Characterization of detonation soot produced during steady and overdriven conditions for three high explosive formulations

NASA Astrophysics Data System (ADS)

Podlesak, David W.; Huber, Rachel C.; Amato, Ronald S.; Dattelbaum, Dana M.; Firestone, Millicent A.; Gustavsen, Richard L.; Johnson, Carl E.; Mang, Joseph T.; Ringstrand, Bryan S.

2017-01-01

The detonation of high explosives (HE) produces a dense fluid of molecular gases and solid carbon. The solid detonation carbon contains various carbon allotropes such as detonation nanodiamonds, onion-like carbon, graphite and amorphous carbon, with the formation of the different forms dependent upon pressure, temperature and the environmental conditions of the detonation. We have collected solid carbon residues from controlled detonations of three HE formulations (Composition B-3, PBX 9501, and PBX 9502). Soot was collected from experiments designed to produce both steady and overdriven conditions, and from detonations in both an ambient (air) atmosphere and in an inert Ar atmosphere. Differences in solid carbon residues were quantified using X-ray photoelectron spectroscopy and carbon isotope measurements. Environmental conditions, HE formulation, and peak pressures influenced the amount of and isotopic composition of the carbon in the soot. Detonations in an Ar atmosphere produced greater amounts of carbon soot with lower δ13C values than those in ambient air. Therefore, solid carbon residues continued to evolve after detonation due to excess oxygen in the ambient air detonations. As well, higher peak pressures in overdriven conditions produced less carbon soot with, in general, higher δ13C values. Consequently, while overdriven conditions only produced peak pressures for a limited duration, it was enough to influence the composition of the solid carbon residues.

Tooling Converts Stock Bearings To Custom Bearings

NASA Technical Reports Server (NTRS)

Fleenor, E. N., Jr.

1983-01-01

Technique for reworking stock bearings saves time and produces helicopter-rotor bearings ground more precisely. Split tapered ring at one end of threaded bolt expands to hold inside of inner race bearing assembly; nut, at other end of bolt, adjusts amount of spring tension. Piece of hardware grasps bearing firmly without interfering with grinding operation. Operation produces bearing of higher quality than commercially available bearings.

Cloning, production, and functional expression of the bacteriocin enterocin A, produced by Enterococcus faecium T136, by the yeasts Pichia pastoris, Kluyveromyces lactis, Hansenula polymorpha, and Arxula adeninivorans.

PubMed

Borrero, Juan; Kunze, Gotthard; Jiménez, Juan J; Böer, Erik; Gútiez, Loreto; Herranz, Carmen; Cintas, Luis M; Hernández, Pablo E

2012-08-01

The bacteriocin enterocin A (EntA) produced by Enterococcus faecium T136 has been successfully cloned and produced by the yeasts Pichia pastoris X-33EA, Kluyveromyces lactis GG799EA, Hansenula polymorpha KL8-1EA, and Arxula adeninivorans G1212EA. Moreover, P. pastoris X-33EA and K. lactis GG799EA produced EntA in larger amounts and with higher antimicrobial and specific antimicrobial activities than the EntA produced by E. faecium T136.

Apically extruded debris with three contemporary Ni-Ti instrumentation systems: an ex vivo comparative study.

PubMed

Logani, Ajay; Shah, Naseem

2008-01-01

To comparatively evaluate the amount of apically extruded debris when ProTaper hand, ProTaper rotary and ProFile systems were used for the instrumentation of root canals. Thirty minimally curved, mature, human mandibular premolars with single canals were randomly divided into three groups of ten teeth each. Each group was instrumented using one of the three instrumentation systems: ProTaper hand, ProTaper rotary and ProFile. Five milliliters of sterile water were used as an irrigant. Debris extruded was collected in preweighed polyethylene vials and the extruded irrigant was evaporated. The weight of the dry extruded debris was established by comparing the pre- and postinstrumentation weight of polyethylene vials for each group. The Kruskal-Wallis nonparametric test and Mann-Whitney U test were applied to determine if significant differences existed among the groups ( P< 0.05). All instruments tested produced a measurable amount of debris. No statistically significant difference was observed between ProTaper hand and ProFile system ( P > 0.05). Although ProTaper rotary extruded a relatively higher amount of debris, no statistically significant difference was observed between this type and the ProTaper hand instruments ( P > 0.05). The ProTaper rotary extruded significantly more amount of debris compared to the ProFile system ( P< 0.05). Within the limitations of this study, it can be concluded that all instruments tested produced apical extrusion of debris. The ProTaper rotary extruded a significantly higher amount of debris than the ProFile.

Hydrogen enrichment of synthetic fuel

NASA Technical Reports Server (NTRS)

Jay, C. G.

1978-01-01

Synthetic gas may be produced at lower cost and higher efficiency by using outside source of hydrogen. Method is compatible with same temperatures and pressures as shift reaction. Process increases efficiency by using less coal and water to provide equal amount of synthetic gas.

Conversational Memory Employing Cued and Free Recall.

ERIC Educational Resources Information Center

Benoit, Pamela J.; Benoit, William L.

1988-01-01

Tests two hypotheses: (1) that cued recall elicits significantly more conversational information than free recall; and (2) that conversational interactants recall more of their partner's utterances than their own. Finds cued recall produced significantly higher amounts of remembering than free recall. (MS)

Evaluation of efficiency of insulin suppository formulations containing sodium salicylate or sodium cholate in insulin dependent diabetic patients.

PubMed

Hosny, Ehab A; Al-Marzouki, Zohair M H; Metwally, Mohammed E S; Souaida, Mamdouh Y S; Alshaik, Abdel Rhman A M

2003-10-01

Two formulations of insulin suppositories were prepared to contain different amounts of sodium salicylate and sodium cholate as absorption promoters and also of insulin with the purpose of obtaining the most effective formulation in reducing plasma glucose levels after rectal administration to diabetic patients. The results show that insulin suppositories containing 100 mg sodium salicylate and 100 or 200 U of crystalline insulin showed no significant difference in AUC, Cmax and Tmax and both formulations showed significant reduction in plasma glucose level compared to initial values within 1.5-2 h. The results from experiments carried out in health volunteers showed that 100 mg sodium salicylate is the optimum amount to be included in insulin suppositories producing significantly higher Cmax and AUC compared to those produced after rectal administration of insulin suppositories containing 50 or 200 mg sodium salicylate. The results also show that using sodium cholate in 50 mg amount did not produce any significant reduction in plasma glucose levels of insulin dependent diabetic patients given suppositories containing 100 U of insulin, but this amount in suppositories containing 200 U of insulin was able to produce significant (p < 0.05) reduction in plasma glucose level within 1 h which lasted till end of experiment producing Cmax of 29.7 +/- 6.61% at Tmax of 1.5 +/- 0.61 h. On increasing the amount of sodium cholate to 100 mg in the suppositories, a marked (p < 0.01) reduction in plasma glucose level took place and the Cmax increased to 47.7 +/- 12.24% at Tmax of 1.5 +/- 0.63 h. This resulted in AUC of 86.7 +/- 22.4 mg%h which was non significantly higher from that produced after administration of suppositories containing 50 mg sodium cholate and 200 U insulin (62.5 +/- 17.6 mg%h). The results also show that insulin suppositories containing 100 mg sodium cholate and 200 U insulin resulted in a non significant differences in Cmax and AUC from those produced by S.C. injection of insulin (20 U) but significantly (p < 0.001) shorter Tmax. This formulation also shows non significant differences in Tmax and AUC and significantly (p < 0.05) higher Cmax than from those produced after rectal administration of suppositories containing 100 mg of sodium salicylate and same amount of insulin. Further more this formulation produced severe hypoglycemia in control healthy volunteers within 1 h of administration producing Cmax of 57.0 +/- 18.8% at Tmax of 0.75 +/- 0.35 h. The results of this study showed that the formulation containing 100 mg of sodium cholate and 200 U of insulin tested in fasted insulin dependent diabetic patients produced a maximum % reduction in plasma glucose levels (Cmax) of 47.7 +/- 12.24% at tmax of 1.5 +/- 0.63 h compared to Cmax of 50.56 +/- 6.8% at tmax of 2.93 +/- 0.19 h resulted after subcutaneous injection of 20 U insulin. These suppositories produced an area under the curve (AUC) of 87 +/- 22.4 mg%h compared to an AUC of 81 +/- 13.4 mg%h obtained after subcutaneous injection. This formulation of suppositories studied in 7 insulin dependent diabetic patients was found to abolish the 2-h post-prandial significant rise in plasma glucose levels after meal. These results show that these insulin suppositories containing 100 mg of sodium cholate and 200 U of insulin can serve as effective buffer against meal related hyperglycemia. The suppositories were safe, effective, accepted and well tolerated by the tested individuals.

Influence of extraction techniques on physical-chemical characteristics and volatile compounds of extra virgin olive oil.

PubMed

Volpe, Maria Grazia; De Cunzo, Fausta; Siano, Francesco; Paolucci, Marina; Barbarisi, Costantina; Cammarota, Giancarlo

2014-01-01

The purpose of this study was to investigate three types of extraction methods of extra virgin olive oil (EVOO) from the same cultivar (Ortice olive cultivar): traditional or pressing (T) system, decanter centrifugation (DC) system and a patented horizontal axis decanter centrifugation (HADC) system. Oil samples were subjected to chemical analyses: free acidity, peroxide value, ultraviolet light absorption K232 and K270, total polyphenols, antioxidant capacity, volatile compounds and olfactory characteristics by electronic nose. The two centrifugation systems showed better free acidity and peroxides value but total polyphenol content was particularly high in extra virgin olive oil produced by patented HADC system. Same volatile substances that positively characterize the oil aroma were found in higher amount in the two centrifugation systems, although some differences have been detected between DC and HADC system, other were found in higher amount in extra virgin olive oil produced by T system. The electronic nose analysis confirmed these results, principal component analysis (PCA) and correlation matrix showed the major differences between EVOO produced by T and HADC system. Taken together the results showed that DC and HADC systems produce EVOO with better characteristics than T system and patented HADC is the best extraction system.

Precursor effects on the morphology and crystallinity of manganese oxides and their catalytic application for methylene blue degradation

NASA Astrophysics Data System (ADS)

Awaluddin, Amir; Agustina, Mutia; Aulia, Rizki Rilda; Muhdarina

2017-03-01

The cryptomelane-type manganese oxide catalysts have been prepared by sol-gel method based on the redox reaction between potassium permanganate and glucose or oxalic acid. These catalysts belong to a class of porous manganese oxides known as octahedral molecular sieves (OMS). The SEM results indicated that the marked difference between the morphology of the cyptomelanes produced from glucose and oxalic acid. The glucose precursor produces cotton-shaped morphology, whereas the oxalic acid precursor leads to the formation of the disk-like appearances. The XRD results indicated that the glucose precursor produces more crystalline cryptomelane than that of oxalic acid. The effect of catalyst dosage on methyelene blue degradation was evaluated. Dye-decomposing activity was proportional to the amount of catalyst used, increasing of the catalyst amount leads to higher degradation of methyelene blue at short period of reaction. With different crystalline structures and morphology appearances of the cyptomelanes, however, the total degradation of methylene blue is relatively the same at 120 minute of reaction time with catalyst amount of 100 mg.

Effect of copper chloride on the emissions of PCDD/Fs and PAHs from PVC combustion.

PubMed

Wang, Dongli; Xu, Xiaobai; Zheng, Minghui; Chiu, Chung H

2002-09-01

The influences of temperature, air flow and the amount of copper chloride upon the types and amount of the toxic emissions such as polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) and polycyclic aromatic hydrocarbons (PAHs) during combustion of polyvinyl chloride (PVC) were investigated. The mechanism concerning the effect of temperature and copper chloride on the PCDD/Fs and PAHs formation was discussed. The results shown that without copper chloride, trace amounts of PCDD/Fs and large amounts of PAHs were found in the emissions from the pure PVC combustion under various combustion conditions. The addition of copper chloride enhanced PCDD/Fs formation, but it seems that the formation of PAHs decreased with increasing amount of copper chloride, and greater total amount of PAHs were produced at the higher temperature under our experimental conditions.

Sub-lethal levels of electric current elicit the biosynthesis of plant secondary metabolites.

PubMed

Kaimoyo, Evans; Farag, Mohamed A; Sumner, Lloyd W; Wasmann, Catherine; Cuello, Joel L; VanEtten, Hans

2008-01-01

Many secondary metabolites that are normally undetectable or in low amounts in healthy plant tissue are synthesized in high amounts in response to microbial infection. Various abiotic and biotic agents have been shown to mimic microorganisms and act as elicitors of the synthesis of these plant compounds. In the present study, sub-lethal levels of electric current are shown to elicit the biosynthesis of secondary metabolites in transgenic and non-transgenic plant tissue. The production of the phytoalexin (+)-pisatin by pea was used as the main model system. Non-transgenic pea hairy roots treated with 30-100 mA of electric current produced 13 times higher amounts of (+)-pisatin than did the non-elicited controls. Electrically elicited transgenic pea hairy root cultures blocked at various enzymatic steps in the (+)-pisatin biosynthetic pathway also accumulated intermediates preceding the blocked enzymatic step. Secondary metabolites not usually produced by pea accumulated in some of the transgenic root cultures after electric elicitation due to the diversion of the intermediates into new pathways. The amount of pisatin in the medium bathing the roots of electro-elicited roots of hydroponically cultivated pea plants was 10 times higher 24 h after elicitation than in the medium surrounding the roots of non-elicited control plants, showing not only that the electric current elicited (+)-pisatin biosynthesis but also that the (+)-pisatin was released from the roots. Seedlings, intact roots or cell suspension cultures of fenugreek (Trigonella foenum-graecum), barrel medic, (Medicago truncatula), Arabidopsis thaliana, red clover (Trifolium pratense) and chickpea (Cicer arietinum) also produced increased levels of secondary metabolites in response to electro-elicitation. On the basis of our results, electric current would appear to be a general elicitor of plant secondary metabolites and to have potential for application in both basic and commercial research.

Study on the optimal moisture adding rate of brown rice during germination by using segmented moisture conditioning method.

PubMed

Cao, Yinping; Jia, Fuguo; Han, Yanlong; Liu, Yang; Zhang, Qiang

2015-10-01

The aim of this study was to find out the optimal moisture adding rate of brown rice during the process of germination. The process of water addition in brown rice could be divided into three stages according to different water absorption speeds in soaking process. Water was added with three different speeds in three stages to get the optimal water adding rate in the whole process of germination. Thus, the technology of segmented moisture conditioning which is a method of adding water gradually was put forward. Germinated brown rice was produced by using segmented moisture conditioning method to reduce the loss of water-soluble nutrients and was beneficial to the accumulation of gamma aminobutyric acid. The effects of once moisture adding amount in three stages on the gamma aminobutyric acid content in germinated brown rice and germination rate of brown rice were investigated by using response surface methodology. The optimum process parameters were obtained as follows: once moisture adding amount of stage I with 1.06 %/h, once moisture adding amount of stage II with 1.42 %/h and once moisture adding amount of stage III with 1.31 %/h. The germination rate under the optimum parameters was 91.33 %, which was 7.45 % higher than that of germinated brown rice produced by soaking method (84.97 %). The content of gamma aminobutyric acid in germinated brown rice under the optimum parameters was 29.03 mg/100 g, which was more than two times higher than that of germinated brown rice produced by soaking method (12.81 mg/100 g). The technology of segmented moisture conditioning has potential applications for studying many other cereals.

Fractionation and identification of novel antioxidant peptides from buffalo and bovine casein hydrolysates.

PubMed

Shazly, Ahmed Behdal; He, Zhiyong; El-Aziz, Mahmoud Abd; Zeng, Maomao; Zhang, Shuang; Qin, Fang; Chen, Jie

2017-10-01

Buffalo and bovine caseins were hydrolysed by alcalase and trypsin to produce novel antioxidant peptides. The casein hydrolysates were purified using ultrafiltration (UF) and further characterized by RP-HPLC. The fractions produced higher antioxidant activities were identified for their peptides using LC MS/MS. All UF-VI (MW<1kDa) fractions showed higher antioxidant activity. Hydrolysate produced by alcalase for buffalo casein (UF-VI with 54.84-fold purification) showed higher antioxidant activity than that obtained by trypsin. Trypsin hydrolysate contained high amount of hydrophobic amino acids while alcalase hydrolysate consisted mainly of Ser, Arg, Ala and Leu. The antioxidant peptides identified by LC MS/MS were RELEE, MEDNKQ and TVA, EQL in buffalo casein hydrolysates produced by trypsin and alcalase, respectively. Mechanism and reaction pathways of selected antioxidant peptides with ABTS were proposed. Conclusively, buffalo casein provided antioxidant peptides similar to bovine, suggesting that buffalo casein is a novel source of antioxidant. Copyright © 2017 Elsevier Ltd. All rights reserved.

Production of Mushroom Mycelium as a Protein and Fat Source in Submerged Culture in Medium of Vinasse

PubMed Central

Falanghe, H.

1962-01-01

Of ten mushroom cultures investigated, only Agaricus campestris, Boletus indecisus, and Tricholoma nudum were capable of growing in submerged culture in medium of vinasse with added salts. Higher fermentative efficiencies were found under these conditions than in medium containing molasses or waste sulfite liquor. A. campestris showed a better capacity to produce protein but, since B. indecisus is capable of developing greater mycelium weight, its fermentative efficiencies are comparable. Both microorganisms could be grown in medium of vinasse with greatly varied amounts, producing higher mycelial weight in media with greater vinasse. The capacity of B. indecisus and A. campestris to utilize the noncarbohydrate fraction in total solids, instead of the total carbohydrates when they are in smaller amount, was observed in medium containing vinasse. B. indecisus and A. campestris were easily separated by filtration from the medium, although T. nudum was difficult to separate by this procedure. In experiments with A. campestris, the adaptative capacity of the organism to vinasse was demonstrated. PMID:13962715

Controlling composition and color characteristics of Monascus pigments by pH and nitrogen sources in submerged fermentation.

PubMed

Shi, Kan; Song, Da; Chen, Gong; Pistolozzi, Marco; Wu, Zhenqiang; Quan, Lei

2015-08-01

Submerged fermentations of Monascus anka were performed with different nitrogen sources at different pH in 3 L bioreactors. The results revealed that the Monascus pigments dominated by different color components (yellow pigments, orange pigments or red pigments) could be selectively produced through pH control and nitrogen source selection. A large amount of intracellular pigments dominated by orange pigments and a small amount of water-soluble extracellular yellow pigments were produced at low pH (pH 2.5 and 4.0), independently of the nitrogen source employed. At higher pH (pH 6.5), the role of the nitrogen source became more significant. In particular, when ammonium sulfate was used as nitrogen source, the intracellular pigments were dominated by red pigments with a small amount of yellow pigments. Conversely, when peptone was used, intracellular pigments were dominated by yellow pigments with a few red pigments derivatives. Neither the presence of peptone nor ammonium sulfate promoted the production of intracellular orange pigments while extracellular pigments with an orangish red color were observed in both cases, with a higher yield when peptone was used. Two-stage pH control fermentation was then performed to improve desirable pigments yield and further investigate the effect of pH and nitrogen sources on pigments composition. These results provide a useful strategy to produce Monascus pigments with different composition and different color characteristics. Copyright © 2015 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Value of acid metabolic products in identification of certain corynebacteria.

PubMed Central

Reddy, C A; Kao, M

1978-01-01

Acid metabolic products of 23 strains of human and animal pathogenic corynebacteria, representing eight different species, were determined by gas chromatography. The results showed that the species examined were metabolically heterogeneous and could be presumptively identified based on the acid products produced. Corynebacterium equi did not produce any acids; C. renale produced lactate; and C. pyogenes produced major amounts of lactate, variable amounts of acetate, and minor amounts of succinate and pyruvate. C. kutscheri produced propionate and lactate as major products and pyruvate and oxalacetate as minor products. C. diphtheriae and C. pseudotuberculosis produced major amounts of propionate, acetate, and formate. In addition, C. pseudotuberculosis produced major amounts of pyruvate and minor amounts of succinate, lactate, and oxalacetate, whereas C. diphtheriae strains produced minor but variable amounts of lactate, succinate, fumarate, pyruvate, and oxalacetate. C. bovis produced aicd products similar to those of C. pyogenes but was readily distinguishable from the latter by the lack of hemolysis on blood agar, colony morphology, catalase reaction, and biochemicals. C. suis characteristically produced major amounts of ethanol, acetate, and formate and minor amounts of lactate and succinate but no propionate. PMID:96126

L-Asparaginase Production by the Rumen Anaerobe Vibrio succinogenes

PubMed Central

Kafkewitz, David; Goodman, David

1974-01-01

The rumen anaerobe Vibrio succinogenes possesses a constitutive L-asparaginase. The amount of enzyme produced is affected by the compound supplied to the organism to generate the fumaric acid it requires as a terminal electron acceptor. When nitrate is provided as the terminal electron acceptor, the amount of enzyme produced is affected by the compound provided to satisfy the nutritional requirement of the organism for succinic acid. Specific activities of up to 8.4 IU/mg of protein in cell-free extracts have been obtained. This specific activity is higher than has been previously reported for any organism. The enzyme has an apparent Km of 1.7 × 10-5 M and low activity towards L-glutamine when assayed at pH 8.5. PMID:4855647

Energy-reduction concept for incandescent lamps

NASA Technical Reports Server (NTRS)

Vorhaben, K. H.

1981-01-01

Reusable infrared reflector maintains filament temperature and reduces power requirements. Fixed installed over light bulb directs energy formerly lost back to lamp filament. This energy aids electric current in heating filament, allowing lower-wattage bulb to produce same amount of light as higher-wattage bulb in ordinary fixture.

Methane Pyrolysis and Disposing Off Resulting Carbon

NASA Technical Reports Server (NTRS)

Sharma, P. K.; Rapp, D.; Rahotgi, N. K.

1999-01-01

Sabatier/Electrolysis (S/E) is a leading process for producing methane and oxygen for application to Mars ISPP. One significant problem with this process is that it produces an excess of methane for combustion with the amount of oxygen that is produced. Therefore, one must discard roughly half of the methane to obtain the proper stoichiometric methane/oxygen mixture for ascent from Mars. This is wasteful of hydrogen, which must be brought from Earth and is difficult to transport to Mars and store on Mars. To reduced the problem of transporting hydrogen to Mars, the S/E process can be augmented by another process which reduces overall hydrogen requirement. Three conceptual approaches for doing this are (1) recover hydrogen from the excess methane produced by the S/E process, (2) convert the methane to a higher hydrocarbon or other organic with a lower H/C ratio than methane, and (3) use a separate process (such as zirconia or reverse water gas shift reaction) to produce additional oxygen, thus utilizing all the methane produced by the Sabatier process. We report our results here on recovering hydrogen from the excess methane using pyrolysis of methane. Pyrolysis has the advantage that it produces almost pure hydrogen, and any unreacted methane can pass through the S/E process reactor. It has the disadvantage that disposing of the carbon produced by pyrolysis presents difficulties. Hydrogen may be obtained from methane by pyrolysis in the temperature range 10000-12000C. The main reaction products are hydrogen and carbon, though very small amounts of higher hydrocarbons, including aromatic hydrocarbons are formed. The conversion efficiency is about 95% at 12000C. One needs to distinguish between thermodynamic equilibrium conversion and conversion limited by kinetics in a finite reactor.

Delta/mu opioid receptor interactions in operant conditioning assays of pain-depressed responding and drug-induced rate suppression: assessment of therapeutic index in male Sprague Dawley rats.

PubMed

Cone, Katherine; Lanpher, Janell; Kinens, Abigail; Richard, Philomena; Couture, Sarah; Brackin, Rebecca; Payne, Emily; Harrington, Kylee; Rice, Kenner C; Stevenson, Glenn W

2018-05-01

Although delta/mu receptor interactions vary as a function of behavioral endpoint, there have been no assessments of these interactions using assays of pain-depressed responding. This is the first report of delta/mu interactions using an assay of pain-depressed behavior. A mult-cycle FR10 operant schedule was utilized in the presence of (nociception) and in the absence of (rate suppression) a lactic acid inflammatory pain-like manipulation. SNC80 and methadone were used as selective/high efficacy delta and mu agonists, respectively. Both SNC80 and methadone alone produced a dose-dependent restoration of pain-depressed responding and dose-dependent response rate suppression. Three fixed ratio mixtures, based on the relative potencies of the drugs in the nociception assay, also produced dose-dependent antinociception and sedation. Isobolographic analysis indicated that all three mixtures produced supra-additive antinociceptive effects and simply additive sedation effects. The therapeutic index (TI) inversely varied as a function of amount of SNC80 in the mixture, such that lower amounts of SNC80 produced a higher TI, and larger amounts produced a lower TI. Compared to literature using standard pain-elicited assays, the orderly relationship between SNC80 and TI reported here may be a unique function of assessing pain-depressed behavior.

