Effects of carbon and hafnium concentrations in wrought powder-metallurgy superalloys based on NASA 2B-11 alloy

NASA Technical Reports Server (NTRS)

Miner, R. V., Jr.

1976-01-01

A candidate alloy for advanced-temperature turbine engine disks, and four modifications of that alloy with various C and Hf concentrations were produced as cross-rolled disks from prealloyed powder that was hot isostatically compacted. The mechanical properties, microstructures, and phase relations of the alloys are discussed in terms of their C and Hf concentrations. A low-C and high-Hf modification of IIB-11 had the best balance of mechanical properties for service below about 750 C. Because of their finer grain sizes, none of the powder-metallurgy alloys produced had the high-temperature rupture strength of conventionally cast and wrought IIB-11.

A New Method to Produce Ni-Cr Ferroalloy Used for Stainless Steel Production

NASA Astrophysics Data System (ADS)

Chen, Pei-Xian; Chu, Shao-Jun; Zhang, Guo-Hua

2016-08-01

A new electrosilicothermic method has been proposed in the present paper to produce Ni-Cr ferroalloy, which can be used for the production of 300 series stainless steel. Based on this new process, the Ni-Si ferroalloy is first produced as the intermediate alloy, and then the desiliconization process of Ni-Si ferroalloy melt with chromium concentrate is carried out to generate Ni-Cr ferroalloy. The silicon content in the Ni-Si ferroalloy produced in the submerged arc furnace should be more than 15 mass% (for the propose of reducing dephosphorization), in order to make sure the phosphorus content in the subsequently produced Ni-Cr ferroalloy is less than 0.03 mass%. A high utilization ratio of Si and a high recovery ratio of Cr can be obtained after the desiliconization reaction between Ni-Si ferroalloy and chromium concentrate in the electric arc furnace (EAF)-shaking ladle (SL) process.

Extremely high myoglobin plasma concentrations producing hook effect in a critically ill patient.

PubMed

Kurt-Mangold, Michelle; Drees, Denny; Krasowski, Matthew D

2012-12-24

A 21-year old female suffered a cardiac arrest after a one week history of viral illness later shown to be caused by influenza B. The patient required extended cardiopulmonary resuscitation and had further complications including compartment syndrome. Plasma myoglobin concentration was measured using the Roche Diagnostics electrochemiluminescent myoglobin assay. The myoglobin concentration was 205,590 μg/l in an undiluted specimen, consistent with severe rhabdomyolysis. Subsequent myoglobin concentrations measured two days later showed dramatic decreases to approximately 1000 μg/l, raising suspicion of a hook effect. Dilution and re-analysis of the specimens revealed that the actual myoglobin concentrations were >395,000 μg/l, with one specimen possessing an estimated myoglobin concentration of >600,000 μg/l. Interestingly, three specimens from this patient did not show evidence of hook effect, with undiluted specimens producing myoglobin concentrations as high as 284,000 μg/l. Retrospective analysis of myoglobin results over an 8-year period did not reveal other cases with suspicion of hook effect. The case patient had the highest myoglobin concentrations out of 7301 specimens. This case illustrates that while the Roche myoglobin assay has a very wide dynamic range, hook effect can occur with extremely high concentrations of plasma myoglobin. Copyright © 2012 Elsevier B.V. All rights reserved.

Characterization of the Factors that Influence Sinapine Concentration in Rapeseed Meal during Fermentation

PubMed Central

Niu, Yanxing; Jiang, Mulan; Guo, Mian; Wan, Chuyun; Hu, Shuangxi; Jin, Hu; Huang, Fenghong

2015-01-01

We analyzed and compared the difference in sinapine concentration in rapeseed meal between the filamentous fungus, Trametes sp 48424, and the yeast, Saccharomyces cerevisiae, in both liquid and solid-state fermentation. During liquid and solid-state fermentation by Trametes sp 48424, the sinapine concentration decreased significantly. In contrast, the liquid and solid-state fermentation process by Saccharomyces cerevisiae just slightly decreased the sinapine concentration (P ≤ 0.05). After the solid-state fermented samples were dried, the concentration of sinapine in rapeseed meal decreased significantly in Saccharomyces cerevisiae. Based on the measurement of laccase activity, we observed that laccase induced the decrease in the concentration of sinapine during fermentation with Trametes sp 48424. In order to eliminate the influence of microorganisms and the metabolites produced during fermentation, high moisture rapeseed meal and the original rapeseed meal were dried at 90°C and 105°C, respectively. During drying, the concentration of sinapine in high moisture rapeseed meal decreased rapidly and we obtained a high correlation coefficient between the concentration of sinapine and loss of moisture. Our results suggest that drying and enzymes, especially laccase that is produced during the solid-state fermentation process, may be the main factors that affect the concentration of sinapine in rapeseed meal. PMID:25606856

Cyclic lipopeptide signature as fingerprinting for the screening of halotolerant Bacillus strains towards microbial enhanced oil recovery.

PubMed

Farias, Bárbara C S; Hissa, Denise C; do Nascimento, Camila T M; Oliveira, Samuel A; Zampieri, Davila; Eberlin, Marcos N; Migueleti, Deivid L S; Martins, Luiz F; Sousa, Maíra P; Moyses, Danuza N; Melo, Vânia M M

2018-02-01

Cyclic lipopeptides (CLPs) are non-ribosomal biosurfactants produced by Bacillus species that exhibit outstanding interfacial activity. The synthesis of CLPs is under genetic and environmental influence, and representatives from different families are generally co-produced, generating isoforms that differ in chemical structure and biological activities. This study to evaluate the effect of low and high NaCl concentrations on the composition and surface activity of CLPs produced by Bacillus strains TIM27, TIM49, TIM68, and ICA13 towards microbial enhanced oil recovery (MEOR). The strains were evaluated in mineral medium containing NaCl 2.7, 66, or 100 g L -1 and growth, surface tension and emulsification activity were monitored. Based on the analysis of 16S rDNA, gyrB and rpoB sequences TIM27 and TIM49 were assigned to Bacillus subtilis, TIM68 to Bacillus vallismortis, and ICA13 to Bacillus amyloliquefaciens. All strains tolerated up to 100-g L -1 NaCl, but only TIM49 and TIM68 were able to reduce surface tension at this concentration. TIM49 also showed emulsification activity at concentrations up to 66-g L -1 NaCl. ESI-MS analysis showed that the strains produced a mixture of CLPs, which presented distinct CLP profiles at low and high NaCl concentrations. High NaCl concentration favored the synthesis of surfactins and/or fengycins that correlated with the surface activities of TIM49 and TIM68, whereas low concentration favored the synthesis of iturins. Taken together, these findings suggest that the determination of CLP signatures under the expected condition of oil reservoirs can be useful in the guidance for choosing well-suited strains to MEOR.

High cell density fed-batch fermentations for lipase production: feeding strategies and oxygen transfer.

PubMed

Salehmin, M N I; Annuar, M S M; Chisti, Y

2013-11-01

This review is focused on the production of microbial lipases by high cell density fermentation. Lipases are among the most widely used of the enzyme catalysts. Although lipases are produced by animals and plants, industrial lipases are sourced almost exclusively from microorganisms. Many of the commercial lipases are produced using recombinant species. Microbial lipases are mostly produced by batch and fed-batch fermentation. Lipases are generally secreted by the cell into the extracellular environment. Thus, a crude preparation of lipases can be obtained by removing the microbial cells from the fermentation broth. This crude cell-free broth may be further concentrated and used as is, or lipases may be purified from it to various levels. For many large volume applications, lipases must be produced at extremely low cost. High cell density fermentation is a promising method for low-cost production: it allows a high concentration of the biomass and the enzyme to be attained rapidly and this eases the downstream recovery of the enzyme. High density fermentation enhances enzyme productivity compared with the traditional submerged culture batch fermentation. In production of enzymes, a high cell density is generally achieved through fed-batch operation, not through perfusion culture which is cumbersome. The feeding strategies used in fed-batch fermentations for producing lipases and the implications of these strategies are discussed. Most lipase-producing microbial fermentations require oxygen. Oxygen transfer in such fermentations is discussed.

Butanol production from concentrated lactose/whey permeate: Use of pervaporation membrane to recover and concentrate product

USDA-ARS?s Scientific Manuscript database

In these studies butanol (acetone butanol ethanol, or ABE) was produced from concentrated lactose/whey permeate containing 211 gL-1 lactose. Fermentation of such a highly concentrated lactose solution was possible due to simultaneous product removal using a pervaporation membrane. In this system a p...

Acetate production from whey lactose using co-immobilized cells of homolactic and homoacetic bacteria in a fibrous-bed bioreactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Y.; Yang, S.T.

1998-11-20

Acetate was produced from whey lactose in batch and fed-batch fermentations using co-immobilized cells of Clostridium formicoaceticum and Lactococcus lactis. The cells were immobilized in a spirally wound fibrous sheet packed in a 0.45-L column reactor, with liquid circulated through a 5-L stirred-tank fermentor. Industrial-grade nitrogen sources, including corn steep liquor, casein hydrolysate, and yeast hydrolysate, were studied as inexpensive nutrient supplements to whey permeate and acid whey. Supplementation with either 2.5% (v/v) corn steep liquor or 1.5 g/L casein hydrolysate was adequate for the cocultured fermentation. The overall acetic acid yield from lactose was 0.9 g/g, and the productivitymore » was 0.25 g/(L h). Both lactate and acetate at high concentrations inhibited the homoacetic fermentation. To overcome these inhibitions, fed-batch fermentations were used to keep lactate concentration low and to adapt cells to high-concentration acetate. The final acetate concentration obtained in the fed-batch fermentations were used to keep lactate concentration low and to adapt cells to high-concentration acetate. The final acetate concentration obtained in the fed-batch fermentation was 75 g/L, which was the highest acetate concentration ever produced by C. formicoaceticum. Even at this high acetate concentration, the overall productivity was 0.18 g/(L h) based on the total medium volume and 1.23 g/(L h) based on the fibrous-bed reactor volume. The cells isolated from the fibrous-bed bioreactor at the end of this study were more tolerant to acetic acid than the original culture used to seed the bioreactor, indicating that adaptation and natural selection of acetate-tolerant strains occurred. This cocultured fermentation process could be used to produce a low-cost acetate deicer from whey permeate and acid whey.« less

Cyclic adenosine 3′,5′-monophosphate in human lymphocytes. Alterations after phytohemagglutinin stimulation

PubMed Central

Smith, Jay W.; Steiner, Alton L.; Newberry, W. Marcus; Parker, Charles W.

1971-01-01

We have studied cyclic adenosine 3′,5′-monophosphate (cyclic AMP) concentrations in human peripheral blood lymphocytes after stimulation with phytohemagglutinin (PHA), isoproterenol, prostaglandins, and aminophylline. Purified lymphocytes were obtained by nylon fiber chromatography, and low speed centrifugation to remove platelets. Cyclic AMP levels were determined by a highly sensitive radioimmunoassay. At concentrations of 0.1-1.0 mmoles/liter isoproterenol and aminophylline produced moderate increases in cyclic AMP concentrations, whereas prostaglandins produced marked elevations. High concentrations of PHA produced 25-300% increases in cyclic AMP levels, alterations being demonstrated within 1-2 min. The early changes in cyclic AMP concentration appear to precede previously reported metabolic changes in PHA-stimulated cells. After 6 hr cyclic AMP levels in PHA-stimulated cells had usually fallen to the levels of control cells. After 24 hr the level in PHA-stimulated cells was characteristically below that of the control cells. Adenyl cyclase, the enzyme which converts ATP to cyclic AMP, was measured in lymphocyte homogenates. Adenyl cyclase activity was rapidly stimulated by fluoride, isoproterenol, prostaglandins, and PHA. Since adenyl cyclase is characteristically localized in external cell membranes, our results are consistent with an initial action of PHA at this level. PMID:4395563

Effects of pH control and concentration on microbial oil production from Chlorella vulgaris cultivated in the effluent of a low-cost organic waste fermentation system producing volatile fatty acids.

PubMed

Cho, Hyun Uk; Kim, Young Mo; Choi, Yun-Nam; Xu, Xu; Shin, Dong Yun; Park, Jong Moon

2015-05-01

The objective of this study was to investigate the feasibility of applying volatile fatty acids (VFAs) produced from low-cost organic waste to the major carbon sources of microalgae cultivation for highly efficient biofuel production. An integrated process that consists of a sewage sludge fermentation system producing VFAs (SSFV) and mixotrophic cultivation of Chlorella vulgaris (C. vulgaris) was operated to produce microbial lipids economically. The effluents from the SSFV diluted to different concentrations at the level of 100%, 50%, and 15% were prepared for the C. vulgaris cultivation and the highest biomass productivity (433±11.9 mg/L/d) was achieved in the 100% culture controlling pH at 7.0. The harvested biomass included lipid contents ranging from 12.87% to 20.01% under the three different effluent concentrations with and without pH control. The composition of fatty acids from C. vulgaris grown on the effluents from the SSFV complied with the requirements of high-quality biodiesel. These results demonstrated that VFAs produced from the SSFV are favorable carbon sources for cultivating C. vulgaris. Copyright © 2014 Elsevier Ltd. All rights reserved.

Performance of dithiocarbamate-type flocculant in treating simulated polymer flooding produced water.

PubMed

Gao, Baoyu; Jia, Yuyan; Zhang, Yongqiang; Li, Qian; Yue, Qinyan

2011-01-01

Produced water from polymer flooding is difficult to treat due to its high polymer concentration, high viscosity, and emulsified characteristics. The dithiocarbamate flocculant, DTC (T403), was prepared by the amine-terminated polyoxypropane-ether compound known as Jeffamine-T403. The product was characterized by IR spectra and elemental analysis. The DTC agent chelating with Fe2+ produced a network polymer matrix, which captured and removed oil droplets efficiently. Oil removal by the flocculent on simulated produced water with 0, 200, 500, 900 mg/L of partially hydrolyzed polyacrylamide (HPAM) was investigated for aspects of effectiveness of DTC (T403) dosage and concentrations of HPAM and Fe2+ ions in the wastewater. Results showed that HPAM had a negative influence on oil removal efficiency when DTC (T403) dosage was lower than 20 mg/L. However, residual oil concentrations in tested samples with different concentrations of HPAM all decreased below 10 mg/L when DTC (T403) dosage reached 30 mg/L. The concentration of Fe2+ in the initial wastewater had a slight effect on oil removal at the range of 2-12 mg/L. Results showed that Fe3+ could not be used in place of Fe2+ as Fe3+ could not react with DTC under flocculated conditions. The effects of mineral salts ions were also investigated.

Neurotoxicity produced by dibromoacetic acid in drinking water of rats.

PubMed

Moser, V C; Phillips, P M; Levine, A B; McDaniel, K L; Sills, R C; Jortner, B S; Butt, M T

2004-05-01

An evaluation of potential adverse human health effects of disinfection byproducts requires study of both cancer and noncancer endpoints; however, no studies have evaluated the neurotoxic potential of a common haloacetic acid, dibromoacetic acid (DBA). This study characterized the neurotoxicity of DBA during 6-month exposure in the drinking water of rats. Adolescent male and female Fischer 344 rats were administered DBA at 0, 0.2, 0.6, and 1.5 g/l. On a mg/kg/day basis, the consumed dosages decreased greatly over the exposure period, with average intakes of 0, 20, 72, and 161 mg/kg/day. Weight gain was depressed in the high-concentration group, and concentration-related diarrhea and hair loss were observed early in exposure. Testing with a functional observational battery and motor activity took place before dosing and at 1, 2, 4, and 6 months. DBA produced concentration-related neuromuscular toxicity (mid and high concentrations) characterized by limb weakness, mild gait abnormalities, and hypotonia, as well as sensorimotor depression (all concentrations), with decreased responses to a tail-pinch and click. Other signs of toxicity at the highest concentration included decreased activity and chest clasping. Neurotoxicity was evident as early as one month, but did not progress with continued exposure. The major neuropathological finding was degeneration of spinal cord nerve fibers (mid and high concentrations). Cellular vacuolization in spinal cord gray matter (mostly) and in white matter (occasionally) tracts was also observed. No treatment-related changes were seen in brain, eyes, peripheral nerves, or peripheral ganglia. The lowest-observable effect level for neurobehavioral changes was 20 mg/kg/day (produced by 0.2 g/l, lowest concentration tested), whereas this dosage was a no-effect level for neuropathological changes. These studies suggest that neurotoxicity should be considered in the overall hazard evaluation of haloacetic acids.

Methods and devices for high-throughput dielectrophoretic concentration

DOEpatents

Simmons, Blake A.; Cummings, Eric B.; Fiechtner, Gregory J.; Fintschenko, Yolanda; McGraw, Gregory J.; Salmi, Allen

2010-02-23

Disclosed herein are methods and devices for assaying and concentrating analytes in a fluid sample using dielectrophoresis. As disclosed, the methods and devices utilize substrates having a plurality of pores through which analytes can be selectively prevented from passing, or inhibited, on application of an appropriate electric field waveform. The pores of the substrate produce nonuniform electric field having local extrema located near the pores. These nonuniform fields drive dielectrophoresis, which produces the inhibition. Arrangements of electrodes and porous substrates support continuous, bulk, multi-dimensional, and staged selective concentration.

Mist characterization in drilling 1018 steel

NASA Astrophysics Data System (ADS)

Cole, Ian

Minimum quantity lubrication replaces the traditional method of flood cooling with small amounts of high-efficient lubrication. Limited studies have been performed to determine the characteristics of mist produced during MQL. This study investigated the mist concentration levels produced while drilling 1018 steel using a vegetable based lubricant. ANOVA was performed to determine whether speed and feed rates or their interactions have a significant effect on mist concentration levels and particle diameter. It was observed that the concentration levels obtained under all four speed and feed rate combinations studied exceeded the current OSHA and NIOSH standards.

Process for hydrocracking carbonaceous material to provide fuels or chemical feed stock

DOEpatents

Duncan, Dennis A.

1980-01-01

A process is disclosed for hydrocracking coal or other carbonaceous material to produce various aromatic hydrocarbons including benzene, toluene, xylene, ethylbenzene, phenol and cresols in variable relative concentrations while maintaining a near constant maximum temperature. Variations in relative aromatic concentrations are achieved by changing the kinetic severity of the hydrocracking reaction by altering the temperature profile up to and quenching from the final hydrocracking temperature. The relative concentration of benzene to the alkyl and hydroxyl aromatics is increased by imposing increased kinetic severity above that corresponding to constant heating rate followed by immediate quenching at about the same rate to below the temperature at which dehydroxylation and dealkylation reactions appreciably occur. Similarly phenols, cresols and xylenes are produced in enhanced concentrations by adjusting the temperature profile to provide a reduced kinetic severity relative to that employed when high benzene concentrations are desired. These variations in concentrations can be used to produce desired materials for chemical feed stocks or for fuels.

Heart Rate Response and Lactic Acid Concentration in Squash Players.

ERIC Educational Resources Information Center

Beaudin, Paula; And Others

1978-01-01

It was concluded that playing squash is an activity that results in heart rate responses of sufficient intensity to elicit aerobic training effects without producing high lactic acid concentration in the blood. (MM)

Planar concentrators at the étendue limit

NASA Astrophysics Data System (ADS)

Winston, Roland; Gordon, Jeffrey M.

2005-08-01

Recently proposed aplanatic imaging designs are integrally combined with nonimaging flux boosters to produce an ultra-compact planar dielectric-filled concentrator that performs near the étendue limit. Such optical devices are attractive for high-efficiency multi-junction photovoltaics at high flux, with realistic power generation of 1 W from a 1 mm2 cell.

Production of fullerenes with concentrated solar flux

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hale, M. J.; Fields, C.; Lewandowski, A.

1994-01-01

Research at the National Renewable Energy Laboratory (NREL) has demonstrated that fullerenes can be produced using highly concentrated sunlight from a solar furnace. Since they were first synthesized in 1989, fullerenes have been the subject of intense research. They show considerable commercial potential in advanced materials and have potential applications that include semiconductors, superconductors, high-performance metals, and medical technologies. The most common fullerene is C{sub 60}, which is a molecule with a geometry resembling a soccer ball. Graphite vaporization methods such as pulsed-laser vaporization, resistive heating, and carbon arc have been used to produce fullerenes. None of these, however, seemsmore » capable of producing fullerenes economically on a large scale. The use of concentrated sunlight may help avoid the scale-up limitations inherent in more established production processes. Recently, researchers at NREL made fullerenes in NREL`s 10 kW High Flux Solar Furnace (HFSF) with a vacuum reaction chamber designed to deliver a solar flux of 1200 W/cm{sup 2} to a graphite pellet. Analysis of the resulting carbon soot by mass spectrometry and high-pressure liquid chromatography confirmed the existence of fullerenes. These results are very encouraging and we are optimistic that concentrated solar flux can provide a means for large-scale, economical production of fullerenes. This paper presents our method, experimental apparatus, and results of fullerene production research performed with the HFSF.« less

Pilot scale high solids anaerobic digestion of steam autoclaved municipal solid waste (MSW) pulp

USDA-ARS?s Scientific Manuscript database

Steam autoclaving is an efficient method for the separation and recovery of nearly all organics from MSW, yet a reliable alternative outlet for the large volume of organics produced has not yet been successfully demonstrated. The material produced by the autoclave contains a high concentration of s...

Process for producing a clean hydrocarbon fuel from high calcium coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kindig, J.K.

A method is described for substantially reducing the amount of at least one insoluble fluoride-forming species selected from the group consisting of Group IA species and Group IIA species. The species is present in a coal feed material comprising: forming a slurry of a coal feed; a fluoride acid in an amount to produce a first molar concentration of free-fluoride-ions; at least one fluoride-complexing species, the total of all fluoride-complexing species in the slurry being present in an amount to produce a second molar concentration, the second molar concentration being at least equal to that amount such that the ratiomore » of the first molar concentration to the second molar concentration is substantially equal to the stoichiometric ratio of fluoride in at least one tightly-bound complexion so as to from tightly-bound complexions with substantially all free-fluoride ions in the slurry to produce a leached coal product and a spent leach liquor; and separating the leached coal product from the spent leach liquor.« less

Lead-210 and polonium-210 in biological samples from Alaska.

PubMed

Beasley, T M; Palmer, H E

1966-05-20

The naturally occurring concentrations of lead-210 and polonium-210 in certain biological samples from Alaska are unusually high. The concentration processes are similar to those observed for artificially produced radioactive fallout. Concentrations of these nuclides are greater in Alaskan natives than they are in other United States residents.

Tissue-Culture Method of Cloning Rubber Plants

NASA Technical Reports Server (NTRS)

Ball, E. A.

1983-01-01

Guayule plant, a high-yield rubber plant cloned by tissue-culture method to produce multiple new plants that mature quickly. By adjusting culture medium, excised shoot tip produces up to 50 identical guayule plants. Varying concentration of cytokinin, single excised tip produces either 1 or several (up to 50) new plants.

Tailoring Microbial Electrochemical Cells for Production of Hydrogen Peroxide at High Concentrations and Efficiencies.

PubMed

Young, Michelle N; Links, Mikaela J; Popat, Sudeep C; Rittmann, Bruce E; Torres, César I

2016-12-08

A microbial peroxide producing cell (MPPC) for H 2 O 2 production at the cathode was systematically optimized with minimal energy input. First, the stability of H 2 O 2 was evaluated using different catholytes, membranes, and catalyst materials. On the basis of these results, a flat-plate MPPC fed continuously using 200 mm NaCl catholyte at a 4 h hydraulic retention time was designed and operated, producing H 2 O 2 for 18 days. H 2 O 2 concentration of 3.1 g L -1 H 2 O 2 with 1.1 Wh g -1 H 2 O 2 power input was achieved in the MPPC. The high H 2 O 2 concentration was a result of the optimum materials selected. The small energy input was largely the result of the 0.5 cm distance between the anode and cathode, which reduced ionic transport losses. However, >50 % of operational overpotentials were due to the 4.5-5 pH unit difference between the anode and cathode chambers. The results demonstrate that a MPPC can continuously produce H 2 O 2 at high concentration by selecting compatible materials and appropriate operating conditions. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Planar concentrators near the étendue limit.

PubMed

Winston, Roland; Gordon, Jeffrey M

2005-10-01

Recently proposed aplanatic imaging designs are integrally combined with nonimaging flux boosters to produce an ultracompact planar glass-filled concentrator that performs near the étendue limit. Such optical devices are attractive for high-efficiency multijunction photovoltaics at high flux, with realistic power generation of 1 W from a 1 mm2 cell. When deployed in reverse, our designs provide collimation even for high-numerical-aperture light sources.

Planar concentrators near the étendue limit

NASA Astrophysics Data System (ADS)

Winston, Roland; Gordon, Jeffrey M.

2005-10-01

Recently proposed aplanatic imaging designs are integrally combined with nonimaging flux boosters to produce an ultracompact planar glass-filled concentrator that performs near the étendue limit. Such optical devices are attractive for high-efficiency multijunction photovoltaics at high flux, with realistic power generation of 1 W from a 1 mm² cell. When deployed in reverse, our designs provide collimation even for high-numerical-aperture light sources.

Use of inorganic Fullerene-like WS2 to produce new high-performance polyphenylene sulfide nanocomposites: role of the nanoparticle concentration.

PubMed

Naffakh, Mohammed; Marco, Carlos; Gómez, Marián A; Gómez-Herrero, Julio; Jiménez, Ignacio

2009-07-30

The use of tungsten disulfide (WS2) nanoparticles offers the opportunity to produce novel and advanced polymer-based nanocomposite materials via melt blending. The developed materials, based on the high-performance engineering thermoplastic polyphenylene sulfide (PPS), display a unique nanostructure on variation of the nanoparticle concentration, as confirmed by time-resolved synchrotron X-ray diffraction. The cold-crystallization kinetics and morphology of PPS chains under confined conditions in the nanocomposite, as determined by differential scanning calorimetry (DSC) and atomic force microscopy (AFM), also manifest a dependence on the IF-WS2 concentration which are unexpected for polymer nanocomposites. The addition of IF-WS2 with concentrations greater than or equal to 0.5 wt % of IF-WS2 remarkably improves the mechanical performance of PPS with an increase in the storage modulus of 40-75%.

No difference between high-fructose and high-glucose diets on liver triacylglycerol or biochemistry in healthy overweight men.

PubMed

Johnston, Richard D; Stephenson, Mary C; Crossland, Hannah; Cordon, Sally M; Palcidi, Elisa; Cox, Eleanor F; Taylor, Moira A; Aithal, Guruprasad P; Macdonald, Ian A

2013-11-01

Diets high in fructose have been proposed to contribute to nonalcoholic fatty liver disease. We compared the effects of high-fructose and matched glucose intake on hepatic triacylglycerol (TAG) concentration and other liver parameters. In a double-blind study, we randomly assigned 32 healthy but centrally overweight men to groups that received either a high-fructose or high-glucose diet (25% energy). These diets were provided during an initial isocaloric period of 2 weeks, followed by a 6-week washout period, and then again during a hypercaloric 2-week period. The primary outcome measure was hepatic level of TAG, with additional assessments of TAG levels in serum and soleus muscle, hepatic levels of adenosine triphosphate, and systemic and hepatic insulin resistance. During the isocaloric period of the study, both groups had stable body weights and concentrations of TAG in liver, serum, and soleus muscle. The high-fructose diet produced an increase of 22 ± 52 μmol/L in the serum level of uric acid, whereas the high-glucose diet led to a reduction of 23 ± 25 μmol/L (P < .01). The high-fructose diet also produced an increase of 0.8 ± 0.9 in the homeostasis model assessment of insulin resistance, whereas the high-glucose diet produced an increase of only 0.1 ± 0.7 (P = .03). During the hypercaloric period, participants in the high-fructose and high-glucose groups had similar increases in weight (1.0 ± 1.4 vs 0.6 ± 1.0 kg; P = .29) and absolute concentration of TAG in liver (1.70% ± 2.6% vs 2.05% ± 2.9%; P = .73) and serum (0.36 ± 0.75 vs 0.33 ± 0.38 mmol/L; P = .91), and similar results in biochemical assays of liver function. Body weight changes were associated with changes in liver biochemistry and concentration of TAGs. In the isocaloric period, overweight men who were on a high-fructose or a high-glucose diet did not develop any significant changes in hepatic concentration of TAGs or serum levels of liver enzymes. However, in the hypercaloric period, both high-fructose and high-glucose diets produced significant increases in these parameters without any significant difference between the 2 groups. This indicates an energy-mediated, rather than a specific macronutrient-mediated, effect. Clinical trials.gov no: NCT01050140. Copyright © 2013 AGA Institute. Published by Elsevier Inc. All rights reserved.

Aquaporins in desert rodent physiology.

PubMed

Pannabecker, Thomas L

2015-08-01

Desert rodents face a sizeable challenge in maintaining salt and water homeostasis due to their life in an arid environment. A number of their organ systems exhibit functional characteristics that limit water loss above that which occurs in non-desert species under similar conditions. These systems include renal, pulmonary, gastrointestinal, nasal, and skin epithelia. The desert rodent kidney preserves body water by producing a highly concentrated urine that reaches a maximum osmolality nearly three times that of the common laboratory rat. The precise mechanism by which urine is concentrated in any mammal is unknown. Insights into the process may be more apparent in species that produce highly concentrated urine. Aquaporin water channels play a fundamental role in water transport in several desert rodent organ systems. The role of aquaporins in facilitating highly effective water preservation in desert rodents is only beginning to be explored. The organ systems of desert rodents and their associated AQPs are described. © 2015 Marine Biological Laboratory.

Application of alkyne-TCNQ addition reaction to polymerization.

PubMed

Washino, Yusuke; Michinobu, Tsuyoshi

2011-04-19

The polymerization using a high-yielding addition reaction between electron-rich alkynes and 7,7,8,8-tetracyanoquinodimethane (TCNQ) derivatives is described. The bifunctional monomer containing two TCNQ moieties and the counter comonomer bearing two dialkylaniline (DAA)-substituted alkynes are reacted in 1,2-dichloroethane under mild heating conditions. At the high monomer concentrations, high molecular weight linear polymers are obtained, while the reaction at the low monomer concentrations produces a significant amount of the cyclic compounds. A clear relationship between the monomer concentration and the cyclic compound amount is demonstrated. The obtained polymers feature a sufficient thermal stability with the decomposition temperature exceeding 300  °C as well as strong charge-transfer (CT) bands and redox activities ascribed to the produced donor-acceptor moieties. These features are also used to optimize the polymerization conditions and to estimate the chemical structures. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Strategies for the production of high concentrations of bioethanol from seaweeds

PubMed Central

Yanagisawa, Mitsunori; Kawai, Shigeyuki; Murata, Kousaku

2013-01-01

Bioethanol has attracted attention as an alternative to petroleum-derived fuel. Seaweeds have been proposed as some of the most promising raw materials for bioethanol production because they have several advantages over lignocellulosic biomass. However, because seaweeds contain low contents of glucans, i.e., polysaccharides composed of glucose, the conversion of only the glucans from seaweed is not sufficient to produce high concentrations of ethanol. Therefore, it is also necessary to produce ethanol from other specific carbohydrate components of seaweeds, including sulfated polysaccharides, mannitol, alginate, agar and carrageenan. This review summarizes the current state of research on the production of ethanol from seaweed carbohydrates for which the conversion of carbohydrates to sugars is a key step and makes comparisons with the production of ethanol from lignocellulosic biomass. This review provides valuable information necessary for the production of high concentrations of ethanol from seaweeds. PMID:23314751

Ligninolytic enzyme production in selected sub-tropical white rot fungi under different culture conditions.

PubMed

Tekere, M; Zvauya, R; Read, J S

2001-01-01

Lignin peroxidase (LiP), manganese peroxidase (MnP) and laccase activities in selected sub-tropical white rot fungal species from Zimbabwe were determined. The enzyme activities were assayed at varying concentrations of C, N and Mn2+. Manganese peroxidase and laccase activities were the only expressed activities in the fungi under the culture conditions tested. Trametes species, T. cingulata, T. elegans and T. pocas produced the highest manganese peroxidase activities in a medium containing high carbon and low nitrogen conditions. High nitrogen conditions favoured high manganese peroxidase activity in DSPM95, L. velutinus and Irpex spp. High manganese peroxidase activity was notable for T. versicolor when both carbon and nitrogen in the medium were present at high levels. Laccase production by the isolates was highest under conditions of high nitrogen and those conditions with both nitrogen and carbon at high concentration. Mn2+ concentrations between 11-25 ppm gave the highest manganese peroxidase activity compared to a concentration of 40 ppm or when there was no Mn2+ added. Laccase activity was less influenced by Mn2+ levels. While some laccase activity was produced in the absence of Mn2+, the enzyme levels were higher when Mn2+ was added to the culture medium.

Production of L-lactic Acid from Biomass Wastes Using Scallop Crude Enzymes and Novel Lactic Acid Bacterium

NASA Astrophysics Data System (ADS)

Yanagisawa, Mitsunori; Nakamura, Kanami; Nakasaki, Kiyohiko

In the present study, biomass waste raw materials including paper mill sludge, bamboo, sea lettuce, and shochu residue (from a distiller) and crude enzymes derived from inedible and discarded scallop parts were used to produce L-lactic acid for the raw material of biodegradable plastic poly-lactic acid. The activities of cellulase and amylase in the crude enzymes were 22 and 170units/L, respectively, and L-lactic acid was produced from every of the above mentioned biomass wastes, by the method of liquid-state simultaneous saccharification and fermentation (SSF) . The L-lactic acid concentrations produced from sea lettuce and shochu residue, which contain high concentration of starch were 3.6 and 9.3g/L, respectively, and corresponded to greater than 25% of the conversion of glucans contained in these biomass wastes. Furthermore, using the solid state SSF method, concentrations as high as 13g/L of L-lactic acid were obtained from sea lettuce and 26g/L were obtained from shochu residue.

Inoculum Effect on the Efficacies of Amoxicillin-Clavulanate, Piperacillin-Tazobactam, and Imipenem against Extended-Spectrum β-Lactamase (ESBL)-Producing and Non-ESBL-Producing Escherichia coli in an Experimental Murine Sepsis Model

PubMed Central

López-Cerero, L.; López-Rojas, R.; Egea, P.; Domínguez-Herrera, J.; Rodríguez-Baño, J.; Pascual, A.; Pachón, J.

2013-01-01

Escherichia coli is commonly involved in infections with a heavy bacterial burden. Piperacillin-tazobactam and carbapenems are among the recommended empirical treatments for health care-associated complicated intra-abdominal infections. In contrast to amoxicillin-clavulanate, both have reduced in vitro activity in the presence of high concentrations of extended-spectrum β-lactamase (ESBL)-producing and non-ESBL-producing E. coli bacteria. Our goal was to compare the efficacy of these antimicrobials against different concentrations of two clinical E. coli strains, one an ESBL-producer and the other a non-ESBL-producer, in a murine sepsis model. An experimental sepsis model {∼5.5 log10 CFU/g [low inoculum concentration (LI)] or ∼7.5 log10 CFU/g [high inoculum concentration (HI)]} using E. coli strains ATCC 25922 (non-ESBL producer) and Ec1062 (CTX-M-14 producer), which are susceptible to the three antimicrobials, was used. Amoxicillin-clavulanate (50/12.5 mg/kg given intramuscularly [i.m.]), piperacillin-tazobactam (25/3.125 mg/kg given intraperitoneally [i.p.]), and imipenem (30 mg/kg i.m.) were used. Piperacillin-tazobactam and imipenem reduced spleen ATCC 25922 strain concentrations (−2.53 and −2.14 log10 CFU/g [P < 0.05, respectively]) in the HI versus LI groups, while amoxicillin-clavulanate maintained its efficacy (−1.01 log10 CFU/g [no statistically significant difference]). Regarding the Ec1062 strain, the antimicrobials showed lower efficacy in the HI than in the LI groups: −0.73, −1.89, and −1.62 log10 CFU/g (P < 0.05, for piperacillin-tazobactam, imipenem, and amoxicillin-clavulanate, respectively, although imipenem and amoxicillin-clavulanate were more efficacious than piperacillin-tazobactam). An adapted imipenem treatment (based on the time for which the serum drug concentration remained above the MIC obtained with a HI of the ATCC 25922 strain) improved its efficacy to −1.67 log10 CFU/g (P < 0.05). These results suggest that amoxicillin-clavulanate could be an alternative to imipenem treatment of infections caused by ESBL- and non-ESBL-producing E. coli strains in patients with therapeutic failure with piperacillin-tazobactam. PMID:23439636

Inoculum effect on the efficacies of amoxicillin-clavulanate, piperacillin-tazobactam, and imipenem against extended-spectrum β-lactamase (ESBL)-producing and non-ESBL-producing Escherichia coli in an experimental murine sepsis model.

PubMed

Docobo-Pérez, F; López-Cerero, L; López-Rojas, R; Egea, P; Domínguez-Herrera, J; Rodríguez-Baño, J; Pascual, A; Pachón, J

2013-05-01

Escherichia coli is commonly involved in infections with a heavy bacterial burden. Piperacillin-tazobactam and carbapenems are among the recommended empirical treatments for health care-associated complicated intra-abdominal infections. In contrast to amoxicillin-clavulanate, both have reduced in vitro activity in the presence of high concentrations of extended-spectrum β-lactamase (ESBL)-producing and non-ESBL-producing E. coli bacteria. Our goal was to compare the efficacy of these antimicrobials against different concentrations of two clinical E. coli strains, one an ESBL-producer and the other a non-ESBL-producer, in a murine sepsis model. An experimental sepsis model {~5.5 log10 CFU/g [low inoculum concentration (LI)] or ~7.5 log(10) CFU/g [high inoculum concentration (HI)]} using E. coli strains ATCC 25922 (non-ESBL producer) and Ec1062 (CTX-M-14 producer), which are susceptible to the three antimicrobials, was used. Amoxicillin-clavulanate (50/12.5 mg/kg given intramuscularly [i.m.]), piperacillin-tazobactam (25/3.125 mg/kg given intraperitoneally [i.p.]), and imipenem (30 mg/kg i.m.) were used. Piperacillin-tazobactam and imipenem reduced spleen ATCC 25922 strain concentrations (-2.53 and -2.14 log10 CFU/g [P < 0.05, respectively]) in the HI versus LI groups, while amoxicillin-clavulanate maintained its efficacy (-1.01 log10 CFU/g [no statistically significant difference]). Regarding the Ec1062 strain, the antimicrobials showed lower efficacy in the HI than in the LI groups: -0.73, -1.89, and -1.62 log10 CFU/g (P < 0.05, for piperacillin-tazobactam, imipenem, and amoxicillin-clavulanate, respectively, although imipenem and amoxicillin-clavulanate were more efficacious than piperacillin-tazobactam). An adapted imipenem treatment (based on the time for which the serum drug concentration remained above the MIC obtained with a HI of the ATCC 25922 strain) improved its efficacy to -1.67 log10 CFU/g (P < 0.05). These results suggest that amoxicillin-clavulanate could be an alternative to imipenem treatment of infections caused by ESBL- and non-ESBL-producing E. coli strains in patients with therapeutic failure with piperacillin-tazobactam.

Association of circulating concentrations of estradiol during the preovulatory period and expression of steroidogenic enzymes in beef cows

USDA-ARS?s Scientific Manuscript database

Cows with greater circulating concentrations of estradiol during the preovulatory period (HighE2) have increased pregnancy success following a fixed-time AI protocol. Furthermore, these animals have an enhanced ability to produce estradiol as indicated by increased expression of CYP19A1 and LHR wit...

Blood harmane, blood lead, and severity of hand tremor: evidence of additive effects.

PubMed

Louis, Elan D; Factor-Litvak, Pam; Gerbin, Marina; Slavkovich, Vesna; Graziano, Joseph H; Jiang, Wendy; Zheng, Wei

2011-03-01

Tremor is a widespread phenomenon in human populations. Environmental factors are likely to play an etiological role. Harmane (1-methyl-9H-pyrido[3,4-β]indole) is a potent tremor-producing β-carboline alkaloid. Lead is another tremor-producing neurotoxicant. The effects of harmane and lead with respect to tremor have been studied in isolation. We tested the hypothesis that tremor would be particularly severe among individuals who had high blood concentrations of both of these toxicants. Blood concentrations of harmane and lead were each quantified in 257 individuals (106 essential tremor cases and 151 controls) enrolled in an environmental epidemiological study. Total tremor score (range = 0-36) was a clinical measure of tremor severity. The total tremor score ranged from 0 to 36, indicating that a full spectrum of tremor severities was captured in our sample. Blood harmane concentration correlated with total tremor score (p = 0.007), as did blood lead concentration (p = 0.045). The total tremor score was lowest in participants with both low blood harmane and lead concentrations (8.4 ± 8.2), intermediate in participants with high concentrations of either toxicant (10.5 ± 9.8), and highest in participants with high concentrations of both toxicants (13.7 ± 10.4) (p=0.01). Blood harmane and lead concentrations separately correlated with total tremor scores. Participants with high blood concentrations of both toxicants had the highest tremor scores, suggesting an additive effect of these toxicants on tremor severity. Given the very high population prevalence of tremor disorders, identifying environmental determinants is important for primary disease prevention. Copyright © 2010 Elsevier Inc. All rights reserved.

Blood Harmane, Blood Lead, and Severity of Hand Tremor: Evidence of Additive Effects

PubMed Central

Louis, Elan D.; Factor-Litvak, Pam; Gerbin, Marina; Slavkovich, Vesna; Graziano, Joseph H; Jiang, Wendy; Zheng, Wei

2010-01-01

Background Tremor is a widespread phenomenon in human populations. Environmental factors are likely to play an etiological role. Harmane (1-methyl-9H-pyrido[3,4-β]indole) is a potent tremor-producing β-carboline alkaloid. Lead is another tremor-producing neurotoxicant. The effects of harmane and lead with respect to tremor have been studied in isolation. Objectives We tested the hypothesis that tremor would be particularly severe among individuals who had high blood concentrations of both of these toxicants. Methods Blood concentrations of harmane and lead were each quantified in 257 individuals (106 essential tremor cases and 151 controls) enrolled in an environmental epidemiological study. Total tremor score (range = 0 – 36) was a clinical measure of tremor severity. Results The total tremor score ranged from 0 – 36, indicating that a full spectrum of tremor severities was captured in our sample. Blood harmane concentration correlated with total tremor score (p = 0.007), as did blood lead concentration (p = 0.045). The total tremor score was lowest in participants with both low blood harmane and lead concentrations (8.4 ± 8.2), intermediate in participants with high concentrations of either toxicant (10.5 ± 9.8), and highest in participants with high concentrations of both toxicants (13.7 ± 10.4)(p = 0.01). Conclusions Blood harmane and lead concentrations separately correlated with total tremor scores. Participants with high blood concentrations of both toxicants had the highest tremor scores, suggesting an additive effect of these toxicants on tremor severity. Given the very high population prevalence of tremor disorders, identifying environmental determinants is important for primary disease prevention. PMID:21145352

The relationship between serum adiponectin and postpartum luteal activity in high-producing dairy cows.

PubMed

Kafi, Mojtaba; Tamadon, Amin; Saeb, Mehdi

2015-05-01

The aims of the present study were to initially determine the pattern of serum adiponectin concentrations during a normal estrous cycle in high-producing postpartum dairy cows and then evaluate the relationship between the serum concentrations of adiponectin and insulin with the commencement of postpartum luteal activity and ovarian activities in clinically healthy high-producing Holstein dairy cows. During a normal estrous cycle of cows (n = 6), serum adiponectin concentrations gradually decreased (P < 0.05) after ovulation by Day-17 estrous cycle and then increased before the next ovulation. Cows with higher peak of milk yield had lower serum adiponectin concentrations by week 7 postpartum (P = 0.01). Serum adiponectin and insulin concentrations in cows with different postpartum luteal activity (based on the progesterone profile) were evaluated using the following class of cows: normal (≤45 days, n = 11) and delayed (>45 days, n = 11) commencement of luteal activity (C-LA) and four different profiles of normal luteal activity (NLA, n = 5), prolonged luteal phase (n = 6), delayed first ovulation (n = 6), and anovulation (AOV, n = 5). Serum adiponectin concentrations decreased gradually by week 3 postpartum in NLA and then increased; whereas in AOV and delayed first ovulation, they were decreased after week 3 postpartum (P < 0.05). Moreover, serum adiponectin concentrations in NLA were more than AOV at weeks 5 and 7 postpartum (P = 0.05). The increase in the milk yield from weeks 1 to 7 postpartum in prolonged luteal phase (P = 0.05) and AOV (P = 0.04) cows was more than that of NLA cows. Insulin concentrations were almost maintained at a stable level in NLA cows (P > 0.05), whereas they increased in the other groups (P < 0.05). Moreover, adiponectin concentrations in cows with C-LA greater than 45 days decreased more than those with C-LA 45 days or less after week 3 postpartum (P = 0.002). Serum adiponectin concentrations at week 7 postpartum were lower in delayed C-LA (P = 0.01). Milk yield in cows with C-LA greater than 45 days increased more than cows with C-LA 45 days or less postpartum (P = 0.002). Insulin concentrations increased relatively in parallel from weeks 1 to 7 postpartum in cows either with C-LA greater than 45 or with C-LA 45 days or less. We showed for the first time the profile of serum adiponectin concentrations in a normal estrous cycle of dairy cows, and furthermore, it was found that high-producing dairy cows with higher postpartum serum adiponectin concentrations had NLA and earlier C-LA. Copyright © 2015 Elsevier Inc. All rights reserved.

The influence of HCl concentration and demineralization temperature of Atrina pectinata shells on quality of chitin

NASA Astrophysics Data System (ADS)

Nugroho, Intan Lazuardi; Pursetyo, Kustiawan Tri; Masithah, Endang Dewi

2017-02-01

Atrina pectinata is one of shells species widely consumed by people, which means the high consumption will generate the availability of shells in the environment as waste. Chitin can be produced from the shells. Shells contain quite high minerals that it should be demineralized to reduce the mineral content from the shells. This study aimed to determine the effect of HCl concentration and temperature affect chitin characteristics as the result of demineralization process from pen shells. The method based on two steps, there were demineralization and deproteination. This study used Completely Randomized Design (CRD) with two factors, including HCl concentration (2N, 4N, and 6N) and temperature (33°C and 60°C) which consists six combination treatments and three replications. Data was analyzed by using Analysis of Variance (ANOVA) and followed by Duncan's Multiple Range Test. The results showed that interaction of HCl concentration and temperature has significant effect (p<0.05) to ash content of chitin. The use concentration of 6N and 33°C produced the lowest ash content. Characteristics chitin resulted from the treatment of 6N and 33°C produced ash content 25.33% ± 6.82, moisture content 3.67% ± 1.10, yield 0.72% ± 0.12 and protein content 5.86%.

Susceptibility of Haemophilus influenzae to chloramphenicol and eight beta-lactam antibiotics.

PubMed Central

Thirumoorthi, M C; Kobos, D M; Dajani, A S

1981-01-01

We examined the minimal inhibitory concentrations and minimal bactericidal concentrations of chloramphenicol, ampicillin, ticarcillin, cefamandole, cefazolin, cefoxitin, cefotaxime, ceforanide, and moxalactam for 100 isolates of Haemophilus influenzae, 25 of which produced beta-lactamase. Susceptibility was not influenced by the capsular characteristic of the organism. The mean minimal inhibitory concentrations of cefamandole, ticarcillin, and ampicillin for beta-lactamase-producing strains were 3-, 120-, and 400-fold higher than their respective mean minimal inhibitory concentrations for beta-lactamase-negative strains. No such difference was noted for the other antibiotics. We performed time-kill curve studies, using chloramphenicol, ampicillin, cefamandole, cefotaxime, and moxalactam with two concentrations of the antimicrobial agents (4 or 20 times the minimal inhibitory concentrations) and two inoculum sizes (10(4) or 10(6) colony-forming units per ml). The inoculum size had no appreciable effect on the rate of killing of beta-lactamase-negative strains. The rates at which beta-lactamase-producing strains were killed by chloramphenicol, cefotaxime, and moxalactam was not influenced by the inoculum size. Whereas cefamandole in high concentrations was able to kill at 10(6) colony-forming units/ml of inoculum, it had only a temporary inhibiting effect at low drug concentrations. Methicillin and the beta-lactamase inhibitor CP-45,899 were able to neutralize the inactivation of cefamandole by a large inoculum of beta-lactamase-producing H. influenzae. PMID:6974541

Development of Rapid Radiochemical Method for Gross Alpha and Gross Beta Activity Concentration in Flowback and Produced Waters from Hydraulic Fracturing Operations

EPA Science Inventory

This report summarizes the development and validation of an improved method for the Determination of Gross Alpha and Gross Beta Activity in Flowback and Produced Waters from Hydraulic Fracturing Operations (FPWHFO). Flowback and produced waters are characterized by high concentra...

Action of cholecystokinin and cholinergic agents on calcium transport in isolated pancreatic acinar cells.

PubMed Central

Gardner, J D; Conlon, T P; Kleveman, H L; Adams, T D; Ondetti, M A

1975-01-01

COOH-terminal octapeptide of cholecystokinin (CCK-octapeptide) and the cholinergic agent carbamylcholine each produced a fourfold stimulation of calcium outflux in guinea pig isolated pancreatic acinar cells. Neither agent altered calcium influx. Stimulation of calcium outflux was rapid and specific, was abolished by reducing the incubation temperature to 4 degrees C, and was a saturable function of the secretagogue concentration. The concentrations of CCK-octapeptide and carbamylcholine that produced half-maximal stimulation of calcium outflux were 3.1 x 10(-10) M and 4.9 x 10(-5) M, respectively. The cholinergic antagonist antropine competitively inhibited carbamylcholine stimulation of calcium outflux but did not alter stimulation produced by CCK-octapeptide. Stimulation of calcium outflux by maximal concentrations of carbamycholine plus CCK-octapeptide was the same as that produced by a maximal concentration of either agent alone.Calcium outflux became refractory to stimulation by secretagogues, and incubation with either CCK-ostapeptide or carbamylcholine produced a refractoriness to both agents. The relative potencies with CCK and its related fragments stimulated calcium outflux were CCK-octapeptide greater than heptapeptide greater than CCK greater than hexapeptide = gastrin. Secretin, glucagon, and vasoactive intestinal peptide, at concentrations as high as 10(-5) M, failed to alter calcium outflux and did not affect stimulation by CCK-octapeptide or by carbamycholine. Images PMID:1150877

Technological properties of indigenous wine yeast strains isolated from wine production regions of Turkey.

PubMed

Bağder Elmacı, Simel; Özçelik, Filiz; Tokatlı, Mehmet; Çakır, İbrahim

2014-05-01

The purpose of this study was to evaluate the important technological and fermentative properties of wine yeast strains previously isolated from different wine producing regions of Turkey. The determination of the following important properties was made: growth at high temperatures; fermentative capability in the presence of high sugar concentration; fermentation rate; hydrogen sulfide production; killer activity; resistance to high ethanol and sulfur dioxide; foam production; and enzymatic profiles. Ten local wine yeast strains belonging to Saccharomyces, and one commercial active dry yeast as a reference strain were evaluated. Fermentation characteristics were evaluated in terms of kinetic parameters, including ethanol yield (YP/S), biomass yield (YX/S), theoretical ethanol yield (%), specific ethanol production rate (qp; g/gh), specific glucose uptake rate (qs; g/gh), and the substrate conversion (%). All tested strains were able to grow at 37 °C and to start fermentation at 30° Brix, and were resistant to high concentrations of sulfur dioxide. 60 % of the strains were weak H2S producers, while the others produced high levels. Foam production was high, and no strains had killer activity. Six of the tested strains had the ability to grow and ferment at concentrations of 14 % ethanol. Except for one strain, all fermented most of the media sugars at a high rate, producing 11.0-12.4 % (v/v) ethanol. Although all but one strain had suitable characteristics for wine production, they possessed poor activities of glycosidase, esterase and proteinase enzymes of oenological interest. Nine of the ten local yeast strains were selected for their good oenological properties and their suitability as a wine starter culture.

The Effect of Flow Distribution on the Concentration of NO Produced by Pulsed Arc Discharge

NASA Astrophysics Data System (ADS)

Hu, Hui; Bao, Bin; Wang, Heli; Liang, Haiyan; He, Junjia; He, Zhenghao; Li, Jin

2007-12-01

As a new method to cure acute respiratory distress syndrome (ARDS), high blood pressure and some illnesses related to the lung, NO has recently received more attention. Thermal plasmas produced by arc discharge can create medical NO, but the concentration of NO2 produced by arc discharge must be controlled simultaneously. This paper investigates the characteristics and regulations of NO production at different flow distribution by pulsed arc discharge in dry air with a special pulsed power. The experimental results show that the flow distribution has a considerable effect on the NO concentration, the stabilization of NO. The production of NO2 could be controlled and the ratio of NO2/NO was decreased to about 10% in the arc discharge. Therefore, the arc discharge could produce stable inhaled NO for medical treatment by changing the flow distribution.

Pharmacological and gene regulation properties point to the SlHAK5 K+ transporter as a system for high-affinity Cs+ uptake in tomato plants.

PubMed

Ródenas, Reyes; Nieves-Cordones, Manuel; Rivero, Rosa M; Martinez, Vicente; Rubio, Francisco

2018-04-01

Potassium (K + ) and cesium (Cs + ) are chemically similar but while K + is an essential nutrient, Cs + can be toxic for living organisms, plants included. Two different situations could lead to problems derived from the presence of Cs + in agricultural systems: (1) presence of Cs + at high concentrations that could produce toxic effects on plants, (2) presence of micromolar concentrations of radiocesium, which can be accumulated in the plant and affect animal and human health through the food chain. While K + uptake has been well described in tomato plants, information on molecular mechanisms involved in Cs + accumulation in this species is absent. Here, we show that in tomato plants, high concentrations of Cs + produce deficiency of K + but do not induce high-affinity K + uptake or the gene encoding the high-affinity K + transporter SlHAK5. At these concentrations, Cs + uptake takes place through a Ca 2+ -sensitive pathway, probably a non-selective cation channel. At micromolar concentrations, Cs + is accumulated by a high-affinity uptake system upregulated in K + -starved plants. This high-affinity Cs + uptake shares features with high-affinity K + uptake. It is sensitive to NH 4 + and insensitive to Ba 2+ and Ca 2+ and its presence parallels the pattern of SlHAK5 expression. Moreover, blockers of reactive oxygen species and ethylene action repress SlHAK5 and negatively regulate both high-affinity K + and Cs + uptake. Thus, we propose that SlHAK5 contributes to Cs + uptake from micromolar concentrations in tomato plants and can constitute a pathway for radiocesium transfer from contaminated areas to the food chain. © 2017 Scandinavian Plant Physiology Society.

Integration of alternative feedstreams for biomass treatment and utilization

DOEpatents

Hennessey, Susan Marie [Avondale, PA; Friend, Julie [Claymont, DE; Dunson, Jr., James B.; Tucker, III, Melvin P.; Elander, Richard T [Evergreen, CO; Hames, Bonnie [Westminster, CO

2011-03-22

The present invention provides a method for treating biomass composed of integrated feedstocks to produce fermentable sugars. One aspect of the methods described herein includes a pretreatment step wherein biomass is integrated with an alternative feedstream and the resulting integrated feedstock, at relatively high concentrations, is treated with a low concentration of ammonia relative to the dry weight of biomass. In another aspect, a high solids concentration of pretreated biomass is integrated with an alternative feedstream for saccharifiaction.

In vivo effects of environmental concentrations of produced water on the reproductive function of polar cod (Boreogadus saida).

PubMed

Geraudie, P; Nahrgang, J; Forget-Leray, J; Minier, C; Camus, L

2014-01-01

Offshore oil and gas drilling processes generate operational discharges such as produced water (PW), a complex mixture of seawater with polycyclic aromatic hydrocarbons (PAH) and alkylphenols (AP). Some of these compounds may interact with the endocrine system of marine organisms and alter reproductive functions. In this study, polar cod were exposed for up to 28 d to a mixture of PAH, alkylated PAH, and AP simulating the composition of North Sea PW, at low and high concentrations (1:2000 and 1:1000 dilution of the original concentrate, respectively). Potential adverse effects of PW on polar cod physiology were investigated through biomarkers of biotransformation (hepatic ethoxyresorufin O-deethylase [EROD] activity and bile PAH metabolites), endocrine disruption (plasma vitellogenin [VTG] levels and sex steroid concentrations), and gonad histology. Plasma sexual steroid levels in fish were not markedly affected by PW exposure, while higher plasma VTG concentrations were measured in females exposed to the high PW treatment for 7 and 28 d. In males exposed to the higher PW concentration, inhibition of spermatogenesis was observed after 28 d in addition to increase of melano-macrophage occurrence in testis. Females exposed to the high PW treatment for 21 d showed a significant increase of atresia incidence. Finally, a significant decrease in oocyte number was observed in high PW exposed female ovaries after 28 d of exposure.

Major and trace elements in organically or conventionally produced milk.

PubMed

Hermansen, John E; Badsberg, Jens H; Kristensen, Troels; Gundersen, Vagn

2005-08-01

A total of 480 samples of milk from 10 organically and 10 conventionally producing dairy farms in Denmark and covering 8 sampling periods over 1 year (triplicate samplings) were analysed for 45 trace elements and 6 major elements by high-resolution inductively coupled plasma mass spectrometry and inductively coupled plasma atomic emission spectrometry. Sampling, sample preparation, and analysis of the samples were performed under carefully controlled contamination-free conditions. The dairy cattle breeds were Danish-Holstein or Jersey. Sources of variance were quantified, and differences between production systems and breeds were tested. The major source of variation for most elements was week of sampling. Concentrations of Al, Cu, Fe, Mo, Rb, Se, and Zn were within published ranges. Concentrations of As, Cd, Cr, Mn and Pb were lower, and concentrations of Co and Sr were higher than published ranges. Compared with Holsteins, Jerseys produced milk with higher concentrations of Ba, Ca, Cu, Fe, Mg, Mn, Mo, P, Rh, and Zn and with a lower concentration of Bi. The organically produced milk, compared with conventionally produced milk, contained a significantly higher concentration of Mo (48 v. 37 ng/g) and a lower concentration of Ba (43 v. 62 ng/g), Eu (4 v. 7 ng/g), Mn (16 v. 20 ng/g) and Zn (4400 v. 5150 ng/g respectively). The investigation yielded typical concentrations for the following trace elements in milk, for which no or very few data are available: Ba, Bi, Ce, Cs, Eu, Ga, Gd, In, La, Nb, Nd, Pd, Pr, Rh, Sb, Sm, Tb, Te, Th, Ti, Tl, U, V, Y, and Zr.

Sensory Effects of Menthol and Nicotine in an E-Cigarette

PubMed Central

Rosbrook, Kathryn

2016-01-01

Introduction: Despite the longstanding use and popularity of menthol as a flavorant in tobacco products, its sensory interactions with inhaled nicotine have never been measured independently of the other irritants in tobacco smoke. We therefore measured the perception of menthol in an E-cigarette with the primary goal of assessing its analgesic effect on the sensory irritation produced by inhaled nicotine. Methods: Adult cigarette smokers sampled aerosolized E-liquids containing five different concentrations of nicotine with 0%, 0.5%, or 3.5% l-menthol, as well as two commercial menthol flavors with and without nicotine. For each of the E-liquids participants used a labeled magnitude scale to rate the Overall Sensation intensity, Coolness/Cold, and Irritation/Harshness they experienced, and a Labeled Hedonic Scale to indicate how much they liked/disliked the overall flavor. Results: The main findings were that (1) perceived Irritation/Harshness was unaffected by a low (0.5%) menthol concentration, whereas a high menthol concentration (3.5%) led to higher perceived Irritation/Harshness at low nicotine concentrations but to lower Irritation/Harshness at the highest nicotine concentration (24mg/ml); (2) a commercial Menthol–Mint flavor produced similar results; (3) nicotine tended to enhance rather than suppress sensations of Coolness/Cold; and (4) menthol tended to slightly increase liking independently of nicotine concentration. Conclusion: In addition to adding a sensation of coolness, menthol can reduce perceived airway irritation and harshness produced by inhalation when nicotine concentration is high, and contributes to the sensory impact of E-liquids when nicotine concentration is low. Implications: The evidence presented here indicates that menthol can potentially improve the appeal of E-cigarettes not only via its coolness and minty flavor, but also by reducing the harshness from high concentrations of nicotine. As the first direct demonstration of an analgesic effect of menthol on inhaled nicotine in humans, these data also have implications for the role of menthol flavors in other inhaled tobacco products. PMID:26783293

Annual cycle of dimethylsulfoniopropionate (DMSP) and dimethylsulfoxide (DMSO) related to phytoplankton succession in the Southern North Sea.

PubMed

Speeckaert, Gaëlle; Borges, Alberto V; Champenois, Willy; Royer, Colin; Gypens, Nathalie

2018-05-01

The influence of abiotic and biotic variables on the concentration of dimethyl sulfide (DMS), dimethylsulfoniopropionate (DMSP), and dimethylsulfoxide (DMSO), were investigated during an annual cycle in 2016 in the Belgian Coastal Zone (BCZ, North Sea). We reported strong seasonal variations in the concentration of these compounds linked to the phytoplankton succession with high DMS(P,O) producers (mainly Phaeocystis globosa) occurring in spring and low DMS(P,O) producers (various diatoms species) occurring in early spring and autumn. Spatial gradients of DMS and DMSP were related to those of phytoplankton biomass itself related to the inputs of nutrients from the Scheldt estuary. However, the use of a relationship with Chlorophyll-a (Chl-a) concentration is not sufficient to predict DMSP. Accounting for the phytoplankton composition, two different DMSP versus Chl-a correlations could be established, one for diatoms and another one for Phaeocystis colonies. We also reported high nearshore DMSO concentrations uncoupled to Chl-a and DMSP concentrations but linked to high suspended particulate matter (SPM) presumably coming from the Scheldt estuary as indicated by the positive relationship between annual average SPM and salinity. Copyright © 2017 Elsevier B.V. All rights reserved.

Color, bioactive compounds and morphological characteristics of encapsulated Asian pear juice powder during spray drying.

PubMed

Lee, Chang-Gon; Ahmed, Maruf; Jiang, Gui-Hun; Eun, Jong-Bang

2017-08-01

Encapsulated Asian pear juice powder was produced through spray drying using three maltodextrin levels (15, 20, and 25% w/v) and three inlet air temperatures (130, 150, and 170 °C). The impact of maltodextrin concentrations and inlet air temperatures on color, bioactive compounds, and morphological characteristics of encapsulated Asian pear juice powder were investigated. Maltodextrin concentrations and inlet air temperatures significantly influenced L * and b * values of encapsulated Asian pear juice powder. Increasing inlet air temperatures increased total phenolic content, whereas the vitamin C content decreased. Vitamin C content was strongly correlated with particle size, inlet air temperature, and maltodextrin concentration. ABTS + radical-scavenging activity was highly correlated with total phenol content while DPPH radical-scavenging activity was highly correlated with vitamin C content. Encapsulated powders made with higher inlet air temperature and higher maltodextrin concentration had lowest median particle diameter with a smoother, more regular and rounded outer surface than those of encapsulated powders produced with lower inlet air temperature and lower maltodextrin concentration. Therefore, the results demonstrate that high-quality encapsulated Asian pear juice powder could be manufactured by adding 15% (w/v) maltodextrin and spray-drying at 170 °C.

Cyanobacteria and Cyanotoxins: The Influence of Nitrogen versus Phosphorus

PubMed Central

Dolman, Andrew M.; Rücker, Jacqueline; Pick, Frances R.; Fastner, Jutta; Rohrlack, Thomas; Mischke, Ute; Wiedner, Claudia

2012-01-01

The importance of nitrogen (N) versus phosphorus (P) in explaining total cyanobacterial biovolume, the biovolume of specific cyanobacterial taxa, and the incidence of cyanotoxins was determined for 102 north German lakes, using methods to separate the effects of joint variation in N and P concentration from those of differential variation in N versus P. While the positive relationship between total cyanobacteria biovolume and P concentration disappeared at high P concentrations, cyanobacteria biovolume increased continually with N concentration, indicating potential N limitation in highly P enriched lakes. The biovolumes of all cyanobacterial taxa were higher in lakes with above average joint NP concentrations, although the relative biovolumes of some Nostocales were higher in less enriched lakes. Taxa were found to have diverse responses to differential N versus P concentration, and the differences between taxa were not consistent with the hypothesis that potentially N2-fixing Nostocales taxa would be favoured in low N relative to P conditions. In particular Aphanizomenon gracile and the subtropical invasive species Cylindrospermopsis raciborskii often reached their highest biovolumes in lakes with high nitrogen relative to phosphorus concentration. Concentrations of all cyanotoxin groups increased with increasing TP and TN, congruent with the biovolumes of their likely producers. Microcystin concentration was strongly correlated with the biovolume of Planktothrix agardhii but concentrations of anatoxin, cylindrospermopsin and paralytic shellfish poison were not strongly related to any individual taxa. Cyanobacteria should not be treated as a single group when considering the potential effects of changes in nutrient loading on phytoplankton community structure and neither should the N2-fixing Nostocales. This is of particular importance when considering the occurrence of cyanotoxins, as the two most abundant potentially toxin producing Nostocales in our study were found in lakes with high N relative to P enrichment. PMID:22719937

Cyanobacteria and cyanotoxins: the influence of nitrogen versus phosphorus.

PubMed

Dolman, Andrew M; Rücker, Jacqueline; Pick, Frances R; Fastner, Jutta; Rohrlack, Thomas; Mischke, Ute; Wiedner, Claudia

2012-01-01

The importance of nitrogen (N) versus phosphorus (P) in explaining total cyanobacterial biovolume, the biovolume of specific cyanobacterial taxa, and the incidence of cyanotoxins was determined for 102 north German lakes, using methods to separate the effects of joint variation in N and P concentration from those of differential variation in N versus P. While the positive relationship between total cyanobacteria biovolume and P concentration disappeared at high P concentrations, cyanobacteria biovolume increased continually with N concentration, indicating potential N limitation in highly P enriched lakes. The biovolumes of all cyanobacterial taxa were higher in lakes with above average joint NP concentrations, although the relative biovolumes of some Nostocales were higher in less enriched lakes. Taxa were found to have diverse responses to differential N versus P concentration, and the differences between taxa were not consistent with the hypothesis that potentially N(2)-fixing Nostocales taxa would be favoured in low N relative to P conditions. In particular Aphanizomenon gracile and the subtropical invasive species Cylindrospermopsis raciborskii often reached their highest biovolumes in lakes with high nitrogen relative to phosphorus concentration. Concentrations of all cyanotoxin groups increased with increasing TP and TN, congruent with the biovolumes of their likely producers. Microcystin concentration was strongly correlated with the biovolume of Planktothrix agardhii but concentrations of anatoxin, cylindrospermopsin and paralytic shellfish poison were not strongly related to any individual taxa. Cyanobacteria should not be treated as a single group when considering the potential effects of changes in nutrient loading on phytoplankton community structure and neither should the N(2)-fixing Nostocales. This is of particular importance when considering the occurrence of cyanotoxins, as the two most abundant potentially toxin producing Nostocales in our study were found in lakes with high N relative to P enrichment.

Fabrication of Concentrated Fish Oil Emulsions Using Dual-Channel Microfluidization: Impact of Droplet Concentration on Physical Properties and Lipid Oxidation.

PubMed

Liu, Fuguo; Zhu, Zhenbao; Ma, Cuicui; Luo, Xiang; Bai, Long; Decker, Eric Andrew; Gao, Yanxiang; McClements, David Julian

2016-12-21

Chemically unstable lipophilic bioactives, such as polyunsaturated lipids, often have to be encapsulated in emulsion-based delivery systems before they can be incorporated into foods, supplements, and pharmaceuticals. The objective of this study was to develop highly concentrated emulsion-based fish oil delivery systems using natural emulsifiers. Fish oil-in-water emulsions were fabricated using a highly efficient dual-channel high-pressure microfluidizer. The impact of oil concentration on the formation, physical properties, and oxidative stability of fish oil emulsions prepared using two natural emulsifiers (quillaja saponins and rhamnolipids) and one synthetic emulsifier (Tween-80) was examined. The mean droplet size, polydispersity, and apparent viscosity of the fish oil emulsions increased with increasing oil content. However, physically stable emulsions with high fish oil levels (30 or 40 wt %) could be produced using all three emulsifiers, with rhamnolipids giving the smallest droplet size (d < 160 nm). The stability of the emulsions to lipid oxidation increased as the oil content increased. The oxidative stability of the emulsions also depended on the nature of the emulsifier coating the lipid droplets, with the oxidative stability decreasing in the following order: rhamnolipids > saponins ≈ Tween-80. These results suggest that rhamnolipids may be particularly effective at producing emulsions containing high concentrations of ω-3 polyunsaturated fatty acids-rich fish oil.

Spiral pattern in a radial displacement involving a reaction-producing gel.

PubMed

Nagatsu, Yuichiro; Hayashi, Atsushi; Ban, Mitsumasa; Kato, Yoshihito; Tada, Yutaka

2008-08-01

We have shown experimentally that the pattern created by the displacement of a more viscous fluid by a less viscous one in a radial Hele-Shaw cell develops not radially but spirally when a more viscous sodium polyacrylate solution is displaced by a less viscous trivalent iron ion (Fe3+) solution with a sufficiently high concentration of Fe3+ . Another experiment revealed that an instantaneous chemical reaction takes place between the two fluids, and at high Fe3+ concentrations it produces a film of the gel at the contact plane. The gel film is proposed to be responsible for the spiral pattern.

Spiral pattern in a radial displacement involving a reaction-producing gel

NASA Astrophysics Data System (ADS)

Nagatsu, Yuichiro; Hayashi, Atsushi; Ban, Mitsumasa; Kato, Yoshihito; Tada, Yutaka

2008-08-01

We have shown experimentally that the pattern created by the displacement of a more viscous fluid by a less viscous one in a radial Hele-Shaw cell develops not radially but spirally when a more viscous sodium polyacrylate solution is displaced by a less viscous trivalent iron ion (Fe3+) solution with a sufficiently high concentration of Fe3+ . Another experiment revealed that an instantaneous chemical reaction takes place between the two fluids, and at high Fe3+ concentrations it produces a film of the gel at the contact plane. The gel film is proposed to be responsible for the spiral pattern.

Method of fabricating optical waveguides by ion implantation doping

DOEpatents

Appleton, B.R.; Ashley, P.R.; Buchal, C.J.

1987-03-24

A method for fabricating high-quality optical waveguides in optical quality oxide crystals by ion implantation doping and controlled epitaxial recrystallization is provided. Masked LiNbO/sub 3/ crystals are implanted with high concentrations of Ti dopant at ion energies of about 360 keV while maintaining the crystal near liquid nitrogen temperature. Ion implantation doping produces an amorphous, Ti-rich nonequilibrium phase in the implanted region. Subsequent thermal annealing in a water-saturated oxygen atmosphere at up to 1000/degree/C produces solid-phase epitaxial regrowth onto the crystalline substrate. A high-quality crystalline layer results which incorporates the Ti into the crystal structure at much higher concentrations than is possible by standard diffusion techniques, and this implanted region has excellent optical waveguiding properties.

The Effect of Initial Cell Concentration on Xylose Fermentation by Pichia stipitis

NASA Astrophysics Data System (ADS)

Agbogbo, Frank K.; Coward-Kelly, Guillermo; Torry-Smith, Mads; Wenger, Kevin; Jeffries, Thomas W.

Xylose was fermented using Pichia stipitis CBS 6054 at different initial cell concentrations. A high initial cell concentration increased the rate of xylose utilization, ethanol formation, and the ethanol yield. The highest ethanol concentration of 41.0 g/L and a yield of 0.38 g/g was obtained using an initial cell concentration of 6.5 g/L. Even though more xylitol was produced when the initial cell concentrations were high, cell density had no effect on the final ethanol yield. A two-parameter mathematical model was used to predict the cell population dynamics at the different initial cell concentrations. The model parameters, a and b correlate with the initial cell concentrations used with an R 2 of 0.99.

Operational multisensor sea ice concentration algorithm utilizing Sentinel-1 and AMSR2 data

NASA Astrophysics Data System (ADS)

Dinessen, Frode

2017-04-01

The Norwegian Ice Service provide ice charts of the European part of the Arctic every weekday. The charts are produced from a manually interpretation of satellite data where SAR (Synthetic Aperture Radar) data plays a central role because of its high spatial resolution and Independence of cloud cover. A new chart is produced every weekday and the charts are distributed through the CMEMS portal. After the launch of Sentinel-1A and B the number of available SAR data have significant increased making it difficult to utilize all the data in a manually process. This in combination with a user demand for a more frequent update of the ice conditions, also during the weekends, have made it important to focus the development on utilizing the high resolution Sentinel-1 data in an automatic sea ice concentration analysis. The algorithm developed here is based on a multi sensor approach using an optimal interpolation to combine sea ice concentration products derived from Sentinel-1 and passive microwave data from AMSR2. The Sentinel-1 data is classified with a Bayesian SAR classification algorithm using data in extra wide mode dual polarization (HH/HV) to separate ice and water in the full 40x40 meter spatial resolution. From the classification of ice/water the sea ice concentration is estimated by calculating amount of ice within an area of 1x1 km. The AMSR2 sea ice concentration are produced as part of the EUMETSAT Ocean and Sea Ice Satellite Application Facility (OSI SAF) project and utilize the 89 GHz channel to produce a concentration product with a 3km spatial resolution. Results from the automatic classification will be presented.

Glyphosate and AMPA contents in sediments produced by wind erosion of agricultural soils in Argentina

NASA Astrophysics Data System (ADS)

Aparicio, Virginia; Aimar, Silvia; De Gerónimo, Eduardo; Buschiazzo, Daniel; Mendez, Mariano; Costa, José Luis

2014-05-01

Wind erosion of soils is an important event in arid and semiarid regions of Argentina. The magnitude of wind erosion occurring under different management practices is relatively well known in this region but less information is available on the quality of the eroded material. Considering that the intensification of agriculture may increase the concentrations of substances in the eroded material, producing potential negative effects on the environment, we analyzed the amount of glyphosate and AMPA in sediments produced by wind erosion of agricultural soils of Argentina. Wind eroded materials were collected by means of BSNE samplers in two loess sites of the semiarid region of Argentina: Chaco and La Pampa. Samples were collected from 1 ha square fields at 13.5, 50 and 150 cm height. Results showed that at higher heights the concentrations of glyphosate and AMPA were mostly higher. The glyphosate concentration was more variable and higher in Chaco (0.66 to 313 µg kg-1) than in La Pampa (4.17 to 114 µg kg-1). These results may be due to the higher use of herbicides in Chaco, where the predominant crops are soybeans and corn, produced under no-tillage. Under these conditions the use of glyphosate for weeds control is a common practice. Conversely, AMPA concentrations were higher in La Pampa (13.1 to 101.3 µg kg-1) than in Chaco (1.3 to 83 µg kg-1). These preliminary results show high concentrations of glyphosate and AMPA in wind eroded materials of agricultural soils of Argentina. More research is needed to confirm these high concentrations in other conditions in order to detect the temporal and spatial distribution patterns of the herbicide.

Method for producing high carrier concentration p-Type transparent conducting oxides

DOEpatents

Li, Xiaonan; Yan, Yanfa; Coutts, Timothy J.; Gessert, Timothy A.; Dehart, Clay M.

2009-04-14

A method for producing transparent p-type conducting oxide films without co-doping plasma enhancement or high temperature comprising: a) introducing a dialkyl metal at ambient temperature and a saturated pressure in a carrier gas into a low pressure deposition chamber, and b) introducing NO alone or with an oxidizer into the chamber under an environment sufficient to produce a metal-rich condition to enable NO decomposition and atomic nitrogen incorporation into the formed transparent metal conducting oxide.

The estimation of occupational dose in 15 MV varian clinac iX room by Argon-41 as an activation product of photoneutron

NASA Astrophysics Data System (ADS)

Latifah, R.; Bunawas; Noor, J. A. E.

2018-03-01

Linear accelerator (linac) becomes the most commonly used treatment to damage and kill cancer cell. Photon and electron as the radiation beam are produced by accelerating electrons to very high energy. Neutrons are generated when incident high photon energy interacts with component of linac such as target, flattering filter and collimator via photoneutrons reaction. The neutrons can also produce activation of materials in treatment room to generate radioactive materials. We have estimated the concentration of Argon-41 as activated product from argon-40 in the linac room using foil activation. The results show that the Argon-41 concentration in linac room which is operated 15 MV for 1 treatment (1 minute) is 1440 Bq/m3. Accordingly that concentration, the occupational dose is 6.4 mSv per year.

