Application of Multi-Threshold NULL Convention Logic to Adaptive Beamforming Circuits for Ultra-Low Power

DTIC Science & Technology

2016-03-31

Abstract: With the decrease of transistor feature sizes into the ultra-deep submicron range, leakage power becomes an important design challenge for...MTNCL design showed substantial improvements in terms of active energy and leakage power compared to the equivalent synchronous design. Keywords...switching could use a large portion of power. Additionally, leakage power has come to dominate power consumption as process sizes shrink. Adaptive

Overview of the production of sintered SiC optics and optical sub-assemblies

NASA Astrophysics Data System (ADS)

Williams, S.; Deny, P.

2005-08-01

The following is an overview on sintered silicon carbide (SSiC) material properties and processing requirements for the manufacturing of components for advanced technology optical systems. The overview will compare SSiC material properties to typical materials used for optics and optical structures. In addition, it will review manufacturing processes required to produce optical components in detail by process step. The process overview will illustrate current manufacturing process and concepts to expand the process size capability. The overview will include information on the substantial capital equipment employed in the manufacturing of SSIC. This paper will also review common in-process inspection methodology and design rules. The design rules are used to improve production yield, minimize cost, and maximize the inherent benefits of SSiC for optical systems. Optimizing optical system designs for a SSiC manufacturing process will allow systems designers to utilize SSiC as a low risk, cost competitive, and fast cycle time technology for next generation optical systems.

Lithography process for patterning HgI2 photonic devices

DOEpatents

Mescher, Mark J.; James, Ralph B.; Hermon, Haim

2004-11-23

A photolithographic process forms patterns on HgI.sub.2 surfaces and defines metal sublimation masks and electrodes to substantially improve device performance by increasing the realizable design space. Techniques for smoothing HgI.sub.2 surfaces and for producing trenches in HgI.sub.2 are provided. A sublimation process is described which produces etched-trench devices with enhanced electron-transport-only behavior.

Design and cost analysis of rapid aquifer restoration systems using flow simulation and quadratic programming.

USGS Publications Warehouse

Lefkoff, L.J.; Gorelick, S.M.

1986-01-01

Detailed two-dimensional flow simulation of a complex ground-water system is combined with quadratic and linear programming to evaluate design alternatives for rapid aquifer restoration. Results show how treatment and pumping costs depend dynamically on the type of treatment process, and capacity of pumping and injection wells, and the number of wells. The design for an inexpensive treatment process minimizes pumping costs, while an expensive process results in the minimization of treatment costs. Substantial reductions in pumping costs occur with increases in injection capacity or in the number of wells. Treatment costs are reduced by expansions in pumping capacity or injecion capacity. The analysis identifies maximum pumping and injection capacities.-from Authors

Optimum process design of packed bed type thermal storage systems and other applications

DOEpatents

Bindra, Hitesh; Bueno, Pablo

2016-10-25

Methods and systems for optimizing the process of heat and/or mass transfer operations in packed beds and embodiments of applications of the methods are disclosed herein below. In one instance, the method results in the profile of the quantity representative of the heat and/or mass transfer operation having a propagating substantially sharp front.

Highly Non-Linear Optical (NLO) organic crystals and films. Electrooptical organic materials

NASA Technical Reports Server (NTRS)

Mcmanus, Samuel P.; Rosenberger, Franz; Matthews, John

1987-01-01

Devices employing nonlinear optics (NLO) hold great promise for important applications in integrated optics, optical information processing and telecommunications. Properly designed organics possess outstanding optical and electrooptical properties which will substantially advance many technologies including electrooptical switching, optical amplification for communications, and parallel processing for hybrid optical computers. A brief comparison of organic and inorganic materials is given.

The Computer Aided Aircraft-design Package (CAAP)

NASA Technical Reports Server (NTRS)

Yalif, Guy U.

1994-01-01

The preliminary design of an aircraft is a complex, labor-intensive, and creative process. Since the 1970's, many computer programs have been written to help automate preliminary airplane design. Time and resource analyses have identified, 'a substantial decrease in project duration with the introduction of an automated design capability'. Proof-of-concept studies have been completed which establish 'a foundation for a computer-based airframe design capability', Unfortunately, today's design codes exist in many different languages on many, often expensive, hardware platforms. Through the use of a module-based system architecture, the Computer aided Aircraft-design Package (CAAP) will eventually bring together many of the most useful features of existing programs. Through the use of an expert system, it will add an additional feature that could be described as indispensable to entry level engineers and students: the incorporation of 'expert' knowledge into the automated design process.

The NMCSSC Quick-Reacting General War Gaming System (QUICK). Analytical Manual. Volume I - Data Base Preparation. Change

DTIC Science & Technology

1972-02-21

is a two-sided strategic nuclear exchange war gaming system. It is designed co assist the military planner in examining various facets of strategic...substantial, the data base preparation process is designed to provide an efficient means of assembling, maintaining, and organizing an input data base to... designed to assist in the study of &’trategic conflicts involving a large-scale Pexchange of nuclear weapons. The system is structured into five

Streamlining the Design-to-Build Transition with Build-Optimization Software Tools.

PubMed

Oberortner, Ernst; Cheng, Jan-Fang; Hillson, Nathan J; Deutsch, Samuel

2017-03-17

Scaling-up capabilities for the design, build, and test of synthetic biology constructs holds great promise for the development of new applications in fuels, chemical production, or cellular-behavior engineering. Construct design is an essential component in this process; however, not every designed DNA sequence can be readily manufactured, even using state-of-the-art DNA synthesis methods. Current biological computer-aided design and manufacture tools (bioCAD/CAM) do not adequately consider the limitations of DNA synthesis technologies when generating their outputs. Designed sequences that violate DNA synthesis constraints may require substantial sequence redesign or lead to price-premiums and temporal delays, which adversely impact the efficiency of the DNA manufacturing process. We have developed a suite of build-optimization software tools (BOOST) to streamline the design-build transition in synthetic biology engineering workflows. BOOST incorporates knowledge of DNA synthesis success determinants into the design process to output ready-to-build sequences, preempting the need for sequence redesign. The BOOST web application is available at https://boost.jgi.doe.gov and its Application Program Interfaces (API) enable integration into automated, customized DNA design processes. The herein presented results highlight the effectiveness of BOOST in reducing DNA synthesis costs and timelines.

Simplify to survive: prescriptive layouts ensure profitable scaling to 32nm and beyond

NASA Astrophysics Data System (ADS)

Liebmann, Lars; Pileggi, Larry; Hibbeler, Jason; Rovner, Vyacheslav; Jhaveri, Tejas; Northrop, Greg

2009-03-01

The time-to-market driven need to maintain concurrent process-design co-development, even in spite of discontinuous patterning, process, and device innovation is reiterated. The escalating design rule complexity resulting from increasing layout sensitivities in physical and electrical yield and the resulting risk to profitable technology scaling is reviewed. Shortcomings in traditional Design for Manufacturability (DfM) solutions are identified and contrasted to the highly successful integrated design-technology co-optimization used for SRAM and other memory arrays. The feasibility of extending memory-style design-technology co-optimization, based on a highly simplified layout environment, to logic chips is demonstrated. Layout density benefits, modeled patterning and electrical yield improvements, as well as substantially improved layout simplicity are quantified in a conventional versus template-based design comparison on a 65nm IBM PowerPC 405 microprocessor core. The adaptability of this highly regularized template-based design solution to different yield concerns and design styles is shown in the extension of this work to 32nm with an increased focus on interconnect redundancy. In closing, the work not covered in this paper, focused on the process side of the integrated process-design co-optimization, is introduced.

CLARA: CLAS12 Reconstruction and Analysis Framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gyurjyan, Vardan; Matta, Sebastian Mancilla; Oyarzun, Ricardo

2016-11-01

In this paper we present SOA based CLAS12 event Reconstruction and Analyses (CLARA) framework. CLARA design focus is on two main traits: real-time data stream processing, and service-oriented architecture (SOA) in a flow based programming (FBP) paradigm. Data driven and data centric architecture of CLARA presents an environment for developing agile, elastic, multilingual data processing applications. The CLARA framework presents solutions capable of processing large volumes of data interactively and substantially faster than batch systems.

Five Faces of Cognition: Theoretical Influences on Approaches to Learning Disabilities.

ERIC Educational Resources Information Center

Hresko, Wayne P.; Reid, D. Kim

1988-01-01

The article points out that the label "cognitive" has been used to designate five substantially different approaches to learning disabilities: information processing, metacognition, genetic epistemology, cognitive behavior modification, and the specific-abilities model. Despite the similar label, the instructional interventions of these approaches…

Options for a lunar base surface architecture

NASA Technical Reports Server (NTRS)

Roberts, Barney B.

1992-01-01

The Planet Surface Systems Office at the NASA Johnson Space Center has participated in an analysis of the Space Exploration Initiative architectures described in the Synthesis Group report. This effort involves a Systems Engineering and Integration effort to define point designs for evolving lunar and Mars bases that support substantial science, exploration, and resource production objectives. The analysis addresses systems-level designs; element requirements and conceptual designs; assessments of precursor and technology needs; and overall programmatics and schedules. This paper focuses on the results of the study of the Space Resource Utilization Architecture. This architecture develops the capability to extract useful materials from the indigenous resources of the Moon and Mars. On the Moon, a substantial infrastructure is emplaced which can support a crew of up to twelve. Two major process lines are developed: one produces oxygen, ceramics, and metals; the other produces hydrogen, helium, and other volatiles. The Moon is also used for a simulation of a Mars mission. Significant science capabilities are established in conjunction with resource development. Exploration includes remote global surveys and piloted sorties of local and regional areas. Science accommodations include planetary science, astronomy, and biomedical research. Greenhouses are established to provide a substantial amount of food needs.

Test Facilities and Experience on Space Nuclear System Developments at the Kurchatov Institute

NASA Astrophysics Data System (ADS)

Ponomarev-Stepnoi, Nikolai N.; Garin, Vladimir P.; Glushkov, Evgeny S.; Kompaniets, George V.; Kukharkin, Nikolai E.; Madeev, Vicktor G.; Papin, Vladimir K.; Polyakov, Dmitry N.; Stepennov, Boris S.; Tchuniyaev, Yevgeny I.; Tikhonov, Lev Ya.; Uksusov, Yevgeny I.

2004-02-01

The complexity of space fission systems and rigidity of requirement on minimization of weight and dimension characteristics along with the wish to decrease expenditures on their development demand implementation of experimental works which results shall be used in designing, safety substantiation, and licensing procedures. Experimental facilities are intended to solve the following tasks: obtainment of benchmark data for computer code validations, substantiation of design solutions when computational efforts are too expensive, quality control in a production process, and ``iron'' substantiation of criticality safety design solutions for licensing and public relations. The NARCISS and ISKRA critical facilities and unique ORM facility on shielding investigations at the operating OR nuclear research reactor were created in the Kurchatov Institute to solve the mentioned tasks. The range of activities performed at these facilities within the implementation of the previous Russian nuclear power system programs is briefly described in the paper. This experience shall be analyzed in terms of methodological approach to development of future space nuclear systems (this analysis is beyond this paper). Because of the availability of these facilities for experiments, the brief description of their critical assemblies and characteristics is given in this paper.

Modeling of wastewater treatment system of car parks from petroleum products

NASA Astrophysics Data System (ADS)

Savdur, S. N.; Stepanova, Yu V.; Kodolova, I. A.; Fesina, E. L.

2018-05-01

The paper discusses the technological complex of wastewater treatment of car parks from petroleum products. Based on the review of the main modeling methods of discrete-continuous chemical and engineering processes, it substantiates expediency of using the theory of Petri nets (PN) for modeling the process of wastewater treatment of car parks from petroleum products. It is proposed to use a modification of Petri nets which is focused on modeling and analysis of discrete-continuous chemical and engineering processes by prioritizing transitions, timing marks in positions and transitions. A model in the form of modified Petri nets (MPN) is designed. A software package to control the process for wastewater treatment is designed by means of SCADA TRACE MODE.

Single-cell transcriptome conservation in cryopreserved cells and tissues.

PubMed

Guillaumet-Adkins, Amy; Rodríguez-Esteban, Gustavo; Mereu, Elisabetta; Mendez-Lago, Maria; Jaitin, Diego A; Villanueva, Alberto; Vidal, August; Martinez-Marti, Alex; Felip, Enriqueta; Vivancos, Ana; Keren-Shaul, Hadas; Heath, Simon; Gut, Marta; Amit, Ido; Gut, Ivo; Heyn, Holger

2017-03-01

A variety of single-cell RNA preparation procedures have been described. So far, protocols require fresh material, which hinders complex study designs. We describe a sample preservation method that maintains transcripts in viable single cells, allowing one to disconnect time and place of sampling from subsequent processing steps. We sequence single-cell transcriptomes from >1000 fresh and cryopreserved cells using 3'-end and full-length RNA preparation methods. Our results confirm that the conservation process did not alter transcriptional profiles. This substantially broadens the scope of applications in single-cell transcriptomics and could lead to a paradigm shift in future study designs.

Transfer of the epoxidation of soybean oil from batch to flow chemistry guided by cost and environmental issues.

PubMed

Kralisch, Dana; Streckmann, Ina; Ott, Denise; Krtschil, Ulich; Santacesaria, Elio; Di Serio, Martino; Russo, Vincenzo; De Carlo, Lucrezia; Linhart, Walter; Christian, Engelbert; Cortese, Bruno; de Croon, Mart H J M; Hessel, Volker

2012-02-13

The simple transfer of established chemical production processes from batch to flow chemistry does not automatically result in more sustainable ones. Detailed process understanding and the motivation to scrutinize known process conditions are necessary factors for success. Although the focus is usually "only" on intensifying transport phenomena to operate under intrinsic kinetics, there is also a large intensification potential in chemistry under harsh conditions and in the specific design of flow processes. Such an understanding and proposed processes are required at an early stage of process design because decisions on the best-suited tools and parameters required to convert green engineering concepts into practice-typically with little chance of substantial changes later-are made during this period. Herein, we present a holistic and interdisciplinary process design approach that combines the concept of novel process windows with process modeling, simulation, and simplified cost and lifecycle assessment for the deliberate development of a cost-competitive and environmentally sustainable alternative to an existing production process for epoxidized soybean oil. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

10 CFR 725.15 - Requirements for approval of applications.

Code of Federal Regulations, 2010 CFR

2010-01-01

... and/or operation of production or manufacturing facilities and offers reasonable assurance of adequacy... Production will be approved only if the application demonstrates also that the applicant: (i) Is directly engaged in a substantial effort to develop, design, build or operate a chemical processing plant or other...

Heuristic decomposition for non-hierarchic systems

NASA Technical Reports Server (NTRS)

Bloebaum, Christina L.; Hajela, P.

1991-01-01

Design and optimization is substantially more complex in multidisciplinary and large-scale engineering applications due to the existing inherently coupled interactions. The paper introduces a quasi-procedural methodology for multidisciplinary optimization that is applicable for nonhierarchic systems. The necessary decision-making support for the design process is provided by means of an embedded expert systems capability. The method employs a decomposition approach whose modularity allows for implementation of specialized methods for analysis and optimization within disciplines.

High temperature solar thermal receiver

NASA Technical Reports Server (NTRS)

1979-01-01

A design concept for a high temperature solar thermal receiver to operate at 3 atmospheres pressure and 2500 F outlet was developed. The performance and complexity of windowed matrix, tube-header, and extended surface receivers were evaluated. The windowed matrix receiver proved to offer substantial cost and performance benefits. An efficient and cost effective hardware design was evaluated for a receiver which can be readily interfaced to fuel and chemical processes or to heat engines for power generation.

Framework for Multidisciplinary Analysis, Design, and Optimization with High-Fidelity Analysis Tools

NASA Technical Reports Server (NTRS)

Orr, Stanley A.; Narducci, Robert P.

2009-01-01

A plan is presented for the development of a high fidelity multidisciplinary optimization process for rotorcraft. The plan formulates individual disciplinary design problems, identifies practical high-fidelity tools and processes that can be incorporated in an automated optimization environment, and establishes statements of the multidisciplinary design problem including objectives, constraints, design variables, and cross-disciplinary dependencies. Five key disciplinary areas are selected in the development plan. These are rotor aerodynamics, rotor structures and dynamics, fuselage aerodynamics, fuselage structures, and propulsion / drive system. Flying qualities and noise are included as ancillary areas. Consistency across engineering disciplines is maintained with a central geometry engine that supports all multidisciplinary analysis. The multidisciplinary optimization process targets the preliminary design cycle where gross elements of the helicopter have been defined. These might include number of rotors and rotor configuration (tandem, coaxial, etc.). It is at this stage that sufficient configuration information is defined to perform high-fidelity analysis. At the same time there is enough design freedom to influence a design. The rotorcraft multidisciplinary optimization tool is built and substantiated throughout its development cycle in a staged approach by incorporating disciplines sequentially.

High friction interactive aircraft tire-runway systems

NASA Technical Reports Server (NTRS)

Clark, S. K.

1974-01-01

The principle of utilizing geometric interaction between runway asperities and tire pattern design is discussed, and a theoretical basis is presented for substantial enhancement of frictional effects by this process. Test data confirming this is given. First order analytical expressions are given for the increased friction coefficients and for the engagement distances required. High speed friction data on a 7.00 x 8 aircraft tire is presented confirming this. Example design geometries are shown for the tire tread groove pattern, and designs and materials are discussed for the asperity grid and its attachment system.

The influence of international standards on optomechanical design

NASA Astrophysics Data System (ADS)

Parks, Robert E.

1992-12-01

In the last 10 to 15 years, a considerable body of international standards literature has been published on both mechanical and optical design. We discuss the influence of these internationally developed standards on the design and fabrication of optical systems. We conclude that while there are large benefits to be gained from using these international standards, there will have to be a substantial educational effort at all levels from project scientist to worker on the shop floor to take advantage of the benefits. Many sources to help in this education process are outlined.

A quality-by-design approach to risk reduction and optimization for human embryonic stem cell cryopreservation processes.

PubMed

Mitchell, Peter D; Ratcliffe, Elizabeth; Hourd, Paul; Williams, David J; Thomas, Robert J

2014-12-01

It is well documented that cryopreservation and resuscitation of human embryonic stem cells (hESCs) is complex and ill-defined, and often suffers poor cell recovery and increased levels of undesirable cell differentiation. In this study we have applied Quality-by-Design (QbD) concepts to the critical processes of slow-freeze cryopreservation and resuscitation of hESC colony cultures. Optimized subprocesses were linked together to deliver a controlled complete process. We have demonstrated a rapid, high-throughput, and stable system for measurement of cell adherence and viability as robust markers of in-process and postrecovery cell state. We observed that measurement of adherence and viability of adhered cells at 1 h postseeding was predictive of cell proliferative ability up to 96 h in this system. Application of factorial design defined the operating spaces for cryopreservation and resuscitation, critically linking the performance of these two processes. Optimization of both processes resulted in enhanced reattachment and post-thaw viability, resulting in substantially greater recovery of cryopreserved, pluripotent cell colonies. This study demonstrates the importance of QbD concepts and tools for rapid, robust, and low-risk process design that can inform manufacturing controls and logistics.

Design and implementation of a patient navigation system in rural Nepal: Improving patient experience in resource-constrained settings.

PubMed

Raut, Anant; Thapa, Poshan; Citrin, David; Schwarz, Ryan; Gauchan, Bikash; Bista, Deepak; Tamrakar, Bibhu; Halliday, Scott; Maru, Duncan; Schwarz, Dan

2015-12-01

Patient navigation programs have shown to be effective across multiple settings in guiding patients through the care delivery process. Limited experience and literature exist, however, for such programs in rural and resource-constrained environments. Patients living in such settings frequently have low health literacy and substantially lower social status than their providers. They typically have limited experiences interfacing with formalized healthcare systems, and, when they do, their experience can be unpleasant and confusing. At a district hospital in rural far-western Nepal, we designed and implemented a patient navigation system that aimed to improve patients' subjective care experience. First, we hired and trained a team of patient navigators who we recruited from the local area. Their responsibility is exclusively to demonstrate compassion and to guide patients through their care process. Second, we designed visual cues throughout our hospital complex to assist in navigating patients through the buildings. Third, we incorporated the patient navigators within the management and communications systems of the hospital care team, and established standard operating procedures. We describe here our experiences and challenges in designing and implementing a patient navigator program. Such patient-centered systems may be relevant at other facilities in Nepal and globally where patient health literacy is low, patients come from backgrounds of substantial marginalization and disempowerment, and patient experience with healthcare facilities is limited. Copyright © 2015 Elsevier Inc. All rights reserved.

Perceptions of Challenging Tasks and Achievement by New Zealand Students

ERIC Educational Resources Information Center

Linsell, Chris; Holmes, Marilyn; Sullivan, Peter

2016-01-01

This paper examines the learning by students who were participating in a project designed to promote persistence while working on mathematical tasks. We examined their learning of mathematics concepts and learning about the processes of engaging in mathematical tasks. There were substantial increases in students' knowledge of angles and also…

Design for Additive Bio-Manufacturing: From Patient-Specific Medical Devices to Rationally Designed Meta-Biomaterials.

PubMed

Zadpoor, Amir A

2017-07-25

Recent advances in additive manufacturing (AM) techniques in terms of accuracy, reliability, the range of processable materials, and commercial availability have made them promising candidates for production of functional parts including those used in the biomedical industry. The complexity-for-free feature offered by AM means that very complex designs become feasible to manufacture, while batch-size-indifference enables fabrication of fully patient-specific medical devices. Design for AM (DfAM) approaches aim to fully utilize those features for development of medical devices with substantially enhanced performance and biomaterials with unprecedented combinations of favorable properties that originate from complex geometrical designs at the micro-scale. This paper reviews the most important approaches in DfAM particularly those applicable to additive bio-manufacturing including image-based design pipelines, parametric and non-parametric designs, metamaterials, rational and computationally enabled design, topology optimization, and bio-inspired design. Areas with limited research have been identified and suggestions have been made for future research. The paper concludes with a brief discussion on the practical aspects of DfAM and the potential of combining AM with subtractive and formative manufacturing processes in so-called hybrid manufacturing processes.

Design for Additive Bio-Manufacturing: From Patient-Specific Medical Devices to Rationally Designed Meta-Biomaterials

PubMed Central

Zadpoor, Amir A.

2017-01-01

Recent advances in additive manufacturing (AM) techniques in terms of accuracy, reliability, the range of processable materials, and commercial availability have made them promising candidates for production of functional parts including those used in the biomedical industry. The complexity-for-free feature offered by AM means that very complex designs become feasible to manufacture, while batch-size-indifference enables fabrication of fully patient-specific medical devices. Design for AM (DfAM) approaches aim to fully utilize those features for development of medical devices with substantially enhanced performance and biomaterials with unprecedented combinations of favorable properties that originate from complex geometrical designs at the micro-scale. This paper reviews the most important approaches in DfAM particularly those applicable to additive bio-manufacturing including image-based design pipelines, parametric and non-parametric designs, metamaterials, rational and computationally enabled design, topology optimization, and bio-inspired design. Areas with limited research have been identified and suggestions have been made for future research. The paper concludes with a brief discussion on the practical aspects of DfAM and the potential of combining AM with subtractive and formative manufacturing processes in so-called hybrid manufacturing processes. PMID:28757572

Allied health clinicians using translational research in action to develop a reliable stroke audit tool.

PubMed

Abery, Philip; Kuys, Suzanne; Lynch, Mary; Low Choy, Nancy

2018-05-23

To design and establish reliability of a local stroke audit tool by engaging allied health clinicians within a privately funded hospital. Design: Two-stage study involving a modified Delphi process to inform stroke audit tool development and inter-tester reliability. Allied health clinicians. A modified Delphi process to select stroke guideline recommendations for inclusion in the audit tool. Reliability study: 1 allied health representative from each discipline audited 10 clinical records with sequential admissions to acute and rehabilitation services. Recommendations were admitted to the audit tool when 70% agreement was reached, with 50% set as the reserve agreement. Inter-tester reliability was determined using intra-class correlation coefficients (ICCs) across 10 clinical records. Twenty-two participants (92% female, 50% physiotherapists, 17% occupational therapists) completed the modified Delphi process. Across 6 voting rounds, 8 recommendations reached 70% agreement and 2 reached 50% agreement. Two recommendations (nutrition/hydration; goal setting) were added to ensure representation for all disciplines. Substantial consistency across raters was established for the audit tool applied in acute stroke (ICC .71; range .48 to .90) and rehabilitation (ICC.78; range .60 to .93) services. Allied health clinicians within a privately funded hospital generally agreed in an audit process to develop a reliable stroke audit tool. Allied health clinicians agreed on stroke guideline recommendations to inform a stroke audit tool. The stroke audit tool demonstrated substantial consistency supporting future use for service development. This process, which engages local clinicians, could be adopted by other facilities to design reliable audit tools to identify local service gaps to inform changes to clinical practice. © 2018 John Wiley & Sons, Ltd.

Adaptive subdomain modeling: A multi-analysis technique for ocean circulation models

NASA Astrophysics Data System (ADS)

Altuntas, Alper; Baugh, John

2017-07-01

Many coastal and ocean processes of interest operate over large temporal and geographical scales and require a substantial amount of computational resources, particularly when engineering design and failure scenarios are also considered. This study presents an adaptive multi-analysis technique that improves the efficiency of these computations when multiple alternatives are being simulated. The technique, called adaptive subdomain modeling, concurrently analyzes any number of child domains, with each instance corresponding to a unique design or failure scenario, in addition to a full-scale parent domain providing the boundary conditions for its children. To contain the altered hydrodynamics originating from the modifications, the spatial extent of each child domain is adaptively adjusted during runtime depending on the response of the model. The technique is incorporated in ADCIRC++, a re-implementation of the popular ADCIRC ocean circulation model with an updated software architecture designed to facilitate this adaptive behavior and to utilize concurrent executions of multiple domains. The results of our case studies confirm that the method substantially reduces computational effort while maintaining accuracy.

Laser processing of solar cells with anti-reflective coating

DOEpatents

Harley, Gabriel; Smith, David D.; Dennis, Tim; Waldhauer, Ann; Kim, Taeseok; Cousins, Peter John

2016-02-16

Contact holes of solar cells are formed by laser ablation to accommodate various solar cell designs. Use of a laser to form the contact holes is facilitated by replacing films formed on the diffusion regions with a film that has substantially uniform thickness. Contact holes may be formed to deep diffusion regions to increase the laser ablation process margins. The laser configuration may be tailored to form contact holes through dielectric films of varying thicknesses.

Filament-wound graphite/epoxy rocket motor case

NASA Technical Reports Server (NTRS)

Humphrey, W. D.; Schmidt, W. W.

1972-01-01

The fabrication procedures are described for a filament-wound rocket motor case, approximately 56 cm long x 71 cm diameter, utilizing high tensile strength graphite fibers. The process utilized Fiberite Hy-E-1330B prepreg tape which consists of Courtaulds HTS fibers in a temperature-sensitive epoxy matrix. This fabrication effort, with resultant design, material and process recommendations, substantiates the manufacturing feasibility of graphite/epoxy rocket motor cases in the 56 cm x 71 cm size range.

Turboexpander plant designs can provide high ethane recovery without inlet CO/sub 2/ removal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilkinson, J.D.; Hudson, H.M.

1982-05-03

New turboexpander plant designs can process natural gas streams containing moderate amounts of carbon dioxide (CO/sub 2/) for high ethane recovery without inlet gas treating. The designs will handle a wide range of inlet ethane-plus fractions. They also offer reduced horsepower requirements compared to other processes. CO/sub 2/ is a typical component of most natural gas streams. In many cases, processing of these gas streams in a turboexpander plant for high ethane recovery requires pre-treatment of the gas for CO/sub 2/ removal. This is required to avoid the formation of solid CO/sub 2/ (freezing) in the cold sections of themore » process and/or to meet necessary residue gas and liquid product CO/sub 2/ specifications. Depending on the quantities involved, the CO/sub 2/ removal systems is generally a significant portion of both the installed cost and operating cost for the ethane recovery facility. Therefore, turboexpander plant designs that are capable of handling increased quantities of CO/sub 2/ in the feed gas without freezing can offer the gas processor substantial economic benefits.« less

Quantification of uncertainty in machining operations for on-machine acceptance.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Claudet, Andre A.; Tran, Hy D.; Su, Jiann-Chemg

2008-09-01

Manufactured parts are designed with acceptance tolerances, i.e. deviations from ideal design conditions, due to unavoidable errors in the manufacturing process. It is necessary to measure and evaluate the manufactured part, compared to the nominal design, to determine whether the part meets design specifications. The scope of this research project is dimensional acceptance of machined parts; specifically, parts machined using numerically controlled (NC, or also CNC for Computer Numerically Controlled) machines. In the design/build/accept cycle, the designer will specify both a nominal value, and an acceptable tolerance. As part of the typical design/build/accept business practice, it is required to verifymore » that the part did meet acceptable values prior to acceptance. Manufacturing cost must include not only raw materials and added labor, but also the cost of ensuring conformance to specifications. Ensuring conformance is a substantial portion of the cost of manufacturing. In this project, the costs of measurements were approximately 50% of the cost of the machined part. In production, cost of measurement would be smaller, but still a substantial proportion of manufacturing cost. The results of this research project will point to a science-based approach to reducing the cost of ensuring conformance to specifications. The approach that we take is to determine, a priori, how well a CNC machine can manufacture a particular geometry from stock. Based on the knowledge of the manufacturing process, we are then able to decide features which need further measurements from features which can be accepted 'as is' from the CNC. By calibration of the machine tool, and establishing a machining accuracy ratio, we can validate the ability of CNC to fabricate to a particular level of tolerance. This will eliminate the costs of checking for conformance for relatively large tolerances.« less

Data systems trade studies for a next generation sensor

NASA Astrophysics Data System (ADS)

Masuoka, Edward J.; Fleig, Albert J.

1997-01-01

Processing system designers must make substantial changes to accommodate current and anticipated improvements in remote sensing instruments.Increases in the spectral, radiometric and geometric resolution lead to data rates, processing loads and storage volumes which far exceed the ability of most current computer systems. To accommodate user expectations, the data must be processed and made available quickly in a convenient and easy to use form. This paper describes design trade-offs made in developing the processing system for the moderate resolution imaging spectroradiometer, MODIS, which will fly on the Earth Observing System's, AM-1 spacecraft to be launched in 1998. MODIS will have an average continuous date rate of 6.2 Mbps and require processing at 6.5 GFLOPS to produce 600GB of output products per day. Specific trade-offs occur in the areas of science software portability and usability of science products versus overall system performance and throughput.

CFD Research, Parallel Computation and Aerodynamic Optimization

NASA Technical Reports Server (NTRS)

Ryan, James S.

1995-01-01

During the last five years, CFD has matured substantially. Pure CFD research remains to be done, but much of the focus has shifted to integration of CFD into the design process. The work under these cooperative agreements reflects this trend. The recent work, and work which is planned, is designed to enhance the competitiveness of the US aerospace industry. CFD and optimization approaches are being developed and tested, so that the industry can better choose which methods to adopt in their design processes. The range of computer architectures has been dramatically broadened, as the assumption that only huge vector supercomputers could be useful has faded. Today, researchers and industry can trade off time, cost, and availability, choosing vector supercomputers, scalable parallel architectures, networked workstations, or heterogenous combinations of these to complete required computations efficiently.

Cognitive Training for Children: Effects on Inductive Reasoning, Deductive Reasoning, and Mathematics Achievement in an Australian School Setting

ERIC Educational Resources Information Center

Barkl, Sophie; Porter, Amy; Ginns, Paul

2012-01-01

Inductive reasoning is a core cognitive process of fluid intelligence, predicting a variety of educational outcomes. The Cognitive Training for Children (CTC) program is an educational intervention designed to develop children's inductive reasoning skills, with previous investigations finding substantial effects of the program on both inductive…

Neighborhood-Level Social Processes and Substantiated Cases of Child Maltreatment

PubMed Central

Molnar, Beth E.; Goerge, Robert M.; Gilsanz, Paola; Hill, Andrea; Subramanian, SV; Holton, John K.; Duncan, Dustin T.; Beatriz, Elizabeth D.; Beardslee, William R.

2015-01-01

Child maltreatment is a preventable public health problem. Research has demonstrated that neighborhood structural factors (e.g. poverty, crime) can influence the proportion of a neighborhood’s children who are victims of maltreatment. A newer strategy is the identification of potentially modifiable social processes at the neighborhood level that can also influence maltreatment. Toward this end, this study examines neighborhood-level data (maltreatment cases substantiated by Illinois’ child protection agency, 1995–2005, social processes measured by the Project on Human Development in Chicago Neighborhoods, U.S. Census data, proportions of neighborhoods on public assistance, and crime data) that were linked across clusters of contiguous, relatively homogenous Chicago, IL census tracts with respect to racial/ethnic and socioeconomic composition. Our analysis—an ecological-level, repeated cross-sectional design utilizing random-intercept logit models— with a sensitivity analysis using spatial models to control for spatial autocorrelation – revealed consistent associations between neighborhood social processes and maltreatment. Neighborhoods higher in collective efficacy, intergenerational closure, and social networks, and lower in disorder had lower proportions of neglect, physical abuse, and sexual abuse substantiated cases, controlling for differences in structural factors. Higher collective efficacy and social network size also predicted a lower proportion of substance-exposed infants. This research indicates that strategies to mobilize neighborhood-level protective factors may decrease child maltreatment more effectively than individual and family-focused efforts alone. PMID:26684963

Neighborhood-level social processes and substantiated cases of child maltreatment.

PubMed

Molnar, Beth E; Goerge, Robert M; Gilsanz, Paola; Hill, Andrea; Subramanian, S V; Holton, John K; Duncan, Dustin T; Beatriz, Elizabeth D; Beardslee, William R

2016-01-01

Child maltreatment is a preventable public health problem. Research has demonstrated that neighborhood structural factors (e.g. poverty, crime) can influence the proportion of a neighborhood's children who are victims of maltreatment. A newer strategy is the identification of potentially modifiable social processes at the neighborhood level that can also influence maltreatment. Toward this end, this study examines neighborhood-level data (maltreatment cases substantiated by Illinois' child protection agency, 1995-2005, social processes measured by the Project on Human Development in Chicago Neighborhoods, U.S. Census data, proportions of neighborhoods on public assistance, and crime data) that were linked across clusters of contiguous, relatively homogenous Chicago, IL census tracts with respect to racial/ethnic and socioeconomic composition. Our analysis-an ecological-level, repeated cross-sectional design utilizing random-intercept logit models-with a sensitivity analysis using spatial models to control for spatial autocorrelation-revealed consistent associations between neighborhood social processes and maltreatment. Neighborhoods higher in collective efficacy, intergenerational closure, and social networks, and lower in disorder had lower proportions of neglect, physical abuse, and sexual abuse substantiated cases, controlling for differences in structural factors. Higher collective efficacy and social network size also predicted a lower proportion of substance-exposed infants. This research indicates that strategies to mobilize neighborhood-level protective factors may decrease child maltreatment more effectively than individual and family-focused efforts alone. Copyright © 2015 Elsevier Ltd. All rights reserved.

Analysis and evaluation in the production process and equipment area of the low-cost solar array project

NASA Technical Reports Server (NTRS)

Wolf, M.

1982-01-01

It was found that the Solarex metallization design and process selection should be modified to yield substantially higher output of the 10 cm x 10 cm cells, while the Westinghouse design is extremely close to the optimum. In addition, further attention to the Solarex pn junction and base high/low junction formation processes could be beneficial. For the future efficiency improvement, it was found that refinement of the various minority carrier lifetime measurement methods is needed, as well as considerably increased sophistication in the interpretation of the results of these methods. In addition, it was determined that further experimental investigation of the Auger lifetime is needed, to conclusively determine the Auger coefficients for the direct Auger recombination at high majority carrier concentrations.

A mature Bosch CO2 reduction technology. [for long-duration space missions

NASA Technical Reports Server (NTRS)

King, C. D.; Holmes, R. F.

1976-01-01

The reduction of CO2 is one of the steps in closing the oxygen loop for long-duration manned space missions. Several units utilizing the Bosch process, which catalytically reduces CO2 with hydrogen, have been built and operated during the past decade. Each contributed substantial information affecting subsequent designs. Early challenges were primarily concerned with carbon control, materials durability, and reliability of reaction initiation. These were followed by concern about power consumption, expendable weight, volume, and process rate control. Suitable materials and techniques for carbon containment and process reliability have been demonstrated. Power requirements have been reduced by almost an order of magnitude. Methods for significant reductions in expendable weight and volume have been developed. The technology is at a state of maturity directly applicable to designs for space missions.

Standard work for room entry: Linking lean, hand hygiene, and patient-centeredness.

PubMed

O'Reilly, Kristin; Ruokis, Samantha; Russell, Kristin; Teves, Tim; DiLibero, Justin; Yassa, David; Berry, Hannah; Howell, Michael D

2016-03-01

Healthcare-associated infections are costly and fatal. Substantial front-line, administrative, regulatory, and research efforts have focused on improving hand hygiene. While broad agreement exists that hand hygiene is the most important single approach to infection prevention, compliance with hand hygiene is typically only about 40%(1). Our aim was to develop a standard process for room entry in the intensive care unit that improved compliance with hand hygiene and allowed for maximum efficiency. We recognized that hand hygiene is a single step in a substantially more complicated process of room entry. We applied Lean engineering techniques to develop a standard process that included both physical steps and also standard communication elements from provider to patients and families and created a physical environment to support this. We observed meaningful improvement in the performance of the new standard as well as time savings for clinical providers with each room entry. We also observed an increase in room entries that included verbal communication and an explanation of what the clinician was entering the room to do. The design and implementation of a standardized room entry process and the creation of an environment that supports that new process has resulted in measurable positive outcomes on the medical intensive care unit, including quality, patient experience, efficiency, and staff satisfaction. Designing a process, rather than viewing tasks that need to happen in close proximity in time (either serially or in parallel) as unrelated, simplifies work for staff and results in higher compliance to individual tasks. Copyright © 2015 Elsevier Inc. All rights reserved.

Designing forward with an eye to the past: Morphogenesis of the lower Yuba River

NASA Astrophysics Data System (ADS)

James, L. Allan

2015-12-01

The early geomorphic evolution of the lower Yuba River (LYR), northern California, up to 1906 is reconstructed using cartographic, documentary, topographic, and stratigraphic evidence. The importance of early river mining is identified along with rates and patterns of floodplain aggradation and channel incision at the turn of the 20th century. The LYR is a classic example of anthropogeomorphic transformation of a river by episodic hydraulic mining sedimentation. This was followed by channelization, damming, dredging, and other engineering works to redirect, contain, and stabilize channels. These geomorphic changes and engineering controls continue to govern channel and floodplain form and process, control the trajectory of river responses, and constrain flood control, water quality, and aquatic ecosystem management options. Returning a river system to a prior condition should not be the primary goal of river rehabilitation projects, especially if hydrologic inputs have substantially changed. Reconstructing former conditions may be impractical and unsustainable under modern circumstances. Instead, fluvial systems should be designed and managed for present inputs and processes while anticipating future conditions. Rapid changes in land use and climate that generate changes in runoff and sediment loadings are likely to generate morphological instability, and these changes should be considered in the design and management of fluvial systems. The past geomorphic evolution of fluvial systems should also be considered in design and management decisions to recognize trajectories and suppressed tendencies. Recognition of trends and system vulnerabilities may avoid potential blunders, such as removing critical stabilizing works. Complex causalities may be difficult to reconstruct from geomorphic form alone, however, due to process-form dynamics. Detailed research on the geomorphic and engineering history of a river is essential, therefore, if substantial changes and morphologic instabilities have occurred.

Laser process and corresponding structures for fabrication of solar cells with shunt prevention dielectric

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harley, Gabriel; Smith, David D.; Dennis, Tim

Contact holes of solar cells are formed by laser ablation to accommodate various solar cell designs. Use of a laser to form the contact holes is facilitated by replacing films formed on the diffusion regions with a film that has substantially uniform thickness. Contact holes may be formed to deep diffusion regions to increase the laser ablation process margins. The laser configuration may be tailored to form contact holes through dielectric films of varying thicknesses.

Process and structures for fabrication of solar cells with laser ablation steps to form contact holes

DOEpatents

Harley, Gabriel; Smith, David D; Dennis, Tim; Waldhauer, Ann; Kim, Taeseok; Cousins, Peter John

2013-11-19

Contact holes of solar cells are formed by laser ablation to accomodate various solar cell designs. Use of a laser to form the contact holes is facilitated by replacing films formed on the diffusion regions with a film that has substantially uniform thickness. Contact holes may be formed to deep diffusion regions to increase the laser ablation process margins. The laser configuration may be tailored to form contact holes through dielectric films of varying thickness.

Research environments that promote integrity.

PubMed

Jeffers, Brenda Recchia; Whittemore, Robin

2005-01-01

The body of empirical knowledge about research integrity and the factors that promote research integrity in nursing research environments remains small. To propose an internal control model as an innovative framework for the design and structure of nursing research environments that promote integrity. An internal control model is adapted to illustrate its use for conceptualizing and designing research environments that promote integrity. The internal control model integrates both the organizational elements necessary to promote research integrity and the processes needed to assess research environments. The model provides five interrelated process components within which any number of research integrity variables and processes may be used and studied: internal control environment, risk assessment, internal control activities, monitoring, and information and communication. The components of the proposed research integrity internal control model proposed comprise an integrated conceptualization of the processes that provide reasonable assurance that research integrity will be promoted within the nursing research environment. Schools of nursing can use the model to design, implement, and evaluate systems that promote research integrity. The model process components need further exploration to substantiate the use of the model in nursing research environments.

Design, construction and performance of a portable handheld electrohydrodynamic multi-needle spray gun for biomedical applications.

PubMed

Sofokleous, Panagiotis; Stride, Eleanor; Bonfield, William; Edirisinghe, Mohan

2013-01-01

Electrohydrodynamic (EHD) processing has attracted substantial interest in the technological and pharmaceutical sectors in recent years. Given the complexity of the process, exploring new ideas for EHD electrospraying and electrospinning delivery is a challenge. In this article, the design, construction and testing of a portable handheld EHD multi-needle device are described to produce multifunctional particles and fibers. Solid and encapsulated polymer particles and fibers were generated in order to study the performance of the device. The intrinsic properties of the feed solution/suspension and the processing conditions were adjusted to ensure robustness of the process and give uniform and reproducible products, with diameters ranging from the sub-micrometer scale to a few micrometers. These products have a broad range of applications in many advanced industrial sectors e.g. drug delivery systems, wound dressing patches, low calorie food products and cosmetics. Copyright © 2012 Elsevier B.V. All rights reserved.

Digging Up: A Five-Year Journey to Instructional-Design Stability in a Postsecondary Distance Education Unit

ERIC Educational Resources Information Center

Epp, Jordan; McKee, Jeanette

2015-01-01

This report of practice describes a five-year process to establish and implement quality standards for a substantial portfolio of distance delivered courses at the Centre for Continuing and Distance Education, University of Saskatchewan. The report describes an analysis of the issues and the solutions found that led to our current curriculum…

Real-Time, Polyphase-FFT, 640-MHz Spectrum Analyzer

NASA Technical Reports Server (NTRS)

Zimmerman, George A.; Garyantes, Michael F.; Grimm, Michael J.; Charny, Bentsian; Brown, Randy D.; Wilck, Helmut C.

1994-01-01

Real-time polyphase-fast-Fourier-transform, polyphase-FFT, spectrum analyzer designed to aid in detection of multigigahertz radio signals in two 320-MHz-wide polarization channels. Spectrum analyzer divides total spectrum of 640 MHz into 33,554,432 frequency channels of about 20 Hz each. Size and cost of polyphase-coefficient memory substantially reduced and much of processing loss of windowed FFTs eliminated.

Improving Teacher Selection: The Effect of Inter-Rater Reliability in the Screening Process. CEDR Working Paper. WP #2015-7

ERIC Educational Resources Information Center

Martinkova, Patricia; Goldhaber, Dan

2015-01-01

Inter-rater reliability, commonly assessed by intra-class correlation coefficient ICC, is an important index for describing the extent to which there is consistency amongst two or more raters in assigned measures. In organizational research, the data structure is often hierarchical and designs deviate substantially from the ideal of a balanced…

Deployment of e-health services - a business model engineering strategy.

PubMed

Kijl, Björn; Nieuwenhuis, Lambert J M; Huis in 't Veld, Rianne M H A; Hermens, Hermie J; Vollenbroek-Hutten, Miriam M R

2010-01-01

We designed a business model for deploying a myofeedback-based teletreatment service. An iterative and combined qualitative and quantitative action design approach was used for developing the business model and the related value network. Insights from surveys, desk research, expert interviews, workshops and quantitative modelling were combined to produce the first business model and then to refine it in three design cycles. The business model engineering strategy provided important insights which led to an improved, more viable and feasible business model and related value network design. Based on this experience, we conclude that the process of early stage business model engineering reduces risk and produces substantial savings in costs and resources related to service deployment.

Object-oriented design and programming in medical decision support.

PubMed

Heathfield, H; Armstrong, J; Kirkham, N

1991-12-01

The concept of object-oriented design and programming has recently received a great deal of attention from the software engineering community. This paper highlights the realisable benefits of using the object-oriented approach in the design and development of clinical decision support systems. These systems seek to build a computational model of some problem domain and therefore tend to be exploratory in nature. Conventional procedural design techniques do not support either the process of model building or rapid prototyping. The central concepts of the object-oriented paradigm are introduced, namely encapsulation, inheritance and polymorphism, and their use illustrated in a case study, taken from the domain of breast histopathology. In particular, the dual roles of inheritance in object-oriented programming are examined, i.e., inheritance as a conceptual modelling tool and inheritance as a code reuse mechanism. It is argued that the use of the former is not entirely intuitive and may be difficult to incorporate into the design process. However, inheritance as a means of optimising code reuse offers substantial technical benefits.

What makes a good home-based nocturnal seizure detector? A value sensitive design.

PubMed

van Andel, Judith; Leijten, Frans; van Delden, Hans; van Thiel, Ghislaine

2015-01-01

A device for the in-home detection of nocturnal seizures is currently being developed in the Netherlands, to improve care for patients with severe epilepsy. It is recognized that the design of medical technology is not value neutral: perspectives of users and developers are influential in design, and design choices influence these perspectives. However, during development processes, these influences are generally ignored and value-related choices remain implicit and poorly argued for. In the development process of the seizure detector we aimed to take values of all stakeholders into consideration. Therefore, we performed a parallel ethics study, using "value sensitive design." Analysis of stakeholder communication (in meetings and e-mail messages) identified five important values, namely, health, trust, autonomy, accessibility, and reliability. Stakeholders were then asked to give feedback on the choice of these values and how they should be interpreted. In a next step, the values were related to design choices relevant for the device, and then the consequences (risks and benefits) of these choices were investigated. Currently the process of design and testing of the device is still ongoing. The device will be validated in a trial in which the identified consequences of design choices are measured as secondary endpoints. Value sensitive design methodology is feasible for the development of new medical technology and can help designers substantiate the choices in their design.

Low-Cost Behavioral Nudges Increase Medicaid Take-Up Among Eligible Residents Of Oregon.

PubMed

Wright, Bill J; Garcia-Alexander, Ginny; Weller, Margarette A; Baicker, Katherine

2017-05-01

Efforts to reduce the ranks of the uninsured hinge on take-up of available programs and subsidies, but take-up of even free insurance is often less than complete. The evidence of the effectiveness of policies aiming to increase take-up is limited. We used a randomized controlled design to evaluate the impact of improved communication and behaviorally informed "nudges" designed to increase Medicaid take-up among eligible populations. Fielding randomized interventions in two different study populations in Oregon, we found that even very low-cost interventions substantially increased enrollment. Effects were larger in a population whose members had already expressed interest in obtaining coverage, but the effects were more persistent in low-income populations whose members were already enrolled in other state assistance programs but had not expressed interest in health insurance. The effects were similar across different demographic groups. Our results suggest that improving the design of enrollment processes and using low-cost mass-outreach efforts have the potential to substantially increase insurance coverage of vulnerable populations. Project HOPE—The People-to-People Health Foundation, Inc.

Status report on GELNG (gelled LNG)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rudnicki, M.; Hoffman, L.C.; Vander Wall, E.M.

1980-01-01

Over the past 2 years, Aerojet's research on characterizing the process, flow, and use properties of gelled LNG has covered (1) its safety-enhancement potential, (2) the economics and preliminary design of an industrial-scale gelation system, and (3) the design of a portable gelator for larger scale (40 m/sup 3/) spill tests. The technical results thus far continue to support the conclusion that GELNG would substantially reduce spill hazards. Operating parameters would not be significantly changed by gelation, and the cost impact on delivered LNG appears to be small (about 5%).

Engineering design: A powerful influence on the business success on manufacturing industry

NASA Astrophysics Data System (ADS)

Coplin, John F.

1990-08-01

Engineering design, one of the most powerful forces in producing a package which matches market need, is discussed. It is essentially a detailed planning process backed by analysis and demonstration. The need for innovation to achieve competitive edge and profitability is considered. Innovation contains risk which must be controlled before substantial investment is made. The high rate of change of technology gives rise to the need for good training and retraining. Benefits which offsets costs at the time of occurring that cost are reached.

Design-Filter Selection for H2 Control of Microgravity Isolation Systems: A Single-Degree-of-Freedom Case Study

NASA Technical Reports Server (NTRS)

Hampton, R. David; Whorton, Mark S.

2000-01-01

Many microgravity space-science experiments require active vibration isolation, to attain suitably low levels of background acceleration for useful experimental results. The design of state-space controllers by optimal control methods requires judicious choices of frequency-weighting design filters. Kinematic coupling among states greatly clouds designer intuition in the choices of these filters, and the masking effects of the state observations cloud the process further. Recent research into the practical application of H2 synthesis methods to such problems, indicates that certain steps can lead to state frequency-weighting design-filter choices with substantially improved promise of usefulness, even in the face of these difficulties. In choosing these filters on the states, one considers their relationships to corresponding design filters on appropriate pseudo-sensitivity- and pseudo-complementary-sensitivity functions. This paper investigates the application of these considerations to a single-degree-of-freedom microgravity vibration-isolation test case. Significant observations that were noted during the design process are presented. along with explanations based on the existent theory for such problems.

The limited impact of indeterminacy for healthcare rationing: how indeterminacy problems show the need for a hybrid theory, but nothing more.

PubMed

Herlitz, Anders

2016-01-01

A notorious debate in the ethics of healthcare rationing concerns whether to address rationing decisions with substantial principles or with a procedural approach. One major argument in favour of procedural approaches is that substantial principles are indeterminate so that we can reasonably disagree about how to apply them. To deal with indeterminacy, we need a just decision process. In this paper I argue that it is a mistake to abandon substantial principles just because they are indeterminate. It is true that reasonable substantial principles designed to deal with healthcare rationing can be expected to be indeterminate. Yet, the indeterminacy is only partial. In some situations we can fully determine what to do in light of the principles, in some situations we cannot. The conclusion to draw from this fact is not that we need to develop procedural approaches to healthcare rationing, but rather that we need a more complex theory in which both substantial principles and procedural approaches are needed. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

A Electro-Optical Image Algebra Processing System for Automatic Target Recognition

NASA Astrophysics Data System (ADS)

Coffield, Patrick Cyrus

The proposed electro-optical image algebra processing system is designed specifically for image processing and other related computations. The design is a hybridization of an optical correlator and a massively paralleled, single instruction multiple data processor. The architecture of the design consists of three tightly coupled components: a spatial configuration processor (the optical analog portion), a weighting processor (digital), and an accumulation processor (digital). The systolic flow of data and image processing operations are directed by a control buffer and pipelined to each of the three processing components. The image processing operations are defined in terms of basic operations of an image algebra developed by the University of Florida. The algebra is capable of describing all common image-to-image transformations. The merit of this architectural design is how it implements the natural decomposition of algebraic functions into spatially distributed, point use operations. The effect of this particular decomposition allows convolution type operations to be computed strictly as a function of the number of elements in the template (mask, filter, etc.) instead of the number of picture elements in the image. Thus, a substantial increase in throughput is realized. The implementation of the proposed design may be accomplished in many ways. While a hybrid electro-optical implementation is of primary interest, the benefits and design issues of an all digital implementation are also discussed. The potential utility of this architectural design lies in its ability to control a large variety of the arithmetic and logic operations of the image algebra's generalized matrix product. The generalized matrix product is the most powerful fundamental operation in the algebra, thus allowing a wide range of applications. No other known device or design has made this claim of processing speed and general implementation of a heterogeneous image algebra.

The child's perspective as a guiding principle: Young children as co-designers in the design of an interactive application meant to facilitate participation in healthcare situations.

PubMed

Stålberg, Anna; Sandberg, Anette; Söderbäck, Maja; Larsson, Thomas

2016-06-01

During the last decade, interactive technology has entered mainstream society. Its many users also include children, even the youngest ones, who use the technology in different situations for both fun and learning. When designing technology for children, it is crucial to involve children in the process in order to arrive at an age-appropriate end product. In this study we describe the specific iterative process by which an interactive application was developed. This application is intended to facilitate young children's, three-to five years old, participation in healthcare situations. We also describe the specific contributions of the children, who tested the prototypes in a preschool, a primary health care clinic and an outpatient unit at a hospital, during the development process. The iterative phases enabled the children to be involved at different stages of the process and to evaluate modifications and improvements made after each prior iteration. The children contributed their own perspectives (the child's perspective) on the usability, content and graphic design of the application, substantially improving the software and resulting in an age-appropriate product. Copyright © 2016 Elsevier Inc. All rights reserved.

14 CFR 21.97 - Approval of major changes in type design.

Code of Federal Regulations, 2010 CFR

2010-01-01

... must submit substantiating data and necessary descriptive data for inclusion in the type design. (b... major change in type design must— (1) Provide substantiating data and necessary descriptive data for... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Approval of major changes in type design...

How work context affects operating room processes: using data mining and computer simulation to analyze facility and process design.

PubMed

Baumgart, André; Denz, Christof; Bender, Hans-Joachim; Schleppers, Alexander

2009-01-01

The complexity of the operating room (OR) requires that both structural (eg, department layout) and behavioral (eg, staff interactions) patterns of work be considered when developing quality improvement strategies. In our study, we investigated how these contextual factors influence outpatient OR processes and the quality of care delivered. The study setting was a German university-affiliated hospital performing approximately 6000 outpatient surgeries annually. During the 3-year-study period, the hospital significantly changed its outpatient OR facility layout from a decentralized (ie, ORs in adjacent areas of the building) to a centralized (ie, ORs in immediate vicinity of each other) design. To study the impact of the facility change on OR processes, we used a mixed methods approach, including process analysis, process modeling, and social network analysis of staff interactions. The change in facility layout was seen to influence OR processes in ways that could substantially affect patient outcomes. For example, we found a potential for more errors during handovers in the new centralized design due to greater interdependency between tasks and staff. Utilization of the mixed methods approach in our analysis, as compared with that of a single assessment method, enabled a deeper understanding of the OR work context and its influence on outpatient OR processes.

Hydrocarbonaceous material processing methods and apparatus

DOEpatents

Brecher, Lee E [Laramie, WY

2011-07-12

Methods and apparatus are disclosed for possibly producing pipeline-ready heavy oil from substantially non-pumpable oil feeds. The methods and apparatus may be designed to produce such pipeline-ready heavy oils in the production field. Such methods and apparatus may involve thermal soaking of liquid hydrocarbonaceous inputs in thermal environments (2) to generate, though chemical reaction, an increased distillate amount as compared with conventional boiling technologies.

Reliable Early Classification on Multivariate Time Series with Numerical and Categorical Attributes

DTIC Science & Technology

2015-05-22

design a procedure of feature extraction in REACT named MEG (Mining Equivalence classes with shapelet Generators) based on the concept of...Equivalence Classes Mining [12, 15]. MEG can efficiently and effectively generate the discriminative features. In addition, several strategies are proposed...technique of parallel computing [4] to propose a process of pa- rallel MEG for substantially reducing the computational overhead of discovering shapelet

Design of components for growing higher plants in space

NASA Technical Reports Server (NTRS)

1988-01-01

The overall goal of this project is to design unique systems and components for growing higher plants in microgravity during long-term space missions (Mars and beyond). Specific design tasks were chosen to contribute to and supplement NASA's Controlled Ecological Life Support System (CELSS) project. Selected tasks were automated seeding of plants, plant health sensing, and food processing. Prototype systems for planting both germinated and nongerminated seeds were fabricated and tested. Water and air pressure differences and electrostatic fields were used to trap seeds for separation and transport for planting. An absorption spectrometer was developed to measure chlorophyll levels in plants as an early warning of plant health problems. In the area of food processing, a milling system was created using high-speed rotating blades which were aerodynamically configured to produce circulation and retractable to prevent leakage. The project produced significant results having substantial benefit to NASA. It also provided an outstanding learning experience for the students involved.

Plug and Process Loads Capacity and Power Requirements Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheppy, M.; Gentile-Polese, L.

2014-09-01

This report addresses gaps in actionable knowledge that would help reduce the plug load capacities designed into buildings. Prospective building occupants and real estate brokers lack accurate references for plug and process load (PPL) capacity requirements, so they often request 5-10 W/ft2 in their lease agreements. Limited initial data, however, suggest that actual PPL densities in leased buildings are substantially lower. Overestimating PPL capacity leads designers to oversize electrical infrastructure and cooling systems. Better guidance will enable improved sizing and design of these systems, decrease upfront capital costs, and allow systems to operate more energy efficiently. The main focus ofmore » this report is to provide industry with reliable, objective third-party guidance to address the information gap in typical PPL densities for commercial building tenants. This could drive changes in negotiations about PPL energy demands.« less

IpexT: Integrated Planning and Execution for Military Satellite Tele-Communications

NASA Technical Reports Server (NTRS)

Plaunt, Christian; Rajan, Kanna

2004-01-01

The next generation of military communications satellites may be designed as a fast packet-switched constellation of spacecraft able to withstand substantial bandwidth capacity fluctuation in the face of dynamic resource utilization and rapid environmental changes including jamming of communication frequencies and unstable weather phenomena. We are in the process of designing an integrated scheduling and execution tool which will aid in the analysis of the design parameters needed for building such a distributed system for nominal and battlefield communications. This paper discusses the design of such a system based on a temporal constraint posting planner/scheduler and a smart executive which can cope with a dynamic environment to make a more optimal utilization of bandwidth than the current circuit switched based approach.

