Viscosity Depressants for Coal Liquefaction

NASA Technical Reports Server (NTRS)

Kalfayan, S. H.

1983-01-01

Proposed process modification incorporates viscosity depressants to prevent coal from solidifying during liquefaction. Depressants reduce amount of heat needed to liquefy coal. Possible depressants are metallic soaps, such as stearate, and amides, such as stearamide and dimer acid amides.

Coal liquefaction process streams characterization and evaluation: Analysis of Black Thunder coal and liquefaction products from HRI Bench Unit Run CC-15

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pugmire, R.J.; Solum, M.S.

This study was designed to apply {sup 13}C-nuclear magnetic resonance (NMR) spectrometry to the analysis of direct coal liquefaction process-stream materials. {sup 13}C-NMR was shown to have a high potential for application to direct coal liquefaction-derived samples in Phase II of this program. In this Phase III project, {sup 13}C-NMR was applied to a set of samples derived from the HRI Inc. bench-scale liquefaction Run CC-15. The samples include the feed coal, net products and intermediate streams from three operating periods of the run. High-resolution {sup 13}C-NMR data were obtained for the liquid samples and solid-state CP/MAS {sup 13}C-NMR datamore » were obtained for the coal and filter-cake samples. The {sup 1}C-NMR technique is used to derive a set of twelve carbon structural parameters for each sample (CONSOL Table A). Average molecular structural descriptors can then be derived from these parameters (CONSOL Table B).« less

Coal liquefaction process

DOEpatents

Carr, Norman L.; Moon, William G.; Prudich, Michael E.

1983-01-01

A C.sub.5 -900.degree. F. (C.sub.5 -482.degree. C.) liquid yield greater than 50 weight percent MAF feed coal is obtained in a coal liquefaction process wherein a selected combination of higher hydrogen partial pressure, longer slurry residence time and increased recycle ash content of the feed slurry are controlled within defined ranges.

Fired heater for coal liquefaction process

DOEpatents

Ying, David H. S.; McDermott, Wayne T.; Givens, Edwin N.

1985-01-01

A fired heater for a coal liquefaction process is operated under conditions to maximize the slurry slug frequency and thereby improve the heat transfer efficiency. The operating conditions controlled are (1) the pipe diameter and pipe arrangement, (2) the minimum coal/solvent slurry velocity, (3) the maximum gas superficial velocity, and (4) the range of the volumetric flow velocity ratio of gas to coal/solvent slurry.

Catalysts and process developments for two-stage liquefaction. Third quarterly technical progress report No. 44, April 1, 1991--June 30, 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cronauer, D.C.; Swanson, A.J.; Sajkowski, D.J.

Research under way in this project centers upon developing and evaluating catalysts and process improvements for coal liquefaction in the two-stage close-coupled catalytic process. As documented in the previous quarterly report (Task 3.1), there was little advantage for presoaking Black Thunder coal or Martin Lake lignite in a hydrogen-donor solvent, such as tetralin, at temperatures up to 600{degrees}F prior to liquefaction at higher temperatures. The amount of decarboxylation that occurred during the presoaking of Black Thunder coal or Martin Lake lignite in tetralin in the temperature range of 400 to 600{degrees}F was also relatively small. Further experimentation was undertaken inmore » a continuous flow unit with Black Thunder coal, where the primary goal was to determine the extent of decarboxylation and changes in the structure of the unconverted coal samples. The preliminary results indicated little conversion of the feed coal to THF solubles at 600{degrees}F, although the conversion did increase with increasing temperature up to 24% at 700{degrees}F. The level of decarboxylation was also low at the above reaction temperatures. Thus, presoaking in a coal-derived solvent or even tetralin does not seem to be an effective means to achieve decarboxylation. A suitable sample of Illinois No. 6 coal was received and tested for liquefaction. The batch liquefaction showed that this sample had good reactivity. The continuous liquefaction test was done in a two-stage unit with AMOCAT{trademark}-1C catalyst in both reactors. A significant amount of resid was produced throughout this three-week run. As the catalyst aged, the distillate production decreased and its product quality got worse. The feedstock liquefaction studies for the three feedstocks (Black Thunder subbituminous coal, Martin Lake lignite, and Illinois No. 6 coal) have been completed, and their results will be compared in a subsequent quarterly report.« less

Catalyst system and process for benzyl ether fragmentation and coal liquefaction

DOEpatents

Zoeller, Joseph Robert

1998-04-28

Dibenzyl ether can be readily cleaved to form primarily benzaldehyde and toluene as products, along with minor amounts of bibenzyl and benzyl benzoate, in the presence of a catalyst system comprising a Group 6 metal, preferably molybdenum, a salt, and an organic halide. Although useful synthetically for the cleavage of benzyl ethers, this cleavage also represents a key model reaction for the liquefaction of coal; thus this catalyst system and process should be useful in coal liquefaction with the advantage of operating at significantly lower temperatures and pressures.

Fired heater for coal liquefaction process

DOEpatents

Ying, David H. S.

1984-01-01

A fired heater for a coal liquefaction process is constructed with a heat transfer tube having U-bends at regular intervals along the length thereof to increase the slug frequency of the multi-phase mixture flowing therethrough to thereby improve the heat transfer efficiency.

Catalysts and process development for two-stage liquefaction. First quarterly report, January 1, 1992--March 31, 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cronauer, D.C.; Swanson, A.J.; Sajkowski, D.J.

Research under way in this project centers upon developing and evaluating catalysts and process improvements for coal liquefaction in the two-stage, close-coupled catalytic process. The project is being carried out under contract to the United States Department of Energy. As discussed in the previous quarterly report, promising results were obtained by liquefying Illinois No. 6 bituminous and Black Thunder subbituminous coals using oil-soluble catalysts Molyvan L and molybdenum octoate. In this quarter, the liquefaction of Black Thunder coal was continued. Runs were made in catalytic/thermal (C/T) mode with supported AMOCAT{trademark} 1C (NiMo) and AMOCAT{trademark} 1B (Mo) catalysts. Although the initialmore » performance in these runs was good (90% conversion with no resid production), both catalysts deactivated rapidly. Spent catalysts showed severe coke deposition as well as formation of a calcium-rich shell on the catalyst surface. Overall, C/T liquefaction is not a good process option for Black Thunder coal.« less

Coal liquefaction process streams characterization and evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, G.; Davis, A.; Burke, F.P.

1991-12-01

This study demonstrated the use of the gold tube carbonization technique and reflectance microscopy analysis for the examination of process-derived materials from direct coal liquefaction. The carbonization technique, which was applied to coal liquefaction distillation resids, yields information on the amounts of gas plus distillate, pyridine-soluble resid, and pyridine-insoluble material formed when a coal liquid sample is heated to 450{degree}C for one hour at 5000 psi in an inert atmosphere. The pyridine-insolubles then are examined by reflectance microscopy to determine the type, amount, and optical texture of isotropic and anisotropic carbon formed upon carbonization. Further development of these analytical methodsmore » as process development tools may be justified on the basis of these results.« less

Coal liquefaction process

DOEpatents

Karr, Jr., Clarence

1977-04-19

An improved coal liquefaction process is provided which enables conversion of a coal-oil slurry to a synthetic crude refinable to produce larger yields of gasoline and diesel oil. The process is characterized by a two-step operation applied to the slurry prior to catalytic desulfurization and hydrogenation in which the slurry undergoes partial hydrogenation to crack and hydrogenate asphaltenes and the partially hydrogenated slurry is filtered to remove minerals prior to subsequent catalytic hydrogenation.

Catalytic multi-stage liquefaction of coal at HTI: Bench-scale studies in coal/waste plastics coprocessing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pradhan, V.R.; Lee, L.K.; Stalzer, R.H.

1995-12-31

The development of Catalytic Multi-Stage Liquefaction (CMSL) at HTI has focused on both bituminous and sub-bituminous coals using laboratory, bench and PDU scale operations. The crude oil equivalent cost of liquid fuels from coal has been curtailed to about $30 per barrel, thus achieving over 30% reduction in the price that was evaluated for the liquefaction technologies demonstrated in the late seventies and early eighties. Contrary to the common belief, the new generation of catalytic multistage coal liquefaction process is environmentally very benign and can produce clean, premium distillates with a very low (<10ppm) heteroatoms content. The HTI Staff hasmore » been involved over the years in process development and has made significant improvements in the CMSL processing of coals. A 24 month program (extended to September 30, 1995) to study novel concepts, using a continuous bench scale Catalytic Multi-Stage unit (30kg coal/day), has been initiated since December, 1992. This program consists of ten bench-scale operations supported by Laboratory Studies, Modelling, Process Simulation and Economic Assessments. The Catalytic Multi-Stage Liquefaction is a continuation of the second generation yields using a low/high temperature approach. This paper covers work performed between October 1994- August 1995, especially results obtained from the microautoclave support activities and the bench-scale operations for runs CMSL-08 and CMSL-09, during which, coal and the plastic components for municipal solid wastes (MSW) such as high density polyethylene (HDPE)m, polypropylene (PP), polystyrene (PS), and polythylene terphthlate (PET) were coprocessed.« less

Literature survey of properties of synfuels derived from coal

NASA Technical Reports Server (NTRS)

Flores, F.

1982-01-01

A literature survey of the properties of synfuels for ground-based turbine applications is presented. The four major concepts for converting coal into liquid fuels (solvent extraction, catalytic liquefaction, pyrolysis, and indirect liquefaction), and the most important concepts for coal gasification (fixed bed, fluidized bed, entrained flow, and underground gasification) are described. Upgrading processes for coal derived liquid fuels are also described. Data presented for liquid fuels derived from various processes, including H-coal, synthoil, solvent refined coal, COED, donor solvent, zinc chloride hydrocracking, co-steam, and flash pyrolysis. Typical composition, and property data is also presented for low and medium-BTU gases derived from the various coal gasification processes.

Proceedings: Fourteenth annual EPRI conference on fuel science

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-05-01

EPRI's Fourteenth Annual Contractors' Conference on Fuel Science was held on May 18--19, 1989 in Palo Alto, CA. The conference featured results of work on coal science, coal liquefaction, methanol production, and coal oil coprocessing and coal upgrading. The following topics were discussed: recent development in coal liquefaction at the Wilsonville Clean Coal Research Center; British coal's liquid solvent extraction (LSE) process; feedstock reactivity in coal/oil co-processing; utility applications for coal-oil coprocessed fuels; effect of coal rank and quality on two-stage liquefaction; organic sulfur compounds in coals; the perchloroethylene refining process of high-sulfur coals; extraction of sulfur coals; extraction ofmore » sulfur from coal; agglomeration of bituminous and subbituminous coals; solubilization of coals by cell-free extracts derived from polyporus versicolor; remediation technologies and services; preliminary results from proof-of-concept testing of heavy liquid cyclone cleaning technology; clean-up of soil contaminated with tarry/oily organics; midwest ore processing company's coal benefication technology: recent prep plant, scale and laboratory activities; combustion characterization of coal-oil agglomerate fuels; status report on the liquid phase methanol project; biomimetic catalysis; hydroxylation of C{sub 2} {minus} C{sub 3} and cycloc{sub 6} hydrocarbons with Fe cluster catalysts as models for methane monooxygenase enzyme; methanol production scenarios; and modeling studies of the BNL low temperature methanol catalyst. Individual projects are processed separately for the data bases.« less

Royal Society, Discussion on New Coal Chemistry, London, England, May 21, 22, 1980, Proceedings

NASA Astrophysics Data System (ADS)

1981-03-01

A discussion of new coal chemistry is presented. The chemical and physical structure of coal is examined in the first section, including structural studies of coal extracts, metal and metal complexes in coal and coal microporosity. The second section presents new advances in applied coal technology. The development of liquid fuels and chemicals from coal is given especial emphasis, with papers on the Sasol Synthol process, the Shell-Koppers gasification process, liquefaction and gasification in Germany, the Solvent Refined Coal process, the Exxon Donor Solvent liquefaction process and the Mobil Methanol-to-Gasoline process. Finally, some developments that will be part of the future of coal chemistry in the year 2000 are examined in the third section, including coal-based chemical complexes and the use of coal as an alternative source to oil for chemical feedstocks.

Liquefaction of black thunder coal with counterflow reactor technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parker, R.J.; Simpson, P.L.

There is currently a resurgence of interest in the use of carbon monoxide and water to promote the solubilization of low rank coals in liquefaction processes. The mechanism for the water shift gas reaction (WGSR) is well documented and proceeds via a formate ion intermediate at temperatures up to about 400{degrees}C. Coal solubilization is enhanced by CO/H{sub 2}O and by the solvent effect of the supercritical water. The WGSR is catalyzed by bases (alkali metal carbonates, hydroxides, acetates, aluminates). Many inorganic salts which promote catalytic hydrogenation are rendered inactive in CO/H{sub 2}O, although there is positive evidence for the benefitmore » of using pyrite for both the WGSR and as a hydrogenation catalyst. The temperatures at which coal solubilization occurs are insufficient to promote extensive cracking or upgrading of the solubilized coal. Therefore, a two step process might achieve these two reactions sequentially. Alberta Research Council (ARC) has developed a two-stage process for the coprocessing of low rank coals and petroleum resids/bitumens. This process was further advanced by utilizing the counterflow reactor (CFR) concept pioneered by Canadian Energy Developments (CED) and ARC. The technology is currently being applied to coal liquefaction. The two-stage process employs CO/H{sub 2}O at relatively mid temperature and pressure to solubilize the coal, followed by a more severe hydrocracking step. This paper describes the results of an autoclave study conducted to support a bench unit program on the direct liquefaction of coals.« less

Case studies on direct liquefaction of low rank Wyoming coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adler, P.; Kramer, S.J.; Poddar, S.K.

Previous Studies have developed process designs, costs, and economics for the direct liquefaction of Illinois No. 6 and Wyoming Black Thunder coals at mine-mouth plants. This investigation concerns two case studies related to the liquefaction of Wyoming Black Thunder coal. The first study showed that reducing the coal liquefaction reactor design pressure from 3300 to 1000 psig could reduce the crude oil equivalent price by 2.1 $/bbl provided equivalent performing catalysts can be developed. The second one showed that incentives may exist for locating a facility that liquifies Wyoming coal on the Gulf Coast because of lower construction costs andmore » higher labor productivity. These incentives are dependent upon the relative values of the cost of shipping the coal to the Gulf Coast and the increased product revenues that may be obtained by distributing the liquid products among several nearby refineries.« less

Coal liquefaction process streams characterization and evaluation. Gold tube carbonization and reflectance microscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, G.; Davis, A.; Burke, F.P.

1991-12-01

This study demonstrated the use of the gold tube carbonization technique and reflectance microscopy analysis for the examination of process-derived materials from direct coal liquefaction. The carbonization technique, which was applied to coal liquefaction distillation resids, yields information on the amounts of gas plus distillate, pyridine-soluble resid, and pyridine-insoluble material formed when a coal liquid sample is heated to 450{degree}C for one hour at 5000 psi in an inert atmosphere. The pyridine-insolubles then are examined by reflectance microscopy to determine the type, amount, and optical texture of isotropic and anisotropic carbon formed upon carbonization. Further development of these analytical methodsmore » as process development tools may be justified on the basis of these results.« less

The direct liquefaction proof of concept program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Comolli, A.G.; Lee, L.K.; Pradhan, V.R.

1995-12-31

The goal of the Proof of Concept (POC) Program is to develop Direct Coal Liquefaction and associated transitional technologies towards commercial readiness for economically producing premium liquid fuels from coal in an environmentally acceptable manner. The program focuses on developing the two-stage liquefaction (TSL) process by utilizing geographically strategic feedstocks, commercially feasible catalysts, new prototype equipment, and testing co-processing or alternate feedstocks and improved process configurations. Other high priority objectives include dispersed catalyst studies, demonstrating low rank coal liquefaction without solids deposition, improving distillate yields on a unit reactor volume basis, demonstrating ebullated bed operations while obtaining scale-up data, demonstratingmore » optimum catalyst consumption using new concepts (e.g. regeneration, cascading), producing premium products through on-line hydrotreating, demonstrating improved hydrogen utilization for low rank coals using novel heteroatom removal methods, defining and demonstrating two-stage product properties for upgrading; demonstrating efficient and economic solid separation methods, examining the merits of integrated coal cleaning, demonstrating co-processing, studying interactions between the preheater and first and second-stage reactors, improving process operability by testing and incorporating advanced equipment and instrumentation, and demonstrating operation with alternate coal feedstocks. During the past two years major PDU Proof of Concept runs were completed. POC-1 with Illinois No. 6 coal and POC-2 with Black Thunder sub-bituminous coal. Results from these operations are continuing under review and the products are being further refined and upgraded. This paper will update the results from these operations and discuss future plans for the POC program.« less

Coal Liquefaction desulfurization process

DOEpatents

Givens, Edwin N.

1983-01-01

In a solvent refined coal liquefaction process, more effective desulfurization of the high boiling point components is effected by first stripping the solvent-coal reacted slurry of lower boiling point components, particularly including hydrogen sulfide and low molecular weight sulfur compounds, and then reacting the slurry with a solid sulfur getter material, such as iron. The sulfur getter compound, with reacted sulfur included, is then removed with other solids in the slurry.

Method for controlling boiling point distribution of coal liquefaction oil product

DOEpatents

Anderson, R.P.; Schmalzer, D.K.; Wright, C.H.

1982-12-21

The relative ratio of heavy distillate to light distillate produced in a coal liquefaction process is continuously controlled by automatically and continuously controlling the ratio of heavy distillate to light distillate in a liquid solvent used to form the feed slurry to the coal liquefaction zone, and varying the weight ratio of heavy distillate to light distillate in the liquid solvent inversely with respect to the desired weight ratio of heavy distillate to light distillate in the distillate fuel oil product. The concentration of light distillate and heavy distillate in the liquid solvent is controlled by recycling predetermined amounts of light distillate and heavy distillate for admixture with feed coal to the process in accordance with the foregoing relationships. 3 figs.

Method for controlling boiling point distribution of coal liquefaction oil product

DOEpatents

Anderson, Raymond P.; Schmalzer, David K.; Wright, Charles H.

1982-12-21

The relative ratio of heavy distillate to light distillate produced in a coal liquefaction process is continuously controlled by automatically and continuously controlling the ratio of heavy distillate to light distillate in a liquid solvent used to form the feed slurry to the coal liquefaction zone, and varying the weight ratio of heavy distillate to light distillate in the liquid solvent inversely with respect to the desired weight ratio of heavy distillate to light distillate in the distillate fuel oil product. The concentration of light distillate and heavy distillate in the liquid solvent is controlled by recycling predetermined amounts of light distillate and heavy distillate for admixture with feed coal to the process in accordance with the foregoing relationships.

Two-stage coal liquefaction process

DOEpatents

Skinner, Ronald W.; Tao, John C.; Znaimer, Samuel

1985-01-01

An improved SRC-I two-stage coal liquefaction process which improves the product slate is provided. Substantially all of the net yield of 650.degree.-850.degree. F. heavy distillate from the LC-Finer is combined with the SRC process solvent, substantially all of the net 400.degree.-650.degree. F. middle distillate from the SRC section is combined with the hydrocracker solvent in the LC-Finer, and the initial boiling point of the SRC process solvent is increased sufficiently high to produce a net yield of 650.degree.-850.degree. F. heavy distillate of zero for the two-stage liquefaction process.

Coal liquefaction with subsequent bottoms pyrolysis

DOEpatents

Walchuk, George P.

1978-01-01

In a coal liquefaction process wherein heavy bottoms produced in a liquefaction zone are upgraded by coking or a similar pyrolysis step, pyrolysis liquids boiling in excess of about 1000.degree. F. are further reacted with molecular hydrogen in a reaction zone external of the liquefaction zone, the resulting effluent is fractionated to produce one or more distillate fractions and a bottoms fraction, a portion of this bottoms fraction is recycled to the reaction zone, and the remaining portion of the bottoms fraction is recycled to the pyrolysis step.

Thermodynamic Analysis on of Skid-Mounted Coal-bed Methane Liquefaction Device using Cryogenic Turbo-Expander

NASA Astrophysics Data System (ADS)

Chen, Shuangtao; Niu, Lu; Zeng, Qiang; Li, Xiaojiang; Lou, Fang; Chen, Liang; Hou, Yu

2017-12-01

Coal-bed methane (CBM) reserves are rich in Sinkiang of China, and liquefaction is a critical step for the CBM exploration and utilization. Different from other CBM gas fields in China, CBM distribution in Sinkiang is widespread but scattered, and the pressure, flow-rate and nitrogen content of CBM feed vary significantly. The skid-mounted liquefaction device is suggested as an efficient and economical way to recover methane. Turbo-expander is one of the most important parts which generates the cooling capacity for the cryogenic liquefaction system. Using turbo-expander, more cooling capacity and higher liquefied fraction can be achieved. In this study, skid-mounted CBM liquefaction processes based on Claude cycle are established. Cryogenic turbo-expander with high expansion ratio is employed to improve the efficiency of CBM liquefaction process. The unit power consumption per liquefaction mole flow-rate for CBM feed gas is used as the object function for process optimization, compressor discharge pressure, flow ratio of feed gas to turbo-expander and nitrogen friction are analyzed, and optimum operation range of the liquefaction processes are obtained.

Method for coal liquefaction

DOEpatents

Wiser, Wendell H.; Oblad, Alex G.; Shabtai, Joseph S.

1994-01-01

A process is disclosed for coal liquefaction in which minute particles of coal in intimate contact with a hydrogenation catalyst and hydrogen arc reacted for a very short time at a temperature in excess of 400.degree. C. at a pressure of at least 1500 psi to yield over 50% liquids with a liquid to gaseous hydrocarbon ratio in excess of 8:1.

Direct liquefaction proof-of-concept program. Finaltopical report, Bench Run 4 (227-95)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Comolli, A.G.; Pradhan, V.R.; Lee, T.L.K.

This report presents the results of bench-scale work, Bench Run PB-04, conducted under the DOE Proof of Concept-Bench Option Program in direct coal liquefaction at Hydrocarbon Technologies, Inc. in Lawrenceville, New Jersey. The Bench Run PB-04 was the fifth of the nine runs planned in the POC Bench Option Contract between the U.S. DOE and Hydrocarbon Technologies, Inc. Bench Run PB-04 had multiple goals. These included the evaluation of the effects of dispersed slurry catalyst system on the performance of direct liquefaction of a subbituminous Wyoming Black Thunder mine coal under extinction recycle (454{degrees}C+ recycle) condition; another goal was tomore » investigate the effects of the combined processing of automobile shredder residue (auto-fluff) with coal and other organic waste materials. PB-04 employed a two-stage, back-mixed, slurry reactor system with an interstage V/L separator and an in-line fixed-bed hydrotreater. The HTI`s newly modified P/Fe catalyst was very effective for direct liquefaction and coprocessing of Black Thunder mine subbituminous coal with Hondo resid and auto-fluff; during `coal-only` liquefaction mode, over 93% maf coal conversion was obtained with about 90% residuum conversion and as high as 67% light distillate (C{sub 4}-975 F) yield, while during `coprocessing` mode of operation, distillate yields varied between 58 and 69%; the residuum conversions varied between 74 and 89% maf. Overall, it is concluded, based upon the yield data available from PB-04, that auto-effective as MSW plastics in improving coal hydroconversion process performance. Auto-fluff did not increase light distillate yields nor decrease light gas make and chemical hydrogen consumption in coal liquefaction, as was observed to occur with MSW plastics.« less

Coal liquefaction process solvent characterization and evaluation: Progress report, 1 April--30 June 1986

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winschel, R. A.; Robbins, G. A.; Burke, F. P.

1986-11-01

Conoco Coal Research Division is characterizing samples of direct coal liquefaction process oils based on a variety of analytical techniques to provide a detailed description of the chemical composition of the oils to more fully understand the interrelationship of process oil composition and process operations, to aid in plant operation, and to lead to process improvements. The approach taken is to obtain analyses of a large number of well-defined process oils taken during periods of known operating conditions and known process performance. A set of thirty-one process oils from the Hydrocarbon Research, Inc. (HRI) Catalytic Two-Stage Liquefaction (CTSL) bench unitmore » was analyzed to provide information on process performance. The Fourier-Transform infrared (FTIR) spectroscopic method for the determination of phenolics in cola liquids was further verified. A set of four tetahydrofuran-soluble products from Purdue Research Foundation's reactions of coal/potassium/crown ether, analyzed by GC/MS and FTIR, were found to consist primarily of paraffins (excluding contaminants). Characterization data (elemental analyses, /sup 1/H-NMR and phenolic concentrations) were obtained on a set of twenty-seven two-stage liquefaction oils. Two activities were begun but not completed. First, analyses were started on oils from Wilsonville Run 250 (close- coupled ITSL). Also, a carbon isotopic method is being examined for utility in determining the relative proportion of coal and petroleum products in coprocessing oils.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cada, G.F.

H-coal is a process for the direct liquefaction of coal to produce synthetic fuels. Its development has progressed from bench-scale testing through operation of a 2.7 Mg/d (3 ton/d) Process Development Unit. A large-scale H-Coal pilot plant is presently operating at Catlettsburg, Kentucky, and there are plans for the construction of a commercial H-Coal liquefaction facility by the end of the decade. Two of the environmental concerns of the developing direct coal liquefaction industry are accidental spills of synthetic oils and treatment/storage of solid wastes. As a means of obtaining preliminary information on the severity of these potential impacts wellmore » in advance of commercialization, samples of product oils and solid wastes were obtained from the H-Coal Process Development Unit (PDU). These samples were subjected to a battery of rapid screening tests, including chemical characterization and bioassays with a variety of aquatic and terrestrial organisms. Water-soluble fraction (WSFs) of H-Coal PDU oils had considerably higher concentrations of phenols and anilines and were commonly one to two orders of magnitude more toxic to aquatic organisms than WSFs of analogous petroleum crude oil. Whole H-Coal PDU oils were also more toxic to the cricket than petroleum-based oils, and some H-Coal samples showed evidence of teratogenicity. Leachates from H-Coal PDU solid wastes, on the other hand, had relatively low concentrations of selected elements and had essentially no acute toxicity to a variety of aquatic and terrestrial species. These studies indicate that environmental effects of product oil spills from a commercial H-Coal liquefaction plant are likely to be more severe than those of conventional petroleum spills. Product upgrading or special transportation and storage techniques may be needed to ensure environmentally sound commercialization of the H-Coal process.« less

Catalysts and process developments for two-stage liquefaction. Fourth quarterly technical progress report, July 1, 1991--September 30, 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cronauer, D.C.; Swanson, A.J.; Sajkowski, D.J.

Research under way in this project centers upon developing and evaluating catalysts and process improvements for coal liquefaction in the two-stage close-coupled catalytic process. As documented in the previous quarterly report there was little advantage for presoaking Black Thunder coal or Martin Lake lignite in a hydrogen-donor solvent, such as tetralin, at temperatures up to 600{degrees}F prior to liquefaction at higher temperatures. The amount of decarboxylation that occurred during the presoaking of Black Thunder coal or Martin Lake lignite in tetralin in the temperature range of 400 to 600{degrees}F was also relatively small. As indicated by both CO{sub 2} releasemore » and the change in oxygen-containing coal functionality, the level of decarboxylation in coal-derived solvent seems to correlate with the depth of coal dissolution. The feedstock liquefaction studies for the three feedstocks (Black Thunder subbituminous coal, Martin Lake lignite, and Illinois No. 6 coal) have been completed, and their results were compared in this report. Both Black Thunder coal and Martin Lake lignite gave lighter products than Illinois No. 6 coal at similar process conditions. Severe catalyst deactivation in the first stage was also observed with the Martin Lake lignite run. The first stage catalyst testing program was started. After a successful reference run with Illinois No. 6 coal, a high temperature run with AMOCAT{trademark} 1C was completed. In addition, a run was made with Illinois No. 6 coal using an oil-soluble catalyst, Molyvan L, in the first stage and AMOCAT{trademark} 1C in the second stage, where preliminary run results look promising.« less

Cooperative research in coal liquefaction. Technical progress report, May 1, 1993--April 30, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huffman, G.P.

Accomplishments for the past year are presented for the following tasks: coliquefaction of coal with waste materials; catalysts for coal liquefaction to clean transportation fuels; fundamental research in coal liquefaction; and in situ analytical techniques for coal liquefaction and coal liquefaction catalysts some of the highlights are: very promising results have been obtained from the liquefaction of plastics, rubber tires, paper and other wastes, and the coliquefaction of wastes with coal; a number of water soluble coal liquefaction catalysts, iron, cobalt, nickel and molybdenum, have been comparatively tested; mossbauer spectroscopy, XAFS spectroscopy, TEM and XPS have been used to characterizemore » a variety of catalysts and other samples from numerous consortium and DOE liquefaction projects and in situ ESR measurements of the free radical density have been conducted at temperatures from 100 to 600{degrees}C and H{sub 2} pressures up to 600 psi.« less

Economics and siting of Fischer-Tropsch coal liquefaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henry, J.P. Jr.; Ferreira, J.P.; Benefiel, J.

The capital intensity and low conversion efficiency of Fischer-Tropsch synthesis makes it noncompetitive with conventional petroleum in the midterm (e.g., 5 to 10 years) under normal economic conditions. However, if crude oil prices rise to higher levels (e.g., $25 to $30/bbl), coal liquefaction processes may prove to be economical. It appears that several other processes under development may become economically attractive before Fischer-Tropsch, although Fischer-Tropsch is the only proven commercially feasible venture at present. The above statement is subject, however, to the successful demonstration and commercialization of these alternative processes. Fischer-Tropsch, as a commercially proven process, may be called uponmore » as a backup should petroleum shortages ensue, world oil prices continue to increase dramatically, and alternate coal liquefaction processes fail to fully develop.« less

Coal liquefaction process

DOEpatents

Maa, Peter S.

1978-01-01

A process for liquefying a particulate coal feed to produce useful petroleum-like liquid products which comprises contacting; in a series of two or more coal liquefaction zones, or stages, graded with respect to temperature, an admixture of a polar compound; or compounds, a hydrogen donor solvent and particulate coal, the total effluent being passed in each instance from a low temperature zone, or stage to the next succeeding higher temperature zone, or stage, of the series. The temperature within the initial zone, or stage, of the series is maintained about 70.degree. F and 750.degree. F and the temperature within the final zone, or stage, is maintained between about 750.degree. F and 950.degree. F. The residence time within the first zone, or stage, ranges, generally, from about 20 to about 150 minutes and residence time within each of the remaining zones, or stages, of the series ranges, generally, from about 10 minutes to about 70 minutes. Further steps of the process include: separating the product from the liquefaction zone into fractions inclusive of a liquid solvent fraction; hydrotreating said liquid solvent fraction in a hydrogenation zone; and recycling the hydrogenated liquid solvent mixture to said coal liquefaction zones.

Use of once-through treat gas to remove the heat of reaction in solvent hydrogenation processes

DOEpatents

Nizamoff, Alan J.

1980-01-01

In a coal liquefaction process wherein feed coal is contacted with molecular hydrogen and a hydrogen-donor solvent in a liquefaction zone to form coal liquids and vapors and coal liquids in the solvent boiling range are thereafter hydrogenated to produce recycle solvent and liquid products, the improvement which comprises separating the effluent from the liquefaction zone into a hot vapor stream and a liquid stream; cooling the entire hot vapor stream sufficiently to condense vaporized liquid hydrocarbons; separating condensed liquid hydrocarbons from the cooled vapor; fractionating the liquid stream to produce coal liquids in the solvent boiling range; dividing the cooled vapor into at least two streams; passing the cooling vapors from one of the streams, the coal liquids in the solvent boiling range, and makeup hydrogen to a solvent hydrogenation zone, catalytically hydrogenating the coal liquids in the solvent boiling range and quenching the hydrogenation zone with cooled vapors from the other cooled vapor stream.

Coal liquefaction process

DOEpatents

Wright, Charles H.

1986-01-01

A process for the liquefaction of coal wherein raw feed coal is dissolved in recycle solvent with a slurry containing recycle coal minerals in the presence of added hydrogen at elevated temperature and pressure. The highest boiling distillable dissolved liquid fraction is obtained from a vacuum distillation zone and is entirely recycled to extinction. Lower boiling distillable dissolved liquid is removed in vapor phase from the dissolver zone and passed without purification and essentially without reduction in pressure to a catalytic hydrogenation zone where it is converted to an essentially colorless liquid product boiling in the transportation fuel range.

Method for coal liquefaction

DOEpatents

Wiser, W.H.; Oblad, A.G.; Shabtai, J.S.

1994-05-03

A process is disclosed for coal liquefaction in which minute particles of coal in intimate contact with a hydrogenation catalyst and hydrogen arc reacted for a very short time at a temperature in excess of 400 C at a pressure of at least 1500 psi to yield over 50% liquids with a liquid to gaseous hydrocarbon ratio in excess of 8:1. 1 figures.

Control of pyrite addition in coal liquefaction process

DOEpatents

Schmid, Bruce K.; Junkin, James E.

1982-12-21

Pyrite addition to a coal liquefaction process (22, 26) is controlled (118) in inverse proportion to the calcium content of the feed coal to maximize the C.sub.5 --900.degree. F. (482.degree. C.) liquid yield per unit weight of pyrite added (110). The pyrite addition is controlled in this manner so as to minimize the amount of pyrite used and thus reduce pyrite contribution to the slurry pumping load and disposal problems connected with pyrite produced slag.

Literature survey of properties of synfuels derived from coal

NASA Technical Reports Server (NTRS)

Reynolds, T. W.; Niedzwiecki, R. W.; Clark, J. S.

1980-01-01

A literature survey of the properties of synfuels for ground-based gas turbine applications is presented. Four major concepts for converting coal into liquid fuels are described: solvent extraction, catalytic liquefaction, pyrolysis, and indirect liquefaction. Data on full range syncrudes, various distillate cuts, and upgraded products are presented for fuels derived from various processes, including H-coal, synthoil, solvent-refined coal, donor solvent, zinc chloride hydrocracking, co-steam, and flash pyrolysis. Some typical ranges of data for coal-derived low Btu gases are also presented.

Co-liquefaction of Elbistan Lignite with Manure Biomass; Part 2 - Effect of Biomass Type, Waste to Lignite Ratio and Solid to Liquid Ratio

NASA Astrophysics Data System (ADS)

Karaca, Hüseyin; Koyunoglu, Cemil

2017-12-01

Most coal hydrogenation processes require a large quantity of hydrogen. In general, a coal derived liquid such as anthracene oil was used as a hydrogen donor solvent. Tetralin, partially hydrogenated pyrene, phenantrene and coal-derived solvents, which contain hydroaromatic compounds, are efficient solvents to donate hydrogen. In an attempt to reduce the high cost of hydrogen, part of the hydrogen was replaced by a low cost hydrogen donor solvent. This must be hydrogenated during or before the process and recycled. To reduce the cost of hydrogen donor vehicles instead of liquids recycled from the liquefaction process or several biomass types, industrial by products, liquid fractions derived from oil sands bitumen were successfully used to solubilize a coal from the past. In an attempt to reduce the high cost of hydrogen, part of the hydrogen was replaced by a low cost hydrogen donor solvent. However, when hydrogen is supplied from the hydroaromatic structures present in the solvent, the activity of coal minerals is too low to rehydrogenate the solvent in-situ. Nevertheless, a decrease of using oxygen, in addition to enhanced usage of the hydrogen supply by using various waste materials might lead to a decrease of the cost of the liquefaction procedure. So instead of using tetralin another feeding material such as biomass is becoming another solution improving hydrogen donor substances. Most of the liquefaction process were carried out in a batch reactor, in which the residence time of the liquefaction products is long enough to favour the retrogressive reactions, early studies which are related to liquefaction of coal with biomass generally focus on the synergetic effects of coal while biomass added. Early studies which are related to liquefaction of coal with biomass generally focus on the synergetic effects of coal while biomass added. Alternatively, to understand the hydrogen transfer from biomass to coal, in this study, Elbistan Lignite (EL) with manure, tea pulp and waste plastic liquefied and to understand hydrogen quantity change after liquefaction, (H/C)atomic ratio of products obtained. Due to the highest oil conversion of manure biomass and highest (H/C)atomic ratio results show manure is the favourable biomass for EL amongst the other biomass used. And liquid/solid ratio optimized. About high total conversion of oil products the optimum ratio obtained as 3/1. And also EL with manure liquefied with the w/EL ratio between 0:1 to 1:1. As a result, by thinking about the yield values obtained, the optimum waste to lignite ratio found to be 1:1.

Catalysts and process developments for two-stage liquefaction. Final technical report, October 1, 1989--September 30, 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cronauer, D.C.; Swanson, A.J.; Sajkowski, D.J.

1992-12-31

Research in this project centered upon developing and evaluating catalysts and process improvements for coal liquefaction in the two-stage, close-coupled catalytic process. The major results are summarized here and they are described in more detail under each Task. In tasks for coal pretreatment and beneficiation, it was shown for coal handling that drying of both lignite or subbituminous coals using warm air, vacuum oven or exposing to air for long time was detrimental to subsequent liquefaction. Both laboratory and bench-scale beneficiations indicated that in order to achieve increased liquefaction yield for Illinois No. 6 bituminous coal, size separation with inmore » sink-float technique should be used. For subbituminous coal, the best beneficiation was aqueous SO{sub 2} treatment, which reduced mineral matter. In the case of lignite, the fines should be rejected prior to aqueous SO{sub 2} treatment and sink-float gravity separation. In liquefying coals with supported catalysts in both first and second stages, coal conversion was highest (93%) with Illinois No. 6 coal, which also had the highest total liquid yield of 80%, however, the product contained unacceptably high level of resid (30%). Both low rank coals gave lower conversion (85--87%) and liquid yields (57--59%), but lighter products (no resid). The analysis of spent first stage catalysts indicated significant sodium and calcium deposits causing severe deactivation. The second stage catalysts were in better condition showing high surface areas and low coke and metal deposits. The use of dispersed catalyst in the first stage would combat the severe deactivation.« less

Liquefaction of sub-bituminous coal

DOEpatents

Schindler, Harvey D.; Chen, James M.

1986-01-01

Sub-bituminous coal is directly liquefied in two stages by use of a liquefaction solvent containing insoluble material as well as 850.degree. F.+ material and 850.degree. F.- material derived from the second stage, and controlled temperature and conversion in the second stage. The process is in hydrogen balance.

Surfactant-assisted coal liquefaction

NASA Technical Reports Server (NTRS)

Hsu, G. C.

1977-01-01

Improved process of coal liquefaction utilizing nonaqueous surfactant has increased oil yield from 50 to about 80%. Asphaltene molecule formation of colloid particles is prevented by surfactant. Separated molecules present more surface area for hydrogenation reaction. Lower requirements for temperature, pressure, and hydrogen lead to reduction in capital and operation costs.

Iron catalyzed coal liquefaction process

DOEpatents

Garg, Diwakar; Givens, Edwin N.

1983-01-01

A process is described for the solvent refining of coal into a gas product, a liquid product and a normally solid dissolved product. Particulate coal and a unique co-catalyst system are suspended in a coal solvent and processed in a coal liquefaction reactor, preferably an ebullated bed reactor. The co-catalyst system comprises a combination of a stoichiometric excess of iron oxide and pyrite which reduce predominantly to active iron sulfide catalysts in the reaction zone. This catalyst system results in increased catalytic activity with attendant improved coal conversion and enhanced oil product distribution as well as reduced sulfide effluent. Iron oxide is used in a stoichiometric excess of that required to react with sulfur indigenous to the feed coal and that produced during reduction of the pyrite catalyst to iron sulfide.

Coal liquefaction with preasphaltene recycle

DOEpatents

Weimer, Robert F.; Miller, Robert N.

1986-01-01

A coal liquefaction system is disclosed with a novel preasphaltene recycle from a supercritical extraction unit to the slurry mix tank wherein the recycle stream contains at least 90% preasphaltenes (benzene insoluble, pyridine soluble organics) with other residual materials such as unconverted coal and ash. This subject process results in the production of asphaltene materials which can be subjected to hydrotreating to acquire a substitute for No. 6 fuel oil. The preasphaltene-predominant recycle reduces the hydrogen consumption for a process where asphaltene material is being sought.

The use of mixed pyrrhotite/pyrite catalysts for co-liquefaction of coal and waste rubber tires

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dadyburjor, D.B.; Zondlo, J.W.; Sharma, R.K.

1995-12-31

The overall objective of this research program is to determine the optimum processing conditions for tire/coal co-liquefaction. The catalysts used will be a ferric-sulfide-based materials, as well as promising catalysts from other consortium laboratories. The intent here is to achieve the maximum coal+tire conversion at the mildest conditions of temperature and pressure. Specific objectives include an investigation of the effects of time, temperature, pressure, catalyst and co-solvent on the conversion and product slate of the co-liquefaction. Accomplishments and conclusions are discussed.

Process and apparatus for coal hydrogenation

DOEpatents

Ruether, John A.

1988-01-01

In a coal liquefaction process an aqueous slurry of coal is prepared containing a dissolved liquefaction catalyst. A small quantity of oil is added to the slurry and then coal-oil agglomerates are prepared by agitation of the slurry at atmospheric pressure. The resulting mixture of agglomerates, excess water, dissolved catalyst, and unagglomerated solids is pumped to reaction pressure and then passed through a drainage device where all but a small amount of surface water is removed from the agglomerates. Sufficient catalyst for the reaction is contained in surface water remaining on the agglomerates. The agglomerates fall into the liquefaction reactor countercurrently to a stream of hot gas which is utilized to dry and preheat the agglomerates as well as deposit catalyst on the agglomerates before they enter the reactor where they are converted to primarily liquid products under hydrogen pressure.

Integrated coal cleaning, liquefaction, and gasification process

DOEpatents

Chervenak, Michael C.

1980-01-01

Coal is finely ground and cleaned so as to preferentially remove denser ash-containing particles along with some coal. The resulting cleaned coal portion having reduced ash content is then fed to a coal hydrogenation system for the production of desirable hydrocarbon gases and liquid products. The remaining ash-enriched coal portion is gasified to produce a synthesis gas, the ash is removed from the gasifier usually as slag, and the synthesis gas is shift converted with steam and purified to produce the high purity hydrogen needed in the coal hydrogenation system. This overall process increases the utilization of as-mined coal, reduces the problems associated with ash in the liquefaction-hydrogenation system, and permits a desirable simplification of a liquids-solids separation step otherwise required in the coal hydrogenation system.

Mobil process converts methanol to high-quality synthetic gasoline

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wood, A.

1978-12-11

If production of gasoline from coal becomes commercially attractive in the United States, a process under development at the Mobil Research and Development Corp. may compete with better known coal liquefaction processes. Mobil process converts methanol to high-octane, unleaded gasoline; methanol can be produced commercially from coal. If gasoline is the desired product, the Mobil process offers strong technical and cost advantages over H-coal, Exxon donor solvent, solvent-refined coal, and Fischer--Tropsch processes. The cost analysis, contained in a report to the Dept. of Energy, concludes that the Mobil process produces more-expensive liquid products than any other liquefaction process except Fischer--Tropsch.more » But Mobil's process produces ready-to-use gasoline, while the others produce oils which require further expensive refining to yield gasoline. Disadvantages and advantages are discussed.« less

Time phased alternate blending of feed coals for liquefaction

DOEpatents

Schweigharett, Frank; Hoover, David S.; Garg, Diwaker

1985-01-01

The present invention is directed to a method for reducing process performance excursions during feed coal or process solvent changeover in a coal hydroliquefaction process by blending of feedstocks or solvents over time. ,

Coal liquefaction process

DOEpatents

Wright, C.H.

1986-02-11

A process is described for the liquefaction of coal wherein raw feed coal is dissolved in recycle solvent with a slurry containing recycle coal minerals in the presence of added hydrogen at elevated temperature and pressure. The highest boiling distillable dissolved liquid fraction is obtained from a vacuum distillation zone and is entirely recycled to extinction. Lower boiling distillable dissolved liquid is removed in vapor phase from the dissolver zone and passed without purification and essentially without reduction in pressure to a catalytic hydrogenation zone where it is converted to an essentially colorless liquid product boiling in the transportation fuel range. 1 fig.

Solvent recyclability in a multistep direct liquefaction process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hetland, M.D.; Rindt, J.R.

1995-12-31

Direct liquefaction research at the Energy & Environmental Research Center (EERC) has, for a number of years, concentrated on developing a direct liquefaction process specifically for low-rank coals (LRCs) through the use of hydrogen-donating solvents and solvents similar to coal-derived liquids, the water/gas shift reaction, and lower-severity reaction conditions. The underlying assumption of all of the research was that advantage could be taken of the reactivity and specific qualities of LRCs to produce a tetrahydrofuran (THF)-soluble material that might be easier to upgrade than the soluble residuum produced during direct liquefaction of high-rank coals. A multistep approach was taken tomore » produce the THF-soluble material, consisting of (1) preconversion treatment to prepare the coal for solubilization, (2) solubilization of the coal in the solvent, and (3) polishing to complete solubilization of the remaining material. The product of these three steps can then be upgraded during a traditional hydrotreatment step. The results of the EERC`s research indicated that additional studies to develop this process more fully were justified. Two areas were targeted for further research: (1) determination of the recyclability of the solvent used during solubilization and (2) determination of the minimum severity required for hydrotreatment of the liquid product. The current project was funded to investigate these two areas.« less

Direct liquefaction proof-of-concept program. Topical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Comolli, A.G.; Lee, L.K.; Pradhan, V.R.

This report presents the results of work conducted under the DOE Proof-of-Concept Program in direct coal liquefaction at Hydrocarbon Technologies, Inc. in Lawrenceville, New Jersey, from February 1994 through April 1995. The work includes modifications to HRI`s existing 3 ton per day Process Development Unit (PDU) and completion of the second PDU run (POC Run 2) under the Program. The 45-day POC Run 2 demonstrated scale up of the Catalytic Two-Stage Liquefaction (CTSL Process) for a subbituminous Wyoming Black Thunder Mine coal to produce distillate liquid products at a rate of up to 4 barrels per ton of moisture-ash-free coal.more » The combined processing of organic hydrocarbon wastes, such as waste plastics and used tire rubber, with coal was also successfully demonstrated during the last nine days of operations of Run POC-02. Prior to the first PDU run (POC-01) in this program, a major effort was made to modify the PDU to improve reliability and to provide the flexibility to operate in several alternative modes. The Kerr McGee Rose-SR{sup SM} unit from Wilsonville, Alabama, was redesigned and installed next to the U.S. Filter installation to allow a comparison of the two solids removal systems. The 45-day CTSL Wyoming Black Thunder Mine coal demonstration run achieved several milestones in the effort to further reduce the cost of liquid fuels from coal. The primary objective of PDU Run POC-02 was to scale-up the CTSL extinction recycle process for subbituminous coal to produce a total distillate product using an in-line fixed-bed hydrotreater. Of major concern was whether calcium-carbon deposits would occur in the system as has happened in other low rank coal conversion processes. An additional objective of major importance was to study the co-liquefaction of plastics with coal and waste tire rubber with coal.« less

Catalytic coal liquefaction with treated solvent and SRC recycle

DOEpatents

Garg, Diwakar; Givens, Edwin N.; Schweighardt, Frank K.

1986-01-01

A process for the solvent refining of coal to distillable, pentane soluble products using a dephenolated and denitrogenated recycle solvent and a recycled, pentane-insoluble, solvent-refined coal material, which process provides enhanced oil-make in the conversion of coal.

Geological occurrence response to trace elemental migration in coal liquefaction based on SPSS: take no. 11 coalbed in Antaibao mine for example

NASA Astrophysics Data System (ADS)

Xia, Xiaohong; Qin, Yong; Yang, Weifeng

2013-03-01

Coal liquefaction is an adoptable method to transfer the solid fossil energy into liquid oil in large scale, but the dirty material in which will migrate to different step of liquefaction. The migration rule of some trace elements is response to the react activity of macerals in coal and the geological occurrence of the element nature of itself. In this paper, from the SPSS data correlation analysis and hierarchical clustering dendrogram about the trace elements with macerals respond to coal liquefaction yield, it shows the trace elements in No.11 Antaibao coal seam originated from some of lithophile and sulphophle elements. Correlation coefficient between liquefaction yield of three organic macerals and migration of the elements in liquefaction residue indicated that the lithophile are easy to transfer to residue, while sulphophle are apt to in the liquid products. The activated macerals are response to sulphophle trace elements. The conclusion is useful to the coal blending and environmental effects on coal direct liquefaction.

Advanced liquefaction using coal swelling and catalyst dispersion techniques. Volume 2, appendices. Final technical report, October 1, 1991--September 30, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curtis, C.W.; Chander, S.; Gutterman, C.

Liquefaction experiments were undertaken using subbituminous Black Thunder mine coal to observe the effects of aqueous SO{sub 2} coal beneficiation and the introduction of various coal swelling solvents and catalyst precursors. Aqueous SO{sub 2} beneficiation of Black Thunder coal removed alkali metals and alkaline earth metals, increased the sulfur content and increased the catalytic liquefaction conversion to THF solubles compared to untreated Black Thunder coal. The liquefaction solvent had varying effects on coal conversion, depending upon the type of solvent added. The hydrogen donor solvent, dihydroanthracene, was most effective, while a coal-derived Wilsonville solvent promoted more coal conversion than didmore » relatively inert 1-methylnaphthalene. Swelling of coal with hydrogen bonding solvents tetrahydrofuran (THF), isopropanol, and methanol, prior to reaction resulted in increased noncatalytic conversion of both untreated and SO{sub 2} treated Black Thunder coals, while dimethylsulfoxide (DMSO), which was absorbed more into the coal than any other swelling solvent, was detrimental to coal conversion. Swelling of SO{sub 2} treated coal before liquefaction resulted in the highest coal conversions; however, the untreated coal showed the most improvements in catalytic reactions when swelled in either THF, isopropanol, or methanol prior to liquefaction. The aprotic solvent DMSO was detrimental to coal conversion.« less

Process for coal liquefaction in staged dissolvers

DOEpatents

Roberts, George W.; Givens, Edwin N.; Skinner, Ronald W.

1983-01-01

There is described an improved liquefaction process by which coal is converted to a low ash and low sulfur carbonaceous material that can be used as a fuel in an environmentally acceptable manner without costly gas scrubbing equipment. In the process, coal is slurried with a pasting oil, passed through a preheater and at least two dissolvers in series in the presence of hydrogen-rich gases at elevated temperatures and pressures. Solids, including mineral ash and unconverted coal macerals, are separated from the condensed reactor effluent. In accordance with the improved process, the first dissolver is operated at a higher temperature than the second dissolver. This temperature sequence produces improved product selectivity and permits the incorporation of sufficient hydrogen in the solvent for adequate recycle operations.

Process and apparatus for coal hydrogenation

DOEpatents

Ruether, John A.; Simpson, Theodore B.

1991-01-01

In a coal liquefaction process an aqueous slurry of coal is prepared containing a dissolved liquefaction catalyst. A small quantity of oil is added to the slurry and then coal-oil agglomerates are prepared by agitation of the slurry at atmospheric pressure. The resulting mixture is drained of excess water and dried at atmospheric pressure leaving catalyst deposited on the agglomerates. The agglomerates then are fed to an extrusion device where they are formed into a continuous ribbon of extrudate and fed into a hydrogenation reactor at elevated pressure and temperature. The catalytic hydrogenation converts the extrudate primarily to liquid hydrocarbons in the reactor. The liquid drained in recovering the agglomerates is recycled.

Evaluations in support of regulatory and research decisions by the U. S. Environmental Protection Agency for the control of toxic hazards from hazardous wastes, glyphosate, dalapon, and synthetic fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scofield, R.

1984-01-01

This report includes toxicological and regulatory evaluations performed in support of U.S. EPA regulation of toxic materials and hazardous wastes. The first section of the report describes evaluations which support: (a) the regulation of small-volume generators of hazardous wastes, (b) the regulation of hazardous wastes from pesticide manufacturing, and (c) the disposal of the herbicide, silvex. The second section describes the environmental fate, transport, and effect of glyphosate and dalapon. The third section deals with synthetic fuels, including evaluations of synfuel-product toxicity, uncontrolled air emissions, and particular focus on the toxicity of products from several indirect coal liquefaction processes includingmore » methanol synthesis, Fischer-Tropsch, Mobil M-Gasoline, and Lurgi gasification technologies. Three direct coal liquefaction processes were examined for product toxicity and air emissions: Solvent Refined Coal (I and II) and the Exxon Donor Solvent Process. Also described in the third section is an evaluation of environmental and health hazards associated with the use of synthetic fuels from indirect coal liquefaction, direct coal liquefaction, and shale oil. Finally, the fourth section discusses some problems associated with performing, on a contractual basis, scientific and technical evaluations in support of U.S. EPA regulatory and research decisions.« less

Catalytic coal liquefaction with treated solvent and SRC recycle

DOEpatents

Garg, D.; Givens, E.N.; Schweighardt, F.K.

1986-12-09

A process is described for the solvent refining of coal to distillable, pentane soluble products using a dephenolated and denitrogenated recycle solvent and a recycled, pentane-insoluble, solvent-refined coal material, which process provides enhanced oil-make in the conversion of coal. 2 figs.

Co-Liquefaction of Elbistan Lignite with Manure Biomass; Part 1. Effect of Catalyst Concentration

NASA Astrophysics Data System (ADS)

Koyunoglu, Cemil; Karaca, Hüseyin

2017-12-01

The hydrogenation of coal by molecular hydrogen has not been appreciable unless a catalyst has been used, especially at temperatures below 500 °C. Conversion under these conditions is essentially the result of the pyrolysis of coal, although hydrogen increases the yield of conversion due to the stabilization of radicals and other reactive species. Curtis and his co-workers has shown that highly effective and accessible catalyst are required to achieve high levels of oil production from the coprocessing of coal and heavy residua. In their work, powdered hydrotreating catalyst at high loadings an oil-soluble metal salts of organic acids as catalyst precursors achieved the highest levels of activity for coal conversion and oil production. Red mud which is iron-based catalysed has been used in several co-processing studies. It was used as an inexpensive sulphur sink for the H2S evolved to convert Fe into pyrrohotite during coal liquefaction. In this study, Elbistan Lignite (EL) processed with manure using red mud as a catalyst with the range of concentration from 3% to 12%. The main point of using red mud catalyst is to enhance oil products yield of coal liquefaction, which deals with its catalytic activity. On the other hand, red mud acts on EL liquefaction with manure as a catalyst and represents an environmental option to produce lower sulphur content oil products as well.

Coal liquefaction process wherein jet fuel, diesel fuel and/or ASTM No. 2 fuel oil is recovered

DOEpatents

Bauman, Richard F.; Ryan, Daniel F.

1982-01-01

An improved process for the liquefaction of coal and similar solid carbonaceous materials wherein a hydrogen donor solvent or diluent derived from the solid carbonaceous material is used to form a slurry of the solid carbonaceous material and wherein the naphthenic components from the solvent or diluent fraction are separated and used as jet fuel components. The extraction increases the relative concentration of hydroaromatic (hydrogen donor) components and as a result reduces the gas yield during liquefaction and decreases hydrogen consumption during said liquefaction. The hydrogenation severity can be controlled to increase the yield of naphthenic components and hence the yield of jet fuel and in a preferred embodiment jet fuel yield is maximized while at the same time maintaining solvent balance.

Catalysts and process developments for two-stage liquefaction. First quarterly technical progress report No. 52, October 1, 1991--December 31, 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cronauer, D.C.; Swanson, A.J.; Sajkowski, D.J.

Research under way in this project centers upon developing and evaluating catalysts and process improvements for coal liquefaction in the two-stage, close-coupled catalytic process. As discussed in the previous quarterly report, the feedstock liquefaction studies for the three feedstocks (Black Thunder subbituminous coal, Martin Lake lignite, and Illinois No. 6 coal) were completed. Both Black Thunder coal and Martin Lake lignite gave lighter products than Illinois No. 6 coal at similar process conditions. Severe catalyst deactivation in the first stage was also observed with the Martin Lake lignite run. The first stage catalyst testing program was started (Task 3.2.1). Aftermore » a successful reference run with Illinois No. 6 coal, a high-temperature run with AMOCAT{trademark} 1C was completed, where the results showed that the first stage temperature should be no higher than 820{degrees}F. In addition, several runs were made both with Illinois No. 6 and Black Thunder coals using oil-soluble catalysts, Molyvan L, and molybdenum octoate in one or both stages. Overall, the results look very promising and show that dispersed molybdenum catalysts are good alternatives for Stage 1 or both 1 and 2, especially for Illinois No. 6 coal. In the case of Black Thunder coal, the conversion and yields were good, although the product quality was poorer, however, the use of slurry catalysts is still recommended.« less

Coal liquefaction process utilizing coal/CO.sub.2 slurry feedstream

DOEpatents

Comolli, Alfred G.; McLean, Joseph B.

1989-01-01

A coal hydrogenation and liquefaction process in which particulate coal feed is pressurized to an intermediate pressure of at least 500 psig and slurried with CO.sub.2 liquid to provide a flowable coal/CO.sub.2 slurry feedstream, which is further pressurized to at least 1000 psig and fed into a catalytic reactor. The coal particle size is 50-375 mesh (U.S. Sieve Series) and provides 50-80 W % coal in the coal/CO.sub.2 slurry feedstream. Catalytic reaction conditions are maintained at 650.degree.-850.degree. F. temperature, 1000-4000 psig hydrogen partial pressure and coal feed rate of 10-100 lb coal/hr ft.sup.3 reactor volume to produce hydrocarbon gas and liquid products. The hydrogen and CO.sub.2 are recovered from the reactor effluent gaseous fraction, hydrogen is recycled to the catalytic reactor, and CO.sub.2 is liquefied and recycled to the coal slurrying step. If desired, two catalytic reaction stages close coupled together in series relation can be used. The process advantageously minimizes the recycle and processing of excess hydrocarbon liquid previously needed for slurrying the coal feed to the reactor(s).

Coal liquefaction in an inorganic-organic medium. [DOE patent application

DOEpatents

Vermeulen, T.; Grens, E.A. II; Holten, R.R.

Improved process for liquefaction of coal by contacting pulverized coal in an inorganic-organic medium solvent system containing a ZnCl/sub 2/ catalyst, a polar solvent with the structure RX where X is one of the elements O, N, S, or P, and R is hydrogen or a lower hydrocarbon radical; the solvent system can contain a hydrogen donor solvent (and must when RX is water) which is immiscible in the ZnCl/sub 2/ and is a hydroaromatic hydrocarbon selected from tetralin, dihydrophenanthrene, dihydroanthracene or a hydrogenated coal derived hydroaromatic hydrocarbon distillate fraction.

Integration of stripping of fines slurry in a coking and gasification process

DOEpatents

DeGeorge, Charles W.

1980-01-01

In an integrated fluid coking and gasification process wherein a stream of fluidized solids is passed from a fluidized bed coking zone to a second fluidized bed and wherein entrained solid fines are recovered by a wet scrubbing process and wherein the resulting solids-liquid slurry is stripped to remove acidic gases, the stripped vapors of the stripping zone are sent to the gas cleanup stage of the gasification product gas. The improved stripping integration is particularly useful in the combination coal liquefaction process, fluid coking of bottoms of the coal liquefaction zone and gasification of the product coke.

Surfactant studies for bench-scale operation

NASA Technical Reports Server (NTRS)

Hickey, Gregory S.; Sharma, Pramod K.

1993-01-01

A phase 2 study has been initiated to investigate surfactant-assisted coal liquefaction, with the objective of quantifying the enhancement in liquid yields and product quality. This report covers the second quarter of work. The major accomplishments were: completion of coal liquefaction autoclave reactor runs with Illinois number 6 coal at processing temperatures of 300, 325, and 350 C, and pressures of 1800 psig; analysis of the filter cake and the filtrate obtained from the treated slurry in each run; and correlation of the coal conversions and the liquid yield quality to the surfactant concentration. An increase in coal conversions and upgrading of the liquid product quality due to surfactant addition was observed for all runs.

A Course in Fundamentals of Coal Utilization and Conversion Processes.

ERIC Educational Resources Information Center

Radovic, Ljubisa R.

1985-01-01

Describes the content, objectives, and requirements for a one-semester (30 20-hour sessions) graduate engineering course at the University of Concepcion, Chile. Major course topics include: structure and properties of coal; coal pyrolysis and carbonization; coal liquefaction; coal combustion and gasification; and economic and environmental…

Process for improving soluble coal yield in a coal deashing process

DOEpatents

Rhodes, Donald E.

1980-01-01

Coal liquefaction products are contacted with a deashing solvent and introduced into a first separation zone. The first separation zone is maintained at an elevated temperature and pressure, determined to maximize the recovery of soluble coal products, to cause said coal liquefaction products to separate into a first light phase and a first heavy phase. Under these conditions the heavy phase while still fluid-like in character is substantially non-flowable. Flowability is returned to the fluid-like heavy phase by the introduction of an additional quantity of deashing solvent into the first separation zone at a location below the interface between the first light and heavy phases or into the heavy phase withdrawal conduit during withdrawal of the first heavy phase and prior to any substantial pressure reduction. The first heavy phase then is withdrawn from the first separation zone for additional downstream processing without plugging either the withdrawal conduit or the downstream apparatus. The first light phase comprising the soluble coal products is withdrawn and recovered in an increased yield to provide a more economical coal deashing process.

Hydrogen Transfer during Liquefaction of Elbistan Lignite to Biomass; Total Reaction Transformation Approach

NASA Astrophysics Data System (ADS)

Koyunoglu, Cemil; Karaca, Hüseyin

2017-12-01

Given the high cost of the tetraline solvent commonly used in liquefaction, the use of manure with EL is an important factor when considering the high cost of using tetraline as a hydrogen transfer source. In addition, due to the another cost factor which is the catalyst prices, red mud (commonly used, produced as a byproduct in the production of aluminium) is reduced cost in the work of liquefaction of coal, biomass, even coal combined biomass, corresponding that making the EL liquefaction an agenda for our country is another important factor. Conditions for liquefaction experiments conducted for hydrogen transfer from manure to coal; Catalyst concentration of 9%, liquid/solid ratio of 3/1, reaction time of 60 min, fertilizer/lignite ratio of 1/3, and the reaction temperature of 400 °C, the stirred speed of 400 rpm and the initial nitrogen pressure of 20 bar was fixed. In order to demonstrate the hydrogen, transfer from manure to coal, coal is used solely, by using tetraline (also known as a hydrogen carrier) and distilled water which is not hydrogen donor as a solvent in the co-liquefaction of experiments, and also the liquefaction conditions are carried out under an inert (N2) gas atmosphere. According to the results of the obtained liquefaction test; using tetraline solvent the total liquid product conversion percentage of the oil + gas conversion was 38.3 %, however, the results of oil+gas conversion obtained using distilled water and EL combined with manure the total liquid product conversion percentage was 7.4 %. According to the results of calorific value and elemental analysis, only the ratio of (H/C)atomic of coal obtained by using tetraline increased with the liquefaction of manure and distilled water. The reason of the increase in the amount of hydrogen due to hydrogen transfer from the manure on the solid surface of the coal, and also on the surface of the inner pore of the coal during the liquefaction, brings about the evaluation of the coal as a structure involved in the recycling through the liquefaction plant if it is being installed. As a result of this study, results obtained from oil + gas data shows that when distilled water is used instead of tetraline during liquefaction of EL combined with manure, abundant crude hydrogen transfer takes place not because of using distilled water as a solvent but only with manure considered as a hydrogen sources. Furthermore, while adding manure into coal of liquefaction is also an alternative for current oil production.

