Measurements of high energy photons in Z-pinch experiments on primary test stand.

PubMed

Si, Fenni; Zhang, Chuanfei; Xu, Rongkun; Yuan, Xi; Huang, Zhanchang; Xu, Zeping; Ye, Fan; Yang, Jianlun; Ning, Jiamin; Hu, Qingyuan; Zhu, Xuebin

2015-08-01

High energy photons are measured for the first time in wire-array Z-pinch experiments on the Primary Test Stand (PTS) which delivers a current up to 8 MA with a rise time of 70 ns. A special designed detecting system composed of three types of detectors is used to measure the average energy, intensity, and pulse waveform of high energy photons. Results from Pb-TLD (thermoluminescence dosimeter) detector indicate that the average energy is 480 keV (±15%). Pulse shape of high energy photons is measured by the photodiode detector consisted of scintillator coupled with a photodiode, and it is correlated with soft x-ray power by the same timing signal. Intensity is measured by both TLD and the photodiode detector, showing good accordance with each other, and it is 10(10) cm(-2) (±20%) at 2 m in the horizontal direction. Measurement results show that high energy photons are mainly produced in pinch regions due to accelerated electrons. PTS itself also produces high energy photons due to power flow electrons, which is one order smaller in amplitude than those from pinch region.

High energy, high average power solid state green or UV laser

DOEpatents

Hackel, Lloyd A.; Norton, Mary; Dane, C. Brent

2004-03-02

A system for producing a green or UV output beam for illuminating a large area with relatively high beam fluence. A Nd:glass laser produces a near-infrared output by means of an oscillator that generates a high quality but low power output and then multi-pass through and amplification in a zig-zag slab amplifier and wavefront correction in a phase conjugator at the midway point of the multi-pass amplification. The green or UV output is generated by means of conversion crystals that follow final propagation through the zig-zag slab amplifier.

Real-Time Human Detection for Aerial Captured Video Sequences via Deep Models.

PubMed

AlDahoul, Nouar; Md Sabri, Aznul Qalid; Mansoor, Ali Mohammed

2018-01-01

Human detection in videos plays an important role in various real life applications. Most of traditional approaches depend on utilizing handcrafted features which are problem-dependent and optimal for specific tasks. Moreover, they are highly susceptible to dynamical events such as illumination changes, camera jitter, and variations in object sizes. On the other hand, the proposed feature learning approaches are cheaper and easier because highly abstract and discriminative features can be produced automatically without the need of expert knowledge. In this paper, we utilize automatic feature learning methods which combine optical flow and three different deep models (i.e., supervised convolutional neural network (S-CNN), pretrained CNN feature extractor, and hierarchical extreme learning machine) for human detection in videos captured using a nonstatic camera on an aerial platform with varying altitudes. The models are trained and tested on the publicly available and highly challenging UCF-ARG aerial dataset. The comparison between these models in terms of training, testing accuracy, and learning speed is analyzed. The performance evaluation considers five human actions (digging, waving, throwing, walking, and running). Experimental results demonstrated that the proposed methods are successful for human detection task. Pretrained CNN produces an average accuracy of 98.09%. S-CNN produces an average accuracy of 95.6% with soft-max and 91.7% with Support Vector Machines (SVM). H-ELM has an average accuracy of 95.9%. Using a normal Central Processing Unit (CPU), H-ELM's training time takes 445 seconds. Learning in S-CNN takes 770 seconds with a high performance Graphical Processing Unit (GPU).

Use of different rapid mixing devices for controlling the properties of magnetite nanoparticles produced by precipitation

NASA Astrophysics Data System (ADS)

Wei, Li; Hervé, Muhr; Edouard, Plasari

2012-03-01

Magnetite nanoparticles were precipitated by the classic Massart's method in a 2.5 L stirred tank reactor where the injection of reagent solutions was effectuated by different micro-mixers (T-tube and Hartridge-Roughton rapid mixing devices). The specific surface area, the average particle size and the particle size distribution were highly influenced by changing operating parameters. Laser Diffraction, BET adsorption, Energy-Dispersive X-ray Spectroscopy (EDX), Raman spectroscopy and Transmission Electron Microscopy (TEM) were used for characterizing magnetite nanoparticles. Especially, Hartridge-Roughton micromixer appears to be the most efficient mixing device for producing magnetite nanoparticles. The average particle size of magnetite nanoparticles prepared by Hartridge-Roughton rapid mixing device was less than 10 nm and the EDX and Raman spectroscopy shows that the particle purity is quite high.

Generation of 180 W average green power from a frequency-doubled picosecond rod fiber amplifier

DOE PAGES

Zhao, Zhi; Sheehy, Brian; Minty, Michiko

2017-03-29

Here, we report on the generation of 180 W average green power from a frequency-doubled picosecond rod fiber amplifier. In an Yb-doped fiber master-oscillator-power-amplifier system, 2.3-ps 704 MHz pulses are first amplified in small-core fibers and then in large-mode-area rod fibers to produce 270 W average infrared power with a high polarization extinction ratio and diffraction-limited beam quality. By carrying out frequency doubling in a lithium triborate (LBO) crystal, 180 W average green power is generated. To the best of our knowledge, this is the highest average green power achieved in fiber-based laser systems.

Observations of the Infrared Solar Spectrum from Space by the ATMOS Experiment

NASA Technical Reports Server (NTRS)

Abrams, M. C.; Goldman, A.; Gunson, M. R.; Rinsland, C. P.; Zander, R.

1999-01-01

The final flight of the Atmospheric Trace Molecule Spectroscopy experiment as part of the Atmospheric na Laboratory for Applications and Science (ATLAS-3) Space Shuttle mission in 1994 provided a new opportunity to measure broadband 625-4800/ cm, 2.1 - 16 micron infrared solar spectra at an unapodized resolution of 0.0l/ cm from space. The majority of the observations were obtained as exoatmospheric, of near Sun center, absorption spectra, which were later ratioed to grazing atmospheric measurements to compute the atmospheric transmission of the Earth's atmosphere and analyzed for vertical profiles of minor and trace gases. Relative to the SPACELAB-3 mission that produced 4800 high Sun spectra (which were averaged into four grand average spectra), the ATLAS-3 mission produced some 40,000 high Sun spectra (which have been similarly averaged) with an improvement in signal-to-noise ratio of a factor of 3-4 in the spectral region between 1000 and 4800/ cm. A brief description of the spectral calibration and spectral quality is given as well as the location of electronic archives of these spectra.

Evaluating average and atypical response in radiation effects simulations

NASA Astrophysics Data System (ADS)

Weller, R. A.; Sternberg, A. L.; Massengill, L. W.; Schrimpf, R. D.; Fleetwood, D. M.

2003-12-01

We examine the limits of performing single-event simulations using pre-averaged radiation events. Geant4 simulations show the necessity, for future devices, to supplement current methods with ensemble averaging of device-level responses to physically realistic radiation events. Initial Monte Carlo simulations have generated a significant number of extremal events in local energy deposition. These simulations strongly suggest that proton strikes of sufficient energy, even those that initiate purely electronic interactions, can initiate device response capable in principle of producing single event upset or microdose damage in highly scaled devices.

1997 Annual Tropical Cyclone Report

DTIC Science & Technology

1997-01-01

caused much loss of life and great destruction at their respective landfall sites in China andVietnam. Mainland Japan, the Ryukyu Islands, the Bonin ...Aside from passing through the Volcano Islands and the Bonin Islands of Japan, Nestor remained over water. Nestor did produce some high waves on...DYNAMIC AVERAGE ( DAVE ) A simple average of all dynamic forecast aids: NOGAPS (NGPS), Bracknell (EGRR), Japanese Typhoon Model (JTYM), JT92, FBAM, OTCM

Optimization of ultrasonic emulsification conditions for the production of orange peel essential oil nanoemulsions.

PubMed

Hashtjin, Adel Mirmajidi; Abbasi, Soleiman

2015-05-01

The aim of the present study was to investigate the influence of emulsifying conditions on some physical and rheological properties of orange peel essential oil (OPEO) in water nanoemulsions. In this regard, using the response surface methodology, the influence of ultrasonication conditions including sonication amplitude (70-100 %), sonication time (90-150 s) and process temperature (5-45 °C) on the mean droplets diameter (Z-average value), polydispersity index (PDI), and viscosity of the OPEO nanoemulsions was evaluated. In addition, the flow behavior and stability of selected nanoemulsions was evaluated during storage (up to 3 months) at different temperatures (5, 25 and 45 °C). Based on the results of the optimization, the optimum conditions for producing OPEO nanoemulsions (Z-average value 18.16 nm) were determined as 94 % (sonication amplitude), 138 s (sonication time) and 37 °C (process temperature). Moreover, analysis of variance (ANOVA) showed high coefficients of determination values (R (2) > 0.95) for the response surface models of the energy input and Z-average. In addition, the flow behavior of produced nanoemulsions was Newtonian, and the effect of time and storage temperature as well as their interactions on the Z-average value was highly significant (P < 0.0001).

Improving timing sensitivity in the microhertz frequency regime: limits from PSR J1713+0747 on gravitational waves produced by supermassive black hole binaries

NASA Astrophysics Data System (ADS)

Perera, B. B. P.; Stappers, B. W.; Babak, S.; Keith, M. J.; Antoniadis, J.; Bassa, C. G.; Caballero, R. N.; Champion, D. J.; Cognard, I.; Desvignes, G.; Graikou, E.; Guillemot, L.; Janssen, G. H.; Karuppusamy, R.; Kramer, M.; Lazarus, P.; Lentati, L.; Liu, K.; Lyne, A. G.; McKee, J. W.; Osłowski, S.; Perrodin, D.; Sanidas, S. A.; Sesana, A.; Shaifullah, G.; Theureau, G.; Verbiest, J. P. W.; Taylor, S. R.

2018-07-01

We search for continuous gravitational waves (CGWs) produced by individual supermassive black hole binaries in circular orbits using high-cadence timing observations of PSR J1713+0747. We observe this millisecond pulsar using the telescopes in the European Pulsar Timing Array with an average cadence of approximately 1.6 d over the period between 2011 April and 2015 July, including an approximately daily average between 2013 February and 2014 April. The high-cadence observations are used to improve the pulsar timing sensitivity across the gravitational wave frequency range of 0.008-5μHz. We use two algorithms in the analysis, including a spectral fitting method and a Bayesian approach. For an independent comparison, we also use a previously published Bayesian algorithm. We find that the Bayesian approaches provide optimal results and the timing observations of the pulsar place a 95 per cent upper limit on the sky-averaged strain amplitude of CGWs to be ≲3.5 × 10-13 at a reference frequency of 1 μHz. We also find a 95 per cent upper limit on the sky-averaged strain amplitude of low-frequency CGWs to be ≲1.4 × 10-14 at a reference frequency of 20 nHz.

Improving timing sensitivity in the microhertz frequency regime: limits from PSR J1713+0747 on gravitational waves produced by super-massive black-hole binaries

NASA Astrophysics Data System (ADS)

Perera, B. B. P.; Stappers, B. W.; Babak, S.; Keith, M. J.; Antoniadis, J.; Bassa, C. G.; Caballero, R. N.; Champion, D. J.; Cognard, I.; Desvignes, G.; Graikou, E.; Guillemot, L.; Janssen, G. H.; Karuppusamy, R.; Kramer, M.; Lazarus, P.; Lentati, L.; Liu, K.; Lyne, A. G.; McKee, J. W.; Osłowski, S.; Perrodin, D.; Sanidas, S. A.; Sesana, A.; Shaifullah, G.; Theureau, G.; Verbiest, J. P. W.; Taylor, S. R.

2018-05-01

We search for continuous gravitational waves (CGWs) produced by individual super-massive black-hole binaries (SMBHBs) in circular orbits using high-cadence timing observations of PSR J1713+0747. We observe this millisecond pulsar using the telescopes in the European Pulsar Timing Array (EPTA) with an average cadence of approximately 1.6 days over the period between April 2011 and July 2015, including an approximately daily average between February 2013 and April 2014. The high-cadence observations are used to improve the pulsar timing sensitivity across the GW frequency range of 0.008 - 5 μHz. We use two algorithms in the analysis, including a spectral fitting method and a Bayesian approach. For an independent comparison, we also use a previously published Bayesian algorithm. We find that the Bayesian approaches provide optimal results and the timing observations of the pulsar place a 95 per cent upper limit on the sky-averaged strain amplitude of CGWs to be ≲ 3.5 × 10-13 at a reference frequency of 1 μHz. We also find a 95 per cent upper limit on the sky-averaged strain amplitude of low-frequency CGWs to be ≲ 1.4 × 10-14 at a reference frequency of 20 nHz.

Experimental study on temperature profile of fixed - bed gasification of oil-palm fronds

NASA Astrophysics Data System (ADS)

Atnaw, Samson M.; Sulaiman, Shaharin A.; Moni, M. Nazmi Z.

2012-06-01

Currently the world's second largest palm oil producer Malaysia produces large amount of oil palm biomass each year. The abundance of the biomass introduces a challenge to utilize them as main feedstock for heat and energy generation. Although some oil palm parts and derivatives like empty fruit bunch and fibre have been commercialized as fuel, less attention has been given to oil palm fronds (OPF). Initial feasibility and characterization studies of OPF showed that it is highly feasible as fuel for gasification to produce high value gaseous fuel or syngas. This paper discusses the experimental gasification attempt carried out on OPF using a 50 kW lab scale downdraft gasifier and its results. The conducted study focused on the temperature distributions within the reactor and the characteristics of the dynamic temperature profile for each temperature zones during operation. OPF feedstock of one cubic inch in individual size with 15% average moisture content was utilized. An average pyrolysis zone temperature of 324°Cand an average oxidation zone temperature of 796°Cwere obtained over a total gasification period of 74 minutes. A maximum oxidation zone temperature of 952°Cwas obtained at 486 lpm inlet air flow rate and 10 kg/hr feedstock consumption rate. Stable bluish flare was produced for more than 70% of the total gasification time. The recorded temperature profiles produced closely similar patterns with the temperature profiles recorded from the gasification of woody materials. Similar temperature profile was obtained comparing the results from OPF gasification with that of woody biomass. Furthermore, the successful ignition of the syngas produced from OPF gasification ascertained that OPF indeed has a higher potential as gasification feedstock. Hence, more detailed studies need to be done for better understanding in exploiting the biomass as a high prospect alternative energy solution. In addition, a study of the effect of initial moisture content of OPF feedstock on the temperature distribution profile along the gasifier bed showed that initial moisture content of feedstock in the range of 15% gives satisfactory result, while experiment with feedstock having higher moisture content resulted in lower zone temperature values.

Influence of Surface Roughness on Polymer Drag Reduction

DTIC Science & Technology

2007-11-30

paint (High Build Semi-Gloss 97-130, Aquapon ) with glass bead grit. The particles were tightly packed producing a sand grain type roughness. Based on the... Aquapon High Build Semi-Gloss Epoxy 97-130) with glass bead grit blown into the epoxy. The particles were tightly packed giving an average roughness height

Kilohertz Pulse Repetition Frequency Slab Ti:sapphire Lasers with High Average Power (10 W)

NASA Astrophysics Data System (ADS)

Wadsworth, William J.; Coutts, David W.; Webb, Colin E.

1999-11-01

High-average-power broadband 780-nm slab Ti:sapphire lasers, pumped by a kilohertz pulse repetition frequency copper vapor laser (CVL), were demonstrated. These lasers are designed for damage-free power scaling when pumped by CVL s configured for maximum output power (of order 100 W) but with poor beam quality ( M 2 300 ). A simple Brewster-angled slab laser side pumped by a CVL produced 10-W average power (1.25-mJ pulses at 8 kHz) with 4.2-ns FWHM pulse duration at an absolute efficiency of 15% (68-W pump power). Thermal lensing in the Brewster slab laser resulted in multitransverse mode output, and pump absorption was limited to 72% by the maximum doping level for commercially available Ti:sapphire (0.25%). A slab laser with a multiply folded zigzag path was therefore designed and implemented that produced high-beam-quality (TEM 00 -mode) output when operated with cryogenic cooling and provided a longer absorption path for the pump. Excessive scattering of the Ti:sapphire beam at the crystal surfaces limited the efficiency of operation for the zigzag laser, but fluorescence diagnostic techniques, gain measurement, and modeling suggest that efficient power extraction ( 15 W TEM 00 , 23% efficiency) from this laser would be possible for crystals with an optical quality surface polish.

A Comparative Study of Automated Infrasound Detectors - PMCC and AFD with Analyst Review.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Junghyun; Hayward, Chris; Zeiler, Cleat

Automated detections calculated by the progressive multi-channel correlation (PMCC) method (Cansi, 1995) and the adaptive F detector (AFD) (Arrowsmith et al., 2009) are compared to the signals identified by five independent analysts. Each detector was applied to a four-hour time sequence recorded by the Korean infrasound array CHNAR. This array was used because it is composed of both small (<100 m) and large (~1000 m) aperture element spacing. The four hour time sequence contained a number of easily identified signals under noise conditions that have average RMS amplitudes varied from 1.2 to 4.5 mPa (1 to 5 Hz), estimated withmore » running five-minute window. The effectiveness of the detectors was estimated for the small aperture, large aperture, small aperture combined with the large aperture, and full array. The full and combined arrays performed the best for AFD under all noise conditions while the large aperture array had the poorest performance for both detectors. PMCC produced similar results as AFD under the lower noise conditions, but did not produce as dramatic an increase in detections using the full and combined arrays. Both automated detectors and the analysts produced a decrease in detections under the higher noise conditions. Comparing the detection probabilities with Estimated Receiver Operating Characteristic (EROC) curves we found that the smaller value of consistency for PMCC and the larger p-value for AFD had the highest detection probability. These parameters produced greater changes in detection probability than estimates of the false alarm rate. The detection probability was impacted the most by noise level, with low noise (average RMS amplitude of 1.7 mPa) having an average detection probability of ~40% and high noise (average RMS amplitude of 2.9 mPa) average detection probability of ~23%.« less

Ultrahigh molecular weight aromatic siloxane polymers

NASA Technical Reports Server (NTRS)

Ludwick, L. M.

1982-01-01

The condensation of a diol with a silane in toluene yields a silphenylene-siloxane polymer. The reaction of stiochiometric amounts of the diol and silane produced products with molecular weights in the range 2.0 - 6.0 x 10 to the 5th power. The molecular weight of the product was greatly increased by a multistep technique. The methodology for synthesis of high molecular weight polymers using a two step procedure was refined. Polymers with weight average molecular weights in excess of 1.0 x 10 to the 6th power produced by this method. Two more reactive silanes, bis(pyrrolidinyl)dimethylsilane and bis(gamma butyrolactam)dimethylsilane, are compared with the dimethyleminodimethylsilane in ability to advance the molecular weight of the prepolymer. The polymers produced are characterized by intrinsic viscosity in tetrahydrofuran. Weight and number average molecular weights and polydispersity are determined by gel permeation chromatography.

Geochemical signatures and magmatic stability of terrestrial impact produced zircon

NASA Astrophysics Data System (ADS)

Wielicki, Matthew M.; Harrison, T. Mark; Schmitt, Axel K.

2012-03-01

Understanding the role of impacts on early Earth has major implications to near surface conditions, but the apparent lack of preserved terrestrial craters > 2 Ga does not allow a direct sampling of such events. Ion microprobe U-Pb ages, REE abundances and Ti-in-zircon thermometry for impact produced zircon are reported here. These results from terrestrial impactites, ranging in age from ~ 35 Ma to ~ 2 Ga, are compared with the detrital Hadean zircon population from Western Australia. Such comparisons may provide the only terrestrial constraints on the role of impacts during the Hadean and early Archean, a time predicted to have a high bolide flux. Ti-in-zircon thermometry indicates an average of 773 °C for impact-produced zircon, ~ 100 °C higher than the average for Hadean zircon crystals. The agreement between whole-rock based zircon saturation temperatures for impactites and Ti-in-zircon thermometry (at aTiO2 = 1) implies that Ti-in-zircon thermometry record actual crystallization temperatures for impact melts. Zircon saturation modeling of Archean crustal rock compositions undergoing thermal excursions associated with the Late Heavy Bombardment predicts equally high zircon crystallization temperatures. The lack of such thermal signatures in the Hadean zircon record implies that impacts were not a dominant mechanism of producing the preserved Hadean detrital zircon record.

Performance summary on a high power dense plasma focus x-ray lithography point source producing 70 nm line features in AlGaAs microcircuits

NASA Astrophysics Data System (ADS)

Petr, Rodney; Bykanov, Alexander; Freshman, Jay; Reilly, Dennis; Mangano, Joseph; Roche, Maureen; Dickenson, Jason; Burte, Mitchell; Heaton, John

2004-08-01

A high average power dense plasma focus (DPF), x-ray point source has been used to produce ˜70 nm line features in AlGaAs-based monolithic millimeter-wave integrated circuits (MMICs). The DPF source has produced up to 12 J per pulse of x-ray energy into 4π steradians at ˜1 keV effective wavelength in ˜2 Torr neon at pulse repetition rates up to 60 Hz, with an effective x-ray yield efficiency of ˜0.8%. Plasma temperature and electron concentration are estimated from the x-ray spectrum to be ˜170 eV and ˜5.1019 cm-3, respectively. The x-ray point source utilizes solid-state pulse power technology to extend the operating lifetime of electrodes and insulators in the DPF discharge. By eliminating current reversals in the DPF head, an anode electrode has demonstrated a lifetime of more than 5 million shots. The x-ray point source has also been operated continuously for 8 h run times at 27 Hz average pulse recurrent frequency. Measurements of shock waves produced by the plasma discharge indicate that overpressure pulses must be attenuated before a collimator can be integrated with the DPF point source.

The Condition of New York City High Schools: Examining Trends and Looking toward the Future. Data Brief

ERIC Educational Resources Information Center

Kemple, James J.

2013-01-01

Until the turn of the 21st century, high school graduation rates in New York City hovered at or below 50 percent, much lower than state and national averages. There was widespread agreement about the need to reform the City's high schools and produce better results for students. This paper presents an independent analysis of how the high school…

The Condition of New York City High Schools: Examining Trends and Looking toward the Future. Technical Appendices

ERIC Educational Resources Information Center

Kemple, James J.

2013-01-01

Until the turn of the 21st century, high school graduation rates in New York City hovered at or below 50 percent, much lower than state and national averages. There was widespread agreement about the need to reform the City's high schools and produce better results for students. These technical appendices presented in chart form, provide…

Modulated Pulsed Laser Sources for Imaging Lidars

DTIC Science & Technology

2007-10-01

doped PM fiber . The ytterbium ions in the fiber are cladding-pumped to their excited states using four, 6-Watt multimode lasers at 976 nm. Yh-dop...next amplified using a fiber amplifier to an average power of 10-15 Watts. A highly efficient, periodically poled nonlinear optical material will be...establish the feasibility of both pulsing a 1064 nm laser to produce enough average power to successfully seed a Yb- doped fiber amplifier so it will

Development of a small-sized generator of ozonated water using an electro-conductive diamond electrode.

PubMed

Sekido, Kota; Kitaori, Noriyuki

2008-12-01

A small-sized generator of ozonated water was developed using an electro-conductive diamond. We studied the optimum conditions for producing ozonated water. As a result, we developed a small-sized generator of ozonated water driven by a dry-cell for use in the average household. This generator was easily able to produce ozonated water with an ozone concentration (over 4 mg/L) sufficient for disinfection. In addition, we verified the high disinfecting performance of the water produced in an actual hospital.

Characterization of Aerosols of Titanium Dioxide Nanoparticles Following Three Generation Methods Using an Optimized Aerosolization System Designed for Experimental Inhalation Studies

PubMed Central

Pujalté, Igor; Serventi, Alessandra; Noël, Alexandra; Dieme, Denis; Haddad, Sami; Bouchard, Michèle

2017-01-01

Nanoparticles (NPs) can be released in the air in work settings, but various factors influence the exposure of workers. Controlled inhalation experiments can thus be conducted in an attempt to reproduce real-life exposure conditions and assess inhalation toxicology. Methods exist to generate aerosols, but it remains difficult to obtain nano-sized and stable aerosols suitable for inhalation experiments. The goal of this work was to characterize aerosols of titanium dioxide (TiO2) NPs, generated using a novel inhalation system equipped with three types of generators—a wet collision jet nebulizer, a dry dust jet and an electrospray aerosolizer—with the aim of producing stable aerosols with a nano-diameter average (<100 nm) and monodispersed distribution for future rodent exposures and toxicological studies. Results showed the ability of the three generation systems to provide good and stable dispersions of NPs, applicable for acute (continuous up to 8 h) and repeated (21-day) exposures. In all cases, the generated aerosols were composed mainly of small aggregates/agglomerates (average diameter <100 nm) with the electrospray producing the finest (average diameter of 70–75 mm) and least concentrated aerosols (between 0.150 and 2.5 mg/m3). The dust jet was able to produce concentrations varying from 1.5 to 150 mg/m3, and hence, the most highly concentrated aerosols. The nebulizer collision jet aerosolizer was the most versatile generator, producing both low (0.5 mg/m3) and relatively high concentrations (30 mg/m3). The three optimized generators appeared suited for possible toxicological studies of inhaled NPs. PMID:29051446

Development of a high average current polarized electron source with long cathode operational lifetime

DOE Office of Scientific and Technical Information (OSTI.GOV)

C. K. Sinclair; P. A. Adderley; B. M. Dunham

Substantially more than half of the electromagnetic nuclear physics experiments conducted at the Continuous Electron Beam Accelerator Facility of the Thomas Jefferson National Accelerator Facility (Jefferson Laboratory) require highly polarized electron beams, often at high average current. Spin-polarized electrons are produced by photoemission from various GaAs-based semiconductor photocathodes, using circularly polarized laser light with photon energy slightly larger than the semiconductor band gap. The photocathodes are prepared by activation of the clean semiconductor surface to negative electron affinity using cesium and oxidation. Historically, in many laboratories worldwide, these photocathodes have had short operational lifetimes at high average current, and havemore » often deteriorated fairly quickly in ultrahigh vacuum even without electron beam delivery. At Jefferson Lab, we have developed a polarized electron source in which the photocathodes degrade exceptionally slowly without electron emission, and in which ion back bombardment is the predominant mechanism limiting the operational lifetime of the cathodes during electron emission. We have reproducibly obtained cathode 1/e dark lifetimes over two years, and 1/e charge density and charge lifetimes during electron beam delivery of over 2?105???C/cm2 and 200 C, respectively. This source is able to support uninterrupted high average current polarized beam delivery to three experimental halls simultaneously for many months at a time. Many of the techniques we report here are directly applicable to the development of GaAs photoemission electron guns to deliver high average current, high brightness unpolarized beams.« less

Morphological control of three-dimensional carbon nanotube anode for high-capacity lithium-ion battery

NASA Astrophysics Data System (ADS)

Kang, Chiwon; Lee, Hoo-Jeong

2018-05-01

In this paper, we report the results of modulating the processing conditions (mainly, temperature) of a two-step method consisting of sputtering deposition of a Ni catalytic layer and chemical vapor deposition (CVD) of carbon nanotubes (CNTs) on a three-dimensional (3D)-structured Cu mesh to control the morphology of CNTs for advanced Li-ion battery (LIB) applications. We disclosed that CNT growth at a low temperature (700 °C) produced small-diameter CNTs (CNT_S) with an average diameter of ∼20 nm, while that at a high temperature (750 °C) produced large-diameter CNTs (CNT_L) with an average diameter of 200–300 nm. The high-resolution transmission electron microscopy (HR-TEM) and Raman analyses manifested poorly crystalline CNTs for both samples. CNTS showed a specific capacity of 476 mAh g‑1, which is ∼176% superior to that of CNTL (271 mAh g‑1) and ∼128% higher than the theoretical capacity of the state-of-the-art graphites and recently reported nanostructured carbon-based anode materials.

Breathe Plant Breathe: A Study of CO2 conversion in plants

NASA Astrophysics Data System (ADS)

Weiss, M.

2016-12-01

Some of the research that I have found is that plants with green oxygen produce the most oxygen.Green oxygen is the Some examples of plants like this are spouts (such as the sweet pea, buckwheat, and sunflower.) Some of the other plants are the snake plant and the areca plant. These three plants are most commonly used in households to produce more oxygen when needed. Looking at a few more websites I saw that the plants do not produce oxygen at night because they have no light to transfer within photosynthesis. Some other information that I got was that plants with thick leaves or have a lot of leaves on them produce more oxygen. Some examples of this are the peace lily and the bamboo palm. Since these plants have thick and big leaves they have more photosynthesis cells and can produce more oxygen. In conclusion, my hypothesis was supported. The plant that converted the most CO2 was the pothos. I learned that if you need house plants to help create oxygen, one of the best ones would be a pothos because of its fast conversion rate. As a result the plant that converted the most carbon dioxide into oxygen was the pothos. With an average start of 5259.6, and average finish of 1463, and an average change of 3796.6 The Fern had an: average change of: 5205, average start of: 6564.6, and an average finish of: 1500 The Aloe had an: average change of: 4409.2, average start of: 7707.6, and an average finish of: 3298.4 And the Panda had an: average change of: 4821.8 average start of: 6971.2, and an average finish of:2149

Solar abundances as derived from solar energetic particles

NASA Technical Reports Server (NTRS)

Stone, E. C.

1989-01-01

Recent studies have shown that there are well defined average abundances of heavy (Z above 2) solar energetic particles (SEPs), with variations in the acceleration and propagation producing a systematic flare-to-flare fractionation that depends on the charge per unit mass of the ion. Correcting the average SEP abundances for this fractionation yields SEP-derived coronal abundances for 20 elements. High-resolution SEP studies have also provided isotopic abundances for five elements. SEP-derived abundances indicate that elements with high first ionization potentials (greater than 10 eV) are depleted in the corona relative to the photosphere and provide new information on the solar abundance of C and Ne-22.

Induction of chromatin damage and distribution of isochromatid breaks in human fibroblast cells exposed to heavy ions

NASA Technical Reports Server (NTRS)

Kawata, Tetsuya; Ito, Hisao; Motoori, Ken; Ueda, Takuya; Shigematsu, Naoyuki; Furusawa, Yoshiya; Durante, Marco; George, Kerry; Wu, Honglu; Cucinotta, Francis A.

2002-01-01

The frequency of chromatid breaks and the distribution of isochromatid breaks were measured in G2-phase normal human fibroblasts prematurely condensed a short time after exposure to low- or high-LET radiations. The average number of isochromatid breaks from a single particle traversal increased with increasing LET values, while the average number of chromatid-type breaks appeared to reach a plateau. The distribution of isochromatid breaks after high-LET iron particles exposure was overdispersed compared to gamma-rays, indicating that a single iron particle traversal through a cell nucleus can produce multiple isochromatid breaks.

Induction of chromatin damage and distribution of isochromatid breaks in human fibroblast cells exposed to heavy ions.

PubMed

Kawata, Tetsuya; Ito, Hisao; Motoori, Ken; Ueda, Takuya; Shigematsu, Naoyuki; Furusawa, Yoshiya; Durante, Marco; George, Kerry; Wu, Honglu; Cucinotta, Francis A

2002-12-01

The frequency of chromatid breaks and the distribution of isochromatid breaks were measured in G2-phase normal human fibroblasts prematurely condensed a short time after exposure to low- or high-LET radiations. The average number of isochromatid breaks from a single particle traversal increased with increasing LET values, while the average number of chromatid-type breaks appeared to reach a plateau. The distribution of isochromatid breaks after high-LET iron particles exposure was overdispersed compared to gamma-rays, indicating that a single iron particle traversal through a cell nucleus can produce multiple isochromatid breaks.

Insights from the genome of a high alkaline cellulase producing Aspergillus fumigatus strain obtained from Peruvian Amazon rainforest.

PubMed

Paul, Sujay; Zhang, Angel; Ludeña, Yvette; Villena, Gretty K; Yu, Fengan; Sherman, David H; Gutiérrez-Correa, Marcel

2017-06-10

Here, we report the complete genome sequence of a high alkaline cellulase producing Aspergillus fumigatus strain LMB-35Aa isolated from soil of Peruvian Amazon rainforest. The genome is ∼27.5mb in size, comprises of 228 scaffolds with an average GC content of 50%, and is predicted to contain a total of 8660 protein-coding genes. Of which, 6156 are with known function; it codes for 607 putative CAZymes families potentially involved in carbohydrate metabolism. Several important cellulose degrading genes, such as endoglucanase A, endoglucanase B, endoglucanase D and beta-glucosidase, are also identified. The genome of A. fumigatus strain LMB-35Aa represents the first whole sequenced genome of non-clinical, high cellulase producing A. fumigatus strain isolated from forest soil. Copyright © 2017 Elsevier B.V. All rights reserved.

Downscaled soil moisture from SMAP evaluated using high density observations

USDA-ARS?s Scientific Manuscript database

Recently, a soil moisture downscaling algorithm based on a regression relationship between daily temperature changes and daily average soil moisture was developed to produce an enhanced spatial resolution on soil moisture product for the Advanced Microwave Scanning Radiometer–EOS (AMSR-E) satellite ...

High-resolution microendoscopy for esophageal cancer screening in China: A cost-effectiveness analysis.

PubMed

Hur, Chin; Choi, Sung Eun; Kong, Chung Yin; Wang, Gui-Qi; Xu, Hong; Polydorides, Alexandros D; Xue, Li-Yan; Perzan, Katherine E; Tramontano, Angela C; Richards-Kortum, Rebecca R; Anandasabapathy, Sharmila

2015-05-14

To study the cost-effectiveness of high-resolution microendoscopy (HRME) in an esophageal squamous cell carcinoma (ESCC) screening program in China. A decision analytic Markov model of ESCC was developed. Separate model analyses were conducted for cohorts consisting of an average-risk population or a high-risk population in China. Hypothetical 50-year-old individuals were followed until age 80 or death. We compared three different strategies for both cohorts: (1) no screening; (2) standard endoscopic screening with Lugol's iodine staining; and (3) endoscopic screening with Lugol's iodine staining and an HRME. Model parameters were estimated from the literature as well as from GLOBOCAN, the Cancer Incidence and Mortality Worldwide cancer database. Health states in the model included non-neoplasia, mild dysplasia, moderate dysplasia, high-grade dysplasia, intramucosal carcinoma, operable cancer, inoperable cancer, and death. Separate ESCC incidence transition rates were generated for the average-risk and high-risk populations. Costs in Chinese currency were converted to international dollars (I$) and were adjusted to 2012 dollars using the Consumer Price Index. The main outcome measurements for this study were quality-adjusted life years (QALYs) and incremental cost-effectiveness ratio (ICER). For the average-risk population, the HRME screening strategy produced 0.043 more QALYs than the no screening strategy at an additional cost of I$646, resulting in an ICER of I$11808 per QALY gained. Standard endoscopic screening was weakly dominated. Among the high-risk population, when the HRME screening strategy was compared with the standard screening strategy, the ICER was I$8173 per QALY. For both the high-risk and average-risk screening populations, the HRME screening strategy appeared to be the most cost-effective strategy, producing ICERs below the willingness-to-pay threshold, I$23500 per QALY. One-way sensitivity analysis showed that, for the average-risk population, higher specificity of Lugol's iodine (> 40%) and lower specificity of HRME (< 70%) could make Lugol's iodine screening cost-effective. For the high-risk population, the results of the model were not substantially affected by varying the follow-up rate after Lugol's iodine screening, Lugol's iodine test characteristics (sensitivity and specificity), or HRME specificity. The incorporation of HRME into an ESCC screening program could be cost-effective in China. Larger studies of HRME performance are needed to confirm these findings.

Lateral distribution of high energy hadrons and gamma ray in air shower cores observed with emulsion chambers

NASA Technical Reports Server (NTRS)

Matano, T.; Machida, M.; Kawasumi, N.; Tsushima, I.; Honda, K.; Hashimoto, K.; Navia, C. E.; Matinic, N.; Aquirre, C.

1985-01-01

A high energy event of a bundle of electrons, gamma rays and hadronic gamma rays in an air shower core were observed. The bundles were detected with an emulsion chamber with thickness of 15 cm lead. This air shower is estimated to be initiated with a proton with energy around 10 to the 17th power to 10 to the 18th power eV at an altitude of around 100 gmc/2. Lateral distributions of the electromagnetic component with energy above 2 TeV and also the hadronic component of energy above 6 TeV of this air shower core were determined. Particles in the bundle are produced with process of the development of the nuclear cascade, the primary energy of each interaction in the cascade which produces these particles is unknown. To know the primary energy dependence of transverse momentum, the average products of energy and distance for various average energies of secondary particles are studied.

Bright betatron X-ray radiation from a laser-driven-clustering gas target

PubMed Central

Chen, L. M.; Yan, W. C.; Li, D. Z.; Hu, Z. D.; Zhang, L.; Wang, W. M.; Hafz, N.; Mao, J. Y.; Huang, K.; Ma, Y.; Zhao, J. R.; Ma, J. L.; Li, Y. T.; Lu, X.; Sheng, Z. M.; Wei, Z. Y.; Gao, J.; Zhang, J.

2013-01-01

Hard X-ray sources from femtosecond (fs) laser-produced plasmas, including the betatron X-rays from laser wakefield-accelerated electrons, have compact sizes, fs pulse duration and fs pump-probe capability, making it promising for wide use in material and biological sciences. Currently the main problem with such betatron X-ray sources is the limited average flux even with ultra-intense laser pulses. Here, we report ultra-bright betatron X-rays can be generated using a clustering gas jet target irradiated with a small size laser, where a ten-fold enhancement of the X-ray yield is achieved compared to the results obtained using a gas target. We suggest the increased X-ray photon is due to the existence of clusters in the gas, which results in increased total electron charge trapped for acceleration and larger wiggling amplitudes during the acceleration. This observation opens a route to produce high betatron average flux using small but high repetition rate laser facilities for applications. PMID:23715033

Joule heating at high latitudes

NASA Technical Reports Server (NTRS)

Foster, J. C.; St.-Maurice, J.-P.; Abreu, V. J.

1983-01-01

Calculations based on simultaneous observations of the electric field magnitude, and individual measurements of ion drift velocity and particle precipitation, over the lifetime of the AE-C satellite, are used to determine high latitude Joule heating. Conductivities produced by an averaged seasonal illumination were included with those calculated from particle precipitation. It is found that high latitude Joule heating occurs in an approximately oval pattern, and consists of dayside cleft, dawn and dusk sunward convection, and night sector heating regions. On average, heating in the cleft and dawn-dusk regions contributes the largest heat input, and there is no apparent difference between hemispheres for similar seasons. Joule heat input is 50 percent greater in summer than in winter, due primarily to the greater conductivity caused by solar production.

Multi-sensor image fusion algorithm based on multi-objective particle swarm optimization algorithm

NASA Astrophysics Data System (ADS)

Xie, Xia-zhu; Xu, Ya-wei

2017-11-01

On the basis of DT-CWT (Dual-Tree Complex Wavelet Transform - DT-CWT) theory, an approach based on MOPSO (Multi-objective Particle Swarm Optimization Algorithm) was proposed to objectively choose the fused weights of low frequency sub-bands. High and low frequency sub-bands were produced by DT-CWT. Absolute value of coefficients was adopted as fusion rule to fuse high frequency sub-bands. Fusion weights in low frequency sub-bands were used as particles in MOPSO. Spatial Frequency and Average Gradient were adopted as two kinds of fitness functions in MOPSO. The experimental result shows that the proposed approach performances better than Average Fusion and fusion methods based on local variance and local energy respectively in brightness, clarity and quantitative evaluation which includes Entropy, Spatial Frequency, Average Gradient and QAB/F.

Comprehensive characterization of glutamine synthetase-mediated selection for the establishment of recombinant CHO cells producing monoclonal antibodies.

PubMed

Noh, Soo Min; Shin, Seunghyeon; Lee, Gyun Min

2018-03-29

To characterize a glutamine synthetase (GS)-based selection system, monoclonal antibody (mAb) producing recombinant CHO cell clones were generated by a single round of selection at various methionine sulfoximine (MSX) concentrations (0, 25, and 50 μM) using two different host cell lines (CHO-K1 and GS-knockout CHO). Regardless of the host cell lines used, the clones selected at 50 μM MSX had the lowest average specific growth rate and the highest average specific production rates of toxic metabolic wastes, lactate and ammonia. Unlike CHO-K1, high producing clones could be generated in the absence of MSX using GS-knockout CHO with an improved selection stringency. Regardless of the host cell lines used, the clones selected at various MSX concentrations showed no significant difference in the GS, heavy chain, and light chain gene copies (P > 0.05). Furthermore, there was no correlation between the specific mAb productivity and these three gene copies (R 2  ≤ 0.012). Taken together, GS-mediated gene amplification does not occur in a single round of selection at a MSX concentration up to 50 μM. The use of the GS-knockout CHO host cell line facilitates the rapid generation of high producing clones with reduced production of lactate and ammonia in the absence of MSX.

Morphing Wings: A Study Using High-Fidelity Aerodynamic Shape Optimization

NASA Astrophysics Data System (ADS)

Curiale, Nathanael J.

With the aviation industry under pressure to reduce fuel consumption, morphing wings have the capacity to improve aircraft performance, thereby making a significant contribution to reversing climate change. Through high-fidelity aerodynamic shape optimization, various forms of morphing wings are assessed for a hypothetical regional-class aircraft. The framework used solves the Reynolds-averaged Navier-Stokes equations and utilizes a gradient-based optimization algorithm. Baseline geometries are developed through multipoint optimization, where the average drag coefficient is minimized over a range of flight conditions with additional dive constraints. Morphing optimizations are then performed, beginning with these baseline shapes. Five distinct types of morphing are investigated and compared. Overall, a theoretical fully adaptable wing produces roughly a 2% improvement in average performance, whereas trailing-edge morphing with a 27-point multipoint baseline results in just over a 1% improvement in average performance. Trailing-edge morphing proves to be more beneficial than leading-edge morphing, upper-surface morphing, and a conventional flap.

High-resolution observations of the polar magnetic fields of the sun

NASA Technical Reports Server (NTRS)

Lin, H.; Varsik, J.; Zirin, H.

1994-01-01

High-resolution magnetograms of the solar polar region were used for the study of the polar magnetic field. In contrast to low-resolution magnetograph observations which measure the polar magnetic field averaged over a large area, we focused our efforts on the properties of the small magnetic elements in the polar region. Evolution of the filling factor (the ratio of the area occupied by the magnetic elements to the total area) of these magnetic elements, as well as the average magnetic field strength, were studied during the maximum and declining phase of solar cycle 22, from early 1991 to mid-1993. We found that during the sunspot maximum period, the polar regions were occupied by about equal numbers of positive and negative magnetic elements, with equal average field strength. As the solar cycle progresses toward sunspot minimum, the magnetic field elements in the polar region become predominantly of one polarity. The average magnetic field of the dominant polarity elements also increases with the filling factor. In the meanwhile, both the filling factor and the average field strength of the non-dominant polarity elements decrease. The combined effects of the changing filling factors and average field strength produce the observed evolution of the integrated polar flux over the solar cycle. We compared the evolutionary histories of both filling factor and average field strength, for regions of high (70-80 deg) and low (60-70 deg) latitudes. For the south pole, we found no significant evidence of difference in the time of reversal. However, the low-latitude region of the north pole did reverse polarity much earlier than the high-latitude region. It later showed an oscillatory behavior. We suggest this may be caused by the poleward migration of flux from a large active region in 1989 with highly imbalanced flux.

Microstructural studies of nanocrystalline α-alumina powder produced from Al13-cluster

NASA Astrophysics Data System (ADS)

Harun Al Rashid Megat Ahmad, Megat; Aziz Mohamed, Abdul; Ibrahim, Azmi; Seman Mahmood, Che; Giri Rachman Putra, Edy; Jamro, Rafhayudi; Kasim, Razali; Rawi Muhammad Zin, Muhammad

2007-12-01

Nanocrystalline alumina powder was produced from calcinations of Al13-oxalate precipitates at 1100 °C. A nearly normal distribution of agglomerated alumina powder was obtained with an average particle size of about 1 μm. XRD measurement confirmed that the alumina produced was of high purity and crystalline α-phase. Microstructural features of both the precipitates and alumina obtained were studied using the small angle neutron scattering (SANS) technique. SANS examinations show the formation of microstructures in the alumina powder of mass fractals type with dimension of ˜2.8 indicative of low intra-granular porosity.

Obtaining the variance of gametic diversity with genomic models

USDA-ARS?s Scientific Manuscript database

It may be possible to use information about the variability among gametes (spermatozoa and ova) to select parents that are more likely than average to produce offspring with extremely high or low breeding values. In this study, statistical formulae were developed to calculate variability among gamet...

Carbon Stripper Foils Used in the Los Alamos PSR

NASA Astrophysics Data System (ADS)

Borden, M.; Plum, M. A.; Sugai, I.

1997-05-01

Carbon stripper foils produced by the modified controlled ACDC arc discharge method (mCADAD) at the Institute for Nuclear Study by Dr. Isao Sugai have been tested and used for high current 800-MeV beam production in the Proton Storage Ring (PSR) since 1993. Two approximately 110 μg/cm2 foils are sandwiched together to produce an equivalent 220 μg/cm^2 foil. The combined foil is supported by 4-5 μm diameter carbon fibers attached to an aluminum frame. These foils have survived as long as five months during PSR normal beam production of near 70 μA on target average current. Typical life-times of other foils vary from seven to fourteen days with lower on-target average current. Beam loss data also indicate that Sugai's foils have slower shrinkage rates than other foils. Equipment has been assembled and used to produce foils by the mCADAD method at Los Alamos. These foils will be tested during 1997 operation.

Estimation of Uncertainties in the Global Distance Test (GDT_TS) for CASP Models.

PubMed

Li, Wenlin; Schaeffer, R Dustin; Otwinowski, Zbyszek; Grishin, Nick V

2016-01-01

The Critical Assessment of techniques for protein Structure Prediction (or CASP) is a community-wide blind test experiment to reveal the best accomplishments of structure modeling. Assessors have been using the Global Distance Test (GDT_TS) measure to quantify prediction performance since CASP3 in 1998. However, identifying significant score differences between close models is difficult because of the lack of uncertainty estimations for this measure. Here, we utilized the atomic fluctuations caused by structure flexibility to estimate the uncertainty of GDT_TS scores. Structures determined by nuclear magnetic resonance are deposited as ensembles of alternative conformers that reflect the structural flexibility, whereas standard X-ray refinement produces the static structure averaged over time and space for the dynamic ensembles. To recapitulate the structural heterogeneous ensemble in the crystal lattice, we performed time-averaged refinement for X-ray datasets to generate structural ensembles for our GDT_TS uncertainty analysis. Using those generated ensembles, our study demonstrates that the time-averaged refinements produced structure ensembles with better agreement with the experimental datasets than the averaged X-ray structures with B-factors. The uncertainty of the GDT_TS scores, quantified by their standard deviations (SDs), increases for scores lower than 50 and 70, with maximum SDs of 0.3 and 1.23 for X-ray and NMR structures, respectively. We also applied our procedure to the high accuracy version of GDT-based score and produced similar results with slightly higher SDs. To facilitate score comparisons by the community, we developed a user-friendly web server that produces structure ensembles for NMR and X-ray structures and is accessible at http://prodata.swmed.edu/SEnCS. Our work helps to identify the significance of GDT_TS score differences, as well as to provide structure ensembles for estimating SDs of any scores.

Fungi in Ontario maple syrup & some factors that determine the presence of mold damage.

PubMed

Frasz, Samantha L; Miller, J David

2015-08-17

Maple syrup is a high value artisanal product produced mainly in Canada and a number of States primarily in the northeast USA. Mold growth (Wallemia sebi) on commercial product was first reported in syrup in 1908. Since then, few data have been published. We conducted a systematic examination for fungi in maple syrup from 68 producers from all of the syrup-producing areas of Ontario, Canada. The mean pH of the samples was pH 6.82, sugar content averaged 68.0±0.89 °Brix and aw averaged 0.841±0.011. Some 23 species of fungi were isolated based on morphology and molecular techniques. The most common fungus in the maple syrup samples was Eurotium herbariorum, followed by Penicillium chrysogenum, Aspergillus penicillioides, Aspergillus restrictus, Aspergillus versicolor and two species of Wallemia. Cladosporium cladosporioides was also common but only recovered when fungi known from high sugar substrates were also present in the mold damaged sample. The rarely reported yeast Citeromyces matrinsis was found in samples from three producers. There appear to be three potential causes for mold damage observed. High aw was associated with about one third of the mold damage. Independently, cold packing (bottling at ~25 °C) was a risk factor. However, syrup of good quality and quite low aw values was contaminated. We hypothesize that sanitation in the bottling line and other aspects of the bottling process may be partial explanations. Clarifying this requires further study. Copyright © 2015 Elsevier B.V. All rights reserved.

Controlling Hydrogen Embrittlement in Ultra-High Strength Steels

DTIC Science & Technology

2006-06-01

this tempering temperature, (5) finely distributed, partly coherent M2C (where M = 75 at.% Cr, 13 Fe and 12 Mo) in martensite , averaging 2 nm...states in a complex precipitation hardened martensitic microstructure and is susceptible to severe hydrogen embrittlement (HE) at threshold stress...repartitions to interstitial sites proximate to the highly stressed crack tip and, subsequently, may retrap at martensitic lath interfaces to produce substantial

Relative ion expansion velocity in laser-produced plasmas

NASA Technical Reports Server (NTRS)

Goldsmith, S.; Moreno, J. C.; Griem, H. R.; Cohen, Leonard; Richardson, M. C.

1988-01-01

The spectra of highly ionized titanium, Ti XIII through Ti XXI, and C VI Lyman lines were excited in laser-produced plasmas. The plasma was produced by uniformly irradiating spherical glass microballoons coated with thin layers of titanium and parylene. The 24-beam Omega laser system produced short, 0.6 ns, and high-intensity, 4 x 10 to the 14th W/sq cm, laser pulses at a wavelength of 351 nm. The measured wavelength for the 2p-3s Ti XIII resonance lines had an average shift of + 0.023 A relative to the C VI and Ti XX spectral lines. No shift was found between the C VI, Ti XIX, and Ti XX lines. The shift is attributed to a Doppler effect, resulting from a difference of (2.6 + or - 0.2) x 10 to the 7th cm/s in the expansion velocities of Ti XIX and Ti XX ions compared to Ti XIII ions.

Local sea surface temperatures add to extreme precipitation in northeast Australia during La Niña

NASA Astrophysics Data System (ADS)

Evans, Jason P.; Boyer-Souchet, Irène

2012-05-01

This study examines the role played by high sea surface temperatures around northern Australia, in producing the extreme precipitation which occurred during the strong La Niña in December 2010. These extreme rains produced floods that impacted almost 1,300,000 km2, caused billions of dollars in damage, led to the evacuation of thousands of people and resulted in 35 deaths. Through the use of regional climate model simulations the contribution of the observed high sea surface temperatures to the rainfall is quantified. Results indicate that the large-scale atmospheric circulation changes associated with the La Niña event, while associated with above average rainfall in northeast Australia, were insufficient to produce the extreme rainfall and subsequent flooding observed. The presence of high sea surface temperatures around northern Australia added ˜25% of the rainfall total.

High production of D-tagatose, a potential sugar substitute, using immobilized L-arabinose isomerase.

PubMed

Kim, P; Yoon, S H; Roh, H J; Choi, J H

2001-01-01

An L-arabinose isomerase of Escherichia coli was immobilized using covalent binding to agarose to produce D-tagatose, a bulking sweetener that can be economically used as a sugar substitute. The immobilized L-arabinose isomerase stably produced an average of 7.5 g-tagatose/L.day for 7 days with a productivity exceeding that of the free enzyme (0.47 vs 0.30 mg/U.day). Using a scaled-up immobilized enzyme system, 99.9 g-tagatose/L was produced from galactose with 20% equilibrium in 48 h. The process was repeated two more times with production of 104.1 and 103.5 g-tagatose/L. D-Tagatose production using an immobilized L-arabinose isomerase has a high potential for commercial application.

High power high repetition rate diode side-pumped Q-switched Nd:YAG rod laser

NASA Astrophysics Data System (ADS)

Lebiush, E.; Lavi, R.; Tzuk, Y.; Jackel, S.; Lallouz, R.; Tsadka, S.

1998-01-01

A Q-switched diode side-pumped Nd:YAG rod laser is presented. The design is based on close coupled diodes which are mounted side by side to a laser rod cut at Brewster angle. No intra-cavity optics are needed to compensate for the induced thermal lensing of the rod. This laser produces 10 W average power with 30 ns pulse width and beam quality of 1.3 times diffraction limited at 10 kHz repetition rate. The light to light conversion efficiency is 12%. The same average power and beam quality is kept while operating the laser at repetition rates up to 50 kHz.

40 CFR 80.305 - How are credits generated during the time period 2000 through 2003?

Code of Federal Regulations, 2011 CFR

2011-07-01

... AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Abt... averaging period. Va = Total volume of gasoline produced during the averaging period at the refinery (or for a foreign refinery, the total volume of gasoline produced during the averaging period at the...

40 CFR 80.305 - How are credits generated during the time period 2000 through 2003?

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur Abt... averaging period. Va = Total volume of gasoline produced during the averaging period at the refinery (or for a foreign refinery, the total volume of gasoline produced during the averaging period at the...

Production of no-carrier-added 64Cu from zinc metal irradiated under boron shielding.

PubMed

Zinn, K R; Chaudhuri, T R; Cheng, T P; Morris, J S; Meyer, W A

1994-02-01

Positron emission tomography offers advantages for radioimmunodiagnosis of cancer but requires radionuclides of appropriate half-life that have high specific activity and high radio-purity. This work was designed to develop a viable method to produce and purify 64Cu, which has high specific activity, for positron emission tomography. 64Cu was produced at the University of Missouri Research Reactor by the nuclear reaction, 64Zn(n,p)64Cu. Highly pure zinc metal (99.9999%) was irradiated in a specially designed boron nitrite lined container, which minimized thermal neutron reactions during irradiation. A new two-step procedure was developed to chemically separate the no-carrier-added 64Cu from the zinc metal target. 64Cu recovery for 24 runs averaged 0.393 (+/- 0.007) mCi per milligram of zinc irradiated. The boron-lined irradiation container reduced unwanted zinc radionuclides 14.3-fold. Zinc radionuclides and non-radioactive zinc were separated successfully from the 64Cu. The new separation technique was fast (2 hours total time) and highly efficient for removing the zinc. The zinc separation factor for this technique averaged 8.5 x 10(-8), indicating less than 0.0000085% of the zinc remained after separation. Thus far, the highest 64Cu specific activity at end of irradiation was 683 Ci/mg Cu, with an average of 512 Ci/mg Cu for the last six analyzed runs. The boron-lined irradiation container has sufficient capacity for 75-fold larger-sized zinc targets (up to 45 g). The new separation technique was excellent for separating 64Cu, which appears to be a radionuclide with great potential for positron emission tomography.

Coherent beam combiner for a high power laser

DOEpatents

Dane, C. Brent; Hackel, Lloyd A.

2002-01-01

A phase conjugate laser mirror employing Brillouin-enhanced four wave mixing allows multiple independent laser apertures to be phase locked producing an array of diffraction-limited beams with no piston phase errors. The beam combiner has application in laser and optical systems requiring high average power, high pulse energy, and low beam divergence. A broad range of applications exist in laser systems for industrial processing, especially in the field of metal surface treatment and laser shot peening.

Effects of meridional flow variations on solar cycles 23 and 24

DOE Office of Scientific and Technical Information (OSTI.GOV)

Upton, Lisa; Hathaway, David H., E-mail: lisa.a.upton@vanderbilt.edu, E-mail: lar0009@uah.edu, E-mail: david.hathaway@nasa.gov

2014-09-10

The faster meridional flow that preceded the solar cycle 23/24 minimum is thought to have led to weaker polar field strengths, producing the extended solar minimum and the unusually weak cycle 24. To determine the impact of meridional flow variations on the sunspot cycle, we have simulated the Sun's surface magnetic field evolution with our newly developed surface flux transport model. We investigate three different cases: a constant average meridional flow, the observed time-varying meridional flow, and a time-varying meridional flow in which the observed variations from the average have been doubled. Comparison of these simulations shows that the variationsmore » in the meridional flow over cycle 23 have a significant impact (∼20%) on the polar fields. However, the variations produced polar fields that were stronger than they would have been otherwise. We propose that the primary cause of the extended cycle 23/24 minimum and weak cycle 24 was the weakness of cycle 23 itself—with fewer sunspots, there was insufficient flux to build a big cycle. We also find that any polar counter-cells in the meridional flow (equatorward flow at high latitudes) produce flux concentrations at mid-to-high latitudes that are not consistent with observations.« less

A process for the chemical preparation of high-field ZnO varistors

DOEpatents

Brooks, R.A.; Dosch, R.G.; Tuttle, B.A.

1986-02-19

Chemical preparation techniques involving co-precipitation of metals are used to provide microstructural characteristics necessary in order to produce ZnO varistors and their precursors for high field applications. The varistors produced have homogeneous and/or uniform dopant distributions and a submicron average grain size with a narrow size distribution. Precursor powders are prepared via chemical precipitation techniques and varistors made by sintering uniaxially and/or isostatically pressed pellets. Using these methods, varistors were made which were suitable for high-power applications, having values of breakdown field, E/sub B/, in the 10 to 100 kV/cm range, ..cap alpha.. > 30 and densities in the range of 65 to 99% of theoretical, depending on both composition and sintering temperature.

Process for the chemical preparation of high-field ZnO varistors

DOEpatents

Brooks, Robert A.; Dosch, Robert G.; Tuttle, Bruce A.

1987-01-01

Chemical preparation techniques involving co-precipitation of metals are used to provide micro-structural characteristics necessary in order to produce ZnO varistors and their precursors for high field applications. The varistors produced have homogeneous and/or uniform dopant distributions and a submicron average grain size with a narrow size distribution. Precursor powders are prepared via chemical precipitation techniques and varistors made by sintering uniaxially and/or isostatically pressed pellets. Using these methods, varistors were made which were suitable for high-power applications, having values of breakdown field, E.sub.B, in the 10-100 kV/cm range, .alpha.>30 and densities in the range of 65-99% of theoretical, depending on both composition and sintering temperature.

Development of a high efficiency thin silicon solar cell

NASA Technical Reports Server (NTRS)

Storti, G.; Culik, J.; Wrigley, C.

1980-01-01

Significant improvements in open-circuit voltage and conversion efficiency, even on relatively high bulk resistivity silicon, were achieved by using a screen-printed aluminum paste back surface field. A 4 sq cm 50 micron m thick cell was fabricated from textured 10 omega-cm silicon which had an open-circuit voltage of 595 mV and AMO conversion efficiency at 25 C of 14.3%. The best 4 sq cm 50 micron thick cell (2 omega-cm silicon) produced had an open-circuit voltage of 607 mV and an AMO conversion efficiency of 15%. Processing modifications are described which resulted in better front contact integrity and reduced breakage. These modifications were utilized in the thin cell pilot line to fabricate 4 sq cm cells with an average AMO conversion efficiency at 25 C of better than 12.5% and with lot yields as great as 51% of starts; a production rate of 10,000 cells per month was demonstrated. A pilot line was operated which produced large area (25 cm) ultra-thin cells with an average AMO conversion efficiency at 25 deg of better than 11.5% and a lot yield as high as 17%.

High field gradient particle accelerator

DOEpatents

Nation, John A.; Greenwald, Shlomo

1989-01-01

A high electric field gradient electron accelerator utilizing short duration, microwave radiation, and capable of operating at high field gradients for high energy physics applications or at reduced electric field gradients for high average current intermediate energy accelerator applications. Particles are accelerated in a smooth bore, periodic undulating waveguide, wherein the period is so selected that the particles slip an integral number of cycles of the r.f. wave every period of the structure. This phase step of the particles produces substantially continuous acceleration in a traveling wave without transverse magnetic or other guide means for the particle.

Jitter compensation circuit

DOEpatents

Sullivan, James S.; Ball, Don G.

1997-01-01

The instantaneous V.sub.co signal on a charging capacitor is sampled and the charge voltage on capacitor C.sub.o is captured just prior to its discharge into the first stage of magnetic modulator. The captured signal is applied to an averaging circuit with a long time constant and to the positive input terminal of a differential amplifier. The averaged V.sub. co signal is split between a gain stage (G=0.975) and a feedback stage that determines the slope of the voltage ramp applied to the high speed comparator. The 97.5% portion of the averaged V.sub.co signal is applied to the negative input of a differential amplifier gain stage (G=10). The differential amplifier produces an error signal by subtracting 97.5% of the averaged V.sub.co signal from the instantaneous value of sampled V.sub.co signal and multiplying the difference by ten. The resulting error signal is applied to the positive input of a high speed comparator. The error signal is then compared to a voltage ramp that is proportional to the averaged V.sub.co values squared divided by the total volt-second product of the magnetic compression circuit.

Jitter compensation circuit

DOEpatents

Sullivan, J.S.; Ball, D.G.

1997-09-09

The instantaneous V{sub co} signal on a charging capacitor is sampled and the charge voltage on capacitor C{sub o} is captured just prior to its discharge into the first stage of magnetic modulator. The captured signal is applied to an averaging circuit with a long time constant and to the positive input terminal of a differential amplifier. The averaged V{sub co} signal is split between a gain stage (G = 0.975) and a feedback stage that determines the slope of the voltage ramp applied to the high speed comparator. The 97.5% portion of the averaged V{sub co} signal is applied to the negative input of a differential amplifier gain stage (G = 10). The differential amplifier produces an error signal by subtracting 97.5% of the averaged V{sub co} signal from the instantaneous value of sampled V{sub co} signal and multiplying the difference by ten. The resulting error signal is applied to the positive input of a high speed comparator. The error signal is then compared to a voltage ramp that is proportional to the averaged V{sub co} values squared divided by the total volt-second product of the magnetic compression circuit. 11 figs.

Half-Watt average power femtosecond source spanning 3-8 µm based on subharmonic generation in GaAs

NASA Astrophysics Data System (ADS)

Smolski, Viktor; Vasilyev, Sergey; Moskalev, Igor; Mirov, Mike; Ru, Qitian; Muraviev, Andrey; Schunemann, Peter; Mirov, Sergey; Gapontsev, Valentin; Vodopyanov, Konstantin

2018-06-01

Frequency combs with a wide instantaneous spectral span covering the 3-20 µm molecular fingerprint region are highly desirable for broadband and high-resolution frequency comb spectroscopy, trace molecular detection, and remote sensing. We demonstrate a novel approach for generating high-average-power middle-infrared (MIR) output suitable for producing frequency combs with an instantaneous spectral coverage close to 1.5 octaves. Our method is based on utilizing a highly-efficient and compact Kerr-lens mode-locked Cr2+:ZnS laser operating at 2.35-µm central wavelength with 6-W average power, 77-fs pulse duration, and high 0.9-GHz repetition rate; to pump a degenerate (subharmonic) optical parametric oscillator (OPO) based on a quasi-phase-matched GaAs crystal. Such subharmonic OPO is a nearly ideal frequency converter capable of extending the benefits of frequency combs based on well-established mode-locked pump lasers to the MIR region through rigorous, phase- and frequency-locked down conversion. We report a 0.5-W output in the form of an ultra-broadband spectrum spanning 3-8 µm measured at 50-dB level.

Creation of high-pinning microstructures in post production YBCO coated conductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Welp, Ulrich; Miller, Dean J.; Kwok, Wai-Kwong

A method comprising irradiating a polycrystalline rare earth metal-alkaline earth metal-transition metal-oxide superconductor layer with protons having an energy of 1 to 6 MeV. The irradiating process produces an irradiated layer that comprises randomly dispersed defects with an average diameter in the range of 1-10 nm.

South Belridge fields, Borderland basin, U. S. , San Joaquin Valley

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, D.D.; McPherson, J.G.

1991-03-01

South Belridge is a giant field in the west San Joaquin Valley, Kern County. Cumulative field production is approximately 700 MMBO and 220 BCFG, with remaining recoverable reserves of approximately 500 MMBO. The daily production is nearly 180 MBO from over 6100 active wells. The focus of current field development and production is the shallow Tulare reservoir. Additional probable diatomite reserves have been conservatively estimated at 550 MMBO and 550 BCFG. South Belridge field has two principal reservoir horizons; the Mio-Pliocene Belridge diatomite of the upper Monterey Formation, and the overlying Plio-Pleistocene Tulare Formation. The field lies on the crestmore » of a large southeast-plunging anticline, sub-parallel to the nearby San Andreas fault system. The reservoir trap in both the Tulare and diatomite reservoir horizons is a combination of structure, stratigraphic factors, and tar seals; the presumed source for the oil is the deeper Monterey Formation. The diatomite reservoir produces light oil (20-32{degree} API gravity) form deep-marine diatomite and diatomaceous shales with extremely high porosity (average 60%) and low permeability (average 1 md). In contrast, the shallow ({lt}1000 ft (305 m) deep) overlying Tulare reservoir produces heavy oil (13-14{degree} API gravity) from unconsolidated, arkosic, fluviodeltaic sands of high porosity (average 35%) and permeability (average 3000 md). The depositional model is that of a generally prograding fluviodeltaic system sourced in the nearby basin-margin highlands. More than 6000 closely spaced, shallow wells are the key to steamflood production from hundreds of layered and laterally discontinuous reservoir sands which create laterally and vertically discontinuous reservoir flow units.« less

Ovum pick up, in vitro embryo production, and pregnancy rates from a large-scale commercial program using Nelore cattle (Bos indicus) donors.

PubMed

Pontes, J H F; Melo Sterza, F A; Basso, A C; Ferreira, C R; Sanches, B V; Rubin, K C P; Seneda, M M

2011-06-01

The objective was to clarify in vitro production of bovine embryos in Brazil. Data from 656 ovum pick-up/in vitro production (OPU/IVP) procedures, performed on 317 Nelore (Bos indicus) donors, without hormone stimulation or control of ovarian follicular waves, were analysed. Donors were subjected to OPU from one to nine times (no specific schedule), with < 15 d between consecutive procedures. There were 20,848 oocytes, of which 15,747 (75.53%) were considered viable, 5,446 embryos were obtained, 5,398 embryos were immediately transferred, resulting in 1,974 pregnancies (36.57%) at Day 30 and 1,788 (33.12%) pregnancies at Day 60. The average number of total and viable oocytes produced per OPU session was (mean ± SEM) 30.84 ± 0.88 and 23.35 ± 0.7 (average of 8.1 ± 0.3 embryos and 3.0 ± 0.1 pregnancies per OPU-IVP procedure). Since oocyte production varied widely among donor, they were designated as very high, high, intermediate, and low, with 58.94 ± 2.04, 32.61 ± 0.50, 22.13 ± 0.50, and 10.26 ± 0.57 oocytes, respectively, produced by 78, 80, 79, and 80 donors. The number of viable oocytes recovered ranged from 0 to 128; since donors with numerous viable oocytes produced many viable embryos and pregnancies, oocyte production was useful for donor selection. However, there was no significant effect of the number of OPU sessions per donor on mean numbers of oocytes produced. In conclusion, we confirmed field reports of high oocyte production by some Nelore donors and demonstrated individual variation in oocyte yield, which was associated with embryo production and pregnancy rates. Copyright © 2011 Elsevier Inc. All rights reserved.

High-average-power 2-kHz laser for generation of ultrashort x-ray pulses.

PubMed

Jiang, Yan; Lee, Taewoo; Li, Wei; Ketwaroo, Gyanprakash; Rose-Petruck, Christoph G

2002-06-01

We describe a Ti:sapphire-based laser-x-ray system specifically designed for generation of ultrafast x-ray pulses in the tenths-of-nanometers spectral range at a 2-kHz repetition rate. To obtain high-contrast laser pulses we divide the laser system into a section for generation of microjoule, high-contrast pulses with pulse cleaning and a subsequent section for chirped-pulse amplification and pulse compression. This laser section operates in conjunction with an x-ray-generation section based on a moving copper wire in a He atmosphere. The high reliability of the entire system permits maintenance-free production of x-ray pulses over tens of hours. Average x-ray fluxes of 10(13) photons/(s 4pi sr 1 keV) at 3 keV and 10(9) photons/(s 4pi sr) above 5 keV of photon energy are produced.

Historical instrumental climate data for Australia - quality and utility for palaeoclimatic studies

NASA Astrophysics Data System (ADS)

Nicholls, Neville; Collins, Dean; Trewin, Blair; Hope, Pandora

2006-10-01

The quality and availability of climate data suitable for palaeoclimatic calibration and verification for the Australian region are discussed and documented. Details of the various datasets, including problems with the data, are presented. High-quality datasets, where such problems are reduced or even eliminated, are discussed. Many climate datasets are now analysed onto grids, facilitating the preparation of regional-average time series. Work is under way to produce such high-quality, gridded datasets for a variety of hitherto unavailable climate data, including surface humidity, pan evaporation, wind, and cloud. An experiment suggests that only a relatively small number of palaeoclimatic time series could provide a useful estimate of long-term changes in Australian annual average temperature. Copyright

Diode-side-pumped intracavity frequency-doubled Nd:YAG/BaWO4 Raman laser generating average output power of 3.14 W at 590 nm.

