Science.gov

Sample records for processing acm sigarch

  1. Use of composable solvers to represent multiphysics hydrologic and thermal processes in the ACME Land Model

    NASA Astrophysics Data System (ADS)

    Bisht, G.; Riley, W. J.

    2016-12-01

    Land surface models (LSMs), which are key components of Earth System Models (ESMs), simulate mass, energy, and nutrient cycles at the surface of the Earth. LSMs are routinely used to study the impact of human activities via land-cover change and increasing CO2 emissions on global climate. Over recent decades, there has been a tremendous growth in the number and complexity of processes incorporated in current generation LSMs. Traditionally, the various physics formulations in LSMs are solved as loosely coupled system of equations, but the importance of solving fully coupled multiphysics problems (e.g., soil-plant-atmosphere continuum, conservation of mass-energy in soil, etc.) is now well recognized. In this work, we develop a framework for solving tightly coupled multi physics problems (MPP). Our framework is built on top of the Portable, Extensible Toolkit for Scientific Computation's (PETSc's) multi-physics coupling capability (DMComposite). One of the main advantages of the MPP framework is the reuse of existing code when adding support for new physics formulations that are solved as a single fully coupled model. Numerical results from a range of multiphysics land surface process representations integrated in the ACME Land Model (ALM) are presented.

  2. Acme jumper pipe

    SciTech Connect

    Medved, P.; Thomas, H.

    1995-09-01

    Acme Steel had operated the larry car with an attached jumper pipe since 1977. Acme had been able to meet the State Implementation Plan. With the advent of the Clean Air Act, Acme did not feel it could meet these new standards without some modifications to the jumper pipe system. Several drop sleeve modifications and numerous boot seal materials and configurations were tested that resulted in limited success in improving the boot seal life. After these modifications, Acme`s testing revealed it could meet the Clean Air Act standards, but it would be cost prohibitive to continue to operate in this manner. Following extensive investigation, Acme decided to install an off-car jumper pipe system which uses a traveling U-tube for connecting to the assist oven through an additional hole in each oven roof. Temperature related failures of drop sleeve seals were eliminated. The off-car jumper pipe is a more efficient gas connection to the assist oven and enables Acme to meet the Clean Air Act charging requirements in a cost effective manner.

  3. ACM TOMS replicated computational results initiative

    DOE PAGES

    Heroux, Michael Allen

    2015-06-03

    In this study, the scientific community relies on the peer review process for assuring the quality of published material, the goal of which is to build a body of work we can trust. Computational journals such as The ACM Transactions on Mathematical Software (TOMS) use this process for rigorously promoting the clarity and completeness of content, and citation of prior work. At the same time, it is unusual to independently confirm computational results.

  4. ACM TOMS replicated computational results initiative

    SciTech Connect

    Heroux, Michael Allen

    2015-06-03

    In this study, the scientific community relies on the peer review process for assuring the quality of published material, the goal of which is to build a body of work we can trust. Computational journals such as The ACM Transactions on Mathematical Software (TOMS) use this process for rigorously promoting the clarity and completeness of content, and citation of prior work. At the same time, it is unusual to independently confirm computational results.

  5. ACME-III and ACME-IV Final Campaign Reports

    SciTech Connect

    Biraud, S. C.

    2016-01-01

    The goals of the Atmospheric Radiation Measurement (ARM) Climate Research Facility’s third and fourth Airborne Carbon Measurements (ACME) field campaigns, ACME-III and ACME-IV, are: 1) to measure and model the exchange of CO2, water vapor, and other greenhouse gases by the natural, agricultural, and industrial ecosystems of the Southern Great Plains (SGP) region; 2) to develop quantitative approaches to relate these local fluxes to the concentration of greenhouse gases measured at the Central Facility tower and in the atmospheric column above the ARM SGP Central Facility, 3) to develop and test bottom-up measurement and modeling approaches to estimate regional scale carbon balances, and 4) to develop and test inverse modeling approaches to estimate regional scale carbon balance and anthropogenic sources over continental regions. Regular soundings of the atmosphere from near the surface into the mid-troposphere are essential for this research.

  6. How to recycle asbestos containing materials (ACM)

    SciTech Connect

    Jantzen, C.M.

    2000-04-11

    The current disposal of asbestos containing materials (ACM) in the private sector consists of sealing asbestos wetted with water in plastic for safe transportation and burial in regulated land fills. This disposal methodology requires large disposal volumes especially for asbestos covered pipe and asbestos/fiberglass adhering to metal framework, e.g. filters. This wrap and bury technology precludes recycle of the asbestos, the pipe and/or the metal frameworks. Safe disposal of ACM at U.S. Department of Energy (DOE) sites, likewise, requires large disposal volumes in landfills for non-radioactive ACM and large disposal volumes in radioactive burial grounds for radioactive and suspect contaminated ACM. The availability of regulated disposal sites is rapidly diminishing causing recycle to be a more attractive option. Asbestos adhering to metal (e.g., pipes) can be recycled by safely removing the asbestos from the metal in a patented hot caustic bath which prevents airborne contamination /inhalation of asbestos fibers. The dissolution residue (caustic and asbestos) can be wet slurry fed to a melter and vitrified into a glass or glass-ceramic. Palex glasses, which are commercially manufactured, are shown to be preferred over conventional borosilicate glasses. The Palex glasses are alkali magnesium silicate glasses derived by substituting MgO for B{sub 2}O{sub 3} in borosilicate type glasses. Palex glasses are very tolerant of the high MgO and high CaO content of the fillers used in forming asbestos coverings for pipes and found in boiler lashing, e.g., hydromagnesite (3MgCO{sub 3} Mg(OH){sub 2} 3H{sub 2}O) and plaster of paris, gypsum (CaSO{sub 4}). The high temperate of the vitrification process destroys the asbestos fibers and renders the asbestos non-hazardous, e.g., a glass or glass-ceramic. In this manner the glass or glass-ceramic produced can be recycled, e.g., glassphalt or glasscrete, as can the clean metal pipe or metal framework.

  7. ACME: A Basis for Architecture Exchange

    DTIC Science & Technology

    2003-12-01

    representation of Acme in an internal study, which later matured to be known as ADML (see http://xml.coverpages.org/adml.html). David Wile...interchange medium to enable inter-ADL tool use. The growth of xAcme and ADML indicates significant web usage. • Provide a base level ADL to be

  8. Asbestos-Containing Materials (ACM) and Demolition

    EPA Pesticide Factsheets

    There are specific federal regulatory requirements that require the identification of asbestos-containing materials (ACM) in many of the residential buildings that are being demolished or renovated by a municipality.

  9. Quark ACM with topologically generated gluon mass

    NASA Astrophysics Data System (ADS)

    Choudhury, Ishita Dutta; Lahiri, Amitabha

    2016-03-01

    We investigate the effect of a small, gauge-invariant mass of the gluon on the anomalous chromomagnetic moment (ACM) of quarks by perturbative calculations at one-loop level. The mass of the gluon is taken to have been generated via a topological mass generation mechanism, in which the gluon acquires a mass through its interaction with an antisymmetric tensor field Bμν. For a small gluon mass ( < 10 MeV), we calculate the ACM at momentum transfer q2 = -M Z2. We compare those with the ACM calculated for the gluon mass arising from a Proca mass term. We find that the ACM of up, down, strange and charm quarks vary significantly with the gluon mass, while the ACM of top and bottom quarks show negligible gluon mass dependence. The mechanism of gluon mass generation is most important for the strange quarks ACM, but not so much for the other quarks. We also show the results at q2 = -m t2. We find that the dependence on gluon mass at q2 = -m t2 is much less than at q2 = -M Z2 for all quarks.

  10. Additive Construction with Mobile Emplacement (ACME)

    NASA Technical Reports Server (NTRS)

    Vickers, John

    2015-01-01

    The Additive Construction with Mobile Emplacement (ACME) project is developing technology to build structures on planetary surfaces using in-situ resources. The project focuses on the construction of both 2D (landing pads, roads, and structure foundations) and 3D (habitats, garages, radiation shelters, and other structures) infrastructure needs for planetary surface missions. The ACME project seeks to raise the Technology Readiness Level (TRL) of two components needed for planetary surface habitation and exploration: 3D additive construction (e.g., contour crafting), and excavation and handling technologies (to effectively and continuously produce in-situ feedstock). Additionally, the ACME project supports the research and development of new materials for planetary surface construction, with the goal of reducing the amount of material to be launched from Earth.

  11. Porcine bladder acellular matrix (ACM): protein expression, mechanical properties.

    PubMed

    Farhat, Walid A; Chen, Jun; Haig, Jennifer; Antoon, Roula; Litman, Jessica; Sherman, Christopher; Derwin, Kathleen; Yeger, Herman

    2008-06-01

    Experimentally, porcine bladder acellular matrix (ACM) that mimics extracellular matrix has excellent potential as a bladder substitute. Herein we investigated the spatial localization and expression of different key cellular and extracellular proteins in the ACM; furthermore, we evaluated the inherent mechanical properties of the resultant ACM prior to implantation. Using a proprietary decellularization method, the DNA contents in both ACM and normal bladder were measured; in addition we used immunohistochemistry and western blots to quantify and localize the different cellular and extracellular components, and finally the mechanical testing was performed using a uniaxial mechanical testing machine. The mean DNA content in the ACM was significantly lower in the ACM compared to the bladder. Furthermore, the immunohistochemical and western blot analyses showed that collagen I and IV were preserved in the ACM, but possibly denatured collagen III in the ACM. Furthermore, elastin, laminin and fibronectin were mildly reduced in the ACM. Although the ACM did not exhibit nucleated cells, residual cellular components (actin, myosin, vimentin and others) were still present. There was, on the other hand, no significant difference in the mean stiffness between the ACM and the bladder. Although our decellularization method is effective in removing nuclear material from the bladder while maintaining its inherent mechanical properties, further work is mandatory to determine whether these residual DNA and cellular remnants would lead to any immune reaction, or if the mechanical properties of the ACM are preserved upon implantation and cellularization.

  12. Porosity of porcine bladder acellular matrix: impact of ACM thickness.

    PubMed

    Farhat, Walid; Chen, Jun; Erdeljan, Petar; Shemtov, Oren; Courtman, David; Khoury, Antoine; Yeger, Herman

    2003-12-01

    The objectives of this study are to examine the porosity of bladder acellular matrix (ACM) using deionized (DI) water as the model fluid and dextran as the indicator macromolecule, and to correlate the porosity to the ACM thickness. Porcine urinary bladders from pigs weighing 20-50 kg were sequentially extracted in detergent containing solutions, and to modify the ACM thickness, stretched bladders were acellularized in the same manner. Luminal and abluminal ACM specimens were subjected to fixed static DI water pressure (10 cm); and water passing through the specimens was collected at specific time interval. While for the macromolecule porosity testing, the diffusion rate and direction of 10,000 MW fluoroescein-labeled dextrans across the ACM specimens mounted in Ussing's chambers were measured. Both experiments were repeated on the thin stretched ACM. In both ACM types, the fluid porosity in both directions did not decrease with increased test duration (3 h); in addition, the abluminal surface was more porous to fluid than the luminal surface. On the other hand, when comparing thin to thick ACM, the porosity in either direction was higher in the thick ACM. Macromolecule porosity, as measured by absorbance, was higher for the abluminal thick ACM than the luminal side, but this characteristic was reversed in the thin ACM. Comparing thin to thick ACM, the luminal side in the thin ACM was more porous to dextran than in the thick ACM, but this characteristic was reversed for the abluminal side. The porcine bladder ACM possesses directional porosity and acellularizing stretched urinary bladders may increase structural density and alter fluid and macromolecule porosity.

  13. Air Traffic Complexity Measurement Environment (ACME): Software User's Guide

    NASA Technical Reports Server (NTRS)

    1996-01-01

    A user's guide for the Air Traffic Complexity Measurement Environment (ACME) software is presented. The ACME consists of two major components, a complexity analysis tool and user interface. The Complexity Analysis Tool (CAT) analyzes complexity off-line, producing data files which may be examined interactively via the Complexity Data Analysis Tool (CDAT). The Complexity Analysis Tool is composed of three independently executing processes that communicate via PVM (Parallel Virtual Machine) and Unix sockets. The Runtime Data Management and Control process (RUNDMC) extracts flight plan and track information from a SAR input file, and sends the information to GARP (Generate Aircraft Routes Process) and CAT (Complexity Analysis Task). GARP in turn generates aircraft trajectories, which are utilized by CAT to calculate sector complexity. CAT writes flight plan, track and complexity data to an output file, which can be examined interactively. The Complexity Data Analysis Tool (CDAT) provides an interactive graphic environment for examining the complexity data produced by the Complexity Analysis Tool (CAT). CDAT can also play back track data extracted from System Analysis Recording (SAR) tapes. The CDAT user interface consists of a primary window, a controls window, and miscellaneous pop-ups. Aircraft track and position data is displayed in the main viewing area of the primary window. The controls window contains miscellaneous control and display items. Complexity data is displayed in pop-up windows. CDAT plays back sector complexity and aircraft track and position data as a function of time. Controls are provided to start and stop playback, adjust the playback rate, and reposition the display to a specified time.

  14. An audience-channel-message-evaluation (ACME) framework for health communication campaigns.

    PubMed

    Noar, Seth M

    2012-07-01

    Recent reviews of the literature have indicated that a number of health communication campaigns continue to fail to adhere to principles of effective campaign design. The lack of an integrated, organizing framework for the design, implementation, and evaluation of health communication campaigns may contribute to this state of affairs. The current article introduces an audience-channel-message-evaluation (ACME) framework that organizes the major principles of health campaign design, implementation, and evaluation. ACME also explicates the relationships and linkages between the varying principles. Insights from ACME include the following: The choice of audience segment(s) to focus on in a campaign affects all other campaign design choices, including message strategy and channel/component options. Although channel selection influences options for message design, choice of message design also influences channel options. Evaluation should not be thought of as a separate activity, but rather should be infused and integrated throughout the campaign design and implementation process, including formative, process, and outcome evaluation activities. Overall, health communication campaigns that adhere to this integrated set of principles of effective campaign design will have a greater chance of success than those using principles idiosyncratically. These design, implementation, and evaluation principles are embodied in the ACME framework.

  15. AcmD, a Homolog of the Major Autolysin AcmA of Lactococcus lactis, Binds to the Cell Wall and Contributes to Cell Separation and Autolysis

    PubMed Central

    Visweswaran, Ganesh Ram R.; Steen, Anton; Leenhouts, Kees; Szeliga, Monika; Ruban, Beata; Hesseling-Meinders, Anne; Dijkstra, Bauke W.; Kuipers, Oscar P.; Kok, Jan; Buist, Girbe

    2013-01-01

    Lactococcus lactis expresses the homologous glucosaminidases AcmB, AcmC, AcmA and AcmD. The latter two have three C-terminal LysM repeats for peptidoglycan binding. AcmD has much shorter intervening sequences separating the LysM repeats and a lower iso-electric point (4.3) than AcmA (10.3). Under standard laboratory conditions AcmD was mainly secreted into the culture supernatant. An L. lactis acmAacmD double mutant formed longer chains than the acmA single mutant, indicating that AcmD contributes to cell separation. This phenotype could be complemented by plasmid-encoded expression of AcmD in the double mutant. No clear difference in cellular lysis and protein secretion was observed between both mutants. Nevertheless, overexpression of AcmD resulted in increased autolysis when AcmA was present (as in the wild type strain) or when AcmA was added to the culture medium of an AcmA-minus strain. Possibly, AcmD is mainly active within the cell wall, at places where proper conditions are present for its binding and catalytic activity. Various fusion proteins carrying either the three LysM repeats of AcmA or AcmD were used to study and compare their cell wall binding characteristics. Whereas binding of the LysM domain of AcmA took place at pHs ranging from 4 to 8, LysM domain of AcmD seems to bind strongest at pH 4. PMID:23951292

  16. Acme Foundry, Inc. - Clean Water Act Public Notice

    EPA Pesticide Factsheets

    The EPA is providing notice of a proposed Administrative Penalty Assessment against Acme Foundry, Inc., for alleged violations at its facility located at 1502 South Spruce Street, Coffeyville, Kansas 67337

  17. Pomegranate MR images analysis using ACM and FCM algorithms

    NASA Astrophysics Data System (ADS)

    Morad, Ghobad; Shamsi, Mousa; Sedaaghi, M. H.; Alsharif, M. R.

    2011-10-01

    Segmentation of an image plays an important role in image processing applications. In this paper segmentation of pomegranate magnetic resonance (MR) images has been explored. Pomegranate has healthy nutritional and medicinal properties for which the maturity indices and quality of internal tissues play an important role in the sorting process in which the admissible determination of features mentioned above cannot be easily achieved by human operator. Seeds and soft tissues are the main internal components of pomegranate. For research purposes, such as non-destructive investigation, in order to determine the ripening index and the percentage of seeds in growth period, segmentation of the internal structures should be performed as exactly as possible. In this paper, we present an automatic algorithm to segment the internal structure of pomegranate. Since its intensity of stem and calyx is close to the internal tissues, the stem and calyx pixels are usually labeled to the internal tissues by segmentation algorithm. To solve this problem, first, the fruit shape is extracted from its background using active contour model (ACM). Then stem and calyx are removed using morphological filters. Finally the image is segmented by fuzzy c-means (FCM). The experimental results represent an accuracy of 95.91% in the presence of stem and calyx, while the accuracy of segmentation increases to 97.53% when stem and calyx are first removed by morphological filters.

  18. In-situ Data Analysis Framework for ACME Land Simulations

    NASA Astrophysics Data System (ADS)

    Wang, D.; Yao, C.; Jia, Y.; Steed, C.; Atchley, S.

    2015-12-01

    The realistic representation of key biogeophysical and biogeochemical functions is the fundamental of process-based ecosystem models. Investigating the behavior of those ecosystem functions within real-time model simulation can be a very challenging due to the complex of both model and software structure of an environmental model, such as the Accelerated Climate Model for Energy (ACME) Land Model (ALM). In this research, author will describe the urgent needs and challenges for in-situ data analysis for ALM simulations, and layouts our methods/strategies to meet these challenges. Specifically, an in-situ data analysis framework is designed to allow users interactively observe the biogeophyical and biogeochemical process during ALM simulation. There are two key components in this framework, automatically instrumented ecosystem simulation, in-situ data communication and large-scale data exploratory toolkit. This effort is developed by leveraging several active projects, including scientific unit testing platform, common communication interface and extreme-scale data exploratory toolkit. Authors believe that, based on advanced computing technologies, such as compiler-based software system analysis, automatic code instrumentation, and in-memory data transport, this software system provides not only much needed capability for real-time observation and in-situ data analytics for environmental model simulation, but also the potentials for in-situ model behavior adjustment via simulation steering.

  19. ARM Airborne Carbon Measurements VI (ACME VI) Science Plan

    SciTech Connect

    Biraud, S

    2015-12-01

    From October 1 through September 30, 2016, the Atmospheric Radiation Measurement (ARM) Aerial Facility will deploy the Cessna 206 aircraft over the Southern Great Plains (SGP) site, collecting observations of trace-gas mixing ratios over the ARM’s SGP facility. The aircraft payload includes two Atmospheric Observing Systems, Inc., analyzers for continuous measurements of CO2 and a 12-flask sampler for analysis of carbon cycle gases (CO2, CO, CH4, N2O, 13CO2, 14CO2, carbonyl sulfide, and trace hydrocarbon species, including ethane). The aircraft payload also includes instrumentation for solar/infrared radiation measurements. This research is supported by the U.S. Department of Energy’s ARM Climate Research Facility and Terrestrial Ecosystem Science Program and builds upon previous ARM Airborne Carbon Measurements (ARM-ACME) missions. The goal of these measurements is to improve understanding of 1) the carbon exchange at the SGP site, 2) how CO2 and associated water and energy fluxes influence radiative forcing, convective processes and CO2 concentrations over the SGP site, and 3) how greenhouse gases are transported on continental scales.

  20. Proposed Expansion of Acme Landfill Operations.

    DTIC Science & Technology

    1982-08-01

    plastic beverage bottles, cardboard, wood, yardwastes, textiles , rubber, and leather. In addition to traditional activities, a central processing center...from food and garden wastes), a considerable portion of the leachate strength may be attributable to the textiles , rubber, leather, wood, paper, and...poisoning); mosquitos which may carry viral diseases such as encephalitis, malaria, and yellow fever; rodents which are carriers of enteric and other

  1. Prevalence and genetic diversity of arginine catabolic mobile element (ACME) in clinical isolates of coagulase-negative staphylococci: identification of ACME type I variants in Staphylococcus epidermidis.

    PubMed

    Onishi, Mayumi; Urushibara, Noriko; Kawaguchiya, Mitsuyo; Ghosh, Souvik; Shinagawa, Masaaki; Watanabe, Naoki; Kobayashi, Nobumichi

    2013-12-01

    Arginine catabolic mobile element (ACME), a genomic island consisting of the arc and/or opp3 gene clusters found in staphylococcal species, is related to increased bacterial adaptability to hosts. Staphylococcus epidermidis is considered a major ACME reservoir; however, prevalence and genetic diversity of ACME in coagulase-negative staphylococci (CNS) have not yet been well characterized for clinical isolates in Japan. A total of 271 clinical isolates of CNS in a Japanese hospital were investigated for the presence and genotype of ACME and SCCmec. The prevalence of ACME-arcA was significantly higher (p<0.001) in S. epidermidis (45.8%) than in other CNS species (3.7%). ACME in S. epidermidis isolates (n=87) were differentiated into type I (n=33), variant forms of type I (ΔI, n=26) newly identified in this study, type II (n=6), and type ΔII (n=19). ACME-type ΔI, which were further classified into three subtypes, lacked some genetic components between the arc and opp3 clusters in archetypal type I, whereas the arc and opp3 clusters were intact. The arc cluster exhibited high sequence identity (95.8-100%) to that of type I ACME; in contrast, the opp3 cluster was highly diverse, and showed relatively lower identities (94.8-98.7%) to the identical regions in type I ACME. Twenty-one isolates of ΔI ACME-carrying S. epidermidis possessed SCCmec IVa and belonged to ST5 (clonal complex 2). Phylogenetic analysis revealed that isolates harboring ACME ΔI in this study clustered with previously reported S. epidermidis strains with other lineges, suggesting that S. epidermidis originally had some genetic variations in the opp3 cluster. In summary, ACME type ΔI, a truncated variant of ACME-I, was first identified in S. epidermidis, and revealed to be prevalent in ST5 MRSE clinical isolates with SCCmec IVa.

  2. Sealing Force Increasing of ACM Gasket through Electron Beam Radiation

    NASA Astrophysics Data System (ADS)

    dos Santos, D. J.; Batalha, G. F.

    2011-01-01

    Rubber is an engineering material largely used as sealing parts, in form of O-rings, solid gaskets and liquid gaskets, materials applied in liquid state with posterior vulcanization and sealing. Stress relaxation is a rubber characteristic which impacts negatively in such industrial applications (rings and solid gaskets). This work has the purpose to investigate the use of electron beam radiation (EB) as a technology able to decrease the stress relaxation in acrylic rubber (ACM), consequently increasing the sealing capability of this material. ACM samples were irradiated with dose of 100 kGy and 250 kGy, its behavior was comparatively investigated using, dynamic mechanical analysis (DMA) and compression stress relaxation (CSR) experiments. The results obtained by DMA shown an increase of Tg and changes in dynamic mechanical behavior.

  3. 76 FR 64943 - Proposed Cercla Administrative Cost Recovery Settlement; ACM Smelter and Refinery Site, Located...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-19

    ... AGENCY Proposed Cercla Administrative Cost Recovery Settlement; ACM Smelter and Refinery Site, Located in... administrative settlement for recovery of past and projected future response costs concerning the ACM Smelter and...-5027. Comments should reference the ACM Smelter and Refinery NPL Site, the EPA Docket No....

  4. Irrigation impacts on the water cycle and regional climate simulated by the ACME Model

    NASA Astrophysics Data System (ADS)

    Leng, G.; Leung, L. R.; Huang, M.

    2016-12-01

    Irrigation constitutes 70% and 90% of total human freshwater withdraws and consumptions, respectively. In this study, we use the newly developed Accelerated Climate Modeling for Energy (ACME) Earth system model to address the overarching science question as to how irrigation water use interact with terrestrial water resources and feedback to the climate. The location, timing, amount, and sources of irrigation water and irrigate methods are all key processes in modeling irrigation water use and represented in the ACME land model (ALM). Specifically, irrigation starts when soil water content induces soil moisture stress for crops in the prescribed irrigated areas. The soil water deficit is withdrawn from surface water and groundwater. The parameters determining the irrigation amount and surface water/groundwater pumping rate were calibrated to match observations. Irrigation techniques such as sprinkler, flood and drip irrigation as well as irrigation water use efficiency (i.e., the losses during water transport and irrigation application) were also incorporated. The modeling framework was validated against global observations. Generally, including irrigation water use improves the correlation of simulated water components with observations. Several numerical experiments were conducted to examine the irrigation effects on global land surface water and energy flux and its feedback to climate by the coupled land-atmosphere components of ACME. Initial results show that irrigation has greatly interrupted the regional water balance, with alteration of seasonal variability of TWS, increase of evapotranspiration and decrease of streamflow. This alteration is particularly large over heavily irrigated basins such as the Columbia, the Mississippi, the Indus and the Ganges. The shift of water vapor balance and changes in regional climate induced by irrigation will also be briefly discussed.

  5. ACME, a GIS tool for Automated Cirque Metric Extraction

    NASA Astrophysics Data System (ADS)

    Spagnolo, Matteo; Pellitero, Ramon; Barr, Iestyn D.; Ely, Jeremy C.; Pellicer, Xavier M.; Rea, Brice R.

    2017-02-01

    Regional scale studies of glacial cirque metrics provide key insights on the (palaeo) environment related to the formation of these erosional landforms. The growing availability of high resolution terrain models means that more glacial cirques can be identified and mapped in the future. However, the extraction of their metrics still largely relies on time consuming manual techniques or the combination of, more or less obsolete, GIS tools. In this paper, a newly coded toolbox is provided for the automated, and comparatively quick, extraction of 16 key glacial cirque metrics; including length, width, circularity, planar and 3D area, elevation, slope, aspect, plan closure and hypsometry. The set of tools, named ACME (Automated Cirque Metric Extraction), is coded in Python, runs in one of the most commonly used GIS packages (ArcGIS) and has a user friendly interface. A polygon layer of mapped cirques is required for all metrics, while a Digital Terrain Model and a point layer of cirque threshold midpoints are needed to run some of the tools. Results from ACME are comparable to those from other techniques and can be obtained rapidly, allowing large cirque datasets to be analysed and potentially important regional trends highlighted.

  6. Acme jumper pipe system for coke-oven charging

    SciTech Connect

    Medved, P.D.; Thomas, H.

    1996-08-01

    Acme Steel has operated larry cars with an attached jumper pipe since 1977 and had been able to meet the State Implementation Plan (SIP). With the advent of the Clean Air Act (CAA), Acme considered that it could not meet these new standards without modifications to the jumper pipe system. Several drop sleeve modifications, boot seal materials and configurations were tested that resulted in limited success in improving the boot seal life. These modifications showed that the Clean Air Act standards could be met, but it would be cost prohibitive to continue to operate in this manner. The company decided to install an off-car jumper pipe system which uses a traveling U-tube for connection to the assist oven through an additional hole in the roof of each oven. Temperature related failures of drop sleeve seals were eliminated. The off-car jumper pipe is a more efficient gas connection to the assist oven and enables the company to meet the Clean Air Act charging requirements in a cost effective manner.

  7. Fuel gas main replacement at Acme Steel's coke plant

    SciTech Connect

    Trevino, O. . Chicago Coke Plant)

    1994-09-01

    ACME Steel's Chicago coke plant consists of two 4-meter, 50-oven Wilputte underjet coke-oven batteries. These batteries were constructed in 1956--1957. The use of blast furnace gas was discontinued in the late 1960's. In 1977--1978, the oven walls in both batteries were reconstructed. Reconstruction of the underfire system was limited to rebuilding the coke-oven gas reversing cocks and meter in orifices. By the early 1980's, the 24-in. diameter underfire fuel gas mains of both batteries developed leaks at the Dresser expansion joints. These leaks were a result of pipe loss due to corrosion. Leaks also developed along the bottoms and sides of both mains. A method is described that permitted pushing temperatures to be maintained during replacement of underfire fuel gas mains. Each of Acme's two, 50-oven, 4-metric Wilputte coke-oven, gas-fired batteries were heated by converting 10-in. diameter decarbonizing air mains into temporary fuel gas mains. Replacement was made one battery at a time, with the temporary 10-in. mains in service for five to eight weeks.

  8. Predicting Air Combat Maneuvering (ACM) Performance: Fleet Fighter ACM Readiness Program Grades as Performance Criteria.

    DTIC Science & Technology

    1987-10-01

    predict fleet aviator inflight performance using perceptual psychomotor and information processing tasks. The goal is to develop relevant laboratory...were useful in identifying successful and unsuccessful aviators in combat (Viet Nam). Bale at al. (2) evaluated F-4 ’Replacement Air Group (RAG...predict performance. Our approach used performance-based tests of cognitive* perceptual, and multitask functioning to predict fleet operational aviator

  9. Towards an Autonomic Cluster Management System (ACMS) with Reflex Autonomicity

    NASA Technical Reports Server (NTRS)

    Truszkowski, Walt; Hinchey, Mike; Sterritt, Roy

    2005-01-01

    Cluster computing, whereby a large number of simple processors or nodes are combined together to apparently function as a single powerful computer, has emerged as a research area in its own right. The approach offers a relatively inexpensive means of providing a fault-tolerant environment and achieving significant computational capabilities for high-performance computing applications. However, the task of manually managing and configuring a cluster quickly becomes daunting as the cluster grows in size. Autonomic computing, with its vision to provide self-management, can potentially solve many of the problems inherent in cluster management. We describe the development of a prototype Autonomic Cluster Management System (ACMS) that exploits autonomic properties in automating cluster management and its evolution to include reflex reactions via pulse monitoring.

  10. Contribution of the collagen adhesin Acm to pathogenesis of Enterococcus faecium in experimental endocarditis.

    PubMed

    Nallapareddy, Sreedhar R; Singh, Kavindra V; Murray, Barbara E

    2008-09-01

    Enterococcus faecium is a multidrug-resistant opportunist causing difficult-to-treat nosocomial infections, including endocarditis, but there are no reports experimentally demonstrating E. faecium virulence determinants. Our previous studies showed that some clinical E. faecium isolates produce a cell wall-anchored collagen adhesin, Acm, and that an isogenic acm deletion mutant of the endocarditis-derived strain TX0082 lost collagen adherence. In this study, we show with a rat endocarditis model that TX0082 Deltaacm::cat is highly attenuated versus wild-type TX0082, both in established (72 h) vegetations (P < 0.0001) and for valve colonization 1 and 3 hours after infection (P Acm the first factor shown to be important for E. faecium pathogenesis. In contrast, no mortality differences were observed in a mouse peritonitis model. While 5 of 17 endocarditis isolates were Acm nonproducers and failed to adhere to collagen in vitro, all had an intact, highly conserved acm locus. Highly reduced acm mRNA levels (>or=50-fold reduction relative to an Acm producer) were found in three of these five nonadherent isolates, including the sequenced strain TX0016, by quantitative reverse transcription-PCR, indicating that acm transcription is downregulated in vitro in these isolates. However, examination of TX0016 cells obtained directly from infected rat vegetations by flow cytometry showed that Acm was present on 40% of cells grown during infection. Finally, we demonstrated a significant reduction in E. faecium collagen adherence by affinity-purified anti-Acm antibodies from E. faecium endocarditis patient sera, suggesting that Acm may be a potential immunotarget for strategies to control this emerging pathogen.

  11. Using Satellite- and Ground-Based Simulators to Evaluate the US DOE Climate Model (ACME) Simulated Clouds

    NASA Astrophysics Data System (ADS)

    Zhang, Y.; Xie, S.; Lin, W.; Klein, S. A.; Branstetter, M. L.; Evans, K. J.; Marchand, R.; Kollias, P.; Clothiaux, E. E.

    2016-12-01

    It has been challenging to compare cloud measurements with climate model output because of limitations or features of the observing process. The simulator mimics the instrument view of a narrow atmospheric column by accounting for observational limitations of the instruments, so will facilitate direct comparison of modeled clouds with cloud observations. In this study, we implement the CFMIP (the Cloud-Feedback Model Intercomparison Project) Observation Simulator Package (COSP) and the Atmospheric Radiation Measurement (ARM) radar simulator in the US DOE Accelerated Climate Modeling for Energy (ACME) model and evaluate its simulated clouds. The poster shows preliminary results on using the COSP simulator package to evaluate clouds simulated by ACME at 1 degree and 0.25 degree resolutions in its AMIP runs, as well as using the ARM radar simulator to evaluate clouds in ACME day 2 hindcasts at the ARM Southern Great Plains site. Technical issues with developing the ARM radar simulator are discussed. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

  12. Validation of the Adolescent Concerns Measure (ACM): evidence from exploratory and confirmatory factor analysis.

    PubMed

    Ang, Rebecca P; Chong, Wan Har; Huan, Vivien S; Yeo, Lay See

    2007-01-01

    This article reports the development and initial validation of scores obtained from the Adolescent Concerns Measure (ACM), a scale which assesses concerns of Asian adolescent students. In Study 1, findings from exploratory factor analysis using 619 adolescents suggested a 24-item scale with four correlated factors--Family Concerns (9 items), Peer Concerns (5 items), Personal Concerns (6 items), and School Concerns (4 items). Initial estimates of convergent validity for ACM scores were also reported. The four-factor structure of ACM scores derived from Study 1 was confirmed via confirmatory factor analysis in Study 2 using a two-fold cross-validation procedure with a separate sample of 811 adolescents. Support was found for both the multidimensional and hierarchical models of adolescent concerns using the ACM. Internal consistency and test-retest reliability estimates were adequate for research purposes. ACM scores show promise as a reliable and potentially valid measure of Asian adolescents' concerns.

  13. On the characteristics-based ACM for incompressible flows

    NASA Astrophysics Data System (ADS)

    Su, Xiaohui; Zhao, Yong; Huang, Xiaoyang

    2007-11-01

    In this paper, the revised characteristics-based (CB) method for incompressible flows recently derived by Neofytou [P. Neofytou, Revision of the characteristic-based scheme for incompressible flows, J. Comput. Phys. 222 (2007) 475-484] has been further investigated. We have derived all the formulas for pressure and velocities from this revised CB method, which is based on the artificial compressibility method (ACM) [A.J. Chorin, A numerical solution for solving incompressible viscous flow problems, J. Comput. Phys. 2 (1967) 12]. Then we analyze the formulations of the original CB method [D. Drikakis, P.A. Govatsos, D.E. Papatonis, A characteristic based method for incompressible flows, Int. J. Numer. Meth. Fluids 19 (1994) 667-685; E. Shapiro, D. Drikakis, Non-conservative and conservative formulations of characteristics numerical reconstructions for incompressible flows, Int. J. Numer. Meth. Eng. 66 (2006) 1466-1482; D. Drikakis, P.K. Smolarkiewicz, On spurious vortical structures, J. Comput. Phys. 172 (2001) 309-325; F. Mallinger, D. Drikakis, Instability in three-dimensional, unsteady stenotic flows, Int. J. Heat Fluid Flow 23 (2002) 657-663; E. Shapiro, D. Drikakis, Artificial compressibility, characteristics-based schemes for variable density, incompressible, multi-species flows. Parts I. Derivation of different formulations and constant density limit, J. Comput. Phys. 210 (2005) 584-607; Y. Zhao, B. Zhang, A high-order characteristics upwind FV method for incompressible flow and heat transfer simulation on unstructured grids, Comput. Meth. Appl. Mech. Eng. 190 (5-7) (2000) 733-756] to investigate their consistency with the governing flow equations after convergence has been achieved. Furthermore we have implemented both formulations in an unstructured-grid finite volume solver [Y. Zhao, B. Zhang, A high-order characteristics upwind FV method for incompressible flow and heat transfer simulation on unstructured grids, Comput. Meth. Appl. Mech. Eng. 190 (5

  14. ACME: automated cell morphology extractor for comprehensive reconstruction of cell membranes.

    PubMed

    Mosaliganti, Kishore R; Noche, Ramil R; Xiong, Fengzhu; Swinburne, Ian A; Megason, Sean G

    2012-01-01

    The quantification of cell shape, cell migration, and cell rearrangements is important for addressing classical questions in developmental biology such as patterning and tissue morphogenesis. Time-lapse microscopic imaging of transgenic embryos expressing fluorescent reporters is the method of choice for tracking morphogenetic changes and establishing cell lineages and fate maps in vivo. However, the manual steps involved in curating thousands of putative cell segmentations have been a major bottleneck in the application of these technologies especially for cell membranes. Segmentation of cell membranes while more difficult than nuclear segmentation is necessary for quantifying the relations between changes in cell morphology and morphogenesis. We present a novel and fully automated method to first reconstruct membrane signals and then segment out cells from 3D membrane images even in dense tissues. The approach has three stages: 1) detection of local membrane planes, 2) voting to fill structural gaps, and 3) region segmentation. We demonstrate the superior performance of the algorithms quantitatively on time-lapse confocal and two-photon images of zebrafish neuroectoderm and paraxial mesoderm by comparing its results with those derived from human inspection. We also compared with synthetic microscopic images generated by simulating the process of imaging with fluorescent reporters under varying conditions of noise. Both the over-segmentation and under-segmentation percentages of our method are around 5%. The volume overlap of individual cells, compared to expert manual segmentation, is consistently over 84%. By using our software (ACME) to study somite formation, we were able to segment touching cells with high accuracy and reliably quantify changes in morphogenetic parameters such as cell shape and size, and the arrangement of epithelial and mesenchymal cells. Our software has been developed and tested on Windows, Mac, and Linux platforms and is available

  15. acme: The Amendable Coal-Fire Modeling Exercise. A C++ Class Library for the Numerical Simulation of Coal-Fires

    NASA Astrophysics Data System (ADS)

    Wuttke, Manfred W.

    2017-04-01

    At LIAG, we use numerical models to develop and enhance understanding of coupled transport processes and to predict the dynamics of the system under consideration. Topics include geothermal heat utilization, subrosion processes, and spontaneous underground coal fires. Although the details make it inconvenient if not impossible to apply a single code implementation to all systems, their investigations go along similar paths: They all depend on the solution of coupled transport equations. We thus saw a need for a modular code system with open access for the various communities to maximize the shared synergistic effects. To this purpose we develop the oops! ( open object-oriented parallel solutions) - toolkit, a C++ class library for the numerical solution of mathematical models of coupled thermal, hydraulic and chemical processes. This is used to develop problem-specific libraries like acme( amendable coal-fire modeling exercise), a class library for the numerical simulation of coal-fires and applications like kobra (Kohlebrand, german for coal-fire), a numerical simulation code for standard coal-fire models. Basic principle of the oops!-code system is the provision of data types for the description of space and time dependent data fields, description of terms of partial differential equations (pde), their discretisation and solving methods. Coupling of different processes, described by their particular pde is modeled by an automatic timescale-ordered operator-splitting technique. acme is a derived coal-fire specific application library, depending on oops!. If specific functionalities of general interest are implemented and have been tested they will be assimilated into the main oops!-library. Interfaces to external pre- and post-processing tools are easily implemented. Thus a construction kit which can be arbitrarily amended is formed. With the kobra-application constructed with acme we study the processes and propagation of shallow coal seam fires in particular in

  16. Comparative study of numerical schemes of TVD3, UNO3-ACM and optimized compact scheme

    NASA Technical Reports Server (NTRS)

    Lee, Duck-Joo; Hwang, Chang-Jeon; Ko, Duck-Kon; Kim, Jae-Wook

    1995-01-01

    Three different schemes are employed to solve the benchmark problem. The first one is a conventional TVD-MUSCL (Monotone Upwind Schemes for Conservation Laws) scheme. The second scheme is a UNO3-ACM (Uniformly Non-Oscillatory Artificial Compression Method) scheme. The third scheme is an optimized compact finite difference scheme modified by us: the 4th order Runge Kutta time stepping, the 4th order pentadiagonal compact spatial discretization with the maximum resolution characteristics. The problems of category 1 are solved by using the second (UNO3-ACM) and third (Optimized Compact) schemes. The problems of category 2 are solved by using the first (TVD3) and second (UNO3-ACM) schemes. The problem of category 5 is solved by using the first (TVD3) scheme. It can be concluded from the present calculations that the Optimized Compact scheme and the UN03-ACM show good resolutions for category 1 and category 2 respectively.

  17. Comparative study of numerical schemes of TVD3, UNO3-ACM and optimized compact scheme

    NASA Technical Reports Server (NTRS)

    Lee, Duck-Joo; Hwang, Chang-Jeon; Ko, Duck-Kon; Kim, Jae-Wook

    1995-01-01

    Three different schemes are employed to solve the benchmark problem. The first one is a conventional TVD-MUSCL (Monotone Upwind Schemes for Conservation Laws) scheme. The second scheme is a UNO3-ACM (Uniformly Non-Oscillatory Artificial Compression Method) scheme. The third scheme is an optimized compact finite difference scheme modified by us: the 4th order Runge Kutta time stepping, the 4th order pentadiagonal compact spatial discretization with the maximum resolution characteristics. The problems of category 1 are solved by using the second (UNO3-ACM) and third (Optimized Compact) schemes. The problems of category 2 are solved by using the first (TVD3) and second (UNO3-ACM) schemes. The problem of category 5 is solved by using the first (TVD3) scheme. It can be concluded from the present calculations that the Optimized Compact scheme and the UN03-ACM show good resolutions for category 1 and category 2 respectively.

  18. Inhibition of Enterococcus faecium adherence to collagen by antibodies against high-affinity binding subdomains of Acm.

    PubMed

    Nallapareddy, Sreedhar R; Sillanpää, Jouko; Ganesh, Vannakambadi K; Höök, Magnus; Murray, Barbara E

    2007-06-01

    Strains of Enterococcus faecium express a cell wall-anchored protein, Acm, which mediates adherence to collagen. Here, we (i) identify the minimal and high-affinity binding subsegments of Acm and (ii) show that anti-Acm immunoglobulin Gs (IgGs) purified against these subsegments reduced E. faecium TX2535 strain collagen adherence up to 73 and 50%, respectively, significantly more than the total IgGs against the full-length Acm A domain (28%) (P < 0.0001). Blocking Acm adherence with functional subsegment-specific antibodies raises the possibility of their use as therapeutic or prophylactic agents.

  19. The acellular matrix (ACM) for bladder tissue engineering: A quantitative magnetic resonance imaging study.

    PubMed

    Cheng, Hai-Ling Margaret; Loai, Yasir; Beaumont, Marine; Farhat, Walid A

    2010-08-01

    Bladder acellular matrices (ACMs) derived from natural tissue are gaining increasing attention for their role in tissue engineering and regeneration. Unlike conventional scaffolds based on biodegradable polymers or gels, ACMs possess native biomechanical and many acquired biologic properties. Efforts to optimize ACM-based scaffolds are ongoing and would be greatly assisted by a noninvasive means to characterize scaffold properties and monitor interaction with cells. MRI is well suited to this role, but research with MRI for scaffold characterization has been limited. This study presents initial results from quantitative MRI measurements for bladder ACM characterization and investigates the effects of incorporating hyaluronic acid, a natural biomaterial useful in tissue-engineering and regeneration. Measured MR relaxation times (T(1), T(2)) and diffusion coefficient were consistent with increased water uptake and glycosaminoglycan content observed on biochemistry in hyaluronic acid ACMs. Multicomponent MRI provided greater specificity, with diffusion data showing an acellular environment and T(2) components distinguishing the separate effects of increased glycosaminoglycans and hydration. These results suggest that quantitative MRI may provide useful information on matrix composition and structure, which is valuable in guiding further development using bladder ACMs for organ regeneration and in strategies involving the use of hyaluronic acid.

  20. Preliminary survey report: control technology for the ceramic industry at Acme Brick Company, Malvern, Arkansas

    SciTech Connect

    Godbey, F.W.

    1983-06-01

    Health-hazard control methods, work processes, and existing control technologies used in the manufacture of brick were surveyed at Acme Brick Company, Malvern, Arkansas in June, 1983. The company employed about 32 workers to produce structural brick from alluvial clay, free clay, shale, and aggregate. A potential hazard existed from silica exposure since the clays contained about 20% quartz. Raw materials were transported in a cab-enclosed front-end loader to feeders that delivered the materials to a crusher. Blended coarsely crushed material was moved by conveyor to a hammer mill for fine crushing. Production-size product was transported by overhead conveyor to storage silos in the production building. The entire material particle-size reduction process was completely automated. The clay-preparation building and raw-material storage area were isolated from the production building, and only two workers performed the crushing and grinding operations. Material transfer points had removable covers, and a water-mist spray was used on one conveyor of each line. The operation was monitored from a totally enclosed air-conditioned control room. Head and eye protection were required. The author does not recommend an in-depth study of control technologies of the company.

  1. CNTF-ACM promotes mitochondrial respiration and oxidative stress in cortical neurons through upregulating L-type calcium channel activity.

    PubMed

    Sun, Meiqun; Liu, Hongli; Xu, Huanbai; Wang, Hongtao; Wang, Xiaojing

    2016-09-01

    A specialized culture medium termed ciliary neurotrophic factor-treated astrocyte-conditioned medium (CNTF-ACM) allows investigators to assess the peripheral effects of CNTF-induced activated astrocytes upon cultured neurons. CNTF-ACM has been shown to upregulate neuronal L-type calcium channel current activity, which has been previously linked to changes in mitochondrial respiration and oxidative stress. Therefore, the aim of this study was to evaluate CNTF-ACM's effects upon mitochondrial respiration and oxidative stress in rat cortical neurons. Cortical neurons, CNTF-ACM, and untreated control astrocyte-conditioned medium (UC-ACM) were prepared from neonatal Sprague-Dawley rat cortical tissue. Neurons were cultured in either CNTF-ACM or UC-ACM for a 48-h period. Changes in the following parameters before and after treatment with the L-type calcium channel blocker isradipine were assessed: (i) intracellular calcium levels, (ii) mitochondrial membrane potential (ΔΨm), (iii) oxygen consumption rate (OCR) and adenosine triphosphate (ATP) formation, (iv) intracellular nitric oxide (NO) levels, (v) mitochondrial reactive oxygen species (ROS) production, and (vi) susceptibility to the mitochondrial complex I toxin rotenone. CNTF-ACM neurons displayed the following significant changes relative to UC-ACM neurons: (i) increased intracellular calcium levels (p < 0.05), (ii) elevation in ΔΨm (p < 0.05), (iii) increased OCR and ATP formation (p < 0.05), (iv) increased intracellular NO levels (p < 0.05), (v) increased mitochondrial ROS production (p < 0.05), and (vi) increased susceptibility to rotenone (p < 0.05). Treatment with isradipine was able to partially rescue these negative effects of CNTF-ACM (p < 0.05). CNTF-ACM promotes mitochondrial respiration and oxidative stress in cortical neurons through elevating L-type calcium channel activity.

  2. ACM CCS 2013-2015 Student Travel Support

    DTIC Science & Technology

    2016-10-29

    comprising 82 experts from 16 countries as well as 310 external reviewers evaluated these submissions in the customary double- blind manner. At the end of...submissions employing the customary double- blind review procedure. The review process resulted in 114 papers being accepted to the program, representing...customary double- blind review procedure. The review process resulted in 128 papers being accepted to the program (with authors from 19 countries

  3. Validation of the Adolescent Concerns Measure (ACM): Evidence from Exploratory and Confirmatory Factor Analysis

    ERIC Educational Resources Information Center

    Ang, Rebecca P.; Chong, Wan Har; Huan, Vivien S.; Yeo, Lay See

    2007-01-01

    This article reports the development and initial validation of scores obtained from the Adolescent Concerns Measure (ACM), a scale which assesses concerns of Asian adolescent students. In Study 1, findings from exploratory factor analysis using 619 adolescents suggested a 24-item scale with four correlated factors--Family Concerns (9 items), Peer…

  4. SUPERFUND TREATABILITY CLEARINGHOUSE: FINAL REPORT, PHASE I - IMMEDIATE ASSESSMENT, ACME SOLVENTS SITE

    EPA Science Inventory

    This is a site assessment and feasibility study of incineration alternatives at the ACME Solvents Site at Rockford, Illinois. The document contains laboratory results that are reported to simulate incineration conditions but no details on test methods were provided. The d...

  5. SUPERFUND TREATABILITY CLEARINGHOUSE: FINAL REPORT, PHASE I - IMMEDIATE ASSESSMENT, ACME SOLVENTS SITE

    EPA Science Inventory

    This is a site assessment and feasibility study of incineration alternatives at the ACME Solvents Site at Rockford, Illinois. The document contains laboratory results that are reported to simulate incineration conditions but no details on test methods were provided. The d...

  6. On-resin conversion of Cys(Acm)-containing peptides to their corresponding Cys(Scm) congeners.

    PubMed

    Mullen, Daniel G; Weigel, Benjamin; Barany, George; Distefano, Mark D

    2010-05-01

    The Acm protecting group for the thiol functionality of cysteine is removed under conditions (Hg(2+)) that are orthogonal to the acidic milieu used for global deprotection in Fmoc-based solid-phase peptide synthesis. This use of a toxic heavy metal for deprotection has limited the usefulness of Acm in peptide synthesis. The Acm group may be converted to the Scm derivative that can then be used as a reactive intermediate for unsymmetrical disulfide formation. It may also be removed by mild reductive conditions to generate unprotected cysteine. Conversion of Cys(Acm)-containing peptides to their corresponding Cys(Scm) derivatives in solution is often problematic because the sulfenyl chloride reagent used for this conversion may react with the sensitive amino acids tyrosine and tryptophan. In this protocol, we report a method for on-resin Acm to Scm conversion that allows the preparation of Cys(Scm)-containing peptides under conditions that do not modify other amino acids.

  7. ARM Airborne Carbon Measurements (ARM-ACME) and ARM-ACME 2.5 Final Campaign Reports

    SciTech Connect

    Biraud, S. C.; Tom, M. S.; Sweeney, C.

    2016-01-01

    We report on a 5-year multi-institution and multi-agency airborne study of atmospheric composition and carbon cycling at the Atmospheric Radiation Measurement (ARM) Climate Research Facility’s Southern Great Plains (SGP) site, with scientific objectives that are central to the carbon-cycle and radiative-forcing goals of the U.S. Global Change Research Program and the North American Carbon Program (NACP). The goal of these measurements is to improve understanding of 1) the carbon exchange of the Atmospheric Radiation Measurement (ARM) SGP region; 2) how CO2 and associated water and energy fluxes influence radiative-forcing, convective processes, and CO2 concentrations over the ARM SGP region, and 3) how greenhouse gases are transported on continental scales.

  8. Categorization of Computing Education Resources into the ACM Computing Classification System

    SciTech Connect

    Chen, Yinlin; Bogen, Paul Logasa; Fox, Dr. Edward A.; Hsieh, Dr. Haowei; Cassel, Dr. Lillian N.

    2012-01-01

    The Ensemble Portal harvests resources from multiple heterogonous federated collections. Managing these dynamically increasing collections requires an automatic mechanism to categorize records in to corresponding topics. We propose an approach to use existing ACM DL metadata to build classifiers for harvested resources in the Ensemble project. We also present our experience on utilizing the Amazon Mechanical Turk platform to build ground truth training data sets from Ensemble collections.

  9. Clouds and Precipitation Simulated by the US DOE Accelerated Climate Modeling for Energy (ACME)

    NASA Astrophysics Data System (ADS)

    Xie, S.; Lin, W.; Yoon, J. H.; Ma, P. L.; Rasch, P. J.; Ghan, S.; Zhang, K.; Zhang, Y.; Zhang, C.; Bogenschutz, P.; Gettelman, A.; Larson, V. E.; Neale, R. B.; Park, S.; Zhang, G. J.