Within-Mat Variability in Anatoxin-a and Homoanatoxin-a Production among Benthic Phormidium (Cyanobacteria) Strains

PubMed Central

Wood, Susanna A.; Smith, Francine M. J.; Heath, Mark W.; Palfroy, Thomas; Gaw, Sally; Young, Roger G.; Ryan, Ken G.

2012-01-01

Benthic Phormidium mats can contain high concentrations of the neurotoxins anatoxin-a and homoanatoxin-a. However, little is known about the co-occurrence of anatoxin-producing and non-anatoxin-producing strains within mats. There is also no data on variation in anatoxin content among toxic genotypes isolated from the same mat. In this study, 30 Phormidium strains were isolated from 1 cm2 sections of Phormidium-dominated mats collected from three different sites. Strains were grown to stationary phase and their anatoxin-a, homoanatoxin-a, dihydroanatoxin-a and dihydrohomoanatoxin-a concentrations determined using liquid chromatography-mass spectrometry. Each strain was characterized using morphological and molecular (16S rRNA gene sequences) techniques. Eighteen strains produced anatoxin-a, dihydroanatoxin-a or homoanatoxin-a. Strains isolated from each mat either all produced toxins, or were a mixture of anatoxin and non-anatoxin-producing genotypes. Based on morphology these genotypes could not be separated. The 16S rRNA gene sequence comparisons showed a difference of at least 17 nucleotides among anatoxin and non-anatoxin-producing strains and these formed two separate sub-clades during phylogenetic analysis. The total anatoxin concentration among toxic strains varied from 2.21 to 211.88 mg kg−1 (freeze dried weight), representing a 100 fold variation in toxin content. These data indicate that both the relative abundance of anatoxin and non-anatoxin-producing genotypes, and variations in anatoxin producing capability, can influence the overall toxin concentration of benthic Phormidium mat samples. PMID:23162704

TPK Sarimukti, Cipatat, West Bandung compost toxicity test using Allium test

NASA Astrophysics Data System (ADS)

Wardini, Trimurti Hesti; Notodarmojo, Peni Astrini

2015-09-01

TPK Sarimukti, Cipatat, West Bandung produced 2 kinds of compost from traditional market waste, liquid and solid compost. The aim of this research is to evaluate toxicity of compost produced in TPK Sarimukti using shallots (Allium cepa). Tests carried out by treated shallots with liquid compost (2,5%, 5%, 10% and 12,5% (w/v)) or solid compost (25%, 50%, 75% and 100% (w/v)) for 48 hours. Results showed reduced root growth rate and mitotic index (MI) in accordance with increased concentrations of compost. Sub lethal concentrations are liquid compost 5% and 10% and solid compost 75%. Lethal concentrations are liquid compost 12,5 % and solid compost 100%. Micronuclei (MN) increased with increase in liquid compost concentration. MN found at very high frequencies in highest solid compost concentration (100%), but very low at lower concentrations. Cells with binuclei and cell necrosis increased with increasing concentrations of given compost. Nuclear anomalies (NA) found in high frequency in 75% and 100% solid compost. Based on research, we can conclude that liquid compost is more toxic because it can reduce MI and root growth rate at lower concentrations than solid compost. Both types of compost have genotoxic properties because it can induce chromosome aberration (CA), MN, binuclei and NA formation.

TPK Sarimukti, Cipatat, West Bandung compost toxicity test using Allium test

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wardini, Trimurti Hesti; Notodarmojo, Peni Astrini

TPK Sarimukti, Cipatat, West Bandung produced 2 kinds of compost from traditional market waste, liquid and solid compost. The aim of this research is to evaluate toxicity of compost produced in TPK Sarimukti using shallots (Allium cepa). Tests carried out by treated shallots with liquid compost (2,5%, 5%, 10% and 12,5% (w/v)) or solid compost (25%, 50%, 75% and 100% (w/v)) for 48 hours. Results showed reduced root growth rate and mitotic index (MI) in accordance with increased concentrations of compost. Sub lethal concentrations are liquid compost 5% and 10% and solid compost 75%. Lethal concentrations are liquid compost 12,5more » % and solid compost 100%. Micronuclei (MN) increased with increase in liquid compost concentration. MN found at very high frequencies in highest solid compost concentration (100%), but very low at lower concentrations. Cells with binuclei and cell necrosis increased with increasing concentrations of given compost. Nuclear anomalies (NA) found in high frequency in 75% and 100% solid compost. Based on research, we can conclude that liquid compost is more toxic because it can reduce MI and root growth rate at lower concentrations than solid compost. Both types of compost have genotoxic properties because it can induce chromosome aberration (CA), MN, binuclei and NA formation.« less

Microbial mats as a biological treatment approach for saline wastewaters: the case of produced water from hydraulic fracturing.

PubMed

Akyon, Benay; Stachler, Elyse; Wei, Na; Bibby, Kyle

2015-05-19

Treatment of produced water, i.e. wastewater from hydraulic fracturing, for reuse or final disposal is challenged by both high salinity and the presence of organic compounds. Organic compounds in produced water may foul physical-chemical treatment processes or support microbial corrosion, fouling, and sulfide release. Biological approaches have potential applications in produced water treatment, including reducing fouling of physical-chemical treatment processes and decreasing biological activity during produced water holding; however, conventional activated sludge treatments are intolerant of high salinity. In this study, a biofilm treatment approach using constructed microbial mats was evaluated for biodegradation performance, microbial community structure, and metabolic potential in both simulated and real produced water. Results demonstrated that engineered microbial mats are active at total dissolved solids (TDS) concentrations up to at least 100,000 mg/L, and experiments in real produced water showed a biodegradation capacity of 1.45 mg COD/gramwet-day at a TDS concentration of 91,351 mg/L. Additionally, microbial community and metagenomic analyses revealed an adaptive microbial community that shifted based upon the sample being treated and has the metabolic potential to degrade a wide array of contaminants, suggesting the potential of this approach to treat produced waters with varying composition.

Modelling bio-electrosynthesis in a reverse microbial fuel cell to produce acetate from CO2 and H2O.

PubMed

Kazemi, M; Biria, D; Rismani-Yazdi, H

2015-05-21

Bio-electrosynthesis is one of the significant developments in reverse microbial fuel cell technology which is potentially capable of creating organic compounds by combining CO2 with H2O. Accordingly, the main objective in the current study was to present a model of microbial electrosynthesis for producing organic compounds (acetate) based on direct conduction of electrons in biofilms. The proposed model enjoys a high degree of rigor because it can predict variations in the substrate concentration, electrical potential, current density and the thickness of the biofilm. Additionally, coulombic efficiency was investigated as a function of substrate concentration and cathode potential. For a system containing CO2 as the substrate and Sporomusa ovata as the biofilm forming microorganism, an increase in the substrate concentration at a constant potential can lead to a decrease in coulombic efficiency as well as an increase in current density and biofilm thickness. On the other hand, an increase in the surface cathodic voltage at a constant substrate concentration may result in an increase in the coulombic efficiency and a decrease in the current density. The maximum coulombic efficiency was revealed to be 75% at a substrate concentration of 0.025 mmol cm(-3) and 55% at a surface cathodic voltage of -0.3 V producing a high range of acetate production by creating an optimal state in the concentration and potential intervals. Finally, the validity of the model was verified by comparing the obtained results with related experimental findings.

The role of nitrogen and phosphorus in regulating Phormidium sp. (cyanobacteria) growth and anatoxin production.

PubMed

Heath, Mark; Wood, Susie A; Young, Roger G; Ryan, Ken G

2016-03-01

Benthic proliferations of the cyanobacteria Phormidium can cover many kilometres of riverbed. Phormidium can produce neurotoxic anatoxins and ingestion of benthic mats has resulted in numerous animal poisonings in the last decade. Despite this, there is a poor understanding of the environmental factors regulating growth and anatoxin production. In this study, the effects of nitrogen and phosphorus on the growth of two Phormidium strains (anatoxin-producing and non-anatoxin-producing) were examined in batch monocultures. Cell concentrations were significantly reduced under reduced nitrogen (ca. <0.100 mM) and phosphorus conditions (ca. <0.003 mM). Cell concentrations and maximum growth rates were higher for the non-anatoxin-producing strain in all treatments, suggesting there may be an energetic cost to toxin production. Cellular anatoxin concentrations were lowest (169 fg cell(-1)) under the high-nitrogen and high-phosphorus treatment. This supports the growth-differentiation balance hypothesis that suggests actively dividing and expanding cells are less likely to produce secondary-metabolites. Anatoxin quota was highest (>407 fg cell(-1)) in the reduced phosphorus treatments, possibly suggesting that it is produced as a stress response to growth limiting conditions. In all treatments there was a 4-5-fold increase in anatoxin quota in the lag growth phase, possibly indicating it may provide a physiological benefit during initial substrate colonization. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Novel inorganic nanomaterials generated with highly concentrated sunlight

NASA Astrophysics Data System (ADS)

Gordon, Jeffrey M.; Katz, Eugene A.; Feuermann, Daniel; Albu-Yaron, Ana; Levy, Moshe; Tenne, Reshef

2008-08-01

Reactors driven by highly concentrated sunlight can create conditions well suited to the synthesis of inorganic nanomaterials. We report the experimental realization of a broad range of closed-cage (fullerene-like) nanostructures, nanotubes and/or nanowires for MoS2, SiO2 and Si, achieved via solar ablation. The solar technique generates the strong temperature and radiative gradients - in addition to the extensive high-temperature annealing environment - conducive to producing such nanostructures. The identity of the nanostructures was established with TEM, HRTEM and EDS. The fullerene-like and nanotube MoS2 configurations achieved fundamentally minimum sizes predicted by molecular structural theory. Furthermore, our experiments represent the first time SiO2 nanofibers and nanospheres have been produced purely from quartz. The solar route is far less energy intensive than laser ablation and other high-temperature chemical reactors, simpler and less costly.

High-throughput PBPK and Microdosimetry: Cell-level Exposures in a Virtual Tissue Context (WC9)

EPA Science Inventory

Toxicokinetic (TK) models can determine whether chemical exposures produce potentially hazardous tissue concentrations. Tissue microdosimetry TK models relate whole-body chemical exposures to cell-scale concentrations. As a proof of concept, we approximated the micro-anatomic arc...

Natural attenuation of chlorinated hydrocarbons in a freshwater wetland

USGS Publications Warehouse

Lora, Michelle M.; Olsen, Lisa D.; Smith, Barrett L.; Alleman, Bruce C.; Leeson, Andrea

1997-01-01

Natural attenuation of chlorinated volatile organic compounds (VOC's) occurs as ground water discharges from a sand aquifer to a freshwater wetland at Aberdeen Proving Ground, Md. Field and laboratory results indicate that biotransformation in the anaerobic wetland sediments is an important attenuation process. Relatively high concentrations of the parent compounds trichloroethylene (TCE) and 1,1,2,2-tetrachloroethane (PCA) and low or undetectable concentrations of daughter products were measured in the aquifer. In contrast, relatively high concentrations of the daughter products cis- and trans-1,2-dichloroethylene (12DCE); vinyl chloride (VC); 1,1,2-trichloroethane (112TCA); and 1,2-dichloroethane (12DCA) were measured in ground water in the wetland sediments, although total VOC concentrations decreased upward from about 1 mu mol/L (micromoles per liter) at the base of the wetland sediments to less than 0.2 near the surface. Microcosm experiments showed that 12DCE and VC are produced from anaerobic degradation of both TCE and PCA; PCA degradation also produced 112TCA and 12DCA.

Enhanced biosynthesis of chiral phenyllactic acid from L-phenylalanine through a new whole-cell biocatalyst.

PubMed

Zheng, Zhaojuan; Xia, Meijuan; Fang, Xuchao; Jiang, Ting; Ouyang, Jia

2018-06-22

Phenyllactic acid (PLA) is a high-value compound, which was usually produced by lactic acid bacteria (LAB) as biocatalysts and glucose or phenylpyruvic acid (PPA) as starting materials for PLA synthesis in previous studies. However, the PLA produced using LAB is a racemic mixture. Besides, both glucose and PPA were unsatisfactory substrates, as the former could not produce high concentrations of PLA while the latter is not a renewable and green substrate. To overcome these drawbacks, in this study, a new biotransformation process was developed for chiral PLA production from L-phenylalanine via the intermediate PPA using recombinant Escherichia coli co-expressing L-amino acid deaminase, NAD-dependent L-lactate dehydrogenase or NAD-dependent D-lactate dehydrogenase, and formate dehydrogenase. After optimization, the recombinant E. coli produced L- and D-PLA at concentrations of 59.9 and 60.3 mM in 6 h, respectively. Hence, this process provides an effective and promising alternative method for chiral PLA production.

Formation of secondary aerosols from the ozonolysis of styrene: Effect of SO2 and H2O

NASA Astrophysics Data System (ADS)

Díaz-de-Mera, Yolanda; Aranda, Alfonso; Martínez, Ernesto; Rodríguez, Ana Angustias; Rodríguez, Diana; Rodríguez, Ana

2017-12-01

In this work we report the study of the ozonolysis of styrene and the reaction conditions leading to the formation of secondary aerosols. The reactions have been carried out in a Teflon chamber filled with synthetic air mixtures at atmospheric pressure and room temperature. We have found that the ozonolysis of styrene in the presence of low concentrations of SO2 readily produces new particles under concentrations of reactants lower than those required in experiments in the absence of SO2. Thus, nucleation events occur at concentrations around (5.6 ± 1.7) × 108molecule cm-3 (errors are 2σ±20%) and SO2 is consumed during the experiments. The reaction of the Criegee intermediates with SO2 to produce SO3 and then H2SO4 may explain (together with OH reactions' contribution) the high capacity of styrene to produce particulate matter in polluted atmospheres. The formation of secondary aerosols in the smog chamber is inhibited under high H2O concentrations. So, the potential formation of secondary aerosols under atmospheric conditions depends on the concentration of SO2 and relative humidity, with a water to SO2 rate constants ratio kH2O/kSO2 = (2.8 ± 0.7) × 10-5 (errors are 2σ±20%).

Method of fabricating optical waveguides by ion implantation doping

DOEpatents

Appleton, Bill R.; Ashley, Paul R.; Buchal, Christopher J.

1989-01-01

A method for fabricating high-quality optical waveguides in optical quality oxide crystals by ion implantation doping and controlled epitaxial recrystallization is provided. Masked LiNbO.sub.3 crystals are implanted with high concentrations of Ti dopant at ion energies of about 350 keV while maintaining the crystal near liquid nitrogen temperature. Ion implantation doping produces an amorphous, Ti-rich nonequilibrium phase in the implanted region. Subsequent thermal annealing in a water-saturated oxygen atmosphere at up to 1000.degree. C. produces solid-phase epitaxial regrowth onto the crystalline substrate. A high-quality single crystalline layer results which incorporates the Ti into the crystal structure at much higher concentrations than is possible by standard diffusion techniques, and this implanted region has excellent optical waveguides properties.

Increasing Stabilized Performance Of Amorphous Silicon Based Devices Produced By Highly Hydrogen Diluted Lower Temperature Plasma Deposition.

DOEpatents

Li, Yaun-Min; Bennett, Murray S.; Yang, Liyou

1999-08-24

High quality, stable photovoltaic and electronic amorphous silicon devices which effectively resist light-induced degradation and current-induced degradation, are produced by a special plasma deposition process. Powerful, efficient single and multi-junction solar cells with high open circuit voltages and fill factors and with wider bandgaps, can be economically fabricated by the special plasma deposition process. The preferred process includes relatively low temperature, high pressure, glow discharge of silane in the presence of a high concentration of hydrogen gas.

Increased Stabilized Performance Of Amorphous Silicon Based Devices Produced By Highly Hydrogen Diluted Lower Temperature Plasma Deposition.

DOEpatents

Li, Yaun-Min; Bennett, Murray S.; Yang, Liyou

1997-07-08

High quality, stable photovoltaic and electronic amorphous silicon devices which effectively resist light-induced degradation and current-induced degradation, are produced by a special plasma deposition process. Powerful, efficient single and multi-junction solar cells with high open circuit voltages and fill factors and with wider bandgaps, can be economically fabricated by the special plasma deposition process. The preferred process includes relatively low temperature, high pressure, glow discharge of silane in the presence of a high concentration of hydrogen gas.

A new chemical tool for absinthe producers, quantification of α/β-thujone and the bitter components in Artemisia absinthium.

PubMed

Bach, Benoit; Cleroux, Marilyn; Saillen, Mayra; Schönenberger, Patrik; Burgos, Stephane; Ducruet, Julien; Vallat, Armelle

2016-12-15

The concentrations of α/β-thujone and the bitter components of Artemisia absinthium were quantified from alcoholic wormwood extracts during four phenological stages of their harvest period. A solid-phase micro-extraction method coupled to gas chromatography-mass spectrometry was used to determine the concentration of the two isomeric forms of thujone. In parallel, the combination of ultra-high pressure liquid chromatography and high resolution mass spectrometry allowed to quantify the compounds absinthin, artemisetin and dihydro-epi-deoxyarteannuin B. This present study aimed at helping absinthe producers to determine the best harvesting period. Copyright © 2016 Elsevier Ltd. All rights reserved.

Large inter-individual variation in isoflavone plasma concentration limits use of isoflavone intake data for risk assessment

PubMed Central

van der Velpen, V; Hollman, P C; van Nielen, M; Schouten, E G; Mensink, M; van't Veer, P; Geelen, A

2014-01-01

Background/objectives: Isoflavones are present in soy foods and soy-based supplements. Despite low plasma isoflavone concentrations in the general Western population, concentrations in supplement users exceed those suggested to be beneficial for health in Asian populations, raising concerns for adverse effects. To aid risk assessment, quantification of the relation between isoflavone intake and plasma concentrations is essential. Subjects/methods: Plasma samples were collected from postmenopausal women in three placebo-controlled crossover studies with 8-week periods for supplements (two studies, ~100 mg isoflavones/day, n=88) or 4-week periods for soy foods (one study, ~48 mg isoflavones/day, n=15). Plasma isoflavone concentrations (daidzein, equol, genistein and glycitein) were quantified using high-performance liquid chromatography and electrochemical detection. The association between plasma concentrations and isoflavone intake, equol producer status, intake–producer interaction and background dietary intake was assessed based on the assumption of a log-linear relation. Results: Median plasma total isoflavone concentrations after the soy food and supplement interventions were respectively 2.16 and 3.47 μmol/l for equol producers and 1.30 and 2.39 μmol/l for non-producers. Regression analysis showed that doubling isoflavone intake increased plasma concentrations by 55–62% (±s.e. 1–2%, R2>0.87) for daidzein, genistein, equol (only for producers) and total isoflavones; for glycitein the association was weaker (15±1%, R2=0.48). Adjustments for energy, carbohydrate and fat intake did not affect these estimates. Inter-individual variation, estimated based on repeated measures in one of the studies, was 30–96%. Conclusions: Although the relation between isoflavone intake and plasma concentrations was adequately quantified, the use of isoflavone intake data for risk assessment needs caution due to large inter-individual variation in plasma concentrations. PMID:24939433

Biorefinery of sweet sorghum stem.

PubMed

Yu, Jianliang; Zhang, Tao; Zhong, Jing; Zhang, Xu; Tan, Tianwei

2012-01-01

Sweet sorghum has been considered as a viable energy crop for alcohol fuel production. This review discloses a novel approach for the biorefining of sweet sorghum stem to produce multiple valuable products, such as ethanol, butanol and wood plastic composites. Sweet sorghum stem has a high concentration of soluble sugars in its juice, which can be fermented to produce ethanol by Saccharomyces cerevisiae. In order to obtain high ethanol yield and fermentation rates, concentrated juice with an initial total sugar concentration of 300gL(-1) was fermented. The maximum ethanol concentration after 54h reached 140gL(-1) with a yield of 0.49g ethanol per g consumed sugar, which is 97% of the theoretical value. Sweet sorghum bagasse, obtained from juice squeezing, was pretreated by acetic acid to hydrolyze 80-90% of the contained hemicelluloses. Using this hydrolysate as raw material (total sugar 55gL(-1)), 19.21gL(-1) total solvent (butanol 9.34g, ethanol 2.5g, and acetone 7.36g) was produced by Clostridium acetobutylicum. The residual bagasse after pretreatment was extruded with PLA in a twin-screw extruder to produce a final product having a PLA: fiber ratio of 2:1, a tensile strength of 49.5M and a flexible strength of 65MPa. This product has potential use for applications where truly biodegradable materials are required. This strategy for sustainability is crucial for the industrialization of biofuels from sweet sorghum. Copyright © 2012. Published by Elsevier Inc.

Air ion mobility spectra and concentrations upwind and downwind of overhead AC high voltage power lines

NASA Astrophysics Data System (ADS)

Wright, Matthew D.; Buckley, Alison J.; Matthews, James C.; Shallcross, Dudley E.; Henshaw, Denis L.

2014-10-01

Corona ions produced by high-voltage power lines (HVPLs) can alter the nearby electrical environment, potentially increasing aerosol charge levels downwind. However, there is a lack of knowledge concerning the concentration and mobility of ions from AC HVPLs and their dispersion away from the line. We present ion concentration and mobility measurements made near AC HVPLs in South-West England. Examples of typical mobility spectra are shown highlighting features commonly observed. Corona was observed during 33 of 46 measurements, at 9 of 11 sites, with positive or ‘bipolar' (both polarities) ion production commonly seen. Ion production usually increases atmospheric concentrations by only a modest amount, but extreme cases can enhance concentration by an order of magnitude or more. A polarity imbalance is required to increase aerosol charge via ion attachment; this was observed on 15 of 24 days when positive corona was observed, but was not seen for negative ions. Ion mobility was higher downwind compared with upwind for both ion polarities, but the increase was not statistically significant. Future work should focus on identifying and characterising ‘heavy-producing' HVPLs, and obtaining results in conditions which may favour negative ion production e.g. high humidity, inclement weather or during nighttime.

Characterization and treatment of dissolved organic matter from oilfield produced waters.

PubMed

Wang, Xiaojing; Goual, Lamia; Colberg, Patricia J S

2012-05-30

Dissolved organic matter (DOM) has been studied intensively in streams, lakes and oceans due to its role in the global carbon cycle and because it is a precursor of carcinogenic disinfection by-products in drinking water; however, relatively little research has been conducted on DOM in oilfield produced waters. In this study, recovery of DOM from two oilfield produced waters was relatively low (~34%), possibly due to the presence of high concentrations of volatile organic compounds (VOCs). A van Krevelen diagram of the extracted DOM suggested the presence of high concentrations of lipids, lignin, and proteins, but low concentrations of condensed hydrocarbons. Most of the compounds in the oilfield DOM contained sulfur in their structures. Fourier transform infrared (FTIR) spectra indicated the presence of methyl groups, amides, carboxylic acids, and aromatic compounds, which is in agreement with results of Fourier transform ion cyclotron resonance (FT-ICR) analysis. Qualitatively, DOM in oilfield produced waters is similar to that reported in oceans and freshwater, except that it contains much more sulfur and is less aromatic. Treatment studies conducted in a fluidized bed reactor suggested that volatilization of organics may be a more important mechanism of DOM removal than microbial degradation. Copyright © 2012 Elsevier B.V. All rights reserved.

A proteinaceous organic matrix regulates carbonate mineral production in the marine teleost intestine

PubMed Central

Schauer, Kevin L.; LeMoine, Christophe M. R.; Pelin, Adrian; Corradi, Nicolas; Warren, Wesley C.; Grosell, Martin

2016-01-01

Marine teleost fish produce CaCO3 in their intestine as part of their osmoregulatory strategy. This precipitation is critical for rehydration and survival of the largest vertebrate group on earth, yet the molecular mechanisms that regulate this reaction are unknown. Here, we isolate and characterize an organic matrix associated with the intestinal precipitates produced by Gulf toadfish (Opsanus beta). Toadfish precipitates were purified using two different methods, and the associated organic matrix was extracted. Greater than 150 proteins were identified in the isolated matrix by mass spectrometry and subsequent database searching using an O. beta transcriptomic sequence library produced here. Many of the identified proteins were enriched in the matrix compared to the intestinal fluid, and three showed no substantial homology to any previously characterized protein in the NCBI database. To test the functionality of the isolated matrix, a micro-modified in vitro calcification assay was designed, which revealed that low concentrations of isolated matrix substantially promoted CaCO3 production, where high concentrations showed an inhibitory effect. High concentrations of matrix also decreased the incorporation of magnesium into the forming mineral, potentially providing an explanation for the variability in magnesium content observed in precipitates produced by different fish species. PMID:27694946

Portable method of measuring gaseous acetone concentrations.

PubMed

Worrall, Adam D; Bernstein, Jonathan A; Angelopoulos, Anastasios P

2013-08-15

Measurement of acetone in human breath samples has been previously shown to provide significant non-invasive diagnostic insight into the control of a patient's diabetic condition. In patients with diabetes mellitus, the body produces excess amounts of ketones such as acetone, which are then exhaled during respiration. Using various breath analysis methods has allowed for the accurate determination of acetone concentrations in exhaled breath. However, many of these methods require instrumentation and pre-concentration steps not suitable for point-of-care use. We have found that by immobilizing resorcinol reagent into a perfluorosulfonic acid polymer membrane, a controlled organic synthesis reaction occurs with acetone in a dry carrier gas. The immobilized, highly selective product of this reaction (a flavan) is found to produce a visible spectrum color change which could measure acetone concentrations to less than ppm. We here demonstrate how this approach can be used to produce a portable optical sensing device for real-time, non-invasive acetone analysis. Copyright © 2013 Elsevier B.V. All rights reserved.

Effects of cholera toxin and isobutylmethylxanthine on growth of human fibroblasts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Espinoza, B.; Wharton, W.

1986-08-01

Cholera toxin produced a dose-dependent decrease in the restimulation of G0/G1 traverse in density-arrested human fibroblasts but did not inhibit the stimulation of cells arrested in G0 after serum starvation at low density. In addition, cholera toxin did not inhibit the proliferation of sparse logarithmically growing human fibroblasts, even when low concentrations of the phosphodiesterase inhibitor isobutylmethylxanthine (IBMX) were also present. However, the final density to which sparse cells grew was limited by cholera toxin, when added either alone or together with low concentrations of IBMX. In contrast, high concentrations of the phosphodiesterase inhibitor alone produced a profound inhibition inmore » the growth of sparse human fibrobasts. IBMX produced an inhibition both in the G1 and in the G2 phases of the cell cycle by a mechanism(s) that was not related to the magnitude of the increases in adenosine 3,5-cyclic monophosphate concentrations.« less

Discrimination of fluoride and phosphate contamination in central Florida for analyses of environmental effects

NASA Technical Reports Server (NTRS)

Coker, A. E.; Marshall, R.; Thomson, F.

1972-01-01

A study was made of the spatial registration of fluoride and phosphate pollution parameters in central Florida by utilizing remote sensing techniques. Multispectral remote sensing data were collected over the area and processed to produce multispectral recognition maps. These processed data were used to map land areas and waters containing concentrations of fluoride and phosphate. Maps showing distribution of affected and unaffected vegetation were produced. In addition, the multispectral data were processed by single band radiometric slicing to produce radiometric maps used to delineate areas of high ultraviolet radiance, which indicates high fluoride concentrations. The multispectral parameter maps and radiometric maps in combination showed distinctive patterns, which are correlated with areas known to be affected by fluoride and phosphate contamination. These remote sensing techniques have the potential for regional use to assess the environmental impact of fluoride and phosphate wastes in central Florida.

Mycotoxin production by indoor molds.

PubMed

Fog Nielsen, Kristian

2003-07-01

Fungal growth in buildings starts at a water activity (a(w)) near 0.8, but significant quantities of mycotoxins are not produced unless a(w) reaches 0.95. Stachybotrys generates particularly high quantities of many chemically distinct metabolites in water-damaged buildings. These metabolites are carried by spores, and can be detected in air samples at high spore concentrations. Very little attention has been paid to major metabolites of Stachybotrys called spirocyclic drimanes, and the precise structures of the most abundant of these compounds are unknown. Species of Aspergillus and Penicillium prevalent in the indoor environment produce relatively low concentrations of mycotoxins, with the exception of sterigmatocystins that can represent up to 1% of the biomass of A. versicolor at a(w)'s close to 1. The worst-case scenario for homeowners is produced by consecutive episodes of water damage that promote fungal growth and mycotoxin synthesis, followed by drier conditions that facilitate the liberation of spores and hyphal fragments.

Carbon Concentration and Carbon-to-Nitrogen Ratio Influence Submerged-Culture Conidiation by the Potential Bioherbicide Colletotrichum truncatum NRRL 13737

PubMed Central

Jackson, Mark A.; Bothast, Rodney J.

1990-01-01

We assessed the influence of various carbon concentrations and carbon-to-nitrogen (C:N) ratios on Colletotrichum truncatum NRRL 13737 conidium formation in submerged cultures grown in a basal salts medium containing various amounts of glucose and Casamino Acids. Under the nutritional conditions tested, the highest conidium concentrations were produced in media with carbon concentrations of 4.0 to 15.3 g/liter. High carbon concentrations (20.4 to 40.8 g/liter) inhibited sporulation and enhanced the formation of microsclerotiumlike hyphal masses. At all the carbon concentrations tested, a culture grown in a medium with a C:N ratio of 15:1 produced more conidia than cultures grown in media with C:N ratios of 40:1 or 5:1. While glucose exhaustion was often coincident with conidium formation, cultures containing residual glucose sporulated and those with high carbon concentrations (>25 g/liter) exhausted glucose without sporulation. Nitrogen source studies showed that the levels of C. truncatum NRRL 13737 conidiation were similar for all protein hydrolysates tested. Reduced conidiation occurred when amino acid and inorganic nitrogen sources were used. Of the nine carbon sources evaluated, acetate as the sole carbon source resulted in the lowest level of sporulation. Images PMID:16348348

Estimation of time-variable fast flow path chemical concentrations for application in tracer-based hydrograph separation analyses

USGS Publications Warehouse

Kronholm, Scott C.; Capel, Paul D.

2016-01-01

Mixing models are a commonly used method for hydrograph separation, but can be hindered by the subjective choice of the end-member tracer concentrations. This work tests a new variant of mixing model that uses high-frequency measures of two tracers and streamflow to separate total streamflow into water from slowflow and fastflow sources. The ratio between the concentrations of the two tracers is used to create a time-variable estimate of the concentration of each tracer in the fastflow end-member. Multiple synthetic data sets, and data from two hydrologically diverse streams, are used to test the performance and limitations of the new model (two-tracer ratio-based mixing model: TRaMM). When applied to the synthetic streams under many different scenarios, the TRaMM produces results that were reasonable approximations of the actual values of fastflow discharge (±0.1% of maximum fastflow) and fastflow tracer concentrations (±9.5% and ±16% of maximum fastflow nitrate concentration and specific conductance, respectively). With real stream data, the TRaMM produces high-frequency estimates of slowflow and fastflow discharge that align with expectations for each stream based on their respective hydrologic settings. The use of two tracers with the TRaMM provides an innovative and objective approach for estimating high-frequency fastflow concentrations and contributions of fastflow water to the stream. This provides useful information for tracking chemical movement to streams and allows for better selection and implementation of water quality management strategies.

A Burkholderia sacchari cell factory: production of poly-3-hydroxybutyrate, xylitol and xylonic acid from xylose-rich sugar mixtures.

PubMed

Raposo, Rodrigo S; de Almeida, M Catarina M D; de Oliveira, M da Conceição M A; da Fonseca, M Manuela; Cesário, M Teresa

2017-01-25

Efficient production of poly-3-hydroxybutyrate (P(3HB)) based on glucose-xylose mixtures simulating different types of lignocellulosic hydrolysate (LCH) was addressed using Burkholderia sacchari, a wild strain capable of metabolizing both sugars and producing P(3HB). Carbon catabolite repression was avoided by maintaining glucose concentration below 10g/L. Xylose concentrations above 30g/L were inhibitory for growth and production. In fed-batch cultivations, pulse size and feed addition rate were controlled in order to reach high productivities and efficient sugar consumptions. High xylose uptake and P(3HB) productivity were attained with glucose-rich mixtures (glucose/xylose ratio in the feed=1.5w/w) using high feeding rates, while with xylose-richer feeds (glucose/xylose=0.8w/w), a lower feeding rate is a robust strategy to avoid xylose build-up in the medium. Xylitol production was observed with xylose concentrations in the medium above 30-40g/L. With sugar mixtures featuring even lower glucose/xylose ratios, i.e. xylose-richer feeds (glucose/xylose=0.5), xylonic acid (a second byproduct) was produced. This is the first report of the ability of Burkholderia sacchari to produce both xylitol and xylonic acid. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of human chorionic gonadotropin on luteal function and reproductive performance of high-producing lactating Holstein dairy cows.

PubMed

Santos, J E; Thatcher, W W; Pool, L; Overton, M W

2001-11-01

The objectives were to evaluate effects of human chorionic gonadotropin (hCG) (3,300 IU i.m.) administered on d 5 after AI on CL number, plasma progesterone concentration, conception rate, and pregnancy loss in high-producing dairy cows. Following the synchronization of estrus and AI, 406 cows were injected with either hCG or saline on d 5 after AI in a randomized complete block design. Blood sampling and ovarian ultrasonography were conducted once between d 11 and 16 after AI. Pregnancy diagnoses were performed on d 28 by ultrasonography and on d 45 and 90 after AI by rectal palpation. Treatment with hCG on d 5 resulted in 86.2% of the cows with more than one CL compared with 23.2% in controls. Plasma progesterone concentrations were increased by 5.0 ng/mL in hCG-treated cows. The presence of more than one CL increased progesterone concentration in hCG-treated cows but not in controls. Conception rates were higher for hCG-treated cows on d 28 (45.8 > 38.7%), 45 (40.4 > 36.3%), and 90 (38.4 > 31.9%) after AI. Treatment with hCG improved conception rate in cows losing body condition between AI and d 28 after Al. Pregnancy losses were similar between treatment groups. Treatment with hCG on d 5 after AI induces accessory CL, enhances plasma progesterone concentration, and improves conception rate of high-producing dairy cows.

A review of the evaluation of TENORM levels at the produced water lagoon of the Minagish oil field using high-resolution gamma-ray spectrometry

NASA Astrophysics Data System (ADS)

Shams, H. M.; Bradley, D. A.; Alshammari, H.; Regan, P. H.

2017-11-01

An evaluation of the specific activity concentrations associated with technologically enhanced naturally occurring radioactive materials (TENORM) and anthropogenic radionuclides has been undertaken as part of a systematic study to provide a radiological map of the outer boundary of the produced water lagoon located in the Minagish oil field in the south west of the State of Kuwait. The lagoon contains material from the discharge of produced water which is a by-product of oil production in the region. The lagoon samples were prepared and placed into sealed, marinelli beakers for a full gamma-ray spectrometric analysis using a high-resolution, low-background, high-purity germanium detection systems at the University of Surrey Environmental Radioactivity Laboratory. Of particular interest are the calculation of the activity concentrations associated with members of the decay chains following decays of the primordial radionuclides of the 238U chain (226Ra, 214Pb, 214Bi) and the 232Th chain (228Ra, 228Ac, 212Pb, 212Bi, 208Tl), and the enhanced concentrations of radium isotopes. This conference paper presents an overview summary of the experimental samples which have been measured and the analysis techniques applied, including isotopic correlation plots across the sample region. The result shows the expected significant increase in 226Ra (and progeny) concentrations compared to the NORM values previously reported by our group for the overall terrain in Kuwait.

Draft Genome Sequence of Sporolactobacillus inulinus Strain CASD, an Efficient d-Lactic Acid-Producing Bacterium with High-Concentration Lactate Tolerance Capability

PubMed Central

Yu, Bo; Su, Fei; Wang, Limin; Xu, Ke; Zhao, Bo; Xu, Ping

2011-01-01

Sporolactobacillus inulinus CASD is an efficient d-lactic acid producer with high optical purity. Here we report for the first time the draft genome sequence of S. inulinus (2,930,096 bp). The large number of annotated two-component system genes makes it possible to explore the mechanism of extraordinary lactate tolerance of S. inulinus CASD. PMID:21952540

Draft genome sequence of Sporolactobacillus inulinus strain CASD, an efficient D-lactic acid-producing bacterium with high-concentration lactate tolerance capability.

PubMed

Yu, Bo; Su, Fei; Wang, Limin; Xu, Ke; Zhao, Bo; Xu, Ping

2011-10-01

Sporolactobacillus inulinus CASD is an efficient D-lactic acid producer with high optical purity. Here we report for the first time the draft genome sequence of S. inulinus (2,930,096 bp). The large number of annotated two-component system genes makes it possible to explore the mechanism of extraordinary lactate tolerance of S. inulinus CASD.

Speciation and environmental risk assessment of heavy metal in bio-oil from liquefaction/pyrolysis of sewage sludge.

PubMed

Yuan, Xingzhong; Leng, Lijian; Huang, Huajun; Chen, Xiaohong; Wang, Hou; Xiao, Zhihua; Zhai, Yunbo; Chen, Hongmei; Zeng, Guangming

2015-02-01

Liquefaction bio-oil (LBO) produced with ethanol (or acetone) as the solvent and pyrolysis bio-oil (PBO) produced at 550°C (or 850°C) from sewage sludge (SS) were produced, and were characterized and evaluated in terms of their heavy metal (HM) composition. The total concentration, speciation and leaching characteristic of HMs (Cu, Cr, Pb, Zn, Cd, and Ni) in both LBO and PBO were investigated. The total concentration and exchangeable fraction of Zn and Ni in bio-oils were at surprisingly high levels. Quantitative risk assessment of HM in bio-oils was performed by the method of risk assessment code (RAC), potential ecological risk index (PERI) and geo-accumulation index (GAI). Ni in bio-oil produced by pyrolysis at 850°C (PBO850) and Zn in bio-oil by liquefaction at 360°C with ethanol as solvent (LBO-360E) were evaluated to possess very high risk to the environment according to RAC. Additionally, Cd in PBO850 and LBO-360E were evaluated by PERI to have very high risk and high risk, respectively, while Cd in all bio-oils was assessed moderately contaminated according to GAI. Copyright © 2014 Elsevier Ltd. All rights reserved.

Thermo-stability, dose effects and shelf-life of antifungal metabolite-containing supernatants produced by Xenorhabdus szentirmai

USDA-ARS?s Scientific Manuscript database

Xenorhabdus spp. produce secondary metabolites that are antifungal to protect nematode-infected cadavers from fungal colonization. In previous work, the concentrated, or cell-free metabolites of X. szentirmaii exhibited high toxicity against various fungal plant pathogens and showed great potential ...

Sensory Effects of Menthol and Nicotine in an E-Cigarette.

PubMed

Rosbrook, Kathryn; Green, Barry G

2016-07-01

Despite the longstanding use and popularity of menthol as a flavorant in tobacco products, its sensory interactions with inhaled nicotine have never been measured independently of the other irritants in tobacco smoke. We therefore measured the perception of menthol in an E-cigarette with the primary goal of assessing its analgesic effect on the sensory irritation produced by inhaled nicotine. Adult cigarette smokers sampled aerosolized E-liquids containing five different concentrations of nicotine with 0%, 0.5%, or 3.5% l-menthol, as well as two commercial menthol flavors with and without nicotine. For each of the E-liquids participants used a labeled magnitude scale to rate the Overall Sensation intensity, Coolness/Cold, and Irritation/Harshness they experienced, and a Labeled Hedonic Scale to indicate how much they liked/disliked the overall flavor. The main findings were that (1) perceived Irritation/Harshness was unaffected by a low (0.5%) menthol concentration, whereas a high menthol concentration (3.5%) led to higher perceived Irritation/Harshness at low nicotine concentrations but to lower Irritation/Harshness at the highest nicotine concentration (24mg/ml); (2) a commercial Menthol-Mint flavor produced similar results; (3) nicotine tended to enhance rather than suppress sensations of Coolness/Cold; and (4) menthol tended to slightly increase liking independently of nicotine concentration. In addition to adding a sensation of coolness, menthol can reduce perceived airway irritation and harshness produced by inhalation when nicotine concentration is high, and contributes to the sensory impact of E-liquids when nicotine concentration is low. The evidence presented here indicates that menthol can potentially improve the appeal of E-cigarettes not only via its coolness and minty flavor, but also by reducing the harshness from high concentrations of nicotine. As the first direct demonstration of an analgesic effect of menthol on inhaled nicotine in humans, these data also have implications for the role of menthol flavors in other inhaled tobacco products. © The Author 2016. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Organic and inorganic species in produced water: Implications for water reuse

USGS Publications Warehouse

Kharaka, Yousif K.; Rice, Cynthia A.

2004-01-01

Currently 20-30 billion barrels of formation water are co-produced annually in the USA with conventional oil and natural gas. The large database on the geochemistry of this produced water shows salinities that vary widely from ~5,000 to >350,000 mg/L TDS. Chloride, Na and Ca are generally the dominant ions, and concentrations of Fe, Mn, B, NH3 and dissolved organics, including, BTEX, phenols and poly aromatic hydrocarbons (PAHs) may be relatively high. Hazardous concentrations of NORMs, including Ra-226 and Rn-222 have been reported in produced water from several states.Coal-bed methane (CBM) wells currently produce close to a billion barrels of water and deliver ~8% of total natural gas. The salinity of this produced water generally is lower than that of water from petroleum wells; salinity commonly is 1,000-20,000 mg/L, but ranges to150,000 mg/L TDS. Most CBM wells produce Na-HCO3-Cl type water that is low in trace metals and has no reported NORMs. This water commonly has no oil and grease and has relatively low DOC, but its organic composition has not been characterized in detail. The water is disposed of by injection into saline aquifers, through evaporation and/or percolation in disposal pits, road spreading, and surface discharge. Water that has an acceptable salinity and sodium absorption ratio (SAR) is considered acceptable for surface discharge and for injection into freshwater aquifers.As an alternative to costly disposal, low salinity produced water is being considered for reclamation, especially in the arid western USA. The cost of reclaiming this water to meet irrigation, industrial and drinking water standards was evaluated in a 10 gpm pilot field study at Placerita oil field, California. This produced water had a low salinity of ~8,000 mg/L, but high concentration of Si and organics. Removal of B, Si, NH3 and especially organics from this water proved difficult, and the estimated treatment cost was high at $0.08-$0.39/bbl for water treated for industrial and municipal uses.

Foaming of aluminium-silicon alloy using concentrated solar energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cambronero, L.E.G.; Ruiz-Roman, J.M.; Canadas, I.

2010-06-15

Solar energy is used for the work reported here as a nonconventional heating system to produce aluminium foam from Al-Si alloy precursors produced by powder metallurgy. A commercial precursor in cylindrical bars enclosed in a stainless-steel mould was heated under concentrated solar radiation in a solar furnace with varied heating conditions (heating rate, time, and temperature). Concentrated solar energy close to 300 W/cm{sup 2} on the mould is high enough to achieve complete foaming after heating for only 200 s. Under these conditions, the density and pore distribution in the foam change depending on the solar heating parameters and mouldmore » design. (author)« less

Stable, concentrated solutions of polyaniline using amines as gel inhibitors

DOEpatents

Wang, Hsing-Lin; Mattes, Benjamin R.

2002-01-01

Stable, concentrated solutions of high-molecular weight polyaniline using amines as gel inhibitors. Certain amine compounds (gel inhibitors) are used to form highly concentrated, stable solutions of the emeraldine base form of polyaniline in numerous organic solvents from which coatings, films and fibers are readily prepared without problems associated with rapid gelation which occurs when concentrated solutions are attempted without the use of the gel inhibitors of the present invention. Tertiary amines are used to solubilize low-molecular weight fractions (M.sub.w <120,000, M.sub.n <30,000) of the pernigraniline, emeraldine, and leucoemeraldine oxidation states of polyaniline as concentrated (>20 wt. %) polyaniline solutions, while primary and secondary amines are used to produce solutions having 15-40 wt % of high-molecular weight polyaniline [M.sub.w.gtoreq.120,000, M.sub.n.gtoreq.30,000]. Concentrated solutions of polyaniline co-polymers or ring and/or nitrogen-substituted polyanilines may also be prepared.

Sewage treatment method

DOEpatents

Fassbender, Alex G.

1995-01-01

The invention greatly reduces the amount of ammonia in sewage plant effluent. The process of the invention has three main steps. The first step is dewatering without first digesting, thereby producing a first ammonia-containing stream having a low concentration of ammonia, and a second solids-containing stream. The second step is sending the second solids-containing stream through a means for separating the solids from the liquid and producing an aqueous stream containing a high concentration of ammonia. The third step is removal of ammonia from the aqueous stream using a hydrothermal process.

High ethanol producing derivatives of Thermoanaerobacter ethanolicus

DOEpatents

Ljungdahl, L.G.; Carriera, L.H.

1983-05-24

Derivatives of the newly discovered microorganism Thermoanaerobacter ethanolicus which under anaerobic and thermophilic conditions continuously ferment substrates such as starch, cellobiose, glucose, xylose and other sugars to produce recoverable amounts of ethanol solving the problem of fermentations yielding low concentrations of ethanol using the parent strain of the microorganism Thermoanaerobacter ethanolicus are disclosed. These new derivatives are ethanol tolerant up to 10% (v/v) ethanol during fermentation. The process includes the use of an aqueous fermentation medium, containing the substrate at a substrate concentration greater than 1% (w/v).

High ethanol producing derivatives of Thermoanaerobacter ethanolicus

DOEpatents

Ljungdahl, Lars G.; Carriera, Laura H.

1983-01-01

Derivatives of the newly discovered microorganism Thermoanaerobacter ethanolicus which under anaerobic and thermophilic conditions continuously ferment substrates such as starch, cellobiose, glucose, xylose and other sugars to produce recoverable amounts of ethanol solving the problem of fermentations yielding low concentrations of ethanol using the parent strain of the microorganism Thermoanaerobacter ethanolicus are disclosed. These new derivatives are ethanol tolerant up to 10% (v/v) ethanol during fermentation. The process includes the use of an aqueous fermentation medium, containing the substrate at a substrate concentration greater than 1% (w/v).

A selective electrocatalyst–based direct methanol fuel cell operated at high concentrations of methanol

PubMed Central

Feng, Yan; Liu, Hui; Yang, Jun

2017-01-01

Owing to the serious crossover of methanol from the anode to the cathode through the polymer electrolyte membrane, direct methanol fuel cells (DMFCs) usually use dilute methanol solutions as fuel. However, the use of high-concentration methanol is highly demanded to improve the energy density of a DMFC system. Instead of the conventional strategies (for example, improving the fuel-feed system, membrane development, modification of electrode, and water management), we demonstrate the use of selective electrocatalysts to run a DMFC at high concentrations of methanol. In particular, at an operating temperature of 80°C, the as-fabricated DMFC with core-shell-shell Au@Ag2S@Pt nanocomposites at the anode and core-shell Au@Pd nanoparticles at the cathode produces a maximum power density of 89.7 mW cm−2 at a methanol feed concentration of 10 M and maintains good performance at a methanol concentration of up to 15 M. The high selectivity of the electrocatalysts achieved through structural construction accounts for the successful operation of the DMFC at high concentrations of methanol. PMID:28695199

A selective electrocatalyst-based direct methanol fuel cell operated at high concentrations of methanol.

PubMed

Feng, Yan; Liu, Hui; Yang, Jun

2017-06-01

Owing to the serious crossover of methanol from the anode to the cathode through the polymer electrolyte membrane, direct methanol fuel cells (DMFCs) usually use dilute methanol solutions as fuel. However, the use of high-concentration methanol is highly demanded to improve the energy density of a DMFC system. Instead of the conventional strategies (for example, improving the fuel-feed system, membrane development, modification of electrode, and water management), we demonstrate the use of selective electrocatalysts to run a DMFC at high concentrations of methanol. In particular, at an operating temperature of 80°C, the as-fabricated DMFC with core-shell-shell Au@Ag 2 S@Pt nanocomposites at the anode and core-shell Au@Pd nanoparticles at the cathode produces a maximum power density of 89.7 mW cm -2 at a methanol feed concentration of 10 M and maintains good performance at a methanol concentration of up to 15 M. The high selectivity of the electrocatalysts achieved through structural construction accounts for the successful operation of the DMFC at high concentrations of methanol.

Impact of radon gas concentration in the aerosoles profile

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lukaj, Edmond, E-mail: mondilukaj@yahoo.com; Vila, Floran, E-mail: floranvila@yahoo.com; Mandija, Florian, E-mail: fmandija@yahoo.com

Radon gases relased from building materials and from earth surface are the major responsibility of air ionization. Radon nuclear decay can produce an alpha particle with high energy and Radon progeny. This particle and gamma rays can deliver particles in the air and produce ions with different polarities. This ions, because of induced electric charge, can attach with air aerosols and charge them with their electric charge. The charged aerosols can interact with the other aerosols and ions. Because of this exchange, the air conductivity and the aerosol profiles will change dependently by Radon gas concentration and gamma radiation. Observationsmore » show an increase in concentration of Radon during the night, and a decrease during the daylight time. The Radon gas concentration changed hour by hour can induce aerosol profile to change. This dependency between the aerosol profiles and the Radon gas concentrations is discussed.« less

Organic compounds in produced waters from coalbed natural gas wells in the Powder River Basin, Wyoming, USA

USGS Publications Warehouse

Orem, W.H.; Tatu, C.A.; Lerch, H.E.; Rice, C.A.; Bartos, T.T.; Bates, A.L.; Tewalt, S.; Corum, M.D.

2007-01-01

The organic composition of produced water samples from coalbed natural gas (CBNG) wells in the Powder River Basin, WY, sampled in 2001 and 2002 are reported as part of a larger study of the potential health and environmental effects of organic compounds derived from coal. The quality of CBNG produced waters is a potential environmental concern and disposal problem for CBNG producers, and no previous studies of organic compounds in CBNG produced water have been published. Organic compounds identified in the produced water samples included: phenols, biphenyls, N-, O-, and S-containing heterocyclic compounds, polycyclic aromatic hydrocarbons (PAHs), aromatic amines, various non-aromatic compounds, and phthalates. Many of the identified organic compounds (phenols, heterocyclic compounds, PAHs) are probably coal-derived. PAHs represented the group of organic compounds most commonly observed. Concentrations of total PAHs ranged up to 23 ??g/L. Concentrations of individual compounds ranged from about 18 to <0.01 ??g/L. Temporal variability of organic compound concentrations was documented, as two wells with relatively high organic compound contents in produced water in 2001 had much lower concentrations in 2002. In many areas, including the PRB, coal strata provide aquifers for drinking water wells. Organic compounds observed in produced water are also likely present in drinking water supplied from wells in the coal. Some of the organic compounds identified in the produced water samples are potentially toxic, but at the levels measured in these samples are unlikely to have acute health effects. The human health effects of low-level, chronic exposure to coal-derived organic compounds in drinking water are currently unknown. Continuing studies will evaluate possible toxic effects from low level, chronic exposure to coal-derived organic compounds in drinking water supplies.

Helium isotopes in ferromanganese crusts from the central Pacific Ocean

USGS Publications Warehouse

Basu, S.; Stuart, F.M.; Klemm, V.; Korschinek, G.; Knie, K.; Hein, J.R.

2006-01-01

Helium isotopes have been measured in samples of two ferromanganese crusts (VA13/2 and CD29-2) from the central Pacific Ocean. With the exception of the deepest part of crust CD29-2 the data can be explained by a mixture of implanted solar- and galactic cosmic ray-produced (GCR) He, in extraterrestrial grains, and radiogenic He in wind-borne continental dust grains. 4He concentrations are invariant and require retention of less than 12% of the in situ He produced since crust formation. Loss has occurred by recoil and diffusion. High 4He in CD29-2 samples older than 42 Ma are correlated with phosphatization and can be explained by retention of up to 12% of the in situ-produced 4He. 3He/4He of VA13/2 samples varies from 18.5 to 1852 Ra due almost entirely to variation in the extraterrestrial He contribution. The highest 3He/4He is comparable to the highest values measured in interplanetary dust particles (IDPs) and micrometeorites (MMs). Helium concentrations are orders of magnitude lower than in oceanic sediments reflecting the low trapping efficiency for in-falling terrestrial and extraterrestrial grains of Fe-Mn crusts. The extraterrestrial 3He concentration of the crusts rules out whole, undegassed 4–40 μm diameter IDPs as the host. Instead it requires that the extraterrestrial He inventory is carried by numerous particles with significantly lower He concentrations, and occasional high concentration GCR-He-bearing particles.

Optimization of a Nafion Membrane-Based System for Removal of Chloride and Fluoride from Lunar Regolith-Derived Water

NASA Technical Reports Server (NTRS)

Anthony, Stephen M.; Santiago-Maldonado, Edgardo; Captain, James G.; Pawate, Ashtamurthy S.; Kenis, Paul J. A.

2012-01-01

A long-term human presence in space will require self-sustaining systems capable of producing oxygen and potable water from extraterrestrial sources. Oxygen can be extracted from lunar regolith, and water contaminated with hydrochloric and hydrofluoric acids is produced as an intermediate in this process. We investigated the ability of Nafion proton exchange membranes to remove hydrochloric and hydrofluoric acids from water. The effect of membrane thickness, product stream flow rate, and acid solution temperature and concentration on water flux, acid rejection, and water and acid activity were studied. The conditions that maximized water transport and acid rejection while minimizing resource usage were determined by calculating a figure of merit. Water permeation is highest at high solution temperature and product stream flow rate across thin membranes, while chloride and fluoride permeation are lowest at low acid solution temperature and concentration across thin membranes. The figure of merit varies depending on the starting acid concentration; at low concentration, the figure of merit is highest across a thin membrane, while at high concentration, the figure of merit is highest at low solution temperature. In all cases, the figure of merit increases with increasing product stream flow rate.

Genetic link between EMI and EMII: An adakite connection

NASA Astrophysics Data System (ADS)

Shimoda, Gen

2009-10-01

Geochemical modeling of the origin of enriched mantle I (EMI) and enriched mantle II (EMII) is conducted from the perspective of adakite production. For the model, the average composition of adakites is re-estimated from published data for eighteen trace elements. Although the concentrations determined for highly incompatible elements are very high (about 100 times of primitive mantle), these high concentrations can be explained by melting of oceanic crust without sediment contribution. The compiled data further suggest that the mantle-slab melt reaction would play a major role in the production of basic adakites. In addition, crystal fractionation in the magma chamber should produce additional chemical variations in adakites, in particular for acidic adakites. To examine the effect of chemical variations on the isotopic composition of recycled adakites, broad correlations between trace elements and SiO 2 concentrations, and the MELTS program are employed. The results suggest that recycling of a basic adakite (SiO 2 = 55%) can account for EMI isotopic signatures with storage times of about 2.0 Gyr. The isotopic compositions of less-basic adakites and their evolved magmas shift towards EMII values with increasing SiO 2 concentrations. In particular, evolved acidic adakite can yield EMII isotopic signatures. These lines of evidence suggest that the recycling of adakites at various stages of evolution can conceivably produce the entire isotopic range between EMI and EMII reservoirs. Consequently, adakite recycling via sediment subduction or subduction erosion can account for the origins of EMI and EMII reservoirs. In this context, residual garnet under high pressure and plagioclase fractionation at low pressure might play an essential role in producing the chemical variations among adakites that ultimately govern the isotopic compositions of these geochemical reservoirs.

Very high gravity ethanol and fatty acid production of Zymomonas mobilis without amino acid and vitamin.

PubMed

Wang, Haoyong; Cao, Shangzhi; Wang, William Tianshuo; Wang, Kaven Tianyv; Jia, Xianhui

2016-06-01

Very high gravity (VHG) fermentation is the mainstream technology in ethanol industry, which requires the strains be resistant to multiple stresses such as high glucose concentration, high ethanol concentration, high temperature and harsh acidic conditions. To our knowledge, it was not reported previously that any ethanol-producing microbe showed a high performance in VHG fermentations without amino acid and vitamin. Here we demonstrate the engineering of a xylose utilizing recombinant Zymomonas mobilis for VHG ethanol fermentations. The recombinant strain can produce ethanol up to 136 g/L without amino acid and vitamin with a theoretical yield of 90 %, which is significantly superior to that produced by all the reported ethanol-producing strains. The intracellular fatty acids of the bacterial were about 16 % of the bacterial dry biomass, with the ratio of ethanol:fatty acids was about 273:1 (g/g). The recombinant strain was achieved by a multivariate-modular strategy tackles with the multiple stresses which are closely linked to the ethanol productivity of Z. mobilis. The over-expression of metB/yfdZ operon enabled the growth of the recombinant Z. mobilis in a chemically defined medium without amino acid and vitamin; and the fatty acids overproduction significantly increased ethanol tolerance and ethanol production. The coupled production of ethanol with fatty acids of the Z. mobilis without amino acid and vitamin under VHG fermentation conditions may permit a significant reduction of the production cost of ethanol and microbial fatty acids.

Zwitterionic Antifouling Coatings for the Purification of High-Salinity Shale Gas Produced Water.

PubMed

Yang, Rong; Goktekin, Esma; Gleason, Karen K

2015-11-03

Fouling refers to the undesirable attachment of organic molecules and microorganisms to submerged surfaces. It is an obstacle to the purification of shale gas produced water and is currently without an effective solution due to the highly contaminated nature of produced water. Here, we demonstrate the direct vapor application of a robust zwitterionic coating to a variety of substrates. The coating remains unprecedentedly hydrophilic, smooth, and effectively antifouling in extremely high salinity solutions (with salt concentration of 200,000 ppm). The fouling resistance is assessed rapidly and quantitatively with a molecular force spectroscopy-based method and corroborated using quartz crystal microbalance system with dissipation monitoring. Grazing angle attenuated total reflectance Fourier transform infrared is used in combination with X-ray photoelectron spectroscopy, atomic force microscope, and in situ spectroscopic ellipsometry to lend insight into the underlying mechanism for the exceptional stability and effectiveness of the zwitterionic coating under high-salinity conditions. A unique coating architecture, where the surface is concentrated with mobile zwitterionic moieties while the bulk is cross-linked to enhance coating durability, was discovered to be the origin of its stable fouling resistance under high salinity. Combined with previously reported exceptional stability in highly oxidative environments and strong fouling resistance to oil and grease, the zwitterionic surface here has the potential to enable low-cost, membrane-based techniques for the purification of produced water and to eventually balance the favorable economics and the concerning environmental impacts of the hydraulic fracturing industry.

Effects of sodium fluoride on immune response in murine macrophages.

PubMed

De la Fuente, Beatriz; Vázquez, Marta; Rocha, René Antonio; Devesa, Vicenta; Vélez, Dinoraz

2016-08-01

Excessive fluoride intake may be harmful for health, producing dental and skeletal fluorosis, and effects upon neurobehavioral development. Studies in animals have revealed effects upon the gastrointestinal, renal and reproductive systems. Some of the disorders may be a consequence of immune system alterations. In this study, an in vitro evaluation is made of fluoride immunotoxicity using the RAW 264.7 murine macrophage line over a broad range of concentrations (2.5-75mg/L). The results show that the highest fluoride concentrations used (50-75mg/L) reduce the macrophage population in part as a consequence of the generation of reactive oxygen and/or nitrogen species and consequent redox imbalance, which in turn is accompanied by lipid peroxidation. A decrease in the expression of the antiinflammatory cytokine Il10 is observed from the lowest concentrations (5mg/L). High concentrations (50mg/L) in turn produce a significant increase in the proinflammatory cytokines Il6 and Mip2 from 4h of exposure. In addition, cell phagocytic capacity is seen to decrease at concentrations of ≥20mg/L. These data indicate that fluoride, at high concentrations, may affect macrophages and thus immune system function - particularly with regard to the inflammation autoregulatory processes, in which macrophages play a key role. Copyright © 2016 Elsevier B.V. All rights reserved.

Zinc accumulation by the slime mold Fuligo septica (L.) Wiggers in the former Soviet Union and North Korea.

PubMed

Zhulidov, Daniel A; Robarts, Richard D; Zhulidov, Alexander V; Zhulidova, Olga V; Markelov, Danila A; Rusanov, Viktor A; Headley, John V

2002-01-01

Samples of the slime mold Fuligo septica (L.) Wiggers were collected from an ecologically diverse selection of sites across the former USSR and in North Korea to determine their Zn concentrations. Plasmodia were collected from trees, rocks, soils, the walls of buildings and a variety of other materials and structures from 1990 to 1996. The biomass collected ranged from 305 to 968 mg, whereas Zn concentrations in plasmodia of F. septica ranged from 8400 to 23,000 mg kg(-1) dry wt. (mean and standard error = 14,200 +/- 860 mg kg(-1) dry wt.). No clear trend as to which areas produced F. septica with the highest Zn concentrations was discernable. Nor was it possible to identify any particular substrate on which F. septica grew that produced noticeably high Zn concentrations. For example, forest litter on which F. septica was found had Zn concentrations of only 25 to 130 mg kg(-1) dry wt. Our data confirm the only other study showing hyperaccumulation of Zn in F. septica, which was carried out in Finland. This ability seems to be unique to this species, but how or why it does this, or why such high Zn concentrations are not toxic to F. septica, are questions requiring future research.

Plant protein and secondary metabolites influence diet selection in a mammalian specialist herbivore

Treesearch

Amy C. Ulappa; Rick G. Kelsey; Graham G. Frye; Janet L. Rachlow; LIsa A. Shipley; Laura Bond; Xinzhu Pu; Jennifer Sorensen Forbey

2014-01-01

For herbivores, nutrient intake is limited by the relatively low nutritional quality of plants and high concentrations of potentially toxic defensive compounds (plant secondary metabolites [PSMs]) produced by many plants. In response to phytochemical challenges, some herbivores selectively forage on plants with higher nutrient and lower PSM concentrations relative to...

Solid aerosol generator

DOEpatents

Prescott, Donald S.; Schober, Robert K.; Beller, John

1992-01-01

An improved solid aerosol generator used to produce a gas borne stream of dry, solid particles of predetermined size and concentration. The improved solid aerosol generator nebulizes a feed solution of known concentration with a flow of preheated gas and dries the resultant wet heated aerosol in a grounded, conical heating chamber, achieving high recovery and flow rates.

Novel technologies for enhanced production of ethanol: impact of high productivity on process economics

USDA-ARS?s Scientific Manuscript database

In these studies Saccharomyces cerevisiae NRRL Y-566 was used to produce ethanol from a concentrated glucose (250-300 gL-1) solution. When fermentation media were supplemented with CaCO3 and CaCl2, ethanol concentrations, yield, and productivities were improved significantly. In control batch fermen...

Changes in ovarian function associated with circulating concentrations of estradiol prior to a GnRH-induced ovulation in beef cows

USDA-ARS?s Scientific Manuscript database

Previous reports suggest increased circulating concentrations of estradiol prior to GnRH induced ovulation improved conception rates and pregnancy maintenance in beef cattle, and cultured granulosa cells from animals with high antral follicle numbers produced more estradiol and had increased express...

Mutant strain of C. acetobutylicum and process for making butanol

DOEpatents

Jain, Mahendra K.; Beacom, Daniel; Datta, Rathin

1993-01-01

A biologically pure asporogenic mutant of Clostridium acetobutylicum is produced by growing sporogenic C. acetobutylicum ATCC 4259 and treating the parent strain with ethane methane sulfonate. The mutant which as been designated C. acetobutylicum ATCC 55025 is useful in an improved ABE fermentation process, and produces high concentrations of butanol and total solvents.

Quantity and quality of secoiridoids and lignans in extra virgin olive oils: the effect of two- and three-way decanters on Leccino and Raggiola olive cultivars.

PubMed

Antonini, Elena; Farina, Alfonso; Scarpa, Emanuele Salvatore; Frati, Alessandra; Ninfali, Paolino

2016-01-01

In this investigation, 14 extra virgin olive oils (EVOOs), produced with Leccino and Raggiola olive cultivars, by a new two-way (2W) decanter were compared with 14 EVOOs produced by means of a conventional three-way (3W) decanter. The 2W EVOOs had higher phenol concentrations, as shown by high-performance liquid chromatography/diode array detection (HPLC-DAD) analysis and yielded a higher extraction of the 3,4-DHPEA-EDA (oleacein), 3,4-DHPEA-EA (oleuropein aglycone) and p-HPEA-EDA (oleocanthal). The concentrations of lignans, (+)-pinoresinol and (+)-1-acetoxypinoresinol, detected by HPLC-FLD equipment, were higher in the 2W EVOOs than they were in EVOOs produced using the 3W system. Total phenols, detected by the Folin-Ciocalteu assay, were lower than those obtained by HPLC, but they significantly correlated (p < 0.05). The antioxidant capacity (ORAC) values of 2W EVOOs were higher than those of 3W EVOOs. In conclusion, the 2W system provided high-quality phenol EVOOs and became an indispensable tool when adverse climatic conditions reduced the olive secoiridoid concentration.

Assesment of trace elements and organic pollutants from a marine oil complex into the coral reef system of Cayo Arcas, Mexico.

PubMed

Cram, Silke; Ponce De León, Claudia A; Fernández, Pilar; Sommer, Irene; Rivas, Hilda; Morales, Luis Miguel

2006-10-01

Possible contaminants produced by the Petroleos Mexicanos (PEMEX) marine oil complex in the vicinity of the Cayo Arcas (Mexico) coral reef ecosystem were evaluated by analyzing sediments and sea water for hydrocarbons and metal elements. We found that the concentrations of aliphatic hydrocarbons in the sea water were generally low, with the highest values detected near the oil station; the concentration of polycyclic aromatic hydrocarbons (PAHs) was generally below the detection limit. The hydrocarbons found in the sediments seem to have a pyrogenic origin, and were probably produced by marine traffic in the study area. The total PAH concentration did not exceed the NOAA criteria, although levels of some individual PAHs did. The only metal detected in the sea water at high concentrations was nickel. The Ni/V ratio in the sediments indicates the contribution of crude oil to the system. The high content of Ni and Zn was attributed to the ballast waters from the oil tankers that load at the station's monobuoys. The presence of fine sediments that commonly originate from terrestrial ecosystems supported this assumption.

Traveling around Cape Horn: Otolith chemistry reveals a mixed stock of Patagonian hoki with separate Atlantic and Pacific spawning grounds

USGS Publications Warehouse

Schuchert, P.C.; Arkhipkin, A.I.; Koenig, A.E.

2010-01-01

Trace element fingerprints of edge and core regions in otoliths from 260 specimens of Patagonian hoki, Macruronus magellanicus L??nnberg, 1907, were analyzed by LA-ICPMS to reveal whether this species forms one or more population units (stocks) in the Southern Oceans. Fish were caught on their spawning grounds in Chile and feeding grounds in Chile and the Falkland Islands. Univariate and multivariate analyses of trace element concentrations in the otolith edges, which relate to the adult life of fish, could not distinguish between Atlantic (Falkland) and Pacific (Chile) hoki. Cluster analyses of element concentrations in the otolith edges produced three different clusters in all sample areas indicating high mixture of the stocks. Cluster analysis of trace element concentrations in the otolith cores, relating to juvenile and larval life stages, produced two separate clusters mainly distinguished by 137Ba concentrations. The results suggest that Patagonian hoki is a highly mixed fish stock with at least two spawning grounds around South America. ?? 2009 Elsevier B.V.

Copper-complexing ligands produced by an intact estuarine microbial community in response to copper stress.

NASA Astrophysics Data System (ADS)

Bingham, J.; Dryden, C.; Gordon, A.

2002-12-01

Copper is both an important nutrient and a pollutant in the marine environment. By studying the interactions between microorganisms and copper in the Elizabeth River (VA), home to a major Naval Base, we field tested the hypothesis that picoplankton and/or bacterioplankton produce strong, copper-complexing ligands in response to elevated copper concentrations. A simple light/ dark test was used to distinguish between heterotrophic and phototrophic ligand production. Samples were bottled and moored, submerged one meter, for a week. Direct counts using DAPI stain and epiflourescence were conducted to find concentrations of picoplankton and bacterioplankton. Using cathodic stripping voltammetry, we found the total copper concentrations, and then from a titration of the ligands by copper, the ligand concentrations and conditional stability constants were obtained. The Elizabeth River naturally had between 10-20 nM total dissolved copper concentrations. However when copper complexation was considered we found that the levels of bio-available Cu(II) ions were much lower. In fact in the natural samples the levels were not high enough to affect the relative reproductive rates of several microorganisms. Naturally there was a 50 nM "buffer zone" of ligand to total dissolved copper concentration. Furthermore, when stressed with excess copper, healthy picoplankton produced enough ligand to alleviate toxicity, and rebuild the buffer zone. However bacterioplankton only produced enough ligand so that they were no longer affected. Therefore, intact estuarine communities regulate copper bioavailability and toxicity with ligand production.

Investigation of the Spatiotemporal Responses of Nanoparticles in Tumor Tissues with a Small-Scale Mathematical Model

PubMed Central

Chou, Cheng-Ying; Huang, Chih-Kang; Lu, Kuo-Wei; Horng, Tzyy-Leng; Lin, Win-Li

2013-01-01

The transport and accumulation of anticancer nanodrugs in tumor tissues are affected by many factors including particle properties, vascular density and leakiness, and interstitial diffusivity. It is important to understand the effects of these factors on the detailed drug distribution in the entire tumor for an effective treatment. In this study, we developed a small-scale mathematical model to systematically study the spatiotemporal responses and accumulative exposures of macromolecular carriers in localized tumor tissues. We chose various dextrans as model carriers and studied the effects of vascular density, permeability, diffusivity, and half-life of dextrans on their spatiotemporal concentration responses and accumulative exposure distribution to tumor cells. The relevant biological parameters were obtained from experimental results previously reported by the Dreher group. The area under concentration-time response curve (AUC) quantified the extent of tissue exposure to a drug and therefore was considered more reliable in assessing the extent of the overall drug exposure than individual concentrations. The results showed that 1) a small macromolecule can penetrate deep into the tumor interstitium and produce a uniform but low spatial distribution of AUC; 2) large macromolecules produce high AUC in the perivascular region, but low AUC in the distal region away from vessels; 3) medium-sized macromolecules produce a relatively uniform and high AUC in the tumor interstitium between two vessels; 4) enhancement of permeability can elevate the level of AUC, but have little effect on its uniformity while enhancement of diffusivity is able to raise the level of AUC and improve its uniformity; 5) a longer half-life can produce a deeper penetration and a higher level of AUC distribution. The numerical results indicate that a long half-life carrier in plasma and a high interstitial diffusivity are the key factors to produce a high and relatively uniform spatial AUC distribution in the interstitium. PMID:23565142

Estimation of true serum thyroglobulin concentration using simultaneous measurement of serum antithyroglobulin antibody.

PubMed

Ahn, Byeong-Cheol; Lee, Won Kee; Jeong, Shin Young; Lee, Sang-Woo; Lee, Jaetae

2013-01-01

We investigated the analytical interference of antithyroglobulin antibody (TgAb) to thyroglobulin (Tg) measurement and tried to convert measured Tg concentration to true Tg concentration using a mathematical equation which includes a concentration of TgAb. Methods. Tg was measured by immunoradiometric assay and TgAb by radioimmunoassy. Experimental samples were produced by mixing Tg and TgAb standard solutions or mixing patients' serum with high Tg or high TgAb. Mathematical equations for prediction of expected Tg concentration with measured Tg and TgAb concentrations were deduced. The Tg concentration calculated using the equations was compared with the expected Tg concentration. Results. Measured Tg concentrations of samples having high TgAb were significantly lower than their expected Tg concentration. Magnitude of TgAb interference with the Tg assay showed a positive correlation with concentration of TgAb. Mathematical equations for estimation of expected Tg concentration using measured Tg and TgAb concentrations were successfully deduced and the calculated Tg concentration showed excellent correlation with expected Tg concentration. Conclusions. A mathematic equation for estimation of true Tg concentration using measured Tg and TgAb concentration was deduced. Tg concentration calculated by use of the equation might be more valuable than measured Tg concentration in patients with differentiated thyroid cancer.

A Behavioral and Genetic Dissection of Two Forms of Olfactory Plasticity in Caenorhabditis elegans: Adaptation and Habituation

PubMed Central

Bernhard, Nirit; van der Kooy, Derek

2000-01-01

Continuous presentation of an olfactory stimulus causes a decrement of the chemotaxis response in the nematode Caenorhabditis elegans. However, the differences between the learning process of habituation (a readily reversible decrease in behavioral response) and other types of olfactory plasticity such as adaptation (a decrement in response due to sensory fatigue, which cannot be dishabituated) have not been addressed. The volatile odorant diacetyl (DA) was used within a single paradigm to assess the distinct processes of olfactory adaptation and habituation. Preexposing and testing worms to 100% DA vapors caused a chemotaxis decrement that was not reversible despite the presentation of potentially dishabituating stimuli. This DA adaptation was abolished in worms with an odr-10 mutation (encoding a high-affinity DA receptor on the AWA neuron), even though naive chemotaxis remained unaffected. Conversely, DA adaptation remained intact in odr-1 mutants (defective in AWC neuron-mediated olfactory behavior), even though naive chemotaxis to DA decreased. Surprisingly, exposure to vapors of intermediate concentrations of DA (0.01% and 25%) did not cause worms to exhibit any response decrement. In contrast to preexposure to high DA concentrations, preexposure to low DA concentrations (0.001%) produced habituation of the chemotaxis response (a dishabituating stimulus could reverse the response decrement back to baseline levels). The distinct behavioral effects produced by DA preexposure highlight a concentration-dependent dissociation between two decremental olfactory processes: adaptation at high DA concentrations versus habituation at low DA concentrations. PMID:10940320

A combined physicochemical-biological method of NaCl extraction from the irrigation solution in the BTLSS

NASA Astrophysics Data System (ADS)

Trifonov, Sergey V.; Tikhomirov, Alexander A.; Ushakova, Sofya; Tikhomirova, Natalia

2016-07-01

The use of processed human wastes as a source of minerals for plants in closed biotechnical life support systems (BTLSS) leads to high salt levels in the irrigation solution, as urine contains high concentrations of NaCl. It is important to develop a process that would effectively decrease NaCl concentration in the irrigation solution and return this salt to the crew's diet. The salt-tolerant plants (Salicornia europea) used to reduce NaCl concentration in the irrigation solution require higher salt concentrations than those of the solution, and this problem cannot be resolved by concentrating the solution. At the same time, NaCl extracted from mineralized wastes by physicochemical methods is not pure enough to be included in the crew's diet. This study describes an original physicochemical method of NaCl extraction from the solution, which is intended to be used in combination with the biological method of NaCl extraction by using saltwort plants. The physicochemical method produces solutions with high NaCl concentrations, and saltwort plants serve as a biological filter in the final phase, to produce table salt. The study reports the order in which physicochemical and biological methods of NaCl extraction from the irrigation solution should be used to enable rapid and effective inclusion of NaCl into the cycling of the BTLSS with humans. This study was carried out in the IBP SB RAS and supported by the grant of the Russian Science Foundation (Project No. 14-14-00599).

Self-adaption of methane-producing communities to pH disturbance at different acetate concentrations by shifting pathways and population interaction.

PubMed

Hao, Liping; Lü, Fan; Li, Lei; Wu, Qing; Shao, Liming; He, Pinjing

2013-07-01

To investigate the competition among acetate-utilizing microorganisms at different acetate levels, bioconversion processes of 50, 100, 150 and 200 mM acetate in the presence and absence of methanogenic inhibitor CH3F were monitored in thermophilic methanogenic system. The successive response of methane-producing community during the deteriorative and recovery phases caused by pH disturbance was analyzed. High acetate concentration (>50mM) inhibited the activity of acetoclastic methanogenesis (AM). The increasing pH (>7.5) enhanced this inhibition. The syntrophic acetate oxidizing (SAO) bacteria and hydrogenotrophic methanogens including Methanomicrobiales and Methanobacteirales were more tolerant to the stress from high acetate concentration and high pH. Resumption from alkali condition to normal pH stimulated the growth of acetate oxidizing syntrophs. The reaction rate of SAO-HM was lower than that of AM. These results point to the possibility to regenerate the deteriorated anaerobic digesters by addition of acclimatized inocula rich in acetate-oxidizing syntrophs. Copyright © 2013 Elsevier Ltd. All rights reserved.