PubMed

Li, Shutao; Zhang, Xingyu; Wang, Qingpu; Zhang, Xiaolei; Cong, Zhenhua; Zhang, Huaijin; Wang, Jiyang

2007-10-15

We report a linear-cavity high-power all-solid-state Q-switched yellow laser. The laser source comprises a diode-side-pumped Nd:YAG module that produces 1064 nm fundamental radiation, an intracavity BaWO(4) Raman crystal that generates a first-Stokes laser at 1180 nm, and a KTP crystal that frequency doubles the first-Stokes laser to 590 nm. A convex-plane cavity is employed in this configuration to counteract some of the thermal effect caused by high pump power. An average output power of 3.14 W at 590 nm is obtained at a pulse repetition frequency of 10 kHz.

Electron Source based on Superconducting RF

NASA Astrophysics Data System (ADS)

Xin, Tianmu

High-bunch-charge photoemission electron-sources operating in a Continuous Wave (CW) mode can provide high peak current as well as the high average current which are required for many advanced applications of accelerators facilities, for example, electron coolers for hadron beams, electron-ion colliders, and Free-Electron Lasers (FELs). Superconducting Radio Frequency (SRF) has many advantages over other electron-injector technologies, especially when it is working in CW mode as it offers higher repetition rate. An 112 MHz SRF electron photo-injector (gun) was developed at Brookhaven National Laboratory (BNL) to produce high-brightness and high-bunch-charge bunches for electron cooling experiments. The gun utilizes a Quarter-Wave Resonator (QWR) geometry for a compact structure and improved electron beam dynamics. The detailed RF design of the cavity, fundamental coupler and cathode stalk are presented in this work. A GPU accelerated code was written to improve the speed of simulation of multipacting, an important hurdle the SRF structure has to overcome in various locations. The injector utilizes high Quantum Efficiency (QE) multi-alkali photocathodes (K2CsSb) for generating electrons. The cathode fabrication system and procedure are also included in the thesis. Beam dynamic simulation of the injector was done with the code ASTRA. To find the optimized parameters of the cavities and beam optics, the author wrote a genetic algorithm Python script to search for the best solution in this high-dimensional parameter space. The gun was successfully commissioned and produced world record bunch charge and average current in an SRF photo-injector.

Recent Developments in the Analysis of Couple Oscillator Arrays

NASA Technical Reports Server (NTRS)

Pogorzelski, Ronald J.

2000-01-01

This presentation considers linear arrays of coupled oscillators. Our purpose in coupling oscillators together is to achieve high radiated power through the spatial power combining which results when the oscillators are injection locked to each other. York, et. al. have shown that, left to themselves, the ensemble of injection locked oscillators oscillate at the average of the tuning frequencies of all the oscillators. Coupling these arrays achieves high radiated power through coherent spatial power combining. The coupled oscillators are usually designed to produce constant aperture phase. Oscillators are injection locked to each other or to a master oscillator to produce coherent radiation. Oscillators do not necessarily oscillate at their tuning frequency.

Generation of flat-top pulsed magnetic fields with feedback control approach.

PubMed

Kohama, Yoshimitsu; Kindo, Koichi

2015-10-01

We describe the construction of a simple, compact, and cost-effective feedback system that produces flat-top field profiles in pulsed magnetic fields. This system is designed for use in conjunction with a typical capacitor-bank driven pulsed magnet and was tested using a 60-T pulsed magnet. With the developed feedback controller, we have demonstrated flat-top magnetic fields as high as 60.64 T with an excellent field stability of ±0.005 T. The result indicates that the flat-top pulsed magnetic field produced features high field stability and an accessible field strength. These features make this system useful for improving the resolution of data with signal averaging.

Intermediate photovoltaic system application experiment operational performance report: Volume 5, for Beverly High School, Beverly, Mass.

NASA Astrophysics Data System (ADS)

1982-02-01

Performance data for the month of January, 1982 for a grid connected photovoltaic power supply in Massachusetts are presented. Data include: monthly and daily electrical energy produced; monthly and daily solar energy incident on the array; monthly and daily array efficiency; plots of energy produced as a function of power level, voltage, cell temperature and time of day; power conditioner input, output and efficiency for each of two individual units and for the total power conditioning system; photovoltaic system efficiency; capacity factor; PV system to load and grid to load energies and corresponding dollar values; daily energy supplies to the load by the PV system; daily PV system availability; monthly and hourly insolation; monthly and hourly temperature average; monthly and hourly wind speed; wind direction distribution; average heating and cooling degree days; number of freeze/thaw cycles; and the data acquisition mode and recording interval plot.

Chemical synthesis and structural characterization of small AuZn nanoparticles

NASA Astrophysics Data System (ADS)

Juárez-Ruiz, E.; Pal, U.; Lombardero-Chartuni, J. A.; Medina, A.; Ascencio, J. A.

2007-03-01

In this paper, we report the aqueous synthesis of bimetallic Au-Zn nanoparticles of different compositions by the simultaneous reduction technique. The stability and atomic configuration of the particles are studied through high-resolution transmission electron microscopy (HRTEM) and UV-Vis optical absorption techniques. Depending on the composition, small bimetallic nanoparticles of 1 15 nm in size were obtained. The average size and size distribution of the bimetallic nanoparticles are seen to be critically dependent on the atomic ratio of the constituting elements Au and Zn. While a 1:1 atomic proportion of Au and Zn produced most stable nanoparticles of smallest average size, nanoparticles produced with higher content of either of the component elements are unstable, inducing agglomeration and coalescence to form elongated structures with uneven morphologies. Au3Zn1 nanoparticles followed a directional growth pattern, producing bimetallic nanorods with multiple crystalline domains. Interestingly, in these rod-like nanostructures, the domains are in well array of solid solution-like bimetallic and pure mono-metallic regions alternatively. Such nanostructures with uneven morphology and compositions might show distinct catalytic selectivity in chemical reactions.

Epoch length to accurately estimate the amplitude of interference EMG is likely the result of unavoidable amplitude cancellation

PubMed Central

Keenan, Kevin G.; Valero-Cuevas, Francisco J.

2008-01-01

Researchers and clinicians routinely rely on interference electromyograms (EMGs) to estimate muscle forces and command signals in the neuromuscular system (e.g., amplitude, timing, and frequency content). The amplitude cancellation intrinsic to interference EMG, however, raises important questions about how to optimize these estimates. For example, what should the length of the epoch (time window) be to average an EMG signal to reliably estimate muscle forces and command signals? Shorter epochs are most practical, and significant reductions in epoch have been reported with high-pass filtering and whitening. Given that this processing attenuates power at frequencies of interest (< 250 Hz), however, it is unclear how it improves the extraction of physiologically-relevant information. We examined the influence of amplitude cancellation and high-pass filtering on the epoch necessary to accurately estimate the “true” average EMG amplitude calculated from a 28 s EMG trace (EMGref) during simulated constant isometric conditions. Monte Carlo iterations of a motor-unit model simulating 28 s of surface EMG produced 245 simulations under 2 conditions: with and without amplitude cancellation. For each simulation, we calculated the epoch necessary to generate average full-wave rectified EMG amplitudes that settled within 5% of EMGref. For the no-cancellation EMG, the necessary epochs were short (e.g., < 100 ms). For the more realistic interference EMG (i.e., cancellation condition), epochs shortened dramatically after using high-pass filter cutoffs above 250 Hz, producing epochs short enough to be practical (i.e., < 500 ms). We conclude that the need to use long epochs to accurately estimate EMG amplitude is likely the result of unavoidable amplitude cancellation, which helps to clarify why high-pass filtering (> 250 Hz) improves EMG estimates. PMID:19081815

Ultrashort pulse laser deposition of thin films

DOEpatents

Perry, Michael D.; Banks, Paul S.; Stuart, Brent C.

2002-01-01

Short pulse PLD is a viable technique of producing high quality films with properties very close to that of crystalline diamond. The plasma generated using femtosecond lasers is composed of single atom ions with no clusters producing films with high Sp.sup.3 /Sp.sup.2 ratios. Using a high average power femtosecond laser system, the present invention dramatically increases deposition rates to up to 25 .mu.m/hr (which exceeds many CVD processes) while growing particulate-free films. In the present invention, deposition rates is a function of laser wavelength, laser fluence, laser spot size, and target/substrate separation. The relevant laser parameters are shown to ensure particulate-free growth, and characterizations of the films grown are made using several diagnostic techniques including electron energy loss spectroscopy (EELS) and Raman spectroscopy.

Study of the effect of electromagnetic fields on indoor and outdoor radon concentrations

NASA Astrophysics Data System (ADS)

Haider, Lina M.; Shareef, N. R.; Darwoysh, H. H.; Mansour, H. L.

2018-05-01

In the present work, the effect of electromagnetic fields produced by high voltage power lines(132kV) and indoor equipments on the indoor and outdoor average radon concentrations in Al-Kazaliya and Hay Al-Adil regions in Baghdad city were studied using CR-39 track detectors and a gauss-meter.Results of measurements of the present study, have shown that the highest value for the indoor average radon concentration (76.56± 8.44 Bq / m3) was recorded for sample A1(Hay Al-Adel) at a distance of (20 m) from the high voltage power lines, while the lowest value for the indoor average radon concentration (30.46 ± 8.44 Bq / m3) was recorded for sample A3 (Hay Al-Adil) at a distance of (50 m) from the high voltage power lines. The indoor gaussmeter measurements were found to be ranged from (30.2 mG) to (38.5 mG). The higest value for outdoor average radon concentration and the highest gaussmeter measurements were found for sample (1), with values (92.63 ±11.2 Bq / m3) and (87.24 ± 2.85 mG), directly under the high voltage power lines respectively, while the lowest outdoor average radon concentration and the lowest gaussmeter measurements were found in sample (4),with values (34.19 ± 6.33 Bq / m3) and (1.16 ± 0.14 Bq / m3),), at a distance of (120 m) from the high voltage power lines respectively. The results of the present work have shown that there might be an influence of the electromagnetic field on radon concentrations in areas which were close to high voltage power lines and houses which have used many electric equipment for a long period of time.

Natural Contamination with Mycotoxins Produced by Fusarium graminearum and Fusarium poae in Malting Barley in Argentina

PubMed Central

Nogueira, María Soledad; Decundo, Julieta; Martinez, Mauro; Dieguez, Susana Nelly; Moreyra, Federico; Moreno, Maria Virginia

2018-01-01

Two of the most common species of toxin-producing Fusarium contaminating small cereal grains are Fusarium graminearum and F. poae; with both elaborating diverse toxins, especially deoxynivalenol (DON) and nivalenol (NIV), respectively. The objective of our work during the 2012–2014 growing seasons was to screen crops for the most commonly isolated Fusarium species and to quantify DON and NIV toxins in natural malting-barley samples from different producing areas of Argentina. We identified 1180 Fusarium isolates in the 119 samples analyzed, with 51.2% being F. graminearum, 26.2% F. poae and 22.6% other species. We found high concentrations of mycotoxins, at maximum values of 12 μg/g of DON and 7.71 μg/g of NIV. Of the samples, 23% exhibited DON at an average of 2.36 μg/g, with 44% exceeding the maximum limits (average of 5.24 μg/g); 29% contained NIV at an average of 2.36 μg/g; 7% contained both DON and NIV; and 55% were without DON or NIV. Finally, we report the mycotoxin contamination of the grain samples produced by F. graminearum and F. poae, those being the most frequent Fusarium species present. We identified the main Fusarium species affecting natural malting-barley grains in Argentina and documented the presence of many samples with elevated concentrations of DON and NIV. To our knowledge, the investigation reported here was the first to quantify the contamination by Fusarium and its toxins in natural samples of malting barley in Argentina. PMID:29439459

Natural Contamination with Mycotoxins Produced by Fusarium graminearum and Fusarium poae in Malting Barley in Argentina.

PubMed

Nogueira, María Soledad; Decundo, Julieta; Martinez, Mauro; Dieguez, Susana Nelly; Moreyra, Federico; Moreno, Maria Virginia; Stenglein, Sebastian Alberto

2018-02-11

Two of the most common species of toxin-producing Fusarium contaminating small cereal grains are Fusarium graminearum and F. poae ; with both elaborating diverse toxins, especially deoxynivalenol (DON) and nivalenol (NIV), respectively. The objective of our work during the 2012-2014 growing seasons was to screen crops for the most commonly isolated Fusarium species and to quantify DON and NIV toxins in natural malting-barley samples from different producing areas of Argentina. We identified 1180 Fusarium isolates in the 119 samples analyzed, with 51.2% being F. graminearum , 26.2% F. poae and 22.6% other species. We found high concentrations of mycotoxins, at maximum values of 12 μg/g of DON and 7.71 μg/g of NIV. Of the samples, 23% exhibited DON at an average of 2.36 μg/g, with 44% exceeding the maximum limits (average of 5.24 μg/g); 29% contained NIV at an average of 2.36 μg/g; 7% contained both DON and NIV; and 55% were without DON or NIV. Finally, we report the mycotoxin contamination of the grain samples produced by F. graminearum and F. poae , those being the most frequent Fusarium species present. We identified the main Fusarium species affecting natural malting-barley grains in Argentina and documented the presence of many samples with elevated concentrations of DON and NIV. To our knowledge, the investigation reported here was the first to quantify the contamination by Fusarium and its toxins in natural samples of malting barley in Argentina.

40 CFR 421.306 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... average mg/kg (pounds per million pounds) of TiCl4 produced Chromium (total) 0.346 0.140 Lead 0.262 0.122... Maximum for monthly average mg/kg (pounds per million pounds) of TiCl4 produced Chromium (total) 0.385 0... for any 1 day Maximum for monthly average mg/kg (pounds per million pounds) of TiCl4 handled Chromium...

40 CFR 421.306 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... average mg/kg (pounds per million pounds) of TiCl4 produced Chromium (total) 0.346 0.140 Lead 0.262 0.122... Maximum for monthly average mg/kg (pounds per million pounds) of TiCl4 produced Chromium (total) 0.385 0... for any 1 day Maximum for monthly average mg/kg (pounds per million pounds) of TiCl4 handled Chromium...

40 CFR 421.306 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... average mg/kg (pounds per million pounds) of TiCl4 produced Chromium (total) 0.346 0.140 Lead 0.262 0.122... Maximum for monthly average mg/kg (pounds per million pounds) of TiCl4 produced Chromium (total) 0.385 0... for any 1 day Maximum for monthly average mg/kg (pounds per million pounds) of TiCl4 handled Chromium...

Relationship between equol producer status and metabolic parameters in 743 Japanese women: equol producer status is associated with antiatherosclerotic conditions in women around menopause and early postmenopause.

PubMed

Yoshikata, Remi; Myint, Khin Z; Ohta, Hiroaki

2017-02-01

Equol, an active metabolite possessing estrogen-like activity, is produced by the action of intestinal flora on soy isoflavones. There is an increasing evidence regarding its efficacy in the relief of menopausal symptoms, suppression of decreased bone mineral density, and lipid profile improvement. Only those with equol-producing capacity, however, seem to benefit. Thus, we examined the relationship between equol producer status and parameters associated with lifestyle-related diseases in women from their 20s to 80s. This cross-sectional study was conducted among 743 women (21-89 y; average age: 52.5 ± 11.8 y) who have undergone health screening at Tokyo Midtown Medical Center and given consent to participate in the study. The relationship between equol producer status and metabolic parameters was assessed. In our study, 236 women (32%) were equol producers. Equol producers had significantly lower triglycerides and higher high-density lipoprotein cholesterol levels compared with nonproducers. Equol-producing women in their 50s showed significantly lower body fat level, visceral fat area, triglyceride levels, pulse wave velocity, uric acid levels, and high sensitivity C-reactive protein levels. In addition, women in their 60s showed significantly higher levels of high-density lipoprotein cholesterol. In multivariate logistic regression, for women in their 50s, equol production was significantly associated with lower arterial stiffness and uric acid levels, and a high ratio of eicosapentaenoic acid to arachidonic acid, whereas it was significantly associated with lower urinary N-telopeptides in their 60s. Equol producer status was associated with favorable metabolic parameters, in women in the early phase postmenopause, with the transitional periods noted with declining intrinsic estrogen levels.

High-throughput machining using high average power ultrashort pulse lasers and ultrafast polygon scanner

NASA Astrophysics Data System (ADS)

Schille, Joerg; Schneider, Lutz; Streek, André; Kloetzer, Sascha; Loeschner, Udo

2016-03-01

In this paper, high-throughput ultrashort pulse laser machining is investigated on various industrial grade metals (Aluminium, Copper, Stainless steel) and Al2O3 ceramic at unprecedented processing speeds. This is achieved by using a high pulse repetition frequency picosecond laser with maximum average output power of 270 W in conjunction with a unique, in-house developed two-axis polygon scanner. Initially, different concepts of polygon scanners are engineered and tested to find out the optimal architecture for ultrafast and precision laser beam scanning. Remarkable 1,000 m/s scan speed is achieved on the substrate, and thanks to the resulting low pulse overlap, thermal accumulation and plasma absorption effects are avoided at up to 20 MHz pulse repetition frequencies. In order to identify optimum processing conditions for efficient high-average power laser machining, the depths of cavities produced under varied parameter settings are analyzed and, from the results obtained, the characteristic removal values are specified. The maximum removal rate is achieved as high as 27.8 mm3/min for Aluminium, 21.4 mm3/min for Copper, 15.3 mm3/min for Stainless steel and 129.1 mm3/min for Al2O3 when full available laser power is irradiated at optimum pulse repetition frequency.

Production and properties of electrosprayed sericin nanopowder

NASA Astrophysics Data System (ADS)

Hazeri, Najmeh; Tavanai, Hossein; Moradi, Ali Reza

2012-06-01

Sericin is a proteinous substrate that envelops fibroin (silk) fiber, and its recovery provides significant economical and social benefits. Sericin is an antibacterial agent that resists oxidation and absorbs moisture and UV light. In powder form, sericin has a wide range of applications in food, cosmetics and drug delivery. Asides from other techniques of producing powder, such as precipitation and spray drying, electrospraying can yield solid nanoparticles, particularly in the submicron range. Here, we report the production of sericin nanopowder by electrospraying. Sericin sponge was recovered from Bombyx mori cocoons through a high-temperature, high-pressure process, followed by centrifugation and freeze drying of the sericin solution. The electrospraying solution was prepared by dissolving the sericin sponge in dimethyl sulfoxide. We demonstrate that electrospraying is capable of producing sericin nanopowder with an average particle size of 25 nm, which is by far smaller than the particles produced by other techniques. The electrosprayed sericin nanopowder consists of small crystallites and exhibits a high moisture absorbance.

Love the Lab, Hate the Lab Report?

ERIC Educational Resources Information Center

Bjorn, Genevive

2018-01-01

In the author's large, urban high school, enrollment in a laboratory science is mandatory. While the student participation rate for lab activities is over 98%, the turn-in rate for traditional lab reports averages just 35% to 85%. Those students who don't produce a lab report miss a critical opportunity to improve their skills in scientific…

Tear Down and Inspection of the Cummins VTA-903 Evaluated Using the Single Common Powertrain Lubricant SCPL

DTIC Science & Technology

2013-12-13

Materials AT Anti-Thrust AVG Average BFV Bradley Fighting Vehicle CAT Caterpillar EOT End Of Test GEP General Engine Products HMMWV High...Vehicle ( BFV ), is a 14.8 liter, V8, turbocharged after-cooled diesel engine, producing approximately 600 hp, and 1225 lb-ft of torque at their respective

Outstanding adsorption performance of high aspect ratio and super-hydrophobic carbon nanotubes for oil removal.

PubMed

Kayvani Fard, Ahmad; Mckay, Gordon; Manawi, Yehia; Malaibari, Zuhair; Hussien, Muataz A

2016-12-01

Oil removal from water is a highly important area due to the large production rate of emulsified oil in water, which is considered one of the major pollutants, having a negative effect on human health, environment and wildlife. In this study, we have reported the application of high quality carbon nanotube bundles produced by an injected vertical chemical vapor deposition (IV-CVD) reactor for oil removal. High quality, bundles, super hydrophobic, and high aspect ratio carbon nanotubes were produced. The average diameters of the produced CNTs ranged from 20 to 50 nm while their lengths ranged from 300 to 500 μm. Two types of CNTs namely, P-CNTs and C-CNTs, (Produced CNTs from the IV-CVD reactor and commercial CNTs) were used for oil removal from water. For the first time, thermogravimetric analysis (TGA) was conducted to measure maximum oil uptake using CNT and it was found that P-CNT can take oil up to 17 times their weight. The effect of adsorbent dosage, contact time, and agitation speed were examined on the oil spill clean-up efficiency using batch sorption experiments. Higher efficiency with almost 97% removal was achieved using P-CNTs compared to 87% removal using C-CNTs. Copyright © 2016 Elsevier Ltd. All rights reserved.

High Production of LukMF' in Staphylococcus aureus Field Strains Is Associated with Clinical Bovine Mastitis.

PubMed

Hoekstra, Jurriaan; Rutten, Victor; Sommeling, Laura; van Werven, Tine; Spaninks, Mirlin; Duim, Birgitta; Benedictus, Lindert; Koop, Gerrit

2018-05-15

Staphylococcus aureus , a major cause of bovine mastitis, produces a wide range of immune-evasion molecules. The bi-component leukocidin LukMF' is a potent killer of bovine neutrophils in vitro. Since the role of LukMF' in development of bovine mastitis has not been studied in natural infections, we aimed to clarify whether presence of the lukM-lukF' genes and production levels of LukMF' are associated with clinical severity of the disease. Staphylococcus aureus was isolated from mastitis milk samples (38 clinical and 17 subclinical cases) from 33 different farms. The lukM - lukF' genes were present in 96% of the isolates. Remarkably, 22% of the lukM-lukF' -positive S. aureus isolates displayed a 10-fold higher in vitro LukMF' production than the average of the lower-producing ones. These high producing isolates were cultured significantly more frequently from clinical than subclinical mastitis cases. Also, the detection of LukM protein in milk samples was significantly associated with clinical mastitis and high production in vitro. The high producing LukMF' strains all belonged to the same genetic lineage, spa -type t543. Analysis of their global toxin gene regulators revealed a point mutation in the Repressor of toxins ( rot ) gene which results in a non-functional start codon, preventing translation of rot . This mutation was only identified in high LukMF' producing isolates and not in low LukMF' producing isolates. Since rot suppresses the expression of various toxins including leukocidins, this mutation is a possible explanation for increased LukMF' production. Identification of high LukMF' producing strains is of clinical relevance and can potentially be used as a prognostic marker for severity of mastitis.

High field gradient particle accelerator

DOEpatents

Nation, J.A.; Greenwald, S.

1989-05-30

A high electric field gradient electron accelerator utilizing short duration, microwave radiation, and capable of operating at high field gradients for high energy physics applications or at reduced electric field gradients for high average current intermediate energy accelerator applications is disclosed. Particles are accelerated in a smooth bore, periodic undulating waveguide, wherein the period is so selected that the particles slip an integral number of cycles of the r.f. wave every period of the structure. This phase step of the particles produces substantially continuous acceleration in a traveling wave without transverse magnetic or other guide means for the particle. 10 figs.

Ion thruster performance model

NASA Technical Reports Server (NTRS)

Brophy, J. R.

1984-01-01

A model of ion thruster performance is developed for high flux density, cusped magnetic field thruster designs. This model is formulated in terms of the average energy required to produce an ion in the discharge chamber plasma and the fraction of these ions that are extracted to form the beam. The direct loss of high energy (primary) electrons from the plasma to the anode is shown to have a major effect on thruster performance. The model provides simple algebraic equations enabling one to calculate the beam ion energy cost, the average discharge chamber plasma ion energy cost, the primary electron density, the primary-to-Maxwellian electron density ratio and the Maxwellian electron temperature. Experiments indicate that the model correctly predicts the variation in plasma ion energy cost for changes in propellant gas (Ar, Kr and Xe), grid transparency to neutral atoms, beam extraction area, discharge voltage, and discharge chamber wall temperature. The model and experiments indicate that thruster performance may be described in terms of only four thruster configuration dependent parameters and two operating parameters. The model also suggests that improved performance should be exhibited by thruster designs which extract a large fraction of the ions produced in the discharge chamber, which have good primary electron and neutral atom containment and which operate at high propellant flow rates.

Sex-linked strategies of human reproductive behavior.

PubMed

Jaffe, K; Urribarri, D; Chacon, G C; Diaz, G; Torres, A; Herzog, G

1993-01-01

We present data on fertility characteristics in the Venezuelan population for each sex separately, allowing a detailed comparative analysis of the variance in fertility between males and females. We show that the fertility distribution for both sexes is discontinuous, that the average female has a larger number of offspring per individual than the average male, and that highly fertile males outnumber highly fertile females so that the total number of offspring produced by males and females is balanced. Results indicate that a few males are responsible for a relative higher fertility of the average female and that interactions between polyandric females with monogamic and polygynic males are common. Among the Yanomami, a relatively unacculturated hunter-gatherer-horticulturist tribe, similar differences in fertility distribution of both sexes are apparent. The data suggest that human populations contain statistically distinct subpopulations, with different reproductive strategies, suggesting the existence of complex interactions among human populations which are not evident from the study of individuals or groups.

Cloud Climatology for Land Stations Worldwide, 1971-2009 (NDP-026D)

DOE Data Explorer

Hahn, C. J. [University of Arizona; Warren, S. G. [University of Washington; Eastman, R. [University of Washington

2012-08-01

Surface synoptic weather reports for 39 years have been processed to provide a climatology of clouds for each of over 5000 land-based weather stations with long periods of record both day and night. For each station, this digital archive includes: multi-year annual, seasonal and monthly averages for day and night separately; seasonal and monthly averages by year; averages for eight times per day; and analyses of the first harmonic for the annual and diurnal cycles. Averages are given for total cloud cover, clear-sky frequency, and 9 cloud types: 5 in the low level (fog, St, Sc, Cu, Cb), 3 in the middle level (Ns, As, Ac) and one in the high level (all cirriform clouds combined). Cloud amounts and frequencies of occurrence are given for all types. In addition, non-overlapped amounts are given for middle and high cloud types, and average base heights are given for low cloud types. Nighttime averages were obtained by using only those reports that met an "illuminance criterion" (i.e., made under adequate moonlight or twilight), thus making possible the determination of diurnal cycles and nighttime trends for cloud types.The authors have also produced an online, gridded atlas of the cloud observations contained in NDP-026D. The Online Cloud Atlas containing NDP-026D data is available via the University of Washington.

Consistent, high-level ethanol consumption in pig-tailed macaques via a multiple-session, limited-intake, oral self-dosing procedure.

PubMed

Weed, Michael R; Wilcox, Kristin M; Ator, Nancy A; Hienz, Robert D

2008-06-01

Alcohol abuse is a major public health burden that can lead to many adverse health effects such as impaired hepatic, gastrointestinal, central nervous system and immune system function. Preclinical animal models of alcohol abuse allow for experimental control over variables often difficult to control in human clinical studies (e.g., ethanol exposure before or during the study, history of other drug use, access to medical care, nutritional status, etc). Nonhuman primate models in particular provide increased genetic, anatomic and physiologic similarity to humans, relative to rodent models. A small percentage of macaques will spontaneously consume large quantities of ethanol; however, most nonhuman primate models of "voluntary" ethanol intake produce relatively low daily ethanol intake in the majority of monkeys. To facilitate study of chronic exposure to high levels of ethanol intake, a macaque model has been developed that induces consistent, daily high-level ethanol consumption. This multiple-session procedure employed 4 drinking sessions per day, with sessions occurring once every 6 hours. The group average alcohol consumption was 4.6 g/kg/d (SEM 0.4), roughly twice the group average consumption of previous reports. Ethanol drinking sessions produced group mean blood ethanol levels of 95 mg/dl after 60 minutes, and fine motor control was impaired up to 90 minutes after a drinking session. This model of multiple-session, limited access, oral ethanol self-dosing produced consistent, high-level ethanol consumption with each session qualifying as a "binge" drinking session using the definition of "binge" provided by the NIAAA (>80 mg/dl/session). This model of ethanol drinking in macaques will be of great utility in the study of immunological, physiological and behavioral effects of ethanol in nonhuman primates.

Fumonisin contamination and fumonisin producing black Aspergilli in dried vine fruits of different origin.

PubMed

Varga, J; Kocsubé, S; Suri, K; Szigeti, Gy; Szekeres, A; Varga, M; Tóth, B; Bartók, T

2010-10-15

Aspergillus niger isolates are able to produce fumonisins in high quantities on agar media with a low water activity. Several agricultural products fit this criterion, including dried vine fruits, dates and figs. Data on the occurrence and role of this species in fumonisin contamination of agricultural products with high sugar content are needed to clarify the importance of A. niger in human health. The mycobiota and fumonisin contamination of various dried vine fruit samples collected from different countries were examined to clarify the role of black Aspergilli in fumonisin contamination of such products. All except two of the examined samples were contaminated with black Aspergilli. Species assignment of the isolates was carried out using sequence analysis of part of the calmodulin gene. The range of fumonisin isomers present in the raisins samples, and produced by A. niger isolates collected from dried vine fruits was also examined using reversed-phase high-performance liquid chromatography/electrospray ionization-ion trap mass spectrometry (RP-HPLC/ESI-ITMS). Among the 30 A. niger/A. awamori isolates identified, 20 were found to be able to produce fumonisins (average contamination: 5.16 mg/kg; range: 0.017-19.6 mg/kg). The average fumonisin content of the 7 dried vine fruit samples which were found to be contaminated by potential fumonisin producing black Aspergilli was 7.22 mg/kg (range: 4.55-35.49 mg/kg). The isolates produced several fumonisin isomers also present in the dried vine fruit samples, including fumonisins B(1-4), 3-epi-FB(3), 3-epi-FB(4), iso-FB(1), and two iso-FB(2,3) forms. Fumonisin B(1) was detected for the first time in A. niger cultures. Most of these isomers have previously only been identified in Fusarium species. Our data indicate that A. niger and A. awamori are responsible for fumonisin contamination of dried vine fruits worldwide. The observed levels of contamination are alarming and pose a new threat for food safety. Copyright © 2010 Elsevier B.V. All rights reserved.

Psychosocial and demographic variables associated with consumer intention to purchase sustainably produced foods as defined by the Midwest Food Alliance.

PubMed

Robinson, Ramona; Smith, Chery

2002-01-01

To examine psychosocial and demographic variables associated with consumer intention to purchase sustainably produced foods using an expanded Theory of Planned Behavior. Consumers were approached at the store entrance and asked to complete a self-administered survey. Three metropolitan Minnesota grocery stores. Participants (n = 550) were adults who shopped at the store: the majority were white, female, and highly educated and earned >or= 50,000 dollars/year. Participation rates averaged 62%. The major domain investigated was consumer support for sustainably produced foods. Demographics, beliefs, attitudes, subjective norm, and self-identity and perceived behavioral control were evaluated as predictors of intention to purchase them. Descriptive statistics, independent t tests, one-way analysis of variance, Pearson product moment correlation coefficients, and stepwise multiple regression analyses (P <.05). Consumers were supportive of sustainably produced foods but not highly confident in their ability to purchase them. Independent predictors of intention to purchase them included attitudes, beliefs, perceived behavioral control, subjective norm, past buying behavior, and marital status. Beliefs, attitudes, and confidence level may influence intention to purchase sustainably produced foods. Nutrition educators could increase consumers' awareness of sustainably produced foods by understanding their beliefs, attitudes, and confidence levels.

Measuring the motor output of the pontomedullary reticular formation in the monkey: do stimulus-triggered averaging and stimulus trains produce comparable results in the upper limbs?

PubMed

Herbert, Wendy J; Davidson, Adam G; Buford, John A

2010-06-01

The pontomedullary reticular formation (PMRF) of the monkey produces motor outputs to both upper limbs. EMG effects evoked from stimulus-triggered averaging (StimulusTA) were compared with effects from stimulus trains to determine whether both stimulation methods produced comparable results. Flexor and extensor muscles of scapulothoracic, shoulder, elbow, and wrist joints were studied bilaterally in two male M. fascicularis monkeys trained to perform a bilateral reaching task. The frequency of facilitation versus suppression responses evoked in the muscles was compared between methods. Stimulus trains were more efficient (94% of PMRF sites) in producing responses than StimulusTA (55%), and stimulus trains evoked responses from more muscles per site than from StimulusTA. Facilitation (72%) was more common from stimulus trains than StimulusTA (39%). In the overall results, a bilateral reciprocal activation pattern of ipsilateral flexor and contralateral extensor facilitation was evident for StimulusTA and stimulus trains. When the comparison was restricted to cases where both methods produced a response in a given muscle from the same site, agreement was very high, at 80%. For the remaining 20%, discrepancies were accounted for mainly by facilitation from stimulus trains when StimulusTA produced suppression, which was in agreement with the under-representation of suppression in the stimulus train data as a whole. To the extent that the stimulus train method may favor transmission through polysynaptic pathways, these results suggest that polysynaptic pathways from the PMRF more often produce facilitation in muscles that would typically demonstrate suppression with StimulusTA.

Applications of High-Resolution Electrospray Ionization Mass Spectrometry to Measurements of Average Oxygen to Carbon Ratios in Secondary Organic Aerosols

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bateman, Adam P.; Laskin, Julia; Laskin, Alexander

2012-07-02

The applicability of high resolution electrospray ionization mass spectrometry (HR ESI-MS) to measurements of the average oxygen to carbon ratio (O/C) in organic aerosols was investigated. Solutions with known average O/C containing up to 10 standard compounds representative of secondary organic aerosol (SOA) were analyzed and corresponding electrospray ionization efficiencies were quantified. The assumption of equal ionization efficiency commonly used in estimating O/C ratios of organic aerosols was found to be reasonably accurate. We found that the accuracy of the measured O/C ratios increases by averaging the values obtained from both (+) and (-) modes. A correlation was found betweenmore » the ratio of the ionization efficiencies in the positive and negative ESI modes with the octanol-water partition constant, and more importantly, with the compound's O/C. To demonstrate the utility of this correlation for estimating average O/C values of unknown mixtures, we analyzed the ESI (+) and ESI (-) data for SOA produced by oxidation of limonene and isoprene and compared to online O/C measurements using an aerosol mass spectrometer (AMS). This work demonstrates that the accuracy of the HR ESI-MS methods is comparable to that of the AMS, with the added benefit of molecular identification of the aerosol constituents.« less

Average stopping powers for electron and photon sources for radiobiological modeling and microdosimetric applications

NASA Astrophysics Data System (ADS)

Vassiliev, Oleg N.; Kry, Stephen F.; Grosshans, David R.; Mohan, Radhe

2018-03-01

This study concerns calculation of the average electronic stopping power for photon and electron sources. It addresses two problems that have not yet been fully resolved. The first is defining the electron spectrum used for averaging in a way that is most suitable for radiobiological modeling. We define it as the spectrum of electrons entering the sensitive to radiation volume (SV) within the cell nucleus, at the moment they enter the SV. For this spectrum we derive a formula that combines linearly the fluence spectrum and the source spectrum. The latter is the distribution of initial energies of electrons produced by a source. Previous studies used either the fluence or source spectra, but not both, thereby neglecting a part of the complete spectrum. Our derived formula reduces to these two prior methods in the case of high and low energy sources, respectively. The second problem is extending electron spectra to low energies. Previous studies used an energy cut-off on the order of 1 keV. However, as we show, even for high energy sources, such as 60Co, electrons with energies below 1 keV contribute about 30% to the dose. In this study all the spectra were calculated with Geant4-DNA code and a cut-off energy of only 11 eV. We present formulas for calculating frequency- and dose-average stopping powers, numerical results for several important electron and photon sources, and tables with all the data needed to use our formulas for arbitrary electron and photon sources producing electrons with initial energies up to  ∼1 MeV.

High average power, highly brilliant laser-produced plasma source for soft X-ray spectroscopy.

PubMed

Mantouvalou, Ioanna; Witte, Katharina; Grötzsch, Daniel; Neitzel, Michael; Günther, Sabrina; Baumann, Jonas; Jung, Robert; Stiel, Holger; Kanngiesser, Birgit; Sandner, Wolfgang

2015-03-01

In this work, a novel laser-produced plasma source is presented which delivers pulsed broadband soft X-radiation in the range between 100 and 1200 eV. The source was designed in view of long operating hours, high stability, and cost effectiveness. It relies on a rotating and translating metal target and achieves high stability through an on-line monitoring device using a four quadrant extreme ultraviolet diode in a pinhole camera arrangement. The source can be operated with three different laser pulse durations and various target materials and is equipped with two beamlines for simultaneous experiments. Characterization measurements are presented with special emphasis on the source position and emission stability of the source. As a first application, a near edge X-ray absorption fine structure measurement on a thin polyimide foil shows the potential of the source for soft X-ray spectroscopy.

Molecular characterization and comparison of shale oils generated by different pyrolysis methods using FT-ICR mass spectrometry

USGS Publications Warehouse

Jin, J.M.; Kim, S.; Birdwell, J.E.

2011-01-01

Fourier transform ion cyclotron resonance mass spectrometry (FT ICR-MS) was applied in the analysis of shale oils generated using two different pyrolysis systems under laboratory conditions meant to simulate surface and in situ oil shale retorting. Significant variations were observed in the shale oils, particularly the degree of conjugation of the constituent molecules. Comparison of FT ICR-MS results to standard oil characterization methods (API gravity, SARA fractionation, gas chromatography-flame ionization detection) indicated correspondence between the average Double Bond Equivalence (DBE) and asphaltene content. The results show that, based on the average DBE values and DBE distributions of the shale oils examined, highly conjugated species are enriched in samples produced under low pressure, high temperature conditions and in the presence of water.

Process for fabricating ZnO-based varistors

DOEpatents

Lauf, R.J.

The invention is a process for producing ZnO-based varistors incorporating a metal oxide dopant. In one form, the invention comprises providing a varistor powder mix of colloidal particles of ZnO and metal-oxide dopants including Bi/sub 2/O/sub 3/. The mix is hot-pressed to form a compact at temperatures below 850/sup 0/C and under conditions effecting reduction of the ZnO to sub-stoichiometric oxide. This promotes densification while restricting liquid formation and grain growth. The compact then is heated under conditions restoring the zinc oxide to stoichiometric composition, thus improving the varistor properties of the compact. The process produces fine-grain varistors characterized by a high actual breakdown voltage and a high average breakdown voltage per individual grain boundary.

Process for fabricating ZnO-based varistors

DOEpatents

Lauf, Robert J.

1985-01-01

The invention is a process for producing ZnO-based varistors incorporating a metal oxide dopant. In one form, the invention comprises providing a varistor powder mix of colloidal particles of ZnO and metal-oxide dopants including Bi.sub.2 O.sub.3. The mix is hot-pressed to form a compact at temperatures below 850.degree. C. and under conditions effecting reduction of the ZnO to sub-stoichiometric oxide. This promotes densification while restricting liquid formation and grain growth. The compact then is heated under conditions restoring the zinc oxide to stoichiometric composition, thus improving the varistor properties of the compact. The process produces fine-grain varistors characterized by a high actual breakdown voltage and a high average breakdown voltage per individual grain boundary.

Image fusion method based on regional feature and improved bidimensional empirical mode decomposition

NASA Astrophysics Data System (ADS)

Qin, Xinqiang; Hu, Gang; Hu, Kai

2018-01-01

The decomposition of multiple source images using bidimensional empirical mode decomposition (BEMD) often produces mismatched bidimensional intrinsic mode functions, either by their number or their frequency, making image fusion difficult. A solution to this problem is proposed using a fixed number of iterations and a union operation in the sifting process. By combining the local regional features of the images, an image fusion method has been developed. First, the source images are decomposed using the proposed BEMD to produce the first intrinsic mode function (IMF) and residue component. Second, for the IMF component, a selection and weighted average strategy based on local area energy is used to obtain a high-frequency fusion component. Third, for the residue component, a selection and weighted average strategy based on local average gray difference is used to obtain a low-frequency fusion component. Finally, the fused image is obtained by applying the inverse BEMD transform. Experimental results show that the proposed algorithm provides superior performance over methods based on wavelet transform, line and column-based EMD, and complex empirical mode decomposition, both in terms of visual quality and objective evaluation criteria.

Hand hygiene compliance rates: Fact or fiction?

PubMed

McLaws, Mary-Louise; Kwok, Yen Lee Angela

2018-05-16

The mandatory national hand hygiene program requires Australian public hospitals to use direct human auditing to establish compliance rates. To establish the magnitude of the Hawthorne effect, we compared direct human audit rates with concurrent automated surveillance rates. A large tertiary Australian teaching hospital previously trialed automated surveillance while simultaneously performing mandatory human audits for 20 minutes daily on a medical and a surgical ward. Subtracting automated surveillance rates from human audit rates provided differences in percentage points (PPs) for each of the 3 quarterly reporting periods for 2014 and 2015. Direct human audit rates for the medical ward were inflated by an average of 55 PPs in 2014 and 64 PPs in 2015, 2.8-3.1 times higher than automated surveillance rates. The rates for the surgical ward were inflated by an average of 32 PPs in 2014 and 31 PPs in 2015, 1.6 times higher than automated surveillance rates. Over the 6 mandatory reporting quarters, human audits collected an average of 255 opportunities, whereas automation collected 578 times more data, averaging 147,308 opportunities per quarter. The magnitude of the Hawthorne effect on direct human auditing was not trivial and produced highly inflated compliance rates. Mandatory compliance necessitates accuracy that only automated surveillance can achieve, whereas daily hand hygiene ambassadors or reminder technology could harness clinicians' ability to hyperrespond to produce habitual compliance. Crown Copyright © 2018. Published by Elsevier Inc. All rights reserved.

Regularized Dual Averaging Image Reconstruction for Full-Wave Ultrasound Computed Tomography.

PubMed

Matthews, Thomas P; Wang, Kun; Li, Cuiping; Duric, Neb; Anastasio, Mark A

2017-05-01

Ultrasound computed tomography (USCT) holds great promise for breast cancer screening. Waveform inversion-based image reconstruction methods account for higher order diffraction effects and can produce high-resolution USCT images, but are computationally demanding. Recently, a source encoding technique has been combined with stochastic gradient descent (SGD) to greatly reduce image reconstruction times. However, this method bundles the stochastic data fidelity term with the deterministic regularization term. This limitation can be overcome by replacing SGD with a structured optimization method, such as the regularized dual averaging method, that exploits knowledge of the composition of the cost function. In this paper, the dual averaging method is combined with source encoding techniques to improve the effectiveness of regularization while maintaining the reduced reconstruction times afforded by source encoding. It is demonstrated that each iteration can be decomposed into a gradient descent step based on the data fidelity term and a proximal update step corresponding to the regularization term. Furthermore, the regularization term is never explicitly differentiated, allowing nonsmooth regularization penalties to be naturally incorporated. The wave equation is solved by the use of a time-domain method. The effectiveness of this approach is demonstrated through computer simulation and experimental studies. The results suggest that the dual averaging method can produce images with less noise and comparable resolution to those obtained by the use of SGD.

Pollen-limited reproduction in blue oak: Implications for wind pollination in fragmented populations

USGS Publications Warehouse

Knapp, E.E.; Goedde, M.A.; Rice, K.J.

2001-01-01

Human activities are fragmenting forests and woodlands worldwide, but the impact of reduced tree population densities on pollen transfer in wind-pollinated trees is poorly understood. In a 4-year study, we evaluated relationships among stand density, pollen availability, and seed production in a thinned and fragmented population of blue oak (Quercus douglasii). Geographic coordinates were established and flowering interval determined for 100 contiguous trees. The number of neighboring trees within 60 m that released pollen during each tree's flowering period was calculated and relationships with acorn production explored using multiple regression. We evaluated the effects of female flower production, average temperature, and relative humidity during the pollination period, and number of pollen-producing neighbors on individual trees' acorn production. All factors except temperature were significant in at least one of the years of our study, but the combination of factors influencing acorn production varied among years. In 1996, a year of large acorn crop size, acorn production was significantly positively associated with number of neighboring pollen producers and density of female flowers. In 1997, 1998, and 1999, many trees produced few or no acorns, and significant associations between number of pollen-producing neighbors and acorn production were only apparent among moderately to highly reproductive trees. Acorn production by these reproductive trees in 1997 was significantly positively associated with number of neighboring pollen producers and significantly negatively associated with average relative humidity during the pollination period. In 1998, no analysis was possible, because too few trees produced a moderate to large acorn crop. Only density of female flowers was significantly associated with acorn production of moderately to highly reproductive trees in 1999. The effect of spatial scale was also investigated by conducting analyses with pollen producers counted in radii ranging from 30 m to 80 m. The association between number of pollen-producing neighbors and acorn production was strongest when neighborhood sizes of 60 m or larger were considered. Our results suggest that fragmentation and thinning of blue oak woodlands may reduce pollen availability and limit reproduction in this wind-pollinated species.

High angle-of-attack aerodynamic characteristics of crescent and elliptic wings

NASA Technical Reports Server (NTRS)

Vandam, C. P.

1989-01-01

Static longitudinal and lateral-directional forces and moments were measured for elliptic- and crescent-wing models at high angles-of-attack in the NASA Langley 14 by 22-Ft Subsonic Tunnel. The forces and moments were obtained for an angle-of-attack range including stall and post-stall conditions at a Reynolds number based on the average wing chord of about 1.8 million. Flow-visualization photographs using a mixture of oil and titanium-dioxide were also taken for several incidence angles. The force and moment data and the flow-visualization results indicated that the crescent wing model with its highly swept tips produced much better high angle-of-attack aerodynamic characteristics than the elliptic model. Leading-edge separation-induced vortex flow over the highly swept tips of the crescent wing is thought to produce this improved behavior at high angles-of-attack. The unique planform design could result in safer and more efficient low-speed airplanes.

Serum concentrations of oestradiol and progesterone and frequency of sexual behaviour during the normal oestrous cycle in the snow leopard (Panthera uncia).

PubMed

Schmidt, A M; Hess, D L; Schmidt, M J; Lewis, C R

1993-05-01

Serum oestradiol and progesterone concentrations were measured at weekly intervals for six months, and correlated with daily behavioural observations in two adult female snow leopards (Panthera uncia). Three oestradiol peaks (> 21 pg ml-1; interval 3.6 weeks) were identified in a snow leopardess housed alone (two more were probably missed because of the weekly sampling schedule), and three oestradiol peaks were identified in a snow leopardess housed with a male as a breeding pair (interval 6 weeks). Daily frequencies of feline reproductive behaviour averaged 1.77 observations per observation period during weeks of high oestradiol and 0.62 during weeks of low oestradiol. Progesterone concentrations did not rise above baseline values (< 2 ng ml-1) in the isolated animal, but 6 weeks of high progesterone concentrations (4.9-38.8 ng ml-1) was recorded in the paired snow leopardess following mating. No offspring were produced. Snow leopards were observed daily for an additional 4.5 years. Sexual behaviour peaks could be clearly identified from December through April, and average daily sexual behaviour scores were higher during these months than during the rest of the year. Intervals between sexual behaviour peaks for the isolated snow leopardess averaged 3.03 weeks. The sexual behaviour of the paired snow leopards decreased for 8-9 weeks following mating when no offspring were produced, and decreased for 13 weeks in one year when a single cub was born.

High-performance thin layer chromatography to assess pharmaceutical product quality.

PubMed

Kaale, Eliangiringa; Manyanga, Vicky; Makori, Narsis; Jenkins, David; Michael Hope, Samuel; Layloff, Thomas

2014-06-01

To assess the sustainability, robustness and economic advantages of high-performance thin layer chromatography (HPTLC) for quality control of pharmaceutical products. We compared three laboratories where three lots of cotrimoxazole tablets were assessed using different techniques for quantifying the active ingredient. The average assay relative standard deviation for the three lots was 1.2 with a range of 0.65-2.0. High-performance thin layer chromatography assessments are yielding valid results suitable for assessing product quality. The local pharmaceutical manufacturer had evolved the capacity to produce very high quality products. © 2014 John Wiley & Sons Ltd.

Real-time control system for adaptive resonator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flath, L; An, J; Brase, J

2000-07-24

Sustained operation of high average power solid-state lasers currently requires an adaptive resonator to produce the optimal beam quality. We describe the architecture of a real-time adaptive control system for correcting intra-cavity aberrations in a heat capacity laser. Image data collected from a wavefront sensor are processed and used to control phase with a high-spatial-resolution deformable mirror. Our controller takes advantage of recent developments in low-cost, high-performance processor technology. A desktop-based computational engine and object-oriented software architecture replaces the high-cost rack-mount embedded computers of previous systems.

Physical evaluations of Co-Cr-Mo parts processed using different additive manufacturing techniques

NASA Astrophysics Data System (ADS)

Ghani, Saiful Anwar Che; Mohamed, Siti Rohaida; Harun, Wan Sharuzi Wan; Noar, Nor Aida Zuraimi Md

2017-12-01

In recent years, additive manufacturing with highly design customization has gained an important technique for fabrication in aerospace and medical fields. Despite the ability of the process to produce complex components with highly controlled architecture geometrical features, maintaining the part's accuracy, ability to fabricate fully functional high density components and inferior surfaces quality are the major obstacles in producing final parts using additive manufacturing for any selected application. This study aims to evaluate the physical properties of cobalt chrome molybdenum (Co-Cr-Mo) alloys parts fabricated by different additive manufacturing techniques. The full dense Co-Cr-Mo parts were produced by Selective Laser Melting (SLM) and Direct Metal Laser Sintering (DMLS) with default process parameters. The density and relative density of samples were calculated using Archimedes' principle while the surface roughness on the top and side surface was measured using surface profiler. The roughness average (Ra) for top surface for SLM produced parts is 3.4 µm while 2.83 µm for DMLS produced parts. The Ra for side surfaces for SLM produced parts is 4.57 µm while 9.0 µm for DMLS produced parts. The higher Ra values on side surfaces compared to the top faces for both manufacturing techniques was due to the balling effect phenomenon. The yield relative density for both Co-Cr-Mo parts produced by SLM and DMLS are 99.3%. Higher energy density has influence the higher density of produced samples by SLM and DMLS processes. The findings of this work demonstrated that SLM and DMLS process with default process parameters have effectively produced full dense parts of Co-Cr-Mo with high density, good agreement of geometrical accuracy and better surface finish. Despite of both manufacturing process yield that produced components with higher density, the current finding shows that SLM technique could produce components with smoother surface quality compared to DMLS process with default parameters.

Biological effectiveness of nuclear fragments produced by high-energy protons interacting in tissues near the bone- soft tissue interface

NASA Astrophysics Data System (ADS)

Shavers, Mark Randall

1999-12-01

High-energy protons in the galactic cosmic rays (GCR)-or generated by nuclear interactions of GCR heavy-ions with material-are capable of penetrating great thicknesses of shielding to irradiate humans in spacecraft or in lunar or Martian habitats. As protons interact with the nuclei of the elemental constituents of soft tissue and bone, low energy nuclei-target fragments-are emitted into the cells responsible for bone development and maintenance and for hematopoiesis. Leukemogenesis is the principal endpoint of concern because it is the most likely deleterious effect, and it has a short latency period and comparatively low survival rate, although other myelo- proliferative disorders and osteosarcoma also may be induced. A one-dimensional proton-target fragment transport model was used to calculate the energy spectra of fragments produced in bone and soft tissue, and present in marrow cavities at distances from a bone interface. In terms of dose equivalent, the target fragments are as significant as the incident protons. An average radiation quality factor was found to be between 1.8 and 2.6. Biological response to the highly non- uniform energy deposition of the target fragments is such that an alternative approach to conventional predictive risk assessment is needed. Alternative procedures are presented. In vitro cell response and relative biological effectiveness were calculated from the radial dose distribution of each fragment produced by 1-GeV protons using parameters of a modified Ion-Gamma- Kill (IGK) model of radiation action. The modelled endpoints were survival of C3H10t 1/2 and V79 cells, neoplastic transformation of C3H10t1/2 cells, and mutation of the X-linked hypoxanthine phosphoribosyltransferase (HPRT) locus in V79 cells. The dose equivalent and cell responses increased by 10% or less near the interface. Since RBE increases with decreasing dose in the IGK model, comparisons with quality factors were made at dose levels 0.01 <= D [Gy] <= 2. Applying average quality factors derived herein to GCR exposures results in a <= 5% increase of in average quality. Calculated RBEs indicate that accepted quality factors for high-energy protons may be too low due to the relatively high effectiveness of the low-charged target fragments. Derived RBEs for target fragments increase the calculated biological effectiveness of GCR by 20% to 180%.

Free-piston driver performance characterisation using experimental shock speeds through helium

NASA Astrophysics Data System (ADS)

Gildfind, D. E.; James, C. M.; Morgan, R. G.

2015-03-01

Tuned free-piston driver operation involves configuring the driver to produce a relatively steady blast of driver gas over the critical time scales of the experiment. For the purposes of flow condition development and parametric studies, it is useful to establish some average working values of the driver pressure and temperature for a given driver operating condition. However, in practise, these averaged values need to produce sufficiently accurate estimates of performance. In this study, two tuned driver conditions in the X2 expansion tube have been used to generate shock waves through a helium test gas. The measured shock speeds have then been used to calculate the effective driver gas pressure and temperature after diaphragm rupture. Since the driver gas is typically helium, or a mixture of helium and argon, and the test gas is also helium, ideal gas assumptions can be made without significant loss of accuracy. The technique is applicable to tuned free-piston drivers with a simple area change, as well as those using orifice plates. It is shown that this technique can be quickly used to establish average working driver gas properties which produce very good estimates of actual driven shock speed, across a wide range of operating conditions. The use of orifice plates to control piston dynamics at high driver gas sound speeds is also discussed in the paper, and a simple technique for calculating the restriction required to modify an established safe condition for use with lighter gases, such as pure helium, is presented.

Scenedesmus obliquus in poultry wastewater bioremediation.

PubMed

Oliveira, Ana Cristina; Barata, Ana; Batista, Ana P; Gouveia, Luísa

2018-06-18

Wastewater biological treatment with microalgae can be an effective technology, removing nutrients and other contaminants while reducing chemical oxygen demand. This can be particularly interesting for the meat producing industry which produces large volumes of wastewater from the slaughtering of animals and cleaning of their facilities. The main purpose of this research was the treatment of poultry wastewater using Scenedesmus obliquus in an economical and environmentally sustainable way. Two wastewaters were collected from a Portuguese poultry slaughterhouse (poultry raw - PR and poultry flocculated - PF) and the bioremediation was evaluated. The performance of microalga biomass growth and biochemical composition were assessed for two illumination sources (fluorescent vs LEDs). S. obliquus achieved positive results when grown in highly contaminated agro-industrial wastewater from the poultry industry, independently of the light source. The wastewater bioremediation revealed results higher than 97% for both ammonium and phosphate removal efficiency, for a cultivation time of 13 days. The saponifiable matter obtained from the biomass of the microalga cultures was, on average, 11% and 27% (m/m alga ) with PR and PF wastewater, respectively. In opposition, higher sugar content was obtained from microalgae biomass grown in PR wastewater (average 34% m/m alga ) in comparison to PF wastewater (average 23% m/m alga ), independently of the illumination source. Therefore, biomass obtained with PR wastewater will be more appropriate as a raw material for bioethanol/biohydrogen production (higher sugar content) while biomass produced in PF wastewater will have a similar potential as feedstock for both biodiesel and bioethanol/biohydrogen production (similar lipid and sugar content).

The Diamond Window with Boron-Doped Layers for the Output of Microwave Radiation at High Peak and Average Power Levels

NASA Astrophysics Data System (ADS)

Ivanov, O. A.; Kuzikov, S. V.; Vikharev, A. A.; Vikharev, A. L.; Lobaev, M. A.

2017-10-01

We propose a novel design of the barrier window for the output of microwave radiation at high peak and average power levels. A window based on a plate of polycrystalline CVD diamond with thin (nanometer-thick) boron-doped layers with increased conductivity is considered. Such a window, which retains the low radiation loss due to the small total thickness of the conductive layers and the high thermal conductivity inherent in diamond, prevents accumulation of a static charge on its surface, on the one hand, and allows one to produce a static electric field on the surface of the doped layer, which impedes the development of a multipactor discharge, on the other hand. In this case, a high level of the power of the transmitted radiation and a large passband width are ensured by choosing the configuration of the field in the form of a traveling wave inside the window.

Taxing energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deacon, R.; DeCanio, S.; Frech, H.E. III

1990-01-01

In this book, the authors have produced an analysis of state energy taxation. Their factual findings are of particular relevance to California and other states in their consideration of severance taxes on oil production. It turns out, for example, that while California's tax burden on oil producers is slightly below average among the states, the combined revenues from taxes and royalties (expressed as a percent of the value of production) indicate that California is not easy on oil producers. In fact, California's oil tax system appears to be particularly well suited to its oil industry. Much of the production inmore » the state is relatively high-cost and economically marginal. The state must tread carefully in taxing this production, lest it force it to be curtailed.« less

Enzyme-resistant dextrins from potato starch for potential application in the beverage industry.

PubMed

Jochym, Kamila Kapusniak; Nebesny, Ewa

2017-09-15

The objective of this study was to produce soluble enzyme-resistant dextrins by microwave heating of potato starch acidified with small amounts of hydrochloric and citric acids and to characterize their properties. Twenty five samples were initially made and their solubility was determined. Three samples with the highest water solubility were selected for physico-chemical (dextrose equivalent, molecular weight distribution, pasting characteristics, retrogradation tendency), total dietary fiber (TDF) analysis, and stability tests. TDF content averaged 25%. Enzyme-resistant dextrins practically did not paste, even at 20% samples concentration, and were characterized by low retrogradation tendency. The stability of the samples, expressed as a percentage increase of initial and final reducing sugar content, at low pH and during heating at low pH averaged 10% and 15% of the initial value, respectively. The results indicate that microwave heating could be an effective and efficient method of producing highly-soluble, low-viscous, and enzyme-resistant potato starch dextrins. Copyright © 2017 Elsevier Ltd. All rights reserved.

The effect of swinging the arms on muscle activation and production of leg force during ski skating at different skiing speeds.

PubMed

Göpfert, Caroline; Lindinger, Stefan J; Ohtonen, Olli; Rapp, Walter; Müller, Erich; Linnamo, Vesa

2016-06-01

The study investigated the effects of arm swing during leg push-off in V2-alternate/G4 skating on neuromuscular activation and force production by the leg muscles. Nine skilled cross-country skiers performed V2-alternate skating without poles at moderate, high, and maximal speeds, both with free (SWING) and restricted arm swing (NOSWING). Maximal speed was 5% greater in SWING (P<0.01), while neuromuscular activation and produced forces did not differ between techniques. At both moderate and high speed the maximal (2% and 5%, respectively) and average (both 5%) vertical force and associated impulse (10% and 14%) were greater with SWING (all P<0.05). At high speed range of motion and angular velocity of knee flexion were 24% greater with SWING (both P<0.05), while average EMG of m. biceps femoris was 31% lower (all P<0.05) in SWING. In a similar manner, the average EMG of m. vastus medialis and m. biceps femoris were lower (17% and 32%, P<0.05) during the following knee extension. Thus, swinging the arms while performing V2-alternate can enhance both maximal speed and skiing economy at moderate and, in particularly, high speeds. Copyright © 2016 Elsevier B.V. All rights reserved.

Natural gas production and anomalous geothermal gradients of the deep Tuscaloosa Formation

USGS Publications Warehouse

Burke, Lauri

2011-01-01

For the largest producing natural gas fields in the onshore Gulf of Mexico Basin, the relation between temperature versus depth was investigated. Prolific natural gas reservoirs with the highest temperatures were found in the Upper Cretaceous downdip Tuscaloosa trend in Louisiana. Temperature and production trends from the deepest field, Judge Digby field, in Pointe Coupe Parish, Louisiana, were investigated to characterize the environment of natural gas in the downdip Tuscaloosa trend. The average production depth in the Judge Digby field is approximately 22,000 ft. Temperatures as high as 400 degrees F are typically found at depth in Judge Digby field and are anomalously low when compared to temperature trends extrapolated to similar depths regionally. At 22,000 ft, the minimum and maximum temperatures for all reservoirs in Gulf Coast producing gas fields are 330 and 550 degrees F, respectively; the average temperature is 430 degrees F. The relatively depressed geothermal gradients in the Judge Digby field may be due to high rates of sediment preservation, which may have delayed the thermal equilibration of the sediment package with respect to the surrounding rock. Analyzing burial history and thermal maturation indicates that the deep Tuscaloosa trend in the Judge Digby field is currently in the gas generation window. Using temperature trends as an exploration tool may have important implications for undiscovered hydrocarbons at greater depths in currently producing reservoirs, and for settings that are geologically analogous to the Judge Digby fiel

A Data Driven Network Approach to Rank Countries Production Diversity and Food Specialization

PubMed Central

Tu, Chengyi; Carr, Joel

2016-01-01

The easy access to large data sets has allowed for leveraging methodology in network physics and complexity science to disentangle patterns and processes directly from the data, leading to key insights in the behavior of systems. Here we use country specific food production data to study binary and weighted topological properties of the bipartite country-food production matrix. This country-food production matrix can be: 1) transformed into overlap matrices which embed information regarding shared production of products among countries, and or shared countries for individual products, 2) identify subsets of countries which produce similar commodities or subsets of commodities shared by a given country allowing for visualization of correlations in large networks, and 3) used to rank country fitness (the ability to produce a diverse array of products weighted on the type of food commodities) and food specialization (quantified on the number of countries producing a specific food product weighted on their fitness). Our results show that, on average, countries with high fitness produce both low and high specializion food commodities, whereas nations with low fitness tend to produce a small basket of diverse food products, typically comprised of low specializion food commodities. PMID:27832118

A Data Driven Network Approach to Rank Countries Production Diversity and Food Specialization.

PubMed

Tu, Chengyi; Carr, Joel; Suweis, Samir

2016-01-01

The easy access to large data sets has allowed for leveraging methodology in network physics and complexity science to disentangle patterns and processes directly from the data, leading to key insights in the behavior of systems. Here we use country specific food production data to study binary and weighted topological properties of the bipartite country-food production matrix. This country-food production matrix can be: 1) transformed into overlap matrices which embed information regarding shared production of products among countries, and or shared countries for individual products, 2) identify subsets of countries which produce similar commodities or subsets of commodities shared by a given country allowing for visualization of correlations in large networks, and 3) used to rank country fitness (the ability to produce a diverse array of products weighted on the type of food commodities) and food specialization (quantified on the number of countries producing a specific food product weighted on their fitness). Our results show that, on average, countries with high fitness produce both low and high specializion food commodities, whereas nations with low fitness tend to produce a small basket of diverse food products, typically comprised of low specializion food commodities.

A balanced microbiota efficiently produces methane in a novel high-rate horizontal anaerobic reactor for the treatment of swine wastewater.

PubMed

Duda, Rose Maria; da Silva Vantini, Juliana; Martins, Larissa Scattolin; de Mello Varani, Alessandro; Lemos, Manoel Victor Franco; Ferro, Maria Inês Tiraboschi; de Oliveira, Roberto Alves

2015-12-01

A novel combination of structurally simple, high-rate horizontal anaerobic reactors installed in series was used to treat swine wastewater. The reactors maintained stable pH, alkalinity, and volatile acid levels. Removed chemical oxygen demand (COD) represented 68% of the total, and the average specific methane production was 0.30L CH4 (g removed CODtot)(-1). In addition, next-generation sequencing and quantitative real-time PCR analyses were used to explore the methane-producing Archaea and microbial diversity. At least 94% of the sludge diversity belong to the Bacteria and Archaea, indicating a good balance of microorganisms. Among the Bacteria the Proteobacteria, Bacteroidetes and Firmicutes were the most prevalent phyla. Interestingly, up to 12% of the sludge diversity belongs to methane-producing orders, such as Methanosarcinales, Methanobacteriales and Methanomicrobiales. In summary, this system can efficiently produce methane and this is the first time that horizontal anaerobic reactors have been evaluated for the treatment of swine wastewater. Copyright © 2015 Elsevier Ltd. All rights reserved.

Method of generating hydrocarbon reagents from diesel, natural gas and other logistical fuels

DOEpatents

Herling, Darrell R [Richland, WA; Aardahl, Chris L [Richland, WA; Rozmiarek, Robert T [Middleton, WI; Rappe, Kenneth G [Richland, WA; Wang, Yong [Richland, WA; Holladay, Jamelyn D [Kennewick, WA

2010-06-29

The present invention provides a process for producing reagents for a chemical reaction by introducing a fuel containing hydrocarbons into a flash distillation process wherein the fuel is separated into a first component having a lower average molecular weight and a second component having a higher average molecular weight. The first component is then reformed to produce synthesis gas wherein the synthesis gas is reacted catalytically to produce the desire reagent.

Method of Generating Hydrocarbon Reagents from Diesel, Natural Gas and Other Logistical Fuels

DOEpatents

Herling, Darrell R [Richland, WA; Aardahl, Chris L [Richland, WA; Rozmiarek, Robert T [Middleton, WI; Rappe, Kenneth G [Richland, WA; Wang, Yong [Richland, WA; Holladay, Jamelyn D [Kennewick, WA

2008-10-14

The present invention provides a process for producing reagents for a chemical reaction by introducing a fuel containing hydrocarbons into a flash distillation process wherein the fuel is separated into a first component having a lower average molecular weight and a second component having a higher average molecular weight. The first component is then reformed to produce synthesis gas wherein the synthesis gas is reacted catalytically to produce the desire reagent.

Increased Anatomical Specificity of Neuromodulation via Modulated Focused Ultrasound

PubMed Central

Mehić, Edin; Xu, Julia M.; Caler, Connor J.; Coulson, Nathaniel K.; Moritz, Chet T.; Mourad, Pierre D.

2014-01-01

Transcranial ultrasound can alter brain function transiently and nondestructively, offering a new tool to study brain function now and inform future therapies. Previous research on neuromodulation implemented pulsed low-frequency (250–700 kHz) ultrasound with spatial peak temporal average intensities (ISPTA) of 0.1–10 W/cm2. That work used transducers that either insonified relatively large volumes of mouse brain (several mL) with relatively low-frequency ultrasound and produced bilateral motor responses, or relatively small volumes of brain (on the order of 0.06 mL) with relatively high-frequency ultrasound that produced unilateral motor responses. This study seeks to increase anatomical specificity to neuromodulation with modulated focused ultrasound (mFU). Here, ‘modulated’ means modifying a focused 2-MHz carrier signal dynamically with a 500-kHz signal as in vibro-acoustography, thereby creating a low-frequency but small volume (approximately 0.015 mL) source of neuromodulation. Application of transcranial mFU to lightly anesthetized mice produced various motor movements with high spatial selectivity (on the order of 1 mm) that scaled with the temporal average ultrasound intensity. Alone, mFU and focused ultrasound (FUS) each induced motor activity, including unilateral motions, though anatomical location and type of motion varied. Future work should include larger animal models to determine the relative efficacy of mFU versus FUS. Other studies should determine the biophysical processes through which they act. Also of interest is exploration of the potential research and clinical applications for targeted, transcranial neuromodulation created by modulated focused ultrasound, especially mFU’s ability to produce compact sources of ultrasound at the very low frequencies (10–100s of Hertz) that are commensurate with the natural frequencies of the brain. PMID:24504255

Susceptibility to Myxobolus cerebralis among Tubifex tubifex populations from ten major drainage basins in Colorado where Cutthroat Trout are endemic.

PubMed

Nehring, R Barry; Lukacs, P M; Baxa, D V; Stinson, M E T; Chiaramonte, L; Wise, S K; Poole, B; Horton, A

2014-03-01

Establishment of Myxobolus cerebralis (Mc) resulted in declines of wild Rainbow Trout Oncorhynchus mykiss populations in streams across Colorado during the 1990s. However, the risk for establishment and spread of this parasite into high-elevation habitats occupied by native Cutthroat Trout O. clarkii was unknown. Beginning in 2003, tubificid worms were collected from all major drainages where Cutthroat Trout were endemic and were assayed by quantitative PCR to determine the occurrence and distribution of the various lineages of Tubifex tubifex (Tt) oligochaetes. Over a 5-year period, 40 groups of Tt oligochaetes collected from 27 streams, 3 natural lakes, 2 private ponds, and a reservoir were evaluated for their relative susceptibility to Mc. Exposure groups were drawn from populations of pure lineage III Tt, mixed-lineage populations where one or more of the highly resistant (lineage I) or nonsusceptible lineages (V or VI) were the dominant oligochaete and susceptible lineage III worms were the subdominant worm, or pure lineage VI Tt. Experimental replicates of 250 oligochaetes were exposed to 50 Mc myxospores per worm. The parasite amplification ratio (total triactinomyxons [TAMs] produced / total myxospore exposure) was very high among all pure lineage III Colorado exposure groups, averaging 363 compared with 8.24 among the mixed-lineage exposure groups. Lineage III oligochaetes from Mt. Whitney Hatchery in California, which served as the laboratory standard for comparative purposes, had an average parasite amplification ratio of 933 among 10 exposed replicates over a 5-year period. Lineage I oligochaetes were highly resistant to infection and did not produce any TAMs. Lineages V and VI Tt did not become infected and did not produce any TAMs. These results suggest that the risk of establishment of Mc is high for aquatic habitats in Colorado where Cutthroat Trout and lineage III Tt are sympatric.