Field-Distortion Air-Insulated Switches for Next-Generation Pulsed-Power Accelerators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wisher, Matthew Louis; Johns, Owen M.; Breden, Eric Wayne

We have developed two advanced designs of a field-distortion air-insulated spark-gap switch that reduce the size of a linear-transformer-driver (LTD) brick. Both designs operate at 200 kV and a peak current of ~50 kA. At these parameters, both achieve a jitter of less than 2 ns and a prefire rate of ~0.1% over 5000 shots. We have reduced the number of switch parts and assembly steps, which has resulted in a more uniform, design-driven assembly process. We will characterize the performance of tungsten-copper and graphite electrodes, and two different electrode geometries. The new switch designs will substantially improve the electricalmore » and operational performance of next-generation pulsed-power accelerators.« less

Influences of the manufacturing process chain design on the near surface condition and the resulting fatigue behaviour of quenched and tempered SAE 4140

NASA Astrophysics Data System (ADS)

Klein, M.; Eifler, D.

2010-07-01

To analyse interactions between single steps of process chains, variations in material properties, especially the microstructure and the resulting mechanical properties, specimens with tension screw geometry were manufactured with five process chains. The different process chains as well as their parameters influence the near surface condition and consequently the fatigue behaviour in a characteristic manner. The cyclic deformation behaviour of these specimens can be benchmarked equivalently with conventional strain measurements as well as with high-precision temperature and electrical resistance measurements. The development of temperature-values provides substantial information on cyclic load dependent changes in the microstructure.

Innovative vitrification for soil remediation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jetta, N.W.; Patten, J.S.; Hart, J.G.

1995-12-01

The objective of this DOE demonstration program is to validate the performance and operation of the Vortec Cyclone Melting System (CMS{trademark}) for the processing of LLW contaminated soils found at DOE sites. This DOE vitrification demonstration project has successfully progressed through the first two phases. Phase 1 consisted of pilot scale testing with surrogate wastes and the conceptual design of a process plant operating at a generic DOE site. The objective of Phase 2, which is scheduled to be completed the end of FY 95, is to develop a definitive process plant design for the treatment of wastes at amore » specific DOE facility. During Phase 2, a site specific design was developed for the processing of LLW soils and muds containing TSCA organics and RCRA metal contaminants. Phase 3 will consist of a full scale demonstration at the DOE gaseous diffusion plant located in Paducah, KY. Several DOE sites were evaluated for potential application of the technology. Paducah was selected for the demonstration program because of their urgent waste remediation needs as well as their strong management and cost sharing financial support for the project. During Phase 2, the basic nitrification process design was modified to meet the specific needs of the new waste streams available at Paducah. The system design developed for Paducah has significantly enhanced the processing capabilities of the Vortec vitrification process. The overall system design now includes the capability to shred entire drums and drum packs containing mud, concrete, plastics and PCB`s as well as bulk waste materials. This enhanced processing capability will substantially expand the total DOE waste remediation applications of the technology.« less

An Approach to the Constrained Design of Natural Laminar Flow Airfoils

NASA Technical Reports Server (NTRS)

Green, Bradford E.

1997-01-01

A design method has been developed by which an airfoil with a substantial amount of natural laminar flow can be designed, while maintaining other aerodynamic and geometric constraints. After obtaining the initial airfoil's pressure distribution at the design lift coefficient using an Euler solver coupled with an integral turbulent boundary layer method, the calculations from a laminar boundary layer solver are used by a stability analysis code to obtain estimates of the transition location (using N-Factors) for the starting airfoil. A new design method then calculates a target pressure distribution that will increase the laminar flow toward the desired amount. An airfoil design method is then iteratively used to design an airfoil that possesses that target pressure distribution. The new airfoil's boundary layer stability characteristics are determined, and this iterative process continues until an airfoil is designed that meets the laminar flow requirement and as many of the other constraints as possible.

An approach to the constrained design of natural laminar flow airfoils

NASA Technical Reports Server (NTRS)

Green, Bradford Earl

1995-01-01

A design method has been developed by which an airfoil with a substantial amount of natural laminar flow can be designed, while maintaining other aerodynamic and geometric constraints. After obtaining the initial airfoil's pressure distribution at the design lift coefficient using an Euler solver coupled with an integml turbulent boundary layer method, the calculations from a laminar boundary layer solver are used by a stability analysis code to obtain estimates of the transition location (using N-Factors) for the starting airfoil. A new design method then calculates a target pressure distribution that will increase the larninar flow toward the desired amounl An airfoil design method is then iteratively used to design an airfoil that possesses that target pressure distribution. The new airfoil's boundary layer stability characteristics are determined, and this iterative process continues until an airfoil is designed that meets the laminar flow requirement and as many of the other constraints as possible.

Nitrous oxide emissions from wastewater treatment processes

PubMed Central

Law, Yingyu; Ye, Liu; Pan, Yuting; Yuan, Zhiguo

2012-01-01

Nitrous oxide (N2O) emissions from wastewater treatment plants vary substantially between plants, ranging from negligible to substantial (a few per cent of the total nitrogen load), probably because of different designs and operational conditions. In general, plants that achieve high levels of nitrogen removal emit less N2O, indicating that no compromise is required between high water quality and lower N2O emissions. N2O emissions primarily occur in aerated zones/compartments/periods owing to active stripping, and ammonia-oxidizing bacteria, rather than heterotrophic denitrifiers, are the main contributors. However, the detailed mechanisms remain to be fully elucidated, despite strong evidence suggesting that both nitrifier denitrification and the chemical breakdown of intermediates of hydroxylamine oxidation are probably involved. With increased understanding of the fundamental reactions responsible for N2O production in wastewater treatment systems and the conditions that stimulate their occurrence, reduction of N2O emissions from wastewater treatment systems through improved plant design and operation will be achieved in the near future. PMID:22451112

Co-design of software and hardware to implement remote sensing algorithms

NASA Astrophysics Data System (ADS)

Theiler, James P.; Frigo, Janette R.; Gokhale, Maya; Szymanski, John J.

2002-01-01

Both for offline searches through large data archives and for onboard computation at the sensor head, there is a growing need for ever-more rapid processing of remote sensing data. For many algorithms of use in remote sensing, the bulk of the processing takes place in an ``inner loop'' with a large number of simple operations. For these algorithms, dramatic speedups can often be obtained with specialized hardware. The difficulty and expense of digital design continues to limit applicability of this approach, but the development of new design tools is making this approach more feasible, and some notable successes have been reported. On the other hand, it is often the case that processing can also be accelerated by adopting a more sophisticated algorithm design. Unfortunately, a more sophisticated algorithm is much harder to implement in hardware, so these approaches are often at odds with each other. With careful planning, however, it is sometimes possible to combine software and hardware design in such a way that each complements the other, and the final implementation achieves speedup that would not have been possible with a hardware-only or a software-only solution. We will in particular discuss the co-design of software and hardware to achieve substantial speedup of algorithms for multispectral image segmentation and for endmember identification.

Acoustic Source Localization via Time Difference of Arrival Estimation for Distributed Sensor Networks Using Tera-Scale Optical Core Devices

DOE PAGES

Imam, Neena; Barhen, Jacob

2009-01-01

For real-time acoustic source localization applications, one of the primary challenges is the considerable growth in computational complexity associated with the emergence of ever larger, active or passive, distributed sensor networks. These sensors rely heavily on battery-operated system components to achieve highly functional automation in signal and information processing. In order to keep communication requirements minimal, it is desirable to perform as much processing on the receiver platforms as possible. However, the complexity of the calculations needed to achieve accurate source localization increases dramatically with the size of sensor arrays, resulting in substantial growth of computational requirements that cannot bemore » readily met with standard hardware. One option to meet this challenge builds upon the emergence of digital optical-core devices. The objective of this work was to explore the implementation of key building block algorithms used in underwater source localization on the optical-core digital processing platform recently introduced by Lenslet Inc. This demonstration of considerably faster signal processing capability should be of substantial significance to the design and innovation of future generations of distributed sensor networks.« less

Off-Line Quality Control In Integrated Circuit Fabrication Using Experimental Design

NASA Astrophysics Data System (ADS)

Phadke, M. S.; Kackar, R. N.; Speeney, D. V.; Grieco, M. J.

1987-04-01

Off-line quality control is a systematic method of optimizing production processes and product designs. It is widely used in Japan to produce high quality products at low cost. The method was introduced to us by Professor Genichi Taguchi who is a Deming-award winner and a former Director of the Japanese Academy of Quality. In this paper we will i) describe the off-line quality control method, and ii) document our efforts to optimize the process for forming contact windows in 3.5 Aim CMOS circuits fabricated in the Murray Hill Integrated Circuit Design Capability Laboratory. In the fabrication of integrated circuits it is critically important to produce contact windows of size very near the target dimension. Windows which are too small or too large lead to loss of yield. The off-line quality control method has improved both the process quality and productivity. The variance of the window size has been reduced by a factor of four. Also, processing time for window photolithography has been substantially reduced. The key steps of off-line quality control are: i) Identify important manipulatable process factors and their potential working levels. ii) Perform fractional factorial experiments on the process using orthogonal array designs. iii) Analyze the resulting data to determine the optimum operating levels of the factors. Both the process mean and the process variance are considered in this analysis. iv) Conduct an additional experiment to verify that the new factor levels indeed give an improvement.

Design Process for High Speed Civil Transport Aircraft Improved by Neural Network and Regression Methods

NASA Technical Reports Server (NTRS)

Hopkins, Dale A.

1998-01-01

A key challenge in designing the new High Speed Civil Transport (HSCT) aircraft is determining a good match between the airframe and engine. Multidisciplinary design optimization can be used to solve the problem by adjusting parameters of both the engine and the airframe. Earlier, an example problem was presented of an HSCT aircraft with four mixed-flow turbofan engines and a baseline mission to carry 305 passengers 5000 nautical miles at a cruise speed of Mach 2.4. The problem was solved by coupling NASA Lewis Research Center's design optimization testbed (COMETBOARDS) with NASA Langley Research Center's Flight Optimization System (FLOPS). The computing time expended in solving the problem was substantial, and the instability of the FLOPS analyzer at certain design points caused difficulties. In an attempt to alleviate both of these limitations, we explored the use of two approximation concepts in the design optimization process. The two concepts, which are based on neural network and linear regression approximation, provide the reanalysis capability and design sensitivity analysis information required for the optimization process. The HSCT aircraft optimization problem was solved by using three alternate approaches; that is, the original FLOPS analyzer and two approximate (derived) analyzers. The approximate analyzers were calibrated and used in three different ranges of the design variables; narrow (interpolated), standard, and wide (extrapolated).

A Holistic Approach to Networked Information Systems Design and Analysis

DTIC Science & Technology

2016-04-15

attain quite substantial savings. 11. Optimal algorithms for energy harvesting in wireless networks. We use a Markov- decision-process (MDP) based...approach to obtain optimal policies for transmissions . The key advantage of our approach is that it holistically considers information and energy in a...Coding technique to minimize delays and the number of transmissions in Wireless Systems. As we approach an era of ubiquitous computing with information

Development of an Efficient Micro-Heat Exchanger: The Integration of Design Processing and Testing

DTIC Science & Technology

2005-11-01

together at high temperatures and cooled to room temperature. Additionally, alumina and zirconia powders have a major difference in densification...efficient heat exchanger. The main problem that needed to be resolved was the fact that the zirconia powders shrink much more than alumina powder...been measured. Our measurement in dimensions verifies that zirconia powders shrink substantially more than alumina powder except CR-15 after final

Measurements and TCAD simulation of novel ATLAS planar pixel detector structures for the HL-LHC upgrade

NASA Astrophysics Data System (ADS)

Nellist, C.; Dinu, N.; Gkougkousis, E.; Lounis, A.

2015-06-01

The LHC accelerator complex will be upgraded between 2020-2022, to the High-Luminosity-LHC, to considerably increase statistics for the various physics analyses. To operate under these challenging new conditions, and maintain excellent performance in track reconstruction and vertex location, the ATLAS pixel detector must be substantially upgraded and a full replacement is expected. Processing techniques for novel pixel designs are optimised through characterisation of test structures in a clean room and also through simulations with Technology Computer Aided Design (TCAD). A method to study non-perpendicular tracks through a pixel device is discussed. Comparison of TCAD simulations with Secondary Ion Mass Spectrometry (SIMS) measurements to investigate the doping profile of structures and validate the simulation process is also presented.

Snow as building material for construction of technological along-the-route roads of main pipelines

NASA Astrophysics Data System (ADS)

Merdanov, S. M.; Egorov, A. L.; Kostyrchenko, V. A.; Madyarov, T. M.

2018-05-01

The article deals with the process of compacting snow in a closed volume with the use of vacuum processing for the construction of technological along-the-route roads of main pipelines. The relevance of the chosen study is substantiated; methods and designs for snow compaction are considered. The publication activity and defenses of doctoral and candidate dissertations on the research subject are analyzed. Patent analysis of existing methods and equipment for snow compaction with indication of their disadvantages is carried out. A design calculation was carried out using computer programs in which a strength calculation was performed to identify the most stressed places in the construction of a vibrating hydraulic tyre-type roller. A 3D model of the experimental setup was developed.

Robust decentralized control laws for the ACES structure

NASA Technical Reports Server (NTRS)

Collins, Emmanuel G., Jr.; Phillips, Douglas J.; Hyland, David C.

1991-01-01

Control system design for the Active Control Technique Evaluation for Spacecraft (ACES) structure at NASA Marshall Space Flight Center is discussed. The primary objective of this experiment is to design controllers that provide substantial reduction of the line-of-sight pointing errors. Satisfaction of this objective requires the controllers to attenuate beam vibration significantly. The primary method chosen for control design is the optimal projection approach for uncertain systems (OPUS). The OPUS design process allows the simultaneous tradeoff of five fundamental issues in control design: actuator sizing, sensor accuracy, controller order, robustness, and system performance. A brief description of the basic ACES configuration is given. The development of the models used for control design and control design for eight system loops that were selected by analysis of test data collected from the structure are discussed. Experimental results showing that very significant performance improvement is achieved when all eight feedback loops are closed are presented.

Theoretical approaches to creation of robotic coal mines based on the synthesis of simulation technologies

NASA Astrophysics Data System (ADS)

Fryanov, V. N.; Pavlova, L. D.; Temlyantsev, M. V.

2017-09-01

Methodological approaches to theoretical substantiation of the structure and parameters of robotic coal mines are outlined. The results of mathematical and numerical modeling revealed the features of manifestation of geomechanical and gas dynamic processes in the conditions of robotic mines. Technological solutions for the design and manufacture of technical means for robotic mine are adopted using the method of economic and mathematical modeling and in accordance with the current regulatory documents. For a comparative performance evaluation of technological schemes of traditional and robotic mines, methods of cognitive modeling and matrix search for subsystem elements in the synthesis of a complex geotechnological system are applied. It is substantiated that the process of technical re-equipment of a traditional mine with a phased transition to a robotic mine will reduce unit costs by almost 1.5 times with a significant social effect due to a reduction in the number of personnel engaged in hazardous work.

DNA methylation-based classification of central nervous system tumours.

PubMed

Capper, David; Jones, David T W; Sill, Martin; Hovestadt, Volker; Schrimpf, Daniel; Sturm, Dominik; Koelsche, Christian; Sahm, Felix; Chavez, Lukas; Reuss, David E; Kratz, Annekathrin; Wefers, Annika K; Huang, Kristin; Pajtler, Kristian W; Schweizer, Leonille; Stichel, Damian; Olar, Adriana; Engel, Nils W; Lindenberg, Kerstin; Harter, Patrick N; Braczynski, Anne K; Plate, Karl H; Dohmen, Hildegard; Garvalov, Boyan K; Coras, Roland; Hölsken, Annett; Hewer, Ekkehard; Bewerunge-Hudler, Melanie; Schick, Matthias; Fischer, Roger; Beschorner, Rudi; Schittenhelm, Jens; Staszewski, Ori; Wani, Khalida; Varlet, Pascale; Pages, Melanie; Temming, Petra; Lohmann, Dietmar; Selt, Florian; Witt, Hendrik; Milde, Till; Witt, Olaf; Aronica, Eleonora; Giangaspero, Felice; Rushing, Elisabeth; Scheurlen, Wolfram; Geisenberger, Christoph; Rodriguez, Fausto J; Becker, Albert; Preusser, Matthias; Haberler, Christine; Bjerkvig, Rolf; Cryan, Jane; Farrell, Michael; Deckert, Martina; Hench, Jürgen; Frank, Stephan; Serrano, Jonathan; Kannan, Kasthuri; Tsirigos, Aristotelis; Brück, Wolfgang; Hofer, Silvia; Brehmer, Stefanie; Seiz-Rosenhagen, Marcel; Hänggi, Daniel; Hans, Volkmar; Rozsnoki, Stephanie; Hansford, Jordan R; Kohlhof, Patricia; Kristensen, Bjarne W; Lechner, Matt; Lopes, Beatriz; Mawrin, Christian; Ketter, Ralf; Kulozik, Andreas; Khatib, Ziad; Heppner, Frank; Koch, Arend; Jouvet, Anne; Keohane, Catherine; Mühleisen, Helmut; Mueller, Wolf; Pohl, Ute; Prinz, Marco; Benner, Axel; Zapatka, Marc; Gottardo, Nicholas G; Driever, Pablo Hernáiz; Kramm, Christof M; Müller, Hermann L; Rutkowski, Stefan; von Hoff, Katja; Frühwald, Michael C; Gnekow, Astrid; Fleischhack, Gudrun; Tippelt, Stephan; Calaminus, Gabriele; Monoranu, Camelia-Maria; Perry, Arie; Jones, Chris; Jacques, Thomas S; Radlwimmer, Bernhard; Gessi, Marco; Pietsch, Torsten; Schramm, Johannes; Schackert, Gabriele; Westphal, Manfred; Reifenberger, Guido; Wesseling, Pieter; Weller, Michael; Collins, Vincent Peter; Blümcke, Ingmar; Bendszus, Martin; Debus, Jürgen; Huang, Annie; Jabado, Nada; Northcott, Paul A; Paulus, Werner; Gajjar, Amar; Robinson, Giles W; Taylor, Michael D; Jaunmuktane, Zane; Ryzhova, Marina; Platten, Michael; Unterberg, Andreas; Wick, Wolfgang; Karajannis, Matthias A; Mittelbronn, Michel; Acker, Till; Hartmann, Christian; Aldape, Kenneth; Schüller, Ulrich; Buslei, Rolf; Lichter, Peter; Kool, Marcel; Herold-Mende, Christel; Ellison, David W; Hasselblatt, Martin; Snuderl, Matija; Brandner, Sebastian; Korshunov, Andrey; von Deimling, Andreas; Pfister, Stefan M

2018-03-22

Accurate pathological diagnosis is crucial for optimal management of patients with cancer. For the approximately 100 known tumour types of the central nervous system, standardization of the diagnostic process has been shown to be particularly challenging-with substantial inter-observer variability in the histopathological diagnosis of many tumour types. Here we present a comprehensive approach for the DNA methylation-based classification of central nervous system tumours across all entities and age groups, and demonstrate its application in a routine diagnostic setting. We show that the availability of this method may have a substantial impact on diagnostic precision compared to standard methods, resulting in a change of diagnosis in up to 12% of prospective cases. For broader accessibility, we have designed a free online classifier tool, the use of which does not require any additional onsite data processing. Our results provide a blueprint for the generation of machine-learning-based tumour classifiers across other cancer entities, with the potential to fundamentally transform tumour pathology.

High-performance image processing architecture

NASA Astrophysics Data System (ADS)

Coffield, Patrick C.

1992-04-01

The proposed architecture is a logical design specifically for image processing and other related computations. The design is a hybrid electro-optical concept consisting of three tightly coupled components: a spatial configuration processor (the optical analog portion), a weighting processor (digital), and an accumulation processor (digital). The systolic flow of data and image processing operations are directed by a control buffer and pipelined to each of the three processing components. The image processing operations are defined by an image algebra developed by the University of Florida. The algebra is capable of describing all common image-to-image transformations. The merit of this architectural design is how elegantly it handles the natural decomposition of algebraic functions into spatially distributed, point-wise operations. The effect of this particular decomposition allows convolution type operations to be computed strictly as a function of the number of elements in the template (mask, filter, etc.) instead of the number of picture elements in the image. Thus, a substantial increase in throughput is realized. The logical architecture may take any number of physical forms. While a hybrid electro-optical implementation is of primary interest, the benefits and design issues of an all digital implementation are also discussed. The potential utility of this architectural design lies in its ability to control all the arithmetic and logic operations of the image algebra's generalized matrix product. This is the most powerful fundamental formulation in the algebra, thus allowing a wide range of applications.

Optimizing product life cycle processes in design phase

NASA Astrophysics Data System (ADS)

Faneye, Ola. B.; Anderl, Reiner

2002-02-01

Life cycle concepts do not only serve as basis in assisting product developers understand the dependencies between products and their life cycles, they also help in identifying potential opportunities for improvement in products. Common traditional concepts focus mainly on energy and material flow across life phases, necessitating the availability of metrics derived from a reference product. Knowledge of life cycle processes won from an existing product is directly reused in its redesign. Depending on sales volume nevertheless, the environmental impact before product optimization can be substantial. With modern information technologies today, computer-aided life cycle methodologies can be applied well before product use. On the basis of a virtual prototype, life cycle processes are analyzed and optimized, using simulation techniques. This preventive approach does not only help in minimizing (or even eliminating) environmental burdens caused by product, costs incurred due to changes in real product can also be avoided. The paper highlights the relationship between product and life cycle and presents a computer-based methodology for optimizing the product life cycle during design, as presented by SFB 392: Design for Environment - Methods and Tools at Technical University, Darmstadt.

Loading an Equidistant Ion Chain in a Ring Shaped Surface Trap and Anomalous Heating Studies with a High Optical Access Trap

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tabakov, Boyan

2015-07-01

Microfabricated segmented surface ion traps are one viable avenue to scalable quantum information processing. At Sandia National Laboratories we design, fabricate, and characterize such traps. Our unique fabrication capabilities allow us to design traps that facilitate tasks beyond quantum information processing. The design and performance of a trap with a target capability of storing hundreds of equally spaced ions on a ring is described. Such a device could aid experimental studies of phenomena as diverse as Hawking radiation, quantum phase transitions, and the Aharonov - Bohm effect. The fabricated device is demonstrated to hold a ~ 400 ion circular crystal,more » with 9 μm average spacing between ions. The task is accomplished by first characterizing undesired electric fields in the trapping volume and then designing and applying an electric field that substantially reduces the undesired fields. In addition, experimental efforts are described to reduce the motional heating rates in a surface trap by low energy in situ argon plasma treatment that reduces the amount of surface contaminants. The experiment explores the premise that carbonaceous compounds present on the surface contribute to the anomalous heating of secular motion modes in surface traps. This is a research area of fundamental interest to the ion trapping community, as heating adversely affects coherence and thus gate fidelity. The device used provides high optical laser access, substantially reducing scatter from the surface, and thus charging that may lead to excess micromotion. Heating rates for different axial mode frequencies are compared before and after plasma treatment. The presence of a carbon source near the plasma prevents making a conclusion on the observed absence of change in heating rates.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kung, C C; Brunkhorst, C; Greenough, N

Experimental results have shown that the high harmonic fast wave (HHFW) at 30 MHz can provide substantial plasma heating and current drive for the NSTX spherical tokamak operation. However, the present antenna strap design rarely achieves the design goal of delivering the full transmitter capability of 6 MW to the plasma. In order to deliver more power to the plasma, a new antenna strap design and the associated coaxial line feeds are being constructed. This new antenna strap design features two feedthroughs to replace the old single feed-through design. In the design process, CST Microwave Studio has been used tomore » simulate the entire new antenna strap structure including the enclosure and the Faraday shield. In this paper, the antenna strap model and the simulation results will be discussed in detail. The test results from the new antenna straps with their associated resonant loops will be presented as well.« less

Program for establishing long-time flight service performance of composite materials in the center wing structure of C-130 aircraft. Phase 4: Ground/flight acceptance tests

NASA Technical Reports Server (NTRS)

Harvill, W. E.; Kizer, J. A.

1976-01-01

The advantageous structural uses of advanced filamentary composites are demonstrated by design, fabrication, and test of three boron-epoxy reinforced C-130 center wing boxes. The advanced development work necessary to support detailed design of a composite reinforced C-130 center wing box was conducted. Activities included the development of a basis for structural design, selection and verification of materials and processes, manufacturing and tooling development, and fabrication and test of full-scale portions of the center wing box. Detailed design drawings, and necessary analytical structural substantiation including static strength, fatigue endurance, flutter, and weight analyses are considered. Some additional component testing was conducted to verify the design for panel buckling, and to evaluate specific local design areas. Development of the cool tool restraint concept was completed, and bonding capabilities were evaluated using full-length skin panel and stringer specimens.

n-B-pi-p Superlattice Infrared Detector

NASA Technical Reports Server (NTRS)

Ting, David Z.; Bandara, Sumith V.; Hill, Cory J.; Gunapala, Sarath D.

2011-01-01

A specially designed barrier (B) is inserted at the n-pi junction [where most GR (generation-recombination) processes take place] in the standard n-pi-p structure to substantially reduce generation-recombination dark currents. The resulting n-Bpi- p structure also has reduced tunneling dark currents, thereby solving some of the limitations to which current type II strained layer superlattice infrared detectors are prone. This innovation is compatible with common read-out integrated circuits (ROICs).

Removal of dissolved and colloidal silica

DOEpatents

Midkiff, William S.

2002-01-01

Small amorphous silica particles are used to provide a relatively large surface area upon which silica will preferentially adsorb, thereby preventing or substantially reducing scaling caused by deposition of silica on evaporative cooling tower components, especially heat exchange surfaces. The silica spheres are contacted by the cooling tower water in a sidestream reactor, then separated using gravity separation, microfiltration, vacuum filtration, or other suitable separation technology. Cooling tower modifications for implementing the invention process have been designed.

Active chatter suppression with displacement-only measurement in turning process

NASA Astrophysics Data System (ADS)

Ma, Haifeng; Wu, Jianhua; Yang, Liuqing; Xiong, Zhenhua

2017-08-01

Regenerative chatter is a major hindrance for achieving high quality and high production rate in machining processes. Various active controllers have been proposed to mitigate chatter. However, most of existing controllers were developed on the basis of multi-states feedback of the system and state observers were usually needed. Moreover, model parameters of the machining process (mass, damping and stiffness) were required in existing active controllers. In this study, an active sliding mode controller, which employs a dynamic output feedback sliding surface for the unmatched condition and an adaptive law for disturbance estimation, is designed, analyzed, and validated for chatter suppression in turning process. Only displacement measurement is required by this approach. Other sensors and state observers are not needed. Moreover, it facilitates a rapid implementation since the designed controller is established without using model parameters of the turning process. Theoretical analysis, numerical simulations and experiments on a computer numerical control (CNC) lathe are presented. It shows that the chatter can be substantially attenuated and the chatter-free region can be significantly expanded with the presented method.

Team Software Development for Aerothermodynamic and Aerodynamic Analysis and Design

NASA Technical Reports Server (NTRS)

Alexandrov, N.; Atkins, H. L.; Bibb, K. L.; Biedron, R. T.; Carpenter, M. H.; Gnoffo, P. A.; Hammond, D. P.; Jones, W. T.; Kleb, W. L.; Lee-Rausch, E. M.

2003-01-01

A collaborative approach to software development is described. The approach employs the agile development techniques: project retrospectives, Scrum status meetings, and elements of Extreme Programming to efficiently develop a cohesive and extensible software suite. The software product under development is a fluid dynamics simulator for performing aerodynamic and aerothermodynamic analysis and design. The functionality of the software product is achieved both through the merging, with substantial rewrite, of separate legacy codes and the authorship of new routines. Examples of rapid implementation of new functionality demonstrate the benefits obtained with this agile software development process. The appendix contains a discussion of coding issues encountered while porting legacy Fortran 77 code to Fortran 95, software design principles, and a Fortran 95 coding standard.

Chemical vapor infiltration of TiB{sub 2} fibrous composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Besmann, T.M.

1997-04-01

This program is designed to develop a Hall-Heroult aluminum smelting cathode with substantially improved properties. The carbon cathodes in current use require significant anode-to-cathode spacing in order to prevent shorting, causing significant electrical inefficiencies. This is due to the non-wettability of carbon by aluminum which causes instability in the cathodic aluminum pad. It is suggested that a fiber reinforced-TiB{sub 2} matrix composite would have the requisite wettability, strength, strain-to-failure, cost, and lifetime to solve this problem. The approach selected to fabricate such a cathode material is chemical vapor infiltration (CVI). This process produces high purity matrix TiB{sub 2} without damagingmore » the relatively fragile fibers. The program is designed to evaluate potential fiber reinforcements, fabricate test specimens, and scale the process to provide demonstration components.« less

DeMAID: A Design Manager's Aide for Intelligent Decomposition user's guide

NASA Technical Reports Server (NTRS)

Rogers, James L.

1989-01-01

A design problem is viewed as a complex system divisible into modules. Before the design of a complex system can begin, the couplings among modules and the presence of iterative loops is determined. This is important because the design manager must know how to group the modules into subsystems and how to assign subsystems to design teams so that changes in one subsystem will have predictable effects on other subsystems. Determining these subsystems is not an easy, straightforward process and often important couplings are overlooked. Moreover, the planning task must be repeated as new information become available or as the design specifications change. The purpose of this research is to develop a knowledge-based tool called the Design Manager's Aide for Intelligent Decomposition (DeMAID) to act as an intelligent advisor for the design manager. DeMaid identifies the subsystems of a complex design problem, orders them into a well-structured format, and marks the couplings among the subsystems to facilitate the use of multilevel tools. DeMAID also provides the design manager with the capability of examining the trade-offs between sequential and parallel processing. This type of approach could lead to a substantial savings or organizing and displaying a complex problem as a sequence of subsystems easily divisible among design teams. This report serves as a User's Guide for the program.

Composite Cryotank Technologies and Development 2.4 and 5.5M out of Autoclave Tank Test Results

NASA Technical Reports Server (NTRS)

Jackson, Justin R.; Vickers, John; Fikes, John

2015-01-01

The Composite Cryotank Technologies and Demonstration (CCTD) project substantially matured composite, cryogenic propellant tank technology. The project involved the design, analysis, fabrication, and testing of large-scale (2.4-m-diameter precursor and 5.5-m-diameter) composite cryotanks. Design features included a one-piece wall design that minimized tank weight, a Y-joint that incorporated an engineered material to alleviate stress concentration under combined loading, and a fluted core cylindrical section that inherently allows for venting and purging. The tanks used out-of-autoclave (OoA) cured graphite/epoxy material and processes to enable large (up to 10-m-diameter) cryotank fabrication, and thin-ply prepreg to minimize hydrogen permeation through tank walls. Both tanks were fabricated at Boeing using automated fiber placement on breakdown tooling. A fluted core skirt that efficiently carried axial loads and enabled hydrogen purging was included on the 5.5-m-diameter tank. Ultrasonic inspection was performed, and a structural health monitoring system was installed to identify any impact damage during ground processing. The precursor and 5.5-m-diameter tanks were tested in custom test fixtures at the National Aeronautics and Space Administration Marshall Space Flight Center. The testing, which consisted of a sequence of pressure and thermal cycles using liquid hydrogen, was successfully concluded and obtained valuable structural, thermal, and permeation performance data. This technology can be applied to a variety of aircraft and spacecraft applications that would benefit from 30 to 40% weight savings and substantial cost savings compared to aluminum lithium tanks.

Electrostatic separation for recycling waste printed circuit board: a study on external factor and a robust design for optimization.

PubMed

Hou, Shibing; Wu, Jiang; Qin, Yufei; Xu, Zhenming

2010-07-01

Electrostatic separation is an effective and environmentally friendly method for recycling waste printed circuit board (PCB) by several kinds of electrostatic separators. However, some notable problems have been detected in its applications and cannot be efficiently resolved by optimizing the separation process. Instead of the separator itself, these problems are mainly caused by some external factors such as the nonconductive powder (NP) and the superficial moisture of feeding granule mixture. These problems finally lead to an inefficient separation. In the present research, the impacts of these external factors were investigated and a robust design was built to optimize the process and to weaken the adverse impact. A most robust parameter setting (25 kv, 80 rpm) was concluded from the experimental design. In addition, some theoretical methods, including cyclone separation, were presented to eliminate these problems substantially. This will contribute to efficient electrostatic separation of waste PCB and make remarkable progress for industrial applications.

Efficient and lightweight current leads

NASA Astrophysics Data System (ADS)

Bromberg, L.; Dietz, A. J.; Michael, P. C.; Gold, C.; Cheadle, M.

2014-01-01

Current leads generate substantial cryogenic heat loads in short length High Temperature Superconductor (HTS) distribution systems. Thermal conduction, as well as Joule losses (I2R) along the current leads, comprises the largest cryogenic loads for short distribution systems. Current leads with two temperature stages have been designed, constructed and tested, with the goal of minimizing the electrical power consumption, and to provide thermal margin for the cable. We present the design of a two-stage current lead system, operating at 140 K and 55 K. This design is very attractive when implemented with a turbo-Brayton cycle refrigerator (two-stage), with substantial power and weight reduction. A heat exchanger is used at each temperature station, with conduction-cooled stages in-between. Compact, efficient heat exchangers are challenging, because of the gaseous coolant. Design, optimization and performance of the heat exchangers used for the current leads will be presented. We have made extensive use of CFD models for optimizing hydraulic and thermal performance of the heat exchangers. The methodology and the results of the optimization process will be discussed. The use of demountable connections between the cable and the terminations allows for ease of assembly, but require means of aggressively cooling the region of the joint. We will also discuss the cooling of the joint. We have fabricated a 7 m, 5 kA cable with second generation HTS tapes. The performance of the system will be described.

The role of behavioral decision theory for cockpit information management

NASA Technical Reports Server (NTRS)

Jonsson, Jon E.

1991-01-01

The focus of this report is the consideration of one form of cognition, judgment and decision making, while examining some information management issues associated with the implementation of new forms of automation. As technology matures and more tasks become suitable to automation, human factors researchers will have to consider the effect that increasing automation will have on operator performance. Current technology allows flight deck designers the opportunity to automate activities involving substantially more cognitive processing.

Developmental engineering: a new paradigm for the design and manufacturing of cell-based products. Part II: from genes to networks: tissue engineering from the viewpoint of systems biology and network science.

PubMed

Lenas, Petros; Moos, Malcolm; Luyten, Frank P

2009-12-01

The field of tissue engineering is moving toward a new concept of "in vitro biomimetics of in vivo tissue development." In Part I of this series, we proposed a theoretical framework integrating the concepts of developmental biology with those of process design to provide the rules for the design of biomimetic processes. We named this methodology "developmental engineering" to emphasize that it is not the tissue but the process of in vitro tissue development that has to be engineered. To formulate the process design rules in a rigorous way that will allow a computational design, we should refer to mathematical methods to model the biological process taking place in vitro. Tissue functions cannot be attributed to individual molecules but rather to complex interactions between the numerous components of a cell and interactions between cells in a tissue that form a network. For tissue engineering to advance to the level of a technologically driven discipline amenable to well-established principles of process engineering, a scientifically rigorous formulation is needed of the general design rules so that the behavior of networks of genes, proteins, or cells that govern the unfolding of developmental processes could be related to the design parameters. Now that sufficient experimental data exist to construct plausible mathematical models of many biological control circuits, explicit hypotheses can be evaluated using computational approaches to facilitate process design. Recent progress in systems biology has shown that the empirical concepts of developmental biology that we used in Part I to extract the rules of biomimetic process design can be expressed in rigorous mathematical terms. This allows the accurate characterization of manufacturing processes in tissue engineering as well as the properties of the artificial tissues themselves. In addition, network science has recently shown that the behavior of biological networks strongly depends on their topology and has developed the necessary concepts and methods to describe it, allowing therefore a deeper understanding of the behavior of networks during biomimetic processes. These advances thus open the door to a transition for tissue engineering from a substantially empirical endeavor to a technology-based discipline comparable to other branches of engineering.

Doppler Lidar System Design via Interdisciplinary Design Concept at NASA Langley Research Center - Part I

NASA Technical Reports Server (NTRS)

Boyer, Charles M.; Jackson, Trevor P.; Beyon, Jeffrey Y.; Petway, Larry B.

2013-01-01

Optimized designs of the Navigation Doppler Lidar (NDL) instrument for Autonomous Landing Hazard Avoidance Technology (ALHAT) were accomplished via Interdisciplinary Design Concept (IDEC) at NASA Langley Research Center during the summer of 2013. Three branches in the Engineering Directorate and three students were involved in this joint task through the NASA Langley Aerospace Research Summer Scholars (LARSS) Program. The Laser Remote Sensing Branch (LRSB), Mechanical Systems Branch (MSB), and Structural and Thermal Systems Branch (STSB) were engaged to achieve optimal designs through iterative and interactive collaborative design processes. A preliminary design iteration was able to reduce the power consumption, mass, and footprint by removing redundant components and replacing inefficient components with more efficient ones. A second design iteration reduced volume and mass by replacing bulky components with excessive performance with smaller components custom-designed for the power system. Mechanical placement collaboration reduced potential electromagnetic interference (EMI). Through application of newly selected electrical components and thermal analysis data, a total electronic chassis redesign was accomplished. Use of an innovative forced convection tunnel heat sink was employed to meet and exceed project requirements for cooling, mass reduction, and volume reduction. Functionality was a key concern to make efficient use of airflow, and accessibility was also imperative to allow for servicing of chassis internals. The collaborative process provided for accelerated design maturation with substantiated function.

Development of a Web-Based Health Care Intervention for Patients With Heart Disease: Lessons Learned From a Participatory Design Study

PubMed Central

2017-01-01

Background The use of telemedicine technologies in health care has increased substantially, together with a growing interest in participatory design methods when developing telemedicine approaches. Objective We present lessons learned from a case study involving patients with heart disease and health care professionals in the development of a personalized Web-based health care intervention. Methods We used a participatory design approach inspired by the method for feasibility studies in software development. We collected qualitative data using multiple methods in 3 workshops and analyzed the data using thematic analysis. Participants were 7 patients with diagnosis of heart disease, 2 nurses, 1 physician, 2 systems architects, 3 moderators, and 3 observers. Results We present findings in 2 parts. (1) Outcomes of the participatory design process: users gave valuable feedback on ease of use of the platforms’ tracking tools, platform design, terminology, and insights into patients’ monitoring needs, information and communication technologies skills, and preferences for self-management tools. (2) Experiences from the participatory design process: patients and health care professionals contributed different perspectives, with the patients using an experience-based approach and the health care professionals using a more attitude-based approach. Conclusions The essential lessons learned concern planning and organization of workshops, including the finding that patients engaged actively and willingly in a participatory design process, whereas it was more challenging to include and engage health care professionals. PMID:28526674

Long life 80Ah standard IPV NiH2 battery cell

NASA Technical Reports Server (NTRS)

Armantrout, Jon D.; Waller, J. S.

1995-01-01

A standard Nickel-Hydrogen (NiH2) Individual Pressure Vessel (IPV) battery cell is needed to meet future low cost, high performance mission requirements for NASA, military, and civil space programs. A common or standard cell design has evolved from the heritage of HST, Milstar, and other Air Force Mantech cell designs with substantial flight experience, while incorporating some of the historical COMSAT cell design features described in a previous NASA publication. Key features include slurry process nickel electrodes having high strength, long life and high yield (lower cost), and dual layer zircar separators for improved KOH retention, uniformality, and longer life. The cell design will have a zirconium oxide wall wick inside the pressure vessel to redistribute electrolyte and extend life. The slurry electrode will be 35 mils thick to take advantage of qualified cell mechanical configurations and proven assembly and activation techniques developed by Eagle Picher Industries (EPI) for the Hubble Space Telescope (HST) RNH-90-3 and 'Generic HST' RNH-90-5 cell designs with back-to-back nickel electrodes produced by the dry sinter process. The 80Ah common cell design can be scaled to meet capacity requirements from 60Ah to 100Ah. Producibility, commonality, and long life performance will be enhanced with the robust cell design described herein.

Multisite Assessment of Nursing Continuing Education Learning Needs Using an Electronic Tool.

PubMed

Winslow, Susan; Jackson, Stephanie; Cook, Lesley; Reed, Joanne Williams; Blakeney, Keshia; Zimbro, Kathie; Parker, Cindy

2016-02-01

A continued education needs assessment and associated education plan are required for organizations on the journey for American Nurses Credentialing Center Magnet® designation. Leveraging technology to support the assessment and analysis of continuing education needs was a new venture for a 12-hospital regional health system. The purpose of this performance improvement project was to design and conduct an enhanced process to increase the efficiency and effectiveness of gathering data on nurses' preferences and increase nurse satisfaction with the learner assessment portion of the process. Educators trialed the use of a standardized approach via an electronic survey tool to replace the highly variable processes previously used. Educators were able to view graphical summary of responses by category and setting, which substantially decreased analysis and action planning time for education implementation plans at the system, site, or setting level. Based on these findings, specific continuing education action plans were drafted for each category and classification of nurses. Copyright 2016, SLACK Incorporated.

Mistreatment in Assisted Living Facilities: Complaints, Substantiations, and Risk Factors

ERIC Educational Resources Information Center

Phillips, Linda R.; Guo, Guifang

2011-01-01

Purpose of the Study: Use archived public data from Arizona to explore relationships among selected institutional and resident risk and situation-specific factors and complaints and substantiated allegations of various types of mistreatment in assisted living facilities (ALFs). Design and Methods: An exploratory/descriptive 2-group design was…

24 CFR 598.430 - Revocation of designation.

Code of Federal Regulations, 2011 CFR

2011-04-01

... approval from HUD; (2) Has failed to make progress in implementing the strategic plan; or (3) Has not complied substantially with the strategic plan. (b) Letter of warning. Before revoking the designation of... complying substantially with, or has failed to make progress in implementing the strategic plan; and (2...

24 CFR 598.430 - Revocation of designation.

Code of Federal Regulations, 2010 CFR

2010-04-01

... approval from HUD; (2) Has failed to make progress in implementing the strategic plan; or (3) Has not complied substantially with the strategic plan. (b) Letter of warning. Before revoking the designation of... complying substantially with, or has failed to make progress in implementing the strategic plan; and (2...

LSST Telescope and Optics Status

NASA Astrophysics Data System (ADS)

Krabbendam, Victor; Gressler, W. J.; Andrew, J. R.; Barr, J. D.; DeVries, J.; Hileman, E.; Liang, M.; Neill, D. R.; Sebag, J.; Wiecha, O.; LSST Collaboration

2011-01-01

The LSST Project continues to advance the design and development of an observatory system capable of capturing 20,000 deg2 of the sky in six wavebands over ten years. Optical fabrication of the unique M1/M3 monolithic mirror has entered final front surface optical processing. After substantial grinding to remove 5 tons of excess glass above the M3 surface, a residual of a single spin casting, both distinct optical surfaces are now clearly evident. Loose abrasive grinding has begun and polishing is to occur during 2011 and final optical testing is planned in early 2012. The M1/M3 telescope cell and internal component designs have matured to support on telescope operational requirements and off telescope coating needs. The mirror position system (hardpoint actuators) and mirror support system (figure actuator) designs have developed through internal laboratory analysis and testing. Review of thermal requirements has assisted with definition of a thermal conditioning and control system. Pre-cooling the M1/M3 substrate will enable productive observing during the large temperature swing often seen at twilight. The M2 ULE™ substrate is complete and lies in storage waiting for additional funding to enable final optical polishing. This 3.5m diameter, 100mm thick meniscus substrate has been ground to within 40 microns of final figure. Detailed design of the telescope mount, including subflooring, has been developed. Finally, substantial progress has been achieved on the facility design. In early 2010, LSST contracted with ARCADIS Geotecnica Consultores, a Santiago based engineering firm to lead the formal architectural design effort for the summit facility.

Establishing and Maintaining an Extensive Library of Patient-Derived Xenograft Models.

PubMed

Mattar, Marissa; McCarthy, Craig R; Kulick, Amanda R; Qeriqi, Besnik; Guzman, Sean; de Stanchina, Elisa

2018-01-01

Patient-derived xenograft (PDX) models have recently emerged as a highly desirable platform in oncology and are expected to substantially broaden the way in vivo studies are designed and executed and to reshape drug discovery programs. However, acquisition of patient-derived samples, and propagation, annotation and distribution of PDXs are complex processes that require a high degree of coordination among clinic, surgery and laboratory personnel, and are fraught with challenges that are administrative, procedural and technical. Here, we examine in detail the major aspects of this complex process and relate our experience in establishing a PDX Core Laboratory within a large academic institution.

Design and experimental study on desulphurization process of ship exhaust

NASA Astrophysics Data System (ADS)

Han, Mingyang; Hao, Shan; Zhou, Junbo; Gao, Liping

2018-02-01

This desulfurization process involves removing sulfur oxides with seawater or alkaline aqueous solutions and then treating the effluent by aeration and pH adjustment before discharging it into the ocean. In the desulfurization system, the spray tower is the key equipment and the venturi tubes are the pretreatment device. The two stages of plates are designed to fully absorb sulfur oxides in exhaust gases. The spiral nozzles atomize and evenly spray the desulfurizers into the tower. This study experimentally investigated the effectiveness of this desulfurization process and the factors influencing it under laboratory conditions, with a diesel engine exhaust used to represent ship exhaust. The experimental results show that this process can effectively absorb the SO2 in the exhaust. When the exhaust flow rate was 25 m3/h and the desulfurizer flow rate was 4 L/min, the sulfur removal efficiency (SRE) reached 99.7%. The flow rate, alkalinity, and temperature of seawater were found to have significant effects on the SRE. Adjusting seawater flow rate (SWR) and alkalinity within certain ranges can substantially improve the SRE.

VLSI technology for smaller, cheaper, faster return link systems

NASA Technical Reports Server (NTRS)

Nanzetta, Kathy; Ghuman, Parminder; Bennett, Toby; Solomon, Jeff; Dowling, Jason; Welling, John

1994-01-01

Very Large Scale Integration (VLSI) Application-specific Integrated Circuit (ASIC) technology has enabled substantially smaller, cheaper, and more capable telemetry data systems. However, the rapid growth in available ASIC fabrication densities has far outpaced the application of this technology to telemetry systems. Available densities have grown by well over an order magnitude since NASA's Goddard Space Flight Center (GSFC) first began developing ASIC's for ground telemetry systems in 1985. To take advantage of these higher integration levels, a new generation of ASIC's for return link telemetry processing is under development. These new submicron devices are designed to further reduce the cost and size of NASA return link processing systems while improving performance. This paper describes these highly integrated processing components.

Control of Future Air Traffic Systems via Complexity Bound Management

NASA Technical Reports Server (NTRS)

Alexandrov, Natalia

2013-01-01

The complexity of the present system for managing air traffic has led to "discreteness" in approaches to creating new concepts: new concepts are created as point designs, based on experience, expertise, and creativity of the proposer. Discrete point designs may be highly successful but they are difficult to substantiate in the face of equally strong substantiation of competing concepts, as well as the state of the art in concept evaluation via simulations. Hybrid concepts may present a compromise - the golden middle. Yet a hybrid of sometimes in principle incompatible concepts forms another point design that faces the challenge of substantiation and validation. We are faced with the need to re-design the air transportation system ab initio. This is a daunting task, especially considering the problem of transitioning from the present system to any fundamentally new system. However, design from scratch is also an opportunity to reconsider approaches to new concept development. In this position paper we propose an approach, Optimized Parametric Functional Design, for systematic development of concepts for management and control of airspace systems, based on optimization formulations in terms of required system functions and states. This reasoning framework, realizable in the context of ab initio system design, offers an approach to deriving substantiated airspace management and control concepts. With growing computational power, we hope that the approach will also yield a methodology for actual dynamic control of airspace

Kilogram-scale prexasertib monolactate monohydrate synthesis under continuous-flow CGMP conditions.

PubMed

Cole, Kevin P; Groh, Jennifer McClary; Johnson, Martin D; Burcham, Christopher L; Campbell, Bradley M; Diseroad, William D; Heller, Michael R; Howell, John R; Kallman, Neil J; Koenig, Thomas M; May, Scott A; Miller, Richard D; Mitchell, David; Myers, David P; Myers, Steven S; Phillips, Joseph L; Polster, Christopher S; White, Timothy D; Cashman, Jim; Hurley, Declan; Moylan, Robert; Sheehan, Paul; Spencer, Richard D; Desmond, Kenneth; Desmond, Paul; Gowran, Olivia

2017-06-16

Advances in drug potency and tailored therapeutics are promoting pharmaceutical manufacturing to transition from a traditional batch paradigm to more flexible continuous processing. Here we report the development of a multistep continuous-flow CGMP (current good manufacturing practices) process that produced 24 kilograms of prexasertib monolactate monohydrate suitable for use in human clinical trials. Eight continuous unit operations were conducted to produce the target at roughly 3 kilograms per day using small continuous reactors, extractors, evaporators, crystallizers, and filters in laboratory fume hoods. Success was enabled by advances in chemistry, engineering, analytical science, process modeling, and equipment design. Substantial technical and business drivers were identified, which merited the continuous process. The continuous process afforded improved performance and safety relative to batch processes and also improved containment of a highly potent compound. Copyright © 2017, American Association for the Advancement of Science.

Process yield improvements with process control terminal for varian serial ion implanters

NASA Astrophysics Data System (ADS)

Higashi, Harry; Soni, Ameeta; Martinez, Larry; Week, Ken

Implant processes in a modern wafer production fab are extremely complex. There can be several types of misprocessing, i.e. wrong dose or species, double implants and missed implants. Process Control Terminals (PCT) for Varian 350Ds installed at Intel fabs were found to substantially reduce the number of misprocessing steps. This paper describes those misprocessing steps and their subsequent reduction with use of PCTs. Reliable and simple process control with serial process ion implanters has been in increasing demand. A well designed process control terminal greatly increases device yield by monitoring all pertinent implanter functions and enabling process engineering personnel to set up process recipes for simple and accurate system operation. By programming user-selectable interlocks, implant errors are reduced and those that occur are logged for further analysis and prevention. A process control terminal should also be compatible with office personal computers for greater flexibility in system use and data analysis. The impact from the capability of a process control terminal is increased productivity, ergo higher device yield.

Bayesian adaptive phase II screening design for combination trials.

PubMed

Cai, Chunyan; Yuan, Ying; Johnson, Valen E

2013-01-01

Trials of combination therapies for the treatment of cancer are playing an increasingly important role in the battle against this disease. To more efficiently handle the large number of combination therapies that must be tested, we propose a novel Bayesian phase II adaptive screening design to simultaneously select among possible treatment combinations involving multiple agents. Our design is based on formulating the selection procedure as a Bayesian hypothesis testing problem in which the superiority of each treatment combination is equated to a single hypothesis. During the trial conduct, we use the current values of the posterior probabilities of all hypotheses to adaptively allocate patients to treatment combinations. Simulation studies show that the proposed design substantially outperforms the conventional multiarm balanced factorial trial design. The proposed design yields a significantly higher probability for selecting the best treatment while allocating substantially more patients to efficacious treatments. The proposed design is most appropriate for the trials combining multiple agents and screening out the efficacious combination to be further investigated. The proposed Bayesian adaptive phase II screening design substantially outperformed the conventional complete factorial design. Our design allocates more patients to better treatments while providing higher power to identify the best treatment at the end of the trial.

The rare earth element (REE) lanthanum (La) induces hormesis in plants.

PubMed

Agathokleous, Evgenios; Kitao, Mitsutoshi; Calabrese, Edward J

2018-07-01

Lanthanum is a rare earth element (REE) which has been extensively studied due to its wide application in numerous fields with a potential accumulation in the environment. It has long been known for its potential to stimulate plant growth within a hormetic-biphasic dose response framework. This article provides evidence from a series of high resolution studies published within the last two decades demonstrating a substantial and significant occurrence of lanthanum-induced hormesis in plants. These findings suggest that hormetic responses should be built into the study design of hazard assessment study protocols and included in the risk assessment process. Hormesis also offers the opportunity to substantially improve cost benefit estimates for environmental contaminants, which have the potential to induce beneficial/desirable effects at low doses. Copyright © 2018 Elsevier Ltd. All rights reserved.

Automated installation methods for photovoltaic arrays

NASA Astrophysics Data System (ADS)

Briggs, R.; Daniels, A.; Greenaway, R.; Oster, J., Jr.; Racki, D.; Stoeltzing, R.

1982-11-01

Since installation expenses constitute a substantial portion of the cost of a large photovoltaic power system, methods for reduction of these costs were investigated. The installation of the photovoltaic arrays includes all areas, starting with site preparation (i.e., trenching, wiring, drainage, foundation installation, lightning protection, grounding and installation of the panel) and concluding with the termination of the bus at the power conditioner building. To identify the optimum combination of standard installation procedures and automated/mechanized techniques, the installation process was investigated including the equipment and hardware available, the photovoltaic array structure systems and interfaces, and the array field and site characteristics. Preliminary designs of hardware for both the standard installation method, the automated/mechanized method, and a mix of standard installation procedures and mechanized procedures were identified to determine which process effectively reduced installation costs. In addition, costs associated with each type of installation method and with the design, development and fabrication of new installation hardware were generated.

The Flight Optimization System Weights Estimation Method

NASA Technical Reports Server (NTRS)

Wells, Douglas P.; Horvath, Bryce L.; McCullers, Linwood A.

2017-01-01

FLOPS has been the primary aircraft synthesis software used by the Aeronautics Systems Analysis Branch at NASA Langley Research Center. It was created for rapid conceptual aircraft design and advanced technology impact assessments. FLOPS is a single computer program that includes weights estimation, aerodynamics estimation, engine cycle analysis, propulsion data scaling and interpolation, detailed mission performance analysis, takeoff and landing performance analysis, noise footprint estimation, and cost analysis. It is well known as a baseline and common denominator for aircraft design studies. FLOPS is capable of calibrating a model to known aircraft data, making it useful for new aircraft and modifications to existing aircraft. The weight estimation method in FLOPS is known to be of high fidelity for conventional tube with wing aircraft and a substantial amount of effort went into its development. This report serves as a comprehensive documentation of the FLOPS weight estimation method. The development process is presented with the weight estimation process.

Low-cost manufacturing of the point focus concentrating module and its key component, the Fresnel lens. Final subcontract report, 31 January 1991--6 May 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saifee, T.; Konnerth, A. III

1991-11-01

Solar Kinetics, Inc. (SKI) has been developing point-focus concentrating PV modules since 1986. SKI is currently in position to manufacture between 200 to 600 kilowatts annually of the current design by a combination of manual and semi-automated methods. This report reviews the current status of module manufacture and specifies the required approach to achieve a high-volume manufacturing capability and low cost. The approach taken will include process development concurrent with module design for automated manufacturing. The current effort reviews the major manufacturing costs and identifies components and processes whose improvements would produce the greatest effect on manufacturability and cost reduction.more » The Fresnel lens is one such key component. Investigating specific alternative manufacturing methods and sources has substantially reduced the lens costs and has exceeded the DOE cost-reduction goals. 15 refs.« less

A Model for Oil-Gas Pipelines Cost Prediction Based on a Data Mining Process

NASA Astrophysics Data System (ADS)

Batzias, Fragiskos A.; Spanidis, Phillip-Mark P.

2009-08-01

This paper addresses the problems associated with the cost estimation of oil/gas pipelines during the elaboration of feasibility assessments. Techno-economic parameters, i.e., cost, length and diameter, are critical for such studies at the preliminary design stage. A methodology for the development of a cost prediction model based on Data Mining (DM) process is proposed. The design and implementation of a Knowledge Base (KB), maintaining data collected from various disciplines of the pipeline industry, are presented. The formulation of a cost prediction equation is demonstrated by applying multiple regression analysis using data sets extracted from the KB. Following the methodology proposed, a learning context is inductively developed as background pipeline data are acquired, grouped and stored in the KB, and through a linear regression model provide statistically substantial results, useful for project managers or decision makers.

Multicomponent Arcjet plasma Parameters

NASA Astrophysics Data System (ADS)

Gorbunkov, V.; Kositsin, V. V.; Ruban, V. I.; Shalay, V. V.

2018-01-01

To determine the plasma arc parameters of an arcjet thruster, the kinetic theory of gases is used. We can find a well-known statement about the adiabatic character of the compression process due to the growth of the gas temperature in a change in its spectral composition and in the Doppler effect. The use of tungsten in the nozzle design details explains the appearance of atoms of this element in the plasma volume. The emission spectra of tungsten allow us to indirectly judge the temperature of the arc discharge and its character. Absorption of the long-wavelength wing of the line contour at λ = 465.987 nm substantiates our conclusion about the consumption of the anode material in the process of operating the arcjet. The Doppler shift of the emission lines of argon allows us to determine the rate of the gas jet escape. The results of the study can be useful in the design of aircraft.

A social science data-fusion tool and the Data Management through e-Social Science (DAMES) infrastructure.

PubMed

Warner, Guy C; Blum, Jesse M; Jones, Simon B; Lambert, Paul S; Turner, Kenneth J; Tan, Larry; Dawson, Alison S F; Bell, David N F

2010-08-28

The last two decades have seen substantially increased potential for quantitative social science research. This has been made possible by the significant expansion of publicly available social science datasets, the development of new analytical methodologies, such as microsimulation, and increases in computing power. These rich resources do, however, bring with them substantial challenges associated with organizing and using data. These processes are often referred to as 'data management'. The Data Management through e-Social Science (DAMES) project is working to support activities of data management for social science research. This paper describes the DAMES infrastructure, focusing on the data-fusion process that is central to the project approach. It covers: the background and requirements for provision of resources by DAMES; the use of grid technologies to provide easy-to-use tools and user front-ends for several common social science data-management tasks such as data fusion; the approach taken to solve problems related to data resources and metadata relevant to social science applications; and the implementation of the architecture that has been designed to achieve this infrastructure.

Automated knowledge base development from CAD/CAE databases

NASA Technical Reports Server (NTRS)

Wright, R. Glenn; Blanchard, Mary

1988-01-01

Knowledge base development requires a substantial investment in time, money, and resources in order to capture the knowledge and information necessary for anything other than trivial applications. This paper addresses a means to integrate the design and knowledge base development process through automated knowledge base development from CAD/CAE databases and files. Benefits of this approach include the development of a more efficient means of knowledge engineering, resulting in the timely creation of large knowledge based systems that are inherently free of error.

Multi-Core Programming Design Patterns: Stream Processing Algorithms for Dynamic Scene Perceptions

DTIC Science & Technology

2014-05-01

processor developed by IBM and other companies , incorpo- rates the verb—POWER5— processor as the Power Processor Element (PPE), one of the early general...deliver an power efficient single-precision peak performance of more than 256 GFlops. Substantially more raw power became available later, when nVIDIA ...algorithms, including IBM’s Cell/B.E., GPUs from NVidia and AMD and many-core CPUs from Intel.27 The vast growth of digital video content has been a

Off-design analysis of a gas turbine powerplant augmented by steam injection using various fuels

NASA Technical Reports Server (NTRS)

Stochl, R. J.