Morphology, nectar characteristics and avian pollinators in five Andean Puya species (Bromeliaceae)

NASA Astrophysics Data System (ADS)

Hornung-Leoni, C. T.; González-Gómez, P. L.; Troncoso, A. J.

2013-08-01

Five Andean Puya species (Puya alpestris, Puya chilensis, Puya coerulea, Puya raimondii and Puya venusta) were studied to determine the relationship between their avian visitors, and plant morphology and nectar characteristics. Our results showed a significant relationship between nectar concentration, presence of sterile apex and avian pollinators's species. In contrast, nectar composition was not related to the frequency of avian visits. We found that Puya species were mainly visited by specialist nectarivorous birds such as hummingbirds (i.e., P. coerulea and P. venusta), lacked a sterile apex and produced high nectar concentration in low volumes. In contrast, species mainly visited by generalist passerines (i.e., P. chilensis and P. alpestris) were characterized by the presence of a sterile apex and production of highly diluted nectar in large volumes. In a mono-specific group we found that P. raimondii produces highly concentrated nectar in large volumes, and its flowers were visited by hummingbirds and passerine birds. We found no effect of nectar composition on bird's visits. Our study highlights the interplay between morphological traits, nectar characteristics and the ecological framework to explain specialized and generalized birds pollination systems.

Biological nitrification/denitrification of high sodium nitrite (navy shipyard) wastewater.

PubMed

Kamath, S; Sabatini, D A; Canter, L W

1991-01-01

In the hydroblasting of ships' boiler tubes, a wastewater high in nitrite (as high as 1200 mg litre(-1)) is produced by the US Navy. This research has evaluated the use of a suspended-growth biological system to treat this wastewater by denitrification. Two biological treatment configurations were evaluated (direct denitrification versus nitrification/denitrification) with nitrification/denitrification producing better nitrite removal efficiencies (54 to 62% versus 40%, respectively). The introduction of metals (cadmium, chromium, lead, copper and iron) in concentrations typical for this wastewater did not inhibit the nitrite removal efficiencies. The influent metal concentrations ranged from 0.02 mg litre(-1) for cadmium to 22 mg litre(-1) for iron and the metal removal efficiencies ranged from 4.8% for cadmium to 50% for copper. Increasing sludge age resulted in improved nitrite removal efficiencies (52%, 57% and 74% for sludge ages of 4, 6 and 8 days, respectively). The resulting biokinetic constants were similar to those reported by others for lower influent concentrations of nitrite or nitrate (Ygs=0.02 mg/mg; Ygn=0.16 mg/mg; Yb=0.8 mg/mg; and b=0.006 h(-1)).

Mechanisms of Ethanol Tolerance in Saccharomyces cerevisiae

USDA-ARS?s Scientific Manuscript database

Saccharomyces cerevisiae is a superb ethanol producer, yet is also sensitive to higher ethanol concentrations especially under high gravity or very high gravity fermentation conditions. Ethanol tolerance is associated with interplay of complex networks at the genome level. Although significant eff...

Life-Cycle Assessment of Biodiesel Produced from Grease Trap Waste.

PubMed

Hums, Megan E; Cairncross, Richard A; Spatari, Sabrina

2016-03-01

Grease trap waste (GTW) is a low-quality waste material with variable lipid content that is an untapped resource for producing biodiesel. Compared to conventional biodiesel feedstocks, GTW requires different and additional processing steps for biodiesel production due to its heterogeneous composition, high acidity, and high sulfur content. Life-cycle assessment (LCA) is used to quantify greenhouse gas emissions, fossil energy demand, and criteria air pollutant emissions for the GTW-biodiesel process, in which the sensitivity to lipid concentration in GTW is analyzed using Monte Carlo simulation. The life-cycle environmental performance of GTW-biodiesel is compared to that of current GTW disposal, the soybean-biodiesel process, and low-sulfur diesel (LSD). The disposal of the water and solid wastes produced from separating lipids from GTW has a high contribution to the environmental impacts; however, the impacts of these processed wastes are part of the current disposal practice for GTW and could be excluded with consequential LCA system boundaries. At lipid concentrations greater than 10%, most of the environmental metrics studied are lower than those of LSD and comparable to soybean biodiesel.

Comprehensive characterization of glutamine synthetase-mediated selection for the establishment of recombinant CHO cells producing monoclonal antibodies.

PubMed

Noh, Soo Min; Shin, Seunghyeon; Lee, Gyun Min

2018-03-29

To characterize a glutamine synthetase (GS)-based selection system, monoclonal antibody (mAb) producing recombinant CHO cell clones were generated by a single round of selection at various methionine sulfoximine (MSX) concentrations (0, 25, and 50 μM) using two different host cell lines (CHO-K1 and GS-knockout CHO). Regardless of the host cell lines used, the clones selected at 50 μM MSX had the lowest average specific growth rate and the highest average specific production rates of toxic metabolic wastes, lactate and ammonia. Unlike CHO-K1, high producing clones could be generated in the absence of MSX using GS-knockout CHO with an improved selection stringency. Regardless of the host cell lines used, the clones selected at various MSX concentrations showed no significant difference in the GS, heavy chain, and light chain gene copies (P > 0.05). Furthermore, there was no correlation between the specific mAb productivity and these three gene copies (R 2  ≤ 0.012). Taken together, GS-mediated gene amplification does not occur in a single round of selection at a MSX concentration up to 50 μM. The use of the GS-knockout CHO host cell line facilitates the rapid generation of high producing clones with reduced production of lactate and ammonia in the absence of MSX.

Characteristics of hydrogen produced by partial oxidation and auto-thermal reforming in a small methanol reformer

NASA Astrophysics Data System (ADS)

Horng, Rong-Fang; Chou, Huann-Ming; Lee, Chiou-Hwang; Tsai, Hsien-Te

This paper investigates experimentally, the transient characteristics of a small methanol reformer using partial oxidation (POX) and auto-thermal reforming (ATR) for fuel cell applications. The parameters varied were heating temperature, methanol supply rate, steady mode shifting temperature, O 2/C (O 2/CH 3OH) and S/C (H 2O/CH 3OH) molar ratios with the main aim of promoting a rapid response and a high flow rate of hydrogen. The experiments showed that a high steady mode shifting temperature resulted in a faster temperature rise at the catalyst outlet and vice versa and that a low steady mode shifting temperature resulted in a lower final hydrogen concentration. However, when the mode shifting temperature was too high, the hydrogen production response was not necessarily improved. It was subsequently shown that the optimum steady mode shifting temperature for this experimental set-up was approximately 75 °C. Further, the hydrogen concentration produced by the auto-thermal process was as high as 49.12% and the volume flow rate up to 23.0 L min -1 compared to 40.0% and 20.5 L min -1 produced by partial oxidation.

Simplified production and concentration of HIV-1-based lentiviral vectors using HYPERFlask vessels and anion exchange membrane chromatography

PubMed Central

Kutner, Robert H; Puthli, Sharon; Marino, Michael P; Reiser, Jakob

2009-01-01

Background During the past twelve years, lentiviral (LV) vectors have emerged as valuable tools for transgene delivery because of their ability to transduce nondividing cells and their capacity to sustain long-term transgene expression in target cells in vitro and in vivo. However, despite significant progress, the production and concentration of high-titer, high-quality LV vector stocks is still cumbersome and costly. Methods Here we present a simplified protocol for LV vector production on a laboratory scale using HYPERFlask vessels. HYPERFlask vessels are high-yield, high-performance flasks that utilize a multilayered gas permeable growth surface for efficient gas exchange, allowing convenient production of high-titer LV vectors. For subsequent concentration of LV vector stocks produced in this way, we describe a facile protocol involving Mustang Q anion exchange membrane chromatography. Results Our results show that unconcentrated LV vector stocks with titers in excess of 108 transduction units (TU) per ml were obtained using HYPERFlasks and that these titers were higher than those produced in parallel using regular 150-cm2 tissue culture dishes. We also show that up to 500 ml of an unconcentrated LV vector stock prepared using a HYPERFlask vessel could be concentrated using a single Mustang Q Acrodisc with a membrane volume of 0.18 ml. Up to 5.3 × 1010 TU were recovered from a single HYPERFlask vessel. Conclusion The protocol described here is easy to implement and should facilitate high-titer LV vector production for preclinical studies in animal models without the need for multiple tissue culture dishes and ultracentrifugation-based concentration protocols. PMID:19220915

PLASMA DEVICE

DOEpatents

Baker, W.R.; Brathenahl, A.; Furth, H.P.

1962-04-10

A device for producing a confined high temperature plasma is described. In the device the concave inner surface of an outer annular electrode is disposed concentrically about and facing the convex outer face of an inner annular electrode across which electrodes a high potential is applied to produce an electric field there between. Means is provided to create a magnetic field perpendicular to the electric field and a gas is supplied at reduced pressure in the area therebetween. Upon application of the high potential, the gas between the electrodes is ionized, heated, and under the influence of the electric and magnetic fields there is produced a rotating annular plasma disk. The ionized plasma has high dielectric constant properties. The device is useful as a fast discharge rate capacitor, in controlled thermonuclear research, and other high temperature gas applications. (AEC)

Don't Cry over Spilled Water: Identifying Risks and Solutions for Produced Water Spills

NASA Astrophysics Data System (ADS)

Shores, Amanda Rose

Resource requirements and future energy generation requires careful evaluation, particularly due to climate change and water scarcity. This thesis discusses one aspect of energy generation linked to water; oil-and-gas extraction and the large volumes of waste water produced, otherwise known as "produced water". This research focuses on surface spills of produced water, their ramifications, safeguards against groundwater contamination at spill sites and potential remediation strategies. Produced water contains a variety of contaminants that include the group of known toxins, BTEX (benzene, toluene, ethylbenzene and xylene), and high salt concentrations. A combination of factors such as large volumes of generated produced water, the need for storage and transportation across large distances and the toxic-and-mobile nature of produced water constituents creates risks for spills that can pollute groundwater. Spills occur regularly, particularly in Weld County, Colorado, where the demand for natural gas is high. To answer spill-related hypotheses, a multitude of methodology were employed: modeling, greenhouse experimentation, gas chromatography and summarization of spill reports and statistical analyses. Using publically available spill data, this research found that the frequency of oil-and-gas related spills and the average spilled volume has increased in Weld County from 2011-2015. Additionally, the number of spills that have resulted in groundwater contamination has increased in the area. By focusing on the oil-and-gas operators responsible for these spills, a linear relationship was found between the volumes of oil-and-gas produced compared to the volumes of produced-water generated. However, larger oil-and-gas producers did not show a linear relationship between oil-and-gas produced and produced-water generated, such that larger producers were more efficient and generated less water per unit of energy. So while scale-up efficiency seems to exist for produced-water generation, no mitigation of spill volume would be obtained by utilizing larger producers. Regardless of which operator was responsible for the spill, the groundwater depth at a spill site significantly predicted when a spill would result in groundwater contamination. This result was also validated though modeling; shallow depths to groundwater as well as larger spill volumes and coarse soil textures contributed to higher concentrations of groundwater contamination. Previous research has shown that a large fraction of spills occur at well pads. Our results suggest that fracking-site selection should preclude areas where the groundwater is shallow and soil is coarsely textured. Additionally, precautions should be taken to reduce the volume of spilled produced water to reduce the risk of groundwater contamination. This research additionally sought to reduce contaminant migration in soils towards groundwater at produced-water spill sites. In a greenhouse study it was shown that foxtail barley (Hordeum jubatum) and perennial ryegrass (Lolium perenne), can tolerate high salt concentrations in produced water while taking up minute levels of BTEX. The presence of plants changed the concentration of BTEX and naphthalene in the soil, but the direction of the change depended upon the particular plant and varied across contaminants. Additionally, the roots of either species saw no decrease of biomass upon exposure to BTEX and salt but shoots biomass was significantly reduced for foxtail barley. These results suggest that these grasses would not be capable of addressing large concentrations of BTEX at spill sites; however, these plants would be useful near well pads that regularly experience smaller spills, thus being able to tolerate spills while continually removing small amounts of BTEX in the soil. In conclusion, this thesis sought to identify holistic tools for produced-water spill prevention, mitigation and remediation to lessen environmental and health concerns while creating minimal disturbance to the natural landscape. The results lend themselves to important management information applicable to Weld County, CO but with lessons that others can draw upon elsewhere. This dissertation highlights areas for improved regulation and best management practices that can preemptively reduce the risk for groundwater contamination from produced water spills.

Insecticides: effects on cutthroat trout of repeated exposure to DDT

USGS Publications Warehouse

Allison, Don; Kallman, Burton J.; Cope, Oliver B.; Van Valin, Charles C.

1963-01-01

Cutthroat trout were periodically exposed to p, pp-DDT, in acetone solution or in the food. Excessive mortality occurred only in lots treated with high concentrations of DDT, probably as a result of decreased resistance to nonspecific stressors. Surviving fish in these lots were significantly larger than those in the control lot, or in the lots treated with low concentrations of DDT. The number and volume of eggs produced was not reduced by DDT, but mortality among sac fry appeared to be highest in the lots treated with high concentrations. The data suggest that the sublethal concentrations of DDT ordinarily encountered in the environment are unlikely to damage a fishery.

Role of Melatonin in the Regulation of Differentiation of T Cells Producing Interleukin-17 (Th17).

PubMed

Kuklina, E M; Glebezdina, N S; Nekrasova, I V

2016-03-01

We studied the ability of melatonin in physiological and pharmacological concentrations to induce and/or regulate differentiation of T cells producing IL-17 (Th17). This hormone produced the opposite effect on CD4+T cells, which depended on their activation status. Melatonin induced the synthesis of IL-17A by intact T cells, but had little effect on activated cells. Melatonin in high (pharmacological) concentration decreased the intracellular expression of this cytokine under conditions of polyclonal activation. Melatonin had a dose-depended effect. Taking into the fact that Th17 cells play an important role in the immune defense, it can be suggested that the regulation of their activity by melatonin contributes to this process.

Screening of novel bacteria for the 2,3-butanediol production.

PubMed

Kallbach, Malee; Horn, Sonja; Kuenz, Anja; Prüße, Ulf

2017-02-01

Biotechnologically produced 2,3-butanediol (2,3-BDO) is a potential starting material for industrial bulk chemicals such as butadiene or methyl ethyl ketone which are currently produced from fossil feedstocks. So far, the highest 2,3-BDO concentrations have been obtained with risk group 2 microorganisms. In this study, three risk group 1 microorganisms are presented that are so far unknown for an efficient production of 2,3-BDO. The strains Bacillus atrophaeus NRS-213, Bacillus mojavensis B-14698, and Bacillus vallismortis B-14891 were evaluated regarding their ability to produce high 2,3-BDO concentrations with a broad range of different carbon sources. A maximum 2,3-BDO concentration of 60.4 g/L was reached with the strain B. vallismortis B-14891 with an initial glucose concentration of 200 g/L within 55 h in a batch cultivation. Besides glucose, B. vallismortis B-14891 converts 14 different substrates that can be obtained from residual biomass sources to 2,3-BDO. Therefore B. vallismortis B-14891 is a promising candidate for the large-scale production of 2,3-BDO with low-cost substrates.

The clinical pharmacology and dynamics of marihuana cigarette smoking.

PubMed

Perez-Reyes, M; Owens, S M; Di Guiseppi, S

1981-01-01

We have studied the dynamics of marihuana smoking, the plasma concentration of delta 9-tetrahydrocannabinol (THC), and the pharmacologic effects produced by the sequential smoking of two 1% marihuana cigarettes at a 2-hour interval. Three males and three females, experienced marihuana smokers, participated in the study. The results indicate that each subject smoked his or her two cigarettes at a similar rate. The THC plasma concentrations produced by the smoking of the second cigarette were slightly lower than those produced by the first cigarette. The levels of the psychologic "high" caused by the two cigarettes were similar. However, the first cigarette accelerated the heart twice as much as the second cigarette. Between males and females there were marked differences in the rate at which the cigarettes were smoked. In particular, males took more puffs, took them more often, and consumed the cigarettes more rapidly than females. The plasma concentrations of THC, the self-reported psychologic effects, and the heart rate acceleration produced by the smoking of the two cigarettes were identical between the sexes.

Characterization of aerosols produced by cell sorters and evaluation of containment

PubMed Central

Holmes, Kevin L.

2011-01-01

In spite of the recognition by the flow cytometry community of potential aerosol hazards associated with cell sorting, there has been no previous study that has thoroughly characterized the aerosols that can be produced by cell sorters. In this study an Aerodynamic Particle Sizer was used to determine the concentration and aerodynamic diameter of aerosols produced by a FACS Aria II cell sorter under various conditions. Aerosol containment and evacuation was also evaluated using this novel methodology. The results showed that high concentrations of aerosols in the range of 1–3 μm can be produced in fail mode and that with decreased sheath pressure, aerosol concentration decreased and aerodynamic diameter increased. Although the engineering controls of the FACS Aria II for containment were effective, sort chamber evacuation of aerosols following a simulated nozzle obstruction was ineffective. However, simple modifications to the FACS Aria II are described that greatly improved sort chamber aerosol evacuation. The results of this study will facilitate the risk assessment of cell sorting potentially biohazardous samples by providing much needed data regarding aerosol production and containment. PMID:22052694

Solar-thermal reaction processing

DOEpatents

Weimer, Alan W; Dahl, Jaimee K; Lewandowski, Allan A; Bingham, Carl; Raska Buechler, Karen J; Grothe, Willy

2014-03-18

In an embodiment, a method of conducting a high temperature chemical reaction that produces hydrogen or synthesis gas is described. The high temperature chemical reaction is conducted in a reactor having at least two reactor shells, including an inner shell and an outer shell. Heat absorbing particles are included in a gas stream flowing in the inner shell. The reactor is heated at least in part by a source of concentrated sunlight. The inner shell is heated by the concentrated sunlight. The inner shell re-radiates from the inner wall and heats the heat absorbing particles in the gas stream flowing through the inner shell, and heat transfers from the heat absorbing particles to the first gas stream, thereby heating the reactants in the gas stream to a sufficiently high temperature so that the first gas stream undergoes the desired reaction(s), thereby producing hydrogen or synthesis gas in the gas stream.

Molecular mechanisms of ethanol tolerance in Saccharomyces cerevisiae

USDA-ARS?s Scientific Manuscript database

The yeast Saccharomyces cerevisiae is a superb ethanol producer, yet sensitive to ethanol at higher concentrations especially under high gravity or very high gravity fermentation conditions. Although significant efforts have been made to study ethanol-stress response in past decades, molecular mecha...

Improved fermentation performance to produce bioethanol from Gelidium amansii using Pichia stipitis adapted to galactose.

PubMed

Sukwong, Pailin; Ra, Chae Hun; Sunwoo, In Yung; Tantratian, Sumate; Jeong, Gwi-Taek; Kim, Sung-Koo

2018-03-23

This study employed a statistical method to obtain optimal hyper thermal acid hydrolysis conditions using Gelidium amansii (red seaweed) as a source of biomass. The optimal hyper thermal acid hydrolysis using G. amansii as biomass was determined as 12% (w/v) slurry content, 358.3 mM H 2 SO 4 , and temperature of 142.6 °C for 11 min. After hyper thermal acid hydrolysis, enzymatic saccharification was carried out. The total monosaccharide concentration was 45.1 g/L, 72.2% of the theoretical value of the total fermentable monosaccharides of 62.4 g/L based on 120 g dry weight/L in the G. amansii slurry. To increase ethanol production, 3.8 g/L 5-hydroxymethylfurfural (HMF) in the hydrolysate was removed by treatment with 3.5% (w/v) activated carbon for 2 min and fermented with Pichia stipitis adapted to high galactose concentrations via separate hydrolysis and fermentation. With complete HMF removal and the use of P. stipitis adapted to high galactose concentrations, 22 g/L ethanol was produced (yield 0.50). Fermentation with total HMF removal and yeast adapted to high galactose concentrations increased the fermentation performance and decreased the fermentation time from 96 to 36 h compared to traditional fermentation.

Physiological Aβ Concentrations Produce a More Biomimetic Representation of the Alzheimer's Disease Phenotype in iPSC Derived Human Neurons.

PubMed

Berry, Bonnie J; Smith, Alec S T; Long, Christopher J; Martin, Candace C; Hickman, James J

2018-05-22

Alzheimer's disease (AD) is characterized by slow, progressive neurodegeneration leading to severe neurological impairment, but current drug development efforts are limited by the lack of robust, human-based disease models. Amyloid-β (Aβ) is known to play an integral role in AD progression as it has been shown to interfere with neurological function. However, studies into AD pathology commonly apply Aβ to neurons for short durations at nonphysiological concentrations to induce an exaggerated dysfunctional phenotype. Such methods are unlikely to elucidate early stage disease dysfunction, when treatment is still possible, since damage to neurons by these high concentrations is extensive. In this study, we investigated chronic, pathologically relevant Aβ oligomer concentrations to induce an electrophysiological phenotype that is more representative of early AD progression compared to an acute high-dose application in human cortical neurons. The high, acute oligomer dose resulted in severe neuronal toxicity as well as upregulation of tau and phosphorylated tau. Chronic, low-dose treatment produced significant functional impairment without increased cell death or accumulation of tau protein. This in vitro phenotype more closely mirrors the status of early stage neural decline in AD pathology and could provide a valuable tool to further understanding of early stage AD pathophysiology and for screening potential therapeutic compounds.

Study of the effects of focused high-energy boron ion implantation in diamond

NASA Astrophysics Data System (ADS)

Ynsa, M. D.; Agulló-Rueda, F.; Gordillo, N.; Maira, A.; Moreno-Cerrada, D.; Ramos, M. A.

2017-08-01

Boron-doped diamond is a material with a great technological and industrial interest because of its exceptional chemical, physical and structural properties. At modest boron concentrations, insulating diamond becomes a p-type semiconductor and at higher concentrations a superconducting metal at low temperature. The most conventional preparation method used so far, has been the homogeneous incorporation of boron doping during the diamond synthesis carried out either with high-pressure sintering of crystals or by chemical vapour deposition (CVD) of films. With these methods, high boron concentration can be included without distorting significantly the diamond crystalline lattice. However, it is complicated to manufacture boron-doped microstructures. A promising alternative to produce such microstructures could be the implantation of focused high-energy boron ions, although boron fluences are limited by the damage produced in diamond. In this work, the effect of focused high-energy boron ion implantation in single crystals of diamond is studied under different irradiation fluences and conditions. Micro-Raman spectra of the sample were measured before and after annealing at 1000 °C as a function of irradiation fluence, for both superficial and buried boron implantation, to assess the changes in the diamond lattice by the creation of vacancies and defects and their degree of recovery after annealing.

In vitro growth and maturation of isolated caprine preantral follicles: Influence of insulin and FSH concentration, culture dish, coculture, and oocyte size on meiotic resumption.

PubMed

Silva, G M; Brito, I R; Sales, A D; Aguiar, F L N; Duarte, A B G; Araújo, V R; Vieira, L A; Magalhães-Padilha, D M; Lima, L F; Alves, B G; Silveira, L B R; Lo Turco, E G; Rodrigues, A P; Campello, C C; Wheeler, M B; Figueiredo, J R

2017-03-01

The aims of this study were: (1) to evaluate the effect of different insulin concentrations, alone or in combination with either a fixed FSH concentration or increasing FSH concentrations on the in vitro culture of isolated caprine preantral follicles and (2) to analyze the efficiency of two IVM media and maturation culture systems (with or without coculture with in vivo grown oocytes) on the meiosis resumption. Secondary follicles were cultured for 18 days in a basic medium supplemented with low- or high-insulin concentration alone or with a fixed FSH concentration or with increasing FSH concentrations. Oocytes grown in vivo or in vitro were matured alone or cocultured. The high-insulin concentration associated with fixed FSH treatment had higher meiotic resumption rate (P < 0.05) and was the only treatment capable of producing oocytes in metaphase II. The rates of germinal vesicle, germinal vesicle breakdown, metaphase I, metaphase II (MII), meiotic resumption, and oocyte diameter were similar between the maturation media. In conclusion, a basic medium supplemented with 10-μg/mL insulin and 100-μg/mL FSH throughout the culture period improved meiotic resumption rate and produced MII oocytes from caprine preantral follicles cultured in vitro. The MII rate was similar between in vivo and in vitro grown oocytes ≥110 μm. Copyright © 2016 Elsevier Inc. All rights reserved.

Proceedings 43rd Stanford Geothermal Workshop

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simmons, Stuart; Kirby, Stefan; Verplanck, Philip

Herein we summarize the results of an investigation dealing with the concentrations and inventories of strategic, critical and valuable materials (SCVM) in produced fluids from geothermal and hydrocarbon reservoirs (50-250° C) in Nevada and Utah. Water samples were collected from thirty-four production wells across eight geothermal fields, the Uinta Basin oil/gas province in northeast Utah, and the Covenant oil field in southwestern Utah; additional water samples were collected from six hot springs in the Sevier Thermal Belt in southwestern Utah. Most SCVM concentrations in produced waters range from <0.1 to 100 µg/kg; the main exception is lithium, which has concentrationsmore » that range from <1000 to 25,000 ug/kg. Relatively high concentrations of gallium, germanium, scandium, selenium, and tellurium are measured too. Geothermal waters contain very low concentrations of REEs, below analytical detections limits (0.01 µg/kg), but the concentrations of lanthanum, cerium, and europium range from 0.05 to 5 µg/kg in Uinta basin waters. Among the geothermal fields, the Roosevelt Hot Spring reservoir appears to have the largest inventories of germanium and lithium, and Patua appears to have the largest inventories of gallium, scandium, selenium, and tellurium. By comparison, the Uinta basin has larger inventories of gallium. The concentrations of gallium, germanium, lithium, scandium, selenium, and tellurium in produced waters appear to be partly related to reservoir temperature and concentrations of total dissolved salts. The relatively high concentration and large inventory of lithium occurring at Roosevelt Hot Springs may be related to granitic-gneissic crystalline rocks, which host the reservoir. Analyses of calcite scales from Dixie Valley indicate enrichments in cobalt, gallium, gold, palladium, selenium and tellurium, and these metals appear to be depositing at deep levels in production wells due to boiling. Comparisons with SCVM mineral deposits suggest that brines in sedimentary basins, or derived from lacustrine evaporites, enable aqueous transport of gallium, germanium, and lithium.« less

Antioxidant Properties of “Natchez” and “Triple Crown” Blackberries Using Korean Traditional Winemaking Techniques

PubMed Central

Maness, Niels; McGlynn, William

2017-01-01

This research evaluated blackberries grown in Oklahoma and wines produced using a modified traditional Korean technique employing relatively oxygen-permeable earthenware fermentation vessels. The fermentation variables were temperature (21.6°C versus 26.6°C) and yeast inoculation versus wild fermentation. Wild fermented wines had higher total phenolic concentration than yeast fermented wines. Overall, wines had a relatively high concentration of anthocyanin (85–320 mg L−1 malvidin-3-monoglucoside) and antioxidant capacity (9776–37845 µmol Trolox equivalent g−1). “Natchez” berries had a higher anthocyanin concentration than “Triple Crown” berries. Higher fermentation temperature at the start of the winemaking process followed by the use of lower fermentation/storage temperature for aging wine samples maximized phenolic compound extraction/retention. The Korean winemaking technique used in this study produced blackberry wines that were excellent sources of polyphenolic compounds as well as being high in antioxidant capacity as measured by the Oxygen Radical Absorbance Capacity (ORAC) test. PMID:28713820

Effect of Oxygen Tension and Medium Components on Monomer Distribution of Alginate.

PubMed

Kıvılcımdan Moral, Çiğdem; Doğan, Özdemir; Sanin, Faika Dilek

2015-06-01

Alginate is a natural biopolymer composed of mannuronic and guluronic acid monomers. It is produced by algae and some species of Azotobacter and Pseudomonas. This study aims to investigate the effect of dissolved oxygen tension (DOT) and growth medium substrate and calcium concentrations on the monomeric composition of alginate produced by Azotobacter vinelandii ATCC® 9046 in a fermenter. Results showed that alginate production increased with increasing DOT from 1 to 5 %. The highest alginate production was obtained as 4.51 g/L under 20 g/L of sucrose and 50 mg/L of calcium at 5 % DOT. At these conditions, alginate was rich in mannuronic acid (up to 61 %) and it was particularly high at low calcium concentration. On the other hand, at extreme conditions such as high DOT level (10 % DOT) and low sucrose concentration (10 g/L), guluronic acid was dominant (ranging between 65 and 100 %).

Effect of zolpidem on human cytochrome P450 activity, and on transport mediated by P-glycoprotein.

PubMed

von Moltke, Lisa L; Weemhoff, James L; Perloff, Michael D; Hesse, Leah M; Harmatz, Jerold S; Roth-Schechter, Barbara F; Greenblatt, David J

2002-12-01

The influence of high concentrations of zolpidem (100 microM, corresponding to approximately 200 times maximum therapeutic concentrations) on the activity of six human Cytochrome P450 (CYP) enzymes was evaluated in a model system using human liver microsomes. Zolpidem produced negligible or weak inhibition of human CYP1A2, 2B6, 2C9, 2C19, 2D6, and 3A. Transport of rhodamine 123, presumed to be mediated mainly by the energy-dependent efflux transport protein P-glycoprotein, was studied in a cell culture system using a human intestinal cell line. High concentrations of zolpidem (100 microM), exceeding the usual therapeutic range by more than 100-fold, produced only modest impairment of rhodamine 123 transport. The findings indicate that zolpidem is very unlikely to cause clinical drug interactions attributable to impairment of CYP activity or P-gp mediated transport. Copyright 2002 John Wiley & Sons, Ltd.

Hyper-spectral imaging of aircraft exhaust plumes

NASA Astrophysics Data System (ADS)

Bowen, Spencer; Bradley, Kenneth; Gross, Kevin; Perram, Glen; Marciniak, Michael

2008-10-01

An imaging Fourier-transform spectrometer has been used to determine low spatial resolution temperature and chemical species concentration distributions of aircraft jet engine exhaust plumes. An overview of the imaging Fourier transform spectrometer and the methodology of the project is presented. Results to date are shared and future work is discussed. Exhaust plume data from a Turbine Technologies, LTD, SR-30 turbojet engine at three engine settings was collected using a Telops Field-portable Imaging Radiometric Spectrometer Technology Mid-Wave Extended (FIRST-MWE). Although the plume exhibited high temporal frequency fluctuations, temporal averaging of hyper-spectral data-cubes produced steady-state distributions, which, when co-added and Fourier transformed, produced workable spectra. These spectra were then reduced using a simplified gaseous effluent model to fit forward-modeled spectra obtained from the Line-By-Line Radiative Transfer Model (LBLRTM) and the high-resolution transmission (HITRAN) molecular absorption database to determine approximate temperature and concentration distributions. It is theorized that further development of the physical model will produce better agreement between measured and modeled data.

Solid aerosol generator

DOEpatents

Prescott, D.S.; Schober, R.K.; Beller, J.

1992-03-17

An improved solid aerosol generator used to produce a gas borne stream of dry, solid particles of predetermined size and concentration is disclosed. The improved solid aerosol generator nebulizes a feed solution of known concentration with a flow of preheated gas and dries the resultant wet heated aerosol in a grounded, conical heating chamber, achieving high recovery and flow rates. 2 figs.

Improved solid aerosol generator

DOEpatents

Prescott, D.S.; Schober, R.K.; Beller, J.

1988-07-19

An improved solid aerosol generator used to produce a gas borne stream of dry, solid particles of predetermined size and concentration. The improved solid aerosol generator nebulizes a feed solution of known concentration with a flow of preheated gas and dries the resultant wet heated aerosol in a grounded, conical heating chamber, achieving high recovery and flow rates. 2 figs.

The chemistry and beneficial bioactivities of carvacrol (4-isopropyl-2-methylphenol), a component of essential oils produced by aromatic plants and spices

USDA-ARS?s Scientific Manuscript database

Aromatic plants produce organic compounds that may be involved in the defense of plants against phytopathogenic insects, bacteria, fungi, and viruses. One of these compounds called carvacrol that is found in high concentrations in essential oils such as oregano has been reported to exhibit numerous...

Method and source for producing a high concentration of positively charged molecular hydrogen or deuterium ions

DOEpatents

Ehlers, Kenneth W.; Leung, Ka-Ngo

1988-01-01

A high concentration of positive molecular ions of hydrogen or deuterium gas is extracted from a positive ion source having a short path length of extracted ions, relative to the mean free path of the gas molecules, to minimize the production of other ion species by collision between the positive ions and gas molecules. The ion source has arrays of permanent magnets to produce a multi-cusp magnetic field in regions remote from the plasma grid and the electron emitters, for largely confining the plasma to the space therebetween. The ion source has a chamber which is short in length, relative to its transverse dimensions, and the electron emitters are at an even shorter distance from the plasma grid, which contains one or more extraction apertures.

Role of Insulin in Endogenous Hypertriglyceridemia*

PubMed Central

Reaven, Gerald M.; Lerner, Roger L.; Stern, Michael P.; Farquhar, John W.

1967-01-01

Dietary carbohydrate accentuation of endogenous triglyceride production has been studied in 33 patients. A broad and relatively continuous spectrum of steady-state plasma triglyceride concentrations was produced in 31 of the 33 subjects during 3 wk of a high carbohydrate (fat-free) liquid formula diet. Two patients developed plasma triglyceride concentrations in excess of 2000 mg/100 ml, and these were the only patients we have studied in which carbohydrate induction of hypertriglyceridemia seemed to be associated with a defect in endogenous plasma triglyceride removal mechanisms. In the remaining 31 patients the degree of hypertriglyceridemia was highly correlated with the insulin response elicited by the ingestion of the high carbohydrate formula (P < 0.005). No significant correlation existed between fasting plasma triglyceride concentration and either plasma glucose or free fatty acid concentrations after the high carbohydrate diet, nor was the degree of hypertriglyceridemia related to degree of obesity. It is suggested that hypertriglyceridemia in most subjects results from an increase in hepatic triglyceride secretion rate secondary to exaggerated postprandial increases in plasma insulin concentration. Images PMID:6061748

Rapid strain improvement through optimized evolution in the cytostat.

PubMed

Gilbert, Alan; Sangurdekar, Dipen P; Srienc, Friedrich

2009-06-15

Acetate is present in lignocellulosic hydrolysates at growth inhibiting concentrations. Industrial processes based on such feedstock require strains that are tolerant of this and other inhibitors present. We investigated the effect of acetate on Saccharomyces cerevisiae and show that elevated acetate concentrations result in a decreased specific growth rate, an accumulation of cells in the G1 phase of the cell cycle, and an increased cell size. With the cytostat cultivation technology under previously derived optimal operating conditions, several acetate resistant mutants were enriched and isolated in the shortest possible time. In each case, the isolation time was less than 5 days. The independently isolated mutant strains have increased specific growth rates under conditions of high acetate concentrations, high ethanol concentrations, and high temperature. In the presence of high acetate concentrations, the isolated mutants produce ethanol at higher rates and titers than the parental strain and a commercial ethanol producing strain that has been analyzed for comparison. Whole genome microarray analysis revealed gene amplifications in each mutant. In one case, the LPP1 gene, coding for lipid phosphate phosphatase, was amplified. Two mutants contained amplified ENA1, ENA2, and ENA5 genes, which code for P-type ATPase sodium pumps. LPP1 was overexpressed on a plasmid, and the growth data at elevated acetate concentrations suggest that LPP1 likely contributes to the phenotype of acetate tolerance. A diploid cross of the two mutants with the amplified ENA genes grew faster than either individual haploid parent strain when 20 g/L acetate was supplemented to the medium, which suggests that these genes contribute to acetate tolerance in a gene dosage dependent manner. 2009 Wiley Periodicals, Inc.

Total selenium concentrations in canine and feline foods commercially available in New Zealand.

PubMed

Simcock, S E; Rutherford, S M; Wester, T J; Hendriks, W H

2005-02-01

To determine the total selenium concentrations in petfoods commercially available in New Zealand and to establish whether these meet the current minimum recommended requirements of selenium in foods for cats and dogs. Samples (n=89) from petfoods commercially available in New Zealand were analysed for total selenium concentration using a fluorometric method. Data, expressed on a dry matter (DM) basis, were analysed according to petfood type (dog or cat, and wet or dry), predominant flavour (chicken, seafood, chicken and seafood, beef, meat mix, other), manufacturer and country of manufacture. Fifty percent of petfoods purchased for this study were manufactured in Australia, and the remainder were produced in the United States of America (USA), New Zealand or Thailand. Mean total selenium concentrations were similar (0.61-0.80 mg/kg DM) in petfoods produced in Australia, New Zealand and the USA, but higher (mean 3.77 mg/kg DM; p<0.05) in petfoods produced in Thailand. Petfoods produced in Australia, New Zealand and the USA contained a variety of predominant flavours, whereas petfoods from Thailand contained only seafood flavour. Seafood-based flavours had the highest selenium concentrations in both cat and dog foods. Wet and dry dog foods had similar concentrations of selenium to dry cat foods, but wet cat foods had higher and more variable concentrations of selenium than these others (p<0.05). The mean selenium concentrations in cat and dog foods were 1.14 and 0.40 mg/kg DM, respectively, and there were no significant differences between manufacturers. Selenium concentrations in commercial petfoods sold in New Zealand appeared to meet recommended dietary requirements, although the range of concentrations was highly variable. Whether these recommendations are adequate for the maintenance of optimal health in cats and dogs has yet to be determined. Overt selenium deficiency disorders are unlikely in dogs and cats in New Zealand fed commercial petfoods unless the bioavailability of selenium in particular petfoods is low.

Aqueous Rare Earth Element Patterns and Concentration in Thermal Brines Associated With Oil and Gas Production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nye, Charles; Quillinan, Scott Austin; Neupane, Ghanashyam

This study is part of a joint effort by the University of Wyoming (UW) School of Energy Resources (SER), the UW Engineering Department, Idaho National Laboratories (INL), and the United States Geological Survey (USGS) to describe rare earth element concentrations in oil and gas produced waters and in coal-fired power station ash ponds. In this work we present rare earth element (REE) and trace metal behavior in produced water from four Wyoming oil and gas fields and surface ash pond water from two coal-fired power stations. The concentration of REEs in oil and gas produced waters is largely unknown. Formore » example, of the 150,000 entries in the USGS National Produced Waters Geochemical Database less than 5 include data for REEs. Part of the reason for this scarcity is the analytical challenge of measuring REEs in high salinity, hydrocarbon-bearing waters. The industry standard for water analysis struggles to detect REEs in natural waters under ideal conditions. The detection of REEs in oil and gas field samples becomes all but impossible with the background noise and interferences caused by high concentrations of non-REE ions and residual hydrocarbons. The INL team members have overcome many of these challenges (e.g. McLing, 2014), and continue to develop their methods. Using the methods of the INL team members we measured REEs in high salinity oil and gas produced waters. Our results show that REEs exist as a dissolved species in all waters measured for this project, typically within the parts per trillion range. The samples may be grouped into two broad categories analytically, and these categories match their genesis: Wyoming oil and gas brines contain elevated levels of Europium, and Wyoming industrial pond waters show elevation in heavy REEs (HREEs). While broadly true, important variations exist within both groups. In the same field Europium can vary by more than an order of magnitude, and likewise HREEs in industrial ponds at the same site can vary by more than an order of magnitude. Future work will investigate the reasons for these variations.« less

US researchers study effectiveness of Fluidized Sand Biofilters

USDA-ARS?s Scientific Manuscript database

Intensive aquaculture facilities generally produce two separate waste flows: 1) a high volume dilute discharge from culture tanks or pump sumps, and 2) a moderately small and solids-concentrated discharge typically backwashed from mechanical filtration units. The high volume dilute flow can appear p...

Hydrocarbons from spirulina pyrolysis bio-oil using one-step hydrotreating and aqueous extraction of heteroatom compounds

USDA-ARS?s Scientific Manuscript database

Biomass feedstocks such as algae and cyanobacteria are highly sought after due to their high reproduction rates and growth densities, but their high concentrations of O and N heteroatoms are problematic for biofuels applications. The development of mild upgrading processes is necessary for producing...

Rheological Behavior of Tomato Fiber Suspensions Produced by High Shear and High Pressure Homogenization and Their Application in Tomato Products

PubMed Central

Sun, Ping; Adhikari, Benu P.; Li, Dong

2018-01-01

This study investigated the effects of high shear and high pressure homogenization on the rheological properties (steady shear viscosity, storage and loss modulus, and deformation) and homogeneity in tomato fiber suspensions. The tomato fiber suspensions at different concentrations (0.1%–1%, w/w) were subjected to high shear and high pressure homogenization and the morphology (distribution of fiber particles), rheological properties, and color parameters of the homogenized suspensions were measured. The homogenized suspensions were significantly more uniform compared to unhomogenized suspension. The homogenized suspensions were found to better resist the deformation caused by external stress (creep behavior). The apparent viscosity and storage and loss modulus of homogenized tomato fiber suspension are comparable with those of commercial tomato ketchup even at the fiber concentration as low as 0.5% (w/w), implying the possibility of using tomato fiber as thickener. The model tomato sauce produced using tomato fiber showed desirable consistency and color. These results indicate that the application of tomato fiber in tomato-based food products would be desirable and beneficial. PMID:29743890

Simplified method for preparation of concentrated exoproteins produced by Staphylococcus aureus grown on surface of cellophane bag containing liquid medium.

PubMed

Ikigai, H; Seki, K; Nishihara, S; Masuda, S

1988-01-01

A simplified method for preparation of concentrated exoproteins including protein A and alpha-toxin produced by Staphylococcus aureus was successfully devised. The concentrated proteins were obtained by cultivating S. aureus organisms on the surface of a liquid medium-containing cellophane bag enclosed in a sterilized glass flask. With the same amount of medium, the total amount of proteins obtained by the method presented here was identical with that obtained by conventional liquid culture. The concentration of proteins obtained by the method, however, was high enough to observe their distinct bands stained on polyacrylamide gel electrophoresis. This method was considered quite useful not only for large-scale cultivation for the purification of staphylococcal proteins but also for small-scale study using the proteins. The precise description of the method was presented and its possible usefulness was discussed.

Relevance of Chemical Kinetics for Medicine: The Case of Nitric Oxide

NASA Astrophysics Data System (ADS)

Balaban, Alexandru T.; Seitz, William

2003-06-01

Nitric oxide, NO, is central to many physiological processes including regulation of blood pressure and nerve signal transmission. Enzymes in endothelial cells and in the brain of mammals continuously synthesize it—generally in low and carefully regulated concentrations. The well known reaction of NO with oxygen to produce toxic nitrogen dioxide, NO2, has a rate which is bimolecular in NO. High concentrations of NO, as are found often in industrial plants or cigarettes, react rapidly with oxygen to produce toxic NO2. However, the half-life of NO at low NO concentrations as found in solutions and gases occurring in blood vessels, brains, and lungs is sufficiently long for biochemical purposes. Kinetics, then, determines the harmful versus helpful aspects of nitric oxide. At concentrations below 80 ppm NO is used in hospitals for lung vasodilation of preterm newborns and patients with pulmonary distress.

Dynamic superconcentration at critical-point double-layer gates of conducting nanoporous granules due to asymmetric tangential fluxes

PubMed Central

Wang, Shau-Chun; Wei, Hsien-Hung; Chen, Hsiao-Ping; Tsai, Min-Hsuan; Yu, Chun-Ching; Chang, Hsueh-Chia

2008-01-01

A transient 106-fold concentration of double-layer counterions by a high-intensity electric field is demonstrated at the exit pole of a millimeter-sized conducting nanoporous granule that permits ion permeation. The phenomenon is attributed to a unique counterion screening dynamics that transforms half of the surface field into a converging one toward the ejecting pole. The resulting surface conduction flux then funnels a large upstream electro-osmotic convective counterion flux into the injecting hemisphere toward the zero-dimensional gate of the ejecting hemisphere to produce the superconcentration. As the concentrated counterion is ejected into the electroneutral bulk electrolyte, it attracts co-ions and produce a corresponding concentration of the co-ions. This mechanism is also shown to trap and concentrate co-ion microcolloids of micron sizes too (macroions) and hence has potential application in bead-based molecular assays. PMID:19693364

Photoactivation of PBFA-2

NASA Astrophysics Data System (ADS)

Simmons, T. N.; Mashburn, J. B.

A 30 MV peak output voltage will be produced. A substantial portion of the output energy will be lost as free electrons which produce hard X-rays. Many X-rays will have energies within the photoneutron giant resonance. A PBFA-2 shot will produce about 5 x 10 E14 photoneutrons. These photoneutron reactions will induce radioactivity in and about PBFA-2. Activation structural components in the center section will be limited by substituting aluminum for stainless steel in regions of high X-ray intensity. Air will be activated above and below the center section after shots; however, X-ray shielding will limit initial concentrations to five times health guidelines. The short half-lives of air radioactivity will permit reentry following simple decay without ventilation. Some radioactive material will be eroded by arcing, but the resulting contamination whould be small. Miniscule concentrations of radioactivity will be produced in the water surrounding the center section.

Spatially Resolved Temperature and Water Vapor Concentration Distributions in Supersonic Combustion Facilities by TDLAT

NASA Technical Reports Server (NTRS)

Busa, K. M.; McDaniel J. C.; Diskin, G. S.; DePiro, M. J.; Capriotti, D. P.; Gaffney, R. L.

2012-01-01

Detailed knowledge of the internal structure of high-enthalpy flows can provide valuable insight to the performance of scramjet combustors. Tunable Diode Laser Absorption Spectroscopy (TDLAS) is often employed to measure temperature and species concentration. However, TDLAS is a path-integrated line-of-sight (LOS) measurement, and thus does not produce spatially resolved distributions. Tunable Diode Laser Absorption Tomography (TDLAT) is a non-intrusive measurement technique for determining two-dimensional spatially resolved distributions of temperature and species concentration in high enthalpy flows. TDLAT combines TDLAS with tomographic image reconstruction. More than 2500 separate line-of-sight TDLAS measurements are analyzed in order to produce highly resolved temperature and species concentration distributions. Measurements have been collected at the University of Virginia's Supersonic Combustion Facility (UVaSCF) as well as at the NASA Langley Direct-Connect Supersonic Combustion Test Facility (DCSCTF). Due to the UVaSCF s unique electrical heating and ability for vitiate addition, measurements collected at the UVaSCF are presented as a calibration of the technique. Measurements collected at the DCSCTF required significant modifications to system hardware and software designs due to its larger measurement area and shorter test duration. Tomographic temperature and water vapor concentration distributions are presented from experimentation on the UVaSCF operating at a high temperature non-reacting case for water vitiation level of 12%. Initial LOS measurements from the NASA Langley DCSCTF operating at an equivalence ratio of 0.5 are also presented. Results show the capability of TDLAT to adapt to several experimental setups and test parameters.

Scalable Production Method for Graphene Oxide Water Vapor Separation Membranes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fifield, Leonard S.; Shin, Yongsoon; Liu, Wei

ABSTRACT Membranes for selective water vapor separation were assembled from graphene oxide suspension using techniques compatible with high volume industrial production. The large-diameter graphene oxide flake suspensions were synthesized from graphite materials via relatively efficient chemical oxidation steps with attention paid to maintaining flake size and achieving high graphene oxide concentrations. Graphene oxide membranes produced using scalable casting methods exhibited water vapor flux and water/nitrogen selectivity performance meeting or exceeding that of membranes produced using vacuum-assisted laboratory techniques. (PNNL-SA-117497)

Production of Neutral Beams from Negative Ion Beam Systems in the USSR

DTIC Science & Technology

1982-12-01

research is to produce long-pulse and CW high-energy neutral beams. The Oak Ridge National Laboratory ( ORNL ) has been concentrating on the direct extraction...next generation of mirror devices [1II. ORNL is using a cesium converter to produce negative ions from low-energy positive ions from a duopigatron ion...with Formation of Highly Excited Hydrogen Atoms," ZhTF, Vol. 36, No. 7, 1966, p. 1241 . 107. Kartashev, K. B., V. I. Pistunovich, V. V. Platonov, V. D

The mineralogy of bauxite for producing smelter-grade alumina

NASA Astrophysics Data System (ADS)

Authier-Martin, M.; Forte, G.; Ostap, S.; See, J.

2001-12-01

Aluminum-producing companies rely on low-cost, high-purity, smelter-grade alumina (aluminum oxide), and alumina production utilizes the bulk of bauxites mined world-wide. The mineralogy of the bauxites has a significant impact on the operation of the Bayer process for alumina production. Typically, the Bayer process produces smelter-grade alumina of 99.5% Al2O3, starting from bauxite containing 30% to 60% Al2O3. The main objective of the Bayer process is to extract the maximum amount of aluminum from the bauxite at as high an aluminate concentration in solution as possible, while limiting any troublesome side reactions. Only with a better understanding of the chemistry of the mineral species and a strict control of the operating/processing conditions can the Bayer process produce efficiently, a low cost, high-quality alumina with minimum detrimental environmental impact.

Brassicaceae tissues as inhibitors of nitrification in soil.

PubMed

Brown, Paul D; Morra, Matthew J

2009-09-09

Brassicaceae crops often produce an unexplained increase in plant-available soil N possibly related to bioactive compounds produced from glucosinolates present in the tissues. Our objective was to determine if glucosinolate-containing tissues inhibit nitrification, thereby potentially explaining this observation. Ammonium, NO(2)(-), and NO(3)(-) N were measured in soils amended with Brassicaceae ( Isatis tinctoria L., Brassica napus L., Brassica juncea L., and Sinapis alba L.) tissues containing different glucosinolate types and concentrations or Kentucky bluegrass ( Poa pratensis L.) residues with equivalent C/N ratios as the Brassicaceae samples. There was greater accumulation of NH(4)(+) N in soils amended with tissues containing high glucosinolate concentrations as compared to soils amended with tissues containing no or low glucosinolate concentrations. Nitrite N was detected only in soils amended with Brassicaceae tissues having the highest glucosinolate concentrations. The positive correlation of both NH(4)(+) and NO(2)(-) N accumulation with the glucosinolate concentration indicates the participation of glucosinolate hydrolysis products in nitrification inhibition.

The revised edition of korean calendar for allergenic pollens.

PubMed

Oh, Jae-Won; Lee, Ha-Baik; Kang, Im-Joo; Kim, Seong-Won; Park, Kang-Seo; Kook, Myung-Hee; Kim, Bong-Seong; Baek, Hey-Sung; Kim, Joo-Hwa; Kim, Ja-Kyung; Lee, Dong-Jin; Kim, Kyu-Rang; Choi, Young-Jin

2012-01-01

The old calendar of pollens did not reflect current pollen distribution and concentrations that can be influenced by changes of weather and environment of each region in South Korea. A new pollen calendar of allergenic pollens was made based on the data on pollen concentrations obtained in eight regions nationwide between 1997 and 2009. The distribution of pollen was assessed every day at 8 areas (Seoul, Guri, Busan, Daegu, Jeonju, Kwangju, Kangneung, and Jeju) for 12 years between July 1, 1997 and June 30, 2009. Pollens were collected by using Burkard 7-day sampler (Burkard Manufacturing Co Ltd, UK). Pollens which were stained with Calberla's fuchsin staining solution were identified and counted. Pine became the highest pollen in May, and the pollen concentrations of oak and birch also became high. Ragweed appeared in the middle of August and showed the highest pollen concentration in the middles of September. Japanese hop showed a high concentration between the middle of August and the end of September, and mugwort appeared in the middles of August and its concentration increased up until early September. In Kangneung, birch appeared earlier, pine showed a higher pollen concentration than in the other areas. In Daegu, Oriental thuja and alder produced a large concentration of pollens. Pine produced a large concentration of pollens between the middle of April and the end of May. Weeds showed higher concentrations in September and mugwort appeared earlier than ragweed. In Busan the time of flowering is relatively early, and alder and Oriental thuja appeared earliest among all areas. In Kwangju, Oriental thuja and hazelnut appeared in early February. Japanese cedar showed the highest pollen concentration in March in Jeju. In conclusion, update information on pollen calendar in South Korea should be provided for allergic patients through the website to manage and prevent the pollinosis.

Characterization of Aerosols of Titanium Dioxide Nanoparticles Following Three Generation Methods Using an Optimized Aerosolization System Designed for Experimental Inhalation Studies

PubMed Central

Pujalté, Igor; Serventi, Alessandra; Noël, Alexandra; Dieme, Denis; Haddad, Sami; Bouchard, Michèle

2017-01-01

Nanoparticles (NPs) can be released in the air in work settings, but various factors influence the exposure of workers. Controlled inhalation experiments can thus be conducted in an attempt to reproduce real-life exposure conditions and assess inhalation toxicology. Methods exist to generate aerosols, but it remains difficult to obtain nano-sized and stable aerosols suitable for inhalation experiments. The goal of this work was to characterize aerosols of titanium dioxide (TiO2) NPs, generated using a novel inhalation system equipped with three types of generators—a wet collision jet nebulizer, a dry dust jet and an electrospray aerosolizer—with the aim of producing stable aerosols with a nano-diameter average (<100 nm) and monodispersed distribution for future rodent exposures and toxicological studies. Results showed the ability of the three generation systems to provide good and stable dispersions of NPs, applicable for acute (continuous up to 8 h) and repeated (21-day) exposures. In all cases, the generated aerosols were composed mainly of small aggregates/agglomerates (average diameter <100 nm) with the electrospray producing the finest (average diameter of 70–75 mm) and least concentrated aerosols (between 0.150 and 2.5 mg/m3). The dust jet was able to produce concentrations varying from 1.5 to 150 mg/m3, and hence, the most highly concentrated aerosols. The nebulizer collision jet aerosolizer was the most versatile generator, producing both low (0.5 mg/m3) and relatively high concentrations (30 mg/m3). The three optimized generators appeared suited for possible toxicological studies of inhaled NPs. PMID:29051446

Efficient cell-free production of olfactory receptors: detergent optimization, structure, and ligand binding analyses.

PubMed

Kaiser, Liselotte; Graveland-Bikker, Johanna; Steuerwald, Dirk; Vanberghem, Mélanie; Herlihy, Kara; Zhang, Shuguang

2008-10-14

High-level production of membrane proteins, particularly of G protein-coupled receptors (GPCRs) in heterologous cell systems encounters a number of difficulties from their inherent hydrophobicity in their transmembrane domains, which frequently cause protein aggregation and cytotoxicity and thus reduce the protein yield. Recent advances in cell-free protein synthesis circumvent those problems to produce membrane proteins with a yield sometimes exceeding the cell-based approach. Here, we report cell-free production of a human olfactory receptor 17-4 (hOR17-4) using the wheat germ extract. Using the simple method, we also successful produced two additional olfactory receptors. To obtain soluble olfactory receptors and to increase yield, we directly added different detergents in varying concentrations to the cell-free reaction. To identify a purification buffer system that maintained the receptor in a nonaggregated form, we developed a method that uses small-volume size-exclusion column chromatography combined with rapid and sensitive dot-blot detection. Different buffer components including salt concentration, various detergents and detergent concentration, and reducing agent and its concentrations were evaluated for their ability to maintain the cell-free produced protein stable and nonaggregated. The purified olfactory receptor displays a typical a alpha-helical CD spectrum. Surface plasmon resonance measurements were used to show binding of a known ligand undecanal to hOR17-4. Our approach to produce a high yield of purified olfactory receptor is a milestone toward obtaining a large quantity of olfactory receptors for designing bionic sensors. Furthermore, this simple approach may be broadly useful not only for other classes of GPCRs but also for other membrane proteins.

Efficient cell-free production of olfactory receptors: Detergent optimization, structure, and ligand binding analyses

PubMed Central

Kaiser, Liselotte; Graveland-Bikker, Johanna; Steuerwald, Dirk; Vanberghem, Mélanie; Herlihy, Kara; Zhang, Shuguang

2008-01-01

High-level production of membrane proteins, particularly of G protein-coupled receptors (GPCRs) in heterologous cell systems encounters a number of difficulties from their inherent hydrophobicity in their transmembrane domains, which frequently cause protein aggregation and cytotoxicity and thus reduce the protein yield. Recent advances in cell-free protein synthesis circumvent those problems to produce membrane proteins with a yield sometimes exceeding the cell-based approach. Here, we report cell-free production of a human olfactory receptor 17-4 (hOR17-4) using the wheat germ extract. Using the simple method, we also successful produced two additional olfactory receptors. To obtain soluble olfactory receptors and to increase yield, we directly added different detergents in varying concentrations to the cell-free reaction. To identify a purification buffer system that maintained the receptor in a nonaggregated form, we developed a method that uses small-volume size-exclusion column chromatography combined with rapid and sensitive dot-blot detection. Different buffer components including salt concentration, various detergents and detergent concentration, and reducing agent and its concentrations were evaluated for their ability to maintain the cell-free produced protein stable and nonaggregated. The purified olfactory receptor displays a typical a α-helical CD spectrum. Surface plasmon resonance measurements were used to show binding of a known ligand undecanal to hOR17-4. Our approach to produce a high yield of purified olfactory receptor is a milestone toward obtaining a large quantity of olfactory receptors for designing bionic sensors. Furthermore, this simple approach may be broadly useful not only for other classes of GPCRs but also for other membrane proteins. PMID:18840687

Dependence of Initial Oxygen Concentration on Ozone Yield Using Inductive Energy Storage System Pulsed Power Generator

NASA Astrophysics Data System (ADS)

Go, Tomio; Tanaka, Yasushi; Yamazaki, Nobuyuki; Mukaigawa, Seiji; Takaki, Koichi; Fujiwara, Tamiya

Dependence of initial oxygen concentration on ozone yield using streamer discharge reactor driven by an inductive energy storage system pulsed power generator is described in this paper. Fast recovery type diodes were employed as semiconductor opening switch to interrupt a circuit current within 100 ns. This rapid current change produced high-voltage short pulse between a secondary energy storage inductor. The repetitive high-voltage short pulse was applied to a 1 mm diameter center wire electrode placed in a cylindrical pulse corona reactor. The streamer discharge successfully occurred between the center wire electrode and an outer cylinder ground electrode of 2 cm inner diameter. The ozone was produced with the streamer discharge and increased with increasing pulse repetition rate. The ozone yield changed in proportion to initial oxygen concentration contained in the injected gas mixture at 800 ns forward pumping time of the current. However, the decrease of the ozone yield by decreasing oxygen concentration in the gas mixture at 180 ns forward pumping time of the current was lower than the decrease at 800 ns forward pumping time of the current. This dependence of the initial oxygen concentration on ozone yield at 180 ns forward pumping time is similar to that of dielectric barrier discharge reactor.

Oily wastewaters treatment using Pseudomonas sp. isolated from the compost fertilizer

PubMed Central

2014-01-01

Background Discharging the oily wastewater in the environment causes serious problems, because of the oil compounds and organic materials presence. Applying biological methods using the lipase enzyme producer microorganisms can be an appropriate choice for treatment of these wastewaters. The aim of this study is to treat those oil wastewaters having high concentration of oil by applying lipase enzyme producer bacteria. Materials and methods Oil concentration measurement was conducted using the standard method of gravimetric and the wastewater under study was synthetically made and contained olive, canola and sunflower oil. The strain used in this study was Pseudomonas strain isolated from compost fertilizer. The oil under study had concentration of 1.5 to 22 g/l. Results The oil removal amount in concentrations lower than 8.4 g/l was over 95 ± 1.5%. Increase of the oil's concentration to 22 g/l decreases the amount of removal in retention time of 44 hours to 85 ± 2.5%. The best yield of removing this strain in retention time of 44 hours and temperature of 30°C was achieved using Ammonium Nitrate as the nitrogen resource which yield was about 95 percent. Conclusion The findings of the research showed that Pseudomonas bacteria isolated from the compost fertilizer can degrade high concentration oils. PMID:24876932

Water reclamation during drinking water treatments using polyamide nanofiltration membranes on a pilot scale.

PubMed

Kukučka, Miroslav; Kukučka, Nikoleta; Habuda-Stanić, Mirna

2016-09-01

The aim of this study was to investigate the performances of polyamide nanofiltration membranes during water reclamation. The study was conducted using nanofiltration concentrates obtained from two different nanofiltration drinking water treatment plants placed in the northern part of Serbia (Kikinda and Zrenjanin). Used nanofiltration concentrates contained high concentrations of arsenic (45 and 451 μg/L) and natural organic matter (43.1 and 224.40 mgKMnO4/L). Performances of polyamide nanofiltration membranes during water reclamation were investigated under various fluxes and transmembrane pressures in order to obtain drinking water from nanofiltration concentrates and, therefore, reduce the amount of produced concentrates and minimize the waste that has to be discharged in the environment. Applied polyamide nanofiltration membranes showed better removal efficiency during water reclamation when the concentrate with higher content of arsenic and natural organic matter was used while the obtained permeates were in accordance with European regulations. This study showed that total concentrate yield can be reduced to ~5 % of the optimum flux value, in both experiments. The obtained result for concentrate yield under the optimum flux presents considerable amount of reclaimed drinking water and valuable reduced quantity of produced wastewater.

Comparison of biotransformation of inorganic selenium by Lactobacillus and Saccharomyces in lactic fermentation process of yogurt and kefir.

PubMed

Alzate, A; Fernández-Fernández, A; Pérez-Conde, M C; Gutiérrez, A M; Cámara, C

2008-09-24

The aim of the present study was to characterize, quantify, and compare the different selenium species that are produced when lactic fermentation with two different types of microorganisms, bacteria (Lactobacillus) and yeast (Saccharomyces), take place to produce yogurt and kefir, respectively, and to study the transformation process of these species as a function of time. These two dairy products were chosen for the study because they are highly consumed in different cultures. Moreover, the microorganisms present in the fermentation processes are different. While the bacteria Lactobacillus is the one responsible for yogurt fermentation, a partnership between bacteria and the yeast Saccharomyces causes kefir fermentation. A comparative study has been carried out by fermenting Se(IV) enriched milk in the presence of both types of microorganisms, where the concentration range studied was from 0.5 to 20 microg g (-1). Enzymatic extraction enabled selenium speciation profiles, obtained by anionic exchange and ion-pairing reversed phase high performance liquid chromatography (IP-RP-HPLC) with inductively coupled plasma mass spectrometry (ICP-MS) detection. Scanning electron microscopy (SEM) applied to the enriched samples showed segregated Se (0), at added concentrations higher than 5 microg g (-1). The main Se species formed depended on the type of microorganism involved in the fermentation process, SeCys 2 and MeSeCys being the main species generated in yogurt and SeMet in kefir. The results obtained are different for both kinds of samples. Lactic fermentation for yogurt produced an increment in selenocystine (SeCys 2) and Se-methylselenocysteine (MeSeCys), while fermentation to produce kefir also incremented the selenomethionine (SeMet) concentration. The Se species are stable for at least 10 and 15 days for kefir and yogurt, respectively. After this period, selenocystine concentration decreased, and the concentration of Se-methylselenocysteine was found to significantly increase.

Wintertime Emissions from Produced Water Ponds

NASA Astrophysics Data System (ADS)

Evans, J.; Lyman, S.; Mansfield, M. L.

2013-12-01

Every year oil and gas drilling in the U.S. generates billions of barrels of produced water (water brought to the surface during oil or gas production). Efficiently disposing of produced water presents a constant financial challenge for producers. The most noticeable disposal method in eastern Utah's Uintah Basin is the use of evaporation ponds. There are 427 acres of produced water ponds in the Uintah Basin, and these were used to evaporate more than 5 million barrels of produced water in 2012, 6% of all produced water in the Basin. Ozone concentrations exceeding EPA standards have been observed in the Uintah Basin during winter inversion conditions, with daily maximum 8 hour average concentrations at some research sites exceeding 150 parts per billion. Produced water contains ozone-forming volatile organic compounds (VOC) which escape into the atmosphere as the water is evaporated, potentially contributing to air quality problems. No peer-reviewed study of VOC emissions from produced water ponds has been reported, and filling this gap is essential for the development of accurate emissions inventories for the Uintah Basin and other air sheds with oil and gas production. Methane, carbon dioxide, and VOC emissions were measured at three separate pond facilities in the Uintah Basin in February and March of 2013 using a dynamic flux chamber. Pond emissions vary with meteorological conditions, so measurements of VOC emissions were collected during winter to obtain data relevant to periods of high ozone production. Much of the pond area at evaporation facilities was frozen during the study period, but areas that actively received water from trucks remained unfrozen. These areas accounted for 99.2% of total emissions but only 9.5% of the total pond area on average. Ice and snow on frozen ponds served as a cap, prohibiting VOC from being emitted into the atmosphere. Emissions of benzene, toluene, and other aromatic VOCs averaged over 150 mg m-2 h-1 from unfrozen pond surfaces. These compounds are highly reactive and, because of their relatively high water solubility, tend to concentrate in produced water. The average methanol emission rate from unfrozen pond surfaces was more than 100 mg m-2 h-1. Methanol, used as an antifreeze and anti-scaler in the oil and gas industry, is abundant during winter inversions in the Uintah Basin and may also be a significant precursor to ozone production. Total VOC and methanol emissions from produced water ponds during winter were estimated to be 178 and 83 tons month-1, respectively, for the entire Uintah Basin.

Evaluation of Non-Saccharomyces Yeasts for the Reduction of Alcohol Content in Wine

PubMed Central

Contreras, A.; Hidalgo, C.; Henschke, P. A.; Chambers, P. J.; Curtin, C.

2014-01-01

Over recent decades, the average ethanol concentration of wine has increased, largely due to consumer preference for wine styles associated with increased grape maturity; sugar content increases with grape maturity, and this translates into increased alcohol content in wine. However, high ethanol content impacts wine sensory properties, reducing the perceived complexity of flavors and aromas. In addition, for health and economic reasons, the wine sector is actively seeking technologies to facilitate the production of wines with lower ethanol content. Nonconventional yeast species, in particular, non-Saccharomyces yeasts, have shown potential for producing wines with lower alcohol content. These yeast species, which are largely associated with grapes preharvest, are present in the early stages of fermentation but, in general, are not capable of completing alcoholic fermentation. We have evaluated 50 different non-Saccharomyces isolates belonging to 24 different genera for their capacity to produce wine with a lower ethanol concentration when used in sequential inoculation regimes with a Saccharomyces cerevisiae wine strain. A sequential inoculation of Metschnikowia pulcherrima AWRI1149 followed by an S. cerevisiae wine strain was best able to produce wine with an ethanol concentration lower than that achieved with the single-inoculum, wine yeast control. Sequential fermentations utilizing AWRI1149 produced wines with 0.9% (vol/vol) and 1.6% (vol/vol) (corresponding to 7.1 g/liter and 12.6 g/liter, respectively) lower ethanol concentrations in Chardonnay and Shiraz wines, respectively. In Chardonnay wine, the total concentration of esters and higher alcohols was higher for wines generated from sequential inoculations, whereas the total concentration of volatile acids was significantly lower. In sequentially inoculated Shiraz wines, the total concentration of higher alcohols was higher and the total concentration of volatile acids was reduced compared with those in control S. cerevisiae wines, whereas the total concentrations of esters were not significantly different. PMID:24375129

Treatment of biomass to obtain ethanol

DOEpatents

Dunson, Jr., James B.; Elander, Richard T [Evergreen, CO; Tucker, III, Melvin P.; Hennessey, Susan Marie [Avondale, PA

2011-08-16

Ethanol was produced using biocatalysts that are able to ferment sugars derived from treated biomass. Sugars were obtained by pretreating biomass under conditions of high solids and low ammonia concentration, followed by saccharification.

EFFECTS OF CADMIUM AND ZINC ON THE OVARIAN MATURATION AND HEMOLYMPH VITELLOGENIN CONCENTRATIONS OF PROCAMBARUS CLARKII: LABORATORY SIMULATION OF THE AZNALCOLLAR MINING SPILL.

EPA Science Inventory

The Aznalcollar mining spill contaminated the nearby Guadiamar river that flows into the Guadalquivir Estuary. The mining accident produced almost 6 Hm3 of mud and acidic waters, with high concentrations of metals in solution including Cd, Cu, Mn, As, Pb and especially Zn. As a ...

Antioxidant Effect of Polyoxidonium and Metaprot during Bronchopulmonary Inflammation in Rats.

PubMed

Zarubina, I V; Shabanov, P D

2015-12-01

The antioxidant effects of individual or combined application of polyoxidonium and metaprot were examined in rats with acute bronchopulmonary inflammation. By degree of antioxidant potency, polyoxidonium was inferior to metaprot, but their combined application produced more potent antioxidant effect. Polyoxidonium and metaprot in low concentrations increased and in high concentrations suppressed spontaneous biochemiluminescence in the model system of alveolar macrophages.

[Pollutants produced in municipal refuse container during transfer process].

PubMed

Wang, Xiao-Yuan; Liu, Yin-Hua; Wang, Fei; Huang, Chang-Ying; Lu, Feng; Xie, Bing

2014-05-01

The generation and variation of the secondary pollutants in containers during seasons of a year were investigated in a municipal refuse transfer station of Shanghai. The results showed that the primary odors, the concentration of H2S was in a range of 0.3-10.3 mg.m-3, CH4 was in a range of 0.02% -2.97% and NH3 was in a range of 0.7-4.5 mg m-3, and their concentrations all reached the peak in the summer. The pH of the leachate was in a range of 5.4-6. 3, COD was 41 633-84 060 mgL- 1, and BOD, was 18 116-34 130 mg.L , the concentration of pollutants were all higher in winter than that in summer. The ammonia concentration of leachate was in a range of 537-1222 mg.L'', while the TP fluctuated acutely in a range of 17.98-296 mg L-1, exhibiting the relationship with seasonal variation. Extreme temperatures especially the high temperature in summer significantly affected air pollution producing, which indicated that containers should be kept against high temperature exposure and long residence time in order to prevent flammable gases and other pollutants generated largely.

Assessment of selenium bioavailability from naturally produced high-selenium soy foods in selenium-deficient rats.

PubMed

Yan, Lin; Reeves, Philip G; Johnson, LuAnn K

2010-10-01

We assessed the bioavailability of selenium (Se) from a protein isolate and tofu (bean curd) prepared from naturally produced high-Se soybeans. The Se concentrations of the soybeans, the protein isolate and tofu were 5.2±0.2, 11.4±0.1 and 7.4±0.1mg/kg, respectively. Male weanling Sprague-Dawley rats were depleted of Se by feeding them a 30% Torula yeast-based diet (4.1μg Se/kg) for 56 days, and then they were replenished with Se for an additional 50 days by feeding them the same diet containing 14, 24 or 30 μg Se/kg from the protein isolate or 13, 23 or 31 μg Se/kg from tofu, respectively. l-Selenomethionine (SeMet) was used as a reference. Selenium bioavailability was determined on the basis of the restoration of Se-dependent enzyme activities and tissue Se concentrations in Se-depleted rats, comparing those responses for the protein isolate and tofu to those for SeMet by using a slope-ratio method. Dietary supplementation with the protein isolate or tofu resulted in linear or log-linear, dose-dependent increases in glutathione peroxidase activities in blood and liver and in thioredoxin reductase activity in liver. Furthermore, supplementation with the protein isolate or tofu resulted in linear or log-linear, dose-dependent increases in the Se concentrations of plasma, liver, muscle and kidneys. These results indicated an overall bioavailability of approximately 101% for Se from the protein isolate and 94% from tofu, relative to SeMet. We conclude that Se from naturally produced high-Se soybeans is highly bioavailable in this model and that high-Se soybeans may be a good dietary source of Se. Published by Elsevier GmbH.

Airborne bio-aerosols and noise in a dry waste treatment plant in Pietarsaari, Finland.

PubMed

Tolvanen, O K

2001-04-01

Ewapower Ltd in Pietarsaari, Finland produces pellets from paper and plastic waste for burning. During 1998 and 1999, several measurements were made to determine the dust, particle, microbe and endotoxin concentrations, and also the noise level in the hall where the waste is received and pre-crushed. The noise level exceeded the Finnish recommended level of 85 dBA. The dust and the particle concentrations were low, but the microbe concentrations, especially in the summer and in the autumn, were at a level which may be harmful to health. The total concentration of microbes (both dead and alive) was high--approximately 4.8 million particles m(-3). The concentrations of endotoxins was high in summer and in autumn, from 340 to 1000 ng m(-3) and exceeded recommended values. In the winter, the concentration of the endotoxin was lower, ranging between 4.7 and 33 ng m(-3).

Enhanced phytoextraction: II. Effect of EDTA and citric acid on heavy metal uptake by Helianthus annuus from a calcareous soil.

PubMed

Lesage, E; Meers, E; Vervaeke, P; Lamsal, S; Hopgood, M; Tack, F M G; Verloo, M G

2005-01-01

High biomass producing plant species, such as Helianthus annuus, have potential for removing large amounts of trace metals by harvesting the aboveground biomass if sufficient metal concentrations in their biomass can be achieved However, the low bioavailability of heavy metals in soils and the limited translocation of heavy metals to the shoots by most high biomass producing plant species limit the efficiency of the phytoextraction process. Amendment of a contaminated soil with ethylene diamine tetraacetic acid (EDTA) or citric acid increases soluble heavy metal concentrations, potentially rendering them more available for plant uptake. This article discusses the effects of EDTA and citric acid on the uptake of heavy metals and translocation to aboveground harvestable plant parts in Helianthus annuus. EDTA was included in the research for comparison purposes in our quest for less persistent alternatives, suitable for enhanced phytoextraction. Plants were grown in a calcareous soil moderately contaminated with Cu, Pb, Zn, and Cd and treated with increasing concentrations of EDTA (0.1, 1, 3, 5, 7, and 10 mmol kg(-1) soil) or citric acid (0.01, 0.05, 0.25, 0.442, and 0.5 mol kg(-1) soil). Heavy metal concentrations in harvested shoots increased with EDTA concentration but the actual amount of phytoextracted heavy metals decreased at high EDTA concentrations, due to severe growth depression. Helianthus annuus suffered heavy metal stress due to the significantly increased bioavailable metal fraction in the soil. The rapid mineralization of citric acid and the high buffering capacity of the soil made citric acid inefficient in increasing the phytoextracted amounts of heavy metals. Treatments that did not exceed the buffering capacity of the soil (< 0.442 mol kg(-1) soil) did not result in any significant increase in shoot heavy metal concentrations. Treatments with high concentrations resulted in a dissolution of the carbonates and compaction of the soil. These physicochemical changes caused growth depression of Helianthus annuus. EDTA and citric acid added before sowing of Helianthus annuus did not appear to be efficient amendments when phytoextraction of heavy metals from calcareous soils is considered.

Measurements on NASA Langley Durable Combustor Rig by TDLAT: Preliminary Results

NASA Technical Reports Server (NTRS)

Busa, Kristin; Ellison, Erik N.; McGovern, Brian J.; McDaniel, James C.; Diskin, Glenn S.; DePiro, Maxwell J.; Capriotti, Diego P.; Gaffney, Richard L.

2013-01-01

Detailed knowledge of the internal structure of high-enthalpy flows can provide valuable insight to the performance of scramjet combustors. Tunable Diode Laser Absorption Spectroscopy (TDLAS) is often employed to measure temperature and species concentration. However, TDLAS is a path-integrated line-of-sight (LOS) measurement, and thus does not produce spatially resolved distributions. Tunable Diode Laser Absorption Tomography (TDLAT) is a non-intrusive measurement technique for determining two-dimensional spatially resolved distributions of temperature and species concentration in high enthalpy flows. TDLAT combines TDLAS with tomographic image reconstruction. Several separate line-of-sight TDLAS measurements are analyzed in order to produce highly resolved temperature and species concentration distributions. Measurements have been collected at the University of Virginia's Supersonic Combustion Facility (UVaSCF) as well as at the NASA Langley Direct-Connect Supersonic Combustion Test Facility (DCSCTF). Measurements collected at the DCSCTF required significant modifications to system hardware and software designs due to its larger measurement area and shorter test duration. Initial LOS measurements from the NASA Langley DCSCTF operating at an equivalence ratio of 0.5 are presented. Results show the capability of TDLAT to adapt to several experimental setups and test parameters.

[Effect of a high fat or high carbohydrate breakfast on postprandial lipid profile in healthy subjects with or without family history of type 2 diabetes mellitus].