    2015-12-01

    A new US Department of Energy (DOE) climate modeling effort is to develop an Accelerated Climate Model for Energy (ACME) to accelerate the development and application of fully coupled, state-of-the-art Earth system models for scientific and energy application. ACME is a high-resolution climate model with a 0.25 degree in horizontal and more than 60 levels in the vertical. It starts from the Community Earth System Model (CESM) with notable changes to its physical parameterizations and other components. This presentation provides an overview on the ACME model's capability in simulating clouds and precipitation and its sensitivity to convection schemes. Results with using several state-of-the-art cumulus convection schemes, including those unified parameterizations that are being developed in the climate community, will be presented. These convection schemes are evaluated in a multi-scale framework including both short-range hindcasts and free-running climate simulations with both satellite data and ground-based measurements. Running climate model in short-range hindcasts has been proven to be an efficient way to understand model deficiencies. The analysis is focused on those systematic errors in clouds and precipitation simulations that are shared in many climate models. The goal is to understand what model deficiencies might be primarily responsible for these systematic errors.

  10. Effects of activated ACM on expression of signal transducers in cerebral cortical neurons of rats.

    PubMed

    Wang, Xiaojing; Li, Zhengli; Zhu, Changgeng; Li, Zhongyu

    2007-06-01

    To explore the roles of astrocytes in the epileptogenesis, astrocytes and neurons were isolated, purified and cultured in vitro from cerebral cortex of rats. The astrocytes were activated by ciliary neurotrophic factor (CNTF) and astrocytic conditioned medium (ACM) was collected to treat neurons for 4, 8 and 12 h. By using Western blot, the expression of calmodulin dependent protein kinase II (CaMK II), inducible nitric oxide synthase (iNOS) and adenylate cyclase (AC) was detected in neurons. The results showed that the expression of CaMK II, iNOS and AC was increased significantly in the neurons treated with ACM from 4 h to 12 h (P<0.05), and that of iNOS and AC peaked at 8 h and 12 h respectively. It was suggested that there might be some epileptogenic factors in the ACM and such signal pathways as NOS-NO-cGMP, Ca2+/CaM-CaMK II and AC-cAMP-PKA might take part in the signal transduction of epileptogenesis.

  11. Model Diagnostics for the Department of Energy's Accelerated Climate Modeling for Energy (ACME) Project

    NASA Astrophysics Data System (ADS)

    Smith, B.

    2015-12-01

    In 2014, eight Department of Energy (DOE) national laboratories, four academic institutions, one company, and the National Centre for Atmospheric Research combined forces in a project called Accelerated Climate Modeling for Energy (ACME) with the goal to speed Earth system model development for climate and energy. Over the planned 10-year span, the project will conduct simulations and modeling on DOE's most powerful high-performance computing systems at Oak Ridge, Argonne, and Lawrence Berkeley Leadership Compute Facilities. A key component of the ACME project is the development of an interactive test bed for the advanced Earth system model. Its execution infrastructure will accelerate model development and testing cycles. The ACME Workflow Group is leading the efforts to automate labor-intensive tasks, provide intelligent support for complex tasks and reduce duplication of effort through collaboration support. As part of this new workflow environment, we have created a diagnostic, metric, and intercomparison Python framework, called UVCMetrics, to aid in the testing-to-production execution of the ACME model. The framework exploits similarities among different diagnostics to compactly support diagnosis of new models. It presently focuses on atmosphere and land but is designed to support ocean and sea ice model components as well. This framework is built on top of the existing open-source software framework known as the Ultrascale Visualization Climate Data Analysis Tools (UV-CDAT). Because of its flexible framework design, scientists and modelers now can generate thousands of possible diagnostic outputs. These diagnostics can compare model runs, compare model vs. observation, or simply verify a model is physically realistic. Additional diagnostics are easily integrated into the framework, and our users have already added several. Diagnostics can be generated, viewed, and manipulated from the UV-CDAT graphical user interface, Python command line scripts and programs

  12. On the modeling of a single-stage, entrained-flow gasifier using Aspen Custom Modeler (ACM)

    SciTech Connect

    Kasule, J.; Turton, R.; Bhattacharyya, D.; Zitney, S.

    2010-01-01

    Coal-fired gasifiers are the centerpiece of integrated gasification combined cycle (IGCC) power plants. The gasifier produces synthesis gas that is subsequently converted into electricity through combustion in a gas turbine. Several mathematical models have been developed to study the physical and chemical processes taking place inside the gasifier. Such models range from simple one-dimensional (1D) steady-state models to sophisticated dynamic 3D computational fluid dynamics (CFD) models that incorporate turbulence effects in the reactor. The practical operation of the gasifier is dynamic in nature but most 1D and some higher-dimensional models are often steady state. On the other hand, many higher order CFD-based models are dynamic in nature, but are too computationally expensive to be used directly in operability and controllability dynamic studies. They are also difficult to incorporate in the framework of process simulation software such as Aspen Plus Dynamics. Thus lower-dimensional dynamic models are still useful in these types of studies. In the current study, a 1D dynamic model for a single-stage, downward-firing, entrained-flow GE-type gasifier is developed using Aspen Custom Modeler{reg_sign} (ACM), which is a commercial equation-based simulator for creating, editing, and re-using models of process units. The gasifier model is based on mass, momentum, and energy balances for the solid and gas phases. The physical and chemical reactions considered in the model are drying, devolatilization/pyrolysis, gasification, combustion, and the homogeneous gas phase reactions. The dynamic gasifier model is being developed for use in a plant-wide dynamic model of an IGCC power plant. For dynamic simulation, the resulting highly nonlinear system of partial differential algebraic equations (PDAE) is solved in ACM using the well-known Method of Lines (MoL) approach. The MoL discretizes the space domain and leaves the time domain continuous, thereby converting the PDAE to

  13. Experimental determination of the partitioning coefficient and volatility of important BVOC oxidation products using the Aerosol Collection Module (ACM) coupled to a PTR-ToF-MS

    NASA Astrophysics Data System (ADS)

    Gkatzelis, G.; Hohaus, T.; Tillmann, R.; Schmitt, S. H.; Yu, Z.; Schlag, P.; Wegener, R.; Kaminski, M.; Kiendler-Scharr, A.

    2015-12-01

    Atmospheric aerosol can alter the Earth's radiative budget and global climate but can also affect human health. A dominant contributor to the submicrometer particulate matter (PM) is organic aerosol (OA). OA can be either directly emitted through e.g. combustion processes (primary OA) or formed through the oxidation of organic gases (secondary organic aerosol, SOA). A detailed understanding of SOA formation is of importance as it constitutes a major contribution to the total OA. The partitioning between the gas and particle phase as well as the volatility of individual components of SOA is yet poorly understood adding uncertainties and thus complicating climate modelling. In this work, a new experimental methodology was used for compound-specific analysis of organic aerosol. The Aerosol Collection Module (ACM) is a newly developed instrument that deploys an aerodynamic lens to separate the gas and particle phase of an aerosol. The particle phase is directed to a cooled sampling surface. After collection particles are thermally desorbed and transferred to a detector for further analysis. In the present work, the ACM was coupled to a Proton Transfer Reaction-Time of Flight-Mass Spectrometer (PTR-ToF-MS) to detect and quantify organic compounds partitioning between the gas and particle phase. This experimental approach was used in a set of experiments at the atmosphere simulation chamber SAPHIR to investigate SOA formation. Ozone oxidation with subsequent photochemical aging of β-pinene, limonene and real plant emissions from Pinus sylvestris (Scots pine) were studied. Simultaneous measurement of the gas and particle phase using the ACM-PTR-ToF-MS allows to report partitioning coefficients of important BVOC oxidation products. Additionally, volatility trends and changes of the SOA with photochemical aging are investigated and compared for all systems studied.

  14. Improving Throughput of the ACME Climate Model by Parallel Splitting Atmospheric Physics and Dynamics

    NASA Astrophysics Data System (ADS)

    Caldwell, P.; Taylor, M.

    2015-12-01

    If fluid dynamics and atmospheric physics parameterizations were computed in parallel, they could be calculated simultaneously on separate cores of a supercomputer. This would greatly increase model throughput for high-resolution simulations. Additionally, because atmospheric physics is embarrassingly parallel, more sophisticated physics parameterizations could be used without slowing simulations down by simply increasing the number of cores used. The downside to this approach is that it increases time-truncation error. In this presentation, we demonstrate that parallel splitting the ACME model and using a smaller timestep for physics results in faster, more accurate solutions.

  15. Information Criterion Comparison of Two Deep Convection Ensembles in the ACME Climate Model

    NASA Astrophysics Data System (ADS)

    Lucas, D. D.; Anderson, G. J.; Bulaevskaya, V.; Chowdhary, K.; Debusschere, B.; Ghan, S. J.

    2016-12-01

    Statistical model selection methods have been developed and applied to compare the performance of two deep convection parameterizations in the U.S. Dept. of Energy's ACME climate model. The comparison is based on information criterion scores that summarize the goodness-of-fit to observations of tropical precipitation and penalize against overfitting. The scores are derived using an ensemble of 400 Latin hypercube simulations of the global ACME model (1 degree, 30 levels) that perturb parameters in the Zhang-Mcfarlane and Chikira deep convection schemes. The ensemble is used to train statistical models, identify influential model parameters, determine maximum likelihood estimates, and compute information criterion scores. The scores can be used to provide guidance on the selection of a deep convection parameterization for a climate model. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344, and is supported by the DOE Office of Science through the Scientific Discovery Through Advanced Computing (SciDAC).

  16. Superfund Record of Decision (EPA Region 5): Acme Solvents, Morristown, Illinois, September 1985. Final report

    SciTech Connect

    Not Available

    1985-09-27

    The Acme Solvents Reclaiming, Inc. facility is located approximately five miles south of Rockford, Illinois. From 1960 until 1973, the facility served as a disposal site for paints, oils and still bottoms from the solvent reclamation plant located in Rockford. In addition, empty drums were stored onsite. Wastes were dumped into depressions created from either previous quarrying activities or by scraping overburden from the near surface bedrock to form berms. In September 1972, the Illinois Pollution Control Board (IPCB) ordered Acme to remove all drums and wastes from the facility and to backfill the lagoons. Follow-up inspections revealed that wastes and crushed drums were being left onsite and merely covered with soil. Sampling of the site revealed high concentrations of chlorinated organics in the drinking water. The major source of hazardous substances at the facility are the waste disposal mounds. These mounds contain volatile and semi-volatile organic compounds and concentrations of PCBs up to several hundred mg/kg. The selected remedial action is included.

  17. TWO NOVEL ACM (ACTIVE CONTOUR MODEL) METHODS FOR INTRAVASCULAR ULTRASOUND IMAGE SEGMENTATION

    SciTech Connect

    Chen, Chi Hau; Potdat, Labhesh; Chittineni, Rakesh

    2010-02-22

    One of the attractive image segmentation methods is the Active Contour Model (ACM) which has been widely used in medical imaging as it always produces sub-regions with continuous boundaries. Intravascular ultrasound (IVUS) is a catheter based medical imaging technique which is used for quantitative assessment of atherosclerotic disease. Two methods of ACM realizations are presented in this paper. The gradient descent flow based on minimizing energy functional can be used for segmentation of IVUS images. However this local operation alone may not be adequate to work with the complex IVUS images. The first method presented consists of basically combining the local geodesic active contours and global region-based active contours. The advantage of combining the local and global operations is to allow curves deforming under the energy to find only significant local minima and delineate object borders despite noise, poor edge information and heterogeneous intensity profiles. Results for this algorithm are compared to standard techniques to demonstrate the method's robustness and accuracy. In the second method, the energy function is appropriately modified and minimized using a Hopfield neural network. Proper modifications in the definition of the bias of the neurons have been introduced to incorporate image characteristics. The method overcomes distortions in the expected image pattern, such as due to the presence of calcium, and employs a specialized structure of the neural network and boundary correction schemes which are based on a priori knowledge about the vessel geometry. The presented method is very fast and has been evaluated using sequences of IVUS frames.

  18. Two Novel ACM (active Contour Model) Methods for Intravascular Ultrasound Image Segmentation

    NASA Astrophysics Data System (ADS)

    Chen, Chi Hau; Potdat, Labhesh; Chittineni, Rakesh

    2010-02-01

    One of the attractive image segmentation methods is the Active Contour Model (ACM) which has been widely used in medical imaging as it always produces sub-regions with continuous boundaries. Intravascular ultrasound (IVUS) is a catheter based medical imaging technique which is used for quantitative assessment of atherosclerotic disease. Two methods of ACM realizations are presented in this paper. The gradient descent flow based on minimizing energy functional can be used for segmentation of IVUS images. However this local operation alone may not be adequate to work with the complex IVUS images. The first method presented consists of basically combining the local geodesic active contours and global region-based active contours. The advantage of combining the local and global operations is to allow curves deforming under the energy to find only significant local minima and delineate object borders despite noise, poor edge information and heterogeneous intensity profiles. Results for this algorithm are compared to standard techniques to demonstrate the method's robustness and accuracy. In the second method, the energy function is appropriately modified and minimized using a Hopfield neural network. Proper modifications in the definition of the bias of the neurons have been introduced to incorporate image characteristics. The method overcomes distortions in the expected image pattern, such as due to the presence of calcium, and employs a specialized structure of the neural network and boundary correction schemes which are based on a priori knowledge about the vessel geometry. The presented method is very fast and has been evaluated using sequences of IVUS frames.

  19. Clinical isolates of Enterococcus faecium exhibit strain-specific collagen binding mediated by Acm, a new member of the MSCRAMM family.

    PubMed

    Nallapareddy, Sreedhar R; Weinstock, George M; Murray, Barbara E

    2003-03-01

    A collagen-binding adhesin of Enterococcus faecium, Acm, was identified. Acm shows 62% similarity to the Staphylococcus aureus collagen adhesin Cna over the entire protein and is more similar to Cna (60% and 75% similarity with Cna A and B domains respectively) than to the Enterococcus faecalis collagen-binding adhesin, Ace, which shares homology with Acm only in the A domain. Despite the detection of acm in 32 out of 32 E. faecium isolates, only 11 of these (all clinical isolates, including four vancomycin-resistant endocarditis isolates and seven other isolates) exhibited binding to collagen type I (CI). Although acm from three CI-binding vancomycin-resistant E. faecium clinical isolates showed 100% identity, analysis of acm genes and their promoter regions from six non-CI-binding strains identified deletions or mutations that introduced stop codons and/or IS elements within the gene or the promoter region in five out of six strains, suggesting that the presence of an intact functional acm gene is necessary for binding of E. faecium strains to CI. Recombinant Acm A domain showed specific and concentration-dependent binding to collagen, and this protein competed with E. faecium binding to immobilized CI. Consistent with the adherence phenotype and sequence data, probing with Acm-specific IgGs purified from anti-recombinant Acm A polyclonal rabbit serum confirmed the surface expression of Acm in three out of three collagen-binding clinical isolates of E. faecium tested, but in none of the strains with a non-functional pseudo acm gene. Introduction of a functional acm gene into two non-CI-binding natural acm mutant strains conferred a CI-binding phenotype, further confirming that native Acm is sufficient for the binding of E. faecium to CI. These results demonstrate that acm, which encodes a potential virulence factor, is functional only in certain infection-derived clinical isolates of E. faecium, and suggest that Acm is the primary adhesin responsible for the

  20. Evidence for heterogeneity of astrocyte de-differentiation in vitro: astrocytes transform into intermediate precursor cells following induction of ACM from scratch-insulted astrocytes.

    PubMed

    Yang, Hao; Qian, Xin-Hong; Cong, Rui; Li, Jing-wen; Yao, Qin; Jiao, Xi-Ying; Ju, Gong; You, Si-Wei

    2010-04-01

    Our previous study definitely demonstrated that the mature astrocytes could undergo a de-differentiation process and further transform into pluripotential neural stem cells (NSCs), which might well arise from the effect of diffusible factors released from scratch-insulted astrocytes. However, these neurospheres passaged from one neurosphere-derived from de-differentiated astrocytes possessed a completely distinct characteristic in the differentiation behavior, namely heterogeneity of differentiation. The heterogeneity in cell differentiation has become a crucial but elusive issue. In this study, we show that purified astrocytes could de-differentiate into intermediate precursor cells (IPCs) with addition of scratch-insulted astrocyte-conditioned medium (ACM) to the culture, which can express NG2 and A2B5, the IPCs markers. Apart from the number of NG2(+) and A2B5(+) cells, the percentage of proliferative cells as labeled with BrdU progressively increased with prolonged culture period ranging from 1 to 10 days. Meanwhile, the protein level of A2B5 in cells also increased significantly. These results revealed that not all astrocytes could de-differentiate fully into NSCs directly when induced by ACM, rather they generated intermediate or more restricted precursor cells that might undergo progressive de-differentiation to generate NSCs.

  1. AcmB Is an S-Layer-Associated β-N-Acetylglucosaminidase and Functional Autolysin in Lactobacillus acidophilus NCFM

    PubMed Central

    Johnson, Brant R.

    2016-01-01

    ABSTRACT Autolysins, also known as peptidoglycan hydrolases, are enzymes that hydrolyze specific bonds within bacterial cell wall peptidoglycan during cell division and daughter cell separation. Within the genome of Lactobacillus acidophilus NCFM, there are 11 genes encoding proteins with peptidoglycan hydrolase catalytic domains, 9 of which are predicted to be functional. Notably, 5 of the 9 putative autolysins in L. acidophilus NCFM are S-layer-associated proteins (SLAPs) noncovalently colocalized along with the surface (S)-layer at the cell surface. One of these SLAPs, AcmB, a β-N-acetylglucosaminidase encoded by the gene lba0176 (acmB), was selected for functional analysis. In silico analysis revealed that acmB orthologs are found exclusively in S-layer- forming species of Lactobacillus. Chromosomal deletion of acmB resulted in aberrant cell division, autolysis, and autoaggregation. Complementation of acmB in the ΔacmB mutant restored the wild-type phenotype, confirming the role of this SLAP in cell division. The absence of AcmB within the exoproteome had a pleiotropic effect on the extracellular proteins covalently and noncovalently bound to the peptidoglycan, which likely led to the observed decrease in the binding capacity of the ΔacmB strain for mucin and extracellular matrices fibronectin, laminin, and collagen in vitro. These data suggest a functional association between the S-layer and the multiple autolysins noncovalently colocalized at the cell surface of L. acidophilus NCFM and other S-layer-producing Lactobacillus species. IMPORTANCE Lactobacillus acidophilus is one of the most widely used probiotic microbes incorporated in many dairy foods and dietary supplements. This organism produces a surface (S)-layer, which is a self-assembling crystalline array found as the outermost layer of the cell wall. The S-layer, along with colocalized associated proteins, is an important mediator of probiotic activity through intestinal adhesion and modulation of

  2. Can Pearlite form Outside of the Hultgren Extrapolation of the Ae3 and Acm Phase Boundaries?

    NASA Astrophysics Data System (ADS)

    Aranda, M. M.; Rementeria, R.; Capdevila, C.; Hackenberg, R. E.

    2016-02-01

    It is usually assumed that ferrous pearlite can form only when the average austenite carbon concentration C 0 lies between the extrapolated Ae3 ( γ/ α) and Acm ( γ/ θ) phase boundaries (the "Hultgren extrapolation"). This "mutual supersaturation" criterion for cooperative lamellar nucleation and growth is critically examined from a historical perspective and in light of recent experiments on coarse-grained hypoeutectoid steels which show pearlite formation outside the Hultgren extrapolation. This criterion, at least as interpreted in terms of the average austenite composition, is shown to be unnecessarily restrictive. The carbon fluxes evaluated from Brandt's solution are sufficient to allow pearlite growth both inside and outside the Hultgren Extrapolation. As for the feasibility of the nucleation events leading to pearlite, the only criterion is that there are some local regions of austenite inside the Hultgren Extrapolation, even if the average austenite composition is outside.

  3. Autonomic Cluster Management System (ACMS): A Demonstration of Autonomic Principles at Work

    NASA Technical Reports Server (NTRS)

    Baldassari, James D.; Kopec, Christopher L.; Leshay, Eric S.; Truszkowski, Walt; Finkel, David

    2005-01-01

    Cluster computing, whereby a large number of simple processors or nodes are combined together to apparently function as a single powerful computer, has emerged as a research area in its own right. The approach offers a relatively inexpensive means of achieving significant computational capabilities for high-performance computing applications, while simultaneously affording the ability to. increase that capability simply by adding more (inexpensive) processors. However, the task of manually managing and con.guring a cluster quickly becomes impossible as the cluster grows in size. Autonomic computing is a relatively new approach to managing complex systems that can potentially solve many of the problems inherent in cluster management. We describe the development of a prototype Automatic Cluster Management System (ACMS) that exploits autonomic properties in automating cluster management.

  4. Sparse Polynomial Chaos Surrogate for ACME Land Model via Iterative Bayesian Compressive Sensing

    NASA Astrophysics Data System (ADS)

    Sargsyan, K.; Ricciuto, D. M.; Safta, C.; Debusschere, B.; Najm, H. N.; Thornton, P. E.

    2015-12-01

    For computationally expensive climate models, Monte-Carlo approaches of exploring the input parameter space are often prohibitive due to slow convergence with respect to ensemble size. To alleviate this, we build inexpensive surrogates using uncertainty quantification (UQ) methods employing Polynomial Chaos (PC) expansions that approximate the input-output relationships using as few model evaluations as possible. However, when many uncertain input parameters are present, such UQ studies suffer from the curse of dimensionality. In particular, for 50-100 input parameters non-adaptive PC representations have infeasible numbers of basis terms. To this end, we develop and employ Weighted Iterative Bayesian Compressive Sensing to learn the most important input parameter relationships for efficient, sparse PC surrogate construction with posterior uncertainty quantified due to insufficient data. Besides drastic dimensionality reduction, the uncertain surrogate can efficiently replace the model in computationally intensive studies such as forward uncertainty propagation and variance-based sensitivity analysis, as well as design optimization and parameter estimation using observational data. We applied the surrogate construction and variance-based uncertainty decomposition to Accelerated Climate Model for Energy (ACME) Land Model for several output QoIs at nearly 100 FLUXNET sites covering multiple plant functional types and climates, varying 65 input parameters over broad ranges of possible values. This work is supported by the U.S. Department of Energy, Office of Science, Biological and Environmental Research, Accelerated Climate Modeling for Energy (ACME) project. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  5. AcmA of Lactococcus lactis is an N-acetylglucosaminidase with an optimal number of LysM domains for proper functioning.

    PubMed

    Steen, Anton; Buist, Girbe; Horsburgh, Gavin J; Venema, Gerard; Kuipers, Oscar P; Foster, Simon J; Kok, Jan

    2005-06-01

    AcmA, the major autolysin of Lactococcus lactis MG1363 is a modular protein consisting of an N-terminal active site domain and a C-terminal peptidoglycan-binding domain. The active site domain is homologous to that of muramidase-2 of Enterococcus hirae, however, RP-HPLC analysis of muropeptides released from Bacillus subtilis peptidoglycan, after digestion with AcmA, shows that AcmA is an N-acetylglucosaminidase. In the C-terminus of AcmA three highly similar repeated regions of 45 amino acid residues are present, which are separated by short nonhomologous sequences. The repeats of AcmA, which belong to the lysine motif (LysM) domain family, were consecutively deleted, removed, or, alternatively, one additional repeat was added, without destroying the cell wall-hydrolyzing activity of the enzyme in vitro, although AcmA activity was reduced in all cases. In vivo, proteins containing no or only one repeat did not give rise to autolysis of lactococcal cells, whereas separation of the producer cells from the chains was incomplete. Exogenously added AcmA deletion derivatives carrying two repeats or four repeats bound to lactococcal cells, whereas the derivative with no or one repeat did not. In conclusion, these results show that AcmA needs three LysM domains for optimal peptidoglycan binding and biological functioning.

  6. Asteroids, comets, Kuiper Belt objects, meteors: the ACM (AKM) 2002 perspective

    NASA Astrophysics Data System (ADS)

    Binzel, Richard P.

    2002-11-01

    An impressionistic overview is given on the state of science of Asteroider, Kometer, Meteorer (AKM), where the Swedish spelling is adopted in recognition of the origin of the ACM conference series. Asteroider (asteroids) are a field that has come of age to the point of asking sophisticated geological and geophysical questions based on dedicated spacecraft missions. Kometer (comets) are coming of age with a strong international emphasis toward new comet missions and ever increasing sophistication of Earth-based observations. K also stands for Kuiper belt objects, a field that wasn't invented when our conference series began but whose inclusion we embrace and recognize as being integral to our science. (Hence the recommendation that we adopt the moniker AKM to proclaim fully our inclusivity) KBOs are an emerging field, perhaps analogous to a fast growing child. The presently known number of KBOs is comparable to the number of known main-belt asteroids in 1900, suggesting that we are just beginning to learn about this region. Meteorer (meteors) is a rejuvenated field that has enjoyed spectacular recent successes in detailed predictions of the Leonid shower and in just recently recording the fall and recovering the Neuschwanstein meteorite. The future outlook portends the greatest advancement in K (kometer and KBOs) with broad interdisciplinary implications.

  7. Selective desulfurization of cysteine in the presence of Cys(Acm) in polypeptides obtained by native chemical ligation.

    PubMed

    Pentelute, Brad L; Kent, Stephen B H

    2007-02-15

    Increased versatility for the synthesis of proteins and peptides by native chemical ligation requires the ability to ligate at positions other than Cys. Here, we report that Raney nickel can be used under standard conditions for the selective desulfurization of Cys in the presence of Cys(Acm). This simple and practical tactic enables the more common Xaa-Ala junctions to be used as ligation sites for the chemical synthesis of Cys-containing peptides and proteins. [reaction: see text].

  8. Geologic, geotechnical, and geophysical properties of core from the Acme Fire-Pit-1 drill hole, Sheridan County, Wyoming

    USGS Publications Warehouse

    Collins, Donley S.

    1983-01-01

    A preliminary core study from the Acme Fire-Pit-1 drill hole, Sheridan County, Wyoming, revealed that the upper portion of the core had been baked by a fire confined to the underlying Monarch coal bed. The baked (clinkered) sediment above the Monarch coal bed was determined to have higher point-load strength values (greater than 2 MPa) than the sediment under the burned coal

  9. ACME-V mission in the North Slope of Alaska (Airborne Carbon MEasurements)

    NASA Astrophysics Data System (ADS)

    Biraud, S.; Torn, M. S.; Sedlacek, A. J., III; Sweeney, C.; Springston, S. R.

    2016-12-01

    Atmospheric temperatures are warming faster in the Arctic than predicted by climate models. The impact of this warming on permafrost degradation is not well understood, but it is projected to increase carbon decomposition and greenhouse gas production (CO2 and/or CH4) by arctic ecosystems. Airborne observations of atmospheric trace gases, aerosols and cloud properties in North Slopes of Alaska (NSA) are improving our understanding of global climate, with the goal of reducing the uncertainty in global and regional climate simulations and projections. From June 1 through September 15, 2015, the Atmospheric radiation measurement (ARM) airborne facility (AAF) deployed a G1 research aircraft (ARM-ACME-V mission) to fly over the North Slope of Alaska, with occasional vertical profiling to measure trace gas concentrations, between Prudhoe Bay, Oliktok point, Barrow, Atqasuk, Ivotuk, and Toolik Lake. The aircraft payload includes a Picarro and a LGR analyzers for continuous measurements of CO2, CH4, H2O, and CO and N2O mixing ratios, and a 12-flask sampler for analysis of carbon cycle gases (CO2, CO, CH4, N2O, 13CO2, 14CO2, carbonyl sulfide, and trace hydrocarbon species including ethane). The aircraft payload also include measurements of aerosol properties (number size distribution, total number concentration, absorption, and scattering), cloud properties (droplet and ice size information), atmospheric thermodynamic state, and solar/infrared radiation. Preliminary results using CO2, CH4, CO, ethane, and soot spectroscopy observations are used to tease apart biogenic and thermogenic (biomass burning, and oil and gas production) contributions.

  10. Segmentation of solid subregion of high grade gliomas in MRI images based on active contour model (ACM)

    NASA Astrophysics Data System (ADS)

    Seow, P.; Win, M. T.; Wong, J. H. D.; Abdullah, N. A.; Ramli, N.

    2016-03-01

    Gliomas are tumours arising from the interstitial tissue of the brain which are heterogeneous, infiltrative and possess ill-defined borders. Tumour subregions (e.g. solid enhancing part, edema and necrosis) are often used for tumour characterisation. Tumour demarcation into substructures facilitates glioma staging and provides essential information. Manual segmentation had several drawbacks that include laborious, time consuming, subjected to intra and inter-rater variability and hindered by diversity in the appearance of tumour tissues. In this work, active contour model (ACM) was used to segment the solid enhancing subregion of the tumour. 2D brain image acquisition data using 3T MRI fast spoiled gradient echo sequence in post gadolinium of four histologically proven high-grade glioma patients were obtained. Preprocessing of the images which includes subtraction and skull stripping were performed and then followed by ACM segmentation. The results of the automatic segmentation method were compared against the manual delineation of the tumour by a trainee radiologist. Both results were further validated by an experienced neuroradiologist and a brief quantitative evaluations (pixel area and difference ratio) were performed. Preliminary results of the clinical data showed the potential of ACM model in the application of fast and large scale tumour segmentation in medical imaging.

  11. Utility of adaptive control processing for the interpretation of digital mammograms.

    PubMed

    Jinnouchi, Mikako; Yabuuchi, Hidetake; Kubo, Makoto; Tokunaga, Eriko; Yamamoto, Hidetaka; Honda, Hiroshi

    2016-11-01

    Background Adaptive control processing for mammography (ACM) is a novel program that automatically sets up appropriate image-processing parameters for individual mammograms (MMGs) by analyzing the focal and whole breast histogram. Purpose To investigate whether ACM improves the image contrast of digital MMGs and whether it improves radiologists' diagnostic performance in reading of MMGs. Material and Methods One hundred normal cases for image quality assessment and another 100 cases (50 normal and 50 cancers) for observer performance assessment were enrolled. All mammograms were examined with and without ACM. Five radiologists assessed the intra- and extra-mammary contrast of 100 normal MMGs, and the mean scores of the intra- and extra-mammary contrast were compared between MMGs with and without ACM in both the dense and non-dense group. They classified 100 MMGs into BI-RADS categories 1-5, and were asked to rate the images on a scale of 0 to 100 for the likelihood of the presence of category 3-5 lesions in each breast. Detectability of breast cancer, reading time, and frequency of window adjustment were compared between MMGs with and without ACM. Results ACM improved the intra-mammary contrast in both the dense and non-dense group but degraded extra-mammary contrast in the dense group. There was no significant difference in detectability of breast cancer between MMGs with and without ACM. Frequency of window adjustment without ACM was significantly higher than that with ACM. Reading time without ACM was significantly longer than that with ACM. Conclusion ACM improves the image contrast of MMGs and shortens reading time.

  12. Development and first application of an Aerosol Collection Module (ACM) for quasi online compound specific aerosol measurements

    NASA Astrophysics Data System (ADS)

    Hohaus, Thorsten; Kiendler-Scharr, Astrid; Trimborn, Dagmar; Jayne, John; Wahner, Andreas; Worsnop, Doug

    2010-05-01

    Atmospheric aerosols influence climate and human health on regional and global scales (IPCC, 2007). In many environments organics are a major fraction of the aerosol influencing its properties. Due to the huge variety of organic compounds present in atmospheric aerosol current measurement techniques are far from providing a full speciation of organic aerosol (Hallquist et al., 2009). The development of new techniques for compound specific measurements with high time resolution is a timely issue in organic aerosol research. Here we present first laboratory characterisations of an aerosol collection module (ACM) which was developed to allow for the sampling and transfer of atmospheric PM1 aerosol. The system consists of an aerodynamic lens system focussing particles on a beam. This beam is directed to a 3.4 mm in diameter surface which is cooled to -30 °C with liquid nitrogen. After collection the aerosol sample can be evaporated from the surface by heating it to up to 270 °C. The sample is transferred through a 60cm long line with a carrier gas. In order to test the ACM for linearity and sensitivity we combined it with a GC-MS system. The tests were performed with octadecane aerosol. The octadecane mass as measured with the ACM-GC-MS was compared versus the mass as calculated from SMPS derived total volume. The data correlate well (R2 0.99, slope of linear fit 1.1) indicating 100 % collection efficiency. From 150 °C to 270 °C no effect of desorption temperature on transfer efficiency could be observed. The ACM-GC-MS system was proven to be linear over the mass range 2-100 ng and has a detection limit of ~ 2 ng. First experiments applying the ACM-GC-MS system were conducted at the Jülich Aerosol Chamber. Secondary organic aerosol (SOA) was formed from ozonolysis of 600 ppbv of b-pinene. The major oxidation product nopinone was detected in the aerosol and could be shown to decrease from 2 % of the total aerosol to 0.5 % of the aerosol over the 48 hours of

  13. A Prediction of the Damping Properties of Hindered Phenol AO-60/polyacrylate Rubber (AO-60/ACM) Composites through Molecular Dynamics Simulation

    NASA Astrophysics Data System (ADS)

    Yang, Da-Wei; Zhao, Xiu-Ying; Zhang, Geng; Li, Qiang-Guo; Wu, Si-Zhu

    2016-05-01

    Molecule dynamics (MD) simulation, a molecular-level method, was applied to predict the damping properties of AO-60/polyacrylate rubber (AO-60/ACM) composites before experimental measures were performed. MD simulation results revealed that two types of hydrogen bond, namely, type A (AO-60) -OH•••O=C- (ACM), type B (AO-60) - OH•••O=C- (AO-60) were formed. Then, the AO-60/ACM composites were fabricated and tested to verify the accuracy of the MD simulation through dynamic mechanical thermal analysis (DMTA). DMTA results showed that the introduction of AO-60 could remarkably improve the damping properties of the composites, including the increase of glass transition temperature (Tg) alongside with the loss factor (tan δ), also indicating the AO-60/ACM(98/100) had the best damping performance amongst the composites which verified by the experimental.

  14. A functional collagen adhesin gene, acm, in clinical isolates of Enterococcus faecium correlates with the recent success of this emerging nosocomial pathogen.

    PubMed

    Nallapareddy, Sreedhar R; Singh, Kavindra V; Okhuysen, Pablo C; Murray, Barbara E

    2008-09-01

    Enterococcus faecium recently evolved from a generally avirulent commensal into a multidrug-resistant health care-associated pathogen causing difficult-to-treat infections, but little is known about the factors responsible for this change. We previously showed that some E. faecium strains express a cell wall-anchored collagen adhesin, Acm. Here we analyzed 90 E. faecium isolates (99% acm(+)) and found that the Acm protein was detected predominantly in clinically derived isolates, while the acm gene was present as a transposon-interrupted pseudogene in 12 of 47 isolates of nonclinical origin. A highly significant association between clinical (versus fecal or food) origin and collagen adherence (P Acm detected by whole-cell enzyme-linked immunosorbent assay and flow cytometry. Thirty-seven of 41 sera from patients with E. faecium infections showed reactivity with recombinant Acm, while only 4 of 30 community and hospitalized patient control group sera reacted (P Acm were present in all 14 E. faecium endocarditis patient sera. Although pulsed-field gel electrophoresis indicated that multiple strains expressed collagen adherence, multilocus sequence typing demonstrated that the majority of collagen-adhering isolates, as well as 16 of 17 endocarditis isolates, are part of the hospital-associated E. faecium genogroup referred to as clonal complex 17 (CC17), which has emerged globally. Taken together, our findings support the hypothesis that Acm has contributed to the emergence of E. faecium and CC17 in nosocomial infections.

  15. Insights into Degron Recognition by APC/C Coactivators from the Structure of an Acm1-Cdh1 Complex

    PubMed Central

    He, Jun; Chao, William C.H.; Zhang, Ziguo; Yang, Jing; Cronin, Nora; Barford, David

    2013-01-01

    Summary The anaphase-promoting complex/cyclosome (APC/C) regulates sister chromatid segregation and the exit from mitosis. Selection of most APC/C substrates is controlled by coactivator subunits (either Cdc20 or Cdh1) that interact with substrate destruction motifs—predominantly the destruction (D) box and KEN box degrons. How coactivators recognize D box degrons and how this is inhibited by APC/C regulatory proteins is not defined at the atomic level. Here, from the crystal structure of S. cerevisiae Cdh1 in complex with its specific inhibitor Acm1, which incorporates D and KEN box pseudosubstrate motifs, we describe the molecular basis for D box recognition. Additional interactions between Acm1 and Cdh1 identify a third protein-binding site on Cdh1 that is likely to confer coactivator-specific protein functions including substrate association. We provide a structural rationalization for D box and KEN box recognition by coactivators and demonstrate that many noncanonical APC/C degrons bind APC/C coactivators at the D box coreceptor. PMID:23707760

  16. Superfund Record of Decision (EPA Region 5): Acme Solvent Reclaiming, Winnebago County, IL. (Second remedial action), December 1990

    SciTech Connect

    Not Available

    1990-12-31

    The 20-acre Acme Solvent Reclaiming site is a former industrial disposal site in Winnebago County, Illinois. Land use in the area is mixed agricultural and residential. From 1960 to 1973, Acme Solvent Reclaiming disposed of paints, oils, and still bottoms onsite from its solvent reclamation plant. Wastes were dumped into depressions created from previous quarrying and landscaping operations, and empty drums also were stored onsite. State investigations in 1981 identified elevated levels of chlorinated organic compounds in ground water. A 1985 Record of Decision (ROD) provided for excavation and onsite incineration of 26,000 cubic yards of contaminated soil and sludge, supplying home carbon treatment units to affected residences, and further study of ground water and bedrock. During illegal removal actions taken by PRPs in 1986, 40,000 tons of soil and sludge were removed from the site. The selected remedial action for the site includes excavating and treating 6,000 tons of soil and sludge from two waste areas, using low-temperature thermal stripping; treating residuals using solidification, if necessary, followed by onsite or offsite disposal; treating the remaining contaminated soil and possibly bedrock using soil/bedrock vapor extraction; consolidating the remaining contaminated soil onsite with any treatment residuals, followed by capping; incinerating offsite 8,000 gallons of liquids and sludge from two remaining tanks, and disposing of the tanks offsite; providing an alternate water supply to residents with contaminated wells; pumping and onsite treatment of VOC-contaminated ground water.

  17. ACM-based automatic liver segmentation from 3-D CT images by combining multiple atlases and improved mean-shift techniques.

    PubMed

    Ji, Hongwei; He, Jiangping; Yang, Xin; Deklerck, Rudi; Cornelis, Jan

    2013-05-01

    In this paper, we present an autocontext model(ACM)-based automatic liver segmentation algorithm, which combines ACM, multiatlases, and mean-shift techniques to segment liver from 3-D CT images. Our algorithm is a learning-based method and can be divided into two stages. At the first stage, i.e., the training stage, ACM is performed to learn a sequence of classifiers in each atlas space (based on each atlas and other aligned atlases). With the use of multiple atlases, multiple sequences of ACM-based classifiers are obtained. At the second stage, i.e., the segmentation stage, the test image will be segmented in each atlas space by applying each sequence of ACM-based classifiers. The final segmentation result will be obtained by fusing segmentation results from all atlas spaces via a multiclassifier fusion technique. Specially, in order to speed up segmentation, given a test image, we first use an improved mean-shift algorithm to perform over-segmentation and then implement the region-based image labeling instead of the original inefficient pixel-based image labeling. The proposed method is evaluated on the datasets of MICCAI 2007 liver segmentation challenge. The experimental results show that the average volume overlap error and the average surface distance achieved by our method are 8.3% and 1.5 m, respectively, which are comparable to the results reported in the existing state-of-the-art work on liver segmentation.

  18. CLIC-ACM: generic modular rad-hard data acquisition system based on CERN GBT versatile link

    NASA Astrophysics Data System (ADS)

    Bielawski, B.; Locci, F.; Magnoni, S.

    2015-01-01

    CLIC is a world-wide collaboration to study the next ``terascale'' lepton collider, relying upon a very innovative concept of two-beam-acceleration. This accelerator, currently under study, will be composed of the subsequence of 21000 two-beam-modules. Each module requires more than 300 analogue and digital signals which need to be acquired and controlled in a synchronous way. CLIC-ACM (Acquisition and Control Module) is the 'generic' control and acquisition module developed to accommodate the controls of all these signals for various sub-systems and related specification in term of data bandwidth, triggering and timing synchronization. This paper describes the system architecture with respect to its radiation-tolerance, power consumption and scalability.

  19. Annual evaporite deposition at the acme of the Messinian salinity crisis: evidence for solar-lunar climate forcing

    NASA Astrophysics Data System (ADS)

    Manzi, Vinicio; Gennari, Rocco; Lugli, Stefano; Roveri, Marco; Scafetta, Nicola; Schreiber, B. Charlotte

    2013-04-01

    We studied two evaporite successions (one halite and the other gypsum) consisting of annual varves in order to reconstruct the paleoclimatic and paleoenvironmental conditions existing during the acme of the Messinian salinity crisis (MSC; ≈5.5 Ma), when huge volumes of evaporites accumulated on the floor of the Mediterranean basin. The spectral analyses of these varved evaporitic successions reveal significant peaks in periodicity at around 3-5, 9, 11-13, 20-27 and 50-100 yr. The deposition of varved sedimentary deposits is usually controlled by climate conditions. A comparison with modern precipitation data in the western Mediterranean shows that during the acme of the MSC the climate was not in a permanent evaporitic stage, but in a dynamic state where evaporite deposition was controlled by quasi-periodic climate oscillations similar to modern analogs including Quasi-Biennial Oscillation, El Niño Southern Oscillation, and decadal to secular lunar- and solar-induced cycles. Particularly, we found a significant quasi-decadal oscillation with a prominent 9-year peak that is also common in modern temperature records and is present in both the contemporary Atlantic Multidecadal Oscillation (AMO) index and Pacific Decadal Oscillation (PDO) index. These cyclical patterns are common to both ancient and modern climate records because they can be associated with solar and solar-lunar tidal cycles. During the Messinian, the Mediterranean basin as well as the global ocean, were characterized by somewhat different continent distribution, ocean size, geography, hydrological connections, and ice-sheet volume with respect to the modern configuration. The recognition of modern-style climate oscillations during the Messinian, however, suggests that, although local geographic factors acted as pre-conditioning factors turning the Mediterranean Sea into a giant brine pool, external climate forcing, regulated by solar-lunar cycles and largely independent of those local geographic

  20. Characterization of PVL/ACME-positive methicillin-resistant Staphylococcus aureus (genotypes ST8-MRSA-IV and ST5-MRSA-II) isolated from a university hospital in Japan.

    PubMed

    Kawaguchiya, Mitsuyo; Urushibara, Noriko; Yamamoto, Dai; Yamashita, Toshiharu; Shinagawa, Masaaki; Watanabe, Naoki; Kobayashi, Nobumichi

    2013-02-01

    The ST8 methicillin-resistant Staphylococcus aureus (MRSA) with Staphylococcal cassette chromosome mec (SCCmec) type IVa, known as USA300, is a prevalent community-acquired MRSA (CA-MRSA) clone in the United States and has been spreading worldwide. The USA300 characteristically harbors Panton-Valentine Leukocidin (PVL) genes and the arginine catabolic mobile element (ACME, type I). Prevalence and molecular characteristics of PVL(+) and/or ACME(+) S. aureus were investigated in a university hospital located in northern Japan, for 1,366 S. aureus isolates, including 601 MRSA strains derived from clinical specimens collected from 2008 to 2010. The PVL gene was identified in three MRSA strains with SCCmec IV, which belonged to ST8, spa type t008, coagulase type III, and agr type I. Two PVL-positive MRSA strains had also type I ACME, and were isolated from skin abscess of outpatients who have not travelled abroad recently. One of these PVL(+)/ACME(+) strains carried tet(K), msrA, and aph(3')-IIIa, showing resistance to kanamycin, tetracycline, erythromycin, and ciprofloxacin, suggesting acquisition of more resistance than ST8 CA-MRSA reported in Japan previously. In contrast, another PVL(+)/ACME(+) strain and a PVL(+)/ACME(-) strain were susceptible to more antimicrobials and had less virulence factors than PVL(-)/ACME(+) MRSA strains. Besides the two PVL(+) MRSA strains, ACME (type-ΔII) was identified into seven MRSA strains with SCCmec II belonging to ST5, one of the three spa types (t002, t067, and t071), coagulase type II, and agr type II. These PVL(-)/ACME(+) MRSA strains showed multiple drug resistance and harbored various toxin genes as observed for ST5 PVL(-)/ACME(-) MRSA-II. The present study suggested the spread of ST8-MRSA-IV in northern Japan, and a potential significance of ACME-positive ST5-MRSA-II as an emerging MRSA clone in a hospital.

  1. Proceeding of the ACM/IEEE-CS Joint Conference on Digital Libraries (1st, Roanoke, Virginia, June 24-28, 2001).

    ERIC Educational Resources Information Center

    Association for Computing Machinery, New York, NY.

    Papers in this Proceedings of the ACM/IEEE-CS Joint Conference on Digital Libraries (Roanoke, Virginia, June 24-28, 2001) discuss: automatic genre analysis; text categorization; automated name authority control; automatic event generation; linked active content; designing e-books for legal research; metadata harvesting; mapping the…

  2. Detection of structural and numerical chromosomal abnormalities by ACM-FISH analysis in sperm of oligozoospermic infertility patients.

    PubMed

    Schmid, T E; Brinkworth, M H; Hill, F; Sloter, E; Kamischke, A; Marchetti, F; Nieschlag, E; Wyrobek, A J

    2004-06-01

    Modern reproductive technologies are enabling the treatment of infertile men with severe disturbances of spermatogenesis. The possibility of elevated frequencies of genetically and chromosomally defective sperm has become an issue of concern with the increased usage of ICSI, which can enable men with severely impaired sperm production to father children. Several papers have been published reporting aneuploidy in oligozoospermic patients, but relatively little is known about chromosome structural aberrations in the sperm of these patients. We examined sperm from infertile, oligozoospermic individuals for structural and numerical chromosomal abnormalities using a multicolour ACM fluorescence in situ hybridization (FISH) assay that utilizes DNA probes specific for three regions of chromosome 1 to detect human sperm that carry numerical chromosomal abnormalities plus two categories of structural aberrations: duplications and deletions of 1pter and 1cen, and chromosomal breaks within the 1cen-1q12 region. There was a significant increase in the average frequencies of sperm with duplications and deletions in the infertility patients compared with the healthy concurrent controls. There was also a significantly elevated level of breaks within the 1cen-1q12 region. There was no evidence for an increase in chromosome 1 disomy, or in diploidy. Our data reveal that oligozoospermia is associated with chromosomal structural abnormalities, suggesting that oligozoospermic men carry a higher burden of transmissible, chromosome damage. The findings raise the possibility of elevated levels of transmissible chromosomal defects following ICSI treatment.

  3. Human factors in computing systems: focus on patient-centered health communication at the ACM SIGCHI conference.

    PubMed

    Wilcox, Lauren; Patel, Rupa; Chen, Yunan; Shachak, Aviv

    2013-12-01

    Health Information Technologies, such as electronic health records (EHR) and secure messaging, have already transformed interactions among patients and clinicians. In addition, technologies supporting asynchronous communication outside of clinical encounters, such as email, SMS, and patient portals, are being increasingly used for follow-up, education, and data reporting. Meanwhile, patients are increasingly adopting personal tools to track various aspects of health status and therapeutic progress, wishing to review these data with clinicians during consultations. These issues have drawn increasing interest from the human-computer interaction (HCI) community, with special focus on critical challenges in patient-centered interactions and design opportunities that can address these challenges. We saw this community presenting and interacting at the ACM SIGCHI 2013, Conference on Human Factors in Computing Systems, (also known as CHI), held April 27-May 2nd, 2013 at the Palais de Congrès de Paris in France. CHI 2013 featured many formal avenues to pursue patient-centered health communication: a well-attended workshop, tracks of original research, and a lively panel discussion. In this report, we highlight these events and the main themes we identified. We hope that it will help bring the health care communication and the HCI communities closer together.

  4. A multicopper oxidase is essential for manganese oxidation and laccase-like activity in Pedomicrobium sp. ACM 3067.

    PubMed

    Ridge, Justin P; Lin, Marianne; Larsen, Eloise I; Fegan, Mark; McEwan, Alastair G; Sly, Lindsay I

    2007-04-01

    Pedomicrobium sp. ACM 3067 is a budding-hyphal bacterium belonging to the alpha-Proteobacteria which is able to oxidize soluble Mn2+ to insoluble manganese oxide. A cosmid, from a whole-genome library, containing the putative genes responsible for manganese oxidation was identified and a primer-walking approach yielded 4350 bp of novel sequence. Analysis of this sequence showed the presence of a predicted three-gene operon, moxCBA. The moxA gene product showed homology to multicopper oxidases (MCOs) and contained the characteristic four copper-binding motifs (A, B, C and D) common to MCOs. An insertion mutation of moxA showed that this gene was essential for both manganese oxidation and laccase-like activity. The moxB gene product showed homology to a family of outer membrane proteins which are essential for Type I secretion in Gram-negative bacteria. moxBA has not been observed in other manganese-oxidizing bacteria but homologues were identified in the genomes of several bacteria including Sinorhizobium meliloti 1021 and Agrobacterium tumefaciens C58. These results suggest that moxBA and its homologues constitute a family of genes encoding an MCO and a predicted component of the Type I secretion system.

  5. Detection of structural and numerical chomosomal abnormalities by ACM-FISH analysis in sperm of oligozoospermic infertility patients

    SciTech Connect

    Schmid, T E; Brinkworth, M H; Hill, F; Sloter, E; Kamischke, A; Marchetti, F; Nieschlag, E; Wyrobek, A J

    2003-11-10

    Modern reproductive technologies are enabling the treatment of infertile men with severe disturbances of spermatogenesis. The possibility of elevated frequencies of genetically and chromosomally defective sperm has become an issue of concern with the increased usage of intracytoplasmic sperm injection (ICSI), which can enable men with severely impaired sperm production to father children. Several papers have been published about aneuploidy in oligozoospermic patients, but relatively little is known about chromosome structural aberrations in the sperm of these patients. We examined sperm from infertile, oligozoospermic individuals for structural and numerical chromosomal abnormalities using a multicolor ACM FISH assay that utilizes DNA probes specific for three regions of chromosome 1 to detect human sperm that carry numerical chromosomal abnormalities plus two categories of structural aberrations: duplications and deletions of 1pter and 1cen, and chromosomal breaks within the 1cen-1q12 region. There was a significant increase in the average frequencies of sperm with duplications and deletions in the infertility patients compared with the healthy concurrent controls. There was also a significantly elevated level of breaks within the 1cen-1q12 region. There was no evidence for an increase in chromosome-1 disomy, or in diploidy. Our data reveal that oligozoospermia is associated with chromosomal structural abnormalities suggesting that, oligozoospermic men carry a higher burden of transmissible, chromosome damage. The findings raise the possibility of elevated levels of transmissible chromosomal defects following ICSI treatment.

  6. Mechanisms of stochastic focusing and defocusing in biological reaction networks: insight from accurate chemical master equation (ACME) solutions.

    PubMed

    Gursoy, Gamze; Terebus, Anna; Youfang Cao; Jie Liang

    2016-08-01

    Stochasticity plays important roles in regulation of biochemical reaction networks when the copy numbers of molecular species are small. Studies based on Stochastic Simulation Algorithm (SSA) has shown that a basic reaction system can display stochastic focusing (SF) by increasing the sensitivity of the network as a result of the signal noise. Although SSA has been widely used to study stochastic networks, it is ineffective in examining rare events and this becomes a significant issue when the tails of probability distributions are relevant as is the case of SF. Here we use the ACME method to solve the exact solution of the discrete Chemical Master Equations and to study a network where SF was reported. We showed that the level of SF depends on the degree of the fluctuations of signal molecule. We discovered that signaling noise under certain conditions in the same reaction network can lead to a decrease in the system sensitivities, thus the network can experience stochastic defocusing. These results highlight the fundamental role of stochasticity in biological reaction networks and the need for exact computation of probability landscape of the molecules in the system.

  7. Hydrologic effects of phreatophyte control, Acme-Artesia reach of the Pecos River, New Mexico, 1967-82

    USGS Publications Warehouse

    Welder, G.E.