1980-01-01

Results are compared using coal derived low and intermediate heating valve fuel gases and a conventional distillate. The results indicate that steam injection provides substantial increases in both power and efficiency within the available compressor surge margin. The results also indicate that these performance gains are relatively insensitive as to the type of fuel. Also, in a cogeneration application, steam injection could provide some degree of flexibility by varying the split between power and process steam.

Precision of Sensitivity in the Design Optimization of Indeterminate Structures

NASA Technical Reports Server (NTRS)

Patnaik, Surya N.; Pai, Shantaram S.; Hopkins, Dale A.

2006-01-01

Design sensitivity is central to most optimization methods. The analytical sensitivity expression for an indeterminate structural design optimization problem can be factored into a simple determinate term and a complicated indeterminate component. Sensitivity can be approximated by retaining only the determinate term and setting the indeterminate factor to zero. The optimum solution is reached with the approximate sensitivity. The central processing unit (CPU) time to solution is substantially reduced. The benefit that accrues from using the approximate sensitivity is quantified by solving a set of problems in a controlled environment. Each problem is solved twice: first using the closed-form sensitivity expression, then using the approximation. The problem solutions use the CometBoards testbed as the optimization tool with the integrated force method as the analyzer. The modification that may be required, to use the stiffener method as the analysis tool in optimization, is discussed. The design optimization problem of an indeterminate structure contains many dependent constraints because of the implicit relationship between stresses, as well as the relationship between the stresses and displacements. The design optimization process can become problematic because the implicit relationship reduces the rank of the sensitivity matrix. The proposed approximation restores the full rank and enhances the robustness of the design optimization method.

Business Process Modeling: Perceived Benefits

NASA Astrophysics Data System (ADS)

Indulska, Marta; Green, Peter; Recker, Jan; Rosemann, Michael

The process-centered design of organizations and information systems is globally seen as an appropriate response to the increased economic pressure on organizations. At the methodological core of process-centered management is process modeling. However, business process modeling in large initiatives can be a time-consuming and costly exercise, making it potentially difficult to convince executive management of its benefits. To date, and despite substantial interest and research in the area of process modeling, the understanding of the actual benefits of process modeling in academia and practice is limited. To address this gap, this paper explores the perception of benefits derived from process modeling initiatives, as reported through a global Delphi study. The study incorporates the views of three groups of stakeholders - academics, practitioners and vendors. Our findings lead to the first identification and ranking of 19 unique benefits associated with process modeling. The study in particular found that process modeling benefits vary significantly between practitioners and academics. We argue that the variations may point to a disconnect between research projects and practical demands.

NULL Convention Floating Point Multiplier

PubMed Central

Ramachandran, Seshasayanan

2015-01-01

Floating point multiplication is a critical part in high dynamic range and computational intensive digital signal processing applications which require high precision and low power. This paper presents the design of an IEEE 754 single precision floating point multiplier using asynchronous NULL convention logic paradigm. Rounding has not been implemented to suit high precision applications. The novelty of the research is that it is the first ever NULL convention logic multiplier, designed to perform floating point multiplication. The proposed multiplier offers substantial decrease in power consumption when compared with its synchronous version. Performance attributes of the NULL convention logic floating point multiplier, obtained from Xilinx simulation and Cadence, are compared with its equivalent synchronous implementation. PMID:25879069

NULL convention floating point multiplier.

PubMed

Albert, Anitha Juliette; Ramachandran, Seshasayanan

2015-01-01

Floating point multiplication is a critical part in high dynamic range and computational intensive digital signal processing applications which require high precision and low power. This paper presents the design of an IEEE 754 single precision floating point multiplier using asynchronous NULL convention logic paradigm. Rounding has not been implemented to suit high precision applications. The novelty of the research is that it is the first ever NULL convention logic multiplier, designed to perform floating point multiplication. The proposed multiplier offers substantial decrease in power consumption when compared with its synchronous version. Performance attributes of the NULL convention logic floating point multiplier, obtained from Xilinx simulation and Cadence, are compared with its equivalent synchronous implementation.

Human-Automation Integration: Principle and Method for Design and Evaluation

NASA Technical Reports Server (NTRS)

Billman, Dorrit; Feary, Michael

2012-01-01

Future space missions will increasingly depend on integration of complex engineered systems with their human operators. It is important to ensure that the systems that are designed and developed do a good job of supporting the needs of the work domain. Our research investigates methods for needs analysis. We included analysis of work products (plans for regulation of the space station) as well as work processes (tasks using current software), in a case study of Attitude Determination and Control Officers (ADCO) planning work. This allows comparing how well different designs match the structure of the work to be supported. Redesigned planning software that better matches the structure of work was developed and experimentally assessed. The new prototype enabled substantially faster and more accurate performance in plan revision tasks. This success suggests the approach to needs assessment and use in design and evaluation is promising, and merits investigatation in future research.

Principles of nanoparticle design for overcoming biological barriers to drug delivery

PubMed Central

Blanco, Elvin; Shen, Haifa; Ferrari, Mauro

2016-01-01

Biological barriers to drug transport prevent successful accumulation of nanotherapeutics specifically at diseased sites, limiting efficacious responses in disease processes ranging from cancer to inflammation. Although substantial research efforts have aimed to incorporate multiple functionalities and moieties within the overall nanoparticle design, many of these strategies fail to adequately address these barriers. Obstacles, such as nonspecific distribution and inadequate accumulation of therapeutics, remain formidable challenges to drug developers. A reimagining of conventional nanoparticles is needed to successfully negotiate these impediments to drug delivery. Site-specific delivery of therapeutics will remain a distant reality unless nanocarrier design takes into account the majority, if not all, of the biological barriers that a particle encounters upon intravenous administration. By successively addressing each of these barriers, innovative design features can be rationally incorporated that will create a new generation of nanotherapeutics, realizing a paradigmatic shift in nanoparticle-based drug delivery. PMID:26348965

Naphthalene Diimide Based n-Type Conjugated Polymers as Efficient Cathode Interfacial Materials for Polymer and Perovskite Solar Cells.

PubMed

Jia, Tao; Sun, Chen; Xu, Rongguo; Chen, Zhiming; Yin, Qingwu; Jin, Yaocheng; Yip, Hin-Lap; Huang, Fei; Cao, Yong

2017-10-18

A series of naphthalene diimide (NDI) based n-type conjugated polymers with amino-functionalized side groups and backbones were synthesized and used as cathode interlayers (CILs) in polymer and perovskite solar cells. Because of controllable amine side groups, all the resulting polymers exhibited distinct electronic properties such as oxidation potential of side chains, charge carrier mobilities, self-doping behaviors, and interfacial dipoles. The influences of the chemical variation of amine groups on the cathode interfacial effects were further investigated in both polymer and perovskite solar cells. We found that the decreased electron-donating property and enhanced steric hindrance of amine side groups substantially weaken the capacities of altering the work function of the cathode and trap passivation of the perovskite film, which induced ineffective interfacial modifications and declining device performance. Moreover, with further improvement of the backbone design through the incorporation of a rigid acetylene spacer, the resulting polymers substantially exhibited an enhanced electron-transporting property. Upon use as CILs, high power conversion efficiencies (PCEs) of 10.1% and 15.2% were, respectively, achieved in polymer and perovskite solar cells. Importantly, these newly developed n-type polymers were allowed to be processed over a broad thickness range of CILs in photovoltaic devices, and a prominent PCE of over 8% for polymer solar cells and 13.5% for perovskite solar cells can be achieved with the thick interlayers over 100 nm, which is beneficial for roll-to-roll coating processes. Our findings contribute toward a better understanding of the structure-performance relationship between CIL material design and solar cell performance, and provide important insights and guidelines for the design of high-performance n-type CIL materials for organic and perovskite optoelectronic devices.

Photobioreactor cultivation strategies for microalgae and cyanobacteria.

PubMed

Johnson, Tylor J; Katuwal, Sarmila; Anderson, Gary A; Gu, Liping; Zhou, Ruanbao; Gibbons, William R

2018-03-08

The current burden on fossil-derived chemicals and fuels combined with the rapidly increasing global population has led to a crucial need to develop renewable and sustainable sources of chemicals and biofuels. Photoautotrophic microorganisms, including cyanobacteria and microalgae, have garnered a great deal of attention for their capability to produce these chemicals from carbon dioxide, mineralized water, and solar energy. While there have been substantial amounts of research directed at scaling-up production from these microorganisms, several factors have proven difficult to overcome, including high costs associated with cultivation, photobioreactor construction, and artificial lighting. Decreasing these costs will substantially increase the economic feasibility of these production processes. Thus, the purpose of this review is to describe various photobioreactor designs, and then provide an overview on lighting systems, mixing, gas transfer, and the hydrodynamics of bubbles. These factors must be considered when the goal of a production process is economic feasibility. Targets for improving microalgae and cyanobacteria cultivation media, including water reduction strategies will also be described. As fossil fuel reserves continue to be depleted and the world population continues to increase, it is imperative that renewable chemical and biofuel production processes be developed toward becoming economically feasible. Thus, it is essential that future research is directed toward improving these processes. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 2018. © 2018 American Institute of Chemical Engineers.

Thermomechanical simulations and experimental validation for high speed incremental forming

NASA Astrophysics Data System (ADS)

Ambrogio, Giuseppina; Gagliardi, Francesco; Filice, Luigino; Romero, Natalia

2016-10-01

Incremental sheet forming (ISF) consists in deforming only a small region of the workspace through a punch driven by a NC machine. The drawback of this process is its slowness. In this study, a high speed variant has been investigated from both numerical and experimental points of view. The aim has been the design of a FEM model able to perform the material behavior during the high speed process by defining a thermomechanical model. An experimental campaign has been performed by a CNC lathe with high speed to test process feasibility. The first results have shown how the material presents the same performance than in conventional speed ISF and, in some cases, better material behavior due to the temperature increment. An accurate numerical simulation has been performed to investigate the material behavior during the high speed process confirming substantially experimental evidence.

32 CFR 48.302 - Substantiating evidence regarding dependency and age of dependents.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 1 2012-07-01 2012-07-01 false Substantiating evidence regarding dependency and age of dependents. 48.302 Section 48.302 National Defense Department of Defense OFFICE OF THE... Designation of Beneficiaries § 48.302 Substantiating evidence regarding dependency and age of dependents. At...

32 CFR 48.302 - Substantiating evidence regarding dependency and age of dependents.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 1 2011-07-01 2011-07-01 false Substantiating evidence regarding dependency and age of dependents. 48.302 Section 48.302 National Defense Department of Defense OFFICE OF THE... Designation of Beneficiaries § 48.302 Substantiating evidence regarding dependency and age of dependents. At...

32 CFR 48.302 - Substantiating evidence regarding dependency and age of dependents.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 1 2014-07-01 2014-07-01 false Substantiating evidence regarding dependency and age of dependents. 48.302 Section 48.302 National Defense Department of Defense OFFICE OF THE... Designation of Beneficiaries § 48.302 Substantiating evidence regarding dependency and age of dependents. At...

32 CFR 48.302 - Substantiating evidence regarding dependency and age of dependents.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 1 2013-07-01 2013-07-01 false Substantiating evidence regarding dependency and age of dependents. 48.302 Section 48.302 National Defense Department of Defense OFFICE OF THE... Designation of Beneficiaries § 48.302 Substantiating evidence regarding dependency and age of dependents. At...

32 CFR 48.302 - Substantiating evidence regarding dependency and age of dependents.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 1 2010-07-01 2010-07-01 false Substantiating evidence regarding dependency and age of dependents. 48.302 Section 48.302 National Defense Department of Defense OFFICE OF THE... Designation of Beneficiaries § 48.302 Substantiating evidence regarding dependency and age of dependents. At...

5 CFR 1631.15 - Information to be disclosed.

Code of Federal Regulations, 2010 CFR

2010-01-01

... substantial competitive harm. The submitter as part of its submission, must explain the rationale for the... substantial competitive harm. (iii) After January 1, 1988, a submitter who does not designate portions of a... substantial harm to the competitive position of the submitter. (3) When the Board determines that it has...

5 CFR 1631.15 - Information to be disclosed.

Code of Federal Regulations, 2012 CFR

2012-01-01

... substantial competitive harm. The submitter as part of its submission, must explain the rationale for the... substantial competitive harm. (iii) After January 1, 1988, a submitter who does not designate portions of a... substantial harm to the competitive position of the submitter. (3) When the Board determines that it has...

5 CFR 1631.15 - Information to be disclosed.

Code of Federal Regulations, 2013 CFR

2013-01-01

... substantial competitive harm. The submitter as part of its submission, must explain the rationale for the... substantial competitive harm. (iii) After January 1, 1988, a submitter who does not designate portions of a... substantial harm to the competitive position of the submitter. (3) When the Board determines that it has...

5 CFR 1631.15 - Information to be disclosed.

Code of Federal Regulations, 2011 CFR

2011-01-01

... substantial competitive harm. The submitter as part of its submission, must explain the rationale for the... substantial competitive harm. (iii) After January 1, 1988, a submitter who does not designate portions of a... substantial harm to the competitive position of the submitter. (3) When the Board determines that it has...

5 CFR 1631.15 - Information to be disclosed.

Code of Federal Regulations, 2014 CFR

2014-01-01

... substantial competitive harm. The submitter as part of its submission, must explain the rationale for the... substantial competitive harm. (iii) After January 1, 1988, a submitter who does not designate portions of a... substantial harm to the competitive position of the submitter. (3) When the Board determines that it has...

How does the size and shape of local populations in China compare to general anthropometric surveys currently used for product design?

PubMed

Daniell, Nathan; Fraysse, François; Paul, Gunther

2012-01-01

Anthropometry has long been used for a range of ergonomic applications & product design. Although products are often designed for specific cohorts, anthropometric data are typically sourced from large scale surveys representative of the general population. Additionally, few data are available for emerging markets like China and India. This study measured 80 Chinese males that were representative of a specific cohort targeted for the design of a new product. Thirteen anthropometric measurements were recorded and compared to two large databases that represented a general population, a Chinese database and a Western database. Substantial differences were identified between the Chinese males measured in this study and both databases. The subjects were substantially taller, heavier and broader than subjects in the older Chinese database. However, they were still substantially smaller, lighter and thinner than Western males. Data from current Western anthropometric surveys are unlikely to accurately represent the target population for product designers and manufacturers in emerging markets like China.

Removal of natural organic matter in drinking water treatment by coagulation: A comprehensive review.

PubMed

Sillanpää, Mika; Ncibi, Mohamed Chaker; Matilainen, Anu; Vepsäläinen, Mikko

2018-01-01

Natural organic matter (NOM) is a complex matrix of organic substances produced in (or channeled to) aquatic ecosystems via various biological, geological and hydrological cycles. Such variability is posing a serious challenge to most water treatment technologies, especially the ones designed to treat drinking water supplies. Lately, in addition to the fluctuating composition of NOM, a substantial increase of its concentration in fresh waters, and also municipal wastewater effluents, has been reported worldwide, which justifies the urgent need to develop highly efficient and versatile water treatment processes. Coagulation is among the most applied processes for water and wastewater treatment. The application of coagulation to remove NOM from drinking water supplies has received a great deal of attention from researchers around the world because it was efficient and helped avoiding the formation of disinfection by products (DBPs). Nonetheless, with the increased fluctuation of NOM in water (concentration and composition), the efficiency of conventional coagulation was substantially reduced, hence the need to develop enhanced coagulation processes by optimizing the operating conditions (mainly the amount coagulants and pH), developing more efficient inorganic or organic coagulants, as well as coupling coagulation with other water treatment technologies. In the present review, recent research studies dealing with the application of coagulation for NOM removal from drinking water supplies are presented and compared. In addition, integration schemes combining coagulation and other water treatment processes are presented, including membrane filtration, oxidation, adsorption and others processes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bayesian adaptive phase II screening design for combination trials

PubMed Central

Cai, Chunyan; Yuan, Ying; Johnson, Valen E

2013-01-01

Background Trials of combination therapies for the treatment of cancer are playing an increasingly important role in the battle against this disease. To more efficiently handle the large number of combination therapies that must be tested, we propose a novel Bayesian phase II adaptive screening design to simultaneously select among possible treatment combinations involving multiple agents. Methods Our design is based on formulating the selection procedure as a Bayesian hypothesis testing problem in which the superiority of each treatment combination is equated to a single hypothesis. During the trial conduct, we use the current values of the posterior probabilities of all hypotheses to adaptively allocate patients to treatment combinations. Results Simulation studies show that the proposed design substantially outperforms the conventional multiarm balanced factorial trial design. The proposed design yields a significantly higher probability for selecting the best treatment while allocating substantially more patients to efficacious treatments. Limitations The proposed design is most appropriate for the trials combining multiple agents and screening out the efficacious combination to be further investigated. Conclusions The proposed Bayesian adaptive phase II screening design substantially outperformed the conventional complete factorial design. Our design allocates more patients to better treatments while providing higher power to identify the best treatment at the end of the trial. PMID:23359875

Application of a simple cerebellar model to geologic surface mapping

USGS Publications Warehouse

Hagens, A.; Doveton, J.H.

1991-01-01

Neurophysiological research into the structure and function of the cerebellum has inspired computational models that simulate information processing associated with coordination and motor movement. The cerebellar model arithmetic computer (CMAC) has a design structure which makes it readily applicable as an automated mapping device that "senses" a surface, based on a sample of discrete observations of surface elevation. The model operates as an iterative learning process, where cell weights are continuously modified by feedback to improve surface representation. The storage requirements are substantially less than those of a conventional memory allocation, and the model is extended easily to mapping in multidimensional space, where the memory savings are even greater. ?? 1991.

Systems-on-chip approach for real-time simulation of wheel-rail contact laws

NASA Astrophysics Data System (ADS)

Mei, T. X.; Zhou, Y. J.

2013-04-01

This paper presents the development of a systems-on-chip approach to speed up the simulation of wheel-rail contact laws, which can be used to reduce the requirement for high-performance computers and enable simulation in real time for the use of hardware-in-loop for experimental studies of the latest vehicle dynamic and control technologies. The wheel-rail contact laws are implemented using a field programmable gate array (FPGA) device with a design that substantially outperforms modern general-purpose PC platforms or fixed architecture digital signal processor devices in terms of processing time, configuration flexibility and cost. In order to utilise the FPGA's parallel-processing capability, the operations in the contact laws algorithms are arranged in a parallel manner and multi-contact patches are tackled simultaneously in the design. The interface between the FPGA device and the host PC is achieved by using a high-throughput and low-latency Ethernet link. The development is based on FASTSIM algorithms, although the design can be adapted and expanded for even more computationally demanding tasks.

Payload transportation system study

NASA Technical Reports Server (NTRS)

1976-01-01

A standard size set of shuttle payload transportation equipment was defined that will substantially reduce the cost of payload transportation and accommodate a wide range of payloads with minimum impact on payload design. The system was designed to accommodate payload shipments between the level 4 payload integration sites and the launch site during the calendar years 1979-1982. In addition to defining transportation multi-use mission support equipment (T-MMSE) the mode of travel, prime movers, and ancillary equipment required in the transportation process were also considered. Consistent with the STS goals of low cost and the use of standardized interfaces, the transportation system was designed to commercial grade standards and uses the payload flight mounting interfaces for transportation. The technical, cost, and programmatic data required to permit selection of a baseline system of MMSE for intersite movement of shuttle payloads were developed.

Glyphosate-tolerant soybeans remain compositionally equivalent to conventional soybeans (Glycine max L.) during three years of field testing.

PubMed

McCann, Melinda C; Liu, Keshun; Trujillo, William A; Dobert, Raymond C

2005-06-29

Previous studies have shown that the composition of glyphosate-tolerant soybeans (GTS) and selected processed fractions was substantially equivalent to that of conventional soybeans over a wide range of analytes. This study was designed to determine if the composition of GTS remains substantially equivalent to conventional soybeans over the course of several years and when introduced into multiple genetic backgrounds. Soybean seed samples of both GTS and conventional varieties were harvested during 2000, 2001, and 2002 and analyzed for the levels of proximates, lectin, trypsin inhibitor, and isoflavones. The measured analytes are representative of the basic nutritional and biologically active components in soybeans. Results show a similar range of natural variability for the GTS soybeans as well as conventional soybeans. It was concluded that the composition of commercial GTS over the three years of breeding into multiple varieties remains equivalent to that of conventional soybeans.

Control of phosphorothioate stereochemistry substantially increases the efficacy of antisense oligonucleotides.

PubMed

Iwamoto, Naoki; Butler, David C D; Svrzikapa, Nenad; Mohapatra, Susovan; Zlatev, Ivan; Sah, Dinah W Y; Meena; Standley, Stephany M; Lu, Genliang; Apponi, Luciano H; Frank-Kamenetsky, Maria; Zhang, Jason Jingxin; Vargeese, Chandra; Verdine, Gregory L

2017-09-01

Whereas stereochemical purity in drugs has become the standard for small molecules, stereoisomeric mixtures containing as many as a half million components persist in antisense oligonucleotide (ASO) therapeutics because it has been feasible neither to separate the individual stereoisomers, nor to synthesize stereochemically pure ASOs. Here we report the development of a scalable synthetic process that yields therapeutic ASOs having high stereochemical and chemical purity. Using this method, we synthesized rationally designed stereopure components of mipomersen, a drug comprising 524,288 stereoisomers. We demonstrate that phosphorothioate (PS) stereochemistry substantially affects the pharmacologic properties of ASOs. We report that Sp-configured PS linkages are stabilized relative to Rp, providing stereochemical protection from pharmacologic inactivation of the drug. Further, we elucidated a triplet stereochemical code in the stereopure ASOs, 3'-SpSpRp, that promotes target RNA cleavage by RNase H1 in vitro and provides a more durable response in mice than stereorandom ASOs.

TaN resistor process development and integration.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Romero, Kathleen; Martinez, Marino John; Clevenger, Jascinda

This paper describes the development and implementation of an integrated resistor process based on reactively sputtered tantalum nitride. Image reversal lithography was shown to be a superior method for liftoff patterning of these films. The results of a response surface DOE for the sputter deposition of the films are discussed. Several approaches to stabilization baking were examined and the advantages of the hot plate method are shown. In support of a new capability to produce special-purpose HBT-based Small-Scale Integrated Circuits (SSICs), we developed our existing TaN resistor process, designed for research prototyping, into one with greater maturity and robustness. Includedmore » in this work was the migration of our TaN deposition process from a research-oriented tool to a tool more suitable for production. Also included was implementation and optimization of a liftoff process for the sputtered TaN to avoid the complicating effects of subtractive etching over potentially sensitive surfaces. Finally, the method and conditions for stabilization baking of the resistors was experimentally determined to complete the full implementation of the resistor module. Much of the work to be described involves the migration between sputter deposition tools - from a Kurt J. Lesker CMS-18 to a Denton Discovery 550. Though they use nominally the same deposition technique (reactive sputtering of Ta with N{sup +} in a RF-excited Ar plasma), they differ substantially in their design and produce clearly different results in terms of resistivity, conformity of the film and the difference between as-deposited and stabilized films. We will describe the design of and results from the design of experiments (DOE)-based method of process optimization on the new tool and compare this to what had been used on the old tool.« less

Holistic integration of gaze cues in visual face and body perception: Evidence from the composite design.

PubMed

Vrancken, Leia; Germeys, Filip; Verfaillie, Karl

2017-01-01

A considerable amount of research on identity recognition and emotion identification with the composite design points to the holistic processing of these aspects in faces and bodies. In this paradigm, the interference from a nonattended face half on the perception of the attended half is taken as evidence for holistic processing (i.e., a composite effect). Far less research, however, has been dedicated to the concept of gaze. Nonetheless, gaze perception is a substantial component of face and body perception, and holds critical information for everyday communicative interactions. Furthermore, the ability of human observers to detect direct versus averted eye gaze is effortless, perhaps similar to identity perception and emotion recognition. However, the hypothesis of holistic perception of eye gaze has never been tested directly. Research on gaze perception with the composite design could facilitate further systematic comparison with other aspects of face and body perception that have been investigated using the composite design (i.e., identity and emotion). In the present research, a composite design was administered to assess holistic processing of gaze cues in faces (Experiment 1) and bodies (Experiment 2). Results confirmed that eye and head orientation (Experiment 1A) and head and body orientation (Experiment 2A) are integrated in a holistic manner. However, the composite effect was not completely disrupted by inversion (Experiments 1B and 2B), a finding that will be discussed together with implications for future research.

Maintenance of Certification: How Performance in Practice Changes Improve Tobacco Cessation in Addiction Psychiatrists’ Practice

PubMed Central

Ford, James H.; Oliver, Karen A.; Giles, Miriam; Cates-Wessel, Kathryn; Krahn, Dean; Levin, Frances R.

2017-01-01

Background and Objectives In 2000, the American Board of Medical Specialties implemented the Maintenance of Certification (MOC), a structured process to help physicians identify and implement a quality improvement project to improve patient care. This study reports on findings from an MOC Performance in Practice (PIP) module designed and evaluated by addiction psychiatrists who are members of the American Academy of Addiction Psychiatry (AAAP). Method A 3-phase process was utilized to recruit AAAP members to participate in the study. The current study utilized data from 154 self-selected AAAP members who evaluated the effectiveness of the MOC Tobacco Cessation PIP. Results Of the physicians participating, 76% (n 120) completed the Tobacco PIP. A paired t-test analysis revealed that reported changes in clinical measure documentation were significant across all six measures. Targeted improvement efforts focused on a single clinical measure. Results found that simple change projects designed to improve clinical practice led to substantial changes in self-reported chart documentation for the selected measure. Conclusions The current findings suggest that addiction psychiatrists can leverage the MOC process to improve clinical care. PMID:27973746

Ti film deposition process of a plasma focus: Study by an experimental design

NASA Astrophysics Data System (ADS)

Inestrosa-Izurieta, M. J.; Moreno, J.; Davis, S.; Soto, L.

2017-10-01

The plasma generated by plasma focus (PF) devices have substantially different physical characteristics from another plasma, energetic ions and electrons, compared with conventional plasma devices used for plasma nanofabrication, offering new and unique opportunities in the processing and synthesis of Nanomaterials. This article presents the use of a plasma focus of tens of joules, PF-50J, for the deposition of materials sprayed from the anode by the plasma dynamics in the axial direction. This work focuses on the determination of the most significant effects of the technological parameters of the system on the obtained depositions through the use of a statistical experimental design. The results allow us to give a qualitative understanding of the Ti film deposition process in our PF device depending on four different events provoked by the plasma dynamics: i) an electric erosion of the outer material of the anode; ii) substrate ablation generating an interlayer; iii) electron beam deposition of material from the center of the anode; iv) heat load provoking clustering or even melting of the deposition surface.

Advanced Turbine Technology Applications Project (ATTAP)

NASA Technical Reports Server (NTRS)

1994-01-01

Reports technical effort by AlliedSignal Engines in sixth year of DOE/NASA funded project. Topics include: gas turbine engine design modifications of production APU to incorporate ceramic components; fabrication and processing of silicon nitride blades and nozzles; component and engine testing; and refinement and development of critical ceramics technologies, including: hot corrosion testing and environmental life predictive model; advanced NDE methods for internal flaws in ceramic components; and improved carbon pulverization modeling during impact. ATTAP project is oriented toward developing high-risk technology of ceramic structural component design and fabrication to carry forward to commercial production by 'bridging the gap' between structural ceramics in the laboratory and near-term commercial heat engine application. Current ATTAP project goal is to support accelerated commercialization of advanced, high-temperature engines for hybrid vehicles and other applications. Project objectives are to provide essential and substantial early field experience demonstrating ceramic component reliability and durability in modified, available, gas turbine engine applications; and to scale-up and improve manufacturing processes of ceramic turbine engine components and demonstrate application of these processes in the production environment.

Pump Design

NASA Technical Reports Server (NTRS)

1981-01-01

A NASA handbook on a general purpose titanium alloy was used by Sundstrand Corporation in design calculation for casting titanium impellers. Information contributed substantially to improved impeller design.

Production of substantially pure fructose

DOEpatents

Hatcher, Herbert J.; Gallian, John J.; Leeper, Stephen A.

1990-01-01

A process is disclosed for the production of substantially pure fructose from sucrose-containing substrates. The process comprises converting the sucrose to levan and glucose, purifying the levan by membrane technology, hydrolyzing the levan to form fructose monomers, and recovering the fructose.

Method and device for frictional welding

DOEpatents

Peacock, H.B.

1991-01-01

A method for friction welding that produces a seal having essentially no gas porosity, comprises two rotationally symmetric, generally cylindrical members, spaced apart and coaxially aligned, that are rotated with respect to each other and brought together under high pressure. One member is preferably a generally cylindrical cannister that stores uranium within its hollow walls. The other member is preferably a generally cylindrical, hollow weld ring. An annular channel formed in the weld ring functions as an internal flash trap and is uniquely designed so that substantially all of the welding flash generated from the friction welding is directed into the channel`s recessed bottom. Also, the channel design limits distortion of the two members during the friction welding, process, further contributing to the complete seal that is obtained.

Method and device for frictional welding

DOEpatents

Peacock, Harold B.

1992-01-01

A method for friction welding that produces a seal having essentially no gas porosity, comprises two rotationally symmetric, generally cylindrical members, spaced apart and coaxially aligned, that are rotated with respect to each other and brought together under high pressure. One member is preferably a generally cylindrical cannister that stores uranium within its hollow walls. The other member is preferably a generally cylindrical, hollow weld ring. An annular channel formed in the weld ring functions as an internal flash trap and is uniquely designed so that substantially all of the welding flash generated from the friction welding is directed into the channel's recessed bottom. Also, the channel design limits distortion of the two members during the friction welding process, further contributing to the complete seal that is obtained.

Interactive computer graphics - Why's, wherefore's and examples

NASA Technical Reports Server (NTRS)

Gregory, T. J.; Carmichael, R. L.

1983-01-01

The benefits of using computer graphics in design are briefly reviewed. It is shown that computer graphics substantially aids productivity by permitting errors in design to be found immediately and by greatly reducing the cost of fixing the errors and the cost of redoing the process. The possibilities offered by computer-generated displays in terms of information content are emphasized, along with the form in which the information is transferred. The human being is ideally and naturally suited to dealing with information in picture format, and the content rate in communication with pictures is several orders of magnitude greater than with words or even graphs. Since science and engineering involve communicating ideas, concepts, and information, the benefits of computer graphics cannot be overestimated.

Performance Ratings: Designs for Evaluating Their Validity and Accuracy.

DTIC Science & Technology

1986-07-01

ratees with substantial validity and with little bias due to the ethod for rating. Convergent validity and discriminant validity account for approximately...The expanded research design suggests that purpose for the ratings has little influence on the multitrait-multimethod properties of the ratings...Convergent and discriminant validity again account for substantial differences in the ratings of performance. Little method bias is present; both methods of

Heat transfer system

DOEpatents

Not Available

1980-03-07

A heat transfer system for a nuclear reactor is described. Heat transfer is accomplished within a sealed vapor chamber which is substantially evacuated prior to use. A heat transfer medium, which is liquid at the design operating temperatures, transfers heat from tubes interposed in the reactor primary loop to spaced tubes connected to a steam line for power generation purposes. Heat transfer is accomplished by a two-phase liquid-vapor-liquid process as used in heat pipes. Condensible gases are removed from the vapor chamber through a vertical extension in open communication with the chamber interior.

Isoreticular metal-organic frameworks, process for forming the same, and systematic design of pore size and functionality therein, with application for gas storage

DOEpatents

Yaghi, Omar M.; Eddaoudi, Mohamed; Li, Hailian; Kim, Jaheon; Rosi, Nathaniel

2005-08-16

An isoreticular metal-organic framework (IRMOF) and method for systematically forming the same. The method comprises the steps of dissolving at least one source of metal cations and at least one organic linking compound in a solvent to form a solution; and crystallizing the solution under predetermined conditions to form a predetermined IRMOF. At least one of functionality, dimension, pore size and free volume of the IRMOF is substantially determined by the organic linking compound.

Heat transfer system

DOEpatents

McGuire, Joseph C.

1982-01-01

A heat transfer system for a nuclear reactor. Heat transfer is accomplished within a sealed vapor chamber which is substantially evacuated prior to use. A heat transfer medium, which is liquid at the design operating temperatures, transfers heat from tubes interposed in the reactor primary loop to spaced tubes connected to a steam line for power generation purposes. Heat transfer is accomplished by a two-phase liquid-vapor-liquid process as used in heat pipes. Condensible gases are removed from the vapor chamber through a vertical extension in open communication with the chamber interior.

Expediency of wet-mix shotcreting in mines of Vostoktsvetmet

NASA Astrophysics Data System (ADS)

Shaposhnik, YuN

2018-03-01

This paper offers a substantiation of the transition from heavy and difficult-to-install steel frame support to the cheaper and simpler reinforced shotcrete lining (at the same bearing-capacity of the support). The process line for the preparation of the shotcrete mix is designed. The author of the paper presents calculation of the material inputs and labor costs of installation of different support types in Kazakhstan Mines. The economic efficiency of the wet-mix shotcrete spraying technology is illustrated in terms of Orlov and Artemevsk Mines.

Selecting optimal structure of burners for tubular cylindrical furnaces by the mathematical experiment planning method

NASA Astrophysics Data System (ADS)

Katin, Viktor; Kosygin, Vladimir; Akhtiamov, Midkhat

2017-10-01

This paper substantiates the method of mathematical planning for experimental research in the process of selecting the most efficient types of burning devices for tubular refinery furnaces of vertical-cylindrical design. This paper provides detailed consideration of an experimental plan of a 4×4 Latin square type when studying the impact of three factors with four levels of variance. On the basis of the experimental research we have developed practical recommendations on the employment of optimal burners for two-step fuel combustion.

Image science team

NASA Technical Reports Server (NTRS)

Ando, K.

1982-01-01

A substantial technology base of solid state pushbroom sensors exists and is in the process of further evolution at both GSFC and JPL. Technologies being developed relate to short wave infrared (SWIR) detector arrays; HgCdTe hybrid detector arrays; InSb linear and area arrays; passive coolers; spectral beam splitters; the deposition of spectral filters on detector arrays; and the functional design of the shuttle/space platform imaging spectrometer (SIS) system. Spatial and spectral characteristics of field, aircraft and space multispectral sensors are summaried. The status, field of view, and resolution of foreign land observing systems are included.

Artificial intelligence and design: Opportunities, research problems and directions

NASA Technical Reports Server (NTRS)

Amarel, Saul

1990-01-01

The issues of industrial productivity and economic competitiveness are of major significance in the U.S. at present. By advancing the science of design, and by creating a broad computer-based methodology for automating the design of artifacts and of industrial processes, we can attain dramatic improvements in productivity. It is our thesis that developments in computer science, especially in Artificial Intelligence (AI) and in related areas of advanced computing, provide us with a unique opportunity to push beyond the present level of computer aided automation technology and to attain substantial advances in the understanding and mechanization of design processes. To attain these goals, we need to build on top of the present state of AI, and to accelerate research and development in areas that are especially relevant to design problems of realistic complexity. We propose an approach to the special challenges in this area, which combines 'core work' in AI with the development of systems for handling significant design tasks. We discuss the general nature of design problems, the scientific issues involved in studying them with the help of AI approaches, and the methodological/technical issues that one must face in developing AI systems for handling advanced design tasks. Looking at basic work in AI from the perspective of design automation, we identify a number of research problems that need special attention. These include finding solution methods for handling multiple interacting goals, formation problems, problem decompositions, and redesign problems; choosing representations for design problems with emphasis on the concept of a design record; and developing approaches for the acquisition and structuring of domain knowledge with emphasis on finding useful approximations to domain theories. Progress in handling these research problems will have major impact both on our understanding of design processes and their automation, and also on several fundamental questions that are of intrinsic concern to AI. We present examples of current AI work on specific design tasks, and discuss new directions of research, both as extensions of current work and in the context of new design tasks where domain knowledge is either intractable or incomplete. The domains discussed include Digital Circuit Design, Mechanical Design of Rotational Transmissions, Design of Computer Architectures, Marine Design, Aircraft Design, and Design of Chemical Processes and Materials. Work in these domains is significant on technical grounds, and it is also important for economic and policy reasons.

Low Cost, Upper Stage-Class Propulsion

NASA Technical Reports Server (NTRS)

Vickers, John

2015-01-01

The low cost, upper stage-class propulsion (LCUSP) element will develop a high strength copper alloy additive manufacturing (AM) process as well as critical components for an upper stage-class propulsion system that will be demonstrated with testing. As manufacturing technologies have matured, it now appears possible to build all the major components and subsystems of an upper stage-class rocket engine for substantially less money and much faster than traditionally done. However, several enabling technologies must be developed before that can happen. This activity will address these technologies and demonstrate the concept by designing, manufacturing, and testing the critical components of a rocket engine. The processes developed and materials' property data will be transitioned to industry upon completion of the activity. Technologies to enable the concept are AM copper alloy process development, AM post-processing finishing to minimize surface roughness, AM material deposition on existing copper alloy substrate, and materials characterization.

Processes for treating cellulosic material

NASA Technical Reports Server (NTRS)

Kohlman, Karen L. (Inventor); Weil, Joseph R. (Inventor); Westgate, Paul L. (Inventor); Ladisch, Michael R. (Inventor); Yang, Yiqi (Inventor)

1998-01-01

Disclosed are processes for pretreating cellulosic materials in liquid water by heating the materials in liquid water at a temperature at or above their glass transition temperature but not substantially exceeding 220.degree. C., while maintaining the pH of the reaction medium in a range that avoids substantial autohydrolysis of the cellulosic materials. Such pretreatments minimize chemical changes to the cellulose while leading to physical changes which substantially increase susceptibility to hydrolysis in the presence of cellulase.

Preliminary design of an asteroid hopping mission

NASA Astrophysics Data System (ADS)

Scheppa, Michael D.

In 2010, NASA announced that its new vision is to support private space launch operations. It is anticipated that this new direction will create the need for new and innovative ideas that push the current boundaries of space exploration and contain the promise of substantial gain, both in research and capital. The purpose of the study is to plan and estimate the feasibility of a mission to visit a number of near Earth asteroids (NEAs). The mission would take place before the end of the 21st century, and would only use commercially available technology. Throughout the mission design process, while holding astronaut safety paramount, it was the goal to maximize the return while keeping the cost to a minimum. A mission of the nature would appeal to the private space industry because it could be easily adapted and set into motion. The mission design was divided into three main parts; mission timeline, vehicle design and power sources, with emphasis on nuclear and solar electric power, were investigated. The timeline and associated trajectories were initially selected using a numerical estimation and then optimized using Satellite Tool Kit (STK) 9.s's Design Explorer Optimizer [1]. Next, the spacecraft was design using commercially available parts that would support the mission requirements. The Variable Specific Impulse Magnetoplasma Rocket (VASIMR) was and instrumental piece in maximizing the number of NEAs visited. Once the spacecraft was designed, acceptable power supply options were investigated. The VASIMR VX-200 requires 200 kilowatts of power to maintain thrust. This creates the need for a substantial power supply that consists of either a nuclear reactor of massive solar arrays. STK 9.1's Design Explorer Optimizer was able to create a mission time line that allowed for the exploration of seven NEAs in under two years, while keeping the total mission DeltaV under 71 kilometers per second. Based on these initial findings, it is determined that a mission of this nature is feasible and would could greatly benefit the private space industry.

The software development process at the Chandra X-ray Center

NASA Astrophysics Data System (ADS)

Evans, Janet D.; Evans, Ian N.; Fabbiano, Giuseppina

2008-08-01

Software development for the Chandra X-ray Center Data System began in the mid 1990's, and the waterfall model of development was mandated by our documents. Although we initially tried this approach, we found that a process with elements of the spiral model worked better in our science-based environment. High-level science requirements are usually established by scientists, and provided to the software development group. We follow with review and refinement of those requirements prior to the design phase. Design reviews are conducted for substantial projects within the development team, and include scientists whenever appropriate. Development follows agreed upon schedules that include several internal releases of the task before completion. Feedback from science testing early in the process helps to identify and resolve misunderstandings present in the detailed requirements, and allows review of intangible requirements. The development process includes specific testing of requirements, developer and user documentation, and support after deployment to operations or to users. We discuss the process we follow at the Chandra X-ray Center (CXC) to develop software and support operations. We review the role of the science and development staff from conception to release of software, and some lessons learned from managing CXC software development for over a decade.

Summary of Liquid Oxygen/Hydrogen, Direct Metal Laser Sintering Injector Testing and Evaluation Effort at Marshall Space Flight Center

NASA Technical Reports Server (NTRS)

Barnett, Gregory; Bullard, David B.

2015-01-01

The last several years have witnessed a significant advancement in the area of additive manufacturing technology. One area that has seen substantial expansion in application has been laser sintering (or melting) in a powder bed. This technology is often termed 3D printing or various acronyms that may be industry, process, or company specific. Components manufactured via 3D printing have the potential to significantly reduce development and fabrication time and cost. The usefulness of 3D printed components is influenced by several factors such as material properties and surface roughness. This paper details three injectors that were designed, fabricated, and tested in order to evaluate the utility of 3D printed components for rocket engine applications. The three injectors were tested in a hot-fire environment with chamber pressures of approximately 1400 psia. One injector was a 28 element design printed by Directed Manufacturing. The other two injectors were identical 40 element designs printed by Directed Manufacturing and Solid Concepts. All the injectors were swirl-coaxial designs and were subscale versions of a full-scale injector currently in fabrication. The test and evaluation programs for the 28 element and 40 element injectors provided a substantial amount of data that confirms the feasibility of 3D printed parts for future applications. The operating conditions of previously tested, conventionally manufactured injectors were reproduced in the 28 and 40 element programs in order to contrast the performance of each. Overall, the 3D printed injectors demonstrated comparable performance to the conventionally manufactured units. The design features of the aforementioned injectors can readily be implemented in future applications with a high degree of confidence.

Next-Generation Intensity-Duration-Frequency Curves for Hydrologic Design in Snow-Dominated Environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, Hongxiang; Sun, Ning; Wigmosta, Mark

Precipitation-based intensity-duration-frequency (PREC-IDF) curves are a standard tool used to derive design floods for hydraulic infrastructure worldwide. In snow-dominated regions where a large percentage of flood events are caused by snowmelt and rain-on-snow events, the PREC-IDF design approach can lead to substantial underestimation/overestimation of design floods and associated infrastructure. In this study, next-generation IDF (NG-IDF) curves, which characterize the actual water reaching the land surface, are introduced into the design process to improve hydrologic design. The authors compared peak design flood estimates from the National Resource Conservation Service TR-55 hydrologic model driven by NG-IDF and PREC-IDF curves at 399 Snowpackmore » Telemetry (SNOTEL) stations across the western United States, all of which had at least 30 years of high-quality records. They found that about 72% of the stations in the western United States showed the potential for underdesign, for which the PREC-IDF curves underestimated peak design floods by as much as 324%. These results demonstrated the need to update the use of PREC-IDF curves to the use of NG-IDF curves for hydrologic design in snow-dominated regions.« less

Next-Generation Intensity‐Duration‐Frequency Curves for Hydrologic Design in Snow-Dominated Environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, Hongxiang; Sun, Ning; Wigmosta, Mark S.

Precipitation-based intensity-duration-frequency (PREC-IDF) curves are a standard tool used to derive design floods for hydraulic infrastructure worldwide. In snow-dominated regions where a large percentage of flood events are caused by snowmelt and rain-on-snow events, the PREC-IDF design approach can lead to substantial underestimation/overestimation of design floods and associated infrastructure. In this study, next-generation IDF (NG-IDF) curves, which characterize the actual water reaching the land surface, are introduced into the design process to improve hydrologic design. The authors compared peak design flood estimates from the National Resource Conservation Service TR-55 hydrologic model driven by NG-IDF and PREC-IDF curves at 399 Snowpackmore » Telemetry (SNOTEL) stations across the western United States, all of which had at least 30 years of high-quality records. They found that about 72% of the stations in the western United States showed the potential for underdesign, for which the PREC-IDF curves underestimated peak design floods by as much as 324%. These results demonstrated the need to update the use of PREC-IDF curves to the use of NG-IDF curves for hydrologic design in snow-dominated regions.« less

Development of an evaporation-based microfluidic sample concentrator

NASA Astrophysics Data System (ADS)

Sharma, Nigel R.; Lukyanov, Anatoly; Bardell, Ron L.; Seifried, Lynn; Shen, Mingchao

2008-02-01

MicroPlumbers Microsciences LLC, has developed a relatively simple concentrator device based on isothermal evaporation. The device allows for rapid concentration of dissolved or dispersed substances or microorganisms (e.g. bacteria, viruses, proteins, toxins, enzymes, antibodies, etc.) under conditions gentle enough to preserve their specific activity or viability. It is capable of removing of 0.8 ml of water per minute at 37°C, and has dimensions compatible with typical microfluidic devices. The concentrator can be used as a stand-alone device or integrated into various processes and analytical instruments, substantially increasing their sensitivity while decreasing processing time. The evaporative concentrator can find applications in many areas such as biothreat detection, environmental monitoring, forensic medicine, pathogen analysis, and agricultural industrial monitoring. In our presentation, we describe the design, fabrication, and testing of the concentrator. We discuss multiphysics simulations of the heat and mass transport in the device that we used to select the design of the concentrator and the protocol of performance testing. We present the results of experiments evaluating water removal performance.

Studies of the air plasma spraying of zirconia powder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Varacalle, D.J. Jr.; Wilson, G.C.; Crawmer, D.E.

As part of an investigation of the dynamics that occur in the air plasma spray process, an experimental and analytical study has been accomplished for the deposition of yttria-stabilized zirconia powder using argon-hydrogen and argon-helium working gases. Numerical models of the plasma dynamics and the related plasma-particle interaction are presented. The analytical studies were conducted to determine the parameter space for the empirical studies. Experiments were then conducted using a Box statistical design-of-experiment approach. A substantial range of plasma processing conditions and their effect on the resultant coating is presented. The coatings were characterized by hardness tests and optical metallographymore » (i.e., image analysis). Coating qualities are discussed with respect to hardness, porosity, surface roughness, deposition efficiency, and microstructure. Attributes of the coatings are correlated with the changes in operating parameters. An optimized coating design predicted by the SDE analysis and verified by the calculations is also presented.« less

Generalized railway tank car safety design optimization for hazardous materials transport: addressing the trade-off between transportation efficiency and safety.

PubMed

Saat, Mohd Rapik; Barkan, Christopher P L

2011-05-15

North America railways offer safe and generally the most economical means of long distance transport of hazardous materials. Nevertheless, in the event of a train accident releases of these materials can pose substantial risk to human health, property or the environment. The majority of railway shipments of hazardous materials are in tank cars. Improving the safety design of these cars to make them more robust in accidents generally increases their weight thereby reducing their capacity and consequent transportation efficiency. This paper presents a generalized tank car safety design optimization model that addresses this tradeoff. The optimization model enables evaluation of each element of tank car safety design, independently and in combination with one another. We present the optimization model by identifying a set of Pareto-optimal solutions for a baseline tank car design in a bicriteria decision problem. This model provides a quantitative framework for a rational decision-making process involving tank car safety design enhancements to reduce the risk of transporting hazardous materials. Copyright © 2011 Elsevier B.V. All rights reserved.

Lightning Simulation and Design Program (LSDP)

NASA Astrophysics Data System (ADS)

Smith, D. A.

This computer program simulates a user-defined lighting configuration. It has been developed as a tool to aid in the design of exterior lighting systems. Although this program is used primarily for perimeter security lighting design, it has potential use for any application where the light can be approximated by a point source. A data base of luminaire photometric information is maintained for use with this program. The user defines the surface area to be illuminated with a rectangular grid and specifies luminaire positions. Illumination values are calculated for regularly spaced points in that area and isolux contour plots are generated. The numerical and graphical output for a particular site mode are then available for analysis. The amount of time spent on point-to-point illumination computation with this progress is much less than that required for tedious hand calculations. The ease with which various parameters can be interactively modified with the progress also reduces the time and labor expended. Consequently, the feasibility of design ideas can be examined, modified, and retested more thoroughly, and overall design costs can be substantially lessened by using this progress as an adjunct to the design process.

First 65nm tape-out using inverse lithography technology (ILT)

NASA Astrophysics Data System (ADS)

Hung, Chi-Yuan; Zhang, Bin; Tang, Deming; Guo, Eric; Pang, Linyong; Liu, Yong; Moore, Andrew; Wang, Kechang

2005-11-01

This paper presents SMIC's first 65nm tape out results, in particularly, using ILT. ILT mathematically determines the mask features that produce the desired on-wafer results with best wafer pattern fidelity, largest process window or both. SMIC applied it to its first 65nm tape-out to study ILT performance and benefits for deep sub-wavelength lithography. SMIC selected 3 SRAM designs as the first test case, because SRAM bit-cells contain features which are challenging lithographically. Mask patterns generated from both conventional OPC and ILT were placed on the mask side-by-side. Mask manufacturability (including fracturing, writing time, inspection, and metrology) and wafer print performance of ILT were studied. The results demonstrated that ILT achieved better CD accuracy, produced substantially larger process window than conventional OPC, and met SMIC's 65nm process window requirements.

Behaviors of printed circuit boards due to microwave supported curing process of coating materials.

PubMed

Bremerkamp, Felix; Nowottnick, Mathias; Seehase, Dirk; Bui, Trinh Dung

2012-01-01

The Application of a microwave supported curing process for coatings in the field of electronic industry poses a challenge. Here the implementation of this technology is represented. Within the scope of the investigation special PCB Test Layouts were designed and the polymer curing process examined by the method of dielectric analysis. Furthermore the coupling of microwave radiation with conductive PCB structures was analyzed experimentally by means of special test boards. The formation of standing waves and regular heating distribution along the conductive wires on the PCB could be observed. The experimental results were compared with numerical simulation. In this context the numerical analysis of microwave PCB interaction led to important findings concerning wave propagation on wired PCB. The final valuation demonstrated a substantial similarity between numerical simulations and experimental results.

Software Package Completed for Alloy Design at the Atomic Level

NASA Technical Reports Server (NTRS)

Bozzolo, Guillermo H.; Noebe, Ronald D.; Abel, Phillip B.; Good, Brian S.

2001-01-01

As a result of a multidisciplinary effort involving solid-state physics, quantum mechanics, and materials and surface science, the first version of a software package dedicated to the atomistic analysis of multicomponent systems was recently completed. Based on the BFS (Bozzolo, Ferrante, and Smith) method for the calculation of alloy and surface energetics, this package includes modules devoted to the analysis of many essential features that characterize any given alloy or surface system, including (1) surface structure analysis, (2) surface segregation, (3) surface alloying, (4) bulk crystalline material properties and atomic defect structures, and (5) thermal processes that allow us to perform phase diagram calculations. All the modules of this Alloy Design Workbench 1.0 (ADW 1.0) are designed to run in PC and workstation environments, and their operation and performance are substantially linked to the needs of the user and the specific application.

Major design issues of molten carbonate fuel cell power generation unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, T.P.

1996-04-01

In addition to the stack, a fuel cell power generation unit requires fuel desulfurization and reforming, fuel and oxidant preheating, process heat removal, waste heat recovery, steam generation, oxidant supply, power conditioning, water supply and treatment, purge gas supply, instrument air supply, and system control. These support facilities add considerable cost and system complexity. Bechtel, as a system integrator of M-C Power`s molten carbonate fuel cell development team, has spent substantial effort to simplify and minimize these supporting facilities to meet cost and reliability goals for commercialization. Similiar to other fuels cells, MCFC faces design challenge of how to complymore » with codes and standards, achieve high efficiency and part load performance, and meanwhile minimize utility requirements, weight, plot area, and cost. However, MCFC has several unique design issues due to its high operating temperature, use of molten electrolyte, and the requirement of CO2 recycle.« less

Fluidized bed selective pyrolysis of coal

DOEpatents

Shang, J.Y.; Cha, C.Y.; Merriam, N.W.

1992-12-15

The present invention discloses a process for the pyrolysis of coal which comprises the effective utilization of two zonal inclined fluidized beds, where said zones can be selectively controlled as to temperature and heating rate. The first zonal inclined fluidized bed serves as a dryer for crushed coal and additionally is controlled to selectively pyrolyze said coal producing substantially carbon dioxide for recycle use. The second zonal inclined fluidized bed further pyrolyses the coal to gaseous, liquid and char products under controlled temperature and heating rate zones designed to economically integrate the product mix. The gas and liquid products are recovered from the gaseous effluent stream while the char which remains can be further treated or utilized in a subsequent process step. 9 figs.

Fluidized bed selective pyrolysis of coal

DOEpatents

Shang, Jer Y.; Cha, Chang Y.; Merriam, Norman W.

1992-01-01

The present invention discloses a process for the pyrolysis of coal which comprises the effective utilization of two zonal inclined fluidized beds, where said zones can be selectively controlled as to temperature and heating rate. The first zonal inclined fluidized bed serves as a dryer for crushed coal and additionally is controlled to selectively pyrolyze said coal producing substantially carbon dioxide for recycle use. The second zonal inclined fluidized bed further pyrolyzes the coal to gaseous, liquid and char products under controlled temperature and heating rate zones designed to economically integrate the product mix. The gas and liquid products are recovered from the gaseous effluent stream while the char which remains can be further treated or utilized in a subsequent process step.

Advanced in-duct sorbent injection for SO{sub 2} control. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stouffer, M.R.; Withium, J.A.; Rosenhoover, W.A.

1994-12-01

The objective of this research project was to develop a second generation duct sorbent injection technology as a cost-effective compliance option for the 1990 Clean Air Act Amendments. Research and development work was focused on the Advanced Coolside process, which showed the potential for exceeding the original performance targets of 90% SO{sub 2} removal and 60% sorbent utilization. Process development was conducted in a 1000 acfm pilot plant. The pilot plant testing showed that the Advanced Coolside process can achieve 90% SO{sub 2} removal at sorbent utilizations up to 75%. The testing also showed that the process has the potentialmore » to achieve very high removal efficiency (90 to >99%). By conducting conceptual process design and economic evaluations periodically during the project, development work was focused on process design improvements which substantially lowered process capital and operating costs, A final process economic study projects capital costs less than one half of those for limestone forced oxidation wet FGD. Projected total SO{sub 2} control cost is about 25% lower than wet FGD for a 260 MWe plant burning a 2.5% sulfur coal. A waste management study showed the acceptability of landfill disposal; it also identified a potential avenue for by-product utilization which should be further investigated. Based on the pilot plant performance and on the above economic projections, future work to scale up the Advanced Coolside process is recommended.« less

Testbed Experiment for SPIDER: A Photonic Integrated Circuit-based Interferometric imaging system

NASA Astrophysics Data System (ADS)

Badham, K.; Duncan, A.; Kendrick, R. L.; Wuchenich, D.; Ogden, C.; Chriqui, G.; Thurman, S. T.; Su, T.; Lai, W.; Chun, J.; Li, S.; Liu, G.; Yoo, S. J. B.

The Lockheed Martin Advanced Technology Center (LM ATC) and the University of California at Davis (UC Davis) are developing an electro-optical (EO) imaging sensor called SPIDER (Segmented Planar Imaging Detector for Electro-optical Reconnaissance) that seeks to provide a 10x to 100x size, weight, and power (SWaP) reduction alternative to the traditional bulky optical telescope and focal-plane detector array. The substantial reductions in SWaP would reduce cost and/or provide higher resolution by enabling a larger-aperture imager in a constrained volume. Our SPIDER imager replaces the traditional optical telescope and digital focal plane detector array with a densely packed interferometer array based on emerging photonic integrated circuit (PIC) technologies that samples the object being imaged in the Fourier domain (i.e., spatial frequency domain), and then reconstructs an image. Our approach replaces the large optics and structures required by a conventional telescope with PICs that are accommodated by standard lithographic fabrication techniques (e.g., complementary metal-oxide-semiconductor (CMOS) fabrication). The standard EO payload integration and test process that involves precision alignment and test of optical components to form a diffraction limited telescope is, therefore, replaced by in-process integration and test as part of the PIC fabrication, which substantially reduces associated schedule and cost. In this paper we describe the photonic integrated circuit design and the testbed used to create the first images of extended scenes. We summarize the image reconstruction steps and present the final images. We also describe our next generation PIC design for a larger (16x area, 4x field of view) image.

Therapeutic assessment for preadolescent boys with oppositional defiant disorder: a replicated single-case time-series design.

PubMed

Smith, Justin D; Handler, Leonard; Nash, Michael R

2010-09-01

The Therapeutic Assessment (TA) model is a relatively new treatment approach that fuses assessment and psychotherapy. The study examines the efficacy of this model with preadolescent boys with oppositional defiant disorder and their families. A replicated single-case time-series design with daily measures is used to assess the effects of TA and to track the process of change as it unfolds. All 3 families benefitted from participation in TA across multiple domains of functioning, but the way in which change unfolded was unique for each family. These findings are substantiated by the Behavior Assessment System for Children (Reynolds & Kamphaus, 2004). The TA model is shown to be an effective treatment for preadolescent boys with oppositional defiant disorder and their families. Further, the time-series design of this study illustrated how this empirically grounded case-based methodology reveals when and how change unfolds during treatment in a way that is usually not possible with other research designs.

Design of a superconducting volume coil for magnetic resonance microscopy of the mouse brain

NASA Astrophysics Data System (ADS)

Nouls, John C.; Izenson, Michael G.; Greeley, Harold P.; Johnson, G. Allan

2008-04-01

We present the design process of a superconducting volume coil for magnetic resonance microscopy of the mouse brain at 9.4 T. The yttrium barium copper oxide coil has been designed through an iterative process of three-dimensional finite-element simulations and validation against room temperature copper coils. Compared to previous designs, the Helmholtz pair provides substantially higher B1 homogeneity over an extended volume of interest sufficiently large to image biologically relevant specimens. A custom-built cryogenic cooling system maintains the superconducting probe at 60 ± 0.1 K. Specimen loading and probe retuning can be carried out interactively with the coil at operating temperature, enabling much higher through-put. The operation of the probe is a routine, consistent procedure. Signal-to-noise ratio in a mouse brain increased by a factor ranging from 1.1 to 2.9 as compared to a room-temperature solenoid coil optimized for mouse brain microscopy. We demonstrate images encoded at 10 × 10 × 20 μm for an entire mouse brain specimen with signal-to-noise ratio of 18 and a total acquisition time of 16.5 h, revealing neuroanatomy unseen at lower resolution. Phantom measurements show an effective spatial resolution better than 20 μm.

Design of a superconducting volume coil for magnetic resonance microscopy of the mouse brain.

