standards Publication 31.

ERIC Educational Resources Information Center

National Bureau of Standards (DOC), Washington, DC.

These guidelines provide a handbook for use by federal organizations in structuring physical security and risk management programs for their automatic data processing facilities. This publication discusses security analysis, natural disasters, supporting utilities, system reliability, procedural measures and controls, off-site facilities,…

Artificial intelligence in process control: Knowledge base for the shuttle ECS model

NASA Technical Reports Server (NTRS)

Stiffler, A. Kent

1989-01-01

The general operation of KATE, an artificial intelligence controller, is outlined. A shuttle environmental control system (ECS) demonstration system for KATE is explained. The knowledge base model for this system is derived. An experimental test procedure is given to verify parameters in the model.

High level language for measurement complex control based on the computer E-100I

NASA Technical Reports Server (NTRS)

Zubkov, B. V.

1980-01-01

A high level language was designed to control the process of conducting an experiment using the computer "Elektrinika-1001". Program examples are given to control the measuring and actuating devices. The procedure of including these programs in the suggested high level language is described.

Influence of mechanical cell salvage on red blood cell aggregation, deformability, and 2,3-diphosphoglycerate in patients undergoing cardiac surgery with cardiopulmonary bypass.

PubMed

Gu, Y John; Vermeijden, Wytze J; de Vries, Adrianus J; Hagenaars, J Ans M; Graaff, Reindert; van Oeveren, Willem

2008-11-01

Mechanical cell salvage is increasingly used during cardiac surgery. Although this procedure is considered safe, it is unknown whether it affects the red blood cell (RBC) function, especially the RBC aggregation, deformability, and the contents of 2,3-diphosphoglycerate (2,3-DPG). This study examines the following: (1) whether the cell salvage procedure influences RBC function; and (2) whether retransfusion of the salvaged blood affects RBC function in patients. Forty patients undergoing cardiac surgery with cardiopulmonary bypass were randomly allocated to a cell saver group (n = 20) or a control group (n = 20). In the cell saver group, the blood aspirated from the wound area and the residual blood from the heart-lung machine were processed with a continuous-flow cell saver before retransfusion. In the control group this blood was retransfused without processing. The RBC aggregation and deformability were measured with a laser-assisted optical rotational cell analyzer and 2,3,-DPG by conventional laboratory test. The cell saver procedure did not influence the RBC aggregation but significantly reduced the RBC deformability (p = 0.007) and the content of RBC 2,3-DPG (p = 0.032). However, in patients receiving the processed blood, their intraoperative and postoperative RBC aggregation, deformability, and 2,3-DPG content did not differ from those of the control patients. Both groups of patients had a postoperative drop of RBC function as a result of hemodilution. The mechanical cell salvage procedure reduces the RBC deformability and the cell 2,3-DPG content. Retransfusion of the processed blood by cell saver does not further compromise the RBC function in patients undergoing cardiac surgery with cardiopulmonary bypass.

Modal control theory and application to aircraft lateral handling qualities design

NASA Technical Reports Server (NTRS)

Srinathkumar, S.

1978-01-01

A multivariable synthesis procedure based on eigenvalue/eigenvector assignment is reviewed and is employed to develop a systematic design procedure to meet the lateral handling qualities design objectives of a fighter aircraft over a wide range of flight conditions. The closed loop modal characterization developed provides significant insight into the design process and plays a pivotal role in the synthesis of robust feedback systems. The simplicity of the synthesis algorithm yields an efficient computer aided interactive design tool for flight control system synthesis.

Human Connectome Project Informatics: quality control, database services, and data visualization

PubMed Central

Marcus, Daniel S.; Harms, Michael P.; Snyder, Abraham Z.; Jenkinson, Mark; Wilson, J Anthony; Glasser, Matthew F.; Barch, Deanna M.; Archie, Kevin A.; Burgess, Gregory C.; Ramaratnam, Mohana; Hodge, Michael; Horton, William; Herrick, Rick; Olsen, Timothy; McKay, Michael; House, Matthew; Hileman, Michael; Reid, Erin; Harwell, John; Coalson, Timothy; Schindler, Jon; Elam, Jennifer S.; Curtiss, Sandra W.; Van Essen, David C.

2013-01-01

The Human Connectome Project (HCP) has developed protocols, standard operating and quality control procedures, and a suite of informatics tools to enable high throughput data collection, data sharing, automated data processing and analysis, and data mining and visualization. Quality control procedures include methods to maintain data collection consistency over time, to measure head motion, and to establish quantitative modality-specific overall quality assessments. Database services developed as customizations of the XNAT imaging informatics platform support both internal daily operations and open access data sharing. The Connectome Workbench visualization environment enables user interaction with HCP data and is increasingly integrated with the HCP's database services. Here we describe the current state of these procedures and tools and their application in the ongoing HCP study. PMID:23707591

Dissociation between controlled and automatic processes in the behavioral variant of fronto-temporal dementia.

PubMed

Collette, Fabienne; Van der Linden, Martial; Salmon, Eric

2010-01-01

A decline of cognitive functioning affecting several cognitive domains was frequently reported in patients with frontotemporal dementia. We were interested in determining if these deficits can be interpreted as reflecting an impairment of controlled cognitive processes by using an assessment tool specifically developed to explore the distinction between automatic and controlled processes, namely the process dissociation procedure (PDP) developed by Jacoby. The PDP was applied to a word stem completion task to determine the contribution of automatic and controlled processes to episodic memory performance and was administered to a group of 12 patients with the behavioral variant of frontotemporal dementia (bv-FTD) and 20 control subjects (CS). Bv-FTD patients obtained a lower performance than CS for the estimates of controlled processes, but no group differences was observed for estimates of automatic processes. The between-groups comparison of the estimates of controlled and automatic processes showed a larger contribution of automatic processes to performance in bv-FTD, while a slightly more important contribution of controlled processes was observed in control subjects. These results are clearly indicative of an alteration of controlled memory processes in bv-FTD.

Slice-thickness evaluation in CT and MRI: an alternative computerised procedure.

PubMed

Acri, G; Tripepi, M G; Causa, F; Testagrossa, B; Novario, R; Vermiglio, G

2012-04-01

The efficient use of computed tomography (CT) and magnetic resonance imaging (MRI) equipment necessitates establishing adequate quality-control (QC) procedures. In particular, the accuracy of slice thickness (ST) requires scan exploration of phantoms containing test objects (plane, cone or spiral). To simplify such procedures, a novel phantom and a computerised LabView-based procedure have been devised, enabling determination of full width at half maximum (FWHM) in real time. The phantom consists of a polymethyl methacrylate (PMMA) box, diagonally crossed by a PMMA septum dividing the box into two sections. The phantom images were acquired and processed using the LabView-based procedure. The LabView (LV) results were compared with those obtained by processing the same phantom images with commercial software, and the Fisher exact test (F test) was conducted on the resulting data sets to validate the proposed methodology. In all cases, there was no statistically significant variation between the two different procedures and the LV procedure, which can therefore be proposed as a valuable alternative to other commonly used procedures and be reliably used on any CT and MRI scanner.

Cognitive Fatigue Facilitates Procedural Sequence Learning.

PubMed

Borragán, Guillermo; Slama, Hichem; Destrebecqz, Arnaud; Peigneux, Philippe

2016-01-01

Enhanced procedural learning has been evidenced in conditions where cognitive control is diminished, including hypnosis, disruption of prefrontal activity and non-optimal time of the day. Another condition depleting the availability of controlled resources is cognitive fatigue (CF). We tested the hypothesis that CF, eventually leading to diminished cognitive control, facilitates procedural sequence learning. In a two-day experiment, 23 young healthy adults were administered a serial reaction time task (SRTT) following the induction of high or low levels of CF, in a counterbalanced order. CF was induced using the Time load Dual-back (TloadDback) paradigm, a dual working memory task that allows tailoring cognitive load levels to the individual's optimal performance capacity. In line with our hypothesis, reaction times (RT) in the SRTT were faster in the high- than in the low-level fatigue condition, and performance improvement was higher for the sequential than the motor components. Altogether, our results suggest a paradoxical, facilitating impact of CF on procedural motor sequence learning. We propose that facilitated learning in the high-level fatigue condition stems from a reduction in the cognitive resources devoted to cognitive control processes that normally oppose automatic procedural acquisition mechanisms.

Energy efficiency technologies in cement and steel industry

NASA Astrophysics Data System (ADS)

Zanoli, Silvia Maria; Cocchioni, Francesco; Pepe, Crescenzo

2018-02-01

In this paper, Advanced Process Control strategies aimed at energy efficiency achievement and improvement in cement and steel industry are proposed. A flexible and smart control structure constituted by several functional modules and blocks has been developed. The designed control strategy is based on Model Predictive Control techniques, formulated on linear models. Two industrial control solutions have been developed, oriented to energy efficiency and process control improvement in cement industry clinker rotary kilns (clinker production phase) and in steel industry billets reheating furnaces. Tailored customization procedures for the design of ad hoc control systems have been executed, based on the specific needs and specifications of the analysed processes. The installation of the developed controllers on cement and steel plants produced significant benefits in terms of process control which resulted in working closer to the imposed operating limits. With respect to the previous control systems, based on local controllers and/or operators manual conduction, more profitable configurations of the crucial process variables have been provided.

40 CFR 63.496 - Back-end process provisions-procedures to determine compliance using control or recovery devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... total organic HAP (or TOC, minus methane and ethane) emissions in all process vent streams and primary... TOC (minus methane and ethane) may be measured instead of total organic HAP. (C) The mass rates shall... and outlet of the control device shall be the sum of all total organic HAP (or TOC, minus methane and...

Processing of non-oxide ceramics from sol-gel methods

DOEpatents

Landingham, Richard; Reibold, Robert A.; Satcher, Joe

2014-12-12

A general procedure applied to a variety of sol-gel precursors and solvent systems for preparing and controlling homogeneous dispersions of very small particles within each other. Fine homogenous dispersions processed at elevated temperatures and controlled atmospheres make a ceramic powder to be consolidated into a component by standard commercial means: sinter, hot press, hot isostatic pressing (HIP), hot/cold extrusion, spark plasma sinter (SPS), etc.

AMO EXPRESS: A Command and Control Experiment for Crew Autonomy Onboard the International Space Station

NASA Technical Reports Server (NTRS)

Stetson, Howard K.; Frank, Jeremy; Cornelius, Randy; Haddock, Angie; Wang, Lui; Garner, Larry

2015-01-01

NASA is investigating a range of future human spaceflight missions, including both Mars-distance and Near Earth Object (NEO) targets. Of significant importance for these missions is the balance between crew autonomy and vehicle automation. As distance from Earth results in increasing communication delays, future crews need both the capability and authority to independently make decisions. However, small crews cannot take on all functions performed by ground today, and so vehicles must be more automated to reduce the crew workload for such missions. NASA's Advanced Exploration Systems Program funded Autonomous Mission Operations (AMO) project conducted an autonomous command and control experiment on-board the International Space Station that demonstrated single action intelligent procedures for crew command and control. The target problem was to enable crew initialization of a facility class rack with power and thermal interfaces, and involving core and payload command and telemetry processing, without support from ground controllers. This autonomous operations capability is enabling in scenarios such as initialization of a medical facility to respond to a crew medical emergency, and representative of other spacecraft autonomy challenges. The experiment was conducted using the Expedite the Processing of Experiments for Space Station (EXPRESS) rack 7, which was located in the Port 2 location within the U.S Laboratory onboard the International Space Station (ISS). Activation and deactivation of this facility is time consuming and operationally intensive, requiring coordination of three flight control positions, 47 nominal steps, 57 commands, 276 telemetry checks, and coordination of multiple ISS systems (both core and payload). Utilization of Draper Laboratory's Timeliner software, deployed on-board the ISS within the Command and Control (C&C) computers and the Payload computers, allowed development of the automated procedures specific to ISS without having to certify and employ novel software for procedure development and execution. The procedures contained the ground procedure logic and actions as possible to include fault detection and recovery capabilities.

POWER-ENHANCED MULTIPLE DECISION FUNCTIONS CONTROLLING FAMILY-WISE ERROR AND FALSE DISCOVERY RATES.

PubMed

Peña, Edsel A; Habiger, Joshua D; Wu, Wensong

2011-02-01

Improved procedures, in terms of smaller missed discovery rates (MDR), for performing multiple hypotheses testing with weak and strong control of the family-wise error rate (FWER) or the false discovery rate (FDR) are developed and studied. The improvement over existing procedures such as the Šidák procedure for FWER control and the Benjamini-Hochberg (BH) procedure for FDR control is achieved by exploiting possible differences in the powers of the individual tests. Results signal the need to take into account the powers of the individual tests and to have multiple hypotheses decision functions which are not limited to simply using the individual p -values, as is the case, for example, with the Šidák, Bonferroni, or BH procedures. They also enhance understanding of the role of the powers of individual tests, or more precisely the receiver operating characteristic (ROC) functions of decision processes, in the search for better multiple hypotheses testing procedures. A decision-theoretic framework is utilized, and through auxiliary randomizers the procedures could be used with discrete or mixed-type data or with rank-based nonparametric tests. This is in contrast to existing p -value based procedures whose theoretical validity is contingent on each of these p -value statistics being stochastically equal to or greater than a standard uniform variable under the null hypothesis. Proposed procedures are relevant in the analysis of high-dimensional "large M , small n " data sets arising in the natural, physical, medical, economic and social sciences, whose generation and creation is accelerated by advances in high-throughput technology, notably, but not limited to, microarray technology.

On the design of flight-deck procedures

NASA Technical Reports Server (NTRS)

Degani, Asaf; Wiener, Earl L.

1994-01-01

In complex human-machine systems, operations, training, and standardization depend on a elaborate set of procedures which are specified and mandated by the operational management of the organization. The intent is to provide guidance to the pilots, to ensure a logical, efficient, safe, and predictable means of carrying out the mission objectives. In this report the authors examine the issue of procedure use and design from a broad viewpoint. The authors recommend a process which we call 'The Four P's:' philosophy, policies, procedures, and practices. We believe that if an organization commits to this process, it can create a set of procedures that are more internally consistent, less confusing, better respected by the flight crews, and that will lead to greater conformity. The 'Four-P' model, and the guidelines for procedural development in appendix 1, resulted from cockpit observations, extensive interviews with airline management and pilots, interviews and discussion at one major airframe manufacturer, and an examination of accident and incident reports. Although this report is based on airline operations, we believe that the principles may be applicable to other complex, high-risk systems, such as nuclear power production, manufacturing process control, space flight, and military operations.

Age-related changes in the cerebral substrates of cognitive procedural learning.

PubMed

Hubert, Valérie; Beaunieux, Hélène; Chételat, Gaël; Platel, Hervé; Landeau, Brigitte; Viader, Fausto; Desgranges, Béatrice; Eustache, Francis

2009-04-01

Cognitive procedural learning occurs in three qualitatively different phases (cognitive, associative, and autonomous). At the beginning of this process, numerous cognitive functions are involved, subtended by distinct brain structures such as the prefrontal and parietal cortex and the cerebellum. As the learning progresses, these cognitive components are gradually replaced by psychomotor abilities, reflected by the increasing involvement of the cerebellum, thalamus, and occipital regions. In elderly subjects, although cognitive studies have revealed a learning effect, performance levels differ during the acquisition of a procedure. The effects of age on the learning of a cognitive procedure have not yet been examined using functional imaging. The aim of this study was therefore to characterize the cerebral substrates involved in the learning of a cognitive procedure, comparing a group of older subjects with young controls. For this purpose, we performed a positron emission tomography activation study using the Tower of Toronto task. A direct comparison of the two groups revealed the involvement of a similar network of brain regions at the beginning of learning (cognitive phase). However, the engagement of frontal and cingulate regions persisted in the older group as learning continued, whereas it ceased in the younger controls. We assume that this additional activation in the older group during the associative and autonomous phases reflected compensatory processes and the fact that some older subjects failed to fully automate the procedure. 2008 Wiley-Liss, Inc.

11 CFR 9405.5 - Categories of exemptions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... descriptions of manufacturing process, quality control methodology, and test results. The following procedures... lawful national security intelligence investigation, information furnished by a confidential source; (v...

11 CFR 9405.5 - Categories of exemptions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... descriptions of manufacturing process, quality control methodology, and test results. The following procedures... lawful national security intelligence investigation, information furnished by a confidential source; (v...

11 CFR 9405.5 - Categories of exemptions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... descriptions of manufacturing process, quality control methodology, and test results. The following procedures... lawful national security intelligence investigation, information furnished by a confidential source; (v...

11 CFR 9405.5 - Categories of exemptions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... descriptions of manufacturing process, quality control methodology, and test results. The following procedures... lawful national security intelligence investigation, information furnished by a confidential source; (v...

Computation of output feedback gains for linear stochastic systems using the Zangwill-Powell method

NASA Technical Reports Server (NTRS)

Kaufman, H.

1977-01-01

Because conventional optimal linear regulator theory results in a controller which requires the capability of measuring and/or estimating the entire state vector, it is of interest to consider procedures for computing controls which are restricted to be linear feedback functions of a lower dimensional output vector and which take into account the presence of measurement noise and process uncertainty. To this effect a stochastic linear model has been developed that accounts for process parameter and initial uncertainty, measurement noise, and a restricted number of measurable outputs. Optimization with respect to the corresponding output feedback gains was then performed for both finite and infinite time performance indices without gradient computation by using Zangwill's modification of a procedure originally proposed by Powell.

WE-G-BRA-06: Application of Systems and Control Theory-Based Hazard Analysis to Radiotherapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pawlicki, T; Samost, A; Leveson, N

Purpose: The process of delivering radiation occurs in a complex socio-technical system heavily reliant on human operators. Furthermore, both humans and software are notoriously challenging to account for in traditional hazard analysis models. High reliability industries such as aviation have approached this problem through using hazard analysis techniques grounded in systems and control theory. The purpose of this work is to apply the Systems Theoretic Accident Model Processes (STAMP) hazard model to radiotherapy. In particular, the System-Theoretic Process Analysis (STPA) approach is used to perform a hazard analysis of a proposed on-line adaptive cranial radiosurgery procedure that omits the CTmore » Simulation step and uses only CBCT for planning, localization, and treatment. Methods: The STPA procedure first requires the definition of high-level accidents and hazards leading to those accidents. From there, hierarchical control structures were created followed by the identification and description of control actions for each control structure. Utilizing these control structures, unsafe states of each control action were created. Scenarios contributing to unsafe control action states were then identified and translated into system requirements to constrain process behavior within safe boundaries. Results: Ten control structures were created for this new CBCT-only process which covered the areas of hospital and department management, treatment design and delivery, and vendor service. Twenty three control actions were identified that contributed to over 80 unsafe states of those control actions resulting in over 220 failure scenarios. Conclusion: The interaction of people, hardware, and software are highlighted through the STPA approach. STPA provides a hierarchical model for understanding the role of management decisions in impacting system safety so that a process design requirement can be traced back to the hazard and accident that it is intended to mitigate. Varian Medical Systems, Inc.« less

PROCRU: A model for analyzing crew procedures in approach to landing

NASA Technical Reports Server (NTRS)

Baron, S.; Muralidharan, R.; Lancraft, R.; Zacharias, G.

1980-01-01

A model for analyzing crew procedures in approach to landing is developed. The model employs the information processing structure used in the optimal control model and in recent models for monitoring and failure detection. Mechanisms are added to this basic structure to model crew decision making in this multi task environment. Decisions are based on probability assessments and potential mission impact (or gain). Sub models for procedural activities are included. The model distinguishes among external visual, instrument visual, and auditory sources of information. The external visual scene perception models incorporate limitations in obtaining information. The auditory information channel contains a buffer to allow for storage in memory until that information can be processed.

Dosimetry procedures for an industrial irradiation plant

NASA Astrophysics Data System (ADS)

Grahn, Ch.

Accurate and reliable dosimetry procedures constitute a very important part of process control and quality assurance at a radiation processing plant. γ-Dose measurements were made on the GBS 84 irradiator for food and other products on pallets or in containers. Chemical dosimeters wre exposed in the facility under conditions of the typical plant operation. The choice of the dosimeter systems employed was based on the experience in chemical dosimetry gained over several years. Dose uniformity information was obtained in air, spices, bulbs, feeds, cosmetics, plastics and surgical goods. Most products currently irradiated require dose uniformity which can be efficiently provided by pallet or box irradiators like GBS 84. The radiation performance characteristics and some dosimetry procedures are discussed.

40 CFR 63.8005 - What requirements apply to my process vessels?

Code of Federal Regulations, 2011 CFR

2011-07-01

... condensers, as defined in § 63.1251, are not considered to be control devices for process vessels. (d... vessels. (2) For the initial compliance demonstration for condensers, you must determine uncontrolled... process condenser is properly operated according to the procedures specified in § 63.1257(d)(2)(i)(C)(4...

78 FR 47701 - Agency Information Collection Activities; Proposed Collection; Comment Request; Procedures for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-06

... Fishery Products--21 CFR Part 123 (OMB Control Number 0910-0354)-- Extension FDA regulations in part 123 (21 CFR part 123) mandate the application of hazard analysis and critical control point (HACCP) principles to the processing of seafood. HACCP is a preventive system of hazard control designed to help...

75 FR 18211 - Agency Information Collection Activities; Proposed Collection; Comment Request; Procedures for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-09

... Importing of Fish and Fishery Products--21 CFR Part 123 (OMB Control Number 0910-0354)-- Extension FDA regulations in part 123 (21 CFR part 123) mandate the application of hazard analysis and critical control point (HACCP) principles to the processing of seafood. HACCP is a preventive system of hazard control...

40 CFR 1051.345 - What production-line testing records must I send to EPA?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES Testing Production-Line Vehicles and Engines § 1051.345 What production-line testing records must I send to EPA? (a.... We have not changed production processes or quality-control procedures for test engines (or vehicles...

40 CFR 1051.345 - What production-line testing records must I send to EPA?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES Testing Production-Line Vehicles and Engines § 1051.345 What production-line testing records must I send to EPA? (a.... We have not changed production processes or quality-control procedures for test engines (or vehicles...

40 CFR 1051.345 - What production-line testing records must I send to EPA?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES Testing Production-Line Vehicles and Engines § 1051.345 What production-line testing records must I send to EPA? (a.... We have not changed production processes or quality-control procedures for test engines (or vehicles...

40 CFR 1051.345 - What production-line testing records must I send to EPA?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES Testing Production-Line Vehicles and Engines § 1051.345 What production-line testing records must I send to EPA? (a.... We have not changed production processes or quality-control procedures for test engines (or vehicles...

40 CFR 1051.345 - What production-line testing records must I send to EPA?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES Testing Production-Line Vehicles and Engines § 1051.345 What production-line testing records must I send to EPA? (a.... We have not changed production processes or quality-control procedures for test engines (or vehicles...

Internal quality control: planning and implementation strategies.

PubMed

Westgard, James O

2003-11-01

The first essential in setting up internal quality control (IQC) of a test procedure in the clinical laboratory is to select the proper IQC procedure to implement, i.e. choosing the statistical criteria or control rules, and the number of control measurements, according to the quality required for the test and the observed performance of the method. Then the right IQC procedure must be properly implemented. This review focuses on strategies for planning and implementing IQC procedures in order to improve the quality of the IQC. A quantitative planning process is described that can be implemented with graphical tools such as power function or critical-error graphs and charts of operating specifications. Finally, a total QC strategy is formulated to minimize cost and maximize quality. A general strategy for IQC implementation is recommended that employs a three-stage design in which the first stage provides high error detection, the second stage low false rejection and the third stage prescribes the length of the analytical run, making use of an algorithm involving the average of normal patients' data.

Process Analytical Technology (PAT): batch-to-batch reproducibility of fermentation processes by robust process operational design and control.

PubMed

Gnoth, S; Jenzsch, M; Simutis, R; Lübbert, A

2007-10-31

The Process Analytical Technology (PAT) initiative of the FDA is a reaction on the increasing discrepancy between current possibilities in process supervision and control of pharmaceutical production processes and its current application in industrial manufacturing processes. With rigid approval practices based on standard operational procedures, adaptations of production reactors towards the state of the art were more or less inhibited for long years. Now PAT paves the way for continuous process and product improvements through improved process supervision based on knowledge-based data analysis, "Quality-by-Design"-concepts, and, finally, through feedback control. Examples of up-to-date implementations of this concept are presented. They are taken from one key group of processes in recombinant pharmaceutical protein manufacturing, the cultivations of genetically modified Escherichia coli bacteria.

25 CFR 542.22 - What are the minimum internal control standards for internal audit for Tier A gaming operations?

Code of Federal Regulations, 2010 CFR

2010-04-01

... but not limited to, bingo card control, payout procedures, and cash reconciliation process; (ii) Pull... 25 Indians 2 2010-04-01 2010-04-01 false What are the minimum internal control standards for... COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN SERVICES MINIMUM INTERNAL CONTROL STANDARDS § 542.22 What are...

25 CFR 542.32 - What are the minimum internal control standards for internal audit for Tier B gaming operations?

Code of Federal Regulations, 2010 CFR

2010-04-01

... but not limited to, bingo card control, payout procedures, and cash reconciliation process; (ii) Pull... 25 Indians 2 2010-04-01 2010-04-01 false What are the minimum internal control standards for... COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN SERVICES MINIMUM INTERNAL CONTROL STANDARDS § 542.32 What are...

Markov Chains For Testing Redundant Software

NASA Technical Reports Server (NTRS)

White, Allan L.; Sjogren, Jon A.

1990-01-01

Preliminary design developed for validation experiment that addresses problems unique to assuring extremely high quality of multiple-version programs in process-control software. Approach takes into account inertia of controlled system in sense it takes more than one failure of control program to cause controlled system to fail. Verification procedure consists of two steps: experimentation (numerical simulation) and computation, with Markov model for each step.

Automatic processing influences free recall: converging evidence from the process dissociation procedure and remember-know judgments.

PubMed

McCabe, David P; Roediger, Henry L; Karpicke, Jeffrey D

2011-04-01

Dual-process theories of retrieval suggest that controlled and automatic processing contribute to memory performance. Free recall tests are often considered pure measures of recollection, assessing only the controlled process. We report two experiments demonstrating that automatic processes also influence free recall. Experiment 1 used inclusion and exclusion tasks to estimate recollection and automaticity in free recall, adopting a new variant of the process dissociation procedure. Dividing attention during study selectively reduced the recollection estimate but did not affect the automatic component. In Experiment 2, we replicated the results of Experiment 1, and subjects additionally reported remember-know-guess judgments during recall in the inclusion condition. In the latter task, dividing attention during study reduced remember judgments for studied items, but know responses were unaffected. Results from both methods indicated that free recall is partly driven by automatic processes. Thus, we conclude that retrieval in free recall tests is not driven solely by conscious recollection (or remembering) but also by automatic influences of the same sort believed to drive priming on implicit memory tests. Sometimes items come to mind without volition in free recall.

A Proven Method for Meeting Export Control Objectives in Postal and Shipping Sectors

DTIC Science & Technology

2015-02-01

months, the USPIS team developed and implemented an export screening standard operating procedure, implemented new and updated processes and systems ...support and protect the U.S. Postal Service and its employees, infrastructure, and customers; enforce the laws that defend the nation’s mail system ...the incidence of mail shipments violating export control laws, regulations, and standards . • Evaluate current processes and systems and identify

Optimal Synthesis of Compliant Mechanisms using Subdivision and Commercial FEA (DETC2004-57497)

NASA Technical Reports Server (NTRS)

Hull, Patrick V.; Canfield, Stephen

2004-01-01

The field of distributed-compliance mechanisms has seen significant work in developing suitable topology optimization tools for their design. These optimal design tools have grown out of the techniques of structural optimization. This paper will build on the previous work in topology optimization and compliant mechanism design by proposing an alternative design space parameterization through control points and adding another step to the process, that of subdivision. The control points allow a specific design to be represented as a solid model during the optimization process. The process of subdivision creates an additional number of control points that help smooth the surface (for example a C(sup 2) continuous surface depending on the method of subdivision chosen) creating a manufacturable design free of some traditional numerical instabilities. Note that these additional control points do not add to the number of design parameters. This alternative parameterization and description as a solid model effectively and completely separates the design variables from the analysis variables during the optimization procedure. The motivation behind this work is to create an automated design tool from task definition to functional prototype created on a CNC or rapid-prototype machine. This paper will describe the proposed compliant mechanism design process and will demonstrate the procedure on several examples common in the literature.

Understanding and Controlling Cost in Total Joint Arthroplasty.

PubMed

Alvarado, Carlos M; Bosco, Joseph

2015-06-01

Total joint arthrosplasty (TJA) is both a commonly performed successful intervention and an expensive procedure.As our population ages, the expense of these interventions is expected to grow and hence its impact on healthcare costs will also grow. To ensure that TJA is available to all those who would benefit, it is incumbent that healthcare providers control the cost of these procedures. As orthopaedic surgeons, we must be at the forefront of this effort. The purpose of this review is to outline strategies to control or even decrease TJA cost without negatively affecting outcomes.This concept is at the center of value-based medicine and must guide our decision-making processes.

Enhanced job control language procedures for the SIMSYS2D two-dimensional water-quality simulation system

USGS Publications Warehouse

Karavitis, G.A.

1984-01-01

The SIMSYS2D two-dimensional water-quality simulation system is a large-scale digital modeling software system used to simulate flow and transport of solutes in freshwater and estuarine environments. Due to the size, processing requirements, and complexity of the system, there is a need to easily move the system and its associated files between computer sites when required. A series of job control language (JCL) procedures was written to allow transferability between IBM and IBM-compatible computers. (USGS)

Dynamics of the cognitive procedural learning in alcoholics with Korsakoff's syndrome.

PubMed

Beaunieux, Hélène; Pitel, Anne L; Witkowski, Thomas; Vabret, François; Viader, Fausto; Eustache, Francis

2013-06-01

While procedures acquired before the development of amnesia are likely to be preserved in alcoholic patients with Korsakoff's syndrome, the ability of Korsakoff patients (KS) to learn new cognitive procedures is called in question. According to the Adaptive Control of Thoughts model, learning a new cognitive procedure requires highly controlled processes in the initial cognitive phase, which may be difficult for KS with episodic and working memory deficits. The goals of the present study were to examine the learning dynamics of KS compared with uncomplicated alcoholic patients (AL) and control subjects (CS) and to determine the contribution of episodic and working memory abilities in cognitive procedural learning performance. Fourteen KS, 15 AL, and 15 CS were submitted to 40 trials (4 daily learning sessions) of the Tower of Toronto task (disk-transfer task similar to the tower of Hanoi task) as well as episodic and working memory tasks. The 10 KS who were able to perform the cognitive procedural learning task obtained lower results than both CS and AL. The cognitive phase was longer in the Korsakoff's syndrome group than in the other 2 groups but did not differ between the 3 groups any more when episodic memory abilities were controlled. Our results indicate that KS have impaired cognitive procedural learning abilities compared with both AL and CS. Episodic memory deficits observed in KS result in a delayed transition from the cognitive learning phase to more advanced learning phases and, as a consequence, in an absence of automation of the procedure within 40 trials. Copyright © 2012 by the Research Society on Alcoholism.

U.S.-MEXICO BORDER PROGRAM ARIZONA BORDER STUDY--STANDARD OPERATING PROCEDURE FOR FORM QA AND QC CHECKS (UA-C-2.0)

EPA Science Inventory

The purpose of this SOP is to outline the process of field quality assurance and quality control checks. This procedure was followed to ensure consistent data retrieval during the Arizona NHEXAS project and the Border study. Keywords: custody; QA/QC; field checks.

The U.S.-Mex...

[Generalization of money-handling though training in equivalence relationships].

PubMed

Vives-Montero, Carmen; Valero-Aguayo, Luis; Ascanio, Lourdes

2011-02-01

This research used a matching-to-sample procedure and equivalence learning process with language and verbal tasks. In the study, an application of the equivalence relationship of money was used with several kinds of euro coins presented. The sample consisted of 16 children (8 in the experimental group and 8 in the control group) aged 5 years. The prerequisite behaviors, the identification of coins and the practical use of different euro coins, were assessed in the pre and post phases for both groups. The children in the experimental group performed an equivalence task using the matching-to-sample procedure. This consisted of a stimulus sample and four matching stimuli, using a series of euro coins with equivalent value in each set. The children in the control group did not undergo this training process. The results showed a large variability in the children's data of the equivalence tests. The experimental group showed the greatest pre and post changes in the statistically significant data. They also showed a greater generalization in the identification of money and in the use of euro coins than the control group. The implications for educational training and the characteristics of the procedure used here for coin equivalence are discussed.

SSS-A attitude control prelaunch analysis and operations plan

NASA Technical Reports Server (NTRS)

Werking, R. D.; Beck, J.; Gardner, D.; Moyer, P.; Plett, M.

1971-01-01

A description of the attitude control support being supplied by the Mission and Data Operations Directorate is presented. Descriptions of the computer programs being used to support the mission for attitude determination, prediction, control, and definitive attitude processing are included. In addition, descriptions of the operating procedures which will be used to accomplish mission objectives are provided.

40 CFR 1054.345 - What production-line testing records must I send to EPA?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, SMALL NONROAD SPARK-IGNITION ENGINES AND... 1054. We have not changed production processes or quality-control procedures for test engines in a way...) Describe any facility used to test production-line engines and state its location. (2) State the total U.S...

40 CFR 1054.345 - What production-line testing records must I send to EPA?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, SMALL NONROAD SPARK-IGNITION ENGINES AND... 1054. We have not changed production processes or quality-control procedures for test engines in a way...) Describe any facility used to test production-line engines and state its location. (2) State the total U.S...

40 CFR 1054.345 - What production-line testing records must I send to EPA?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, SMALL NONROAD SPARK-IGNITION ENGINES AND... 1054. We have not changed production processes or quality-control procedures for test engines in a way...) Describe any facility used to test production-line engines and state its location. (2) State the total U.S...

40 CFR 1054.345 - What production-line testing records must I send to EPA?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, SMALL NONROAD SPARK-IGNITION ENGINES AND... 1054. We have not changed production processes or quality-control procedures for test engines in a way...) Describe any facility used to test production-line engines and state its location. (2) State the total U.S...

40 CFR 1054.345 - What production-line testing records must I send to EPA?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, SMALL NONROAD SPARK-IGNITION ENGINES AND... 1054. We have not changed production processes or quality-control procedures for test engines in a way...) Describe any facility used to test production-line engines and state its location. (2) State the total U.S...

40 CFR 63.1413 - Compliance demonstration procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... liquids, other than fuels, received by the control device. (i) For a scrubber, the design evaluation shall... scrubbing liquid. The design evaluation shall establish the design exhaust vent stream organic compound... process vent and the overall percent reduction for the collection of non-reactor batch process vents...

Process for producing astatine-211 for radiopharmaceutical use

DOEpatents

Mirzadeh, S.; Lambrecht, R.M.

1984-04-10

A process is described for reliably and consistently producing astatine-211 in small controlled volumes of a solution, which is selected from a choice of solvents that are useful in selected radiopharmaceutical procedures in which the At-211 activities are to be applied. 4 figures, 1 table.

38 CFR 36.4348 - Servicer Appraisal Processing Program.

Code of Federal Regulations, 2012 CFR

2012-07-01

... requirement, routine reviews of SAPP cases will be made by VA staff based upon quality control procedures..., that its activities do not deviate from high standards of integrity. The quality control system must include frequent, periodic audits that specifically address the appraisal review activity. These audits...

38 CFR 36.4348 - Servicer Appraisal Processing Program.

Code of Federal Regulations, 2014 CFR

2014-07-01

... requirement, routine reviews of SAPP cases will be made by VA staff based upon quality control procedures..., that its activities do not deviate from high standards of integrity. The quality control system must include frequent, periodic audits that specifically address the appraisal review activity. These audits...

38 CFR 36.4348 - Servicer Appraisal Processing Program.

Code of Federal Regulations, 2013 CFR

2013-07-01

... requirement, routine reviews of SAPP cases will be made by VA staff based upon quality control procedures..., that its activities do not deviate from high standards of integrity. The quality control system must include frequent, periodic audits that specifically address the appraisal review activity. These audits...