Quality Characteristics and Quantification of Acetaldehyde and Methanol in Apple Wine Fermentation by Various Pre-Treatments of Mash

PubMed Central

Won, Seon Yi; Seo, Jae Soon; Kwak, Han Sub; Lee, Youngseung; Kim, Misook; Shim, Hyoung-Seok; Jeong, Yoonhwa

2015-01-01

The objective of this study was to compare the effects of adding lactic acid and pectinase, and chaptalization for the quality of apple wine and the production of hazardous compounds (methanol and acetaldehyde). The pH of all of the samples was below 4; therefore, mash seemed to be fermented without any issue. Total acidity was the highest in sample A due to lactic acid addition. Pre-treated groups (samples B, C, and D) showed higher total acidities than that of the control (P<0.05). Pre-treatments might influence the production of organic acids in apple wines. The control and pectinase added sample (sample B) had the lowest alcohol contents. Adding lactic acid produced more alcohol, and chaptalized samples produced more alcohol due to the addition of sugar. Adding pectinase with and without chaptalization was not effective for producing more alcohol. The control sample had significantly higher acetaldehyde content (2.39 mg/L) than the other samples (1.00~2.07 mg/L); therefore, pre-treatments for apple wine fermentation produced a lower amount of acetaldehyde. Among the pre-treated samples, samples C and D showed the lowest acetaldehyde content of 1.00 mg/L and 1.16 mg/L, respectively. On the other hand, a significantly higher amount of methanol was generated for sample A (1.03 mg/L) and sample D (1.22 mg/L) than that of the control (0.82 mg/L) (P<0.05). Adding lactic acid or chaptalization was effective in reducing methanol and acetaldehyde in apple wines. PMID:26770917

Higher Education Administrators Roles in Fortification of Information Security Program

ERIC Educational Resources Information Center

Eyadat, Mohammad S.

2015-01-01

Information systems produce significant benefits to organizations. Therefore, organizations invest tremendous amount of money and time to obtain and manage information in order to maintain a high level of performance and to remain competitive. There are many factors that can impact the organizational information management and performance. One of…

Evaluation of maillard reaction variables and their effect on heterocyclic amine formation in chemical model systems.

PubMed

Dennis, Cara; Karim, Faris; Smith, J Scott

2015-02-01

Heterocyclic amines (HCAs), highly mutagenic and potentially carcinogenic by-products, form during Maillard browning reactions, specifically in muscle-rich foods. Chemical model systems allow examination of in vitro formation of HCAs while eliminating complex matrices of meat. Limited research has evaluated the effects of Maillard reaction parameters on HCA formation. Therefore, 4 essential Maillard variables (precursors molar concentrations, water amount, sugar type, and sugar amounts) were evaluated to optimize a model system for the study of 4 HCAs: 2-amino-3-methylimidazo-[4,5-f]quinoline, 2-amino-3-methylimidazo[4,5-f]quinoxaline, 2-amino-3,8-dimethylimidazo[4,5-f]quinoxaline, and 2-amino-3,4,8-trimethyl-imidazo[4,5-f]quinoxaline. Model systems were dissolved in diethylene glycol, heated at 175 °C for 40 min, and separated using reversed-phase liquid chromatography. To define the model system, precursor amounts (threonine and creatinine) were adjusted in molar increments (0.2/0.2, 0.4/0.4, 0.6/0.6, and 0.8/0.8 mmol) and water amounts by percentage (0%, 5%, 10%, and 15%). Sugars (lactose, glucose, galactose, and fructose) were evaluated in several molar amounts proportional to threonine and creatinine (quarter, half, equi, and double). The precursor levels and amounts of sugar were significantly different (P < 0.05) in regards to total HCA formation, with 0.6/0.6/1.2 mmol producing higher levels. Water concentration and sugar type also had a significant effect (P < 0.05), with 5% water and lactose producing higher total HCA amounts. A model system containing threonine (0.6 mmol), creatinine (0.6 mmol), and glucose (1.2 mmol), with 15% water was determined to be the optimal model system with glucose and 15% water being a better representation of meat systems. © 2015 Institute of Food Technologists®

Cluster Bean—A Ureide- or Amide-Producing Legume? 1

PubMed Central

Sheoran, Inder S.; Luthra, Yash P.; Kuhad, Mohinder S.; Singh, Randhir

1982-01-01

Xylem sap of cluster bean (Cyamopsis tetragonoloba L. cv FS-277) and pigeonpea (Cajanus cajan cv UPAS-120) were analyzed for total nitrogen, amide nitrogen, and ureide nitrogen at flowering stage. Nitrogenase, uricase, and allantoinase were compared in nodules of cluster bean and pigeonpea. Xylem sap of cluster bean exhibited higher amounts of amides as compared to ureides, and the activities of uricase and allantoinase (ureide-producing enzymes) in nodules were also low, whereas the reverse was the case for pigeonpea. Based on these investigations, it has been concluded that cluster bean is an amide-producing legume rather than ureide-producing as had been reported earlier. PMID:16662600

Nitrous oxide flux from landfill leachate-sawdust nitrogenous compost.

PubMed

Hui, C H; So, M K; Lee, C M; Chan, G Y S

2003-09-01

Composted nitrogenous waste has the potential to produce excessive amounts of nitrous oxide (N2O), a potent greenhouse gas that also contributes to stratospheric ozone depletion. In this laboratory study, sawdust was irrigated with varying amounts of landfill leachate with high NH4+-N content (3950 mg l(-1)). Physicochemical properties, including the amount of N2O produced, were monitored during the composting process over 28 days. A rapid decline in NH4+-N in the first 4 days and increasing NO3--N for 11 days was followed by lower but stabilized levels of available-N, even with repeated leachate irrigation. Less than 0.03% of the leachate-applied N was lost as N2O. Higher leachate applications as much as tripled N2O production, but this represented a lesser proportion overall of the total nitrogen. Addition of glucose to the composting process had no significant effect on N2O production. The derived sawdust-leachate compost supported healthy growth of Sesbania rostrata. It is concluded that compost can be produced from sawdust irrigated with landfill leachate without substantial emission of N2O, although excessive flux of N2O remains about high application rates over longer time periods.

A XANES Study of Sulfur Speciation and Reactivity in Cokes for Anodes Used in Aluminum Production

NASA Astrophysics Data System (ADS)

Jahrsengene, Gøril; Wells, Hannah C.; Rørvik, Stein; Ratvik, Arne Petter; Haverkamp, Richard G.; Svensson, Ann Mari

2018-03-01

Availability of anode raw materials in the growing aluminum industry results in a wider range of petroleum cokes being used to produce carbon anodes. The boundary between anode grade cokes and what previously was considered non-anode grades are no longer as distinct as before, leading to introduction of cokes with higher sulfur and higher trace metal impurity content in anode manufacturing. In this work, the chemical nature of sulfur in five industrial cokes, ranging from 1.42 to 5.54 wt pct S, was investigated with K-edge XANES, while the reactivity of the cokes towards CO2 was measured by a standard mass loss test. XANES identified most of the sulfur as organic sulfur compounds. In addition, a significant amount is identified (16 to 53 pct) as S-S bound sulfur. A strong inverse correlation is observed between CO2-reactivity and S-S bound sulfur in the cokes, indicating that the reduction in reactivity is more dependent on the amount of this type of sulfur compound rather than the total amount of sulfur or the amount of organic sulfur.

A XANES Study of Sulfur Speciation and Reactivity in Cokes for Anodes Used in Aluminum Production

NASA Astrophysics Data System (ADS)

Jahrsengene, Gøril; Wells, Hannah C.; Rørvik, Stein; Ratvik, Arne Petter; Haverkamp, Richard G.; Svensson, Ann Mari

2018-06-01

Availability of anode raw materials in the growing aluminum industry results in a wider range of petroleum cokes being used to produce carbon anodes. The boundary between anode grade cokes and what previously was considered non-anode grades are no longer as distinct as before, leading to introduction of cokes with higher sulfur and higher trace metal impurity content in anode manufacturing. In this work, the chemical nature of sulfur in five industrial cokes, ranging from 1.42 to 5.54 wt pct S, was investigated with K-edge XANES, while the reactivity of the cokes towards CO2 was measured by a standard mass loss test. XANES identified most of the sulfur as organic sulfur compounds. In addition, a significant amount is identified (16 to 53 pct) as S-S bound sulfur. A strong inverse correlation is observed between CO2-reactivity and S-S bound sulfur in the cokes, indicating that the reduction in reactivity is more dependent on the amount of this type of sulfur compound rather than the total amount of sulfur or the amount of organic sulfur.

Radioactivities vs. depth in Apollo 16 and 17 soil

NASA Technical Reports Server (NTRS)

Fireman, E. L.; D'Amico, J.; Defelice, J.

1973-01-01

The radioactivities of Ar-37, Ar-39, and H-3 measured at a number of depths for Apollo 16 and 17 soil are reported. The Ar-37 activities vs depth in the Apollo 16 drill string increased with depth and reached a broad maximum in the neighborhood of 50 g per sq cm before decreasing. The Ar-39 activities in Apollo 17 soil were higher than in Apollo 16 soil, probably owing to the higher Fe and Ti contents. The H-3 activities in Apollo 16 and 17 soil were quite similar and indicate that the 4 August 1972 flare produced very little H-3 compared to the amount produced by solar flares during the previous 50 years.

Non-Caking Freeze Dried Applesauce

DTIC Science & Technology

A study was initiated to develop an applesauce which resists caking when subjected to elevated temperatures such as 37.7C. for two weeks and/or 57C...following results were obtained: (1) The degree of caking of the freeze dried applesauce powder was correlated with the amount of juice extracted. (2... applesauce powders. (3) Reducing sugars appear to be the factor contributing most significantly to the caking with the higher reducing sugar levels producing the higher degrees of caking.

Carbon monoxide fermentation to ethanol by Clostridium autoethanogenum in a bioreactor with no accumulation of acetic acid.

PubMed

Abubackar, Haris Nalakath; Veiga, María C; Kennes, Christian

2015-06-01

Fermentation of CO or syngas offers an attractive route to produce bioethanol. However, during the bioconversion, one of the challenges to overcome is to reduce the production of acetic acid in order to minimize recovery costs. Different experiments were done with Clostridium autoethanogenum. With the addition of 0.75 μM tungsten, ethanol production from carbon monoxide increased by about 128% compared to the control, without such addition, in batch mode. In bioreactors with continuous carbon monoxide supply, the maximum biomass concentration reached at pH 6.0 was 109% higher than the maximum achieved at pH 4.75 but, interestingly, at pH 4.75, no acetic acid was produced and the ethanol titer reached a maximum of 867 mg/L with minor amounts of 2,3-butanediol (46 mg/L). At the higher pH studied (pH 6.0) in the continuous gas-fed bioreactor, almost equal amounts of ethanol and acetic acid were formed, reaching 907.72 mg/L and 910.69 mg/L respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

The Influence of Friction Between Football Helmet and Jersey Materials on Force: A Consideration for Sport Safety.

PubMed

Rossi, Anthony M; Claiborne, Tina L; Thompson, Gregory B; Todaro, Stacey

2016-09-01

The pocketing effect of helmet padding helps to dissipate forces experienced by the head, but if the player's helmet remains stationary in an opponent's shoulder pads, the compressive force on the cervical spine may increase. To (1) measure the coefficient of static friction between different football helmet finishes and football jersey fabrics and (2) calculate the potential amount of force on a player's helmet due to the amount of friction present. Cross-sectional study. Laboratory. Helmets with different finishes and different football jersey fabrics. The coefficient of friction was determined for 2 helmet samples (glossy and matte), 3 football jerseys (collegiate, high school, and youth), and 3 types of jersey numbers (silkscreened, sublimated, and stitched on) using the TAPPI T 815 standard method. These measurements determined which helmet-to-helmet, helmet-to-jersey number, and helmet-to-jersey material combination resulted in the least amount of static friction. The glossy helmet versus glossy helmet combination produced a greater amount of static friction than the other 2 helmet combinations (P = .013). The glossy helmet versus collegiate jersey combination produced a greater amount of static friction than the other helmet-to-jersey material combinations (P < .01). The glossy helmet versus silkscreened numbers combination produced a greater amount of static friction than the other helmet-to-jersey number combinations (P < .01). The force of static friction experienced during collisions can be clinically relevant. Conditions with higher coefficients of static friction result in greater forces. In this study, the highest coefficient of friction (glossy helmet versus silkscreened number) could increase the forces on the player's helmet by 3553.88 N when compared with other helmet-to-jersey combinations. Our results indicate that the makeup of helmet and uniform materials may affect sport safety.

Enhanced isoprenoid production from xylose by engineered Saccharomyces cerevisiae.

PubMed

Kwak, Suryang; Kim, Soo Rin; Xu, Haiqing; Zhang, Guo-Chang; Lane, Stephan; Kim, Heejin; Jin, Yong-Su

2017-11-01

Saccharomyces cerevisiae has limited capabilities for producing fuels and chemicals derived from acetyl-CoA, such as isoprenoids, due to a rigid flux partition toward ethanol during glucose metabolism. Despite numerous efforts, xylose fermentation by engineered yeast harboring heterologous xylose metabolic pathways was not as efficient as glucose fermentation for producing ethanol. Therefore, we hypothesized that xylose metabolism by engineered yeast might be a better fit for producing non-ethanol metabolites. We indeed found that engineered S. cerevisiae on xylose showed higher expression levels of the enzymes involved in ethanol assimilation and cytosolic acetyl-CoA synthesis than on glucose. When genetic perturbations necessary for overproducing squalene and amorphadiene were introduced into engineered S. cerevisiae capable of fermenting xylose, we observed higher titers and yields of isoprenoids under xylose than glucose conditions. Specifically, co-overexpression of a truncated HMG1 (tHMG1) and ERG10 led to substantially higher squalene accumulation under xylose than glucose conditions. In contrast to glucose utilization producing massive amounts of ethanol regardless of aeration, xylose utilization allowed much less amounts of ethanol accumulation, indicating ethanol is simultaneously re-assimilated with xylose consumption and utilized for the biosynthesis of cytosolic acetyl-CoA. In addition, xylose utilization by engineered yeast with overexpression of tHMG1, ERG10, and ADS coding for amorphadiene synthase, and the down-regulation of ERG9 resulted in enhanced amorphadiene production as compared to glucose utilization. These results suggest that the problem of the rigid flux partition toward ethanol production in yeast during the production of isoprenoids and other acetyl-CoA derived chemicals can be bypassed by using xylose instead of glucose as a carbon source. Biotechnol. Bioeng. 2017;114: 2581-2591. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Chalk dustfall during classroom teaching: particle size distribution and morphological characteristics.

PubMed

Majumdar, Deepanjan; William, S P M Prince

2009-01-01

The study was undertaken to examine the nature of particulate chalk dust settled on classroom floor during traditional teaching with dusting and non-dusting chalks on two types of boards viz. rough and smooth. Settling chalk particles were collected for 30 min during teaching in glass Petri plates placed in classrooms within 3 m distance from the teaching boards. Particle size distribution, scanning electron microscopic images of chalk dusts and compressive strength of two types of chalks were tested and evaluated. Results showed that a larger proportion of dusts generated from anti-dusting chalks were of <4.5 and <2.5 microm size on both smooth and rough boards, as compared to dusting chalks. Non-dusting chalks, on an average, produced about 56% and 62% (by volume) of <4.5 microm (respirable) diameter, on rough and smooth boards, respectively, while the corresponding values for dusting chalks were 36% and 45%. Also, on an average, 83% and 94% (by volume) of the particles were <11 microm (thoracic) in case of non-dusting chalks against 61% and 72% for dusting chalks on rough and smooth boards, respectively. Interestingly, taking into account the mass of chalk dust produced per unit time, which was higher in dusting chalks than non dusting chalks, the former was actually producing higher amount of PM <4.5 and <11 particles from both types of boards. Scanning electron microscope images revealed that chalk particles had random shape, although in dusting chalks prevalence of elongated particles was observed, apparently due to the longitudinal breaking of the chalks during writing, which was confirmed during compressive strength testing. We could conclude that dusting chalks could be potentially more harmful than anti dusting chalks, as they produced higher amount of potentially dangerous PM 4.5 and PM 11.

Secretory production of tetrameric native full-length streptavidin with thermostability using Streptomyces lividans as a host.

PubMed

Noda, Shuhei; Matsumoto, Takuya; Tanaka, Tsutomu; Kondo, Akihiko

2015-01-13

Streptavidin is a tetrameric protein derived from Streptomyces avidinii, and has tight and specific biotin binding affinity. Applications of the streptavidin-biotin system have been widely studied. Streptavidin is generally produced using protein expression in Escherichia coli. In the present study, the secretory production of streptavidin was carried out using Streptomyces lividans as a host. In this study, we used the gene encoding native full-length streptavidin, whereas the core region is generally used for streptavidin production in E. coli. Tetrameric streptavidin composed of native full-length streptavidin monomers was successfully secreted in the culture supernatant of S. lividans transformants, and had specific biotin binding affinity as strong as streptavidin produced by E. coli. The amount of Sav using S. lividans was about 9 times higher than using E. coli. Surprisingly, streptavidin produced by S. lividans exhibited affinity to biotin after boiling, despite the fact that tetrameric streptavidin is known to lose its biotin binding ability after brief boiling. We successfully produced a large amount of tetrameric streptavidin as a secretory-form protein with unique thermotolerance.

Microbiota of Minas cheese as influenced by the nisin producer Lactococcus lactis subsp. lactis GLc05.

PubMed

Perin, Luana Martins; Dal Bello, Barbara; Belviso, Simona; Zeppa, Giuseppe; Carvalho, Antônio Fernandes de; Cocolin, Luca; Nero, Luís Augusto

2015-12-02

Minas cheese is a popular dairy product in Brazil that is traditionally produced using raw or pasteurized cow milk. This study proposed an alternative production of Minas cheese using raw goat milk added of a nisin producer Lactococcus lactis subsp. lactis GLc05. An in situ investigation was carried on to evaluate the interactions between the L. lactis subsp. lactis GLc05 and the autochthonous microbiota of a Minas cheese during the ripening; production of biogenic amines (BAs) was assessed as a safety aspect. Minas cheese was produced in two treatments (A, by adding L. lactis subsp. lactis GLc05, and B, without adding this strain), in three independent repetitions (R1, R2, and R3). Culture dependent (direct plating) and independent (rep-PCR and PCR-DGGE) methods were employed to characterize the microbiota and to assess the possible interferences caused by L. lactis subsp. lactis GLc05. BA amounts were measured using HPLC. A significant decrease in coagulase-positive cocci was observed in the cheeses produced by adding L. lactis subsp. lactis GLc05 (cheese A). The rep-PCR and PCR-DGGE highlighted the differences in the microbiota of both cheeses, separating them into two different clusters. Lactococcus sp. was found as the main microorganism in both cheeses, and the microbiota of cheese A presented a higher number of species. High concentrations of tyramine were found in both cheeses and, at specific ripening times, the BA amounts in cheese B were significantly higher than in cheese A (p<0.05). The interaction of nisin producer L. lactis subsp. lactis GLc05 was demonstrated in situ, by demonstration of its influence in the complex microbiota naturally present in a raw goat milk cheese and by controlling the growth of coagulase-positive cocci. L. lactis subsp. lactis GLc05 influenced also the production of BA determining that their amounts in the cheeses were maintained at acceptable levels for human consumption. Copyright © 2015 Elsevier B.V. All rights reserved.

Dextrose monohydrate as a non-animal sourced alternative diluent in high shear wet granulation tablet formulations.

PubMed

Mitra, Biplob; Wolfe, Chad; Wu, Sy-Juen

2018-05-01

The feasibility of dextrose monohydrate as a non-animal sourced diluent in high shear wet granulation (HSWG) tablet formulations was determined. Impacts of granulation solution amount and addition time, wet massing time, impeller speed, powder and solution binder, and dry milling speed and screen opening size on granule size, friability and density, and tablet solid fraction (SF) and tensile strength (TS) were evaluated. The stability of theophylline tablets TS, disintegration time (DT) and in vitro dissolution were also studied. Following post-granulation drying at 60 °C, dextrose monohydrate lost 9% water and converted into the anhydrate form. Higher granulation solution amounts and faster addition, faster impeller speeds, and solution binder produced larger, denser and stronger (less friable) granules. All granules were compressed into tablets with acceptable TS. Contrary to what is normally observed, denser and larger granules (at ≥21% water level) produced tablets with a higher TS. The TS of the weakest tablets increased the most after storage at both 25 °C/60% RH and 40 °C/75% RH. Tablet DT was higher for stronger granules and after storage. Tablet dissolution profiles for 21% or less water were comparable and did not change on stability. However, the dissolution profile for tablets prepared with 24% water was slower initially and continued to decrease on stability. The results indicate a granulation water amount of not more than 21% is required to achieve acceptable tablet properties. This study clearly demonstrated the utility of dextrose monohydrate as a non-animal sourced diluent in a HSWG tablet formulation.

Oxidative potential of logwood and pellet burning particles assessed by a novel profluorescent nitroxide probe.

PubMed

Miljevic, B; Heringa, M F; Keller, A; Meyer, N K; Good, J; Lauber, A; Decarlo, P F; Fairfull-Smith, K E; Nussbaumer, T; Burtscher, H; Prevot, A S H; Baltensperger, U; Bottle, S E; Ristovski, Z D

2010-09-01

This study reports the potential toxicological impact of particles produced during biomass combustion by an automatic pellet boiler and a traditional logwood stove under various combustion conditions using a novel profluorescent nitroxide probe, BPEAnit. This probe is weakly fluorescent but yields strong fluorescence emission upon radical trapping or redox activity. Samples were collected by bubbling aerosol through an impinger containing BPEAnit solution, followed by fluorescence measurement. The fluorescence of BPEAnit was measured for particles produced during various combustion phases: at the beginning of burning (cold start), stable combustion after refilling with the fuel (warm start), and poor burning conditions. For particles produced by the logwood stove under cold-start conditions, significantly higher amounts of reactive species per unit of particulate mass were observed compared to emissions produced during a warm start. In addition, sampling of logwood burning emissions after passing through a thermodenuder at 250 degrees C resulted in an 80-100% reduction of the fluorescence signal of the BPEAnit probe, indicating that the majority of reactive species were semivolatile. Moreover, the amount of reactive species showed a strong correlation with the amount of particulate organic material. This indicates the importance of semivolatile organics in particle-related toxicity. Particle emissions from the pellet boiler, although of similar mass concentration, were not observed to lead to an increase in fluorescence signal during any of the combustion phases.

High Triterpenic Acids Production in Callus Cultures from Fruit Pulp of Two Apple Varieties.

PubMed

Verardo, Giancarlo; Gorassini, Andrea; Ricci, Donata; Fraternale, Daniele

2017-01-01

Very rarely fruit pulp has been used in in vitro culture to produce secondary metabolites useful in promoting health. The aims of this work were the study of the best conditions to obtain the callus cultures from the pulp of two varieties of apples, Golden Delicious (GD) and "Mela Rosa Marchigiana" (MRM), and the quali-quantitative analysis of secondary metabolites produced by the two in vitro callus cultures. Callus was induced on both Murashige and Skoog and Gamborg B5 media containing various combinations of supplements. To achieve the maximum recovery of secondary metabolites produced, preliminary extraction tests were carried out on GD apple culture using two different organic solvents (MeOH and EtOAc). The quali-quantitative analysis of the methanolic extract of both cultures was carried out by ESI-MS n and GC-MS techniques. The GC-MS analysis revealed the presence of triterpenic acids, in particular, oleanolic, ursolic, maslinic, pomolic, tormentic, corosolic and annurcoic acid along with a phytosterol, β-sitosterol. In addition, GD callus culture produced phloridzin, absent in the MRM culture. In this last culture, however, the total amount of secondary metabolites was markedly higher. The in vivo production of these bioactive compounds were also quantified in the GD and MRM apple pulps. Apple pulps produced higher amounts of triterpenic acids in vitro than in vivo. The present work can be considered a method to amplify the production of important secondary metabolites which exert beneficial effects on human health. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Biohydrogen production by dark fermentation of glycerol using Enterobacter and Citrobacter Sp.