High average daily intake of PCDD/Fs and serum levels in residents living near a deserted factory producing pentachlorophenol (PCP) in Taiwan: influence of contaminated fish consumption.

PubMed

Lee, C C; Lin, W T; Liao, P C; Su, H J; Chen, H L

2006-05-01

An abandoned pentachlorophenol plant and nearby area in southern Taiwan was heavily contaminated by dioxins, impurities formed in the PCP production process. The investigation showed that the average serum PCDD/Fs of residents living nearby area (62.5 pg WHO-TEQ/g lipid) was higher than those living in the non-polluted area (22.5 and 18.2 pg WHO-TEQ/g lipid) (P<0.05). In biota samples, average PCDD/F of milkfish in sea reservoir (28.3 pg WHO-TEQ/g) was higher than those in the nearby fish farm (0.15 pg WHO-TEQ/g), and Tilapia and shrimp showed the similar trend. The average daily PCDD/Fs intake of 38% participants was higher than 4 pg WHO-TEQ/kg/day suggested by the world health organization. Serum PCDD/F was positively associated with average daily intake (ADI) after adjustment for age, sex, BMI, and smoking status. In addition, a prospective cohort study is suggested to determine the long-term health effects on the people living near factory.

A Simple Method for High-Lift Propeller Conceptual Design

NASA Technical Reports Server (NTRS)

Patterson, Michael; Borer, Nick; German, Brian

2016-01-01

In this paper, we present a simple method for designing propellers that are placed upstream of the leading edge of a wing in order to augment lift. Because the primary purpose of these "high-lift propellers" is to increase lift rather than produce thrust, these props are best viewed as a form of high-lift device; consequently, they should be designed differently than traditional propellers. We present a theory that describes how these props can be designed to provide a relatively uniform axial velocity increase, which is hypothesized to be advantageous for lift augmentation based on a literature survey. Computational modeling indicates that such propellers can generate the same average induced axial velocity while consuming less power and producing less thrust than conventional propeller designs. For an example problem based on specifications for NASA's Scalable Convergent Electric Propulsion Technology and Operations Research (SCEPTOR) flight demonstrator, a propeller designed with the new method requires approximately 15% less power and produces approximately 11% less thrust than one designed for minimum induced loss. Higher-order modeling and/or wind tunnel testing are needed to verify the predicted performance.

Screen printing technology applied to silicon solar cell fabrication

NASA Technical Reports Server (NTRS)

Thornhill, J. W.; Sipperly, W. E.

1980-01-01

The process for producing space qualified solar cells in both the conventional and wraparound configuration using screen printing techniques was investigated. Process modifications were chosen that could be easily automated or mechanized. Work was accomplished to optimize the tradeoffs associated with gridline spacing, gridline definition and junction depth. An extensive search for possible front contact metallization was completed. The back surface field structures along with the screen printed back contacts were optimized to produce open circuit voltages of at least an average of 600 millivolts. After all intended modifications on the process sequence were accomplished, the cells were exhaustively tested. Electrical tests at AMO and 28 C were made before and after boiling water immersion, thermal shock, and storage under conditions of high temperature and high humidity.

The development of enabling technologies for producing active interrogation beams.

PubMed

Kwan, Thomas J T; Morgado, Richard E; Wang, Tai-Sen F; Vodolaga, B; Terekhin, V; Onischenko, L M; Vorozhtsov, S B; Samsonov, E V; Vorozhtsov, A S; Alenitsky, Yu G; Perpelkin, E E; Glazov, A A; Novikov, D L; Parkhomchuk, V; Reva, V; Vostrikov, V; Mashinin, V A; Fedotov, S N; Minayev, S A

2010-10-01

A U.S./Russian collaboration of accelerator scientists was directed to the development of high averaged-current (∼1 mA) and high-quality (emittance ∼15 πmm mrad; energy spread ∼0.1%) 1.75 MeV proton beams to produce active interrogation beams that could be applied to counterterrorism. Several accelerator technologies were investigated. These included an electrostatic tandem accelerator of novel design, a compact cyclotron, and a storage ring with energy compensation and electron cooling. Production targets capable of withstanding the beam power levels were designed, fabricated, and tested. The cyclotron/storage-ring system was theoretically studied and computationally designed, and the electrostatic vacuum tandem accelerator at BINP was demonstrated for its potential in active interrogation of explosives and special nuclear materials.

Mutation Breeding of β-carotene Producing Strain B. trispora by Low Energy Ion Implantation

NASA Astrophysics Data System (ADS)

Zhang, Ning; Yu, Long

2009-02-01

Ion beam bioengineering technology as a new mutation approach has been widely used in the biological breeding field. In this paper the application of low energy nitrogen ion implantation in the β-carotene producing strain, Blakeslea trispora(-) was investigated. The effects of different fermentation conditions on β-carotene production by a high yield strain were examined. Results showed that two β-carotene high yielding strains B.trispora(-) BH3-701 and BH3-728 were screened out and the averaged production of β-carotene was raised by 178.7% and 164.6% respectively after five passages in the shaking flasks. Compared with the original strain, the highest yield strain BH3-701 was potent in accumulating β-carotene, especially in the later stage, and greatly increased production efficiency.

High-Strength Aluminum Casting Alloy for High-Temperature Applications (MSFC Center Director's Discretionary Fund Final Project No. 97-10)

NASA Technical Reports Server (NTRS)

Lee, J. A.

1998-01-01

A new aluminum-silicon alloy has been successfully developed at Marshall Space Flight Center that has a significant improvement in tensile strength at elevated temperatures (550 to 700 F). For instance, the new alloy shows in average tensile strength of at least 90 percent higher than the current 390 aluminum piston alloy tested at 500 F. Compared to conventional aluminum alloys, automotive engines using the new piston alloy will have improved gas mileage, and may produce less air pollution in order to meet the future U.S. automotive legislative requirements for low hydrocarbon emissions. The projected cost for this alloy is less than $0.95/lb, and it readily allows the automotive components to be cast at a high production volume with a low, fully accounted cost. It is economically produced by pouring molten metal directly into conventional permanent steel molds or die casting.

Teleseismic P wave tomography of South Island, New Zealand upper mantle: Evidence of subduction of Pacific lithosphere since 45 Ma

NASA Astrophysics Data System (ADS)

Zietlow, Daniel W.; Molnar, Peter H.; Sheehan, Anne F.

2016-06-01

A P wave speed tomogram produced from teleseismic travel time measurements made on and offshore the South Island of New Zealand shows a nearly vertical zone with wave speeds that are 4.5% higher than the background average reaching to depths of approximately 450 km under the northwestern region of the island. This structure is consistent with oblique west-southwest subduction of Pacific lithosphere since about 45 Ma, when subduction beneath the region began. The high-speed zone reaches about 200-300 km below the depths of the deepest intermediate-depth earthquakes (subcrustal to ~200 km) and therefore suggests that ~200-300 km of slab below them is required to produce sufficient weight to induce the intermediate-depth seismicity. In the southwestern South Island, high P wave speeds indicate subduction of the Australian plate at the Puysegur Trench to approximately 200 km depth. A band with speeds ~2-3.5% lower than the background average is found along the east coast of the South Island to depths of ~150-200 km and underlies Miocene or younger volcanism; these low speeds are consistent with thinned lithosphere. A core of high speeds under the Southern Alps associated with a convergent margin and mountain building imaged in previous investigations is not well resolved in this study. This could suggest that such high speeds are limited in both width and depth and not resolvable by our data.

Religious Burning as a Major Source of Atmospheric Fine Aerosols in Lhasa city in the Tibetan Plateau

NASA Astrophysics Data System (ADS)

Liu, S.; Cui, Y.; Zhixuan, B.; Bian, J.; McKeen, S. A.; Watts, L. A.; Ciciora, S. J.; Gao, R. S.

2017-12-01

Measurements of aerosols in the Tibetan Plateau are scant due to the high altitude and harsh climate. To bridge this gap, we carried out the first field measurements of aerosol size distributions in Lhasa, a major city in the Tibetan Plateau that has been experiencing fast urbanization and reduced air quality. Aerosol number size distribution was continuously measured using an optical particle size spectrometer near the center of Lhasa city during the Asian summer monsoon season in 2016. The mass concentration of fine particles was modulated by boundary layer dynamics, with an average of 11 µg m-3 and the high values exceeding 50 µg m-3 during religious holidays. Daytime high concentration coincided with the religious burning of biomass and incense in the temples during morning hours, which produced heavy smoke. Factor analysis revealed a factor that is likely induced by religious burning. The factor contributed 34% of the campaign-average fine particle mass and the contribution reached up to 80% during religious holidays. The mass size distribution of aerosols produced from religious burnings peaked at 500 nm, indicating that these particles could efficiently decrease visibility and promote health risk. Because of its significance, our results suggest that more attention should be paid to religious burning, a currently under-studied source, in the Tibetan Plateau and in other regions of the world where religious burnings are frequently practiced.

An Effectiveness Trial of a New Enhanced Dissonance Eating Disorder Prevention Program among Female College Students

PubMed Central

Stice, Eric; Butryn, Meghan L.; Rohde, Paul; Shaw, Heather; Marti, C. Nathan

2014-01-01

Objective Efficacy trials indicate that a dissonance-based prevention program in which female high school and college students with body image concerns critique the thin-ideal reduced risk factors, eating disorder symptoms, and future eating disorder onset, but weaker effects emerged from an effectiveness trial wherein high school clinicians recruited students and delivered the program under real-world conditions. The present effectiveness trial tested whether a new enhanced dissonance version of this program produced larger effects when college clinicians recruited students and delivered the intervention using improved procedures to select, train, and supervise clinicians. Method Young women recruited from seven universities across the US (N = 408, M age = 21.6, SD = 5.64) were randomized to the dissonance intervention or an educational brochure control condition. Results Dissonance participants showed significantly greater decreases in risk factors (thin-ideal internalization, body dissatisfaction, dieting, negative affect) and eating disorder symptoms versus controls at posttest and 1-year follow-up, resulting in medium average effect size (d = .60). Dissonance participants also reported significant improvements in psychosocial functioning, but not reduced healthcare utilization or unhealthy weight gain. Conclusions This novel multisite effectiveness trial with college clinicians found that the enhanced dissonance version of this program and the improved facilitator selection/training procedures produced average effects that were 83% larger than effects observed in the high school effectiveness trial. PMID:24189570

Biological Control Products for Aflatoxin Prevention in Italy: Commercial Field Evaluation of Atoxigenic Aspergillus flavus Active Ingredients.

PubMed

Mauro, Antonio; Garcia-Cela, Esther; Pietri, Amedeo; Cotty, Peter J; Battilani, Paola

2018-01-05

Since 2003, non-compliant aflatoxin concentrations have been detected in maize produced in Italy. The most successful worldwide experiments in aflatoxin prevention resulted from distribution of atoxigenic strains of Aspergillus flavus to displace aflatoxin-producers during crop development. The displacement results in lower aflatoxin concentrations in harvested grain. The current study evaluated in field performances of two atoxigenic strains of A . flavus endemic to Italy in artificially inoculated maize ears and in naturally contaminated maize. Co-inoculation of atoxigenic strains with aflatoxin producers resulted in highly significant reductions in aflatoxin concentrations (>90%) in both years only with atoxigenic strain A2085. The average percent reduction in aflatoxin B₁ concentration in naturally contaminated maize fields was 92.3%, without significant differences in fumonisins between treated and control maize. The vegetative compatibility group of A2085 was the most frequently recovered A. flavus in both treated and control plots (average 61.9% and 53.5% of the A. flavus , respectively). A2085 was therefore selected as an active ingredient for biocontrol products and deposited under provisions of the Budapest Treaty in the Belgian Co-Ordinated Collections of Micro-Organisms (BCCM/MUCL) collection (accession MUCL54911). Further work on development of A2085 as a tool for preventing aflatoxin contamination in maize produced in Italy is ongoing with the commercial product named AF-X1™.

The nature of pulsar radio emission

NASA Astrophysics Data System (ADS)

Dyks, J.; Rudak, B.; Demorest, P.

2010-01-01

High-quality averaged radio profiles of some pulsars exhibit double, highly symmetric features both in emission and in absorption. It is shown that both types of feature are produced by a split fan beam of extraordinary-mode curvature radiation that is emitted/absorbed by radially extended streams of magnetospheric plasma. With no emissivity in the plane of the stream, such a beam produces bifurcated emission components (BFCs) when our line of sight passes through the plane. An example of a double component created in this way is present in the averaged profile of the 5-ms pulsar J1012+5307. We show that the component can indeed be very well fitted by the textbook formula for the non-coherent beam of curvature radiation in the polarization state that is orthogonal to the plane of electron trajectory. The observed width of the BFC decreases with increasing frequency at a rate that confirms the curvature origin. Likewise, the double absorption features (double notches) are produced by the same beam of the extraordinary-mode curvature radiation, when it is eclipsed by thin plasma streams. The intrinsic property of curvature radiation to create bifurcated fan beams explains the double features in terms of a very natural geometry and implies the curvature origin of pulsar radio emission. Similarly, the `double conal' profiles of class D result from a cut through a wider stream with finite extent in magnetic azimuth. Therefore, their width reacts very slowly to changes of viewing geometry resulting from geodetic precession. The stream-cut interpretation implies a highly non-orthodox origin of both the famous S-swing of polarization angle and the low-frequency pulse broadening in D profiles. The azimuthal structure of polarization modes in the curvature radiation beam provides an explanation for the polarized `multiple imaging' and the edge depolarization of pulsar profiles.

Robust estimation of event-related potentials via particle filter.

PubMed

Fukami, Tadanori; Watanabe, Jun; Ishikawa, Fumito

2016-03-01

In clinical examinations and brain-computer interface (BCI) research, a short electroencephalogram (EEG) measurement time is ideal. The use of event-related potentials (ERPs) relies on both estimation accuracy and processing time. We tested a particle filter that uses a large number of particles to construct a probability distribution. We constructed a simple model for recording EEG comprising three components: ERPs approximated via a trend model, background waves constructed via an autoregressive model, and noise. We evaluated the performance of the particle filter based on mean squared error (MSE), P300 peak amplitude, and latency. We then compared our filter with the Kalman filter and a conventional simple averaging method. To confirm the efficacy of the filter, we used it to estimate ERP elicited by a P300 BCI speller. A 400-particle filter produced the best MSE. We found that the merit of the filter increased when the original waveform already had a low signal-to-noise ratio (SNR) (i.e., the power ratio between ERP and background EEG). We calculated the amount of averaging necessary after applying a particle filter that produced a result equivalent to that associated with conventional averaging, and determined that the particle filter yielded a maximum 42.8% reduction in measurement time. The particle filter performed better than both the Kalman filter and conventional averaging for a low SNR in terms of both MSE and P300 peak amplitude and latency. For EEG data produced by the P300 speller, we were able to use our filter to obtain ERP waveforms that were stable compared with averages produced by a conventional averaging method, irrespective of the amount of averaging. We confirmed that particle filters are efficacious in reducing the measurement time required during simulations with a low SNR. Additionally, particle filters can perform robust ERP estimation for EEG data produced via a P300 speller. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Comparison between Single-Walled CNT, Multi-Walled CNT, and Carbon Nanotube-Fiber Pyrograf III

NASA Astrophysics Data System (ADS)

Mousa, Marwan S.

2018-02-01

Single-Walled CNT (SWCNTs), Multi-walled Carbon Nanotubes (MWCNTs), and Carbon Nanotube-Fibers Pyrograf III PR-1 (CNTFs) were deposited by chemical vapor deposition under vacuum pressure value of (10-7mbar). Their structures were investigated by field emission microscopy. Carbon Nano-Fibers Pyrograf III PR-1 showed an average fiber diameter within the range of 100-200 nm and a length of (30-100) μm. Single-walled Carbon Nanotubes were produced by high-pressure Carbon Monoxide process with an average diameter ranging between (1-4) nm and a length of (1-3) μm. Thin Multiwall Carbon Nanotube of carbon purity (90%) showed an average diameter tube (9.5 nm) with a high-aspect-ratio (>150). The research work reported here includes the field electron emission current-voltage (I-V) characteristics and presented as Fowler-Nordheim (FN) plots and the spatial emission current distributions (electron emission images) obtained and analyzed in terms of electron source features. For the three types of emitters, a single spot pattern for the electron spatial; distributions were observed, with emission current fluctuations in some voltage region.

Effect of heating rate and plant species on the size and uniformity of silver nanoparticles synthesized using aromatic plant extracts

NASA Astrophysics Data System (ADS)

Hernández-Pinero, Jorge Luis; Terrón-Rebolledo, Manuel; Foroughbakhch, Rahim; Moreno-Limón, Sergio; Melendrez, M. F.; Solís-Pomar, Francisco; Pérez-Tijerina, Eduardo

2016-11-01

Mixing aqueous silver solutions with aqueous leaf aromatic plant extracts from basil, mint, marjoram and peppermint resulted in the synthesis of quasi-spherical silver nanoparticles in a range of size between 2 and 80 nm in diameter as analyzed by analytical high-resolution electron microscopy. The average size could be controlled by applying heat to the initial reaction system at different rates of heating, and by the specific botanical species employed for the reaction. Increasing the rate of heating resulted in a statistically significant decrease in the size of the nanoparticles produced, regardless of the species employed. This fact was more evident in the case of marjoram, which decreased the average diameter from 27 nm at a slow rate of heating to 8 nm at a high rate of heating. With regard to the species, minimum sizes of <10 nm were obtained with basil and peppermint, while marjoram and mint yielded an average size between 10 and 25 nm. The results indicate that aromatic plant extracts can be used to achieve the controlled synthesis of metal nanoparticles.

Short communication: Prevalence of digital dermatitis in Canadian dairy cattle classified as high, average, or low antibody- and cell-mediated immune responders.

PubMed

Cartwright, S L; Malchiodi, F; Thompson-Crispi, K; Miglior, F; Mallard, B A

2017-10-01

Lameness is a major animal welfare issue affecting Canadian dairy producers, and it can lead to production, reproduction, and health problems in dairy cattle herds. Although several different lesions affect dairy cattle hooves, studies show that digital dermatitis is the most common lesion identified in Canadian dairy herds. It has also been shown that dairy cattle classified as having high immune response (IR) have lower incidence of disease compared with those animals with average and low IR; therefore, it has been hypothesized that IR plays a role in preventing infectious hoof lesions. The objective of this study was to compare the prevalence of digital dermatitis in Canadian dairy cattle that were classified for antibody-mediated (AMIR) and cell-mediated (CMIR) immune response. Cattle (n = 329) from 5 commercial dairy farms in Ontario were evaluated for IR using a patented test protocol that captures both AMIR and CMIR. Individuals were classified as high, average, or low responders based on standardized residuals for AMIR and CMIR. Residuals were calculated using a general linear model that included the effects of herd, parity, stage of lactation, and stage of pregnancy. Hoof health data were collected from 2011 to 2013 by the farm's hoof trimmer using Hoof Supervisor software (KS Dairy Consulting Inc., Dresser, WI). All trim events were included for each animal, and lesions were assessed as a binary trait at each trim event. Hoof health data were analyzed using a mixed model that included the effects of herd, stage of lactation (at trim date), parity (at trim date), IR category (high, average, and low), and the random effect of animal. All data were presented as prevalence within IR category. Results showed that cows with high AMIR had significantly lower prevalence of digital dermatitis than cattle with average and low AMIR. No significant difference in prevalence of digital dermatitis was observed between high, average, and low CMIR cows. These results indicate that having more robust AMIR is associated with lower prevalence of digital dermatitis hoof lesions. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Hyper-spectral imaging of aircraft exhaust plumes

NASA Astrophysics Data System (ADS)

Bowen, Spencer; Bradley, Kenneth; Gross, Kevin; Perram, Glen; Marciniak, Michael

2008-10-01

An imaging Fourier-transform spectrometer has been used to determine low spatial resolution temperature and chemical species concentration distributions of aircraft jet engine exhaust plumes. An overview of the imaging Fourier transform spectrometer and the methodology of the project is presented. Results to date are shared and future work is discussed. Exhaust plume data from a Turbine Technologies, LTD, SR-30 turbojet engine at three engine settings was collected using a Telops Field-portable Imaging Radiometric Spectrometer Technology Mid-Wave Extended (FIRST-MWE). Although the plume exhibited high temporal frequency fluctuations, temporal averaging of hyper-spectral data-cubes produced steady-state distributions, which, when co-added and Fourier transformed, produced workable spectra. These spectra were then reduced using a simplified gaseous effluent model to fit forward-modeled spectra obtained from the Line-By-Line Radiative Transfer Model (LBLRTM) and the high-resolution transmission (HITRAN) molecular absorption database to determine approximate temperature and concentration distributions. It is theorized that further development of the physical model will produce better agreement between measured and modeled data.

High-loading-substrate enzymatic hydrolysis of palm plantation waste followed by unsterilized-mixed-culture fermentation for bio-ethanol production

NASA Astrophysics Data System (ADS)

Bardant, Teuku Beuna; Winarni, Ina; Sukmana, Hadid

2017-01-01

It was desired to obtain a general formula for producing bio-ethanol from any part of lignocelluloses wastes that came from palm oil industries due to its abundance. Optimum condition that obtained by using RSM for conducting high-loading-substrate enzymatic hydrolysis of palm oil empty fruit bunch was applied to palm oil trunks and then followed by unsterilized fermentation for producing bio-ethanol. From several optimized conditions investigated, the resulted ethanol concentration could reach 7.92 %v by using 36.5 %w of palm oil trunks but the results were averagely 2.46 %v lower than palm oil empty fruit bunch. The results was statistically compared and showed best correlative coefficient at 0.808 (in scale 0-1) which support the conclusion that the optimum condition for empty fruit bunch and trunks are similar. Utilization of mixed-culture yeast was investigated to produce ethanol from unsterilized hydrolysis product but the improvement wasn't significant compares to single culture yeast.

Biological treatment process for removing petroleum hydrocarbons from oil field produced waters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tellez, G.; Khandan, N.

1995-12-31

The feasibility of removing petroleum hydrocarbons from oil fields produced waters using biological treatment was evaluated under laboratory and field conditions. Based on previous laboratory studies, a field-scale prototype system was designed and operated over a period of four months. Two different sources of produced waters were tested in this field study under various continuous flow rates ranging from 375 1/D to 1,800 1/D. One source of produced water was an open storage pit; the other, a closed storage tank. The TDS concentrations of these sources exceeded 50,000 mg/l; total n-alkanes exceeded 100 mg/l; total petroleum hydrocarbons exceeded 125 mg/l;more » and total BTEX exceeded 3 mg/l. Removals of total n-alkanes, total petroleum hydrocarbons, and BTEX remained consistently high over 99%. During these tests, the energy costs averaged $0.20/bbl at 12 bbl/D.« less

Upgrading producer gas quality from rubber wood gasification in a radio frequency tar thermocatalytic treatment reactor.

PubMed

Anis, Samsudin; Zainal, Z A

2013-12-01

This study focused on improving the producer gas quality using radio frequency (RF) tar thermocatalytic treatment reactor. The producer gas containing tar, particles and water was directly passed at a particular flow rate into the RF reactor at various temperatures for catalytic and thermal treatments. Thermal treatment generates higher heating value of 5.76 MJ Nm(-3) at 1200°C. Catalytic treatments using both dolomite and Y-zeolite provide high tar and particles conversion efficiencies of about 97% on average. The result also showed that light poly-aromatic hydrocarbons especially naphthalene and aromatic compounds particularly benzene and toluene were still found even at higher reaction temperatures. Low energy intensive RF tar thermocatalytic treatment was found to be effective for upgrading the producer gas quality to meet the end user requirements and increasing its energy content. Copyright © 2013 Elsevier Ltd. All rights reserved.

Using Spatial Correlations of SPDC Sources for Increasing the Signal to Noise Ratio in Images

NASA Astrophysics Data System (ADS)

Ruíz, A. I.; Caudillo, R.; Velázquez, V. M.; Barrios, E.

2017-05-01

We experimentally show that, by using spatial correlations of photon pairs produced by Spontaneous Parametric Down-Conversion, it is possible to increase the Signal to Noise Ratio in images of objects illuminated with those photons; in comparison, objects illuminated with light from a laser present a minor ratio. Our simple experimental set-up was capable to produce an average improvement in signal to noise ratio of 11dB of Parametric Down-Converted light over laser light. This simple method can be easily implemented for obtaining high contrast images of faint objects and for transmitting information with low noise.

Metrics for the Diurnal Cycle of Precipitation: Toward Routine Benchmarks for Climate Models

DOE PAGES

Covey, Curt; Gleckler, Peter J.; Doutriaux, Charles; ...

2016-06-08

In this paper, metrics are proposed—that is, a few summary statistics that condense large amounts of data from observations or model simulations—encapsulating the diurnal cycle of precipitation. Vector area averaging of Fourier amplitude and phase produces useful information in a reasonably small number of harmonic dial plots, a procedure familiar from atmospheric tide research. The metrics cover most of the globe but down-weight high-latitude wintertime ocean areas where baroclinic waves are most prominent. This enables intercomparison of a large number of climate models with observations and with each other. The diurnal cycle of precipitation has features not encountered in typicalmore » climate model intercomparisons, notably the absence of meaningful “average model” results that can be displayed in a single two-dimensional map. Displaying one map per model guides development of the metrics proposed here by making it clear that land and ocean areas must be averaged separately, but interpreting maps from all models becomes problematic as the size of a multimodel ensemble increases. Global diurnal metrics provide quick comparisons with observations and among models, using the most recent version of the Coupled Model Intercomparison Project (CMIP). This includes, for the first time in CMIP, spatial resolutions comparable to global satellite observations. Finally, consistent with earlier studies of resolution versus parameterization of the diurnal cycle, the longstanding tendency of models to produce rainfall too early in the day persists in the high-resolution simulations, as expected if the error is due to subgrid-scale physics.« less

Metrics for the Diurnal Cycle of Precipitation: Toward Routine Benchmarks for Climate Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Covey, Curt; Gleckler, Peter J.; Doutriaux, Charles

In this paper, metrics are proposed—that is, a few summary statistics that condense large amounts of data from observations or model simulations—encapsulating the diurnal cycle of precipitation. Vector area averaging of Fourier amplitude and phase produces useful information in a reasonably small number of harmonic dial plots, a procedure familiar from atmospheric tide research. The metrics cover most of the globe but down-weight high-latitude wintertime ocean areas where baroclinic waves are most prominent. This enables intercomparison of a large number of climate models with observations and with each other. The diurnal cycle of precipitation has features not encountered in typicalmore » climate model intercomparisons, notably the absence of meaningful “average model” results that can be displayed in a single two-dimensional map. Displaying one map per model guides development of the metrics proposed here by making it clear that land and ocean areas must be averaged separately, but interpreting maps from all models becomes problematic as the size of a multimodel ensemble increases. Global diurnal metrics provide quick comparisons with observations and among models, using the most recent version of the Coupled Model Intercomparison Project (CMIP). This includes, for the first time in CMIP, spatial resolutions comparable to global satellite observations. Finally, consistent with earlier studies of resolution versus parameterization of the diurnal cycle, the longstanding tendency of models to produce rainfall too early in the day persists in the high-resolution simulations, as expected if the error is due to subgrid-scale physics.« less

40 CFR 80.1238 - How is a refinery's or importer's average benzene concentration determined?

Code of Federal Regulations, 2014 CFR

2014-07-01

... average benzene concentration determined? 80.1238 Section 80.1238 Protection of Environment ENVIRONMENTAL... Benzene Gasoline Benzene Requirements § 80.1238 How is a refinery's or importer's average benzene concentration determined? (a) The average benzene concentration of gasoline produced at a refinery or imported...

40 CFR 80.1238 - How is a refinery's or importer's average benzene concentration determined?

Code of Federal Regulations, 2010 CFR

2010-07-01

... average benzene concentration determined? 80.1238 Section 80.1238 Protection of Environment ENVIRONMENTAL... Benzene Gasoline Benzene Requirements § 80.1238 How is a refinery's or importer's average benzene concentration determined? (a) The average benzene concentration of gasoline produced at a refinery or imported...

40 CFR 80.1238 - How is a refinery's or importer's average benzene concentration determined?

Code of Federal Regulations, 2013 CFR

2013-07-01

... average benzene concentration determined? 80.1238 Section 80.1238 Protection of Environment ENVIRONMENTAL... Benzene Gasoline Benzene Requirements § 80.1238 How is a refinery's or importer's average benzene concentration determined? (a) The average benzene concentration of gasoline produced at a refinery or imported...

40 CFR 80.1238 - How is a refinery's or importer's average benzene concentration determined?

Code of Federal Regulations, 2012 CFR

2012-07-01

... average benzene concentration determined? 80.1238 Section 80.1238 Protection of Environment ENVIRONMENTAL... Benzene Gasoline Benzene Requirements § 80.1238 How is a refinery's or importer's average benzene concentration determined? (a) The average benzene concentration of gasoline produced at a refinery or imported...

40 CFR 80.1238 - How is a refinery's or importer's average benzene concentration determined?

Code of Federal Regulations, 2011 CFR

2011-07-01

... average benzene concentration determined? 80.1238 Section 80.1238 Protection of Environment ENVIRONMENTAL... Benzene Gasoline Benzene Requirements § 80.1238 How is a refinery's or importer's average benzene concentration determined? (a) The average benzene concentration of gasoline produced at a refinery or imported...

The Nation's top 25 construction aggregates producers

USGS Publications Warehouse

Willett, Jason Christopher

2013-01-01

U.S. production of construction aggregates in 2011 was 2.17 billion short tons, valued at $17.2 billion, free on board (f.o.b.) at plant. Construction aggregates production decreased by 37 percent, and the associated value decreased by 25 percent, compared with the record highs reported in 2006. In 2011, construction aggregates production increased for the first time since 2006, owing to a very slight increase in the production of both construction sand and gravel and crushed stone. The average unit value, which is the f.o.b. at plant price of a ton of material, increased slightly, but is still less than the average unit value of two years prior.

High Performance MG-System Alloys For Weight Saving Applications: First Year Results From The Green Metallurgy EU Project

NASA Astrophysics Data System (ADS)

D'Errico, Fabrizio; Plaza, Gerardo Garces; Hofer, Markus; Kim, Shae K.

The GREEN METALLURGY Project, a LIFE+ project co-financed by the EU Commission, has just concluded its first year. The Project seeks to set manufacturing processes at a pre-industrial scale for nanostructured-based high-performance Mg-Zn(Y) magnesium alloys. The Project's goal is the reduction of specific energy consumed and the overall carbon-footprint produced in the cradle-to-exit gate phases. Preliminary results addressed potentialities of the upstream manufacturing process pathway. Two Mg-Zn(Y) system alloys with rapid solidifying powders have been produced and directly extruded for 100% densification. Examination of the mechanical properties showed that such materials exhibit strength and elongation comparable to several high performing aluminum alloys; 390 MPa and 440 MPa for the average UTS for two different system alloys, and 10% and 15% elongations for two system alloys. These results, together with the low-environmental impact targeted, make these novel Mg alloys competitive as lightweight high-performance materials for automotive components.

A modified blade element theory for estimation of forces generated by a beetle-mimicking flapping wing system.

PubMed

Truong, Q T; Nguyen, Q V; Truong, V T; Park, H C; Byun, D Y; Goo, N S

2011-09-01

We present an unsteady blade element theory (BET) model to estimate the aerodynamic forces produced by a freely flying beetle and a beetle-mimicking flapping wing system. Added mass and rotational forces are included to accommodate the unsteady force. In addition to the aerodynamic forces needed to accurately estimate the time history of the forces, the inertial forces of the wings are also calculated. All of the force components are considered based on the full three-dimensional (3D) motion of the wing. The result obtained by the present BET model is validated with the data which were presented in a reference paper. The difference between the averages of the estimated forces (lift and drag) and the measured forces in the reference is about 5.7%. The BET model is also used to estimate the force produced by a freely flying beetle and a beetle-mimicking flapping wing system. The wing kinematics used in the BET calculation of a real beetle and the flapping wing system are captured using high-speed cameras. The results show that the average estimated vertical force of the beetle is reasonably close to the weight of the beetle, and the average estimated thrust of the beetle-mimicking flapping wing system is in good agreement with the measured value. Our results show that the unsteady lift and drag coefficients measured by Dickinson et al are still useful for relatively higher Reynolds number cases, and the proposed BET can be a good way to estimate the force produced by a flapping wing system.

Promoting effects of bile acid to intestinal tumorigenesis in gnotobiotic ICR mice.

PubMed

Iwasaki, I; Iwase, H; Yumoto, N; Ide, G

1985-11-01

Gnotobiotes were produced by administrating Lactobacillus plantarum IAM 1041 in ICR strain male germfree mice which were fed by ordinary or high fat diet. Both groups were orally administered 0.3 mg/10 g of body weight (B.W.) of methylazoxymethanol (MAM) acetate. The oral administration of 0.3 mg/10 g/B.W. once a week for 11 consecutive weeks caused a total of 68 adenomatous polyps in the large intestine (an average of 11.4/mouse) of gnotobiotic high fat diet mice and a total of 32 adenomatous polyps (an average of 5.3/mouse) of the ordinary diet mice. There were no malignancies in either of the groups. Bile acids in the feces showed higher values in the high fat diet group than in the ordinary group. Bile acids are a factor which promotes the appearance of intestinal tumors. It was also assumed that the L. plantarum promoted the activation of beta-glucuronidase and alcohol dehydrogenase in the liver and intestine.

Formulation of stable Bacillus subtilis AH18 against temperature fluctuation with highly heat-resistant endospores and micropore inorganic carriers.

PubMed

Chung, Soohee; Lim, Hyung Mi; Kim, Sang-Dal

2007-08-01

To survive the commercial market and to achieve the desired effect of beneficial organisms, the strains in microbial products must be cost-effectively formulated to remain dormant and hence survive through high and low temperatures of the environment during transportation and storage. Dormancy and stability of Bacillus subtilis AH18 was achieved by producing endospores with enhanced heat resistance and using inorganic carriers. Heat stability assays, at 90 degrees C for 1 h, showed that spores produced under a sublethal temperature of 57 degrees C was 100 times more heat-resistant than the ones produced by food depletion at the growing temperature of 37 degrees C. When these highly heat-resistant endospores were formulated with inorganic carriers of natural and synthetic zeolite or kaolin clay minerals having substantial amount of micropores, the dormancy of the endospores was maintained for 6 months at 15-25 degrees C. Meanwhile, macroporous perlite carriers with average pore diameter larger than 3.7 microm stimulated the germination of the spores and rapid proliferation of the bacteria. These results indicated that a B. subtilis AH18 product that can remain dormant and survive through environmental temperature fluctuation can be formulated by producing heat-stressed endospores and incorporating inorganic carriers with micropores in the formulation step.

High-power picosecond fiber source for coherent Raman microscopy

PubMed Central

Kieu, Khanh; Saar, Brian G.; Holtom, Gary R.; Xie, X. Sunney; Wise, Frank W.

2011-01-01

We report a high-power picosecond fiber pump laser system for coherent Raman microscopy (CRM). The fiber laser system generates 3.5 ps pulses with 6 W average power at 1030 nm. Frequency doubling yields more than 2 W of green light, which can be used to pump an optical parametric oscillator to produce the pump and the Stokes beams for CRM. Detailed performance data on the laser and the various wavelength conversion steps are discussed, together with representative CRM images of fresh animal tissue obtained with the new source. PMID:19571996

Geographical and Geomorphological Effects on Air Temperatures in the Columbia Basin's Signature Vineyards

NASA Astrophysics Data System (ADS)

Olson, L.; Pogue, K. R.; Bader, N.

2012-12-01

The Columbia Basin of Washington and Oregon is one of the most productive grape-growing areas in the United States. Wines produced in this region are influenced by their terroir - the amalgamation of physical and cultural elements that influence grapes grown at a particular vineyard site. Of the physical factors, climate, and in particular air temperature, has been recognized as a primary influence on viticulture. Air temperature directly affects ripening in the grapes. Proper fruit ripening, which requires precise and balanced levels of acid and sugar, and the accumulation of pigment in the grape skin, directly correlates with the quality of wine produced. Many features control air temperature within a particular vineyard. Elevation, latitude, slope, and aspect all converge to form complex relationships with air temperatures; however, the relative degree to which these attributes affect temperatures varies between regions and is not well understood. This study examines the influence of geography and geomorphology on air temperatures within the American Viticultural Areas (AVAs) of the Columbia Basin in eastern Washington and Oregon. The premier vineyards within each AVA, which have been recognized for producing high-quality wine, were equipped with air temperature monitoring stations that collected hourly temperature measurements. A variety of temperature statistics were calculated, including daily average, maximum, and minimum temperatures. From these values, average diurnal variation and growing degree-days (10°C) were calculated. A variety of other statistics were computed, including date of first and last frost and time spent below a minimum temperature threshold. These parameters were compared to the vineyard's elevation, latitude, slope, aspect, and local topography using GPS, ArcCatalog, and GIS in an attempt to determine their relative influences on air temperatures. From these statistics, it was possible to delineate two trends of temperature variation controlled by elevation. In some AVAs, such as Walla Walla Valley and Red Mountain, average air temperatures increased with elevation because of the effect of cold air pooling on valley floors. In other AVAs, such as Horse Heaven Hills, Lake Chelan and Columbia Gorge, average temperatures decreased with elevation due to the moderating influences of the Columbia River and Lake Chelan. Other temperature statistics, including average diurnal range and maximum and minimum temperature, were influenced by relative topography, including local topography and slope. Vineyards with flat slopes that had low elevations relative to their surroundings had larger diurnal variations and lower maximum and minimum temperatures than vineyards with steeper slopes that were high relative to their surroundings.

Processing precious metals in a top-blown rotary converter

NASA Astrophysics Data System (ADS)

Whellock, John G.; Matousek, Jan W.

1990-09-01

Copper-nickel/platinum-palladium flotation concentrates produced by the Stillwater Mining Company were smelted and refined in an integrated pilot plant consisting of a submerged-arc electric furnace and top-blown rotary converter. The conversion of high-iron electric furnace mattes was achieved with apparent oxygen efficiencies in excess of 100 percent. Platinum and palladium recoveries averaged 99 percent, and copper and nickel recoveries were 94 percent.

JPRS Report, China

DTIC Science & Technology

1989-05-17

expand. 2. Themain U.S. industrial sector—manufacturing—has been reviving in recent years. Afterthe economic crisis of the early 1980’s, the U.S...manufacturing sector began to recover. The average annual growth rate of labor produc- tivity in the U.S. manufacturing industry was slower than that of...expected to rise to 18 percent in 1989. Whether high-technology or traditional industries , both labor productivity and com- petitiveness of the U.S

Nucleation of Crystals From Solution in Microgravity (USML-1 Glovebox (GBX) Investigation)

NASA Technical Reports Server (NTRS)

Kroes, Roger L.; Reiss, Donald A.; Lehoczky, Sandor L.

1994-01-01

A new method for initiating nucleation from solutions in microgravity which avoids nucleation on container walls and other surfaces is described. This method consists of injecting a small quantity of highly concentrated, heated solution into the interior of a lightly supersaturated, cooler host gowth solution. It was tested successfully on USML-I, producing a large number of LAP crystals whose longest dimension averaged 1 mm.

Sediment losses and gains across a gradient of livestock grazing and plant invasion in a cool, semi-arid grassland, Colorado Plateau, USA

USGS Publications Warehouse

Belnap, J.; Reynolds, R.L.; Reheis, M.C.; Phillips, S.L.; Urban, F.E.; Goldstein, H.L.

2009-01-01

Large sediment fluxes can have significant impacts on ecosystems. We measured incoming and outgoing sediment across a gradient of soil disturbance (livestock grazing, plowing) and annual plant invasion for 9 years. Our sites included two currently ungrazed sites: one never grazed by livestock and dominated by perennial grasses/well-developed biocrusts and one not grazed since 1974 and dominated by annual weeds with little biocrusts. We used two currently grazed sites: one dominated by annual weeds and the other dominated by perennial plants, both with little biocrusts. Precipitation was highly variable, with years of average, above-average, and extremely low precipitation. During years with average and above-average precipitation, the disturbed sites consistently produced 2.8 times more sediment than the currently undisturbed sites. The never grazed site always produced the least sediment of all the sites. During the drought years, we observed a 5600-fold increase in sediment production from the most disturbed site (dominated by annual grasses, plowed about 50 years previously and currently grazed by livestock) relative to the never grazed site dominated by perennial grasses and well-developed biocrusts, indicating a non-linear, synergistic response to increasing disturbance types and levels. Comparing sediment losses among the sites, biocrusts were most important in predicting site stability, followed by perennial plant cover. Incoming sediment was similar among the sites, and while inputs were up to 9-fold higher at the most heavily disturbed site during drought years compared to average years, the change during the drought conditions was small relative to the large change seen in the sediment outputs. ?? 2009 Elsevier B.V. All rights reserved.

Religious burning as a potential major source of atmospheric fine aerosols in summertime Lhasa on the Tibetan Plateau

NASA Astrophysics Data System (ADS)

Cui, Yu Yan; Liu, Shang; Bai, Zhixuan; Bian, Jianchun; Li, Dan; Fan, Kaiyu; McKeen, Stuart A.; Watts, Laurel A.; Ciciora, Steven J.; Gao, Ru-Shan

2018-05-01

We carried out field measurements of aerosols in Lhasa, a major city in the Tibetan Plateau that has been experiencing fast urbanization and industrialization. Aerosol number size distribution was continuously measured using an optical particle size spectrometer near the center of Lhasa city during the Asian summer monsoon season in 2016. The mass concentration of fine particles was modulated by boundary layer dynamics, with an average of 11 μg m-3 and the high values exceeding 50 μg m-3 during religious holidays. Daytime high concentration coincided with the religious burning of biomass and incense in the temples during morning hours, which produced heavy smoke. Factor analysis revealed a factor that likely represented religious burning. The factor contributed 34% of the campaign-average fine particle mass and the contribution reached up to 80% during religious holidays. The mass size distribution of aerosols produced from religious burnings peaked at ∼500 nm, indicating that these particles could efficiently decrease visibility and promote health risk. Because of its significance, our results suggest that further studies of religious burning, a currently under-studied source, are needed in the Tibetan Plateau and in other regions of the world where religious burnings are frequently practiced.

Nitrogen dioxide exposures inside ice skating rinks.

PubMed Central

Brauer, M; Spengler, J D

1994-01-01

OBJECTIVES. The common operation of fuel-powered resurfacing equipment in enclosed ice skating rinks has the potential for producing high concentrations of carbon monoxide and nitrogen dioxide. Exposures to these gaseous combustion products may adversely affect the health of those inside the rink. Little information is available on pollutant concentrations under normal operating conditions. METHODS. One-week average nitrogen dioxide concentrations in 70 northeastern US rinks were measured with passive samplers during normal winter season conditions. RESULTS. The median nitrogen dioxide level inside rinks was 180 ppb, more than 10 times higher than the median outdoor concentration. One-week average nitrogen dioxide concentrations above 1000 ppb were measured in 10% of the rinks. CONCLUSIONS. Considering that short-term peak concentrations were likely to have reached two to five times the measured 1-week averages, our results suggest that nitrogen dioxide levels were well above short-term air quality guidelines and constitute a public health concern of considerable magnitude. PMID:8129060

Contact lens-induced circumlimbal staining in silicone hydrogel contact lenses worn on a daily wear basis.

PubMed

Maïssa, Cécile; Guillon, Michel; Garofalo, Renee J

2012-01-01

The principal objective of the study was to measure the conjunctival staining produced in the circumlimbal region by silicone hydrogel contact lenses with different edge designs. The secondary objective was to investigate the association between circumlimbal staining and comfort. Four silicone hydrogel contact lenses: ACUVUE OASYS (knife edge design), AIR OPTIX, Biofinity (chisel edge rounded edge combination), and PureVision (rounded edge design), and 1 hydrogel contact lens, ACUVUE 2 (knife edge design), were tested. The study was conducted on a cohort population of 27 established soft contact lens wearers, who wore each contact lens type, in a random order, for a period of 10 (±2) days. Circumlimbal staining was measured in a double-masked fashion through image analysis of digital photographs of lissamine green taken under controlled experimental conditions. The results obtained showed that contact lens edge design was the primary factor controlling circumlimbal staining for silicone hydrogel lenses: a rounded edge away from the ocular surface produced the lowest staining (average, 0.19%) and a knife edge in close apposition to the ocular surface produced the highest staining (average, 1.34%). Contact lens material rigidity was also identified to affect circumlimbal staining and an inverse association between circumlimbal staining and contact lens comfort was demonstrated: the rounded edge design produced the lowest comfort (72 of 100) and the knife edge design produced the highest (87 out of 100). Soft contact lens wear induces circumlimbal staining, the level of staining being influenced by the contact lens edge design. However, high level of circumlimbal staining is not associated with decreased comfort.

Measurement of broiler litter production rates and nutrient content using recycled litter.

PubMed

Coufal, C D; Chavez, C; Niemeyer, P R; Carey, J B

2006-03-01

It is important for broiler producers to know litter production rates and litter nutrient content when developing nutrient management plans. Estimation of broiler litter production varies widely in the literature due to factors such as geographical region, type of housing, size of broiler produced, and number of flocks reared on the same litter. Published data for N, P, and K content are also highly variable. In addition, few data are available regarding the rate of production, characteristics, and nutrient content of caked litter (cake). In this study, 18 consecutive flocks of broilers were reared on the same litter in experimental pens under simulated commercial conditions. The mass of litter and cake produced was measured after each flock. Samples of all litter materials were analyzed for pH, moisture, N, P, and K. Average litter and cake moisture content were 26.4 and 46.9%, respectively. Significant variation in litter and cake nutrient content was observed and can largely be attributed to ambient temperature differences. Average litter, cake, and total litter (litter plus cake) production rates were 153.3, 74.8, and 228.2 g of dry litter material per kg of live broiler weight (g/kg) per flock, respectively. Significant variation in litter production rates among flocks was also observed. Cumulative litter, cake, and total litter production rates after 18 flocks were 170.3, 78.7, and 249.0 g/kg, respectively. The data produced from this research can be used by broiler producers to estimate broiler litter and cake production and the nutrient content of these materials.

Cuprous Oxide Scale up: Gram Production via Bulk Synthesis using Classic Solvents at Low Temperatures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hall, A.; Han, T. Y.

Cuprous oxide is a p-type semiconducting material that has been highly researched for its interesting properties. Many small-scale syntheses have exhibited excellent control over size and morphology. As the demand for cuprous oxide grows, the synthesis method need to evolve to facilitate large-scale production. This paper supplies a facile bulk synthesis method for Cu₂O on average, 1-liter reaction volume can produce 1 gram of particles. In order to study the shape and size control mechanisms on such a scale, the reaction volume was diminished to 250 mL producing on average 0.3 grams of nanoparticles per batch. Well-shaped nanoparticles have beenmore » synthesized using an aqueous solution of CuCl₂, NaOH, SDS surfactant, and NH₂OH-HCl at mild temperatures. The time allotted between the addition of NaOH and NH₂OH-HCl was determined to be critical for Cu(OH)2 production, an important precursor to the final produce The effects of stirring rates on a large scale was also analyzed during reagent addition and post reagent addition. A morphological change from rhombic dodecahedra to spheres occurred as the stirring speed was increased. The effects of NH₂OH-HCl concentration were also studied to control the etching effects of the final product.« less

Process for producing silicon nitride based articles of high fracture toughness and strength

DOEpatents

Huckabee, Marvin; Buljan, Sergej-Tomislav; Neil, Jeffrey T.

1991-01-01

A process for producing a silicon nitride-based article of improved fracture toughness and strength. The process involves densifying to at least 98% of theoretical density a mixture including (a) a bimodal silicon nitride powder blend consisting essentially of about 10-30% by weight of a first silicon nitride powder of an average particle size of about 0.2 .mu.m and a surface area of about 8-12 m.sup.2 /g, and about 70-90% by weight of a second silicon nitride powder of an average particle size of about 0.4-0.6 .mu.m and a surface area of about 2-4 m.sup.2 /g, (b) about 10-50 percent by volume, based on the volume of the densified article, of refractory whiskers or fibers having an aspect ratio of about 3-150 and having an equivalent diameter selected to produce in the densified article an equivalent diameter ratio of the whiskers or fibers to grains of silicon nitride of greater than 1.0, and (c) an effective amount of a suitable oxide densification aid. Optionally, the mixture may be blended with a binder and injection molded to form a green body, which then may be densified by, for example, hot isostatic pressing.

Process for producing silicon nitride based articles of high fracture toughness and strength

DOEpatents

Huckabee, M.; Buljan, S.T.; Neil, J.T.

1991-09-10

A process for producing a silicon nitride-based article of improved fracture toughness and strength is disclosed. The process involves densifying to at least 98% of theoretical density a mixture including (a) a bimodal silicon nitride powder blend consisting essentially of about 10-30% by weight of a first silicon nitride powder of an average particle size of about 0.2 [mu]m and a surface area of about 8-12 m[sup 2]/g, and about 70-90% by weight of a second silicon nitride powder of an average particle size of about 0.4-0.6 [mu]m and a surface area of about 2-4 m[sup 2]/g, (b) about 10-50 percent by volume, based on the volume of the densified article, of refractory whiskers or fibers having an aspect ratio of about 3-150 and having an equivalent diameter selected to produce in the densified article an equivalent diameter ratio of the whiskers or fibers to grains of silicon nitride of greater than 1.0, and (c) an effective amount of a suitable oxide densification aid. Optionally, the mixture may be blended with a binder and injection molded to form a green body, which then may be densified by, for example, hot isostatic pressing.

Power mixture and green body for producing silicon nitride base articles of high fracture toughness and strength

DOEpatents

Huckabee, M.L.; Buljan, S.T.; Neil, J.T.

1991-09-17

A powder mixture and a green body for producing a silicon nitride-based article of improved fracture toughness and strength are disclosed. The powder mixture includes (a) a bimodal silicon nitride powder blend consisting essentially of about 10-30% by weight of a first silicon nitride powder of an average particle size of about 0.2 [mu]m and a surface area of about 8-12m[sup 2]g, and about 70-90% by weight of a second silicon nitride powder of an average particle size of about 0.4-0.6 [mu]m and a surface area of about 2-4 m[sup 2]/g, (b) about 10-50 percent by volume, based on the volume of the densified article, of refractory whiskers or fibers having an aspect ratio of about 3-150 and having an equivalent diameter selected to produce in the densified article an equivalent diameter ratio of the whiskers or fibers to grains of silicon nitride of greater than 1.0, and (c) an effective amount of a suitable oxide densification aid. The green body is formed from the powder mixture, an effective amount of a suitable oxide densification aid, and an effective amount of a suitable organic binder. No Drawings

Power mixture and green body for producing silicon nitride base & articles of high fracture toughness and strength

DOEpatents

Huckabee, Marvin L.; Buljan, Sergej-Tomislav; Neil, Jeffrey T.

1991-01-01

A powder mixture and a green body for producing a silicon nitride-based article of improved fracture toughness and strength. The powder mixture includes 9a) a bimodal silicon nitride powder blend consisting essentially of about 10-30% by weight of a first silicon mitride powder of an average particle size of about 0.2 .mu.m and a surface area of about 8-12m.sup.2 g, and about 70-90% by weight of a second silicon nitride powder of an average particle size of about 0.4-0.6 .mu.m and a surface area of about 2-4 m.sup.2 /g, (b) about 10-50 percent by volume, based on the volume of the densified article, of refractory whiskers or fibers having an aspect ratio of about 3-150 and having an equivalent diameter selected to produce in the densified articel an equivalent diameter ratio of the whiskers or fibers to grains of silicon nitride of greater than 1.0, and (c) an effective amount of a suitable oxide densification aid. The green body is formed from the powder mixture, an effective amount of a suitable oxide densification aid, and an effective amount of a suitable organic binder.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirhan, S.; Inaner, H.; Nakoman, E.

This study focuses on some lignite properties and calculation of lignite reserves with two classical (isopach and polygon) methods in the Aydin-Sahinali field, Turkey, which is located in the western Turkey. This field has been mined by a private coal company since 1960 by open-cast and mainly underground mining methods. The producing lignites are consumed in domestic heating and industrial factories around Aydin. The metamorphic rocks of Palaezoic age form the basement of the coal field. The lignite-bearing unit of Miocene age, from bottom to the top, consists mainly of pebblestone, lignite and clayey lignite, siltstone with sandstone lenses, whitemore » colored claystone, clayey limestone and silisified limestone lenses. This unit in the lignite field was unconformably overlain by Pliocene unconsolidated sands and gravels. Three hundred seventy-three borehole data have been evaluated, and this study shows that a relatively thick and lateral extensive lignite seam has a mineable thickness of 1.6-14.4 m. The core samples from boreholes in panels in the lignite field indicate that the coal seam, on an as-received basis, contains high moisture contents (17.95-23.45%, average), high ash yields (16.30-26.03%, average), relatively high net calorific values (3,281-3,854 kcal/kg, average), and low total sulfur contents (1.00-1.22%, average). The remaining lignite potential in the Aydin-Sahinali lignite field was calculated as a 4.7 Mt of measured and a 2.9 Mt of mineable lignite-reserves.« less

Heat flow and hydrocarbon generation in the Transylvanian basin, Romania

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cranganu, C.; Deming, D.

1996-10-01

The Transylvanian basin in central Romania is a Neogene depression superimposed on the Cretaceous nappe system of the Carpathian Mountains. The basin contains the main gas reserves of Romania, and is one of the most important gas-producing areas of continental Europe; since 1902, gas has been produced from more than 60 fields. Surface heat flow in the Transylvanian basin as estimated in other studies ranges from 26 to 58 mW/m{sup 2}, with a mean value of 38 mW/m{sup 2}, relatively low compared to surrounding areas. The effect of sedimentation on heat flow and temperature in the Transylvanian basin was estimatedmore » with a numerical model that solved the heat equation in one dimension. Because both sediment thickness and heat flow vary widely throughout the Transylvanian basin, a wide range of model variables were used to bracket the range of possibilities. Three different burial histories were considered (thin, average, and thick), along with three different values of background heat flow (low, average, and high). Altogether, nine different model permutations were studied. Modeling results show that average heat flow in the Transylvanian basin was depressed approximately 16% during rapid Miocene sedimentation, whereas present-day heat flow remains depressed, on average, about 17% below equilibrium values. We estimated source rock maturation and the timing of hydrocarbon generation by applying Lopatin`s method. Potential source rocks in the Transylvanian basin are Oligocene-Miocene, Cretaceous, and Jurassic black shales. Results show that potential source rocks entered the oil window no earlier than approximately 13 Ma, at depths of between 4200 and 8800 m. Most simulations encompassing a realistic range of sediment thicknesses and background heat flows show that potential source rocks presently are in the oil window; however, no oil has ever been discovered or produced in the Transylvanian basin.« less

Noise reduction in single time frame optical DNA maps

PubMed Central

Müller, Vilhelm; Westerlund, Fredrik

2017-01-01

In optical DNA mapping technologies sequence-specific intensity variations (DNA barcodes) along stretched and stained DNA molecules are produced. These “fingerprints” of the underlying DNA sequence have a resolution of the order one kilobasepairs and the stretching of the DNA molecules are performed by surface adsorption or nano-channel setups. A post-processing challenge for nano-channel based methods, due to local and global random movement of the DNA molecule during imaging, is how to align different time frames in order to produce reproducible time-averaged DNA barcodes. The current solutions to this challenge are computationally rather slow. With high-throughput applications in mind, we here introduce a parameter-free method for filtering a single time frame noisy barcode (snap-shot optical map), measured in a fraction of a second. By using only a single time frame barcode we circumvent the need for post-processing alignment. We demonstrate that our method is successful at providing filtered barcodes which are less noisy and more similar to time averaged barcodes. The method is based on the application of a low-pass filter on a single noisy barcode using the width of the Point Spread Function of the system as a unique, and known, filtering parameter. We find that after applying our method, the Pearson correlation coefficient (a real number in the range from -1 to 1) between the single time-frame barcode and the time average of the aligned kymograph increases significantly, roughly by 0.2 on average. By comparing to a database of more than 3000 theoretical plasmid barcodes we show that the capabilities to identify plasmids is improved by filtering single time-frame barcodes compared to the unfiltered analogues. Since snap-shot experiments and computational time using our method both are less than a second, this study opens up for high throughput optical DNA mapping with improved reproducibility. PMID:28640821

Production of polycaprolactone nanoparticles with low polydispersity index in a tubular recirculating system by using a multifactorial design of experiments

NASA Astrophysics Data System (ADS)

Colmenares Roldán, Gabriel Jaime; Agudelo Gomez, Liliana María; Carlos Cornelio, Jesús Antonio; Rodriguez, Luis Fernando; Pinal, Rodolfo; Hoyos Palacio, Lina Marcela

2018-03-01

Encapsulation and controlled release of substances using polymeric nanoparticles require that these have a high reproducibility, homogeneity, and control over their properties (diameter and polydispersity), especially when they are to be used in medical, pharmaceutical, or nutritional applications among others. In conventional production systems, it is tough to ensure these characteristics; hence, the cost increases when we try to control these properties. This paper shows a comparison between a recirculating system and the standard nanoprecipitation technique for producing polymeric nanoparticles. In previous investigations, we evaluate the effect of recirculating flow and the ratio between the organic and aqueous phase. For this paper, we evaluated the effect of polymer and surfactant concentrations using a multifactorial design of experiments on the recirculating system and on the standard nanoprecipitation system. The response of the design was the average diameter of the nanoparticles and polydispersity index. Finally, we found that the polymer and surfactant concentrations could change the average diameter and polydispersity index of the nanoparticles obtained. On the other hand, it was found that the effect of the polymer concentration was stronger than the surfactant concentration to reduce the average diameter of the nanoparticles. The results of the present study show that the proposed recirculation system presents a high potential to produce polymer nanoparticles with good morphological characteristics, particle size distributions in the nano range, and with a low polydispersity. The average mean size of nanoparticles of polycaprolactone for the design using the recirculating system was of 61 to 140 nm and the values of polydispersity index PDI for this design were between 0.097 and 0.22, while for the design using the standard nanoprecipitation technique, the obtained diameters were 74 to 176 nm and the polydispersity was between 0.26 and 0.41.

Bootstrap-after-bootstrap model averaging for reducing model uncertainty in model selection for air pollution mortality studies.

PubMed

Roberts, Steven; Martin, Michael A

2010-01-01

Concerns have been raised about findings of associations between particulate matter (PM) air pollution and mortality that have been based on a single "best" model arising from a model selection procedure, because such a strategy may ignore model uncertainty inherently involved in searching through a set of candidate models to find the best model. Model averaging has been proposed as a method of allowing for model uncertainty in this context. To propose an extension (double BOOT) to a previously described bootstrap model-averaging procedure (BOOT) for use in time series studies of the association between PM and mortality. We compared double BOOT and BOOT with Bayesian model averaging (BMA) and a standard method of model selection [standard Akaike's information criterion (AIC)]. Actual time series data from the United States are used to conduct a simulation study to compare and contrast the performance of double BOOT, BOOT, BMA, and standard AIC. Double BOOT produced estimates of the effect of PM on mortality that have had smaller root mean squared error than did those produced by BOOT, BMA, and standard AIC. This performance boost resulted from estimates produced by double BOOT having smaller variance than those produced by BOOT and BMA. Double BOOT is a viable alternative to BOOT and BMA for producing estimates of the mortality effect of PM.

Relations between precipitation, groundwater withdrawals, and changes in hydrologic conditions at selected monitoring sites in Volusia County, Florida, 1995--2010

USGS Publications Warehouse

Murray, Louis C.

2012-01-01

A study to examine the influences of climatic and anthropogenic stressors on groundwater levels, lake stages, and surface-water discharge at selected sites in northern Volusia County, Florida, was conducted in 2009 by the U.S. Geological Survey. Water-level data collected at 20 monitoring sites (17 groundwater and 3 lake sites) in the vicinity of a wetland area were analyzed with multiple linear regression to examine the relative influences of precipitation and groundwater withdrawals on changes in groundwater levels and lake stage. Analyses were conducted across varying periods of record between 1995 and 2010 and included the effects of groundwater withdrawals aggregated from municipal water-supply wells located within 12 miles of the project sites. Surface-water discharge data at the U.S. Geological Survey Tiger Bay canal site were analyzed for changes in flow between 1978 and 2001. As expected, water-level changes in monitoring wells located closer to areas of concentrated groundwater withdrawals were more highly correlated with withdrawals than were water-level changes measured in wells further removed from municipal well fields. Similarly, water-level changes in wells tapping the Upper Floridan aquifer, the source of municipal supply, were more highly correlated with groundwater withdrawals than were water-level changes in wells tapping the shallower surficial aquifer system. Water-level changes predicted by the regression models over precipitation-averaged periods of record were underestimated for observations having large positive monthly changes (generally greater than 1.0 foot). Such observations are associated with high precipitation and were identified as points in the regression analyses that produced large standardized residuals and/or observations of high influence. Thus, regression models produced by multiple linear regression analyses may have better predictive capability in wetland environments when applied to periods of average or below average precipitation conditions than during wetter than average conditions. For precipitation-averaged hydrologic conditions, water-level changes in the surficial aquifer system were statistically correlated solely with precipitation or were more highly correlated with precipitation than with groundwater withdrawals. Changes in Upper Floridan aquifer water levels and in water-surface stage (stage) at Indian and Scoggin Lakes tended to be highly correlated with both precipitation and withdrawals. The greater influence of withdrawals on stage changes, relative to changes in nearby surficial aquifer system water levels, indicates that these karstic lakes may be better connected hydraulically with the underlying Upper Floridan aquifer than is the surficial aquifer system at the other monitoring sites. At most sites, and for both aquifers, the 2-month moving average of precipitation or groundwater withdrawals included as an explanatory variable in the regression models indicates that water-level changes are not only influenced by stressor conditions across the current month, but also by those of the previous month. The relations between changes in water levels, precipitation, and groundwater withdrawals varied seasonally and in response to a period of drought. Water-level changes tended to be most highly correlated with withdrawals during the spring, when relatively large increases contributed to water-level declines, and during the fall when reduced withdrawal rates contributed to water-level recovery. Water-level changes tended to be most highly (or solely) correlated with precipitation in the winter, when withdrawals are minimal, and in the summer when precipitation is greatest. Water-level changes measured during the drought of October 2005 to June 2008 tended to be more highly correlated with groundwater withdrawals at Upper Floridan aquifer sites than at surficial aquifer system sites, results that were similar to those for precipitation-averaged conditions. Also, changes in stage at Indian and Scoggin Lakes were highly correlated with precipitation and groundwater withdrawals during the drought. Groundwater-withdrawal rates during the drought were, on average, greater than those for precipitation-averaged conditions. Accounting only for withdrawals aggregated from pumping wells located within varying radial distances of less than 12 miles of each site produced essentially the same relation between water-level changes and groundwater withdrawals as that determined for withdrawals aggregated within 12 miles of the site. Similarly, increases in withdrawals aggregated over distances of 1 to 12 miles of the sites had little effect on adjusted R-squared values. Analyses of streamflow measurements collected between 1978 and 2001 at the U.S. Geological Survey Tiger Bay canal site indicate that significant changes occurred during base-flow conditions during that period. Hypothesis and trend testing, together with analyses of flow duration, the number of zero-flow days, and double-mass curves indicate that, after 1988, when a municipal well field began production, base flow was statistically lower than the period before 1988. This decrease in base flow could not be explained by variations in precipitation between these two periods.

Industrial applications of high-average power high-peak power nanosecond pulse duration Nd:YAG lasers

NASA Astrophysics Data System (ADS)

Harrison, Paul M.; Ellwi, Samir

2009-02-01

Within the vast range of laser materials processing applications, every type of successful commercial laser has been driven by a major industrial process. For high average power, high peak power, nanosecond pulse duration Nd:YAG DPSS lasers, the enabling process is high speed surface engineering. This includes applications such as thin film patterning and selective coating removal in markets such as the flat panel displays (FPD), solar and automotive industries. Applications such as these tend to require working spots that have uniform intensity distribution using specific shapes and dimensions, so a range of innovative beam delivery systems have been developed that convert the gaussian beam shape produced by the laser into a range of rectangular and/or shaped spots, as required by demands of each project. In this paper the authors will discuss the key parameters of this type of laser and examine why they are important for high speed surface engineering projects, and how they affect the underlying laser-material interaction and the removal mechanism. Several case studies will be considered in the FPD and solar markets, exploring the close link between the application, the key laser characteristics and the beam delivery system that link these together.

Comparative genomics of citric-acid-producing Aspergillus niger ATCC 1015 versus enzyme-producing CBS 513.88

PubMed Central

Andersen, Mikael R.; Salazar, Margarita P.; Schaap, Peter J.; van de Vondervoort, Peter J.I.; Culley, David; Thykaer, Jette; Frisvad, Jens C.; Nielsen, Kristian F.; Albang, Richard; Albermann, Kaj; Berka, Randy M.; Braus, Gerhard H.; Braus-Stromeyer, Susanna A.; Corrochano, Luis M.; Dai, Ziyu; van Dijck, Piet W.M.; Hofmann, Gerald; Lasure, Linda L.; Magnuson, Jon K.; Menke, Hildegard; Meijer, Martin; Meijer, Susan L.; Nielsen, Jakob B.; Nielsen, Michael L.; van Ooyen, Albert J.J.; Pel, Herman J.; Poulsen, Lars; Samson, Rob A.; Stam, Hein; Tsang, Adrian; van den Brink, Johannes M.; Atkins, Alex; Aerts, Andrea; Shapiro, Harris; Pangilinan, Jasmyn; Salamov, Asaf; Lou, Yigong; Lindquist, Erika; Lucas, Susan; Grimwood, Jane; Grigoriev, Igor V.; Kubicek, Christian P.; Martinez, Diego; van Peij, Noël N.M.E.; Roubos, Johannes A.; Nielsen, Jens; Baker, Scott E.

2011-01-01

The filamentous fungus Aspergillus niger exhibits great diversity in its phenotype. It is found globally, both as marine and terrestrial strains, produces both organic acids and hydrolytic enzymes in high amounts, and some isolates exhibit pathogenicity. Although the genome of an industrial enzyme-producing A. niger strain (CBS 513.88) has already been sequenced, the versatility and diversity of this species compel additional exploration. We therefore undertook whole-genome sequencing of the acidogenic A. niger wild-type strain (ATCC 1015) and produced a genome sequence of very high quality. Only 15 gaps are present in the sequence, and half the telomeric regions have been elucidated. Moreover, sequence information from ATCC 1015 was used to improve the genome sequence of CBS 513.88. Chromosome-level comparisons uncovered several genome rearrangements, deletions, a clear case of strain-specific horizontal gene transfer, and identification of 0.8 Mb of novel sequence. Single nucleotide polymorphisms per kilobase (SNPs/kb) between the two strains were found to be exceptionally high (average: 7.8, maximum: 160 SNPs/kb). High variation within the species was confirmed with exo-metabolite profiling and phylogenetics. Detailed lists of alleles were generated, and genotypic differences were observed to accumulate in metabolic pathways essential to acid production and protein synthesis. A transcriptome analysis supported up-regulation of genes associated with biosynthesis of amino acids that are abundant in glucoamylase A, tRNA-synthases, and protein transporters in the protein producing CBS 513.88 strain. Our results and data sets from this integrative systems biology analysis resulted in a snapshot of fungal evolution and will support further optimization of cell factories based on filamentous fungi. PMID:21543515

[Characterization of microbial community in produced water from a petroleum reservoir subjected to alkali-surfactant-polymer ASP flooding].

PubMed

Hao, Qin Qin; Shi, Rong Jiu; Hao, Jin Sheng; Zhao, Jin Yi; Li, Guo Qiao; Zhao, Feng; Han, Si Qin; Zhang, Ying

2017-10-01

Injection of alkali, surfactant and polymer (ASP) into oil reservoir can substantially increase oil recovery compared with water-flooding strategy. However, the effects of these agents on the microbial diversity and community structure, which is important for water management and corrosion control in oil industry, are hitherto poorly understood. Here, we disclosed the microbial diversity and community structure in the produced water collected from four producing wells of an ASP-flooded oilfield at Daqing, China, using high-throughput sequencing technique. Results showed that the average pH in produced water was as high as 9.65. The microbial diversity varied from well to well, and the Shannon diversity index was between 2.00 to 3.56. The Proteobacteria (85.5%-98.3%), γ-proteobacteria (83.7%-97.8%), and alkaliphilic Nitrincola (51.8%-82.5%) were the most dominant phylogenetic taxa at the phylum, class, and genus levels, respectively. A total of 12 potentially sulfide-producing genera were detected, and the most abundant taxon was Sulfurospirillum (0.4%-7.4%). The microbial community of ASP-flooded petroleum reservoir was distinct, showing an alkaliphilic or alkalitolerant potential; a reduced diversity and more simple structure were observed compared with those of the water-flooded petroleum reservoirs that were previously reported.

Vocal fold vibration and voice source aperiodicity in 'dist' tones: a study of a timbral ornament in rock singing.