38 CFR 36.4348 - Servicer Appraisal Processing Program.

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirement, routine reviews of SAPP cases will be made by VA staff based upon quality control procedures..., that its activities do not deviate from high standards of integrity. The quality control system must include frequent, periodic audits that specifically address the appraisal review activity. These audits...

9 CFR 417.1 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE REGULATORY REQUIREMENTS UNDER THE FEDERAL MEAT INSPECTION ACT AND THE POULTRY PRODUCTS INSPECTION ACT HAZARD ANALYSIS AND... control point. A point, step, or procedure in a food process at which control can be applied and, as a...

9 CFR 417.1 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE REGULATORY REQUIREMENTS UNDER THE FEDERAL MEAT INSPECTION ACT AND THE POULTRY PRODUCTS INSPECTION ACT HAZARD ANALYSIS AND... control point. A point, step, or procedure in a food process at which control can be applied and, as a...

9 CFR 417.1 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE REGULATORY REQUIREMENTS UNDER THE FEDERAL MEAT INSPECTION ACT AND THE POULTRY PRODUCTS INSPECTION ACT HAZARD ANALYSIS AND... control point. A point, step, or procedure in a food process at which control can be applied and, as a...

9 CFR 417.1 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE REGULATORY REQUIREMENTS UNDER THE FEDERAL MEAT INSPECTION ACT AND THE POULTRY PRODUCTS INSPECTION ACT HAZARD ANALYSIS AND... control point. A point, step, or procedure in a food process at which control can be applied and, as a...

9 CFR 417.1 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE REGULATORY REQUIREMENTS UNDER THE FEDERAL MEAT INSPECTION ACT AND THE POULTRY PRODUCTS INSPECTION ACT HAZARD ANALYSIS AND... control point. A point, step, or procedure in a food process at which control can be applied and, as a...

Food safety and nutritional quality for the prevention of non communicable diseases: the Nutrient, hazard Analysis and Critical Control Point process (NACCP).

PubMed

Di Renzo, Laura; Colica, Carmen; Carraro, Alberto; Cenci Goga, Beniamino; Marsella, Luigi Tonino; Botta, Roberto; Colombo, Maria Laura; Gratteri, Santo; Chang, Ting Fa Margherita; Droli, Maurizio; Sarlo, Francesca; De Lorenzo, Antonino

2015-04-23

The important role of food and nutrition in public health is being increasingly recognized as crucial for its potential impact on health-related quality of life and the economy, both at the societal and individual levels. The prevalence of non-communicable diseases calls for a reformulation of our view of food. The Hazard Analysis and Critical Control Point (HACCP) system, first implemented in the EU with the Directive 43/93/CEE, later replaced by Regulation CE 178/2002 and Regulation CE 852/2004, is the internationally agreed approach for food safety control. Our aim is to develop a new procedure for the assessment of the Nutrient, hazard Analysis and Critical Control Point (NACCP) process, for total quality management (TMQ), and optimize nutritional levels. NACCP was based on four general principles: i) guarantee of health maintenance; ii) evaluate and assure the nutritional quality of food and TMQ; iii) give correct information to the consumers; iv) ensure an ethical profit. There are three stages for the application of the NACCP process: 1) application of NACCP for quality principles; 2) application of NACCP for health principals; 3) implementation of the NACCP process. The actions are: 1) identification of nutritional markers, which must remain intact throughout the food supply chain; 2) identification of critical control points which must monitored in order to minimize the likelihood of a reduction in quality; 3) establishment of critical limits to maintain adequate levels of nutrient; 4) establishment, and implementation of effective monitoring procedures of critical control points; 5) establishment of corrective actions; 6) identification of metabolic biomarkers; 7) evaluation of the effects of food intake, through the application of specific clinical trials; 8) establishment of procedures for consumer information; 9) implementation of the Health claim Regulation EU 1924/2006; 10) starting a training program. We calculate the risk assessment as follows: Risk (R) = probability (P) × damage (D). The NACCP process considers the entire food supply chain "from farm to consumer"; in each point of the chain it is necessary implement a tight monitoring in order to guarantee optimal nutritional quality.

Controlled and implicit processes in evaluative conditioning on implicit and explicit attitudes toward alcohol and intentions to drink.

PubMed

Zerhouni, Oulmann; Bègue, Laurent; Comiran, Francisco; Wiers, Reinout W

2018-01-01

Since implicit attitudes (i.e. evaluations occurring outside of complete awareness) are highly predictive of alcohol consumption, we tested an evaluative learning procedure based on repeated pairing to a critical stimulus (i.e. alcohol, the CS) with a valenced stimulus (the US) in order to modify implicit attitudes (i.e. evaluative conditioning; EC). We hypothesized that manipulating the learning context to bolster implicit affect misattribution should strengthen EC effects on implicit attitudes toward alcohol, while encouraging deliberate processing of CS-US pairs, should strengthen EC effects on explicit attitudes. In our study (n=114 students) we manipulated whether CS-US pairs were presented simultaneously or sequentially. Recollective memory was estimated with a Process Dissociation Procedure. Both implicit and explicit attitudes were assessed immediately after the procedure. Behavioral intentions were measured directly after and one week after the EC-procedure. We found that EC with sequential presentation had a stronger impact on implicit and explicit measures and on purchase intentions immediately after the procedure and one week after. The present findings provide new evidence that (i) EC is an effective way to change implicit attitudes toward alcohol and (ii) evidence that EC may be better described by propositional rather than dual process accounts. Copyright © 2017 Elsevier Ltd. All rights reserved.

Test/score/report: Simulation techniques for automating the test process

NASA Technical Reports Server (NTRS)

Hageman, Barbara H.; Sigman, Clayton B.; Koslosky, John T.

1994-01-01

A Test/Score/Report capability is currently being developed for the Transportable Payload Operations Control Center (TPOCC) Advanced Spacecraft Simulator (TASS) system which will automate testing of the Goddard Space Flight Center (GSFC) Payload Operations Control Center (POCC) and Mission Operations Center (MOC) software in three areas: telemetry decommutation, spacecraft command processing, and spacecraft memory load and dump processing. Automated computer control of the acceptance test process is one of the primary goals of a test team. With the proper simulation tools and user interface, the task of acceptance testing, regression testing, and repeatability of specific test procedures of a ground data system can be a simpler task. Ideally, the goal for complete automation would be to plug the operational deliverable into the simulator, press the start button, execute the test procedure, accumulate and analyze the data, score the results, and report the results to the test team along with a go/no recommendation to the test team. In practice, this may not be possible because of inadequate test tools, pressures of schedules, limited resources, etc. Most tests are accomplished using a certain degree of automation and test procedures that are labor intensive. This paper discusses some simulation techniques that can improve the automation of the test process. The TASS system tests the POCC/MOC software and provides a score based on the test results. The TASS system displays statistics on the success of the POCC/MOC system processing in each of the three areas as well as event messages pertaining to the Test/Score/Report processing. The TASS system also provides formatted reports documenting each step performed during the tests and the results of each step. A prototype of the Test/Score/Report capability is available and currently being used to test some POCC/MOC software deliveries. When this capability is fully operational it should greatly reduce the time necessary to test a POCC/MOC software delivery, as well as improve the quality of the test process.

Aeropropulsion facilities configuration control: Procedures manual

NASA Technical Reports Server (NTRS)

Lavelle, James J.

1990-01-01

Lewis Research Center senior management directed that the aeropropulsion facilities be put under configuration control. A Configuration Management (CM) program was established by the Facilities Management Branch of the Aeropropulsion Facilities and Experiments Division. Under the CM program, a support service contractor was engaged to staff and implement the program. The Aeronautics Directorate has over 30 facilities at Lewis of various sizes and complexities. Under the program, a Facility Baseline List (FBL) was established for each facility, listing which systems and their documents were to be placed under configuration control. A Change Control System (CCS) was established requiring that any proposed changes to FBL systems or their documents were to be processed as per the CCS. Limited access control of the FBL master drawings was implemented and an audit system established to ensure all facility changes are properly processed. This procedures manual sets forth the policy and responsibilities to ensure all key documents constituting a facilities configuration are kept current, modified as needed, and verified to reflect any proposed change. This is the essence of the CM program.

Decontamination and Management of Human Remains Following Incidents of Hazardous Chemical Release

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hauschild, Veronique; Watson, Annetta Paule; Bock, Robert Eldon

2012-01-01

Abstract Objective: To provide specific procedural guidance and resources for identification, assessment, control, and mitigation of compounds that may contaminate human remains resulting from chemical attack or release. Design: A detailed technical, policy, and regulatory review is summarized. Setting: Guidance is suitable for civilian or military settings where human remains potentially contaminated with hazardous chemicals may be present. Settings would include sites of transportation accidents, natural disasters, terrorist or military operations, mortuary affairs or medical examiner processing and decontamination points, and similar. Patients, Participants: While recommended procedures have not been validated with actual human remains, guidance has been developed frommore » data characterizing controlled experiments with fabrics, materiel, and laboratory animals. Main Outcome Measure(s): Presentation of logic and specific procedures for remains management, protection and decontamination of mortuary affairs personnel, as well as decision criteria for determining when remains are sufficiently decontaminated so as to pose no chemical health hazard. Results: Established procedures and existing equipment/materiel available for decontamination and verification provide appropriate and reasonable means to mitigate chemical hazards from remains. Extensive characterization of issues related to remains decontamination indicates that supra-lethal concentrations of liquid chemical warfare agent VX may prove difficult to decontaminate and verify in a timely fashion. Specialized personnel can and should be called upon to assist with monitoring necessary to clear decontaminated remains for transport and processing. Conclusions: Once appropriate decontamination and verification have been accomplished, normal procedures for remains processing and transport to the decedent s family and the continental United States can be followed.« less

Implementation of a partitioned algorithm for simulation of large CSI problems

NASA Technical Reports Server (NTRS)

Alvin, Kenneth F.; Park, K. C.

1991-01-01

The implementation of a partitioned numerical algorithm for determining the dynamic response of coupled structure/controller/estimator finite-dimensional systems is reviewed. The partitioned approach leads to a set of coupled first and second-order linear differential equations which are numerically integrated with extrapolation and implicit step methods. The present software implementation, ACSIS, utilizes parallel processing techniques at various levels to optimize performance on a shared-memory concurrent/vector processing system. A general procedure for the design of controller and filter gains is also implemented, which utilizes the vibration characteristics of the structure to be solved. Also presented are: example problems; a user's guide to the software; the procedures and algorithm scripts; a stability analysis for the algorithm; and the source code for the parallel implementation.

Assessment of average of normals (AON) procedure for outlier-free datasets including qualitative values below limit of detection (LoD): an application within tumor markers such as CA 15-3, CA 125, and CA 19-9.

PubMed

Usta, Murat; Aral, Hale; Mete Çilingirtürk, Ahmet; Kural, Alev; Topaç, Ibrahim; Semerci, Tuna; Hicri Köseoğlu, Mehmet

2016-11-01

Average of normals (AON) is a quality control procedure that is sensitive only to systematic errors that can occur in an analytical process in which patient test results are used. The aim of this study was to develop an alternative model in order to apply the AON quality control procedure to datasets that include qualitative values below limit of detection (LoD). The reported patient test results for tumor markers, such as CA 15-3, CA 125, and CA 19-9, analyzed by two instruments, were retrieved from the information system over a period of 5 months, using the calibrator and control materials with the same lot numbers. The median as a measure of central tendency and the median absolute deviation (MAD) as a measure of dispersion were used for the complementary model of AON quality control procedure. The u bias values, which were determined for the bias component of the measurement uncertainty, were partially linked to the percentages of the daily median values of the test results that fall within the control limits. The results for these tumor markers, in which lower limits of reference intervals are not medically important for clinical diagnosis and management, showed that the AON quality control procedure, using the MAD around the median, can be applied for datasets including qualitative values below LoD.

Aeroservoelasticity

NASA Technical Reports Server (NTRS)

Noll, Thomas E.

1990-01-01

The paper describes recent accomplishments and current research projects along four main thrusts in aeroservoelasticity at NASA Langley. One activity focuses on enhancing the modeling and analysis procedures to accurately predict aeroservoelastic interactions. Improvements to the minimum-state method of approximating unsteady aerodynamics are shown to provide precise low-order models for design and simulation tasks. Recent extensions in aerodynamic correction-factor methodology are also described. With respect to analysis procedures, the paper reviews novel enhancements to matched filter theory and random process theory for predicting the critical gust profile and the associated time-correlated gust loads for structural design considerations. Two research projects leading towards improved design capability are also summarized: (1) an integrated structure/control design capability and (2) procedures for obtaining low-order robust digital control laws for aeroelastic applications.

Modified Exponential Weighted Moving Average (EWMA) Control Chart on Autocorrelation Data

NASA Astrophysics Data System (ADS)

Herdiani, Erna Tri; Fandrilla, Geysa; Sunusi, Nurtiti

2018-03-01

In general, observations of the statistical process control are assumed to be mutually independence. However, this assumption is often violated in practice. Consequently, statistical process controls were developed for interrelated processes, including Shewhart, Cumulative Sum (CUSUM), and exponentially weighted moving average (EWMA) control charts in the data that were autocorrelation. One researcher stated that this chart is not suitable if the same control limits are used in the case of independent variables. For this reason, it is necessary to apply the time series model in building the control chart. A classical control chart for independent variables is usually applied to residual processes. This procedure is permitted provided that residuals are independent. In 1978, Shewhart modification for the autoregressive process was introduced by using the distance between the sample mean and the target value compared to the standard deviation of the autocorrelation process. In this paper we will examine the mean of EWMA for autocorrelation process derived from Montgomery and Patel. Performance to be investigated was investigated by examining Average Run Length (ARL) based on the Markov Chain Method.

Application of a repetitive process setting to design of monotonically convergent iterative learning control

NASA Astrophysics Data System (ADS)

Boski, Marcin; Paszke, Wojciech

2015-11-01

This paper deals with the problem of designing an iterative learning control algorithm for discrete linear systems using repetitive process stability theory. The resulting design produces a stabilizing output feedback controller in the time domain and a feedforward controller that guarantees monotonic convergence in the trial-to-trial domain. The results are also extended to limited frequency range design specification. New design procedure is introduced in terms of linear matrix inequality (LMI) representations, which guarantee the prescribed performances of ILC scheme. A simulation example is given to illustrate the theoretical developments.

Analytical procedure validation and the quality by design paradigm.

PubMed

Rozet, Eric; Lebrun, Pierre; Michiels, Jean-François; Sondag, Perceval; Scherder, Tara; Boulanger, Bruno

2015-01-01

Since the adoption of the ICH Q8 document concerning the development of pharmaceutical processes following a quality by design (QbD) approach, there have been many discussions on the opportunity for analytical procedure developments to follow a similar approach. While development and optimization of analytical procedure following QbD principles have been largely discussed and described, the place of analytical procedure validation in this framework has not been clarified. This article aims at showing that analytical procedure validation is fully integrated into the QbD paradigm and is an essential step in developing analytical procedures that are effectively fit for purpose. Adequate statistical methodologies have also their role to play: such as design of experiments, statistical modeling, and probabilistic statements. The outcome of analytical procedure validation is also an analytical procedure design space, and from it, control strategy can be set.

Badging people not on your payroll.

PubMed

Hogan, Mary Alice

2009-01-01

A complex badging process to create a culture of safety in a medical center is described by the author. Badging is not only used to control access by employees, but non-employees--medical students, vendors, contractors, volunteers, etc.--are subjected to similar processing procedures before they can be issued badges.

32 CFR 93.5 - Procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... will communicate with the NSA person and serve as the contact point for the person and the process..., will be referred to the Visitor Control Center (VCC) at Operations Building 2A. The VCC will contact... process will not be accepted during non-duty hours unless prior arrangements have been made by the OGC...

32 CFR 93.5 - Procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... will communicate with the NSA person and serve as the contact point for the person and the process..., will be referred to the Visitor Control Center (VCC) at Operations Building 2A. The VCC will contact... process will not be accepted during non-duty hours unless prior arrangements have been made by the OGC...

32 CFR 93.5 - Procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... will communicate with the NSA person and serve as the contact point for the person and the process..., will be referred to the Visitor Control Center (VCC) at Operations Building 2A. The VCC will contact... process will not be accepted during non-duty hours unless prior arrangements have been made by the OGC...

32 CFR 93.5 - Procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... will communicate with the NSA person and serve as the contact point for the person and the process..., will be referred to the Visitor Control Center (VCC) at Operations Building 2A. The VCC will contact... process will not be accepted during non-duty hours unless prior arrangements have been made by the OGC...

32 CFR 93.5 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... will communicate with the NSA person and serve as the contact point for the person and the process..., will be referred to the Visitor Control Center (VCC) at Operations Building 2A. The VCC will contact... process will not be accepted during non-duty hours unless prior arrangements have been made by the OGC...

40 CFR 63.653 - Monitoring, recordkeeping, and implementation plan for emissions averaging.

Code of Federal Regulations, 2013 CFR

2013-07-01

... § 63.120 of subpart G; and (ii) For closed vent systems with control devices, conduct an initial design..., monitoring, recordkeeping, and reporting equivalent to that required for Group 1 emission points complying... control device. (2) The source shall implement the following procedures for each miscellaneous process...

Effect of episodic and working memory impairments on semantic and cognitive procedural learning at alcohol treatment entry.

PubMed

Pitel, Anne Lise; Witkowski, Thomas; Vabret, François; Guillery-Girard, Bérengère; Desgranges, Béatrice; Eustache, Francis; Beaunieux, Hélène

2007-02-01

Chronic alcoholism is known to impair the functioning of episodic and working memory, which may consequently reduce the ability to learn complex novel information. Nevertheless, semantic and cognitive procedural learning have not been properly explored at alcohol treatment entry, despite its potential clinical relevance. The goal of the present study was therefore to determine whether alcoholic patients, immediately after the weaning phase, are cognitively able to acquire complex new knowledge, given their episodic and working memory deficits. Twenty alcoholic inpatients with episodic memory and working memory deficits at alcohol treatment entry and a control group of 20 healthy subjects underwent a protocol of semantic acquisition and cognitive procedural learning. The semantic learning task consisted of the acquisition of 10 novel concepts, while subjects were administered the Tower of Toronto task to measure cognitive procedural learning. Analyses showed that although alcoholic subjects were able to acquire the category and features of the semantic concepts, albeit slowly, they presented impaired label learning. In the control group, executive functions and episodic memory predicted semantic learning in the first and second halves of the protocol, respectively. In addition to the cognitive processes involved in the learning strategies invoked by controls, alcoholic subjects seem to attempt to compensate for their impaired cognitive functions, invoking capacities of short-term passive storage. Regarding cognitive procedural learning, although the patients eventually achieved the same results as the controls, they failed to automate the procedure. Contrary to the control group, the alcoholic groups' learning performance was predicted by controlled cognitive functions throughout the protocol. At alcohol treatment entry, alcoholic patients with neuropsychological deficits have difficulty acquiring novel semantic and cognitive procedural knowledge. Compared with controls, they seem to use more costly learning strategies, which are nonetheless less efficient. These learning disabilities need to be considered when treatment requiring the acquisition of complex novel information is envisaged.

Audit of the internal controls over the processing of oil overcharge refunds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-03-31

This report is on internal controls over the processing of oil overcharge refunds. The Office of Hearings and Appeals administers the distribution of refunds to parties that were overcharged during the period of petroleum price controls. The refund process was initiated in 1979. As of September 30, 1991, Hearings and Appeals had received over 200,000 applications for refunds. It had granted refunds with a total value of more than 600 million on about 160,000 applications, with 26,636 applications pending. The objectie of the audit was to evaluate the adequacy of Hearings and Appeals' internal controls over refund practices and procedures,more » specifically those used to ensure that claims approved were complete, systematically processed, and properly distributed.« less

Audit of the internal controls over the processing of oil overcharge refunds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-03-31

This report is on internal controls over the processing of oil overcharge refunds. The Office of Hearings and Appeals administers the distribution of refunds to parties that were overcharged during the period of petroleum price controls. The refund process was initiated in 1979. As of September 30, 1991, Hearings and Appeals had received over 200,000 applications for refunds. It had granted refunds with a total value of more than 600 million on about 160,000 applications, with 26,636 applications pending. The objectie of the audit was to evaluate the adequacy of Hearings and Appeals` internal controls over refund practices and procedures,more » specifically those used to ensure that claims approved were complete, systematically processed, and properly distributed.« less

Modeling of dialogue regimes of distance robot control

NASA Astrophysics Data System (ADS)

Larkin, E. V.; Privalov, A. N.

2017-02-01

Process of distance control of mobile robots is investigated. Petri-Markov net for modeling of dialogue regime is worked out. It is shown, that sequence of operations of next subjects: a human operator, a dialogue computer and an onboard computer may be simulated with use the theory of semi-Markov processes. From the semi-Markov process of the general form Markov process was obtained, which includes only states of transaction generation. It is shown, that a real transaction flow is the result of «concurrency» in states of Markov process. Iteration procedure for evaluation of transaction flow parameters, which takes into account effect of «concurrency», is proposed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

A. Alfonsi; C. Rabiti; D. Mandelli

The Reactor Analysis and Virtual control ENviroment (RAVEN) code is a software tool that acts as the control logic driver and post-processing engine for the newly developed Thermal-Hydraulic code RELAP-7. RAVEN is now a multi-purpose Probabilistic Risk Assessment (PRA) software framework that allows dispatching different functionalities: Derive and actuate the control logic required to simulate the plant control system and operator actions (guided procedures), allowing on-line monitoring/controlling in the Phase Space Perform both Monte-Carlo sampling of random distributed events and Dynamic Event Tree based analysis Facilitate the input/output handling through a Graphical User Interface (GUI) and a post-processing data miningmore » module« less

Procedures in complex systems: the airline cockpit.

PubMed

Degani, A; Wiener, E L

1997-05-01

In complex human-machine systems, successful operations depend on an elaborate set of procedures which are specified by the operational management of the organization. These procedures indicate to the human operator (in this case the pilot) the manner in which operational management intends to have various tasks done. The intent is to provide guidance to the pilots and to ensure a safe, logical, efficient, and predictable (standardized) means of carrying out the objectives of the job. However, procedures can become a hodge-podge. Inconsistent or illogical procedures may lead to noncompliance by operators. Based on a field study with three major airlines, the authors propose a model for procedure development called the "Four P's": philosophy, policies, procedures, and practices. Using this model as a framework, the authors discuss the intricate issue of designing flight-deck procedures, and propose a conceptual approach for designing any set of procedures. The various factors, both external and internal to the cockpit, that must be considered for procedure design are presented. In particular, the paper addresses the development of procedures for automated cockpits--a decade-long, and highly controversial issue in commercial aviation. Although this paper is based on airline operations, we assume that the principles discussed here are also applicable to other high-risk supervisory control systems, such as space flight, manufacturing process control, nuclear power production, and military operations.

Cerebellar contribution to spatial event processing: involvement in procedural and working memory components.

PubMed

Mandolesi, L; Leggio, M G; Graziano, A; Neri, P; Petrosini, L

2001-12-01

Spatial function is one of the cognitive functions altered in the presence of cerebellar lesions. We investigated the cerebellar contribution to the acquisition of spatial procedural and working memory components by means of a radial maze. To establish whether a cerebellar lesion would cause a deficit in solving the radial maze, a first experiment was carried out by using a full-baited maze procedure in different experimental groups, with or without cerebellar lesion and with or without pretraining. Non-pretrained hemicerebellectomized (HCbed) animals exhibited impaired performances in all (motor, spatial and procedural) task aspects. Pre-trained HCbed animals performed similarly to control animals in the task aspects linked to the processing of spatial and procedural factors. To distinguish procedural from working memory components, a forced-choice paradigm of the radial maze was used in the second experiment. Non-pretrained HCbed rats continued to make a lot of errors and show severe perseverative tendencies, already observed in the first experiment, supporting a specific cerebellar role in acquiring new behaviours and in modifying them in relation to the context. Interestingly, hindered from putting the acquired explorative patterns into action and compelled to use only working memory abilities, the pretrained HCbed group exhibited a dramatic worsening of performance. In conclusion, the present findings demonstrate that cerebellar damage induces a specific behaviour in radial maze tasks, characterized by an inflexible use of the procedures (if indeed any procedure was acquired before the lesion) and by a severe impairment in working memory processes.

Automatic tracking of laparoscopic instruments for autonomous control of a cameraman robot.

PubMed

Khoiy, Keyvan Amini; Mirbagheri, Alireza; Farahmand, Farzam

2016-01-01

An automated instrument tracking procedure was designed and developed for autonomous control of a cameraman robot during laparoscopic surgery. The procedure was based on an innovative marker-free segmentation algorithm for detecting the tip of the surgical instruments in laparoscopic images. A compound measure of Saturation and Value components of HSV color space was incorporated that was enhanced further using the Hue component and some essential characteristics of the instrument segment, e.g., crossing the image boundaries. The procedure was then integrated into the controlling system of the RoboLens cameraman robot, within a triple-thread parallel processing scheme, such that the tip is always kept at the center of the image. Assessment of the performance of the system on prerecorded real surgery movies revealed an accuracy rate of 97% for high quality images and about 80% for those suffering from poor lighting and/or blood, water and smoke noises. A reasonably satisfying performance was also observed when employing the system for autonomous control of the robot in a laparoscopic surgery phantom, with a mean time delay of 200ms. It was concluded that with further developments, the proposed procedure can provide a practical solution for autonomous control of cameraman robots during laparoscopic surgery operations.

Identifyability measures to select the parameters to be estimated in a solid-state fermentation distributed parameter model.

PubMed

da Silveira, Christian L; Mazutti, Marcio A; Salau, Nina P G

2016-07-08

Process modeling can lead to of advantages such as helping in process control, reducing process costs and product quality improvement. This work proposes a solid-state fermentation distributed parameter model composed by seven differential equations with seventeen parameters to represent the process. Also, parameters estimation with a parameters identifyability analysis (PIA) is performed to build an accurate model with optimum parameters. Statistical tests were made to verify the model accuracy with the estimated parameters considering different assumptions. The results have shown that the model assuming substrate inhibition better represents the process. It was also shown that eight from the seventeen original model parameters were nonidentifiable and better results were obtained with the removal of these parameters from the estimation procedure. Therefore, PIA can be useful to estimation procedure, since it may reduce the number of parameters that can be evaluated. Further, PIA improved the model results, showing to be an important procedure to be taken. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:905-917, 2016. © 2016 American Institute of Chemical Engineers.

A novel approach to scavenging anesthetic gases in rodent surgery.

PubMed

Nesbitt, Jeffrey C; Krageschmidt, Dale A; Blanco, Michael C

2013-01-01

Laboratory animal procedures using gas anesthetics may amass elevated waste gas concentrations in operating rooms if controls are not implemented for capturing and removing the vapors. Area sampling using an infrared analyzer indicated isoflurane concentrations likely to exceed occupational exposure guidelines. Our study showed environmental concentrations of oxygen as high as 40% and isoflurane concentrations >100 ppm when no controls or merely passive controls were utilized. These extraneous isoflurane emissions were determined to be originating from the pre-procedural induction process as well as the gas delivery nose cone. A novel waste gas collection cylinder was designed to enclose the gas delivery nose cone and animal head during the administration of anesthetic gases. The vented cylinder utilized a house vacuum to remove the waste anesthetic gases from the surgical field. A commercially available induction chamber designed to be actively and externally exhausted was used to lower concentrations during the induction process. With implementation of local exhaust ventilation controls, waste anesthetic gas concentrations decreased to below recommended occupational exposure levels. In vitro (sham) testing compared favorably to in vivo measurements validating the reduction capability of active ventilation during rodent anesthetic administration. In vivo isoflurane reductions for the induction chamber emissions, the operating room, and the surgeon's breathing zone were 95%, 60%, and 53%, respectively. The same measurements for an in vitro procedure were 98%, 84%, and 87%, respectively.

Information Quality in Regulatory Decision Making: Peer Review versus Good Laboratory Practice.

PubMed

McCarty, Lynn S; Borgert, Christopher J; Mihaich, Ellen M

2012-07-01

There is an ongoing discussion on the provenance of toxicity testing data regarding how best to ensure its validity and credibility. A central argument is whether journal peer-review procedures are superior to Good Laboratory Practice (GLP) standards employed for compliance with regulatory mandates. We sought to evaluate the rationale for regulatory decision making based on peer-review procedures versus GLP standards. We examined pertinent published literature regarding how scientific data quality and validity are evaluated for peer review, GLP compliance, and development of regulations. Some contend that peer review is a coherent, consistent evaluative procedure providing quality control for experimental data generation, analysis, and reporting sufficient to reliably establish relative merit, whereas GLP is seen as merely a tracking process designed to thwart investigator corruption. This view is not supported by published analyses pointing to subjectivity and variability in peer-review processes. Although GLP is not designed to establish relative merit, it is an internationally accepted quality assurance, quality control method for documenting experimental conduct and data. Neither process is completely sufficient for establishing relative scientific soundness. However, changes occurring both in peer-review processes and in regulatory guidance resulting in clearer, more transparent communication of scientific information point to an emerging convergence in ensuring information quality. The solution to determining relative merit lies in developing a well-documented, generally accepted weight-of-evidence scheme to evaluate both peer-reviewed and GLP information used in regulatory decision making where both merit and specific relevance inform the process.

Performance of ground attitude determination procedures for HEAO-1

NASA Technical Reports Server (NTRS)

Fallon, L., III; Sturch, C. R.

1978-01-01

Ground attitude support for HEAO 1 provided at GSFC by the HEAO 1 Attitude Ground Support System (AGSS) is described. Information telemetered from Sun sensors, gyroscopes, star trackers, and an onboard computer are used by the AGSS to compute updates to the onboard attitude reference and gyro calibration parameters. The onboard computer utilizes these updates in providing continuous attitudes (accurate to 0.25degree) for use in the observatory's attitude control procedures. The relationship between HEAO 1 onboard and ground processing, the procedures used by the AGSS in computing attitude and gyro calibration updates, and the performance of these procedures in the HEAO 1 postlaunch environment is discussed.

Writing standard operating procedures (SOPs) for cryostorage protocols: using shoot meristem cryopreservation as an example.

PubMed

Harding, Keith; Benson, Erica E

2015-01-01

Standard operating procedures are a systematic way of making sure that biopreservation processes, tasks, protocols, and operations are correctly and consistently performed. They are the basic documents of biorepository quality management systems and are used in quality assurance, control, and improvement. Methodologies for constructing workflows and writing standard operating procedures and work instructions are described using a plant cryopreservation protocol as an example. This chapter is pertinent to other biopreservation sectors because how methods are written, interpreted, and implemented can affect the quality of storage outcomes.

Suboptimal distributed control and estimation: application to a four coupled tanks system

NASA Astrophysics Data System (ADS)

Orihuela, Luis; Millán, Pablo; Vivas, Carlos; Rubio, Francisco R.

2016-06-01

The paper proposes an innovative estimation and control scheme that enables the distributed monitoring and control of large-scale processes. The proposed approach considers a discrete linear time-invariant process controlled by a network of agents that may both collect information about the evolution of the plant and apply control actions to drive its behaviour. The problem makes full sense when local observability/controllability is not assumed and the communication between agents can be exploited to reach system-wide goals. Additionally, to reduce agents bandwidth requirements and power consumption, an event-based communication policy is studied. The design procedure guarantees system stability, allowing the designer to trade-off performance, control effort and communication requirements. The obtained controllers and observers are implemented in a fully distributed fashion. To illustrate the performance of the proposed technique, experimental results on a quadruple-tank process are provided.

Software control and system configuration management - A process that works

NASA Technical Reports Server (NTRS)

Petersen, K. L.; Flores, C., Jr.

1983-01-01

A comprehensive software control and system configuration management process for flight-crucial digital control systems of advanced aircraft has been developed and refined to insure efficient flight system development and safe flight operations. Because of the highly complex interactions among the hardware, software, and system elements of state-of-the-art digital flight control system designs, a systems-wide approach to configuration control and management has been used. Specific procedures are implemented to govern discrepancy reporting and reconciliation, software and hardware change control, systems verification and validation testing, and formal documentation requirements. An active and knowledgeable configuration control board reviews and approves all flight system configuration modifications and revalidation tests. This flexible process has proved effective during the development and flight testing of several research aircraft and remotely piloted research vehicles with digital flight control systems that ranged from relatively simple to highly complex, integrated mechanizations.

Piloted simulation of an air-ground profile negotiation process in a time-based Air Traffic Control environment

NASA Technical Reports Server (NTRS)

Williams, David H.; Green, Steven M.

1993-01-01

Historically, development of airborne flight management systems (FMS) and ground-based air traffic control (ATC) systems has tended to focus on different objectives with little consideration for operational integration. A joint program, between NASA's Ames Research Center (Ames) and Langley Research Center (Langley), is underway to investigate the issues of, and develop systems for, the integration of ATC and airborne automation systems. A simulation study was conducted to evaluate a profile negotiation process (PNP) between the Center/TRACON Automation System (CTAS) and an aircraft equipped with a four-dimensional flight management system (4D FMS). Prototype procedures were developed to support the functional implementation of this process. The PNP was designed to provide an arrival trajectory solution which satisfies the separation requirements of ATC while remaining as close as possible to the aircraft's preferred trajectory. Results from the experiment indicate the potential for successful incorporation of aircraft-preferred arrival trajectories in the CTAS automation environment. Fuel savings on the order of 2 percent to 8 percent, compared to fuel required for the baseline CTAS arrival speed strategy, were achieved in the test scenarios. The data link procedures and clearances developed for this experiment, while providing the necessary functionality, were found to be operationally unacceptable to the pilots. In particular, additional pilot control and understanding of the proposed aircraft-preferred trajectory, and a simplified clearance procedure were cited as necessary for operational implementation of the concept.

Reactance in affective-evaluative learning: Outside of conscious control?

PubMed

Fulcher, Eamon P; Hammerl, Marianne

2005-02-01

Recent studies have shown that the basic evaluative conditioning (EC) effect (originally neutral stimuli acquiring an affective value congruent with the valence of the affective stimulus they were paired with) seems to be limited to participants who are unaware of the stimulus pairings. If participants are aware of the pairings, reactance effects occur (i.e., changes in the opposite direction of the valence of the affective stimulus). To examine whether these reactance effects are due to processes of conscious countercontrol or whether the ratings reflect intrinsic feelings towards the stimuli, a new procedure was developed that included a bogus-pipeline condition. In this procedure, which was adapted from attitude research, participants were connected to bogus lie detector equipment leading them to believe that their "true" affective-evaluative responses were being observed. In Experiment 1, reactance effects occurred also in this procedure, suggesting that the effect is spontaneous and not due to processes of conscious countercontrol. In Experiment 2, these effects were replicated using a between-subjects design in addition to the standard within-subjects control condition.

Providing support to family members.

PubMed

Davidhizar, Ruth; Dowd, Steven

2004-01-01

Providing recognition and simple information can be powerful and reassure a family member who is anxious and worried about an ill relative. While "answers" concerning the procedure are often not available, providing information that is available--the locations of the rest rooms and coffee shop; approximately how long the procedure will take; where to wait; and the process involved in the radiological procedure, reading and getting the results--can give some feeling of control, and thus reduce feelings of powerlessness. Most importantly, family members who are recognized and included with the patient in the treatment process will be reassured of the competency of the staff and gain hopefulness about the outcome of the diagnostic and treatment experience. And providing hope in the healthcare setting is a radiology professional's most important job.

Nuclear Technology. Course 28: Welding Inspection. Module 28-6, Process Controls.

ERIC Educational Resources Information Center

Espy, John

This sixth in a series of ten modules for a course titled Welding Inspection describes procedures review, process monitoring, and weld defect analysis. The module follows a typical format that includes the following sections: (1) introduction, (2) module prerequisites, (3) objectives, (4) notes to instructor/student, (5) subject matter, (6)…

Recording and cataloging hazards information, revision A

NASA Technical Reports Server (NTRS)

Stein, R. J.

1974-01-01

A data collection process is described for the purpose of discerning causation factors of accidents, and the establishment of boundaries or controls aimed at mitigating and eliminating accidents. A procedure is proposed that suggests a discipline approach to hazard identification based on energy interrelationships together with an integrated control technique which takes the form of checklists.