PubMed

Maru, Biniam T; Constanti, Magda; Stchigel, Alberto M; Medina, Francesc; Sueiras, Jesus E

2013-01-01

Glycerol is an attractive substrate for biohydrogen production because, in theory, it can produce 3 mol of hydrogen per mol of glycerol. Moreover, glycerol is produced in substantial amounts as a byproduct of producing biodiesel, the demand for which has increased in recent years. Therefore, hydrogen production from glycerol was studied by dark fermentation using three strains of bacteria: namely, Enterobacter spH1, Enterobacter spH2, and Citrobacter freundii H3 and a mixture thereof (1:1:1). It was found that, when an initial concentration of 20 g/L of glycerol was used, all three strains and their mixture produced substantial amounts of hydrogen ranging from 2400 to 3500 mL/L, being highest for C. freundii H3 (3547 mL/L) and Enterobacter spH1 (3506 mL/L). The main nongaseous fermentation products were ethanol and acetate, albeit in different ratios. For Enterobacter spH1, Enterobacter spH2, C. freundii H3, and the mixture (1:1:1), the ethanol yields (in mol EtOH/mol glycerol consumed) were 0.96, 0.67, 0.31, and 0.66, respectively. Compared to the individual strains, the mixture (1:1:1) did not show a significantly higher hydrogen level, indicating that there was no synergistic effect. Enterobacter spH1 was selected for further investigation because of its higher yield of hydrogen and ethanol. Copyright © 2012 American Institute of Chemical Engineers (AIChE).

Conventional development versus managed growth: the costs of sprawl.

PubMed

Burchell, Robert W; Mukherji, Sahan

2003-09-01

We examined the effects of sprawl, or conventional development, versus managed (or "smart") growth on land and infrastructure consumption as well as on real estate development and public service costs in the United States. Mathematical impact models were used to produce US estimates of differences in resources consumed according to each growth scenario over the period 2000-2025. Sprawl produces a 21% increase in amount of undeveloped land converted to developed land (2.4 million acres) and approximately a 10% increase in local road lane-miles (188 300). Furthermore, sprawl causes about 10% more annual public service (fiscal) deficits ($4.2 billion US dollars) and 8% higher housing occupancy costs ($13 000 US dollars per dwelling unit). Managed growth can save significant amounts of human and natural resources with limited effects on traditional development procedures.

Conventional Development Versus Managed Growth: The Costs of Sprawl

PubMed Central

Burchell, Robert W.; Mukherji, Sahan

2003-01-01

Objectives. We examined the effects of sprawl, or conventional development, versus managed (or “smart”) growth on land and infrastructure consumption as well as on real estate development and public service costs in the United States. Methods. Mathematical impact models were used to produce US estimates of differences in resources consumed according to each growth scenario over the period 2000–2025. Results. Sprawl produces a 21% increase in amount of undeveloped land converted to developed land (2.4 million acres) and approximately a 10% increase in local road lane-miles (188 300). Furthermore, sprawl causes about 10% more annual public service (fiscal) deficits ($4.2 billion) and 8% higher housing occupancy costs ($13 000 per dwelling unit). Conclusions. Managed growth can save significant amounts of human and natural resources with limited effects on traditional development procedures. PMID:12948976

Genetic manipulation of the metabolism of polyamines in poplar cells. The regulation of putrescine catabolism

Treesearch

Pratiksha Bhatnagar; Rakesh Minocha; Subhash C. Minocha

2002-01-01

We investigated the catabolism of putrescine (Put) in a non-transgenic (NT) and a transgenic cell line of poplar (Populus nigra x maximowiczii) expressing a mouse (Mus musculus) ornithine (Orn) decarboxylase (odc) cDNA. The transgenic cells produce 3- to 4-fold higher amounts of Put than the NT...

Information Literacy and the 21st Century Academic Librarian: A Delphi Study

ERIC Educational Resources Information Center

Dixon-Thomas, Courtlann

2012-01-01

An emphasis on instruction has been growing in libraries as a result of the cumbersome amount of information that is produced and available globally. This, coupled with the growing diverse student populations and the demand for higher education, has created the need for students entering the workforce who can think critically, adapt quickly and…

Evaluation of Beer Fermentation with a Novel Yeast
Williopsis saturnus.

PubMed

Liu, Shao-Quan; Quek, Althea Ying Hui

2016-12-01

The aim of this study is to evaluate the potential of a novel yeast Williopsis saturnus var. mrakii NCYC 500 to produce fruity beer. Fermentation performance of W. mrakii and beer volatile composition were compared against that fermented with Saccharomyces cerevisiae Safale US-05. o Brix, sugar and pH differed significantly between the two types of beer. A total of 8 alcohols, 11 acids, 41 esters, 9 aldehydes, 8 ketones, 21 terpenes and terpenoids, 5 Maillard reaction products and 2 volatile phenolic compounds were detected. Yeast strain Safale US-05 was more capable of producing a wider range of ethyl and other esters, while yeast strain NCYC 500 produced significantly higher amounts of acetate esters. Strain NCYC 500 retained more terpenes and terpenoids, suggesting that the resultant beer could possess more of the aromatic hint of hops. This study showed that W. saturnus var. mrakii NCYC 500 could ferment wort to produce low-alcohol beer with higher levels of acetate esters, terpenes and terpenoids than yeast S. cerevisiae Safale US-05.

Acid Pretreatment of Sago Wastewater for Biohydrogen Production

NASA Astrophysics Data System (ADS)

Illi Mohamad Puad, Noor; Rahim, Nurainin Farhan Abd; Suhaida Azmi, Azlin

2018-03-01

Biohydrogen has been recognized to be one of the future renewable energy sources and has the potential in solving the greenhouse effects. In this study, Enterobacter aerogenes (E. aerogenes) was used as the biohydrogen producer via dark fermentation process using sago wastewater as the substrate. However, pretreatment of sago wastewater is required since it consists of complex sugars that cannot be utilized directly by the bacteria. This study aimed to use acid pretreatment method to produce high amount of glucose from sago wastewater. Three different types of acid: sulfuric acid (H2SO4); hydrochloric acid (HCl) and nitric acid (HNO3) were screened for the best acid in producing a maximum amount of glucose. H2SO4 gave the highest amount of glucose which was 9.406 g/L. Design of experiment was done using Face-centred Central Composite Design (FCCCD) tool under Response Surface Methodology (RSM) in Design Expert 9 software. The maximum glucose (9.138 g/L) was recorded using 1 M H2SO4 at 100 °C for 60 min. A batch dark fermentation using E. aerogenes was carried out and it was found that pretreated sago wastewater gave a higher hydrogen concentration (1700 ppm) compared to the raw wastewater (410 ppm).

Hairy root culture optimization and resveratrol production from Vitis vinifera subsp. sylvesteris.

PubMed

Hosseini, Sayed Mehdi; Bahramnejad, Bahman; Douleti Baneh, Hamed; Emamifar, Aryo; Goodwin, Paul H

2017-04-01

Resveratrol is a polyphenolic compound produced in very low levels in grapes. To achieve high yield of resveratrol in wild grape, three Agrobacterium rhizogenes strains, Ar318, ArA4 and LBA9402, were used to induce hairy roots following infection of internodes, nodes or petioles of in vitro grown Vitis vinifera subsp. sylvesteris accessions W2 and W16, and cultivar Rasha. The effects of inoculation time, age of explants, bacterial concentration and co-cultivation times were examined on the efficiency of the production of hairy roots. Strains Ar318, ArA4 and LBA9402 all induced hairy roots in the tested genotypes, but the efficiency of ArA4 strain was higher than the other strains. The highest hairy root production was with using internodes as explants. The transformation of hairy roots lines was confirmed by PCR detection of rolB gene. Half Murashige and Skoog (MS) medium was better for biomass production compared with MS medium. HPLC analysis of resveratrol production in the hairy root cultures showed that all the genotypes produced higher amounts of resveratrol than control roots. The highest amount of resveratrol was produced from W16 internode cultures, which was 31-fold higher than that of control root. Furthermore, TLC analysis showed that treatments of hairy roots with sodium acetate and jasmonate elevated resveratrol levels both in hairy root tissue and excreted into the half MS medium. These results demonstrate that endogenous and exogenous factors can affect resveratrol production in hairy root culture of grape, and this strategy could be used to increase low resveratrol production in grapes.

Rye bran as fermentation matrix boosts in situ dextran production by Weissella confusa compared to wheat bran.

PubMed

Kajala, Ilkka; Mäkelä, Jari; Coda, Rossana; Shukla, Shraddha; Shi, Qiao; Maina, Ndegwa Henry; Juvonen, Riikka; Ekholm, Päivi; Goyal, Arun; Tenkanen, Maija; Katina, Kati

2016-04-01

The consumption of fiber-rich foods such as cereal bran is highly recommended due to its beneficial health effects. Pre-fermentation of bran with lactic acid bacteria can be used to improve the otherwise impaired flavor and textural qualities of bran-rich products. These positive effects are attributed to enzymatic modification of bran components and the production of functional metabolites like organic acids and exopolysaccharides such as dextrans. The aim of this study was to investigate dextran production in wheat and rye bran by fermentation with two Weissella confusa strains. Bran raw materials were analyzed for their chemical compositions and mineral content. Microbial growth and acidification kinetics were determined from the fermentations. Both strains produced more dextran in rye bran in which the fermentation-induced acidification was slower and the acidification lag phase longer than in wheat bran. Higher dextran production in rye bran is expected to be due to the longer period of optimal pH for dextran synthesis during fermentation. The starch content of wheat bran was higher, which may promote isomaltooligosaccharide formation at the expense of dextran production. W. confusa Cab3 produced slightly higher amounts of dextran than W. confusa VTT E-90392 in all raw materials. Fermentation with W. confusa Cab3 also resulted in lower residual fructose content which has technological relevance. The results indicate that wheat and particularly rye bran are promising matrices for producing technologically significant amounts of dextran, which facilitates the use of nutritionally valuable raw bran in food applications.

Study of Fungal Colonization of Wheat Kernels in Syria with a Focus on Fusarium Species

PubMed Central

Alkadri, Dima; Nipoti, Paola; Döll, Katharina; Karlovsky, Petr; Prodi, Antonio; Pisi, Annamaria

2013-01-01

Wheat is one of the main crops in Mediterranean countries, and its cultivation has an important role in the Syrian economy. In Syria, Fusarium head blight (FHB) has not been reported so far. Mycological analysis of 48 samples of wheat kernels collected from cultivation areas with different climatic conditions were performed in 2009 and 2010. Fungal isolates were identified at the genus level morphologically; Fusarium species were characterized morphologically and by species-specific PCR. The most frequent fungal genera found were Alternaria spp. and Cladosporium spp., with frequencies of 24.7% and 8.1%, respectively, while the frequency of Fusarium spp. was 1.5% of kernels. Most frequent Fusarium species were F. tricinctum (30% of all Fusarium isolates), F. culmorum (18%), F. equiseti (14%) and F. graminearum (13%). The mycotoxin production potential of selected Fusarium isolates was assessed by HPLC-MS analysis of rice cultures; chemotyping by PCR was carried out for comparison. All six F. graminearum strains tested produced small amounts (<3 mg/kg) of nivalenol (NIV). All ten F. culmorum strains tested produced large amounts of trichothecenes (>100 mg/kg); four strains produced NIV and six strains produced deoxynivalenol (DON) and 3-acetyl-deoxynivalenol (3Ac-DON). PCR chemotyping lead to an oversimplified picture, because all 3Ac-DON chemotype strains produced more DON than 3Ac-DON; furthermore, the strongest NIV producers produced significant amounts of DON. All tested strains of F. culmorum, F. graminearum, F. pseudograminearum (two strains) and most F. equiseti strains (five of six strains) produced zearalenone. Grains of durum wheat were more frequently colonized by Fusarium spp. than grains of soft wheat. Incidence of Fusarium spp. in irrigated fields was higher than in rainfed fields. The incidence of Fusarium strains producing mycotoxins raises concerns about the risk of Fusarium head blight to Syria and its consequences for public health. PMID:23493058

Somatic Coliphage Profiles of Produce and Environmental Samples from Farms in Northern México.

PubMed

Bartz, Faith E; Hodge, Domonique Watson; Heredia, Norma; de Aceituno, Anna Fabiszewski; Solís, Luisa; Jaykus, Lee-Ann; Garcia, Santos; Leon, Juan S

2016-09-01

Somatic coliphages were quantified in 459 produce and environmental samples from 11 farms in Northern Mexico to compare amounts of somatic coliphages among different types of fresh produce and environmental samples across the production steps on farms. Rinsates from cantaloupe melons, jalapeño peppers, tomatoes, and the hands of workers, soil, and water were collected during 2011-2012 at four successive steps on each farm, from the field before harvest through the packing facility, and assayed by FastPhage MPN Quanti-tray method. Cantaloupe farm samples contained more coliphages than jalapeño or tomato (p range <0.01-0.03). Across production steps, jalapeños had higher coliphage percentages before harvest than during packing (p = 0.03), while tomatoes had higher coliphage concentrations at packing than all preceding production steps (p range <0.01-0.02). These findings support the use of targeted produce-specific interventions at multiple points in the process of growing and packing produce to reduce the risk of enteric virus contamination and improve food safety during fruit and vegetable production.

Exopolysaccharide-producing lactic acid bacteria strains from traditional Thai fermented foods: isolation, identification and exopolysaccharide characterization.

PubMed

Smitinont, T; Tansakul, C; Tanasupawat, S; Keeratipibul, S; Navarini, L; Bosco, M; Cescutti, P

1999-10-15

Lactic Acid Bacteria (LAB) isolated from various traditional Thai fermented foods were screened for exopolysaccharides (EPS) production. From 104 isolates, two rod-shaped and five coccal-shaped LAB were able to produce EPS from sucrose on solid media. However, only the cocci were capable of producing EPS in liquid media and these were identified as Pediococcus pentosaceus. Pediococcus pentosaceus strains AP-1 and AP-3 produced EPS in high yield. In liquid media containing sucrose as carbon source, the amount of EPS produced by AP-1 and AP-3 strains was 6.0 and 2.5 g/L, respectively. The isolated and purified EPSs were chemically characterized. On the basis of sugar composition, methylation analysis and nuclear magnetic resonance spectroscopy, both the EPSs were shown to belong to the same dextran class. In particular, both EPSs differed from linear dextran by branching through 3,6-di-Osubstituted alpha-D-glucopyranosyl residues. The EPS from P. pentosaceus AP-3 was characterized by a relatively higher degree of branching and by a higher molecular weight than that from P. pentosaceus AP-1.

Relationships of flour solvent retention capacity, secondary structure and rheological properties with the cookie making characteristics of wheat cultivars.

PubMed

Kaur, Amritpal; Singh, Narpinder; Kaur, Seeratpreet; Ahlawat, Arvind Kumar; Singh, Anju Mahendru

2014-09-01

The relationships of grain, flour solvent retention capacity (SRC) and dough rheological properties with the cookie making properties of wheat cultivars were evaluated. Cultivars with higher proportion of intermolecular-β-sheets+antiparallel β sheets and lower α-helix had greater gluten strength. The grain weight and diameter positively correlated with the proportion of fine particles and the cookie spread factor (SF) and negatively to the grain hardness (GH) and Na2CO3 SRC. The SF was higher in the flour with a higher amount of fine particle and with a lower Na2CO3 SRC and dough stability (DS). The breaking strength (BS) of cookies was positively correlated to lactic acid (LA) SRC, DS, peak time, sedimentation value (SV), G' and G″. Na2CO3 SRC and GH were strongly correlated. The gluten performance index showed a strong positive correlation with SV, DS, G' and G″. The water absorption had a significant positive correlation with sucrose SRC and LASRC. Cultivars with higher GH produced higher amount of coarse particles in flours that had higher Na2CO3 SRC and lower cookie SF. Copyright © 2014 Elsevier Ltd. All rights reserved.

Study on the pollution status and control measures for the livestock and poultry breeding industry in northeastern China.

PubMed

Wang, Hanxi; Xu, Jianling; Liu, Xuejun; Sheng, Lianxi; Zhang, Di; Li, Longwei; Wang, Aixia

2018-02-01

Livestock and poultry breeding industry is one of the main economic pillars of northeastern China. However, the amount of pollutants produced is much higher than that in other parts of China. Through a questionnaire survey, indoor experiment, and outdoor experiment, it was found that the resource utilization rate of livestock and poultry manure in the northeastern region is low, with the pollution of livestock and poultry breeding mainly including air and water pollution. The alarm level of cultivated land and manure is II. While the livestock and poultry breeding is relatively concentrated area, its level is higher than grade II. Based on the pollution status of small farms, biogas can be produced through fermentation, along with the preparation of organic fertilizer, to completely utilize the manure and straw, while obtaining higher economic value, and effectively controlling the pollution from livestock and poultry breeding.

Changes in Trace Gas Nitrogen Emissions as a Response to Ecosystem Type Conversion in a Semi-Arid Climate.

NASA Astrophysics Data System (ADS)

Andrews, H.; Eberwein, J. R.; Jenerette, D.

2016-12-01

As humans continue to introduce exotic plants and to alter climate and fire regimes in semi-arid ecosystems, many plant communities have begun to shift from perennial forbs and shrubs to annual grasses with different functional traits. Shifts in plant types are also associated with shifts in microclimate, microbial activity, and litter inputs, all of which contribute to the efficiency of nitrogen processing and the magnitude of trace gas emissions (NOx and N2O), which are increasingly important fluxes in water-limited systems. Here, we explored how changes in plant litter impact trace gas emissions, asking the question: How does conversion from a native shrubland to exotic grassland ecosystem alter NOx and N2O fluxes in a semi-arid climate? We posed two hypotheses to explain the impacts of different types of litter on soils disturbed by exotic grasses and those that were still considered shrublands: 1.) Soils that have undergone conversion by exotic grasses release higher amounts of NOx and N2O than do those of unconverted shrublands, due to disruptions of native plant and soil processes by exotic grasses, and 2.) Because litter of exotic grasses has lower C:N than that of shrubs, litter inputs from exotic grasses will increase NOx and N2O emissions from soils more than will litter inputs from shrubs. As a preliminary study, we experimentally wetted mesocosms in a laboratory incubation containing converted and unconverted soils that had been mixed with no litter or either exotic grass or coastal sage scrub (CSS) litter. We measured N2O fluxes from mesocosms over a 48-hour period. 24 hours after wetting, samples with grass litter produced higher amounts of N2O than those with CSS litter; similarly, converted soils produced higher amounts of N2O than unconverted soils. These two effects combined resulted in exotic grassland conditions (converted soils with exotic grass litter) producing 10 times the amount of N2O as those containing native shrubland conditions (unconverted soils with CSS litter). Additionally, soils with no litter peaked in N2O emissions earlier than those with litter (12 hours after wetting compared to 24 hours after wetting). Following preliminary results, we suggest that differences in plant traits, such as litter, play a significant role in the magnitude and timing of trace gas nitrogen emissions.

The Draft Genome Sequence of a Novel High-Efficient Butanol-Producing Bacterium Clostridium Diolis Strain WST.

PubMed

Chen, Chaoyang; Sun, Chongran; Wu, Yi-Rui

2018-03-21

A wild-type solventogenic strain Clostridium diolis WST, isolated from mangrove sediments, was characterized to produce high amount of butanol and acetone with negligible level of ethanol and acids from glucose via a unique acetone-butanol (AB) fermentation pathway. Through the genomic sequencing, the assembled draft genome of strain WST is calculated to be 5.85 Mb with a GC content of 29.69% and contains 5263 genes that contribute to the annotation of 5049 protein-coding sequences. Within these annotated genes, the butanol dehydrogenase gene (bdh) was determined to be in a higher amount from strain WST compared to other Clostridial strains, which is positively related to its high-efficient production of butanol. Therefore, we present a draft genome sequence analysis of strain WST in this article that should facilitate to further understand the solventogenic mechanism of this special microorganism.

Chemical changes associated with the invasion of a Melipona scutellaris colony by Melipona rufiventris workers.

PubMed

Pianaro, Adriana; Flach, Adriana; Patricio, Eda F L R A; Nogueira-Neto, Paulo; Marsaioli, Anita J

2007-05-01

Wax constituents produced by worker bees and the chemistry of the nest batumen (mixture of wax, mud, and floral materials) in a Melipona scutellaris colony changed when it was invaded by Melipona rufiventris workers. Gas chromatography/mass spectrometry analyses showed that after invasion, the M. scutellaris workers of the invaded colony produced waxes with higher relative abundance of triacontanyl acetate and decreased the amounts of n-alkanes and n-9-alkenes. On the other hand, waxes from M. rufiventris workers displayed few changes. The change in the composition of the M. scutellaris waxes chemically differentiates that species from the M. rufiventris invader workers. Comparative analyses of batumens samples from pure and invaded colonies revealed greater amounts of terpenes and phenolic derivatives in the batumen from the invaded colony. This is the first report on the chemical characterization of batumens from stingless bees.

Education and Synthetic Work-Life Earnings Estimates. American Community Survey Reports. ACS-14

ERIC Educational Resources Information Center

Julian, Tiffany; Kominski, Robert

2011-01-01

The relationship between education and earnings is a long-analyzed topic of study. Generally, there is a strong belief that achievement of higher levels of education is a well established path to better jobs and better earnings. This report provides one view of the economic value of educational attainment by producing an estimate of the amount of…

Production of Higher Alcohols During Indonesian Tapé Ketan Fermentation †

PubMed Central

Cronk, T. C.; Mattick, L. R.; Steinkraus, K. H.; Hackler, L. R.

1979-01-01

A study was made of the higher alcohols (fusel oils) produced during the Indonesian tapé ketan fermentation using Amylomyces rouxii as the principal mold, alone or in combination with yeasts belonging to genera commonly found in the tapé ketan fermentation (Endomycopsis, Candida, and Hansenula). Total fusel oils increased with length of fermentation. Fusel oils detected in the product distillate included isobutanol and isoamyl and active amyl alcohols. No n-propanol was detected. Isobutanol and isoamyl alcohols were formed in the largest amounts. A. rouxii alone produced nearly the same quantity of fusel oils (total production, 275 mg/liter at 192 h) as it did in combination with Endomycopsis burtonii (total production, 292 mg/liter at 192 h).A. rouxii and Endomycopsis fibuliger produced fusel oils totaling 72 mg/liter at 32 h and 558 mg/liter at 192 h. A. rouxii in combination with Candida yeasts produced somewhat more fusel oils, ranging from 590 to 618 mg/liter at 192 h. A. rouxii in combination with Hansenula yeasts produced the least fusel oils, totaling 143 to 248 mg/liter at 192 h. During the first 36 h, production of fusel oils was higher at 30 and 35°C than at 25°C. At 48 h fusel oil production was slightly higher at 30°C than at 35°C. Beyond 48 h, production of fusel oils was higher at 25°C. A. rouxii in combination with Hansenula anomala and Hansenula subpelliculosa produced considerable ethyl acetate, ranging from 145 to 199 mg/liter at 36 h and 354 to 369 mg/liter at 192 h. PMID:16345385

Co-pyrolysis of rice straw and Polyethylene Terephthalate (PET) using a fixed bed drop type pyrolyzer

NASA Astrophysics Data System (ADS)

Izzatie, N. I.; Basha, M. H.; Uemura, Y.; Hashim, M. S. M.; Amin, N. A. M.; Hamid, M. F.

2017-10-01

In this work, co-pyrolysis of rice straw and polyethylene terephthalate (PET) was carried out at different temperatures (450,500,550, and 600°C) at ratio 1:1 by using fixed bed drop-type pyrolyzer. The purpose of this work is to determine the effect of pyrolysis temperature on the product yield. As the temperature increased, the pyrolysis oil increased until it reaches certain high temperature (600°C), the pyrolysis oil decreased as of more NCG were produced. The temperature 550°C is considered as the optimum pyrolysis temperature since it produced the highest amount of pyrolysis oil with 36 wt.%. In pyrolysis oil, the calorific value (13.98kJ/g) was low because of the presence of high water content (52.46 wt.%). Main chemicals group from pyrolysis oil were an aldehyde, ketones, acids, aromatics, and phenol and all compound have abundant of hydrogen and carbon were identified. Co-pyrolysis of rice straw and PET produced a higher amount of carbon oxides and recycling back the NCG could increase liquid and char yields.