PubMed

Nouls, John C; Izenson, Michael G; Greeley, Harold P; Johnson, G Allan

2008-04-01

We present the design process of a superconducting volume coil for magnetic resonance microscopy of the mouse brain at 9.4T. The yttrium barium copper oxide coil has been designed through an iterative process of three-dimensional finite-element simulations and validation against room temperature copper coils. Compared to previous designs, the Helmholtz pair provides substantially higher B(1) homogeneity over an extended volume of interest sufficiently large to image biologically relevant specimens. A custom-built cryogenic cooling system maintains the superconducting probe at 60+/-0.1K. Specimen loading and probe retuning can be carried out interactively with the coil at operating temperature, enabling much higher through-put. The operation of the probe is a routine, consistent procedure. Signal-to-noise ratio in a mouse brain increased by a factor ranging from 1.1 to 2.9 as compared to a room-temperature solenoid coil optimized for mouse brain microscopy. We demonstrate images encoded at 10x10x20mum for an entire mouse brain specimen with signal-to-noise ratio of 18 and a total acquisition time of 16.5h, revealing neuroanatomy unseen at lower resolution. Phantom measurements show an effective spatial resolution better than 20mum.

Compact sieve-tray distillation column for ammonia-water absorption heat pump: Part 1 -- Design methodology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anand, G.; Erickson, D.C.

1999-07-01

The distillation column is a key component of ammonia-water absorption units including advanced generator-absorber heat exchange (GAX) cycle heat pumps. The design of the distillation column is critical to unit performance, size, and cost. The distillation column can be designed with random packing, structured packing, or various tray configurations. A sieve-tray distillation column is the least complicated tray design and is less costly than high-efficiency packing. Substantial literature is available on sieve tray design and performance. However, most of the correlations and design recommendations were developed for large industrial hydrocarbon systems and are generally not directly applicable to the compactmore » ammonia-water column discussed here. The correlations were reviewed and modified as appropriate for this application, and a sieve-tray design model was developed. This paper presents the sieve-tray design methodology for highly compact ammonia-water columns. A conceptual design of the distillation column for an 8 ton vapor exchange (VX) GAX heat pump is presented, illustrating relevant design parameters and trends. The design process revealed several issues that have to be investigated experimentally to design the final optimized rectifier. Validation of flooding and weeping limits and tray/point efficiencies are of primary importance.« less

Process improvement methods increase the efficiency, accuracy, and utility of a neurocritical care research repository.

PubMed

O'Connor, Sydney; Ayres, Alison; Cortellini, Lynelle; Rosand, Jonathan; Rosenthal, Eric; Kimberly, W Taylor

2012-08-01

Reliable and efficient data repositories are essential for the advancement of research in Neurocritical care. Various factors, such as the large volume of patients treated within the neuro ICU, their differing length and complexity of hospital stay, and the substantial amount of desired information can complicate the process of data collection. We adapted the tools of process improvement to the data collection and database design of a research repository for a Neuroscience intensive care unit. By the Shewhart-Deming method, we implemented an iterative approach to improve the process of data collection for each element. After an initial design phase, we re-evaluated all data fields that were challenging or time-consuming to collect. We then applied root-cause analysis to optimize the accuracy and ease of collection, and to determine the most efficient manner of collecting the maximal amount of data. During a 6-month period, we iteratively analyzed the process of data collection for various data elements. For example, the pre-admission medications were found to contain numerous inaccuracies after comparison with a gold standard (sensitivity 71% and specificity 94%). Also, our first method of tracking patient admissions and discharges contained higher than expected errors (sensitivity 94% and specificity 93%). In addition to increasing accuracy, we focused on improving efficiency. Through repeated incremental improvements, we reduced the number of subject records that required daily monitoring from 40 to 6 per day, and decreased daily effort from 4.5 to 1.5 h/day. By applying process improvement methods to the design of a Neuroscience ICU data repository, we achieved a threefold improvement in efficiency and increased accuracy. Although individual barriers to data collection will vary from institution to institution, a focus on process improvement is critical to overcoming these barriers.

Maintaining evaluation designs in long term community based health promotion programmes: Heartbeat Wales case study.

PubMed Central

Nutbeam, D; Smith, C; Murphy, S; Catford, J

1993-01-01

STUDY OBJECTIVE--To examine the difficulties of developing and maintaining outcome evaluation designs in long term, community based health promotion programmes. DESIGN--Semistructured interviews of health promotion managers. SETTING--Wales and two reference health regions in England. PARTICIPANTS--Nine health promotion managers in Wales and 18 in England. MEASUREMENTS AND MAIN RESULTS--Information on selected heart health promotion activity undertaken or coordinated by health authorities from 1985-90 was collected. The Heartbeat Wales coronary heart disease prevention programme was set up in 1985, and a research and evaluation strategy was established to complement the intervention. A substantial increase in the budget occurred over the period. In the reference health regions in England this initiative was noted and rapidly taken up, thus compromising their use as control areas. CONCLUSION--Information on large scale, community based health promotion programmes can disseminate quickly and interfere with classic intervention/evaluation control designs through contamination. Alternative experimental designs for assessing the effectiveness of long term intervention programmes need to be considered. These should not rely solely on the use of reference populations, but should balance the measurement of outcome with an assessment of the process of change in communities. The development and use of intervention exposure measures together with well structured and comprehensive process evaluation in both the intervention and reference areas is recommended. PMID:8326270

Method and device for frictional welding

DOEpatents

Peacock, H.B.

1992-10-13

A method is described for friction welding that produces a seal having essentially no gas porosity, comprises two rotationally symmetric, generally cylindrical members, spaced apart and coaxially aligned, that are rotated with respect to each other and brought together under high pressure. One member is preferably a generally cylindrical canister that stores uranium within its hollow walls. The other member is preferably a generally cylindrical, hollow weld ring. An annular channel formed in the weld ring functions as an internal flash trap and is uniquely designed so that substantially all of the welding flash generated from the friction welding is directed into the channel's recessed bottom. Also, the channel design limits distortion of the two members during the friction welding process, further contributing to the complete seal that is obtained. 5 figs.

Ultrathin metasurface with high absorptance for waterborne sound

NASA Astrophysics Data System (ADS)

Mei, Jun; Zhang, Xiujuan; Wu, Ying

2018-03-01

We present a design for an acoustic metasurface which can efficiently absorb low-frequency sound energy in water. The metasurface has a simple structure and consists of only two common materials: i.e., water and silicone rubber. The optimized material and geometrical parameters of the designed metasurface are determined by an analytic formula in conjunction with an iterative process based on the retrieval method. Although the metasurface is as thin as 0.15 of the wavelength, it can absorb 99.7% of the normally incident sound wave energy. Furthermore, the metasurface maintains a substantially high absorptance over a relatively broad bandwidth, and also works well for oblique incidence with an incident angle of up to 50°. Potential applications in the field of underwater sound isolation are expected.

A new method of search design of refrigerating systems containing a liquid and gaseous working medium based on the graph model of the physical operating principle

NASA Astrophysics Data System (ADS)

Yakovlev, A. A.; Sorokin, V. S.; Mishustina, S. N.; Proidakova, N. V.; Postupaeva, S. G.

2017-01-01

The article describes a new method of search design of refrigerating systems, the basis of which is represented by a graph model of the physical operating principle based on thermodynamical description of physical processes. The mathematical model of the physical operating principle has been substantiated, and the basic abstract theorems relatively semantic load applied to nodes and edges of the graph have been represented. The necessity and the physical operating principle, sufficient for the given model and intended for the considered device class, were demonstrated by the example of a vapour-compression refrigerating plant. The example of obtaining a multitude of engineering solutions of a vapour-compression refrigerating plant has been considered.

Designer BHAs reduce costs on Andrew/Cyrus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klein, R.; Todd, S.; Clark, G.

1997-10-01

A key mechanism to development of Andrew/Cyrus has been the development of alliances between BP Exploration, its field partners and various contractors. One such joint venture was the well engineering alliance between BP, Schlumberger, Baker Hughes INTEQ and Transocean, created to deliver five predrilled horizontal wells in the two fields prior to Andrew platform installation. This alliance provided the opportunity to radically change usual ways of doing business in the well engineering arena. One specific aspect involved a rigorous learning process within the team. Rapid learning before and during the operation led to several substantial improvements, one of which wasmore » the development of designer bottomhole assembly (BHA) configurations. Continual development of these assemblies has optimized well placement, bringing enhanced value while reducing costs and increasing potential alliance gainshare.« less

Comminution process to produce engineered wood particles of uniform size and shape with disrupted grain structure from veneer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dooley, James H; Lanning, David N

Comminution process of wood veneer to produce wood particles, by feeding wood veneer in a direction of travel substantially normal to grain through a counter rotating pair of intermeshing arrays of cutting discs arrayed axially perpendicular to the direction of veneer travel, wherein the cutting discs have a uniform thickness (Td), to produce wood particles characterized by a length dimension (L) substantially equal to the Td and aligned substantially parallel to grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) substantially equal to the veneer thickness (Tv) and aligned normal to Wmore » and L, wherein the W.times.H dimensions define a pair of substantially parallel end surfaces with end checking between crosscut fibers.« less

OUT Success Stories: Advanced Airfoils for Wind Turbines

DOE R&D Accomplishments Database

Jones, J.; Green, B.

2000-08-01

New airfoils have substantially increased the aerodynamic efficiency of wind turbines. It is clear that these new airfoils substantially increased energy output from wind turbines. Virtually all new blades built in this country today use these advanced airfoil designs.

Developing a Decision Support System for Tobacco Use Counseling Using Primary Care Physicians

PubMed Central

Marcy, Theodore W.; Kaplan, Bonnie; Connolly, Scott W.; Michel, George; Shiffman, Richard N.; Flynn, Brian S.

2009-01-01

Background Clinical decision support systems (CDSS) have the potential to improve adherence to guidelines, but only if they are designed to work in the complex environment of ambulatory clinics as otherwise physicians may not use them. Objective To gain input from primary care physicians in designing a CDSS for smoking cessation to ensure that the design is appropriate to a clinical environment before attempts to test this CDSS in a clinical trial. This approach is of general interest to those designing similar systems. Design and Approach We employed an iterative ethnographic process that used multiple evaluation methods to understand physician preferences and workflow integration. Using results from our prior survey of physicians and clinic managers, we developed a prototype CDSS, validated content and design with an expert panel, and then subjected it to usability testing by physicians, followed by iterative design changes based on their feedback. We then performed clinical testing with individual patients, and conducted field tests of the CDSS in two primary care clinics during which four physicians used it for routine patient visits. Results The CDSS prototype was substantially modified through these cycles of usability and clinical testing, including removing a potentially fatal design flaw. During field tests in primary care clinics, physicians incorporated the final CDSS prototype into their workflow, and used it to assist in smoking cessation interventions up to eight times daily. Conclusions A multi-method evaluation process utilizing primary care physicians proved useful for developing a CDSS that was acceptable to physicians and patients, and feasible to use in their clinical environment. PMID:18713526

Conceptual design for aerospace vehicles

NASA Technical Reports Server (NTRS)

Gratzer, Louis B.

1989-01-01

The designers of aircraft and more recently, aerospace vehicles have always struggled with the problems of evolving their designs to produce a machine which would perform its assigned task(s) in some optimum fashion. Almost invariably this involved dealing with more variables and constraints than could be handled in any computationally feasible way. With the advent of the electronic digital computer, the possibilities for introducing more variable and constraints into the initial design process led to greater expectations for improvement in vehicle (system) efficiency. The creation of the large scale systems necessary to achieve optimum designs has, for many reason, proved to be difficult. From a technical standpoint, significant problems arise in the development of satisfactory algorithms for processing of data from the various technical disciplines in a way that would be compatible with the complex optimization function. Also, the creation of effective optimization routines for multi-variable and constraint situations which could lead to consistent results has lagged. The current capability for carrying out the conceptual design of an aircraft on an interdisciplinary bases was evaluated to determine the need for extending this capability, and if necessary, to recommend means by which this could be carried out. Based on a review of available documentation and individual consultations, it appears that there is extensive interest at Langley Research Center as well as in the aerospace community in providing a higher level of capability that meets the technical challenges. By implication, the current design capability is inadequate and it does not operate in a way that allows the various technical disciplines to participate and cooperately interact in the design process. Based on this assessment, it was concluded that substantial effort should be devoted to developing a computer-based conceptual design system that would provide the capability needed for the near-term as well as framework for development of more advanced methods to serve future needs.

Design Environment for Multifidelity and Multidisciplinary Components

NASA Technical Reports Server (NTRS)

Platt, Michael

2014-01-01

One of the greatest challenges when developing propulsion systems is predicting the interacting effects between the fluid loads, thermal loads, and structural deflection. The interactions between technical disciplines often are not fully analyzed, and the analysis in one discipline often uses a simplified representation of other disciplines as an input or boundary condition. For example, the fluid forces in an engine generate static and dynamic rotor deflection, but the forces themselves are dependent on the rotor position and its orbit. It is important to consider the interaction between the physical phenomena where the outcome of each analysis is heavily dependent on the inputs (e.g., changes in flow due to deflection, changes in deflection due to fluid forces). A rigid design process also lacks the flexibility to employ multiple levels of fidelity in the analysis of each of the components. This project developed and validated an innovative design environment that has the flexibility to simultaneously analyze multiple disciplines and multiple components with multiple levels of model fidelity. Using NASA's open-source multidisciplinary design analysis and optimization (OpenMDAO) framework, this multifaceted system will provide substantially superior capabilities to current design tools.

Multi-Stage Hybrid Rocket Conceptual Design for Micro-Satellites Launch using Genetic Algorithm

NASA Astrophysics Data System (ADS)

Kitagawa, Yosuke; Kitagawa, Koki; Nakamiya, Masaki; Kanazaki, Masahiro; Shimada, Toru

The multi-objective genetic algorithm (MOGA) is applied to the multi-disciplinary conceptual design problem for a three-stage launch vehicle (LV) with a hybrid rocket engine (HRE). MOGA is an optimization tool used for multi-objective problems. The parallel coordinate plot (PCP), which is a data mining method, is employed in the post-process in MOGA for design knowledge discovery. A rocket that can deliver observing micro-satellites to the sun-synchronous orbit (SSO) is designed. It consists of an oxidizer tank containing liquid oxidizer, a combustion chamber containing solid fuel, a pressurizing tank and a nozzle. The objective functions considered in this study are to minimize the total mass of the rocket and to maximize the ratio of the payload mass to the total mass. To calculate the thrust and the engine size, the regression rate is estimated based on an empirical model for a paraffin (FT-0070) propellant. Several non-dominated solutions are obtained using MOGA, and design knowledge is discovered for the present hybrid rocket design problem using a PCP analysis. As a result, substantial knowledge on the design of an LV with an HRE is obtained for use in space transportation.

Boundary formulations for sensitivity analysis without matrix derivatives

NASA Technical Reports Server (NTRS)

Kane, J. H.; Guru Prasad, K.

1993-01-01

A new hybrid approach to continuum structural shape sensitivity analysis employing boundary element analysis (BEA) is presented. The approach uses iterative reanalysis to obviate the need to factor perturbed matrices in the determination of surface displacement and traction sensitivities via a univariate perturbation/finite difference (UPFD) step. The UPFD approach makes it possible to immediately reuse existing subroutines for computation of BEA matrix coefficients in the design sensitivity analysis process. The reanalysis technique computes economical response of univariately perturbed models without factoring perturbed matrices. The approach provides substantial computational economy without the burden of a large-scale reprogramming effort.

Application of NX Siemens PLM software in educational process in preparing students of engineering branch

NASA Astrophysics Data System (ADS)

Sadchikova, G. M.

2017-01-01

This article discusses the results of the introduction of computer-aided design NX by Siemens Plm Software to the classes of a higher education institution. The necessity of application of modern information technologies in teaching students of engineering profile and selection of a software product is substantiated. The author describes stages of the software module study in relation to some specific courses, considers the features of NX software, which require the creation of standard and unified product databases. The article also gives examples of research carried out by the students with the various software modules.

An intelligent advisor for the design manager

NASA Technical Reports Server (NTRS)

Rogers, James L.; Padula, Sharon L.

1989-01-01

A design problem is viewed as a complex system divisible into modules. Before the design of a complex system can begin, much time and money are spent in determining the couplings among modules and the presence of iterative loops. This is important because the design manager must know how to group the modules into substems and how to assign subsystems to design teams so that changes in one subsystem will have predictable effects on other subsystems. Determining these subsystems is not an easy, straightforward process and often important couplings are overlooked. Moreover, the planning task must be repeated as new information becomes available or as the design specifications change. The purchase of this research effort is to develop a knowledge-based tool to act as an intelligent advisor for the design manager. This tool identifies the subsystems of a complex design problem, orders them into a well-structured format, and marks the couplings among the subsystems to facilitate the use of multilevel tools. The tool was tested in the decomposition of the COFS (Control of Flexible Structures) mast design which has about 50 modules. This test indicated that this type of approach could lead to a substantial savings by organizing and displaying a complex problem as a sequence of subsystems easily divisible among design teams.

Comparing Proteolytic Fingerprints of Antigen-Presenting Cells during Allergen Processing.

PubMed

Hofer, Heidi; Weidinger, Tamara; Briza, Peter; Asam, Claudia; Wolf, Martin; Twaroch, Teresa E; Stolz, Frank; Neubauer, Angela; Dall, Elfriede; Hammerl, Peter; Jacquet, Alain; Wallner, Michael

2017-06-08

Endolysosomal processing has a critical influence on immunogenicity as well as immune polarization of protein antigens. In industrialized countries, allergies affect around 25% of the population. For the rational design of protein-based allergy therapeutics for immunotherapy, a good knowledge of T cell-reactive regions on allergens is required. Thus, we sought to analyze endolysosomal degradation patterns of inhalant allergens. Four major allergens from ragweed, birch, as well as house dust mites were produced as recombinant proteins. Endolysosomal proteases were purified by differential centrifugation from dendritic cells, macrophages, and B cells, and combined with allergens for proteolytic processing. Thereafter, endolysosomal proteolysis was monitored by protein gel electrophoresis and mass spectrometry. We found that the overall proteolytic activity of specific endolysosomal fractions differed substantially, whereas the degradation patterns of the four model allergens obtained with the different proteases were extremely similar. Moreover, previously identified T cell epitopes were assigned to endolysosomal peptides and indeed showed a good overlap with known T cell epitopes for all four candidate allergens. Thus, we propose that the degradome assay can be used as a predictor to determine antigenic peptides as potential T cell epitopes, which will help in the rational design of protein-based allergy vaccine candidates.

Comparing Proteolytic Fingerprints of Antigen-Presenting Cells during Allergen Processing

PubMed Central

Hofer, Heidi; Weidinger, Tamara; Briza, Peter; Asam, Claudia; Wolf, Martin; Twaroch, Teresa E.; Stolz, Frank; Neubauer, Angela; Dall, Elfriede; Hammerl, Peter; Jacquet, Alain; Wallner, Michael

2017-01-01

Endolysosomal processing has a critical influence on immunogenicity as well as immune polarization of protein antigens. In industrialized countries, allergies affect around 25% of the population. For the rational design of protein-based allergy therapeutics for immunotherapy, a good knowledge of T cell-reactive regions on allergens is required. Thus, we sought to analyze endolysosomal degradation patterns of inhalant allergens. Four major allergens from ragweed, birch, as well as house dust mites were produced as recombinant proteins. Endolysosomal proteases were purified by differential centrifugation from dendritic cells, macrophages, and B cells, and combined with allergens for proteolytic processing. Thereafter, endolysosomal proteolysis was monitored by protein gel electrophoresis and mass spectrometry. We found that the overall proteolytic activity of specific endolysosomal fractions differed substantially, whereas the degradation patterns of the four model allergens obtained with the different proteases were extremely similar. Moreover, previously identified T cell epitopes were assigned to endolysosomal peptides and indeed showed a good overlap with known T cell epitopes for all four candidate allergens. Thus, we propose that the degradome assay can be used as a predictor to determine antigenic peptides as potential T cell epitopes, which will help in the rational design of protein-based allergy vaccine candidates. PMID:28594355

Reconfigurable nanoscale spin-wave directional coupler

PubMed Central

Wang, Qi; Pirro, Philipp; Verba, Roman; Slavin, Andrei; Hillebrands, Burkard; Chumak, Andrii V.

2018-01-01

Spin waves, and their quanta magnons, are prospective data carriers in future signal processing systems because Gilbert damping associated with the spin-wave propagation can be made substantially lower than the Joule heat losses in electronic devices. Although individual spin-wave signal processing devices have been successfully developed, the challenging contemporary problem is the formation of two-dimensional planar integrated spin-wave circuits. Using both micromagnetic modeling and analytical theory, we present an effective solution of this problem based on the dipolar interaction between two laterally adjacent nanoscale spin-wave waveguides. The developed device based on this principle can work as a multifunctional and dynamically reconfigurable signal directional coupler performing the functions of a waveguide crossing element, tunable power splitter, frequency separator, or multiplexer. The proposed design of a spin-wave directional coupler can be used both in digital logic circuits intended for spin-wave computing and in analog microwave signal processing devices. PMID:29376117

Reconfigurable nanoscale spin-wave directional coupler.

PubMed

Wang, Qi; Pirro, Philipp; Verba, Roman; Slavin, Andrei; Hillebrands, Burkard; Chumak, Andrii V

2018-01-01

Spin waves, and their quanta magnons, are prospective data carriers in future signal processing systems because Gilbert damping associated with the spin-wave propagation can be made substantially lower than the Joule heat losses in electronic devices. Although individual spin-wave signal processing devices have been successfully developed, the challenging contemporary problem is the formation of two-dimensional planar integrated spin-wave circuits. Using both micromagnetic modeling and analytical theory, we present an effective solution of this problem based on the dipolar interaction between two laterally adjacent nanoscale spin-wave waveguides. The developed device based on this principle can work as a multifunctional and dynamically reconfigurable signal directional coupler performing the functions of a waveguide crossing element, tunable power splitter, frequency separator, or multiplexer. The proposed design of a spin-wave directional coupler can be used both in digital logic circuits intended for spin-wave computing and in analog microwave signal processing devices.

NMRPipe: a multidimensional spectral processing system based on UNIX pipes.

PubMed

Delaglio, F; Grzesiek, S; Vuister, G W; Zhu, G; Pfeifer, J; Bax, A

1995-11-01

The NMRPipe system is a UNIX software environment of processing, graphics, and analysis tools designed to meet current routine and research-oriented multidimensional processing requirements, and to anticipate and accommodate future demands and developments. The system is based on UNIX pipes, which allow programs running simultaneously to exchange streams of data under user control. In an NMRPipe processing scheme, a stream of spectral data flows through a pipeline of processing programs, each of which performs one component of the overall scheme, such as Fourier transformation or linear prediction. Complete multidimensional processing schemes are constructed as simple UNIX shell scripts. The processing modules themselves maintain and exploit accurate records of data sizes, detection modes, and calibration information in all dimensions, so that schemes can be constructed without the need to explicitly define or anticipate data sizes or storage details of real and imaginary channels during processing. The asynchronous pipeline scheme provides other substantial advantages, including high flexibility, favorable processing speeds, choice of both all-in-memory and disk-bound processing, easy adaptation to different data formats, simpler software development and maintenance, and the ability to distribute processing tasks on multi-CPU computers and computer networks.

System Configured For Applying Multiple Modifying Agents To A Substrate.

DOEpatents

Propp, W. Alan; Argyle, Mark D.; Janikowski, Stuart K.; Fox, Robert V.; Toth, William J.; Ginosar, Daniel M.; Allen, Charles A.; Miller, David L.

2005-11-08

The present invention is related to the modifying of substrates with multiple modifying agents in a single continuous system. At least two processing chambers are configured for modifying the substrate in a continuous feed system. The processing chambers can be substantially isolated from one another by interstitial seals. Additionally, the two processing chambers can be substantially isolated from the surrounding atmosphere by end seals. Optionally, expansion chambers can be used to separate the seals from the processing chambers.

System configured for applying multiple modifying agents to a substrate

DOEpatents

Propp, W. Alan; Argyle, Mark D.; Janikowski, Stuart K.; Fox, Robert V.; Toth, William J.; Ginosar, Daniel M.; Allen, Charles A.; Miller, David L.

2003-11-25

The present invention is related to the modifying of substrates with multiple modifying agents in a single continuous system. At least two processing chambers are configured for modifying the substrate in a continuous feed system. The processing chambers can be substantially isolated from one another by interstitial seals. Additionally, the two processing chambers can be substantially isolated from the surrounding atmosphere by end seals. Optionally, expansion chambers can be used to separate the seals from the processing chambers.

[Comparing case management care models for people with dementia and their caregivers: the design of the COMPAS study].

PubMed

van Hout, H P J; Macneil Vroomen, J L; Van Mierlo, L D; Meiland, F J M; Moll van Charante, E P; Joling, K J; van den Dungen, P; Dröes, R M; van der Horst, H E; de Rooij, S E J A

2014-04-01

Dementia care in The Netherlands is shifting from fragmented, ad hoc care to more coordinated and personalized care. Case management contributes to this shift. The linkage model and a combination of intensive case management and joint agency care models were selected based on their emerging prominence in The Netherlands. It is unclear if these different forms of case management are more effective than usual care in improving or preserving the functioning and well-being at the patient and caregiver level and at the societal cost. The objective of this article is to describe the design of a study comparing these two case management care models against usual care. Clinical and cost outcomes are investigated while care processes and the facilitators and barriers for implementation of these models are considered. Mixed methods include a prospective, observational, controlled, cohort study among persons with dementia and their primary informal caregiver in regions of The Netherlands with and without case management including a qualitative process evaluation. Community-dwelling individuals with a dementia diagnosis with an informal caregiver are included. The primary outcome measure is the Neuropsychiatric Inventory for the people with dementia and the General Health Questionnaire for their caregivers. Costs are measured from a societal perspective. Semi-structured interviews with stakeholders based on the theoretical model of adaptive implementation are planned. 521 pairs of persons with dementia and their primary informal caregiver were included and are followed over two years. In the linked model substantially more impeding factors for implementation were identified compared with the model. This article describes the design of an evaluation study of two case management models along with clinical and economic data from persons with dementia and caregivers. The impeding and facilitating factors differed substantially between the two models. Further results on cost-effectiveness are expected by the beginning of 2015. This is a Dutch adaptation of MacNeil Vroomen et al., Comparing Dutch case management care models for people with dementia and their caregivers: The design of the COMPAS study.

Manufacturing conditioned roughness and wear of biomedical oxide ceramics for all-ceramic knee implants

PubMed Central

2013-01-01

Background Ceramic materials are used in a growing proportion of hip joint prostheses due to their wear resistance and biocompatibility properties. However, ceramics have not been applied successfully in total knee joint endoprostheses to date. One reason for this is that with strict surface quality requirements, there are significant challenges with regard to machining. High-toughness bioceramics can only be machined by grinding and polishing processes. The aim of this study was to develop an automated process chain for the manufacturing of an all-ceramic knee implant. Methods A five-axis machining process was developed for all-ceramic implant components. These components were used in an investigation of the influence of surface conformity on wear behavior under simplified knee joint motion. Results The implant components showed considerably reduced wear compared to conventional material combinations. Contact area resulting from a variety of component surface shapes, with a variety of levels of surface conformity, greatly influenced wear rate. Conclusions It is possible to realize an all-ceramic knee endoprosthesis device, with a precise and affordable manufacturing process. The shape accuracy of the component surfaces, as specified by the design and achieved during the manufacturing process, has a substantial influence on the wear behavior of the prosthesis. This result, if corroborated by results with a greater sample size, is likely to influence the design parameters of such devices. PMID:23988155

Manufacturing conditioned roughness and wear of biomedical oxide ceramics for all-ceramic knee implants.

PubMed

Turger, Anke; Köhler, Jens; Denkena, Berend; Correa, Tomas A; Becher, Christoph; Hurschler, Christof

2013-08-29

Ceramic materials are used in a growing proportion of hip joint prostheses due to their wear resistance and biocompatibility properties. However, ceramics have not been applied successfully in total knee joint endoprostheses to date. One reason for this is that with strict surface quality requirements, there are significant challenges with regard to machining. High-toughness bioceramics can only be machined by grinding and polishing processes. The aim of this study was to develop an automated process chain for the manufacturing of an all-ceramic knee implant. A five-axis machining process was developed for all-ceramic implant components. These components were used in an investigation of the influence of surface conformity on wear behavior under simplified knee joint motion. The implant components showed considerably reduced wear compared to conventional material combinations. Contact area resulting from a variety of component surface shapes, with a variety of levels of surface conformity, greatly influenced wear rate. It is possible to realize an all-ceramic knee endoprosthesis device, with a precise and affordable manufacturing process. The shape accuracy of the component surfaces, as specified by the design and achieved during the manufacturing process, has a substantial influence on the wear behavior of the prosthesis. This result, if corroborated by results with a greater sample size, is likely to influence the design parameters of such devices.

31 CFR 536.408 - Alleged change in ownership or control of an entity designated as a specially designated...

Code of Federal Regulations, 2010 CFR

2010-07-01

... sale of the entity to its new owners. (b) Any continuing substantial financial obligations on the part... to or other enrichment of a specially designated narcotics trafficker could lead to designation of...

Evidence-Based and Value-Based Decision Making About Healthcare Design: An Economic Evaluation of the Safety and Quality Outcomes.

PubMed

Zadeh, Rana; Sadatsafavi, Hessam; Xue, Ryan

2015-01-01

This study describes a vision and framework that can facilitate the implementation of evidence-based design (EBD), scientific knowledge base into the process of the design, construction, and operation of healthcare facilities and clarify the related safety and quality outcomes for the stakeholders. The proposed framework pairs EBD with value-driven decision making and aims to improve communication among stakeholders by providing a common analytical language. Recent EBD research indicates that the design and operation of healthcare facilities contribute to an organization's operational success by improving safety, quality, and efficiency. However, because little information is available about the financial returns of evidence-based investments, such investments are readily eliminated during the capital-investment decision-making process. To model the proposed framework, we used engineering economy tools to evaluate the return on investments in six successful cases, identified by a literature review, in which facility design and operation interventions resulted in reductions in hospital-acquired infections, patient falls, staff injuries, and patient anxiety. In the evidence-based cases, calculated net present values, internal rates of return, and payback periods indicated that the long-term benefits of interventions substantially outweighed the intervention costs. This article explained a framework to develop a research-based and value-based communication language on specific interventions along the planning, design and construction, operation, and evaluation stages. Evidence-based and value-based design frameworks can be applied to communicate the life-cycle costs and savings of EBD interventions to stakeholders, thereby contributing to more informed decision makings and the optimization of healthcare infrastructures. © The Author(s) 2015.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, Dean J.; Harding, Lee T.

Isotope identification algorithms that are contained in the Gamma Detector Response and Analysis Software (GADRAS) can be used for real-time stationary measurement and search applications on platforms operating under Linux or Android operating sys-tems. Since the background radiation can vary considerably due to variations in natu-rally-occurring radioactive materials (NORM), spectral algorithms can be substantial-ly more sensitive to threat materials than search algorithms based strictly on count rate. Specific isotopes or interest can be designated for the search algorithm, which permits suppression of alarms for non-threatening sources, such as such as medical radionuclides. The same isotope identification algorithms that are usedmore » for search ap-plications can also be used to process static measurements. The isotope identification algorithms follow the same protocols as those used by the Windows version of GADRAS, so files that are created under the Windows interface can be copied direct-ly to processors on fielded sensors. The analysis algorithms contain provisions for gain adjustment and energy lineariza-tion, which enables direct processing of spectra as they are recorded by multichannel analyzers. Gain compensation is performed by utilizing photopeaks in background spectra. Incorporation of this energy calibration tasks into the analysis algorithm also eliminates one of the more difficult challenges associated with development of radia-tion detection equipment.« less

External Tank Program - Legacy of Success

NASA Technical Reports Server (NTRS)

Pilet, Jeffery C.; Diecidue-Conners, Dawn; Worden, Michelle; Guillot, Michelle; Welzyn, Kenneth

2011-01-01

The largest single element of Space Shuttle is the External Tank (ET), which serves as the structural backbone of the vehicle during ascent and provides liquid propellants to the Orbiter s three Main Engines. The ET absorbs most of the seven million pounds of thrust exerted by the Solid Rocket Boosters and Main Engines. The design evolved through several block changes, reducing weight each time. Because the tank flies to orbital velocity with the Space Shuttle Orbiter, minimization of weight is mandatory, to maximize payload performance. The initial configuration, the standard weight tank, weighed 76,000 pounds and was an aluminum 2219 structure. The light weight tank weighed 66,000 pounds and flew 86 missions. The super light weight tank weighed 58,500 pounds and was primarily an aluminum-lithium structure. The final configuration and low weight enabled system level performance sufficient for assembly of the International Space Station in a high inclination orbit, vital for international cooperation. Another significant challenge was the minimization of ice formation on the cryogenic tanks. This was essential due to the system configuration and the choice of ceramic thermal protection system materials on the Orbiter. Ice would have been a major debris hazard. Spray on foam insulation materials served multiple functions including thermal insulation, conditioning of cryogenic propellants, and thermal protection for the tank structure during ascent and entry. The tank is large, and unique manufacturing facilities, tooling, and handling, and transportation operations were developed. Weld processes and tooling evolved with the design as it matured through several block changes. Non Destructive Evaluation methods were used to assure integrity of welds and thermal protection system materials. The aluminum-lithium alloy was used near the end of the program and weld processes and weld repair techniques had to be refined. Development and implementation of friction stir welding was a substantial technology development incorporated during the Program. Automated thermal protection system application processes were developed for the majority of the tank surface. Material obsolescence was an issue throughout the multi-decade program. Process controls were implemented to assure cleanliness in the production environment, to control contaminants, and to preclude corrosion. Each tank was accepted via rigorous inspections, including non-destructive evaluation techniques, proof testing, and all systems testing. In the post STS-107 era, the project focused on ascent debris risk reduction. This was accomplished via stringent process controls, post flight assessment using substantially improved imagery, and selective redesigns. These efforts were supported with a number of test programs to simulate combined environments. The debris risk was reduced by two orders of magnitude. During this time a major natural disaster was overcome when hurricane Katrina damaged the manufacturing facility. Numerous lessons from these efforts, the manufacturing and material processing issues, the key design features, and evolution of the design will be discussed.

Development of an Ecological Momentary Assessment Mobile App for a Low-Literacy, Mexican American Population to Collect Disordered Eating Behaviors

PubMed Central

Stein, Karen F; Chaudry, Beenish; Trabold, Nicole

2016-01-01

Background Ecological momentary assessment (EMA) is a popular method for understanding population health in which participants report their experiences while in naturally occurring contexts in order to increase the reliability and ecological validity of the collected data (as compared to retrospective recall). EMA studies, however, have relied primarily on text-based questionnaires, effectively eliminating low-literacy populations from the samples. Objective To provide a case study of design of an EMA mobile app for a low-literacy population. In particular, we present the design process and final design of an EMA mobile app for low literate, Mexican American women to record unhealthy eating and weight control behaviors (UEWCBs). Methods An iterative, user-centered design process was employed to develop the mobile app. An existing EMA protocol to measure UEWCBs in college-enrolled Mexican American women was used as the starting point for the application. The app utilizes an icon interface, with optional audio prompts, that is culturally sensitive and usable by a low-literacy population. A total of 41 women participated over the course of 4 phases of the design process, which included 2 interview and task-based phases (n=8, n=11), focus groups (n=15), and a 5-day, in situ deployment (n=7). Results Participants’ mental models of UEWCBs differed substantially from prevailing definitions found in the literature, prompting a major reorganization of the app interface. Differences in health literacy and numeracy were better identified with the Newest Vital Sign tool, as compared with the Short Assessment of Health Literacy tool. Participants had difficulty imagining scenarios in the interviews to practice recording a specific UEWCB; instead, usability was best tested in situ. Participants were able to use the EMA mobile app over the course of 5 days to record UEWCBs. Conclusions Results suggest that the iterative, user-centered design process was essential for designing the app to be made usable by the target population. Simply taking the protocol designed for a higher-literacy population and replacing words with icons and/or audio would have been unsuccessful with this population. PMID:27418020

The broader cognitive phenotype of autism in parents: how specific is the tendency for local processing and executive dysfunction?

PubMed

Bölte, Sven; Poustka, Fritz

2006-06-01

The objective of this study was to investigate the tendency for local processing style ('weak central coherence') and executive dysfunction in parents of subjects with an autism spectrum disorder (ASD) compared with parents of individuals with early onset schizophrenia (EOS) and mental retardation (MR). Sixty-two parents of subjects with ASD, 36 parents of subjects with EOS and 30 parents of subjects with MR were examined. Data on two scales indicative of local visual processing (Embedded Figures Test, Block Design) and on three executive function tests (Wisconsin Card Sorting Test, Tower of Hanoi, Trailmaking Test) were collected for all participants. Parents of subjects with ASD performed significantly faster on the Embedded Figures Test compared with both control samples. No other substantial group differences were observed. The findings indicate that an increased tendency for local processing in terms of visual disembedding could be a relatively specific core feature of the broader cognitive phenotype of autism in parents.

Empiric validation of a process for behavior change.

PubMed

Elliot, Diane L; Goldberg, Linn; MacKinnon, David P; Ranby, Krista W; Kuehl, Kerry S; Moe, Esther L

2016-09-01

Most behavior change trials focus on outcomes rather than deconstructing how those outcomes related to programmatic theoretical underpinnings and intervention components. In this report, the process of change is compared for three evidence-based programs' that shared theories, intervention elements and potential mediating variables. Each investigation was a randomized trial that assessed pre- and post- intervention variables using survey constructs with established reliability. Each also used mediation analyses to define relationships. The findings were combined using a pattern matching approach. Surprisingly, knowledge was a significant mediator in each program (a and b path effects [p<0.01]). Norms, perceived control abilities, and self-monitoring were confirmed in at least two studies (p<0.01 for each). Replication of findings across studies with a common design but varied populations provides a robust validation of the theory and processes of an effective intervention. Combined findings also demonstrate a means to substantiate process aspects and theoretical models to advance understanding of behavior change.

H-Coal process and plant design

DOEpatents

Kydd, Paul H.; Chervenak, Michael C.; DeVaux, George R.

1983-01-01

A process for converting coal and other hydrocarbonaceous materials into useful and more valuable liquid products. The process comprises: feeding coal and/or other hydrocarbonaceous materials with a hydrogen-containing gas into an ebullated catalyst bed reactor; passing the reaction products from the reactor to a hot separator where the vaporous and distillate products are separated from the residuals; introducing the vaporous and distillate products from the separator directly into a hydrotreater where they are further hydrogenated; passing the residuals from the separator successively through flash vessels at reduced pressures where distillates are flashed off and combined with the vaporous and distillate products to be hydrogenated; transferring the unseparated residuals to a solids concentrating and removal means to remove a substantial portion of solids therefrom and recycling the remaining residual oil to the reactor; and passing the hydrogenated vaporous and distillate products to an atmospheric fractionator where the combined products are fractionated into separate valuable liquid products. The hydrogen-containing gas is generated from sources within the process.

Transonic airfoil design for helicopter rotor applications

NASA Technical Reports Server (NTRS)

Hassan, Ahmed A.; Jackson, B.

1989-01-01

Despite the fact that the flow over a rotor blade is strongly influenced by locally three-dimensional and unsteady effects, practical experience has always demonstrated that substantial improvements in the aerodynamic performance can be gained by improving the steady two-dimensional charateristics of the airfoil(s) employed. The two phenomena known to have great impact on the overall rotor performance are: (1) retreating blade stall with the associated large pressure drag, and (2) compressibility effects on the advancing blade leading to shock formation and the associated wave drag and boundary-layer separation losses. It was concluded that: optimization routines are a powerful tool for finding solutions to multiple design point problems; the optimization process must be guided by the judicious choice of geometric and aerodynamic constraints; optimization routines should be appropriately coupled to viscous, not inviscid, transonic flow solvers; hybrid design procedures in conjunction with optimization routines represent the most efficient approach for rotor airfroil design; unsteady effects resulting in the delay of lift and moment stall should be modeled using simple empirical relations; and inflight optimization of aerodynamic loads (e.g., use of variable rate blowing, flaps, etc.) can satisfy any number of requirements at design and off-design conditions.

An adaptive optics imaging system designed for clinical use.

PubMed

Zhang, Jie; Yang, Qiang; Saito, Kenichi; Nozato, Koji; Williams, David R; Rossi, Ethan A

2015-06-01

Here we demonstrate a new imaging system that addresses several major problems limiting the clinical utility of conventional adaptive optics scanning light ophthalmoscopy (AOSLO), including its small field of view (FOV), reliance on patient fixation for targeting imaging, and substantial post-processing time. We previously showed an efficient image based eye tracking method for real-time optical stabilization and image registration in AOSLO. However, in patients with poor fixation, eye motion causes the FOV to drift substantially, causing this approach to fail. We solve that problem here by tracking eye motion at multiple spatial scales simultaneously by optically and electronically integrating a wide FOV SLO (WFSLO) with an AOSLO. This multi-scale approach, implemented with fast tip/tilt mirrors, has a large stabilization range of ± 5.6°. Our method consists of three stages implemented in parallel: 1) coarse optical stabilization driven by a WFSLO image, 2) fine optical stabilization driven by an AOSLO image, and 3) sub-pixel digital registration of the AOSLO image. We evaluated system performance in normal eyes and diseased eyes with poor fixation. Residual image motion with incremental compensation after each stage was: 1) ~2-3 arc minutes, (arcmin) 2) ~0.5-0.8 arcmin and, 3) ~0.05-0.07 arcmin, for normal eyes. Performance in eyes with poor fixation was: 1) ~3-5 arcmin, 2) ~0.7-1.1 arcmin and 3) ~0.07-0.14 arcmin. We demonstrate that this system is capable of reducing image motion by a factor of ~400, on average. This new optical design provides additional benefits for clinical imaging, including a steering subsystem for AOSLO that can be guided by the WFSLO to target specific regions of interest such as retinal pathology and real-time averaging of registered images to eliminate image post-processing.

Cleanliness of Ti-bearing Al-killed ultra-low-carbon steel during different heating processes

NASA Astrophysics Data System (ADS)

Guo, Jian-long; Bao, Yan-ping; Wang, Min

2017-12-01

During the production of Ti-bearing Al-killed ultra-low-carbon (ULC) steel, two different heating processes were used when the converter tapping temperature or the molten steel temperature in the Ruhrstahl-Heraeus (RH) process was low: heating by Al addition during the RH decarburization process and final deoxidation at the end of the RH decarburization process (process-I), and increasing the oxygen content at the end of RH decarburization, heating and final deoxidation by one-time Al addition (process-II). Temperature increases of 10°C by different processes were studied; the results showed that the two heating processes could achieve the same heating effect. The T.[O] content in the slab and the refining process was better controlled by process-I than by process-II. Statistical analysis of inclusions showed that the numbers of inclusions in the slab obtained by process-I were substantially less than those in the slab obtained by process-II. For process-I, the Al2O3 inclusions produced by Al added to induce heating were substantially removed at the end of decarburization. The amounts of inclusions were substantially greater for process-II than for process-I at different refining stages because of the higher dissolved oxygen concentration in process-II. Industrial test results showed that process-I was more beneficial for improving the cleanliness of molten steel.

The jet engine design that can drastically reduce oxides of nitrogen

NASA Technical Reports Server (NTRS)

Ferri, A.; Agnone, A.

1977-01-01

The NOx pollution problem of hydrogen fueled turbojets and supersonic combustion ramjets (scramjets) was investigated to determine means of substantially alleviating the problem. Since the NOx reaction rates are much slower than the energy producing reactions, the NOx production depends mainly on the maximum local temperatures in the combustor and the NOx concentration is far from equilibrium at the end of a typical combustor (L approximately 1 ft). In diffusion flames, as used in present turbojets and scramjets combustor designs, the maximum local temperature occurs at the flame and is equal to the stoichiometric value. Whereas, in the heat conduction flames, wherein the flame propagates due to a heat conduction process away from the flame to the cooler oncoming premixed unburnt gases, the maximum temperature is lower than in the diffusion flame. Hence the corresponding pollution index is also lower.

Experimental design and statistical methods for improved hit detection in high-throughput screening.

PubMed

Malo, Nathalie; Hanley, James A; Carlile, Graeme; Liu, Jing; Pelletier, Jerry; Thomas, David; Nadon, Robert

2010-09-01

Identification of active compounds in high-throughput screening (HTS) contexts can be substantially improved by applying classical experimental design and statistical inference principles to all phases of HTS studies. The authors present both experimental and simulated data to illustrate how true-positive rates can be maximized without increasing false-positive rates by the following analytical process. First, the use of robust data preprocessing methods reduces unwanted variation by removing row, column, and plate biases. Second, replicate measurements allow estimation of the magnitude of the remaining random error and the use of formal statistical models to benchmark putative hits relative to what is expected by chance. Receiver Operating Characteristic (ROC) analyses revealed superior power for data preprocessed by a trimmed-mean polish method combined with the RVM t-test, particularly for small- to moderate-sized biological hits.

Attrition in the kimberlite system

NASA Astrophysics Data System (ADS)

Jones, Thomas J.; Russell, James K.

2018-05-01

The sustained transportation of particles in a suspension commonly results in particle attrition leading to grain size reduction and shape modification. Particle attrition is a well-studied phenomenon that has mainly focussed on sediments produced in aeolian or fluvial environments. Here, we present analogue experiments designed to explore processes of attrition in the kimberlite system; we focus on olivine as it is the most abundant constituent of kimberlite. The attrition experiments on olivine use separate experimental set-ups to approximate two natural environments relevant to kimberlites. Tumbling mill experiments feature a low energy system supporting near continual particle-particle contact and are relevant to re-sedimentation and dispersal processes. Experiments performed in a fluidized particle bed constitute a substantially higher energy environment pertinent to kimberlite ascent and eruption. The run-products of each experiment are analysed for grain size reduction and shape modification and these data are used to elucidate the rates and extents of olivine attrition as a function of time and energy. Lastly, we model the two experimental datasets with an empirical rate equation that describes the production of daughter products (fines) with time. Both datasets approach a fines production limit, or plateau, at long particle residence times; the fluidized system is much more efficient producing a substantially higher fines content and reaches the plateau faster. Our experimental results and models provide a way to forensically examine a wide range of processes relevant to kimberlite on the basis of olivine size and shape properties.

Two-stage coal liquefaction process

DOEpatents

Skinner, Ronald W.; Tao, John C.; Znaimer, Samuel

1985-01-01

An improved SRC-I two-stage coal liquefaction process which improves the product slate is provided. Substantially all of the net yield of 650.degree.-850.degree. F. heavy distillate from the LC-Finer is combined with the SRC process solvent, substantially all of the net 400.degree.-650.degree. F. middle distillate from the SRC section is combined with the hydrocracker solvent in the LC-Finer, and the initial boiling point of the SRC process solvent is increased sufficiently high to produce a net yield of 650.degree.-850.degree. F. heavy distillate of zero for the two-stage liquefaction process.

Critical care nurses management of prolonged weaning: an interview study.

PubMed

Cederwall, Carl-Johan; Plos, Kaety; Rose, Louise; Dübeck, Amanda; Ringdal, Mona

2014-09-01

For most critically ill patients requiring mechanical ventilation in the intensive care unit (ICU) weaning is uncomplicated. For the remainder, weaning is a challenge and may result in further complications and increased risk of mortality. Critical care nurses (CCNs) require substantial knowledge and experience to manage patients experiencing prolonged weaning. The aim of this study was to explore CCNs approach for management of patients experiencing prolonged weaning in the ICU. A descriptive qualitative design. Semi-structured interviews with 19 experienced CCNs were conducted. Data were analysed using content analysis. Participants used various strategies for weaning that were grouped into four categories: individualized planning for the weaning process, assessing patient's capacity, managing the process and team interaction. The overall theme that emerged was: CCNs drive the weaning process using both a patient centred and targeted approach. CCNs in these ICUs performed weaning using a patient centred approach to plan, initiate, assess and establish a holistic weaning process. Team collaboration among all health care practitioners was important. CCNs have a key role in prioritizing weaning and driving the process forward. Closeness to the patient and a key role in management of the mechanical ventilated patient in ICU gives the CCN unique potential to develop and create models and tools for prolonged weaning. These tools, specially designed for patients undergoing prolonged weaning, would give focus on continuous planning, collaborating, managing and evaluation in the process of liberating patients from mechanical ventilation. © 2014 British Association of Critical Care Nurses.

Traffic and data preparation for AASHTO MEPDG analysis and designs.

DOT National Transportation Integrated Search

2011-10-01

"The Mechanistic Empirical Pavement Design Guide (MEPDG) and the : subsequent AASHTO product DARWin-ME are signifi cant advancements in : pavement design. However, they are substantially more complex than the : 1993 AASHTO Guide, which is currently u...

Acoustic noise and functional magnetic resonance imaging: current strategies and future prospects.

PubMed

Amaro, Edson; Williams, Steve C R; Shergill, Sukhi S; Fu, Cynthia H Y; MacSweeney, Mairead; Picchioni, Marco M; Brammer, Michael J; McGuire, Philip K

2002-11-01

Functional magnetic resonance imaging (fMRI) has become the method of choice for studying the neural correlates of cognitive tasks. Nevertheless, the scanner produces acoustic noise during the image acquisition process, which is a problem in the study of auditory pathway and language generally. The scanner acoustic noise not only produces activation in brain regions involved in auditory processing, but also interferes with the stimulus presentation. Several strategies can be used to address this problem, including modifications of hardware and software. Although reduction of the source of the acoustic noise would be ideal, substantial hardware modifications to the current base of installed MRI systems would be required. Therefore, the most common strategy employed to minimize the problem involves software modifications. In this work we consider three main types of acquisitions: compressed, partially silent, and silent. For each implementation, paradigms using block and event-related designs are assessed. We also provide new data, using a silent event-related (SER) design, which demonstrate higher blood oxygen level-dependent (BOLD) response to a simple auditory cue when compared to a conventional image acquisition. Copyright 2002 Wiley-Liss, Inc.

From development to implementation-A smartphone and email-based discharge follow-up program for pediatric patients after hospital discharge.

PubMed

Hopkins, Israel Green; Dunn, Kelly; Bourgeois, Fabienne; Rogers, Jayne; Chiang, Vincent W

2016-06-01

The purpose of this case study was to investigate opportunities to electronically enhance the transitions of care for both patients and providers and to describe the process of development and implementation of such tools. We describe the current challenges and fragmentation of care for pediatric patients and families being discharged from inpatient stays, and review barriers to change in practice. Care transitions vary in the complexity of the clinical and social scenarios and no one-size-fits-all approach works for every patient, provider or hospital system. A substantial challenge that providers who are designing and implementing digital tools for patients surrounds the complexity in building such tools to apply to such broad populations. Our case study provides a framework using a multidisciplinary approach, brainstorming and rapid digital prototyping to build an in-house electronic discharge follow-up platform. In describing this process, we review design and implementation measures that may further support digital tool development in other areas. Copyright © 2015 Elsevier Inc. All rights reserved.

In situ fatigue loading stage inside scanning electron microscope

NASA Technical Reports Server (NTRS)

Telesman, Jack; Kantzos, Peter; Brewer, David

1988-01-01

A fatigue loading stage inside a scanning electron microscopy (SEM) was developed. The stage allows dynamic and static high-magnification and high-resolution viewing of the fatigue crack initiation and crack propagation processes. The loading stage is controlled by a closed-loop servohydraulic system. Maximum load is 1000 lb (4450 N) with test frequencies ranging up to 30 Hz. The stage accommodates specimens up to 2 inches (50 mm) in length and tolerates substantial specimen translation to view the propagating crack. At room temperature, acceptable working resolution is obtainable for magnifications ranging up to 10,000X. The system is equipped with a high-temperature setup designed for temperatures up to 2000 F (1100 C). The signal can be videotaped for further analysis of the pertinent fatigue damage mechanisms. The design allows for quick and easy interchange and conversion of the SEM from a loading stage configuration to its normal operational configuration and vice versa. Tests are performed entirely in the in-situ mode. In contrast to other designs, the NASA design has greatly extended the life of the loading stage by not exposing the bellows to cyclic loading. The loading stage was used to investigate the fatigue crack growth mechanisms in the (100)-oriented PWA 1480 single-crystal, nickel-based supperalloy. The high-magnification observations revealed the details of the crack growth processes.

Future supply chains enabled by continuous processing--opportunities and challenges. May 20-21, 2014 Continuous Manufacturing Symposium.

PubMed

Srai, Jagjit Singh; Badman, Clive; Krumme, Markus; Futran, Mauricio; Johnston, Craig

2015-03-01

This paper examines the opportunities and challenges facing the pharmaceutical industry in moving to a primarily "continuous processing"-based supply chain. The current predominantly "large batch" and centralized manufacturing system designed for the "blockbuster" drug has driven a slow-paced, inventory heavy operating model that is increasingly regarded as inflexible and unsustainable. Indeed, new markets and the rapidly evolving technology landscape will drive more product variety, shorter product life-cycles, and smaller drug volumes, which will exacerbate an already unsustainable economic model. Future supply chains will be required to enhance affordability and availability for patients and healthcare providers alike despite the increased product complexity. In this more challenging supply scenario, we examine the potential for a more pull driven, near real-time demand-based supply chain, utilizing continuous processing where appropriate as a key element of a more "flow-through" operating model. In this discussion paper on future supply chain models underpinned by developments in the continuous manufacture of pharmaceuticals, we have set out; The significant opportunities to moving to a supply chain flow-through operating model, with substantial opportunities in inventory reduction, lead-time to patient, and radically different product assurance/stability regimes. Scenarios for decentralized production models producing a greater variety of products with enhanced volume flexibility. Production, supply, and value chain footprints that are radically different from today's monolithic and centralized batch manufacturing operations. Clinical trial and drug product development cost savings that support more rapid scale-up and market entry models with early involvement of SC designers within New Product Development. The major supply chain and industrial transformational challenges that need to be addressed. The paper recognizes that although current batch operational performance in pharma is far from optimal and not necessarily an appropriate end-state benchmark for batch technology, the adoption of continuous supply chain operating models underpinned by continuous production processing, as full or hybrid solutions in selected product supply chains, can support industry transformations to deliver right-first-time quality at substantially lower inventory profiles. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

An evaluation of different setups for simulating lighting characteristics

NASA Astrophysics Data System (ADS)

Salters, Bart; Murdoch, Michael; Sekulovksi, Dragan; Chen, Shih-Han; Seuntiens, Pieter

2012-03-01

The advance of technology continuously enables new luminaire designs and concepts. Evaluating such designs has traditionally been done using actual prototypes, in a real environment. The iterations needed to build, verify, and improve luminaire designs incur substantial costs and slow down the design process. A more attractive way is to evaluate designs using simulations, as they can be made cheaper and quicker for a wider variety of prototypes. However, the value of such simulations is determined by how closely they predict the outcome of actual perception experiments. In this paper, we discuss an actual perception experiment including several lighting settings in a normal office environment. The same office environment also has been modeled using different software tools, and photo-realistic renderings have been created of these models. These renderings were subsequently processed using various tonemapping operators in preparation for display. The total imaging chain can be considered a simulation setup, and we have executed several perception experiments on different setups. Our real interest is in finding which imaging chain gives us the best result, or in other words, which of them yields the closest match between virtual and real experiment. To answer this question, first of all an answer has to be found to the question, "which simulation setup matches the real world best?" As there is no unique, widely accepted measure to describe the performance of a certain setup, we consider a number of options and discuss the reasoning behind them along with their advantages and disadvantages.

Comminution process to produce wood particles of uniform size and shape with disrupted grain structure from veneer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dooley, James H.; Lanning, David N.

Comminution process of wood veneer to produce wood particles, by feeding wood veneer in a direction of travel substantially normal to grain through a counter rotating pair of intermeshing arrays of cutting discs arrayed axially perpendicular to the direction of wood veneer travel, wherein the cutting discs have a uniform thickness (Td), to produce wood particles characterized by a length dimension (L) substantially equal to the Td and aligned substantially parallel to grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) aligned normal to W and L, wherein the W.times.H dimensions definemore » a pair of substantially parallel end surfaces with end checking between crosscut fibers.« less

External Tank - The Structure Backbone

NASA Technical Reports Server (NTRS)

Welzyn, Kenneth; Pilet, Jeffrey C.; Diecidue-Conners, Dawn; Worden, Michelle; Guillot, Michelle

2011-01-01

The External Tank forms the structural backbone of the Space Shuttle in the launch configuration. Because the tank flies to orbital velocity with the Space Shuttle Orbiter, minimization of weight is mandatory, to maximize payload performance. Choice of lightweight materials both for structure and thermal conditioning was necessary. The tank is large, and unique manufacturing facilities, tooling, handling, and transportation operations were required. Weld processes and tooling evolved with the design as it matured through several block changes, to reduce weight. Non Destructive Evaluation methods were used to assure integrity of welds and thermal protection system materials. The aluminum-lithium alloy was used near the end of the program and weld processes and weld repair techniques had to be refined. Development and implementation of friction stir welding was a substantial technology development incorporated during the Program. Automated thermal protection system application processes were developed for the majority of the tank surface. Material obsolescence was an issue throughout the 40 year program. The final configuration and tank weight enabled international space station assembly in a high inclination orbit allowing international cooperation with the Russian Federal Space Agency. Numerous process controls were implemented to assure product quality, and innovative proof testing was accomplished prior to delivery. Process controls were implemented to assure cleanliness in the production environment, to control contaminants, and to preclude corrosion. Each tank was accepted via rigorous inspections, including non-destructive evaluation techniques, proof testing, and all systems testing. In the post STS-107 era, the project focused on ascent debris risk reduction. This was accomplished via stringent process controls, post flight assessment using substantially improved imagery, and selective redesigns. These efforts were supported with a number of test programs to simulate combined environments. Processing improvements included development and use of low spray guns for foam application, additional human factors considerations for production, use of high fidelity mockups during hardware processing with video review, improved tank access, extensive use of non destructive evaluation, and producibility enhancements. Design improvements included redesigned bipod fittings, a bellows heater, a feedline camera active during ascent flight, removal of the protuberance airload ramps, redesigned ice frost ramps, and titanium brackets replaced aluminum brackets on the liquid oxygen feedline. Post flight assessment improved due to significant addition of imagery assets, greatly improving situational awareness. The debris risk was reduced by two orders of magnitude. During this time a major natural disaster was overcome when Katrina damaged the manufacturing facility. Numerous lessons from these efforts are documented within the paper.

Rational design of efficient electrode–electrolyte interfaces for solid-state energy storage using ion soft landing

DOE PAGES

Prabhakaran, Venkateshkumar; Mehdi, B. Layla; Ditto, Jeffrey J.; ...