PubMed

González-Ortiz, Manuel; Balcázar-Muñoz, Blanca R; Mora-Martínez, José M; Martínez-Abundis, Esperanza

2004-09-01

The objective of this study was to evaluate the effect of a high fat or high carbohydrate breakfast on postprandial lipid profile in healthy subjects with or without family history of type 2 diabetes mellitus. A single blind, controlled clinical trial with parallel groups was performed in 20 healthy subjects; 10 subjects with family history of type 2 diabetes mellitus and 10 individuals without that background. Each group was randomized to receive a high fat or high carbohidrate breakfast. A metabolic profile that included fasting and postprandial lipids, as well as, the assessment of insulin sensitivity were performed. Lower high-lipoprotein cholesterol (p < 0.02) and apolipoprotein A1 (p < 0.03) concentrations were found in subjects with family history of type 2 diabetes mellitus than those without that background. In this same above mentioned group with the high carbohydrate breakfast, there were significant increments in apoliprotein B at minute 300 (p < 0.03) and in triglycerides at minute 360 (p < 0.03). In the group without family history of diabetes that received the high fat breakfast, there were increments in triglycerides (p < 0.03) and very-low density lipoprotein concentrations at minute 180 (p < 0.03). In conclusion, healthy subjects with family history of type 2 diabetes showed some atherogenic characteristics in their metabolic profile, and the high carbohydrate breakfast produced in them increments in apolipoprotein B and in triglycerides, meanwhile that, in those subjects without such background the high fast breakfast produced unfavorable effects on their lipid concentrations.

Effect of discharge on the chlorophyll a distribution in the tidally-influenced Potomac River

USGS Publications Warehouse

Bennett, J.P.; Woodward, J.W.; Shultz, D.J.

1986-01-01

In the tidal Potomac River, high river discharges during the spring are associated with high chlorophyll a concentrations in the following in the following summer, assuming that summertime light and temperature conditions are favorable. Spring floods deliver large loads of particulate N and P to the tidal river. This particulate N and P could be mineralized by bacteria to inorganic N and P and released to the water column where it is available for phytoplankton use during summertime. However, during the study period relatively low concentrations of chlorophyll a (less than 50 ??g l-1 occurred in the tidal river if average monthly discharge during July or August exceeded 200 m3s-1. Discharge and other conditions combined to produce conditions favorable for nuisance levels of chlorophyll a (greater than 100 ??g l-1 approximately one year out of four. Chlorophyll a maxima occurred in the Potomac River transition zone and estuary during late winter (dinoflagellates) and spring (diatoms). Typical seasonal peak concentrations were achieved at discharges as high as 970 m3 s-1, but sustained discharges greater than 1,100 m3 s-1 retarded development. Optimum growth conditions occurred following runoff events of 10 to 15 d duration which produced transit times to the transition zone of 7 to 10 d. Wet years with numerous moderate-sized runoff events, such as 1980, tend to produce greater biomass in the transition zone and estuary than do dry years such as 1981. ?? 1986 Estuarine Research Federation.

Efficacy of BRL 25000 against Serratia marcescens, Enterobacter cloacae, and Citrobacter freundii in urinary tract infections.

PubMed Central

Nakazawa, H; Hashimoto, T; Nishiura, T; Mitsuhashi, S

1983-01-01

Synergism between amoxicillin and clavulanic acid was not expected against cephalosporinase-producing bacterial strains because clavulanic acid has little inhibitory action on cephalosporinases. However, in a clinical trial of BRL 25000 (amoxicillin-clavulanic acid), excellent results were obtained in complicated urinary tract infections caused by Serratia marcescens, Enterobacter cloacae, and Citrobacter freundii strains which produced cephalosporinase and were highly resistant to amoxicillin alone. The good clinical efficacy of BRL 25000 in such urinary tract infections was probably due to the fact that the urinary concentration of clavulanic acid was higher than its minimal inhibitory concentrations for these strains. PMID:6357078

Increased expression of the yeast multidrug resistance ABC transporter Pdr18 leads to increased ethanol tolerance and ethanol production in high gravity alcoholic fermentation

PubMed Central

2012-01-01

Background The understanding of the molecular basis of yeast tolerance to ethanol may guide the design of rational strategies to increase process performance in industrial alcoholic fermentations. A set of 21 genes encoding multidrug transporters from the ATP-Binding Cassette (ABC) Superfamily and Major Facilitator Superfamily (MFS) in S. cerevisiae were scrutinized for a role in ethanol stress resistance. Results A yeast multidrug resistance ABC transporter encoded by the PDR18 gene, proposed to play a role in the incorporation of ergosterol in the yeast plasma membrane, was found to confer resistance to growth inhibitory concentrations of ethanol. PDR18 expression was seen to contribute to decreased 3 H-ethanol intracellular concentrations and decreased plasma membrane permeabilization of yeast cells challenged with inhibitory ethanol concentrations. Given the increased tolerance to ethanol of cells expressing PDR18, the final concentration of ethanol produced during high gravity alcoholic fermentation by yeast cells devoid of PDR18 was lower than the final ethanol concentration produced by the corresponding parental strain. Moreover, an engineered yeast strain in which the PDR18 promoter was replaced in the genome by the stronger PDR5 promoter, leading to increased PDR18 mRNA levels during alcoholic fermentation, was able to attain a 6 % higher ethanol concentration and a 17 % higher ethanol production yield than the parental strain. The improved fermentative performance of yeast cells over-expressing PDR18 was found to correlate with their increased ethanol tolerance and ability to restrain plasma membrane permeabilization induced throughout high gravity fermentation. Conclusions PDR18 gene over-expression increases yeast ethanol tolerance and fermentation performance leading to the production of highly inhibitory concentrations of ethanol. PDR18 overexpression in industrial yeast strains appears to be a promising approach to improve alcoholic fermentation performance for sustainable bio-ethanol production. PMID:22839110

Assessing Radium Activity in Shale Gas Produced Brine

NASA Astrophysics Data System (ADS)

Fan, W.; Hayes, K. F.; Ellis, B. R.

2015-12-01

The high volumes and salinity associated with shale gas produced water can make finding suitable storage or disposal options a challenge, especially when deep well brine disposal or recycling for additional well completions is not an option. In such cases, recovery of commodity salts from the high total dissolved solids (TDS) of the brine wastewater may be desirable, yet the elevated concentrations of the naturally occurring radionuclides such as Ra-226 and Ra-228 in produced waters (sometimes substantially greater than the EPA limit of 5 pCi/L) may concentrate during these steps and limit salt recovery options. Therefore, assessing the potential presence of these Ra radionuclides in produced water from shale gas reservoir properties is desirable. In this study, we seek to link U and Th content within a given shale reservoir to the expected Ra content of produced brine by accounting for secular equilibrium within the rock and subsequent release to Ra to native brines. Produced brine from a series of Antrim shale wells and flowback from a single Utica-Collingwood shale well in Michigan were sampled and analyzed via ICP-MS to measure Ra content. Gamma spectroscopy was used to verify the robustness of this new Ra analytical method. Ra concentrations were observed to be up to an order of magnitude higher in the Antrim flowback water samples compared to those collected from the Utica-Collingwood well. The higher Ra content in Antrim produced brines correlates well with higher U content in the Antrim (19 ppm) relative to the Utica-Collingwood (3.5 ppm). We also observed an increase in Ra activity with increasing TDS in the Antrim samples. This Ra-TDS relationship demonstrates the influence of competing divalent cations in controlling Ra mobility in these clay-rich reservoirs. In addition, we will present a survey of geochemical data from other shale gas plays in the U.S. correlating shale U, Th content with produced brine Ra content. A goal of this study is to develop a method to predict the expected Ra activity in shale gas produced brines on a regional or play-specific basis in an effort to guide wastewater management practices or optimize regional treatment strategies.

High Magnetic Susceptibility in a Highly Saline Sulfate-Rich Aquifer Undergoing Biodegradation of Hydrocarbon Results from Sulfate Reduction.

NASA Astrophysics Data System (ADS)

Atekwana, E. A.; Enright, A.; Ntarlagiannis, D.; Slater, L. D.; Bernier, R.; Beaver, C. L.; Rossbach, S.

2016-12-01

We investigated the chemical and stable carbon isotope composition of groundwater in a highly saline aquifer contaminated with hydrocarbon. Our aim to evaluate hydrocarbon degradation and to constrain the geochemical conditions that generated high anomalous magnetic susceptibility (MS) signatures observed at the water table interface. The occurrence of high MS in the water table fluctuating zone has been attributed to microbial iron reduction, suggesting the use of MS as a proxy for iron cycling. The highly saline aquifer had total dissolved solids concentrations of 3.7 to 29.3 g/L and sulfate concentrations of 787 to 37,100 mg/L. We compared our results for groundwater locations with high hydrocarbon contamination (total petroleum hydrocarbon (TPH) >10 mg/L), at lightly contaminated (TPH <10 mg/L) and locations with no contaminations. Our results for the terminal electron acceptors (TEAs) dissolved oxygen (DO), nitrate (NO3-), dissolved iron (Fe2+) , dissolved manganese (Mn2+), sulfate (SO42-) and methane (CH4) suggest a chemically heterogeneous aquifer, probably controlled by heterogeneous distribution of TEAs and contamination (type of hydrocarbon, phase and age of contamination). The concentrations of dissolved inorganic carbon (DIC) ranged from 67 to 648 mg C/L and the stable carbon isotope (δ13CDIC) ranged from -30.0‰ to 1.0 ‰ and DIC-δ13CDIC modeling indicates that the carbon in the DIC is derived primarily from hydrocarbon degradation. The concentrations of Fe2+ in the aquifer ranged from 0.1 to 55.8 mg/L, but was mostly low, averaging 2.7+10.9 mg/L. Given the low Fe2+ [AE1] in the aqueous phase and the high MS at contaminated locations, we suggest that the high MS observed does not arise from iron reduction but rather from sulfate reduction. Sulfate reduction produces H2S which reacts with Fe2+ to produce ferrous sulfide (Fe2+S) or the mixed valence greigite (Fe2+Fe3+2S4). We conclude that in highly saline aquifers with high concentrations of sulfate and contaminated with hydrocarbon, dominance of sulfate reduction as the TEA is responsible for iron cycling and therefore the high MS associated with biodegradation. [AE1]What about sulfate concentrations? And the range in salinity? You need to add these values to the bastrcat

Optical design considerations for high-concentration photovoltaics

NASA Astrophysics Data System (ADS)

Garboushian, Vahan; Gordon, Robert

2006-08-01

Over the past 15 years, major advances in Concentrating Photovoltaics (CPV) have been achieved. Ultra-efficient Si solar cells have produced commercial concentration systems which are being fielded today and are competitively priced. Advanced research has primarily focused on significantly more efficient multi-junction solar cells for tomorrow's systems. This effort has produced sophisticated solar cells that significantly improve power production. Additional performance and cost improvements, especially in the optical system area and system integration, must be made before CPV can realize its ultimate commercial potential. Structural integrity and reliability are vital for commercial success. As incremental technical improvements are made in solar cell technologies, evaluation and 'fine-tuning' of optical systems properly matched to the solar cell are becoming increasingly necessary. As we move forward, it is increasingly important to optimize all of the interrelated elements of a CPV system for high performance without sacrificing the marketable cost and structural requirements of the system. Areas such as wavelength absorption of refractive optics need to be carefully matched to the solar cell technology employed. Reflective optics require advanced engineering models to insure uniform flux distribution without excessive losses. In Situ measurement of the 'fine-grain' improvements are difficult as multiple variables such as solar insolation, temperature, wind, altitude, etc. infringe on analytical data. This paper discusses design considerations based on 10 years of field trials of high concentration systems and their relevance for tomorrow's advanced CPV systems.

Technology development of fabrication techniques for advanced solar dynamic concentrators

NASA Technical Reports Server (NTRS)

Richter, Scott W.

1991-01-01

The objective of the advanced concentrator program is to develop the technology that will lead to lightweight, highly reflective, accurate, scaleable, and long lived space solar dynamic concentrators. The advanced concentrator program encompasses new and innovative concepts, fabrication techniques, materials selection, and simulated space environmental testing. Fabrication techniques include methods of fabricating the substrates and coating substrate surfaces to produce high quality optical surfaces, acceptable for further coating with vapor deposited optical films. The selected materials to obtain a high quality optical surface include microsheet glass and Eccocoat EP-3 epoxy, with DC-93-500 selected as a candidate silicone adhesive and levelizing layer. The following procedures are defined: cutting, cleaning, forming, and bonding microsheet glass. Procedures are also defined for surface cleaning, and EP-3 epoxy application. The results and analyses from atomic oxygen and thermal cycling tests are used to determine the effects of orbital conditions in a space environment.

Potential sources of variability in mesocosm experiments on the response of phytoplankton to ocean acidification

NASA Astrophysics Data System (ADS)

Moreno de Castro, Maria; Schartau, Markus; Wirtz, Kai

2017-04-01

Mesocosm experiments on phytoplankton dynamics under high CO2 concentrations mimic the response of marine primary producers to future ocean acidification. However, potential acidification effects can be hindered by the high standard deviation typically found in the replicates of the same CO2 treatment level. In experiments with multiple unresolved factors and a sub-optimal number of replicates, post-processing statistical inference tools might fail to detect an effect that is present. We propose that in such cases, data-based model analyses might be suitable tools to unearth potential responses to the treatment and identify the uncertainties that could produce the observed variability. As test cases, we used data from two independent mesocosm experiments. Both experiments showed high standard deviations and, according to statistical inference tools, biomass appeared insensitive to changing CO2 conditions. Conversely, our simulations showed earlier and more intense phytoplankton blooms in modeled replicates at high CO2 concentrations and suggested that uncertainties in average cell size, phytoplankton biomass losses, and initial nutrient concentration potentially outweigh acidification effects by triggering strong variability during the bloom phase. We also estimated the thresholds below which uncertainties do not escalate to high variability. This information might help in designing future mesocosm experiments and interpreting controversial results on the effect of acidification or other pressures on ecosystem functions.

Biological Control Products for Aflatoxin Prevention in Italy: Commercial Field Evaluation of Atoxigenic Aspergillus flavus Active Ingredients.

PubMed

Mauro, Antonio; Garcia-Cela, Esther; Pietri, Amedeo; Cotty, Peter J; Battilani, Paola

2018-01-05

Since 2003, non-compliant aflatoxin concentrations have been detected in maize produced in Italy. The most successful worldwide experiments in aflatoxin prevention resulted from distribution of atoxigenic strains of Aspergillus flavus to displace aflatoxin-producers during crop development. The displacement results in lower aflatoxin concentrations in harvested grain. The current study evaluated in field performances of two atoxigenic strains of A . flavus endemic to Italy in artificially inoculated maize ears and in naturally contaminated maize. Co-inoculation of atoxigenic strains with aflatoxin producers resulted in highly significant reductions in aflatoxin concentrations (>90%) in both years only with atoxigenic strain A2085. The average percent reduction in aflatoxin B₁ concentration in naturally contaminated maize fields was 92.3%, without significant differences in fumonisins between treated and control maize. The vegetative compatibility group of A2085 was the most frequently recovered A. flavus in both treated and control plots (average 61.9% and 53.5% of the A. flavus , respectively). A2085 was therefore selected as an active ingredient for biocontrol products and deposited under provisions of the Budapest Treaty in the Belgian Co-Ordinated Collections of Micro-Organisms (BCCM/MUCL) collection (accession MUCL54911). Further work on development of A2085 as a tool for preventing aflatoxin contamination in maize produced in Italy is ongoing with the commercial product named AF-X1™.

Changes in salivary testosterone concentrations and subsequent voluntary squat performance following the presentation of short video clips.

PubMed

Cook, Christian J; Crewther, Blair T

2012-01-01

Previous studies have shown that visual images can produce rapid changes in testosterone concentrations. We explored the acute effects of video clips on salivary testosterone and cortisol concentrations and subsequent voluntary squat performance in highly trained male athletes (n=12). Saliva samples were collected on 6 occasions immediately before and 15 min after watching a brief video clip (approximately 4 min in duration) on a computer screen. The watching of a sad, erotic, aggressive, training motivational, humorous or a neutral control clip was randomised. Subjects then performed a squat workout aimed at producing a 3 repetition maximum (3RM) lift. Significant (P<0.001) relative (%) increases in testosterone concentrations were noted with watching the erotic, humorous, aggressive and training videos (versus control and sad), with testosterone decreasing significantly (versus control) after the sad clip. The aggressive video also produced an elevated cortisol response (% change) and more so than the control and humorous videos (P<0.001). A significant (P<0.003) improvement in 3RM performance was noted after the erotic, aggressive and training clips (versus control). A strong within-individual correlation (mean r=0.85) was also noted between the relative changes in testosterone and the 3RM squats across all video sessions (P<0.001). In conclusion, different video clips were associated with different changes in salivary free hormone concentrations and the relative changes in testosterone closely mapped 3RM squat performance in a group of highly trained males. Thus, speculatively, using short video presentations in the pre-workout environment offers an opportunity for understanding the outcomes of hormonal change, athlete behaviour and subsequent voluntary performance. Copyright © 2011 Elsevier Inc. All rights reserved.

Simultaneous biosorption of selenium, arsenic and molybdenum with modified algal-based biochars.

PubMed

Johansson, Charlotte L; Paul, Nicholas A; de Nys, Rocky; Roberts, David A

2016-01-01

Ash disposal waters from coal-fired power stations present a challenging water treatment scenario as they contain high concentrations of the oxyanions Se, As and Mo which are difficult to remove through conventional techniques. In an innovative process, macroalgae can be treated with Fe and processed through slow pyrolysis into Fe-biochar which has a high affinity for oxyanions. However, the effect of production conditions on the efficacy of Fe-biochar is poorly understood. We produced Fe-biochar from two algal sources; "Gracilaria waste" (organic remnants after agar is extracted from cultivated Gracilaria) and the freshwater macroalgae Oedogonium. Pyrolysis experiments tested the effects of the concentration of Fe(3+) in pre-treatment, and pyrolysis temperatures, on the efficacy of the Fe-biochar. The efficacy of Fe-biochar increased with increasing concentrations of Fe(3+) in the pre-treatment solutions, and decreased with increasing pyrolysis temperatures. The optimized Fe-biochar for each biomass was produced by treatment with a 12.5% w/v Fe(3+) solution, followed by slow pyrolysis at 300 °C. The Fe-biochar produced in this way had higher a biosorption capacity for As and Mo (62.5-80.7 and 67.4-78.5 mg g(-1) respectively) than Se (14.9-38.8 mg g(-1)) in single-element mock effluents, and the Fe-biochar produced from Oedogonium had a higher capacity for all elements than the Fe-biochar produced from Gracilaria waste. Regardless, the optimal Fe-biochars from both biomass sources were able to effectively treat Se, As and Mo simultaneously in an ash disposal effluent from a power station. The production of Fe-biochar from macroalgae is a promising technique for treatment of complex effluents containing oxyanions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Novel pre-treatment of zeolite materials for the removal of sodium ions: potential materials for coal seam gas co-produced wastewater.

PubMed

Santiago, Oscar; Walsh, Kerry; Kele, Ben; Gardner, Edward; Chapman, James

2016-01-01

Coal seam gas (CSG) is the extraction of methane gas that is desorbed from the coal seam and brought to the surface using a dewatering and depressurisation process within the saturated coalbed. The extracted water is often referred to as co-produced CSG water. In this study, co-produced water from the coal seam of the Bowen Basin (QLD, Australia) was characterised by high concentration levels of Na(+) (1156 mg/L), low concentrations of Ca(2+) (28.3 mg/L) and Mg(2+) (5.6 mg/L), high levels of salinity, which are expected to cause various environmental problems if released to land or waters. The potential treatment of co-produced water using locally sourced natural ion exchange (zeolite) material was assessed. The zeolite material was characterized for elemental composition and crystal structure. Natural, untreated zeolite demonstrated a capacity to adsorb Na(+) ions of 16.16 mEq/100 g, while a treated zeolite using NH4 (+) using a 1.0 M ammonium acetate (NH4C2H3O2) solution demonstrated an improved 136 % Na(+) capacity value of 38.28 mEq/100 g after 720 min of adsorption time. The theoretical exchange capacity of the natural zeolite was found to be 154 mEq/100 g. Reaction kinetics and diffusion models were used to determine the kinetic and diffusion parameters. Treated zeolite using a NH4 (+) pre-treatment represents an effective treatment to reduce Na(+) concentration in coal seam gas co-produced waters, supported by the measured and modelled kinetic rates and capacity.

Oxygen produced by cyanobacteria in simulated Archaean conditions partly oxidizes ferrous iron but mostly escapes-conclusions about early evolution.

PubMed

Rantamäki, Susanne; Meriluoto, Jussi; Spoof, Lisa; Puputti, Eeva-Maija; Tyystjärvi, Taina; Tyystjärvi, Esa

2016-12-01

The Earth has had a permanently oxic atmosphere only since the great oxygenation event (GOE) 2.3-2.4 billion years ago but recent geochemical research has revealed short periods of oxygen in the atmosphere up to a billion years earlier before the permanent oxygenation. If these "whiffs" of oxygen truly occurred, then oxygen-evolving (proto)cyanobacteria must have existed throughout the Archaean aeon. Trapping of oxygen by ferrous iron and other reduced substances present in Archaean oceans has often been suggested to explain why the oxygen content of the atmosphere remained negligible before the GOE although cyanobacteria produced oxygen. We tested this hypothesis by growing cyanobacteria in anaerobic high-CO 2 atmosphere in a medium with a high concentration of ferrous iron. Microcystins are known to chelate iron, which prompted us also to test the effects of microcystins and nodularins on iron tolerance. The results show that all tested cyanobacteria, especially nitrogen-fixing species grown in the absence of nitrate, and irrespective of the ability to produce cyanotoxins, were iron sensitive in aerobic conditions but tolerated high concentrations of iron in anaerobicity. This result suggests that current cyanobacteria would have tolerated the high-iron content of Archaean oceans. However, only 1 % of the oxygen produced by the cyanobacterial culture was trapped by iron, suggesting that large-scale cyanobacterial photosynthesis would have oxygenated the atmosphere even if cyanobacteria grew in a reducing ocean. Recent genomic analysis suggesting that ability to colonize seawater is a secondary trait in cyanobacteria may offer a partial explanation for the sustained inefficiency of cyanobacterial photosynthesis during the Archaean aeon, as fresh water has always covered a very small fraction of the Earth's surface. If oxygenic photosynthesis originated in fresh water, then the GOE marks the adaptation of cyanobacteria to seawater, and the late-Proterozoic increase in oxygen concentration of the atmosphere is caused by full oxidation of the oceans.

Novel bioevaporation process for the zero-discharge treatment of highly concentrated organic wastewater.

PubMed

Yang, Benqin; Zhang, Lei; Lee, Yongwoo; Jahng, Deokjin

2013-10-01

A novel process termed as bioevaporation was established to completely evaporate wastewater by metabolic heat released from the aerobic microbial degradation of the organic matters contained in the highly concentrated organic wastewater itself. By adding the glucose solution and ground food waste (FW) into the biodried sludge bed, the activity of the microorganisms in the biodried sludge was stimulated and the water in the glucose solution and FW was evaporated. As the biodegradable volatile solids (BVS) concentration in wastewater increased, more heat was produced and the water removal ratio increased. When the volatile solids (VS) concentrations of both glucose and ground FW were 120 g L(-1), 101.7% and 104.3% of the added water was removed, respectively, by completely consuming the glucose and FW BVS. Therefore, the complete removal of water and biodegradable organic contents was achieved simultaneously in the bioevaporation process, which accomplished zero-discharge treatment of highly concentrated organic wastewater. Copyright © 2013 Elsevier Ltd. All rights reserved.

Design of a new concentrated photovoltaic system under UAE conditions

NASA Astrophysics Data System (ADS)

Hachicha, Ahmed Amine; Tawalbeh, Muahammad

2017-06-01

Concentrated Photovoltaic Systems (CPVs) are considered one of the innovative designs for concentrated solar power applications. By concentrating the incident radiation, the solar cells will be able to produce much more electricity compared to conventional PV systems. However, the temperature of the solar cells increases significantly with concentration. Therefore, cooling of the solar cells will be needed to maintain high conversion efficiency. In this work, a novel design of CPV system is proposed and implemented under UAE conditions for electricity generation and hot water production. The proposed design integrates a water cooling system and PV system to optimize both the electrical and thermal performances of the CPV system.

Treatment of biomass to obtain a target chemical

DOEpatents

Dunson, Jr., James B.; Tucker, III, Melvin P.; Elander, Richard T.; Hennessey, Susan Marie

2010-08-24

Target chemicals were produced using biocatalysts that are able to ferment sugars derived from treated biomass. Sugars were obtained by pretreating biomass under conditions of high solids and low ammonia concentration, followed by saccharification.

Ultra-High Efficiency, High-Concentration PV System Based On Spectral Division Between GaInP/GaInAs/Ge And BPC Silicon Cells

NASA Astrophysics Data System (ADS)

Benítez, P.; Mohedano, R.; Buljan, M.; Miñano, J. C.; Sun, Y.; Falicoff, W.; Vilaplana, J.; Chaves, J.; Biot, G.; López, J.

2011-12-01

A novel HCPV nonimaging concentrator concept with high concentration (>500×) is presented. It uses the combination of a commercial concentration GaInP/GaInAs/Ge 3J cell and a concentration Back-Point-Contact (BPC) concentration silicon cell for efficient spectral utilization, and external confinement techniques for recovering the 3J cell's reflection. The primary optical element (POE) is a flat Fresnel lens and the secondary optical element (SOE) is a free-form RXI-type concentrator with a band-pass filter embedded it, both POE and SOE performing Köhler integration to produce light homogenization. The band-pass filter sends the IR photons in the 900-1200 nm band to the silicon cell. Computer simulations predict that four-terminal terminal designs could achieve ˜46% added cell efficiencies using commercial 39% 3J and 26% Si cells. A first proof-of concept receiver prototype has been manufactured using a simpler optical architecture (with a lower concentration, ˜100× and lower simulated added efficiency), and experimental measurements have shown up to 39.8% 4J receiver efficiency using a 3J with peak efficiency of 36.9%.

Effect of dietary fiber on microbial activity and microbial gas production in various regions of the gastrointestinal tract of pigs.

PubMed Central

Jensen, B B; Jørgensen, H

1994-01-01

The microbial activity, composition of the gas phase, and gas production rates in the gastrointestinal tract of pigs fed either a low- or a high-fiber diet were investigated. Dense populations of culturable anaerobic bacteria, high ATP concentrations, and high adenylate energy charges were found for the last third of the small intestine, indicating that substantial microbial activity takes place in that portion of the gut. The highest microbial activity (highest bacterium counts, highest ATP concentration, high adenylate energy charge, and low pH) was found in the cecum and proximal colon. Greater microbial activity was found in the stomach and all segments of the hindgut in the pigs fed the high-fiber diet than in the pigs fed the low-fiber diet. Considerable amounts of O2 were found in the stomach (around 5%), while the content of O2 in gas samples taken from all other parts of the gastrointestinal tract was < 1%. The highest concentrations and highest production rates for H2 were found in the last third of the small intestine. No methane could be detected in the stomach or the small intestine. The rate of production and concentration of methane in the cecum and the proximal colon were low, followed by a steady increase in the successive segments of the hindgut. A very good correlation between in vivo and in vitro measurements of methane production was found. The amount of CH4 produced by pigs fed the low-fiber diet was 1.4 liters/day per animal. Substantially larger amounts of CH4 were produced by pigs fed the high-fiber diet (12.5 liters/day)(ABSTRACT TRUNCATED AT 250 WORDS) PMID:8031085

MCS precipitation and downburst intensity response to increased aerosol concentrations

NASA Astrophysics Data System (ADS)

Clavner, M.; Cotton, W. R.; van den Heever, S. C.

2015-12-01

Mesoscale convective systems (MCSs) are important contributors to rainfall in the High Plains of the United States as well as producers of severe weather such as hail, tornados and straight-line wind events known as derechos. Past studies have shown that changes in aerosol concentrations serving as cloud condensation nuclei (CCN) alter the MCS hydrometeor characteristics which in turn modify precipitation yield, downdraft velocity, cold-pool strength, storm propagation and the potential for severe weather to occur. In this study, the sensitivity of MCS precipitation characteristics and convective downburst velocities associated with a derecho to changes in CCN concentrations were examined by simulating a case study using the Regional Atmospheric Modeling System (RAMS). The case study of the 8 May 2009 "Super-Derecho" MCS was chosen since it produced a swath of widespread wind damage in association with an embedded large-scale bow echo, over a broad region from the High Plains of western Kansas to the foothills of the Appalachians. The sensitivity of the storm to changes in CCN concentrations was examined by conducting a set of three simulations which differed in the initial aerosol concentration based on output from the 3D chemical transport model, GEOS-Chem. Results from this study indicate that while increasing CCN concentrations led to an increase in precipitation rates, the changes to the derecho strength were not linear. A moderate increase in aerosol concentration reduced the derecho strength, while the simulation with the highest aerosol concentrations increased the derecho intensity. These changes are attributed to the impact of enhanced CCN concentration on the production of convective downbursts. An analysis of aerosol loading impacts on these MCS features will be presented.

Occurrence of nitrous oxide in the central High Plains aquifer, 1999

USGS Publications Warehouse

McMahon, P.B.; Bruch, B.W.; Becker, M.F.; Pope, L.M.; Dennehy, K.F.

2000-01-01

Nitrogen-enriched groundwater has been proposed as an important anthropogenic source of atmospheric nitrous oxide (N2O), yet few measurements of N2O in large aquifer systems have been made. Concentrations of N2O in water samples collected from the 124 000 km2 central High Plains aquifer in 1999 ranged from < 1 to 940 nM, with a median concentration of 29 nM (n = 123). Eighty percent of the N20 concentrations exceeded the aqueous concentration expected from equilibration with atmospheric N2O. Measurements of N2O, NO3-, and 3H in unsaturated-zone sediments, recently recharged groundwater, and older groundwater indicate that concentrations of N2O in groundwater increased over time and will likely continue to increase in the future as N-enriched water recharges the aquifer. Large concentrations of O2 and NO3- and small concentrations of NH4+ and dissolved organic carbon in the aquifer indicate that N2O in the central High Plains aquifer was produced primarily by nitrification. Calculations indicate that the flux of N2O from the central High Plains aquifer to the atmosphere from well pumping and groundwater discharge to streams was not a significant source of atmospheric N2O.Nitrogen-enriched groundwater has been proposed as an important anthropogenic source of atmospheric nitrous oxide (N2O), yet few measurements of N2O in large aquifer systems have been made. Concentrations of N2O in water samples collected from the 124000 km2 central High Plains aquifer in 1999 ranged from < 1 to 940 nM, with a median concentration of 29 nM (n = 123). Eighty percent of the N2O concentrations exceeded the aqueous concentration expected from equilibration with atmospheric N2O. Measurements of N2O, NO3-, and 3H in unsaturated-zone sediments, recently recharged groundwater, and older groundwater indicate that concentrations of N2O in groundwater increased over time and will likely continue to increase in the future as N-enriched water recharges the aquifer. Large concentrations of O2 and NO3- and small concentrations of NH4+ and dissolved organic carbon in the aquifer indicate that N2O in the central High Plains aquifer was produced primarily by nitrification. Calculations indicate that the flux of N2O from the central High Plains aquifer to the atmosphere from well pumping and groundwater discharge to streams was not a significant source of atmospheric N2O.Water samples were collected from 92 domestic wells, 16 monitoring wells and 15 public-supply wells in the High Plains Aquifer in 1999, and concentrations of nitrous oxide were measured. The groundwater concentrations ranged from less than 1 to 940 nM. Concentrations expressed as a percent of saturation in water ranged from less than 10 to 9690%. A significant decrease was noted in N2O concentrations with increasing depth of the well screen below the water table, and a significant positive correlation was found between the concentrations of N2O and nitrate. The small area-averaged N2O emission rate for the aquifer indicated that it was not an important component of the atmospheric N2O budget, but the importance could increase as groundwater N2O concentrations increase.

Using Ozone Lidar to Investigate Sources of High Ozone Concentrations in the Western United States

NASA Astrophysics Data System (ADS)

Senff, C. J.; Langford, A. O.; Alvarez, R. J.; Brewer, Wm. A.; Banta, R. M.; Marchbanks, R. D.; Sandberg, S. P.; Weickmann, A. M.; Holloway, J. S.; Williams, E. J.

2016-06-01

We have used NOAA's Tunable Optical Profiler for Aerosol and oZone (TOPAZ) ozone lidar to investigate the sources of high surface ozone concentrations in two different regions of the western United States (US): the Uintah Basin in northeast Utah and Clark County in southern Nevada, which includes the city of Las Vegas. The Uintah Basin is a booming oil and gas producing region that often suffers from very high wintertime ozone concentrations. Clark County experiences violations of the US ozone standard primarily in spring and early summer despite a lack of any major local pollution sources. TOPAZ lidar observations, in conjunction with surface in situ measurements and model results, provided strong evidence that the high wintertime ozone concentrations in the Uintah Basin are primarily driven by local emissions associated with oil and gas exploration, whereas the Clark County ozone exceedances are often caused by ozone-rich air that is transported from the lower stratosphere all the way down to the earth's surface.

METHOD FOR PREPARING NORMORPHINE

DOEpatents

Rapoport, H.; Look, M.

1959-06-01

An improved method is presented for producing normorphine from morphine. Morphine as the starting material is acetylated by treatment with acetylating agents to produce di-acetyl morphine (heroin). The acetylated compound is reacted with cyanating agents to produce di-acetyl-cyanonormorphine (cyanonorheroin). The di-acetyl-cyanonormorphine compound is then treated in accordance with the improved hydrolysis reactions of the present invention in which concentrated hydrochloric acid is employed for a limited time period to hydrolyze the acetyl group therefrom forming cyanonormorphine. Subsequently, the reaction mixture is diluted and hydrolysis of the cyano groups from the cyanonormorphine is effected with a longer contact time with dilute hydrochloric acid thereby producing normorphine. A high over-all conversion and production of a high purity product which may be radioactlvely labeled, if desired, is obtained by operation of the process.

Distribution of lead and cadmium in trophic levels of some marine organisms.

PubMed

Mesmar, M

1987-01-01

The concentrations of lead and cadmium in two species of algae, two species of invertebrates, and one species of fish (from Fehmern Baltic Sea) were determined using atomic absorption spectrophotometry. The concentrations of these metals at the producer level (algae) were always higher than at the consumer level. Also, among the consumers there was an obvious difference according to feeding habits, in such a way that they could be ranked according to their high content of lead and cadmium as follows: filter feeder (detritous feeder), plankton feeder. In addition, distribution of lead and cadmium varied within the individual producer (Fucus vesiculosus) in such a way that the holdfast exhibited the highest concentration followed by the apcial tip and the branches of the first dichotomy was the lowest. This alga reflects clear selectivity in absorbing more lead than cadmium.

Overcoming sodium toxicity by utilizing grass leaves as co-substrate during the start-up of batch thermophilic anaerobic digestion.

PubMed

Suwannoppadol, Suwat; Ho, Goen; Cord-Ruwisch, Ralf

2012-12-01

Sodium toxicity is a common problem causing inhibition of anaerobic digestion, and digesters treating highly concentrated wastes, such as food and municipal solid waste, and concentrated animal manure, are likely to suffer from partial or complete inhibition of methane-producing consortia, including methanogens. When grass clippings were added at the onset of anaerobic digestion of acetate containing a sodium concentration of 7.8 gNa(+)/L, a total methane production about 8L/L was obtained, whereas no methane was produced in the absence of grass leaves. In an attempt to narrow down which components of grass leaves caused decrease of sodium toxicity, different hypotheses were tested. Results revealed that betaine could be a significant compound in grass leaves causing reduction to sodium inhibition. Copyright © 2012 Elsevier Ltd. All rights reserved.

Solar thermal power systems point-focusing distributed receiver technology project. Volume 2: Detailed report

NASA Technical Reports Server (NTRS)

1980-01-01

The accomplishments of the Point-Focusing Distributed Receiver Technology Project during fiscal year 1979 are detailed. Present studies involve designs of modular units that collect and concentrate solar energy via highly reflective, parabolic-shaped dishes. The concentrated energy is then converted to heat in a working fluid, such as hot gas. In modules designed to produce heat for industrial applications, a flexible line conveys the heated fluid from the module to a heat transfer network. In modules designed to produce electricity the fluid carries the heat directly to an engine in a power conversion unit located at the focus of the concentrator. The engine is mechanically linked to an electric generator. A Brayton-cycle engine is currently being developed as the most promising electrical energy converter to meet near-future needs.

[Glutathione participation in regulating the secretory function of the stomach].

PubMed

Shlygin, G K; Vasilevskaia, L S; Martinchik, A N; Ignatenko, L G

1987-01-01

In experiments on dogs with Pavlov's pouches it was shown that glutathione infusion into the blood produced a highly pronounced stimulating effect on the gastric secretion induced by pentagastrin. Endogenous glutathione produced similar effect. It was found that intake as a drink of mono-sodium glutamate led to a significant increase of glutathione concentration in the dogs' blood, that was, probably, the result of its intensified production in the intestinal wall and passing into the blood. The growth of glutathione concentration in the blood coincided with its stimulating effect on the gastric secretion. Glutathione administered separately into the blood, or intake of glutathione without pentagastrin did not produce stimulating effect on gastric secretion. The data presented have evidenced that glutathione, besides its known functions, plays a role of the factor engaged in the regulation of gastric secretion.

Schizosaccharomyces pombe and Saccharomyces cerevisiae yeasts in sequential fermentations: Effect on phenolic acids of fermented Kei-apple (Dovyalis caffra L.) juice.

PubMed

Minnaar, P P; Jolly, N P; Paulsen, V; Du Plessis, H W; Van Der Rijst, M

2017-09-18

Kei-apple (Dovyalis caffra) is an evergreen tree indigenous to Southern Africa. The fruit contains high concentrations of l-malic acid, ascorbic acid, and phenolic acids. Kei-apple juice was sequentially inoculated with Schizosaccharomyces pombe and Saccharomyces cerevisiae yeasts. A reference fermentation using only S. cerevisiae was included. The fermentation was monitored by recording mass loss. At the end of fermentation, twelve untrained judges conducted free choice aroma profiling on the fruit wines. The Kei-apple juice and wines were analysed for total titratable acidity, total soluble solids, pH, alcohol, l-malic acid, and phenolic acids. Total titratable acidity was ca. 70% lower in Kei-apple wines produced with S. pombe+S. cerevisiae than in Kei-apple juice. Kei-apple wines produced with S. pombe+S. cerevisiae showed substantially lower concentrations of l-malic acid than Kei-apple wines produced with S. cerevisiae only. Wines produced with S. cerevisiae only proved higher in phenolic acid concentrations than wines produced with S. pombe+S. cerevisiae. Chlorogenic acid was the most abundant phenolic acid measured in the Kei-apple wines, followed by protocatechuic acid. Judges described the Kei-apple wines produced with S. pombe+S. cerevisiae as having noticeable off-odours, while wines produced with S. cerevisiae were described as fresh and fruity. Kei-apple wines (S. pombe+S. cerevisiae and S. cerevisiae) were of comparable vegetative and organic character. Saccharomyces cerevisiae produced Kei-apple wine with increased caffeic, chlorogenic, protocatechuic, and sinapic acids, whereas S. pombe+S. cerevisiae produced Kei-apple wines with increased ferulic, and p-coumaric acids and low l-malic acid. Copyright © 2017 Elsevier B.V. All rights reserved.

Production and functional evaluation of a protein concentrate from giant squid (Dosidicus gigas) by acid dissolution and isoelectric precipitation.

PubMed

Cortés-Ruiz, Juan A; Pacheco-Aguilar, Ramón; Elena Lugo-Sánchez, M; Gisela Carvallo-Ruiz, M; García-Sánchez, Guillermina

2008-09-15

A protein concentrate from giant squid (Dosidicus gigas) was produced under acidic conditions and its functional-technological capability evaluated in terms of its gel-forming ability, water holding capacity and colour attributes. Technological functionality of the concentrate was compared with that of squid muscle and a neutral concentrate. Protein-protein aggregates insoluble at high ionic strength (I=0.5M), were detected in the acidic concentrate as result of processing with no preclusion of its gel-forming ability during the sol-to-gel thermal transition. Even though washing under acidic condition promoted autolysis of the myosin heavy chain, the acidic concentrate displayed an outstanding ability to gel giving samples with a gel strength of 455 and 1160gcm at 75% and 90% compression respectively, and an AA folding test grade indicative of high gel strength, elasticity, and cohesiveness. The process proved to be a good alternative for obtaining a functional protein concentrate from giant squid muscle. Copyright © 2008. Published by Elsevier Ltd.

Spider Silk Fibers Spun from Soluble Recombinant Silk Produced in Mammalian Cells

NASA Astrophysics Data System (ADS)

Lazaris, Anthoula; Arcidiacono, Steven; Huang, Yue; Zhou, Jiang-Feng; Duguay, François; Chretien, Nathalie; Welsh, Elizabeth A.; Soares, Jason W.; Karatzas, Costas N.

2002-01-01

Spider silks are protein-based ``biopolymer'' filaments or threads secreted by specialized epithelial cells as concentrated soluble precursors of highly repetitive primary sequences. Spider dragline silk is a flexible, lightweight fiber of extraordinary strength and toughness comparable to that of synthetic high-performance fibers. We sought to ``biomimic'' the process of spider silk production by expressing in mammalian cells the dragline silk genes (ADF-3/MaSpII and MaSpI) of two spider species. We produced soluble recombinant (rc)-dragline silk proteins with molecular masses of 60 to 140 kilodaltons. We demonstrated the wet spinning of silk monofilaments spun from a concentrated aqueous solution of soluble rc-spider silk protein (ADF-3; 60 kilodaltons) under modest shear and coagulation conditions. The spun fibers were water insoluble with a fine diameter (10 to 40 micrometers) and exhibited toughness and modulus values comparable to those of native dragline silks but with lower tenacity. Dope solutions with rc-silk protein concentrations >20% and postspinning draw were necessary to achieve improved mechanical properties of the spun fibers. Fiber properties correlated with finer fiber diameter and increased birefringence.

Flow-induced gelation of microfiber suspensions.

PubMed

Perazzo, Antonio; Nunes, Janine K; Guido, Stefano; Stone, Howard A

2017-10-10

The flow behavior of fiber suspensions has been studied extensively, especially in the limit of dilute concentrations and rigid fibers; at the other extreme, however, where the suspensions are concentrated and the fibers are highly flexible, much less is understood about the flow properties. We use a microfluidic method to produce uniform concentrated suspensions of high aspect ratio, flexible microfibers, and we demonstrate the shear thickening and gelling behavior of such microfiber suspensions, which, to the best of our knowledge, has not been reported previously. By rheological means, we show that flowing the suspension triggers the irreversible formation of topological entanglements of the fibers resulting in an entangled water-filled network. This phenomenon suggests that flexible fiber suspensions can be exploited to produce a new family of flow-induced gelled materials, such as porous hydrogels. A significant consequence of these flow properties is that the microfiber suspension is injectable through a needle, from which it can be extruded directly as a hydrogel without any chemical reactions or further treatments. Additionally, we show that this fiber hydrogel is a soft, viscoelastic, yield-stress material.

Cyanobacteria and Cyanotoxins Occurrence and Removal from Five High-Risk Conventional Treatment Drinking Water Plants.

PubMed

Szlag, David C; Sinclair, James L; Southwell, Benjamin; Westrick, Judy A

2015-06-12

An environmental protection agency EPA expert workshop prioritized three cyanotoxins, microcystins, anatoxin-a, and cylindrospermopsin (MAC), as being important in freshwaters of the United States. This study evaluated the prevalence of potentially toxin producing cyanobacteria cell numbers relative to the presence and quantity of the MAC toxins in the context of this framework. Total and potential toxin producing cyanobacteria cell counts were conducted on weekly raw and finished water samples from utilities located in five US states. An Enzyme-Linked Immunosorbant Assay (ELISA) was used to screen the raw and finished water samples for microcystins. High-pressure liquid chromatography with a photodiode array detector (HPLC/PDA) verified microcystin concentrations and quantified anatoxin-a and cylindrospermopsin concentrations. Four of the five utilities experienced cyanobacterial blooms in their raw water. Raw water samples from three utilities showed detectable levels of microcystins and a fourth utility had detectable levels of both microcystin and cylindrospermopsin. No utilities had detectable concentrations of anatoxin-a. These conventional plants effectively removed the cyanobacterial cells and all finished water samples showed MAC levels below the detection limit by ELISA and HPLC/PDA.

Phenolic compounds, organic acids and antioxidant activity of grape juices produced from new Brazilian varieties planted in the Northeast Region of Brazil.

PubMed

Lima, Marcos Dos Santos; Silani, Igor de Souza Veras; Toaldo, Isabela Maia; Corrêa, Luiz Claudio; Biasoto, Aline Camarão Telles; Pereira, Giuliano Elias; Bordignon-Luiz, Marilde T; Ninow, Jorge Luiz

2014-10-15

The phenolic compounds, organic acids and the antioxidant activity were determined for grape juice samples from new Brazilian varieties grown in the Sub-middle São Francisco Valley in the Northeast Region of Brazil. The results showed that the Brazilian grape juices have high antioxidant activity, which was significantly correlated with the phenolic compounds catechin, epicatechin gallate, procyanidin B1, rutin, gallic acid, caffeic acid, p-coumaric acid, pelargonidin-3-glucoside, cyanidin-3-glucoside, cyaniding-3,5-diglucoside and delphinidin-3-glucoside. The produced juice samples showed higher concentrations of trans-resveratrol than those observed in juices made from different varieties of grapes from traditional growing regions. Organic acids concentrations were similar to those of juices produced from other classical varieties. It was demonstrated that it is possible to prepare juices from grapes of new varieties grown in the Northeast of Brazil containing a high content of bioactive compounds and typical characteristics of the tropical viticulture practised in the Sub-middle São Francisco Valley. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effects of the addition of different nitrogen sources in the tequila fermentation process at high sugar concentration.

PubMed

Arrizon, J; Gschaedler, A

2007-04-01

To study the effect of the addition of different nitrogen sources at high sugar concentration in the tequila fermentation process. Fermentations were performed at high sugar concentration (170 g l(-1)) using Agave tequilana Weber blue variety with and without added nitrogen from different sources (ammonium sulfate; glutamic acid; a mixture of ammonium sulfate and amino acids) during the exponential phase of growth. All the additions increased the fermentation rate and alcohol efficiency. The level of synthesis of volatile compounds depended on the source added. The concentration of amyl alcohols and isobutanol were decreased while propanol and acetaldehyde concentration increased. The most efficient nitrogen sources for fermentation rate were ammonium sulfate and the mixture of ammonium sulfate and amino acids. The level of volatile compounds produced depended upon types of nitrogen. The synthesis of some volatile compounds increased while others decreased with nitrogen addition. The addition of nitrogen could be a strategy for improving the fermentation rate and efficiency in the tequila fermentation process at high sugar Agave tequilana concentration. Furthermore, the sensory quality of the final product may change because the synthesis of the volatile compounds is modified.

The arsenic removal from arsenopyrite in sulfide mineral by physicochemical extraction

NASA Astrophysics Data System (ADS)

Jo, Jiyu; Cho, Kanghee; Choi, Nagchoul; Park*, Cheonyoung

2015-04-01

The most abundant As ore mineral is arsenopyrite (FeAsS). Arsenopyrite is present in sulfide ores associated with sediment-hosted Au deposits, it tends to be the earliest-formed mineral, derived from hydrothermal solutions and formed at temperatures typically of 100(degree Celsius) or more. The aim of this study was to investigate the mineralogical phase change and arsenic removal from arsenopyrite as a penalty element in sulfide mineral contained Au by physical extraction (high frequency) and chemical leaching (thiocyanate). Arsenic removal experiments for were performed under various conditions of high frequency exposure(1~35 min), thiocyanate concentration (0.1~1.0M), HCl concentration (0.1~2.0M), copper(2) sulfate concentration (0.1~1.0M), temperature (30~60 degree Celsius). Increasing the high frequency exposure produced a positive effect on arsenic removal in arsenopyrite. The highest percentage arsenic removal of 96.67% was obtained under the following conditions by thiocyanate leaching: thiocyanate concentration = 1.0M ; HCl concentration = 2.0M ; copper(2) sulfate concentration = 1.0M ; temperature = 60(degree Celsius) This study demonstrates the adequate performance of physical extraction (high frequency) and chemical leaching (thiocyanate) for the arsenic removal from arsenopyrite as a penalty element.

High-concentration sugars production from corn stover based on combined pretreatments and fed-batch process.

PubMed

Yang, Maohua; Li, Wangliang; Liu, Binbin; Li, Qiang; Xing, Jianmin

2010-07-01

In this paper, high-concentration sugars were produced from pretreated corn stover. The raw corn stover was pretreated in a process combining steam explosion and alkaline hydrogen-peroxide. The hemicellulose and lignin were removed greatly. The cellulose content increased to 73.2%. Fed-batch enzymatic hydrolysis was initiated with 12% (w/v) solids loading and 20 FPU/g solids. Then, 6% solids were fed consecutively at 12, 36 and 60 h. After 144 h, the final concentrations of reducing sugar, glucose, cellobiose and xylose reached 220, 175, 22 and 20 g/L, respectively. The final total biomass conversion was 60% in fed-batch process. Copyright 2009 Elsevier Ltd. All rights reserved.

Heavy metals in urban soils of East St. Louis, IL, Part I: Total concentration of heavy metals in soils.

PubMed

Kaminski, M D; Landsberger, S

2000-09-01

The city of East St. Louis, IL, has a history of abundant industrial activities including smelters of ferrous and non-ferrous metals, a coal-fired power plant, companies that produce organic and inorganic chemicals, and petroleum refineries. A protocol for soil analysis was developed to produce sufficient information on the extent of heavy metal contamination in East St. Louis soils. Soil cores representing every borough of East St. Louis were analyzed for heavy metals--As, Cd, Cu, Cr, Hg, Ni, Pb, Sb, Sn, and Zn. The topsoil contained heavy metal concentrations as high as 12.5 ppm Cd, 14,400 ppm Cu, ppm quantities of Hg, 1860 ppm Pb, 40 ppm Sb, 1130 ppm Sn, and 10,360 ppm Zn. Concentrations of Sb, Cu, and Cd were well correlated with Zn concentrations, suggesting a similar primary industrial source. In a sandy loam soil from a vacated rail depot near the bank of the Mississippi River, the metals were evenly distributed down to a 38-cm depth. The clay soils within a half-mile downwind of the Zn smelter and Cu products company contained elevated Cd (81 ppm), Cu (340 ppm), Pb (700 ppm), and Zn (6000 ppm) and displayed a systematic drop in concentration of these metals with depth. This study demonstrates the often high concentration of heavy metals heterogeneously distributed in the soil and provides baseline data for continuing studies of heavy metal soil leachability.

The effect of mineral dust and soot aerosols on ice microphysics near the foothills of the Himalayas: A numerical investigation

NASA Astrophysics Data System (ADS)

Hazra, Anupam; Padmakumari, B.; Maheskumar, R. S.; Chen, Jen-Ping

2016-05-01

This study investigates the influence of different ice nuclei (IN) species and their number concentrations on cloud ice production. The numerical simulation with different species of ice nuclei is investigated using an explicit bulk-water microphysical scheme in a Mesoscale Meteorological Model version 5 (MM5). The species dependent ice nucleation parameterization that is based on the classical nucleation theory has been implemented into the model. The IN species considered include dust and soot with two different concentrations (Low and High). The simulated cloud microphysical properties like droplet number concentration and droplet effective radii as well as macro-properties (equivalent potential temperature and relative humidity) are comparable with aircraft observations. When higher dust IN concentrations are considered, the simulation results showed good agreement with the cloud ice and cloud water mixing ratio from aircraft measurements during Cloud Aerosol Interactions and Precipitation Enhancement Experiment (CAIPEEX) and Modern Era Retrospective Analysis for Research and Applications (MERRA) reanalysis. Relative importance of IN species is shown as compared to the homogeneous freezing nucleation process. The tendency of cloud ice production rates is also analyzed and found that dust IN is more efficient in producing cloud ice when compared to soot IN. The dust IN with high concentration can produce more surface precipitation than soot IN at the same concentration. This study highlights the need to improve the ice nucleation parameterization in numerical models.

Icosapent ethyl: Eicosapentaenoic acid concentration and triglyceride-lowering effects across clinical studies.

PubMed

Bays, Harold E; Ballantyne, Christie M; Doyle, Ralph T; Juliano, Rebecca A; Philip, Sephy

2016-09-01

Icosapent ethyl is a high-purity prescription form of eicosapentaenoic acid (EPA) ethyl ester approved at a dose of 4g/day as an adjunct to diet to reduce triglyceride (TG) levels in adult patients with severe (≥500mg/dL) hypertriglyceridemia. This post-hoc exploratory analysis examined the relationship of icosapent ethyl dose with EPA concentrations in plasma and red blood cells (RBCs) across 3 clinical studies-a phase 1 pharmacokinetic study in healthy adult volunteers and 2 pivotal phase 3 studies (MARINE and ANCHOR) in adult patients with hypertriglyceridemia-and examined the relationship between EPA levels and TG-lowering effects in MARINE and ANCHOR. In all 3 studies, icosapent ethyl produced dose-dependent increases in the concentrations of EPA in plasma and RBCs. In both MARINE and ANCHOR, these dose-dependent EPA increases correlated with the degree of TG level lowering (all P<0.01). In patients with high TG levels (≥200mg/dL) and treated with icosapent ethyl 4g/day, the end-of-treatment plasma and RBC EPA concentrations were >170μg/mL and>70μg/mL, respectively. These studies support icosapent ethyl as producing predictable dose-dependent pharmacokinetics/pharmacodynamics, with TG level lowering dependent upon icosapent ethyl dose and EPA concentrations in plasma and RBCs. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

The constitutive production of pectinase by the CT1 mutant of Penicillium occitainis is modulated by pH.

PubMed

Romdhane, Zamen Ben; Tounsi, Hajer; Hadj-Sassi, Azza; Hadj-Taieb, Noomen; Gargouri, Ali

2013-01-01

The aim of the present study was to investigate pectinases production by CT1 mutant of Penicillium occitanis on glucose based media. Two main groups of pectinases were followed: lyases (pectin and pectate lyases) and hydrolases (polygalacturonases and polymethylgalacturonases). When cultivated in different liquid media, where either the starting glucose concentration or the nature of nitrogen sources used was varied, the CT1 mutant secreted either lyases or hydrolases. In fact, the pH of these various media seemed to correlate with the activity produced: The lyases were highly and exclusively produced at neutral or alkaline ambient pH, whereas hydrolases were highly produced on acidic ambient pH. Such conclusion was confirmed by following pectinase production in the same culture medium (with the same glucose concentration and the same nitrogen source) set at two initial pH of 4 and 7. Altogether, these results suggest that the pectinases control by PacC signaling pathway of P. occitanis should resemble to that of Aspergillus and its ability to "activate the expression of alkaline-expressed genes and repress acid-expressed genes" remains intact in the CT1 over-producing and constitutive strain. Enzymes produced at acidic pH (hydrolases) and at neutral pH (lyases) were applied in the hydrolysis of orange peel and gave results comparable to commercial enzymes.

Local bioprospecting for high-lipid producing microalgal strains to be grown on concentrated municipal wastewater for biofuel production.

PubMed

Zhou, Wenguang; Li, Yecong; Min, Min; Hu, Bing; Chen, Paul; Ruan, Roger

2011-07-01

Mass cultivation of microalgae for biofuel production depends heavily on the performance of the microalgae strains used. In this study, 60 algae-like microorganisms collected from different sampling sites in Minnesota were examined using multi-step screening and acclimation procedures to select high-lipid producing facultative heterotrophic microalgae strains capable of growing on concentrated municipal wastewater (CMW) for simultaneous energy crop production and wastewater treatment. Twenty-seven facultative heterotrophic microalgae strains were found, among which 17 strains were proved to be tolerant to CMW. These 17 top-performing strains were identified through morphological observation and DNA sequencing as Chlorella sp., Heynigia sp., Hindakia sp., Micractinium sp., and Scenedesmus sp. Five strains were chosen for other studies because of their ability to adapt to CMW, high growth rates (0.455-0.498 d(-1)) and higher lipid productivities (74.5-77.8 mg L(-1)d(-1)). These strains are considered highly promising compared with other strains reported in the literature. Copyright © 2011 Elsevier Ltd. All rights reserved.

The measurement of radon working levels at a mineral separation pilot plant in Cox's Bazar, Bangladesh.

PubMed

Hamid Khan, M A; Chowdhury, M S

2003-10-01

Beach Sand Exploitation Centre at Cox's Bazar, Bangladesh, produces commercial grade concentrations of magnetite, ilmenite, zircon, etc., from the high-grade accumulations available along the beach and foredune of Cox's Bazar. Solid state nuclear track detectors (CR-39 foils) were used to determine indoor radon concentration of radioactive mineral sands and the technologically enhanced radiation level inside the pilot plant of the Centre. It is found that the concentrations at processed mineral stock areas are high, and the maximum concentration was found to be 2,103 +/- 331 Bq m(-3) (0.23 +/- 0.03 WL). The indoor concentration of radon and its decay products in the raw sand stock area and at other locations was in the range of 116 +/- 27 Bq m(-3) (0.03 +/- 0.003 WL) to 2,042 +/- 233 Bq m(-3) (0.22 +/- 0.03 WL).

Production of Mannitol from a High Concentration of Glucose by Candida parapsilosis SK26.001.

PubMed

Meng, Qing; Zhang, Tao; Wei, Wenting; Mu, Wanmeng; Miao, Ming

2017-01-01

A novel strain, SK26.001, which can produce mannitol from a high concentration of glucose without the addition of fructose, was isolated from sugarcane juice. This strain was identified as Candida parapsilosis based on 18S ribosomal RNA (rRNA) sequence analysis and the morphological and physiological-biochemical characteristics of the strain. Under optimized fermentation conditions, the mannitol concentration in shake flasks reached 68.5 g/L. When batch fermentation was performed, the fed glucose was completely consumed after 72 h, resulting in a final mannitol concentration of 80.3 g/L. Fed-batch fermentation was then performed with glucose feed. During the fed-batch process, ammonia water was added to maintain the pH at 4.0. The mannitol concentration in the fermenter reached 97.1 g/L after 120 h, with a total glucose consumption of 284 g/L.

Study on Treatment of acidic and highly concentrated fluoride waste water using calcium oxide-calcium chloride

NASA Astrophysics Data System (ADS)

Ren, T.; Gao, X. R.; Zheng, T.; Wang, P.

2016-08-01

There are problems with treating acidic waste water containing high concentration fluorine by chemical precipitation, including the low sludge setting velocity and the high difficulty of reaching the criterion. In Heilongjiang province, a graphite factory producing high-purity graphite generates acidic waste water with a high concentration of fluorine. In this paper, the effect of removals on the concentration of fluoride with the combined treatment of calcium oxide and calcium chloride were discussed with regard to acid waste water. The study improved the sludge characteristics by using polyacrylamide (PAM) and polymeric aluminum chloride (PAC). The effect of different coagulants on sludge was evaluated by the sludge settlement ratio (SV), sludge volume index (SVI) and sludge moisture content. The results showed that the optimal combination for 100 ml waste water was calcium oxide addition amount of 14 g, a calcium chloride addition amount of 2.5 g, a PAM addition amount of 350 mg/L, and the effluent fluoride concentration was below 6 mg/L. PAM significantly improved the sludge settling velocity. The sludge settlement ratio reduced from 87.6% to 60%. The process for wastewater treatment was easily operated and involved low expenditure.

Lengthening of Insect Development on Bt Zone Results in Adult Emergence Asynchrony: Does It Influence the Effectiveness of the High Dose/Refuge Zone Strategy?

PubMed Central

Gryspeirt, Aiko; Grégoire, Jean-Claude

2012-01-01

The “High Dose/Refuge” strategy (HD/R) is the currently recommended Insect Resistance Management strategy (IRM) to limit resistance development to Bacillus thuringiensis (Bt) plants. This strategy requires planting a “refuge zone” composed of non-Bt plants suitable for the target insect and in close proximity to a “Bt zone” expressing a high toxin concentration. One of the main assumptions is that enough susceptible adults mate with resistant insects. However, previous studies have suggested that the high toxin concentration produced by Bt plants induces slower insect development, creating an asynchrony in emergence between the refuge and the Bt zone and leading to assortative mating between adults inside each zone. Here, we develop a deterministic model to estimate the impact of toxin concentration, emergence asynchrony and refuge zone size on the effectiveness of the HD/R strategy. We conclude that emergence asynchrony only affects resistance when toxin concentration is high and resistance is recessive. Resistance develops more rapidly and survival of susceptible insects is higher at lower toxin concentration, but in such situations, resistance is insensitive to emergence asynchrony. PMID:23202319

High throughput electrospinning of high-quality nanofibers via an aluminum disk spinneret

NASA Astrophysics Data System (ADS)

Zheng, Guokuo

In this work, a simple and efficient needleless high throughput electrospinning process using an aluminum disk spinneret with 24 holes is described. Electrospun mats produced by this setup consisted of fine fibers (nano-sized) of the highest quality while the productivity (yield) was many times that obtained from conventional single-needle electrospinning. The goal was to produce scaled-up amounts of the same or better quality nanofibers under variable concentration, voltage, and the working distance than those produced with the single needle lab setting. The fiber mats produced were either polymer or ceramic (such as molybdenum trioxide nanofibers). Through experimentation the optimum process conditions were defined to be: 24 kilovolt, a distance to collector of 15cm. More diluted solutions resulted in smaller diameter fibers. Comparing the morphologies of the nanofibers of MoO3 produced by both the traditional and the high throughput set up it was found that they were very similar. Moreover, the nanofibers production rate is nearly 10 times than that of traditional needle electrospinning. Thus, the high throughput process has the potential to become an industrial nanomanufacturing process and the materials processed by it may be used as filtration devices, in tissue engineering, and as sensors.

Classification methods for monitoring Arctic sea ice using OKEAN passive/active two-channel microwave data

USGS Publications Warehouse

Belchansky, Gennady I.; Douglas, David C.

2000-01-01

This paper presents methods for classifying Arctic sea ice using both passive and active (2-channel) microwave imagery acquired by the Russian OKEAN 01 polar-orbiting satellite series. Methods and results are compared to sea ice classifications derived from nearly coincident Special Sensor Microwave Imager (SSM/I) and Advanced Very High Resolution Radiometer (AVHRR) image data of the Barents, Kara, and Laptev Seas. The Russian OKEAN 01 satellite data were collected over weekly intervals during October 1995 through December 1997. Methods are presented for calibrating, georeferencing and classifying the raw active radar and passive microwave OKEAN 01 data, and for correcting the OKEAN 01 microwave radiometer calibration wedge based on concurrent 37 GHz horizontal polarization SSM/I brightness temperature data. Sea ice type and ice concentration algorithms utilized OKEAN's two-channel radar and passive microwave data in a linear mixture model based on the measured values of brightness temperature and radar backscatter, together with a priori knowledge about the scattering parameters and natural emissivities of basic sea ice types. OKEAN 01 data and algorithms tended to classify lower concentrations of young or first-year sea ice when concentrations were less than 60%, and to produce higher concentrations of multi-year sea ice when concentrations were greater than 40%, when compared to estimates produced from SSM/I data. Overall, total sea ice concentration maps derived independently from OKEAN 01, SSM/I, and AVHRR satellite imagery were all highly correlated, with uniform biases, and mean differences in total ice concentration of less than four percent (sd<15%).

Preparing thin aluminum films for adhesive bonding

NASA Technical Reports Server (NTRS)

Smith, T.

1979-01-01

Carbonate pretreatment produces highly bondable surface without harming film. Treatment is useful in developing low-cost mirrors and solar concentrators fabricated from metal-coated plastic films. Treatment should cost no more than standard degreasing and rinsing procedures.

SERS-active silver nanoparticle aggregates produced in high-iron float glass by ion exchange process

NASA Astrophysics Data System (ADS)

Karvonen, L.; Chen, Y.; Säynätjoki, A.; Taiviola, K.; Tervonen, A.; Honkanen, S.

2011-11-01

Silver nanoparticles were produced in iron containing float glasses by silver-sodium ion exchange and post-annealing. In particular, the effect of the concentration and the oxidation state of iron in the host glass on the nanoparticle formation was studied. After the nanoparticle fabrication process, the samples were characterized by optical absorption measurements. The samples were etched to expose nanoparticle aggregates on the surface, which were studied by optical microscopy and scanning electron microscopy. The SERS-activity of these glass samples was demonstrated and compared using a dye molecule Rhodamine 6G (R6G) as an analyte. The importance of the iron oxidation level for reduction process is discussed. The glass with high concentration of Fe 2+ ions was found to be superior in SERS applications of silver nanoparticles. The optimal surface features in terms of SERS enhancement are also discussed.

Comparison of growth factor and platelet concentration from commercial platelet-rich plasma separation systems.

PubMed

Castillo, Tiffany N; Pouliot, Michael A; Kim, Hyeon Joo; Dragoo, Jason L

2011-02-01

Clinical studies claim that platelet-rich plasma (PRP) shortens recovery times because of its high concentration of growth factors that may enhance the tissue repair process. Most of these studies obtained PRP using different separation systems, and few analyzed the content of the PRP used as treatment. This study characterized the composition of single-donor PRP produced by 3 commercially available PRP separation systems. Controlled laboratory study. Five healthy humans donated 100 mL of blood, which was processed to produce PRP using 3 PRP concentration systems (MTF Cascade, Arteriocyte Magellan, Biomet GPS III). Platelet, white blood cell (WBC), red blood cell, and fibrinogen concentrations were analyzed by automated systems in a clinical laboratory, whereas ELISA determined the concentrations of platelet-derived growth factor αβ and ββ (PDGF-αβ, PDGF-ββ), transforming growth factor β1 (TGF-β1), and vascular endothelial growth factor (VEGF). There was no significant difference in mean PRP platelet, red blood cell, active TGF-β1, or fibrinogen concentrations among PRP separation systems. There was a significant difference in platelet capture efficiency. The highest platelet capture efficiency was obtained with Cascade, which was comparable with Magellan but significantly higher than GPS III. There was a significant difference among all systems in the concentrations of WBC, PDGF-αβ, PDGF-ββ, and VEGF. The Cascade system concentrated leukocyte-poor PRP, compared with leukocyte-rich PRP from the GPS III and Magellan systems. The GPS III and Magellan concentrate leukocyte-rich PRP, which results in increased concentrations of WBCs, PDGF-αβ, PDGF-ββ, and VEGF as compared with the leukocyte-poor PRP from Cascade. Overall, there was no significant difference among systems in the platelet concentration, red blood cell, active TGF-β1, or fibrinogen levels. Products from commercially available PRP separation systems produce differing concentrations of growth factors and WBCs. Further research is necessary to determine the clinical relevance of these findings.

Development of an up-grading process to produce MLM structured lipids from sardine discards.

PubMed

Morales-Medina, R; Munio, M; Guadix, A; Guadix, E M

2017-08-01

The aim of the work was to produce MLM structured lipids with caprylic acid (M) as medium chain fatty acid located at the external bonds of the glycerol backbone and concentrated polyunsaturated fatty acids (L) from sardine discards (Sardine pilchardus) in the central bond of the glycerol. To that end, the following steps were conducted: (i) fish oil extraction, (ii) Omega-3 free fatty acids (FFA) concentration (low temperature winterization), (iii) two-steps enzymatic esterification and (iv) triacylglycerols (TAG) purification (liquid column chromatography). The resultant purified triacylglycerols accomplished with the oxidative state (peroxide and anisidine value, PV and AV) required for refined oils. As enzymatic treatment, Omega-3 concentrate FFA (Omega-3>600mg Omega-3 per g oil) were esterified with dicaprylic glycerol employing Novozyme 435. This process presented high regioselectivity, with ∼80mol% of concentrated fatty acids esterified at the sn-2 position. Copyright © 2017 Elsevier Ltd. All rights reserved.

Pathway engineering to improve ethanol production by thermophilic bacteria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lynd, L.R.

1998-12-31

Continuation of a research project jointly funded by the NSF and DOE is proposed. The primary project goal is to develop and characterize strains of C. thermocellum and C. thermosaccharolyticum having ethanol selectivity similar to more convenient ethanol-producing organisms. An additional goal is to document the maximum concentration of ethanol that can be produced by thermophiles. These goals build on results from the previous project, including development of most of the genetic tools required for pathway engineering in the target organisms. As well, we demonstrated that the tolerance of C. thermosaccharolyticum to added ethanol is sufficiently high to allow practicalmore » utilization should similar tolerance to produced ethanol be demonstrated, and that inhibition by neutralizing agents may explain the limited concentrations of ethanol produced in studies to date. Task 1 involves optimization of electrotransformation, using either modified conditions or alternative plasmids to improve upon the low but reproducible transformation, frequencies we have obtained thus far.« less

Integrative assessment of the effects produced by Ag nanoparticles at different levels of biological complexity in Eisenia fetida maintained in two standard soils (OECD and LUFA 2.3).

PubMed

Garcia-Velasco, N; Peña-Cearra, A; Bilbao, E; Zaldibar, B; Soto, M

2017-08-01

There is a potential risk to increase the release of silver nanoparticles (Ag NPs) into the environment: For instance. in soils receiving sludge models estimate 0.007 mg Ag NPs kg -1 that will annually increase due to sludge or sludge incineration residues land-disposal. Thus, the concern about the hazards of nanosilver to soils and soil invertebrates is growing. Studies performed up to now have been focused in traditional endpoints, used limit range concentrations and employed different soil types that differ in physico-chemical characteristics. Presently, effects of Ag NPs have been measured at different levels of biological complexity in Eisenia fetida, exposed for 3 and 14 d to high but sublethal (50 mg Ag NPs kg -1 ) and close to modeled environmental concentrations (0.05 mg Ag NPs kg -1 ). Since characteristics of the exposure matrix may limit the response of the organisms to these concentrations, experiments were carried out in OECD and LUFA soils, the most used standard soils. High concentrations of Ag NPs increased catalase activity and DNA damage in OECD soils after 14 d while in LUFA 2.3 soils produced earlier effects (weight loss, decrease in cell viability and increase in catalase activity at day 3). At day 14, LUFA 2.3 (low clay and organic matter-OM-) could have provoked starvation of earthworms, masking Ag NPs toxicity. The concentration close to modeled environmental concentrations produced effects uniquely in LUFA 2.3 soil. Accurate physico-chemical characteristics of the standard soils are crucial to assess the toxicity exerted by Ag NPs in E. fetida since low clay and OM contents can be considered toxicity enhancers. Copyright © 2017 Elsevier Ltd. All rights reserved.

Vaccine supply: a cross-national perspective.

PubMed

Danzon, Patricia M; Pereira, Nuno Sousa; Tejwani, Sapna S

2005-01-01

In U.S. vaccine markets, competing producers with high fixed, sunk costs face relatively concentrated demand. This tends to lead to exit of all but one or very few producers per vaccine. Detailed evidence of exits and shortages in the flu vaccine market demonstrates the importance of high fixed costs, demand uncertainty, and dynamic quality competition. A comparison of vaccine suppliers in four industrialized countries compared with the United States shows that smaller foreign markets often have more and different vaccine suppliers. High, country-specific, fixed costs, combined with price and volume uncertainty, plausibly deters these potential suppliers from attempting to enter the U.S. market.

Genomic features of Lactococcus lactis IO-1, a lactic acid bacterium that utilizes xylose and produces high levels of L-lactic acid.

PubMed

Shimizu-Kadota, Mariko; Kato, Hiroaki; Shiwa, Yuh; Oshima, Kenshiro; Machii, Miki; Araya-Kojima, Tomoko; Zendo, Takeshi; Hattori, Masahira; Sonomoto, Kenji; Yoshikawa, Hirofumi

2013-01-01

Lactococcus lactis IO-1 (JCM7638) produces L-lactic acid predominantly when grown at high xylose concentrations, and its utilization is highly desired in the green plastics industry. Therefore it is worthwhile studying its genomic traits. In this study, we focused on (i) genes of possible horizontal transfer derivation (prophages, the nisin-sucrose transposon, and several restriction-modification systems), and (ii) genes for the synthetic pathways of amino acids and vitamins in the IO-1 genome. In view of the results of this analysis, we consider their meanings in strain IO-1.

Statistical-thermodynamic model for light scattering from eye lens protein mixtures

NASA Astrophysics Data System (ADS)

Bell, Michael M.; Ross, David S.; Bautista, Maurino P.; Shahmohamad, Hossein; Langner, Andreas; Hamilton, John F.; Lahnovych, Carrie N.; Thurston, George M.

2017-02-01

We model light-scattering cross sections of concentrated aqueous mixtures of the bovine eye lens proteins γB- and α-crystallin by adapting a statistical-thermodynamic model of mixtures of spheres with short-range attractions. The model reproduces measured static light scattering cross sections, or Rayleigh ratios, of γB-α mixtures from dilute concentrations where light scattering intensity depends on molecular weights and virial coefficients, to realistically high concentration protein mixtures like those of the lens. The model relates γB-γB and γB-α attraction strengths and the γB-α size ratio to the free energy curvatures that set light scattering efficiency in tandem with protein refractive index increments. The model includes (i) hard-sphere α-α interactions, which create short-range order and transparency at high protein concentrations, (ii) short-range attractive plus hard-core γ-γ interactions, which produce intense light scattering and liquid-liquid phase separation in aqueous γ-crystallin solutions, and (iii) short-range attractive plus hard-core γ-α interactions, which strongly influence highly non-additive light scattering and phase separation in concentrated γ-α mixtures. The model reveals a new lens transparency mechanism, that prominent equilibrium composition fluctuations can be perpendicular to the refractive index gradient. The model reproduces the concave-up dependence of the Rayleigh ratio on α/γ composition at high concentrations, its concave-down nature at intermediate concentrations, non-monotonic dependence of light scattering on γ-α attraction strength, and more intricate, temperature-dependent features. We analytically compute the mixed virial series for light scattering efficiency through third order for the sticky-sphere mixture, and find that the full model represents the available light scattering data at concentrations several times those where the second and third mixed virial contributions fail. The model indicates that increased γ-γ attraction can raise γ-α mixture light scattering far more than it does for solutions of γ-crystallin alone, and can produce marked turbidity tens of degrees celsius above liquid-liquid separation.

Damage to cochlear efferents following AF64A intoxication.

PubMed

Smith, D W; Mount, R J

1993-07-01

Damage to cochlear efferents in chinchillas was assessed using transmission electron microscopy following unilateral treatment with the cholinotoxin ethylcholine mustard aziridinium ion (AF64A). AF64A was diluted in artificial perilymph to concentrations ranging from 0.5 to 100 microM. Survival times ranged from 1 to 12 weeks. At concentrations above 10 microM, widespread damage was noted to efferent fibers within the inner spiral bundle (ISB), tunnel spiral bundle (TSB), tunnel radial fibers (TRF) and efferent terminals at the base of OHCs. This damage included degeneration of fibers and terminals, delamination of mitochondria, vacuolization, and loss of cell membrane. However, at high concentrations, non-specific damage was also noted as thinnings or discontinuities of the membrane of OHCs and afferent fibers. At concentrations between 3 and 10 microM, selective damage was observed to efferent fibers within the ISB, TSB, TRF, and to terminals at the base of the OHCs, with all other structures appearing normal. At concentrations of 0.5 and 1 microM, damage was limited to efferent fibers within the TSB and ISB below the inner hair cells. In general, insult was greatest to middle- and basal-turn efferents, and longer survival times did not produce greater damage to, or loss of, efferents. These data suggest that at low concentrations, AF64A produces a partial yet selective degeneration of cochlear efferents within both the medial and lateral tracts, and that at the lowest concentrations used in these studies, AF64A produces a preferential insult on lateral olivocochlear efferents.

Determination of physiochemical properties of palm oil methyl ester catalyzed by waste cockle shells

NASA Astrophysics Data System (ADS)

Nasir, Nurul Fitriah; Latif, Noradila Abdul; Bakar, Sharifah Adzila Syed Abu; Rahman, Mohd Nasrull Abdul; Selamat, Siti Norhidayah; Nasharudin, Nurul Nadirah

2017-04-01

Waste cockle shell can be used as a source of calcium oxide (CaO) in catalyzing a transesterification reaction to produce biodiesel or fatty acid methyl ester (FAME). This aim of this paper is to determine the physicochemical properties of (FAME) which utilize waste cockle shells in the transesterification reaction process. In this study, the catalyst was prepared using high temperature furnace (700°C) for 4 h. The molar ratio of methanol to oil was fixed at 9:1 and the reaction temperature and catalyst concentration were varied from 65 -70 °C, and 10-30 wt. %, respectively for transesterification reaction. The reaction time was also fixed at 3 h. The analyzed physicochemical properties were density, viscosity, flash point and net heat of combustion. The results obtained from the analysis found that reaction temperature 65°C with 30% of catalyst concentration has produced the physical properties of FAME that comply the biodiesel standards. The results suggest that reaction temperature and catalyst concentration have influence on the value of physicochemical properties of FAME produced.