The Influence of Friction Between Football Helmet and Jersey Materials on Force: A Consideration for Sport Safety

PubMed Central

Rossi, Anthony M.; Claiborne, Tina L.; Thompson, Gregory B.; Todaro, Stacey

2016-01-01

Context: The pocketing effect of helmet padding helps to dissipate forces experienced by the head, but if the player's helmet remains stationary in an opponent's shoulder pads, the compressive force on the cervical spine may increase. Objective: To (1) measure the coefficient of static friction between different football helmet finishes and football jersey fabrics and (2) calculate the potential amount of force on a player's helmet due to the amount of friction present. Design: Cross-sectional study. Setting: Laboratory. Patients or Other Participants: Helmets with different finishes and different football jersey fabrics. Main Outcome Measure(s): The coefficient of friction was determined for 2 helmet samples (glossy and matte), 3 football jerseys (collegiate, high school, and youth), and 3 types of jersey numbers (silkscreened, sublimated, and stitched on) using the TAPPI T 815 standard method. These measurements determined which helmet-to-helmet, helmet-to-jersey number, and helmet-to-jersey material combination resulted in the least amount of static friction. Results: The glossy helmet versus glossy helmet combination produced a greater amount of static friction than the other 2 helmet combinations (P = .013). The glossy helmet versus collegiate jersey combination produced a greater amount of static friction than the other helmet-to-jersey material combinations (P < .01). The glossy helmet versus silkscreened numbers combination produced a greater amount of static friction than the other helmet-to-jersey number combinations (P < .01). Conclusions: The force of static friction experienced during collisions can be clinically relevant. Conditions with higher coefficients of static friction result in greater forces. In this study, the highest coefficient of friction (glossy helmet versus silkscreened number) could increase the forces on the player's helmet by 3553.88 N when compared with other helmet-to-jersey combinations. Our results indicate that the makeup of helmet and uniform materials may affect sport safety. PMID:27824251

Is There Any Difference between the In Situ and Systemic IL-10 and IFN-γ Production when Clinical Forms of Cutaneous Sporotrichosis Are Compared?

PubMed

Morgado, Fernanda N; Schubach, Armando O; Pimentel, Maria Inês; Lyra, Marcelo R; Vasconcellos, Érica C F; Valete-Rosalino, Claudia M; Conceição-Silva, Fátima

2016-01-01

Fungus of the Sporothrix schenckii complex can produce skin lesions in humans, commonly lymphocutaneous (LC) and fixed (F) forms of sporotrichosis. Some authors have suggested that clinical forms are influenced by differences in virulence and genetic profile of isolates. But little is known about the role of immune response in determining the clinical outcome of sporotrichosis. To verify the profile of systemic and in situ IFN-γ and IL-10 expression in sporotrichosis patients, and consequently to detect any difference between the two compartments and/or clinical presentation, we quantified the number of IFN-γ and IL-10 producer peripheral blood mononuclear cells stimulated with S. schenckii antigen (Ss-Ag) by Elispot, and quantified cytokines expression by in situ immunohistochemistry in the same patient. Three groups were formed: 1- LC (n = 9); 2- F (n = 10); 3- healthy individuals (n = 14). All sporotrichosis patients produced high amounts of systemic IFN- γ when compared to uninfected individuals. No differences were observed between LC and F groups. Regarding in situ IL-10 expression, a difference between LC and F groups was observed: LC lesions presented higher amounts of IL-10 than F lesions differently from systemic IL-10 which showed similarities. Our data suggests that LC lesions present higher IL-10 expression which could be related to regulatory mechanisms for compensating the tissue injury, however favoring fungal persistence in the lesions. Surprisingly, there were no differences in systemic and in situ IFN- γ expression between CL and F patients, although it was significantly higher expressed in these patients than in healthy individuals.

Is There Any Difference between the In Situ and Systemic IL-10 and IFN-γ Production when Clinical Forms of Cutaneous Sporotrichosis Are Compared?

PubMed Central

Morgado, Fernanda N.; Schubach, Armando O.; Pimentel, Maria Inês; Lyra, Marcelo R.; Vasconcellos, Érica C. F.; Valete-Rosalino, Claudia M.; Conceição-Silva, Fátima

2016-01-01

Fungus of the Sporothrix schenckii complex can produce skin lesions in humans, commonly lymphocutaneous (LC) and fixed (F) forms of sporotrichosis. Some authors have suggested that clinical forms are influenced by differences in virulence and genetic profile of isolates. But little is known about the role of immune response in determining the clinical outcome of sporotrichosis. To verify the profile of systemic and in situ IFN-γ and IL-10 expression in sporotrichosis patients, and consequently to detect any difference between the two compartments and/or clinical presentation, we quantified the number of IFN-γ and IL-10 producer peripheral blood mononuclear cells stimulated with S. schenckii antigen (Ss-Ag) by Elispot, and quantified cytokines expression by in situ immunohistochemistry in the same patient. Three groups were formed: 1- LC (n = 9); 2- F (n = 10); 3- healthy individuals (n = 14). All sporotrichosis patients produced high amounts of systemic IFN- γ when compared to uninfected individuals. No differences were observed between LC and F groups. Regarding in situ IL-10 expression, a difference between LC and F groups was observed: LC lesions presented higher amounts of IL-10 than F lesions differently from systemic IL-10 which showed similarities. Our data suggests that LC lesions present higher IL-10 expression which could be related to regulatory mechanisms for compensating the tissue injury, however favoring fungal persistence in the lesions. Surprisingly, there were no differences in systemic and in situ IFN- γ expression between CL and F patients, although it was significantly higher expressed in these patients than in healthy individuals. PMID:27622513

Enzymatic lignocellulose hydrolysis: Improved cellulase productivity by insoluble solids recycling

PubMed Central

2013-01-01

Background It is necessary to develop efficient methods to produce renewable fuels from lignocellulosic biomass. One of the main challenges to the industrialization of lignocellulose conversion processes is the large amount of cellulase enzymes used for the hydrolysis of cellulose. One method for decreasing the amount of enzyme used is to recycle the enzymes. In this study, the recycle of enzymes associated with the insoluble solid fraction after the enzymatic hydrolysis of cellulose was investigated for pretreated corn stover under a variety of recycling conditions. Results It was found that a significant amount of cellulase activity could be recovered by recycling the insoluble biomass fraction, and the enzyme dosage could be decreased by 30% to achieve the same glucose yields under the most favorable conditions. Enzyme productivity (g glucose produced/g enzyme applied) increased between 30 and 50% by the recycling, depending on the reaction conditions. While increasing the amount of solids recycled increased process performance, the methods applicability was limited by its positive correlation with increasing total solids concentrations, reaction volumes, and lignin content of the insoluble residue. However, increasing amounts of lignin rich residue during the recycle did not negatively impact glucose yields. Conclusions To take advantage of this effect, the amount of solids recycled should be maximized, based on a given processes ability to deal with higher solids concentrations and volumes. Recycling of enzymes by recycling the insoluble solids fraction was thus shown to be an effective method to decrease enzyme usage, and research should be continued for its industrial application. PMID:23336604

Particles and Zinc on the Absorbed Impact Energy of Gravity Cast Aluminum Matrix Composites

NASA Astrophysics Data System (ADS)

Corchado, Marcos; Reyes, Fernando; Suárez, Oscar Marcelo

2014-06-01

The effect of different amounts of boron, in the form of AlB2 particles, as well as zinc concentration in a gravity cast Al-B-Zn composite, was studied and related to the absorbed energy upon fracture during Charpy impact experiments. In addition, the authors correlated the composite Brinell hardness with the quantitative assessment of brittle and ductile fracture areas of the Charpy fractured specimens and found that increasing AlB2 particle concentration resulted in a reduction of absorbed impact energy. Although larger zinc levels produced somewhat similar results, the AlB2 effect was prevalent. The energy absorption upon impact reached a maximum when no particles were present; conversely, the lowest amount of absorbed energy corresponded to a composite with a composition of 15 wt.% Zn and 8% in volume of AlB2, i.e., the highest concentration of AlB2 and zinc studied. Raising the amount of AlB2 as well as zinc, as expected, resulted in higher Brinell hardness. A statistical analysis allowed studying of the particle size distribution, whereas values for crack tip opening displacement were subsequently calculated for the range of particle sizes found and the corresponding AlB2 particle volume percent. Higher porosity values were measured for larger AlB2 volume percent. Finally, analyses of fracture surfaces corroborated that brittle fracture was favored in composites with higher amounts of AlB2 and zinc.

Distribution, Characteristics, and Biotic Availability of Fallout, Operation Plumbbob

DTIC Science & Technology

1957-10-01

hours. Balloon mounted detonations produced fallout debris of higher water and acid solubility than did tower mounted detonations. The percentage of Sr89...of these radLoelements in fallout debris from balloon detonations than from tower detonations. The amounts of water- soluble Ba140 and Sr89, 90...99 5.3.1 Magnetic Properties ........................ 99 5.3.2 Solubility .............................. 100 5.3.2.1

Soybean-Enriched Snacks Based on African Rice

PubMed Central

Marengo, Mauro; Akoto, Hannah F.; Zanoletti, Miriam; Carpen, Aristodemo; Buratti, Simona; Benedetti, Simona; Barbiroli, Alberto; Johnson, Paa-Nii T.; Sakyi-Dawson, Esther O.; Saalia, Firibu K.; Bonomi, Francesco; Pagani, Maria Ambrogina; Manful, John; Iametti, Stefania

2016-01-01

Snacks were produced by extruding blends of partially-defatted soybean flour with flours from milled or parboiled African-grown rice. The interplay between composition and processing in producing snacks with a satisfactory sensory profile was addressed by e-sensing, and by molecular and rheological approaches. Soybean proteins play a main role in defining the properties of the protein network in the products. At the same content in soybean flour, use of parboiled rice flour increases the snack’s hardness. Electronic nose and electronic tongue discriminated samples containing a higher amount of soybean flour from those with a lower soybean flour content. PMID:28231133

Soybean-Enriched Snacks Based on African Rice.

PubMed

Marengo, Mauro; Akoto, Hannah F; Zanoletti, Miriam; Carpen, Aristodemo; Buratti, Simona; Benedetti, Simona; Barbiroli, Alberto; Johnson, Paa-Nii T; Sakyi-Dawson, Esther O; Saalia, Firibu K; Bonomi, Francesco; Pagani, Maria Ambrogina; Manful, John; Iametti, Stefania

2016-05-20

Snacks were produced by extruding blends of partially-defatted soybean flour with flours from milled or parboiled African-grown rice. The interplay between composition and processing in producing snacks with a satisfactory sensory profile was addressed by e-sensing, and by molecular and rheological approaches. Soybean proteins play a main role in defining the properties of the protein network in the products. At the same content in soybean flour, use of parboiled rice flour increases the snack's hardness. Electronic nose and electronic tongue discriminated samples containing a higher amount of soybean flour from those with a lower soybean flour content.

Evaluation of Beer Fermentation with a Novel Yeast
Williopsis saturnus

PubMed Central

Quek, Althea Ying Hui

2016-01-01

Summary The aim of this study is to evaluate the potential of a novel yeast Williopsis saturnus var. mrakii NCYC 500 to produce fruity beer. Fermentation performance of W. mrakii and beer volatile composition were compared against that fermented with Saccharomyces cerevisiae Safale US-05. oBrix, sugar and pH differed significantly between the two types of beer. A total of 8 alcohols, 11 acids, 41 esters, 9 aldehydes, 8 ketones, 21 terpenes and terpenoids, 5 Maillard reaction products and 2 volatile phenolic compounds were detected. Yeast strain Safale US-05 was more capable of producing a wider range of ethyl and other esters, while yeast strain NCYC 500 produced significantly higher amounts of acetate esters. Strain NCYC 500 retained more terpenes and terpenoids, suggesting that the resultant beer could possess more of the aromatic hint of hops. This study showed that W. saturnus var. mrakii NCYC 500 could ferment wort to produce low-alcohol beer with higher levels of acetate esters, terpenes and terpenoids than yeast S. cerevisiae Safale US-05. PMID:28115897

Premixed calcium silicate cement for endodontic applications

PubMed Central

Persson, Cecilia; Engqvist, Håkan

2011-01-01

Calcium silicate-based materials (also called MTA) are increasingly being used in endodontic applications. However, the handling properties of MTA are not optimal when it comes to injectability and cohesion. Premixing the cements using glycerol avoids these issues. However, there is a lack of data on the effect of common cement variables on important properties of premixed cements for endodontic applications. In this study, the effects of liquid-to-powder ratio, amount of radiopacifier and amount of calcium sulfate (added to control the setting time) were screened using a statistical model. In the second part of the study, the liquid-to-powder ratio was optimized for cements containing three different amounts of radiopacifier. Finally, the effect of using glycerol rather than water was evaluated in terms of radiopacity. The setting time was found to increase with the amount of radiopacifier when the liquid-to-powder ratio was fixed. This was likely due to the higher density of the radiopacifier in comparison to the calcium silicate, which gave a higher liquid-to-powder ratio in terms of volume. Using glycerol rather than water to mix the cements led to a decrease in radiopacity of the cement. In conclusion, we were able to produce premixed calcium silicate cements with acceptable properties for use in endodontic applications. PMID:23507729

Premixed calcium silicate cement for endodontic applications: injectability, setting time and radiopacity.

PubMed

Persson, Cecilia; Engqvist, Håkan

2011-01-01

Calcium silicate-based materials (also called MTA) are increasingly being used in endodontic applications. However, the handling properties of MTA are not optimal when it comes to injectability and cohesion. Premixing the cements using glycerol avoids these issues. However, there is a lack of data on the effect of common cement variables on important properties of premixed cements for endodontic applications. In this study, the effects of liquid-to-powder ratio, amount of radiopacifier and amount of calcium sulfate (added to control the setting time) were screened using a statistical model. In the second part of the study, the liquid-to-powder ratio was optimized for cements containing three different amounts of radiopacifier. Finally, the effect of using glycerol rather than water was evaluated in terms of radiopacity. The setting time was found to increase with the amount of radiopacifier when the liquid-to-powder ratio was fixed. This was likely due to the higher density of the radiopacifier in comparison to the calcium silicate, which gave a higher liquid-to-powder ratio in terms of volume. Using glycerol rather than water to mix the cements led to a decrease in radiopacity of the cement. In conclusion, we were able to produce premixed calcium silicate cements with acceptable properties for use in endodontic applications.

Characteristics of alpha-glucosidase production from recombinant Aspergillus oryzae by membrane-surface liquid culture in comparison with various cultivation methods.

PubMed

Morita, Masakazu; Shimamura, Hiroko; Ishida, Natsuko; Imamura, Koreyoshi; Sakiyama, Takaharu; Nakanishi, Kazuhiro

2004-01-01

alpha-Glucosidase was produced using recombinant Aspergillus oryzae by membrane-surface liquid culture (MSLC), a method previously developed by the authors and the results compared with other methods, including shaking flask culture (SFC), agar-plate culture (APC), culture on urethane sponge supports (USC), and liquid surface culture (LSC) to determine possible reasons for the advantageous features of MSLC. When yeast extract was used as a nitrogen source, the amount of enzyme produced by MSLC was 5 or more times higher than those for SFC and LSC, but similar to that using APC. Enzyme production in USC was slightly lower than in MSLC and APC. Cell growth was similar irrespective of the cultivation method used. When NaNO3, a typical inorganic nitrogen source was used, enzyme production in all the cultures was lower than that using yeast extract. However, even using NaNO3, the amount of the enzyme produced by MSLC was 8 to 20 times higher than those by SFC, APC, USC, and LSC. Although cell growth using NaNO3 was similar to that for yeast extract in MSLC, it was markedly decreased in SFC, APC, and LSC. The reason for the difference in enzyme productivity for various cultivation methods using yeast extract and NaNO3 as a nitrogen source is discussed, on the basis of the experimental findings. The role of the oxygen transfer effect and gene expression levels in enzyme production were also examined.

Evidence of Multi-Component Ion Exchange in Dolomite Formation during Low Salinity Waterflooding

NASA Astrophysics Data System (ADS)

Srisuriyachai, Falan; Meekangwal, Suthida

2017-12-01

Low salinity waterflooding is a technique performed in many oil reservoirs around the globe. The technique is simply implemented by injecting water with very low ionic activity compared to formation water into an injection well. The injected water will increase reservoir pressure that is compulsory to drive oil moving toward production well. More than just maintaining reservoir pressure as obtained from conventional waterflooding, low salinity water creates shifting of surface condition, resulting in additional amount of liberated oil. Nevertheless, exact oil recovery mechanisms are still discussed. Among these proposed mechanisms, Multi-component Ion Exchange (MIE) together with wettability alteration is believed to be a major mechanism leading to higher oil recovery compared to conventional waterflooding. In this study, detection of calcium and magnesium ions which are Potential Determining Ions (PDI) for carbonate reservoirs are detected during the coreflood experiment. Dolomite rock sample is used to represent carbonate formation and detection of previously mentioned ions is performed by complexometric titration of the effluents. From the study, it is observed that during conventional waterflooding and low salinity waterflooding at low temperature of 30 degrees Celsius, calcium and magnesium ions in the produced water is increased compared to the amount of these ions in the injected water. This incremental of ions can be explained by the dissolution of calcium and magnesium from dolomite which is chemically composed of calcium magnesium carbonate. At this temperature, the portion of calcium ion is always less than magnesium ion even though the amount of calcium ion is higher than magnesium ion in injected water. However, at higher temperatures which are 50 and 70 degrees Celsius, ratio of calcium and magnesium ions in injected and produced water is reversed. Disappearance of magnesium ion in the effluent is more obvious especially at 70 degrees Celsius and by low salinity waterflooding. This can be explained that at lower temperature, calcium ion disappears to form of calcium carboxylate complex with oil and at higher temperature, magnesium ion disappears as magnesium can start to form magnesium carboxylate complex with oil and hence, the amount of both calcium and magnesium ions is decreased compared to lower temperature. In dolomite reservoir, since both calcium ions and magnesium ions are provided from dissolution mechanism, the benefit from multi-component ion exchange will occur at high temperature as both calcium and magnesium ions will be consumed for oil recovery mechanism.

Using Observations from GPM and CloudSat to Produce a Climatology of Precipitation over the Ocean

NASA Astrophysics Data System (ADS)

Hayden, L.; Liu, C.

2017-12-01

Satellite based instruments are essential to the observation of precipitation at a global scale, especially over remote oceanic regions. Each instrument has its own strengths and limitations when it comes to accurately determining the rate of precipitation occurring at the surface. By using the complementary strengths of two satellite based instruments, we attempt to produce a more complete climatology of global oceanic precipitation. The Global Precipitation Measurement (GPM) Core Osbervatory's Dual-frequency Precipitation Radar (DPR) is capable of measuring precipitation producing radar reflectivity above 12 dBZ [Hamada and Takayabu 2016]. The CloudSat satellite's Cloud Profiling Radar (CPR) uses higher frequency C band (94 GHz) radiation, and is therefore capable of measuring precipitation occurring at low precipitation rates which are not detected by the GPM DPR. The precipitation estimates derived by the two satellites are combined and the results are examined. CloudSat data from July 2006 to December 2010 are used. GPM data from March 2014 through May 2016 are used. Since the two datasets do not temporally overlap, this study is conducted from a climatological standpoint. The average occurrence for different precipitation rates is calculated for both satellites. To produce the combined dataset, the precipitation from CloudSat are used for the low precipitation rates while CloudSat precipitation amount is greater than that from GPM DPR, until GPM DPR precipitation amount is higher than that from CloudSat, at which precipitation rate data from the GPM are used. By combining the two datasets, we discuss the seasonal and geo-graphical distribution of weak precipitation detected by CloudSat that is beyond the sensitivity of GPM DPR. We also hope to gain a more complete picture of the precipitation that occurs over oceanic regions.

Effect of synthesis methods on the Ca{sub 3}Co{sub 4}O{sub 9} thermoelectric ceramic performances

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sotelo, A.; Rasekh, Sh.; Torres, M.A.

2015-01-15

Three different synthesis methods producing nanometric grain sizes, coprecipitation with ammonium carbonate, oxalic acid, and by attrition milling have been studied to produce Ca{sub 3}Co{sub 4}O{sub 9} ceramics and compared with the classical solid state route. These three processes have produced high reactive precursors and all the organic material and CaCO{sub 3}·have been decomposed in a single thermal treatment. Coprecipitation leads to pure Ca{sub 3}Co{sub 4}O{sub 9} phase, while attrition milling and classical solid state produce small amounts of Ca{sub 3}Co{sub 2}O{sub 6} secondary phase. Power factor values are similar for all three samples, being slightly lower for the onesmore » produced by attrition milling. These values are much higher than the obtained in samples prepared by the classical solid state method, used as reference. The maximum power factor values determined at 800 °C (∼0.43 mW/K{sup 2} m) are slightly higher than the best reported values obtained in textured ones which also show much higher density values. - Graphical abstract: Impressive raise of PF in Ca{sub 3}Co{sub 4}O{sub 9} thermoelectric materials obtained from nanometric grains. - Highlights: • Ca{sub 3}Co{sub 4}O{sub 9} has been produced by four different methods. • Precursors particle sizes influences on the final performances. • Coprecipitation methods produce single Ca{sub 3}Co{sub 4}O{sub 9} phase. • Power factor reaches values comparable to high density textured materials.« less

Effects of Biochar Amendment on Soil Properties and Soil Carbon Sequestration

NASA Astrophysics Data System (ADS)

Zhang, R.; Zhu, S.

2015-12-01

Biochar addition to soils potentially affects various soil properties and soil carbon sequestration, and these effects are dependent on biochars derived from different feedstock materials and pyrolysis processes. The objective of this study was to investigate the effects of amendment of different biochars on soil physical and biological properties as well as soil carbon sequestration. Biochars were produced with dairy manure and woodchip at temperatures of 300, 500, and 700°C, respectively. Each biochar was mixed at 5% (w/w) with a forest soil and the mixture was incubated for 180 days, during which soil physical and biological properties, and soil respiration rates were measured. Results showed that the biochar addition significantly enhanced the formation of soil macroaggregates at the early incubation time. The biochar application significantly reduced soil bulk density, increased the amount of soil organic matter, and stimulated microbial activity and soil respiration rates at the early incubation stage. Biochar applications improved water retention capacity, with stronger effects by biochars produced at higher pyrolysis temperatures. At the same suction, the soil with woodchip biochars possessed higher water content than with the dairy manure biochars. Biochar addition significantly affected the soil physical and biological properties, which resulted in different soil carbon mineralization rates and the amount of soil carbon storage.

Sex Differences in the Response to Viral Infections: TLR8 and TLR9 Ligand Stimulation Induce Higher IL10 Production in Males

PubMed Central

Torcia, Maria Gabriella; Nencioni, Lucia; Clemente, Ann Maria; Civitelli, Livia; Celestino, Ignacio; Limongi, Dolores; Fadigati, Giulia; Perissi, Eloisa; Cozzolino, Federico; Garaci, Enrico; Palamara, Anna Teresa

2012-01-01

Background Susceptibility to viral infections as well as their severity are higher in men than in women. Heightened antiviral responses typical of women are effective for rapid virus clearance, but if excessively high or prolonged, can result in chronic/inflammatory pathologies. We investigated whether this variability could be in part attributable to differences in the response to the Toll-Like Receptors (TLR) more involved in the virus recognition. Methods Cytokine production by peripheral blood mononuclear cells (PBMCs) from male and female healthy donors after stimulation with Toll-like receptors (TLR) 3, 7, 8, 9 ligands or with viruses (influenza and Herpes-simplex-1) was evaluated. Results Compared to females, PBMCs from males produced not only lower amounts of IFN-α in response to TLR7 ligands but also higher amounts of the immunosuppressive cytokine IL10 after stimulation with TLR8 and TLR9 ligands or viruses. IL10 production after TLR9 ligands or HSV-1 stimulation was significantly related with plasma levels of sex hormones in both groups, whereas no correlation was found in cytokines produced following TLR7 and TLR8 stimulation. Conclusions Given the role of an early production of IL10 by cells of innate immunity in modulating innate and adaptive immune response to viruses, we suggest that sex-related difference in its production following viral nucleic acid stimulation of TLRs may be involved in the sex-related variability in response to viral infections. PMID:22768144

Cloning strategies for heterologous expression of the bacteriocin enterocin A by Lactobacillus sakei Lb790, Lb. plantarum NC8 and Lb. casei CECT475.