Processes, Procedures, and Methods to Control Pollution Resulting from Silvicultural Activities.

ERIC Educational Resources Information Center

Environmental Protection Agency, Washington, DC. Office of Water Programs.

This report presents brief documentation of silvicultural practices, both those now in use and those in stages of research and development. A majority of the text is concerned with the specific aspects of silvicultural activities which relate to nonpoint source pollution control methods. Analyzed are existing and near future pollution control…

Corrosion Prevention for Wheeled Vehicle Systems

DTIC Science & Technology

1993-08-13

The audit objective was to evaluate the effectiveness and efficiency of the Army’s procedures for acquiring corrosion prevention and chemical agent...resistant coatings for wheeled vehicle systems. To accomplish this objective, we reviewed corrosion controls and painting processes. The audit also...included a review of the adequacy of internal controls related to the audit objective.

9 CFR 381.305 - Equipment and procedures for heat processing systems.

Code of Federal Regulations, 2010 CFR

2010-01-01

... control unit. A nonreturn valve shall be provided in the air supply line to prevent water from entering... control unit. A nonreturn valve shall be provided in the air supply line to prevent water from entering... supply of clean, dry air. The recorder timing mechanism shall be accurate. (i) Chart-type devices...

46 CFR 162.050-5 - Contents of application.

Code of Federal Regulations, 2014 CFR

2014-10-01

... control procedures, in-process and final inspections and tests followed in manufacturing the item, and..., and maintenance of the item. (7) For each monitor and bilge alarm and each control on a separator, the vibration test report described in § 162.050-37. (8) For each oil content meter, a statement of whether it...

46 CFR 162.050-5 - Contents of application.

Code of Federal Regulations, 2011 CFR

2011-10-01

... control procedures, in-process and final inspections and tests followed in manufacturing the item, and..., and maintenance of the item. (7) For each monitor and bilge alarm and each control on a separator, the vibration test report described in § 162.050-37. (8) For each oil content meter, a statement of whether it...

46 CFR 162.050-5 - Contents of application.

Code of Federal Regulations, 2013 CFR

2013-10-01

... control procedures, in-process and final inspections and tests followed in manufacturing the item, and..., and maintenance of the item. (7) For each monitor and bilge alarm and each control on a separator, the vibration test report described in § 162.050-37. (8) For each oil content meter, a statement of whether it...

Infection control practices for dental radiography.

PubMed

Palenik, Charles John

2004-06-01

Infection control for dental radiography employs the same materials, processes, and techniques used in the operatory, yet unless proper procedures are established and followed, there is a definite potential for cross-contamination to clinical area surfaces and DHCP. In general, the aseptic practices used are relatively simple and inexpensive, yet they require complete application in every situation.

Software Certification - Coding, Code, and Coders

NASA Technical Reports Server (NTRS)

Havelund, Klaus; Holzmann, Gerard J.

2011-01-01

We describe a certification approach for software development that has been adopted at our organization. JPL develops robotic spacecraft for the exploration of the solar system. The flight software that controls these spacecraft is considered to be mission critical. We argue that the goal of a software certification process cannot be the development of "perfect" software, i.e., software that can be formally proven to be correct under all imaginable and unimaginable circumstances. More realistically, the goal is to guarantee a software development process that is conducted by knowledgeable engineers, who follow generally accepted procedures to control known risks, while meeting agreed upon standards of workmanship. We target three specific issues that must be addressed in such a certification procedure: the coding process, the code that is developed, and the skills of the coders. The coding process is driven by standards (e.g., a coding standard) and tools. The code is mechanically checked against the standard with the help of state-of-the-art static source code analyzers. The coders, finally, are certified in on-site training courses that include formal exams.

Cryogenic fluid management in space

NASA Technical Reports Server (NTRS)

Antar, Basil N.

1988-01-01

Many future space based vehicles and satellites will require on orbit refuelling procedures. Cryogenic fluid management technology is being developed to assess the requirements of such procedures as well as to aid in the design and development of these vehicles. Cryogenic fluid management technology for this application could be divided into two areas of study, one is concerned with fluid transfer process and the other with cryogenic liquid storage. This division is based upon the needed technology for the development of each area. In the first, the interaction of fluid dynamics with thermodynamics is essential, while in the second only thermodynamic analyses are sufficient to define the problem. The following specific process related to the liquid transfer area are discussed: tank chilldown and fill; tank pressurization; liquid positioning; and slosh dynamics and control. These specific issues are discussed in relation with the required technology for their development in the low gravity application area. In each process the relevant physics controlling the technology is identified and methods for resolving some of the basic questions are discussed.

Guidelines for the processing and quality assurance of benthic invertebrate samples collected as part of the National Water-Quality Assessment Program

USGS Publications Warehouse

Cuffney, T.F.; Gurtz, M.E.; Meador, M.R.

1993-01-01

Benthic invertebrate samples are collected as part of the U.S. Geological Survey's National Water-Quality Assessment Program. This is a perennial, multidisciplinary program that integrates biological, physical, and chemical indicators of water quality to evaluate status and trends and to develop an understanding of the factors controlling observed water quality. The Program examines water quality in 60 study units (coupled ground- and surface-water systems) that encompass most of the conterminous United States and parts of Alaska and Hawaii. Study-unit teams collect and process qualitative and semi-quantitative invertebrate samples according to standardized procedures. These samples are processed (elutriated and subsampled) in the field to produce as many as four sample components: large-rare, main-body, elutriate, and split. Each sample component is preserved in 10-percent formalin, and two components, large-rare and main-body, are sent to contract laboratories for further processing. The large-rare component is composed of large invertebrates that are removed from the sample matrix during field processing and placed in one or more containers. The main-body sample component consists of the remaining sample materials (sediment, detritus, and invertebrates) and is subsampled in the field to achieve a volume of 750 milliliters or less. The remaining two sample components, elutriate and split, are used for quality-assurance and quality-control purposes. Contract laboratories are used to identify and quantify invertebrates from the large-rare and main-body sample components according to the procedures and guidelines specified within this document. These guidelines allow the use of subsampling techniques to reduce the volume of sample material processed and to facilitate identifications. These processing procedures and techniques may be modified if the modifications provide equal or greater levels of accuracy and precision. The intent of sample processing is to determine the quantity of each taxon present in the semi-quantitative samples or to list the taxa present in qualitative samples. The processing guidelines provide standardized laboratory forms, sample labels, detailed sample processing flow charts, standardized format for electronic data, quality-assurance procedures and checks, sample tracking standards, and target levels for taxonomic determinations. The contract laboratory (1) is responsible for identifications and quantifications, (2) constructs reference collections, (3) provides data in hard copy and electronic forms, (4) follows specified quality-assurance and quality-control procedures, and (5) returns all processed and unprocessed portions of the samples. The U.S. Geological Survey's Quality Management Group maintains a Biological Quality-Assurance Unit, located at the National Water-Quality Laboratory, Arvada, Colorado, to oversee the use of contract laboratories and ensure the quality of data obtained from these laboratories according to the guidelines established in this document. This unit establishes contract specifications, reviews contractor performance (timeliness, accuracy, and consistency), enters data into the National Water Information System-II data base, maintains in-house reference collections, deposits voucher specimens in outside museums, and interacts with taxonomic experts within and outside the U.S. Geological Survey. This unit also modifies the existing sample processing and quality-assurance guidelines, establishes criteria and testing procedures for qualifying potential contract laboratories, identifies qualified taxonomic experts, and establishes voucher collections.

Adhesive bonded structural repair. II - Surface preparation procedures, tools, equipment and facilities

NASA Astrophysics Data System (ADS)

Wegman, Raymond F.; Tullos, Thomas R.

1993-10-01

A development status report is presented on the surface preparation procedures, tools, equipment, and facilities used in adhesively-bonded repair of aerospace and similar high-performance structures. These methods extend to both metallic and polymeric surfaces. Attention is given to the phos-anodize containment system, paint removal processes, tools for cutting composite prepreg and fabric materials, autoclaves, curing ovens, vacuum bagging, and controlled atmospheres.

[Use of nondeclarative and automatic memory processes in motor learning: how to mitigate the effects of aging].

PubMed

Chauvel, Guillaume; Maquestiaux, François; Didierjean, André; Joubert, Sven; Dieudonné, Bénédicte; Verny, Marc

2011-12-01

Does normal aging inexorably lead to diminished motor learning abilities? This article provides an overview of the literature on the question, with particular emphasis on the functional dissociation between two sets of memory processes: declarative, effortful processes, and non-declarative, automatic processes. There is abundant evidence suggesting that aging does impair learning when past memories of former actions are required (episodic memory) and recollected through controlled processing (working memory). However, other studies have shown that aging does not impair learning when motor actions are performed non verbally and automatically (tapping procedural memory). These findings led us to hypothesize that one can minimize the impact of aging on the ability to learn new motor actions by favouring procedural learning. Recent data validating this hypothesis are presented. Our findings underline the importance of developing new motor learning strategies, which "bypass" declarative, effortful memory processes.

Use of Structure as a Basis for Abstraction in Air Traffic Control

NASA Technical Reports Server (NTRS)

Davison, Hayley J.; Hansman, R. John

2004-01-01

The safety and efficiency of the air traffic control domain is highly dependent on the capabilities and limitations of its human controllers. Past research has indicated that structure provided by the airspace and procedures could aid in simplifying the controllers cognitive tasks. In this paper, observations, interviews, voice command data analyses, and radar analyses were conducted at the Boston Terminal Route Control (TRACON) facility to determine if there was evidence of controllers using structure to simplify their cognitive processes. The data suggest that controllers do use structure-based abstractions to simplify their cognitive processes, particularly the projection task. How structure simplifies the projection task and the implications of understanding the benefits structure provides to the projection task was discussed.

Controlling Real-Time Processes On The Space Station With Expert Systems

NASA Astrophysics Data System (ADS)

Leinweber, David; Perry, John

1987-02-01

Many aspects of space station operations involve continuous control of real-time processes. These processes include electrical power system monitoring, propulsion system health and maintenance, environmental and life support systems, space suit checkout, on-board manufacturing, and servicing of attached vehicles such as satellites, shuttles, orbital maneuvering vehicles, orbital transfer vehicles and remote teleoperators. Traditionally, monitoring of these critical real-time processes has been done by trained human experts monitoring telemetry data. However, the long duration of space station missions and the high cost of crew time in space creates a powerful economic incentive for the development of highly autonomous knowledge-based expert control procedures for these space stations. In addition to controlling the normal operations of these processes, the expert systems must also be able to quickly respond to anomalous events, determine their cause and initiate corrective actions in a safe and timely manner. This must be accomplished without excessive diversion of system resources from ongoing control activities and any events beyond the scope of the expert control and diagnosis functions must be recognized and brought to the attention of human operators. Real-time sensor based expert systems (as opposed to off-line, consulting or planning systems receiving data via the keyboard) pose particular problems associated with sensor failures, sensor degradation and data consistency, which must be explicitly handled in an efficient manner. A set of these systems must also be able to work together in a cooperative manner. This paper describes the requirements for real-time expert systems in space station control, and presents prototype implementations of space station expert control procedures in PICON (process intelligent control). PICON is a real-time expert system shell which operates in parallel with distributed data acquisition systems. It incorporates a specialized inference engine with a specialized scheduling portion specifically designed to match the allocation of system resources with the operational requirements of real-time control systems. Innovative knowledge engineering techniques used in PICON to facilitate the development of real-time sensor-based expert systems which use the special features of the inference engine are illustrated in the prototype examples.

Towards an integrated quality control procedure for eddy-covariance data

NASA Astrophysics Data System (ADS)

Vitale, Domenico; Papale, Dario

2017-04-01

The eddy-covariance technique is nowadays the most reliable and direct way, allowing to calculate the main fluxes of Sensible and Latent Heat and of Net Ecosystem Exchange, this last being the result of the difference between the CO2 assimilated by photosynthetic activities and those released to the atmosphere through the ecosystem respiration processes. Despite the improvements in accuracy of measurement instruments and software development, the eddy-covariance technique is not suitable under non-ideal conditions respect to the instruments characteristics and the physical assumption behind the technique mainly related to the well-developed and stationary turbulence conditions. Under these conditions the calculated fluxes are not reliable and need to be flagged and discarded. In order to discover these unavoidable "bad" fluxes and build dataset with the highest quality, several tests applied both on high-frequency (10-20 Hz) raw data and on half-hourly times series have been developed in the past years. Nevertheless, there is an increasing need to develop a standardized quality control procedure suitable not only for the analysis of long-term data, but also for the near-real time data processing. In this paper, we review established quality assessment procedures and present an innovative quality control strategy with the purpose of integrating the existing consolidated procedures with robust and advanced statistical tests more suitable for the analysis of time series data. The performance of the proposed quality control strategy is evaluated both on simulated and EC data distributed by the ICOS research infrastructure. It is concluded that the proposed strategy is able to flag and exclude unrealistic fluxes while being reproducible and retaining the largest possible amount of high quality data.

An atmosphere protection subsystem in the thermal power station automated process control system

NASA Astrophysics Data System (ADS)

Parchevskii, V. M.; Kislov, E. A.

2014-03-01

Matters concerned with development of methodical and mathematical support for an atmosphere protection subsystem in the thermal power station automated process control system are considered taking as an example the problem of controlling nitrogen oxide emissions at a gas-and-oil-fired thermal power station. The combined environmental-and-economic characteristics of boilers, which correlate the costs for suppressing emissions with the boiler steam load and mass discharge of nitrogen oxides in analytic form, are used as the main tool for optimal control. A procedure for constructing and applying environmental-and-economic characteristics on the basis of technical facilities available in modern instrumentation and control systems is presented.

The Launch Processing System for Space Shuttle.

NASA Technical Reports Server (NTRS)

Springer, D. A.

1973-01-01

In order to reduce costs and accelerate vehicle turnaround, a single automated system will be developed to support shuttle launch site operations, replacing a multiplicity of systems used in previous programs. The Launch Processing System will provide real-time control, data analysis, and information display for the checkout, servicing, launch, landing, and refurbishment of the launch vehicles, payloads, and all ground support systems. It will also provide real-time and historical data retrieval for management and sustaining engineering (test records and procedures, logistics, configuration control, scheduling, etc.).

Constraint processing in our extensible language for cooperative imaging system

NASA Astrophysics Data System (ADS)

Aoki, Minoru; Murao, Yo; Enomoto, Hajime

1996-02-01

The extensible WELL (Window-based elaboration language) has been developed using the concept of common platform, where both client and server can communicate with each other with support from a communication manager. This extensible language is based on an object oriented design by introducing constraint processing. Any kind of services including imaging in the extensible language is controlled by the constraints. Interactive functions between client and server are extended by introducing agent functions including a request-respond relation. Necessary service integrations are satisfied with some cooperative processes using constraints. Constraints are treated similarly to data, because the system should have flexibilities in the execution of many kinds of services. The similar control process is defined by using intentional logic. There are two kinds of constraints, temporal and modal constraints. Rendering the constraints, the predicate format as the relation between attribute values can be a warrant for entities' validity as data. As an imaging example, a processing procedure of interaction between multiple objects is shown as an image application for the extensible system. This paper describes how the procedure proceeds in the system, and that how the constraints work for generating moving pictures.

Apollo-Soyuz test project photographic film processing and sensitometric summary

NASA Technical Reports Server (NTRS)

Lockwood, H. E.

1975-01-01

The Photographic Technology Division at the NASA Lyndon B. Johnson Space Center processed original photographic films exposed in flight during the Apollo Soyuz Test Project (ASTP). Integrated with processing of the original films were strict sensitometric controls and certification procedures established prior to the flight. Information relative to the processing of the 54 rolls of original ASTP flight film and sensitometric data pertinent to each of these rolls of film is presented.

Photogrammetric aspects of remapping procedures

NASA Technical Reports Server (NTRS)

Mikhail, E. M.

1982-01-01

Photogrammetric control generation is discussed. Techniques in remote sensing data reduction are described. Emphasis is placed on methods of rectification of aerial photography and frame photography. Examples of multispectral band scanner data that were processed are presented.

A review of human-automation interaction and lessons learned

DOT National Transportation Integrated Search

2006-10-01

This report reviews 37 accidents in aviation, other vehicles, process control and other complex systems where human-automation interaction is involved. Implications about causality with respect to design, procedures, management and training are drawn...

40 CFR 725.150 - Procedural requirements for this subpart.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Microbial... section 5(b) of the Act for the submission of test data. (c) Contents of a MCAN. Each person who submits a...

40 CFR 725.150 - Procedural requirements for this subpart.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Microbial... section 5(b) of the Act for the submission of test data. (c) Contents of a MCAN. Each person who submits a...

AMO EXPRESS: A Command and Control Experiment for Crew Autonomy

NASA Technical Reports Server (NTRS)

Stetson, Howard K.; Frank, Jeremy; Cornelius, Randy; Haddock, Angie; Wang, Lui; Garner, Larry

2015-01-01

NASA is investigating a range of future human spaceflight missions, including both Mars-distance and Near Earth Object (NEO) targets. Of significant importance for these missions is the balance between crew autonomy and vehicle automation. As distance from Earth results in increasing communication delays, future crews need both the capability and authority to independently make decisions. However, small crews cannot take on all functions performed by ground today, and so vehicles must be more automated to reduce the crew workload for such missions. NASA's Advanced Exploration Systems Program funded Autonomous Mission Operations (AMO) project conducted an autonomous command and control demonstration of intelligent procedures to automatically initialize a rack onboard the International Space Station (ISS) with power and thermal interfaces, and involving core and payload command and telemetry processing, without support from ground controllers. This autonomous operations capability is enabling in scenarios such as a crew medical emergency, and representative of other spacecraft autonomy challenges. The experiment was conducted using the Expedite the Processing of Experiments for Space Station (EXPRESS) rack 7, which was located in the Port 2 location within the U.S Laboratory onboard the International Space Station (ISS). Activation and deactivation of this facility is time consuming and operationally intensive, requiring coordination of three flight control positions, 47 nominal steps, 57 commands, 276 telemetry checks, and coordination of multiple ISS systems (both core and payload). The autonomous operations concept includes a reduction of the amount of data a crew operator is required to verify during activation or de-activation, as well as integration of procedure execution status and relevant data in a single integrated display. During execution, the auto-procedures provide a step-by-step messaging paradigm and a high level status upon termination. This messaging and high level status is the only data generated for operator display. To enhance situational awareness of the operator, the Web-based Procedure Display (WebPD) provides a novel approach to the issues of procedure display and execution tracking. For this demonstration, the procedure was initiated and monitored from the ground. As the Timeliner sequences executed, their high level execution status was transmitted to ground, for WebPD consumption.

Walk-through survey report: Control technology for integrated circuit fabrication, Xerox Corporation, El Segundo, California

NASA Astrophysics Data System (ADS)

Mihlan, G. J.; Ungers, L. J.; Smith, R. K.; Mitchell, R. I.; Jones, J. H.

1983-05-01

A preliminary control technology assessment survey was conducted at the facility which manufactures N-channel metal oxide semiconductor (NMOS) integrated circuits. The facility has industrial hygiene review procedures for evaluating all new and existing process equipment. Employees are trained in safety, use of personal protective equipment, and emergency response. Workers potentially exposed to arsenic are monitored for urinary arsenic levels. The facility should be considered a candidate for detailed study based on the diversity of process operations encountered and the use of state-of-the-art technology and process equipment.

Quality-assurance plan for the analysis of fluvial sediment by the U.S. Geological Survey Kentucky Water Science Center Sediment Laboratory

USGS Publications Warehouse

Shreve, Elizabeth A.; Downs, Aimee C.

2005-01-01

This report describes laboratory procedures used by the U.S. Geological Survey Kentucky Water Science Center Sediment Laboratory for the processing and analysis of fluvial-sediment samples for concentration of sand and finer material. The report details the processing of a sediment sample through the laboratory from receiving the sediment sample, through the analytical process, to compiling results of the requested analysis. Procedures for preserving sample integrity, calibrating and maintaining of laboratory and field instruments and equipment, analyzing samples, internal quality assurance and quality control, and validity of the sediment-analysis results also are described. The report includes a list of references cited and a glossary of sediment and quality-assurance terms.

High Resolution Fabrication of Interconnection Lines Using Picosecond Laser and Controlled Deposition of Gold Nanoparticles

NASA Astrophysics Data System (ADS)

Shahmoon, Asaf; Strauß, Johnnes; Zafri, Hadar; Schmidt, Michael; Zalevsky, Zeev

In this paper we present the fabrication procedure as well as the preliminary experimental results of a novel method for construction of high resolution nanometric interconnection lines. The fabrication procedure relies on a self-assembly process of gold nanoparticles at specific predetermined nanostructures. The nanostructures for the self-assembly process are based on the focused ion beam (FIB) or scanning electron beam (SEM) technology. The assembled nanoparticles are being illuminated using a picosecond laser with a wavelength of 532 nm. Different pulse energies have been investigated. The paper aimed at developing a novel and reliable process for fabrication of interconnection lines encompass three different disciplines, self-assembly of nanometric particles, optics and microelectronic.

Biobanking of different body fluids within the frame of IVF-a standard operating procedure to improve reproductive biology research.

PubMed

Schenk, Michael; Huppertz, Berthold; Obermayer-Pietsch, Barbara; Kastelic, Darja; Hörmann-Kröpfl, Martina; Weiss, Gregor

2017-02-01

The aim of the present study was to develop a standard operating procedure (SOP) for the collection, transport, and storage of human cumulus cells, follicular fluid, blood serum, seminal plasma, embryo culture supernatant, and embryo culture supernatant control obtained within the IVF process under approved protocols and written informed consent from participating patients. The SOP was developed at the Kinderwunsch Institut Schenk, Dobl, Austria, together with Biobank Graz of the Medical University of Graz, Austria. The SOP provides comprehensive details of laboratory procedures and sampling of the different fluids within the IVF process. Furthermore, information on sample coding, references of involved laboratory techniques (e.g., oocyte retrieval with a Steiner-TAN needle), ethical approvals, and biobanking procedures are presented. The result of the present study is a standard operating procedure. The SOP ensures a professional way for collection and scientific use of IVF samples by the Kinderwunsch Institut Schenk, Dobl, Austria, and Biobank Graz of the Medical University of Graz, Austria. It can be used as a template for other institutions to unify specimen collection procedures in the field of reproductive health research.

Medical three-dimensional printing opens up new opportunities in cardiology and cardiac surgery.

PubMed

Bartel, Thomas; Rivard, Andrew; Jimenez, Alejandro; Mestres, Carlos A; Müller, Silvana

2018-04-14

Advanced percutaneous and surgical procedures in structural and congenital heart disease require precise pre-procedural planning and continuous quality control. Although current imaging modalities and post-processing software assists with peri-procedural guidance, their capabilities for spatial conceptualization remain limited in two- and three-dimensional representations. In contrast, 3D printing offers not only improved visualization for procedural planning, but provides substantial information on the accuracy of surgical reconstruction and device implantations. Peri-procedural 3D printing has the potential to set standards of quality assurance and individualized healthcare in cardiovascular medicine and surgery. Nowadays, a variety of clinical applications are available showing how accurate 3D computer reformatting and physical 3D printouts of native anatomy, embedded pathology, and implants are and how they may assist in the development of innovative therapies. Accurate imaging of pathology including target region for intervention, its anatomic features and spatial relation to the surrounding structures is critical for selecting optimal approach and evaluation of procedural results. This review describes clinical applications of 3D printing, outlines current limitations, and highlights future implications for quality control, advanced medical education and training.

Adaptive control of large space structures using recursive lattice filters

NASA Technical Reports Server (NTRS)

Goglia, G. L.

1985-01-01

The use of recursive lattice filters for identification and adaptive control of large space structures was studied. Lattice filters are used widely in the areas of speech and signal processing. Herein, they are used to identify the structural dynamics model of the flexible structures. This identified model is then used for adaptive control. Before the identified model and control laws are integrated, the identified model is passed through a series of validation procedures and only when the model passes these validation procedures control is engaged. This type of validation scheme prevents instability when the overall loop is closed. The results obtained from simulation were compared to those obtained from experiments. In this regard, the flexible beam and grid apparatus at the Aerospace Control Research Lab (ACRL) of NASA Langley Research Center were used as the principal candidates for carrying out the above tasks. Another important area of research, namely that of robust controller synthesis, was investigated using frequency domain multivariable controller synthesis methods.

SAR processing on the MPP

NASA Technical Reports Server (NTRS)

Batcher, K. E.; Eddey, E. E.; Faiss, R. O.; Gilmore, P. A.

1981-01-01

The processing of synthetic aperture radar (SAR) signals using the massively parallel processor (MPP) is discussed. The fast Fourier transform convolution procedures employed in the algorithms are described. The MPP architecture comprises an array unit (ARU) which processes arrays of data; an array control unit which controls the operation of the ARU and performs scalar arithmetic; a program and data management unit which controls the flow of data; and a unique staging memory (SM) which buffers and permutes data. The ARU contains a 128 by 128 array of bit-serial processing elements (PE). Two-by-four surarrays of PE's are packaged in a custom VLSI HCMOS chip. The staging memory is a large multidimensional-access memory which buffers and permutes data flowing with the system. Efficient SAR processing is achieved via ARU communication paths and SM data manipulation. Real time processing capability can be realized via a multiple ARU, multiple SM configuration.

Etching and Growth of GaAs

NASA Technical Reports Server (NTRS)

Seabaugh, A. C.; Mattauch, R., J.

1983-01-01

In-place process for etching and growth of gallium arsenide calls for presaturation of etch and growth melts by arsenic source crystal. Procedure allows precise control of thickness of etch and newly grown layer on substrate. Etching and deposition setup is expected to simplify processing and improve characteristics of gallium arsenide lasers, high-frequency amplifiers, and advanced integrated circuits.

10 CFR Appendix O to Part 110 - Illustrative List of Fuel Element Fabrication Plant Equipment and Components Under NRC's Export...

Code of Federal Regulations, 2010 CFR

2010-01-01

... performance and safety during reactor operation. Also, in all cases precise control of processes, procedures... elements include equipment that: (1) Normally comes in direct contact with, or directly processes or... pellets; (2) Automatic welding machines especially designed or prepared for welding end caps onto the fuel...

9 CFR 318.305 - Equipment and procedures for heat processing systems.

Code of Federal Regulations, 2010 CFR

2010-01-01

... control unit. A nonreturn valve shall be provided in the air supply line to prevent water from entering... control unit. A nonreturn valve shall be provided in the air supply line to prevent water from entering... ensure a supply of clean, dry air. The recorder timing mechanism shall be accurate. (i) Chart-type...

ISO 9002 as Literacy Practice: Coping with Quality-Control Documents in a High-Tech Company

ERIC Educational Resources Information Center

Kleifgen, Jo Anne

2005-01-01

This study describes the process by which a circuit board manufacturing company became certified in an international quality control program known as ISO 9002. Particular attention is paid to how quality documents were made and used in actual practice and to the relationship between these standardized procedures (official literacies) and…

40 CFR 65.158 - Performance test procedures for control devices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... simultaneously from multiple loading arms, each run shall represent at least one complete tank truck or tank car... the combustion air or as a secondary fuel into a boiler or process heater with a design capacity less... corrected to 3 percent oxygen if a combustion device is the control device. (A) The emission rate correction...

Line-Editor Computer Program

NASA Technical Reports Server (NTRS)

Scott, Peter J.

1989-01-01

ZED editing program for DEC VAX computer simple, powerful line editor for text, program source code, and nonbinary data. Excels in processing of text by use of procedure files. Also features versatile search qualifiers, global changes, conditionals, online help, hexadecimal mode, space compression, looping, logical combinations of search strings, journaling, visible control characters, and automatic detabbing. Users of Cambridge implementation devised such ZED procedures as chess games, calculators, and programs for evaluating pi. Written entirely in C.

Microstructure based procedure for process parameter control in rolling of aluminum thin foils

NASA Astrophysics Data System (ADS)

Johannes, Kronsteiner; Kabliman, Evgeniya; Klimek, Philipp-Christoph

2018-05-01

In present work, a microstructure based procedure is used for a numerical prediction of strength properties for Al-Mg-Sc thin foils during a hot rolling process. For this purpose, the following techniques were developed and implemented. At first, a toolkit for a numerical analysis of experimental stress-strain curves obtained during a hot compression testing by a deformation dilatometer was developed. The implemented techniques allow for the correction of a temperature increase in samples due to adiabatic heating and for the determination of a yield strength needed for the separation of the elastic and plastic deformation regimes during numerical simulation of multi-pass hot rolling. At the next step, an asymmetric Hot Rolling Simulator (adjustable table inlet/outlet height as well as separate roll infeed) was developed in order to match the exact processing conditions of a semi-industrial rolling procedure. At each element of a finite element mesh the total strength is calculated by in-house Flow Stress Model based on evolution of mean dislocation density. The strength values obtained by numerical modelling were found in a reasonable agreement with results of tensile tests for thin Al-Mg-Sc foils. Thus, the proposed simulation procedure might allow to optimize the processing parameters with respect to the microstructure development.

242A Distributed Control System Year 2000 Acceptance Test Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

TEATS, M.C.

1999-08-31

This report documents acceptance test results for the 242-A Evaporator distributive control system upgrade to D/3 version 9.0-2 for year 2000 compliance. This report documents the test results obtained by acceptance testing as directed by procedure HNF-2695. This verification procedure will document the initial testing and evaluation of the potential 242-A Distributed Control System (DCS) operating difficulties across the year 2000 boundary and the calendar adjustments needed for the leap year. Baseline system performance data will be recorded using current, as-is operating system software. Data will also be collected for operating system software that has been modified to correct yearmore » 2000 problems. This verification procedure is intended to be generic such that it may be performed on any D/3{trademark} (GSE Process Solutions, Inc.) distributed control system that runs with the VMSTM (Digital Equipment Corporation) operating system. This test may be run on simulation or production systems depending upon facility status. On production systems, DCS outages will occur nine times throughout performance of the test. These outages are expected to last about 10 minutes each.« less

Tuning algorithms for fractional order internal model controllers for time delay processes

NASA Astrophysics Data System (ADS)

Muresan, Cristina I.; Dutta, Abhishek; Dulf, Eva H.; Pinar, Zehra; Maxim, Anca; Ionescu, Clara M.

2016-03-01

This paper presents two tuning algorithms for fractional-order internal model control (IMC) controllers for time delay processes. The two tuning algorithms are based on two specific closed-loop control configurations: the IMC control structure and the Smith predictor structure. In the latter, the equivalency between IMC and Smith predictor control structures is used to tune a fractional-order IMC controller as the primary controller of the Smith predictor structure. Fractional-order IMC controllers are designed in both cases in order to enhance the closed-loop performance and robustness of classical integer order IMC controllers. The tuning procedures are exemplified for both single-input-single-output as well as multivariable processes, described by first-order and second-order transfer functions with time delays. Different numerical examples are provided, including a general multivariable time delay process. Integer order IMC controllers are designed in each case, as well as fractional-order IMC controllers. The simulation results show that the proposed fractional-order IMC controller ensures an increased robustness to modelling uncertainties. Experimental results are also provided, for the design of a multivariable fractional-order IMC controller in a Smith predictor structure for a quadruple-tank system.

High-Fidelity Single-Shot Toffoli Gate via Quantum Control.

PubMed

Zahedinejad, Ehsan; Ghosh, Joydip; Sanders, Barry C

2015-05-22

A single-shot Toffoli, or controlled-controlled-not, gate is desirable for classical and quantum information processing. The Toffoli gate alone is universal for reversible computing and, accompanied by the Hadamard gate, forms a universal gate set for quantum computing. The Toffoli gate is also a key ingredient for (nontopological) quantum error correction. Currently Toffoli gates are achieved by decomposing into sequentially implemented single- and two-qubit gates, which require much longer times and yields lower overall fidelities compared to a single-shot implementation. We develop a quantum-control procedure to construct a single-shot Toffoli gate for three nearest-neighbor-coupled superconducting transmon systems such that the fidelity is 99.9% and is as fast as an entangling two-qubit gate under the same realistic conditions. The gate is achieved by a nongreedy quantum control procedure using our enhanced version of the differential evolution algorithm.

Infrared Sensor-Based Temperature Control for Domestic Induction Cooktops

PubMed Central

Lasobras, Javier; Alonso, Rafael; Carretero, Claudio; Carretero, Enrique; Imaz, Eduardo

2014-01-01

In this paper, a precise real-time temperature control system based on infrared (IR) thermometry for domestic induction cooking is presented. The temperature in the vessel constitutes the control variable of the closed-loop power control system implemented in a commercial induction cooker. A proportional-integral controller is applied to establish the output power level in order to reach the target temperature. An optical system and a signal conditioning circuit have been implemented. For the signal processing a microprocessor with 12-bit ADC and a sampling rate of 1 Ksps has been used. The analysis of the contributions to the infrared radiation permits the definition of a procedure to estimate the temperature of the vessel with a maximum temperature error of 5 °C in the range between 60 and 250 °C for a known cookware emissivity. A simple and necessary calibration procedure with a black-body sample is presented. PMID:24638125

Infrared sensor-based temperature control for domestic induction cooktops.

PubMed

Lasobras, Javier; Alonso, Rafael; Carretero, Claudio; Carretero, Enrique; Imaz, Eduardo

2014-03-14

In this paper, a precise real-time temperature control system based on infrared (IR) thermometry for domestic induction cooking is presented. The temperature in the vessel constitutes the control variable of the closed-loop power control system implemented in a commercial induction cooker. A proportional-integral controller is applied to establish the output power level in order to reach the target temperature. An optical system and a signal conditioning circuit have been implemented. For the signal processing a microprocessor with 12-bit ADC and a sampling rate of 1 Ksps has been used. The analysis of the contributions to the infrared radiation permits the definition of a procedure to estimate the temperature of the vessel with a maximum temperature error of 5 °C in the range between 60 and 250 °C for a known cookware emissivity. A simple and necessary calibration procedure with a black-body sample is presented.

Report: EPA Needs to Strengthen Internal Controls for Determining Workforce Levels

EPA Pesticide Factsheets

Report #11-P-0031, December 20, 2010. EPA’s policies and procedures do not include a process for determining employment levels based on workload as prescribed by the Office of Management and Budget.

NAFTA Revised Procedures for Joint Review of Microbials and Semiochemicals

EPA Pesticide Factsheets

The Canadian Pest Management Regulatory Agency and EPA have established a process for the joint review of pest control products in which the new active ingredient is a microbial or an arthropod semiochemical (including pheromones).

Scalable software-defined optical networking with high-performance routing and wavelength assignment algorithms.

PubMed

Lee, Chankyun; Cao, Xiaoyuan; Yoshikane, Noboru; Tsuritani, Takehiro; Rhee, June-Koo Kevin

2015-10-19

The feasibility of software-defined optical networking (SDON) for a practical application critically depends on scalability of centralized control performance. The paper, highly scalable routing and wavelength assignment (RWA) algorithms are investigated on an OpenFlow-based SDON testbed for proof-of-concept demonstration. Efficient RWA algorithms are proposed to achieve high performance in achieving network capacity with reduced computation cost, which is a significant attribute in a scalable centralized-control SDON. The proposed heuristic RWA algorithms differ in the orders of request processes and in the procedures of routing table updates. Combined in a shortest-path-based routing algorithm, a hottest-request-first processing policy that considers demand intensity and end-to-end distance information offers both the highest throughput of networks and acceptable computation scalability. We further investigate trade-off relationship between network throughput and computation complexity in routing table update procedure by a simulation study.

Virtually Out of This World!

NASA Technical Reports Server (NTRS)

2002-01-01

Ames Research Center granted Reality Capture Technologies (RCT), Inc., a license to further develop NASA's Mars Map software platform. The company incorporated NASA#s innovation into software that uses the Virtual Plant Model (VPM)(TM) to structure, modify, and implement the construction sites of industrial facilities, as well as develop, validate, and train operators on procedures. The VPM orchestrates the exchange of information between engineering, production, and business transaction systems. This enables users to simulate, control, and optimize work processes while increasing the reliability of critical business decisions. Engineers can complete the construction process and test various aspects of it in virtual reality before building the actual structure. With virtual access to and simulation of the construction site, project personnel can manage, access control, and respond to changes on complex constructions more effectively. Engineers can also create operating procedures, training, and documentation. Virtual Plant Model(TM) is a trademark of Reality Capture Technologies, Inc.