Advanced Coal Liquefaction Research and Development Facility, Wilsonville, Alabama. Run 260 with Black Thunder Mine subbituminous coal: Technical progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This report presents the results of Run 260 performed at the Advanced Coal Liquefaction R&D Facility in Wilsonville. The run was started on July 17, 1990 and continued until November 14, 1990, operating in the Close-Coupled Integrated Two-Stage Liquefaction mode processing Black Thunder mine subbituminous coal (Wyodak-Anderson seam from Wyoming Powder River Basin). Both thermal/catalytic and catalytic/thermal tests were performed to determine the methods for reducing solids buildup in a subbituminous coal operation, and to improve product yields. A new, smaller interstage separator was tested to reduce solids buildup by increasing the slurry space velocity in the separator. In ordermore » to obtain improved coal and resid conversions (compared to Run 258) full-volume thermal reactor and 3/4-volume catalytic reactor were used. Shell 324 catalyst, 1/16 in. cylindrical extrudate, at a replacement rate of 3 lb/ton of MF coal was used in the catalytic stage. Iron oxide was used as slurry catalyst at a rate of 2 wt % MF coal throughout the run. (TNPS was the sulfiding agent.)« less

Catalytic coal hydroliquefaction process

DOEpatents

Garg, Diwakar

1984-01-01

A process is described for the liquefaction of coal in a hydrogen donor solvent in the presence of hydrogen and a co-catalyst combination of iron and a Group VI or Group VIII non-ferrous metal or compounds of the catalysts.

Integration of advanced preparation with coal liquefaction. Second quarterly technical progress report, January 1-March 31, 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steedman, W.G.; Longanbach, J.R.; Muralidhara, H.S.

Standard reaction conditions of 427 C, 5 minutes reaction time, 2:1 solvent/coal ratio and 1000 psig (r.t.) hydrogen overpressure result in good, but not maximum, conversions to THF soluble with both Illinois No. 6 and Wyodak (upper seam) coals. The cumulative effects of the pretreatment steps were also examined using feedstocks which were dried in a vacuum oven at room temperature under nitrogen before liquefaction to remove the effects of moisture. Chloride removal followed by drying had a positive effect on liquefaction. Oil agglomeration followed by drying also improved liquefaction reactivity significantly. Solvent drying also resulted in a small increasemore » in liquefaction reactivity. The overall reactivity of coal treated in sequence with each pretreatment step was slightly less than that of the dry ground coal. Liquefaction under a high partial pressure of hydrogen sulfide in hydrogen also results in a significant increase in conversion to THF solubles. 1 reference, 12 figures, 7 tables.« less

Minimizing corrosion in coal liquid distillation

DOEpatents

Baumert, Kenneth L.; Sagues, Alberto A.; Davis, Burtron H.

1985-01-01

In an atmospheric distillation tower of a coal liquefaction process, tower materials corrosion is reduced or eliminated by introduction of boiling point differentiated streams to boiling point differentiated tower regions.

Liquid fuels from coal: analysis of a partial transition from oil to coal; light liquids in Zimbabwe's liquid fuels base

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maya, R.S.

1986-01-01

This study assesses the feasibility of a coal based light liquids program as a way to localize forces that determine the flow of oil into the Zimbabwean economy. Methods in End-use Energy Analysis and Econometrics in which the utilization of petroleum energy is related to economic and industrial activity are used to gain insight into the structure and behavior of petroleum utilization in that country and to forecast future requirements of this resource. The feasibility of coal liquefaction as a substitute for imported oil is assessed by the use of engineering economics in which the technical economics of competing oilmore » supply technologies are analyzed and the best option is selected. Coal conversion technologies are numerous but all except the Fischer-Trosch indirect coal liquefaction technology are deficient in reliability as commercial ventures. The Fischer-Tropsch process by coincidence better matches Zimbabwe's product configuration than the less commercially advanced technologies. Using present value analysis to compare the coal liquefaction and the import option indicates that it is better to continue importing oil than to resort to a coal base for a portion of the oil supplies. An extended analysis taking special consideration of the risk and uncertainty factors characteristic of Zimbabwe's oil supply system indicates that the coal option is better than the import option. The relative infancy of the coal liquefaction industry and the possibility that activities responsible for the risk and uncertainty in the oil supply system will be removed in the future, however, make the adoption of the coal option an unusually risky undertaking.« less

Technology for advanced liquefaction processes: Coal/waste coprocessing studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cugini, A.V.; Rothenberger, K.S.; Ciocco, M.V.

1995-12-31

The efforts in this project are directed toward three areas: (1) novel catalyst (supported and unsupported) research and development, (2) study and optimization of major operating parameters (specifically pressure), and (3) coal/waste coprocessing. The novel catalyst research and development activity has involved testing supported catalysts, dispersed catalysts, and use of catalyst testing units to investigate the effects of operating parameters (the second area) with both supported and unsupported catalysts. Several supported catalysts were tested in a simulated first stage coal liquefaction application at 404{degrees}C during this performance period. A Ni-Mo hydrous titanate catalyst on an Amocat support prepared by Sandiamore » National laboratories was tested. Other baseline experiments using AO-60 and Amocat, both Ni-Mo/Al{sub 2}O{sub 3} supported catalysts, were also made. These experiments were short duration (approximately 12 days) and monitored the initial activity of the catalysts. The results of these tests indicate that the Sandia catalyst performed as well as the commercially prepared catalysts. Future tests are planned with other Sandia preparations. The dispersed catalysts tested include sulfated iron oxide, Bayferrox iron oxide (iron oxide from Miles, Inc.), and Bailey iron oxide (micronized iron oxide from Bailey, Inc.). The effects of space velocity, temperature, and solvent-to-coal ratio on coal liquefaction activity with the dispersed catalysts were investigated. A comparison of the coal liquefaction activity of these catalysts relative to iron catalysts tested earlier, including FeOOH-impregnated coal, was made. These studies are discussed.« less

One-Step Coal Liquefaction

NASA Technical Reports Server (NTRS)

Qader, S. A.

1984-01-01

Steam injection improves yield and quality of product. Single step process for liquefying coal increases liquid yield and reduces hydrogen consumption. Principal difference between this and earlier processes includes injection of steam into reactor. Steam lowers viscosity of liquid product, so further upgrading unnecessary.

Simulation models and designs for advanced Fischer-Tropsch technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, G.N.; Kramer, S.J.; Tam, S.S.

1995-12-31

Process designs and economics were developed for three grass-roots indirect Fischer-Tropsch coal liquefaction facilities. A baseline and an alternate upgrading design were developed for a mine-mouth plant located in southern Illinois using Illinois No. 6 coal, and one for a mine-mouth plane located in Wyoming using Power River Basin coal. The alternate design used close-coupled ZSM-5 reactors to upgrade the vapor stream leaving the Fischer-Tropsch reactor. ASPEN process simulation models were developed for all three designs. These results have been reported previously. In this study, the ASPEN process simulation model was enhanced to improve the vapor/liquid equilibrium calculations for themore » products leaving the slurry bed Fischer-Tropsch reactors. This significantly improved the predictions for the alternate ZSM-5 upgrading design. Another model was developed for the Wyoming coal case using ZSM-5 upgrading of the Fischer-Tropsch reactor vapors. To date, this is the best indirect coal liquefaction case. Sensitivity studies showed that additional cost reductions are possible.« less

Coal liquefaction process

DOEpatents

Skinner, Ronald W.; Tao, John C.; Znaimer, Samuel

1985-01-01

This invention relates to an improved process for the production of liquid carbonaceous fuels and solvents from carbonaceous solid fuels, especially coal. The claimed improved process includes the hydrocracking of the light SRC mixed with a suitable hydrocracker solvent. The recycle of the resulting hydrocracked product, after separation and distillation, is used to produce a solvent for the hydrocracking of the light solvent refined coal.

Coal-oil coprocessing at HTI - development and improvement of the technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stalzer, R.H.; Lee, L.K.; Hu, J.

1995-12-31

Co-Processing refers to the combined processing of coal and petroleum-derived heavy oil feedstocks. The coal feedstocks used are those typically utilized in direct coal liquefaction: bituminous, subbituminous, and lignites. Petroleum-derived oil, is typically a petroleum residuum, containing at least 70 W% material boiling above 525{degrees}C. The combined coal and oil feedstocks are processed simultaneously with the dual objective of liquefying the coal and upgrading the petroleum-derived residuum to lower boiling (<525{degrees}C) premium products. HTI`s investigation of the Co-Processing technology has included work performed in laboratory, bench and PDU scale operations. The concept of co-processing technology is quite simple and amore » natural outgrowth of the work done with direct coal liquefaction. A 36 month program to evaluate new process concepts in coal-oil coprocessing at the bench-scale was begun in September 1994 and runs until September 1997. Included in this continuous bench-scale program are provisions to examine new improvements in areas such as: interstage product separation, feedstock concentrations (coal/oil), improved supported/dispersed catalysts, optimization of reactor temperature sequencing, and in-line hydrotreating. This does not preclude other ideas from DOE contracts and other sources that can lead to improved product quality and economics. This research work has led to important findings which significantly increased liquid yields, improved product quality, and improved process economics.« less

Filtering coal-derived oil through a filter media precoated with particles partially solubilized by said oil

DOEpatents

Rodgers, Billy R.; Edwards, Michael S.

1977-01-01

Solids such as char, ash, and refractory organic compounds are removed from coal-derived liquids from coal liquefaction processes by the pressure precoat filtration method using particles of 85-350 mesh material selected from the group of bituminous coal, anthracite coal, lignite, and devolatilized coals as precoat materials and as body feed to the unfiltered coal-derived liquid.

Coal liquefaction process using pretreatment with a binary solvent mixture

DOEpatents

Miller, R.N.

1986-10-14

An improved process for thermal solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a hydrogen donor solvent comprises pretreating the coal with a binary mixture of an aromatic hydrocarbon and an aliphatic alcohol at a temperature below 300 C before the hydroliquefaction step. This treatment generally increases both conversion of coal and yields of oil. 1 fig.

Coal liquefaction process using pretreatment with a binary solvent mixture

DOEpatents

Miller, Robert N.

1986-01-01

An improved process for thermal solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a hydrogen donor solvent comprises pretreating the coal with a binary mixture of an aromatic hydrocarbon and an aliphatic alcohol at a temperature below 300.degree. C. before the hydroliquefaction step. This treatment generally increases both conversion of coal and yields of oil.

Desulfurizing Coal With an Alkali Treatment

NASA Technical Reports Server (NTRS)

Ravindram, M.; Kalvinskas, J. J.

1987-01-01

Experimental coal-desulfurization process uses alkalies and steam in fluidized-bed reactor. With highly volatile, high-sulfur bituminous coal, process removed 98 percent of pyritic sulfur and 47 percent of organic sulfur. Used in coal liquefaction and in production of clean solid fuels and synthetic liquid fuels. Nitrogen or steam flows through bed of coal in reactor. Alkalies react with sulfur, removing it from coal. Nitrogen flow fluidizes bed while heating or cooling; steam is fluidizing medium during reaction.

Non-catalytic transfer hydrogenation in supercritical CO2 for coal liquefaction

NASA Astrophysics Data System (ADS)

Elhussien, Hussien

This thesis presents the results of the investigation on developing and evaluating a low temperature (<150°C) non - catalytic process using a hydrogen transfer agent (instead of molecu-lar hydrogen) for coal dissolution in supercritical CO2. The main idea behind the thesis was that one hydrogen atom from water and one hydrogen atom from the hydrogen transfer agent (HTA) were used to hydrogenate the coal. The products of coal dissolution were non-polar and polar while the supercritical CO2, which enhanced the rates of hydrogenation and dissolution of the non-polar molecules and removal from the reaction site, was non-polar. The polar modifier (PM) for CO2 was added to the freed to aid in the dissolution and removal of the polar components. The addition of a phase transfer agent (PTA) allowed a seamless transport of the ions and by-product between the aqueous and organic phases. DDAB, used as the PTA, is an effective phase transfer catalyst and showed enhancement to the coal dissolution process. COAL + DH- +H 2O → COAL.H2 + DHO-- This process has a great feature due to the fact that the chemicals were obtained without requir-ing to first convert coal to CO and H2 units as in indirect coal liquefaction. The experiments were conducted in a unique reactor set up that can be connected through two lines. one line to feed the reactor with supercritical CO 2 and the other connected to gas chromatograph. The use of the supercritical CO2 enhanced the solvent option due to the chemical extraction, in addition to the low environmental impact and energy cost. In this thesis the experiment were conducted at five different temperatures from atmos-pheric to 140°C, 3000 - 6000 psi with five component of feed mixture, namely water, HTA, PTA, coal, and PM in semi batch vessels reactor system with a volume of 100 mL. The results show that the chemicals were obtained without requiring to first convert coal to CO and H2 units as in indirect coal liquefaction. The results show that the conversion was found to be 91.8% at opti-mum feed mixtures values of 3, 1.0 and 5.4 for water: PM, HTA: coal, water: coal respectively. With the oil price increase and growing in energy demand, the coal liquefaction remain affordable and available energy alternative.

Thermolysis of phenethyl phenyl ether: A model of ether linkages in low rank coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Britt, P.F.; Buchanan, A.C. III; Malcolm, E.A.

Currently, an area of interest and frustration for coal chemists has been the direct liquefaction of low rank coal. Although low rank coals are more reactive than bituminous coals, they are more difficult to liquefy and offer lower liquefaction yields under conditions optimized for bituminous coals. Solomon, Serio, and co-workers have shown that: in the pyrolysis and liquefaction of low rank coals, a low temperature cross-linking reaction associated with oxygen functional groups occurs before tar evolution. A variety of pretreatments (demineralization, alkylation, and ion-exchange) have been shown to reduce these retrogressive reactions and increase tar yields, but the actual chemicalmore » reactions responsible for these processes have not been defined. In order to gain insight into the thermochemical reactions leading to cross-linking in low rank coal, we have undertaken a study of the pyrolysis of oxygen containing coal model compounds. Solid state NMR studies suggest that the alkyl aryl ether linkage may be present in modest amounts in low rank coal. Therefore, in this paper, we will investigate the thermolysis of phenethyl phenyl ether (PPE) as a model of 0-aryl ether linkages found in low rank coal, lignites, and lignin, an evolutionary precursor of coal. Our results have uncovered a new reaction channel that can account for 25% of the products formed. The impact of reaction conditions, including restricted mass transport, on this new reaction pathway and the role of oxygen functional groups in cross-linking reactions will be investigated.« less

CAMD studies of coal structure and coal liquefaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faulon, J.L.; Carlson, G.A.

The macromolecular structure of coal is essential to understand the mechanisms occurring during coal liquefaction. Many attempts to model coal structure can be found in the literature. More specifically for high volatile bituminous coal, the subject of interest the most commonly quoted models are the models of Given, Wiser, Solomon, and Shinn. In past work, the authors`s have used computer-aided molecular design (CAMD) to develop three-dimensional representations for the above coal models. The three-dimensional structures were energy minimized using molecular mechanics and molecular dynamics. True density and micopore volume were evaluated for each model. With the exception of Given`s model,more » the computed density values were found to be in agreement with the corresponding experimental results. The above coal models were constructed by a trial and error technique consisting of a manual fitting of the-analytical data. It is obvious that for each model the amount of data is small compared to the actual complexity of coal, and for all of the models more than one structure can be built. Hence, the process by which one structure is chosen instead of another is not clear. In fact, all the authors agree that the structure they derived was only intended to represent an {open_quotes}average{close_quotes} coal model rather than a unique correct structure. The purpose of this program is further develop CAMD techniques to increase the understanding of coal structure and its relationship to coal liquefaction.« less

Direct liquefaction proof-of-concept facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alfred G. Comolli; Peizheng Zhou; HTI Staff

2000-01-01

The main objective of the U.S. DOE, Office of Fossil Energy, is to ensure the US a secure energy supply at an affordable price. An integral part of this program was the demonstration of fully developed coal liquefaction processes that could be implemented if market and supply considerations so required, Demonstration of the technology, even if not commercialized, provides a security factor for the country if it is known that the coal to liquid processes are proven and readily available. Direct liquefaction breaks down and rearranges complex hydrocarbon molecules from coal, adds hydrogen, and cracks the large molecules to thosemore » in the fuel range, removes hetero-atoms and gives the liquids characteristics comparable to petroleum derived fuels. The current processes being scaled and demonstrated are based on two reactor stages that increase conversion efficiency and improve quality by providing the flexibility to adjust process conditions to accommodate favorable reactions. The first stage conditions promote hydrogenation and some oxygen, sulfur and nitrogen removal. The second stage hydrocracks and speeds the conversion to liquids while removing the remaining sulfur and nitrogen. A third hydrotreatment stage can be used to upgrade the liquids to clean specification fuels.« less

New catalysts for coal liquefaction and new nanocrystalline catalysts synthesis methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Linehan, J.C.; Matson, D.W.; Darab, J.G.

1994-09-01

The use of coal as a source of transportation fuel is currently economically unfavorable due to an abundant world petroleum supply and the relatively high cost of coal liquefaction. Consequently, a reduction in the cost of coal liquefaction, for example by using less and/or less costly catalysts or lower liquefaction temperatures, must be accomplished if coal is to play an significant role as a source of liquid feedstock for the petrochemical industry. The authors and others have investigated the applicability of using inexpensive iron-based catalysts in place of more costly and environmentally hazardous metal catalysts for direct coal liquefaction. Iron-basedmore » catalysts can be effective in liquefying coal and in promoting carbon-carbon bond cleavage in model compounds. The authors have been involved in an ongoing effort to develop and optimize iron-based powders for use in coal liquefaction and related petrochemical applications. Research efforts in this area have been directed at three general areas. The authors have explored ways to optimize the effectiveness of catalyst precursor species through use of nanocrystalline materials and/or finely divided powders. In this effort, the authors have developed two new nanophase material production techniques, Modified Reverse Micelle (MRM) and the Rapid Thermal Decomposition of precursors in Solution (RTDS). A second effort has been aimed at optimizing the effectiveness of catalysts by variations in other factors. To this, the authors have investigated the effect that the crystalline phase has on the capacity of iron-based oxide and oxyhydroxide powders to be effectively converted to an active catalyst phase under liquefaction conditions. And finally, the authors have developed methods to produce active catalyst precursor powders in quantities sufficient for pilot-scale testing. Major results in these three areas are summarized.« less

Catalytic two-stage coal hydrogenation and hydroconversion process

DOEpatents

MacArthur, James B.; McLean, Joseph B.; Comolli, Alfred G.

1989-01-01

A process for two-stage catalytic hydrogenation and liquefaction of coal to produce increased yields of low-boiling hydrocarbon liquid and gas products. In the process, the particulate coal is slurried with a process-derived liquid solvent and fed at temperature below about 650.degree. F. into a first stage catalytic reaction zone operated at conditions which promote controlled rate liquefaction of the coal, while simultaneously hydrogenating the hydrocarbon recycle oils at conditions favoring hydrogenation reactions. The first stage reactor is maintained at 650.degree.-800.degree. F. temperature, 1000-4000 psig hydrogen partial pressure, and 10-60 lb coal/hr/ft.sup.3 reactor space velocity. The partially hydrogenated material from the first stage reaction zone is passed directly to the close-coupled second stage catalytic reaction zone maintained at a temperature at least about 25.degree. F. higher than for the first stage reactor and within a range of 750.degree.-875.degree. F. temperature for further hydrogenation and thermal hydroconversion reactions. By this process, the coal feed is successively catalytically hydrogenated and hydroconverted at selected conditions, which results in significantly increased yields of desirable low-boiling hydrocarbon liquid products and minimal production of undesirable residuum and unconverted coal and hydrocarbon gases, with use of less energy to obtain the low molecular weight products, while catalyst life is substantially increased.

Continuous bench-scale slurry catalyst testing direct coal liquefaction rawhide sub-bituminous coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauman, R.F.; Coless, L.A.; Davis, S.M.

In 1992, the Department of Energy (DOE) sponsored research to demonstrate a dispersed catalyst system using a combination of molybdenum and iron precursors for direct coal liquefaction. This dispersed catalyst system was successfully demonstrated using Black Thunder sub-bituminous coal at Wilsonville, Alabama by Southern Electric International, Inc. The DOE sponsored research continues at Exxon Research and Development Laboratories (ERDL). A six month continuous bench-scale program using ERDL`s Recycle Coal Liquefaction Unit (RCLU) is planned, three months in 1994 and three months in 1995. The initial conditions in RCLU reflect experience gained from the Wilsonville facility in their Test Run 263.more » Rawhide sub-bituminous coal which is similar to the Black Thunder coal tested at Wilsonville was used as the feed coal. A slate of five dispersed catalysts for direct coal liquefaction of Rawhide sub-bituminous coal has been tested. Throughout the experiments, the molybdenum addition rate was held constant at 100 wppm while the iron oxide addition rate was varied from 0.25 to 1.0 weight percent (dry coal basis). This report covers the 1994 operations and accomplishments.« less

Continuous bench-scale slurry catalyst testing direct coal liquefaction of rawhide sub-bituminous coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauman, R.F.; Coless, L.A.; Davis, S.M.

In 1992, the Department of Energy (DOE) sponsored research to demonstrate a dispersed catalyst system using a combination of molybdenum and iron precursors for direct coal liquefaction. This dispersed catalyst system was successfully demonstrated using Black Thunder sub-bituminous coal at Wilsonville, Alabama by Southern Electric International, Inc. The DOE sponsored research continues at Exxon Research and Development Laboratories (ERDL). A six month continuous bench-scale program using ERDL`s Recycle Coal Liquefaction Unit (RCLU) is planned, three months in 1994 and three months in 1995. The initial conditions in RCLU reflect experience gained from the Wilsonville facility in their Test Run 263.more » Rawhide sub-bituminous coal which is similar to the Black Thunder coal tested at Wilsonville was used as the feed coal. A slate of five dispersed catalysts for direct coal liquefaction of Rawhide sub-bituminous coal has been tested. Throughout the experiments, the molybdenum addition rate was held constant at 100 wppm while the iron oxide addition rate was varied from 0.25 to 1.0 weight percent (dry coal basis). This report covers the 1994 operations and accomplishments.« less

Catalytic two-stage coal liquefaction process having improved nitrogen removal

DOEpatents

Comolli, Alfred G.

1991-01-01

A process for catalytic multi-stage hydrogenation and liquefaction of coal to produce high yields of low-boiling hydrocarbon liquids containing low concentrations of nitogen compounds. First stage catalytic reaction conditions are 700.degree.-800.degree. F. temperature, 1500-3500 psig hydrogen partial pressure, with the space velocity maintained in a critical range of 10-40 lb coal/hr ft.sup.3 catalyst settled volume. The first stage catalyst has 0.3-1.2 cc/gm total pore volume with at least 25% of the pore volume in pores having diameters of 200-2000 Angstroms. Second stage reaction conditions are 760.degree.-870.degree. F. temperature with space velocity exceeding that in the first stage reactor, so as to achieve increased hydrogenation yield of low-boiling hydrocarbon liquid products having at least 75% removal of nitrogen compounds from the coal-derived liquid products.

Donor solvent coal liquefaction with bottoms recycle at elevated pressure

DOEpatents

Bauman, Richard F.; Taunton, John W.; Anderson, George H.; Trachte, Ken L.; Hsia, Steve J.

1982-01-01

An improved process for liquefying solid carbonaceous materials wherein increased naphtha yields are achieved by effecting the liquefaction at a pressure within the range from about 1750 to about 2800 psig in the presence of recycled bottoms and a hydrogen-donor solvent containing at least 0.8 wt % donatable hydrogen. The liquefaction is accomplished at a temperature within the range from about 700.degree. to about 950.degree. F. The coal:bottoms ratio in the feed to liquefaction will be within the range from about 1:1 to about 5:1 and the solvent or diluent to total solids ratio will be at least 1.5:1 and preferably within the range from about 1.6:1 to about 3:1. The yield of naphtha boiling range materials increases as the pressure increases but generally reaches a maximum at a pressure within the range from about 2000 to about 2500 psig.

Catalysts and process developments for two-stage liquefaction. Quarterly technical progress report, January 1, 1991--March 31, 1991, report No. 40

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cronauer, D.C.; Swanson, A.J.; Sajkowski, D.J.

Research under way in this project centers upon developing and evaluating catalysts and process improvements for coal liquefaction in the two-stage close-coupled catalytic process. Further experimentation was undertaken in a continuous flow unit with Black Thunder coal, where the primary goal was to determine the extent of decarboxylation and changes in the structure of the unconverted coal samples. The preliminary results indicated little conversion of the feed coal to THF solubles at 600{degrees}F, although the conversion did increase with increasing temperature up to 24% at 700{degrees}F. The level of decarboxylation was also low at the above reaction temperatures. Thus, presoakingmore » in a coal-derived solvent or even tetralin does not seem to be an effective means to achieve decarboxylation. Feedstock liquefaction studies were done with Martin Lake lignite in a two-stage continuous flow unit. Conversion to THF solubles was 82-87%. The Martin Lake lignite product was very light and no resid was produced. Sulfur levels in the product were low, although nitrogen levels were relatively high, requiring further processing by hydrotreating. An air-oxidized sample of Martin Lake lignite produced high oxygen containing resid at the expense of distillate, which clearly indicates that air oxidation of lignite is detrimental. The spent catalyst from the first stage was severely deactivated and generally, the spent catalysts from both stages were in worse condition than those from a previous run with Black Thunder coal. The completed testing results of Sandia`s NiMo/hydrous titanate oxide (NiMo/HTO) preparations are reported.« less

Subtask 3.9 - Direct Coal Liquefaction Process Development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aulich, Ted; Sharma, Ramesh

The Energy and Environmental Research Center (EERC), in partnership with the U.S. Department of Energy (DOE) and Accelergy Corporation, an advanced fuels developer with technologies exclusively licensed from ExxonMobil, undertook Subtask 3.9 to design, build, and preliminarily operate a bench-scale direct coal liquefaction (DCL) system capable of converting 45 pounds/hour of pulverized, dried coal to a liquid suitable for upgrading to fuels and/or chemicals. Fabrication and installation of the DCL system and an accompanying distillation system for off-line fractionation of raw coal liquids into 1) a naphtha middle distillate stream for upgrading and 2) a recycle stream was completed inmore » May 2012. Shakedown of the system was initiated in July 2012. In addition to completing fabrication of the DCL system, the project also produced a 500-milliliter sample of jet fuel derived in part from direct liquefaction of Illinois No. 6 coal, and submitted the sample to the Air Force Research Laboratory (AFRL) at Wright Patterson Air Force Base, Dayton, Ohio, for evaluation. The sample was confirmed by AFRL to be in compliance with all U.S. Air Force-prescribed alternative aviation fuel initial screening criteria.« less

Rationale for continuing R&D in indirect coal liquefaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gray, D.; Tomlinson, G.

1995-12-31

The objective of this analysis is to use the world energy demand/supply model developed at MITRE to examine future liquid fuels supply scenarios both for the world and for the United States. This analysis has determined the probable extent of future oil resource shortages and the likely time frame in which the shortages will occur. The role that coal liquefaction could play in helping to alleviate this liquid fuels shortfall is also examined. The importance of continuing R&D to improve process performance and reduce the costs of coal-derived transportation fuel is quantified in terms of reducing the time when coalmore » liquids will become competitive with petroleum.« less

Heterofunctionality interaction with donor solvent coal liquefaction. Final progress report, August 1982-April 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cronauer, D.C.

1984-05-01

This project was undertaken to understand the role of the coal liquefaction solvent through a study of the interaction between the hydrogen donor solvent characteristics and the heterofunctionality of the solvent. Specifically, hydroxyl- and nitrogen-containing solvents were studied and characterized. A series of coal liquefaction experiments were carried out at 450/sup 0/C in a continuous feed stirred-tank reactor (CSTR) to observe the effect of adding phenolics to anthracene oil (AO) and SRC-II recycle solvents. The addition of phenol to AO at a ratio of 5/65 resulted in a nominal increase in coal conversion to THF solubles, but the amount ofmore » asphaltenes more than doubled resulting in a sizable net loss of solvent. The addition of m-cresol to both AO and SRC-II solvents had a positive effect on coal conversion to both THF and pentane solubles (oils). The partial removal of an OH-concentrate from SRC-II solvent was carried out using Amberlyst IRA-904 ion exchange resin. The resin-treated oil was only marginally better than raw SRC-II recycle solvent for coal liquefaction. Hydroaromatics having nitrogen functionality should be good solvents for coal liquefaction considering their effective solvent power, ability to penetrate and swell coal, and their ability to readily transfer hydrogen, particularly in the presence of oxygen functionality. However, these benefits are overshadowed by the strong tendency of the nitrogen-containing species to adduct with themselves and coal-derived materials.« less

Catalytic coal liquefaction process

DOEpatents

Garg, D.; Sunder, S.

1986-12-02

An improved process for catalytic solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a solvent comprises using as catalyst a mixture of a 1,2- or 1,4-quinone and an alkaline compound, selected from ammonium, alkali metal, and alkaline earth metal oxides, hydroxides or salts of weak acids. 1 fig.

Catalytic coal liquefaction process

DOEpatents

Garg, Diwakar; Sunder, Swaminathan

1986-01-01

An improved process for catalytic solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a solvent comprises using as catalyst a mixture of a 1,2- or 1,4-quinone and an alkaline compound, selected from ammonium, alkali metal, and alkaline earth metal oxides, hydroxides or salts of weak acids.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Prior to 1978, the Wilsonville Advanced Coal Liquefaction facility material balance surrounded only the thermal liquefaction unit and involved analyses of only the slurry stream and individual gas streams. The distillate solvent yield was determined by difference. Subsequently, several modifications and additional process units were introduced to this single unit system. With the inclusion of the deashing unit in 1978 and the catalytic hydrogenation unit in 1981, the process has evolved into a sophisticated two-stage coal liquefaction process and has the potential for various modes of integration. This report presents an elemental balancing procedure and a simplified presentation format thatmore » is sufficiently flexible to meet current and future needs. The development of the elemental balancing technique and the relevant computer programs to handle the calculations have been addressed. This will be useful in modelling individual unit performance as well as determining the impact of each unit on the overall liquefaction system, provided the units are on a steady-state basis. Five different material balance envelopes are defined. Three of these envelopes pertain to the individual units (the thermal liquefaction or TL unit, the Critical Solvent Deashing or CSD unit and the H-Oil Ebullated Bed Hydrotreating or HTR unit). The fourth or single stage material balance envelope combines the TL and CSD units. The fifth envelope is the two-stage configuration combining all three units. 3 references.« less

Novel nanodispersed coal liquefaction catalysts: Molecular design via microemulsion-based synthesis. Final technical report, October 1990--December 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Osseo-Asare, K.; Boakye, E.; Vittal, M.

1995-04-01

This report described the synthesis of Molybdenum Sulfides in microemulsions by acidification of ammonium tetrathiomolybdate. Molybdenum Sulfides have been shown to be potential coal liquefaction catalysts. The importance of particle size, temperature effects, and coal surface chemistry to impregnation are discussed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chunshan Song; Hatcher, P.G.; Saini, A.K.

It has been indicated by DOE COLIRN panel that low-temperature catalytic pretreatment is a promising approach to the development of an improved liquefaction process. This work is a fundamental study on effects of pretreatments on coal structure and reactivity in liquefaction. The main objectives of this project are to study the coal structural changes induced by low-temperature catalytic and thermal pretreatments by using spectroscopic techniques; and to clarify the pretreatment-induced changes in reactivity or convertibility of coals. As the second volume of the final report, here we summarize our work on spectroscopic characterization of four raw coals including two subbituminousmore » coals and two bituminous coals, tetrahydrofuran (THF)-extracted but unreacted coals, the coals (THF-insoluble parts) that have been thermally pretreated. in the absence of any solvents and in the presence of either a hydrogen-donor solvent or a non-donor solvent, and the coals (THF-insoluble parts) that have been catalytically pretreated in the presence of a dispersed Mo sulfide catalyst in the absence of any solvents and in the presence of either a hydrogen-donor solvent or a non-donor solvent.« less

Hydrogen donor solvent coal liquefaction process

DOEpatents

Plumlee, Karl W.

1978-01-01

An indigenous hydrocarbon product stream boiling within a range of from about C.sub.1 -700.degree. F., preferably C.sub.1 -400.degree. F., is treated to produce an upgraded hydrocarbon fuel component and a component which can be recycled, with a suitable donor solvent, to a coal liquefaction zone to catalyze the reaction. In accordance therewith, a liquid hydrocarbon fraction with a high end boiling point range up to about 700.degree. F., preferably up to about 400.degree. F., is separated from a coal liquefaction zone effluent, the separated fraction is contacted with an alkaline medium to provide a hydrocarbon phase and an aqueous extract phase, the aqueous phase is neutralized, and contacted with a peroxygen compound to convert indigenous components of the aqueous phase of said hydrocarbon fraction into catalytic components, such that the aqueous stream is suitable for recycle to the coal liquefaction zone. Naturally occurring phenols and alkyl substituted phenols, found in the aqueous phase, are converted, by the addition of hydroxyl constituents to phenols, to dihydroxy benzenes which, as disclosed in copending Application Ser. Nos. 686,813 now U.S. Pat. No. 4,049,536; 686,814 now U.S. Pat. No. 4,049,537; 686,827 now U.S. Pat. No. 4,051,012 and 686,828, K. W. Plumlee et al, filed May 17, 1976, are suitable hydrogen transfer catalysts.

Meeting today's challenges to supply tomorrow's energy. Clean fossil energy technical and policy seminar

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

2005-07-01

Papers discussed the coal policy of China, Russia, Indonesia and Vietnam; clean coal technology (small-scale coal power plants, carbon capture and sequestration, new coking process SCOPE21, coal gasification (HyPr-RING), CO{sub 2} reduction technology, Supercritical coal-fired units and CFB boilers, EAGLE project, coal liquefaction), the coal consumer's view of clean fossil energy policy, and natural gas policy and technology. Some of the papers only consist of the presentation overheads/viewgraphs.

Advanced direct liquefaction concepts for PETC generic units. Quarterly technical progress report, October 1992--December 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The reactivity of the THF insoluble fraction of the ashy resid component of Wilsonville recycle oil (WRO) during liquefaction of Black Thunder coal in tetralin was determined at 415{degrees}C and 60 minutes. The liquefaction runs were made by combining this material with Black Thunder coal at the same ratio used in the WRO coal runs. THF conversion and product distribution from liquefaction in tetralin in the presence of the THF insoluble fraction of the ashy resid were similar to results from liquefaction in WRO. THF conversion was greater than loot with an oil yield that was somewhat higher than inmore » WRO. Differences in HC gas yield and H{sub 2} consumption were slight, while conversion and product distribution from liquefaction of Black Thunder coal in tetralin or in the WRO distillate were quite different. In both these solvents the 85--86% THF conversions were less than for runs in which the THF insoluble fraction of the ashy resid was present. This establishes that the THF insoluble fraction of the ashy resid is the reactive fraction of the WRO.« less

Rate of coal hydroliquefaction: correlation to coal structure. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baldwin, R.M.; Voorhees, K.J.; Durfee, S.L.

This report summarizes the research carried out on DOE grant No. FG22-83PC60784. The work was divided into two phases. The first phase consisted of a series of coal liquefaction rate measurements on seven different coals from the Exxon sample bank, followed by correlation with parent coal properties. The second phase involved characterization of the coals by pyrolysis/mass spectrometry and subsequent correlations of the Py/MS patterns with various liquefaction reactivity parameters. The hydroliquefaction reactivities for a suite of 7 bituminous and subbituminous coals were determined on a kinetic basis. These reactivities were correlated fairly successfully with the following parent coal properties:more » volatile matter, H/C and O/C ratios, vitrinite reflectance, and calorific value. The total surface areas of the coals were experimentally determined. Reactivity was shown to be independent of surface area. Following completion of the batch reactor experiments, the seven coals investigated were analyzed by pyrolysis/mass spectrometry. The pyrolysis spectra were then submitted to factor analysis in order to extract significant features of the coal for use in correlational efforts. These factors were then related to a variety of liquefaction reactivity definitions, including both rate and extent of liquefaction to solvent solubility classifications (oils, asphaltenes, preasphaltenes, etc.). In general, extent of reaction was found to correlate best with the Py/MS data. 37 refs., 25 figs., 11 tabs.« less

Direct liquefaction of plastics and coprocessing of coal with plastics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huffman, G.P.; Feng, Z.; Mahajan, V.

1995-12-31

The objectives of this work were to optimize reaction conditions for the direct liquefaction of waste plastics and the coprocessing of coal with waste plastics. In previous work, the direct liquefaction of medium and high density polyethylene (PE), polypropylene (PPE), poly(ethylene terephthalate) (PET), and a mixed plastic waste, and the coliquefaction of these plastics with coals of three different ranks was studied. The results established that a solid acid catalyst (HZSM-5 zeolite) was highly active for the liquefaction of the plastics alone, typically giving oil yields of 80-95% and total conversions of 90-100% at temperatures of 430-450 {degrees}C. In themore » coliquefaction experiments, 50:50 mixtures of plastic and coal were used with a tetralin solvent (tetralin:solid = 3:2). Using approximately 1% of the HZSM-5 catalyst and a nanoscale iron catalyst, oil yields of 50-70% and total conversion of 80-90% were typical. In the current year, further investigations were conducted of the liquefaction of PE, PPE, and a commingled waste plastic obtained from the American Plastics Council (APC), and the coprocessing of PE, PPE and the APC plastic with Black Thunder subbituminous coal. Several different catalysts were used in these studies.« less

Catalysts for coal liquefaction processes

DOEpatents

Garg, Diwakar

1986-01-01

Improved catalysts for catalytic solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a hydrogen donor solvent comprise a combination of zinc or copper, or a compound thereof, and a Group VI or non-ferrous Group VIII metal, or a compound thereof.

Catalysts for coal liquefaction processes

DOEpatents

Garg, D.

1986-10-14

Improved catalysts for catalytic solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a hydrogen donor solvent comprise a combination of zinc or copper, or a compound thereof, and a Group VI or non-ferrous Group VIII metal, or a compound thereof.

Studies of the effect of selected nondonor solvents on coal liquefaction yields

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jolley, R. L.; Rodgers, B. R.; Benjamin, B. M.

The objective of this research program was to evaluate the effectiveness of selected nondonor solvents (i.e., solvents that are not generally considered to have hydrogen available for hydrogenolysis reactions) for the solubilization of coals. Principal criteria for selection of candidate solvents were that the compound should be representative of a major chemical class, should be present in reasonable concentration in coal liquid products, and should have the potential to participate in hydrogen redistribution reactions. Naphthalene, phenanthrene, pyrene, carbazole, phenanthridine, quinoline, 1-naphthol, and diphenyl ether were evaluated to determine their effect on coal liquefaction yields and were compared with phenol andmore » two high-quality process solvents, Wilsonville SRC-I recycle solvent and Lummus ITSL heavy oil solvent. The high conversion efficacy of 1-naphthol may be attributed to its condensation to binaphthol and the consequent availability of hydrogen. The effectiveness of both the nitrogen heterocycles and the polycyclic aromatic hydrocarbon (PAH) compounds may be due to their polycyclic aromatic nature (i.e., possible hydrogen shuttling or transfer agents) and their physical solvent properties. The relative effectiveness for coal conversion of the Lummus ITSL heavy oil solvent as compared with the Wilsonville SRC-I process solvent may be attributed to the much higher concentration of 3-, 4-, and 5-ring PAH and hydroaromatic constituents in Lummus solvent. The chemistry of coal liquefaction and the development of recycle, hydrogen donor, and nondonor solvents are reviewed. The experimental methodology for tubing-bomb tests is outlined, and experimental problem areas are discussed.« less

Advanced Coal Liquefaction Research and Development Facility, Wilsonville, Alabama. Run 262 with Black Thunder subbituminous coal: Technical progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This report presents the results of Run 262 performed at the Advanced Coal Liquefaction R&D Facility in Wilsonville, Alabama. The run started on July 10, 1991 and continued until September 30, 1991, operating in the Close-Coupled Integrated Two-Stage Liquefaction mode processing Black Thunder Mine subbituminous coal (Wyodak-Anderson seam from Wyoming Powder River Basin). A dispersed molybdenum catalyst was evaluated for its performance. The effect of the dispersed catalyst on eliminating solids buildup was also evaluated. Half volume reactors were used with supported Criterion 324 1/16`` catalyst in the second stage at a catalyst replacement rate of 3 lb/ton of MFmore » coal. The hybrid dispersed plus supported catalyst system was tested for the effect of space velocity, second stage temperature, and molybdenum concentration. The supported catalyst was removed from the second stage for one test period to see the performance of slurry reactors. Iron oxide was used as slurry catalyst at a rate of 2 wt % MF coal throughout the run (dimethyl disulfide (DMDS) was used as the sulfiding agent). The close-coupled reactor unit was on-stream for 1271.2 hours for an on-stream factor of 89.8% and the ROSE-SR unit was on-feed for 1101.6 hours for an on-stream factor of 90.3% for the entire run.« less

Coal liquefaction processes and development requirements analysis for synthetic fuels production

NASA Technical Reports Server (NTRS)

1980-01-01

Focus of the study is on: (1) developing a technical and programmatic data base on direct and indirect liquefaction processes which have potential for commercialization during the 1980's and beyond, and (2) performing analyses to assess technology readiness and development trends, development requirements, commercial plant costs, and projected synthetic fuel costs. Numerous data sources and references were used as the basis for the analysis results and information presented.

Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 3: Combustors, furnaces and low-BTU gasifiers. [used in coal gasification and coal liquefaction (equipment specifications)

NASA Technical Reports Server (NTRS)

Hamm, J. R.

1976-01-01

Information is presented on the design, performance, operating characteristics, cost, and development status of coal preparation equipment, combustion equipment, furnaces, low-Btu gasification processes, low-temperature carbonization processes, desulfurization processes, and pollution particulate removal equipment. The information was compiled for use by the various cycle concept leaders in determining the performance, capital costs, energy costs, and natural resource requirements of each of their system configurations.

Surfactant-assisted liquefaction of particulate carbonaceous substances

NASA Technical Reports Server (NTRS)

Hsu, G. C. (Inventor)

1978-01-01

A slurry of carbonaceous particles such as coal containing an oil soluble polar substituted oleophilic surfactant, suitably an amine substituted long chain hydrocarbon, is liquefied at high temperature and high hydrogen presence. The pressure of surfactant results in an increase in yield and the conversion product contains a higher proportion of light and heavy oils and less asphaltene than products from other liquefaction processes.

Catalytic two-stage coal hydrogenation process using extinction recycle of heavy liquid fraction

DOEpatents

MacArthur, J.B.; Comolli, A.G.; McLean, J.B.

1989-10-17

A process is described for catalytic two-stage hydrogenation and liquefaction of coal with selective extinction recycle of all heavy liquid fractions boiling above a distillation cut point of about 600--750 F to produce increased yields of low-boiling hydrocarbon liquid and gas products. In the process, the particulate coal feed is slurried with a process-derived liquid solvent normally boiling above about 650 F and fed into a first stage catalytic reaction zone operated at conditions which promote controlled rate liquefaction of the coal, while simultaneously hydrogenating the hydrocarbon recycle oils. The first stage reactor is maintained at 710--800 F temperature, 1,000--4,000 psig hydrogen partial pressure, and 10-90 lb/hr per ft[sup 3] catalyst space velocity. Partially hydrogenated material withdrawn from the first stage reaction zone is passed directly to the second stage catalytic reaction zone maintained at 760--860 F temperature for further hydrogenation and hydroconversion reactions. A 600--750 F[sup +] fraction containing 0--20 W % unreacted coal and ash solids is recycled to the coal slurrying step. If desired, the cut point lower boiling fraction can be further catalytically hydrotreated. By this process, the coal feed is successively catalytically hydrogenated and hydroconverted at selected conditions, to provide significantly increased yields of desirable low-boiling hydrocarbon liquid products and minimal production of hydrocarbon gases, and no net production of undesirable heavy oils and residuum materials. 2 figs.

Catalytic two-stage coal hydrogenation process using extinction recycle of heavy liquid fraction

DOEpatents

MacArthur, James B.; Comolli, Alfred G.; McLean, Joseph B.

1989-01-01

A process for catalytic two-stage hydrogenation and liquefaction of coal with selective extinction recycle of all heavy liquid fractions boiling above a distillation cut point of about 600.degree.-750.degree. F. to produce increased yields of low-boiling hydrocarbon liquid and gas products. In the process, the particulate coal feed is slurried with a process-derived liquid solvent normally boiling above about 650.degree. F. and fed into a first stage catalytic reaction zone operated at conditions which promote controlled rate liquefaction of the coal, while simultaneously hydrogenating the hydrocarbon recycle oils. The first stage reactor is maintained at 710.degree.-800.degree. F. temperature, 1000-4000 psig hydrogen partial pressure, and 10-90 lb/hr per ft.sup.3 catalyst space velocity. Partially hydrogenated material withdrawn from the first stage reaction zone is passed directly to the second stage catalytic reaction zone maintained at 760.degree.-860.degree. F. temperature for further hydrogenation and hydroconversion reactions. A 600.degree.-750.degree. F..sup.+ fraction containing 0-20 W % unreacted coal and ash solids is recycled to the coal slurrying step. If desired, the cut point lower boiling fraction can be further catalytically hydrotreated. By this process, the coal feed is successively catalytically hydrogenated and hydroconverted at selected conditions, to provide significantly increased yields of desirable low-boiling hydrocarbon liquid products and minimal production of hydrocarbon gases, and no net production of undesirable heavy oils and residuum materials.

Analysis and comparison of inertinite-derived adsorbent with conventional adsorbents.

PubMed

Gangupomu, Roja Haritha; Kositkanawuth, Ketwalee; Sattler, Melanie L; Ramirez, David; Dennis, Brian H; MacDonnell, Frederick M; Billo, Richard; Priest, John W

2012-05-01

To increase U.S. petroleum energy-independence, the University of Texas at Arlington (UT Arlington) has developed a coal liquefaction process that uses a hydrogenated solvent and a proprietary catalyst to convert lignite coal to crude oil. This paper reports on part of the environmental evaluation of the liquefaction process: the evaluation of the solid residual from liquefying the coal, called inertinite, as a potential adsorbent for air and water purification. Inertinite samples derived from Arkansas and Texas lignite coals were used as test samples. In the activated carbon creation process, inertinite samples were heated in a tube furnace (Lindberg, Type 55035, Arlington, UT) at temperatures ranging between 300 and 850 degrees C for time spans of 60, 90, and 120 min, using steam and carbon dioxide as oxidizing gases. Activated inertinite samples were then characterized by ultra-high-purity nitrogen adsorption isotherms at 77 K using a high-speed surface area and pore size analyzer (Quantachrome, Nova 2200e, Kingsville, TX). Surface area and total pore volume were determined using the Brunauer Emmet, and Teller method, for the inertinite samples, as well as for four commercially available activated carbons (gas-phase adsorbents Calgon Fluepac-B and BPL 4 x 6; liquid-phase adsorbents Filtrasorb 200 and Carbsorb 30). In addition, adsorption isotherms were developed for inertinite and the two commercially available gas-phase carbons, using methyl ethyl ketone (MEK) as an example compound. Adsorption capacity was measured gravimetrically with a symmetric vapor sorption analyzer (VTI, Inc., Model SGA-100, Kingsville, TX). Also, liquid-phase adsorption experiments were conducted using methyl orange as an example organic compound. The study showed that using inertinite from coal can be beneficially reused as an adsorbent for air or water pollution control, although its surface area and adsorption capacity are not as high as those for commercially available activated carbons. The United States currently imports two-thirds of its crude oil, leaving its transportation system especially vulnerable to disruptions in international crude supplies. UT Arlington has developed a liquefaction process that converts coal, abundant in the United States, to crude oil. This work demonstrated that the undissolvable solid coal residual from the liquefaction process, called inertinite, can be converted to an activated carbon adsorbent. Although its surface area and adsorption capacity are not as high as those for commercially available carbons, the inertinite source material would be available at no cost, and its beneficial reuse would avoid the need for disposal.

Fossil energy program

NASA Astrophysics Data System (ADS)

McNeese, L. E.

1981-12-01

The progress made during the period from July 1 through September 30 for the Oak Ridge National Laboratory research and development projects in support of the increased utilization of coal and other fossil fuels as sources of clean energy is reported. The following topics are discussed: coal conversion development, chemical research and development, materials technology, fossil energy materials program, liquefaction projects, component development, process analysis, environmental control technology, atmospheric fluidized bed combustion, underground coal gasification, coal preparation and waste utilization.

Liquefaction process

DOEpatents

Gorbaty, Martin L.; Stone, John B.; Poddar, Syamal K.

1982-01-01

Scale formation during the liquefaction of lower ranking coals and similar carbonaceous materials is significantly reduced and/or prevented by pretreatment with a combination of pretreating agents comprising SO.sub.2 and an oxidizing agent. The pretreatment is believed to convert at least a portion of the scale-forming components and particularly calcium, to the corresponding sulfate prior to liquefaction. The pretreatment may be accomplished with the combination of pretreating agents either simultaneously by using a mixture comprising SO.sub.2 and an oxidizing agent or sequentially by first treating with SO.sub.2 and then with an oxidizing agent.

Effects of low-temperature catalytic pretreatments on coal structure and reactivity in liquefaction. Final technical report, Volume 1 - effects of solvents, catalysts and temperature conditions on conversion and structural changes of low-rank coals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Lili; Schobert, Harold H.; Song, Chunshan

1998-01-01

The main objectives of this project were to study the effects of low-temperature pretreatments on coal structure and their impacts on subsequent liquefaction. The effects of pretreatment temperatures, catalyst type, coal rank, and influence of solvent were examined. Specific objectives were to identify the basic changes in coal structure induced by catalytic and thermal pretreatments, and to determine the reactivity of the catalytically and thermally treated coals for liquefaction. In the original project management plan it was indicated that six coals would be used for the study. These were to include two each of bituminous, subbituminous, and lignite rank. Formore » convenience in executing the experimental work, two parallel efforts were conducted. The first involved the two lignites and one subbituminous coal; and the second, the two bituminous coals and the remaining subbituminous coal. This Volume presents the results of the first portion of the work, studies on two lignites and one subbituminous coal. The remaining work accomplished under this project will be described and discussed in Volume 2 of this report. The objective of this portion of the project was to determine and compare the effects of solvents, catalysts and reaction conditions on coal liquefaction. Specifically, the improvements of reaction conversion, product distribution, as well as the structural changes in the coals and coal-derived products were examined. This study targeted at promoting hydrogenation of the coal-derived radicals, generated during thermal cleavage of chemical bonds, by using a good hydrogen donor-solvent and an effective catalyst. Attempts were also made in efforts to match the formation and hydrogenation of the free radicals and thus to prevent retrogressive reaction.« less

Quarterly technical progress report, April-June 1982

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1984-04-01

Progress reports are presented for the following tasks: (1) preparation of low-rank coals; application of liquefaction processes to low-rank coals; (2) slagging fixed-bed gasification; (3) atmospheric fluidized-bed combustion of low-rank coal; (4) ash fouling and combustion modification for low-rank coal; (5) combined flue gas cleanup/simultaneous SO/sub x/-NO/sub x/ control; (6) particulate control and hydrocarbons and trace element emissions from low-rank coals; (7) waste characterization and disposal; and (9) exploratory research.

Automated apparatus for solvent separation of a coal liquefaction product stream

DOEpatents

Schweighardt, Frank K.

1985-01-01

An automated apparatus for the solvent separation of a coal liquefaction product stream that operates continuously and unattended and eliminates potential errors resulting from subjectivity and the aging of the sample during analysis. In use of the apparatus, metered amounts of one or more solvents are passed sequentially through a filter containing the sample under the direction of a microprocessor control means. The mixture in the filter is agitated by means of ultrasonic cavitation for a timed period and the filtrate is collected. The filtrate of each solvent extraction is collected individually and the residue on the filter element is collected to complete the extraction process.

Advanced direct coal liquefaction concepts. Quarterly report, April 1, 1993--June 30, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berger, D.J.; Parker, R.J.; Simpson, P.L.

Construction and commissioning of the bench unit for operation of the first stage of the process was completed. Solubilization of Black Thunder coal using carbon monoxide and steam was successfully demonstrated in the counterflow reactor system. The results were comparable with those obtained in the autoclave with the exception that coal solubilization at the same nominal residence times was slightly lower. The bench unit has now been modified for two stage operation. The Wilsonville process derived solvent for Black Thunder coal (V-1074) was found to be essentially as stable as the previous solvent used in the autoclave runs (V-178 +more » 320) at reactor conditions. This solvent (V-1074) is, therefore, being used in the bench unit tests. Carbon monoxide may be replaced by synthesis gas for the coal solubilization step in the process. However, in autoclave tests, coal conversion was found to be dependent on the amount of carbon monoxide present in the synthesis gas. Coal conversions ranged from 88% for pure carbon monoxide to 67% for a 25:75 carbon monoxide/hydrogen mixture at equivalent conditions. Two stage liquefaction tests were completed in the autoclave using a disposable catalyst (FeS) and hydrogen in the second stage. Increased coal conversion, higher gas and oil and lower asphaltene and preasphaltene yields were observed as expected. However, no hydrogen consumption was observed in the second stage. Other conditions, in particular, alternate catalyst systems will be explored.« less

High conversion of coal to transportation fuels for the future with low HC gas production. Progress report Number 10, January 1--March 31, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiser, W.H.; Oblad, A.G.

1995-04-01

An objective of the Department of Energy in funding research in coal liquefaction, is to produce a synthetic crude from coal at a cost lower than $30.00 per barrel (Task A). A second objective is to produce a fuel which is low in aromatics, yet of sufficiently high octane number for use in the gasoline-burning transportation vehicles of today. To meet this second objective, research was proposed for conversion of the highly-aromatic liquid product from coal conversion to a product high in isoparaffins, which compounds in the gasoline range exhibit a high octane number (Task B). Experimental coal liquefaction studiesmore » conducted in a batch microreactor have demonstrated potential for high conversions of coal to liquids with low yields of hydrocarbon (HC) gases, hence small consumption of hydrogen in the primary liquefaction step. Ratios of liquids/HC gases as high as 30/1, at liquid yields as high as 82% of the coal by weight, have been achieved. The principal objective of this work is to examine how nearly one may approach these results in a continuous-flow system, at a size sufficient to evaluate the process concept for production of transportation fuels from coal. A continuous-flow reactor system is to be designed, constructed and operated. The system is to be computer-operated for process control and data logging, and is to be fully instrumented. The primary liquid products will be characterized by GC, FTIR, and GC/MS, to determine the types and quantities of the principal components produced under conditions of high liquids production with high ratios of liquids/HC gases. From these analyses, together with GC analyses of the HC gases, hydrogen consumption for the conversion to primary liquids will be calculated. Conversion of the aromatics of this liquid product to isoparaffins will be investigated. Results to date on both tasks are presented.« less

Novel use of residue from direct coal liquefaction process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jianli Yang; Zhaixia Wang; Zhenyu Liu

2009-09-15

Direct coal liquefaction residue (DCLR) is, commonly, designed to be used as a feed stock for gasification or combustion. Use of DCLR as a value added product is very important for improving overall economy of direct coal liquefaction processes. This study shows that the DCLR may be used as a pavement asphalt modifier. The modification ability is similar to that of Trinidad Lake Asphalt (TLA), a superior commercial modifier. Asphalts modified by two DCLRs meet the specifications of ASTM D5710 and BSI BS-3690 designated for the TLA-modified asphalts. The required addition amount for the DCLRs tested is less than thatmore » for TLA due possibly to the high content of asphaltene in DCLRs. Different compatibility was observed for the asphalts with the same penetration grade but from the different origin. Different components in the DCLR play different roles in the modification. Positive synergetic effects among the fractions were observed, which may due to the formation of the stable colloid structure. Unlike polymer-type modifier, the structure of asphalt-type modifier has a similarity with petroleum asphalts which favors the formation of a stable dispersed polar fluid (DPF) colloid structure and improves the performance of pavement asphalt. 12 refs., 1 fig., 6 tabs.« less

Coal liquefaction process with increased naphtha yields

DOEpatents

Ryan, Daniel F.

1986-01-01

An improved process for liquefying solid carbonaceous materials wherein the solid carbonaceous material is slurried with a suitable solvent and then subjected to liquefaction at elevated temperature and pressure to produce a normally gaseous product, a normally liquid product and a normally solid product. The normally liquid product is further separated into a naphtha boiling range product, a solvent boiling range product and a vacuum gas-oil boiling range product. At least a portion of the solvent boiling-range product and the vacuum gas-oil boiling range product are then combined and passed to a hydrotreater where the mixture is hydrotreated at relatively severe hydrotreating conditions and the liquid product from the hydrotreater then passed to a catalytic cracker. In the catalytic cracker, the hydrotreater effluent is converted partially to a naphtha boiling range product and to a solvent boiling range product. The naphtha boiling range product is added to the naphtha boiling range product from coal liquefaction to thereby significantly increase the production of naphtha boiling range materials. At least a portion of the solvent boiling range product, on the other hand, is separately hydrogenated and used as solvent for the liquefaction. Use of this material as at least a portion of the solvent significantly reduces the amount of saturated materials in said solvent.

Fossil Energy Program

NASA Astrophysics Data System (ADS)

McNeese, L. E.

1981-01-01

Increased utilization of coal and other fossil fuel alternatives as sources of clean energy is reported. The following topics are discussed: coal conversion development, chemical research and development, materials technology, component development and process evaluation studies, technical support to major liquefaction projects, process analysis and engineering evaluations, fossil energy environmental analysis, flue gas desulfurization, solid waste disposal, coal preparation waste utilization, plant control development, atmospheric fluidized bed coal combustor for cogeneration, TVA FBC demonstration plant program technical support, PFBC systems analysis, fossil fuel applications assessments, performance assurance system support for fossil energy projects, international energy technology assessment, and general equilibrium models of liquid and gaseous fuel supplies.

Integrated process for the solvent refining of coal

DOEpatents

Garg, Diwakar

1983-01-01

A process is set forth for the integrated liquefaction of coal by the catalytic solvent refining of a feed coal in a first stage to liquid and solid products and the catalytic hydrogenation of the solid product in a second stage to produce additional liquid product. A fresh inexpensive, throw-away catalyst is utilized in the second stage hydrogenation of the solid product and this catalyst is recovered and recycled for catalyst duty in the solvent refining stage without any activation steps performed on the used catalyst prior to its use in the solvent refining of feed coal.

Undergraduate research studies program at participating institutions of the HBCU Fossil Energy Consortium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhatia, S.C.; Cardelino, B.H.; Hall, J.H. Jr.

1990-01-31

This report consists of five quarterly progress reports from four participating universities. The titles of the projects are: Competition of NO and SO{sub 2} for OH generated within electrical aerosol analyzers; Dispersed iron catalysts for coal gasification; Catalytic gasification of coal chars by potassium sulfate and ferrous sulfate mixtures; Removal of certain toxic heavy metal ions in coal conversion process wastewaters; and Study of coal liquefaction catalysts. All reports have been indexed separately for inclusion on the data base. (CK)

Liquefaction of solid carbonaceous material with catalyst recycle

DOEpatents

Gupta, Avinash; Greene, Marvin I.

1992-01-01

In the two stage liquefaction of a carbonaceous solid such as coal wherein coal is liquefied in a first stage in the presence of a liquefaction solvent and the first stage effluent is hydrogenated in the presence of a supported hydrogenation catalyst in a second stage, catalyst which has been previously employed in the second stage and comminuted to a particle size distribution equivalent to 100% passing through U.S. 100 Mesh, is passed to the first stage to improve the overall operation.

Highly dispersed catalysts for coal liquefaction. Quarterly report No. 9, August 23, 1993--November 22, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirschon, A.S.; Wilson, R.B.

We analyzed two sets of liquefaction experiments, one involved the liquefaction of Black Thunder Coal with the corresponding recycle vehicle, and the second set of liquefaction runs involved the liquefaction of Argonne North Dakota Lignite. We compared coal conversions of Black Thunder coal and recycle solvent using Fe(CO){sub 5} and carbon monoxide/hydrogen atmospheres and a MolyVanL molybdenum catalyst under a hydrogen atmosphere. We also continued our investigation of the effect of water on the conversions. We found that addition of water seemed to decrease the amount of oils; we determined the effect of water with the recycle solvent alone, (nomore » coal added) under similar conditions, and again produced a decrease in oil yields. FIMS analyses of the hexane and toluene soluble fractions seem to indicate that in the experiment when water was added, a considerable amount of light material remained behind in the toluene layer, suggesting that somehow the addition of water decreased the amount of extracted material, perhaps by increasing the amount of polarity of the product. When the conversion was conducted with the MolyVanL molybdenum catalyst a good quality product in terms of lower viscosity was produced; however, conversions to THF soluble material was not increased. We believe the molybdenum catalyst hydrogenated the recycle vehicle rather than effectively converted the coal. In order to eliminate the effect of solvent we have often conducted experiments in an inert solvent with Argonne coals. We conducted several coal conversions experiments using an Argonne North Dakota lignite. We compared several dispersed Fe catalysts and in addition, a nickel catalyst. We investigated nickel as a catalyst since we believe this metal may be more effective in decarboxylating low rank coals. Consistent with this premise we found that the nickel catalyst gave the highest conversions.« less

30 CFR 206.264 - In-situ and surface gasification and liquefaction operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false In-situ and surface gasification and... THE INTERIOR MINERALS REVENUE MANAGEMENT PRODUCT VALUATION Federal Coal § 206.264 In-situ and surface gasification and liquefaction operations. If an ad valorem Federal coal lease is developed by in-situ or...

30 CFR 1206.463 - In-situ and surface gasification and liquefaction operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false In-situ and surface gasification and..., DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.463 In-situ and surface gasification and liquefaction operations. If an ad valorem Federal coal lease is developed by in...

30 CFR 1206.463 - In-situ and surface gasification and liquefaction operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false In-situ and surface gasification and..., DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.463 In-situ and surface gasification and liquefaction operations. If an ad valorem Federal coal lease is developed by in...

30 CFR 1206.264 - In-situ and surface gasification and liquefaction operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false In-situ and surface gasification and..., DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.264 In-situ and surface gasification and liquefaction operations. If an ad valorem Federal coal lease is developed by in...

30 CFR 206.463 - In-situ and surface gasification and liquefaction operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false In-situ and surface gasification and... THE INTERIOR MINERALS REVENUE MANAGEMENT PRODUCT VALUATION Indian Coal § 206.463 In-situ and surface gasification and liquefaction operations. If an ad valorem Federal coal lease is developed by in-situ or...

30 CFR 1206.264 - In-situ and surface gasification and liquefaction operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false In-situ and surface gasification and..., DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.264 In-situ and surface gasification and liquefaction operations. If an ad valorem Federal coal lease is developed by in...

30 CFR 1206.463 - In-situ and surface gasification and liquefaction operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false In-situ and surface gasification and..., DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.463 In-situ and surface gasification and liquefaction operations. If an ad valorem Federal coal lease is developed by in...

30 CFR 1206.264 - In-situ and surface gasification and liquefaction operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false In-situ and surface gasification and..., DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.264 In-situ and surface gasification and liquefaction operations. If an ad valorem Federal coal lease is developed by in...

Production and Optimization of Direct Coal Liquefaction derived Low Carbon-Footprint Transportation Fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steven Markovich

This report summarizes works conducted under DOE Contract No. DE-FC26-05NT42448. The work scope was divided into two categories - (a) experimental program to pretreat and refine a coal derived syncrude sample to meet transportation fuels requirements; (b) system analysis of a commercial scale direct coal liquefaction facility. The coal syncrude was derived from a bituminous coal by Headwaters CTL, while the refining study was carried out under a subcontract to Axens North America. The system analysis included H{sub 2} production cost via six different options, conceptual process design, utilities requirements, CO{sub 2} emission and overall plant economy. As part ofmore » the system analysis, impact of various H{sub 2} production options was evaluated. For consistence the comparison was carried out using the DOE H2A model. However, assumptions in the model were updated using Headwaters database. Results of Tier 2 jet fuel specifications evaluation by the Fuels & Energy Branch, US Air Force Research Laboratory (AFRL/RZPF) located at Wright Patterson Air Force Base (Ohio) are also discussed in this report.« less

Removing micron size particles from coal liquids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodgers, B.R.; Westmoreland, P.R.