PubMed

Jiménez, Juan J; Diep, Dzung B; Borrero, Juan; Gútiez, Loreto; Arbulu, Sara; Nes, Ingolf F; Herranz, Carmen; Cintas, Luis M; Hernández, Pablo E

2015-10-15

Bacteriocins produced by lactic acid bacteria (LAB) attract considerable interest as natural and nontoxic food preservatives and as therapeutics whereas the bacteriocin-producing LAB are considered potential probiotics for food, human and veterinary applications, and in the animal production field. Within LAB the lactobacilli are increasingly used as starter cultures for food preservation and as probiotics. The lactobacilli are also natural inhabitants of the gastrointestinal (GI) tract and attractive vectors for delivery of therapeutic peptides and proteins, and for production of bioactive peptides. Research efforts for production of bacteriocins in heterologous hosts should be performed if the use of bacteriocins and the LAB bacteriocin-producers is ever to meet the high expectations deposited in these antimicrobial peptides. The recombinant production and functional expression of bacteriocins by lactobacilli would have an additive effect on their probiotic functionality. The heterologous production of the bacteriocin enterocin A (EntA) was evaluated in different Lactobacillus spp. after fusion of the versatile Sec-dependent signal peptide (SP usp45 ) to mature EntA plus the EntA immunity gene (entA + entiA) (fragment UAI), and their cloning into plasmid vectors that permitted their inducible (pSIP409 and pSIP411) or constitutive (pMG36c) production. The amount, antimicrobial activity (AA) and specific antimicrobial activity (SAA) of the EntA produced by Lactobacillus sakei Lb790, Lb. plantarum NC8 and Lb. casei CECT475 transformed with the recombinant plasmids pSIP409UAI, pSIP411UAI and pMGUAI varied depending of the expression vector and the host strain. The Lb. casei CECT475 recombinant strains produced the largest amounts of EntA, with the highest AA and SAA. Supernatants from Lb. casei CECT (pSIP411UAI) showed a 4.9-fold higher production of EntA with a 22.8-fold higher AA and 4.7-fold higher SAA than those from Enterococcus faecium T136, the natural producer of EntA. Moreover, supernatants from Lb. casei CECT475 (pSIP411UAI) showed a 15.7- to 59.2-fold higher AA against Listeria spp. than those from E. faecium T136. Lb. casei CECT457 (pSIP411UAI) may be considered a promising recombinant host and cell factory for the production and functional expression of the antilisterial bacteriocin EntA.

Seed sprout production: Consumables and a foundation for higher plant growth in space

NASA Technical Reports Server (NTRS)

Day, Michelle; Thomas, Terri; Johnson, Steve; Luttges, Marvin

1990-01-01

Seed sprouts can be produced as a source of fresh vegetable materials and as higher plant seedlings in space. Sprout production was undertaken to evaluate the mass accumulations possible, the technologies needed, and the reliability of the overall process. Baseline experiments corroborated the utility of sprout production protocols for a variety of seed types. The automated delivery of saturated humidity effectively supplants labor intensive manual soaking techniques. Automated humidification also lend itself to modest centrifugal sprout growth environments. A small amount of ultraviolet radiation effectively suppressed bacterial and fungal contamination, and the sprouts were suitable for consumption.

Altered lignin biosynthesis improves cellulosic bioethanol production in transgenic maize plants down-regulated for cinnamyl alcohol dehydrogenase.

PubMed

Fornalé, Silvia; Capellades, Montserrat; Encina, Antonio; Wang, Kan; Irar, Sami; Lapierre, Catherine; Ruel, Katia; Joseleau, Jean-Paul; Berenguer, Jordi; Puigdomènech, Pere; Rigau, Joan; Caparrós-Ruiz, David

2012-07-01

Cinnamyl alcohol dehydrogenase (CAD) is a key enzyme involved in the last step of monolignol biosynthesis. The effect of CAD down-regulation on lignin production was investigated through a transgenic approach in maize. Transgenic CAD-RNAi plants show a different degree of enzymatic reduction depending on the analyzed tissue and show alterations in cell wall composition. Cell walls of CAD-RNAi stems contain a lignin polymer with a slight reduction in the S-to-G ratio without affecting the total lignin content. In addition, these cell walls accumulate higher levels of cellulose and arabinoxylans. In contrast, cell walls of CAD-RNAi midribs present a reduction in the total lignin content and of cell wall polysaccharides. In vitro degradability assays showed that, although to a different extent, the changes induced by the repression of CAD activity produced midribs and stems more degradable than wild-type plants. CAD-RNAi plants grown in the field presented a wild-type phenotype and produced higher amounts of dry biomass. Cellulosic bioethanol assays revealed that CAD-RNAi biomass produced higher levels of ethanol compared to wild-type, making CAD a good target to improve both the nutritional and energetic values of maize lignocellulosic biomass.

Rheological characterization of cataplasm bases composed of cross-linked partially neutralized polyacrylate hydrogel.

PubMed

Wang, Jian; Zhang, Hongqin; An, Dianyun; Yu, Jian; Li, Wei; Shen, Teng; Wang, Jianxin

2014-10-01

Viscoelasticity is a useful parameter for characterizing the intrinsic properties of the cross-linked polyacrylate hydrogel used in cataplasm bases. The aim of this study was to investigate the effects of various formulation parameters on the rheological characteristics of polyacrylate hydrogel. The hydrogel layers were formed using a partially neutralized polyacrylate (Viscomate(™)), which contained acrylic acid and sodium acrylate in different copolymerization ratios, as the cross-linked gel framework. Dihydroxyaluminum aminoacetate (DAAA), which produces aluminum ions, was used as the cross-linking agent. Rheological analyses were performed using a "stress amplitude sweep" and a "frequency sweep". The results showed that greater amounts of acrylic acid in the structure of Viscomate as well as higher concentrations of DAAA and Viscomate led to an increase in the elastic modulus (G'). However, greater amounts of acrylic acid in the structure of Viscomate and higher concentrations of DAAA had an opposite on the viscous modulus (G″); this might be owing to higher steric hindrance. The results of this study can serve as guidelines for the optimization of formulations for cataplasms.

Functioning efficiency of intermediate coolers of multistage steam-jet ejectors of steam turbines

NASA Astrophysics Data System (ADS)

Aronson, K. E.; Ryabchikov, A. Yu.; Brodov, Yu. M.; Zhelonkin, N. V.; Murmanskii, I. B.

2017-03-01

Designs of various types of intermediate coolers of multistage ejectors are analyzed and thermal effectiveness and gas-dynamic resistance of coolers are estimated. Data on quantity of steam condensed from steam-air mixture in stage I of an ejector cooler was obtained on the basis of experimental results. It is established that the amount of steam condensed in the cooler constitutes 0.6-0.7 and is almost independent of operating steam pressure (and, consequently, of steam flow) and air amount in steam-air mixture. It is suggested to estimate the amount of condensed steam in a cooler of stage I based on comparison of computed and experimental characteristics of stage II. Computation taking this hypothesis for main types of mass produced multistage ejectors into account shows that 0.60-0.85 of steam amount should be condensed in stage I of the cooler. For ejectors with "pipe-in-pipe" type coolers (EPO-3-200) and helical coolers (EO-30), amount of condensed steam may reach 0.93-0.98. Estimation of gas-dynamic resistance of coolers shows that resistance from steam side in coolers with built-in and remote pipe bundle constitutes 100-300 Pa. Gas-dynamic resistance of "pipein- pipe" and helical type coolers is significantly higher (3-6 times) compared with pipe bundle. However, performance by "dry" (atmospheric) air is higher for ejectors with relatively high gas-dynamic resistance of coolers than those with low resistance at approximately equal operating flow values of ejectors.

Availability of lignocellulose from forestry waste for use as a biofuel in China.

PubMed

Xie, Hui; Zhang, Dong; Mao, Guotao; Wang, Fengqin; Song, Andong

2018-05-01

Biomass is a very important renewable energy and plays an important role in the energy structure of China. Here, the role of forestry waste in producing energy in China was analyzed and the availability of forestry waste for biofuel production, theoretically collectable amounts of forest biomass, and density of forestry waste were assessed. Agricultural and forestry waste are important biomass resources. The potential for using forestry waste as a low cost substrate for producing fuel ethanol using existing forestry resources and techniques was analyzed, and the feasibility of producing fuel ethanol in different Chinese provinces was assessed using the specific situation for each province. The results showed that 1081.73 × 10 6  t of forestry waste could be produced in China, and 270.43 × 10 6  t (25% of the amount that could be collected) could be used to produce fuel ethanol. Assuming 10 t of sawdust could be converted into 1 t of ethanol, 27 × 10 6  t of ethanol could be produced from forestry waste. Different provinces have different potentials for producing ethanol from forestry waste, Guangdong Province, Guangxi Province, Sichuan Province, and Yunnan Province having higher potentials than the other provinces. It was predicted that 4478 × 10 6  t of fuel ethanol could be produced from woodcraft waste by 2020, and the provinces with the most potential were found to be Fujian Province, Heilongjiang Province, Jilin Province, Shanxi Province, Sichuan Province, Xinjiang Province, and Yunnan Province. Using forestry waste to produce ethanol could alleviate the energy shortage in China.

Development of eco-friendly bioplastic like PHB by distillery effluent microorganisms.

PubMed

Gangurde, Nilesh S; Sayyed, Riyaz Z; Kiran, Shashi; Gulati, Arvind

2013-01-01

During screening for poly-β-hydroxybutyrate (PHB) producing bacteria from distillery effluent sample, six out of 30 isolates comprising of three strains of Alcaligenes sp., two strains of Bacillus sp., and one strain of Pseudomonas sp. were found to accumulate varying levels of intracellular PHB. Amongst the various isolates, Alcaligenes sp. RZS4 was found as the potent PHB-producing organism, accumulating higher amounts of PHB. PHB productivity was further enhanced in the presence of oxygen, nitrogen-limiting conditions, and cloning of PHB synthesizing genes of Alcaligenes sp. RZS 4 into Escherichia coli. A twofold increase in PHB yield was obtained from recombinant E. coli vis-à-vis Alcaligenes sp.; the recombinant E. coli accumulated more PHB in NDMM, produced good amount of PHB in a single-stage cultivation process under both nutrient-rich and nutrient-deficient conditions. Extraction of PHB with acetone-alcohol (1:1) was found as suitable method for optimum extraction of PHB as this mixture selectively extracted PHB without affecting the non-PHB cell mass. PHB extract from recombinant E. coli showed the presence of C-H, =O stretching, =C-H deformation, =C-H, =CH, and =C-O functional groups characteristic of PHB.

Predicting language outcomes for children learning AAC: Child and environmental factors

PubMed Central

Brady, Nancy C.; Thiemann-Bourque, Kathy; Fleming, Kandace; Matthews, Kris

2014-01-01

Purpose To investigate a model of language development for nonverbal preschool age children learning to communicate with AAC. Method Ninety-three preschool children with intellectual disabilities were assessed at Time 1, and 82 of these children were assessed one year later at Time 2. The outcome variable was the number of different words the children produced (with speech, sign or SGD). Children’s intrinsic predictor for language was modeled as a latent variable consisting of cognitive development, comprehension, play, and nonverbal communication complexity. Adult input at school and home, and amount of AAC instruction were proposed mediators of vocabulary acquisition. Results A confirmatory factor analysis revealed that measures converged as a coherent construct and an SEM model indicated that the intrinsic child predictor construct predicted different words children produced. The amount of input received at home but not at school was a significant mediator. Conclusions Our hypothesized model accurately reflected a latent construct of Intrinsic Symbolic Factor (ISF). Children who evidenced higher initial levels of ISF and more adult input at home produced more words one year later. Findings support the need to assess multiple child variables, and suggest interventions directed to the indicators of ISF and input. PMID:23785187

Effect of carbon and nitrogen sources on simultaneous production of α-amylase and green food packaging polymer by Bacillus sp. CFR 67.

PubMed

Sreekanth, M S; Vijayendra, S V N; Joshi, G J; Shamala, T R

2013-04-01

In this paper, effect of different carbon and nitrogen sources, including hydrolysates of rice bran and wheat bran, on simultaneous production of α-amylase (for hydrolysis of starch in food systems) and polyhydroxyalkanoates (PHA, a green biopolymer, which can be used as a packing material for foods) by Bacillus sp. CFR 67 was studied by submerged fermentation. Amongst various carbon sources tested, glucose and sucrose supported production of significantly (P < 0.05) higher amount of α-amylase (66 U/ml) and PHA (444 mg/l), respectively. Of the nitrogen sources tested, ammonium acetate and beef extract led to the production of maximum amount of amylase (36 U/ml) and PHA (592 mg/l), respectively. Supplementation of the production medium with wheat bran hydrolysate (50 ml/l) produced significantly higher amounts of amylase (73 U/ml) and PHA (524 mg/l). Thus this study indicated the potential of agro-residues for the production of value added biomolecules, which can reduce the cost of production of these molecules and enables to reduce the pollution mainly caused by the use of non biodegradable plastics.

Large numbers of interleukins-22- and -17A-producing T helper cells in cholangiocarcinoma related to liver fluke infection.

PubMed

Su, Si-Biao; Zhang, Jian-Feng; Huang, Fei-Fei; Cen, Yu; Jiang, Hai-Xing

2017-08-01

Cholangiocarcinoma (CCA) associated with liver fluke infection involves inflammatory and immune processes; however, whether these involve the proinflammatory cytokine IL-17A and proliferative cytokine IL-22 remains unclear. Here, numbers of IL-22- and IL-17A-producing Th cells and cytokine concentrations in 30 patients with CCA and long-term liver fluke infection, 40 patients with liver-fluke infection but not CCA, and 16 healthy controls were compared. Analyses were performed using immunohistochemistry, flow cytometry, ELISA and RT-PCR. Immunohistochemical staining showed weaker expression of IL-22 and IL-17A in patients with CCA with than in those without liver fluke infection (P < 0.01). Flow cytometry revealed significantly greater median proportions of IL-22-producing T helper cells in patients with CCA (2.2%) than in those without it (0.69%) or controls (0.4%, P < 0.001). Similar results were obtained for IL-17A-producing T helper cells. ELISA revealed plasma concentrations of IL-22 were 1.3-fold higher in patients with CCA than in those without it and 4.6-fold higher than in controls (P < 0.001). Plasma concentrations of IL-17A were 2.5-fold higher in patients with CCA than in those without it, and 21-fold higher than in controls (P < 0.001). Amounts of IL-22 and IL-17A mRNAs in blood were significantly higher in patients with CCA than in the other two groups. Proportions of CD4 + CD45RO + T cells producing IL-22 correlated with proportions producing IL-17A (r = 0.759; P < 0.001), and plasma concentrations of IL-22 correlated with those of IL-17A (r = 0.726; P < 0.001). These results suggest that both IL-17A and IL-22 affect development of CCA related to liver fluke infection. © 2017 The Societies and John Wiley & Sons Australia, Ltd.

Nitrogen removal from wastewater by a catalytic oxidation method.

PubMed

Huang, T L; Macinnes, J M; Cliffe, K R

2001-06-01

The ammonia-containing waste produced in industries is usually characterized by high concentration and high temperature, and is not treatable by biological methods directly. In this study, a hydrophobic Pt/SDB catalyst was first used in a trickle-bed reactor to remove ammonia from wastewater. In the reactor, both stripping and catalytic oxidation occur simultaneously. It was found that higher temperature and higher oxygen partial pressure enhanced the ammonia removal. A reaction pathway, which involves oxidizing ammonia to nitric oxide, which then further reacts with ammonia to produce nitrogen and water, was confirmed. Small amounts of by-products, nitrites and nitrates were also detected in the resultant reaction solution. These compounds came from the absorption of nitrogen oxides. Both the minimum NO2- selectivity and maximum ammonia removal were achieved when the resultant pH of treated water was near 7.5 for a feed of unbuffered ammonia solution.

Consolidation of silicon nitride without additives

NASA Technical Reports Server (NTRS)

Sikora, P. F.; Yeh, H. C.

1977-01-01

The feasibility of producing a sound, dense Si3N4 body without additives was explored, using conventional gas hot isostatic pressing techniques and an uncommon hydraulic hot isostatic pressing technique. These two techniques produce much higher pressure 275-413 MN/m sq (40,000 - 60,000 psi) than hot-pressing techniques. Evaluation was based on density measurement, microscopic examination, both optical and electron, and X-ray diffraction analysis. The results are summarized as follows: (1) Si3N4 can be densified to high density, greater than 95% of theoretical, without additions. (2) The higher density Si3N4 specimens appear to be associated with a greater amount of alpha to beta transformation. (3) Under high pressure, the alpha to beta transformation can occur at a temperature as low as 1150 C. (4) Grain deformation and subsequent recrystallization and grain refinement result from hot isostatic pressing of Si3N4.

Metal accumulation potential of wild plants in tannery effluent contaminated soil of Kasur, Pakistan: field trials for toxic metal cleanup using Suaeda fruticosa.

PubMed

Firdaus-e Bareen; Tahira, Syeda Anjum

2011-02-15

The tannery effluent contaminated lands, adjacent to Depalpur Road, Kasur, Pakistan, have been rendered infertile due to long term effluent logging from the leather industry. The area has been colonized by twelve plant species among which Suaeda fruticosa, Salvadora oleoides and Calatropis procera have been found to be the most common and high biomass producing plants. S. fruticosa was subjected to further experimentation because of its high biomass and phytoextraction capabilities for metals. The pot and field experiments were carried out simultaneously. Pot experiments were conducted using the same field soil in column pots with stoppard bottoms to obtain the leachate. EDTA treatment caused a greater solubility of Cr in the soil pore water. In higher doses more amount of the heavy metal was leached. The increase in the amount of EDTA significantly caused a decrease in the biomass of plants without toxicity symptoms. A higher biomass of plants was observed in the field as compared to the pot experiment. The greatest amount of Na was accumulated by leaves of S. fruticosa followed by stem and roots. Similarly, the greatest amount of Cr was bioaccumulated by leaves of S. fruticosa, but followed by roots and then stem. S. fruticosa can be employed in rehabilitation of tannery effluent contaminated soil using small doses of EDTA. Copyright © 2010 Elsevier B.V. All rights reserved.

Drugs in breast milk.

PubMed

Hervada, A R; Feit, E; Sagraves, R

1978-09-01

The amount of drug excreted into breast milk is dependent upon the lipid solubility of the medication, the mechanism of transport, the degree of ionization, and change in plasma pH. The higher the lipid solubility, the greater the concentration in human milk. The majority of drugs are transported into mammary blood capillaries by passive diffusion. The rest are transported by reverse pinocytosis. Once the drug has entered the epithelial cells of breast tissue, the drug molecules are excreted into the human milk by active transport, passive diffusion, or apocrine secretion. The amount of free (active) drug available for transport depends on the degree of protein binding the plasma pH. Another factor affecting excretion of drugs is the time when breast feeding occurs. In the 1st few days of life, when colostrum is present, water-soluble drugs pass through the breast more easily than afterwards when milk is produced. Then lipid-soluble drugs cross in higher concentrations. The effect on nursing infants is dependent on the amount excreted into the milk, the total amount absorbed by the infant, and the toxicity of the drug. The use of the following drugs in breast feeding mothers is reviewed: anticoagulants, antihypertensives and diuretics, antimicrobials, drugs affecting the central nervous system (alcohol, chloral hydrate, meprobamate, lithium, and aspirin), marijuana, other drugs (antihistamines, atropine, ergot alkaloids, laxatives, nicotine, iodides, propylthiouracil, theophylline), hormones (insulin, thyroxine, and oral contraceptives), and radiopharmaceuticals.

Physiological ecology of Clostridium glycolicum RD-1, an aerotolerant acetogen isolated from sea grass roots.

PubMed

Küsel, K; Karnholz, A; Trinkwalter, T; Devereux, R; Acker, G; Drake, H L

2001-10-01

An anaerobic, H(2)-utilizing bacterium, strain RD-1, was isolated from the highest growth-positive dilution series of a root homogenate prepared from the sea grass Halodule wrightii. Cells of RD-1 were gram-positive, spore-forming, motile rods that were linked by connecting filaments. Acetate was produced in stoichiometries indicative of an acetyl coenzyme A (acetyl-CoA) pathway-dependent metabolism when RD-1 utilized H(2)-CO(2), formate, lactate, or pyruvate. Growth on sugars or ethylene glycol yielded acetate and ethanol as end products. RD-1 grew at the expense of glucose in the presence of low initial concentrations (up to 6% [vol/vol]) of O(2) in the headspace of static, horizontally incubated culture tubes; the concentration of O(2) decreased during growth in such cultures. Peroxidase, NADH oxidase, and superoxide dismutase activities were detected in the cytoplasmic fraction of cells grown in the presence of O(2). In comparison to cultures incubated under strictly anoxic conditions, acetate production decreased, higher amounts of ethanol were produced, and lactate and H(2) became significant end products when RD-1 was grown on glucose in the presence of O(2). Similarly, when RD-1 was grown on fructose in the presence of elevated salt concentrations, lower amounts of acetate and higher amounts of ethanol and H(2) were produced. When the concentration of O(2) in the headspace exceeded 1% (vol/vol), supplemental H(2) was not utilized. The 16S rRNA gene of RD-1 had a 99.7% sequence similarity to that of Clostridium glycolicum DSM 1288(T), an organism characterized as a fermentative anaerobe. Comparative experiments with C. glycolicum DSM 1288(T) demonstrated that it had negligible H(2)- and formate-utilizing capacities. However, carbon monoxide dehydrogenase was detected in both RD-1 and C. glycolicum DSM 1288(T). A 91.4% DNA-DNA hybridization between the genomic DNA of RD-1 and that of C. glycolicum DSM 1288(T) confirmed that RD-1 was a strain of C. glycolicum. These results indicate that (i) RD-1 metabolizes certain substrates via the acetyl-CoA pathway, (ii) RD-1 can tolerate and consume limited amounts of O(2), (iii) oxic conditions favor the production of ethanol, lactate, and H(2) by RD-1, and (iv) the ability of RD-1 to cope with limited amounts of O(2) might contribute to its survival in a habitat subject to daily gradients of photosynthesis-derived O(2).

Distribution and stability of aflatoxin M1 during processing, ripening and storage of Telemes cheese.

PubMed

Govaris, A; Roussi, V; Koidis, P A; Botsoglou, N A

2001-05-01

Telemes cheeses were produced using milk that was artificially-contaminated with aflatoxin M1 at the levels of 0.050 and 0.100 microg/l. The cheeses produced in the two cheese-making trials were allowed to ripen for 2 months and stored for an additional 4 months to simulate commercial production of Telemes cheese. Concentrations of aflatoxin M1 in whey, curd, brine, and the produced cheeses were determined at intervals by liquid chromatography and fluorometric detection coupled with immunoaffinity column extraction. Concentrations of aflatoxin M1 in the produced curds were found to be 3.9 and 4.4 times higher than those in milk, whereas concentrations in whey were lower than those in curd and milk. Aflatoxin M1 was present in cheese at higher concentrations at the beginning than at the end of the ripening/storage period, and it declined to concentrations 2.7 and 3.4 times higher than those initially present in milk by the end of the sixth month of storage. Concentrations of aflatoxin M1 in brine started low and increased by the end of the ripening/storage period but only a portion of the amounts of aflatoxin M1 lost from cheese was found in the brine. Results showed that Telemes cheeses produced from milk containing aflatoxin M1 at a concentration close to either the maximum acceptable level of 0.05 microg/l set by the European union (EU) or at double this value, will contain the toxin at a level that is much lower or slightly higher, respectively, than the maximum acceptable level of 0.250 microg of aflatoxin M1/kg cheese set by some countries.

Preparation of interesterified plastic fats from fats and oils free of trans fatty acid.

PubMed

Lee, Jeung Hee; Akoh, Casimir C; Himmelsbach, David S; Lee, Ki-Teak

2008-06-11

Interesterified plastic fats were produced with trans-free substrates of fully hydrogenated soybean oil, extra virgin olive oil, and palm stearin in a weight ratio of 10:20:70, 10:40:50, and 10:50:40, respectively, by lipase catalysis. The major fatty acids of the products were palmitic (32.2-47.4%), stearic (12.0-12.4%), and oleic acid (33.6-49.5%). After storage at 5 degrees C (refrigerator temperature) or 24 degrees C (room temperature) for 16 h, the physical properties were evaluated for solid fat content, texture, melting, and crystallization behavior, viscoelastic properties, crystal polymorphism, and crystal microstructure. The interesterified fats contained desirable crystal polymorphs (beta' form) as determined by X-ray diffraction spectroscopy. They exhibited a wide plastic range of solid fat content of 52-58% at 10 degrees C and 15% at 40 degrees C. The physical properties were influenced by the ratio of palm stearin and olive oil. Harder and more brittle texture, crystallization and melting at higher temperature, higher solid fat contents, and more elastic (G') or viscous (G') characteristics were observed in the produced fats containing a higher content of palm stearin and lower content of olive oil. The produced fats stored at 5 degrees C consisted mostly of beta' form crystal together with a small content of beta form, while those at 24 degrees C had only beta' form. The produced fat with a higher amount of palm stearin appeared to have more beta' form crystal and small size crystal clusters. Thus, the physical properties of the produced plastic fats may be desirable for use in a bakery product.