    1988-01-01

    The U.S. Bureau of Reclamation began a phreatophyte clearing and control program in the bottom land of the Acme-Artesia reach of the Pecos River in March 1967. The initial cutting of 19,000 acres of saltcedar trees, the dominant phreatophyte in the area, was completed in May 1969. Saltcedar regrowth continued each year until July 1975, when root plowing eradicated most of the regrowth. The major objective of the clearing and control program was to salvage water that could be put to beneficial use. Measurements of changes in the water table in the bottom land and changes in the base flow of the Pecos River were made in order to determine the hydrologic effects of the program. Some salvage of water was indicated, but it is not readily recognized as an increase in base flow. The quantity of salvage probably is less than the average annual base-flow gain of 19 ,110 acre-ft in the reach during 1967-82. (Author 's abstract)

  8. Gradient-based reliability maps for ACM-based segmentation of hippocampus.

    PubMed

    Zarpalas, Dimitrios; Gkontra, Polyxeni; Daras, Petros; Maglaveras, Nicos

    2014-04-01

    Automatic segmentation of deep brain structures, such as the hippocampus (HC), in MR images has attracted considerable scientific attention due to the widespread use of MRI and to the principal role of some structures in various mental disorders. In this literature, there exists a substantial amount of work relying on deformable models incorporating prior knowledge about structures' anatomy and shape information. However, shape priors capture global shape characteristics and thus fail to model boundaries of varying properties; HC boundaries present rich, poor, and missing gradient regions. On top of that, shape prior knowledge is blended with image information in the evolution process, through global weighting of the two terms, again neglecting the spatially varying boundary properties, causing segmentation faults. An innovative method is hereby presented that aims to achieve highly accurate HC segmentation in MR images, based on the modeling of boundary properties at each anatomical location and the inclusion of appropriate image information for each of those, within an active contour model framework. Hence, blending of image information and prior knowledge is based on a local weighting map, which mixes gradient information, regional and whole brain statistical information with a multi-atlas-based spatial distribution map of the structure's labels. Experimental results on three different datasets demonstrate the efficacy and accuracy of the proposed method.

  9. Multi-walled carbon nanotubes/polymer composites in absence and presence of acrylic elastomer (ACM).

    PubMed

    Kumar, S; Rath, T; Mahaling, R N; Mukherjee, M; Khatua, B B; Das, C K

    2009-05-01

    Polyetherimide/Multiwall carbon nanotube (MWNTs) nanocomposites containing as-received and modified (COOH-MWNT) carbon nanotubes were prepared through melt process in extruder and then compression molded. Thermal properties of the composites were characterized by thermo-gravimetric analysis (TGA). Field emission scanning electron microscopy (FESEM) images showed that the MWNTs were well dispersed and formed an intimate contact with the polymer matrix without any agglomeration. However the incorporation of modified carbon nanotubes formed fascinating, highly crosslinked, and compact network structure throughout the polymer matrix. This showed the increased adhesion of PEI with modified MWNTs. Scanning electron microscopy (SEM) also showed high degree of dispersion of modified MWNTs along with broken ends. Dynamic mechanical analysis (DMA) results showed a marginal increase in storage modulus (E') and glass transition temperature (T(g)) with the addition of MWNTs. Increase in tensile strength and impact strength of composites confirmed the use the MWNTs as possible reinforcement agent. Both thermal and electrical conductivity of composites increased, but effect is more pronounced on modification due to formation of network of carbon nanotubes. Addition of acrylic elastomer to developed PEI/MWNTs (modified) nanocomposites resulted in the further increase in thermal and electrical properties due to the formation of additional bond between MWNTs and acrylic elastomers at the interface. All the results presented are well corroborated by SEM and FESEM studies.

  10. WTP Calculation Sheet: Determining the LAW Glass Former Constituents and Amounts for G2 and Acm Models. 24590-LAW-M4C-LFP-00002, Rev. B

    SciTech Connect

    Gimpel, Rodney F.; Kruger, Albert A.

    2013-12-16

    The purpose of this calculation is to determine the LAW glass former recipe and additives with their respective amounts. The methodology and equations contained herein are to be used in the G2 and ACM models until better information is supplied by R&T efforts. This revision includes calculations that determines the mass and volume of the bulk chemicals/minerals needed per batch. Plus, it contains calculations (for the G2 model) to help prevent overflow in LAW Feed Preparation Vessel.

  11. High-resolution, Antarctic Ice Sheet simulations forced by submarine melting simulated by the Accelerated Climate Model for Energy (ACME)

    NASA Astrophysics Data System (ADS)

    Price, S. F.; Asay-Davis, X.; Fyke, J. G.; Hoffman, M. J.; Jacobson, D.; Petersen, M. R.; Tezaur, I.; Perego, M.; Salinger, A.; Turner, A. K.; Wolfe, J.

    2016-12-01

    The capability for simulating sub-ice shelf circulation and submarine melting and freezing has recently been added to the U.S. Department of Energy's Accelerated Climate Model for Energy (ACME). With this new capability, we use an eddy permitting ocean model to conduct two sets of simulations in the spirit of Spence et al. (GRL, 41, 2014), who demonstrate increased warm water upwelling along the Antarctic coast in response to poleward shifting and strengthening of Southern Ocean westerly winds. These characteristics, symptomatic of a positive Southern Annual Model (SAM), are projected to continue into the 21st century under anthropogenic climate change (Fyfe et al., J. Clim., 20, 2007). In our first simulation, we force our climate model using repeat cycles of the standard CORE interannual forcing dataset (Large and Yeager; Clim. Dyn., 33, 2009). These melt rates are used to force our high-resolution (30-to-1 km) ice sheet model, MPAS-Land Ice, offline and to derive a quasi-steady state ice sheet model initial condition. In our second simulation, we force our climate model using an altered version of CORE interannual forcing, based on the latter half of the full time series, which we take as a proxy for a future climate state biased towards a positive SAM. Melt rate anomalies from this second simulation are then used to force our ice sheet model offline out to year 2100. We compare ocean model states and sub-ice shelf melt rates with observations and present estimates for Antarctic Ice Sheet mass loss from our simulations.

  12. Significant impacts of irrigation water sources and methods on modeling irrigation effects in the ACME Land Model

    DOE PAGES

    Leng, Guoyong; Leung, Lai-Yung; Huang, Maoyi

    2017-07-01

    An irrigation module that considers both irrigation water sources and irrigation methods has been incorporated into the ACME Land Model (ALM). Global numerical experiments were conducted to evaluate the impacts of irrigation water sources and irrigation methods on the simulated irrigation effects. All simulations shared the same irrigation soil moisture target constrained by a global census dataset of irrigation amounts. Irrigation has large impacts on terrestrial water balances especially in regions with extensive irrigation. Such effects depend on the irrigation water sources: surface-water-fed irrigation leads to decreases in runoff and water table depth, while groundwater-fed irrigation increases water table depth,more » with positive or negative effects on runoff depending on the pumping intensity. Irrigation effects also depend significantly on the irrigation methods. Flood irrigation applies water in large volumes within short durations, resulting in much larger impacts on runoff and water table depth than drip and sprinkler irrigations. Differentiating the irrigation water sources and methods is important not only for representing the distinct pathways of how irrigation influences the terrestrial water balances, but also for estimating irrigation water use efficiency. Specifically, groundwater pumping has lower irrigation water use efficiency due to enhanced recharge rates. Different irrigation methods also affect water use efficiency, with drip irrigation the most efficient followed by sprinkler and flood irrigation. Our results highlight the importance of explicitly accounting for irrigation sources and irrigation methods, which are the least understood and constrained aspects in modeling irrigation water demand, water scarcity and irrigation effects in Earth System Models.« less

  13. A 90-day subchronic feeding study of genetically modified maize expressing Cry1Ac-M protein in Sprague-Dawley rats.

    PubMed

    Liu, Pengfei; He, Xiaoyun; Chen, Delong; Luo, Yunbo; Cao, Sishuo; Song, Huan; Liu, Ting; Huang, Kunlun; Xu, Wentao

    2012-09-01

    The cry1Ac-M gene, coding one of Bacillus thuringiensis (Bt) crystal proteins, was introduced into maize H99 × Hi IIB genome to produce insect-resistant GM maize BT-38. The food safety assessment of the BT-38 maize was conducted in Sprague-Dawley rats by a 90-days feeding study. We incorporated maize grains from BT-38 and H99 × Hi IIB into rodent diets at three concentrations (12.5%, 25%, 50%) and administered to Sprague-Dawley rats (n=10/sex/group) for 90 days. A commercialized rodent diet was fed to an additional group as control group. Body weight, feed consumption and toxicological response variables were measured, and gross as well as microscopic pathology were examined. Moreover, detection of residual Cry1Ac-M protein in the serum of rats fed with GM maize was conducted. No death or adverse effects were observed in the current feeding study. No adverse differences in the values of the response variables were observed between rats that consumed diets containing GM maize BT-38 and non-GM maize H99 × Hi IIB. No detectable Cry1Ac-M protein was found in the serum of rats after feeding diets containing GM maize for 3 months. The results demonstrated that BT-38 maize is as safe as conventional non-GM maize.

  14. Prescriptions for ACME's Future.

    ERIC Educational Resources Information Center

    Felch, William Campbell

    1991-01-01

    Five prescriptions for the future agenda of the Alliance for Continuing Medical Education are (1) a core curriculum; (2) informatics; (3) remedial continuing medical education (CME); (4) focus on the individual learner; and (5) practice-oriented CME. (SK)

  15. Acme Landfill Expansion. Appendices.

    DTIC Science & Technology

    1982-01-01

    connected to that supply shall be clearly labeled in English, "Polluted-Not Safe For Human Use", and Spanish, "Peligro, Contaminacion , No Usar". 7. Public...8217 Grab0, smiz1lc quarterly’ watur le~vel f -Vt Stationls throu(’,iout Lhe year Col or visual chloride 1. ’i tira te D i trolyen u)j/ K j : 1d;d 1 .1j/ J i t

  16. Representing carbon, nitrogen, and phosphorus interaction in the ACME Land Model v1: model development and global benchmarking

    NASA Astrophysics Data System (ADS)

    Zhu, Q.; Riley, W. J.; Tang, J.; Hoffman, F. M.; Mu, M.; Randerson, J. T.

    2016-12-01

    Since nutrient limitations of the terrestrial carbon cycle have been rigorously demonstrated by field experiments (e.g., fertilization experiments), various Earth System Model (ESM) groups have spent substantial effort to incorporate nutrient sub-models in their terrestrial carbon cycle models (e.g., CLM-CNP, JSBACH-CNP, CABLE-CNP). Here we report new developments in the Accelerated Climate Modeling for Energy (ACME) Land Model (ALMv1) regarding carbon-nutrient interactions. The development is based on (1) recent theoretical advances in understanding belowground multiple-consumer, multiple-nutrient competition; (2) a dynamic allocation scheme based on resources availability to balance whole system functioning; and (3) global datasets of plant physiological traits (e.g., TRY database). In addition to describing these developments, we compare them with representations in other ESM land models. We demonstrate that these new ALMv1 developments accurately reproduce present terrestrial carbon dynamics under the constraints of nitrogen and phosphorus availability. We benchmark the new model using the International Land Model Benchmarking package (ILAMB) for major plant and soil carbon pools (total vegetation biomass, soil carbon content) and fluxes (GPP, NEP) and leaf area index (LAI). The results show that biases have been significantly reduced (e.g., GPP bias in boreal needle leaf forests, LAI bias in tropical broad leaf evergreen forests). The ILAMB benchmarks provide a unique opportunity to consistently track ongoing model development and simultaneously demonstrate improvements for multiple variables. We further benchmark the new model transient response to nutrient perturbation, using nitrogen and phosphorus fertilization experiments at over 100 forest sites. We found that the plant productivity response ratio ((NPPfert - NPPcontrol)/ NPPcontrol) could be captured only when the whole system functional balance is taken into account. Compared with other candidate

  17. Design of ET(B) receptor agonists: NMR spectroscopic and conformational studies of ET7-21[Leu7, Aib11, Cys(Acm)15].

    PubMed

    Hewage, Chandralal M; Jiang, Lu; Parkinson, John A; Ramage, Robert; Sadler, Ian H

    2002-03-01

    In a previous report we have shown that the endothelin-B receptor-selective linear endothelin peptide, ET-1[Cys (Acm)1,15, Ala3, Leu7, Aib11], folds into an alpha-helical conformation in a methanol-d3/water co-solvent [Hewage et al. (1998) FEBS Lett., 425, 234-238]. To study the requirements for the structure-activity relationships, truncated analogues of this peptide were subjected to further studies. Here we report the solution conformation of ET7-21[Leu7, Aib11, Cys(Acm)15], in a methanol-d3/water co-solvent at pH 3.6, by NMR spectroscopic and molecular modelling studies. Further truncation of this short peptide results in it displaying poor agonist activity. The modelled structure shows that the peptide folds into an alpha-helical conformation between residues Lys9-His16, whereas the C-terminus prefers no fixed conformation. This truncated linear endothelin analogue is pivotal for designing endothelin-B receptor agonists.

  18. Enterococcus faecium biofilm formation: identification of major autolysin AtlAEfm, associated Acm surface localization, and AtlAEfm-independent extracellular DNA Release.

    PubMed

    Paganelli, Fernanda L; Willems, Rob J L; Jansen, Pamela; Hendrickx, Antoni; Zhang, Xinglin; Bonten, Marc J M; Leavis, Helen L

    2013-04-16

    Enterococcus faecium is an important multidrug-resistant nosocomial pathogen causing biofilm-mediated infections in patients with medical devices. Insight into E. faecium biofilm pathogenesis is pivotal for the development of new strategies to prevent and treat these infections. In several bacteria, a major autolysin is essential for extracellular DNA (eDNA) release in the biofilm matrix, contributing to biofilm attachment and stability. In this study, we identified and functionally characterized the major autolysin of E. faecium E1162 by a bioinformatic genome screen followed by insertional gene disruption of six putative autolysin genes. Insertional inactivation of locus tag EfmE1162_2692 resulted in resistance to lysis, reduced eDNA release, deficient cell attachment, decreased biofilm, decreased cell wall hydrolysis, and significant chaining compared to that of the wild type. Therefore, locus tag EfmE1162_2692 was considered the major autolysin in E. faecium and renamed atlAEfm. In addition, AtlAEfm was implicated in cell surface exposure of Acm, a virulence factor in E. faecium, and thereby facilitates binding to collagen types I and IV. This is a novel feature of enterococcal autolysins not described previously. Furthermore, we identified (and localized) autolysin-independent DNA release in E. faecium that contributes to cell-cell interactions in the atlAEfm mutant and is important for cell separation. In conclusion, AtlAEfm is the major autolysin in E. faecium and contributes to biofilm stability and Acm localization, making AtlAEfm a promising target for treatment of E. faecium biofilm-mediated infections. IMPORTANCE Nosocomial infections caused by Enterococcus faecium have rapidly increased, and treatment options have become more limited. This is due not only to increasing resistance to antibiotics but also to biofilm-associated infections. DNA is released in biofilm matrix via cell lysis, caused by autolysin, and acts as a matrix stabilizer. In this study

  19. Three-dimensional neural differentiation of embryonic stem cells with ACM induction in microfibrous matrices in bioreactors.

    PubMed

    Liu, Ning; Ouyang, Anli; Li, Yan; Yang, Shang-Tian

    2013-01-01

    The clinical use of pluripotent stem cell (PSC)-derived neural cells requires an efficient differentiation process for mass production in a bioreactor. Toward this goal, neural differentiation of murine embryonic stem cells (ESCs) in three-dimensional (3D) polyethylene terephthalate microfibrous matrices was investigated in this study. To streamline the process and provide a platform for process integration, the neural differentiation of ESCs was induced with astrocyte-conditioned medium without the formation of embryoid bodies, starting from undifferentiated ESC aggregates expanded in a suspension bioreactor. The 3D neural differentiation was able to generate a complex neural network in the matrices. When compared to 2D differentiation, 3D differentiation in microfibrous matrices resulted in a higher percentage of nestin-positive cells (68% vs. 54%) and upregulated gene expressions of nestin, Nurr1, and tyrosine hydroxylase. High purity of neural differentiation in 3D microfibrous matrix was also demonstrated in a spinner bioreactor with 74% nestin + cells. This study demonstrated the feasibility of a scalable process based on 3D differentiation in microfibrous matrices for the production of ESC-derived neural cells.

  20. Exploring Group Communication and Productivity Improvement: Using an Experiential Process.

    ERIC Educational Resources Information Center

    Mandeville, Mary Y.; Mandeville, David E.

    Engineering students at Oklahoma State University used an experiential process (the ACME Basket Exercise) to develop an understanding of how quality and productivity can be improved. The exercise simulates a traditional production organization in the classroom and mirrors the efforts, the successes, and the frustrations of individuals and work…

  1. Teachers' Planning Processes: Seeking Insights from Australian Teachers

    ERIC Educational Resources Information Center

    Sullivan, Peter; Clarke, Doug M.; Albright, James; Clarke, David J.; Farrell, Lesley; Freebody, Peter; Gerrard, Jessica; Michels, Deborah

    2012-01-01

    The Australian Curriculum: Mathematics (AC:M) prompts consideration of planning processes teachers typically use (as a whole school, in grade levels, and at the classroom level). In order to gain insights into the nature of the planning decisions teachers make, Australian teachers drawn from every state and territory were invited to respond to a…

  2. Eliciting a Sensemaking Process from Verbal Protocols of Reverse Engineers

    DTIC Science & Technology

    2012-08-01

    processing loop used in pro- gramming artificial agents to interface with an environment (S. Russell & Norvig , 2003), with the addition of a state to...Human factors in computing sys- tems (CHI93) (pp. 269–276). New York, New York, USA: ACM Press. Russell, S., & Norvig , P. (2003). Artificial Intelligence

  3. Construction of improved temperature-sensitive and mobilizable vectors and their use for constructing mutations in the adhesin-encoding acm gene of poorly transformable clinical Enterococcus faecium strains.

    PubMed

    Nallapareddy, Sreedhar R; Singh, Kavindra V; Murray, Barbara E

    2006-01-01

    Inactivation by allelic exchange in clinical isolates of the emerging nosocomial pathogen Enterococcus faecium has been hindered by lack of efficient tools, and, in this study, transformation of clinical isolates was found to be particularly problematic. For this reason, a vector for allelic replacement (pTEX5500ts) was constructed that includes (i) the pWV01-based gram-positive repAts replication region, which is known to confer a high degree of temperature intolerance, (ii) Escherichia coli oriR from pUC18, (iii) two extended multiple-cloning sites located upstream and downstream of one of the marker genes for efficient cloning of flanking regions for double-crossover mutagenesis, (iv) transcriptional terminator sites to terminate undesired readthrough, and (v) a synthetic extended promoter region containing the cat gene for allelic exchange and a high-level gentamicin resistance gene, aph(2'')-Id, to distinguish double-crossover recombination, both of which are functional in gram-positive and gram-negative backgrounds. To demonstrate the functionality of this vector, the vector was used to construct an acm (encoding an adhesin to collagen from E. faecium) deletion mutant of a poorly transformable multidrug-resistant E. faecium endocarditis isolate, TX0082. The acm-deleted strain, TX6051 (TX0082Deltaacm), was shown to lack Acm on its surface, which resulted in the abolishment of the collagen adherence phenotype observed in TX0082. A mobilizable derivative (pTEX5501ts) that contains oriT of Tn916 to facilitate conjugative transfer from the transformable E. faecalis strain JH2Sm::Tn916 to E. faecium was also constructed. Using this vector, the acm gene of a nonelectroporable E. faecium wound isolate was successfully interrupted. Thus, pTEX5500ts and its mobilizable derivative demonstrated their roles as important tools by helping to create the first reported allelic replacement in E. faecium; the constructed this acm deletion mutant will be useful for assessing the

  4. Spin–orbit torque switching in MgO/CoFeB/Ta/CoFeB/MgO heterostructures with a critical current density of 105 A/cm2

    NASA Astrophysics Data System (ADS)

    Shi, Guoyi; Chang, Yuansi; Cai, Jianwang; Zhang, Pengxiang; Pan, Feng; Song, Cheng

    2017-10-01

    Spin–orbit torque-induced magnetization switching in heavy metal/ferromagnetic metal/oxide heterostructures has been extensively studied. However, thus far, the critical current density for magnetization switching in these systems is at least ∼106 A/cm2. Here, we investigate the spin–orbit torque switching in a substrate/MgO/CoFeB/Ta/CoFeB/MgO structure where the upper CoFeB layer exhibits a strong perpendicular magnetic anisotropy in contrast to the relatively weak perpendicular anisotropy in the lower CoFeB layer. By varying the thickness of Ta, we observe that the critical current required for switching differs markedly. Specifically, for the sample with a 3-nm-thick Ta layer, with an external field of 100 Oe applied along the current direction to break the symmetry, the critical current density is ∼2 × 105 A/cm2. This could be ascribed to the minimum coercivity and perpendicular anisotropic field in the sample with a 3-nm-thick Ta layer.

  5. Immature osteoblastic MG63 cells possess two calcitonin gene-related peptide receptor subtypes that respond differently to [Cys(Acm)(2,7)] calcitonin gene-related peptide and CGRP(8-37).

    PubMed

    Kawase, Tomoyuki; Okuda, Kazuhiro; Burns, Douglas M

    2005-10-01

    Calcitonin gene-related peptide (CGRP) is clearly an anabolic factor in skeletal tissue, but the distribution of CGRP receptor (CGRPR) subtypes in osteoblastic cells is poorly understood. We previously demonstrated that the CGRPR expressed in osteoblastic MG63 cells does not match exactly the known characteristics of the classic subtype 1 receptor (CGRPR1). The aim of the present study was to further characterize the MG63 CGRPR using a selective agonist of the putative CGRPR2, [Cys(Acm)(2,7)]CGRP, and a relatively specific antagonist of CGRPR1, CGRP(8-37). [Cys(Acm)(2,7)]CGRP acted as a significant agonist only upon ERK dephosphorylation, whereas this analog effectively antagonized CGRP-induced cAMP production and phosphorylation of cAMP response element-binding protein (CREB) and p38 MAPK. Although it had no agonistic action when used alone, CGRP(8-37) potently blocked CGRP actions on cAMP, CREB, and p38 MAPK but had less of an effect on ERK. Schild plot analysis of the latter data revealed that the apparent pA2 value for ERK is clearly distinguishable from those of the other three plots as judged using the 95% confidence intervals. Additional assays using 3-isobutyl-1-methylxanthine or the PKA inhibitor N-(2-[p-bromocinnamylamino]ethyl)-5-isoquinolinesulfonamide hydrochloride (H-89) indicated that the cAMP-dependent pathway was predominantly responsible for CREB phosphorylation, partially involved in ERK dephosphorylation, and not involved in p38 MAPK phosphorylation. Considering previous data from Scatchard analysis of [125I]CGRP binding in connection with these results, these findings suggest that MG63 cells possess two functionally distinct CGRPR subtypes that show almost identical affinity for CGRP but different sensitivity to CGRP analogs: one is best characterized as a variation of CGRPR1, and the second may be a novel variant of CGRPR2.

  6. The effect of changing wind forcing on Antarctic ice shelf melting in high-resolution, global sea ice-ocean simulations with the Accelerated Climate Model for Energy (ACME)

    NASA Astrophysics Data System (ADS)

    Asay-Davis, Xylar; Price, Stephen; Petersen, Mark; Wolfe, Jonathan

    2017-04-01

    The capability for simulating sub-ice shelf circulation and submarine melting and freezing has recently been added to the U.S. Department of Energy's Accelerated Climate Model for Energy (ACME). With this new capability, we use an eddy permitting ocean model to conduct two sets of simulations in the spirit of Spence et al. (GRL, 41, 2014), who demonstrate increased warm water upwelling along the Antarctic coast in response to poleward shifting and strengthening of Southern Ocean westerly winds. These characteristics, symptomatic of a positive Southern Annular Mode (SAM), are projected to continue into the 21st century under anthropogenic climate change (Fyfe et al., J. Clim., 20, 2007). In our first simulation, we force the climate model using the standard CORE interannual forcing dataset (Large and Yeager; Clim. Dyn., 33, 2009). In our second simulation, we force our climate model using an altered version of CORE interannual forcing, based on the latter half of the full time series, which we take as a proxy for a future climate state biased towards a positive SAM. We compare ocean model states and sub-ice shelf melt rates with observations, exploring sources of model biases as well as the effects of the two forcing scenarios.

  7. INTEGRATED PROCESS GAS MODELING FOR TRITIUM SYSTEMS AT THE SAVANNAH RIVER SITE

    SciTech Connect

    Hang, T; Anita Poore, A

    2007-08-30

    Significant savings are being realized from the consolidated tritium gas-processing operations at the Savannah River Site. However, the trade-off is some reduction of operational flexibility due to decreased storage capacity for process and waste gases. Savannah River National Laboratory researchers are developing an integrated process gas model for tritium processing using Aspen Custom Modeler{trademark} (ACM) software. The modeling involves fully characterizing process flow streams (gas composition, quantity), frequency of batch transfers, and availability of equipment in the flow stream. The model provides a valuable engineering tool to identify flow bottlenecks, thereby enabling adjustments to be made to improve process operations.

  8. Electromagnetic mixed waste processing system for asbestos decontamination

    SciTech Connect

    Kasevich, R.S.; Vaux, W.; Ulerich, N.; Nocito, T.

    1996-12-31

    The overall objective of this three-phase program is to develop an integrated process for treating asbestos-containing material that is contaminated with radioactive and hazardous constituents. The integrated process will attempt to minimize processing and disposal costs. The objectives of Phase 1 were to establish the technical feasibility of asbestos decomposition, inorganic radionuclide nd heavy metal removal, and organic volatilization. Phase 1 resulted in the successful bench-scale demonstration of the elements required to develop a mixed waste treatment process for asbestos-containing material (ACM) contaminated with radioactive metals, heavy metals, and organics. Using the Phase 1 data, a conceptual process was developed. The Phase 2 program, currently in progress, is developing an integrated system design for ACM waste processing. The Phase 3 program will target demonstration of the mixed waste processing system at a DOE facility. The electromagnetic mixed waste processing system employs patented technologies to convert DOE asbestos to a non-hazardous, radionuclide-free, stable waste. The dry, contaminated asbestos is initially heated with radiofrequency energy to remove organic volatiles. Second,the radionuclides are removed by solvent extraction coupled with ion exchange solution treatment. Third, the ABCOV method converts the asbestos to an amorphous silica suspension at low temperature (100{degrees}C). Finally the amorphous silica is solidified for disposal.

  9. The ACM Periodical Bank: A Retrospective View.

    ERIC Educational Resources Information Center

    Clarke, Jack A.

    1980-01-01

    Evaluates a cooperative venture in interlibrary lending of periodicals planned and executed by ten midwestern colleges. The study traces the consortium's history from 1967 to the present, describing successes and problems. (RAA)

  10. The Acme of Skill: Nonkinetic Warfare

    DTIC Science & Technology

    2008-05-01

    frontmatter.indd 6 7/29/08 12:15:43 PM Introduction The term nonkinetic warfare may seem to be an oxy- moron . How can warfare be described as...the hallmark of the previous two genera- tions of warfare. The authors attribute the evolution of warfare largely to the advancement in technology and

  11. Continuous- and batch-processed MgB 2/Fe strands--transport and magnetic properties

    NASA Astrophysics Data System (ADS)

    Collings, E. W.; Lee, E.; Sumption, M. D.; Tomsic, M.; Wang, X. L.; Soltanian, S.; Dou, S. X.

    2003-04-01

    The tube filling/forming powder-in-tube (PIT) technique was employed at Hyper Tech Research for the continuous processing of MgB 2/Fe composite strand. Demonstration lengths of up to 70 m of 1.2 mm diameter precursor strand--an Fe-clad Mg + B elemental powder mixture--have so far been produced. Short samples of this strand, heat treated for 3-30 min/800-950 °C, have yielded transport critical current densities ( Jc) of 2-3×10 4 A/cm 2 at 4 K/4 T, 4×10 4 A/cm 2 at 4 K/2 T, and at 4 K in self field an extrapolated Jc of at least 2×10 5 A/cm 2. Batch-processed PIT MgB 2/Fe strands and tapes were made at the University of Wollongong’s Institute for Superconducting and Electronic Materials. These were the focus of magnetization- and magnetic-shielding studies. Depending on the thickness of the Fe sheath, the superconducting core could be completely shielded at low fields (e.g. below 2 kOe). Taking this into account, the magnetic Jc is extracted, and found to be comparable to the extrapolated transport value.

  12. Image processing of correlated data by experimental design techniques

    SciTech Connect

    Stern, D.

    1987-01-01

    New classes of algorithms are developed for processing of two-dimensional image data imbedded in correlated noise. The algorithms are based on modifications of standard analysis of variance (ANOVA) techniques ensuring their proper operation in dependent noise. The approach taken in the development of procedures is deductive. First, the theory of modified ANOVA (MANOVA) techniques involving one- and two-way layouts are considered for noise models with autocorrelation matrix (ACM) formed by direct multiplication of rows and columns or tensored correlation matrices (TCM) stressing the special case of the first-order Markov process. Next, the techniques are generalized to include arbitrary, wide-sense stationary (WSS) processes. This permits dealing with diagonal masks which have ACM of a general form even for TCM. As further extension, the theory of Latin square (LS) masks is generalized to include dependent noise with TCM. This permits dealing with three different effects of m levels using only m{sup 2} observations rather than m{sup 3}. Since in many image-processing problems, replication of data is possible, the masking techniques are generalized to replicated data for which the replication is TCM dependent. For all procedures developed, algorithms are implemented which ensure real-time processing of images.

  13. Mapping the Asthma Care Process: Implications for Research and Practice.

    PubMed

    Dima, Alexandra Lelia; de Bruin, Marijn; Van Ganse, Eric

    2016-01-01

    Whether people with asthma gain and maintain control over their condition depends not only on the availability of effective drugs, but also on multiple patient and health care professional (HCP) behaviors. Research in asthma rarely considers how these behaviors interact with each other and drug effectiveness to determine health outcomes, which may limit real-life applicability of findings. The objective of this study was to develop a logic process model (Asthma Care Model; ACM) that explains how patient and HCP behaviors impact on the asthma care process. Within a European research project on asthma (ASTRO-LAB), we reviewed asthma care guidelines and empirical literature, and conducted qualitative interviews with patients and HCPs. Findings were discussed with the project team and respiratory care experts and integrated in a causal model. The model outlines a causal sequence of treatment events, from diagnosis and assessment to treatment prescription, drug exposure, and health outcomes. The relationships between these components are moderated by patient behaviors (medication adherence, symptom monitoring, managing triggers, and exacerbations) and HCP behaviors (medical care and self-management support). Modifiable and nonmodifiable behavioral determinants influence the behaviors of patients and HCPs. The model is dynamic as it includes feedback loops of behavioral and clinical outcomes, which influence future patient and HCP decision making. Key evidence for each relationship is summarized to derive research priorities and clinical recommendations. The ACM model is of interest to both researchers and practitioners, and intended as a first version (ACM-v1) of a common framework for generating and translating research evidence in asthma care. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

  14. Isothermal melt processing of Bi-2212 thick films

    NASA Astrophysics Data System (ADS)

    Holesinger, T. G.; Phillips, D. S.; Coulter, J. Y.; Willis, J. O.; Peterson, D. E.

    1995-02-01

    An alternative melt-processing technique has been developed for the fabrication of Bi 2Sr 2CaCu 2O y (Bi-2212) thick films at temperatures over 100°C lower than those employed in conventional Bi-2212 melt processing. Isothermal melt processing combines the melting and solidification steps at the same temperature [T.G. Holesinger et al., Appl. Phys. Lett. 63 (1993) 982]. This technique is possible due to the large drop in the solidus temperature with decreasing oxygen partial pressure. High-quality thick films were processed at temperatures as low as 770°C. Such films were found to be well-textured, contain relatively few secondary phases, and possess critical current densities over 1 × 10 5 A/cm 2 at 4 K in self-field.

  15. Isothermal melt processing of Bi 2Sr 2CaCu 2O y round wire

    NASA Astrophysics Data System (ADS)

    Holesinger, T. G.; Johnson, J. M.; Coulter, J. Y.; Safar, H.; Phillips, D. S.; Bingert, J. F.; Bingham, B. L.; Maley, M. P.; Smith, J. L.; Peterson, D. E.

    1995-02-01

    Isothermal melt processing (IMP) has been used to process oxide-powder-in-tube (OPIT) Bi 2Sr 2CaCu 2O y (Bi-2212) round wire with high critical current densities. Isothermal melt processing is a process in which the melting and solidification steps are carried out at the same temperature by melting in an inert atmosphere and solidifying in a high oxygen partial pressure. For each particular oxidizing atmosphere used during IMP, the highest critical currents were found in wires processed in the temperature range between 790°C to 820°C. The highest critical current densities obtained in 1.0, 0.75, and 0.5 mm diameter wires at 4 K and self-field were 4.3 × 10 4, 6.0 × 10 4, and 6.0 × 10 4 A/cm 2, respectively. Transport measurements on a 0.75 mm wire revealed that critical current densities in excess of 3 × 10 4 A/cm 2 could be achieved at 4 K in applied magnetic fields of 9 T. Anisotropy measurements and SEM analysis were used to examine the radial alignment of the Bi-2212 grain colonies within the wires.

  16. 75 FR 18536 - Agency Information Collection Activities: Proposed Collection, Comment Request

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-12

    ... ] Management Audit and Compliance Management (ACM) and Financial Management (FM) processes, and to assure that..., transportation contracts, and service contracts, supporting our ACM responsibilities under Federal and...

  17. Nb3Sn(Ti) powder metallurgy processed high field superconductors

    NASA Astrophysics Data System (ADS)

    Pourrahimi, S.; Thieme, C. L. H.; Foner, S.; Suenaga, M.

    1986-06-01

    Powder metallurgy processed Nb3Sn(Ti) superconducting wires were fabricated with Sn x wt. % Ti cores for 0≤x≤3, 16 or 22 vol % cores, and a Cu 45 wt. % Nb composite. The processing used swaging, cold hydrostatic extrusions, wire drawing and heat treatments of 750 °C for two to four days. Nominal areal reductions of 104 were used. Hydride-dehydride Nb and rotating electrode processed Nb powders gave the same performance. Overall critical current densities Jc were measured between 4.2 and 1.8 K for applied fields up to 23 T. Jc increased with increased Ti and/or Sn content. The Nb3Sn(Ti) wires using a Sn 3 wt. % Ti, 22 vol % core gave Jc >104 A/cm2 at 20 T and 4.2 K and Jc =104 A/cm2 at 23 T at 1.8 K. Removal of the precompression of the matrix increased Jc by about a factor of 2 at 20 T and 4.2 K.

  18. Process parameters, orientation, and functional properties of melt-processed bulk Y-Ba-Cu-O superconductors

    NASA Astrophysics Data System (ADS)

    Zakharchenko, I. V.; Terryll, K. M.; Rao, K. V.; Balachandran, U.

    1995-12-01

    This study compared the microstructure, texturing, and functional properties (critical currents) of YBa2Cu3O7-x-based bulk pellets that were prepared by the quench-melt-growth-process (QMGP), melt-textured growth, and conventional solid-state reaction approaches. Using two x-ray diffraction methods, θ-2θ, and rocking curves, we found that the individual grains of two melt-processed pellets exhibited remarkable preferred orientational alignment (best rocking curve width < 3.2‡). However, the direction of the preferred orientation among the grains was random. Among the three types of bulk materials studied, the QMGP sample was found to have the best Jc values, ≈4500 A/cm2 at 77K in a field of 2 kG, as determined from superconducting quantum interference device magnetic data.

  19. Study of the Deburring Process for Low Carbon Steel by Plasma Electrolytic Oxidation

    NASA Astrophysics Data System (ADS)

    Li, Hongtao; Kan, Jinfeng; Jiang, Bailing; Liu, Yanjie; Liu, Zheng

    2016-08-01

    In an appropriate electrochemical environment, the discrete thermal electron emission could be induced in the micro area due to the uneven distribution of electron flux on the anode surface. Thus an oxygen molecule could be ionized at the liquid-solid interface after collision, and then oxygen plasma with distribution characteristics would be formed. The plasma electrolytic oxidation (PEO) could happen at the liquid-solid interface. In this work, the low carbon steel was used to study the deburring process by PEO at a high frequency (70000 Hz) pulse DC mode. Its burr height H from 3.23 mm to 0.04 mm was removed to form a smooth surface within 6 min. The values of corrosion potential and current density for the untreated sample were -0.667 V and 6.735×10-5 A/cm2, respectively. But for the treated sample, the corrosion potential and current density were relatively lower, -0.354 V and 1.19×10-7 A/cm2. Therefore, PEO was expected to be a new deburring method of carbon steel for the material processing field. supported by National Natural Science Foundation of China (No. 51571114) and Natural Science Foundation of Jiangsu Province, China (No. BK20130935)

  20. Phase progression and phase relations related to processing Bi-based 2212 superconducting thick films

    NASA Astrophysics Data System (ADS)

    Zhang, Wei; Pashitski, Alex; Hellstrom, Eric E.

    1992-02-01

    Bi2Sr2CaCu2Ox(2212) films have been made by the doctor-blade technique and melt processed on Ag and Au foil. Two sets of organics have been used to prepare doctor-blade films. The doctor-blade films were put on the Ag and Au foil and heated at maximum temperatures of 885-890°C for Ag and 900-910°C for Au. With one set of organics a Sr-rich phase formed during melt processing that was mainly on the surface of the film. The 2212 grains nucleated directly from the liquid and grew preferentially along the free surface, but not at the oxide/substrate interface. Well-aligned 2212 grains were observed in thin 2212 films (<25 μm) on Ag and Au. The Jc at 4.2 K, 0T was 1.38×105 A/cm2 for the 2212/Ag film and 2.85×104 A/cm2 for the 2212/Au film.

  1. Electrochemical processing of nitrate waste solutions

    SciTech Connect

    Not Available

    1990-10-12

    Nitrate and nitrite have been almost completely removed from the synthetic effluent steam with good efficiency by affecting a separation across a pair of ion exchange membranes. In addition to recovering acid and base in this process, the volume of the remaining effluent is reduced considerably by transport of water across the membrane. One of the problems that remains with this process, however, is the stability of the membranes and particularly the stability of the anion exchange membrane. This membrane is exposed to both nitric acid and strongly alkaline solutions in the cell and to date long term stability has been a problem with the membranes tested. It is recommended that further work should evaluate other newly available membranes as well as study the effects of radiation on the performance of the membranes. The direct reduction of nitrate and nitrite has been studied at several different electrode materials and it has been demonstrated that cathode material has a large effect on both the efficiency and the gas product distribution. Highest current efficiencies for the reduction process are seen at those electrode materials that are known to show high hydrogen overpotentials. Flow cell studies have demonstrated that temperature and current density are also important parameters in the system. The reduction process has been run efficiently at high current densities (600 mAcm{sup {minus}2}) at 80{degrees}C at a lead cathode.

  2. U.S. Department of Energy, National Energy Technology Laboratory Solid-State Lighting Core Technologies Light Emitting Diodes on Semipolar Bulk GaN Substrate with IQE > 80% at 150 A/cm2 and 100 0C

    SciTech Connect

    Chakraborty, Arpan; David, Aurelien; Grundmann, Michael; Tyagi, Anurag; Craven, Michael; Hurni, Christophe; Cich, Michael

    2015-03-31

    GaN is a crucial material for light-emitting diodes (LEDs) emitting in the violet-to-green range. Despite its good performance, it still suffers from significant technical limitations. In particular, the efficiency of GaN-based LEDs decreases at high current (“current droop”) and high temperature (“temperature droop”). This is problematic in some lighting applications, where a high-power operation is required. This program studied the use of particular substrates to improve the efficiency of GaN-based LEDs: bulk semipolar (SP) GaN substrates. These substrates possess a very high material quality, and physical properties which are distinctly different from legacy substrates currently used in the LED industry. The program focused on the development of accurate metrology to quantify the performance of GaN-based LEDs, and on improvement to LED quality and design on SP substrates. Through a thorough optimization process, we demonstrated violet LEDs with very high internal quantum efficiency, exceeding 85% at high temperature and high current. We also investigated longer-wavelength blue emitters, but found that the limited strain budget was a key limitation.

  3. Methane assisted solid oxide co-electrolysis process for syngas production

    NASA Astrophysics Data System (ADS)

    Wang, Yao; Liu, Tong; Lei, Libin; Chen, Fanglin

    2017-03-01

    In this study, methane assisted high temperature steam/CO2 co-electrolysis process is performed on symmetrical cells with a configuration of SFM-SDC/LSGM/SFM-SDC to produce high-quality synthesis gas (syngas, a mixture of H2 and CO). The Nernst potential has been evaluated for solid oxide cells in the methane assisted mode, which is reduced by nearly one order of magnitude through substituting the anode atmosphere from air to methane. The open circuit voltage (OCV) is -0.06 V at 800 °C, and an electrolysis current density of -242 mAcm-2 has been obtained at 850 °C and 0.3 V. Effects of operating conditions on products composition have been revealed by using the chemical equilibrium co-electrolysis model and HSC software. High-quality syngas with high conversion rate of CO2 to CO as well as ideal H2/CO molar ratio of 2 could be achieved in both electrode sides by adjusting appropriate operating conditions. The short-term cell voltage is slightly fluctuant less than 0.05 V at 850 °C and -120 mAcm-2, in which condition carbon deposition has been observed in the SFM-SDC anode due to the low O2-/CH4 ratio.

  4. Prediction of Temperatures of Austenite Equilibrium Transformations in Steels During Thermomechanical Processing

    NASA Astrophysics Data System (ADS)

    Samadian, Pedram; Parsa, Mohammad Habibi; Ahmadabadi, M. Nili; Mirzadeh, Hamed

    2014-10-01

    Knowledge about the transformation temperatures is crucial in processing of steels especially in thermomechanical processes because microstructures and mechanical properties after processing are closely related to the extent and type of transformations. The experimental determination of critical temperatures is costly, and therefore, it is preferred to predict them by mathematical methods. In the current work, new thermodynamically based models were developed for computing the Ae3 and Acm temperatures in the equilibrium cooling conditions when austenite is deformed at elevated temperatures. The main advantage of the proposed models is their capability to predict the temperatures of austenite equilibrium transformations in steels with total alloying elements (Mn + Si + Ni + Cr + Mo + Cu) less than 5 wt.% and Si less than 1 wt.% under the deformation conditions just by using the chemical potential of constituents, without the need for determining the total Gibbs free energy of steel which requires many experiments and computations.

  5. A time- and temperature-dependent two-dimensional simulation of GTO turnoff process II—Inductive load case

    NASA Astrophysics Data System (ADS)

    Nakagawa, Akio

    1985-07-01

    Two-dimensional simulation was carried out for the GTO thyristor turnoff process under an inductive load with 34 A (3400 A/cm 2) initial anode current and 7.2 A gate current, which is the same condition as that in which a significant current concentration into a small part of a device area was experimentally observed. A 24,000 A/cm 2 maximum anode current density is reached during the turnoff process in the reduced "on-region" (see text for the definition). The on-region width in the p-base reduces rapidly to 70 μm and remains at around 60 μm until the device is completely turned off. It is shown that a large amount of the stored n-base carriers in the current concentrated area are removed by the developing high electric field region in the n-base. This results in a large d V/d t current, which sustains the high current density in the current concentrated area.

  6. Automated Construction Management System (ACMS). Volume 2. Program Documentation.

    DTIC Science & Technology

    1984-06-01

    fe -e !t !a’.*I - . I’ q . .% % .. -S C .. .. .. .. .. .. .. . .. . 19 BAC UP CM . . oo o .. .. s.. .. .. . o.. s .. .. . . . . 197 WP . M s . . . . .s...USE RETURN * * *END BACKUP.CMD 26**. *% A C M S Ver. 84.0 ’ * USA-CERL PROGRAM: BILL.CMD " * DESCRIPTION: This program allows the user to set up ...11,0 SAY "Schedules Included: " ?? " <Type CTR-Q to abort>" SELECT SECOND STORE 12 TO row STORE 0 TO col * up to 80 schedules can be displayed on

  7. Surgical management of an ACM aneurysm eight years after coiling.

    PubMed

    Pogády, P; Fellner, F; Trenkler, J; Wurm, G

    2007-04-01

    The authors present a case report on rebleeding of a medial cerebral aneurysm (MCA) eight years after complete endovascular coiling. The primarily successfully coiled MCA aneurysm showed a local regrowth which, however, was not the source of the rebleeding. The angiogram demonstrated no evidence of contrast filling of the coiled segment, but according to intraoperative findings (haematoma location, displacement of coils, evident place of rupture) there is no doubt that the coiled segment of the aneurysm was responsible for the haemorrhage.

  8. Migraine with aura, bipolar depression, ACM aneurysm. A case report.

    PubMed

    de Filippis, Sergio; Salvatori, Emiliano; Bozzao, Alessandro; Fantozzi, Luigi Maria; Martelletti, Paolo

    2005-04-01

    B.D. is a 48-year-old professional woman. She has been suffering for migraine since she was 28, but she did not have serious problems until last year, when headache episodes became more frequent and it was necessary an admission to emergency room. At the beginning, the events were about 6 per month, lasting from 2 to 4 days, beating and of high intensity together with nausea, vomit, photo and phonophobia and visual area. Looking at the anamnesis, we report a psychiatric treatment since about ten years, because of type II bipolar disorder. In spite of the psychopharmacological treatment, as the patient came in our Regional Headache Center, she talked about 7 events with aura (scintillating scotomas, emianopsia) per month, lasting 2-4 days with photo and phonophobia, nausea, crying crisis, anxiety. Although the neurological examination was normal, the sudden aggravation of pain symptomatology and the unresposiveness to usual painkillers, suggested a cerebral CT and CT-angiography. CT and CT-angiography discovered the presence of an aneurysm of the right middle cerebral artery (MCA) of 4 mm diameter, with parietal irregularities. The patient was operated to reduce the hemorrhagic risk, with a positive result. One year after the operation, the patient reports a decrease of headache events with a frequency of 2 per month, lasting only a few hours, which she can now solve with COXIB.

  9. US EPA, Pesticide Product Label, ACME GARDEN WEED ...

    EPA Pesticide Factsheets

    2011-04-21

    ... til jI~ "f (I \\ ~) I ~ , .. i'" I' C"IIII,il'! 1'(~I'(~"t sill I 1'1' () I- Il , h. I II I ,. I 'I \\;

  10. Multilingual Information Discovery and AccesS (MIDAS): A Joint ACM DL'99/ ACM SIGIR'99 Workshop.

    ERIC Educational Resources Information Center

    Oard, Douglas; Peters, Carol; Ruiz, Miguel; Frederking, Robert; Klavans, Judith; Sheridan, Paraic

    1999-01-01

    Discusses a multidisciplinary workshop that addressed issues concerning internationally distributed information networks. Highlights include multilingual information access in media other than character-coded text; cross-language information retrieval and multilingual metadata; and evaluation of multilingual systems. (LRW)

  11. Multilingual Information Discovery and AccesS (MIDAS): A Joint ACM DL'99/ ACM SIGIR'99 Workshop.

    ERIC Educational Resources Information Center

    Oard, Douglas; Peters, Carol; Ruiz, Miguel; Frederking, Robert; Klavans, Judith; Sheridan, Paraic

    1999-01-01

    Discusses a multidisciplinary workshop that addressed issues concerning internationally distributed information networks. Highlights include multilingual information access in media other than character-coded text; cross-language information retrieval and multilingual metadata; and evaluation of multilingual systems. (LRW)

  12. Evidence for anthropogenic impact on number concentration and sulfate content of cloud-processed aerosol particles over the North-Atlantic

    NASA Astrophysics Data System (ADS)

    van Dingenen, Rita; Raes, Frank; Jensen, Niels R.

    1995-10-01

    Aerosol properties were measured during two transects over the North Atlantic between Halifax (Nova Scotia, Canada) and the Moroccan coast. Measurements of the chemical composition of total aerosol, of the black carbon concentration and of the number size distributions with particle diameter Dp in the range 16 nm < Dp < 1 μm were made. The e-folding lifetime of the black carbon aerosol, coming from the northeast American continent and transported eastward over the ocean, was estimated to be 15 hours. The non-sea-salt (nss) fraction of the sulfate concentrations encountered during this campaign spans a 3 order of magnitude range (0.02 μm m-3 to 19 μm m-3) and shows a high correlation with black carbon. The measured bimodal aerosol size distributions were analysed in order to yield number concentrations of the nuclei and the accumulation mode (ACM), the latter being interpreted as cloud-processed particles and thus as cloud condensation nuclei (CCN). A strong positive correlation was found between ACM number concentration and nss-sulfate load over the whole concentration range, i.e. for clean to polluted air masses. Furthermore, our regression between nss-sulfate and ACM number concentration also agrees well with results from other investigators where CCN or cloud droplet concentrations were related to nss-sulfate at a variety of geographical locations and degrees of pollution. The composite data set shows that the nss-sulfate-CCN relationship from baseline conditions to anthropogenically conditioned aerosol, happens via a smooth transition which can be described by a linear regression on a logarithmic scale.

  13. Ultra-High Performance, High-Temperature Superconducting Wires via Cost-effective, Scalable, Co-evaporation Process

    SciTech Connect

    Kim, Dr. Hosup; Oh, Sang-Soo; Ha, HS; Youm, D; Moon, SH; Kim, JH; Heo, YU; Dou, SX; Wee, Sung Hun; Goyal, Amit

    2014-01-01

    Long-length, high-temperature superconducting (HTS) wires capable of carrying high critical current, Ic, are required for a wide range of applications. Here, we report extremely high performance HTS wires based on 5 m thick SmBa2Cu3O7- (SmBCO) single layer films on textured metallic templates. SmBCO layer wires over 20 meters long were deposited by a cost-effective, scalable co-evaporation process using a batch-type drum in a dual chamber. All deposition parameters influencing the composition, phase, and texture of the films were optimized via a unique combinatorial method that is broadly applicable for co-evaporation of other promising complex materials containing several cations. Thick SmBCO layers deposited under optimized conditions exhibit excellent cube-on-cube epitaxy. Such excellent structural epitaxy over the entire thickness results in exceptionally high Ic performance, with average Ic over 1000 A/cm for the entire 22 meter long wire and maximum Ic over 1,500 A/cm for a short 12 cm long tape. The Ic values reported in this work are the highest values ever reported from any lengths of cuprate-based HTS wire or conductor.

  14. Seeking inclusion in an exclusive process: discourses of medical school student selection.

    PubMed

    Razack, Saleem; Hodges, Brian; Steinert, Yvonne; Maguire, Mary

    2015-01-01

    Calls to increase medical class representativeness to better reflect the diversity of society represent a growing international trend. There is an inherent tension between these calls and competitive student selection processes driven by academic achievement. How is this tension manifested? Our three-phase interdisciplinary research programme focused on the discourses of excellence, equity and diversity in the medical school selection process, as conveyed by key stakeholders: (i) institutions and regulatory bodies (the websites of 17 medical schools and 15 policy documents from national regulatory bodies); (ii) admissions committee members (ACMs) (according to semi-structured interviews [n = 9]), and (iii) successful applicants (according to semi-structured interviews [n = 14]). The work is theoretically situated within the works of Foucault, Bourdieu and Bakhtin. The conceptual framework is supplemented by critical hermeneutics and the performance theories of Goffman. Academic excellence discourses consistently predominate over discourses calling for greater representativeness in medical classes. Policy addressing demographic representativeness in medicine may unwittingly contribute to the reproduction of historical patterns of exclusion of under-represented groups. In ACM selection practices, another discursive tension is exposed as the inherent privilege in the process is marked, challenging the ideal of medicine as a meritocracy. Applicants' representations of self in the 'performance' of interviewing demonstrate implicit recognition of the power inherent in the act of selection and are manifested in the use of explicit strategies to 'fit in'. How can this critical discourse analysis inform improved inclusiveness in student selection? Policymakers addressing diversity and equity issues in medical school admissions should explicitly recognise the power dynamics at play between the profession and marginalised groups. For greater inclusion and to avoid one

  15. Effects of Known Determinants on Methylene Bisphenyl Isocyanate (MDI) Concentration During Spray-On Truck Bed-Lining Processes.