A marine secondary producer respires and feeds more in a high CO2 ocean.

PubMed

Li, Wei; Gao, Kunshan

2012-04-01

Climate change mediates marine chemical and physical environments and therefore influences marine organisms. While increasing atmospheric CO(2) level and associated ocean acidification has been predicted to stimulate marine primary productivity and may affect community structure, the processes that impact food chain and biological CO(2) pump are less documented. We hypothesized that copepods, as the secondary marine producer, may respond to future changes in seawater carbonate chemistry associated with ocean acidification due to increasing atmospheric CO(2) concentration. Here, we show that the copepod, Centropages tenuiremis, was able to perceive the chemical changes in seawater induced under elevated CO(2) concentration (>1700 μatm, pH<7.60) with avoidance strategy. The copepod's respiration increased at the elevated CO(2) (1000 μatm), associated acidity (pH 7.83) and its feeding rates also increased correspondingly, except for the initial acclimating period, when it fed less. Our results imply that marine secondary producers increase their respiration and feeding rate in response to ocean acidification to balance the energy cost against increased acidity and CO(2) concentration. Copyright © 2012 Elsevier Ltd. All rights reserved.

Direct utilization of waste water algal biomass for ethanol production by cellulolytic Clostridium phytofermentans DSM1183.

PubMed

Fathima, Anwar Aliya; Sanitha, Mary; Kumar, Thangarathinam; Iyappan, Sellamuthu; Ramya, Mohandass

2016-02-01

Direct bioconversion of waste water algal biomass into ethanol using Clostridium phytofermentans DSM1183 was demonstrated in this study. Fermentation of 2% (w/v) autoclaved algal biomass produced ethanol concentration of 0.52 g L(-1) (solvent yield of 0.19 g/g) where as fermentation of acid pretreated algal biomass (2%, w/v) produced ethanol concentration of 4.6 g L(-1) in GS2 media (solvent yield of 0.26 g/g). The control experiment with 2% (w/v) glucose in GS2 media produced ethanol concentration of 2.8 g L(-1) (solvent yield of 0.25 g/g). The microalgal strains from waste water algal biomass were identified as Chlamydomonas dorsoventralis, Graesiella emersonii, Coelastrum proboscideum, Scenedesmus obliquus, Micractinium sp., Desmodesmus sp., and Chlorella sp., based on ITS-2 molecular marker. The presence of glucose, galactose, xylose and rhamnose were detected by high performance liquid chromatography in the algal biomass. Scanning Electron Microscopy observations of fermentation samples showed characteristic morphological changes in algal cells and bioaccessibility of C. phytofermentans. Copyright © 2015 Elsevier Ltd. All rights reserved.

Characterization of ambient particles size in workplace of manufacturing physical fitness equipments

PubMed Central

LIN, Chih-Chung; CHEN, Mei-Ru; CHANG, Sheng-Lang; LIAO, Wei-Heng; CHEN, Hsiu-Ling

2014-01-01

The manufacturing of fitness equipment involves several processes, including the cutting and punching of iron tubes followed by welding. Welding operations produce hazardous gases and particulate matter, which can enter the alveolar, resulting in adverse health effects. This study sought to verify the particle size distribution and exposure concentrations of atmospheric air samples in various work areas of a fitness equipment manufacturing industry. Observed particle concentrations are presented by area and in terms of relative magnitude: painting (15.58 mg/m3) > automatic welding (0.66 mg/m3) > manual welding (0.53 mg/m3) > punching (0.18 mg/m3) > cutting (0.16 mg/m3). The concentrations in each of the five work areas were Cinh>Cthor>Cresp. In all areas except the painting area, extra-fine particles produced by welding at high temperatures, and further those coagulated to form larger particles. This study observed bimodal distribution in the size of welding fume in the ranges of 0.7–1 µm and 15–21 µm. Meanwhile, the mass concentrations of particles with different sizes were not consistent across work areas. In the painting area, the mass concentration was higher in Chead>Cth>Calv, but in welding areas, it was found that Calv>Chead>Cth. Particles smaller than 1µm were primarily produced by welding. PMID:25327301

Contractile activity of ATP and diadenosine tetraphosphate on urinary bladder in the rats: role of superoxide anion and urothelium.

PubMed

Khattab, M M; Al-Hrasen, M N

2006-04-01

Both ATP and diadenosine tetraphosphate (AP(4)A) produced a dose-dependent contraction of rat isolated urinary bladder rings. The AP(4)A dose-response curve was to the left of that of ATP, and the maximum response was greater than that produced by ATP. Mechanical removal of the urothelium increased the contractile response to ATP by between 53% and 71%, and that to AP(4)A by 42% (at highest AP(4)A concentration) to 68% at lower concentration. Inhibition of Cu/Zn superoxide dismutase with diethylthiocarbamate (DETCA, 5 mm) significantly reduced the ATP-evoked contraction by 31% (at high ATP concentration) to 40% at low ATP concentration. Similarly, the AP(4)A-induced contractions were significantly decreased by 27% at low AP(4)A level to 38% at higher concentrations. Induction of exogenous superoxide anion stress by the use of the superoxide anion generator, pyrogallol (0.5 mm), significantly decreased both ATP- and AP(4)A-induced contractions of the rat urinary bladder over the whole dose range. Contractile responses to ATP decreased by 36-40%, and those to AP(4)A by 44-49%. In conclusion, the urinary bladder urothelium exerts an inhibitory control over the purinergic contractility produced by adenine mononucleotides and dinucleotides. Superoxide anion stress, whether endogenous or exogenous, attenuates the ATP-induced as well as AP(4)A-induced contractility.

Determination of boron in produced water using the carminic acid assay.

PubMed

Floquet, Cedric F A; Sieben, Vincent J; MacKay, Bruce A; Mostowfi, Farshid

2016-04-01

Using the carminic acid assay, we determined the concentration of boron in oilfield waters. We investigated the effect of high concentrations of salts and dissolved metals on the assay performance. The influence of temperature, development time, reagent concentration, and water volume was studied. Ten produced and flowback water samples of different origins were measured, and the method was successfully validated against ICP-MS measurements. In water-stressed regions, produced water is a potential source of fresh water for irrigation, industrial applications, or consumption. Therefore, boron concentration must be determined and controlled to match the envisaged waste water reuse. Fast, precise, and onsite measurements are needed to minimize errors introduced by sample transportation to laboratories. We found that the optimum conditions for our application were a 5:1 mixing volume ratio (reagent to sample), a 1 g L(-1) carminic acid concentration in 99.99% sulfuric acid, and a 30 min reaction time at ambient temperature (20 °C to 23 °C). Absorption values were best measured at 610 nm and 630 nm and baseline corrected at 865 nm. Under these conditions, the sensitivity of the assay to boron was maximized while its cross-sensitivity to dissolved titanium, iron, barium and zirconium was minimized, alleviating the need for masking agents and extraction methods. Copyright © 2015 Elsevier B.V. All rights reserved.

Uranium hydrogeochemical and stream sediment reconnaissance of the Newcastle NTMS Quadrangle, Wyoming, including concentrations of forty-two additional elements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goff, S.J.; Sandoval, W.F.; Gallimore, D.L.

1980-06-01

Water and sediment samples were collected and each water sample was analyzed for U, and each sediment sample was analyzed for 43 elements, including U and Th. Uranium concentrations in water samples range from below the detection limit of 0.02 ppB to 702.26 ppB and have a median of 1.73 ppB and a mean of 11.76 ppB. Water samples containing high uranium concentrations generally are associated with known uranium mining activity or units known to be uranium bearing. About one-third of the water samples containing high uranium concentrations were collected from locations within the Pumpkin Buttes and Turnercrest-Ross Districts. Nearlymore » half of the water samples containing high uranium concentrations were collected from locations just west of the Monument Hill and Highland Flats-Box Creek Districts. Similar anomalous uranium concentrations in this region have been reported updip from Exxon's Highland uranium deposits. High uranium concentrations were also found associated with the Lance Creek-Old Woman Anticline District. Uranium concentrations in sediment samples range from 1.14 to 220.70 ppM and have a median of 3.37 ppM and a mean of 4.03 ppM. Throughout the major uranium mining districts of the Powder River Basin, sediment samples with high uranium concentrations were collected from dry streams located near wells producing water samples with high uranium concentrations. High uranium concentrations were also found associated with the Lance Creek oil field where uranium mineralization is known in the White River formation. High uranium concentrations were also found in sediment samples in areas where uranium mineralization is not known. These samples are from dry streams in areas underlain by the White River formation, the Niobrara formation, and the Pierre, Carlisle, Belle Fourche, and Mowry shales.« less

The use of fluoride as a natural tracer in water and the relationship to geological features: Examples from the Animas River Watershed, San Juan Mountains, Silverton, Colorado

USGS Publications Warehouse

Bove, D.J.; Walton-Day, K.; Kimball, B.A.

2009-01-01

Investigations within the Silverton caldera, in southwestern Colorado, used a combination of traditional geological mapping, alteration-assemblage mapping, and aqueous geochemical sampling that showed a relationship between geological and hydrologic features that may be used to better understand the provenance and evolution of the water. Veins containing fluorite, huebnerite, and elevated molybdenum concentrations are temporally and perhaps genetically associated with the emplacement of high-silica rhyolite intrusions. Both the rhyolites and the fluorite-bearing veins produce waters containing elevated concentrations of F-, K and Be. The identification of water samples with elevated F/Cl molar ratios (> 10) has also aided in the location of water draining F-rich sources, even after these waters have been diluted substantially. These unique aqueous geochemical signatures can be used to relate water chemistry to key geological features and mineralized source areas. Two examples that illustrate this relationship are: (1) surface-water samples containing elevated F-concentrations (> 1.8 mg/l) that closely bracket the extent of several small high-silica rhyolite intrusions; and (2) water samples containing elevated concentrations of F-(> 1.8 mg/ l) that spatially relate to mines or areas that contain late-stage fluorite/huebnerite veins. In two additional cases, the existence of high F-concentrations in water can be used to: (1) infer interaction of the water with mine waste derived from systems known to contain the fluorite/huebnerite association; and (2) relate changes in water quality over time at a high elevation mine tunnel to plugging of a lower elevation mine tunnel and the subsequent rise of the water table into mineralized areas containing fluorite/huebnerite veining. Thus, the unique geochemical signature of the water produced from fluorite veins indicates the location of high-silica rhyolites, mines, and mine waste containing the veins. Existence of high F-concentrations along with K and Be in water in combination with other geological evidence may be used to better understand the provenance of the water. ?? 2009 AAG/Geological Society of London.

Production and characterization of streptomycin dependent mutants of Pasteurella multocida from bovine haemorrhagic septicaemia.

PubMed Central

de Alwis, M C; Carter, G R; Chengappa, M M

1980-01-01

A large number of streptomycin dependent mutants were produced from bovine haemorrhagic septicaemia strains of Pasteurella multocida. The mutants required a minimum concentration of 25-50 microgram/mL streptomycin for growth and tolerated a concentration of 200 mg/mL. These mutants were avirulent to mice, when inoculated alone, but some mutants killed mice when inoculated with streptomycin. Biochemically all mutants were uniform and similar to the wild type. Most mutants were stable, but a few produced streptomycin independent revertants. The rate of reversion varied with each mutant. Most revertants were highly virulent for mice, some totally avirulant and a few relatively avirulent. PMID:6778598

MHD conversion of solar energy. [space electric power system

NASA Technical Reports Server (NTRS)

Lau, C. V.; Decher, R.

1978-01-01

Low temperature plasmas wherein an alkali metal vapor is a component are uniquely suited to simultaneously absorb solar radiation by coupling to the resonance lines and produce electrical power by the MHD interaction. This work is an examination of the possibility of developing space power systems which take advantage of concentrated solar power to produce electricity. It is shown that efficient cycles in which expansion work takes place at nearly constant top cycle temperature can be devised. The power density of the solar MHD generator is lower than that of conventional MHD generators because of the relatively high seed concentration required for radiation absorption and the lower flow velocity permitted to avoid total pressure losses due to heating.

Rationale behind the near-ideal catalysis of Candida antarctica lipase A (CAL-A) for highly concentrating ω-3 polyunsaturated fatty acids into monoacylglycerols.

PubMed

He, Yongjin; Li, Jingbo; Kodali, Sitharam; Chen, Bilian; Guo, Zheng

2017-03-15

Dramatic decline in the quality and quantity of ω-3 PUFAs from marine resource demands new environmental-friendly technology to produce high quality ω-3 PUFAs concentrates in a better bioavailable form. Accordingly this work demonstrated an exceptionally highly efficient non-aqueous approach that non-regiospecific and non ω-3 PUFAs preferential Candida antarctica lipase A (CAL-A), functioning as a near-ideal biocatalyst, is capable to directly concentrate ω-3 PUFAs from 20% to 30% in oils to up to >90% in monoacylglycerols form through one step reaction. The rationale behind the experimental observation is justified and the catalytic property and specificity of an ideal enzyme tackling this task are defined. High selectivity and efficiency, excellent reusability of biocatalyst, general applicability for concentrating ω-3 PUFAs from both fish and microalgae oils, simple process for product recovery (e.g. by short path distillation), make this novel approach a highly industrially relevant and with potential application in food and drug industries. Copyright © 2016 Elsevier Ltd. All rights reserved.

High-throughput method to predict extrusion pressure of ceramic pastes.

PubMed

Cao, Kevin; Liu, Yang; Tucker, Christopher; Baumann, Michael; Grit, Grote; Lakso, Steven

2014-04-14

A new method was developed to measure the rheology of extrudable ceramic pastes using a Hamilton MicroLab Star liquid handler. The Hamilton instrument, normally used for high throughput liquid processing, was expanded to function as a low pressure capillary rheometer. Diluted ceramic pastes were forced through the modified pipettes, which produced pressure drop data that was converted to standard rheology data. A known ceramic paste containing cellulose ether was made and diluted to various concentrations in water. The most dilute paste samples were tested in the Hamilton instrument and the more typical, highly concentrated, ceramic paste were tested with a hydraulic ram extruder fitted with a capillary die and pressure measurement system. The rheology data from this study indicates that the dilute high throughput method using the Hamilton instrument correlates to, and can predict, the rheology of concentrated ceramic pastes normally used in ceramic extrusion production processes.

Intense ion beam generator

DOEpatents

Humphries, Jr., Stanley; Sudan, Ravindra N.

1977-08-30

Methods and apparatus for producing intense megavolt ion beams are disclosed. In one embodiment, a reflex triode-type pulsed ion accelerator is described which produces ion pulses of more than 5 kiloamperes current with a peak energy of 3 MeV. In other embodiments, the device is constructed so as to focus the beam of ions for high concentration and ease of extraction, and magnetic insulation is provided to increase the efficiency of operation.

Combining In-situ Measurements, Passive Satellite Imagery, and Active Radar Retrievals for the Detection of High Ice Water Content

NASA Astrophysics Data System (ADS)

Yost, C. R.; Minnis, P.; Bedka, K. M.; Nguyen, L.; Palikonda, R.; Spangenberg, D.; Strapp, J. W.; Delanoë, J.; Protat, A.

2016-12-01

At least one hundred jet engine power loss events since the 1990s have been attributed to the phenomenon known as ice crystal icing (ICI). Ingestion of high concentrations of ice particles into aircraft engines is thought to cause these events, but it is clear that the use of current on-board weather radar systems alone is insufficient for detecting conditions that might cause ICI. Passive radiometers in geostationary orbit are valuable for monitoring systems that produce high ice water content (HIWC) and will play an important role in nowcasting, but are incapable of making vertically resolved measurements of ice particle concentration, i.e., ice water content (IWC). Combined radar, lidar, and in-situ measurements are essential for developing a skilled satellite-based HIWC nowcasting technique. The High Altitude Ice Crystals - High Ice Water Content (HAIC-HIWC) field campaigns in Darwin, Australia, and Cayenne, French Guiana, have produced a valuable dataset of in-situ total water content (TWC) measurements with which to study conditions that produce HIWC. The NASA Langley Satellite ClOud and Radiative Property retrieval System (SatCORPS) was used to derive cloud physical and optical properties such cloud top height, temperature, optical depth, and ice water path from multi-spectral satellite imagery acquired throughout the HAIC-HIWC campaigns. These cloud properties were collocated with the in-situ TWC measurements in order to characterize cloud properties in the vicinity of HIWC. Additionally, a database of satellite-derived overshooting cloud top (OT) detections was used to identify TWC measurements in close proximity to convective cores likely producing large concentrations of ice crystals. Certain cloud properties show some sensitivity to increasing TWC and a multivariate probabilistic indicator of HIWC was developed from these datasets. This paper describes the algorithm development and demonstrates the HIWC indicator with imagery from the HAIC-HIWC campaigns. Vertically resolved IWC retrievals from active sensors such as the Cloud Profiling Radar (CPR) on CloudSat and the Doppler Radar System Airborne (RASTA) provide IWC profiles with which to validate and potentially enhance the satellite-based HIWC indicator.

Forward osmosis for the treatment of reverse osmosis concentrate from water reclamation: process performance and fouling control.

PubMed

Kazner, C; Jamil, S; Phuntsho, S; Shon, H K; Wintgens, T; Vigneswaran, S

2014-01-01

While high quality water reuse based on dual membrane filtration (membrane filtration or ultrafiltration, followed by reverse osmosis) is expected to be progressively applied, treatment and sustainable management of the produced reverse osmosis concentrate (ROC) are still important issues. Forward osmosis (FO) is a promising technology for maximising water recovery and further dewatering ROC so that zero liquid discharge is produced. Elevated concentrations of organic and inorganic compounds may act as potential foulants of the concentrate desalting system, in that they consist of, for example, FO and a subsequent crystallizer. The present study investigated conditions under which the FO system can serve as concentration phase with the focus on its fouling propensity using model foulants and real ROC. Bulk organics from ROC consisted mainly of humic acids (HA) and building blocks since wastewater-derived biopolymers were retained by membrane filtration or ultrafiltration. Organic fouling of the FO system by ROC-derived bulk organics was low. HA was only adsorbed moderately at about 7% of the initial concentration, causing a minor flux decline of about 2-4%. However, scaling was a major impediment to this process if not properly controlled, for instance by pH adjustment or softening.

Lithium

USGS Publications Warehouse

Ober, J.

1998-01-01

The lithium industry can be divided into two sectors: ore concentrate producers and chemical producers. Ore concentrate producers mine lithium minerals. They beneficiate the ores to produce material for use in ceramics and glass manufacturing.

Screening and characterization of ethanol-tolerant and thermotolerant acetic acid bacteria from Chinese vinegar Pei.

PubMed

Chen, Yang; Bai, Ye; Li, Dongsheng; Wang, Chao; Xu, Ning; Hu, Yong

2016-01-01

Acetic acid bacteria (AAB) are important microorganisms in the vinegar industry. However, AAB have to tolerate the presence of ethanol and high temperatures, especially in submerged fermentation (SF), which inhibits AAB growth and acid yield. In this study, seven AAB that are tolerant to temperatures above 40 °C and ethanol concentrations above 10% (v/v) were isolated from Chinese vinegar Pei. All the isolated AAB belong to Acetobacter pasteurianus according to 16S rDNA analysis. Among all AAB, AAB4 produced the highest acid yield under high temperature and ethanol test conditions. At 4% ethanol and 30-40 °C temperatures, AAB4 maintained an alcohol-acid transform ratio of more than 90.5 %. High alcohol-acid transform ratio was still maintained even at higher temperatures, namely, 87.2, 77.1, 14.5 and 2.9% at 41, 42, 43 and 44 °C, respectively. At 30 °C and different initial ethanol concentrations (4-10%), the acid yield by AAB4 increased gradually, although the alcohol-acid transform ratio decreased to some extent. However, 46.5, 8.7 and 0.9% ratios were retained at ethanol concentrations of 11, 12 and 13%, respectively. When compared with AS1.41 (an AAB widely used in China) using a 10 L fermentor, AAB4 produced 42.0 g/L acetic acid at 37 °C with 10% ethanol, whereas AS1.41 almost stopped producing acetic acid. In conclusion, these traits suggest that AAB4 is a valuable strain for vinegar production in SF.

The Effect of the Concentration of Oxidant, Cr(VI), on the Iron Oxidation in Saline Water

NASA Astrophysics Data System (ADS)

Ahn, H.; Jo, H. Y.; Ryu, J. H.; Koh, Y. K.

2014-12-01

Deep geological disposal is currently considered as the most appropriate method to isolate high level radioactive wastes (HLRWs) from the ecosystem. If groundwater seeps into underground disposal facilities, water molecules can be dissociated to radicals or peroxides, which can oxidize metal canisters and HLRWs. The oxidized radionuclides with a high solubility can be dissolved in the groundwater. Some dissolved radionuclides can act as oxidants. The continuous radiolysis of water molecules, which results from continuous seepage of groundwater, can enable the continuous production of the radioactive oxidants, resulting in an increase in concentration of oxidants. In this study, the effect of oxidant concentration on iron oxidation in the presence of salt was evaluated. Zero valent iron (ZVI) particles were reacted with Cr(VI) solutions with initial Cr(VI) concentrations ranged from 50 to 300 mg/L in reactors. The initial pH and NaCl concentration were fixed at 3 and 0.5 M, respectively. An increase in the initial Cr(VI) concentration caused an increase in the rate and extend of H2 gas production. The decrement of Cr(VI) was increased as the initial Cr(VI) concentration was increased. The penetration of H+ ions in the presence Cl- ions through the passive film on the ZVI particles caused the reaction between H+ ions and ZVI particles, producing H2 gas and Fe2+ ions. The passive film was damaged during the reaction due to the eruption of H2 gas or peptization by Cl- ions. The Fe2+ ions were reacted with Cr(VI) ions in the solution, producing Fe(III)-Cr(III) (oxy)hydroxides on the passive film of ZVI particles or in the solution as colloidal particles. The Fe(III)-Cr(III) (oxy)hydroxides tends to be precipitated as colloidal particles at a high Cr(VI) concentration and precipitated on the passive film at a low Cr(VI) concentration. The passive film was repaired or thickened by additional formation of Fe(III)-Cr(III) (oxy)hydroxides at a lower Cr(VI) concentration.

Ice nucleation and dehydration in the Tropical Tropopause Layer.

PubMed

Jensen, Eric J; Diskin, Glenn; Lawson, R Paul; Lance, Sara; Bui, T Paul; Hlavka, Dennis; McGill, Matthew; Pfister, Leonhard; Toon, Owen B; Gao, Rushan

2013-02-05

Optically thin cirrus near the tropical tropopause regulate the humidity of air entering the stratosphere, which in turn has a strong influence on the Earth's radiation budget and climate. Recent high-altitude, unmanned aircraft measurements provide evidence for two distinct classes of cirrus formed in the tropical tropopause region: (i) vertically extensive cirrus with low ice number concentrations, low extinctions, and large supersaturations (up to ∼70%) with respect to ice; and (ii) vertically thin cirrus layers with much higher ice concentrations that effectively deplete the vapor in excess of saturation. The persistent supersaturation in the former class of cirrus is consistent with the long time-scales (several hours or longer) for quenching of vapor in excess of saturation given the low ice concentrations and cold tropical tropopause temperatures. The low-concentration clouds are likely formed on a background population of insoluble particles with concentrations less than 100 L(-1) (often less than 20 L(-1)), whereas the high ice concentration layers (with concentrations up to 10,000 L(-1)) can only be produced by homogeneous freezing of an abundant population of aqueous aerosols. These measurements, along with past high-altitude aircraft measurements, indicate that the low-concentration cirrus occur frequently in the tropical tropopause region, whereas the high-concentration cirrus occur infrequently. The predominance of the low-concentration clouds means cirrus near the tropical tropopause may typically allow entry of air into the stratosphere with as much as ∼1.7 times the ice saturation mixing ratio.

Measuring Hydrogen Concentrations in Metals

NASA Technical Reports Server (NTRS)

Danford, M. D.

1985-01-01

Commercial corrosion-measurement system adapted to electrochemical determination of hydrogen concentrations in metals. New technique based on diffusion of hydrogen through foil specimen of metal. In sample holder, hydrogen produced on one side of foil, either by corrosion reaction or by cathodic current. Hydrogen diffused through foil removed on other side by constant anode potential, which leads to oxidation of hydrogen to water. Anode current is measure of concentration of hydrogen diffusing through foil. System used to study hydrogen uptake, hydrogen elimination by baking, effect of heat treatment, and effect of electroplating on high-strength steels.

Development of a small-sized generator of ozonated water using an electro-conductive diamond electrode.

PubMed

Sekido, Kota; Kitaori, Noriyuki

2008-12-01

A small-sized generator of ozonated water was developed using an electro-conductive diamond. We studied the optimum conditions for producing ozonated water. As a result, we developed a small-sized generator of ozonated water driven by a dry-cell for use in the average household. This generator was easily able to produce ozonated water with an ozone concentration (over 4 mg/L) sufficient for disinfection. In addition, we verified the high disinfecting performance of the water produced in an actual hospital.

Raman spectroscopic analysis of the increase of the carotenoid antioxidant concentration in human skin after a 1-week diet with ecological eggs

NASA Astrophysics Data System (ADS)

Hesterberg, Karoline; Lademann, Jürgen; Patzelt, Alexa; Sterry, Wolfram; Darvin, Maxim E.

2009-03-01

Skin aging is mainly caused by the destructive action of free radicals, produced by the UV light of the sun. The human skin has developed a protection system against these highly reactive molecules in the form of the antioxidative potential. Carotenoids are one of the main components of the antioxidants of the human skin. From former studies, it is known that skin aging is reduced in individuals with high levels of carotenoids. Because most of the antioxidants cannot be produced by the human organism, they must be up taken by nutrition. Using noninvasive Raman spectroscopic measurements it is demonstrated that not only fruits and vegetables but also eggs contain high concentrations of antioxidants including carotenoids, which are even doubled in the case of ecological eggs. After a 1-week diet with ecological eggs performed by six volunteers, it is found that the concentration of the carotenoids in the skin of the volunteers increased by approx. 20%. Our study does not intend to recommend exorbitant egg consumption, as eggs also contain harmful cholesterol. But in the case of egg consumption, ecological eggs from hens kept on pasture should be preferred to also receive a benefit for the skin.

Role of hexose transport in control of glycolytic flux in Saccharomyces cerevisiae.

PubMed

Elbing, Karin; Larsson, Christer; Bill, Roslyn M; Albers, Eva; Snoep, Jacky L; Boles, Eckhard; Hohmann, Stefan; Gustafsson, Lena

2004-09-01

The yeast Saccharomyces cerevisiae predominantly ferments glucose to ethanol at high external glucose concentrations, irrespective of the presence of oxygen. In contrast, at low external glucose concentrations and in the presence of oxygen, as in a glucose-limited chemostat, no ethanol is produced. The importance of the external glucose concentration suggests a central role for the affinity and maximal transport rates of yeast's glucose transporters in the control of ethanol production. Here we present a series of strains producing functional chimeras between the hexose transporters Hxt1 and Hxt7, each of which has distinct glucose transport characteristics. The strains display a range of decreasing glycolytic rates resulting in a proportional decrease in ethanol production. Using these strains, we show for the first time that at high glucose levels, the glucose uptake capacity of wild-type S. cerevisiae does not control glycolytic flux during exponential batch growth. In contrast, our chimeric Hxt transporters control the rate of glycolysis to a high degree. Strains whose glucose uptake is mediated by these chimeric transporters will undoubtedly provide a powerful tool with which to examine in detail the mechanism underlying the switch between fermentation and respiration in S. cerevisiae and will provide new tools for the control of industrial fermentations.

Role of Hexose Transport in Control of Glycolytic Flux in Saccharomyces cerevisiae

PubMed Central

Elbing, Karin; Larsson, Christer; Bill, Roslyn M.; Albers, Eva; Snoep, Jacky L.; Boles, Eckhard; Hohmann, Stefan; Gustafsson, Lena

2004-01-01

The yeast Saccharomyces cerevisiae predominantly ferments glucose to ethanol at high external glucose concentrations, irrespective of the presence of oxygen. In contrast, at low external glucose concentrations and in the presence of oxygen, as in a glucose-limited chemostat, no ethanol is produced. The importance of the external glucose concentration suggests a central role for the affinity and maximal transport rates of yeast's glucose transporters in the control of ethanol production. Here we present a series of strains producing functional chimeras between the hexose transporters Hxt1 and Hxt7, each of which has distinct glucose transport characteristics. The strains display a range of decreasing glycolytic rates resulting in a proportional decrease in ethanol production. Using these strains, we show for the first time that at high glucose levels, the glucose uptake capacity of wild-type S. cerevisiae does not control glycolytic flux during exponential batch growth. In contrast, our chimeric Hxt transporters control the rate of glycolysis to a high degree. Strains whose glucose uptake is mediated by these chimeric transporters will undoubtedly provide a powerful tool with which to examine in detail the mechanism underlying the switch between fermentation and respiration in S. cerevisiae and will provide new tools for the control of industrial fermentations. PMID:15345416

Secretomic Insight into Glucose Metabolism of Aspergillus brasiliensis in Solid-State Fermentation.

PubMed

Volke-Sepulveda, Tania; Salgado-Bautista, Daniel; Bergmann, Carl; Wells, Lance; Gutierrez-Sanchez, Gerardo; Favela-Torres, Ernesto

2016-10-07

The genus Aspergillus is ubiquitous in nature and includes various species extensively exploited industrially due to their ability to produce and secrete a variety of enzymes and metabolites. Most processes are performed in submerged fermentation (SmF); however, solid-state fermentation (SSF) offers several advantages, including lower catabolite repression and substrate inhibition and higher productivity and stability of the enzymes produced. This study aimed to explain the improved metabolic behavior of A. brasiliensis ATCC9642 in SSF at high glucose concentrations through a proteomic approach. Online respirometric analysis provided reproducible samples for secretomic studies when the maximum CO 2 production rate occurred, ensuring consistent physiological states. Extracellular extracts from SSF cultures were treated by SDS-PAGE, digested with trypsin, and analyzed by LC-MS/MS. Of 531 sequences identified, 207 proteins were analyzed. Twenty-five were identified as the most abundant unregulated proteins; 87 were found to be up-regulated and 95 were down-regulated with increasing glucose concentration. Of the regulated proteins, 120 were enzymes, most involved in the metabolism of carbohydrates (51), amino acids (23), and nucleotides (9). This study shows the high protein secretory activity of A. brasiliensis under SSF conditions. High glucose concentration favors catabolic activities, while some stress-related proteins and those involved in proteolysis are down-regulated.

Characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil.

PubMed

Song, Geum-Ju; Seo, Yong-Chil; Pudasainee, Deepak; Kim, In-Tae

2010-07-01

An attempt has been made to recover high-calorific fuel gas and useful carbonaceous residue by the electric arc pyrolysis of waste lubricating oil. The characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil were investigated in this study. The produced gas was mainly composed of hydrogen (35-40%), acetylene (13-20%), ethylene (3-4%) and other hydrocarbons, whereas the concentration of CO was very low. Calorific values of gas ranged from 11,000 to 13,000 kcal kg(-1) and the concentrations of toxic gases, such as NO(x), HCl and HF, were below the regulatory emissions limit. Gas chromatography-mass spectrometry (GC/MS) analysis of liquid-phase residues showed that high molecular-weight hydrocarbons in waste lubricating oil were pyrolyzed into low molecular-weight hydrocarbons and hydrogen. Dehydrogenation was found to be the main pyrolysis mechanism due to the high reaction temperature induced by electric arc. The average particle size of soot as carbonaceous residue was about 10 microm. The carbon content and heavy metals in soot were above 60% and below 0.01 ppm, respectively. The utilization of soot as industrial material resources such as carbon black seems to be feasible after refining and grinding. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

Environmental chemistry of animal manure

USDA-ARS?s Scientific Manuscript database

Animal manure is traditionally regarded as a valuable resource of plant nutrients. However, there is an increasing environmental concern associated with animal manure utilization due to high and locally concentrated volumes of manure produced in modern intensified animal production. Although conside...

The Revised Edition of Korean Calendar for Allergenic Pollens

PubMed Central

Lee, Ha-Baik; Kang, Im-Joo; Kim, Seong-Won; Park, Kang-Seo; Kook, Myung-Hee; Kim, Bong-Seong; Baek, Hey-Sung; Kim, Joo-Hwa; Kim, Ja-Kyung; Lee, Dong-Jin; Kim, Kyu-Rang; Choi, Young-Jin

2012-01-01

The old calendar of pollens did not reflect current pollen distribution and concentrations that can be influenced by changes of weather and environment of each region in South Korea. A new pollen calendar of allergenic pollens was made based on the data on pollen concentrations obtained in eight regions nationwide between 1997 and 2009. The distribution of pollen was assessed every day at 8 areas (Seoul, Guri, Busan, Daegu, Jeonju, Kwangju, Kangneung, and Jeju) for 12 years between July 1, 1997 and June 30, 2009. Pollens were collected by using Burkard 7-day sampler (Burkard Manufacturing Co Ltd, UK). Pollens which were stained with Calberla's fuchsin staining solution were identified and counted. Pine became the highest pollen in May, and the pollen concentrations of oak and birch also became high. Ragweed appeared in the middle of August and showed the highest pollen concentration in the middles of September. Japanese hop showed a high concentration between the middle of August and the end of September, and mugwort appeared in the middles of August and its concentration increased up until early September. In Kangneung, birch appeared earlier, pine showed a higher pollen concentration than in the other areas. In Daegu, Oriental thuja and alder produced a large concentration of pollens. Pine produced a large concentration of pollens between the middle of April and the end of May. Weeds showed higher concentrations in September and mugwort appeared earlier than ragweed. In Busan the time of flowering is relatively early, and alder and Oriental thuja appeared earliest among all areas. In Kwangju, Oriental thuja and hazelnut appeared in early February. Japanese cedar showed the highest pollen concentration in March in Jeju. In conclusion, update information on pollen calendar in South Korea should be provided for allergic patients through the website to manage and prevent the pollinosis. PMID:22211164

Thermoluminescence (TL) properties and x-ray diffraction (XRD) analysis of high purity CaSO4:Dy TL material

NASA Astrophysics Data System (ADS)

Kamarudin, Nadira; Abdullah, Wan Saffiey Wan; Hamid, Muhammad Azmi Abdul; Dollah, Mohd Taufik

2014-09-01

This paper presents the characterization and TL properties of dysprosium (Dy) doped calcium sulfate (CaSO4) TL material produced by co-precipitation technique with 0.5mol% concentration of dopant. The morphology of the produced TL material was studied using scanning electron microscope (SEM) and the micrograph shows that rectangular parallelepiped shaped crystal with the average of 150 μm in length were produced. The crystallinity of the produced powder was studied using x-ray powder diffraction (XRD). The XRD spectra show that the TL material produced is high purity anhydrite CaSO4 with average crystallite size of 74 nm with orthorhombic crystal system. The TL behavior of produced CaSO4:Dy was studied using a TLD reader after exposure to gamma ray by Co60 source with the doses of 1,5 and 10 Gy. The glow curve shows linear response with glow peak around 230°C which is desired development in the field of radiation dosimetry.

Enhanced gelation of chitosan/β-sodium glycerophosphate thermosensitive hydrogel with sodium bicarbonate and biocompatibility evaluated.

PubMed

Deng, Aipeng; Kang, Xi; Zhang, Jing; Yang, Yang; Yang, Shulin

2017-09-01

The application of chitosan/β-sodium glycerophosphate (β-GP) thermosensitive hydrogel has been limited by the relatively slow gelation, weak mechanical resistance and poor cytocompatibility. In this study, sodium hydrogen carbonate (NaHCO 3 ) was applied with β-GP as gel agents to produce high-strength hydrogel. The hydrogels prepared with high NaHCO 3 concentration or more gel agents showed shorter gelation time, better thermostability, drastically enhanced resistance in compression. Meanwhile, the hydrogels presented obvious porous structures and excellent biocompatibility to HUVEC and NIH 3T3 cultured in vitro with higher NaHCO 3 concentration and moderate concentration of β-GP. Overall, appropriate concentration of β-GP combined with NaHCO 3 can be a good gel regent to improve properties of chitosan thermosensitive hydrogels. Copyright © 2017 Elsevier B.V. All rights reserved.

METHOD FOR PREPARING NORMORPHINE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rapoport, H.; Look, M.

1959-06-01

An improved method is presented for producing normorphine from morphine. Morphine as the starting material is acetylated by treatment with acetylating agents to produce di-acetyl morphine (heroin). The acetylated compound is reacted with cyanating agents to produce di-acetyl-cyanonormorphine (cyanonorheroin). The di-acetyl-cyanonormorphine compound is then treated in accordance with the improved hydrolysis reactions of the present invention in which concentrated hydrochloric acid is employed for a limited time period to hydrolyze the acetyl group therefrom forming cyanonormorphine. Subsequently, the reaction mixture is diluted and hydrolysis of the cyano groups from the cyanonormorphine is effected with a longer contact time with dilutemore » hydrochloric acid thereby producing normorphine. A high over-all conversion and production of a high purity product which may be radioactlvely labeled, if desired, is obtained by operation of the process.« less

Toxicity of harmful cyanobacterial blooms to bream and roach.

PubMed

Trinchet, Isabelle; Cadel-Six, Sabrina; Djediat, Chakib; Marie, Benjamin; Bernard, Cécile; Puiseux-Dao, Simone; Krys, Sophie; Edery, Marc

2013-09-01

Aquatic ecosystems are facing increasing environmental pressures, leading to an increasing frequency of cyanobacterial Harmful Algal Blooms (cHABs) that have emerged as a worldwide concern due to their growing frequency and their potential toxicity to the fauna that threatens the functioning of ecosystems. Cyanobacterial blooms raise concerns due to the fact that several strains produce potent bioactive or toxic secondary metabolites, such as the microcystins (MCs), which are hepatotoxic to vertebrates. These strains of cyanobacteria may be potentially toxic to fish via gastrointestinal ingestion and also by direct absorption of the toxin MC from the water. The purpose of our study was to investigate toxic effects observed in fish taken from several lakes in the Ile-de-France region, where MCs-producing blooms occur. This study comprises histological studies and the measurement of MC concentrations in various organs. The histological findings are similar to those obtained following laboratory exposure of medaka fish to MCs: hepatic lesions predominate and include cell lysis and cell detachment. MC concentrations in the organs revealed that accumulation was particularly high in the digestive tract and the liver, which are known to be classical targets of MCs. In contrast concentrations were very low in the muscles. Differences in the accumulation of MC variants produced by blooms indicate that in order to more precisely evaluate the toxic potential of a specific bloom it is necessary not only to consider the concentration of toxins, but also the variants produced. Copyright © 2013 Elsevier Ltd. All rights reserved.

A successful closed aquatic ecosystem in SZ-8 mission

NASA Astrophysics Data System (ADS)

Li, Xiaoyan; Wang, Gaohong; Richter, Peter; Liu, Yongding; Schuster, Martin; Lebert, Michael

2012-07-01

Aquatic ecosystem is a useful means to explore complex interaction among different species, and data got from this kind of system can be used to re-constructer or bio-remedy damaged ecosystem or explore other planet, such as Mars. To deeply investigate interactions of different species in space environment, we established a closed aquatic ecosystem of 60 milliliter with Chlorella, Euglena and Bulinus. As a major oxygen producer, Euglena was put into the lower chamber. The initial concentration of Euglena was adjusted to 40000 cells per milliliter to avoid damage of high oxygen concentration to other organisms. As a secondary oxygen producer and food provider, Chlorella was put into the upper chamber together with 3 bulinus. The initial concentration of Chlorella was 3.2*105 cells per milliliter. After 17.5 days of duration, the system run well with 1 bulinus alive in the spaceflight group and all kept alive in the ground control.

Simultaneous presence of O3 and CO bands in the troposphere

NASA Technical Reports Server (NTRS)

Fishman, J.; Seiler, W.; Haagenson, P.

1980-01-01

Vertical profiles of CO and O3 in the troposphere and lower stratosphere have been constructed during a series of flights conducted in July and August 1974 over the American continents between 53 deg S and 67 deg N. The mixing ratios of both gases show large fluctuations with altitude in the Northern Hemisphere. Most of the observed bands of O3 in the free troposphere are coexistent with elevated CO concentrations indicating that this O3 is probably not of stratospheric origin, but most likely produced in the troposphere. From the observations, it is not clear whether these high concentrations of ozone were produced in situ in the remote troposphere or had been transported out of a polluted boundary layer. Isentropic trajectory calculations likewise indicate that the air containing these elevated ozone and carbon monoxide concentrations had been situated in the troposphere for at least 72 h prior to being sampled.

Dose related in vitro effects of ranitidine and cimetidine on basal and ACTH-stimulated steroidogenesis.

PubMed Central

Kenyon, C J; Fraser, R; Birnie, G G; Connell, J M; Lever, A F

1986-01-01

Isolated bovine adrenocortical cells were incubated with and without 3 ng/ml ACTH, with various concentrations (10-1000 micrograms/ml) of either cimetidine or ranitidine. Cortisol, corticosterone, and deoxycorticosterone outputs were measured. Cimetidine and ranitidine at 320 and 1000 micrograms/ml inhibited ACTH-stimulated corticosterone and cortisol synthesis and cimetidine decreased basal cortisol synthesis. The inhibitory effects of cimetidine on cortisol synthesis were approximately 10 times greater than those of ranitidine. Cimetidine (1000 micrograms/ml), but not ranitidine increased deoxycorticosterone synthesis by ACTH-stimulated cells, indicating inhibition of 11 beta-hydroxylation in the adrenal steroidogenic pathway. Although doses of cimetidine and ranitidine which produce these in vitro effects are much greater than plasma concentrations in normal clinical use, they might be important in acutely ill patients given intravenous bolus injections of cimetidine, or if either antagonist were accumulated by the adrenal to produce high intracellular concentrations. PMID:3023203

Efficient Production of Lactic Acid from Sweet Sorghum Juice by a Newly Isolated Lactobacillus salivarius CGMCC 7.75.

PubMed

Liu, Quanlan; Wang, Shanglong; Zhi, Jian-Fei; Ming, Henglei; Teng, Dawei

2013-09-01

Sweet sorghum juice was a cheap and renewable resource, and also a potential carbon source for the fermentation production of lactic acid (LA) by a lactic acid bacterium. One newly isolated strain Lactobacillus salivarius CGMCC 7.75 showed the ability to produce the highest yield and optical purity of LA from sweet sorghum juice. Studies of feeding different concentrations of sweet sorghum juice and nitrogen source suggested the optimal concentrations of fermentation were 325 ml l(-1) and 20 g l(-1), respectively. This combination produced 142.49 g l(-1) LA with a productivity level of 0.90 g of LA per gram of sugars consumed. The results indicated the high LA concentration achieved using L. salivarius CGMCC 7.75 not only gives cheap industrial product, but also broaden the application of sweet sorghum.

Overview of selected surrogate technologies for high-temporal resolution suspended-sediment monitoring

USGS Publications Warehouse

Gray, John R.; Gartner, Jeffrey W.

2010-01-01

Traditional methods for characterizing selected properties of suspended sediments in rivers are being augmented and in some cases replaced by cost-effective surrogate instruments and methods that produce a temporally dense time series of quantifiably accurate data for use primarily in sediment-flux computations. Turbidity is the most common such surrogate technology, and the first to be sanctioned by the U.S. Geological Survey for use in producing data used in concert with water-discharge data to compute sediment concentrations and fluxes for storage in the National Water Information System. Other technologies, including laser-diffraction, digital photo-optic, acoustic-attenuation and backscatter, and pressure-difference techniques are being evaluated for producing reliable sediment concentration and, in some cases, particle-size distribution data. Each technology addresses a niche for sediment monitoring. Their performances range from compelling to disappointing. Some of these technologies have the potential to revolutionize fluvial-sediment data collection, analysis, and availability.

Ion and laser microprobes applied to the measurement of corrosion produced hydrogen on a microscopic scale.

NASA Technical Reports Server (NTRS)

Gray, H. R.

1972-01-01

Use of an ion microprobe and a laser microprobe to measure concentrations of corrosion-produced hydrogen on a microscopic scale. Hydrogen concentrations of several thousand ppm were measured by both analytical techniques below corroded and fracture surfaces of hot salt stress corroded titanium alloy specimens. This extremely high concentration compares with only about 100 ppm hydrogen determined by standard vacuum fusion chemical analyses of bulk samples. Both the ion and laser microprobes were used to measure hydrogen concentration profiles in stepped intervals to substantial depths below the original corroded and fracture surfaces. For the ion microprobe, the area of local analysis was 22 microns in diameter and for the laser microprobe, the area of local analysis was about 300 microns in diameter. The segregation of hydrogen below fracture surfaces supports a previously proposed theory that corrosion-produced hydrogen is responsible for hot salt stress corrosion embrittlement and cracking of titanium alloys. These advanced analytical techniques suggest great potential for many areas of stress corrosion and hydrogen embrittlement research, quality control, and field inspection of corrosion problems. For example, it appears possible that a contour map of hydrogen distribution at notch roots and crack tips could be quantitatively determined. Such information would be useful in substantiating current theories of stress corrosion and hydrogen embrittlement.

Anaerobic digestion of post-hydrothermal liquefaction wastewater for improved energy efficiency of hydrothermal bioenergy processes.

PubMed

Zhou, Yan; Schideman, Lance; Zheng, Mingxia; Martin-Ryals, Ana; Li, Peng; Tommaso, Giovana; Zhang, Yuanhui

2015-01-01

Hydrothermal liquefaction (HTL) is a promising process for converting wet biomass and organic wastes into bio-crude oil. It also produces an aqueous product referred to as post-hydrothermal liquefaction wastewater (PHWW) containing up to 40% of the original feedstock carbon, which reduces the overall energy efficiency of the HTL process. This study investigated the feasibility of using anaerobic digestion (AD) to treat PHWW, with the aid of activated carbon. Results showed that successful AD occurred at relatively low concentrations of PHWW (≤ 6.7%), producing a biogas yield of 0.5 ml/mg CODremoved, and ∼53% energy recovery efficiency. Higher concentrations of PHWW (≥13.3%) had an inhibitory effect on the AD process, as indicated by delayed, slower, or no biogas production. Activated carbon was shown to effectively mitigate this inhibitory effect by enhancing biogas production and allowing digestion to proceed at higher PHWW concentrations (up to 33.3%), likely due to sequestering toxic organic compounds. The addition of activated carbon also increased the net energy recovery efficiency of AD with a relatively high concentration of PHWW (33.3%), taking into account the energy for producing activated carbon. These results suggest that AD is a feasible approach to treat PHWW, and to improve the energy efficiency of the HTL processes.

Analytical and toxicological evaluation of flavor chemicals in electronic cigarette refill fluids.

PubMed

Behar, Rachel Z; Luo, Wentai; McWhirter, Kevin J; Pankow, James F; Talbot, Prue

2018-05-29

Thousands of electronic cigarette refill fluids are commercially available. The concentrations of nicotine and the solvents, but not the flavor chemicals, are often disclosed on product labels. The purpose of this study was to identify and quantify flavor chemicals in 39 commercial refill fluids that were previously evaluated for toxicity. Twelve flavor chemicals were identified with concentrations ≥1 mg/ml: cinnamaldehyde, menthol, benzyl alcohol, vanillin, eugenol, p-anisaldehyde, ethyl cinnamate, maltol, ethyl maltol, triacetin, benzaldehyde, and menthone. Transfer of these flavor chemicals into aerosols made at 3V and 5V was efficient (mean transfer = 98%). We produced lab-made refill fluids containing authentic standards of each flavor chemical and analyzed the toxicity of their aerosols produced at 3V and 5V using a tank Box Mod device. Over 50% of the refill fluids in our sample contained high concentrations of flavor chemicals that transferred efficiently to aerosols at concentrations that produce cytotoxicity. When tested with two types of human lung cells, the aerosols made at 5V were generally more toxic than those made at 3V. These data will be valuable for consumers, physicians, public health officials, and regulatory agencies when discussing potential health concerns relating to flavor chemicals in electronic cigarette products.

Total lead concentration in new decorative enamel paints in Lebanon, Paraguay and Russia.

PubMed

Clark, C Scott; Speranskaya, Olga; Brosche, Sara; Gonzalez, Hebe; Solis, Daniela; Kodeih, Naji; Roda, Sandy; Lind, Caroline

2015-04-01

Lead concentrations in new enamel decorative paints were determined in three countries in different areas of the world where data were not previously available. The average total lead concentration of the enamel decorative paints purchased in Lebanon, Paraguay and Russia was 24,500ppm (ppm, dry weight), more than 270 times the current limit of 90ppm in Canada and in the United States. Sixty-three percent of these paints contained concentrations greater than 90ppm. Fifty-nine percent contained concentrations greater than 600ppm, the current limit in some countries. The maximum concentrations found were 236,000ppm in Lebanon, 169,000ppm in Paraguay and 52,900ppm in Russia. An average of 29% of the samples contained exceedingly high lead concentrations, >=10,000ppm. Five brands of paint were sampled in each of Lebanon and Paraguay and seven in Russia. Three colors from each brand were analyzed. For five of the six samples of the two brands in Lebanon with affiliations outside the country, the lead concentrations ranged from 1360ppm to 135,000ppm. In Lebanon the maximum concentration in the Egypt-affiliated brand (Sipes) was 135,000ppm and the maximum for the USA-affiliated brand (Dutch Boy) was 32,400ppm. Lead was not detected in any paints from the three of the four brands of paint purchased in Paraguay that had headquarters/affiliations in other countries (Brazil-Coralit), Germany (Suvinil) and USA (Novacor)). Two of the three paints from each of the other Paraguay brands contained high levels of lead with the maximum concentrations of 108,000 and 168,000ppm; one of these brands was manufactured under a license from ICI in the Netherlands. All of the paints purchased in Russia were from Russian brands and were manufactured in Russia. All three paints from one brand contained below detection levels of lead. The maximum levels of lead in the other six brands in Russia ranged from 3230 to 52,900ppm. The two brands with the highest lead concentration, TEKS and LAKRA, were produced by companies in the top three in market share.. Overall, lead concentrations were much higher in the colored paints such as red and yellow than in white paints. In each of the three countries a brand based in that country had a colored paint that either met a 90ppm limit or was close to meeting the limit-demonstrating that practical technology was available in each of these countries to produce low lead bright colored enamel decorative paints. Even though technology for producing paint without added lead existed in each of these countries, twenty-nine (29) percent of the paints analyzed contained exceedingly high concentrations (>=10,000ppm) of lead. Copyright © 2015 Elsevier Inc. All rights reserved.

Statistical Analysis Of Heavy Metals Concentration In Watermelon Plants Irrigated By Wastewater

NASA Astrophysics Data System (ADS)

Khanjani, M. J.; Maghsoudi moud, A. A.; Saffari, V. R.; Hashamipor, S. M.; Soltanizadeh, M.

2008-01-01

Concentration of heavy metals in vegetables irrigated by urban wastewater is a cause of serious concern due to the potentials health problems of consuming contaminated produce. In this study it is tried to model the concentration of heavy metals (Cd, Cr, Cu, Fe,…) as a function of their concentration in watermelon roots and stems. Our study shows there is a good relationship between them for most of collected data. By measuring the concentration in root and stem of watermelon plant samples before harvesting, the concentration of heavy metal in watermelon's fruit can be estimated by presented mathematical models. This study shows the concentrations of heavy metals in fruits, roots and stems of watermelon plants are very high and in dangerous level when irrigated by municipal waste water.

High hydrostatic pressure modification of whey protein concentrate for improved body and texture of lowfat ice cream.

PubMed

Lim, S-Y; Swanson, B G; Ross, C F; Clark, S

2008-04-01

Previous research demonstrated that application of high hydrostatic pressure (HHP), particularly at 300 MPa for 15 min, can enhance foaming properties of whey protein concentrate (WPC). The purpose of this research was to determine the practical impact of HHP-treated WPC on the body and texture of lowfat ice cream. Washington State University (WSU)-WPC was produced by ultrafiltration of fresh separated whey received from the WSU creamery. Commercial whey protein concentrate 35 (WPC 35) powder was reconstituted to equivalent total solids as WSU-WPC (8.23%). Three batches of lowfat ice cream mix were produced to contain WSU-WPC without HHP, WSU-WPC with HHP (300 MPa for 15 min), and WPC 35 without HHP. All lowfat ice cream mixes contained 10% WSU-WPC or WPC 35. Overrun and foam stability of ice cream mixes were determined after whipping for 15 min. Ice creams were produced using standard ice cream ingredients and processing. The hardness of ice creams was determined with a TA-XT2 texture analyzer. Sensory evaluation by balanced reference duo-trio test was carried out using 52 volunteers. The ice cream mix containing HHP-treated WSU-WPC exhibited the greatest overrun and foam stability, confirming the effect of HHP on foaming properties of whey proteins in a complex system. Ice cream containing HHP-treated WSU-WPC exhibited significantly greater hardness than ice cream produced with untreated WSU-WPC or WPC 35. Panelists were able to distinguish between ice cream containing HHP-treated WSU-WPC and ice cream containing untreated WPC 35. Improvements of overrun and foam stability were observed when HHP-treated whey protein was used at a concentration as low as 10% (wt/wt) in ice cream mix. The impact of HHP on the functional properties of whey proteins was more pronounced than the impact on sensory properties.

Deposition and processing of airborne nitrogen pollutants in mediterranean-type ecosystems of southern California

Treesearch

Philip J. Riggan; Robert N. Lockwood; Ernest N. Lopez

1985-01-01

Atmospheric nitrogen deposition, associated with chronic urban air pollution, has produced stream water nitrate concentrations as high as 7.0 mg of N L-l in chaparral watersheds in the San Gabriel Mountains of Los Angeles County, CA. Stream water [NO3-] and discharge were greatest at high flow and may...

The Impact of Aerosols on Cloud and Precipitation Processes: Cloud-Resolving Model Simulations

NASA Technical Reports Server (NTRS)

Tao, Wei-Kuo; Khain, A.; Simpson, S.; Johnson, D.; Li, X.; Remer, L.

2003-01-01

Cloud microphysics are inevitable affected by the smoke particle (CCN, cloud condensation nuclei) size distributions below the clouds. Therefore, size distribution parameterized as spectral bin microphysics are needed to explicitly study the effect of atmospheric aerosol concentration on cloud development, rainfall production, and rainfall rates convective clouds. Recently, two detailed spectral-bin microphysical schemes were implemented into the Goddard Cumulus Ensembel (GCE) model. The formulation for the explicit spectral-bim microphysical processes is based on solving stochastic kinetic equations for the size distribution functions of water droplets (i.e., cloud droplets and raindrops), and several types of ice particles [i.e., pristine ice crystals (columnar and plate-like), snow (dendrites and aggregates), groupel and frozen drops/hall] Each type is described by a special size distribution function containing many categories (i.e., 33 bins). Atmospheric aerosols are also described using number density size-distribution functions.A spectral-bin microphysical model is very expensive from a computational point of view and has only been implemented into the 2D version of the GCE at the present time. The model is tested by studying the evolution of deep cloud systems in the west Pacific warm pool region and in the mid-latitude using identical thermodynamic conditions but with different concentrations of CCN: a low "clean" concentration and a high "dirty" concentration. Besides the initial differences in aerosol concentration, preliminary results indicate that the low CCN concentration case produces rainfall at the surface sooner than the high CCN case but has less cloud water mass aloft. Because the spectral-bim model explicitly calculates and allows for the examination of both the mass and number concentration of cpecies in each size category, a detailed analysis of the instantaneous size spectrum can be obtained for the two cases. It is shown that since the low CCN case produces fever droplets, larger size develop due to greater condencational and collectional growth, leading to a broader size spectrum in comparison to the high CCN case.

The Impact of Aerosols on Cloud and Precipitation Processes: Cloud-Resolving Model Simulations

NASA Technical Reports Server (NTRS)

Tao, Wei-Kuo; Khain, A.; Simpson, S.; Johnson, D.; Li, X.; Remer, L.

2003-01-01

Cloud microphysics are inevitably affected by the smoke particle (CCN, cloud condensation nuclei) size distributions below the clouds. Therefore, size distributions parameterized as spectral bin microphysics are needed to explicitly study the effects of atmospheric aerosol concentration on cloud development, rainfall production, and rainfall rates for convective clouds. Recently, two detailed spectral-bin microphysical schemes were implemented into the Goddard Cumulus Ensemble (GCE) model. The formulation for the explicit spectral-bin microphysical processes is based on solving stochastic kinetic equations for the size distribution functions of water droplets (i.e., cloud droplets and raindrops), and several types of ice particles [i.e.,pristine ice crystals (columnar and plate-like), snow (dendrites and aggregates), graupel and frozen drops/hail]. Each type is described by a special size distribution function containing many categories (i.e. 33 bins). Atmospheric aerosols are also described using number density size-distribution functions.A spectral-bin microphysical model is very expensive from a from a computational point of view and has only been implemented into the 2D version of the GCE at the present time. The model is tested by studying the evolution of deep tropical clouds in the west Pacific warm pool region using identical thermodynamic conditions but with different concentrations of CCN: a low "clean" concentration and a high "dirty" concentration. Besides the initial differences in aerosol concentration, preliminary results indicate that the low CCN concentration case produces rainfall at the surface sooner than the high CCN case but has less cloud water mass aloft. Because the spectral-bin model explicitly calculates and allows for the examination of both the mass and number concentration of species in each size categor, a detailed analysis of the instantaneous size spectrum can be obtained for the two cases. It is shown that since the low CCN case produces fewer droplets, larger sized develop due to the greater condensational and collectional growth, leading to a broader size spectrum in comparison to the high CCN case.

Method of producing .sup.67 Cu

DOEpatents

O'Brien, Jr., Harold A.; Barnes, John W.; Taylor, Wayne A.; Thomas, Kenneth E.; Bentley, Glenn E.

1984-01-01

A method of producing carrier-free .sup.67 Cu by proton spallation combined with subsequent chemical separation and purification is disclosed. A target consisting essentially of pressed zinc oxide is irradiated with a high energy, high current proton beam to produce a variety of spallogenic nuclides, including .sup.67 Cu and other copper isotopes. The irradiated target is dissolved in a concentrated acid solution to which a palladium salt is added. In accordance with the preferred method, the spallogenic copper is twice coprecipitated with palladium, once with metallic zinc as the precipitating agent and once with hydrogen sulfide as the precipitating agent. The palladium/copper precipitate is then dissolved in an acid solution and the copper is separated from the palladium by liquid chromatography on an anion exchange resin.

Method for producing /sup 67/Cu

DOEpatents

O'Brien, H.A. Jr.; Barnes, J.W.; Taylor, W.A.; Thomas, K.E.; Bentley, G.E.

A method of producing carrier-free /sup 67/Cu by proton spallation combined with subsequent chemical separation and purification is disclosed. A target consisting essentially of pressed zinc oxide is irradiated with a high energy, high current proton beam to produce a variety of spallogenic nuclides, including /sup 67/Cu and other copper isotopes. The irradiated target is dissolved in a concentrated acid solution to which a palladium salt is added. In accordance with the preferred method, the spallogenic copper is twice coprecipitated with palladium, once with metallic zinc as the precipitating agent and once with hydrogen sulfide as the precipitating agent. The palladium/copper precipitate is then dissolved in an acid solution and the copper is separated from the palladium by liquid chromatography on an anion exchange resin.

An experimental phantom study of the effect of gadolinium-based MR contrast agents on PET attenuation coefficients and PET quantification in PET-MR imaging: application to cardiac studies.

PubMed

O' Doherty, Jim; Schleyer, Paul

2017-12-01

Simultaneous cardiac perfusion studies are an increasing trend in PET-MR imaging. During dynamic PET imaging, the introduction of gadolinium-based MR contrast agents (GBCA) at high concentrations during a dual injection of GBCA and PET radiotracer may cause increased attenuation effects of the PET signal, and thus errors in quantification of PET images. We thus aimed to calculate the change in linear attenuation coefficient (LAC) of a mixture of PET radiotracer and increasing concentrations of GBCA in solution and furthermore, to investigate if this change in LAC produced a measurable effect on the image-based PET activity concentration when attenuation corrected by three different AC strategies. We performed simultaneous PET-MR imaging of a phantom in a static scenario using a fixed activity of 40 MBq [18 F]-NaF, water, and an increasing GBCA concentration from 0 to 66 mM (based on an assumed maximum possible concentration of GBCA in the left ventricle in a clinical study). This simulated a range of clinical concentrations of GBCA. We investigated two methods to calculate the LAC of the solution mixture at 511 keV: (1) a mathematical mixture rule and (2) CT imaging of each concentration step and subsequent conversion to LAC at 511 keV. This comparison showed that the ranges of LAC produced by both methods are equivalent with an increase in LAC of the mixed solution of approximately 2% over the range of 0-66 mM. We then employed three different attenuation correction methods to the PET data: (1) each PET scan at a specific millimolar concentration of GBCA corrected by its corresponding CT scan, (2) each PET scan corrected by a CT scan with no GBCA present (i.e., at 0 mM GBCA), and (3) a manually generated attenuation map, whereby all CT voxels in the phantom at 0 mM were replaced by LAC = 0.1 cm -1 . All attenuation correction methods (1-3) were accurate to the true measured activity concentration within 5%, and there were no trends in image-based activity concentrations upon increasing the GBCA concentration of the solution. The presence of high GBCA concentration (representing a worst-case scenario in dynamic cardiac studies) in solution with PET radiotracer produces a minimal effect on attenuation-corrected PET quantification.

Process to Produce Iron Nanoparticle Lunar Dust Simulant Composite

NASA Technical Reports Server (NTRS)

Hung, Ching-cheh; McNatt, Jeremiah

2010-01-01

A document discusses a method for producing nanophase iron lunar dust composite simulant by heating a mixture of carbon black and current lunar simulant types (mixed oxide including iron oxide) at a high temperature to reduce ionic iron into elemental iron. The product is a chemically modified lunar simulant that can be attracted by a magnet, and has a surface layer with an iron concentration that is increased during the reaction. The iron was found to be -iron and Fe3O4 nanoparticles. The simulant produced with this method contains iron nanoparticles not available previously, and they are stable in ambient air. These nanoparticles can be mass-produced simply.

The effect of natural zeolite as microbial immobilization media in anaerobic digestion at various concentrations of palm oil mill effluent (POME)

NASA Astrophysics Data System (ADS)

Ayu, Erika Dyah; Halim, Lenny; Mellyanawaty, Melly; Sudibyo, Hanifrahmawan; Budhijanto, Wiratni

2017-05-01

Anaerobic digestion is one of the solutions in POME treatment because it generates energy in the form of biogas. Nevertheless, high concentration of POME fed into the digester will cause high acidification level and eventually cause process failure. The failure can also be affected by high inhibitor concentration contained in POME, one of which is long chain fatty acid. The addition of immobilization media is commonly used to increase the bacteria resistance to inhibitor. Natural zeolite is considered as appropriate immobilization media for waste treatment purpose since it is cheap, has high mechanical strength, high immobilization capacity, and its ability as cation exchanger. The digested biodiesel waste was used as starter inoculum for its good capability in digesting oil-containing feed such as POME. This research was conducted to evaluate critical concentration of POME fed to digester where the natural zeolite could not reduce the inhibitory effect. The concentrations of POME evaluated were 10,000 mg sCOD/L and 17,000 mg sCOD/L, which were higher than previous studies(5,000 to 8,000 mg sCOD/L). The research showed that at such high sCOD concentrations, the addition of zeolite did not significantly increase COD reduction nor biogas production rate, for both POME concentrations to be compared to control. The biogas produced by digester fed by 10,000 mg/L POME and 17,000 mg/L POME was 751 and 100 mL/g sCOD, respectively, indicating higher inhibitor effect in the digester with 17,000 mg SCOD/L initial concentration.

Lactobacillus farciminis MD, a newer strain with potential for bacteriocin and antibiotic assay.

PubMed

Halami, P M; Chandrashekar, A; Nand, K

2000-03-01

A native isolate Lactobacillus farciminis MD isolated from fermenting mushroom exhibited a high degree of sensitivity to the majority of the bacteriocins produced by strains of lactobacilli, leuconostoc and pediococci. Also, the efficacy of Lact. farciminis MD as a sensitive strain for antibiotic assay was established against different antibiotics including ampicillin, cefazoline, chloramphenicol and nitrofurantoin at concentrations of 30 microg each, showing an inhibition zone of 30 mm diameter. The high degree of sensitivity towards bacteriocins and antibiotics provide potential for the exploitation of Lact. farciminis MD in establishing very well-defined bacteriocin producers.

High Throughput Pharmacokinetics for Environmental Chemicals (FutureToxII)

EPA Science Inventory

Pharmacokinetic (PK) models are critical to determine whether chemical exposures produce potentially hazardous tissue concentrations. For bioactivity identified in vitro (e.g. ToxCast) – hazardous or not – PK models can forecast exposure thresholds, below which no significant bio...

Process for producing nickel electrode having lightweight substrate

NASA Technical Reports Server (NTRS)

Lim, Hong S. (Inventor)

1996-01-01

A nickel electrode having a lightweight porous nickel substrate is subjected to a formation cycle involving heavy overcharging and under-discharging in a KOH electrolyte having a concentration of 26% to 31%, resulting in electrodes displaying high active material utilization.

High-spatial-resolution nanoparticle x-ray fluorescence tomography

NASA Astrophysics Data System (ADS)

Larsson, Jakob C.; Vâgberg, William; Vogt, Carmen; Lundström, Ulf; Larsson, Daniel H.; Hertz, Hans M.

2016-03-01

X-ray fluorescence tomography (XFCT) has potential for high-resolution 3D molecular x-ray bio-imaging. In this technique the fluorescence signal from targeted nanoparticles (NPs) is measured, providing information about the spatial distribution and concentration of the NPs inside the object. However, present laboratory XFCT systems typically have limited spatial resolution (>1 mm) and suffer from long scan times and high radiation dose even at high NP concentrations, mainly due to low efficiency and poor signal-to-noise ratio. We have developed a laboratory XFCT system with high spatial resolution (sub-100 μm), low NP concentration and vastly decreased scan times and dose, opening up the possibilities for in-vivo small-animal imaging research. The system consists of a high-brightness liquid-metal-jet microfocus x-ray source, x-ray focusing optics and an energy-resolving photon-counting detector. By using the source's characteristic 24 keV line-emission together with carefully matched molybdenum nanoparticles the Compton background is greatly reduced, increasing the SNR. Each measurement provides information about the spatial distribution and concentration of the Mo nanoparticles. A filtered back-projection method is used to produce the final XFCT image.

An Alternative to NOx Cap-and-Trade Programs: An Exploratory Analysis of Charging NOx Emitters for Health Damages

NASA Astrophysics Data System (ADS)

Mauzerall, D. L.; Sultan, B.; Kim, N.; Bradford, D.

2003-12-01

To address the problem of elevated O3 concentrations throughout the northeastern United States in summer, a NOx cap-and-trade program was implemented that reduced NOx emissions from large point sources by nearly 50%. To determine whether this program has been successful, we examine O3, NO and temperature measurements collected in the EPA-AIRS network prior to and after the cap-and-trade program went into effect in 1999. Ambient NO concentrations as measured in the EPA-AIRS network are lower in the post-cap period in all months except July. We find that the upper half of the distribution of O3 concentrations within the region is essentially unchanged (or slightly higher) in May and June, modestly reduced in July and August (except the highest concentrations which are larger in August), and significantly lower in September (ranging from 0-20 ppb lower between the mean and highest concentrations) in the 1999-2001 post-cap period relative to the 1995-1998 pre-cap period. Except for September, the frequency with which the 80ppb 8-hour NAAQS standard for O3 is exceeded has not decreased. Temperatures during the post-cap period were slightly higher in June, July and August, and slightly lower in September - likely contributing to reduced O3 levels during September in the post-cap period. To explore the possibility that trading, or selective emissions over the course of the summer, could influence regional O3 concentrations, we conduct chemical transport modeling experiments using the CAMx regional model. Even within May-September for a single year, demands for electrical power and hence NOx emissions are greater during hot than cool periods. We demonstrate that substantially more O3 is produced from identical NOx emissions from a single power plant on high temperature than on low temperature days in July 1995. Thus a lack of temporal restrictions on when in a single summer month NOx emissions may occur can result in higher O3 levels. We also demonstrate that identical NOx emissions in regions of high (low) isoprene emission result in greater (lesser) O3 production. This indicates that NOx trades from locations with low to high isoprene emissions likely result in increases in O3 production. Since the objective of reducing O3 concentrations is to reduce the impact elevated O3 has on human health and welfare, we examine the mortalities that result from the O3 produced from a fixed NOx emission in the two cases described above as well as in regions of high and low population. We estimate substantially higher mortality rates from a unit NOx emission as a result of elevated O3 concentrations for high temperature days, in regions of high isoprene emissions, and for emissions occurring upwind of large populations. We attempt to assign a monetary value to the loss of life resulting from the enhanced O3 concentrations that result from these NOx emissions. We propose, as an alternative to NOx emissions cap and trade programs, a system by which NOx emitters are charged for the marginal damage they cause as a result of the O3 produced from the NOx they emit. Rather than resulting in a reduction in total NOx emissions without necessarily reducing O3 concentrations (as a cap-and-trade program does), this alternative system provides a direct incentive to reduce NOx emissions at times and places where they cause the most harm.

Environmental implications of high metal content in soils of a titanium mining zone in Kenya.

PubMed

Maina, David M; Ndirangu, Douglas M; Mangala, Michael M; Boman, Johan; Shepherd, Keith; Gatari, Michael J

2016-11-01

Mining activities contribute to an increase of specific metal contaminants in soils. This may adversely affect plant life and consequently impact on animal and human health. The objective of this study was to obtain the background metal concentrations in soils around the titanium mining in Kwale County for monitoring its environmental impacts. Forty samples were obtained with half from topsoils and the other from subsoils. X-ray fluorescence spectrometry was used to determine the metal content of the soil samples. High concentrations of Ti, Mn, Fe, and Zr were observed where Ti concentrations ranged from 0.47 to 2.8 %; Mn 0.02 to 3.1 %; Fe 0.89 to 3.1 %; and Zr 0.05 to 0.85 %. Using ratios of elemental concentrations in topsoil to subsoil method and enrichment factors concept, the metals were observed to be of geogenic origin with no anthropogenic input. The high concentrations of Mn and Fe may increase their concentration levels in the surrounding agricultural lands through deposition, thereby causing contamination on the land and the cultivated food crops. The latter can cause adverse human health effects. In addition, titanium mining will produce tailings containing low-level titanium concentrations, which will require proper disposal to avoid increasing titanium concentrations in the soils of the region since it has been observed to be phytotoxic to plants at high concentrations. The results of this study will serve as reference while monitoring the environmental impact by the titanium mining activities.

Phenolic compounds, organic acids and antioxidant activity of grape juices produced in industrial scale by different processes of maceration.

PubMed

Lima, Marcos dos Santos; da Conceição Prudêncio Dutra, Maria; Toaldo, Isabela Maia; Corrêa, Luiz Claudio; Pereira, Giuliano Elias; de Oliveira, Débora; Bordignon-Luiz, Marilde Terezinha; Ninow, Jorge Luiz

2015-12-01

The effect of maceration process on the profile of phenolic compounds, organic acids composition and antioxidant activity of grape juices from new varieties of Vitis labrusca L. obtained in industrial scale was investigated. The extraction process presented a high yield without pressing the grapes. The use of a commercial pectinase resulted in an increase on extraction yield and procyanidins B1 and B2 concentrations and a decrease on turbidity and concentration of catechins. The combination of 60 °C and 3.0 mL 100 kg(-1) of enzyme resulted in the highest extraction of phenolic compounds, reducing the content of acetic acid. The juices presented high antioxidant activity, related to the great concentration of malvidin, cyanidin, catechin and caffeic, cinnamic and gallic acids. Among the bioactive compounds, the juices presented high concentration of procyanidin B1, caffeic acid and trans-resveratrol, with higher levels compared to those reported in the literature. Copyright © 2015 Elsevier Ltd. All rights reserved.

Borreliacidal OspC Antibody Response of Canines with Lyme Disease Differs Significantly from That of Humans with Lyme Disease▿

PubMed Central

Lovrich, Steven D.; La Fleur, Rhonda L.; Jobe, Dean A.; Johnson, Jennifer C.; Asp, Krista E.; Schell, Ronald F.; Callister, Steven M.

2007-01-01

Humans reliably produce high concentrations of borreliacidal OspC antibodies specific for the seven C-terminal amino acids shortly after infection with Borrelia burgdorferi. We show that dogs also produce OspC borreliacidal antibodies but that their frequencies, intensities, and antigenicities differ significantly. The findings therefore confirm a major difference between the borreliacidal antibody responses of humans and canines with Lyme disease. PMID:17344346

High Power Klystrons for Efficient Reliable High Power Amplifiers.

DTIC Science & Technology

1980-11-01

techniques to obtain high overall efficiency. One is second harmonic space charge bunching. This is a process whereby the fundamental and second harmonic...components of the space charge waves in the electron beam of a microwave tube are combined to produce more highly concentrated electron bunches raising the...the drift lengths to enhance the 2nd harmonic component in the space charge waves. The latter method was utilized in the VKC-7790. Computer

How to avoid glucose degradation products in peritoneal dialysis fluids.

PubMed

Erixon, Martin; Wieslander, Anders; Lindén, Torbjörn; Carlsson, Ola; Forsbäck, Gunita; Svensson, Eva; Jönsson, Jan Ake; Kjellstrand, Per

2006-01-01

The formation of glucose degradation products (GDPs) during sterilization of peritoneal dialysis fluids (PDFs) is one of the most important aspects of biocompatibility of glucose-containing PDFs. Producers of PDFs are thus trying to minimize the level of GDPs in their products. 3,4-Dideoxyglucosone-3-ene (3,4-DGE) has been identified as the most bioreactive GDP in PDFs. It exists in a temperature-dependent equilibrium with a pool of 3-deoxyglucosone (3-DG) and is a precursor in the irreversible formation of 5-hydroxymethyl furaldehyde (5-HMF). The aim of the present study was to investigate how to minimize GDPs in PDFs and how different manufacturers have succeeded in doing so. Glucose solutions at different pHs and concentrations were heat sterilized and 3-DG, 3,4-DGE, 5-HMF, formaldehyde, and acetaldehyde were analyzed. Conventional as well as biocompatible fluids from different manufacturers were analyzed in parallel for GDP concentrations. The concentrations of 3-DG and 3,4-DGE produced during heat sterilization decreased when pH was reduced to about 2. Concentration of 5-HMF decreased when pH was reduced to 2.6. After further decrease to a pH of 2.0, concentration of 5-HMF increased slightly, and below a pH of 2.0 it increased considerably, together with formaldehyde; 3-DG continued to drop and 3,4-DGE remained constant. Inhibition of cell growth was paralleled by 3,4-DGE concentration at pH 2.0 - 6.0. A high glucose concentration lowered concentrations of 3,4-DGE and 3-DG at pH 5.5 and of 5-HMF at pH 1. At pH 2.2 and 3.2, glucose concentration had a minor effect on the formation of GDPs. All conventional PDFs contained high levels of 3,4-DGE and 3-DG. Concentrations were considerably lower in the biocompatible fluids. However, the concentration of 5-H M F was slightly higher in all the biocompatible fluids. The best way to avoid reactive GDPs is to have a pH between 2.0 and 2.6 during sterilization. If pHs outside this range are used, it becomes more important to have high glucose concentration during the sterilization process. There are large variations in GDPs, both within and between biocompatible and conventionally manufactured PDFs.

Efficient transformation of sucrose into high pullulan concentrations by Aureobasidium melanogenum TN1-2 isolated from a natural honey.