Occurrence and estimation of trans-resveratrol in one-year-old canes from seven major Chinese grape producing regions.

PubMed

Zhang, Ang; Fang, Yulin; Li, Xuan; Meng, Jiangfei; Wang, Hua; Li, Hua; Zhang, Zhenwen; Guo, Zhijun

2011-03-31

The concentration of trans-resveratrol in 165 grape cane samples from three major grape production regions and four large distribution centers of Chinese wild Vitis species were determined by reversed-phase high-performance liquid chromatography (HPLC). Among the different genotype groups and purpose of uses, cultivars of V. vinifera had much higher amounts of trans-resveratrol than did the cultivars of both V. labrusca or V. labrusca and V. vinifera hybrids, and within the V. vinifera species, significantly higher amounts of trans-resveratrol were found in wine grapes compared to table ones. No significant differences were observed between V. labrusca and its hybrids from crosses with V. vinifera, and between red cultivars and white ones (P < 0.05 or P < 0.01). The contents of trans-resveratrol, as a normal constituent occurring in grape canes, in Chinese wild species of V. amurensis, V. pentagona, and V. davidii from their native habitats were also relatively high.

Generation of reactive oxygen species and oxidative stress in Escherichia coli and Staphylococcus aureus by a novel semiconductor catalyst

NASA Astrophysics Data System (ADS)

Chow, K. L.; Mak, N. K.; Wong, M. H.; Zhou, X. F.; Liang, Y.

2011-03-01

The objective of this study was to investigate antimicrobial mechanisms of a new catalytic material (charge transfer auto oxidation-reduction type catalyst, CT catalyst) that may have great potential for application in water/wastewater treatment. Generation of reactive oxygen species (ROS) in bacteria-free solution, induction of ROS and oxidative damage in bacteria (including E. coli and S. aureus) were examined for the CT catalyst. The results showed that significantly higher ( p < 0.05, via t-test) amount of hydroxyl radicals was generated by the CT catalyst compared with the control, particularly after 6 h of contact time that more than twice of the amount of the control was produced. The generation of ROS in the bacteria was greater under higher pH and temperature levels, which closely related with the oxidative damage in cells. The results indicated that CT catalyst induced oxidative damage in the bacteria might serve as an important mechanism interpreting the anti-microbial function of the CT catalyst.

Sulfur in serpentinized oceanic peridotites: Serpentinization processes and microbial sulfate reduction

USGS Publications Warehouse

Alt, J.C.; Shanks, Wayne C.

1998-01-01

The mineralogy, contents, and isotopic compositions of sulfur in oceanic serpentinites reflect variations in temperatures and fluid fluxes. Serpentinization of <1 Ma peridotites at Hess Deep occurred at high temperatures (200??-400??C) and low water/rock ratios. Oxidation of ferrous iron to magnetite maintained low fO2and produced a reduced, low-sulfur assemblage including NiFe alloy. Small amounts of sulfate reduction by thermophilic microbes occurred as the system cooled, producing low-??34S sulfide (1.5??? to -23.7???). In contrast, serpentinization of Iberian Margin peridotites occurred at low temperatures (???20??-200??C) and high water/rock ratios. Complete serpentinization and consumption of ferrous iron allowed evolution to higher fO2. Microbial reduction of seawater sulfate resulted in addition of low-??34S sulfide (-15 to -43???) and formation of higher-sulfur assemblages that include valleriite and pyrite. The high SO4/total S ratio of Hess Deep serpentinites (0.89) results in an increase of total sulfur and high ??34S of total sulfur (mean ??? 8???). In contrast, Iberian Margin serpentinites gained large amounts of 34S-poor sulfide (mean total S = 3800 ppm), and the high sulfide/total S ratio (0.61) results in a net decrease in ??34S of total sulfur (mean ??? -5???). Thus serpentinization is a net sink for seawater sulfur, but the amount fixed and its isotopic composition vary significantly. Serpentinization may result in uptake of 0.4-14 ?? 1012 g S yr-1 from the oceans, comparable to isotopic exchange in mafic rocks of seafloor hydrothermal systems and approaching global fluxes of riverine sulfate input and sedimentary sulfide output.

Extracellular Vesicles Released from Mycobacterium tuberculosis-Infected Neutrophils Promote Macrophage Autophagy and Decrease Intracellular Mycobacterial Survival

PubMed Central

Alvarez-Jiménez, Violeta D.; Leyva-Paredes, Kahiry; García-Martínez, Mariano; Vázquez-Flores, Luis; García-Paredes, Víctor Gabriel; Campillo-Navarro, Marcia; Romo-Cruz, Israel; Rosales-García, Víctor Hugo; Castañeda-Casimiro, Jessica; González-Pozos, Sirenia; Hernández, José Manuel; Wong-Baeza, Carlos; García-Pérez, Blanca Estela; Ortiz-Navarrete, Vianney; Estrada-Parra, Sergio; Serafín-López, Jeanet; Wong-Baeza, Isabel; Chacón-Salinas, Rommel; Estrada-García, Iris

2018-01-01

Tuberculosis is an infectious disease caused by Mycobacterium tuberculosis (Mtb). In the lungs, macrophages and neutrophils are the first immune cells that have contact with the infecting mycobacteria. Neutrophils are phagocytic cells that kill microorganisms through several mechanisms, which include the lytic enzymes and antimicrobial peptides that are found in their lysosomes, and the production of reactive oxygen species. Neutrophils also release extracellular vesicles (EVs) (100–1,000 nm in diameter) to the extracellular milieu; these EVs consist of a lipid bilayer surrounding a hydrophilic core and participate in intercellular communication. We previously demonstrated that human neutrophils infected in vitro with Mtb H37Rv release EVs (EV-TB), but the effect of these EVs on other cells relevant for the control of Mtb infection, such as macrophages, has not been completely analyzed. In this study, we characterized the EVs produced by non-stimulated human neutrophils (EV-NS), and the EVs produced by neutrophils stimulated with an activator (PMA), a peptide derived from bacterial proteins (fMLF) or Mtb, and observed that the four EVs differed in their size. Ligands for toll-like receptor (TLR) 2/6 were detected in EV-TB, and these EVs favored a modest increase in the expression of the co-stimulatory molecules CD80, a higher expression of CD86, and the production of higher amounts of TNF-α and IL-6, and of lower amounts of TGF-β, in autologous human macrophages, compared with the other EVs. EV-TB reduced the amount of intracellular Mtb in macrophages, and increased superoxide anion production in these cells. TLR2/6 ligation and superoxide anion production are known inducers of autophagy; accordingly, we found that EV-TB induced higher expression of the autophagy-related marker LC3-II in macrophages, and the co-localization of LC3-II with Mtb inside infected macrophages. The intracellular mycobacterial load increased when autophagy was inhibited with wortmannin in these cells. In conclusion, our results demonstrate that neutrophils produce different EVs in response to diverse activators, and that EV-TB activate macrophages and promote the clearance of intracellular Mtb through early superoxide anion production and autophagy induction, which is a novel role for neutrophil-derived EVs in the immune response to Mtb. PMID:29520273

Extracellular Vesicles Released from Mycobacterium tuberculosis-Infected Neutrophils Promote Macrophage Autophagy and Decrease Intracellular Mycobacterial Survival.

PubMed

Alvarez-Jiménez, Violeta D; Leyva-Paredes, Kahiry; García-Martínez, Mariano; Vázquez-Flores, Luis; García-Paredes, Víctor Gabriel; Campillo-Navarro, Marcia; Romo-Cruz, Israel; Rosales-García, Víctor Hugo; Castañeda-Casimiro, Jessica; González-Pozos, Sirenia; Hernández, José Manuel; Wong-Baeza, Carlos; García-Pérez, Blanca Estela; Ortiz-Navarrete, Vianney; Estrada-Parra, Sergio; Serafín-López, Jeanet; Wong-Baeza, Isabel; Chacón-Salinas, Rommel; Estrada-García, Iris

2018-01-01

Tuberculosis is an infectious disease caused by Mycobacterium tuberculosis (Mtb). In the lungs, macrophages and neutrophils are the first immune cells that have contact with the infecting mycobacteria. Neutrophils are phagocytic cells that kill microorganisms through several mechanisms, which include the lytic enzymes and antimicrobial peptides that are found in their lysosomes, and the production of reactive oxygen species. Neutrophils also release extracellular vesicles (EVs) (100-1,000 nm in diameter) to the extracellular milieu; these EVs consist of a lipid bilayer surrounding a hydrophilic core and participate in intercellular communication. We previously demonstrated that human neutrophils infected in vitro with Mtb H37Rv release EVs (EV-TB), but the effect of these EVs on other cells relevant for the control of Mtb infection, such as macrophages, has not been completely analyzed. In this study, we characterized the EVs produced by non-stimulated human neutrophils (EV-NS), and the EVs produced by neutrophils stimulated with an activator (PMA), a peptide derived from bacterial proteins (fMLF) or Mtb, and observed that the four EVs differed in their size. Ligands for toll-like receptor (TLR) 2/6 were detected in EV-TB, and these EVs favored a modest increase in the expression of the co-stimulatory molecules CD80, a higher expression of CD86, and the production of higher amounts of TNF-α and IL-6, and of lower amounts of TGF-β, in autologous human macrophages, compared with the other EVs. EV-TB reduced the amount of intracellular Mtb in macrophages, and increased superoxide anion production in these cells. TLR2/6 ligation and superoxide anion production are known inducers of autophagy; accordingly, we found that EV-TB induced higher expression of the autophagy-related marker LC3-II in macrophages, and the co-localization of LC3-II with Mtb inside infected macrophages. The intracellular mycobacterial load increased when autophagy was inhibited with wortmannin in these cells. In conclusion, our results demonstrate that neutrophils produce different EVs in response to diverse activators, and that EV-TB activate macrophages and promote the clearance of intracellular Mtb through early superoxide anion production and autophagy induction, which is a novel role for neutrophil-derived EVs in the immune response to Mtb.

Coal-fired power generaion, new air quality regulations, and future U.S. coal production

USGS Publications Warehouse

Attanasi, E.D.; Root, D.H.

1999-01-01

Tighter new regulation of stack gas emissions and competition in power generation are driving electrical utilities to demand cleaner, lower sulfur coal. Historical data on sulfur content of produced coals shows little variability in coal quality for individual mines and individual coal-producing counties over relatively long periods of time. If coal-using power generators follow the compliance patterns established in Phase I of the 1990 Clean Air Act Amendments, then the industry's response to the tighter Phase II emissions standards will result in large amounts of coal production shifting from higher sulfur areas to areas with lower cost low sulfur coal. One reason this shift will likely occur is that currently only 30% of U.S. coal-fired electrical generating capacity is equipped with flue-gas scrubbers. In 1995, coal mines in the higher sulfur areas of the Illinois Basin and Northern and Central Appalachia employed 78% of all coal miners (>70,000 miners). A substantial geographical redistribution of the nation's coal supplies will likely lead to economic dislocations that will reach beyond local coal-producing areas.

Liquid fuel generation from algal biomass via a two-step process: effect of feedstocks.

PubMed

Xu, Yu-Ping; Duan, Pei-Gao; Wang, Feng; Guan, Qing-Qing

2018-01-01

In this study, a two-step processing method (hydrothermal liquefaction followed by catalytic upgrading) was used to produce upgraded bio-oil. A comprehensive screening analysis of algal species, including four microalgae and four macroalgae, was conducted to bridge the gap between previous accounts of microalgae and macroalgae hydrothermal liquefaction and the upgrading process of the resulting crude bio-oils. Hydrothermal liquefaction using eight algal biomasses was performed at 350 °C for 1 h. The microalgae always produced a higher crude bio-oil yield than the macroalgae due to their high lipid content, among which Schizochytrium limacinum provided the maximum crude bio-oil yield of 54.42 wt%. For microalgae, higher amounts of N in the biomass resulted in higher amounts of N in the crude bio-oil; however, contrary results were observed for the macroalgae. The crude bio-oils generated from both the microalgae and macroalgae were characterized as having a high viscosity, total acid number, and heteroatom content, and they were influenced by the biochemical compositions of the feedstocks. Next, all eight-crude bio-oils were treated at 400 °C for 2 h with 10 wt% Ru/C using tetralin as the hydrogen donor. The hydrogen source was provided after tetralin was transformed to naphthalene. All the upgraded bio-oils had higher energy densities and significantly lower N, O, and S contents and viscosities than their corresponding crude bio-oils. However, the H/C molar ratio of the upgraded bio-oils decreased due to the absence of external hydrogen relative to the crude bio-oils. The S content of the upgraded bio-oil produced from upgrading the Schizochytrium limacinum crude bio-oil was even close to the 50 ppm requirement of China IV diesel. Microalgae are better feedstocks than macroalgae for liquid fuel production. Biochemical components have a significant impact on the yield and composition of crude bio-oil. Tetralin does not perform as well as external hydrogen for controlling coke formation. The S content of the upgraded bio-oil can be reduced to 76 ppm for the crude bio-oil produced from Schizochytrium limacinum . Upgraded bio-oils have similar properties to those of naphtha and jet fuel.

Screening and production of ligninolytic enzyme by a marine-derived fungal Pestalotiopsis sp. J63.

PubMed

Chen, Hui-Ying; Xue, Dong-Sheng; Feng, Xiao-Yu; Yao, Shan-Jing

2011-12-01

Marine-derived fungi are prone to produce structurally unique secondary metabolites, a considerable number of which display the promising biological properties and/or industrial applications. Among those, ligninolytic enzymes have attracted great interest in recent years. In this work, about 20 strains were isolated from sea mud samples collected in the East China Sea and then screened for their capacity to produce lignin-degrading enzymes. The results showed that a strain, named J63, had a great potential to secrete a considerable amount of laccase. Using molecular method, it was identified as an endophytic fungus, Pestalotiopsis sp. which was rarely reported as ligninolytic enzyme producer in the literature. The production of laccase by Pestalotiopsis sp. J63 was investigated under submerged fermentation (SF) and solid state fermentation (SSF) with various lignocellulosic by-products as substrates. The SSF of rice straw powder accumulated the highest level of laccase activity (10,700 IU/g substrate), whereas the SF of untreated sugarcane bagasse provided the maximum amount of laccase activity (2,000 IU/ml). The value was far higher than those reported by other reports. In addition, it produced 0.11 U/ml cellulase when alkaline-pretreated sugarcane bagasse was used as growth substrate under SF. Meanwhile, the growth of fungi and laccase production under different salinity conditions were also studied. It appeared to be a moderately halo-tolerant organism.

Inter-serotype comparison of polysaccharides produced by extracellular enzymes from Streptococcus mutans.

PubMed

Yakushiji, T; Inoue, M; Koga, T

1984-04-15

The biochemical and morphological characteristics of polysaccharides synthesized from sucrose by extracellular enzymes from D-glucose-grown Streptococcus mutans representing serotypes a-g were compared. The polysaccharides synthesized by the enzymes from serotypes a, d, and g formed visible aggregates and firmly adhered to glass surfaces, whereas those formed by the enzymes from serotypes b, c, e, and f floated homogeneously and were poorly adherent. The enzymes of serotypes a, d, and g produced large amounts of water-insoluble polysaccharides (IPs, D-glucans), and those of serotypes b, c, e, and f water-soluble polysaccharides (SPs, D-glucans and D- fructans ). As compared with the IPs of serotypes b, c, e, and f, the IPs of serotypes a, d, and g (a) contained a higher proportion of (1----3)-alpha-D-glucosidic linkages and alpha-D-(1----3,6) branch linkages; (b) showed higher susceptibility to (1----3)-alpha-D-glucanase (serotype a excepted) and lower (1----6)-alpha-D-glucanase sensitivity; (c) contained larger amounts of high-molecular-weight fractions; (d) showed higher intrinsic viscosities (serotype b excepted); and (e) had lower S. mutans cell-agglutination activities. On electron-microscope observation, the IPs of all serotypes showed two fibrillar components; a double-stranded fibril, with short, fluffy protrusions extending out of its periphery, and a fine, single-stranded fibril. Thus, the serotypes could be divided into two major groups: a, d, and g; and b, c, e, and f. No similar grouping of serotypes was indicated by the chemical and morphological properties of SPs.

Glyphosate and AMPA contents in sediments produced by wind erosion of agricultural soils in Argentina

NASA Astrophysics Data System (ADS)

Aparicio, Virginia; Aimar, Silvia; De Gerónimo, Eduardo; Buschiazzo, Daniel; Mendez, Mariano; Costa, José Luis

2014-05-01

Wind erosion of soils is an important event in arid and semiarid regions of Argentina. The magnitude of wind erosion occurring under different management practices is relatively well known in this region but less information is available on the quality of the eroded material. Considering that the intensification of agriculture may increase the concentrations of substances in the eroded material, producing potential negative effects on the environment, we analyzed the amount of glyphosate and AMPA in sediments produced by wind erosion of agricultural soils of Argentina. Wind eroded materials were collected by means of BSNE samplers in two loess sites of the semiarid region of Argentina: Chaco and La Pampa. Samples were collected from 1 ha square fields at 13.5, 50 and 150 cm height. Results showed that at higher heights the concentrations of glyphosate and AMPA were mostly higher. The glyphosate concentration was more variable and higher in Chaco (0.66 to 313 µg kg-1) than in La Pampa (4.17 to 114 µg kg-1). These results may be due to the higher use of herbicides in Chaco, where the predominant crops are soybeans and corn, produced under no-tillage. Under these conditions the use of glyphosate for weeds control is a common practice. Conversely, AMPA concentrations were higher in La Pampa (13.1 to 101.3 µg kg-1) than in Chaco (1.3 to 83 µg kg-1). These preliminary results show high concentrations of glyphosate and AMPA in wind eroded materials of agricultural soils of Argentina. More research is needed to confirm these high concentrations in other conditions in order to detect the temporal and spatial distribution patterns of the herbicide.

Study of UV cloud modification factors in Southern Patagonia

NASA Astrophysics Data System (ADS)

Wolfram, Elian A.; Orte, Facundo; Salvador, Jacobo; Quiroga, Jonathan; D'Elia, Raúl; Antón, Manuel; Alados-Arboledas, Lucas; Quel, Eduardo

2017-02-01

Anthropogenic perturbation of the ozone layer has induced change in the amount of UV radiation that reaches the Earth's surface, mainly through the Antarctic ozone hole, making the ozone and ultraviolet (UV) radiation two important issues in the study of Earth atmosphere in the scientific community. Also the clouds have been identified as the main modulator of UV amount in short time scales and produce the main source of uncertainty in the projection of surface UV level as consequence of projected ozone recovery. While clouds can decrease direct radiation, they can produce an increase in the diffuse component, and as consequence the surface UV radiation may be higher than an equivalent clear sky scenario for several minutes. In particular this situation can be important when low ozone column and partially cloud cover skies happen simultaneously. These situations happen frequently in southern Patagonia, where the CEILAP Lidar Division has established the Atmospheric Observatory of Southern Patagonia, an atmospheric remote sensing site near the city of Río Gallegos (51°55'S, 69°14'W). In this paper, the impact of clouds over the UV radiation is investigated by the use of ground based measurements from the passive remote sensing instruments operating at this site, mainly of broad and moderate narrow band filter radiometers. We analyzed the UV Index obtained from a multiband filter radiometer GUV-541 (UVI) [Biospherical Inc.] installed in the Observatorio Atmosférico de la Patagonia Austral, Río Gallegos, since 2005. Cloud modification factors (CMF, ratio between the measured UV radiation in a cloudy sky and the simulated radiation under cloud-free conditions) are evaluated for the study site. The database used in this work covers the period 2005-2012 for spring and summer seasons, when the ozone hole can affect these subpolar regions. CMF higher than 1 are found during spring and summer time, when lower total ozone columns, higher solar elevations and high cloud cover occur simultaneously, producing extreme erythemal irradiance at ground surface. Enhancements as high as 25% were registered. The maximum duration of the enhancement was around 30 minute. This produces dangerous sunbathing situations for the Río Gallegos citizen.

Aescin formation in calli and embryoids from cotyledon and stem explants of Aesculus hippocastanum L.

PubMed

Profumo, P; Caviglia, A M; Gastaldo, P

1994-11-01

Aescin in calli and embryoids obtained from both cotyledon and stem explants of Aesculus hippocastanum were investigated by HPLC. Determinations were carried out on tissues cultured in agarized medium supplemented with growth substances (2,4-dichlorophenoxyacetic acid; kinetin; 1-naphthaleneacetic acid). The results indicate that aescin was produced in all the analysed samples. The amount of active principle present in some samples was higher than that found in horse-chestnut seeds.

Lexical Link Analysis Application: Improving Web Service to Acquisition Visibility Portal Phase III

DTIC Science & Technology

2015-04-30

It is a supervised learning method but best for Big Data with low dimensions. It is an approximate inference good for Big Data and Hadoop ...Each process produces large amounts of information ( Big Data ). There is a critical need for automation, validation, and discovery to help acquisition...can inform managers where areas might have higher program risk and how resource and big data management might affect the desired return on investment

The global Cretaceous-Tertiary fire: Biomass or fossil carbon

NASA Technical Reports Server (NTRS)

Gilmour, Iain; Guenther, Frank

1988-01-01

The global soot layer at the K-T boundary indicates a major fire triggered by meteorite impact. However, it is not clear whether the principal fuel was biomass or fossil carbon. Forests are favored by delta value of C-13, which is close to the average for trees, but the total amount of elemental C is approximately 10 percent of the present living carbon, and thus requires very efficient conversion to soot. The PAH was analyzed at Woodside Creek, in the hope of finding a diagnostic molecular marker. A promising candidate is 1-methyl-7-isopropyl phenanthrene (retene,), which is probably derived by low temperature degradation of abietic acid. Unlike other PAH that form by pyrosynthesis at higher temperatures, retene has retained the characteristic side chains of its parent molecule. A total of 11 PAH compounds were identified in the boundary clay. Retene is present in substantial abundance. The identification was confirmed by analysis of a retene standard. Retene is characteristic of the combustion of resinous higher plants. Its formation depends on both temperature and oxygen access, and is apparently highest in oxygen-poor fires. Such fires would also produce soot more efficiently which may explain the high soot abundance. The relatively high level of coronene is not typical of a wood combustion source, however, though it can be produced during high temperature pyrolysis of methane, and presumably other H, C-containing materials. This would require large, hot, low O2 zones, which may occur only in very large fires. The presence of retene indicates that biomass was a significant fuel source for the soot at the Cretaceous-Tertiary boundary. The total amount of elemental C produced requires a greater than 3 percent soot yield, which is higher than typically observed for wildfires. However, retene and presumably coronene imply limited access of O2 and hence high soot yield.

Gibberellins Producing Endophytic Fungus Porostereum spadiceum AGH786 Rescues Growth of Salt Affected Soybean

PubMed Central

Hamayun, Muhammad; Hussain, Anwar; Khan, Sumera A.; Kim, Ho-Youn; Khan, Abdul L.; Waqas, Muhammad; Irshad, Muhammad; Iqbal, Amjad; Rehman, Gauhar; Jan, Samin; Lee, In-Jung

2017-01-01

In the pursuit of sustainable agriculture through environment and human health friendly practices, we evaluated the potential of a novel gibberellins (GAs) producing basidiomycetous endophytic fungus Porostereum spadiceum AGH786, for alleviating salt stress and promoting health benefits of soybean. Soybean seedlings exposed to different levels of NaCl stress (70 and 140 mM) under greenhouse conditions, were inoculated with the AGH786 strain. Levels of phytohormones including GAs, JA and ABA, and isoflavones were compared in control and the inoculated seedlings to understand the mechanism through which the stress is alleviated. Gibberellins producing endophytic fungi have been vital for promoting plant growth under normal and stress conditions. We report P. spadiceum AGH786 as the ever first GAs producing basidiomycetous fungus capable of producing six types of GAs. In comparison to the so for most efficient GAs producing Gibberella fujikuroi, AGH786 produced significantly higher amount of the bioactive GA3. Salt-stressed phenotype of soybean seedlings was characterized by low content of GAs and high amount of ABA and JA with reduced shoot length, biomass, leaf area, chlorophyll contents, and rate of photosynthesis. Mitigation of salt stress by AGH786 was always accompanied by high GAs, and low ABA and JA, suggesting that this endophytic fungus reduces the effect of salinity by modulating endogenous phytohormones of the seedlings. Additionally, this strain also enhanced the endogenous level of two isoflavones including daidzen and genistein in soybean seedlings under normal as well as salt stress conditions as compared to their respective controls. P. spadiceum AGH786 boosted the NaCl stress tolerance and growth in soybean, by modulating seedlings endogenous phytohormones and isoflavones suggesting a valuable contribution of this potent fungal biofertilizer in sustainable agriculture in salt affected soils. PMID:28473818

Investigation of the effect of resistivity on scrape off layer filaments using three-dimensional simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Easy, L., E-mail: le590@york.ac.uk; CCFE, Culham Science Centre, Abingdon OX14 3DB; Militello, F.