    PubMed

    Schaal, Nicholas C; Brazile, William J; Finnie, Katie L; Tiger, James P

    2017-08-01

    Occupational exposure to methylene bisphenyl isocyanate (MDI) presents serious worker health concerns as it may lead to short- and long-term health effects such as asthma, airway irritation, hypersensitivity pneumonitis, and irritation of skin and mucous membranes. While studies of worker isocyanate exposures during vehicle painting activities are widespread, few studies have investigated the spray-on truck bed-liner (STBL) industry. The purpose of this study was to determine the effectiveness of several ventilation system variables and process characteristics in controlling MDI concentrations in the STBL industry. A total of 47 personal air samples were collected for MDI during 18 site visits at nine STBL companies in Colorado and Wyoming. Ventilation system and process characteristics that were assessed included: ventilation system face velocity, airflow, air changes per minute (AC/M), capture velocity, percent of MDI in bed-liner product, application temperature, application pressure, paint booth temperature, paint booth relative humidity, paint booth volume, and quantity of bed-liner product applied. Pearson correlation revealed percentage of MDI in bed-liner product (r = 0.557, n = 14, P < 0.05) and process temperature (r = 0.677, n = 14, P < 0.05) had high positive correlation with MDI concentration. Ventilation system face velocity (r = -0.578, n = 14, P < 0.05) and AC/M (r = -0.657, n = 14, P < 0.05) had high negative correlation with MDI concentration while airflow (r = -0.475, n = 14, P < 0.05) and capture velocity (r = -0.415, n = 14, P = 0.07) had moderate negative correlation with MDI concentration. Multiple linear regression revealed process temperature and capture velocity made a statistically significant and unique contribution in estimating MDI concentration (F (2, 11) = 10.99, P < 0.05) with an adjusted R2 of 0.61, explaining 61% of the variability in MDI concentration. This investigation contributed to an understudied STBL industry by targeting

  16. Superconducting Performance, Microstructure and SEM by EDX Analysis of IG Processed YBa2Cu3Oy Bulk Superconductors by Top and Interior Seeding Methods

    NASA Astrophysics Data System (ADS)

    Ide, N.; Muralidhar, M.; Radusovska, M.; Diko, P.; Jirsa, M.; Murakami, M.

    2017-07-01

    The top-seeded and interior seeded methods, together with infiltration growth (IG) technique were used to produce YBa2Cu3Oy (Y-123) samples with Y2BaCuO5 (Y-211) secondary phase particles. Tc (onset) was around 91.5. K. When interior seeding process was used, a complete growth of Y-123 single grain starting at the lower part of the bulk was observed by optical microscopy. The Y-211 particles dispersion was quite uniform in lower and upper parts of the samples, both in the a- and c-axis growth sectors, both at the beginning and end of the grain growth. In the sample produced by infiltration growth and interior seeding the critical current density at 77 K with H//c-axis was 44,000 A/cm2 and 7,750 A/cm2 in self-field and 2 T, respectively. It is a good basis for optimization of processing conditions, which can further improve the superconductor’s performance and enable to grow large-size Y-123 bulks.

  17. Electrochemical processing of nitrate waste solutions. Final Report

    SciTech Connect

    Not Available

    1990-10-12

    Nitrate and nitrite have been almost completely removed from the synthetic effluent steam with good efficiency by affecting a separation across a pair of ion exchange membranes. In addition to recovering acid and base in this process, the volume of the remaining effluent is reduced considerably by transport of water across the membrane. One of the problems that remains with this process, however, is the stability of the membranes and particularly the stability of the anion exchange membrane. This membrane is exposed to both nitric acid and strongly alkaline solutions in the cell and to date long term stability has been a problem with the membranes tested. It is recommended that further work should evaluate other newly available membranes as well as study the effects of radiation on the performance of the membranes. The direct reduction of nitrate and nitrite has been studied at several different electrode materials and it has been demonstrated that cathode material has a large effect on both the efficiency and the gas product distribution. Highest current efficiencies for the reduction process are seen at those electrode materials that are known to show high hydrogen overpotentials. Flow cell studies have demonstrated that temperature and current density are also important parameters in the system. The reduction process has been run efficiently at high current densities (600 mAcm{sup {minus}2}) at 80{degrees}C at a lead cathode.

  18. Object-Oriented Parallel Processing with Mentat

    DTIC Science & Technology

    2001-01-01

    ogy, 1993. 10 R. Chin and S. Chanson , “Distributed Object-Based Programming Systems,” ACM Computing Surveys, pp. 91-127, vol. 23, no. 1, March., 1991...SCCS 42c, NPAC, Syracuse Uni- versity, Syracuse, NY. 15 A. S. Grimshaw, W. A. Wulf, J. C. French , A.C. Weaver, and Paul Reynolds Jr. “Legion: The Next

  19. Recycling and processing of several typical crosslinked polymer scraps with enhanced mechanical properties based on solid-state mechanochemical milling

    NASA Astrophysics Data System (ADS)

    Lu, Canhui; Zhang, Xinxing; Zhang, Wei

    2015-05-01

    The partially devulcanization or de-crosslinking of ground tire rubber (GTR), post-vulcanized fluororubber scraps and crosslinked polyethylene from cable scraps through high-shear mechanochemical milling (HSMM) was conducted by a modified solid-state mechanochemical reactor. The results indicated that the HSMM treated crosslinked polymer scraps can be reprocessed as virgin rubbers or thermoplastics to produce materials with high performance. The foamed composites of low density polyethylene/GTR and the blend of post-vulcanized flurorubber (FKM) with polyacrylate rubber (ACM) with better processability and mechanical properties were obtained. The morphology observation showed that the dispersion and compatibility between de-crosslinked polymer scraps and matrix were enhanced. The results demonstrated that HSMM is a feasible alternative technology for recycling post-vulcanized or crosslinked polymer scraps.

  20. Annealing Dependence of Solution-Processed Ultra-Thin ZrOx Films for Gate Dielectric Applications.

    PubMed

    Liu, G X; Liu, A; Meng, Y; Shan, F K; Shin, B C; Lee, W J; Cho, C R

    2015-03-01

    Ultra-thin ZrOx thin films on Si substrates were prepared by sol-gel technique and processed with different methods (baked on hot plate at 150 °C, annealed at 500 °C in furnace, and photo-annealed under UV light). The decomposition of the organic groups and the formation of Zr-O bonding in the ZrOx thin films were confirmed by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. It is found that the ZrOx thin film annealed under UV light shows decent characteristics, including an ultra-small surface roughness, a low leakage current density of 10(-9) A/cm2 at 1 MV/cm, a large breakdown electric field of 9.5 MV/cm, and a large areal capacitance of 775 nF/cm2.

  1. Recycling and processing of several typical crosslinked polymer scraps with enhanced mechanical properties based on solid-state mechanochemical milling

    SciTech Connect

    Lu, Canhui; Zhang, Xinxing; Zhang, Wei

    2015-05-22

    The partially devulcanization or de-crosslinking of ground tire rubber (GTR), post-vulcanized fluororubber scraps and crosslinked polyethylene from cable scraps through high-shear mechanochemical milling (HSMM) was conducted by a modified solid-state mechanochemical reactor. The results indicated that the HSMM treated crosslinked polymer scraps can be reprocessed as virgin rubbers or thermoplastics to produce materials with high performance. The foamed composites of low density polyethylene/GTR and the blend of post-vulcanized flurorubber (FKM) with polyacrylate rubber (ACM) with better processability and mechanical properties were obtained. The morphology observation showed that the dispersion and compatibility between de-crosslinked polymer scraps and matrix were enhanced. The results demonstrated that HSMM is a feasible alternative technology for recycling post-vulcanized or crosslinked polymer scraps.

  2. Levitation-force measurements and field mapping of melt-processed YBa 2Cu 3O 7- x ceramics

    NASA Astrophysics Data System (ADS)

    Lehndorff, Beate; Kürschner, Hans-Gerd; Lücke, Bernhard; Piel, Helmut

    1995-02-01

    YBa 2Cu 3O 7- x ceramics were produced by a melt-textured growth (MTG) process. They consist of large grains of 2-5 mm diameter with micron-sized Y-211 inclusions as analyzed by optical and electron microscopy (SEM/EDX). Their JC was determined by an inductive method to be in the range of 2000 A/cm 2. A 3D positioning system was built to measure the levitation force of a permanent magnet above these ceramic superconductors as a function of distance and the relative position on the sample surface using force sensors. The magnetic stiffness was compared for sintered and MTG samples. The latter shows a much stronger dependence of the stiffness on the magnetic field. In addition the trapped-flux distribution mapped by means of a Hall sensor reveals clearly the grain structure of the MTG sample.

  3. Critical current densities of superconducting YBa 2Cu 4O 8 synthesised by the citrate gel process

    NASA Astrophysics Data System (ADS)

    Liu, R. S.; Zheng, D. N.; Janes, R.; Campbell, A. M.; Edwards, P. P.

    1990-12-01

    High-T c superconducting YBa 2Cu 4O 8 submicron powders with transition temperature around 80 K were successfully synthesized via citrate gel process at one atmosphere oxygen pressure. An intragrain critical current density of up to 1.3×10 7A/ cm2 at 6 K and H=1 T has been measured by magnetisation method; this value is comparable to that found in sintered YBa 2Cu 3O 7-δ. The integrain criticalcurrent density, as measured by an a.c. inductive technique, was 10 3 A/cm 2 at 4.2 K; this is in excess of typical values for YBa 2Cu 3O 7-δ.

  4. New ceramic coating technique using laser spraying process

    NASA Astrophysics Data System (ADS)

    Tsukamoto, Koichi; Yanagisawa, Takeshi; Uchiyama, Futodhi; Obara, Akira; Okutomi, Mamoru; Kimura, Shinji; Yamada, Akimasa; Shen, Hong L.; Wang, Zhongcheng; Shen, Qinwo; Chatterjee, Udit; Bhar, Gopal C.

    1998-08-01

    A new ceramic coating technique using a CO2 laser has been developed. A high power density laser beam passes near the substrate. Coating materials are supplied by an extra-high accuracy powder supply device and pass across the laser beam. The coating materials are melted in the laser beam and deposited on the substrate surface. A YSZ (Yttria Stabilized Zirconia) layer and a LaCoO3 layer are made for high temperature solid oxide fuel cells. The crystal structures of the coated layers are the same as that of the original coating materials. Superconducting BPSCCO ceramic films are also made with this process. The films show super-conductivity with Tc at 81 K. The Jc of the specimen is 440 A/cm2 at 77 K. We can easily handle and arrange not only metal but also refractory materials. By adopting a multi-axis robot and a surface treatment laser technique, the laser spraying method described here makes it possible to produce highly functional and three dimensional parts of devices directly from raw powder materials. Thus the proposed method will open the path to an unexplored field of key production technology.

  5. Direct observation of Sn crystal growth during the lithiation and delithiation processes of SnO(2) nanowires.

    PubMed

    Zhang, Li Qiang; Liu, Xiao Hua; Perng, Ya-Chuan; Cho, Jea; Chang, Jane P; Mao, Scott X; Ye, Zhi Zhen; Huang, Jian Yu

    2012-11-01

    Tin (Sn) crystal growth on Sn-based anodes in lithium ion batteries is hazardous for reasons such as possible short-circuit failure by Sn whiskers and Sn-catalyzed electrolyte decomposition, but the growth mechanism of Sn crystals during battery cycling is not clear. Here we report different growth mechanisms of Sn crystal during the lithiation and delithiation processes of SnO(2) nanowires revealed by in situ transmission electron microscopy (TEM). Large spherical Sn nanoparticles with sizes of 20-200nm grew instantaneously upon lithiation of a single-crystalline SnO(2) nanowire at large current density (j>20A/cm(2)), which suppressed formation of the Li(x)Sn alloy but promoted agglomeration of Sn atoms. Control experiments of Joule-heating (j≈2400A/cm(2)) the pristine SnO(2) nanowires resulted in melting of the SnO(2) nanowires but not Sn particle growth, indicating that the abnormal Sn particle growth was induced by both chemical reduction (i.e., breaking the SnO(2) lattice to produce Sn atoms) and agglomeration of the Sn atoms assisted by Joule heating. Intriguingly, Sn crystals grew out of the nanowire surface via a different "squeeze-out" mechanism during delithiation of the lithiated SnO(2) nanowires coated with an ultra-thin solid electrolyte LiAlSiO(x) layer. It is attributed to the negative stress gradient generated by the fast Li extraction in the surface region through the Li(+)-conducting LiAlSiO(x) layer. Our previous studies showed that Sn precipitation does not occur in the carbon-coated SnO(2) nanowires, highlighting the effect of nanoengineering on tailoring the electrochemical reaction kinetics to suppress the hazardous Sn whiskers or nanoparticles formation in a lithium ion battery.

  6. Budgeting Process

    ERIC Educational Resources Information Center

    Hentschke, Guilbert C.; Shaughnessy, John

    1973-01-01

    Attempts to describe the budgeting process in school districts. Discusses general budget calendars and explains the process of constructing a Program Evaluation and Review Technique (PERT) chart of the budgeting process. Presents a detailed list of activities to be included in the budgeting process and a PERT chart indicating how these activities…

  7. Meat Processing.

    ERIC Educational Resources Information Center

    Legacy, Jim; And Others

    This publication provides an introduction to meat processing for adult students in vocational and technical education programs. Organized in four chapters, the booklet provides a brief overview of the meat processing industry and the techniques of meat processing and butchering. The first chapter introduces the meat processing industry and…

  8. Algorithm Design for Computational Fluid Dynamics, Scientific Visualization, and Image Processing

    DTIC Science & Technology

    2007-01-29

    ACM TOG 22, 871-878 (2003). "• [1TF] Irving, G., Teran , J. and Fedkiw, R., "Invertible Finite Elements for Robust Simulation of Large Deformation" ACM...34• [MBTF] Molino, N., Bridson, R., Teran , J. and Fedkiw, R., "A Crystalline, Red Green Strategy for Meshing Highly Deformable Objects with Tetrahedra...34, 12th Int. Meshing Roundtable, 103-114, 2003. "* [BTMF] Bridson, R., Teran , J., Molino, N. and Fedkiw, R., "Adaptive Physics Based Tetrahedral Mesh

  9. High Electron Mobility Ge n-Channel Metal-Insulator-Semiconductor Field-Effect Transistors Fabricated by the Gate-Last Process with the Solid Source Diffusion Technique

    NASA Astrophysics Data System (ADS)

    Maeda, Tatsuro; Morita, Yukinori; Takagi, Shinichi

    2010-06-01

    We fabricate high-k/Ge n-channel metal-insulator-semiconductor field-effect transistors (MISFETs) by the gate-last process with the thermal solid source diffusion to achieve both of high quality source/drain (S/D) and gate stack. The n+/p junction formed by solid source diffusion technique of Sb dopant shows the excellent diode characteristics of ˜1.5×105 on/off ratio between +1 and -1 V and the quite low reverse current density of ˜4.1×10-4 A/cm2 at +1 V after the fabrication of high-k/Ge n-channel MISFETs that enable us to observe well-behaved transistor performances. The extracted electron mobility with the peak of 891 cm2/(V.s) is high enough to be superior to the Si universal electron mobility especially in low Eeff.

  10. Artificial Immune System for Flight Envelope Estimation and Protection

    DTIC Science & Technology

    2014-12-31

    Figure 1.7. AIS-Based ACM Process 31 Figure 1.8. AIS-Based ACM System Design 32 Figure 1.9. On-Line AC Detection... ACM ) based on the AIS paradigm can be considered to include three main components functionally connected in a closed loop as shown in Figure 1.7...off-line ACM system design and implementation  on-line AC detection, identification, evaluation, and accommodation  post-processing of flight data

  11. Science Processes.

    ERIC Educational Resources Information Center

    Finley, Fred N.

    1983-01-01

    Reports an investigation of the epistomologic foundations of Gagne's conception of science processes. Results indicate that a commitment to inductive empiricism pervades the presently held view of science processes. Implications for science education are considered. (Author/JN)

  12. Mapping Signal Processing Kernels to Tiled Architectures

    DTIC Science & Technology

    2007-11-02

    attractive alternatives to monolithic computer architecture designs because they allow a larger design to be built from smaller modules and limit the...Computer Architectures. ACM Transactions on Computer Systems, 2(4):289–308, November 1984. [12] Steven Swanson, Ken Michelson , Andrew Schwerin, and...Program MIT Lincoln LaboratoryHPEC 2004-3 JML 28 Sep 2004 Tiled Architectures • Monolithic single-chip architectures are becoming rare in the industry

  13. Prediction of Proper Temperatures for the Hot Stamping Process Based on the Kinetics Models

    NASA Astrophysics Data System (ADS)

    Samadian, P.; Parsa, M. H.; Mirzadeh, H.

    2015-02-01

    Nowadays, the application of kinetics models for predicting microstructures of steels subjected to thermo-mechanical treatments has increased to minimize direct experimentation, which is costly and time consuming. In the current work, the final microstructures of AISI 4140 steel sheets after the hot stamping process were predicted using the Kirkaldy and Li kinetics models combined with new thermodynamically based models in order for the determination of the appropriate process temperatures. In this way, the effect of deformation during hot stamping on the Ae3, Acm, and Ae1 temperatures was considered, and then the equilibrium volume fractions of phases at different temperatures were calculated. Moreover, the ferrite transformation rate equations of the Kirkaldy and Li models were modified by a term proposed by Åkerström to consider the influence of plastic deformation. Results showed that the modified Kirkaldy model is satisfactory for the determination of appropriate austenitization temperatures for the hot stamping process of AISI 4140 steel sheets because of agreeable microstructure predictions in comparison with the experimental observations.

  14. Solution-Processed Dielectrics Based on Thickness-Sorted Two-Dimensional Hexagonal Boron Nitride Nanosheets

    SciTech Connect

    Zhu, Jian; Kang, Joohoon; Kang, Junmo; Jariwala, Deep; Wood, Joshua D.; Seo, Jung-Woo T.; Chen, Kan-Sheng; Marks, Tobin J.; Hersam, Mark C.

    2015-10-14

    Gate dielectrics directly affect the mobility, hysteresis, power consumption, and other critical device metrics in high-performance nanoelectronics. With atomically flat and dangling bond-free surfaces, hexagonal boron nitride (h-BN) has emerged as an ideal dielectric for graphene and related two-dimensional semiconductors. While high-quality, atomically thin h-BN has been realized via micromechanical cleavage and chemical vapor deposition, existing liquid exfoliation methods lack sufficient control over h-BN thickness and large-area film quality, thus limiting its use in solution-processed electronics. Here, we employ isopycnic density gradient ultracentrifugation for the preparation of monodisperse, thickness-sorted h-BN inks, which are subsequently layer-by-layer assembled into ultrathin dielectrics with low leakage currents of 3 × 10–9 A/cm2 at 2 MV/cm and high capacitances of 245 nF/cm2. The resulting solution-processed h-BN dielectric films enable the fabrication of graphene field-effect transistors with negligible hysteresis and high mobilities up to 7100 cm2 V–1 s–1 at room temperature. These h-BN inks can also be used as coatings on conventional dielectrics to minimize the effects of underlying traps, resulting in improvements in overall device performance. Overall, this approach for producing and assembling h-BN dielectric inks holds significant promise for translating the superlative performance of two-dimensional heterostructure devices to large-area, solution-processed nanoelectronics.

  15. Solution-Processed Dielectrics Based on Thickness-Sorted Two-Dimensional Hexagonal Boron Nitride Nanosheets.

    PubMed

    Zhu, Jian; Kang, Joohoon; Kang, Junmo; Jariwala, Deep; Wood, Joshua D; Seo, Jung-Woo T; Chen, Kan-Sheng; Marks, Tobin J; Hersam, Mark C

    2015-10-14

    Gate dielectrics directly affect the mobility, hysteresis, power consumption, and other critical device metrics in high-performance nanoelectronics. With atomically flat and dangling bond-free surfaces, hexagonal boron nitride (h-BN) has emerged as an ideal dielectric for graphene and related two-dimensional semiconductors. While high-quality, atomically thin h-BN has been realized via micromechanical cleavage and chemical vapor deposition, existing liquid exfoliation methods lack sufficient control over h-BN thickness and large-area film quality, thus limiting its use in solution-processed electronics. Here, we employ isopycnic density gradient ultracentrifugation for the preparation of monodisperse, thickness-sorted h-BN inks, which are subsequently layer-by-layer assembled into ultrathin dielectrics with low leakage currents of 3 × 10(-9) A/cm(2) at 2 MV/cm and high capacitances of 245 nF/cm(2). The resulting solution-processed h-BN dielectric films enable the fabrication of graphene field-effect transistors with negligible hysteresis and high mobilities up to 7100 cm(2) V(-1) s(-1) at room temperature. These h-BN inks can also be used as coatings on conventional dielectrics to minimize the effects of underlying traps, resulting in improvements in overall device performance. Overall, this approach for producing and assembling h-BN dielectric inks holds significant promise for translating the superlative performance of two-dimensional heterostructure devices to large-area, solution-processed nanoelectronics.

  16. Shuttle Processing

    NASA Technical Reports Server (NTRS)

    Guodace, Kimberly A.

    2010-01-01

    This slide presentation details shuttle processing flow which starts with wheel stop and ends with launching. The flow is from landing the orbiter is rolled into the Orbiter Processing Facility (OPF), where processing is performed, it is then rolled over to the Vehicle Assembly Building (VAB) where it is mated with the propellant tanks, and payloads are installed. A different flow is detailed if the weather at Kennedy Space Center requires a landing at Dryden.

  17. ASCOT process

    SciTech Connect

    Bonilla, J.A.

    1985-12-01

    Foster Wheeler is developing the ASCOT (Asphalt Coking Technology) process which combines a modified solvent deasphalting (SDA) unit, using heavy solvents, with a delayed coking (DC) unit for the upgrade of heavy oils into intermediate products suitable for processing in conventional refinery units, to produce high quality distillate products. This paper presents a description of the ASCOT process and its application to the upgrade of San Joaquin vacuum residue. The ASCOT process is then compared to the independent applications of DC and SDA. 6 references.

  18. Peat Processing

    NASA Technical Reports Server (NTRS)

    1986-01-01

    Humics, Inc. already had patented their process for separating wet peat into components and processing it when they consulted NERAC regarding possible applications. The NERAC search revealed numerous uses for humic acid extracted from peat. The product improves seed germination, stimulates root development, and improves crop yields. There are also potential applications in sewage disposal and horticultural peat, etc.

  19. Improving predictions of large scale soil carbon dynamics: Integration of fine-scale hydrological and biogeochemical processes, scaling, and benchmarking

    NASA Astrophysics Data System (ADS)

    Riley, W. J.; Dwivedi, D.; Ghimire, B.; Hoffman, F. M.; Pau, G. S. H.; Randerson, J. T.; Shen, C.; Tang, J.; Zhu, Q.

    2015-12-01

    Numerical model representations of decadal- to centennial-scale soil-carbon dynamics are a dominant cause of uncertainty in climate change predictions. Recent attempts by some Earth System Model (ESM) teams to integrate previously unrepresented soil processes (e.g., explicit microbial processes, abiotic interactions with mineral surfaces, vertical transport), poor performance of many ESM land models against large-scale and experimental manipulation observations, and complexities associated with spatial heterogeneity highlight the nascent nature of our community's ability to accurately predict future soil carbon dynamics. I will present recent work from our group to develop a modeling framework to integrate pore-, column-, watershed-, and global-scale soil process representations into an ESM (ACME), and apply the International Land Model Benchmarking (ILAMB) package for evaluation. At the column scale and across a wide range of sites, observed depth-resolved carbon stocks and their 14C derived turnover times can be explained by a model with explicit representation of two microbial populations, a simple representation of mineralogy, and vertical transport. Integrating soil and plant dynamics requires a 'process-scaling' approach, since all aspects of the multi-nutrient system cannot be explicitly resolved at ESM scales. I will show that one approach, the Equilibrium Chemistry Approximation, improves predictions of forest nitrogen and phosphorus experimental manipulations and leads to very different global soil carbon predictions. Translating model representations from the site- to ESM-scale requires a spatial scaling approach that either explicitly resolves the relevant processes, or more practically, accounts for fine-resolution dynamics at coarser scales. To that end, I will present recent watershed-scale modeling work that applies reduced order model methods to accurately scale fine-resolution soil carbon dynamics to coarse-resolution simulations. Finally, we

  20. Impact of nanosecond proton beam processing on nanoblocks of copper

    NASA Astrophysics Data System (ADS)

    Borodin, Y. V.; Mantina, A. Y.; Pak, V.; Zhang, X. X.

    2017-01-01

    X-ray studies in conjunction with the method of recoil nuclei and electron microscopy of irradiated plates polycrystalline Cu by nanosecond high power density proton beams (E = 120 keV; I = 80 A/cm2, t = 50 ns) showed nano block nature of the formation of structure in the surface layer target and condensed-formed film.

  1. Process description

    NASA Technical Reports Server (NTRS)

    1975-01-01

    The production of hydrogen from coal by hydrogasification and subsequent steam hydrocarbon reforming was studied. Process heat and power requirements are supplied by an HTGR. The process is examined as a function of a maximum reforming (process) temperature of 922 K (1200 F) to 1367 K (2000 F). The major parameters for the five cases selected are summarized in a table. A fixed thermal capacity of 3000 MW for the HTGR heat source was used as a basis. The resulting hydrogen production rates and the corresponding hydrogen purity are also given in a table.

  2. Recovery process

    SciTech Connect

    Apffel, F.

    1989-06-13

    This patent describes a process for manufacturing char and hydrocarbons from discarded used tires. The process consists of: introducing the substantially whole tires into a reactor; pyrolyzing the substantially whole tires in a reaction chamber continuously at a temperature and pressure and for a reaction time sufficient to cause the tires to dissociate into a vapor and a solid phase; the pyrolyzing step including directly heating the tires with a radiant heat source at temperatures of 1000{sup 0} to 3000{sup 0}F; producing char from the solid phase; and processing the vapor phase to produce hydrocarbons.

  3. Processible Polyazomethines

    NASA Technical Reports Server (NTRS)

    Bryant, Robert G.

    1993-01-01

    Processibility enhanced by incorporating trifluoromethylbenzene units into molecules. Results of two unexpected properties: high solubility in common organic solvents and lack of crystallinity. Properties coupled with ability of this class of polymers to undergo exchange reactions at elevated temperatures allow these materials to moderate their molecular weights during processing, which affects resulting mechanical properties after processing. Fluorinated polyazomethines form amorphous films that have excellent mechanical properties. Used in moisture-free environments as electronic semiconducting films and adhesives, and as matrix resins for advanced structural composites.

  4. Do adaptive comanagement processes lead to adaptive comanagement outcomes? A multicase study of long-term outcomes associated with the national riparian service team's place-based riparian assistance

    Treesearch

    Jill A. Smedstad; Hannah. Gosnell

    2013-01-01

    Adaptive comanagement (ACM) is a novel approach to environmental governance that combines the dynamic learning features of adaptive management with the linking and network features of collaborative management. There is growing interest in the potential for ACM to resolve conflicts around natural resource management and contribute to greater social and ecological...

  5. Word Processing.

    ERIC Educational Resources Information Center

    McWilliams, Peter

    1982-01-01

    Describes the kinds of computer equipment needed for a personal word processing system. The characteristics and capabilities of specific devices, including keyboards, printers, and disk drives, are discussed. (JL)

  6. Manufacturing processes

    NASA Technical Reports Server (NTRS)

    Bennet, Jay; Brower, David; Levine, Stan; Walker, Ray; Wooten, John

    1991-01-01

    The following issues are covered: process development frequently lags behind material development, high fabrication costs, flex joints (bellows) - a continuing program, SRM fabrication-induced defects, and in-space assembly will require simplified design.

  7. Grants Process

    Cancer.gov

    The NCI Grants Process provides an overview of the end-to-end lifecycle of grant funding. Learn about the types of funding available and the basics for application, review, award, and on-going administration within the NCI.

  8. Anodizing Process

    NASA Technical Reports Server (NTRS)

    1983-01-01

    This anodizing process traces its origin to the 1960's when Reynolds Metals Company, under contract with Goddard Space Flight Center, developed a multipurpose anodizing electrolyte (MAE) process to produce a hard protective finish for spacecraft aluminum. MAE produces a high-density, abrasion-resistant film prior to the coloring step, in which the pores of the film are impregnated with a metallic form of salt. Tru-Color product applications include building fronts, railing, curtain walls, doors and windows.

  9. Multifractal Processes

    DTIC Science & Technology

    1999-01-01

    Processes 1 Introduction and Summary Fractal processes have been instrumental in a variety of fields ranging from the theory of fully developed...formalism in a stochastic setting . Thereby, the importance of higher order statistics will become evident. It might be especially appealing to the...rates occur in multifractal ‘trading time’ [68, 69]. With the theory developed in this paper, it be- comes an easy task to explore B1/2(M(t)) from the

  10. Power processing

    NASA Technical Reports Server (NTRS)

    Schwarz, F. C.

    1971-01-01

    Processing of electric power has been presented as a discipline that draws on almost every field of electrical engineering, including system and control theory, communications theory, electronic network design, and power component technology. The cost of power processing equipment, which often equals that of expensive, sophisticated, and unconventional sources of electrical energy, such as solar batteries, is a significant consideration in the choice of electric power systems.

  11. Processing of high performance (LRE)-Ba Cu O large, single-grain bulk superconductors in air

    NASA Astrophysics Data System (ADS)

    Hari Babu, N.; Iida, K.; Shi, Y.; Cardwell, D. A.

    2006-10-01

    We report the fabrication of large (LRE)BCO single-grains with improved superconducting properties for LRE = Nd, Sm and Gd using a practical process via both conventional top seeded melt growth (TSMG) and seeded infiltration-growth (SIG). This process uses a new generic seed crystal that promotes heterogeneous grain nucleation in the required orientation and suppresses the formation of solid solution in a controlled manner within individual grains by the addition of excess BaO2 to the precursor powder. The spatial distribution of the superconducting properties of LRE bulk superconductors as a function of BaO2 addition for large (LRE)BCO grains fabricated in air by TSMG and SIG for LRE = Gd, Sm and Nd are compared. The optimum BaO2 content required to fabricate single-grain (LRE)BCO with high and homogeneous Tc is determined from these experiments for each LRE system. The irreversibility fields of (LRE)BCO bulk superconductors processed in air are as high as those processed in reduced PO2. Critical current densities in excess of 105 A/cm2 at 77 K and higher trapped fields have been achieved in optimized (LRE)BCO superconductors fabricated in air for the first time.

  12. Natural language processing in pathology: a scoping review.

    PubMed

    Burger, Gerard; Abu-Hanna, Ameen; de Keizer, Nicolette; Cornet, Ronald

    2016-07-22

    Encoded pathology data are key for medical registries and analyses, but pathology information is often expressed as free text. We reviewed and assessed the use of NLP (natural language processing) for encoding pathology documents. Papers addressing NLP in pathology were retrieved from PubMed, Association for Computing Machinery (ACM) Digital Library and Association for Computational Linguistics (ACL) Anthology. We reviewed and summarised the study objectives; NLP methods used and their validation; software implementations; the performance on the dataset used and any reported use in practice. The main objectives of the 38 included papers were encoding and extraction of clinically relevant information from pathology reports. Common approaches were word/phrase matching, probabilistic machine learning and rule-based systems. Five papers (13%) compared different methods on the same dataset. Four papers did not specify the method(s) used. 18 of the 26 studies that reported F-measure, recall or precision reported values of over 0.9. Proprietary software was the most frequently mentioned category (14 studies); General Architecture for Text Engineering (GATE) was the most applied architecture overall. Practical system use was reported in four papers. Most papers used expert annotation validation. Different methods are used in NLP research in pathology, and good performances, that is, high precision and recall, high retrieval/removal rates, are reported for all of these. Lack of validation and of shared datasets precludes performance comparison. More comparative analysis and validation are needed to provide better insight into the performance and merits of these methods. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

  13. Organosolv Processes.

    PubMed

    Brosse, Nicolas; Hussin, Mohd Hazwan; Rahim, Afidah Abdul

    2017-03-10

    Biofuels and chemicals can be produced from lignocellulosic feedstocks using biotechnological processes. The effective utilization of carbohydrates from biomass for the production of biofuels necessitates the development of pretreatment technologies to enhance their enzymatic digestibility. Among all the various pretreatment methods currently studied and developed, the organosolv processes, in which organic solvents or aqueous organic solvent mixtures are used as the pretreatment medium, appear to be specially promising in the context of the biorefinery because (1) they produce cellulosic pulp with a good enzymatic digestibility for monomeric glucose production and (2) they allow a clean fractionation of the major biomass components (cellulose, lignin, and hemicelluloses) into three process streams. In this chapter we give an updated overview of organosolv methods using conventional solvents and ionic liquids which have recently gained considerable interest as solvents for lignocellulosic biomass and pretreatment.

  14. Process Analyzer

    NASA Technical Reports Server (NTRS)

    1994-01-01

    The ChemScan UV-6100 is a spectrometry system originally developed by Biotronics Technologies, Inc. under a Small Business Innovation Research (SBIR) contract. It is marketed to the water and wastewater treatment industries, replacing "grab sampling" with on-line data collection. It analyzes the light absorbance characteristics of a water sample, simultaneously detects hundreds of individual wavelengths absorbed by chemical substances in a process solution, and quantifies the information. Spectral data is then processed by ChemScan analyzer and compared with calibration files in the system's memory in order to calculate concentrations of chemical substances that cause UV light absorbance in specific patterns. Monitored substances can be analyzed for quality and quantity. Applications include detection of a variety of substances, and the information provided enables an operator to control a process more efficiently.

  15. Reforming process

    SciTech Connect

    Mitsche, R.T.; Pope, G.N.

    1981-01-06

    A process for reforming a naphtha feedstock is disclosed. The reforming process is effected at reforming conditions in contact with a catalyst comprising a platinum group metal component and a group iv-a metal component composited with an alumina support wherein said support is prepared by admixing an alpha alumina monohydrate with an aqueous ammoniacal solution having a ph of at least about 7.5 to form a stable suspension. A salt of a strong acid, e.g., aluminum nitrate, is commingled with the suspension to form an extrudable paste or dough. On extrusion, the extrudate is dried and calcined to form said alumina support.

  16. FLUORINATION PROCESS

    DOEpatents

    McMillan, T.S.

    1957-10-29

    A process for the fluorination of uranium metal is described. It is known that uranium will react with liquid chlorine trifluoride but the reaction proceeds at a slow rate. However, a mixture of a halogen trifluoride together with hydrogen fluoride reacts with uranium at a significantly faster rate than does a halogen trifluoride alone. Bromine trifluoride is suitable for use in the process, but chlorine trifluoride is preferred. Particularly suitable is a mixture of ClF/sub 3/ and HF having a mole ratio (moles

  17. Point Processes.

    DTIC Science & Technology

    1987-05-01

    ClaSIfication , 0.1102F 2304 Point processes____________ 12. PERSONAL AUTHORIS) Serfozo, R.F. 13AL TYPE OF REPORT 13b. TIME COVERED I4. DATE OF REPORT...the Laplace functional of M is as in Lemma 1.12. Keep in mind that a typical representation of a marked point process is o V 4 =. 1 6XnZ where N = 2 6...special case, for f: A - R . is X E[f(NO)] = E[JO f(O N)dt]. 0 Keep in mind that the expectation on the left is with respect to the probability for N

  18. Image Processing

    NASA Technical Reports Server (NTRS)

    1982-01-01

    Images are prepared from data acquired by the multispectral scanner aboard Landsat, which views Earth in four ranges of the electromagnetic spectrum, two visible bands and two infrared. Scanner picks up radiation from ground objects and converts the radiation signatures to digital signals, which are relayed to Earth and recorded on tape. Each tape contains "pixels" or picture elements covering a ground area; computerized equipment processes the tapes and plots each pixel, line be line to produce the basic image. Image can be further processed to correct sensor errors, to heighten contrast for feature emphasis or to enhance the end product in other ways. Key factor in conversion of digital data to visual form is precision of processing equipment. Jet Propulsion Laboratory prepared a digital mosaic that was plotted and enhanced by Optronics International, Inc. by use of the company's C-4300 Colorwrite, a high precision, high speed system which manipulates and analyzes digital data and presents it in visual form on film. Optronics manufactures a complete family of image enhancement processing systems to meet all users' needs. Enhanced imagery is useful to geologists, hydrologists, land use planners, agricultural specialists geographers and others.

  19. Information Processing.

    ERIC Educational Resources Information Center

    Jennings, Carol Ann; McDonald, Sandy

    This publication contains instructional materials for teacher and student use for a course in information processing. The materials are written in terms of student performance using measurable objectives. The course includes 10 units. Each instructional unit contains some or all of the basic components of a unit of instruction: performance…

  20. Budgeting Process

    ERIC Educational Resources Information Center

    Hentschke, Guilbert C.; Shaughnessy, John

    1973-01-01

    Discusses steps three and four in a budgeting process that uses Program Evaluation and Review Techniques (PERT). Step three involves developing time estimates and scheduling each of the activities in the PERT chart. Step four involves responsibility identification and coordination. (Author/JF)

  1. Image Processing

    DTIC Science & Technology

    1999-03-01

    blurs the processed image. Blurring is the primary limitation of low-pass filtering. Figure (10) shows a photo of the famous Taj -Hahal, one of the...Original Histo(p"am FILENAME.APP=41 06FG 1 O.PSD APPLICATION: ADOBE PHOTOSHOP VERSION 4.0 Figure (10) Photo ofTaj- Mahal with arbitrarily noise

  2. SEPARATION PROCESS

    DOEpatents

    Stoughton, R.W.

    1961-10-24

    A process for separating tetravalent plutonium from aqueous solutions and from niobium and zirconium by precipitation on lanthanum oxalate is described. The oxalate ions of the precipitate may be decomposed by heating in the presence of an oxidizing agent, forming a plutonium compound readily soluble in acid. (AEC)

  3. Fragmentation Processes

    NASA Astrophysics Data System (ADS)

    Whelan, Colm T.

    2012-12-01

    Preface; 1. Direct and resonant double-photoionization: from atoms to solids L. Avaldi and G. Stefani; 2. The application of propagation exterior complex scaling to atomic collisions P. L. Bartlett and A. T. Stelbovics; 3. Fragmentation of molecular-ion beams in intense ultra-short laser pulses I. Ben-Itzhak; 4. Atoms with one and two active electrons in strong laser fields I. A. Ivanov and A. S. Kheifets; 5. Experimental aspects of ionization studies by positron and positronium impact G. Laricchia, D. A. Cooke, Á. Kövér and S. J. Brawley; 6. (e,2e) spectroscopy using fragmentation processes J. Lower, M. Yamazaki and M. Takahashi; 7. A coupled pseudostate approach to the calculation of ion-atom fragmentation processes M. McGovern, H. R. J. Walters and C. T. Whelan; 8. Electron Impact Ionization using (e,2e) coincidence techniques from threshold to intermediate energies A. J. Murray; 9. (e,2e) processes on atomic inner shells C. T. Whelan; 10. Spin resolved atomic (e,2e) processes J. Lower and C. T. Whelan; Index.

  4. Processing Determinism

    ERIC Educational Resources Information Center

    O'Grady, William

    2015-01-01

    I propose that the course of development in first and second language acquisition is shaped by two types of processing pressures--internal efficiency-related factors relevant to easing the burden on working memory and external input-related factors such as frequency of occurrence. In an attempt to document the role of internal factors, I consider…

  5. On Process.

    ERIC Educational Resources Information Center

    Waxler, Robert P.

    1987-01-01

    Claims that the product approach to business writing prescribes a way of operating similar to imitation and creates an illusion of a static world when, in reality, the business environment is constantly in flux. Argues that the process approach to writing instruction should be used in business communication classes. (JD)

  6. Processing and properties of Bi 2Sr 2CaCu 2O x thick films on polycrystalline magnesium oxide substrates

    NASA Astrophysics Data System (ADS)

    Köbel, S.; Schneider, D.; Sager, D.; Sütterlin, P.; Fall, L.; Gauckler, L. J.

    2003-12-01

    In this paper we report on the processing parameters and resulting critical current densities of Bi 2Sr 2CaCu 2O x (Bi-2212) thick films on polycrystalline MgO substrates. Bi-2212 tapes were cast by the doctor blade technique and laminated onto flat MgO-ceramic substrates. The tapes were produced via the partial melt-process in a single cycle. Silver(I)oxide (Ag 2O) was added to the powder and the maximum process temperature was varied in order to optimize the transport current density at 77 K in self-field. It was found that both parameters, maximum process temperature during partial melting and amount of Ag 2O added have a strong influence on the critical current density at 77 K. The highest Jc of 1900 A/cm 2 was achieved in the 130 μm thick films with an addition of 4 wt% Ag 2O processed at a maximum temperature of 900 °C. In addition, large components were processed with 1 cm wide conductors meandering over 150 cm on 20 cm diameter MgO plates.

  7. Engineered Three-Dimensional Electrodes by HVOF Process for Hydrogen Production

    NASA Astrophysics Data System (ADS)

    Aghasibeig, Maniya; Moreau, Christian; Dolatabadi, Ali; Wuthrich, Rolf

    2016-12-01

    High velocity oxy-fuel process was used to prepare nickel electrode coatings for hydrogen production by alkaline water electrolysis. To further increase the active surface area of the electrodes, pyramidal fin arrays with two different sizes were deposited on the top surface of the electrodes using mesh screen masks. The surface microstructure, topology and roughness of the coatings were studied using scanning electron microscope, optical microscopy and confocal laser scanning microscopy. Steady-state polarization curves were used to evaluate the electrocatalytic activity of the electrodes. The performance of the electrodes coated using mesh outperformed the electrode deposited without using mesh. In addition, the electrode that was coated using the coarse mesh was characterized with the highest activity with the exchange current density and overpotential values of 9.3 × 10-3 A/cm2 and -306 mV, respectively. Formation of different roughness levels due to the combination of normal and off-normal impact of the coating particles on the surface of the fins was identified as the main factor for the increased activity of this electrode toward the hydrogen evolution reaction.

  8. Molecular beam epitaxy for advanced gate stack materials and processes

    NASA Astrophysics Data System (ADS)

    Locquet, Jean-Pierre

    2005-03-01

    The material requirements for future CMOS generations - as given by the ITRS roadmap - are very challenging. This includes a high K dielectric without a low K interfacial layer, a high mobility channel and the appropriate metal gate. With the help of two projects INVEST and ET4US, we are building up a molecular beam epitaxy (MBE) infrastructure to grow this material set on large area wafers that can be further processed into small scale devices. In the INVEST project, we have developed an MBE system for the growth of complex oxides on semiconductors. The system follows the overall design of a production tool and is equipped with an RF atomic oxygen source, effusion cells, e-beam evaporators and a differential pumping stage. The oxide growth process starts with desorbing the initial surface oxide on the Si wafers in ultra-high vacuum and high temperature to create a clean reconstructed 2x1 surface. Using the atomic oxygen it is possible to oxidize the surface in a well controlled manner at low temperature and to grow very thin and dense SiOx layers, followed by the growth of 2-6 nm amorphous high K dielectrics. The process parameters permit to tune the interface layer from a SiOx rich to a silicide rich interface with a significant impact on the capacitance and the leakage. Initial focus is on developing an optimized growth recipe for high quality amorphous HfO2 and LaHfO3.5 films. This recipe was subsequently used to make wafers for a transistor batch that gave us the first N short channel MBE MOSFET's (100 nm) using an etched gate process flow. Some highlights of the first batch for 3nm HfO2 MOSFET are a high mobility (> 270 cm^2/Vs) with a corresponding low leakage current of 2 mA/cm^2). While there were some process issues for LaHfO3.5, the 3 nm MOSFET showed very low leakage currents below 10-6 A/cm^2. Interestingly all the LaHFO3.5 MOSFETs showed very low threshold voltage instabilities. In collaboration with C. Marchiori, M. Sousa, A.Guiller, H. Siegwart, D

  9. Restoration Process

    NASA Technical Reports Server (NTRS)

    1979-01-01

    In the accompanying photos, a laboratory technician is restoring the once-obliterated serial number of a revolver. The four-photo sequence shows the gradual progression from total invisibility to clear readability. The technician is using a new process developed in an applications engineering project conducted by NASA's Lewis Research Center in conjunction with Chicago State University. Serial numbers and other markings are frequently eliminated from metal objects to prevent tracing ownership of guns, motor vehicles, bicycles, cameras, appliances and jewelry. To restore obliterated numbers, crime laboratory investigators most often employ a chemical etching technique. It is effective, but it may cause metal corrosion and it requires extensive preparatory grinding and polishing. The NASA-Chicago State process is advantageous because it can be applied without variation to any kind of metal, it needs no preparatory work and number recovery can be accomplished without corrosive chemicals; the liquid used is water.

  10. Process development

    NASA Technical Reports Server (NTRS)

    Bickler, D. B.

    1985-01-01

    An overview is given of seven process development activities which were presented at this session. Pulsed excimer laser processing of photovoltaic cells was presented. A different pulsed excimer laser annealing was described using a 50 w laser. Diffusion barrier research focused on lowering the chemical reactivity of amorphous thin film on silicon. In another effort adherent and conductive films were successfully achieved. Other efforts were aimed at achieving a simultaneous front and back junction. Microwave enhanced plasma deposition experiments were performed. An updated version of the Solar Array Manufacturing Industry Costing Standards (SAMICS) was presented, along with a life cycle cost analysis of high efficiency cells. The last presentation was on the evaluation of the ethyl vinyl acetate encapsulating system.

  11. Fermentation process

    SciTech Connect

    Lutzen, N.W.

    1982-02-23

    Fermentation process consists essentially of fermenting a 10-45% w/w aqueous slurry of granular starch for the production of ethanol with an ethanol-producing microorganism in the presence of alpha-amylase and glucoamylase, the conduct of said fermentation being characterized by low levels of dextrin and fermentable sugars in solution in the fermentation broth throughout the fermentation, and thereafter recovering enzymes from the fermentation broth for use anew in fermentation of granular starch.

  12. Optical Processing.

    DTIC Science & Technology

    1986-06-01

    general applications with average performance and certain numer- ical applications with very high per- formance. MIMD computers Support general ...Optical Processing I% FINAL REPORT June 1986 Heriot-Watt University University of Dayton Research Institute Subcontract Order No. RI-43109 ONR Main...apart, or a decoupled geometry in which the bias beamlet array, generated by the HOEs, is imaged by an intermediate, longer focal-length, high N.A. lens

  13. Veggie Processing

    NASA Image and Video Library

    2017-02-15

    Charles Spern, at right, project manager on the Engineering Services Contract (ESC), and Glenn Washington, ESC quality assurance specialist, perform final inspections of the Veggie Series 1 plant experiment inside a laboratory in the Space Station Processing Facility at NASA's Kennedy Space Center in Florida. The Series 1 experiment is being readied for flight aboard Orbital ATK's Cygnus module on its seventh (OA-7) Commercial Resupply Services mission to the International Space Station. The Veggie system is on the space station.

  14. Hydropyrolysis process

    DOEpatents

    Ullman, Alan Z.; Silverman, Jacob; Friedman, Joseph

    1986-01-01

    An improved process for producing a methane-enriched gas wherein a hydrogen-deficient carbonaceous material is treated with a hydrogen-containing pyrolysis gas at an elevated temperature and pressure to produce a product gas mixture including methane, carbon monoxide and hydrogen. The improvement comprises passing the product gas mixture sequentially through a water-gas shift reaction zone and a gas separation zone to provide separate gas streams of methane and of a recycle gas comprising hydrogen, carbon monoxide and methane for recycle to the process. A controlled amount of steam also is provided which when combined with the recycle gas provides a pyrolysis gas for treatment of additional hydrogen-deficient carbonaceous material. The amount of steam used and the conditions within the water-gas shift reaction zone and gas separation zone are controlled to obtain a steady-state composition of pyrolysis gas which will comprise hydrogen as the principal constituent and a minor amount of carbon monoxide, steam and methane so that no external source of hydrogen is needed to supply the hydrogen requirements of the process. In accordance with a particularly preferred embodiment, conditions are controlled such that there also is produced a significant quantity of benzene as a valuable coproduct.

  15. High-voltage AlGaN/GaN Schottky barrier diodes on silicon using a post-process O2 treatment

    NASA Astrophysics Data System (ADS)

    Seok, Ogyun; Han, Min-Koo; Byun, Young-Chul; Kim, Jiyoung; Shin, Hyun-Chang; Ha, Min-Woo

    2015-01-01

    High-voltage AlGaN/GaN Schottky barrier diodes (SBDs) were fabricated using on a silicon (1 1 1) substrate, and a post-process O2 treatment was carried out to reduce the leakage current and increase the breakdown voltage. Time-of-flight secondary ion mass spectroscopy revealed that, following the post-process O2 treatment, oxygen diffused into an AlGaN barrier and AlO was generated. A significant suppression of the leakage current (of approximately 6 orders of magnitude) occurred in the buffer isolation structures following the O2 treatment. Our method also resulted in suppression of the surface leakage current through the mesa-etched surface. A virgin GaN SBD exhibited a leakage current of 1.76 × 10-2 A/cm2, whereas the equivalent O2-treated device had a leakage current of 1.75 × 10-4 A/cm2 (the anode-cathode distance was LAC = 10 μm, and the applied bias was -100 V). This reduction in the leakage current was caused by surface passivation at the anode and cathode. The post-process O2 treatment also increased the breakdown voltage from Vb = 808 V to Vb = 1590 V for a device with LAC = 10 μm. GaN SBDs with and without the post-process O2 treatment exhibited low specific on-resistance of Ron,sp = 2.51 mΩ cm2 and Ron,sp = 2.48 mΩ cm2, respectively, with LAC = 10 μm. Devices with the post-process O2 treatment exhibited a figure of merit of Vb2/Ron,sp = 1006 MW/cm2, whereas devices without the O2 treatment exhibited a figure of merit of Vb2/Ron,sp = 263 MW/cm2. These high-voltage GaN SBDs employing the post-process O2 treatment are suitable for applications including DC-DC converters, inverters, and power factor correction circuits, where high voltage operation is required with low leakage currents.

  16. Ceramic Processing

    SciTech Connect

    EWSUK,KEVIN G.

    1999-11-24

    Ceramics represent a unique class of materials that are distinguished from common metals and plastics by their: (1) high hardness, stiffness, and good wear properties (i.e., abrasion resistance); (2) ability to withstand high temperatures (i.e., refractoriness); (3) chemical durability; and (4) electrical properties that allow them to be electrical insulators, semiconductors, or ionic conductors. Ceramics can be broken down into two general categories, traditional and advanced ceramics. Traditional ceramics include common household products such as clay pots, tiles, pipe, and bricks, porcelain china, sinks, and electrical insulators, and thermally insulating refractory bricks for ovens and fireplaces. Advanced ceramics, also referred to as ''high-tech'' ceramics, include products such as spark plug bodies, piston rings, catalyst supports, and water pump seals for automobiles, thermally insulating tiles for the space shuttle, sodium vapor lamp tubes in streetlights, and the capacitors, resistors, transducers, and varistors in the solid-state electronics we use daily. The major differences between traditional and advanced ceramics are in the processing tolerances and cost. Traditional ceramics are manufactured with inexpensive raw materials, are relatively tolerant of minor process deviations, and are relatively inexpensive. Advanced ceramics are typically made with more refined raw materials and processing to optimize a given property or combination of properties (e.g., mechanical, electrical, dielectric, optical, thermal, physical, and/or magnetic) for a given application. Advanced ceramics generally have improved performance and reliability over traditional ceramics, but are typically more expensive. Additionally, advanced ceramics are typically more sensitive to the chemical and physical defects present in the starting raw materials, or those that are introduced during manufacturing.