PubMed

Borch, D Zangger; Sundberg, J; Lindestad, P A; Thalén, M

2004-01-01

The acoustic characteristics of so-called 'dist' tones, commonly used in singing rock music, are analyzed in a case study. In an initial experiment a professional rock singer produced examples of 'dist' tones. The tones were found to contain aperiodicity, SPL at 0.3 m varied between 90 and 96 dB, and subglottal pressure varied in the range of 20-43 cm H2O, a doubling yielding, on average, an SPL increase of 2.3 dB. In a second experiment, the associated vocal fold vibration patterns were recorded by digital high-speed imaging of the same singer. Inverse filtering of the simultaneously recorded audio signal showed that the aperiodicity was caused by a low frequency modulation of the flow glottogram pulse amplitude. This modulation was produced by an aperiodic or periodic vibration of the supraglottic mucosa. This vibration reduced the pulse amplitude by obstructing the airway for some of the pulses produced by the apparently periodically vibrating vocal folds. The supraglottic mucosa vibration can be assumed to be driven by the high airflow produced by the elevated subglottal pressure.

Comparative genomics of citric-acid producing Aspergillus niger ATCC 1015 versus enzyme-producing CBS 513.88

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andersen, Mikael R.; Salazar, Margarita; Schaap, Peter

2011-06-01

The filamentous fungus Aspergillus niger exhibits great diversity in its phenotype. It is found globally, both as marine and terrestrial strains, produces both organic acids and hydrolytic enzymes in high amounts, and some isolates exhibit pathogenicity. Although the genome of an industrial enzyme-producing A. niger strain (CBS 513.88) has already been sequenced, the versatility and diversity of this species compels additional exploration. We therefore undertook whole genome sequencing of the acidogenic A. niger wild type strain (ATCC 1015), and produced a genome sequence of very high quality. Only 15 gaps are present in the sequence and half the telomeric regionsmore » have been elucidated. Moreover, sequence information from ATCC 1015 was utilized to improve the genome sequence of CBS 513.88. Chromosome-level comparisons uncovered several genome rearrangements, deletions, a clear case of strain-specific horizontal gene transfer, and identification of 0.8 megabase of novel sequence. Single nucleotide polymorphisms per kilobase (SNPs/kb) between the two strains were found to be exceptionally high (average: 7.8, maximum: 160 SNPs/kb). High variation within the species was confirmed with exo-metabolite profiling and phylogenetics. Detailed lists of alleles were generated, and genotypic differences were observed to accumulate in metabolic pathways essential to acid production and protein synthesis. A transcriptome analysis revealed up-regulation of the electron transport chain, specifically the alternative oxidative pathway in ATCC 1015, while CBS 513.88 showed significant up regulation of genes associated with biosynthesis of amino acids that are abundant in glucoamylase A, tRNA-synthases and protein transporters.« less

Cooperation prevails when individuals adjust their social ties.

PubMed

Santos, Francisco C; Pacheco, Jorge M; Lenaerts, Tom

2006-10-20

Conventional evolutionary game theory predicts that natural selection favours the selfish and strong even though cooperative interactions thrive at all levels of organization in living systems. Recent investigations demonstrated that a limiting factor for the evolution of cooperative interactions is the way in which they are organized, cooperators becoming evolutionarily competitive whenever individuals are constrained to interact with few others along the edges of networks with low average connectivity. Despite this insight, the conundrum of cooperation remains since recent empirical data shows that real networks exhibit typically high average connectivity and associated single-to-broad-scale heterogeneity. Here, a computational model is constructed in which individuals are able to self-organize both their strategy and their social ties throughout evolution, based exclusively on their self-interest. We show that the entangled evolution of individual strategy and network structure constitutes a key mechanism for the sustainability of cooperation in social networks. For a given average connectivity of the population, there is a critical value for the ratio W between the time scales associated with the evolution of strategy and of structure above which cooperators wipe out defectors. Moreover, the emerging social networks exhibit an overall heterogeneity that accounts very well for the diversity of patterns recently found in acquired data on social networks. Finally, heterogeneity is found to become maximal when W reaches its critical value. These results show that simple topological dynamics reflecting the individual capacity for self-organization of social ties can produce realistic networks of high average connectivity with associated single-to-broad-scale heterogeneity. On the other hand, they show that cooperation cannot evolve as a result of "social viscosity" alone in heterogeneous networks with high average connectivity, requiring the additional mechanism of topological co-evolution to ensure the survival of cooperative behaviour.

Toward graduate medical education (GME) accountability: measuring the outcomes of GME institutions.

PubMed

Chen, Candice; Petterson, Stephen; Phillips, Robert L; Mullan, Fitzhugh; Bazemore, Andrew; O'Donnell, Sarah D

2013-09-01

Graduate medical education (GME) plays a key role in the U.S. health care workforce, defining its overall size and specialty distribution and influencing physician practice locations. Medicare provides nearly $10 billion annually to support GME and faces growing policy maker interest in creating accountability measures. The purpose of this study was to develop and test candidate GME outcome measures related to physician workforce. The authors performed a secondary analysis of data from the American Medical Association Physician Masterfile, National Provider Identifier file, Medicare claims, and National Health Service Corps, measuring the number and percentage of graduates from 2006 to 2008 practicing in high-need specialties and underserved areas aggregated by their U.S. GME program. Average overall primary care production rate was 25.2% for the study period, although this is an overestimate because hospitalists could not be excluded. Of 759 sponsoring institutions, 158 produced no primary care graduates, and 184 produced more than 80%. An average of 37.9% of internal medicine residents were retained in primary care, including hospitalists. Mean general surgery retention was 38.4%. Overall, 4.8% of graduates practiced in rural areas; 198 institutions produced no rural physicians, and 283 institutions produced no Federally Qualified Health Center or Rural Health Clinic physicians. GME outcomes are measurable for most institutions and training sites. Specialty and geographic locations vary significantly. These findings can inform educators and policy makers during a period of increased calls to align the GME system with national health needs.

Numerical investigation of the relationship between magnetic stiffness and minor loop size in the HTS levitation system

NASA Astrophysics Data System (ADS)

Yang, Yong; Li, Chengshan

2017-10-01

The effect of minor loop size on the magnetic stiffness has not been paid attention to by most researchers in experimental and theoretical studies about the high temperature superconductor (HTS) magnetic levitation system. In this work, we numerically investigate the average magnetic stiffness obtained by the minor loop traverses Δz (or Δx) varying from 0.1 mm to 2 mm in zero field cooling and field cooling regimes, respectively. The approximate values of the magnetic stiffness with zero traverse are obtained using the method of linear extrapolation. Compared with the average magnetic stiffness gained by any minor loop traverse, these approximate values are Not always close to the average magnetic stiffness produced by the smallest size of minor loops. The relative deviation ranges of average magnetic stiffness gained by the usually minor loop traverse (1 or 2 mm) are presented by the ratios of approximate values to average stiffness for different moving processes and two typical cooling conditions. The results show that most of average magnetic stiffness are remarkably influenced by the sizes of minor loop, which indicates that the magnetic stiffness obtained by a single minor loop traverse Δ z or Δ x, for example, 1 or 2 mm, can be generally caused a large deviation.

An effectiveness trial of a new enhanced dissonance eating disorder prevention program among female college students.

PubMed

Stice, Eric; Butryn, Meghan L; Rohde, Paul; Shaw, Heather; Marti, C Nathan

2013-12-01

Efficacy trials indicate that a dissonance-based prevention program in which female high school and college students with body image concerns critique the thin-ideal reduced risk factors, eating disorder symptoms, and future eating disorder onset, but weaker effects emerged from an effectiveness trial wherein high school clinicians recruited students and delivered the program under real-world conditions. The present effectiveness trial tested whether a new enhanced dissonance version of this program produced larger effects when college clinicians recruited students and delivered the intervention using improved procedures to select, train, and supervise clinicians. Young women recruited from seven universities across the US (N = 408, M age = 21.6, SD = 5.64) were randomized to the dissonance intervention or an educational brochure control condition. Dissonance participants showed significantly greater decreases in risk factors (thin-ideal internalization, body dissatisfaction, dieting, negative affect) and eating disorder symptoms versus controls at posttest and 1-year follow-up, resulting in medium average effect size (d = .60). Dissonance participants also reported significant improvements in psychosocial functioning, but not reduced health care utilization or unhealthy weight gain. This novel multisite effectiveness trial with college clinicians found that the enhanced dissonance version of this program and the improved facilitator selection/training procedures produced average effects that were 83% larger than effects observed in the high school effectiveness trial. Copyright © 2013 Elsevier Ltd. All rights reserved.

Method and apparatus for altering material

DOEpatents

Stinnett, Regan W.; Greenly, John B.

2002-01-01

Methods and apparatus for thermally altering the near surface characteristics of a material are described. In particular, a repetitively pulsed ion beam system comprising a high energy pulsed power source and an ion beam generator are described which are capable of producing single species high voltage ion beams (0.25-2.5 MeV) at 1-1000 kW average power and over extended operating cycles (10.sup.8). Irradiating materials with such high energy, repetitively pulsed ion beams can yield surface treatments including localized high temperature anneals to melting, both followed by rapid thermal quenching to ambient temperatures to achieve both novel and heretofore commercially unachievable physical characteristics in a near surface layer of material.

Method and apparatus for altering material

DOEpatents

Stinnett, Regan W.; Greenly, John B.

1995-01-01

Methods and apparatus for thermally altering the near surface characteristics of a material are described. In particular, a repetitively pulsed ion beam system comprising a high energy pulsed power source and an ion beam generator are described which are capable of producing single species high voltage ion beams (0.25-2.5 MeV) at 1-1000 kW average power and over extended operating cycles (10.sup.8). Irradiating materials with such high energy, repetitively pulsed ion beams can yield surface treatments including localized high temperature anneals to melting, both followed by rapid thermal quenching to ambient temperatures to achieve both novel and heretofore commercially unachievable physical characteristics in a near surface layer of material.

Method and apparatus for altering material

DOEpatents

Stinnett, Regan W.; Greenly, John B.

2002-02-05

Methods and apparatus for thermally altering the near surface characteristics of a material are described. In particular, a repetitively pulsed ion beam system comprising a high energy pulsed power source and an ion beam generator are described which are capable of producing single species high voltage ion beams (0.25-2.5 MeV) at 1-1000 kW average power and over extended operating cycles (10.sup.8). Irradiating materials with such high energy, repetitively pulsed ion beams can yield surface treatments including localized high temperature anneals to melting, both followed by rapid thermal quenching to ambient temperatures to achieve both novel and heretofore commercially unachievable physical characteristics in a near surface layer of material.

Titanium Carbide Nanofibers-Reinforced Aluminum Compacts, a New Strategy to Enhance Mechanical Properties.

PubMed

Khalil, Khalil Abdelrazek; Sherif, El-Sayed M; Nabawy, A M; Abdo, Hany S; Marzouk, Wagih W; Alharbi, Hamad F

2016-05-20

TiC nanofibers reinforced Al matrix composites were produced by High Frequency Induction Heat Sintering (HFIHS).The titanium carbide nanofibers with an average diameter of 90 nm are first prepared by electrospinning technique and high temperature calcination process. A composite solution containing polyacrylonitrile and titanium isopropoxide is first electrospun into the nanofibers, which are subsequently stabilized and then calcined to produce the desired TiC nanofibers. The X-ray diffraction pattern and transmission electron microscopy results show that the main phase of the as-synthesized nanofibers is titanium carbide. The TiC nanofibers is then mixed with the aluminum powders and introduced into high frequency induction heat sintering (HFIHS) to produce composites of TiC nanofibers reinforced aluminum matrix. The potential application of the TiC nanofibers reinforced aluminum matrix composites was systematically investigated. 99.5% relative density and around 85 HV (833 MPa) Vickers hardness of the Al reinforced with 5 wt % TiC nanofiber has been obtained. Furthermore, the sample of Al contains 5 wt % TiC, has the highest value of compression and yield strength of about 415 and 350 MPa, respectively. The ductility of the Al/5 wt % TiC showed increasing with increasing the TiC contents.

Availability, quality and price of produce in low-income neighbourhood food stores in California raise equity issues.

PubMed

Gosliner, Wendi; Brown, Daniel M; Sun, Betty C; Woodward-Lopez, Gail; Crawford, Patricia B

2018-06-01

To assess produce availability, quality and price in a large sample of food stores in low-income neighbourhoods in California. Cross-sectional statewide survey. Between 2011 and 2015, local health departments assessed store type, WIC (Supplemental Nutrition Program for Women, Infants, and Children)/SNAP (Supplemental Nutrition Assistance Program) participation, produce availability, quality and price of selected items in stores in low-income neighbourhoods. Secondary data provided reference chain supermarket produce prices matched by county and month. t Tests and ANOVA examined differences by store type; regression models examined factors associated with price. Large grocery stores (n 231), small markets (n 621) and convenience stores (n 622) in 225 neighbourhoods. Produce in most large groceries was rated high quality (97 % of fruits, 98 % of vegetables), but not in convenience stores (25 % fruits, 14 % vegetables). Small markets and convenience stores participating in WIC and/or SNAP had better produce availability, variety and quality than non-participating stores. Produce prices across store types were, on average, higher than reference prices from matched chain supermarkets (27 % higher in large groceries, 37 % higher in small markets, 102 % higher in convenience stores). Price was significantly inversely associated with produce variety, adjusting for quality, store type, and SNAP and WIC participation. The study finds that fresh produce is more expensive in low-income neighbourhoods and that convenience stores offer more expensive, poorer-quality produce than other stores. Variety is associated with price and most limited in convenience stores, suggesting more work is needed to determine how convenience stores can provide low-income consumers with access to affordable, high-quality produce. WIC and SNAP can contribute to the solution.

Amino acid conversions by coagulase-negative staphylococci in a rich medium: Assessment of inter- and intraspecies heterogeneity.

PubMed

Stavropoulou, Despoina Angeliki; Borremans, Wim; De Vuyst, Luc; De Smet, Stefaan; Leroy, Frédéric

2015-11-06

The ability of coagulase-negative staphylococci (CNS) to convert amino acids into volatile compounds and biogenic amines was investigated after 24h and 48 h of incubation in a rich medium (brain heart infusion). Volatile compounds were measured with static-headspace gas chromatography and mass spectrometry (SH-GC-MS); biogenic amine measurements were carried out with a newly developed method based on ultra-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS). In total, 56 CNS strains from five different species were used, namely Staphylococcus carnosus, Staphylococcus epidermidis, Staphylococcus equorum, Staphylococcus saprophyticus, and Staphylococcus xylosus. With respect to the production of volatile compounds, the leucine-derived 3-methyl butanol was produced over time by most CNS strains, up to 52 μM for S. xylosus W1-1 after 48 h of incubation. The average production by strains of S. xylosus was significantly higher than for strains of S. carnosus, whereas strains of S. epidermidis turned out to be poor producers. Yet, differences between species were blurred to a large degree because of the high strain variability. A few strains also produced 3-methyl butanal on top of the amount that was already present in the medium background, although most CNS led to a decrease of this compound. Concerning biogenic amines, the average total concentrations per species remained below 100 μM after 48 h of incubation. The most abundant variant was 2-phenylethylamine (PEA), especially within S. carnosus (average of 65 μM after 48 h of incubation). Yet, some individual strains were able to produce higher concentrations, as found for the PEA production of 295 μM by S. epidermidis ATCC 12228 after 48 h of incubation. The insights obtained during this study indicate heterogeneity and are of importance in view of both starter culture development and the evaluation of a spontaneously established CNS microbiota in artisan-type meat fermentations. Copyright © 2015 Elsevier B.V. All rights reserved.

Cylinder-averaged histories of nitrogen oxide in a DI diesel with simulated turbocharging

NASA Astrophysics Data System (ADS)

Donahue, Ronald J.; Borman, Gary L.; Bower, Glenn R.

1994-10-01

An experimental study was conducted using the dumping technique (total cylinder sampling) to produce cylinder mass-averaged nitric oxide histories. Data were taken using a four stroke diesel research engine employing a quiescent chamber, high pressure direct injection fuel system, and simulated turbocharging. Two fuels were used to determine fuel cetane number effects. Two loads were run, one at an equivalence ratio of 0.5 and the other at a ratio of 0.3. The engine speed was held constant at 1500 rpm. Under the turbocharged and retarded timing conditions of this study, nitric oxide was produced up to the point of about 85% mass burned. Two different models were used to simulate the engine mn conditions: the phenomenological Hiroyasu spray-combustion model, and the three dimensional, U.W.-ERO modified KIVA-2 computational fluid dynamic code. Both of the models predicted the correct nitric oxide trend. Although the modified KIVA-2 combustion model using Zeldovich kinetics correctly predicted the shapes of the nitric oxide histories, it did not predict the exhaust concentrations without arbitrary adjustment based on experimental values.

Optimization of high molecular weight pullulan production by Aureobasidium pullulans in batch fermentations.

PubMed

Gibson, Larry H; Coughlin, Robert W

2002-01-01

Of five strains of Aureobasidium pullulans studied, NRRL Y-2311-1 yielded the highest titer (26.2 g/L) of pullulan and formed the lowest amount of melanin-like pigment. Sucrose was superior to glucose as the carbon and energy source on the basis of yield and titer of pullulan produced. Pullulan titer was higher (26.2 vs 5.1 g/L), biomass concentration was lower (6.9 vs 12.7 g/L), and DO was lower (0 vs 60% of saturation) when the fermenter was agitated by a marine propeller compared to Rushton impellers. Pullulan produced by strain NRRL Y-2311-1 ranged in weight-average molar mass (M(w)) from 486 KDa and number-average molar mass (M(n)) from 220 Da on day 1 of growth to 390 KDa and 690 Da on day 6; M(w) declined by about 35% from day 1 to day 3, the day of maximum pullulan titer. For the other strains, the ranges of molar mass on the day of maximum pullulan titer were 338-614 KDa (M(w)) and 100-6820 Da (M(n)).

Channeling Radiation Experiment at Fermilab ASTA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mihalcea, D.; Edstrom, D. R.; Piot, P.

2015-06-01

Electron beams with moderate energy ranging from 4 to 50 MeV can be used to produce x-rays through the Channeling Radiation (CR) mechanism. Typically, the xray spectrum from these sources extends up to 140 keV and this range covers the demand for most practical applications. The parameters of the electron beam determine the spectral brilliance of the x-ray source. The electron beam produced at the Fermilab new facility Advanced Superconducting Test Accelerator (ASTA) meets the requirements to assemble an experimental high brilliance CR xray source. In the first stage of the experiment the energy of the beam is 20 MeV and due to the very low emittance (more » $$\\approx 100$$ nm ) at low bunch charge (20 pC) the expected average brilliance of the x-ray source is about $10^9$ photons/[s- $(mm-mrad)^2$-0.1% BW]. In the second stage of the experiment the beam energy will be increased to 50 MeV and consequently the average brilliance will increase by a factor of five. Also, the x-ray spectrum will extend from about 30 keV to 140 keV« less

Dimensional processing of composite materials by picosecond pulsed ytterbium fiber laser

NASA Astrophysics Data System (ADS)

Kotov, S. A.

2017-12-01

In this paper, an experimental study of laser dimensional processing of thermoset carbon fiber reinforced plastics with a thickness of 2 and 3 mm was performed. In the process of work test rig setup based on picosecond pulsed fiber laser with 1.06 microns wavelength and 30 W average power was developed. Experimental tests were carried out at the maximum average power, with laser beam moved by a galvanometric mirrors system. Cutting tests were executed with different scanning velocity, using different laser modes, number of repetitions, hatching distance and focal plane position without process gas. As a result of the research recommendations for the selection processing mode parameters, providing minimal heat affected zone, good kerf geometry and high cutting speed were produced.

Effects on Vibration and Surface Roughness in High Speed Micro End-Milling of Inconel 718 with Minimum Quantity Lubrication

NASA Astrophysics Data System (ADS)

Rahman, Mohamed Abd; Yeakub Ali, Mohammad; Saddam Khairuddin, Amir

2017-03-01

This paper presents the study on vibration and surface roughness of Inconel 718 workpiece produced by micro end-milling using Mikrotools Integrated Multi-Process machine tool DT-110 with control parameters; spindle speed (15000 rpm and 30000 rpm), feed rate (2 mm/min and 4 mm/min) and depth of cut (0.10 mm and 0.15mm). The vibration was measured using DYTRAN accelerometer instrument and the average surface roughness Ra was measured using Wyko NT1100. The analysis of variance (ANOVA) by using Design Expert software revealed that feed rate and depth of cut are the most significant factors on vibration meanwhile for average surface roughness, Ra, spindle speed is the most significant factor.

Production of high energy protons with hole-boring radiation pressure acceleration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robinson, A. P. L.

The possibility of producing energetic protons with energies in the range of 100-200 MeV via hole-boring (HB) radiation pressure acceleration (RPA) at intensities around 10{sup 21} W cm{sup -2} is reexamined. It is found that hole-boring RPA can occur well below the relativistically corrected critical density in numerical simulations, with average proton energies in good agreement with established formulas. This suggests that protons in this energy range can be produced via HB RPA at around 10{sup 21} W cm{sup -2}. It is also shown that the prospects of doing this could be improved by using lasers of the same intensitymore » but longer wavelength.« less

Single-pass high harmonic generation at high repetition rate and photon flux

NASA Astrophysics Data System (ADS)

Hädrich, Steffen; Rothhardt, Jan; Krebs, Manuel; Demmler, Stefan; Klenke, Arno; Tünnermann, Andreas; Limpert, Jens

2016-09-01

Sources of short wavelength radiation with femtosecond to attosecond pulse durations, such as synchrotrons or free electron lasers, have already made possible numerous, and will facilitate more, seminal studies aimed at understanding atomic and molecular processes on fundamental length and time scales. Table-top sources of coherent extreme ultraviolet to soft x-ray radiation enabled by high harmonic generation (HHG) of ultrashort pulse lasers have also gained significant attention in the last few years due to their enormous potential for addressing a plethora of applications, therefore constituting a complementary source to large-scale facilities (synchrotrons and free electron lasers). Ti:sapphire based laser systems have been the workhorses for HHG for decades, but are limited in repetition rate and average power. On the other hand, it has been widely recognized that fostering applications in fields such as photoelectron spectroscopy and microscopy, coincidence detection, coherent diffractive imaging and frequency metrology requires a high repetition rate and high photon flux HHG sources. In this article we will review recent developments in realizing the demanding requirement of producing a high photon flux and repetition rate at the same time. Particular emphasis will be put on suitable ultrashort pulse and high average power lasers, which directly drive harmonic generation without the need for external enhancement cavities. To this end we describe two complementary schemes that have been successfully employed for high power fiber lasers, i.e. optical parametric chirped pulse amplifiers and nonlinear pulse compression. Moreover, the issue of phase-matching in tight focusing geometries will be discussed and connected to recent experiments. We will highlight the latest results in fiber laser driven high harmonic generation that currently produce the highest photon flux of all existing sources. In addition, we demonstrate the first promising applications and discuss the future direction and challenges of this new type of HHG source.

Dose equivalent near the bone-soft tissue interface from nuclear fragments produced by high-energy protons

NASA Technical Reports Server (NTRS)

Shavers, M. R.; Poston, J. W.; Cucinotta, F. A.; Wilson, J. W.

1996-01-01

During manned space missions, high-energy nucleons of cosmic and solar origin collide with atomic nuclei of the human body and produce a broad linear energy transfer spectrum of secondary particles, called target fragments. These nuclear fragments are often more biologically harmful than the direct ionization of the incident nucleon. That these secondary particles increase tissue absorbed dose in regions adjacent to the bone-soft tissue interface was demonstrated in a previous publication. To assess radiological risks to tissue near the bone-soft tissue interface, a computer transport model for nuclear fragments produced by high energy nucleons was used in this study to calculate integral linear energy transfer spectra and dose equivalents resulting from nuclear collisions of 1-GeV protons transversing bone and red bone marrow. In terms of dose equivalent averaged over trabecular bone marrow, target fragments emitted from interactions in both tissues are predicted to be at least as important as the direct ionization of the primary protons-twice as important, if recently recommended radiation weighting factors and "worst-case" geometry are used. The use of conventional dosimetry (absorbed dose weighted by aa linear energy transfer-dependent quality factor) as an appropriate framework for predicting risk from low fluences of high-linear energy transfer target fragments is discussed.

Comparison of surface characteristics of retrieved cobalt-chromium femoral heads with and without ion implantation.

PubMed

McGrory, Brian J; Ruterbories, James M; Pawar, Vivek D; Thomas, Reginald K; Salehi, Abraham B

2012-01-01

Nitrogen ion implantation of CoCr is reported to produce increased surface hardness and a lower friction surface. Femoral heads with and without ion implantation retrieved from 1997 to 2003 were evaluated for surface roughness (average surface roughness [Ra], mean peak height [Rpm], and maximum distance from peak to valley [Rmax]), nanohardness, and the ion-treated layer thickness. The difference in average Rmax (P = .033) and average Rpm (P = .008) was statistically significant, but there was no correlation between the average or maximum roughness parameters (average surface roughness, Rmax, and Rpm) and time in vivo (P > .05). Overall, nanohardness was greater for the low-friction ion-treated heads (P < .001); and it decreased with increasing time in vivo (P = .01). Ion treatment produces an increased surface hardness, but the advantage of this increased hardness appears to dissipate over time in vivo. Copyright © 2012 Elsevier Inc. All rights reserved.

Distribution, Numbers, and Diversity of ESBL-Producing E. coli in the Poultry Farm Environment

PubMed Central

Blaak, Hetty; van Hoek, Angela H. A. M.; Hamidjaja, Raditijo A.; van der Plaats, Rozemarijn Q. J.; Kerkhof-de Heer, Lianne; de Roda Husman, Ana Maria; Schets, Franciska M.

2015-01-01

This study aimed to discern the contribution of poultry farms to the contamination of the environment with ESBL-producing Escherichia coli and therewith, potentially to the spread of these bacteria to humans and other animals. ESBL-producing E. coli were detected at all investigated laying hen farms (n = 5) and broiler farms (n = 3) in 65% (46/71) and 81% (57/70) of poultry faeces samples, respectively. They were detected in rinse water and run-off water (21/26; 81%), other farm animals (11/14; 79%), dust (21/35; 60%), surface water adjacent to farms (20/35; 57%), soil (48/87; 55%), on flies (11/73; 15%), and in barn air (2/33; 6%). The highest prevalence and concentrations in the outdoor environment were observed in soil of free-range areas at laying hen farms (100% of samples positive, geometric mean concentration 2.4×104 cfu/kg), and surface waters adjacent to broiler farms during, or shortly after, cleaning between production rounds (91% of samples positive, geometric mean concentration 1.9×102 cfu/l). The diversity of ESBL-producing E. coli variants with respect to sequence type, phylogenetic group, ESBL-genotype and antibiotic resistance profile was high, especially on broiler farms where on average 16 different variants were detected, and the average Simpson’s Indices of diversity (SID; 1–D) were 0.93 and 0.94 among flock and environmental isolates respectively. At laying hen farms on average nine variants were detected, with SIDs of 0.63 (flock isolates) and 0.77 (environmental isolates). Sixty percent of environmental isolates were identical to flock isolates at the same farm. The highest proportions of ‘flock variants’ were observed in dust (94%), run-off gullies (82%), and barn air (67%), followed by surface water (57%), soil (56%), flies (50%) and other farm animals (35%).The introduction of ESBL-producing E. coli from poultry farms to the environment may pose a health risk if these bacteria reach places where people may become exposed. PMID:26270644

Effect of γ-Aminobutyric Acid-producing Lactobacillus Strain on Laying Performance, Egg Quality and Serum Enzyme Activity in Hy-Line Brown Hens under Heat Stress.

PubMed

Zhu, Y Z; Cheng, J L; Ren, M; Yin, L; Piao, X S

2015-07-01

Heat-stress remains a costly issue for animal production, especially for poultry as they lack sweat glands, and alleviating heat-stress is necessary for ensuring animal production in hot environment. A high γ-aminobutyric acid (GABA)-producer Lactobacillus strain was used to investigate the effect of dietary GABA-producer on laying performance and egg quality in heat-stressed Hy-line brown hens. Hy-Line brown hens (n = 1,164) at 280 days of age were randomly divided into 4 groups based on the amount of freeze-dried GABA-producer added to the basal diet as follows: i) 0 mg/kg, ii) 25 mg/kg, iii) 50 mg/kg, and iv) 100 mg/kg. All hens were subjected to heat-stress treatment through maintaining the temperature and the relative humidity at 28.83±3.85°C and 37% to 53.9%, respectively. During the experiment, laying rate, egg weight and feed intake of hens were recorded daily. At the 30th and 60th day after the start of the experiment, biochemical parameters, enzyme activity and immune activity in serum were measured. Egg production, average egg weight, average daily feed intake, feed conversion ratio and percentage of speckled egg, soft shell egg and misshaped egg were significantly improved (p<0.05) by the increasing supplementation of the dietary GABA-producer. Shape index, eggshell thickness, strength and weight were increased linearly with increasing GABA-producer supplementation. The level of calcium, phosphorus, glucose, total protein and albumin in serum of the hens fed GABA-producing strain supplemented diet was significantly higher (p<0.05) than that of the hens fed the basal diet, whereas cholesterol level was decreased. Compared with the basal diet, GABA-producer strain supplementation increased serum level of glutathione peroxidase (p = 0.009) and superoxide dismutase. In conclusion, GABA-producer played an important role in alleviating heat-stress, the isolated GABA-producer strain might be a potential natural and safe probiotic to use to improve laying performance and egg quality in heat-stressed hens.

The acute effect of exercise modality and nutrition manipulations on post-exercise resting energy expenditure and respiratory exchange ratio in women: a randomized trial.

PubMed

Wingfield, Hailee L; Smith-Ryan, Abbie E; Melvin, Malia N; Roelofs, Erica J; Trexler, Eric T; Hackney, Anthony C; Weaver, Mark A; Ryan, Eric D

2015-06-01

The purpose of this study was to examine the effect of exercise modality and pre-exercise carbohydrate (CHO) or protein (PRO) ingestion on post-exercise resting energy expenditure (REE) and respiratory exchange ratio (RER) in women. Twenty recreationally active women (mean ± SD; age 24.6 ± 3.9 years; height 164.4 ± 6.6 cm; weight 62.7 ± 6.6 kg) participated in this randomized, crossover, double-blind study. Each participant completed six exercise sessions, consisting of three exercise modalities: aerobic endurance exercise (AEE), high-intensity interval running (HIIT), and high-intensity resistance training (HIRT); and two acute nutritional interventions: CHO and PRO. Salivary samples were collected before each exercise session to determine estradiol-β-17 and before and after to quantify cortisol. Post-exercise REE and RER were analyzed via indirect calorimetry at the following: baseline, immediately post (IP), 30 minutes (30 min) post, and 60 minutes (60 min) post exercise. A mixed effects linear regression model, controlling for estradiol, was used to compare mean longitudinal changes in REE and RER. On average, HIIT produced a greater REE than AEE and HIRT ( p < 0.001) post exercise. Effects of AEE and HIRT were not significantly different for post-exercise REE ( p = 0.1331). On average, HIIT produced lower RER compared to either AEE or HIRT after 30 min ( p < 0.001 and p = 0.0169, respectively) and compared to AEE after 60 min ( p = 0.0020). On average, pre-exercise PRO ingestion increased post-exercise REE ( p = 0.0076) and decreased post-exercise RER ( p < 0.0001) compared to pre-exercise CHO ingestion. HIIT resulted in the largest increase in REE and largest reduction in RER.

Measuring Emotional Contagion in Social Media.

PubMed

Ferrara, Emilio; Yang, Zeyao

2015-01-01

Social media are used as main discussion channels by millions of individuals every day. The content individuals produce in daily social-media-based micro-communications, and the emotions therein expressed, may impact the emotional states of others. A recent experiment performed on Facebook hypothesized that emotions spread online, even in absence of non-verbal cues typical of in-person interactions, and that individuals are more likely to adopt positive or negative emotions if these are over-expressed in their social network. Experiments of this type, however, raise ethical concerns, as they require massive-scale content manipulation with unknown consequences for the individuals therein involved. Here, we study the dynamics of emotional contagion using a random sample of Twitter users, whose activity (and the stimuli they were exposed to) was observed during a week of September 2014. Rather than manipulating content, we devise a null model that discounts some confounding factors (including the effect of emotional contagion). We measure the emotional valence of content the users are exposed to before posting their own tweets. We determine that on average a negative post follows an over-exposure to 4.34% more negative content than baseline, while positive posts occur after an average over-exposure to 4.50% more positive contents. We highlight the presence of a linear relationship between the average emotional valence of the stimuli users are exposed to, and that of the responses they produce. We also identify two different classes of individuals: highly and scarcely susceptible to emotional contagion. Highly susceptible users are significantly less inclined to adopt negative emotions than the scarcely susceptible ones, but equally likely to adopt positive emotions. In general, the likelihood of adopting positive emotions is much greater than that of negative emotions.

Genetic selection of cattle for improved immunity and health.

PubMed

Mallard, Bonnie A; Emam, Mehdi; Paibomesai, Marlene; Thompson-Crispi, Kathleen; Wagter-Lesperance, Lauraine

2015-02-01

The immune system is a sensing structure composed of tissues and molecules that are well integrated with the neuroendocrine system. This integrate system ensures non-self from self-discrimination. In this capacity the immune system provides detection and protection from a wide range of pathogens. In mammals, the immune system is regulated by several thousand genes (8-9% of the genome) which indicate its high genetic priority as a critical fitness trait providing survival of the species. Identifying and selectively breeding livestock with the inherent ability to make superior immune responses can reduce disease occurrence, improve milk quality and increase farm profitability. Healthier animals also may be expected to demonstrate improvements in other traits, including reproductive fitness. Using the University of Guelph's patented High Immune Response technology it is possible to classify animals as high, average, or low responders based on their genetic estimated breeding value for immune responsiveness. High responders have the inherent ability to produce more balanced and robust immune responses compared with average or low responders. High responders dairy cattle essentially have about one-half the disease occurrence of low responders, and can pass their superior immune response genes on to future generations thereby accumulating health benefits within the dairy herd.

Alaska birch crafts and gifts: marketing practices and demographics.

Treesearch

Rosemarie Braden; David Nicholls

2004-01-01

Craft and gift producers in Alaska who use birch as a primary species were surveyed via mail, telephone calls, and site visits. Forty-two usable mail surveys were obtained for a response rate of 38.5 percent. Firms were in business an average of 13 years and utilized an average of 4,778 board feet of birch per year to produce a variety of craft items, including turned...

Control of particle size by feed composition in the nanolatexes produced via monomer-starved semicontinuous emulsion copolymerization.

PubMed

Sajjadi, Shahriar

2015-05-01

Conventional batch and semicontinuous emulsion copolymerizations often produce large particles whose size cannot be easily correlated with the comonomer feed compositions, and are to some degree susceptible to composition drift. In contrast, we found that copolymer nanolatexes made via semicontinuous monomer-starved emulsion copolymerizations are featured with an average nanoparticle size being controlled by the feed composition, a high conversion achieved, and a high degree of particle composition uniformity. This was achieved because the rate of particle growth, during nucleation, was controlled by the rate of comonomer addition, and the copolymer composition, surfactant parking area on the particles, and nucleation efficiency determined by the comonomer feed composition. Two model systems, methyl methacrylate/styrene and vinyl acetate/butyl acrylate, with significant differences in water solubility were studied. Monomers were added to the aqueous solution of sodium dodecylsulfate and potassium persulfate at a low rate to achieve high instantaneous conversions. Copyright © 2015 Elsevier Inc. All rights reserved.

Wastewater reclamation using discarded reverse osmosis membranes for reuse in irrigation in Djibouti, an arid country.

PubMed

Awaleh, Mohamed Osman; Ahmed, Moussa Mahdi; Soubaneh, Youssouf Djibril; Hoch, Farhan Bouraleh; Bouh, Samatar Mohamed; Dirieh, Elias Said

2013-01-01

The purpose of this paper is to establish the feasibility of recovering discarded reverse osmosis (RO) membranes in order to reduce the salinity of domestic treated wastewater. This study shows that the reuse of RO membranes is of particular interest for arid countries having naturally high mineralized water such as Djibouti. The pilot desalination unit reduces the electrical conductivity, the turbidity and the total dissolved salt respectively at 75-85, 96.7 and 95.4%. The water produced with this desalination unit contains an average of 254 cfu/100 mL total coliforms and 87 cfu/100 mL fecal coliforms. This effluent meets the World Health Organization standards for treated wastewater reuse for agricultural purposes. The annual cost of the desalination unit was evaluated as US $/m(3) 0.82, indicating the relatively high cost of this process. Nevertheless, such processes are required to produce an effluent, with a high reuse potential.

Design of a high-bunch-charge 112-MHz superconducting RF photoemission electron source

NASA Astrophysics Data System (ADS)

Xin, T.; Brutus, J. C.; Belomestnykh, Sergey A.; Ben-Zvi, I.; Boulware, C. H.; Grimm, T. L.; Hayes, T.; Litvinenko, Vladimir N.; Mernick, K.; Narayan, G.; Orfin, P.; Pinayev, I.; Rao, T.; Severino, F.; Skaritka, J.; Smith, K.; Than, R.; Tuozzolo, J.; Wang, E.; Xiao, B.; Xie, H.; Zaltsman, A.

2016-09-01

High-bunch-charge photoemission electron-sources operating in a continuous wave (CW) mode are required for many advanced applications of particle accelerators, such as electron coolers for hadron beams, electron-ion colliders, and free-electron lasers. Superconducting RF (SRF) has several advantages over other electron-gun technologies in CW mode as it offers higher acceleration rate and potentially can generate higher bunch charges and average beam currents. A 112 MHz SRF electron photoinjector (gun) was developed at Brookhaven National Laboratory to produce high-brightness and high-bunch-charge bunches for the coherent electron cooling proof-of-principle experiment. The gun utilizes a quarter-wave resonator geometry for assuring beam dynamics and uses high quantum efficiency multi-alkali photocathodes for generating electrons.

Molecular dynamics simulations of high energy cascade in ordered alloys: Defect production and subcascade division

NASA Astrophysics Data System (ADS)

Crocombette, Jean-Paul; Van Brutzel, Laurent; Simeone, David; Luneville, Laurence

2016-06-01

Displacement cascades have been calculated in two ordered alloys (Ni3Al and UO2) in the molecular dynamics framework using the CMDC (Cell Molecular Dynamics for Cascade) code (J.-P. Crocombette and T. Jourdan, Nucl. Instrum. Meth. B 352, 9 (2015)) for energies ranking between 0.1 and 580 keV. The defect production has been compared to the prediction of the NRT (Norgett, Robinson and Torrens) standard. One observes a decrease with energy of the number of defects compared to the NRT prediction at intermediate energies but, unlike what is commonly observed in elemental solids, the number of produced defects does not always turn to a linear variation with ballistic energy at high energies. The fragmentation of the cascade into subcascades has been studied through the analysis of surviving defect pockets. It appears that the common knowledge equivalence of linearity of defect production and subcascades division does not hold in general for alloys. We calculate the average number of subcascades and average number of defects per subcascades as a function of ballistic energy. We find an unexpected variety of behaviors for these two average quantities above the threshold for subcascade formation.

Morphological effects of porous poly-d,l-lactic acid/hydroxyapatite scaffolds produced by supercritical CO2 foaming on their mechanical performance.

PubMed

Rouholamin, Davood; van Grunsven, William; Reilly, Gwendolen C; Smith, Patrick J

2016-08-01

A novel supercritical CO2 foaming technique was used to fabricate scaffolds of controllable morphology and mechanical properties, with the potential to tailor the scaffolds to specific tissue engineering applications. Biodegradable scaffolds are widely used as temporary supportive structures for bone regeneration. The scaffolds must provide a sufficient mechanical support while allowing cell attachment and growth as well as metabolic activities. In this study, supercritical CO2 foaming was used to prepare fully interconnected porous scaffolds of poly-d,l-lactic acid and poly-d,l-lactic acid/hydroxyapatite. The morphological, mechanical and cell behaviours of the scaffolds were measured to examine the effect of hydroxyapatite on these properties. These scaffolds showed an average porosity in the range of 86%-95%, an average pore diameter of 229-347 µm and an average pore interconnection of 103-207 µm. The measured porosity, pore diameter, and interconnection size are suitable for cancellous bone regeneration. Compressive strength and modulus of up to 36.03 ± 5.90 and 37.97 ± 6.84 MPa were measured for the produced porous scaffolds of various compositions. The mechanical properties presented an improvement with the addition of hydroxyapatite to the structure. The relationship between morphological and mechanical properties was investigated. The matrices with different compositions were seeded with bone cells, and all the matrices showed a high cell viability and biocompatibility. The number of cells attached on the matrices slightly increased with the addition of hydroxyapatite indicating that hydroxyapatite improves the biocompatibility and proliferation of the scaffolds. The produced poly-d,l-lactic acid/hydroxyapatite scaffolds in this study showed a potential to be used as bone graft substitutes. © IMechE 2016.

Quantitative OCT-based longitudinal evaluation of intracorneal ring segment implantation in keratoconus.

PubMed

Pérez-Merino, Pablo; Ortiz, Sergio; Alejandre, Nicolas; Jiménez-Alfaro, Ignacio; Marcos, Susana

2013-09-09

To characterize the geometrical properties of keratoconic corneas upon intracorneal ring segments (ICRS) implantation, using custom-developed optical coherence tomography (OCT). Ten keratoconic corneas were measured pre- and post-ICRS surgery (7, 30, and 90 days). Corneal topographic and pachymetric maps were obtained from three-dimensional (3D) images acquired with OCT, provided with custom algorithms for image analysis, distortion correction, and quantification. The 3D positioning of the ICRS was also estimated longitudinally, relative to the pupil center and iris plane. Preoperatively, the average corneal radii of curvature were 7.02 ± 0.54 mm (anterior) and 5.40 ± 0.77 mm (posterior), and the minimum corneal thickness was 384 ± 60 μm. At 90 days, the average corneal radii of curvature were 7.26 ± 0.53 mm (anterior) and 5.44 ± 0.71 mm (posterior), and the minimum corneal thickness was 396 ± 46 μm. ICRS implantation produced a significant decrease of corneal power (by 1.71 ± 1.83 diopters [D] at 90 days). Corneal irregularities (defined by high order Zernike terms of the corneal elevation maps) and the corneal thickness distribution decreased in some patients and increased in others. The 3D ICRS depth matched the planned ICRS depth well (within 23.93 ± 23.49 μm). On average, ICRS showed an overall tilt of -6.8 ± 2.6° (temporal) and -2.1 ± 0.8° (superior) at 7 days. Spectral OCT (sOCT) provided with distortion correction and analysis tools, is an excellent instrument for evaluating the changes produced by ICRS in keratoconic corneas, and for analyzing the 3D ICRS position during the follow up. ICRS produced flattening on the anterior corneal surface, although the benefit for corneal surface regularization varied across patients.

[Effects of ß-alanine supplementation on wingate tests in university female footballers].

PubMed

Rodríguez Rodríguez, Fernando; Delgado Ormeño, Alex; Rivera Lobos, Patricio; Tapia Aranda, Víctor; Cristi-Montero, Carlos

2014-11-01

Football is a sport that develops actions intermittent high-intensity exercise using the anaerobic pathway, for that reason, the muscle fatigue would produce primarily by increasing acidosis. Carnosine, which is formed from L-histidine, ß-alanine, has proven to produce an effect "buffer" of acidosis. To determine the effect of ß-alanine supplementation, on three successive Wingate tests and compare the average power, maximum power and lactate blood in selected female college soccer. We evaluated 10 football players who were three Wingate, 5 min rest between each sprint, determining the average power, maximum and lactate at the end of each test, then consumed 2,4 gr/day of ß-alanine for 30 days and repeated the tests. The control group (n=8) performed the same tests, but without consuming the supplement. Monark cycle ergometer was used (Ergomedic 874E) and to measure lactate the Lactate Pro 2. The group with supplementation significantly improved mean power difference from the control group. The maximum power improved only in the first sprint unlike the control group and Lactate did not differ. The evidence shows that the ß-alanine improves performance on tests of more than 30 second long, but in our study improves average power and peak power even when performing consecutive sprint, being able to emulate the reality of the football game. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

Method of producing improved microstructure and properties for ceramic superconductors

DOEpatents

Singh, Jitendra P.; Guttschow, Rob A.; Dusek, Joseph T.; Poeppel, Roger B.

1996-01-01

A ceramic superconductor is produced by close control of oxygen partial pressure during sintering of the material. The resulting microstructure of YBa.sub.2 Cu.sub.3 O.sub.x indicates that sintering kinetics are enhanced at reduced p(O.sub.2). The density of specimens sintered at 910.degree. C. increased from 79 to 94% theoretical when p(O.sub.2) was decreased from 0.1 to 0.0001 MPa. The increase in density with decrease in p(O.sub.2) derives from enhanced sintering kinetics, due to increased defect concentration and decreased activation energy of the rate-controlling species undergoing diffusion. Sintering at 910.degree. C. resulted in a fine-grain microstructure, with an average grain size of approximately 4 .mu.m. Such a microstructure results in reduced microcracking, strengths as high as 191 MPa and high critical current density capacity.

Method of producing improved microstructure and properties for ceramic superconductors

DOEpatents

Singh, J.P.; Guttschow, R.A.; Dusek, J.T.; Poeppel, R.B.

1996-06-11

A ceramic superconductor is produced by close control of oxygen partial pressure during sintering of the material. The resulting microstructure of YBa{sub 2}Cu{sub 3}O{sub x} indicates that sintering kinetics are enhanced at reduced p(O{sub 2}). The density of specimens sintered at 910 C increased from 79 to 94% theoretical when p(O{sub 2}) was decreased from 0.1 to 0.0001 MPa. The increase in density with decrease in p(O{sub 2}) derives from enhanced sintering kinetics, due to increased defect concentration and decreased activation energy of the rate-controlling species undergoing diffusion. Sintering at 910 C resulted in a fine-grain microstructure, with an average grain size of approximately 4 {micro}m. Such a microstructure results in reduced microcracking, strengths as high as 191 MPa and high critical current density capacity. 20 figs.

Modified Graphene Oxide for Long Cycle Sodium-Ion Batteries

NASA Astrophysics Data System (ADS)

Shareef, Muhamed; Gunn, Harrison; Voigt, Victoria; Singh, Gurpreet

Hummer's process was modified to produce gram levels of 2-dimensional nanosheets of graphene oxide (GO) with varying degree of exfoliation and chemical functionalization. This was achieved by varying the weight ratios and reaction times of oxidizing agents used in the process. Based on Raman and Fourier transform infra red spectroscopy we show that potassium permanganate (KMnO4) is the key oxidizing agent while sodium nitrate (NaNO3) and sulfuric acid (H2SO4) play minor role during the exfoliation of graphite. Tested as working electrode in sodium-ion half-cell, the GO nanosheets produced using this optimized approach showed high rate capability and exceptionally high energy density of ~500 mAh/g for up to at least 100 cycles, which is among the highest reported for sodium/graphite electrodes. The average Coulombic efficiency was approximately 99 %. NSF Grant No. 1454151.

Elf cites 5 advantages of horizontal drilling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1984-06-01

ELF Aquitaine used horizontal drilling during a pilot test program to bring commercial production from its Rospo Mare oil discovery in the Adriatic, which would have been a costly disappointment if drilled by a conventional vertical well bore. Rospo Mare is a large reservoir containing a top column of highly viscous crude underlain by a water column. The company felt that a well bore that penetrated the reservoir vertically would bring early flooding of the oil column and yield only water. By penetrating the reservoir with a horizontal well drilled high in the oil column, the well successfully produced onmore » numerous tests from Oct. 1982 until the end of the test program in 1983. Production was termed excellent, with productivity during tests reportedly reaching ca 15 times the rate produced from nearby vertical wells. However, ELF said the results usually average ca 5 times the usual rate of vertical wells.« less

High power thyristors with 5 kV blocking voltage. Volume 1: Development of high-voltage-thyristors (4.5 kV) with good dynamic properties

NASA Technical Reports Server (NTRS)

Lock, K.; Patalong, H.; Platzoeder, K.

1979-01-01

Using neutron irradiated silicon with considerably lower spread in resistivity as compared to conventionally doped silicon it was possible to produce power thyristors with breakdown voltages between 3.5 kV and 5.5 kV. The thyristor pellets have a diameter of 50 mm. Maximum average on-state currents of 600 to 800 A can be reached with these elements. The dynamic properties of the thryistors could be improved to allow standard applications up to maximum repetitive voltages of 4.5 kV.

A novel PSB-EDI system for high ammonia wastewater treatment, biomass production and nitrogen resource recovery: PSB system.

PubMed

Wang, Hangyao; Zhou, Qin; Zhang, Guangming; Yan, Guokai; Lu, Haifeng; Sun, Liyan

A novel process coupling photosynthetic bacteria (PSB) with electrodeionization (EDI) treatment was proposed to treat high ammonia wastewater and recover bio-resources and nitrogen. The first stage (PSB treatment) was used to degrade organic pollutants and accumulate biomass, while the second stage (EDI) was for nitrogen removal and recovery. The first stage was the focus in this study. The results showed that using PSB to transform organic pollutants in wastewater into biomass was practical. PSB could acclimatize to wastewater with a chemical oxygen demand (COD) of 2,300 mg/L and an ammonia nitrogen (NH4(+)-N) concentration of 288-4,600 mg/L. The suitable pH was 6.0-9.0, the average COD removal reached 80%, and the biomass increased by an average of 9.16 times. The wastewater COD removal was independent of the NH4(+)-N concentration. Moreover, the PSB functioned effectively when the inoculum size was only 10 mg/L. The PSB-treated wastewater was then further handled in an EDI system. More than 90% of the NH4(+)-N was removed from the wastewater and condensed in the concentrate, which could be used to produce nitrogen fertilizer. In the whole system, the average NH4(+)-N removal was 94%, and the average NH4(+)-N condensing ratio was 10.0.

Sources of osmium to the modern oceans: New evidence from the 190Pt-186Os system

USGS Publications Warehouse

McDaniel, D.K.; Walker, R.J.; Hemming, S.R.; Horan, M.F.; Becker, H.; Grauch, R.I.

2004-01-01

High precision Os isotope analysis of young marine manganese nodules indicate that whereas the composition of modern seawater is radiogenic with respect to 187Os/188Os, it has 186Os/188Os that is within uncertainty of the chondritic value. Marine Mn nodule compositions thus indicate that the average continental source of Os to modern seawater had long-term high Re/Os compared to Pt/Os. Analyses of loess and freshwater Mn nodules support existing evidence that average upper continental crust (UCC) has resolvably suprachondritic 186Os/188Os, as well as radiogenic 187Os/188Os. Modeling the composition of seawater as a two-component mixture of oceanic/cosmic Os with chondritic Os compositions and continentally-derived Os demonstrates that, insofar as estimates for the composition of average UCC are accurate, congruently weathered average UCC cannot be the sole continental source of Os to seawater. Our analysis of four Cambrian black shales confirm that organic-rich sediments can have 187Os/188Os ratios that are much higher than average UCC, but 186Os/188Os compositions that are generally between those of chondrites and average-UCC. Preferential weathering of black shales can result in dissolved Os discharged to the ocean basins that has a much lower 186Os/188Os than does average upper crust. Modeling the available data demonstrates that augmentation of estimated average UCC compositions with less than 0.1% additional black shale and 1.4% additional ultramafic rock can produce a continental end-member Os isotopic composition that satisfies the requirements imposed by the marine Mn nodule data. The interplay of these two sources provides a mechanism by which the 187Os/188Os of seawater can change as sources and weathering conditions change, yet seawater 186Os/188Os varies only minimally. ?? 2004 Elsevier Ltd.

Semirational Approach for Ultrahigh Poly(3-hydroxybutyrate) Accumulation in Escherichia coli by Combining One-Step Library Construction and High-Throughput Screening.

PubMed

Li, Teng; Ye, Jianwen; Shen, Rui; Zong, Yeqing; Zhao, Xuejin; Lou, Chunbo; Chen, Guo-Qiang

2016-11-18

As a product of a multistep enzymatic reaction, accumulation of poly(3-hydroxybutyrate) (PHB) in Escherichia coli (E. coli) can be achieved by overexpression of the PHB synthesis pathway from a native producer involving three genes phbC, phbA, and phbB. Pathway optimization by adjusting expression levels of the three genes can influence properties of the final product. Here, we reported a semirational approach for highly efficient PHB pathway optimization in E. coli based on a phbCAB operon cloned from the native producer Ralstonia entropha (R. entropha). Rationally designed ribosomal binding site (RBS) libraries with defined strengths for each of the three genes were constructed based on high or low copy number plasmids in a one-pot reaction by an oligo-linker mediated assembly (OLMA) method. Strains with desired properties were evaluated and selected by three different methodologies, including visual selection, high-throughput screening, and detailed in-depth analysis. Applying this approach, strains accumulating 0%-92% PHB contents in cell dry weight (CDW) were achieved. PHB with various weight-average molecular weights (M w ) of 2.7-6.8 × 10 6 were also efficiently produced in relatively high contents. These results suggest that the semirational approach combining library design, construction, and proper screening is an efficient way to optimize PHB and other multienzyme pathways.

24 CFR 51.103 - Criteria and standards.

Code of Federal Regulations, 2011 CFR

2011-04-01

...-night average sound level produced as the result of the accumulation of noise from all sources contributing to the external noise environment at the site. Day-night average sound level, abbreviated as DNL and symbolized as Ldn, is the 24-hour average sound level, in decibels, obtained after addition of 10...

Simultaneous valorization and biocatalytic upgrading of heavy vacuum gas oil by the biosurfactant-producing Pseudomonas aeruginosa AK6U.

PubMed

Ismail, Wael Ahmed; Mohamed, Magdy El-Said; Awadh, Maysoon N; Obuekwe, Christian; El Nayal, Ashraf M

2017-11-01

Heavy vacuum gas oil (HVGO) is a complex and viscous hydrocarbon stream that is produced as the bottom side product from the vacuum distillation units in petroleum refineries. HVGO is conventionally treated with thermochemical process, which is costly and environmentally polluting. Here, we investigate two petroleum biotechnology applications, namely valorization and bioupgrading, as green approaches for valorization and upgrading of HVGO. The Pseudomonas aeruginosa AK6U strain grew on 20% v/v of HVGO as a sole carbon and sulfur source. It produced rhamnolipid biosurfactants in a growth-associated mode with a maximum crude biosurfactants yield of 10.1 g l -1 , which reduced the surface tension of the cell-free culture supernatant to 30.6 mN m -1 within 1 week of incubation. The rarely occurring dirhamnolipid Rha-Rha-C 12 -C 12 dominated the congeners' profile of the biosurfactants produced from HVGO. Heavy vacuum gas oil was recovered from the cultures and abiotic controls and the maltene fraction was extracted for further analysis. Fractional distillation (SimDist) of the biotreated maltene fraction showed a relative decrease in the high-boiling heavy fuel fraction (BP 426-565 °C) concomitant with increase in the lighter distillate diesel fraction (BP 315-426 °C). Analysis of the maltene fraction revealed compositional changes. The number-average (Mn) and weight-average (Mw) molecular weights, as well as the absolute number of hydrocarbons and sulfur heterocycles were higher in the biotreated maltene fraction of HVGO. These findings suggest that HVGO can be potentially exploited as a carbon-rich substrate for production of the high-value biosurfactants by P. aeruginosa AK6U and to concomitantly improve/upgrade its chemical composition. © 2017 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

Neuropeptide Y in phaeochromocytomas and ganglioneuroblastomas.

PubMed

Adrian, T E; Allen, J M; Terenghi, G; Bacarese-Hamilton, A J; Brown, M J; Polak, J M; Bloom, S R

1983-09-03

Tumour tissue from nineteen patients with phaeochromocytomas and nine with ganglioneuroblastomas contained large numbers of neuropeptide Y (NPY) producing cells and extracts of these tumours had very high concentrations of immunoreactive NPY. Plasma NPY concentrations were also raised, averaging 460 pmol/l in patients with tumours of the sympathetic chain and 55 pmol/l in healthy controls. Since plasma NPY is straightforward to measure and relatively stable, its estimation may prove helpful as a screening tests for phaeochromocytoma.

Wage Inequality and Violent Protests in Oil/Gas Producing Countries

NASA Astrophysics Data System (ADS)

Nuraliyev, Nurlan

This work examines contrasting claims made by academic scholars on the relationship between income inequality and political discontent. Does income inequality directly cause social unrest or is this relationship conditional on the level of democratic development? Using the data from 55 oil/gas producing countries between 2010-2013, the author finds: 1) income disparity between an average income per capita of local population and an average income of foreign labor employed in the oil/gas industry results in higher number of violent protests in more democratic oil/gas producing societies; 2) wage disparity between local and foreign labor in the oil/gas industry is associated with higher number of protests in this industry in more democratic oil/gas producing states.

Pilot-scale study on the treatment of basal aquifer water using ultrafiltration, reverse osmosis and evaporation/crystallization to achieve zero-liquid discharge.

PubMed

Loganathan, Kavithaa; Chelme-Ayala, Pamela; Gamal El-Din, Mohamed

2016-01-01

Basal aquifer water is deep groundwater found at the bottom of geological formations, underlying bitumen-saturated sands. Some of the concerns associated with basal aquifer water at the Athabasca oil sands are the high concentrations of hardness-causing compounds, alkalinity, and total dissolved solids. The objective of this pilot-scale study was to treat basal aquifer water to a quality suitable for its reuse in the production of synthetic oil. To achieve zero-liquid discharge (ZLD) conditions, the treatment train included chemical oxidation, polymeric ultrafiltration (UF), reverse osmosis (RO), and evaporation-crystallization technologies. The results indicated that the UF unit was effective in removing solids, with UF filtrate turbidity averaging 2.0 NTU and silt density index averaging 0.9. Membrane autopsies indicated that iron was the primary foulant on the UF and RO membranes. Laboratory and pilot-scale tests on RO reject were conducted to determine the feasibility of ZLD crystallization. Due to the high amounts of calcium, magnesium, and bicarbonate in the RO reject, softening of the feed was required to avoid scaling in the evaporator. Crystals produced throughout the testing were mainly sodium chloride. The results of this study indicated that the ZLD approach was effective in both producing freshwater and minimizing brine discharges. Copyright © 2015 Elsevier Ltd. All rights reserved.

An Intriguing Convex Break in the EGRET SED of Mrk 421

NASA Technical Reports Server (NTRS)

Nandikotkur, Giridhar; Jahoda, Keith M.; Georganopoulos, M.; Hartman, R. C.; Mukherjee, R.; Thompson, D. J.; Swank, Jean H.

2007-01-01

Based upon analysis of the entire EGRET data from Mrk 421, it is found that the time-averaged spectra are inconsistent with the predictions of current theoretical models that have had success in describing simultaneous X-ray/TeV observations, and suggest additional components in the GeV band, as well as complex time variability. Current theoretical pictures explain the GeV emission as comptonization of the synchrotron photons in the jet, and predict hard spectra that should join smoothly with the TeV emission. Our analysis shows that the situation is more complex. The spectrum ranges from hard to soft during individual epochs, and shows a convext break in the aggregated data. We also present the mission-averaged EGRET spectrum for PKS 2155-304, which shows a similar (but not as pronounced) convex curvature. We discuss a series of possible explanations for the 10(exp 22) - 10(exp 23) HZ declining part of the EGRET nu F(sub nu), spectrum for Mrk 421, and suggest that it is synchrotron emission from the high energy tail of the electron population that produces the X-rays during the highest X-ray states. Such multi-MeV photons are produced by electrons accelerated close to the limit of diffusive shock acceleration. Simultaneous GLAST and X-ray observations of high X-ray states will address the issue of the convex curvature in the future.

System Evaluation and Life-Cycle Cost Analysis of a Commercial-Scale High-Temperature Electrolysis Hydrogen Production Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwin A. Harvego; James E. O'Brien; Michael G. McKellar

2012-11-01

Results of a system evaluation and lifecycle cost analysis are presented for a commercial-scale high-temperature electrolysis (HTE) central hydrogen production plant. The plant design relies on grid electricity to power the electrolysis process and system components, and industrial natural gas to provide process heat. The HYSYS process analysis software was used to evaluate the reference central plant design capable of producing 50,000 kg/day of hydrogen. The HYSYS software performs mass and energy balances across all components to allow optimization of the design using a detailed process flow sheet and realistic operating conditions specified by the analyst. The lifecycle cost analysismore » was performed using the H2A analysis methodology developed by the Department of Energy (DOE) Hydrogen Program. This methodology utilizes Microsoft Excel spreadsheet analysis tools that require detailed plant performance information (obtained from HYSYS), along with financial and cost information to calculate lifecycle costs. The results of the lifecycle analyses indicate that for a 10% internal rate of return, a large central commercial-scale hydrogen production plant can produce 50,000 kg/day of hydrogen at an average cost of $2.68/kg. When the cost of carbon sequestration is taken into account, the average cost of hydrogen production increases by $0.40/kg to $3.08/kg.« less

A framework for activity detection in wide-area motion imagery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Porter, Reid B; Ruggiero, Christy E; Morrison, Jack D

2009-01-01

Wide-area persistent imaging systems are becoming increasingly cost effective and now large areas of the earth can be imaged at relatively high frame rates (1-2 fps). The efficient exploitation of the large geo-spatial-temporal datasets produced by these systems poses significant technical challenges for image and video analysis and data mining. In recent years there has been significant progress made on stabilization, moving object detection and tracking and automated systems now generate hundreds to thousands of vehicle tracks from raw data, with little human intervention. However, the tracking performance at this scale, is unreliable and average track length is much smallermore » than the average vehicle route. This is a limiting factor for applications which depend heavily on track identity, i.e. tracking vehicles from their points of origin to their final destination. In this paper we propose and investigate a framework for wide-area motion imagery (W AMI) exploitation that minimizes the dependence on track identity. In its current form this framework takes noisy, incomplete moving object detection tracks as input, and produces a small set of activities (e.g. multi-vehicle meetings) as output. The framework can be used to focus and direct human users and additional computation, and suggests a path towards high-level content extraction by learning from the human-in-the-loop.« less

USSR Report, Agriculture

DTIC Science & Technology

1984-05-22

organizational and agro- technical measures will enable us, in our opinion, to produce an average of 37-38 quintals of corn grain per hectare and to...average of 322 quintals of roots and to produce 32-33 quintals of sugar per hectare. They are up to this task. The essential foundation for the...of seed -- or 4.8 quintals per hectare. In 1983 the Zarya Kolkhoz in Krasnogvardeyskiy Rayon in Stavropol Kray obtained 3.5 quintals of seed from

Energy from vascular plant wastewater treatment systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wolverton, B.C.; McDonald, R.C.

1981-04-01

Water hyacinth (Eichhornia crassipes) duckweed (Spirodela sp. and Lemna sp.), water pennywort (Hydrocotyle ranunculoides), and kudzu (Pueraria lobata) were anaerobically fermented using an anaerobic filter technique that reduced the total digestion time from 90 d to an average of 23 d and produced 0.14 to 0.22 m/sup 3/ CH/sub 4//kg (dry weight) (2.3 to 3.6 ft/sup 3//lb) from mature filters for the 3 aquatic species. Kudzu required an average digestion time of 33 d and produced an average of 0.21 m/sup 3/ CH/sub 4//kg (dry weight) (3.4 ft/sup 3//lb). The anaerobic filter provided a large surface area for the anaerobicmore » bacteria to establish and maintain an optimal balance of facultative, acid-forming, and methane-producing bacteria. Consequently the efficiency of the process was greatly improved over prior batch fermentations.« less

Adsorbent materials from paper industry waste materials and their use in Cu(II) removal from water.

PubMed

Méndez, A; Barriga, S; Fidalgo, J M; Gascó, G

2009-06-15

This paper deals with the removal of Cu(2+) from water using adsorbent materials prepared from paper industry waste materials (one de-inking paper sludge and other sludge from virgin pulp mill). Experimental results showed that de-inking paper sludge leads to mesoporous materials (V(mic)/V(T)=0.13 and 0.14), whereas the sludge from virgin pulp mill produces high microporous adsorbents (V(mic)/V(T)=0.39 and 0.41). Adsorbent materials were then used for Cu(2+) removal from water at acid pH. During water treatment, heavy metals lixiviation from adsorbent materials was not produced. However, important Ca and Mg leaching was observed. Final pH significantly increases after treatment of water with adsorbent materials probably due to their elevated CaCO(3) content. In general, highest Cu(2+) removal was obtained using adsorbent materials from de-inking paper sludge. This result could be due to their higher content in oxygenated surface groups, high average pore diameter, elevated superficial charge density, high CaCO(3) amount and high Ca and Mg exchange content.

Facile and Scalable Fabrication of Highly Efficient Lead Iodide Perovskite Thin-Film Solar Cells in Air Using Gas Pump Method.

PubMed

Ding, Bin; Gao, Lili; Liang, Lusheng; Chu, Qianqian; Song, Xiaoxuan; Li, Yan; Yang, Guanjun; Fan, Bin; Wang, Mingkui; Li, Chengxin; Li, Changjiu

2016-08-10

Control of the perovskite film formation process to produce high-quality organic-inorganic metal halide perovskite thin films with uniform morphology, high surface coverage, and minimum pinholes is of great importance to highly efficient solar cells. Herein, we report on large-area light-absorbing perovskite films fabrication with a new facile and scalable gas pump method. By decreasing the total pressure in the evaporation environment, the gas pump method can significantly enhance the solvent evaporation rate by 8 times faster and thereby produce an extremely dense, uniform, and full-coverage perovskite thin film. The resulting planar perovskite solar cells can achieve an impressive power conversion efficiency up to 19.00% with an average efficiency of 17.38 ± 0.70% for 32 devices with an area of 5 × 2 mm, 13.91% for devices with a large area up to 1.13 cm(2). The perovskite films can be easily fabricated in air conditions with a relative humidity of 45-55%, which definitely has a promising prospect in industrial application of large-area perovskite solar panels.

Achieving high peak capacity production for gas chromatography and comprehensive two-dimensional gas chromatography by minimizing off-column peak broadening.

PubMed

Wilson, Ryan B; Siegler, W Christopher; Hoggard, Jamin C; Fitz, Brian D; Nadeau, Jeremy S; Synovec, Robert E

2011-05-27

By taking into consideration band broadening theory and using those results to select experimental conditions, and also by reducing the injection pulse width, peak capacity production (i.e., peak capacity per separation time) is substantially improved for one dimensional (1D-GC) and comprehensive two dimensional (GC×GC) gas chromatography. A theoretical framework for determining the optimal linear gas velocity (the linear gas velocity producing the minimum H), from experimental parameters provides an in-depth understanding of the potential for GC separations in the absence of extra-column band broadening. The extra-column band broadening is referred to herein as off-column band broadening since it is additional band broadening not due to the on-column separation processes. The theory provides the basis to experimentally evaluate and improve temperature programmed 1D-GC separations, but in order to do so with a commercial 1D-GC instrument platform, off-column band broadening from injection and detection needed to be significantly reduced. Specifically for injection, a resistively heated transfer line is coupled to a high-speed diaphragm valve to provide a suitable injection pulse width (referred to herein as modified injection). Additionally, flame ionization detection (FID) was modified to provide a data collection rate of 5kHz. The use of long, relatively narrow open tubular capillary columns and a 40°C/min programming rate were explored for 1D-GC, specifically a 40m, 180μm i.d. capillary column operated at or above the optimal average linear gas velocity. Injection using standard auto-injection with a 1:400 split resulted in an average peak width of ∼1.5s, hence a peak capacity production of 40peaks/min. In contrast, use of modified injection produced ∼500ms peak widths for 1D-GC, i.e., a peak capacity production of 120peaks/min (a 3-fold improvement over standard auto-injection). Implementation of modified injection resulted in retention time, peak width, peak height, and peak area average RSD%'s of 0.006, 0.8, 3.4, and 4.0%, respectively. Modified injection onto the first column of a GC×GC coupled with another high-speed valve injection onto the second column produced an instrument with high peak capacity production (500-800peaks/min), ∼5-fold to 8-fold higher than typically reported for GC×GC. Copyright © 2011 Elsevier B.V. All rights reserved.

Meristem culture and subsequent micropropagation of Chilean strawberry (Fragaria chiloensis (L.) Duch.).

PubMed

Quiroz, Karla A; Berríos, Miguel; Carrasco, Basilio; Retamales, Jorge B; Caligari, Peter D S; García-Gonzáles, Rolando

2017-06-02

Vegetative propagation of Fragaria sp. is traditionally carried out using stolons. This system of propagation, in addition to being slow, can spread plant diseases, particularly serious being viral. In vitro culture of meristems and the establishment of micropropagation protocols are important tools for solving these problems. In recent years, considerable effort has been made to develop in vitro propagation of the commercial strawberry in order to produce virus-free plants of high quality. These previous results can serve as the basis for developing in vitro-based propagation technologies in the less studied species Fragaria chiloensis. In this context, we studied the cultivation of meristems and establishment of a micropropagation protocol for F. chiloensis. The addition of polyvinylpyrrolidone (PVP) improved the meristem regeneration efficiency of F. chiloensis accessions. Similarly, the use of 6-benzylaminopurine (BAP) in the culture media increased the average rate of multiplication to 3-6 shoots per plant. In addition, the use of 6-benzylaminopurine (BAP), had low levels (near zero) of explant losses due to oxidation. However, plant height as well as number of leaves and roots were higher in media without growth regulators, with average values of 0.5 cm, 9 leaves and 4 roots per plant. For the first time in Chilean strawberry, meristem culture demonstrated to be an efficient tool for eliminating virus from infected plants, giving the possibility to produce disease free propagation material. Also, the addition of PVP into the basal MS medium improved the efficiency of plant recovery from isolated meristems. Farmers can now access to high quality plant material produced by biotech tools which will improve their technological practices.