2016-01-15

The propagation of filaments in the Scrape Off Layer (SOL) of tokamaks largely determines the plasma profiles in the region. In a conduction limited SOL, parallel temperature gradients are expected, such that the resistance to parallel currents is greater at the target than further upstream. Since the perpendicular motion of an isolated filament is largely determined by balance of currents that flow through it, this may be expected to affect filament transport. 3D simulations have thus been used to study the influence of enhanced parallel resistivity on the dynamics of filaments. Filaments with the smallest perpendicular length scales, which weremore » inertially limited at low resistivity (meaning that polarization rather than parallel currents determines their radial velocities), were unaffected by resistivity. For larger filaments, faster velocities were produced at higher resistivities due to two mechanisms. First parallel currents were reduced and polarization currents were enhanced, meaning that the inertial regime extended to larger filaments, and second, a potential difference formed along the parallel direction so that higher potentials were produced in the region of the filament for the same amount of current to flow into the sheath. These results indicate that broader SOL profiles could be produced at higher resistivities.« less

The Comparative Effect of Carrot and Lemon Fiber as a Fat Replacer on Physico-chemical, Textural, and Organoleptic Quality of Low-fat Beef Hamburger.

PubMed

Soncu, Eda Demirok; Kolsarıcı, Nuray; Çiçek, Neslihan; Öztürk, Görsen Salman; Akoğlu, Ilker T; Arıcı, Yeliz Kaşko

2015-01-01

This study was designed to determine the usability of lemon fiber (LF-2%, 4%, 6%) and carrot fiber (CF-2%, 4%, 6%) to produce low-fat beef hamburgers. To that end, a certain amount of fat was replaced with each fiber. The proximate composition, pH value, cholesterol content, cooking characteristics, color, texture profile, and sensory properties of low-fat beef hamburgers were investigated. LF increased moisture content and cooking yield due to its better water binding properties, while CF caused higher fat and cholesterol contents owing to its higher fat absorption capacity (p<0.05). LF resulted in a lighter, redder, and more yellow color (p<0.05). Hardness, gumminess, springiness, and chewiness parameters decreased when the usage level of both fibers increased (p<0.05). However, more tender, gummy, springy, and smoother hamburgers were produced by the addition of CF in comparison with LF (p<0.05). Moreover, hamburgers including CF were rated with higher sensory scores (p<0.05). In conclusion, LF demonstrated better technological results in terms of cooking yield, shrinkage, moisture retention, and fat retention. However it is suggested that CF produces better low-fat hamburgers since up to 2% CF presented sensory and textural properties similar to those of regular hamburgers.

Quantification of Trichothecene-Producing Fusarium Species in Harvested Grain by Competitive PCR To Determine Efficacies of Fungicides against Fusarium Head Blight of Winter Wheat

PubMed Central

Edwards, S. G.; Pirgozliev, S. R.; Hare, M. C.; Jenkinson, P.

2001-01-01

We developed a PCR-based assay to quantify trichothecene-producing Fusarium based on primers derived from the trichodiene synthase gene (Tri5). The primers were tested against a range of fusarium head blight (FHB) (also known as scab) pathogens and found to amplify specifically a 260-bp product from 25 isolates belonging to six trichothecene-producing Fusarium species. Amounts of the trichothecene-producing Fusarium and the trichothecene mycotoxin deoxynivalenol (DON) in harvested grain from a field trial designed to test the efficacies of the fungicides metconazole, azoxystrobin, and tebuconazole to control FHB were quantified. No correlation was found between FHB severity and DON in harvested grain, but a good correlation existed between the amount of trichothecene-producing Fusarium and DON present within grain. Azoxystrobin did not affect levels of trichothecene-producing Fusarium compared with those of untreated controls. Metconazole and tebuconazole significantly reduced the amount of trichothecene-producing Fusarium in harvested grain. We hypothesize that the fungicides affected the relationship between FHB severity and the amount of DON in harvested grain by altering the proportion of trichothecene-producing Fusarium within the FHB disease complex and not by altering the rate of DON production. The Tri5 quantitative PCR assay will aid research directed towards reducing amounts of trichothecene mycotoxins in food and animal feed. PMID:11282607

Characterization of Heat Melt Compactor (HMC) Product Water

NASA Technical Reports Server (NTRS)

Harris, Linden; Wignarajah, Kanapathipi; Alba, Richard Gilbert; Pace, Gregory S.; Fisher, John W.

2013-01-01

The Heat Melt Compactor (HMC) is designed to sterilize and process wastes produced during space missions. Benefits of the HMC include reduction of biohazards to the crew, reduction in volume of wastes that would otherwise require storage, production of radiation shielding tiles, and recovery of water and other resources. Water reuse is critical onboard spacecrafts; it reduces the need for resupply missions and saves valuable storage space. The main sources of water in HMC batches are food, beverages, shampoo, disinfecting wipes, toothpaste, and diapers. Water reclaimed by the HMC was analyzed for concentrations of Na+, NH4+, K+, Mg2+, Ca2+, Cl-­-, NO2-­-, Br-­-, NO3-­-, PO43-­-, SO42-­-, total organic carbon (TOC), total inorganic carbon (TIC), % total solids, and pH. The data are discussed in relation to the current water input characteristics established for the International Space Station Water Processor Assembly system. Batches with higher than average amounts of food produced HMC product water with higher sulfate content, and batches with higher proportions of disinfectant wipes and food yielded HMC product water with higher ammonium concentration. We also compared theoretical chemical composition of HMC product water based on food labels and literature values to experimental results.

Dissociative properties of 1,1,1,2-tetrafluoroethane obtained by computational chemistry

NASA Astrophysics Data System (ADS)

Hayashi, Toshio; Ishikawa, Kenji; Sekine, Makoto; Hori, Masaru

2018-06-01

The electronic properties and dissociative channels of the alternative to the CCl2F2 (CFC-12) refrigerant, 1,1,1,2-tetrafluoroethane (HFC-134a) with a low global warming potential (GWP, 1430), were revealed by computational chemistry. The results show that CF3 + and CHF2 + ions are mainly produced by ionization. The CF3CH2 + ion is produced by ion pair formation and by direct ionization in the energy region higher than approximately 15 eV, but also in small amounts by the ionization of the dissociated CF3CH2 radical. This information is useful for etching process engineers in leading-edge semiconductor manufacturing.

Effects of acetylsalicylic acid on fresh weight pigment and protein content of bean leaf discs (Phaseolus vulgaris L.).

PubMed

Canakçi, S

2003-01-01

The effects of 100, 250, and 500 ppm acetylsalicylic acid solutions treatments on weight alteration, pigment and protein amounts in discs from the primary leaves of one month old bean (Phaseolus vulgaris L.) seedlings produced tinder greenhouse conditions are presented. The experiments show that: 100 ppm ASA had no significant influence (P > 0.05) but 250 and 500 ppm ASA caused an increase on weight loss (P < 0.01); ASA at higher concentrations (250 and 500 ppm), generally, caused a decrease on pigment amounts (P < 0.05-P < 0.01) but 100 ppm ASA had no considerably significant influence on them (P > 0.05), none of the ASA treatments caused a statistically significant influence on carotenoid amount (P > 0.05); 100 and 250 ppm ASA treatments did not cause a significant influence on protein amount (P > 0.05). however 500 ppm ASA treatment caused an increase on protein injury (P < 0.05). Consequently, it is supposed that wet weight loss, pigment and protein injury have somewhat increased on leaf discs. depending on the toxic effect of high acetylsalicylic acid concentrations.

Effect of filler content on mechanical and dynamic mechanical properties of particulate biphasic calcium phosphate--polylactide composites.

PubMed

Bleach, N C; Nazhat, S N; Tanner, K E; Kellomäki, M; Törmälä, P

2002-04-01

A bioabsorbable self-reinforced polylactide/biphasic calcium phosphate (BCP) composite is being developed for fracture fixation plates. One manufacturing route is to produce preimpregnated sheets by pulling polylactide (PLA) fibres through a suspension of BCP filler in a PLA solution and compression moulding the prepreg to the desired shape. To aid understanding of the process, interactions between the matrix and filler were investigated. Composite films containing 0-0.25 volume fraction filler, produced by solvent casting, were analysed using SEM, tensile testing and dynamic mechanical analysis (DMA). Homogeneous films could be made, although some particle agglomeration was seen at higher filler volume fractions. As the filler content increased, the failure strain decreased due to a reduction in the amount of ductile polymer present and the ultimate tensile strength (UTS) decreased because of agglomeration and void formation at higher filler content. The matrix glass transition temperature increased due to polymer chain adsorption and immobilization onto the BCP particles. Complex damping mechanisms, such as particle-particle agglomeration, may exist at the higher BCP volume fractions.

Biorhythms in the activity of children during free play1

PubMed Central

Wade, M. G.; Ellis, M. J.; Bohrer, R. E.

1973-01-01

The interaction between the arousal to action of environmental stimuli and recovery from that activity was presumed to generate biorhythms in the activity level of children. The level of environmental stimuli was manipulated by varying the play-group size and the apparatus, and higher environmental complexity was expected to produce more pronounced rhythms. The heart rates of 16 subjects playing in monad, dyad, and tetrad group sizes, in two playroom configurations, were monitored and spectral analysis used to locate significant biorhythms. There was a tendency toward 40-min (slow frequency) and 15-min (fast frequency) biorhythms. The group size manipulation produced the strongest biorhythmic behavior in the dyadic groups. Apparatus differences were not significant but the configuration containing a minimum quantity of play apparatus produced more variable activity than the configuration containing a large amount of play apparatus. PMID:4714575

Biorhythms in the activity of children during free play.

PubMed

Wade, M G; Ellis, M J; Bohrer, R E

1973-07-01

The interaction between the arousal to action of environmental stimuli and recovery from that activity was presumed to generate biorhythms in the activity level of children. The level of environmental stimuli was manipulated by varying the play-group size and the apparatus, and higher environmental complexity was expected to produce more pronounced rhythms. The heart rates of 16 subjects playing in monad, dyad, and tetrad group sizes, in two playroom configurations, were monitored and spectral analysis used to locate significant biorhythms. There was a tendency toward 40-min (slow frequency) and 15-min (fast frequency) biorhythms. The group size manipulation produced the strongest biorhythmic behavior in the dyadic groups. Apparatus differences were not significant but the configuration containing a minimum quantity of play apparatus produced more variable activity than the configuration containing a large amount of play apparatus.

Production of sophorolipid glycolipid biosurfactants from sugarcane molasses using Starmerella bombicola NBRC 10243.

PubMed

Takahashi, Makoto; Morita, Tomotake; Wada, Koji; Hirose, Naoto; Fukuoka, Tokuma; Imura, Tomohiro; Kitamoto, Dai

2011-01-01

Biosurfactants (BS) are produced by a variety of microorganisms from renewable resources, and have unique properties compared to chemical surfactants. In order to attain efficient production of BS from low-cost materials, we focused our attention on the use of sugarcane molasses. Fifteen yeast strains that are known as BS producers were examined for BS productivity from a culture medium consisting of only molasses and water. Among the strains tested, only Starmerella bombicola NBRC 10243 produced sophorolipids (SL), which are glycolipid BS. The culture conditions for the yeast were then investigated in a shake-flask culture. SL production was significantly affected by the pH of the medium and was highly accelerated at pH 6. Under the optimum conditions, the amount of SL reached 14.4 g/L after 120 h from a medium containing 150 g/L of total sugars. We tried to improve the production of SL further by feeding the molasses using a jar fermentor. Interestingly, the amount of SL increased up to 22.8 g/L after 120 h; the production rate was 1.6-fold higher than that in the shake-flask culture. These results suggest that the present yeast should have great potential for the low-cost production of SL, and facilitate the application of BS in various fields.

Thermodynamic Considerations of Direct Oxygen Removal from Titanium by Utilizing the Deoxidation Capability of Rare Earth Metals

NASA Astrophysics Data System (ADS)

Okabe, Toru H.; Zheng, Chenyi; Taninouchi, Yu-ki

2018-06-01

Oxygen removal from metallic Ti is extremely difficult and, currently, there is no commercial process for effectively deoxidizing Ti or its alloys. The oxygen concentration in Ti scraps is normally higher than that in virgin metals such as in Ti sponges produced by the Kroll process. When scraps are remelted with virgin metals for producing primary ingots of Ti or its alloys, the amount of scrap that can be used is limited owing to the accumulation of oxygen impurities. Future demands of an increase in Ti production and of mitigating environmental impacts require that the amount of scrap recycled as a feed material of Ti ingots should also increase. Therefore, it is important to develop methods for removing oxygen directly from Ti scraps. In this study, we evaluated the deoxidation limit for β-Ti using Y or light rare earth metals (La, Ce, Pr, or Nd) as a deoxidant. Thermodynamic considerations suggest that extra-low-oxygen Ti, with an oxygen concentration of 100 mass ppm or less can be obtained using a molten salt equilibrating with rare earth metals. The results presented herein also indicate that methods based on molten salt electrolysis for producing rare earth metals can be utilized for effectively and directly deoxidizing Ti scraps.

Improving Plant Nitrogen Use Efficiency through Alteration of Amino Acid Transport Processes1[OPEN

PubMed Central

Perchlik, Molly

2017-01-01

Improving the efficiency of nitrogen (N) uptake and utilization in plants could potentially increase crop yields while reducing N fertilization and, subsequently, environmental pollution. Within most plants, N is transported primarily as amino acids. In this study, pea (Pisum sativum) plants overexpressing AMINO ACID PERMEASE1 (AAP1) were used to determine if and how genetic manipulation of amino acid transport from source to sink affects plant N use efficiency. The modified plants were grown under low, moderate, or high N fertilization regimes. The results showed that, independent of the N nutrition, the engineered plants allocate more N via the vasculature to the shoot and seeds and produce more biomass and higher seed yields than wild-type plants. Dependent on the amount of N supplied, the AAP1-overexpressing plants displayed improved N uptake or utilization efficiency, or a combination of the two. They also showed significantly increased N use efficiency in N-deficient as well as in N-rich soils and, impressively, required half the amount of N to produce as many fruits and seeds as control plants. Together, these data support that engineering N allocation from source to sink presents an effective strategy to produce crop plants with improved productivity as well as N use efficiency in a range of N environments. PMID:28733388

BREEDING EXPERIMENTS ON MEDICINAL PLANTS. 27. ROENTGEN MUTATIONS AND ACTIVE SUBSTANCE CONTENT IN DATURA (in German)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steinegger, E.; Zbinden, F.

1961-10-01

The changes in alkaloid content of the Datura stramonium var. godronii are considered. About 1000 plants cultivated from irradiated and nonlrradiated seeds were examined for changes in total alkaloid content. In about 1.5% of the plants the alknloid content changed considerably, the decreases being more marked than the increases. Completely alkaloid-free plants, however, were not produced, in spite of the fact that occasionally the alkaloid content was so low that it could no longer be determined. There were two groups of mutants with increased alkaloid content. Some pharmaceutically important plants with higher total alkaloid production per plant and with loweredmore » alkaloid drug yield had double chromosome numbers and proved to be autotetraploid. However, the alkaloid contents of these plants were not higher than those of the artificially cultivated polyploids. The alkaloid content was evaluated by paper chromatography, which made possible the extraction of minute amounts of water- soluble basic amines as well as preventing the secondary changes of alkaloids. New alkaloids were not detected. Scopolamine content was found to decrease with age of the plant. In some mutants a reciprocal change in the amounts of some alkaloids could be demonstrated. A mutant containing a large amount of cuskohygrine was detected. (BBB)« less

Effects of marine toxins on the reproduction and early stages development of aquatic organisms.

PubMed

Vasconcelos, Vítor; Azevedo, Joana; Silva, Marisa; Ramos, Vítor

2010-01-19

Marine organisms, and specially phytoplankton species, are able to produce a diverse array of toxic compounds that are not yet fully understood in terms of their main targets and biological function. Toxins such as saxitoxins, tetrodotoxin, palytoxin, nodularin, okadaic acid, domoic acid, may be produced in large amounts by dinoflagellates, cyanobacteria, bacteria and diatoms and accumulate in vectors that transfer the toxin along food chains. These may affect top predator organisms, including human populations, leading in some cases to death. Nevertheless, these toxins may also affect the reproduction of aquatic organisms that may be in contact with the toxins, either by decreasing the amount or quality of gametes or by affecting embryonic development. Adults of some species may be insensitive to toxins but early stages are more prone to intoxication because they lack effective enzymatic systems to detoxify the toxins and are more exposed to the toxins due to a higher metabolic growth rate. In this paper we review the current knowledge on the effects of some of the most common marine toxins on the reproduction and development of early stages of some organisms.

To postpone the precipitation of manganese oxides in the degradation of tetrachloroethylene by controlling the permanganate concentration.

PubMed

Yang, Weiwei; Qiu, Zhaofu; Zhao, Zhexuan; Lu, Shuguang; Sui, Qian; Gu, Xiaogang

2017-01-01

Controlled-release permanganate (CRP) is a relatively new technology used to treat contaminated groundwater. This study tested the encapsulation of permanganate using stearic acid to realize controlled-release properties. Batch experiments were conducted to investigate the performance of manganese oxides (MnO 2 ) in the reaction between CRP and the contaminant of interest: tetrachloroethylene (PCE). The results showed that higher ionic strengths (I = 0.1 mol/L) cause earlier precipitation of MnO 2 colloids. Using CRP to degrade PCE could decrease the amount of MnO 2 colloids produced and postpone precipitation compared to raw potassium permanganate (KMnO 4 ) under high ionic strength conditions by controlling the KMnO 4 concentration in the solution. The amount of MnO 2 colloids produced and the time of precipitation depended more on the CRP grain size than on the CRP mass ratio. Controlling the KMnO 4 concentration used in the reaction could control the formation of MnO 2 precipitates in the premise of guarantee the removal rate of PCE.

Plant-associated methylobacteria as co-evolved phytosymbionts: a hypothesis.

PubMed

Kutschera, Ulrich

2007-03-01

Due to their wall-associated pectin metabolism, growing plant cells emit significant amounts of the one-carbon alcohol methanol. Pink-pigmented microbes of the genus Methylobacterium that colonize the surfaces of leaves (epiphytes) are capable of growth on this volatile C1-compound as sole source of carbon and energy. In this article the results of experiments with germ-free (gnotobiotic) sporophytes of angiosperms (sunflower, maize) and gametophytes of bryophytes (a moss and two liverwort species) are summarized. The data show that methylobacteria do not stimulate the growth of these angiosperms, but organ development in moss protonemata and in thalli of liverworts is considerably enhanced. Since methylobacteria produce and secrete cytokinins and auxin, a model of plant-microbe-interaction (symbiosis) is proposed in which the methanol-consuming bacteria are viewed as coevolved partners of the gametophyte that determine its growth, survival and reproduction (fitness). This symbiosis is restricted to the haploid cells of moisture-dependent "living fossil" plants; it does not apply to the diploid sporophytes of higher embryophytes, which are fully adapted to life on land and apparently produce sufficient amounts of endogenous phytohormones.

Plant-Associated Methylobacteria as Co-Evolved Phytosymbionts

PubMed Central

2007-01-01

Due to their wall-associated pectin metabolism, growing plant cells emit significant amounts of the one-carbon alcohol methanol. Pink-pigmented microbes of the genus Methylobacterium that colonize the surfaces of leaves (epiphytes) are capable of growth on this volatile C1-compound as sole source of carbon and energy. In this article the results of experiments with germ-free (gnotobiotic) sporophytes of angiosperms (sunflower, maize) and gametophytes of bryophytes (a moss and two liverwort species) are summarized. The data show that methylobacteria do not stimulate the growth of these angiosperms, but organ development in moss protonemata and in thalli of liverworts is considerably enhanced. Since methylobacteria produce and secrete cytokinins and auxin, a model of plant-microbe-interaction (symbiosis) is proposed in which the methanol-consuming bacteria are viewed as coevolved partners of the gametophyte that determine its growth, survival and reproduction (fitness). This symbiosis is restricted to the haploid cells of moisture-dependent “living fossil” plants; it does not apply to the diploid sporophytes of higher embryophytes, which are fully adapted to life on land and apparently produce sufficient amounts of endogenous phytohormones. PMID:19516971

Determination Hypoiodous Acid (HIO) By Peroxidase System Using Peroxidase Enzyme

NASA Astrophysics Data System (ADS)

Al-Baarri, A. N.; Legowo, A. M.; Widayat; Abduh, S. B. M.; Hadipernata, M.; Wisnubroto; Ardianti, D. K.; Susanto, M. N.; Yusuf, M.; Demasta, E. K.

2018-02-01

It has been understood that peroxidase enzyme including peroxidase serves as catalyzer to enzymatic reaction among hydrogen peroxide and halides, therefore this research was done for generating hypoiodous acid (HIO) from peroxidase system using peroxidase enzyme. Hydrogen peroxide, potassium iodide, and peroxidase enzyme were used to produce HIO. Determination the amount of formed HIO was done using 2,2'-azino-bis(3- ethylbenzothiazoline-6-sulphonic acid) or ABTS as substrate through the colorimetric measurement of hydrogen peroxide residue during reaction process using at 412 nm. The result indicated that residual hydrogen peroxide showed the minimum concentration after 60 minutes reaction time. Because the reaction started at the beginning time of mixing, hydrogen peroxide was unable to be eliminated totally to produce HIO. The reaction of peroxidase system was able to determine the beginning of mixing process but the reaction process could not eliminate the initial concentration of hydrogen peroxide indicating the maximum amount of production of HIO could be determined. In conclusion, the less of H2O2, higher HIO obtained and peroxidase enzymes can accelerate the formation of HIO.

Reverse Engineering of Corinthian Pigment Processing and Firing Technologies on Archaic Polychrome Ceramics

NASA Astrophysics Data System (ADS)

Klesner, Catherine Elizabeth

Decorative, polychrome ceramics from Corinth, Greece, produced during the 8th-6th centuries B.C.E. are luxury goods that were widely traded throughout Greece and the Mediterranean. The decorated ceramics were produced in a variety of shapes, including aryballos, alabastron, and olpe. They were decorated with slip-glazes in distinctive white, black, red, yellow, and purple colors, and in a variety of surface finishes, matte, semi-matte and glossy. Artisans in Corinthian workshops experimented to change the colors of the slips by varying the type and amount of iron-rich raw materials. They also varied the composition of the clay used as a binder and the amount of flux used as a sintering aid to promote glass formation. This research reconstructs the technology used by the Corinthian craftsmen to produce the Archaic polychrome ceramics, and shows how these technologies differed from the production of better known, more prestigious Athenian black-figure and red-figure ceramics. Through microstructural examination of archaeological samples and replication experiments, this thesis proposes that the purple iron oxide pigment is the result of acid treatment and oxidation of iron metal. The firing temperature range of the Corinthian polychrome ceramics was determined experimentally to be 925-1025°C, which is higher than previously reported and similar to that reported for Corinthian transport amphoras. The firing range is higher by 50-150°C than the Athenian black-figure and red-figure ceramics. Samples of Corinthian polychrome and Athenian black-figure ceramics from the Marie Farnsworth collection at the University of Arizona were tested and compared to Corinthian clay collections. Analytical techniques included Fourier-transform infrared spectroscopy (FTIR), scanning-electron microscopy with energy-dispersive spectroscopy (SEM-EDS), micro-Raman spectroscopy, and wavelength-dispersive electron microprobe (EPMA with BSE-SEM).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rogers, Jameson K.; Church, George M.