Applied Research Study

NASA Technical Reports Server (NTRS)

Leach, Ronald J.

1997-01-01

The purpose of this project was to study the feasibility of reusing major components of a software system that had been used to control the operations of a spacecraft launched in the 1980s. The study was done in the context of a ground data processing system that was to be rehosted from a large mainframe to an inexpensive workstation. The study concluded that a systematic approach using inexpensive tools could aid in the reengineering process by identifying a set of certified reusable components. The study also developed procedures for determining duplicate versions of software, which were created because of inadequate naming conventions. Such procedures reduced reengineering costs by approximately 19.4 percent.

Monitoring copper release in drinking water distribution systems.

PubMed

d'Antonio, L; Fabbricino, M; Panico, A

2008-01-01

A new procedure, recently proposed for on-line monitoring of copper released from metal pipes in household plumbing system for drinking water distribution during the development of corrosion processes, is tested experimentally. Experiments were carried out in laboratory controlled conditions, using synthetic water and varying the water alkalinity. The possibility of using the corrosion potential as a surrogate measure of copper concentration in stagnating water is shown, verifying, in the meantime, the effect of alkalinity on the development of passivation phenomena, which tend to protect the pipe from corrosion processes. Experimental data are discussed, highlighting the potentiality of the procedure, and recognizing its limitations. Copyright IWA Publishing 2008.

Bioactive Molecule Delivery Systems for Dentin-pulp Tissue Engineering.

PubMed

Shrestha, Suja; Kishen, Anil

2017-05-01

Regenerative endodontic procedures use bioactive molecules (BMs), which are active signaling molecules that initiate and maintain cell responses and interactions. When applied in a bolus form, they may undergo rapid diffusion and denaturation resulting in failure to induce the desired effects on target cells. The controlled release of BMs from a biomaterial carrier is expected to enhance and accelerate functional tissue engineering during regenerative endodontic procedures. This narrative review presents a comprehensive review of different polymeric BM release strategies with relevance to dentin-pulp engineering. Carrier systems designed to allow the preprogrammed release of BMs in a spatial- and temporal-controlled manner would aid in mimicking the natural wound healing process while overcoming some of the challenges faced in clinical translation of regenerative endodontic procedures. Spatial- and temporal-controlled BM release systems have become an exciting option in dentin-pulp tissue engineering; nonetheless, further validation of this concept and knowledge is required for their potential clinical translation. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Mutagen Sensitivity, Apoptosis, and Polymorphism in DNA Repair as Measures of Prostate Cancer Risk

DTIC Science & Technology

2005-02-01

blood tubes are immediately refrigerated and delivered on ice within 6 hours to the GCRC core facility at Georgetown University for processing . Case...is CLIA certified. There is a centrally monitored storage facility with -80’C freezers. The established recruitment and optimized sample processing in...controls. We have established the recruitment procedures, sample collection, processing , repository, and data management. This is a substantial effort

Management control and status reports documentation standard and Data Item Descriptions (DID). Volume of the information system life-cycle and documentation standards, volume 5

NASA Technical Reports Server (NTRS)

Callender, E. David; Steinbacher, Jody

1989-01-01

This is the fifth of five volumes on Information System Life-Cycle and Documentation Standards. This volume provides a well organized, easily used standard for management control and status reports used in monitoring and controlling the management, development, and assurance of informations systems and software, hardware, and operational procedures components, and related processes.

High-Performance Substrates for SERS Detection via Microphotonic Photopolymer Characterization and Coating With Functionalized Hydrogels

DTIC Science & Technology

2006-11-26

with controlled micro and nanostructure for highly selective, high sensitivity assays. The process was modeled and a procedure for fabricating SERS...small volumes with controlled micro and nanostructure for highly selective, high sensitivity assays. We proved the feasibility of the technique and...films templated by colloidal crystals. The control over the film structure allowed optimizing their performance for potential sensor applications. The

Conference Proceedings: Aptitude, Learning, and Instruction. Volume 1. Cognitive Process Analyses of Aptitude,

DTIC Science & Technology

1981-01-01

errors more than twice that shown by the control group (32% versus 13%). The quantitative difference between training and control groups was further...could be enhanced (relative to control groups ) by means of brief training procedures. Educational implications of metaphor research were considered, with...instruction: It addresses itself to the kinds of research and instructional designs required for effective implementation of adaptive instruction ONR

Strategies for concurrent processing of complex algorithms in data driven architectures

NASA Technical Reports Server (NTRS)

Stoughton, John W.; Mielke, Roland R.; Som, Sukhamony

1990-01-01

The performance modeling and enhancement for periodic execution of large-grain, decision-free algorithms in data flow architectures is examined. Applications include real-time implementation of control and signal processing algorithms where performance is required to be highly predictable. The mapping of algorithms onto the specified class of data flow architectures is realized by a marked graph model called ATAMM (Algorithm To Architecture Mapping Model). Performance measures and bounds are established. Algorithm transformation techniques are identified for performance enhancement and reduction of resource (computing element) requirements. A systematic design procedure is described for generating operating conditions for predictable performance both with and without resource constraints. An ATAMM simulator is used to test and validate the performance prediction by the design procedure. Experiments on a three resource testbed provide verification of the ATAMM model and the design procedure.

Strategies for concurrent processing of complex algorithms in data driven architectures

NASA Technical Reports Server (NTRS)

Som, Sukhamoy; Stoughton, John W.; Mielke, Roland R.

1990-01-01

Performance modeling and performance enhancement for periodic execution of large-grain, decision-free algorithms in data flow architectures are discussed. Applications include real-time implementation of control and signal processing algorithms where performance is required to be highly predictable. The mapping of algorithms onto the specified class of data flow architectures is realized by a marked graph model called algorithm to architecture mapping model (ATAMM). Performance measures and bounds are established. Algorithm transformation techniques are identified for performance enhancement and reduction of resource (computing element) requirements. A systematic design procedure is described for generating operating conditions for predictable performance both with and without resource constraints. An ATAMM simulator is used to test and validate the performance prediction by the design procedure. Experiments on a three resource testbed provide verification of the ATAMM model and the design procedure.

Antenna Linear-Quadratic-Gaussian (LQG) Controllers: Properties, Limits of Performance, and Tuning Procedure

NASA Technical Reports Server (NTRS)

Gawronski, W.

2004-01-01

Wind gusts are the main disturbances that depreciate tracking precision of microwave antennas and radiotelescopes. The linear-quadratic-Gaussian (LQG) controllers - as compared with the proportional-and-integral (PI) controllers significantly improve the tracking precision in wind disturbances. However, their properties have not been satisfactorily understood; consequently, their tuning is a trial-and-error process. A control engineer has two tools to tune an LQG controller: the choice of coordinate system of the controller model and the selection of weights of the LQG performance index. This article analyzes properties of an open- and closed-loop antenna. It shows that the proper choice of coordinates of the open-loop model simplifies the shaping of the closed-loop performance. The closed-loop properties are influenced by the LQG weights. The article shows the impact of the weights on the antenna closed-loop bandwidth, disturbance rejection properties, and antenna acceleration. The bandwidth and the disturbance rejection characterize the antenna performance, while the acceleration represents the performance limit set by the antenna hardware (motors). The article presents the controller tuning procedure, based on the coordinate selection and the weight properties. The procedure rationally shapes the closed-loop performance, as an alternative to the trial-and-error approach.

Automatic and controlled components of judgment and decision making.

PubMed

Ferreira, Mario B; Garcia-Marques, Leonel; Sherman, Steven J; Sherman, Jeffrey W

2006-11-01

The categorization of inductive reasoning into largely automatic processes (heuristic reasoning) and controlled analytical processes (rule-based reasoning) put forward by dual-process approaches of judgment under uncertainty (e.g., K. E. Stanovich & R. F. West, 2000) has been primarily a matter of assumption with a scarcity of direct empirical findings supporting it. The present authors use the process dissociation procedure (L. L. Jacoby, 1991) to provide convergent evidence validating a dual-process perspective to judgment under uncertainty based on the independent contributions of heuristic and rule-based reasoning. Process dissociations based on experimental manipulation of variables were derived from the most relevant theoretical properties typically used to contrast the two forms of reasoning. These include processing goals (Experiment 1), cognitive resources (Experiment 2), priming (Experiment 3), and formal training (Experiment 4); the results consistently support the author's perspective. They conclude that judgment under uncertainty is neither an automatic nor a controlled process but that it reflects both processes, with each making independent contributions.

Development of automation software for neutron activation analysis process in Malaysian nuclear agency

NASA Astrophysics Data System (ADS)

Yussup, N.; Rahman, N. A. A.; Ibrahim, M. M.; Mokhtar, M.; Salim, N. A. A.; Soh@Shaari, S. C.; Azman, A.

2017-01-01

Neutron Activation Analysis (NAA) process has been established in Malaysian Nuclear Agency (Nuclear Malaysia) since 1980s. Most of the procedures established especially from sample registration to sample analysis are performed manually. These manual procedures carried out by the NAA laboratory personnel are time consuming and inefficient. Hence, a software to support the system automation is developed to provide an effective method to replace redundant manual data entries and produce faster sample analysis and calculation process. This paper describes the design and development of automation software for NAA process which consists of three sub-programs. The sub-programs are sample registration, hardware control and data acquisition; and sample analysis. The data flow and connection between the sub-programs will be explained. The software is developed by using National Instrument LabView development package.

Proceedings of the Annual Symposium on Frequency Control (37th). 1-3 June 1983, Marriott Hotel, Philadelphia, Pennsylvania.

DTIC Science & Technology

1983-06-03

current not power. inspection groups . The experimental procedure for the resistance TABLE I non -linearity inspection will be to condition the crystal...comparatively small [24]. By eali effect, the precision with which the effect micht controlling the experimental conditions we estimate be controlled ...intended to be a accepted on an individual basis for Group A predictor of long term performance. It is another testing. check on process control

Universal photonic quantum gates assisted by ancilla diamond nitrogen-vacancy centers coupled to resonators

NASA Astrophysics Data System (ADS)

Wei, Hai-Rui; Long, Gui Lu

2015-03-01

We propose two compact, economic, and scalable schemes for implementing optical controlled-phase-flip and controlled-controlled-phase-flip gates by using the input-output process of a single-sided cavity strongly coupled to a single nitrogen-vacancy-center defect in diamond. Additional photonic qubits, necessary for procedures based on the parity-check measurement or controlled-path and merging gates, are not employed in our schemes. In the controlled-path gate, the paths of the target photon are conditionally controlled by the control photon, and these two paths can be merged back into one by using a merging gate. Only one half-wave plate is employed in our scheme for the controlled-phase-flip gate. Compared with the conventional synthesis procedures for constructing a controlled-controlled-phase-flip gate, the cost of which is two controlled-path gates and two merging gates, or six controlled-not gates, our scheme is more compact and simpler. Our schemes could be performed with a high fidelity and high efficiency with current achievable experimental techniques.

Experience with soluble neutron poisons for criticality control at ICPP

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, R.E.; Mortimer, S.R.

1978-01-01

Soluble neutron poisons assure criticality control in two of the headend fuel reprocessing systems at the Idaho Chemical Processing Plant. Soluble poisons have been used successfully since 1964 and will be employed in the projected new headend processes. The use of soluble poisons (1) greatly increases the process output (2) allows versatility in the size of fuel assemblies processed and (3) allows the practical reprocessing of some fuels. The safety limit for all fluids entering the U-Zr alloy dissolver is 3.6 g/liter boron. To allow for possible deviations in the measurement systems and drift between analytical sampling periods, the standardmore » practice is to use 3.85 g/liter boron as the lower limit. This dissolver has had 4000 successful hours of operation using soluble poisons. The electrolytic dissolution process depends on soluble gadolinium for criticality safety. This system is used to process high enriched uranium clad in stainless steel. Electrolytic dissolution takes advantage of the anodic corrosion that occurs when a large electrical current is passed through the fuel elements in a corrosive environment. Three control methods are used on each headend system. First, the poison is mixed according to standard operating procedures and the measurements are affirmed by the operator's supervisor. Second, the poisoned solution is stirred, sampled, analyzed, and the analysis reported while still in the mix tank. Finally, a Nuclear Poison Detection System (NPDS) must show an acceptable poison concentration before the solution can be transferred. The major disadvantage of using soluble poisons is the need for very sophisticated control systems and procedures, which require extensive checkout. The need for a poisoned primary heating and cooling system means a secondary system is needed as well. Experience has shown, however, that production enhancement more than makes up for the problems.« less

Micro-scale experimental study of Microbial-Induced Carbonate Precipitation (MICP) by using microfluidic devices

NASA Astrophysics Data System (ADS)

Wang, Y.; Soga, K.; DeJong, J. T.; Kabla, A.

2017-12-01

Microbial-induced carbonate precipitation (MICP), one of the bio-mineralization processes, is an innovative subsurface improvement technique for enhancing the strength and stiffness of soils, and controlling their hydraulic conductivity. These macro-scale engineering properties of MICP treated soils controlled by micro-scale factors of the precipitated carbonate, such as its content, amount and distribution in the soil matrix. The precipitation process itself is affected by bacteria amount, reaction kinetics, porous medium geometry and flow distribution in the soils. Accordingly, to better understand the MICP process at the pore scale a new experimental technique that can observe the entire process of MICP at the pore-scale was developed. In this study, a 2-D transparent microfluidic chip made of Polydimethylsiloxane (PDMS) representing the soil matrix was designed and fabricated. A staged-injection MICP treatment procedure was simulated inside the microfluidic chip while continuously monitored using microscopic techniques. The staged-injection MICP treatment procedure started with the injection of bacteria suspension, followed with the bacteria setting for attachment, and then ended with the multiple injections of cementation liquid. The main MICP processes visualized during this procedure included the bacteria transport and attachment during the bacteria injection, the bacteria attachment and growth during the bacteria settling, the bacteria detachment during the cementation liquid injection, the cementation development during the cementation liquid injection, and the cementation development after the completion of cementation liquid injection. It is suggested that the visualization of the main MICP processes using the microfluidic technique can improve understating of the fundamental mechanisms of MICP and consequently help improve the treatment technique for in situ implementation of MICP.

Statistical Methods in Assembly Quality Management of Multi-Element Products on Automatic Rotor Lines

NASA Astrophysics Data System (ADS)

Pries, V. V.; Proskuriakov, N. E.

2018-04-01

To control the assembly quality of multi-element mass-produced products on automatic rotor lines, control methods with operational feedback are required. However, due to possible failures in the operation of the devices and systems of automatic rotor line, there is always a real probability of getting defective (incomplete) products into the output process stream. Therefore, a continuous sampling control of the products completeness, based on the use of statistical methods, remains an important element in managing the quality of assembly of multi-element mass products on automatic rotor lines. The feature of continuous sampling control of the multi-element products completeness in the assembly process is its breaking sort, which excludes the possibility of returning component parts after sampling control to the process stream and leads to a decrease in the actual productivity of the assembly equipment. Therefore, the use of statistical procedures for continuous sampling control of the multi-element products completeness when assembled on automatic rotor lines requires the use of such sampling plans that ensure a minimum size of control samples. Comparison of the values of the limit of the average output defect level for the continuous sampling plan (CSP) and for the automated continuous sampling plan (ACSP) shows the possibility of providing lower limit values for the average output defects level using the ACSP-1. Also, the average sample size when using the ACSP-1 plan is less than when using the CSP-1 plan. Thus, the application of statistical methods in the assembly quality management of multi-element products on automatic rotor lines, involving the use of proposed plans and methods for continuous selective control, will allow to automating sampling control procedures and the required level of quality of assembled products while minimizing sample size.

Quality-Assurance Data for Routine Water Analyses by the U.S. Geological Survey Laboratory in Troy, New York - July 2001 Through June 2003

USGS Publications Warehouse

Lincoln, Tricia A.; Horan-Ross, Debra A.; McHale, Michael R.; Lawrence, Gregory B.

2009-01-01

The laboratory for analysis of low-ionic-strength water at the U.S. Geological Survey (USGS) Water Science Center in Troy, N.Y., analyzes samples collected by USGS projects throughout the Northeast. The laboratory's quality-assurance program is based on internal and interlaboratory quality-assurance samples and quality-control procedures that were developed to ensure proper sample collection, processing, and analysis. The quality-assurance and quality-control data were stored in the laboratory's Lab Master data-management system, which provides efficient review, compilation, and plotting of data. This report presents and discusses results of quality-assurance and quality control samples analyzed from July 2001 through June 2003. Results for the quality-control samples for 19 analytical procedures were evaluated for bias and precision. Control charts indicate that data for six of the analytical procedures were occasionally biased for either high-concentration or low-concentration samples but were within control limits; these procedures were: acid-neutralizing capacity, chloride, magnesium, nitrate (ion chromatography), potassium, and sodium. The calcium procedure was biased throughout the analysis period for the high-concentration sample, but was within control limits. The total monomeric aluminum and fluoride procedures were biased throughout the analysis period for the low-concentration sample, but were within control limits. The total aluminum, pH, specific conductance, and sulfate procedures were biased for the high-concentration and low-concentration samples, but were within control limits. Results from the filter-blank and analytical-blank analyses indicate that the procedures for 16 of 18 analytes were within control limits, although the concentrations for blanks were occasionally outside the control limits. The data-quality objective was not met for the dissolved organic carbon or specific conductance procedures. Sampling and analysis precision are evaluated herein in terms of the coefficient of variation obtained for triplicate samples in the procedures for 18 of the 21 analytes. At least 90 percent of the samples met data-quality objectives for all procedures except total monomeric aluminum (83 percent of samples met objectives), total aluminum (76 percent of samples met objectives), ammonium (73 percent of samples met objectives), dissolved organic carbon (86 percent of samples met objectives), and nitrate (81 percent of samples met objectives). The data-quality objective was not met for the nitrite procedure. Results of the USGS interlaboratory Standard Reference Sample (SRS) Project indicated satisfactory or above data quality over the time period, with most performance ratings for each sample in the good-to-excellent range. The N-sample (nutrient constituents) analysis had one unsatisfactory rating for the ammonium procedure in one study. The T-sample (trace constituents) analysis had one unsatisfactory rating for the magnesium procedure and one marginal rating for the potassium procedure in one study and one unsatisfactory rating for the sodium procedure in another. Results of Environment Canada's National Water Research Institute (NWRI) program indicated that at least 90 percent of the samples met data-quality objectives for 10 of the 14 analytes; the exceptions were acid-neutralizing capacity, ammonium, dissolved organic carbon, and sodium. Data-quality objectives were not met in 37 percent of samples analyzed for acid-neutralizing capacity, 28 percent of samples analyzed for dissolved organic carbon, and 30 percent of samples analyzed for sodium. Results indicate a positive bias for the ammonium procedure in one study and a negative bias in another. Results from blind reference-sample analyses indicated that data-quality objectives were met by at least 90 percent of the samples analyzed for calcium, chloride, magnesium, pH, potassium, and sodium. Data-quality objectives were met by 78 percent of

Recollection and familiarity in amnesic mild cognitive impairment.

PubMed

Serra, Laura; Bozzali, Marco; Cercignani, Mara; Perri, Roberta; Fadda, Lucia; Caltagirone, Carlo; Carlesimo, Giovanni A

2010-05-01

To investigate whether, in patients with amnesic mild cognitive impairment (a-MCI), recognition deficits are mainly due to a selective impairment of recollection rather than familiarity. Nineteen patients with a-MCI and 23 sex-, age-, and education-matched healthy controls underwent two experimental investigations, using the Process Dissociation Procedure (PDP) and the Remember/Know (R/K) procedure, to assess the differential contribution of recollection and familiarity to their recognition performance. Both experimental procedures revealed a selective preservation of familiarity in a-MCI patients. Moreover, the R/K procedure showed a statistically significant impairment of recollection in a-MCI patients for words that were either read or anagrammed during the study phase. A-MCI is known to be commonly associated with a high risk of conversion to Alzheimer's disease (AD). Several previous studies have demonstrated a characteristic impairment of episodic memory in a-MCI, with an early dysfunction of recognition. Our findings are consistent with the knowledge of neurodegeneration occurring in AD, which is characterized, at the earliest disease stages, by a selective involvement of the entorhinal cortex. Moreover, the current study supports the dual process model of recognition, which hypothesizes recollection and familiarity to be independent processes associated with distinct anatomical substrates.

Quality-Assurance Data for Routine Water Analyses by the U.S. Geological Survey Laboratory in Troy, New York--July 1999 through June 2001

USGS Publications Warehouse

Lincoln, Tricia A.; Horan-Ross, Debra A.; McHale, Michael R.; Lawrence, Gregory B.

2006-01-01

The laboratory for analysis of low-ionic-strength water at the U.S. Geological Survey (USGS) Water Science Center in Troy, N.Y., analyzes samples collected by USGS projects throughout the Northeast. The laboratory's quality-assurance program is based on internal and interlaboratory quality-assurance samples and quality-control procedures that were developed to ensure proper sample collection, processing, and analysis. The quality-assurance and quality-control data were stored in the laboratory's LabMaster data-management system, which provides efficient review, compilation, and plotting of data. This report presents and discusses results of quality-assurance and quality-control samples analyzed from July 1999 through June 2001. Results for the quality-control samples for 18 analytical procedures were evaluated for bias and precision. Control charts indicate that data for eight of the analytical procedures were occasionally biased for either high-concentration or low-concentration samples but were within control limits; these procedures were: acid-neutralizing capacity, total monomeric aluminum, total aluminum, calcium, chloride and nitrate (ion chromatography and colormetric method) and sulfate. The total aluminum and dissolved organic carbon procedures were biased throughout the analysis period for the high-concentration sample, but were within control limits. The calcium and specific conductance procedures were biased throughout the analysis period for the low-concentration sample, but were within control limits. The magnesium procedure was biased for the high-concentration and low concentration samples, but was within control limits. Results from the filter-blank and analytical-blank analyses indicate that the procedures for 14 of 15 analytes were within control limits, although the concentrations for blanks were occasionally outside the control limits. The data-quality objective was not met for dissolved organic carbon. Sampling and analysis precision are evaluated herein in terms of the coefficient of variation obtained for triplicate samples in the procedures for 17 of the 18 analytes. At least 90 percent of the samples met data-quality objectives for all analytes except ammonium (81 percent of samples met objectives), chloride (75 percent of samples met objectives), and sodium (86 percent of samples met objectives). Results of the USGS interlaboratory Standard Reference Sample (SRS) Project indicated good data quality over the time period, with most ratings for each sample in the good to excellent range. The P-sample (low-ionic-strength constituents) analysis had one satisfactory rating for the specific conductance procedure in one study. The T-sample (trace constituents) analysis had one satisfactory rating for the aluminum procedure in one study and one unsatisfactory rating for the sodium procedure in another. The remainder of the samples had good or excellent ratings for each study. Results of Environment Canada's National Water Research Institute (NWRI) program indicated that at least 89 percent of the samples met data-quality objectives for 10 of the 14 analytes; the exceptions were ammonium, total aluminum, dissolved organic carbon, and sodium. Results indicate a positive bias for the ammonium procedure in all studies. Data-quality objectives were not met in 50 percent of samples analyzed for total aluminum, 38 percent of samples analyzed for dissolved organic carbon, and 27 percent of samples analyzed for sodium. Results from blind reference-sample analyses indicated that data-quality objectives were met by at least 91 percent of the samples analyzed for calcium, chloride, fluoride, magnesium, pH, potassium, and sulfate. Data-quality objectives were met by 75 percent of the samples analyzed for sodium and 58 percent of the samples analyzed for specific conductance.

AMO EXPRESS: A Command and Control Experiment for Crew Autonomy Onboard the International Space Station

NASA Technical Reports Server (NTRS)

Stetson, Howard K.; Haddock, Angie T.; Frank, Jeremy; Cornelius, Randy; Wang, Lui; Garner, Larry

2015-01-01

NASA is investigating a range of future human spaceflight missions, including both Mars-distance and Near Earth Object (NEO) targets. Of significant importance for these missions is the balance between crew autonomy and vehicle automation. As distance from Earth results in increasing communication delays, future crews need both the capability and authority to independently make decisions. However, small crews cannot take on all functions performed by ground today, and so vehicles must be more automated to reduce the crew workload for such missions. NASA's Advanced Exploration Systems Program funded Autonomous Mission Operations (AMO) project conducted an autonomous command and control experiment on-board the International Space Station that demonstrated single action intelligent procedures for crew command and control. The target problem was to enable crew initialization of a facility class rack with power and thermal interfaces, and involving core and payload command and telemetry processing, without support from ground controllers. This autonomous operations capability is enabling in scenarios such as initialization of a medical facility to respond to a crew medical emergency, and representative of other spacecraft autonomy challenges. The experiment was conducted using the Expedite the Processing of Experiments for Space Station (EXPRESS) rack 7, which was located in the Port 2 location within the U.S Laboratory onboard the International Space Station (ISS). Activation and deactivation of this facility is time consuming and operationally intensive, requiring coordination of three flight control positions, 47 nominal steps, 57 commands, 276 telemetry checks, and coordination of multiple ISS systems (both core and payload). Utilization of Draper Laboratory's Timeliner software, deployed on-board the ISS within the Command and Control (C&C) computers and the Payload computers, allowed development of the automated procedures specific to ISS without having to certify and employ novel software for procedure development and execution. The procedures contained the ground procedure logic and actions as possible to include fault detection and recovery capabilities. The autonomous operations concept includes a reduction of the amount of data a crew operator is required to verify during activation or de-activation, as well as integration of procedure execution status and relevant data in a single integrated display. During execution, the auto-procedures (via Timerliner) provide a step-by-step messaging paradigm and a high-level status upon termination. This messaging and high-level status is the only data generated for operator display. To enhance situational awareness of the operator, the Web-based Procedure Display (WebPD) provides a novel approach to the issues of procedure display and execution tracking. WebPD is a web based application that serves as the user interface for electronic procedure execution. It incorporates several aspects of the HTML5 standard. Procedures are written in a dialect of XML called Procedure Representation Language (PRL). WebPD tracks execution status in the procedure or procedures being displayed. WebPD aggregates and simplifies the auto-sequence execution status information, and formatted to be easily followed and understood by an operator who is not dedicated to actively monitoring the task. WebPD also provides an integrated data and control interface to pause or halt the execution in order to provide a check point of operation and to examine progress before starting the next sequence of activities. For this demonstration, the procedure was initiated and monitored from the ground. As the Timeliner sequences executed, their high-level execution status was written to PLMDM memory. This memory is read and downlinked via Ku-Band at a 1 Hz rate. The data containing the high-level execution status is de-commutated on the ground, and rebroadcast for WebPD consumption. A future demonstration will be performed onboard, with ISS astronauts initiating the operations instead of ground controllers. The AMO EXPRESS experiment demonstrated activation and de-activation of EXPRESS rack 7, providing the capability of future single button activations and deactivations of facility class racks. The experiment achieved numerous technical and operations 'firsts' for the ISS

Cascade control of superheated steam temperature with neuro-PID controller.

PubMed

Zhang, Jianhua; Zhang, Fenfang; Ren, Mifeng; Hou, Guolian; Fang, Fang

2012-11-01

In this paper, an improved cascade control methodology for superheated processes is developed, in which the primary PID controller is implemented by neural networks trained by minimizing error entropy criterion. The entropy of the tracking error can be estimated recursively by utilizing receding horizon window technique. The measurable disturbances in superheated processes are input to the neuro-PID controller besides the sequences of tracking error in outer loop control system, hence, feedback control is combined with feedforward control in the proposed neuro-PID controller. The convergent condition of the neural networks is analyzed. The implementation procedures of the proposed cascade control approach are summarized. Compared with the neuro-PID controller using minimizing squared error criterion, the proposed neuro-PID controller using minimizing error entropy criterion may decrease fluctuations of the superheated steam temperature. A simulation example shows the advantages of the proposed method. Copyright © 2012 ISA. Published by Elsevier Ltd. All rights reserved.

21 CFR 111.153 - What are the requirements under this subpart G for written procedures?

Code of Federal Regulations, 2012 CFR

2012-04-01

... MANUFACTURING, PACKAGING, LABELING, OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control... or Labeling as a Dietary Supplement § 111.153 What are the requirements under this subpart G for...

21 CFR 111.153 - What are the requirements under this subpart G for written procedures?

Code of Federal Regulations, 2013 CFR

2013-04-01

... MANUFACTURING, PACKAGING, LABELING, OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control... or Labeling as a Dietary Supplement § 111.153 What are the requirements under this subpart G for...

21 CFR 111.153 - What are the requirements under this subpart G for written procedures?

Code of Federal Regulations, 2014 CFR

2014-04-01

... MANUFACTURING, PACKAGING, LABELING, OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control... or Labeling as a Dietary Supplement § 111.153 What are the requirements under this subpart G for...

21 CFR 111.153 - What are the requirements under this subpart G for written procedures?

Code of Federal Regulations, 2011 CFR

2011-04-01

... MANUFACTURING, PACKAGING, LABELING, OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control... or Labeling as a Dietary Supplement § 111.153 What are the requirements under this subpart G for...

21 CFR 111.153 - What are the requirements under this subpart G for written procedures?

Code of Federal Regulations, 2010 CFR

2010-04-01

... MANUFACTURING, PACKAGING, LABELING, OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control... or Labeling as a Dietary Supplement § 111.153 What are the requirements under this subpart G for...

Testing guide for implementing concrete paving quality control procedures.

DOT National Transportation Integrated Search

2008-03-01

Construction of portland cement concrete pavements is a complex process. A small fraction of the concrete pavements constructed in the : United States over the last few decades have either failed prematurely or exhibited moderate to severe distress. ...

[Controlling instruments in radiology].

PubMed

Maurer, M

2013-10-01

Due to the rising costs and competitive pressures radiological clinics and practices are now facing, controlling instruments are gaining importance in the optimization of structures and processes of the various diagnostic examinations and interventional procedures. It will be shown how the use of selected controlling instruments can secure and improve the performance of radiological facilities. A definition of the concept of controlling will be provided. It will be shown which controlling instruments can be applied in radiological departments and practices. As an example, two of the controlling instruments, material cost analysis and benchmarking, will be illustrated.

A Method for Implementing Force-Limited Vibration Control

NASA Technical Reports Server (NTRS)

Worth, Daniel B.

1997-01-01

NASA/GSFC has implemented force-limited vibration control on a controller which can only accept one profile. The method uses a personal computer based digital signal processing board to convert force and/or moment signals into what appears to he an acceleration signal to the controller. This technique allows test centers with older controllers to use the latest force-limited control techniques for random vibration testing. The paper describes the method, hardware, and test procedures used. An example from a test performed at NASA/GSFC is used as a guide.

Analytical design of an industrial two-term controller for optimal regulatory control of open-loop unstable processes under operational constraints.

PubMed

Tchamna, Rodrigue; Lee, Moonyong

2018-01-01

This paper proposes a novel optimization-based approach for the design of an industrial two-term proportional-integral (PI) controller for the optimal regulatory control of unstable processes subjected to three common operational constraints related to the process variable, manipulated variable and its rate of change. To derive analytical design relations, the constrained optimal control problem in the time domain was transformed into an unconstrained optimization problem in a new parameter space via an effective parameterization. The resulting optimal PI controller has been verified to yield optimal performance and stability of an open-loop unstable first-order process under operational constraints. The proposed analytical design method explicitly takes into account the operational constraints in the controller design stage and also provides useful insights into the optimal controller design. Practical procedures for designing optimal PI parameters and a feasible constraint set exclusive of complex optimization steps are also proposed. The proposed controller was compared with several other PI controllers to illustrate its performance. The robustness of the proposed controller against plant-model mismatch has also been investigated. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Analysis of verbal communication during teaching in the operating room and the potentials for surgical training.

PubMed

Blom, E M; Verdaasdonk, E G G; Stassen, L P S; Stassen, H G; Wieringa, P A; Dankelman, J

2007-09-01

Verbal communication in the operating room during surgical procedures affects team performance, reflects individual skills, and is related to the complexity of the operation process. During the procedural training of surgeons (residents), feedback and guidance is given through verbal communication. A classification method based on structural analysis of the contents was developed to analyze verbal communication. This study aimed to evaluate whether a classification method for the contents of verbal communication in the operating room could provide insight into the teaching processes. Eight laparoscopic cholecystectomies were videotaped. Two entire cholecystectomies and the dissection phase of six additional procedures were analyzed by categorization of the communication in terms of type (4 categories: commanding, explaining, questioning, and miscellaneous) and content (9 categories: operation method, location, direction, instrument handling, visualization, anatomy and pathology, general, private, undefinable). The operation was divided into six phases: start, dissection, clipping, separating, control, closing. Classification of the communication during two entire procedures showed that each phase of the operation was dominated by different kinds of communication. A high percentage of explaining anatomy and pathology was found throughout the whole procedure except for the control and closing phases. In the dissection phases, 60% of verbal communication concerned explaining. These explaining communication events were divided as follows: 27% operation method, 19% anatomy and pathology, 25% location (positioning of the instrument-tissue interaction), 15% direction (direction of tissue manipulation), 11% instrument handling, and 3% other nonclassified instructions. The proposed classification method is feasible for analyzing verbal communication during surgical procedures. Communication content objectively reflects the interaction between surgeon and resident. This information can potentially be used to specify training needs, and may contribute to the evaluation of different training methods.

Control by quality: proposition of a typology.

PubMed

Pujo, P; Pillet, M

The application of Quality tools and methods in industrial management has always had a fundamental impact on the control of production. It influences the behavior of the actors concerned, while introducing the necessary notions and formalizations, especially for production systems with little or no automation, which constitute a large part of the industrial activity. Several quality approaches are applied in the workshop and are implemented at the level of the control. In this paper, the authors present a typology of the various approaches that have successively influenced control, such as statistical process control, quality assurance, and continuous improvement. First the authors present a parallel between production control and quality organizational structure. They note the duality between control, which is aimed at increasing productivity, and quality, which aims to satisfy the needs of the customer. They also note the hierarchical organizational structure of these two systems of management with, at each level, the notion of a feedback loop. This notion is fundamental to any kind of decision making. The paper is organized around the operational, tactical, and strategic levels, by describing for each level the main methods and tools for control by quality. The overview of these tools and methods starts at the operational level, with the Statistical Process Control, the Taguchi technique, and the "six sigma" approach. On the tactical level, we find a quality system approach, with a documented description of the procedures introduced in the firm. The management system can refer here to Quality Assurance, Total Productive Maintenance, or Management by Total Quality. The formalization through procedures of the rules of decision governing the process control enhances the validity of these rules. This leads to the enhancement of their reliability and to their consolidation. All this counterbalances the human, intrinsically fluctuating, behavior of the control operators. Strategic control by quality is then detailed, and the two main approaches, the continuous improvement approach and the proactive improvement approach, are introduced. Finally, the authors observe that at each of the three levels, the continuous process improvement, which is a component of Total Quality, becomes an essential preoccupation for the control. Ultimately, the recursive utilization of the Deming cycle remains the best practice for the control by quality.

Dynamic engagement of cognitive control modulates recovery from misinterpretation during real-time language processing

PubMed Central

Hsu, Nina S.; Novick, Jared M.

2016-01-01

Speech unfolds swiftly, yet listeners keep pace by rapidly assigning meaning to what they hear. Sometimes though, initial interpretations turn out wrong. How do listeners revise misinterpretations of language input moment-by-moment, to avoid comprehension errors? Cognitive control may play a role by detecting when processing has gone awry, and then initiating behavioral adjustments accordingly. However, no research has investigated a cause-and-effect interplay between cognitive control engagement and overriding erroneous interpretations in real-time. Using a novel cross-task paradigm, we show that Stroop-conflict detection, which mobilizes cognitive control procedures, subsequently facilitates listeners’ incremental processing of temporarily ambiguous spoken instructions that induce brief misinterpretation. When instructions followed Stroop-incongruent versus-congruent items, listeners’ eye-movements to objects in a scene reflected more transient consideration of the false interpretation and earlier recovery of the correct one. Comprehension errors also decreased. Cognitive control engagement therefore accelerates sentence re-interpretation processes, even as linguistic input is still unfolding. PMID:26957521

Contamination Control in Hybrid Microelectronic Modules. Part 1: Identification of Critical Process and Contaminants

NASA Technical Reports Server (NTRS)

Himmel, R. P.