Bistability, non-ergodicity, and inhibition in pairwise maximum-entropy models

PubMed Central

Grün, Sonja; Helias, Moritz

2017-01-01

Pairwise maximum-entropy models have been used in neuroscience to predict the activity of neuronal populations, given only the time-averaged correlations of the neuron activities. This paper provides evidence that the pairwise model, applied to experimental recordings, would produce a bimodal distribution for the population-averaged activity, and for some population sizes the second mode would peak at high activities, that experimentally would be equivalent to 90% of the neuron population active within time-windows of few milliseconds. Several problems are connected with this bimodality: 1. The presence of the high-activity mode is unrealistic in view of observed neuronal activity and on neurobiological grounds. 2. Boltzmann learning becomes non-ergodic, hence the pairwise maximum-entropy distribution cannot be found: in fact, Boltzmann learning would produce an incorrect distribution; similarly, common variants of mean-field approximations also produce an incorrect distribution. 3. The Glauber dynamics associated with the model is unrealistically bistable and cannot be used to generate realistic surrogate data. This bimodality problem is first demonstrated for an experimental dataset from 159 neurons in the motor cortex of macaque monkey. Evidence is then provided that this problem affects typical neural recordings of population sizes of a couple of hundreds or more neurons. The cause of the bimodality problem is identified as the inability of standard maximum-entropy distributions with a uniform reference measure to model neuronal inhibition. To eliminate this problem a modified maximum-entropy model is presented, which reflects a basic effect of inhibition in the form of a simple but non-uniform reference measure. This model does not lead to unrealistic bimodalities, can be found with Boltzmann learning, and has an associated Glauber dynamics which incorporates a minimal asymmetric inhibition. PMID:28968396

Kinematic Patterns Associated with the Vertical Force Produced during the Eggbeater Kick.

PubMed

Oliveira, Nuno; Chiu, Chuang-Yuan; Sanders, Ross H

2015-01-01

The purpose of this study was to determine the kinematic patterns that maximized the vertical force produced during the water polo eggbeater kick. Twelve water polo players were tested executing the eggbeater kick with the trunk aligned vertically and with the upper limbs above water while trying to maintain as high a position as possible out of the water for nine eggbeater kick cycles. Lower limb joint angular kinematics, pitch angles and speed of the feet were calculated. The vertical force produced during the eggbeater kick cycle was calculated using inverse dynamics for the independent lower body segments and combined upper body segments, and a participant-specific second-degree regression equation for the weight and buoyancy contributions. Vertical force normalized to body weight was associated with hip flexion (average, r = 0.691; maximum, r = 0.791; range of motion, r = 0.710), hip abduction (maximum, r = 0.654), knee flexion (average, r = 0.716; minimum, r = 0.653) and knee flexion-extension angular velocity (r = 0.758). Effective orientation of the hips resulted in fast horizontal motion of the feet with positive pitch angles. Vertical motion of the feet was negatively associated with vertical force. A multiple regression model comprising the non-collinear variables of maximum hip abduction, hip flexion range of motion and knee flexion angular velocity accounted for 81% of the variance in normalized vertical force. For high performance in the water polo, eggbeater kick players should execute fast horizontal motion with the feet by having large abduction and flexion of the hips, and fast extension and flexion of the knees.

Bistability, non-ergodicity, and inhibition in pairwise maximum-entropy models.

PubMed

Rostami, Vahid; Porta Mana, PierGianLuca; Grün, Sonja; Helias, Moritz

2017-10-01

Pairwise maximum-entropy models have been used in neuroscience to predict the activity of neuronal populations, given only the time-averaged correlations of the neuron activities. This paper provides evidence that the pairwise model, applied to experimental recordings, would produce a bimodal distribution for the population-averaged activity, and for some population sizes the second mode would peak at high activities, that experimentally would be equivalent to 90% of the neuron population active within time-windows of few milliseconds. Several problems are connected with this bimodality: 1. The presence of the high-activity mode is unrealistic in view of observed neuronal activity and on neurobiological grounds. 2. Boltzmann learning becomes non-ergodic, hence the pairwise maximum-entropy distribution cannot be found: in fact, Boltzmann learning would produce an incorrect distribution; similarly, common variants of mean-field approximations also produce an incorrect distribution. 3. The Glauber dynamics associated with the model is unrealistically bistable and cannot be used to generate realistic surrogate data. This bimodality problem is first demonstrated for an experimental dataset from 159 neurons in the motor cortex of macaque monkey. Evidence is then provided that this problem affects typical neural recordings of population sizes of a couple of hundreds or more neurons. The cause of the bimodality problem is identified as the inability of standard maximum-entropy distributions with a uniform reference measure to model neuronal inhibition. To eliminate this problem a modified maximum-entropy model is presented, which reflects a basic effect of inhibition in the form of a simple but non-uniform reference measure. This model does not lead to unrealistic bimodalities, can be found with Boltzmann learning, and has an associated Glauber dynamics which incorporates a minimal asymmetric inhibition.

Extraordinary flood response of a small urban watershed to short-duration convective rainfall

USGS Publications Warehouse

Smith, J.A.; Miller, A.J.; Baeck, M.L.; Nelson, P.A.; Fisher, G.T.; Meierdiercks, K.L.

2005-01-01

The 9.1 km2 Moores Run watershed in Baltimore, Maryland, experiences floods with unit discharge peaks exceeding 1 m3 s-1 km-2 12 times yr-1, on average. Few, if any, drainage basins in the continental United States have a higher frequency. A thunderstorm system on 13 June 2003 produced the record flood peak (13.2 m3 s-1 km-2) during the 6-yr stream gauging record of Moores Run. In this paper, the hydrometeorology, hydrology, and hydraulics of extreme floods in Moores Run are examined through analyses of the 13 June 2003 storm and flood, as well as other major storm and flood events during the 2000-03 time period. The 13 June 2003 flood, like most floods in Moores Run, was produced by an organized system of thunderstorms. Analyses of the 13 June 2003 storm, which are based on volume scan reflectivity observations from the Sterling, Virginia, WSR-88D radar, are used to characterize the spatial and temporal variability of flash flood producing rainfall. Hydrology of flood response in Moores Run is characterized by highly efficient concentration of runoff through the storm drain network and relatively low runoff ratios. A detailed survey of high-water marks for the 13 June 2003 flood is used, in combination with analyses based on a 2D, depth-averaged open channel flow model (TELEMAC 2D) to examine hydraulics of the 13 June 2003 flood. Hydraulic analyses are used to examine peak discharge estimates for the 13 June flood peak, propagation of flood waves in the Moores Run channel, and 2D flow features associated with channel and floodplain geometry. ?? 2005 American Meteorological Society.

Vegetable output and cost savings of community gardens in San Jose, California.

PubMed

Algert, Susan J; Baameur, Aziz; Renvall, Marian J

2014-07-01

Urban dwellers across the United States increasingly access a variety of fresh vegetables through participation in neighborhood-level community gardens. Here we document vegetable output and cost savings of community gardens in the city of San Jose, CA, to better understand the capacity of community gardens to affect food affordability in an urban setting. A convenience sample of 83 community gardeners in San Jose completed a background survey during spring and summer 2012. On average, gardeners were aged 57 years and had a monthly income of $4,900; 25% had completed college. A representative subset of 10 gardeners was recruited to weigh vegetable output of their plots using portable electronic scales at three separate garden sites. Accuracy of each portable scale was verified by comparing the weight of a sample vegetable to weights obtained using a lab scale precise to 0.2 oz. Garden yields and cost savings were tabulated overall for each plot. Results indicate that community garden practices are more similar to biointensive high-production farming, producing 0.75 lb vegetables/sq ft, rather than conventional agricultural practices, producing 0.60 lb/sq ft. Gardens produced on average 2.55 lb/plant and saved $435 per plot for the season. Results indicate that cost savings are greatest if vertical high value crops such as tomatoes and peppers are grown in community gardens, although yields depend on growing conditions, gardener's skill, availability of water, and other factors. Future research is needed to document cost savings and yields for specific crops grown in community gardens. Copyright © 2014 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

Prevention of colonization and infection by Klebsiella pneumoniae carbapenemase-producing enterobacteriaceae in long-term acute-care hospitals.

PubMed

Hayden, Mary K; Lin, Michael Y; Lolans, Karen; Weiner, Shayna; Blom, Donald; Moore, Nicholas M; Fogg, Louis; Henry, David; Lyles, Rosie; Thurlow, Caroline; Sikka, Monica; Hines, David; Weinstein, Robert A

2015-04-15

Klebsiella pneumoniae carbapenemase-producing Enterobacteriaceae (hereafter "KPC") are an increasing threat to healthcare institutions. Long-term acute-care hospitals (LTACHs) have especially high prevalence of KPC. Using a stepped-wedge design, we tested whether a bundled intervention (screening patients for KPC rectal colonization upon admission and every other week; contact isolation and geographic separation of KPC-positive patients in ward cohorts or single rooms; bathing all patients daily with chlorhexidine gluconate; and healthcare-worker education and adherence monitoring) would reduce colonization and infection due to KPC in 4 LTACHs with high endemic KPC prevalence. The study was conducted between 1 February 2010 and 30 June 2013; 3894 patients were enrolled during the preintervention period (lasting from 16 to 29 months), and 2951 patients were enrolled during the intervention period (lasting from 12 to 19 months). KPC colonization prevalence was stable during preintervention (average, 45.8%; 95% confidence interval [CI], 42.1%-49.5%), declined early during intervention, then reached a plateau (34.3%; 95% CI, 32.4%-36.2%; P<.001 for exponential decline). During intervention, KPC admission prevalence remained high (average, 20.6%, 95% CI, 19.1%-22.3%). The incidence rate of KPC colonization fell during intervention, from 4 to 2 acquisitions per 100 patient-weeks (P=.004 for linear decline). Compared to preintervention, average rates of clinical outcomes declined during intervention: KPC in any clinical culture (3.7 to 2.5/1000 patient-days; P=.001), KPC bacteremia (0.9 to 0.4/1000 patient-days; P=.008), all-cause bacteremia (11.2 to 7.6/1000 patient-days; P=.006) and blood culture contamination (4.9 to 2.3/1000 patient-days; P=.03). A bundled intervention was associated with clinically important and statistically significant reductions in KPC colonization, KPC infection, all-cause bacteremia, and blood culture contamination in a high-risk LTACH population. © The Author 2014. Published by Oxford University Press on behalf of the Infectious Diseases Society of America. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Low Cost Nuclear Thermal Rocket Cermet Fuel Element Environment Testing

NASA Technical Reports Server (NTRS)

Bradley, D. E.; Mireles, O. R.; Hickman, R. R.

2011-01-01

Deep space missions with large payloads require high specific impulse and relatively high thrust to achieve mission goals in reasonable time frames.1,2 Conventional storable propellants produce average specific impulse. Nuclear thermal rockets capable of producing high specific impulse are proposed. Nuclear thermal rockets employ heat produced by fission reaction to heat and therefore accelerate hydrogen, which is then forced through a rocket nozzle providing thrust. Fuel element temperatures are very high (up to 3000 K), and hydrogen is highly reactive with most materials at high temperatures. Data covering the effects of high-temperature hydrogen exposure on fuel elements are limited.3 The primary concern is the mechanical failure of fuel elements that employ high-melting-point metals, ceramics, or a combination (cermet) as a structural matrix into which the nuclear fuel is distributed. The purpose of the testing is to obtain data to assess the properties of the non-nuclear support materials, as-fabricated, and determine their ability to survive and maintain thermal performance in a prototypical NTR reactor environment of exposure to hydrogen at very high temperatures. The fission process of the planned fissile material and the resulting heating performance is well known and does not therefore require that active fissile material be integrated in this testing. A small-scale test bed designed to heat fuel element samples via non-contact radio frequency heating and expose samples to hydrogen is being developed to assist in optimal material and manufacturing process selection without employing fissile material. This paper details the test bed design and results of testing conducted to date.

FY2005 Progress Summary and FY2006 Program Plan Statement of Work and Deliverables for Development of High Average Power Diode-Pumped Solid State Lasers, and Complementary Technologies, for Applications in Energy and Defense

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ebbers, C

The primary focus this year was to operate the system with two amplifiers populated with and pumped by eight high power diode arrays. The system was operated for extended run periods which enabled average power testing of components, diagnostics, and controls. These tests were highly successful, with a demonstrated energy level of over 55 joules for 4 cumulative hours at a repetition rate of 10 Hz (average power 0.55 kW). In addition, high average power second harmonic generation was demonstrated, achieving 227 W of 523.5 nm light (22.7 J, 10 Hz, 15 ns, 30 minutes) Plans to achieve higher energymore » levels and average powers are in progress. The dual amplifier system utilizes a 4-pass optical arrangement. The Yb:S-FAP slabs were mounted in aerodynamic aluminum vane structures to allow turbulent helium gas flow across the faces. Diagnostic packages that monitored beam performance were deployed during operation. The laser experiments involved injecting a seed beam from the front end into the system and making four passes through both amplifiers. Beam performance diagnostics monitored the beam on each pass to assess system parameters such as gain and nearfield intensity profiles. This year, an active mirror and wavefront sensor were procured and demonstrated in an off-line facility. The active mirror technology can correct for low order phase distortions at user specified operating conditions (such as repetition rates different than 10 Hz) and is a complementary technology to the static phase plates used in the system for higher order distortions. A picture of the laser system with amplifier No.2 (foreground) and amplifier No.1 (background) is shown in Fig. 1.0.1.1. The control system and diagnostics were recently enhanced for faster processing and allow remote operation of the system. The growth and fabrication of the Yb:S-FAP slabs constituted another major element of our program objectives. Our goal was to produce at least fourteen 4x6 cm2 crystalline slabs. These goals were met. Nine crystal boules were successfully grown to produce 14 slabs. In addition, we have prepared the way to scale the Yb:S-FAP crystals to the next growth diameter (10-inch diameter as opposed to 7-inch diameter). An outside contract was placed with Northrop-Grumman to scaleup the Yb:S-FAP crystal size. The following sections discuss the above accomplishments in more technical detail and are followed by plans and a budget request for FY2006.« less

Novel First-Level Interconnect Techniques for Flip Chip on MEMS Devices

PubMed Central

Sutanto, Jemmy; Anand, Sindhu; Patel, Chetan; Muthuswamy, Jit

2013-01-01

Flip-chip packaging is desirable for microelectro-mechanical systems (MEMS) devices because it reduces the overall package size and allows scaling up the number of MEMS chips through 3-D stacks. In this report, we demonstrate three novel techniques to create first-level interconnect (FLI) on MEMS: 1) Dip and attach technology for Ag epoxy; 2) Dispense technology for solder paste; 3) Dispense, pull, and attach technology (DPAT) for solder paste. The above techniques required no additional microfabrication steps, produced no visible surface contamination on the MEMS active structures, and generated high-aspect-ratio interconnects. The developed FLIs were successfully tested on MEMS moveable microelectrodes microfabricated by SUMMiTVTM process producing no apparent detrimental effect due to outgassing. The bumping processes were successfully applied on Al-deposited bond pads of 100 μm × 100 μm with an average bump height of 101.3 μm for Ag and 184.8 μm for solder (63Sn, 37Pb). DPAT for solder paste produced bumps with the aspect ratio of 1.8 or more. The average shear strengths of Ag and solder bumps were 78 MPa and 689 kPa, respectively. The electrical test on Ag bumps at 794 A/cm2 demonstrated reliable electrical interconnects with negligible resistance. These scalable FLI technologies are potentially useful for MEMS flip-chip packaging and 3-D stacking. PMID:24504168

Geopolymerisation of silt generated from construction and demolition waste washing plants.

PubMed

Lampris, C; Lupo, R; Cheeseman, C R

2009-01-01

Recycling plants that size, sort and wash construction and demolition waste can produce high quality aggregate. However, they also produce up to 80ton per hour of filter cake waste containing fine (<63mum) silt particles that is classified as inert waste and normally landfilled. This research investigated the potential to form geopolymers containing silt, which would allow this problematic waste to be beneficially reused as aggregate. This would significantly improve the economic viability of recycling plants that wash wastes. Silt filter cakes have been collected from a number of aggregate washing plants operating in the UK. These were found to contain similar aluminosilicate crystalline phases. Geopolymer samples were produced using silt and silt mixed with either metakaolin or pulverised fuel ash (PFA). Silt geopolymers cured at room temperature had average 7-day compressive strengths of 18.7MPa, while partial substitution of silt by metakaolin or PFA increased average compressive strengths to 30.5 and 21.9MPa, respectively. Curing specimens for 24h at 105 degrees C resulted in a compressive strength of 39.7MPa and microstructural analysis confirmed the formation of dense materials. These strengths are in excess of those required for materials to be used as aggregate, particularly in unbound applications. The implications of this research for the management of waste silt at construction and demolition waste washing plants are discussed.

Lightning electromagnetic radiation field spectra in the interval from 0. 2 to 20 MHz

DOE Office of Scientific and Technical Information (OSTI.GOV)

Willett, J.C.; Bailey, J.C.; Leteinturier, C.

1990-11-20

Average energy spectral densities are presented for the fast transitions in most of the components that produce large radiation field impulses from cloud-to-ground lightning; first and subsequent return strokes; stepped, dart-stepped, and 'chaotic' leaders; and 'characteristic' cloud pulses. A disagreement in the previous literature about the spectral energy radiated by return strokes at high frequencies is noted and explained. The authors show that the spectral amplitudes are not seriously distorted by propagation over less than 35 km of seawater, although as much as 45 km of such propagation does appear to produce significant attenuation above about 10 MHz. First andmore » subsequent return strokes produce identical spectra between 0.2 and 20 MHz. The spectra of stepped and dart-stepped leader steps are nearly identical and are very similar to that of characteristic pulses. The spectra of leader steps also match return stroke spectra above 2-3 MHz after the former are increased by about 7 dB. The shapes of individual spectra do not depend on their amplitude, so the shapes of the average spectra are probably not distorted by the trigger thresholds used in the data acquisition. Return strokes are the strongest sources of radiation from cloud-to-ground lightning in the 0.2- to 20-MHz frequency range, although certain intracloud processes are stronger radiators above 8 MHz.« less

Fall may be imminent for Kansas Cherokee basin coalbed gas output

USGS Publications Warehouse

Newell, K. David

2010-01-01

Natural gas production in the Kansas portion of the Cherokee basin, Southeastern Kansas, for 2008 was 49.1 bcf. The great majority of Cherokee basin gas production is now coal-bed methane (CBM). The major producers are Quest Energy LLC, Dart Cherokee Basin Operating Co. LLC, and Layne Energy Operating LLC. Most CBM in Southeastern Kansas is from Middle and Upper Pennsylvanian high-volatile B and A rank bituminous coals at 800 to 1,200 ft depth. Rates of decline for the CBM wells generally decrease the longer a well produces. A gentler collective decline of 13.8% is calculated by averaging the number of new producing wells in a given year with that of the previous year. By the calculations using the gentler overall 13.8% decline rate, if more than 918 successful CBM wells are drilled in 2009, then gas production will increase from 2008 to 2009.

Monetary Shocks in Models with Inattentive Producers.

PubMed

Alvarez, Fernando E; Lippi, Francesco; Paciello, Luigi

2016-04-01

We study models where prices respond slowly to shocks because firms are rationally inattentive. Producers must pay a cost to observe the determinants of the current profit maximizing price, and hence observe them infrequently. To generate large real effects of monetary shocks in such a model the time between observations must be long and/or highly volatile. Previous work on rational inattentiveness has allowed for observation intervals that are either constant-but-long ( e.g . Caballero, 1989 or Reis, 2006) or volatile-but-short ( e.g . Reis's, 2006 example where observation costs are negligible), but not both. In these models, the real effects of monetary policy are small for realistic values of the duration between observations. We show that non-negligible observation costs produce both of these effects: intervals between observations are infrequent and volatile. This generates large real effects of monetary policy for realistic values of the average time between observations.

Analysis of Terrestrial Conditions and Dynamics

NASA Technical Reports Server (NTRS)

Goward, S. N.

1985-01-01

An ecological model is developed to estimate annual net primary productivity of vegetation in twelve major North American biomes. Three models are adapted and combined, each addressing a different factor known to govern primary productivity, i.e., photosynthesis, respiration, and moisture availability. Measures of intercepted photosynthetically active radiation (1PAR) for input to the photosynthesis model are derived from spectral vegetation index data. Normalized Difference Vegetation Index (NDVI) data are produced from NOAA-7 Advanced Very High Resolution Radiometer (AVHRR) observations for April 1982 through March 1983. NDVI values are sampled from within the biomes at locations for which climatological data are available. Monthly estimates of Net Primary Productivity (NPP) for each sample location are generated and summed over the twelve month period. These monthly estimates are averaged to produce a single annual estimated NPP value for each biomes. Comparison of estimated NPP values with figures reported in the literature produces a correlation coefficient of 85.

Observations of the initial stage of a rocket-and-wire-triggered lightning discharge

NASA Astrophysics Data System (ADS)

Zhang, Yang; Krehbiel, Paul R.; Zhang, Yijun; Lu, Weitao; Zheng, Dong; Xu, Liangtao; Huang, Zhigang

2017-05-01

Observations have been obtained of the initial stage of a rocket-and-wire-triggered lightning flash with a high-resolution broadband VHF interferometer. The discharge produced 54 precursor current pulses (PCPs) over 883 ms during the rocket's ascent. The interferometer observations show that the PCPs were produced by breakdown at the ascending tip of the rocket, and that individual PCPs were produced by weak upward positive breakdown over meters-scale distances, followed by more energetic, fast downward negative breakdown over several tens of meters distance. The average propagation speeds were 5 × 106 m s-1 and 3 × 107 m s-1, respectively. The sustained upward positive leader (UPL) was initiated by a rapid, repetitive burst of 14 precursor pulses. Upon initiation, the VHF radiation abruptly became continuous with time. Significantly, breakdown during the UPL appeared to extend the discharge in a similar manner to that of the precursor pulses.

Method and Apparatus for the Portable Identification of Material Thickness and Defects Using Spatially Controlled Heat Application

NASA Technical Reports Server (NTRS)

Cramer, K. Elliott (Inventor); Winfree, William P. (Inventor)

1999-01-01

A method and a portable apparatus for the nondestructive identification of defects in structures. The apparatus comprises a heat source and a thermal imager that move at a constant speed past a test surface of a structure. The thermal imager is off set at a predetermined distance from the heat source. The heat source induces a constant surface temperature. The imager follows the heat source and produces a video image of the thermal characteristics of the test surface. Material defects produce deviations from the constant surface temperature that move at the inverse of the constant speed. Thermal noise produces deviations that move at random speed. Computer averaging of the digitized thermal image data with respect to the constant speed minimizes noise and improves the signal of valid defects. The motion of thermographic equipment coupled with the high signal to noise ratio render it suitable for portable, on site analysis.

Monetary Shocks in Models with Inattentive Producers

PubMed Central

Alvarez, Fernando E.; Lippi, Francesco; Paciello, Luigi

2016-01-01

We study models where prices respond slowly to shocks because firms are rationally inattentive. Producers must pay a cost to observe the determinants of the current profit maximizing price, and hence observe them infrequently. To generate large real effects of monetary shocks in such a model the time between observations must be long and/or highly volatile. Previous work on rational inattentiveness has allowed for observation intervals that are either constant-but-long (e.g. Caballero, 1989 or Reis, 2006) or volatile-but-short (e.g. Reis's, 2006 example where observation costs are negligible), but not both. In these models, the real effects of monetary policy are small for realistic values of the duration between observations. We show that non-negligible observation costs produce both of these effects: intervals between observations are infrequent and volatile. This generates large real effects of monetary policy for realistic values of the average time between observations. PMID:27516627

Characterization of on-road CO, HC and NO emissions for petrol vehicle fleet in China city*

PubMed Central

Guo, Hui; Zhang, Qing-yu; Shi, Yao; Wang, Da-hui; Ding, Shu-ying; Yan, Sha-sha

2006-01-01

Vehicle emissions are a major source of air pollution in urban areas. The impact on urban air quality could be reduced if the trends of vehicle emissions are well understood. In the present study, the real-world emissions of vehicles were measured using a remote sensing system at five sites in Hangzhou, China from February 2004 to August 2005. More than 48000 valid gasoline powered vehicle emissions of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NO) were measured. The results show that petrol vehicle fleet in Hangzhou has considerably high CO emissions, with the average emission concentration of 2.71%±0.02%, while HC and NO emissions are relatively lower, with the average emission concentration of (153.72±1.16)×10−6 and (233.53±1.80)×10−6, respectively. Quintile analysis of both average emission concentration and total amount emissions by model year suggests that in-use emission differences between well maintained and badly maintained vehicles are larger than the age-dependent deterioration of emissions. In addition, relatively new high polluting vehicles are the greatest contributors to fleet emissions with, for example, 46.55% of carbon monoxide fleet emissions being produced by the top quintile high emitting vehicles from model years 2000~2004. Therefore, fleet emissions could be significantly reduced if new highly polluting vehicles were subject to effective emissions testing followed by appropriate remedial action. PMID:16773726

Treatment of poultry slaughterhouse wastewater using a static granular bed reactor (SGBR) coupled with ultrafiltration (UF) membrane system.

PubMed

Basitere, M; Rinquest, Z; Njoya, M; Sheldon, M S; Ntwampe, S K O

2017-07-01

The South African poultry industry has grown exponentially in recent years due to an increased demand for their products. As a result, poultry plants consume large volumes of high quality water to ensure that hygienically safe poultry products are produced. Furthermore, poultry industries generate high strength wastewater, which can be treated successfully at low cost using anaerobic digesters. In this study, the performance of a bench-scale mesophilic static granular bed reactor (SGBR) containing fully anaerobic granules coupled with an ultrafiltration (UF) membrane system, as a post-treatment system, was investigated. The poultry slaughterhouse wastewater was characterized by a chemical oxygen demand (COD) range between 1,223 and 9,695mg/L, average biological oxygen demand of 2,375mg/L and average fats, oil and grease (FOG) of 554mg/L. The SGBR anaerobic reactor was operated for 9 weeks at different hydraulic retention times (HRTs), i.e. 55 and 40 h, with an average organic loading rate (OLR) of 1.01 and 3.14g COD/L.day. The SGBR results showed an average COD, total suspended solids (TSS) and FOG removal of 93%, 95% and 90% respectively, for both OLR. The UF post-treatment results showed an average of COD, TSS and FOG removal of 64%, 88% and 48%, respectively. The overall COD, TSS and FOG removal of the system (SGBR and UF membrane) was 98%, 99.8%, and 92.4%, respectively. The results of the combined SGBR reactor coupled with the UF membrane showed a potential to ensure environmentally friendly treatment of poultry slaughterhouse wastewater.

Evaluating Non-potable Water Usage for Oil and Gas Purposes in the Permian Basin Using Reactive Transport Modeling

NASA Astrophysics Data System (ADS)

Marsac, K.; Navarre-Sitchler, A.

2017-12-01

Oil and gas company water usage is currently an area of concern in the water stressed western United States. 87% of recent wells in the Permian Basin are located in areas of high or extreme water stress. Using recycled produced water or groundwater that does not meet the USDW drinking water standards for oil and gas purposes could assist in relieving both water stress and tension between oil and gas companies and the public. However, non-USDW drinking water (TDS over 10,000 ppm) has the potential to react with formation water causing mineral precipitation, reducing the permeability of the producing formation. To evaluate the potential of non-potable water usage in the Permian Basin, available groundwater chemistry data was compiled into a database. Data was collected from the NETL-run NATCARB database, the USGS Produced Water and NWIS Databases, and the Texas Water Development Board. The created database went through a system of quality assurance and control for pH, TDS, depth and charge balance. Data was used to generate a set of waters representative of Permian Basin groundwater based on TDS, Ca/Mg ratio and Cl/SO4 ratio. Low, medium and high values of these three characteristics; representing the 25th, 50th and 75th percentile respectively; were used to create a matrix of 27 waters. Low TDS is 64,660 ppm, medium TDS is 98,486 ppm, and high TDS is 157,317 ppm. Ca/Mg ratios range from 1.98 to 7.26, and Cl/SO4 ratios range from 32.96 to 62.34. Results from mixing and titration models between these 27 waters and average Permian Basin water using Geochemist's Workbench show a maximum total precipitation of 1.815 cm3 in 1 L of water. In term of porosity, this represents a maximum porosity decrease due to mineral precipitation of 0.18%. This maximum precipitation scenario resulted from mixing average water with high TDS, high Ca/Mg ratio and low Cl/SO4 ratio water. We further investigate the impact of mineral precipitation on porosity and permeability using reactive transport modeling. A cylindrical, homogeneous PFLOTRAN reactive-transport model simulates the injection of high-TDS, high Ca/Mg, low Cl/SO4 water into the pay formation and the possible effects of precipitation over the lifetime of a well.

Low Cost Nuclear Thermal Rocket Cermet Fuel Element Environment Testing

NASA Technical Reports Server (NTRS)

Bradley, David E.; Mireles, Omar R.; Hickman, Robert R.

2011-01-01

Deep space missions with large payloads require high specific impulse (Isp) and relatively high thrust in order to achieve mission goals in reasonable time frames. Conventional, storable propellants produce average Isp. Nuclear thermal rockets (NTR) capable of high Isp thrust have been proposed. NTR employs heat produced by fission reaction to heat and therefore accelerate hydrogen which is then forced through a rocket nozzle providing thrust. Fuel element temperatures are very high (up to 3000K) and hydrogen is highly reactive with most materials at high temperatures. Data covering the effects of high temperature hydrogen exposure on fuel elements is limited. The primary concern is the mechanical failure of fuel elements which employ high-melting-point metals, ceramics or a combination (cermet) as a structural matrix into which the nuclear fuel is distributed. It is not necessary to include fissile material in test samples intended to explore high temperature hydrogen exposure of the structural support matrices. A small-scale test bed designed to heat fuel element samples via non-contact RF heating and expose samples to hydrogen is being developed to assist in optimal material and manufacturing process selection without employing fissile material. This paper details the test bed design and results of testing conducted to date.

Compact Fuel Element Environment Test

NASA Technical Reports Server (NTRS)

Bradley, D. E.; Mireles, O. R.; Hickman, R. R.; Broadway, J. W.

2012-01-01

Deep space missions with large payloads require high specific impulse (I(sub sp)) and relatively high thrust to achieve mission goals in reasonable time frames. Conventional, storable propellants produce average I(sub sp). Nuclear thermal rockets (NTRs) capable of high I(sub sp) thrust have been proposed. NTR employs heat produced by fission reaction to heat and therefore accelerate hydrogen, which is then forced through a rocket nozzle providing thrust. Fuel element temperatures are very high (up to 3,000 K) and hydrogen is highly reactive with most materials at high temperatures. Data covering the effects of high-temperature hydrogen exposure on fuel elements are limited. The primary concern is the mechanical failure of fuel elements that employ high melting point metals, ceramics, or a combination (cermet) as a structural matrix into which the nuclear fuel is distributed. It is not necessary to include fissile material in test samples intended to explore high-temperature hydrogen exposure of the structural support matrices. A small-scale test bed designed to heat fuel element samples via noncontact radio frequency heating and expose samples to hydrogen for typical mission durations has been developed to assist in optimal material and manufacturing process selection without employing fissile material. This Technical Memorandum details the test bed design and results of testing conducted to date.

Decline in placebo-controlled trial results suggests new directions for comparative effectiveness research.

PubMed

Olfson, Mark; Marcus, Steven C

2013-06-01

The Affordable Care Act offers strong support for comparative effectiveness research, which entails comparisons among active treatments, to provide the foundation for evidence-based practice. Traditionally, a key form of research into the effectiveness of therapeutic treatments has been placebo-controlled trials, in which a specified treatment is compared to placebo. These trials feature high-contrast comparisons between treatments. Historical trends in placebo-controlled trials have been evaluated to help guide the comparative effectiveness research agenda. We investigated placebo-controlled trials reported in four leading medical journals between 1966 and 2010. We found that there was a significant decline in average effect size or average difference in efficacy (the ability to produce a desired effect) between the active treatment and placebo. On average, recently studied treatments offered only small benefits in efficacy over placebo. A decline in effect sizes in conventional placebo-controlled trials supports an increased emphasis on other avenues of research, including comparative studies on the safety, tolerability, and cost of treatments with established efficacy.

Photo-Realistic Statistical Skull Morphotypes: New Exemplars for Ancestry and Sex Estimation in Forensic Anthropology.

PubMed

Caple, Jodi; Stephan, Carl N

2017-05-01

Graphic exemplars of cranial sex and ancestry are essential to forensic anthropology for standardizing casework, training analysts, and communicating group trends. To date, graphic exemplars have comprised hand-drawn sketches, or photographs of individual specimens, which risks bias/subjectivity. Here, we performed quantitative analysis of photographic data to generate new photo-realistic and objective exemplars of skull form. Standardized anterior and left lateral photographs of skulls for each sex were analyzed in the computer graphics program Psychomorph for the following groups: South African Blacks, South African Whites, American Blacks, American Whites, and Japanese. The average cranial form was calculated for each photographic view, before the color information for every individual was warped to the average form and combined to produce statistical averages. These mathematically derived exemplars-and their statistical exaggerations or extremes-retain the high-resolution detail of the original photographic dataset, making them the ideal casework and training reference standards. © 2016 American Academy of Forensic Sciences.

The production of calibration specimens for impact testing of subsize Charpy specimens

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alexander, D.J.; Corwin, W.R.; Owings, T.D.

1994-09-01

Calibration specimens have been manufactured for checking the performance of a pendulum impact testing machine that has been configured for testing subsize specimens, both half-size (5.0 {times} 5.0 {times} 25.4 mm) and third-size (3.33 {times} 3.33 {times} 25.4 mm). Specimens were fabricated from quenched-and-tempered 4340 steel heat treated to produce different microstructures that would result in either high or low absorbed energy levels on testing. A large group of both half- and third-size specimens were tested at {minus}40{degrees}C. The results of the tests were analyzed for average value and standard deviation, and these values were used to establish calibration limitsmore » for the Charpy impact machine when testing subsize specimens. These average values plus or minus two standard deviations were set as the acceptable limits for the average of five tests for calibration of the impact testing machine.« less

1W frequency-doubled VCSEL-pumped blue laser with high pulse energy

NASA Astrophysics Data System (ADS)

Van Leeuwen, Robert; Chen, Tong; Watkins, Laurence; Xu, Guoyang; Seurin, Jean-Francois; Wang, Qing; Zhou, Delai; Ghosh, Chuni

2015-02-01

We report on a Q-switched VCSEL side-pumped 946 nm Nd:YAG laser that produces high average power blue light with high pulse energy after frequency doubling in BBO. The gain medium was water cooled and symmetrically pumped by three 1 kW 808 nm VCSEL pump modules. More than 1 W blue output was achieved at 210 Hz with 4.9 mJ pulse energy and at 340 Hz with 3.2 mJ pulse energy, with 42% and 36% second harmonic conversion efficiency respectively. Higher pulse energy was obtained at lower repetition frequencies, up to 9.3 mJ at 70 Hz with 52% conversion efficiency.

From Kuiper Belt to Comet: The Shapes of the Nuclei

NASA Astrophysics Data System (ADS)

Jewitt, D.; Sheppard, S.; Fernandez, Y.

2003-05-01

It is widely believed that escaped objects from the Kuiper Belt are the source of both the Centaurs and the nuclei of the Jupiter Family Comets (JFCs). If the JFC nuclei are produced by collisional breakup of parent objects in the Kuiper Belt, then it is reasonable to expect that their shape distribution should be consistent with those of fragments produced in disintegrative laboratory experiments, or with the small main-belt asteroids (which are produced collisionally). We test this idea using a sample of eleven well-observed cometary nuclei. Our main result is that the nuclei are, on average, much more elongated than either the collisionally produced small main-belt asteroids or the fragments created in laboratory impact experiments. Several interpretations of this systematic shape difference are possible (including the obvious one that the JFC nuclei are not, after all, produced collisionally in the Kuiper Belt). Our preferred explanation, however, is that the asphericities of the nuclei have been modified by one or more processes of mass loss. An implication of this interpretation is that the JFC nuclei in our sample are highly evolved, having lost a major part of their original mass. In turn, this implies that the angular momenta of the nuclei are also non-primordial: the JFC nuclei are highly physically evolved objects. We will discuss the evidence supporting these conclusions. This work has been recently published in Astronomical Journal, 125, 3366-3377 (2003).

40 CFR 63.494 - Back-end process provisions-residual organic HAP and emission limitations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... produced by the emulsion process, polybutadiene rubber and styrene butadiene rubber produced by the... styrene butadiene rubber produced by the emulsion process: (i) A monthly weighted average of 0.40 kg... than a solution or emulsion process, polybutadiene rubber produced by any process other than a solution...

Impact of US and Canadian precursor regulation on methamphetamine purity in the United States.

PubMed

Cunningham, James K; Liu, Lon-Mu; Callaghan, Russell

2009-03-01

Reducing drug purity is a major, but largely unstudied, goal of drug suppression. This study examines whether US methamphetamine purity was impacted by the suppression policy of US and Canadian precursor chemical regulation. Autoregressive integrated moving average (ARIMA)-intervention time-series analysis. Continental United States and Hawaii (1985-May 2005). Interventions US federal regulations targeting precursors, ephedrine and pseudoephedrine, in forms used by large-scale producers were implemented in November 1989, August 1995 and October 1997. US regulations targeting precursors in forms used by small-scale producers (e.g. over-the-counter medications) were implemented in October 1996 and October 2001. Canada implemented federal precursor regulations in January 2003 and July 2003 and an essential chemical (e.g. acetone) regulation in January 2004. Monthly median methamphetamine purity series. US regulations targeting large-scale producers were associated with purity declines of 16-67 points; those targeting small-scale producers had little or no impact. Canada's precursor regulations were associated with purity increases of 13-15 points, while its essential chemical regulation was associated with a 13-point decrease. Hawaii's purity was consistently high, and appeared to vary little with the 1990s/2000s regulations. US precursor regulations targeting large-scale producers were associated with substantial decreases in continental US methamphetamine purity, while regulations targeting over-the-counter medications had little or no impact. Canada's essential chemical regulation was also associated with a decrease in continental US purity. However, Canada's precursor regulations were associated with purity increases: these regulations may have impacted primarily producers of lower-quality methamphetamine, leaving higher-purity methamphetamine on the market by default. Hawaii's well-known preference for 'ice' (high-purity methamphetamine) may have helped to constrain purity there to a high, attenuated range, possibly limiting its sensitivity to precursor regulation.

40 CFR 421.265 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... day Maximum for monthly average mg/troy ounce of precious metals, including silver, incinerated or... Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average mg/troy ounce of precious... Maximum for any 1 day Maximum for monthly average mg/troy ounce of gold produced by cyanide stripping...

Formation of TiO2 nanotube arrays in KOH added fluoride-ethylene glycol (EG) electrolyte and its photoelectrochemical response

NASA Astrophysics Data System (ADS)

Nyein, Nyein; Lockman, Zainovia; Matsuda, Astunori; Kawamura, Go; Tan, Wai Kian; Oo, Than Zaw

2016-07-01

In this study, highly ordered TiO2 nanotube arrays were prepared by anodic oxidation of titanium foil in fluoride -EG electrolyte containing a small amount of potassium hydroxide, KOH at 60 V for 30 min. This electrolyte resulted in the formation of long nanotubes with an average length of 10 µm and diameter of 170 nm. For comparison, TiO2 nanotubes anodized in H2O added EG electrolyte which produces short nanotubes with an average tube length of 5 µm and diameter of 170 nm. It appears that the addition of KOH into the fluoride EG electrolyte accelerated the formation of the TiO2 nanotubes as it is believed that the chemical dissolution at the tips of the nanotubes is suppressed. Highly ordered TiO2 nanotubes anodized in KOH added EG electrolyte exhibited the photocurrent density of 2 mA/cm2, which is significantly higher than H2O added sample (1.5 mA/cm2).

Communal Sharing and the Provision of Low-Volume High-Cost Health Services: Results of a Survey.

PubMed

Richardson, Jeff; Iezzi, Angelo; Chen, Gang; Maxwell, Aimee

2017-03-01

This paper suggests and tests a reason why the public might support the funding of services for rare diseases (SRDs) when the services are effective but not cost effective, i.e. when more health could be produced by allocating funds to other services. It is postulated that the fairness of funding a service is influenced by a comparison of the average patient benefit with the average cost to those who share the cost. Survey respondents were asked to allocate a budget between cost-effective services that had a small effect upon a large number of relatively well patients and SRDs that benefited a small number of severely ill patients but were not cost effective because of their high cost. Part of the budget was always allocated to the SRDs. The budget share rose with the number sharing the cost. Sharing per se appears to characterise preferences. This has been obscured in studies that focus upon cost per patient rather than cost per person sharing the cost.

Facile fabrication of silver nanoparticles with temperature-responsive sizes as highly active SERS substrates

NASA Astrophysics Data System (ADS)

Wu, Jing; Fang, Jinghuai; Cheng, Mingfei; Gong, Xiao

2016-12-01

In our work, large-scale silver NPs (nanoparticles) are successfully synthesized on zinc foils with controllable size by regulating the temperature of the displacement reaction. Our results show that when the temperature is 70 °C, the average size of silver NPs is approximately 88 nm in diameter, and they exhibit the strongest SERS activity. The gap between nanoparticles is simultaneously regulated as near as possible, which produces abundant "hot spots" and nanogaps. Crystal violet (CV) was used as probe molecules, and the SERS signals show that the values of relative standard deviation in the intensity of the main vibration modes are less than 10%, demonstrating excellent reproducibility of the silver NPs. Furthermore, the high surface-average enhancement factor of 3.86 × 107 is achieved even when the concentration of CV is 10-7 M, which is sufficient for single-molecule detection. We believe that this low cost and rapid route would get wide applications in chemical synthesis.

Comparisons of observed seasonal climate features with a winter and summer numerical simulation produced with the GLAS general circulation model

NASA Technical Reports Server (NTRS)

Halem, M.; Shukla, J.; Mintz, Y.; Wu, M. L.; Godbole, R.; Herman, G.; Sud, Y.

1979-01-01

Results are presented from numerical simulations performed with the general circulation model (GCM) for winter and summer. The monthly mean simulated fields for each integration are compared with observed geographical distributions and zonal averages. In general, the simulated sea level pressure and upper level geopotential height field agree well with the observations. Well simulated features are the winter Aleutian and Icelandic lows, the summer southwestern U.S. low, the summer and winter oceanic subtropical highs in both hemispheres, and the summer upper level Tibetan high and Atlantic ridge. The surface and upper air wind fields in the low latitudes are in good agreement with the observations. The geographical distirbutions of the Earth-atmosphere radiation balance and of the precipitation rates over the oceans are well simulated, but not all of the intensities of these features are correct. Other comparisons are shown for precipitation along the ITCZ, rediation balance, zonally averaged temperatures and zonal winds, and poleward transports of momentum and sensible heat.

A statistical approach to rank multiple priorities in environmental epidemiology: an example from high-risk areas in Sardinia, Italy.

PubMed

Catelan, Dolores; Biggeri, Annibale

2008-11-01

In environmental epidemiology, long lists of relative risk estimates from exposed populations are compared to a reference to scrutinize the dataset for extremes. Here, inference on disease profiles for given areas, or for fixed disease population signatures, are of interest and summaries can be obtained averaging over areas or diseases. We have developed a multivariate hierarchical Bayesian approach to estimate posterior rank distributions and we show how to produce league tables of ranks with credibility intervals useful to address the above mentioned inferential problems. Applying the procedure to a real dataset from the report "Environment and Health in Sardinia (Italy)" we selected 18 areas characterized by high environmental pressure for industrial, mining or military activities investigated for 29 causes of deaths among male residents. Ranking diseases highlighted the increased burdens of neoplastic (cancerous), and non-neoplastic respiratory diseases in the heavily polluted area of Portoscuso. The averaged ranks by disease over areas showed lung cancer among the three highest positions.

High-pulse-energy mode-locked picosecond oscillator

NASA Astrophysics Data System (ADS)

Chao, Yang; Chen, Meng; Li, Gang

2014-02-01

We report on a high-pulse-energy solid-state picosecond Nd:YVO4 oscillator with cavity-dumping. The laser is end-pumped by an 808 nm laser diode and passively mode-locked with a semiconductor saturable absorption mirror (SESAM). In pure cw-mode-locking, this laser produced 2.5 W of average power at a pulse repetition rate of 40 MHz and pulse duration around 12 ps. A cavity dumping technique using an intra-cavity BBO electro-optic crystal to which bidirectional voltage was applied was adopted, effectively improving the cavity-dumping rate. Tunable high repetition rate from 100 kHz to 1 MHz was achieved. With electro-optic cavity dumper working at 1 MHz repetition rate, we achieved average power 594 mW. The laser includes a 5 mm long, a-cut, 0.5% doped Nd:YVO4 crystal with a 5-degree angle at one end face. Laser radiation is coupled out from the crystal end face with a 5-degree angle, without requiring insertion of a thin-film polarizer (TFP), thus simplifying the laser structure. This picosecond laser system has the advantages of compact structure and high stability, providing a good oscillator for regenerative amplifiers.

The optimization of fermentation conditions for producing cellulase of Bacillus amyloliquefaciens and its application to goose feed

PubMed Central

Ye, Miao; Sun, Linghong; Yang, Ru; Qi, KeZong

2017-01-01

The proper culture conditions for producing cellulase of Bacillus amyloliquefaciens S1, isolated from the cecum of goose was optimized by single-factor experiment combined with orthogonal test. The properties of the cellulase were investigated by DNS method. The appropriate doses of B. amyloliquefaciens S1 were obtained by adding them to goose feed. It indicated that the suitable culture conditions of producing cellulase were the culture temperature of 37°C, the initial pH of 7.0, the incubation time of 72 h and the loaded liquid volume of 75 ml per 250 ml. The effects of each factor on producing cellulase by B. amyloliquefaciens S1 were as follows: initial pH > incubation time = culture temperature > loaded liquid volume. The optimum reaction temperature and pH were 50°C and 7.0, respectively. This enzyme is a kind of neutral cellulase that possesses resistance to heat and acidity. It showed high activity to absorbent cotton, soya bean meal and filter paper. By adding different doses of B. amyloliquefaciens S1 to the goose feed, it was found that the egg production, average egg weight, fertilization rate and the hatching rate were promoted both in experiment 1 (1.5 g kg−1) and experiment 2 (3 g kg−1). Also the difference of egg production, fertilization rate and hatching rate between experiment 1 and control group was obvious (p < 0.05), and the average egg weight was significantly increased in experiment 2 (p < 0.05). PMID:29134097

A highly efficient protocol for micropropagation of Begonia tuberous.

PubMed

Duong, Tan Nhut; Nguyen, Thanh Hai; Mai, Xuan Phan

2010-01-01

A protocol for micropropagation of begonia was established utilizing a thin cell layer (TCL) system. This system has been employed to produce several thousand shoots per sample. Explant size and position, and plant growth regulators (PGRs) contribute to the tissue morphogenesis. By optimizing the size of the tissue and applying an improved selection procedure, shoots were elongated in 8 weeks of culture, with an average number of 210 +/- 9.7 shoots per segment. This system has facilitated a number of studies using TCL as a model for micropropagation and will enable the large-scale production of begonia. On an average, the best treatment would allow production of about 10,000 plantlets by the micropropagation of the axillary buds of one plant with five petioles, within a period of 8 months.

Effect of scene illumination conditions on digital enhancement techniques of multispectral scanner LANDSAT images

NASA Technical Reports Server (NTRS)

Parada, N. D. J.; Novo, E. M. L. M.

1983-01-01

Two sets of MSS/LANDSAT data with solar elevation ranging from 22 deg to 41 deg were used at the Image-100 System to implement the Eliason et alii technique for extracting the topographic modulation component. An unsupervised cluster analysis was used to obtain an average brightness image for each channel. Analysis of the enhanced imaged shows that the technique for extracting topographic modulation component is more appropriated to MSS data obtained under high sun elevation ngles. Low sun elevation increases the variance of each cluster so that the average brightness doesn't represent its albedo proprties. The topographic modulation component applied to low sun elevation angle damages rather than enhance topographic information. Better results were produced for channels 4 and 5 than for channels 6 and 7.

Nutritive value of selected variety breads and pastas.

PubMed

Ranhotra, G S; Gelroth, J A; Novak, F A; Bock, M A; Winterringer, G L; Matthews, R H

1984-03-01

Nine types of commercially produced variety breads, plain bagels, corn tortillas, and three types of pasta products were obtained from each of four cities, New York, San Francisco, Atlanta, and Kansas City. Proximate components and 12 minerals and vitamins were determined in these and in cooked pasta products. Available carbohydrate and energy values were calculated. On the average, French, Italian, and pita breads were lower in moisture than other breads. Protein in bread products averaged between 7.6% and 10.4% and in cooked pastas and tortillas between 4.4% and 5.3%. Bagels averaged 10.2% protein. Insoluble dietary fiber in whole wheat bread averaged 5.6%; for most products, dietary fiber values were five- to eightfold higher than crude fiber values. Pasta products and tortillas were virtually free of sodium. Sodium in bread products averaged between 379 and 689 mg/100 gm. Although all pasta products and most bread products were enriched, calcium was often not included. Iron averaged from 2.16 to 3.29 mg/100 gm in bread products and 3.10 to 4.24 mg/100 gm in dry pasta products. Products made with unrefined or less-refined flours and/or containing germ and bran tended to be high in phosphorus, magnesium, zinc, and manganese, and, to a lesser extent, in copper. A good portion of potassium, thiamin, riboflavin, and niacin in pasta products was lost during cooking.

Optimization and characterization of high pressure homogenization produced chemically modified starch nanoparticles.

PubMed

Ding, Yongbo; Kan, Jianquan

2017-12-01

Chemically modified starch (RS4) nanoparticles were synthesized through homogenization and water-in-oil mini-emulsion cross-linking. Homogenization was optimized with regard to z-average diameter by using a three-factor-three-level Box-Behnken design. Homogenization pressure (X 1 ), oil/water ratio (X 2 ), and surfactant (X 3 ) were selected as independent variables, whereas z-average diameter was considered as a dependent variable. The following optimum preparation conditions were obtained to achieve the minimum average size of these nanoparticles: 50 MPa homogenization pressure, 10:1 oil/water ratio, and 2 g surfactant amount, when the predicted z-average diameter was 303.6 nm. The physicochemical properties of these nanoparticles were also determined. Dynamic light scattering experiments revealed that RS4 nanoparticles measuring a PdI of 0.380 and an average size of approximately 300 nm, which was very close to the predicted z-average diameter (303.6 nm). The absolute value of zeta potential of RS4 nanoparticles (39.7 mV) was higher than RS4 (32.4 mV), with strengthened swelling power. X-ray diffraction results revealed that homogenization induced a disruption in crystalline structure of RS4 nanoparticles led to amorphous or low-crystallinity. Results of stability analysis showed that RS4 nanosuspensions (particle size) had good stability at 30 °C over 24 h.

40 CFR 421.303 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... pounds) of TiCl4 produced Chromium (total) 0.346 0.140 Lead 0.262 0.122 Nickel 0.515 0.346 Titanium 0.496... average mg/kg (pounds per million pounds) of TiCl4 produced Chromium (total) 0.385 0.156 Lead 0.291 0.135... Maximum for monthly average mg/kg (pounds per million pounds) of TiCl4 handled Chromium (total) 0.069 0...

40 CFR 421.303 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... pounds) of TiCl4 produced Chromium (total) 0.346 0.140 Lead 0.262 0.122 Nickel 0.515 0.346 Titanium 0.496... average mg/kg (pounds per million pounds) of TiCl4 produced Chromium (total) 0.385 0.156 Lead 0.291 0.135... Maximum for monthly average mg/kg (pounds per million pounds) of TiCl4 handled Chromium (total) 0.069 0...

40 CFR 421.303 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... pounds) of TiCl4 produced Chromium (total) 0.346 0.140 Lead 0.262 0.122 Nickel 0.515 0.346 Titanium 0.496... average mg/kg (pounds per million pounds) of TiCl4 produced Chromium (total) 0.385 0.156 Lead 0.291 0.135... Maximum for monthly average mg/kg (pounds per million pounds) of TiCl4 handled Chromium (total) 0.069 0...

Uranium silicide pellet fabrication by powder metallurgy for accident tolerant fuel evaluation and irradiation

DOE PAGES

Harp, Jason Michael; Lessing, Paul Alan; Hoggan, Rita Elaine

2015-06-21

In collaboration with industry, Idaho National Laboratory is investigating uranium silicide for use in future light water reactor fuels as a more accident resistant alternative to uranium oxide base fuels. Specifically this project was focused on producing uranium silicide (U 3Si 2) pellets by conventional powder metallurgy with a density greater than 94% of the theoretical density. This work has produced a process to consistently produce pellets with the desired density through careful optimization of the process. Milling of the U 3Si 2 has been optimized and high phase purity U 3Si 2 has been successfully produced. Results are presentedmore » from sintering studies and microstructural examinations that illustrate the need for a finely ground reproducible particle size distribution in the source powder. The optimized process was used to produce pellets for the Accident Tolerant Fuel-1 irradiation experiment. The average density of these pellets was 11.54 ±0.06 g/cm 3. Additional characterization of the pellets by scaning electron microscopy and X-ray diffraction has also been performed. As a result, pellets produced in this work have been encapsulated for irradiation, and irradiation in the Advanced Test Reactor is expected soon.« less

Uranium silicide pellet fabrication by powder metallurgy for accident tolerant fuel evaluation and irradiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harp, Jason Michael; Lessing, Paul Alan; Hoggan, Rita Elaine

In collaboration with industry, Idaho National Laboratory is investigating uranium silicide for use in future light water reactor fuels as a more accident resistant alternative to uranium oxide base fuels. Specifically this project was focused on producing uranium silicide (U 3Si 2) pellets by conventional powder metallurgy with a density greater than 94% of the theoretical density. This work has produced a process to consistently produce pellets with the desired density through careful optimization of the process. Milling of the U 3Si 2 has been optimized and high phase purity U 3Si 2 has been successfully produced. Results are presentedmore » from sintering studies and microstructural examinations that illustrate the need for a finely ground reproducible particle size distribution in the source powder. The optimized process was used to produce pellets for the Accident Tolerant Fuel-1 irradiation experiment. The average density of these pellets was 11.54 ±0.06 g/cm 3. Additional characterization of the pellets by scaning electron microscopy and X-ray diffraction has also been performed. As a result, pellets produced in this work have been encapsulated for irradiation, and irradiation in the Advanced Test Reactor is expected soon.« less

Bioavailability of modified-release methylphenidate: influence of high-fat breakfast when administered intact and when capsule content sprinkled on applesauce.

PubMed

Lee, Lucy; Kepple, Joanne; Wang, Yibin; Freestone, Stephen; Bakhtiar, Ray; Wang, Yanfeng; Hossain, Mohammad

2003-09-01

Ritalin, an immediate release form of racemic methylphenidate hydrochloride, has been available in the USA since 1955 and is used for the treatment of ADHD. The objective of this study was to evaluate the pharmacokinetics of modified-release methylphenidate (highest single dose), Ritalin LA, when administered under fasting condition, with a high-fat breakfast, and when sprinkled on applesauce in healthy adult subjects. Blood samples were drawn for 24 h following a 40 mg oral administration. Most subjects appeared to produce a bimodal methylphenidate plasma concentration profile. In all three treatment groups, methylphenidate was rapidly absorbed with an initial average t(max(0-4)) of 1.3-2.4 h and an average peak plasma concentration [C(max(abs))] of 14.4-15.2 ng/ml. On average, both the rate [C(max(abs)) and t(max(abs))] and the extent of absorption (AUC(0- infinity)) of methylphenidate were similar when the capsule was given with a high fat breakfast and when the capsule contents were sprinkled onto applesauce, compared with the fasting state. No dose dumping was observed when the capsule was given with a high fat breakfast or when sprinkled onto applesauce. The dose was safe and generally well tolerated. Coadministration of a single oral dose of 40 mg methylphenidate capsule whether administered intact with a high-fat breakfast or sprinkled on applesauce did not affect the overall rate or extent of absorption of methylphenidate compared with the fasted condition. Copyright 2003 John Wiley & Sons, Ltd.

Replicating cluster subtypes for the prevention of adolescent smoking and alcohol use.

PubMed

Babbin, Steven F; Velicer, Wayne F; Paiva, Andrea L; Brick, Leslie Ann D; Redding, Colleen A

2015-01-01

Substance abuse interventions tailored to the individual level have produced effective outcomes for a wide variety of behaviors. One approach to enhancing tailoring involves using cluster analysis to identify prevention subtypes that represent different attitudes about substance use. This study applied this approach to better understand tailored interventions for smoking and alcohol prevention. Analyses were performed on a sample of sixth graders from 20 New England middle schools involved in a 36-month tailored intervention study. Most adolescents reported being in the Acquisition Precontemplation (aPC) stage at baseline: not smoking or not drinking and not planning to start in the next six months. For smoking (N=4059) and alcohol (N=3973), each sample was randomly split into five subsamples. Cluster analysis was performed within each subsample based on three variables: Pros and Cons (from Decisional Balance Scales), and Situational Temptations. Across all subsamples for both smoking and alcohol, the following four clusters were identified: (1) Most Protected (MP; low Pros, high Cons, low Temptations); (2) Ambivalent (AM; high Pros, average Cons and Temptations); (3) Risk Denial (RD; average Pros, low Cons, average Temptations); and (4) High Risk (HR; high Pros, low Cons, and very high Temptations). Finding the same four clusters within aPC for both smoking and alcohol, replicating the results across the five subsamples, and demonstrating hypothesized relations among the clusters with additional external validity analyses provide strong evidence of the robustness of these results. These clusters demonstrate evidence of validity and can provide a basis for tailoring interventions. Copyright © 2014. Published by Elsevier Ltd.

Replicating cluster subtypes for the prevention of adolescent smoking and alcohol use

PubMed Central

Babbin, Steven F.; Velicer, Wayne F.; Paiva, Andrea L.; Brick, Leslie Ann D.; Redding, Colleen A.

2015-01-01

Introduction Substance abuse interventions tailored to the individual level have produced effective outcomes for a wide variety of behaviors. One approach to enhancing tailoring involves using cluster analysis to identify prevention subtypes that represent different attitudes about substance use. This study applied this approach to better understand tailored interventions for smoking and alcohol prevention. Methods Analyses were performed on a sample of sixth graders from 20 New England middle schools involved in a 36-month tailored intervention study. Most adolescents reported being in the Acquisition Precontemplation (aPC) stage at baseline: not smoking or not drinking and not planning to start in the next six months. For smoking (N= 4059) and alcohol (N= 3973), each sample was randomly split into five subsamples. Cluster analysis was performed within each subsample based on three variables: Pros and Cons (from Decisional Balance Scales), and Situational Temptations. Results Across all subsamples for both smoking and alcohol, the following four clusters were identified: (1) Most Protected (MP; low Pros, high Cons, low Temptations); (2) Ambivalent (AM; high Pros, average Cons and Temptations); (3) Risk Denial (RD; average Pros, low Cons, average Temptations); and (4) High Risk (HR; high Pros, low Cons, and very high Temptations). Conclusions Finding the same four clusters within aPC for both smoking and alcohol, replicating the results across the five subsamples, and demonstrating hypothesized relations among the clusters with additional external validity analyses provide strong evidence of the robustness of these results. These clusters demonstrate evidence of validity and can provide a basis for tailoring interventions. PMID:25222849

Implementation and validation of a CubeSat laser transmitter

NASA Astrophysics Data System (ADS)

Kingsbury, R. W.; Caplan, D. O.; Cahoy, K. L.

2016-03-01

The paper presents implementation and validation results for a CubeSat-scale laser transmitter. The master oscillator power amplifier (MOPA) design produces a 1550 nm, 200mW average power optical signal through the use of a directly modulated laser diode and a commercial fiber amplifier. The prototype design produces high-fidelity M-ary pulse position modulated (PPM) waveforms (M=8 to 128), targeting data rates > 10 Mbit/s while meeting a constraining 8W power allocation. We also present the implementation of an avalanche photodiode (APD) receiver with measured transmitter-to-receiver performance within 3 dB of theory. Via loopback, the compact receiver design can provide built-in self-test and calibration capabilities, and supports incremental on-orbit testing of the design.

Papaya (Carica papaya L.).

PubMed

Zhu, Yun J; Fitch, Maureen M M; Moore, Paul H

2006-01-01

Transgenic papaya plants were initially obtained using particle bombardment, a method having poor efficiency in producing intact, single-copy insertion of transgenes. Single-copy gene insertion was improved using Agrobacterium tumefaciens. With progress being made in genome sequencing and gene discovery, there is a need for more efficient methods of transformation in order to study the function of these genes. We describe a protocol for Agrobacterium-mediated transformation using carborundum-wounded papaya embryogenic calli. This method should lead to high-throughput transformation, which on average produced at least one plant that was positive in polymerase chain reaction (PCR), histochemical staining, or by Southern blot hybridization from 10 to 20% of the callus clusters that had been co-cultivated with Agrobacterium. Plants regenerated from the callus clusters in 9 to 13 mo.

Prevalence of lameness in high-producing holstein cows housed in freestall barns in Minnesota.

PubMed

Espejo, L A; Endres, M I; Salfer, J A

2006-08-01

A cross-sectional study was conducted to estimate the prevalence of clinical lameness in high-producing Holstein cows housed in 50 freestall barns in Minnesota during summer. Locomotion and body condition scoring were performed on a total of 5,626 cows in 53 high-production groups. Cow records were collected from the nearest Dairy Herd Improvement Association test date, and herd characteristics were collected at the time of the visit. The mean prevalence of clinical lameness (proportion of cows with locomotion score >or=3 on a 1-to-5 scale, where 1 = normal and 5 = severely lame), and its association with lactation number, month of lactation, body condition score, and type of stall surface were evaluated. The mean prevalence of clinical lameness was 24.6%, which was 3.1 times greater, on average, than the prevalence estimated by the herd managers on each farm. The prevalence of lameness in first-lactation cows was 12.8% and prevalence increased on average at a rate of 8 percentage units per lactation. There was no association between the mean prevalence of clinical lameness and month of lactation (for months 1 to 10). Underconditioned cows had a higher prevalence of clinical lameness than normal or overconditioned cows. The prevalence of lameness was lower in freestall herds with sand stalls (17.1%) than in freestall herds with mattress stall surfaces (27.9%). Data indicate that the best 10th percentile of dairy farms had a mean prevalence of lameness of 5.4% with only 1.47% of cows with locomotion score = 4 and no cows with locomotion score = 5.

Evaluation of Near-Tropopause Ozone Distributions in the Global Modeling Initiative Combined Stratosphere/Troposphere Model with Ozonesonde Data

NASA Technical Reports Server (NTRS)

Considine, David B.; Logan, Jennifer A.; Olsen, Mark A.

2008-01-01

The NASA Global Modeling Initiative has developed a combined stratosphere/troposphere chemistry and transport model which fully represents the processes governing atmospheric composition near the tropopause. We evaluate model ozone distributions near the tropopause, using two high vertical resolution monthly mean ozone profile climatologies constructed with ozonesonde data, one by averaging on pressure levels and the other relative to the thermal tropopause. Model ozone is high biased at the SH tropical and NH midlatitude tropopause by approx. 45% in a 4 deg. latitude x 5 deg. longitude model simulation. Increasing the resolution to 2 deg. x 2.5 deg. increases the NH tropopause high bias to approx. 60%, but decreases the tropical tropopause bias to approx. 30%, an effect of a better-resolved residual circulation. The tropopause ozone biases appear not to be due to an overly vigorous residual circulation or excessive stratosphere/troposphere exchange, but are more likely due to insufficient vertical resolution or excessive vertical diffusion near the tropopause. In the upper troposphere and lower stratosphere, model/measurement intercomparisons are strongly affected by the averaging technique. NH and tropical mean model lower stratospheric biases are less than 20%. In the upper troposphere, the 2 deg. x 2.5 deg. simulation exhibits mean high biases of approx. 20% and approx. 35% during April in the tropics and NH midlatitudes, respectively, compared to the pressure averaged climatology. However, relative-to-tropopause averaging produces upper troposphere high biases of approx. 30% and 70% in the tropics and NH midlatitudes. This is because relative-to-tropopause averaging better preserves large cross-tropopause O3 gradients, which are seen in the daily sonde data, but not in daily model profiles. The relative annual cycle of ozone near the tropopause is reproduced very well in the model Northern Hemisphere midlatitudes. In the tropics, the model amplitude of the near tropopause annual cycle is weak. This is likely due to the annual amplitude of mean vertical upwelling near the tropopause, which analysis suggests is approx. 30% weaker than in the real atmosphere.

Sublethal and Reproductive Effects of Acute and Chronic Exposure to Flowback and Produced Water from Hydraulic Fracturing on the Water Flea Daphnia magna.

PubMed

Blewett, Tamzin A; Delompré, Perrine L M; He, Yuhe; Folkerts, Erik J; Flynn, Shannon L; Alessi, Daniel S; Goss, Greg G

2017-03-07

Hydraulic fracturing is an industrial process allowing for the extraction of gas or oil. To fracture the rocks, a proprietary mix of chemicals is injected under high pressure, which later returns to the surface as flowback and produced water (FPW). FPW is a complex chemical mixture consisting of trace metals, organic compounds, and often, high levels of salts. FPW toxicity to the model freshwater crustacean Daphnia magna was characterized utilizing acute (48 h median lethal concentrations; LC 50 ) and chronic (21 day) exposures. A decrease in reproduction was observed, with a mean value of 18.5 neonates produced per replicate over a 21 day chronic exposure to 0.04% FPW, which was a significant decrease from the average of 64 neonates produced in the controls. The time to first brood was delayed in the highest FPW (0.04%) treatment. Neonates exhibited an LC 50 of 0.19% of full-strength FPW, making them more sensitive than adults, which displayed an LC 50 value of 0.75%. Quantitative PCR highlighted significant changes in expression of genes encoding xenobiotic metabolism (cyp4) and moulting (cut). This study is the first to characterize chronic FPW toxicity and will help with the development of environmental monitoring and risk assessment of FPW spills.

Storm surges and coastal impacts at Mar del Plata, Argentina

NASA Astrophysics Data System (ADS)

Fiore, Mónica M. E.; D'Onofrio, Enrique E.; Pousa, Jorge L.; Schnack, Enrique J.; Bértola, Germán R.

2009-07-01

Positive storm surges (PSS) lasting for several days can raise the water level producing significant differences between the observed level and the astronomical tide. These storm events can be more severe if they coincide with a high tide or if they bracket several tidal cycles, particularly in the case of the highest astronomical tide. Besides, the abnormal sea-level elevation near the coast can cause the highest waves generated to attack the upper beach. This combination of factors can produce severe erosion, threatening sectors located along the coastline. These effects would be more serious if the storm surge height and duration increase as a result of a climatic change. The Mar del Plata (Argentina) coastline and adjacent areas are exposed to such effects. A statistical characterization of PSS based on their intensity, duration and frequency, including a surge event classification, was performed utilizing tide-gauge records over the period 1956-2005. A storm erosion potential index (SEPI) was calculated from observed levels based on hourly water level measurements. The index was related to beach profile responses to storm events. Also, a return period for extreme SEPI values was calculated. Results show an increase in the average number of positive storm surge events per decade. Considering all the events, the last decade (1996-2005) exhibits an average 7% increase compared to each one of the previous decades. A similar behavior was found for the decadal average of the heights of maximum annual positive storm surges. In this case the average height of the last two decades exceeds that of the previous decades by approximately 8 cm. The decadal average of maximum annual duration of these meteorological events shows an increase of 2 h in the last three decades. A possible explanation of the changes in frequency, height and duration of positive storm surges at Mar del Plata would seem to lie in the relative mean sea-level rise.

Large surface-enhanced Raman scattering from self-assembled gold nanosphere monolayers

NASA Astrophysics Data System (ADS)

Fontana, Jake; Livenere, John; Bezares, Francisco J.; Caldwell, Joshua D.; Rendell, Ronald; Ratna, Banahalli R.

2013-05-01

We demonstrate an average surface-enhanced Raman scattering enhancement on the order of 108 from benzenethiol molecules using self-assembled, macroscopic, and tunable gold nanosphere monolayers on non-templated substrates. The self-assembly of the nanosphere monolayers uses a simple and efficient technique that allows for the creation of a high-density, chemically functionalized gold nanosphere monolayers with enhancement factors comparable to those produced using top-down fabrication techniques. These films may provide an approach for the future development of portable chemical/biological sensors.