2016-04-21

Here, the rational design of improved electrode-electrolyte interfaces (EEI) for energy storage is critically dependent on a molecular-level understanding of ionic interactions and nanoscale phenomena. The presence of non-redox active species at EEI has been shown to strongly influence Faradaic efficiency and long-term operational stability during energy storage processes. Herein, we achieve substantially higher performance and long-term stability of EEI prepared with highly-dispersed discrete redox-active cluster anions (50 ng of pure ~0.7 nm size molybdenum polyoxometalate anions (POM) anions on 25 mg (≈ 0.2 wt%) carbon nanotube (CNT) electrodes) by complete elimination of strongly coordinating non-redox species through ion soft-landingmore » (SL). For the first time, electron microscopy provides atomically-resolved images of individual POM species directly on complex technologically relevant CNT electrodes. In this context, SL is established as a versatile approach for the controlled design of novel surfaces for both fundamental and applied research in energy storage.« less

Design and construction of a multiwavelength, micromirror total internal reflectance fluorescence microscope.

PubMed

Larson, Joshua; Kirk, Matt; Drier, Eric A; O'Brien, William; MacKay, James F; Friedman, Larry J; Hoskins, Aaron A

2014-10-01

Colocalization single-molecule spectroscopy (CoSMoS) has proven to be a useful method for studying the composition, kinetics and mechanisms of complex cellular machines. Key to the technique is the ability to simultaneously monitor multiple proteins and/or nucleic acids as they interact with one another. Here we describe a protocol for constructing a CoSMoS micromirror total internal reflection fluorescence microscope (mmTIRFM). Design and construction of a scientific microscope often requires a number of custom components and a substantial time commitment. In our protocol, we have streamlined this process by implementation of a commercially available microscopy platform designed to accommodate the optical components necessary for an mmTIRFM. The mmTIRF system eliminates the need for machining custom parts by the end user and facilitates optical alignment. Depending on the experience level of the microscope builder, these time savings and the following protocol can enable mmTIRF construction to be completed within 2 months.

Diffusion bonded boron/aluminum spar-shell fan blade

NASA Technical Reports Server (NTRS)

Carlson, C. E. K.; Cutler, J. L.; Fisher, W. J.; Memmott, J. V. W.

1980-01-01

Design and process development tasks intended to demonstrate composite blade application in large high by-pass ratio turbofan engines are described. Studies on a 3.0 aspect radio space and shell construction fan blade indicate a potential weight savings for a first stage fan rotor of 39% when a hollow titanium spar is employed. An alternate design which featured substantial blade internal volume filled with titanium honeycomb inserts achieved a 14% potential weight savings over the B/M rotor system. This second configuration requires a smaller development effort and entails less risk to translate a design into a successful product. The feasibility of metal joining large subsonic spar and shell fan blades was demonstrated. Initial aluminum alloy screening indicates a distinct preference for AA6061 aluminum alloy for use as a joint material. The simulated airfoil pressings established the necessity of rigid air surfaces when joining materials of different compressive rigidities. The two aluminum alloy matrix choices both were successfully formed into blade shells.

BactoGeNIE: A large-scale comparative genome visualization for big displays

DOE PAGES

Aurisano, Jillian; Reda, Khairi; Johnson, Andrew; ...

2015-08-13

The volume of complete bacterial genome sequence data available to comparative genomics researchers is rapidly increasing. However, visualizations in comparative genomics--which aim to enable analysis tasks across collections of genomes--suffer from visual scalability issues. While large, multi-tiled and high-resolution displays have the potential to address scalability issues, new approaches are needed to take advantage of such environments, in order to enable the effective visual analysis of large genomics datasets. In this paper, we present Bacterial Gene Neighborhood Investigation Environment, or BactoGeNIE, a novel and visually scalable design for comparative gene neighborhood analysis on large display environments. We evaluate BactoGeNIE throughmore » a case study on close to 700 draft Escherichia coli genomes, and present lessons learned from our design process. In conclusion, BactoGeNIE accommodates comparative tasks over substantially larger collections of neighborhoods than existing tools and explicitly addresses visual scalability. Given current trends in data generation, scalable designs of this type may inform visualization design for large-scale comparative research problems in genomics.« less

BactoGeNIE: a large-scale comparative genome visualization for big displays

PubMed Central

2015-01-01

Background The volume of complete bacterial genome sequence data available to comparative genomics researchers is rapidly increasing. However, visualizations in comparative genomics--which aim to enable analysis tasks across collections of genomes--suffer from visual scalability issues. While large, multi-tiled and high-resolution displays have the potential to address scalability issues, new approaches are needed to take advantage of such environments, in order to enable the effective visual analysis of large genomics datasets. Results In this paper, we present Bacterial Gene Neighborhood Investigation Environment, or BactoGeNIE, a novel and visually scalable design for comparative gene neighborhood analysis on large display environments. We evaluate BactoGeNIE through a case study on close to 700 draft Escherichia coli genomes, and present lessons learned from our design process. Conclusions BactoGeNIE accommodates comparative tasks over substantially larger collections of neighborhoods than existing tools and explicitly addresses visual scalability. Given current trends in data generation, scalable designs of this type may inform visualization design for large-scale comparative research problems in genomics. PMID:26329021

BactoGeNIE: A large-scale comparative genome visualization for big displays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aurisano, Jillian; Reda, Khairi; Johnson, Andrew

The volume of complete bacterial genome sequence data available to comparative genomics researchers is rapidly increasing. However, visualizations in comparative genomics--which aim to enable analysis tasks across collections of genomes--suffer from visual scalability issues. While large, multi-tiled and high-resolution displays have the potential to address scalability issues, new approaches are needed to take advantage of such environments, in order to enable the effective visual analysis of large genomics datasets. In this paper, we present Bacterial Gene Neighborhood Investigation Environment, or BactoGeNIE, a novel and visually scalable design for comparative gene neighborhood analysis on large display environments. We evaluate BactoGeNIE throughmore » a case study on close to 700 draft Escherichia coli genomes, and present lessons learned from our design process. In conclusion, BactoGeNIE accommodates comparative tasks over substantially larger collections of neighborhoods than existing tools and explicitly addresses visual scalability. Given current trends in data generation, scalable designs of this type may inform visualization design for large-scale comparative research problems in genomics.« less

Bayesian Optimal Interval Design: A Simple and Well-Performing Design for Phase I Oncology Trials

PubMed Central

Yuan, Ying; Hess, Kenneth R.; Hilsenbeck, Susan G.; Gilbert, Mark R.

2016-01-01

Despite more than two decades of publications that offer more innovative model-based designs, the classical 3+3 design remains the most dominant phase I trial design in practice. In this article, we introduce a new trial design, the Bayesian optimal interval (BOIN) design. The BOIN design is easy to implement in a way similar to the 3+3 design, but is more flexible for choosing the target toxicity rate and cohort size and yields a substantially better performance that is comparable to that of more complex model-based designs. The BOIN design contains the 3+3 design and the accelerated titration design as special cases, thus linking it to established phase I approaches. A numerical study shows that the BOIN design generally outperforms the 3+3 design and the modified toxicity probability interval (mTPI) design. The BOIN design is more likely than the 3+3 design to correctly select the maximum tolerated dose (MTD) and allocate more patients to the MTD. Compared to the mTPI design, the BOIN design has a substantially lower risk of overdosing patients and generally a higher probability of correctly selecting the MTD. User-friendly software is freely available to facilitate the application of the BOIN design. PMID:27407096

19 CFR 134.1 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... added to an article in another country must effect a substantial transformation in order to render such... subjects the imported article to a process which results in a substantial transformation of the article...

45 CFR 150.207 - Procedure for determining that a State fails to substantially enforce PHS Act requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 45 Public Welfare 1 2013-10-01 2013-10-01 false Procedure for determining that a State fails to... INSURANCE MARKETS CMS Enforcement Processes for Determining Whether States Are Failing To Substantially Enforce PHS Act Requirement § 150.207 Procedure for determining that a State fails to substantially...

45 CFR 150.207 - Procedure for determining that a State fails to substantially enforce HIPAA requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 45 Public Welfare 1 2010-10-01 2010-10-01 false Procedure for determining that a State fails to... MARKETS CMS Enforcement Processes for Determining Whether States Are Failing To Substantially Enforce HIPAA Requirements § 150.207 Procedure for determining that a State fails to substantially enforce HIPAA...

45 CFR 150.207 - Procedure for determining that a State fails to substantially enforce PHS Act requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 45 Public Welfare 1 2014-10-01 2014-10-01 false Procedure for determining that a State fails to... INSURANCE MARKETS CMS Enforcement Processes for Determining Whether States Are Failing To Substantially Enforce PHS Act Requirement § 150.207 Procedure for determining that a State fails to substantially...

45 CFR 150.207 - Procedure for determining that a State fails to substantially enforce HIPAA requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 45 Public Welfare 1 2011-10-01 2011-10-01 false Procedure for determining that a State fails to... MARKETS CMS Enforcement Processes for Determining Whether States Are Failing To Substantially Enforce HIPAA Requirements § 150.207 Procedure for determining that a State fails to substantially enforce HIPAA...

45 CFR 150.207 - Procedure for determining that a State fails to substantially enforce HIPAA requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 45 Public Welfare 1 2012-10-01 2012-10-01 false Procedure for determining that a State fails to... MARKETS CMS Enforcement Processes for Determining Whether States Are Failing To Substantially Enforce HIPAA Requirements § 150.207 Procedure for determining that a State fails to substantially enforce HIPAA...

Design and optimization of reverse-transcription quantitative PCR experiments.

PubMed

Tichopad, Ales; Kitchen, Rob; Riedmaier, Irmgard; Becker, Christiane; Ståhlberg, Anders; Kubista, Mikael

2009-10-01

Quantitative PCR (qPCR) is a valuable technique for accurately and reliably profiling and quantifying gene expression. Typically, samples obtained from the organism of study have to be processed via several preparative steps before qPCR. We estimated the errors of sample withdrawal and extraction, reverse transcription (RT), and qPCR that are introduced into measurements of mRNA concentrations. We performed hierarchically arranged experiments with 3 animals, 3 samples, 3 RT reactions, and 3 qPCRs and quantified the expression of several genes in solid tissue, blood, cell culture, and single cells. A nested ANOVA design was used to model the experiments, and relative and absolute errors were calculated with this model for each processing level in the hierarchical design. We found that intersubject differences became easily confounded by sample heterogeneity for single cells and solid tissue. In cell cultures and blood, the noise from the RT and qPCR steps contributed substantially to the overall error because the sampling noise was less pronounced. We recommend the use of sample replicates preferentially to any other replicates when working with solid tissue, cell cultures, and single cells, and we recommend the use of RT replicates when working with blood. We show how an optimal sampling plan can be calculated for a limited budget. .

Effects of spacer orientations on the cake formation during membrane fouling: Quantitative analysis based on 3D OCT imaging.

PubMed

Liu, Xin; Li, Weiyi; Chong, Tzyy Haur; Fane, Anthony G

2017-03-01

Spacer design plays an important role in improving the performance of membrane processes for water/wastewater treatment. This work focused on a fundamental issue of spacer design, i.e., investigating the effects of spacer orientations on the fouling behavior during a membrane process. A series of fouling experiments with different spacer orientation were carried out to in situ characterize the formation of a cake layer in a spacer unit cell via 3D optical coherence tomography (OCT) imaging. The cake layers formed at different times were digitalized for quantitatively analyzing the variation in the cake morphology as a function of time. In particular, the local deposition rates were evaluated to determine the active regions where the instantaneous changes in deposit thickness were significant. The characterization results indicate that varying the spacer orientation could substantially change the evolution of membrane fouling by particulate foulants and thereby result in a cake layer with various morphologies; the competition between growth and erosion at different locations would instantaneously respond to the micro-hydrodynamic environment that might change with time. This work confirms that the OCT-based characterization method is a powerful tool for exploring novel spacer design. Copyright © 2016 Elsevier Ltd. All rights reserved.

Solving Constraint Satisfaction Problems with Networks of Spiking Neurons

PubMed Central

Jonke, Zeno; Habenschuss, Stefan; Maass, Wolfgang

2016-01-01

Network of neurons in the brain apply—unlike processors in our current generation of computer hardware—an event-based processing strategy, where short pulses (spikes) are emitted sparsely by neurons to signal the occurrence of an event at a particular point in time. Such spike-based computations promise to be substantially more power-efficient than traditional clocked processing schemes. However, it turns out to be surprisingly difficult to design networks of spiking neurons that can solve difficult computational problems on the level of single spikes, rather than rates of spikes. We present here a new method for designing networks of spiking neurons via an energy function. Furthermore, we show how the energy function of a network of stochastically firing neurons can be shaped in a transparent manner by composing the networks of simple stereotypical network motifs. We show that this design approach enables networks of spiking neurons to produce approximate solutions to difficult (NP-hard) constraint satisfaction problems from the domains of planning/optimization and verification/logical inference. The resulting networks employ noise as a computational resource. Nevertheless, the timing of spikes plays an essential role in their computations. Furthermore, networks of spiking neurons carry out for the Traveling Salesman Problem a more efficient stochastic search for good solutions compared with stochastic artificial neural networks (Boltzmann machines) and Gibbs sampling. PMID:27065785

Uncooled infrared imaging using bimaterial microcantilever arrays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grbovic, Dragoslav; Lavrik, Nickolay V; Rajic, Slobodan

2006-01-01

We report on the fabrication and characterization of microcantilever based uncooled focal plane array (FPA) for infrared imaging. By combining a streamlined design of microcantilever thermal transducers with a highly efficient optical readout, we minimized the fabrication complexity while achieving a competitive level of imaging performance. The microcantilever FPAs were fabricated using a straightforward fabrication process that involved only three photolithographic steps (i.e. three masks). A designed and constructed prototype of an IR imager employed a simple optical readout based on a noncoherent low-power light source. The main figures of merit of the IR imager were found to be comparablemore » to those of uncooled MEMS infrared detectors with substantially higher degree of fabrication complexity. In particular, the NETD and the response time of the implemented MEMS IR detector were measured to be as low as 0.5K and 6 ms, respectively. The potential of the implemented designs can also be concluded from the fact that the constructed prototype enabled IR imaging of close to room temperature objects without the use of any advanced data processing. The most unique and practically valuable feature of the implemented FPAs, however, is their scalability to high resolution formats, such as 2000x2000, without progressively growing device complexity and cost.« less

Structural design and fabrication techniques of composite unmanned aerial vehicles

NASA Astrophysics Data System (ADS)

Hunt, Daniel Stephen

Popularity of unmanned aerial vehicles has grown substantially in recent years both in the private sector, as well as for government functions. This growth can be attributed largely to the increased performance of the technology that controls these vehicles, as well as decreasing cost and size of this technology. What is sometimes forgotten though, is that the research and advancement of the airframes themselves are equally as important as what is done with them. With current computer-aided design programs, the limits of design optimization can be pushed further than ever before, resulting in lighter and faster airframes that can achieve longer endurances, higher altitudes, and more complex missions. However, realization of a paper design is still limited by the physical restrictions of the real world and the structural constraints associated with it. The purpose of this paper is to not only step through current design and manufacturing processes of composite UAVs at Oklahoma State University, but to also focus on composite spars, utilizing and relating both calculated and empirical data. Most of the experience gained for this thesis was from the Cessna Longitude project. The Longitude is a 1/8 scale, flying demonstrator Oklahoma State University constructed for Cessna. For the project, Cessna required dynamic flight data for their design process in order to make their 2017 release date. Oklahoma State University was privileged enough to assist Cessna with the mission of supporting the validation of design of their largest business jet to date. This paper will detail the steps of the fabrication process used in construction of the Longitude, as well as several other projects, beginning with structural design, machining, molding, skin layup, and ending with final assembly. Also, attention will be paid specifically towards spar design and testing in effort to ease the design phase. This document is intended to act not only as a further development of current practices, but also as a step-by-step manual for those who aspire to make composite airframes, predominantly the Oklahoma State University MAE students who either are, or will be using these techniques on a daily basis.

Edge detection - Image-plane versus digital processing

NASA Technical Reports Server (NTRS)

Huck, Friedrich O.; Fales, Carl L.; Park, Stephen K.; Triplett, Judith A.

1987-01-01

To optimize edge detection with the familiar Laplacian-of-Gaussian operator, it has become common to implement this operator with a large digital convolution mask followed by some interpolation of the processed data to determine the zero crossings that locate edges. It is generally recognized that this large mask causes substantial blurring of fine detail. It is shown that the spatial detail can be improved by a factor of about four with either the Wiener-Laplacian-of-Gaussian filter or an image-plane processor. The Wiener-Laplacian-of-Gaussian filter minimizes the image-gathering degradations if the scene statistics are at least approximately known and also serves as an interpolator to determine the desired zero crossings directly. The image-plane processor forms the Laplacian-of-Gaussian response by properly combining the optical design of the image-gathering system with a minimal three-by-three lateral-inhibitory processing mask. This approach, which is suggested by Marr's model of early processing in human vision, also reduces data processing by about two orders of magnitude and data transmission by up to an order of magnitude.

Academic plastic surgery: faculty recruitment and retention.

PubMed

Chen, Jenny T; Girotto, John A; Kitzmiller, W John; Lawrence, W Thomas; Verheyden, Charles N; Vedder, Nicholas B; Coleman, John J; Bentz, Michael L

2014-03-01

A critical element of a thriving academic plastic surgery program is the quality of faculty. A decline in recruitment and retention of faculty has been attributed to the many challenges of academic medicine. Given the substantial resources required to develop faculty, academic plastic surgery has a vested interest in improving the process of faculty recruitment and retention. The American Council of Academic Plastic Surgeons Issues Committee and the American Society of Plastic Surgeons/Plastic Surgery Foundation Academic Affairs Council surveyed the 83 existing programs in academic plastic surgery in February of 2012. The survey addressed the faculty-related issues in academic plastic surgery programs over the past decade. Recruitment and retention strategies were evaluated. This study was designed to elucidate trends, and define best strategies, on a national level. Academic plastic surgery programs have added substantially more full-time faculty over the past decade. Recruitment efforts are multifaceted and can include guaranteed salary support, moving expenses, nurse practitioner/physician's assistant hires, protected time for research, seed funds to start research programs, and more. Retention efforts can include increased compensation, designation of a leadership appointment, protected academic time, and call dilution. Significant change and growth of academic plastic surgery has occurred in the past decade. Effective faculty recruitment and retention are critical to a successful academic center. Funding sources in addition to physician professional fees (institutional program support, grants, contracts, endowment, and so on) are crucial to sustain the academic missions.

Optical guidance vidicon test program

NASA Technical Reports Server (NTRS)

Eiseman, A. R.; Stanton, R. H.; Voge, C. C.

1976-01-01

A laboratory and field test program was conducted to quantify the optical navigation parameters of the Mariner vidicons. A scene simulator and a camera were designed and built for vidicon tests under a wide variety of conditions. Laboratory tests characterized error sources important to the optical navigation process and field tests verified star sensitivity and characterized comet optical guidance parameters. The equipment, tests and data reduction techniques used are described. Key test results are listed. A substantial increase in the understanding of the use of selenium vidicons as detectors for spacecraft optical guidance was achieved, indicating a reduction in residual offset errors by a factor of two to four to the single pixel level.

Introduction to the mining of clinical data.

PubMed

Harrison, James H

2008-03-01

The increasing volume of medical data online, including laboratory data, represents a substantial resource that can provide a foundation for improved understanding of disease presentation, response to therapy, and health care delivery processes. Data mining supports these goals by providing a set of techniques designed to discover similarities and relationships between data elements in large data sets. Currently, medical data have several characteristics that increase the difficulty of applying these techniques, although there have been notable medical data mining successes. Future developments in integrated medical data repositories, standardized data representation, and guidelines for the appropriate research use of medical data will decrease the barriers to mining projects.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salmilehto, J.; Deppe, F.; Di Ventra, M.

Memristors are resistive elements retaining information of their past dynamics. They have garnered substantial interest due to their potential for representing a paradigm change in electronics, information processing and unconventional computing. Given the advent of quantum technologies, a design for a quantum memristor with superconducting circuits may be envisaged. Along these lines, we introduce such a quantum device whose memristive behavior arises from quasiparticle-induced tunneling when supercurrents are cancelled. Here in this paper, for realistic parameters, we find that the relevant hysteretic behavior may be observed using current state-of-the-art measurements of the phase-driven tunneling current. Finally, we develop suitable methodsmore » to quantify memory retention in the system.« less

Quantum Memristors with Superconducting Circuits

PubMed Central

Salmilehto, J.; Deppe, F.; Di Ventra, M.; Sanz, M.; Solano, E.

2017-01-01

Memristors are resistive elements retaining information of their past dynamics. They have garnered substantial interest due to their potential for representing a paradigm change in electronics, information processing and unconventional computing. Given the advent of quantum technologies, a design for a quantum memristor with superconducting circuits may be envisaged. Along these lines, we introduce such a quantum device whose memristive behavior arises from quasiparticle-induced tunneling when supercurrents are cancelled. For realistic parameters, we find that the relevant hysteretic behavior may be observed using current state-of-the-art measurements of the phase-driven tunneling current. Finally, we develop suitable methods to quantify memory retention in the system. PMID:28195193

A powerful test for Balaam's design.

PubMed

Mori, Joji; Kano, Yutaka

2015-01-01

The crossover trial design (AB/BA design) is often used to compare the effects of two treatments in medical science because it performs within-subject comparisons, which increase the precision of a treatment effect (i.e., a between-treatment difference). However, the AB/BA design cannot be applied in the presence of carryover effects and/or treatments-by-period interaction. In such cases, Balaam's design is a more suitable choice. Unlike the AB/BA design, Balaam's design inflates the variance of an estimate of the treatment effect, thereby reducing the statistical power of tests. This is a serious drawback of the design. Although the variance of parameter estimators in Balaam's design has been extensively studied, the estimators of the treatment effect to improve the inference have received little attention. If the estimate of the treatment effect is obtained by solving the mixed model equations, the AA and BB sequences are excluded from the estimation process. In this study, we develop a new estimator of the treatment effect and a new test statistic using the estimator. The aim is to improve the statistical inference in Balaam's design. Simulation studies indicate that the type I error of the proposed test is well controlled, and that the test is more powerful and has more suitable characteristics than other existing tests when interactions are substantial. The proposed test is also applied to analyze a real dataset. Copyright © 2015 John Wiley & Sons, Ltd.

SKIRT: Hybrid parallelization of radiative transfer simulations

NASA Astrophysics Data System (ADS)

Verstocken, S.; Van De Putte, D.; Camps, P.; Baes, M.

2017-07-01

We describe the design, implementation and performance of the new hybrid parallelization scheme in our Monte Carlo radiative transfer code SKIRT, which has been used extensively for modelling the continuum radiation of dusty astrophysical systems including late-type galaxies and dusty tori. The hybrid scheme combines distributed memory parallelization, using the standard Message Passing Interface (MPI) to communicate between processes, and shared memory parallelization, providing multiple execution threads within each process to avoid duplication of data structures. The synchronization between multiple threads is accomplished through atomic operations without high-level locking (also called lock-free programming). This improves the scaling behaviour of the code and substantially simplifies the implementation of the hybrid scheme. The result is an extremely flexible solution that adjusts to the number of available nodes, processors and memory, and consequently performs well on a wide variety of computing architectures.

Computational aerodynamics and artificial intelligence

NASA Technical Reports Server (NTRS)

Mehta, U. B.; Kutler, P.

1984-01-01

The general principles of artificial intelligence are reviewed and speculations are made concerning how knowledge based systems can accelerate the process of acquiring new knowledge in aerodynamics, how computational fluid dynamics may use expert systems, and how expert systems may speed the design and development process. In addition, the anatomy of an idealized expert system called AERODYNAMICIST is discussed. Resource requirements for using artificial intelligence in computational fluid dynamics and aerodynamics are examined. Three main conclusions are presented. First, there are two related aspects of computational aerodynamics: reasoning and calculating. Second, a substantial portion of reasoning can be achieved with artificial intelligence. It offers the opportunity of using computers as reasoning machines to set the stage for efficient calculating. Third, expert systems are likely to be new assets of institutions involved in aeronautics for various tasks of computational aerodynamics.

Pilot users in agile development processes: motivational factors.

PubMed

Johannessen, Liv Karen; Gammon, Deede

2010-01-01

Despite a wealth of research on user participation, few studies offer insights into how to involve multi-organizational users in agile development methods. This paper is a case study of user involvement in developing a system for electronic laboratory requisitions using agile methodologies in a multi-organizational context. Building on an interpretive approach, we illuminate questions such as: How does collaboration between users and developers evolve and how might it be improved? What key motivational aspects are at play when users volunteer and continue contributing in the face of considerable added burdens? The study highlights how agile methods in themselves appear to facilitate mutually motivating collaboration between user groups and developers. Lessons learned for leveraging the advantages of agile development processes include acknowledging the substantial and ongoing contributions of users and their roles as co-designers of the system.

40 CFR 53.1 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... substantial deviations from the design specifications of the sampler specified for reference methods in... general requirements as an ISO 9001-registered facility for the design and manufacture of designated... capable of automatically collecting a series of sequential samples. NO means nitrogen oxide. NO 2 means...

Communication Design Education: Could Nine Reflections Be Sufficient?

ERIC Educational Resources Information Center

van der Waarde, Karel; Vroombout, Maurits

2012-01-01

Situation: Graphic design education is subject to substantial changes. Changes in professional practice and higher education aggravate insecurities about the contents and structure of courses, assessment criteria, relations between practice, research and theory and teaching methods. Assumption: Graphic design education (visual communication design…

Study of design and technology factors influencing gas turbine blade cooling

NASA Astrophysics Data System (ADS)

Shevchenko, I. V.; Garanin, I. V.; Rogalev, A. N.; Kindra, V. O.; Khudyakova, V. P.

2017-11-01

The knowledge of aerodynamic and thermal parameters of turbulators used in order to design an efficient blade cooling system. However, all experimental tests of the hydraulic and thermal characteristics of the turbulators were conducted on the rectangular shape channels with a strongly defined air flow direction. The actual blades have geometry of the channels that essentially differs from the rectangular shape. Specifically, the air flow in the back cavity of a blade with one and half-pass cooling channel changes its direction throughout the feather height. In most cases the ribs and pins are made with a tilt to the channel walls, which is determined by the moving element design of a mould for the ceramic rod element fabrication. All of the factors described above may result in the blade thermohydraulic model being developed failing to fully simulate the air flow and the heat exchange processes in some sections of the cooling path. Hence, the design temperature field will differ from the temperature field of an actual blade. This article studied the numerical data of design and technology factors influencing heat transfer in the cooling channels. The results obtained showed their substantial impact on the blade cooling efficiency.

Considering RNAi experimental design in parasitic helminths.

PubMed

Dalzell, Johnathan J; Warnock, Neil D; McVeigh, Paul; Marks, Nikki J; Mousley, Angela; Atkinson, Louise; Maule, Aaron G

2012-04-01

Almost a decade has passed since the first report of RNA interference (RNAi) in a parasitic helminth. Whilst much progress has been made with RNAi informing gene function studies in disparate nematode and flatworm parasites, substantial and seemingly prohibitive difficulties have been encountered in some species, hindering progress. An appraisal of current practices, trends and ideals of RNAi experimental design in parasitic helminths is both timely and necessary for a number of reasons: firstly, the increasing availability of parasitic helminth genome/transcriptome resources means there is a growing need for gene function tools such as RNAi; secondly, fundamental differences and unique challenges exist for parasite species which do not apply to model organisms; thirdly, the inherent variation in experimental design, and reported difficulties with reproducibility undermine confidence. Ideally, RNAi studies of gene function should adopt standardised experimental design to aid reproducibility, interpretation and comparative analyses. Although the huge variations in parasite biology and experimental endpoints make RNAi experimental design standardization difficult or impractical, we must strive to validate RNAi experimentation in helminth parasites. To aid this process we identify multiple approaches to RNAi experimental validation and highlight those which we deem to be critical for gene function studies in helminth parasites.

Design keys for paper-based concentration gradient generators.

PubMed

Schaumburg, Federico; Urteaga, Raúl; Kler, Pablo A; Berli, Claudio L A

2018-08-03

The generation of concentration gradients is an essential operation for several analytical processes implemented on microfluidic paper-based analytical devices. The dynamic gradient formation is based on the transverse dispersion of chemical species across co-flowing streams. In paper channels, this transverse flux of molecules is dominated by mechanical dispersion, which is substantially different than molecular diffusion, which is the mechanism acting in conventional microchannels. Therefore, the design of gradient generators on paper requires strategies different from those used in traditional microfluidics. This work considers the foundations of transverse dispersion in porous substrates to investigate the optimal design of microfluidic paper-based concentration gradient generators (μPGGs) by computer simulations. A set of novel and versatile μPGGs were designed in the format of numerical prototypes, and virtual experiments were run to explore the ranges of operation and the overall performance of such devices. Then physical prototypes were fabricated and experimentally tested in our lab. Finally, some basic rules for the design of optimized μPGGs are proposed. Apart from improving the efficiency of mixers, diluters and μPGGs, the results of this investigation are relevant to attain highly controlled concentration fields on paper-based devices. Copyright © 2018 Elsevier B.V. All rights reserved.

Method of fabricating a uranium-bearing foil

DOEpatents

Gooch, Jackie G [Seymour, TN; DeMint, Amy L [Kingston, TN

2012-04-24

Methods of fabricating a uranium-bearing foil are described. The foil may be substantially pure uranium, or may be a uranium alloy such as a uranium-molybdenum alloy. The method typically includes a series of hot rolling operations on a cast plate material to form a thin sheet. These hot rolling operations are typically performed using a process where each pass reduces the thickness of the plate by a substantially constant percentage. The sheet is typically then annealed and then cooled. The process typically concludes with a series of cold rolling passes where each pass reduces the thickness of the plate by a substantially constant thickness amount to form the foil.

Strategic funding priorities in the pharmaceutical sciences allied to Quality by Design (QbD) and Process Analytical Technology (PAT).

PubMed

Aksu, Buket; De Beer, Thomas; Folestad, Staffan; Ketolainen, Jarkko; Lindén, Hans; Lopes, Joao Almeida; de Matas, Marcel; Oostra, Wim; Rantanen, Jukka; Weimer, Marco

2012-09-29

Substantial changes in Pharmaceutical R&D strategy are required to address existing issues of low productivity, imminent patent expirations and pressures on pricing. Moves towards personalized healthcare and increasing diversity in the nature of portfolios including the rise of biopharmaceuticals however have the potential to provide considerable challenges to the establishment of cost effective and robust supply chains. To guarantee product quality and surety of supply for essential medicines it is necessary that manufacturing science keeps pace with advances in pharmaceutical R&D. In this position paper, the EUFEPS QbD and PAT Sciences network make recommendations that European industry, academia and health agencies focus attention on delivering step changes in science and technology in a number of key themes. These subject areas, all underpinned by the sciences allied to QbD and PAT, include product design and development for personalized healthcare, continuous-processing in pharmaceutical product manufacture, quantitative quality risk assessment for pharmaceutical development including life cycle management and the downstream processing of biopharmaceutical products. Plans are being established to gain commitment for inclusion of these themes into future funding priorities for the Innovative Medicines Initiative (IMI). Copyright © 2012 Elsevier B.V. All rights reserved.

Optical and optomechanical ultralightweight C/SiC components

NASA Astrophysics Data System (ADS)

Papenburg, Ulrich; Pfrang, Wilhelm; Kutter, G. S.; Mueller, Claus E.; Kunkel, Bernd P.; Deyerler, Michael; Bauereisen, Stefan

1999-11-01

Optical and optomechanical structures based on silicon carbide (SiC) ceramics are becoming increasingly important for ultra- lightweight optical systems that must work in adverse environments. At IABG and Dornier Satellite Systems (DSS) in Munich, a special form of SiC ceramics carbon fiber reinforced silicon carbide (C/SiCR) has been developed partly under ESA and NASA contracts. C/SiCR is a light-weight, high- strength engineering material that features tunable mechanical and thermal properties. It offers exceptional design freedom due to its reduced brittleness and negligible volume shrinkage during processing in comparison to traditional, powder-based ceramics. Furthermore, its rapid fabrication process produces near-net-shape components using conventional NC machining/milling equipment and, thus, provides substantial schedule, cost, and risk savings. These characteristics allow C/SiCR to overcome many of the problems associated with more traditional optical materials. To date, C/SiCR has been used to produce ultra-lightweight mirrors and reflectors, antennas, optical benches, and monolithic and integrated reference structures for a variety of space and terrestrial applications. This paper describes the material properties, optical system and structural design aspects, the forming and manufacturing process including high-temperature joining technology, precision grinding and cladding techniques, and the performance results of a number of C/SiCR optical components we have built.

Direct electron-pair production by high energy heavy charged particles

NASA Technical Reports Server (NTRS)

Takahashi, Y.; Gregory, J. C.; Hayashi, T.; Dong, B. L.

1989-01-01

Direct electron pain production via virtual photons by moving charged particles is a unique electro-magnetic process having a substantial dependence on energy. Most electro-magnetic processes, including transition radiation, cease to be sensitive to the incident energy above 10 TeV/AMU. Thus, it is expected, that upon establishment of cross section and detection efficiency of this process, it may provide a new energy measuring technique above 10 TeV/AMU. Three accelerator exposures of emulsion chambers designed for measurements of direct electron-pains were performed. The objectives of the investigation were to provide the fundamental cross-section data in emulsion stacks to find the best-fit theoretical model, and to provide a calibration of measurements of direct electron-pairs in emulsion chamber configurations. This paper reports the design of the emulsion chambers, accelerator experiments, microscope measurements, and related considerations for future improvements of the measurements, and for possible applications to high energy cosmic ray experiments. Also discussed are the results from scanning 56m of emulsion tracks at 1200x magnification so that scanning efficiency is optimized. Measurements of the delta-ray range spectrum were also performed for much shorter track lengths, but with sufficiently large statistics in the number of measured delta-rays.

Bioprocess development workflow: Transferable physiological knowledge instead of technological correlations.

PubMed

Reichelt, Wieland N; Haas, Florian; Sagmeister, Patrick; Herwig, Christoph

2017-01-01

Microbial bioprocesses need to be designed to be transferable from lab scale to production scale as well as between setups. Although substantial effort is invested to control technological parameters, usually the only true constant parameter is the actual producer of the product: the cell. Hence, instead of solely controlling technological process parameters, the focus should be increasingly laid on physiological parameters. This contribution aims at illustrating a workflow of data life cycle management with special focus on physiology. Information processing condenses the data into physiological variables, while information mining condenses the variables further into physiological descriptors. This basis facilitates data analysis for a physiological explanation for observed phenomena in productivity. Targeting transferability, we demonstrate this workflow using an industrially relevant Escherichia coli process for recombinant protein production and substantiate the following three points: (1) The postinduction phase is independent in terms of productivity and physiology from the preinduction variables specific growth rate and biomass at induction. (2) The specific substrate uptake rate during induction phase was found to significantly impact the maximum specific product titer. (3) The time point of maximum specific titer can be predicted by an easy accessible physiological variable: while the maximum specific titers were reached at different time points (19.8 ± 7.6 h), those maxima were reached all within a very narrow window of cumulatively consumed substrate dSn (3.1 ± 0.3 g/g). Concluding, this contribution provides a workflow on how to gain a physiological view on the process and illustrates potential benefits. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 33:261-270, 2017. © 2016 American Institute of Chemical Engineers.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Looney, J.H.; Im, C.J.

Under the sponsorship of DOE/METC, UCC Research completed a program in 1984 concerned with the development, testing, and manufacture of an ultra-clean coal-water mixture fuel using the UCC two-stage physical beneficiation and coal-water mixture preparation process. Several gallons of ultra-clean coal-water slurry produced at the UCC Research pilot facility was supplied to DOE/METC for combustion testing. The finalization of this project resulted in the presentation of a conceptual design and economic analysis of an ultra-clean coal-water mixture processing facility sufficient in size to continuously supply fuel to a 100 MW turbine power generation system. Upon completion of the above program,more » it became evident that substantial technological and economic improvement could be realized through further laboratory and engineering investigation of the UCC two-stage physical beneficiation process. Therefore, as an extension to the previous work, the purpose of the present program was to define the relationship between the controlling technical parameters as related to coal-water slurry quality and product price, and to determine the areas of improvement in the existing flow-scheme, associated cost savings, and the overall effect of these savings on final coal-water slurry price. Contents of this report include: (1) introduction; (2) process refinement (improvement of coal beneficiation process, different source coals and related cleanability, dispersants and other additives); (3) coal beneficiation and cost parametrics summary; (4) revised conceptual design and economic analysis; (5) operating and capital cost reduction; (6) conclusion; and (7) appendices. 24 figs., 12 tabs.« less

14 CFR 21.97 - Approval of major changes in type design.

Code of Federal Regulations, 2011 CFR

2011-01-01

... necessary descriptive data for inclusion in the type design the other configurations of the same engine type... for approval of a major change in type design must— (1) Provide substantiating data and necessary descriptive data for inclusion in the type design; (2) Show that the changed product complies with the...

14 CFR 21.97 - Approval of major changes in type design.

Code of Federal Regulations, 2013 CFR

2013-01-01

.... (a) An applicant for approval of a major change in type design must— (1) Provide substantiating data and necessary descriptive data for inclusion in the type design; (2) Show that the changed product... the necessary descriptive data for inclusion in the type design the other configurations of the same...

Design as Storytelling

ERIC Educational Resources Information Center

Parrish, Patrick

2006-01-01

Technical problem solving as a model for instructional design (ID) has its strengths, and it has done much to provide designers strategies for their work, but it has substantial limitations as well. For one, it does not do a good job in describing how designers actually think. Slavish adherence to its methods can also be considered responsible for…

Designing for Interaction: Six Steps to Designing Computer-Supported Group-Based Learning

ERIC Educational Resources Information Center

Strijbos, J. W.; Martens, R. L.; Jochems, W. M. G.

2004-01-01

At present, the design of computer-supported group-based learning (CSGBL) is often based on subjective decisions regarding tasks, pedagogy and technology, or concepts such as "cooperative learning" and "collaborative learning." Critical review reveals these concepts as insufficiently substantial to serve as a basis for CSGBL design. Furthermore,…

78 FR 25501 - Self-Regulatory Organizations; The NASDAQ Stock Market LLC; Notice of Designation of a Longer...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-01

... SECURITIES AND EXCHANGE COMMISSION [Release No. 34-69450; File No. SR-NASDAQ-2013-031] Self... Member Organization To Attest That ``Substantially All'' Orders Submitted to the Retail Price Improvement... ``substantially all,'' rather than all, orders submitted to the Retail Price Improvement Program qualify as...

10 CFR 950.3 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., tests, analyses and acceptance criteria established under the combined license; (2) The conduct of pre... facility the reactor design for which is approved after December 31, 1993, by the Nuclear Regulatory Commission (and such design or a substantially similar design of comparable capacity was not approved on or...

10 CFR 950.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., tests, analyses and acceptance criteria established under the combined license; (2) The conduct of pre... facility the reactor design for which is approved after December 31, 1993, by the Nuclear Regulatory Commission (and such design or a substantially similar design of comparable capacity was not approved on or...

10 CFR 950.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., tests, analyses and acceptance criteria established under the combined license; (2) The conduct of pre... facility the reactor design for which is approved after December 31, 1993, by the Nuclear Regulatory Commission (and such design or a substantially similar design of comparable capacity was not approved on or...

10 CFR 950.3 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., tests, analyses and acceptance criteria established under the combined license; (2) The conduct of pre... facility the reactor design for which is approved after December 31, 1993, by the Nuclear Regulatory Commission (and such design or a substantially similar design of comparable capacity was not approved on or...

10 CFR 950.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., tests, analyses and acceptance criteria established under the combined license; (2) The conduct of pre... facility the reactor design for which is approved after December 31, 1993, by the Nuclear Regulatory Commission (and such design or a substantially similar design of comparable capacity was not approved on or...

Application of probiotics in food products--challenges and new approaches.

PubMed

Jankovic, I; Sybesma, W; Phothirath, P; Ananta, E; Mercenier, A

2010-04-01

The probiotic research conducted over the past 20 years has resulted in a valuable source of data related to health beneficial effects of probiotics. Nevertheless, documentation of probiotic benefits remains challenging, especially in functional foods that are designed for the generally healthy population that, however, regularly experiences episodes of 'suboptimal' health. In addition, in view of today's application of probiotics in an increasing variety of food matrixes, process optimization and product design need to take into account cell viability and probiotic function altogether. To meet this challenge, medium to high-throughput bioassays - based on the identification of active compounds and their mechanism of action - have to be developed and their predictive value established. Together with validated biomarkers for health and disease, this should help rationalize probiotic product development and associated health claim substantiation in human studies. Copyright 2010 Elsevier Ltd. All rights reserved.

Large scale rigidity-based flexibility analysis of biomolecules

PubMed Central

Streinu, Ileana

2016-01-01

KINematics And RIgidity (KINARI) is an on-going project for in silico flexibility analysis of proteins. The new version of the software, Kinari-2, extends the functionality of our free web server KinariWeb, incorporates advanced web technologies, emphasizes the reproducibility of its experiments, and makes substantially improved tools available to the user. It is designed specifically for large scale experiments, in particular, for (a) very large molecules, including bioassemblies with high degree of symmetry such as viruses and crystals, (b) large collections of related biomolecules, such as those obtained through simulated dilutions, mutations, or conformational changes from various types of dynamics simulations, and (c) is intended to work as seemlessly as possible on the large, idiosyncratic, publicly available repository of biomolecules, the Protein Data Bank. We describe the system design, along with the main data processing, computational, mathematical, and validation challenges underlying this phase of the KINARI project. PMID:26958583

Nature-inspired polymer actuators for micro-fluidic mixing.

NASA Astrophysics Data System (ADS)

den Toonder, Jaap M. J.; Bos, Femke; de Goede, Judith; Anderson, Patrick

2007-11-01

One particular micro-fluidics manipulation mechanism ``designed'' by nature is that due to a covering of beating cilia over the external surface of micro-organisms (e.g. Paramecium). A cilium can be viewed as a small hair or flexible rod (in protozoa: typical length 10 microns and diameter 0.1 microns) which is attached to the surface. We have developed polymer micro-actuators, made with standard micro-technology processing, which respond to an applied electrical or magnetic field by changing their shape. The shape and size of the polymer actuators mimics that of cilia occurring in nature. Flow visualization experiments show that the cilia can generate substantial fluid velocities, in the order of 1 mm/s. In addition, using specially designed geometrical configurations of the cilia, very efficient mixing is obtained. Since the artificial cilia can be actively controlled using electrical signals, they have exciting applications in micro-fluidic devices.

Hydrogen tunneling links protein dynamics to enzyme catalysis.

PubMed

Klinman, Judith P; Kohen, Amnon

2013-01-01

The relationship between protein dynamics and function is a subject of considerable contemporary interest. Although protein motions are frequently observed during ligand binding and release steps, the contribution of protein motions to the catalysis of bond making/breaking processes is more difficult to probe and verify. Here, we show how the quantum mechanical hydrogen tunneling associated with enzymatic C-H bond cleavage provides a unique window into the necessity of protein dynamics for achieving optimal catalysis. Experimental findings support a hierarchy of thermodynamically equilibrated motions that control the H-donor and -acceptor distance and active-site electrostatics, creating an ensemble of conformations suitable for H-tunneling. A possible extension of this view to methyl transfer and other catalyzed reactions is also presented. The impact of understanding these dynamics on the conceptual framework for enzyme activity, inhibitor/drug design, and biomimetic catalyst design is likely to be substantial.

Hydrogen Tunneling Links Protein Dynamics to Enzyme Catalysis

PubMed Central

Klinman, Judith P.; Kohen, Amnon

2014-01-01

The relationship between protein dynamics and function is a subject of considerable contemporary interest. Although protein motions are frequently observed during ligand binding and release steps, the contribution of protein motions to the catalysis of bond making/breaking processes is more difficult to probe and verify. Here, we show how the quantum mechanical hydrogen tunneling associated with enzymatic C–H bond cleavage provides a unique window into the necessity of protein dynamics for achieving optimal catalysis. Experimental findings support a hierarchy of thermodynamically equilibrated motions that control the H-donor and -acceptor distance and active-site electrostatics, creating an ensemble of conformations suitable for H-tunneling. A possible extension of this view to methyl transfer and other catalyzed reactions is also presented. The impact of understanding these dynamics on the conceptual framework for enzyme activity, inhibitor/drug design, and biomimetic catalyst design is likely to be substantial. PMID:23746260

COPYCAT; IBM OS system catalog utility routine. [IBM360,370; Assembly language

DOE Office of Scientific and Technical Information (OSTI.GOV)

Engert, D.E.

COPYCAT is an OS utility program designed to produce an efficient system-wide catalog which may reside on many volumes. Substantial improvement in performance may also be obtained on a system with only a single catalog. First, catalog entries from many different catalogs may be redistributed to equalize the load on each catalog. Second, each individual catalog is restructured in a way designed to minimize the I/O time required for searching and updating. Redistribution and restructuring parameters are under user control. Model DSCB's for generation data groups and alias entries are also processed. Catalogs on all direct access devices, including datamore » cells, are supported. Backup copies may also be made.IBM360,370; Assembly language; OS/MVT, OS/MFT, OS/VS1 and OS/VS2 Release 1; A large region size is recommended since COPYCAT will use all of the core available to it for buffers..« less

Trash to treasure: production of biofuels and commodity chemicals via syngas fermenting microorganisms.

PubMed

Latif, Haythem; Zeidan, Ahmad A; Nielsen, Alex T; Zengler, Karsten

2014-06-01

Fermentation of syngas is a means through which unutilized organic waste streams can be converted biologically into biofuels and commodity chemicals. Despite recent advances, several issues remain which limit implementation of industrial-scale syngas fermentation processes. At the cellular level, the energy conservation mechanism of syngas fermenting microorganisms has not yet been entirely elucidated. Furthermore, there was a lack of genetic tools to study and ultimately enhance their metabolic capabilities. Recently, substantial progress has been made in understanding the intricate energy conservation mechanisms of these microorganisms. Given the complex relationship between energy conservation and metabolism, strain design greatly benefits from systems-level approaches. Numerous genetic manipulation tools have also been developed, paving the way for the use of metabolic engineering and systems biology approaches. Rational strain designs can now be deployed resulting in desirable phenotypic traits for large-scale production. Copyright © 2013 Elsevier Ltd. All rights reserved.

Engineering of the LISA Pathfinder mission—making the experiment a practical reality

NASA Astrophysics Data System (ADS)

Warren, Carl; Dunbar, Neil; Backler, Mike

2009-05-01

LISA Pathfinder represents a unique challenge in the development of scientific spacecraft—not only is the LISA Test Package (LTP) payload a complex integrated development, placing stringent requirements on its developers and the spacecraft, but the payload also acts as the core sensor and actuator for the spacecraft, making the tasks of control design, software development and system verification unusually difficult. The micro-propulsion system which provides the remaining actuation also presents substantial development and verification challenges. As the mission approaches the system critical design review, flight hardware is completing verification and the process of verification using software and hardware simulators and test benches is underway. Preparation for operations has started, but critical milestones for LTP and field effect electric propulsion (FEEP) lie ahead. This paper summarizes the status of the present development and outlines the key challenges that must be overcome on the way to launch.

BioStar models of clinical and genomic data for biomedical data warehouse design

PubMed Central

Wang, Liangjiang; Ramanathan, Murali

2008-01-01

Biomedical research is now generating large amounts of data, ranging from clinical test results to microarray gene expression profiles. The scale and complexity of these datasets give rise to substantial challenges in data management and analysis. It is highly desirable that data warehousing and online analytical processing technologies can be applied to biomedical data integration and mining. The major difficulty probably lies in the task of capturing and modelling diverse biological objects and their complex relationships. This paper describes multidimensional data modelling for biomedical data warehouse design. Since the conventional models such as star schema appear to be insufficient for modelling clinical and genomic data, we develop a new model called BioStar schema. The new model can capture the rich semantics of biomedical data and provide greater extensibility for the fast evolution of biological research methodologies. PMID:18048122

Challenges to fair decision-making processes in the context of health care services: a qualitative assessment from Tanzania.

PubMed

Shayo, Elizabeth H; Norheim, Ole F; Mboera, Leonard E G; Byskov, Jens; Maluka, Stephen; Kamuzora, Peter; Blystad, Astrid

2012-06-07

Fair processes in decision making need the involvement of stakeholders who can discuss issues and reach an agreement based on reasons that are justifiable and appropriate in meeting people's needs. In Tanzania, the policy of decentralization and the health sector reform place an emphasis on community participation in making decisions in health care. However, aspects that can influence an individual's opportunity to be listened to and to contribute to discussion have been researched to a very limited extent in low-income settings. The objective of this study was to explore challenges to fair decision-making processes in health care services with a special focus on the potential influence of gender, wealth, ethnicity and education. We draw on the principle of fairness as outlined in the deliberative democratic theory. The study was carried out in the Mbarali District of Tanzania. A qualitative study design was used. In-depth interviews and focus group discussion were conducted among members of the district health team, local government officials, health care providers and community members. Informal discussion on the topics was also of substantial value. The study findings indicate a substantial influence of gender, wealth, ethnicity and education on health care decision-making processes. Men, wealthy individuals, members of strong ethnic groups and highly educated individuals had greater influence. Opinions varied among the study informants as to whether such differences should be considered fair. The differences in levels of influence emerged most clearly at the community level, and were largely perceived as legitimate. Existing challenges related to individuals' influence of decision making processes in health care need to be addressed if greater participation is desired. There is a need for increased advocacy and a strengthening of responsive practices with an emphasis on the right of all individuals to participate in decision-making processes. This simultaneously implies an emphasis on assuring the distribution of information, training and education so that individuals can participate fully in informed decision making.

Navigation Algorithms for the SeaWiFS Mission

NASA Technical Reports Server (NTRS)

Hooker, Stanford B. (Editor); Firestone, Elaine R. (Editor); Patt, Frederick S.; McClain, Charles R. (Technical Monitor)

2002-01-01

The navigation algorithms for the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) were designed to meet the requirement of 1-pixel accuracy-a standard deviation (sigma) of 2. The objective has been to extract the best possible accuracy from the spacecraft telemetry and avoid the need for costly manual renavigation or geometric rectification. The requirement is addressed by postprocessing of both the Global Positioning System (GPS) receiver and Attitude Control System (ACS) data in the spacecraft telemetry stream. The navigation algorithms described are separated into four areas: orbit processing, attitude sensor processing, attitude determination, and final navigation processing. There has been substantial modification during the mission of the attitude determination and attitude sensor processing algorithms. For the former, the basic approach was completely changed during the first year of the mission, from a single-frame deterministic method to a Kalman smoother. This was done for several reasons: a) to improve the overall accuracy of the attitude determination, particularly near the sub-solar point; b) to reduce discontinuities; c) to support the single-ACS-string spacecraft operation that was started after the first mission year, which causes gaps in attitude sensor coverage; and d) to handle data quality problems (which became evident after launch) in the direct-broadcast data. The changes to the attitude sensor processing algorithms primarily involved the development of a model for the Earth horizon height, also needed for single-string operation; the incorporation of improved sensor calibration data; and improved data quality checking and smoothing to handle the data quality issues. The attitude sensor alignments have also been revised multiple times, generally in conjunction with the other changes. The orbit and final navigation processing algorithms have remained largely unchanged during the mission, aside from refinements to data quality checking. Although further improvements are certainly possible, future evolution of the algorithms is expected to be limited to refinements of the methods presented here, and no substantial changes are anticipated.

Low-Power SOI CMOS Transceiver

NASA Technical Reports Server (NTRS)

Fujikawa, Gene (Technical Monitor); Cheruiyot, K.; Cothern, J.; Huang, D.; Singh, S.; Zencir, E.; Dogan, N.

2003-01-01

The work aims at developing a low-power Silicon on Insulator Complementary Metal Oxide Semiconductor (SOI CMOS) Transceiver for deep-space communications. RF Receiver must accomplish the following tasks: (a) Select the desired radio channel and reject other radio signals, (b) Amplify the desired radio signal and translate them back to baseband, and (c) Detect and decode the information with Low BER. In order to minimize cost and achieve high level of integration, receiver architecture should use least number of external filters and passive components. It should also consume least amount of power to minimize battery cost, size, and weight. One of the most stringent requirements for deep-space communication is the low-power operation. Our study identified that two candidate architectures listed in the following meet these requirements: (1) Low-IF receiver, (2) Sub-sampling receiver. The low-IF receiver uses minimum number of external components. Compared to Zero-IF (Direct conversion) architecture, it has less severe offset and flicker noise problems. The Sub-sampling receiver amplifies the RF signal and samples it using track-and-hold Subsampling mixer. These architectures provide low-power solution for the short- range communications missions on Mars. Accomplishments to date include: (1) System-level design and simulation of a Double-Differential PSK receiver, (2) Implementation of Honeywell SOI CMOS process design kit (PDK) in Cadence design tools, (3) Design of test circuits to investigate relationships between layout techniques, geometry, and low-frequency noise in SOI CMOS, (4) Model development and verification of on-chip spiral inductors in SOI CMOS process, (5) Design/implementation of low-power low-noise amplifier (LNA) and mixer for low-IF receiver, and (6) Design/implementation of high-gain LNA for sub-sampling receiver. Our initial results show that substantial improvement in power consumption is achieved using SOI CMOS as compared to standard CMOS process. Potential advantages of SOI CMOS for deep-space communication electronics include: (1) Radiation hardness, (2) Low-power operation, and (3) System-on-Chip (SOC) solutions.

Theoretical and experimental errors for in situ measurements of plant water potential.

PubMed

Shackel, K A

1984-07-01

Errors in psychrometrically determined values of leaf water potential caused by tissue resistance to water vapor exchange and by lack of thermal equilibrium were evaluated using commercial in situ psychrometers (Wescor Inc., Logan, UT) on leaves of Tradescantia virginiana (L.). Theoretical errors in the dewpoint method of operation for these sensors were demonstrated. After correction for these errors, in situ measurements of leaf water potential indicated substantial errors caused by tissue resistance to water vapor exchange (4 to 6% reduction in apparent water potential per second of cooling time used) resulting from humidity depletions in the psychrometer chamber during the Peltier condensation process. These errors were avoided by use of a modified procedure for dewpoint measurement. Large changes in apparent water potential were caused by leaf and psychrometer exposure to moderate levels of irradiance. These changes were correlated with relatively small shifts in psychrometer zero offsets (-0.6 to -1.0 megapascals per microvolt), indicating substantial errors caused by nonisothermal conditions between the leaf and the psychrometer. Explicit correction for these errors is not possible with the current psychrometer design.

Theoretical and Experimental Errors for In Situ Measurements of Plant Water Potential 1

PubMed Central

Shackel, Kenneth A.

1984-01-01

Errors in psychrometrically determined values of leaf water potential caused by tissue resistance to water vapor exchange and by lack of thermal equilibrium were evaluated using commercial in situ psychrometers (Wescor Inc., Logan, UT) on leaves of Tradescantia virginiana (L.). Theoretical errors in the dewpoint method of operation for these sensors were demonstrated. After correction for these errors, in situ measurements of leaf water potential indicated substantial errors caused by tissue resistance to water vapor exchange (4 to 6% reduction in apparent water potential per second of cooling time used) resulting from humidity depletions in the psychrometer chamber during the Peltier condensation process. These errors were avoided by use of a modified procedure for dewpoint measurement. Large changes in apparent water potential were caused by leaf and psychrometer exposure to moderate levels of irradiance. These changes were correlated with relatively small shifts in psychrometer zero offsets (−0.6 to −1.0 megapascals per microvolt), indicating substantial errors caused by nonisothermal conditions between the leaf and the psychrometer. Explicit correction for these errors is not possible with the current psychrometer design. PMID:16663701

Bayesian Optimal Interval Design: A Simple and Well-Performing Design for Phase I Oncology Trials.

PubMed

Yuan, Ying; Hess, Kenneth R; Hilsenbeck, Susan G; Gilbert, Mark R

2016-09-01

Despite more than two decades of publications that offer more innovative model-based designs, the classical 3 + 3 design remains the most dominant phase I trial design in practice. In this article, we introduce a new trial design, the Bayesian optimal interval (BOIN) design. The BOIN design is easy to implement in a way similar to the 3 + 3 design, but is more flexible for choosing the target toxicity rate and cohort size and yields a substantially better performance that is comparable with that of more complex model-based designs. The BOIN design contains the 3 + 3 design and the accelerated titration design as special cases, thus linking it to established phase I approaches. A numerical study shows that the BOIN design generally outperforms the 3 + 3 design and the modified toxicity probability interval (mTPI) design. The BOIN design is more likely than the 3 + 3 design to correctly select the MTD and allocate more patients to the MTD. Compared with the mTPI design, the BOIN design has a substantially lower risk of overdosing patients and generally a higher probability of correctly selecting the MTD. User-friendly software is freely available to facilitate the application of the BOIN design. Clin Cancer Res; 22(17); 4291-301. ©2016 AACR. ©2016 American Association for Cancer Research.

AP1000{sup R} licensing and deployment in the United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jordan, R. P.; Russ, P. A.; Filiak, P. P.

2012-07-01

In recent years, both domestic and foreign utilities have turned to the standardized Westinghouse AP1000 plant design in satisfying their near - and long-term - sustainable energy needs. As direct support to these actions, licensing the AP1000 design has played a significant role by providing one of the fundamental bases in clearing regulatory hurdles leading to the start of new plant construction. Within the U.S. alone, Westinghouse AP1000 licensing activities have reached unprecedented milestones with the approvals of both AP1000 Design Certification and Southern Company's combined construction permit and operating license (COL) application directly supporting the construction of two newmore » nuclear plants in Georgia. Further COL application approvals are immediately pending for an additional two AP1000 plants in South Carolina. And, across the U.S. nuclear industry spectrum, there are 10 other COL applications under regulatory review representing some 16 new plants at 10 sites. In total, these actions represent the first wave of new plant licensing under the regulatory approval process since 1978. Fundamental to the Nuclear Regulatory Commission's AP1000 Design Certification is the formal recognition of the AP1000 passive safety design through regulatory acceptance rulemaking. Through recognition and deployment of the AP1000 Design Certification, the utility licensee / operator of this reactor design are now offered an opportunity to use a simplified 'one-step' combined license process, thereby managing substantial back-end construction schedule risk from regulatory and intervention delays. Application of this regulatory philosophy represents both acceptance and encouragement of standardized reactor designs like the AP1000. With the recent AP1000 Design Certification and utility COL acceptances, the fundamental licensing processes of this philosophy have successfully proven the attainment of significant milestones with the next stage licensing actions directed towards deployment. AP1000 Design Certification and COL deployment, and management of the plant construction in accordance with the conditions within these approvals, remain as significant site and corporate responsibilities. These licensing-construction integrated activities must now focus on identifying and resolving 'as-built' departures from the standardized design as assessed against the certified AP1000 technical and licensing basis. Within this paper, significant aspects of the AP1000 U.S. licensing will be discussed, including identifying systems and processes used in ensuring compliance while deploying the standardized design. Critical licensing steps, licensing deployment actions as plant construction progresses and defining the road forward to a successful completion of licensing actions will be addressed. (authors)« less

Use of lean and six sigma methodology to improve operating room efficiency in a high-volume tertiary-care academic medical center.