1975-01-01

Various hybrid processing steps, handling procedures, and materials are examined in an attempt to identify sources of contamination and to propose methods for the control of these contaminants. It is found that package sealing, assembly, and rework are especially susceptible to contamination. Moisture and loose particles are identified as the worst contaminants. The points at which contaminants are most likely to enter the hybrid package are also identified, and both general and specific methods for their detection and control are developed. In general, the most effective controls for contaminants are: clean working areas, visual inspection at each step of the process, and effective cleaning at critical process steps. Specific methods suggested include the detection of loose particles by a precap visual inspection, by preseal and post-seal electrical testing, and by a particle impact noise test. Moisture is best controlled by sealing all packages in a clean, dry, inert atmosphere after a thorough bake-out of all parts.

Qualification Procedures for VHSIC/VLSI

DTIC Science & Technology

1990-12-01

alternative approach for qualification of complex microcircuits. To address the technical issues related to a process oriented qualification approach, the...methodology of microcircuit process control to promote the United States to a position of supplying the nighest quality and most reliable...available resources . o Coordinate document reviews with weekly and monthly status reviews on progress. o Summarize results and collate into four basic

Soft plasma processing of organic nanowires: a route for the fabrication of 1D organic heterostructures and the template synthesis of inorganic 1D nanostructures.

PubMed

Alcaire, Maria; Sanchez-Valencia, Juan R; Aparicio, Francisco J; Saghi, Zineb; Gonzalez-Gonzalez, Juan C; Barranco, Angel; Zian, Youssef Oulad; Gonzalez-Elipe, Agustin R; Midgley, Paul; Espinos, Juan P; Groening, Pierangelo; Borras, Ana

2011-11-01

Hierarchical (branched) and hybrid metal-NPs/organic supported NWs are fabricated through controlled plasma processing of metalloporphyrin, metallophthalocyanine and perylene nanowires. The procedure is also applied for the development of a general template route for the synthesis of supported metal and metal oxide nanowires.

Using statistical process control to make data-based clinical decisions.

PubMed

Pfadt, A; Wheeler, D J

1995-01-01

Applied behavior analysis is based on an investigation of variability due to interrelationships among antecedents, behavior, and consequences. This permits testable hypotheses about the causes of behavior as well as for the course of treatment to be evaluated empirically. Such information provides corrective feedback for making data-based clinical decisions. This paper considers how a different approach to the analysis of variability based on the writings of Walter Shewart and W. Edwards Deming in the area of industrial quality control helps to achieve similar objectives. Statistical process control (SPC) was developed to implement a process of continual product improvement while achieving compliance with production standards and other requirements for promoting customer satisfaction. SPC involves the use of simple statistical tools, such as histograms and control charts, as well as problem-solving techniques, such as flow charts, cause-and-effect diagrams, and Pareto charts, to implement Deming's management philosophy. These data-analytic procedures can be incorporated into a human service organization to help to achieve its stated objectives in a manner that leads to continuous improvement in the functioning of the clients who are its customers. Examples are provided to illustrate how SPC procedures can be used to analyze behavioral data. Issues related to the application of these tools for making data-based clinical decisions and for creating an organizational climate that promotes their routine use in applied settings are also considered.

Biofilms of Enterococcus faecalis and Enterococcus faecium isolated from the processing of ricotta and the control of these pathogens through cleaning and sanitization procedures.

PubMed

da Silva Fernandes, Meg; Kabuki, Dirce Yorika; Kuaye, Arnaldo Yoshiteru

2015-05-04

The biofilm formation of Enterococcus faecalis and Enterococcus faecium isolated from the processing of ricotta on stainless steel coupons was evaluated, and the effect of cleaning and sanitization procedures in the control of these biofilms was determined. The formation of biofilms was observed while varying the incubation temperature (7, 25 and 39°C) and time (0, 1, 2, 4, 6 and 8 days). At 7°C, the counts of E. faecalis and E. faecium were below 2 log10 CFU/cm(2). For the temperatures of 25 and 39°C, after 1 day, the counts of E. faecalis and E. faecium were 5.75 and 6.07 log10 CFU/cm(2), respectively, which is characteristic of biofilm formation. The tested sanitation procedures a) acid-anionic tensioactive cleaning, b) anionic tensioactive cleaning+sanitizer and c) acid-anionic tensioactive cleaning+sanitizer were effective in removing the biofilms, reducing the counts to levels below 0.4 log10 CFU/cm(2). The sanitizer biguanide was the least effective, and peracetic acid was the most effective. These studies revealed the ability of enterococci to form biofilms and the importance of the cleaning step and the type of sanitizer used in sanitation processes for the effective removal of biofilms. Copyright © 2015 Elsevier B.V. All rights reserved.

NASA/RAE collaboration on nonlinear control using the F-8C digital fly-by-wire aircraft

NASA Technical Reports Server (NTRS)

Butler, G. F.; Corbin, M. J.; Mepham, S.; Stewart, J. F.; Larson, R. R.

1983-01-01

Design procedures are reviewed for variable integral control to optimize response (VICTOR) algorithms and results of preliminary flight tests are presented. The F-8C aircraft is operated in the remotely augmented vehicle (RAV) mode, with the control laws implemented as FORTRAN programs on a ground-based computer. Pilot commands and sensor information are telemetered to the ground, where the data are processed to form surface commands which are then telemetered back to the aircraft. The RAV mode represents a singlestring (simplex) system and is therefore vulnerable to a hardover since comparison monitoring is not possible. Hence, extensive error checking is conducted on both the ground and airborne computers to prevent the development of potentially hazardous situations. Experience with the RAV monitoring and validation procedures is described.

Laser vaporization in treatment of superficial endometriosis of the uterine cervix

NASA Astrophysics Data System (ADS)

Wozniak, Jakub; Wilczak, Maciej; Opala, Tomasz; Pisarska-Krawczyk, Magdalena; Cwojdzinski, Marek; Pisarski, Tadeusz

1996-03-01

The study shows the treatment of superficial endometriosis of the uterine cervix in 79 patients. After first vaporization 74 patients were cured successfully. In two cases the laser procedure should be repeated and in 3 women the operation should be performed for the third time. All patients are still under control in our department and there is no recurrence observed. Carbon- dioxide laser vaporization under colposcopic control is an efficient method of treatment of superficial endometriosis of the uterine cervix that requires no anaesthesia. The healing process after laser procedures is fast and without complications. The number of recurrences is low. Use of carbon-dioxide laser under colposcopic control because of precise destruction of lesions, fast healing and a low number of recurrences seems to be the method of choice.

Treatment of the control mechanisms of light airplanes in the flutter clearance process

NASA Technical Reports Server (NTRS)

Breitbach, E. J.

1979-01-01

It has become more and more evident that many difficulties encountered in the course of aircraft flutter analyses can be traced to strong localized nonlinearities in the control mechanisms. To cope with these problems, more reliable mathematical models paying special attention to control system nonlinearities were established by means of modified ground vibration test procedures in combination with suitably adapted modal synthesis approaches. Three different concepts are presented.

Design of experiments enhanced statistical process control for wind tunnel check standard testing

NASA Astrophysics Data System (ADS)

Phillips, Ben D.

The current wind tunnel check standard testing program at NASA Langley Research Center is focused on increasing data quality, uncertainty quantification and overall control and improvement of wind tunnel measurement processes. The statistical process control (SPC) methodology employed in the check standard testing program allows for the tracking of variations in measurements over time as well as an overall assessment of facility health. While the SPC approach can and does provide researchers with valuable information, it has certain limitations in the areas of process improvement and uncertainty quantification. It is thought by utilizing design of experiments methodology in conjunction with the current SPC practices that one can efficiently and more robustly characterize uncertainties and develop enhanced process improvement procedures. In this research, methodologies were developed to generate regression models for wind tunnel calibration coefficients, balance force coefficients and wind tunnel flow angularities. The coefficients of these regression models were then tracked in statistical process control charts, giving a higher level of understanding of the processes. The methodology outlined is sufficiently generic such that this research can be applicable to any wind tunnel check standard testing program.

Positive electrode processing for Hughes NiH2 cells

NASA Technical Reports Server (NTRS)

Bleser, C. A.

1982-01-01

The basic procedures were developed for the manufacture of nickel cadmium batteries. An electrochemical impregnation in an aqueous ethanol solution is used in this process. Several additional controls were instituted for production of flight electrodes, including a Hughes controlled MCD, a solution reserved exclusively for the impregnation of Hughes positive electrodes a system of complete traceability for individual electrodes, an electrical characterization test to provide information on weight and capacity at the plaque level, and a stress test to provide data on capacity, weight, and physical parameters at the electrode level.

Manual for the GAW Precipitation Chemistry Programme: Guidelines, Data Quality Objectives and Standard Operating Procedures

DTIC Science & Technology

2004-11-01

J . Geophys. Res. 101, 6883-6897. Galloway, J . N., Keene, W. C., Artz, R. S., Church, T . M. and Knap, A. H. (1989) Processes controlling the...remote areas of the world. J . Geophys. Res. 88(C9), 5122-5130. Keene, W. C., Montag, J . A., Maben, J . R., Southwell, M., Leonard, J ., Church, T . M...6883-6897. Galloway, J . N., Keene, W. C., Artz, R. S., Church, T . M. and Knap, A. H. (1989) Processes controlling the concentrations of SO42-, NO3

New type of measuring and intelligent instrument for curing tobacco

NASA Astrophysics Data System (ADS)

Yi, Chui-Jie; Huang, Xieqing; Chen, Tianning; Xia, Hong

1993-09-01

A new type of measuring intelligent instrument for cured tobacco is presented in this paper. Based on fuzzy linguistic control principles the instrument is used to controlling the temperature and humidity during cured tobacco taking 803 1 singlechip computer as a center controller. By using methods of fuzzy weighted factors the cross coupling in curing procedures is decoupled. Results that the instrument has producted indicate the fuzzy controller in the instrument has perfect performance for process of cured tobacco as shown in figure

Interfacing LabVIEW With Instrumentation for Electronic Failure Analysis and Beyond

NASA Technical Reports Server (NTRS)

Buchanan, Randy K.; Bryan, Coleman; Ludwig, Larry

1996-01-01

The Laboratory Virtual Instrumentation Engineering Workstation (LabVIEW) software is designed such that equipment and processes related to control systems can be operationally lined and controlled by the use of a computer. Various processes within the failure analysis laboratories of NASA's Kennedy Space Center (KSC) demonstrate the need for modernization and, in some cases, automation, using LabVIEW. An examination of procedures and practices with the Failure Analaysis Laboratory resulted in the conclusion that some device was necessary to elevate the potential users of LabVIEW to an operational level in minimum time. This paper outlines the process involved in creating a tutorial application to enable personnel to apply LabVIEW to their specific projects. Suggestions for furthering the extent to which LabVIEW is used are provided in the areas of data acquisition and process control.

An update on methods for cryopreservation and thawing of hemopoietic stem cells.

PubMed

Lecchi, Lucilla; Giovanelli, Silvia; Gagliardi, Barbara; Pezzali, Ilaria; Ratti, Ilaria; Marconi, Maurizio

2016-06-01

The aim of this article is to review a number of variables that may affect the cryopreservation of minimally manipulated products containing allogeneic or autologous hemopoietic progenitor cells (HPC) used for transplantation, with particular reference to processing, type and addition of cryoprotectant, cell concentration, volume, freezing procedure, cooling rate, storage, thawing, and quality management. After defining final product's requirements in compliance with norms, laws and regulations, it is crucial to define the critical control points of the process. New approaches of processing were developed in the last few years such as automatic devices for volume reduction and high cell concentration in the frozen product. DMSO at 10% final concentration is still the most used cryoprotectant for HPC cryopreservation. Although controlled rate freezing is the recommended method for HPC cryopreservation, alternative methods may be used. Last generation vapor storage vessels ensure temperature stability better than older tanks. Their use may reduce risks of cross-contamination. Finally we review advantages and disadvantages of thawing procedures that may be carried out in the laboratory or at the patient's bedside. Copyright © 2016 Elsevier Ltd. All rights reserved.

Analytical control test plan and microbiological methods for the water recovery test

NASA Technical Reports Server (NTRS)

Traweek, M. S. (Editor); Tatara, J. D. (Editor)

1994-01-01

Qualitative and quantitative laboratory results are important to the decision-making process. In some cases, they may represent the only basis for deciding between two or more given options or processes. Therefore, it is essential that handling of laboratory samples and analytical operations employed are performed at a deliberate level of conscientious effort. Reporting erroneous results can lead to faulty interpretations and result in misinformed decisions. This document provides analytical control specifications which will govern future test procedures related to all Water Recovery Test (WRT) Phase 3 activities to be conducted at the National Aeronautics and Space Administration/Marshall Space Flight Center (NASA/MSFC). This document addresses the process which will be used to verify analytical data generated throughout the test period, and to identify responsibilities of key personnel and participating laboratories, the chains of communication to be followed, and ensure that approved methodology and procedures are used during WRT activities. This document does not outline specifics, but provides a minimum guideline by which sampling protocols, analysis methodologies, test site operations, and laboratory operations should be developed.

Practical experimental certification of computational quantum gates using a twirling procedure.

PubMed

Moussa, Osama; da Silva, Marcus P; Ryan, Colm A; Laflamme, Raymond

2012-08-17

Because of the technical difficulty of building large quantum computers, it is important to be able to estimate how faithful a given implementation is to an ideal quantum computer. The common approach of completely characterizing the computation process via quantum process tomography requires an exponential amount of resources, and thus is not practical even for relatively small devices. We solve this problem by demonstrating that twirling experiments previously used to characterize the average fidelity of quantum memories efficiently can be easily adapted to estimate the average fidelity of the experimental implementation of important quantum computation processes, such as unitaries in the Clifford group, in a practical and efficient manner with applicability in current quantum devices. Using this procedure, we demonstrate state-of-the-art coherent control of an ensemble of magnetic moments of nuclear spins in a single crystal solid by implementing the encoding operation for a 3-qubit code with only a 1% degradation in average fidelity discounting preparation and measurement errors. We also highlight one of the advances that was instrumental in achieving such high fidelity control.

Review of indicators for cross-sectoral optimization of nosocomial infection prophylaxis – a perspective from structurally- and process-oriented hygiene

PubMed Central

Hübner, Nils-Olaf; Fleßa, Steffen; Jakisch, Ralf; Assadian, Ojan; Kramer, Axel

2012-01-01

In the care of patients, the prevention of nosocomial infections is crucial. For it to be successful, cross-sectoral, interface-oriented hygiene quality management is necessary. The goal is to apply the HACCP (Hazard Assessment and Critical Control Points) concept to hospital hygiene, in order to create a multi-dimensional hygiene control system based on hygiene indicators that will overcome the limitations of a procedurally non-integrated and non-cross-sectoral view of hygiene. Three critical risk dimensions can be identified for the implementation of three-dimensional quality control of hygiene in clinical routine: the constitution of the person concerned, the surrounding physical structures and technical equipment, and the medical procedures. In these dimensions, the establishment of indicators and threshold values enables a comprehensive assessment of hygiene quality. Thus, the cross-sectoral evaluation of the quality of structure, processes and results is decisive for the success of integrated infection prophylaxis. This study lays the foundation for hygiene indicator requirements and develops initial concepts for evaluating quality management in hygiene. PMID:22558049

Real-time dynamics and control strategies for space operations of flexible structures

NASA Technical Reports Server (NTRS)

Park, K. C.; Alvin, K. F.; Alexander, S.

1993-01-01

This project (NAG9-574) was meant to be a three-year research project. However, due to NASA's reorganizations during 1992, the project was funded only for one year. Accordingly, every effort was made to make the present final report as if the project was meant to be for one-year duration. Originally, during the first year we were planning to accomplish the following: we were to start with a three dimensional flexible manipulator beam with articulated joints and with a linear control-based controller applied at the joints; using this simple example, we were to design the software systems requirements for real-time processing, introduce the streamlining of various computational algorithms, perform the necessary reorganization of the partitioned simulation procedures, and assess the potential speed-up realization of the solution process by parallel computations. The three reports included as part of the final report address: the streamlining of various computational algorithms; the necessary reorganization of the partitioned simulation procedures, in particular the observer models; and an initial attempt of reconfiguring the flexible space structures.

Computation of records of streamflow at control structures

USGS Publications Warehouse

Collins, Dannie L.

1977-01-01

Traditional methods of computing streamflow records on large, low-gradient streams require a continuous record of water-surface slope over a natural channel reach. This slope must be of sufficient magnitude to be accuratly measured with available stage measuring devices. On highly regulated streams, this slope approaches zero during periods of low flow and accurate measurement is difficult. Methods are described to calibrate multipurpose regulating control structures to more accurately compute streamflow records on highly-regulated streams. Hydraulic theory, assuming steady, uniform flow during a computational interval, is described for five different types of flow control. The controls are: Tainter gates, hydraulic turbines, fixed spillways, navigation locks, and crest gates. Detailed calibration procedures are described for the five different controls as well as for several flow regimes for some of the controls. The instrumentation package and computer programs necessary to collect and process the field data are discussed. Two typical calibration procedures and measurement data are presented to illustrate the accuracy of the methods. (Woodard-USGS)

A Cyclic Voltammetry Experiment for the Instrumental Analysis Laboratory.

ERIC Educational Resources Information Center

Baldwin, Richard P.; And Others

1984-01-01

Background information and procedures are provided for experiments that illustrate the nature of cyclic voltammetry and its application in the characterization of organic electrode processes. The experiments also demonstrate the concepts of electrochemical reversibility and diffusion-controlled mass transfer. (JN)

40 CFR 725.70 - Compliance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Compliance. 725.70 Section 725.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Administrative Procedures § 725.70 Compliance. (a) Failure...

40 CFR 725.70 - Compliance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Compliance. 725.70 Section 725.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Administrative Procedures § 725.70 Compliance. (a) Failure...

QFD emphasis of IME design

NASA Astrophysics Data System (ADS)

Erickson, C. M.; Martinez, A.

1993-06-01

The 1992 Integrated Modular Engine (IME) design concept, proposed to the Air Force Space Systems Division as a candidate for a National Launch System (NLS) upper stage, emphasized a detailed Quality Functional Deployment (QFD) procedure which set the basis for its final selection. With a list of engine requirements defined and prioritized by the customer, a QFD procedure was implemented where the characteristics of a number of engine and component configurations were assessed for degree of requirement satisfaction. The QFD process emphasized operability, cost, reliability and performance, with relative importance specified by the customer. Existing technology and near-term advanced technology were surveyed to achieve the required design strategies. In the process, advanced nozzles, advanced turbomachinery, valves, controls, and operational procedures were evaluated. The integrated arrangement of three conventional bell nozzle thrust chambers with two advanced turbopump sets selected as the configuration meeting all requirements was rated significantly ahead of the other candidates, including the Aerospike and horizontal flow nozzle configurations.

PLA realizations for VLSI state machines

NASA Technical Reports Server (NTRS)

Gopalakrishnan, S.; Whitaker, S.; Maki, G.; Liu, K.

1990-01-01

A major problem associated with state assignment procedures for VLSI controllers is obtaining an assignment that produces minimal or near minimal logic. The key item in Programmable Logic Array (PLA) area minimization is the number of unique product terms required by the design equations. This paper presents a state assignment algorithm for minimizing the number of product terms required to implement a finite state machine using a PLA. Partition algebra with predecessor state information is used to derive a near optimal state assignment. A maximum bound on the number of product terms required can be obtained by inspecting the predecessor state information. The state assignment algorithm presented is much simpler than existing procedures and leads to the same number of product terms or less. An area-efficient PLA structure implemented in a 1.0 micron CMOS process is presented along with a summary of the performance for a controller implemented using this design procedure.

Development of autonomous controller system of high speed UAV from simulation to ready to fly condition

NASA Astrophysics Data System (ADS)

Yudhi Irwanto, Herma

2018-02-01

The development of autonomous controller system that is specially used in our high speed UAV, it’s call RKX-200EDF/TJ controlled vehicle needs to be continued as a step to mastery and to developt control system of LAPAN’s satellite launching rocket. The weakness of the existing control system in this high speed UAV needs to be repaired and replaced using the autonomous controller system. Conversion steps for ready-to-fly system involved controlling X tail fin, adjusting auto take off procedure by adding X axis sensor, procedure of way points reading and process of measuring distance and heading to the nearest way point, developing user-friendly ground station, and adding tools for safety landing. The development of this autonomous controller system also covered a real flying test in Pandanwangi, Lumajang in November 2016. Unfortunately, the flying test was not successful because the booster rocket was blown right after burning. However, the system could record the event and demonstrated that the controller system had worked according to plan.

PLAN-TA9-2443(U), Rev. B Remediated Nitrate Salt (RNS) Surrogate Formulation and Testing Standard Procedure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Geoffrey Wayne

2016-03-16

This document identifies scope and some general procedural steps for performing Remediated Nitrate Salt (RNS) Surrogate Formulation and Testing. This Test Plan describes the requirements, responsibilities, and process for preparing and testing a range of chemical surrogates intended to mimic the energetic response of waste created during processing of legacy nitrate salts. The surrogates developed are expected to bound1 the thermal and mechanical sensitivity of such waste, allowing for the development of process parameters required to minimize the risk to worker and public when processing this waste. Such parameters will be based on the worst-case kinetic parameters as derived frommore » APTAC measurements as well as the development of controls to mitigate sensitivities that may exist due to friction, impact, and spark. This Test Plan will define the scope and technical approach for activities that implement Quality Assurance requirements relevant to formulation and testing.« less

Residual Gases in Crystal Growth Systems: Their Origin, Magnitude, and Dependence on the Processing Conditions

NASA Technical Reports Server (NTRS)

Palosz, W.

2003-01-01

Residual gases present in closed ampoules may affect different crystal growth processes. Their presence may affect techniques requiring low pressures and affect the crystal quality in different ways. For that reason a good understanding and control of formation of residual gases may be important for an optimum design and meaningful interpretation of crystal growth experiments. Our extensive experimental and theoretical study includes degassing of silica glass and generation of gases from various source materials. Different materials processing conditions, like outgassing under vacuum, annealing in hydrogen, resublimation, different material preparation procedures, multiple annealings, different processing times, and others were applied and their effect on the amount and composition of gas were analyzed. The experimental results were interpreted based on theoretical calculations on diffusion in silica glass and source materials and thermochemistry of the system. Procedures for a reduction of the amount of gas are also discussed.

Fault detection in heavy duty wheels by advanced vibration processing techniques and lumped parameter modeling

NASA Astrophysics Data System (ADS)

Malago`, M.; Mucchi, E.; Dalpiaz, G.

2016-03-01

Heavy duty wheels are used in applications such as automatic vehicles and are mainly composed of a polyurethane tread glued to a cast iron hub. In the manufacturing process, the adhesive application between tread and hub is a critical assembly phase, since it is completely made by an operator and a contamination of the bond area may happen. Furthermore, the presence of rust on the hub surface can contribute to worsen the adherence interface, reducing the operating life. In this scenario, a quality control procedure for fault detection to be used at the end of the manufacturing process has been developed. This procedure is based on vibration processing techniques and takes advantages of the results of a lumped parameter model. Indicators based on cyclostationarity can be considered as key parameters to be adopted in a monitoring test station at the end of the production line due to their not deterministic characteristics.

Smith predictor based-sliding mode controller for integrating processes with elevated deadtime.

PubMed

Camacho, Oscar; De la Cruz, Francisco

2004-04-01

An approach to control integrating processes with elevated deadtime using a Smith predictor sliding mode controller is presented. A PID sliding surface and an integrating first-order plus deadtime model have been used to synthesize the controller. Since the performance of existing controllers with a Smith predictor decrease in the presence of modeling errors, this paper presents a simple approach to combining the Smith predictor with the sliding mode concept, which is a proven, simple, and robust procedure. The proposed scheme has a set of tuning equations as a function of the characteristic parameters of the model. For implementation of our proposed approach, computer based industrial controllers that execute PID algorithms can be used. The performance and robustness of the proposed controller are compared with the Matausek-Micić scheme for linear systems using simulations.

Virtualized MME Design for IoT Support in 5G Systems.

PubMed

Andres-Maldonado, Pilar; Ameigeiras, Pablo; Prados-Garzon, Jonathan; Ramos-Munoz, Juan Jose; Lopez-Soler, Juan Manuel

2016-08-22

Cellular systems are recently being considered an option to provide support to the Internet of Things (IoT). To enable this support, the 3rd Generation Partnership Project (3GPP) has introduced new procedures specifically targeted for cellular IoT. With one of these procedures, the transmissions of small and infrequent data packets from/to the devices are encapsulated in signaling messages and sent through the control plane. However, these transmissions from/to a massive number of devices may imply a major increase of the processing load on the control plane entities of the network and in particular on the Mobility Management Entity (MME). In this paper, we propose two designs of an MME based on Network Function Virtualization (NFV) that aim at facilitating the IoT support. The first proposed design partially separates the processing resources dedicated to each traffic class. The second design includes traffic shaping to control the traffic of each class. We consider three classes: Mobile Broadband (MBB), low latency Machine to Machine communications (lM2M) and delay-tolerant M2M communications. Our proposals enable reducing the processing resources and, therefore, the cost. Additionally, results show that the proposed designs lessen the impact between classes, so they ease the compliance of the delay requirements of MBB and lM2M communications.

Computations on Wings With Full-Span Oscillating Control Surfaces Using Navier-Stokes Equations

NASA Technical Reports Server (NTRS)

Guruswamy, Guru P.

2013-01-01

A dual-level parallel procedure is presented for computing large databases to support aerospace vehicle design. This procedure has been developed as a single Unix script within the Parallel Batch Submission environment utilizing MPIexec and runs MPI based analysis software. It has been developed to provide a process for aerospace designers to generate data for large numbers of cases with the highest possible fidelity and reasonable wall clock time. A single job submission environment has been created to avoid keeping track of multiple jobs and the associated system administration overhead. The process has been demonstrated for computing large databases for the design of typical aerospace configurations, a launch vehicle and a rotorcraft.

Common method biases in behavioral research: a critical review of the literature and recommended remedies.

PubMed

Podsakoff, Philip M; MacKenzie, Scott B; Lee, Jeong-Yeon; Podsakoff, Nathan P

2003-10-01

Interest in the problem of method biases has a long history in the behavioral sciences. Despite this, a comprehensive summary of the potential sources of method biases and how to control for them does not exist. Therefore, the purpose of this article is to examine the extent to which method biases influence behavioral research results, identify potential sources of method biases, discuss the cognitive processes through which method biases influence responses to measures, evaluate the many different procedural and statistical techniques that can be used to control method biases, and provide recommendations for how to select appropriate procedural and statistical remedies for different types of research settings.

Subgrid-scale scalar flux modelling based on optimal estimation theory and machine-learning procedures

NASA Astrophysics Data System (ADS)

Vollant, A.; Balarac, G.; Corre, C.

2017-09-01

New procedures are explored for the development of models in the context of large eddy simulation (LES) of a passive scalar. They rely on the combination of the optimal estimator theory with machine-learning algorithms. The concept of optimal estimator allows to identify the most accurate set of parameters to be used when deriving a model. The model itself can then be defined by training an artificial neural network (ANN) on a database derived from the filtering of direct numerical simulation (DNS) results. This procedure leads to a subgrid scale model displaying good structural performance, which allows to perform LESs very close to the filtered DNS results. However, this first procedure does not control the functional performance so that the model can fail when the flow configuration differs from the training database. Another procedure is then proposed, where the model functional form is imposed and the ANN used only to define the model coefficients. The training step is a bi-objective optimisation in order to control both structural and functional performances. The model derived from this second procedure proves to be more robust. It also provides stable LESs for a turbulent plane jet flow configuration very far from the training database but over-estimates the mixing process in that case.

Adaptive identification and control of structural dynamics systems using recursive lattice filters

NASA Technical Reports Server (NTRS)

Sundararajan, N.; Montgomery, R. C.; Williams, J. P.

1985-01-01

A new approach for adaptive identification and control of structural dynamic systems by using least squares lattice filters thar are widely used in the signal processing area is presented. Testing procedures for interfacing the lattice filter identification methods and modal control method for stable closed loop adaptive control are presented. The methods are illustrated for a free-free beam and for a complex flexible grid, with the basic control objective being vibration suppression. The approach is validated by using both simulations and experimental facilities available at the Langley Research Center.

Functional neuroanatomy of visual masking deficits in schizophrenia.

PubMed

Green, Michael F; Lee, Junghee; Cohen, Mark S; Engel, Steven A; Korb, Alexander S; Nuechterlein, Keith H; Wynn, Jonathan K; Glahn, David C

2009-12-01

Visual masking procedures assess the earliest stages of visual processing. Patients with schizophrenia reliably show deficits on visual masking, and these procedures have been used to explore vulnerability to schizophrenia, probe underlying neural circuits, and help explain functional outcome. To identify and compare regional brain activity associated with one form of visual masking (ie, backward masking) in schizophrenic patients and healthy controls. Subjects received functional magnetic resonance imaging scans. While in the scanner, subjects performed a backward masking task and were given 3 functional localizer activation scans to identify early visual processing regions of interest (ROIs). University of California, Los Angeles, and the Department of Veterans Affairs Greater Los Angeles Healthcare System. Nineteen patients with schizophrenia and 19 healthy control subjects. Main Outcome Measure The magnitude of the functional magnetic resonance imaging signal during backward masking. Two ROIs (lateral occipital complex [LO] and the human motion selective cortex [hMT+]) showed sensitivity to the effects of masking, meaning that signal in these areas increased as the target became more visible. Patients had lower activation than controls in LO across all levels of visibility but did not differ in other visual processing ROIs. Using whole-brain analyses, we also identified areas outside the ROIs that were sensitive to masking effects (including bilateral inferior parietal lobe and thalamus), but groups did not differ in signal magnitude in these areas. The study results support a key role in LO for visual masking, consistent with previous studies in healthy controls. The current results indicate that patients fail to activate LO to the same extent as controls during visual processing regardless of stimulus visibility, suggesting a neural basis for the visual masking deficit, and possibly other visual integration deficits, in schizophrenia.

International Heart Valve Bank Survey: A Review of Processing Practices and Activity Outcomes

PubMed Central

Albrecht, Helmi; Lim, Yeong Phang; Manning, Linda

2013-01-01

A survey of 24 international heart valve banks was conducted to acquire information on heart valve processing techniques used and outcomes achieved. The objective was to provide an overview of heart valve banking activities for tissue bankers, tissue banking associations, and regulatory bodies worldwide. Despite similarities found for basic manufacturing processes, distinct differences in procedural details were also identified. The similarities included (1) use of sterile culture media for procedures, (2) antibiotic decontamination, (3) use of dimethyl sulfoxide (DMSO) as a cryoprotectant, (4) controlled rate freezing for cryopreservation, and (5) storage at ultralow temperatures of below −135°C. Differences in procedures included (1) type of sterile media used, (2) antibiotics combination, (3) temperature and duration used for bioburden reduction, (4) concentration of DMSO used for cryopreservation, and (5) storage duration for released allografts. For most banks, the primary reasons why allografts failed to meet release criteria were positive microbiological culture and abnormal morphology. On average, 85% of allografts meeting release criteria were implanted, with valve size and type being the main reasons why released allografts were not used clinically. The wide variation in percentage of allografts meeting release requirements, despite undergoing validated manufacturing procedures, justifies the need for regular review of important outcomes as cited in this paper, in order to encourage comparison and improvements in the HVBs' processes. PMID:24163756

Social incentives improve deliberative but not procedural learning in older adults.

PubMed

Gorlick, Marissa A; Maddox, W Todd

2015-01-01

Age-related deficits are seen across tasks where learning depends on asocial feedback processing, however plasticity has been observed in some of the same tasks in social contexts suggesting a novel way to attenuate deficits. Socioemotional selectivity theory suggests this plasticity is due to a deliberative motivational shift toward achieving well-being with age (positivity effect) that reverses when executive processes are limited (negativity effect). The present study examined the interaction of feedback valence (positive, negative) and social salience (emotional face feedback - happy; angry, asocial point feedback - gain; loss) on learning in a deliberative task that challenges executive processes and a procedural task that does not. We predict that angry face feedback will improve learning in a deliberative task when executive function is challenged. We tested two competing hypotheses regarding the interactive effects of deliberative emotional biases on automatic feedback processing: (1) If deliberative emotion regulation and automatic feedback are interactive we expect happy face feedback to improve learning and angry face feedback to impair learning in older adults because cognitive control is available. (2) If deliberative emotion regulation and automatic feedback are not interactive we predict that emotional face feedback will not improve procedural learning regardless of valence. Results demonstrate that older adults show persistent deficits relative to younger adults during procedural category learning suggesting that deliberative emotional biases do not interact with automatic feedback processing. Interestingly, a subgroup of older adults identified as potentially using deliberative strategies tended to learn as well as younger adults with angry relative to happy feedback, matching the pattern observed in the deliberative task. Results suggest that deliberative emotional biases can improve deliberative learning, but have no effect on procedural learning.

Contributions of spectral frequency analyses to the study of P50 ERP amplitude and suppression in bipolar disorder with or without a history of psychosis.

PubMed

Carroll, Christine A; Kieffaber, Paul D; Vohs, Jenifer L; O'Donnell, Brian F; Shekhar, Anantha; Hetrick, William P

2008-11-01

The present study investigated event-related brain potential (ERP) indices of auditory processing and sensory gating in bipolar disorder and subgroups of bipolar patients with or without a history of psychosis using the P50 dual-click procedure. Auditory-evoked activity in two discrete frequency bands also was explored to distinguish between sensory registration and selective attention deficits. Thirty-one individuals with bipolar disorder and 28 non-psychiatric controls were compared on ERP indices of auditory processing using a dual-click procedure. In addition to conventional P50 ERP peak-picking techniques, quantitative frequency analyses were applied to the ERP data to isolate stages of information processing associated with sensory registration (20-50 Hz; gamma band) and selective attention (0-20 Hz; low-frequency band). Compared to the non-psychiatric control group, patients with bipolar disorder exhibited reduced S1 response magnitudes for the conventional P50 peak-picking and low-frequency response analyses. A bipolar subgroup effect suggested that the attenuated S1 magnitudes from the P50 peak-picking and low-frequency analyses were largely attributable to patients without a history of psychosis. The analysis of distinct frequency bands of the auditory-evoked response elicited during the dual-click procedure allowed further specification of the nature of auditory sensory processing and gating deficits in bipolar disorder with or without a history of psychosis. The observed S1 effects in the low-frequency band suggest selective attention deficits in bipolar patients, especially those patients without a history of psychosis, which may reflect a diminished capacity to selectively attend to salient stimuli as opposed to impairments of inhibitory sensory processes.

Profile negotiation: An air/ground automation integration concept for managing arrival traffic

NASA Technical Reports Server (NTRS)

Williams, David H.; Arbuckle, P. Douglas; Green, Steven M.; Denbraven, Wim

1993-01-01

NASA Ames Research Center and NASA Langley Research Center conducted a joint simulation study to evaluate a profile negotiation process (PNP) between a time-based air traffic control ATC system and an airplane equipped with a four dimensional flight management system (4D FMS). Prototype procedures were developed to support the functional implementation of this process. The PNP was designed to provide an arrival trajectory solution that satisfies the separation requirements of ATC while remaining as close as possible to the airplane's preferred trajectory. The Transport Systems Research Vehicle cockpit simulator was linked in real-time to the Center/TRACON Automation System (CTAS) for the experiment. Approximately 30 hours of simulation testing were conducted over a three week period. Active airline pilot crews and active Center controller teams participated as test subjects. Results from the experiment indicate the potential for successful incorporation of airplane preferred arrival trajectories in the CTAS automation environment. Controllers were able to consistently and effectively negotiate nominally conflict-free trajectories with pilots flying a 4D-FMS-equipped airplane. The negotiated trajectories were substantially closer to the airplane's preference than would have otherwise been possible without the PNP. Airplane fuel savings relative to baseline CTAS were achieved in the test scenarios. The datalink procedures and clearances developed for this experiment, while providing the necessary functionality, were found to be operationally unacceptable to the pilots. Additional pilot control and understanding of the proposed airplane-preferred trajectory and a simplified clearance procedure were cited as necessary for operational implementation of the concept. From the controllers' perspective, the main concerns were the ability of the 4D airplane to accurately track the negotiated trajectory and the workload required to support the PNP as implemented in this study.