The Orbiting Carbon Observatory Mission: Watching the Earth Breathe Mapping CO2 from Space

NASA Technical Reports Server (NTRS)

Boain, Ron

2007-01-01

Approach: Collect spatially resolved, high resolution spectroscopic observations of CO2 and O2 absorption in reflected sunlight. Use these data to resolve spatial and temporal variations in the column averaged CO2 dry air mole fraction, X(sub CO2) over the sunlit hemisphere. Employ independent calibration and validation approaches to produce X(sub CO2) estimates with random errors and biases no larger than 1-2 ppm (0.3-0.5%) on regional scales at monthly intervals.

Actively mode-locked diode laser with a mode spacing stability of ∼6 × 10{sup -14}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zakharyash, V F; Kashirsky, A V; Klementyev, V M

We have studied mode spacing stability in an actively mode-locked external-cavity semiconductor laser. It has been shown that, in the case of mode spacing pulling to the frequency of a highly stable external microwave signal produced by a hydrogen standard (stability of 4 × 10{sup -14} over an averaging period τ = 10 s), this configuration ensures a mode spacing stability of 5.92 × 10{sup -14} (τ = 10 s). (control of radiation parameters)

Ultraviolet light-induced mutants of Streptococcus lactis subspecies diacetylactis with enhanced acid- or flavor-producing abilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuila, R.K.; Ranganathan, B.

1978-04-01

A strain of Streptococcus lactis subspecies diacetylactis S/sub 1/ isolated from fresh milk was exposed to 7200 ergs/mm/sup 2/ of ultraviolet radiation. Over 8100 colonies surviving from 7.4 x 10/sup 6/ cells exposed to radiation were screened on citrate agar for detection and isolation of mutants with increased flavor and/or acid production. Of the survivors, 960 were type-I mutants that exhibited clear zone on citrate agar after 18 h (presumed to be high diacetyl producers), and 288 were type-II mutants which did not exhibit clear zones on citrate agar for up to 72 h (high acid producers). Type-II mutants producedmore » an average .93 percent titratable acidity which was 34 percent more than the .69 percent of the parent. Reduction in titratable acidity (56 percent less) was considerable in type-I mutants, compared with the parent culture. Diacetyl + acetoin production by type-I mutants was 137.9 ppM which has 4.5 times more than that of the parental strain. Acetaldehyde production in the mutants varied from 1.5 to 34.5 ppM (parent culture 3.0 ppM). The mutants with increased acid and high acetoin plus diacetyl production were stable after 50 subcultures in milk.« less

Characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil.

PubMed

Song, Geum-Ju; Seo, Yong-Chil; Pudasainee, Deepak; Kim, In-Tae

2010-07-01

An attempt has been made to recover high-calorific fuel gas and useful carbonaceous residue by the electric arc pyrolysis of waste lubricating oil. The characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil were investigated in this study. The produced gas was mainly composed of hydrogen (35-40%), acetylene (13-20%), ethylene (3-4%) and other hydrocarbons, whereas the concentration of CO was very low. Calorific values of gas ranged from 11,000 to 13,000 kcal kg(-1) and the concentrations of toxic gases, such as NO(x), HCl and HF, were below the regulatory emissions limit. Gas chromatography-mass spectrometry (GC/MS) analysis of liquid-phase residues showed that high molecular-weight hydrocarbons in waste lubricating oil were pyrolyzed into low molecular-weight hydrocarbons and hydrogen. Dehydrogenation was found to be the main pyrolysis mechanism due to the high reaction temperature induced by electric arc. The average particle size of soot as carbonaceous residue was about 10 microm. The carbon content and heavy metals in soot were above 60% and below 0.01 ppm, respectively. The utilization of soot as industrial material resources such as carbon black seems to be feasible after refining and grinding. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

Inorganic dual-layer microporous supported membranes

DOEpatents

Brinker, C. Jeffrey; Tsai, Chung-Yi; Lu, Yungfeng

2003-03-25

The present invention provides for a dual-layer inorganic microporous membrane capable of molecular sieving, and methods for production of the membranes. The inorganic microporous supported membrane includes a porous substrate which supports a first inorganic porous membrane having an average pore size of less than about 25 .ANG. and a second inorganic porous membrane coating the first inorganic membrane having an average pore size of less than about 6 .ANG.. The dual-layered membrane is produced by contacting the porous substrate with a surfactant-template polymeric sol, resulting in a surfactant sol coated membrane support. The surfactant sol coated membrane support is dried, producing a surfactant-templated polymer-coated substrate which is calcined to produce an intermediate layer surfactant-templated membrane. The intermediate layer surfactant-templated membrane is then contacted with a second polymeric sol producing a polymeric sol coated substrate which is dried producing an inorganic polymeric coated substrate. The inorganic polymeric coated substrate is then calcined producing an inorganic dual-layered microporous supported membrane in accordance with the present invention.

Aspergillus parasiticus communities associated with sugarcane in the Rio Grande Valley of Texas: implications of global transport and host association within Aspergillus section Flavi.

PubMed

Garber, N P; Cotty, P J

2014-05-01

In the Rio Grande Valley of Texas (RGV), values of maize and cottonseed crops are significantly reduced by aflatoxin contamination. Aflatoxin contamination of susceptible crops is the product of communities of aflatoxin producers and the average aflatoxin-producing potentials of these communities influence aflatoxin contamination risk. Cropping pattern influences community composition and, thereby, the epidemiology of aflatoxin contamination. In 2004, Aspergillus parasiticus was isolated from two fields previously cropped to sugarcane but not from 23 fields without recent history of sugarcane cultivation. In 2004 and 2005, A. parasiticus composed 18 to 36% of Aspergillus section Flavi resident in agricultural soils within sugarcane-producing counties. A. parasiticus was not detected in counties that do not produce sugarcane. Aspergillus section Flavi soil communities within sugarcane-producing counties differed significantly dependent on sugarcane cropping history. Fields cropped to sugarcane within the previous 5 years had greater quantities of A. parasiticus (mean = 16 CFU/g) than fields not cropped to sugarcane (mean = 0.1 CFU/g). The percentage of Aspergillus section Flavi composed of A. parasiticus increased to 65% under continuous sugarcane cultivation and remained high the first season of rotation out of sugarcane. Section Flavi communities in fields rotated to non-sugarcane crops for 3 to 5 years were composed of <5% A. parasiticus, and fields with no sugarcane history averaged only 0.2% A. parasiticus. The section Flavi community infecting RGV sugarcane stems ranged from 95% A. parasiticus in billets prepared for commercial planting to 52% A. parasiticus in hand-collected sugarcane stems. Vegetative compatibility assays and multilocus phylogenies verified that aflatoxin contamination of raw sugar was previously attributed to similar A. parasiticus in Japan. Association of closely related A. parasiticus genotypes with sugarcane produced in Japan and RGV, frequent infection of billets by these genotypes, and the ephemeral nature of A. parasiticus in RGV soils suggests global transport with sugarcane planting material.

Evaluation and modification of five techniques for estimating stormwater runoff for watersheds in west-central Florida

USGS Publications Warehouse

Trommer, J.T.; Loper, J.E.; Hammett, K.M.

1996-01-01

Several traditional techniques have been used for estimating stormwater runoff from ungaged watersheds. Applying these techniques to water- sheds in west-central Florida requires that some of the empirical relationships be extrapolated beyond tested ranges. As a result, there is uncertainty as to the accuracy of these estimates. Sixty-six storms occurring in 15 west-central Florida watersheds were initially modeled using the Rational Method, the U.S. Geological Survey Regional Regression Equations, the Natural Resources Conservation Service TR-20 model, the U.S. Army Corps of Engineers Hydrologic Engineering Center-1 model, and the Environmental Protection Agency Storm Water Management Model. The techniques were applied according to the guidelines specified in the user manuals or standard engineering textbooks as though no field data were available and the selection of input parameters was not influenced by observed data. Computed estimates were compared with observed runoff to evaluate the accuracy of the techniques. One watershed was eliminated from further evaluation when it was determined that the area contributing runoff to the stream varies with the amount and intensity of rainfall. Therefore, further evaluation and modification of the input parameters were made for only 62 storms in 14 watersheds. Runoff ranged from 1.4 to 99.3 percent percent of rainfall. The average runoff for all watersheds included in this study was about 36 percent of rainfall. The average runoff for the urban, natural, and mixed land-use watersheds was about 41, 27, and 29 percent, respectively. Initial estimates of peak discharge using the rational method produced average watershed errors that ranged from an underestimation of 50.4 percent to an overestimation of 767 percent. The coefficient of runoff ranged from 0.20 to 0.60. Calibration of the technique produced average errors that ranged from an underestimation of 3.3 percent to an overestimation of 1.5 percent. The average calibrated coefficient of runoff for each watershed ranged from 0.02 to 0.72. The average values of the coefficient of runoff necessary to calibrate the urban, natural, and mixed land-use watersheds were 0.39, 0.16, and 0.08, respectively. The U.S. Geological Survey regional regression equations for determining peak discharge produced errors that ranged from an underestimation of 87.3 percent to an over- estimation of 1,140 percent. The regression equations for determining runoff volume produced errors that ranged from an underestimation of 95.6 percent to an overestimation of 324 percent. Regression equations developed from data used for this study produced errors that ranged between an underestimation of 82.8 percent and an over- estimation of 328 percent for peak discharge, and from an underestimation of 71.2 percent to an overestimation of 241 percent for runoff volume. Use of the equations developed for west-central Florida streams produced average errors for each type of watershed that were lower than errors associated with use of the U.S. Geological Survey equations. Initial estimates of peak discharges and runoff volumes using the Natural Resources Conservation Service TR-20 model, produced average errors of 44.6 and 42.7 percent respectively, for all the watersheds. Curve numbers and times of concentration were adjusted to match estimated and observed peak discharges and runoff volumes. The average change in the curve number for all the watersheds was a decrease of 2.8 percent. The average change in the time of concentration was an increase of 59.2 percent. The shape of the input dimensionless unit hydrograph also had to be adjusted to match the shape and peak time of the estimated and observed flood hydrographs. Peak rate factors for the modified input dimensionless unit hydrographs ranged from 162 to 454. The mean errors for peak discharges and runoff volumes were reduced to 18.9 and 19.5 percent, respectively, using the average calibrated input parameters for ea

Fractured-aquifer hydrogeology from geophysical logs; the passaic formation, New Jersey

USGS Publications Warehouse

Morin, R.H.; Carleton, G.B.; Poirier, S.

1997-01-01

The Passaic Formation consists of gradational sequences of mudstone, siltstone, and sandstone, and is a principal aquifer in central New Jersey. Ground-water flow is primarily controlled by fractures interspersed throughout these sedimentary rocks and characterizing these fractures in terms of type, orientation, spatial distribution, frequency, and transmissivity is fundamental towards understanding local fluid-transport processes. To obtain this information, a comprehensive suite of geophysical logs was collected in 10 wells roughly 46 m in depth and located within a .05 km2 area in Hopewell Township, New Jersey. A seemingly complex, heterogeneous network of fractures identified with an acoustic televiewer was statistically reduced to two principal subsets corresponding to two distinct fracture types: (1) bedding-plane partings and (2) high-angle fractures. Bedding-plane partings are the most numerous and have an average strike of N84??W and dip of 20??N. The high-angle fractures are oriented subparallel to these features, with an average strike of N79??E and dip of 71??S, making the two fracture types roughly orthogonal. Their intersections form linear features that also retain this approximately east-west strike. Inspection of fluid temperature and conductance logs in conjunction with flowmeter measurements obtained during pumping allows the transmissive fractures to be distinguished from the general fracture population. These results show that, within the resolution capabilities of the logging tools, approximately 51 (or 18 percent) of the 280 total fractures are water producing. The bedding-plane partings exhibit transmissivities that average roughly 5 m2/day and that generally diminish in magnitude and frequency with depth. The high-angle fractures have average transmissivities that are about half those of the bedding-plane partings and show no apparent dependence upon depth. The geophysical logging results allow us to infer a distinct hydrogeologic structure within this aquifer that is defined by fracture type and orientation. Fluid flow near the surface is controlled primarily by the highly transmissive, subhorizontal bedding-plane partings. As depth increases, the high-angle fractures apparently become more dominant hydrologically.The Passaic Formation consists of gradational sequences of mudstone, siltstone, and sandstone, and is a principal aquifer in central New Jersey. Ground-water flow is primarily controlled by fractures interspersed throughout these sedimentary rocks and characterizing these fractures in terms of type, orientation, spatial distribution, frequency, and transmissivity is fundamental towards understanding local fluid-transport processes. To obtain this information, a comprehensive suite of geophysical logs was collected in 10 wells roughly 46 m in depth and located within a .05 km2 area in Hopewell Township, New Jersey. A seemingly complex, heterogeneous network of fractures identified with an acoustic televiewer was statistically reduced to two principal subsets corresponding to two distinct fracture types: (1) bedding-plane partings and (2) high-angle fractures. Bedding-plane partings are the most numerous and have an average strike of N84?? W and dip of 20?? N. The high-angle fractures are oriented subparallel to these features, with an average strike of N79?? E and dip of 71?? S, making the two fracture types roughly orthogonal. Their intersections form linear features that also retain this approximately east-west strike. Inspection of fluid temperature and conductance logs in conjunction with flowmeter measurements obtained during pumping allows the transmissive fractures to be distinguished from the general fracture population. These results show that, within the resolution capabilities of the logging tools, approximately 51 (or 18 percent) of the 280 total fractures are water producing. The bedding-plane partings exhibit transmissivities that average roughly 5 m2/day and that generally dimi

Influence of calcium and phosphorus, lactose, and salt-to-moisture ratio on Cheddar cheese quality: manufacture and composition.

PubMed

Upreti, P; Metzger, L E

2006-02-01

Eight Cheddar cheeses with 2 levels of calcium (Ca) and phosphorus (P), residual lactose, and salt-to-moisture ratio (S/M) were manufactured. All cheeses were made using a stirred-curd procedure and were replicated 3 times. Treatments with a high level of Ca and P were produced by setting the milk and drawing the whey at a higher pH (6.6 and 6.3, respectively) compared with the treatments with a low level of Ca and P (pH of 6.2 and 5.7, respectively). The lactose content in the cheeses was varied by adding lactose (2.5% by weight of milk) to the milk for high lactose cheeses, and washing the curd for low lactose cheeses. The difference in S/M was obtained by dividing the curds into halves, weighing each half, and salting at 3.5 and 2.25% of the weight of the curd for high and low S/M, respectively. All cheeses were salted at a pH of 5.4. Modifications in cheese-making protocols produced cheeses with desired differences in Ca and P, residual lactose, and S/M. Average Ca and P in the high Ca and P cheeses was 0.68 and 0.48%, respectively, vs. 0.53 and 0.41% for the low Ca and P cheeses. Average lactose content of the high lactose treatments at d 1 was 1.48% compared with 0.30% for the low lactose treatments. The S/M for the high and low S/M cheeses was 6.68 and 4.77%, respectively. Mean moisture, fat, and protein content of the cheeses ranged from 32.07 to 37.57%, 33.32 to 35.93%, and 24.46 to 26.40%, respectively. The moisture content differed among the treatments, whereas fat and protein content on dry basis was similar.

40 CFR 421.266 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average mg/troy ounce of... day Maximum for monthly average mg/troy ounce of precious metals, in the granulated raw material... average mg/troy ounce of gold produced by cyanide stripping Copper 4.736 2.257 Cyanide (total) 0.740 0.296...

Investigating speech perception in children with dyslexia: is there evidence of a consistent deficit in individuals?

PubMed Central

Messaoud-Galusi, Souhila; Hazan, Valerie; Rosen, Stuart

2012-01-01

Purpose The claim that speech perception abilities are impaired in dyslexia was investigated in a group of 62 dyslexic children and 51 average readers matched in age. Method To test whether there was robust evidence of speech perception deficits in children with dyslexia, speech perception in noise and quiet was measured using eight different tasks involving the identification and discrimination of a complex and highly natural synthetic ‘pea’-‘bee’ contrast (copy synthesised from natural models) and the perception of naturally-produced words. Results Children with dyslexia, on average, performed more poorly than average readers in the synthetic syllables identification task in quiet and in across-category discrimination (but not when tested using an adaptive procedure). They did not differ from average readers on two tasks of word recognition in noise or identification of synthetic syllables in noise. For all tasks, a majority of individual children with dyslexia performed within norms. Finally, speech perception generally did not correlate with pseudo-word reading or phonological processing, the core skills related to dyslexia. Conclusions On the tasks and speech stimuli we used, most children with dyslexia do not appear to show a consistent deficit in speech perception. PMID:21930615

Changes to Extender, Cryoprotective Medium, and In Vitro Fertilization Improve Zebrafish Sperm Cryopreservation.

PubMed

Matthews, Jennifer L; Murphy, Joy M; Carmichael, Carrie; Yang, Huiping; Tiersch, Terrence; Westerfield, Monte; Varga, Zoltan M

2018-01-25

Sperm cryopreservation is a highly efficient method for preserving genetic resources. It extends the reproductive period of males and significantly reduces costs normally associated with maintenance of live animal colonies. However, previous zebrafish (Danio rerio) cryopreservation methods have produced variable outcomes and low post-thaw fertilization rates. To improve post-thaw fertilization rates after cryopreservation, we developed a new extender and cryoprotective medium (CPM), introduced quality assessment (QA), determined the optimal cooling rate, and improved the post-thaw in vitro fertilization process. We found that the hypertonic extender E400 preserved motility of sperm held on ice for at least 6 h. We implemented QA by measuring sperm cell densities with a NanoDrop spectrophotometer and sperm motility with computer-assisted sperm analysis (CASA). We developed a CPM, RMMB, which contains raffinose, skim milk, methanol, and bicine buffer. Post-thaw motility indicated that the optimal cooling rate in two types of cryogenic vials was between 10 and 15°C/min. Test thaws from this method produced average motility of 20% ± 13% and an average post-thaw fertilization rate of 68% ± 16%.

Quantification of soil and water losses in an extensive olive orchard catchment in Southern Spain

NASA Astrophysics Data System (ADS)

Rodrigo-Comino, Jesús; Taguas, Encarnación; Seeger, Manuel; Ries, Johannes B.

2018-01-01

A sound understanding of erosive processes at different scales can contribute substantially to the design of suitable management strategies. The main aim of this work was to evaluate key factors at the pedon scale that cause soil erosion to occur. To achieve this goal, we quantified infiltration, permeability, soil losses and runoff volumes in a small Southern Spanish catchment cultivated with olive orchards. To assess which factor contributed most to speeding up soil erosion, a Spearman rank coefficient and principal components analysis were carried out. The results confirmed low infiltration values (11.8 mm h-1) in the surface soil layers and high permeability values (24.6 mm h-1) in the sub-surface soil layers, and produced an average soil loss of 19.7 g m-2 and average runoff coefficients of 26.1%. Statistical analyses showed that: i) the generation of runoff was closely correlated with soil loss; and, ii) an increase in the vegetation cover helped reduce soil erosion. In comparison to larger areas such as a catchment, the pedon scale produced lower or similar soil losses and runoff coefficients in rainfall simulation conditions, although the influence of vegetation cover as a control factor was also detected.

Synthesis of ultrasmall, homogeneously alloyed, bimetallic nanoparticles on silica supports

NASA Astrophysics Data System (ADS)

Wong, A.; Liu, Q.; Griffin, S.; Nicholls, A.; Regalbuto, J. R.

2017-12-01

Supported nanoparticles containing more than one metal have a variety of applications in sensing, catalysis, and biomedicine. Common synthesis techniques for this type of material often result in large, unalloyed nanoparticles that lack the interactions between the two metals that give the particles their desired characteristics. We demonstrate a relatively simple, effective, generalizable method to produce highly dispersed, well-alloyed bimetallic nanoparticles. Ten permutations of noble and base metals (platinum, palladium, copper, nickel, and cobalt) were synthesized with average particle sizes from 0.9 to 1.4 nanometers, with tight size distributions. High-resolution imaging and x-ray analysis confirmed the homogeneity of alloying in these ultrasmall nanoparticles.

Probing the atomic structure of metallic nanoclusters with the tip of a scanning tunneling microscope.

PubMed

Schouteden, Koen; Lauwaet, Koen; Janssens, Ewald; Barcaro, Giovanni; Fortunelli, Alessandro; Van Haesendonck, Chris; Lievens, Peter

2014-02-21

Preformed Co clusters with an average diameter of 2.5 nm are produced in the gas phase and are deposited under controlled ultra-high vacuum conditions onto a thin insulating NaCl film on Au(111). Relying on a combined experimental and theoretical investigation, we demonstrate visualization of the three-dimensional atomic structure of the Co clusters by high-resolution scanning tunneling microscopy (STM) using a Cl functionalized STM tip that can be obtained on the NaCl surface. More generally, use of a functionalized STM tip may allow for systematic atomic structure determination with STM of nanoparticles that are deposited on metal surfaces.

Development of deep-ultraviolet metal vapor lasers

NASA Astrophysics Data System (ADS)

Sabotinov, Nikola V.

2004-06-01

Deep ultraviolet laser generation is of great interest in connection with both the development of new industrial technologies and applications in medicine, biology, chemistry, etc. The development of metal vapor UV lasers oscillating in the pulsed mode with high pulse repetition frequencies and producing high average output powers is of particular interest for microprocessing of polymers, photolithography and fluorescence applications. At present, metal vapor lasers generate deep-UV radiation on the base of two methods. The first method is non-linear conversion of powerful laser generation from the visible region into the deep ultraviolet region. The second method is direct UV laser action on ion and atomic transitions of different metals.

Laser ablative synthesis of carbon nanotubes

DOEpatents

Smith, Michael W.; Jordan, Kevin; Park, Cheol

2010-03-02

An improved method for the production of single walled carbon nanotubes that utilizes an RF-induction heated side-pumped synthesis chamber for the production of such. Such a method, while capable of producing large volumes of carbon nanotubes, concurrently permits the use of a simplified apparatus that allows for greatly reduced heat up and cool down times and flexible flowpaths that can be readily modified for production efficiency optimization. The method of the present invention utilizes a free electron laser operating at high average and peak fluence to illuminate a rotating and translating graphite/catalyst target to obtain high yields of SWNTs without the use of a vacuum chamber.

Enhancement of biogas production by co-digestion of potato pulp with cow manure in a CSTR system.

PubMed

Sanaei-Moghadam, Akbar; Abbaspour-Fard, Mohammad Hossein; Aghel, Hasan; Aghkhani, Mohammad Hossein; Abedini-Torghabeh, Javad

2014-08-01

Anaerobic digestion (AD) process is a well-established method to generate energy from the organic wastes both from the environmental and economical perspectives. The purpose of present study is to evaluate energy production from potato wastes by incorporating cow manure into the process. Firstly, a laboratory pilot of one-stage biogas production was designed and built according to continuously stirred tank reactor (CSTR) system. The setup was able to automatically control the environmental conditions of the process including temperature, duration, and rate of stirring. AD experiment was exclusively performed on co-digestion of potato peel (PP) and cow manure (CM) in three levels of mixing ratio including 20:80, 50:50, 80:20 (PP:CM), and 0:100 as control treatment based on the volatile solid (VS) weight without adding initial inoculums. After hydraulic retention time (HRT) of 50 days on average 193, 256, 348, and 149 norm liter (LN) (kg VS)(-1), methane was produced for different mixing ratios, respectively. Statistical analysis shows that these gas productions are significantly different. The average energy was determined based on the produced methane which was about 2.8 kWh (kg VS)(-1), implying a significant energy production potential. The average chemical oxygen demand (COD) removal of treatments was about 61%, showing that it can be leached significantly with high organic matter by the employed pilot. The energy efficiency of 92% of the process also showed the optimum control of the process by the pilot.

Precipitation interpolation in mountainous areas

NASA Astrophysics Data System (ADS)

Kolberg, Sjur

2015-04-01

Different precipitation interpolation techniques as well as external drift covariates are tested and compared in a 26000 km2 mountainous area in Norway, using daily data from 60 stations. The main method of assessment is cross-validation. Annual precipitation in the area varies from below 500 mm to more than 2000 mm. The data were corrected for wind-driven undercatch according to operational standards. While temporal evaluation produce seemingly acceptable at-station correlation values (on average around 0.6), the average daily spatial correlation is less than 0.1. Penalising also bias, Nash-Sutcliffe R2 values are negative for spatial correspondence, and around 0.15 for temporal. Despite largely violated assumptions, plain Kriging produces better results than simple inverse distance weighting. More surprisingly, the presumably 'worst-case' benchmark of no interpolation at all, simply averaging all 60 stations for each day, actually outperformed the standard interpolation techniques. For logistic reasons, high altitudes are under-represented in the gauge network. The possible effect of this was investigated by a) fitting a precipitation lapse rate as an external drift, and b) applying a linear model of orographic enhancement (Smith and Barstad, 2004). These techniques improved the results only marginally. The gauge density in the region is one for each 433 km2; higher than the overall density of the Norwegian national network. Admittedly the cross-validation technique reduces the gauge density, still the results suggest that we are far from able to provide hydrological models with adequate data for the main driving force.

An investigation into the vector ellipticity of extremely low frequency magnetic fields from appliances in UK homes

NASA Astrophysics Data System (ADS)

Ainsbury, Elizabeth A.; Conein, Emma; Henshaw, Denis L.

2005-07-01

Elliptically polarized magnetic fields induce higher currents in the body compared with their plane polarized counterparts. This investigation examines the degree of vector ellipticity of extremely low frequency magnetic fields (ELF-MFs) in the home, with regard to the adverse health effects reportedly associated with ELF-MFs, for instance childhood leukaemia. Tri-axial measurements of the magnitude and phase of the 0-3000 Hz magnetic fields, produced by 226 domestic mains-fed appliances of 32 different types, were carried out in 16 homes in Worcestershire in the summer of 2004. Magnetic field strengths were low, with average (RMS) values of 0.03 ± 0.02 µT across all residences. In contrast, background field ellipticities were high, on average 47 ± 11%. Microwave and electric ovens produced the highest ellipticities: mean respective values of 21 ± 21% and 21 ± 17% were observed 20 cm away from these appliances. There was a negative correlation between field strength and field polarization, which we attribute to the higher relative field contribution close to each individual (single-phase) appliance. The measurements demonstrate that domestic magnetic fields are extremely complex and cannot simply be characterized by traditional measurements such as time-weighted average or peak exposure levels. We conclude that ellipticity should become a relevant metric for future epidemiological studies of health and ELF-MF exposure. This work is supported by the charity CHILDREN with LEUKAEMIA, registered charity number 298405.

Which Subsystems used to produce archival science products?

Atmospheric Science Data Center

2014-12-08

... - Combine telemetry and ephemeris data to produce Earth location geometry and convert radiometric counts produced by the ... inversion techniques. Daily and Monthly Time/Space Averaging - Convert from time-ordered to regionally-accessible data ... Data Products - Generate well-documented science archival products in an easily accessible format. ...

7 CFR 1126.62 - Announcement of producer prices.

Code of Federal Regulations, 2014 CFR

2014-01-01

... following prices and information: (a) The producer price differential; (b) The protein price; (c) The nonfat...; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by combining the...

7 CFR 1032.62 - Announcement of producer prices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1126.62 - Announcement of producer prices.

Code of Federal Regulations, 2013 CFR

2013-01-01

... following prices and information: (a) The producer price differential; (b) The protein price; (c) The nonfat...; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by combining the...

7 CFR 1030.62 - Announcement of producer prices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, nonfat solids, protein and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1033.62 - Announcement of producer prices.

Code of Federal Regulations, 2012 CFR

2012-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1032.62 - Announcement of producer prices.

Code of Federal Regulations, 2014 CFR

2014-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1033.62 - Announcement of producer prices.

Code of Federal Regulations, 2014 CFR

2014-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1126.62 - Announcement of producer prices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... following prices and information: (a) The producer price differential; (b) The protein price; (c) The nonfat...; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by combining the...

7 CFR 1032.62 - Announcement of producer prices.

Code of Federal Regulations, 2011 CFR

2011-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1126.62 - Announcement of producer prices.

Code of Federal Regulations, 2011 CFR

2011-01-01

... following prices and information: (a) The producer price differential; (b) The protein price; (c) The nonfat...; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by combining the...

7 CFR 1030.62 - Announcement of producer prices.

Code of Federal Regulations, 2012 CFR

2012-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, nonfat solids, protein and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1033.62 - Announcement of producer prices.

Code of Federal Regulations, 2011 CFR

2011-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1033.62 - Announcement of producer prices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1126.62 - Announcement of producer prices.

Code of Federal Regulations, 2012 CFR

2012-01-01

... following prices and information: (a) The producer price differential; (b) The protein price; (c) The nonfat...; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by combining the...

7 CFR 1032.62 - Announcement of producer prices.

Code of Federal Regulations, 2012 CFR

2012-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1032.62 - Announcement of producer prices.

Code of Federal Regulations, 2013 CFR

2013-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1030.62 - Announcement of producer prices.

Code of Federal Regulations, 2011 CFR

2011-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, nonfat solids, protein and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1030.62 - Announcement of producer prices.

Code of Federal Regulations, 2013 CFR

2013-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, nonfat solids, protein and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1030.62 - Announcement of producer prices.

Code of Federal Regulations, 2014 CFR

2014-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, nonfat solids, protein and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

7 CFR 1033.62 - Announcement of producer prices.

Code of Federal Regulations, 2013 CFR

2013-01-01

... publicly the following prices and information: (a) The producer price differential; (b) The protein price... cell adjustment rate; (g) The average butterfat, protein, nonfat solids, and other solids content of producer milk; and (h) The statistical uniform price for milk containing 3.5 percent butterfat, computed by...

24 CFR Appendix I to Subpart B of... - Definition of Acoustical Quantities

Code of Federal Regulations, 2010 CFR

2010-04-01

... micropascals. Day-night average sound level, abbreviated as DNL, and symbolized mathematically as Ldn is... day-night average sound level produced by the loud impulsive sounds shall have 8 decibels added to it...

Abrupt shift in δ18O values at Medicine Lake volcano (California, USA)

USGS Publications Warehouse

Donnelly-Nolan, J. M.

1998-01-01

 Oxygen-isotope analyses of lavas from Medicine Lake volcano (MLV), in the southern Cascade Range, indicate a significant change in δ18O in Holocene time. In the Pleistocene, basaltic lavas with <52% SiO2 averaged +5.9‰, intermediate lavas averaged +5.7‰, and silicic lavas (≥63.0%SiO2) averaged +5.6‰. No analyzed Pleistocene rhyolites or dacites have values greater than +6.3‰. In post-glacial time, basalts were similar at +5.7‰ to those erupted in the Pleistocene, but intermediate lavas average +6.8‰ and silicic lavas +7.4‰ with some values as high as +8.5‰. The results indicate a change in the magmatic system supplying the volcano. During the Pleistocene, silicic lavas resulted either from melting of low-18O crust or from fractionation combined with assimilation of very-low-18O crustal material such as hydrothermally altered rocks similar to those found in drill holes under the center of the volcano. By contrast, Holocene silicic lavas were produced by assimilation and/or wholesale melting of high-18O crustal material such as that represented by inclusions of granite in lavas on the upper flanks of MLV. This sudden shift in assimilant indicates a fundamental change in the magmatic system. Magmas are apparently ponding in the crust at a very different level than in Pleistocene time.

Simulation of the effects of seasonally varying pumping on intraborehole flow and the vulnerability of public-supply wells to contamination

USGS Publications Warehouse

Yager, Richard M.; Heywood, Charles E.

2014-01-01

Public-supply wells with long screens in alluvial aquifers can produce waters of differing quality from different depths. Seasonal changes in quality are linked to seasonal changes in pumping rates that influence the distribution of flow into the well screens under pumping conditions and the magnitude and direction of intraborehole flow within the wells under ambient conditions. Groundwater flow and transport simulations with MODFLOW and MT3DMS were developed to quantify the effects of changes in average seasonal pumping rates on intraborehole flow and water quality at two long-screened, public-supply wells, in Albuquerque, New Mexico and Modesto, California, where widespread pumping has altered groundwater flow patterns. Simulation results indicate that both wells produce water requiring additional treatment to maintain potable quality in winter when groundwater withdrawals are reduced because less water is derived from parts of the aquifer that contain water requiring less treatment. Simulation results indicate that the water quality at both wells could be improved by increasing average winter-pumping rates to induce more lateral flow from parts of the aquifer that contain better quality water. Arsenic-bearing water produced by the Albuquerque well could be reduced from 55% to 45% by doubling average winter-pumping rate, while nitrate- and uranium-bearing water produced by the Modesto well could be reduced from 95% to 65% by nearly tripling the average winter-pumping rate. Higher average winter-pumping rates would also reduce the volume of intraborehole flow within both wells and prevent the exchange of poor quality water between shallow and deep parts of both aquifers.

Efficient Array Design for Sonotherapy

PubMed Central

Stephens, Douglas N.; Kruse, Dustin E.; Ergun, Arif S.; Barnes, Stephen; Ming Lu, X.; Ferrara, Katherine

2008-01-01

New linear multi-row, multi-frequency arrays have been designed, constructed and tested as fully operational ultrasound probes to produce confocal imaging and therapeutic acoustic intensities with a standard commercial ultrasound imaging system. The triple-array probes and imaging system produce high quality B-mode images with a center row imaging array at 5.3 MHz, and sufficient acoustic power with dual therapeutic arrays to produce mild hyperthermia at 1.54 MHz. The therapeutic array pair in the first probe design (termed G3) utilizes a high bandwidth and peak pressure, suitable for mechanical therapies. The second multi-array design (termed G4) has a redesigned therapeutic array pair which is optimized for high time-averaged power output suitable for mild hyperthermia applications. The “thermal therapy” design produces more than 4 Watts of acoustic power from the low frequency arrays with only a 10.5 °C internal rise in temperature after 100 seconds of continuous use with an unmodified conventional imaging system, or substantially longer operation at lower acoustic power. The low frequency arrays in both probe designs were examined and contrasted for real power transfer efficiency with a KLM model which includes all lossy contributions in the power delivery path from system transmitters to tissue load. Laboratory verification was successfully performed for the KLM derived estimates of transducer parallel model acoustic resistance and dissipation resistance, which are the critical design factors for acoustic power output and undesired internal heating respectively. PMID:18591737

Preliminary investigation of electrothermal vaporization sample introduction for inductively coupled plasma time-of-flight mass spectrometry.

PubMed

Mahoney, P P; Ray, S J; Li, G; Hieftje, G M

1999-04-01

The coupling of an electrothermal vaporization (ETV) apparatus to an inductively coupled plasma time-of-flight mass spectrometer (ICP-TOFMS) is described. The ability of the ICP-TOFMS to produce complete elemental mass spectra at high repetition rates is experimentally demonstrated. A signal-averaging data acquisition board is employed to rapidly record complete elemental spectra throughout the vaporization stage of the ETV temperature cycle; a solution containing 34 elements is analyzed. The reduction of both molecular and atomic isobaric interferences through the temperature program of the furnace is demonstrated. Isobaric overlaps among the isotopes of cadmium, tin, and indium are resolved by exploiting differences in the vaporization characteristics of the elements. Figures of merit for the system are defined with several different data acquisition schemes capable of operating at the high repetition rate of the TOF instrument. With the use of both ion counting and a boxcar averager, the dynamic range is shown to be linear over a range of at least 6 orders of magnitude. A pair of boxcar averagers are used to measure the isotope ratio for silver with a precision of 1.9% RSD, despite a cycle-to-cycle precision of 19% RSD. Detection limits of 10-80 fg are calculated for seven elements, based upon a 10-microL injection.

High-Throughput RNA Interference Screening: Tricks of the Trade

PubMed Central

Nebane, N. Miranda; Coric, Tatjana; Whig, Kanupriya; McKellip, Sara; Woods, LaKeisha; Sosa, Melinda; Sheppard, Russell; Rasmussen, Lynn; Bjornsti, Mary-Ann; White, E. Lucile

2016-01-01

The process of validating an assay for high-throughput screening (HTS) involves identifying sources of variability and developing procedures that minimize the variability at each step in the protocol. The goal is to produce a robust and reproducible assay with good metrics. In all good cell-based assays, this means coefficient of variation (CV) values of less than 10% and a signal window of fivefold or greater. HTS assays are usually evaluated using Z′ factor, which incorporates both standard deviation and signal window. A Z′ factor value of 0.5 or higher is acceptable for HTS. We used a standard HTS validation procedure in developing small interfering RNA (siRNA) screening technology at the HTS center at Southern Research. Initially, our assay performance was similar to published screens, with CV values greater than 10% and Z′ factor values of 0.51 ± 0.16 (average ± standard deviation). After optimizing the siRNA assay, we got CV values averaging 7.2% and a robust Z′ factor value of 0.78 ± 0.06 (average ± standard deviation). We present an overview of the problems encountered in developing this whole-genome siRNA screening program at Southern Research and how equipment optimization led to improved data quality. PMID:23616418

Chemical and mineralogical changes of waste and tailings from the Murgul Cu deposit (Artvin, NE Turkey): implications for occurrence of acid mine drainage.

PubMed

Sağlam, Emine Selva; Akçay, Miğraç

2016-04-01

Being one of the largest copper-producing resources in Turkey, the Murgul deposit has been a source of environmental pollution for very long time. Operated through four open pits with an annual production of about 3 million tons of ore at an average grade of about 0.5% Cu, the deposit to date has produced an enormous pile of waste (exceeding 100 million tons) with tailings composed of 36 % SiO2, 39% Fe2O3 and 32% S, mainly in the form of pyrite and quartz. Waters in the vicinity of the deposit vary from high acid-acid (2.71-3.85) and high-extremely metal rich (34.48-348.12 mg/l in total) in the open pits to near neutral (6.51-7.83) and low metal (14.39-973.52 μg/l in total) in downstream environments. Despite low metal contents and near neutral pH levels of the latter, their suspended particle loads are extremely high and composed mainly of quartz and clay minerals with highly elevated levels of Fe (3.5 to 24.5% Fe2O3; 11% on average) and S (0.5 to 20.6% S; 7% on average), showing that Fe is mainly in the form of pyrite and lesser hematite. They also contain high concentrations of As, Au, Ba, Cu, Pb, and Zn. Waters collected along the course of polluted drainages are supersaturated with respect to Fe phases such as goethite, hematite, maghemite, magnetite, schwertmannite and ferrihydrite. Secondary phases such as Fe-sulphates are only found near the pits, but not along the streams due to neutral pH conditions, where pebbles are covered and cemented by Fe-oxides and hydroxides indicating that oxidation of pyrite has taken place especially at times of low water load. It follows, then, that the pyrite-rich sediment load of streams fed by the waste of the Murgul deposit is currently a big threat to the aquatic life and environment and will continue to be so even after the closure of the deposit. In fact, the oxidation will be enhanced and acidity increased due to natural conditions, which necessitates strong remedial actions to be taken.

The national survey of natural radioactivity in concrete produced in Israel.

PubMed

Kovler, Konstantin

2017-03-01

The main goal of the current survey was to collect the results of the natural radiation tests of concrete produced in the country, to analyze the results statistically and make recommendations for further regulation on the national scale. Totally 109 concrete mixes produced commercially during the years 2012-2014 by concrete plants in Israel were analyzed. The average concentrations of NORM did not exceed the values recognized in the EU and were close to the values obtained from the Mediterranean countries such as Greece, Spain and Italy. It was also found that although the average value of the radon emanation coefficient of concrete containing coal fly ash (FA) was lower, than that of concrete mixes without FA, there was no significant difference between the indexes of both total radiation (addressing gamma radiation and radon together), and gamma radiation only, of the averages of the two sub-populations of concrete mixes: with and without FA. Copyright © 2016 Elsevier Ltd. All rights reserved.

Readability of HIV/AIDS educational materials: the role of the medium of communication, target audience, and producer characteristics.

PubMed

Wells, J A

1994-12-01

The reading difficulty of many HIV/AIDS brochures and pamphlets limits their effectiveness. This analysis addresses correlates of readability in 136 HIV/AIDS educational items. Readability is measured using the SMOG Index. The medium of communication is significantly related to readability: comic books and brochures are, on average, more readable than books and pamphlets (10.9 versus 11.9). The target audience also differentiates readability. Materials for HIV antibody test seekers, the general community, and sexually active adults have a more difficult reading grade, averaging 12.1, whereas materials for ethnic minorities average a more readable 9.2. The producer organization's type and location are unrelated to readability, but an AIDS-specific organizational focus correlates with better readability (grade 10.8 vs. 11.8). These findings remain significant in multivariate analysis. The results indicate that brochures and comics are more likely to be comprehended by low-literacy populations, that an understanding of the literacy of target audiences is needed to produce materials with appropriate reading levels, and that policies to influence producer organizations may result in the creation of more readable materials.

Cluster size dependence of high-order harmonic generation

NASA Astrophysics Data System (ADS)

Tao, Y.; Hagmeijer, R.; Bastiaens, H. M. J.; Goh, S. J.; van der Slot, P. J. M.; Biedron, S. G.; Milton, S. V.; Boller, K.-J.

2017-08-01

We investigate high-order harmonic generation (HHG) from noble gas clusters in a supersonic gas jet. To identify the contribution of harmonic generation from clusters versus that from gas monomers, we measure the high-order harmonic output over a broad range of the total atomic number density in the jet (from 3×1016 to 3 × 1018 {{cm}}-3) at two different reservoir temperatures (303 and 363 K). For the first time in the evaluation of the harmonic yield in such measurements, the variation of the liquid mass fraction, g, versus pressure and temperature is taken into consideration, which we determine, reliably and consistently, to be below 20% within our range of experimental parameters. By comparing the measured harmonic yield from a thin jet with the calculated corresponding yield from monomers alone, we find an increased emission of the harmonics when the average cluster size is less than 3000. Using g, under the assumption that the emission from monomers and clusters add up coherently, we calculate the ratio of the average single-atom response of an atom within a cluster to that of a monomer and find an enhancement of around 100 for very small average cluster size (∼200). We do not find any dependence of the cut-off frequency on the composition of the cluster jet. This implies that HHG in clusters is based on electrons that return to their parent ions and not to neighboring ions in the cluster. To fully employ the enhanced average single-atom response found for small average cluster sizes (∼200), the nozzle producing the cluster jet must provide a large liquid mass fraction at these small cluster sizes for increasing the harmonic yield. Moreover, cluster jets may allow for quasi-phase matching, as the higher mass of clusters allows for a higher density contrast in spatially structuring the nonlinear medium.

7 CFR 1001.62 - Announcement of producer prices.

Code of Federal Regulations, 2013 CFR

2013-01-01

... following prices and information: (a) The producer price differential; (b) The protein price; (c) The nonfat solids price; (d) The other solids price; (e) The butterfat price; (f) The average butterfat, protein... containing 3.5 percent butterfat computed by combining the Class III price and the producer price...

7 CFR 1001.62 - Announcement of producer prices.

Code of Federal Regulations, 2012 CFR

2012-01-01

... following prices and information: (a) The producer price differential; (b) The protein price; (c) The nonfat solids price; (d) The other solids price; (e) The butterfat price; (f) The average butterfat, protein... containing 3.5 percent butterfat computed by combining the Class III price and the producer price...

7 CFR 1001.62 - Announcement of producer prices.

Code of Federal Regulations, 2011 CFR

2011-01-01

... following prices and information: (a) The producer price differential; (b) The protein price; (c) The nonfat solids price; (d) The other solids price; (e) The butterfat price; (f) The average butterfat, protein... containing 3.5 percent butterfat computed by combining the Class III price and the producer price...

7 CFR 1001.62 - Announcement of producer prices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... following prices and information: (a) The producer price differential; (b) The protein price; (c) The nonfat solids price; (d) The other solids price; (e) The butterfat price; (f) The average butterfat, protein... containing 3.5 percent butterfat computed by combining the Class III price and the producer price...

7 CFR 1001.62 - Announcement of producer prices.

Code of Federal Regulations, 2014 CFR

2014-01-01

... following prices and information: (a) The producer price differential; (b) The protein price; (c) The nonfat solids price; (d) The other solids price; (e) The butterfat price; (f) The average butterfat, protein... containing 3.5 percent butterfat computed by combining the Class III price and the producer price...

Jerusalem artichoke powder: a useful material in producing high-optical-purity l-lactate using an efficient sugar-utilizing thermophilic Bacillus coagulans strain.

PubMed

Wang, Limin; Xue, Zhangwei; Zhao, Bo; Yu, Bo; Xu, Ping; Ma, Yanhe

2013-02-01

Jerusalem artichoke is a low-requirement crop, which does not interfere with food chain, and is a promising carbon source for industrial fermentation. Microbial conversion of such a renewable raw material to useful products, such as lactic acid, is an important objective in industrial biotechnology. In this study, high-optical-purity l-lactate was efficiently produced from the hydrolysates of Jerusalem artichoke powder by a thermophilic bacterium, Bacillus coagulans XZL4. High l-lactate production (134gl(-1)) was obtained using 267gl(-1) Jerusalem artichoke powder (total reducing sugars of 140gl(-1)) and 10gl(-1) of corn steep powder in fed-batch fermentation, with an average productivity of 2.5gl(-1)h(-1) and a yield of 0.96gg(-1) reducing sugars. The final product optical purity is 99%, which meets the requirement of lactic acid polymerization. Our study represents a cost-effective and promising method for polymer-grade l-lactate production using a cheap raw bio-resource. Copyright © 2012 Elsevier Ltd. All rights reserved.

Plasmoid Thruster for High Specific-Impulse Propulsion

NASA Technical Reports Server (NTRS)

Fimognari, Peter; Eskridge, Richard; Martin, Adam; Lee, Michael

2007-01-01

A report discusses a new multi-turn, multi-lead design for the first generation PT-1 (Plasmoid Thruster) that produces thrust by expelling plasmas with embedded magnetic fields (plasmoids) at high velocities. This thruster is completely electrodeless, capable of using in-situ resources, and offers efficiencies as high as 70 percent at a specific impulse, I(sub sp), of up to 8,000 s. This unit consists of drive and bias coils wound around a ceramic form, and the capacitor bank and switches are an integral part of the assembly. Multiple thrusters may be gauged to inductively recapture unused energy to boost efficiency and to increase the repetition rate, which, in turn increases the average thrust of the system. The thruster assembly can use storable propellants such as H2O, ammonia, and NO, among others. Any available propellant gases can be used to produce an I(sub sp) in the range of 2,000 to 8,000 s with a single-stage thruster. These capabilities will allow the transport of greater payloads to outer planets, especially in the case of an I(sub sp) greater than 6,000 s.

Identifying efficient dairy heifer producers using production costs and data envelopment analysis.

PubMed

Heinrichs, A J; Jones, C M; Gray, S M; Heinrichs, P A; Cornelisse, S A; Goodling, R C

2013-01-01

During November and December 2011, data were collected from 44 dairy operations in 13 Pennsylvania counties. Researchers visited each farm to collect information regarding management practices and feeding, and costs for labor, health, bedding, and reproduction for replacement heifers from birth until first calving. Costs per heifer were broken up into 4 time periods: birth until weaning, weaning until 6 mo of age, 6 mo of age until breeding age, and heifers from breeding to calving. Milk production records for each herd were obtained from Dairy Herd Improvement. The average number of milking cows on farms in this study was 197.8 ± 280.1, with a range from 38 to 1,708. Total cost averaged $1,808.23 ± $338.62 from birth until freshening. Raising calves from birth to weaning cost $217.49 ± 86.21; raising heifers from weaning age through 6 mo of age cost $247.38 ± 78.89; raising heifers from 6 mo of age until breeding cost $607.02 ± 192.28; and total cost for bred heifers was $736.33 ± 162.86. Feed costs were the largest component of the cost to raise heifers from birth to calving, accounting for nearly 73% of the total. Data envelopment analysis determined that 9 of the 44 farms had no inefficiencies in inputs or outputs. These farms best combined feed and labor investments, spending, on average, $1,137.40 and $140.62/heifer for feed and labor. These heifers calved at 23.7 mo of age and produced 88.42% of the milk produced by older cows. In contrast, the 35 inefficient farms spent $227 more on feed and $78 more on labor per heifer for animals that calved 1.6 mo later and produced only 82% of the milk made by their mature herdmates. Efficiency was attained by herds with the lowest input costs, but herds with higher input costs were also able to be efficient if age at calving was low and milk production was high for heifers compared with the rest of the herd. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The role of heterogeneity in contact timing and duration in network models of influenza spread in schools

PubMed Central

Toth, Damon J. A.; Leecaster, Molly; Pettey, Warren B. P.; Gundlapalli, Adi V.; Gao, Hongjiang; Rainey, Jeanette J.; Uzicanin, Amra; Samore, Matthew H.

2015-01-01

Influenza poses a significant health threat to children, and schools may play a critical role in community outbreaks. Mathematical outbreak models require assumptions about contact rates and patterns among students, but the level of temporal granularity required to produce reliable results is unclear. We collected objective contact data from students aged 5–14 at an elementary school and middle school in the state of Utah, USA, and paired those data with a novel, data-based model of influenza transmission in schools. Our simulations produced within-school transmission averages consistent with published estimates. We compared simulated outbreaks over the full resolution dynamic network with simulations on networks with averaged representations of contact timing and duration. For both schools, averaging the timing of contacts over one or two school days caused average outbreak sizes to increase by 1–8%. Averaging both contact timing and pairwise contact durations caused average outbreak sizes to increase by 10% at the middle school and 72% at the elementary school. Averaging contact durations separately across within-class and between-class contacts reduced the increase for the elementary school to 5%. Thus, the effect of ignoring details about contact timing and duration in school contact networks on outbreak size modelling can vary across different schools. PMID:26063821

Annular phased-array high-intensity focused ultrasound device for image-guided therapy of uterine fibroids.

PubMed

Held, Robert Thomas; Zderic, Vesna; Nguyen, Thuc Nghi; Vaezy, Shahram

2006-02-01

An ultrasound (US), image-guided high-intensity focused ultrasound (HIFU) device was developed for noninvasive ablation of uterine fibroids. The HIFU device was an annular phased array, with a focal depth range of 30-60 mm, a natural focus of 50 mm, and a resonant frequency of 3 MHz. The in-house control software was developed to operate the HIFU electronics drive system for inducing tissue coagulation at different distances from the array. A novel imaging algorithm was developed to minimize the HIFU-induced noise in the US images. The device was able to produce lesions in bovine serum albumin-embedded polyacrylamide gels and excised pig liver. The lesions could be seen on the US images as hyperechoic regions. Depths ranging from 30 to 60 mm were sonicated at acoustic intensities of 4100 and 6100 W/cm2 for 15 s each, with the latter producing average lesion volumes at least 63% larger than the former. Tissue sonication patterns that began distal to the transducer produced longer lesions than those that began proximally. The variation in lesion dimensions indicates the possible development of HIFU protocols that increase HIFU throughput and shorten tumor treatment times.

Quality monitoring of salt produced in Indonesia through seawater evaporation on HDPE geomembrane lined ponds

NASA Astrophysics Data System (ADS)

Jumaeri; Sulistyaningsih, T.; Alighiri, D.

2018-03-01

Salt is one of the primary ingredients that humans always need for various purposes, both for consumption and industry. The need for high-quality salt continues to increase, as long as industry growth. It must improve product quality through the development of salt production process technology. In this research, the quality monitoring of salt produced in Indonesia by evaporation of seawater on ponds lined using high-density polyethylene (HDPE) geomembrane has been studied. The manufacturing of salt carried out through the gradual precipitation principle on prepared ponds. HDPE geomembrane is used to coat evaporation ponds with viscosity 12-22°Be and crystallization ponds with a viscosity of 23°Be. The monitoring of the product is carried out in the particular periods during the salt production period. The result of control shows that the quality of salt produced in HDPE geomembrane coated salt ponds has an average NaCl content of 95.75%, so it has fulfilled with Indonesia National Standard (SNI), that is NaCl> 94.70%. The production of salt with HDPE geomembrane can improve the quality of salt product from NaCl 85.4% (conventional system) to 95.75%.

Nature of the lithospheric mantle beneath the Arabian Shield and genesis of Al-spinel micropods: Evidence from the mantle xenoliths of Harrat Kishb, Western Saudi Arabia

NASA Astrophysics Data System (ADS)

Ahmed, Ahmed H.; Moghazi, Abdel Kader M.; Moufti, Mohamed R.; Dawood, Yehia H.; Ali, Kamal A.

2016-01-01

The Harrat Kishb area of western Saudi Arabia is part of the Cenozoic volcanic fields in the western margin of the Arabian Shield. Numerous fresh ultramafic xenoliths are entrained in the basanite lava of Harrat Kishb, providing an opportunity to study the nature and petrogenetic processes involved in the evolution of the lithospheric mantle beneath the Arabian Shield. Based on the petrological characteristics and mineralogical compositions, the majority of the mantle xenoliths ( 92%) are peridotites (lherzolites and pyroxene-bearing harzburgites); the remaining xenoliths ( 8%) are unusual spinel-rich wehrlites containing black Al-spinel micropods. The two types of mantle xenoliths display magmatic protogranular texture. The peridotite xenoliths have high bulk-rock Mg#, high forsterite (Fo90-Fo92) and NiO (0.24-0.46 wt.%) contents of olivine, high clinopyroxene Mg# (0.91-0.93), variable spinel Cr# (0.10-0.49, atomic ratio), and approximately flat chondrite-normalized REE patterns. These features indicate that the peridotite xenoliths represent residues after variable degrees of melt extraction from fertile mantle. The estimated P (9-16 kbar) and T (877-1227 °C) as well as the oxidation state (ΔlogfO2 = - 3.38 to - 0.22) under which these peridotite xenoliths originated are consistent with formation conditions similar to most sub-arc abyssal-type peridotites worldwide. The spinel-rich wehrlite xenoliths have an unusual amount ( 30 vol.%) of Al-spinel as peculiar micropods with very minor Cr2O3 content (< 1 wt.%). Olivines of the spinel-rich wehrlites have low-average Fo (Fo81) and NiO (0.18 wt.%) contents, low-average cpx Mg# (0.79), high average cpx Al2O3 content (8.46 wt.%), and very low-average spinel Cr# (0.01). These features characterize early mantle cumulates from a picritic melt fraction produced by low degrees of partial melting of a garnet-bearing mantle source. The relatively high Na2O and Al2O3 contents of cpx suggest that the spinel-rich wehrlites are formed under high P (11-14 kbar), T (1090-1130 °C), and oxidation state (ΔlogfO2 FMQ = + 0.14 to + 0.37), which occurred slightly below the crust-mantle boundary. The REE patterns of spinel-rich wehrlites are almost similar to those of the associated peridotite xenoliths, which confirm at least a spatial genetic linkage between them. Regarding the formation of Al-spinel micropods in spinel-rich wehrlite cumulates, it is suggested that the melt-rock reaction mechanism is not the only process by which podiform chromitite is formed. Early fractionation of picritic melts produced by partial melting of a mantle source under high P-T conditions could be another mechanism. The cpx composition, not opx, as it was assumed, seems to be the main control of the size and composition of spinel concentrations.

40 CFR 421.262 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... pollutant property Maximum for any 1 day Maximum for monthly average mg/troy ounce of precious metals... day Maximum for monthly average mg/troy ounce of precious metal in the granulated raw material Copper... monthly average mg/troy ounce of gold produced by cyanide stripping Copper 7.030 3.700 Cyanide (total) 1...

Effects of rumen-inert fat on lactation, reproduction, and health of high producing Holstein herds.

PubMed

Scott, T A; Shaver, R D; Zepeda, L; Yandell, B; Smith, T R

1995-11-01

Two hundred twenty of 443 cows freshening between June 1989 and March 1990 in five commercial Holstein herds were fed .45 kg/d of rumen-inert fat from calving until 200 DIM. Control diets were fed as TMR and contained, on average, 3.7 to 4.8% supplemental fat (DM basis). Test herds had rolling herd averages of 9300 to 13,250 kg of milk. Production of 4% FCM and milk increased 1.01 (3.3%) and 1.50 kg/d (4.6%), respectively, for primiparous cows fed additional fat. Multiparous cows from four herds demonstrated no response; multiparous cows in one herd increased production of 4% FCM by 2.88 kg/d (8.2%), milk by 2.45 kg/d (6.4%), and milk fat by .14kg/d (10.6%) in response to additional fat. An explanation of response differences among herd for multiparous cows was not possible. For primiparous and multiparous cows, increased genetic potential increased treatment response. Increased body condition score at calving influenced treatment response of multiparous cows. Thinner cows produced more milk and less milk fat in response to additional dietary fat than did fatter cows. Most reproductive indices were unaffected by treatment. Cows receiving additional fat had lower, but nonsignificantly lower, incidences of most health disorders. Responses to rumen-inert fat by cows receiving high concentrations of dietary fat were marginal and were affected by body condition score at calving and by genetic potential.

Optimal ventilatory patterns in periodic breathing.

PubMed

Ghazanshahi, S D; Khoo, M C

1993-01-01

The goal of this study was to determine whether periodic breathing (PB), which is highly prevalent during sleep at high altitudes, imposes physiological penalties on the respiratory system in the absence of any accompanying disease. Using a computer model of respiratory gas exchange, we compared the effects of a variety of PB patterns on the chemical and mechanical costs of breathing to those resulting from regular tidal breathing. Although PB produced considerable fluctuation in arterial blood gas tensions, for the same cycle-averaged ventilation, higher arterial oxygen saturation and lower arterial carbon dioxide levels were achieved. This result can be explained by the fact that the combination of large breaths and apnea in PB leads to a substantial reduction in dead space ventilation. At the same time, the savings in mechanical cost achieved by the respiratory muscles during apnea partially offset the increase during the breathing phase. Consequently, the "pressure cost," a criterion based on mean inspiratory pressure, was elevated only slightly, although the average work rate of breathing increased significantly. We found that, at extreme altitudes, PB patterns with clusters of 2 to 4 large breaths that alternate with apnea produce the highest arterial oxygenation levels and lowest pressure costs. The common occurrence of PB patterns with closely similar features has been reported in sleeping healthy sojourners at extreme altitudes. Taken together, these findings suggest that PB favors a reduction in the oxygen demands of the respiratory muscles and therefore may not be as detrimental as it is generally believed to be.

Reproductive success of Macrotermes bellicosus (Isoptera, Macrotermitinae) in two neighbouring habitats.

PubMed

Korb, Judith; Linsenmair, Karl Eduard

1999-02-01

The fungus-cultivating, mound-building termite Macrotermes bellicosus can reach high densities in African savannah habitats, whereas in forests it is comparatively rare and is only found in relatively open areas. Earlier studies in the Comoé National Park (Côte d'Ivoire, West Africa) suggested that this might be because ambient temperatures are lower in the forest than the savannah. Therefore, forests seem to be suboptimal habitats. During 3 consecutive years we measured relevant fitness parameters in both habitats to test this hypothesis. Colonies in the savannah had higher reproductive outputs. They reproduced annually, producing high numbers of offspring (alates), whereas forest colonies reproduced on average only once every 3 years and even then only low numbers of alates were produced. Annual growth of mound height, which can be regarded as an indicator of colony growth, varied considerably between individual colonies and years. Nevertheless, in two years the growth rate of mounds in the shrub savannah was higher than that of mounds in the gallery forest. Unexpectedly, survival probability as calculated by Kaplan Meier analysis was much lower for colonies in the shrub savannah than for colonies in the gallery forest. Using these data in a computer simulation we calculated lifetime reproductive success (LRS) for an average colony in both habitats. As LRS was much higher for colonies in the shrub savannah than in the gallery forest, these results confirmed our suggestion that the forest is a suboptimal habitat for M. bellicosus.

Monthly mean simulation experiments with a course-mesh global atmospheric model

NASA Technical Reports Server (NTRS)

Spar, J.; Klugman, R.; Lutz, R. J.; Notario, J. J.

1978-01-01

Substitution of observed monthly mean sea-surface temperatures (SSTs) as lower boundary conditions, in place of climatological SSTs, failed to improve the model simulations. While the impact of SST anomalies on the model output is greater at sea level than at upper levels the impact on the monthly mean simulations is not beneficial at any level. Shifts of one and two days in initialization time produced small, but non-trivial, changes in the model-generated monthly mean synoptic fields. No improvements in the mean simulations resulted from the use of either time-averaged initial data or re-initialization with time-averaged early model output. The noise level of the model, as determined from a multiple initial state perturbation experiment, was found to be generally low, but with a noisier response to initial state errors in high latitudes than the tropics.

Cost-effective poster and print production with digital camera and computer technology.

PubMed

Chen, M Y; Ott, D J; Rohde, R P; Henson, E; Gelfand, D W; Boehme, J M

1997-10-01

The purpose of this report is to describe a cost-effective method for producing black-and-white prints and color posters within a radiology department. Using a high-resolution digital camera, personal computer, and color printer, the average cost of a 5 x 7 inch (12.5 x 17.5 cm) black-and-white print may be reduced from $8.50 to $1 each in our institution. The average cost for a color print (8.5 x 14 inch [21.3 x 35 cm]) varies from $2 to $3 per sheet depending on the selection of ribbons for a color-capable laser printer and the paper used. For a 30-panel, 4 x 8 foot (1.2 x 2.4 m) standard-sized poster, the cost for materials and construction is approximately $100.

Airborne DIAL Ozone and Aerosol Trends Observed at High Latitudes Over North America from February to May 2000

NASA Technical Reports Server (NTRS)

Hair, Jonathan W.; Browell, Edward V.; Butler, Carolyn F.; Grant, William B.; DeYoung, Russell J.; Fenn, Marta A.; Brackett, Vince G.; Clayton, Marian B.; Brasseur, Lorraine

2002-01-01

Ozone (O3) and aerosol scattering ratio profiles were obtained from airborne lidar measurements on thirty-eight aircraft flights over seven aircraft deployments covering the latitudes of 40 deg.-85 deg.N between 4 February and 23 May 2000 as part of the TOPSE (Tropospheric Ozone Production about the Spring Equinox) field experiment. The remote and in situ O3 measurements were used together to produce a vertically-continuous O3 profile from near the surface to above the tropopause. Ozone, aerosol, and potential vorticity (PV) distributions were used together to identify the presence of pollution plumes and stratospheric intrusions. The number of observed pollution plumes was found to increase into the spring along with a significant increase in aerosol loading. Ozone was found to increase in the middle free troposphere (4-6 km) at high latitudes (60 deg.-85 deg. N) by an average of 4.3 ppbv/mo from about 55 ppbv in early February to over 72 ppbv in mid-May. The average aerosol scattering ratios in the same region increased at an average rate of 0.37/mo from about 0.35 to over 1.7. Ozone and aerosol scattering were highly correlated over entire field experiment. Based on the above results and the observed aircraft in-situ measurements, it was estimated that stratospherically-derived O3 accounted for less than 20% of the observed increase in mid tropospheric O3 at high latitudes. The primary cause of the observed O3 increase was found to be the photochemical production of O3 in pollution plumes.

Direct Aqueous Photochemistry of Isoprene High-NOx Secondary Organic Aerosol

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Tran B.; Laskin, Alexander; Laskin, Julia

2012-05-17

Secondary organic aerosol (SOA) generated from the high-NOx photooxidation of isoprene was dissolved in water and irradiated with {lambda} > 290 nm light to simulate direct photolytic processing of organics in atmospheric water droplets. High-resolution mass spectrometry was used to characterize the composition at four time intervals (0, 1, 2, and 4 h). Photolysis resulted in the decomposition of high molecular weight (MW) oligomers, reducing the average length of organics by 2 carbon units. Approximately 65% by count of SOA molecules decomposed during photolysis, accompanied by the formation of new products. An average of 30 % of the organic massmore » was modified after 4 h of direct photolysis. In contrast, only a small fraction of the mass (<2 %), belonging primarily to organic nitrates, decomposed in the absence of irradiation by hydrolysis. We observed a statistically-significant increase in average O/C, decrease in H/C, and increase in N/C ratios resulting from photolysis. Furthermore, the concentration of aromatic compounds increased significantly during photolysis. Approximately 10 % of photodegraded compounds and 50 % of the photoproducts contain nitrogen. Organic nitrates and multifunctional oligomers were identified as compounds degraded by photolysis. Low-MW 0N (compounds with 0 nitrogen atoms in their structure) and 2N compounds were the dominant photoproducts. Fragmentation experiments using tandem mass spectrometry (MSn, n = 2-3) indicate that the 2N products are likely heterocyclic/aromatic and are tentatively identified as furoxans. Although the exact mechanism is unclear, these 2N heterocyclic compounds are produced by reactions between photochemically-formed aqueous NOx species and SOA organics.« less

The JLab high power ERL light source

NASA Astrophysics Data System (ADS)

Neil, G. R.; Behre, C.; Benson, S. V.; Bevins, M.; Biallas, G.; Boyce, J.; Coleman, J.; Dillon-Townes, L. A.; Douglas, D.; Dylla, H. F.; Evans, R.; Grippo, A.; Gruber, D.; Gubeli, J.; Hardy, D.; Hernandez-Garcia, C.; Jordan, K.; Kelley, M. J.; Merminga, L.; Mammosser, J.; Moore, W.; Nishimori, N.; Pozdeyev, E.; Preble, J.; Rimmer, R.; Shinn, M.; Siggins, T.; Tennant, C.; Walker, R.; Williams, G. P.; Zhang, S.

2006-02-01

A new THz/IR/UV photon source at Jefferson Lab is the first of a new generation of light sources based on an Energy-Recovered, (superconducting) Linac (ERL). The machine has a 160 MeV electron beam and an average current of 10 mA in 75 MHz repetition rate hundred femtosecond bunches. These electron bunches pass through a magnetic chicane and therefore emit synchrotron radiation. For wavelengths longer than the electron bunch the electrons radiate coherently a broadband THz ˜ half cycle pulse whose average brightness is >5 orders of magnitude higher than synchrotron IR sources. Previous measurements showed 20 W of average power extracted [Carr, et al., Nature 420 (2002) 153]. The new facility offers simultaneous synchrotron light from the visible through the FIR along with broadband THz production of 100 fs pulses with >200 W of average power. The FELs also provide record-breaking laser power [Neil, et al., Phys. Rev. Lett. 84 (2000) 662]: up to 10 kW of average power in the IR from 1 to 14 μm in 400 fs pulses at up to 74.85 MHz repetition rates and soon will produce similar pulses of 300-1000 nm light at up to 3 kW of average power from the UV FEL. These ultrashort pulses are ideal for maximizing the interaction with material surfaces. The optical beams are Gaussian with nearly perfect beam quality. See www.jlab.org/FEL for details of the operating characteristics; a wide variety of pulse train configurations are feasible from 10 ms long at high repetition rates to continuous operation. The THz and IR system has been commissioned. The UV system is to follow in 2005. The light is transported to user laboratories for basic and applied research. Additional lasers synchronized to the FEL are also available. Past activities have included production of carbon nanotubes, studies of vibrational relaxation of interstitial hydrogen in silicon, pulsed laser deposition and ablation, nitriding of metals, and energy flow in proteins. This paper will present the status of the system and discuss some of the discoveries we have made concerning the physics performance, design optimization, and operational limitations of such a first generation high power ERL light source.

The effect of laser pulse tailored welding of Inconel 718

NASA Technical Reports Server (NTRS)

Mccay, T. Dwayne; Mccay, Mary Helen; Sharp, C. Michael; Womack, Michael G.

1990-01-01

Pulse tailored laser welding has been applied to wrought, wrought grain grown, and cast Inconel 718 using a CO2 laser. Prior to welding, the material was characterized metallographically and the solid state transformation regions were identified using Differential Scanning Calorimetry and high temperature x-ray diffraction. Bead on plate welds (restrained and unrestrained) were then produced using a matrix of pulse duty cycles and pulsed average power. Subsequent characterization included heat affected zone width, penetration and underbead width, the presence of cracks, microfissures and porosity, fusion zone curvature, and precipitation and liquated region width. Pedigree welding on three selected processing conditions was shown by microstructural and dye penetrant analysis to produce no microfissures, a result which strongly indicates the viability of pulse tailored welding for microfissure free IN 718.

Characterization of Polyhydroxyalkanoate Produced by Bacillus megaterium VB89 Isolated from Nisargruna Biogas Plant.

PubMed

Baikar, Vishakha; Rane, Ashwini; Deopurkar, Rajendra

2017-09-01

Polyhydroxyalkanoates (PHAs) are naturally occurring biodegradable polymers that can curb the extensive use of polypropylene based plastics. In contrast to chemically synthesized polypropylene plastics, PHAs are biodegradable and thus environmentally safe. PHAs have attracted much attention as biocompatible and biodegradable thermoplastics. The present study involves isolation of bacteria from different environments capable of synthesizing PHAs. The bacterium producing highest yield of PHA (0.672 ± 0.041 g/L) was identified as Bacillus megaterium VB89 by biochemical and molecular techniques such as 16S rDNA sequence analysis. Strain VB89 produced polyhydroxybutyrate (PHB) as revealed by FTIR and NMR. This PHB had an average molecular weight of 2.89 × 10 5  Da and a polydispersity index of 2.37. Thermal properties of the PHB included a glass transition temperature of 13.97 °C, a melting temperature of 181.74 °C, and a decomposition temperature of 234 °C. All these properties indicated that VB89 produced PHB of high purity and good thermal stability.