PubMed

Jiang, Hong; Xue, Si-Jia; Li, Yan-Feng; Liu, Guang-Lei; Chi, Zhen-Ming; Hu, Zhong; Chi, Zhe

2018-08-15

A very high pullulan producing yeast-like fungus, Aureobasidium melanogenum TN1-2 isolated from a natural honey was found to be able to produce 97.0 g/L of pullulan from 140.0 g/L sucrose at a flask level while it could yield 114.0 g/L of pullulan within 134 h during a 10-liter fermentation, the yield was 0.81 g/g and the productivity was 0.86 g/L/h. The high ability to biosynthesize pullulan by this yeast-like fungal strain TN1-2 was related to high glucosyltransferase activity, high phosphofructo-2-kinase activity, high content of its cellular glycerol and low glucose repressor. The Mw of the produced pullulan was 1.42 × 10 5  g/mol. The low Mw may be due to the high α-amylase, glucoamylase and isopullulanase activities. The intracellular level of trehalose had no influence on high pullulan production by the yeast-like fungal strain TN1-2. Copyright © 2018. Published by Elsevier Ltd.

Production of Spirulina sp by utilization of wastewater from the powder type energy drinks

NASA Astrophysics Data System (ADS)

Sumantri, Indro; Priyambada, Ika Bagus

2015-12-01

Wastewater of energy drink type of powder produced when the the production equipment required cleaning treatment to produce one taste to others. These equipments washed by water, so that, it produced wastewater. It contains high organic substances and classified as high degradable due to food product. The content of wastewater is high carbon and nitrogen substances. Microalgae is an autotrophic microorganism, live without carbon presence, utilized to digest the substances in wastewater especially for nitrogen substances. Spirulina sp is the type of microalgae selected to utilize the wastewater of energy drink, the selection criteria is the size of Spirulina sp is relatively large and easy to separated from its solution. The experiment conducted by cultivate the seeding microalgae with certain nutrients until the certain volume. The synthetic wastewater obtained from one of energy drink type of powder with commercial brand as Kuku Bima Ener-G, the wastewater concentration selected under the close to the real condition of wastewater as basis of COD measurement (6 sachet/L or COD of 12.480mg/L) and aqueous concentration (1 sachet/L or COD of 2080mg/L). The batch experiments with 1L volume conducted and with variable of percent volume of wastewater added in order to observe the growth of microlagae. The response of the microalgae growth obtained by increasing the optical density of the microalgae solution and continued by calculation for the growth rate of microalgae. The result of the experiments indicated that for the aqueous concentration (1 sachet/L or COD of 2080mg/L) the optimum added of wastewater is 40 % with growrate of 0.55/day while for the concentrated wastewater (6 sachet/L or COD of 12.480mg/L), the optimum condition is 25 % wastewater added with growth rate of 0.43/day.

Lecithin-linker formulations for self-emulsifying delivery of nutraceuticals.

PubMed

Chu, Jacquelene; Cheng, Yu-Ling; Rao, A Venketeshwer; Nouraei, Mehdi; Zarate-Muñoz, Silvia; Acosta, Edgar J

2014-08-25

Lecithin-linker microemulsions are formulations produced with soybean lecithin in combination with a highly lipophilic (lipophilic linker) and highly hydrophilic (hydrophilic linkers) surfactant-like additives. In this work, lecithin-linker systems were formulated to produce self-emulsifying delivery systems for β-carotene and β-sitosterol. The concentration of the lipophilic linker, sorbitan monooleate, was adjusted to minimize the formation of liquid crystals. The concentration of hydrophilic linkers, decaglyceryl caprylate/caprate and PEG-6-caprylic/capric glycerides, was gradually increased (scanned) until single phase clear microemulsions were obtained. For these scans, the oil (ethyl caprate) to water ratio was set to 1. The single phase, clear microemulsions were diluted with fed-state simulated intestinal fluid (FeSSIF) and produced stable emulsions, with drop sizes close to 200 nm. Using pseudo-ternary phase diagrams to evaluate the process of dilution of microemulsion preconcentrates (mixtures of oil, lecithin and linkers with little or no water) with FeSSIF, it was determined that self-emulsifying systems are obtained when the early stages of the dilution produce single phase microemulsions. If liquid crystals or multiple phase systems are obtained during those early stages, then the emulsification yields unstable emulsions with large drop sizes. An in vitro permeability study conducted using a Flow-Thru Dialyzer revealed that stable emulsions with drop sizes of 150-300 nm produce large and irreversible permeation of β-carotene to sheep intestine. On the other hand, unstable emulsions produced without the linker combination separated in the dialyzer chamber. Copyright © 2014 Elsevier B.V. All rights reserved.

The dynamics of milk droplet-droplet collisions

NASA Astrophysics Data System (ADS)

Finotello, Giulia; Kooiman, Roeland F.; Padding, Johan T.; Buist, Kay A.; Jongsma, Alfred; Innings, Fredrik; Kuipers, J. A. M.

2018-01-01

Spray drying is an important industrial process to produce powdered milk, in which concentrated milk is atomized into small droplets and dried with hot gas. The characteristics of the produced milk powder are largely affected by agglomeration, combination of dry and partially dry particles, which in turn depends on the outcome of a collision between droplets. The high total solids (TS) content and the presence of milk proteins cause a relatively high viscosity of the fed milk concentrates, which is expected to largely influence the collision outcomes of drops inside the spray. It is therefore of paramount importance to predict and control the outcomes of binary droplet collisions. Only a few studies report on droplet collisions of high viscous liquids and no work is available on droplet collisions of milk concentrates. The current study therefore aims to obtain insight into the effect of viscosity on the outcome of binary collisions between droplets of milk concentrates. To cover a wide range of viscosity values, three milk concentrates (20, 30 and 46% TS content) are investigated. An experimental set-up is used to generate two colliding droplet streams with consistent droplet size and spacing. A high-speed camera is used to record the trajectories of the droplets. The recordings are processed by Droplet Image Analysis in MATLAB to determine the relative velocities and the impact geometries for each individual collision. The collision outcomes are presented in a regime map dependent on the dimensionless impact parameter and Weber ( We) number. The Ohnesorge ( Oh) number is introduced to describe the effect of viscosity from one liquid to another and is maintained constant for each regime map by using a constant droplet diameter ( d ˜ 700 μ m). In this work, a phenomenological model is proposed to describe the boundaries demarcating the coalescence-separation regimes. The collision dynamics and outcome of milk concentrates are compared with aqueous glycerol solutions experiments. While milk concentrates have complex chemical composition and rheology, glycerol solutions are Newtonian fluids and therefore easy to characterize. The collision morphologies of glycerol solutions and milk concentrates are similar, and the regime maps can be described by the same phenomenological model developed in this work. The regime of bouncing, however, was not observed for any of the milk concentrates.

Butanol production from food waste: a novel process for producing sustainable energy and reducing environmental pollution.

PubMed

Huang, Haibo; Singh, Vijay; Qureshi, Nasib

2015-01-01

Waste is currently a major problem in the world, both in the developing and the developed countries. Efficient utilization of food waste for fuel and chemical production can positively influence both the energy and environmental sustainability. This study investigated using food waste to produce acetone, butanol, and ethanol (ABE) by Clostridium beijerinckii P260. In control fermentation, 40.5 g/L of glucose (initial glucose 56.7 g/L) was used to produce 14.2 g/L of ABE with a fermentation productivity and a yield of 0.22 g/L/h and 0.35 g/g, respectively. In a similar fermentation 81 g/L of food waste (containing equivalent glucose of 60.1 g/L) was used as substrate, and the culture produced 18.9 g/L ABE with a high ABE productivity of 0.46 g/L/h and a yield of 0.38 g/g. Fermentation of food waste at higher concentrations (129, 181 and 228 g/L) did not remarkably increase ABE production but resulted in high residual glucose due to the culture butanol inhibition. An integrated vacuum stripping system was designed and applied to recover butanol from the fermentation broth simultaneously to relieve the culture butanol inhibition, thereby allowing the fermentation of food waste at high concentrations. ABE fermentation integrated with vacuum stripping successfully recovered the ABE from the fermentation broth and controlled the ABE concentrations below 10 g/L during fermentation when 129 g/L food waste was used. The ABE productivity with vacuum fermentation was 0.49 g/L/h, which was 109 % higher than the control fermentation (glucose based). More importantly, ABE vacuum recovery and fermentation allowed near-complete utilization of the sugars (~98 %) in the broth. In these studies it was demonstrated that food waste is a superior feedstock for producing butanol using Clostridium beijerinckii. Compared to costly glucose, ABE fermentation of food waste has several advantages including lower feedstock cost, higher productivity, and less residual sugars.

Arsenic in groundwater in eastern New England: Occurrence, controls, and human health implications

USGS Publications Warehouse

Ayotte, J.D.; Montgomery, D.L.; Flanagan, S.M.; Robinson, K.W.

2003-01-01

In eastern New England, high concentrations (greater than 10 ??g/L) of arsenic occur in groundwater. Privately supplied drinking water from bedrock aquifers often has arsenic concentrations at levels of concern to human health, whereas drinking water from unconsolidated aquifers is least affected by arsenic contamination. Water from wells in metasedimentary bedrock units, primarily in Maine and New Hampshire, has the highest arsenic concentrations - nearly 30% of wells in these aquifers produce water with arsenic concentrations greater than 10 ??g/L. Arsenic was also found at concentrations of 3-40 mg/kg in whole rock samples in these formations, suggesting a possible geologic source. Arsenic is most common in groundwater with high pH. High pH is related to groundwater age and possibly the presence of calcite in bedrock. Ion exchange in areas formerly inundated by seawater also may increase pH. Wells sampled twice during periods of 1-10 months have similar arsenic concentrations (slope = 0.89; r-squared = 0.97). On the basis of water-use information for the aquifers studied, about 103 000 people with private wells could have water supplies with arsenic at levels of concern (greater than 10 ??g/L) for human health.

Process in manufacturing high efficiency AlGaAs/GaAs solar cells by MO-CVD

NASA Technical Reports Server (NTRS)

Yeh, Y. C. M.; Chang, K. I.; Tandon, J.

1984-01-01

Manufacturing technology for mass producing high efficiency GaAs solar cells is discussed. A progress using a high throughput MO-CVD reactor to produce high efficiency GaAs solar cells is discussed. Thickness and doping concentration uniformity of metal oxide chemical vapor deposition (MO-CVD) GaAs and AlGaAs layer growth are discussed. In addition, new tooling designs are given which increase the throughput of solar cell processing. To date, 2cm x 2cm AlGaAs/GaAs solar cells with efficiency up to 16.5% were produced. In order to meet throughput goals for mass producing GaAs solar cells, a large MO-CVD system (Cambridge Instrument Model MR-200) with a susceptor which was initially capable of processing 20 wafers (up to 75 mm diameter) during a single growth run was installed. In the MR-200, the sequencing of the gases and the heating power are controlled by a microprocessor-based programmable control console. Hence, operator errors can be reduced, leading to a more reproducible production sequence.

Application of microalgae hydrolysate as a fermentation medium for microbial production of 2-pyrone 4,6-dicarboxylic acid.

PubMed

Htet, April N; Noguchi, Mana; Ninomiya, Kazuaki; Tsuge, Yota; Kuroda, Kosuke; Kajita, Shinya; Masai, Eiji; Katayama, Yoshihiro; Shikinaka, Kazuhiro; Otsuka, Yuichiro; Nakamura, Masaya; Honda, Ryo; Takahashi, Kenji

2018-06-01

Actual biomass of microalgae was tested as a fermentation substrate for microbial production of 2-pyrone 4,6-dicarboxylic acid (PDC). Acid-hydrolyzed green microalgae Chlorella emersonii (algae hydrolysate) was diluted to adjust the glucose concentration to 2 g/L and supplemented with the nutrients of Luria-Bertani (LB) medium (tryptone 10 g/L and yeast extract 5 g/L). When the algae hydrolysate was used as a fermentation source for recombinant Escherichia coli producing PDC, 0.43 g/L PDC was produced with a yield of 20.1% (mol PDC/mol glucose), whereas 0.19 g/L PDC was produced with a yield of 8.6% when LB medium supplemented with glucose was used. To evaluate the potential of algae hydrolysate alone as a fermentation medium for E. coli growth and PDC production, the nutrients of LB medium were reduced from the algae hydrolysate medium. Interestingly, 0.17 g/L PDC was produced even without additional nutrient, which was comparable to the case using pure glucose medium with nutrients of LB medium. When using a high concentration of hydrolysate without additional nutrients, 1.22 g/L PDC was produced after a 24-h cultivation with the yield of 16.1%. Overall, C. emersonii has high potential as cost-effective fermentation substrate for the microbial production of PDC. Copyright © 2018 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Noble gas trapping and fractionation during synthesis of carbonaceous matter. [in meteorites

NASA Technical Reports Server (NTRS)

Frick, U.; Mack, R.; Chang, S.

1979-01-01

An investigation of noble gas entrapment during synthesis of carbonaceous, macromolecular, and kerogen-like substances is presented. High molecular weight organic matter synthesized in aqueous condensation reactions contained little gas, and the composition was consistent with fractionation due to noble gas solubility in water; however, propane soot produced during a modified Miller-Urey experiment in an aritificial gas mixture contained high concentrations of trapped noble gases that displayed strong elemental fractionation from their reservoirs. It is concluded that theses experiemnts show that processes exist for synthesis of carbonaceous carriers that result in high noble gas concentrations and strong elemental fractionation at temperatures well above those required by absorption to achieve similar effects.

Physics of Fresh Produce Safety: Role of Diffusion and Tissue Reaction in Sanitization of Leafy Green Vegetables with Liquid and Gaseous Ozone-Based Sanitizers.

PubMed

Shynkaryk, Mykola V; Pyatkovskyy, Taras; Mohamed, Hussein M; Yousef, Ahmed E; Sastry, Sudhir K

2015-12-01

Produce safety has received much recent attention, with the emphasis being largely on discovery of how microbes invade produce. However, the sanitization operation deserves more attention than it has received. The ability of a sanitizer to reach the site of pathogens is a fundamental prerequisite for efficacy. This work addresses the transport processes of ozone (gaseous and liquid) sanitizer for decontamination of leafy greens. The liquid sanitizer was ineffective against Escherichia coli K-12 in situations where air bubbles may be trapped within cavities. A model was developed for diffusion of sanitizer into the interior of produce. The reaction rate of ozone with the surface of a lettuce leaf was determined experimentally and was used in a numerical simulation to evaluate ozone concentrations within the produce and to determine the time required to reach different locations. For aqueous ozone, the penetration depth was limited to several millimeters by ozone self-decomposition due to the significant time required for diffusion. In contrast, gaseous sanitizer was able to reach a depth of 100 mm in several minutes without depletion in the absence of reaction with surfaces. However, when the ozone gas reacted with the produce surface, gas concentration was significantly affected. Simulation data were validated experimentally by measuring ozone concentrations at the bottom of a cylinder made of lettuce leaf. The microbiological test confirmed the relationship between ozone transport, its self-decomposition, reaction with surrounding materials, and the degree of inactivation of E. coli K-12. Our study shows that decontamination of fresh produce, through direct contact with the sanitizer, is more feasible with gaseous than with aqueous sanitizers. Therefore, sanitization during a high-speed washing process is effective only for decontaminating the wash water.

Effect of Land Use, Seasonality, and Hydrometeorological Conditions on the K+ Concentration-Discharge Relationship During Different Types of Floods in Carpathian Foothills Catchments (Poland).

PubMed

Siwek, Joanna P; Żelazny, Mirosław; Siwek, Janusz; Szymański, Wojciech

2017-01-01

The purpose of the study was to determine the role of land use, seasonality, and hydrometeorological conditions on the relationship between stream water potassium (K + ) concentration and discharge during different types of floods-short- and long-duration rainfall floods as well as snowmelt floods on frozen and thawed soils. The research was conducted in small catchments (agricultural, woodland, mixed-use) in the Carpathian Foothills (Poland). In the woodland catchment, lower K + concentrations were noted for each given specific runoff value for summer rainfall floods versus snowmelt floods (seasonal effect). In the agricultural and mixed-use catchments, the opposite was true due to their greater ability to flush K + out of the soil in the summer. In the stream draining woodland catchment, higher K + concentrations occurred during the rising limb than during the falling limb of the hydrograph (clockwise hysteresis) for all flood types, except for snowmelt floods with the ground not frozen. In the agricultural catchment, clockwise hystereses were produced for short- and long-duration rainfall floods caused by high-intensity, high-volume rainfall, while anticlockwise hystereses were produced for short- and long-duration rainfall floods caused by low-intensity, low-volume rainfall as well as during snowmelt floods with the soil frozen and not frozen. In the mixed-use catchment, the hysteresis direction was also affected by different lag times for water reaching stream channels from areas with different land use. K + hystereses for the woodland catchment were more narrow than those for the agricultural and mixed-use catchments due to a smaller pool of K + in the woodland catchment. In all streams, the widest hystereses were produced for rainfall floods preceded by a long period without rainfall.

Magma Electrolysis: An update

NASA Technical Reports Server (NTRS)

Colson, Russell O.; Haskin, Larry A.

1991-01-01

Electrolytic extraction of O2 from molten lunar soil is conceptually simple and thus a candidate process for producing O2 on the Moon. Possible container and electrode materials are being tested for durability in corrosive high-temperature silicate melts and looking for complications that might increase energy requirements. Gaseous oxygen is being produced by electrolysis of 1-2 gram quantities of silicate melts in spinel (MgAl2O4) crucibles; in these melts, spinel is a stable phase. The concentration of FeO was kept low because FeO decrease O2 production efficiency. Platinum electrodes were placed about 0.5 cm apart in the melt. The spinel crucible was still intact after 40 minutes of electrolysis, when the experiment was halted for examination. The Pt anode was also intact; its Pt was maintained in a dynamci state in which the anode was continuously oxidized but quickly reduced again by the silicate melt, inhibiting migration of Pt away from the anode. In melts with low concentrations of Al2O3 + SiO2 (2 wt percent), the energy of resistance heating was only approximately equal to 10 to 20 percent of the theoretical amount required to produce O2. In melts substantially more concentrated in Al2O3 + SiO2, higher melt viscosity resulted in frothing that, in the worst case, caused high enough melt resistivities to raise the energy requirements to nearly 10 times theoretical. Both Fe and Si are produced at the cathode; in iron-rich melts, a- and c-iron and molten ferrosilicon were observed. Production was also observed at the cathode of a previously unrecognized gas; which is not yet identified. The solubility of metallic species was measured in silicate melts. They are too low to reduce significantly the efficiency of O2 production.

Environmental pollution with antimicrobial agents from bulk drug manufacturing industries in Hyderabad, South India, is associated with dissemination of extended-spectrum beta-lactamase and carbapenemase-producing pathogens.

PubMed

Lübbert, Christoph; Baars, Christian; Dayakar, Anil; Lippmann, Norman; Rodloff, Arne C; Kinzig, Martina; Sörgel, Fritz

2017-08-01

High antibiotic and antifungal concentrations in wastewater from anti-infective drug production may exert selection pressure for multidrug-resistant (MDR) pathogens. We investigated the environmental presence of active pharmaceutical ingredients and their association with MDR Gram-negative bacteria in Hyderabad, South India, a major production area for the global bulk drug market. From Nov 19 to 28, 2016, water samples were collected from the direct environment of bulk drug manufacturing facilities, the vicinity of two sewage treatment plants, the Musi River, and habitats in Hyderabad and nearby villages. Samples were analyzed for 25 anti-infective pharmaceuticals with liquid chromatography-tandem mass spectrometry and for MDR Gram-negative bacteria using chromogenic culture media. In addition, specimens were screened with PCR for bla VIM , bla KPC , bla NDM , bla IMP-1 , and bla OXA-48 resistance genes. All environmental specimens from 28 different sampling sites were contaminated with antimicrobials. High concentrations of moxifloxacin, voriconazole, and fluconazole (up to 694.1, 2500, and 236,950 µg/L, respectively) as well as increased concentrations of eight other antibiotics were found in sewers in the Patancheru-Bollaram industrial area. Corresponding microbiological analyses revealed an extensive presence of extended-spectrum beta-lactamase and carbapenemase-producing Enterobacteriaceae and non-fermenters (carrying mainly bla OXA-48 , bla NDM , and bla KPC ) in more than 95% of the samples. Insufficient wastewater management by bulk drug manufacturing facilities leads to unprecedented contamination of water resources with antimicrobial pharmaceuticals, which seems to be associated with the selection and dissemination of carbapenemase-producing pathogens. The development and global spread of antimicrobial resistance present a major challenge for pharmaceutical producers and regulatory agencies.

Cyanobacteria and Cyanotoxins Occurrence and Removal from Five High-Risk Conventional Treatment Drinking Water Plants

PubMed Central

Szlag, David C.; Sinclair, James L.; Southwell, Benjamin; Westrick, Judy A.

2015-01-01

An environmental protection agency EPA expert workshop prioritized three cyanotoxins, microcystins, anatoxin-a, and cylindrospermopsin (MAC), as being important in freshwaters of the United States. This study evaluated the prevalence of potentially toxin producing cyanobacteria cell numbers relative to the presence and quantity of the MAC toxins in the context of this framework. Total and potential toxin producing cyanobacteria cell counts were conducted on weekly raw and finished water samples from utilities located in five US states. An Enzyme-Linked Immunosorbant Assay (ELISA) was used to screen the raw and finished water samples for microcystins. High-pressure liquid chromatography with a photodiode array detector (HPLC/PDA) verified microcystin concentrations and quantified anatoxin-a and cylindrospermopsin concentrations. Four of the five utilities experienced cyanobacterial blooms in their raw water. Raw water samples from three utilities showed detectable levels of microcystins and a fourth utility had detectable levels of both microcystin and cylindrospermopsin. No utilities had detectable concentrations of anatoxin-a. These conventional plants effectively removed the cyanobacterial cells and all finished water samples showed MAC levels below the detection limit by ELISA and HPLC/PDA. PMID:26075379

Pharmacokinetics and Safety of MP-376 (Levofloxacin Inhalation Solution) in Cystic Fibrosis Subjects▿

PubMed Central

Geller, David E.; Flume, Patrick A.; Griffith, David C.; Morgan, Elizabeth; White, Dan; Loutit, Jeffery S.; Dudley, Michael N.

2011-01-01

The pharmacokinetics and tolerability of nebulized MP-376 (levofloxacin inhalation solution [Aeroquin]) were determined in cystic fibrosis (CF) subjects. Ten CF subjects received single 180-mg doses of two formulations of MP-376, followed by a multiple-dose phase of 240 mg once daily for 7 days. Serum and expectorated-sputum samples were assayed for levofloxacin content. Safety was evaluated following the single- and multiple-dose study phases. Nebulized MP-376 produced high concentrations of levofloxacin in sputum. The mean maximum plasma concentration (Cmax) ranged between 2,563 and 2,932 mg/liter for 180-mg doses of the 50- and 100-mg/ml formulations, respectively. After 7 days of dosing, the mean Cmax for the 240-mg dose was 4,691 mg/liter. The mean serum levofloxacin Cmax ranged between 0.95 and 1.28 for the 180-mg doses and was 1.71 for the 240-mg dose. MP-376 was well tolerated. Nebulized MP-376 produces high sputum and low serum levofloxacin concentrations. The pharmacokinetics, safety, and tolerability were similar for the two formulations. MP-376 240 mg (100 mg/ml) is being advanced into late-stage clinical development. PMID:21444699

Fermentation of soybean hulls to ethanol while retaining protein value

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mielenz, Jonathan R; Wyman, Professor Charles E; John, Bardsley

2009-01-01

Soybean hulls were evaluated as a resource for production of ethanol by the simultaneous saccharification and fermentation (SSF) process, and no pretreatment of the hulls was found to be needed to realize high ethanol yields with S. cerevisiae D5A. The impact of cellulase, -glucosidase and pectinase dosages were determined at a 15% biomass loading, and ethanol concentrations of 25-30 g/L were routinely obtained, while under these conditions corn stover, wheat straw, and switchgrass produced 3-4 times lower ethanol yields. Removal of carbohydrates also concentrated the hull protein to over 25% w/w from the original roughly 10%. Analysis of the soybeanmore » hulls before and after fermentation showed similar amino acid profiles including an increase in the essential amino acids lysine and threonine in the residues. Thus, eliminating pretreatment should assure that the protein in the hulls is preserved, and conversion of the carbohydrates to ethanol with high yields produces a more concentrated and valuable co-product in addition to ethanol. The resulting upgraded feed product from soybean hulls would likely to be acceptable to monogastric as well as bovine livestock.« less

Production of Concentrated Pickering Emulsions with Narrow Size Distributions Using Stirred Cell Membrane Emulsification.

PubMed

Manga, Mohamed S; York, David W

2017-09-12

Stirred cell membrane emulsification (SCME) has been employed to prepare concentrated Pickering oil in water emulsions solely stabilized by fumed silica nanoparticles. The optimal conditions under which highly stable and low-polydispersity concentrated emulsions using the SCME approach are highlighted. Optimization of the oil flux rates and the paddle stirrer speeds are critical to achieving control over the droplet size and size distribution. Investigating the influence of oil volume fraction highlights the criticality of the initial particle loading in the continuous phase on the final droplet size and polydispersity. At a particle loading of 4 wt %, both the droplet size and polydispersity increase with increasing of the oil volume fraction above 50%. As more interfacial area is produced, the number of particles available in the continuous phase diminishes, and coincidently a reduction in the kinetics of particle adsorption to the interface resulting in larger polydisperse droplets occurs. Increasing the particle loading to 10 wt % leads to significant improvements in both size and polydispersity with oil volume fractions as high as 70% produced with coefficient of variation values as low as ∼30% compared to ∼75% using conventional homogenization techniques.

Burkholderia sacchari DSM 17165: A source of compositionally-tunable block-copolymeric short-chain poly(hydroxyalkanoates) from xylose and levulinic acid.

PubMed

Ashby, Richard D; Solaiman, Daniel K Y; Nuñez, Alberto; Strahan, Gary D; Johnston, David B

2018-04-01

Burkholderia sacchari was used to produce poly-3-hydroxybutyrate-co-3-hydroxyvalerate block copolymers from xylose and levulinic acid. Levulinic acid was the preferred substrate resulting in 3-hydroxyvalerate (3HV) contents as high as 95 mol% at 24 h. The 3HB:3HV ratios were controlled by the initial levulinic acid media concentration and fermentation length. Higher levulinic acid concentrations and longer durations, resulted in polymers with two glass transition temperatures, each approximating those associated with poly-3HB and poly-3HV. 13 C NMR confirmed the presence of high concentrations of 3HB-3HB and 3HV-3HV homopolymeric dyads, while mass spectrometry of the partial hydrolysis products did not conform to Bernoullian statistics for randomness, confirming block sequences. MS/MS analysis of specific oligomers showed the mass-loss of 86 amu (a 3HB unit) and 100 amu (a 3HV unit) attesting to some randomness within the polymers. This study verifies the potential for producing Poly-3HB-block-3HV copolymers from inexpensive biorenewable feedstocks without sequential addition of carbon sources. Published by Elsevier Ltd.

Occupational exposure to airborne fungi among rice mill workers with special reference to aflatoxin producing A. flavus strains.

PubMed

Desai, Manisha Rajib; Ghosh, Sandip

2003-01-01

A study was undertaken on environmental mycoflora of rice mills situated in Bawla town, Ahmedabad district. The airborne fungal communities were isolated and identified quantitatively by using Andersen-6-stage viable sampler, midget impinger and high volume samplers (Cone and Hexhlet for total and respirable dusts respectively). Of all the isolates, genus Aspergillus was predominant and among the Aspergillus species, A. flavus was the common isolate, irrespective of the method applied for sample collection. Number of isolates recovered from the working place was significantly greater (p < 0.01) compared to control. Total percentage of aflatoxin positive strains of A. flavus was 8 %. These aflatoxin producing strains were identified on various media, such as Czapek agar (Cz) with 0.05 % anisaldehyde, APA and CAM. Surface morphology of aflatoxin positive strains was studied by SEM. Highly significant total and respirable dust concentrations were found in the work place (p < 0.01) whereas in the store, only the total dust concentration was significantly higher (p < 0.05) than the control site. The study indicates that the rice mill workers are occupationally exposed to airborne aflatoxin producing strains of A. flavus. Thus, they require protective mask for their safety.

Large-Scale Selection and Breeding To Generate Industrial Yeasts with Superior Aroma Production

PubMed Central

Steensels, Jan; Meersman, Esther; Snoek, Tim; Saels, Veerle

2014-01-01

The concentrations and relative ratios of various aroma compounds produced by fermenting yeast cells are essential for the sensory quality of many fermented foods, including beer, bread, wine, and sake. Since the production of these aroma-active compounds varies highly among different yeast strains, careful selection of variants with optimal aromatic profiles is of crucial importance for a high-quality end product. This study evaluates the production of different aroma-active compounds in 301 different Saccharomyces cerevisiae, Saccharomyces paradoxus, and Saccharomyces pastorianus yeast strains. Our results show that the production of key aroma compounds like isoamyl acetate and ethyl acetate varies by an order of magnitude between natural yeasts, with the concentrations of some compounds showing significant positive correlation, whereas others vary independently. Targeted hybridization of some of the best aroma-producing strains yielded 46 intraspecific hybrids, of which some show a distinct heterosis (hybrid vigor) effect and produce up to 45% more isoamyl acetate than the best parental strains while retaining their overall fermentation performance. Together, our results demonstrate the potential of large-scale outbreeding to obtain superior industrial yeasts that are directly applicable for commercial use. PMID:25192996

Locating the Dropout Crisis. Which High Schools Produce the Nation's Dropouts? Where Are They Located? Who Attends Them? Report 70

ERIC Educational Resources Information Center

Balfanz, Robert; Legters, Nettie

2004-01-01

The purpose of this report was to locate the dropout crisis- to determine its scale and scope by identifying the number of high schools with severe dropout problems, detailing the states, cities, and locales where they are concentrated, and establishing who attends them. For this analysis of high schools across the country, two cut-points were…

Improving Air Pollution Modeling Over The Po Valley Using Saharan Dust Transport Forecasts

NASA Astrophysics Data System (ADS)

Kishcha, P.; Carnevale, C.; Finzi, G.; Pisoni, E.; Volta, M.; Nickovic, S.; Alpert, P.

2012-04-01

Our study shows that Saharan dust can contribute significantly to PM10 concentrations in the Po Valley. This dust contribution should be taken into account when estimating the exceedance of pollution limits. The DREAM dust model has been used for several years for producing operational dust forecasts at Tel-Aviv University, Israel. DREAM has been producing daily forecasts of 3-D distribution of dust concentrations over the Mediterranean region, Middle East, Europe, and over the Atlantic Ocean (http://wind.tau.ac.il/dust8/dust.html). In the current study, DREAM dust forecasts were used to give better model estimates of the contribution of Saharan dust to PM10 concentration over the Po Valley, in Northern Italy. This was carried out by the integration of daily Saharan dust forecasts into a mesoscale Transport Chemical Aerosol Model (TCAM). The Po Valley in Northern Italy is frequently affected by high PM10 concentrations, where both natural and anthropogenic sources play a significant role. Our study of TCAM and DREAM integration was carried out for the period May 15 - June 30, 2007, when four significant dust events were observed. The integrated TCAM-DREAM model performance was evaluated by comparing PM10 measurements with modeled PM10 concentrations. First, Saharan dust impact on TCAM performance was analyzed at eleven remote PM10 sites which had the lowest level of air pollution (PM10 ≤ 14 μg/m3) over the period under consideration. For those remote sites, the observed high PM10 concentrations during dust events stood prominently on the background of low PM10 concentrations. At the remote sites, such a strong deviation from the background level can not be attributed to anthropogenic aerosol emissions because of their distance from anthropogenic sources. The observed maxima in PM10 concentration during dust events is evidence of dust aerosol near the surface in Northern Italy. During all dust events under consideration, the integrated TCAM-DREAM model produced more accurate PM10 concentrations than the base TCAM model. Then, a comparison between modeled concentrations and PM10 measurements was carried out at 230 PM10 monitoring sites, distributed within the model domain. This model-vs.-measurement comparison showed that the integrated TCAM -DREAM model more accurately reproduced PM10 concentrations than the base TCAM model, both in term of correlation and mean error. Our results are of importance to countries which have to pay a penalty for exceeding the pollution limit. By extracting dust contribution from PM10 measurements, these countries could show lower rates of man-made pollution.

Fermentative behavior of Saccharomyces strains during microvinification of raspberry juice (Rubus idaeus L.).

PubMed

Duarte, Whasley F; Dragone, Giuliano; Dias, Disney R; Oliveira, José M; Teixeira, José A; Silva, João B Almeida E; Schwan, Rosane F

2010-10-15

Sixteen different strains of Saccharomyces cerevisiae and Saccharomyces bayanus were evaluated in the production of raspberry fruit wine. Raspberry juice sugar concentrations were adjusted to 16° Brix with a sucrose solution, and batch fermentations were performed at 22 °C. Various kinetic parameters, such as the conversion factors of the substrates into ethanol (Y(p/s)), biomass (Y(x/s)), glycerol (Y(g/s)) and acetic acid (Y(ac/s)), the volumetric productivity of ethanol (Q(p)), the biomass productivity (P(x)), and the fermentation efficiency (E(f)) were calculated. Volatile compounds (alcohols, ethyl esters, acetates of higher alcohols and volatile fatty acids) were determined by gas chromatography (GC-FID). The highest values for the E(f), Y(p/s), Y(g/s), and Y(x/s) parameters were obtained when strains commonly used in the fuel ethanol industry (S. cerevisiae PE-2, BG, SA, CAT-1, and VR-1) were used to ferment raspberry juice. S. cerevisiae strain UFLA FW 15, isolated from fruit, displayed similar results. Twenty-one volatile compounds were identified in raspberry wines. The highest concentrations of total volatile compounds were found in wines produced with S. cerevisiae strains UFLA FW 15 (87,435 μg/L), CAT-1 (80,317.01 μg/L), VR-1 (67,573.99 μg/L) and S. bayanus CBS 1505 (71,660.32 μg/L). The highest concentrations of ethyl esters were 454.33 μg/L, 440.33 μg/L and 438 μg/L for S. cerevisiae strains UFLA FW 15, VR-1 and BG, respectively. Similar to concentrations of ethyl esters, the highest concentrations of acetates (1927.67 μg/L) and higher alcohols (83,996.33 μg/L) were produced in raspberry wine from S. cerevisiae UFLA FW 15. The maximum concentration of volatile fatty acids was found in raspberry wine produced by S. cerevisiae strain VR-1. We conclude that S. cerevisiae strain UFLA FW 15 fermented raspberry juice and produced a fruit wine with low concentrations of acids and high concentrations of acetates, higher alcohols and ethyl esters. Copyright © 2010 Elsevier B.V. All rights reserved.

The ntrB and ntrC Genes Are Involved in the Regulation of Poly-3-Hydroxybutyrate Biosynthesis by Ammonia in Azospirillum brasilense Sp7

PubMed Central

Sun, Jun; Peng, Xuan; Van Impe, Jan; Vanderleyden, Jos

2000-01-01

Azospirillum brasilense Sp7 and its ntrA (rpoN), ntrBC, and ntrC mutants have been evaluated for their capabilities of poly-3-hydroxybutyrate (PHB) accumulation in media with high and low ammonia concentrations. It was observed that the ntrBC and ntrC mutants can produce PHB in both low- and high-C/N-ratio media, while no significant PHB production was observed for the wild type or the ntrA mutant in low-C/N-ratio media. Further investigation by fermentation analysis indicated that the ntrBC and ntrC mutants were able to grow and accumulate PHB simultaneously in the presence of a high concentration of ammonia in the medium, while little PHB was produced in the wild type and ntrA (rpoN) mutant during active growth phase. These results provide the first genetic evidence that the ntrB and ntrC genes are involved in the regulation of PHB synthesis by ammonia in A. brasilense Sp7. PMID:10618211

Effect of osmotic dehydration and vacuum-frying parameters to produce high-quality mango chips.

PubMed

Nunes, Yolanda; Moreira, Rosana G

2009-09-01

Mango (Mangifera indica L.) is a fruit rich in flavor and nutritional values, which is an excellent candidate for producing chips. The objective of this study was to develop high-quality mango chips using vacuum frying. Mango ("Tommy Atkins") slices were pretreated with different maltodextrin concentrations (40, 50, and 65, w/v), osmotic dehydration times (45, 60, and 70 min), and solution temperatures (22 and 40 degrees C). Pretreated slices were vacuum fried at 120, 130, and 138 degrees C and product quality attributes (oil content, texture, color, carotenoid content) determined. The effect of frying temperatures at optimum osmotic dehydration times (65 [w/v] at 40 degrees C) was assessed. All samples were acceptable (scores > 5) to consumer panelists. The best mango chips were those pretreated with 65 (w/v) concentration for 60 min and vacuum fried at 120 degrees C. Mango chips under atmospheric frying had less carotenoid retention (32%) than those under vacuum frying (up to 65%). These results may help further optimize vacuum-frying processing of high-quality fruit-based snacks.

Rapid activation of the interferon system in vivo.

PubMed Central

Dianzani, F; Gullino, P; Baron, S

1978-01-01

Experiments were carried out to study the kinetics of local interferon production in the subcutaneous tissues of rats stimulated with Newcastle disease virus. Specifically, the interferon produced and released in the extracellular fluids was collected at various intervals of time in micropore chambers implanted into the subcutaneous tissue of rats. Interferon was detected at moderate titers 1 h after induction, and it was present at high titer at 2 h. The interferon levels remained remarkably high in the samples collected after 3, 5, and 24 h, and in some rats it was still detectable after 48 and 72 h. Since control experiments showed that it requires 2 to 3 h for interferon to penetrate the chambers, it may be concluded that high concentrations of interferon are present in the extracellular fluid within 1 h of induction. The evaluation of the kinetics of production and of the concentrations attained in the extracellular fluid suggests that in a solid tissue a cell infected by a potent interferon inducer may produce interferon early enough and in sufficient quantity to protect neighboring cells before the production of progeny virions. PMID:669799

Ethanol production from food waste at high solids content with vacuum recovery technology.

PubMed

Huang, Haibo; Qureshi, Nasib; Chen, Ming-Hsu; Liu, Wei; Singh, Vijay

2015-03-18

Ethanol production from food wastes does not only solve environmental issues but also provides renewable biofuels. This study investigated the feasibility of producing ethanol from food wastes at high solids content (35%, w/w). A vacuum recovery system was developed and applied to remove ethanol from fermentation broth to reduce yeast ethanol inhibition. A high concentration of ethanol (144 g/L) was produced by the conventional fermentation of food waste without a vacuum recovery system. When the vacuum recovery is applied to the fermentation process, the ethanol concentration in the fermentation broth was controlled below 100 g/L, thus reducing yeast ethanol inhibition. At the end of the conventional fermentation, the residual glucose in the fermentation broth was 5.7 g/L, indicating incomplete utilization of glucose, while the vacuum fermentation allowed for complete utilization of glucose. The ethanol yield for the vacuum fermentation was found to be 358 g/kg of food waste (dry basis), higher than that for the conventional fermentation at 327 g/kg of food waste (dry basis).

Rapid detection of cardiac troponin I using antibody-immobilized gate-pulsed AlGaN/GaN high electron mobility transistor structures

NASA Astrophysics Data System (ADS)

Yang, Jiancheng; Carey, Patrick; Ren, Fan; Wang, Yu-Lin; Good, Michael L.; Jang, Soohwan; Mastro, Michael A.; Pearton, S. J.

2017-11-01

We report a comparison of two different approaches to detecting cardiac troponin I (cTnI) using antibody-functionalized AlGaN/GaN High Electron Mobility Transistors (HEMTs). If the solution containing the biomarker has high ionic strength, there can be difficulty in detection due to charge-screening effects. To overcome this, in the first approach, we used a recently developed method involving pulsed biases applied between a separate functionalized electrode and the gate of the HEMT. The resulting electrical double layer produces charge changes which are correlated with the concentration of the cTnI biomarker. The second approach fabricates the sensing area on a glass slide, and the pulsed gate signal is externally connected to the nitride HEMT. This produces a larger integrated change in charge and can be used over a broader range of concentrations without suffering from charge-screening effects. Both approaches can detect cTnI at levels down to 0.01 ng/ml. The glass slide approach is attractive for inexpensive cartridge-type sensors.

High Throughput PBPK: Evaluating EPA's Open-Source Data and Tools for Dosimetry and Exposure Reconstruction (SOT)

EPA Science Inventory

To address this need, new tools have been created for characterizing, simulating, and evaluating chemical biokinetics. Physiologically-based pharmacokinetic (PBPK) models provide estimates of chemical exposures that produce potentially hazardous tissue concentrations, while tissu...

Development and Testing of a Power Trough System Using a Structurally-Efficient, High-Performance, Large-Aperture Concentrator with Thin Glass Reflector and Focal Point Rotation

DOE Office of Scientific and Technical Information (OSTI.GOV)

May, E. K.; Forristall, R.

2005-11-01

Industrial Solar Technology has assembled a team of experts to develop a large-aperture parabolic trough for the electric power market that moves beyond cost and operating limitations of 1980's designs based on sagged glass reflectors. IST's structurally efficient space frame design will require nearly 50% less material per square meter than a Solel LS-2 concentrator and the new trough will rotate around the focal point. This feature eliminates flexhoses that increase pump power, installation and maintenance costs. IST aims to deliver a concentrator module costing less than $100 per square meter that can produce temperatures up to 400 C. Themore » IST concentrator is ideally suited for application of front surface film reflectors and ensures that US corporations will manufacture major components, except for the high temperature receivers.« less

Rapid Induction of High-Level Carbapenem Resistance in Heteroresistant KPC-Producing Klebsiella pneumoniae

PubMed Central

Adams-Sapper, Sheila; Nolen, Shantell; Donzelli, Grace Fox; Lal, Mallika; Chen, Kunihiko; Justo da Silva, Livia Helena; Moreira, Beatriz M.

2015-01-01

Enterobacteriaceae strains producing the Klebsiella pneumoniae carbapenemase (KPC) have disseminated worldwide, causing an urgent threat to public health. KPC-producing strains often exhibit low-level carbapenem resistance, which may be missed by automated clinical detection systems. In this study, eight Klebsiella pneumoniae strains with heterogeneous resistance to imipenem were used to elucidate the factors leading from imipenem susceptibility to high-level resistance as defined by clinical laboratory testing standards. Time-kill analysis with an inoculum as low as 3 × 106 CFU/ml and concentrations of imipenem 8- and 16-fold higher than the MIC resulted in the initial killing of 99.9% of the population. However, full recovery of the population occurred by 20 h of incubation in the same drug concentrations. Population profiles showed that recovery was mediated by a heteroresistant subpopulation at a frequency of 2 × 10−7 to 3 × 10−6. Samples selected 2 h after exposure to imipenem were as susceptible as the unexposed parental strain and produced the major outer membrane porin OmpK36. However, between 4 to 8 h after exposure, OmpK36 became absent, and the imipenem MIC increased at least 32-fold. Individual colonies isolated from cultures after 20 h of exposure revealed both susceptible and resistant subpopulations. Once induced, however, the high-level imipenem resistance was maintained, and OmpK36 remained unexpressed even without continued carbapenem exposure. This study demonstrates the essential coordination between blaKPC and ompK36 expression mediating high-level imipenem resistance from a population of bacteria that initially exhibits a carbapenem-susceptibility phenotype. PMID:25801565

Effect of linoleic acid concentration on conjugated linoleic acid production by Butyrivibrio fibrisolvens A38.

PubMed

Kim, Y J; Liu, R H; Bond, D R; Russell, J B

2000-12-01

Butyrivibrio fibrisolvens A38 inocula were inhibited by as little as 15 microM linoleic acid (LA), but growing cultures tolerated 10-fold more LA before growth was inhibited. Growing cultures did not produce significant amounts of cis-9, trans-11 conjugated linoleic acid (CLA) until the LA concentration was high enough to inhibit biohydrogenation, growth was inhibited, and lysis was enhanced. Washed-cell suspensions that were incubated anaerobically with 350 microM LA converted most of the LA to hydrogenated products, and little CLA was detected. When the washed-cell suspensions were incubated aerobically, biohydrogenation was inhibited, CLA production was at least twofold greater, and CLA persisted. The LA isomerase reaction was very rapid, but the LA isomerase did not recycle like a normal enzyme to catalyze more substrate. Cells that were preincubated with CLA lost their ability to produce more CLA from LA, and the CLA accumulation was directly proportional (r(2) = 0.98) to the initial cell density. Growing cells were as sensitive to CLA as LA, the LA isomerase and reductases of biohydrogenation were linked, and free CLA was not released. Because growing cultures of B. fibrisolvens A38 did not produce significant amounts of CLA until the LA concentration was high, biohydrogenation was arrested, and the cell density had declined, the flow of CLA from the rumen may be due to LA-dependent bacterial inactivation, death, or lysis.

Effect of Linoleic Acid Concentration on Conjugated Linoleic Acid Production by Butyrivibrio fibrisolvens A38

PubMed Central

Kim, Young Jun; Liu, Rui Hai; Bond, Daniel R.; Russell, James B.

2000-01-01

Butyrivibrio fibrisolvens A38 inocula were inhibited by as little as 15 μM linoleic acid (LA), but growing cultures tolerated 10-fold more LA before growth was inhibited. Growing cultures did not produce significant amounts of cis-9, trans-11 conjugated linoleic acid (CLA) until the LA concentration was high enough to inhibit biohydrogenation, growth was inhibited, and lysis was enhanced. Washed-cell suspensions that were incubated anaerobically with 350 μM LA converted most of the LA to hydrogenated products, and little CLA was detected. When the washed-cell suspensions were incubated aerobically, biohydrogenation was inhibited, CLA production was at least twofold greater, and CLA persisted. The LA isomerase reaction was very rapid, but the LA isomerase did not recycle like a normal enzyme to catalyze more substrate. Cells that were preincubated with CLA lost their ability to produce more CLA from LA, and the CLA accumulation was directly proportional (r2 = 0.98) to the initial cell density. Growing cells were as sensitive to CLA as LA, the LA isomerase and reductases of biohydrogenation were linked, and free CLA was not released. Because growing cultures of B. fibrisolvens A38 did not produce significant amounts of CLA until the LA concentration was high, biohydrogenation was arrested, and the cell density had declined, the flow of CLA from the rumen may be due to LA-dependent bacterial inactivation, death, or lysis. PMID:11097894

The Effect of Micro/Nano-metrics Size on the Interaction of Jordanian Aluminosilicate Raw Materials with High pH Solution

NASA Astrophysics Data System (ADS)

Aldabsheh, Islam; Garcia-Valles, Maite; Martinez, Salvador

2014-05-01

Environmental preservation has become a driving force behind the search for new sustainable and environmentally friendly composites to replace conventional concrete produced from ordinary Portland cement (OPC). Current researches concentrate on developing building products (geopolymers) through geopolymerization. The goal is to produce low cost construction materials for green housing. Geopolymerization is the process of polymerizing minerals with high silica and alumina at low temperature by the use of alkali solutions. Dissolution is the most important process for supplying the high initial Al and Si concentrations to produce the gel phase that is responsible for geopolymerization. This study has been focused on the influence of different micrometric particle sizes of three Jordanian raw materials on their dissolution behavior in sodium hydroxide solution. The samples are kaolinite, volcanic tuff and silica sand. The dissolution properties of each material, alone and mixed with the other two materials were studied in different concentrations (5 and 10 M) using (NaOH) at 25ºC, and shaking time for 24 and 168 h. To better understand the dissolution process, the alkaline solution was renewed after the desired time in order to know if the Al-Si raw material is completely dissolved or not. Different analytical techniques were used to characterize raw materials physically, mineralogically, chemically and thermally. All processed samples either centrifuged solutions or solid residues were fully characterized. The leached concentrations of Al and Si were determined by inductively coupled plasma (ICP). X-ray Diffraction Technique (XRD), Scanning Electron Microscopy (SEM), and Thermo Gravimetric Analysis (TGA) were used to evaluate the solid residue characterization compared with the original ones. The three aluminosilicate raw materials have indicated variable degrees of solubility under highly alkaline conditions. The method for the size reduction of the used raw materials achieved by using a ball mill increased the dissolution rate owing to the increased surface area of the material or particle exposed to the solvent. The used Jordanian raw materials are potential to be used for geopolymerization. This work was partly financed by SGR 2009SGR-00444

Simultaneous removal of NO and SO2 using vacuum ultraviolet light (VUV)/heat/peroxymonosulfate (PMS).

PubMed

Liu, Yangxian; Wang, Yan; Wang, Qian; Pan, Jianfeng; Zhang, Jun

2018-01-01

Simultaneous removal process of SO 2 and NO from flue gas using vacuum ultraviolet light (VUV)/heat/peroxymonosulfate (PMS) in a VUV spraying reactor was proposed. The key influencing factors, active species, reaction products and mechanism of SO 2 and NO simultaneous removal were investigated. The results show that vacuum ultraviolet light (185 nm) achieves the highest NO removal efficiency and yield of and under the same test conditions. NO removal is enhanced at higher PMS concentration, light intensity and oxygen concentration, and is inhibited at higher NO concentration, SO 2 concentration and solution pH. Solution temperature has a double impact on NO removal. CO 2 concentration has no obvious effect on NO removal. and produced from VUV-activation of PMS play a leading role in NO removal. O 3 and ·O produced from VUV-activation of O 2 also play an important role in NO removal. SO 2 achieves complete removal under all experimental conditions due to its very high solubility in water and good reactivity. The highest simultaneous removal efficiency of SO 2 and NO reaches 100% and 91.3%, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

The effect of high intensity mixing on the enzymatic hydrolysis of concentrated cellulose fiber suspensions

Treesearch

Joseph R. Samaniuk; C. Tim Scott; Thatcher W. Root; Daniel J. Klingenberg

2011-01-01

Enzymatic hydrolysis of lignocellulosic biomass in a high shear environment was examined. The conversion of cellulose to glucose in samples mixed in a torque rheometer producing shear flows similar to those found in twin screw extruders was greater than that of unmixed samples. In addition, there is a synergistic effect of mixing and enzymatic hydrolysis; mixing...

Photooxidation of chloride by oxide minerals: implications for perchlorate on Mars.

PubMed

Schuttlefield, Jennifer D; Sambur, Justin B; Gelwicks, Melissa; Eggleston, Carrick M; Parkinson, B A

2011-11-09

We show that highly oxidizing valence band holes, produced by ultraviolet (UV) illumination of naturally occurring semiconducting minerals, are capable of oxidizing chloride ion to perchlorate in aqueous solutions at higher rates than other known natural perchlorate production processes. Our results support an alternative to atmospheric reactions leading to the formation of high concentrations of perchlorate on Mars.

Effect of quinine on the release of catecholamines from bovine cultured chromaffin cells.

PubMed Central

Tang, R.; Novas, M. L.; Glavinovic, M. I.; Trifaró, J. M.

1990-01-01

1. The effects of quinine on catecholamine release from cultured bovine chromaffin cells were studied. 2. Quinine (25-400 microM) produced a dose-related inhibition of catecholamine release in response to depolarizing concentrations (12.5-50 mM) of K+. 3. The inhibition of the secretory response to high K+ produced by quinine decreased with the increase in the extracellular concentration of Ca2+. 4. Stimulation of cultured chromaffin cells with 50 mM K+ produced a significant increase in Ca2+ influx. In the presence of 100 microM quinine a 54% inhibition of the K(+)-induced Ca2+ influx was observed. 5. Quinine treatment of chromaffin cell cultures produced a small but significant decrease in membrane resting potential and a less pronounced depolarization in response to 50 mM K+. 6. The results suggest that the inhibition of the K(+)-evoked release of catecholamines produced by quinine is at least partly due to a decrease in Ca2+ influx. Ca2+ influx is lower because quinine reduces the sensitivity of the membrane potential to changes in extracellular K+ but direct effects of quinine on Ca2+ channels cannot be excluded. PMID:2158846

Evaluation of the calcium-antagonist, antidiarrhoeic and central nervous system activities of Baccharis serraefolia.

PubMed

Tortoriello, J; Aguilar-Santamaría, L

1996-09-01

Baccharis serraefolia is a widely used plant to treat diarrhoea in Mexican traditional medicine. Although the methanolic extract of this plant has shown an important dose-dependent spasmolytic activity, its underlying mechanism has not been studied. In the present work, the methanolic extract of B. serraefolia significantly delayed the onset of tonic seizures induced by strychnine and pentylenetetrazol; besides, it diminished the death rate and number of animals that exhibited convulsions. It produced potentiation of the hypnotic effect of pentobarbital. Oral administration produced an inhibition of gastrointestinal transit in mice as effective as that produced by loperamide. As to the effect on smooth muscles, the active extract produced an inhibition of contraction induced electrically, which could not be reversed by naloxone. The calcium concentration-contraction curve showed a rightward displacement when the extract was added to isolated guinea pig ileum depolarized with high K+ and cumulative concentrations of Ca2+. The results suggest that the methanolic extract does not interact with classical opiate receptors and its effects, at least that produced on smooth muscle, may be due to a probable interference with calcium influx and/or calcium release from an intra-cellular store.

Method of particle trajectory recognition in particle flows of high particle concentration using a candidate trajectory tree process with variable search areas

DOEpatents

Shaffer, Franklin D.

2013-03-12

The application relates to particle trajectory recognition from a Centroid Population comprised of Centroids having an (x, y, t) or (x, y, f) coordinate. The method is applicable to visualization and measurement of particle flow fields of high particle. In one embodiment, the centroids are generated from particle images recorded on camera frames. The application encompasses digital computer systems and distribution mediums implementing the method disclosed and is particularly applicable to recognizing trajectories of particles in particle flows of high particle concentration. The method accomplishes trajectory recognition by forming Candidate Trajectory Trees and repeated searches at varying Search Velocities, such that initial search areas are set to a minimum size in order to recognize only the slowest, least accelerating particles which produce higher local concentrations. When a trajectory is recognized, the centroids in that trajectory are removed from consideration in future searches.

Degradation of cyanotoxins (microcystin) in drinking water using photoelectrooxidation.

PubMed

Garcia, A C A; Rodrigues, M A S; Xavier, J L N; Gazulla, V; Meneguzzi, A; Bernardes, A M

2015-05-01

The discharge of sewage and industrial effluents containing high concentrations of pollutants in water bodies increases eutrophication. Cyanobacteria, some of the organisms whose growth is promoted by high nutrient concentrations, are resistant and produce several types of toxins, known as cyanotoxins, highly harmful to human beings. Current water treatment systems for the public water supply are not efficient in degradation of toxins. Advanced oxidation processes (AOP) have been tested for the removal of cyanotoxins, and the results have been positive. This study examines the application of photoelectrooxidation in the degradation of cyanotoxins (microcystins). The performance of the oxidative processes involved was evaluated separately: Photocatalysis, Electrolysis and Photoelectrooxidation. Results showed that the electrical current and UV radiation were directly associated with toxin degradation. The PEO system is efficient in removing cyanotoxins, and the reduction rate reached 99%. The final concentration of toxin was less than 1 µg/L of microcystin in the treated solution.

Biosurfactant Production by Bacillus salmalaya for Lubricating Oil Solubilization and Biodegradation.

PubMed

Dadrasnia, Arezoo; Ismail, Salmah

2015-08-19

This study investigated the capability of a biosurfactant produced by a novel strain of Bacillus salmalaya to enhance the biodegradation rates and bioavailability of organic contaminants. The biosurfactant produced by cultured strain 139SI showed high physicochemical properties and surface activity in the selected medium. The biosurfactant exhibited a high emulsification index and a positive result in the drop collapse test, with the results demonstrating the wetting activity of the biosurfactant and its potential to produce surface-active molecules. Strain 139SI can significantly reduce the surface tension (ST) from 70.5 to 27 mN/m, with a critical micelle concentration of 0.4%. Moreover, lubricating oil at 2% (v/v) was degraded on Day 20 (71.5). Furthermore, the biosurfactant demonstrated high stability at different ranges of salinity, pH, and temperature. Overall, the results indicated the potential use of B. salmalaya 139SI in environmental remediation processes.

Inhibition of Coenzyme Qs Accumulation in Engineered Escherichia coli by High Concentration of Farnesyl Diphosphate.

PubMed

Samoudi, Mojtaba; Omid Yeganeh, Negar; Shahbani Zahiri, Hossein; Shariati, Parvin; Hajhosseini, Reza

2015-01-01

Coenzyme Q 10 (CoQ 10 ) is an isoprenoid component used widely in nutraceutical industries. Farnesyl diphosphate synthase (FPPS) is a responsible enzyme for biosynthesis of farnesyl diphosphate (FPP), a key precursor for CoQs production. This research involved investigating the effect of FPPS over-expression on CoQs production in engineered CoQ 10 -producing Escherichia coli (E. coli). Two CoQ 10 -producing strains, as referred to E. coli Ba and E. coli Br, were transformed by the encoding gene for FPPS (ispA) under the control of either the trc or P BAD promoters. Over-expression of ispA under the control of P BAD promoter led to a relative increase in CoQ 10 production only in recombinant E. coli Br although induction by arabinose resulted in partial reduction of CoQ 10 production in both recombinant E. coli Ba and E. coli Br strains. Over-expression of ispA under the control of stronger trc promoter, however, led to a severe decrease in CoQ 10 production in both recombinant E. coli Ba and E. coli Br strains, as reflected by reductions from 629±40 to 30±13 and 564±28 to 80±14 μg/g Dried Cell Weight (DCW), respectively. The results showed high level of FPP reduces endogenous CoQ 8 production as well and that CoQs are produced in a complimentary manner, as the increase in production of one decreases the production of the other. The reduction in CoQ 10 production can be a result of Dds inhibition by high FPP concentration. Therefore, more effort is needed to verify the role of intermediate metabolite concentration and to optimize production of CoQ 10 .

Inhibition of Coenzyme Qs Accumulation in Engineered Escherichia coli by High Concentration of Farnesyl Diphosphate

PubMed Central

Samoudi, Mojtaba; Omid Yeganeh, Negar; Shahbani Zahiri, Hossein; Shariati, Parvin; Hajhosseini, Reza

2015-01-01

Background: Coenzyme Q 10 (CoQ 10 ) is an isoprenoid component used widely in nutraceutical industries. Farnesyl diphosphate synthase (FPPS) is a responsible enzyme for biosynthesis of farnesyl diphosphate (FPP), a key precursor for CoQs production. This research involved investigating the effect of FPPS over-expression on CoQs production in engineered CoQ 10 -producing Escherichia coli (E. coli). Methods: Two CoQ 10 -producing strains, as referred to E. coli Ba and E. coli Br, were transformed by the encoding gene for FPPS (ispA) under the control of either the trc or P BAD promoters. Results: Over-expression of ispA under the control of P BAD promoter led to a relative increase in CoQ 10 production only in recombinant E. coli Br although induction by arabinose resulted in partial reduction of CoQ 10 production in both recombinant E. coli Ba and E. coli Br strains. Over-expression of ispA under the control of stronger trc promoter, however, led to a severe decrease in CoQ 10 production in both recombinant E. coli Ba and E. coli Br strains, as reflected by reductions from 629±40 to 30±13 and 564±28 to 80±14 μg/g Dried Cell Weight (DCW), respectively. The results showed high level of FPP reduces endogenous CoQ 8 production as well and that CoQs are produced in a complimentary manner, as the increase in production of one decreases the production of the other. Conclusion: The reduction in CoQ 10 production can be a result of Dds inhibition by high FPP concentration. Therefore, more effort is needed to verify the role of intermediate metabolite concentration and to optimize production of CoQ 10 . PMID:26306151

Elucidating the role of the phenylacetic acid metabolic complex in the pathogenic activity of Rhizoctonia solani anastomosis group 3.

PubMed

Bartz, Faith E; Glassbrook, Norman J; Danehower, David A; Cubeta, Marc A

2012-01-01

The soil fungus Rhizoctonia solani produces phytotoxic phenylacetic acid (PAA) and hydroxy (OH-) and methoxy (MeO-) derivatives of PAA. However, limited information is available on the specific role that these compounds play in the development of Rhizoctonia disease symptoms and concentration(s) required to induce a host response. Reports that PAA inhibits the growth of R. solani conflict with the established ability of the fungus to produce and metabolize PAA. Experiments were conducted to clarify the role of the PAA metabolic complex in Rhizoctonia disease. In this study the concentration of PAA and derivatives required to induce tomato root necrosis and stem canker, in the absence of the fungus, and the concentration that inhibits mycelial growth of R. solani were determined. The effect of exogenous PAA and derivatives of PAA on tomato seedling growth also was investigated. Growth of tomato seedlings in medium containing 0.1-7.5 mM PAA and derivatives induced necrosis of up to 85% of root system. Canker development resulted from injection of tomato seedling stems with 7.5 mM PAA, 3-OH-PAA, or 3-MeO-PAA. PAA in the growth medium reduced R. solani biomass, with 50% reduction observed at 7.5 mM. PAA, and derivatives were quantified from the culture medium of 14 isolates of R. solani belonging to three distinct anastomosis groups by GC-MS. The quantities ranged from below the limit of detection to 678 nM, below the concentrations experimentally determined to be phytotoxic. Correlation analyses revealed that isolates of R. solani that produced high PAA and derivatives in vitro also caused high mortality on tomato seedlings. The results of this investigation add to the body of evidence that the PAA metabolic complex is involved in Rhizoctonia disease development but do not indicate that production of these compounds is the primary or the only determinant of pathogenicity.

Economic considerations of battery recycling based on the Recytec process

NASA Astrophysics Data System (ADS)

Ammann, Pierre

The Recytec process is successfully operated on a continuous industrial base since autumn 1994. All the products are regularly re-used without any problems and environmental limits are fully respected. The European Community Battery Directive is valid since many years and only a few countries like Switzerland and The Netherlands have implemented it in national guidelines. In the meantime, battery producers have accepted the necessity of the recycling of mercury-free batteries in order to prevent the contamination of municipal waste streams by other heavy metals, such as zinc and cadmium. Recycling processes like the Recytec process are considered by the battery producers as highly expensive and they are looking for cheaper alternatives. Steel works are confronted with a market change and have to produce less quantities of better quality steels with more stringent environmental limits. The electric arc furnace (EAF), one of the chosen battery destruction techniques, is producing 20% of the European steel. Even if the battery mixes contain only mercury-free batteries, the residual mercury content and the zinc concentration will be too high to insure a good steel quality, if all collected batteries will be fed in EAF. In Waelz kilns (production of zinc oxide concentrates for zinc producers) the situation is the same with regard to the residual mercury concentration and environmental limits. Sorting technologies for the separation of battery mixes into the different battery chemistries will presently fail because the re-users of these sorted mercury-free batteries are not able to accept raw waste batteries but they are interested in some fractions of them. This means that in any case pretreatment is an unavoidable step before selective reclamation of waste batteries. The Recytec process is the low-cost partner in a global strategy for battery recycling. This process is very flexible and will be able to follow, with slight and inexpensive adaptations of the equipment, the trend in mercury content and quantities of collected batteries.

Influence of process changes on PCDD/Fs produced in an iron ore sintering plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guerriero, E.; Bianchini, M.; Gigliucci, P.F.

2009-01-15

This study investigated the influence of different charge typologies and additives on the PCDD/Fs amount produced and on the congener profiles in an iron ore sintering plant. Many tests were carried out combining different typologies of charge (iron materials) and solid fuel ('coke breeze' or 'anthracite') with or without the use of urea. The PCDD/Fs produced ranged from 1.2 to 22.7 {mu} g I-TEQ/ton of agglomerate, whereas the PCDD/Fs released to the ambient air ranged from 0.10 to 1.92 ng I-TEQ/Nm{sup 3} because of cleaning in an electrostatic precipitator (ESP) and a Wetfine scrubber (WS). A more homogeneous charge withmore » a higher amount of fine particles charge appeared to produce a lower PCDD/Fs concentration due to a better combustion but this hypothesis needs further investigations on charges having different dimension particles. Only a synergitic action of urea and anthracite was able to reduce the high PCDD/Fs content due to the bad combustion of the more inhomogeneous charge with a lower amount of fine particles. The congener profile was a typical combustion process fingerprint because the PCDFs predominated, the highly chlorinated congeners (HeptaCDD and OctaCDD) prevailed in PCDDs, whereas in PCDFs the profile was more varied; 1,2,3,4,6,7,8-HeptaCDF was the main contributor to the total concentration while 2,3,4,7,8-PentaCDF was the main contributor to the I-TEQ concentration. Whereas all the parameters under scrutiny influenced strongly the amount of PCDD/Fs produced, they affected only slightly the fingerprint of PCDD/Fs. In all cases studied, the reduction obtained using urea, anthracite, or the more homogeneous charge with a higher amount of fine particles was slightly greater on the higher chlorinated congeners in respect to the lower ones.« less

Ex Vivo Pharmacodynamics of Amoxicillin-Clavulanate against β-Lactamase-Producing Escherichia coli in a Yucatan Miniature Pig Model That Mimics Human Pharmacokinetics

PubMed Central

Bronner, Stéphane; Murbach, Valérie; Peter, Jean-Daniel; Levêque, Dominique; Elkhaïli, Hassan; Salmon, Yves; Dhoyen, Nathalie; Monteil, Henri; Woodnutt, Gary; Jehl, François

2002-01-01

The objective of the present study was to investigate the potential bactericidal activity of amoxicillin-clavulanate against β-lactamase-producing Escherichia coli strains and to elucidate the extent to which enzyme production affects the activity. Six adult Yucatan miniature pigs received a single intravenous dose of 1.1 g of amoxicillin-clavulanate as an intravenous infusion over 30 min. The pharmacokinetic parameters were determined for the serum samples and compared to the published data for humans (2.2-g intravenous dose). The parameters were comparable for the two species, and therefore, the miniature pig constitutes a good model for pharmacodynamic study of amoxicillin-clavulanate. Therefore, the model was used in an ex vivo pharmacodynamic study of amoxicillin-clavulanate against four strains of Escherichia coli producing β-lactamases at different levels. The E. coli strains were cultured with serial dilutions (1:2 to 1:256) of the serum samples from the pharmacokinetic study, and the number of surviving bacteria was determined after 1, 3, and 6 h of exposure. Amoxicillin-clavulanate at concentrations less than the MIC and the minimal bactericidal concentration had marked bactericidal potency against the strain that produced low levels of penicillinase. For high-level or intermediate-level β-lactamase-producing strains, the existence of a clavulanate concentration threshold of 1.5 to 2 μg/ml, below which there was no bactericidal activity, was demonstrated. The index of surviving bacteria showed the existence of mixed concentration- and time-dependent actions of amoxicillin (in the presence of clavulanate) which varied as a function of the magnitude of β-lactamase production by the test strains. This study shows the effectiveness of amoxicillin-clavulanate against low- and intermediate-level penicillinase-producing strains of E. coli. These findings are to be confirmed in a miniature pig experimental infection model. PMID:12435677

Elastic Stability of Concentric Tube Robots: A Stability Measure and Design Test

PubMed Central

Gilbert, Hunter B.; Hendrick, Richard J.; Webster, Robert J.

2016-01-01

Concentric tube robots are needle-sized manipulators which have been investigated for use in minimally invasive surgeries. It was noted early in the development of these devices that elastic energy storage can lead to rapid snapping motion for designs with moderate to high tube curvatures. Substantial progress has recently been made in the concentric tube robot community in designing snap-free robots, planning stable paths, and characterizing conditions that result in snapping for specific classes of concentric tube robots. However, a general measure for how stable a given robot configuration is has yet to be proposed. In this paper, we use bifurcation and elastic stability theory to provide such a measure, as well as to produce a test for determining whether a given design is snap-free (i.e. whether snapping can occur anywhere in the unloaded robot’s workspace). These results are useful in designing, planning motions for, and controlling concentric tube robots with high curvatures. PMID:27042170

Homogeneous Aerosol Freezing in the Tops of High-Altitude Tropical Cumulonimbus Clouds

NASA Technical Reports Server (NTRS)

Jensen, E. J.; Ackerman, A. S.

2006-01-01

Numerical simulations of deep, intense continental tropical convection indicate that when the cloud tops extend more than a few kilometers above the liquid water homogeneous freezing level, ice nucleation due to freezing of entrained aqueous sulfate aerosols generates large concentrations of small crystals (diameters less than approx. equal to 20 micrometers). The small crystals produced by aerosol freezing have the largest impact on cloud-top ice concentration for convective clouds with strong updrafts but relatively low aerosol concentrations. An implication of this result is that cloud-top ice concentrations in high anvil cirrus can be controlled primarily by updraft speeds in the tops of convective plumes and to a lesser extent by aerosol concentrations in the uppermost troposphere. While larger crystals precipitate out and sublimate in subsaturated air below, the population of small crystals can persist in the saturated uppermost troposphere for many hours, thereby prolonging the lifetime of remnants from anvil cirrus in the tropical tropopause layer.

Elastic Stability of Concentric Tube Robots: A Stability Measure and Design Test.

PubMed

Gilbert, Hunter B; Hendrick, Richard J; Webster, Robert J

2016-02-01

Concentric tube robots are needle-sized manipulators which have been investigated for use in minimally invasive surgeries. It was noted early in the development of these devices that elastic energy storage can lead to rapid snapping motion for designs with moderate to high tube curvatures. Substantial progress has recently been made in the concentric tube robot community in designing snap-free robots, planning stable paths, and characterizing conditions that result in snapping for specific classes of concentric tube robots. However, a general measure for how stable a given robot configuration is has yet to be proposed. In this paper, we use bifurcation and elastic stability theory to provide such a measure, as well as to produce a test for determining whether a given design is snap-free (i.e. whether snapping can occur anywhere in the unloaded robot's workspace). These results are useful in designing, planning motions for, and controlling concentric tube robots with high curvatures.

Poor fluorinated graphene sheets carboxymethylcellulose polymer composite mode locker for erbium doped fiber laser

NASA Astrophysics Data System (ADS)

Mou, Chengbo; Arif, Raz; Lobach, Anatoly S.; Khudyakov, Dmitry V.; Spitsina, Nataliya G.; Kazakov, Valery A.; Turitsyn, Sergei; Rozhin, Aleksey

2015-02-01

We report poor fluorinated graphene sheets produced by thermal exfoliation embedding in carboxymethylcellulose polymer composite (GCMC) as an efficient mode locker for erbium doped fiber laser. Two GCMC mode lockers with different concentration have been fabricated. The GCMC based mode locked fiber laser shows stable soliton output pulse shaping with repetition rate of 28.5 MHz and output power of 5.5 mW was achieved with the high concentration GCMC, while a slightly higher output power of 6.9 mW was obtained using the low concentration GCMC mode locker.

Poor fluorinated graphene sheets carboxymethylcellulose polymer composite mode locker for erbium doped fiber laser

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mou, Chengbo, E-mail: mouc1@aston.ac.uk, E-mail: a.rozhin@aston.ac.uk; Turitsyn, Sergei; Rozhin, Aleksey, E-mail: mouc1@aston.ac.uk, E-mail: a.rozhin@aston.ac.uk

We report poor fluorinated graphene sheets produced by thermal exfoliation embedding in carboxymethylcellulose polymer composite (GCMC) as an efficient mode locker for erbium doped fiber laser. Two GCMC mode lockers with different concentration have been fabricated. The GCMC based mode locked fiber laser shows stable soliton output pulse shaping with repetition rate of 28.5 MHz and output power of 5.5 mW was achieved with the high concentration GCMC, while a slightly higher output power of 6.9 mW was obtained using the low concentration GCMC mode locker.

Spray dried microparticles of chia oil using emulsion stabilized by whey protein concentrate and pectin by electrostatic deposition.

PubMed

Noello, C; Carvalho, A G S; Silva, V M; Hubinger, M D

2016-11-01

Chia seed oil has a high content of α-linolenic acid (60%) and linoleic acid (20%). Use of this oil in different products is limited due to its liquid state, and the presence of insaturation is a trigger for oxidation. In this context, to facilitate the incorporation of chia oil in food products and increase its protection against oxidation, the aim of this work was to produce chia oil microparticles by spray drying using emulsions stabilized by whey protein concentrate (ζ-potential +13.4 at pH3.8) and pectin (ζ-potential -40.4 at pH3.8) through the electrostatic layer-by-layer deposition technique and emulsions prepared with only whey protein concentrate. Emulsions stabilized by whey protein concentrate and stabilized by whey protein concentrate-pectin were prepared using maltodextrin (10 DE) and modified starch (Hi-Cap® 100). They were characterized in relation to stability, droplet size, ζ-Potential and optical microscopy. The microparticles were characterized in relation to moisture content, water activity, particle size, microstructure and oxidative stability by the Rancimat method. Emulsions stabilized by whey protein concentrate-pectin with added maltodextrin 10 DE and emulsions stabilized by whey protein concentrate with added modified starch (Hi-Cap® 100) were stable after 24h. Emulsions stabilized by whey protein concentrate and by whey protein concentrate-pectin showed droplets with mean diameter ranging from 0.80 to 1.31μm, respectively and ζ-potential varying from -6.9 to -27.43mV, respectively. After spray drying, the microparticles showed an mean diameter ranging from 7.00 to 9.00μm. All samples presented high encapsulation efficiency values, above 99%. Microparticles produced with modified starch showed a smoother spherical surface than particles with maltodextrin 10 DE, which presented a wrinkled surface. All microparticles exhibited higher oxidative stability than chia oil in pure form. Copyright © 2016 Elsevier Ltd. All rights reserved.

Heavy metals in produce from urban farms in the San Francisco Bay Area.

PubMed

Kohrman, Hannah; Chamberlain, C Page

2014-01-01

Cadmium (Cd) and lead (Pb) concentrations were analysed in 96 samples of produce from seven urban farms, three suburban farms and three grocery stores in the San Francisco Bay Area in 2011-2012. Cd concentrations were highest in urban chard (0.043 mg kg(-1)) and lowest in urban, suburban and grocery squash (0.003 mg kg(-1)). Pb concentrations were highest in urban kale (0.080 mg kg(-1)) and lowest in grocery squash (0.008 mg kg(-1)). The mean heavy metal concentrations for Cd and Pb in all produce types were well below the maximum limits as set by the Food and Agriculture Organization (FAO) and the World Health Organization (WHO). Individual concentrations of Cd and Pb were below the limits of detection in 26 of 192 analyses. Cd and Pb concentrations in produce from urban farms were not significantly different from produce grown in suburban farms or grocery stores. It was concluded that produce from urban community farms in San Francisco, at least for the farms studied, is safe for human consumption.

Atmospheric conditions during high ragweed pollen concentrations in Zagreb, Croatia.

PubMed

Prtenjak, Maja Telišman; Srnec, Lidija; Peternel, Renata; Madžarević, Valentina; Hrga, Ivana; Stjepanović, Barbara

2012-11-01

We examined the atmospheric conditions favourable to the occurrence of maximum concentrations of ragweed pollen with an extremely high risk of producing allergy. Over the 2002-2009 period, daily pollen data collected in Zagreb were used to identify two periods of high pollen concentration (> 600 grains/m(3)) for our analysis: period A (3-4 September 2002) and period B (6-7 September 2003). Synoptic conditions in both periods were very similar: Croatia was under the influence of a lower sector high pressure system moving slowly eastward over Eastern Europe. During the 2002-2009 period, this type of weather pattern (on ~ 70% of days), in conjunction with almost non-gradient surface pressure conditions in the area (on ~ 30% of days) characterised days when the daily pollen concentrations were higher than 400 grains/m(3). Numerical experiments using a mesoscale model at fine resolution showed successful multi-day simulations reproducing the local topographic influence on wind flow and in reasonable agreement with available observations. According to the model, the relatively weak synoptic flow (predominantly from the eastern direction) allowed local thermal circulations to develop over Zagreb during both high pollen episodes. Two-hour pollen concentrations and 48-h back-trajectories indicated that regional-range transport of pollen grains from the central Pannonian Plain was the cause of the high pollen concentrations during period A. During period B, the north-westward regional-range transport in Zagreb was supplemented significantly by pronounced horizontal recirculation of pollen grains. This recirculation happened within the diurnal local circulation over the city, causing a late-evening increase in pollen concentration.