  17. Speech Processing.

    DTIC Science & Technology

    1983-05-01

    airborne environment. The SEU’s ability to remove narrowband types of noises automatically and in real-time by as much as forty (40) d& decibels would...cepstral process that can improve the signal-to-noise ratio of noisy communication channels as much as 12 to 14 decibels . An improvement of this amount in...and Forgie, C.A., 1959, "Results Obtained from a Vowel Recognition Computer Program", J. Acoust Soc. Am 31(11) 8. Vicens, P. 1969, "Aspects of

  18. RF processing

    NASA Astrophysics Data System (ADS)

    Burhans, R. W.

    1982-06-01

    The Loran-C radio frequency processing is discussed. A diagram which generally illustrates the automatic gain control is presented. The augmented differentiator for pulse envelopes adapts conventional communications receiver with wideband AM capability to detect pulse signals such as Loran-C. The circuit enhances reception for surveillance and observation of HF over-the-horizon radar signals or others where time difference estimates between pulse returns are of interest. The high resolution VLF spectrum which receives weak VLF signals by using an HP 3581A wave analyzer detecting signals with a very narrow bandwidth of only 3 Hz is also presented.

  19. Nonequilibrium processes.

    PubMed

    Polanyi, J C

    1971-08-01

    Nonequilibrium phenomena have been studied for over half a century, particularly as a means to understanding the mechanism of energy transfer. Application of the insights and techniques of molecular physics to chemistry has resulted in a view of chemistry as constituting an aspect of the study of strong collisions, and chemical reaction as a special type of energy transfer. Increasing use has been made in experimental work of nonequilibrium environments for the study of chemical processes. The nature and purpose of such experiments are reviewed here, very briefly, and an attempt is made to point to areas that appear ripe for development over the coming decade.

  20. Veggie Processing

    NASA Image and Video Library

    2017-02-15

    Charles Spern, at right, project manager on the Engineering Services Contract (ESC), and Glenn Washington, ESC quality assurance specialist, perform final inspections of the Veggie Series 1 plant experiment inside a laboratory in the Space Station Processing Facility at NASA's Kennedy Space Center in Florida. At far left is Dena Richmond, ESC configuration management. The Series 1 experiment is being readied for flight aboard Orbital ATK's Cygnus module on its seventh (OA-7) Commercial Resupply Services mission to the International Space Station. The Veggie system is on the space station.

  1. Signal processing

    NASA Astrophysics Data System (ADS)

    Norman, David M.

    The application of signal processing technology to conventional weapons systems can lower operator workloads and enhance kill probabilities, while automating wide-area surveillance, target search and classification, target tracking, and aimpoint selection. Immediate opportunities exist for automatic target cueing in underwater and over-the-horizon targeting, as well as for airborne multiple-target fire control. By embedding the transit/receive electronics into conformal aircraft sensor arrays, a 'smart' skin can be created. Electronically scanned phased arrays can be used to yield accurate azimuthal and elevation positions while nullifying EW threats. Attention is given to major development thrusts in algorithm design.

  2. Signal Processing

    DTIC Science & Technology

    1989-03-01

    ORGANIZATION Univ of Minnesota (f*fto U. S. Army Research Office 6c. ADDRESS (City, State, and ZIP Code) 7b. ADDRESS (Wiy Stat, and ZIP Code...Minneapolis, MN 55455 P. 0. Box 12211 Research Triangle Park, NC 27709-2211 Sa. NAME Of FUNDING ISPONSORING Sb. OFFICE SYMBOL 9. PROCUREMENT INSTRUMENT...PROJECT ITASK jWORK UNIT Research Triangle Park, NC 27709-2211 EMNTO.I NO NO CESOIO 11. TITLE (Incudt Security Classifiratio") Signal Processing of, he auth

  3. Combined Effect of Long Processing Time and Na2SiF6 on the Properties of PEO Coatings Formed on AZ91D

    NASA Astrophysics Data System (ADS)

    Rehman, Zeeshan Ur; Koo, Bon Heun

    2016-08-01

    In this study, protective ceramic coatings were prepared on AZ91D magnesium alloy by plasma electrolytic oxidation (PEO) to improve the corrosion and mechanical properties of AZ91D magnesium alloy. The process was conducted in silicate-fluoride-based electrolyte solution. It was found that the average micro-hardness of the coating was significantly increased with an increase in the PEO processing time. The highest value of the average micro-hardness ~1271.2 HV was recorded for 60-min processing time. The phase analysis of the coatings indicated that they were mainly composed of Mg2SiO4, MgO, and MgF2 phases. The surface and cross-sectional study demonstrated that porosity was largely reduced with processing time, together with the change in pore geometry from irregular to spherical shape. The results of the polarization test in 3.5 wt.% NaCl solution revealed that aggressive corrosion took place for 5-min sample; however, the corrosion current was noticeably decreased to 0.43 × 10-7 A/cm2 for the 60-min-coated sample. The superior nobility and hardness for long processing time are suggested to be due to the dense and highly thick coating, coupled with the presence of MgF2 phase.

  4. Fully solution-processed low-voltage aqueous In2O3 thin-film transistors using an ultrathin ZrO(x) dielectric.

    PubMed

    Liu, Ao; Liu, Guo Xia; Zhu, Hui Hui; Xu, Feng; Fortunato, Elvira; Martins, Rodrigo; Shan, Fu Kai

    2014-10-22

    We reported here "aqueous-route" fabrication of In2O3 thin-film transistors (TFTs) using an ultrathin solution-processed ZrOx dielectric thin film. The formation and properties of In2O3 thin films under various annealing temperatures were intensively examined by thermogravimetric analysis, Fourier transform infrared spectroscopy, and atomic force microscopy. The solution-processed ZrOx thin film followed by sequential UV/ozone treatment and low-temperature thermal-annealing processes showed an amorphous structure, a low leakage-current density (∼1 × 10(-9) A/cm(2) at 2 MV/cm), and a high breakdown electric field (∼7.2 MV/cm). On the basis of its implementation as the gate insulator, the In2O3 TFTs based on ZrOx annealed at 250 °C exhibit an on/off current ratio larger than 10(7), a field-effect mobility of 23.6 cm(2)/V·s, a subthreshold swing of 90 mV/decade, a threshold voltage of 0.13 V, and high stability. These promising properties were obtained at a low operating voltage of 1.5 V. These results suggest that "aqueous-route" In2O3 TFTs based on a solution-processed ZrOx dielectric could potentially be used for low-cost, low-temperature-processing, high-performance, and flexible devices.

  5. Optical processing

    NASA Astrophysics Data System (ADS)

    Gustafson, S. C.

    1985-12-01

    The technical contributions were as follows: (1) Optical parallel 2-D neighborhood processor and optical processor assessment technique; (2) High accuracy with moderately accurate components and optical fredkin gate architectures; (3) Integrated optical threshold computing, pipelined polynomial processor, and all optical analog/digital converter; (4) Adaptive optical associative memory model with attention; (5) Effectiveness of parallelism and connectivity in optical computers; (6) Optical systolic array processing using an integrated acoustooptic module; (7) Optical threshold elements and networks, holographic threshold processors, adaptive matched spatial filtering, and coherence theory in optical computing; (8) Time-varying optical processing for sub-pixel targets, optical Kalman filtering, and adaptive matched filtering; (9) Optical degrees of freedom, ultra short optical pulses, number representations, content-addressable-memory processors, and integrated optical Givens rotation devices; (10) Optical J-K flip flop analysis and interfacing for optical computers; (11) Matrix multiplication algorithms and limits of incoherent optical computers; (12) Architecture for machine vision with sensor fusion, pattern recognition functions, and neural net implementations; (13) Optical computing algorithms, architectures, and components; and (14) Dynamic optical interconnections, advantages and architectures.

  6. Lithospheric processes

    SciTech Connect

    Baldridge, W.S.; Wohletz, K.; Fehler, M.C.

    1997-11-01

    This is the final report of a three-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The main objective was to improve understanding of the origin and evolution of the Earth`s lithosphere by studying selected processes, such as deformation and magmatic intrusion during crustal extension, formation and extraction of mantle melts, fluid transport of heat and mass, and surface processes that respond to deep-seated events. Additional objectives were to promote and develop innovative techniques and to support relevant educational endeavors. Seismic studies suggest that underplating of crust by mantle melts is an important crustal-growth mechanism, that low-angle faults can be seismogenic, and that shear deformation creates mantle anisotropy near plate boundaries. Results of geochemical work determined that magmas from oceanic intraplate islands are derived from a uniform depth in the upper mantle, whereas melts erupted at mid-ocean ridges are mixed from a range of depths. The authors have determined the extent and style of fluid infiltration and trace-element distribution in natural magmatic systems, and, finally, investigated {sup 21}Ne as a tool for dating of surficial materials.

  7. Physicochemical processes

    SciTech Connect

    Matsumoto, M.R.; Jensen, J.N.; McGinley, P.M.; Reed, B.E.

    1993-06-01

    A variety of waste water treatment processes are reported. Destruction of free and organically bound cyanides by alkaline hydrolysis in a pipeline reactor was studied. A bench-scale pilot system combining coagulation, sedimentation, and ultrafiltration to study treatment of animal wastewater was developed. A pilot limestone contactor was evaluated for its ability to treat a low pH, low alkalinity surface water supply for corrosion control, and as a conditioning step for flocculation. Experiments were conducted with a falling film reactor to determine the potential of freeze concentration to treat municipal wastewater for reuse. The effects of reductants and alkali on the sludge quantity from chromium(VI) wastes and the leachability and physical properties of solidified chromium sludge were investigated. Development and experience with a pilot-scale surfactant washing-flushing system to remove polychlorinated biphenyls (PCBs) from contaminated soils was reported.

  8. Lithospheric processes

    SciTech Connect

    Baldridge, W.

    2000-12-01

    The authors used geophysical, geochemical, and numerical modeling to study selected problems related to Earth's lithosphere. We interpreted seismic waves to better characterize the thickness and properties of the crust and lithosphere. In the southwestern US and Tien Shari, crust of high elevation is dynamically supported above buoyant mantle. In California, mineral fabric in the mantle correlate with regional strain history. Although plumes of buoyant mantle may explain surface deformation and magmatism, our geochemical work does not support this mechanism for Iberia. Generation and ascent of magmas remains puzzling. Our work in Hawaii constrains the residence of magma beneath Hualalai to be a few hundred to about 1000 years. In the crust, heat drives fluid and mass transport. Numerical modeling yielded robust and accurate predictions of these processes. This work is important fundamental science, and applies to mitigation of volcanic and earthquake hazards, Test Ban Treaties, nuclear waste storage, environmental remediation, and hydrothermal energy.

  9. Polymerization process

    SciTech Connect

    Kostelnik, R.J.

    1987-03-03

    An improved process is described for preparing a hydrocarbon fluid friction reducing composition comprising mixing two or more alpha-monoolefins having 2 to about 30 carbon atoms in a diluent or an organic solvent and copolymerizing the alpha-monoolefins in the presence of a catalyst. The catalyst is comprised of a reducible or reduced titanium halide and an organo metal catalyst activator consisting of, per each 100 total moles of activator, about 1 to 20 moles of at least one trialkylaluminium compound, each alkyl group of which has 1 to 10 carbon atoms and about 99 to 80 moles of at least one dialkylaluminium halide compound, each alkyl group of which has 1 to about 10 carbon atoms. The mole ratio of activator to catalyst in the reaction mixture is in the range of about 0.001:1 to 50:1.

  10. Oligomerization process

    DOEpatents

    Smith, L.A. Jr.; Hearn, D.; Jones, E.M. Jr.

    1991-03-26

    A liquid phase process is described for oligomerization of C[sub 4] and C[sub 5] isoolefins or the etherification thereof with C[sub 1] to C[sub 6] alcohols wherein the reactants are contacted in a reactor with a fixed bed acid cation exchange resin catalyst at an LHSV of 5 to 20, pressure of 0 to 400 psig and temperature of 120 to 300 F wherein the improvement is the operation of the reactor at a pressure to maintain the reaction mixture at its boiling point whereby at least a portion but less than all of the reaction mixture is vaporized. By operating at the boiling point and allowing a portion of the reaction mixture to vaporize, the exothermic heat of reaction is dissipated by the formation of more boil up and the temperature in the reactor is controlled. 2 figures.

  11. Process Analyzer

    NASA Technical Reports Server (NTRS)

    1993-01-01

    Under a NASA Small Business Innovation Research (SBIR) contract, Axiomatics Corporation developed a shunting Dielectric Sensor to determine the nutrient level and analyze plant nutrient solutions in the CELSS, NASA's space life support program. (CELSS is an experimental facility investigating closed-cycle plant growth and food processing for long duration manned missions.) The DiComp system incorporates a shunt electrode and is especially sensitive to changes in dielectric property changes in materials at measurements much lower than conventional sensors. The analyzer has exceptional capabilities for predicting composition of liquid streams or reactions. It measures concentrations and solids content up to 100 percent in applications like agricultural products, petrochemicals, food and beverages. The sensor is easily installed; maintenance is low, and it can be calibrated on line. The software automates data collection and analysis.

  12. Image Processing

    NASA Technical Reports Server (NTRS)

    1993-01-01

    Electronic Imagery, Inc.'s ImageScale Plus software, developed through a Small Business Innovation Research (SBIR) contract with Kennedy Space Flight Center for use on space shuttle Orbiter in 1991, enables astronauts to conduct image processing, prepare electronic still camera images in orbit, display them and downlink images to ground based scientists for evaluation. Electronic Imagery, Inc.'s ImageCount, a spin-off product of ImageScale Plus, is used to count trees in Florida orange groves. Other applications include x-ray and MRI imagery, textile designs and special effects for movies. As of 1/28/98, company could not be located, therefore contact/product information is no longer valid.

  13. WELDING PROCESS

    DOEpatents

    Zambrow, J.; Hausner, H.

    1957-09-24

    A method of joining metal parts for the preparation of relatively long, thin fuel element cores of uranium or alloys thereof for nuclear reactors is described. The process includes the steps of cleaning the surfaces to be jointed, placing the sunfaces together, and providing between and in contact with them, a layer of a compound in finely divided form that is decomposable to metal by heat. The fuel element members are then heated at the contact zone and maintained under pressure during the heating to decompose the compound to metal and sinter the members and reduced metal together producing a weld. The preferred class of decomposable compounds are the metal hydrides such as uranium hydride, which release hydrogen thus providing a reducing atmosphere in the vicinity of the welding operation.

  14. Etherification process

    DOEpatents

    Smith, L.A. Jr.; Hearn, D.; Jones, E.M. Jr.

    1990-08-21

    A liquid phase process is described for oligomerization of C[sub 4] and C[sub 5] isoolefins or the etherification thereof with C[sub 1] to C[sub 6] alcohols wherein the reactants are contacted in a reactor with a fixed bed acid cation exchange resin catalyst at an LHSV of 5 to 20, pressure of 0 to 400 psig and temperature of 120 to 300 F wherein the improvement is the operation of the reactor at a pressure to maintain the reaction mixture at its boiling point whereby at least a portion but less than all of the reaction mixture is vaporized. By operating at the boiling point and allowing a portion of the reaction mixture to vaporize, the exothermic heat of reaction is dissipated by the formation of more boil up and the temperature in the reactor is controlled. 2 figs.

  15. Retorting process

    SciTech Connect

    Reynolds, B.A.

    1984-06-19

    Fines in the overhead vapors from an oil shale retort process in which fresh shale together with hot recycle combusted shale from a combustor are fed to a retort and at least partly fluidized by a countercurrent stripping gas stream are handled by removing a portion of the fines in a vapor-solid separation optionally subjecting the portion of fines to additional retorting in a fines retort condensing the partially dedusted gas separating the condensate into a substantially finesfree liquid oil and a wet solids and recycling at least a portion of the wet solids to the retort, fines retort, and/or combustor whereby the liquid on the wet solids is recovered and/or burned and the wet solids are dried.

  16. Crystallization process

    DOEpatents

    Adler, Robert J.; Brown, William R.; Auyang, Lun; Liu, Yin-Chang; Cook, W. Jeffrey

    1986-01-01

    An improved crystallization process is disclosed for separating a crystallizable material and an excluded material which is at least partially excluded from the solid phase of the crystallizable material obtained upon freezing a liquid phase of the materials. The solid phase is more dense than the liquid phase, and it is separated therefrom by relative movement with the formation of a packed bed of solid phase. The packed bed is continuously formed adjacent its lower end and passed from the liquid phase into a countercurrent flow of backwash liquid. The packed bed extends through the level of the backwash liquid to provide a drained bed of solid phase adjacent its upper end which is melted by a condensing vapor.

  17. Oligomerization process

    DOEpatents

    Smith, Jr., Lawrence A.; hearn, Dennis; Jones, Jr., Edward M.

    1991-01-01

    A liquid phase process for oligomerization of C.sub.4 and C.sub.5 isoolefins or the etherification thereof with C.sub.1 to C.sub.6 alcohols wherein the reactants are contacted in a reactor with a fixed bed acid cation exchange resin catalyst at an LHSV of 5 to 20, pressure of 0 to 400 psig and temperature of 120 to 300.degree. F. wherein the improvement is the operation of the reactor at a pressure to maintain the reaction mixture at its boiling point whereby at least a portion but less than all of the reaction mixture is vaporized. By operating at the boiling point and allowing a portion of the reaction mixture to vaporize, the exothermic heat of reaction is dissipated by the formation of more boil up and the temperature in the reactor is controlled.

  18. Etherification process

    DOEpatents

    Smith, Jr., Lawrence A.; Hearn, Dennis; Jones, Jr., Edward M.

    1990-01-01

    A liquid phase process for oligomerization of C.sub.4 and C.sub.5 isoolefins or the etherification thereof with C.sub.1 to C.sub.6 alcohols wherein the reactants are contacted in a reactor with a fixed bed acid cation exchange resin catalyst at an LHSV of 5 to 20, pressure of 0 to 400 psig and temperature of 120.degree. to 300.degree. F. wherein the improvement is the operation of the reactor at a pressure to maintain the reaction mixture at its boiling point whereby at least a portion but less than all of the reaction mixture is vaporized. By operating at the boiling point and allowing a portion of the reaction mixture to vaporize, the exothermic heat of reaction is dissipated by the formation of more boil up and the temperature in the reactor is controlled.

  19. Dairy processing.

    PubMed

    Bailey, Kenneth W

    2003-07-01

    The United States dairy processing sector is dynamic and adaptive to new changes in the market place. Changes in consumer preferences and manufacturing technologies are resulting in new challenges to the processing sector. Consumers want a wider array of quality dairy products. Fluid processors are adapting to changing consumer demands for beverage products by introducing new flavors, providing ultrapasteurization, and using creative packaging. In addition, United States food manufacturers are requesting dairy processors to provide new dairy fractions such as MPC for new nutrition products. United States dairy policy is attempting to adapt to these changes. Federal order reform has resulted in new market-oriented signals for dairy farmers to produce what the market wants; namely, quality milk components. US dairy farmers, however, also wants to maintain programs such as the DPSP that have had the unfortunate consequence of spurring demand for protein imports (i.e., MPCs, casein, and caseinates) and also resulted in a disincentive to produce these new innovative protein products here in the United States. Surplus skim milk solids are now moving into US Government warehouses rather than into commercial markets. The future of the United States dairy industry will clearly be toward producing innovative products that the market wants. There is a strong market for dairy products not only here in the United States but also overseas, which will mean learning to compete on a global scale. The challenge is to modernize our United States milk pricing programs to provide dairy farmers and processors proper price signals while providing a minimum level of support to dairy farmers. The benefit of a greater orientation toward the market place will be stronger rates of growth for United States-produced dairy products.

  20. Process Condition Considered Preparation and Characterization of Plasma Polymerized Methyl Methacrylate Thin Films for Organic Thin Film Transistor Application

    NASA Astrophysics Data System (ADS)

    Lee, Se-Hyun; Lee, Boong-Joo; Lim, Young-Taek; Lim, Jae-Sung; Lee, Sunwoo; Ochiai, Shizuyasu; Yi, Jun-Sin; Shin, Paik-Kyun

    2012-02-01

    Plasma polymerized methyl methaclylate (ppMMA) thin films were prepared with various process conditions such as inductively coupled plasma (ICP) power, substrate bias power, working pressure, substrate heating temperature, substrate position, and monomer flow rate. Thickness, surface morphology, dielectric constant, and leakage current of the ppMMA thin films were investigated for application to organic thin film transistor as gate dielectric. Deposition rate of over 8.6 nm/min, dielectric constant of 3.4, and leakage current density of 8.9 ×10-9 A/cm-2 at electric field of 1 MV/cm were achieved for the ppMMA thin film prepared at the optimized process condition: plasma power of RF 100 W; Ar flow rate of 20 sccm; working pressure of 5 mTorr; substrate temperature of 100 °C substrate position of 100 mm. The ppMMA thin film was then applied to pentacene based organic thin film transistor (OTFT) device fabrication. The OTFT device with 80 nm thick pentacene semiconductor layer showed field effect mobility of 0.144 cm2 V-1 s-1 and threshold voltage of -1.72 V.

  1. Efficient mineralization of the antibiotic trimethoprim by solar assisted photoelectro-Fenton process driven by a photovoltaic cell.

    PubMed

    Zhang, Yanyu; Wang, Aimin; Tian, Xiujun; Wen, Zhenjun; Lv, Hanjiao; Li, Desheng; Li, Jiuyi

    2016-11-15

    In this study, a novel self-sustainable solar assisted photoelectro-Fenton (SPEF) system driven by a solar photovoltaic cell was developed for the efficient mineralization of antibiotic trimethoprim (TMP) in water. A comparative degradation of 200mgL(-1) TMP by RuO2/Ti anodic oxidation (AO), anodic oxidation with H2O2 electrogeneration (AO-H2O2), electro-Fenton (EF) and SPEF was investigated. SPEF was proved to exhibit the highest oxidation power, i.e., more than 80% TOC was removed after 360min SPEF treatment of 200mgL(-1) of TMP under optimal conditions at pH 3.0, 1.0mM Fe(2+) and 18mAcm(-2). Influences of current density, pH, initial Fe(2+) and initial TMP concentration on SPEF process were also studied. Ten aromatic intermediates generated from hydroxylation, carbonylation and demethylation reactions were identified using UPLC-QTOF-MS/MS system during the SPEF treatment, together with three carboxylic acids (oxamic, oxalic and formic acids) and two inorganic ions (NH4(+) and NO3(-)) measured. Therefore, a reasonable pathway of TMP degradation in SPEF process was proposed.

  2. Effect of growth temperature on properties of bulk GdBa2Cu3Oy superconductors grown by IG process

    NASA Astrophysics Data System (ADS)

    Nakanishi, Y.; Naik, S. Pavan Kumar; Muralidhar, M.; Murakami, M.

    2017-07-01

    Recently, the flux pinning performance of Y-123 material was dramatically improved by optimizing the processing conditions during the Infiltration-Growth (IG) process. In the present work, we adapted the top- seeded IG technique and produced several 20 wt.% AgO2 doped bulk GdBa2Cu3Oy (GdBCO or Gd-123) samples at different growth temperatures of 983, 985, 986, 987, 989, 990, and 992 °C with the same holding time of 25 h. Our results indicate that the bulk GdBCO samples dwelled at 986 °C is the optimum temperature to produce large Gd-123 growth without spontaneous nucleation. Magnetization measurements on 986 °C dwelled composite showed a sharp superconducting transition with T c, onset at 93.6 K. The critical current density at 77 K and self-field was 16,500 A/cm2. The critical current density values are correlated with the microstructural changes in the bulk Gd-123 materials.

  3. Graduate and professional development in imaging and optical signal processing and related fields

    NASA Astrophysics Data System (ADS)

    Campbell, Jonathan G.; Murtagh, Fionn D.; Kokuer, Munevver

    2003-03-01

    Image processing, signal processing and computer vision are increasing in importance, and are indeed slowly being considered as core competences in computer science. The specification of computing curricula by the ACM and the IEEE Computer Society states that technical advances over the past decade have increased the importance of topics such as graphics and multimedia, and considers as a core topic Graphics and Visual Computing. With the advent of courses in digital media in electrical engineering and computer science, the increasing importance of computer imaging and vision is manifest, and not only in electrical engineering and computer science departments. The need for development and training of research students is more often than not badly catered for at the present time in Irish universities (Republic, Northern Ireland). Research students are often from diverse discipline and educational system backgrounds. A characteristic of a dynamic and effective graduate and research student environment is not just the raw numbers of PhDs produced, but also relative consensus on the part of the 'community' on the most effective major directions of innovation and of focus. On any such qualitative characteristic, Irish universities, institutes of technology and research institutes are not performing well. Successful models for such community-strengthening include doctoral networks at European level, and summer schools at national or regional level. This paper addresses specific issues: (i) the means by which the needs for graduate research level community-strengthening in the areas of signal processing, and image processing and computer vision, can be satisfied; (ii) what the most crucial elements of these fields are, i.e. proposed key areas and curricula.

  4. Self-assembled albumin nanoparticles as a nanocarrier for aclacinomycin A

    NASA Astrophysics Data System (ADS)

    Gong, Guangming; Liu, Wenya; Wang, Shudong

    2016-11-01

    This study aimed to reduce the cytotoxicity and improve the targeting of aclacinomycin (ACM) by covalently coupling it with amino-oxyacetic acid (AOA) to generate an active intermediate, AOA-ACM. AOA-ACM was conjugated with self-assembled human serum albumin (HSA) nanoparticles constructed using tris(2-carboxyethyl)phosphine (TCEP) as disulfide bond breaking molecules in an ‘opening stage-intermediate-closing stage’ route, in which the hydrophobic interaction, interchange of sulfhydryl and hydrogen bond may be the key factors in the assembling process. Conjugation between ACM and albumin nanoparticles was found to occur at an ACM ketone site using 1H-NMR and 13C-NMR matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass analysis indicated that the drug loading efficiency of ACM conjugated with HSA nanoparticles (NPs-ACM) was 7.4% (molar ratio = 6:1). The release of NPs-ACM was pH dependent. In vivo studies indicated that NPs-ACM exhibited fourfold higher tumor targeting capability on S180-tumor-bearing mice compared with the free ACM (p < 0.05). The cytotoxictiy and cardiotoxicity of NPs-ACM was reduced compared with the free ACM. Albumin carrier altered the blood pharmacokinetics and distribution of ACM. Hence, the NPs-ACM prodrug is ideal tumor targeting drug carriers for ACM, and the easy approach developed in this study for active intermediate and prodrug preparation can be applied to other pharmacological substances containing ketone groups. The method of preparing HSA-blank nanoparticles through TCEP reduction could be adopted to improve the water solubility of lipophilic drugs and their tumor-targeting specificity by fabricating HSA-lipophilic drug nanoparticles.

  5. Self-assembled albumin nanoparticles as a nanocarrier for aclacinomycin A.

    PubMed

    Gong, Guangming; Liu, Wenya; Wang, Shudong

    2016-11-18

    This study aimed to reduce the cytotoxicity and improve the targeting of aclacinomycin (ACM) by covalently coupling it with amino-oxyacetic acid (AOA) to generate an active intermediate, AOA-ACM. AOA-ACM was conjugated with self-assembled human serum albumin (HSA) nanoparticles constructed using tris(2-carboxyethyl)phosphine (TCEP) as disulfide bond breaking molecules in an 'opening stage-intermediate-closing stage' route, in which the hydrophobic interaction, interchange of sulfhydryl and hydrogen bond may be the key factors in the assembling process. Conjugation between ACM and albumin nanoparticles was found to occur at an ACM ketone site using (1)H-NMR and (13)C-NMR matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass analysis indicated that the drug loading efficiency of ACM conjugated with HSA nanoparticles (NPs-ACM) was 7.4% (molar ratio = 6:1). The release of NPs-ACM was pH dependent. In vivo studies indicated that NPs-ACM exhibited fourfold higher tumor targeting capability on S180-tumor-bearing mice compared with the free ACM (p < 0.05). The cytotoxictiy and cardiotoxicity of NPs-ACM was reduced compared with the free ACM. Albumin carrier altered the blood pharmacokinetics and distribution of ACM. Hence, the NPs-ACM prodrug is ideal tumor targeting drug carriers for ACM, and the easy approach developed in this study for active intermediate and prodrug preparation can be applied to other pharmacological substances containing ketone groups. The method of preparing HSA-blank nanoparticles through TCEP reduction could be adopted to improve the water solubility of lipophilic drugs and their tumor-targeting specificity by fabricating HSA-lipophilic drug nanoparticles.

  6. Publication process

    NASA Astrophysics Data System (ADS)

    Russell, C. T.; Reiff, P. H.

    Those who have contributed to the research literature are quite familiar with the workings of the publication process, even though they may not have seen it explicitly set down as is done in the accompanying flow chart. However, for the benefit of students, who are thought to read Eos, if only for the classified ads, and editors, who may have lost sight of the forest for the trees, we have requested that AGU publish this diagram. T h e flow chart is self-explanatory. We note that ΔtA,ΔtE, and ΔtR are time delays introduced by the author, the editor, and the referee. Since the editor gets to handle the paper twice each iteration (the number of which is counted by the index, I) he is responsible for a time delay of 2 ΔtE. The number NJ is journal dependent, ranging from 0 for some conference proceedings and forprofit journals, to 2 (or greater) for some AGU journals. (For example, this is our third submittal of this forum.) We would particularly like to thank G.C. Reid and S. Solomon and the many others who have had a hand in codifying this flow chart over the years and Eos editor, L.J. Lanzerotti, for his assistance in the further refinement of various details.

  7. Photoelectric characteristics of InGaP/Ga(In)As/Ge solar cells fabricated with a single-stage wet chemical etching separation process

    NASA Astrophysics Data System (ADS)

    Kalinovsky, Vitaly S.; Grebenshchikova, Elena A.; Dmitriev, Pavel A.; Il'inskaya, Natalia D.; Kontrosh, Evgeny V.; Malevskaya, Alexandra V.; Usikova, Anna A.; Andreev, Viacheslav M.

    2014-09-01

    In this work we present a post-growth fabrication process, in which the separation of InGaP/Ga(In)As/Ge epitaxial wafers into individual elements is done in a single-stage wet chemical etching process, which produces a smooth etching profile. This process makes it easier to apply a passivating protective layer to the element mesa sidewall, increasing both average cell efficiency and reliability. To assess fabricated multi-junction solar cell quality, dark J-V characteristics were measured directly on the epitaxial wafer at current densities of (1ṡ10-12 - 10) A/cm2 and voltages of (0 - 3) V. The dominating current flow mechanisms and their corresponding pre-exponential factors J0i were determined, and estimates of cell efficiencies made. We have demonstrated that the post-growth processes with single-stage separation etching of InGaP/Ga(In)As/Ge epitaxial wafers allows fabricating multi-junction solar cells with very similar J-V characteristics, similar low values of pre-exponential factors corresponding to "tunnel-trap" (overabundant) and "recombination" current flow mechanisms and high efficiencies.

  8. Dynamic Processes

    NASA Astrophysics Data System (ADS)

    Klingshirn, C.

    . Phys. Lett. 92:211105, 2008). For this point, recall Figs. 6.16 and 6.33. Since the polarisation amplitude is gone in any case after the recombination process, there is an upper limit for T 2 given by T 2 ≤ 2 T1. The factor of two comes from the fact that T 2 describes the decay of an amplitude and T 1 the decay of a population, which is proportional to the amplitude squared. Sometimes T 2 is subdivided in a term due to recombination described by T 1 and another called 'pure dephasing' called T 2 ∗ with the relation 1 / T 2 = 1 / 2 T 1 + 1 / T2 ∗. The quantity T 2 ∗ can considerably exceed 2 T 1. In the part on relaxation processes that is on processes contributing to T 3, we give also examples for the capture of excitons into bound, localized, or deep states. For more details on dynamics in semiconductors in general see for example, the (text-) books [Klingshirn, Semiconductor Optics, 3rd edn. (Springer, Berlin, 2006); Haug and Koch, Quantum Theory of the Optical and Electronic Properties of Semiconductors, 4th edn. (World Scientific, Singapore, 2004); Haug and Jauho, Quantum Kinetics in Transport and Optics of Semiconductors, Springer Series in Solid State Sciences vol. 123 (Springer, Berlin, 1996); J. Shah, Ultrafast Spectroscopy of Semiconductors and of Semiconductor Nanostructures, Springer Series in Solid State Sciences vol. 115 (Springer, Berlin, 1996); Schafer and Wegener, Semiconductor Optics and Transport Phenomena (Springer, Berlin, 2002)]. We present selected data for free, bound and localized excitons, biexcitons and electron-hole pairs in an EHP and examples for bulk materials, epilayers, quantum wells, nano rods and nano crystals with the restriction that - to the knowledge of the author - data are not available for all these systems, density ranges and temperatures. Therefore, we subdivide the topic below only according to the three time constants T 2, T 3 and T 1.

  9. Data Processing

    NASA Astrophysics Data System (ADS)

    Grangeat, P.

    A new area of biology has been opened up by nanoscale exploration of the living world. This has been made possible by technological progress, which has provided the tools needed to make devices that can measure things on such length and time scales. In a sense, this is a new window upon the living world, so rich and so diverse. Many of the investigative methods described in this book seek to obtain complementary physical, chemical, and biological data to understand the way it works and the way it is organised. At these length and time scales, only dedicated instrumentation could apprehend the relevant phenomena. There is no way for our senses to observe these things directly. One important field of application is molecular medicine, which aims to explain the mechanisms of life and disease by the presence and quantification of specific molecular entities. This involves combining information about genes, proteins, cells, and organs. This in turn requires the association of instruments for molecular diagnosis, either in vitro, e.g., the microarray or the lab-on-a-chip, or in vivo, e.g., probes for molecular biopsy, and tools for molecular imaging, used to localise molecular information in living organisms in a non-invasive way. These considerations concern both preclinical research for drug design and human medical applications. With the development of DNA and RNA chips [1], genomics has revolutionised investigative methods for cells and cell processes [2,3]. By sequencing the human genome, new ways have been found for understanding the fundamental mechanisms of life [4]. A revolution is currently under way with the analysis of the proteome [5-8], i.e., the complete set of proteins that can be found in some given biological medium, such as the blood plasma. The goal is to characterise certain diseases by recognisable signatures in the proteomic profile, as determined from a blood sample or a biopsy, for example [9-13]. What is at stake is the early detection of

  10. Information Processing - Administrative Data Processing

    NASA Astrophysics Data System (ADS)

    Bubenko, Janis

    A three semester, 60-credit course package in the topic of Administrative Data Processing (ADP), offered in 1966 at Stockholm University (SU) and the Royal Institute of Technology (KTH) is described. The package had an information systems engineering orientation. The first semester focused on datalogical topics, while the second semester focused on the infological topics. The third semester aimed to deepen the students’ knowledge in different parts of ADP and at writing a bachelor thesis. The concluding section of this paper discusses various aspects of the department’s first course effort. The course package led to a concretisation of our discipline and gave our discipline an identity. Our education seemed modern, “just in time”, and well adapted to practical needs. The course package formed the first concrete activity of a group of young teachers and researchers. In a forty-year perspective, these people have further developed the department and the topic to an internationally well-reputed body of knowledge and research. The department has produced more than thirty professors and more than one hundred doctoral degrees.

  11. An Investigation of the Squadron Air Combat Training System (HAVE ACME)

    DTIC Science & Technology

    1996-06-01

    flight) ALOAD Trajectory/Maneuver Gs (Og for straight and level flight) AOA Angle of attack in degrees PITCH Elevation angle of the aircraft longitudinal axis...in degrees YAW Azimuth angle between the aircraft longitudinal axis and North in degrees ROLL Roll angle of transverse/wing axis about

  12. Proceedings of the ACM-SIGSAM 1989 international symposium on symbolic and algebraic computation

    SciTech Connect

    Not Available

    1989-01-01

    This book contain subjects under the following topics: Gencray: A portable code generator for Cray fortan; massively parallel symbolic computation; reduction of group constructions to point stabilizers; and constrained equational reasoning.

  13. Micro-Stirling Active Cooling Module (MS/ACM) for DoD Electronics Systems

    DTIC Science & Technology

    2012-03-01

    coolers the dominant type of cooler for cooling space-based electronics. In theory, the Stirling refrigeration cycle can achieve the Carnot COP (the...indicates the ideal Stirling refrigeration cycle achieves the Carnot COP, which is the theoretical maximum possible achievable COP. However...overcoming the technical challenges. Finally we describe the wide range of applications for Stirling- cycle coolers, cryocoolers, and generators

  14. Career Patterns, Employment and Earnings of Graduates of 11 ACM Colleges.

    ERIC Educational Resources Information Center

    Wishart, Patricia; Rossmann, Jack

    A study was conducted of 11 private liberal arts colleges, all members of the Associated Colleges of the Midwest, to relate the career experiences of four graduating classes to their college experiences. The study was conducted as part of the National Project 1, Better Information for Student Choice, supported by the Fund for the Improvement of…

  15. 1973 Winter Simulation Conference. Sponsored by ACM/AIIE/SHARE/SCi/TIMS.

    ERIC Educational Resources Information Center

    Hoggatt, Austin Curwood, Ed.

    A record of the current state of the art of simulation and the major part it now plays in policy formation in large organizations is provided by these conference proceedings. The 40 papers presented reveal an emphasis on the applications of simulation. In addition, the abstracts of 28 papers submitted to a more informal "paper fair" are also…

  16. Career Patterns, Employment and Earnings of Graduates of 11 ACM Colleges.

    ERIC Educational Resources Information Center

    Wishart, Patricia; Rossmann, Jack

    A study was conducted of 11 private liberal arts colleges, all members of the Associated Colleges of the Midwest, to relate the career experiences of four graduating classes to their college experiences. The study was conducted as part of the National Project 1, Better Information for Student Choice, supported by the Fund for the Improvement of…

  17. USL NASA/RECON project presentations at the 1985 ACM Computer Science Conference: Abstracts and visuals

    NASA Technical Reports Server (NTRS)

    Dominick, Wayne D. (Editor); Chum, Frank Y.; Gallagher, Suzy; Granier, Martin; Hall, Philip P.; Moreau, Dennis R.; Triantafyllopoulos, Spiros

    1985-01-01

    This Working Paper Series entry represents the abstracts and visuals associated with presentations delivered by six USL NASA/RECON research team members at the above named conference. The presentations highlight various aspects of NASA contract activities pursued by the participants as they relate to individual research projects. The titles of the six presentations are as follows: (1) The Specification and Design of a Distributed Workstation; (2) An Innovative, Multidisciplinary Educational Program in Interactive Information Storage and Retrieval; (3) Critical Comparative Analysis of the Major Commercial IS and R Systems; (4) Design Criteria for a PC-Based Common User Interface to Remote Information Systems; (5) The Design of an Object-Oriented Graphics Interface; and (6) Knowledge-Based Information Retrieval: Techniques and Applications.

  18. Campaign datasets for ARM Airborne Carbon Measurements (ARM-ACME-V)

    SciTech Connect

    Biraud,Sebastien; Mei,Fan; Flynn,Connor; Hubbe,John; Long,Chuck; Matthews,Alyssa; Pekour,Mikhail; Sedlacek,Arthur; Springston,Stephen; Tomlinson,Jason; Chand,Duli

    2016-03-15

    Atmospheric temperatures are warming faster in the Arctic than predicted by climate models. The impact of this warming on permafrost degradation is not well understood, but it is projected to increase carbon decomposition and greenhouse gas production (CO2 and/or CH4) by arctic ecosystems. Airborne observations of atmospheric trace gases, aerosols, and cloud properties at the North Slope of Alaska are improving our understanding of global climate, with the goal of reducing the uncertainty in global and regional climate simulations and projections.

  19. Simulator Sickness Occurrences in the 2E6 Air Combat Maneuvering Simulator (ACMS).

    DTIC Science & Technology

    1981-02-01

    to consider in eval- uating the occurrence of simulator sickness in the SAAC. The Advanced Simulator for Pilot Training ( ASPT ) located at Williams AFB...uses the sane type of visual display as the Luke AFB SAAC. During on-site discussions with ASPT personnel, experiences of trainees in the ASPT were...reported as similar to those expe- * rienced in the SAAC. Although incidence rates for the ASPT were 4, not available, a tape of one subject’s

  20. Assessing the aerosol direct and first indirect effects using ACM/GCM simulation results

    NASA Astrophysics Data System (ADS)

    Huang, H.; Gu, Y.; Xue, Y.; Lu, C. H.

    2016-12-01

    Atmospheric aerosols have been found to play an important role in global climate change but there are still large uncertainty in evaluating its role in the climate system. The aerosols generally affect global and regional climate through the scattering and the absorption of solar radiation (direct effect) and through their influences on cloud particle, number and sizes (first indirect effect). The indirect effect will further affects cloud water content, cloud top albedo and surface precipitations. In this study, we investigate the global climatic effect of aerosols using a coupled NCEP Global Forecast System (GFS) and a land surface model (SSiB2) The OPAC (Optical Properties of Aerosols and Clouds) database is used for aerosol effect. The OPAC data provides the optical properties (i.e., the extinction, scattering and absorption coefficient, single-scattering albedo, asymmetry factor and phase function) of ten types of aerosols under various relative humidity conditions for investigating the global direct and first indirect effects of dust aerosols. For indirect forcings due to liquid water, we follow the approach presented by Jiang et al (2011), in which a parameterization of cloud effective radius was calculated to describe its variance with convective strength and aerosol concentration. Since the oceans also play an important role on aerosol climatic effect, we also design a set of simulations using a coupled atmosphere/ocean model (CFS) to evaluate the sensitivity of aerosol effect with two-way atmosphere-ocean interactions.

  1. The atmospheric hydrologic cycle in the ACME v0.3 model

    NASA Astrophysics Data System (ADS)

    Terai, Christopher R.; Caldwell, Peter M.; Klein, Stephen A.; Tang, Qi; Branstetter, Marcia L.

    2017-07-01

    We examine the global water cycle characteristics in the Accelerated Climate Modeling for Energy v0.3 model (a close relative to version 5.3 of the Community Atmosphere Model) in atmosphere-only simulations spanning the years 1980-2005. We evaluate the simulations using a broad range of observational and reanalysis datasets, examine how the simulations change when the horizontal resolution is increased from 1° to 0.25° , and compare the simulations against models participating in the the Atmosphere Model Intercomparison Project of the 5th Coupled Model Intercomparison Project (CMIP5). Particular effort has been made to evaluate the model using the best available observational estimates and verifying model biases with additional datasets when differences are known to exist among the observations. Regardless of resolution, the model exhibits several biases: global-mean precipitation, evaporation, and precipitable water are too high, light precipitation occurs too frequently, and the atmospheric residence time of water is too short. Many of these biases are shared by the multi-model mean climate of models participating in CMIP5. The reasons behind regional biases in precipitation are discussed by examining how different fields, such as local evaporation and transport of water vapor, contribute to the bias. Although increasing the horizontal resolution does not drastically change the water cycle, it does lead to a few differences: an increase in global mean precipitation rate, an increase in the fraction of total precipitation that falls over land, more frequent heavy precipitation (>30 mm day^{-1} ), and a decrease in precipitable water. One of the most notable changes is the shift of precipitation produced by the convective parameterization to that produced by the large-scale microphysics parameterization. We analyze how changes in moisture and circulation with resolution contribute to this shift in the precipitation partitioning. Because changing horizontal resolution requires some re-tuning, the effect of that tuning was evaluated by performing an additional simulation at 1° but using the tunings from the 0.25° simulation. The evaluation shows that the more frequent heavy precipitation, the decrease in precipitable water, and the shift from convective to large-scale precipitation are predominantly due to resolution changes, while tuning changes have a major influence on the global mean precipitation and the land/ocean partitioning of precipitation.

  2. Device 2E6 (ACMS) Air Combat Maneuvering Simulator Instructor Console Review.

    DTIC Science & Technology

    1983-12-01

    reflects this manning concept. The use of the MOs has resulted in the technician operator providing only "on call " maintenance support except for some relief...disagreement on some usage of color. The specification calls for amber to be used for color coding of instructor input actions while the MIL STD (and Navy...aircrw station design practice) calls for its use in alerting the operator to marginal conditions, the so- called "CAUTION" - 44 - bA NAVTRAEQUIPCEN 82-M

  3. Proposed Expansion of Acme Landfill Operations, Contra Costa, County, California. Volume 1.

    DTIC Science & Technology

    1983-06-01

    for example, plastic beverage bottles, cardboard, wood, yardwastes, textiles , rubber, and leather. In addition to traditional activities, a central...a 6000-foot-long dredged channel. The 200-acre parcel is crossed with a number of drainage ditches, constructed by the Contra Costa Mosquito ...incoming flow at the high tide. It is the only point of discharge for flood water and is maintained by the Contra Costa Mosquito Abatement District

  4. Hydrothermal Processes

    NASA Astrophysics Data System (ADS)

    German, C. R.; von Damm, K. L.

    2003-12-01

    What is Hydrothermal Circulation?Hydrothermal circulation occurs when seawater percolates downward through fractured ocean crust along the volcanic mid-ocean ridge (MOR) system. The seawater is first heated and then undergoes chemical modification through reaction with the host rock as it continues downward, reaching maximum temperatures that can exceed 400 °C. At these temperatures the fluids become extremely buoyant and rise rapidly back to the seafloor where they are expelled into the overlying water column. Seafloor hydrothermal circulation plays a significant role in the cycling of energy and mass between the solid earth and the oceans; the first identification of submarine hydrothermal venting and their accompanying chemosynthetically based communities in the late 1970s remains one of the most exciting discoveries in modern science. The existence of some form of hydrothermal circulation had been predicted almost as soon as the significance of ridges themselves was first recognized, with the emergence of plate tectonic theory. Magma wells up from the Earth's interior along "spreading centers" or "MORs" to produce fresh ocean crust at a rate of ˜20 km3 yr-1, forming new seafloor at a rate of ˜3.3 km2 yr-1 (Parsons, 1981; White et al., 1992). The young oceanic lithosphere formed in this way cools as it moves away from the ridge crest. Although much of this cooling occurs by upward conduction of heat through the lithosphere, early heat-flow studies quickly established that a significant proportion of the total heat flux must also occur via some additional convective process (Figure 1), i.e., through circulation of cold seawater within the upper ocean crust (Anderson and Silbeck, 1981). (2K)Figure 1. Oceanic heat flow versus age of ocean crust. Data from the Pacific, Atlantic, and Indian oceans, averaged over 2 Ma intervals (circles) depart from the theoretical cooling curve (solid line) indicating convective cooling of young ocean crust by circulating seawater

  5. A Low Temperature, Solution-Processed Poly(4-vinylphenol), YO(x) Nanoparticle Composite/Polysilazane Bi-Layer Gate Insulator for ZnO Thin Film Transistor.

    PubMed

    Shin, Hyeonwoo; Kang, Chan-Mo; Chae, Hyunsik; Kim, Hyun-Gwan; Baek, Kyu-Ha; Choi, Hyoung Jin; Park, Man-Young; Do, Lee-Mi; Lee, Changhee

    2016-03-01

    Low temperature, solution-processed metal oxide thin film transistors (MEOTFTs) have been widely investigated for application in low-cost, transparent, and flexible electronics. To enlarge the application area, solution-processed gate insulators (GI) have been investigated in recent years. We investigated the effects of the organic/inorganic bi-layer GI to ZnO thin film transistors (TFTs). PVP, YO(x) nanoparticle composite, and polysilazane bi-layer showed low leakage current (-10(-8) A/cm2 in 2 MV), which are applicable in low temperature processed MEOTFTs. Polysilazane was used as an interlayer between ZnO and PVP, YO(x) nanoparticle composite as a good charge transport interface with ZnO. By applying the PVP, YO(x), nanoparticle composite/polysilazane bi-layer structure to ZnO TFTs, we successfully suppressed the off current (I(off)) to -10(-11) and fabricated good MEOTFTs in 180 degrees C.

  6. Reduced water vapor transmission rates of low-temperature solution-processed metal oxide barrier films via ultraviolet annealing

    NASA Astrophysics Data System (ADS)

    Park, Seonuk; Jeong, Yong Jin; Baek, Yonghwa; Kim, Lae Ho; Jang, Jin Hyuk; Kim, Yebyeol; An, Tae Kyu; Nam, Sooji; Kim, Se Hyun; Jang, Jaeyoung; Park, Chan Eon

    2017-08-01

    Here, we report the fabrication of low-temperature sol-gel-derived aluminum oxide (AlOx) films via ultraviolet (UV) annealing and the investigation of their water vapor blocking properties by measuring the water vapor transmission rates (WVTRs). The UV annealing process induced the formation of a dense metal-oxygen-metal bond (Al-O-Al structure) at low temperatures (<200 °C) that are compatible with commercial plastic substrates. The density of the UV-annealed AlOx thin film at 180 °C was comparable to that of AlOx thin films that have been thermally annealed at 350 °C. Furthermore, the UV-annealed AlOx thin films exhibited a high optical transparency in the visible region (>99%) and good electrical insulating properties (∼10-7 A/cm2 at 2 MV/cm). Finally, we confirmed that a dense AlOx thin film was successfully deposited onto the plastic substrate via UV annealing at low temperatures, leading to a substantial reduction in the WVTRs. The Ca corrosion test was used to measure the WVTRs of AlOx thin films deposited onto polyethylene naphthalate or polyimide substrates, determined to be 0.0095 g m-2 day-1 (25 °C, 50% relative humidity) and 0.26 g m-2 day-1, respectively.

  7. Acemetacin cocrystals and salts: structure solution from powder X-ray data and form selection of the piperazine salt.

    PubMed

    Sanphui, Palash; Bolla, Geetha; Nangia, Ashwini; Chernyshev, Vladimir

    2014-03-01

    Acemetacin (ACM) is a non-steroidal anti-inflammatory drug (NSAID), which causes reduced gastric damage compared with indomethacin. However, acemetacin has a tendency to form a less soluble hydrate in the aqueous medium. We noted difficulties in the preparation of cocrystals and salts of acemetacin by mechanochemical methods, because this drug tends to form a hydrate during any kind of solution-based processing. With the objective to discover a solid form of acemetacin that is stable in the aqueous medium, binary adducts were prepared by the melt method to avoid hydration. The coformers/salt formers reported are pyridine carboxamides [nicotinamide (NAM), isonicotinamide (INA), and picolinamide (PAM)], caprolactam (CPR), p-aminobenzoic acid (PABA), and piperazine (PPZ). The structures of an ACM-INA cocrystal and a binary adduct ACM-PABA were solved using single-crystal X-ray diffraction. Other ACM cocrystals, ACM-PAM and ACM-CPR, and the piperazine salt ACM-PPZ were solved from high-resolution powder X-ray diffraction data. The ACM-INA cocrystal is sustained by the acid⋯pyridine heterosynthon and N-H⋯O catemer hydrogen bonds involving the amide group. The acid⋯amide heterosynthon is present in the ACM-PAM cocrystal, while ACM-CPR contains carboxamide dimers of caprolactam along with acid-carbonyl (ACM) hydrogen bonds. The cocrystals ACM-INA, ACM-PAM and ACM-CPR are three-dimensional isostructural. The carboxyl⋯carboxyl synthon in ACM-PABA posed difficulty in assigning the position of the H atom, which may indicate proton disorder. In terms of stability, the salts were found to be relatively stable in pH 7 buffer medium over 24 h, but the cocrystals dissociated to give ACM hydrate during the same time period. The ACM-PPZ salt and ACM-nicotinamide cocrystal dissolve five times faster than the stable hydrate form, whereas the ACM-PABA adduct has 2.5 times faster dissolution rate. The pharmaceutically acceptable piperazine salt of acemetacin exhibits superior

  8. Electrotechnologies to process foods

    USDA-ARS?s Scientific Manuscript database

    Electrical energy is being used to process foods. In conventional food processing plants, electricity drives mechanical devices and controls the degree of process. In recent years, several processing technologies are being developed to process foods directly with electricity. Electrotechnologies use...