This paper reports results of an investigation which was undertaken in order to improve purification of liquid fuels obtained by coal liquefaction processes. It is shown that settling and filtration rates increased substantially after agglomeration. And, ground coal was found to be an economical substitute for diatomaceous earth in filtration. The effects of certain solvents on the agglomerating tendencies of solids in the unfiltered oil (UFO) from the SRC and COED processes were determined by oil immersion microscopy. The significant results obtained by these experiments are listed. Economic advantages are presented. 13 references.

Testing of advanced liquefaction concepts in HTI Run ALC-1: Coal cleaning and recycle solvent treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robbins, G.A.; Winschel, R.A.; Burke, F.P.

In 1991, the Department of Energy initiated the Advanced Liquefaction Concepts Program to promote the development of new and emerging technology that has potential to reduce the cost of producing liquid fuels by direct coal liquefaction. Laboratory research performed by researchers at CAER, CONSOL, Sandia, and LDP Associates in Phase I is being developed further and tested at the bench scale at HTI. HTI Run ALC-1, conducted in the spring of 1996, was the first of four planned tests. In Run ALC-1, feed coal ash reduction (coal cleaning) by oil agglomeration, and recycle solvent quality improvement through dewaxing and hydrotreatmentmore » of the recycle distillate were evaluated. HTI`s bench liquefaction Run ALC-1 consisted of 25 days of operation. Major accomplishments were: 1) oil agglomeration reduced the ash content of Black Thunder Mine coal by 40%, from 5.5% to 3.3%; 2) excellent coal conversion of 98% was obtained with oil agglomerated coal, about 3% higher than the raw Black Thunder Mine coal, increasing the potential product yield by 2-3% on an MAF coal basis; 3) agglomerates were liquefied with no handling problems; 4) fresh catalyst make-up rate was decreased by 30%, with no apparent detrimental operating characteristics, both when agglomerates were fed and when raw coal was fed (with solvent dewaxing and hydrotreating); 5) recycle solvent treatment by dewaxing and hydrotreating was demonstrated, but steady-state operation was not achieved; and 6) there was some success in achieving extinction recycle of the heaviest liquid products. Performance data have not been finalized; they will be available for full evaluation in the new future.« less

Process for coal liquefaction using electrodeposited catalyst

DOEpatents

Moore, Raymond H.

1978-01-01

A process for the liquefaction of solid hydrocarbonaceous materials is disclosed. Particles of such materials are electroplated with a metal catalyst and are then suspended in a hydrocarbon oil and subjected to hydrogenolysis to liquefy the solid hydrocarbonaceous material. A liquid product oil is separated from residue solid material containing char and the catalyst metal. The catalyst is recovered from the solid material by electrolysis for reuse. A portion of the product oil can be employed as the hydrocarbon oil for suspending additional particles of catalyst coated solid carbonaceous material for hydrogenolysis.

Air impacts from three alternatives for producing JP-8 jet fuel.

PubMed

Kositkanawuth, Ketwalee; Gangupomu, Roja Haritha; Sattler, Melanie L; Dennis, Brian H; MacDonnell, Frederick M; Billo, Richard; Priest, John W

2012-10-01

To increase U.S. petroleum energy independence, the University of Texas at Arlington (UT Arlington) has developed a direct coal liquefaction process which uses a hydrogenated solvent and a proprietary catalyst to convert lignite coal to crude oil. This sweet crude can be refined to form JP-8 military jet fuel, as well as other end products like gasoline and diesel. This paper presents an analysis of air pollutants resulting from using UT Arlington's liquefaction process to produce crude and then JP-8, compared with 2 alternative processes: conventional crude extraction and refining (CCER), and the Fischer-Tropsch process. For each of the 3 processes, air pollutant emissions through production of JP-8 fuel were considered, including emissions from upstream extraction/ production, transportation, and conversion/refining. Air pollutants from the direct liquefaction process were measured using a LandTEC GEM2000 Plus, Draeger color detector tubes, OhioLumex RA-915 Light Hg Analyzer, and SRI 8610 gas chromatograph with thermal conductivity detector. According to the screening analysis presented here, producing jet fuel from UT Arlington crude results in lower levels of pollutants compared to international conventional crude extraction/refining. Compared to US domestic CCER, the UTA process emits lower levels of CO2-e, NO(x), and Hg, and higher levels of CO and SO2. Emissions from the UT Arlington process for producing JP-8 are estimated to be lower than for the Fischer-Tropsch process for all pollutants, with the exception of CO2-e, which were high for the UT Arlington process due to nitrous oxide emissions from crude refining. When comparing emissions from conventional lignite combustion to produce electricity, versus UT Arlington coal liquefaction to make JP-8 and subsequent JP-8 transport, emissions from the UT Arlington process are estimated to be lower for all air pollutants, per MJ of power delivered to the end user. The United States currently imports two-thirds of its crude oil, leaving its transportation system especially vulnerable to disruptions in international crude supplies. At current use rates, U.S. coal reserves (262 billion short tons, including 23 billion short tons lignite) would last 236 years. Accordingly, the University of Texas at Arlington (UT Arlington) has developed a process that converts lignite to crude oil, at about half the cost of regular crude. According to the screening analysis presented here, producing jet fuel from UT Arlington crude generates lower levels of pollutants compared to international conventional crude extraction/refining (CCER).

Concept of a self-associated multimer structure of coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gagarin, S.G.; Krichko, A.A.

1984-01-01

The paper examines the role of donor-acceptor reaction in the binding of the individual components forming the structure of the organic coal mass, and analyses the manifestations of this reaction during liquefaction. The authors put forward the concept of self-associated polymers in the coal structure, in accordance with which the organic coal mass has spatial and energetic distribution of the donor and acceptor sectors of structure. It is the specific reaction between these which produces the necessary stability to the polymer system under normal conditions. The authors propose a mechanism for the action of solvents and various additives in themore » liquefaction of coal.« less

Synthesis and reactivity of ultra-fine coal liquefaction catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Linehan, J.C.; Matson, D.W.; Fulton, J.L.

1992-10-01

The Pacific Northwest Laboratory is currently developing ultra-fine iron-based coal liquefaction catalysts using two new particle production technologies: (1) modified reverse micelles (MRM) and (2) rapid thermal decomposition of solutes (RTDS). These methodologies have been shown to allow control over both particle size (from 1 nm to 60 nm) and composition when used to produce ultra-fine iron-based materials. Powders produced using these methods are found to be selective catalysts for carbon-carbon bond scission using the naphthyl bibenzylmethane model compound, and to promote the production of THF soluble coal products during liquefaction studies. This report describes the materials produced by bothmore » MRM and the RTDS methods and summarizes the results of preliminary catalysis studies using these materials.« less

Advanced direct coal liquefaction concepts. Quarterly report, July 1--September 30, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berger, D.J.; Parker, R.J.; Simpson, P.L.

All the reports required for completion of the contract were submitted this quarter. A proposal for further work in Phase 2 was also submitted. The technical and economic assessment of the process was completed. The results show that for the base case scenario (25% equity, 15% after tax DCF-ROE) coal derived synthetic crude oil can be produced at just below US $30 per barrel. The study was based on the production of 75,000 BPD of C{sub 4+} synthetic crude oil from Black Thunder coal for subsequent processing in a conventional petroleum refinery from Black Thunder (Wyoming) subbituminous coal.

Superacid Catalyzed Depolymerization and Conversion of Coals. Final Technical Report. [HF:BF{sub 2}/H{sub 2}

DOE R&D Accomplishments Database

Olah, G.

1980-01-01

We were interested in applying superacid catalyzed cleavage-depolymerization and ionic hydrogenation low temperature conversion of coal to liquid hydrocarbon, as well as obtaining information about the reactions involved and the structure of intermediates of the coal liquefaction process. In order to show the feasibility of our proposed research we have carried out preliminary investigation in these areas. Preceding our work there was no practical application of a superacid system to coal liquefaction. We carried out an extensive study of the potential of the HF:BF{sub 3}/H{sub 2} system for coal hydroliquefaction. Under varying conditions of reactant ratio, reaction time and temperature, we were able to obtain over 95% pyridine extractible product by treating coal in HF:BF{sub 3}:H{sub 2} system at approx. 100 degrees C for 4 hours. The coal to acid ratio was 1:5 and FB{sub 3} at 900 psi and H{sub 2} at 500 psi were used. These are extremely encouraging results in that the conditions used are drastically milder than those used in any known process, such as Exxon donor solvent and related processes. The cyclohexane extractibility of the treated coal was as high as 27% and the yield of liquid distillate at 400 degrees C/5 x 10{sup -3}/sup torr/ was approx. 30%. The infrared spectrum of product coal, extracts and distillates were distinctly different from the starting coal and show a significant increase in the amount of saturates. The {sup 1}H NMR spectrum of cyclohexane extract of the treated coal shows essentially all aliphatic photons. The spectra of other treated coal extracts show increased amounts and types of aliphatic protons as well as significant amounts of protons bound to unsaturated sites. This again indicates that the HF-BF{sub 3} system is depolymerizing the coal to small fragments which are soluble in non-polar solvents.

Pillared montmorillonite catalysts for coal liquefaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, R.K.; Olson, E.S.

1994-12-31

Pillared clays contain large micropores and have considerable potential for catalytic hydrogenation and cleavage of coal macromolecules. Pillared montmorillonite-supported catalysts were prepared by the intercalation of polynuclear hydroxychromium cations and subsequent impregnation of nickel and molybdenum. Infrared and thermogravimetric studies of pyridine-adsorbed catalysts indicated the presence of both Lewis and Bronsted acid sites. Thus, the catalysts have both acidic properties that can aid in hydrocracking and cleavage of carbon-heteroatom bonds as well as hydrogen-activating bimetallic sites. These catalysts were applied to the hydrodesulfurization and liquefaction of coal-derived intermediates. The reactions of model organosulfur compounds and coal liquids were carried outmore » at 300{degrees}-400{degrees}C for 3 hours in the presence of 1000 psi of molecular hydrogen. Reaction products were analyzed by GC/FT-IR/MS/AED. The catalysts have been found to be very effective in removing sulfur from model compounds as well as liquefaction products.« less

Reactivity of coal in direct hydrogenation processes: Technical progress report, March-May 1987

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baldwin, R.M.; Miller, R.L.

Research during the past quarter centered on continuation of two facets related to the study of coal reactivity in direct hydrogenation liquefaction processes. Five coals from the Argonne Premium coal collection were liquefied at three temperature levels in order to gather data for kinetic analysis purposes. Conversion of these coals to THF-, toluene-, and hexane-solubles was determined at temperatures of 425, 400, and 375 C, and nominal reaction times of 3, 5, 10, 15, and 40 minutes in the microautoclave batch reaction system. Preliminary mathematical modeling of the data using simple irreversible rate expressions and more complex formulations based onmore » a statistical distribution of activation energies was initiated in order to investigate the feasibility of utilizing activation energy as an additional reactivity screening factor. Use of complex models such as the Anthony-Howard formulation for purposes of activation energy determination from liquefaction data at one temperature level was further examined. Five of the 21 coals from the Penn State Premium coal sample bank were liquefied at the standard reactivity screening conditions, and the rate and extent of conversion to THF-, and toluene-, and hexane-solubles quantified. These data were added to the existing data base containing similar information for the prior coal suites from the Exxon and Argonne collections, and preliminary correlational efforts for reactivity vs. coal properties were initiated. Prior conclusions regarding the effect of rank on the rate and extent of conversion were qualitatively verified from the data collected. 1 ref., 13 figs., 2 tabs.« less

DIRECT LIQUEFACTION PROOF OF CONCEPT

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The eighth bench scale test of POC program, Run PB-08, was successfully completed from August 8 to August 26, 1997. A total of five operating conditions were tested aiming at evaluating the reactivity of different pyrolysis oils in liquefaction of a Wyoming sub-bituminous coal (Black Thunder coal). For the first time, water soluble promoters were incorporated into the iron-based GelCat to improve the dispersion of the promoter metals in the feed blend. The concentration of the active metals, Mo and Fe, was 100 and 1000 ppm of moisture-free coal, respectively. Black Thunder coal used in this run was the samemore » batch as tested in HTI�s Run POC-02. Similar to Runs PB-01 through 7, this run employed two back mixed slurry reactors, an interstage gas/slurry separator and a direct-coupled hydrotreater. In addition to the hot vapor from the second stage separator, the first stage separator overhead liquid was also fed to the hydrotreater, which was packed with Criterion C-411 hydrotreating catalyst. Pyrolysis oil was produced off-line from a pyrolysis unit acquired from University of Wyoming. Solids rejection was achieved by purging out pressure filter solid. The recycle solvents consisted of O-6 separator bottoms and pressure filter liquid (PFL). The Run PB-08 proceeded very smoothly without any interruptions. Coal conversion consistently above 90W% was achieved. High resid conversion and distillate yield have been obtained from co-processing of coal and 343°C+ (650°F+) pyrolysis oil. Light gas (C 1-C 3 ) yield was minimized and hydrogen consumption was reduced due to the introduction of pyrolysis oil, compared with conventional coal-derived solvent. Catalytic activity was improved by incorporating a promoter metal into the iron-based GelCat. It seemed that lowering the first stage temperature to 435°C might increase the hydrogenation function of the promoter metal. In comparison with previous coal-waste coprocessing run (PB-06), significant improvements in the process performance were achieved due to catalyst modification and integration of pyrolysis technique into liquefaction.« less

Direct liquefaction Proof-of-Concept facility. Final technical progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Comolli, A.G.; Lee, L.K.; Pradhan, V.R.

1995-08-01

This report presents the results of work which included extensive modifications to HRI`s existing 3 ton per day Process Development Unit (PDU) and completion of the first PDU run. The 58-day Run 1 demonstrated scale-up of the Catalytic Two-Stage Liquefaction (CTSL Process) on Illinois No. 6 coal to produce distillate liquid products at a rate of up to 5 barrels per to of moisture-ash-free coal. The Kerr McGee Rose-SR unit from Wilsonville was redesigned and installed next to the US Filter installation to allow a comparison of the two solids removal systems. Also included was a new enclosed reactor tower,more » upgraded computer controls and a data acquisition system, an alternate power supply, a newly refurbished reactor, an in-line hydrotreater, interstage sampling system, coal handling unit, a new ebullating pump, load cells and improved controls and remodeled preheaters. Distillate liquid yields of 5 barrels/ton of moisture ash free coal were achieved. Coal slurry recycle rates were reduced from the 2--2.5 to 1 ratio demonstrated at Wilsonville to as low as 0.9 to 1. Coal feed rates were increased during the test by 50% while maintaining process performance at a marginally higher reactor severity. Sulfur in the coal was reduced from 4 wt% to ca. 0.02 wt% sulfur in the clean distillate fuel product. More than 3,500 gallons of distillate fuels were collected for evaluation and upgrading studies. The ROSE-SR Process was operated for the first time with a pentane solvent in a steady-state model. The energy rejection of the ash concentrate was consistently below prior data, being as low as 12%, allowing improved liquid yields and recovery.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nabeel, A.; Khan, M.A.; Husain, S.

Coal is the most abundant source of energy. However, there is a need to develop cleaner, and more efficient, economical, and convenient coal conversion technologies. It is important to understand the organic chemical structure of coal for achieving real breakthroughs in the development of such coal conversion technologies. A novel computer-assisted modeling technique based on the analysis of {sup 13}C NMR and gel permeation chromatography has been applied to predict the average molecular structure of the acetylated product of a depolymerized bituminous Indian coal. The proposed molecular structure may be of practical use in understanding the mechanism of coal conversionsmore » during the processes of liquefaction, gasification, combustion, and carbonization.« less

Solvent treatment of coal for improved liquefaction

DOEpatents

Appell, Herbert R.; Narain, Nand K.; Utz, Bruce R.

1986-05-06

Increased liquefaction yield is obtained by pretreating a slurry of solid carbonaceous material and a liquid hydrocarbonaceous solvent at a temperature above 200.degree. C. but below 350.degree. C. for a period of 10 minutes to four hours prior to exposure to liquefaction temperatures.

Separating liquid and solid products of liquefaction of coal or like carbonaceous materials

DOEpatents

Malek, John M.

1979-06-26

Slurryform products of coal liquefaction are treated with caustic soda in presence of H.sub.2 O in an inline static mixer and then the treated product is separated into a solids fraction and liquid fractions, including liquid hydrocarbons, by gravity settling preferably effected in a multiplate settling separator with a plurality of settling spacings.

Corrosion inhibition for distillation apparatus

DOEpatents

Baumert, Kenneth L.; Sagues, Alberto A.; Davis, Burtron H.; Schweighardt, Frank K.

1985-01-01

Tower material corrosion in an atmospheric or sub-atmospheric distillation tower in a coal liquefaction process is reduced or eliminated by subjecting chloride-containing tray contents to an appropriate ion-exchange resin to remove chloride from such tray contents materials.

Coal liquefaction: A research and development needs assessment: Final report, Volume II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schindler, H.D.; Burke, F.P.; Chao, K.C.

1989-03-01

Volume II of this report on an assessment of research needs for coal liquefaction contains reviews of the five liquefaction technologies---direct, indirect, pyrolysis, coprocessing, and bioconversion. These reviews are not meant to be encyclopedic; several outstanding reviews of liquefaction have appeared in recent years and the reader is referred to these whenever applicable. Instead, these chapters contain reviews of selected topics that serve to support the panel's recommendations or to illustrate recent accomplishments, work in progress, or areas of major research interest. At the beginning of each of these chapters is a brief introduction and a summary of the mostmore » important research recommendations brought out during the panel discussions and supported by the material presented in the review. A review of liquefaction developments outside the US is included. 594 refs., 100 figs., 60 tabs.« less

Coal liquefaction by base-catalyzed hydrolysis with CO.sub.2 capture

DOEpatents

Xiao, Xin

2014-03-18

The one-step hydrolysis of diverse biomaterials including coal, cellulose materials such as lumber and forestry waste, non-food crop waste, lignin, vegetable oils, animal fats and other source materials used for biofuels under mild processing conditions which results in the formation of a liquid fuel product along with the recovery of a high purity CO.sub.2 product is provided.

Coal-oil slurry preparation

DOEpatents

Tao, John C.

1983-01-01

A pumpable slurry of pulverized coal in a coal-derived hydrocarbon oil carrier which slurry is useful as a low-ash, low-sulfur clean fuel, is produced from a high sulfur-containing coal. The initial pulverized coal is separated by gravity differentiation into (1) a high density refuse fraction containing the major portion of non-coal mineral products and sulfur, (2) a lowest density fraction of low sulfur content and (3) a middlings fraction of intermediate sulfur and ash content. The refuse fraction (1) is gasified by partial combustion producing a crude gas product from which a hydrogen stream is separated for use in hydrogenative liquefaction of the middlings fraction (3). The lowest density fraction (2) is mixed with the liquefied coal product to provide the desired fuel slurry. Preferably there is also separately recovered from the coal liquefaction LPG and pipeline gas.

Chemical and physical aspects of refining coal liquids

NASA Astrophysics Data System (ADS)

Shah, Y. T.; Stiegel, G. J.; Krishnamurthy, S.

1981-02-01

Increasing costs and declining reserves of petroleum are forcing oil importing countries to develop alternate energy sources. The direct liquefaction of coal is currently being investigated as a viable means of producing substitute liquid fuels. The coal liquids derived from such processes are typically high in nitrogen, oxygen and sulfur besides having a high aromatic and metals content. It is therefore envisaged that modifications to existing petroleum refining technology will be necessary in order to economically upgrade coal liquids. In this review, compositional data for various coal liquids are presented and compared with those for petroleum fuels. Studies reported on the stability of coal liquids are discussed. The feasibility of processing blends of coal liquids with petroleum feedstocks in existing refineries is evaluated. The chemistry of hydroprocessing is discussed through kinetic and mechanistic studies using compounds which are commonly detected in coal liquids. The pros and cons of using conventional petroleum refining catalysts for upgrading coal liquids are discussed.

Direct coal liquefaction baseline design and system analysis. Quarterly report, January--March 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-04-01

The primary objective of the study is to develop a computer model for a base line direct coal liquefaction design based on two stage direct coupled catalytic reactors. This primary objective is to be accomplished by completing the following: a base line design based on previous DOE/PETC results from Wilsonville pilot plant and other engineering evaluations; a cost estimate and economic analysis; a computer model incorporating the above two steps over a wide range of capacities and selected process alternatives; a comprehensive training program for DOE/PETC Staff to understand and use the computer model; a thorough documentation of all underlyingmore » assumptions for baseline economics; and a user manual and training material which will facilitate updating of the model in the future.« less

Direct coal liquefaction baseline design and system analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-04-01

The primary objective of the study is to develop a computer model for a base line direct coal liquefaction design based on two stage direct coupled catalytic reactors. This primary objective is to be accomplished by completing the following: a base line design based on previous DOE/PETC results from Wilsonville pilot plant and other engineering evaluations; a cost estimate and economic analysis; a computer model incorporating the above two steps over a wide range of capacities and selected process alternatives; a comprehensive training program for DOE/PETC Staff to understand and use the computer model; a thorough documentation of all underlyingmore » assumptions for baseline economics; and a user manual and training material which will facilitate updating of the model in the future.« less

Power recovery system for coal liquefaction process

DOEpatents

Horton, Joel R.

1985-01-01

Method and apparatus for minimizing energy required to inject reactant such as coal-oil slurry into a reaction vessel, using high pressure effluent from the latter to displace the reactant from a containment vessel into the reaction vessel with assistance of low pressure pump. Effluent is degassed in the containment vessel, and a heel of the degassed effluent is maintained between incoming effluent and reactant in the containment vessel.

Control technology appendices for pollution control technical manuals. Final report, June 1982-February 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1983-04-01

The document is one of six technical handbooks prepared by EPA to help government officials granting permits to build synfuels facilities, synfuels process developers, and other interested parties. They provide technical data on waste streams from synfuels facilities and technologies capable of controlling them. Process technologies covered in the manuals include coal gasification, coal liquefaction by direct and idirect processing, and the extraction of oil from shale. The manuals offer no regulatory guidance, allowing the industry flexibility in deciding how best to comply with environmental regulations.

Method for separating liquid and solid products of liquefaction of coal or like carbonaceous materials

DOEpatents

Malek, John M.

1978-04-18

A method of improving the quality of slurry products taken from coal liquefaction reactors comprising subjecting the slurry to treatment with an alkaline compound such as caustic soda in the presence of steam in order to decompose the phenolic and acidic materials present in the slurry, and to also lower the slurry viscosity to allow separation of solid particles by sedimentation.

Pre-feasibility study for construction of a commercial coal hydrogenation plant

NASA Astrophysics Data System (ADS)

Hahn, W.; Wilhelm, H.; Kleinhueckelkotten, H.; Schmedeshagen, B.

1982-11-01

The technical problems, a suitable site and the unsatisfactory economics hinder the realization of a commercial coal liquefaction plant in Germany were identified. It is found that a plant for hydrogenation of coal and heavy oil according to the updated bergius-Pier process can be built. The improvement of acceptable reactor loading and increase of product yield was considered. The infrastructure aspects of a site for the plant which covers 300 hectars as well as eventually existing atmospheric pollution conditions in the environment are also considered.

Evaluation of selected elastomer O-ring pump seals for service at the Wilsonville, Alabama, Advanced Coal Liquefaction Research and Development Facility. [Ethylenepropylenediene monomer compounds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Skena, C.C.; Keiser, J.R.

1986-08-01

Previous laboratory tests of elastomer O-rings in coal liquefaction solvents conducted at L'Garde, Inc., indicated that certain ethylenepropylenediene monomer (EPDM) compounds provided the best performance when a backup ring was used to limit swelling. Before service testing in a pump at the Wilsonville, Alabama, Advanced Coal Liquefaction Research and Development Facility, tests of six selected elastomers in the appropriate Wilsonville-produced solvent were conducted at Oak Ridge National Laboratory (ORNL). The ORNL tests measured the elastomers' changes in cross section, weight, density, and relative flexibility. Although two perfluoroelastomers showed less degradation of most properties during these tests, it was decided tomore » proceed with service testing of two EPDM elastomers because of their much lower cost. 5 refs., 14 figs., 7 tabs.« less

Catalyst for coal liquefaction process

DOEpatents

Huibers, Derk T. A.; Kang, Chia-Chen C.

1984-01-01

An improved catalyst for a coal liquefaction process; e.g., the H-Coal Process, for converting coal into liquid fuels, and where the conversion is carried out in an ebullated-catalyst-bed reactor wherein the coal contacts catalyst particles and is converted, in addition to liquid fuels, to gas and residual oil which includes preasphaltenes and asphaltenes. The improvement comprises a catalyst selected from the group consisting of the oxides of nickel molybdenum, cobalt molybdenum, cobalt tungsten, and nickel tungsten on a carrier of alumina, silica, or a combination of alumina and silica. The catalyst has a total pore volume of about 0.500 to about 0.900 cc/g and the pore volume comprises micropores, intermediate pores and macropores, the surface of the intermediate pores being sufficiently large to convert the preasphaltenes to asphaltenes and lighter molecules. The conversion of the asphaltenes takes place on the surface of micropores. The macropores are for metal deposition and to prevent catalyst agglomeration. The micropores have diameters between about 50 and about 200 angstroms (.ANG.) and comprise from about 50 to about 80% of the pore volume, whereas the intermediate pores have diameters between about 200 and 2000 angstroms (.ANG.) and comprise from about 10 to about 25% of the pore volume, and the macropores have diameters between about 2000 and about 10,000 angstroms (.ANG.) and comprise from about 10 to about 25% of the pore volume. The catalysts are further improved where they contain promoters. Such promoters include the oxides of vanadium, tungsten, copper, iron and barium, tin chloride, tin fluoride and rare earth metals.

Refining and end use study of coal liquids I - pilot plant studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erwin, J.; Moulton, D.S.

1995-12-31

The Office of Fossil Energy, Pittsburgh Energy Technology Center is examining the ways in which coal liquids may best be integrated into the refinery of the 2000-2015 time frame and what performance and emission properties will prevail among the slate of fuels produced. The study consists of a Basic Program administered by Bechtel Group, Inc. to build a linear programming refinery model and provide processing and fuel properties data through subcontractors Southwest Research Institute, Amoco Oil R&D, and M.W. Kellogg Company. The model will be used in an Option 1 to devise a slate of test fuels meeting advanced specifications,more » which will be produced and tested for physical ASTM-type properties, engine performance, and vehicle emissions. Three coal liquids will be included: a direct liquid from bituminous coal, another from subbituminous, and a Fischer-Tropsch indirect liquefaction product. This paper reports the work to date on fractions of the first direct liquid including naphtha hydrotreating, heavy distillate hydrotreating, FCC of the heavy distillate hydrotreater products. Also reported are the first stages of work on the indirect liquefaction wax including feed preparation and FCC tests of blends with petroleum FCC feed.« less

Low severity coal liquefaction promoted by cyclic olefins. Quarterly report, January--March 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curtis, C.W.

Previous research has suggested that using a more effective hydrogen donor solvent in the low severity coal liquefaction reaction improves coal conversion. In order to understand the results of these methods, both independently and combined, a factorial experiment was designed. Pretreating coal with hydrochloric and sulfurous acid solutions in both water and methanol is compared with pretreating coal using only methanol and with no pretreatment. The effects of these pretreatments on coal liquefaction behavior are contrasted with the ammonium acetate pretreatment. Within each of these, individual reactions are performed with the hydroaromatic 1,2,3,4-tetrahydronaphthalene (tetralin, TET) and the cyclic olefin 1,4,5,8-tetrahydronaphthalenemore » (isotetralin, ISO). The final aspect of the factorial experiment is the comparison of Wyodak subbituminous coal (WY) from the Argonne Premium Sample Bank and Black Thunder subbituminous coal (BT) provided by Amoco. Half of the reactions in the matrix have now been completed. In all but one case, Black Thunder-HCl/H{sub 2}O, the ISO proved to be more reactive than TET. After the other four reactions using this combination are complete, the average conversion may be greater with the cyclic olefin. The second part of this paper describes the current and future work with Fourier transform infrared spectroscopy. The objective of this work is to determine the kinetics of reaction of isotetralin at high temperatures and pressures. This quarter combinations of three products typically produced from isotetralin were used in spectral subtraction.« less

Part 1. The effect of microwave receptors on the liquefaction of Turkish coals by microwave energy in a hydrogen donor solvent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Emine Yagmur; Taner Togrul

2005-12-01

The effects of microwave receptors to coal (receptor/coal) ratio and the period of heating by microwave energy on the solubilization of Turkish coals (Tuncbilek, Mugla-Yatagan, Beypazari lignites, and Zonguldak bituminous coal) in tetralin have been investigated. V{sub 2}O{sub 5} and TiO{sub 2} were used as microwave receptors. The changes of liquid product yield indicated that it depended significantly on the type and amount of receptor and the type of coal. A significant increase in the lignite conversions to oil fractions was observed by the addition of the V{sub 2}O{sub 5} receptor. The use of TiO{sub 2} receptor decreased the yieldmore » of THF soluble coal products. However, both V{sub 2}O{sub 5} and TiO{sub 2} receptors decreased the yield of preasphaltene (PAS) and asphaltene (AS) due to their catalytic effect on the coal liquefaction. 15 refs., 9 figs., 1 tab.« less

Liquefaction of coal by Polyporus versicolor and Poria monticola. Progress report, 1 January-31 March 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cohen, M.S.

1985-01-01

Both Polyporus versicolor and Poria monticola were obtained from the American Type Culture Collection. Growth of Polyporus was shown to be faster and stronger than that of Poria under all conditions tested and the results reported here are based upon liquefaction of lignite coal by Polyporus. The liquefied coal samples were treated with acetonitrile which gave two fractions, a black precipitate and a light yellow liquid phase supernatant. This supernatant consists of acetonitrile and organic compounds which are soluble in acetonitrile. If the supernatant is drawn off with a Pasteur pipette followed by addition of water to the black precipitate,more » the precipitate dissolves instantly in the water producing a black liquid. Using these techniques, the products of coal liquefaction have been divided into two phases which are soluble either in acetonitrile or in water. Both fractions have been analyzed by HPLC and compounds have been partially separated. No peaks have been identified. However, two principal peaks of the acetonitrile fraction have been sent to PETC for chemical analysis by GC-MS. 9 figs.« less

Research on solvent-refined coal. Quarterly technical progress report, April 1, 1981-June 30, 1981

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1981-10-01

This report describes progress on the Research on Solvent Refined Coal project by The Pittsburg and Midway Coal Mining Co.'s Merriam Laboratory during the second quarter of 1981. Alexander Mine coal was evaluated as a feedstock for major liquefaction facilities and had a yield structure similar to other reactive Pittsburgh seam coals at standard SRC II conditions. Two lots of coal from the Ireland Mine (Pittsburgh seam) were found to be of nearly the same composition and produced essentially the same yields. Two experiments in which coal-derived nonvolatile organic matter was processed without fresh coal feed indicate constant rates ofmore » conversion of SRC to oil and gas. Insoluble organic matter (IOM) remained unconverted. The naphtha and middle distillate products from the deep conversion contained less sulfur but more nitrogen than those from conventional SRC II processing. Encouraging results were obtained when a very small amount of iron oxide dispersed on alumina was added to Kaiparowits coal which cannot be processed at normal SRC II conditions without added catalyst. Subbituminous coals from the McKinley and Edna Mines were processed successfully with added pyrite but would not run when the added catalyst was removed.« less

Hydroliquefaction of coal

DOEpatents

Sze, Morgan C.; Schindler, Harvey D.

1982-01-01

Coal is catalytically hydroliquefied by passing coal dispersed in a liquefaction solvent and hydrogen upwardly through a plurality of parallel expanded catalyst beds, in a single reactor, in separate streams, each having a cross-sectional flow area of no greater than 255 inches square, with each of the streams through each of the catalyst beds having a length and a liquid and gas superficial velocity to maintain an expanded catalyst bed and provide a Peclet Number of at least 3. If recycle is employed, the ratio of recycle to total feed (coal and liquefaction solvent) is no greater than 2:1, based on volume. Such conditions provide for improved selectivity to liquid product to thereby reduce hydrogen consumption. The plurality of beds are formed by partitions in the reactor.

Utilization of coal as a source of chemicals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Demirbas, A.

Coal consists carbon-based substances can be used as a source of specialty aromatic chemicals and aliphatic chemicals. Four widespread processes allow for making chemicals from coals: gasification, liquefaction, direct conversion, and co-production of chemicals and fuels along with electricity. Coal is gasified to produce synthesis gas (syngas) with a gasifier which is then converted to paraffinic liquid fuels and chemicals by Fischer-Tropsch synthesis. Liquid product from coal gasification mainly contains benzene, toluene, xylene (BTX), phenols, alkylphenols, and cresol. Methanol is made using coal or syngas with hydrogen and carbon monoxide in a 2 to 1 ratio. Coal-derived methanol has manymore » preferable properties as it is free of sulfur and other impurities. Syngas from coal can be reformed to hydrogen. Ammonium sulfate from coal tar by pyrolysis can be converted to ammonia. The humus substances can be recovered from brown coal by alkali extraction.« less

Engineering kinetics of short residence time coal liquefaction processes

NASA Astrophysics Data System (ADS)

Traeger, R. K.

1980-06-01

Conversion of coal to liquid products occurs rapidly at temperatures over 350 C and can be significant in preheaters or short residence time reactors. The extent of conversion can have an effect on the operation of preheaters or effectiveness of subsequent reactors. To obtain process information, Illinois No. 6 coal in SRC II heavy distillate was reacted at 13.8 MPa, temperatures of 400, 425, and 450 C, and at slurry space velocities of 3200-96,000 kg/h-cu m. Product compositions and viscosities were measured. High concentrations of preasphaltenes occur in early reactions resulting in a high viscosity product, but subsequent reactions to asphaltenes and oils are less rapid.

Surfactant studies for bench-scale operation

NASA Technical Reports Server (NTRS)

Hickey, Gregory S.; Sharma, Pramod K.

1992-01-01

A phase 2 study was initiated to investigate surfactant-assisted coal liquefaction, with the objective of quantifying the enhancement in liquid yields and product quality. This publication covers the first quarter of work. The major accomplishments were: the refurbishment of the high-pressure, high-temperature reactor autoclave, the completion of four coal liquefaction runs with Pittsburgh #8 coal, two each with and without sodium lignosulfonate surfactant, and the development of an analysis scheme for the product liquid filtrate and filter cake. Initial results at low reactor temperatures show that the addition of the surfactant produces an improvement in conversion yields and an increase in lighter boiling point fractions for the filtrate.

Liquefaction process

DOEpatents

Poddar, Syamal K.

1981-01-01

Scale formation during the liquefaction of lower ranking coals and similar carbonaceous materials is significantly reduced and/or prevented by pretreatment with a combination of pretreating agents comprising SO.sub.2 and an oxidizing agent. It is essential to effective operation that the moisture content of the solid carbonaceous material be within the range from about 10 to about 25 wt %, based on dry solid carbonaceous material, during the pretreatment. The pretreatment is believed to convert at least a portion of the scale-forming components and particularly calcium, to the corresponding sulfate prior to liquefaction. The pretreatment may be accomplished with the combination of pretreating agents either simultaneously by using a mixture comprising SO.sub.2 and a gaseous oxidizing agent or sequentially by first treating with SO.sub.2 and then with an oxidizing agent.

Instrumental methods of analysis of sulfur compounds in synfuel process streams. Quarterly technical progress report, July-September 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jordan, J.; Talbott, J.

1984-01-01

Task 1. Methods development for the speciation of the polysulfides. Work on this task has been completed in December 1983 and reported accordingly in DOE/PC/40783-T13. Task 2. Methods development for the speciation of dithionite and polythionates. Work on Task 2 has been completed in June 1984 and has been reported accordingly in DOE/PC/40783-T15. Task 3. Total accounting of the sulfur balance in representative samples of synfuel process streams. A systematic and critical comparison of results, obtained in the analysis of sulfur moieties in representative samples of coal conversion process streams, revealed the following general trends. (a) In specimens of highmore » pH (9-10) and low redox potential (-0.3 to -0.4 volt versus NHE) sulfidic and polysulfidic sulfur moieties predominate. (b) In process streams of lower pH and more positive redox potential, higher oxidation states of sulfur (notably sulfate) account for most of the total sulfur present. (c) Oxidative wastewater treatment procedures by the PETC stripping process convert lower oxidation states of sulfur into thiosulfate and sulfate. In this context, remarkable similarities were observed between liquefaction and gasification process streams. However, the thiocyanate present in samples from the Grand Forks gasifier were impervious to the PETC stripping process. (d) Total sulfur contaminant levels in coal conversion process stream wastewater samples are primarily determined by the abundance of sulfur in the coal used as starting material than by the nature of the conversion process (liquefaction or gasification). 13 references.« less

Superacid Catalyzed Coal Conversion Chemistry. Final Technical Report, September 1, 1983-September 1, 1986

DOE R&D Accomplishments Database

Olah, G. A.

1986-01-01

This research project involved the study of a raw comparatively mild coal conversion process. The goal of the project was to study model systems to understand the basic chemistry involved and to provide a possible effective pretreatment of coal which significantly improves liquefaction-depolymerization under mild conditions. The conversion process operates at relatively low temperatures (170 degrees C) and pressures and uses an easily recyclable, stable superacid catalysts (HF-BF{sub 3}). It consequently offers an attractive alternative to currently available processes. From the present studies it appears that the modification of coal structure by electrophilic alkylation and subsequent reaction of alkylated coal with HF-BF{sub 3}-H{sub 2} system under mild conditions considerably improves the extractability of coal in pyridine and cyclohexane. On the other hand, nitration of coal and its subsequent reaction with HF-BF{sub 3}H{sub 2} decreases the pyridine and cyclohexane extractability. Study of model compounds under conditions identical with the superacidic HF/BF{sub 3}/H{sub 2} system provided significant information about the basic chemistry of the involved cleavage-hydrogenation reactions.

Model for refining operations

NASA Technical Reports Server (NTRS)

Dunbar, D. N.; Tunnah, B. G.

1979-01-01

Program predicts production volumes of petroleum refinery products, with particular emphasis on aircraft-turbine fuel blends and their key properties. It calculates capital and operating costs for refinery and its margin of profitability. Program also includes provisions for processing of synthetic crude oils from oil shale and coal liquefaction processes and contains highly-detailed blending computations for alternative jet-fuel blends of varying endpoint specifications.

Advanced thermally stable jet fuels: Technical progress report, October 1994--December 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schobert, H.H.; Eser, S.; Song, C.

There are five tasks within this project on thermally stable coal-based jet fuels. Progress on each of the tasks is described. Task 1, Investigation of the quantitative degradation chemistry of fuels, has 5 subtasks which are described: Literature review on thermal stability of jet fuels; Pyrolytic and catalytic reactions of potential endothermic fuels: cis- and trans-decalin; Use of site specific {sup 13}C-labeling to examine the thermal stressing of 1-phenylhexane: A case study for the determination of reaction kinetics in complex fuel mixtures versus model compound studies; Estimation of critical temperatures of jet fuels; and Surface effects on deposit formation inmore » a flow reactor system. Under Task 2, Investigation of incipient deposition, the subtask reported is Uncertainty analysis on growth and deposition of particles during heating of coal-derived aviation gas turbine fuels; under Task 3, Characterization of solid gums, sediments, and carbonaceous deposits, is subtask, Studies of surface chemistry of PX-21 activated carbon during thermal degradation of jet A-1 fuel and n-dodecane; under Task 4, Coal-based fuel stabilization studies, is subtask, Exploratory screening and development potential of jet fuel thermal stabilizers over 400 C; and under Task 5, Exploratory studies on the direct conversion of coal to high quality jet fuels, are 4 subtasks: Novel approaches to low-severity coal liquefaction and coal/resid co-processing using water and dispersed catalysts; Shape-selective naphthalene hydrogenation for production of thermally stable jet fuels; Design of a batch mode and a continuous mode three-phase reactor system for the liquefaction of coal and upgrading of coal liquids; and Exploratory studies on coal liquids upgrading using mesopores molecular sieve catalysts. 136 refs., 69 figs., 24 tabs.« less

RESEARCH TO IDENTIFY COMPONENTS OF ENERGY-RELATED WASTES: A STATE-OF-THE-ART REPORT

EPA Science Inventory

Pertinent abstracts from a survey of current (post-1976) research projects are categorized according to energy-related activity. Subjects include coal strip mines, oil refineries, oil shale operations, coal-fired power plants, geothermal energy production, coal liquefaction plant...

Method of producing a colloidal fuel from coal and a heavy petroleum fraction. [partial liquefaction of coal in slurry, filtration and gasification of residue

DOEpatents

Longanbach, J.R.

1981-11-13

A method is provided for combining coal as a colloidal suspension within a heavy petroleum fraction. The coal is broken to a medium particle size and is formed into a slurry with a heavy petroleum fraction such as a decanted oil having a boiling point of about 300 to 550/sup 0/C. The slurry is heated to a temperature of 400 to 500/sup 0/C for a limited time of only about 1 to 5 minutes before cooling to a temperature of less than 300/sup 0/C. During this limited contact time at elevated temperature the slurry can be contacted with hydrogen gas to promote conversion. The liquid phase containing dispersed coal solids is filtered from the residual solids and recovered for use as a fuel or feed stock for other processes. The residual solids containing some carbonaceous material are further processed to provide hydrogen gas and heat for use as required in this process.

Direct use of methane in coal liquefaction

DOEpatents

Sundaram, Muthu S.; Steinberg, Meyer

1987-01-01

This invention relates to a process for converting solid carbonaceous material, such as coal, to liquid and gaseous hydrocarbons utilizing methane, generally at a residence time of about 20-120 minutes at a temperature of 250.degree.-750.degree. C., preferably 350.degree.-450.degree. C., pressurized up to 6000 psi, and preferably in the 1000-2500 psi range, preferably directly utilizing methane 50-100% by volume in a mix of methane and hydrogen. A hydrogen donor solvent or liquid vehicle such as tetralin, tetrahydroquinoline, piperidine, and pyrolidine may be used in a slurry mix where the solvent feed is 0-100% by weight of the coal or carbonaceous feed. Carbonaceous feed material can either be natural, such as coal, wood, oil shale, petroleum, tar sands, etc., or man-made residual oils, tars, and heavy hydrocarbon residues from other processing systems.

System for analyzing coal liquefaction products

DOEpatents

Dinsmore, Stanley R.; Mrochek, John E.

1984-01-01

A system for analyzing constituents of coal-derived materials comprises three adsorption columns and a flow-control arrangement which permits separation of both aromatic and polar hydrocarbons by use of two eluent streams.

Direct coal liquefaction process

DOEpatents

Rindt, John R.; Hetland, Melanie D.

1993-01-01

An improved multistep liquefaction process for organic carbonaceous mater which produces a virtually completely solvent-soluble carbonaceous liquid product. The solubilized product may be more amenable to further processing than liquid products produced by current methods. In the initial processing step, the finely divided organic carbonaceous material is treated with a hydrocarbonaceous pasting solvent containing from 10% and 100% by weight process-derived phenolic species at a temperature within the range of 300.degree. C. to 400.degree. C. for typically from 2 minutes to 120 minutes in the presence of a carbon monoxide reductant and an optional hydrogen sulfide reaction promoter in an amount ranging from 0 to 10% by weight of the moisture- and ash-free organic carbonaceous material fed to the system. As a result, hydrogen is generated via the water/gas shift reaction at a rate necessary to prevent condensation reactions. In a second step, the reaction product of the first step is hydrogenated.

Direct coal liquefaction process

DOEpatents

Rindt, J.R.; Hetland, M.D.

1993-10-26

An improved multistep liquefaction process for organic carbonaceous mater which produces a virtually completely solvent-soluble carbonaceous liquid product. The solubilized product may be more amenable to further processing than liquid products produced by current methods. In the initial processing step, the finely divided organic carbonaceous material is treated with a hydrocarbonaceous pasting solvent containing from 10% and 100% by weight process-derived phenolic species at a temperature within the range of 300 C to 400 C for typically from 2 minutes to 120 minutes in the presence of a carbon monoxide reductant and an optional hydrogen sulfide reaction promoter in an amount ranging from 0 to 10% by weight of the moisture- and ash-free organic carbonaceous material fed to the system. As a result, hydrogen is generated via the water/gas shift reaction at a rate necessary to prevent condensation reactions. In a second step, the reaction product of the first step is hydrogenated.

Direct use of methane in coal liquefaction

DOEpatents

Sundaram, M.S.; Steinberg, M.

1985-06-19

This invention relates to a process for converting solid carbonaceous material, such as coal, to liquid and gaseous hydrocarbons utilizing methane, generally at a residence time of about 20 to 120 minutes at a temperature of 250 to 750/sup 0/C, preferably 350 to 450/sup 0/C, pressurized up to 6000 psi, and preferably in the 1000 to 2500 psi range, preferably directly utilizing methane 50 to 100% by volume in a mix of methane and hydrogen. A hydrogen donor solvent or liquid vehicle such as tetralin, tetrahydroquinoline, piperidine, and pyrolidine may be used in a slurry mix where the solvent feed is 0 to 100% by weight of the coal or carbonaceous feed. Carbonaceous feed material can either be natural, such as coal, wood, oil shale, petroleum, tar sands, etc., or man-made residual oils, tars, and heavy hydrocarbon residues from other processing systems. 1 fig.

Run 263 with Black Thunder Mine subbituminous coal and dispersed molybdenum catalysts. Technical progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This report presents the results of Run 263 performed at the Advanced Coal Liquefaction R&D Facility in Wilsonville, Alabama. The run started on October 31, 1991 and continued until February 23, 1992. Tests were conducted by operating the reactors in the Close-Coupled Integrated Two-Stage Liquefaction mode and by processing Black Thunder Mine subbituminous coal from Wyodak-Anderson seam in Wyoming Powder River Basin. Half volume reactors were used for the entire run. In the first part of Run 263, a dispersed molybdenum catalyst was evaluated for its performance without a supported catalyst in the second stage. Molyvan L and Molyvan 822more » (commercially available as friction reducing lubricants) were used as precursors for the dispersed molybdenum catalyst. The effect of the dispersed catalyst on eliminating the solids buildup was also evaluated. For the second part of the run, the hybrid catalyst system was tested with supported Criterion 324 1/1611 catalyst in the second stage at catalyst replacement rates of 2 and 3 lb/ton of MF coal. The molybdenum concentration was 100--200 ppm based on MF coal. Iron oxide was used as a slurry catalyst precursor at a rate of 1--2 wt % MF coal throughout the run with dimethyl disulfide (DMDS) as the sulfiding agent. The close-coupled reactor unit was on-stream for 2482 hours for an on-stream factor of 91.2% and the ROSE-SR{sup sm} unit was on-feed for 2126 hours for an on-stream factor of 96.4% for the entire run.« less

Run 263 with Black Thunder Mine subbituminous coal and dispersed molybdenum catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This report presents the results of Run 263 performed at the Advanced Coal Liquefaction R D Facility in Wilsonville, Alabama. The run started on October 31, 1991 and continued until February 23, 1992. Tests were conducted by operating the reactors in the Close-Coupled Integrated Two-Stage Liquefaction mode and by processing Black Thunder Mine subbituminous coal from Wyodak-Anderson seam in Wyoming Powder River Basin. Half volume reactors were used for the entire run. In the first part of Run 263, a dispersed molybdenum catalyst was evaluated for its performance without a supported catalyst in the second stage. Molyvan L and Molyvanmore » 822 (commercially available as friction reducing lubricants) were used as precursors for the dispersed molybdenum catalyst. The effect of the dispersed catalyst on eliminating the solids buildup was also evaluated. For the second part of the run, the hybrid catalyst system was tested with supported Criterion 324 1/1611 catalyst in the second stage at catalyst replacement rates of 2 and 3 lb/ton of MF coal. The molybdenum concentration was 100--200 ppm based on MF coal. Iron oxide was used as a slurry catalyst precursor at a rate of 1--2 wt % MF coal throughout the run with dimethyl disulfide (DMDS) as the sulfiding agent. The close-coupled reactor unit was on-stream for 2482 hours for an on-stream factor of 91.2% and the ROSE-SR[sup sm] unit was on-feed for 2126 hours for an on-stream factor of 96.4% for the entire run.« less

Microbial liquefaction of peat for the production of synthetic fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gunasekaran, M.

1988-01-01

Objectives of this study were: to evaluate the potential of using various microorganisms to hydrolyse and liquify peat; to determine the optimal conditions for peat hydrolysis and liquefaction; to study the co-metabolizable substances; to separate the compounds present in liquified peat by alumina and silica acid chromatography and capillary gas chromatography; and to identify the compounds in liquified peat by capillary GC-Mass spectrometry. Organisms used in the study include: Coprinus comatus, Coriolus hirsutus, Ganoderma lucidum, Lentinus edodes, Lenzites trabea, Phanerochaete chrysosporium, Pleurotus ostreatus, P. sapidus, Polyporus adjustus, Neurospora sitophila, Rhizophus arrhizus, Bacillus subtilis, Acinetobacter sp. and Alcaligenes sp. The fungimore » were maintained and cultivated in potato dextrose agar at 30 C. The bacteria were maintained in nutrient agar at 30 C. We have also initiated work on coal solubilization in addition to the studies on peat liquefaction. A relatively new substratum or semi-solid base for culture media called Pluronic F-127, or Polyol (BASF, New Jersey). Objectives of this study were: (1) to study the growth patterns of Candida ML 13 on pluronic as substratum; (2) to determine the rate of microbial coal solubilization on pluronic F-127 amended in different growth media; (3) to separate the mycelial mat of Candida ML 13 from unsolubilized coal particles and solubilized coal products from pluronic F-127; (4) to determine the effects of pH on microbial coal solubilization in pluronic F-127 media; (5) the effect of concentration of pluronic F-127 in media on coal solubilization; and, (6) to study the role of extracellular factors secreted by Candida ML 13 on coal solubilization in pluronic F-127 media. Results are discussed. 4 refs.« less

30 CFR 1206.264 - In-situ and surface gasification and liquefaction operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false In-situ and surface gasification and... developed by in-situ or surface gasification or liquefaction technology, the lessee shall propose the value... ENFORCEMENT, DEPARTMENT OF THE INTERIOR Natural Resources Revenue PRODUCT VALUATION Federal Coal § 1206.264 In...

30 CFR 1206.463 - In-situ and surface gasification and liquefaction operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false In-situ and surface gasification and... developed by in-situ or surface gasification or liquefaction technology, the lessee shall propose the value... ENFORCEMENT, DEPARTMENT OF THE INTERIOR Natural Resources Revenue PRODUCT VALUATION Indian Coal § 1206.463 In...

Liquefaction chemistry and kinetics: Hydrogen utilization studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rothenberger, K.S.; Warzinski, R.P.; Cugini, A.V.

1995-12-31

The objectives of this project are to investigate the chemistry and kinetics that occur in the initial stages of coal liquefaction and to determine the effects of hydrogen pressure, catalyst activity, and solvent type on the quantity and quality of the products produced. The project comprises three tasks: (1) preconversion chemistry and kinetics, (2) hydrogen utilization studies, and (3) assessment of kinetic models for liquefaction. The hydrogen utilization studies work will be the main topic of this report. However, the other tasks are briefly described.

Hydrothermal pretreatment to prevent scale during liquefaction of certain solid carbonaceous materials

DOEpatents

Stone, John B.; Floyd, Frank M.

1984-01-01

Scale formation during the liquefaction of lower ranking coals and similar carbonaceous materials is significantly reduced and/or prevented by hydrothermal pretreatment. The said pretreatment is believed to convert the scale-forming components to the corresponding carbonate prior to liquefaction. The said pretreatment is accomplished at a total pressure within the range from about 1000 to about 4400 psia. Temperature during said pretreatment will generally be within the range from about 500.degree. to about 700.degree. F.

Hindered diffusion of coal liquids. Quarterly report No. 12, June 18, 1995--September 17, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsotsis, T.T.; Sahimi, M.; Webster, I.A.

1995-12-31

The design of industrial catalysts requires that the diffusivity of the reacting species within the catalyst be accurately known. Nowhere is this more important than in the area of coal liquefaction and upgrading of coal liquids. In this area one is faced with the task of processing a number of heavy oils, containing metals and other contaminants, in a variety of process dependent solvents. It is important, therefore, on the basis of predicting catalyst activity, selectivity, and optimizing reactor performance, that the diffusivities of these oil species be accurately known. It is the purpose of the project described here tomore » provide such a correct concept of coal asphaltenes by careful and detailed investigations of asphaltene transport through porous systems under realistic process temperature and pressure conditions. The experimental studies will be coupled with detailed, in-depth statistical and molecular dynamics models intended to provide a fundamental understanding of the overall transport mechanisms.« less

Liquefaction/solubilization of low-rank Turkish coals by white-rot fungus (Phanerochaete chrysosporium)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elbeyli, I.Y.; Palantoken, A.; Piskin, S.

2006-08-15

Microbial coal liquefaction/solubilization of three low-rank Turkish coals (Bursa-Kestelek, Kutahya-Seyitomer and Mugla-Yatagan lignite) was attempted by using a white-rot fungus (Phanerochaete chrysosporium DSM No. 6909); chemical compositions of the products were investigated. The lignite samples were oxidized by nitric acid under moderate conditions and then oxidized samples were placed on the agar medium of Phanerochaete chrysosporium. FTIR spectra of raw lignites, oxidized lignites and liquid products were recorded, and the acetone-soluble fractions of these samples were identified by GC-MS technique. Results show that the fungus affects the nitro and carboxyl/carbonyl groups in oxidized lignite sample, the liquid products obtained bymore » microbial effects are the mixture of water-soluble compounds, and show limited organic solubility.« less

Advanced direct coal liquefaction concepts. Quarterly report, January 1, 1994--March 31, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berger, D.J.; Parker, R.J.; Simpson, P.L.

A detailed evaluation of the bench unit data on Black Thunder feedstocks was completed. The results show that in a once-through operation using counterflow, reactor technology coal conversions in excess of 90% could be obtained, giving distillable oil yields in the range 60--65 wt % on MAF coal. The remaining non-distillable oil fraction which represents 20--25 wt % on MAF coal is a source of additional distillable oil in further processing, for example, bottoms recycle operation. C{sub 1}-C{sub 3} gas yields were generally in the order of 6--8 wt %. In autoclave studies, Illinois No. 6 coal was found tomore » be much less reactive than Black Thunder coal, and did not respond well to solubilization with carbon monoxide/steam. Process severity was, therefore, increased for bench unit operations on Illinois No. 6 coal, and work has concentrated on the use of hydrogen rather than carbon monoxide for solubilization. Preliminary coking studies on the resid from bench unit runs on Black Thunder coal were also carried out. Distillable liquid yields of 55--60 wt % were obtained. The technical and economic study to be carried out by Kilborn Engineering Company has been initiated.« less

Undergraduate research studies program at participating institutions of the HBCU Fossil Energy Consortium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bota, K.B.

1991-01-01

The primary objective of this research program is to expose students in the Historically Black Colleges and Universities (HBCU) Fossil Energy Consortium Institutions to energy and fossil fuels research, to stimulate their interest in the sciences and engineering and to encourage them to pursue graduate studies. This report provides the research accomplishment of the various students who participated in the program. Research results are presented on the following topics: Energy Enhancement and Pollutant Reduction in Coal by Cryogenic Diminution; Competition of NO and SO[sub 2] for OH Generated witin Electrical Aerosol Analyzers; Dispersed Iron Catalysts for Coal Gasification; NQR/NMR Studiesmore » of Copper-Cobalt Catalysts for Syngas Concersion; Catalytic gasification of Coal Chars by Potassium Sulfate and Ferrous Sulfate Mixtures; A New Method for Cleaning and Beneficiation of Ultrafine Coal; Characterization Studies of Coal-Derived Liquids; Study of Coal Liquefaction Catalysts and Removal of Certain Toxic Heavy Metal Ions from Coal Conversion Process Wastewaters.« less

Undergraduate research studies program at participating institutions of the HBCU Fossil Energy Consortium. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bota, K.B.

1991-12-31

The primary objective of this research program is to expose students in the Historically Black Colleges and Universities (HBCU) Fossil Energy Consortium Institutions to energy and fossil fuels research, to stimulate their interest in the sciences and engineering and to encourage them to pursue graduate studies. This report provides the research accomplishment of the various students who participated in the program. Research results are presented on the following topics: Energy Enhancement and Pollutant Reduction in Coal by Cryogenic Diminution; Competition of NO and SO{sub 2} for OH Generated witin Electrical Aerosol Analyzers; Dispersed Iron Catalysts for Coal Gasification; NQR/NMR Studiesmore » of Copper-Cobalt Catalysts for Syngas Concersion; Catalytic gasification of Coal Chars by Potassium Sulfate and Ferrous Sulfate Mixtures; A New Method for Cleaning and Beneficiation of Ultrafine Coal; Characterization Studies of Coal-Derived Liquids; Study of Coal Liquefaction Catalysts and Removal of Certain Toxic Heavy Metal Ions from Coal Conversion Process Wastewaters.« less

Pilot Plant Program for the AED Advanced Coal Cleaning System. Phase II. Interim final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-08-01

Advanced Energy Dynamics, Inc. (AED), has developed a proprietary coal cleaning process which employs a combination of ionization and electrostatic separation to remove both sulfur and ash from dry pulverized coal. The Ohio Department of Energy sponsored the first part of a program to evaluate, develop, and demonstrate the process in a continuous-flow pilot plant. Various coals used by Ohio electric utilities were characterized and classified, and sulfur reduction, ash reduction and Btu recovery were measured. Sulfur removal in various coals ranged from 33 to 68% (on a Btu basis). Ash removal ranged from 17 to 59% (on a Btumore » basis). Ash removal of particles greater than 53 microns ranged from 46 to 88%. Btu recovery ranged from 90 to 97%. These results, especially the large percentage removal of ash particles greater than 53 microns, suggest that the AED system can contribute materially to improved boiler performance and availability. The study indicated the following potential areas for commercial utilization of the AED process: installation between the pulverizer and boiler of conventional coal-fired power utilities; reclamation of fine coal refuse; dry coal cleaning to supplement, and, if necessary, to take the place of conventional coal cleaning; upgrading coal used in: (1) coal-oil mixtures, (2) gasification and liquefaction processes designed to handle pulverized coal; and (3) blast furnaces for making steel, as a fuel supplement to the coke. Partial cleaning of coking coal blends during preheating may also prove economically attractive. Numerous other industrial processes which use pulverized coal such as the production of activated carbon and direct reduction of iron ore may also benefit from the use of AED coal cleaning.« less

A Cost Estimation of Biofuels for Naval Aviation: Budgeting for the Great Green Fleet

DTIC Science & Technology

2011-12-01

from DLA-E, 2011).....10 Figure 8. Pathways for Biomass to Liquid Fuels Production (From Gorin, 2010) ........23 Figure 9. Simplified Process...edible biomass grown on marginal lands and coastal waters. Some are produced using coal to liquid technology. These may be the fuels of the future...liquefaction process  Renewable oils from biomass , and  Alcohols from fermentation of biomass (Hileman et al., 2009, p. 11) The report

Proceedings of the second US Department of Energy environmental control symposium. Volume 1. Fossil energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1980-06-01

These proceedings document the presentations given at the Second Environmental Control Symposium. Symposium presentations highlighted environmental control activities which span the entire DOE. Volume I contains papers relating to coal preparation, oil shales, coal combustion, advanced coal utilization (fluidized bed combustion, MHD generators, OCGT, fuel cells), coal gasification, coal liquefaction, and fossil resource extraction (enhanced recovery). Separate abstracts for individual papers are prepared for inclusion in the Energy Data Base. (DMC)

National Environmental Policy: Coordination or Confusion?

ERIC Educational Resources Information Center

Adams, Sexton; And Others

1976-01-01

The Fossil Energy Program is attempting to develop and demonstrate, in conjunction with industry, the technology necessary for establishing a synthetic fuels-from coal industry. Technologies discussed include coal liquefaction, high and low BTU gasification, advanced power systems, direct combustion, Magnetohydrodynamics (MHD) and petroleum,…

Recovery of Rare Earth Elements from Coal and Coal Byproducts via a Closed Loop Leaching Process: Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peterson, Richard; Heinrichs, Michael; Argumedo, Darwin

Objectives: Through this grant, Battelle proposes to address Area of Interest (AOI) 1 to develop a bench-scale technology to economically separate, extract, and concentrate mixed REEs from coal ash. U.S. coal and coal byproducts provide the opportunity for a domestic source of REEs. The DOE’s National Energy Technology Laboratory (NETL) has characterized various coal and coal byproducts samples and has found varying concentrations of REE ranging up to 1,000 parts per million by weight. The primary project objective is to validate the economic viability of recovering REEs from the coal byproduct coal ash using Battelle’s patented closed-loop Acid Digestion Processmore » (ADP). This will be accomplished by selecting coal sources with the potential to provide REE concentrations above 300 parts per million by weight, collecting characterization data for coal ash samples generated via three different methods, and performing a Techno-Economic Analysis (TEA) for the proposed process. The regional availability of REE-laden coal ash, the regional market for rare earth concentrates, and the system capital and operating costs for rare earth recovery using the ADP technology will be accounted for in the TEA. Limited laboratory testing will be conducted to generate the parameters needed for the design of a bench scale system for REE recovery. The ultimate project outcome will be the design for an optimized, closed loop process to economically recovery REEs such that the process may be demonstrated at the bench scale in a Phase 2 project. Project Description: The project will encompass evaluation of the ADP technology for the economic recovery of REEs from coal and coal ash. The ADP was originally designed and demonstrated for the U.S. Army to facilitate demilitarization of cast-cured munitions via acid digestion in a closed-loop process. Proof of concept testing has been conducted on a sample of Ohio-based Middle Kittanning coal and has demonstrated the feasibility of recovering REEs using the ADP technology. In AOI 1, Ohio coal sources with the potential to provide a consistent source of rare earth element concentrations above 300 parts per million will be identified. Coal sample inventories from West Virginia and Pennsylvania will also be assessed for purposes of comparison. Three methods of preparing the coal ash will be evaluated for their potential to enhance the technical feasibility and economics of REE recovery. Three sources of coal ash are targeted for evaluation of the economics of REE recovery in this project: (1) coal ash from power generation stations, to include fly ash and/or bottom ash, (2) ash generated in a lower temperature ashing process, and (3) ash residual from Battelle’s coal liquefaction process. Making use of residual ash from coal liquefaction processes directly leverages work currently being conducted by Battelle for DOE NETL in response to DE-FOA-0000981 entitled “Greenhouse Gas Emissions Reductions Research and Development Leading to Cost-Competitive Coal-to-Liquids Based Jet Fuel Production.” Using the sample characterization results and regional information regarding REE concentration, availability and cost, a TEA will be developed. The previously generated laboratory testing results for leaching and REE recovery via the ADP will be used to perform the TEA, along with common engineering assumptions for scale up of equipment and labor costs. Finally, upon validation of the economic feasibility of the process by the TEA, limited laboratory testing will be performed to support the design of a bench scale system. In a future project phase, it is envisioned that the bench scale system will be constructed and operated to prove the process on a continuous basis.« less

Anaerobic bioprocessing of low-rank coals. [Veillonella alcalescens and Propionibacterium acidipropionici

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jain, M.K.; Narayan, R.; Han, O.