PubMed

Cima, Robert R; Brown, Michael J; Hebl, James R; Moore, Robin; Rogers, James C; Kollengode, Anantha; Amstutz, Gwendolyn J; Weisbrod, Cheryl A; Narr, Bradly J; Deschamps, Claude

2011-07-01

Operating rooms (ORs) are resource-intense and costly hospital units. Maximizing OR efficiency is essential to maintaining an economically viable institution. OR efficiency projects often focus on a limited number of ORs or cases. Efforts across an entire OR suite have not been reported. Lean and Six Sigma methodologies were developed in the manufacturing industry to increase efficiency by eliminating non-value-added steps. We applied Lean and Six Sigma methodologies across an entire surgical suite to improve efficiency. A multidisciplinary surgical process improvement team constructed a value stream map of the entire surgical process from the decision for surgery to discharge. Each process step was analyzed in 3 domains, ie, personnel, information processed, and time. Multidisciplinary teams addressed 5 work streams to increase value at each step: minimizing volume variation; streamlining the preoperative process; reducing nonoperative time; eliminating redundant information; and promoting employee engagement. Process improvements were implemented sequentially in surgical specialties. Key performance metrics were collected before and after implementation. Across 3 surgical specialties, process redesign resulted in substantial improvements in on-time starts and reduction in number of cases past 5 pm. Substantial gains were achieved in nonoperative time, staff overtime, and ORs saved. These changes resulted in substantial increases in margin/OR/day. Use of Lean and Six Sigma methodologies increased OR efficiency and financial performance across an entire operating suite. Process mapping, leadership support, staff engagement, and sharing performance metrics are keys to enhancing OR efficiency. The performance gains were substantial, sustainable, positive financially, and transferrable to other specialties. Copyright © 2011 American College of Surgeons. Published by Elsevier Inc. All rights reserved.

GWM-2005 - A Groundwater-Management Process for MODFLOW-2005 with Local Grid Refinement (LGR) Capability

USGS Publications Warehouse

Ahlfeld, David P.; Baker, Kristine M.; Barlow, Paul M.

2009-01-01

This report describes the Groundwater-Management (GWM) Process for MODFLOW-2005, the 2005 version of the U.S. Geological Survey modular three-dimensional groundwater model. GWM can solve a broad range of groundwater-management problems by combined use of simulation- and optimization-modeling techniques. These problems include limiting groundwater-level declines or streamflow depletions, managing groundwater withdrawals, and conjunctively using groundwater and surface-water resources. GWM was initially released for the 2000 version of MODFLOW. Several modifications and enhancements have been made to GWM since its initial release to increase the scope of the program's capabilities and to improve its operation and reporting of results. The new code, which is called GWM-2005, also was designed to support the local grid refinement capability of MODFLOW-2005. Local grid refinement allows for the simulation of one or more higher resolution local grids (referred to as child models) within a coarser grid parent model. Local grid refinement is often needed to improve simulation accuracy in regions where hydraulic gradients change substantially over short distances or in areas requiring detailed representation of aquifer heterogeneity. GWM-2005 can be used to formulate and solve groundwater-management problems that include components in both parent and child models. Although local grid refinement increases simulation accuracy, it can also substantially increase simulation run times.

Simple uncertainty propagation for early design phase aircraft sizing

NASA Astrophysics Data System (ADS)

Lenz, Annelise

Many designers and systems analysts are aware of the uncertainty inherent in their aircraft sizing studies; however, few incorporate methods to address and quantify this uncertainty. Many aircraft design studies use semi-empirical predictors based on a historical database and contain uncertainty -- a portion of which can be measured and quantified. In cases where historical information is not available, surrogate models built from higher-fidelity analyses often provide predictors for design studies where the computational cost of directly using the high-fidelity analyses is prohibitive. These surrogate models contain uncertainty, some of which is quantifiable. However, rather than quantifying this uncertainty, many designers merely include a safety factor or design margin in the constraints to account for the variability between the predicted and actual results. This can become problematic if a designer does not estimate the amount of variability correctly, which then can result in either an "over-designed" or "under-designed" aircraft. "Under-designed" and some "over-designed" aircraft will likely require design changes late in the process and will ultimately require more time and money to create; other "over-designed" aircraft concepts may not require design changes, but could end up being more costly than necessary. Including and propagating uncertainty early in the design phase so designers can quantify some of the errors in the predictors could help mitigate the extent of this additional cost. The method proposed here seeks to provide a systematic approach for characterizing a portion of the uncertainties that designers are aware of and propagating it throughout the design process in a procedure that is easy to understand and implement. Using Monte Carlo simulations that sample from quantified distributions will allow a systems analyst to use a carpet plot-like approach to make statements like: "The aircraft is 'P'% likely to weigh 'X' lbs or less, given the uncertainties quantified" without requiring the systems analyst to have substantial knowledge of probabilistic methods. A semi-empirical sizing study of a small single-engine aircraft serves as an example of an initial version of this simple uncertainty propagation. The same approach is also applied to a variable-fidelity concept study using a NASA-developed transonic Hybrid Wing Body aircraft.

26 CFR 1.460-2 - Long-term manufacturing contracts.

Code of Federal Regulations, 2011 CFR

2011-04-01

... specific customer, a taxpayer must consider the extent to which research, development, design, engineering... substantial amount of research, design, and engineering to produce, C determines that the equipment is a... produce, will be delivered to B in 2003. C determines that the research, design, engineering, retooling...

Beam delivery system with a non-digitized diffractive beam splitter for laser-drilling of silicon

NASA Astrophysics Data System (ADS)

Amako, J.; Fujii, E.

2016-02-01

We report a beam-delivery system consisting of a non-digitized diffractive beam splitter and a Fourier transform lens. The system is applied to the deep-drilling of silicon using a nanosecond pulse laser in the manufacture of inkjet printer heads. In this process, a circularly polarized pulse beam is divided into an array of uniform beams, which are then delivered precisely to the process points. To meet these requirements, the splitter was designed to be polarization-independent with an efficiency>95%. The optical elements were assembled so as to allow the fine tuning of the effective overall focal length by adjusting the wavefront curvature of the beam. Using the system, a beam alignment accuracy of<5 μm was achieved for a 12-mm-wide beam array and the throughput was substantially improved (10,000 points on a silicon wafer drilled in ~1 min). This beam-delivery scheme works for a variety of laser applications that require parallel processing.

A Combined Fabrication and Instrumentation Platform for Sample Preparation.

PubMed

Guckenberger, David J; Thomas, Peter C; Rothbauer, Jacob; LaVanway, Alex J; Anderson, Meghan; Gilson, Dan; Fawcett, Kevin; Berto, Tristan; Barrett, Kevin; Beebe, David J; Berry, Scott M

2014-06-01

While potentially powerful, access to molecular diagnostics is substantially limited in the developing world. Here we present an approach to reduced cost molecular diagnostic instrumentation that has the potential to empower developing world communities by reducing costs through streamlining the sample preparation process. In addition, this instrument is capable of producing its own consumable devices on demand, reducing reliance on assay suppliers. Furthermore, this instrument is designed with an "open" architecture, allowing users to visually observe the assay process and make modifications as necessary (as opposed to traditional "black box" systems). This open environment enables integration of microfluidic fabrication and viral RNA purification onto an easy-to-use modular system via the use of interchangeable trays. Here we employ this system to develop a protocol to fabricate microfluidic devices and then use these devices to isolate viral RNA from serum for the measurement of human immunodeficiency virus (HIV) viral load. Results obtained from this method show significantly reduced error compared with similar nonautomated sample preparation processes. © 2014 Society for Laboratory Automation and Screening.

Process for reducing series resistance of solar-cell metal-contact systems with a soldering-flux etchant

DOEpatents

Coyle, R.T.; Barrett, J.M.

1982-05-04

Disclosed is a process for substantially reducing the series resistance of a solar cell having a thick film metal contact assembly thereon while simultaneously removing oxide coatings from the surface of the assembly prior to applying solder therewith. The process includes applying a flux to the contact assembly and heating the cell for a period of time sufficient to substantially remove the series resistance associated with the assembly by etching the assembly with the flux while simultaneously removing metal oxides from said surface of said assembly.

Process for reducing series resistance of solar cell metal contact systems with a soldering flux etchant

DOEpatents

Coyle, R. T.; Barrett, Joy M.

1984-01-01

Disclosed is a process for substantially reducing the series resistance of a solar cell having a thick film metal contact assembly thereon while simultaneously removing oxide coatings from the surface of the assembly prior to applying solder therewith. The process includes applying a flux to the contact assembly and heating the cell for a period of time sufficient to substantially remove the series resistance associated with the assembly by etching the assembly with the flux while simultaneously removing metal oxides from said surface of said assembly.

Safety assessment in plant layout design using indexing approach: implementing inherent safety perspective. Part 2-Domino Hazard Index and case study.

PubMed

Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

2008-12-15

The design of layout plans requires adequate assessment tools for the quantification of safety performance. The general focus of the present work is to introduce an inherent safety perspective at different points of the layout design process. In particular, index approaches for safety assessment and decision-making in the early stages of layout design are developed and discussed in this two-part contribution. Part 1 (accompanying paper) of the current work presents an integrated index approach for safety assessment of early plant layout. In the present paper (Part 2), an index for evaluation of the hazard related to the potential of domino effects is developed. The index considers the actual consequences of possible escalation scenarios and scores or ranks the subsequent accident propagation potential. The effects of inherent and passive protection measures are also assessed. The result is a rapid quantification of domino hazard potential that can provide substantial support for choices in the early stages of layout design. Additionally, a case study concerning selection among various layout options is presented and analyzed. The case study demonstrates the use and applicability of the indices developed in both parts of the current work and highlights the value of introducing inherent safety features early in layout design.

Process for the removal of impurities from combustion fullerenes

DOEpatents

Alford, J. Michael; Bolskar, Robert

2005-08-02

The invention generally relates to purification of carbon nanomaterials, particularly fullerenes, by removal of PAHs and other hydrocarbon impurities. The inventive process involves extracting a sample containing carbon nanomaterials with a solvent in which the PAHs are substantially soluble but in which the carbon nanomaterials are not substantially soluble. The sample can be repeatedly or continuously extracted with one or more solvents to remove a greater amount of impurities. Preferred solvents include ethanol, diethyl ether, and acetone. The invention also provides a process for efficiently separating solvent extractable fullerenes from samples containing fullerenes and PAHs wherein the sample is extracted with a solvent in which both fullerenes and PAHs are substantially soluble and the sample extract then undergoes selective extraction to remove PAHs. Suitable solvents in which both fullerenes and PAHs are soluble include o-xylene, toluene, and o-dichlorobenzene. The purification process is capable of treating quantities of combustion soot in excess of one kilogram and can produce fullerenes or fullerenic soot of suitable purity for many applications.

Preparation of Effective Operating Manuals to Support Waste Management Plant Operator Training

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, S. R.

2003-02-25

Effective plant operating manuals used in a formal training program can make the difference between a successful operation and a failure. Once the plant process design and control strategies have been fixed, equipment has been ordered, and the plant is constructed, the only major variable affecting success is the capability of plant operating personnel. It is essential that the myriad details concerning plant operation are documented in comprehensive operating manuals suitable for training the non-technical personnel that will operate the plant. These manuals must cover the fundamental principles of each unit operation including how each operates, what process variables aremore » important, and the impact of each variable on the overall process. In addition, operators must know the process control strategies, process interlocks, how to respond to alarms, each of the detailed procedures required to start up and optimize the plant, and every control loop-including when it is appropriate to take manual control. More than anything else, operating mistakes during the start-up phase can lead to substantial delays in achieving design processing rates as well as to problems with government authorities if environmental permit limits are exceeded. The only way to assure return on plant investment is to ensure plant operators have the knowledge to properly run the plant from the outset. A comprehensive set of operating manuals specifically targeted toward plant operators and supervisors written by experienced operating personnel is the only effective way to provide the necessary information for formal start-up training.« less

Worklist handling in workflow-enabled radiological application systems

NASA Astrophysics Data System (ADS)

Wendler, Thomas; Meetz, Kirsten; Schmidt, Joachim; von Berg, Jens

2000-05-01

For the next generation integrated information systems for health care applications, more emphasis has to be put on systems which, by design, support the reduction of cost, the increase inefficiency and the improvement of the quality of services. A substantial contribution to this will be the modeling. optimization, automation and enactment of processes in health care institutions. One of the perceived key success factors for the system integration of processes will be the application of workflow management, with workflow management systems as key technology components. In this paper we address workflow management in radiology. We focus on an important aspect of workflow management, the generation and handling of worklists, which provide workflow participants automatically with work items that reflect tasks to be performed. The display of worklists and the functions associated with work items are the visible part for the end-users of an information system using a workflow management approach. Appropriate worklist design and implementation will influence user friendliness of a system and will largely influence work efficiency. Technically, in current imaging department information system environments (modality-PACS-RIS installations), a data-driven approach has been taken: Worklist -- if present at all -- are generated from filtered views on application data bases. In a future workflow-based approach, worklists will be generated by autonomous workflow services based on explicit process models and organizational models. This process-oriented approach will provide us with an integral view of entire health care processes or sub- processes. The paper describes the basic mechanisms of this approach and summarizes its benefits.

Ordinal optimization and its application to complex deterministic problems

NASA Astrophysics Data System (ADS)

Yang, Mike Shang-Yu

1998-10-01

We present in this thesis a new perspective to approach a general class of optimization problems characterized by large deterministic complexities. Many problems of real-world concerns today lack analyzable structures and almost always involve high level of difficulties and complexities in the evaluation process. Advances in computer technology allow us to build computer models to simulate the evaluation process through numerical means, but the burden of high complexities remains to tax the simulation with an exorbitant computing cost for each evaluation. Such a resource requirement makes local fine-tuning of a known design difficult under most circumstances, let alone global optimization. Kolmogorov equivalence of complexity and randomness in computation theory is introduced to resolve this difficulty by converting the complex deterministic model to a stochastic pseudo-model composed of a simple deterministic component and a white-noise like stochastic term. The resulting randomness is then dealt with by a noise-robust approach called Ordinal Optimization. Ordinal Optimization utilizes Goal Softening and Ordinal Comparison to achieve an efficient and quantifiable selection of designs in the initial search process. The approach is substantiated by a case study in the turbine blade manufacturing process. The problem involves the optimization of the manufacturing process of the integrally bladed rotor in the turbine engines of U.S. Air Force fighter jets. The intertwining interactions among the material, thermomechanical, and geometrical changes makes the current FEM approach prohibitively uneconomical in the optimization process. The generalized OO approach to complex deterministic problems is applied here with great success. Empirical results indicate a saving of nearly 95% in the computing cost.

Workflow for Criticality Assessment Applied in Biopharmaceutical Process Validation Stage 1.

PubMed

Zahel, Thomas; Marschall, Lukas; Abad, Sandra; Vasilieva, Elena; Maurer, Daniel; Mueller, Eric M; Murphy, Patrick; Natschläger, Thomas; Brocard, Cécile; Reinisch, Daniela; Sagmeister, Patrick; Herwig, Christoph

2017-10-12

Identification of critical process parameters that impact product quality is a central task during regulatory requested process validation. Commonly, this is done via design of experiments and identification of parameters significantly impacting product quality (rejection of the null hypothesis that the effect equals 0). However, parameters which show a large uncertainty and might result in an undesirable product quality limit critical to the product, may be missed. This might occur during the evaluation of experiments since residual/un-modelled variance in the experiments is larger than expected a priori. Estimation of such a risk is the task of the presented novel retrospective power analysis permutation test. This is evaluated using a data set for two unit operations established during characterization of a biopharmaceutical process in industry. The results show that, for one unit operation, the observed variance in the experiments is much larger than expected a priori, resulting in low power levels for all non-significant parameters. Moreover, we present a workflow of how to mitigate the risk associated with overlooked parameter effects. This enables a statistically sound identification of critical process parameters. The developed workflow will substantially support industry in delivering constant product quality, reduce process variance and increase patient safety.

The Socratic method in teaching medical ethics: potentials and limitations.

PubMed

Birnbacher, D

1999-01-01

The Socratic method has a long history in teaching philosophy and mathematics, marked by such names as Karl Weierstrass, Leonard Nelson and Gustav Heckmann. Its basic idea is to encourage the participants of a learning group (of pupils, students, or practitioners) to work on a conceptual, ethical or psychological problem by their own collective intellectual effort, without a textual basis and without substantial help from the teacher whose part it is mainly to enforce the rigid procedural rules designed to ensure a fruitful, diversified, open and consensus-oriented thought process. Several features of the Socratic procedure, especially in the canonical form given to it by Heckmann, are highly attractive for the teaching of medical ethics in small groups: the strategy of starting from relevant singular individual experiences, interpreting and cautiously generalizing them in a process of inter-subjective confrontation and confirmation, the duty of non-directivity on the part of the teacher in regard to the contents of the discussion, the necessity, on the part of the participants, to make explicit both their own thinking and the way they understand the thought of others, the strict separation of content level and meta level discussion and, not least, the wise use made of the emotional and motivational resources developing in the group process. Experience shows, however, that the canonical form of the Socratic group suffers from a number of drawbacks which may be overcome by loosening the rigidity of some of the rules. These concern mainly the injunction against substantial interventions on the part of the teacher and the insistence on consensus formation rooted in Leonard Nelson's Neo-Kantian Apriorism.

A knowledge-based design framework for airplane conceptual and preliminary design

NASA Astrophysics Data System (ADS)

Anemaat, Wilhelmus A. J.

The goal of work described herein is to develop the second generation of Advanced Aircraft Analysis (AAA) into an object-oriented structure which can be used in different environments. One such environment is the third generation of AAA with its own user interface, the other environment with the same AAA methods (i.e. the knowledge) is the AAA-AML program. AAA-AML automates the initial airplane design process using current AAA methods in combination with AMRaven methodologies for dependency tracking and knowledge management, using the TechnoSoft Adaptive Modeling Language (AML). This will lead to the following benefits: (1) Reduced design time: computer aided design methods can reduce design and development time and replace tedious hand calculations. (2) Better product through improved design: more alternative designs can be evaluated in the same time span, which can lead to improved quality. (3) Reduced design cost: due to less training and less calculation errors substantial savings in design time and related cost can be obtained. (4) Improved Efficiency: the design engineer can avoid technically correct but irrelevant calculations on incomplete or out of sync information, particularly if the process enables robust geometry earlier. Although numerous advancements in knowledge based design have been developed for detailed design, currently no such integrated knowledge based conceptual and preliminary airplane design system exists. The third generation AAA methods are tested over a ten year period on many different airplane designs. Using AAA methods will demonstrate significant time savings. The AAA-AML system will be exercised and tested using 27 existing airplanes ranging from single engine propeller, business jets, airliners, UAV's to fighters. Data for the varied sizing methods will be compared with AAA results, to validate these methods. One new design, a Light Sport Aircraft (LSA), will be developed as an exercise to use the tool for designing a new airplane. Using these tools will show an improvement in efficiency over using separate programs due to the automatic recalculation with any change of input data. The direct visual feedback of 3D geometry in the AAA-AML, will lead to quicker resolving of problems as opposed to conventional methods.

Re-designing the Mozambique vaccine supply chain to improve access to vaccines.

PubMed

Lee, Bruce Y; Haidari, Leila A; Prosser, Wendy; Connor, Diana L; Bechtel, Ruth; Dipuve, Amelia; Kassim, Hidayat; Khanlawia, Balbina; Brown, Shawn T

2016-09-22

Populations and routine childhood vaccine regimens have changed substantially since supply chains were designed in the 1980s, and introducing new vaccines during the "Decade of Vaccine" may exacerbate existing bottlenecks, further inhibiting the flow of all vaccines. Working with the Mozambique Ministry of Health, our team implemented a new process that integrated HERMES computational simulation modeling and on-the-ground implementers to evaluate and improve the Mozambique vaccine supply chain using a system-re-design that integrated new supply chain structures, information technology, equipment, personnel, and policies. The alternative system design raised vaccine availability (from 66% to 93% in Gaza; from 76% to 84% in Cabo Delgado) and reduced the logistics cost per dose administered (from $0.53 to $0.32 in Gaza; from $0.38 to $0.24 in Cabo Delgado) as compared to the multi-tiered system under the current EPI. The alternative system also produced higher availability at lower costs after new vaccine introductions. Since reviewing scenarios modeling deliveries every two months in the north of Gaza, the provincial directorate has decided to pilot this approach diverging from decades of policies dictating monthly deliveries. Re-design improved not only supply chain efficacy but also efficiency, important since resources to deliver vaccines are limited. The Mozambique experience and process can serve as a model for other countries during the Decade of Vaccines. For the Decade of Vaccines, getting vaccines at affordable prices to the market is not enough. Vaccines must reach the population to be successful. Copyright © 2016. Published by Elsevier Ltd.

Re-designing the Mozambique vaccine supply chain to improve access to vaccines

PubMed Central

Lee, Bruce Y.; Haidari, Leila A.; Prosser, Wendy; Connor, Diana L.; Bechtel, Ruth; Dipuve, Amelia; Kassim, Hidayat; Khanlawia, Balbina; Brown, Shawn T.

2017-01-01

Introduction Populations and routine childhood vaccine regimens have changed substantially since supply chains were designed in the 1980s, and introducing new vaccines during the “Decade of Vaccine” may exacerbate existing bottlenecks, further inhibiting the flow of all vaccines. Methods Working with the Mozambique Ministry of Health, our team implemented a new process that integrated HERMES computational simulation modeling and on-the-ground implementers to evaluate and improve the Mozambique vaccine supply chain using a system-re-design that integrated new supply chain structures, information technology, equipment, personnel, and policies. Results The alternative system design raised vaccine availability (from 66% to 93% in Gaza; from 76% to 84% in Cabo Delgado) and reduced the logistics cost per dose administered (from $0.53 to $0.32 in Gaza; from $0.38 to $0.24 in Cabo Delgado) as compared to the multi-tiered system under the current EPI. The alternative system also produced higher availability at lower costs after new vaccine introductions. Since reviewing scenarios modeling deliveries every two months in the north of Gaza, the provincial directorate has decided to pilot this approach diverging from decades of policies dictating monthly deliveries. Discussion Re-design improved not only supply chain efficacy but also efficiency, important since resources to deliver vaccines are limited. The Mozambique experience and process can serve as a model for other countries during the Decade of Vaccines. For the Decade of Vaccines, getting vaccines at affordable prices to the market is not enough. Vaccines must reach the population to be successful. PMID:27576077

Energy alternative for industry: the high-temperature gas-cooled reactor steamer

DOE Office of Scientific and Technical Information (OSTI.GOV)

McMain, A.T. Jr.; Blok, F.J.

1978-04-01

Large industrial complexes are faced with new requirements that will lead to a transition from such fluid fuels as natural gas and oil to such solid fuels as coal and uranium for supply of industrial energy. Power plants using these latter fuels will be of moderate size (800 to 1200 MW(thermal)) and will generally have the capability of co-generating electric power and process steam. A study has been made regarding use of the 840-MW(thermal) Fort St. Vrain high-temperature gas-cooled reactor (HTGR) design for industrial applications. The initial conceptual design (referred to as the HTGR Steamer) is substantially simplified relative tomore » Fort St. Vrain in that outlet helium and steam temperatures are lower and the reheat section is deleted from the steam generators. The Steamer has four independent steam generating loops producing a total of 277 kg/s (2.2 x 10/sup 6/ lb/h) of prime steam at 4.5 MPa/672 K (650 psia/750/sup 0/F). The unit co-generates 46 MW(electric) and provides process steam at 8.31 MPa/762 K(1200 psia/912/sup 0/F). The basic configuration and much of the equipment are retained from the Fort St. Vrain design. The system has inherent safety features important for industrial applications. These and other features indicate that the HTGR Steamer is an industrial energy option deserving additional evaluation. Subsequent work will focus on parallel design optimization and application studies.« less

78 FR 52363 - Endangered and Threatened Wildlife and Plants; Designation of Critical Habitat for the Diamond...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-22

... critical habitat rule will not have a significant economic impact on a substantial number of small entities... critical habitat as proposed will not have a significant economic impact on a substantial number of small... definition of small government'' is insufficient. They specifically mention a sentence on page ES-9 of the...

The spectral database Specchio: Data management, data sharing and initial processing of field spectrometer data within the Dimensions of Biodiversity project

NASA Astrophysics Data System (ADS)

Hueni, A.; Schweiger, A. K.

2015-12-01

Field spectrometry has substantially gained importance in vegetation ecology due to the increasing knowledge about causal ties between vegetation spectra and biochemical and structural plant traits. Additionally, worldwide databases enable the exchange of spectral and plant trait data and promote global research cooperation. This can be expected to further enhance the use of field spectrometers in ecological studies. However, the large amount of data collected during spectral field campaigns poses major challenges regarding data management, archiving and processing. The spectral database Specchio is designed to organize, manage, process and share spectral data and metadata. We provide an example for using Specchio based on leaf level spectra of prairie plant species collected during the 2015 field campaign of the Dimensions of Biodiversity research project, conducted at the Cedar Creek Long-Term Ecological Research site, in central Minnesota. We show how spectral data collections can be efficiently administered, organized and shared between distinct research groups and explore the capabilities of Specchio for data quality checks and initial processing steps.

Ergonomics, quality and continuous improvement--conceptual and empirical relationships in an industrial context.

PubMed

Eklund, J

1997-10-01

This paper reviews the literature comparing the fields of ergonomics and quality, mainly in an industrial context, including mutual influences, similarities and differences. Relationships between ergonomics and the factors: work conditions, product design, ISO 9000, continuous improvements and TQM are reviewed in relation to the consequence, application, and process domains. The definitions of ergonomics and quality overlap substantially. Quality deficiencies, human errors and ergonomics problems often have the same cause, which in many cases can be traced to the design of work, workplace and environment e.g. noise, light, postures, loads, pace and work content. In addition, the possibility of performing to a high standard at work is an important prerequisite for satisfaction and well-being. Contradictions between the two fields have been identified in the view of concepts such as standardization, reduction of variability and copying of best practice, requiring further research. The field of quality would gain by incorporating ergonomics knowledge, especially in the areas of work design and human capability, since these factors are decisive for human performance and also therefore the performance of the systems involved. The field of ergonomics, on the other hand, would benefit from developing a stronger emphasis on methodologies and structures for improvement processes, including a clearer link with leadership and company strategies. Just as important is a further development of practicable participative ergonomics methods and tools for use at workplaces by the workers themselves, in order to integrate the top-down and the bottom-up processes and achieve better impact. Using participative processes for problem-solving and continuous improvement, focusing ergonomics and quality jointly has a great potential for improving working conditions and quality results simultaneously, and satisfying most of the interested parties.

Low Cost Chemical Feedstocks Using an Improved and Energy Efficient Natural Gas Liquid (NGL) Removal Process, Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyer, Howard, S.; Lu, Yingzhong

The overall objective of this project is to develop a new low-cost and energy efficient Natural Gas Liquid (NGL) recovery process - through a combination of theoretical, bench-scale and pilot-scale testing - so that it could be offered to the natural gas industry for commercialization. The new process, known as the IROA process, is based on U.S. patent No. 6,553,784, which if commercialized, has the potential of achieving substantial energy savings compared to currently used cryogenic technology. When successfully developed, this technology will benefit the petrochemical industry, which uses NGL as feedstocks, and will also benefit other chemical industries thatmore » utilize gas-liquid separation and distillation under similar operating conditions. Specific goals and objectives of the overall program include: (i) collecting relevant physical property and Vapor Liquid Equilibrium (VLE) data for the design and evaluation of the new technology, (ii) solving critical R&D issues including the identification of suitable dehydration and NGL absorbing solvents, inhibiting corrosion, and specifying proper packing structure and materials, (iii) designing, construction and operation of bench and pilot-scale units to verify design performance, (iv) computer simulation of the process using commercial software simulation platforms such as Aspen-Plus and HYSYS, and (v) preparation of a commercialization plan and identification of industrial partners that are interested in utilizing the new technology. NGL is a collective term for C2+ hydrocarbons present in the natural gas. Historically, the commercial value of the separated NGL components has been greater than the thermal value of these liquids in the gas. The revenue derived from extracting NGLs is crucial to ensuring the overall profitability of the domestic natural gas production industry and therefore of ensuring a secure and reliable supply in the 48 contiguous states. However, rising natural gas prices have dramatically reduced the economic incentive to extract NGLs from domestically produced natural gas. Successful gas processors will be those who adopt technologies that are less energy intensive, have lower capital and operating costs and offer the flexibility to tailor the plant performance to maximize product revenue as market conditions change, while maintaining overall system efficiency. Presently, cryogenic turbo-expander technology is the dominant NGL recovery process and it is used throughout the world. This process is known to be highly energy intensive, as substantial energy is required to recompress the processed gas back to pipeline pressure. The purpose of this project is to develop a new NGL separation process that is flexible in terms of ethane rejection and can reduce energy consumption by 20-30% from current levels, particularly for ethane recoveries of less than 70%. The new process integrates the dehydration of the raw natural gas stream and the removal of NGLs in such a way that heat recovery is maximized and pressure losses are minimized so that high-value equipment such as the compressor, turbo-expander, and a separate dehydration unit are not required. GTI completed a techno-economic evaluation of the new process based on an Aspen-HYSYS simulation model. The evaluation incorporated purchased equipment cost estimates obtained from equipment suppliers and two different commercial software packages; namely, Aspen-Icarus and Preliminary Design and Quoting Service (PDQ$). For a 100 MMscfd gas processing plant, the annualized capital cost for the new technology was found to be about 10% lower than that of conventional technology for C2 recovery above 70% and about 40% lower than that of conventional technology for C2 recovery below 50%. It was also found that at around 40-50% C2 recovery (which is economically justifiable at the current natural gas prices), the energy cost to recover NGL using the new technology is about 50% of that of conventional cryogenic technology.« less

Ferrosilicon smelting in a direct current furnace

DOEpatents

Dosaj, Vishu D.; May, James B.

1992-12-29

The present invention is a process for smelting ferrosilicon alloy. The process comprises adding a carbon source and tailings comprising oxides of silicon and iron to a substantially closed furnace. Heat is supplied to the furnace by striking a direct current arc between a cathode electrode and an anode functional hearth. In a preferred embodiment of the present invention, the cathode electrode is hollow and feed to the substantially closed furnace is through the hollow electrode.

Pyrolysis process and apparatus

DOEpatents

Lee, Chang-Kuei

1983-01-01

This invention discloses a process and apparatus for pyrolyzing particulate coal by heating with a particulate solid heating media in a transport reactor. The invention tends to dampen fluctuations in the flow of heating media upstream of the pyrolysis zone, and by so doing forms a substantially continuous and substantially uniform annular column of heating media flowing downwardly along the inside diameter of the reactor. The invention is particularly useful for bituminous or agglomerative type coals.

Optimizing an immersion ESL curriculum using analytic hierarchy process.

PubMed

Tang, Hui-Wen Vivian

2011-11-01

The main purpose of this study is to fill a substantial knowledge gap regarding reaching a uniform group decision in English curriculum design and planning. A comprehensive content-based course criterion model extracted from existing literature and expert opinions was developed. Analytical hierarchy process (AHP) was used to identify the relative importance of course criteria for the purpose of tailoring an optimal one-week immersion English as a second language (ESL) curriculum for elementary school students in a suburban county of Taiwan. The hierarchy model and AHP analysis utilized in the present study will be useful for resolving several important multi-criteria decision-making issues in planning and evaluating ESL programs. This study also offers valuable insights and provides a basis for further research in customizing ESL curriculum models for different student populations with distinct learning needs, goals, and socioeconomic backgrounds. Copyright © 2011 Elsevier Ltd. All rights reserved.

Synthesis of nanoparticles using ethanol

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Jia Xu

The present disclosure relates to methods for producing nanoparticles. The nanoparticles may be made using ethanol as the solvent and the reductant to fabricate noble-metal nanoparticles with a narrow particle size distributions, and to coat a thin metal shell on other metal cores. With or without carbon supports, particle size is controlled by fine-tuning the reduction power of ethanol, by adjusting the temperature, and by adding an alkaline solution during syntheses. The thickness of the added or coated metal shell can be varied easily from sub-monolayer to multiple layers in a seed-mediated growth process. The entire synthesis of designed core-shellmore » catalysts can be completed using metal salts as the precursors with more than 98% yield; and, substantially no cleaning processes are necessary apart from simple rinsing. Accordingly, this method is considered to be a "green" chemistry method.« less

On the Injection Molding Processing Parameters of HDPE-TiO2 Nanocomposites

PubMed Central

Mourad, Abdel-Hamid I.; Mozumder, Mohammad Sayem; Mairpady, Anusha; Pervez, Hifsa; Kannuri, Uma Maheshwara

2017-01-01

In recent years, the development and use of polymeric nanocomposites in creating advanced materials has expanded exponentially. A substantial amount of research has been done in order to design polymeric nanocomposites in a safe and efficient manner. In the present study, the impact of processing parameters, such as, barrel temperature, and residence time on the mechanical and thermal properties of high density polyethylene (HDPE)-TiO2 nanocomposites were investigated. Additionally, scanning electron microscopy and X-ray diffraction spectroscopy were used to analyze the dispersion, location, and phase morphology of TiO2 on the HDPE matrix. Mechanical tests revealed that tensile strength of the fabricated HDPE-TiO2 nanocomposites ranged between 22.53 and 26.30 MPa, while the Young’s modulus showed a consistent increase as the barrel temperature increased from 150 °C to 300 °C. Moreover, the thermal stability decreased as the barrel temperature increased. PMID:28772444

On the Injection Molding Processing Parameters of HDPE-TiO₂ Nanocomposites.

PubMed

Mourad, Abdel-Hamid I; Mozumder, Mohammad Sayem; Mairpady, Anusha; Pervez, Hifsa; Kannuri, Uma Maheshwara

2017-01-20

In recent years, the development and use of polymeric nanocomposites in creating advanced materials has expanded exponentially. A substantial amount of research has been done in order to design polymeric nanocomposites in a safe and efficient manner. In the present study, the impact of processing parameters, such as, barrel temperature, and residence time on the mechanical and thermal properties of high density polyethylene (HDPE)-TiO₂ nanocomposites were investigated. Additionally, scanning electron microscopy and X-ray diffraction spectroscopy were used to analyze the dispersion, location, and phase morphology of TiO₂ on the HDPE matrix. Mechanical tests revealed that tensile strength of the fabricated HDPE-TiO₂ nanocomposites ranged between 22.53 and 26.30 MPa, while the Young's modulus showed a consistent increase as the barrel temperature increased from 150 °C to 300 °C. Moreover, the thermal stability decreased as the barrel temperature increased.

Low toxicity high temperature PMR polyimide

NASA Technical Reports Server (NTRS)

Pater, Ruth H. (Inventor)

1992-01-01

In-situ polymerization of monomer reactants (PMR) type polyimides constitute an important class of ultra high performance composite matrix resins. PMR-15 is the best known and most widely used PMR polyimide. An object of the present invention is to provide a substantially improved high temperature PMR-15 system that exhibits better processability, toughness, and thermo-oxidative stability than PMR-15, as well as having a low toxicity. Another object is to provide new PMR polyimides that are useful as adhesives, moldings, and composite matrices. By the present invention, a new PMR polyimide comprises a mixture of the following compounds: 3,4'-oxydianiline (3,4'-ODA), NE, and BTDE which are then treated with heat. This PMR was designated LaRC-RP46 and has a broader processing window, better reproducibility of high quality composite parts, better elevated temperature mechanical properties, and higher retention of mechanical properties at an elevated temperature, particularly, at 371 C.

Conductivity and power factor enhancement of n-type semiconducting polymers using sodium silica gel dopant

NASA Astrophysics Data System (ADS)

Madan, Deepa; Zhao, Xingang; Ireland, Robert M.; Xiao, Derek; Katz, Howard E.

2017-08-01

This work demonstrates the use of sodium silica gel (Na-SG) particles as a reducing agent for n-type conjugated polymers to improve the conductivity and thermoelectric properties. Substantial increase in the electrical conductivity (σ, from 10-7 to 10-3 S/cm in air) was observed in two naphthalenetetracarboxylic diimide solution-processable n-type polymers, one of which was designed and synthesized in our lab. Systematic investigations of electrical conductivity were done by varying the weight percentage of Na-SG in the polymers. Additional evidence for the reduction process was obtained from electron spin resonance spectroscopy and control experiments involving nonreducing silica particles and non-electron-accepting polystyrene. The Seebeck coefficient S of the highest conductivity sample was measured and found to be in agreement with an empirical model. All the electrical conductivity and Seebeck coefficients measurements were performed in ambient atmosphere.

Subcritical ethanol extraction of flavonoids from Moringa oleifera leaf and evaluation of antioxidant activity.

PubMed

Wang, Yongqiang; Gao, Yujie; Ding, Hui; Liu, Shejiang; Han, Xu; Gui, Jianzhou; Liu, Dan

2017-03-01

A large-scale process to extract flavonoids from Moringa oleifera leaf by subcritical ethanol was developed and HPLC-MS analysis was conducted to qualitatively identify the compounds in the extracts. To optimize the effects of process parameters on the yield of flavonoids, a Box-Behnken design combined with response surface methodology was conducted in the present work. The results indicated that the highest extraction yield of flavonoids by subcritical ethanol extraction could reach 2.60% using 70% ethanol at 126.6°C for 2.05h extraction. Under the optimized conditions, flavonoids yield was substantially improved by 26.7% compared with the traditional ethanol reflux method while the extraction time was only 2h, and obvious energy saving was observed. FRAP and DPPH assays showed that the extracts had strong antioxidant and free radical scavenging activities. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermoelectrically cooled water trap

DOEpatents

Micheels, Ronald H [Concord, MA

2006-02-21

A water trap system based on a thermoelectric cooling device is employed to remove a major fraction of the water from air samples, prior to analysis of these samples for chemical composition, by a variety of analytical techniques where water vapor interferes with the measurement process. These analytical techniques include infrared spectroscopy, mass spectrometry, ion mobility spectrometry and gas chromatography. The thermoelectric system for trapping water present in air samples can substantially improve detection sensitivity in these analytical techniques when it is necessary to measure trace analytes with concentrations in the ppm (parts per million) or ppb (parts per billion) partial pressure range. The thermoelectric trap design is compact and amenable to use in a portable gas monitoring instrumentation.

Lunar-derived titanium alloys for hydrogen storage

NASA Technical Reports Server (NTRS)

Love, S.; Hertzberg, A.; Woodcock, G.

1992-01-01

Hydrogen gas, which plays an important role in many projected lunar power systems and industrial processes, can be stored in metallic titanium and in certain titanium alloys as an interstitial hydride compound. Storing and retrieving hydrogen with titanium-iron alloy requires substantially less energy investment than storage by liquefaction. Metal hydride storage systems can be designed to operate at a wide range of temperatures and pressures. A few such systems have been developed for terrestrial applications. A drawback of metal hydride storage for lunar applications is the system's large mass per mole of hydrogen stored, which rules out transporting it from earth. The transportation problem can be solved by using native lunar materials, which are rich in titanium and iron.

Three steps to writing adaptive study protocols in the early phase clinical development of new medicines

PubMed Central

2014-01-01

This article attempts to define terminology and to describe a process for writing adaptive, early phase study protocols which are transparent, self-intuitive and uniform. It provides a step by step guide, giving templates from projects which received regulatory authorisation and were successfully performed in the UK. During adaptive studies evolving data is used to modify the trial design and conduct within the protocol-defined remit. Adaptations within that remit are documented using non-substantial protocol amendments which do not require regulatory or ethical review. This concept is efficient in gathering relevant data in exploratory early phase studies, ethical and time- and cost-effective. PMID:24980283

The role of language in mathematical development: evidence from children with specific language impairments.

PubMed

Donlan, Chris; Cowan, Richard; Newton, Elizabeth J; Lloyd, Delyth

2007-04-01

A sample (n=48) of eight-year-olds with specific language impairments is compared with age-matched (n=55) and language matched controls (n=55) on a range of tasks designed to test the interdependence of language and mathematical development. Performance across tasks varies substantially in the SLI group, showing profound deficits in production of the count word sequence and basic calculation and significant deficits in understanding of the place-value principle in Hindu-Arabic notation. Only in understanding of arithmetic principles does SLI performance approximate that of age-matched-controls, indicating that principled understanding can develop even where number sequence production and other aspects of number processing are severely compromised.

International migration, "middle classness" and the state.

PubMed

Grant, G S

1995-01-01

"This paper examines the issues of who is likely to migrate and why, and what happens when people migrate, by viewing the migratory process as a strategy formulated and implemented by networks of kin for culturally surviving the redefinitions of contemporary political systems within the context of the capitalist world economy. Specifically the argument presented is that people move across the juridical boundaries of contemporary nation-states as part of household strategies designed to maintain membership in a specific social stratum. For a substantial number this social stratum is a middle class. Self-identification with a social stratum, in other words, takes precedence over self-identification with, and commitments to, nation, region or ethnic group." excerpt

Quantum Memristors with Superconducting Circuits

DOE PAGES

Salmilehto, J.; Deppe, F.; Di Ventra, M.; ...

2017-02-14

Memristors are resistive elements retaining information of their past dynamics. They have garnered substantial interest due to their potential for representing a paradigm change in electronics, information processing and unconventional computing. Given the advent of quantum technologies, a design for a quantum memristor with superconducting circuits may be envisaged. Along these lines, we introduce such a quantum device whose memristive behavior arises from quasiparticle-induced tunneling when supercurrents are cancelled. Here in this paper, for realistic parameters, we find that the relevant hysteretic behavior may be observed using current state-of-the-art measurements of the phase-driven tunneling current. Finally, we develop suitable methodsmore » to quantify memory retention in the system.« less

Critical considerations when planning experimental in vivo studies in dental traumatology.

PubMed

Andreasen, Jens O; Andersson, Lars

2011-08-01

In vivo studies are sometimes needed to understand healing processes after trauma. For several reasons, not the least ethical, such studies have to be carefully planned and important considerations have to be taken into account about suitability of the experimental model, sample size and optimizing the accuracy of the analysis. Several manuscripts of in vivo studies are submitted for publication to Dental Traumatology and rejected because of inadequate design, methodology or insufficient documentation of the results. The authors have substantial experience in experimental in vivo studies of tissue healing in dental traumatology and share their knowledge regarding critical considerations when planning experimental in vivo studies. © 2011 John Wiley & Sons A/S.

An integrated CMOS bio-potential amplifier with a feed-forward DC cancellation topology.

PubMed

Parthasarathy, Jayant; Erdman, Arthur G; Redish, Aaron D; Ziaie, Babak

2006-01-01

This paper describes a novel technique to realize an integrated CMOS bio-potential amplifier with a feedforward DC cancellation topology. The amplifier is designed to provide substantial DC cancellation even while amplifying very low frequency signals. More than 80 dB offset rejection ratio is achieved without any external capacitors. The cancellation scheme is robust against process and temperature variations. The amplifier is fabricated through MOSIS AMI 1.5 microm technology (0.05 mm2 area). Measurement results show a gain of 43.5 dB in the pass band (<1 mHz-5 KHz), an input referred noise of 3.66 microVrms, and a current consumption of 22 microA.

Sewage-treatment under substantial load variations in winter tourism areas--a full case study.

PubMed

Winkler, S; Matsché, N; Gamperer, T; Dum, M

2004-01-01

The sewage-load variations in winter tourism areas are characterized by sudden increases--in the range of a factor two to three--within only a few days at the start and the end of the tourist season, especially at Christmas. The sudden load increases occur during periods of low wastewater temperatures, which is an additional demanding factor with respect to nitrogen removal. A full case study was carried out at WWTP Saalfelden, which is located near one of Austria's largest skiing resorts. The plant is designed for 80,000 PE and built according to the HYBRID-concept, which is a special two stage activated sludge process for extensive nutrient removal.

Virtual Screening of Receptor Sites for Molecularly Imprinted Polymers.

PubMed

Bates, Ferdia; Cela-Pérez, María Concepción; Karim, Kal; Piletsky, Sergey; López-Vilariño, José Manuel

2016-08-01

Molecularly Imprinted Polymers (MIPs) are highly advantageous in the field of analytical chemistry. However, interference from secondary molecules can also impede capture of a target by a MIP receptor. This greatly complicates the design process and often requires extensive laboratory screening which is time consuming, costly, and creates substantial waste products. Herein, is presented a new technique for screening of "virtually imprinted receptors" for rebinding of the molecular template as well as secondary structures, correlating the virtual predictions with experimentally acquired data in three case studies. This novel technique is particularly applicable to the evaluation and prediction of MIP receptor specificity and efficiency in complex aqueous systems. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Conceptual Design of a Nano-Networking Device

PubMed Central

Canovas-Carrasco, Sebastian; Garcia-Sanchez, Antonio-Javier; Garcia-Sanchez, Felipe; Garcia-Haro, Joan

2016-01-01

Nanotechnology is an emerging scientific area whose advances, among many others, have a positive direct impact on the miniaturization of electronics. This unique technology enables the possibility to design and build electronic components as well as complete devices (called nanomachines or nanodevices) at the nano scale. A nanodevice is expected to be an essential element able to operate in a nanonetwork, where a huge number of them would coordinate to acquire data, process the information gathered, and wirelessly transmit those data to end-points providing innovative services in many key scenarios, such as the human body or the environment. This paper is aimed at studying the feasibility of this type of device by carefully examining their main component parts, namely the nanoprocessor, nanomemory, nanoantenna, and nanogenerator. To this end, a thorough state-of-the-art review is conveyed to discuss, substantiate, and select the most suitable current technology (commercial or pre-commercial) for each component. Then, we further contribute by developing a complete conceptual nanodevice layout taking into consideration its ultra-small size (similar to a blood cell) and its very restricted capabilities (e.g., processing, memory storage, telecommunication, and energy management). The required resources as well as the power consumption are realistically estimated. PMID:27973430

The JINR Tier1 Site Simulation for Research and Development Purposes

NASA Astrophysics Data System (ADS)

Korenkov, V.; Nechaevskiy, A.; Ososkov, G.; Pryahina, D.; Trofimov, V.; Uzhinskiy, A.; Voytishin, N.

2016-02-01

Distributed complex computing systems for data storage and processing are in common use in the majority of modern scientific centers. The design of such systems is usually based on recommendations obtained via a preliminary simulated model used and executed only once. However big experiments last for years and decades, and the development of their computing system is going on, not only quantitatively but also qualitatively. Even with the substantial efforts invested in the design phase to understand the systems configuration, it would be hard enough to develop a system without additional research of its future evolution. The developers and operators face the problem of the system behaviour predicting after the planned modifications. A system for grid and cloud services simulation is developed at LIT (JINR, Dubna). This simulation system is focused on improving the effciency of the grid/cloud structures development by using the work quality indicators of some real system. The development of such kind of software is very important for making a new grid/cloud infrastructure for such big scientific experiments like the JINR Tier1 site for WLCG. The simulation of some processes of the Tier1 site is considered as an example of our application approach.

Conceptual Design of a Nano-Networking Device.

PubMed

Canovas-Carrasco, Sebastian; Garcia-Sanchez, Antonio-Javier; Garcia-Sanchez, Felipe; Garcia-Haro, Joan

2016-12-11

Nanotechnology is an emerging scientific area whose advances, among many others, have a positive direct impact on the miniaturization of electronics. This unique technology enables the possibility to design and build electronic components as well as complete devices (called nanomachines or nanodevices) at the nano scale. A nanodevice is expected to be an essential element able to operate in a nanonetwork, where a huge number of them would coordinate to acquire data, process the information gathered, and wirelessly transmit those data to end-points providing innovative services in many key scenarios, such as the human body or the environment. This paper is aimed at studying the feasibility of this type of device by carefully examining their main component parts, namely the nanoprocessor, nanomemory, nanoantenna, and nanogenerator. To this end, a thorough state-of-the-art review is conveyed to discuss, substantiate, and select the most suitable current technology (commercial or pre-commercial) for each component. Then, we further contribute by developing a complete conceptual nanodevice layout taking into consideration its ultra-small size (similar to a blood cell) and its very restricted capabilities (e.g., processing, memory storage, telecommunication, and energy management). The required resources as well as the power consumption are realistically estimated.

Review and Prospect of BIM Policy in China

NASA Astrophysics Data System (ADS)

Liu, Bingsheng; Wang, Min; Zhang, Yutao; Liu, Rui; Wang, Anmin

2017-10-01

In the process of architectural design, construction, operation and maintenance, the problem of inefficiency and inaccuracy in information application and exchange has caused substantial waste of resources and risk in construction industry. Building Information Management provides an opportunity to address the issue. Building information modelling (BIM) has been increasingly applied in design, construction and other information management in China as its important role in reducing engineering changes, improving engineering quality, shortening project duration, saving project cost, enhancing information sharing among the participants many others. As an integration of process and product, its development and implementation need government regulation to enhance its applications effect and standardize its adoption and implementation. Especially, the government guidance affects the application and development of new technology to a great extent in China. However, relevant policy development falls behind the rapid development of its application in practice in China, which has led to many problems in construction practice. In order to develop effective BIM policy for China, this paper conducted a comprehensive review about existing BIM policy in China by analysing its status and problems, comparing it with the corresponding policy in developed countries such as the USA and UK. The expected policy development direction is also discussed and proposed.

Concentric Split Flow Filter

NASA Technical Reports Server (NTRS)

Stapleton, Thomas J. (Inventor)

2015-01-01

A concentric split flow filter may be configured to remove odor and/or bacteria from pumped air used to collect urine and fecal waste products. For instance, filter may be designed to effectively fill the volume that was previously considered wasted surrounding the transport tube of a waste management system. The concentric split flow filter may be configured to split the air flow, with substantially half of the air flow to be treated traveling through a first bed of filter media and substantially the other half of the air flow to be treated traveling through the second bed of filter media. This split flow design reduces the air velocity by 50%. In this way, the pressure drop of filter may be reduced by as much as a factor of 4 as compare to the conventional design.

Design and fabrication of a micron scale free-standing specimen for uniaxial micro-tensile tests

NASA Astrophysics Data System (ADS)

Tang, Jun; Wang, Hong; Li, Shi Chen; Liu, Rui; Mao, Sheng Ping; Li, Xue Ping; Zhang, Cong Chun; Ding, Guifu

2009-10-01

This paper presents a novel design and fabrication of test chips with a nickel free-standing specimen for the micro uniaxial tensile test. To fabricate test chips on the quartz substrate significantly reduces the fabrication time, minimizes the number of steps and eliminates the effect of the wet anisotropic etching process on mechanical properties. The test chip can be gripped tightly to the test machine and aligned accurately in the pulling direction; furthermore, the approximately straight design of the specimen rather than the traditional dog-bone structure enables the strain be directly measured by a displacement sensor. Both finite-element method (FEM) analysis and experimental results indicate the reliability of the new design. The test chip can also be extended to other materials. The experimental measured Young's modulus of a thin nickel film and the ultimate tensile strength are approximately 94.5 Gpa and 1.76 Gpa, respectively. The results were substantially supported by the experiment on larger gauge specimens by a commercial dynamic mechanical analysis (DMA) instrument. These specimens were electroplated under the same conditions. The low Young's modulus and the high ultimate tensile strength might be explained by the fine grain in the electroplated structure.

Results From a Channel Restoration Project: Hydraulic Design Considerations

USGS Publications Warehouse

Karle, K.F.; Densmore, R.V.; ,

2001-01-01

Techniques for the hydraulic restoration of placer-mined streams and floodplains were developed in Denali National Park and Preserve, Alaska. The two-year study at Glen Creek focused on a design of stream and floodplain geometry using hydraulic capacity and shear stress equations. Slope and sinuosity values were based on regional relationships. Design requirements included a channel capacity for a bankfull discharge and a floodplain capacity for a 1.5- to 100-year discharge. Several bio-engineering techniques using alder and willow, including anchored brush bars, streambank hedge layering, seedlings, and cuttings, were tested to dissipate floodwater energy and encourage sediment deposition until natural revegetation stabilized the new floodplains. Permanently monumented cross-sections installed throughout the project site were surveyed every one to three years. Nine years after the project began, a summer flood caused substantial damage to the channel form, including a change in width/depth ratio, slope, and thalweg location. Many of the alder brush bars were heavily damaged or destroyed, resulting in significant bank erosion. This paper reviews the original hydraulic design process, and describes changes to the channel and floodplain geometry over time, based on nine years of cross-section surveys.

An informatics model for guiding assembly of telemicrobiology workstations for malaria collaborative diagnostics using commodity products and open-source software.

PubMed

Suhanic, West; Crandall, Ian; Pennefather, Peter

2009-07-17

Deficits in clinical microbiology infrastructure exacerbate global infectious disease burdens. This paper examines how commodity computation, communication, and measurement products combined with open-source analysis and communication applications can be incorporated into laboratory medicine microbiology protocols. Those commodity components are all now sourceable globally. An informatics model is presented for guiding the use of low-cost commodity components and free software in the assembly of clinically useful and usable telemicrobiology workstations. The model incorporates two general principles: 1) collaborative diagnostics, where free and open communication and networking applications are used to link distributed collaborators for reciprocal assistance in organizing and interpreting digital diagnostic data; and 2) commodity engineering, which leverages globally available consumer electronics and open-source informatics applications, to build generic open systems that measure needed information in ways substantially equivalent to more complex proprietary systems. Routine microscopic examination of Giemsa and fluorescently stained blood smears for diagnosing malaria is used as an example to validate the model. The model is used as a constraint-based guide for the design, assembly, and testing of a functioning, open, and commoditized telemicroscopy system that supports distributed acquisition, exploration, analysis, interpretation, and reporting of digital microscopy images of stained malarial blood smears while also supporting remote diagnostic tracking, quality assessment and diagnostic process development. The open telemicroscopy workstation design and use-process described here can address clinical microbiology infrastructure deficits in an economically sound and sustainable manner. It can boost capacity to deal with comprehensive measurement of disease and care outcomes in individuals and groups in a distributed and collaborative fashion. The workstation enables local control over the creation and use of diagnostic data, while allowing for remote collaborative support of diagnostic data interpretation and tracking. It can enable global pooling of malaria disease information and the development of open, participatory, and adaptable laboratory medicine practices. The informatic model highlights how the larger issue of access to generic commoditized measurement, information processing, and communication technology in both high- and low-income countries can enable diagnostic services that are much less expensive, but substantially equivalent to those currently in use in high-income countries.

14 CFR 21.191 - Experimental certificates.

Code of Federal Regulations, 2014 CFR

2014-01-01

... aircraft design concepts, new aircraft equipment, new aircraft installations, new aircraft operating... compliance for issuance of type and supplemental type certificates, flights to substantiate major design... from racing events. (f) Market surveys. Use of aircraft for purposes of conducting market surveys...

Texas M-E flexible pavement design system: literature review and proposed framework.

DOT National Transportation Integrated Search

2012-04-01

Recent developments over last several decades have offered an opportunity for more rational and rigorous pavement design procedures. Substantial work has already been completed in Texas, nationally, and internationally, in all aspects of modeling, ma...

14 CFR 21.191 - Experimental certificates.

Code of Federal Regulations, 2012 CFR

2012-01-01

.... Experimental certificates are issued for the following purposes: (a) Research and development. Testing new aircraft design concepts, new aircraft equipment, new aircraft installations, new aircraft operating... compliance for issuance of type and supplemental type certificates, flights to substantiate major design...

14 CFR 21.191 - Experimental certificates.

Code of Federal Regulations, 2011 CFR

2011-01-01

.... Experimental certificates are issued for the following purposes: (a) Research and development. Testing new aircraft design concepts, new aircraft equipment, new aircraft installations, new aircraft operating... compliance for issuance of type and supplemental type certificates, flights to substantiate major design...

14 CFR 21.191 - Experimental certificates.

Code of Federal Regulations, 2013 CFR

2013-01-01

.... Experimental certificates are issued for the following purposes: (a) Research and development. Testing new aircraft design concepts, new aircraft equipment, new aircraft installations, new aircraft operating... compliance for issuance of type and supplemental type certificates, flights to substantiate major design...

14 CFR 21.191 - Experimental certificates.

Code of Federal Regulations, 2010 CFR

2010-01-01

.... Experimental certificates are issued for the following purposes: (a) Research and development. Testing new aircraft design concepts, new aircraft equipment, new aircraft installations, new aircraft operating... compliance for issuance of type and supplemental type certificates, flights to substantiate major design...

Robust optimization of a tandem grating solar thermal absorber

NASA Astrophysics Data System (ADS)

Choi, Jongin; Kim, Mingeon; Kang, Kyeonghwan; Lee, Ikjin; Lee, Bong Jae

2018-04-01

Ideal solar thermal absorbers need to have a high value of the spectral absorptance in the broad solar spectrum to utilize the solar radiation effectively. Majority of recent studies about solar thermal absorbers focus on achieving nearly perfect absorption using nanostructures, whose characteristic dimension is smaller than the wavelength of sunlight. However, precise fabrication of such nanostructures is not easy in reality; that is, unavoidable errors always occur to some extent in the dimension of fabricated nanostructures, causing an undesirable deviation of the absorption performance between the designed structure and the actually fabricated one. In order to minimize the variation in the solar absorptance due to the fabrication error, the robust optimization can be performed during the design process. However, the optimization of solar thermal absorber considering all design variables often requires tremendous computational costs to find an optimum combination of design variables with the robustness as well as the high performance. To achieve this goal, we apply the robust optimization using the Kriging method and the genetic algorithm for designing a tandem grating solar absorber. By constructing a surrogate model through the Kriging method, computational cost can be substantially reduced because exact calculation of the performance for every combination of variables is not necessary. Using the surrogate model and the genetic algorithm, we successfully design an effective solar thermal absorber exhibiting a low-level of performance degradation due to the fabrication uncertainty of design variables.

Knowledge based system and decision making methodologies in materials selection for aircraft cabin metallic structures

NASA Astrophysics Data System (ADS)

Adhikari, Pashupati Raj

Materials selection processes have been the most important aspects in product design and development. Knowledge-based system (KBS) and some of the methodologies used in the materials selection for the design of aircraft cabin metallic structures are discussed. Overall aircraft weight reduction means substantially less fuel consumption. Part of the solution to this problem is to find a way to reduce overall weight of metallic structures inside the cabin. Among various methodologies of materials selection using Multi Criterion Decision Making (MCDM) techniques, a few of them are demonstrated with examples and the results are compared with those obtained using Ashby's approach in materials selection. Pre-defined constraint values, mainly mechanical properties, are employed as relevant attributes in the process. Aluminum alloys with high strength-to-weight ratio have been second-to-none in most of the aircraft parts manufacturing. Magnesium alloys that are much lighter in weight as alternatives to the Al-alloys currently in use in the structures are tested using the methodologies and ranked results are compared. Each material attribute considered in the design are categorized as benefit and non-benefit attribute. Using Ashby's approach, material indices that are required to be maximized for an optimum performance are determined, and materials are ranked based on the average of consolidated indices ranking. Ranking results are compared for any disparity among the methodologies.