Origin Of The Light Neutral Boson Observed In Heavy Ion Collisions

NASA Astrophysics Data System (ADS)

El-Nagdy, M. S.; Abdelsalam, A.; Badawy, B. M.

2007-02-01

We report the results of (e+ e- pairs) produced during the interactions of 200A GeV 32S with emulsion nuclei. The results for the electron pairs suggest that they originate from light neutral bosons emitted during the collision. The origin of such neutral bosons could be due to de-excitation of the produced fragments 4He, 8Be and 12C resulting in 32S fragmentation. The masses of the neutral bosons were estimated from electron kinematics and found to be equal 1.51±0.14 and 9.88±2.85 MeV/c2 and life time of orders 10-16 - 10-15 s. The data and results obtained could explain and put conclusion to the puzzles which were going on during the last 50 years around the anomalous mean free path of α-particles produced during high energy particle collisions. The depression of average shower particle multiplicities produced in the collisions of secondary helium fragments as compared to those of primary helium at similar energy signs the possibility of formation of the neutral boson.

Design of a high-bunch-charge 112-MHz superconducting RF photoemission electron source

DOE PAGES

Xin, T.; Brutus, J. C.; Belomestnykh, Sergey A.; ...

2016-09-01

High-bunch-charge photoemission electron-sources operating in a continuous wave (CW) mode are required for many advanced applications of particle accelerators, such as electron coolers for hadron beams, electron-ion colliders, and free-electron lasers (FELs). Superconducting RF (SRF) has several advantages over other electron-gun technologies in CW mode as it offers higher acceleration rate and potentially can generate higher bunch charges and average beam currents. A 112 MHz SRF electron photoinjector (gun) was developed at Brookhaven National Laboratory (BNL) to produce high-brightness and high-bunch-charge bunches for the Coherent electron Cooling Proof-of-Principle (CeC PoP) experiment. Lastly, the gun utilizes a quarter-wave resonator (QWR) geometrymore » for assuring beam dynamics, and uses high quantum efficiency (QE) multi-alkali photocathodes for generating electrons.« less

Long-term preservation of eri and ailanthus silkworms using frozen gonads.

PubMed

Fukumori, Hisayoshi; Lee, Jung; Fujii, Tsuguru; Kajiura, Zenta; Banno, Yutaka

2017-08-01

Cryopreservation of eri and ailanthus silkworms using frozen gonads was investigated. First, we evaluated the freeze tolerance of ovary and testis in the eri silkworm, which showed high tolerance. Mating between frozen ovary-transplanted females and frozen testis-transplanted males produced 163.0 eggs, yielding 105.7 larvae per moth. In a second experiment, we tested the use of the eri silkworm as a host insect for gonad transplantation from ailanthus silkworm donors. A high success ratio for laid and hatched eggs was demonstrated for ovary transplantation (97.8 and 51.3 eggs per moth, respectively). For testis transplantation, however, the average number of hatched larvae was low (12.0). Mating between host eri females and males in which both frozen ovary and testis of the ailanthus silkworm had been transplanted produced 6.4 fertilized eggs per host moth. Our success in using cross subspecies cryopreservation between these wild silkworms could lead to the alternative use of hosts between species in other insects. Copyright © 2017 Elsevier Inc. All rights reserved.

Effect of PS-PVD production throughput on Si nanoparticles for negative electrode of lithium ion batteries

NASA Astrophysics Data System (ADS)

Ohta, R.; Fukada, K.; Tashiro, T.; Dougakiuchi, M.; Kambara, M.

2018-03-01

Silicon nanoparticles (Si-NPs) have been produced by plasma spray physical vapor deposition at throughput as high as 1 kg h-1 (17 g min-1) and the effect on the battery performance is investigated. When the Si powder feed-rate is changed from 1 to 17 g min-1, although the average primary particle size increases to 50 nm, the cycle capacity of the batteries using these Si-NPs is improved slightly owing to their less agglomerated structure. In contrast, when Ni is added to Si feedstock, the cycle capacity is improved at 1 g min-1 due to modified Si-NP structure having SiNi2 interface. Whereas, the batteries with the Si-NP produced at 17 g min-1 shows significant decrease in the cycle capacity because of the excess Ni silicide formation that is resulted from the elevated co-condensation point and the increased reaction area at high throughputs despite the constant Ni concentration in the feedstock.

Grace DAKASEP alkaline battery separator

NASA Technical Reports Server (NTRS)

Giovannoni, R. T.; Lundquist, J. T.; Choi, W. M.

1987-01-01

The Grace DAKASEP separator was originally developed as a wicking layer for nickel-zinc alkaline batteries. The DAKASEP is a filled non-woven separator which is flexible and heat sealable. Through modification of formulation and processing variables, products with a variety of properties can be produced. Variations of DAKASEP were tested in Ni-H2, Ni-Zn, Ni-Cd, and primary alkaline batteries with good results. The properties of DAKASEP which are optimized for Hg-Zn primary batteries are shown in tabular form. This separator has high tensile strength, 12 micron average pore size, relatively low porosity at 46-48 percent, and consequently moderately high resistivity. Versions were produced with greater than 70 percent porosity and resistivities in 33 wt percent KOH as low as 3 ohm cm. Performance data for Hg-Zn E-1 size cells containing DAKASEP with the properties shown in tabular form, are more reproducible than data obtained with a competitive polypropylene non-woven separator. In addition, utilization of active material is in general considerably improved.

Osmium isotopic tracing of atmospheric emissions from an aluminum smelter

NASA Astrophysics Data System (ADS)

Gogot, Julien; Poirier, André; Boullemant, Amiel

2015-09-01

We present for the first time the use of osmium isotopic composition as a tracer of atmospheric emissions from an aluminum smelter, where alumina (extracted from bauxite) is reduced through electrolysis into metallic aluminum using carbonaceous anodes. These anodes are consumed in the process; they are made of petroleum coke and pitch and have high Re/Os elementary ratio. Due to the relatively large geological age of their source material, their osmium shows a high content of radiogenic 187Os produced from in situ187Re radioactive decay. The radiogenic isotopic composition (187Os/188Os ∼ 2.5) of atmospheric particulate emissions from this smelter is different from that of other typical anthropogenic osmium sources (that come from ultramafic geological contexts with unradiogenic Os isotopes, e.g., 187Os/188Os < 0.2) and also different from average eroding continental crust 187Os/188Os ratios (ca. 1.2). This study demonstrates the capacity of osmium measurements to monitor particulate matter emissions from the Al-producing industry.

40 CFR 80.825 - How is the refinery or importer annual average toxics value determined?

Code of Federal Regulations, 2010 CFR

2010-07-01

... number of batches of gasoline produced or imported during the averaging period. i = Individual batch of... toxics value, Ti, of each batch of gasoline is determined using the Phase II Complex Model specified at...

Picosecond laser with 11 W output power at 1342 nm based on composite multiple doping level Nd:YVO4 crystal

NASA Astrophysics Data System (ADS)

Rodin, Aleksej M.; Grishin, Mikhail; Michailovas, Andrejus

2016-01-01

We report results of design and optimization of high average output power picosecond and nanosecond laser operating at 1342 nm wavelength. Developed for selective micromachining, this DPSS laser is comprised of master oscillator, regenerative amplifier and output pulse control module. Passively mode-locked by means of semiconductor saturable absorber mirror and pumped with 808 nm wavelength Nd:YVO4 master oscillator emits 12.5 ps pulses at repetition rate of 55 MHz with average output power of ∼100 mW. The four-pass confocal delay line forms a longest part of the oscillator cavity in order to suppress thermo-mechanical misalignment. Picked from the train seed pulses were injected to the cavity of regenerative amplifier based on composite Nd:YVO4 crystal with diffusion-bonded segments of multiple Nd doping concentration end-pumped at 880 nm wavelength. Laser produces pulses of ∼13 ps duration at 300 kHz repetition rate with average output power of 11 W and nearly diffraction limited beam quality of M2∼1.03. Attained high peak power ∼2.8 MW facilitates conversion to the 2nd, 3rd and 6th harmonics at 671 nm, 447 nm and 224 nm wavelengths with 80%, 50% and 15% efficiency respectively. Without seeding the regenerative amplifier transforms to electro-optically cavity-dumped Q-switched laser providing 10 ns output pulses at high repetition rates with beam propagation factor of M2∼1.06.

Force systems in the initial phase of orthodontic treatment -- a comparison of different leveling arch wires.

PubMed

Fuck, Lars-Michael; Drescher, Dieter

2006-01-01

The determination of orthodontically-effective forces and moments places great demands on the technical equipment. Many patients report severe pain after fixed appliance insertion. Since it is assumed that pain from orthodontic appliances is associated with the force and moment levels applied to the teeth and since the occurrence of root resorption is a common therapeutic side effect, it would seem important to know the actual magnitudes of the components of the active orthodontic force systems. The aim of the present study was therefore to measure initial force systems produced by different leveling arch-wires in a complete multi-bracket appliance and to assess whether force and moment levels can be regarded as biologically acceptable or not. The actual bracket position in 42 patients was transferred onto a measurement model. Forces and moments produced by a super-elastic nickel-titanium (NiTi) archwire, a 6-strand stainless steel archwire, and a 7-strand super-elastic NiTi archwire were determined experimentally on different teeth. Average forces and moments produced by the super-elastic NiTi arch wires were found to be the highest. In spite if their larger diameter, the stranded arch wires' average force and moment levels were lower, especially that of the stranded super-elastic archwire. Nevertheless, maximum force levels sometimes exceeded recommended values in the literature and must be considered as too high. The measured arch wires' initial force systems differed significantly depending on the type of archwire and its material structure. Stranded arch wires produced lower force and moment levels, and we recommend their use in the initial phase of orthodontic treatment.

Anisotropy of anomalous diffusion improves the accuracy of differentiating low- and high-grade cerebral gliomas.

PubMed

Xu, Boyan; Su, Lu; Wang, Zhenxiong; Fan, Yang; Gong, Gaolang; Zhu, Wenzhen; Gao, Peiyi; Gao, Jia-Hong

2018-04-17

Anomalous diffusion model has been introduced and shown to be beneficial in clinical applications. However, only the directionally averaged values of anomalous diffusion parameters were investigated, and the anisotropy of anomalous diffusion remains unexplored. The aim of this study was to demonstrate the feasibility of using anisotropy of anomalous diffusion for differentiating low- and high-grade cerebral gliomas. Diffusion MRI images were acquired from brain tumor patients and analyzed using the fractional motion (FM) model. Twenty-two patients with histopathologically confirmed gliomas were selected. An anisotropy metric for the FM-related parameters, including the Noah exponent (α) and the Hurst exponent (H), was introduced and their values were statistically compared between the low- and high-grade gliomas. Additionally, multivariate logistic regression analysis was performed to assess the combination of the anisotropy metric and the directionally averaged value for each parameter. The diagnostic performances for grading gliomas were evaluated using a receiver operating characteristic (ROC) analysis. The Hurst exponent H was more anisotropic in high-grade than in low-grade gliomas (P = 0.015), while no significant difference was observed for the anisotropy of α. The ROC analysis revealed that larger areas under the ROC curves were produced for the combination of α (1) and the combination of H (0.813) compared with the directionally averaged α (0.979) and H (0.594), indicating an improved performance for tumor differentiation. The anisotropy of anomalous diffusion can provide distinctive information and benefit the differentiation of low- and high-grade gliomas. The utility of anisotropic anomalous diffusion may have an improved effect for investigating pathological changes in tissues. Copyright © 2018 Elsevier Inc. All rights reserved.

Averaging interval selection for the calculation of Reynolds shear stress for studies of boundary layer turbulence.

NASA Astrophysics Data System (ADS)

Lee, Zoe; Baas, Andreas

2013-04-01

It is widely recognised that boundary layer turbulence plays an important role in sediment transport dynamics in aeolian environments. Improvements in the design and affordability of ultrasonic anemometers have provided significant contributions to studies of aeolian turbulence, by facilitating high frequency monitoring of three dimensional wind velocities. Consequently, research has moved beyond studies of mean airflow properties, to investigations into quasi-instantaneous turbulent fluctuations at high spatio-temporal scales. To fully understand, how temporal fluctuations in shear stress drive wind erosivity and sediment transport, research into the best practice for calculating shear stress is necessary. This paper builds upon work published by Lee and Baas (2012) on the influence of streamline correction techniques on Reynolds shear stress, by investigating the time-averaging interval used in the calculation. Concerns relating to the selection of appropriate averaging intervals for turbulence research, where the data are typically non-stationary at all timescales, are well documented in the literature (e.g. Treviño and Andreas, 2000). For example, Finnigan et al. (2003) found that underestimating the required averaging interval can lead to a reduction in the calculated momentum flux, as contributions from turbulent eddies longer than the averaging interval are lost. To avoid the risk of underestimating fluxes, researchers have typically used the total measurement duration as a single averaging period. For non-stationary data, however, using the whole measurement run as a single block average is inadequate for defining turbulent fluctuations. The data presented in this paper were collected in a field study of boundary layer turbulence conducted at Tramore beach near Rosapenna, County Donegal, Ireland. High-frequency (50 Hz) 3D wind velocity measurements were collected using ultrasonic anemometry at thirteen different heights between 0.11 and 1.62 metres above the bed. A technique for determining time-averaging intervals for a series of anemometers stacked in a close vertical array is presented. A minimum timescale is identified using spectral analysis to determine the inertial sub-range, where energy is neither produced nor dissipated but passed down to increasingly smaller scales. An autocorrelation function is then used to derive a scaling pattern between anemometer heights, which defines a series of averaging intervals of increasing length with height above the surface. Results demonstrate the effect of different averaging intervals on the calculation of Reynolds shear stress and highlight the inadequacy of using the total measurement duration as a single block average. Lee, Z. S. & Baas, A. C. W. (2012). Streamline correction for the analysis of boundary layer turbulence. Geomorphology, 171-172, 69-82. Treviño, G. and Andreas, E.L., 2000. Averaging Intervals For Spectral Analysis Of Nonstationary Turbulence. Boundary-Layer Meteorology, 95(2): 231-247. Finnigan, J.J., Clement, R., Malhi, Y., Leuning, R. and Cleugh, H.A., 2003. Re-evaluation of long-term flux measurement techniques. Part I: Averaging and coordinate rotation. Boundary-Layer Meteorology, 107(1): 1-48.

Heavy rainfall in Mediterranean cyclones. Part I: contribution of deep convection and warm conveyor belt

NASA Astrophysics Data System (ADS)

Flaounas, Emmanouil; Kotroni, Vassiliki; Lagouvardos, Konstantinos; Gray, Suzanne L.; Rysman, Jean-François; Claud, Chantal

2018-04-01

In this study, we provide an insight to the role of deep convection (DC) and the warm conveyor belt (WCB) as leading processes to Mediterranean cyclones' heavy rainfall. To this end, we use reanalysis data, lighting and satellite observations to quantify the relative contribution of DC and the WCB to cyclone rainfall, as well as to analyse the spatial and temporal variability of these processes with respect to the cyclone centre and life cycle. Results for the period 2005-2015 show that the relationship between cyclone rainfall and intensity has high variability and demonstrate that even intense cyclones may produce low rainfall amounts. However, when considering rainfall averages for cyclone intensity bins, a linear relationship was found. We focus on the 500 most intense tracked cyclones (responsible for about 40-50% of the total 11-year Mediterranean rainfall) and distinguish between the ones producing high and low rainfall amounts. DC and the WCB are found to be the main cause of rainfall for the former (producing up to 70% of cyclone rainfall), while, for the latter, DC and the WCB play a secondary role (producing up to 50% of rainfall). Further analysis showed that rainfall due to DC tends to occur close to the cyclones' centre and to their eastern sides, while the WCBs tend to produce rainfall towards the northeast. In fact, about 30% of rainfall produced by DC overlaps with rainfall produced by WCBs but this represents only about 8% of rainfall produced by WCBs. This suggests that a considerable percentage of DC is associated with embedded convection in WCBs. Finally, DC was found to be able to produce higher rain rates than WCBs, exceeding 50 mm in 3-h accumulated rainfall compared to a maximum of the order of 40 mm for WCBs. Our results demonstrate in a climatological framework the relationship between cyclone intensity and processes that lead to heavy rainfall, one of the most prominent environmental risks in the Mediterranean. Therefore, we set perspectives for a deeper analysis of the favourable atmospheric conditions that yield high impact weather.

Towards a more consistent picture of isopycnal mixing in climate models

NASA Astrophysics Data System (ADS)

Gnanadesikan, A.; Pradal, M. A. S.; Koszalka, I.; Abernathey, R. P.

2014-12-01

The stirring of tracers by mesoscale eddies along isopycnal surfaces is often represented in coarse-resolution models by the Redi diffusion parameter ARedi. Theoretical treatments of ARedi often assume it should scale as the eddy energy or the growth rate of mesoscale eddies,. producing a picture where it is high in boundary currents and low )of order a few hundred m2/s) in the gyre interiors. However, observational estimates suggest that ARedi should be very large (of order thousands of m2/s) in the gyre interior. We present results of recent simulations comparing a range of spatially constant values ARedi (with values of 400, 800, 1200 and 2400 m2/s) to a spatially resolved estimate based on altimetry and a zonally averaged version of the same estimate. In general, increasing the ARedi coefficient destratifies and warms the high latitudes. Relative to our control simulation, the spatially dependent coefficient is lower in the Southern Ocean, but high in the North Pacific, and so the temperature changes mirror this. We also examine the response of ocean hypoxia to these changes. In general, the zonally averaged version of the altimetry-based estimate of ARedi does not capture the full 2d representation.

A Public Health Opportunity Found in Food Waste

PubMed Central

Upadhyaya, Mudita; Bounds, Gregory; Markham, Christine

2017-01-01

A food waste problem coexists with food insecurity and obesity. Brighter Bites, a school-based food cooperative program, successfully channels primarily donated produce to low-income communities and provides nutrition education, creating an increased demand for and intake of fruits and vegetables. We present the framework used in Brighter Bites and results of operationalizing this framework during 3 years of implementation in Houston, Texas. Results demonstrated that, during 2013 through 2016, more than 12,500 families enrolled in Brighter Bites for 16 weeks in the school year. More than 90% of the produce was donated. Each week, families received on average 54 to 61 servings of fresh produce with the average cost of produce being $2.53 per family per week. Of those parents who completed the process surveys, more than 80% reported the produce to be effective in improving their children’s diet. Brighter Bites demonstrates a successful model to address food waste and improve dietary habits of underserved families. PMID:29101766

Evidence of biphonation and source-filter interactions in the bugles of male North American wapiti (Cervus canadensis).

PubMed

Reby, D; Wyman, M T; Frey, R; Passilongo, D; Gilbert, J; Locatelli, Y; Charlton, B D

2016-04-15

With an average male body mass of 320 kg, the wapiti, ITALIC! Cervus canadensis, is the largest extant species of Old World deer (Cervinae). Despite this large body size, male wapiti produce whistle-like sexual calls called bugles characterised by an extremely high fundamental frequency. Investigations of the biometry and physiology of the male wapiti's relatively large larynx have so far failed to account for the production of such a high fundamental frequency. Our examination of spectrograms of male bugles suggested that the complex harmonic structure is best explained by a dual-source model (biphonation), with one source oscillating at a mean of 145 Hz (F0) and the other oscillating independently at an average of 1426 Hz (G0). A combination of anatomical investigations and acoustical modelling indicated that the F0 of male bugles is consistent with the vocal fold dimensions reported in this species, whereas the secondary, much higher source at G0 is more consistent with an aerodynamic whistle produced as air flows rapidly through a narrow supraglottic constriction. We also report a possible interaction between the higher frequency G0 and vocal tract resonances, as G0 transiently locks onto individual formants as the vocal tract is extended. We speculate that male wapiti have evolved such a dual-source phonation to advertise body size at close range (with a relatively low-frequency F0 providing a dense spectrum to highlight size-related information contained in formants) while simultaneously advertising their presence over greater distances using the very high-amplitude G0 whistle component. © 2016. Published by The Company of Biologists Ltd.

Compact x-ray source based on burst-mode inverse Compton scattering at 100 kHz

DOE PAGES

Graves, W.  S.; Bessuille, J.; Brown, P.; ...

2014-12-01

A design for a compact x-ray light source (CXLS) with flux and brilliance orders of magnitude beyond existing laboratory scale sources is presented. The source is based on inverse Compton scattering of a high brightness electron bunch on a picosecond laser pulse. The accelerator is a novel high-efficiency standingwave linac and rf photoinjector powered by a single ultrastable rf transmitter at X-band rf frequency. The high efficiency permits operation at repetition rates up to 1 kHz, which is further boosted to 100 kHz by operating with trains of 100 bunches of 100 pC charge, each separated by 5 ns. Themore » entire accelerator is approximately 1 meter long and produces hard x rays tunable over a wide range of photon energies. The colliding laser is a Yb:YAG solid-state amplifier producing 1030 nm, 100 mJ pulses at the same 1 kHz repetition rate as the accelerator. The laser pulse is frequency-doubled and stored for many passes in a ringdown cavity to match the linac pulse structure. At a photon energy of 12.4 keV, the predicted x-ray flux is 5 × 10¹¹ photons/second in a 5% bandwidth and the brilliance is 2 × 10¹² photons/(sec mm² mrad² 0.1%) in pulses with rms pulse length of 490 fs. The nominal electron beam parameters are 18 MeV kinetic energy, 10 microamp average current, 0.5 microsecond macropulse length, resulting in average electron beam power of 180 W. Optimization of the x-ray output is presented along with design of the accelerator, laser, and x-ray optic components that are specific to the particular characteristics of the Compton scattered x-ray pulses.« less

Comparison of Thraustochytrids Aurantiochytrium sp., Schizochytrium sp., Thraustochytrium sp., and Ulkenia sp. for production of biodiesel, long-chain omega-3 oils, and exopolysaccharide.

PubMed

Lee Chang, Kim Jye; Nichols, Carol Mancuso; Blackburn, Susan I; Dunstan, Graeme A; Koutoulis, Anthony; Nichols, Peter D

2014-08-01

Heterotrophic growth of thraustochytrids has potential in coproducing biodiesel for transportation, as well as producing a feedstock for omega-3 long-chain (≥C20) polyunsaturated fatty acids (LC-PUFA), especially docosahexaenoic acid (DHA) for use in nutraceuticals. In this study, we compared eight new endemic Australian thraustochytrid strains from the genera Aurantiochytrium, Schizochytrium, Thraustochytrium, and Ulkenia for the synthesis of exopolysaccharide (EPS), in addition to biodiesel and LC-PUFA. Aurantiochytrium sp. strains readily utilized glucose for biomass production, and increasing glucose from 2 to 4 % w/v of the culture medium resulted in increased biomass yield by an average factor of 1.7. Ulkenia sp. strain TC 010 and Thraustochytrium sp. strain TC 033 did not utilize glucose, while Schizochytrium sp. strain TC 002 utilized less than half the glucose available by day 14, and Thraustochytrium sp. strain TC 004 utilized glucose at 4 % w/v but not 2 % w/v of the culture suggesting a threshold requirement between these values. Across all strains, increasing glucose from 2 to 4 % w/v of the culture medium resulted in increased total fatty acid methyl ester content by an average factor of 1.9. Despite an increasing literature demonstrating the capacity of thraustochytrids for DHA synthesis, the production of EPS from these organisms is not well documented. A broad range of EPS yields was observed. The maximum yield of EPS was observed for Schizochytrium sp. strain TC 002 (299 mg/L). High biomass-producing strains that also have high lipid and high EPS yield may be better candidates for commercial production of biofuels and other coproducts.

Preschool speech error patterns predict articulation and phonological awareness outcomes in children with histories of speech sound disorders.

PubMed

Preston, Jonathan L; Hull, Margaret; Edwards, Mary Louise

2013-05-01

To determine if speech error patterns in preschoolers with speech sound disorders (SSDs) predict articulation and phonological awareness (PA) outcomes almost 4 years later. Twenty-five children with histories of preschool SSDs (and normal receptive language) were tested at an average age of 4;6 (years;months) and were followed up at age 8;3. The frequency of occurrence of preschool distortion errors, typical substitution and syllable structure errors, and atypical substitution and syllable structure errors was used to predict later speech sound production, PA, and literacy outcomes. Group averages revealed below-average school-age articulation scores and low-average PA but age-appropriate reading and spelling. Preschool speech error patterns were related to school-age outcomes. Children for whom >10% of their speech sound errors were atypical had lower PA and literacy scores at school age than children who produced <10% atypical errors. Preschoolers who produced more distortion errors were likely to have lower school-age articulation scores than preschoolers who produced fewer distortion errors. Different preschool speech error patterns predict different school-age clinical outcomes. Many atypical speech sound errors in preschoolers may be indicative of weak phonological representations, leading to long-term PA weaknesses. Preschoolers' distortions may be resistant to change over time, leading to persisting speech sound production problems.

Whole-Body Counter(WBC) and food radiocesium contamination surveys in Namie, Fukushima Prefecture.

PubMed

Hosokawa, Yoichiro; Nomura, Kazuki; Tsushima, Eiki; Kudo, Kohsei; Noto, Yuka; Nishizawa, Yoshiko

2017-01-01

This study examined the internal Cs exposure of residents and the Cs present in food products produced in Namie. Whole-body counter (WBC) was used for the measurement of internal exposure per each whole body of examinees. The food products which appeared to be used for consumption, were brought by residents and commercially available food items were excluded. Most of them were wild plants or food items produced by residents. Four years of data from April 2012 to March 2013 (fiscal 2012) and April 2015 to March 2016 (Fiscal 2015) were analyzed and studied. The average radioactivity measured by WBC was approximately 5 Bq for Cs-134, and 20 Bq for Cs-137 and the average committed effective dose was approximately 1 μSv. The average for the residents with detectable radioactivity was 25 μSv, and the human health effects are considered to be extremely low risk. However, the radioactivity of the affected individuals showed a higher value than the theoretical attenuation rate. The majority (83.2%) of individuals exhibiting radioactivity were over 50 years old. The number of food products brought in for detection decreased as the study period progressed, but the number of food products with radioactivity had increased. While the items with a higher detection rate of radioactivity included fruits such as citron and persimmon, shiitake mushrooms exhibited the highest radioactivity. Moreover, the radioactivity of seven items in these 10 items decreased from fiscal 2012 to fiscal 2015. Mushrooms had high radioactivity and were produced over a wide area. We suggest that the elderly try to enjoy life and eat wild plants in moderation while inspecting food products. Therefore, we will continue to work in raising awareness of radiation and its potential presence in food products and thus the continuing necessity of monitoring radioactivity in food in the future.

Cowpeas and pinto beans: yields and light efficiency of candidate space crops in the Laboratory Biosphere closed ecological system

NASA Astrophysics Data System (ADS)

Nelson, M.; Dempster, W. F.; Silverstone, S.; Alling, A.; Allen, J. P.; van Thillo, M.

An experiment utilizing cowpeas Vigna unguiculata pinto beans Phaseolus vulgaris L and Apogee ultra-dwarf wheat was conducted in the soil-based closed ecological facility Laboratory Biosphere from February to May 2005 The lighting regime was 13 hours light 11 hours dark at a light intensity of 960 mu mol m -2 s -1 45 moles m -2 day -1 supplied by high-pressure sodium lamps The pinto beans and cowpeas were grown at two different plant densities The pinto bean produced 710 g m -2 total aboveground biomass and 341 g m -2 at 33 5 plants per m 2 and at 37 5 plants per m 2 produced 1092 g m -2 total biomass and 537 g m -2 of dry seed an increase of almost 50 Cowpeas at 28 plants m -2 yielded 1060 g m -2 of total biomass and 387 g seed m -2 outproducing the less dense planting by more than double 209 in biomass and 86 more seed as the planting of 21 plants m -2 produced 508 g m-2 of total biomass and 209 g m-2 of seed Edible yield rate EYR for the denser cowpea bean was 4 6 g m -2 day -1 vs 2 5 g m -2 day -1 for the less dense stand average yield was 3 5 g m -2 day -1 EYR for the denser pinto bean was 8 5 g m -2 day -1 vs 5 3 g m -2 day -1 average EYR for the pinto beans was 7 0 g m -2 day -1 Yield efficiency rate YER the ratio of edible to non-edible biomass was 0 97 for the dense pinto bean 0 92 for the less dense pinto bean and average 0 94 for the entire crop The cowpeas

Whole-Body Counter(WBC) and food radiocesium contamination surveys in Namie, Fukushima Prefecture

PubMed Central

Nomura, Kazuki; Tsushima, Eiki; Kudo, Kohsei; Noto, Yuka; Nishizawa, Yoshiko

2017-01-01

Purpose This study examined the internal Cs exposure of residents and the Cs present in food products produced in Namie. Whole-body counter (WBC) was used for the measurement of internal exposure per each whole body of examinees. Methods The food products which appeared to be used for consumption, were brought by residents and commercially available food items were excluded. Most of them were wild plants or food items produced by residents. Four years of data from April 2012 to March 2013 (fiscal 2012) and April 2015 to March 2016 (Fiscal 2015) were analyzed and studied. Results The average radioactivity measured by WBC was approximately 5 Bq for Cs-134, and 20 Bq for Cs-137 and the average committed effective dose was approximately 1 μSv. The average for the residents with detectable radioactivity was 25 μSv, and the human health effects are considered to be extremely low risk. However, the radioactivity of the affected individuals showed a higher value than the theoretical attenuation rate. The majority (83.2%) of individuals exhibiting radioactivity were over 50 years old. The number of food products brought in for detection decreased as the study period progressed, but the number of food products with radioactivity had increased. While the items with a higher detection rate of radioactivity included fruits such as citron and persimmon, shiitake mushrooms exhibited the highest radioactivity. Moreover, the radioactivity of seven items in these 10 items decreased from fiscal 2012 to fiscal 2015. Mushrooms had high radioactivity and were produced over a wide area. Conclusion We suggest that the elderly try to enjoy life and eat wild plants in moderation while inspecting food products. Therefore, we will continue to work in raising awareness of radiation and its potential presence in food products and thus the continuing necessity of monitoring radioactivity in food in the future. PMID:28334042

Dust deposition in southern Nevada and California, 1984-1989: Relations to climate, source area, and source lithology

NASA Astrophysics Data System (ADS)

Reheis, Marith C.; Kihl, Rolf

1995-05-01

Dust samples collected annually for 5 years from 55 sites in southern Nevada and California provide the first regional source of information on modern rates of dust deposition, grain size, and mineralogical and chemical composition relative to climate and to type and lithology of dust source. The average silt and clay flux (rate of deposition) in southern Nevada and southeastern California ranges from 4.3 to 15.7 g/m2/yr, but in southwestern California the average silt and clay flux is as high as 30 g/m2/yr. The climatic factors that affect dust flux interact with each other and with the factors of source type (playas versus alluvium), source lithology, geographic area, and human disturbance. Average dust flux increases with mean annual temperature but is not correlated to decreases in mean annual precipitation because the regional winds bring dust to relatively wet areas. In contrast, annual dust flux mostly reflects changes in annual precipitation (relative drought) rather than temperature. Although playa and alluvial sources produce about the same amount of dust per unit area, the total volume of dust from the more extensive alluvial sources is much larger. In addition, playa and alluvial sources respond differently to annual changes in precipitation. Most playas produce dust that is richer in soluble salts and carbonate than that from alluvial sources (except carbonate-rich alluvium). Gypsum dust may be produced by the interaction of carbonate dust and anthropogenic or marine sulfates. The dust flux in an arid urbanizing area may be as much as twice that before disturbance but decreases when construction stops. The mineralogic and major-oxide composition of the dust samples indicates that sand and some silt is locally derived and deposited, whereas clay and some silt from different sources can be far-traveled. Dust deposited in the Transverse Ranges of California by the Santa Ana winds appears to be mainly derived from sources to the north and east.

Reservoir compaction of the Belridge Diatomite and surface subsidence, south Belridge field, Kern County, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowersox, J.R.; Shore, R.A.

1990-05-01

Surface subsidence due to reservoir compaction during production has been observed in many large oil fields. Subsidence is most obvious in coastal and offshore fields where inundation by the sea occurs. Well-known examples are Wilmington field in California and Ekofisk field in the North Sea. In South Belridge field, the Belridge Diatomite member of the late Miocene Reef Ridge Shale has proven prone to compaction during production. The reservoir, a high-porosity, low-permeability, highly compressive rock composed largely of diatomite and mudstone, is about 1,000 ft thick and lies at an average depth of 1,600 ft. Within the Belridge Diatomite, reservoirmore » compaction due to withdrawal of oil and water in Sec. 12, T28S, R20E, MDB and M, was noticed after casing failures in producing wells began occurring and tension cracks, enlarged by hydrocompaction after a heavy rainstorm were observed. Surface subsidence in Sec. 12 has been monitored since April 1987, through the surveying of benchmark monuments. The average annualized subsidence rate during 1987 was {minus}1.86 ft/yr, {minus}0.92 ft/yr during 1988, and {minus}0.65 ft/yr during 1989; the estimated peak subsidence rate reached {minus}7.50 ft/yr in July 1985, after 1.5 yrs of production from the Belridge Diatomite reservoir. Since production from the Belridge Diatomite reservoir commenced in February 1984, the surface of the 160-ac producing area has subsided about 12.5 ft. This equates to an estimated reservoir compaction of 30 ft in the Belridge Diatomite and an average loss of reservoir porosity of 2.4% from 55.2 to 52.8%. Injection of water for reservoir pressure maintenance in the Belridge diatomite began in June 1987, and has been effective in mitigating subsidence to current rates and repressurizing the reservoir to near-initial pressure. An added benefit of water injection has been improved recovery of oil from the Belridge Diatomite by waterflood.« less

The acute effect of exercise modality and nutrition manipulations on post-exercise resting energy expenditure and respiratory exchange ratio in women: a randomized trial.

PubMed

Wingfield, Hailee L; Smith-Ryan, Abbie E; Melvin, Malia N; Roelofs, Erica J; Trexler, Eric T; Hackney, Anthony C; Weaver, Mark A; Ryan, Eric D

2015-12-01

The purpose of this study was to examine the effect of exercise modality and pre-exercise carbohydrate (CHO) or protein (PRO) ingestion on post-exercise resting energy expenditure (REE) and respiratory exchange ratio (RER) in women. Twenty recreationally active women (mean ± SD; age 24.6 ± 3.9 years; height 164.4 ± 6.6 cm; weight 62.7 ± 6.6 kg) participated in this randomized, crossover, double-blind study. Each participant completed six exercise sessions, consisting of three exercise modalities: aerobic endurance exercise (AEE), high-intensity interval running (HIIT), and high-intensity resistance training (HIRT); and two acute nutritional interventions: CHO and PRO. Salivary samples were collected before each exercise session to determine estradiol-β-17 and before and after to quantify cortisol. Post-exercise REE and RER were analyzed via indirect calorimetry at the following: baseline, immediately post (IP), 30 minutes (30 min) post, and 60 minutes (60 min) post exercise. A mixed effects linear regression model, controlling for estradiol, was used to compare mean longitudinal changes in REE and RER. On average, HIIT produced a greater REE than AEE and HIRT (p < 0.001) post exercise. Effects of AEE and HIRT were not significantly different for post-exercise REE (p = 0.1331). On average, HIIT produced lower RER compared to either AEE or HIRT after 30 min (p < 0.001 and p = 0.0169, respectively) and compared to AEE after 60 min (p = 0.0020). On average, pre-exercise PRO ingestion increased post-exercise REE (p = 0.0076) and decreased post-exercise RER (p < 0.0001) compared to pre-exercise CHO ingestion. HIIT resulted in the largest increase in REE and largest reduction in RER.

Environmental Gradient Analysis, Ordination, and Classification in Environmental Impact Assessments.

DTIC Science & Technology

1987-09-01

agglomerative clustering algorithms for mainframe computers: (1) the unweighted pair-group method that V uses arithmetic averages ( UPGMA ), (2) the...hierarchical agglomerative unweighted pair-group method using arithmetic averages ( UPGMA ), which is also called average linkage clustering. This method was...dendrograms produced by weighted clustering (93). Sneath and Sokal (94), Romesburg (84), and Seber• (90) also strongly recommend the UPGMA . A dendrogram

Propagation method for persistent high yield of diverse Listeria phages on permissive hosts at refrigeration temperatures.

PubMed

Radford, Devon R; Ahmadi, Hanie; Leon-Velarde, Carlos G; Balamurugan, Sampathkumar

2016-10-01

The efficient production of a high concentration of bacteriophage in large volumes has been a limiting factor in the exploration of the true potential of these organisms for biotechnology, agriculture and medicine. Traditional methods focus on generating small volumes of highly concentrated samples as the end product of extensive mechanical and osmotic processing. To function at an industrial scale mandates extensive investment in infrastructure and input materials not feasible for many smaller facilities. To address this, we developed a novel, scalable, generic method for producing significantly higher titer psychrophilic phage (P < 2.0 × 10(-6)), 2- to 4-fold faster than traditional methods. We generate renewable high yields from single source cultures by propagating phage under refrigeration conditions in which Listeria, Yersinia and their phages grow in equilibrium. Diverse Yersinia and Listeria phages tested yielded averages of 3.49 × 10(8) to 3.36 × 10(12) PFU/ml/day compared to averages of 1.28 × 10(5) to 1.30 × 10(10) PFU/ml/day by traditional methods. Host growth and death kinetics made this method ineffective for extended propagation of mesophilic phages. Crown Copyright © 2016. Published by Elsevier Masson SAS. All rights reserved.

76 FR 42113 - Purified Carboxymethylcellulose From Mexico: Final Results of Antidumping Duty Administrative Review

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-18

..., 2011) (Preliminary Results). The review covers one producer/ exporter, Quimica Amtex S.A. de C.V. The..., through June 30, 2010, is as follows: Weighted- Producer/exporter average margin (percentage) Quimica...

Underground and ground-level particulate matter concentrations in an Italian metro system

NASA Astrophysics Data System (ADS)

Cartenì, Armando; Cascetta, Furio; Campana, Stefano

2015-01-01

All around the world, many studies and experimental results have assessed elevated concentrations of Particulate Matter (PM) in underground metro systems, with non-negligible implications for human health due to protracted exposure to fine particles. Starting from this consideration, an intensive particulate sampling campaign was carried out in January 2014 measuring the PM concentrations in the Naples (Italy) Metro Line 1, both at station platforms and inside trains. Naples Metro Line 1 is about 18 km long, with 17 stations (3 ground-level and 14 below-ground ones). Experimental results show that the average PM10 concentrations measured in the underground station platforms range between 172 and 262 μg/m3 whilst the average PM2.5 concentrations range between 45 and 60 μg/m3. By contrast, in ground-level stations no significant difference between stations platforms and urban environment measurements was observed. Furthermore, a direct correlation between trains passage and PM concentrations was observed, with an increase up to 42% above the average value. This correlation is possibly caused by the re-suspension of the particles due to the turbulence induced by trains. The main original finding was the real-time estimations of PM levels inside the trains travelling both in ground-level and underground sections of Line 1. The results show that high concentrations of both PM10 (average values between 58 μg/m3 and 138 μg/m3) and PM2.5 (average values between 18 μg/m3 and 36 μg/m3) were also measured inside trains. Furthermore, measurements show that windows left open on trains caused the increase in PM concentrations inside trains in the underground section, while in the ground-level section the clean air entering the trains produced an environmental "washing effect". Finally, it was estimated that every passenger spends on average about 70 min per day exposed to high levels of PM.

Mercury from chlor-alkali plants: measured concentrations in food product sugar.

PubMed

Dufault, Renee; LeBlanc, Blaise; Schnoll, Roseanne; Cornett, Charles; Schweitzer, Laura; Wallinga, David; Hightower, Jane; Patrick, Lyn; Lukiw, Walter J

2009-01-26

Mercury cell chlor-alkali products are used to produce thousands of other products including food ingredients such as citric acid, sodium benzoate, and high fructose corn syrup. High fructose corn syrup is used in food products to enhance shelf life. A pilot study was conducted to determine if high fructose corn syrup contains mercury, a toxic metal historically used as an anti-microbial. High fructose corn syrup samples were collected from three different manufacturers and analyzed for total mercury. The samples were found to contain levels of mercury ranging from below a detection limit of 0.005 to 0.570 micrograms mercury per gram of high fructose corn syrup. Average daily consumption of high fructose corn syrup is about 50 grams per person in the United States. With respect to total mercury exposure, it may be necessary to account for this source of mercury in the diet of children and sensitive populations.

Molecular insights of genetic variation in milk thistle (Silybum marianum [L.] Gaertn.) populations collected from southwest Iran.

PubMed

Rafizadeh, Azam; Koohi-Dehkordi, Mehrana; Sorkheh, Karim

2018-06-07

Milk thistle (Silybum marianum) is among the world's popular medicinal plants. Start Codon Targeted (SCoT) marker system was utilized to investigate the genetic variability of 80 S. marianum genotypes from eight populations in Iran. SCoT marker produced 255 amplicons and 84.03% polymorphism was generated. The SCoT marker system's polymorphism information content value was 0.43. The primers' resolving power values were between 4.18 and 7.84. The percentage of polymorphic bands was between 33.3 and 100%. The Nei's gene diversity (h) was 0.19-1.30 with an average 0.72. The Shannon's index (I) ranged from 0.29 to 1.38 with an average value of 0.83. The average gene flow (0.37) demonstrated a high genetic variation among the studied populations. The variation of 42% was displayed by the molecular variance analysis among the populations while a recorded variation of 58% was made within the populations. Current investigation suggested that SCoT marker system could effectively evaluate milk thistle genotypes genetic diversity.

Electron Microscopic Observations of Rabbit Antibodies.

PubMed

Hall, C E; Nisonoff, A; Slayter, H S

1959-12-01

Electron micrographs were obtained showing the individual, shadow-cast macromolecules from solutions of purified anti-p-azobenzoate rabbit antibody and of normal gamma-globulin. The two materials look alike and consist mainly of asymmetrical rod-like particles about 30 to 40 A in diameter. Lengths are not constant but the weight average is about 250 A for the antibodies and about 200 A for the gamma-globulin. The average observed dimensions are reasonably consistent with values deduced from physical-chemical methods, although the shape is more nearly that of a cylindrical rod rather than the ellipsoid employed in hydrodynamical theory. Mixtures of antibody and specific dihaptenic dye were examined in attempts to establish the mode of the specific aggregation. At the high dilutions necessary for electron microscopy (0.1 mg./ml.), the effect of the dye was small and tended to be masked by non-specific aggregation on drying. The evidence suggests that under these conditions the specific reaction involves an end-to-end aggregation of the elementary particles to produce a weight average length about twice that of the pure antibody.

Low energy single-staged anaerobic fluidized bed ceramic membrane bioreactor (AFCMBR) for wastewater treatment.

PubMed

Aslam, Muhammad; McCarty, Perry L; Shin, Chungheon; Bae, Jaeho; Kim, Jeonghwan

2017-09-01

An aluminum dioxide (Al 2 O 3 ) ceramic membrane was used in a single-stage anaerobic fluidized bed ceramic membrane bioreactor (AFCMBR) for low-strength wastewater treatment. The AFCMBR was operated continuously for 395days at 25°C using a synthetic wastewater having a chemical oxygen demand (COD) averaging 260mg/L. A membrane net flux as high as 14.5-17L/m 2 h was achieved with only periodic maintenance cleaning, obtained by adding 25mg/L of sodium hypochlorite solution. No adverse effect of the maintenance cleaning on organic removal was observed. An average SCOD in the membrane permeate of 23mg/L was achieved with a 1h hydraulic retention time (HRT). Biosolids production averaged 0.014±0.007gVSS/gCOD removed. The estimated electrical energy required to operate the AFCMBR system was 0.039kWh/m 3 , which is only about 17% of the electrical energy that could be generated with the methane produced. Copyright © 2017 Elsevier Ltd. All rights reserved.

Metaphase yields from staphylococcal enterotoxin A stimulated peripheral blood lymphocytes of unirradiated and irradiated aged rhesus monkeys

NASA Technical Reports Server (NTRS)

Hill, F. S.; Cox, A. B.; Salmon, Y. L.; Cantu, A. O.; Lucas, J. N.

1994-01-01

The mitogen phytohemagglutinin (PHA) works well in both human and cynomolgus monkey (Macaca fascicularis) lymphocyte cultures to stimulate T cell proliferation. T cells from rhesus monkeys (Macaca mulatta) are less responsive than human cells, producing few metaphases when thousands are required, e.g. in biological dosimetry studies. We show that staphylococcal enterotoxin A (SEA), one of the most potent mitogens known, at a concentration of 0.5 microgram/ml stimulated peripheral lymphocytes to grow with a mitotic index (MI) averaging 0.13 metaphases/cell in old, irradiated rhesus macaques. This was significantly greater (p < 0.001) than that produced by PHA (MI < 0.01) in lymphocytes from the same animals. Whole blood was cultured for 96, 120 and 144 h for five irradiated individuals and for two controls. All cells cultured with SEA produced a high MI with a peak response at 120 h whereas the same cultures showed low MI for each PHA stimulated culture.

Highly Efficient Agrobacterium-Mediated Transformation of Wheat Via In Planta Inoculation

NASA Astrophysics Data System (ADS)

Risacher, Thierry; Craze, Melanie; Bowden, Sarah; Paul, Wyatt; Barsby, Tina

This chapter details a reproducible method for the transformation of spring wheat using Agrobacterium tumefaciens via the direct inoculation of bacteria into immature seeds in planta as described in patent WO 00/63398(1. Transformation efficiencies from 1 to 30% have been obtained and average efficiencies of at least 5% are routinely achieved. Regenerated plants are phenotypically normal with 30-50% of transformation events carrying introduced genes at single insertion sites, a higher rate than is typically reported for transgenic plants produced using biolistic transformation methods.

Thermosensitive period of sex determination in the coral-reef damselfish Acanthochromis polyacanthus and the implications of projected ocean warming

NASA Astrophysics Data System (ADS)

Rodgers, G. G.; Donelson, J. M.; Munday, P. L.

2017-03-01

Higher temperatures associated with climate change have the potential to significantly alter the population sex ratio of species with temperature-dependent sex determination. Whether or not elevated temperature affects sex determination depends on both the absolute temperature experienced and the stage of development at which the thermal conditions occur. We explored the importance of exposure timing during early development in the coral reef fish, Acanthochromis polyacanthus, by increasing water temperature 1.5 or 3 °C above the summer average (28.5 °C) at different stages of development. We also measured the effect of treatment temperature on fish size and condition, in order to gauge how the thermal threshold for sex-ratio bias may compare with other commonly considered physiological metrics. Increasing grow-out temperature from 28.5 to 30 °C had no effect on the sex ratio of offspring, whereas an increase to 31.5 °C (+3 °C) produced a strong male bias (average 90%). The thermosensitive period for this species lasted between 25 and 60 d post hatching, with the bias in sex ratio greater the earlier that fish experienced warm conditions. Temperatures high enough to bias the sex ratio are likely to be seen first during late summer (January and February) and would affect clutches produced late in the breeding season. There was no change to fish condition in response to temperature; however, the two higher temperature treatments produced significantly smaller fish at sampling. Clutches produced early in the season could buffer the population from a skewed sex ratio, as their development will remain below the thermal threshold; however, continued ocean warming could mean that clutches produced earlier in the breeding season would also be affected in the longer term. A skewed sex ratio could be detrimental to population viability by reducing the number of females in the breeding population.

The vulnerability of commercial aircraft avionics to carbon fibers

NASA Technical Reports Server (NTRS)

Meyers, J. A.; Salmirs, S.

1980-01-01

Avionics components commonly used in commercial aircraft were tested for vulnerability to failure when operated in an environment with a high density of graphite fibers. The components were subjected to a series of exposures to graphite fibers of different lengths. Lengths used for the tests were (in order) 1 mm, 3 mm, and 10 mm. The test procedure included subjecting the equipment to characteristic noise and shock environments. Most of the equipment was invulnerable or did not fail until extremely high average exposures were reached. The single exception was an air traffic control transponder produced in the early 1960's. It had the largest case open area through which fibers could enter and it had no coated boards.

High power infrared super-Gaussian beams: generation, propagation, and application

NASA Astrophysics Data System (ADS)

du Preez, Neil C.; Forbes, Andrew; Botha, Lourens R.

2008-10-01

In this paper we present the design of a CO2 laser resonator that produces as the stable transverse mode a super-Gaussian laser beam. The resonator makes use of an intra-cavity diffractive mirror and a flat output coupler, generating the desired intensity profile at the output coupler with a flat wavefront. We consider the modal build-up in such a resonator and show that such a resonator mode has the ability to extract more energy from the cavity that a standard cavity single mode beam (e.g., Gaussian mode cavity). We demonstrate the design experimentally on a high average power TEA CO2 laser for paint stripping applications.

Direct Solvothermal Liquefaction of Pennisetum purpureum Biomass to Produce Biocrude Using Ethanol Solvent

NASA Astrophysics Data System (ADS)

Adriane Ochiai, Mikael; Marrod Cruz, Salvador; Oporto, Louiellyn; de Leon, Rizalinda

2018-03-01

Direct solvothermal liquefaction was used in converting the lignocellulosic biomass, Pennisetum purpureum or Napier grass using ethanol as solvent. Liquefaction of Napier grass resulted in a dark and viscous bio-crude product and exhibited promising yields (34.6377% to 48.6267%). It was determined that the effects of temperature and residence time were statistically significant with the residence time having the greatest positive effect on yield. High yields of bio-crude from Napier grass seem to occur when solvothermal temperature, residence time increased and as solids ratio decreased. However, elemental analysis showed that the bio-crude produced needs to undergo deoxygenation (O: 14.25 - 49.42%) before mixing with petroleum. For the higher heating value (HHV), the parameters observed in the study were statistically insignificant, however, temperature was determined to have the greatest positive effect on HHV. It was observed that high HHV bio-crude were produced at high temperatures, low solids ratio, and low residence times. The acquired averages for the HHV (20.0333 MJ/kg to 29.7744 MJ/kg) were all higher than the HHV of the Napier grass sample used in the study (12.9394 MJ/kg). It was observed in the study, that even though solids ratio has the least effect on both responses, the choice of solids ratio is dependent on its interaction effects with the other parameters as its effects contribute to the observed responses.

Longer Hospice Stays Associated With Decreased End-Of-Life Spending For Patients In Regions With High Expenditures

PubMed Central

Wang, Shi-Yi; Hsu, Sylvia H.; Huang, Siwan; Soulos, Pamela R.; Gross, Cary P.

2018-01-01

Hospice is expected to decrease end-of-life care expenditures yet evidence for its financial impact remains inconclusive. One potential explanation is that hospice enrollment may produce differential cost saving effects by region, due to geographic variation in end-of-life care spending patterns. Accordingly, we examined 103,745 elderly Medicare fee-for-service beneficiaries in the Surveillance, Epidemiology, and End Results-Medicare database who died from cancer in 2004–2011. We created quintiles by the mean end-of-life expenditure per hospital referral region (HRR), and examined HRR-level variation in the associations between length of hospice enrollment and expenditures among quintiles. Results showed that longer hospice stays were associated with decreased end-of-life expenditures for patients residing in regions of high average expenditures, but not for those in regions with low average expenditures. Hospice use accounted for 8.0% of the expenditure variation between the highest and lowest quintile areas, demonstrating the powers and limitations of hospice use for cost saving. PMID:28167723

Characterisation of aroma profiles of commercial soy sauce by odour activity value and omission test.

PubMed

Feng, Yunzi; Su, Guowan; Zhao, Haifeng; Cai, Yu; Cui, Chun; Sun-Waterhouse, Dongxiao; Zhao, Mouming

2015-01-15

Twenty-seven commercial soy sauces produced through three different fermentation processes (high-salt liquid-state fermentation soy sauce, HLFSS; low-salt solid-state fermentation soy sauce, LSFSS; Koikuchi soy sauce, KSS) were examined to identify the aroma compounds and the effect of fermentation process on the flavour of the soy sauce was investigated. Results showed that 129 volatiles were identified, of which 41 aroma-active components were quantified. The types of odorants occurring in the three soy sauce groups were similar, although their intensities significantly differed. Many esters and phenols were found at relatively high intensities in KSS, whereas some volatile acids only occurred in LSFSS. Furthermore, 23 aroma compounds had average OAVs>1, among which 3-methylbutanal, ethyl acetate, 4-hydroxy-2-ethyl-5-methyl-3(2H)-furanone, 2-methylbutanal and 3-(methylthio)propanal exhibited the highest average OAVs (>100). In addition, omission tests verified the important contribution of the products resulting from amino acid catabolism to the characteristic aroma of soy sauce. Copyright © 2014. Published by Elsevier Ltd.

Rumination time as a potential predictor of common diseases in high-productive Holstein dairy cows.

PubMed

Moretti, Riccardo; Biffani, Stefano; Tiezzi, Francesco; Maltecca, Christian; Chessa, Stefania; Bozzi, Riccardo

2017-11-01

We examined the hypothesis that rumination time (RT) could serve as a useful predictor of various common diseases of high producing dairy cows and hence improve herd management and animal wellbeing. We measured the changes in rumination time (RT) in the days before the recording of diseases (specifically: mastitis, reproductive system diseases, locomotor system issues, and gastroenteric diseases). We built predictive models to assess the association between RT and these diseases, using the former as the outcome variable, and to study the effects of the latter on the former. The average Pseudo-R 2 of the fitted models was moderate to low, and this could be due to the fact that RT is influenced by other additional factors which have a greater effect than the predictors used here. Although remaining in a moderate-to-low range, the average Pseudo-R 2 of the models regarding locomotion issues and gastroenteric diseases was higher than the others, suggesting the greater effect of these diseases on RT. The results are encouraging, but further work is needed if these models are to become useful predictors.

Study of the Emission Characteristics of Single-Walled CNT and Carbon Nano-Fiber Pyrograf III

NASA Astrophysics Data System (ADS)

Mousa, Marwan S.; Al-Akhras, M.-Ali H.; Daradkeh, Samer

2018-02-01

Field emission microscopy measurements from Single-Walled Carbon Nanotubes (SWCNTs) and Carbon Nano-Fibers Pyrograf III PR-1 (CNF) were performed. Details of the materials employed in the experiments are as follows: (a) Carbon Nano-Fibers Pyrograf III PR-1 (CNF), having an average fiber diameter that is ranging between (100-200) nm with a length of (30-100) μm. (b) Single walled Carbon Nanotubes were produced by high-pressure CO over Fe particle (HiPCO: High-Pressure Carbon Monoxide process), having an average diameter ranging between (1-4) nm with a length of (1-3) μm. The experiments were performed under vacuum pressure value of (10-7 mbar). The research work reported here includes the field electron emission current-voltage (I-V) characteristics and presented as Fowler-Nordheim (FN) plots and the spatial emission current distributions (electron emission images) obtained and analyzed in terms of electron source features. For both the SWCNT and the CNF a single spot pattern for the electron spatial; distributions were observed.

The 27-28 October 1986 FIRE IFO cirrus case study - Cloud optical properties determined by High Spectral Resolution Lidar

NASA Technical Reports Server (NTRS)

Grund, C. J.; Eloranta, E. W.

1990-01-01

The High Spectral Resolution Lidar (HSRL) was operated from a roof-top site in Madison, Wisconsin. The transmitter configuration used to acquire the case study data produces about 50 mW of ouput power and achieved eye-safe, direct optical depth, and backscatter cross section measurements with 10 min averaging times. A new continuously pumped, injection seeded, frequency doubled Nd:YAG laser transmitter reduces time-averaging constraints by a factor of about 10, while improving the aerosol-molecular signal separation capabilities and wavelength stability of the instrument. The cirrus cloud backscatter-phase functions have been determined for the October 27-28, 1986 segment of the HSRL FIRE dataset. Features exhibiting backscatter cross sections ranging over four orders of magnitude have been observed within this 33 h period. During this period, cirrus clouds were observed with optical thickness ranging from 0.01 to 1.4. The altitude relationship between cloud top and bottom boundaries and the optical center of the cloud is influenced by the type of formation observed.

Averaging peak-to-peak voltage detector for absolute mass determination of single particles with quadrupole ion traps

NASA Astrophysics Data System (ADS)

Peng, Wen-Ping; Lee, Yuan T.; Ting, Joseph W.; Chang, Huan-Cheng

2005-02-01

A sine wave that controls a quadrupole ion trap is generated from a low voltage source, boosted to high voltage through a transformer. Since not even the best transformers can keep a flat amplitude response with respect to frequency, knowing the accurate peak-to-peak value of the sine wave is paramount when the frequency is varied. We have developed an averaging peak-to-peak voltage detector for such measurements and demonstrated that the device is an essential tool to make possible high-precision mass determination of single charged microparticles with masses greater than 1×1011u. Tests of the detector with sine waves from a FLUKE 5720A standard source in the neighborhood of 1400Vpp and frequencies ranging from 100to700Hz showed a measurement accuracy better than 10ppm. The detector settled within 5s after each reset to 5 digits of DVM rock-steady reading, and the calibration against the same source after 3weeks of continuous use of the circuit produced a mere overall 1ppm difference.

Combined dispersive/interference spectroscopy for producing a vector spectrum

DOEpatents

Erskine, David J.

2002-01-01

A method of measuring the spectral properties of broadband waves that combines interferometry with a wavelength disperser having many spectral channels to produce a fringing spectrum. Spectral mapping, Doppler shifts, metrology of angles, distances and secondary effects such as temperature, pressure, and acceleration which change an interferometer cavity length can be measured accurately by a compact instrument using broadband illumination. Broadband illumination avoids the fringe skip ambiguities of monochromatic waves. The interferometer provides arbitrarily high spectral resolution, simple instrument response, compactness, low cost, high field of view and high efficiency. The inclusion of a disperser increases fringe visibility and signal to noise ratio over an interferometer used alone for broadband waves. The fringing spectrum is represented as a wavelength dependent 2-d vector, which describes the fringe amplitude and phase. Vector mathematics such as generalized dot products rapidly computes average broadband phase shifts to high accuracy. A Moire effect between the interferometer's sinusoidal transmission and the illumination heterodynes high resolution spectral detail to low spectral detail, allowing the use of a low resolution disperser. Multiple parallel interferometer cavities of fixed delay allow the instantaneous mapping of a spectrum, with an instrument more compact for the same spectral resolution than a conventional dispersive spectrometer, and not requiring a scanning delay.

Survey of SRF guns

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belomestnykh, S.

Developing Superconducting RF (SRF) electron guns is an active field with several laboratories working on different gun designs. While the first guns were based on elliptic cavity geometries, Quarter Wave Resonator (QWR) option is gaining popularity. QWRs are especially well suited for producing beams with high charge per bunch. In this talk we will describe recent progress in developing both types of SRF guns. SRF guns made excellent progress in the last two years. Several guns generated beams and one, at HZDR, injected beam into an accelerator. By accomplishing this, HZDR/ELBE gun demonstrated feasibility of the SRF gun concept withmore » a normal-conducting Cs{sub 2}Te cathode. The cathode demonstrated very good performance with the lifetime of {approx}1 year. However, for high average current/high bunch charge operation CsK{sub 2}Sb is preferred as it needs green lasers, unlike UV laser for the Cs{sub 2}Te, which makes it easier to build laser/optics systems. Other high QE photocathodes are being developed for SRF guns, most notably diamond-amplified photocathode. Several QWR guns are under development with one producing beam already. They are very promising for high bunch charge operation. The field is very active and we should expect more good results soon.« less

Enhancing SMAP Soil Moisture Retrievals via Superresolution Techniques

NASA Astrophysics Data System (ADS)

Beale, K. D.; Ebtehaj, A. M.; Romberg, J. K.; Bras, R. L.

2017-12-01

Soil moisture is a key state variable that modulates land-atmosphere interactions and its high-resolution global scale estimates are essential for improved weather forecasting, drought prediction, crop management, and the safety of troop mobility. Currently, NASA's Soil Moisture Active/Passive (SMAP) satellite provides a global picture of soil moisture variability at a resolution of 36 km, which is prohibitive for some hydrologic applications. The goal of this research is to enhance the resolution of SMAP passive microwave retrievals by a factor of 2 to 4 using modern superresolution techniques that rely on the knowledge of high-resolution land surface models. In this work, we explore several super-resolution techniques including an empirical dictionary method, a learned dictionary method, and a three-layer convolutional neural network. Using a year of global high-resolution land surface model simulations as training set, we found that we are able to produce high-resolution soil moisture maps that outperform the original low-resolution observations both qualitatively and quantitatively. In particular, on a patch-by-patch basis we are able to produce estimates of high-resolution soil moisture maps that improve on the original low-resolution patches by on average 6% in terms of mean-squared error, and 14% in terms of the structural similarity index.

The writing retreat: a high-yield clinical faculty development opportunity in academic writing.

PubMed

Cable, Christian T; Boyer, Debra; Colbert, Colleen Y; Boyer, Edward W

2013-06-01

The need for consistent academic productivity challenges junior clinician-scholars, who often lack the aptitude to ensure efficient production of manuscripts. To solve this problem, an academic division of a major medical center developed an off-site writing retreat. The purpose of the retreat was not to teach writing skills, but to offer senior mentor assistance with a focus on the elements of manuscript writing. The retreat paired senior faculty members with junior staff. Senior faculty identified manuscript topics and provided real-time writing and editing supervision. Team-building exercises, midcourse corrections, and debriefing interviews were built into the retreat. The number of manuscripts and grant proposals generated during the 2008-2011 retreats was recorded, and the program was evaluated by using unstructured debriefing interviews. An average of 6 to 7 faculty members and fellows participated in each retreat. During the past 4 years, participants produced an average of 3 grant proposals and 7 manuscripts per retreat. After the writing retreat, each fellow and junior faculty member produced an average of 4 scholarly products per year, compared to fewer than 2 for prior years' retreats. Participant feedback indicated the success of the retreat resulted from protected time, direct mentorship by the scholars involved, and pairing of authors, which allows for rapid production of manuscripts and accelerated the editing process. More than 80% of mentors returned each year to participate. The writing retreat is a feasible, effective strategy to increase scholarship among faculty, acceptable to mentees and mentors, and sustainable over time.

Smoking portrayal in Ethiopian movies: a theory-based content analysis.

PubMed

Bekalu, Mesfin Awoke; Viswanath, K

2018-04-17

Considerable research from high-income countries has characterized the amount, nature and effects of movie smoking depiction. However, in low- and middle-income countries (LMICs) where tobacco use and tobacco-related diseases are growing, little research has investigated smoking imagery in movies. This study examined the extent and nature of smoking portrayal in locally produced Ethiopian movies, and estimated the number of tobacco impressions movies delivered. Sample movies were taken from YouTube. Keyword searches were conducted using 'Ethiopian movies' and 'Ethiopian drama' on 18 September 2016. In each search, the first 100 most viewed movies were examined. Excluding repeated results, a total of 123 movies were selected for content analysis. Three coders participated. Results indicated that 86 (69.9%, 95% CI 63-78%) of the 123 most viewed movies contain at least one tobacco incident (TI). The movies depict a total of 403 TIs, with an average of 4.7 (95% CI 3.7-5.6) TIs in each movie. The average length of TIs is 1 min and 11 s. On average, the movies were viewed more than half a million times by September 2016, and received more 'likes' than 'dislikes', z = -8.05, p = 0.00. They delivered over 194 million tobacco impressions via YouTube alone from July 2012 through September 2016. Most TIs portray smoking as a socially acceptable behavior with no negative health consequences. The findings suggest that as with transnational Western movies, locally produced movies in LMICs should be scrutinized for compliance with national and international regulatory efforts.

Lessons Learned from OMI Observations of Point Source SO2 Pollution

NASA Technical Reports Server (NTRS)

Krotkov, N.; Fioletov, V.; McLinden, Chris

2011-01-01

The Ozone Monitoring Instrument (OMI) on NASA Aura satellite makes global daily measurements of the total column of sulfur dioxide (SO2), a short-lived trace gas produced by fossil fuel combustion, smelting, and volcanoes. Although anthropogenic SO2 signals may not be detectable in a single OMI pixel, it is possible to see the source and determine its exact location by averaging a large number of individual measurements. We describe new techniques for spatial and temporal averaging that have been applied to the OMI SO2 data to determine the spatial distributions or "fingerprints" of SO2 burdens from top 100 pollution sources in North America. The technique requires averaging of several years of OMI daily measurements to observe SO2 pollution from typical anthropogenic sources. We found that the largest point sources of SO2 in the U.S. produce elevated SO2 values over a relatively small area - within 20-30 km radius. Therefore, one needs higher than OMI spatial resolution to monitor typical SO2 sources. TROPOMI instrument on the ESA Sentinel 5 precursor mission will have improved ground resolution (approximately 7 km at nadir), but is limited to once a day measurement. A pointable geostationary UVB spectrometer with variable spatial resolution and flexible sampling frequency could potentially achieve the goal of daily monitoring of SO2 point sources and resolve downwind plumes. This concept of taking the measurements at high frequency to enhance weak signals needs to be demonstrated with a GEOCAPE precursor mission before 2020, which will help formulating GEOCAPE measurement requirements.

Re-evaluation of forest biomass carbon stocks and lessons from the world's most carbon-dense forests.

PubMed

Keith, Heather; Mackey, Brendan G; Lindenmayer, David B

2009-07-14

From analysis of published global site biomass data (n = 136) from primary forests, we discovered (i) the world's highest known total biomass carbon density (living plus dead) of 1,867 tonnes carbon per ha (average value from 13 sites) occurs in Australian temperate moist Eucalyptus regnans forests, and (ii) average values of the global site biomass data were higher for sampled temperate moist forests (n = 44) than for sampled tropical (n = 36) and boreal (n = 52) forests (n is number of sites per forest biome). Spatially averaged Intergovernmental Panel on Climate Change biome default values are lower than our average site values for temperate moist forests, because the temperate biome contains a diversity of forest ecosystem types that support a range of mature carbon stocks or have a long land-use history with reduced carbon stocks. We describe a framework for identifying forests important for carbon storage based on the factors that account for high biomass carbon densities, including (i) relatively cool temperatures and moderately high precipitation producing rates of fast growth but slow decomposition, and (ii) older forests that are often multiaged and multilayered and have experienced minimal human disturbance. Our results are relevant to negotiations under the United Nations Framework Convention on Climate Change regarding forest conservation, management, and restoration. Conserving forests with large stocks of biomass from deforestation and degradation avoids significant carbon emissions to the atmosphere, irrespective of the source country, and should be among allowable mitigation activities. Similarly, management that allows restoration of a forest's carbon sequestration potential also should be recognized.

Re-evaluation of forest biomass carbon stocks and lessons from the world's most carbon-dense forests

PubMed Central

Keith, Heather; Mackey, Brendan G.; Lindenmayer, David B.

2009-01-01

From analysis of published global site biomass data (n = 136) from primary forests, we discovered (i) the world's highest known total biomass carbon density (living plus dead) of 1,867 tonnes carbon per ha (average value from 13 sites) occurs in Australian temperate moist Eucalyptus regnans forests, and (ii) average values of the global site biomass data were higher for sampled temperate moist forests (n = 44) than for sampled tropical (n = 36) and boreal (n = 52) forests (n is number of sites per forest biome). Spatially averaged Intergovernmental Panel on Climate Change biome default values are lower than our average site values for temperate moist forests, because the temperate biome contains a diversity of forest ecosystem types that support a range of mature carbon stocks or have a long land-use history with reduced carbon stocks. We describe a framework for identifying forests important for carbon storage based on the factors that account for high biomass carbon densities, including (i) relatively cool temperatures and moderately high precipitation producing rates of fast growth but slow decomposition, and (ii) older forests that are often multiaged and multilayered and have experienced minimal human disturbance. Our results are relevant to negotiations under the United Nations Framework Convention on Climate Change regarding forest conservation, management, and restoration. Conserving forests with large stocks of biomass from deforestation and degradation avoids significant carbon emissions to the atmosphere, irrespective of the source country, and should be among allowable mitigation activities. Similarly, management that allows restoration of a forest's carbon sequestration potential also should be recognized. PMID:19553199

The average receiver operating characteristic curve in multireader multicase imaging studies

PubMed Central

Samuelson, F W

2014-01-01

Objective: In multireader, multicase (MRMC) receiver operating characteristic (ROC) studies for evaluating medical imaging systems, the area under the ROC curve (AUC) is often used as a summary metric. Owing to the limitations of AUC, plotting the average ROC curve to accompany the rigorous statistical inference on AUC is recommended. The objective of this article is to investigate methods for generating the average ROC curve from ROC curves of individual readers. Methods: We present both a non-parametric method and a parametric method for averaging ROC curves that produce a ROC curve, the area under which is equal to the average AUC of individual readers (a property we call area preserving). We use hypothetical examples, simulated data and a real-world imaging data set to illustrate these methods and their properties. Results: We show that our proposed methods are area preserving. We also show that the method of averaging the ROC parameters, either the conventional bi-normal parameters (a, b) or the proper bi-normal parameters (c, da), is generally not area preserving and may produce a ROC curve that is intuitively not an average of multiple curves. Conclusion: Our proposed methods are useful for making plots of average ROC curves in MRMC studies as a companion to the rigorous statistical inference on the AUC end point. The software implementing these methods is freely available from the authors. Advances in knowledge: Methods for generating the average ROC curve in MRMC ROC studies are formally investigated. The area-preserving criterion we defined is useful to evaluate such methods. PMID:24884728

An Analysis of Efficiency in Senior Secondary Schools in the Gambia 2006-2008: Educational Inputs and Production of Credits in English and Mathematics Subjects

ERIC Educational Resources Information Center

Sillah, B. M. S.