Atmospheric conditions during high ragweed pollen concentrations in Zagreb, Croatia

NASA Astrophysics Data System (ADS)

Prtenjak, Maja Telišman; Srnec, Lidija; Peternel, Renata; Madžarević, Valentina; Hrga, Ivana; Stjepanović, Barbara

2012-11-01

We examined the atmospheric conditions favourable to the occurrence of maximum concentrations of ragweed pollen with an extremely high risk of producing allergy. Over the 2002-2009 period, daily pollen data collected in Zagreb were used to identify two periods of high pollen concentration (> 600 grains/m3) for our analysis: period A (3-4 September 2002) and period B (6-7 September 2003). Synoptic conditions in both periods were very similar: Croatia was under the influence of a lower sector high pressure system moving slowly eastward over Eastern Europe. During the 2002-2009 period, this type of weather pattern (on ~ 70% of days), in conjunction with almost non-gradient surface pressure conditions in the area (on ~ 30% of days) characterised days when the daily pollen concentrations were higher than 400 grains/m3. Numerical experiments using a mesoscale model at fine resolution showed successful multi-day simulations reproducing the local topographic influence on wind flow and in reasonable agreement with available observations. According to the model, the relatively weak synoptic flow (predominantly from the eastern direction) allowed local thermal circulations to develop over Zagreb during both high pollen episodes. Two-hour pollen concentrations and 48-h back-trajectories indicated that regional-range transport of pollen grains from the central Pannonian Plain was the cause of the high pollen concentrations during period A. During period B, the north-westward regional-range transport in Zagreb was supplemented significantly by pronounced horizontal recirculation of pollen grains. This recirculation happened within the diurnal local circulation over the city, causing a late-evening increase in pollen concentration.

DMR (deacetylation and mechanical refining) processing of corn stover achieves high monomeric sugar concentrations (230 g L -1) during enzymatic hydrolysis and high ethanol concentrations (>10% v/v) during fermentation without hydrolysate purification or concentration

DOE PAGES

Chen, Xiaowen; Kuhn, Erik; Jennings, Edward W.; ...

2016-04-01

Distilling and purifying ethanol and other products from second generation lignocellulosic biorefineries adds significant capital and operating costs to biofuel production. The energy usage associated with distillation negatively affects plant gate costs and causes environmental and life-cycle impacts, and the lower titers in fermentation caused by lower sugar concentrations from pretreatment and enzymatic hydrolysis increase energy and water usage and ethanol production costs. In addition, lower ethanol titers increase the volumes required for enzymatic hydrolysis and fermentation vessels increase capital expenditure (CAPEX). Therefore, increasing biofuel titers has been a research focus in renewable biofuel production for several decades. In thismore » work, we achieved approximately 230 g L -1 of monomeric sugars after high solid enzymatic hydrolysis using deacetylation and mechanical refining (DMR) processed corn stover substrates produced at the 100 kg per day scale. The high sugar concentrations and low chemical inhibitor concentrations achieved by the DMR process allowed fermentation to ethanol with titers as high as 86 g L -1, which translates into approximately 10.9% v/v ethanol. To our knowledge, this is the first time that titers greater than 10% v/v ethanol in fermentations derived from corn stover without any sugar concentration or purification steps have been reported. As a result, the potential cost savings from high sugar and ethanol titers achieved by the DMR process are also reported using TEA analysis.« less

DMR (deacetylation and mechanical refining) processing of corn stover achieves high monomeric sugar concentrations (230 g L -1) during enzymatic hydrolysis and high ethanol concentrations (>10% v/v) during fermentation without hydrolysate purification or concentration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Xiaowen; Kuhn, Erik; Jennings, Edward W.

Distilling and purifying ethanol and other products from second generation lignocellulosic biorefineries adds significant capital and operating costs to biofuel production. The energy usage associated with distillation negatively affects plant gate costs and causes environmental and life-cycle impacts, and the lower titers in fermentation caused by lower sugar concentrations from pretreatment and enzymatic hydrolysis increase energy and water usage and ethanol production costs. In addition, lower ethanol titers increase the volumes required for enzymatic hydrolysis and fermentation vessels increase capital expenditure (CAPEX). Therefore, increasing biofuel titers has been a research focus in renewable biofuel production for several decades. In thismore » work, we achieved approximately 230 g L -1 of monomeric sugars after high solid enzymatic hydrolysis using deacetylation and mechanical refining (DMR) processed corn stover substrates produced at the 100 kg per day scale. The high sugar concentrations and low chemical inhibitor concentrations achieved by the DMR process allowed fermentation to ethanol with titers as high as 86 g L -1, which translates into approximately 10.9% v/v ethanol. To our knowledge, this is the first time that titers greater than 10% v/v ethanol in fermentations derived from corn stover without any sugar concentration or purification steps have been reported. As a result, the potential cost savings from high sugar and ethanol titers achieved by the DMR process are also reported using TEA analysis.« less

Studies on antioxidative enzymes induced by cadmium in pea plants (Pisum sativum).

PubMed

Pandey, Nalini; Singh, Gaurav Kumar

2012-03-01

Pea plants (Pisum sativum cv. Swati) exposed to different concentration of cadmium (50,100, 200 microM Cd) under controlled glass house conditions were quantified for different physiological parameters and antioxidative enzymes. In pea plants, Cd produced a significant inhibition of growth and induced chlorosis, marginal yellowing and necrosis in young leaves, the effect being most pronounced at 200 microM Cd supply. An alteration in the activated oxygen metabolism of pea plants were also detected as evidenced by an increase in concentration of H2O2 and TBARS along with decrease in the chlorophyll and carotenoid concentration in leaves. Cadmium toxicity induced an increase in non-protein thiol, ascorbate, proline and cysteine concentration. A significant increment in the activity of SOD, APX and GR, and a decrease in CAT was observed as a result of Cd treatment. The enhanced activity of SOD and inhibition of CAT and POD produces a high build up of H2O2 which appears to be the main cause of oxidative stress due to Cd toxicity in pea plants.

Origin of the selectivity in the gold-mediated oxidation of benzyl alcohol

NASA Astrophysics Data System (ADS)

Rodríguez-Reyes, Juan Carlos F.; Friend, Cynthia M.; Madix, Robert J.

2012-08-01

Benzyl alcohol has received substantial attention as a probe molecule to test the selectivity and efficiency of novel metallic gold catalysts. Herein, the mechanisms of benzyl alcohol oxidation on a gold surface covered with atomic oxygen are elucidated; the results show direct correspondence to the reaction on gold-based catalysts. The selective, partial oxidation of benzyl alcohol to benzaldehyde is achieved with low oxygen surface concentrations and takes place through dehydrogenation of the alcohol to form benzaldehyde via a benzyloxy (C6H5-CH2O) intermediate. While in this case atomic oxygen plays solely a dehydrogenating role, at higher concentrations it leads to the formation of intermediates from benzaldehyde, producing benzoic acid and CO2. Facile ester (benzyl benzoate) formation also occurs at low oxygen concentrations, which indicates that benzoic acid is not a precursor of further oxidation of the ester; instead, the ester is produced by the coupling of adsorbed benzyloxy and benzaldehyde. Key to the high selectivity seen at low oxygen concentrations is the fact that the production of the aldehyde (and esters) is kinetically favored over the production of benzoic acid.

Neuropeptide Y in phaeochromocytomas and ganglioneuroblastomas.

PubMed

Adrian, T E; Allen, J M; Terenghi, G; Bacarese-Hamilton, A J; Brown, M J; Polak, J M; Bloom, S R

1983-09-03

Tumour tissue from nineteen patients with phaeochromocytomas and nine with ganglioneuroblastomas contained large numbers of neuropeptide Y (NPY) producing cells and extracts of these tumours had very high concentrations of immunoreactive NPY. Plasma NPY concentrations were also raised, averaging 460 pmol/l in patients with tumours of the sympathetic chain and 55 pmol/l in healthy controls. Since plasma NPY is straightforward to measure and relatively stable, its estimation may prove helpful as a screening tests for phaeochromocytoma.

Isolation and Characterization of Saponin-Producing Fungal Endophytes from Aralia elata in Northeast China

PubMed Central

Wu, Hao; Yang, Hongyan; You, Xiangling; Li, Yuhua

2012-01-01

The purpose of this study was to investigate the diversity of endophytic fungi of Aralia elata distributed in Northeast China as well as their capacity to produce saponins. Ninety-six strains of endophytic fungi were isolated, and polymerase chain reaction (PCR) and sequencing were employed to identify the isolates. The saponin concentrations of the culture filtrates of representative strains were measured. The agar diffusion method was used to test antimicrobial activity, while high-performance liquid chromatography (HPLC) was employed to identify the saponins produced by representative strains. Alternaria, Botryosphaeria, Camarosporium, Cryptosporiopsis, Diaporthe, Dictyochaeta, Penicillium, Fusarium, Nectria, Peniophora, Schizophyllum, Cladosporium and Trichoderma species were isolated in this study. Overall, 25% of the isolates belonged to Diaporthe (Diaporthe eres), and 12.5% belonged to Alternaria. The highest concentration of saponins was produced by G22 (2.049 mg/mL). According to the results of the phylogenetic analysis, G22 belonged to the genus Penicillium. The culture filtrate of G22 exhibited antibacterial activity against Staphylococcus aureus, and ginsenosides Re and Rb2 were detected in G22 culture filtrates by HPLC. PMID:23203194

Advanced Water Purification System for In Situ Resource Utilization

NASA Technical Reports Server (NTRS)

Anthony, Stephen M.; Jolley, Scott T.; Captain, James G.

2013-01-01

A main goal in the field of In Situ Resource Utilization is to develop technologies that produce oxygen from regolith to provide consumables to an extraterrestrial outpost. The processes developed reduce metal oxides in the regolith to produce water, which is then electrolyzed to produce oxygen. Hydrochloric and hydrofluoric acids are byproducts of the reduction processes, which must be removed to meet electrolysis purity standards. We previously characterized Nation, a highly water selective polymeric proton-exchange membrane, as a filtration material to recover pure water from the contaminated solution. While the membranes successfully removed both acid contaminants, the removal efficiency of and water flow rate through the membranes were not sufficient to produce large volumes of electrolysis-grade water. In the present study, we investigated electrodialysis as a potential acid removal technique. Our studies have shown a rapid and significant reduction in chloride and fluoride concentrations in the feed solution, while generating a relatively small volume of concentrated waste water. Electrodialysis has shown significant promise as the primary separation technique in ISRU water purification processes.

Advanced Water Purification System for In Situ Resource Utilization Project

NASA Technical Reports Server (NTRS)

Anthony, Stephen M.

2014-01-01

A main goal in the field of In Situ Resource Utilization is to develop technologies that produce oxygen from regolith to provide consumables to an extratrrestrial outpost. The processes developed reduce metal oxides in the regolith to produce water, which is then electrolyzed to produce oxygen. Hydrochloric and hydrofluoric acids are byproducts of the reduction processes, which must be removed to meet electrolysis purity standards. We previously characterized Nation, a highly water selective polymeric proton-exchange membrane, as a filtrtion material to recover pure water from the contaminated solution. While the membranes successfully removed both acid contaminants, the removal efficiency of and water flow rate through the membranes were not sufficient to produce large volumes of electrolysis-grade water. In the present study, we investigated electrodialysis as a potential acid removable technique. Our studies have show a rapid and significant reduction in chloride and fluoride concentrations in the feed solution, while generating a relatively small volume of concentrated waste water. Electrodialysis has shown significant promise as the primary separation technique in ISRU water purification processes.

Controlling Pu behavior on Titania: Implications for LEU Fission-Based Mo-99 Production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Youker, Amanda J.; Brown, M. Alex; Heltemes, Thad A.

Molybdenum-99 is the parent isotope of the most widely used isotope, technetium-99m, in all diagnostic nuclear medicine procedures. Due to proliferation concerns associated with the use of highly enriched uranium (HEU), the preferred method of fission-based Mo-99 production uses low enriched uranium (LEU) targets. Using LEU versus HEU for Mo-99 production produces similar to 30 times more Pu-239, due to neutron capture on U-238 to produce Np-239, which ultimately decays to Pu-239 (t(1/2) = 24,110 yr). Argonne National Laboratory is supporting a potential US Mo-99 producer in their efforts to produce Mo-99 from an LEU solution. In order to mitigatemore » the generation of large volumes of greater-than-class-C (GTCC) low level waste (Pu-239 concentrations greater than 1 nCi/g), we have focused our efforts on the separation chemistry of Pu and Mo with a titania sorbent in sulfate media. Results from batch and column experiments show that temperature and acid wash concentration can be used to control Pu behavior on titania.« less

Production of Chitosan from Amusium sp Scallop Shell Waste

NASA Astrophysics Data System (ADS)

Rokhati, Nur; Istirokhatun, Titik; Titik Apriyanti, Dwi; Susanto, Heru

2017-02-01

Chitosan is one of the natural polysaccharides, which is produced from chitin by deacetylation process. In this study, chitosan was produced from Amusium sp scallop shell waste. First, chitin was isolated by extraction via deproteinization using alkaline solution followed by demineralization using acid solution. Thereafter, chitosan was resulted from deacetylation of chitin using a high concentration of alkaline solution. The chemical structure of chitin and chitosan products was characterized using fourier transform infrared spectroscopy (FTIR).

Iron Homeostasis in Yellowstone National Park Hot Spring Microbial Communities

NASA Technical Reports Server (NTRS)

Brown, I.; Tringe, S. G.; Franklin, H.; Bryant, D. A.; Klatt, C. G.; Sarkisova, S. A.; Guevara, M.

2010-01-01

It has been postulated that life may have originated on Earth, and possibly on Mars, in association with hydrothermal activity and high concentrations of ferrous iron. However, it is not clear how an iron-rich thermal hydrosphere could be hospitable to microbes, since reduced iron appears to stimulate oxidative stress in all domains of life and particularly in oxygenic phototrophs. Therefore, the study of microbial diversity in iron-depositing hot springs (IDHS) and the mechanisms of iron homeostasis and suppression of oxidative stress may help elucidate how Precambrian organisms could withstand the extremely high concentrations of reactive oxygen species (ROS) produced by interaction between environmental Fe(2+) and O2. Proteins and clusters of orthologous groups (COGs) involved in the maintenance of Fe homeostasis found in cyanobacteria (CB) inhabiting environments with high and low [Fe] were main target of this analysis. Preliminary results of the analysis suggest that the Chocolate Pots (CP) microbial community is heavily dominated by phototrophs from the cyanobacteria (CB), Chloroflexi and Chlorobi phyla, while the Mushroom Spring (MS) effluent channel harbors a more diverse community in which Chloroflexi are the dominant phototrophs. It is speculated that CB inhabiting IDHS have an increased tolerance to both high concentrations of Fe(2+) and ROS produced in the Fenton reaction. This hypothesis was explored via a comparative analysis of the diversity of proteins and COGs involved in Fe and redox homeostasis in the CP and MS microbiomes.

Investigating the Use of Polymeric Binders in Twin Screw Melt Granulation Process for Improving Compactibility of Drugs.

PubMed

Batra, Amol; Desai, Dipen; Serajuddin, Abu T M

2017-01-01

Traditionally, the melt granulation for pharmaceutical products was performed at low temperature (<90°C) with high-shear granulators using low-melting waxy binders, and tablets produced using such granules were not amenable to large-scale manufacturing. The situation has changed in recent years by the use of twin screw extruder where the processing temperature could be increased to as high as 180°C and polymers with high T g could be used as binders. In this study, different polymeric binders were screened for their suitability in improving compactibility of 2 drugs, metformin hydrochloride and acetaminophen, by twin screw melt granulation. Processing temperatures for the 2 drugs were set at 180°C and 130°C, respectively. Screw configuration, screw speed, and feed rate were optimized such that all polymeric binders used produced granules. Several hydroxypropyl cellulose, hydroxypropyl methylcellulose, polyvinylpyrrolidone, and methacrylate-based polymers, including Klucel ® EXF, Eudragit ® EPO, and Soluplus ® , demonstrated good tablet tensile strength (>2 MPa) when granules were produced using only 10% wt/wt polymer concentration. Certain polymers provided acceptable compactibility even at 5% wt/wt. Thus, twin screw melt granulation process may be used with different polymers at a wide range of temperature. Due to low excipient concentration, this granulation method is especially suitable for high-dose tablets. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Microencapsulation of bioactive principles with an airless spray-gun suitable for processing high viscous solutions.

PubMed

Cocchietto, Moreno; Blasi, Paolo; Lapasin, Romano; Moro, Chiara; Gallo, Davide; Sava, Gianni

2013-11-19

to design, assemble and test a prototype of a novel production plant, suitable for producing microparticles (MPs) by processing highly viscous feed solutions (FSs). the prototype has been built using a commercial air compressor, a piston pump, an airless spray-gun, a customized air-treatment section, a timer, a rotating base, and a filtration section. Preliminary prototype parameter setting was carried out to individuate the best performing nozzle's dimension, the nebulization timing, and the CaCl2 concentration in the gelation fluid. In addition, prototype throughput (1 L to 5 L) and the range of practicable feed solution (FS) viscosities were assayed. A set of four batches was prepared in order to characterize the MPs, in terms of mean particle size and distribution, flow properties, swelling, encapsulation efficiency and release. according to a qualitative scoring, the large nozzle was suitable to nebulize FSs at a higher alginate concentration. Conversely, the small nozzle performed better in the processing of FSs with an alginate concentration up to 2% w/v. Only at the highest degree of viscosity, corresponding to 5% w/v of alginate, the FS processing was not technically possible. Among the CaCl2 concentrations considered, 15% w/v was recognized as the most versatile. The prototype appears to be convenient and suitable to grant a high yield starting from 2 L of FS. The flow behavior of the FSs assayed can be satisfactorily described with the Carreau-Yasuda equation and the throughput begins to slightly decrease for FSs at alginate concentrations exceeding 3% w/v. MP morphology was irregular with crumpled shape. The angle of repose indicates a good flowability and the release studies showed gastro-resistance and potential prolonged release applications. the novel prototype of production plant is suitable to process large amounts (2 L or more) of FSs, characterized by a high viscosity, to produce MPs suitable for bioactive principle delivery.

Microencapsulation of Bioactive Principles with an Airless Spray-Gun Suitable for Processing High Viscous Solutions

PubMed Central

Cocchietto, Moreno; Blasi, Paolo; Lapasin, Romano; Moro, Chiara; Gallo, Davide; Sava, Gianni

2013-01-01

Purpose: to design, assemble and test a prototype of a novel production plant, suitable for producing microparticles (MPs) by processing highly viscous feed solutions (FSs). Methods: the prototype has been built using a commercial air compressor, a piston pump, an airless spray-gun, a customized air-treatment section, a timer, a rotating base, and a filtration section. Preliminary prototype parameter setting was carried out to individuate the best performing nozzle’s dimension, the nebulization timing, and the CaCl2 concentration in the gelation fluid. In addition, prototype throughput (1 L to 5 L) and the range of practicable feed solution (FS) viscosities were assayed. A set of four batches was prepared in order to characterize the MPs, in terms of mean particle size and distribution, flow properties, swelling, encapsulation efficiency and release. Results: according to a qualitative scoring, the large nozzle was suitable to nebulize FSs at a higher alginate concentration. Conversely, the small nozzle performed better in the processing of FSs with an alginate concentration up to 2% w/v. Only at the highest degree of viscosity, corresponding to 5% w/v of alginate, the FS processing was not technically possible. Among the CaCl2 concentrations considered, 15% w/v was recognized as the most versatile. The prototype appears to be convenient and suitable to grant a high yield starting from 2 L of FS. The flow behavior of the FSs assayed can be satisfactorily described with the Carreau-Yasuda equation and the throughput begins to slightly decrease for FSs at alginate concentrations exceeding 3% w/v. MP morphology was irregular with crumpled shape. The angle of repose indicates a good flowability and the release studies showed gastro-resistance and potential prolonged release applications. Conclusions: the novel prototype of production plant is suitable to process large amounts (2 L or more) of FSs, characterized by a high viscosity, to produce MPs suitable for bioactive principle delivery. PMID:24956192

Effectiveness of household reverse-osmosis systems in a Western U.S. region with high arsenic in groundwater

USGS Publications Warehouse

Walker, M.; Seiler, R.L.; Meinert, M.

2008-01-01

It is well known to the public in Lahontan Valley in rural Nevada, USA, that local aquifers produce water with varied, but sometimes very high concentrations of arsenic (> 4??ppm). As a result, many residents of the area have installed household reverse-osmosis (RO) systems to produce drinking water. We examined performance of RO systems and factors associated with arsenic removal efficiency in 59 households in Lahontan Valley. The sampling results indicated that RO systems removed an average of 80.2% of arsenic from well water. In 18 of the 59 households, arsenic concentrations exceeded 10??ppb in treated water, with a maximum in treated water of 180??ppb. In 3 of the 59 households, RO treatment had little effect on specific conductance, indicating that the RO system was not working properly. Two main factors lead to arsenic levels in treated water exceeding drinking-water standards in the study area. First, arsenic concentrations were high enough in some Lahontan Valley wells that arsenic levels exceeded 10??ppb even though RO treatment removed more than 95% of the arsenic. Second, trivalent As+ 3 was the dominant arsenic species in approximately 15% of the wells, which significantly reduced treatment efficiency. Measurements of specific conductance indicated that efficiency in reducing arsenic levels did not always correlate with reductions in total dissolved solids. As a consequence, improvements in taste of the water or simple measurements of specific conductance made by technicians to test RO systems can mislead the public into assuming the water meets safety standards. Actual measurements of treated water are necessary to assure that household RO systems are reducing arsenic concentrations to safe levels, particularly in areas where groundwater has high arsenic concentrations or where As+ 3 is the dominant species. ?? 2007 Elsevier B.V. All rights reserved.

[Toxicity of Coptis chinensis Rhizome Extracts to Green Algae].

PubMed

Chen, Ya-nan; Yuan, Ling

2015-05-01

Coptis chinensis contains antiseptic alkaloids and thus its rhizomes and preparations are widely used for the treatment of.fish diseases. In order to realize the risk of water ecosystems produced by this medical herb and preparations used in aquaculture, the present experiment was carried out to study the toxicity of Coptis chinensis rhizome extract (CRE) to Scenedesmus oblique and Chlorella pyrenoidosa grown in culture solution with 0.00 (CK), 0.088 (Tl), 0.44 (T2) and 1.76 mg · L(-1) (T3) of CRE, respectively. The results show that low concentration of CRE (T1) inhibited the growth rate of the alga and high CRE (T2 and T3) ceased growth and reproductions. CRE also decreased the chlorophyll and proteins in alga cells, indicating the inhibition of photosynthesis and protein biosynthesis, which could be direct reasons for the low growth rate and death of green alga. The efflux of protons and substances from alga cells led to pH reduction and conductivity increment in culture solution with CRE. Furthermore, the activity of superoxide dismutase in alga increased at the beginning of CRE in T1 and T2 treatments but decreased as time prolonged which was in contrast to high CRE treatment. And the long exposure to low CRE treatment behaved otherwise. This suggests that the low concentration of CRE could induce the resistant reactions in alga at initial time but high CRE concentration or long exposure even at low CRE concentration could inhibit the enzyme synthesis. Similarly, malondialdehyde in alga increased as CRE concentrations increased in culture solutions, implying the damage and high permeability of cell membrane. In general, Chlorella pyrenoidosa was more sensitive to CRE. The abuse of rhizomes and preparations in aquaculture and intensive cultivation of Coptis chinensis plants in a large scale might produce ecological risks to primary productivity of water ecosystems.

Effects of seasonal operation on the quality of water produced by public-supply wells

USGS Publications Warehouse

Bexfield, Laura M.; Jurgens, Bryant C.

2014-01-01

Seasonal variability in groundwater pumping is common in many places, but resulting effects of seasonal pumping stress on the quality of water produced by public-supply wells are not thoroughly understood. Analysis of historical water-quality samples from public-supply wells completed in deep basin-fill aquifers in Modesto, California (134 wells) and Albuquerque, New Mexico (95 wells) indicates that several wells have seasonal variability in concentrations of contaminants of concern. In Modesto, supply wells are more likely to produce younger groundwater with higher nitrate and uranium concentrations during the summer (high) pumping season than during the winter (low) pumping season. In Albuquerque, supply wells are more likely to produce older groundwater with higher arsenic concentrations during the winter pumping season than during the summer pumping season. Seasonal variability in contaminant concentrations in Modesto is influenced primarily by effects of summer pumping on vertical hydraulic gradients that drive migration of shallow groundwater through the aquifer to supply wells. Variability in Albuquerque is influenced primarily by the period of time that a supply well is idle, allowing its wellbore to act as a conduit for vertical groundwater flow and contaminant migration. However, both processes are observed in each study area. Similar findings would appear to be likely in other alluvial basins with stratified water quality and substantial vertical head gradients. Results suggest that even in aquifers dominated by old groundwater, changes to seasonal pumping patterns and/or to depth of well completion can help reduce vulnerability to selected contaminants of either natural or anthropogenic origin.

Effects of Seasonal Operation on the Quality of Water Produced by Public-Supply Wells

PubMed Central

Bexfield, Laura M; Jurgens, Bryant C

2014-01-01

Seasonal variability in groundwater pumping is common in many places, but resulting effects of seasonal pumping stress on the quality of water produced by public-supply wells are not thoroughly understood. Analysis of historical water-quality samples from public-supply wells completed in deep basin-fill aquifers in Modesto, California (134 wells) and Albuquerque, New Mexico (95 wells) indicates that several wells have seasonal variability in concentrations of contaminants of concern. In Modesto, supply wells are more likely to produce younger groundwater with higher nitrate and uranium concentrations during the summer (high) pumping season than during the winter (low) pumping season. In Albuquerque, supply wells are more likely to produce older groundwater with higher arsenic concentrations during the winter pumping season than during the summer pumping season. Seasonal variability in contaminant concentrations in Modesto is influenced primarily by effects of summer pumping on vertical hydraulic gradients that drive migration of shallow groundwater through the aquifer to supply wells. Variability in Albuquerque is influenced primarily by the period of time that a supply well is idle, allowing its wellbore to act as a conduit for vertical groundwater flow and contaminant migration. However, both processes are observed in each study area. Similar findings would appear to be likely in other alluvial basins with stratified water quality and substantial vertical head gradients. Results suggest that even in aquifers dominated by old groundwater, changes to seasonal pumping patterns and/or to depth of well completion can help reduce vulnerability to selected contaminants of either natural or anthropogenic origin. PMID:24593780

Heterogeneous pumice populations in the 2.08-Ma Cerro Galán Ignimbrite: Implications for magma recharge and ascent preceding a large-volume silicic eruption

USGS Publications Warehouse

Wright, Heather M.; Folkes, Christopher B.; Cas, Ray A.F.; Cashman, Katharine V.

2011-01-01

Triggering mechanisms of large silicic eruptions remain a critical unsolved problem. We address this question for the ~2.08-Ma caldera-forming eruption of Cerro Galán volcano, Argentina, which produced distinct pumice populations of two colors: grey (5%) and white (95%) that we believe may hold clues to the onset of eruptive activity. We demonstrate that the color variations correspond to both textural and compositional variations between the clast types. Both pumice types have bulk compositions of high-K, high-silica dacite to low-silica rhyolite, but there are sufficient compositional differences (e.g., ~150 ppm lower Ba at equivalent SiO2 content and 0.03 wt.% higher TiO2 in white pumice than grey) to suggest that the two pumice populations are not related by simple fractionation. Trace element concentrations in crystals mimic bulk variations between clast types, with grey pumice containing elevated Ba, Cu, Pb, and Zn concentrations in both bulk samples (average Cu, Pb, and Zn concentrations are 27, 35, and 82 in grey pumice vs. 11, 19, and 60 in white pumice) and biotite phenocrysts and white pumice showing elevated Li concentrations in biotite and plagioclase phenocrysts. White and grey clasts are also texturally distinct: White pumice clasts contain abundant phenocrysts (44–57%), lack microlites, and have highly evolved groundmass glass compositions (76.4–79.6 wt.% SiO2), whereas grey pumice clasts contain a lower percentage of phenocrysts/microphenocrysts (35–49%), have abundant microlites, and have less evolved groundmass glass compositions (69.4–73.8 wt.% SiO2). There is also evidence for crystal transfer between magma producing white and grey pumice. Thin highly evolved melt rims surround some fragmental crystals in grey pumice clasts and appear to have come from magma that produced white pumice. Furthermore, based on crystal compositions, white bands within banded pumice contain crystals originating in grey magma. Finally, only grey pumice clasts form breadcrusted surface textures. We interpret these compositional and textural variations to indicate distinct magma batches, where grey pumice originated from an originally deeper, more volatile-rich dacite recharge magma that ascended through and mingled with the volumetrically dominant, more highly crystalline chamber that produced white pumice. Shortly before eruption, the grey pumice magma stalled within shallow fractures, forming a vanguard magma phase whose ascent may have provided a trigger for eruption of the highly crystalline rhyodacite magma. We suggest that in the case of the Cerro Galán eruption, grey pumice provides evidence not only for cryptic silicic recharge in a large caldera system but also a probable trigger for the eruption.

Heterogeneous pumice populations in the 2.08-Ma Cerro Galán Ignimbrite: implications for magma recharge and ascent preceding a large-volume silicic eruption

NASA Astrophysics Data System (ADS)

Wright, Heather M. N.; Folkes, Chris B.; Cas, Raymond A. F.; Cashman, Katharine V.

2011-12-01

Triggering mechanisms of large silicic eruptions remain a critical unsolved problem. We address this question for the ~2.08-Ma caldera-forming eruption of Cerro Galán volcano, Argentina, which produced distinct pumice populations of two colors: grey (5%) and white (95%) that we believe may hold clues to the onset of eruptive activity. We demonstrate that the color variations correspond to both textural and compositional variations between the clast types. Both pumice types have bulk compositions of high-K, high-silica dacite to low-silica rhyolite, but there are sufficient compositional differences (e.g., ~150 ppm lower Ba at equivalent SiO2 content and 0.03 wt.% higher TiO2 in white pumice than grey) to suggest that the two pumice populations are not related by simple fractionation. Trace element concentrations in crystals mimic bulk variations between clast types, with grey pumice containing elevated Ba, Cu, Pb, and Zn concentrations in both bulk samples (average Cu, Pb, and Zn concentrations are 27, 35, and 82 in grey pumice vs. 11, 19, and 60 in white pumice) and biotite phenocrysts and white pumice showing elevated Li concentrations in biotite and plagioclase phenocrysts. White and grey clasts are also texturally distinct: White pumice clasts contain abundant phenocrysts (44-57%), lack microlites, and have highly evolved groundmass glass compositions (76.4-79.6 wt.% SiO2), whereas grey pumice clasts contain a lower percentage of phenocrysts/microphenocrysts (35-49%), have abundant microlites, and have less evolved groundmass glass compositions (69.4-73.8 wt.% SiO2). There is also evidence for crystal transfer between magma producing white and grey pumice. Thin highly evolved melt rims surround some fragmental crystals in grey pumice clasts and appear to have come from magma that produced white pumice. Furthermore, based on crystal compositions, white bands within banded pumice contain crystals originating in grey magma. Finally, only grey pumice clasts form breadcrusted surface textures. We interpret these compositional and textural variations to indicate distinct magma batches, where grey pumice originated from an originally deeper, more volatile-rich dacite recharge magma that ascended through and mingled with the volumetrically dominant, more highly crystalline chamber that produced white pumice. Shortly before eruption, the grey pumice magma stalled within shallow fractures, forming a vanguard magma phase whose ascent may have provided a trigger for eruption of the highly crystalline rhyodacite magma. We suggest that in the case of the Cerro Galán eruption, grey pumice provides evidence not only for cryptic silicic recharge in a large caldera system but also a probable trigger for the eruption.

Metabolic differences of industrial acarbose-producing Actinoplanes sp. A56 under various osmolality levels.

PubMed

Li, Kun-tai; Peng, Wei-fu; Xia, Wei; Huang, Lin; Cheng, Xin

2016-01-01

Many investigations have revealed that a certain concentration of osmolality was indispensable for efficient acarbose production, but little information was available on the response mechanism of acarbose-producing strains to osmotic stress. By using the gas chromatography-mass spectrometry (GC-MS) analysis coupled with the enzyme activity determination of central carbon metabolism, the present work investigated the metabolic characteristics of industrial acarbose-producing Actinoplanes sp. A56 under various osmolality levels. Relatively high osmolality (450-500 mOsm/kg) appeared to favor efficient acarbose production by Actinoplanes sp. A56, although it inhibited cell growth. Further GC-MS analysis showed that fatty acids were the uppermost differential intracellular metabolites under various osmolality levels, and the relatively high osmolality resulted in increases in levels of fatty acids.

High concentrations of protein test substances may have non-toxic effects on Daphnia magna: implications for regulatory study designs and ecological risk assessments for GM crops.

PubMed

Raybould, Alan; Burns, Andrea; Hamer, Mick

2014-01-01

Laboratory testing for possible adverse effects of insecticidal proteins on non-target organisms (NTOs) is an important part of many ecological risk assessments for regulatory decision-making about the cultivation of insect-resistant genetically modified (IRGM) crops. To increase confidence in the risk assessments, regulatory guidelines for effects testing specify that representative surrogate species for NTOs are exposed to concentrations of insecticidal proteins that are in excess of worst-case predicted exposures in the field. High concentrations in effects tests are achieved by using protein test substances produced in microbes, such as Escherichia coli. In a study that exposed Daphnia magna to a single high concentration of a microbial test substance containing Vip3Aa20, the insecticidal protein in MIR162 maize, small reductions in growth were observed. These effects were surprising as many other studies strongly suggest that the activity of Vip3Aa20 is limited to Lepidoptera. A plausible explanation for the effect on growth is that high concentrations of test substance have a non-toxic effect on Daphnia, perhaps by reducing its feeding rate. A follow-up study tested that hypothesis by exposing D. magna to several concentrations of Vip3Aa20, and a high concentration of a non-toxic protein, bovine serum albumin (BSA). Vip3Aa20 and BSA had sporadic effects on the reproduction and growth of D. magna. The pattern of the effects suggests that they result from non-toxic effects of high concentrations of protein, and not from toxicity. The implications of these results for regulatory NTO effects testing and ERA of IRGM crops are discussed.

Effect of Infusion Method and Parameters on Mass Transfer in Blueberries

USDA-ARS?s Scientific Manuscript database

In order to obtain optimal processing conditions for producing infused blueberries with high solid gain, we investigated the infusion characteristics of blueberries under various processing parameters in sugar solutions with 1:1 ratio of solution and berries. Static batch constant concentration inf...

Fractionation, partial characterization and bioactivity of water-soluble polysaccharides and polysaccharide-protein complexes from Pleurotus geesteranus.

PubMed

Zhang, Mei; Zhu, Lin; Cui, Steve W; Wang, Qi; Zhou, Ting; Shen, Hengsheng

2011-01-01

Fractionation and purification of mushroom polysaccharides is a critical process for mushroom clinical application. After a hot-water treatment, the crude Pleurotus geesteranus (PG) was further fractionated into four fractions (PG-1, -2, -3, -4) using gradient precipitation with water and ammonia sulphate. By controlling the initial polymer concentration and ratio of solvents, this process produced PG fractions with high chemical uniformity and narrow Mw distribution without free proteins. Structurally, PG-1 and PG-2 are pure homopolysaccharide mainly composed of glucose; and PG-3 and PG-4 are heteropolysaccharide-protein complexes. PG-2, a high M(w) fraction mainly composed of glucose presented significant cytotoxicity at the concentration of 200 and 100 μg/ml to human breast cancer cells. Here, we report a new mushroom polysaccharides extraction and fractionation method, with which we produced four fractions of PG with PG-2 appearing effective anti-tumour activity. Crown Copyright © 2010. Published by Elsevier B.V. All rights reserved.

Determination of sulfuric acid concentration for anti-cavitation characteristics of Al alloy by two step anodizing process to forming nano porous.

PubMed

Lee, Seung-Jun; Kim, Seong-Kweon; Jeong, Jae-Yong; Kim, Seong-Jong

2014-12-01

Al alloy is a highly active metal but forms a protective oxide film having high corrosion resistance in atmosphere environment. However, the oxide film is not suitable for practical use, since the thickness of the film is not uniform and it is severly altered with formation conditions. This study focused on developing an aluminum anodizing layer having hardness, corrosion resistance and abrasion resistance equivalent to a commercial grade protective layer. Aluminum anodizing layer was produced by two-step aluminum anodizing oxide (AAO) process with different sulfuric acid concentrations, and the cavitation characteristics of the anodized coating layer was investigated. In hardness measurement, the anodized coating layer produced with 15 vol.% of sulfuric acid condition had the highest value of hardness but exhibited poor cavitation resistance due to being more brittle than those with other conditions. The 10 vol.% of sulfuric acid condition was thus considered to be the optimum condition as it had the lowest weight loss and damage depth.

Recent Advances on Bioethanol Dehydration using Zeolite Membrane

NASA Astrophysics Data System (ADS)

Makertihartha, I. G. B. N.; Dharmawijaya, P. T.; Wenten, I. G.

2017-07-01

Renewable energy has gained increasing attention throughout the world. Bioethanol has the potential to replace existing fossil fuel usage without much modification in existing facilities. Bioethanol which generally produced from fermentation route produces low ethanol concentration. However, fuel grade ethanol requires low water content to avoid engine stall. Dehydration process has been increasingly important in fuel grade ethanol production. Among all dehydration processes, pervaporation is considered as the most promising technology. Zeolite possesses high potential in pervaporation of bioethanol into fuel grade ethanol. Zeolite membrane can either remove organic (ethanol) from aqueous mixture or water from the mixture, depending on the framework used. Hydrophilic zeolite membrane, e.g. LTA, can easily remove water from the mixture leaving high ethanol concentration. On the other hand, hydrophobic zeolite membrane, e.g. silicate-1, can remove ethanol from aqueous solution. This review presents the concept of bioethanol dehydration using zeolite membrane. Special attention is given to the performance of selected pathway related to framework selection.

Second-generation ethanol production from elephant grass at high total solids.

PubMed

Menegol, Daiane; Fontana, Roselei Claudete; Dillon, Aldo José Pinheiro; Camassola, Marli

2016-07-01

The enzymatic hydrolysis of Pennisetum purpureum (elephant grass) was evaluated at high total solid levels (from 4% to 20% (w/v)) in a concomitant ball milling treatment in a rotating hydrolysis reactor (RHR). The greatest glucose yield was 20.17% when 4% (w/v) untreated biomass was employed. When sugars obtained from enzymatic hydrolysis were submitted to fermentation with Saccharomyces cerevisiae, the greatest ethanol yield was 22.61% when 4% (w/v) untreated biomass was employed; however, the highest glucose concentration (12.47g/L) was obtaining using 20% (w/v) solids and highest ethanol concentration (6.1g/L) was obtained using 16% (w/v) solids. When elephant grass was hydrolyzed in the rotating hydrolysis reactor, ethanol production was about double that was produced when the biomass was hydrolyzed in a static reactor (SR). These data indicate that it is possible to produce ethanol from elephant grass when milling treatment and enzymatic hydrolysis are performed at the same time. Copyright © 2016. Published by Elsevier Ltd.

Fabrication of Titania Nanotubes for Gas Sensing Applications

NASA Astrophysics Data System (ADS)

Dzilal, A. A.; Muti, M. N.; John, O. D.

2010-03-01

Detection of hydrogen is needed for industrial process control and medical applications where presence of hydrogen indicates different type of health problems. Titanium dioxide nanotube structure is chosen as an active component in the gas sensor because of its highly sensitive electrical resistance to hydrogen over a wide range of concentrations. The objective of the work is to fabricate good quality titania nanotubes suitable for hydrogen sensing applications. The fabrication method used is anodizing method. The anodizing parameters namely the voltage, time duration, concentration of hydrofluoric acid in water, separation between the electrodes and the ambient temperature are varied accordingly to find the optimum anodizing conditions for production of good quality titania nanotubes. The highly ordered porous titania nanotubes produced by this method are in tabular shape and have good uniformity and alignment over large areas. From the investigation done, certain set of anodizing parameters have been found to produce good quality titania nanotubes with diameter ranges from 47 nm to 94 nm.

Airborne measurements of cloud-forming nuclei and aerosol particles in stabilized ground clouds produced by solid rocket booster firings

NASA Technical Reports Server (NTRS)

Hindman, E. E., II; Ala, G. G.; Parungo, F. P.; Willis, P. T.; Bendura, R. J.; Woods, D.

1978-01-01

Airborne measurements of cloud volumes, ice nuclei and cloud condensation nuclei, liquid particles, and aerosol particles were obtained from stabilized ground clouds (SGCs) produced by Titan 3 launches at Kennedy Space Center, 20 August and 5 September 1977. The SGCs were bright, white, cumulus clouds early in their life and contained up to 3.5 g/m3 of liquid in micron to millimeter size droplets. The measured cloud volumes were 40 to 60 cu km five hours after launch. The SGCs contained high concentrations of cloud condensation nuclei active at 0.2%, 0.5%, and 1.0% supersaturation for periods of three to five hours. The SGCs also contained high concentrations of submicron particles. Three modes existed in the particle population: a 0.05 to 0.1 micron mode composed of aluminum-containing particles, a 0.2 to 0.8 micron mode, and a 2.0 to 10 micron mode composed of particles that contained primarily aluminum.

Spatial distribution and historical trends of heavy metals in the sediments of petroleum producing regions of the Beibu Gulf, China.

PubMed

Yang, Jichao; Wang, Weiguo; Zhao, Mengwei; Chen, Bin; Dada, Olusegun A; Chu, Zhihui

2015-02-15

The concentrations of As, Sb, Hg, Pb, Cd, and Ba in the surface and core sediments of the oil and gas producing region of the Beibu Gulf were measured by Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES), Inductively Coupled Plasma Mass Spectrometry (ICP-MS) and Atomic Fluorescence Spectrometry (AFS), and the spatial distribution and historical trends of these elements are discussed. The results show that the concentrations of these elements are highest near the platforms. The results of Enrichment Factor (EF) and Potential Ecological Risk Index (PERI) also reveal significantly higher enrichment around the platforms, which imply that the offshore petroleum production was the cause of the unusual distribution and severe enrichment of these elements in the study area. The environment around the platforms was highly laden with toxic elements, thereby representing a very high ecological risk to the environment of the study area. Copyright © 2014 Elsevier Ltd. All rights reserved.

Friction and wear of iron-base binary alloys in sliding contact with silicon carbide in vacuum

NASA Technical Reports Server (NTRS)

Miyoshi, K.; Buckley, D. H.

1980-01-01

Multipass sliding friction experiments were conducted with various iron base binary alloys in contact with a single crystal silicon carbide surface in vacuum. Results indicate that the atomic size and concentration of alloy elements play important roles in controlling the transfer and friction properties of iron base binary alloys. Alloys having high solute concentration produce more transfer than do alloys having low solute concentration. The coefficient of friction during multipass sliding generally increases with an increase in the concentration of alloying element. The change of friction with succeeding passes after the initial pass also increases as the solute to iron, atomic radius ratio increases or decreases from unity.

Designing and creating Saccharomyces interspecific hybrids for improved, industry relevant, phenotypes.

PubMed

Bellon, Jennifer R; Yang, Fei; Day, Martin P; Inglis, Debra L; Chambers, Paul J

2015-10-01

To remain competitive in increasingly overcrowded markets, yeast strain development programmes are crucial for fermentation-based food and beverage industries. In a winemaking context, there are many yeast phenotypes that stand to be improved. For example, winemakers endeavouring to produce sweet dessert wines wrestle with fermentation challenges particular to fermenting high-sugar juices, which can lead to elevated volatile acidity levels and extended fermentation times. In the current study, we used natural yeast breeding techniques to generate Saccharomyces spp. interspecific hybrids as a non-genetically modified (GM) strategy to introduce targeted improvements in important, wine-relevant traits. The hybrids were generated by mating a robust wine strain of Saccharomyces cerevisiae with a wine isolate of Saccharomyces bayanus, a species previously reported to produce wines with low concentrations of acetic acid. Two hybrids generated from the cross showed robust fermentation properties in high-sugar grape juice and produced botrytised Riesling wines with much lower concentrations of acetic acid relative to the industrial wine yeast parent. The hybrids also displayed suitability for icewine production when bench-marked against an industry standard icewine yeast, by delivering icewines with lower levels of acetic acid. Additionally, the hybrid yeast produced wines with novel aroma and flavour profiles and established that choice of yeast strain impacts on wine colour. These new hybrid yeasts display the desired targeted fermentation phenotypes from both parents, robust fermentation in high-sugar juice and the production of wines with low volatile acidity, thus establishing their suitability for wine styles that are traditionally troubled by excessive volatile acidity levels.

Adsorption and oxidation of SO₂in a fixed-bed reactor using activated carbon produced from oxytetracycline bacterial residue and impregnated with copper.

PubMed

Zhou, Baohua; Yu, Lei; Song, Hanning; Li, Yaqi; Zhang, Peng; Guo, Bin; Duan, Erhong

2015-02-01

The SO₂removal ability (including adsorption and oxidation ability) of activated carbon produced from oxytetracycline bacterial residue and impregnated with copper was investigated. The activated carbon produced from oxytetracycline bacterial residue and modified with copper was characterized by x-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy. The effects of the catalysts, SO₂concentration, weight hourly space velocity, and temperature on the SO₂adsorption and oxidation activity were evaluated. Activated carbon produced from oxytetracycline bacterial residue and used as catalyst supports for copper oxide catalysts provided high catalytic activity for the adsorbing and oxidizing of SO₂from flue gases.

The role of Cra in regulating acetate excretion and osmotic tolerance in E. coli K-12 and E. coli B at high density growth

PubMed Central

2011-01-01

Background E. coli B (BL21), unlike E.coli K-12 (JM109) is insensitive to glucose concentration and, therefore, grows faster and produces less acetate than E. coli K-12, especially when growing to high cell densities at high glucose concentration. By performing genomic analysis, it was demonstrated that the cause of this difference in sensitivity to the glucose concentration is the result of the differences in the central carbon metabolism activity. We hypothesized that the global transcription regulator Cra (FruR) is constitutively expressed in E. coli B and may be responsible for the different behaviour of the two strains. To investigate this possibility and better understand the function of Cra in the two strains, cra - negative E. coli B (BL21) and E. coli K-12 (JM109) were prepared and their growth behaviour and gene expression at high glucose were evaluated using microarray and real-time PCR. Results The deletion of the cra gene in E. coli B (BL21) minimally affected the growth and maximal acetate accumulation, while the deletion of the same gene in E.coli K-12 (JM109) caused the cells to stop growing as soon as acetate concentration reached 6.6 g/L and the media conductivity reached 21 mS/cm. ppsA (gluconeogenesis gene), aceBA (the glyoxylate shunt genes) and poxB (the acetate producing gene) were down-regulated in both strains, while acs (acetate uptake gene) was down-regulated only in E.coli B (BL21). These transcriptional differences had little effect on acetate and pyruvate production. Additionally, it was found that the lower growth of E. coli K-12 (JM109) strain was the result of transcription inhibition of the osmoprotectant producing bet operon (betABT). Conclusions The transcriptional changes caused by the deletion of cra gene did not affect the activity of the central carbon metabolism, suggesting that Cra does not act alone; rather it interacts with other pleiotropic regulators to create a network of metabolic effects. An unexpected outcome of this work is the finding that cra deletion caused transcription inhibition of the bet operon in E. coli K-12 (JM109) but did not affect this operon transcription in E. coli B (BL21). This property, together with the insensitivity to high glucose concentrations, makes this the E. coli B (BL21) strain more resistant to environmental changes. PMID:21718532

Synchronisation of ovulation for management of reproduction in dairy cows.

PubMed

Bisinotto, R S; Ribeiro, E S; Santos, J E P

2014-05-01

Important developments have occurred in the last two decades, since the advent of the Ovsynch protocol, on the understanding and use of synchronisation programmes for management of reproduction in dairy herds. This better understanding of oestrus cycle control associated with suboptimal reproductive performance in dairy herds has led dairy producers to quickly adopt timed artificial insemination (AI) protocols. Recent surveys have documented that fixed-time AI has become an important component of management of reproduction in high-producing herds. Furthermore, timed AI protocols have also demonstrated benefits in pasture-based milk production systems because of the ability to increase insemination rate. In general, successful use of the Ovsynch protocol requires some fundamental physiological principles to be respected, including: induction of ovulation to synchronise follicle growth in the first 2 days of the programme such that a young antral follicle is recruited; maintenance of high concentrations of progesterone during the development of the ovulatory follicle, but also effectively lyse the corpus luteum to result in very low concentration of progesterone at AI; and having a healthy pre-ovulatory follicle of moderate diameter that is highly oestrogenic and responsive to gonadotropins to synchronously ovulate 12 to 18 h after insemination. Current methods oestrous and ovulation synchronisation are still not optimal and future improvements will likely require new technologies for hormone formulation and delivery such that additional interventions are minimised to maintain acceptance by producers.

High efficiency solar cells for concentrator systems: silicon or multi-junction?

NASA Astrophysics Data System (ADS)

Slade, Alexander; Stone, Kenneth W.; Gordon, Robert; Garboushian, Vahan

2005-08-01

Amonix has become the first company to begin production of high concentration silicon solar cells where volumes are over 10 MW/year. Higher volumes are available due to the method of manufacture; Amonix solely uses semiconductor foundries for solar cell production. In the previous years of system and cell field testing, this method of manufacturing enabled Amonix to maintain a very low overhead while incurring a high cost for the solar cell. However, recent simplifications to the solar cell processing sequence resulted in cost reduction and increased yield. This new process has been tested by producing small qualities in very short time periods, enabling a simulation of high volume production. Results have included over 90% wafer yield, up to 100% die yield and world record performance (η =27.3%). This reduction in silicon solar cell cost has increased the required efficiency for multi-junction concentrator solar cells to be competitive / advantageous. Concentrator systems are emerging as a low-cost, high volume option for solar-generated electricity due to the very high utilization of the solar cell, leading to a much lower $/Watt cost of a photovoltaic system. Parallel to this is the onset of alternative solar cell technologies, such as the very high efficiency multi-junction solar cells developed at NREL over the last two decades. The relatively high cost of these type of solar cells has relegated their use to non-terrestrial applications. However, recent advancements in both multi-junction concentrator cell efficiency and their stability under high flux densities has made their large-scale terrestrial deployment significantly more viable. This paper presents Amonix's experience and testing results of both high-efficiency silicon rear-junction solar cells and multi-junction solar cells made for concentrated light operation.

The impact of commercially treated oil and gas produced water discharges on bromide concentrations and modeled brominated trihalomethane disinfection byproducts at two downstream municipal drinking water plants in the upper Allegheny River, Pennsylvania, USA.

PubMed

Landis, Matthew S; Kamal, Ali S; Kovalcik, Kasey D; Croghan, Carry; Norris, Gary A; Bergdale, Amy

2016-01-15

In 2010, a dramatic increase in the levels of total trihalomethane (THM) and the relative proportion of brominated species was observed in finished water at several Pennsylvania water utilities (PDW) using the Allegheny River as their raw water supply. An increase in bromide (Br(-)) concentrations in the Allegheny River was implicated to be the cause of the elevated water disinfection byproducts. This study focused on quantifying the contribution of Br(-) from a commercial wastewater treatment facility (CWTF) that solely treats wastes from oil and gas producers and discharges into the upper reaches of the Allegheny River, and impacts on two downstream PDWs. In 2012, automated daily integrated samples were collected on the Allegheny River at six sites during three seasonal two-week sampling campaigns to characterize Br(-) concentrations and river dispersion characteristics during periods of high and low river discharges. The CWTF discharges resulted in significant increases in Br(-) compared to upstream baseline values in PDW raw drinking water intakes during periods of low river discharge. During high river discharge, the assimilative dilution capacity of the river resulted in lower absolute halide concentrations, but significant elevations Br(-) concentrations were still observed at the nearest downstream PDW intake over baseline river levels. On days with active CWTF effluent discharge the magnitude of bromide impact increased by 39 ppb (53%) and 7 ppb (22%) for low and high river discharge campaigns, respectively. Despite a declining trend in Allegheny River Br(-) (2009-2014), significant impacts from CWTF and coal-fired power plant discharges to Br(-) concentrations during the low river discharge regime at downstream PDW intakes was observed, resulting in small modeled increases in total THM (3%), and estimated positive shifts (41-47%) to more toxic brominated THM analogs. The lack of available coincident measurements of THM, precursors, and physical parameters limited the interpretation of historical trends. Published by Elsevier B.V.

The Impact of Ship-Produced Aerosols on the Microstructure and Albedo of Warm Marine Stratocumulus Clouds: A Test of MAST Hypotheses 1i and 1ii.

NASA Astrophysics Data System (ADS)

Durkee, P. A.; Noone, K. J.; Ferek, R. J.; Johnson, D. W.; Taylor, J. P.; Garrett, T. J.; Hobbs, P. V.; Hudson, J. G.; Bretherton, C. S.; Innis, G.; Frick, G. M.; Hoppel, W. A.; O'Dowd, C. D.; Russell, L. M.; Gasparovic, R.; Nielsen, K. E.; Tessmer, S. A.; Öström, E.;  Osborne, S. R.;  Flagan, R. C.;  Seinfeld, J. H.;  Rand, H.

2000-08-01

Anomalously high reflectivity tracks in stratus and stratocumulus sheets associated with ships (known as ship tracks) are commonly seen in visible and near-infrared satellite imagery. Until now there have been only a limited number of in situ measurements made in ship tracks. The Monterey Area Ship Track (MAST) experiment, which was conducted off the coast of California in June 1994, provided a substantial dataset on ship emissions and their effects on boundary layer clouds. Several platforms, including the University of Washington C-131A aircraft, the Meteorological Research Flight C-130 aircraft, the National Aeronautics and Space Administration ER-2 aircraft, the Naval Research Laboratory airship, the Research Vessel Glorita, and dedicated U.S. Navy ships, participated in MAST in order to study processes governing the formation and maintenance of ship tracks.This paper tests the hypotheses that the cloud microphysical changes that produce ship tracks are due to (a) particulate emission from the ship's stack and/or (b) sea-salt particles from the ship's wake. It was found that ships powered by diesel propulsion units that emitted high concentrations of aerosols in the accumulation mode produced ship tracks. Ships that produced few particles (such as nuclear ships), or ships that produced high concentrations of particles but at sizes too small to be activated as cloud drops in typical stratocumulus (such as gas turbine and some steam-powered ships), did not produce ship tracks. Statistics and case studies, combined with model simulations, show that provided a cloud layer is susceptible to an aerosol perturbation, and the atmospheric stability enables aerosol to be mixed throughout the boundary layer, the direct emissions of cloud condensation nuclei from the stack of a diesel-powered ship is the most likely, if not the only, cause of the formation of ship tracks. There was no evidence that salt particles from ship wakes cause ship tracks.

Effects of Chitosan on Candida albicans: Conditions for Its Antifungal Activity

PubMed Central

Peña, Antonio; Sánchez, Norma Silvia; Calahorra, Martha

2013-01-01

The effects of low molecular weight (96.5 KDa) chitosan on the pathogenic yeast Candida albicans were studied. Low concentrations of chitosan, around 2.5 to 10 μg·mL−1 produced (a) an efflux of K+ and stimulation of extracellular acidification, (b) an inhibition of Rb+ uptake, (c) an increased transmembrane potential difference of the cells, and (d) an increased uptake of Ca2+. It is proposed that these effects are due to a decrease of the negative surface charge of the cells resulting from a strong binding of the polymer to the cells. At higher concentrations, besides the efflux of K+, it produced (a) a large efflux of phosphates and material absorbing at 260 nm, (b) a decreased uptake of Ca2+, (c) an inhibition of fermentation and respiration, and (d) the inhibition of growth. The effects depend on the medium used and the amount of cells, but in YPD high concentrations close to 1 mg·mL−1 are required to produce the disruption of the cell membrane, the efflux of protein, and the growth inhibition. Besides the findings at low chitosan concentrations, this work provides an insight of the conditions required for chitosan to act as a fungistatic or antifungal and proposes a method for the permeabilization of yeast cells. PMID:23844364

Shifting the balance of fermentation products between hydrogen and volatile fatty acids: microbial community structure and function.

PubMed

Miceli, Joseph F; Torres, César I; Krajmalnik-Brown, Rosa

2016-12-01

Fermentation is a key process in many anaerobic environments. Varying the concentration of electron donor fed to a fermenting community is known to shift the distribution of products between hydrogen, fatty acids and alcohols. Work to date has focused mainly on the fermentation of glucose, and how the microbial community structure is affected has not been explored. We fed ethanol, lactate, glucose, sucrose or molasses at 100 me- eq. L -1 , 200 me- eq. L -1 or 400 me- eq. L -1 to batch-fed cultures with fermenting, methanogenic communities. In communities fed high concentrations of electron donor, the fraction of electrons channeled to methane decreased, from 34% to 6%, while the fraction of electrons channeled to short chain fatty acids increased, from 52% to 82%, averaged across all electron donors. Ethanol-fed cultures did not produce propionate, but did show an increase in electrons directed to acetate as initial ethanol concentration increased. In glucose, sucrose, molasses and lactate-fed cultures, propionate accumulation co-occurred with known propionate producing organisms. Overall, microbial communities were determined by the substrate provided, rather than its initial concentration, indicating that a change in community function, rather than community structure, is responsible for shifts in the fermentation products produced. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Production of terpenes in the culture of Chlorophyceae and Rhodophyta

NASA Astrophysics Data System (ADS)

Abe, M.; Hashimoto, S.

2014-12-01

Terpenes show high reactivity in the troposphere, contributing to organic aerosol reactions with OH radicals. One of the main sources of terpenes in the atmosphere is terrestrial plants. It has been recently reported that marine phytoplankton also produce monoterpenes (Yassaa et al: 2008). Because aerosol production of natural origin affects the cloud cover over the open ocean, it is important to investigate the origin of aerosol generation in the open ocean. In this study, we investigated the production of terpenes and isoprene with a focus on Chlamydomonas (Chlorophyceae) and Rhodella maculata (Rhodophyta). Concentrations of terpenes and isoprene were measured using a dynamic headspace (GERSTEL DHS)—gas chromatograph (Agilent 6890N)—mass spectrometer (Agilent 5975C). In addition, chlorophyll a was measured using a fluorometer (Turner TD-700). The results showed that isoprene, α-pinene, and β-pinene were produced by Chlamydomonas sp. and that isoprene, limonene, and camphene were produced by Rhodella maculata. Chlamydomonas sp. produced α-pinene and β-pinene, similar to land plants. The ratio of the pinene/isoprene concentrations in the atmosphere over seawater where phytoplankton are blooming has been reported as approximately 0.7 (Yassaa et al: 2008). In this experiment, the pinene/isoprene concentration ratios in the cultures were approximately 0.1. This result indicates that marine phytoplankton may not be ignored in the marine atmosphere chemistry of terpenes.

Accumulation of γ‐aminobutyric acid by E nterococcus avium 9184 in scallop solution in a two‐stage fermentation strategy

PubMed Central

Yang, Haoyue; Hu, Linfeng; Liu, Song

2015-01-01

Summary In this study, a new bacterial strain having a high ability to produce γ‐aminobutyric acid (GABA) was isolated from naturally fermented scallop solution and was identified as E nterococcus avium. To the best of our knowledge, this is the first study to prove that E . avium possesses glutamate decarboxylase activity. The strain was then mutagenized with UV radiation and was designated as E . avium 9184. Scallop solution was used as the culture medium to produce GABA. A two‐stage fermentation strategy was applied to accumulate GABA. In the first stage, cell growth was regulated. Optimum conditions for cell growth were pH, 6.5; temperature, 37°C; and glucose concentration, 10 g·L−1. This produced a maximum dry cell mass of 2.10 g·L−1. In the second stage, GABA formation was regulated. GABA concentration reached 3.71 g·L−1 at 96 h pH 6.0, 37°C and initial l‐monosodium glutamate concentration of 10 g·L−1. Thus, compared with traditional one‐stage fermentation, the two‐stage fermentation significantly increased GABA accumulation. These results provide preliminary data to produce GABA using E . avium and also provide a new approach to process and utilize shellfish. PMID:26200650

Producing high sugar concentrations from loblolly pine using wet explosion pretreatment.

PubMed

Rana, Diwakar; Rana, Vandana; Ahring, Birgitte K

2012-10-01

We present quantitative analysis of pretreatment for obtaining high conversion and release of sugars from loblolly pine. We use wet explosion (WEx): wet oxidation followed by steam explosion and enzymatic hydrolysis (EH) at high dry matter to solubilize sugars. WEx was conducted at 25% (w/w) solids in presence of oxygen at pressures 6.5-7.2 bar, temperatures 170-175°C and residence time from 20 to 22.5 min. EH of pretreated samples was performed by Cellic® Ctec2 (60 mg protein/g cellulose) and Cellic® Htec2 enzymes (10% of Ctec2) at 50°C for 72 h. At the optimal WEx condition 96% cellulose and nearly 100% hemicellulose yield were obtained. The final concentrations of monomeric sugars were 152 g/L of glucose, 67 g/L of xylose, and 67 g/L of minor sugars (galactose, arabinose and mannose). Compared to previous work WEx seems to be superior for releasing high concentrations of monomeric sugars. Copyright © 2012. Published by Elsevier Ltd.

Dense-array concentrator photovoltaic system using non-imaging dish concentrator and crossed compound parabolic concentrator

NASA Astrophysics Data System (ADS)

Chong, Kok-Keong; Yew, Tiong-Keat; Wong, Chee-Woon; Tan, Ming-Hui; Tan, Woei-Chong; Lai, An-Chow; Lim, Boon-Han; Lau, Sing-Liong; Rahman, Faidz Abdul

2015-04-01

Solar concentrating device plays an important role by making use of optical technology in the design, which can be either reflector or lens to deliver high flux of sunlight onto the Concentrator Photovoltaic (CPV) module receiver ranging from hundreds to thousand suns. To be more competitive compared with fossil fuel, the current CPV systems using Fresnel lens and Parabolic dish as solar concentrator that are widely deployed in United States, Australia and Europe are facing great challenge to produce uniformly focused sunlight on the solar cells as to reduce the cost of electrical power generation. The concept of non-imaging optics is not new, but it has not fully explored by the researchers over the world especially in solving the problem of high concentration solar energy, which application is only limited to be a secondary focusing device or low concentration device using Compound Parabolic Concentrator. With the current advancement in the computer processing power, we has successfully invented the non-imaging dish concentrator (NIDC) using numerical simulation method to replace the current parabolic dish as primary focusing device with high solar concentration ratio (more than 400 suns) and large collective area (from 25 to 125 m2). In this paper, we disclose our research and development on dense array CPV system based on non-imaging optics. The geometry of the NIDC is determined using a special computational method. In addition, an array of secondary concentrators, namely crossed compound parabolic concentrators, is also proposed to further focus the concentrated sunlight by the NIDC onto active area of solar cells of the concentrator photovoltaic receiver. The invention maximizes the absorption of concentrated sunlight for the electric power generation system.

Ice Nucleation and Dehydration in the Tropical Tropopause Layer

NASA Technical Reports Server (NTRS)

Jensen, Eric J.; Diskin, Glenn S.; Lawson, R Paul; Lance, Sara; Bui, Thaopaul Van; Hlavka, Dennis L.; Mcgill, Matthew J.; Pfister, Leonhard; Toon, Owen B.; Gao, Rushan

2013-01-01

Optically thin cirrus near the tropical tropopause regulate the humidity of air entering the stratosphere, which in turn has a strong influence on the Earth's radiation budget and climate. Recent highaltitude, unmanned aircraft measurements provide evidence for two distinct classes of cirrus formed in the tropical tropopause region: (i) vertically extensive cirrus with low ice number concentrations, low extinctions, and large supersaturations (up to approx. 70%) with respect to ice; and (ii) vertically thin cirrus layers with much higher ice concentrations that effectively deplete the vapor in excess of saturation. The persistent supersaturation in the former class of cirrus is consistent with the long time-scales (several hours or longer) for quenching of vapor in excess of saturation given the low ice concentrations and cold tropical tropopause temperatures. The low-concentration clouds are likely formed on a background population of insoluble particles with concentrations less than 100 L-1 (often less than 20 L-1), whereas the high ice concentration layers (with concentrations up to 10,000 L-1) can only be produced by homogeneous freezing of an abundant population of aqueous aerosols. These measurements, along with past high-altitude aircraft measurements, indicate that the low-concentration cirrus occur frequently in the tropical tropopause region, whereas the high-concentration cirrus occur infrequently. The predominance of the low-concentration clouds means cirrus near the tropical tropopause may typically allow entry of air into the stratosphere with as much as approx. 1.7 times the ice saturation mixing ratio.

Paradoxical Growth of Candida albicans in the Presence of Caspofungin Is Associated with Multiple Cell Wall Rearrangements and Decreased Virulence

PubMed Central

Rueda, Cristina; Cuenca-Estrella, Manuel

2014-01-01

In the last decade, echinocandins have emerged as an important family of antifungal drugs because of their fungicidal activity against Candida spp. Echinocandins inhibit the enzyme β-1,3-d-glucan synthase, encoded by the FKS genes, and resistance to echinocandins is associated with mutations in this gene. In addition, echinocandin exposure can produce paradoxical growth, defined as the ability to grow at high antifungal concentrations but not at intermediate concentrations. In this work, we have demonstrated that paradoxical growth of Candida albicans in the presence of caspofungin is not due to antifungal degradation or instability. Media with high caspofungin concentrations recovered from wells where C. albicans showed paradoxical growth inhibited the growth of a Candida krusei reference strain. Cells exhibiting paradoxical growth at high caspofungin concentrations showed morphological changes such as enlarged size, abnormal septa, and absence of filamentation. Chitin content increased from the MIC to high caspofungin concentrations. Despite the high chitin levels, around 23% of cells died after treatment with caspofungin, indicating that chitin is required but not sufficient to protect the cells from the fungicidal effect of caspofungin. Moreover, we found that after paradoxical growth, β-1,3-glucan was exposed at the cell wall surface. Cells grown at high caspofungin concentrations had decreased virulence in the invertebrate host Galleria mellonella. Cells grown at high caspofungin concentrations also induced a proinflammatory response in murine macrophages compared to control cells. Our work highlights important aspects about fungal adaptation to caspofungin, and although this adaptation is associated with reduced virulence, the clinical implications remain to be elucidated. PMID:24295973

Application of Titration-Based Screening for the Rapid Pilot Testing of High-Throughput Assays.

PubMed

Zhang, Ji-Hu; Kang, Zhao B; Ardayfio, Ophelia; Ho, Pei-i; Smith, Thomas; Wallace, Iain; Bowes, Scott; Hill, W Adam; Auld, Douglas S

2014-06-01

Pilot testing of an assay intended for high-throughput screening (HTS) with small compound sets is a necessary but often time-consuming step in the validation of an assay protocol. When the initial testing concentration is less than optimal, this can involve iterative testing at different concentrations to further evaluate the pilot outcome, which can be even more time-consuming. Quantitative HTS (qHTS) enables flexible and rapid collection of assay performance statistics, hits at different concentrations, and concentration-response curves in a single experiment. Here we describe the qHTS process for pilot testing in which eight-point concentration-response curves are produced using an interplate asymmetric dilution protocol in which the first four concentrations are used to represent the range of typical HTS screening concentrations and the last four concentrations are added for robust curve fitting to determine potency/efficacy values. We also describe how these data can be analyzed to predict the frequency of false-positives, false-negatives, hit rates, and confirmation rates for the HTS process as a function of screening concentration. By taking into account the compound pharmacology, this pilot-testing paradigm enables rapid assessment of the assay performance and choosing the optimal concentration for the large-scale HTS in one experiment. © 2013 Society for Laboratory Automation and Screening.

Effect of yeast extract addition to a mineral salts medium containing hydrolyzed plant xylan on fungal pullulan production.

PubMed

Kennedy Ii, Daniel E; West, Thomas P

2018-05-16

The ability of the fungus Aureobasidium pullulans ATCC 42023 to produce pullulan from yeast extract-supplemented xylan hydrolysates of the prairie grass prairie cordgrass was examined relative to polysaccharide and cell biomass production, yield, and pullulan content of the polysaccharide. A pullulan concentration of 11.2 g L-1 and yield of 0.79 g g-1 was produced by ATCC 42023 when grown for 168 h at 30°C on the phosphate-buffered hydrolysate supplemented with yeast extract. The highest biomass level being 8.8 g L-1 was produced by ATCC 42023 after 168 h on a yeast extract-supplemented, hydrolysate-containing complete medium lacking sodium chloride. The highest pullulan content of the polysaccharide produced by ATCC 42023 after 168 h on the hydrolysate medium supplemented with yeast extract and ammonium sulfate was 70%. The findings indicate that a polysaccharide with a high pullulan content can be produced at a relatively high yield by the fungus grown on a yeast extract-supplemented xylan hydrolysate, suggesting that pullulan could be produced using a biomass-based process.

Thermoluminescence (TL) properties and x-ray diffraction (XRD) analysis of high purity CaSO{sub 4}:Dy TL material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kamarudin, Nadira; Abdullah, Wan Saffiey Wan; Dollah, Mohd Taufik

2014-09-03

This paper presents the characterization and TL properties of dysprosium (Dy) doped calcium sulfate (CaSO{sub 4}) TL material produced by co-precipitation technique with 0.5mol% concentration of dopant. The morphology of the produced TL material was studied using scanning electron microscope (SEM) and the micrograph shows that rectangular parallelepiped shaped crystal with the average of 150 μm in length were produced. The crystallinity of the produced powder was studied using x-ray powder diffraction (XRD). The XRD spectra show that the TL material produced is high purity anhydrite CaSO{sub 4} with average crystallite size of 74 nm with orthorhombic crystal system. Themore » TL behavior of produced CaSO{sub 4}:Dy was studied using a TLD reader after exposure to gamma ray by Co{sup 60} source with the doses of 1,5 and 10 Gy. The glow curve shows linear response with glow peak around 230°C which is desired development in the field of radiation dosimetry.« less

Characterization of Catalase from Psychrotolerant Psychrobacter piscatorii T-3 Exhibiting High Catalase Activity

PubMed Central

Kimoto, Hideyuki; Yoshimune, Kazuaki; Matsuyma, Hidetoshi; Yumoto, Isao

2012-01-01

A psychrotolerant bacterium, strain T-3 (identified as Psychrobacter piscatorii), that exhibited an extraordinarily high catalase activity was isolated from the drain pool of a plant that uses H2O2 as a bleaching agent. Its cell extract exhibited a catalase activity (19,700 U·mg protein−1) that was higher than that of Micrococcus luteus used for industrial catalase production. Catalase was approximately 10% of the total proteins in the cell extract of the strain. The catalase (PktA) was purified homogeneously by only two purification steps, anion exchange and hydrophobic chromatographies. The purified catalase exhibited higher catalytic efficiency and higher sensitivity of activity at high temperatures than M. luteus catalase. The deduced amino acid sequence showed the highest homology with catalase of Psycrobacter cryohalolentis, a psychrotolelant bacterium obtained from Siberian permafrost. These findings suggest that the characteristics of the PktA molecule reflected the taxonomic relationship of the isolate as well as the environmental conditions (low temperatures and high concentrations of H2O2) under which the bacterium survives. Strain T-3 efficiently produces a catalase (PktA) at a higher rate than Exiguobacterium oxidotolerans, which produces a very strong activity of catalase (EktA) at a moderate rate, in order to adapt to high concentration of H2O2. PMID:22408420

The effect of microchannel plate gain depression on PAPA photon counting cameras

NASA Astrophysics Data System (ADS)

Sams, Bruce J., III

1991-03-01

PAPA (precision analog photon address) cameras are photon counting imagers which employ microchannel plates (MCPs) for image intensification. They have been used extensively in astronomical speckle imaging. The PAPA camera can produce artifacts when light incident on its MCP is highly concentrated. The effect is exacerbated by adjusting the strobe detection level too low, so that the camera accepts very small MCP pulses. The artifacts can occur even at low total count rates if the image has highly a concentrated bright spot. This paper describes how to optimize PAPA camera electronics, and describes six techniques which can avoid or minimize addressing errors.

Highly selective fluorescence turn-on sensor for fluoride detection.

PubMed

Sui, Binglin; Kim, Bosung; Zhang, Yuanwei; Frazer, Andrew; Belfield, Kevin D

2013-04-24

Through click chemistry, triazole and triazolium groups have been explored to recognize anions through C-H···A(-) hydrogen-bonding complexion. Herein, we demonstrate evidence of fluoride-induced deprotonation of a C-H bond and its application in fluoride detection. The combination of fluorene and triazolium units produced a highly selective fluorescence turn-on prototype sensor for fluoride. The interactions between the C-H bond and F(-) were studied by fluorescence spectroscopy and (1)H NMR titrations. Test papers were prepared to detect fluoride in aqueous media at concentrations down to 1.9 ppm, important for estimating whether the fluoride concentration in drinking water is at a safe level.

Micro-PIXE evaluation of radioactive cesium transfer in contaminated soil samples

NASA Astrophysics Data System (ADS)

Fujishiro, F.; Ishii, K.; Matsuyama, S.; Arai, H.; Ishizaki, A.; Osada, N.; Sugai, H.; Kusano, K.; Nozawa, Y.; Yamauchi, S.; Karahashi, M.; Oshikawa, S.; Kikuchi, K.; Koshio, S.; Watanabe, K.; Suzuki, Y.

2014-01-01

Micro-PIXE analysis has been performed on two soil samples with high cesium activity concentrations. These soil samples were contaminated by fallout from the accident at Fukushima Daiichi Nuclear Power Plant. One exhibits a radioactive cesium transfer of ˜0.01, and the other shows a radioactive cesium transfer of less than 0.001, even though both samples have high cesium activity concentrations exceeding 10,000 Bq/kg. X-ray spectra and elemental images of the soil samples revealed the presence of chlorine, which can react with cesium to produce an inorganic soluble compound, and phosphorus-containing cesium-capturable organic compounds.

Competitive light absorbers in photoactive dental resin-based materials.

PubMed

Hadis, Mohammed A; Shortall, Adrian C; Palin, William M

2012-08-01

The absorbance profile of photoinitiators prior to, during and following polymerization of light curable resin-based materials will have a significant effect on the cure and color properties of the final material. So-called "colorless" photoinitiators are used in some light-activated resin-based composite restorative materials to lessen the yellowing effect of camphoroquinone (CQ) in order to improve the esthetic quality of dental restorations. This work characterizes absorption properties of commonly used photoinitiators, an acylphosphine oxide (TPO) and CQ, and assesses their influence on material discoloration. Dimethacrylate resin formulations contained low (0.0134 mol/dm(3)), intermediate (0.0405 mol/dm(3)) or high (0.0678 mol/dm(3)) concentrations of the photoinitiators and the inhibitor, butylated hydroxytoluene (BHT) at 0, 0.1 or 0.2% by mass. Disc shaped specimens (n = 3) of each resin were polymerized for 60s using a halogen light curing unit. Dynamic measurements of photoinitiator absorption, polymer conversion and reaction temperature were performed. A spectrophotometer was used to measure the color change before and after cure. GLM three-way analysis of variance revealed significant differences (p<0.001), where photoinitiator concentration (df = 2; F = 618.83)>photoinitiator type (df = 1; F = 176.12)>% BHT (df = 2, F = 13.17). BHT concentration affected the rate of polymerization and produced lower conversion in some of the CQ-based resins. Significant differences between photoinitiator type and concentrations were seen in color (where TPO resins became yellower and camphoroquinone resins became less yellow upon irradiation). Reaction temperature, kinetics and conversion also differed significantly for both initiators (p<0.001). Despite TPO-based resins producing a visually perceptible color change upon polymerization, the color change was significantly less than that produced with CQ-based resins. Although some photoinitiators such as TPO may be a more esthetic alternative to CQ, they may actually cause significant color contamination when used in high concentrations and therefore manufacturers should limit its concentration in order to improve its esthetic quality. Copyright © 2012 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

A Laser Spark Plug Ignition System for a Stationary Lean-Burn Natural Gas Reciprocating Engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

McIntyre, D. L.