Mining of high utility-probability sequential patterns from uncertain databases

PubMed Central

Zhang, Binbin; Fournier-Viger, Philippe; Li, Ting

2017-01-01

High-utility sequential pattern mining (HUSPM) has become an important issue in the field of data mining. Several HUSPM algorithms have been designed to mine high-utility sequential patterns (HUPSPs). They have been applied in several real-life situations such as for consumer behavior analysis and event detection in sensor networks. Nonetheless, most studies on HUSPM have focused on mining HUPSPs in precise data. But in real-life, uncertainty is an important factor as data is collected using various types of sensors that are more or less accurate. Hence, data collected in a real-life database can be annotated with existing probabilities. This paper presents a novel pattern mining framework called high utility-probability sequential pattern mining (HUPSPM) for mining high utility-probability sequential patterns (HUPSPs) in uncertain sequence databases. A baseline algorithm with three optional pruning strategies is presented to mine HUPSPs. Moroever, to speed up the mining process, a projection mechanism is designed to create a database projection for each processed sequence, which is smaller than the original database. Thus, the number of unpromising candidates can be greatly reduced, as well as the execution time for mining HUPSPs. Substantial experiments both on real-life and synthetic datasets show that the designed algorithm performs well in terms of runtime, number of candidates, memory usage, and scalability for different minimum utility and minimum probability thresholds. PMID:28742847

Promoting Critical Reflection: An Evaluation of the Longer-Term Impact of a Substantial Faculty Development Program

ERIC Educational Resources Information Center

Calkins, Susanna; Harris, Muveddet

2017-01-01

For many faculty, critical reflection on teaching and learning requires space and time that is not readily available. For fifteen years, we have run a substantial year-long faculty development program designed to help participants: (1) reflect critically on their teaching and their students' learning; and (2) develop a project related to their…

About the nature of design in universal design.

PubMed

Heylighen, Ann

2014-01-01

Studies suggest that the concept of universal design (UD) is not widely accepted and that some of its ideas are received rather sceptically. This article confronts the concept of UD with prevailing notions and practices of design. It examines how UD can be situated relative to design in general, and explores whether elements in the nature of design can help us explain this scepticism. The article confronts writings about how design is understood with the concept and ideas of UD. This confrontation is substantiated with examples from studies of design processes in architectural design practice. The confrontation highlights the ambiguity of how UD is framed and presented, ranging from an attitude over something utopian to a normative design domain. (1) Besides UD other attitudes are thinkable that address the diversity in human abilities and conditions. (2) The impossibility to really design for everyone may be inherent to design rather than characteristic of UD. (3) Even if UD as a normative design domain were a top priority, the question remains how to assess whether a design is universally usable given the nature of design (problems), and prevailing design practices. Implications for Rehabilitation Understanding disability as originating in the interaction between features of an individual's body and features of his/her environment, as universal design does, implies that rehabilitation specialists need to consider the context in which a person lives. Besides striving for independence, self-reliance and individualism, rehabilitation specialists may consider other attitudes to address the diversity in human abilities and conditions. Designers do not have direct access to the perspective of the people they design for. Assessing whether a design is universally accessible may benefit from expertise of rehabilitation specialists.

Visualization of air flow around soccer ball using a particle image velocimetry

PubMed Central

Hong, Sungchan; Asai, Takeshi; Seo, Kazuya

2015-01-01

A traditional soccer ball is constructed using 32 pentagonal and hexagonal panels. In recent years, however, the likes of the Teamgeist and Jabulani balls, constructed from 14 and 8 panels, respectively, have entered the field, marking a significant departure from conventionality in terms of shape and design. Moreover, the recently introduced Brazuca ball features a new 6-panel design and has already been adopted by many soccer leagues. However, the shapes of the constituent panels of these balls differ substantially from those of conventional balls. Therefore, this study set out to investigate the flight and aerodynamic characteristics of different orientations of the soccer ball, which is constructed from panels of different shapes. A wind tunnel test showed substantial differences in the aerodynamic forces acting on the ball, depending on its orientation. Substantial differences were also observed in the aerodynamic forces acting on the ball in different directions, corresponding to its orientation and rotation. Moreover, two-dimensional particle image velocimetry (2D-PIV) measurements showed that the boundary separation varies depending on the orientation of the ball. Based on these results, we can conclude that the shape of the panels of a soccer ball substantially affects its flight trajectory. PMID:26446616

Visualization of air flow around soccer ball using a particle image velocimetry

NASA Astrophysics Data System (ADS)

Hong, Sungchan; Asai, Takeshi; Seo, Kazuya

2015-10-01

A traditional soccer ball is constructed using 32 pentagonal and hexagonal panels. In recent years, however, the likes of the Teamgeist and Jabulani balls, constructed from 14 and 8 panels, respectively, have entered the field, marking a significant departure from conventionality in terms of shape and design. Moreover, the recently introduced Brazuca ball features a new 6-panel design and has already been adopted by many soccer leagues. However, the shapes of the constituent panels of these balls differ substantially from those of conventional balls. Therefore, this study set out to investigate the flight and aerodynamic characteristics of different orientations of the soccer ball, which is constructed from panels of different shapes. A wind tunnel test showed substantial differences in the aerodynamic forces acting on the ball, depending on its orientation. Substantial differences were also observed in the aerodynamic forces acting on the ball in different directions, corresponding to its orientation and rotation. Moreover, two-dimensional particle image velocimetry (2D-PIV) measurements showed that the boundary separation varies depending on the orientation of the ball. Based on these results, we can conclude that the shape of the panels of a soccer ball substantially affects its flight trajectory.

Future Challenges in Heterogeneous Catalysis: Understanding Catalysts under Dynamic Reaction Conditions

PubMed Central

Kalz, Kai F.; Kraehnert, Ralph; Dvoyashkin, Muslim; Dittmeyer, Roland; Gläser, Roger; Krewer, Ulrike; Reuter, Karsten

2016-01-01

Abstract In the future, (electro‐)chemical catalysts will have to be more tolerant towards a varying supply of energy and raw materials. This is mainly due to the fluctuating nature of renewable energies. For example, power‐to‐chemical processes require a shift from steady‐state operation towards operation under dynamic reaction conditions. This brings along a number of demands for the design of both catalysts and reactors, because it is well‐known that the structure of catalysts is very dynamic. However, in‐depth studies of catalysts and catalytic reactors under such transient conditions have only started recently. This requires studies and advances in the fields of 1) operando spectroscopy including time‐resolved methods, 2) theory with predictive quality, 3) kinetic modelling, 4) design of catalysts by appropriate preparation concepts, and 5) novel/modular reactor designs. An intensive exchange between these scientific disciplines will enable a substantial gain of fundamental knowledge which is urgently required. This concept article highlights recent developments, challenges, and future directions for understanding catalysts under dynamic reaction conditions. PMID:28239429

Electrochemical Evaluations of Fractal Microelectrodes for Energy Efficient Neurostimulation.

PubMed

Park, Hyunsu; Takmakov, Pavel; Lee, Hyowon

2018-03-12

Advancements in microfabrication has enabled manufacturing of microscopic neurostimulation electrodes with smaller footprint than ever possible. The smaller electrodes can potentially reduce tissue damage and allow better spatial resolution for neural stimulation. Although electrodes of any shape can easily be fabricated, substantial effort have been focused on identification and characterization of new materials and surface morphology for efficient charge injection, while maintaining simple circular or rectangular Euclidean electrode geometries. In this work we provide a systematic electrochemical evaluation of charge injection capacities of serpentine and fractal-shaped platinum microelectrodes and compare their performance with traditional circular microelectrodes. Our findings indicate that the increase in electrode perimeter leads to an increase in maximum charge injection capacity. Furthermore, we found that the electrode geometry can have even more significant impact on electrode performance than having a larger perimeter for a given surface area. The fractal-shaped microelectrodes, despite having smaller perimeter than other designs, demonstrated superior charge injection capacity. Our results suggest that electrode design can significantly affect both Faradaic and non-Faradaic electrochemical processes, which may be optimized to enable a more energy efficient design for neurostimulation.

New quality assurance program integrating "modern radiotherapy" within the German Hodgkin Study Group.

PubMed

Kriz, J; Baues, C; Engenhart-Cabillic, R; Haverkamp, U; Herfarth, K; Lukas, P; Schmidberger, H; Marnitz-Schulze, S; Fuchs, M; Engert, A; Eich, H T

2017-02-01

Field design changed substantially from extended-field RT (EF-RT) to involved-field RT (IF-RT) and now to involved-node RT (IN-RT) and involved-site RT (IS-RT) as well as treatment techniques in radiotherapy (RT) of Hodgkin's lymphoma (HL). The purpose of this article is to demonstrate the establishment of a quality assurance program (QAP) including modern RT techniques and field designs within the German Hodgkin Study Group (GHSG). In the era of modern conformal RT, this QAP had to be fundamentally adapted and a new evaluation process has been intensively discussed by the radiotherapeutic expert panel of the GHSG. The expert panel developed guidelines and criteria to analyse "modern" field designs and treatment techniques. This work is based on a dataset of 11 patients treated within the sixth study generation (HD16-17). To develop a QAP of "modern RT", the expert panel defined criteria for analysing current RT procedures. The consensus of a modified QAP in ongoing and future trials is presented. With this schedule, the QAP of the GHSG could serve as a model for other study groups.

Process and apparatus for the production of BI-213 cations

DOEpatents

Horwitz, E. Philip; Hines, John J.; Chiarizia, Renato; Dietz, Mark

1998-01-01

A process for producing substantially impurity-free Bi-213 cations is disclosed. An aqueous acid feed solution containing Ac-225 cations is contacted with an ion exchange medium to bind the Ac-225 cations and form an Ac-225-laden ion exchange medium. The bound Ac-225 incubates on the ion exchange medium to form Bi-213 cations by radioactive decay. The Bi-213 cations are then recovered from the Ac-225-laden ion exchange medium to form a substantially impurity-free aqueous Bi-213 cation acid solution. An apparatus for carrying out this process is also disclosed.

Process and apparatus for the production of Bi-213 cations

DOEpatents

Horwitz, E.P.; Hines, J.J.; Chiarizia, R.; Dietz, M.

1998-12-29

A process for producing substantially impurity-free Bi-213 cations is disclosed. An aqueous acid feed solution containing Ac-225 cations is contacted with an ion exchange medium to bind the Ac-225 cations and form an Ac-225-laden ion exchange medium. The bound Ac-225 incubates on the ion exchange medium to form Bi-213 cations by radioactive decay. The Bi-213 cations are then recovered from the Ac-225-laden ion exchange medium to form a substantially impurity-free aqueous Bi-213 cation acid solution. An apparatus for carrying out this process is also disclosed. 7 figs.

14 CFR 21.97 - Approval of major changes in type design.

Code of Federal Regulations, 2014 CFR

2014-01-01

... must— (1) Provide substantiating data and necessary descriptive data for inclusion in the type design... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Approval of major changes in type design... TRANSPORTATION AIRCRAFT CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS Changes to Type Certificates § 21.97...

14 CFR 21.97 - Approval of major changes in type design.

Code of Federal Regulations, 2012 CFR

2012-01-01

... must— (1) Provide substantiating data and necessary descriptive data for inclusion in the type design... is made unless the applicant identifies in the necessary descriptive data for inclusion in the type... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Approval of major changes in type design...

77 FR 22844 - Agency Information Collection Activity Under OMB Review: Uniform Criteria for State Observational...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-17

... the States have accumulated substantial experience in the design and implementation of these surveys... observational surveys is to include a specification of the survey design, to be reassessed and, if appropriate, updated every five (5) years, or earlier if the State so desires. The survey design specification will...

30 CFR 77.216-5 - Water, sediment or slurry impoundments and impounding structures; abandonment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... are met: (1) A registered professional engineer, knowledgeable in the principles of dam design and in the design and construction of the structure, shall certify that it substantially conforms to the approved design plan and specifications and that there are no apparent defects. (2) The current owner or...

30 CFR 77.216-5 - Water, sediment or slurry impoundments and impounding structures; abandonment.

Code of Federal Regulations, 2011 CFR

2011-07-01

... are met: (1) A registered professional engineer, knowledgeable in the principles of dam design and in the design and construction of the structure, shall certify that it substantially conforms to the approved design plan and specifications and that there are no apparent defects. (2) The current owner or...

Determination of quantitative trait variants by concordance via application of the a posteriori granddaughter design to the U.S. Holstein population

USDA-ARS?s Scientific Manuscript database

Experimental designs that exploit family information can provide substantial predictive power in quantitative trait variant discovery projects. Concordance between quantitative trait locus genotype as determined by the a posteriori granddaughter design and marker genotype was determined for 29 trai...

DOSESCREEN: a computer program to aid dose placement

Treesearch

Kimberly C. Smith; Jacqueline L. Robertson

1984-01-01

Careful selection of an experimental design for a bioassay substantially improves the precision of effective dose (ED) estimates. Design considerations typically include determination of sample size, dose selection, and allocation of subjects to doses. DOSESCREEN is a computer program written to help investigators select an efficient design for the estimation of an...

Forward Swept Compressor Testing

NASA Technical Reports Server (NTRS)

Miller, David P.

1997-01-01

A new forward-swept rotor designed by Allison Engine Company was tested in NASA Lewis Research Center's CE-18 facility. This testing was a follow-on project sponsored by NASA Lewis to study range enhancements in small turbomachinery. The test was conducted against a baseline rotor design that was also tested in CE-18. The design point for the rotor was a rotor pressure ratio of 2.69, a mass flow of 10.52 lbm/sec, and an adiabatic efficiency of 89.1 percent. Test data indicate that the rotor met the pressure ratio of 2.69 with a 10.77 lbm/sec flow rate, a 87.5-percent adiabatic efficiency, and a 19.5-percent stall margin. The baseline rotor achieved a pressure ratio of 2.69 at a 10.77 lbm/sec flow rate with a stall margin of only 9.2 percent and an adiabatic efficiency of 87.0 percent. The major differences are the significant stall margin increase and the substantially higher off-design peak efficiencies of the forward-swept rotor. The substantially higher performance over the baseline rotor design makes the new design a viable technology candidate for future products.

Explanatory Power of Multi-scale Physical Descriptors in Modeling Benthic Indices Across Nested Ecoregions of the Pacific Northwest

NASA Astrophysics Data System (ADS)

Holburn, E. R.; Bledsoe, B. P.; Poff, N. L.; Cuhaciyan, C. O.

2005-05-01

Using over 300 R/EMAP sites in OR and WA, we examine the relative explanatory power of watershed, valley, and reach scale descriptors in modeling variation in benthic macroinvertebrate indices. Innovative metrics describing flow regime, geomorphic processes, and hydrologic-distance weighted watershed and valley characteristics are used in multiple regression and regression tree modeling to predict EPT richness, % EPT, EPT/C, and % Plecoptera. A nested design using seven ecoregions is employed to evaluate the influence of geographic scale and environmental heterogeneity on the explanatory power of individual and combined scales. Regression tree models are constructed to explain variability while identifying threshold responses and interactions. Cross-validated models demonstrate differences in the explanatory power associated with single-scale and multi-scale models as environmental heterogeneity is varied. Models explaining the greatest variability in biological indices result from multi-scale combinations of physical descriptors. Results also indicate that substantial variation in benthic macroinvertebrate response can be explained with process-based watershed and valley scale metrics derived exclusively from common geospatial data. This study outlines a general framework for identifying key processes driving macroinvertebrate assemblages across a range of scales and establishing the geographic extent at which various levels of physical description best explain biological variability. Such information can guide process-based stratification to avoid spurious comparison of dissimilar stream types in bioassessments and ensure that key environmental gradients are adequately represented in sampling designs.

Process for producing silicon

DOEpatents

Olson, J.M.; Carleton, K.L.

1982-06-10

A process of producing silicon includes forming an alloy of copper and silicon and positioning the alloy in a dried, molten salt electrolyte to form a solid anode structure therein. An electrically conductive cathode is placed in the electrolyte for plating silicon thereon. The electrolyte is then purified to remove dissolved oxides. Finally, an electrical potential is applied between the anode and cathode in an amount sufficient to form substantially pure silicon on the cathode in the form of substantially dense, coherent deposits.

Ferrosilicon smelting in a direct current furnace

DOEpatents

Dosaj, V.D.; May, J.B.

1992-12-29

The present invention is a process for smelting ferrosilicon alloy. The process comprises adding a carbon source and tailings comprising oxides of silicon and iron to a substantially closed furnace. Heat is supplied to the furnace by striking a direct current arc between a cathode electrode and an anode functional hearth. In a preferred embodiment of the present invention, the cathode electrode is hollow and feed to the substantially closed furnace is through the hollow electrode. 1 figure.

Process for producing silicon

DOEpatents

Olson, Jerry M.; Carleton, Karen L.

1984-01-01

A process for producing silicon includes forming an alloy of copper and silicon and positioning the alloy in a dried, molten salt electrolyte to form a solid anode structure therein. An electrically conductive cathode is placed in the electrolyte for plating silicon thereon. The electrolyte is then purified to remove dissolved oxides. Finally, an electrical potential is applied between the anode and cathode in an amount sufficient to form substantially pure silicon on the cathode in the form of substantially dense, coherent deposits.

7 CFR 52.807 - Freedom from pits.

Code of Federal Regulations, 2011 CFR

2011-01-01

... PROCESSED FRUITS AND VEGETABLES, PROCESSED PRODUCTS THEREOF, AND CERTAIN OTHER PROCESSED FOOD PRODUCTS 1... substantially free from any adhering sirup, sugar, or other packing medium. (c) (A) Classification. Frozen red...

7 CFR 52.807 - Freedom from pits.

Code of Federal Regulations, 2010 CFR

2010-01-01

... PROCESSED FRUITS AND VEGETABLES, PROCESSED PRODUCTS THEREOF, AND CERTAIN OTHER PROCESSED FOOD PRODUCTS 1... substantially free from any adhering sirup, sugar, or other packing medium. (c) (A) Classification. Frozen red...

7 CFR 52.807 - Freedom from pits.

Code of Federal Regulations, 2012 CFR

2012-01-01

... PROCESSED FRUITS AND VEGETABLES, PROCESSED PRODUCTS THEREOF, AND CERTAIN OTHER PROCESSED FOOD PRODUCTS 1... substantially free from any adhering sirup, sugar, or other packing medium. (c) (A) Classification. Frozen red...

Structures, Material and Processes Technology in the Future Launchers Preparatory Program

NASA Astrophysics Data System (ADS)

Baiocco, P.; Ramusat, G.; Breteau, J.; Bouilly, Th.; Lavelle, Fl.; Cardone, T.; Fischer, H.; Appel, S.; Block, U.

2014-06-01

In the frame of the technology / demonstration activity for European launchers developments and evolutions, a top-down / bottom-up approach has been employed to identify promising technologies and alternative conception. The top-down approach consists in looking for system-driven design solutions and the bottom-up approach features design solutions leading to substantial advantages for the system. The main investigations have been devoted to structures, material and process technology.Preliminary specifications have been used in order to permit sub-system design with the goal to find the major benefit for the overall launch system. In this respect competitiveness factors have been defined to down- select the technology and the corresponding optimized design. The development cost, non-recurring cost, industrialization and operational aspects have been considered for the identification of the most interesting solutions. The TRL/IRL has been assessed depending on the manufacturing company and a preliminary development plan has been issued for some technology.The reference launch systems for the technology and demonstration programs are mainly Ariane 6 with its evolutions, VEGA C/E and others possible longer term systems. Requirements and reference structures architectures have been considered in order to state requirements for representative subscale or full scale demonstrators. The major sub-systems and structures analyzed are for instance the upper stage structures, the engine thrust frame (ETF), the inter stage structures (ISS), the cryogenic propellant tanks, the feeding lines and their attachments, the pressurization systems, the payload adapters and fairings. A specific analysis has been devoted to the efficiency of production processes associated to technologies and design features.The paper provides an overview of the main results of the technology and demonstration activities with the associated system benefits. The materials used for the main structures are metallic and composite owing to sub-systems or sub-assemblies proposed for the European launch systems in development and their evolutions.

LOD BIM Element specification for Railway Turnout Systems Risk Mitigation using the Information Delivery Manual

NASA Astrophysics Data System (ADS)

Gigante-Barrera, Ángel; Dindar, Serdar; Kaewunruen, Sakdirat; Ruikar, Darshan

2017-10-01

Railway turnouts are complex systems designed using complex geometries and grades which makes them difficult to be managed in terms of risk prevention. This feature poses a substantial peril to rail users as it is considered a cause of derailment. In addition, derailment deals to financial losses due to operational downtimes and monetary compensations in case of death or injure. These are fundamental drivers to consider mitigating risks arising from poor risk management during design. Prevention through design (PtD) is a process that introduces tacit knowledge from industry professionals during the design process. There is evidence that Building Information Modelling (BIM) can help to mitigate risk since the inception of the project. BIM is considered an Information System (IS) were tacit knowledge can be stored and retrieved from a digital database making easy to take promptly decisions as information is ready to be analysed. BIM at the model element level entails working with 3D elements and embedded data, therefore adding a layer of complexity to the management of information along the different stages of the project and across different disciplines. In order to overcome this problem, the industry has created a framework for model progression specification named Level of Development (LOD). The paper presents an IDM based framework for design risk mitigation through code validation using the LOD. This effort resulted on risk datasets which describe graphically and non-graphically a rail turnout as the model progresses. Thus, permitting its inclusion within risk information systems. The assignment of an LOD construct to a set of data, requires specialised management and process related expertise. Furthermore, the selection of a set of LOD constructs requires a purpose based analysis. Therefore, a framework for LOD constructs implementation within the IDM for code checking is required for the industry to progress in this particular field.

SISYPHUS: A high performance seismic inversion factory

NASA Astrophysics Data System (ADS)

Gokhberg, Alexey; Simutė, Saulė; Boehm, Christian; Fichtner, Andreas

2016-04-01

In the recent years the massively parallel high performance computers became the standard instruments for solving the forward and inverse problems in seismology. The respective software packages dedicated to forward and inverse waveform modelling specially designed for such computers (SPECFEM3D, SES3D) became mature and widely available. These packages achieve significant computational performance and provide researchers with an opportunity to solve problems of bigger size at higher resolution within a shorter time. However, a typical seismic inversion process contains various activities that are beyond the common solver functionality. They include management of information on seismic events and stations, 3D models, observed and synthetic seismograms, pre-processing of the observed signals, computation of misfits and adjoint sources, minimization of misfits, and process workflow management. These activities are time consuming, seldom sufficiently automated, and therefore represent a bottleneck that can substantially offset performance benefits provided by even the most powerful modern supercomputers. Furthermore, a typical system architecture of modern supercomputing platforms is oriented towards the maximum computational performance and provides limited standard facilities for automation of the supporting activities. We present a prototype solution that automates all aspects of the seismic inversion process and is tuned for the modern massively parallel high performance computing systems. We address several major aspects of the solution architecture, which include (1) design of an inversion state database for tracing all relevant aspects of the entire solution process, (2) design of an extensible workflow management framework, (3) integration with wave propagation solvers, (4) integration with optimization packages, (5) computation of misfits and adjoint sources, and (6) process monitoring. The inversion state database represents a hierarchical structure with branches for the static process setup, inversion iterations, and solver runs, each branch specifying information at the event, station and channel levels. The workflow management framework is based on an embedded scripting engine that allows definition of various workflow scenarios using a high-level scripting language and provides access to all available inversion components represented as standard library functions. At present the SES3D wave propagation solver is integrated in the solution; the work is in progress for interfacing with SPECFEM3D. A separate framework is designed for interoperability with an optimization module; the workflow manager and optimization process run in parallel and cooperate by exchanging messages according to a specially designed protocol. A library of high-performance modules implementing signal pre-processing, misfit and adjoint computations according to established good practices is included. Monitoring is based on information stored in the inversion state database and at present implements a command line interface; design of a graphical user interface is in progress. The software design fits well into the common massively parallel system architecture featuring a large number of computational nodes running distributed applications under control of batch-oriented resource managers. The solution prototype has been implemented on the "Piz Daint" supercomputer provided by the Swiss Supercomputing Centre (CSCS).

Overcoming pitfalls: Results from a mandatory peer review process for written examinations.

PubMed

Wilby, Kyle John; El Hajj, Maguy S; El-Bashir, Marwa; Mraiche, Fatima

2018-04-01

Written assessments are essential components of higher education practices. However, faculty members encounter common pitfalls when designing questions intended to evaluate student-learning outcomes. The objective of this project was to determine the impact of a mandatory examination peer review process on question accuracy, alignment with learning objectives, use of best practices in question design, and language/grammar. A mandatory peer review process was implemented for all midterm (before phase) and final (after phase) examinations. Peer review occurred by two reviewers and followed a pre-defined guidance document. Non-punitive feedback given to faculty members served as the intervention. Frequencies of flagged questions according to guidance categories were compared between phases. A total of 21 midterm and 21 final exam reviews were included in the analysis. A total of 637 questions were reviewed across all midterms and 1003 questions were reviewed across all finals. Few questions were flagged for accuracy and alignment with learning outcomes. The median total proportion of questions flagged for best practices was significantly lower for final exams versus midterm exams (15.8 vs. 6.45%, p = 0.014). The intervention did not influence language and grammar errors (9.68 vs. 10.0% of questions flagged before and after, respectively, p = 0.305). A non-punitive peer review process for written examinations can overcome pitfalls in exam creation and improve best practices in question writing. The peer-review process had a substantial effect at flagging language/grammar errors but error rate did not differ between midterm and final exams. Copyright © 2017 Elsevier Inc. All rights reserved.

Composite media for ion processing

DOEpatents

Mann, Nick R [Blackfoot, ID; Wood, Donald J [Peshastin, WA; Todd, Terry A [Aberdeen, ID; Sebesta, Ferdinand [Prague, CZ

2009-12-08

Composite media, systems, and devices for substantially removing, or otherwise processing, one or more constituents of a fluid stream. The composite media comprise a plurality of beads, each having a matrix substantially comprising polyacrylonitrile (PAN) and supporting one or more active components which are effective in removing, by various mechanisms, one or more constituents from a fluid stream. Due to the porosity and large surface area of the beads, a high level of contact is achieved between composite media of the present invention and the fluid stream being processed. Further, the homogeneity of the beads facilitates use of the beads in high volume applications where it is desired to effectively process a large volume of flow per unit of time.

ClusterCAD: a computational platform for type I modular polyketide synthase design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eng, Clara H.; Backman, Tyler W H; Bailey, Constance B.

Here, we present ClusterCAD, a web-based toolkit designed to leverage the collinear structure and deterministic logic of type I modular polyketide synthases (PKSs) for synthetic biology applications. The unique organization of these megasynthases, combined with the diversity of their catalytic domain building blocks, has fueled an interest in harnessing the biosynthetic potential of PKSs for the microbial production of both novel natural product analogs and industrially relevant small molecules. However, a limited theoretical understanding of the determinants of PKS fold and function poses a substantial barrier to the design of active variants, and identifying strategies to reliably construct functional PKSmore » chimeras remains an active area of research. In this work, we formalize a paradigm for the design of PKS chimeras and introduce ClusterCAD as a computational platform to streamline and simplify the process of designing experiments to test strategies for engineering PKS variants. ClusterCAD provides chemical structures with stereochemistry for the intermediates generated by each PKS module, as well as sequence- and structure-based search tools that allow users to identify modules based either on amino acid sequence or on the chemical structure of the cognate polyketide intermediate. ClusterCAD can be accessed at https://clustercad.jbei.org and at http://clustercad.igb.uci.edu.« less

Baffle aperture design study of hollow cathode equipped ion thrusters. M.S. Thesis Technical Report, 1 Dec. 1979 - 1 Oct. 1980

NASA Technical Reports Server (NTRS)

Brophy, J. R., Jr.; Wilbur, P. J.

1980-01-01

A simple theoretical model which can be used as an aid in the design of the baffle aperture region of a hollow cathode equipped ion thruster was developed. An analysis of the ion and electron currents in both the main and cathode discharge chambers is presented. From this analysis a model of current flow through the aperture, which is required as an input to the design model, was developed. This model was verified experimentally. The dominant force driving electrons through the aperture was the force due to the electrical potential gradient. The diffusion process was modeled according to the Bolm diffusion theory. A number of simplifications were made to limit the amount of detailed plasma information required as input to the model to facilitate the use of the model in thruster design. This simplified model gave remarkably consistant results with experimental results obtained with a given thruster geometry over substantial changes in operating conditions. The model was uncertain to about a factor of two for different thruster cathode region geometries. The design usefulness was limited by this factor of two uncertainty and by the accuracy to which the plasma parameters required as inputs to the model were specified.

ClusterCAD: a computational platform for type I modular polyketide synthase design

DOE PAGES

Eng, Clara H.; Backman, Tyler W H; Bailey, Constance B.; ...

2017-10-11

Here, we present ClusterCAD, a web-based toolkit designed to leverage the collinear structure and deterministic logic of type I modular polyketide synthases (PKSs) for synthetic biology applications. The unique organization of these megasynthases, combined with the diversity of their catalytic domain building blocks, has fueled an interest in harnessing the biosynthetic potential of PKSs for the microbial production of both novel natural product analogs and industrially relevant small molecules. However, a limited theoretical understanding of the determinants of PKS fold and function poses a substantial barrier to the design of active variants, and identifying strategies to reliably construct functional PKSmore » chimeras remains an active area of research. In this work, we formalize a paradigm for the design of PKS chimeras and introduce ClusterCAD as a computational platform to streamline and simplify the process of designing experiments to test strategies for engineering PKS variants. ClusterCAD provides chemical structures with stereochemistry for the intermediates generated by each PKS module, as well as sequence- and structure-based search tools that allow users to identify modules based either on amino acid sequence or on the chemical structure of the cognate polyketide intermediate. ClusterCAD can be accessed at https://clustercad.jbei.org and at http://clustercad.igb.uci.edu.« less

Feasibility study: Atmospheric general circulation experiment, volume 2

NASA Technical Reports Server (NTRS)

Homsey, R. J. (Editor)

1981-01-01

The feasibility analysis of the atmospheric general circulation experiment (AGCE) are documented. The analysis performed in each technical area, the rationale and substantiation for the design approaches selected for the hardware, and the design details for the baseline AGCE are presented.

VARTM Variability and Substantiation

DOT National Transportation Integrated Search

2008-06-18

Presentation overview: establish the fundamental understanding of the various VARTM processes; Flow model is fully developed for SCRIMP, VAP, and CAPRI process; Compaction behavior has been evaluated for all processes; Dry compaction during debulking...

Knowledge Attitude and Perception of Sex Education among School Going Adolescents in Ambala District, Haryana, India: A Cross-Sectional Study.

PubMed

Kumar, Randhir; Goyal, Anmol; Singh, Parmal; Bhardwaj, Anu; Mittal, Anshu; Yadav, Sachin Singh

2017-03-01

Adolescence is a highly dynamic period characterised by rapid growth and development. Adolescents have limited knowledge about sexual and reproduction health, and know little about the natural processes of puberty, sexual health, pregnancy or reproduction. Sex education should be an integral part of the learning process beginning in childhood and continuing into adult life, because it is lifelong process. This study was carried out to identify the knowledge and attitude of imparting sex education in school going adolescents in rural and urban area of Ambala district. A cross sectional study design was used to study the knowledge of reproductive and sexual health among school going children. A total of 743 adolescents from age group of 13-19 year were studied, using self designed semi-structured questionnaire to assess the knowledge regarding reproductive and sexual health among adolescents. The mean age of study subjects was 15.958±1.61 years, majority of adolescents i.e., 93.5% favour sex education. An 86.3% said sex education can prevent the occurrence of AIDS and 91.5% of adolescents prefer doctors should give them sex education followed by 83.0% school/teacher and least preference was parents 37.3%. There were substantial lacunae in the knowledge about reproductive and sexual health. Students felt that sex education is necessary and should be introduced in the school curriculum.

A newly developed tool for classifying study designs in systematic reviews of interventions and exposures showed substantial reliability and validity.

PubMed

Seo, Hyun-Ju; Kim, Soo Young; Lee, Yoon Jae; Jang, Bo-Hyoung; Park, Ji-Eun; Sheen, Seung-Soo; Hahn, Seo Kyung

2016-02-01

To develop a study Design Algorithm for Medical Literature on Intervention (DAMI) and test its interrater reliability, construct validity, and ease of use. We developed and then revised the DAMI to include detailed instructions. To test the DAMI's reliability, we used a purposive sample of 134 primary, mainly nonrandomized studies. We then compared the study designs as classified by the original authors and through the DAMI. Unweighted kappa statistics were computed to test interrater reliability and construct validity based on the level of agreement between the original and DAMI classifications. Assessment time was also recorded to evaluate ease of use. The DAMI includes 13 study designs, including experimental and observational studies of interventions and exposure. Both the interrater reliability (unweighted kappa = 0.67; 95% CI [0.64-0.75]) and construct validity (unweighted kappa = 0.63, 95% CI [0.52-0.67]) were substantial. Mean classification time using the DAMI was 4.08 ± 2.44 minutes (range, 0.51-10.92). The DAMI showed substantial interrater reliability and construct validity. Furthermore, given its ease of use, it could be used to accurately classify medical literature for systematic reviews of interventions although minimizing disagreement between authors of such reviews. Copyright © 2016 Elsevier Inc. All rights reserved.

Advanced Turbine Technology Applications Project (ATTAP)

NASA Technical Reports Server (NTRS)

1990-01-01

Advanced Turbine Technology Application Project (ATTAP) activities during the past year were highlighted by test-bed engine design and development activities; ceramic component design; materials and component characterization; ceramic component process development and fabrication; component rig testing; and test-bed engine fabrication and testing. Although substantial technical challenges remain, all areas exhibited progress. Test-bed engine design and development activity included engine mechanical design, power turbine flow-path design and mechanical layout, and engine system integration aimed at upgrading the AGT-5 from a 1038 C metal engine to a durable 1371 C structural ceramic component test-bed engine. ATTAP-defined ceramic and associated ceramic/metal component design activities include: the ceramic combustor body, the ceramic gasifier turbine static structure, the ceramic gasifier turbine rotor, the ceramic/metal power turbine static structure, and the ceramic power turbine rotors. The materials and component characterization efforts included the testing and evaluation of several candidate ceramic materials and components being developed for use in the ATTAP. Ceramic component process development and fabrication activities are being conducted for the gasifier turbine rotor, gasifier turbine vanes, gasifier turbine scroll, extruded regenerator disks, and thermal insulation. Component rig testing activities include the development of the necessary test procedures and conduction of rig testing of the ceramic components and assemblies. Four-hundred hours of hot gasifier rig test time were accumulated with turbine inlet temperatures exceeding 1204 C at 100 percent design gasifier speed. A total of 348.6 test hours were achieved on a single ceramic rotor without failure and a second ceramic rotor was retired in engine-ready condition at 364.9 test hours. Test-bed engine fabrication, testing, and development supported improvements in ceramic component technology that will permit the achievement of program performance and durability goals. The designated durability engine accumulated 359.3 hour of test time, 226.9 of which were on the General Motors gas turbine durability schedule.

Development of a Mobile Clinical Prediction Tool to Estimate Future Depression Severity and Guide Treatment in Primary Care: User-Centered Design

PubMed Central

2018-01-01

Background Around the world, depression is both under- and overtreated. The diamond clinical prediction tool was developed to assist with appropriate treatment allocation by estimating the 3-month prognosis among people with current depressive symptoms. Delivering clinical prediction tools in a way that will enhance their uptake in routine clinical practice remains challenging; however, mobile apps show promise in this respect. To increase the likelihood that an app-delivered clinical prediction tool can be successfully incorporated into clinical practice, it is important to involve end users in the app design process. Objective The aim of the study was to maximize patient engagement in an app designed to improve treatment allocation for depression. Methods An iterative, user-centered design process was employed. Qualitative data were collected via 2 focus groups with a community sample (n=17) and 7 semistructured interviews with people with depressive symptoms. The results of the focus groups and interviews were used by the computer engineering team to modify subsequent protoypes of the app. Results Iterative development resulted in 3 prototypes and a final app. The areas requiring the most substantial changes following end-user input were related to the iconography used and the way that feedback was provided. In particular, communicating risk of future depressive symptoms proved difficult; these messages were consistently misinterpreted and negatively viewed and were ultimately removed. All participants felt positively about seeing their results summarized after completion of the clinical prediction tool, but there was a need for a personalized treatment recommendation made in conjunction with a consultation with a health professional. Conclusions User-centered design led to valuable improvements in the content and design of an app designed to improve allocation of and engagement in depression treatment. Iterative design allowed us to develop a tool that allows users to feel hope, engage in self-reflection, and motivate them to treatment. The tool is currently being evaluated in a randomized controlled trial. PMID:29685864

The International Safety Framework for nuclear power source applications in outer space-Useful and substantial guidance

NASA Astrophysics Data System (ADS)

Summerer, L.; Wilcox, R. E.; Bechtel, R.; Harbison, S.

2015-06-01

In 2009, the International Safety Framework for Nuclear Power Source Applications in Outer Space was adopted, following a multi-year process that involved all major space faring nations under the auspices of a partnership between the UN Committee on the Peaceful Uses of Outer Space and the International Atomic Energy Agency. The Safety Framework reflects an international consensus on best practices to achieve safety. Following the 1992 UN Principles Relevant to the Use of Nuclear Power Sources in Outer Space, it is the second attempt by the international community to draft guidance promoting the safety of applications of nuclear power sources in space missions. NPS applications in space have unique safety considerations compared with terrestrial applications. Mission launch and outer space operational requirements impose size, mass and other space environment limitations not present for many terrestrial nuclear facilities. Potential accident conditions could expose nuclear power sources to extreme physical conditions. The Safety Framework is structured to provide guidance for both the programmatic and technical aspects of safety. In addition to sections containing specific guidance for governments and for management, it contains technical guidance pertinent to the design, development and all mission phases of space NPS applications. All sections of the Safety Framework contain elements directly relevant to engineers and space mission designers for missions involving space nuclear power sources. The challenge for organisations and engineers involved in the design and development processes of space nuclear power sources and applications is to implement the guidance provided in the Safety Framework by integrating it into the existing standard space mission infrastructure of design, development and operational requirements, practices and processes. This adds complexity to the standard space mission and launch approval processes. The Safety Framework is deliberately generic to remain relevantly independent of technological progress, of national organisational setups and of space mission types. Implementing its guidance therefore leaves room for interpretation and adaptation. Relying on reported practices, we analyse the guidance particularly relevant to engineers and space mission designers.

Friction Stir Welding at MSFC: Kinematics

NASA Technical Reports Server (NTRS)

Nunes, A. C., Jr.

2001-01-01

In 1991 The Welding Institute of the United Kingdom patented the Friction Stir Welding (FSW) process. In FSW a rotating pin-tool is inserted into a weld seam and literally stirs the faying surfaces together as it moves up the seam. By April 2000 the American Welding Society International Welding and Fabricating Exposition featured several exhibits of commercial FSW processes and the 81st Annual Convention devoted a technical session to the process. The FSW process is of interest to Marshall Space Flight Center (MSFC) as a means of avoiding hot-cracking problems presented by the 2195 aluminum-lithium alloy, which is the primary constituent of the Lightweight Space Shuttle External Tank. The process has been under development at MSFC for External Tank applications since the early 1990's. Early development of the FSW process proceeded by cut-and-try empirical methods. A substantial and complex body of data resulted. A theoretical model was wanted to deal with the complexity and reduce the data to concepts serviceable for process diagnostics, optimization, parameter selection, etc. A first step in understanding the FSW process is to determine the kinematics, i.e., the flow field in the metal in the vicinity of the pin-tool. Given the kinematics, the dynamics, i.e., the forces, can be targeted. Given a completed model of the FSW process, attempts at rational design of tools and selection of process parameters can be made.

78 FR 5496 - Certain Paper Shredders, Certain Processes for Manufacturing or Relating to Same and Certain...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-25

... misappropriation of trade secrets, the threat or effect of which is to destroy or substantially injure an industry... misappropriation of trade secrets, the threat or effect of which is to destroy or substantially injure an industry...

45 CFR 150.219 - Final determination.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES REQUIREMENTS RELATING TO HEALTH CARE ACCESS CMS ENFORCEMENT IN GROUP AND INDIVIDUAL INSURANCE MARKETS CMS Enforcement Processes for Determining Whether States... substantially enforce, CMS finds that the failure to substantially enforce has not been corrected, it will send...

An adaptive optics imaging system designed for clinical use

PubMed Central

Zhang, Jie; Yang, Qiang; Saito, Kenichi; Nozato, Koji; Williams, David R.; Rossi, Ethan A.

2015-01-01

Here we demonstrate a new imaging system that addresses several major problems limiting the clinical utility of conventional adaptive optics scanning light ophthalmoscopy (AOSLO), including its small field of view (FOV), reliance on patient fixation for targeting imaging, and substantial post-processing time. We previously showed an efficient image based eye tracking method for real-time optical stabilization and image registration in AOSLO. However, in patients with poor fixation, eye motion causes the FOV to drift substantially, causing this approach to fail. We solve that problem here by tracking eye motion at multiple spatial scales simultaneously by optically and electronically integrating a wide FOV SLO (WFSLO) with an AOSLO. This multi-scale approach, implemented with fast tip/tilt mirrors, has a large stabilization range of ± 5.6°. Our method consists of three stages implemented in parallel: 1) coarse optical stabilization driven by a WFSLO image, 2) fine optical stabilization driven by an AOSLO image, and 3) sub-pixel digital registration of the AOSLO image. We evaluated system performance in normal eyes and diseased eyes with poor fixation. Residual image motion with incremental compensation after each stage was: 1) ~2–3 arc minutes, (arcmin) 2) ~0.5–0.8 arcmin and, 3) ~0.05–0.07 arcmin, for normal eyes. Performance in eyes with poor fixation was: 1) ~3–5 arcmin, 2) ~0.7–1.1 arcmin and 3) ~0.07–0.14 arcmin. We demonstrate that this system is capable of reducing image motion by a factor of ~400, on average. This new optical design provides additional benefits for clinical imaging, including a steering subsystem for AOSLO that can be guided by the WFSLO to target specific regions of interest such as retinal pathology and real-time averaging of registered images to eliminate image post-processing. PMID:26114033

Impact of weak water deficit on growth, photosynthetic primary processes and storage processes in pine and spruce seedlings.

PubMed

Zlobin, Ilya E; Ivanov, Yury V; Kartashov, Alexander V; Sarvin, Boris A; Stavrianidi, Andrey N; Kreslavski, Vladimir D; Kuznetsov, Vladimir V

2018-05-19

We investigated the influence of 40 days of drought on growth, storage processes and primary photosynthetic processes in 3-month-old Scots pine and Norway spruce seedlings growing in perlite culture. Water stress significantly affected seedling water status, whereas absolute dry biomass growth was not substantially influenced. Water stress induced an increase in non-structural carbohydrate content (sugars, sugar alcohols, starch) in the aboveground part of pine seedlings in contrast to spruce seedlings. Due to the relatively low content of sugars and sugar alcohols in seedling organs, their expected contribution to osmotic potential changes was quite low. In contrast to biomass accumulation and storage, photosynthetic primary processes were substantially influenced by water shortage. In spruce seedlings, PSII was more sensitive to water stress than PSI. In particular, electron transport in PSI was stable under water stress despite the substantial decrease of electron transport in PSII. The increase in thermal energy dissipation due to enhancement of non-photochemical quenching (NPQ) was evident in both species under water stress. Simultaneously, the yields of non-regulated energy dissipation in PSII were decreased in pine seedlings under drought. A relationship between growth, photosynthetic activities and storage processes is analysed under weak water deficit.

MIT ASTROMAG 1.7 meter disk magnet design report

NASA Technical Reports Server (NTRS)

Marston, P. G.; Hale, J. R.; Vieira, R.; Zhukovsky, A.; Titus, P. H.; Sullivan, J. D.; Dawson, A. M.

1990-01-01

MIT has proposed a magnet design for ASTROMAG, which has demonstrated substantial improvement in performance as compared with the present HEAO baseline design. Several advantages of the MIT disk design are listed along with design characteristics. Details of field contours and active field regions are shown along with comparisons with other designs. Three alternative design configurations for the ASTROMAG disk coils are summarized. The parameters of the conductors are listed and basic parameters for each of the complete systems are shown.

Permanent magnet edge-field quadrupole

DOEpatents

Tatchyn, R.O.

1997-01-21

Planar permanent magnet edge-field quadrupoles for use in particle accelerating machines and in insertion devices designed to generate spontaneous or coherent radiation from moving charged particles are disclosed. The invention comprises four magnetized rectangular pieces of permanent magnet material with substantially similar dimensions arranged into two planar arrays situated to generate a field with a substantially dominant quadrupole component in regions close to the device axis. 10 figs.

Permanent magnet edge-field quadrupole

DOEpatents

Tatchyn, Roman O.

1997-01-01

Planar permanent magnet edge-field quadrupoles for use in particle accelerating machines and in insertion devices designed to generate spontaneous or coherent radiation from moving charged particles are disclosed. The invention comprises four magnetized rectangular pieces of permanent magnet material with substantially similar dimensions arranged into two planar arrays situated to generate a field with a substantially dominant quadrupole component in regions close to the device axis.

Numerical Study of the Reduction Process in an Oxygen Blast Furnace

NASA Astrophysics Data System (ADS)

Zhang, Zongliang; Meng, Jiale; Guo, Lei; Guo, Zhancheng

2016-02-01

Based on computational fluid dynamics, chemical reaction kinetics, principles of transfer in metallurgy, and other principles, a multi-fluid model for a traditional blast furnace was established. The furnace conditions were simulated with this multi-fluid mathematical model, and the model was verified with the comparison of calculation and measurement. Then a multi-fluid model for an oxygen blast furnace in the gasifier-full oxygen blast furnace process was established based on this traditional blast furnace model. With the established multi-fluid model for an oxygen blast furnace, the basic characteristics of iron ore reduction process in the oxygen blast furnace were summarized, including the changing process of the iron ore reduction degree and the compositions of the burden, etc. The study found that compared to the traditional blast furnace, the magnetite reserve zone in the furnace shaft under oxygen blast furnace condition was significantly reduced, which is conducive to the efficient operation of blast furnace. In order to optimize the oxygen blast furnace design and operating parameters, the iron ore reduction process in the oxygen blast furnace was researched under different shaft tuyere positions, different recycling gas temperatures, and different allocation ratios of recycling gas between the hearth tuyere and the shaft tuyere. The results indicate that these three factors all have a substantial impact on the ore reduction process in the oxygen blast furnace. Moderate shaft tuyere position, high recycling gas temperature, and high recycling gas allocation ratio between hearth and shaft could significantly promote the reduction of iron ore, reduce the scope of the magnetite reserve zone, and improve the performance of oxygen blast furnace. Based on the above findings, the recommendations for improvement of the oxygen blast furnace design and operation were proposed.

A comparison of campfire impacts and policies in seven protected areas

USGS Publications Warehouse

Reid, S.E.; Marion, J.L.

2005-01-01

Using resource-monitoring data from seven protected areas, the effectiveness of three campfire policies-campfire ban, designated campfires, and unregulated campfires-were assessed based on the number of fire sites and the amount of tree damage. Results indicate that unregulated campfire policies permitted substantial numbers of fire sites and tree damage in campsites, although fire bans did not eliminate or even substantially decrease these problems. A designated campfire policy was effective in decreasing number of fire sites, but little difference was found among policies regarding tree damage. Given the importance of campfires to visitor experiences, campfire prohibitions could be viewed as unnecessarily restrictive based on their limited success in preventing resource damage. Conclusions encourage protected-area managers to consider designated campfire policies and prohibitions on axes, hatchets, and saws to better meet resource protection and visitor experience mandates.

OPTIMAL EXPERIMENT DESIGN FOR MAGNETIC RESONANCE FINGERPRINTING

PubMed Central

Zhao, Bo; Haldar, Justin P.; Setsompop, Kawin; Wald, Lawrence L.

2017-01-01

Magnetic resonance (MR) fingerprinting is an emerging quantitative MR imaging technique that simultaneously acquires multiple tissue parameters in an efficient experiment. In this work, we present an estimation-theoretic framework to evaluate and design MR fingerprinting experiments. More specifically, we derive the Cramér-Rao bound (CRB), a lower bound on the covariance of any unbiased estimator, to characterize parameter estimation for MR fingerprinting. We then formulate an optimal experiment design problem based on the CRB to choose a set of acquisition parameters (e.g., flip angles and/or repetition times) that maximizes the signal-to-noise ratio efficiency of the resulting experiment. The utility of the proposed approach is validated by numerical studies. Representative results demonstrate that the optimized experiments allow for substantial reduction in the length of an MR fingerprinting acquisition, and substantial improvement in parameter estimation performance. PMID:28268369

Optimal experiment design for magnetic resonance fingerprinting.

PubMed

Bo Zhao; Haldar, Justin P; Setsompop, Kawin; Wald, Lawrence L

2016-08-01

Magnetic resonance (MR) fingerprinting is an emerging quantitative MR imaging technique that simultaneously acquires multiple tissue parameters in an efficient experiment. In this work, we present an estimation-theoretic framework to evaluate and design MR fingerprinting experiments. More specifically, we derive the Cramér-Rao bound (CRB), a lower bound on the covariance of any unbiased estimator, to characterize parameter estimation for MR fingerprinting. We then formulate an optimal experiment design problem based on the CRB to choose a set of acquisition parameters (e.g., flip angles and/or repetition times) that maximizes the signal-to-noise ratio efficiency of the resulting experiment. The utility of the proposed approach is validated by numerical studies. Representative results demonstrate that the optimized experiments allow for substantial reduction in the length of an MR fingerprinting acquisition, and substantial improvement in parameter estimation performance.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

Frost-protected shallow foundations (FPSFs) offer a proven technology designed to substantially lower construction costs in colder climates, enhancing housing affordability for families in many parts of the United States. This document provides step-by-step procedures to assist building professionals in designing and laying a slab- on-grade FPSF. FPSFs save money over conventional designs by requiring less excavation to construct a frost-proof foundation. It is specially insulated along its perimeter to raise the temperature of the surrounding ground and decrease frost penetration, thus allowing for the construction of a substantially shallower foundation. The FPSF is considered standard practice for homes in Scandinavia,more » where 40 years of field testing has proven it to be economical to construct, durable, and energy efficient. HUD strongly encourages wide spread adoption of FPSF technology in the United States and its incorporation into major model building codes.« less

Temporary storage or permanent removal? The division of nitrogen between biotic assimilation and denitrification in stormwater biofiltration systems.

PubMed

Payne, Emily G I; Fletcher, Tim D; Russell, Douglas G; Grace, Michael R; Cavagnaro, Timothy R; Evrard, Victor; Deletic, Ana; Hatt, Belinda E; Cook, Perran L M

2014-01-01

The long-term efficacy of stormwater treatment systems requires continuous pollutant removal without substantial re-release. Hence, the division of incoming pollutants between temporary and permanent removal pathways is fundamental. This is pertinent to nitrogen, a critical water body pollutant, which on a broad level may be assimilated by plants or microbes and temporarily stored, or transformed by bacteria to gaseous forms and permanently lost via denitrification. Biofiltration systems have demonstrated effective removal of nitrogen from urban stormwater runoff, but to date studies have been limited to a 'black-box' approach. The lack of understanding on internal nitrogen processes constrains future design and threatens the reliability of long-term system performance. While nitrogen processes have been thoroughly studied in other environments, including wastewater treatment wetlands, biofiltration systems differ fundamentally in design and the composition and hydrology of stormwater inflows, with intermittent inundation and prolonged dry periods. Two mesocosm experiments were conducted to investigate biofilter nitrogen processes using the stable isotope tracer 15NO3(-) (nitrate) over the course of one inflow event. The immediate partitioning of 15NO3(-) between biotic assimilation and denitrification were investigated for a range of different inflow concentrations and plant species. Assimilation was the primary fate for NO3(-) under typical stormwater concentrations (∼1-2 mg N/L), contributing an average 89-99% of 15NO3(-) processing in biofilter columns containing the most effective plant species, while only 0-3% was denitrified and 0-8% remained in the pore water. Denitrification played a greater role for columns containing less effective species, processing up to 8% of 15NO3(-), and increased further with nitrate loading. This study uniquely applied isotope tracing to biofiltration systems and revealed the dominance of assimilation in stormwater biofilters. The findings raise important questions about nitrogen release upon plant senescence, seasonally and in the long term, which have implications on the management and design of biofiltration systems.

The Innovation Blaze-Method of Development Professional Thinking Designers in the Modern Higher Education

ERIC Educational Resources Information Center

Alekseeva, Irina V.; Barsukova, Natalia I.; Pallotta, Valentina I.; Skovorodnikova, Nadia A.

2017-01-01

This article proved the urgency of the problem of development of professional thinking of students studying design in modern conditions of higher education. The authors substantiate for the need of an innovative Blaise-method development of professional design thinking of students in higher education. "Blaise-method" named by us in…

Quenching and Partitioning Process Development to Replace Hot Stamping of High Strength Automotive Steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Moor, Emmanuel

The present project investigated Quenching and Partitioning (Q&P) to process cold rolled steels to develop high strength sheet steels that exhibit superior ductility compared to available grades with the intent to allow forming of high strength parts at room temperature to provide an alternative to hot stamping of parts. Hot stamping of boron alloyed steel is the current technology to manufacture thinner gauge sections in automotive structures to guarantee anti-intrusion during collisions whilst improving fuel efficiency by decreasing vehicle weight. Hot stamping involves reheating steel to 900 °C or higher followed by deformation and quenching in the die to producemore » ultra-high strength materials. Hot stamping requires significant energy to reheat the steel and is less productive than traditional room temperature stamping operations. Stamping at elevated temperature was developed due to the lack of available steels with strength levels of interest possessing sufficient ductility enabling traditional room temperature forming. This process is seeing growing demand within the automotive industry and, given the reheating step in this operation, increased energy consumption during part manufacturing results. The present research program focused on the development of steel grades via Q&P processing that exhibit high strength and formability enabling room temperature forming to replace hot stamping. The main project objective consisted of developing sheet steels exhibiting minimum ultimate tensile strength levels of 1200 MPa in combination with minimum tensile elongation levels of 15 pct using Q&P processing through judicious alloy design and heat treating parameter definition. In addition, detailed microstructural characterization and study of properties, processing and microstructure interrelationships were pursued to develop strategies to further enhance tensile properties. In order to accomplish these objectives, alloy design was conducted towards achieving the target properties. Twelve alloys were designed and laboratory produced involving melting, alloying, casting, hot rolling, and cold rolling to obtain sheet steels of approximately 1 mm thickness. Q&P processing of the samples was then conducted. Target properties were achieved and substantially exceeded demonstrating success in the developed and employed alloy design approaches. The best combinations of tensile properties were found at approximately 1550 MPa with a total elongation in excess of 20 pct clearly showing the potential for replacement of hot stamping to produce advanced high strength steels.« less

Viewpoints of Parents and Nurses on How to Design Products to Enhance Parent-Infant Bonding at Neonatal Intensive Care Units: A Qualitative Study Based on Existing Designs.

PubMed

Schrauwen, Laura; Kommers, Deedee R; Oetomo, Sidarto Bambang

2018-04-01

To investigate how product design can be used to improve parent-infant bonding in a neonatal intensive care unit. Impaired parent-infant bonding is an inevitable consequence of premature birth, which negatively influences development. Products, systems, or services that support the bonding process might counter these negative influences. The first step was to trace existing products by performing a literature search in PubMed, the university library, and Google. The identified existing designs were then used in semistructured interviews with nurses and parents to get insights into their desires and recommendations for product design to enhance bonding. Interviews contained open questions and a multiple-choice questionnaire based on the literature search. In total, 17 existing design types were used in interviews with 11 parents and 23 nurses. All nurses explicitly stated that practicality was the first criterion designs aimed at enhancing bonding definitely had to meet. All parents indicated that they would like to use a design to enhance bonding if that would contribute to their child's health and development. For both parents and nurses, the most valuable way to enhance bonding seemed to be products to improve Kangaroo care; however, their specific desires varied substantially. Therefore, seven recurring themes were defined, resulting in nine general recommendations and six opportunities intended to enhance parent-infant bonding. This study provides design recommendations and opportunities based on parents' and nurses' expert opinions. Designing to enhance bonding is considered valuable; however, designs should match the stakeholders' desires and conditions.

Attractors in Sequence Space: Agent-Based Exploration of MHC I Binding Peptides.

PubMed

Jäger, Natalie; Wisniewska, Joanna M; Hiss, Jan A; Freier, Anja; Losch, Florian O; Walden, Peter; Wrede, Paul; Schneider, Gisbert

2010-01-12

Ant Colony Optimization (ACO) is a meta-heuristic that utilizes a computational analogue of ant trail pheromones to solve combinatorial optimization problems. The size of the ant colony and the representation of the ants' pheromone trails is unique referring to the given optimization problem. In the present study, we employed ACO to generate novel peptides that stabilize MHC I protein on the plasma membrane of a murine lymphoma cell line. A jury of feedforward neural network classifiers served as fitness function for peptide design by ACO. Bioactive murine MHC I H-2K(b) stabilizing as well as nonstabilizing octapeptides were designed, synthesized and tested. These peptides reveal residue motifs that are relevant for MHC I receptor binding. We demonstrate how the performance of the implemented ACO algorithm depends on the colony size and the size of the search space. The actual peptide design process by ACO constitutes a search path in sequence space that can be visualized as trajectories on a self-organizing map (SOM). By projecting the sequence space on a SOM we visualize the convergence of the different solutions that emerge during the optimization process in sequence space. The SOM representation reveals attractors in sequence space for MHC I binding peptides. The combination of ACO and SOM enables systematic peptide optimization. This technique allows for the rational design of various types of bioactive peptides with minimal experimental effort. Here, we demonstrate its successful application to the design of MHC-I binding and nonbinding peptides which exhibit substantial bioactivity in a cell-based assay. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Comparative analysis of specialization in palliative medicine processes within the World Health Organization European region.