Design and development of polyphenylene oxide foam as a reusable internal insulation for LH2 tanks

NASA Technical Reports Server (NTRS)

1975-01-01

Material specification and fabrication process procedures for foam production are presented. The properties of mechanical strength, modulus of elasticity, density and thermal conductivity were measured and related to foam quality. Properties unique to the foam such as a gas layer insulation, density gradient parallel to the fiber direction, and gas flow conductance in both directions were correlated with foam quality. Inspection and quality control tests procedures are outlined and photographs of test equipment and test specimens are shown.

Testing procedures for carbon fiber reinforced plastic components

NASA Technical Reports Server (NTRS)

Gosse, H. J.; Kaitatzidi, M.; Roth, S.

1977-01-01

Tests for studying the basic material are considered and quality control investigations involving preimpregnated materials (prepreg) are discussed. Attention is given to the prepreg area weight, the fiber area weight of prepregs, the resin content, volatile components, the effective thickness, resin flow, the resistance to bending strain, tensile strength, and shear strength. A description of tests conducted during the manufacturing process is also presented, taking into account X-ray methods, approaches of neutron radiography, ultrasonic procedures, resonance methods and impedance studies.

Processing Studies for Optically Transparent La(2)O(3)-Doped Y(2)O(3).

DTIC Science & Technology

1986-07-31

sintering. EXPERIMENTAL PROCEDURE ’ "’ The control powder (A) used in this investigation was prepared by a standard oxalate coprecip- itation procedure...Possible sources of CO2 are the decomposition of any oxalate remaining after calcination and/or formation of ’.’ carbonates during exposure to air. The...all the volatiles are removed from oxalate -derived powders during calcining or prefiring to 15000C. C02 is the major species present and probably

Preliminary Investigation of Time Remaining Display on the Computer-based Emergency Operating Procedure

NASA Astrophysics Data System (ADS)

Suryono, T. J.; Gofuku, A.

2018-02-01

One of the important thing in the mitigation of accidents in nuclear power plant accidents is time management. The accidents should be resolved as soon as possible in order to prevent the core melting and the release of radioactive material to the environment. In this case, operators should follow the emergency operating procedure related with the accident, in step by step order and in allowable time. Nowadays, the advanced main control rooms are equipped with computer-based procedures (CBPs) which is make it easier for operators to do their tasks of monitoring and controlling the reactor. However, most of the CBPs do not include the time remaining display feature which informs operators of time available for them to execute procedure steps and warns them if the they reach the time limit. Furthermore, the feature will increase the awareness of operators about their current situation in the procedure. This paper investigates this issue. The simplified of emergency operating procedure (EOP) of steam generator tube rupture (SGTR) accident of PWR plant is applied. In addition, the sequence of actions on each step of the procedure is modelled using multilevel flow modelling (MFM) and influenced propagation rule. The prediction of action time on each step is acquired based on similar case accidents and the Support Vector Regression. The derived time will be processed and then displayed on a CBP user interface.

Seismicity of the Bering Glacier Region: Inferences from Relocations Using Data from STEEP

NASA Astrophysics Data System (ADS)

Panessa, A. L.; Pavlis, G. L.; Hansen, R. A.; Ruppert, N.

2008-12-01

We relocated earthquakes recorded from 1990 to 2007 in the area of the Bering Glacier in southeastern Alaska to test a hypothesis that faults in this area are linked to glaciers. We used waveform correlation to improve arrival time measurements for data from all broadband channels including all the data from the STEEP experiment. We used a novel form of correlation based on interactive array processing of common receiver gathers linked to a three-dimensional grid of control points. This procedure produced 8556 gathers that we processed interactively to produce improved arrival time estimates. The interactive procedure allowed us to select which events in each gather were sufficiently similar to warrant correlation. Redundancy in the result was resolved in a secondary correlation that aligned event stacks of the same station-event pair associated with multiple control points. This procedure yielded only 2240 waveforms that correlated and modified only a total of 524 arrivals in a total database of 12263 arrivals. The correlation procedure changed arrival times on 145 of 509 events in this database. Events with arrivals constrained by correlation were not clustered but were randomly distributed throughout the study area. We used a version of the Progressive Multiple Event Location (PMEL) that analyzed data at each control point to invert for relative locations and a set of path anomalies for each control point. We applied the PMEL procedure with different velocity models and constraints and compared the results to a HypoDD solution produced from the original arrival time data. The relocations are all significant improvements from the standard single-event, catalog locations. The relocations suggest the seismicity in this region is mostly linked to fold and thrust deformation in the Yakatat block. There is a suggestion of a north-dipping trend to much of the seismicity, but the dominant trend is a fairly diffuse cloud of events largely confined to the Yakatat block south of the Bagley Icefield. This is consistent with the recently published tectonic model by Berger et al. (2008).

[Quality management in emergency departments: Lack of uniform standards for fact-based controlling].

PubMed

Ries, M; Christ, M

2015-11-01

The general high occupancy of emergency departments during the winter months of 2014/2015 outlined deficits in health politics. Whether on the regional, province, or federal level, verifiable and accepted figures to enable in depth analysis and fact-based controlling of emergency care systems are lacking. As the first step, reasons for the current situation are outlined in order to developed concrete recommendations for individual hospitals. This work is based on a selective literature search with focus on quality management, ratio driven management, and process management within emergency departments as well as personal experience with implementation of a key ratio system in a German maximum care hospital. The insufficient integration of emergencies into the DRG systematic, the role as gatekeeper between inpatient and outpatient care sector, the decentralized organization of emergency departments in many hospitals, and the inconsistent representation within the medical societies can be mentioned as reasons for the lack of key ratio systems. In addition to the important role within treatment procedures, emergency departments also have an immense economic importance. Consequently, the management of individual hospitals should promote implementation of key ratio systems to enable controlling of emergency care processes. Thereby the perspectives finance, employees, processes as well as partners and patients should be equally considered. Within the process perspective, milestones could be used to enable detailed controlling of treatment procedures. An implementation of key ratio systems without IT support is not feasible; thus, existing digital data should be used and future data analysis should already be considered during implementation of new IT systems.

A semi-automated image analysis procedure for in situ plankton imaging systems.

PubMed

Bi, Hongsheng; Guo, Zhenhua; Benfield, Mark C; Fan, Chunlei; Ford, Michael; Shahrestani, Suzan; Sieracki, Jeffery M

2015-01-01

Plankton imaging systems are capable of providing fine-scale observations that enhance our understanding of key physical and biological processes. However, processing the large volumes of data collected by imaging systems remains a major obstacle for their employment, and existing approaches are designed either for images acquired under laboratory controlled conditions or within clear waters. In the present study, we developed a semi-automated approach to analyze plankton taxa from images acquired by the ZOOplankton VISualization (ZOOVIS) system within turbid estuarine waters, in Chesapeake Bay. When compared to images under laboratory controlled conditions or clear waters, images from highly turbid waters are often of relatively low quality and more variable, due to the large amount of objects and nonlinear illumination within each image. We first customized a segmentation procedure to locate objects within each image and extracted them for classification. A maximally stable extremal regions algorithm was applied to segment large gelatinous zooplankton and an adaptive threshold approach was developed to segment small organisms, such as copepods. Unlike the existing approaches for images acquired from laboratory, controlled conditions or clear waters, the target objects are often the majority class, and the classification can be treated as a multi-class classification problem. We customized a two-level hierarchical classification procedure using support vector machines to classify the target objects (< 5%), and remove the non-target objects (> 95%). First, histograms of oriented gradients feature descriptors were constructed for the segmented objects. In the first step all non-target and target objects were classified into different groups: arrow-like, copepod-like, and gelatinous zooplankton. Each object was passed to a group-specific classifier to remove most non-target objects. After the object was classified, an expert or non-expert then manually removed the non-target objects that could not be removed by the procedure. The procedure was tested on 89,419 images collected in Chesapeake Bay, and results were consistent with visual counts with >80% accuracy for all three groups.

A Semi-Automated Image Analysis Procedure for In Situ Plankton Imaging Systems

PubMed Central

Bi, Hongsheng; Guo, Zhenhua; Benfield, Mark C.; Fan, Chunlei; Ford, Michael; Shahrestani, Suzan; Sieracki, Jeffery M.

2015-01-01

Plankton imaging systems are capable of providing fine-scale observations that enhance our understanding of key physical and biological processes. However, processing the large volumes of data collected by imaging systems remains a major obstacle for their employment, and existing approaches are designed either for images acquired under laboratory controlled conditions or within clear waters. In the present study, we developed a semi-automated approach to analyze plankton taxa from images acquired by the ZOOplankton VISualization (ZOOVIS) system within turbid estuarine waters, in Chesapeake Bay. When compared to images under laboratory controlled conditions or clear waters, images from highly turbid waters are often of relatively low quality and more variable, due to the large amount of objects and nonlinear illumination within each image. We first customized a segmentation procedure to locate objects within each image and extracted them for classification. A maximally stable extremal regions algorithm was applied to segment large gelatinous zooplankton and an adaptive threshold approach was developed to segment small organisms, such as copepods. Unlike the existing approaches for images acquired from laboratory, controlled conditions or clear waters, the target objects are often the majority class, and the classification can be treated as a multi-class classification problem. We customized a two-level hierarchical classification procedure using support vector machines to classify the target objects (< 5%), and remove the non-target objects (> 95%). First, histograms of oriented gradients feature descriptors were constructed for the segmented objects. In the first step all non-target and target objects were classified into different groups: arrow-like, copepod-like, and gelatinous zooplankton. Each object was passed to a group-specific classifier to remove most non-target objects. After the object was classified, an expert or non-expert then manually removed the non-target objects that could not be removed by the procedure. The procedure was tested on 89,419 images collected in Chesapeake Bay, and results were consistent with visual counts with >80% accuracy for all three groups. PMID:26010260

44 CFR 152.9 - Reconsideration.

Code of Federal Regulations, 2010 CFR

2010-10-01

... HOMELAND SECURITY FIRE PREVENTION AND CONTROL ASSISTANCE TO FIREFIGHTERS GRANT PROGRAM § 152.9... technical or procedural error in the processing of the application and can substantiate such assertions. As... experts, we cannot consider requests for reconsideration based upon the merits of an original application...

49 CFR 178.70 - Approval of UN pressure receptacles.

Code of Federal Regulations, 2010 CFR

2010-10-01

... facility as specified in § 178.69. (7) Design specifications and manufacturing drawings, showing components... compliance with the applicable pressure receptacle design standard. (8) Manufacturing procedures and any applicable standards that describe in detail the manufacturing processes and control. (9) Design type...

Ground control requirements for precision processing of ERTS images

USGS Publications Warehouse

Burger, Thomas C.

1973-01-01

With the successful flight of the ERTS-1 satellite, orbital height images are available for precision processing into products such as 1:1,000,000-scale photomaps and enlargements up to 1:250,000 scale. In order to maintain positional error below 100 meters, control points for the precision processing must be carefully selected, clearly definitive on photos in both X and Y. Coordinates of selected control points measured on existing ½ and 15-minute standard maps provide sufficient accuracy for any space imaging system thus far defined. This procedure references the points to accepted horizontal and vertical datums. Maps as small as 1:250,000 scale can be used as source material for coordinates, but to maintain the desired accuracy, maps of 1:100,000 and larger scale should be used when available.

Human Factors Process Task Analysis Liquid Oxygen Pump Acceptance Test Procedure for the Advanced Technology Development Center

NASA Technical Reports Server (NTRS)

Diorio, Kimberly A.

2002-01-01

A process task analysis effort was undertaken by Dynacs Inc. commencing in June 2002 under contract from NASA YA-D6. Funding was provided through NASA's Ames Research Center (ARC), Code M/HQ, and Industrial Engineering and Safety (IES). The John F. Kennedy Space Center (KSC) Engineering Development Contract (EDC) Task Order was 5SMA768. The scope of the effort was to conduct a Human Factors Process Failure Modes and Effects Analysis (HF PFMEA) of a hazardous activity and provide recommendations to eliminate or reduce the effects of errors caused by human factors. The Liquid Oxygen (LOX) Pump Acceptance Test Procedure (ATP) was selected for this analysis. The HF PFMEA table (see appendix A) provides an analysis of six major categories evaluated for this study. These categories include Personnel Certification, Test Procedure Format, Test Procedure Safety Controls, Test Article Data, Instrumentation, and Voice Communication. For each specific requirement listed in appendix A, the following topics were addressed: Requirement, Potential Human Error, Performance-Shaping Factors, Potential Effects of the Error, Barriers and Controls, Risk Priority Numbers, and Recommended Actions. This report summarizes findings and gives recommendations as determined by the data contained in appendix A. It also includes a discussion of technology barriers and challenges to performing task analyses, as well as lessons learned. The HF PFMEA table in appendix A recommends the use of accepted and required safety criteria in order to reduce the risk of human error. The items with the highest risk priority numbers should receive the greatest amount of consideration. Implementation of the recommendations will result in a safer operation for all personnel.

LMI designmethod for networked-based PID control

NASA Astrophysics Data System (ADS)

Souza, Fernando de Oliveira; Mozelli, Leonardo Amaral; de Oliveira, Maurício Carvalho; Palhares, Reinaldo Martinez

2016-10-01

In this paper, we propose a methodology for the design of networked PID controllers for second-order delayed processes using linear matrix inequalities. The proposed procedure takes into account time-varying delay on the plant, time-varying delays induced by the network and packed dropouts. The design is carried on entirely using a continuous-time model of the closed-loop system where time-varying delays are used to represent sampling and holding occurring in a discrete-time digital PID controller.

Quality improvement through implementation of discharge order reconciliation.

PubMed

Lu, Yun; Clifford, Pamela; Bjorneby, Andreas; Thompson, Bruce; VanNorman, Samuel; Won, Katie; Larsen, Kevin

2013-05-01

A coordinated multidisciplinary process to reduce medication errors related to patient discharges to skilled-nursing facilities (SNFs) is described. After determining that medication errors were a frequent cause of readmission among patients discharged to SNFs, a medical center launched a two-phase quality-improvement project focused on cardiac and medical patients. Phase one of the project entailed a three-month failure modes and effects analysis of existing procedures discharge, followed by the development and pilot testing of a multidisciplinary, closed-loop workflow process involving staff and resident physicians, clinical nurse coordinators, and clinical pharmacists. During pilot testing of the new workflow process, the rate of discharge medication errors involving SNF patients was tracked, and data on medication-related readmissions in a designated intervention group (n = 87) and a control group of patients (n = 1893) discharged to SNFs via standard procedures during a nine-month period were collected, with the data stratified using severity of illness (SOI) classification. Analysis of the collected data indicated a cumulative 30-day medication-related readmission rate for study group patients in the minor, moderate, and major SOI categories of 5.4% (4 of 74 patients), compared with a rate of 9.5% (169 of 1780 patients) in the control group. In phase 2 of the project, the revised SNF discharge medication reconciliation procedure was implemented throughout the hospital; since hospitalwide implementation of the new workflow, the readmission rate for SNF patients has been maintained at about 6.7%. Implementing a standardized discharge order reconciliation process that includes pharmacists led to decreased readmission rates and improved care for patients discharged to SNFs.

Command Process Modeling & Risk Analysis

NASA Technical Reports Server (NTRS)

Meshkat, Leila

2011-01-01

Commanding Errors may be caused by a variety of root causes. It's important to understand the relative significance of each of these causes for making institutional investment decisions. One of these causes is the lack of standardized processes and procedures for command and control. We mitigate this problem by building periodic tables and models corresponding to key functions within it. These models include simulation analysis and probabilistic risk assessment models.

Quality Control Analysis of Selected Aspects of Programs Administered by the Bureau of Student Financial Assistance. Task 1 and Quality Control Sample; Error-Prone Modeling Analysis Plan.

ERIC Educational Resources Information Center

Saavedra, Pedro; And Others

Parameters and procedures for developing an error-prone model (EPM) to predict financial aid applicants who are likely to misreport on Basic Educational Opportunity Grant (BEOG) applications are introduced. Specifications to adapt these general parameters to secondary data analysis of the Validation, Edits, and Applications Processing Systems…

Application of optimal control principles to describe the supervisory control behavior of AAA crew members

NASA Technical Reports Server (NTRS)

Hale, C.; Valentino, G. J.

1982-01-01

Supervisory decision making and control behavior within a C(3) oriented, ground based weapon system is being studied. The program involves empirical investigation of the sequence of control strategies used during engagement of aircraft targets. An engagement is conceptually divided into several stages which include initial information processing activity, tracking, and ongoing adaptive control decisions. Following a brief description of model parameters, two experiments which served as initial investigation into the accuracy of assumptions regarding the importance of situation assessment in procedure selection are outlined. Preliminary analysis of the results upheld the validity of the assumptions regarding strategic information processing and cue-criterion relationship learning. These results indicate that this model structure should be useful in studies of supervisory decision behavior.

In-line verification of linewidth uniformity for 0.18 and below: design rule reticles

NASA Astrophysics Data System (ADS)

Tan, TaiSheng; Kuo, Shen C.; Wu, Clare; Falah, Reuven; Hemar, Shirley; Sade, Amikam; Gottlib, Gidon

2000-07-01

Mask making process development and control is addressed using a reticle inspection tool equipped with the new revolutionized application called LBM-Linewidth Bias Monitoring. In order to use the LBM for mask-making process control, procedures and corresponding test plates are a developed, such that routine monitoring of the manufacturing process discloses process variation and machine variation. At the same time systematic variation are studied and either taken care of or taken into consideration to allow successful production line work. In this paper the contribution of the LBM for mask quality monitoring is studied with respect to dense layers, e.g. DRAM. Another aspect of this application - the detection of very small CD mis-uniformity areas is discussed.

Applying Lean-Six-Sigma Methodology in radiotherapy: Lessons learned by the breast daily repositioning case.

PubMed

Mancosu, Pietro; Nicolini, Giorgia; Goretti, Giulia; De Rose, Fiorenza; Franceschini, Davide; Ferrari, Chiara; Reggiori, Giacomo; Tomatis, Stefano; Scorsetti, Marta

2018-05-01

Lean Six Sigma Methodology (LSSM) was introduced in industry to provide near-perfect services to large processes, by reducing improbable occurrence. LSSM has been applied to redesign the 2D-2D breast repositioning process (Lean) by the retrospective analysis of the database (Six Sigma). Breast patients with daily 2D-2D matching before RT were considered. The five DMAIC (define, measure, analyze, improve, and control) LSSM steps were applied. The process was retrospectively measured over 30 months (7/2014-12/2016) by querying the RT Record&Verify database. Two Lean instruments (Poka-Yoke and Visual Management) were considered for advancing the process. The new procedure was checked over 6 months (1-6/2017). 14,931 consecutive shifts from 1342 patients were analyzed. Only 0.8% of patients presented median shifts >1 cm. The major observed discrepancy was the monthly percentage of fractions with almost zero shifts (AZS = 13.2% ± 6.1%). Ishikawa fishbone diagram helped in defining the main discrepancy con-causes. Procedure harmonization involving a multidisciplinary team to increase confidence in matching procedure was defined. AZS was reduced to 4.8% ± 0.6%. Furthermore, distribution symmetry improvement (Skewness moved from 1.4 to 1.1) and outlier reduction, verified by Kurtosis diminution, demonstrated a better "normalization" of the procedure after the LSSM application. LSSM was implemented in a RT department, allowing to redesign the breast repositioning matching procedure. Copyright © 2018 Elsevier B.V. All rights reserved.

Software control and system configuration management: A systems-wide approach

NASA Technical Reports Server (NTRS)

Petersen, K. L.; Flores, C., Jr.

1984-01-01

A comprehensive software control and system configuration management process for flight-crucial digital control systems of advanced aircraft has been developed and refined to insure efficient flight system development and safe flight operations. Because of the highly complex interactions among the hardware, software, and system elements of state-of-the-art digital flight control system designs, a systems-wide approach to configuration control and management has been used. Specific procedures are implemented to govern discrepancy reporting and reconciliation, software and hardware change control, systems verification and validation testing, and formal documentation requirements. An active and knowledgeable configuration control board reviews and approves all flight system configuration modifications and revalidation tests. This flexible process has proved effective during the development and flight testing of several research aircraft and remotely piloted research vehicles with digital flight control systems that ranged from relatively simple to highly complex, integrated mechanizations.

Advanced model-based control strategies for the intensification of upstream and downstream processing in mAb production.

PubMed

Papathanasiou, Maria M; Quiroga-Campano, Ana L; Steinebach, Fabian; Elviro, Montaña; Mantalaris, Athanasios; Pistikopoulos, Efstratios N

2017-07-01

Current industrial trends encourage the development of sustainable, environmentally friendly processes with minimal energy and material consumption. In particular, the increasing market demand in biopharmaceutical industry and the tight regulations in product quality necessitate efficient operating procedures that guarantee products of high purity. In this direction, process intensification via continuous operation paves the way for the development of novel, eco-friendly processes, characterized by higher productivity and lower production costs. This work focuses on the development of advanced control strategies for (i) a cell culture system in a bioreactor and (ii) a semicontinuous purification process. More specifically, we consider a fed-batch culture of GS-NS0 cells and the semicontinuous Multicolumn Countercurrent Solvent Gradient Purification (MCSGP) for the purification process. The controllers are designed following the PAROC framework/software platform and their capabilities are assessed in silico, against the process models. It is demonstrated that the proposed controllers efficiently manage to increase the system productivity, returning strategies that can lead to continuous, stable process operation. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 33:966-988, 2017. © 2017 American Institute of Chemical Engineers.

[Establishment and application of "multi-dimensional structure and process dynamic quality control technology system" in preparation products of traditional Chinese medicine (I)].

PubMed

Gu, Jun-Fei; Feng, Liang; Zhang, Ming-Hua; Wu, Chan; Jia, Xiao-Bin

2013-11-01

Safety is an important component of the quality control of traditional Chinese medicine (TCM) preparation products, as well as an important guarantee for clinical application. Currently, the quality control of TCMs in Chinese Pharmacopoeia mostly focuses on indicative compounds for TCM efficacy. TCM preparations are associated with multiple links, from raw materials to products, and each procedure may have impacts on the safety of preparation. We make a summary and analysis on the factors impacting safety during the preparation of TCM products, and then expound the important role of the "multi-dimensional structure and process dynamic quality control technology system" in the quality safety of TCM preparations. Because the product quality of TCM preparation is closely related to the safety, the control over safety-related material basis is an important component of the product quality control of TCM preparations. The implementation of the quality control over the dynamic process of TCM preparations from raw materials to products, and the improvement of the TCM quality safety control at the microcosmic level help lay a firm foundation for the development of the modernization process of TCM preparations.

Optimization applications in aircraft engine design and test

NASA Technical Reports Server (NTRS)

Pratt, T. K.

1984-01-01

Starting with the NASA-sponsored STAEBL program, optimization methods based primarily upon the versatile program COPES/CONMIN were introduced over the past few years to a broad spectrum of engineering problems in structural optimization, engine design, engine test, and more recently, manufacturing processes. By automating design and testing processes, many repetitive and costly trade-off studies have been replaced by optimization procedures. Rather than taking engineers and designers out of the loop, optimization has, in fact, put them more in control by providing sophisticated search techniques. The ultimate decision whether to accept or reject an optimal feasible design still rests with the analyst. Feedback obtained from this decision process has been invaluable since it can be incorporated into the optimization procedure to make it more intelligent. On several occasions, optimization procedures have produced novel designs, such as the nonsymmetric placement of rotor case stiffener rings, not anticipated by engineering designers. In another case, a particularly difficult resonance contraint could not be satisfied using hand iterations for a compressor blade, when the STAEBL program was applied to the problem, a feasible solution was obtained in just two iterations.

Process for testing a xenon gas feed system of a hollow cathode assembly

NASA Technical Reports Server (NTRS)

Patterson, Michael J. (Inventor); Verhey, Timothy R. R. (Inventor); Soulas, George C. (Inventor)

2004-01-01

The design and manufacturing processes for Hollow Cathode Assemblies (HCA's) that operate over a broad range of emission currents up to 30 Amperes, at low potentials, with lifetimes in excess of 17,500 hours. The processes include contamination control procedures which cover hollow cathode component cleaning procedures, gas feed system designs and specifications, and hollow cathode activation and operating procedures to thereby produce cathode assemblies that have demonstrated stable and repeatable operating conditions, for both the discharge current and voltage. The HCA of this invention provides lifetimes of greater than 10,000 hours, and expected lifetimes of greater than 17,500 hours, whereas the present state-of-the-art is less than 500 hours at emission currents in excess of 1 Ampere. Stable operation is provided over a large range of operating emission currents, up to a 6:1 ratio, and this HCA can emit electron currents of up to 30 Amperes in magnitude to an external anode that simulates the current drawn to a space plasma, at voltages of less than 20 Volts.

Process for Ignition of Gaseous Electrical Discharge Between Electrodes of a Hollow Cathode Assembly

NASA Technical Reports Server (NTRS)

Patterson, Michael J. (Inventor); Verhey, Timothy R. R. (Inventor); Soulas, George C. (Inventor)

2000-01-01

The design and manufacturing processes for Hollow Cathode Assemblies (HCA's) that operate over a broad range of emission currents up to 30 Amperes, at low potentials, with lifetimes in excess of 17,500 hours. The processes include contamination control procedures which cover hollow cathode component cleaning procedures, gas feed system designs and specifications, and hollow cathode activation and operating procedures to thereby produce cathode assemblies that have demonstrated stable and repeatable operating conditions, for both the discharge current and voltage. The HCA of this invention provides lifetimes of greater than 10,000 hours, and expected lifetimes of greater than 17,500 hours, whereas the present state-of-the-art is less than 500 hours at emission currents in excess of 1 Ampere. Stable operation is provided over a large range of operating emission currents, up to a 6:1 ratio, and this HCA can emit electron currents of up to 30 Amperes in magnitude to an external anode that simulates the current drawn to a space plasma, at voltages of less than 20 Volts.

Refractive microlensarray made of silver-halide sensitized gelatin (SHSG) etched by enzyme with SLM-based lithography

NASA Astrophysics Data System (ADS)

Guo, Xiaowei; Chen, Mingyong; Zhu, Jianhua; Ma, Yanqin; Du, Jinglei; Guo, Yongkang; Du, Chunlei

2006-01-01

A novel method for the fabrication of continuous micro-optical components is presented in this paper. It employs a computer controlled digital-micromirror-device(DMD TM) as a switchable projection mask and silver-halide sensitized gelatin (SHSG) as recording material. By etching SHSG with enzyme solution, the micro-optical components with relief modulation can be generated through special processing procedures. The principles of etching SHSG with enzyme and theoretical analysis for deep etching are also discussed in detail, and the detailed quantitative experiments on the processing procedures are conducted to determine optimum technique parameters. A good linear relationship within a depth range of 4μm was experimentally obtained between exposure dose and relief depth. At last, the microlensarray with 256.8μm radius and 2.572μm depth was achieved. This method is simple, cheap and the aberration in processing procedures can be corrected in the step of designing mask, so it is a practical method to fabricate good continuous profile for low-volume production.

Certification of highly complex safety-related systems.

PubMed

Reinert, D; Schaefer, M

1999-01-01

The BIA has now 15 years of experience with the certification of complex electronic systems for safety-related applications in the machinery sector. Using the example of machining centres this presentation will show the systematic procedure for verifying and validating control systems using Application Specific Integrated Circuits (ASICs) and microcomputers for safety functions. One section will describe the control structure of machining centres with control systems using "integrated safety." A diverse redundant architecture combined with crossmonitoring and forced dynamization is explained. In the main section the steps of the systematic certification procedure are explained showing some results of the certification of drilling machines. Specification reviews, design reviews with test case specification, statistical analysis, and walk-throughs are the analytical measures in the testing process. Systematic tests based on the test case specification, Electro Magnetic Interference (EMI), and environmental testing, and site acceptance tests on the machines are the testing measures for validation. A complex software driven system is always undergoing modification. Most of the changes are not safety-relevant but this has to be proven. A systematic procedure for certifying software modifications is presented in the last section of the paper.

Data Quality Assurance and Control for AmeriFlux Network at CDIAC, ORNL

NASA Astrophysics Data System (ADS)

Shem, W.; Boden, T.; Krassovski, M.; Yang, B.

2014-12-01

The Carbon Dioxide Information Analysis Center (CDIAC) at the Oak Ridge National Laboratory (ORNL) serves as the long-term data repository for the AmeriFlux network. Datasets currently available include hourly or half-hourly meteorological and flux observations, biological measurement records, and synthesis data products. Currently there is a lack of standardized nomenclature and specifically designed procedures for data quality assurance/control in processing and handling micrometeorological and ecological data at individual flux sites. CDIAC's has bridged this gap by providing efficient and accurate procedures for data quality control and standardization of the results for easier assimilation by the models used in climate science. In this presentation we highlight the procedures we have put in place to scrutinize continuous flux and meteorological data within Ameriflux network. We itemize some basic data quality issues that we have observed over the past years and include some examples of typical data quality issues. Such issues, e.g., incorrect time-stamping, poor calibration or maintenance of instruments, missing or incomplete metadata and others that are commonly over-looked by PI's, invariably impact the time-series observations.

Enhancement of face recognition learning in patients with brain injury using three cognitive training procedures.

PubMed

Powell, Jane; Letson, Susan; Davidoff, Jules; Valentine, Tim; Greenwood, Richard

2008-04-01

Twenty patients with impairments of face recognition, in the context of a broader pattern of cognitive deficits, were administered three new training procedures derived from contemporary theories of face processing to enhance their learning of new faces: semantic association (being given additional verbal information about the to-be-learned faces); caricaturing (presentation of caricatured versions of the faces during training and veridical versions at recognition testing); and part recognition (focusing patients on distinctive features during the training phase). Using a within-subjects design, each training procedure was applied to a different set of 10 previously unfamiliar faces and entailed six presentations of each face. In a "simple exposure" control procedure (SE), participants were given six presentations of another set of faces using the same basic protocol but with no further elaboration. Order of the four procedures was counterbalanced, and each condition was administered on a different day. A control group of 12 patients with similar levels of face recognition impairment were trained on all four sets of faces under SE conditions. Compared to the SE condition, all three training procedures resulted in more accurate discrimination between the 10 studied faces and 10 distractor faces in a post-training recognition test. This did not reflect any intrinsic lesser memorability of the faces used in the SE condition, as evidenced by the comparable performance across face sets by the control group. At the group level, the three experimental procedures were of similar efficacy, and associated cognitive deficits did not predict which technique would be most beneficial to individual patients; however, there was limited power to detect such associations. Interestingly, a pure prosopagnosic patient who was tested separately showed benefit only from the part recognition technique. Possible mechanisms for the observed effects, and implications for rehabilitation, are discussed.

Fat-free mass is not lower 24 months postbariatric surgery than nonoperated matched controls

PubMed Central

Strain, Gladys Witt; Ebel, Faith; Honohan, Jamie; Gagner, Michel; Dakin, Gregory F.; Pomp, Alfons; Gallagher, Dympna

2017-01-01

Objective Concerns about an excessive loss of fat-free mass (FFM) after bariatric surgery prompted this comparison of operated versus matched nonoperated controls regarding FFM. Setting University Hospital and University Research Unit in an urban medical center. Methods Body composition with bioelectric impedance (Tanita 310, Tanita Corp, Arlington Heights, IL) was measured approximately 2 years after bariatric surgery in weight stable patients and nonoperated weight stable controls matched for body mass index (BMI), gender, and age. t tests provided comparisons. Analysis of variance was used to compare FFM changes for 4 procedures. Levene’s test evaluated variance. Results Patients (n = 252; 24.7 ± 15 mo after surgery) and nonoperated controls (n = 252) were matched for gender (71.8% female), age (44.5 ± 11.0 yr), and BMI (32.8 ± 7.0 kg/m2). Patients had different surgical procedures: 107 gastric bypasses (RYGBs), 62 biliopancreatic diversions with duodenal switch (BPD/DSs), 40 adjustable gastric bands (AGBs), and 43 sleeve gastrectomies (LSGs). FFM percentage was significantly higher in the operated patients than controls, 66% versus 62%, P < .0001. For 3 procedures, the FFM was significantly higher; however, AGBs changed only 7.3 BMI units and FFM was not significantly different from their matched controls, 59.8% versus 58.2%. Across surgical groups, FFM percentage differed, P < .0001 (RYGB 66.5 ± 9.2%, BPD/DS 74.0 ± 9.3%, AGB 59.8 ± 7.0%, LSG 59.6 ± 9.3%). Variance was not different (P = .17). Conclusion Weight-reduced bariatric surgery patients have greater FFM compared with nonoperated matched controls. These findings support surgically assisted weight loss as a physiologic process and in general patients do not suffer from excessive FFM depletion after bariatric procedures. PMID:27387700

On-Orbit Multi-Field Wavefront Control with a Kalman Filter

NASA Technical Reports Server (NTRS)

Lou, John; Sigrist, Norbert; Basinger, Scott; Redding, David

2008-01-01

A document describes a multi-field wavefront control (WFC) procedure for the James Webb Space Telescope (JWST) on-orbit optical telescope element (OTE) fine-phasing using wavefront measurements at the NIRCam pupil. The control is applied to JWST primary mirror (PM) segments and secondary mirror (SM) simultaneously with a carefully selected ordering. Through computer simulations, the multi-field WFC procedure shows that it can reduce the initial system wavefront error (WFE), as caused by random initial system misalignments within the JWST fine-phasing error budget, from a few dozen micrometers to below 50 nm across the entire NIRCam Field of View, and the WFC procedure is also computationally stable as the Monte-Carlo simulations indicate. With the incorporation of a Kalman Filter (KF) as an optical state estimator into the WFC process, the robustness of the JWST OTE alignment process can be further improved. In the presence of some large optical misalignments, the Kalman state estimator can provide a reasonable estimate of the optical state, especially for those degrees of freedom that have a significant impact on the system WFE. The state estimate allows for a few corrections to the optical state to push the system towards its nominal state, and the result is that a large part of the WFE can be eliminated in this step. When the multi-field WFC procedure is applied after Kalman state estimate and correction, the stability of fine-phasing control is much more certain. Kalman Filter has been successfully applied to diverse applications as a robust and optimal state estimator. In the context of space-based optical system alignment based on wavefront measurements, a KF state estimator can combine all available wavefront measurements, past and present, as well as measurement and actuation error statistics to generate a Maximum-Likelihood optimal state estimator. The strength and flexibility of the KF algorithm make it attractive for use in real-time optical system alignment when WFC alone cannot effectively align the system.

Process monitoring of additive manufacturing by using optical tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zenzinger, Guenter, E-mail: guenter.zenzinger@mtu.de, E-mail: alexander.ladewig@mtu.de; Bamberg, Joachim, E-mail: guenter.zenzinger@mtu.de, E-mail: alexander.ladewig@mtu.de; Ladewig, Alexander, E-mail: guenter.zenzinger@mtu.de, E-mail: alexander.ladewig@mtu.de

2015-03-31

Parts fabricated by means of additive manufacturing are usually of complex shape and owing to the fabrication procedure by using selective laser melting (SLM), potential defects and inaccuracies are often very small in lateral size. Therefore, an adequate quality inspection of such parts is rather challenging, while non-destructive-techniques (NDT) are difficult to realize, but considerable efforts are necessary in order to ensure the quality of SLM-parts especially used for aerospace components. Thus, MTU Aero Engines is currently focusing on the development of an Online Process Control system which monitors and documents the complete welding process during the SLM fabrication procedure.more » A high-resolution camera system is used to obtain images, from which tomographic data for a 3dim analysis of SLM-parts are processed. From the analysis, structural irregularities and structural disorder resulting from any possible erroneous melting process become visible and may be allocated anywhere within the 3dim structure. Results of our optical tomography (OT) method as obtained on real defects are presented.« less

Quality-assurance data for routine water analyses by the U.S. Geological Survey laboratory in Troy, New York - July 2003 through June 2005

USGS Publications Warehouse

Lincoln, Tricia A.; Horan-Ross, Debra A.; McHale, Michael R.; Lawrence, Gregory B.