  9. Enabling a Collaborative Problem-Solving Framework Through User Intent Modeling of the Analytic Process

    DTIC Science & Technology

    2009-08-01

    Nguyen, Eugene Santos Jr., Russell Jacob, and Nathan Smith. In Proceedings of 2008 IEEE/WIC/ACM International Conference on Web Intelligence. Sydney...of Social Cognition. • McDoland, D. W., and Ackerman , M. S. 2000. Expertise Recommender: A plexible recom- mendation system and architecture. In

  10. Optimization of a Solution-Processed SiO2 Gate Insulator by Plasma Treatment for Zinc Oxide Thin Film Transistors.

    PubMed

    Jeong, Yesul; Pearson, Christopher; Kim, Hyun-Gwan; Park, Man-Young; Kim, Hongdoo; Do, Lee-Mi; Petty, Michael C

    2016-01-27

    We report on the optimization of the plasma treatment conditions for a solution-processed silicon dioxide gate insulator for application in zinc oxide thin film transistors (TFTs). The SiO2 layer was formed by spin coating a perhydropolysilazane (PHPS) precursor. This thin film was subsequently thermally annealed, followed by exposure to an oxygen plasma, to form an insulating (leakage current density of ∼10(-7) A/cm(2)) SiO2 layer. Optimized ZnO TFTs (40 W plasma treatment of the gate insulator for 10 s) possessed a carrier mobility of 3.2 cm(2)/(V s), an on/off ratio of ∼10(7), a threshold voltage of -1.3 V, and a subthreshold swing of 0.2 V/decade. In addition, long-term exposure (150 min) of the pre-annealed PHPS to the oxygen plasma enabled the maximum processing temperature to be reduced from 180 to 150 °C. The resulting ZnO TFT exhibited a carrier mobility of 1.3 cm(2)/(V s) and on/off ratio of ∼10(7).

  11. High quality mid-wavelength infrared InAs/GaSb superlattices by exploring the optimum molecular beam epitaxy growth process

    NASA Astrophysics Data System (ADS)

    Xu, Zhicheng; Chen, Jianxin; Wang, Fangfang; Zhou, Yi; Jin, Chuan; Xu, Qingqing; He, Li

    2014-11-01

    In this paper we report on the growth of mid-wavelength infrared superlattice materials by molecular beam epitaxy. We focused on the effects of process parameters, such as arsenic beam equivalent pressure and shutter sequences, on the key material properties, such as the lattice mismatch and the surface morphology. Though a smaller As beam equivalent pressure helps to reduce the lattice mismatch between the superlattice and the GaSb substrate, the As beam equivalent pressure itself has a lower limit below which the material's surface morphology will degrade. To achieve fully lattice-matched superlattice materials, a novel shutter sequence in the growth process was designed. With well-designed interface structures, a high quality P-I-N superlattice mid-infrared detector structure was realized. At 77 K the dark current density at -50 mV bias was 2.4 × 10-8 A/cm2 and the resistance-area product (RA) at maximum (-50 mV bias) was 2.4 × 106 Ω cm2, and the peak detectivity was then calculated to be 9.0 × 1012 cm Hz1/2/W. The background limited infrared photodetector (BLIP) level can be achieved at a temperature of 113 K.

  12. Hydrocarbon Processing`s process design and optimization `96

    SciTech Connect

    1996-06-01

    This paper compiles information on hydrocarbon processes, describing the application, objective, economics, commercial installations, and licensor. Processes include: alkylation, ammonia, catalytic reformer, crude fractionator, crude unit, vacuum unit, dehydration, delayed coker, distillation, ethylene furnace, FCCU, polymerization, gas sweetening, hydrocracking, hydrogen, hydrotreating (naphtha, distillate, and resid desulfurization), natural gas processing, olefins, polyethylene terephthalate, refinery, styrene, sulfur recovery, and VCM furnace.

  13. Extensible packet processing architecture

    DOEpatents

    Robertson, Perry J.; Hamlet, Jason R.; Pierson, Lyndon G.; Olsberg, Ronald R.; Chun, Guy D.

    2013-08-20

    A technique for distributed packet processing includes sequentially passing packets associated with packet flows between a plurality of processing engines along a flow through data bus linking the plurality of processing engines in series. At least one packet within a given packet flow is marked by a given processing engine to signify by the given processing engine to the other processing engines that the given processing engine has claimed the given packet flow for processing. A processing function is applied to each of the packet flows within the processing engines and the processed packets are output on a time-shared, arbitered data bus coupled to the plurality of processing engines.

  14. Salicylic acid degradation by advanced oxidation processes. Coupling of solar photoelectro-Fenton and solar heterogeneous photocatalysis.

    PubMed

    Garza-Campos, Benjamin; Brillas, Enric; Hernández-Ramírez, Aracely; El-Ghenymy, Abdellatif; Guzmán-Mar, Jorge Luis; Ruiz-Ruiz, Edgar J

    2016-12-05

    A 3.0 L solar flow plant with a Pt/air-diffusion (anode/cathode) cell, a solar photoreactor and a photocatalytic photoreactor filled with TiO2-coated glass spheres has been utilized to couple solar photoelectro-Fenton (SPEF) and solar heterogeneous photocatalysis (SPC) for treating a 165mgL(-1) salicylic acid solution of pH 3.0. Organics were destroyed by OH radicals formed on the TiO2 photocatalyst and at the Pt anode during water oxidation and in the bulk from Fenton's reaction between added Fe(2+) and cathodically generated H2O2, along with the photolytic action of sunlight. Poor salicylic acid removal and mineralization were attained using SPC, anodic oxidation with electrogenerated H2O2 (AO-H2O2) and coupled AO-H2O2-SPC. The electro-Fenton process accelerated the substrate decay, but with low mineralization by the formation of byproducts that are hardly destroyed by OH. The mineralization was strongly increased by SPEF due to the photolysis of products by sunlight, being enhanced by coupled SPEF-SPC due to the additional oxidation by OH at the TiO2 surface. The effect of current density on the performance of both processes was examined. The most potent SPEF-SPC process at 150mAcm(-2) yielded 87% mineralization and 13% current efficiency after consuming 6.0AhL(-1). Maleic, fumaric and oxalic acids detected as final carboxylic acids were completely removed by SPEF and SPEF-SPC.

  15. Physicochemical treatment processes

    SciTech Connect

    Grasso, D.; Morico, K.; Kock, N.; Flood, K.; Armstrong, R. ); Walters, R. ); Ellis, G. ); Chin, Yuping )

    1990-06-01

    This article discussed work done and accomplishments made in various methods and processes for physicochemical wastewater treatment. Processes discussed include general, precipitation, coagulation/flocculation, sedimentation/flotation, filtration, adsorption, ion exchange, membrane processes, mass transfer processes, phtotlytic processes, and oxidation/reduction processes.

  16. Coal liquefaction process with enhanced process solvent

    DOEpatents

    Givens, Edwin N.; Kang, Dohee

    1984-01-01

    In an improved coal liquefaction process, including a critical solvent deashing stage, high value product recovery is improved and enhanced process-derived solvent is provided by recycling second separator underflow in the critical solvent deashing stage to the coal slurry mix, for inclusion in the process solvent pool.

  17. Anatomical connectivity mapping: a new tool to assess brain disconnection in Alzheimer's disease.

    PubMed

    Bozzali, Marco; Parker, Geoffrey J M; Serra, Laura; Embleton, Karl; Gili, Tommaso; Perri, Roberta; Caltagirone, Carlo; Cercignani, Mara

    2011-02-01

    Previous studies suggest that the clinical manifestations of Alzheimer's disease (AD) are not only associated with regional gray matter damage but also with abnormal functional integration of different brain regions by disconnection mechanisms. A measure of anatomical connectivity (anatomical connectivity mapping or ACM) can be obtained by initiating diffusion tractography streamlines from all parenchymal voxels and then counting the number of streamlines passing through each voxel of the brain. In order to assess the potential of this parameter for the study of disconnection in AD, we computed it in a group of patients with AD (N=9), in 16 patients with amnestic mild cognitive impairment (a-MCI, which is considered the prodromal stage of AD) and in 12 healthy volunteers. All subjects had an MRI scan at 3T, and diffusion MRI data were analyzed to obtain fractional anisotropy (FA) and ACM. Two types of ACM maps, absolute count (ac-ACM) and normalized by brain size count (nc-ACM), were obtained. No between group differences in FA surviving correction for multiple comparison were found, while areas of both decreased (in the supramarginal gyrus) and increased (in the putamen) ACM were found in patients with AD. Similar results were obtained with ac-ACM and nc-ACM. ACM of the supramarginal gyrus was strongly associated with measures of short-term memory in healthy subjects. This study shows that ACM provides information that is complementary to that offered by FA and appears to be more sensitive than FA to brain changes in patients with AD. The increased ACM in the putamen was unexpected. Given the nature of ACM, an increase of this parameter may reflect a change in any of the areas connected to it. One intriguing possibility is that this increase of ACM in AD patients might reflect processes of brain plasticity driven by cholinesterase inhibitors.

  18. Dip-coated multi-core (Bi,Pb) 2Sr 2Ca 2Cu 3O x tape process - an alternative way of fabricating multi-core (Bi,Pb) 2Sr 2Ca 2Cu 3O x tape conductors

    NASA Astrophysics Data System (ADS)

    Sung, Y. S.; Kumakura, H.; Togano, K.

    2000-04-01

    The dip-coating-then-stacking (DIS) process, which is simpler and easier than the oxide-powder-in-tube (OPIT) process, was developed to fabricate multi-core (Bi,Pb) 2Sr 2Ca 2Cu 3O x conductors. In the DIS process, multi-core tapes were prepared by stacking several layers of single side dip-coated Ag strips then wrapping them with Ag foil. After burning at 500°C to remove organic materials, tape samples were rolled to increase the packing density of oxide core, then were heat-treated twice at 838°C in air with an intermediate pressing. There was no bubbling problem throughout the heat treatment and the interface between oxide core and Ag was very smooth. By the DIS process, transport critical current ( Ic) ∼73 A and transport critical current density ( Jc) ∼17 600 A/cm 2 at 77 K, 0 T were so far obtained. Considering the easiness and simplicity of the DIS process relative to OPIT with reasonably high Ic and Jc values so far obtained, it appears that the DIS process can be applied as an alternative way to OPIT for fabricating multi-core (Bi,Pb) 2Sr 2Ca 2Cu 3O x tape conductors.

  19. A Distributed Processing Approach to Word Processing/Data Processing.

    ERIC Educational Resources Information Center

    Adams, Robert D.; Magnuson, Jerry R.

    1980-01-01

    A word processing system developed at the University of Kansas is described. A cost-benefit analysis of the system v standard typewriter, mag-card, and other advanced word processing systems is developed. Intangible benefits such as worker satisfaction and reduced training and editing needs are discussed, and possible uses outlined. (MSE)

  20. Application of excitation and emission matrix fluorescence (EEM) and UV-vis absorption to monitor the characteristics of Alizarin Red S (ARS) during electro-Fenton degradation process.

    PubMed

    Lai, Bo; Zhou, Yuexi; Wang, Juling; Yang, Zhishan; Chen, Zhiqiang

    2013-11-01

    Oxidative degradation of Alizarin Red S (ARS) in aqueous solutions by using electro-Fenton was studied. At first, effect of operating parameters such as current density, aeration rate and initial pH on the degradation of ARS were studied by using UV-vis spectrum, respectively. Then, under the optimal operating conditions (current density: 10.0mAcm(-2), aeration rate: 1000mLmin(-1), initial pH: 2.8), the identification of degradation products of ARS was carried out by using GC-MS and HPLC, meanwhile its degradation pathway was proposed according to the intermediates. Considering the location, intensity and intensity ratio of fluorescence center peak of the ARS in aqueous solution, a convenient and quick monitoring method by using excitation-emission matrix fluorescence spectrum technology was developed to monitor the degradation degree of ARS through electro-Fenton process. Furthermore, it is suggested that the developed method would be promising for the quick analysis and evaluation of the degradation degree of the pollutants with π-conjugated system. Copyright © 2013 Elsevier Ltd. All rights reserved.

  1. Study on the formation of self-assembled monolayers on sol-gel processed hafnium oxide as dielectric layers.

    PubMed

    Ting, Guy G; Acton, Orb; Ma, Hong; Ka, Jae Won; Jen, Alex K-Y

    2009-02-17

    High dielectric constant (k) metal oxides such as hafnium oxide (HfO2) have gained significant interest due to their applications in microelectronics. In order to study and control the surface properties of hafnium oxide, self-assembled monolayers (SAMs) of four different long aliphatic molecules with binding groups of phosphonic acid, carboxylic acid, and catechol were formed and characterized. Surface modification was performed to improve the interface between metal oxide and top deposited materials as well as to create suitable dielectric properties, that is, leakage current and capacitance densities, which are important in organic thin film transistors. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy, contact angle goniometry, atomic force microscopy (AFM), and simple metal-HfO2-SAM-metal devices were used to characterize the surfaces before and after SAM modification on sol-gel processed hafnium oxide. The alkylphosphonic acid provided the best monolayer formation on sol-gel processed hafnium oxide to generate a well-packed, ultrathin dielectric exhibiting a low leakage current density of 2x10(-8) A/cm2 at an applied voltage of -2.0 V and high capacitance density of 0.55 microF/cm2 at 10 kHz. Dialkylcatechol showed similar characteristics and the potential for using the catechol SAMs to modify HfO2 surfaces. In addition, the integration of this alkylphosphonic acid SAM/hafnium oxide hybrid dielectric into pentacene-based thin film transistors yields low-voltage operation within 1.5 V and improved performance over bare hafnium oxide.

  2. SAR processing using SHARC signal processing systems

    NASA Astrophysics Data System (ADS)

    Huxtable, Barton D.; Jackson, Christopher R.; Skaron, Steve A.

    1998-09-01

    Synthetic aperture radar (SAR) is uniquely suited to help solve the Search and Rescue problem since it can be utilized either day or night and through both dense fog or thick cloud cover. Other papers in this session, and in this session in 1997, describe the various SAR image processing algorithms that are being developed and evaluated within the Search and Rescue Program. All of these approaches to using SAR data require substantial amounts of digital signal processing: for the SAR image formation, and possibly for the subsequent image processing. In recognition of the demanding processing that will be required for an operational Search and Rescue Data Processing System (SARDPS), NASA/Goddard Space Flight Center and NASA/Stennis Space Center are conducting a technology demonstration utilizing SHARC multi-chip modules from Boeing to perform SAR image formation processing.

  3. Desalination processes and performance

    SciTech Connect

    Summers, L. J.

    1995-06-01

    Different desalination processes are evaluated for feed, capacity, performance, energy requirements, and cost. These include distillation, reverse osmosis, or electrodialysis. Detailed information is given on distillation processes and membrane processes.

  4. Special parallel processing workshop

    SciTech Connect

    1994-12-01

    This report contains viewgraphs from the Special Parallel Processing Workshop. These viewgraphs deal with topics such as parallel processing performance, message passing, queue structure, and other basic concept detailing with parallel processing.

  5. Preparation and Thermodynamics of High Critical Transition Temperature Superconducting Films Growth by Liquid-Gas Process

    NASA Astrophysics Data System (ADS)

    Chou, Hsiung

    The in situ Tl-base superconducting films have been grown successfully on MgO and SrTiO_3 < 100> substrates by Liquid-Gas-Solidification (LGS) process. The loss of Tl during growth process can be nearly eliminated by a proper geometry design of the LGS set up. there is no post anneal for forming the right structure or compensation of Tl applied after the initial deposition. The Tl-base films grown on MgO < 100> exhibits an oriented structure with c-axis perpendicular to the surface of substrates. X-ray diffraction patterns reveal a coexistence of multi-phases in the films. The morphology of films shows flat and uniform domains of 0.5 times 1 mm^2. It exhibits a resistant transition onset of 117K and zero resistance at 103K. In the films grown on SrTiO _3 < 100> substrate, Ca-O precipitations on the edge of the film layer are observed. Upon a post anneal process, the Ca -O precipitates disappear resulted in an enhanced transport critical current density of 10^{-5 } A/cm^2. In forming the oxide film in LGS processing, oxygen is absorbed and diffuses into the liquid alloy reaching the liquid-substrate interface to form the oxide. The nucleation and growth of the films is a matter of the thermodynamic and the kinetic behavior of oxygen in the liquid precursor. A modified coulometric titration method is introduced to understand this behavior and to measure the activity, diffusivity and solubility of oxygen in the liquid high T_ {rm c} superconducting precursor alloys, rm Yb_1Ba_2Cu_3 , Ag-Yb_1Ba_2 Cu_3 and rm Tl_1Ba_2Ca_2Cu_3. In all alloy systems investigated, the formation energy of oxygen dissolved into the liquid alloys is relatively low ({~}{-}255 kJ/g-atom) which is attributed to the present of rare earth elements of Ba, Ca and Yb. The high affinity of oxygen with these elements results in a limited oxygen solubility (10^{-4} molar fraction), however, the diffusion coefficients of oxygen in the liquid alloys are high of the order of 10^{ -4} cm^2/sec. These

  6. Scalable, Economical Fabrication Processes for Ultra-Compact Warm-White LEDs

    SciTech Connect

    Lowes, Ted

    2016-01-31

    Conventional warm-white LED component fabrication consists of a large number of sequential steps which are required to incorporate electrical, mechanical, and optical functionality into the component. Each of these steps presents cost and yield challenges which multiply throughout the entire process. Although there has been significant progress in LED fabrication over the last decade, significant advances are needed to enable further reductions in cost per lumen while not sacrificing efficacy or color quality. Cree conducted a focused 18-month program to develop a new low-cost, high-efficiency light emitting diode (LED) architecture enabled by novel large-area parallel processing technologies, reduced number of fabrication steps, and minimized raw materials use. This new scheme is expected to enable ultra-compact LED components exhibiting simultaneously high efficacy and high color quality. By the end of the program, Cree fabricated warm-white LEDs with a room-temperature “instant on” efficacy of >135 lm/W at ~3500K and 90 CRI (when driven at the DOE baseline current density of 35 A/cm2). Cree modified the conventional LED fabrication process flow in a manner that is expected to translate into simultaneously high throughput and yield for ultra-compact packages. Building on its deep expertise in LED wafer fabrication, Cree developed these ultra-compact LEDs to have no compromises in color quality or efficacy compared to their conventional counterparts. Despite their very small size, the LEDs will also be robustly electrically integrated into luminaire systems with the same attach yield as conventional packages. The versatility of the prototype high-efficacy LED architecture will likely benefit solid-state lighting (SSL) luminaire platforms ranging from bulbs to troffers. We anticipate that the prototype LEDs will particularly benefit luminaires with large numbers of distributed compact packages, such as linear and area luminaires (e.g. troffers). The fraction of

  7. Hyperspectral processing in graphical processing units

    NASA Astrophysics Data System (ADS)

    Winter, Michael E.; Winter, Edwin M.

    2011-06-01

    With the advent of the commercial 3D video card in the mid 1990s, we have seen an order of magnitude performance increase with each generation of new video cards. While these cards were designed primarily for visualization and video games, it became apparent after a short while that they could be used for scientific purposes. These Graphical Processing Units (GPUs) are rapidly being incorporated into data processing tasks usually reserved for general purpose computers. It has been found that many image processing problems scale well to modern GPU systems. We have implemented four popular hyperspectral processing algorithms (N-FINDR, linear unmixing, Principal Components, and the RX anomaly detection algorithm). These algorithms show an across the board speedup of at least a factor of 10, with some special cases showing extreme speedups of a hundred times or more.

  8. Thermochemical water decomposition processes

    NASA Technical Reports Server (NTRS)

    Chao, R. E.

    1974-01-01

    Thermochemical processes which lead to the production of hydrogen and oxygen from water without the consumption of any other material have a number of advantages when compared to other processes such as water electrolysis. It is possible to operate a sequence of chemical steps with net work requirements equal to zero at temperatures well below the temperature required for water dissociation in a single step. Various types of procedures are discussed, giving attention to halide processes, reverse Deacon processes, iron oxide and carbon oxide processes, and metal and alkali metal processes. Economical questions are also considered.

  9. Thermochemical water decomposition processes

    NASA Technical Reports Server (NTRS)

    Chao, R. E.

    1974-01-01

    Thermochemical processes which lead to the production of hydrogen and oxygen from water without the consumption of any other material have a number of advantages when compared to other processes such as water electrolysis. It is possible to operate a sequence of chemical steps with net work requirements equal to zero at temperatures well below the temperature required for water dissociation in a single step. Various types of procedures are discussed, giving attention to halide processes, reverse Deacon processes, iron oxide and carbon oxide processes, and metal and alkali metal processes. Economical questions are also considered.

  10. Digital image processing.

    PubMed

    Seeram, Euclid

    2004-01-01

    Digital image processing is now commonplace in radiology, nuclear medicine and sonography. This article outlines underlying principles and concepts of digital image processing. After completing this article, readers should be able to: List the limitations of film-based imaging. Identify major components of a digital imaging system. Describe the history and application areas of digital image processing. Discuss image representation and the fundamentals of digital image processing. Outline digital image processing techniques and processing operations used in selected imaging modalities. Explain the basic concepts and visualization tools used in 3-D and virtual reality imaging. Recognize medical imaging informatics as a new area of specialization for radiologic technologists.

  11. Electrochemical synthesis of nickel-aluminium oxide system from metals obtained by ore processing

    NASA Astrophysics Data System (ADS)

    Korobochkin, V. V.; Usoltseva, N. V.; Shorokhov, K. G.; Popova, E. V.

    2015-11-01

    Separate and combined electrochemical oxidation of aluminium and nickel has been conducted by alternating current of industrial frequency. Concentration increase of electrolyte solution (sodium chloride) in the range from 3 to 25 wt. % and current density from 0.5 to 1.5 A/cm2 was found to result in the increasing metal oxidation rate, excluding aluminium oxidation which oxidation rate is independent of the electrolyte solution concentration. At the current density of 1.5 A/cm2 the products of separate oxidation of nickel and aluminium are nickel oxyhydroxides, nickel hydroxides and aluminium oxyhydroxide (boehmite), respectively. In addition to these compounds, the nickel-aluminium oxide hydrate is included in the products of nickel and aluminium co-oxidation. Its content grows with the increasing electrolyte solution concentration. Varying the concentration and current density within the limits indicated, the nickel-aluminium oxide system with nickel oxide content from 3 to 10 wt. % is produced.

  12. Acoustic signal processing toolbox for array processing

    NASA Astrophysics Data System (ADS)

    Pham, Tien; Whipps, Gene T.

    2003-08-01

    The US Army Research Laboratory (ARL) has developed an acoustic signal processing toolbox (ASPT) for acoustic sensor array processing. The intent of this document is to describe the toolbox and its uses. The ASPT is a GUI-based software that is developed and runs under MATLAB. The current version, ASPT 3.0, requires MATLAB 6.0 and above. ASPT contains a variety of narrowband (NB) and incoherent and coherent wideband (WB) direction-of-arrival (DOA) estimation and beamforming algorithms that have been researched and developed at ARL. Currently, ASPT contains 16 DOA and beamforming algorithms. It contains several different NB and WB versions of the MVDR, MUSIC and ESPRIT algorithms. In addition, there are a variety of pre-processing, simulation and analysis tools available in the toolbox. The user can perform simulation or real data analysis for all algorithms with user-defined signal model parameters and array geometries.

  13. GREENSCOPE: Sustainable Process Modeling

    EPA Science Inventory

    EPA researchers are responding to environmental problems by incorporating sustainability into process design and evaluation. EPA researchers are also developing a tool that allows users to assess modifications to existing and new chemical processes to determine whether changes in...

  14. Natural Language Processing.

    ERIC Educational Resources Information Center

    Chowdhury, Gobinda G.

    2003-01-01

    Discusses issues related to natural language processing, including theoretical developments; natural language understanding; tools and techniques; natural language text processing systems; abstracting; information extraction; information retrieval; interfaces; software; Internet, Web, and digital library applications; machine translation for…

  15. Test processing system (SEE)

    NASA Technical Reports Server (NTRS)

    Gaulene, P.

    1986-01-01

    The SEE data processing system, developed in 1985, manages and process test results. General information is provided on the SEE system: objectives, characteristics, basic principles, general organization, and operation. Full documentation is accessible by computer using the HELP SEE command.

  16. Process evaluation distributed system

    NASA Technical Reports Server (NTRS)

    Moffatt, Christopher L. (Inventor)

    2006-01-01

    The distributed system includes a database server, an administration module, a process evaluation module, and a data display module. The administration module is in communication with the database server for providing observation criteria information to the database server. The process evaluation module is in communication with the database server for obtaining the observation criteria information from the database server and collecting process data based on the observation criteria information. The process evaluation module utilizes a personal digital assistant (PDA). A data display module in communication with the database server, including a website for viewing collected process data in a desired metrics form, the data display module also for providing desired editing and modification of the collected process data. The connectivity established by the database server to the administration module, the process evaluation module, and the data display module, minimizes the requirement for manual input of the collected process data.

  17. News: Process intensification

    EPA Science Inventory

    Conservation of materials and energy is a major objective to the philosophy of sustainability. Where production processes can be intensified to assist these objectives, significant advances have been developed to assist conservation as well as cost. Process intensification (PI) h...

  18. Polyamines in tea processing.

    PubMed

    Palavan-Unsal, Narcin; Arisan, Elif Damla; Terzioglu, Salih

    2007-06-01

    The distribution of dietary polyamines, putrescine, spermidine and spermine, was determined during processing of Camellia sinensis. Black tea manufacture is carried by a series of processes on fresh tea leaves involving withering, rolling, fermentation, drying and sieving. The aim of this research was to determine the effect of tea processing on the polyamine content in relation with antioxidant enzymes, superoxide dismutase, lipid peroxidase and glutathione peroxidase. Before processing, the spermine content was much higher than the putrescine and spermidine content in green tea leaves. Spermine was significantly decreased during processing while the putrescine and spermine contents increased during withered and rolling and decreased in the following stages. The superoxide dismutase activity increased at the withering stage and declined during processing. The transcript level of the polyamine biosynthesis-responsible enzyme ornithine decarboxylase was reduced during each processing step. This study reveals the importance of protection of nutritional compounds that are essential for health during the manufacturing process.

  19. GREENSCOPE: Sustainable Process Modeling

    EPA Science Inventory

    EPA researchers are responding to environmental problems by incorporating sustainability into process design and evaluation. EPA researchers are also developing a tool that allows users to assess modifications to existing and new chemical processes to determine whether changes in...

  20. News: Process intensification

    EPA Science Inventory

    Conservation of materials and energy is a major objective to the philosophy of sustainability. Where production processes can be intensified to assist these objectives, significant advances have been developed to assist conservation as well as cost. Process intensification (PI) h...

  1. Spacelab Data Processing Facility

    NASA Technical Reports Server (NTRS)

    1983-01-01

    The capabilities of the Spacelab Data Processing Facility (SPDPF) are highlighted. The capturing, quality monitoring, processing, accounting, and forwarding of vital Spacelab data to various user facilities around the world are described.

  2. Probabilistic Declarative Process Mining

    NASA Astrophysics Data System (ADS)

    Bellodi, Elena; Riguzzi, Fabrizio; Lamma, Evelina

    The management of business processes is receiving much attention, since it can support significant efficiency improvements in organizations. One of the most interesting problems is the representation of process models in a language that allows to perform reasoning on it.

  3. Natural Language Processing.

    ERIC Educational Resources Information Center

    Chowdhury, Gobinda G.

    2003-01-01

    Discusses issues related to natural language processing, including theoretical developments; natural language understanding; tools and techniques; natural language text processing systems; abstracting; information extraction; information retrieval; interfaces; software; Internet, Web, and digital library applications; machine translation for…

  4. Infrared processing of foods

    USDA-ARS?s Scientific Manuscript database

    Infrared (IR) processing of foods has been gaining popularity over conventional processing in several unit operations, including drying, peeling, baking, roasting, blanching, pasteurization, sterilization, disinfection, disinfestation, cooking, and popping . It has shown advantages over conventional...

  5. Materials processing in space

    NASA Technical Reports Server (NTRS)

    1975-01-01

    The feasibility and possible advantages of processing materials in a nongravitational field are considered. Areas of investigation include biomedical applications, the processing of inorganic materials, and flight programs and funding.

  6. The requirements discovery process

    SciTech Connect

    Bahill, A.T.; Dean, F.F.

    1997-02-01

    Cost and schedule overruns are often caused by poor requirements that are produced by people who do not understand the requirement process. This paper provides a high-level overview of the requirements discovery process.

  7. Fuel gas conditioning process

    DOEpatents

    Lokhandwala, Kaaeid A.

    2000-01-01

    A process for conditioning natural gas containing C.sub.3+ hydrocarbons and/or acid gas, so that it can be used as combustion fuel to run gas-powered equipment, including compressors, in the gas field or the gas processing plant. Compared with prior art processes, the invention creates lesser quantities of low-pressure gas per unit volume of fuel gas produced. Optionally, the process can also produce an NGL product.

  8. MITRE Adaptive Processing Capability

    DTIC Science & Technology

    1994-06-01

    gathering, Funded Research and Development transfer, processing , and interpretation of Center (FFRDC) under the primary data are provided. A strong state-of...1988: Unisys Reston Technology Center, Reston, VA Dr. Bronez was a Member of the Technical Staff. He performed research on signal processing and... processing , mathematical research , and sensor array processing . He was Project Leader and Principal Investigator for projects in adaptive beamforming

  9. Digital image processing

    NASA Technical Reports Server (NTRS)

    Bernstein, R.; Ferneyhough, D. G., Jr.

    1975-01-01

    The Federal Systems Division of IBM has developed an image processing facility to experimentally process, view, and record digital image data. This facility has been used to support LANDSAT digital image processing investigations and advanced image processing research and development. A brief description of the facility is presented, some techniques that have been developed to correct the image data are discussed, and some results obtained by users of the facility are described.

  10. Metallurgical processing: A compilation

    NASA Technical Reports Server (NTRS)

    1973-01-01

    The items in this compilation, all relating to metallurgical processing, are presented in two sections. The first section includes processes which are general in scope and applicable to a variety of metals or alloys. The second describes the processes that concern specific metals and their alloys.

  11. Processes for metal extraction

    NASA Technical Reports Server (NTRS)

    Bowersox, David F.

    1992-01-01

    This report describes the processing of plutonium at Los Alamos National Laboratory (LANL), and operation illustrating concepts that may be applicable to the processing of lunar materials. The toxic nature of plutonium requires a highly closed system for processing lunar surface materials.

  12. Handbook of Petroleum Processing

    NASA Astrophysics Data System (ADS)

    Jones, David S. J.; Pujado, Peter P.

    This handbook describes and discusses the features that make up the petroleum refining industry. It begins with a description of the crude oils and their nature, and continues with the saleable products from the refining processes, with a review of the environmental impact. There is a complete overview of the processes that make up the refinery with a brief history of those processes.

  13. Current Duplicating Processes

    ERIC Educational Resources Information Center

    Groneman, Nancy

    1978-01-01

    While business instructors are still teaching spirit and stencil duplicating processes, most businesses now use copiers or offset printing processes. The article discusses offset and copier skills needed by office workers, pointing out that the processes being taught should be compatible with those used in business. (MF)

  14. Semisolid Metal Processing Consortium

    SciTech Connect

    Apelian,Diran

    2002-01-10

    Mathematical modeling and simulations of semisolid filling processes remains a critical issue in understanding and optimizing the process. Semisolid slurries are non-Newtonian materials that exhibit complex rheological behavior. There the way these slurries flow in cavities is very different from the way liquid in classical casting fills cavities. Actually filling in semisolid processing is often counter intuitive

  15. The Constitutional Amendment Process

    ERIC Educational Resources Information Center

    Chism, Kahlil

    2005-01-01

    This article discusses the constitutional amendment process. Although the process is not described in great detail, Article V of the United States Constitution allows for and provides instruction on amending the Constitution. While the amendment process currently consists of six steps, the Constitution is nevertheless quite difficult to change.…

  16. How yogurt is processed

    USDA-ARS?s Scientific Manuscript database

    This month’s Processing column on the theme of “How Is It Processed?” focuses on yogurt. Yogurt is known for its health-promoting properties. This column will provide a brief overview of the history of yogurt and the current market. It will also unveil both traditional and modern yogurt processing t...

  17. Comprehension Processes in Reading.

    ERIC Educational Resources Information Center

    Balota, D. A., Ed.; And Others

    Focusing on the process of reading comprehension, this book contains chapters on some central topics relevant to understanding the processes associated with comprehending text. The articles and their authors are as follows: (1) "Comprehension Processes: Introduction" (K. Rayner); (2) "The Role of Meaning in Word Recognition"…

  18. The Natural Learning Process

    ERIC Educational Resources Information Center

    Criss, Ellen

    2008-01-01

    Teacher-educator and researcher Daniel L. Kohut suggests in "Musical Performance: Learning Theory and Pedagogy" that there are many problems that result from the way music teachers often teach. Most teachers focus on the process, not the goal. The Natural Learning Process that Kohut advocates is the same process that young children use when they…

  19. The Constitutional Amendment Process

    ERIC Educational Resources Information Center

    Chism, Kahlil

    2005-01-01

    This article discusses the constitutional amendment process. Although the process is not described in great detail, Article V of the United States Constitution allows for and provides instruction on amending the Constitution. While the amendment process currently consists of six steps, the Constitution is nevertheless quite difficult to change.…

  20. Image-Processing Educator

    NASA Technical Reports Server (NTRS)

    Gunther, F. J.

    1986-01-01

    Apple Image-Processing Educator (AIPE) explores ability of microcomputers to provide personalized computer-assisted instruction (CAI) in digital image processing of remotely sensed images. AIPE is "proof-of-concept" system, not polished production system. User-friendly prompts provide access to explanations of common features of digital image processing and of sample programs that implement these features.

  1. Change Processes in Organization.

    ERIC Educational Resources Information Center

    1998

    This document contains four papers from a symposium on change processes in organizations. "Mid-stream Corrections: Decisions Leaders Make during Organizational Change Processes" (David W. Frantz) analyzes three organizational leaders to determine whether and how they take corrective actions or adapt their decision-making processes when…

  2. Image processing in astronomy

    NASA Astrophysics Data System (ADS)

    Berry, Richard

    1994-04-01

    Today's personal computers are more powerful than the mainframes that processed images during the early days of space exploration. We have entered an age in which anyone can do image processing. Topics covering the following aspects of image processing are discussed: digital-imaging basics, image calibration, image analysis, scaling, spatial enhancements, and compositing.

  3. How tofu is processed

    USDA-ARS?s Scientific Manuscript database

    This month’s Processing column will continue the theme of “How Is It Processed?” The column will focus on tofu, which is sometimes called “the cheese of Asia.” It is a nutritious, protein-rich bean curd made by coagulating soy milk. There are many different types of tofu, and they are processed in a...

  4. Chemical Process Synthesis.

    ERIC Educational Resources Information Center

    Siirola, J. J.

    1982-01-01

    Process synthesis is the specification of chemical and physical operations and the selection and interconnection of equipment to implement these operations to effect desired chemical processing transformations. Optimization and evolutionary and systematic generation process synthesis approaches are described. (Author/SK)

  5. The Natural Learning Process

    ERIC Educational Resources Information Center

    Criss, Ellen

    2008-01-01

    Teacher-educator and researcher Daniel L. Kohut suggests in "Musical Performance: Learning Theory and Pedagogy" that there are many problems that result from the way music teachers often teach. Most teachers focus on the process, not the goal. The Natural Learning Process that Kohut advocates is the same process that young children use when they…

  6. Change Processes in Organization.

    ERIC Educational Resources Information Center

    1998

    This document contains four papers from a symposium on change processes in organizations. "Mid-stream Corrections: Decisions Leaders Make during Organizational Change Processes" (David W. Frantz) analyzes three organizational leaders to determine whether and how they take corrective actions or adapt their decision-making processes when…

  7. Teaching Process Design through Integrated Process Synthesis

    ERIC Educational Resources Information Center

    Metzger, Matthew J.; Glasser, Benjamin J.; Patel, Bilal; Hildebrandt, Diane; Glasser, David

    2012-01-01

    The design course is an integral part of chemical engineering education. A novel approach to the design course was recently introduced at the University of the Witwatersrand, Johannesburg, South Africa. The course aimed to introduce students to systematic tools and techniques for setting and evaluating performance targets for processes, as well as…

  8. Teaching Process Design through Integrated Process Synthesis

    ERIC Educational Resources Information Center

    Metzger, Matthew J.; Glasser, Benjamin J.; Patel, Bilal; Hildebrandt, Diane; Glasser, David

    2012-01-01

    The design course is an integral part of chemical engineering education. A novel approach to the design course was recently introduced at the University of the Witwatersrand, Johannesburg, South Africa. The course aimed to introduce students to systematic tools and techniques for setting and evaluating performance targets for processes, as well as…

  9. Statistical Process Control for KSC Processing

    NASA Technical Reports Server (NTRS)

    Ford, Roger G.; Delgado, Hector; Tilley, Randy

    1996-01-01

    The 1996 Summer Faculty Fellowship Program and Kennedy Space Center (KSC) served as the basis for a research effort into statistical process control for KSC processing. The effort entailed several tasks and goals. The first was to develop a customized statistical process control (SPC) course for the Safety and Mission Assurance Trends Analysis Group. The actual teaching of this course took place over several weeks. In addition, an Internet version of the same course complete with animation and video excerpts from the course when it was taught at KSC was developed. The application of SPC to shuttle processing took up the rest of the summer research project. This effort entailed the evaluation of SPC use at KSC, both present and potential, due to the change in roles for NASA and the Single Flight Operations Contractor (SFOC). Individual consulting on SPC use was accomplished as well as an evaluation of SPC software for KSC use in the future. A final accomplishment of the orientation of the author to NASA changes, terminology, data format, and new NASA task definitions will allow future consultation when the needs arise.

  10. Process mapping: A user-friendly tool for process improvement

    NASA Astrophysics Data System (ADS)

    Carson, M. L.; Levine, L. O.

    1993-09-01

    Process maps aid administrative process improvement efforts by documenting processes in a rigorous yet understandable way. Icons, graphics, and text support process documentation, analysis, and improvement.

  11. Biomass process handbook

    SciTech Connect

    Not Available

    1983-01-01

    Descriptions are given of 42 processes which use biomass to produce chemical products. Marketing and economic background, process description, flow sheets, costs, major equipment, and availability of technology are given for each of the 42 processes. Some of the chemicals discussed are: ethanol, ethylene, acetaldehyde, butanol, butadiene, acetone, citric acid, gluconates, itaconic acid, lactic acid, xanthan gum, sorbitol, starch polymers, fatty acids, fatty alcohols, glycerol, soap, azelaic acid, perlargonic acid, nylon-11, jojoba oil, furfural, furfural alcohol, tetrahydrofuran, cellulose polymers, products from pulping wastes, and methane. Processes include acid hydrolysis, enzymatic hydrolysis, fermentation, distillation, Purox process, and anaerobic digestion.

  12. An improved plating process

    NASA Technical Reports Server (NTRS)

    Askew, John C.

    1994-01-01

    An alternative to the immersion process for the electrodeposition of chromium from aqueous solutions on the inside diameter (ID) of long tubes is described. The Vessel Plating Process eliminates the need for deep processing tanks, large volumes of solutions, and associated safety and environmental concerns. Vessel Plating allows the process to be monitored and controlled by computer thus increasing reliability, flexibility and quality. Elimination of the trivalent chromium accumulation normally associated with ID plating is intrinsic to the Vessel Plating Process. The construction and operation of a prototype Vessel Plating Facility with emphasis on materials of construction, engineered and operational safety and a unique system for rinse water recovery are described.

  13. Containerless processing technology

    NASA Technical Reports Server (NTRS)

    Oran, W. A.

    1983-01-01

    A brief review of containerless processing activities sponsored by NASA's Microgravity Science Division is presented. Attention is given to ground based systems such as shot tower processing of molten materials, single axis levitation and flight processing concepts including BeO processing aboard the Space Shuttle, a medium temperature three-axis acoustic positioning system and a high temperature single axis acoustic positioning system. In the future, more sophisticated experiments will be conducted using improved measurement techniques which will quantitatively define the advantages of containerless processing, as well as improve the understanding of nuclear kinetics and of the thermophysical properties of materials at high temperatures.

  14. Evaluation of steelmaking processes

    SciTech Connect

    Fruehan, R.J.

    1994-01-01

    Objective of the AISI Direct Steelmaking Program is to develop a process for producing steel directly from ore and coal; the process should be less capital intensive, consume less energy, and have higher productivity. A task force was formed to examine available processes: trough, posthearth, IRSID, Electric Arc Furnace, energy optimizing furnace. It is concluded that there is insufficient incentive to replace a working BOF with any of these processes to refine hot metal; however, if new steelmaking capacity is required, IRSID and EOF should be considered. A fully continuous process should not be considered until direct ironmaking and continuous refining are perfected.

  15. Process-based costing.

    PubMed

    Lee, Robert H; Bott, Marjorie J; Forbes, Sarah; Redford, Linda; Swagerty, Daniel L; Taunton, Roma Lee

    2003-01-01

    Understanding how quality improvement affects costs is important. Unfortunately, low-cost, reliable ways of measuring direct costs are scarce. This article builds on the principles of process improvement to develop a costing strategy that meets both criteria. Process-based costing has 4 steps: developing a flowchart, estimating resource use, valuing resources, and calculating direct costs. To illustrate the technique, this article uses it to cost the care planning process in 3 long-term care facilities. We conclude that process-based costing is easy to implement; generates reliable, valid data; and allows nursing managers to assess the costs of new or modified processes.

  16. Silicon production process evaluations

    NASA Technical Reports Server (NTRS)

    1982-01-01

    Chemical engineering analyses involving the preliminary process design of a plant (1,000 metric tons/year capacity) to produce silicon via the technology under consideration were accomplished. Major activities in the chemical engineering analyses included base case conditions, reaction chemistry, process flowsheet, material balance, energy balance, property data, equipment design, major equipment list, production labor and forward for economic analysis. The process design package provided detailed data for raw materials, utilities, major process equipment and production labor requirements necessary for polysilicon production in each process.

  17. Nonaqueous processing methods

    SciTech Connect

    Coops, M.S.; Bowersox, D.F.

    1984-09-01

    A high-temperature process utilizing molten salt extraction from molten metal alloys has been developed for purification of spent power reactor fuels. Experiments with laboratory-scale processing operations show that purification and throughput parameters comparable to the Barnwell Purex process can be achieved by pyrochemical processing in equipment one-tenth the size, with all wastes being discharged as stable metal alloys at greatly reduced volume and disposal cost. This basic technology can be developed for large-scale processing of spent reactor fuels. 13 references, 4 figures.

  18. Gas processing handbook

    SciTech Connect

    Not Available

    1982-04-01

    Brief details are given of processes including: BGC-Lurgi slagging gasification, COGAS, Exxon catalytic coal gasification, FW-Stoic 2-stage, GI two stage, HYGAS, Koppers-Totzek, Lurgi pressure gasification, Saarberg-Otto, Shell, Texaco, U-Gas, W-D.IGI, Wellman-Galusha, Westinghouse, and Winkler coal gasification processes; the Rectisol process; the Catacarb and the Benfield processes for removing CO/SUB/2, H/SUB/2s and COS from gases produced by the partial oxidation of coal; the selectamine DD, Selexol solvent, and Sulfinol gas cleaning processes; the sulphur-tolerant shift (SSK) process; and the Super-meth process for the production of high-Btu gas from synthesis gas.

  19. Dynamic modeling and control of a solid-sorbent CO{sub 2} capture process with two-stage bubbling fluidized bed adsorber reactor

    SciTech Connect

    Modekurti, S.; Bhattacharyya, D.; Zitney, S.

    2012-01-01

    Solid-sorbent-based CO{sub 2} capture processes have strong potential for reducing the overall energy penalty for post-combustion capture from the flue gas of a conventional pulverized coal power plant. However, the commercial success of this technology is contingent upon it operating over a wide range of capture rates, transient events, malfunctions, and disturbances, as well as under uncertainties. To study these operational aspects, a dynamic model of a solid-sorbent-based CO{sub 2} capture process has been developed. In this work, a one-dimensional (1D), non-isothermal, dynamic model of a two-stage bubbling fluidized bed (BFB) adsorber-reactor system with overflow-type weir configuration has been developed in Aspen Custom Modeler (ACM). The physical and chemical properties of the sorbent used in this study are based on a sorbent (32D) developed at National Energy Technology Laboratory (NETL). Each BFB is divided into bubble, emulsion, and cloud-wake regions with the assumptions that the bubble region is free of solids while both gas and solid phases coexist in the emulsion and cloud-wake regions. The BFB dynamic model includes 1D partial differential equations (PDEs) for mass and energy balances, along with comprehensive reaction kinetics. In addition to the two BFB models, the adsorber-reactor system includes 1D PDE-based dynamic models of the downcomer and outlet hopper, as well as models of distributors, control valves, and other pressure-drop devices. Consistent boundary and initial conditions are considered for simulating the dynamic model. Equipment items are sized and appropriate heat transfer options, wherever needed, are provided. Finally, a valid pressure-flow network is developed and a lower-level control system is designed. Using ACM, the transient responses of various process variables such as flue gas and sorbent temperatures, overall CO{sub 2} capture, level of solids in the downcomer and hopper have been studied by simulating typical

  20. Future Steelmaking Processes

    SciTech Connect

    Prof. R. J. Fruehan

    2004-09-20

    There is an increasing demand for an ironmaking process with lower capital cost, energy consumption and emissions than a blast furnace. It is the hypothesis of the present work that an optimized combination of two reasonable proven technologies will greatly enhance the overall process. An example is a rotary hearth furnace (RHF) linked to a smelter (e.g., AISI, HIsmelt). The objective of this research is to select promising process combinations, develop energy, materials balance and productivity models for the individual processes, conduct a limited amount of basic research on the processes and evaluate the process combinations. Three process combinations were selected with input from the industrial partners. The energy-materials and productivity models for the RHF, smelter, submerged arc furnace and CIRCOFER were developed. Since utilization of volatiles in coal is critical for energy and CO{sub 2} emission reduction, basic research on this topic was also conducted. The process models developed are a major product developed in this research. These models can be used for process evaluation by the industry. The process combinations of an RHF-Smelter and a simplified CIRCOFER-Smelter appear to be promising. Energy consumption is reduced and productivity increased. Work on this project is continuing using funds from other sources.

  1. Processes and process development in Japan

    NASA Technical Reports Server (NTRS)

    Noda, T.

    1986-01-01

    The commercialization of solar power generation necessitates the development of low cost manufacturing method of silicon suitable for solar cells. The manufacturing methods of semiconductor grade silicon (SEG-Si) and the development of solar grade silicon (SOG-Si) in foreign countries was investigated. It was concluded that the most efficient method of developing such materials was the hydrogen reduction process of trichlorosilane (TCS), using a fluidized bed reactor. The low cost reduction of polysilicon requires cost reductions of raw materials, energy, labor, and capital. These conditions were carefully reviewed. The overall conclusion was that a development program should be based on the TCS-FBR process and that the experimental program should be conducted in test facilities capable of producing 10 tons of silicon granules per year.

  2. Rumor Processes on and Discrete Renewal Processes

    NASA Astrophysics Data System (ADS)

    Gallo, Sandro; Garcia, Nancy L.; Junior, Valdivino Vargas; Rodríguez, Pablo M.

    2014-05-01

    We study two rumor processes on , the dynamics of which are related to an SI epidemic model with long range transmission. Both models start with one spreader at site and ignorants at all the other sites of , but differ by the transmission mechanism. In one model, the spreaders transmit the information within a random distance on their right, and in the other the ignorants take the information from a spreader within a random distance on their left. We obtain the probability of survival, information on the distribution of the range of the rumor and limit theorems for the proportion of spreaders. The key step of our proofs is to show that, in each model, the position of the spreaders on can be related to a suitably chosen discrete renewal process.

  3. Universal Heliophysical Processes

    NASA Technical Reports Server (NTRS)

    Gopalswamy, Natchimuthuk

    2011-01-01

    The physical processes in the heliospace are a direct consequence of the Sun s mass and electromagnetic emissions. There has been enormous progress in studying these processes since the dawn of the space age half a century ago. The heliospace serves as a great laboratory to study numerous physical processes, using the vast array of ground and spacebased measurements of various physical quantities. The observational capabilities collectively form the Great Observatory to make scientific investigations not envisioned by individual instrument teams. The International Heliophysical Year (IHY) program has been promoting scientific investigations on the universality of physical processes such as shocks, particle acceleration, dynamo, magnetic reconnection, magnetic flux ropes, plasma-neutral matter interactions, turbulence, and several other topics. This chapter highlights scientific deliberations on these and related topics that took place during the IAGA session on "Universal Heliophysical Processes" in Sopron, Hungary. The session featured several invited and contributed papers that focused on observations, theory and modeling of the universal heliophysical processes.

  4. Pultrusion process characterization

    NASA Technical Reports Server (NTRS)

    Vaughan, James G.; Hackett, Robert M.

    1991-01-01

    Pultrusion is a process through which high-modulus, lightweight composite structural members such as beams, truss components, stiffeners, etc., are manufactured. The pultrusion process, though a well-developed processing art, lacks a fundamental scientific understanding. The objective here was to determine, both experimentally and analytically, the process parameters most important in characterizing and optimizing the pultrusion of uniaxial fibers. The effects of process parameter interactions were experimentally examined as a function of the pultruded product properties. A numerical description based on these experimental results was developed. An analytical model of the pultrusion process was also developed. The objective of the modeling effort was the formulation of a two-dimensional heat transfer model and development of solutions for the governing differential equations using the finite element method.

  5. Badge Office Process Analysis

    SciTech Connect

    Haurykiewicz, John Paul; Dinehart, Timothy Grant; Parker, Robert Young

    2016-05-12

    The purpose of this process analysis was to analyze the Badge Offices’ current processes from a systems perspective and consider ways of pursuing objectives set forth by SEC-PS, namely increased customer flow (throughput) and reduced customer wait times. Information for the analysis was gathered for the project primarily through Badge Office Subject Matter Experts (SMEs), and in-person observation of prevailing processes. Using the information gathered, a process simulation model was constructed to represent current operations and allow assessment of potential process changes relative to factors mentioned previously. The overall purpose of the analysis was to provide SEC-PS management with information and recommendations to serve as a basis for additional focused study and areas for potential process improvements in the future.

  6. Spitzer Telemetry Processing System

    NASA Technical Reports Server (NTRS)

    Stanboli, Alice; Martinez, Elmain M.; McAuley, James M.

    2013-01-01

    The Spitzer Telemetry Processing System (SirtfTlmProc) was designed to address objectives of JPL's Multi-mission Image Processing Lab (MIPL) in processing spacecraft telemetry and distributing the resulting data to the science community. To minimize costs and maximize operability, the software design focused on automated error recovery, performance, and information management. The system processes telemetry from the Spitzer spacecraft and delivers Level 0 products to the Spitzer Science Center. SirtfTlmProc is a unique system with automated error notification and recovery, with a real-time continuous service that can go quiescent after periods of inactivity. The software can process 2 GB of telemetry and deliver Level 0 science products to the end user in four hours. It provides analysis tools so the operator can manage the system and troubleshoot problems. It automates telemetry processing in order to reduce staffing costs.

  7. Low-temperature, solution-processed ZrO2:B thin film: a bifunctional inorganic/organic interfacial glue for flexible thin-film transistors.

    PubMed

    Park, Jee Ho; Oh, Jin Young; Han, Sun Woong; Lee, Tae Il; Baik, Hong Koo

    2015-03-04

    A solution-processed boron-doped peroxo-zirconium oxide (ZrO2:B) thin film has been found to have multifunctional characteristics, providing both hydrophobic surface modification and a chemical glue layer. Specifically, a ZrO2:B thin film deposited on a hydrophobic layer becomes superhydrophilic following ultraviolet-ozone (UVO) treatment, whereas the same treatment has no effect on the hydrophobicity of the hydrophobic layer alone. Investigation of the ZrO2:B/hydrophobic interface layer using angle-resolved X-ray photoelectron spectroscopy (AR XPS) confirmed it to be chemically bonded like glue. Using the multifunctional nature of the ZrO2:B thin film, flexible amorphous indium oxide (In2O3) thin-film transistors (TFTs) were subsequently fabricated on a polyimide substrate along with a ZrO2:B/poly-4-vinylphenol (PVP) dielectric. An aqueous In2O3 solution was successfully coated onto the ZrO2:B/PVP dielectric, and the surface and chemical properties of the PVP and ZrO2:B thin films were analyzed by contact angle measurement, atomic force microscopy (AFM), Fourier transform infrared (FT-IR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). The surface-engineered PVP dielectric was found to have a lower leakage current density (Jleak) of 4.38 × 10(-8) A/cm(2) at 1 MV/cm, with no breakdown behavior observed up to a bending radius of 5 mm. In contrast, the electrical characteristics of the flexible amorphous In2O3 TFT such as on/off current ratio (Ion/off) and electron mobility remained similar up to 10 mm of bending without degradation, with the device being nonactivated at a bending radius of 5 mm. These results suggest that ZrO2:B thin films could be used for low-temperature, solution-processed surface-modified flexible devices.