2012-01-01

This paper employs a stochastic production frontier model to assess the efficiency of the senior secondary schools in the Gambia. It examines their efficiency in using and mixing the educational inputs of average teacher salary, average teacher education, average teacher experience and students-to-teacher ratio in producing the number of students…

Use of Homogeneously-Sized Carbon Steel Ball Bearings to Study Microbially-Influenced Corrosion in Oil Field Samples

PubMed Central

Voordouw, Gerrit; Menon, Priyesh; Pinnock, Tijan; Sharma, Mohita; Shen, Yin; Venturelli, Amanda; Voordouw, Johanna; Sexton, Aoife

2016-01-01

Microbially-influenced corrosion (MIC) contributes to the general corrosion rate (CR), which is typically measured with carbon steel coupons. Here we explore the use of carbon steel ball bearings, referred to as beads (55.0 ± 0.3 mg; Ø = 0.238 cm), for determining CRs. CRs for samples from an oil field in Oceania incubated with beads were determined by the weight loss method, using acid treatment to remove corrosion products. The release of ferrous and ferric iron was also measured and CRs based on weight loss and iron determination were in good agreement. Average CRs were 0.022 mm/yr for eight produced waters with high numbers (105/ml) of acid-producing bacteria (APB), but no sulfate-reducing bacteria (SRB). Average CRs were 0.009 mm/yr for five central processing facility (CPF) waters, which had no APB or SRB due to weekly biocide treatment and 0.036 mm/yr for 2 CPF tank bottom sludges, which had high numbers of APB (106/ml) and SRB (108/ml). Hence, corrosion monitoring with carbon steel beads indicated that biocide treatment of CPF waters decreased the CR, except where biocide did not penetrate. The CR for incubations with 20 ml of a produced water decreased from 0.061 to 0.007 mm/yr when increasing the number of beads from 1 to 40. CRs determined with beads were higher than those with coupons, possibly also due to a higher weight of iron per unit volume used in incubations with coupons. Use of 1 ml syringe columns, containing carbon steel beads, and injected with 10 ml/day of SRB-containing medium for 256 days gave a CR of 0.11 mm/yr under flow conditions. The standard deviation of the distribution of residual bead weights, a measure for the unevenness of the corrosion, increased with increasing CR. The most heavily corroded beads showed significant pitting. Hence the use of uniformly sized carbon steel beads offers new opportunities for screening and monitoring of corrosion including determination of the distribution of corrosion rates, which allows estimation of the probability of high rate events that may lead to failure. PMID:27047467

Fusion Blanket Coolant Section Criteria, Methodology, and Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeMuth, J. A.; Meier, W. R.; Jolodosky, A.

2015-10-02

The focus of this LDRD was to explore potential Li alloys that would meet the tritium breeding and blanket cooling requirements but with reduced chemical reactivity, while maintaining the other attractive features of pure Li breeder/coolant. In other fusion approaches (magnetic fusion energy or MFE), 17Li- 83Pb alloy is used leveraging Pb’s ability to maintain high TBR while lowering the levels of lithium in the system. Unfortunately this alloy has a number of potential draw-backs. Due to the high Pb content, this alloy suffers from very high average density, low tritium solubility, low system energy, and produces undesirable activation productsmore » in particular polonium. The criteria considered in the selection of a tritium breeding alloy are described in the following section.« less

Optical Amplifier Based Space Solar Power

NASA Technical Reports Server (NTRS)

Fork, Richard L.

2001-01-01

The objective was to design a safe optical power beaming system for use in space. Research was focused on identification of strategies and structures that would enable achievement near diffraction limited optical beam quality, highly efficient electrical to optical conversion, and high average power in combination in a single system. Efforts centered on producing high efficiency, low mass of the overall system, low operating temperature, precision pointing and tracking capability, compatibility with useful satellite orbits, component and system reliability, and long component and system life in space. A system based on increasing the power handled by each individual module to an optimum and the number of modules in the complete structure was planned. We were concerned with identifying the most economical and rapid path to commercially viable safe space solar power.

Turbulent dispersal promotes species coexistence

PubMed Central

Berkley, Heather A; Kendall, Bruce E; Mitarai, Satoshi; Siegel, David A

2010-01-01

Several recent advances in coexistence theory emphasize the importance of space and dispersal, but focus on average dispersal rates and require spatial heterogeneity, spatio-temporal variability or dispersal-competition tradeoffs to allow coexistence. We analyse a model with stochastic juvenile dispersal (driven by turbulent flow in the coastal ocean) and show that a low-productivity species can coexist with a high-productivity species by having dispersal patterns sufficiently uncorrelated from those of its competitor, even though, on average, dispersal statistics are identical and subsequent demography and competition is spatially homogeneous. This produces a spatial storage effect, with an ephemeral partitioning of a ‘spatial niche’, and is the first demonstration of a physical mechanism for a pure spatiotemporal environmental response. ‘Turbulent coexistence’ is widely applicable to marine species with pelagic larval dispersal and relatively sessile adult life stages (and perhaps some wind-dispersed species) and complements other spatial and temporal storage effects previously documented for such species. PMID:20455921

Emergence of a fluctuation relation for heat in nonequilibrium Landauer processes

NASA Astrophysics Data System (ADS)

Taranto, Philip; Modi, Kavan; Pollock, Felix A.

2018-05-01

In a generalized framework for the Landauer erasure protocol, we study bounds on the heat dissipated in typical nonequilibrium quantum processes. In contrast to thermodynamic processes, quantum fluctuations are not suppressed in the nonequilibrium regime and cannot be ignored, making such processes difficult to understand and treat. Here we derive an emergent fluctuation relation that virtually guarantees the average heat produced to be dissipated into the reservoir either when the system or reservoir is large (or both) or when the temperature is high. The implication of our result is that for nonequilibrium processes, heat fluctuations away from its average value are suppressed independently of the underlying dynamics exponentially quickly in the dimension of the larger subsystem and linearly in the inverse temperature. We achieve these results by generalizing a concentration of measure relation for subsystem states to the case where the global state is mixed.

Teleportation of a two-mode entangled coherent state encoded with two-qubit information

NASA Astrophysics Data System (ADS)

Mishra, Manoj K.; Prakash, Hari

2010-09-01

We propose a scheme to teleport a two-mode entangled coherent state encoded with two-qubit information, which is better than the two schemes recently proposed by Liao and Kuang (2007 J. Phys. B: At. Mol. Opt. Phys. 40 1183) and by Phien and Nguyen (2008 Phys. Lett. A 372 2825) in that our scheme gives higher value of minimum assured fidelity and minimum average fidelity without using any nonlinear interactions. For involved coherent states | ± αrang, minimum average fidelity in our case is >=0.99 for |α| >= 1.6 (i.e. |α|2 >= 2.6), while previously proposed schemes referred above report the same for |α| >= 5 (i.e. |α|2 >= 25). Since it is very challenging to produce superposed coherent states of high coherent amplitude (|α|), our teleportation scheme is at the reach of modern technology.

Summary statistics in auditory perception.

PubMed

McDermott, Josh H; Schemitsch, Michael; Simoncelli, Eero P

2013-04-01

Sensory signals are transduced at high resolution, but their structure must be stored in a more compact format. Here we provide evidence that the auditory system summarizes the temporal details of sounds using time-averaged statistics. We measured discrimination of 'sound textures' that were characterized by particular statistical properties, as normally result from the superposition of many acoustic features in auditory scenes. When listeners discriminated examples of different textures, performance improved with excerpt duration. In contrast, when listeners discriminated different examples of the same texture, performance declined with duration, a paradoxical result given that the information available for discrimination grows with duration. These results indicate that once these sounds are of moderate length, the brain's representation is limited to time-averaged statistics, which, for different examples of the same texture, converge to the same values with increasing duration. Such statistical representations produce good categorical discrimination, but limit the ability to discern temporal detail.

Improving Signal-to-Noise Ratio in Scanning Transmission Electron Microscopy Energy-Dispersive X-Ray (STEM-EDX) Spectrum Images Using Single-Atomic-Column Cross-Correlation Averaging.

PubMed

Jeong, Jong Seok; Mkhoyan, K Andre

2016-06-01

Acquiring an atomic-resolution compositional map of crystalline specimens has become routine practice, thus opening possibilities for extracting subatomic information from such maps. A key challenge for achieving subatomic precision is the improvement of signal-to-noise ratio (SNR) of compositional maps. Here, we report a simple and reliable solution for achieving high-SNR energy-dispersive X-ray (EDX) spectroscopy spectrum images for individual atomic columns. The method is based on standard cross-correlation aided by averaging of single-column EDX maps with modifications in the reference image. It produces EDX maps with minimal specimen drift, beam drift, and scan distortions. Step-by-step procedures to determine a self-consistent reference map with a discussion on the reliability, stability, and limitations of the method are presented here.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seiple, Timothy E.; Coleman, André M.; Skaggs, Richard L.

Within the United States and Puerto Rico, publicly owned treatment works (POTWs) process 130.5 Gl/d (34.5 Bgal/d) of wastewater, producing sludge as a waste product. Emerging technologies offer novel waste-to-energy pathways through whole sludge conversion into biofuels. Assessing the feasibility, scalability and tradeoffs of various energy conversion pathways is difficult in the absence of highly spatially resolved estimates of sludge production. In this study, average wastewater solids concentrations and removal rates, and site specific daily average influent flow are used to estimate site specific annual sludge production on a dry weight basis for >15,000 POTWs. Current beneficial uses, regional productionmore » hotspots and feedstock aggregation potential are also assessed. Analyses indicate 1) POTWs capture 12.56 Tg/y (13.84 MT/y) of dry solids; 2) 50% are not beneficially utilized, and 3) POTWs can support seven regions that aggregate >910 Mg/d (1000 T/d) of sludge within a travel distance of 100 km.« less

LINEAR COUNT-RATE METER

DOEpatents

Henry, J.J.

1961-09-01

A linear count-rate meter is designed to provide a highly linear output while receiving counting rates from one cycle per second to 100,000 cycles per second. Input pulses enter a linear discriminator and then are fed to a trigger circuit which produces positive pulses of uniform width and amplitude. The trigger circuit is connected to a one-shot multivibrator. The multivibrator output pulses have a selected width. Feedback means are provided for preventing transistor saturation in the multivibrator which improves the rise and decay times of the output pulses. The multivibrator is connected to a diode-switched, constant current metering circuit. A selected constant current is switched to an averaging circuit for each pulse received, and for a time determined by the received pulse width. The average output meter current is proportional to the product of the counting rate, the constant current, and the multivibrator output pulse width.

Effect of statins on skeletal muscle function.

PubMed

Parker, Beth A; Capizzi, Jeffrey A; Grimaldi, Adam S; Clarkson, Priscilla M; Cole, Stephanie M; Keadle, Justin; Chipkin, Stuart; Pescatello, Linda S; Simpson, Kathleen; White, C Michael; Thompson, Paul D

2013-01-01

Many clinicians believe that statins cause muscle pain, but this has not been observed in clinical trials, and the effect of statins on muscle performance has not been carefully studied. The Effect of Statins on Skeletal Muscle Function and Performance (STOMP) study assessed symptoms and measured creatine kinase, exercise capacity, and muscle strength before and after atorvastatin 80 mg or placebo was administered for 6 months to 420 healthy, statin-naive subjects. No individual creatine kinase value exceeded 10 times normal, but average creatine kinase increased 20.8±141.1 U/L (P<0.0001) with atorvastatin. There were no significant changes in several measures of muscle strength or exercise capacity with atorvastatin, but more atorvastatin than placebo subjects developed myalgia (19 versus 10; P=0.05). Myalgic subjects on atorvastatin or placebo had decreased muscle strength in 5 of 14 and 4 of 14 variables, respectively (P=0.69). These results indicate that high-dose atorvastatin for 6 months does not decrease average muscle strength or exercise performance in healthy, previously untreated subjects. Nevertheless, this blinded, controlled trial confirms the undocumented impression that statins increase muscle complaints. Atorvastatin also increased average creatine kinase, suggesting that statins produce mild muscle injury even among asymptomatic subjects. This increase in creatine kinase should prompt studies examining the effects of more prolonged, high-dose statin treatment on muscular performance. URL: http://www.clinicaltrials.gov. Unique identifier: NCT00609063.

Jupiter Analogs Orbit Stars with an Average Metallicity Close to That of the Sun

NASA Astrophysics Data System (ADS)

Buchhave, Lars A.; Bitsch, Bertram; Johansen, Anders; Latham, David W.; Bizzarro, Martin; Bieryla, Allyson; Kipping, David M.

2018-03-01

Jupiter played an important role in determining the structure and configuration of the Solar System. Whereas hot-Jupiter type exoplanets preferentially form around metal-rich stars, the conditions required for the formation of planets with masses, orbits, and eccentricities comparable to Jupiter (Jupiter analogs) are unknown. Using spectroscopic metallicities, we show that stars hosting Jupiter analogs have an average metallicity close to solar, in contrast to their hot-Jupiter and eccentric cool-Jupiter counterparts, which orbit stars with super-solar metallicities. Furthermore, the eccentricities of Jupiter analogs increase with host-star metallicity, suggesting that planet–planet scatterings producing highly eccentric cool Jupiters could be more common in metal-rich environments. To investigate a possible explanation for these metallicity trends, we compare the observations to numerical simulations, which indicate that metal-rich stars typically form multiple Jupiters, leading to planet–planet interactions and, hence, a prevalence of either eccentric cool Jupiters or hot Jupiters with circularized orbits. Although the samples are small and exhibit variations in their metallicities, suggesting that numerous processes other than metallicity affect the formation of planetary systems, the data in hand suggests that Jupiter analogs and terrestrial-sized planets form around stars with average metallicities close to solar, whereas high-metallicity systems preferentially host eccentric cool Jupiter or hot Jupiters, indicating that higher metallicity systems may not be favorable for the formation of planetary systems akin to the Solar System.

High frequency source localization in a shallow ocean sound channel using frequency difference matched field processing.

PubMed

Worthmann, Brian M; Song, H C; Dowling, David R

2015-12-01

Matched field processing (MFP) is an established technique for source localization in known multipath acoustic environments. Unfortunately, in many situations, particularly those involving high frequency signals, imperfect knowledge of the actual propagation environment prevents accurate propagation modeling and source localization via MFP fails. For beamforming applications, this actual-to-model mismatch problem was mitigated through a frequency downshift, made possible by a nonlinear array-signal-processing technique called frequency difference beamforming [Abadi, Song, and Dowling (2012). J. Acoust. Soc. Am. 132, 3018-3029]. Here, this technique is extended to conventional (Bartlett) MFP using simulations and measurements from the 2011 Kauai Acoustic Communications MURI experiment (KAM11) to produce ambiguity surfaces at frequencies well below the signal bandwidth where the detrimental effects of mismatch are reduced. Both the simulation and experimental results suggest that frequency difference MFP can be more robust against environmental mismatch than conventional MFP. In particular, signals of frequency 11.2 kHz-32.8 kHz were broadcast 3 km through a 106-m-deep shallow ocean sound channel to a sparse 16-element vertical receiving array. Frequency difference MFP unambiguously localized the source in several experimental data sets with average peak-to-side-lobe ratio of 0.9 dB, average absolute-value range error of 170 m, and average absolute-value depth error of 10 m.

A Comparison of Two Methods for Initiating Air Mass Back Trajectories

NASA Astrophysics Data System (ADS)

Putman, A.; Posmentier, E. S.; Faiia, A. M.; Sonder, L. J.; Feng, X.

2014-12-01

Lagrangian air mass tracking programs in back cast mode are a powerful tool for estimating the water vapor source of precipitation events. The altitudes above the precipitation site where particle's back trajectories begin influences the source estimation. We assume that precipitation comes from water vapor in condensing regions of the air column, so particles are placed in proportion to an estimated condensation profile. We compare two methods for estimating where condensation occurs and the resulting evaporation sites for 63 events at Barrow, AK. The first method (M1) uses measurements from a 35 GHz vertically resolved cloud radar (MMCR), and algorithms developed by Zhao and Garrett1 to calculate precipitation rate. The second method (M2) uses the Global Data Assimilation System reanalysis data in a lofting model. We assess how accurately M2, developed for global coverage, will perform in absence of direct cloud observations. Results from the two methods are statistically similar. The mean particle height estimated by M2 is, on average, 695 m (s.d. = 1800 m) higher than M1. The corresponding average vapor source estimated by M2 is 1.5⁰ (s.d. = 5.4⁰) south of M1. In addition, vapor sources for M2 relative to M1 have ocean surface temperatures averaging 1.1⁰C (s.d. = 3.5⁰C) warmer, and reported ocean surface relative humidities 0.31% (s.d. = 6.1%) drier. All biases except the latter are statistically significant (p = 0.02 for each). Results were skewed by events where M2 estimated very high altitudes of condensation. When M2 produced an average particle height less than 5000 m (89% of events), M2 estimated mean particle heights 76 m (s.d. = 741 m) higher than M1, corresponding to a vapor source 0.54⁰ (s.d. = 4.2⁰) south of M1. The ocean surface at the vapor source was an average of 0.35⁰C (s.d. = 2.35⁰C) warmer and ocean surface relative humidities were 0.02% (s.d. = 5.5%) wetter. None of the biases was statistically significant. If the vapor source meteorology estimated by M2 is used to determine vapor isotopic properties it would produce results similar to M1 in all cases except the occasional very high cloud. The methods strive to balance a sufficient number of tracked air masses for meaningful vapor source estimation with minimal computational time. Zhao, C and Garrett, T.J. 2008, J. Geophys. Res.

7 CFR 1580.102 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... of the United States. Marketing year means the marketing season or year as defined by National... Administrator. National average price means the average price paid to producers for an agricultural commodity in a marketing year as determined by the Administrator. Net farm income means net farm profit or loss...

Enzymatic modification of a model homogalacturonan with the thermally tolerant pectin methylesterase from Citrus: 1. Nanostructural characterization, enzyme mode of action, and effect of pH.

PubMed

Cameron, Randall G; Luzio, Gary A; Vasu, Prasanna; Savary, Brett J; Williams, Martin A K

2011-03-23

Methyl ester distribution in pectin homogalacturonan has a major influence on functionality. Enzymatic engineering of the pectin nanostructure for tailoring functionality can expand the role of pectin as a food-formulating agent and the use of in situ modification in prepared foods. We report on the mode of action of a unique citrus thermally tolerant pectin methylesterase (TT-PME) and the nanostructural modifications that it produces. The enzyme was used to produce a controlled demethylesterification series from a model homogalacturonan. Oligogalacturonides released from the resulting demethylesterified blocks introduced by TT-PME using a limited endopolygalacturonase digestion were separated and quantified by high-pressure anion-exchange chromatography (HPAEC) coupled to an evaporative light-scattering detector (ELSD). The results were consistent with the predictions of a numerical simulation, which assumed a multiple-attack mechanism and a degree of processivity ∼10, at both pH 4.5 and 7.5. The average demethylesterified block size (0.6-2.8 nm) and number of average-sized blocks per molecule (0.8-1.9) differed, depending upon pH of the enzyme treatment. The mode of action of this enzyme and consequent nanostructural modifications of pectin differ from a previously characterized citrus salt-independent pectin methylesterase (SI-PME).

Rootless shield and perched lava pond collapses at Kīlauea Volcano, Hawai'i

USGS Publications Warehouse

Patrick, Matthew R.; Orr, Tim R.

2012-01-01

Effusion rate is a primary measurement used to judge the expected advance rate, length, and hazard potential of lava flows. At basaltic volcanoes, the rapid draining of lava stored in rootless shields and perched ponds can produce lava flows with much higher local effusion rates and advance velocities than would be expected based on the effusion rate at the vent. For several months in 2007–2008, lava stored in a series of perched ponds and rootless shields on Kīlauea Volcano, Hawai'i, was released episodically to produce fast-moving 'a'ā lava flows. Several of these lava flows approached Royal Gardens subdivision and threatened the safety of remaining residents. Using time-lapse image measurements, we show that the initial time-averaged discharge rate for one collapse-triggered lava flow was approximately eight times greater than the effusion rate at the vent. Though short-lived, the collapse-triggered 'a'ā lava flows had average advance rates approximately 45 times greater than that of the pāhoehoe flow field from which they were sourced. The high advance rates of the collapse-triggered lava flows demonstrates that recognition of lava accumulating in ponds and shields, which may be stored in a cryptic manner, is vital for accurately assessing short-term hazards at basaltic volcanoes.

Nutritive quality and protein production from grain legumes in a boreal climate.

PubMed

Lizarazo, Clara I; Lampi, Anna-Maija; Liu, Jingwei; Sontag-Strohm, Tuula; Piironen, Vieno; Stoddard, Frederick L

2015-08-15

Boreal cropping systems are heavily focused on the production of small-grain cereals; to improve their resilience to climate change and to achieve food and feed security, diversification is needed. This study investigated the potential of faba bean, narrow-leafed lupin and lentil as protein crops in southern Finland, where faba bean is traditional but the other two are novel. Early cultivars of narrow-leafed lupin and lentil matured adequately. Protein concentration in faba bean was, at 32%, higher than the world average of 29%, while those of narrow-leafed lupin and lentil were close to their world averages. Protein yields decreased in the order faba bean > narrow-leafed lupin > lentil. Lipid content of faba bean and lentil was about 1.2% and that of narrow-leafed lupin about 5.5%, and fatty acid composition was largely oleic and linoleic in all three species. Both lentil and narrow-leafed lupin can be added to the range of feed and food crops produced at high latitudes in Europe. While faba bean produces the greatest protein yield and lysine concentration, the higher sulfur amino acid concentration in lupin, its oil content and its adaptation to acid, sandy soils not suitable for faba bean make it an attractive alternative. © 2014 Society of Chemical Industry.

Variability in Light-Duty Gasoline Vehicle Emission Factors from Trip-Based Real-World Measurements.

PubMed

Liu, Bin; Frey, H Christopher

2015-10-20

Using data obtained with portable emissions measurements systems (PEMS) on multiple routes for 100 gasoline vehicles, including passenger cars (PCs), passenger trucks (PTs), and hybrid electric vehicles (HEVs), variability in tailpipe emission rates was evaluated. Tier 2 emission standards are shown to be effective in lowering NOx, CO, and HC emission rates. Although PTs are larger, heavier vehicles that consume more fuel and produce more CO2 emissions, they do not necessarily produce more emissions of regulated pollutants compared to PCs. HEVs have very low emission rates compared to tier 2 vehicles under real-world driving. Emission factors vary with cycle average speed and road type, reflecting the combined impact of traffic control and traffic congestion. Compared to the slowest average speed and most congested cycles, optimal emission rates could be 50% lower for CO2, as much as 70% lower for NOx, 40% lower for CO, and 50% lower for HC. There is very high correlation among vehicles when comparing driving cycles. This has implications for how many cycles are needed to conduct comparisons between vehicles, such as when comparing fuels or technologies. Concordance between empirical and predicted emission rates using the U.S. Environmental Protection Agency's MOVES model was also assessed.

Transcranial measurements of the acoustic field produced by a low frequency focused ultrasound system

NASA Astrophysics Data System (ADS)

Voie, Arne; Fisher, David; Ahadi, Golnaz; Hölscher, Thilo

2012-11-01

The purpose of this study was to ascertain the effects of the skull on the location, shape and power of the acoustic field produced by a 150 mm radius hemispherical array operating at 220 kHz. We wanted to determine whether phase aberrations were significant at this frequency, the amount of attenuation, and whether CT data could be predictive of the trans-skull field. The effects of five calvaria were evaluated. Acoustic field data and CT scans for each skull specimen were imported into MATLAB® for measurements and visualization in two and three dimensions. We examined the effects of skull density, porosity, thickness, and sonication incident angles, and estimated the relative contributions of longitudinal and shear transmission to the total transmitted power. Power transmission through the skulls varied between 4% and 23% (mean: 12%). The range of focal position shifts was from 0.50 mm to 4.32 mm (mean: 1.95 mm). The 3 dB dimensions of the focused ultrasound (FUS) intensity focal volume increased on average by 39% (low: 4%, high: 122%). The 6 dB pressure focal volume increased by an average of 130 ± 75%. In general, the main effects of the skulls were power reduction, field dispersion and slight shift of focal peak location.

Space-Weathering on Mercury: Inferences Based on Comparison of MESSENGER Spectral Data and Experimental Space Weathering Data

NASA Astrophysics Data System (ADS)

Gillis-Davis, J. J.; Blewett, D. T.; Lawrence, D. J.; Izenberg, N. R.; McClintock, W. E.; Holsclaw, G. M.; Domingue, D. L.

2009-12-01

Production and accumulation of submicroscopic metallic iron (SMFe) is a principal mechanism by which surfaces of airless silicate bodies in the Solar System, exposed to the space weathering environment, experience spectral modification. Micrometeorite impact vaporization and solar-wind sputtering produce coatings of vapor-deposited SMFe. Both processes can be more intense on Mercury and, as a result, more efficient at creating melt and vapor. In addition, Ostwald ripening may cause SMFe particles to grow larger due to the high surface temperatures on Mercury (as great as 450°C). Spectral effects on the ultraviolet-visible-near-infrared continuum change with the amount and size of SMFe present. Thus, the physical properties and abundance of iron in Mercury’s regolith can be understood by comparing spectral data from controlled space-weathering experiments with spectra from MESSENGER’s Mercury Atmospheric and Surface Composition Spectrometer (MASCS). Knowledge of SMFe size and abundance may provide information on the space weathering conditions under which it was produced or subsequently modified. Reflectance spectra of laboratory-produced samples with varying SMFe grain sizes (average grain sizes of 8, 15, 35, and 40 nm) and iron compositions (from 0.005 to 3.8 wt% Fe as SMFe) are compared with MASCS disk-integrated reflectance from the first flyby of Mercury and will be compared with observations of spectral end members targeted for the third flyby. We compare spectra from 300 nm to 1400 nm wavelength, scaled to 1 at 700 nm, from the laboratory and MASCS. This comparison between laboratory and remote-sensing spectra reveals an excellent match with observations of Mercury for samples with an average iron metal grain size of 8 nm and 1.65 wt% FeO and 15 nm and 0.13 wt% Fe. These average grain sizes of the SMFe component are larger than the average grain size determined for lunar soil samples using transmission electron microscopy (3 nm in rims and 10-15 nm in agglutinates) but are smaller than values obtained from lunar spectra with the methods used here (15-25 nm). We can also infer that silicates in Mercury's high reflectance plains are potentially iron poor, precluding thick vapor deposits coating - both spectral data sets lack a 1-μm absorption and the experimental iron particles are suspended in an iron-free silica gel. Thus, our conclusion on the basis of spectral comparison is that SMFe on Mercury is potentially smaller than on the Moon and that Ostwald ripening is not a major influence on the surface of Mercury. The absence of pronounced darkening of the equatorial regions of Mercury in images from Mariner 10 and MESSENGER's Mercury Dual Imaging System supports also suggest an apparent lack of Ostwald ripening.

High-efficiency (6 + 1) × 1 pump-signal combiner based on low-deformation and high-precision alignment fabrication

NASA Astrophysics Data System (ADS)

Zou, Shuzhen; Chen, Han; Yu, Haijuan; Sun, Jing; Zhao, Pengfei; Lin, Xuechun

2017-12-01

We demonstrate a new method for fabricating a (6 + 1) × 1 pump-signal combiner based on the reduction of signal fiber diameter by corrosion. This method avoids the mismatch loss of the splice between the signal fiber and the output fiber caused by the signal fiber taper processing. The optimum radius of the corroded signal fiber was calculated according to the analysis of the influence of the cladding thickness on the laser propagating in the fiber core. Besides, we also developed a two-step splicing method to complete the high-precision alignment between the signal fiber core and the output fiber core. A high-efficiency (6 + 1) × 1 pump-signal combiner was produced with an average pump power transmission efficiency of 98.0% and a signal power transmission efficiency of 97.7%, which is well suitable for application to high-power fiber laser system.

Interferometric analysis of laboratory photoionized plasmas utilizing supersonic gas jet targets.

NASA Astrophysics Data System (ADS)

Swanson, Kyle James; Ivanov, Vladimir; Mancini, Roberto; Mayes, Daniel C.

2018-06-01

Photoionized plasmas are an important component of active galactic nuclei, x-ray binary systems and other astrophysical objects. Laboratory produced photoionized plasmas have mainly been studied at large scale facilities, due to the need for high intensity broadband x-ray flux. Using supersonic gas jets as targets has allowed university scale pulsed power generators to begin similar research. The two main advantages of this approach with supersonic gas jets include: possibility of a closer location to the x-ray source and no attenuation related to material used for containment and or tamping. Due to these factors, this experimental platform creates a laboratory environment that more closely resembles astrophysical environments. This system was developed at the Nevada Terawatt Facility using the 1 MA pulsed power generator Zebra. Neon, argon, and nitrogen supersonic gas jets are produced approximately 7-8mm from the z-pinch axis. The high intensity broadband x-ray flux produced by the collapse of the z-pinch wire array implosion irradiates the gas jet. Cylindrical wire arrays are made with 4 and 8 gold 10µm thick wire. The z-pinch radiates approximately 12-16kj of x-ray energy, with x-ray photons under 1Kev in energy. The photoionized plasma is measured via x-ray absorption spectroscopy and interferometry. A Mach-Zehnder interferometer is used to the measure neutral density of the jet prior to the zebra shot at a wavelength of 266 nm. A dual channel air-wedge shearing interferometer is used to measure electron density of the ionized gas jet during the shot, at wavelengths of 532nm and 266nm. Using a newly developed interferometric analysis tool, average ionization state maps of the plasma can be calculated. Interferometry for nitrogen and argon show an average ionization state in the range of 3-8. Preliminary x-ray absorption spectroscopy collected show neon absorption lines. This work was sponsored in part by DOE Office of Science Grant DE-SC0014451.

POISON SPIDER FIELD CHEMICAL FLOOD PROJECT, WYOMING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Douglas Arnell; Malcolm Pitts; Jie Qi

2004-11-01

A reservoir engineering and geologic study concluded that approximate 7,852,000 bbls of target oil exits in Poison Spider. Field pore volume, OOIP, and initial oil saturation are defined. Potential injection water has a total dissolved solids content of 1,275 mg/L with no measurable divalent cations. If the Lakota water consistently has no measurable cations, the injection water does not require softening to dissolve alkali. Produced water total dissolved solids were 2,835 mg/L and less than 20 mg/L hardness as the sum of divalent cations. Produced water requires softening to dissolve chemicals. Softened produced water was used to dissolve chemicals inmore » these evaluations. Crude oil API gravity varies across the field from 19.7 to 22.2 degrees with a dead oil viscosity of 95 to 280 cp at 75 F. Interfacial tension reductions of up to 21,025 fold (0.001 dyne/cm) were developed with fifteen alkaline-surfactant combinations at some alkali concentration. An additional three alkaline-surfactant combinations reduced the interfacial tension greater than 5,000 fold. NaOH generally produced the lowest interfacial tension values. Interfacial tension values of less than 0.021 dyne/cm were maintained when the solutions were diluted with produced water to about 60%. Na{sub 2}CO{sub 3} when mixed with surfactants did not reduce interfacial tension values to levels at which incremental oil can be expected. NaOH without surfactant interfacial tension reduction is at a level where some additional oil might be recovered. Most of the alkaline-surfactant-polymer solutions producing ultra low interfacial tension gave type II- phase behavior. Only two solutions produced type III phase behavior. Produced water dilution resulted in maintenance of phase type for a number of solutions at produced water dilutions exceeding 80% dilution. The average loss of phase type occurred at 80% dilution. Linear corefloods were performed to determine relative permeability end points, chemical-rock compatibility, polymer injectivity, dynamic chemical retention by rock, and recommended injected polymer concentration. Average initial oil saturation was 0.796 Vp. Produced water injection recovered 53% OOIP leaving an average residual oil saturation of 0.375 Vp. Poison Spider rock was strongly water-wet with a mobility ratio for produced water displacing the 280 cp crude oil of 8.6. Core was not sensitive to either alkali or surfactant injection. Injectivity increased 60 to 80% with alkali plus surfactant injection. Low and medium molecular weight polyacrylamide polymers (Flopaam 3330S and Flopaam 3430S) dissolved in either an alkaline-surfactant solution or softened produced water injected and flowed through Poison Spider rock. Recommended injected polyacrylamide concentration is 2,100 mg/L for both polymers for a unit mobility ratio. Radial corefloods were performed to evaluate oil recovery efficiency of different chemical solutions. Waterflood oil recovery averaged 46.4 OOIP and alkaline-surfactant-polymer flood oil recovery averaged an additional 18.1% OIP for a total of 64.6% OOIP. Oil cut change due to injection of a 1.5 wt% Na{sub 2}CO{sub 3} plus 0.05 wt% Petrostep B-100 plus 0.05 wt% Stepantan AS1216 plus 2100 mg/L Flopaam 3430S was from 2% to a peak of 23.5%. Additional study might determine the impact on oil recovery of a lower polymer concentration. An alkaline-surfactant-polymer flood field implementation outline report was written.« less

Ensuring Resiliency of the Milk and Dairy Industry in California

DTIC Science & Technology

2011-12-01

cannot be zero. Also, the upper bound cannot exceed the capacity of raw milk that the milk producing cows can make in each county. Between the...the amount of milk producing cows in each county and multiplying by the daily average amount of raw milk produced. RawMilkProd = NumMilkProdCows...the total number of milk producing cows . 365 TotalMilkProdDailyAvgAmtMilkProdPerCow TotalMilkProdCows = × We get the number of milk producing cows

Wind Generator & Biomass No-draft Gasification Hybrid

NASA Astrophysics Data System (ADS)

Hein, Matthew R.

The premise of this research is that underutilized but vast intermittent renewable energy resources, such as wind, can become more market competitive by coupling with storable renewable energy sources, like biomass; thereby creating a firm capacity resource. Specifically, the Midwest state of South Dakota has immense wind energy potential that is not used because of economic and logistic barriers of electrical transmission or storage. Coupling the state's intermittent wind resource with another of the state's energy resources, cellulosic non-food biomass, by using a wind generator and no-draft biomass gasification hybrid system will result in a energy source that is both firm and storable. The average energy content of common biomass feedstock was determined, 14.8 MJ/kg (7.153 Btu/lb), along with the assumed typical biomass conversion efficiency of the no-draft gasifier, 65%, so that an average electrical energy round trip efficiency (RTE) of 214% can be expected (i.e. One unit of wind electrical energy can produce 2.14 kWh of electrical energy stored as syngas.) from a wind generator and no-draft biomass gasification system. Wind characteristics are site specific so this analysis utilizes a synthetic wind resource to represent a statistically sound gross representation of South Dakota's wind regime based on data from the Wind Resource Assessment Network (WRAN) locations. A synthetic wind turbine generated from common wind turbine power curves and scaled to 1-MW rated capacity was utilized for this analysis in order to remove equipment bias from the results. A standard 8,760-hour BIN Analysis model was constructed within HOMER, powerful simulation software developed by the National Renewable Energy Laboratory (NREL) to model the performance of renewable power systems. It was found that the optimum configuration on a per-megawatt-transmitted basis required a wind generator (wind farm) rated capacity of 3-MW with an anticipated annual biomass feedstock of 26,132 GJ or an anticipated 1,766 tonnes of biomass. The levelized cost of electricity (COE) ranged from 65.6/GJ (236/MWh) to 208.9/GJ (752/MWh) with the price of generated electricity being most sensitive to the biomass feedstock cost and the levelized COE being significantly impacted by the high cost of compressed storage. The resulting electrical energy available to the grid has an approximate wholesale value of 13.5/GJ (48.6/MWh) based on year 2007 Midwest Reliability Organization (MRO) regional averages [1]. Therefore, the annual average wholesale value of the generated electricity is lower than the cost to produce the electricity. A significant deficiency of this simple comparison is that it does not consider the fact that the proposed wind and biomass gasification hybrid is now a dispatchable source of electricity with a near net-zero lifetime carbon footprint and storage capability. Dispatchable power can profit from market fluctuations that dramatically increase the value of available electricity so that in addition to providing base power the hybrid facility can store energy during low price points in the market and generate at full capacity during points of high prices. Any financial incentive for energy generated from reduced carbon technologies will also increase the value of electricity produced. Also, alternative operational parameters that do not require the costly storage of synthetic natural gas (SNG) will likely result in a more competitive levelized COE. Additional benefits of the system are in the flexibility of transporting wind and biomass energy produced as well as the end use of the energy. Instead of high-voltage electrical transmission a gas line can now be used to transport energy produced by the wind. Syngas can also be further processed into higher energy density liquefied syngas. Liquid fuels can then be transported via commercial freight on existing road infrastructure.

Transverse polarization of Λ and Λ produced inclusively in eN scattering at HERMES

DOE PAGES

Grebenyuk, O.

2002-11-01

The transverse polarization of inclusively produced Λ and Λ -hyperons has been studied at HERMES using the 27.6 GeV positron beam of HERA and an internal gas target. From the data taken in the years 1996-2000, 386,000 Λ and 72,000 Λ events have been reconstructed, allowing the measurement of the Λ and Λ polarizations with high statistical accuracy. Averaged over the full kinematic range of the data, the transverse polarizations were measured to be P n Λ = 5.4 ± 0.5 (stat) ± 1.5 (syst) % and P n Λ = -4.0 ± 1.3 (stat) ± 1.2 (syst) %. Themore » dependence of the polarization on several transverse momentum PT and on the hyperons' light cone momentum fraction ζ has been investigated.« less

Broadly tunable femtosecond mode-locking in a Tm:KYW laser near 2 μm.

PubMed

Lagatsky, A A; Calvez, S; Gupta, J A; Kisel, V E; Kuleshov, N V; Brown, C T A; Dawson, M D; Sibbett, W

2011-05-09

Efficient mode-locking in a Tm:KY(WO(4))(2) laser is demonstrated by using InGaAsSb quantum-well SESAMs. Self-starting ultrashort pulse generation was realized in the 1979-2074 nm spectral region. Maximum average output power up to 411 mW was produced around 1986 nm with the corresponding pulse duration and repetition rate of 549 fs and 105 MHz respectively. Optimised pulse durations of 386 fs were produced with an average power of 235 mW at 2029 nm. © 2011 Optical Society of America

High-throughput SNP genotyping of historical and modern samples of five bird species via sequence capture of ultraconserved elements.

PubMed

Lim, Haw Chuan; Braun, Michael J

2016-09-01

Sample availability limits population genetics research on many species, especially taxa from regions with high diversity. However, many such species are well represented in museum collections assembled before the molecular era. Development of techniques to recover genetic data from these invaluable specimens will benefit biodiversity science. Using a mixture of freshly preserved and historical tissue samples, and a sequence capture probe set targeting >5000 loci, we produced high-confidence genotype calls on thousands of single nucleotide polymorphisms (SNPs) in each of five South-East Asian bird species and their close relatives (N = 27-43). On average, 66.2% of the reads mapped to the pseudo-reference genome of each species. Of these mapped reads, an average of 52.7% was identified as PCR or optical duplicates. We achieved deeper effective sequencing for historical samples (122.7×) compared to modern samples (23.5×). The number of nucleotide sites with at least 8× sequencing depth was high, with averages ranging from 0.89 × 10(6)  bp (Arachnothera, modern samples) to 1.98 × 10(6)  bp (Stachyris, modern samples). Linear regression revealed that the amount of sequence data obtained from each historical sample (represented by per cent of the pseudo-reference genome recovered with ≥8× sequencing depth) was positively and significantly (P ≤ 0.013) related to how recently the sample was collected. We observed characteristic post-mortem damage in the DNA of historical samples. However, we were able to reduce the error rate significantly by truncating ends of reads during read mapping (local alignment) and conducting stringent SNP and genotype filtering. © 2016 John Wiley & Sons Ltd.

Ex vivo optimisation of a heterogeneous speed of sound model of the human skull for non-invasive transcranial focused ultrasound at 1 MHz.

PubMed

Marsac, L; Chauvet, D; La Greca, R; Boch, A-L; Chaumoitre, K; Tanter, M; Aubry, J-F

2017-09-01

Transcranial brain therapy has recently emerged as a non-invasive strategy for the treatment of various neurological diseases, such as essential tremor or neurogenic pain. However, treatments require millimetre-scale accuracy. The use of high frequencies (typically ≥1 MHz) decreases the ultrasonic wavelength to the millimetre scale, thereby increasing the clinical accuracy and lowering the probability of cavitation, which improves the safety of the technique compared with the use of low-frequency devices that operate at 220 kHz. Nevertheless, the skull produces greater distortions of high-frequency waves relative to low-frequency waves. High-frequency waves require high-performance adaptive focusing techniques, based on modelling the wave propagation through the skull. This study sought to optimise the acoustical modelling of the skull based on computed tomography (CT) for a 1 MHz clinical brain therapy system. The best model tested in this article corresponded to a maximum speed of sound of 4000 m.s -1 in the skull bone, and it restored 86% of the optimal pressure amplitude on average in a collection of six human skulls. Compared with uncorrected focusing, the optimised non-invasive correction led to an average increase of 99% in the maximum pressure amplitude around the target and an average decrease of 48% in the distance between the peak pressure and the selected target. The attenuation through the skulls was also assessed within the bandwidth of the transducers, and it was found to vary in the range of 10 ± 3 dB at 800 kHz and 16 ± 3 dB at 1.3 MHz.

TU-AB-BRA-02: An Efficient Atlas-Based Synthetic CT Generation Method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han, X

2016-06-15

Purpose: A major obstacle for MR-only radiotherapy is the need to generate an accurate synthetic CT (sCT) from MR image(s) of a patient for the purposes of dose calculation and DRR generation. We propose here an accurate and efficient atlas-based sCT generation method, which has a computation speed largely independent of the number of atlases used. Methods: Atlas-based sCT generation requires a set of atlases with co-registered CT and MR images. Unlike existing methods that align each atlas to the new patient independently, we first create an average atlas and pre-align every atlas to the average atlas space. When amore » new patient arrives, we compute only one deformable image registration to align the patient MR image to the average atlas, which indirectly aligns the patient to all pre-aligned atlases. A patch-based non-local weighted fusion is performed in the average atlas space to generate the sCT for the patient, which is then warped back to the original patient space. We further adapt a PatchMatch algorithm that can quickly find top matches between patches of the patient image and all atlas images, which makes the patch fusion step also independent of the number of atlases used. Results: Nineteen brain tumour patients with both CT and T1-weighted MR images are used as testing data and a leave-one-out validation is performed. Each sCT generated is compared against the original CT image of the same patient on a voxel-by-voxel basis. The proposed method produces a mean absolute error (MAE) of 98.6±26.9 HU overall. The accuracy is comparable with a conventional implementation scheme, but the computation time is reduced from over an hour to four minutes. Conclusion: An average atlas space patch fusion approach can produce highly accurate sCT estimations very efficiently. Further validation on dose computation accuracy and using a larger patient cohort is warranted. The author is a full time employee of Elekta, Inc.« less

Extending solid state laser performance

NASA Astrophysics Data System (ADS)

Miesak, Ed

2017-02-01

Coherent Diode-Pumped Solid-State Orlando (CDO), formerly known as Lee Laser, headquartered in Orlando Florida produces CW and pulsed solid state lasers. Primary wavelengths include 1064 nm, 532 nm, and 355 nm. Other wavelengths produced include 1320 nm, 15xx nm, and 16xx nm. Pulse widths are in the range of singles to hundreds of nanoseconds. Average powers are in the range of a few watts to 1000 watts. Pulse repetition rates are typically in the range of 100 Hz to 100 KHz. Laser performance parameters are often modified according to customer requests. Laser parameters that can be adjusted include average power, pulse repetition rate, pulse length, beam quality, and wavelength. Laser parameters are typically cross-coupled such that adjusting one may change some or all of the others. Customers often request one or more parameters be changed without changing any of the remaining parameters. CDO has learned how to accomplish this successfully with rapid turn-around times and minimal cost impact. The experience gained by accommodating customer requests has produced a textbook of cause and effect combinations of laser components to accomplish almost any parameter change request. Understanding the relationships between component combinations provides valuable insight into lasing effects allowing designers to extend laser performance beyond what is currently available. This has led to several break through products, i.e. >150W average power 355 nm, >60W average power 6 ps 1064 nm, pulse lengths longer than 400 ns at 532 nm with average power >100W, >400W 532 nm with pulse lengths in the 100 ns range.

Research and Development of Ultra-High Strength X100 Welded Pipe

NASA Astrophysics Data System (ADS)

Chuanguo, Zhang; Lei, Zheng; Ping, Hu; Bei, Zhang; Kougen, Wu; Weifeng, Huang

Ultra-high strength X100 welded pipe can be used in the construction of long distance oil and gas pipeline to improve transmission capacity and reduce operation cost. By using the way of thermo-simulation and pilot rolling, the CCT (Continuous Cooling Transformation) diagram and the relationship between ACC (Accelerated Cooling) parameters, microstructure and mechanical properties were studied for the designed X100 pipeline steel with low carbon, high manganese and niobium micro-alloyed composition in lab. The analysis of CCT diagram indicates that the suitable hardness and microstructure can be obtained in the cooling rate of 20 80°C/sec. The pilot rolling results show that the ACC cooling start temperature below Ar3 phase transformation point is beneficial to increase uniform elongation, and the cooling stop temperature of 150 350°C is helpful to obtain high strength and toughness combination. Based on the research conclusions, the X100 plate and UOE pipe with dimension in O.D.1219×W.T.14.8mm, O.D.1219×W.T.17.8mm, designed for the natural gas transmission pipeline, were trial produced. The manufactured pipe body impact absorbed energy at -10°C is over 250J. The DWTT shear area ratio at 0°C is over 85%. The transverse strength meets the X100 grade requirement, and uniform elongation is over 4%. The X100 plate and UOE pipe with dimension in O.D.711×W.T.20.0mm, O.D.711×W.T.12.5mm, designed for an offshore engineering, were also trial produced. The average impact absorbed energy of pipe body at -30°C is over 200J. The average impact absorbed energy of HAZ (Heat-affected zone) and WM (Welded Seam) at -30°C is over 100J. And the good pipe shapes were obtained

Pyroclastic flows generated by gravitational instability of the 1996-97 lava dome of Soufriere Hills Volcano, Montserrat

USGS Publications Warehouse

Cole, P.D.; Calder, E.S.; Druitt, T.H.; Hoblitt, R.; Robertson, R.; Sparks, R.S.J.; Young, S.R.

1998-01-01

Numerous pyroclastic flows were produced during 1996-97 by collapse of the growing andesitic lava dome at Soufriere Hills Volcano, Montserrat. Measured deposit volumes from these flows range from 0.2 to 9 ?? 106 m3. Flows range from discrete, single pulse events to sustained large scale dome collapse events. Flows entered the sea on the eastern and southern coasts, depositing large fans of material at the coast. Small runout distance (<1 km) flows had average flow front velocities in the order of 3-10 m/s while flow fronts of the larger runout distance flows (up to 6.5 km) advanced in the order of 15-30 m/s. Many flows were locally highly erosive. Field relations show that development of the fine grained ash cloud surge component was enhanced during the larger sustained events. Periods of elevated pyroclastic flow productivity and sustained dome collapse events are linked to pulses of high magma extrusion rates.Numerous pyroclastic flows were produced during 1996-97 by collapse of the growing andesitic lava dome at Soufriere Hills Volcano, Montserrat. Measured deposit volumes from these flows range from 0.2 to 9??106 m3. Flows range from discrete, single pulse events to sustained large scale dome collapse events. Flows entered the sea on the eastern and southern coasts, depositing large fans of material at the coast. Small runout distance (<1 km) flows had average flow front velocities in the order of 3-10 m/s while flow fronts of the larger runout distance flows (up to 6.5 km) advanced in the order of 15-30 m/s. Many flows were locally highly erosive. Field relations show that development of the fine grained ash cloud surge component was enhanced during the larger sustained events. Periods of elevated dome pyroclastic flow productivity and sustained collapse events are linked to pulses of high magma extrusion rates.

Towards representative energy data: the Machiguenga study.

PubMed

Montgomery, E

1978-01-01

Representative energy data for a human population can be produced by combining randomly sampled time allocation observations with activity-specific energy expenditure measurements. Research to produce representative energy data for adults of a population of Machiguenga Indians has recently been conducted in lowland, southeastern Peru. Marked contrast was found between the sexes for average married adults in energy expended on an average day. Men spent about 3,200 kcals and women, about 1,925; ratio: 1.66 to 1. In general, men tended to work at somewhat more energetic activities and for longer periods than did women. In addition to sex-role-related task differences were contrasts in uses of technological items and in respective work settings. These representative behavior data permit direct estimates of population-level energy requirements for average days, seasons, or for 1 year.

Fuel ethanol from raw corn

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weller, C.L.; Rodda, E.D.; Steinberg, M.P.

Crude amylase preparations were produced by growing Aspergillus awamori and A. niger on raw ground whole corn. These Koji preparations were used to hydrolyze the starch of raw ground whole corn to sugars during simultaneous fermentation of the sugars to ethanol by distillers active dry yeast. Ethanol concentrations of the fermentation beers were determined with gas-chromatography. These fermentations yielded an average of 89.6% theoretical ethanol compared to control, conventional, fermentations that had an average of 89.8%. Carbon dioxide evolutions were determined with use of Alwood valves. Both the Koji and conventional fermentations produced an average of 0.48 gram of carbonmore » dioxide per gram of dry substrate starch within 72 hours. However, initially the conventional fermentation rate was greater. Koji dehydrated at 41 degrees C had no apparent detrimental effects on theoretical ethanol yield.« less

Fuel ethanol from raw corn

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weller, C.L.; Rodda, E.D.; Steinberg, M.P.

Crude amylase preparations were produced by growing Aspergillus awamori and A. niger on raw ground whole corn. These Koji preparations were used to hydrolyze the starch of raw ground whole corn to sugars during simultaneous fermentation of the sugars to ethanol by distillers active dry yeast. Ethanol concentrations of the fermentation beers were determined with gas-chromatography. These fermentations yielded an average of 89.6% theoretical ethanol compared to control, conventional, fermentations that had an average of 89.8%. Carbon dioxide evolutions were determined with use of Alwood valves. Both the Koji and conventional fermentations produced an average of 0.48 gram of carbonmore » dioxide per gram of dry substrate starch within 72 hours. However, initially the conventional fermentation rate was greater. Koji dehydrated at 41/sup 0/C had no apparent detrimental effects on theoretical ethanol yield.« less

Comparing and combining distance-based and character-based approaches for barcoding turtles.

PubMed

Reid, B N; LE, M; McCord, W P; Iverson, J B; Georges, A; Bergmann, T; Amato, G; Desalle, R; Naro-Maciel, E

2011-11-01

Molecular barcoding can serve as a powerful tool in wildlife forensics and may prove to be a vital aid in conserving organisms that are threatened by illegal wildlife trade, such as turtles (Order Testudines). We produced cytochrome oxidase subunit one (COI) sequences (650 bp) for 174 turtle species and combined these with publicly available sequences for 50 species to produce a data set representative of the breadth of the order. Variability within the barcode region was assessed, and the utility of both distance-based and character-based methods for species identification was evaluated. For species in which genetic material from more than one individual was available (n = 69), intraspecific divergences were 1.3% on average, although divergences greater than the customary 2% barcode threshold occurred within 15 species. High intraspecific divergences could indicate species with a high degree of internal genetic structure or possibly even cryptic species, although introgression is also probable in some of these taxa. Divergences between species of the same genus were 6.4% on average; however, 49 species were <2% divergent from congeners. Low levels of interspecific divergence could be caused by recent evolutionary radiations coupled with the low rates of mtDNA evolution previously observed in turtles. Complementing distance-based barcoding with character-based methods for identifying diagnostic sets of nucleotides provided better resolution in several cases where distance-based methods failed to distinguish species. An online identification engine was created to provide character-based identifications. This study constitutes the first comprehensive barcoding effort for this seriously threatened order. © 2011 Blackwell Publishing Ltd.

An investigation on the effects of air on electron energy in atmospheric pressure helium plasma jets

NASA Astrophysics Data System (ADS)

Liu, Yadi; Tan, Zhenyu; Chen, Xinxian; Li, Xiaotong; Zhang, Huimin; Pan, Jie; Wang, Xiaolong

2018-03-01

In this work, the effects of air on electron energy in the atmospheric pressure helium plasma jet produced by a needle-plane discharge system have been investigated by means of the numerical simulation based on a two-dimensional fluid model, and the air concentration dependences of the reactive species densities have also been calculated. In addition, the synergistic effects of the applied voltage and air concentration on electron energy have been explored. The present work gives the following significant results. For a fixed applied voltage, the averaged electron energy is basically a constant at air concentrations below about 0.5%, but it evidently decreases above the concentration of 0.5%. Furthermore, the averaged densities of four main reactive species O, O(1D), O2(1Δg), and N2(A3Σu+) increase with the increasing air concentration, but the increase becomes slow at air concentrations above 0.5%. The air concentration dependences of the averaged electron energy under different voltage amplitudes are similar, and for a given air concentration, the averaged electron energy increases with the increase in the voltage amplitude. For the four reactive species, the effects of the air concentration on their averaged densities are similar for a given voltage amplitude. In addition, the averaged densities of the four reactive species increase with increasing voltage amplitude for a fixed air concentration. The present work suggests that a combination of high voltage amplitude and the characteristic air concentration, 0.5% in the present discharge system, allows an expected electron energy and also generates abundant reactive species.

75 FR 23667 - Trade Adjustment Assistance for Farmers

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-04

... Agricultural Cooperative Marketing Association on behalf of apple producers in Michigan. A public hearing to... determine within 40 days whether or not increasing imports of apple juice contributed to a greater than 15 percent decrease in the national average price of apples compared to the average of the 3 preceding...

7 CFR 1435.101 - Loan rates.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Sugar Loan Program § 1435.101 Loan rates. (a) The national average loan rate for raw cane sugar produced from domestically grown sugarcane is: 18... for the 2012 crop year. (b) The national average loan rate for refined beet sugar from domestically...

7 CFR 1435.101 - Loan rates.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Sugar Loan Program § 1435.101 Loan rates. (a) The national average loan rate for raw cane sugar produced from domestically grown sugarcane is: 18... for the 2012 crop year. (b) The national average loan rate for refined beet sugar from domestically...

7 CFR 760.406 - Payment calculation.

Code of Federal Regulations, 2010 CFR

2010-01-01

... average income loss sustained by the contract grower with respect to the dead livestock. (d) The LIP... 75 percent of the average fair market value of the applicable livestock as computed using nationwide... received from the party who contracted with the producer to raise the livestock for the loss of income from...

7 CFR 760.406 - Payment calculation.

Code of Federal Regulations, 2011 CFR

2011-01-01

... average income loss sustained by the contract grower with respect to the dead livestock. (d) The LIP... 75 percent of the average fair market value of the applicable livestock as computed using nationwide... received from the party who contracted with the producer to raise the livestock for the loss of income from...

7 CFR 1435.101 - Loan rates.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Sugar Loan Program § 1435.101 Loan rates. (a) The national average loan rate for raw cane sugar produced from domestically grown sugarcane is: 18... for the 2012 crop year. (b) The national average loan rate for refined beet sugar from domestically...

7 CFR 1435.101 - Loan rates.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Sugar Loan Program § 1435.101 Loan rates. (a) The national average loan rate for raw cane sugar produced from domestically grown sugarcane is: 18... for the 2012 crop year. (b) The national average loan rate for refined beet sugar from domestically...

7 CFR 1435.101 - Loan rates.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Sugar Loan Program § 1435.101 Loan rates. (a) The national average loan rate for raw cane sugar produced from domestically grown sugarcane is: 18... for the 2012 crop year. (b) The national average loan rate for refined beet sugar from domestically...

Description and recognition of faces from 3D data

NASA Astrophysics Data System (ADS)

Coombes, Anne M.; Richards, Robin; Linney, Alfred D.; Bruce, Vicki; Fright, Rick

1992-12-01

A method based on differential geometry, is presented for mathematically describing the shape of the facial surface. Three-dimensional data for the face are collected by optical surface scanning. The method allows the segmentation of the face into regions of a particular `surface type,' according to the surface curvature. Eight different surface types are produced which all have perceptually meaningful interpretations. The correspondence of the surface type regions to the facial features are easily visualized, allowing a qualitative assessment of the face. A quantitative description of the face in terms of the surface type regions can be produced and the variation of the description between faces is demonstrated. A set of optical surface scans can be registered together and averages to produce an average male and average female face. Thus an assessment of how individuals vary from the average can be made as well as a general statement about the differences between male and female faces. This method will enable an investigation to be made as to how reliably faces can be individuated by their surface shape which, if feasible, may be the basis of an automatic system for recognizing faces. It also has applications in physical anthropology, for classification of the face, facial reconstructive surgery, to quantify the changes in a face altered by reconstructive surgery and growth, and in visual perception, to assess the recognizability of faces. Examples of some of these applications are presented.

Estimating potential Engelmann spruce seed production on the Fraser Experimental Forest, Colorado

Treesearch

Robert R. Alexander; Carleton B. Edminster; Ross K. Watkins

1986-01-01

Two good, three heavy, and two bumper spruce seed crops were produced during a 15-year period. There was considerable variability in seed crops, however. Not all locations produced good to bumper seed crops when overall yearly ratings averaged good or better; conversely, some locations produced bumper seed crops in 3 or more years. Mathematical relationships,...

40 CFR 421.73 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... produced Lead .000 .000 Zinc .000 .000 (g) Subpart G—Hard Lead Refining Slag Granulation. BAT Effluent... per billion pounds) of hard lead produced Lead .000 .000 Zinc .000 .000 (h) Subpart G—Hard Lead... any 1 day Maximum for monthly average mg/kkg (pounds per billion pounds) of hard lead produced Lead...

40 CFR 421.73 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... produced Lead .000 .000 Zinc .000 .000 (g) Subpart G—Hard Lead Refining Slag Granulation. BAT Effluent... per billion pounds) of hard lead produced Lead .000 .000 Zinc .000 .000 (h) Subpart G—Hard Lead... any 1 day Maximum for monthly average mg/kkg (pounds per billion pounds) of hard lead produced Lead...

Influence of Rainfall Product on Hydrological and Sediment Outputs when Calibrating the STREAP Rainfall Generator for the CAESAR-Lisflood Landscape Evolution Model

NASA Astrophysics Data System (ADS)

Skinner, Christopher; Peleg, Nadav; Quinn, Niall

2017-04-01

The use of Landscape Evolution Models often requires a timeseries of rainfall to drive the model. The spatial and temporal resolution of the driving data has an impact on several model outputs, including the shape of the landscape itself. Attempts to compensate for the spatiotemporal smoothing of local rainfall intensities are insufficient and may exacerbate these issues, meaning that to produce the best results the model needs to be run with data of highest spatial and temporal resolutions available. Some rainfall generators are able to produce timeseries with high spatial and temporal resolution. Observed data is used for the calibration of these generators. However, rainfall observations are highly uncertain and vary between different products (e.g. raingauges, weather radar) which may cascade through the Landscape Evolution Model. Here, we used the STREAP rainfall generator to produce high spatial (1km) and temporal (hourly) resolution ensembles of rainfall for a 50-year period, and used these to drive the CAESAR-Lisflood Landscape Evolution Model for a test catchment. Three different calibrations of STREAP were used against different products: gridded raingauge (TBR), weather radar (NIMROD), and a merged of the two. Analysis of the discharge and sediment yields from the model runs showed that the models run by STREAP calibrated by the different products were statistically significantly different, with the raingauge calibration producing 12.4 % more sediment on average over the 50-year period. The merged product produced results which were between the raingauge and radar products. The results demonstrate the importance of considering the selection of rainfall driving data on Landscape Evolution Modelling. Rainfall products are highly uncertain, different instruments will observe rainfall differently, and these uncertainties are clearly shown to cascade through the calibration of the rainfall generator and the Landscape Evolution Model. Merging raingauge and radar products is a common practise operationally, and by using features of both to calibrate the rainfall generator it is likely a more robust rainfall timeseries is produced.

Hierarchic Agglomerative Clustering Methods for Automatic Document Classification.

ERIC Educational Resources Information Center

Griffiths, Alan; And Others

1984-01-01

Considers classifications produced by application of single linkage, complete linkage, group average, and word clustering methods to Keen and Cranfield document test collections, and studies structure of hierarchies produced, extent to which methods distort input similarity matrices during classification generation, and retrieval effectiveness…

Improving consensus structure by eliminating averaging artifacts

PubMed Central

KC, Dukka B

2009-01-01

Background Common structural biology methods (i.e., NMR and molecular dynamics) often produce ensembles of molecular structures. Consequently, averaging of 3D coordinates of molecular structures (proteins and RNA) is a frequent approach to obtain a consensus structure that is representative of the ensemble. However, when the structures are averaged, artifacts can result in unrealistic local geometries, including unphysical bond lengths and angles. Results Herein, we describe a method to derive representative structures while limiting the number of artifacts. Our approach is based on a Monte Carlo simulation technique that drives a starting structure (an extended or a 'close-by' structure) towards the 'averaged structure' using a harmonic pseudo energy function. To assess the performance of the algorithm, we applied our approach to Cα models of 1364 proteins generated by the TASSER structure prediction algorithm. The average RMSD of the refined model from the native structure for the set becomes worse by a mere 0.08 Å compared to the average RMSD of the averaged structures from the native structure (3.28 Å for refined structures and 3.36 A for the averaged structures). However, the percentage of atoms involved in clashes is greatly reduced (from 63% to 1%); in fact, the majority of the refined proteins had zero clashes. Moreover, a small number (38) of refined structures resulted in lower RMSD to the native protein versus the averaged structure. Finally, compared to PULCHRA [1], our approach produces representative structure of similar RMSD quality, but with much fewer clashes. Conclusion The benchmarking results demonstrate that our approach for removing averaging artifacts can be very beneficial for the structural biology community. Furthermore, the same approach can be applied to almost any problem where averaging of 3D coordinates is performed. Namely, structure averaging is also commonly performed in RNA secondary prediction [2], which could also benefit from our approach. PMID:19267905

Comparison of hybrid and pure Monte Carlo shower generators on an event by event basis

NASA Astrophysics Data System (ADS)

Allen, J.; Drescher, H.-J.; Farrar, G.

SENECA is a hybrid air shower simulation written by H. Drescher that utilizes both Monte Carlo simulation and cascade equations. By using the cascade equations only in the high energy portion of the shower, where they are extremely accurate, SENECA is able to utilize the advantages in speed from the cascade equations yet still produce complete, three dimensional particle distributions at ground level. We present a comparison, on an event by event basis, of SENECA and CORSIKA, a well trusted MC simulation. By using the same first interaction in both SENECA and CORSIKA, the effect of the cascade equations can be studied within a single shower, rather than averages over many showers. Our study shows that for showers produced in this manner, SENECA agrees with CORSIKA to a very high accuracy as to densities, energies, and timing information for individual species of ground-level particles from both iron and proton primaries with energies between 1EeV and 100EeV. Used properly, SENECA produces ground particle distributions virtually indistinguishable from those of CORSIKA in a fraction of the time. For example, for a shower induced by a 40 EeV proton simulated with 10-6 thinning, SENECA is 10 times faster than CORSIKA.

Functional Stability Of A Mixed Microbial Consortia Producing PHA From Waste Carbon Sources

DOE Office of Scientific and Technical Information (OSTI.GOV)

David N. Thompson; Erik R. Coats; William A. Smith

2006-04-01

Polyhydroxyalkanoates (PHAs), naturally-occurring biological polyesters that are microbially synthesized from a myriad of carbon sources, can be utilized as biodegradable substitutes for petroleum-derived thermoplastics. However, current PHA commercialization schemes are limited by high feedstock costs, the requirement for aseptic reactors, and high separation and purification costs. Bacteria indigenous to municipal waste streams can accumulate large quantities of PHA under environmentally controlled conditions; hence, a potentially more environmentally-effective method of production would utilize these consortia to produce PHAs from inexpensive waste carbon sources. In this study, PHA production was accomplished in sequencing batch bioreactors utilizing mixed microbial consortia from municipal activatedmore » sludge as inoculum, in cultures grown on real wastewaters. PHA production averaged 85%, 53%, and 10% of the cell dry weight from methanol-enriched pulp-and-paper mill foul condensate, fermented municipal primary solids, and biodiesel wastewater, respectively. The PHA-producing microbial consortia were examined to explore the microbial community changes that occurred during reactor operations, employing denaturing gradient gel electrophoresis (DGGE) of 16S-rDNA from PCR-amplified DNA extracts. Distinctly different communities were observed both between and within wastewaters following enrichment. More importantly, stable functions were maintained despite the differing and contrasting microbial populations.« less

Palm tree syrup: nutritional composition of a natural edulcorant.

PubMed

Luis, G; Rubio, C; Gutiérrez, A J; Hernández, C; González-Weller, D; Revert, C; Castilla, A; Abreu, P; Hardisson, A

2012-01-01

Palm syrup is a typical product from the Canary Islands, traditionally produced from the sap of the tropical palm tree Phoenix canariensis. Its high caloric content has led to its increasing use as a health food supplement for athletes, children and elderly. Furthermore, demand for this natural syrup is continuously increasing due also to its medicinal uses in homeopathic medicine. Palm Tree syrup samples prepared with palm sap from primary producers in La Gomera island (Canary Islands, Spain) were analyzed for their nutritional composition (moisture, ash, sugars, fat, vitamins and minerals). 35 syrup samples from five different producing regions in La Gomera island were analyzed. High-performance liquid chromatography (HPLC) was used to determine sugars and vitamins and Flame Atomic Absorption Spectrophotometry (FAAS) was used to analyze the minerals. Major carbohydrates were sucrose (37.8%), glucose (9.50%) and fructose (4.80%), respectively. The presence of arabinose could not be confirmed. Niacin was the water-soluble vitamin with the highest concentration with an average content of 0.003%. Fat content was found to be under 0.20%. Potassium was the mineral with highest contents (0.45%). Results suggest that palm tree syrup can play an important role as a sugar and mineral source in human nutrition, suggesting that future applications for this product could be developed.

Cellular Response to Doping of High Porosity Foamed Alumina with Ca, P, Mg, and Si.

PubMed

Soh, Edwin; Kolos, Elizabeth; Ruys, Andrew J

2015-03-13

Foamed alumina was previously synthesised by direct foaming of sulphate salt blends varying ammonium mole fraction (AMF), foaming heating rate and sintering temperature. The optimal product was produced with 0.33AMF, foaming at 100 °C/h and sintering at 1600 °C. This product attained high porosity of 94.39%, large average pore size of 300 µm and the highest compressive strength of 384 kPa. To improve bioactivity, doping of porous alumina by soaking in dilute or saturated solutions of Ca, P, Mg, CaP or CaP + Mg was done. Saturated solutions of Ca, P, Mg, CaP and CaP + Mg were made with excess salt in distilled water and decanted. Dilute solutions were made by diluting the 100% solution to 10% concentration. Doping with Si was done using the sol gel method at 100% concentration only. Cell culture was carried out with MG63 osteosarcoma cells. Cellular response to the Si and P doped samples was positive with high cell populations and cell layer formation. The impact of doping with phosphate produced a result not previously reported. The cellular response showed that both Si and P doping improved the biocompatibility of the foamed alumina.

High-titer lactic acid production from NaOH-pretreated corn stover by Bacillus coagulans LA204 using fed-batch simultaneous saccharification and fermentation under non-sterile condition.

PubMed

Hu, Jinlong; Zhang, Zhenting; Lin, Yanxu; Zhao, Shumiao; Mei, Yuxia; Liang, Yunxiang; Peng, Nan

2015-04-01

Lactic acid (LA) is an important chemical with various industrial applications. Non-food feedstock is commercially attractive for use in LA production; however, efficient LA fermentation from lignocellulosic biomass resulting in both high yield and titer faces technical obstacles. In this study, the thermophilic bacterium Bacillus coagulans LA204 demonstrated considerable ability to ferment glucose, xylose, and cellobiose to LA. Importantly, LA204 produces LA from several NaOH-pretreated agro stovers, with remarkably high yields through simultaneous saccharification and fermentation (SSF). A fed-batch SSF process conducted at 50°C and pH 6.0, using a cellulase concentration of 30 FPU (filter paper unit)/g stover and 10 g/L yeast extract in a 5-L bioreactor, was developed to produce LA from 14.4% (w/w) NaOH-pretreated non-sterile corn stover. LA titer, yield, and average productivity reached 97.59 g/L, 0.68 g/g stover, and 1.63 g/L/h, respectively. This study presents a feasible process for lignocellulosic LA production from abundant agro stovers. Copyright © 2015 Elsevier Ltd. All rights reserved.