1992-01-30

The overall goal of this project is to find biological methods to remove carboxylic functionalities from low-rank coals under ambient conditions and to assess the properties of these modified coals towards coal liquefaction. The main objectives of this quarter were: (1) continuation of microbial consortia development, (2) evaluation of the isolated organisms for decarboxylation, (3) selection of best performing culture (known cultures vs. new isolates), and (4) coal decarboxylation using activated carbon as blanks. The project began on September 12, 1990.

Novel bimetallic dispersed catalysts for temperature-programmed coal liquefaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chunshan, Song; Kirby, S.; Schmidt, E.

1995-12-31

The objective of this project is to explore bimetallic dispersed catalysts for more efficient coal liquefaction. Coal liquefaction involves cleavage of methylene, dimethylene and ether bridges connecting various aromatic units and the reactions of various oxygen functional groups. This paper describes recent results on (1) hydrodeoxygenation of O-containing polycyclic model compounds using novel organometallic catalyst precursors; and (2) activity and selectivity of dispersed Fe catalysts from organometallic and inorganic precursors for hydrocracking of 4-(1-naphthylmethyl) bibenzyl. The results showed that some iron containing catalysts have higher activity in the sulfur-free form, contrary to conventional wisdom. Adding sulfur to Fe precursors withmore » Cp-ligands decreased the activity of the resulting catalyst. This is in distinct contrast to the cases with iron pentacarbonyl and superfine Fe{sub 2}O{sub 3}, where S addition increased their catalytic activity substantially. A positive correlation between sulfur addition and increased activity can be seen, but a reversed trend between Fe cluster size and hydrocracking conversion could be observed, for carbonyl-type Fe precursors. It is apparent that the activity and selectivity of Fe catalysts for NMBB conversion depends strongly on both the type of ligand environment, the oxidation state and the number of intermetal bonds in the molecular precursor.« less

Enthalpy measurement of coal-derived liquids. Technical progress report, November 1982-January 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kidnay, A.J.; Yesavage, V.F.

The objective of this research is to measure the enthalpy for representative coal-derived liquids and model compounds over the pressure and temperature regions most likely to be encountered in both liquefaction and processing systems, and to prepare from the data an enthalpy correlation suitable for process design calculations. The correlational effort this past quarter on the enthalpy of coal-derived syncrudes and model compounds has emphasized the experimental determination of a correlating factor for association in coal liquids. As in previous work, the degree of association is to be related to cryoscopic molecular weight determinations on the coal liquids. To thismore » end, work on and an evaluationof a cryoscopic molecular weight apparatus was completed this quarter. Molecular weights of coal liquids determined by the standard Beckman freezing point depression apparatus were consistently low (5 to 10%). After modifications of the apparatus, it was tested with the following compounds: hexane, dodecane, m-xylene and naphthalene. Benzene was the solvent used. However, the molecular weight measurements were again consistently lower than the true values, and in many cases the experimental error was greater than that of the Beckman apparatus.« less

Cooling and solidification of heavy hydrocarbon liquid streams

DOEpatents

Antieri, Salvatore J.; Comolli, Alfred G.

1983-01-01

A process and apparatus for cooling and solidifying a stream of heavy hydrocarbon material normally boiling above about 850.degree. F., such as vacuum bottoms material from a coal liquefaction process. The hydrocarbon stream is dropped into a liquid bath, preferably water, which contains a screw conveyor device and the stream is rapidly cooled, solidified and broken therein to form discrete elongated particles. The solid extrudates or prills are then dried separately to remove substantially all surface moisture, and passed to further usage.

A CHARACTERIZATION AND EVALUATION OF COAL LIQUEFACTION PROCESS STREAMS

DOE Office of Scientific and Technical Information (OSTI.GOV)

G.A. Robbins; R.A. Winschel; S.D. Brandes

This is the first Annual Technical Report of activities under DOE Contract No. DE-AC22-94PC93054. Activities from the first three quarters of the fiscal 1998 year were reported previously as Quarterly Technical Progress Reports (DOE/PC93054-57, DOE/PC93054-61, and DOE/PC93054-66). Activities for the period July 1 through September 30, 1998, are reported here. This report describes CONSOL's characterization of process-derived samples obtained from HTI Run PB-08. These samples were derived from operations with Black Thunder Mine Wyoming subbituminous coal, simulated mixed waste plastics, and pyrolysis oils derived from waste plastics and waste tires. Comparison of characteristics among the PB-08 samples was made tomore » ascertain the effects of feed composition changes. A comparison also was made to samples from a previous test (Run PB-06) made in the same processing unit, with Black Thunder Mine coal, and in one run condition with co-fed mixed plastics.« less

Coking and gasification process

DOEpatents

Billimoria, Rustom M.; Tao, Frank F.

1986-01-01

An improved coking process for normally solid carbonaceous materials wherein the yield of liquid product from the coker is increased by adding ammonia or an ammonia precursor to the coker. The invention is particularly useful in a process wherein coal liquefaction bottoms are coked to produce both a liquid and a gaseous product. Broadly, ammonia or an ammonia precursor is added to the coker ranging from about 1 to about 60 weight percent based on normally solid carbonaceous material and is preferably added in an amount from about 2 to about 15 weight percent.

Proceedings of the Conference on Coal Use for California

NASA Technical Reports Server (NTRS)

1978-01-01

The papers, statements, and panel session transcriptions that resulted from the conference are presented. The conference brought together approximately 400 specialists, students, interest groups and general public for the examination of technological, institutional, and social issues surrounding coal use for California and the identification of attendant constraints, impediments, advantages, and target opportunities. The expertise of the participants cover a wide range of subject matter that includes systems examination of coal opportunities, energy demand forecasting, environmental aspects of coal use, coal supply and transport, viewpoint of neighboring states, air pollution control, direct firing, coal gasification and liquefaction technologies, economics of coal use, and the regulatory system.

Montana Integrated Carbon to Liquids (ICTL) Demonstration Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fiato, Rocco A.; Sharma, Ramesh; Allen, Mark

Integrated carbon-to-liquids technology (ICTL) incorporates three basic processes for the conversion of a wide range of feedstocks to distillate liquid fuels: (1) Direct Microcatalytic Coal Liquefaction (MCL) is coupled with biomass liquefaction via (2) Catalytic Hydrodeoxygenation and Isomerization (CHI) of fatty acid methyl esters (FAME) or trigylceride fatty acids (TGFA) to produce liquid fuels, with process derived (3) CO 2 Capture and Utilization (CCU) via algae production and use in BioFertilizer for added terrestrial sequestration of CO 2, or as a feedstock for MCL and/or CHI. This novel approach enables synthetic fuels production while simultaneously meeting EISA 2007 Section 526more » targets, minimizing land use and water consumption, and providing cost competitive fuels at current day petroleum prices. ICTL was demonstrated with Montana Crow sub-bituminous coal in MCL pilot scale operations at the Energy and Environmental Research Center at the University of North Dakota (EERC), with related pilot scale CHI studies conducted at the University of Pittsburgh Applied Research Center (PARC). Coal-Biomass to Liquid (CBTL) Fuel samples were evaluated at the US Air Force Research Labs (AFRL) in Dayton and greenhouse tests of algae based BioFertilizer conducted at Montana State University (MSU). Econometric modeling studies were also conducted on the use of algae based BioFertilizer in a wheat-camelina crop rotation cycle. We find that the combined operation is not only able to help boost crop yields, but also to provide added crop yields and associated profits from TGFA (from crop production) for use an ICTL plant feedstock. This program demonstrated the overall viability of ICTL in pilot scale operations. Related work on the Life Cycle Assessment (LCA) of a Montana project indicated that CCU could be employed very effectively to reduce the overall carbon footprint of the MCL/CHI process. Plans are currently being made to conduct larger-scale process demonstration studies of the CHI process in combination with CCU to generate synthetic jet and diesel fuels from algae and algae fertilized crops. Site assessment and project prefeasibility studies are planned with a major EPC firm to determine the overall viability of ICTL technology commercialization with Crow coal resources in south central Montana.« less

Modules for estimating solid waste from fossil-fuel technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crowther, M.A.; Thode, H.C. Jr.; Morris, S.C.

1980-10-01

Solid waste has become a subject of increasing concern to energy industries for several reasons. Increasingly stringent air and water pollution regulations result in a larger fraction of residuals in the form of solid wastes. Control technologies, particularly flue gas desulfurization, can multiply the amount of waste. With the renewed emphasis on coal utilization and the likelihood of oil shale development, increased amounts of solid waste will be produced. In the past, solid waste residuals used for environmental assessment have tended only to include total quantities generated. To look at environmental impacts, however, data on the composition of the solidmore » wastes are required. Computer modules for calculating the quantities and composition of solid waste from major fossil fuel technologies were therefore developed and are described in this report. Six modules have been produced covering physical coal cleaning, conventional coal combustion with flue gas desulfurization, atmospheric fluidized-bed combustion, coal gasification using the Lurgi process, coal liquefaction using the SRC-II process, and oil shale retorting. Total quantities of each solid waste stream are computed together with the major components and a number of trace elements and radionuclides.« less

Deashing of coal liquids with ceramic membrane microfiltration and diafiltration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bishop, B.; Goldsmith, R.

1995-12-31

Removal of mineral matter from liquid hydrocarbons derived from the direct liquefaction of coal is required for product acceptability. Current methods include critical solvent deashing (Rose{sup {reg_sign}} process from Kerr-McGee) and filtration (U.S. Filter leaf filter as used by British Coal). These methods produce ash reject streams containing up to 15% of the liquid hydrocarbon product. Consequently, CeraMem proposed the use of low cost, ceramic crossflow membranes for the filtration of coal liquids bottoms to remove mineral matter and subsequent diafiltration (analogous to cake washing in dead-ended filtration) for the removal of coal liquid from the solids stream. The usemore » of these ceramic crossflow membranes overcomes the limitations of traditional polymeric crossflow membranes by having the ability to operate at elevated temperature and to withstand prolonged exposure to hydrocarbon and solvent media. In addition, CeraMem`s membrane filters are significantly less expensive than competitive ceramic membranes due to their unique construction. With these ceramic membrane filters, it may be possible to reduce the product losses associated with traditional deashing processes at an economically attractive cost. The performance of these ceramic membrane microfilters is discussed.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Starling, K.E.; Lee, L.L.; Ellington, R.T.

The objectives of this project are to: (1) develop transport property correlations for nonpolar, polar, and associating coal fluids using the same characterization parameters as those for a multiparameter corresponding-stages thermodynamic correlation for nonpolar, polar, and associating coal fluids. The same characterization parameters are needed to facilitate the next task; (2) develop methods of estimating correlation characterization parameters, such as critical constants, for distillable and nondistillable coal fluids. In the method to be developed, characterization parameters are determined by multiproperty analysis of normal boiling point, specific gravity, viscosity, and other thermophysical properties that can be measured on undefined coal-fluid fractionsmore » that have been fractionated by distillation, supercritical distillation (destraction), or other separation and compositional analysis techniques. In order to carry out this method of characterization, the thermodynamic- and transport-property correlations have to be developed using the same characterization parameters; (3) test the characterization method for nondistillable residuum to the extent that measurements of residuum specific gravities, viscosities, and other inspection data are available through the destraction method; and (4) apply the correlations and characterization method to current industry problems in coal liquefaction, such as those encountered at the Wilsonville Advanced Coal Liquefaction (ACL) facility. In the first quarter, pertinent viscosity and thermal conductivity data for pure fluids and mixtures were collected and entered into our data bank. The data collected thus far and the references from which the data were taken are summarized in Appendices. 65 references.« less

Data on development of new energy technologies

NASA Astrophysics Data System (ADS)

1994-03-01

The paper compiles data on the trend of development of new energy technologies into a book. By category, renewable energy is solar energy, wind power generation, geothermal power generation, ocean energy, and biomass. As a category of fuel form conversion, cited are coal liquefaction/gasification, coal gasification combined cycle power generation, and natural gas liquefaction/decarbonization. The other categories are cogeneration by fuel cell and ceramic gas turbine, district heat supply system, power load leveling technology, transportation-use substitution-fuel vehicle, and others (Stirling engine, superconducting power generator, etc.). The data are systematically compiled on essential principles, transition of introduction, objectives of introduction, status of production, cost, development schedule, performance, etc. The paper also deals with the related legislation system, developmental organizations, and a menu for power companies' buying surplus power.

Power recovery system for coal liquefaction process

DOEpatents

Horton, J.R.; Eissenberg, D.M.

A flow work exchanger for use in feeding a reactant material to a high-pressure reactor vessel comprises an outer shell, an inner shell concentrically disposed within said outer shell, means for conducting said reactant into the lower end of said lower shell and thence to said reactor vessel, and means for conducting a hotter product effluent from said reactor vessel into the upper end of said inner shell and out of the annulus between said inner and outer shells.

Power recovery system for coal liquefaction process

DOEpatents

Horton, Joel R.; Eissenberg, David M.

1985-01-01

A flow work exchanger for use in feeding a reactant material to a high-pressure reactor vessel comprises an outer shell, an inner shell concentrically disposed within said outer shell, means for conducting said reactant into the lower end of said lower shell and then to said reactor vessel, and means for conducting a hotter product effluent from said reactor vessel into the upper end of said inner shell and out of the annulus between said inner and outer shells.

Alternative fossil-based transportation fuels

DOT National Transportation Integrated Search

2008-01-01

"Alternative fuels derived from oil sands and from coal liquefaction can cost-effectively diversify fuel supplies, but neither type significantly reduces U.S. carbon-dioxide emissions enough to arrest long-term climate change".

Roles of molecular hydrogen and a hydrogen donor solvent in the cracking of moal model compounds with dispersed catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suzuki, Toshimitsu; Ikenaga, Na-oki; Sakota, Takahiro

1994-12-31

It is of great importance to evaluate quantitative hydrogen transfer process by using coal model compounds with a hydrogen-donor solvent. Cronauer el al. showed that in the cracking of benzyl phenyl ether the hydrogen required to stabilize free radicals comes from a donor solvent or intramolecular rearrangement and not from gaseous hydrogen in the absence of a catalyst. Korobkov et al. and Schlosberg et al. showed that the thermolysis of benzyl phenyl ether and dibenzyl ether were accomplished by intramolecular rearrangements. Yokokawa et al. reported that tetralin retarded the catalyzed hydrocracking of coal model compounds containing C-C and C-O bonds.more » However, few studies dealt with quantitative discussion in the hydrogen transfer process from a hydrogen-donor solvent or molecular hydrogen to free radicals derived from a model compound except a series of studies by Nicole and co-workers. On the other hand, it is well known that the amount of naphthalene produced from tetralin decreases after the liquefaction of coal in tetralin with catalyst as compared to the liquefaction in the absence of catalysts. To account for this, two mechanisms are proposed. One is that the catalyst hydrogenates naphthalene produced from tetralin, and the other is that the catalyst promotes the direct hydrogen transfer from molecular hydrogen to free radicals. The purpose of this work is to elucidate the role of catalyst and tetralin by means of the quantitative treatment of the hydrogen transfer reaction stabilizing thermally decomposed free radicals. Cracking of benzyl phenyl ether (BPE), dibenzyl ether (DBE), 1,2-diphenylethane, and 1,3-diphenylpropane was studied in tetralin in the presence of highly disposed catalyst.« less

Health effects research in direct coal liquefaction. Studies of H-coal distillates: Phase I. PDU samples - the effects of hydrotreatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Epler, J.L.; Fry, R.J.M.; Larimer, F.W.

1981-11-01

A multi-divisional effort aimed at the integrated assessment of the health and environmental effects of various coal conversion and shale oil technologies is being carried out. The feasibility of using health effects bioassays to predict the potential biohazard of various H-Coal derived test materials is examined in a coupled chemical and biological approach. The primary focus of the research is the use of preliminary chemical characterizations and preparation for bioassay, followed by testing in short-term assays in order to rapidly ascertain the potential biohazard. Mammalian toxicological assays parallel the testing. Raw and hydrotreated product liquids from process development units ofmore » H-Coal and the pilot plant solvent refined coal process were examined for acute toxicity monitored as population growth impairment of Tetrahymena exposed to aqueous extracts and for mutagenic activity monitored as revertants of Salmonella exposed to metabolically activated chemical class fractions. Medium to high severity hydrotreatment appears to be an effective means of reducing biological activity, presumably by reducing the aromaticity and heteroatom content. Five basic mammalian, acute toxicity tests have been conducted with selected H-coal samples and shale oil derivatives. The data show that H-Coal samples are moderately toxic whereas the toxicity of shale oil derived products is slight and comparable to samples obtained from naturally occurring petroleums. No overt skin or eye toxicity was found. The present data reveal that coal-derived distillates generated by the H-coal process are highly carcinogenic to mouse skin. An extreme form of neurotoxicity associated with dermal exposure to one of the lighter, minimally carcinogenic, materials was noted. (DMC)« less

Erosion-resistant composite material

DOEpatents

Finch, C.B.; Tennery, V.J.; Curlee, R.M.

A highly erosion-resistant composite material is formed of chemical vapor-deposited titanium diboride on a sintered titanium diboride-nickel substrate. This material may be suitable for use in cutting tools, coal liquefaction systems, etc.

Experimental evaluation of coal conversion solid waste residuals. Progress report, August 1-October 31, 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neufeld, R. D.; Bern, J.; Erdogan, H.

1979-11-15

Activities are underway to investigate basic phenomena that would assist demonstration and commercial sized coal conversion facilities in the environmentally acceptable disposal of process solid waste residuals. The approach taken is to consider only those residuals coming from the conversion technology itself, i.e. from gasification, liquefaction, and hot-clean-up steps as well as residuals from the wastewater treatment train. Residuals from the coal mining and coal grinding steps will not be considered in detail since those materials are being handled in some manner in the private sector. Laboratory evalations have been conducted on solid waste samples of fly ash from anmore » existing Capman gasifier. ASTM-A and EPA-EP leaching procedures have been completed on sieved size fractions of the above wastes. Data indicate that smaller size fractions pose greater contamination potential than do larger size particles with a transition zone occurring at particle sizes of about 0.05 inches in diameter. Ames testing of such residuals is reported. Similar studies are under way with samples of H-Coal solid waste residuals.« less

Resource and energy management of synfuels production with hydrogen and oxygen requirements from electrolysis

NASA Astrophysics Data System (ADS)

Shannon, R. H.; Richardson, R. D.

The Resource and Energy Management System (REM), which uses electrolytic H2 and O2 to produce synthetic crude and light oils from heavy hydrocarbons is described. The heavy hydrocarbon feedstocks include heavy oils, tar sand bitumens, heavy residual oils, oil shale kerogens, liquefied coal, and pyrolytically-extracted coal liquids. The system includes mini-upgraders, which can be implemented in modular form, to pump electrolytically-derived H2 into heavy oils to upgrade their energy content. Projected costs for the production of synthetic light oils using U.S. coal reserves with the REM process after liquefaction are $30-35/bbl, with the H2 costs being a controlling factor. The modular systems could be built in a much shorter time frame than much larger projects, and would be instrumental in establishing the electrolytic H2 production infrastructure needed for eventual full conversion to an H2-based economy.

Chemical Compositional Analysis of Catalytic Hydroconversion Products of Heishan Coal Liquefaction Residue

PubMed Central

Wu, Yajun; Zhang, Shuangquan; Yang, Xiaoqin; Wei, Xianyong

2017-01-01

Liquefaction residue of Heishan bituminous coal (HLR) was subject to two hydroconversion reactions under 5 MPa initial pressure of hydrogen at 300°C for 3 h, without catalyst and with acid supported catalyst (ASC), respectively. The reaction products were analyzed with gas chromatography/mass spectrometer (GC/MS). The results show that 222 organic compounds were detected totally in the products and they can be divided into alkanes, aromatic hydrocarbons (AHCs), phenols, ketones, ethers, and other species (OSs). The yield of hydroconversion over the ASC is much higher than that without catalyst. The most abundant products are aromatic hydrocarbons in the reaction products from both catalytic and noncatalytic reactions of HLR. The yield of aromatic hydrocarbons in the reaction product from hydroconversion with the ACS is considerably higher than that from hydroconversion without a catalyst. PMID:28250770

The Navy Biofuel Initiative Under the Defense Production Act

DTIC Science & Technology

2012-06-22

Market for Biomass -Based Diesel Fuel in the Renewable Fuel Standard (RFS), by Brent D. Yacobucci, The Market for Biomass -Based Diesel Fuel in the...defense.17 During the 1970s, DOE directed a synthetic fuels program toward commercializing coal liquefaction, coal gasification , and oil shale... Biomass : Background and Policy, by Anthony Andrews and Jeffrey Logan. The Navy Biofuel Initiative Under the Defense Production Act Congressional

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fishkind, H.H.

The overall environmental impact of the eucalyptus to methanol energy system in Florida is assessed. The environmental impacts associated with the following steps of the process are considered: (1) the greenhouse and laboratory; (2) the eucalyptus plantation; (3) transporting the mature logs; (4) the hammermill; and (5) the methanol synthesis plant. Next, the environmental effects of methanol as an undiluted motor fuel, methanol as a gasoline blend, and gasoline as motor fuels are compared. Finally, the environmental effects of the eucalypt gasification/methanol synthesis system are compared to the coal liquefaction and conversion system.

Solvent refined coal (SRC) process. Annual technical progress report, January 1979-December 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-11-01

A set of statistically designed experiments was used to study the effects of several important operating variables on coal liquefaction product yield structures. These studies used a Continuous Stirred-Tank Reactor to provide a hydrodynamically well-defined system from which kinetic data could be extracted. An analysis of the data shows that product yield structures can be adequately represented by a correlative model. It was shown that second-order effects (interaction and squared terms) are necessary to provide a good model fit of the data throughout the range studied. Three reports were issued covering the SRC-II database and yields as functions of operatingmore » variables. The results agree well with the generally-held concepts of the SRC reaction process, i.e., liquid phase hydrogenolysis of liquid coal which is time-dependent, thermally activated, catalyzed by recycle ash, and reaction rate-controlled. Four reports were issued summarizing the comprehensive SRC reactor thermal response models and reporting the results of several studies made with the models. Analytical equipment for measuring SRC off-gas composition and simulated distillation of coal liquids and appropriate procedures have been established.« less

Control technology assessment for coal gasification and liquefaction processes, coal gasification facility, Caterpillar Tractor Company, York, Pennsylvania. Report for the site visit of May 1981. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Telesca, D.R.

A control technology survey was conducted at the coal gasification facility of the Caterpillar Tractor Company (SIC-5161), in York, Pennsylvania on August 18, 1980 and May 7, 1981, in conjunction with an industrial hygiene characterization study. Potential hazards included coal dust, noise, fire, carbon-monoxide (630080) (CO), polynuclear aromatics, hydrogen sulfide (7783064), phenols, and flammable and explosive gases. Preemployment physicals were given to employees including complete medical histories, physical examinations, and skin examination. Examinations were given annually for the first 5 years and semiannually thereafter. The most hazardous activities were poking, cleaning, inspection of process equipment, and equipment maintenance. Coal dustmore » emissions were effectively reduced by enclosure and venting. Venturi steam injectors in the gasifier pokeholes prevented gas emissions during poking. Ash dust was controlled by removal and handling while it was wet. An audible and visual alarm was used for CO monitoring. The ventilation system in the building effectively prevented accumulation of gases. The author recommends separate lockers for contaminated and clean clothing; a clean area for eating; escape pack respirators located in the rectifier room, control room, and coal bunker; and supplied air respirators in dangerous areas. Disposal of off gas from the feeding system should be addressed.« less

Unconventional Coal in Wyoming: IGCC and Gasification of Direct Coal Liquefaction Residue

NASA Astrophysics Data System (ADS)

Schaffers, William Clemens

Two unconventional uses for Wyoming Powder River Basin coal were investigated in this study. The first was the use of coal fired integrated gasification combined cycle (IGCC) plants to generate electricity. Twenty-eight different scenarios were modeled using AspenPlusRTM software. These included slurry, mechanical and dried fed gasifiers; Wyodak and Green River coals, 0%, 70%, and 90% CO2 capture; and conventional evaporative vs air cooling. All of the models were constructed on a feed basis of 6,900 tons of coal per day on an "as received basis". The AspenPlus RTM results were then used to create economic models using Microsoft RTM Excel for each configuration. These models assumed a 3 year construction period and a 30 year plant life. Results for capital and operating costs, yearly income, and internal rates of return (IRR) were compared. In addition, the scenarios were evaluated to compare electricity sales prices required to obtain a 12% IRR and to determine the effects of a carbon emissions tax on the sales price. The second part of the study investigated the gasification potential of residue remaining from solvent extraction or liquefaction of Powder River Basin Coal. Coal samples from the Decker mine on the Wyoming-Montana border were extracted with tetralin at a temperature of 360°C and pressure of 250 psi. Residue from the extraction was gasified with CO2 or steam at 833°C, 900°C and 975°C at pressures of 0.1 and 0.4 MPa. Product gases were analyzed with a mass spectrometer. Results were used to determine activation energies, reaction order, reaction rates and diffusion effects. Surface area and electron microscopic analyses were also performed on char produced from the solvent extraction residue.

Controlled short residence time coal liquefaction process

DOEpatents

Anderson, Raymond P.; Schmalzer, David K.; Wright, Charles H.

1982-05-04

Normally solid dissolved coal product and a distillate liquid product are produced by continuously passing a feed slurry comprising raw feed coal and a recycle solvent oil and/or slurry together with hydrogen to a preheating-reaction zone (26, alone, or 26 together with 42), the hydrogen pressure in the preheating-reaction zone being at least 1500 psig (105 kg/cm.sup.2), reacting the slurry in the preheating-reaction zone (26, or 26 with 42) at a temperature in the range of between about 455.degree. and about 500.degree. C. to dissolve the coal to form normally liquid coal and normally solid dissolved coal. A total slurry residence time is maintained in the reaction zone ranging from a finite value from about 0 to about 0.2 hour, and reaction effluent is continuously and directly contacted with a quenching fluid (40, 68) to substantially immediately reduce the temperature of the reaction effluent to below 425.degree. C. to substantially inhibit polymerization so that the yield of insoluble organic matter comprises less than 9 weight percent of said feed coal on a moisture-free basis. The reaction is performed under conditions of temperature, hydrogen pressure and residence time such that the quantity of distillate liquid boiling within the range C.sub.5 -455.degree. C. is an amount at least equal to that obtainable by performing the process under the same conditions except for a longer total slurry residence time, e.g., 0.3 hour. Solvent boiling range liquid is separated from the reaction effluent and recycled as process solvent.

Short residence time coal liquefaction process including catalytic hydrogenation

DOEpatents

Anderson, R.P.; Schmalzer, D.K.; Wright, C.H.

1982-05-18

Normally solid dissolved coal product and a distillate liquid product are produced by continuously passing a feed slurry comprising raw feed coal and a recycle solvent oil and/or slurry together with hydrogen to a preheating-reaction zone, the hydrogen pressure in the preheating-reaction zone being at least 1,500 psig (105 kg/cm[sup 2]), reacting the slurry in the preheating-reaction zone at a temperature in the range of between about 455 and about 500 C to dissolve the coal to form normally liquid coal and normally solid dissolved coal. A total slurry residence time is maintained in the reaction zone ranging from a finite value from about 0 to about 0.2 hour, and reaction effluent is continuously and directly contacted with a quenching fluid to substantially immediately reduce the temperature of the reaction effluent to below 425 C to substantially inhibit polymerization so that the yield of insoluble organic matter comprises less than 9 weight percent of said feed coal on a moisture-free basis. The reaction is performed under conditions of temperature, hydrogen pressure and residence time such that the quantity of distillate liquid boiling within the range C[sub 5]-454 C is an amount at least equal to that obtainable by performing the process under the same condition except for a longer total slurry residence time, e.g., 0.3 hour. Solvent boiling range liquid is separated from the reaction effluent and recycled as process solvent. The amount of solvent boiling range liquid is sufficient to provide at least 80 weight percent of that required to maintain the process in overall solvent balance. 6 figs.

Short residence time coal liquefaction process including catalytic hydrogenation

DOEpatents

Anderson, Raymond P.; Schmalzer, David K.; Wright, Charles H.

1982-05-18

Normally solid dissolved coal product and a distillate liquid product are produced by continuously passing a feed slurry comprising raw feed coal and a recycle solvent oil and/or slurry together with hydrogen to a preheating-reaction zone (26, alone, or 26 together with 42), the hydrogen pressure in the preheating-reaction zone being at least 1500 psig (105 kg/cm.sup.2), reacting the slurry in the preheating-reaction zone (26, or 26 with 42) at a temperature in the range of between about 455.degree. and about 500.degree. C. to dissolve the coal to form normally liquid coal and normally solid dissolved coal. A total slurry residence time is maintained in the reaction zone ranging from a finite value from about 0 to about 0.2 hour, and reaction effluent is continuously and directly contacted with a quenching fluid (40, 68) to substantially immediately reduce the temperature of the reaction effluent to below 425.degree. C. to substantially inhibit polymerization so that the yield of insoluble organic matter comprises less than 9 weight percent of said feed coal on a moisture-free basis. The reaction is performed under conditions of temperature, hydrogen pressure and residence time such that the quantity of distillate liquid boiling within the range C.sub.5 -454.degree. C. is an amount at least equal to that obtainable by performing the process under the same condition except for a longer total slurry residence time, e.g., 0.3 hour. Solvent boiling range liquid is separated from the reaction effluent (83) and recycled as process solvent (16). The amount of solvent boiling range liquid is sufficient to provide at least 80 weight percent of that required to maintain the process in overall solvent balance.

Pressure-Letdown Machine for a Coal Reactor

NASA Technical Reports Server (NTRS)

Perkins, G. S.; Mabe, W. B.

1986-01-01

Pumps operating in reverse generate power. Conceptual pressure-letdown machine for coal-liquefaction system extracts energy from expansion of product fluid. Mud pumps, originally intended for use in oil drilling, operated in reverse so their motors act as generators. Several pumps operated in alternating phase to obtain multiple stages of letdown from inlet pressure to outlet pressure. About 75 percent of work generates inlet pressure recoverable as electrical energy.

CO.sub.2 Pretreatment prevents calcium carbonate formation

DOEpatents

Neavel, Richard C.; Brunson, Roy J.; Chaback, Joseph J.

1980-01-01

Scale formation during the liquefaction of lower ranking coals and similar carbonaceous materials is significantly reduced and/or prevented by pretreatment with carbon dioxide. The carbon dioxide pretreatment is believed to convert the scale-forming components to the corresponding carbonate prior to liquefaction. The pretreatment is accomplished at a total pressure within the range from about 14 to about 68 atmospheres and a carbon dioxide partial pressure within the range from about 14 to about 34 atmospheres. Temperature during pretreatment will generally be within the range from about 100.degree. to about 200.degree. C.

An investigation of the role of water on retrograde/condensation reactions and enhanced liquefaction yields. Quarterly progress report, January 1, 1994--March 31, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miknis, F.P.; Netzel, D.A.

The results of coal swelling measurements using 1,4-dioxane as the swelling reagent for premoisturized coals (raw) and coal dried thermally, chemically, and with microwave radiation are presented. An increase in the swelling ratio relative to raw coal indicates a decrease in the amount of cross-linking in the coal. Conversely, a decrease in the ratio indicates an increase in cross-linking. The extent of cross-linking (as measured by 1,4-dioxane) for Texas, Black Thunder, and Eagle Butte Coals are about the same. Illinois {number_sign}6 coal appears to have less cross-linking relative to the other three coals. These results are expected on the basismore » of coal rank. The increase in cross linking is most pronounced for coals dried thermally and with microwave radiation. A decrease in the swelling ratios for all four coals suggests that cross-linking had occurred possibly due to partial devolatilization process. However, low temperature, chemical dehydration of the coals causes only a small or no change in the internal structure for Texas and Illinois {number_sign}6 coals whereas a significant decrease in the cross-linking structure for the Black Thunder and Eagle Butte coals is observed. It is possible that the solvent (CH{sub 3}OH) and products resulting from the chemical dehydrating (acetone and methanol) occupy the surface sites that water had before the reaction and thus preventing cross-linking to occur. These reagents can also promote swelling of coals and may account for some of the decrease in the cross-linking of the coal structure observed for the chemically dried coals.« less

Coal: the new black

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tullo, A.H.; Tremblay, J.-F.

2008-03-15

Long eclipsed by oil and natural gas as a raw material for high-volume chemicals, coal is making a comeback, with oil priced at more than $100 per barrel. It is relatively cheap feedstock for chemicals such as methanol and China is building plants to convert coal to polyolefins on a large scale and interest is spreading worldwide. Over the years several companies in the US and China have made fertilizers via the gasification of coal. Eastman in Tennessee gasifies coal to make methanol which is then converted to acetic acid, acetic anhydride and acetate fiber. The future vision is tomore » convert methanol to olefins. UOP and Lurgi are the major vendors of this technology. These companies are the respective chemical engineering arms of Honeywell and Air Liquide. The article reports developments in China, USA and India on coal-to-chemicals via coal gasification or coal liquefaction. 2 figs., 2 photo.« less

A novel vortex tube-based N2-expander liquefaction process for enhancing the energy efficiency of natural gas liquefaction

NASA Astrophysics Data System (ADS)

Qyyum, Muhammad Abdul; Wei, Feng; Hussain, Arif; Ali, Wahid; Sehee, Oh; Lee, Moonyong

2017-11-01

This research work unfolds a simple, safe, and environment-friendly energy efficient novel vortex tube-based natural gas liquefaction process (LNG). A vortex tube was introduced to the popular N2-expander liquefaction process to enhance the liquefaction efficiency. The process structure and condition were modified and optimized to take a potential advantage of the vortex tube on the natural gas liquefaction cycle. Two commercial simulators ANSYS® and Aspen HYSYS® were used to investigate the application of vortex tube in the refrigeration cycle of LNG process. The Computational fluid dynamics (CFD) model was used to simulate the vortex tube with nitrogen (N2) as a working fluid. Subsequently, the results of the CFD model were embedded in the Aspen HYSYS® to validate the proposed LNG liquefaction process. The proposed natural gas liquefaction process was optimized using the knowledge-based optimization (KBO) approach. The overall energy consumption was chosen as an objective function for optimization. The performance of the proposed liquefaction process was compared with the conventional N2-expander liquefaction process. The vortex tube-based LNG process showed a significant improvement of energy efficiency by 20% in comparison with the conventional N2-expander liquefaction process. This high energy efficiency was mainly due to the isentropic expansion of the vortex tube. It turned out that the high energy efficiency of vortex tube-based process is totally dependent on the refrigerant cold fraction, operating conditions as well as refrigerant cycle configurations.

Pretreatment of solid carbonaceous material with dicarboxylic aromatic acids to prevent scale formation

DOEpatents

Brunson, Roy J.

1982-01-01

Scale formation during the liquefaction of lower ranking coals and similar carbonaceous materials is significantly reduced and/or prevented by pretreatment with a pretreating agent selected from the group consisting of phthalic acid, phthalic anhydride, pyromellitic acid and pyromellitic anhydride. The pretreatment is believed to convert the scale-forming components to the corresponding phthalate and/or pyromellitate prior to liquefaction. The pretreatment is accomplished at a total pressure within the range from about 1 to about 2 atmospheres. Temperature during pretreatment will generally be within the range from about 5.degree. to about 80.degree. C.

Process for heating coal-oil slurries

DOEpatents

Braunlin, W.A.; Gorski, A.; Jaehnig, L.J.; Moskal, C.J.; Naylor, J.D.; Parimi, K.; Ward, J.V.

1984-01-03

Controlling gas to slurry volume ratio to achieve a gas holdup of about 0.4 when heating a flowing coal-oil slurry and a hydrogen containing gas stream allows operation with virtually any coal to solvent ratio and permits operation with efficient heat transfer and satisfactory pressure drops. The critical minimum gas flow rate for any given coal-oil slurry will depend on numerous factors such as coal concentration, coal particle size distribution, composition of the solvent (including recycle slurries), and type of coal. Further system efficiency can be achieved by operating with multiple heating zones to provide a high heat flux when the apparent viscosity of the gas saturated slurry is highest. Operation with gas flow rates below the critical minimum results in system instability indicated by temperature excursions in the fluid and at the tube wall, by a rapid increase and then decrease in overall pressure drop with decreasing gas flow rate, and by increased temperature differences between the temperature of the bulk fluid and the tube wall. At the temperatures and pressures used in coal liquefaction preheaters the coal-oil slurry and hydrogen containing gas stream behaves essentially as a Newtonian fluid at shear rates in excess of 150 sec[sup [minus]1]. The gas to slurry volume ratio should also be controlled to assure that the flow regime does not shift from homogeneous flow to non-homogeneous flow. Stable operations have been observed with a maximum gas holdup as high as 0.72. 29 figs.

Process for heating coal-oil slurries

DOEpatents

Braunlin, Walter A.; Gorski, Alan; Jaehnig, Leo J.; Moskal, Clifford J.; Naylor, Joseph D.; Parimi, Krishnia; Ward, John V.

1984-01-03

Controlling gas to slurry volume ratio to achieve a gas holdup of about 0.4 when heating a flowing coal-oil slurry and a hydrogen containing gas stream allows operation with virtually any coal to solvent ratio and permits operation with efficient heat transfer and satisfactory pressure drops. The critical minimum gas flow rate for any given coal-oil slurry will depend on numerous factors such as coal concentration, coal particle size distribution, composition of the solvent (including recycle slurries), and type of coal. Further system efficiency can be achieved by operating with multiple heating zones to provide a high heat flux when the apparent viscosity of the gas saturated slurry is highest. Operation with gas flow rates below the critical minimum results in system instability indicated by temperature excursions in the fluid and at the tube wall, by a rapid increase and then decrease in overall pressure drop with decreasing gas flow rate, and by increased temperature differences between the temperature of the bulk fluid and the tube wall. At the temperatures and pressures used in coal liquefaction preheaters the coal-oil slurry and hydrogen containing gas stream behaves essentially as a Newtonian fluid at shear rates in excess of 150 sec.sup. -1. The gas to slurry volume ratio should also be controlled to assure that the flow regime does not shift from homogeneous flow to non-homogeneous flow. Stable operations have been observed with a maximum gas holdup as high as 0.72.

Advanced direct coal liquefaction concepts. Quarterly report, January 1, 1993--March 31, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berger, D.J.; Parker, R.J.; Simpson, P.L.

1993-07-01

Five barrels of a Wilsonville process derived solvent (V-1074) from Black Thunder coal were obtained. This material boils within the preferred gas oil range, is more aromatic than previous solvents, and will therefore be used for the bench unit studies. Several repeat runs were performed in the autoclave to confirm the results of the matrix study. In addition, runs were carried out with different catalysts, with agglomerates and with the V-1074 solvent. The results of the autoclave runs were analyzed with respect to coal conversion, CO conversion, oil yield, hydrogen consumption and oxygen removal. It was concluded that the bestmore » operating conditions for the first stage operation was a temperature of at least 390{degrees}C, residence time of at least 30 minutes, cold CO pressure of at least 600 psig and potassium carbonate catalyst (2% wt on total feed). The data also indicated however, that the coal conversion goes through a maximum, and too high a severity leads to retrograde reaction and lower coal solubilization. The scope for increasing temperature and time is therefore limited. Petrographic examination of the THF insoluble resids from the autoclave program indicated a maximum coal conversion of about 90% for Black Thunder coal. The bench unit construction was also essentially completed and the bench unit program to be carded out in the next twelve months was defined.« less

Low-rank coal study: national needs for resource development. Volume 3. Technology evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-11-01

Technologies applicable to the development and use of low-rank coals are analyzed in order to identify specific needs for research, development, and demonstration (RD and D). Major sections of the report address the following technologies: extraction; transportation; preparation, handling and storage; conventional combustion and environmental control technology; gasification; liquefaction; and pyrolysis. Each of these sections contains an introduction and summary of the key issues with regard to subbituminous coal and lignite; description of all relevant technology, both existing and under development; a description of related environmental control technology; an evaluation of the effects of low-rank coal properties on the technology;more » and summaries of current commercial status of the technology and/or current RD and D projects relevant to low-rank coals.« less

Reverse micelle synthesis of nanoscale metal containing catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Darab, J.G.; Fulton, J.L.; Linehan, J.C.

1993-03-01

The need for morphological control during the synthesis of catalyst precursor powders is generally accepted to be important. In the liquefaction of coal, for example, iron-bearing catalyst precursor particles containing individual crystallites with diameters in the 1-100 nanometer range are believed to achieve good dispersion through out the coal-solvent slurry during liquefaction 2 runs and to undergo chemical transformations to catalytically active iron sulfide phases. The production of the nanoscale powders described here employs the confining spherical microdomains comprising the aqueous phase of a modified reverse micelle (MRM) microemulsion system as nanoscale reaction vessels in which polymerization, electrochemical reduction andmore » precipitation of solvated salts can occur. The goal is to take advantage of the confining nature of micelles to kinetically hinder transformation processes which readily occur in bulk aqueous solution in order to control the morphology and phase of the resulting powder. We have prepared a variety of metal, alloy, and metal- and mixed metal-oxide nanoscale powders from appropriate MRM systems. Examples of nanoscale powders produced include Co, Mo-Co, Ni{sub 3}Fe, Ni, and various oxides and oxyhydroxides of iron. Here, we discuss the preparation and characterization of nickel metal (with a nickel oxide surface layer) and iron oxyhydroxide MRM nanoscale powders. We have used extended x-ray absorption fine structure (EXAFS) spectroscopy to study the chemical polymerization process in situ, x-ray diffraction (XRD), scanning and transmission electron microcroscopies (SEM and TEM), elemental analysis and structural modelling to characterize the nanoscale powders produced. The catalytic activity of these powders is currently being studied.« less

George Andrew Olah - Patents

Science.gov Websites

Additional Information US 4,394,247 LIQUEFACTION OF COALS USING RECYCLABLE SUPERACID CATALYST - Olah, George catalytic condensation using superacid catalysts. US 4,465,893 OXIDATIVE CONDENSATION OF NATURAL GAS OR ., synthetic transportation fuels or lower olefins) via catalytic condensation using superacid catalysts. US

Studies of coupled chemical and catalytic coal conversion methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stock, L.M.

1988-01-01

Liquefaction of coal by depolymerization in an organic solvent has been studied for several years. The liquefied coal extract which results from such a process is far more suitable for conversion into liquid fuel by hydrogenolysis than is the untreated coal. Investigations on the chemical structure and the reactive sites of coal can help to select useful reactions for the production of liquids from coal. Sternberg et al. demonstrated that the reductive alkylation method transforms bituminous coal into an enormously soluble substance, irrespective of the mild reaction conditions. The effectiveness of newly introduced alkyl groups for the disruption of intermolecularmore » hydrogen bonds and pi-pi interactions between the aromatic sheets in coal macromolecules has been recognized. It has been reported by Ignasiak et al. that a C-alkylabon reaction using sodium or potassium amide in liquid ammonia can be used to introduce alkyl groups at acidic carbon sites. A method has been developed recently in this laboratory for the solubilization of high rank coals. In the previous reports it was shown that n-butyl lithium and potassium t-butoxide in refluxing heptane produced coal anions which could be alkylated with different alkyl halides. Such alkylated coals were soluble up to 92% in solvents like pyridine. Though the solubilization of coal depended very much on the length of the alkyl group, it also depended very much on the nature of the base used. Strong bases like n-butyl lithium (pKa=42) can cause proton abstraction from aromatic structures, if the more acidic benzylic protons are absent. The utility of this procedure, initially developed and used by Miyake and Stock, has now been tested with the high oxygen containing, low rank Illinois No. 6 and Wyodak coals.« less

Studies of coupled chemical and catalytic coal conversion methods. Fifth quarterly report, October--December 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stock, L.M.

1988-12-31

Liquefaction of coal by depolymerization in an organic solvent has been studied for several years. The liquefied coal extract which results from such a process is far more suitable for conversion into liquid fuel by hydrogenolysis than is the untreated coal. Investigations on the chemical structure and the reactive sites of coal can help to select useful reactions for the production of liquids from coal. Sternberg et al. demonstrated that the reductive alkylation method transforms bituminous coal into an enormously soluble substance, irrespective of the mild reaction conditions. The effectiveness of newly introduced alkyl groups for the disruption of intermolecularmore » hydrogen bonds and pi-pi interactions between the aromatic sheets in coal macromolecules has been recognized. It has been reported by Ignasiak et al. that a C-alkylabon reaction using sodium or potassium amide in liquid ammonia can be used to introduce alkyl groups at acidic carbon sites. A method has been developed recently in this laboratory for the solubilization of high rank coals. In the previous reports it was shown that n-butyl lithium and potassium t-butoxide in refluxing heptane produced coal anions which could be alkylated with different alkyl halides. Such alkylated coals were soluble up to 92% in solvents like pyridine. Though the solubilization of coal depended very much on the length of the alkyl group, it also depended very much on the nature of the base used. Strong bases like n-butyl lithium (pKa=42) can cause proton abstraction from aromatic structures, if the more acidic benzylic protons are absent. The utility of this procedure, initially developed and used by Miyake and Stock, has now been tested with the high oxygen containing, low rank Illinois No. 6 and Wyodak coals.« less

Protective Clothing. Part 1. Arctic and Tropical Environments (A Bibliography with Abstracts)

DTIC Science & Technology

1976-04-01

75/377/2GSB Hydrogen Energy (86) Apr 75 NTIS/PS-75/379/8GSB Desulfurization of Coal and Petroleum (107) Apr 75 Excludes flue gas and other post...Petroleum (107) Apr 75 Excludes flue gas and other post-combustion sulfur con- trol NTIS/PS-75/381/4GSB Coal Gasification and Liquefaction. Vol 1... desulfurization NTIS/PS-75/455/6GSB Sulfur Dioxide Control . Vol 1. 1964-1972 (159) May 75 NTIS/PS-75/456/4GSB Activated Carbon (221) May 75

H-Coal Pilot Plant: letdown-valve experience through Coal Run No. 7 in the H-Coal Pilot Plant, E-3. [Runs 1 thru 7

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bond, N.D.

1982-05-01

This report covers the development of the various letdown valves used for the two-stage high pressure and temperature coal slurry letdown system as used at the H-Coal Pilot Plant. The period covered in this report was from the prestart-up oil circulation through Coal Runs No. 1 - No. 7. The valves covered are the Willis, which was used exclusively from Coal Runs No. 1 - No. 5, the Cameron and the Kieley and Mueller. The LV-202B Kieley and Mueller and LV-204B Cameron valves again showed little valve wear during short Coal Run No. 7, which demonstrates that the full potentialmore » of these valve designs has not been achieved yet. The problem with the Kieley and Mueller plug freezing will be looked at further, with addition of grease ports and a possible new designed plug shaft and stem guide being made for the valve. The Willis valves developed the same body leaks around the bonnet areas that occurred during Coal Run No. 6. This will be looked at before Coal Run No. 8, but no further trim development is planned. To summarize the progress of the LV-202 and LV-204 valves, the Willis was developed to last about 100 hours, which is the expected life for this valve design in our coal liquefaction process; whereas, the Cameron and Kieley and Mueller valves have lasted for days with good results. The Cameron and Kieley and Mueller valves still have not reached their full potential in plant operation, and, along with the new Masoneilan Sasol, Masoneilan Prototype, Hammel Dahl and Paul valves, future progress in Coal Run No. 8 for the high pressure and temperature letdown valves is anticipated.« less

Alternative process schemes for coal conversion. Progress report No. 1, October 1, 1978--January 31, 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sansone, M.J.

1979-02-01

On the basis of simple, first approximation calculations, it has been shown that catalytic gasification and hydrogasification are inherently superior to conventional gasification with respect to carbon utilization and thermal efficiency. However, most processes which are directed toward the production of substitute natural gas (SNG) by direct combination of coal with steam at low temperatures (catalytic processes) or with hydrogen (hydrogasification) will require a step for separation of product SNG from a recycle stream. The success or falure of the process could well depend upon the economics of this separation scheme. The energetics for the separation of mixtures of idealmore » gases has been considered in some detail. Minimum energies for complete separation of representative effluent mixtures have been calculated as well as energies for separation into product and recycle streams. The gas mixtures include binary systems of H/sub 2/ and CH/sub 4/ and ternary mixtures of H/sub 2/, CH/sub 4/, and CO. A brief summary of a number of different real separation schemes has also been included. We have arbitrarily divided these into five categories: liquefaction, absorption, adsorption, chemical, and diffusional methods. These separation methods will be screened and the more promising methods examined in more detail in later reports. Finally, a brief mention of alternative coal conversion processes concludes this report.« less

Coal liquefaction demonstration plant near Morgantown, West Virgina; water assessment report. Summary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-08-21

This assessment report is for public review and comment and was prepared under the provision of Sect. 13(b) of the 1974 Federal Nonnuclear Energy Research and Development Act. It includes only a preliminary assessment of the commercial project as currently planned.

Liquefaction of coal by Polyporus versicolor and Poria monticola. Final report, 1 September 1984-31 August 1986

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cohen, M.S.

1986-01-01

Polyporus versicolor (ATCC 12679), obtained from the American Type Culture Collection, Rockville, MD, has been demonstrated to degrade leonardite, lignite, and subbituminous coals to a black liquid product which is called the bioextract. The process of solubilizing the coal has been termed liquification. Fungi were routinely maintained in both solid Sabouraud maltose agar (6%) and in Sabouraud maltose broth cultures. All cultures were incubated at 30/sup 0/C, 84 to 98% relative humidity, and pH = 5.8. All materials which came into contact with the fungi were sterilized before use. Experimental cultures were incubated as described for stock cultures. Cultures weremore » incubated for approximately 12 days to produce a mature fungal mat across a glass petri dish. Coal pieces (approximately 5 mm/sup 3/) were placed directly on the hyphal mat. Liquified coal (the bioextract) was removed from the top of the mycelium and/or coal pieces and either stored for analyses at 4/sup 0/C or else freeze-dried and stored dessicated at room temperature. The bioextract has been produced in sufficient quantity to permit various methods of analysis including high performance liquid chromatography, UV-visible spectrophotometry, titrimetry, electrophoresis, proton nmr spectroscopy, and calorimetry. The solubility of the bioextract in different solvents has also been determined. 6 refs., 26 figs., 3 tabs.« less

Reverse micelle synthesis of nanoscale metal containing catalysts. [Nickel metal (with a nickel oxide surface layer) and iron oxyhydroxide nanoscale powders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Darab, J.G.; Fulton, J.L.; Linehan, J.C.

1993-03-01

The need for morphological control during the synthesis of catalyst precursor powders is generally accepted to be important. In the liquefaction of coal, for example, iron-bearing catalyst precursor particles containing individual crystallites with diameters in the 1-100 nanometer range are believed to achieve good dispersion through out the coal-solvent slurry during liquefaction 2 runs and to undergo chemical transformations to catalytically active iron sulfide phases. The production of the nanoscale powders described here employs the confining spherical microdomains comprising the aqueous phase of a modified reverse micelle (MRM) microemulsion system as nanoscale reaction vessels in which polymerization, electrochemical reduction andmore » precipitation of solvated salts can occur. The goal is to take advantage of the confining nature of micelles to kinetically hinder transformation processes which readily occur in bulk aqueous solution in order to control the morphology and phase of the resulting powder. We have prepared a variety of metal, alloy, and metal- and mixed metal-oxide nanoscale powders from appropriate MRM systems. Examples of nanoscale powders produced include Co, Mo-Co, Ni[sub 3]Fe, Ni, and various oxides and oxyhydroxides of iron. Here, we discuss the preparation and characterization of nickel metal (with a nickel oxide surface layer) and iron oxyhydroxide MRM nanoscale powders. We have used extended x-ray absorption fine structure (EXAFS) spectroscopy to study the chemical polymerization process in situ, x-ray diffraction (XRD), scanning and transmission electron microcroscopies (SEM and TEM), elemental analysis and structural modelling to characterize the nanoscale powders produced. The catalytic activity of these powders is currently being studied.« less

The petrology of some Indians coals

NASA Astrophysics Data System (ADS)

Daulay, Bukin; Cook, Alan C.

Samples from coal seams from all of the major Indonesian coalfields, were examined using reflected white light and reflected flourescence mode microscopy techniques. The coals are rich in vitrinite and have variable, commonly high, contents of liptinite. Inertinite is rare to sparse, with the exception of a few (typically Neogene) coals. Overall, no major differences in coal type exist bewteen Paleogene and Neogene coals. Most of the coals are low in rank ( vitrinite reflectanceoverlineRvmax, 0.30% to 0.57% ). The Neogene coals are typically much lower in rank than the Paleogene coals, and this tendency is most clearly seen within the Kalimantan occurences ( PaleogeneoverlineRvmax 0.53% to 0.67%; Neogene 0.30% to 0.57% ). In Sumatera at Bukit Asam, contact alteration from intrusions causes a marked rise in overlineRv max from the range 0.30% to 0.53% overlineRv max to semi-anthracite (2.6%). Near the intrusions, very high lateral and vertical rank gradients are present. At Ombilin in central west Sumatera, regional rank is relatively high ( overlineRvmax 0.55% to 0.77% ), and similar effects from contact alteration ( overlineRvmax up to 4.6% ) can again be detected. The coals are suitable for power generation. Grindability characteristics should be generally favourable, but the rank of the coals is typically sufficiently low for spontaneous combusion to be a significant problem. The rank of the coals is generally too low for use as a single component charge in conventional coke ovens. Significant reverses exist of coals that could be added as a minor component to imported strongly coals to decrease the foreign exchange cost of coke. The rank and type indicate that yield characteristics should be good for most liquefaction and gasification processes. The coals, and to a lesser extent associated dispersed organic matter, form important source rocks for some of the major natural oil accumulations in Indonesians sedimentary basins.

Fundamental studies of coal liquefaction. Quarterly report No. 8, July 1, 1993--October 1, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ross, D.S.

In the last report the effects of water, tetralin, and argon were discussed as media during the heating of Illinois No. 6 coal. In studies in which the temperature was ramped from ambient to 460{degrees}C at 30{degrees}C/min particles were observed to shrink in the case of both water and tetralin, and first swell and then collapse back to particles with their starting shapes in the case of argon. The result with tetralin was expected, but that for water was not. Similarly, the results in argon were not in accord with some models of coal pyrolysis which suggest that coals fullymore » liquefy when heated (Solomon, et al.). The work described here includes discussion of additional work with Illinois No. 6 coal with argon and water, and new work with n-undecane as medium.« less

Liquefaction processes and systems and liquefaction process intermediate compositions

DOEpatents

Schmidt, Andrew J.; Hart, Todd R.; Billing, Justin M.; Maupin, Gary D.; Hallen, Richard T.; Anderson, Daniel B.

2014-07-12

Liquefaction processes are provided that can include: providing a biomass slurry solution having a temperature of at least 300.degree. C. at a pressure of at least 2000 psig; cooling the solution to a temperature of less than 150.degree. C.; and depressurizing the solution to release carbon dioxide from the solution and form at least part of a bio-oil foam. Liquefaction processes are also provided that can include: filtering the biomass slurry to remove particulates; and cooling and depressurizing the filtered solution to form the bio-oil foam. Liquefaction systems are provided that can include: a heated biomass slurry reaction zone maintained above 300.degree. C. and at least 2000 psig and in continuous fluid communication with a flash cooling/depressurization zone maintained below 150.degree. C. and between about 125 psig and about atmospheric pressure. Liquefaction systems are also provided that can include a foam/liquid separation system. Liquefaction process intermediate compositions are provided that can include a bio-oil foam phase separated from an aqueous biomass solids solution.

Kinetics of coal conversion to soluble products. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larsen, J.W.

1994-04-12

The objectives of this work are (1) to measure the kinetics of the conversion of coals to soluble products under model liquefaction conditions using GPS techniques to count the number of bonds broken; (2) to analyze these data using kinetic schemes based on the behavior of crosslinked macromolecular networks. The product was Soxhlet extracted with pyridine until the pyridine solution was clear. A gel permeation chromatogram of the pyridine soluble is shown in Figure 2A. The improved mass sensitive detector system requires only about 500 ng to acquire a chromatogram having fairly good S/N ratio. Apparently, no disturbance is causedmore » by the remaining tetralin and naphthalene formed by dehydrogenation of tetralin. These seriously affect the lower molecular weight region when IR or UV detectors are used. It is a notable advantage of the mass sensitive detector that suitable adjustment of the nebulizer and of the evaporator completely suppressed the contribution of solvent to the chromatogram. The molecular weight distribution of liquefaction product appears to be almost unimodal if the small shoulder at the lower elution volume side is neglected.« less

Processing of centrifuged solids from liquefied coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weintraub, M.; Akhtar, S.; Yavorsky, P.M.

The centrifuged residues from coal liquefaction processes present two problems which the Pittsburgh ETC has found to be controllable by thermal processing of the material: the residues contain significant amounts of carbon and oil that should be recovered, and their sticky, malodorous, dough-like nature makes them difficult to handle. This paper reports the results of heat treatments using several types of processing equipment and two different temperature ranges. Pyrolysis in the range of 1,100/sup 0/ to 1,400/sup 0/F yielded 20 to 30 wt % of oil product, depending on the source of the residue and its initial oil content. Lowermore » temperature heating (e.g., 600/sup 0/F) yielded less oil, but did produce a non-sticky friable solid. The percent oil yield was a function of temperature, residence time, and thickness of the layer exposed. A one-eighth inch thick sample became friable in 15 to 30 minutes exposure to 600/sup 0/F, during which time it lost about 13 percent of its weight. The tests included measurements on a steel conveyor belt, which could become the commercial embodiment of this treatment.« less

Progress of fossil fuel science

DOE Office of Scientific and Technical Information (OSTI.GOV)

Demirbas, M.F.

2007-07-01

Coal is the most abundant and widely distributed fossil fuel. More than 45% of the world's electricity is generated from coal, and it is the major fuel for generating electricity worldwide. The known coal reserves in the world are enough for more than 215 years of consumption, while the known oil reserves are only about 39 times of the world's consumption and the known natural gas reserves are about 63 times of the world's consumption level in 1998. In recent years, there have been effective scientific investigations on Turkish fossil fuels, which are considerable focused on coal resources. Coal ismore » a major fossil fuel source for Turkey. Turkish coal consumption has been stable over the past decade and currently accounts for about 24% of the country's total energy consumption. Lignite coal has had the biggest share in total fossil fuel production, at 43%, in Turkey. Turkish researchers may investigate ten broad pathways of coal species upgrading, such as desulfurization and oxydesulfurization, pyrolysis and hydropyrolysis, liquefaction and hydroliquefaction, extraction and supercritical fluid extraction, gasification, oxidation, briquetting, flotation, and structure identification.« less

Liquefaction of oak tree bark with different biomass/phenol mass ratios and utilizing bio-based polyols for carbon foam production

NASA Astrophysics Data System (ADS)

Ozbay, N.; Yargic, A. S.

2017-02-01

Carbon foam is sponge like carbonaceous material with low density, high conductivity and high strength; which is used in various applications such as catalyst supports, membrane separations, high thermally conductive heat sinks, energy absorption materials, high temperature thermal insulation. Coal or fossil oils are conventionally used to fabricate pitch, phenolic resin and polyurethane as carbon foam precursor. Biomass liquefaction is a developing technique to convert biomass resources into the industrial chemicals. In this study, oak tree bark was liquefied under mild conditions with different mass ratio of biomass/phenol; and the liquefaction product was used as polyol to produce porous resin foams. Obtained resin foams were carbonized at 400 °C, and then activated at 800 °C under nitrogen atmosphere. Structure evaluation of resin foams, carbonized foams and activated carbon foams from liquefied oak tree bark was investigated by using elemental analysis, x-ray diffraction, nitrogen adsorption/desorption isotherms, scanning electron microscopy, bulk density and compressive strength tests.

Advanced Hydrogen Liquefaction Process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schwartz, Joseph; Kromer, Brian; Neu, Ben

2011-09-28

The project identified and quantified ways to reduce the cost of hydrogen liquefaction, and reduce the cost of hydrogen distribution. The goal was to reduce the power consumption by 20% and then to reduce the capital cost. Optimizing the process, improving process equipment, and improving ortho-para conversion significantly reduced the power consumption of liquefaction, but by less than 20%. Because the efficiency improvement was less than the target, the program was stopped before the capital cost was addressed. These efficiency improvements could provide a benefit to the public to improve the design of future hydrogen liquefiers. The project increased themore » understanding of hydrogen liquefaction by modeling different processes and thoroughly examining ortho-para separation and conversion. The process modeling provided a benefit to the public because the project incorporated para hydrogen into the process modeling software, so liquefaction processes can be modeled more accurately than using only normal hydrogen. Adding catalyst to the first heat exchanger, a simple method to reduce liquefaction power, was identified, analyzed, and quantified. The demonstrated performance of ortho-para separation is sufficient for at least one identified process concept to show reduced power cost when compared to hydrogen liquefaction processes using conventional ortho-para conversion. The impact of improved ortho-para conversion can be significant because ortho para conversion uses about 20-25% of the total liquefaction power, but performance improvement is necessary to realize a substantial benefit. Most of the energy used in liquefaction is for gas compression. Improvements in hydrogen compression will have a significant impact on overall liquefier efficiency. Improvements to turbines, heat exchangers, and other process equipment will have less impact.« less

Subtask 3.11 - Production of CBTL-Based Jet Fuels from Biomass-Based Feedstocks and Montana Coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, Ramesh

The Energy & Environmental Research Center (EERC), in partnership with the U.S. Department of Energy (DOE) and Accelergy Corporation, an advanced fuels developer with technologies exclusively licensed from Exxon Mobil, undertook Subtask 3.11 to use a recently installed bench-scale direct coal liquefaction (DCL) system capable of converting 45 pounds/hour of pulverized, dried coal to a liquid suitable for upgrading to fuels and/or chemicals. The process involves liquefaction of Rosebud mine coal (Montana coal) coupled with an upgrading scheme to produce a naphthenic fuel. The upgrading comprises catalytic hydrotreating and saturation to produce naphthenic fuel. A synthetic jet fuel was preparedmore » by blending equal volumes of naphthenic fuel with similar aliphatic fuel derived from biomass and 11 volume % of aromatic hydrocarbons. The synthetic fuel was tested using standard ASTM International techniques to determine compliance with JP-8 fuel. The composite fuel thus produced not only meets but exceeds the military aviation fuel-screening criteria. A 500-milliliter synthetic jet fuel sample which met internal screening criteria was submitted to the Air Force Research Laboratory (AFRL) at Wright–Patterson Air Force Base, Dayton, Ohio, for evaluation. The sample was confirmed by AFRL to be in compliance with U.S. Air Force-prescribed alternative aviation fuel initial screening criteria. The results show that this fuel meets or exceeds the key specification parameters for JP-8, a petroleum-based jet fuel widely used by the U.S. military. JP-8 specifications include parameters such as freeze point, density, flash point, and others; all of which were met by the EERC fuel sample. The fuel also exceeds the thermal stability specification of JP-8 fuel as determined by the quartz crystalline microbalance (QCM) test also performed at an independent laboratory as well as AFRL. This means that the EERC fuel looks and acts identically to petroleum-derived jet fuel and can be used interchangeably without any special requirements and thus provides a pathway to energy security to the U.S. military and the entire nation. This subtask was funded through the EERC–DOE Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FC26- 08NT43291. Nonfederal funding was provided by Accelergy Corporation.« less

Liquefaction process for solid carbonaceous materials containing alkaline earth metal humates

DOEpatents

Epperly, William R.; Deane, Barry C.; Brunson, Roy J.

1982-01-01

An improved liquefaction process wherein wall scale and particulate agglomeration during the liquefaction of solid carbonaceous materials containing alkaline earth metal humates is reduced and/or eliminated by subjecting the solid carbonaceous materials to controlled cyclic cavitation during liquefaction. It is important that the solid carbonaceous material be slurried in a suitable solvent or diluent during liquefaction. The cyclic cavitation may be imparted via pressure cycling, cyclic agitation and the like. When pressure cycling or the like is employed an amplitude equivalent to at least 25 psia is required to effectively remove scale from the liquefaction vessel walls.