  8. Silicon production process evaluations

    NASA Technical Reports Server (NTRS)

    1981-01-01

    The chemical engineering analysis of the preliminary process design of a process for producing solar cell grade silicon from dichlorosilane is presented. A plant to produce 1,000 MT/yr of silicon is analyzed. Progress and status for the plant design are reported for the primary activities of base case conditions (60 percent), reaction chemistry (50 percent), process flow diagram (35 percent), energy balance (10 percent), property data (10 percent) and equipment design (5 percent).

  9. The process audit.

    PubMed

    Hammer, Michael

    2007-04-01

    Few executives question the idea that by redesigning business processes--work that runs from end to end across an enterprise--they can achieve extraordinary improvements in cost, quality, speed, profitability, and other key areas Yet in spite of their intentions and investments, many executives flounder, unsure about what exactly needs to be changed, by how much, and when. As a result, many organizations make little progress--if any at all--in their attempts to transform business processes. Michael Hammer has spent the past five years working with a group of leading companies to develop the Process and Enterprise Maturity Model (PEMM), a new framework that helps executives comprehend, formulate, and assess process-based transformation efforts. He has identified two distinct groups of characteristics that are needed for business processes to perform exceptionally well over a long period of time. Process enablers, which affect individual processes, determine how well a process is able to function. They are mutually interdependent--if any are missing, the others will be ineffective. However, enablers are not enough to develop high-performance processes; they only provide the potential to deliver high performance. A company must also possess or establish organizational capabilities that allow the business to offer a supportive environment. Together, the enablers and the capabilities provide an effective way for companies to plan and evaluate process-based transformations. PEMM is different from other frameworks, such as Capability Maturity Model Integration (CMMI), because it applies to all industries and all processes. The author describes how several companies--including Michelin, CSAA, Tetra Pak, Shell, Clorox, and Schneider National--have successfully used PEMM in various ways and at different stages to evaluate the progress of their process-based transformation efforts.

  10. Image Processing Research

    DTIC Science & Technology

    1976-09-30

    Processing Institute University of Southern California University Park Los Angeles, California 90007 Sponsored by Advanced Research Projects Agency...Image Processing Institute University of Southern California University Park Los Angeles, California 90007 Accession For "mis GRA&l DTIC... Park Los Angeles, California 90007 ’«.’J. He »-’OH r ircuHiTr CLASJIUCATION UNCLASSIFIED 2ö. chouc 3 NEPOH f TITLE IMAGE PROCESSING

  11. Materials processing in space

    SciTech Connect

    Oran, W.A.

    1982-11-01

    A brief overview of the current Materials Processing in Space Program is given, including a tentative schedule of flight experiments. Some recent results of processing materials (e.g., polymers and eutectic materials) in a microgravity environment are given, along with a discussion on additional proposed flight experiments. Ground-based results and the rationale for flight experimentation will be presented for other materials processes, including crystal growth.

  12. Fjords: Processes and products

    SciTech Connect

    Syvitski, J.P.M.; Burrell, D.C.; Skei, J.M.

    1987-01-01

    Fjords are a major feature of coasts and provide geologists and oceanographers with an excellent environment for studying and modeling coastal processes and products. This book brings together and integrates an enormous amount of information on fjords and provides the reader with a thorough, interdisciplinary account of current research with emphasis on sedimentary processes. The processes demonstrated in fjords are often relevant to the estuarine or open ocean environment.

  13. Multiphoton processes: conference proceedings

    SciTech Connect

    Lambropoulos, P.; Smith, S.J.

    1984-01-01

    The chapters of this volume represent the invited papers delivered at the conference. They are arranged according to thermatic proximity beginning with atoms and continuing with molecules and surfaces. Section headings include multiphoton processes in atoms, field fluctuations and collisions in multiphoton process, and multiphoton processes in molecules and surfaces. Abstracts of individual items from the conference were prepared separately for the data base. (GHT)

  14. TEP process flow diagram

    SciTech Connect

    Wilms, R Scott; Carlson, Bryan; Coons, James; Kubic, William

    2008-01-01

    This presentation describes the development of the proposed Process Flow Diagram (PFD) for the Tokamak Exhaust Processing System (TEP) of ITER. A brief review of design efforts leading up to the PFD is followed by a description of the hydrogen-like, air-like, and waterlike processes. Two new design values are described; the mostcommon and most-demanding design values. The proposed PFD is shown to meet specifications under the most-common and mostdemanding design values.

  15. Digital signal processing

    NASA Astrophysics Data System (ADS)

    Oppenheim, A. V.; Baggeroer, A. B.; Lim, J. S.; Musicus, B. R.; Mook, D. R.; Duckworth, G. L.; Bordley, T. E.; Curtis, S. R.; Deadrick, D. S.; Dove, W. P.

    1984-01-01

    Signal and image processing research projects are described. Topics include: (1) modeling underwater acoustic propagation; (2) image restoration; (3) signal reconstruction; (4) speech enhancement; (5) pitch detection; (6) spectral analysis; (7) speech synthesis; (8) speech enhancement; (9) autoregressive spectral estimation; (10) knowledge based array processing; (11) speech analysis; (12) estimating the degree of coronary stenosis with image processing; (13) automatic target detection; and (14) video conferencing.

  16. GPS Decision Analysis Process

    DTIC Science & Technology

    2005-06-23

    712 A/B: GPS Decision Analysis Process Revised title:___________________________________________________________________ Presented in (input and Bold...JUN 2005 2. REPORT TYPE N/A 3. DATES COVERED - 4. TITLE AND SUBTITLE GPS Decision Analysis Process 5a. CONTRACT NUMBER 5b. GRANT NUMBER...Prescribed by ANSI Std Z39-18 GPS Decision Analysis Process Nisha Shah The Boeing Company 73rd MORS Symposium US Military Academy – West Point 21-23

  17. Containerless processing technology analysis

    NASA Technical Reports Server (NTRS)

    Rush, J. E.

    1982-01-01

    Research on acoustic levitation, air-jet levitation, and heat transfer from molten samples is reported. The goal was to obtain a better understanding and improving the quality of containerless processing systems. These systems are applied to the processing of materials in situations in which contact with a container must be avoided, and have potential application in both ground based and orbiting laboratories. Containerless processing is reviewed. The development of glasses from materials which normally crystallize upon cooling, are studied.

  18. NASA Hazard Analysis Process

    NASA Technical Reports Server (NTRS)

    Deckert, George

    2010-01-01

    This viewgraph presentation reviews The NASA Hazard Analysis process. The contents include: 1) Significant Incidents and Close Calls in Human Spaceflight; 2) Subsystem Safety Engineering Through the Project Life Cycle; 3) The Risk Informed Design Process; 4) Types of NASA Hazard Analysis; 5) Preliminary Hazard Analysis (PHA); 6) Hazard Analysis Process; 7) Identify Hazardous Conditions; 8) Consider All Interfaces; 9) Work a Preliminary Hazard List; 10) NASA Generic Hazards List; and 11) Final Thoughts

  19. Polyimide processing additives

    NASA Technical Reports Server (NTRS)

    Fletcher, James C. (Inventor); Pratt, J. Richard (Inventor); St.clair, Terry L. (Inventor); Stoakley, Diane M. (Inventor); Burks, Harold D. (Inventor)

    1992-01-01

    A process for preparing polyimides having enhanced melt flow properties is described. The process consists of heating a mixture of a high molecular weight poly-(amic acid) or polyimide with a low molecular weight amic acid or imide additive in the range of 0.05 to 15 percent by weight of additive. The polyimide powders so obtained show improved processability, as evidenced by lower melt viscosity by capillary rheometry. Likewise, films prepared from mixtures of polymers with additives show improved processability with earlier onset of stretching by TMA.

  20. Living olefin polymerization processes

    DOEpatents

    Schrock, R.R.; Baumann, R.

    1999-03-30

    Processes for the living polymerization of olefin monomers with terminal carbon-carbon double bonds are disclosed. The processes employ initiators that include a metal atom and a ligand having two group 15 atoms and a group 16 atom or three group 15 atoms. The ligand is bonded to the metal atom through two anionic or covalent bonds and a dative bond. The initiators are particularly stable under reaction conditions in the absence of olefin monomer. The processes provide polymers having low polydispersities, especially block copolymers having low polydispersities. It is an additional advantage of these processes that, during block copolymer synthesis, a relatively small amount of homopolymer is formed.

  1. Living olefin polymerization processes

    DOEpatents

    Schrock, Richard R.; Baumann, Robert

    1999-01-01

    Processes for the living polymerization of olefin monomers with terminal carbon-carbon double bonds are disclosed. The processes employ initiators that include a metal atom and a ligand having two group 15 atoms and a group 16 atom or three group 15 atoms. The ligand is bonded to the metal atom through two anionic or covalent bonds and a dative bond. The initiators are particularly stable under reaction conditions in the absence of olefin monomer. The processes provide polymers having low polydispersities, especially block copolymers having low polydispersities. It is an additional advantage of these processes that, during block copolymer synthesis, a relatively small amount of homopolymer is formed.

  2. Living olefin polymerization processes

    DOEpatents

    Schrock, Richard R.; Baumann, Robert

    2003-08-26

    Processes for the living polymerization of olefin monomers with terminal carbon-carbon double bonds are disclosed. The processes employ initiators that include a metal atom and a ligand having two group 15 atoms and a group 16 atom or three group 15 atoms. The ligand is bonded to the metal atom through two anionic or covalent bonds and a dative bond. The initiators are particularly stable under reaction conditions in the absence of olefin monomer. The processes provide polymers having low polydispersities, especially block copolymers having low polydispersities. It is an additional advantage of these processes that, during block copolymer synthesis, a relatively small amount of homopolymer is formed.

  3. Living olefin polymerization processes

    DOEpatents

    Schrock, Richard R.; Bauman, Robert

    2006-11-14

    Processes for the living polymerization of olefin monomers with terminal carbon-carbon double bonds are disclosed. The processes employ initiators that include a metal atom and a ligand having two group 15 atoms and a group 16 atom or three group 15 atoms. The ligand is bonded to the metal atom through two anionic or covalent bonds and a dative bond. The initiators are particularly stable under reaction conditions in the absence of olefin monomer. The processes provide polymers having low polydispersities, especially block copolymers having low polydispersities. It is an additional advantage of these processes that, during block copolymer synthesis, a relatively small amount of homopolymer is formed.

  4. Polyimide processing additives

    NASA Technical Reports Server (NTRS)

    Pratt, J. Richard (Inventor); St.clair, Terry L. (Inventor); Stoakley, Diane M. (Inventor); Burks, Harold D. (Inventor)

    1993-01-01

    A process for preparing polyimides having enhanced melt flow properties is described. The process consists of heating a mixture of a high molecular weight poly-(amic acid) or polyimide with a low molecular weight amic acid or imide additive in the range of 0.05 to 15 percent by weight of the additive. The polyimide powders so obtained show improved processability, as evidenced by lower melt viscosity by capillary rheometry. Likewise, films prepared from mixtures of polymers with additives show improved processability with earlier onset of stretching by TMA.

  5. Central waste processing system

    NASA Technical Reports Server (NTRS)

    Kester, F. L.

    1973-01-01

    A new concept for processing spacecraft type wastes has been evaluated. The feasibility of reacting various waste materials with steam at temperatures of 538 - 760 C in both a continuous and batch reactor with residence times from 3 to 60 seconds has been established. Essentially complete gasification is achieved. Product gases are primarily hydrogen, carbon dioxide, methane, and carbon monoxide. Water soluble synthetic wastes are readily processed in a continuous tubular reactor at concentrations up to 20 weight percent. The batch reactor is able to process wet and dry wastes at steam to waste weight ratios from 2 to 20. Feces, urine, and synthetic wastes have been successfully processed in the batch reactor.

  6. JSME scatterometer data processing

    NASA Technical Reports Server (NTRS)

    1977-01-01

    A software system was developed which processes digitized scatterometer data from the 13.3 GHz, 1.6 GHz and 400 MHz scatterometer systems. In addition to this, the hardware capability has been developed to recover the raw analog radar signals and the aircraft parameters from an ADAS data stream in a digital format for processing by the software package. Software for the preparation of data reports and chart presentation of scattering coefficients time histories has also been developed. This report documents the development of the software, describes key components of the processing system and presents examples of the processed data and procedure for software operation.

  7. RNA Processing and Export

    PubMed Central

    Hocine, Sami; Singer, Robert H.; Grünwald, David

    2010-01-01

    Messenger RNAs undergo 5' capping, splicing, 3'-end processing, and export before translation in the cytoplasm. It has become clear that these mRNA processing events are tightly coupled and have a profound effect on the fate of the resulting transcript. This processing is represented by modifications of the pre-mRNA and loading of various protein factors. The sum of protein factors that stay with the mRNA as a result of processing is modified over the life of the transcript, conferring significant regulation to its expression. PMID:20961978

  8. Powder towpreg process development

    NASA Technical Reports Server (NTRS)

    Baucom, Robert M.; Marchello, Joseph M.

    1991-01-01

    The process for dry powder impregnation of carbon fiber tows being developed at LaRC overcomes many of the difficulties associated with melt, solution, and slurry prepregging. In the process, fluidized powder is deposited on spread tow bundles and fused to the fibers by radiant heating. Impregnated tows have been produced for preform, weaving, and composite materials applications. Design and operating data correlations were developed for scale up of the process to commercial operation. Bench scale single tow experiments at tow speeds up to 50 cm/sec have demonstrated that the process can be controlled to produce weavable towpreg. Samples were woven and molded into preform material of good quality.

  9. Biased predecision processing.

    PubMed

    Brownstein, Aaron L

    2003-07-01

    Decision makers conduct biased predecision processing when they restructure their mental representation of the decision environment to favor one alternative before making their choice. The question of whether biased predecision processing occurs has been controversial since L. Festinger (1957) maintained that it does not occur. The author reviews relevant research in sections on theories of cognitive dissonance, decision conflict, choice certainty, action control, action phases, dominance structuring, differentiation and consolidation, constructive processing, motivated reasoning, and groupthink. Some studies did not find evidence of biased predecision processing, but many did. In the Discussion section, the moderators are summarized and used to assess the theories.

  10. Industrial Process Surveillance System

    DOEpatents

    Gross, Kenneth C.; Wegerich, Stephan W; Singer, Ralph M.; Mott, Jack E.

    2001-01-30

    A system and method for monitoring an industrial process and/or industrial data source. The system includes generating time varying data from industrial data sources, processing the data to obtain time correlation of the data, determining the range of data, determining learned states of normal operation and using these states to generate expected values, comparing the expected values to current actual values to identify a current state of the process closest to a learned, normal state; generating a set of modeled data, and processing the modeled data to identify a data pattern and generating an alarm upon detecting a deviation from normalcy.

  11. Lyophilization process design space.

    PubMed

    Patel, Sajal Manubhai; Pikal, Michael J

    2013-11-01

    The application of key elements of quality by design (QbD), such as risk assessment, process analytical technology, and design space, is discussed widely as it relates to freeze-drying process design and development. However, this commentary focuses on constructing the Design and Control Space, particularly for the primary drying step of the freeze-drying process. Also, practical applications and considerations of claiming a process Design Space under the QbD paradigm have been discussed. © 2013 Wiley Periodicals, Inc. and the American Pharmacists Association.

  12. Mineral Processing Sector

    EPA Pesticide Factsheets

    Find environmental regulatory and compliance information for the nonmetallic mineral processing sector (NAICS 327), including NESHAPs for asbestos and hazardous waste, and wastewater permit information.

  13. Acoustic Signal Processing

    NASA Astrophysics Data System (ADS)

    Hartmann, William M.; Candy, James V.

    Signal processing refers to the acquisition, storage, display, and generation of signals - also to the extraction of information from signals and the re-encoding of information. As such, signal processing in some form is an essential element in the practice of all aspects of acoustics. Signal processing algorithms enable acousticians to separate signals from noise, to perform automatic speech recognition, or to compress information for more efficient storage or transmission. Signal processing concepts are the building blocks used to construct models of speech and hearing. Now, in the 21st century, all signal processing is effectively digital signal processing. Widespread access to high-speed processing, massive memory, and inexpensive software make signal processing procedures of enormous sophistication and power available to anyone who wants to use them. Because advanced signal processing is now accessible to everybody, there is a need for primers that introduce basic mathematical concepts that underlie the digital algorithms. The present handbook chapter is intended to serve such a purpose.

  14. Industrial process surveillance system

    DOEpatents

    Gross, Kenneth C.; Wegerich, Stephan W.; Singer, Ralph M.; Mott, Jack E.

    1998-01-01

    A system and method for monitoring an industrial process and/or industrial data source. The system includes generating time varying data from industrial data sources, processing the data to obtain time correlation of the data, determining the range of data, determining learned states of normal operation and using these states to generate expected values, comparing the expected values to current actual values to identify a current state of the process closest to a learned, normal state; generating a set of modeled data, and processing the modeled data to identify a data pattern and generating an alarm upon detecting a deviation from normalcy.

  15. Industrial process surveillance system

    DOEpatents

    Gross, K.C.; Wegerich, S.W.; Singer, R.M.; Mott, J.E.

    1998-06-09

    A system and method are disclosed for monitoring an industrial process and/or industrial data source. The system includes generating time varying data from industrial data sources, processing the data to obtain time correlation of the data, determining the range of data, determining learned states of normal operation and using these states to generate expected values, comparing the expected values to current actual values to identify a current state of the process closest to a learned, normal state; generating a set of modeled data, and processing the modeled data to identify a data pattern and generating an alarm upon detecting a deviation from normalcy. 96 figs.

  16. Future integrated design process

    NASA Technical Reports Server (NTRS)

    Meyer, D. D.

    1980-01-01

    The design process is one of the sources used to produce requirements for a computer system to integrate and manage product design data, program management information, and technical computation and engineering data management activities of the aerospace design process. Design activities were grouped chronologically and explored for activity type, activity interface, data quantity, and data flow. The work was based on analysis of the design process of several typical aerospace products, including both conventional and supersonic airplanes and a hydrofoil design. Activities examined included research, preliminary design, detail design, manufacturing interface, product verification, and product support. The design process was then described in an IPAD environment--the future.

  17. Ultrasonics in food processing.

    PubMed

    Chandrapala, Jayani; Oliver, Christine; Kentish, Sandra; Ashokkumar, Muthupandian

    2012-09-01

    In recent years, the physical and chemical effects of ultrasound in liquid and solid media have been extensively used in food processing applications. Harnessing the physical forces generated by ultrasound, in the absence and presence of cavitation, for specific food processing applications such as emulsification, filtration, tenderisation and functionality modification have been highlighted. While some applications, such as filtration and emulsification are "mature" industrial processes, other applications, such as functionality modification, are still in their early stages of development. However, various investigations discussed suggest that ultrasonic processing of food and dairy ingredients is a potential and viable technology that will be used by many food industries in the near future.

  18. Chemical process hazards analysis

    SciTech Connect

    1996-02-01

    The Office of Worker Health and Safety (EH-5) under the Assistant Secretary for the Environment, Safety and Health of the US Department (DOE) has published two handbooks for use by DOE contractors managing facilities and processes covered by the Occupational Safety and Health Administration (OSHA) Rule for Process Safety Management of Highly Hazardous Chemicals (29 CFR 1910.119), herein referred to as the PSM Rule. The PSM Rule contains an integrated set of chemical process safety management elements designed to prevent chemical releases that can lead to catastrophic fires, explosions, or toxic exposures. The purpose of the two handbooks, ``Process Safety Management for Highly Hazardous Chemicals`` and ``Chemical Process Hazards Analysis,`` is to facilitate implementation of the provisions of the PSM Rule within the DOE. The purpose of this handbook ``Chemical Process Hazards Analysis,`` is to facilitate, within the DOE, the performance of chemical process hazards analyses (PrHAs) as required under the PSM Rule. It provides basic information for the performance of PrHAs, and should not be considered a complete resource on PrHA methods. Likewise, to determine if a facility is covered by the PSM rule, the reader should refer to the handbook, ``Process Safety Management for Highly Hazardous Chemicals`` (DOE- HDBK-1101-96). Promulgation of the PSM Rule has heightened the awareness of chemical safety management issues within the DOE. This handbook is intended for use by DOE facilities and processes covered by the PSM rule to facilitate contractor implementation of the PrHA element of the PSM Rule. However, contractors whose facilities and processes not covered by the PSM Rule may also use this handbook as a basis for conducting process hazards analyses as part of their good management practices. This handbook explains the minimum requirements for PrHAs outlined in the PSM Rule. Nowhere have requirements been added beyond what is specifically required by the rule.

  19. EARSEC SAR processing system

    NASA Astrophysics Data System (ADS)

    Protheroe, Mark; Sloggett, David R.; Sieber, Alois J.

    1994-12-01

    Traditionally, the production of high quality Synthetic Aperture Radar imagery has been an area where a potential user would have to expend large amounts of money in either the bespoke development of a processing chain dedicated to his requirements or in the purchase of a dedicated hardware platform adapted using accelerator boards and enhanced memory management. Whichever option the user adopted there were limitations based on the desire for a realistic throughput in data load and time. The user had a choice, made early in the purchase, for either a system that adopted innovative algorithmic manipulation, to limit the processing time of the purchase of expensive hardware. The former limits the quality of the product, while the latter excludes the user from any visibility into the processing chain. Clearly there was a need for a SAR processing architecture that gave the user a choice into the methodology to be adopted for a particular processing sequence, allowing him to decide on either a quick (lower quality) product or a detailed slower (high quality) product, without having to change the algorithmic base of his processor or the hardware platform. The European Commission, through the Advanced Techniques unit of the Joint Research Centre (JRC) Institute for Remote Sensing at Ispra in Italy, realizing the limitations on current processing abilities, initiated its own program to build airborne SAR and Electro-Optical (EO) sensor systems. This program is called the European Airborne Remote Sensing Capabilities (EARSEC) program. This paper describes the processing system developed for the airborne SAR sensor system. The paper considers the requirements for the system and the design of the EARSEC Airborne SAR Processing System. It highlights the development of an open SAR processing architecture where users have full access to intermediate products that arise from each of the major processing stages. It also describes the main processing stages in the overall

  20. Food processing and allergenicity.

    PubMed

    Verhoeckx, Kitty C M; Vissers, Yvonne M; Baumert, Joseph L; Faludi, Roland; Feys, Marcel; Flanagan, Simon; Herouet-Guicheney, Corinne; Holzhauser, Thomas; Shimojo, Ryo; van der Bolt, Nieke; Wichers, Harry; Kimber, Ian

    2015-06-01

    Food processing can have many beneficial effects. However, processing may also alter the allergenic properties of food proteins. A wide variety of processing methods is available and their use depends largely on the food to be processed. In this review the impact of processing (heat and non-heat treatment) on the allergenic potential of proteins, and on the antigenic (IgG-binding) and allergenic (IgE-binding) properties of proteins has been considered. A variety of allergenic foods (peanuts, tree nuts, cows' milk, hens' eggs, soy, wheat and mustard) have been reviewed. The overall conclusion drawn is that processing does not completely abolish the allergenic potential of allergens. Currently, only fermentation and hydrolysis may have potential to reduce allergenicity to such an extent that symptoms will not be elicited, while other methods might be promising but need more data. Literature on the effect of processing on allergenic potential and the ability to induce sensitisation is scarce. This is an important issue since processing may impact on the ability of proteins to cause the acquisition of allergic sensitisation, and the subject should be a focus of future research. Also, there remains a need to develop robust and integrated methods for the risk assessment of food allergenicity. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

  1. Contaminated nickel scrap processing

    SciTech Connect

    Compere, A.L.; Griffith, W.L.; Hayden, H.W.; Johnson, J.S. Jr.; Wilson, D.F.

    1994-12-01

    The DOE will soon choose between treating contaminated nickel scrap as a legacy waste and developing high-volume nickel decontamination processes. In addition to reducing the volume of legacy wastes, a decontamination process could make 200,000 tons of this strategic metal available for domestic use. Contaminants in DOE nickel scrap include {sup 234}Th, {sup 234}Pa, {sup 137}Cs, {sup 239}Pu (trace), {sup 60}Co, U, {sup 99}Tc, and {sup 237}Np (trace). This report reviews several industrial-scale processes -- electrorefining, electrowinning, vapormetallurgy, and leaching -- used for the purification of nickel. Conventional nickel electrolysis processes are particularly attractive because they use side-stream purification of process solutions to improve the purity of nickel metal. Additionally, nickel purification by electrolysis is effective in a variety of electrolyte systems, including sulfate, chloride, and nitrate. Conventional electrorefining processes typically use a mixed electrolyte which includes sulfate, chloride, and borate. The use of an electrorefining or electrowinning system for scrap nickel recovery could be combined effectively with a variety of processes, including cementation, solvent extraction, ion exchange, complex-formation, and surface sorption, developed for uranium and transuranic purification. Selected processes were reviewed and evaluated for use in nickel side-stream purification. 80 refs.

  2. Process for preparing radiopharmaceuticals

    DOEpatents

    Barak, Morton; Winchell, Harry S.

    1977-01-04

    A process for the preparation of technetium-99m labeled pharmaceuticals is disclosed. The process comprises initially isolating technetium-99m pertechnetate by adsorption upon an adsorbent packing in a chromatographic column. The technetium-99m is then eluted from the packing with a biological compound to form a radiopharmaceutical.

  3. ELECTRONIC DATA PROCESSING EDUCATION.

    ERIC Educational Resources Information Center

    TONDOW, MURRAY

    EDUCATION HAS BEEN SLOW IN FULLY UTILIZING ELECTRONIC DATA PROCESSING EQUIPMENT (EDP). EDUCATOR CONFIDENCE IN THE EDP HAS GROWN, HOWEVER, AS A RESULT OF THE SUCCESS OF ELECTRONIC DATA PROCESSING IN SCIENCE, INDUSTRY, AND OTHER PROFESSIONS. THE DEVELOPMENT OF SOLID STATE TRANSISTORIZED COMPUTERS HAS MADE POWERFUL DESK-SIZE COMPUTERS A REALITY AND…

  4. HEPA filter dissolution process

    DOEpatents

    Brewer, K.N.; Murphy, J.A.

    1994-02-22

    A process is described for dissolution of spent high efficiency particulate air (HEPA) filters and then combining the complexed filter solution with other radioactive wastes prior to calcining the mixed and blended waste feed. The process is an alternate to a prior method of acid leaching the spent filters which is an inefficient method of treating spent HEPA filters for disposal. 4 figures.

  5. Hepa filter dissolution process

    DOEpatents

    Brewer, Ken N.; Murphy, James A.

    1994-01-01

    A process for dissolution of spent high efficiency particulate air (HEPA) filters and then combining the complexed filter solution with other radioactive wastes prior to calcining the mixed and blended waste feed. The process is an alternate to a prior method of acid leaching the spent filters which is an inefficient method of treating spent HEPA filters for disposal.

  6. Hyperspectral image processing methods

    USDA-ARS?s Scientific Manuscript database

    Hyperspectral image processing refers to the use of computer algorithms to extract, store and manipulate both spatial and spectral information contained in hyperspectral images across the visible and near-infrared portion of the electromagnetic spectrum. A typical hyperspectral image processing work...

  7. The Educational Process.

    ERIC Educational Resources Information Center

    Australian Coll. of Education, Carlton, Victoria.

    This book consists of 18 selected papers that focus on the broad topic of the educational process. All the papers were originally presented at the Fourteenth Annual Conference of the Australian College of Education, which was held in May 1973. Titles of the papers include "The Educational Process: The Raw Material,""Towards a…

  8. Building Successful Cleaning Processes.

    ERIC Educational Resources Information Center

    Walker, John P.

    2002-01-01

    Discusses how to build a successful cleaning process in order to most effectively maintain school facilities, explaining that the cleaning processes used plays a critical role in productivity. Focuses on: developing a standardized system; making sure that employees have the right tools for the work they perform; training employees; tracking and…

  9. Image processing mini manual

    NASA Technical Reports Server (NTRS)

    Matthews, Christine G.; Posenau, Mary-Anne; Leonard, Desiree M.; Avis, Elizabeth L.; Debure, Kelly R.; Stacy, Kathryn; Vonofenheim, Bill

    1992-01-01

    The intent is to provide an introduction to the image processing capabilities available at the Langley Research Center (LaRC) Central Scientific Computing Complex (CSCC). Various image processing software components are described. Information is given concerning the use of these components in the Data Visualization and Animation Laboratory at LaRC.

  10. Hybrid quantum information processing

    SciTech Connect

    Furusawa, Akira

    2014-12-04

    I will briefly explain the definition and advantage of hybrid quantum information processing, which is hybridization of qubit and continuous-variable technologies. The final goal would be realization of universal gate sets both for qubit and continuous-variable quantum information processing with the hybrid technologies. For that purpose, qubit teleportation with a continuousvariable teleporter is one of the most important ingredients.

  11. Building Successful Cleaning Processes.

    ERIC Educational Resources Information Center

    Walker, John P.

    2002-01-01

    Discusses how to build a successful cleaning process in order to most effectively maintain school facilities, explaining that the cleaning processes used plays a critical role in productivity. Focuses on: developing a standardized system; making sure that employees have the right tools for the work they perform; training employees; tracking and…

  12. Monitoring Process Effectiveness

    EPA Science Inventory

    Treatment of municipal sludges to produce biosolids which meet federal and/or state requirements for land application requires process monitoring. The goal of process monitoring is to produce biosolids of consistent and reliable quality. In its simplest form, for Class B treatme...

  13. METAL PLATING PROCESS

    DOEpatents

    Walker, D.E.; Noland, R.A.

    1958-08-12

    A process ts described for obtaining a closely bonded coating of steel or iron on uranium. The process consists of providing, between the steel and uramium. a layer of silver. amd then pressure rolling tbe assembly at about 600 deg C until a reduction of from l0 to 50% has been obtained.

  14. Patterns in neural processing

    NASA Astrophysics Data System (ADS)

    Engineer, Sunu

    2012-03-01

    In this paper we propose a model for neural processing that addresses both the evolutionary and functional aspects of neural systems that are observed in nature, from the simplest neural collections to dense large scale associations such as human brains. We propose both an architecture and a process in which these components interact to create the emergent behavior that we define as the 'mind'.

  15. Process Writing with Hawthorne.

    ERIC Educational Resources Information Center

    Edwards, Lita R.

    Teachers can use the process writing format for many assignments to teach and refine more skills than are often incorporated in older methods, and this is exemplified by a teaching unit comparing two short stories by Nathaniel Hawthorne. Peer conferences and peer editing in the revision stages, which are features of the process model, can lead to…

  16. On Cognizing Cognitive Processes.

    ERIC Educational Resources Information Center

    Rimoldi, H. J. A.

    In this report on cognitive processes, a discussion of the rationale and assumptions used by investigators explains the experimental procedures. To determine actual cognitive problem-solving processes, (rather than inferring them from results), subjects in these studies were presented with a problem and allowed to ask a sequence of questions which…

  17. Space processing applications bibliography

    NASA Technical Reports Server (NTRS)

    1978-01-01

    This special bibliography lists 724 articles, papers, and reports which discuss various aspects of the use of the space environment for materials science research or for commercial enterprise. The potentialities of space processing and the improved materials processes that are made possible by the unique aspects of the space environment are emphasized. References identified in April, 1978 are cited.

  18. Process Writing with Hawthorne.

    ERIC Educational Resources Information Center

    Edwards, Lita R.

    Teachers can use the process writing format for many assignments to teach and refine more skills than are often incorporated in older methods, and this is exemplified by a teaching unit comparing two short stories by Nathaniel Hawthorne. Peer conferences and peer editing in the revision stages, which are features of the process model, can lead to…

  19. Clean, Agile Processing Technology.

    DTIC Science & Technology

    1997-12-01

    Research ltr dtd 10 Jun 98 THIS PAGE IS UNCLASSIFIED FINAL REPORT CLEAN, AGILE PROCESSING TECHNOLOGY Contract # N00014-96-C-0139 PI: S. W . Sinton...Agile Processing Technology . T UNCLAS I N Sinton, S. W.IN S REQUIRED FOR (Explain needin detaiO E C This document is requested by the Canadian Department

  20. Polarization Radar Processing Technology

    DTIC Science & Technology

    1989-10-01

    Oi"C FILE ( J qII RADC-TR-89-144 In-House Report October 1989 AD-A215 242 POLARIZATION RADAR PROCESSING TECHNOLOGY Kenneth C. Stiefvater, Russell D...NO. NO. NO. ACCESSION NO. 62702F 4506 11 58 11. TITLE (Include Security Classification) POLARIZATION RADAR PROCESSING TECHNOLOGY 12. PERSONAL AUTHOR(S

  1. Kuhlthau's Information Search Process.

    ERIC Educational Resources Information Center

    Shannon, Donna

    2002-01-01

    Explains Kuhlthau's Information Search Process (ISP) model which is based on a constructivist view of learning and provides a framework for school library media specialists for the design of information services and instruction. Highlights include a shift from library skills to information skills; attitudes; process approach; and an interview with…

  2. Monitoring Process Effectiveness

    EPA Science Inventory

    Treatment of municipal sludges to produce biosolids which meet federal and/or state requirements for land application requires process monitoring. The goal of process monitoring is to produce biosolids of consistent and reliable quality. In its simplest form, for Class B treatme...

  3. Processing of plastics

    PubMed Central

    Spaak, Albert

    1975-01-01

    An overview is given of the processing of plastic materials from the handling of polymers in the pellet and powder form to manufacturing of a plastic fabricated product. Various types of equipment used and melt processing ranges of various polymer formulations to make the myriad of plastic products that are commercially available are discussed. PMID:1175556

  4. Sentences as Biological Processes.

    ERIC Educational Resources Information Center

    McNeil, David

    A study of the speech process was conducted. The process is described as one closely linked to the one involved in the problem of the serial order in behavior. It is pointed out that in the speech of young children the grammatical relations that are properties of elementary underlying sentences appear in the grammatical meanings. Six examples of…

  5. Electron-attachment processes

    NASA Astrophysics Data System (ADS)

    Christophorou, L. G.; McCorkle, D. L.; Christodoulides, A. A.

    Topics covered include: modes of production of negative ions, techniques for the study of electron attachment processes, dissociative electron attachment to ground state molecules, dissociative electron attachment to hot molecules (effects of temperature on dissociative electron attachment), molecular parent negative ions, and negative ions formed by ion pair processes and by collisions of molecules with ground state and Rydberg atoms.

  6. Integrated Optical Information Processing

    DTIC Science & Technology

    1988-08-01

    dimensional processing to be performed with inherently one-dimensional signal processing devices. This permits the monolithic or hybrid integration of...effective time delays; 5. Selective partial waveguide outcoupling of channelized light from an integrated optical chip; 6. Potential monolithic ... integrated optical chip; 6. Potential monolithic integration of optical waveguides with two-dimensional opto- electronic detector technology. The integrated

  7. Shell Higher Olefins Process.

    ERIC Educational Resources Information Center

    Lutz, E. F.

    1986-01-01

    Shows how olefin isomerization and the exotic olefin metathesis reaction can be harnessed in industrial processes. Indicates that the Shell Higher Olefins Process makes use of organometallic catalysts to manufacture alpha-olefins and internal carbon-11 through carbon-14 alkenes in a flexible fashion that can be adjusted to market needs. (JN)

  8. Microwave processing of ceramics

    SciTech Connect

    Katz, J.D.

    1993-01-01

    Recent work in the areas of microwave processing and joining of ceramics is briefly reviewed. Advantages and disadvantages of microwave processing as well as some of the current issues in the field are discussed. Current state and potential for future commercialization of this technology is also addressed.

  9. Microwave processing of ceramics

    SciTech Connect

    Katz, J.D.

    1993-04-01

    Recent work in the areas of microwave processing and joining of ceramics is briefly reviewed. Advantages and disadvantages of microwave processing as well as some of the current issues in the field are discussed. Current state and potential for future commercialization of this technology is also addressed.

  10. Interception processes during snowstorms

    Treesearch

    David H. Miller

    1964-01-01

    Four processes are identified as determining the initial interception of falling snow by forest during storms: delivery of snow particles from the airstream to the forest; true throughfall of particles to the forest floor; impaction and adhesion of particles to foliage and branches; and cohesion of particles into masses of snow. Delivery and impaction processes seem...

  11. Microsystem process networks

    DOEpatents

    Wegeng, Robert S.; TeGrotenhuis, Ward E.; Whyatt, Greg A.

    2007-09-18

    Various aspects and applications of microsystem process networks are described. The design of many types of Microsystems can be improved by ortho-cascading mass, heat, or other unit process operations. Microsystems having energetically efficient microchannel heat exchangers are also described. Detailed descriptions of numerous design features in microcomponent systems are also provided.

  12. Microsystem process networks

    DOEpatents

    Wegeng, Robert S.; TeGrotenhuis, Ward E.; Whyatt, Greg A.

    2006-10-24

    Various aspects and applications of microsystem process networks are described. The design of many types of microsystems can be improved by ortho-cascading mass, heat, or other unit process operations. Microsystems having exergetically efficient microchannel heat exchangers are also described. Detailed descriptions of numerous design features in microcomponent systems are also provided.

  13. Microsystem process networks

    DOEpatents

    Wegeng, Robert S [Richland, WA; TeGrotenhuis, Ward E [Kennewick, WA; Whyatt, Greg A [West Richland, WA

    2010-01-26

    Various aspects and applications or microsystem process networks are described. The design of many types of microsystems can be improved by ortho-cascading mass, heat, or other unit process operations. Microsystems having energetically efficient microchannel heat exchangers are also described. Detailed descriptions of numerous design features in microcomponent systems are also provided.

  14. Relational Processing Following Stroke

    ERIC Educational Resources Information Center

    Andrews, Glenda; Halford, Graeme S.; Shum, David; Maujean, Annick; Chappell, Mark; Birney, Damian

    2013-01-01

    The research examined relational processing following stroke. Stroke patients (14 with frontal, 30 with non-frontal lesions) and 41 matched controls completed four relational processing tasks: sentence comprehension, Latin square matrix completion, modified Dimensional Change Card Sorting, and n-back. Each task included items at two or three…

  15. HEPA filter dissolution process

    SciTech Connect

    Brewer, K.N.; Murphy, J.A.

    1992-12-31

    This invention is comprised of a process for dissolution of spent high efficiency particulate air (HEPA) filters and then combining the complexed filter solution with other radioactive wastes prior to calcining the mixed and blended waste feed. The process is an alternate to a prior method of acid leaching the spent filters which is an inefficient method of treating spent HEPA filters for disposal.

  16. How hummus is processed

    USDA-ARS?s Scientific Manuscript database

    This month’s column will continue the theme of “How Is It Processed?” The food to be discussed this month is hummus. Hummus is known for its healthfulness. This column will provide a brief overview of the history of hummus and the current market. It will also unveil hummus processing techniques....

  17. A Textbook Selection Process.

    ERIC Educational Resources Information Center

    Prosser, Daniel R.; Bondavalli, Bonnie J.

    In response to the problem facing college faculties of choosing textbooks that are both "readable" by students and adequate in content coverage, a text selection process has been developed that can be used with or without the aid of a reading specialist. The first step in the process, a preliminary check, examines each proposed text's publication…

  18. Basic Data Processing.

    ERIC Educational Resources Information Center

    Scalice, John J.

    This study guide in data processing is designed to make the subject accessible to the secondary student. It contains the following units: Historical Developments, Understanding the Computer, Careers in Data Processing, The Tabulating Card, Keypunching, Interpreting, Sorting, The 514 Reproducer, The 85 Collator, and The 402 Accounting Machine. The…

  19. Cognitive Processes and Achievement.

    ERIC Educational Resources Information Center

    Hunt, Dennis; Randhawa, Bikkar S.

    For a group of 165 fourth- and fifth-grade students, four achievement test scores were correlated with success on nine tests designed to measure three cognitive functions: sustained attention, successive processing, and simultaneous processing. This experiment was designed in accordance with Luria's model of the three functional units of the…

  20. Food-Processing Wastes.

    PubMed

    Frenkel, Val S; Cummings, Gregg A; Maillacheruvu, K Y; Tang, Walter Z

    2016-10-01

    Literature published in 2015 and early 2016 related to food processing wastes treatment for industrial applications are reviewed. This review is a subsection of the Treatment Systems section of the annual Water Environment Federation literature review and covers the following food processing industries and applications: general, meat and poultry, fruits and vegetables, dairy and beverage, and miscellaneous treatment of food wastes.

  1. Shell Higher Olefins Process.

    ERIC Educational Resources Information Center

    Lutz, E. F.

    1986-01-01

    Shows how olefin isomerization and the exotic olefin metathesis reaction can be harnessed in industrial processes. Indicates that the Shell Higher Olefins Process makes use of organometallic catalysts to manufacture alpha-olefins and internal carbon-11 through carbon-14 alkenes in a flexible fashion that can be adjusted to market needs. (JN)

  2. In Situ Processing.

    ERIC Educational Resources Information Center

    Edgar, T. F.; Schechter, R. S.

    1980-01-01

    Describes research on in situ processing to develop necessary theory and understanding of the underground process to facilitate commercialization of a wide range of mineral deposits. Goal is to produce laboratory and computer-based tools to allow site evaluation based on field and laboratory measurements of mineral and associated overburdens.…

  3. Streamlining the EIS Process

    ERIC Educational Resources Information Center

    Josephson, Julian

    1977-01-01

    A new publication service abstracts, indexes, and prepares microfiche of environmental impact statements (EIS). This new service is designed to streamline the EIS process by reducing the cost and time of preparation, by eliminating redundancy of similar statements, and by working with the government to standardize the preparation process. (MA)

  4. Mineral Processing Technology Roadmap

    SciTech Connect

    none,

    2000-09-01

    This document represents the roadmap for Processing Technology Research in the US Mining Industry. It was developed based on the results of a Processing Technology Roadmap Workshop sponsored by the National Mining Association in conjunction with the US Department of Energy, Office of Energy Efficiency and Renewable Energy, Office of Industrial Technologies. The Workshop was held January 24 - 25, 2000.

  5. Associative list processing unit

    DOEpatents

    Hemmert, Karl Scott; Underwood, Keith D.

    2013-01-29

    An associative list processing unit and method comprising employing a plurality of prioritized cell blocks and permitting inserts to occur in a single clock cycle if all of the cell blocks are not full. Also, an associative list processing unit and method comprising employing a plurality of prioritized cell blocks and using a tree of prioritized multiplexers descending from the plurality of cell blocks.

  6. Process, Product, and Playmaking

    ERIC Educational Resources Information Center

    Fisher, Maisha T.; Purcell, Susie Spear; May, Rachel

    2009-01-01

    This article examines relationships among process, product, and playmaking in a southeastern playwriting and performance program for teen girls, Playmaking for Girls (PFG). The authors have chosen to focus on tensions between process and product. Such tensions are present in the challenges teachers experience when privileging student-centered…

  7. A Textbook Selection Process.

    ERIC Educational Resources Information Center

    Prosser, Daniel R.; Bondavalli, Bonnie J.

    In response to the problem facing college faculties of choosing textbooks that are both "readable" by students and adequate in content coverage, a text selection process has been developed that can be used with or without the aid of a reading specialist. The first step in the process, a preliminary check, examines each proposed text's publication…

  8. Processes in Reading Comprehension.

    ERIC Educational Resources Information Center

    Ransom, Grayce A.

    This examination of the processes in reading comprehension is divided into seven categories. "Theoretical Foundations" reviews some of the research conducted by Bruner, Piaget, and Bloom in the areas of cognition or comprehension processes of young children. "Development of a Spiraling Reading Curriculum" examines a spiraling taxonomy of reading…

  9. Relational Processing Following Stroke

    ERIC Educational Resources Information Center

    Andrews, Glenda; Halford, Graeme S.; Shum, David; Maujean, Annick; Chappell, Mark; Birney, Damian

    2013-01-01

    The research examined relational processing following stroke. Stroke patients (14 with frontal, 30 with non-frontal lesions) and 41 matched controls completed four relational processing tasks: sentence comprehension, Latin square matrix completion, modified Dimensional Change Card Sorting, and n-back. Each task included items at two or three…

  10. Silicon production process evaluations

    NASA Technical Reports Server (NTRS)

    1981-01-01

    Chemical engineering analysis of the HSC process (Hemlock Semiconductor Corporation) for producing silicon from dichlorosilane in a 1,000 MT/yr plant was continued. Progress and status for the chemical engineering analysis of the HSC process are reported for the primary process design engineering activities: base case conditions (85%), reaction chemistry (85%), process flow diagram (60%), material balance (60%), energy balance (30%), property data (30%), equipment design (20%) and major equipment list (10%). Engineering design of the initial distillation column (D-01, stripper column) in the process was initiated. The function of the distillation column is to remove volatile gases (such as hydrogen and nitrogen) which are dissolved in liquid chlorosilanes. Initial specifications and results for the distillation column design are reported including the variation of tray requirements (equilibrium stages) with reflux ratio for the distillation.

  11. Economics of polysilicon processes

    NASA Technical Reports Server (NTRS)

    Yaws, C. L.; Li, K. Y.; Chou, S. M.

    1986-01-01

    Techniques are being developed to provide lower cost polysilicon material for solar cells. Existing technology which normally provides semiconductor industry polysilicon material is undergoing changes and also being used to provide polysilicon material for solar cells. Economics of new and existing technologies are presented for producing polysilicon. The economics are primarily based on the preliminary process design of a plant producing 1,000 metric tons/year of silicon. The polysilicon processes include: Siemen's process (hydrogen reduction of trichlorosilane); Union Carbide process (silane decomposition); and Hemlock Semiconductor process (hydrogen reduction of dichlorosilane). The economics include cost estimates of capital investment and product cost to produce polysilicon via the technology. Sensitivity analysis results are also presented to disclose the effect of major paramentes such as utilities, labor, raw materials and capital investment.

  12. Formed HIP Can Processing

    SciTech Connect

    Clarke, Kester Diederik

    2015-07-27

    The intent of this report is to document a procedure used at LANL for HIP bonding aluminum cladding to U-10Mo fuel foils using a formed HIP can for the Domestic Reactor Conversion program in the NNSA Office of Material, Management and Minimization, and provide some details that may not have been published elsewhere. The HIP process is based on the procedures that have been used to develop the formed HIP can process, including the baseline process developed at Idaho National Laboratory (INL). The HIP bonding cladding process development is summarized in the listed references. Further iterations with Babcock & Wilcox (B&W) to refine the process to meet production and facility requirements is expected.

  13. Spacelab Data Processing Facility

    NASA Technical Reports Server (NTRS)

    1983-01-01

    The Spacelab Data Processing Facility (SDPF) processes, monitors, and accounts for the payload data from Spacelab and other Shuttle missions and forwards relevant data to various user facilities worldwide. The SLDPF is divided into the Spacelab Input Processing System (SIPS) and the Spacelab Output Processing System (SOPS). The SIPS division demultiplexes, synchronizes, time tags, quality checks, accounts for the data, and formats the data onto tapes. The SOPS division further edits, blocks, formats, and records the data on tape for shipment to users. User experiments must conform to the Spacelab's onboard High Rate Multiplexer (HRM) format for maximum process ability. Audio, analog, instrumentation, high density, experiment data, input/output data, quality control and accounting, and experimental channel tapes along with a variety of spacelab ancillary tapes are provided to the user by SLDPF.

  14. Materials processing in space

    NASA Technical Reports Server (NTRS)

    Waldron, R. D.; Criswell, D. R.

    1982-01-01

    Processing-refining of raw materials from extraterrestrial sources is detailed for a space materials handling facility. The discussion is constrained to those steps necessary to separate desired components from raw or altered input ores, semi-purified feedstocks, or process scrap and convert the material into elements, alloys, and consumables. The materials are regarded as originating from dead satellites and boosters, lunar materials, and asteroids. Strong attention will be given to recycling reagent substances to avoid the necessity of transporting replacements. It is assumed that since no aqueous processes exist on the moon, the distribution of minerals will be homogeneous. The processing-refining scenario will include hydrochemical, pyrochemical, electrochemical, and physical techniques selected for the output mass rate/unit plant mass ratio. Flow charts of the various materials processing operations which could be performed with lunar materials are provided, noting the necessity of delivering several alloying elements from the earth due to scarcities on the moon.

  15. Elemental sulfur recovery process

    DOEpatents

    Flytzani-Stephanopoulos, Maria; Hu, Zhicheng

    1993-01-01

    An improved catalytic reduction process for the direct recovery of elemental sulfur from various SO.sub.2 -containing industrial gas streams. The catalytic process provides combined high activity and selectivity for the reduction of SO.sub.2 to elemental sulfur product with carbon monoxide or other reducing gases. The reaction of sulfur dioxide and reducing gas takes place over certain catalyst formulations based on cerium oxide. The process is a single-stage, catalytic sulfur recovery process in conjunction with regenerators, such as those used in dry, regenerative flue gas desulfurization or other processes, involving direct reduction of the SO.sub.2 in the regenerator off gas stream to elemental sulfur in the presence of a catalyst.

  16. Elemental sulfur recovery process

    DOEpatents

    Flytzani-Stephanopoulos, M.; Zhicheng Hu.

    1993-09-07

    An improved catalytic reduction process for the direct recovery of elemental sulfur from various SO[sub 2]-containing industrial gas streams. The catalytic process provides combined high activity and selectivity for the reduction of SO[sub 2] to elemental sulfur product with carbon monoxide or other reducing gases. The reaction of sulfur dioxide and reducing gas takes place over certain catalyst formulations based on cerium oxide. The process is a single-stage, catalytic sulfur recovery process in conjunction with regenerators, such as those used in dry, regenerative flue gas desulfurization or other processes, involving direct reduction of the SO[sub 2] in the regenerator off gas stream to elemental sulfur in the presence of a catalyst. 4 figures.

  17. Optical signal processing

    NASA Technical Reports Server (NTRS)

    Casasent, D.

    1978-01-01

    The article discusses several optical configurations used for signal processing. Electronic-to-optical transducers are outlined, noting fixed window transducers and moving window acousto-optic transducers. Folded spectrum techniques are considered, with reference to wideband RF signal analysis, fetal electroencephalogram analysis, engine vibration analysis, signal buried in noise, and spatial filtering. Various methods for radar signal processing are described, such as phased-array antennas, the optical processing of phased-array data, pulsed Doppler and FM radar systems, a multichannel one-dimensional optical correlator, correlations with long coded waveforms, and Doppler signal processing. Means for noncoherent optical signal processing are noted, including an optical correlator for speech recognition and a noncoherent optical correlator.

  18. Business Process Management

    NASA Astrophysics Data System (ADS)

    Mendling, Jan

    The recent progress of Business Process Management (BPM) is reflected by the figures of the related industry. Wintergreen Research estimates that the international market for BPM-related software and services accounted for more than USD 1 billion in 2005 with a tendency towards rapid growth in the subsequent couple of years [457]. The relevance of business process modeling to general management initiatives has been previously studied in the 1990s [28]. Today, Gartner finds that organizations that had the best results in implementing business process management spent more than 40 percent of the total project time on discovery and construction of their initial process model [265]. As a consequence, Gartner considers Business Process Modeling to be among the Top 10 Strategic Technologies for 2008.