2009-01-01

The laboratory for analysis of low-ionic-strength water at the U.S. Geological Survey (USGS) Water Science Center in Troy, N.Y., analyzes samples collected by USGS projects throughout the Northeast. The laboratory's quality-assurance program is based on internal and interlaboratory quality-assurance samples and quality-control procedures that were developed to ensure proper sample collection, processing, and analysis. The quality-assurance and quality-control data were stored in the laboratory's Lab Master data-management system, which provides efficient review, compilation, and plotting of data. This report presents and discusses results of quality-assurance and quality control samples analyzed from July 2003 through June 2005. Results for the quality-control samples for 20 analytical procedures were evaluated for bias and precision. Control charts indicate that data for five of the analytical procedures were occasionally biased for either high-concentration or low-concentration samples but were within control limits; these procedures were: acid-neutralizing capacity, total monomeric aluminum, pH, silicon, and sodium. Seven of the analytical procedures were biased throughout the analysis period for the high-concentration sample, but were within control limits; these procedures were: dissolved organic carbon, chloride, nitrate (ion chromatograph), nitrite, silicon, sodium, and sulfate. The calcium and magnesium procedures were biased throughout the analysis period for the low-concentration sample, but were within control limits. The total aluminum and specific conductance procedures were biased for the high-concentration and low-concentration samples, but were within control limits. Results from the filter-blank and analytical-blank analyses indicate that the procedures for 17 of 18 analytes were within control limits, although the concentrations for blanks were occasionally outside the control limits. The data-quality objective was not met for dissolved organic carbon. Sampling and analysis precision are evaluated herein in terms of the coefficient of variation obtained for triplicate samples in the procedures for 18 of the 22 analytes. At least 85 percent of the samples met data-quality objectives for all analytes except total monomeric aluminum (82 percent of samples met objectives), total aluminum (77 percent of samples met objectives), chloride (80 percent of samples met objectives), fluoride (76 percent of samples met objectives), and nitrate (ion chromatograph) (79 percent of samples met objectives). The ammonium and total dissolved nitrogen did not meet the data-quality objectives. Results of the USGS interlaboratory Standard Reference Sample (SRS) Project indicated good data quality over the time period, with ratings for each sample in the satisfactory, good, and excellent ranges or less than 10 percent error. The P-sample (low-ionic-strength constituents) analysis had one marginal and two unsatisfactory ratings for the chloride procedure. The T-sample (trace constituents)analysis had two unsatisfactory ratings and one high range percent error for the aluminum procedure. The N-sample (nutrient constituents) analysis had one marginal rating for the nitrate procedure. Results of Environment Canada's National Water Research Institute (NWRI) program indicated that at least 84 percent of the samples met data-quality objectives for 11 of the 14 analytes; the exceptions were ammonium, total aluminum, and acid-neutralizing capacity. The ammonium procedure did not meet data quality objectives in all studies. Data-quality objectives were not met in 23 percent of samples analyzed for total aluminum and 45 percent of samples analyzed acid-neutralizing capacity. Results from blind reference-sample analyses indicated that data-quality objectives were met by at least 86 percent of the samples analyzed for calcium, chloride, fluoride, magnesium, pH, potassium, sodium, and sulfate. Data-quality objectives were not met by samples analyzed for fluoride. 

Intelligent flight control systems

NASA Technical Reports Server (NTRS)

Stengel, Robert F.

1993-01-01

The capabilities of flight control systems can be enhanced by designing them to emulate functions of natural intelligence. Intelligent control functions fall in three categories. Declarative actions involve decision-making, providing models for system monitoring, goal planning, and system/scenario identification. Procedural actions concern skilled behavior and have parallels in guidance, navigation, and adaptation. Reflexive actions are spontaneous, inner-loop responses for control and estimation. Intelligent flight control systems learn knowledge of the aircraft and its mission and adapt to changes in the flight environment. Cognitive models form an efficient basis for integrating 'outer-loop/inner-loop' control functions and for developing robust parallel-processing algorithms.

High-throughput biomonitoring of dioxins and polychlorinated biphenyls at the sub-picogram level in human serum.

PubMed

Focant, Jean-François; Eppe, Gauthier; Massart, Anne-Cécile; Scholl, Georges; Pirard, Catherine; De Pauw, Edwin

2006-10-13

We report on the use of a state-of-the-art method for the measurement of selected polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans and polychlorinated biphenyls in human serum specimens. The sample preparation procedure is based on manual small size solid-phase extraction (SPE) followed by automated clean-up and fractionation using multi-sorbent liquid chromatography columns. SPE cartridges and all clean-up columns are disposable. Samples are processed in batches of 20 units, including one blank control (BC) sample and one quality control (QC) sample. The analytical measurement is performed using gas chromatography coupled to isotope dilution high-resolution mass spectrometry. The sample throughput corresponds to one series of 20 samples per day, from sample reception to data quality cross-check and reporting, once the procedure has been started and series of samples keep being produced. Four analysts are required to ensure proper performances of the procedure. The entire procedure has been validated under International Organization for Standardization (ISO) 17025 criteria and further tested over more than 1500 unknown samples during various epidemiological studies. The method is further discussed in terms of reproducibility, efficiency and long-term stability regarding the 35 target analytes. Data related to quality control and limit of quantification (LOQ) calculations are also presented and discussed.

Recording and reproduction of microwave holograms using a scanning procedure and their subsequent optical processing

NASA Technical Reports Server (NTRS)

Hetsch, J.

1983-01-01

Intensity distributions in nonoptical wave fields can be visualized and stored on photosensitive material. In the case of microwaves, temperature effects can be utilized with the aid of liquid crystals to visualize intensity distributions. Particular advantages for the study of intensity distributions in microwave fields presents a scanning procedure in which a microcomputer is employed for the control of a probe and the storage of the measured data. The present investigation is concerned with the employment of such a scanning procedure for the recording and the reproduction of microwave holograms. The scanning procedure makes use of an approach discussed by Farhat, et al. (1973). An eight-bit microprocessor with 64 kBytes of RAM is employed together with a diskette storage system.

40 CFR 86.1825-01 - Durability demonstration procedures for refueling emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... shall use good engineering judgment in determining this process. (a) Service accumulation method. (1.... The manufacturer shall use good engineering judgement in developing this method. (2) The manufacturers... programs, all emission control components and systems (including both hardware and software) must be...

Isolation and Characterization of Chitosan-Producing Bacteria from Beaches of Chennai, India

PubMed Central

Kaur, Kuldeep; Dattajirao, Vikrant; Shrivastava, Vikas; Bhardwaj, Uma

2012-01-01

Chitosan is a deacetylated product of chitin produced by chitin deacetylase, an enzyme that hydrolyses acetamido groups of N-acetylglucosamine in chitin. Chitosan is a natural polymer that has great potential in biotechnology and in the biomedical and pharmaceutical industries. Commercially, it is produced from chitin via a harsh thermochemical process that shares most of the disadvantages of a multistep chemical procedure. It is environmentally unsafe and not easily controlled, leading to a broad and heterogeneous range of products. An alternative or complementary procedure exploiting the enzymatic deacetylation of chitin could potentially be employed, especially when a controlled and well-defined process is required. In this study, 20 strains of bacteria were isolated from soil samples collected from different beaches of Chennai, India. Of these 20 bacterial strains, only 2 strains (S3, S14) are potent degrader of chitin and they are also a good producer of the enzyme chitin deacetylase so as to release chitosan. PMID:22919468

Spaceport Command and Control System Software Development

NASA Technical Reports Server (NTRS)

Glasser, Abraham

2017-01-01

The Spaceport Command and Control System (SCCS) is the National Aeronautics and Space Administration's (NASA) launch control system for the Orion capsule and Space Launch System, the next generation manned rocket currently in development. This large system requires a large amount of intensive testing that will properly measure the capabilities of the system. Automating the test procedures would save the project money from human labor costs, as well as making the testing process more efficient. Therefore, the Exploration Systems Division (formerly the Electrical Engineering Division) at Kennedy Space Center (KSC) has recruited interns for the past two years to work alongside full-time engineers to develop these automated tests, as well as innovate upon the current automation process.

Stochastic optimal control of ultradiffusion processes with application to dynamic portfolio management

NASA Astrophysics Data System (ADS)

Marcozzi, Michael D.

2008-12-01

We consider theoretical and approximation aspects of the stochastic optimal control of ultradiffusion processes in the context of a prototype model for the selling price of a European call option. Within a continuous-time framework, the dynamic management of a portfolio of assets is effected through continuous or point control, activation costs, and phase delay. The performance index is derived from the unique weak variational solution to the ultraparabolic Hamilton-Jacobi equation; the value function is the optimal realization of the performance index relative to all feasible portfolios. An approximation procedure based upon a temporal box scheme/finite element method is analyzed; numerical examples are presented in order to demonstrate the viability of the approach.

Early process development of API applied to poorly water-soluble TBID.

PubMed

Meise, Marius; Niggemann, Matthias; Dunens, Alexandra; Schoenitz, Martin; Kuschnerow, Jan C; Kunick, Conrad; Scholl, Stephan

2018-05-01

Finding and optimising of synthesis processes for active pharmaceutical ingredients (API) is time consuming. In the finding phase, established methods for synthesis, purification and formulation are used to achieve a high purity API for biological studies. For promising API candidates, this is followed by pre-clinical and clinical studies requiring sufficient quantities of the active component. Ideally, these should be produced with a process representative for a later production process and suitable for scaling to production capacity. This work presents an overview of different approaches for process synthesis based on an existing lab protocol. This is demonstrated for the production of the model drug 4,5,6,7-tetrabromo-2-(1H-imidazol-2-yl) isoindolin-1,3-dione (TBID). Early batch synthesis and purification procedures typically suffer from low and fluctuating yields and purities due to poor process control. In a first step the literature synthesis and purification procedure was modified and optimized using solubility measurements, targeting easier and safer processing for consecutive studies. Copyright © 2018 Elsevier B.V. All rights reserved.

Adaptive process control using fuzzy logic and genetic algorithms

NASA Technical Reports Server (NTRS)

Karr, C. L.

1993-01-01

Researchers at the U.S. Bureau of Mines have developed adaptive process control systems in which genetic algorithms (GA's) are used to augment fuzzy logic controllers (FLC's). GA's are search algorithms that rapidly locate near-optimum solutions to a wide spectrum of problems by modeling the search procedures of natural genetics. FLC's are rule based systems that efficiently manipulate a problem environment by modeling the 'rule-of-thumb' strategy used in human decision making. Together, GA's and FLC's possess the capabilities necessary to produce powerful, efficient, and robust adaptive control systems. To perform efficiently, such control systems require a control element to manipulate the problem environment, and a learning element to adjust to the changes in the problem environment. Details of an overall adaptive control system are discussed. A specific laboratory acid-base pH system is used to demonstrate the ideas presented.

Adaptive Process Control with Fuzzy Logic and Genetic Algorithms

NASA Technical Reports Server (NTRS)

Karr, C. L.

1993-01-01

Researchers at the U.S. Bureau of Mines have developed adaptive process control systems in which genetic algorithms (GA's) are used to augment fuzzy logic controllers (FLC's). GA's are search algorithms that rapidly locate near-optimum solutions to a wide spectrum of problems by modeling the search procedures of natural genetics. FLC's are rule based systems that efficiently manipulate a problem environment by modeling the 'rule-of-thumb' strategy used in human decision-making. Together, GA's and FLC's possess the capabilities necessary to produce powerful, efficient, and robust adaptive control systems. To perform efficiently, such control systems require a control element to manipulate the problem environment, an analysis element to recognize changes in the problem environment, and a learning element to adjust to the changes in the problem environment. Details of an overall adaptive control system are discussed. A specific laboratory acid-base pH system is used to demonstrate the ideas presented.

Innovations in coating technology.

PubMed

Behzadi, Sharareh S; Toegel, Stefan; Viernstein, Helmut

2008-01-01

Despite representing one of the oldest pharmaceutical techniques, coating of dosage forms is still frequently used in pharmaceutical manufacturing. The aims of coating range from simply masking the taste or odour of drugs to the sophisticated controlling of site and rate of drug release. The high expectations for different coating technologies have required great efforts regarding the development of reproducible and controllable production processes. Basically, improvements in coating methods have focused on particle movement, spraying systems, and air and energy transport. Thereby, homogeneous distribution of coating material and increased drying efficiency should be accomplished in order to achieve high end product quality. Moreover, given the claim of the FDA to design the end product quality already during the manufacturing process (Quality by Design), the development of analytical methods for the analysis, management and control of coating processes has attracted special attention during recent years. The present review focuses on recent patents claiming improvements in pharmaceutical coating technology and intends to first familiarize the reader with the available procedures and to subsequently explain the application of different analytical tools. Aiming to structure this comprehensive field, coating technologies are primarily divided into pan and fluidized bed coating methods. Regarding pan coating procedures, pans rotating around inclined, horizontal and vertical axes are reviewed separately. On the other hand, fluidized bed technologies are subdivided into those involving fluidized and spouted beds. Then, continuous processing techniques and improvements in spraying systems are discussed in dedicated chapters. Finally, currently used analytical methods for the understanding and management of coating processes are reviewed in detail in the last section of the review.

Training working memory in older adults: Is there an advantage of using strategies?

PubMed

Borella, Erika; Carretti, Barbara; Sciore, Roberta; Capotosto, Emanuela; Taconnat, Laurence; Cornoldi, Cesare; De Beni, Rossana

2017-03-01

The purpose of the present study was to test the efficacy of a working memory (WM) training in elderly people, and to compare the effects of a WM training based on an adaptive procedure with one combining the same procedure with the use of a strategy, based on the construction of visual mental images. Eighteen older adults received training with a WM task (the WM group), another 18 received the same WM training and were also taught to use a visual imagery strategy (the WM + Strategy group), and another 18 served as active controls. Training-related gains in the WM (criterion) task and transfer effects on measures of verbal and visuospatial WM, short-term memory (STM), processing speed, and reasoning were considered. Training gains and transfer effects were also assessed after 6 months. After the training, both the trained groups performed better than the control group in the WM criterion task, and maintained these gains 6 months later; they also showed immediate transfer effects on processing speed. The two trained groups also outperformed the control group in the long term in the WM tasks, in one of the STM tasks (backward span task), and in the processing speed measure. Long-term large effect sizes were found for all the tasks involving memory processes in the WM + Strategy group, but only for the processing speed task in the WM group. Findings are discussed in terms of the benefits and limits of teaching older people a strategy in combination with an adaptive WM training. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Critical Drivers for Safety Culture: Examining Department of Energy and U.S. Army Operational Experiences - 12382

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowes, Elizabeth A.

2012-07-01

Evaluating operational incidents can provide a window into the drivers most critical to establishing and maintaining a strong safety culture, thereby minimizing the potential project risk associated with safety incidents. By examining U.S. Department of Energy (DOE) versus U.S. Army drivers in terms of regulatory and contract requirements, programs implemented to address the requirements, and example case studies of operational events, a view of the elements most critical to making a positive influence on safety culture is presented. Four case studies are used in this evaluation; two from DOE and two from U.S. Army experiences. Although the standards guiding operationsmore » at these facilities are different, there are many similarities in the level of hazards, as well as the causes and the potential consequences of the events presented. Two of the incidents examined, one from a DOE operation and the other from a U.S. Army facility, resulted in workers receiving chemical burns. The remaining two incidents are similar in that significant conduct of operations failures occurred resulting in high-level radioactive waste (in the case of the DOE facility) or chemical agent (in the case of the Army facility) being transferred outside of engineering controls. A review of the investigation reports for all four events indicates the primary causes to be failures in work planning leading to ineffective hazard evaluation and control, lack of procedure adherence, and most importantly, lack of management oversight to effectively reinforce expectations for safe work planning and execution. DOE and Army safety programs are similar, and although there are some differences in contractual requirements, the expectations for safe performance are essentially the same. This analysis concludes that instilling a positive safety culture comes down to management leadership and engagement to (1) cultivate an environment that values a questioning attitude and (2) continually reinforce expectations for the appropriate level of rigor in work planning and procedure adherence. A review of the root causes and key contributing causes to the events indicate: - Three of the four root cause analyses cite lack of management engagement (oversight, involvement, ability to recognize issues, etc.) as a root cause to the events. - Two of the four root cause analyses cite work planning failures as a root cause to the events and all cause analyses reflect work planning failures as contributing factors to the events. - All events with the exception of the Tuba City plant shutdown indicate procedure noncompliance as a key contributor; in the case of Tuba City the procedure issues were primarily related to a lack of procedures, or a lack of sufficiently detailed procedures. - All events included discussion or suggestion of a lack of a questioning attitude, either on the part of management/supervision, work planners, or workers. This analysis suggests that the most critical drivers to safety culture are: - Management engagement, - Effective work planning and procedures, and - Procedure adherence with a questioning attitude to ensure procedural problems are identified and fixed. In high-hazard operational environments the importance of robust work planning processes and procedure adherence cannot be overstated. However, having the processes by themselves is not enough. Management must actively engage in expectation setting and ensure work planning that meets expectations for hazard analysis and control, develop a culture that encourages incident reporting and a questioning attitude, and routinely observe work performance to reinforce expectations for adherence to procedures/work control documents. In conclusion, the most critical driver to achieving a workforce culture that supports safe and effective project performance can be summarized as follows: 'Management engagement to continually reinforce expectations for work planning processes and procedure adherence in an environment that cultivates a questioning attitude'. (authors)« less

Automating PACS quality control with the Vanderbilt image processing enterprise resource

NASA Astrophysics Data System (ADS)

Esparza, Michael L.; Welch, E. Brian; Landman, Bennett A.

2012-02-01

Precise image acquisition is an integral part of modern patient care and medical imaging research. Periodic quality control using standardized protocols and phantoms ensures that scanners are operating according to specifications, yet such procedures do not ensure that individual datasets are free from corruption; for example due to patient motion, transient interference, or physiological variability. If unacceptable artifacts are noticed during scanning, a technologist can repeat a procedure. Yet, substantial delays may be incurred if a problematic scan is not noticed until a radiologist reads the scans or an automated algorithm fails. Given scores of slices in typical three-dimensional scans and widevariety of potential use cases, a technologist cannot practically be expected inspect all images. In large-scale research, automated pipeline systems have had great success in achieving high throughput. However, clinical and institutional workflows are largely based on DICOM and PACS technologies; these systems are not readily compatible with research systems due to security and privacy restrictions. Hence, quantitative quality control has been relegated to individual investigators and too often neglected. Herein, we propose a scalable system, the Vanderbilt Image Processing Enterprise Resource (VIPER) to integrate modular quality control and image analysis routines with a standard PACS configuration. This server unifies image processing routines across an institutional level and provides a simple interface so that investigators can collaborate to deploy new analysis technologies. VIPER integrates with high performance computing environments has successfully analyzed all standard scans from our institutional research center over the course of the last 18 months.

Predictors of Arterial Blood Pressure Control During Deliberate Hypotension with Sodium Nitroprusside in Children

PubMed Central

Spielberg, David R; Barrett, Jeffrey S; Hammer, Gregory B; Drover, David R; Reece, Tammy; Cohane, Carol A; Schulman, Scott R

2014-01-01

Background Sodium nitroprusside (SNP) is used to decrease arterial blood pressure (BP) during certain surgical procedures. There are limited data regarding efficacy of BP control with SNP. There are no data on patient and clinician factors that affect BP control. We evaluated the dose-response relationship of SNP in infants and children undergoing major surgery and performed a quantitative assessment of BP control. Methods One hundred fifty-three subjects at 7 sites received a blinded infusion followed by open-label SNP during operative procedures requiring controlled hypotension. SNP was administered by continuous infusion and titrated to maintain BP control (mean arterial BP [MAP] within ±10% of clinician-defined target). BP was recorded using an arterial catheter. Statistical Process Control methodology was used to quantify BP control. A multivariable model assessed the effects of patient and procedural factors. Results BP was controlled an average 45.4% (SD 23.9%, 95% CI 41.5%-49.18%) of the time. Larger changes in infusion rate were associated with worse BP control (7.99% less control for 1 mcg•kg−•min− increase in average titration size, p=0.0009). A larger difference between a patient's baseline and target MAP predicted worse BP control (0.93% worse control per 1 mmHg increase in MAP difference, p=0.0013). Both effects persisted in multivariable models. Conclusions : SNP was effective in reducing BP. However, BP was within the target range less than half of the time. No clinician or patient factors were predictive of BP control, although two inverse relationships were identified. These relationships require additional study and may be best coupled with exposure-response modeling to propose improved dosing strategies when using SNP for controlled hypotension in the pediatric population. PMID:25099924

Predictors of arterial blood pressure control during deliberate hypotension with sodium nitroprusside in children.

PubMed

Spielberg, David R; Barrett, Jeffrey S; Hammer, Gregory B; Drover, David R; Reece, Tammy; Cohane, Carol A; Schulman, Scott R

2014-10-01

Sodium nitroprusside (SNP) is used to decrease arterial blood pressure (BP) during certain surgical procedures. There are limited data regarding efficacy of BP control with SNP. There are no data on patient and clinician factors that affect BP control. We evaluated the dose-response relationship of SNP in infants and children undergoing major surgery and performed a quantitative assessment of BP control. One hundred fifty-three subjects at 7 sites received a blinded infusion followed by open-label SNP during operative procedures requiring controlled hypotension. SNP was administered by continuous infusion and titrated to maintain BP control (mean arterial BP [MAP] within ±10% of clinician-defined target). BP was recorded using an arterial catheter. Statistical process control methodology was used to quantify BP control. A multivariable model assessed the effects of patient and procedural factors. BP was controlled an average 45.4% (SD 23.9%; 95% CI, 41.5%-49.18%) of the time. Larger changes in infusion rate were associated with worse BP control (7.99% less control for 1 μg·kg·min increase in average titration size, P = 0.0009). A larger difference between a patient's baseline and target MAP predicted worse BP control (0.93% worse control per 1-mm Hg increase in MAP difference, P = 0.0013). Both effects persisted in multivariable models. SNP was effective in reducing BP. However, BP was within the target range less than half of the time. No clinician or patient factors were predictive of BP control, although 2 inverse relationships were identified. These relationships require additional study and may be best coupled with exposure-response modeling to propose improved dosing strategies when using SNP for controlled hypotension in the pediatric population.

Geometric error characterization and error budgets. [thematic mapper

NASA Technical Reports Server (NTRS)

Beyer, E.

1982-01-01

Procedures used in characterizing geometric error sources for a spaceborne imaging system are described using the LANDSAT D thematic mapper ground segment processing as the prototype. Software was tested through simulation and is undergoing tests with the operational hardware as part of the prelaunch system evaluation. Geometric accuracy specifications, geometric correction, and control point processing are discussed. Cross track and along track errors are tabulated for the thematic mapper, the spacecraft, and ground processing to show the temporal registration error budget in pixel (42.5 microrad) 90%.

Quality control of the tribological coating PS212

NASA Technical Reports Server (NTRS)

Sliney, Harold E.; Dellacorte, Christopher; Deadmore, Daniel L.

1989-01-01

PS212 is a self-lubricating, composite coating that is applied by the plasma spray process. It is a functional lubricating coating from 25 C (or lower) to 900 C. The coating is prepared from a blend of three different powders with very dissimilar properties. Therefore, the final chemical composition and lubricating effectiveness of the coatings are very sensitive to the process variables used in their preparation. Defined here are the relevant variables. The process and analytical procedures that will result in satisfactory tribological coatings are discussed.

[Prospects in getting accordance between chemical analytic control means and medical technical requirements to safety system concerning chemical weapons destruction].

PubMed

Rembovskiĭ, V R; Mogilenkova, L A; Savel'eva, E I

2005-01-01

The major unit monitoring chemical weapons destruction objects is a system of chemical analyticcontrol over the technologic process procedures and possibility of environment and workplace pollution withtoxicchemicals and their destruction products. At the same time, physical and chemical control means meet sanitary and hygienic requirements incompletely. To provide efficient control, internationally recognized approaches should be adapted to features of Russian system monitoring pollution of chemical weapons destruction objects with toxic chemicals.

A Human-Centered Command and Control (C2) Assessment of an Experimental Campaign Planning Tool

DTIC Science & Technology

2014-04-01

and control (team without the CPT) groups . The two groups were designed to have an equal number of members; however, one member of the experimental...the researchers to analyze the planning process and outcomes. 3.3 Design and Procedure An experimental versus control group design was implemented...the post -PFnet (figure 16b). Within the PFnets, a concept can be focused on in order to identify how the individual or group is defining or

Security Implications of OPC, OLE, DCOM, and RPC in Control Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2006-01-01

OPC is a collection of software programming standards and interfaces used in the process control industry. It is intended to provide open connectivity and vendor equipment interoperability. The use of OPC technology simplifies the development of control systems that integrate components from multiple vendors and support multiple control protocols. OPC-compliant products are available from most control system vendors, and are widely used in the process control industry. OPC was originally known as OLE for Process Control; the first standards for OPC were based on underlying services in the Microsoft Windows computing environment. These underlying services (OLE [Object Linking and Embedding],more » DCOM [Distributed Component Object Model], and RPC [Remote Procedure Call]) have been the source of many severe security vulnerabilities. It is not feasible to automatically apply vendor patches and service packs to mitigate these vulnerabilities in a control systems environment. Control systems using the original OPC data access technology can thus inherit the vulnerabilities associated with these services. Current OPC standardization efforts are moving away from the original focus on Microsoft protocols, with a distinct trend toward web-based protocols that are independent of any particular operating system. However, the installed base of OPC equipment consists mainly of legacy implementations of the OLE for Process Control protocols.« less

Quality control by HyperSpectral Imaging (HSI) in solid waste recycling: logics, algorithms and procedures

NASA Astrophysics Data System (ADS)

Bonifazi, Giuseppe; Serranti, Silvia

2014-03-01

In secondary raw materials and recycling sectors, the products quality represents, more and more, the key issue to pursuit in order to be competitive in a more and more demanding market, where quality standards and products certification play a preheminent role. These goals assume particular importance when recycling actions are applied. Recovered products, resulting from waste materials, and/or dismissed products processing, are, in fact, always seen with a certain suspect. An adequate response of the industry to the market can only be given through the utilization of equipment and procedures ensuring pure, high-quality production, and efficient work and cost. All these goals can be reached adopting not only more efficient equipment and layouts, but also introducing new processing logics able to realize a full control of the handled material flow streams fulfilling, at the same time, i) an easy management of the procedures, ii) an efficient use of the energy, iii) the definition and set up of reliable and robust procedures, iv) the possibility to implement network connectivity capabilities finalized to a remote monitoring and control of the processes and v) a full data storage, analysis and retrieving. Furthermore the ongoing legislation and regulation require the implementation of recycling infrastructure characterised by high resources efficiency and low environmental impacts, both aspects being strongly linked to the waste materials and/or dismissed products original characteristics. For these reasons an optimal recycling infrastructure design primarily requires a full knowledge of the characteristics of the input waste. What previously outlined requires the introduction of a new important concept to apply in solid waste recycling, the recycling-oriented characterization, that is the set of actions addressed to strategically determine selected attributes, in order to get goaloriented data on waste for the development, implementation or improvement of recycling strategies. The problems arising when suitable HyperSpectral Imaging (HSI) based procedures have to be developed and implemented to solid waste products characterization, in order to define time efficient compression and interpretation techniques, are thus analyzed and discussed in the following. Particular attention was also addressed to define an integrated hardware and software (HW and SW) platform able to perform a non-intrusive, non-contact and real-time analysis and embedding a core of analytical logics and procedures to utilize both at laboratory and industrial scale. Several case studies, referred to waste plastics products, are presented and discussed.

Sequential continuous flow processes for the oxidation of amines and azides by using HOF·MeCN.

PubMed

McPake, Christopher B; Murray, Christopher B; Sandford, Graham

2012-02-13

The generation and use of the highly potent oxidising agent HOF·MeCN in a controlled single continuous flow process is described. Oxidations of amines and azides to corresponding nitrated systems by using fluorine gas, water and acetonitrile by sequential gas-liquid/liquid-liquid continuous flow procedures are reported. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Subgrouping Chronic Fatigue Syndrome Patients By Genetic and Immune Profiling

DTIC Science & Technology

2015-12-01

participant inclusion was also verified against our master demographic file. This process revealed that only a small percentage of participants (...the ! ! − !!! , ∈ ℤ!| ≤ 7 , is a cubic -spline basis on three knots, ! is value of outcome for batch control, and is residual ...tests. Specifically, -value adjustments will employ an 8 adaptive two- stage linear step-up procedure to control the FDR at 5% (Benjamani et al. 2006

Microelectronics Failure Analysis Techniques. A Procedural Guide

DTIC Science & Technology

1980-01-01

Process Control ." Scanning Electron Microscopy/1976, lIT Research Institute, Chicago, Illinois, April 1976, pp. 515-519. 49. Cunningham, R.F. "Sample...Character- ization and Quality Control ." Scanning Electron Microscopy/1977 vol. I, lIT Research Institute, Chicago, Illinois, March 1977, pp. 201-210. 151...reference purposes. Neither the United States Government, the General Electric Company nor the lIT Research Institute warrant the accuracy of this

[Microbiological assessment of the Gouda-type cheese-making process in a Venezuelan industry].

PubMed

Dáivila, Jacqueline; Reyes, Genara; Corzo, Otoniel

2006-03-01

The adoption of the Hazard Analysis and Critical Control Point (HACCP) system is necessary to assure the safety of the product in the cheese-making industry. The compliment of pre-requisite programs as Good Manufacture Practices (GMPs) and Sanitation Standard Operating Procedures (SSOPs) are required before the implementation of the HACCP plan. GMPs are the standards related to equipments, tools, personnel, etc. SSOPs are the procedures related to hygiene and sanitation of the plant and workers. The aim of this study was to assess the compliment of the pre-requisite programs and the microbiological conditions of the Gouda type cheese-making process in a Venezuelan processing plant before designing a HACCP plan. Samples were: (a) raw milk, pasteurized milk, curd and ripened cheese, (b) water, (c) environment of the production areas and ripening premises, (d) equipments before and after sanitation, (e) food handlers. Microbiological analyses were done according to COVENIN standards. This study showed that even though pasteurization process was effective to kill pathogen bacteria of the raw milk and the water was safe, however there are deficient manufacture practices in the hygiene as well as in sanitation of the plant and food handlers. Prerequisite programs (GMP-SSOP) of this industry need to be well established, controlled and evaluated.

Dynamic Engagement of Cognitive Control Modulates Recovery From Misinterpretation During Real-Time Language Processing.

PubMed

Hsu, Nina S; Novick, Jared M

2016-04-01

Speech unfolds swiftly, yet listeners keep pace by rapidly assigning meaning to what they hear. Sometimes, though, initial interpretations turn out to be wrong. How do listeners revise misinterpretations of language input moment by moment to avoid comprehension errors? Cognitive control may play a role by detecting when processing has gone awry and then initiating behavioral adjustments accordingly. However, no research to date has investigated a cause-and-effect interplay between cognitive-control engagement and the overriding of erroneous interpretations in real time. Using a novel cross-task paradigm, we showed that Stroop-conflict detection, which mobilizes cognitive-control procedures, subsequently facilitates listeners' incremental processing of temporarily ambiguous spoken instructions that induce brief misinterpretation. When instructions followed incongruent Stroop items, compared with congruent Stroop items, listeners' eye movements to objects in a scene reflected more transient consideration of the false interpretation and earlier recovery of the correct one. Comprehension errors also decreased. Cognitive-control engagement therefore accelerates sentence-reinterpretation processes, even as linguistic input is still unfolding. © The Author(s) 2016.

Instrumentation & Data Acquisition System (D AS) Engineer

NASA Technical Reports Server (NTRS)

Jackson, Markus Deon

2015-01-01

The primary job of an Instrumentation and Data Acquisition System (DAS) Engineer is to properly measure physical phenomenon of hardware using appropriate instrumentation and DAS equipment designed to record data during a specified test of the hardware. A DAS system includes a CPU or processor, a data storage device such as a hard drive, a data communication bus such as Universal Serial Bus, software to control the DAS system processes like calibrations, recording of data and processing of data. It also includes signal conditioning amplifiers, and certain sensors for specified measurements. My internship responsibilities have included testing and adjusting Pacific Instruments Model 9355 signal conditioning amplifiers, writing and performing checkout procedures, writing and performing calibration procedures while learning the basics of instrumentation.

A novel method for fabrication of continuous-relief optical elements

NASA Astrophysics Data System (ADS)

Guo, Xiaowei; Du, Jinglei; Chen, Mingyong; Ma, Yanqin; Zhu, Jianhua; Peng, Qinjun; Guo, Yongkang; Du, Chunlei

2005-08-01

A novel method for the fabrication of continuous micro-optical components is presented in this paper. It employs a computer controlled spatial-light-modulator (SLM) as a switchable projection mask and silver-halide sensitized gelatin (SHSG) as recording material. By etching SHSG with enzyme solution, the micro-optical components with relief modulation can be generated through special processing procedures. The principles of digital SLM-based lithography and enzyme etching SHSG are discussed in detail, and microlens arrays, micro axicon-lens arrays and gratings with good profile were achieved. This method is simple, cheap and the aberration in processing procedures can be in-situ corrected in the step of designing mask, so it is a practical method to fabricate continuous profile for low-volume production.

System status display evaluation

NASA Technical Reports Server (NTRS)

Summers, Leland G.

1988-01-01

The System Status Display is an electronic display system which provides the crew with an enhanced capability for monitoring and managing the aircraft systems. A flight simulation in a fixed base cockpit simulator was used to evaluate alternative design concepts for this display system. The alternative concepts included pictorial versus alphanumeric text formats, multifunction versus dedicated controls, and integration of the procedures with the system status information versus paper checklists. Twelve pilots manually flew approach patterns with the different concepts. System malfunctions occurred which required the pilots to respond to the alert by reconfiguring the system. The pictorial display, the multifunction control interfaces collocated with the system display, and the procedures integrated with the status information all had shorter event processing times and lower subjective workloads.

Parameter learning for performance adaptation

NASA Technical Reports Server (NTRS)

Peek, Mark D.; Antsaklis, Panos J.

1990-01-01

A parameter learning method is introduced and used to broaden the region of operability of the adaptive control system of a flexible space antenna. The learning system guides the selection of control parameters in a process leading to optimal system performance. A grid search procedure is used to estimate an initial set of parameter values. The optimization search procedure uses a variation of the Hooke and Jeeves multidimensional search algorithm. The method is applicable to any system where performance depends on a number of adjustable parameters. A mathematical model is not necessary, as the learning system can be used whenever the performance can be measured via simulation or experiment. The results of two experiments, the transient regulation and the command following experiment, are presented.

Dimming LEDs with Phase-Cut Dimmers: The Specifier's Process for Maximizing Success

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, Naomi J.; Poplawski, Michael E.

2013-10-01

This report reviews how phase-cut dimmers work, how LEDs differ from the incandescent lamps that the dimmers were historically designed to control, and how these differences can lead to complications when trying to dim LEDs. Compatibility between a specific LED source and a specific phase-cut dimmer is often unknown and difficult to assess, and ensuring compatibility adds complexity to the design, specification, bidding, and construction observation phases for new buildings and major remodel projects. To maximize project success, this report provides both general guidance and step-by-step procedures for designing phase-controlled LED dimming on both new and existing projects, as wellmore » as real-world examples of how to use those procedures.« less

Reverberation Chamber Uniformity Validation and Radiated Susceptibility Test Procedures for the NASA High Intensity Radiated Fields Laboratory

NASA Technical Reports Server (NTRS)

Koppen, Sandra V.; Nguyen, Truong X.; Mielnik, John J.

2010-01-01

The NASA Langley Research Center's High Intensity Radiated Fields Laboratory has developed a capability based on the RTCA/DO-160F Section 20 guidelines for radiated electromagnetic susceptibility testing in reverberation chambers. Phase 1 of the test procedure utilizes mode-tuned stirrer techniques and E-field probe measurements to validate chamber uniformity, determines chamber loading effects, and defines a radiated susceptibility test process. The test procedure is segmented into numbered operations that are largely software controlled. This document is intended as a laboratory test reference and includes diagrams of test setups, equipment lists, as well as test results and analysis. Phase 2 of development is discussed.