Developing technologies for synthetic fuels

NASA Astrophysics Data System (ADS)

Sprow, F. B.

1981-05-01

After consideration of a likely timetable for the development of a synthetic fuels industry and its necessary supporting technology, the large variety of such fuels and their potential roles is assessed along with their commercialization outlook. Among the fuel production methods considered are: (1) above-ground retorting of oil shale; (2) in-situ shale retorting; (3) open pit mining of tar sands; (4) in-situ steam stimulation of tar sands; (5) coal gasification; (6) methanol synthesis from carbon monoxide and hydrogen; and (7) direct coal liquefaction by the hydrogenation of coal. It is shown that while the U.S. has very limited resource bases for tar sands and heavy crudes, the abundance of shale in the western states and the abundance and greater geographical dispersion of coal will make these the two most important resources of a future synthetic fuels industry.

Identification and significance of accessory minerals from a bituminous coal

USGS Publications Warehouse

Finkelman, R.B.; Stanton, R.W.

1978-01-01

A scanning electron microscope (SEM) has been used to study the in situ accessory minerals in polished blocks and pellets of petrographically analysed samples of the Waynesburg coal (hvb). Individual grains from the low-temperature ash (LTA) of the same coal were also studied. The visual resolution of the SEM permitted the detection of submicron mineral grains, which could then be analysed by the attached energy-dispersive system. Emphasis was placed on the highly reflective grains in the carbominerite bands. Among the most abundant accessory minerals observed were rutile, zircon, and rare-earth-bearing minerals. Small (1-5 ??m) particles of what may be authigenic iron-rich chromite and a nickel silicate form rims on quartz grains. The SEM also permits the observation of grain morphology and mineral intergrowths. These data are useful in determining authigenicity and diagenic alteration. Substances in density splits of LTA include authigenic, detrital, extraterrestrial magnetite, tourmaline, and evaporite (?) minerals, and a fluorine-bearing amphibole. This analytical approach allows the determination of specific sites for many of the trace elements in coals. In the Waynesburg coal, most of the chromium is in the iron-chromium rims, the fluorine is in the amphibole, and the rare-earth elements are in rare-earth-bearing minerals. The ability to relate trace-element data to specific minerals will aid in predicting the behaviour of elements in coal during combustion, liquefaction, gasification, weathering, and leaching processes. This ability also permits insight into the degree of mobility of these elements in coal and provides clues to sedimentological and diagenetic conditions. ?? 1978.

Leading trends in environmental regulation that affect energy development. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steele, R V; Attaway, L D; Christerson, J A

1980-01-01

Major environmental issues that are likely to affect the implementation of energy technologies between now and the year 2000 are identified and assessed. The energy technologies specifically addressed are: oil recovery and processing; gas recovery and processing; coal liquefaction; coal gasification (surface); in situ coal gasification; direct coal combustion; advanced power systems; magnetohydrodynamics; surface oil shale retorting; true and modified in situ oil shale retorting; geothermal energy; biomass energy conversion; and nuclear power (fission). Environmental analyses of these technologies included, in addition to the main processing steps, the complete fuel cycle from resource extraction to end use. A comprehensive surveymore » of the environmental community (including environmental groups, researchers, and regulatory agencies) was carried out in parallel with an analysis of the technologies to identify important future environmental issues. Each of the final 20 issues selected by the project staff has the following common attributes: consensus of the environmental community that the issue is important; it is a likely candidate for future regulatory action; it deals with a major environmental aspect of energy development. The analyses of the 20 major issues address their environmental problem areas, current regulatory status, and the impact of future regulations. These analyses are followed by a quantitative assessment of the impact on energy costs and nationwide pollutant emissions of possible future regulations. This is accomplished by employing the Strategic Environmental Assessment System (SEAS) for a subset of the 20 major issues. The report concludes with a more general discussion of the impact of environmental regulatory action on energy development.« less

Methods of natural gas liquefaction and natural gas liquefaction plants utilizing multiple and varying gas streams

DOEpatents

Wilding, Bruce M; Turner, Terry D

2014-12-02

A method of natural gas liquefaction may include cooling a gaseous NG process stream to form a liquid NG process stream. The method may further include directing the first tail gas stream out of a plant at a first pressure and directing a second tail gas stream out of the plant at a second pressure. An additional method of natural gas liquefaction may include separating CO.sub.2 from a liquid NG process stream and processing the CO.sub.2 to provide a CO.sub.2 product stream. Another method of natural gas liquefaction may include combining a marginal gaseous NG process stream with a secondary substantially pure NG stream to provide an improved gaseous NG process stream. Additionally, a NG liquefaction plant may include a first tail gas outlet, and at least a second tail gas outlet, the at least a second tail gas outlet separate from the first tail gas outlet.

Method for dispersing catalyst onto particulate material and product thereof

DOEpatents

Utz, Bruce R.; Cugini, Anthony V.

1992-01-01

A method for dispersing finely divided catalyst precursors onto the surface of coal or other particulate material includes the steps of forming a wet paste mixture of the particulate material and a liquid solution containing a dissolved transition metal salt, for instance a solution of ferric nitrate. The wet paste mixture is in a state of incipient wetness with all of this solution adsorbed onto the surfaces of the particulate material without the presence of free moisture. On adding a precipitating agent such as ammonia, a catalyst precursor such as hydrated iron oxide is deposited on the surfaces of the coal. The catalyst is activated by converting it to the sulfide form for the hydrogenation or direct liquefaction of the coal.

Method for dispersing catalyst onto particulate material

DOEpatents

Utz, Bruce R.; Cugini, Anthony V.

1992-01-01

A method for dispersing finely divided catalyst precursors onto the surface of coal or other particulate material includes the steps of forming a wet paste mixture of the particulate material and a liquid solution containing a dissolved transition metal salt, for instance a solution of ferric nitrate. The wet paste mixture is in a state of incipient wetness with all of this solution adsorbed onto the surfaces of the particulate material without the presence of free moisture. On adding a precipitating agent such as ammonia, a catalyst precursor such as hydrated iron oxide is deposited on the surfaces of the coal. The catalyst is activated by converting it to the sulfide form for the hydrogenation or direct liquefaction of the coal.

Direct catalytic hydrothermal liquefaction of spirulina to biofuels with hydrogen

NASA Astrophysics Data System (ADS)

Zeng, Qin; Liao, Hansheng; Zhou, Shiqin; Li, Qiuping; Wang, Lu; Yu, Zhihao; Jing, Li

2018-01-01

We report herein on acquiring biofuels from direct catalytic hydrothermal liquefaction of spirulina. The component of bio-oil from direct catalytic hydrothermal liquefaction was similar to that from two independent processes (including liquefaction and upgrading of biocrude). However, one step process has higher carbon recovery, due to the less loss of carbons. It was demonstrated that the yield and HHV of bio-oil from direct catalytic algae with hydrothermal condition is higher than that from two independent processes.

Plasma electrolytic liquefaction of cellulosic biomass

NASA Astrophysics Data System (ADS)

Dingliang, TANG; Xianhui, ZHANG; Si-ze, YANG

2018-04-01

In this paper, the rapid liquefaction of a corncob was achieved by plasma electrolysis, providing a new method for cellulosic biomass liquefaction. The liquefaction rate of the corncob was 95% after 5 min with polyethylene glycol and glycerol as the liquefying agent. The experiments not only showed that H+ ions catalyzed the liquefaction of the corncob, but also that using accelerated H+ ions, which were accelerated by an electric field, could effectively improve the liquefaction efficiency. There was an obvious discharge phenomenon, in which the generated radicals efficiently heated the solution and liquefied the biomass, in the process of plasma electrolytic liquefaction. Finally, the optimum parameters of the corncob liquefaction were obtained by experimentation, and the liquefaction products were analyzed.

Fundamental studies of coal liquefaction. Quarterly report No. 7, April 1--July 1, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ross, D.S.

1993-07-14

In our last report we discussed observations in our cell concerning the behavior or Illinois No. 6 coal in tetralin to 460{degrees}C. We noted that there were possibly two distinct types of particles comprising the organic phase, reacting respectively at 420{degrees}--430{degrees}C, and at 450{degrees}--460{degrees}C. Alternatively we could interpret the data as describing a range of reactivity bounded by those temperatures. As evidenced by the contraction of the particles, the reactions were rapid. The particles lost half of their substance within 1 min, and we suggested that the rates were too fast to be accommodated by the commonly held scheme formore » coal liquefaction involving thermolytic scission of weak, bibenzyl-like bonds. Our analyses were aided by our use of Adobe Photoshop, which allows us to store, digitized versions of our recorded images. The images can then be manipulated at will to provide quantitative data on morphological changes. We noted in our last report that printer limitations prevented us from presenting images with the desirable quality, and we are at present attempting to find access to equipment which will provide satisfactory figures. Accordingly our progress will be described here without any photographs, and we expect to present a more complete account of our work in our next report. The work reported here includes studies of Illinois No. 6 coal with water as the medium, and a control run with argon as medium. Our temperature ramping was like that used last time, 25{degrees}C/min to 250{degrees}C, and then 10{degrees}C/min to 450{degrees}C. The results from the earlier work and the data presented here can therefore be directly compared.« less

11. Photograph of a line drawing. 'CROSS SECTION OF GAS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. Photograph of a line drawing. 'CROSS SECTION OF GAS PRODUCER.' From George R. Cooper (Wilputte Corporation). 'Operating Overview of a Producer Gas Plant (12 Machines) at Kingsport, Tennessee.' Presented at the Fifth Annual International Conference on Coal Gasification, Liquefaction and Conversion to Electricity. University of Pittsburgh, August 2, 1978. - Holston Army Ammunition Plant, Producer Gas Plant, Kingsport, Sullivan County, TN

Demand and supply of hydrogen as chemical feedstock in USA

NASA Technical Reports Server (NTRS)

Huang, C. J.; Tang, K.; Kelley, J. H.; Berger, B. J.

1979-01-01

Projections are made for the demand and supply of hydrogen as chemical feedstock in USA. Industrial sectors considered are petroleum refining, ammonia synthesis, methanol production, isocyanate manufacture, edible oil processing, coal liquefaction, fuel cell electricity generation, and direct iron reduction. Presently, almost all the hydrogen required is produced by reforming of natural gas or petroleum fractions. Specific needs and emphases are recommended for future research and development to produce hydrogen from other sources to meet the requirements of these industrial sectors. The data and the recommendations summarized in this paper are based on the Workshop 'Supply and Demand of Hydrogen as Chemical Feedstock' held at the University of Houston on December 12-14, 1977.

MEMBRANE PROCESS TO SEQUESTER CO2 FROM POWER PLANT FLUE GAS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tim Merkel; Karl Amo; Richard Baker

2009-03-31

The objective of this project was to assess the feasibility of using a membrane process to capture CO2 from coal-fired power plant flue gas. During this program, MTR developed a novel membrane (Polaris™) with a CO2 permeance tenfold higher than commercial CO2-selective membranes used in natural gas treatment. The Polaris™ membrane, combined with a process design that uses a portion of combustion air as a sweep stream to generate driving force for CO2 permeation, meets DOE post-combustion CO2 capture targets. Initial studies indicate a CO2 separation and liquefaction cost of $20 - $30/ton CO2 using about 15% of the plantmore » energy at 90% CO2 capture from a coal-fired power plant. Production of the Polaris™ CO2 capture membrane was scaled up with MTR’s commercial casting and coating equipment. Parametric tests of cross-flow and countercurrent/sweep modules prepared from this membrane confirm their near-ideal performance under expected flue gas operating conditions. Commercial-scale, 8-inch diameter modules also show stable performance in field tests treating raw natural gas. These findings suggest that membranes are a viable option for flue gas CO2 capture. The next step will be to conduct a field demonstration treating a realworld power plant flue gas stream. The first such MTR field test will capture 1 ton CO2/day at Arizona Public Service’s Cholla coal-fired power plant, as part of a new DOE NETL funded program.« less

Rapid and solvent-saving liquefaction of woody biomass using microwave-ultrasonic assisted technology.

PubMed

Lu, Zexiang; Wu, Zhengguo; Fan, Liwei; Zhang, Hui; Liao, Yiqiang; Zheng, Deyong; Wang, Siqun

2016-01-01

A novel process to rapidly liquefy sawdust using reduced quantities of solvent, was successfully carried out via microwave-ultrasonic assisted technology (MUAT) in a sulphuric acid/polyethylene glycol 400-glycerol catalytic system. The influences of some key parameters on the liquefaction yield were investigated. The results showed that compared with traditional liquefaction, the introduction of MUAT allowed the solvent dosage to be halved and shortened the liquefaction time from 60 to 20 min. The liquefaction yield reached 91% under the optimal conditions. However, the influence on the yield of some parameters such as catalyst concentration, was similar to that of traditional liquefaction, indicating that the application of MUAT possibly only intensified heat and mass transfer rather than altering either the degradation mechanism or pathway. The introduction of MUAT as a process intensification technology has good industrial application potential for woody biomass liquefaction. Copyright © 2015 Elsevier Ltd. All rights reserved.

Simulation and statistical analysis for the optimization of nitrogen liquefaction plant with cryogenic Claude cycle using process modeling tool: ASPEN HYSYS

NASA Astrophysics Data System (ADS)

Joshi, D. M.

2017-09-01

Cryogenic technology is used for liquefaction of many gases and it has several applications in food process engineering. Temperatures below 123 K are considered to be in the field of cryogenics. Extreme low temperatures are a basic need for many industrial processes and have several applications, such as superconductivity of magnets, space, medicine and gas industries. Several methods can be used to obtain the low temperatures required for liquefaction of gases. The process of cooling or refrigerating a gas to a temperature below its critical temperature so that liquid can be formed at some suitable pressure, which is below the critical pressure, is the basic liquefaction process. Different cryogenic cycle configurations are designed for getting the liquefied form of gases at different temperatures. Each of the cryogenic cycles like Linde cycle, Claude cycle, Kapitza cycle or modified Claude cycle has its own advantages and disadvantages. The placement of heat exchangers, Joule-Thompson valve and turboexpander decides the configuration of a cryogenic cycle. Each configuration has its own efficiency according to the application. Here, a nitrogen liquefaction plant is used for the analysis purpose. The process modeling tool ASPEN HYSYS can provide a software simulation approach before the actual implementation of the plant in the field. This paper presents the simulation and statistical analysis of the Claude cycle with the process modeling tool ASPEN HYSYS. It covers the technique used to optimize the liquefaction of the plant. The simulation results so obtained can be used as a reference for the design and optimization of the nitrogen liquefaction plant. Efficient liquefaction will give the best performance and productivity to the plant.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Strayer, R.F.; Edwards, N.T.; Walton, B.T.

Contaminated soil samples collected from the site of a coal liquefaction product spill were used to study potential fates and effects of this synthetic fuel. Simulated weathering in the laboratory caused significant changes in residual oil composition. Soil column leachates contained high phenol levels that decreased exponentially over time. Toxicity tests demonstrated that the oil-contaminated soil was phytotoxic and caused embryotoxic and teratogenic effects on eggs of the cricket Acheta domesticus.

The oxycoal process with cryogenic oxygen supply.

PubMed

Kather, Alfons; Scheffknecht, Günter

2009-09-01

Due to its large reserves, coal is expected to continue to play an important role in the future. However, specific and absolute CO2 emissions are among the highest when burning coal for power generation. Therefore, the capture of CO2 from power plants may contribute significantly in reducing global CO2 emissions. This review deals with the oxyfuel process, where pure oxygen is used for burning coal, resulting in a flue gas with high CO2 concentrations. After further conditioning, the highly concentrated CO2 is compressed and transported in the liquid state to, for example, geological storages. The enormous oxygen demand is generated in an air-separation unit by a cryogenic process, which is the only available state-of-the-art technology. The generation of oxygen and the purification and liquefaction of the CO2-enriched flue gas consumes significant auxiliary power. Therefore, the overall net efficiency is expected to be lowered by 8 to 12 percentage points, corresponding to a 21 to 36% increase in fuel consumption. Oxygen combustion is associated with higher temperatures compared with conventional air combustion. Both the fuel properties as well as limitations of steam and metal temperatures of the various heat exchanger sections of the steam generator require a moderation of the temperatures during combustion and in the subsequent heat-transfer sections. This is done by means of flue gas recirculation. The interdependencies among fuel properties, the amount and the temperature of the recycled flue gas, and the resulting oxygen concentration in the combustion atmosphere are investigated. Expected effects of the modified flue gas composition in comparison with the air-fired case are studied theoretically and experimentally. The different atmosphere resulting from oxygen-fired combustion gives rise to various questions related to firing, in particular, with regard to the combustion mechanism, pollutant reduction, the risk of corrosion, and the properties of the fly ash or the deposits that form. In particular, detailed nitrogen and sulphur chemistry was investigated by combustion tests in a laboratory-scale facility. Oxidant staging, in order to reduce NO formation, turned out to work with similar effectiveness as for conventional air combustion. With regard to sulphur, a considerable increase in the SO2 concentration was found, as expected. However, the H2S concentration in the combustion atmosphere increased as well. Further results were achieved with a pilot-scale test facility, where acid dew points were measured and deposition probes were exposed to the combustion environment. Besides CO2 and water vapour, the flue gas contains impurities like sulphur species, nitrogen oxides, argon, nitrogen, and oxygen. The CO2 liquefaction is strongly affected by these impurities in terms of the auxiliary power requirement and the CO2 capture rate. Furthermore, the impurity of the liquefied CO2 is affected as well. Since the requirements on the liquid CO2 with regard to geological storage or enhanced oil recovery are currently undefined, the effects of possible flue gas treatment and the design of the liquefaction plant are studied over a wide range.

The oxycoal process with cryogenic oxygen supply

NASA Astrophysics Data System (ADS)

Kather, Alfons; Scheffknecht, Günter

2009-09-01

Due to its large reserves, coal is expected to continue to play an important role in the future. However, specific and absolute CO2 emissions are among the highest when burning coal for power generation. Therefore, the capture of CO2 from power plants may contribute significantly in reducing global CO2 emissions. This review deals with the oxyfuel process, where pure oxygen is used for burning coal, resulting in a flue gas with high CO2 concentrations. After further conditioning, the highly concentrated CO2 is compressed and transported in the liquid state to, for example, geological storages. The enormous oxygen demand is generated in an air-separation unit by a cryogenic process, which is the only available state-of-the-art technology. The generation of oxygen and the purification and liquefaction of the CO2-enriched flue gas consumes significant auxiliary power. Therefore, the overall net efficiency is expected to be lowered by 8 to 12 percentage points, corresponding to a 21 to 36% increase in fuel consumption. Oxygen combustion is associated with higher temperatures compared with conventional air combustion. Both the fuel properties as well as limitations of steam and metal temperatures of the various heat exchanger sections of the steam generator require a moderation of the temperatures during combustion and in the subsequent heat-transfer sections. This is done by means of flue gas recirculation. The interdependencies among fuel properties, the amount and the temperature of the recycled flue gas, and the resulting oxygen concentration in the combustion atmosphere are investigated. Expected effects of the modified flue gas composition in comparison with the air-fired case are studied theoretically and experimentally. The different atmosphere resulting from oxygen-fired combustion gives rise to various questions related to firing, in particular, with regard to the combustion mechanism, pollutant reduction, the risk of corrosion, and the properties of the fly ash or the deposits that form. In particular, detailed nitrogen and sulphur chemistry was investigated by combustion tests in a laboratory-scale facility. Oxidant staging, in order to reduce NO formation, turned out to work with similar effectiveness as for conventional air combustion. With regard to sulphur, a considerable increase in the SO2 concentration was found, as expected. However, the H2S concentration in the combustion atmosphere increased as well. Further results were achieved with a pilot-scale test facility, where acid dew points were measured and deposition probes were exposed to the combustion environment. Besides CO2 and water vapour, the flue gas contains impurities like sulphur species, nitrogen oxides, argon, nitrogen, and oxygen. The CO2 liquefaction is strongly affected by these impurities in terms of the auxiliary power requirement and the CO2 capture rate. Furthermore, the impurity of the liquefied CO2 is affected as well. Since the requirements on the liquid CO2 with regard to geological storage or enhanced oil recovery are currently undefined, the effects of possible flue gas treatment and the design of the liquefaction plant are studied over a wide range.

Microwave-assisted liquefaction of rape straw for the production of bio-oils

Treesearch

Xing-Yan Huang; Feng Li; Jiu-Long Xie; Cornelis F. De Hoop; Chung-Yun Hse; Jin-Qiu Qi; Hui Xiao

2017-01-01

The acid-catalyzed liquefaction of rape straw in methanol using microwave energy was examined. Conversion yield and energy consumption were evaluated to profile the microwave-assisted liquefaction process. Chemical components of the bio-oils from various liquefaction conditions were identified. A higher reaction temperature was found to be beneficial to obtain higher...

Energy from biomass and wastes V; Proceedings of the Fifth Symposium, Lake Buena Vista, FL, January 26-30, 1981

NASA Astrophysics Data System (ADS)

Papers are presented in the areas of biomass production and procurement, biomass and waste combustion, gasification processes, liquefaction processes, environmental effects and government programs. Specific topics include a water hyacinth wastewater treatment system with biomass production, the procurement of wood as an industrial fuel, the cofiring of densified refuse-derived fuel and coal, the net energy production in anaerobic digestion, photosynthetic hydrogen production, the steam gasification of manure in a fluidized bed, and biomass hydroconversion to synthetic fuels. Attention is also given to the economics of deriving alcohol for power applications from grain, ethanol fermentation in a yeast-immobilized column fermenter, a solar-fired biomass flash pyrolysis reactor, particulate emissions from controlled-air modular incinerators, and the DOE program for energy recovery from urban wastes.

Fifteenth symposium on biotechnology for fuels and chemicals: Program and abstracts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-07-01

This collection contains 173 abstracts from presented papers and poster sessions. The five sessions of the conference were on the subjects of: (1) Thermal, Chemical, and Biological Processing, (2) Applied Biological Research, (3) Bioprocessing Research (4), Process Economics and Commercialization, and (5) Environmental Biotechnology. Examples of specific topics in the first session include the kinetics of ripening cheese, microbial liquefaction of lignite, and wheat as a feedstock for fuel ethanol. Typical topics in the second session were synergism studies of bacterial and fungal celluloses, conversion of inulin from jerusalem artichokes to sorbitol and ethanol by saccharomyces cerevisiae, and microbial conversionmore » of high rank coals to methane. The third session entertained topics such as hydrodynamic modeling of a liquid fluidized bed bioreactor for coal biosolubilization, aqueous biphasic systems for biological particle partitioning, and arabinose utilization by xylose-fermenting yeast and fungi. The fourth session included such topics as silage processing of forage biomass to alcohol fuels, economics of molasses to ethanol in India, and production of lactic acid from renewable resources. the final session contained papers on such subjects as bioluminescent detection of contaminants in soils, characterization of petroleum contaminated soils in coral atolls in the south Pacific, and landfill management for methane generation and emission control.« less

Advanced direct coal liquefaction concepts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berger, D.J.; Parker, R.J.; Simpson, P.L.

During the first quarter of FY 1993, the Project proceeded close to the Project Plan. The analysis of the feed material has been completed as far as possible. Some unplanned distillation was needed to correct the boiling range of the Black Thunder solvent used during the autoclave tests. Additional distillation will be required if the same solvent is to be used for the bench unit tests. A decision on this is still outstanding. The solvent to be used with Illinois No. 6 coal has not yet been defined. As a result, the procurement of the feed and the feed analysismore » is somewhat behind schedule. Agglomeration tests with Black Thunder coal indicates that small agglomerates can be formed. However, the ash removal is quite low (about 10%), which is not surprising in view of the low ash content of the coal. The first series of autoclave tests with Black Thunder coal was completed as planned. Also, additional runs are in progress as repeats of previous runs or at different operating conditions based on the data obtained so far. The results are promising indicating that almost complete solubilization (close to 90%) of Black Thunder coal can be achieved in a CO/H[sub 2]O environment at our anticipated process conditions. The design of the bench unit has been completed. In contrast to the originally planned modifications, the bench unit is now designed based on a computerized control and data acquisition system. All major items of equipment have been received, and prefabrication of assemblies and control panels is proceeding on schedule. Despite a slight delay in the erection of the structural steel, it is anticipated that the bench unit will be operational at the beginning of April 1993.« less

Advanced direct coal liquefaction concepts. Quarterly report, October 1, 1992--December 31, 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berger, D.J.; Parker, R.J.; Simpson, P.L.

During the first quarter of FY 1993, the Project proceeded close to the Project Plan. The analysis of the feed material has been completed as far as possible. Some unplanned distillation was needed to correct the boiling range of the Black Thunder solvent used during the autoclave tests. Additional distillation will be required if the same solvent is to be used for the bench unit tests. A decision on this is still outstanding. The solvent to be used with Illinois No. 6 coal has not yet been defined. As a result, the procurement of the feed and the feed analysismore » is somewhat behind schedule. Agglomeration tests with Black Thunder coal indicates that small agglomerates can be formed. However, the ash removal is quite low (about 10%), which is not surprising in view of the low ash content of the coal. The first series of autoclave tests with Black Thunder coal was completed as planned. Also, additional runs are in progress as repeats of previous runs or at different operating conditions based on the data obtained so far. The results are promising indicating that almost complete solubilization (close to 90%) of Black Thunder coal can be achieved in a CO/H{sub 2}O environment at our anticipated process conditions. The design of the bench unit has been completed. In contrast to the originally planned modifications, the bench unit is now designed based on a computerized control and data acquisition system. All major items of equipment have been received, and prefabrication of assemblies and control panels is proceeding on schedule. Despite a slight delay in the erection of the structural steel, it is anticipated that the bench unit will be operational at the beginning of April 1993.« less

Biological production of ethanol from coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Due to the abundant supply of coal in the United States, significant research efforts have occurred over the past 15 years concerning the conversion of coal to liquid fuels. Researchers at the University of Arkansas have concentrated on a biological approach to coal liquefaction, starting with coal-derived synthesis gas as the raw material. Synthesis gas, a mixture of CO, H[sub 2], CO[sub 2], CH[sub 4] and sulfur gases, is first produced using traditional gasification techniques. The CO, CO[sub 2] and H[sub 2] are then converted to ethanol using a bacterial culture of Clostridium 1jungdahlii. Ethanol is the desired product ifmore » the resultant product stream is to be used as a liquid fuel. However, under normal operating conditions, the wild strain'' produces acetate in favor of ethanol in conjunction with growth in a 20:1 molar ratio. Research was performed to determine the conditions necessary to maximize not only the ratio of ethanol to acetate, but also to maximize the concentration of ethanol resulting in the product stream.« less

Biological production of ethanol from coal. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Due to the abundant supply of coal in the United States, significant research efforts have occurred over the past 15 years concerning the conversion of coal to liquid fuels. Researchers at the University of Arkansas have concentrated on a biological approach to coal liquefaction, starting with coal-derived synthesis gas as the raw material. Synthesis gas, a mixture of CO, H{sub 2}, CO{sub 2}, CH{sub 4} and sulfur gases, is first produced using traditional gasification techniques. The CO, CO{sub 2} and H{sub 2} are then converted to ethanol using a bacterial culture of Clostridium 1jungdahlii. Ethanol is the desired product ifmore » the resultant product stream is to be used as a liquid fuel. However, under normal operating conditions, the ``wild strain`` produces acetate in favor of ethanol in conjunction with growth in a 20:1 molar ratio. Research was performed to determine the conditions necessary to maximize not only the ratio of ethanol to acetate, but also to maximize the concentration of ethanol resulting in the product stream.« less

Corrosion Considerations for Thermochemical Biomass Liquefaction Process Systems in Biofuel Production

NASA Astrophysics Data System (ADS)

Brady, M. P.; Keiser, J. R.; Leonard, D. N.; Whitmer, L.; Thomson, J. K.

2014-12-01

Thermochemical liquefaction processing of biomass to produce bio-derived fuels (e.g., gasoline, jet fuel, diesel, home heating oil, etc.) is of great recent interest as a renewable energy source. Approaches under investigation include direct liquefaction, hydrothermal liquefaction, hydropyrolysis, fast pyrolysis, etc., to produce energy dense liquids that can be utilized as produced or further processed to provide products of higher value. An issue with bio-oils is that they tend to contain significant concentrations of organic oxygenates, including acids, which make the bio-oil a potential source of corrosion issues in transport, storage, and use. Efforts devoted to modified/further processing of bio-oils to make them less corrosive are currently being widely pursued. Another issue that must also be addressed in bio-oil liquefaction is potential corrosion issues in the process equipment. Depending on the specific process, bio-oil liquefaction production temperatures are typically in the 300-600°C range, and the process environment can contain aggressive sulfur and halide species from both the biomass used and/or process additives. Detailed knowledge of the corrosion resistance of candidate process equipment alloys in these bio-oil production environments is currently lacking. This paper summarizes recent, ongoing efforts to assess the extent of corrosion of bio-oil process equipment, with the ultimate goal of providing a basis for the selection of the lowest cost alloy grades capable of providing the long-term corrosion resistance needed for future bio-oil production plants.

Conversion of Coal Mine Gas to LNG

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

This project evolved from a 1995, DOE-NETL competitive solicitation for practical CMM capture and utilization concepts. Appalachian Pacific was one of three companies selected to proceed with the construction and operation of a cost-shared demonstration plant. In the course of trying to proceed with this demonstration plant, AP examined several liquefaction technologies, discussed obtaining rights to coal mine methane with a number of coal companies, explored marketing potential with a wide variety of customers in many sections of the United States, studied in great detail the impact of a carbon credit exchange, and developed a suite of analytical tools withmore » which to evaluate possible project options. In the end, the newness of the product, reluctance on the part of the coal companies to venture away from time tested practices, difficulty with obtaining financing, the failure of a carbon credit market to develop and the emergence of shale derived gas production prevented a demonstration plant from being built.« less

Process for the liquefaction of solid carbonaceous materials wherein nitrogen is separated from hydrogen via ammonia synthesis

DOEpatents

Stetka, Steven S.; Nazario, Francisco N.

1982-01-01

In a process for the liquefaction of solid carbonaceous materials wherein bottoms residues are upgraded with a process wherein air is employed, the improvement wherein nitrogen buildup in the system is avoided by ammonia synthesis. In a preferred embodiment hydrogen from other portions of the liquefaction process will be combined with hydrogen produced as a result of the bottoms upgrading to increase the H.sub.2 :N.sub.2 ratio in the ammonia reactor.

Protective Clothing Part 4. Industrial Environments (A Bibliography with Abstracts)

DTIC Science & Technology

1976-04-01

Synthetic rubber, Textiles, Sprays, Gas detectors, Damage control , Propellants IDENTIFIERS: Chlorine trifluoride AD-661 333...and Petroleum (107) Apr 75 Excludes flue gas and other post-combustion sulfur con- trol NTIS/PS-75/381/4GSB Coal Gasification and Liquefaction... desulfurization NTIS/PS-75/455/6GSB Sulfur Dioxide Control . Vol 1. 1964-1972 (159) May 75 NTIS/PS-75/456/4GSB Activated Carbon (221) May

Report of the Materials Research Council (1975)

DTIC Science & Technology

1975-10-01

July 16th 9:00 AM Heinz Heineman - Mobil Research Corporation " Petrochemicals from Alternate Feedstocks" 10󈧢 AM Kenneth Klabunde...Importance of Petrochemicals ; Alternate Feedstocks" -20- . 9:00 AM Fred Steffgan - Bureau of Mines "Coal Liquefaction" 10:30 AM Donald Severson...Africans since 1956. It was recommended that, the construction of about five large synthetic oil plants be commenced at once and that the annual rate

Lignocellulose Liquefaction to Biocrude: A Tutorial Review

PubMed Central

2018-01-01

Abstract After 40 years of research and development, liquefaction technologies are now being demonstrated at 200–3000 tons per year scale to convert lignocellulosic biomass to biocrudes for use as heavy fuel or for upgrading to biofuels. This Review attempts to present the various facets of the liquefaction process in a tutorial manner. Emphasis is placed on liquefaction in high‐boiling solvents, with regular reference to liquefaction in subcritical water or other light‐boiling solvents. Reaction chemistry, solvent selection, role of optional catalyst as well as biocrude composition and properties are discussed in depth. Challenges in biomass feeding and options for biocrude–solvent separation are addressed. Process concepts are reviewed and demonstration/commercialization efforts are presented. PMID:29364569

Exergy analysis of helium liquefaction systems based on modified Claude cycle with two-expanders

NASA Astrophysics Data System (ADS)

Thomas, Rijo Jacob; Ghosh, Parthasarathi; Chowdhury, Kanchan

2011-06-01

Large-scale helium liquefaction systems, being energy-intensive, demand judicious selection of process parameters. An effective tool for design and analysis of thermodynamic cycles for these systems is exergy analysis, which is used to study the behavior of a helium liquefaction system based on modified Claude cycle. Parametric evaluation using process simulator Aspen HYSYS® helps to identify the effects of cycle pressure ratio and expander flow fraction on the exergetic efficiency of the liquefaction cycle. The study computes the distribution of losses at different refrigeration stages of the cycle and helps in selecting optimum cycle pressures, operating temperature levels of expanders and mass flow rates through them. Results from the analysis may help evolving guidelines for designing appropriate thermodynamic cycles for practical helium liquefaction systems.

Design optimization of single mixed refrigerant LNG process using a hybrid modified coordinate descent algorithm

NASA Astrophysics Data System (ADS)

Qyyum, Muhammad Abdul; Long, Nguyen Van Duc; Minh, Le Quang; Lee, Moonyong

2018-01-01

Design optimization of the single mixed refrigerant (SMR) natural gas liquefaction (LNG) process involves highly non-linear interactions between decision variables, constraints, and the objective function. These non-linear interactions lead to an irreversibility, which deteriorates the energy efficiency of the LNG process. In this study, a simple and highly efficient hybrid modified coordinate descent (HMCD) algorithm was proposed to cope with the optimization of the natural gas liquefaction process. The single mixed refrigerant process was modeled in Aspen Hysys® and then connected to a Microsoft Visual Studio environment. The proposed optimization algorithm provided an improved result compared to the other existing methodologies to find the optimal condition of the complex mixed refrigerant natural gas liquefaction process. By applying the proposed optimization algorithm, the SMR process can be designed with the 0.2555 kW specific compression power which is equivalent to 44.3% energy saving as compared to the base case. Furthermore, in terms of coefficient of performance (COP), it can be enhanced up to 34.7% as compared to the base case. The proposed optimization algorithm provides a deep understanding of the optimization of the liquefaction process in both technical and numerical perspectives. In addition, the HMCD algorithm can be employed to any mixed refrigerant based liquefaction process in the natural gas industry.

Efficiency and economics of large scale hydrogen liquefaction. [for future generation aircraft requirements

NASA Technical Reports Server (NTRS)

Baker, C. R.

1975-01-01

Liquid hydrogen is being considered as a substitute for conventional hydrocarbon-based fuels for future generations of commercial jet aircraft. Its acceptance will depend, in part, upon the technology and cost of liquefaction. The process and economic requirements for providing a sufficient quantity of liquid hydrogen to service a major airport are described. The design is supported by thermodynamic studies which determine the effect of process arrangement and operating parameters on the process efficiency and work of liquefaction.

A study of the efficiency of hydrogen liquefaction. [jet aircraft applications

NASA Technical Reports Server (NTRS)

Baker, C. R.; Shaner, R. L.

1976-01-01

The search for an environmentally acceptable fuel to eventually replace petroleum-based fuels for long-range jet aircraft has singled out liquid hydrogen as an outstanding candidate. Hydrogen liquefaction is discussed, along with the effect of several operating parameters on process efficiency. A feasible large-scale commercial hydrogen liquefaction facility based on the results of the efficiency study is described. Potential future improvements in hydrogen liquefaction are noted.

Single-layer transition metal sulfide catalysts

DOEpatents

Thoma, Steven G [Albuquerque, NM

2011-05-31

Transition Metal Sulfides (TMS), such as molybdenum disulfide (MoS.sub.2), are the petroleum industry's "workhorse" catalysts for upgrading heavy petroleum feedstocks and removing sulfur, nitrogen and other pollutants from fuels. We have developed an improved synthesis technique to produce SLTMS catalysts, such as molybdenum disulfide, with potentially greater activity and specificity than those currently available. Applications for this technology include heavy feed upgrading, in-situ catalysis, bio-fuel conversion and coal liquefaction.

Characterization of milled solid residue from cypress liquefaction in sub- and super ethanol.

PubMed

Liu, Hua-Min; Liu, Yu-Lan

2014-01-01

Cypress liquefaction in sub- and super ethanol was carried out in an autoclave at various temperatures. Milled solid residue (MSR) was isolated from solid residue remaining from the liquefaction process, and its chemical characteristics was comparatively investigated with milled wood lignin (MWL) of cypress by sugar analysis, elemental analysis, FT-IR analysis, gel permeation chromatography, and NMR analysis. Results showed that there were two reactions (de-polymerization and re-polymerization) during the cypress liquefaction in sub- and super ethanol and the re-polymerization reactions were the main reaction at 220-260°C. Considering the stability of side-chain, the stability of lignin side-chain in cypress during liquefaction process in ethanol could be sequenced as follows: β-5>β-β'>β-O-4'. The MSR were mainly from the decomposition and re-polymerization of lignin. This study suggests that characterization of MSR provides a promising method to investigate the mechanisms of cypress liquefaction in ethanol. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Economics of hydrogen production and liquefaction updated to 1980

NASA Technical Reports Server (NTRS)

Baker, C. R.

1979-01-01

Revised costs for generating and liquefying hydrogen in mid-1980 are presented. Plant investments were treated as straight-forward escalations resulting from inflation. Operating costs, however, were derived in terms of the unit cost of coal, fuel gas and electrical energy to permit the determination of the influence of these parameters on the cost of liquid hydrogen. Inflationary influence was recognized by requiring a 15% discounted rate of return on investment for Discounted Cash Flow financing analysis, up from 12% previously. Utility financing was revised to require an 11% interest rate on debt. The scope of operation of the hydrogen plant was revised from previous studies to include only the hydrogen generation and liquefaction facilities. On-site fuel gas and power generation, originally a part of the plant complex, was eliminated. Fuel gas and power are now treated as purchased utilities. Costs for on-site generation of fuel gas however, are included.

Stabilisation of bank slopes that are prone to liquefaction in ecologically sensitive areas.

PubMed

Nestler, P; Stoll, R D

2001-01-01

A consequence of lignite stripping in the Lusatia mining district (East Germany) is the backfilling of dumps that mainly consist of low-compacted fine and medium-grained sands. When the ground-water table, which had been lowered while stripping the coal, is rising again, these dumps might be affected by a settlement flow due to the liquefaction of soils. Common methods for stabilisation as, for instance, blasting or vibrator-jetting deep compaction, are not very useful in ecologically sensitive areas, where dumps have been afforested and embankment areas of residual lakes have developed into highly valuable biotopes. A new so-called air-impulse method in combination with directional horizontal drilling has been developed, which does not have a considerably negative impact on the vegetation during compaction. The experience gained during the first employment of this method at the lake "Katja", a residual lake of lignite stripping, is presented in this paper.

Effects of catalysts on liquefaction of Agaricus versicolor (L.)

NASA Astrophysics Data System (ADS)

Durak, Halil

2016-04-01

Supercritical liquefaction process is used for producing energy from biomass. The common reaction conditions for supercritical liquefaction process are the 240-380 °C temperature range and 5-20 Mpa pressure values range. Agaricus versicolor (L.) was liquefied by acetone in an autoclave (75 mL) under high pressure with (aluminium oxide and calcium hydroxide) and without catalyst at 290 °C for producing bio-oil. The products of liquefaction (bio-oil) were analysed and characterized using various methods including elemental analysis, Fourier transform infrared spectroscopy and gas chromatography-mass spectrometry. GC-MS identified 27 different compounds in the bio-oils obtained at 290 °C.

Alternate aircraft fuels: Prospects and operational implications

NASA Technical Reports Server (NTRS)

Witcofski, R. D.

1977-01-01

The potential use of coal-derived aviation fuels was assessed. The studies addressed the prices and thermal efficiencies associated with the production of coal-derived aviation kerosene, liquid methane and liquid hydrogen and the air terminal requirements and subsonic transport performance when utilizing liquid hydrogen. The fuel production studies indicated that liquid methane can be produced at a lower price and with a higher thermal efficiency than aviation kerosene or liquid hydrogen. Ground facilities of liquefaction, storage, distribution and refueling of liquid hydrogen fueled aircraft at airports appear technically feasibile. The aircraft studies indicate modest onboard energy savings for hydrogen compared to conventional fuels. Liquid hydrogen was found to be superior to both aviation kerosene and liquid methane from the standpoint of aircraft engine emissions.

Effect of oxygen compounds addition on the hydrocracking of coal derived liquid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sato, Yoshiki; Kodera, Yoichi; Kamo, Tohru

1998-12-31

Coal derived liquid from liquefaction, coking and low temperature pyrolysis contains considerable amounts of alkylphenols with alkylbenzenes and alkylnaphthalenes. To produce and purify useful chemicals from coal-derived liquid, hydrocracking and hydrotreating of alkylphenol mixture is a very important process. In this study the effects of oxygen compounds such as dimethylcarbonate (DMC) addition on the hydrocracking of alkylphenols and coal-derived liquid were investigated to decrease hydrogen consumption due to the production of water from the removal of OH group. From the hydrocracking of 3,5-dimethylphenol (3,5-DMP) without DMC at 700 C, residence time of 3--10 sec under hydrogen-to-reactant molar ratio of moremore » than 10 using atmospheric flow apparatus with quartz reactor, m-xylene and m-cresol were produced with the production ratio of 1:1.8. However the dehydroxylation to produce m-xylene was decreased by the addition of 10% DMC with the 50% increased production ratio of 1:2.7. These are considered due to the strong interaction between OH group and DMC. Similar reaction behavior was observed in the hydrocracking of 2,5-DMP and the production ratio of (o-cresol + m-cresol)/p-xylene slightly increased from 3.0 to 3.5 by the addition of DMC. On the other hand, the products distribution did not change with and without DMC in the case of 2,6-DMP. This indicates the interaction is hindered by steric effect by the neighboring CH{sub 3} group. The effect of other oxygen compounds on the hydrocracking and the products distribution from the hydrocracking of coal-derived liquids is also discussed.« less

Environmental Fate of a Complex Mixture, Creosote, in Two Species of Fish

DTIC Science & Technology

1994-04-01

tissues, such as edible flesh and ovary [23, 71]. English sole hepatocytes do not form significant amounts of sulfate conjugates of BaP phenols (Figures...Gladys Yanagida (technical support), Dr. Mary Arkoosh for the gift of rainbow trout, Mr. Herb Sanborn for collection of English sole and Eagle Harbor...Research, 265, 223-236. 2. Giddings, J.M., Herbes , S.E., and Gehrs, C.W., (1985) Coal liquefaction products. Environmental Science & Technology, 19, 14-18

Isolation and characterization of cellulose nanofibers from bamboo using microwave liquefaction combined with chemical treatment and ultrasonication

Treesearch

Jiulong Xie; Chung Hse; Cornelis F. De Hoop; Tingxing Hu; Jinqiu Qi; Todd F. Shupe

2016-01-01

Cellulose nanofibers were successfully isolated from bamboo using microwave liquefaction combinedwith chemical treatment and ultrasonic nanofibrillation processes. The microwave liquefaction couldeliminate almost all the lignin in bamboo, resulting in high cellulose content residues within 7 min, andthe cellulose enriched residues could be readily purified by...

Energy technologies and the environment: Environmental information handbook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-10-01

This revision of Energy Technologies and the Environment reflects the changes in energy supply and demand, focus of environmental concern, and emphasis of energy research and development that have occurred since publication of the earlier edition in 1980. The increase in availability of oil and natural gas, at least for the near term, is responsible in part for a reduced emphasis on development of replacement fuels and technologies. Trends in energy development also have been influenced by an increased reliance on private industry initiatives, and a correspondingly reduced government involvement, in demonstrating more developed technologies. Environmental concerns related to acidmore » rain and waste management continue to increase the demand for development of innovative energy systems. The basic criteria for including a technology in this report are that (1) the technology is a major current or potential future energy supply and (2) significant changes in employing or understanding the technology have occurred since publication of the 1980 edition. Coal is seen to be a continuing major source of energy supply, and thus chapters pertaining to the principal coal technologies have been revised from the 1980 edition (those on coal mining and preparation, conventional coal-fired power plants, fluidized-bed combustion, coal gasification, and coal liquefaction) or added as necessary to include emerging technologies (those on oil shale, combined-cycle power plants, coal-liquid mixtures, and fuel cells).« less

Experimental study on the liquefaction of cellulose in supercritical ethanol

NASA Astrophysics Data System (ADS)

Peng, Jinxing; Liu, Xinyuan; Bao, Zhenbo

2018-03-01

Cellulose is the major composition of solid waste for producing biofuel; cellulose liquefaction is helpful for realizing biomass supercritical liquefaction process. This paper is taking supercritical ethanol as the medium, liquefied cellulose with the intermittence installation of high press cauldron. Experiments have studied technical condition and the technology parameter of cellulose liquefaction in supercritical ethanol, and the pyrolysis mechanism was analysed based on the pyrolysis product. Results show that cellulose can be liquefied, can get good effect through appropriate technology condition. Under not catalyst, highest liquefaction rate of cellulose can reach 73.5%. The composition of the pyrolysis product was determined by GC-MS.

Assessment of liquefaction-induced hazards using Bayesian networks based on standard penetration test data

NASA Astrophysics Data System (ADS)

Tang, Xiao-Wei; Bai, Xu; Hu, Ji-Lei; Qiu, Jiang-Nan

2018-05-01

Liquefaction-induced hazards such as sand boils, ground cracks, settlement, and lateral spreading are responsible for considerable damage to engineering structures during major earthquakes. Presently, there is no effective empirical approach that can assess different liquefaction-induced hazards in one model. This is because of the uncertainties and complexity of the factors related to seismic liquefaction and liquefaction-induced hazards. In this study, Bayesian networks (BNs) are used to integrate multiple factors related to seismic liquefaction, sand boils, ground cracks, settlement, and lateral spreading into a model based on standard penetration test data. The constructed BN model can assess four different liquefaction-induced hazards together. In a case study, the BN method outperforms an artificial neural network and Ishihara and Yoshimine's simplified method in terms of accuracy, Brier score, recall, precision, and area under the curve (AUC) of the receiver operating characteristic (ROC). This demonstrates that the BN method is a good alternative tool for the risk assessment of liquefaction-induced hazards. Furthermore, the performance of the BN model in estimating liquefaction-induced hazards in Japan's 2011 Tōhoku earthquake confirms its correctness and reliability compared with the liquefaction potential index approach. The proposed BN model can also predict whether the soil becomes liquefied after an earthquake and can deduce the chain reaction process of liquefaction-induced hazards and perform backward reasoning. The assessment results from the proposed model provide informative guidelines for decision-makers to detect the damage state of a field following liquefaction.

Dynamic dielectric properties of a wood liquefaction system using polyethylene glycol and glycerol

Treesearch

Mengchao Zhou; Thomas L. Eberhardt; Bo Cai; Chung-Yun Hse; Hui Pan

2017-01-01

Microwave-assisted liquefaction has shown potential for rapid thermal processing of lignocellulosic biomass. The efficiency of microwave heating depends largely on the dielectric properties of the materials being heated. The objective of this study was to investigate the dynamic interactions between microwave energy and the reaction system during the liquefaction of a...

Corrosion considerations for thermochemical biomass liquefaction process systems in biofuel production

DOE PAGES

Brady, Michael P.; Keiser, James R.; Leonard, Donovan N.; ...

2014-11-11

Thermochemical liquifaction processing of biomass to produce bio-derived fuels (e.g. gasoline, jet fuel, diesel, home heating oil, etc.) is of great recent interest as a renewable energy source. Approaches under investigation include direct liquefaction, hydrothermal liquefaction, hydropyrolysis, fast pyrolysis, etc. to produce energy dense liquids that can be utilized as produced or further processed to provide products of higher value. An issue with bio-oils is that they tend to contain significant concentrations of organic compounds, which make the bio-oil acidic and a potential source of corrosion issues in in transport, storage, and use. Efforts devoted to modified/further processing of bio-oilsmore » to make them less corrosive are currently being widely pursued. Another aspect that must also be addressed is potential corrosion issues in the bio-oil liquefaction process equipment itself. Depending on the specific process, bio-oil liquefaction production temperatures can reach up to 400-600 °C, and involve the presence of aggressive sulfur, and halide species from both the biomass used and/or process additives. Detailed knowledge of the corrosion resistance of candidate process equipment alloys in these bio-oil production environments is currently lacking. Lastly, this paper summarizes our recent, ongoing efforts to assess the extent to which corrosion of bio-oil process equipment may be an issue, with the ultimate goal of providing the basis to select the lowest cost alloy grades capable of providing the long-term corrosion resistance needed for future bio-oil production plants.« less

Cross-flow electrofilter and method

DOEpatents

Gidaspow, Dimitri; Lee, Chang H.; Wasan, Darsh T.

1980-01-01

A filter for clarifying carbonaceous liquids containing finely divided solid particles of, for instance, unreacted coal, ash and other solids discharged from a coal liquefaction process is presented. The filter includes two passageways separated by a porous filter medium. In one preferred embodiment the filter medium is of tubular shape to form the first passageway and is enclosed within an outer housing to form the second passageway within the annulus. An electrode disposed in the first passageway, for instance along the tube axis, is connected to a source of high voltage for establishing an electric field between the electrode and the filter medium. Slurry feed flows through the first passageway tangentially to the surfaces of the filter medium and the electrode. Particles from the feed slurry are attracted to the electrode within the first passageway to prevent plugging of the porous filter medium while carbonaceous liquid filters into the second passageway for withdrawal. Concentrated slurry is discharged from the first passageway at an end opposite to the feed slurry inlet. Means are also provided for the addition of diluent and a surfactant into the slurry to control relative permittivity and the electrophoretic mobility of the particles.

Cross flow electrofilter and method

DOEpatents

Gidaspow, Dimitri; Lee, Chang H.; Wasan, Darsh T.

1981-01-01

A filter for clarifying carbonaceous liquids containing finely divided solid particles of, for instance, unreacted coal, ash and other solids discharged from a coal liquefaction process is presented. The filter includes two passageways separated by a porous filter medium. In one preferred embodiment the filter medium is of tubular shape to form the first passageway and is enclosed within an outer housing to form the second passageway within the annulus. An electrode disposed in the first passageway, for instance along the tube axis, is connected to a source of high voltage for establishing an electric field between the electrode and the filter medium. Slurry feed flows through the first passageway tangentially to the surfaces of the filter medium and the electrode. Particles from the feed slurry are attracted to the electrode within the first passageway to prevent plugging of the porous filter medium while carbonaceous liquid filters into the second passageway for withdrawal. Concentrated slurry is discharged from the first passageway at an end opposite to the feed slurry inlet. Means are also provided for the addition of diluent and a surfactant into the slurry to control relative permittivity and the electrophoretic mobility of the particles.

Methods for the isolation and identification of polycyclic aromatic hydrocarbons found in complex mixtures and the determination of their possible toxicity by means of a host mediated bioassay technique. Progress report, July 1, 1976--February 1, 1977. [Cultured mouse leumemia cell bioassay system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lipsky, S.R.; Alexander, G.; McMurray, W.

1977-02-01

Techniques were developed to produce excellent high performance glass capillary columns for gas chromatographic analyses of a wide range of complex mixtures of organic compounds, including those containing a wide array of polycyclic aromatic hydrocarbons (PAH) derived from a coal liquefaction process. Work was begun to assess the potential mutogenicity and/or carcinogenicity of the various isolated PAH fractions utilizing a unique host mediated bioassay system. Preliminary results indicate that further efforts will be required to determine dose response parameters of cultured mouse leukemia cells, as well as suitable vehicles for the satisfactory introduction of certain PAH fractions into this particularmore » bioassay system.« less

Renewable chemical feedstocks from integrated liquefaction processing of lingocellulosic materials using microwave energy

Treesearch

Junming Xu; Jianchun Jiang; Chung-Yun Hse; Todd F. Shupe

2012-01-01

The objective of this investigation was to find a simple method for the production of phenolic rich products and sugar derivatives (biopolyols) via separation of liquefied lingocellulosic materials. Liquefaction of lignocellulosic materials was conducted in methanol at 180 °C for 15 min with the conversion of raw materials at about 75%. After liquefaction, the...

Co-liquefaction of spent coffee grounds and lignocellulosic feedstocks.

PubMed

Yang, Linxi; He, Quan Sophia; Havard, Peter; Corscadden, Kenneth; Xu, Chunbao Charles; Wang, Xuan

2017-08-01

Co-liquefaction of spent coffee grounds (SCG) with paper filter (PF), corn stalk (CS) and white pine bark (WPB) respectively, was examined in subcritical water for bio-crude oil production. The optimum reaction temperature was 250°C, and the mixing biomass ratio was 1:1. SCG and CS was identified to be the best feedstock combination with a significant positive synergetic effect in the co-liquefaction process with 5% NaOH as a catalyst. The yield of bio-crude oil was increased by 20.9% compared to the mass averaged yield from two feedstocks, and the oil quality was also improved in terms of viscosity and relative molecular mass. A negative effect presented in the co-liquefaction of SCG/WPB. The resulting bio-crude oils were characterized by elemental analyzer, GC-MS, GPC and viscometer, indicating that mixing feedstock in the co-liquefaction process also influenced the higher heating value (HHV), viscosity, molecular mass and chemical composition of bio-crude oil. Copyright © 2017 Elsevier Ltd. All rights reserved.

Impact of an acid fungal protease in high gravity fermentation for ethanol production using Indian sorghum as a feedstock.

PubMed

Gohel, V; Duan, G; Maisuria, V B

2013-01-01

This study evaluated the conventional jet cooking liquefaction process followed by simultaneous saccharification and fermentation (SSF) at 30% and 35% dry solids (DS) concentration of Indian sorghum feedstock for ethanol production, with addition of acid fungal protease or urea. To evaluate the efficacy of thermostable α-amylase in liquefaction at 30% and 35% DS concentration of Indian sorghum, liquefact solubility, higher dextrins, and fermentable sugars were analyzed at the end of the process. The liquefact was further subjected to SSF using yeast. In comparison with urea, addition of an acid fungal protease during SSF process was observed to accelerate yeast growth (μ), substrate consumption (Q(s)), ultimately ethanol yield based on substrate (Y(p/s)) and ethanol productivity based on fermentation time (Q(p)). The fermentation efficiency and ethanol recovery were determined for both concentrations of Indian sorghum and found to be increased with use of acid fungal protease in SSF process. Copyright © 2013 American Institute of Chemical Engineers.

Liquefaction of lignocellulosic biomass: solvent, process parameter, and recycle oil screening.

PubMed

van Rossum, Guus; Zhao, Wei; Castellvi Barnes, Maria; Lange, Jean-Paul; Kersten, Sascha R A

2014-01-01

The liquefaction of lignocellulosic biomass is studied for the production of liquid (transportation) fuels. The process concept uses a product recycle as a liquefaction medium and produces a bio-oil that can be co-processed in a conventional oil refinery. This all is done at medium temperature (≈ 300 °C) and pressure (≈ 60 bar). Solvent-screening experiments showed that oxygenated solvents are preferred as they allow high oil (up to 93% on carbon basis) and low solid yields (≈ 1-2% on carbon basis) and thereby outperform the liquefaction of biomass in compressed water and biomass pyrolysis. The following solvent ranking was obtained: guaiacol>hexanoic acid ≫ n-undecane. The use of wet biomass results in higher oil yields than dry biomass. However, it also results in a higher operating pressure, which would make the process more expensive. Refill experiments were also performed to evaluate the possibility to recycle the oil as the liquefaction medium. The recycled oil appeared to be very effective to liquefy the biomass and even surpassed the start-up solvent guaiacol, but became increasingly heavy and more viscous after each refill and eventually showed a molecular weight distribution that resembles that of refinery vacuum residue. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Dispersed catalysts for co-processing and coal liquefaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bockrath, B.; Parfitt, D.; Miller, R.

1995-12-31

The basic goal is to improve dispersed catalysts employed in the production of clean fuels from low value hydrocarbons. The immediate objective is to determine how the properties of the catalysts may be altered to match the demands placed on them by the properties of the feedstock, the qualities of the desired end products, and the economic constraints put upon the process. Several interrelated areas of the application of dispersed catalysts to co-processing and coal conversion are under investigation. The first involves control of the selectivity of MoS{sub 2} catalysts for HDN, HDS, and hydrogenation of aromatics. A second areamore » of research is the development and use of methods to evaluate dispersed catalysts by means of activity and selectivity tests. A micro-flow reactor has been developed for determining intrinsic reactivities using model compounds, and will be used to compare catalysts prepared in different ways. Micro-autoclaves will also be used to develop data in batch experiments at higher partial pressures of hydrogen. The third area under investigation concerns hydrogen spillover reactions between MoS{sub 2} catalysts and carbonaceous supports. Preliminary results obtained by monitoring H{sub 2}/D{sub 2} exchange reactions with a pulse-flow microreactor indicate the presence of spillover between MoS{sub 2} and a graphitic carbon. A more complete study will be made at a later stage of the project. Accomplishments and conclusions are discussed.« less

Analysis of Cryogenic Cycle with Process Modeling Tool: Aspen HYSYS

NASA Astrophysics Data System (ADS)

Joshi, D. M.; Patel, H. K.

2015-10-01

Cryogenic engineering deals with the development and improvement of low temperature techniques, processes and equipment. A process simulator such as Aspen HYSYS, for the design, analysis, and optimization of process plants, has features that accommodate the special requirements and therefore can be used to simulate most cryogenic liquefaction and refrigeration processes. Liquefaction is the process of cooling or refrigerating a gas to a temperature below its critical temperature so that liquid can be formed at some suitable pressure which is below the critical pressure. Cryogenic processes require special attention in terms of the integration of various components like heat exchangers, Joule-Thompson Valve, Turbo expander and Compressor. Here, Aspen HYSYS, a process modeling tool, is used to understand the behavior of the complete plant. This paper presents the analysis of an air liquefaction plant based on the Linde cryogenic cycle, performed using the Aspen HYSYS process modeling tool. It covers the technique used to find the optimum values for getting the maximum liquefaction of the plant considering different constraints of other parameters. The analysis result so obtained gives clear idea in deciding various parameter values before implementation of the actual plant in the field. It also gives an idea about the productivity and profitability of the given configuration plant which leads to the design of an efficient productive plant.

Extraction and characterization of holocellulose fibers by microwave-assisted selective liquefaction of bamboo

Treesearch

Jiulong Xie; Chung Hse; Todd F. Shupe; Hui Pan; Tingxing Hu

2016-01-01

Microwave-assisted selective liquefaction was proposed and used as a novel method for the isolation of holocellulose fibers. The results showed that the bamboo lignin component and extractives were almost completely removed by using a liquefaction process at 120 8C for 9 min, and the residual lignin and extractives in the solid residue were as low as 0.65% and 0.49%,...

Review of nonconventional bioreactor technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turick, C.E.; Mcllwain, M.E.

1993-09-01

Biotechnology will significantly affect many industrial sectors in the future. Industrial sectors that will be affected include pharmaceutical, chemical, fuel, agricultural, and environmental remediation. Future research is needed to improve bioprocessing efficiency and cost-effectiveness in order to compete with traditional technologies. This report describes recent advances in bioprocess technologies and bioreactor designs and relates them to problems encountered in many industrial bioprocessing operations. The primary focus is directed towards increasing gas and vapor transfer for enhanced bioprocess kinetics as well as unproved by-product separation and removal. The advantages and disadvantages of various conceptual designs such as hollow-fiber, gas-phase, hyperbaric/hypobaric, andmore » electrochemical bioreactors are also discussed. Specific applications that are intended for improved bioprocesses include coal desulfurization, coal liquefaction, soil bioremediation, biomass conversion to marketable chemicals, biomining, and biohydrometallurgy as well as bioprocessing of gases and vapors.« less

Analysis and optimisation of a mixed fluid cascade (MFC) process

NASA Astrophysics Data System (ADS)

Ding, He; Sun, Heng; Sun, Shoujun; Chen, Cheng

2017-04-01

A mixed fluid cascade (MFC) process that comprises three refrigeration cycles has great capacity for large-scale LNG production, which consumes a great amount of energy. Therefore, any performance enhancement of the liquefaction process will significantly reduce the energy consumption. The MFC process is simulated and analysed by use of proprietary software, Aspen HYSYS. The effect of feed gas pressure, LNG storage pressure, water-cooler outlet temperature, different pre-cooling regimes, liquefaction, and sub-cooling refrigerant composition on MFC performance are investigated and presented. The characteristics of its excellent numerical calculation ability and the user-friendly interface of MATLAB™ and powerful thermo-physical property package of Aspen HYSYS are combined. A genetic algorithm is then invoked to optimise the MFC process globally. After optimisation, the unit power consumption can be reduced to 4.655 kW h/kmol, or 4.366 kW h/kmol on condition that the compressor adiabatic efficiency is 80%, or 85%, respectively. Additionally, to improve the process further, with regards its thermodynamic efficiency, configuration optimisation is conducted for the MFC process and several configurations are established. By analysing heat transfer and thermodynamic performances, the configuration entailing a pre-cooling cycle with three pressure levels, liquefaction, and a sub-cooling cycle with one pressure level is identified as the most efficient and thus optimal: its unit power consumption is 4.205 kW h/kmol. Additionally, the mechanism responsible for the weak performance of the suggested liquefaction cycle configuration lies in the unbalanced distribution of cold energy in the liquefaction temperature range.

Biomass Direct Liquefaction Options. TechnoEconomic and Life Cycle Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tews, Iva J.; Zhu, Yunhua; Drennan, Corinne

The purpose of this work was to assess the competitiveness of two biomass to transportation fuel processing routes, which were under development in Finland, the U.S. and elsewhere. Concepts included fast pyrolysis (FP), and hydrothermal liquefaction (HTL), both followed by hydrodeoxygenation, and final product refining. This work was carried out as a collaboration between VTT (Finland), and PNNL (USA). The public funding agents for the work were Tekes in Finland and the Bioenergy Technologies Office of the U.S. Department of Energy. The effort was proposed as an update of the earlier comparative technoeconomic assessment performed by the IEA Bioenergy Directmore » Biomass Liquefaction Task in the 1980s. New developments in HTL and the upgrading of the HTL biocrude product triggered the interest in reinvestigating this comparison of these biomass liquefaction processes. In addition, developments in FP bio-oil upgrading had provided additional definition of this process option, which could provide an interesting comparison.« less

A spotlight on liquefaction: evidence from clinical settings and experimental models in tuberculosis.

PubMed

Cardona, Pere-Joan

2011-01-01

Liquefaction is one of the most intriguing aspects of human tuberculosis. It is a major cause of the transition from the infection to active disease (tuberculosis, TB) as well as the transmission of M. tuberculosis to other persons. This paper reviews the natural history of liquefaction in humans from a pathological and radiological point of view and discusses how the experimental models available can be used to address the topic of liquefaction and cavity formation. Different concepts that have been related to liquefaction, from the influence of immune response to mechanical factors, are reviewed. Synchronic necrosis or apoptosis of infected macrophages in a close area, together with an ineffective fibrosis, appears to be clue in this process, in which macrophages, the immune response, and bacillary load interact usually in a particular scenario: the upper lobes of the lung. The summary would be that even if being a stochastic effect, liquefaction would result if the organization of the intragranulomatous necrosis (by means of fibrosis) would be disturbed.