PubMed

Centeno, Carlos; Bolognesi, Deborah; Biasco, Guido

2015-05-01

Palliative medicine (PM), still in the development phase, is a new, growing specialty aimed at caring for both oncology and non-oncology patients. There is still confusion about the training offered in the various European PM certification programs. To provide a detailed, comparative update and analysis of the PM certification process in Europe, including the different training approaches and their main features. Experts from each country completed an online survey addressing historical background, program name, training requirements, length of time in training, characteristic and content, official certifying institution, effectiveness of accreditation, and 2013 workforce capacity. We prepared a comparative analysis of the data provided. In 2014, 18 of 53 European countries had official programs on specialization in PM (POSPM): Czech Republic, Denmark, Finland, France, Georgia, Germany, Hungary, Ireland, Israel, Italy, Latvia, Malta, Norway, Poland, Portugal, Romania, Slovakia, and the U.K. Ten of these programs were begun in the last five years. The PM is recognized as a "specialty," "subspecialty," or "special area of competence," with no substantial differences between the last two designations. The certification contains the term "palliative medicine" in most countries. Clinical training varies, with one to two years being the most frequent duration. There is a clear trend toward establishing the POSPM as a mandatory condition for obtaining a clinical PM position in countries' respective health systems. PM is growing as a specialization field in Europe. Processes leading to certification are generally long and require substantial clinical training. The POSPM education plans are heterogeneous. The European Association for Palliative Care should commit to establishing common learning standards, leading to additional European-based recognition of expertise in PM. Copyright © 2015 American Academy of Hospice and Palliative Medicine. Published by Elsevier Inc. All rights reserved.

Simulation of surface processes

PubMed Central

Jónsson, Hannes

2011-01-01

Computer simulations of surface processes can reveal unexpected insight regarding atomic-scale structure and transitions. Here, the strengths and weaknesses of some commonly used approaches are reviewed as well as promising avenues for improvements. The electronic degrees of freedom are usually described by gradient-dependent functionals within Kohn–Sham density functional theory. Although this level of theory has been remarkably successful in numerous studies, several important problems require a more accurate theoretical description. It is important to develop new tools to make it possible to study, for example, localized defect states and band gaps in large and complex systems. Preliminary results presented here show that orbital density-dependent functionals provide a promising avenue, but they require the development of new numerical methods and substantial changes to codes designed for Kohn–Sham density functional theory. The nuclear degrees of freedom can, in most cases, be described by the classical equations of motion; however, they still pose a significant challenge, because the time scale of interesting transitions, which typically involve substantial free energy barriers, is much longer than the time scale of vibrations—often 10 orders of magnitude. Therefore, simulation of diffusion, structural annealing, and chemical reactions cannot be achieved with direct simulation of the classical dynamics. Alternative approaches are needed. One such approach is transition state theory as implemented in the adaptive kinetic Monte Carlo algorithm, which, thus far, has relied on the harmonic approximation but could be extended and made applicable to systems with rougher energy landscape and transitions through quantum mechanical tunneling. PMID:21199939

A Cognitive Task Analysis for an Emergency Management Serious Game.

PubMed

Dass, Susan; Barnieu, Joanne; Cummings, Paul; Cid, Victor

2016-01-01

The Bethesda Hospitals' Emergency Preparedness Partnership identified a need to design training systems for hospital emergency management scenarios that included incident command situations. As part of this partnership, the National Library of Medicine (NLM) was challenged to develop an engaging, learner-centered simulation to specifically address hospital procedures for highly infectious diseases (HIDs) for multiple hospital roles. A serious game approach was selected for the simulation because collaborative (multiplayer) immersive, game-based simulations have been proven to generate realistic and engaging learning experiences and, when properly designed, can enhance training while minimizing cost compared to full-scale disaster exercises (Spain et al., 2013). Although substantial research effort has been put into design and evaluation of serious games, less time has been spent on developing sound instructional design methodologies to support serious game development. So how does one collect the appropriate, relevant, contextualized content and then align with serious game design elements? This paper describes how a cognitive task approach supported by a live demonstration with a think-aloud protocol was used to collect the rich psychomotor, procedural, and cognitive data necessary for the design of a serious game for handling HIDs. Furthermore, the paper presents a process to translate the collected data into meaningful content to support rapid prototyping. Recommendations for data collection and translation for a serious game close the paper.

A Cognitive Task Analysis for an Emergency Management Serious Game

PubMed Central

Dass, Susan; Barnieu, Joanne; Cummings, Paul; Cid, Victor

2017-01-01

The Bethesda Hospitals' Emergency Preparedness Partnership identified a need to design training systems for hospital emergency management scenarios that included incident command situations. As part of this partnership, the National Library of Medicine (NLM) was challenged to develop an engaging, learner-centered simulation to specifically address hospital procedures for highly infectious diseases (HIDs) for multiple hospital roles. A serious game approach was selected for the simulation because collaborative (multiplayer) immersive, game-based simulations have been proven to generate realistic and engaging learning experiences and, when properly designed, can enhance training while minimizing cost compared to full-scale disaster exercises (Spain et al., 2013). Although substantial research effort has been put into design and evaluation of serious games, less time has been spent on developing sound instructional design methodologies to support serious game development. So how does one collect the appropriate, relevant, contextualized content and then align with serious game design elements? This paper describes how a cognitive task approach supported by a live demonstration with a think-aloud protocol was used to collect the rich psychomotor, procedural, and cognitive data necessary for the design of a serious game for handling HIDs. Furthermore, the paper presents a process to translate the collected data into meaningful content to support rapid prototyping. Recommendations for data collection and translation for a serious game close the paper. PMID:29629430

Sodium metasilicate based fiber opening for greener leather processing.

PubMed

Saravanabhavan, Subramani; Thanikaivelan, Palanisamy; Rao, Jonnalagadda Raghava; Nair, Balachandran Unni; Ramasamit, Thirumalachari

2008-03-01

Growing environmental regulations propound the need for a transformation in the current practice of leather making. The conventional dehairing and fiber opening process results in high negative impact on the environment because of its uncleanliness. This process accounts for most of the biochemical oxygen demand and chemical oxygen demand in tannery wastewater and generation of H2S gas. Hence, this study explores the use of a biological material and a nontoxic chemical for performing the above process more cleanly. In this study, the dehairing and fiber opening processes has been designed using enzyme and sodium metasilicate. The amount of sodium metasilicate required for fiber opening is standardized through the removal of proteoglycan, increase in weight, and bulk properties of leathers. It has been found that the extent of opening up of fiber bundles is comparable to that of conventionally processed leathers using a 2% sodium metasilicate solution. This has been substantiated through scanning electron microscopic analysis and softness measurements. The presence of silica in the crust leather enhances the bulk properties of the leather. This has been confirmed from the energy dispersive X-ray analysis. Performance of the leathers is shown to be on par with conventionally processed leathers through physical and hand evaluation. The process also exhibits significant reduction in chemical oxygen demand and total solid loads by 55 and 24%, respectively. Further, this newly developed process seems to be economically beneficial.

Thermal processing of a poorly water-soluble drug substance exhibiting a high melting point: the utility of KinetiSol® Dispersing.

PubMed

Hughey, Justin R; Keen, Justin M; Brough, Chris; Saeger, Sophie; McGinity, James W

2011-10-31

Poorly water-soluble drug substances that exhibit high melting points are often difficult to successfully process by fusion-based techniques. The purpose of this study was to identify a suitable polymer system for meloxicam (MLX), a high melting point class II BCS compound, and investigate thermal processing techniques for the preparation of chemically stable single phase solid dispersions. Thermal and solution based screening techniques were utilized to screen hydrophilic polymers suitable for immediate release formulations. Results of the screening studies demonstrated that Soluplus(®)(SOL) provided the highest degree of miscibility and solubility enhancement. A hot-melt extrusion feasibility study demonstrated that high temperatures and extended residence times were required in order to render compositions amorphous, causing significant degradation of MLX. A design of experiments (DOE) was conducted on the KinetiSol(®) Dispersing (KSD) process to evaluate the effect of processing conditions on the chemical stability and amorphous character of MLX. The study demonstrated that ejection temperature significantly impacted MLX stability. All samples prepared by KSD were substantially amorphous. Dissolution analysis of the KSD processed solid dispersions showed increased dissolution rates and extent of supersaturation over the marketed generic MLX tablets. Copyright © 2011 Elsevier B.V. All rights reserved.

RFID in the blood supply chain--increasing productivity, quality and patient safety.

PubMed

Briggs, Lynne; Davis, Rodeina; Gutierrez, Alfonso; Kopetsky, Matthew; Young, Kassandra; Veeramani, Raj

2009-01-01

As part of an overall design of a new, standardized RFID-enabled blood transfusion medicine supply chain, an assessment was conducted for two hospitals: the University of Iowa Hospital and Clinics (UIHC) and Mississippi Baptist Health System (MBHS). The main objectives of the study were to assess RFID technological and economic feasibility, along with possible impacts to productivity, quality and patient safety. A step-by-step process analysis focused on the factors contributing to process "pain points" (errors, inefficiency, product losses). A process re-engineering exercise produced blueprints of RFID-enabled processes to alleviate or eliminate those pain-points. In addition, an innovative model quantifying the potential reduction in adverse patient effects as a result of RFID implementation was created, allowing improvement initiatives to focus on process areas with the greatest potential impact to patient safety. The study concluded that it is feasible to implement RFID-enabled processes, with tangible improvements to productivity and safety expected. Based on a comprehensive cost/benefit model, it is estimated for a large hospital (UIHC) to recover investment from implementation within two to three years, while smaller hospitals may need longer to realize ROI. More importantly, the study estimated that RFID technology could reduce morbidity and mortality effects substantially among patients receiving transfusions.

Adaptations in bacterial catabolic enzyme activity and community structure in membrane-coupled bioreactors fed simple synthetic wastewater.

PubMed

LaPara, Timothy M; Klatt, Christian G; Chen, Ruoyu

2006-02-10

Membrane-coupled bioreactors (MBRs) offer substantial benefits compared to conventional reactor designs for biological wastewater treatment. MBR treatment efficiency, however, has not been optimized because the effects of the MBR on process microbiology are poorly understood. In this study, the structure and function of the microbial communities growing in MBRs fed simple synthetic wastewater were investigated. In four starch-fed MBRs, the bacterial community substantially increased its alpha-glucosidase affinity (>1000-fold), while the leucine aminopeptidase and heptanoate esterase affinities increased slightly (<40-fold) or remained relatively constant. Concomitant to these physiological adaptations, shifts in the bacterial community structure in two of the starch-fed MBRs were detected by PCR-DGGE. Four of the bacterial populations detected by PCR-DGGE were isolated and exhibited specific growth rates in batch culture ranging from 0.009 to 0.22 h(-1). Our results suggest that bacterial communities growing under increasingly stringent nutrient limitation adapt their enzyme activities primarily for the nutrients provided, but that there is also a more subtle response not linked to the substrates included in the feed medium. Our research also demonstrates that MBRs can support relatively complex bacterial communities even on simple feed media.

Using bacterial biomarkers to identify early indicators of cystic fibrosis pulmonary exacerbation onset

PubMed Central

Rogers, Geraint B; Hoffman, Lucas R; Johnson, Matt W; Mayer-Hamblett, Nicole; Schwarze, Jürgen; Carroll, Mary P; Bruce, Kenneth D

2011-01-01

Acute periods of pulmonary exacerbation are the single most important cause of morbidity in cystic fibrosis patients, and may be associated with a loss of lung function. Intervening prior to the onset of a substantially increased inflammatory response may limit the associated damage to the airways. While a number of biomarker assays based on inflammatory markers have been developed, providing useful and important measures of disease during these periods, such factors are typically only elevated once the process of exacerbation has been initiated. Identifying biomarkers that can predict the onset of pulmonary exacerbation at an early stage would provide an opportunity to intervene before the establishment of a substantial immune response, with major implications for the advancement of cystic fibrosis care. The precise triggers of pulmonary exacerbation remain to be determined; however, the majority of models relate to the activity of microbes present in the patient's lower airways of cystic fibrosis. Advances in diagnostic microbiology now allow for the examination of these complex systems at a level likely to identify factors on which biomarker assays can be based. In this article, we discuss key considerations in the design and testing of assays that could predict pulmonary exacerbations. PMID:21405970

The development of a collaborative virtual environment for finite element simulation

NASA Astrophysics Data System (ADS)

Abdul-Jalil, Mohamad Kasim

Communication between geographically distributed designers has been a major hurdle in traditional engineering design. Conventional methods of communication, such as video conferencing, telephone, and email, are less efficient especially when dealing with complex design models. Complex shapes, intricate features and hidden parts are often difficult to describe verbally or even using traditional 2-D or 3-D visual representations. Virtual Reality (VR) and Internet technologies have provided a substantial potential to bridge the present communication barrier. VR technology allows designers to immerse themselves in a virtual environment to view and manipulate this model just as in real-life. Fast Internet connectivity has enabled fast data transfer between remote locations. Although various collaborative virtual environment (CVE) systems have been developed in the past decade, they are limited to high-end technology that is not accessible to typical designers. The objective of this dissertation is to discover and develop a new approach to increase the efficiency of the design process, particularly for large-scale applications wherein participants are geographically distributed. A multi-platform and easily accessible collaborative virtual environment (CVRoom), is developed to accomplish the stated research objective. Geographically dispersed designers can meet in a single shared virtual environment to discuss issues pertaining to the engineering design process and to make trade-off decisions more quickly than before, thereby speeding the entire process. This 'faster' design process will be achieved through the development of capabilities to better enable the multidisciplinary and modeling the trade-off decisions that are so critical before launching into a formal detailed design. The features of the environment developed as a result of this research include the ability to view design models, use voice interaction, and to link engineering analysis modules (such as Finite Element Analysis module, such as is demonstrated in this work). One of the major issues in developing a CVE system for engineering design purposes is to obtain any pertinent simulation results in real-time. This is critical so that the designers can make decisions based on these results quickly. For example, in a finite element analysis, if a design model is changed or perturbed, the analysis results must be obtained in real-time or near real-time to make the virtual meeting environment realistic. In this research, the finite difference-based Design Sensitivity Analysis (DSA) approach is employed to approximate structural responses (i.e. stress, displacement, etc), so as to demonstrate the applicability of CVRoom for engineering design trade-offs. This DSA approach provides for fast approximation and is well-suited for the virtual meeting environment where fast response time is required. The DSA-based approach is tested on several example test problems to show its applicability and limitations. This dissertation demonstrates that an increase in efficiency and reduction of time required for a complex design processing can be accomplished using the approach developed in this dissertation research. Several implementations of CVRoom by students working on common design tasks were investigated. All participants confirmed the preference of using the collaborative virtual environment developed in this dissertation work (CVRoom) over other modes of interactions. It is proposed here that CVRoom is representative of the type of collaborative virtual environment that will be used by most designers in the future to reduce the time required in a design cycle and thereby reduce the associated cost.

Process for the conversion of carbonaceous feedstocks to particulate carbon and methanol

DOEpatents

Steinberg, Meyer; Grohse, Edward W.

1995-01-01

A process for the production of a pollutant-free particulate carbon (i.e., a substantially ash-, sulfur- and nitrogen-free carbon) from carbonaceous feedstocks. The basic process involves de-oxygenating one of the gas streams formed in a cyclic hydropyrolysis-methane pyrolysis process in order to improve conversion of the initial carbonaceous feedstock. De-oxygenation is effected by catalytically converting carbon monoxide, carbon dioxide, and hydrogen contained in one of the pyrolysis gas streams, preferably the latter, to a methanol co-product. There are thus produced two products whose use is known per se, viz., a substantially pollutant-free particulate carbon black and methanol. These products may be admixed in the form of a liquid slurry of carbon black in methanol.

Unified methodology for airport pavement analysis and design. Vol. 1, state of the art

DOT National Transportation Integrated Search

1991-06-01

This report presents an assessment of the state of the art of airport pavement analysis : and design. The objective is to identify those areas in current airport pavement : analysis methodology that need to be substantially improved from the perspect...

48 CFR 252.225-7017 - Photovoltaic Devices.

Code of Federal Regulations, 2014 CFR

2014-10-01

... substantially transformed outside of a Caribbean Basin country. Designated country means— (i) A World Trade..., Spain, Sweden, Switzerland, Taiwan (known in the World Trade Organization as “the Separate Customs..., qualifying country, or designated country photovoltaic devices. (End of clause) [76 FR 78861, Dec. 20, 2011...

AN IMPROVED PORTABLE SURGICAL TABLE FOR THE FIELD AND LABORATORY

EPA Science Inventory

I substantially modified a portable surgical table design by Courtois (1981) to increase its durability and utility. The new design incorporated durable plastic components, a nonskid neoprene surgery surface, and surgical tool bins. The system was used to implant fish and amphibi...

From link-prediction in brain connectomes and protein interactomes to the local-community-paradigm in complex networks

PubMed Central

Cannistraci, Carlo Vittorio; Alanis-Lobato, Gregorio; Ravasi, Timothy

2013-01-01

Growth and remodelling impact the network topology of complex systems, yet a general theory explaining how new links arise between existing nodes has been lacking, and little is known about the topological properties that facilitate link-prediction. Here we investigate the extent to which the connectivity evolution of a network might be predicted by mere topological features. We show how a link/community-based strategy triggers substantial prediction improvements because it accounts for the singular topology of several real networks organised in multiple local communities - a tendency here named local-community-paradigm (LCP). We observe that LCP networks are mainly formed by weak interactions and characterise heterogeneous and dynamic systems that use self-organisation as a major adaptation strategy. These systems seem designed for global delivery of information and processing via multiple local modules. Conversely, non-LCP networks have steady architectures formed by strong interactions, and seem designed for systems in which information/energy storage is crucial. PMID:23563395

Development program on a cold cathode electron gun

NASA Technical Reports Server (NTRS)

Spindt, C. A.

1979-01-01

A prototype electron gun with a field emitter cathode capable of producing 95 mA in a 1/4 mm diameter beam at 12 kV was produced. Achievement of this goal required supporting studies in cathode fabrication, cathode performance, gun design, cathode mounting and gun fabrication. A series of empirical investigations advanced fabrication technology: More stable emitters were produced and multiple cone failure caused by chain reaction discharges were reduced. The cathode is capable of producing well over 95 mA, but a substantial collector development effort was required to demonstrate emission levels in the 100 mA region. Space charge problems made these levels difficult to achieve. Recommendations are made for future process and materials investigation. Electron gun designs were modeled and tested. A pair of two-electrode gun structures were fabricated and tested; one gun was delivered to NASA. Cathodes were pretested up to 100 mA at SRI and delivered to NASA for test in the gun structure.

A Method for Optimizing Lightweight-Gypsum Design Based on Sequential Measurements of Physical Parameters

NASA Astrophysics Data System (ADS)

Vimmrová, Alena; Kočí, Václav; Krejsová, Jitka; Černý, Robert

2016-06-01

A method for lightweight-gypsum material design using waste stone dust as the foaming agent is described. The main objective is to reach several physical properties which are inversely related in a certain way. Therefore, a linear optimization method is applied to handle this task systematically. The optimization process is based on sequential measurement of physical properties. The results are subsequently point-awarded according to a complex point criterion and new composition is proposed. After 17 trials the final mixture is obtained, having the bulk density equal to (586 ± 19) kg/m3 and compressive strength (1.10 ± 0.07) MPa. According to a detailed comparative analysis with reference gypsum, the newly developed material can be used as excellent thermally insulating interior plaster with the thermal conductivity of (0.082 ± 0.005) W/(m·K). In addition, its practical application can bring substantial economic and environmental benefits as the material contains 25 % of waste stone dust.

The desktop interface in intelligent tutoring systems

NASA Technical Reports Server (NTRS)

Baudendistel, Stephen; Hua, Grace

1987-01-01

The interface between an Intelligent Tutoring System (ITS) and the person being tutored is critical to the success of the learning process. If the interface to the ITS is confusing or non-supportive of the tutored domain, the effectiveness of the instruction will be diminished or lost entirely. Consequently, the interface to an ITS should be highly integrated with the domain to provide a robust and semantically rich learning environment. In building an ITS for ZetaLISP on a LISP Machine, a Desktop Interface was designed to support a programming learning environment. Using the bitmapped display, windows, and mouse, three desktops were designed to support self-study and tutoring of ZetaLISP. Through organization, well-defined boundaries, and domain support facilities, the desktops provide substantial flexibility and power for the student and facilitate learning ZetaLISP programming while screening the student from the complex LISP Machine environment. The student can concentrate on learning ZetaLISP programming and not on how to operate the interface or a LISP Machine.

Analysis of multiple pulse NMR in solids. III

NASA Technical Reports Server (NTRS)

Burum, D. P.; Rhim, W. K.

1979-01-01

The paper introduces principles which greatly simplify the process of designing and analyzing compound pulse cycles. These principles are demonstrated by applying them to the design and analysis of several cycles, including a 52-pulse cycle; this pulse cycle combines six different REV-8 cycles and has substantially more resolving power than previously available techniques. Also, a new 24-pulse cycle is introduced which combines three different REV-8 cycles and has a resolving ability equivalent to that of the 52-pulse cycle. The principle of pulse-cycle decoupling provides a method for systematically combining pulse groups into compound cycles in order to achieve enhanced performance. This method is illustrated by a logical development from the two-pulse solid echo sequence to the WAHUHA (Waugh et al., 1968), the REV-8, and the new 24-pulse and 52-pulse cycles, along with the 14-pulse and 12-pulse cycles. Proton chemical shift tensor components for several organic solids, measured by using the 52-pulse cycle, are reported without detailed discussion.

A Framework to Expand and Advance Probabilistic Risk Assessment to Support Small Modular Reactors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curtis Smith; David Schwieder; Robert Nourgaliev

2012-09-01

During the early development of nuclear power plants, researchers and engineers focused on many aspects of plant operation, two of which were getting the newly-found technology to work and minimizing the likelihood of perceived accidents through redundancy and diversity. As time, and our experience, has progressed, the realization of plant operational risk/reliability has entered into the design, operation, and regulation of these plants. But, to date, we have only dabbled at the surface of risk and reliability technologies. For the next generation of small modular reactors (SMRs), it is imperative that these technologies evolve into an accepted, encompassing, validated, andmore » integral part of the plant in order to reduce costs and to demonstrate safe operation. Further, while it is presumed that safety margins are substantial for proposed SMR designs, the depiction and demonstration of these margins needs to be better understood in order to optimize the licensing process.« less

A bipedal DNA Brownian motor with coordinated legs.

PubMed

Omabegho, Tosan; Sha, Ruojie; Seeman, Nadrian C

2009-04-03

A substantial challenge in engineering molecular motors is designing mechanisms to coordinate the motion between multiple domains of the motor so as to bias random thermal motion. For bipedal motors, this challenge takes the form of coordinating the movement of the biped's legs so that they can move in a synchronized fashion. To address this problem, we have constructed an autonomous DNA bipedal walker that coordinates the action of its two legs by cyclically catalyzing the hybridization of metastable DNA fuel strands. This process leads to a chemically ratcheted walk along a directionally polar DNA track. By covalently cross-linking aliquots of the walker to its track in successive walking states, we demonstrate that this Brownian motor can complete a full walking cycle on a track whose length could be extended for longer walks. We believe that this study helps to uncover principles behind the design of unidirectional devices that can function without intervention. This device should be able to fulfill roles that entail the performance of useful mechanical work on the nanometer scale.

From link-prediction in brain connectomes and protein interactomes to the local-community-paradigm in complex networks.

PubMed

Cannistraci, Carlo Vittorio; Alanis-Lobato, Gregorio; Ravasi, Timothy

2013-01-01

Growth and remodelling impact the network topology of complex systems, yet a general theory explaining how new links arise between existing nodes has been lacking, and little is known about the topological properties that facilitate link-prediction. Here we investigate the extent to which the connectivity evolution of a network might be predicted by mere topological features. We show how a link/community-based strategy triggers substantial prediction improvements because it accounts for the singular topology of several real networks organised in multiple local communities - a tendency here named local-community-paradigm (LCP). We observe that LCP networks are mainly formed by weak interactions and characterise heterogeneous and dynamic systems that use self-organisation as a major adaptation strategy. These systems seem designed for global delivery of information and processing via multiple local modules. Conversely, non-LCP networks have steady architectures formed by strong interactions, and seem designed for systems in which information/energy storage is crucial.

Socio-Technical Perspective on Interdisciplinary Interactions During the Development of Complex Engineered Systems

NASA Technical Reports Server (NTRS)

McGowan, Anna-Maria R.; Daly, Shanna; Baker, Wayne; Papalambros, panos; Seifert, Colleen

2013-01-01

This study investigates interdisciplinary interactions that take place during the research, development, and early conceptual design phases in the design of large-scale complex engineered systems (LaCES) such as aerospace vehicles. These interactions, that take place throughout a large engineering development organization, become the initial conditions of the systems engineering process that ultimately leads to the development of a viable system. This paper summarizes some of the challenges and opportunities regarding social and organizational issues that emerged from a qualitative study using ethnographic and survey data. The analysis reveals several socio-technical couplings between the engineered system and the organization that creates it. Survey respondents noted the importance of interdisciplinary interactions and their benefits to the engineered system as well as substantial challenges in interdisciplinary interactions. Noted benefits included enhanced knowledge and problem mitigation and noted obstacles centered on organizational and human dynamics. Findings suggest that addressing the social challenges may be a critical need in enabling interdisciplinary interactions

Key design elements of a data utility for national biosurveillance: event-driven architecture, caching, and Web service model.

PubMed

Tsui, Fu-Chiang; Espino, Jeremy U; Weng, Yan; Choudary, Arvinder; Su, Hoah-Der; Wagner, Michael M

2005-01-01

The National Retail Data Monitor (NRDM) has monitored over-the-counter (OTC) medication sales in the United States since December 2002. The NRDM collects data from over 18,600 retail stores and processes over 0.6 million sales records per day. This paper describes key architectural features that we have found necessary for a data utility component in a national biosurveillance system. These elements include event-driven architecture to provide analyses of data in near real time, multiple levels of caching to improve query response time, high availability through the use of clustered servers, scalable data storage through the use of storage area networks and a web-service function for interoperation with affiliated systems. The methods and architectural principles are relevant to the design of any production data utility for public health surveillance-systems that collect data from multiple sources in near real time for use by analytic programs and user interfaces that have substantial requirements for time-series data aggregated in multiple dimensions.

A systematic review of sensory-based treatments for children with disabilities.

PubMed

Barton, Erin E; Reichow, Brian; Schnitz, Alana; Smith, Isaac C; Sherlock, Daniel

2015-02-01

Sensory-based therapies are designed to address sensory processing difficulties by helping to organize and control the regulation of environmental sensory inputs. These treatments are increasingly popular, particularly with children with behavioral and developmental disabilities. However, empirical support for sensory-based treatments is limited. The purpose of this review was to conduct a comprehensive and methodologically sound evaluation of the efficacy of sensory-based treatments for children with disabilities. Methods for this review were registered with PROSPERO (CRD42012003243). Thirty studies involving 856 participants met our inclusion criteria and were included in this review. Considerable heterogeneity was noted across studies in implementation, measurement, and study rigor. The research on sensory-based treatments is limited due to insubstantial treatment outcomes, weak experimental designs, or high risk of bias. Although many people use and advocate for the use of sensory-based treatments and there is a substantial empirical literature on sensory-based treatments for children with disabilities, insufficient evidence exists to support their use. Copyright © 2014 Elsevier Ltd. All rights reserved.

Optimizing the early phase development of new analgesics by human pain biomarkers.

PubMed

Arendt-Nielsen, Lars; Hoeck, Hans Christian

2011-11-01

Human pain biomarkers are based on standardized acute activation of pain pathways/mechanisms and quantitative assessment of the evoked responses. This approach can be applied to healthy volunteers, to pain patients, and before and after pharmacological interventions to help understanding and profile the mode of action (proof-of-concept) of new and existing analgesic compounds. Standardized stimuli of different modalities can be applied to different tissues (multimodal and multi-tissue) for profiling analgesic compounds with respect to modulation of pain transduction, transmission, specific mechanisms and processing. This approach substantiates which specific compounds may work in particular clinical pain conditions. Human pain biomarkers can be translational and may bridge animal findings in clinical pain conditions, which in turn can provide new possibilities for designing more successful clinical trials. Biomarker based proof-of-concept drug studies in either volunteers or selected patient populations provide inexpensive, fast and reliable mechanism-based information about dose-efficacy relationships. This is important information in the early drug development phase and for designing large expensive clinical trials.

Structural Analysis Methods for Structural Health Management of Future Aerospace Vehicles

NASA Technical Reports Server (NTRS)

Tessler, Alexander

2007-01-01

Two finite element based computational methods, Smoothing Element Analysis (SEA) and the inverse Finite Element Method (iFEM), are reviewed, and examples of their use for structural health monitoring are discussed. Due to their versatility, robustness, and computational efficiency, the methods are well suited for real-time structural health monitoring of future space vehicles, large space structures, and habitats. The methods may be effectively employed to enable real-time processing of sensing information, specifically for identifying three-dimensional deformed structural shapes as well as the internal loads. In addition, they may be used in conjunction with evolutionary algorithms to design optimally distributed sensors. These computational tools have demonstrated substantial promise for utilization in future Structural Health Management (SHM) systems.

Factor structure of the Hooper Visual Organization Test: a cross-cultural replication and extension.

PubMed

Merten, Thomas

2005-01-01

To investigate construct validity of the Hooper Visual Organization Test (VOT), a principal-axis analysis was performed on the neuropsychological test results of 200 German-speaking neurological patients who received a comprehensive battery, encompassing tests of visuospatial functions, memory, attention, executive functions, naming ability, and vocabulary. A four-factor solution was obtained with substantial loadings of the VOT only on the first factor, interpreted as a global dimension of non-verbal cognitive functions. This factor loaded significantly on numerous measures of visuospatial processing and attention (with particularly high loadings on WAIS-R Block Design, Trails A and B, and Raven's Standard Progressive Matrices). The remaining three factors were interpreted as memory, verbal abilities (vocabulary), and a separate factor of naming abilities.

Outlook and Challenges of Perovskite Solar Cells toward Terawatt-Scale Photovoltaic Module Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Kai; Kim, Donghoe; Whitaker, James B

Rapid development of perovskite solar cells (PSCs) during the past several years has made this photovoltaic (PV) technology a serious contender for potential large-scale deployment on the terawatt scale in the PV market. To successfully transition PSC technology from the laboratory to industry scale, substantial efforts need to focus on scalable fabrication of high-performance perovskite modules with minimum negative environmental impact. Here, we provide an overview of the current research and our perspective regarding PSC technology toward future large-scale manufacturing and deployment. Several key challenges discussed are (1) a scalable process for large-area perovskite module fabrication; (2) less hazardous chemicalmore » routes for PSC fabrication; and (3) suitable perovskite module designs for different applications.« less

Digital Images on the DIME

NASA Technical Reports Server (NTRS)

2003-01-01

With NASA on its side, Positive Systems, Inc., of Whitefish, Montana, is veering away from the industry standards defined for producing and processing remotely sensed images. A top developer of imaging products for geographic information system (GIS) and computer-aided design (CAD) applications, Positive Systems is bucking traditional imaging concepts with a cost-effective and time-saving software tool called Digital Images Made Easy (DIME(trademark)). Like piecing a jigsaw puzzle together, DIME can integrate a series of raw aerial or satellite snapshots into a single, seamless panoramic image, known as a 'mosaic.' The 'mosaicked' images serve as useful backdrops to GIS maps - which typically consist of line drawings called 'vectors' - by allowing users to view a multidimensional map that provides substantially more geographic information.

A Topological Array Trigger for AGIS, the Advanced Gamma ray Imaging System

NASA Astrophysics Data System (ADS)

Krennrich, F.; Anderson, J.; Buckley, J.; Byrum, K.; Dawson, J.; Drake, G.; Haberichter, W.; Imran, A.; Krawczynski, H.; Kreps, A.; Schroedter, M.; Smith, A.

2008-12-01

Next generation ground based γ-ray observatories such as AGIS1 and CTA2 are expected to cover a 1 km2 area with 50-100 imaging atmospheric Cherenkov telescopes. The stereoscopic view ol air showers using multiple view points raises the possibility to use a topological array trigger that adds substantial flexibility, new background suppression capabilities and a reduced energy threshold. In this paper we report on the concept and technical implementation of a fast topological trigger system, that makes use of real time image processing of individual camera patterns and their combination in a stereoscopic array analysis. A prototype system is currently under construction and we discuss the design and hardware of this topological array trigger system.

A practical radial basis function equalizer.

PubMed

Lee, J; Beach, C; Tepedelenlioglu, N

1999-01-01

A radial basis function (RBF) equalizer design process has been developed in which the number of basis function centers used is substantially fewer than conventionally required. The reduction of centers is accomplished in two-steps. First an algorithm is used to select a reduced set of centers that lie close to the decision boundary. Then the centers in this reduced set are grouped, and an average position is chosen to represent each group. Channel order and delay, which are determining factors in setting the initial number of centers, are estimated from regression analysis. In simulation studies, an RBF equalizer with more than 2000-to-1 reduction in centers performed as well as the RBF equalizer without reduction in centers, and better than a conventional linear equalizer.

Monitoring for conservation

USGS Publications Warehouse

Nichols, J.D.; Williams, B.K.

2006-01-01

Human-mediated environmental changes have resulted in appropriate concern for the conservation of ecological systems and have led to the development of many ecological monitoring programs worldwide. Many programs that are identified with the purpose of `surveillance? represent an inefficient use of conservation funds and effort. Here, we revisit the 1964 paper by Platt and argue that his recommendations about the conduct of science are equally relevant to the conduct of ecological monitoring programs. In particular, we argue that monitoring should not be viewed as a stand-alone activity, but instead as a component of a larger process of either conservation-oriented science or management. Corresponding changes in monitoring focus and design would lead to substantial increases in the efficiency and usefulness of monitoring results in conservation.

Revised Point of Departure Design Options for Nuclear Thermal Propulsion

NASA Technical Reports Server (NTRS)

Fittje, James E.; Schnitzler, Bruce G.; Borowoski, Stanley

2015-01-01

Four Revised Point of Departure NTR Engines were Designed and Analyzed using MCNP and NESS. All Four Engines Have Thermodynamically Closed Cycles at Nominal Chamber Pressures. 111 kilonewton (25 kip-force) Cermet Design Required Dedicated Heater Elements to Close the Cycle. Cermet Based Designs had Slightly Higher TW Ratios, but Required Substantially More U-235. NERVA Derived Criticality Limited Engine Could Operate at Lower Power and Thrust Levels Compared to the Criticality Limited Cermet Design.

Dyes designed for high sensitivity detection of double-stranded DNA

DOEpatents

Glazer, Alexander N.; Benson, Scott C.

2000-01-01

Novel fluorescent dyes are provided, characterized by having a fluorophore joined to a cationic chain. The dyes are found to provide for high enhancement upon binding to nucleic acid and have strong binding affinities to the nucleic acid, as compared to the fluorophore without the polycationic chain. The dyes find use in detection of dsDNA in gel electrophoresis and solution at substantially higher sensitivities using substantially less dye.

Dyes designed for high sensitivity detection of double-stranded DNA

DOEpatents

Glazer, Alexander N.; Benson, Scott C.

1998-01-01

Novel fluorescent dyes are provided, characterized by having a fluorophore joined to a cationic chain. The dyes are found to provide for high enhancement upon binding to nucleic acid and have strong binding affinities to the nucleic acid, as compared to the fluorophore without the polycationic chain. The dyes find use in detection of dsDNA in gel electrophoresis and solution at substantially higher sensitivities using substantially less dye.

Paradigm shifts: using a participatory leadership process to redesign health systems.

PubMed

Saleeby, Erin; Holschneider, Christine H; Singhal, Rita

2014-12-01

Physicians have increasingly given up private practices to become members of, and key stakeholders in, large healthcare systems. These systems are currently transforming to meet the Triple Aim: guaranteeing the equitable provision of high-quality, evidence-based care at a reasonable cost. Participatory leadership is an organizational change theory that engages key stakeholders as architects in the transformation process. This review highlights the utility of this leadership strategy in designing care for women's health. Our blueprint describing participatory leadership theory in women's health systems change is discussed in three case studies, highlighting what we call the six Ps of participatory leadership: participants, principles, purpose, process, and power. The 'sixth P', product, can then be substantially influential in changing the paradigm of care. Obstetrics and gynecology is increasingly practiced in large health systems responsible for the health of populations. Innovations in clinical practice impact care at the level of the individual. In order for advances in clinical practice to reach broad populations of women, they must be integrated into a delivery system. Physician engagement in leadership during this time of system transformation is of critical importance.

Diabetes Prevention for Latino Youth: Unraveling the Intervention "Black Box".

PubMed

Shaibi, Gabriel Q; Konopken, Yolanda P; Nagle-Williams, Allison; McClain, Darya D; Castro, Felipe Gonzalez; Keller, Colleen S

2015-11-01

The translation of research findings into sustainable health promotion and disease prevention programs in community settings remains a challenge. This report describes the process of substantiating a community-developed diabetes prevention program for Latino youth through research. Included are design considerations, measurement strategies, and the context through which the project is culturally grounded for relevance and fit within a local community. The process included (1) refining the program to include salient, stakeholder-identified behavioral components; (2) refining the collaborative effort to embrace the capacity for facilitating relevant behavior change on targeted health-related outcomes to enhance intervention effectiveness; and (3) including the accurate assessment of intervention efficacy via precise assessment of diabetes-related health outcomes. We explain the process of collaborating with community partners to enhance the cultural relevance and sustainability of intervention effects on both individuals and communities. We discuss the rationale for empirical support for academic-community collaborations that function in both a "top-down" and a "bottom-up" manner to advance the science and practice of sustainable and efficacious community health promotion. © 2015 Society for Public Health Education.

Optimization of continuous and intermittent microwave extraction of pectin from banana peels.

PubMed

Swamy, Gabriela John; Muthukumarappan, Kasiviswanathan

2017-04-01

Continuous and intermittent microwave-assisted extractions were used to extract pectin from banana peels. Extraction parameters which were employed in the continuous process were microwave power (300-900W), time (100-300s), pH (1-3) and in the intermittent process were microwave power (300-900W), pulse ratio (0.5-1), pH (1-3). The independent factors were optimized with the Box-Behnken response surface design (BBD) (three factor three level) with the desirability function methodology. Results indicate that the independent factors have substantial effect on the pectin yield. Optimized solutions for highest pectin yield (2.18%) from banana peels were obtained with microwave power of 900W, time 100s and pH 3.00 in the continuous method while the intermittent process yielded the highest pectin content (2.58%) at microwave power of 900W, pulse ratio of 0.5 and pH of 3.00. The optimized conditions were validated and close agreement was observed with the validation experiment and predicted value. Copyright © 2016 Elsevier Ltd. All rights reserved.

Development of the University of Washington Biofuels and Biobased Chemicals Process Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gustafson, Richard

2014-02-04

The funding from this research grant enabled us to design and build a bioconversion steam explosion reactor and ancillary equipment such as a high pressure boiler and a fermenter to support the bioconversion process research. This equipment has been in constant use since its installation in 2012. Following are research projects that it has supported: • Investigation of novel chip production method in biofuels production • Investigation of biomass refining following steam explosion • Several studies on use of different biomass feedstocks • Investigation of biomass moisture content on pretreatment efficacy. • Development of novel instruments for biorefinery process controlmore » Having this equipment was also instrumental in the University of Washington receiving a $40 million grant from the US Department of Agriculture for biofuels development as well as several other smaller grants. The research that is being done with the equipment from this grant will facilitate the establishment of a biofuels industry in the Pacific Northwest and enable the University of Washington to launch a substantial biofuels and bio-based product research program.« less

Diatom Milking: A Review and New Approaches

PubMed Central

Vinayak, Vandana; Manoylov, Kalina M.; Gateau, Hélène; Blanckaert, Vincent; Hérault, Josiane; Pencréac’h, Gaëlle; Marchand, Justine; Gordon, Richard; Schoefs, Benoît

2015-01-01

The rise of human populations and the growth of cities contribute to the depletion of natural resources, increase their cost, and create potential climatic changes. To overcome difficulties in supplying populations and reducing the resource cost, a search for alternative pharmaceutical, nanotechnology, and energy sources has begun. Among the alternative sources, microalgae are the most promising because they use carbon dioxide (CO2) to produce biomass and/or valuable compounds. Once produced, the biomass is ordinarily harvested and processed (downstream program). Drying, grinding, and extraction steps are destructive to the microalgal biomass that then needs to be renewed. The extraction and purification processes generate organic wastes and require substantial energy inputs. Altogether, it is urgent to develop alternative downstream processes. Among the possibilities, milking invokes the concept that the extraction should not kill the algal cells. Therefore, it does not require growing the algae anew. In this review, we discuss research on milking of diatoms. The main themes are (a) development of alternative methods to extract and harvest high added value compounds; (b) design of photobioreactors; (c) biodiversity and (d) stress physiology, illustrated with original results dealing with oleaginous diatoms. PMID:25939034

Tigers on trails: occupancy modeling for cluster sampling.

PubMed

Hines, J E; Nichols, J D; Royle, J A; MacKenzie, D I; Gopalaswamy, A M; Kumar, N Samba; Karanth, K U

2010-07-01

Occupancy modeling focuses on inference about the distribution of organisms over space, using temporal or spatial replication to allow inference about the detection process. Inference based on spatial replication strictly requires that replicates be selected randomly and with replacement, but the importance of these design requirements is not well understood. This paper focuses on an increasingly popular sampling design based on spatial replicates that are not selected randomly and that are expected to exhibit Markovian dependence. We develop two new occupancy models for data collected under this sort of design, one based on an underlying Markov model for spatial dependence and the other based on a trap response model with Markovian detections. We then simulated data under the model for Markovian spatial dependence and fit the data to standard occupancy models and to the two new models. Bias of occupancy estimates was substantial for the standard models, smaller for the new trap response model, and negligible for the new spatial process model. We also fit these models to data from a large-scale tiger occupancy survey recently conducted in Karnataka State, southwestern India. In addition to providing evidence of a positive relationship between tiger occupancy and habitat, model selection statistics and estimates strongly supported the use of the model with Markovian spatial dependence. This new model provides another tool for the decomposition of the detection process, which is sometimes needed for proper estimation and which may also permit interesting biological inferences. In addition to designs employing spatial replication, we note the likely existence of temporal Markovian dependence in many designs using temporal replication. The models developed here will be useful either directly, or with minor extensions, for these designs as well. We believe that these new models represent important additions to the suite of modeling tools now available for occupancy estimation in conservation monitoring. More generally, this work represents a contribution to the topic of cluster sampling for situations in which there is a need for specific modeling (e.g., reflecting dependence) for the distribution of the variable(s) of interest among subunits.

Method for changing the cross section of a laser beam

DOEpatents

Sweatt, W.C.; Seppala, L.

1995-12-05

A technique is disclosed herein in which a circular optical beam, for example a copper vapor laser (CVL) beam, is converted to a beam having a profile other than circular, e.g. square or triangular. This is accomplished by utilizing a single optical mirror having a reflecting surface designed in accordance with a specifically derived formula in order to make the necessary transformation, without any substantial light loss and without changing substantially the intensity profile of the circular beam which has a substantially uniform intensity profile. In this way, the output beam can be readily directed into the dye cell of a dye laser. 4 figs.

Method for changing the cross section of a laser beam

DOEpatents

Sweatt, William C.; Seppala, Lynn

1995-01-01

A technique is disclosed herein in which a circular optical beam, for example a copper vapor laser (CVL) beam, is converted to a beam having a profile other than circular, e.g. square or triangular. This is accomplished by utilizing a single optical mirror having a reflecting surface designed in accordance with a specifically derived formula in order to make the necessary transformation, without any substantial light loss and without changing substantially the intensity profile of the circular beam which has a substantially uniform intensity profile. In this way, the output beam can be readily directed into the dye cell of a dye laser.

Beyond the dual pathway model: evidence for the dissociation of timing, inhibitory, and delay-related impairments in attention-deficit/hyperactivity disorder.

PubMed

Sonuga-Barke, Edmund; Bitsakou, Paraskevi; Thompson, Margaret

2010-04-01

The dual pathway model explains neuro-psychological heterogeneity in Attention Deficit/Hyperactivity Disorder (ADHD) in terms of dissociable cognitive and motivational deficits each affecting some but not other patients. We explore whether deficits in temporal processing might constitute a third dissociable neuropsychological component of ADHD. Nine tasks designed to tap three domains (inhibitory control, delay aversion and temporal processing) were administered to ADHD probands (n=71; ages 6 to 17 years), their siblings (n=71; 65 unaffected by ADHD) and a group of non-ADHD controls (n=50). IQ and working memory were measured. Temporal processing, inhibitory control and delay-related deficits represented independent neuropsychological components. ADHD children differed from controls on all factors. For ADHD patients, the co-occurrence of inhibitory, temporal processing and delay-related deficits was no greater than expected by chance with substantial groups of patients showing only one problem. Domain-specific patterns of familial co-segregation provided evidence for the validity of neuropsychological subgroupings. The current results illustrate the neuropsychological heterogeneity in ADHD and initial support for a triple pathway model. The findings need to be replicated in larger samples.

Heater Validation for the NEXT-C Hollow Cathodes

NASA Technical Reports Server (NTRS)

Verhey, Timothy R.; Soulas, George C.; Mackey, Jonathan Ar.

2017-01-01

Swaged cathode heaters whose design was successfully demonstrated under a prior flight project are to be provided by the NASA Glenn Research Center for the NEXT-C ion thruster being fabricated by Aerojet Rocketdyne. Extensive requalification activities were performed to validate process controls that had to be re-established or revised because systemic changes prevented reuse of the past approaches. A development batch of heaters was successfully fabricated based on the new process controls. Acceptance and cyclic life testing of multiple discharge and neutralizer sized heaters extracted from the development batch was initiated in August, 2016, with the last heater completing testing in April, 2017. Cyclic life testing results substantially exceeded the NEXT-C thruster requirement as well as all past experience for GRC fabricated units. The heaters demonstrated ultimate cyclic life capability of 19050 to 33500 cycles. A qualification batch of heaters is now being fabricated using the finalized process controls. A set of six heaters will be acceptance and cyclic tested to verify conformance to the behavior observed with the development heaters. The heaters for flight use will be then be provided to the contractor. This paper summarizes the fabrication process control activities and the acceptance and life testing of the development heater units.

Effective Process Design for the Production of HIC-Resistant Linepipe Steels

NASA Astrophysics Data System (ADS)

Nieto, J.; Elías, T.; López, G.; Campos, G.; López, F.; Garcia, R.; De, Amar K.

2013-09-01

Production of slabs for sour service applications requires stringent control in slab internal quality and secondary processing so as to guarantee resistance against hydrogen-induced cracking (HIC). ArcelorMittal Steelmaking facility at Lazaro Cardenas, Mexico had recently implemented key steelmaking and casting processing technologies for production of sound, centerline free slabs for catering to the growing API Linepipe and off-shore market for sour service applications. State-of-the-art steelmaking with use of residual-free Direct-reduced Iron and continuous casting facilities with dynamic soft reduction were introduced for the production of slabs with ultra clean centerline. Introduction of controlled cooling of slabs for atomic hydrogen control well below 2 ppm has enabled production of slabs suitable for excellent HIC-resistant plate processing. Substantial tonnages of slabs were produced for production of API X52-X65 grade plates and pipes for sour service. Stringent quality control at each stage of steelmaking, casting, and slab inspection ensured slabs with excellent internal quality suitable for HIC resistance to be guaranteed in final product (Plates & Pipes). Details of production steps which resulted in successful HIC-resistant slab production have been described in this article.

Challenges to fair decision-making processes in the context of health care services: a qualitative assessment from Tanzania

PubMed Central

2012-01-01

Background Fair processes in decision making need the involvement of stakeholders who can discuss issues and reach an agreement based on reasons that are justifiable and appropriate in meeting people’s needs. In Tanzania, the policy of decentralization and the health sector reform place an emphasis on community participation in making decisions in health care. However, aspects that can influence an individual’s opportunity to be listened to and to contribute to discussion have been researched to a very limited extent in low-income settings. The objective of this study was to explore challenges to fair decision-making processes in health care services with a special focus on the potential influence of gender, wealth, ethnicity and education. We draw on the principle of fairness as outlined in the deliberative democratic theory. Methods The study was carried out in the Mbarali District of Tanzania. A qualitative study design was used. In-depth interviews and focus group discussion were conducted among members of the district health team, local government officials, health care providers and community members. Informal discussion on the topics was also of substantial value. Results The study findings indicate a substantial influence of gender, wealth, ethnicity and education on health care decision-making processes. Men, wealthy individuals, members of strong ethnic groups and highly educated individuals had greater influence. Opinions varied among the study informants as to whether such differences should be considered fair. The differences in levels of influence emerged most clearly at the community level, and were largely perceived as legitimate. Conclusions Existing challenges related to individuals’ influence of decision making processes in health care need to be addressed if greater participation is desired. There is a need for increased advocacy and a strengthening of responsive practices with an emphasis on the right of all individuals to participate in decision-making processes. This simultaneously implies an emphasis on assuring the distribution of information, training and education so that individuals can participate fully in informed decision making. PMID:22676204

Autohydrolysis Pretreatment of Lignocellulosic Biomass for Bioethanol Production

NASA Astrophysics Data System (ADS)

Han, Qiang

Autohydrolysis, a simple and environmental friendly process, has long been studied but often abandoned as a financially viable pretreatment for bioethanol production due to the low yields of fermentable sugars at economic enzyme dosages. The introduction of mechanical refining can generate substantial improvements for autohydrolysis process, making it an attractive pretreatment technology for bioethanol commercialization. In this study, several lignocellulosic biomass including wheat straw, switchgrass, corn stover, waste wheat straw have been subjected to autohydrolysis pretreatment followed by mechanical refining to evaluate the total sugar recovery at affordable enzyme dosages. Encouraging results have been found that using autohydrolysis plus refining strategy, the total sugar recovery of most feedstock can be as high as 76% at 4 FPU/g enzymes dosages. The mechanical refining contributed to the improvement of enzymatic sugar yield by as much as 30%. Three non-woody biomass (sugarcane bagasse, wheat straw, and switchgrass) and three woody biomass (maple, sweet gum, and nitens) have been subjected to autohydrolysis pretreatment to acquire a fundamental understanding of biomass characteristics that affect the autohydrolysis and the following enzymatic hydrolysis. It is of interest to note that the nonwoody biomass went through substantial delignification during autohydrolysis compared to woody biomass due to a significant amount of p-coumaric acid and ferulic acid. It has been found that hardwood which has a higher S/V ratio in the lignin structure tends to have a higher total sugar recovery from autohydrolysis pretreatment. The economics of bioethanol production from autohydrolysis of different feedstocks have been investigated. Regardless of different feedstocks, in the conventional design, producing bioethanol and co-producing steam and power, the minimum ethanol revenues (MER) required to generate a 12% internal rate of return (IRR) are high enough to discourage investors due to the high capital investment relative to low US ethanol price. Nevertheless, the economics of autohydrolysis can be substantially improved by upgrading the value of unhydrolyzed residues, such as the fuel pellets. Moreover, the utilization of proven technology and equipment renders autohydrolysis adaptable to pulp and paper industrial. Attractive economics have been found when autohydrolysis based bioethanol plant is co-located to a pulp and paper mill or the distressed pulp and paper mill is being repurposed to produce bioethanol. An alternative to autohydrolysis combined with refining, thermomechanical pulping (TMP) process has been evaluated using corn stover as the feedstock. A significant low solids yield after the pretreatment process has been observed due to the harsh condition operated and the limitation of lab equipment. But the TMP process has great potential to be employed as a pretreatment for bioethanol production in an industrial scale if the process is optimized.

Teaching Insect Retinal Physiology with Newly Designed, Inexpensive Micromanipulators

ERIC Educational Resources Information Center

Krans, Jacob; Gilbert, Cole; Hoy, Ron

2006-01-01

In this article, we detail how to produce two inexpensive micromanipulators that offer high precision (approximately 25 micrometers) along a single axis of movement. The more expensive of the designs provides improved versatility along multiple axes. Both manipulators offer substantial savings over commercially available micromanipulators with…

48 CFR 252.225-7017 - Photovoltaic Devices.

Code of Federal Regulations, 2013 CFR

2013-10-01

... substantially transformed outside of a Caribbean Basin country. Designated country means— (i) A World Trade..., Sweden, Switzerland, Taiwan (known in the World Trade Organization as “the Separate Customs Territory of..., qualifying country, or designated country photovoltaic devices. (End of clause) [76 FR 78861, Dec. 20, 2011...

The conditional power of randomization tests for single-case effect sizes in designs with randomized treatment order: A Monte Carlo simulation study.

PubMed

Michiels, Bart; Heyvaert, Mieke; Onghena, Patrick

2018-04-01

The conditional power (CP) of the randomization test (RT) was investigated in a simulation study in which three different single-case effect size (ES) measures were used as the test statistics: the mean difference (MD), the percentage of nonoverlapping data (PND), and the nonoverlap of all pairs (NAP). Furthermore, we studied the effect of the experimental design on the RT's CP for three different single-case designs with rapid treatment alternation: the completely randomized design (CRD), the randomized block design (RBD), and the restricted randomized alternation design (RRAD). As a third goal, we evaluated the CP of the RT for three types of simulated data: data generated from a standard normal distribution, data generated from a uniform distribution, and data generated from a first-order autoregressive Gaussian process. The results showed that the MD and NAP perform very similarly in terms of CP, whereas the PND performs substantially worse. Furthermore, the RRAD yielded marginally higher power in the RT, followed by the CRD and then the RBD. Finally, the power of the RT was almost unaffected by the type of the simulated data. On the basis of the results of the simulation study, we recommend at least 20 measurement occasions for single-case designs with a randomized treatment order that are to be evaluated with an RT using a 5% significance level. Furthermore, we do not recommend use of the PND, because of its low power in the RT.

Chitosan-palmitic acid based polymeric micelles as promising carrier for circumventing pharmacokinetic and drug delivery concerns of tamoxifen.

PubMed

Thotakura, Nagarani; Dadarwal, Mukesh; Kumar, Rajendra; Singh, Bhupinder; Sharma, Gajanand; Kumar, Pramod; Katare, Om Prakash; Raza, Kaisar

2017-09-01

Being a BCS class II drug and a good substrate for microsomal enzymes, tamoxifen (TAM) offers a scope for research owing to poor aqueous solubility and compromised bioavailability. The present study designs a novel copolymer derived from palmitic acid and chitosan, and evaluate the derived TAM-loaded micelles for various delivery attributes. The nanometric micellar carriers not only substantially loaded the drug, but also controlled the rate of release of TAM. The designed nanocarrier significantly enhanced the cytotoxicity of TAM on MCF-7 cancer cells. The developed system was designed for intravenous route and was observed to be substantially haemo-compatible with an enhancement of approx. 5 times in AUC vis-a-vis plain drug. The findings employing new polymer-based carrier are promising in nature for the better delivery of similar drugs. Copyright © 2017 Elsevier B.V. All rights reserved.

12 CFR 303.22 - Processing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Insurance § 303.22 Processing. (a) Expedited processing for proposed institutions. (1) An application for... depository institutions. The FDIC may remove an application from expedited processing for any of the reasons... application within 60 days of receipt of a substantially complete application or 5 days after the expiration...

Process and apparatus for obtaining silicon from fluosilicic acid

DOEpatents

Sanjurjo, Angel

1988-06-28

Process and apparatus for producing low cost, high purity solar grade silicon ingots in single crystal or quasi single crystal ingot form in a substantially continuous operation in a two stage reactor starting with sodium fluosilicate and a metal more electropositive than silicon (preferably sodium) in separate compartments having easy vapor transport therebetween and thermally decomposing the sodium fluosilicate to cause formation of substantially pure silicon and a metal fluoride which may be continuously separated in the melt and silicon may be directly and continuously cast from the melt.

Spatial and temporal variance in fatty acid and stable isotope signatures across trophic levels in large river systems

USGS Publications Warehouse

Fritts, Andrea; Knights, Brent C.; Lafrancois, Toben D.; Bartsch, Lynn; Vallazza, Jon; Bartsch, Michelle; Richardson, William B.; Karns, Byron N.; Bailey, Sean; Kreiling, Rebecca

2018-01-01

Fatty acid and stable isotope signatures allow researchers to better understand food webs, food sources, and trophic relationships. Research in marine and lentic systems has indicated that the variance of these biomarkers can exhibit substantial differences across spatial and temporal scales, but this type of analysis has not been completed for large river systems. Our objectives were to evaluate variance structures for fatty acids and stable isotopes (i.e. δ13C and δ15N) of seston, threeridge mussels, hydropsychid caddisflies, gizzard shad, and bluegill across spatial scales (10s-100s km) in large rivers of the Upper Mississippi River Basin, USA that were sampled annually for two years, and to evaluate the implications of this variance on the design and interpretation of trophic studies. The highest variance for both isotopes was present at the largest spatial scale for all taxa (except seston δ15N) indicating that these isotopic signatures are responding to factors at a larger geographic level rather than being influenced by local-scale alterations. Conversely, the highest variance for fatty acids was present at the smallest spatial scale (i.e. among individuals) for all taxa except caddisflies, indicating that the physiological and metabolic processes that influence fatty acid profiles can differ substantially between individuals at a given site. Our results highlight the need to consider the spatial partitioning of variance during sample design and analysis, as some taxa may not be suitable to assess ecological questions at larger spatial scales.

Mechanical performance of cervical intervertebral body fusion devices: A systematic analysis of data submitted to the Food and Drug Administration.

PubMed

Peck, Jonathan H; Sing, David C; Nagaraja, Srinidhi; Peck, Deepa G; Lotz, Jeffrey C; Dmitriev, Anton E

2017-03-21

Cervical intervertebral body fusion devices (IBFDs) are utilized to provide stability while fusion occurs in patients with cervical pathology. For a manufacturer to market a new cervical IBFD in the United States, substantial equivalence to a cervical IBFD previously cleared by FDA must be established through the 510(k) regulatory pathway. Mechanical performance data are typically provided as part of the 510(k) process for IBFDs. We reviewed all Traditional 510(k) submissions for cervical IBFDs deemed substantially equivalent and cleared for marketing from 2007 through 2014. To reduce sources of variability in test methods and results, analysis was restricted to cervical IBFD designs without integrated fixation, coatings, or expandable features. Mechanical testing reports were analyzed and results were aggregated for seven commonly performed tests (static and dynamic axial compression, compression-shear, and torsion testing per ASTM F2077, and subsidence testing per ASTM F2267), and percentile distributions of performance measurements were calculated. Eighty-three (83) submissions met the criteria for inclusion in this analysis. The median device yield strength was 10,117N for static axial compression, 3680N for static compression-shear, and 8.6Nm for static torsion. Median runout load was 2600N for dynamic axial compression, 1400N for dynamic compression-shear, and ±1.5Nm for dynamic torsion. In subsidence testing, median block stiffness (Kp) was 424N/mm. The mechanical performance data presented here will aid in the development of future cervical IBFDs by providing a means for comparison for design verification purposes. Published by Elsevier Ltd.