To meet the ignition system needs of large bore, high pressure, lean burn, natural gas engines a side pumped, passively Q-switched, Nd:YAG laser was developed and tested. The laser was designed to produce the optical intensities needed to initiate ignition in a lean burn, high compression engine. The laser and associated optics were designed with a passive Q-switch to eliminate the need for high voltage signaling and associated equipment. The laser was diode pumped to eliminate the need for high voltage flash lamps which have poor pumping efficiency. The independent and dependent parameters of the laser were identified and exploredmore » in specific combinations that produced consistent robust sparks in laboratory air. Prior research has shown that increasing gas pressure lowers the breakdown threshold for laser initiated ignition. The laser has an overall geometry of 57x57x152 mm with an output beam diameter of approximately 3 mm. The experimentation used a wide range of optical and electrical input parameters that when combined produced ignition in laboratory air. The results show a strong dependence of the output parameters on the output coupler reflectivity, Q-switch initial transmission, and gain media dopant concentration. As these three parameters were lowered the output performance of the laser increased leading to larger more brilliant sparks. The results show peak power levels of up to 3MW and peak focal intensities of up to 560 GW/cm 2. Engine testing was performed on a Ricardo Proteus single cylinder research engine. The goal of the engine testing was to show that the test laser performs identically to the commercially available flashlamp pumped actively Q-switched laser used in previous laser ignition testing. The engine testing consisted of a comparison of the in-cylinder, and emissions behavior of the engine using each of the lasers as an ignition system. All engine parameters were kept as constant as possilbe while the equivalence ratio (fueling), and hence the engine load, was varied between 0.8, 0.9, and 1.0. The test laser was constructed with a 30% output coupler, 32% Q-switch initial transmission, and a 0.5% Nd concentration rod all pumped by approximately 1000 Watts of optical power. The test laser single mode output pulse had an energy of approximately 23 mJ, with a pulsewidth of approximately 10 ns, and an M2 value of 6.55. This output produced focal intensity of approximately 270 GW/cm 2 with the modified on-engine optical arrangement. The commercial laser had similar output parameters and both laser systems operated the engine with similar results. Due to the shortening of the focal length of the on-engine optical setup both laser systems produced a spark well within the optical transfer cavity of the laser optics to spark plug adaptor. This shrouded spark led to a very long ignition delay and retarded combustion timing for all three values of equivalence ratio. This was evidenced by the in-cylinder pressure traces and the HRR waveforms. The emissions data indicate that both lasers produced very similar combustion. The ignition delay caused by the shrouded spark cause most of the combustion to happen after TDC which lead to poor combustion that produced high levels of CO and THC. The novelty of this work lies in the combination of the laser parameters to create a single high peak power laser output pulse for use as a spark ignition source. Similar configurations have been investigated in the literature but for different applications such as multiple output pulse trains for various industrial and communications applications. Another point of novelty is the investigation of the laser medium concentration on the output characteristics of a passively Q-switched laser system. This work has shown that lowering the Neodymium concentration in the active media within a passively Q-switched laser produces higher output energy values. This is significant because an actively Q-switched laser shows the opposite affect when the active ion concentration is varied.« less

The effect of plum juice on the prevention of struvite calculus formation in vitro.

PubMed

Zhu, Huaijun; Sun, Xizhao; Lu, Jianlin; Wang, Meihua; Fang, Yun; Ge, Weihong

2012-10-01

To evaluate the effect of plum juice on struvite calculus formation in vitro and to explore the effect of plum juice on urease-producing bacteria and urease activity. The compliance of available drugs is low for struvite calculus after surgical treatment and functional food may represent a good choice as an alternative therapy. Antibacterial activity was assessed using a microdilution antimicrobial susceptibility test. Urease activity was determined by measuring ammonia production. Struvite crystals were induced by Proteus mirabilis in artificial urine with natural and pH-adjusted plum juice. The optical density (OD)(600) and pH of artificial urine were examined, as well the shape and weights of crystals. Natural plum juice showed an antibacterial effect on urease-producing bacteria, whereas the pH-adjusted juice did not. A concentration-dependent inhibition on urease activity was found for both natural and pH-adjusted juice. Natural plum juice at a high concentration of 0.5% showed an obvious inhibition on the increase of OD(600) and pH of the artificial urine, and crystal formation was prevented by up to or more than 8 h, depending on the concentration of juice. Crystal weight in the natural plum juice groups was decreased in a concentration-dependent manner. The pH-adjusted plum juice did not show any effect on OD(600) and pH, although the presence of juice changed the crystal habit, indicating that the juice slowed the growth rate of crystals. Natural plum juice at high and moderate concentrations prevented the formation of P. mirabilis-induced crystals for up to 8 h in artificial urine. Although pH-adjusted and low-concentration natural juice did not prevent the occurrence of crystals, both types of juice slowed their growth rate.

Enhanced electrocatalytic CO2 reduction via field-induced reagent concentration

NASA Astrophysics Data System (ADS)

Liu, Min; Pang, Yuanjie; Zhang, Bo; de Luna, Phil; Voznyy, Oleksandr; Xu, Jixian; Zheng, Xueli; Dinh, Cao Thang; Fan, Fengjia; Cao, Changhong; de Arquer, F. Pelayo García; Safaei, Tina Saberi; Mepham, Adam; Klinkova, Anna; Kumacheva, Eugenia; Filleter, Tobin; Sinton, David; Kelley, Shana O.; Sargent, Edward H.

2016-09-01

Electrochemical reduction of carbon dioxide (CO2) to carbon monoxide (CO) is the first step in the synthesis of more complex carbon-based fuels and feedstocks using renewable electricity. Unfortunately, the reaction suffers from slow kinetics owing to the low local concentration of CO2 surrounding typical CO2 reduction reaction catalysts. Alkali metal cations are known to overcome this limitation through non-covalent interactions with adsorbed reagent species, but the effect is restricted by the solubility of relevant salts. Large applied electrode potentials can also enhance CO2 adsorption, but this comes at the cost of increased hydrogen (H2) evolution. Here we report that nanostructured electrodes produce, at low applied overpotentials, local high electric fields that concentrate electrolyte cations, which in turn leads to a high local concentration of CO2 close to the active CO2 reduction reaction surface. Simulations reveal tenfold higher electric fields associated with metallic nanometre-sized tips compared to quasi-planar electrode regions, and measurements using gold nanoneedles confirm a field-induced reagent concentration that enables the CO2 reduction reaction to proceed with a geometric current density for CO of 22 milliamperes per square centimetre at -0.35 volts (overpotential of 0.24 volts). This performance surpasses by an order of magnitude the performance of the best gold nanorods, nanoparticles and oxide-derived noble metal catalysts. Similarly designed palladium nanoneedle electrocatalysts produce formate with a Faradaic efficiency of more than 90 per cent and an unprecedented geometric current density for formate of 10 milliamperes per square centimetre at -0.2 volts, demonstrating the wider applicability of the field-induced reagent concentration concept.

Modelling and analysis of ozone concentration by artificial intelligent techniques for estimating air quality

NASA Astrophysics Data System (ADS)

Taylan, Osman

2017-02-01

High ozone concentration is an important cause of air pollution mainly due to its role in the greenhouse gas emission. Ozone is produced by photochemical processes which contain nitrogen oxides and volatile organic compounds in the lower atmospheric level. Therefore, monitoring and controlling the quality of air in the urban environment is very important due to the public health care. However, air quality prediction is a highly complex and non-linear process; usually several attributes have to be considered. Artificial intelligent (AI) techniques can be employed to monitor and evaluate the ozone concentration level. The aim of this study is to develop an Adaptive Neuro-Fuzzy inference approach (ANFIS) to determine the influence of peripheral factors on air quality and pollution which is an arising problem due to ozone level in Jeddah city. The concentration of ozone level was considered as a factor to predict the Air Quality (AQ) under the atmospheric conditions. Using Air Quality Standards of Saudi Arabia, ozone concentration level was modelled by employing certain factors such as; nitrogen oxide (NOx), atmospheric pressure, temperature, and relative humidity. Hence, an ANFIS model was developed to observe the ozone concentration level and the model performance was assessed by testing data obtained from the monitoring stations established by the General Authority of Meteorology and Environment Protection of Kingdom of Saudi Arabia. The outcomes of ANFIS model were re-assessed by fuzzy quality charts using quality specification and control limits based on US-EPA air quality standards. The results of present study show that the ANFIS model is a comprehensive approach for the estimation and assessment of ozone level and is a reliable approach to produce more genuine outcomes.

Biomineralisation by earthworms - an investigation into the stability and distribution of amorphous calcium carbonate.

PubMed

Hodson, Mark E; Benning, Liane G; Demarchi, Bea; Penkman, Kirsty E H; Rodriguez-Blanco, Juan D; Schofield, Paul F; Versteegh, Emma A A

Many biominerals form from amorphous calcium carbonate (ACC), but this phase is highly unstable when synthesised in its pure form inorganically. Several species of earthworm secrete calcium carbonate granules which contain highly stable ACC. We analysed the milky fluid from which granules form and solid granules for amino acid (by liquid chromatography) and functional group (by Fourier transform infrared (FTIR) spectroscopy) compositions. Granule elemental composition was determined using inductively coupled plasma-optical emission spectroscopy (ICP-OES) and electron microprobe analysis (EMPA). Mass of ACC present in solid granules was quantified using FTIR and compared to granule elemental and amino acid compositions. Bulk analysis of granules was of powdered bulk material. Spatially resolved analysis was of thin sections of granules using synchrotron-based μ-FTIR and EMPA electron microprobe analysis. The milky fluid from which granules form is amino acid-rich (≤ 136 ± 3 nmol mg -1 (n = 3; ± std dev) per individual amino acid); the CaCO 3 phase present is ACC. Even four years after production, granules contain ACC. No correlation exists between mass of ACC present and granule elemental composition. Granule amino acid concentrations correlate well with ACC content (r ≥ 0.7, p ≤ 0.05) consistent with a role for amino acids (or the proteins they make up) in ACC stabilisation. Intra-granule variation in ACC (RSD = 16%) and amino acid concentration (RSD = 22-35%) was high for granules produced by the same earthworm. Maps of ACC distribution produced using synchrotron-based μ-FTIR mapping of granule thin sections and the relative intensity of the ν 2 : ν 4 peak ratio, cluster analysis and component regression using ACC and calcite standards showed similar spatial distributions of likely ACC-rich and calcite-rich areas. We could not identify organic peaks in the μ-FTIR spectra and thus could not determine whether ACC-rich domains also had relatively high amino acid concentrations. No correlation exists between ACC distribution and elemental concentrations determined by EMPA. ACC present in earthworm CaCO 3 granules is highly stable. Our results suggest a role for amino acids (or proteins) in this stability. We see no evidence for stabilisation of ACC by incorporation of inorganic components. Graphical abstractSynchrotron-based μ-FTIR mapping was used to determine the spatial distribution of amorphous calcium carbonate in earthworm-produced CaCO 3 granules.

Factors affecting the behavior of unburned carbon upon steam activation

NASA Astrophysics Data System (ADS)

Lu, Zhe

The main objective of this study is to investigate the factors that could affect the behavior of unburned carbon samples upon steam activation. Through this work, the relationships among the factors that could influence the carbon-steam reaction with the surface area of the produced activated carbon were explored. Statistical analysis was used to relate the chemical and physical properties of the unburned carbon to the surface area of the activated carbon. Six unburned carbons were selected as feedstocks for activated carbon, and marked as UCA through UCF. The unburned carbons were activated using steam at 850°C for 90 minutes, and the surface areas of their activated counterparts were measured using N2 adsorption isotherms at 77K. The activated carbons produced from different unburned carbon precursors presented different surface areas at similar carbon burn-off levels. Moreover, in different carbon burn-off regions, the sequences for surface area of activated carbons from different unburned carbon samples were different. The factors that may affect the carbon-steam gasification reactions, including the concentration of carbon active sites, the crystallite size of the carbon, the intrinsic porous structure of carbon, and the inorganic impurities, were investigated. All unburned carbons investigated in this study were similar in that they showed the very broad (002) and (10 ) carbon peaks, which are characteristic of highly disordered carbonaceous materials. In this study, the unburned carbon samples contained about 17--48% of inorganic impurities. Compared to coals, the unburned carbon samples contain a larger amount of inorganic impurities as a result of the burn-off, or at lease part, of the carbon during the combustion process. These inorganic particles were divided into two groups in terms of the way they are associated with carbon particles: free single particles, and particles combined with carbon particles. As indicated from the present work, unburned carbons with one of the following properties will produce activated carbons with high surface areas. These properties include: (a) large amount of O2 chemisorption capacity; (b) high concentration of surface C-O complex; and (c) small crystallite diameter; (d) high concentration of Na+K particles that are combined with carbon; (e) high concentration of isotropic carbon. (Abstract shortened by UMI.)

Effect of protein degradability on milk production of dairy ewes.

PubMed

Mikolayunas-Sandrock, C; Armentano, L E; Thomas, D L; Berger, Y M

2009-09-01

The objective of this experiment was to determine the effect of protein degradability of dairy sheep diets on milk yield and protein utilization across 2 levels of milk production. Three diets were formulated to provide similar energy concentrations and varying concentrations of rumen-degradable protein (RDP) and rumen-undegradable protein (RUP): 12% RDP and 4% RUP (12-4) included basal levels of RDP and RUP, 12% RDP and 6% RUP (12-6) included additional RUP, and 14% RDP and 4% RUP (14-4) included additional RDP. Diets were composed of alfalfa-timothy cubes, whole and ground corn, whole oats, dehulled soybean meal, and expeller soybean meal (SoyPlus, West Central, Ralston, IA). Estimates of RDP and RUP were based on the Small Ruminant Nutrition System model (2008) and feed and orts were analyzed for Cornell N fractions. Eighteen multiparous dairy ewes in midlactation were divided by milk yield (low and high) into 2 blocks of 9 ewes each and were randomly assigned within block (low and high) to 3 pens of 3 ewes each. Dietary treatments were arranged in a 3 x 3 Latin square within each block and applied to pens for 14-d periods. We hypothesized that pens consuming high-RUP diets (12-6) would produce more milk and milk protein than the basal diet (12-4) and pens consuming high-RDP diets (14-4) would not produce more milk than the basal diet (12-4). Ewes in the high-milk-yield square consumed more dry matter and produced more milk, milk fat, and milk protein than ewes in the low-milk-yield square. There was no effect of dietary treatment on dry matter intake. Across both levels of milk production, the 12-6 diet increased milk yield by 14%, increased milk fat yield by 14%, and increased milk protein yield by 13% compared with the 14-4 and 12-4 diets. Gross N efficiency (milk protein N/intake protein N) was 11 and 15% greater in the 12-6 and 12-4 diets, respectively, compared with the 14-4 diet. Milk urea N concentration was greater in the 12-6 diet and tended to be greater in the 14-4 diet compared with the 12-4 diet, indicating that the excretion of urea N in this study was more closely related to dietary crude protein concentration than to protein degradability.

Engineering of a Novel Saccharomyces cerevisiae Wine Strain with a Respiratory Phenotype at High External Glucose Concentrations

PubMed Central

Henricsson, C.; de Jesus Ferreira, M. C.; Hedfalk, K.; Elbing, K.; Larsson, C.; Bill, R. M.; Norbeck, J.; Hohmann, S.; Gustafsson, L.

2005-01-01

The recently described respiratory strain Saccharomyces cerevisiae KOY.TM6*P is, to our knowledge, the only reported strain of S. cerevisiae which completely redirects the flux of glucose from ethanol fermentation to respiration, even at high external glucose concentrations (27). In the KOY.TM6*P strain, portions of the genes encoding the predominant hexose transporter proteins, Hxt1 and Hxt7, were fused within the regions encoding transmembrane (TM) domain 6. The resulting chimeric gene, TM6*, encoded a chimera composed of the amino-terminal half of Hxt1 and the carboxy-terminal half of Hxt7. It was subsequently integrated into the genome of an hxt null strain. In this study, we have demonstrated the transferability of this respiratory phenotype to the V5 hxt1-7Δ strain, a derivative of a strain used in enology. We also show by using this mutant that it is not necessary to transform a complete hxt null strain with the TM6* construct to obtain a non-ethanol-producing phenotype. The resulting V5.TM6*P strain, obtained by transformation of the V5 hxt1-7Δ strain with the TM6* chimeric gene, produced only minor amounts of ethanol when cultured on external glucose concentrations as high as 5%. Despite the fact that glucose flux was reduced to 30% in the V5.TM6*P strain compared with that of its parental strain, the V5.TM6*P strain produced biomass at a specific rate as high as 85% that of the V5 wild-type strain. Even more relevant for the potential use of such a strain for the production of heterologous proteins and also of low-alcohol beverages is the observation that the biomass yield increased 50% with the mutant compared to its parental strain. PMID:16204537

Engineering of a novel Saccharomyces cerevisiae wine strain with a respiratory phenotype at high external glucose concentrations.

PubMed

Henricsson, C; de Jesus Ferreira, M C; Hedfalk, K; Elbing, K; Larsson, C; Bill, R M; Norbeck, J; Hohmann, S; Gustafsson, L

2005-10-01

The recently described respiratory strain Saccharomyces cerevisiae KOY.TM6*P is, to our knowledge, the only reported strain of S. cerevisiae which completely redirects the flux of glucose from ethanol fermentation to respiration, even at high external glucose concentrations (27). In the KOY.TM6*P strain, portions of the genes encoding the predominant hexose transporter proteins, Hxt1 and Hxt7, were fused within the regions encoding transmembrane (TM) domain 6. The resulting chimeric gene, TM6*, encoded a chimera composed of the amino-terminal half of Hxt1 and the carboxy-terminal half of Hxt7. It was subsequently integrated into the genome of an hxt null strain. In this study, we have demonstrated the transferability of this respiratory phenotype to the V5 hxt1-7Delta strain, a derivative of a strain used in enology. We also show by using this mutant that it is not necessary to transform a complete hxt null strain with the TM6* construct to obtain a non-ethanol-producing phenotype. The resulting V5.TM6*P strain, obtained by transformation of the V5 hxt1-7Delta strain with the TM6* chimeric gene, produced only minor amounts of ethanol when cultured on external glucose concentrations as high as 5%. Despite the fact that glucose flux was reduced to 30% in the V5.TM6*P strain compared with that of its parental strain, the V5.TM6*P strain produced biomass at a specific rate as high as 85% that of the V5 wild-type strain. Even more relevant for the potential use of such a strain for the production of heterologous proteins and also of low-alcohol beverages is the observation that the biomass yield increased 50% with the mutant compared to its parental strain.

Studies on the preparation and uses of Co-60 gamma-ray irradiated natural latex

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kartowardoyo, S.; Sundardi, F.

1977-11-01

The properties are described of low-ammonia latex concentrates produced by gamma-ray irradiation (0.5 to 2.0 Mrad dose) in the presence of carbon tetrachloride or chloroform as sensitizer. Dipping trails with irradiated concentrates and irradiated field latex, for the preparation of condoms and medical gloves, gave products with high ultimate elongation, low modulus, and high permanent set. A change from straight dipping to coagulant dipping and a heat treatment after drying resulted in improved physical properties. A notable feature of products prepared from these materials is their purity, i.e., low content of rubber chemicals. An economic disadvantage, at the present time,more » is the high initial cost of the irradiation equipment.« less

WETLAND INVERTEBRATE COMMUNITY RESPONSES TO VARYING EMERGENT LITTER IN A PRAIRIE POTHOLE EMERGENT MARSH

EPA Science Inventory

Plant litter produced in the interior of dense emergent stands may directly or indirectly influence invertebrate communities. Low litter may provide structure and refuge to invertebrates while high litter may shade out vegetation and algae and decrease oxygen concentrations. With...

ARSENIC DETERMINATION IN SALINE WATERS BY HYDRIDE GENERATION - INDUCTIVELY COUPLED PLASMA MASS SPECTROMETRY.

EPA Science Inventory

The determination of arsenic in estuarine waters usually involves a matrix removal and/or pre-concentration prior to analysis because of the high salt content in these waters. The salinity also produces analytical challenges in terms of interferences and instrument stability. A...

New bimetallic EMF cell shows promise in direct energy conversion

NASA Technical Reports Server (NTRS)

Hesson, J. C.; Shimotake, H.

1968-01-01

Concentration cell, based upon a thermally regenerative cell principle, produces electrical energy from any large heat source. This experimental bimetallic EMF cell uses a sodium-bismuth alloy cathode and a pure liquid sodium anode. The cell exhibits reliability, corrosion resistance, and high current density performance.

HIGH BREVETOXIN CONCENTRATIONS IN GYMNODINIUM BREVE BLOOMS ALONG THE NORTHWEST FLORIDA COAST DURING 1999.

EPA Science Inventory

Blooms of the dinoflagellate Gymnodinium breve (i.e. red tides) produce brevetoxins (PbTx) that negatively impact the Gulf of Mexico ecosystem, human health, and local economics. Characterizing and predicting bloom events and their impacts requires knowledge of G. breve abundance...

Proteomic analyses of ethanol tolerance in Lactobacillus buchneri NRRL B-30929

USDA-ARS?s Scientific Manuscript database

The Lactobacillus buchneri NRRL B-30929 strain, isolated from a fuel ethanol production facility, exhibits high tolerance to environmental ethanol concentrations. This study aimed to identify proteins produced by B-30929 in response to environmental ethanol. Cellular proteins expressed by B-30929 gr...

HIGH BREVETOXIN CONCENTRATIONS IN GYMNODINIUM BREVE BLOOMS ALONG THE NORTHWEST FLORIDA COAST DURING 1999

EPA Science Inventory

Blooms of the dinoflagellate Gymnodinium breve (i.e. red tides) produce brevetoxins (PbTx) that negatively impact the Gulf of Mexico ecosystem, human health, and local economics. Characterizing and predicting bloom events and their impacts requires knowledge of G. breve abundance...

Color Blind

ERIC Educational Resources Information Center

Reid, Karla Scoon

2004-01-01

This article talks about a colorblind plan that the Charlotte-Mecklenburg school district adopted for student assignment in 2002 that is producing more racially isolated schools, like Selwyn Elementary School, and more schools enrolling high concentrations of poor children. The 2-year-old plan gives parents a choice of schools and provides all…

Synthesis of soybean oil-based thiol oligomers.

PubMed

Wu, Jennifer F; Fernando, Shashi; Weerasinghe, Dimuthu; Chen, Zhigang; Webster, Dean C

2011-08-22

Industrial grade soybean oil (SBO) and thiols were reacted to generate thiol-functionalized oligomers via a thermal, free radical initiated thiol-ene reaction between the SBO double bond moieties and the thiol functional groups. The effect of the reaction conditions, including thiol concentration, catalyst loading level, reaction time, and atmosphere, on the molecular weight and the conversion to the resultant soy-thiols were examined in a combinatorial high-throughput fashion using parallel synthesis, combinatorial FTIR, and rapid gel permeation chromatography (GPC). High thiol functionality and concentration, high thermal free radical catalyst concentration, long reaction time, and the use of a nitrogen reaction atmosphere were found to favor fast consumption of the SBO, and produced high molecular weight products. The thiol conversion during the reaction was inversely affected by a high thiol concentration, but was favored by a long reaction time and an air reaction atmosphere. These experimental observations were explained by the initial low affinity of the SBO and thiol, and the improved affinity between the generated soy-thiol oligomers and unreacted SBO during the reaction. The synthesized soy-thiol oligomers can be used for renewable thiol-ene UV curable materials and high molecular solids and thiourethane thermal cure materials. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Alloy nanoparticle synthesis using ionizing radiation

DOEpatents

Nenoff, Tina M [Sandia Park, NM; Powers, Dana A [Albuquerque, NM; Zhang, Zhenyuan [Durham, NC

2011-08-16

A method of forming stable nanoparticles comprising substantially uniform alloys of metals. A high dose of ionizing radiation is used to generate high concentrations of solvated electrons and optionally radical reducing species that rapidly reduce a mixture of metal ion source species to form alloy nanoparticles. The method can make uniform alloy nanoparticles from normally immiscible metals by overcoming the thermodynamic limitations that would preferentially produce core-shell nanoparticles.

Highly thermal-stable and functional cellulose nanocrystals and nanofibrils produced using fully recyclable organic acids

Treesearch

Liheng Chen; Junyong Zhu; Carlos Baez; Peter Kitin; Thomas Elder

2016-01-01

Here we report the production of highly thermal stable and functional cellulose nanocrystals (CNC) and nanofibrils (CNF) by hydrolysis using concentrated organic acids. Due to their low water solubility, these solid organic acids can be easily recovered after hydrolysis reactions through crystallization at a lower or ambient temperature. When dicarboxylic acids were...

Direct fired reciprocating engine and bottoming high temperature fuel cell hybrid

DOEpatents

Geisbrecht, Rodney A [New Alexandria, PA; Holcombe, Norman T [McMurray, PA

2006-02-07

A system of a fuel cell bottoming an internal combustion engine. The engine exhaust gas may be combined in varying degrees with air and fed as input to a fuel cell. Reformer and oxidizers may be combined with heat exchangers to accommodate rich and lean burn conditions in the engine in peaking and base load conditions without producing high concentrations of harmful emissions.

Interaction of Ochratoxin A and Its Thermal Degradation Product 2'R-Ochratoxin A with Human Serum Albumin.

PubMed

Sueck, Franziska; Poór, Miklós; Faisal, Zelma; Gertzen, Christoph G W; Cramer, Benedikt; Lemli, Beáta; Kunsági-Máté, Sándor; Gohlke, Holger; Humpf, Hans-Ulrich

2018-06-22

Ochratoxin A (OTA) is a toxic secondary metabolite produced by several fungal species of the genus Penicillium and Aspergillus . 2′ R -Ochratoxin A (2′ R -OTA) is a thermal isomerization product of OTA formed during food processing at high temperatures. Both compounds are detectable in human blood in concentrations between 0.02 and 0.41 µg/L with 2′ R -OTA being only detectable in the blood of coffee drinkers. Humans have approximately a fifty-fold higher exposure through food consumption to OTA than to 2′ R -OTA. In human blood, however, the differences between the concentrations of the two compounds is, on average, only a factor of two. To understand these unexpectedly high 2′ R -OTA concentrations found in human blood, the affinity of this compound to the most abundant protein in human blood the human serum albumin (HSA) was studied and compared to that of OTA, which has a well-known high binding affinity. Using fluorescence spectroscopy, equilibrium dialysis, circular dichroism (CD), high performance affinity chromatography (HPAC), and molecular modelling experiments, the affinities of OTA and 2′ R -OTA to HSA were determined and compared with each other. For the affinity of HSA towards OTA, a log K of 7.0⁻7.6 was calculated, while for its thermally produced isomer 2′ R -OTA, a lower, but still high, log K of 6.2⁻6.4 was determined. The data of all experiments showed consistently that OTA has a higher affinity to HSA than 2′ R -OTA. Thus, differences in the affinity to HSA cannot explain the relatively high levels of 2′ R -OTA found in human blood samples.

Biogenic production of cyanide and its application to gold recovery.

PubMed

Campbell, S C; Olson, G J; Clark, T R; McFeters, G

2001-03-01

Chromobacterium violaceum is a cyanogenic (cyanide-producing) microorganism. Cyanide is used on an industrial scale to complex and recover gold from ores or concentrates of ores bearing the precious metal. A potentially useful approach in gold mining operations could be to produce cyanide biologically in relatively small quantities at the ore surface. In this study, C. violaceum grown in nutrient broth formed a biofilm and could complex and solubilize 100% of the gold on glass test slides within 4-7 days. Approximately 50% of the cyanide- recoverable gold could be mobilized from a biooxidized sulfidic-ore concentrate. Complexation of cyanide in solution by gold appeared to have a beneficial effect on cell growth--viable cell counts were nearly two orders of magnitude greater in the presence of gold-coated slides or biooxidized ore substrates than in their absence. C. violaceum was cyanogenic when grown in alternative feedstocks. When grown in a mineral salt solution supplemented with 13.3% v/v swine fecal material (SFM), cells exhibited pigmentation and suspended cell concentrations comparable to cultures grown in nutrient broth. Glycine supplements stimulated production of cyanide in 13.3% v/v SFM. In contrast, glycine was inhibitory when added at the time of inoculation in the more concentrated SFM, decreasing cell numbers and reducing ultimate bulk-solution cyanide concentrations. However, aeration and addition of glycine to stationary phase cells grown on 13.3% v/v SFM anaerobically resulted in rapid production and high concentrations (up to 38 mg l(-1)) of cyanide. This indicates that biogenesis of cyanide may be supported in remote areas using locally produced and inexpensive agricultural feedstocks in place of commercial media.

Alternative Sodium Recovery Technology—High Hydroxide Leaching: FY10 Status Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mahoney, Lenna A.; Neiner, Doinita; Peterson, Reid A.

2011-02-04

Boehmite leaching tests were carried out at NaOH concentrations of 10 M and 12 M, temperatures of 85°C and 60°C, and a range of initial aluminate concentrations. These data, and data obtained during earlier 100°C tests using 1 M and 5 M NaOH, were used to establish the dependence of the boehmite dissolution rate on hydroxide concentration, temperature, and initial aluminate concentration. A semi-empirical kinetic model for boehmite leaching was fitted to the data and used to calculate the NaOH additions required for leaching at different hydroxide concentrations. The optimal NaOH concentration for boehmite leaching at 85°C was estimated, basedmore » on minimizing the amount of Na that had to be added in NaOH to produce a given boehmite conversion.« less

Simulation of solidification in a Bridgman cell

NASA Technical Reports Server (NTRS)

Dakhoul, Y. M.; Farmer, R. C.

1984-01-01

Bridgman-type crystal growth techniques are attractive methods for producing homogeneous, high-quality infrared detector and junction device materials. However, crystal imperfections and interface shapes still must be controlled through modification of the temperature and concentration gradients created during solidification. The objective of this investigation was to study the temperature fields generated by various cell and heatpipe configurations and operating conditions. Continuum's numerical model of the temperature, species concentrations, and velocity fields was used to describe the thermal characteristics of Bridgman cell operation.

Structural properties of iron and nickel mixed oxide nano particles.

NASA Astrophysics Data System (ADS)

Dehipawala, Sunil; Samarasekara, Pubudu; Gafney, Harry

Small scale magnets have very high technological importance today. Instead of traditional expensive methods, scientists are exploring new low cost methods to produce micro magnets. We synthesized thin film magnets containing iron and nickel oxides. Films will be synthesized using sol-gel method and spin coating technique. Several different precursor concentrations were tested to find out the ideal concentrations for stable thin films. Structural properties of iron and nickel oxide particles were investigated using X-ray absorption and Mossbauer spectroscopy. PSC-CUNY.

Dispersion of nanosized ceramic powders in aqueous suspensions

NASA Astrophysics Data System (ADS)

Chera, L.; Palcevskis, E.; Berzins, M.; Lipe, A.; Jansone, I.

2007-12-01

Seven commercially available dispersants have been applied to produce high concentrated aqueous suspensions of the nanosized alumina and partially stabilized zirconia powders processed by the plasma technique. Simultaneously, the electrokinetic behaviour of powders has been investigated in diluted suspensions by microelectrophoresis method. Zeta potential measurements are used to estimate the influence of selected dispersants on the electrokinetic properties of the powder surface. On the basis of obtained data the correlation between the surface electrokinetic properties in dilute suspensions and reached maximal suspension concentration is discussed.

Submerged culture conditions for the production of mycelial biomass and antimicrobial metabolites by Polyporus tricholoma Mont.

PubMed Central

Vieira, Gladys Rosane Thomé; Liebl, Mariane; Tavares, Lorena Benathar Ballod; Paulert, Roberta; Smânia Júnior, Artur

2008-01-01

Basidiomycete fungi of the Polyporus genus are a source of secondary metabolites which are of medicinal interest as antibacterial compounds. As these substances are produced in a small amount by the fungi, the study of the cultivation conditions in vitro that could possibly optimize their production seems of major importance. The effects of glucose and lactose, pH and agitation on biomass concentration and on the specific growth rate caused by the basidiomycete Polyporus tricholoma were investigated. The initial pH (4.5, 6.5 and 8.5) was autoregulated at pH 5.5, and the agitation increased the mycelial growth and the specific growth rate. The high concentration of carbon sources (4%) increased biomass production. The lactose concentration and the absence of agitation were determinant in the production of antibacterial metabolites. The characterization of the antibacterial substance by GC-MS indicated a major compound, isodrimenediol, produced by the fungus Polyporus tricholoma with activity against Staphylococcus aureus. PMID:24031266

Estimating suspended sediment concentrations in turbid coastal waters of the Santa Barbara Channel with SeaWiFS

USGS Publications Warehouse

Warrick, J.A.; Mertes, L.A.K.; Siegel, D.A.; Mackenzie, C.

2004-01-01

A technique is presented for estimating suspended sediment concentrations of turbid coastal waters with remotely sensed multi-spectral data. The method improves upon many standard techniques, since it incorporates analyses of multiple wavelength bands (four for Sea-viewing Wide Field of view Sensor (SeaWiFS)) and a nonlinear calibration, which produce highly accurate results (expected errors are approximately ±10%). Further, potential errors produced by erroneous atmospheric calibration in excessively turbid waters and influences of dissolved organic materials, chlorophyll pigments and atmospheric aerosols are limited by a dark pixel subtraction and removal of the violet to blue wavelength bands. Results are presented for the Santa Barbara Channel, California where suspended sediment concentrations ranged from 0–200+ mg l−1 (±20 mg l−1) immediately after large river runoff events. The largest plumes were observed 10–30 km off the coast and occurred immediately following large El Niño winter floods.

Characterization and biological activities of extracellular melanin produced by Schizophyllum commune (Fries).

PubMed

Arun, G; Eyini, M; Gunasekaran, P

2015-06-01

Melanins are enigmatic pigments produced by a wide variety of microorganisms including bacteria and fungi. Here, we have isolated and characterized extracellular melanin from mushroom fungus, Schizophyllum commune. The extracellular dark pigment produced by the broth culture of S. commune, after 21 days of incubation was recovered by hot acid-alkali treatment. The melanin nature of the pigment was characterized by biochemical tests and further, confirmed by UV, IR, EPR, NMR and MALDI-TOF Mass Spectra. Extracellular melanin, at 100 μg/ml, showed significant antibacterial activity against Escherichia coli, Bacillus subtilis, Klebsiella pneumoniae and Pseudomonas fluorescens and antifungal activity against Trichophyton simii and T. rubrum. At a concentration of 50 μg/ml, melanin showed high free radical scavenging activity of DPPH (2,2-diphenyl-1-picrylhydrazyl) indicating its antioxidant potential. It showed concentration dependent inhibition of cell proliferation of Human Epidermoid Larynx Carcinoma Cell Line (HEP-2). This study has demonstrated characterization of melanin from basidiomycetes mushroom fungus, Schizophyllum commune and its applications.

City scale pollen concentration variability

NASA Astrophysics Data System (ADS)

van der Molen, Michiel; van Vliet, Arnold; Krol, Maarten

2016-04-01

Pollen are emitted in the atmosphere both in the country-side and in cities. Yet the majority of the population is exposed to pollen in cities. Allergic reactions may be induced by short-term exposure to pollen. This raises the question how variable pollen concentration in cities are in temporally and spatially, and how much of the pollen in cities are actually produced in the urban region itself. We built a high resolution (1 × 1 km) pollen dispersion model based on WRF-Chem to study a city's pollen budget and the spatial and temporal variability in concentration. It shows that the concentrations are highly variable, as a result of source distribution, wind direction and boundary layer mixing, as well as the release rate as a function of temperature, turbulence intensity and humidity. Hay Fever Forecasts based on such high resolution emission and physical dispersion modelling surpass traditional hay fever warning methods based on temperature sum methods. The model gives new insights in concentration variability, personal and community level exposure and prevention. The model will be developped into a new forecast tool to serve allergic people to minimize their exposure and reduce nuisance, coast of medication and sick leave. This is an innovative approach in hay fever warning systems.

Physiological and Biochemical Changes Imposed by CeO2 Nanoparticles on Wheat: A Life Cycle Field Study.

PubMed

Du, Wenchao; Gardea-Torresdey, Jorge L; Ji, Rong; Yin, Ying; Zhu, Jianguo; Peralta-Videa, Jose R; Guo, Hongyan

2015-10-06

Interactions of nCeO2 with plants have been mostly evaluated at seedling stage and under controlled conditions. In this study, the effects of nCeO2 at 0 (control), 100 (low), and 400 (high) mg/kg were monitored for the entire life cycle (about 7 months) of wheat plants grown in a field lysimeter. Results showed that at high concentration nCeO2 decreased the chlorophyll content and increased catalase and superoxide dismutase activities, compared with control. Both concentrations changed root and leaf cell microstructures by agglomerating chromatin in nuclei, delaying flowering by 1 week, and reduced the size of starch grains in endosperm. Exposed to low concentration produced embryos with larger vacuoles, while exposure to high concentration reduced number of vacuoles, compared with control. There were no effects on the final biomass and yield, Ce concentration in shoots, as well as sugar and starch contents in grains, but grain protein increased by 24.8% and 32.6% at 100 and 400 mg/kg, respectively. Results suggest that more field life cycle studies are needed in order to better understand the effects of nCeO2 in crop plants.

Planar waveguide concentrator used with a seasonal tracker.

PubMed

Bouchard, Sébastien; Thibault, Simon

2012-10-01

Solar concentrators offer good promise for reducing the cost of solar power. Planar waveguides equipped with a microlens slab have already been proposed as an excellent approach to produce medium to high concentration levels. Instead, we suggest the use of a cylindrical microlens array to get useful concentration without tracking during the day. To use only a seasonal tracking system and get the highest possible concentration, cylindrical microlenses are placed in the east-west orientation. Our new design has an acceptance angle in the north-south direction of ±9° and ±54° in the east-west axis. Simulation of our optimized system achieves a 4.6× average concentration level from 8:30 to 16:30 with a maximum of 8.1× and 80% optical efficiency. The low-cost advantage of waveguide-based solar concentrators could support their use in roof-mounted solar panels and eliminate the need for an expensive and heavy active tracker.

Survival of bactericidal antibiotic treatment by tolerant persister cells of Klebsiella pneumoniae.

PubMed

Li, Ying; Zhang, Luhua; Zhou, Yingshun; Zhang, Zhikun; Zhang, Xinzhuo

2018-03-01

Persister cells, a subpopulation of tolerant cells within the bacterial culture, are commonly thought to be responsible for antibiotic therapy failure and infection recurrence. Klebsiella pneumoniae is a notorious human pathogen for its increasing resistance to antibiotics and wide involvement in severe infections. In this study, we aimed to investigate the persister subpopulation of K. pneumoniae. The presence of persisters in K. pneumoniae was determined by treatment with high concentrations of antibiotics, used alone or in combination. The effect of low level of antibiotics on persister formation was investigated by pre-exposure of cells to antibiotics with low concentrations followed by higher doses. The dependence of persister levels on growth phase was determined by measuring the survival ability of cells along the growth stages upon exposure to a high concentration of antibiotic. Analysis on persister type was carried out by persister elimination assays.Results/Key findings. We show that K. pneumoniae produces high levels of tolerant persister cells to survive treatment by a variety of high concentrations of bactericidal antibiotics and persister formation is prevalent among K. pneumoniae clinical strains. Besides, we find that persister cells can be induced by low concentrations of antibiotics. Finally, we provide evidence that persister formation is growth phase-dependent and Type II persisters dominate the persister subpopulation during the entire exponential phase of K. pneumoniae. Our study describes the formation of tolerant persister cells that allow survival of treatment by high concentrations of antibiotics in K. pneumoniae.

Silica extraction from geothermal water

DOEpatents

Bourcier, William L; Bruton, Carol J

2014-09-23

A method of producing silica from geothermal fluid containing low concentration of the silica of less than 275 ppm includes the steps of treating the geothermal fluid containing the silica by reverse osmosis treatment thereby producing a concentrated fluid containing the silica, seasoning the concentrated fluid thereby producing a slurry having precipitated colloids containing the silica, and separating the silica from the slurry.

Comparison of common lignin methods and modifications on forage and lignocellulosic biomass materials.

PubMed

Goff, Ben M; Murphy, Patrick T; Moore, Kenneth J

2012-03-15

A variety of methods have been developed for estimating lignin concentration within plant materials. The objective of this study was to compare the lignin concentrations produced by six methods on a diverse population of forage and biomass materials and to examine the relationship between these concentrations and the portions of these materials that are available for utilisation by livestock or for ethanol conversion. Several methods produced lignin concentrations that were highly correlated with the digestibility of the forages, but there were few relationships between these methods and the available carbohydrate of the biomass materials. The use of Na₂SO₃ during preparation of residues for hydrolysis resulted in reduced lignin concentrations and decreased correlation with digestibility of forage materials, particularly the warm-season grasses. There were several methods that were well suited for predicting the digestible portion of forage materials, with the acid detergent lignin and Klason lignin method giving the highest correlation across the three types of forage. The continued use of Na₂SO₃ during preparation of Van Soest fibres needs to be evaluated owing to its ability to reduce lignin concentrations and effectiveness in predicting the utilisation of feedstuffs and feedstocks. Because there was little correlation between the lignin concentration and the biomass materials, there is a need to examine alternative or develop new methods to estimate lignin concentrations that may be used to predict the availability of carbohydrates for ethanol conversion. Copyright © 2011 Society of Chemical Industry.

High yield fabrication of fluorescent nanodiamonds

PubMed Central

Boudou, Jean-Paul; Curmi, Patrick; Jelezko, Fedor; Wrachtrup, Joerg; Aubert, Pascal; Sennour, Mohamed; Balasubramanian, Gopalakrischnan; Reuter, Rolf; Thorel, Alain; Gaffet, Eric

2009-01-01

A new fabrication method to produce homogeneously fluorescent nanodiamonds with high yields is described. The powder obtained by high energy ball milling of fluorescent high pressure, high temperature diamond microcrystals was converted in a pure concentrated aqueous colloidal dispersion of highly crystalline ultrasmall nanoparticles with a mean size less than or equal to 10 nm. The whole fabrication yield of colloidal quasi-spherical nanodiamonds was several orders of magnitude higher than those previously reported starting from microdiamonds. The results open up avenues for the industrial cost-effective production of fluorescent nanodiamonds with well-controlled properties. PMID:19451687

Controlling the size of alginate gel beads by use of a high electrostatic potential.

PubMed

Klokk, T I; Melvik, J E

2002-01-01

The effect of several parameters on the size of alginate beads produced by use of an electrostatic potential bead generator was examined. Parameters studied included needle diameter, electrostatic potential, alginate solution flow rate, gelling ion concentration and alginate concentration and viscosity, as well as alginate composition. Bead size was found to decrease with increasing electrostatic potential, but only down to a certain level. Minimum bead size was reached at between 2-4 kV/cm for the needles tested. The smallest alginate beads produced (using a needle with inner diameter 0.18 mm) had a mean diameter of approximately 300 microm. Bead size was also found to be dependent upon the flow rate of the fed alginate solution. Increasing the gelling ion concentration resulted in a moderate decrease in bead size. The concentration and viscosity of the alginate solution also had an effect on bead size as demonstrated by an increased bead diameter when the concentration or viscosity was increased. This effect was primarily an effect of the viscosity properties of the solution, which led to changes in the rate of droplet formation in the bead generator. Lowering the flow rate of the alginate solution could partly compensate for the increase in bead size with increased viscosity. For a constant droplet size, alginates with a low G block content (F(GG) approximately 0.20) resulted in approximately 30% smaller beads than alginates with a high G block content (F(GG) approximately 0.60). This is explained as a result of differences in the shrinking properties of the beads.

Inhibition of the acetoclastic methanogenic activity by phenol and alkyl phenols.

PubMed

Olguin-Lora, P; Puig-Grajales, L; Razo-Flores, E

2003-08-01

Chemical and petrochemical industries are important sources of aromatic pollutants. Petrochemical processes like caustic washing of middle distillates produce the spent caustic liquors highly concentrated in phenol and alkyl phenols. The anaerobic technology is considered a feasible strategy for petrochemical wastewater pre-treatment although high concentrations of phenol could limit its efficiency. The goal of this work was to determine the toxicity of both selected alkyl phenols and a synthetic "spent-caustic phenols mixture" on the acetoclastic Specific Methanogenic Activity (SMA) of unadapted and phenol-adapted granular sludge. Alkyl phenols were responsible for 50% (IC50) and 100% (IC100) inhibition of the SMA at concentrations ranging from 1.6 to 5.0 mM and from 4.1 to 27.5 mM, respectively, for un-adapted granular sludge. In the case of phenol-adapted granular sludge, the inhibitory concentrations ranged from 1.7 to 14.9 mM and from 4.0 to 83.0 for IC50 and IC100, respectively, highlighting the impact of sludge acclimation. The inhibition produced by 2-ethylphenol was more acute compared to phenol and was not reduced by the phenol acclimation process. The IC50 and IC100 values obtained for the synthetic "spent-caustic phenols mixture" were 9.5 mM and 88.4 mM, respectively. The inhibitory concentrations of phenol compounds were closely correlated with compound apolarity (log P), indicating that the lipophilic character of the tested compounds was responsible for their methanogenic toxicity. An inhibition model is confirmed to estimate the IC50 and IC100.

The implementation of high fermentative 2,3-butanediol production from xylose by simultaneous additions of yeast extract, Na2EDTA, and acetic acid.

PubMed

Wang, Xiao-Xiong; Hu, Hong-Ying; Liu, De-Hua; Song, Yuan-Quan

2016-01-25

The effective use of xylose may significantly enhance the feasibility of using lignocellulosic hydrolysate to produce 2,3-butanediol (2,3-BD). Previous difficulties in 2,3-BD production include that the high-concentration xylose cannot be converted completely and the fermentation rate is slow. This study investigated the effects of yeast extract, ethylenediaminetetraacetic acid disodium salt (Na2EDTA), and acetic acid on 2,3-BD production from xylose. The central composite design approach was used to optimize the concentrations of these components. It was found that simultaneous addition of yeast extract, Na2EDTA, and acetic acid could significantly improve 2,3-BD production. The optimal concentrations of yeast extract, Na2EDTA, and acetic acid were 35.2, 1.2, and 4.5 g/L, respectively. The 2,3-BD concentration in the optimized medium reached 39.7 g/L after 48 hours of shake flask fermentation, the highest value ever reported in such a short period. The xylose utilization ratio and the 2,3-BD concentration increased to 99.0% and 42.7 g/L, respectively, after 48 hours of stirred batch fermentation. Furthermore, the 2,3-BD yield was 0.475 g/g, 95.0% of the theoretical maximum value. As the major components of lignocellulosic hydrolysate are glucose, xylose, and acetic acid, the results of this study indicate the possibility of directly using the hydrolysate to effectively produce 2,3-BD. Copyright © 2015 Elsevier B.V. All rights reserved.

Conceptual design of a self-deployable, high performance parabolic concentrator for advanced solar-dynamic power systems

NASA Astrophysics Data System (ADS)

Dehne, Hans J.

1991-05-01

NASA has initiated technology development programs to develop advanced solar dynamic power systems and components for space applications beyond 2000. Conceptual design work that was performed is described. The main efforts were the: (1) conceptual design of self-deploying, high-performance parabolic concentrator; and (2) materials selection for a lightweight, shape-stable concentrator. The deployment concept utilizes rigid gore-shaped reflective panels. The assembled concentrator takes an annular shape with a void in the center. This deployable concentrator concept is applicable to a range of solar dynamic power systems of 25 kW sub e to in excess of 75 kW sub e. The concept allows for a family of power system sizes all using the same packaging and deployment technique. The primary structural material selected for the concentrator is a polyethyl ethylketone/carbon fiber composite also referred to as APC-2 or Vitrex. This composite has a nearly neutral coefficient of thermal expansion which leads to shape stable characteristics under thermal gradient conditions. Substantial efforts were undertaken to produce a highly specular surface on the composite. The overall coefficient of thermal expansion of the composite laminate is near zero, but thermally induced stresses due to micro-movement of the fibers and matrix in relation to each other cause the surface to become nonspecular.

Hierarchical Cluster Formation in Concentrated Monoclonal Antibody Formulations

NASA Astrophysics Data System (ADS)

Godfrin, P. Douglas; Zarzar, Jonathan; Zarraga, Isidro Dan; Porcar, Lionel; Falus, Peter; Wagner, Norman; Liu, Yun

Reversible cluster formation has been identified as an underlying cause of large solution viscosities observed in some concentrated monoclonal antibody (mAb) formulations. As high solution viscosity prevents the use of subcutaneous injection as a delivery method for some mAbs, a fundamental understanding of the interactions responsible for high viscosities in concentrated mAb solutions is of significant relevance to mAb applications in human health care as well as of intellectual interest. Here, we present a detailed investigation of a well-studied IgG1 based mAb to relate the short time dynamics and microstructure to significant viscosity changes over a range of pharmaceutically relevant physiochemical conditions. Using a combination of experimental techniques, it is found that upon adding Na2SO4, these antibodies dimerize in solution. Proteins form strongly bounded reversible dimers at dilute concentrations that, when concentrated, interact with each other to form loosely bounded, large, transient clusters. The combined effect of forming strongly bounded dimers and a large transient network is a significant increase in the solution viscosity. Strongly bounded, reversible dimers may exist in many IgG1 based mAb systems such that these results contribute to a more comprehensive understanding of the physical mechanisms producing high viscosities in concentrated protein solutions.

Conceptual design of a self-deployable, high performance parabolic concentrator for advanced solar-dynamic power systems

NASA Technical Reports Server (NTRS)

Dehne, Hans J.

1991-01-01

NASA has initiated technology development programs to develop advanced solar dynamic power systems and components for space applications beyond 2000. Conceptual design work that was performed is described. The main efforts were the: (1) conceptual design of self-deploying, high-performance parabolic concentrator; and (2) materials selection for a lightweight, shape-stable concentrator. The deployment concept utilizes rigid gore-shaped reflective panels. The assembled concentrator takes an annular shape with a void in the center. This deployable concentrator concept is applicable to a range of solar dynamic power systems of 25 kW sub e to in excess of 75 kW sub e. The concept allows for a family of power system sizes all using the same packaging and deployment technique. The primary structural material selected for the concentrator is a polyethyl ethylketone/carbon fiber composite also referred to as APC-2 or Vitrex. This composite has a nearly neutral coefficient of thermal expansion which leads to shape stable characteristics under thermal gradient conditions. Substantial efforts were undertaken to produce a highly specular surface on the composite. The overall coefficient of thermal expansion of the composite laminate is near zero, but thermally induced stresses due to micro-movement of the fibers and matrix in relation to each other cause the surface to become nonspecular.

Mycotoxin production in wheat grains by different Aspergilli in relation to different relative humidities and storage periods.

PubMed

Atalla, Mohamed Mabrouk; Hassanein, Naziha Mohamed; El-Beih, Ahmed Atef; Youssef, Youssef Abdel-ghany

2003-02-01

Four different Aspergilli (Aspergillus oryzae, A. parasiticus, A. terreus and A. versicolor) were grown on wheat grains underdifferent degrees of relative humidity 14, 50, 74, 80 and 90%. Samples of wheat grains were taken monthly for a period of six months and examined for mycotoxin production. A. oryzae was found to produce aflatoxins B1, B2, zearalenone, DON and T-2 toxins under elevated degrees of humidity and prolonged periods of storage. A. parasiticus produced aflatoxins B1, G1, NIV, DON and T-2 toxins in high concentrations during a period of not more than three months storage at 14% relative humidity; at an increased level of relative humidity of 74% ochratoxin A, zearalenone and sterigmatocystin were also produced at high levels. The isolate was drastic in toxin production. A. terrus produced toxins at 14% relative humidity (aflatoxin G2 and DON) at levels much higher than any other prevalent degrees of humidity. A. versicolor is highly sensitive to relative humidity and grain moisture content It produced aflatoxins B1, G1, NIV and DON at a relative humidity of 50% and another toxins (aflatoxin G2, ochratoxins A, B and zearalenone) at 74%. The microorganism can be considered a trichothecene producer under suitable relative humidity.

Removal of high concentration p-nitrophenol in aqueous solution by zero valent iron with ultrasonic irradiation (US-ZVI).

PubMed

Lai, Bo; Chen, Zhaoyu; Zhou, Yuexi; Yang, Ping; Wang, Juling; Chen, Zhiqiang

2013-04-15

In this study, the US-ZVI system was used to produce the strong reductants including H and nascent Fe(2+) ions to eliminate the toxicity of the high concentration p-nitrophenol (PNP) wastewater. The effect of the reactor structure, initial pH, ZVI dosage, ultrasonic power and initial PNP concentration on the removal efficiency of PNP from water was investigated intensively. The results show that a higher removal rate can be obtained by using a conical structure reactor, and the lower initial pH can aid the acceleration of PNP removal rate by using US-ZVI system. Furthermore, the removal efficiencies of PNP increased obviously with the increase of initial ZVI concentration from 0 to 15 gL(-1). Also, the treatment capacity of ZVI was enhanced remarkably by the ultrasonic irradiation, and the US-ZVI system can maintain high treatment efficiency for the high concentration PNP wastewater (500-10,000 mgL(-1)). Meanwhile, the high removal efficiency of PNP was mainly resulted from the synergistic reaction of ZVI and US. At last, the main degradation product (i.e., p-aminophenol) was detected by gas chromatography-mass spectrum (GC-MS). Thus, the reaction pathway of PNP in the US-ZVI system is proposed as a reducing process by the H and nascent Fe(2+) ions. Copyright © 2013 Elsevier B.V. All rights reserved.

Reduction of extended-spectrum-β-lactamase- and AmpC-β-lactamase-producing Escherichia coli through processing in two broiler chicken slaughterhouses.

PubMed

Pacholewicz, Ewa; Liakopoulos, Apostolos; Swart, Arno; Gortemaker, Betty; Dierikx, Cindy; Havelaar, Arie; Schmitt, Heike

2015-12-23

Whilst broilers are recognised as a reservoir of extended-spectrum-β-lactamase (ESBL)- and AmpC-β-lactamase (AmpC)-producing Escherichia coli, there is currently limited knowledge on the effect of slaughtering on its concentrations on poultry meat. The aim of this study was to establish the concentration of ESBL/AmpC producing E. coli on broiler chicken carcasses through processing. In addition the changes in ESBL/AmpC producing E. coli concentrations were compared with generic E. coli and Campylobacter. In two slaughterhouses, the surface of the whole carcasses was sampled after 5 processing steps: bleeding, scalding, defeathering, evisceration and chilling. In total, 17 batches were sampled in two different slaughterhouses during the summers of 2012 and 2013. ESBL/AmpC producing E. coli was enumerated on MacConkey agar with 1mg/l cefotaxime, and the ESBL/AmpC phenotypes and genotypes were characterised. The ESBL/AmpC producing E. coli concentrations varied significantly between the incoming batches in both slaughterhouses. The concentrations on broiler chicken carcasses were significantly reduced during processing. In Slaughterhouse 1, all subsequent processing steps reduced the concentrations except evisceration which led to a slight increase that was statistically not significant. The changes in concentration between processing steps were relatively similar for all sampled batches in this slaughterhouse. In contrast, changes varied between batches in Slaughterhouse 2, and the overall reduction through processing was higher in Slaughterhouse 2. Changes in ESBL/AmpC producing E. coli along the processing line were similar to changes in generic E. coli in both slaughterhouses. The effect of defeathering differed between ESBL/AmpC producing E. coli and Campylobacter. ESBL/AmpC producing E. coli decreased after defeathering, whereas Campylobacter concentrations increased. The genotypes of ESBL/AmpC producing E. coli (blaCTX-M-1, blaSHV-12, blaCMY-2, blaTEM-52c, blaTEM-52cvar) from both slaughterhouses match typical poultry genotypes. Their distribution differed between batches and changed throughout processing for some batches. The concentration levels found after chilling were between 10(2) and 10(5)CFU/carcass. To conclude, changes in ESBL/AmpC producing E. coli concentrations on broiler chicken carcasses during processing are influenced by batch and slaughterhouse, pointing to the role of both primary production and process control for reducing ESBL/AmpC producing E. coli levels in final products. Due to similar changes upon processing, E. coli can be used as a process indicator of ESBL/AmpC producing E. coli, because the processing steps had similar impact on both organisms. Cross contamination may potentially explain shifts in genotypes within some batches through the processing. Copyright © 2015 Elsevier B.V. All rights reserved.

Solar concentrator modules with silicone-onglass Fresnel lens panels and multijunction cells.

PubMed

Rumyantsev, Valery D

2010-04-26

High-efficiency multijunction (MJ) solar cells, being very expensive to manufacture, should only be used in combination with solar concentrators in terrestrial applications. An essential cost reduction of electric power produced by photovoltaic (PV) installations with MJ cells, may be expected by the creation of highly-effective, but inexpensive, elements for optical concentration and sun tracking. This article is an overview of the corresponding approach under development at the Ioffe Physical Technical Institute. The approach to R&D of the solar PV modules is based on the concepts of sunlight concentration by small-aperture area Fresnel lenses and "all-glass" module design. The small-aperture area lenses are arranged as a panel with silicone-on-glass structure where the glass plate serves as the front surface of a module. In turn, high-efficiency InGaP/(In)GaAs/Ge cells are arranged on a rear module panel mounted on a glass plate which functions as a heat sink and integrated protective cover for the cells. The developed PV modules and sun trackers are characterized by simple design, and are regarded as the prototypes for further commercialization.

Pathogenesis of lead shot poisoning in the mallard duck

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clemens, E.T.; Krook, L.; Aronson, A.L.

1975-04-01

Adult mallard ducks were administered steel pellets to determine the rate of excretion from the gastrointestinal tract. In separate studies the ducks were administered 5 number 6 lead pellets. Birds were examined for clinical signs and sacrificed at given intervals over a 20 day period to assess changes in tissue structure and concentrations of lead with time. The rate of steel pellet excretion on birds on a low fiber diet decreased with an increase in pellet size. Pellet excretion was greatly reduced in birds fed a high fiber diet. Administration of lead shot resulted in the development of green diarrhea,more » anorexia and weakness. It also produced high concentrations of lead in the blood, kidney, liver and bone with lower concentrations in skeletal muscle. The major lesions were destruction of the mitotically active proventricular epithelium and medullary osteocytes, destruction of pectoral muscle cells and the presence of intranuclear inclusion bodies in the proximal tubular epithelium of the kidney. Birds on the high fiber diet demonstrated more severe clinical signs and higher concentrations of lead in the tissues.« less

Integrated microfluidic system with simultaneous emulsion generation and concentration.

PubMed

Koppula, Karuna S; Fan, Rong; Veerapalli, Kartik R; Wan, Jiandi

2016-03-15

Because the size, size distribution, and concentration of emulsions play an important role in most of the applications, controlled emulsion generation and effective concentration are of great interest in fundamental and applied studies. While microfluidics has been demonstrated to be able to produce emulsion drops with controlled size, size distribution, and hierarchical structures, progress of controlled generation of concentrated emulsions is limited. Here, we present an effective microfluidic emulsion generation system integrated with an orifice structure to separate aqueous droplets from the continuous oil phase, resulting in concentrated emulsion drops in situ. Both experimental and simulation results show that the efficiency of separation is determined by a balance between pressure drop and droplet accumulation near the orifice. By manipulating this balance via changing flow rates and microfluidic geometry, we can achieve monodisperse droplets on chip that have a concentration as high as 80,000 drops per microliter (volume fraction of 66%). The present approach thus provides insights to the design of microfluidic device that can be used to concentrate emulsions (drops and bubbles), colloidal particles (drug delivery polymer particles), and biological particles (cells and bacteria) when volume fractions as high as 66% are necessary. Copyright © 2015 Elsevier Inc. All rights reserved.

Occurrence of perfluoroalkyl substances (PFAS) in garden produce at homes with a history of PFAS-contaminated drinking water.

PubMed

Scher, Deanna P; Kelly, James E; Huset, Carin A; Barry, Kitrina M; Hoffbeck, Richard W; Yingling, Virginia L; Messing, Rita B

2018-04-01

The decades-long disposal of manufacturing waste containing perfluoroalkyl substances (PFAS) in landfills resulted in contamination of groundwater serving as the drinking water supply for the eastern Twin Cities metropolitan region. While measures were taken to reduce the levels of PFAS in the drinking water, questions remained about possible non-drinking water pathways of exposure in these communities. The Minnesota Department of Health (MDH) investigated whether PFAS in water used for yard and garden irrigation results in elevated concentrations of PFAS in soil and home-grown produce. In 2010, samples of outdoor tap water, garden soil, and garden produce were collected at homes impacted by the contamination and analyzed for several PFAS. Perfluorobutanoic acid (PFBA) was the primary PFAS present in water, followed by perfluoropentanoic acid (PFPeA). Although PFBA, perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) were present in 100% of soil samples at higher concentrations compared to other PFAS, only PFBA was readily translocated to plants. Significant determinants of PFBA concentration in produce were the amount of PFBA applied to the garden via watering and the type of produce tested. Results from this real-world study are consistent with experimental findings that short-chain PFAS have the highest potential to translocate to and bioaccumulate in edible plants. These findings are globally relevant, as short-chain PFAS serve as commercial substitutes for longer-chain compounds and are increasingly detected in water due to their relatively high solubility and mobility. Copyright © 2018 Elsevier Ltd. All rights reserved.

Fermentative utilization of glycerol residue for the production of acetic acid

NASA Astrophysics Data System (ADS)

Irvan; Trisakti, B.; Hasibuan, R.; Joli, M.

2018-02-01

Glycerol residue, frequently known as pitch, is a waste produced from the downstream product of crude glycerine distillation. With the increasing need of pure glycerine in the world, the glycerol residue produced is also increasing. Glycerol residue is a solid waste at room temperature, highly alkaline (pH > 13), corrosive, and categorized as hazardous and poisonous waste. In this research, acetic acid was produced from glycerol residue through the anaerobic fermentation process by using purple non-sulphur photosynthetic bacteria. The purpose of this study was to find out the influence of concentration change of glycerol residue on time and to find out the possibility of glycerol residue to be utilized as acetic acid. In this research, at first 400 g of glycerol residue was diluted with 200 ml of distilled water to change the glycerine phase, from solid to liquid at room temperature, acidified by using hydrochloric acid until pH 2. The top layer formed was fatty acid and triglycerides that should be removed. Meanwhile, the bottom layer was diluted glycerol residue which was then neutralized with caustic soda. To produce acetic acid, glycerol residue with various concentrations, salt, and purple non-sulphur photosynthetic bacteria were put together into a 100 ml bottle which had been previously sterilized, then incubated for four weeks under the light of 40-watt bulb. The result showed that on the 28th day of fermentation, the produced acetic acid were 0.28, 1.85, and 0.2% (w/w) by using glycerine with the concentration of 0.5, 1.0, and 1.5% (w/w), respectively.

Effects of temperature and gas-liquid mass transfer on the operation of small electrochemical cells for the quantitative evaluation of CO2 reduction electrocatalysts.

PubMed

Lobaccaro, Peter; Singh, Meenesh R; Clark, Ezra Lee; Kwon, Youngkook; Bell, Alexis T; Ager, Joel W

2016-09-29

In the last few years, there has been increased interest in electrochemical CO 2 reduction (CO2R). Many experimental studies employ a membrane separated, electrochemical cell with a mini H-cell geometry to characterize CO2R catalysts in aqueous solution. This type of electrochemical cell is a mini-chemical reactor and it is important to monitor the reaction conditions within the reactor to ensure that they are constant throughout the study. We show that operating cells with high catalyst surface area to electrolyte volume ratios (S/V) at high current densities can have subtle consequences due to the complexity of the physical phenomena taking place on electrode surfaces during CO2R, particularly as they relate to the cell temperature and bulk electrolyte CO 2 concentration. Both effects were evaluated quantitatively in high S/V cells using Cu electrodes and a bicarbonate buffer electrolyte. Electrolyte temperature is a function of the current/total voltage passed through the cell and the cell geometry. Even at a very high current density, 20 mA cm -2 , the temperature increase was less than 4 °C and a decrease of <10% in the dissolved CO 2 concentration is predicted. In contrast, limits on the CO 2 gas-liquid mass transfer into the cells produce much larger effects. By using the pH in the cell to measure the CO 2 concentration, significant undersaturation of CO 2 is observed in the bulk electrolyte, even at more modest current densities of 10 mA cm -2 . Undersaturation of CO 2 produces large changes in the faradaic efficiency observed on Cu electrodes, with H 2 production becoming increasingly favored. We show that the size of the CO 2 bubbles being introduced into the cell is critical for maintaining the equilibrium CO 2 concentration in the electrolyte, and we have designed a high S/V cell that is able to maintain the near-equilibrium CO 2 concentration at current densities up to 15 mA cm -2 .

Effects of temperature and gas–liquid mass transfer on the operation of small electrochemical cells for the quantitative evaluation of CO 2 reduction electrocatalysts

DOE PAGES

Lobaccaro, Peter; Singh, Meenesh R.; Clark, Ezra Lee; ...

2016-09-06

In the last few years, there has been increased interest in electrochemical CO 2 reduction (CO2R). Many experimental studies employ a membrane separated, electrochemical cell with a mini H-cell geometry to characterize CO2R catalysts in aqueous solution. This type of electrochemical cell is a mini-chemical reactor and it is important to monitor the reaction conditions within the reactor to ensure that they are constant throughout the study. Here we show that operating cells with high catalyst surface area to electrolyte volume ratios (S/V) at high current densities can have subtle consequences due to the complexity of the physical phenomena takingmore » place on electrode surfaces during CO2R, particularly as they relate to the cell temperature and bulk electrolyte CO 2 concentration. Both effects were evaluated quantitatively in high S/V cells using Cu electrodes and a bicarbonate buffer electrolyte. Electrolyte temperature is a function of the current/total voltage passed through the cell and the cell geometry. Even at a very high current density, 20 mA cm -2 , the temperature increase was less than 4 °C and a decrease of < 10% in the dissolved CO 2 concentration is predicted. In contrast, limits on the CO 2 gas-liquid mass transfer into the cells produce much larger effects. By using the pH in the cell to measure the CO 2 concentration, significant undersaturation of CO 2 is observed in the bulk electrolyte, even at more modest current densities of 10 mA cm -2 . Undersaturation of CO 2 produces large changes in the faradaic efficiency observed on Cu electrodes, with H 2 production becoming increasingly favored. Finally, we show that the size of the CO 2 bubbles being introduced into the cell is critical for maintaining the equilibrium CO 2 concentration in the electrolyte, and we have designed a high S/V cell that is able to maintain the near-equilibrium CO 2 concentration at current densities up to 15 mA cm -2.« less

Effects of temperature and gas–liquid mass transfer on the operation of small electrochemical cells for the quantitative evaluation of CO 2 reduction electrocatalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lobaccaro, Peter; Singh, Meenesh R.; Clark, Ezra Lee

In the last few years, there has been increased interest in electrochemical CO 2 reduction (CO2R). Many experimental studies employ a membrane separated, electrochemical cell with a mini H-cell geometry to characterize CO2R catalysts in aqueous solution. This type of electrochemical cell is a mini-chemical reactor and it is important to monitor the reaction conditions within the reactor to ensure that they are constant throughout the study. Here we show that operating cells with high catalyst surface area to electrolyte volume ratios (S/V) at high current densities can have subtle consequences due to the complexity of the physical phenomena takingmore » place on electrode surfaces during CO2R, particularly as they relate to the cell temperature and bulk electrolyte CO 2 concentration. Both effects were evaluated quantitatively in high S/V cells using Cu electrodes and a bicarbonate buffer electrolyte. Electrolyte temperature is a function of the current/total voltage passed through the cell and the cell geometry. Even at a very high current density, 20 mA cm -2 , the temperature increase was less than 4 °C and a decrease of < 10% in the dissolved CO 2 concentration is predicted. In contrast, limits on the CO 2 gas-liquid mass transfer into the cells produce much larger effects. By using the pH in the cell to measure the CO 2 concentration, significant undersaturation of CO 2 is observed in the bulk electrolyte, even at more modest current densities of 10 mA cm -2 . Undersaturation of CO 2 produces large changes in the faradaic efficiency observed on Cu electrodes, with H 2 production becoming increasingly favored. Finally, we show that the size of the CO 2 bubbles being introduced into the cell is critical for maintaining the equilibrium CO 2 concentration in the electrolyte, and we have designed a high S/V cell that is able to maintain the near-equilibrium CO 2 concentration at current densities up to 15 mA cm -2.« less

The effect of isoenzyme-selective PDE inhibitors on methacholine-induced contraction of guinea-pig and rat ileum.

PubMed Central

Tomkinson, A.; Raeburn, D.

1996-01-01

1. We have examined the effects of the isoenzyme-selective phosphodiesterase (PDE) inhibitors, vinpocetine (type 1), siguazodan (type 3), rolipram (type 4) and zaprinast (type 5) and the non-selective PDE inhibitor enprofylline on methacholine (MCh) contractile concentration-response curves on guinea-pig and rat isolated ileum. 2. In guinea-pig ileum, vinpocetine (10-300 microM), zaprinast (1-300 microM) and enprofylline (100-1000 microM) produced a concentration-dependent depression of the maximum response (Emax) to MCh only without effect on the MCh EC50 values (rank order of potency: zaprinast > vinpocetine > enprofylline). In contrast, siguazodan (10-300 microM) and rolipram (10-300 microM) produced a rightward displacement of the MCh concentration-response curve (increase in EC50: rank order; rolipram > siguazodan), with effects on the MCh maximum seen only at higher concentrations. 3. In the rat ileum, vinpocetine (10-300 microM), zaprinast (0.1-300 microM) and enprofylline (100-1000 microM) caused depression of the MCh maximum contraction (rank order: zaprinast > vinpocetine > enprofylline). Low concentrations of rolipram and siguazodan had no significant effect on the MCh maximum. In the presence of higher concentrations (> 100 microM) of rolipram and siguazodan, a maximum response was not achieved at the highest concentration of MCh tested. As in the guinea-pig ileum, only rolipram (10-300 microM) and siguazodan (10-300 microM) produced a significant, concentration-dependent, rightward displacement of the MCh concentration-response curve (increase in EC50: rank order: rolipram > siguazodan). 4. In the guinea-pig ileum, isoprenaline (0.1 microM) produced a rightward displacement (approximately 3 fold) of the MCh concentration-response curve, accompanied by a significant depression of the maximum response. Increasing the isoprenaline concentration (1 microM) had no further effect on either parameter. Sodium nitroprusside (SNP, > or = 10 microM) produced a concentration-dependent depression of the MCh maximum without an effect on the EC50. 5. In the rat ileum, isoprenaline (1 microM) produced a concentration-dependent rightward displacement (approximately 2.8 fold) of the MCh concentration-response curve with depression of the MCh maximum at higher (> or = 100 microM) concentrations. SNP produced depression of the MCh maximum at a concentration of 10 microM and above. Effects on the MCh EC50 were seen only at 100 and 300 microM. 6. In guinea-pig ileum, isoprenaline (0.1 microM) in combination with rolipram (10 microM) further increased the MCh EC50 and reduced the MCh maximum. The combination of SNP (10 microM) with zaprinast (0.1 microM) produced no further significant effect than SNP alone. 7. In rat ileum, isoprenaline (1 microM) in combination with rolipram (10 microM) further increased the EC50 and reduced the maximum. SNP (10 microM) had no significant effect on either the MCh maximum or EC50. A combination with zaprinast (1 microM) had no further effect. 8. In conclusion, all the PDE inhibitors tested produced a concentration-dependent inhibition of the MCh concentration-response curve, indicating a modulator role for the PDE isoenzymes in gastrointestinal smooth muscle contractility. The PDE inhibitors that elevate cyclic GMP produced a depression of the MCh maximum response only, whilst those that elevate cyclic AMP produced a rightward displacement of the MCh concentration-response curve. This was confirmed by the use of isoprenaline and SNP. This difference in the type of inhibition produced by these PDE isoenzyme inhibitors may reflect a different intracellular site/mechanism by which the cyclic AMP- and cyclic GMP-activated kinases act functionally to antagonize the contractile response. PMID:8864552

Study of the effect of electromagnetic fields on indoor and outdoor radon concentrations

NASA Astrophysics Data System (ADS)

Haider, Lina M.; Shareef, N. R.; Darwoysh, H. H.; Mansour, H. L.

2018-05-01

In the present work, the effect of electromagnetic fields produced by high voltage power lines(132kV) and indoor equipments on the indoor and outdoor average radon concentrations in Al-Kazaliya and Hay Al-Adil regions in Baghdad city were studied using CR-39 track detectors and a gauss-meter.Results of measurements of the present study, have shown that the highest value for the indoor average radon concentration (76.56± 8.44 Bq / m3) was recorded for sample A1(Hay Al-Adel) at a distance of (20 m) from the high voltage power lines, while the lowest value for the indoor average radon concentration (30.46 ± 8.44 Bq / m3) was recorded for sample A3 (Hay Al-Adil) at a distance of (50 m) from the high voltage power lines. The indoor gaussmeter measurements were found to be ranged from (30.2 mG) to (38.5 mG). The higest value for outdoor average radon concentration and the highest gaussmeter measurements were found for sample (1), with values (92.63 ±11.2 Bq / m3) and (87.24 ± 2.85 mG), directly under the high voltage power lines respectively, while the lowest outdoor average radon concentration and the lowest gaussmeter measurements were found in sample (4),with values (34.19 ± 6.33 Bq / m3) and (1.16 ± 0.14 Bq / m3),), at a distance of (120 m) from the high voltage power lines respectively. The results of the present work have shown that there might be an influence of the electromagnetic field on radon concentrations in areas which were close to high voltage power lines and houses which have used many electric equipment for a long period of time.

High-power and highly efficient diode-cladding-pumped Ho3+-doped silica fiber lasers.

PubMed

Jackson, Stuart D; Bugge, Frank; Erbert, Götz

2007-11-15

We demonstrate high-power operation from a singly Ho3+-doped silica fiber laser that is cladding pumped directly with diode lasers operating at 1150 nm. Internal slope efficiencies approaching the Stokes limit were produced, and the maximum output power was 2.2W. This result was achieved using a low Ho3+-ion concentration and La3+-ion codoping, which together limit the transfer of energy between excited Ho3+ ions.

Mercury speciation and microbial transformations in mine wastes, stream sediments, and surface waters at the Almaden Mining District, Spain

USGS Publications Warehouse

Gray, John E.; Hines, Mark E.; Higueras, Pablo L.; Adatto, Isaac; Lasorsa, Brenda K.

2004-01-01

Speciation of Hg and conversion to methyl-Hg were evaluated in mine wastes, sediments, and water collected from the Almade??n District, Spain, the world's largest Hg producing region. Our data for methyl-Hg, a neurotoxin hazardous to humans, are the first reported for sediment and water from the Almade??n area. Concentrations of Hg and methyl-Hg in mine waste, sediment, and water from Almade??n are among the highest found at Hg mines worldwide. Mine wastes from Almade??n contain highly elevated Hg concentrations, ranging from 160 to 34 000 ??g/g, and methyl-Hg varies from <0.20 to 3100 ng/g. Isotopic tracer methods indicate that mine wastes at one site (Almadenejos) exhibit unusually high rates of Hg-methylation, which correspond with mine wastes containing the highest methyl-Hg concentrations. Streamwater collected near the Almade??n mine is also contaminated, containing Hg as high as 13 000 ng/L and methyl-Hg as high as 30 ng/L; corresponding stream sediments contain Hg concentrations as high as 2300 ??g/g and methyl-Hg concentrations as high as 82 ng/g. Several streamwaters contain Hg concentrations in excess of the 1000 ng/L World Health Organization (WHO) drinking water standard. Methyl-Hg formation and degradation was rapid in mines wastes and stream sediments demonstrating the dynamic nature of Hg cycling. These data indicate substantial downstream transport of Hg from the Almade??n mine and significant conversion to methyl-Hg in the surface environment.

HIGH FOLIAR NITROGEN IN DESERT SHRUBS: AN IMPORTANT ECOSYSTEM TRAIT OR DEFECTIVE DESERT DOCTRINE?

EPA Science Inventory

Nitrogen concentrations in green and senesced leaves of perennial desert shrubs were compiled from a worldwide literature search to test the validity of the doctrine that desert shrubs produce foliage and leaf litter much richer in nitrogen than that in the foliage of plants from...

Centrifugation as a pre-treatment in olive mill wastewater processing (abstract)

USDA-ARS?s Scientific Manuscript database

Olive mill wastewater (OMWW), generated during production of olive oil, is an untapped source of nutritious compounds. Thus, processors want to separate OMWW into a high-value, concentrated product stream and near-pure water. However, the amount and characteristics of the produced OMWW depend on t...

46 CFR Appendix C to Subpart C to... - Medical Surveillance Guidelines for Benzene

Code of Federal Regulations, 2010 CFR

2010-10-01

... produce primary irritation due to repeated or prolonged contact with the skin. High concentrations are... Direct skin contact with benzene may cause erythema. Repeated or prolonged contact may result in drying, scaling dermatitis or development of secondary skin infections. In addition, benzene is absorbed through...