A Spotlight on Liquefaction: Evidence from Clinical Settings and Experimental Models in Tuberculosis

PubMed Central

Cardona, Pere-Joan

2011-01-01

Liquefaction is one of the most intriguing aspects of human tuberculosis. It is a major cause of the transition from the infection to active disease (tuberculosis, TB) as well as the transmission of M. tuberculosis to other persons. This paper reviews the natural history of liquefaction in humans from a pathological and radiological point of view and discusses how the experimental models available can be used to address the topic of liquefaction and cavity formation. Different concepts that have been related to liquefaction, from the influence of immune response to mechanical factors, are reviewed. Synchronic necrosis or apoptosis of infected macrophages in a close area, together with an ineffective fibrosis, appears to be clue in this process, in which macrophages, the immune response, and bacillary load interact usually in a particular scenario: the upper lobes of the lung. The summary would be that even if being a stochastic effect, liquefaction would result if the organization of the intragranulomatous necrosis (by means of fibrosis) would be disturbed. PMID:21437230

Liquefaction of Semen Generates and Later Degrades a Conserved Semenogelin Peptide That Enhances HIV Infection

PubMed Central

Liu, Haichuan; Usmani, Shariq M.; Neidleman, Jason; Müller, Janis A.; Avila-Herrera, Aram; Gawanbacht, Ali; Zirafi, Onofrio; Chu, Simon; Dong, Ming; Kumar, Senthil T.; Smith, James F.; Pollard, Katherine S.; Fändrich, Marcus; Kirchhoff, Frank; Münch, Jan; Witkowska, H. Ewa; Greene, Warner C.

2014-01-01

ABSTRACT Semen enhances HIV infection in vitro, but how long it retains this activity has not been carefully examined. Immediately postejaculation, semen exists as a semisolid coagulum, which then converts to a more liquid form in a process termed liquefaction. We demonstrate that early during liquefaction, semen exhibits maximal HIV-enhancing activity that gradually declines upon further incubation. The decline in HIV-enhancing activity parallels the degradation of peptide fragments derived from the semenogelins (SEMs), the major components of the coagulum that are cleaved in a site-specific and progressive manner upon initiation of liquefaction. Because amyloid fibrils generated from SEM fragments were recently demonstrated to enhance HIV infection, we set out to determine whether any of the liquefaction-generated SEM fragments associate with the presence of HIV-enhancing activity. We identify SEM1 from amino acids 86 to 107 [SEM1(86-107)] to be a short, cationic, amyloidogenic SEM peptide that is generated early in the process of liquefaction but that, conversely, is lost during prolonged liquefaction due to the activity of serine proteases. Synthetic SEM1(86-107) amyloids directly bind HIV-1 virions and are sufficient to enhance HIV infection of permissive cells. Furthermore, endogenous seminal levels of SEM1(86-107) correlate with donor-dependent variations in viral enhancement activity, and antibodies generated against SEM1(86-107) recognize endogenous amyloids in human semen. The amyloidogenic potential of SEM1(86-107) and its virus-enhancing properties are conserved among great apes, suggesting an evolutionarily conserved function. These studies identify SEM1(86-107) to be a key, HIV-enhancing amyloid species in human semen and underscore the dynamic nature of semen's HIV-enhancing activity. IMPORTANCE Semen, the most common vehicle for HIV transmission, enhances HIV infection in vitro, but how long it retains this activity has not been investigated. Semen naturally undergoes physiological changes over time, whereby it converts from a gel-like consistency to a more liquid form. This process, termed liquefaction, is characterized at the molecular level by site-specific and progressive cleavage of SEMs, the major components of the coagulum, by seminal proteases. We demonstrate that the HIV-enhancing activity of semen gradually decreases over the course of extended liquefaction and identify a naturally occurring semenogelin-derived fragment, SEM1(86-107), whose levels correlate with virus-enhancing activity over the course of liquefaction. SEM1(86-107) amyloids are naturally present in semen, and synthetic SEM1(86-107) fibrils bind virions and are sufficient to enhance HIV infection. Therefore, by characterizing dynamic changes in the HIV-enhancing activity of semen during extended liquefaction, we identified SEM1(86-107) to be a key virus-enhancing component of human semen. PMID:24741080

Production of biofuels via bio-oil upgrading & refining

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elliott, Douglas C.

2016-03-18

This chapter provides cursory reviews of biomass liquefaction, relevant petroleum processing technology, and relevant model compound studies. More detail is provided for upgrading of biomass liquefaction products, including an overview of potential fractionation and catalytic processing methods, hydroprocessing as the primary means of interest, scale of operation, operating conditions and catalysts, and product properties. Batch results are included where needed to provide a more complete narrative, but continuous-flow operations are emphasized as being more informative. Liquid fuel products from biomass through direct liquefaction and hydroprocessing are discussed, such as fuel properties based on chemical analysis and comparison of petroleum fuelsmore » and biofuels.« less

Microscale evidence of liquefaction and its potential triggers during soft-bed deformation within subglacial traction tills

NASA Astrophysics Data System (ADS)

Phillips, Emrys R.; Evans, David J. A.; van der Meer, Jaap J. M.; Lee, Jonathan R.

2018-02-01

Published conceptual models argue that much of the forward motion of modern and ancient glaciers is accommodated by deformation of soft-sediments within the underlying bed. At a microscale this deformation results in the development of a range of ductile and brittle structures in water-saturated sediments as they accommodate the stresses being applied by the overriding glacier. Detailed micromorphological studies of subglacial traction tills reveal that these polydeformed sediments may also contain evidence of having undergone repeated phases of liquefaction followed by solid-state shear deformation. This spatially and temporally restricted liquefaction of subglacial traction tills lowers the shear strength of the sediment and promotes the formation of "transient mobile zones" within the bed, which accommodate the shear imposed by the overriding ice. This process of soft-bed sliding, alternating with bed deformation, facilitates glacier movement by way of 'stick-slip' events. The various controls on the slip events have previously been identified as: (i) the introduction of pressurised meltwater into the bed, a process limited by the porosity and permeability of the till; and (ii) pressurisation of porewater as a result of subglacial deformation; to which we include (iii) episodic liquefaction of water-saturated subglacial traction tills in response to glacier seismic activity (icequakes), which are increasingly being recognized as significant processes in modern glaciers and ice sheets. As liquefaction operates only in materials already at very low values of effective stress, its process-form signatures are likely indicative of glacier sub-marginal tills.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alan W. Scaroni; David C. Glick

This project generated and provided coal samples and accompanying analytical data for research by DOE contractors and others. The five-year contract and a six-month no-cost extension have been completed. The Final Technical Progress Report is being prepared. All activities specified under the five-year contract and its six-month no-cost extension have been completed. Eleven DECS samples were collected, processed to a variety of particle sizes, heat-sealed in foil laminate bags under argon, and placed in refrigerated storage. All were analyzed for basic chemical composition, inorganic major and trace element composition including hazardous air pollutant elements, petrographic composition and characteristics, thermoplastic behaviormore » (if applicable), and other properties relevant to commercial utilization. Most were also analyzed by NMR, py/gc/ms, and a standardized liquefaction test; trends and relationships observed were evaluated and summarized. Twenty-two DECS samples collected under the previous contract received further processing, and most of these were subjected to organic geochemical and standardized liquefaction tests as well. Selected DECS samples were monitored annually to evaluate the effectiveness of foil laminate bags for long-term sample storage. Twenty-three PSOC samples collected under previous contracts and purged with argon before storage were also maintained and distributed, for a total of 56 samples covered by the contract. During the contract, 804 samples in 1586 containers, 2109 data printouts, and individual data items from 34208 samples were distributed. In the subject quarter, 25 samples, 18 data printouts, and individual data items from 1374 samples were distributed. All DECS samples are now available for immediate distribution at minus 6 mm (-1/4 inch), minus 0.85 mm (-20 mesh U.S.), and minus 0.25 mm (-60 mesh U.S.).« less

Liquefaction of ground tire rubber at low temperature.

PubMed

Cheng, Xiangyun; Song, Pan; Zhao, Xinyu; Peng, Zonglin; Wang, Shifeng

2018-01-01

Low-temperature liquefaction has been investigated as a novel method for recycling ground tire rubber (GTR) into liquid using an environmentally benign process. The liquefaction was carried out at different temperatures (140, 160 and 180 °C) over variable time ranges (2-24 h) by blending the GTR with aromatic oil in a range from 0 to 100 parts per hundred rubber (phr). The liquefied GTR was separated into sol (the soluble fraction of rubber which can be extracted with toluene) and gel fractions (the solid fraction obtained after extraction) to evaluate the reclaiming efficiency. It was discovered that the percentage of the sol fraction increased with time, swelling ratio and temperature. Liquefied rubber was obtained with a high sol fraction (68.34 wt%) at 140 °C. Simultaneously, separation of nano-sized carbon black from the rubber networks occurred. The separation of carbon black from the network is the result of significant damage to the cross-linked-network that occurs throughout the liquefaction process. During liquefaction, a competitive reaction between main chain scission and cross-link bond breakage takes place. Copyright © 2017 Elsevier Ltd. All rights reserved.

Thermodynamic analysis of low-temperature carbon dioxide and sulfur dioxide capture from coal-burning power plants.

PubMed

Swanson, Charles E; Elzey, John W; Hershberger, Robert E; Donnelly, Russell J; Pfotenhauer, John

2012-07-01

We discuss the possibility of capturing carbon dioxide from the flue gas of a coal-fired electrical power plant by cryogenically desublimating the carbon dioxide and then preparing it for transport in a pipeline to a sequestration site. Various other means have been proposed to accomplish the same goal. The problem discussed here is to estimate the "energy penalty" or "parasitic energy loss,' defined as the fraction of electrical output that will be needed to provide the refrigeration and that will then not be deliverable. We compute the energy loss (7.9-9.2% at 1 atm) based on perfect Carnot efficiency and estimate the achievable parasitic energy loss (22-26% at 1 atm) by incorporating the published coefficient of performance values for appropriately sized refrigeration or liquefaction cycles at the relevant temperatures. The analyses at 1 atm represent a starting point for future analyses using elevated pressures.

Thermodynamic analysis of low-temperature carbon dioxide and sulfur dioxide capture from coal-burning power plants

NASA Astrophysics Data System (ADS)

Swanson, Charles E.; Elzey, John W.; Hershberger, Robert E.; Donnelly, Russell J.; Pfotenhauer, John

2012-07-01

We discuss the possibility of capturing carbon dioxide from the flue gas of a coal-fired electrical power plant by cryogenically desublimating the carbon dioxide and then preparing it for transport in a pipeline to a sequestration site. Various other means have been proposed to accomplish the same goal. The problem discussed here is to estimate the “energy penalty” or “parasitic energy loss,' defined as the fraction of electrical output that will be needed to provide the refrigeration and that will then not be deliverable. We compute the energy loss (7.9-9.2% at 1 atm) based on perfect Carnot efficiency and estimate the achievable parasitic energy loss (22-26% at 1 atm) by incorporating the published coefficient of performance values for appropriately sized refrigeration or liquefaction cycles at the relevant temperatures. The analyses at 1 atm represent a starting point for future analyses using elevated pressures.

Liquefaction process wherein solvents derived from the material liquefied and containing increased concentrations of donor species are employed

DOEpatents

Fant, B. T.; Miller, John D.; Ryan, D. F.

1982-01-01

An improved process for the liquefaction of solid carbonaceous materials wherein a solvent or diluent derived from the solid carbonaceous material being liquefied is used to form a slurry of the solid carbonaceous material and wherein the solvent or diluent comprises from about 65 to about 85 wt. % hydroaromatic components. The solvent is prepared by first separating a solvent or diluent distillate fraction from the liquefaction product, subjecting this distillate fraction to hydrogenation and then extracting the naphthenic components from the hydrogenated product. The extracted naphthenic components are then dehydrogenated and hydrotreated to produce additional hydroaromatic components. These components are combined with the solvent or diluent distillate fraction. The solvent may also contain hydroaromatic constituents prepared by extracting naphthenic components from a heavy naphtha, dehydrogenating the same and then hydrotreating the dehydrogenated product. When the amount of solvent produced in this manner exceeds that required for steady state operation of the liquefaction process a portion of the solvent or diluent distillated fraction will be withdrawn as product.

Catalytic Upgrading of Thermochemical Intermediates to Hydrocarbons: Conversion of Lignocellulosic Feedstocks to Aromatic Fuels and High Value Chemicals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cortright, Randy; Rozmiarek, Bob; Van Straten, Matt

The principal objective of this project was to develop a fully integrated catalytic process that efficiently converts lignocellulosic feedstocks (e.g. bagasse, corn stover, and loblolly pine) into aromatic-rich fuels and chemicals. Virent led this effort with key feedstock support from Iowa State University. Within this project, Virent leveraged knowledge of catalytic processing of sugars and biomass to investigate two liquefaction technologies (Reductive Catalytic Liquefaction (USA Patent No. 9,212,320, 2015) and Solvolysis (USA Patent No. 9,157,030, 2015) (USA Patent No. 9,157,031, 2015)) that take advantage of proprietary catalysts at temperatures less than 300°C in the presence of unique solvent molecules generatedmore » in-situ within the liquefaction processes.« less

Apparatus for the liquefaction of natural gas and methods relating to same

DOEpatents

Wilding, Bruce M [Idaho Falls, ID; Bingham, Dennis N [Idaho Falls, ID; McKellar, Michael G [Idaho Falls, ID; Turner, Terry D [Ammon, ID; Raterman, Kevin T [Idaho Falls, ID; Palmer, Gary L [Shelley, ID; Klingler, Kerry M [Idaho Falls, ID; Vranicar, John J [Concord, CA

2007-05-22

An apparatus and method for producing liquefied natural gas. A liquefaction plant may be coupled to a source of unpurified natural gas, such as a natural gas pipeline at a pressure letdown station. A portion of the gas is drawn off and split into a process stream and a cooling stream. The cooling stream passes through a turbo expander creating work output. A compressor is driven by the work output and compresses the process stream. The compressed process stream is cooled, such as by the expanded cooling stream. The cooled, compressed process stream is divided into first and second portions with the first portion being expanded to liquefy the natural gas. A gas-liquid separator separates the vapor from the liquid natural gas. The second portion of the cooled, compressed process stream is also expanded and used to cool the compressed process stream. Additional features and techniques may be integrated with the liquefaction process including a water clean-up cycle and a carbon dioxide (CO.sub.2) clean-up cycle.

Thermal properties of biopolyol from oil palm fruit fibre (OPFF) using solvolysis liquefaction technique

NASA Astrophysics Data System (ADS)

Kormin, Shaharuddin; Rus, Anika Zafiah M.; Azahari, M. Shafiq M.

2017-09-01

Liquefaction is known to be an effective method for converting biomass into a biopolyol. The biomass liquefaction of oil palm fruit waste (PFW) in the presence of liquefaction solvent/polyhydric alcohol (PA): polyethylene glycol 400 (PEG400) using sulfuric acid as catalyst was studied. For all experiments, the liquefaction was conducted at 150°C and atmospheric pressure. The mass ratio of OPFW to liquefaction solvents used in all the experiments was, 1/3. Thermogravimetric analyses (TGA) were used to analyze their biopolyol and residue behaviors. It was found that thermal stability of oil palm mesocarp fibre (PM), oil palm shell (PS) and oil palm kernel (PK) fibre exhibited the first degradation of hard segment at (232, 104, 230°C) and the second degradation of soft segment at (314, 226, 412°C) as compared to PM, PS and PK residue which (229, 102, 227°C) of hard segment and (310, 219, 299°C) of segment, respectively. This behavior of thermal degradation of the hard segment and soft segment of biopolyol was changes after undergo solvolysis liquefaction process. The result analysis showed that the resulting biopolyol and its residue was suitable monomer for polyurethane (PU) synthesis for the production of PU foams.

CPT site characterization for seismic hazards in the New Madrid seismic zone

USGS Publications Warehouse

Liao, T.; Mayne, P.W.; Tuttle, M.P.; Schweig, E.S.; Van Arsdale, R.B.

2002-01-01

A series of cone penetration tests (CPTs) were conducted in the vicinity of the New Madrid seismic zone in central USA for quantifying seismic hazards, obtaining geotechnical soil properties, and conducting studies at liquefaction sites related to the 1811-1812 and prehistoric New Madrid earthquakes. The seismic piezocone provides four independent measurements for delineating the stratigraphy, liquefaction potential, and site amplification parameters. At the same location, two independent assessments of soil liquefaction susceptibility can be made using both the normalized tip resistance (qc1N) and shear wave velocity (Vs1). In lieu of traditional deterministic approaches, the CPT data can be processed using probability curves to assess the level and likelihood of future liquefaction occurrence. ?? 2002 Elsevier Science Ltd. All rights reserved.

Combined hydrothermal liquefaction and catalytic hydrothermal gasification system and process for conversion of biomass feedstocks

DOEpatents

Elliott, Douglas C.; Neuenschwander, Gary G.; Hart, Todd R.

2017-09-12

A combined hydrothermal liquefaction (HTL) and catalytic hydrothermal gasification (CHG) system and process are described that convert various biomass-containing sources into separable bio-oils and aqueous effluents that contain residual organics. Bio-oils may be converted to useful bio-based fuels and other chemical feedstocks. Residual organics in HTL aqueous effluents may be gasified and converted into medium-BTU product gases and directly used for process heating or to provide energy.

Hybrid Technology of Hard Coal Mining from Seams Located at Great Depths

NASA Astrophysics Data System (ADS)

Czaja, Piotr; Kamiński, Paweł; Klich, Jerzy; Tajduś, Antoni

2014-10-01

Learning to control fire changed the life of man considerably. Learning to convert the energy derived from combustion of coal or hydrocarbons into another type of energy, such as steam pressure or electricity, has put him on the path of scientific and technological revolution, stimulating dynamic development. Since the dawn of time, fossil fuels have been serving as the mankind's natural reservoir of energy in an increasingly great capacity. A completely incomprehensible refusal to use fossil fuels causes some local populations, who do not possess a comprehensive knowledge of the subject, to protest and even generate social conflicts as an expression of their dislike for the extraction of minerals. Our times are marked by the search for more efficient ways of utilizing fossil fuels by introducing non-conventional technologies of exploiting conventional energy sources. During apartheid, South Africa demonstrated that cheap coal can easily satisfy total demand for liquid and gaseous fuels. In consideration of current high prices of hydrocarbon media (oil and gas), gasification or liquefaction of coal seems to be the innovative technology convergent with contemporary expectations of both energy producers as well as environmentalists. Known mainly from literature reports, underground coal gasification technologies can be brought down to two basic methods: - shaftless method - drilling, in which the gasified seam is uncovered using boreholes drilled from the surface, - shaft method, in which the existing infrastructure of underground mines is used to uncover the seams. This paper presents a hybrid shaft-drilling approach to the acquisition of primary energy carriers (methane and syngas) from coal seams located at great depths. A major advantage of this method is the fact that the use of conventional coal mining technology requires the seams located at great depths to be placed on the off-balance sheet, while the hybrid method of underground gasification enables them to become a source of additional energy for the economy. It should be noted, however, that the shaft-drilling method cannot be considered as an alternative to conventional methods of coal extraction, but rather as a complementary and cheaper way of utilizing resources located almost beyond the technical capabilities of conventional extraction methods due to the associated natural hazards and high costs of combating them. This article presents a completely different approach to the issue of underground coal gasification. Repurposing of the already fully depreciated mining infrastructure for the gasification process may result in a large value added of synthesis gas production and very positive economic effect.

Use of Molecular Modeling to Determine the Interaction and Competition of Gases within Coal for Carbon Dioxide Sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jeffrey D. Evanseck; Jeffry D. Madura

A 3-dimensional coal structural model for the Argonne Premium Coal Pocahontas No. 3 has been generated. The model was constructed based on the wealth of structural information available in the literature with the enhancement that the structural diversity within the structure was represented implicitly (for the first time) based on image analysis of HRTEM in combination with LDMS data. The complex and large structural model (>10,000 carbon atoms) will serve as a basis for examining the interaction of gases within this low volatile bituminous coal. Simulations are of interest to permit reasonable simulations of the host-guest interactions with regard tomore » carbon dioxide sequestration within coal and methane displacement from coal. The molecular structure will also prove useful in examining other coal related behavior such as solvent swelling, liquefaction and other properties. Molecular models of CO{sub 2} have been evaluated with water to analyze which classical molecular force-field parameters are the most reasonable to predict the interactions of CO{sub 2} with water. The comparison of the molecular force field models was for a single CO{sub 2}-H{sub 2}O complex and was compared against first principles quantum mechanical calculations. The interaction energies and the electrostatic interaction distances were used as criteria in the comparison. The ab initio calculations included Hartree-Fock, B3LYP, and Moeller-Plesset 2nd, 3rd, and 4th order perturbation theories with basis sets up to the aug-cc-pvtz basis set. The Steele model was the best literature model, when compared to the ab initio data, however, our new CO{sub 2} model reproduces the QM data significantly better than the Steele force-field model.« less

Thermodynamic design of natural gas liquefaction cycles for offshore application

NASA Astrophysics Data System (ADS)

Chang, Ho-Myung; Lim, Hye Su; Choe, Kun Hyung

2014-09-01

A thermodynamic study is carried out for natural gas liquefaction cycles applicable to offshore floating plants, as partial efforts of an ongoing governmental project in Korea. For offshore liquefaction, the most suitable cycle may be different from the on-land LNG processes under operation, because compactness and simple operation are important as well as thermodynamic efficiency. As a turbine-based cycle, closed Claude cycle is proposed to use NG (natural gas) itself as refrigerant. The optimal condition for NG Claude cycle is determined with a process simulator (Aspen HYSYS), and the results are compared with fully-developed C3-MR (propane pre-cooled mixed refrigerant) JT cycles and various N2 (nitrogen) Brayton cycles in terms of efficiency and compactness. The newly proposed NG Claude cycle could be a good candidate for offshore LNG processes.

Potential of soil liquefaction at Perlis, northern region of Malalysia

NASA Astrophysics Data System (ADS)

Ghazaly, Zuhayr Md; Rahim, Mustaqqim Abdul; Nasir, Mohamad Amzar Bin Mhd; Isa, Nur Fitriah; Zaki, Mohd Faiz Mohammad; Hassan, Zulkarnain Bin; Ismail, Zul-Atfi Bin

2017-09-01

Soil liquefaction is earthquake's secondary effect which could cause fatal damages and structures instability. Despite Malaysia been located in stable zone of Pacific Ring of Fire, few significant surrounded quakes like Sumatra-Andaman earthquake had prompted Malaysian's public concern, especially in Perlis area, on local seismic resistant. Hence, this research presents the analysis result of liquefaction potential of the soils, as the secondary effect of earthquake, within Perlis, northern region of Malaysia; the next strong and sustainable metropolis by using semi-empirical procedures introduced by Seed and Idriss. The study consists of two stages which were determination of the local geological and geotechnical site conditions within Perlis and analysis of soil liquefaction susceptibility by using various methods and liquefaction potential by using Simplified Procedure developed by Seed and Idriss on stress approach. There were consist of four phases implemented in order to achieve the objectives targeted for the study after problem being identified. Firstly, a comprehensive review of literature on liquefaction at Perlis was carried out. Second phase was data collection process that includes collection of Site Investigation (SI) report. Thirdly, data analysis was carried out by utilizing suitable method. The final phase was to draw conclusion and recommendation for this study. It can be concluded that the overall Perlis due to earthquake moment magnitude below 7.5 has no potential to soil liquefaction. However, with the range of liquefaction potential of 1.60 to 5.64 in Kuala Perlis area, it is liquefiable. The development of liquefaction severity map of Perlis, Malaysia in this research, may be used by others as a reference for seismic design and standard safety measures as well as for further research work.

Bench-scale research in biomass liquefaction in support of the Albany, Oregon experimental facility

NASA Astrophysics Data System (ADS)

Elliott, D. C.

1981-03-01

The liquefaction of solid materials (wood, newsprint, animal manure) by beating to produce useful liquid fuels was investigated. Highlights of work performed include: (1) catalyst mechanism studies; (2) analytical reports on TR8 and TR9 product oils; (3) liquid chromatography/mass spectroscopy analysis of wood oil; (4) batch conversion tests on bottom material; (5) vapor pressure studies; and (6) product evaluation. It was confirmed that the key process parameters and the effects of varying operating conditions are in support of biomass liquefaction.

Bio oil synthesis by coupling biological biomass pretreatment and catalytic hydroliquefaction process.

PubMed

Hamieh, S; Beauchet, R; Lemee, L; Toufaily, J; Koubaissy, B; Hamieh, T; Pouilloux, Y; Pinard, L

2014-03-01

The bio-oil synthesis from a mixture of wastes (7wt.% straw, 38wt.% wood, and 45wt.% grass) was carried out by direct liquefaction reaction using Raney Nickel as catalyst and tetralin as solvent. The green wastes were biologically degraded during 3 months. Longer the destructuration time; higher the yield into oil is. Biological pretreatment of green wastes promotes the liquefaction process. Among the components of degraded biomass, Humin, the major fraction (60-80wt.%) that was favored by the biological treatment, yields to a bio oil extremely energetic with a HHV close to biopetroleum (40MJ kg(-1)), contrariwise, Fulvic acids (2-12wt.%), the minor fraction is refractory to liquefaction reaction. Copyright © 2014 Elsevier Ltd. All rights reserved.

Direct Coal -to-Liquids (CTL) for Jet Fuel Using Biomass-Derived Solvents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chauhan, Satya P.; Garbark, Daniel B.; Taha, Rachid

Battelle has demonstrated a novel and potentially breakthrough technology for a direct coal-to-liquids (CTL) process for producing jet fuel using biomass-derived coal solvents (bio-solvents). The Battelle process offers a significant reduction in capital and operating costs and a substantial reduction in greenhouse gas (GHG) emissions, without requiring carbon capture and storage (CCS). The results of the project are the advancement of three steps of the hybrid coal/biomass-to-jet fuel process to the technology readiness level (TRL) of 5. The project objectives were achieved over two phases. In Phase 1, all three major process steps were explored and refined at bench-scale, including:more » (1) biomass conversion to high hydrogen-donor bio-solvent; (2) coal dissolution in biomass-derived bio-solvent, without requiring molecular H 2, to produce a synthetic crude (syncrude); and (3) two-stage catalytic hydrotreating/hydrogenation of syncrude to jet fuel and other distillates. In Phase 2, all three subsystems of the CTL process were scaled up to a pre-pilot scale, and an economic analysis was carried out. A total of over 40 bio-solvents were identified and prepared. The most unique attribute of Battelle’s bio-solvents is their ability to provide much-needed hydrogen to liquefy coal and thus increase its hydrogen content so much that the resulting syncrude is liquid at room temperature. Based on the laboratory-scale testing with bituminous coals from Ohio and West Virginia, a total of 12 novel bio-solvent met the goal of greater than 80% coal solubility, with 8 bio-solvents being as good as or better than a well-known but expensive hydrogen-donor solvent, tetralin. The Battelle CTL process was then scaled up to 1 ton/day (1TPD) at a pre-pilot facility operated in Morgantown, WV. These tests were conducted, in part, to produce enough material for syncrude-upgrading testing. To convert the Battelle-CTL syncrude into a form suitable as a blending stock for jet turbine fuel, a two-step catalytic upgrading process was developed at laboratory scale and then demonstrated at pre-pilot scale facility in Pittsburg, PA. Several drums of distillate products were produced, which were then distilled into unblended (neat) synthetic jet fuel and diesel products for a detailed characterization. Based on a detailed characterization of the synthetic jet fuel, a 20% synthetic, 80% commercial jet fuel blend was prepared, which met all specifications. An analysis of the synthetic diesel product showed that it has the promise of being a drop-in fuel as super-low (less than 15 ppm)-sulfur diesel fuel. A detailed economic analysis showed that the Battelle liquefaction process is economical at between 1000 metric tons/day (MT/day) and 2000 MT/day. The unit capital cost for Battelle CTL process for making jet fuel is 50K USD/daily bbl compared to 151K USD/daily bbl for indirect CTL, based on 2011 dollars. The jet-fuel selling cost at the refinery, including a 12% capital cost factor (which included profit), for the Battelle CTL process is 61USD/bbl (1.45 USD/gallon). This is competitive with crude oil price of 48 USD/bbl. At the same time, the GHG emissions of 3.56 MT CO 2/MT fuel were lower than the GHG emissions of 3.79 MT CO 2/MTfuel for petroleum-based fuels and 7.77 MT CO 2/MT fuel for indirect CTL. Thus, the use of bio-solvents completely eliminates the need for carbon capture in the case of Battelle CTL process. The superior economics and low GHG emissions for the Battelle CTL process has thus sparked worldwide interest and some potential commercialization opportunities are emerging.« less

Chemical engineering challenges and investment opportunities in sustainable energy.

PubMed

Heller, Adam

2008-01-01

The chemical and energy industries are transforming as they adjust to the new era of high-priced petroleum and severe global warming. As a result of the transformation, engineering challenges and investment opportunities abound. Rapid evolution and fast growth are expected in cathode and anode materials as well as polymeric electrolytes for vehicular batteries and in high-performance polymer-ceramic composites for wind turbines, fuel-efficient aircraft, and lighter and safer cars. Unique process-engineering opportunities exist in sand-oil, coal, and possibly also shale liquefaction to produce transportation fuel; and also in genetic engineering of photosynthesizing plants and other organisms for their processing into high-performance biodegradable polymers and high-value-added environmentally friendly chemicals. Also, research on the feasibility of mitigation of global warming through enhancement of CO(2) uptake by the southern oceans by fertilization with trace amounts of iron is progressing. Because chemical engineers are uniquely well trained in mathematical modeling of mass transport, flow, and mixing, and also in cost analysis, they are likely to join the oceanographers and marine biologists in this important endeavor.

Techno-economic Analysis of Acid Gas Removal and Liquefaction for Pressurized LNG

NASA Astrophysics Data System (ADS)

Lee, S. H.; Seo, Y. K.; Chang, D. J.

2018-05-01

This study estimated the life cycle cost (LCC) of an acid gas removal and a liquefaction processes for Pressurized LNG (PLNG) production and compared the results with the cost of normal LNG production. PLNG is pressurized LNG that is liquefied at a higher pressure and temperature than normal LNG. Due to the high temperature, the energy for liquefaction is reduced. The allowable CO2 concentration in PLNG is increased up to 3 mol% when the product pressure 25 bar. An amine process with 35 wt% of diethanolamine (DEA) aqueous solution and a nitrogen expansion cycle were selected for the acid gas removal and the liquefaction processes, respectively. Two types of CO2 concentration in the feed gas were investigated to analyze their impacts on the acid gas removal unit. When the CO2 concentration was 5 mol%, the acid gas removal unit was required for both LNG and PLNG production. However, the acid gas removal unit was not necessary in PLNG when the concentration was 0.5 mol% and the pressure was higher than 15 bar. The results showed that the LCC of PLNG was reduced by almost 35% relative to that of LNG when the PLNG pressure was higher than 15 bar.

Prediction of thermodynamic properties of coal derivatives. Progress report, September 1, 1981-August 31, 1982

DOE Office of Scientific and Technical Information (OSTI.GOV)

Donohue, M.D.

It is the purpose of this research program to develop a model to predict the thermodynamic properties of coal derivatives. Unlike natural gas and petroleum, coal and its gasification and liquefaction products are predominantly aromatic and have substantial quadrupole moments. Because of these quadrupole forces, the numerous correlational techniques that have been developed for petroleum products cannot be used to predict the thermodynamic properties of coal derivatives. We are presently developing a correlation that will be useful in predicting the thermodynamic properties of coal derivatives. This theory is based on the Perturbed-Hard-Chain theory, but is different from PHCT in twomore » respects. First, PHCT uses a square-well to describe the intermolecular potential energy between two molecules. In our new theory, the Lennard-Jones potential energy function is used. The second difference is that we take into account the effect of quadrupole forces on the intermolecular potential energy. In PHCT these forces were ignored. In PHCT the contributions to the partition function (or equation of state) that arise from the attractive forces between molecules (regardless of whether these forces are treated as a square-well or by Lennard-Jones) are calculated by assuming that they are perturbations on a hard sphere. In calculating the contributions to the partition function that arise from the quadrupole-quadrupole interactions, we use a second order perturbation about the Lennard-Jones. For aromatic molecules, the effect of this additional perturbation is significant.« less

Porous media deformation due to fluid flow: From hydrofracture formation to seismic liquefaction, a numerical and experimental study

NASA Astrophysics Data System (ADS)

Toussaint, R.; Turkaya, S.; Eriksen, F.; Clément, C.; Sanchez-Colina, G.; Maloy, K. J.; Flekkoy, E.; Aharonov, E.; Lengliné, O.; Daniel, G.; Altshuler, E.; Batista-Leyva, A.; Niebling, M.

2016-12-01

We present here the deformation of porous media in two different situations: 1. The formation of channels and fracture during pressurization of pore fluids, as happens during eruptions or injection of fluids and gas into soils and rocks. 2. The liquefaction of soils at different degrees of saturations during Earthquakes. The formation of channels during hydrofracture and pneumatic fractures is studied in laboratory experiments and in numerical models. The experiments are done on different types of porous media in Hele-Shaw cells, where fluid is injected at controlled overpressures, and various boundary conditions are used. Using fast cameras, we determine the strain and velocity fields from the images. We also record the characteristics of micro-seismic emissions during the process, and link this seismic record features and the direct image of the displacement responsible for the seismic sources in the medium. We also carry out numerical simulations, using coupled fluid/solid hydrid models that capture solid stress, pore pressure, solid and fluid elasticity - a full poro-elasto-plastic model using granular representation of the solid and a continuous one for the fluid.Next, Soil liquefaction is a significant natural hazard associated with earthquakes. Some of its devastating effects include tilting and sinking of buildings and bridges, and destruction of pipelines. Conventional geotechnical engineering assumes liquefaction occurs via elevated pore pressure. This assumption guides construction for seismically hazardous locations, yet evidence suggests that liquefaction strikes also under currently unpredicted conditions. We show, using theory, simulations and experiments, another mechanism for liquefaction in saturated soils, without high pore fluid pressure and without special soils, whereby liquefaction is controlled by buoyancy forces. This new mechanism enlarges the window of conditions under which liquefaction is predicted to occur, and may explain previously not understood cases such as liquefaction in well-compacted soils, under drained conditions, repeated liquefaction cases, far-field liquefaction and the basics of sinking in quicksand. These results may greatly impact hazard assessment and mitigation in seismically active areas.

Effect of hydrogen pressure on free radicals in direct coal liquefaction/coprocessing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seehra, M.S.; Ibrahim, M.M.

1995-12-31

The objective of this study was to investigate the coprocessing of coal with waste tires and commingled plastics and to characterize the relevant catalysts, using high pressure/high temperature in-situ ESR (Electron Spin Resonance) spectroscopy. The recent results from high pressure ESR spectroscopy are emphasized. During this period, considerable progress was made in developing the high pressure capabilities in in-situ ESR spectroscopy and new results carried out in 1000 psi of H{sub 2}gas are presented. In these experiments, sapphire tubes were used to contain the high pressures at temperatures up to 500{degrees}C. Results of the experiments carried out under 1000 psimore » of H{sub 2} are compared with those under 1000 psi of non-interacting argon and with the earlier experiments in flowing H{sub 2} gas where the volatiles are removed by the flowing gas. In these experiments, the free radical density N of the Blind Canyon coal was measured at each temperature and pressure by double integration of the ESR signal and calibrating it against a standard. The details of the experimental apparatus and procedures have been described in earlier publications.« less

Liquefaction of torrefied wood using microwave irradiation

Treesearch

Mengchao Zhou; Thomas Eberhardt; Pingping Xin; Chung-Yun Hse; Hui Pan

2016-01-01

Torrefaction is an effective pretreatment method to improve the uniformity and quality of lignocellulosic biomass before further thermal processing (e.g., gasification, combustion). The objective of this study was to determine the impacts of torrefaction as a pretreatment before liquefaction. Wood chips were torrefied for 2 h at three different temperatures (230, 260,...

Beneficial synergistic effect on bio-oil production from co-liquefaction of sewage sludge and lignocellulosic biomass.

PubMed

Leng, Lijian; Li, Jun; Yuan, Xingzhong; Li, Jingjing; Han, Pei; Hong, Yuchun; Wei, Feng; Zhou, Wenguang

2018-03-01

Co-liquefaction of municipal sewage sludge (MSS) and lignocellulosic biomass such as rice straw or wood sawdust at different mixing ratios and the characterization of the obtained bio-oil and bio-char were investigated. Synergistic effects were found during co-processing of MSS with biomass for production of bio-oil with higher yield and better fuel properties than those from individual feedstock. The co-liquefaction of MSS/rice straw (4/4, wt) increased the bio-oil yield from 22.74% (bio-oil yield from liquefaction of MSS individually) or 23.67% (rice straw) to 32.45%. Comparable increase on bio-oil yield was also observed for MSS/wood sawdust mixtures (2/6, wt). The bio-oils produced from MSS/biomass mixtures were mainly composed of esters and phenols with lower boiling points (degradation temperatures) than those from individual feedstock (identified with higher heavy bio-oil fractions). These synergistic effects were probably resulted from the interactions between the intermittent products of MSS and those of biomass during processing. Copyright © 2017 Elsevier Ltd. All rights reserved.

Nitrogen expander cycles for large capacity liquefaction of natural gas

NASA Astrophysics Data System (ADS)

Chang, Ho-Myung; Park, Jae Hoon; Gwak, Kyung Hyun; Choe, Kun Hyung

2014-01-01

Thermodynamic study is performed on nitrogen expander cycles for large capacity liquefaction of natural gas. In order to substantially increase the capacity, a Brayton refrigeration cycle with nitrogen expander was recently added to the cold end of the reputable propane pre-cooled mixed-refrigerant (C3-MR) process. Similar modifications with a nitrogen expander cycle are extensively investigated on a variety of cycle configurations. The existing and modified cycles are simulated with commercial process software (Aspen HYSYS) based on selected specifications. The results are compared in terms of thermodynamic efficiency, liquefaction capacity, and estimated size of heat exchangers. The combination of C3-MR with partial regeneration and pre-cooling of nitrogen expander cycle is recommended to have a great potential for high efficiency and large capacity.

Tandem mass spectrometry: analysis of complex mixtures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singleton, K.E.

1985-01-01

Applications of tandem mass spectrometry (MS/MS) for the analysis of complex mixtures results in increased specificity and selectivity by using a variety of reagent gases in both negative and positive ion modes. Natural isotopic abundance ratios were examined in both simple and complex mixtures using parent, daughter and neutral loss scans. MS/MS was also used to discover new compounds. Daughter scans were used to identify seven new alkaloids in a cactus species. Three of these alkaloids were novel compounds, and included the first simple, fully aromatic isoquinoline alkaloids reported in Cactaceae. MS/MS was used to characterize the chemical reaction productsmore » of coal in studies designed to probe its macromolecular structure. Negative ion chemical ionization was utilized to study reaction products resulting from the oxidation of coal. Possible structural units in the precursor coal were predicted based on the reaction products identified, aliphatic and aromatic acids and their anhydrides. The MS/MS method was also used to characterize reaction products resulting from coal liquefaction and/or extraction. These studies illustrate the types of problems for which MS/MS is useful. Emphasis has been placed on characterization of complex mixtures by selecting experimental parameters which enhance the information obtained. The value of using MS/MS in conjunction with other analytical techniques as well as the chemical pretreatment is demonstrated.« less

Chemistry and catalysis of coal liquefaction catalytic and thermal upgrading of coal liquid and hydrogenation of CO to produce fuels. Quarterly progress report, July-September 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiser, W.H.

1981-02-01

Studies on the basic properties of supported sulfide catalysts showed that different supports have a profound influence on catalytic activities of CoMo catalysts. The three functions of hydrodesulfurization, hydrogenation and cracking were differently affected depending on the support used and the manner of preparation of the catalyst. Also, incorporation of additives to the support showed that the different catalytic functions can be selectively affected. A systematic study concerned with catalytic cracking of coal-derived liquids, viz., an SRC-II middle-heavy distillate and four hydrotreated SRC-II products was carried out in the range of 375 to 500/sup 0/C (LHSV, 0.2 to 3.9 h/supmore » -1/). Hydrotreatment, even to a limited extent, results in a remarkable improvement in the yield of gasoline-range products from the SRC-II distillate. This improvement is ascribed to: (a) hydrogenolysis reactions leading to lower molecular weight feedstock components and (b) limited hydrogenation of aromatic rings leading to polycyclic feed components with sufficient concentration of hydroaromatic rings needed for effective cracking. The results with model compounds and the data on hydrogen consumption during hydrotreatment of SRC-II liquids indicate that for tricyclic, tetracyclic, and pentacyclic coal-liquid components the optimal concentration of hydroaromatic rings for effective subsequent cracking is at least two rings per molecule.« less

The latest developments and outlook for hydrogen liquefaction technology

NASA Astrophysics Data System (ADS)

Ohlig, K.; Decker, L.

2014-01-01

Liquefied hydrogen is presently mainly used for space applications and the semiconductor industry. While clean energy applications, for e.g. the automotive sector, currently contribute to this demand with a small share only, their demand may see a significant boost in the next years with the need for large scale liquefaction plants exceeding the current plant sizes by far. Hydrogen liquefaction for small scale plants with a maximum capacity of 3 tons per day (tpd) is accomplished with a Brayton refrigeration cycle using helium as refrigerant. This technology is characterized by low investment costs but lower process efficiency and hence higher operating costs. For larger plants, a hydrogen Claude cycle is used, characterized by higher investment but lower operating costs. However, liquefaction plants meeting the potentially high demand in the clean energy sector will need further optimization with regard to energy efficiency and hence operating costs. The present paper gives an overview of the currently applied technologies, including their thermodynamic and technical background. Areas of improvement are identified to derive process concepts for future large scale hydrogen liquefaction plants meeting the needs of clean energy applications with optimized energy efficiency and hence minimized operating costs. Compared to studies in this field, this paper focuses on application of new technology and innovative concepts which are either readily available or will require short qualification procedures. They will hence allow implementation in plants in the close future.

A new boil-off gas re-liquefaction system for LNG carriers based on dual mixed refrigerant cycle

NASA Astrophysics Data System (ADS)

Tan, Hongbo; Shan, Siyu; Nie, Yang; Zhao, Qingxuan

2018-06-01

A new boil-off gas (BOG) re-liquefaction system for LNG carriers has been proposed to improve the system energy efficiency. Two cascade mixed refrigerant cycles (or dual mixed refrigerant cycle, DMR) are used to provide the cooling capacity for the re-liquefaction of BOG. The performance of the new system is analysed on the basis of the thermodynamic data obtained in the process simulation in Aspen HYSYS software. The results show that the power consumed in the BOG compressor and the high-temperature mixed refrigerant compressor could be saved greatly due to the reduced mass flow rates of the processed fluids. Assuming the re-liquefaction capacity of the investigated system is 4557.6 kg/h, it is found that the total power consumption can be reduced by 25%, from 3444 kW in the existing system to 2585.8 kW in the proposed system. The coefficient of performance (COP) of 0.25, exergy efficiency of 41.3% and the specific energy consumption (SEC) of 0.589 kWh/kg(LNG) could be achieved in the new system. It exhibits 33% of improvement in the COP and exergy efficiency in comparison with the corresponding values of the existing system. It indicates that employing the DMR based BOG re-liquefaction system could improve the system energy efficiency of LNG carriers substantially.

Alkaline hydrothermal liquefaction of swine carcasses to bio-oil.

PubMed

Zheng, Ji-Lu; Zhu, Ming-Qiang; Wu, Hai-tang

2015-09-01

It is imperative that swine carcasses are disposed of safely, practically and economically. Alkaline hydrothermal liquefaction of swine carcasses to bio-oil was performed. Firstly, the effects of temperature, reaction time and pH value on the yield of each liquefaction product were determined. Secondly, liquefaction products, including bio-oil and solid residue, were characterized. Finally, the energy recovery ratio (ERR), which was defined as the energy of the resultant products compared to the energy input of the material, was investigated. Our experiment shows that reaction time had certain influence on the yield of liquefaction products, but temperature and pH value had bigger influence on the yield of liquefaction products. Yields of 62.2wt% bio-oil, having a high heating value of 32.35MJ/kg and a viscosity of 305cp, and 22wt% solid residue were realized at a liquefaction temperature of 250°C, a reaction time of 60min and a pH value of 9.0. The bio-oil contained up to hundreds of different chemical components that may be classified according to functional groups. Typical compound classes in the bio-oil were hydrocarbons, organic acids, esters, ketones and heterocyclics. The energy recovery ratio (ERR) reached 93.63%. The bio-oil is expected to contribute to fossil fuel replacement in stationary applications, including boilers and furnaces, and upgrading processes for the bio-oil may be used to obtain liquid transport fuels. Copyright © 2015 Elsevier Ltd. All rights reserved.

System and process for efficient separation of biocrudes and water in a hydrothermal liquefaction system

DOEpatents

Elliott, Douglas C.; Hart, Todd R.; Neuenschwander, Gary G.; Oyler, James R.; Rotness, Jr, Leslie J.; Schmidt, Andrew J.; Zacher, Alan H.

2016-08-02

A system and process are described for clean separation of biocrudes and water by-products from hydrothermal liquefaction (HTL) product mixtures of organic and biomass-containing feedstocks at elevated temperatures and pressures. Inorganic compound solids are removed prior to separation of biocrude and water by-product fractions to minimize formation of emulsions that impede separation. Separation may be performed at higher temperatures that reduce heat loss and need to cool product mixtures to ambient. The present invention thus achieves separation efficiencies not achieved in conventional HTL processing.

Effect of anatomical characteristics and chemical components on microwave-assisted liquefaction of bamboo wastes

Treesearch

JiuLong Xie; XingYan Huang; JinQiu Qi; Chung Hse; Todd Shupe

2014-01-01

The epidermis layer waste (ELW) and the inner layer waste (ILW) were removed from Phyllostachys pubescens bamboo, and the anatomical characteristics and chemical components of these wastes were comparatively investigated. Both the ELW and the ILW were subjected to a microwave-assisted liquefaction process to evaluate the relationship between bamboo...

Symbiotic Nuclear—Coal Systems for Production of Liquid Fuels

NASA Astrophysics Data System (ADS)

Taczanowski, S.

The notion of safety is not confined to the technological or non-proliferation aspects. It covers also the elements of energy policy: irrational reactions of societies, emotions, egoistic interests of more or less powerful pressure of economical and external political factors. One should be conscious that the country's privilege of being equipped by the Nature with rich resources of oil or gas is not solely economical, but even more a political one. Simultaneously, the gradual depletion of world hydrocarbons that draws behind irrevocable price increase has to be expected within the time scale of exploitation of power plants (now amounted to ~60 years). Therefore consequences of energy policy last much longer than the perspectives the political or economical decision makers are planning and acting within and the public is expecting successes and finally evaluating them. The world oil and gas resources are geopolitically very non-uniformly distributed, in contrast to coal and uranium. Since the level of energy self-sufficiency of the EU is highest for coal, the old idea of synfuels production from coal is recalled. Yet, in view of limits to the CO2 emissions in the EU another method has to be used here than the conventional coal liquefaction just applied in China. Simultaneously, an interesting evolution of energy prices was be observed, namely an increase in that of motor fuels in contrast to that of electricity remaining well stable. This fact suggests that the use of electricity (mainly the off-peak load), generated without emissions of CO2 for production of liquid fuels can prove reasonable. Thus, the essence of the presented idea of coal-nuclear symbiosis lies in the supply of energy in the form of H2, necessary for this process, from a nuclear reactor. Particularly, in the present option H2 is obtained by electrolytic water splitting supplying also O2 as a precious by-product in well mature and commercially available already since decades, Light Water Reactors (LWRs). The direct coal hydrogenation (Bergius method) has been proposed as the optimum process for liquid fuels production, as distinct by the best hydrogen economy, thus reducing the consumption of need nuclear energy. The present concept allows for simultaneous achievement of a number of aims: production of motor fuels without CO2 emissions (thus without carbon tax) based upon domestic energy carriers — coals, supply of the electricity produced in the nuclear power plant to the national grid to cover the peak demand. Such concept broadens the palette of liquid fuels supply, thus heightens energy safety of the country or e.g. whole of the EU. In an emergency case (for instance — disturbances of gas deliveries) the supply of produced H2 directly to the gas grid is also not excluded too. The performed preliminary cost evaluation indicates that the coal—nuclear symbiont can be well economic. Finally, the most radical option of coal-nuclear alliance is mentioned — the production of liquid fuels in the Fischer—Tropsch process from CO2 as a raw material sequestered from a coal power plant. The latter would use the oxy-combustion technique profiting on the O2 obtained earlier together with H2 what would facilitate the sequestration of CO2 at the plant. Unfortunately, this variant requires for reduction of CO2 to C much more hydrogen, achievable effectively in High Temperature Reactors commercially still unavailable. But on the basis of coal alone great resources — natural, technological and human of the coal sector can be best utilized too. Summarizing: the coal-nuclear synergy is the optimum far-sighted concept of safe development of the EU energy and fuels sector.

A thermodynamic review of cryogenic refrigeration cycles for liquefaction of natural gas

NASA Astrophysics Data System (ADS)

Chang, Ho-Myung

2015-12-01

A thermodynamic review is presented on cryogenic refrigeration cycles for the liquefaction process of natural gas. The main purpose of this review is to examine the thermodynamic structure of various cycles and provide a theoretical basis for selecting a cycle in accordance with different needs and design criteria. Based on existing or proposed liquefaction processes, sixteen ideal cycles are selected and the optimal conditions to achieve their best thermodynamic performance are investigated. The selected cycles include standard and modified versions of Joule-Thomson (JT) cycle, Brayton cycle, and their combined cycle with pure refrigerants (PR) or mixed refrigerants (MR). Full details of the cycles are presented and discussed in terms of FOM (figure of merit) and thermodynamic irreversibility. In addition, a new method of nomenclature is proposed to clearly identify the structure of cycles by abbreviation.

Process of producing liquid hydrocarbon fuels from biomass

DOEpatents

Kuester, James L.

1987-07-07

A continuous thermochemical indirect liquefaction process to convert various biomass materials into diesel-type transportation fuels which fuels are compatible with current engine designs and distribution systems comprising feeding said biomass into a circulating solid fluidized bed gasification system to produce a synthesis gas containing olefins, hydrogen and carbon monoxide and thereafter introducing the synthesis gas into a catalytic liquefaction system to convert the synthesis gas into liquid hydrocarbon fuel consisting essentially of C.sub.7 -C.sub.17 paraffinic hydrocarbons having cetane indices of 50+.

Liquefaction of corn stover and preparation of polyester from the liquefied polyol.

PubMed

Yu, Fei; Liu, Yuhuan; Pan, Xuejun; Lin, Xiangyang; Liu, Chengmei; Chen, Paul; Ruan, Roger

2006-01-01

This research investigated a novel process to prepare polyester from corn stover through liquefaction and crosslinking processes. First, corn stover was liquefied in organic solvents (90 wt% ethylene glycol and 10 wt% ethylene carbonate) with catalysts at moderate temperature under atmospheric pressure. The effect of liquefaction temperature, biomass content, and type of catalyst, such as H2SO4, HCl, H3PO4, and ZnCl2, was evaluated. Higher liquefaction yield was achieved in 2 wt% sulfuric acid, 1/4 (w/w) stover to liquefying reagent ratio; 160 degrees C temperature, in 2 h. The liquefied corn stover was rich in polyols, which can be directly used as feedstock for making polymers without further separation or purification. Second, polyester was made from the liquefied corn stover by crosslinking with multifunctional carboxylic acids and/or cyclic acid anhydrides. The tensile strength of polyester is about 5 MPa and the elongation is around 35%. The polyester is stable in cold water and organic solvents and readily biodegradable as indicated by 82% weight loss when buried in damp soil for 10 mo. The results indicate that this novel polyester could be used for the biodegradable garden mulch film production.

Use of liquefaction-induced features for paleoseismic analysis - An overview of how seismic liquefaction features can be distinguished from other features and how their regional distribution and properties of source sediment can be used to infer the location and strength of Holocene paleo-earthquakes

USGS Publications Warehouse

Obermeier, S.F.

1996-01-01

Liquefaction features can be used in many field settings to estimate the recurrence interval and magnitude of strong earthquakes through much of the Holocene. These features include dikes, craters, vented sand, sills, and laterally spreading landslides. The relatively high seismic shaking level required for their formation makes them particularly valuable as records of strong paleo-earthquakes. This state-of-the-art summary for using liquefaction-induced features for paleoseismic interpretation and analysis takes into account both geological and geotechnical engineering perspectives. The driving mechanism for formation of the features is primarily the increased pore-water pressure associated with liquefaction of sand-rich sediment. The role of this mechanism is often supplemented greatly by the direct action of seismic shaking at the ground surface, which strains and breaks the clay-rich cap that lies immediately above the sediment that liquefied. Discussed in the text are the processes involved in formation of the features, as well as their morphology and characteristics in field settings. Whether liquefaction occurs is controlled mainly by sediment grain size, sediment packing, depth to the water table, and strength and duration of seismic shaking. Formation of recognizable features in the field generally requires a low-permeability cap above the sediment that liquefied. Field manifestations are controlled largely by the severity of liquefaction and the thickness and properties of the low-permeability cap. Criteria are presented for determining whether observed sediment deformation in the field originated by seismically induced liquefaction. These criteria have been developed mainly by observing historic effects of liquefaction in varied field settings. The most important criterion is that a seismic liquefaction origin requires widespread, regional development of features around a core area where the effects are most severe. In addition, the features must have a morphology that is consistent with a very sudden application of a large hydraulic force. This article discusses case studies in widely separated and different geological settings: coastal South Carolina, the New Madrid seismic zone, the Wabash Valley seismic zone, and coastal Washington State. These studies encompass most of the range of settings and the types of liquefaction-induced features likely to be encountered anywhere. The case studies describe the observed features and the logic for assigning a seismic liquefaction origin to them. Also discussed are some types of sediment deformations that can be misinterpreted as having a seismic origin. Two independent methods for estimating prehistoric magnitude are discussed briefly. One method is based on determination of the maximum distance from the epicenter over which liquefaction-induced effects have formed. The other method is based on use of geotechnical engineering techniques at sites of marginal liquefaction, in order to bracket the peak accelerations as a function of epicentral distance; these accelerations can then be compared with predictions from seismological models.

The latest developments and outlook for hydrogen liquefaction technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ohlig, K.; Decker, L.

2014-01-29

Liquefied hydrogen is presently mainly used for space applications and the semiconductor industry. While clean energy applications, for e.g. the automotive sector, currently contribute to this demand with a small share only, their demand may see a significant boost in the next years with the need for large scale liquefaction plants exceeding the current plant sizes by far. Hydrogen liquefaction for small scale plants with a maximum capacity of 3 tons per day (tpd) is accomplished with a Brayton refrigeration cycle using helium as refrigerant. This technology is characterized by low investment costs but lower process efficiency and hence highermore » operating costs. For larger plants, a hydrogen Claude cycle is used, characterized by higher investment but lower operating costs. However, liquefaction plants meeting the potentially high demand in the clean energy sector will need further optimization with regard to energy efficiency and hence operating costs. The present paper gives an overview of the currently applied technologies, including their thermodynamic and technical background. Areas of improvement are identified to derive process concepts for future large scale hydrogen liquefaction plants meeting the needs of clean energy applications with optimized energy efficiency and hence minimized operating costs. Compared to studies in this field, this paper focuses on application of new technology and innovative concepts which are either readily available or will require short qualification procedures. They will hence allow implementation in plants in the close future.« less

Hydrodeoxygenation of coal using organometallic catalyst precursors

NASA Astrophysics Data System (ADS)

Kirby, Stephen R.

2002-04-01

The objective of this dissertation was to determine the desirability of organometallic compounds for the hydrodeoxygenation (HDO) of coal during liquefaction. The primary focus of this study was the removal of phenol-like compounds from coal liquids for the production of a thermally stable jet fuel. Investigation of the HDO ability of an organometallic compound containing both cobalt and molybdenum (CoMo-T2) was achieved using a combination of model compound and coal experiments. Model compounds were chosen representing four oxygen functional groups present in a range of coals. Electron density and bond order calculations were performed for anthrone, dinaphthyl ether, xanthene, di-t-butylmethylphenol, and some of their derivatives to ascertain a potential order of hydrogenolysis and hydrogenation reactivity for these compounds. The four model compounds were then reacted with CoMo-T2, as well as ammonium tetrathiomolybdate (ATTM). Products of reaction were grouped as compounds that had undergone deoxygenation, those that had aromatic rings reduced, those that were products of both reaction pathways, and those produced through other routes. ATTM had an affinity for both reaction types. Its reaction order for the four model compounds with respect to deoxygenated compounds was the same as that estimated from electron density calculations for hydrogenolysis reactivity. CoMo-T2 appeared to show a preference toward hydrogenation, although deoxygenated products were still achieved in similar, or greater, yields, for almost all the model compounds. The reactivity order achieved for the four compounds with CoMo-T2 was similar to that estimated from bond order calculations for hydrogenation reactivity. Three coals were selected representing a range of coal ranks and oxygen contents. DECS-26 (Wyodak), DECS-24 (Illinois #6), and DECS-23 (Pittsburgh #8) were analyzed by CPMAS 13C NMR and pyrolysis-GC-MS to determine the functional groups comprising the oxygen content of these coals. Trends within the data were similar to those reported by other authors. Based on the conclusions from both the model compound studies and the coal analysis, predictions were made of the catalyst precursors' performance in the HDO of the three selected coals. It was concluded that CoMo-T2 is a desirable catalyst precursor for the HDO of coals (particularly low-rank coals), but that an optimum set of conditions must be determined to take full advantage of its HDO ability. (Abstract shortened by UMI.)

Coal Quality and Major, Minor, and Trace Elements in the Powder River, Green River, and Williston Basins, Wyoming and North Dakota

USGS Publications Warehouse

Stricker, Gary D.; Flores, Romeo M.; Trippi, Michael H.; Ellis, Margaret S.; Olson, Carol M.; Sullivan, Jonah E.; Takahashi, Kenneth I.

2007-01-01

The U.S. Geological Survey (USGS), in cooperation with the Wyoming Reservoir Management Group (RMG) of the Bureau of Land Management (BLM) and nineteen independent coalbed methane (CBM) gas operators in the Powder River and Green River Basins in Wyoming and the Williston Basin in North Dakota, collected 963 coal samples from 37 core holes (fig. 1; table 1) between 1999 and 2005. The drilling and coring program was in response to the rapid development of CBM, particularly in the Powder River Basin (PRB), and the needs of the RMG BLM for new and more reliable data for CBM resource estimates and reservoir characterization. The USGS and BLM entered into agreements with the gas operators to drill and core Fort Union coal beds, thus supplying core samples for the USGS to analyze and provide the RMG with rapid, real-time results of total gas desorbed, coal quality, and high pressure methane adsorption isotherm data (Stricker and others, 2006). The USGS determined the ultimate composition of all coal core samples; for selected samples analyses also included proximate analysis, calorific value, equilibrium moisture, apparent specific gravity, and forms of sulfur. Analytical procedures followed those of the American Society of Testing Materials (ASTM; 1998). In addition, samples from three wells (129 samples) were analyzed for major, minor, and trace element contents. Ultimate and proximate compositions, calorific value, and forms of sulfur are fundamental parameters in evaluating the economic value of a coal. Determining trace element concentrations, along with total sulfur and ash yield, is also essential to assess the environmental effects of coal use, as is the suitability of the coal for cleaning, gasification, liquefaction, and other treatments. Determination of coal quality in the deeper part (depths greater than 1,000 to 1,200 ft) of the PRB (Rohrbacher and others, 2006; Luppens and others, 2006) is especially important, because these coals are targeted for future mining and development. This report contains summary tables, histograms, and isopleth maps of coal analyses. Details of the compositional internal variability of the coal beds are based on the continuous vertical sampling of coal sequences, including beds in the deeper part of the PRB. Such sampling allows for close comparisons of the compositions of different parts of coal beds as well as within the same coal beds at different core hole locations within short distances of each other.

Single temperature liquefaction process at different operating pHs to improve ethanol production from Indian rice and corn feedstock.

PubMed

Gohel, V; Ranganathan, K; Duan, G

2017-04-21

Conventional grain ethanol manufacturing is a high-temperature energy-intensive process comprising of multiple-unit operations when combined with lower ethanol recovery results in higher production cost. In liquefaction, jet cooking accounts for significant energy cost, while strong acid or base used for pH adjustment presents a safety hazard. A need is felt for sustainable ethanol manufacturing process that is less hazardous, consumes lower energy, and operates in a low pH range of 4.50-5.50. A single temperature liquefaction (STL) process that could efficiently operate at lower liquefaction temperature over a pH range of 4.50-5.50 was developed using rice and corn feedstock. Ethanol recovery witnessed at pH 4.5, 5.0, and 5.5 are 481.2 ± 1.5, 492.4 ± 1.5, and 493.6 ± 1.5 L MT -1 rice, respectively. Similarly, ethanol recovery witnessed at pH 4.5, 5.0, and 5.5 are 404.6 ± 1.3, 413.9 ± 0.8, and 412.4 ± 1.8 L MT -1 corn, respectively. The improvement in ethanol recovery is attributed to higher starch conversion by alpha-amylase even at pH as low as 4.50. Thus, the STL process operated at pH lower than 5.20 is poised to enhance sustainability by offering dual advantage of energy as well as chemical saving.

Publications of the Fossil Energy Advanced Research and Technology Development Materials Program: April 1, 1993-March 31, 1995

NASA Astrophysics Data System (ADS)

Carlson, Paul T.

1995-04-01

The objective of the Fossil Energy Advanced Research and Technology Development (AR and TD) Materials Program is to conduct research and development on materials for fossil energy applications, with a focus on the longer-term needs for materials with general applicability to the various fossil fuel technologies. The Program includes research aimed at a better understanding of materials behavior in fossil energy environments and on the development of new materials capable of substantial improvement in plant operations and reliability. The scope of the Program addresses materials requirements for all fossil energy systems, including materials for coal preparation, coal liquefaction, coal gasification, heat engines and heat recovery, combustion systems, and fuel cells. Work on the Program is conducted at national and government laboratories, universities, and industrial research facilities. This bibliography covers the period of April 1, 1993, through March 31, 1995, and is a supplement to previous bibliographies in this series. It is the intent of this series of bibliographies to list only those publications that can be conveniently obtained by a researcher through relatively normal channels. The publications listed in this document have been limited to topical reports, open literature publications in referred journals, full-length papers in published proceedings of conferences, full-length papers in unreferred journals, and books and book articles.

Complete liquefaction methods and apparatus

DOEpatents

Turner, Terry D.; Wilding, Bruce M.

2013-10-15

A method and apparatus are described to provide complete gas utilization in the liquefaction operation from a source of gas without return of natural gas to the source thereof from the process and apparatus. The mass flow rate of gas input into the system and apparatus may be substantially equal to the mass flow rate of liquefied product output from the system, such as for storage or use.

Wood liquefaction with phenol by microwave heating and FTIR evaluation

Treesearch

Gaiyun Li; Chungyun Hse; Tefu Qin

2015-01-01

We examined wood liquefaction using phenol and mixed acid catalysts with microwave heating, and compared that with similar processes that use oil bath heating. The reaction time for microwave heating to achieve a residue content was one sixth, one eighteenth, and one twenty-fourth of that from oil bath heating, respectively, for phenol to wood (P/W) ratios of 2.5/1, 2/...

Cryogenic hydrogen-induced air-liquefaction technologies for combined-cycle propulsion applications

NASA Technical Reports Server (NTRS)

Escher, William J. D.