40 CFR 725.50 - EPA review.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false EPA review. 725.50 Section 725.50... REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Administrative Procedures § 725.50 EPA review. (a) MCANs... Document Control Officer receives a complete submission, or the date EPA determines the submission is...

40 CFR 725.50 - EPA review.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false EPA review. 725.50 Section 725.50... REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Administrative Procedures § 725.50 EPA review. (a) MCANs... Document Control Officer receives a complete submission, or the date EPA determines the submission is...

40 CFR 725.50 - EPA review.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false EPA review. 725.50 Section 725.50... REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Administrative Procedures § 725.50 EPA review. (a) MCANs... Document Control Officer receives a complete submission, or the date EPA determines the submission is...

40 CFR 725.50 - EPA review.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false EPA review. 725.50 Section 725.50... REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Administrative Procedures § 725.50 EPA review. (a) MCANs... Document Control Officer receives a complete submission, or the date EPA determines the submission is...

40 CFR 725.50 - EPA review.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false EPA review. 725.50 Section 725.50... REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Administrative Procedures § 725.50 EPA review. (a) MCANs... Document Control Officer receives a complete submission, or the date EPA determines the submission is...

12 CFR 347.119 - Specific consent.

Code of Federal Regulations, 2010 CFR

2010-01-01

... processing procedure. (d) Specific consent. Direct or indirect investments in or activities of foreign... control such organization as a result of a foreign investment; or (ii) A bank would be establishing a... foreign country. (1) Applicable law or practice in the foreign country where the foreign organization or...

40 CFR 725.36 - New information.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false New information. 725.36 Section 725.36... REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Administrative Procedures § 725.36 New information. (a) During the review period, if a submitter possesses, controls, or knows of new information that materially...

40 CFR 63.116 - Process vent provisions-performance test methods and procedures to determine compliance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... reduce the vent stream halogen atom mass emission rate to less than 0.45 kilogram per hour prior to a combustion control device in compliance with § 63.113(c)(2) of this subpart shall determine the halogen atom...

40 CFR 63.116 - Process vent provisions-performance test methods and procedures to determine compliance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... reduce the vent stream halogen atom mass emission rate to less than 0.45 kilogram per hour prior to a combustion control device in compliance with § 63.113(c)(2) of this subpart shall determine the halogen atom...

40 CFR 63.116 - Process vent provisions-performance test methods and procedures to determine compliance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... reduce the vent stream halogen atom mass emission rate to less than 0.45 kilogram per hour prior to a combustion control device in compliance with § 63.113(c)(2) of this subpart shall determine the halogen atom...

40 CFR 63.116 - Process vent provisions-performance test methods and procedures to determine compliance.

Code of Federal Regulations, 2012 CFR

2012-07-01

... reduce the vent stream halogen atom mass emission rate to less than 0.45 kilogram per hour prior to a combustion control device in compliance with § 63.113(c)(2) of this subpart shall determine the halogen atom...

75 FR 2488 - Mid-Atlantic Fishery Management Council; Public Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-15

... Mid-Atlantic Fishery Management Council's (MAFMC) Scientific and Statistical Committee (SSC) will hold... include new member orientation (overview of Council process and role of the SSC), review and adoption of SSC Standard Operating Practices and Procedures, ABC Control Rule Framework and Council Risk Policy...

Salivary Gland Secretion.

ERIC Educational Resources Information Center

Dorman, H. L.; And Others

1981-01-01

Describes materials and procedures for an experiment utilizing a live dog to demonstrate: (1) physiology of the salivary gland; (2) parasympathetic control of the salivary gland; (3) influence of varying salivary flow rates on sodium and potassium ions, osmolarity and pH; and (4) salivary secretion as an active process. (DS)

40 CFR 86.1825-01 - Durability demonstration procedures for refueling emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... life. The manufacturer shall use good engineering judgment in determining this process. (a) Service... full useful life. The manufacturer shall use good engineering judgement in developing this method. (2... accumulation programs, all emission control components and systems (including both hardware and software) must...

40 CFR 86.1825-01 - Durability demonstration procedures for refueling emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... life. The manufacturer shall use good engineering judgment in determining this process. (a) Service... full useful life. The manufacturer shall use good engineering judgement in developing this method. (2... accumulation programs, all emission control components and systems (including both hardware and software) must...

40 CFR 86.1825-01 - Durability demonstration procedures for refueling emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... life. The manufacturer shall use good engineering judgment in determining this process. (a) Service... full useful life. The manufacturer shall use good engineering judgement in developing this method. (2... accumulation programs, all emission control components and systems (including both hardware and software) must...

Safer Soldering Guidelines and Instructional Resources

ERIC Educational Resources Information Center

Love, Tyler S.; Tomlinson, Joel

2018-01-01

Soldering is a useful and necessary process for many classroom, makerspace, Fab Lab, technology and engineering lab, and science lab activities. As described in this article, soldering can pose many safety risks without proper engineering controls, standard operating procedures, and direct instructor supervision. There are many safety hazards…

Thalamic volume deficit contributes to procedural and explicit memory impairment in HIV infection with primary alcoholism comorbidity.

PubMed

Fama, Rosemary; Rosenbloom, Margaret J; Sassoon, Stephanie A; Rohlfing, Torsten; Pfefferbaum, Adolf; Sullivan, Edith V

2014-12-01

Component cognitive and motor processes contributing to diminished visuomotor procedural learning in HIV infection with comorbid chronic alcoholism (HIV+ALC) include problems with attention and explicit memory processes. The neural correlates associated with this constellation of cognitive and motor processes in HIV infection and alcoholism have yet to be delineated. Frontostriatal regions are affected in HIV infection, frontothalamocerebellar regions are affected in chronic alcoholism, and frontolimbic regions are likely affected in both; all three of these systems have the potential of contributing to both visuomotor procedural learning and explicit memory processes. Here, we examined the neural correlates of implicit memory, explicit memory, attention, and motor tests in 26 HIV+ALC (5 with comorbidity for nonalcohol drug abuse/dependence) and 19 age-range matched healthy control men. Parcellated brain volumes, including cortical, subcortical, and allocortical regions, as well as cortical sulci and ventricles, were derived using the SRI24 brain atlas. Results indicated that smaller thalamic volumes were associated with poorer performance on tests of explicit (immediate and delayed) and implicit (visuomotor procedural) memory in HIV+ALC. By contrast, smaller hippocampal volumes were associated with lower scores on explicit, but not implicit memory. Multiple regression analyses revealed that volumes of both the thalamus and the hippocampus were each unique independent predictors of explicit memory scores. This study provides evidence of a dissociation between implicit and explicit memory tasks in HIV+ALC, with selective relationships observed between hippocampal volume and explicit but not implicit memory, and highlights the relevance of the thalamus to mnemonic processes.

Antenna Linear-Quadratic-Gaussian (LQG) Ccontrollers: Properties, Limits of Performance, and Tuning

NASA Technical Reports Server (NTRS)

Gawronski, Wodek K.

2004-01-01

The LQG controllers significantly improve antenna tracking precision, but their tuning is a trial-and-error process. A control engineer has two tools to tune an LQG controller: the choice of coordinate system of the controller, and the selection of weights of the LQG performance index. The paper selects the coordinates of the open-loop model that simplify the shaping of the closed-loop performance. and analyzes the impact of thc weights on the antenna closed-loop bandwidth, disturbance rejection properties, and antenna acceleration. Finally, it presents the LQG controller tuning procedure that rationally shapes the closed-loop performance.

Nano-lead particle synthesis from waste cathode ray-tube funnel glass.

PubMed

Xing, Mingfei; Zhang, Fu-Shen

2011-10-30

Waste cathode ray-tube (CRT) funnel glass is classified as hazardous waste since it contains high amount of lead. In the present study, a novel process for lead nanopowder synthesis from this type of glass was developed by combining vacuum carbon-thermal reduction and inert-gas consolidation procedures. The key trait of the process was to evaporate lead out of the glass to obtain harmless glass powder and synchronously produce lead nanoparticles. In the synthesis process, lead oxide in the funnel glass was firstly reduced to elemental lead, and evaporated rapidly in vacuum circumstance, then quenched and formed nano-size particles on the surface of the cooling device. Experimental results showed that temperature, pressure and argon gas flow rate were the major parameters controlling lead evaporation ratio and the morphology of lead nanoparticles. The maximum lead evaporation ratio was 96.8% and particles of 4-34 nm were successfully obtained by controlling the temperature, holding time, process pressure, argon gas flow rate at 1000°C, 2-4h, 500-2000 Pa, 50-200 ml/min, respectively. Toxicity characteristic leaching procedure (TCLP) results showed that lead leaching from the residue glass met the USEPA threshold. Accordingly, this study developed a practical and environmental-friendly process for detoxification and reclamation of waste lead-containing glass. Copyright © 2011 Elsevier B.V. All rights reserved.

Potato Operation: automatic detection of potato diseases

NASA Astrophysics Data System (ADS)

Lefebvre, Marc; Zimmerman, Thierry; Baur, Charles; Guegerli, Paul; Pun, Thierry

1995-01-01

The Potato Operation is a collaborative, multidisciplinary project in the domain of destructive testing of agricultural products. It aims at automatizing pulp sampling of potatoes in order to detect possible viral diseases. Such viruses can decrease fields productivity by a factor of up to ten. A machine, composed of three conveyor belts, a vision system, a robotic arm and controlled by a PC has been built. Potatoes are brought one by one from a bulk to the vision system, where they are seized by a rotating holding device. The sprouts, where the viral activity is maximum, are then detected by an active vision process operating on multiple views. The 3D coordinates of the sampling point are communicated to the robot arm holding a drill. Some flesh is then sampled by the drill, then deposited into an Elisa plate. After sampling, the robot arm washes the drill in order to prevent any contamination. The PC computer simultaneously controls these processes, the conveying of the potatoes, the vision algorithms and the sampling procedure. The master process, that is the vision procedure, makes use of three methods to achieve the sprouts detection. A profile analysis first locates the sprouts as protuberances. Two frontal analyses, respectively based on fluorescence and local variance, confirm the previous detection and provide the 3D coordinate of the sampling zone. The other two processes work by interruption of the master process.

Radiation dosimetry for quality control of food preservation and disinfestation

NASA Astrophysics Data System (ADS)

McLaughlin, W. L.; Miller, A.; Uribe, R. M.

In the use of x and gamma rays and scanned electron beams to extend the shelf life of food by delay of sprouting and ripening, killing of microbes, and control of insect population, quality assurance is provided by standardized radiation dosimetry. By strategic placement of calibrated dosimeters that are sufficiently stable and reproducible, it is possible to monitor minimum and maximum radiation absorbed dose levels and dose uniformity for a given processed foodstuff. The dosimetry procedure is especially important in the commisioning of a process and in making adjustments of process parameters (e.g. conveyor speed) to meet changes that occur in product and source parameters (e.g. bulk density and radiation spectrum). Routine dosimetry methods and certain corrections of dosimetry data may be selected for the radiations used in typical food processes.

PH Tester Gauge Repeatability and Reproducibility Study for WO3 Nanostructure Hydrothermal Growth Process

NASA Astrophysics Data System (ADS)

Abd Rashid, Amirul; Hayati Saad, Nor; Bien Chia Sheng, Daniel; Yee, Lee Wai

2014-06-01

PH value is one of the important variables for tungsten trioxide (WO3) nanostructure hydrothermal synthesis process. The morphology of the synthesized nanostructure can be properly controlled by measuring and controlling the pH value of the solution used in this facile synthesis route. Therefore, it is very crucial to ensure the gauge used for pH measurement is reliable in order to achieve the expected result. In this study, gauge repeatability and reproducibility (GR&R) method was used to assess the repeatability and reproducibility of the pH tester. Based on ANOVA method, the design of experimental metrics as well as the result of the experiment was analyzed using Minitab software. It was found that the initial GR&R value for the tester was at 17.55 % which considered as acceptable. To further improve the GR&R level, a new pH measuring procedure was introduced. With the new procedure, the GR&R value was able to be reduced to 2.05%, which means the tester is statistically very ideal to measure the pH of the solution prepared for WO3 hydrothermal synthesis process.

Flexible Automation System for Determination of Elemental Composition of Incrustations in Clogged Biliary Endoprostheses Using ICP-MS.

PubMed

Fleischer, Heidi; Ramani, Kinjal; Blitti, Koffi; Roddelkopf, Thomas; Warkentin, Mareike; Behrend, Detlef; Thurow, Kerstin

2018-02-01

Automation systems are well established in industries and life science laboratories, especially in bioscreening and high-throughput applications. An increasing demand of automation solutions can be seen in the field of analytical measurement in chemical synthesis, quality control, and medical and pharmaceutical fields, as well as research and development. In this study, an automation solution was developed and optimized for the investigation of new biliary endoprostheses (stents), which should reduce clogging after implantation in the human body. The material inside the stents (incrustations) has to be controlled regularly and under identical conditions. The elemental composition is one criterion to be monitored in stent development. The manual procedure was transferred to an automated process including sample preparation, elemental analysis using inductively coupled plasma mass spectrometry (ICP-MS), and data evaluation. Due to safety issues, microwave-assisted acid digestion was executed outside of the automation system. The performance of the automated process was determined and validated. The measurement results and the processing times were compared for both the manual and the automated procedure. Finally, real samples of stent incrustations and pig bile were analyzed using the automation system.

Mechanical properties of porous and cellular materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sieradzki, K.; Green, D.J.; Gibson, L.J.

1991-01-01

This symposium successfully brought scientists together from a wide variety of disciplines to focus on the mechanical behavior of porous and cellular solids composed of metals, ceramics, polymers, or biological materials. For cellular materials, papers ranged from processing techniques through microstructure-mechanical property relationships to design. In an overview talk, Mike Ashby (Cambridge Univ.) showed how porous cellular materials can be more efficient than dense materials in designs that require minimum weight. He indicated that many biological materials have been able to accomplish such efficiency but there exists an opportunity to design even more efficient, manmade materials controlling microstructures at differentmore » scale levels. In the area of processing, James Aubert (Sandia National Laboratories) discussed techiques for manipulating polymersolvent phase equilibria to control the microstructure of microcellular foams. Other papers on processing discussed the production of cellular ceramics by CVD, HIPing and sol- gel techniques. Papers on the mechanical behavior of cellular materials considered various ceramics microcellular polymers, conventional polymer foams and apples. There were also contributions that considered optimum design procedures for cellular materials. Steven Cowin (City Univ. of New York) discussed procedures to match the discrete microstructural aspects of cellular materials with the continuum mechanics approach to their elastic behavior.« less

Control of the Pore Texture in Nanoporous Silicon via Chemical Dissolution.

PubMed

Secret, Emilie; Wu, Chia-Chen; Chaix, Arnaud; Galarneau, Anne; Gonzalez, Philippe; Cot, Didier; Sailor, Michael J; Jestin, Jacques; Zanotti, Jean-Marc; Cunin, Frédérique; Coasne, Benoit

2015-07-28

The surface and textural properties of porous silicon (pSi) control many of its physical properties essential to its performance in key applications such as optoelectronics, energy storage, luminescence, sensing, and drug delivery. Here, we combine experimental and theoretical tools to demonstrate that the surface roughness at the nanometer scale of pSi can be tuned in a controlled fashion using partial thermal oxidation followed by removal of the resulting silicon oxide layer with hydrofluoric acid (HF) solution. Such a process is shown to smooth the pSi surface by means of nitrogen adsorption, electron microscopy, and small-angle X-ray and neutron scattering. Statistical mechanics Monte Carlo simulations, which are consistent with the experimental data, support the interpretation that the pore surface is initially rough and that the oxidation/oxide removal procedure diminishes the surface roughness while increasing the pore diameter. As a specific example considered in this work, the initial roughness ξ ∼ 3.2 nm of pSi pores having a diameter of 7.6 nm can be decreased to 1.0 nm following the simple procedure above. This study allows envisioning the design of pSi samples with optimal surface properties toward a specific process.

Normal Aging of the Attentional Control Functions That Underlie Working Memory.

PubMed

Sylvain-Roy, Stéphanie; Lungu, Ovidiu; Belleville, Sylvie

2015-09-01

This study assessed the effect of aging on 3 attentional control functions (ACFs)--shifting, inhibition, and updating--and on their contribution to working memory (WM) tasks. Complex WM tasks (the Brown-Peterson procedure, the reading span, and the alpha span) and tasks used to derive composite measures of the ACFs were administered to 75 younger and 75 older adults. Of the 3 ACFs, only inhibition was impaired in aging after controlling for processing speed. Furthermore, the effect of aging on WM tasks was not pervasive, as older adults showed impaired performance on the Brown-Peterson procedure and the reading span but not on the alpha span. When examining the contribution of ACFs to WM in older adults, updating accounted for performance on the Brown-Peterson and reading span tasks, and inhibition was involved in performance on the alpha span task. In younger adults, it was processing speed that contributed the most to WM. This pattern of results suggests that complex WM tasks reflect different ACFs and that this varies as a function of age. © The Author 2014. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Pavlovian autoshaping procedures increase plasma corticosterone and levels of norepinephrine and serotonin in prefrontal cortex in rats.

PubMed

Tomie, Arthur; Tirado, Aidaluz D; Yu, Lung; Pohorecky, Larissa A

2004-08-12

Pavlovian autoshaping procedures provide for pairings of a small object conditioned stimulus (CS) with a rewarding substance unconditioned stimulus (US), resulting in the acquisition of complex sequences of CS-directed skeletal-motor responses or autoshaping conditioned responses (CRs). Autoshaping procedures induce higher post-session levels of corticosterone than in controls receiving CS and US randomly, and the enhanced post-session corticosterone levels have been attributed to the appetitive or arousal-inducing effects of autoshaping procedures. Enhanced corticosterone release can be induced by aversive stimulation or stressful situations, where it is often accompanied by higher levels of norepinephrine (NE) and serotonin (5-HT) in prefrontal cortex (PFC) but not in striatum (ST). Effects of autoshaping procedures on post-session corticosterone levels, NE contents in PFC, and 5-HT contents in PFC and ST were investigated in male Long-Evans rats. Post-session blood samples revealed higher corticosterone levels in the CS-US Paired group (n = 46) than in the CS-US Random control group (n = 21), and brain samples revealed higher levels of PFC NE and 5-HT in CS-US Paired group. Striatal 5-HT levels were unaltered by the autoshaping procedures. Autoshaping procedures provide for appetitive stimulation and induce an arousal-like state, as well as simultaneous stress-like changes in plasma corticosterone and monoamine levels in PFC. Autoshaping, therefore, may be useful for the study of endocrine and central processes associated with appetitive conditions.

The Use of Lean Six Sigma Methodology in Increasing Capacity of a Chemical Production Facility at DSM.

PubMed

Meeuwse, Marco

2018-03-30

Lean Six Sigma is an improvement method, combining Lean, which focuses on removing 'waste' from a process, with Six Sigma, which is a data-driven approach, making use of statistical tools. Traditionally it is used to improve the quality of products (reducing defects), or processes (reducing variability). However, it can also be used as a tool to increase the productivity or capacity of a production plant. The Lean Six Sigma methodology is therefore an important pillar of continuous improvement within DSM. In the example shown here a multistep batch process is improved, by analyzing the duration of the relevant process steps, and optimizing the procedures. Process steps were performed in parallel instead of sequential, and some steps were made shorter. The variability was reduced, giving the opportunity to make a tighter planning, and thereby reducing waiting times. Without any investment in new equipment or technical modifications, the productivity of the plant was improved by more than 20%; only by changing procedures and the programming of the process control system.

Using Six Sigma to reduce medication errors in a home-delivery pharmacy service.

PubMed

Castle, Lon; Franzblau-Isaac, Ellen; Paulsen, Jim

2005-06-01

Medco Health Solutions, Inc. conducted a project to reduce medication errors in its home-delivery service, which is composed of eight prescription-processing pharmacies, three dispensing pharmacies, and six call-center pharmacies. Medco uses the Six Sigma methodology to reduce process variation, establish procedures to monitor the effectiveness of medication safety programs, and determine when these efforts do not achieve performance goals. A team reviewed the processes in home-delivery pharmacy and suggested strategies to improve the data-collection and medication-dispensing practices. A variety of improvement activities were implemented, including a procedure for developing, reviewing, and enhancing sound-alike/look-alike (SALA) alerts and system enhancements to improve processing consistency across the pharmacies. "External nonconformances" were reduced for several categories of medication errors, including wrong-drug selection (33%), wrong directions (49%), and SALA errors (69%). Control charts demonstrated evidence of sustained process improvement and actual reduction in specific medication error elements. Establishing a continuous quality improvement process to ensure that medication errors are minimized is critical to any health care organization providing medication services.

Virtualized MME Design for IoT Support in 5G Systems

PubMed Central

Andres-Maldonado, Pilar; Ameigeiras, Pablo; Prados-Garzon, Jonathan; Ramos-Munoz, Juan Jose; Lopez-Soler, Juan Manuel

2016-01-01

Cellular systems are recently being considered an option to provide support to the Internet of Things (IoT). To enable this support, the 3rd Generation Partnership Project (3GPP) has introduced new procedures specifically targeted for cellular IoT. With one of these procedures, the transmissions of small and infrequent data packets from/to the devices are encapsulated in signaling messages and sent through the control plane. However, these transmissions from/to a massive number of devices may imply a major increase of the processing load on the control plane entities of the network and in particular on the Mobility Management Entity (MME). In this paper, we propose two designs of an MME based on Network Function Virtualization (NFV) that aim at facilitating the IoT support. The first proposed design partially separates the processing resources dedicated to each traffic class. The second design includes traffic shaping to control the traffic of each class. We consider three classes: Mobile Broadband (MBB), low latency Machine to Machine communications (lM2M) and delay-tolerant M2M communications. Our proposals enable reducing the processing resources and, therefore, the cost. Additionally, results show that the proposed designs lessen the impact between classes, so they ease the compliance of the delay requirements of MBB and lM2M communications. PMID:27556468

Quality-assurance plan for the analysis of fluvial sediment by laboratories of the U.S. Geological Survey

USGS Publications Warehouse

Matthes, Wilbur J.; Sholar, Clyde J.; George, John R.

1992-01-01

This report describes procedures used by the Iowa District sediment laboratory of the U.S. Geological Survey to assure the quality of sediment-laboratory data. These procedures can be used by other U.S. Geological Survey laboratories regardless of size and type of operation for quality assurance and quality control of specific sediment-laboratory processes. Also described are the equipment, specifications, calibration and maintenance, and the protocol for methods used in the analyses of fluvial sediment for concentration or particle size.

[Cellular transplantation laboratory: a new field of action for nurses].

PubMed

Corradi, Maria Inês; da Silva, Sandra Honorato

2008-01-01

This article presents the experience of a nurse at a cellular transplantation laboratory. This laboratory goal is to isolate insulin producing cells for human transplantation. The nurse, as a member of an interdisciplinary team, took part in the planning of all work processes: working procedures and team training. The main activities under the nurse responsibilities include contamination control, on-the-job training and evaluation of the Quality of the procedures developed by the interdisciplinary team. Results have shown the effectiveness of the nurses' work in this new field.

Study on the applicability of a precise, accurate method for rapid evaluation of engine and lubricant performance. [determination of wear metal in used lubricating oils

NASA Technical Reports Server (NTRS)

Kinard, J. T.

1975-01-01

The development of a procedure for obtaining data related to wear metal determinations in used lubricants is discussed. The procedure makes it possible to obtain rapid, simultaneous determinations of a number of wear metals at levels of parts per thousand to low parts per billion using a small amount of sample. The electrode assembly and instrumentation used in the process are described. Samples of data obtained from tests conducted under controlled conditions are tabulated.

Effectiveness of HVAC duct cleaning procedures in improving indoor air quality.

PubMed

Ahmad, I; Tansel, B; Mitrani, J D

2001-12-01

Indoor air quality has become one of the most serious environmental concerns as an average person spends about 22 hr indoors on a daily basis. The study reported in this article, was conducted to determine the effectiveness of three commercial HVAC (Heating Ventilation Air Conditioning) duct cleaning processes in reducing the level of airborne particulate matter and viable bioaerosols. The three HVAC sanitation processes were: (1) Contact method (use of conventional vacuum cleaning of interior duct surfaces); (2) Air sweep method (use of compressed air to dislodging dirt and debris); (3) Rotary brush method (insertion of a rotary brush into the ductwork to agitate and dislodge the debris). Effectiveness of these sanitation processes was evaluated in terms of airborne particulate and viable bioaerosol concentrations in residential homes. Eight identical homes were selected in the same neighborhood. Two homes were cleaned using each procedure and two were used as controls. It was found that both particle count readings and bioaerosol concentrations were higher when cleaning was being performed than before or after cleaning, which suggests that dirt, debris and other pollutants may become airborne as a result of disturbances caused by the cleaning processes. Particle count readings at 0.3 micron size were found to have increased due to cigarette smoking. Particle counts at 1.0 micron size were reduced due to HVAC duct cleaning. Post-level bioaerosol concentrations, taken two days after cleaning, were found to be lower than the pre-level concentrations suggesting that the cleaning procedures were effective to some extent. Homes cleaned with the Air Sweep procedure showed the highest degree of reduction in bioaerosol concentration among the three procedures investigated.

Statistical analysis and digital processing of the Mössbauer spectra

NASA Astrophysics Data System (ADS)

Prochazka, Roman; Tucek, Pavel; Tucek, Jiri; Marek, Jaroslav; Mashlan, Miroslav; Pechousek, Jiri

2010-02-01

This work is focused on using the statistical methods and development of the filtration procedures for signal processing in Mössbauer spectroscopy. Statistical tools for noise filtering in the measured spectra are used in many scientific areas. The use of a pure statistical approach in accumulated Mössbauer spectra filtration is described. In Mössbauer spectroscopy, the noise can be considered as a Poisson statistical process with a Gaussian distribution for high numbers of observations. This noise is a superposition of the non-resonant photons counting with electronic noise (from γ-ray detection and discrimination units), and the velocity system quality that can be characterized by the velocity nonlinearities. The possibility of a noise-reducing process using a new design of statistical filter procedure is described. This mathematical procedure improves the signal-to-noise ratio and thus makes it easier to determine the hyperfine parameters of the given Mössbauer spectra. The filter procedure is based on a periodogram method that makes it possible to assign the statistically important components in the spectral domain. The significance level for these components is then feedback-controlled using the correlation coefficient test results. The estimation of the theoretical correlation coefficient level which corresponds to the spectrum resolution is performed. Correlation coefficient test is based on comparison of the theoretical and the experimental correlation coefficients given by the Spearman method. The correctness of this solution was analyzed by a series of statistical tests and confirmed by many spectra measured with increasing statistical quality for a given sample (absorber). The effect of this filter procedure depends on the signal-to-noise ratio and the applicability of this method has binding conditions.

Knowledge engineering for temporal dependency networks as operations procedures. [in space communication

NASA Technical Reports Server (NTRS)

Fayyad, Kristina E.; Hill, Randall W., Jr.; Wyatt, E. J.

1993-01-01

This paper presents a case study of the knowledge engineering process employed to support the Link Monitor and Control Operator Assistant (LMCOA). The LMCOA is a prototype system which automates the configuration, calibration, test, and operation (referred to as precalibration) of the communications, data processing, metric data, antenna, and other equipment used to support space-ground communications with deep space spacecraft in NASA's Deep Space Network (DSN). The primary knowledge base in the LMCOA is the Temporal Dependency Network (TDN), a directed graph which provides a procedural representation of the precalibration operation. The TDN incorporates precedence, temporal, and state constraints and uses several supporting knowledge bases and data bases. The paper provides a brief background on the DSN, and describes the evolution of the TDN and supporting knowledge bases, the process used for knowledge engineering, and an analysis of the successes and problems of the knowledge engineering effort.

Development of alternative data analysis techniques for improving the accuracy and specificity of natural resource inventories made with digital remote sensing data

NASA Technical Reports Server (NTRS)

Lillesand, T. M.; Meisner, D. E. (Principal Investigator)

1980-01-01

An investigation was conducted into ways to improve the involvement of state and local user personnel in the digital image analysis process by isolating those elements of the analysis process which require extensive involvement by field personnel and providing means for performing those activities apart from a computer facility. In this way, the analysis procedure can be converted from a centralized activity focused on a computer facility to a distributed activity in which users can interact with the data at the field office level or in the field itself. A general image processing software was developed on the University of Minnesota computer system (Control Data Cyber models 172 and 74). The use of color hardcopy image data as a primary medium in supervised training procedures was investigated and digital display equipment and a coordinate digitizer were procured.

New techniques for test development for tactical auto-pilots using microprocessors

NASA Astrophysics Data System (ADS)

Shemeta, E. H.

1980-07-01

This paper reports on a demonstration of the application of the method to generate system level tests for a typical tactical missile autopilot. The test algorithms are based on the autopilot control law. When loaded on the tester with appropriate control information, the complete autopilot is tested to establish if the specified control law requirements are met. Thus, the test procedure not only checks to see if the hardware is functional, but also checks the operational software. The technique also uses a 'learning' mode to allow minor timing or functional deviations from the expected responses to be incorporated in the test procedures. A potential application of this test development technique is the extraction of production test data for the various subassemblies. The technique will 'learn' the input-output patterns forming the basis for developement and production tests. If successful, these new techniques should allow the test development process to keep pace with semiconductor progress.

Speeded processing of grammar and tool knowledge in Tourette’s syndrome

PubMed Central

Walenski, Matthew; Mostofsky, Stewart H.; Ullman, Michael T.

2007-01-01

Tourette’s syndrome (TS) is a developmental disorder characterized by motor and verbal tics. The tics, which are fast and involuntary, result from frontal/basal-ganglia abnormalities that lead to unsuppressed behaviors. Language has not been carefully examined in TS. We tested the processing of two basic aspects of language: idiosyncratic and rule-governed linguistic knowledge. Evidence suggests that idiosyncratic knowledge (e.g., in irregular past-tense formation; bring-brought) is stored in a mental lexicon that depends on the temporal-lobe-based declarative memory system that also underlies conceptual knowledge. In contrast, evidence suggests that rule-governed combination (e.g., in regular past-tenses; walk + -ed) takes place in a mental grammar that relies on the frontal/basal-ganglia based procedural memory system, which also underlies motor skills such as how to use a hammer. We found that TS children were significantly faster than typically-developing control children at producing rule-governed past-tenses (slip-slipped, plim-plimmed, bring-bringed) but not irregular and other unpredictable past-tenses (bring-brought, splim-splam). They were also faster than controls at naming pictures of manipulated (hammer) but not non-manipulated (elephant) items. These data were not explained by a wide range of potentially confounding subject- and item-level factors. The results suggest that the processing of procedurally-based knowledge, both of grammar and of manipulated objects, is particularly speeded in TS. The frontal/basal-ganglia abnormalities may thus lead not only to tics, but to a wider range of rapid behaviors, including in the cognitive processing of rule-governed forms in language and other types of procedural knowledge. PMID:17493643

40 CFR 63.1326 - Batch process vents-recordkeeping provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... single highest-HAP recipe. (3) Total annual uncontrolled TOC or organic HAP emissions, determined at the...): (i) For an incinerator or non-combustion control device, the percent reduction of organic HAP or TOC... percent reduction of organic HAP or TOC achieved, as determined using the procedures specified in § 63...

MEASUREMENT AND PREDICTION OF THE RESISTIVITY OF ASH/SORBENT MIXTURES PRODUCED BY SULFUR OXIDE CONTROL PROCESSES

EPA Science Inventory

The report describes the development of (1) a modified procedure for obtaining consistent and reproducible laboratory resistivity values for mixtures of coal fly ash and partially spent sorbent, and (2) an approach for predicting resistivity based on the chemical composition of t...

Programmed Instruction, Self-Control, and In-Patient Psychiatry.

ERIC Educational Resources Information Center

Layng, Terrence; And Others

The extension of the instructional programming process, as outlined by Markle and Tiemann (1967), to the treatment of psychiatric in-patients is described. Three case studies are presented as examples of the application of the programming procedures as derived from the Constructional Model of Dr. Israel Goldiamond. The emphasis throughout all…

State vs. Local Control: Reality or Myth over Concern for Local Autonomy.

ERIC Educational Resources Information Center

Mundt, John C.

1978-01-01

As examples of the trend towards decision-making processes resting on the interaction of various legitimate public sector interests, the author considers outside forces producing operational strictures within the system, including executive orders, lapsing and allotment procedures, accounting requirements, information demands, legal opinions,…

Nursing Principles & Skills. Teacher Edition.

ERIC Educational Resources Information Center

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This curriculum guide contains 14 units for a course on nursing principles and skills needed by practical nurses. The 14 units of instruction cover the following: (1) using medical terminology; (2) practicing safety procedures; (3) using the nursing process for care planning; (4) using infection control techniques; (5) preparing a patient…

The Quasi-Privatization of a Public Honors College

ERIC Educational Resources Information Center

Berdahl, Robert; Contardo, Jeanne Bayer

2006-01-01

This is a case study of a state institution granted charter status in 1992 in exchange for capping its request for state funds. St. Mary's College of Maryland received widespread freedom from state procedural controls, including procurement, personnel, and some capital development processes. The state, however, retained its oversight of the…

76 FR 71932 - Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-21

... Control Number: 1505-0237. Abstract: Section 1042 of the Dodd-Frank Wall Street Reform and Consumer... procedures that govern the process, described in Section 1042(b) of the Dodd-Frank Act, by which state... 1042(a) to enforce the Dodd-Frank Act or regulations prescribed thereunder. In accordance with the...

75 FR 40839 - Agency Information Collection Activities; Proposed Collection; Comment Request; Hazard Analysis...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-14

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-N-0357] Agency Information Collection Activities; Proposed Collection; Comment Request; Hazard Analysis and Critical Control Point Procedures for the Safe and Sanitary Processing and Importing of Juice AGENCY: Food...

15 CFR 750.4 - Procedures for processing license applications.

Code of Federal Regulations, 2013 CFR

2013-01-01

... interagency groups established to provide expertise and coordinate interagency consultation. These interagency groups consist of: (i) The Missile Technology Export Control Group (MTEC). The MTEC, chaired by the... paper copy. (d) Review by other agencies and/or interagency groups. (1) Within 10 days of receipt of a...

15 CFR 750.4 - Procedures for processing license applications.

Code of Federal Regulations, 2011 CFR

2011-01-01

... interagency groups established to provide expertise and coordinate interagency consultation. These interagency groups consist of: (i) The Missile Technology Export Control Group (MTEC). The MTEC, chaired by the... paper copy. (d) Review by other agencies and/or interagency groups. (1) Within 10 days of receipt of a...

15 CFR 750.4 - Procedures for processing license applications.

Code of Federal Regulations, 2012 CFR

2012-01-01

... interagency groups established to provide expertise and coordinate interagency consultation. These interagency groups consist of: (i) The Missile Technology Export Control Group (MTEC). The MTEC, chaired by the... paper copy. (d) Review by other agencies and/or interagency groups. (1) Within 10 days of receipt of a...

15 CFR 750.4 - Procedures for processing license applications.

Code of Federal Regulations, 2014 CFR

2014-01-01

... interagency groups established to provide expertise and coordinate interagency consultation. These interagency groups consist of: (i) The Missile Technology Export Control Group (MTEC). The MTEC, chaired by the... paper copy. (d) Review by other agencies and/or interagency groups. (1) Within 10 days of receipt of a...

15 CFR 750.4 - Procedures for processing license applications.

Code of Federal Regulations, 2010 CFR

2010-01-01

... interagency groups established to provide expertise and coordinate interagency consultation. These interagency groups consist of: (i) The Missile Technology Export Control Group (MTEC). The MTEC, chaired by the... paper copy. (d) Review by other agencies and/or interagency groups. (1) Within 10 days of receipt of a...

78 FR 69689 - Agency Information Collection Activities; Proposed Collection; Comment Request; Hazard Analysis...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-20

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2013-N-1427... Critical Control Point Procedures for the Safe and Sanitary Processing and Importing of Juice AGENCY: Food and Drug Administration, HHS. ACTION: Notice. SUMMARY: The Food and Drug Administration (FDA) is...