  19. Low temperature solution processed high-κ ZrO2 gate dielectrics for nanoelectonics

    NASA Astrophysics Data System (ADS)

    Kumar, Arvind; Mondal, Sandip; Rao, K. S. R. Koteswara

    2016-05-01

    The high-κ gate dielectrics, specifically amorphous films offer salient features such as exceptional mechanical flexibility, smooth surfaces and better uniformity associated with low leakage current density. In this work, ∼35 nm thick amorphous ZrO2 films were deposited on silicon substrate at low temperature (300 °C, 1 h) from facile spin-coating method and characterized by various analytical techniques. The X-ray diffraction and X-ray photoelectron spectroscopy reveal the formation of amorphous phase ZrO2, while ellipsometry analysis together with the Atomic Force Microscope suggest the formation of dense film with surface roughness of 1.5 Å, respectively. The fabricated films were integrated in metal-oxide-semiconductor (MOS) structures to check the electrical capabilities. The oxide capacitance (Cox), flat band capacitance (CFB), flat band voltage (VFB), dielectric constant (κ) and oxide trapped charges (Qot) extracted from high frequency (1 MHz) C-V curve are 186 pF, 104 pF, 0.37 V, 15 and 2 × 10-11 C, respectively. The small flat band voltage 0.37 V, narrow hysteresis and very little frequency dispersion between 10 kHz-1 MHz suggest an excellent a-ZrO2/Si interface with very less trapped charges in the oxide. The films exhibit a low leakage current density 4.7 × 10-9 A/cm2 at 1 V. In addition, the charge transport mechanism across the MOSC is analyzed and found to have a strong bias dependence. The space charge limited conduction mechanism is dominant in the high electric field region (1.3-5 V) due to the presence of traps, while the trap-supported tunneling is prevailed in the intermediate region (0.35-1.3 V). Low temperature solution processed ZrO2 thin films obtained are of high quality and find their importance as a potential dielectric layer on Si and polymer based flexible electronics.

  20. EDITORIAL: Industrial Process Tomography

    NASA Astrophysics Data System (ADS)

    Anton Johansen, Geir; Wang, Mi

    2008-09-01

    There has been tremendous development within measurement science and technology over the past couple of decades. New sensor technologies and compact versatile signal recovery electronics are continuously expanding the limits of what can be measured and the accuracy with which this can be done. Miniaturization of sensors and the use of nanotechnology push these limits further. Also, thanks to powerful and cost-effective computer systems, sophisticated measurement and reconstruction algorithms previously only accessible in advanced laboratories are now available for in situ online measurement systems. The process industries increasingly require more process-related information, motivated by key issues such as improved process control, process utilization and process yields, ultimately driven by cost-effectiveness, quality assurance, environmental and safety demands. Industrial process tomography methods have taken advantage of the general progress in measurement science, and aim at providing more information, both quantitatively and qualitatively, on multiphase systems and their dynamics. The typical approach for such systems has been to carry out one local or bulk measurement and assume that this is representative of the whole system. In some cases, this is sufficient. However, there are many complex systems where the component distribution varies continuously and often unpredictably in space and time. The foundation of industrial tomography is to conduct several measurements around the periphery of a multiphase process, and use these measurements to unravel the cross-sectional distribution of the process components in time and space. This information is used in the design and optimization of industrial processes and process equipment, and also to improve the accuracy of multiphase system measurements in general. In this issue we are proud to present a selection of the 145 papers presented at the 5th World Congress on Industrial Process Tomography in Bergen

  1. Guidance on Major Modification Provisions of PSD Rules as Applied to Re-Permitting at Acme Steel Co.

    EPA Pesticide Factsheets

    This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

  2. Detection of mitotic nuclei in breast histopathology images using localized ACM and Random Kitchen Sink based classifier.

    PubMed

    Beevi, K Sabeena; Nair, Madhu S; Bindu, G R

    2016-08-01

    The exact measure of mitotic nuclei is a crucial parameter in breast cancer grading and prognosis. This can be achieved by improving the mitotic detection accuracy by careful design of segmentation and classification techniques. In this paper, segmentation of nuclei from breast histopathology images are carried out by Localized Active Contour Model (LACM) utilizing bio-inspired optimization techniques in the detection stage, in order to handle diffused intensities present along object boundaries. Further, the application of a new optimal machine learning algorithm capable of classifying strong non-linear data such as Random Kitchen Sink (RKS), shows improved classification performance. The proposed method has been tested on Mitosis detection in breast cancer histological images (MITOS) dataset provided for MITOS-ATYPIA CONTEST 2014. The proposed framework achieved 95% recall, 98% precision and 96% F-score.

  3. Ambulatory circadian monitoring (ACM) based on thermometry, motor activity and body position (TAP): a comparison with polysomnography.

    PubMed

    Ortiz-Tudela, Elisabet; Martinez-Nicolas, Antonio; Albares, Javier; Segarra, Francesc; Campos, Manuel; Estivill, Eduard; Rol, Maria Angeles; Madrid, Juan Antonio

    2014-03-14

    An integrated variable based on the combination of wrist Temperature, motor Activity and body Position (TAP) was previously developed at our laboratory to evaluate the functioning of the circadian system and sleep-wake rhythm under ambulatory conditions. However, the reliability of TAP needed to be validated with polysomnography (PSG). 22 subjects suffering from sleep disorders were monitored for one night with a temperature sensor (iButton), an actimeter (HOBO) and exploratory PSG. Mean waveforms, sensitivity (SE), specificity (SP), agreement rates (AR) and comparisons between TAP and sleep stages were studied. The TAP variable was optimized for SE, SP and AR with respect to each individual variable (SE: 92%; SP: 78%; AR: 86%). These results improved upon estimates previously published for actigraphy. Furthermore, TAP values tended to decrease as sleep depth increased, reaching the lowest point at phase 3. Finally, TAP estimates for sleep latency (SL: 37±9 min), total sleep time (TST: 367±13 min), sleep efficiency (SE: 86.8±1.9%) and number of awakenings (NA>5 min: 3.3±.4) were not significantly different from those obtained with PSG (SL: 29±4 min; SE: 89.9±1.8%; NA>5 min: 2.3±.4), despite the heterogeneity of the sleep pathologies monitored. The TAP variable is a novel measurement for evaluating circadian system status and sleep-wake rhythms with a level of reliability better to that of actigraphy. Furthermore, it allows the evaluation of a patient's sleep-wake rhythm in his/her normal home environment, and at a much lower cost than PSG. Future studies in specific pathologies would verify the relevance of TAP in those conditions.

  4. ARM-ACME V: ARM Airborne Carbon Measurements V on the North Slope of Alaska Field Campaign Report

    SciTech Connect

    Biraud, Sebastien C

    2016-05-01

    Atmospheric temperatures are warming faster in the Arctic than predicted by climate models. The impact of this warming on permafrost degradation is not well understood, but it is projected to increase carbon decomposition and greenhouse gas production (CO2 and/or CH4) by arctic ecosystems. Airborne observations of atmospheric trace gases, aerosols and cloud properties in North Slopes of Alaska (NSA) are improving our understanding of global climate, with the goal of reducing the uncertainty in global and regional climate simulations and projections. From June 1 through September 15, 2015, AAF deployed the G1 research aircraft and flew over the North Slope of Alaska (38 flights, 140 science flight hours), with occasional vertical profiling over Prudhoe Bay, Oliktok point, Barrow, Atqasuk, Ivotuk, and Toolik Lake. The aircraft payload included Picarro and Los Gatos Research (LGR) analyzers for continuous measurements of CO2, CH4, H2O, and CO and N2O mixing ratios, and a 12-flask sampler for analysis of carbon cycle gases (CO2, CO, CH4, N2O, 13CO2, and trace hydrocarbon species). The aircraft payload also include measurements of aerosol properties (number size distribution, total number concentration, absorption, and scattering), cloud properties (droplet and ice size information), atmospheric thermodynamic state, and solar/infrared radiation.

  5. ARM-ACME V: ARM Airborne Carbon Measurements V on the North Slope of Alaska Science and Implementation Plan

    SciTech Connect

    Biraud, S

    2015-05-01

    Atmospheric temperatures are warming faster in the Arctic than predicted by climate models. The impact of this warming on permafrost degradation is not well understood, but it is projected to increase carbon decomposition and greenhouse gas production (CO₂ and/or CH₄) by arctic ecosystems. Airborne observations of atmospheric trace gases, aerosols, and cloud properties at the North Slope of Alaska are improving our understanding of global climate, with the goal of reducing the uncertainty in global and regional climate simulations and projections.

  6. Pathfinder Lander Rover Recharge System, and MARCO POLO Controls and ACME Regolith Feed System Controls and Integration

    NASA Technical Reports Server (NTRS)

    Tran, Sarah Diem

    2015-01-01

    This project stems from the Exploration, Research, and Technology Directorate (UB) Projects Division, and one of their main initiatives is the "Journey to Mars". Landing on the surface of Mars which is millions of miles away is an incredibly large challenge. The terrain is covered in boulders, deep canyons, volcanic mountains, and spotted with sand dunes. The robotic lander is a kind of spacecraft with multiple purposes. One purpose is to be the protective shell for the Martian rover and absorb the impact from the landing forces; another purpose is to be a place where the rovers can come back to, actively communicate with, and recharge their batteries from. Rovers have been instrumental to the Journey to Mars initiative. They have been performing key research on the terrain of the red planet, trying to unlock the mysteries of the land for over a decade. The rovers that will need charging will not all have the same kind of internal battery either. RASSOR batteries may differ from the PbAC batteries inside Red Rover's chassis. NASA has invested heavily in the exploration of the surface of Mars. A driving force behind further exploration is the need for a more efficient operation of Martian rovers. One way is to reduce the weight as much as possible to reduce power consumption given the same mission parameters. In order to reduce the mass of the rovers, power generation, communication, and sample analysis systems currently onboard Martian rovers can be moved to a stationary lander deck. Positioning these systems from the rover to the Lander deck allows a taskforce of smaller, lighter rovers to perform the same tasks currently performed by or planned for larger rovers. A major task in transferring these systems to a stationary lander deck is ensuring that power can be transferred to the rovers.

  7. ACM SIGPLAN Workshop on ML and Its Applications Held in San Francisco, California on June 20-21, 1992

    DTIC Science & Technology

    1992-06-01

    University of Copenhagen Aooession For NTIS GIZA&I • DTIC TAB [ D’ic tj •-’ :2-Cr= D 8 Unarnounced C1 Di tiicut Avall an4tor Dist Special Foreword The...Consistency-Preserving Programs in Distributed ML Clifford D . Krumvieda (Cornell University) .................................... 157 Implementing ML on...some implementations of SML [App90], the representation of the datatype defined by datatype d = A I B of t, depends on the representation of t. If the

  8. Guidance on Major Modification Provisions of PSD Rules as Applied to Re-Permitting at Acme Steel Co.

    EPA Pesticide Factsheets

    This document may be of assistance in applying the Title V air operating permit regulations. This document is part of the Title V Policy and Guidance Database available at www2.epa.gov/title-v-operating-permits/title-v-operating-permit-policy-and-guidance-document-index. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

  9. Radiology interpretation process modeling.

    PubMed

    Noumeir, Rita

    2006-04-01

    Information and communication technology in healthcare promises optimized patient care while ensuring efficiency and cost-effectiveness. However, the promised results are not yet achieved; the healthcare process requires analysis and radical redesign to achieve improvements in care quality and productivity. Healthcare process reengineering is thus necessary and involves modeling its workflow. Even though the healthcare process is very large and not very well modeled yet, its sub-processes can be modeled individually, providing fundamental pieces of the whole model. In this paper, we are interested in modeling the radiology interpretation process that results in generating a diagnostic radiology report. This radiology report is an important clinical element of the patient healthcare record and assists in healthcare decisions. We present the radiology interpretation process by identifying its boundaries and by positioning it on the large healthcare process map. Moreover, we discuss an information data model and identify roles, tasks and several information flows. Furthermore, we describe standard frameworks to enable radiology interpretation workflow implementations between heterogeneous systems.

  10. Process measurement assurance program

    SciTech Connect

    Pettit, R.B.

    1996-05-01

    This paper describes a new method for determining, improving, and controlling the measurement process errors (or measurement uncertainty) of a measurement system used to monitor product as it is manufactured. The method is called the Process Measurement Assurance Program (PMAP). It integrates metrology early into the product realization process and is a step beyond statistical process control (SPC), which monitors only the product. In this method, a control standard is used to continuously monitor the status of the measurement system. Analysis of the control standard data allow the determination of the measurement error inherent in the product data and allow one to separate the variability in the manufacturing process from variability in the measurement process. These errors can be then associated with either the measurement equipment, variability of the measurement process, operator bias, or local environmental effects. Another goal of PMAP is to determine appropriate re-calibration intervals for the measurement system, which may be significantly longer or shorter than the interval typically assigned by the calibration organization.

  11. CCD gate definition process

    NASA Astrophysics Data System (ADS)

    Bluzer

    1986-02-01

    The present invention utilizes a double masking step in a CCD gate definition process to eliminate the re-entrant oxide by using a thin film layer other than photoresist to define the polysilicon gates used by defining the thin film layer with a double masking process before any of the polysilicon gate layer is etched. It is one object of the present invention, therefore, to provide an improved process for CCD gate definition. It is another object of the invention to provide an improved CCD gate definition process wherein a profiled oxide layer is produced over a polysilicon layer without re-entrant oxide regions. It is another object of the invention to provide an improved CCD gate definition process wherein a thin film layer is utilized to define the polysilicon gate layers. It is another object of the invention to provide an improved CCD gate definition process wherein the thin film layer is defined by a double masking process before any polysilicon layer is etched.

  12. Processes in Lingua Cosmica

    NASA Astrophysics Data System (ADS)

    Ollongren, Alexander

    2012-02-01

    In a sequence of papers on the topic of message construction for interstellar communication by means of a cosmic language, representations of various kinds of concepts of reality in a Lingua Cosmica system [1]. Those studied were logic relations of a static character. The present contribution contains an important, fundamental extension: groundwork is done for the purpose of interpreting (dynamic) proc esses of various sorts in the linguistic system. Individual processes are abstracted in a logic sense and provided with basic properties as termination and communication functions. They can be combined into kinds of processes: sequential and parallel ones represented by only one inductive definition in logic. Based on concepts from the so-called process algebra, processes are provided with channel s mapping them to their states. State vectors are introduced to represent states of conglomerates of processes. Communication between processes (locally or globally) is effectuated by means of state transitions. Together with a programmed arb itration function, state vectors play a crucial role in representing communication. With these ingredients possibilities for general interpretations of a wide range of processes in the Lingua Cosmica system come in view.

  13. Asbestos release from whole-building demolition of buildings with asbestos-containing material.

    PubMed

    Perkins, Robert A; Hargesheimer, John; Fourie, Walter

    2007-12-01

    The whole-building demolition method, which entails one-or two-story buildings pushed down by heavy equipment, loaded into trucks, and hauled away, is generally the most cost-effective means to remove small buildings. For taller buildings, a crane and wrecking ball may be used initially to reduce the height of the building. Demolitions might release asbestos fibers from friable asbestos-containing material (ACM). Fibers also might be released from nominally nonfriable ACM (Categories I and II nonfriable ACM) if it becomes friable after rough handling throughout the whole-building demolition process. This paper reports on asbestos air monitoring from two demolition projects involving ACM. In one building, Category II nonfriable ACM was present because it could not be removed safely prior to demolition. Both projects had large quantities of gypsum wallboard with ACM joint compound and ACM flooring. One building had large quantities of ACM spray-on ceiling material. During the demolitions personal air monitoring of the workers and area air monitoring downwind and around the sites were conducted. The monitoring found the concentrations of fibers detected by phase contrast microscopy were generally well below the permissible exposure limits (PEL) of workers. Electron microcopy analysis of samples at or near the PEL indicated most of the fibers were not asbestos, and the actual asbestos exposure was often below the detection limit of the procedure. The buildings were kept wet with fire hoses during the demolition and that required large quantities of water, 20,000-60,000 gal/day (75-225 m(3)/day). Earlier studies found little asbestos release from buildings containing only nonfriable ACM demolished by this method. This project found a negligible release of asbestos fibers, despite the presence of nonfriable materials that might become friable, such as ACM joint compound and spray-on ACM ceiling coating.

  14. Advanced Hydrogen Liquefaction Process

    SciTech Connect

    Schwartz, Joseph; Kromer, Brian; Neu, Ben; Jankowiak, Jerome; Barrett, Philip; Drnevich, Raymond

    2011-09-28

    The project identified and quantified ways to reduce the cost of hydrogen liquefaction, and reduce the cost of hydrogen distribution. The goal was to reduce the power consumption by 20% and then to reduce the capital cost. Optimizing the process, improving process equipment, and improving ortho-para conversion significantly reduced the power consumption of liquefaction, but by less than 20%. Because the efficiency improvement was less than the target, the program was stopped before the capital cost was addressed. These efficiency improvements could provide a benefit to the public to improve the design of future hydrogen liquefiers. The project increased the understanding of hydrogen liquefaction by modeling different processes and thoroughly examining ortho-para separation and conversion. The process modeling provided a benefit to the public because the project incorporated para hydrogen into the process modeling software, so liquefaction processes can be modeled more accurately than using only normal hydrogen. Adding catalyst to the first heat exchanger, a simple method to reduce liquefaction power, was identified, analyzed, and quantified. The demonstrated performance of ortho-para separation is sufficient for at least one identified process concept to show reduced power cost when compared to hydrogen liquefaction processes using conventional ortho-para conversion. The impact of improved ortho-para conversion can be significant because ortho para conversion uses about 20-25% of the total liquefaction power, but performance improvement is necessary to realize a substantial benefit. Most of the energy used in liquefaction is for gas compression. Improvements in hydrogen compression will have a significant impact on overall liquefier efficiency. Improvements to turbines, heat exchangers, and other process equipment will have less impact.

  15. The VISAR Process

    NASA Technical Reports Server (NTRS)

    Hathaway, David; Meyer, Paul; Templeton, Gary F.

    2003-01-01

    The Video Image Stabilization And Registration (VISAR) process is an award winning video image processing software developed at NASA's Marshall Space Flight Center. VISAR has a wide variety of application areas where the refinement of digital video is needed. It is used to correct jitter, rotation, and zoom effects by registering and processing on individual image captures that are a part of normal video capturing. Its most prominent uses were the 1996 Olympic Bombing case and in identifying Saddam Hussein during the Iraq war. Based on first-hand knowledge, this paper describes the VISAR process, which consists of several steps designed to refine digital video using VISAR software. The process determines the differences between two video images so that one, or both, of the images can be changed in ways that make them match as well as possible. Corrections include changes in position (horizontal and vertical image shifts), changes in orientation (image rotation), and changes in magnification (image zoom). While much of the VISAR process is automated, in its current embodiment it requires the user to initially identify the area of interest and to reset a threshold parameter if the default gives unacceptable results. The basic process that is used is an old tried and true method that determines how well the two images match. This process is called cross-correlation. It gives a single number, the correlation coefficient, that is equal to 1.0 if the images are perfectly matched, is equal to 0.0 if the images have nothing in common, and is equal to -1.0 if one image is the negative of the other. This basic process is used by many image stabilization methods. With VISAR we use it in a manner that provides statistical information needed to best determine orientation and magnification.

  16. The VISAR Process

    NASA Technical Reports Server (NTRS)

    Hathaway, David; Meyer, Paul; Templeton, Gary F.

    2003-01-01

    The Video Image Stabilization And Registration (VISAR) process is an award winning video image processing software developed at NASA's Marshall Space Flight Center. VISAR has a wide variety of application areas where the refinement of digital video is needed. It is used to correct jitter, rotation, and zoom effects by registering and processing on individual image captures that are a part of normal video capturing. Its most prominent uses were the 1996 Olympic Bombing case and in identifying Saddam Hussein during the Iraq war. Based on first-hand knowledge, this paper describes the VISAR process, which consists of several steps designed to refine digital video using VISAR software. The process determines the differences between two video images so that one, or both, of the images can be changed in ways that make them match as well as possible. Corrections include changes in position (horizontal and vertical image shifts), changes in orientation (image rotation), and changes in magnification (image zoom). While much of the VISAR process is automated, in its current embodiment it requires the user to initially identify the area of interest and to reset a threshold parameter if the default gives unacceptable results. The basic process that is used is an old tried and true method that determines how well the two images match. This process is called cross-correlation. It gives a single number, the correlation coefficient, that is equal to 1.0 if the images are perfectly matched, is equal to 0.0 if the images have nothing in common, and is equal to -1.0 if one image is the negative of the other. This basic process is used by many image stabilization methods. With VISAR we use it in a manner that provides statistical information needed to best determine orientation and magnification.

  17. Membrane separation processes

    SciTech Connect

    Rautenbach, R.; Albrecht, R.

    1989-01-01

    The success of two membrane processes, reverse osmosis and ultrafiltration, has helped make membrane processes a central technique in solving separation problems for fluid systems. This book discusses the various applications and developments in membrane technology and shows how accurate membrane processes can be designed. Starting with the local transport phenomena, the behavior of individual elements such as tube or plate membrane and the behavior of the technical unit - the module - are discussed in detail. The book goes on to demonstrate the most effective ways of arranging modules for forming an optimal plant.

  18. Information processing during phagocytosis

    PubMed Central

    Underhill, David M.; Goodridge, Helen S.

    2017-01-01

    Phagocytosis, the process by which macrophages, dendritic cells and other myeloid phagocytes internalize diverse particulate targets, is a key mechanism of innate immunity. The molecular and cellular events underlying the binding and engulfment of targets in phagosomes have been extensively studied. More recent data suggest that the process of phagocytosis itself provides information to myeloid phagocytes about the nature of the targets they are eating and that this helps tailor inflammatory responses. In this Review, we discuss how such information is acquired during phagocytosis, and how it is processed to coordinate an immune response. PMID:22699831

  19. Neural Analog Information Processing

    NASA Astrophysics Data System (ADS)

    Hecht-Nielsen, Robert

    1982-07-01

    Neural Analog Information Processing (NAIP) is an effort to develop general purpose pattern classification architectures based upon biological information processing principles. This paper gives an overview of NAIP and its relationship to the previous work in neural modeling from which its fundamental principles are derived. It also presents a theorem concerning the stability of response of a slab (a two dimensional array of identical simple processing units) to time-invariant (spatial) patterns. An experiment (via computer emulation) demonstrating classification of a spatial pattern by a simple, but complete NAIP architecture is described. A concept for hardware implementation of NAIP architectures is briefly discussed.

  20. Mechanical processes in biochemistry.

    PubMed

    Bustamante, Carlos; Chemla, Yann R; Forde, Nancy R; Izhaky, David

    2004-01-01

    Mechanical processes are involved in nearly every facet of the cell cycle. Mechanical forces are generated in the cell during processes as diverse as chromosomal segregation, replication, transcription, translation, translocation of proteins across membranes, cell locomotion, and catalyzed protein and nucleic acid folding and unfolding, among others. Because force is a product of all these reactions, biochemists are beginning to directly apply external forces to these processes to alter the extent or even the fate of these reactions hoping to reveal their underlying molecular mechanisms. This review provides the conceptual framework to understand the role of mechanical force in biochemistry.

  1. Coal liquefaction quenching process

    DOEpatents

    Thorogood, Robert M.; Yeh, Chung-Liang; Donath, Ernest E.

    1983-01-01

    There is described an improved coal liquefaction quenching process which prevents the formation of coke with a minimum reduction of thermal efficiency of the coal liquefaction process. In the process, the rapid cooling of the liquid/solid products of the coal liquefaction reaction is performed without the cooling of the associated vapor stream to thereby prevent formation of coke and the occurrence of retrograde reactions. The rapid cooling is achieved by recycling a subcooled portion of the liquid/solid mixture to the lower section of a phase separator that separates the vapor from the liquid/solid products leaving the coal reactor.

  2. Chemical Processing Manual

    NASA Technical Reports Server (NTRS)

    Beyerle, F. J.

    1972-01-01

    Chemical processes presented in this document include cleaning, pickling, surface finishes, chemical milling, plating, dry film lubricants, and polishing. All types of chemical processes applicable to aluminum, for example, are to be found in the aluminum alloy section. There is a separate section for each category of metallic alloy plus a section for non-metals, such as plastics. The refractories, super-alloys and titanium, are prime candidates for the space shuttle, therefore, the chemical processes applicable to these alloys are contained in individual sections of this manual.

  3. Troubleshooting refinery processes

    SciTech Connect

    Lieberman, N.P.

    1981-01-01

    A reference guide that is designed to help petroleum refinery process engineers to locate and solve refinery problems is presented. At the end of each chapter a troubleshooting guide is presented, outlining possible causes of the problem and solutions. The contents include: crude unit; delayed coking cycles; delayed coking process; amine regeneration and scrubbing; sulfur recovery; alkylation; saving energy at reduced feed rates; refrigeration systems; centrifugal pumps; distillation towers; vacuum towers; treating liquid hydrocarbons; process heaters; water coolers; alarms and trips; unstable gas plant operations; fouled trays; dehydrating light ends towers; vapor-liquid separation; refinery metallurgy; unusual noises and vibrations; planning performance tests; and control board instruments. (JMT)

  4. Carbon wastewater treatment process

    NASA Technical Reports Server (NTRS)

    Humphrey, M. F.; Simmons, G. M.; Dowler, W. L.

    1974-01-01

    A new powdered-carbon treatment process is being developed for the elimination of the present problems, associated with the disposal of biologically active sewage waste solids, and with water reuse. This counter-current flow process produces an activated carbon, which is obtained from the pyrolysis of the sewage solids, and utilizes this material to remove the adulterating materials from the water. Additional advantages of the process are the elimination of odors, the removal of heavy metals, and the potential for energy conservation.

  5. Municipal waste processing apparatus

    DOEpatents

    Mayberry, J.L.

    1988-04-13

    This invention relates to apparatus for processing municipal waste, and more particularly to vibrating mesh screen conveyor systems for removing grit, glass, and other noncombustible materials from dry municipal waste. Municipal waste must be properly processed and disposed of so that it does not create health risks to the community. Generally, municipal waste, which may be collected in garbage trucks, dumpsters, or the like, is deposited in processing areas such as landfills. Land and environmental controls imposed on landfill operators by governmental bodies have increased in recent years, however, making landfill disposal of solid waste materials more expensive. 6 figs.

  6. Advances in metals processing

    NASA Technical Reports Server (NTRS)

    Bales, T. T.; Royster, D. M.

    1982-01-01

    Research on metals processing being conducted to develop improved forming and joining methods with the potential of reducing the weight and cost of future aerospace structures is discussed. The approach followed is to assess the state of the art for fabricating a given structural system, define candidate methods for improving processing, evaluate the merits of each, fabricate and test subelement components, and then scale up the process to demonstrate validity. The development and the state of the art of weldbrazing, superplastic forming (SPF), superplastic forming and codiffusion bonding and superplastic forming and weldbrazing for titanium and the SPF of aluminum is discussed.

  7. Robot welding process control

    NASA Technical Reports Server (NTRS)

    Romine, Peter L.

    1991-01-01

    This final report documents the development and installation of software and hardware for Robotic Welding Process Control. Primary emphasis is on serial communications between the CYRO 750 robotic welder, Heurikon minicomputer running Hunter & Ready VRTX, and an IBM PC/AT, for offline programming and control and closed-loop welding control. The requirements for completion of the implementation of the Rocketdyne weld tracking control are discussed. The procedure for downloading programs from the Intergraph, over the network, is discussed. Conclusions are made on the results of this task, and recommendations are made for efficient implementation of communications, weld process control development, and advanced process control procedures using the Heurikon.

  8. Precision Heating Process

    NASA Technical Reports Server (NTRS)

    1992-01-01

    A heat sealing process was developed by SEBRA based on technology that originated in work with NASA's Jet Propulsion Laboratory. The project involved connecting and transferring blood and fluids between sterile plastic containers while maintaining a closed system. SEBRA markets the PIRF Process to manufacturers of medical catheters. It is a precisely controlled method of heating thermoplastic materials in a mold to form or weld catheters and other products. The process offers advantages in fast, precise welding or shape forming of catheters as well as applications in a variety of other industries.

  9. Carbon wastewater treatment process

    NASA Technical Reports Server (NTRS)

    Humphrey, M. F.; Simmons, G. M.; Dowler, W. L.

    1974-01-01

    A new powdered-carbon treatment process is being developed for the elimination of the present problems, associated with the disposal of biologically active sewage waste solids, and with water reuse. This counter-current flow process produces an activated carbon, which is obtained from the pyrolysis of the sewage solids, and utilizes this material to remove the adulterating materials from the water. Additional advantages of the process are the elimination of odors, the removal of heavy metals, and the potential for energy conservation.

  10. Lubricant Coating Process

    NASA Technical Reports Server (NTRS)

    1989-01-01

    "Peen Plating," a NASA developed process for applying molybdenum disulfide, is the key element of Techniblast Co.'s SURFGUARD process for applying high strength solid lubricants. The process requires two machines -- one for cleaning and one for coating. The cleaning step allows the coating to be bonded directly to the substrate to provide a better "anchor." The coating machine applies a half a micron thick coating. Then, a blast gun, using various pressures to vary peening intensities for different applications, fires high velocity "media" -- peening hammers -- ranging from plastic pellets to steel shot. Techniblast was assisted by Rural Enterprises, Inc. Coating service can be performed at either Techniblast's or a customer's facility.

  11. Ultrasonic Processing of Materials

    SciTech Connect

    Meek, Thomas T.; Han, Qingyou; Jian, Xiaogang; Xu, Hanbing

    2005-06-30

    The purpose of this project was to determine the impact of a new breakthrough technology, ultrasonic processing, on various industries, including steel, aluminum, metal casting, and forging. The specific goals of the project were to evaluate core principles and establish quantitative bases for the ultrasonc processing of materials, and to demonstrate key applications in the areas of grain refinement of alloys during solidification and degassing of alloy melts. This study focussed on two classes of materials - aluminum alloys and steels - and demonstrated the application of ultrasonic processing during ingot casting.

  12. Metal finishing and processing

    SciTech Connect

    Enzminger, J.D. )

    1990-06-01

    This article reviews the finishing and processing of metal wastes for land disposal. Topics of discussion include regulatory aspects, heavy metal treatment, cyanide treatment, waste minimization programs and techniques, and sludge treatment.

  13. Log processing systems

    SciTech Connect

    Bowlin, W.P.; Kneer, M.P.; Ballance, J.D.

    1989-11-07

    This patent describes an improvement in a computer controlled processing system for lumber production. It comprises: a computer, a sequence of processing stations for processing a log segment including; an excess material removing station for generating opposed flat side surfaces on the log segment. The flat side surfaces determined by the computer to become sides of boards to be severed from the log segments; a profiling station for forming profiled edges above and below the flat side surfaces to become the side edges of the boards to be severed from the log segment, and a severing station for severing the boards from the log segments, a conveyance means establishing a path of conveyance and having continuous control of the log segment on conveying the log segment along the path and through the above defined sequence of processing stations.

  14. Petroleum Processing Wastes.

    ERIC Educational Resources Information Center

    Baker, D. A.

    1978-01-01

    Presents a literature review of the petroleum processing wastes, covering publications of 1977. This review covers studies such as the use of activated carbon in petroleum and petrochemical waste treatment. A list of 15 references is also presented. (HM)

  15. Quantum Stochastic Processes

    SciTech Connect

    Spring, William Joseph

    2009-04-13

    We consider quantum analogues of n-parameter stochastic processes, associated integrals and martingale properties extending classical results obtained in [1, 2, 3], and quantum results in [4, 5, 6, 7, 8, 9, 10].

  16. [The irradiation process].

    PubMed

    Barillot, I; Chauvet, B; Hannoun Lévi, J M; Lisbona, A; Leroy, T; Mahé, M A

    2016-09-01

    The purpose of this article is to describe the regulatory framework of the radiotherapy practice in France, the external irradiation and brachytherapy process and the guidelines for patient follow-up.

  17. Processing composite materials

    NASA Technical Reports Server (NTRS)

    Baucom, R. M.

    1982-01-01

    The fabrication of several composite structural articles including DC-10 upper aft rudders, L-1011 vertical fins and composite biomedical appliances are discussed. Innovative composite processing methods are included.

  18. George: Gaussian Process regression

    NASA Astrophysics Data System (ADS)

    Foreman-Mackey, Daniel

    2015-11-01

    George is a fast and flexible library, implemented in C++ with Python bindings, for Gaussian Process regression useful for accounting for correlated noise in astronomical datasets, including those for transiting exoplanet discovery and characterization and stellar population modeling.

  19. Ultrasonic Processing of Materials

    NASA Astrophysics Data System (ADS)

    Han, Qingyou

    2015-08-01

    Irradiation of high-energy ultrasonic vibration in metals and alloys generates oscillating strain and stress fields in solids, and introduces nonlinear effects such as cavitation, acoustic streaming, and radiation pressure in molten materials. These nonlinear effects can be utilized to assist conventional material processing processes. This article describes recent research at Oak Ridge National Labs and Purdue University on using high-intensity ultrasonic vibrations for degassing molten aluminum, processing particulate-reinforced metal matrix composites, refining metals and alloys during solidification process and welding, and producing bulk nanostructures in solid metals and alloys. Research results suggest that high-intensity ultrasonic vibration is capable of degassing and dispersing small particles in molten alloys, reducing grain size during alloy solidification, and inducing nanostructures in solid metals.

  20. Cooperative processing data bases

    NASA Technical Reports Server (NTRS)

    Hasta, Juzar

    1991-01-01

    Cooperative processing for the 1990's using client-server technology is addressed. The main theme is concepts of downsizing from mainframes and minicomputers to workstations on a local area network (LAN). This document is presented in view graph form.

  1. Phenol removal pretreatment process

    DOEpatents

    Hames, Bonnie R.

    2004-04-13

    A process for removing phenols from an aqueous solution is provided, which comprises the steps of contacting a mixture comprising the solution and a metal oxide, forming a phenol metal oxide complex, and removing the complex from the mixture.

  2. Plants: Novel Developmental Processes.

    ERIC Educational Resources Information Center

    Goldberg, Robert B.

    1988-01-01

    Describes the diversity of plants. Outlines novel developmental and complex genetic processes that are specific to plants. Identifies approaches that can be used to solve problems in plant biology. Cites the advantages of using higher plants for experimental systems. (RT)

  3. Associative list processing unit

    SciTech Connect

    Hemmert, Karl Scott; Underwood, Keith D

    2014-04-01

    An associative list processing unit and method comprising employing a plurality of prioritized cell blocks and permitting inserts to occur in a single clock cycle if all of the cell blocks are not full.

  4. Microwave processing of ceramics

    SciTech Connect

    Katz, J.D.

    1989-01-01

    This paper discusses the following topics on microwave processing of ceramics: Microwave-material interactions; anticipated advantage of microwave sintering; ceramic sintering; and ceramic joining. 24 refs., 4 figs. (LSP)

  5. Space processing economics

    NASA Technical Reports Server (NTRS)

    Bredt, J. H.

    1974-01-01

    Two types of space processing operations may be considered economically justified; they are manufacturing operations that make profits and experiment operations that provide needed applied research results at lower costs than those of alternative methods. Some examples from the Skylab experiments suggest that applied research should become cost effective soon after the space shuttle and Spacelab become operational. In space manufacturing, the total cost of space operations required to process materials must be repaid by the value added to the materials by the processing. Accurate estimates of profitability are not yet possible because shuttle operational costs are not firmly established and the markets for future products are difficult to estimate. However, approximate calculations show that semiconductor products and biological preparations may be processed on a scale consistent with market requirements and at costs that are at least compatible with profitability using the Shuttle/Spacelab system.

  6. Superfund Site Assessment Process

    EPA Pesticide Factsheets

    Learn about the site assessment process used by the federal Superfund program to evaluate releases of hazardous substances that may pose a threat to human health or the environment and select an appropriate program for sites needing cleanup.

  7. Advances in Process Control.

    ERIC Educational Resources Information Center

    Morrison, David L.; And Others

    1982-01-01

    Advances in electronics and computer science have enabled industries (pulp/paper, iron/steel, petroleum/chemical) to attain better control of their processes with resulting increases in quality, productivity, profitability, and compliance with government regulations. (JN)

  8. CAPSULE REPORT: EVAPORATION PROCESS

    EPA Science Inventory

    Evaporation has been an established technology in the metal finishing industry for many years. In this process, wastewaters containing reusable materials, such as copper, nickel, or chromium compounds are heated, producing a water vapor that is continuously removed and condensed....

  9. Coal Liquefaction Processes.

    ERIC Educational Resources Information Center

    Yen, T. F.

    1979-01-01

    Described is a graduate level engineering course offered at the University of Southern California on coal liquefaction processes. Lecture topics and course requirements are discussed. A 64-item bibliography of papers used in place of a textbook is included. (BT)

  10. Direct coal liquefaction process

    DOEpatents

    Rindt, J.R.; Hetland, M.D.

    1993-10-26

    An improved multistep liquefaction process for organic carbonaceous mater which produces a virtually completely solvent-soluble carbonaceous liquid product. The solubilized product may be more amenable to further processing than liquid products produced by current methods. In the initial processing step, the finely divided organic carbonaceous material is treated with a hydrocarbonaceous pasting solvent containing from 10% and 100% by weight process-derived phenolic species at a temperature within the range of 300 C to 400 C for typically from 2 minutes to 120 minutes in the presence of a carbon monoxide reductant and an optional hydrogen sulfide reaction promoter in an amount ranging from 0 to 10% by weight of the moisture- and ash-free organic carbonaceous material fed to the system. As a result, hydrogen is generated via the water/gas shift reaction at a rate necessary to prevent condensation reactions. In a second step, the reaction product of the first step is hydrogenated.

  11. Coal Liquefaction Processes.

    ERIC Educational Resources Information Center

    Yen, T. F.

    1979-01-01

    Described is a graduate level engineering course offered at the University of Southern California on coal liquefaction processes. Lecture topics and course requirements are discussed. A 64-item bibliography of papers used in place of a textbook is included. (BT)

  12. Direct coal liquefaction process

    DOEpatents

    Rindt, John R.; Hetland, Melanie D.

    1993-01-01

    An improved multistep liquefaction process for organic carbonaceous mater which produces a virtually completely solvent-soluble carbonaceous liquid product. The solubilized product may be more amenable to further processing than liquid products produced by current methods. In the initial processing step, the finely divided organic carbonaceous material is treated with a hydrocarbonaceous pasting solvent containing from 10% and 100% by weight process-derived phenolic species at a temperature within the range of 300.degree. C. to 400.degree. C. for typically from 2 minutes to 120 minutes in the presence of a carbon monoxide reductant and an optional hydrogen sulfide reaction promoter in an amount ranging from 0 to 10% by weight of the moisture- and ash-free organic carbonaceous material fed to the system. As a result, hydrogen is generated via the water/gas shift reaction at a rate necessary to prevent condensation reactions. In a second step, the reaction product of the first step is hydrogenated.

  13. CAPSULE REPORT: EVAPORATION PROCESS

    EPA Science Inventory

    Evaporation has been an established technology in the metal finishing industry for many years. In this process, wastewaters containing reusable materials, such as copper, nickel, or chromium compounds are heated, producing a water vapor that is continuously removed and condensed....

  14. Petroleum Processing Wastes.

    ERIC Educational Resources Information Center

    Baker, D. A.

    1978-01-01

    Presents a literature review of the petroleum processing wastes, covering publications of 1977. This review covers studies such as the use of activated carbon in petroleum and petrochemical waste treatment. A list of 15 references is also presented. (HM)

  15. Shaping process makes fuels

    SciTech Connect

    Tabak, S.A.; Krambeck, F.J.

    1985-09-01

    The Mobil Olefin to Gasoline and Distillate (MOGD) process is described in which light olefinic compunds can be converted to high quality gasoline and distillate. This process, now ready for commercialization is based on a unique synthetic zeolite catalyst, the shape of which selectively oligomerizes light olefins to higher molecular weight iso-olefins. The highly flexible process can be designed to produce distillate/gasoline ratios of 0/100 to 90/10 for a commercial plant, depending on market requirements. MOGD is applicable to a wide range of feed streams ranging from ethylene to 400 degrees F end point olefinic naphtha. The process has been tested using commercially produced catalyst in refinery-scale equipment.

  16. Process for preparing hydrocarbons

    SciTech Connect

    Breuker, J.H.; De H.H.; Kwant, P.B.

    1980-01-15

    A process for preparing light distillate fractions and medicinal oil from heavy hydrocarbon oils comprises two-stage hydrocracking, fractionation distillation and catalytic hydrotreatment of at least part of the fractionation residue.

  17. Lesson 6: Submission Process

    EPA Pesticide Factsheets

    Checklist items 8 through 12 are grouped under the Submission Process, and represent the CROMERR requirements that must be satisfied as the report or document is transferred to the system during a formal submission.

  18. Plants: Novel Developmental Processes.

    ERIC Educational Resources Information Center

    Goldberg, Robert B.

    1988-01-01

    Describes the diversity of plants. Outlines novel developmental and complex genetic processes that are specific to plants. Identifies approaches that can be used to solve problems in plant biology. Cites the advantages of using higher plants for experimental systems. (RT)

  19. Advances in Process Control.

    ERIC Educational Resources Information Center

    Morrison, David L.; And Others

    1982-01-01

    Advances in electronics and computer science have enabled industries (pulp/paper, iron/steel, petroleum/chemical) to attain better control of their processes with resulting increases in quality, productivity, profitability, and compliance with government regulations. (JN)

  20. Image Processing Software

    NASA Technical Reports Server (NTRS)

    1990-01-01

    The Ames digital image velocimetry technology has been incorporated in a commercially available image processing software package that allows motion measurement of images on a PC alone. The software, manufactured by Werner Frei Associates, is IMAGELAB FFT. IMAGELAB FFT is a general purpose image processing system with a variety of other applications, among them image enhancement of fingerprints and use by banks and law enforcement agencies for analysis of videos run during robberies.

  1. Near Shore Wave Processes

    DTIC Science & Technology

    2016-06-07

    given the offshore wave conditions . OBJECTIVES We hypothesize that the wave-induced kinematic, sediment and morphologic processes are nonlinearly... WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Naval Postgraduate School,Department of Oceanography,Monterey,CA,93943 8...basis of our process modeling and analysis work . In addition, the comprehensive Delft3D morphology model was acquired from the Dutch and is being assessed

  2. Materials Processing in Space

    NASA Technical Reports Server (NTRS)

    Naumann, R. J.

    1982-01-01

    A report describes investigations of materials processing in low-gravity environment. Ultimately, research could lead to new commercially-applicable materials and processes and to an understanding of constraints imposed by gravity. NASA-supported work is carried out in 46 academic, industrial, and Government laboratories, and covers a number of areas. An overview is given of objective and current state of development for over 100 tasks.

  3. Advanced Polymer Processing Facility

    SciTech Connect

    Muenchausen, Ross E.

    2012-07-25

    Some conclusions of this presentation are: (1) Radiation-assisted nanotechnology applications will continue to grow; (2) The APPF will provide a unique focus for radiolytic processing of nanomaterials in support of DOE-DP, other DOE and advanced manufacturing initiatives; (3) {gamma}, X-ray, e-beam and ion beam processing will increasingly be applied for 'green' manufacturing of nanomaterials and nanocomposites; and (4) Biomedical science and engineering may ultimately be the biggest application area for radiation-assisted nanotechnology development.

  4. Bank Record Processing

    NASA Technical Reports Server (NTRS)

    1982-01-01

    Barnett Banks of Florida, Inc. operates 150 banking offices in 80 Florida cities. Banking offices have computerized systems for processing deposits or withdrawals in checking/savings accounts, and for handling commercial and installment loan transactions. In developing a network engineering design for the terminals used in record processing, an affiliate, Barnett Computing Company, used COSMIC's STATCOM program. This program provided a reliable network design tool and avoided the cost of developing new software.

  5. Research in Stochastic Processes.

    DTIC Science & Technology

    1985-09-01

    appear. G. Kallianpur, Finitely additive approach to nonlinear filtering, Proc. Bernoulli Soc. Conf. on Stochastic Processes, T. Hida , ed., Springer, to...Nov. 85, in Proc. Bernoulli Soc. Conf. on Stochastic Processes, T. Hida , ed., Springer, to appear. i. Preparation T. Hsing, Extreme value theory for...1507 Carroll, R.J., Spiegelman, C.H., Lan, K.K.G., Bailey , K.T. and Abbott, R.D., Errors in-variables for binary regression models, Aug.82. 1508

  6. Solution Processing - Rodlike Polymers

    DTIC Science & Technology

    1979-08-01

    side it necessary and identify by block number) Para-ordered Polymers High Modulus Fibers and Films Polybenzobisoxazoles Polybenzobisthiazoles 20...considerations important in solution processing are considered, with special emphasis on the dry-jet wet spinning process used to form fibers . Pertinent...Company, Summit, N.J. iii TABLE OF CONTENTS 1. INTRODUCTION ................ .......................... .. 1 2. REMARKS ON DRY-JET WET SPUN FIBER

  7. Coal liquefaction process

    DOEpatents

    Karr, Jr., Clarence

    1977-04-19

    An improved coal liquefaction process is provided which enables conversion of a coal-oil slurry to a synthetic crude refinable to produce larger yields of gasoline and diesel oil. The process is characterized by a two-step operation applied to the slurry prior to catalytic desulfurization and hydrogenation in which the slurry undergoes partial hydrogenation to crack and hydrogenate asphaltenes and the partially hydrogenated slurry is filtered to remove minerals prior to subsequent catalytic hydrogenation.

  8. Business Development Process

    DTIC Science & Technology

    2001-10-31

    entity’s real estate situation and condition for use by 17 customers including (but not limited to) the business entity. 18 Information is processed to...the score to provide a well- 3 rounded picture of a particular real estate situation. 4 Stratmann discloses a method for assisting an individual in...identify a potential 9 flaw in the opportunity analysis . These criteria include whether 10 the process is dealing with a real customer, if it is

  9. Retrofitting heavy oil processes

    SciTech Connect

    Hamilton, G.L.; Fitzgerald, M.; D'Amico, V.

    1986-01-01

    Refiners, faced with the need to process the bottom end of the heavy high sulfur crude oil barrel in today's uncertain economic environment, are reluctant to commit large amounts of money to expensive upgrading processes. In order to conserve scarce capital while improving operating margins, additional valuable products can be produced by retrofits such as conversion of an idle crude unit to visbreaking, delayed coking or deasphalting service, or conversion of hydrodesulfurizers to mild hydrocracking.

  10. Qualitative Process Theory.

    DTIC Science & Technology

    1984-07-01

    AD-A148 987 QUALITATIVE PROCESS THEORY(U) MASSACHUSETTS INST OF 1/2 TEEH CAMBRIDGE ARTIFICIAL INTELLIGENCE LAB K D FORBUS JUL 84 RI-TR-789 N88814-80...NATIONAL BUREAU Of STAN ARDS IJ% A 4 I .7 Technical Report 789 Q[-----Qualitative• Process M° Theory . Kenneth Dale Forbus MIT Artificial Intelligence ...PROGRAM ELEMENT. PROJECT. TASK Artificial Intelligence Laboratory AREA& WORK UNIT NUMBERS 545 Technology Square Cambridge, Massachusetts 02139 iI

  11. Hydrogen recovery process

    DOEpatents

    Baker, Richard W.; Lokhandwala, Kaaeid A.; He, Zhenjie; Pinnau, Ingo

    2000-01-01

    A treatment process for a hydrogen-containing off-gas stream from a refinery, petrochemical plant or the like. The process includes three separation steps: condensation, membrane separation and hydrocarbon fraction separation. The membrane separation step is characterized in that it is carried out under conditions at which the membrane exhibits a selectivity in favor of methane over hydrogen of at least about 2.5.

  12. Laser Processed Heat Exchangers

    NASA Technical Reports Server (NTRS)

    Hansen, Scott

    2017-01-01

    The Laser Processed Heat Exchanger project will investigate the use of laser processed surfaces to reduce mass and volume in liquid/liquid heat exchangers as well as the replacement of the harmful and problematic coatings of the Condensing Heat Exchangers (CHX). For this project, two scale unit test articles will be designed, manufactured, and tested. These two units are a high efficiency liquid/liquid HX and a high reliability CHX.

  13. Coal liquefaction process

    DOEpatents

    Skinner, Ronald W.; Tao, John C.; Znaimer, Samuel

    1985-01-01

    This invention relates to an improved process for the production of liquid carbonaceous fuels and solvents from carbonaceous solid fuels, especially coal. The claimed improved process includes the hydrocracking of the light SRC mixed with a suitable hydrocracker solvent. The recycle of the resulting hydrocracked product, after separation and distillation, is used to produce a solvent for the hydrocracking of the light solvent refined coal.

  14. Electrochemical Atomic Layer Processing

    DTIC Science & Technology

    1994-06-25

    where an atomic layer of an element is deposited , or removed, in a surface limited reaction. The potentials used are referred to as underpotentials in...the electrochemical literature. The atomic layer deposition process is referred to as underpotential deposition (UPD). 14. SUBJECT TERMS 15, NUMBER OF...reaction. The potentials used are referred to as underpotentials in the electrochemical literature. The atomic layer deposition process is referred to as

  15. Image Processing Software

    NASA Technical Reports Server (NTRS)

    1992-01-01

    To convert raw data into environmental products, the National Weather Service and other organizations use the Global 9000 image processing system marketed by Global Imaging, Inc. The company's GAE software package is an enhanced version of the TAE, developed by Goddard Space Flight Center to support remote sensing and image processing applications. The system can be operated in three modes and is combined with HP Apollo workstation hardware.

  16. Spherical nitroguanidine process

    DOEpatents

    Sanchez, John A.; Roemer, Edward L.; Stretz, Lawrence A.

    1990-01-01

    A process of preparing spherical high bulk density nitroguanidine by dissing low bulk density nitroguanidine in N-methyl pyrrolidone at elevated temperatures and then cooling the solution to lower temperatures as a liquid characterized as a nonsolvent for the nitroguanidine is provided. The process is enhanced by inclusion in the solution of from about 1 ppm up to about 250 ppm of a metal salt such as nickel nitrate, zinc nitrate or chromium nitrate, preferably from about 20 to about 50 ppm.

  17. Apple Image Processing Educator

    NASA Technical Reports Server (NTRS)

    Gunther, F. J.

    1981-01-01

    A software system design is proposed and demonstrated with pilot-project software. The system permits the Apple II microcomputer to be used for personalized computer-assisted instruction in the digital image processing of LANDSAT images. The programs provide data input, menu selection, graphic and hard-copy displays, and both general and detailed instructions. The pilot-project results are considered to be successful indicators of the capabilities and limits of microcomputers for digital image processing education.

  18. Dawn Spacecraft Processing

    NASA Image and Video Library

    2007-04-10

    In Astrotech's Payload Processing Facility, technicians help secure the Dawn spacecraft onto a moveable stand. Dawn will be moved into clean room C for unbagging and further processing. Dawn's mission is to explore two of the asteroid belt's most intriguing and dissimilar occupants: asteroid Vesta and the dwarf planet Ceres. The Dawn mission is managed by JPL, a division of the California Institute of Technology in Pasadena, for NASA's Science Mission Directorate in Washington, D.C.

  19. Unconventional olefin processes

    SciTech Connect

    Hu, Y.C.

    1983-05-01

    The conversion of syngas into olefins is based on the Fischer-Tropsch technology. The FT modified process for olefins includes: upgraded liquids for olefins and aromatics, and catcracking of methanol. Because of the number of catalysts for olefins, data is not yet possible. Economic projections suggest that methanol cracking for olefins will be feasible in 1990. Olefin demand will grow, and C/sub 1/ chemistry research will increase, so that some unconventional olefin processes can be commercialized by then.

  20. Textile composite processing science

    NASA Technical Reports Server (NTRS)

    Loos, Alfred C.; Hammond, Vincent H.; Kranbuehl, David E.; Hasko, Gregory H.

    1993-01-01

    A multi-dimensional model of the Resin Transfer Molding (RTM) process was developed for the prediction of the infiltration behavior of a resin into an anisotropic fiber preform. Frequency dependent electromagnetic sensing (FDEMS) was developed for in-situ monitoring of the RTM process. Flow visualization and mold filling experiments were conducted to verify sensor measurements and model predictions. Test results indicated good agreement between model predictions, sensor readings, and experimental data.