1992-01-01

Given here is a technical assessment of the realization of cryogenic hydrogen induced air liquefaction technologies in a prospective onboard aerospace vehicle process setting. The technical findings related to the status of air liquefaction technologies are reviewed. Compact lightweight cryogenic heat exchangers, heat exchanger atmospheric constituent fouling alleviation measures, para/ortho-hydrogen shift-conversion catalysts, cryogenic air compressors and liquid air pumps, hydrogen recycling using slush hydrogen as a heat sink, liquid hydrogen/liquid air rocket-type combustion devices, and technically related engine concepts are discussed. Much of the LACE work is related to aerospaceplane propulsion concepts that were developed in the 1960's. Emphasis is placed on the Liquid Air Cycle Engine (LACE).

Mild Biomass Liquefaction Process for Economic Production of Stabilized Refinery-Ready Bio-oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gangwal, Santosh; Meng, Jiajia; McCabe, Kevin

Southern Research (SR) in cooperation with U.S. Department of Energy (DOE), Bioenergy Technology Office (BETO), investigated a biomass liquefaction process for economic production of stabilized refinery-ready bio-oil. The project was awarded by DOE under a Funding Opportunity Announcement (DE-FOA-0000686) for Bio-oil Stabilization and Commoditization that intended to evaluate the feasibility of using bio-oil as a potential feedstock in an existing petroleum refinery. SR investigated Topic Area 1 of the FOA at Technology Readiness Level 2-3 to develop thermochemical liquefaction technologies for producing a bio-oil feedstock from high-impact biomass that can be utilized within a petroleum refinery. Bio-oil obtained from fastmore » pyrolysis of biomass is a green intermediate that can be further upgraded into a biofuel for blending in a petroleum refinery using a hydro-deoxygenation (HDO) route. Co-processing pyrolysis bio-oil in a petroleum refinery is an attractive approach to leverage the refinery’s existing capital. However, the petroleum industry is reluctant to accept pyrolysis bio-oil because of a lack of a standard definition for an acceptable bio-oil feedstock in existing refinery processes. Also per BETO’s multiyear program plan, fast pyrolysis-based bio-fuel is presently not cost competitive with petroleum-based transportation fuels. SR aims to develop and demonstrate a cost-effective low-severity thermal liquefaction and hydrodeoxygenation (HDO) process to convert woody biomass to stabilized bio-oils that can be directly blended with hydrotreater input streams in a petroleum refinery for production of gasoline and/or diesel range hydrocarbons. The specific project objectives are to demonstrate the processes at laboratory scale, characterize the bio-oil product and develop a plan in partnership with a refinery company to move the technology towards commercialization.« less

Process of producing liquid hydrocarbon fuels from biomass

DOEpatents

Kuester, J.L.

1987-07-07

A continuous thermochemical indirect liquefaction process is described to convert various biomass materials into diesel-type transportation fuels which fuels are compatible with current engine designs and distribution systems comprising feeding said biomass into a circulating solid fluidized bed gasification system to produce a synthesis gas containing olefins, hydrogen and carbon monoxide and thereafter introducing the synthesis gas into a catalytic liquefaction system to convert the synthesis gas into liquid hydrocarbon fuel consisting essentially of C[sub 7]-C[sub 17] paraffinic hydrocarbons having cetane indices of 50+. 1 fig.

Alkaline hydrothermal liquefaction of swine carcasses to bio-oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zheng, Ji-Lu, E-mail: triace@163.com; Zhu, Ming-Qiang; Wu, Hai-tang

Highlights: • Swine carcasses can be converted to bio-oil by alkaline hydrothermal liquefaction. • It seems that the use of the bio-oil for heat or CHP is technically suitable. • Some valuable chemicals were found in the bio-oils. • The bio-oil and the solid residue constituted an energy efficiency of 93.63% for the feedstock. • The solid residue can be used as a soil amendment, to sequester C and for preparing activated carbon. - Abstract: It is imperative that swine carcasses are disposed of safely, practically and economically. Alkaline hydrothermal liquefaction of swine carcasses to bio-oil was performed. Firstly, themore » effects of temperature, reaction time and pH value on the yield of each liquefaction product were determined. Secondly, liquefaction products, including bio-oil and solid residue, were characterized. Finally, the energy recovery ratio (ERR), which was defined as the energy of the resultant products compared to the energy input of the material, was investigated. Our experiment shows that reaction time had certain influence on the yield of liquefaction products, but temperature and pH value had bigger influence on the yield of liquefaction products. Yields of 62.2 wt% bio-oil, having a high heating value of 32.35 MJ/kg and a viscosity of 305cp, and 22 wt% solid residue were realized at a liquefaction temperature of 250 °C, a reaction time of 60 min and a pH value of 9.0. The bio-oil contained up to hundreds of different chemical components that may be classified according to functional groups. Typical compound classes in the bio-oil were hydrocarbons, organic acids, esters, ketones and heterocyclics. The energy recovery ratio (ERR) reached 93.63%. The bio-oil is expected to contribute to fossil fuel replacement in stationary applications, including boilers and furnaces, and upgrading processes for the bio-oil may be used to obtain liquid transport fuels.« less

78 FR 62344 - Sabine Pass Liquefaction Expansion, LLC, Sabine Pass Liquefaction, LLC, and Sabine Pass LNG, L.P...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-18

.... CP13-553-000] Sabine Pass Liquefaction Expansion, LLC, Sabine Pass Liquefaction, LLC, and Sabine Pass... 30, 2013, Sabine Pass Liquefaction Expansion, LLC, Sabine Pass Liquefaction, LLC, and Sabine Pass LNG, L.P. (collectively referred to as Sabine Pass) filed with the Federal Energy Regulatory Commission...

Outlook for alternative energy sources. [aviation fuels

NASA Technical Reports Server (NTRS)

Card, M. E.

1980-01-01

Predictions are made concerning the development of alternative energy sources in the light of the present national energy situation. Particular emphasis is given to the impact of alternative fuels development on aviation fuels. The future outlook for aircraft fuels is that for the near term, there possibly will be no major fuel changes, but minor specification changes may be possible if supplies decrease. In the midterm, a broad cut fuel may be used if current development efforts are successful. As synfuel production levels increase beyond the 1990's there may be some mixtures of petroleum-based and synfuel products with the possibility of some shale distillate and indirect coal liquefaction products near the year 2000.

The NASA Hydrogen Energy Systems Technology study - A summary

NASA Technical Reports Server (NTRS)

Laumann, E. A.

1976-01-01

This study is concerned with: hydrogen use, alternatives and comparisons, hydrogen production, factors affecting application, and technology requirements. Two scenarios for future use are explained. One is called the reference hydrogen use scenario and assumes continued historic uses of hydrogen along with additional use for coal gasification and liquefaction, consistent with the Ford technical fix baseline (1974) projection. The expanded scenario relies on the nuclear electric economy (1973) energy projection and assumes the addition of limited new uses such as experimental hydrogen-fueled aircraft, some mixing with natural gas, and energy storage by utilities. Current uses and supply of hydrogen are described, and the technological requirements for developing new methods of hydrogen production are discussed.

Isolation and characterization of cellulose nanofibers from bamboo using microwave liquefaction combined with chemical treatment and ultrasonication.

PubMed

Xie, Jiulong; Hse, Chung-Yun; De Hoop, Cornelis F; Hu, Tingxing; Qi, Jinqiu; Shupe, Todd F

2016-10-20

Cellulose nanofibers were successfully isolated from bamboo using microwave liquefaction combined with chemical treatment and ultrasonic nanofibrillation processes. The microwave liquefaction could eliminate almost all the lignin in bamboo, resulting in high cellulose content residues within 7min, and the cellulose enriched residues could be readily purified by subsequent chemical treatments with lower chemical charging and quickly. The results of wet chemistry analyses, SEM images, and FTIR and X-ray spectra indicated the combination of microwave liquefaction and chemical treatment was significantly efficient in removing non-cellulosic compounds. Ultrasonication was used to separate the nanofibrils from the purified residues to extract nanofibers. The TEM images confirmed the presence of elementary fibrils, nano-sized fibril bundles, and aggregated fibril bundles. As evidenced by the TGA analysis, cellulose nanofibers isolated by this novel technique had high thermal stability indicating that the isolated nanofibers could possibly be applied as reinforcing elements in biomaterials. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of inhalation exposure to SRC-II heavy and middle distillates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Springer, D.L.; Miller, R.A.; Weimer, W.C.

1984-11-01

To expand the data base on potential health effects of coal liquefaction materials, we have performed studies with both solvent refined coal (SRC)-II heavy distillate (HD) and middle distillate (MD). Weight gain for exposed animals was less than that of controls and was dose-related, ranging from no significant difference for animals in the low-exposure group to failure to gain in the high-dose animals. Liver weights increased significantly over controls, and thymus weights decreased for animals sacrificed at 5 and 13 weeks. After both exposure periods, there were significant treatment-related decreases in erythrocyte parameters and in certain types of white bloodmore » cells (WBC). Bone marrow cellularity, and numbers of megakaryocytes consistently decreased, suggesting that bone marrow is a target tissue for high-boiling coal liquids. Microscopic evaluation of tissue indicated exposure-related changes is listed. In contrast to the reported mutagenic and carcinogenic effects observed for the high-boiling coal liquids, middle-boiling-range materials lacked such activity in these assays. These data demonstrate a great deal of similarity in the kinds of effects observed following exposure to middle- and high-boiling-range coal liquids. However, the significance of changes in organ weights and peripheral blood parameters are not always readily apparent following a subchronic study. Because of this, we exposed animals to HD in a manner similar to that for the subchronic experiment and have followed these animals throughout their lives for the development of adverse effects such as reduced longevity and the appearance of tumors. Results from this study will be available for mice in FY 1985 and for rats in FY 1986.« less

Semi-automated landform classification for hazard mapping of soil liquefaction by earthquake

NASA Astrophysics Data System (ADS)

Nakano, Takayuki

2018-05-01

Soil liquefaction damages were caused by huge earthquake in Japan, and the similar damages are concerned in near future huge earthquake. On the other hand, a preparation of soil liquefaction risk map (soil liquefaction hazard map) is impeded by the difficulty of evaluation of soil liquefaction risk. Generally, relative soil liquefaction risk should be able to be evaluated from landform classification data by using experimental rule based on the relationship between extent of soil liquefaction damage and landform classification items associated with past earthquake. Therefore, I rearranged the relationship between landform classification items and soil liquefaction risk intelligibly in order to enable the evaluation of soil liquefaction risk based on landform classification data appropriately and efficiently. And I developed a new method of generating landform classification data of 50-m grid size from existing landform classification data of 250-m grid size by using digital elevation model (DEM) data and multi-band satellite image data in order to evaluate soil liquefaction risk in detail spatially. It is expected that the products of this study contribute to efficient producing of soil liquefaction hazard map by local government.

Hydrothermal liquefaction of microalgae to produce biofuels: state of the art and future prospects

NASA Astrophysics Data System (ADS)

Vlaskin, M. S.; Chernova, N. I.; Kiseleva, S. V.; Popel', O. S.; Zhuk, A. Z.

2017-09-01

The article presents a review of the state of the art and lines of research on hydrothermal liquefaction (HTL) of microalgae (MA). The main advantages of this technology for production of biofuel are that it does not require predrying of the feedstock and ensures a relatively high product yield—the ratio of the end product weight to the feedstock weight—owing to the fact that all the microalgal components, viz., lipids, proteins, and carbohydrates, are converted into biofuel. MA hydrothermal liquefaction is considered to be a promising technology for conversion of biomass and is a subject of a series of research studies and, judging by the available publications, the scope of research in this field is expanding currently. However, many significant problems remain unsolved. In particular, an active searched is being conducted for suitable strains that will ensure not only a high lipid yield—necessary to convert microalgae into biodiesel—but also higher biomass productivity and a higher biofuel yield; the chemical reactions that occur during the hydrothermal treatment are being studied; and the effect of significant process variables, such as temperature, heating rate, holdup time at the maximum temperature, biomass concentration in the water suspension, biochemical and elemental compositions of the microalgae, use of catalysts, etc., on the liquefaction processes is being studied. One of the urgent tasks is also the reduction of the nitrogen content in the resulting biofuel. Studies aimed at the development of a continuous process and rational heat-processing plants for thermal microalgal conversion are being conducted to increase the energy efficiency of the HTL process, in particular, to provide the heat recovery and separation of the end product.

Quantitative characterization of the aqueous fraction from hydrothermal liquefaction of algae

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maddi, Balakrishna; Panisko, Ellen; Wietsma, Thomas

Aqueous streams generated from hydrothermal liquefaction contain approximately 30% of the total carbon present from the algal feed. Hence, this aqueous carbon must be utilized to produce liquid fuels and/or specialty chemicals for economic sustainability of hydrothermal liquefaction on industrial scale. In this study, aqueous fractions produced from the hydrothermal liquefaction of fresh water and saline water algal cultures were analyzed using a wide variety of analytical instruments to determine their compositional characteristics. This study will also inform researchers designing catalysts for down-stream processing such as high-pressure catalytic conversion of organics in aqueous phase, catalytic hydrothermal gasification, and biological conversions.more » Organic chemical compounds present in all eight aqueous fractions were identified using two-dimensional gas chromatography equipped with time-of-flight mass spectrometry. Identified compounds include organic acids, nitrogen compounds and aldehydes/ketones. Conventional gas chromatography and liquid chromatography methods were utilized to quantify the identified compounds. Inorganic species in the aqueous stream of hydrothermal liquefaction of algae were identified using ion chromatography and inductively coupled plasma optical emission spectrometer. The concentrations of organic chemical compounds and inorganic species are reported. The amount quantified carbon ranged from 45 to 72 % of total carbon in the aqueous fractions.« less

Liquefaction, flow, and associated ground failure

USGS Publications Warehouse

Youd, T. Leslie

1973-01-01

Ambiguities in the use of the term liquefaction and in defining the relation between liquefaction and ground failure have led to encumbered communication between workers in various fields and between specialists in the same field, and the possibility that evaluations of liquefaction potential could be misinterpreted or misapplied. Explicit definitions of liquefaction and related concepts are proposed herein. These definitions, based on observed laboratory behavior, are then used to clarify the relation between liquefaction and ground failure. Soil liquefaction is defined as the transformation of a granular material from a solid into a liquefied state as a consequence of increased pore-water pressures. This definition avoids confusion between liquefaction and possible flow-failure conditions after liquefaction. Flow-failure conditions are divided into two types: (1) unlimited flow if pore-pressure reductions caused by dilatancy during flow deformation are not sufficient to solidify the material and thus arrest flow, and (2) limited flow if they are sufficient to solidify the material after a finite deformation. After liquefaction in the field, unlimited flow commonly leads to flow landslides, whereas limited flow leads at most to lateral-spreading landslides. Quick-condition failures such as loss of bearing capacity form a third type of ground failure associated with liquefaction.

Regional liquefaction hazard evaluation following the 2010-2011 Christchurch (New Zealand) earthquake sequence

NASA Astrophysics Data System (ADS)

Begg, John; Brackley, Hannah; Irwin, Marion; Grant, Helen; Berryman, Kelvin; Dellow, Grant; Scott, David; Jones, Katie; Barrell, David; Lee, Julie; Townsend, Dougal; Jacka, Mike; Harwood, Nick; McCahon, Ian; Christensen, Steve

2013-04-01

Following the damaging 4 Sept 2010 Mw7.1 Darfield Earthquake, the 22 Feb 2011 Christchurch Earthquake and subsequent damaging aftershocks, we completed a liquefaction hazard evaluation for c. 2700 km2 of the coastal Canterbury region. Its purpose was to distinguish at a regional scale areas of land that, in the event of strong ground shaking, may be susceptible to damaging liquefaction from areas where damaging liquefaction is unlikely. This information will be used by local government for defining liquefaction-related geotechnical investigation requirements for consent applications. Following a review of historic records of liquefaction and existing liquefaction assessment maps, we undertook comprehensive new work that included: a geologic context from existing geologic maps; geomorphic mapping using LiDAR and integrating existing soil map data; compilation of lithological data for the surficial 10 m from an extensive drillhole database; modelling of depth to unconfined groundwater from existing subsurface and surface water data. Integrating and honouring all these sources of information, we mapped areas underlain by materials susceptible to liquefaction (liquefaction-prone lithologies present, or likely, in the near-surface, with shallow unconfined groundwater) from areas unlikely to suffer widespread liquefaction damage. Comparison of this work with more detailed liquefaction susceptibility assessment based on closely spaced geotechnical probes in Christchurch City provides a level of confidence in these results. We tested our susceptibility map by assigning a matrix of liquefaction susceptibility rankings to lithologies recorded in drillhole logs and local groundwater depths, then applying peak ground accelerations for four earthquake scenarios from the regional probabilistic seismic hazard model (25 year return = 0.13g; 100 year return = 0.22g; 500 year return = 0.38g and 2500 year return = 0.6g). Our mapped boundary between liquefaction-prone areas and areas unlikely to sustain heavy damage proved sound. In addition, we compared mapped liquefaction extents (derived from post-earthquake aerial photographs) from the 4 Sept 2010 Mw7.1 and 22 Feb 2011 Mw6.2 earthquakes with our liquefaction susceptibility map. The overall area of liquefaction for these two earthquakes was similar, and statistics show that for the first (large regional) earthquake, c. 93% of mapped liquefaction fell within the liquefaction-prone area, and for the second (local, high peak ground acceleration) earthquake, almost 99% fell within the liquefaction-prone area. We conclude that basic geological and groundwater data when coupled with LiDAR data can usefully delineate areas susceptible to liquefaction from those unlikely to suffer damaging liquefaction. We believe that these techniques can be used successfully in many other cities around the world.

Bio-oil production via subcritical hydrothermal liquefaction of biomass

NASA Astrophysics Data System (ADS)

Durak, Halil

2017-04-01

Biomass based raw materials can be converted into the more valued energy forms using biochemical methods such as ethanol fermentation, methane fermentation and the thermochemical methods such as direct combustion, pyrolysis, gasification, liquefaction. The bio-oil obtained from the biomass has many advantages than traditional use. Firstly, it has features such as high energy density, easy storage and easy transportation. Bio-oil can be used as a fuel in engines, turbines and burning units directly. Besides, it can be converted into products in higher quality and volume via catalytic cracking, hydrodexygenation, emulsification, and steam reforming [1,2]. Many organic solvents such as acetone, ethanol, methanol, isopropanol are used in the supercritical liquefaction processes. When we think about the cost and effects of the organic solvent on nature, it will be understood better that it is necessary to find solvent that are more sensitive against nature. Here, water must have an important place because of its features. Most important solvent of the world water is named as "universal solvent" because none of the liquids can dissolve the materials as much as done by water. Water is found much at the nature and cost of it is very few when compared with the other solvent. Hydrothermal liquefaction, a thermochemical conversion process is an effective method used for converting biomass into the liquid products. General reaction conditions for hydrothermal liquefaction process are the 250-374 °C temperature range and 4 - 22 Mpa pressure values range, besides, the temperature values can be higher according to the product that is expected to be obtained [3,4]. In this study, xanthium strumarium plant stems have been used as biomass source. The experiments have been carried out using a cylindrical reactor (75 mL) at the temperatures of 300 °C. The produced liquids at characterized by elemental analysis, GC-MS and FT-IR. According to the analysis, different types of compounds were identified by GC-MS.

Coupling hydrothermal liquefaction and anaerobic digestion for energy valorization from model biomass feedstocks.

PubMed

Posmanik, Roy; Labatut, Rodrigo A; Kim, Andrew H; Usack, Joseph G; Tester, Jefferson W; Angenent, Largus T

2017-06-01

Hydrothermal liquefaction converts food waste into oil and a carbon-rich hydrothermal aqueous phase. The hydrothermal aqueous phase may be converted to biomethane via anaerobic digestion. Here, the feasibility of coupling hydrothermal liquefaction and anaerobic digestion for the conversion of food waste into energy products was examined. A mixture of polysaccharides, proteins, and lipids, representing food waste, underwent hydrothermal processing at temperatures ranging from 200 to 350°C. The anaerobic biodegradability of the hydrothermal aqueous phase was examined through conducting biochemical methane potential assays. The results demonstrate that the anaerobic biodegradability of the hydrothermal aqueous phase was lower when the temperature of hydrothermal processing increased. The chemical composition of the hydrothermal aqueous phase affected the anaerobic biodegradability. However, no inhibition of biodegradation was observed for most samples. Combining hydrothermal and anaerobic digestion may, therefore, yield a higher energetic return by converting the feedstock into oil and biomethane. Copyright © 2017 Elsevier Ltd. All rights reserved.

Techno-economic feasibility and life cycle assessment of dairy effluent to renewable diesel via hydrothermal liquefaction.

PubMed

Summers, Hailey M; Ledbetter, Rhesa N; McCurdy, Alex T; Morgan, Michael R; Seefeldt, Lance C; Jena, Umakanta; Hoekman, S Kent; Quinn, Jason C

2015-11-01

The economic feasibility and environmental impact is investigated for the conversion of agricultural waste, delactosed whey permeate, through yeast fermentation to a renewable diesel via hydrothermal liquefaction. Process feasibility was demonstrated at laboratory-scale with data leveraged to validate systems models used to perform industrial-scale economic and environmental impact analyses. Results show a minimum fuel selling price of $4.78 per gallon of renewable diesel, a net energy ratio of 0.81, and greenhouse gas emissions of 30.0g-CO2-eqMJ(-1). High production costs and greenhouse gas emissions can be attributed to operational temperatures and durations of both fermentation and hydrothermal liquefaction. However, high lipid yields of the yeast counter these operational demands, resulting in a favorable net energy ratio. Results are presented on the optimization of the process based on economy of scale and a sensitivity analysis highlights improvements in conversion efficiency, yeast biomass productivity and hydrotreating efficiency can dramatically improve commercial feasibility. Copyright © 2015 Elsevier Ltd. All rights reserved.

A study of the efficiency of hydrogen liquefaction

NASA Technical Reports Server (NTRS)

Baker, C. R.; Shaner, R. L.

1976-01-01

The use of liquid hydrogen as a jet aircraft fuel has a number of environmental and technological advantages over conventional fuels. The liquefaction of hydrogen requires a large expenditure of energy. There are many inefficiencies that are a part of any practical liquefaction process. Current technology was investigated for the best available system. Parametric studies were made to identify where inefficiencies occur and to optimize and integrate the component parts. Flowsheets are presented for a module that produces 250 tons per day of liquid hydrogen. Approximately ten of these modules is needed for a major airport in the 1990's. The advantages of producing a product with a minimum amount of ortho to para hydrogen conversion are pointed out. The optimum degree of conversion was determined for a liquid hydrogen product that will be used within a given time. An assessment was made regarding the potentials for improvement of the processing schemes and equipment over the next 10 to 25 years.

Economically viable large-scale hydrogen liquefaction

NASA Astrophysics Data System (ADS)

Cardella, U.; Decker, L.; Klein, H.

2017-02-01

The liquid hydrogen demand, particularly driven by clean energy applications, will rise in the near future. As industrial large scale liquefiers will play a major role within the hydrogen supply chain, production capacity will have to increase by a multiple of today’s typical sizes. The main goal is to reduce the total cost of ownership for these plants by increasing energy efficiency with innovative and simple process designs, optimized in capital expenditure. New concepts must ensure a manageable plant complexity and flexible operability. In the phase of process development and selection, a dimensioning of key equipment for large scale liquefiers, such as turbines and compressors as well as heat exchangers, must be performed iteratively to ensure technological feasibility and maturity. Further critical aspects related to hydrogen liquefaction, e.g. fluid properties, ortho-para hydrogen conversion, and coldbox configuration, must be analysed in detail. This paper provides an overview on the approach, challenges and preliminary results in the development of efficient as well as economically viable concepts for large-scale hydrogen liquefaction.

High-quality fuel from food waste - investigation of a stepwise process from the perspective of technology development.

PubMed

Yin, Ke; Li, Ling; Giannis, Apostolos; Weerachanchai, Piyarat; Ng, Bernard J H; Wang, Jing-Yuan

2017-07-01

A stepwise process (SP) was developed for sustainable energy production from food waste (FW). The process comprised of hydrothermal treatment followed by oil upgrading. Synthetic food waste was primarily used as feedstock in the hydrothermal reactor under subcritical water conditions. The produced hydrochars were analyzed for calorific value (17.0-33.7 MJ/kg) and elemental composition indicating high-quality fuel comparable to coal. Hydrothermal carbonization (e.g. 180°C) would be efficient for oil recovery (>90%) from FW, as compared to hydrothermal liquefaction (320°C) whereby lipid degradation may take place. The recovered oil was upgraded to biodiesel in a catalytic refinery process. Selected biodiesels, that is, B3 and B4 were characterized for density (872.7 and 895.5 kg/m 3 ), kinematic viscosity (3.115 and 8.243 cSt), flash and pour point (30°C and >126°C), micro carbon (0.03% and 0.04%), sulfur (both <0.0016%), and calorific value (38,917 and 39,584 J/g), suggesting similar quality to commercial biodiesel. Fatty acid methyl ethers content was further analyzed to assess the influence of hydrothermal treatment in biodiesel quality, indicating the limited impacts. Overall, the SP provides a promising alternative for sustainable energy recovery through high-quality biofuel and hydrochar production.

Fractional Multistage Hydrothermal Liquefaction of Biomass and Catalytic Conversion into Hydrocarbons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cortright, Randy; Rozmiarek, Robert; Dally, Brice

2017-08-31

The objective of this project was to develop an improved multistage process for the hydrothermal liquefaction (HTL) of biomass to serve as a new front-end, deconstruction process ideally suited to feed Virent’s well-proven catalytic technology, which is already being scaled up. This process produced water soluble, partially de-oxygenated intermediates that are ideally suited for catalytic finishing to fungible distillate hydrocarbons. Through this project, Virent, with its partners, demonstrated the conversion of pine wood chips to drop-in hydrocarbon distillate fuels using a multi-stage fractional conversion system that is integrated with Virent’s BioForming® process. The majority of work was in the liquefactionmore » task and included temperature scoping, solvent optimization, and separations.« less

Recognizing and dating prehistoric liquefaction features: Lessons learned in the New Madrid seismic zone, central United States

USGS Publications Warehouse

Tuttle, M.P.; Schweig, E.S.

1996-01-01

The New Madrid seismic zone (NMSZ), which experienced severe liquefaction during the great New Madrid, Missouri, earthquakes of 1811 and 1812 as well as during several prehistoric earthquakes, is a superb laboratory for the study of world-class, arthquake-induced liquefaction features and their use in paleoseismology. In seismically active regions like the NMSZ, frequent large earthquakes can produce a complex record of liquefaction events that is difficult to interpret. Lessons learned studying liquefaction features in the NMSZ may help to unravel the paleoseismic record in other seismically active regions. Soil characteristics of liquefaction features, as well as their structural and sratigraphic relations to Native American occupation horizons and other cultural features, an help to distinguish prehistoric liquefaction features from historic features. In addition, analyses of artifact assemblages and botanical content of cultural horizons can help to narrow the age ranges of liquefaction features. Future research should focus on methods for defining source areas and estimating magnitudes of prehistoric earthquakes from liquefaction features. Also, new methods for dating liquefaction features are needed.

Anaerobic digestion of post-hydrothermal liquefaction wastewater for improved energy efficiency of hydrothermal bioenergy processes.

PubMed

Zhou, Yan; Schideman, Lance; Zheng, Mingxia; Martin-Ryals, Ana; Li, Peng; Tommaso, Giovana; Zhang, Yuanhui

2015-01-01

Hydrothermal liquefaction (HTL) is a promising process for converting wet biomass and organic wastes into bio-crude oil. It also produces an aqueous product referred to as post-hydrothermal liquefaction wastewater (PHWW) containing up to 40% of the original feedstock carbon, which reduces the overall energy efficiency of the HTL process. This study investigated the feasibility of using anaerobic digestion (AD) to treat PHWW, with the aid of activated carbon. Results showed that successful AD occurred at relatively low concentrations of PHWW (≤ 6.7%), producing a biogas yield of 0.5 ml/mg CODremoved, and ∼53% energy recovery efficiency. Higher concentrations of PHWW (≥13.3%) had an inhibitory effect on the AD process, as indicated by delayed, slower, or no biogas production. Activated carbon was shown to effectively mitigate this inhibitory effect by enhancing biogas production and allowing digestion to proceed at higher PHWW concentrations (up to 33.3%), likely due to sequestering toxic organic compounds. The addition of activated carbon also increased the net energy recovery efficiency of AD with a relatively high concentration of PHWW (33.3%), taking into account the energy for producing activated carbon. These results suggest that AD is a feasible approach to treat PHWW, and to improve the energy efficiency of the HTL processes.

Comparison of Oxygen Liquefaction Methods for Use on the Martian Surface

NASA Technical Reports Server (NTRS)

Johnson, W. L.; Hauser, D. M.; Plachta, D. W.; Wang, X-Y. J.; Banker, B. F.; Desai, P. S.; Stephens, J. R.; Swanger, A. M.

2017-01-01

In order to use oxygen that is produced on the surface of Mars from In-Situ production processes in a chemical propulsion system, the oxygen must first be converted from vapor phase to liquid phase and then stored within the propellant tanks of the propulsions system. There are multiple ways that this can be accomplished, from simply attaching a liquefaction system onto the propellant tanks to carrying separate tanks for liquefaction and storage of the propellant and loading just prior to launch (the way that traditional rocket launches occur on earth). A study was done into these various methods by which the oxygen (and methane) could be liquefied and stored on the Martian surface. Five different architectures or cycles were considered: Tube-on-Tank (also known as Broad Area Cooling or Distributed Refrigeration), Tube-in-Tank (also known as Integrated Refrigeration and Storage), a modified Linde open liquefaction/refrigeration cycle, the direct mounting of a pulse tube cryocooler onto the tank, and an in-line liquefier at ambient pressure. Models of each architecture were developed to give insight into the performance and losses of each of the options. The results were then compared across eight categories: Mass, Power (both input and heat rejection), Operability, Cost, Manufacturability, Reliability, Volumility, and Scalability. The result was that, given the current state of technology maturity, Tube-on-Tank architectures were the most attractive solution, closely followed by Tube-in-Tank. As a result of this technical analysis and other factors, NASA has determined to focus its Martian surface liquefaction activities and technology development on Tube-on-Tank liquefaction cycles.

Comparison of oxygen liquefaction methods for use on the Martian surface

NASA Astrophysics Data System (ADS)

Johnson, W. L.; Hauser, D. M.; Plachta, D. W.; Wang, X.-Y. J.; Banker, B. F.; Desai, P. S.; Stephens, J. R.; Swanger, A. M.

2018-03-01

In order to use oxygen that is produced on the surface of Mars from In-Situ production processes in a chemical propulsion system, the oxygen must first be converted from vapor phase to liquid phase and then stored within the propellant tanks of the propulsions system. There are multiple ways that this can be accomplished, from simply attaching a liquefaction system onto the propellant tanks to carrying separate tanks for liquefaction and storage of the propellant and loading just prior to launch (the way that traditional rocket launches occur on Earth). A study was done into these various methods by which the oxygen (and methane) could be liquefied and stored on the Martian surface. Five different architectures or cycles were considered: Tube-on-Tank (also known as Broad Area Cooling or Distributed Refrigeration), Tube-in-Tank (also known as Integrated Refrigeration and Storage), a modified Linde open liquefaction/refrigeration cycle, the direct mounting of a pulse tube cryocooler onto the tank, and an in-line liquefier at ambient pressure. Models of each architecture were developed to give insight into the performance and losses of each of the options. The results were then compared across eight categories: Mass, Power (both input and heat rejection), Operability, Cost, Manufacturability, Reliability, Volume-ility, and Scalability. The result was that Tube-on-Tank and Tube-in-Tank architectures were the most attractive solutions, with NASA's engineering management choosing to pursue tube on tank development rather than further differentiate the two. As a result NASA is focusing its Martian surface liquefaction activities and technology development on Tube-on-Tank liquefaction cycles.

Improvements on mapping soil liquefaction at a regional scale

NASA Astrophysics Data System (ADS)

Zhu, Jing

Earthquake induced soil liquefaction is an important secondary hazard during earthquakes and can lead to significant damage to infrastructure. Mapping liquefaction hazard is important in both planning for earthquake events and guiding relief efforts by positioning resources once the events have occurred. This dissertation addresses two aspects of liquefaction hazard mapping at a regional scale including 1) predictive liquefaction hazard mapping and 2) post-liquefaction cataloging. First, current predictive hazard liquefaction mapping relies on detailed geologic maps and geotechnical data, which are not always available in at-risk regions. This dissertation improves the predictive liquefaction hazard mapping by the development and validation of geospatial liquefaction models (Chapter 2 and 3) that predict liquefaction extent and are appropriate for global application. The geospatial liquefaction models are developed using logistic regression from a liquefaction database consisting of the data from 27 earthquake events from six countries. The model that performs best over the entire dataset includes peak ground velocity (PGV), VS30, distance to river, distance to coast, and precipitation. The model that performs best over the noncoastal dataset includes PGV, VS30, water table depth, distance to water body, and precipitation. Second, post-earthquake liquefaction cataloging historically relies on field investigation that is often limited by time and expense, and therefore results in limited and incomplete liquefaction inventories. This dissertation improves the post-earthquake cataloging by the development and validation of a remote sensing-based method that can be quickly applied over a broad region after an earthquake and provide a detailed map of liquefaction surface effects (Chapter 4). Our method uses the optical satellite images before and after an earthquake event from the WorldView-2 satellite with 2 m spatial resolution and eight spectral bands. Our method uses the changes of spectral variables that are sensitive to surface moisture and soil characteristics paired with a supervised classification.

Crucial role of estrogen for the mammalian female in regulating semen coagulation and liquefaction in vivo

PubMed Central

2017-01-01

Semen liquefaction changes semen from a gel-like to watery consistency and is required for sperm to gain mobility and swim to the fertilization site in the Fallopian tubes. Kallikrein-related peptidases 3 (KLK3) and other kallikrein-related peptidases from male prostate glands are responsible for semen liquefaction by cleaving gel-forming proteins (semenogelin and collagen). In a physiological context, the liquefaction process occurs within the female reproductive tract. How seminal proteins interact with the female reproductive environment is still largely unexplored. We previously reported that conditional genetic ablation of Esr1 (estrogen receptor α) in the epithelial cells of the female reproductive tract (Wnt7aCre/+;Esr1f/f) causes female infertility, partly due to a drastic reduction in the number of motile sperm entering the oviduct. In this study, we found that post-ejaculated semen from fertile wild-type males was solidified and the sperm were entrapped in Wnt7aCre/+;Esr1f/f uteri, compared to the watery semen (liquefied) found in Esr1f/f controls. In addition, semenogelin and collagen were not degraded in Wnt7aCre/+;Esr1f/f uteri. Amongst multiple gene families aberrantly expressed in the absence of epithelial ESR1, we have identified that a lack of Klks in the uterus is a potential cause for the liquefaction defect. Pharmacological inhibition of KLKs in the uterus replicated the phenotype observed in Wnt7aCre/+;Esr1f/f uteri, suggesting that loss of uterine and seminal KLK function causes this liquefaction defect. In human cervical cell culture, expression of several KLKs and their inhibitors (SPINKs) was regulated by estrogen in an ESR1-dependent manner. Our study demonstrates that estrogen/ESR1 signaling in the female reproductive tract plays an indispensable role in normal semen liquefaction, providing fundamental evidence that exposure of post-ejaculated semen to the suboptimal microenvironment in the female reproductive tract leads to faulty liquefaction and subsequently causes a fertility defect. PMID:28414719

[Carbon capture and storage (CCS) and its potential role to mitigate carbon emission in China].

PubMed

Chen, Wen-Ying; Wu, Zong-Xin; Wang, Wei-Zhong

2007-06-01

Carbon capture and storage (CCS) has been widely recognized as one of the options to mitigate carbon emission to eventually stabilize carbon dioxide concentration in the atmosphere. Three parts of CCS, which are carbon capture, transport, and storage are assessed in this paper, covering comparisons of techno-economic parameters for different carbon capture technologies, comparisons of storage mechanism, capacity and cost for various storage formations, and etc. In addition, the role of CCS to mitigate global carbon emission is introduced. Finally, China MARKAL model is updated to include various CCS technologies, especially indirect coal liquefaction and poly-generation technologies with CCS, in order to consider carbon emission reduction as well as energy security issue. The model is used to generate different scenarios to study potential role of CCS to mitigate carbon emissions by 2050 in China. It is concluded that application of CCS can decrease marginal abatement cost and the decrease rate can reach 45% for the emission reduction rate of 50%, and it can lessen the dependence on nuclear power development for stringent carbon constrains. Moreover, coal resources can be cleanly used for longer time with CCS, e.g., for the scenario C70, coal share in the primary energy consumption by 2050 will increase from 10% when without CCS to 30% when with CCS. Therefore, China should pay attention to CCS R&D activities and to developing demonstration projects.

Publications of the Fossil Energy Advanced Research and Technology Development Materials Program: April 1, 1993--March 31, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carlson, P.T.

1995-04-01

The objective of the Fossil Energy Advanced Research and Technology Development (AR and TD) Materials Program is to conduct research and development on materials for fossil energy applications, with a focus on the longer-term needs for materials with general applicability to the various fossil fuel technologies. The Program includes research aimed at a better understanding of materials behavior in fossil energy environments and on the development of new materials capable of substantial improvement in plant operations and reliability. The scope of the Program addresses materials requirements for all fossil energy systems, including materials for coal preparation, coal liquefaction, coal gasification,more » heat engines and heat recovery, combustion systems, and fuel cells. Work on the Program is conducted at national and government laboratories, universities, and industrial research facilities. This bibliography covers the period of April 1, 1993, through March 31, 1995, and is a supplement to previous bibliographies in this series. It is the intent of this series of bibliographies to list only those publications that can be conveniently obtained by a researcher through relatively normal channels. The publications listed in this document have been limited to topical reports, open literature publications in refereed journals, full-length papers in published proceedings of conferences, full-length papers in unrefereed journals, and books and book articles. 159 refs.« less

Plan for radionuclide tracer studies of the residence time distribution in the Wilsonville dissolver and preheater

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jolley, R.L.; Begovich, J.M.; Brashear, H.R.

1983-12-01

Stimulus-response measurements using radiotracers to measure residence time distribution (RTD) and hydrodynamic parameters for the preheaters and dissolvers at the Ft. Lewis Solvent Refined Coal (SRC) and the Exxon Donor Solvent (EDS) coal conversion pilot plants are reviewed. A plan is also presented for a series of radioactive tracer studies proposed for the Advanced Coal Liquefaction Facility at Wilsonville, Alabama, to measure the RTD for the preheater and dissolvers in the SRC-I mode. The tracer for the gas phase will be /sup 133/Xe, and /sup 198/Au (on carbonized resin or as an aqueous colloidal suspension) will be used as themore » slurry tracer. Four experimental phases are recommended for the RTD tracer studies: (1) preheater; (2) dissolver with 100% takeoff; (3) dissolver with 100% takeoff and solids withdrawal; and (4) dissolver with 50% takeoff. Eighteen gas-tracer and 22 liquid-tracer injections are projected to accomplish the four experimental phases. Two to four tracer injections are projected for preliminary tests to ensure the capability of safe injection of the radiotracers and the collection of statistically significant data. A complete projected cost and time schedule is provided, including procurement of necessary components, preparation of the radiotracers, assembly and testing of tracer injection apparatus and detection systems, onsite work and tracer injections, laboratory experimentation, data analysis, and report writing.« less

Cryogenic hydrogen-induced air liquefaction technologies

NASA Technical Reports Server (NTRS)

Escher, William J. D.

1990-01-01

Extensively utilizing a special advanced airbreathing propulsion archives database, as well as direct contacts with individuals who were active in the field in previous years, a technical assessment of cryogenic hydrogen-induced air liquefaction, as a prospective onboard aerospace vehicle process, was performed and documented. The resulting assessment report is summarized. Technical findings are presented relating the status of air liquefaction technology, both as a singular technical area, and also that of a cluster of collateral technical areas including: compact lightweight cryogenic heat exchangers; heat exchanger atmospheric constituents fouling alleviation; para/ortho hydrogen shift conversion catalysts; hydrogen turbine expanders, cryogenic air compressors and liquid air pumps; hydrogen recycling using slush hydrogen as heat sink; liquid hydrogen/liquid air rocket-type combustion devices; air collection and enrichment systems (ACES); and technically related engine concepts.

Marsilea spp.-A novel source of lignocellulosic biomass: Effect of solubilized lignin on anaerobic biodegradability and cost of energy products.

PubMed

Rajesh Banu, J; Sugitha, S; Kannah, R Yukesh; Kavitha, S; Yeom, Ick Tae

2018-05-01

The present study concerns the liquefying potential of an unusual source of lignocellulosic biomass (Marsilea spp., water clover, an aquatic fern) during combinative pretreatment. The focus was on how the pretreatment affects the biodegradability, methane production, and profitability of thermochemical dispersion disintegration (TCDD) based on liquefaction and soluble lignin. The TCDD process was effective at 12,000 rpm and 11 min under the optimized thermochemical conditions (80 °C and pH 11). The results from biodegradability tests imply that 30% liquefaction was sufficient to achieve enhanced biodegradability of about 0.280 g-COD/g-COD. When biodegradability was >30% inhibition was observed (0.267 and 0.264 g-COD/g-COD at 35-40% liquefaction) due to higher soluble lignin release (4.53-4.95 g/L). Scalable studies revealed that achievement of 30% liquefaction was beneficial in terms of the energy and cost benefit ratios (0.956 and 1.02), when compared to other choices. Copyright © 2018 Elsevier Ltd. All rights reserved.

THE LIQUEFACTION RISK ANALYSIS OF CEMENT-TREATED SANDY GROUND CONSIDERING THE SPATIAL VARIABILITY OF SOIL STRENGTH

NASA Astrophysics Data System (ADS)

Kataoka, Norio; Kasama, Kiyonobu; Zen, Kouki; Chen, Guangqi

This paper presents a probabilistic method for assessi ng the liquefaction risk of cement-treated ground, which is an anti-liquefaction ground improved by cemen t-mixing. In this study, the liquefaction potential of cement-treated ground is analyzed statistically using Monte Carlo Simulation based on the nonlinear earthquake response analysis consid ering the spatial variability of so il properties. The seismic bearing capacity of partially liquefied ground is analyzed in order to estimat e damage costs induced by partial liquefaction. Finally, the annual li quefaction risk is calcu lated by multiplying the liquefaction potential with the damage costs. The results indicated that the proposed new method enables to evaluate the probability of liquefaction, to estimate the damage costs using the hazard curv e, fragility curve induced by liquefaction, and liq uefaction risk curve.

Liquefaction hazard for the region of Evansville, Indiana

USGS Publications Warehouse

Haase, Jennifer S.; Choi, Yoon S.; Nowack, Robert L.; Cramer, Chris H.; Boyd, Oliver S.; Bauer, Robert A.

2011-01-01

Maps of liquefaction hazard for each scenario earthquake present (1) Mean liquefaction potential index at each site, and (2) Probabilities that liquefaction potential index values exceed 5 (threshold for expression of surface liquefaction) and 12 (threshold for lateral spreading). Values for the liquefaction potential index are high in the River alluvium group, where the soil profiles are predominantly sand, while values in the Lacustrine terrace group are lower, owing to the predominance of clay. Liquefaction potential index values in the Outwash terrace group are less consistent because the soil profiles contain highly variable sequences of silty sand, clayey sand, and sandy clay, justifying the use of the Monte Carlo procedure to capture the consequences of this complexity.

Predicting the spatial extent of liquefaction from geospatial and earthquake specific parameters

USGS Publications Warehouse

Zhu, Jing; Baise, Laurie G.; Thompson, Eric M.; Wald, David J.; Knudsen, Keith L.; Deodatis, George; Ellingwood, Bruce R.; Frangopol, Dan M.

2014-01-01

The spatially extensive damage from the 2010-2011 Christchurch, New Zealand earthquake events are a reminder of the need for liquefaction hazard maps for anticipating damage from future earthquakes. Liquefaction hazard mapping as traditionally relied on detailed geologic mapping and expensive site studies. These traditional techniques are difficult to apply globally for rapid response or loss estimation. We have developed a logistic regression model to predict the probability of liquefaction occurrence in coastal sedimentary areas as a function of simple and globally available geospatial features (e.g., derived from digital elevation models) and standard earthquake-specific intensity data (e.g., peak ground acceleration). Some of the geospatial explanatory variables that we consider are taken from the hydrology community, which has a long tradition of using remotely sensed data as proxies for subsurface parameters. As a result of using high resolution, remotely-sensed, and spatially continuous data as a proxy for important subsurface parameters such as soil density and soil saturation, and by using a probabilistic modeling framework, our liquefaction model inherently includes the natural spatial variability of liquefaction occurrence and provides an estimate of spatial extent of liquefaction for a given earthquake. To provide a quantitative check on how the predicted probabilities relate to spatial extent of liquefaction, we report the frequency of observed liquefaction features within a range of predicted probabilities. The percentage of liquefaction is the areal extent of observed liquefaction within a given probability contour. The regional model and the results show that there is a strong relationship between the predicted probability and the observed percentage of liquefaction. Visual inspection of the probability contours for each event also indicates that the pattern of liquefaction is well represented by the model.

Enzymatic liquefaction of agarose above the sol-gel transition temperature using a thermostable endo-type β-agarase, Aga16B.

PubMed

Kim, Jung Hyun; Yun, Eun Ju; Seo, Nari; Yu, Sora; Kim, Dong Hyun; Cho, Kyung Mun; An, Hyun Joo; Kim, Jae-Han; Choi, In-Geol; Kim, Kyoung Heon

2017-02-01

The main carbohydrate of red macroalgae is agarose, a heterogeneous polysaccharide composed of D-galactose and 3,6-anhydro-L-galactose. When saccharifying agarose by enzymes, the unique physical properties of agarose, namely the sol-gel transition and the near-insolubility of agarose in water, limit the accessibility of agarose to the enzymes. Due to the lower accessibility of agarose to enzymes in the gel state than to the sol state, it is important to prevent the sol-gel transition by performing the enzymatic liquefaction of agarose at a temperature higher than the sol-gel transition temperature of agarose. In this study, a thermostable endo-type β-agarase, Aga16B, originating from Saccharophagus degradans 2-40 T , was characterized and introduced in the liquefaction process. Aga16B was thermostable up to 50 °C and depolymerized agarose mainly into neoagarooligosaccharides with degrees of polymerization 4 and 6. Aga16B was applied to enzymatic liquefaction of agarose at 45 °C, which was above the sol-gel transition temperature of 1 % (w/v) agarose (∼35 °C) when cooling agarose. This is the first systematic demonstration of enzymatic liquefaction of agarose, enabled by determining the sol-gel temperature of agarose under specific conditions and by characterizing the thermostability of an endo-type β-agarase.

The Pathogenesis of Subacute Subdural Hematoma: A Report of 3 Cases and Literature Review.

PubMed

Tao, Zhi-Qiang; Ding, Sheng-Hong; Huang, Jian-Yue; Zhu, Zhi-Gang

2018-06-01

To discuss the pathologic mechanism of subacute subdural hematoma (sASDH). Three typical cases of sASDH were reported, and related literature in Chinese published in the past 15 years was reviewed. Intervals from onset of acute subdural hematoma to surgery or symptom deterioration resulting in sASDH were 12.5-15.5 days (mean 14.1 days). Delayed liquefaction of hematoma clots occurred in all 3 reported cases. One patient achieved good curative effect after administration of dexamethasone, and another patient relapsed owing to poor drainage after evacuation of hematoma. The conversion of acute subdural hematoma to sASDH is an inflammatory reaction process with very regular in time, and it is speculated that the pathologic mechanism may be a delayed hypersensitivity reaction. Antigen released during the liquefaction process of blood clot, with subdural neomembrane cells as antigen-presenting cells, is presented to the T lymphocytes released from the capillaries in the neomembrane and forms sensitized T lymphocytes. When the subsequent antigen is released from the blood clots with a delayed liquefaction and is exposed to sensitized T lymphocytes, the delayed hypersensitivity process occurs. Copyright © 2018 Elsevier Inc. All rights reserved.

A genetic-algorithm approach for assessing the liquefaction potential of sandy soils

NASA Astrophysics Data System (ADS)

Sen, G.; Akyol, E.

2010-04-01

The determination of liquefaction potential is required to take into account a large number of parameters, which creates a complex nonlinear structure of the liquefaction phenomenon. The conventional methods rely on simple statistical and empirical relations or charts. However, they cannot characterise these complexities. Genetic algorithms are suited to solve these types of problems. A genetic algorithm-based model has been developed to determine the liquefaction potential by confirming Cone Penetration Test datasets derived from case studies of sandy soils. Software has been developed that uses genetic algorithms for the parameter selection and assessment of liquefaction potential. Then several estimation functions for the assessment of a Liquefaction Index have been generated from the dataset. The generated Liquefaction Index estimation functions were evaluated by assessing the training and test data. The suggested formulation estimates the liquefaction occurrence with significant accuracy. Besides, the parametric study on the liquefaction index curves shows a good relation with the physical behaviour. The total number of misestimated cases was only 7.8% for the proposed method, which is quite low when compared to another commonly used method.

Large Scale Helium Liquefaction and Considerations for Site Services for a Plant Located in Algeria

NASA Astrophysics Data System (ADS)

Froehlich, P.; Clausen, J. J.

2008-03-01

The large-scale liquefaction of helium extracted from natural gas is depicted. Based on a block diagram the process chain, starting with the pipeline downstream of the natural-gas plant to the final storage of liquid helium, is explained. Information will be provided about the recent experiences during installation and start-up of a bulk helium liquefaction plant located in Skikda, Algeria, including part-load operation based on a reduced feed gas supply. The local working and ambient conditions are described, including challenging logistic problems like shipping and receiving of parts, qualified and semi-qualified subcontractors, basic provisions and tools on site, and precautions to sea water and ambient conditions. Finally, the differences in commissioning (technically and evaluation of time and work packages) to European locations and standards will be discussed.

Cryogenic hydrogen-induced air-liquefaction technologies

NASA Technical Reports Server (NTRS)

Escher, William J. D.

1990-01-01

Extensive use of a special advanced airbreathing propulsion archives data base, as well as direct contacts with individuals who were active in the field in previous years, a technical assessment of cryogenic hydrogen induced air liquefaction, as a prospective onboard aerospace vehicle process, was performed and documented in 1986. The resulting assessment report is summarized. Technical findings relating the status of air liquefaction technology are presented both as a singular technical area, and also as that of a cluster of collateral technical areas including: Compact lightweight cryogenic heat exchangers; Heat exchanger atmospheric constituents fouling alleviation; Para/ortho hydrogen shift conversion catalysts; Hydrogen turbine expanders, cryogenic air compressors and liquid air pumps; Hydrogen recycling using slush hydrogen as heat sinks; Liquid hydrogen/liquid air rocket type combustion devices; Air Collection and Enrichment System (ACES); and Technically related engine concepts.

Liquefaction potential index: Field assessment

USGS Publications Warehouse

Toprak, S.; Holzer, T.L.

2003-01-01

Cone penetration test (CPT) soundings at historic liquefaction sites in California were used to evaluate the predictive capability of the liquefaction potential index (LPI), which was defined by Iwasaki et al. in 1978. LPI combines depth, thickness, and factor of safety of liquefiable material inferred from a CPT sounding into a single parameter. LPI data from the Monterey Bay region indicate that the probability of surface manifestations of liquefaction is 58 and 93%, respectively, when LPI equals or exceeds 5 and 15. LPI values also generally correlate with surface effects of liquefaction: Decreasing from a median of 12 for soundings in lateral spreads to 0 for soundings where no surface effects were reported. The index is particularly promising for probabilistic liquefaction hazard mapping where it may be a useful parameter for characterizing the liquefaction potential of geologic units.

Hydrothermal liquefaction of agricultural and forestry wastes: state-of-the-art review and future prospects.

PubMed

Cao, Leichang; Zhang, Cheng; Chen, Huihui; Tsang, Daniel C W; Luo, Gang; Zhang, Shicheng; Chen, Jianmin

2017-12-01

Hydrothermal liquefaction has been widely applied to obtain bioenergy and high-value chemicals from biomass in the presence of a solvent at moderate to high temperature (200-550°C) and pressure (5-25MPa). This article summarizes and discusses the conversion of agricultural and forestry wastes by hydrothermal liquefaction. The history and development of hydrothermal liquefaction technology for lignocellulosic biomass are briefly introduced. The research status in hydrothermal liquefaction of agricultural and forestry wastes is critically reviewed, particularly for the effects of liquefaction conditions on bio-oil yield and the decomposition mechanisms of main components in biomass. The limitations of hydrothermal liquefaction of agricultural and forestry wastes are discussed, and future research priorities are proposed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Comparative study on liquefaction of creosote and chromated copper arsenate (CCA)-treated wood and untreated southern pine wood: effects of acid catalyst content, liquefaction time, temperature, and phenol to wood ratio

Treesearch

Hui Pan; Chung-Yun Hse; Todd F. Shupe

2009-01-01

Creosote- and chromated copper arsenate (CCA)-treated wood waste and untreated southern pine wood were liquefied with phenol and sulfuric acid. The effects of sulfuric acid content, liquefaction time, liquefaction temperature, and phenol to wood ratio on liquefaction rate (i.e., wood residue content) were investigated and analyzed by analysis of variance (...

Quantitative Characterization of Aqueous Byproducts from Hydrothermal Liquefaction of Municipal Wastes, Food Industry Wastes, and Biomass Grown on Waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maddi, Balakrishna; Panisko, Ellen; Wietsma, Thomas

Hydrothermal liquefaction (HTL) is a viable thermochemical process for converting wet solid wastes into biocrude which can be hydroprocessed to liquid transportation fuel blendstocks and specialty chemicals. The aqueous byproduct from HTL contains significant amounts (20 to 50%) of the feed carbon, which must be used to enhance economic sustainability of the process on an industrial scale. In this study, aqueous fractions produced from HTL of industrial and municipal waste were characterized using a wide variety of analytical approaches. Organic chemical compounds present in these aqueous fractions were identified using two-dimensional gas chromatography equipped with time-of-flight mass spectrometry. Identified compoundsmore » include organic acids, nitrogen compounds, alcohols, aldehydes, and ketones. Conventional gas chromatography and liquid chromatography methods were employed to quantify the identified compounds. Inorganic species, in the aqueous stream of hydrothermal liquefaction of these aqueous byproducts, also were quantified using ion chromatography and inductively coupled plasma optical emission spectroscopy. The concentrations of organic chemical compounds and inorganic species are reported, and the significance of these results is discussed in detail.« less

Assessment of liquefaction potential index for Mumbai city

NASA Astrophysics Data System (ADS)

Dixit, J.; Dewaikar, D. M.; Jangid, R. S.

2012-09-01

Mumbai city is the financial capital of India and is fifth most densely populated city in the world. Seismic soil liquefaction is evaluated for Mumbai city in terms of the factors of safety against liquefaction (FS) along the depths of soil profiles for different earthquakes with 2% probability of exceedance in 50 yr using standard penetration test (SPT)-based simplified empirical procedure. This liquefaction potential is evaluated at 142 representative sites in the city using the borehole records from standard penetration tests. Liquefaction potential index (LPI) is evaluated at each borehole location from the obtained factors of safety (FS) to predict the potential of liquefaction to cause damage at the surface level at the site of interest. Spatial distribution of soil liquefaction potential is presented in the form of contour maps of LPI values. As the majority of the sites in the city are of reclaimed land, the vulnerability of liquefaction is observed to be very high at many places.

Apparatus for the liquefaction of natural gas and methods relating to same

DOEpatents

Wilding, Bruce M [Idaho Falls, ID; McKellar, Michael G [Idaho Falls, ID; Turner, Terry D [Ammon, ID; Carney, Francis H [Idaho Falls, ID

2009-09-29

An apparatus and method for producing liquefied natural gas. A liquefaction plant may be coupled to a source of unpurified natural gas, such as a natural gas pipeline at a pressure letdown station. A portion of the gas is drawn off and split into a process stream and a cooling stream. The cooling stream passes through an expander creating work output. A compressor may be driven by the work output and compresses the process stream. The compressed process stream is cooled, such as by the expanded cooling stream. The cooled, compressed process stream is divided into first and second portions with the first portion being expanded to liquefy the natural gas. A gas-liquid separator separates the vapor from the liquid natural gas. The second portion of the cooled, compressed process stream is also expanded and used to cool the compressed process stream.

Documenting Liquefaction Failures Using Satellite Remote Sensing and Artificial Intelligence Algorithms

NASA Astrophysics Data System (ADS)

Oommen, T.; Baise, L. G.; Gens, R.; Prakash, A.; Gupta, R. P.

2009-12-01

Historically, earthquake induced liquefaction is known to have caused extensive damage around the world. Therefore, there is a compelling need to characterize and map liquefaction after a seismic event. Currently, after an earthquake event, field-based mapping of liquefaction is sporadic and limited due to inaccessibility, short life of the failures, difficulties in mapping large aerial extents, and lack of resources. We hypothesize that as liquefaction occurs in saturated granular soils due to an increase in pore pressure, the liquefaction related terrain changes should have an associated increase in soil moisture with respect to the surrounding non-liquefied regions. The increase in soil moisture affects the thermal emittance and, hence, change detection using pre- and post-event thermal infrared (TIR) imagery is suitable for identifying areas that have undergone post-earthquake liquefaction. Though change detection using TIR images gives the first indication of areas of liquefaction, the spatial resolution of TIR images is typically coarser than the resolution of corresponding visible, near-infrared (NIR), and shortwave infrared (SWIR) images. We hypothesize that liquefaction induced changes in the soil and associated surface effects cause textural and spectral changes in images acquired in the visible, NIR, and SWIR. Although these changes can be from various factors, a synergistic approach taking advantage of the thermal signature variation due to changing soil moisture condition, together with the spectral information from high resolution visible, NIR, and SWIR bands can help to narrow down the locations of post-event liquefaction for regional documentation. In this study, we analyze the applicability of combining various spectral bands from different satellites (Landsat, Terra-MISR, IRS-1C, and IRS-1D) for documenting liquefaction failures associated with the magnitude 7.6 earthquake that occurred in Bhuj, India, in 2001. We combine the various spectral bands by neighborhood correlation image analysis using an artificial intelligence algorithm called support vector machine to remotely identify and document liquefaction failures across a region; and assess the reliability and accuracy of the thermal remote sensing approach in documenting regional liquefaction failures. Finally, we present the applicability of the satellite data analyzed and appropriateness of a multisensor and multispectral approach for documenting liquefaction related failures.

Liquefaction at Oceano, California, during the 2003 San Simeon earthquake

USGS Publications Warehouse

Holzer, T.L.; Noce, T.E.; Bennett, M.J.; Tinsley, J. C.; Rosenberg, L.I.

2005-01-01

The 2003 M 6.5 San Simeon, California, earthquake caused liquefaction-induced lateral spreading at Oceano at an unexpectedly large distance from the seismogenic rupture. We conclude that the liquefaction was caused by ground motion that was enhanced by both rupture directivity in the mainshock and local site amplification by unconsolidated fine-grained deposits. Liquefaction occurred in sandy artificial fill and undisturbed eolian sand and fluvial deposits. The largest and most damaging lateral spread was caused by liquefaction of artificial fill; the head of this lateral spread coincided with the boundary between the artificial fill and undisturbed eolian sand deposits. Values of the liquefaction potential index, in general, were greater than 5 at liquefaction sites, the threshold value that has been proposed for liquefaction hazard mapping. Although the mainshock ground motion at Oceano was not recorded, peak ground acceleration was estimated to range from 0.25 and 0.28g on the basis of the liquefaction potential index and aftershock recordings. The estimates fall within the range of peak ground acceleration values associated with the modified Mercalli intensity = VII reported at the U.S. Geological Survey (USGS) "Did You Feel It?" web site.

Probabilistic evaluation of damage potential in earthquake-induced liquefaction in a 3-D soil deposit

NASA Astrophysics Data System (ADS)

Halder, A.; Miller, F. J.

1982-03-01

A probabilistic model to evaluate the risk of liquefaction at a site and to limit or eliminate damage during earthquake induced liquefaction is proposed. The model is extended to consider three dimensional nonhomogeneous soil properties. The parameters relevant to the liquefaction phenomenon are identified, including: (1) soil parameters; (2) parameters required to consider laboratory test and sampling effects; and (3) loading parameters. The fundamentals of risk based design concepts pertient to liquefaction are reviewed. A detailed statistical evaluation of the soil parameters in the proposed liquefaction model is provided and the uncertainty associated with the estimation of in situ relative density is evaluated for both direct and indirect methods. It is found that the liquefaction potential the uncertainties in the load parameters could be higher than those in the resistance parameters.

A classification of morphoseismic features in the New Madrid seismic zone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knox, R.; Stewart, D.

1993-03-01

The New Madrid Seismic Zone (NMSZ) contains thousands of surface features distributed over 5,000 square miles in four states. These are attributable to some combination of (1) seismically-induced liquefaction (SIL), (2) secondary deformation, and (3) seismically-induced slope failures. Most of these features were produced by the 1811--12 series of great earthquakes, but some predate and some postdate 1811--12. Subsequent non-seismic factors, such as hydrologically-induced liquefaction (HIL), mechanically-induced liquefaction (MIL), human activities, mass wasting, eolian and fluvial processes have modified all of these features. Morphoseismic features are new landforms produced by earthquakes, or are pre-existing landforms modified by them. Involved aremore » complex interrelationships among several variables, including: (1) intensity and duration of seismic ground motion, (2) surface wave harmonics, (3) depth to water table, (4) depth to basement, (5) particle size, composition, and sorting of sediment making up the liquefied (LZ) and non-liquefied zones (NLZ), (6) topographic parameters, and (7) attitudes of beds and lenses susceptible to liquefaction. Morphoseismic features are depicted as results of a time-flow sequence initiated by primary basement disturbances which produce three major categories of surface response: secondary deformation, liquefaction and slope failure. Nine subcategories incorporate features produced by or resulting in: extruded sand, intruded sand, lateral spreading, faulting, subsidence of large areas, uplift of large areas, altered streams, coherent landslides, and incoherent landslides. The total morphoseismic features identified by this classification are 34 in number.« less

Results of hydrotreating the kerosene fraction of HTI`S first proof of concept run

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stohl, F.V.; Lott, S.E.; Diegert, K.V.

1996-06-01

The objective of Sandia`s hydrotreating study is to determine the relationships between hydrotreating conditions and product characteristics for coal liquids produced using current technologies. The coal-derived liquid used in the current work is the kerosene fraction of the product from Hydrocarbon Technologies Inc.`s first proof-of-concept run for it`s Catalytic Two-Stage Liquefaction Technology. Sandia`s hydrotreating experiments were performed in a continuous operation, microflow reactor system using aged HDN-60 catalyst. A factorial experimental design with three variables (temperature, pressure, liquid hourly space velocity) was used in this work. Nitrogen and sulfur contents of the feed and hydrotreated products were determined using anmore » Antek 7000 Sulfur and Nitrogen Analyzer. Multiple samples were collected at each set of reaction conditions to ensure that each condition was lined out. Hydrotreating at each set of reaction conditions was repeated so that results could be normalized for catalyst deactivation. The normalized results were statistically analyzed. Increases in temperature and pressure had the greatest effects on nitrogen removal. The highest severity condition (388{degrees}C, 1500 psig H{sub 2}, 1.5g/h/g(cat)) gave a measured nitrogen value of <5 ppm.« less

Results of hydrotreating the kerosene fraction of HTI`S first proof of concept run

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stohl, F.V.; Lott, S.E.; Diegert, K.V.

1996-12-31

The objective of Sandia`s hydrotreating study is to determine the relationships between hydrotreating conditions and product characteristics for coal liquids produced using current technologies. The coal-derived liquid used in the current work is the kerosene fraction of the product from Hydrocarbon Technologies Inc.`s first proof-of-concept run for it`s Catalytic Two-Stage Liquefaction Technology. Sandia`s hydrotreating experiments were performed in a continuous operation, microflow reactor system using aged HDN-60 catalyst. A factorial experimental design with three variables (temperature, pressure, liquid hourly space velocity) was used in this work. Nitrogen and sulfur contents of the feed and hydrotreated products were determined using anmore » Antek 7000 Sulfur and Nitrogen Analyzer. Multiple samples were collected at each set of reaction conditions to ensure that each condition was lined out. Hydrotreating at each set of reaction conditions was repeated so that results could be normalized for catalyst deactivation. The normalized results were statistically analyzed. Increases in temperature and pressure had the greatest effects on nitrogen removal. The highest severity condition (388{degrees}C, 1500 psig H{sub 2}, 1.5g/h/g(cat)) gave a measured nitrogen value of <5 ppm.« less

Chemical analysis and biological testing of materials from the EDS coal liquefaction process: a status report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Later, D.W.; Pelroy, R.A.; Wilson, B.W.

1984-05-01

Representative process materials were obtained from the EDS pilot plant for chemical and biological analyses. These materials were characterized for biological activity and chemical composition using a microbial mutagenicity assay and chromatographic and mass spectrometric analytical techniques. The two highest boiling distillation cuts, as well as process solvent (PS) obtained from the bottoms recycle mode operation, were tested for initiation of mouse skin tumorigenicity. All three materials were active; the crude 800/sup 0 +/F cut was substantially more potent than the crude bottoms recycle PS or 750 to 800/sup 0/F distillate cut. Results from chemical analyses showed the EDS materials,more » in general, to be more highly alkylated and have higher hydroaromatic content than analogous SRC II process materials (no in-line process hydrogenation) used for comparison. In the microbial mutagenicity assays the N-PAC fractions showed greater activity than did the aliphatic hydrocarbon, hydroxy-PAH, or PAH fractions, although mutagenicity was detected in certain PAH fractions by a modified version of the standard microbial mutagenicity assay. Mutagenic activities for the EDS materials were lower, overall, than those for the corresponding materials from the SRC II process. The EDS materials produced under different operational modes had distinguishable differences in both their chemical constituency and biological activity. The primary differences between the EDS materials studied here and their SRC II counterparts used for comparison are most likely attributable to the incorporation of catalytic hydrogenation in the EDS process. 27 references, 28 figures, 27 tables.« less

Apparatus for the liquefaction of natural gas and methods relating to same

DOEpatents

Turner, Terry D [Ammon, ID; Wilding, Bruce M [Idaho Falls, ID; McKellar, Michael G [Idaho Falls, ID

2009-09-22

An apparatus and method for producing liquefied natural gas. A liquefaction plant may be coupled to a source of unpurified natural gas, such as a natural gas pipeline at a pressure letdown station. A portion of the gas is drawn off and split into a process stream and a cooling stream. The cooling stream passes through an expander creating work output. A compressor may be driven by the work output and compresses the process stream. The compressed process stream is cooled, such as by the expanded cooling stream. The cooled, compressed process stream is expanded to liquefy the natural gas. A gas-liquid separator separates a vapor from the liquid natural gas. A portion of the liquid gas is used for additional cooling. Gas produced within the system may be recompressed for reintroduction into a receiving line or recirculation within the system for further processing.

Advanced studies of biological indirect liquefaction of coal: Topical report on Task 1: Culture identification

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Culture identification and characterization studies carried out at the University of Arkansas and under contract to the University of Oklahoma, Department of Botany and Microbiology, have been essentially completed. The studies indicate that the organism is indeed a new clostridial strain, to be named Clostridium ljungdahlii, strain PETC, in honor of Dr. Lars G. Ljungdahl for his work on clostridia and acetogens. C. ljungdahlii is different from other clostridial strains and similar geni in its operating conditions and choice of substrates as sole carbon and energy sources. C. ljungdahlii, strain PETC, produces ethanol as a product only at low pHmore » levels, with acetate the primary product at higher pH levels. 46 refs., 5 figs., 6 tabs.« less

Efficiency of jet grout columns and sand-recycled material mixtures for mitigating liquefaction damage

NASA Astrophysics Data System (ADS)

Kerem Ertek, M.; Demir, Gökhan; Köktan, Utku

2017-04-01

Liquefaction is an important seismic phenomena that has to be assessed and consequently makes it essential to take measures in order to reduce related hazards. There are several ways to assess liquefaction potential analytically and some constitutive models implemented in FEM softwares presenting cyclic behaviour of sand making it possible to observe shear strain or excess pore pressure ratio which are measures to hold a view about liquefaction occurrence. According to various studies in the literature, post-earthquake inspections show that the measures in terms of grouting, piled rafts and sand mixtures with different non-liquefiable materials reduce liquefaction related damage. This paper aims to provide a brief information about effectiveness of jet-grout columns and recycled material-sand mixtures against liquefaction by the help of numerical analyses performed with MIDAS GTS NX software with regard to generation of shear strains. Key words: liquefaction, numerical analyses, jet-grout, sand mixtures

Optimization for microwave-assisted direct liquefaction of bamboo residue in glycerol/methanol mixtures

Treesearch

Jiulong Xie; Jinqiu Qi; Chungyun Hse; Todd F. Shupe

2015-01-01

Bamboo residues were liquefied in a mixture of glycerol and methanol in the presence of sulfuric acid using microwave energy. We investigated the effects of liquefaction conditions, including glycerol/methanol ratio, liquefaction temperature, and reaction time on the conversion yield. The optimal liquefaction conditions were under the temperature of 120

Characterization of liquefied wood residues from different liquefaction conditions

Treesearch

Hui Pan; Todd f. Shupe; Chung-Yun Hse

2007-01-01

The amount of wood residue is used as a measurement of the extent of wood liquefaction. Characterization of the residue from wood liquefaction provides a new approach to understand some fundamental aspects of the liquefaction reaction. Residues were characterized by wet chemical analyses, Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), and...

Study Gradation and Moisture Content of Sand Embankment on Peat Subjected Vibration Potential Liquefaction

NASA Astrophysics Data System (ADS)

Agus Nugroho, Soewignjo; Ika Putra, Agus; Yusa, Muhamad

2018-03-01

In recent years large earthquakes often occur on the island of Sumatra. There is a phenomenon of the damage occurred during the earthquake, one of the effects is a phenomenon of loss of soil strength due to vibration called liquefaction. Some cases of liquefaction occur in some areas in Aceh, Nias Island, Padang and Pariaman. Pekanbaru is located close to the fault area that causes the occurrence of earthquake wave propagation. Pekanbaru are also at risk for geotechnical problems because of earthquake such as liquefaction. Evaluation of liquefaction potential could using by in-situ test and by laboratory test. The laboratory test to evaluation liquefaction potential among which method of experiment shaking table. In this study, liquefaction phenomenon was conducted by creating a physical model of a laboratory scale using a one-way vibration machine, with a review of how big the influence of sand gradation, sand shaped and grain-size, and surface water level in the sand against liquefaction potential. Evaluate of liquefaction potential based on the surface reading of the soil movement, elapsed time for final settlement and an excess pore water dissipation (EPD) during testing. Based on the results of performed test, indicated that fine sand on fully saturated conditions have the potential of maximum settlement for 20.67% and maximum ascend of pore water for 46.67%. This result mean that poorly graded fine sand on fully saturated conditions has more liquefaction potential than medium sand, coarse sand, and well graded sand

LNG projects make progress in Oman and Yemen

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1997-02-24

Two LNG projects in the Middle East, one in Oman and the other in Yemen, are due on stream at the turn of the century--each the largest single project ever put together in its country. Officials described their projects at a yearend 1996 conference in Paris by Institut Francais du Petrole and Petrostrategies. The Oman project develops gas reserves, does gas processing, and transports the gas 360 km to a liquefaction plant to be built on the coast. The Yemen project involves a liquefaction plant and an export terminal.

Evaluating simplified methods for liquefaction assessment for loss estimation

NASA Astrophysics Data System (ADS)

Kongar, Indranil; Rossetto, Tiziana; Giovinazzi, Sonia

2017-06-01

Currently, some catastrophe models used by the insurance industry account for liquefaction by applying a simple factor to shaking-induced losses. The factor is based only on local liquefaction susceptibility and this highlights the need for a more sophisticated approach to incorporating the effects of liquefaction in loss models. This study compares 11 unique models, each based on one of three principal simplified liquefaction assessment methods: liquefaction potential index (LPI) calculated from shear-wave velocity, the HAZUS software method and a method created specifically to make use of USGS remote sensing data. Data from the September 2010 Darfield and February 2011 Christchurch earthquakes in New Zealand are used to compare observed liquefaction occurrences to forecasts from these models using binary classification performance measures. The analysis shows that the best-performing model is the LPI calculated using known shear-wave velocity profiles, which correctly forecasts 78 % of sites where liquefaction occurred and 80 % of sites where liquefaction did not occur, when the threshold is set at 7. However, these data may not always be available to insurers. The next best model is also based on LPI but uses shear-wave velocity profiles simulated from the combination of USGS VS30 data and empirical functions that relate VS30 to average shear-wave velocities at shallower depths. This model correctly forecasts 58 % of sites where liquefaction occurred and 84 % of sites where liquefaction did not occur, when the threshold is set at 4. These scores increase to 78 and 86 %, respectively, when forecasts are based on liquefaction probabilities that are empirically related to the same values of LPI. This model is potentially more useful for insurance since the input data are publicly available. HAZUS models, which are commonly used in studies where no local model is available, perform poorly and incorrectly forecast 87 % of sites where liquefaction occurred, even at optimal thresholds. This paper also considers two models (HAZUS and EPOLLS) for estimation of the scale of liquefaction in terms of permanent ground deformation but finds that both models perform poorly, with correlations between observations and forecasts lower than 0.4 in all cases. Therefore these models potentially provide negligible additional value to loss estimation analysis outside of the regions for which they have been developed.

Liquefaction behaviors of bamboo residues in a glycerol-based solvent using microwave energy

Treesearch

Jiulong Xie; Chung-Yun Hse; Todd F. Shupe; Jinqiu Qi; Hui Pan

2014-01-01

Liquefaction of bamboo was performed in glycerol–methanol as co-solvent using microwave energy and was evaluated by characterizing the liquefied residues. High efficiency conversion of bamboo was achieved under mild reaction conditions. Liquefaction temperature and time interacted to affect the liquefaction reaction. Fourier transform infrared analyzes of the residues...

Investigation of Gas Holdup in a Vibrating Bubble Column

NASA Astrophysics Data System (ADS)

Mohagheghian, Shahrouz; Elbing, Brian

2015-11-01

Synthetic fuels are part of the solution to the world's energy crisis and climate change. Liquefaction of coal during the Fischer-Tropsch process in a bubble column reactor (BCR) is a key step in production of synthetic fuel. It is known from the 1960's that vibration improves mass transfer in bubble column. The current study experimentally investigates the effect that vibration frequency and amplitude has on gas holdup and bubble size distribution within a bubble column. Air (disperse phase) was injected into water (continuous phase) through a needle shape injector near the bottom of the column, which was open to atmospheric pressure. The air volumetric flow rate was measured with a variable area flow meter. Vibrations were generated with a custom-made shaker table, which oscillated the entire column with independently specified amplitude and frequency (0-30 Hz). Geometric dependencies can be investigated with four cast acrylic columns with aspect ratios ranging from 4.36 to 24, and injector needle internal diameters between 0.32 and 1.59 mm. The gas holdup within the column was measured with a flow visualization system, and a PIV system was used to measure phase velocities. Preliminary results for the non-vibrating and vibrating cases will be presented.

Apparatus For The Liquefaaction Of Natural Gas And Methods Relating To Same

DOEpatents

Wilding, Bruce M.; Bingham, Dennis N.; McKellar, Michael G.; Turner, Terry D.; Rateman, Kevin T.; Palmer, Gary L.; Klinger, Kerry M.; Vranicar, John J.

2005-11-08

An apparatus and method for producing liquefied natural gas. A liquefaction plant may be coupled to a source of unpurified natural gas, such as a natural gas pipeline at a pressure letdown station. A portion of the gas is drawn off and split into a process stream and a cooling stream. The cooling stream passes through a turbo expander creating work output. A compressor is driven by the work output and compresses the process stream. The compressed process stream is cooled, such as by the expanded cooling stream. The cooled, compressed process stream is divided into first and second portions with the first portion being expanded to liquefy the natural gas. A gas-liquid separator separates the vapor from the liquid natural gas. The second portion of the cooled, compressed process stream is also expanded and used to cool the compressed process stream. Additional features and techniques may be integrated with the liquefaction process including a water clean-up cycle and a carbon dioxide (CO2) clean-up cycle.

Apparatus For The Liquefaaction Of Natural Gas And Methods Relating To Same

DOEpatents

Wilding, Bruce M.; Bingham, Dennis N.; McKellar, Michael G.; Turner, Terry D.; Raterman, Kevin T.; Palmer, Gary L.; Klingler, Kerry M.; Vranicar, John J.

2005-05-03

An apparatus and method for producing liquefied natural gas. A liquefaction plant may be coupled to a source of unpurified natural gas, such as a natural gas pipeline at a pressure letdown station. A portion of the gas is drawn off and split into a process stream and a cooling stream. The cooling stream passes through a turbo expander creating work output. A compressor is driven by the work output and compresses the process stream. The compressed process stream is cooled, such as by the expanded cooling stream. The cooled, compressed process stream is divided into first and second portions with the first portion being expanded to liquefy the natural gas. A gas-liquid separator separates the vapor from the liquid natural gas. The second portion of the cooled, compressed process stream is also expanded and used to cool the compressed process stream. Additional features and techniques may be integrated with the liquefaction process including a water clean-up cycle and a carbon dioxide (CO2) clean-up cycle.

Apparatus For The Liquefaaction Of Natural Gas And Methods Relating To Same

DOEpatents

Wilding, Bruce M.; Bingham, Dennis N.; McKellar, Michael G.; Turner, Terry D.; Raterman, Kevin T.; Palmer, Gary L.; Klingler, Kerry M.; Vranicar, John J.

2003-06-24

An apparatus and method for producing liquefied natural gas. A liquefaction plant may be coupled to a source of unpurified natural gas, such as a natural gas pipeline at a pressure letdown station. A portion of the gas is drawn off and split into a process stream and a cooling stream. The cooling stream passes through a turbo expander creating work output. A compressor is driven by the work output and compresses the process stream. The compressed process stream is cooled, such as by the expanded cooling stream. The cooled, compressed process stream is divided into first and second portions with the first portion being expanded to liquefy the natural gas. A gas-liquid separator separates the vapor from the liquid natural gas. The second portion of the cooled, compressed process stream is also expanded and used to cool the compressed process stream. Additional features and techniques may be integrated with the liquefaction process including a water clean-up cycle and a carbon dioxide (CO.sub.2) clean-up cycle.

Evaluation of liquefaction potential of soil based on standard penetration test using multi-gene genetic programming model

NASA Astrophysics Data System (ADS)

Muduli, Pradyut; Das, Sarat

2014-06-01

This paper discusses the evaluation of liquefaction potential of soil based on standard penetration test (SPT) dataset using evolutionary artificial intelligence technique, multi-gene genetic programming (MGGP). The liquefaction classification accuracy (94.19%) of the developed liquefaction index (LI) model is found to be better than that of available artificial neural network (ANN) model (88.37%) and at par with the available support vector machine (SVM) model (94.19%) on the basis of the testing data. Further, an empirical equation is presented using MGGP to approximate the unknown limit state function representing the cyclic resistance ratio (CRR) of soil based on developed LI model. Using an independent database of 227 cases, the overall rates of successful prediction of occurrence of liquefaction and non-liquefaction are found to be 87, 86, and 84% by the developed MGGP based model, available ANN and the statistical models, respectively, on the basis of calculated factor of safety (F s) against the liquefaction occurrence.

Combined Brayton-JT cycles with refrigerants for natural gas liquefaction

NASA Astrophysics Data System (ADS)

Chang, Ho-Myung; Park, Jae Hoon; Lee, Sanggyu; Choe, Kun Hyung

2012-06-01

Thermodynamic cycles for natural gas liquefaction with single-component refrigerants are investigated under a governmental project in Korea, aiming at new processes to meet the requirements on high efficiency, large capacity, and simple equipment. Based upon the optimization theory recently published by the present authors, it is proposed to replace the methane-JT cycle in conventional cascade process with a nitrogen-Brayton cycle. A variety of systems to combine nitrogen-Brayton, ethane-JT and propane-JT cycles are simulated with Aspen HYSYS and quantitatively compared in terms of thermodynamic efficiency, flow rate of refrigerants, and estimated size of heat exchangers. A specific Brayton-JT cycle is suggested with detailed thermodynamic data for further process development. The suggested cycle is expected to be more efficient and simpler than the existing cascade process, while still taking advantage of easy and robust operation with single-component refrigerants.

Apparatus for the liquefaction of a gas and methods relating to same

DOEpatents

Turner, Terry D [Idaho Falls, ID; Wilding, Bruce M [Idaho Falls, ID; McKellar, Michael G [Idaho Falls, ID

2009-12-29

Apparatuses and methods are provided for producing liquefied gas, such as liquefied natural gas. In one embodiment, a liquefaction plant may be coupled to a source of unpurified natural gas, such as a natural gas pipeline at a pressure letdown station. A portion of the gas is drawn off and split into a process stream and a cooling stream. The cooling stream may be sequentially pass through a compressor and an expander. The process stream may also pass through a compressor. The compressed process stream is cooled, such as by the expanded cooling stream. The cooled, compressed process stream is expanded to liquefy the natural gas. A gas-liquid separator separates the vapor from the liquid natural gas. A portion of the liquid gas may be used for additional cooling. Gas produced within the system may be recompressed for reintroduction into a receiving line.

Using design of experiments to optimize derivatization with methyl chloroformate for quantitative analysis of the aqueous phase from hydrothermal liquefaction of biomass.

PubMed

Madsen, René Bjerregaard; Jensen, Mads Mørk; Mørup, Anders Juul; Houlberg, Kasper; Christensen, Per Sigaard; Klemmer, Maika; Becker, Jacob; Iversen, Bo Brummerstedt; Glasius, Marianne

2016-03-01

Hydrothermal liquefaction is a promising technique for the production of bio-oil. The process produces an oil phase, a gas phase, a solid residue, and an aqueous phase. Gas chromatography coupled with mass spectrometry is used to analyze the complex aqueous phase. Especially small organic acids and nitrogen-containing compounds are of interest. The efficient derivatization reagent methyl chloroformate was used to make analysis of the complex aqueous phase from hydrothermal liquefaction of dried distillers grains with solubles possible. A circumscribed central composite design was used to optimize the responses of both derivatized and nonderivatized analytes, which included small organic acids, pyrazines, phenol, and cyclic ketones. Response surface methodology was used to visualize significant factors and identify optimized derivatization conditions (volumes of methyl chloroformate, NaOH solution, methanol, and pyridine). Twenty-nine analytes of small organic acids, pyrazines, phenol, and cyclic ketones were quantified. An additional three analytes were pseudoquantified with use of standards with similar mass spectra. Calibration curves with high correlation coefficients were obtained, in most cases R (2)  > 0.991. Method validation was evaluated with repeatability, and spike recoveries of all 29 analytes were obtained. The 32 analytes were quantified in samples from the commissioning of a continuous flow reactor and in samples from recirculation experiments involving the aqueous phase. The results indicated when the steady-state condition of the flow reactor was obtained and the effects of recirculation. The validated method will be especially useful for investigations of the effect of small organic acids on the hydrothermal liquefaction process.

Energy-efficient methane production from macroalgal biomass through chemo disperser liquefaction.

PubMed

Tamilarasan, K; Kavitha, S; Rajesh Banu, J; Arulazhagan, P; Yeom, Ick Tae

2017-03-01

In this study, an effort has been made to reduce the energy cost of liquefaction by coupling a mechanical disperser with a chemical (sodium tripolyphosphate). In terms of the cost and specific energy demand of liquefaction, the algal biomass disintegrated at 12,000rpm for 30min, and an STPP dosage of about 0.04g/gCOD was chosen as an optimal parameter. Chemo disperser liquefaction (CDL) was found to be energetically and economically sustainable in terms of liquefaction, methane production, and net profit (15%, 0.14gCOD/gCOD, and 4 USD/Ton of algal biomass) and preferable to disperser liquefaction (DL) (10%, 0.11 gCOD/gCOD, and -475 USD/Ton of algal biomass). Copyright © 2016 Elsevier Ltd. All rights reserved.

Probabilistic liquefaction hazard analysis at liquefied sites of 1956 Dunaharaszti earthquake, in Hungary

NASA Astrophysics Data System (ADS)

Győri, Erzsébet; Gráczer, Zoltán; Tóth, László; Bán, Zoltán; Horváth, Tibor

2017-04-01

Liquefaction potential evaluations are generally made to assess the hazard from specific scenario earthquakes. These evaluations may estimate the potential in a binary fashion (yes/no), define a factor of safety or predict the probability of liquefaction given a scenario event. Usually the level of ground shaking is obtained from the results of PSHA. Although it is determined probabilistically, a single level of ground shaking is selected and used within the liquefaction potential evaluation. In contrary, the fully probabilistic liquefaction potential assessment methods provide a complete picture of liquefaction hazard, namely taking into account the joint probability distribution of PGA and magnitude of earthquake scenarios; both of which are key inputs in the stress-based simplified methods. Kramer and Mayfield (2007) has developed a fully probabilistic liquefaction potential evaluation method using a performance-based earthquake engineering (PBEE) framework. The results of the procedure are the direct estimate of the return period of liquefaction and the liquefaction hazard curves in function of depth. The method combines the disaggregation matrices computed for different exceedance frequencies during probabilistic seismic hazard analysis with one of the recent models for the conditional probability of liquefaction. We have developed a software for the assessment of performance-based liquefaction triggering on the basis of Kramer and Mayfield method. Originally the SPT based probabilistic method of Cetin et al. (2004) was built-in into the procedure of Kramer and Mayfield to compute the conditional probability however there is no professional consensus about its applicability. Therefore we have included not only Cetin's method but Idriss and Boulanger (2012) SPT based moreover Boulanger and Idriss (2014) CPT based procedures into our computer program. In 1956, a damaging earthquake of magnitude 5.6 occurred in Dunaharaszti, in Hungary. Its epicenter was located about 5 km from the southern boundary of Budapest. The quake caused serious damages in the epicentral area and in the southern districts of the capital. The epicentral area of the earthquake is located along the Danube River. Sand boils were observed in some locations that indicated the occurrence of liquefaction. Because their exact locations were recorded at the time of the earthquake, in situ geotechnical measurements (CPT and SPT) could be performed at two (Dunaharaszti and Taksony) sites. The different types of measurements enabled the probabilistic liquefaction hazard computations at the two studied sites. We have compared the return periods of liquefaction that were computed using different built-in simplified stress based methods.

Pulmonary toxicity of a coal liquefaction distillate product

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haschek, W.M.; Boling, M.E.; Guerin, M.R.

1979-01-01

The pulmonary toxicity of coal derived liquids are under study. Results on a sample from the ZnCl/sub 2/ hydrocracking process are presented as an example. We obtained data on its distribution and persistence in the lung as well as the tissue reaction elicited. We also examined individual chemical fractions to determine which was responsible for pulmonary toxicity. Fifty ..mu..l of the distillate or fraction was administered intratracheally to adult male SPF Fisher rats which were then killed at varying time-points, ranging from 1 to 60 days after administration. Enzyme analysis of pulmonary lavage fluid, /sup 3/H-thymidine incorporation into pulmonary DNA,more » autoradiography, light and fluorescence microscopy were performed. At necropsy the distillate, a black viscid fluid, could be seen within major airways in some lobes. Extensive consolidation and atelectasis or, less frequently, overinflation was present in affected lobes. Twenty-four hours after administration the distillate remained visible in large and small airways as well as in the adjacent parenchyma producing a suppurative necrotizing bronchiolitis and pneumonitis. Within 4 days a histiocytic-fibroblastic reaction to the distillate resulted in granulomatous lesions in the parenchyma, as well as polypoid hyperplasia and obliterating bronchiolitis in the severely damaged airways. Extensive epithelial changes consisting of goblet and columnar cell hyperplasia, as well as squamous metaplasia with focal dysplasia were present throughout the respiratory tract at this time. Similar lesions were produced by the ether-soluble acid fraction, while the mono- and di-aromatic fraction produced less severe lesions which were localized to the airways. After 60 days the product distillate, primarily localized within granulomas, still persisted within the lung as visualized by fluorescence microscopy. Mucoid bronchiolitis with scattered polypoid hyperplasia, as well as epithelial hyperplasia and metaplasia were also present.« less

Liquefaction and other ground failures in Imperial County, California, from the April 4, 2010, El Mayor-Cucapah earthquake

USGS Publications Warehouse

McCrink, Timothy P.; Pridmore, Cynthia L.; Tinsley, John C.; Sickler, Robert R.; Brandenberg, Scott J.; Stewart, Jonathan P.

2011-01-01

The Colorado River Delta region of southern Imperial Valley, California, and Mexicali Valley, Baja California, is a tectonically dynamic area characterized by numerous active faults and frequent large seismic events. Significant earthquakes that have been accompanied by surface fault rupture and/or soil liquefaction occurred in this region in 1892 (M7.1), 1915 (M6.3; M7.1), 1930 (M5.7), 1940 (M6.9), 1950 (M5.4), 1957 (M5.2), 1968 (6.5), 1979 (6.4), 1980 (M6.1), 1981 (M5.8), and 1987 (M6.2; M6.8). Following this trend, the M7.2 El Mayor-Cucapah earthquake of April 4, 2010, ruptured approximately 120 kilometers along several known faults in Baja California. Liquefaction caused by the M7.2 El Mayor-Cucapah earthquake was widespread throughout the southern Imperial Valley but concentrated in the southwest corner of the valley, southwest of the city centers of Calexico and El Centro where ground motions were highest. Although there are few strong motion recordings in the very western part of the area, the recordings that do exist indicate that ground motions were on the order of 0.3 to 0.6g where the majority of liquefaction occurrences were found. More distant liquefaction occurrences, at Fites Road southwest of Brawley and along Rosita Canal northwest of Holtville were triggered where ground motions were about 0.2 g. Damage to roads was associated mainly with liquefaction of sandy river deposits beneath bridge approach fills, and in some cases liquefaction within the fills. Liquefaction damage to canal and drain levees was not always accompanied by vented sand, but the nature of the damage leads the authors to infer that liquefaction was involved in the majority of observed cases. Liquefaction-related damage to several public facilities - Calexico Waste Water Treatment Plant, Fig Lagoon levee system, and Sunbeam Lake Dam in particular - appears to be extensive. The cost to repair these facilities to prevent future liquefaction damage will likely be prohibitive. As such, it is likely that liquefaction will recur at these facilities during the next large earthquake in this area.

Hydrothermal liquefaction pathways for low-nitrogen biocrude from wet algae

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tanzella, Francis; Lim, Jin-Ping

Our SRI International (SRI) team has developed a new two-step hydrothermal liquefaction (HTL) process to convert wet algal biomass into biocrude oil. The first step in the process (low-temperature HTL or HTL1) yields crude oil but, most importantly, it selectively dissolves nitrogen-containing compounds in the aqueous phase. Once the oil and the aqueous phase are separated, the low-nitrogen soft solids left behind can be taken to the second step (high-temperature HTL or HTL2) for full conversion to biocrude. HTL2 will hence yield low-nitrogen biocrude, which can be hydro-processed to yield transportation fuels. The expected high carbon yield and low nitrogenmore » content can lead to a transportation fuel from algae that avoids two problems common to existing algae-to-fuel processes: (1) poisoning of the hydro-processing catalyst; and (2) inefficient conversion of algae-to-liquid fuels. The process we studied would yield a new route to strategic energy production from domestic sources.« less

A case study of liquefaction risk analysis based on the thickness and depth of the liquefaction layer using CPT and electric resistivity data in the Hinode area, Itako City, Ibaraki Prefecture, Japan

NASA Astrophysics Data System (ADS)

Jinguuji, Motoharu; Toprak, Selcuk

2017-12-01

The Hinode area of Itako City in Ibaraki Prefecture, Japan, suffered some of the most severe liquefaction damage of any areas in the Great Eastern Japan Earthquake in 2011. This liquefaction damage has been investigated by Itako City, as well as by universities and research institutes in Japan. The National Institute of Advanced Industrial Science and Technology (AIST) has carried out numerous investigations along the Tone River, and in particular, intensive surveys were done in the Hinode area. We have conducted a risk analysis based on the thickness and depth of the liquefaction layer measured using cone penetration testing (CPT) data and electric resistivity data obtained in the Hinode area. The distribution of the risk estimated from CPT at 143 points, and that obtained from analysis of the resistivity survey data, agreed with the distribution of actual damage. We also carried out conventional risk analyses method using the liquefaction resistance factor (FL) and liquefaction potential index (PL) methods with CPT data. The results show high PL values over the entire area, but their distribution did not agree well with actual damage in some parts of the study area. Because the analysis of the thickness and depth of the liquefaction layer, using geophysical prospecting methods, can cover a widespread area, this method will be very useful in investigating liquefaction risk, especially for gas and water pipelines.

Liquefaction of the Used Creosote-Treated Wood in the Presence of Phenol and Its Application to Phenolic Resin

Treesearch

Nubuo Shiraishi; Chung-Yun Hse

2000-01-01

A limited initial study was made to evaluate liquefaction of creosote-treated southern pine wood sawdust with liquefaction of birch wood powder as a control. The objective was to assess the feasibility of using creosote-treated southern pine wood as a raw material for the-formulation-of-phenol-based resin adhesives. The liquefaction was conducted in the presence of...

Age and significance of earthquake-induced liquefaction near Vancouver, British Columbia, Canada

USGS Publications Warehouse

Clague, J.J.; Naesgaard, E.; Nelson, A.R.

1997-01-01

In late 1994, sand dykes, large sand blows, and deformed strata were exposed in the walls of an excavation at Annacis Island on the Fraser River delta near Vancouver, British Columbia. The features record liquefaction during a large earthquake about 1700 years ago; this was perhaps the largest earthquake to affect the Vancouver area in the last 3500 years. Similar, less well-dated features have been reported from several other sites on the Fraser delta and may be products of the same earthquake. Three radiocarbon ages that closely delimit the time of liquefaction on Annacis Island are similar to the most precise radiocarbon ages on coseismically subsided marsh soils at estuaries in southern Washington and Oregon. Both the liquefaction and the subsidence may have been produced by a single great plate-boundary earthquake at the Cascadia subduction zone. Alternatively, liquefaction at Annacis Island may have been caused by a large crustal or subcrustal earthquake of about the same age as a plate-boundary earthquake farther west. The data from Annacis Island and other sites on the Fraser delta suggest that earthquakes capable of producing extensive liquefaction in this area are rare events. Further, liquefaction analysis using historical seismicity suggests that current assessment procedures may overestimate liquefaction risk.

Liquefaction of Saturated Soil and the Diffusion Equation

NASA Astrophysics Data System (ADS)

Sawicki, Andrzej; Sławińska, Justyna

2015-06-01

The paper deals with the diffusion equation for pore water pressures with the source term, which is widely promoted in the marine engineering literature. It is shown that such an equation cannot be derived in a consistent way from the mass balance and the Darcy law. The shortcomings of the artificial source term are pointed out, including inconsistencies with experimental data. It is concluded that liquefaction and the preceding process of pore pressure generation and the weakening of the soil skeleton should be described by constitutive equations within the well-known framework of applied mechanics. Relevant references are provided

Study on Correlation Between Shear Wave Velocity and Ground Properties for Ground Liquefaction Investigation of Silts

NASA Astrophysics Data System (ADS)

Che, Ailan; Luo, Xianqi; Qi, Jinghua; Wang, Deyong

Shear wave velocity (Vs) of soil is one of the key parameters used in assessment of liquefaction potential of saturated soils in the base with leveled ground surface; determination of shear module of soils used in seismic response analyses. Such parameter can be experimentally obtained from laboratory soil tests and field measurements. Statistical relation of shear wave velocity with soil properties based on the surface wave survey investigation, and resonant column triaxial tests, which are taken from more than 14 sites within the depth of 10 m under ground surface, is obtained in Tianjin (China) area. The relationship between shear wave velocity and the standard penetration test N value (SPT-N value) of silt and clay in the quaternary formation are summarized. It is an important problem to research the effect of shear wave velocity on liquefaction resistance of saturated silts (sandy loams) for evaluating liquefaction resistance. According the results of cyclic triaxial tests, a correlation between liquefaction resistance and shear wave velocity is presented. The results are useful for ground liquefaction investigation and the evaluation of liquefaction resistance.

Liquefaction features interpreted as seismites in the Pleistocene fluvio-lacustrine deposits of the Neuquén Basin (Northern Patagonia)

NASA Astrophysics Data System (ADS)

Moretti, M.; Ronchi, A.

2011-04-01

Superbly exposed soft-sediment deformation structures in Pleistocene fluvio-lacustrine deposits along the southern border of the depression area called Bajo de Añelo (Departamento de Añelo, Neuquén Basin) have been analysed. In the study area, five stratigraphic sections were measured in detail: facies distributions and stacking patterns show that these sediments result from the interaction between fluvial and lacustrine systems, represented by cross-bedded and rippled strata, and varved deposits. The lateral extent of the deformation is some hundred metres and the deformed bed involves the lower-mid part of the 30-metre-thick succession. Deformation affects about 1.5 m of coarse-grained sand, fine-grained sand and rare gravel alternations. The base and top of the deformed layer are defined by planar surfaces: undeformed beds of similar thickness, lithology and facies to the deformed layer occur above and below. Deformation is represented by a complex vertical succession of disturbed layers: each layer shows a general load-structure morphology. It can be described as a multilayered unstable density gradient system: in each bed a partial gravitational re-adjustment occurred after liquefaction. Unequal loading related to lateral variation of both bed thickness and grain packing and porosity is a probable additional driving force that can be described in the undeformed beds. Trigger mechanism recognition for the observed liquefaction features can be based on the study of the geometry of deformed beds and on facies analysis results. Two key factors drive our interpretation: (1) the occurrence of undeformed beds below and above the deformed bed; (2) deformed and undeformed beds showing the same sedimentological features. These field data allow us to exclude the action of internal erosive and/or sedimentary processes (such as overloading, wave action, etc.) as possible trigger agents for liquefaction since deformation is totally absent in beds with similar sedimentary features. Furthermore, each internal erosive and/or sedimentary process can be discussed and easily excluded by analysing its specific signature in the geological record. Having excluded every possible internal trigger (autokinetic processes), the observed liquefaction effects can reasonably be interpreted as seismically induced (allokinetic trigger). From this point of view, this deformed bed is an important record of seismic activity in this sector of the Neuquén Basin during the Pleistocene.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goldsmith, M.W.; Forbes, I.A.; Turnage, J.C.

The potential of new and future energy technologies is discussed, with information provided on availability, technical and economic feasibility, and limitations due to the form of the energy. Energy sources not presently in use (i.e., shale oil, garbage, geothermal, wind, tidal, breeder reactors, ocean thermal gradients, solar energy, and fusion) are expected to supply only 10 to 15% of the Nation's energy requirements in the year 2000. The following chapters are included: Energy Use and Supply; Extending Chemical Fuel Resources, which covers oil shale and tar sands, coal gasification and liquefaction, garbage, and biomass energy; Harnessing the Forces of Nature,more » which describes geothermal, tidal, hydro, wind, and solar energy; New Nuclear Technology (e.g., converter reactors, breeder reactors, fusion by magnetic confinement, and laser fusion); and Improving Energy Production Efficiency, with discussions on energy storage, MHD (magnetohydrodynamics), and combined cycles. (64 references) (BYB)« less

Efficiency enhancement for natural gas liquefaction with CO2 capture and sequestration through cycles innovation and process optimization

NASA Astrophysics Data System (ADS)

Alabdulkarem, Abdullah

Liquefied natural gas (LNG) plants are energy intensive. As a result, the power plants operating these LNG plants emit high amounts of CO2 . To mitigate global warming that is caused by the increase in atmospheric CO2, CO2 capture and sequestration (CCS) using amine absorption is proposed. However, the major challenge of implementing this CCS system is the associated power requirement, increasing power consumption by about 15--25%. Therefore, the main scope of this work is to tackle this challenge by minimizing CCS power consumption as well as that of the entire LNG plant though system integration and rigorous optimization. The power consumption of the LNG plant was reduced through improving the process of liquefaction itself. In this work, a genetic algorithm (GA) was used to optimize a propane pre-cooled mixed-refrigerant (C3-MR) LNG plant modeled using HYSYS software. An optimization platform coupling Matlab with HYSYS was developed. New refrigerant mixtures were found, with savings in power consumption as high as 13%. LNG plants optimization with variable natural gas feed compositions was addressed and the solution was proposed through applying robust optimization techniques, resulting in a robust refrigerant which can liquefy a range of natural gas feeds. The second approach for reducing the power consumption is through process integration and waste heat utilization in the integrated CCS system. Four waste heat sources and six potential uses were uncovered and evaluated using HYSYS software. The developed models were verified against experimental data from the literature with good agreement. Net available power enhancement in one of the proposed CCS configuration is 16% more than the conventional CCS configuration. To reduce the CO2 pressurization power into a well for enhanced oil recovery (EOR) applications, five CO2 pressurization methods were explored. New CO2 liquefaction cycles were developed and modeled using HYSYS software. One of the developed liquefaction cycles using NH3 as a refrigerant resulted in 5% less power consumption than the conventional multi-stage compression cycle. Finally, a new concept of providing the CO2 regeneration heat is proposed. The proposed concept is using a heat pump to provide the regeneration heat as well as process heat and CO2 liquefaction heat. Seven configurations of heat pumps integrated with CCS were developed. One of the heat pumps consumes 24% less power than the conventional system or 59% less total equivalent power demand than the conventional system with steam extraction and CO2 compression.

Probabilistic liquefaction triggering based on the cone penetration test

USGS Publications Warehouse

Moss, R.E.S.; Seed, R.B.; Kayen, R.E.; Stewart, J.P.; Tokimatsu, K.

2005-01-01

Performance-based earthquake engineering requires a probabilistic treatment of potential failure modes in order to accurately quantify the overall stability of the system. This paper is a summary of the application portions of the probabilistic liquefaction triggering correlations proposed recently proposed by Moss and co-workers. To enable probabilistic treatment of liquefaction triggering, the variables comprising the seismic load and the liquefaction resistance were treated as inherently uncertain. Supporting data from an extensive Cone Penetration Test (CPT)-based liquefaction case history database were used to develop a probabilistic correlation. The methods used to measure the uncertainty of the load and resistance variables, how the interactions of these variables were treated using Bayesian updating, and how reliability analysis was applied to produce curves of equal probability of liquefaction are presented. The normalization for effective overburden stress, the magnitude correlated duration weighting factor, and the non-linear shear mass participation factor used are also discussed.

Helium refrigeration system for hydrogen liquefaction applications

NASA Astrophysics Data System (ADS)

Nair, J. Kumar, Sr.; Menon, RS; Goyal, M.; Ansari, NA; Chakravarty, A.; Joemon, V.

2017-02-01

Liquid hydrogen around 20 K is used as cold moderator for generating “cold neutron beam” in nuclear research reactors. A cryogenic helium refrigeration system is the core upon which such hydrogen liquefaction applications are built. A thermodynamic process based on reversed Brayton cycle with two stage expansion using high speed cryogenic turboexpanders (TEX) along with a pair of compact high effectiveness process heat exchangers (HX), is well suited for such applications. An existing helium refrigeration system, which had earlier demonstrated a refrigeration capacity of 470 W at around 20 K, is modified based on past operational experiences and newer application requirements. Modifications include addition of a new heat exchanger to simulate cryogenic process load and two other heat exchangers for controlling the temperatures of helium streams leading out to the application system. To incorporate these changes, cryogenic piping inside the cold box is suitably modified. This paper presents process simulation, sizing of new heat exchangers as well as fabrication aspects of the modified cryogenic process piping.

Effect of hydrothermal liquefaction aqueous phase recycling on bio-crude yields and composition.

PubMed

Biller, Patrick; Madsen, René B; Klemmer, Maika; Becker, Jacob; Iversen, Bo B; Glasius, Marianne

2016-11-01

Hydrothermal liquefaction (HTL) is a promising thermo-chemical processing technology for the production of biofuels but produces large amounts of process water. Therefore recirculation of process water from HTL of dried distillers grains with solubles (DDGS) is investigated. Two sets of recirculation on a continuous reactor system using K2CO3 as catalyst were carried out. Following this, the process water was recirculated in batch experiments for a total of 10 rounds. To assess the effect of alkali catalyst, non-catalytic HTL process water recycling was performed with 9 recycle rounds. Both sets of experiments showed a large increase in bio-crude yields from approximately 35 to 55wt%. The water phase and bio-crude samples from all experiments were analysed via quantitative gas chromatography-mass spectrometry (GC-MS) to investigate their composition and build-up of organic compounds. Overall the results show an increase in HTL conversion efficiency and a lower volume, more concentrated aqueous by-product following recycling. Copyright © 2016 Elsevier Ltd. All rights reserved.

Evaluation of emerging factors blocking filtration of high-adjunct-ratio wort.

PubMed

Ma, Ting; Zhu, Linjiang; Zheng, Feiyun; Li, Yongxian; Li, Qi

2014-08-20

Corn starch has become a common adjunct for beer brewing in Chinese breweries. However, with increasing ratio of corn starch, problems like poor wort filtration performance arise, which will decrease production capacity of breweries. To solve this problem, factors affecting wort filtration were evaluated, such as the size of corn starch particle, special yellow floats formed during liquefaction of corn starch, and residual substance after liquefaction. The effects of different enzyme preparations including β-amylase and β-glucanase on filtration rate were also evaluated. The results indicate that the emerging yellow floats do not severely block filtration, while the fine and uniform-shape corn starch particle and its incompletely hydrolyzed residue after liquefaction are responsible for filtration blocking. Application of β-amylase preparation increased the filtration rate of liquefied corn starch. This study is useful for our insight into the filtration blocking problem arising in the process of high-adjunct-ratio beer brewing and also provides a feasible solution using enzyme preparations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singh, S. P.N.; Peterson, G. R.

Coal beneficiation is a generic term used for processes that prepare run-of-mine coal for specific end uses. It is also referred to as coal preparation or coal cleaning and is a means of reducing the sulfur and the ash contents of coal. Information is presented regarding current and potential coal beneficiation processes. Several of the processes reviewed, though not yet commercial, are at various stages of experimental development. Process descriptions are provided for these processes commensurate with the extent of information and time available to perform the evaluation of these processes. Conceptual process designs, preliminary cost estimates, and economic evaluationsmore » are provided for the more advanced (from a process development hierarchy viewpoint) processes based on production levels of 1500 and 15,000 tons/day (maf) of cleaned product coal. Economic evaluations of the coal preparation plants are conducted for several project financing schemes and at 12 and 15% annual after-tax rates of return on equity capital. A 9% annual interest rate is used on the debt fraction of the plant capital. Cleaned product coal prices are determined using the discounted cash flow procedure. The study is intended to provide information on publicly known coal beneficiation processes and to indicate the relative costs of various coal beneficiation processes. Because of severe timeconstraints, several potential coal beneficiation processes are not evaluated in great detail. It is recommended that an additional study be conducted to complement this study and to more fully appreciate the potentially significant role of coal beneficiation in the clean burning of coal.« less

Record of seismotectonic events in siliceous cyanobacterial sediments (Magadi cherts), Lake Magadi, Kenya

NASA Astrophysics Data System (ADS)

Behr, H.-J.; Röhricht, C.

The Quaternary sediments of Lake Magadi in the Kenya Rift include large volumes of chert. Before their lithification, these siliceous sediments underwent very strong deformation, as recorded by diapirism with pillow-chert mounds, extrusion along dykes and fault ramps, horizontal liquefaction slides with brecciation, slumping, as well as petee-, flow- and shear structures. Eugster (1969) considered these structures to have resulted from desiccation of Na-silicate precipitates (magadiite) that were deposited over wide areas and were several metres thick. Magadiite can remain soft over long periods; therefore, these ``Magadi-type cherts'' are called the type examples of inorganic cherts. However, field observations and microbiological studies of the cherts show that real inorganic cherts are rare at the type locality of Magadi-type cherts. Most of the cherts are older than the High Magadi Beds and developed from flat-topped calcareous bioherms of Pleurocapsa, Gloecocapsa, and other coccoid cyanobacteria, thinly bedded filamentous microbial mats, stromatolites, bacterial slimes, diatoms, Dascladiacea colonies and other organic matter. Silicification occurred from a silicasol via opal-A to opal-C with final recrystallisation to a chert of quartzine composition. The metabolic processes of cyanobacteria controlled the pH and influenced the dissolution-precipitation mechanism. Collapse, liquefaction and extrusion of the pre-lithified siliceous matrix was caused by seismotectonic rift activity, which activated fault scarplets and large-scale dyke systems. It led to liquefaction and other earthquake-induced structures along the fault ramps and on tilted blocks. Concentrated silicasols were generated by the interaction of alkaline waters with volcanic detritus, coupled with biochemical processes. After liquefaction and extrusion, the material solidified by spontaneous crystallisation in an environment that was characterised by highly variable pH and salinity. The Lake Magadi basin is a remarkable example of sedimentation in a continuously seismotectonically active basin. This paper presents a first description of the micro-organisms in Magadi-type cherts, the silicification process, and the deformation that occurred still in the putty-like state before lithification.

High Temperature Chemistry of Aromatic Hydrocarbons. Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, Lawrence T.

The primary goal of this research was to uncover the principal reaction channels available to polycyclic aromatic hydrocarbons (PAHs) at high temperatures in the gas phase and to establish the factors that determine which channels will be followed in varying circumstances. New structure-property relationships for PAHs were also studied. The efficient production of clean energy from fossil fuels will remain a major component of the DOE mission until alternative sources of energy eventually displace coal and petroleum. Hydrocarbons constitute the most basic class of compounds in all of organic chemistry, and as the dominant species in fossil fuels, they figuremore » prominently into the programs of the DOE. Much is already known about the normal chemistry of hydrocarbons under ambient conditions, but far less is known about their intrinsic chemistry at temperatures close to those reached during combustion. An understanding of the fundamental molecular transformations, rearrangements, and interconversions of PAHs at high temperatures in the gas phase, as revealed by careful studies on small, well-designed, molecular systems, provides insights into the underlying chemistry of many important processes that are more complex, such as the generation of energy by the combustion of fossil fuels, the uncatalyzed gasification and liquefaction of coal, the production of fullerenes in fuel-rich flames, and the formation of soot and carcinogenic pollutants in smoke (e.g., benzo[a]pyrene). The rational control of any of these processes, whether it be the optimization of a desirable process or the minimization of an undesirable one, requires a clear knowledge of the basic chemistry that governs the fate of the species involved. Advances in chemistry at the most fundamental level come about primarily from the discovery of new reactions and from new insights into how reactions occur. Harnessing that knowledge is the key to new technologies. The recent commercialization of a combustion synthesis of C 60 and other fullerenes depended critically on a knowledge of hydrocarbon reactions at high temperatures in the gas phase, and the research supported by this project enabled further advances in the realm of carbon-rich materials.« less

Multisensor and Multispectral Approach in Documenting and Analyzing Liquefaction Hazard using Remote Sensing

NASA Astrophysics Data System (ADS)

Oommen, T.; Baise, L. G.; Gens, R.; Prakash, A.; Gupta, R. P.

2008-12-01

Seismic liquefaction is the loss of strength of soil due to shaking that leads to various ground failures such as lateral spreading, settlements, tilting, and sand boils. It is important to document these failures after earthquakes to advance our study of when and where liquefaction occurs. The current approach of mapping these failures by field investigation teams suffers due to the inaccessibility to some of the sites immediately after the event, short life of some of these failures, difficulties in mapping the aerial extent of the failure, incomplete coverage etc. After the 2001 Bhuj earthquake (India), researchers, using the Indian remote sensing satellite, illustrated that satellite remote sensing can provide a synoptic view of the terrain and offer unbiased estimates of liquefaction failures. However, a multisensor (data from different sensors onboard of the same or different satellites) and multispectral (data collected in different spectral regions) approach is needed to efficiently document liquefaction incidences and/or its potential of occurrence due to the possibility of a particular satellite being located inappropriately to image an area shortly after an earthquake. The use of SAR satellite imagery ensures the acquisition of data in all weather conditions at day and night as well as information complimentary to the optical data sets. In this study, we analyze the applicability of the various satellites (Landsat, RADARSAT, Terra-MISR, IRS-1C, IRS-1D) in mapping liquefaction failures after the 2001 Bhuj earthquake using Support Vector Data Description (SVDD). The SVDD is a kernel based nonparametric outlier detection algorithm inspired by the Support Vector Machines (SVMs), which is a new generation learning algorithm based on the statistical learning theory. We present the applicability of SVDD for unsupervised change-detection studies (i.e. to identify post-earthquake liquefaction failures). The liquefaction occurrences identified from the different satellites using SVDD have been compared to the ground truth in terms of documented liquefaction failures by other researchers. We present the applicability and appropriateness of the various satellites and spectral regions for documenting liquefaction related failures. Results illustrate that the SVDD is a promising unsupervised change-detection algorithm, which can help in automating the documentation of earthquake induced liquefaction failures.

Simultaneous saccharification and fermentation of broken rice: an enzymatic extrusion liquefaction pretreatment for Chinese rice wine production.

PubMed

Li, Hongyan; Jiao, Aiquan; Xu, Xueming; Wu, Chunsen; Wei, Benxi; Hu, Xiuting; Jin, Zhengyu; Tian, Yaoqi

2013-08-01

Broken rice, pretreated by enzymatic extrusion liquefaction, was used to produce Chinese rice wine by simultaneous saccharification and fermentation (SSF) process in this study. The study compared the novel process and traditional process for Chinese rice wine fermentation utilizing broken rice and head rice, respectively. With the optimum extrusion parameters (barrel temperature, 98 °C; moisture content, 42% and amylase concentration, 1‰), 18% (v/v at 20 °C) alcoholic degree, 37.66% fermentation recovery and 93.63% fermentation efficiency were achieved, indicating enzymatic extrusion-processed rice wine from broken rice exhibited much higher fermentation rate and efficiency than traditional-processed rice wine from head rice during SSF. The starch molecule distribution data indicated that the alcoholic degree was related to the oligosaccharides' formation during enzymatic extrusion. Sum of amino acid (AA) in the extrusion-processed wine was 53.7% higher than that in the traditional one. These results suggest that the enzymatic extrusion pretreatment for broken rice is a feasible and alternative process in the fermentation of Chinese rice wine.

Effect of multi-stream heat exchanger on performance of natural gas liquefaction with mixed refrigerant

NASA Astrophysics Data System (ADS)

Chang, Ho-Myung; Lim, Hye Su; Choe, Kun Hyung

2012-12-01

A thermodynamic study is carried out to investigate the effect of multi-stream heat exchanger on the performance of natural gas (NG) liquefaction with mixed refrigerant (MR). A cold stream (low-pressure MR) is in thermal contact with opposite flow of two hot streams (high-pressure MR and NG feed) at the same time. In typical process simulation with commercial software (such as Aspen HYSYS®), the liquefaction performance is estimated with a method of minimum temperature approach, simply assuming that two hot streams have the same temperature. In this study, local energy balance equations are rigorously solved with temperature-dependent properties of MR and NG feed, and are linked to the thermodynamic cycle analysis. The figure of merit (FOM) is quantitatively examined in terms of UA (the product of overall heat transfer coefficient and heat exchange area) between respective streams. In a single-stage MR process, it is concluded that the temperature profile from HYSYS is difficult to realize in practice, and the FOM value from HYSYS is an over-estimate, but can be closely achieved with a proper heat-exchanger design. It is also demonstrated that there exists a unique optimal ratio in three UA's, and no direct heat exchanger between hot streams is recommended.

Current knowledge on agarolytic enzymes and the industrial potential of agar-derived sugars.

PubMed

Yun, Eun Ju; Yu, Sora; Kim, Kyoung Heon

2017-07-01

Agar is a major cell wall carbohydrate of red macroalgae (Rhodophyta). Sugars derived from agar, such as agarooligosaccharides (AOSs), neoagarooligosaccharides (NAOSs), neoagarobiose (NAB), and 3,6-anhydro-L-galactose (L-AHG), possess various physiological activities. These agar-derived sugars can be produced by hydrolysis using chemicals or agarolytic enzymes. Despite the industrial potential of agar-derived sugars, their application has been hampered mainly due to the absence of efficient processes for the liquefaction and saccharification of agar. In this review, we have focused on strategies for producing high value-added sugars from agarose via chemical or enzymatic liquefaction and enzymatic saccharification. The liquefaction of agarose is a key step for preventing gelling and increasing the solubility of agarose in water by prehydrolyzing agarose into AOSs or NAOSs. For the industrial use of agar-derived sugars, AOS, NAOS, NAB, and L-AHG can be used as functional biomaterials owing to their physiological activities such as antiinflammation, skin whitening, and moisturizing. Recently, it was reported that AHG could be considered as a new anticariogenic sugar to replace xylitol. This review provides a comprehensive overview of processes for the hydrolysis of agar or agarose to produce high value-added sugars and the industrial application of these sugars.

Liquefaction Potential for Soil Deposits in Muscat, Oman

NASA Astrophysics Data System (ADS)

El Hussain, I. W.; Deif, A.; Girgis, M.; Al-Rawas, G.; Mohamed, A.; Al-Jabri, K.; Al-Habsi, Z.

2015-12-01

Muscat is located in the northeastern part of Oman on a narrow strip between Oman coast and Oman Mountains, which is the place for at least four earthquakes of order of 5.2 magnitude in the last 1300 years. The near surface geology of Muscat varies from hard rocks in the eastern, southern and western parts to dense and lose sediments in the middle and northern parts. Liquefaction occurs in saturated cohesionless soils when its shear strength decreased to zero due to the increase of pore pressure. More than 500 boreholes in Muscat area were examined for their liquefaction susceptibility based on the soil characteristics data. Only soils susceptible to liquefaction are further considered for liquefaction hazard assessment. Liquefaction occurs if the cyclic stress ratio (CSR) caused by the earthquake is higher than the cyclic resistance ratio (CRR) of the soil. CSR values were evaluated using PGA values at the surface obtained from previously conducted seismic hazard and microzonation studies. CRR for Muscat region is conducted using N values of SPT tests from numerous borehole data and the shear wave velocity results from 99 MASW surveys over the entire region. All the required corrections are conducted to get standardized (N1) 60 values, to correct shear-wave velocity, and scale the results for Mw 6.0 instead of the proposed 7.5 (magnitude scaling factor). Liquefaction hazard maps are generated using the minimum factor of safety (FS) at each site as a representative of the FS against liquefaction at that location. Results indicate that under the current level of seismic hazard, liquefaction potential is possible at few sites along the northern coast where alluvial soils and shallow ground water table are present. The expected soft soil settlement is also evaluated at each liquefiable site.

Comparison of SPT and V s-based liquefaction analyses: a case study in Erciş (Van, Turkey)

NASA Astrophysics Data System (ADS)

Akkaya, İsmail; Özvan, Ali; Akin, Mutluhan; Akin, Müge K.; Övün, Uğur

2017-12-01

Liquefaction which is one of the most destructive ground deformations occurs during an earthquake in saturated or partially saturated silty and sandy soils, which may cause serious damages such as settlement and tilting of structures due to shear strength loss of soils. Standard (SPT) and cone (CPT) penetration tests as well as the shear wave velocity (V s)-based methods are commonly used for the determination of liquefaction potential. In this research, it was aimed to compare the SPT and V s-based liquefaction analysis methods by generating different earthquake scenarios. Accordingly, the Erciş residential area, which was mostly affected by the 2011 Van earthquake (M w = 7.1), was chosen as the model site. Erciş (Van, Turkey) and its surroundings settle on an alluvial plain which consists of silty and sandy layers with shallow groundwater level. Moreover, Çaldıran, Erciş-Kocapınar and Van Fault Zones are the major seismic sources of the region which have a significant potential of producing large magnitude earthquakes. After liquefaction assessments, the liquefaction potential in the western part of the region and in the coastal regions nearby the Lake Van is found to be higher than the other locations. Thus, it can be stated that the soil tightness and groundwater level dominantly control the liquefaction potential. In addition, the lateral spreading and sand boiling spots observed after the 23rd October 2011 Van earthquake overlap the scenario boundaries predicted in this study. Eventually, the use of V s-based liquefaction analysis in collaboration with the SPT results is quite advantageous to assess the rate of liquefaction in a specific area.

Comparison of SPT and V s-based liquefaction analyses: a case study in Erciş (Van, Turkey)

NASA Astrophysics Data System (ADS)

Akkaya, İsmail; Özvan, Ali; Akin, Mutluhan; Akin, Müge K.; Övün, Uğur

2018-02-01

Liquefaction which is one of the most destructive ground deformations occurs during an earthquake in saturated or partially saturated silty and sandy soils, which may cause serious damages such as settlement and tilting of structures due to shear strength loss of soils. Standard (SPT) and cone (CPT) penetration tests as well as the shear wave velocity ( V s)-based methods are commonly used for the determination of liquefaction potential. In this research, it was aimed to compare the SPT and V s-based liquefaction analysis methods by generating different earthquake scenarios. Accordingly, the Erciş residential area, which was mostly affected by the 2011 Van earthquake ( M w = 7.1), was chosen as the model site. Erciş (Van, Turkey) and its surroundings settle on an alluvial plain which consists of silty and sandy layers with shallow groundwater level. Moreover, Çaldıran, Erciş-Kocapınar and Van Fault Zones are the major seismic sources of the region which have a significant potential of producing large magnitude earthquakes. After liquefaction assessments, the liquefaction potential in the western part of the region and in the coastal regions nearby the Lake Van is found to be higher than the other locations. Thus, it can be stated that the soil tightness and groundwater level dominantly control the liquefaction potential. In addition, the lateral spreading and sand boiling spots observed after the 23rd October 2011 Van earthquake overlap the scenario boundaries predicted in this study. Eventually, the use of V s-based liquefaction analysis in collaboration with the SPT results is quite advantageous to assess the rate of liquefaction in a specific area.

Low temperature engineering applied to lunar in-situ resource utilization

NASA Technical Reports Server (NTRS)

Zhang, Burt; Chui, Talso; Croonquist, Arvid

2005-01-01

In support of NASA's Exploration Mission low-temperature scientists and engineers have investigated the process of extracting volatile materials from the lunar regolith, their purification/liquefaction, and storage.

Predicted liquefaction of East Bay fills during a repeat of the 1906 San Francisco earthquake

USGS Publications Warehouse

Holzer, T.L.; Blair, J.L.; Noce, T.E.; Bennett, M.J.

2006-01-01

Predicted conditional probabilities of surface manifestations of liquefaction during a repeat of the 1906 San Francisco (M7.8) earthquake range from 0.54 to 0.79 in the area underlain by the sandy artificial fills along the eastern shore of San Francisco Bay near Oakland, California. Despite widespread liquefaction in 1906 of sandy fills in San Francisco, most of the East Bay fills were emplaced after 1906 without soil improvement to increase their liquefaction resistance. They have yet to be shaken strongly. Probabilities are based on the liquefaction potential index computed from 82 CPT soundings using median (50th percentile) estimates of PGA based on a ground-motion prediction equation. Shaking estimates consider both distance from the San Andreas Fault and local site conditions. The high probabilities indicate extensive and damaging liquefaction will occur in East Bay fills during the next M ??? 7.8 earthquake on the northern San Andreas Fault. ?? 2006, Earthquake Engineering Research Institute.

Use of microalgae to recycle nutrients in aqueous phase derived from hydrothermal liquefaction process.

PubMed

Leng, Lijian; Li, Jun; Wen, Zhiyou; Zhou, Wenguang

2018-05-01

Hydrothermal liquefaction (HTL) of microalgae biomass generates an aqueous phase (AP) byproduct with limited energy value. Recycling the AP solution as a source of nutrients for microalgae cultivation provides an opportunity for a cost-effective production of HTL based biofuel and algal biomass feedstock for HTL, allowing a closed-loop biofuel production in microalgae HTL biofuel system. This paper aims to provide a comprehensive overview of characteristics of AP and its nutrients recycling for algae production. Inhibitory effects resulted from the toxic compounds in AP and alleviation strategies are discussed. Copyright © 2018 Elsevier Ltd. All rights reserved.

Hydrothermal Liquefaction Treatment Preliminary Hazard Analysis Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowry, Peter P.; Wagner, Katie A.

A preliminary hazard assessment was completed during February 2015 to evaluate the conceptual design of the modular hydrothermal liquefaction treatment system. The hazard assessment was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. This analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affectingmore » the public.« less

Post Hoc Analysis of Passive Cavitation Imaging for Classification of Histotripsy-Induced Liquefaction in Vitro.

PubMed

Bader, Kenneth B; Haworth, Kevin J; Maxwell, Adam D; Holland, Christy K

2018-01-01

Histotripsy utilizes focused ultrasound to generate bubble clouds for transcutaneous tissue liquefaction. Bubble activity maps are under development to provide image guidance and monitor treatment progress. The aim of this paper was to investigate the feasibility of using plane wave B-mode and passive cavitation images to be used as binary classifiers of histotripsy-induced liquefaction. Prostate tissue phantoms were exposed to histotripsy pulses over a range of pulse durations (5- ) and peak negative pressures (12-23 MPa). Acoustic emissions were recorded during the insonation and beamformed to form passive cavitation images. Plane wave B-mode images were acquired following the insonation to detect the hyperechoic bubble cloud. Phantom samples were sectioned and stained to delineate the liquefaction zone. Correlation between passive cavitation and plane wave B-mode images and the liquefaction zone was assessed using receiver operating characteristic (ROC) curve analysis. Liquefaction of the phantom was observed for all the insonation conditions. The area under the ROC (0.94 versus 0.82), accuracy (0.90 versus 0.83), and sensitivity (0.81 versus 0.49) was greater for passive cavitation images relative to B-mode images ( ) along the azimuth of the liquefaction zone. The specificity was greater than 0.9 for both imaging modalities. These results demonstrate a stronger correlation between histotripsy-induced liquefaction and passive cavitation imaging compared with the plane wave B-mode imaging, albeit with limited passive cavitation image range resolution.

Post-cyclic behavior of low plasticity silt under full and limited liquefaction using triaxial compression testing.

DOT National Transportation Integrated Search

2010-02-01

During an earthquake, liquefaction does not happen all the time. It depends on the duration and magnitude of the earthquake and the properties (with relationship to resistance of liquefaction) of the low plasticity silt. Under low duration or magnitu...

46 CFR 148.450 - Cargoes subject to liquefaction.

Code of Federal Regulations, 2013 CFR

2013-10-01

... in this section— (1) Cargo subject to liquefaction means a material that is subject to moisture migration and subsequent liquefaction if shipped with moisture content in excess of the transportable moisture limit. (2) Moisture migration is the movement of moisture by settling and consolidation of a...

46 CFR 148.450 - Cargoes subject to liquefaction.

Code of Federal Regulations, 2014 CFR

2014-10-01

... in this section— (1) Cargo subject to liquefaction means a material that is subject to moisture migration and subsequent liquefaction if shipped with moisture content in excess of the transportable moisture limit. (2) Moisture migration is the movement of moisture by settling and consolidation of a...

46 CFR 148.450 - Cargoes subject to liquefaction.

Code of Federal Regulations, 2012 CFR

2012-10-01

... in this section— (1) Cargo subject to liquefaction means a material that is subject to moisture migration and subsequent liquefaction if shipped with moisture content in excess of the transportable moisture limit. (2) Moisture migration is the movement of moisture by settling and consolidation of a...