Here, engineering cells to produce valuable metabolic products is hindered by the slow and laborious methods available for evaluating product concentration. Consequently, many designs go unevaluated, and the dynamics of product formation over time go unobserved. In this work, we develop a framework for observing product formation in real time without the need for sample preparation or laborious analytical methods. We use genetically encoded biosensors derived from small-molecule responsive transcription factors to provide a fluorescent readout that is proportional to the intracellular concentration of a target metabolite. Combining an appropriate biosensor with cells designed to produce a metabolic product allowsmore » us to track product formation by observing fluorescence. With individual cells exhibiting fluorescent intensities proportional to the amount of metabolite they produce, high-throughput methods can be used to rank the quality of genetic variants or production conditions. We observe production of several renewable plastic precursors with fluorescent readouts and demonstrate that higher fluorescence is indeed an indicator of higher product titer. Using fluorescence as a guide, we identify process parameters that produce 3-hydroxypropionate at 4.2 g/L, 23-fold higher than previously reported. We also report, to our knowledge, the first engineered route from glucose to acrylate, a plastic precursor with global sales of 14 billion. Finally, we monitor the production of glucarate, a replacement for environmentally damaging detergents, and muconate, a renewable precursor to polyethylene terephthalate and nylon with combined markets of 51 billion, in real time, demonstrating that our method is applicable to a wide range of molecules.« less

PREPARATION OF URANIUM TRIOXIDE

DOEpatents

Buckingham, J.S.

1959-09-01

The production of uranium trioxide from aqueous solutions of uranyl nitrate is discussed. The uranium trioxide is produced by adding sulfur or a sulfur-containing compound, such as thiourea, sulfamic acid, sulfuric acid, and ammonium sulfate, to the uranyl solution in an amount of about 0.5% by weight of the uranyl nitrate hexahydrate, evaporating the solution to dryness, and calcining the dry residue. The trioxide obtained by this method furnished a dioxide with a considerably higher reactivity with hydrogen fluoride than a trioxide prepared without the sulfur additive.

Method of Forming Three-Dimensional Semiconductors Structures

NASA Technical Reports Server (NTRS)

Fathauer, Robert W. (Inventor)

2002-01-01

Silicon and metal are coevaporated onto a silicon substrate in a molecular beam epitaxy system with a larger than stoichiometric amount of silicon so as to epitaxially grow columns of metal silicide embedded in a matrix of single crystal, epitaxially grown silicon. Higher substrate temperatures and lower deposition rates yield larger columns that are farther apart while more silicon produces smaller columns. Column shapes and locations are selected by seeding the substrate with metal silicide starting regions. A variety of 3-dimensional, exemplary electronic devices are disclosed.

Dose-equivalent neutron dosimeter

DOEpatents

Griffith, R.V.; Hankins, D.E.; Tomasino, L.; Gomaa, M.A.M.

1981-01-07

A neutron dosimeter is disclosed which provides a single measurement indicating the amount of potential biological damage resulting from the neutron exposure of the wearer, for a wide range of neutron energies. The dosimeter includes a detecting sheet of track etch detecting material such as a carbonate plastic, for detecting higher energy neutrons, and a radiator layer contaning conversion material such as /sup 6/Li and /sup 10/B lying adjacent to the detecting sheet for converting moderate energy neutrons to alpha particles that produce tracks in the adjacent detecting sheet.

Cold-pressed and hot-pressed rapeseed oil: The effects of roasting and seed moisture on the antioxi- dant activity, canolol, and tocopherol level.

PubMed

Siger, Aleksander; Józefiak, Marta; Górnaś, Paweł

2017-01-01

The paper looks at the levels of canolol, tocopherols and antioxidant activity in cold-pressed and hot-pressed rapeseed oils produced from seeds of various moisture levels (5%, 7.5%, and 10%). The paper also considers the effects of seed roasting on the levels of these compounds. The material used for the tests was rapeseed cv. Adrianna. The quality of the oils obtained is determined using peroxide and acid values. The levels of canolol and tocopherols are analyzed using HPLC. The DPPH radical-scavenging activity method for oil samples and phenolic extract from oils was used. It has been demonstrated that the oils produced from rapeseeds with a 5% moisture content, and   in particular from cold-pressed oils, were characterized by the lowest peroxide values. Cold-pressed oils produced from rapeseeds with a 5% moisture content were characterized by higher levels of tocopherols and plastochromanol-8. In the case of hot-pressed oils, the highest levels of tocopherols were found in oils pro- duced from seeds with a 7.5% moisture content, and the greatest amount of PC-8 (more than 4 mg/100 g) was found in oils produced from seeds with a 10% moisture content. Hot-pressed oils have been shown to have higher levels of these compounds than cold-pressed oils. Both roasting and hot pressing led to an increase in the amount of canolol in the oils investigated. When analysing the antioxidant activity of the oils and phenolic extracts it was shown that phenolic compounds are responsible for approx. 10% of total antioxidant activity. Various levels of biologically active compounds were shown to be present in the rapeseed oil obtained from raw materials of a varying moisture content. The type of pressing process (cold-pressing or hot-pressing) and whether the seeds have undergone roasting has also been shown to affect the resulting oil and the level of native antioxidants it contains.

27 CFR 19.245 - Bonds and penal sums of bonds.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Distiller The amount of tax on spirits produced during a period of 15 days $5,000 $100,000 (ii) Warehouseman... gallons ......do 5,000 50,000 (iii) Distiller and warehouseman The amount of tax on spirits produced... transit to bonded premises 10,000 200,000 (iv) Distiller and processor The amount of tax on spirits...

S-(−)equol producing status not associated with breast cancer risk among low isoflavone consuming US postmenopausal women undergoing a physician recommended breast biopsy

PubMed Central

Virk-Baker, Mandeep K.; Barnes, Stephen; Krontiras, Helen; Nagy, Tim R.

2014-01-01

Soy foods are the richest sources of isoflavones, mainly daidzein and genistein. Soy isoflavones are structurally similar to the steroid hormone 17β-estradiol and may protect against breast cancer. S-(−)equol, a metabolite of the soy isoflavone daidzein, has a higher bioavailability and greater affinity for estrogen receptor-β than daidzein. About one third of the Western population is able to produce S-(−)equol, and the ability is linked to certain gut microbes. We hypothesized that the prevalence of breast cancer, ductal hyperplasia, and overall breast pathology will be lower among S-(−)equol producing, as compared to non -producing, postmenopausal women undergoing a breast biopsy. We tested our hypothesis using a cross-sectional study design. Usual diets of the participants were supplemented with one soy bar per day for three consecutive days. Liquid chromatography-multiple reaction ion monitoring mass spectrometry analysis of urine from 143 subjects revealed 25 (17.5%) as S-(−)equol producers. We found no statistically significant associations between S-(−)equol producing status and overall breast pathology (OR 0.68; 95% CI 0.23 – 1.89), ductal hyperplasia (OR 0.84; 95% CI 0.20 – 3.41), or breast cancer (OR 0.56; 95% CI 0.16 – 1.87). However, the mean dietary isoflavones intake was much lower (0.3 mg/day) than in previous reports. Given that the amount of S-(−)equol produced in the gut depends on the amount of daidzein exposure, the low soy intake coupled with lower prevalence of S-(−)equol producing status in the study population favors towards null associations. Findings from our study could be used for further investigations on S-(−)equol producing status and disease risk. PMID:24461312

Staphylococcus epidermidis and Staphylococcus haemolyticus: detection of biofilm genes and biofilm formation in blood culture isolates from patients in a Brazilian teaching hospital.

PubMed

Pinheiro, Luiza; Brito, Carla Ivo; Oliveira, Adilson de; Pereira, Valéria Cataneli; Cunha, Maria de Lourdes Ribeiro de Souza da

2016-09-01

Infections with coagulase-negative staphylococci are often related to biofilm formation. This study aimed to detect biofilm formation and biofilm-associated genes in blood culture isolates of Staphylococcus epidermidis and S. haemolyticus. Half (50.6%) of the 85 S. epidermidis isolates carried the icaAD genes and 15.3% the bhp gene, while these numbers were 42.9% and 0 for S. haemolyticus, respectively. According to the plate test, 30 S. epidermidis isolates were biofilm producers and 40% of them were strongly adherent, while only one (6%) of the 17 S. haemolyticus biofilm-producing isolates exhibited a strongly adherent biofilm. The concomitant presence of icaA and icaD was significantly associated with the plate and tube test results (P ≤ 0.0004). The higher frequency of icaA in S. epidermidis and of icaD in S. haemolyticus is correlated with the higher biofilm-producing capacity of the former since, in contrast to IcaD, IcaA activity is sufficient to produce small amounts of polysaccharide. Although this study emphasizes the importance of icaAD and bhp for biofilm formation in S. epidermidis, other mechanisms seem to be involved in S. haemolyticus. Copyright © 2016 Elsevier Inc. All rights reserved.

Optimization of mass spectrometric parameters improve the identification performance of capillary zone electrophoresis for single-shot bottom-up proteomics analysis.

PubMed

Zhang, Zhenbin; Dovichi, Norman J

2018-02-25

The effects of MS1 injection time, MS2 injection time, dynamic exclusion time, intensity threshold, and isolation width were investigated on the numbers of peptide and protein identifications for single-shot bottom-up proteomics analysis using CZE-MS/MS analysis of a Xenopus laevis tryptic digest. An electrokinetically pumped nanospray interface was used to couple a linear-polyacrylamide coated capillary to a Q Exactive HF mass spectrometer. A sensitive method that used a 1.4 Th isolation width, 60,000 MS2 resolution, 110 ms MS2 injection time, and a top 7 fragmentation produced the largest number of identifications when the CZE loading amount was less than 100 ng. A programmable autogain control method (pAGC) that used a 1.4 Th isolation width, 15,000 MS2 resolution, 110 ms MS2 injection time, and top 10 fragmentation produced the largest number of identifications for CZE loading amounts greater than 100 ng; 7218 unique peptides and 1653 protein groups were identified from 200 ng by using the pAGC method. The effect of mass spectrometer conditions on the performance of UPLC-MS/MS was also investigated. A fast method that used a 1.4 Th isolation width, 30,000 MS2 resolution, 45 ms MS2 injection time, and top 12 fragmentation produced the largest number of identifications for 200 ng UPLC loading amount (6025 unique peptides and 1501 protein groups). This is the first report where the identification number for CZE surpasses that of the UPLC at the 200 ng loading level. However, more peptides (11476) and protein groups (2378) were identified by using UPLC-MS/MS when the sample loading amount was increased to 2 μg with the fast method. To exploit the fast scan speed of the Q-Exactive HF mass spectrometer, higher sample loading amounts are required for single-shot bottom-up proteomics analysis using CZE-MS/MS. Copyright © 2017 Elsevier B.V. All rights reserved.

The Relationship of Loss, Mean Age of Air and the Distribution of CFC's to Stratospheric Circulation and Implications for Atmospheric Lifetimes

NASA Technical Reports Server (NTRS)

Douglas, A. R.; Stolarski, R. S.; Schoeberl, M. R.; Jackman, C. H.; Gupta, M. L.; Newman, P. A.; Nielsen, J. E.; Fleming, E. L.

2008-01-01

Model-derived estimates of the annually integrated destruction and lifetime for various ozone depleting substances (ODSs) depend on the simulated stratospheric transport and mixing in the global model used to produce the estimate. Observations in the middle and high latitude lower stratosphere show that the mean age of an air parcel (i.e., the time since its stratospheric entry) is related to the fractional release for the ODs (i.e., the amount of the ODS that has been destroyed relative to the amount at the time of stratospheric entry). We use back trajectory calculations to produce an age spectrum, and explain the relationship between the mean age and the fractional release by showing that older elements in the age spectrum have experienced higher altitudes and greater ODs destruction than younger elements. In our study, models with faster circulations produce distributions for the age-of-air that are 'young' compared to a distribution derived from observations. These models also fail to reproduce the observed relationship between the mean age of air and the fractional release. Models with slower circulations produce both realistic distributions for mean age and a realistic relationship between mean age and fractional release. These models also produce a CFCl3 lifetime of approximately 56 years, longer than the 45 year lifetime used to project future mixing ratios. We find that the use of flux boundary conditions in assessment models would have several advantages, including consistency between ODS evolution and simulated loss even if the simulated residual circulation changes due to climate change.

Reverse microemulsion synthesis of layered gadolinium hydroxide nanoparticles

NASA Astrophysics Data System (ADS)

Xu, Yadong; Suthar, Jugal; Egbu, Raphael; Weston, Andrew J.; Fogg, Andrew M.; Williams, Gareth R.

2018-02-01

A reverse microemulsion approach has been explored for the synthesis of layered gadolinium hydroxide (LGdH) nanoparticles in this work. This method uses oleylamine as a multifunctional agent, acting as surfactant, oil phase and base. 1-butanol is additionally used as a co-surfactant. A systematic study of the key reaction parameters was undertaken, including the volume ratio of surfactant (oleylamine) to water, the reaction time, synthesis temperature, and the amount of co-surfactant (1-butanol) added. It proved possible to obtain pristine LGdH materials at temperatures of 120 °C or below with an oleylamine: water ratio of 1:4. Using larger amounts of surfactant or higher temperatures caused the formation of Gd(OH)3, either as the sole product or as a major impurity phase. The LGdH particles produced have sizes of ca. 200 nm, with this size being largely independent of temperature or reaction time. Adjusting the amount of 1-butanol co-surfactant added permits the size to be varied between 200 and 300 nm.

Nutritional evaluation of low-phytate peas (Pisum sativum L.) for young broiler chicks.

PubMed

Thacker, Philip; Deep, Aman; Petri, Daniel; Warkentin, Thomas

2013-02-01

This experiment determined the effects of including normal and low-phytate peas in diets fed to young broiler chickens on performance, phosphorus availability and bone strength. A total of 180, day-old, male broilers (Ross-308 line) were assigned to six treatments. The control was based on corn and soybean meal while two additional corn-based diets were formulated containing 30% of either normal or low-phytate pea providing 0.45% available phosphorus. For each of these three diets, a similar diet was formulated by reducing the amount of dicalcium phosphate to produce a diet with 0.3% available phosphorus. The total tract apparent availability (TTAA) of phosphorus was higher (p = 0.02) for broilers fed the low-phytate pea than for birds fed the normal pea diets. Birds fed diets containing the lower level of phosphorus had a higher TTAA of phosphorus (50.64 vs. 46.68%) than broilers fed diets adequate in phosphorus. Protein source had no effect on weight gain, feed intake or feed conversion. Broilers fed the low phosphorus diets had lower weight gain (p = 0.04) and feed intake (p < 0.01) than broilers fed the higher phosphorus level. Bone strength was higher (p < 0.01) for broilers fed diets based on low-phytate pea than for those fed diets based on normal pea or soybean meal. Increasing the availability of the phosphorus in peas could mean that less inorganic phosphorus would be required in order to meet the nutritional requirements of broilers. Since inorganic phosphorus sources tend to be expensive, a reduction in their use would lower ration costs. In addition, increased availability of phosphorus would reduce the amount of phosphorus excreted thus reducing the amount of phosphorus that can potentially pollute the environment.

Enhanced hot-electron production and strong-shock generation in hydrogen-rich ablators for shock ignition

NASA Astrophysics Data System (ADS)

Theobald, W.; Bose, A.; Yan, R.; Betti, R.; Lafon, M.; Mangino, D.; Christopherson, A. R.; Stoeckl, C.; Seka, W.; Shang, W.; Michel, D. T.; Ren, C.; Nora, R. C.; Casner, A.; Peebles, J.; Beg, F. N.; Ribeyre, X.; Llor Aisa, E.; Colaïtis, A.; Tikhonchuk, V.; Wei, M. S.

2017-12-01

Experiments were performed with CH, Be, C, and SiO2 ablators interacting with high-intensity UV laser radiation (5 × 1015 W/cm2, λ = 351 nm) to determine the optimum material for hot-electron production and strong-shock generation. Significantly more hot electrons are produced in CH (up to ˜13% instantaneous conversion efficiency), while the amount is a factor of ˜2 to 3 lower in the other ablators. A larger hot-electron fraction is correlated with a higher effective ablation pressure. The higher conversion efficiency in CH is attributed to stronger damping of ion-acoustic waves because of the presence of light H ions.

Difficulties in maintaining long-term partial nitritation of ammonium-rich sludge digester liquids in a moving-bed biofilm reactor (MBBR).

PubMed

Fux, C; Huang, D; Monti, A; Siegrist, H

2004-01-01

Nitrogen can be eliminated effectively from sludge digester effluents by anaerobic ammonium oxidation (anammox), but 55-60% of the ammonium must first be oxidized to nitrite. Although a continuous flow stirred tank reactor (CSTR) with suspended biomass could be used, its hydraulic dilution rate is limited to 0.8-1 d(-1) (30 degrees C). Higher specific nitrite production rates can be achieved by sludge retention, as shown here for a moving-bed biofilm reactor (MBBR) with Kaldnes carriers on laboratory and pilot scales. The maximum nitrite production rate amounted to 2.7 gNO2-Nm(-2)d(-1) (3 gO2m(-3)d(-1), 30.5 degrees C), thus doubling the dilution rate compared to CSTR operation with suspended biomass for a supernatant with 700 gNH4-Nm(-3). Whenever the available alkalinity was fully consumed, an optimal amount of nitrite was produced. However, a significant amount of nitrate was produced after 11 months of operation, making the effluent unsuitable for anaerobic ammonium oxidation. Because the sludge retention time (SRT) is relatively long in biofilm systems, slow growth of nitrite oxidizers occurs. None of the selection criteria applied - a high ammonium loading rate, high free ammonia or low oxygen concentration - led to selective suppression of nitrite oxidation. A CSTR or SBR with suspended biomass is consequently recommended for full-scale operation.

[Study of biological value of beef produced by interspecies hybrids of domestic cattle and wild yaks].

PubMed

Bagirov, V A; Chernukha, I M; Lisitsin, A V; Zinovieva, N A

2014-01-01

The comparative study of the chemical composition and biological values of beef produced by hybrids of Angus cattle with wild yaks (hybrid beef) and pure-bred Angus cattle (traditional beef) has been carried out. Longissimus muscle samples were used for analysis. It was observed, that the hybrid beef samples had the practically equal protein content comparing to traditional beef (21.1 vs. 21.6 per cent) but were characterized by the lower fat content (1.2 vs. 2.5 per cent). The higher biological value of hybrid beef comparing to traditional beef has been shown. The value of protein-quality index, calculated as the ratio of tryptophan amino acid to oxyprolin and characterizing the ratio of high biological value proteins to low biological value proteins was 8.1 vs. 5.7. The values of amino acid indexes [ratio of essential amino acids (EAA) to non-essential amino acids (NAA) and ratio of EAA to the total amount of amino acids (TAA)] were EAA/NAA = 0.77 vs. 0.65 and EAA/TAA = 0.43 vs. 0.39. The protein of hybrid beef was characterized by the higher content of a number of the essential amino acids: by a factor of 1, 77 for threonin, 1.23--for valin, 1.09--for lysin, 1.17--for leucine and 1.19--for tryptophan. The amount of the essential amino acids in 1 gram of protein of the hybrid beef was 434.7 mg against 393.1 mg for traditional beef It has been shown, that the protein of the hybrid beef comparing to traditional beef is characterized by the higher values of the amino acid scores calculated for EAA.

Enhancing Fatty Acid Production of Saccharomyces cerevisiae as an Animal Feed Supplement.

PubMed

You, Seung Kyou; Joo, Young-Chul; Kang, Dae Hee; Shin, Sang Kyu; Hyeon, Jeong Eun; Woo, Han Min; Um, Youngsoon; Park, Chulhwan; Han, Sung Ok

2017-12-20

Saccharomyces cerevisiae is used for edible purposes, such as human food or as an animal feed supplement. Fatty acids are also beneficial as feed supplements, but S. cerevisiae produces small amounts of fatty acids. In this study, we enhanced fatty acid production of S. cerevisiae by overexpressing acetyl-CoA carboxylase, thioesterase, and malic enzyme associated with fatty acid metabolism. The enhanced strain pAMT showed 2.4-fold higher fatty acids than the wild-type strain. To further increase the fatty acids, various nitrogen sources were analyzed and calcium nitrate was selected as an optimal nitrogen source for fatty acid production. By concentration optimization, 672 mg/L of fatty acids was produced, which was 4.7-fold higher than wild-type strain. These results complement the low level fatty acid production and make it possible to obtain the benefits of fatty acids as an animal feed supplement while, simultaneously, maintaining the advantages of S. cerevisiae.

Understanding of polyhydroxybutyrate production under carbon and phosphorus-limited growth conditions in non-axenic continuous culture.

PubMed

Cavaillé, Laëtitia; Albuquerque, Maria; Grousseau, Estelle; Lepeuple, Anne-Sophie; Uribelarrea, Jean-Louis; Hernandez-Raquet, Guillermina; Paul, Etienne

2016-02-01

In a waste into resource strategy, a selection of polyhydroxybutyrate (PHB)-accumulating organisms from activated sludge was achieved in an open continuous culture under acetic acid and phosphorus limitation. Once the microbial population was selected at a dilution rate (D), an increase in phosphorus limitation degree was applied in order to study the intracellular phosphorus plasticity of selected bacteria and the resulting capacity to produce PHB. Whatever D, all selected populations were able to produce PHB. At a D, the phosphorus availability determined the phosphorus-cell content which in turn fixed the amount of cell. All the remaining carbon was thus directed toward PHB. By decreasing D, microorganisms adapted more easily to higher phosphorus limitation leading to higher PHB content. A one-stage continuous reactor operated at D=0.023h(-)(1) gave reliable high PHB productivity with PHB content up to 80%. A two-stage reactor could ensure better productivity while allowing tuning product quality. Copyright © 2015 Elsevier Ltd. All rights reserved.

Polymethoxylated flavones, flavanone glycosides, carotenoids, and antioxidants in different cultivation types of tangerines ( Citrus reticulata Blanco cv. Sainampueng) from Northern Thailand.

PubMed

Stuetz, Wolfgang; Prapamontol, Tippawan; Hongsibsong, Surat; Biesalski, Hans-Konrad

2010-05-26

Polymethoxylated flavones (PMFs) and flavanone glycosides (FGs) were analyzed in hand-pressed juice and the peeled fruit of 'Sainampueng' tangerines ( Citrus reticulata Blanco cv. Sainampueng) grown in northern Thailand. The tangerines were collected from a citrus cluster of small orchard farmers and were cultivated as either agrochemical-based (AB), agrochemical-safe (AS), or organic grown fruits. Juice samples were also measured on contents of carotenoids, ascorbic acid, and tocopherols. The peel-deriving PMFs tangeretin, nobiletin, and sinensetin were found with high concentrations in juice as a result of simple squeezing, whereas amounts of those PMFs were negligibly low in peeled tangerine fruit. In contrast, the mean concentrations of the FGs narirutin, hesperidin, and didymin were several fold higher in peeled fruit than in tangerine juice and significantly higher in organic than AS and AB tangerines. Narirutin and hesperidin in juice from organic produces as well as narirutin in juice from AS produces were significantly higher than respective mean concentrations in juice from AB produces. beta-Cryptroxanthin was the predominant carotenoid beside zeaxanthin, lutein, lycopene, and beta-carotene in tangerine juice. Ascorbic acid concentrations were not predicted by the type of cultivation, whereas alpha-tocopherol was significantly higher in juice from organic than AS produces. In summary, hand-pressed juice of C. reticulata Blanco cv. Sainampueng serves as a rich source of PMFs, FGs, carotenoids, and antioxidants: 4-5 tangerine fruits ( approximately 80 g of each fruit) giving one glass of 200 mL hand-pressed juice would provide more than 5 mg of nobiletin and tangeretin and 36 mg of hesperidin, narirutin, and didymin, as well as 30 mg of ascorbic acid, >1 mg of provitamin A active beta-cryptoxanthin, and 200 microg of alpha-tocopherol.

Willingness to pay for a reduction in mortality risk after a myocardial infarction: an application of the contingent valuation method to the case of eplerenone.

PubMed

Pinto-Prades, Jose-Luis; Farreras, Veronica; de Bobadilla, Jaime Fernandez

2008-02-01

In order to allocate health care resources more efficiently, it is necessary to relate health improvements provided by new medicines to their cost. It is necessary to ascertain when the additional cost of introducing a new health technology is justified by the additional health gain produced. Eplerenone is a new medicine that reduces the risk of death after myocardial infarction (MI) but produces additional cost to the health system. The contingent valuation approach can be used to measure the monetary value of this risk reduction and to estimate society's willingness to pay (WTP) for a new medicine that reduces the risk of death after MI by 2% points. We used a contingent valuation approach to evaluate WTP amongst members of the general population. We used the ex-ante and the ex-post approach. In the ex-ante approach, subjects are asked if they would accept an increase in their taxes in order to have access to eplerenone should they need it in the future. In the ex-post approach, subjects are asked if they would pay a certain amount of money as co-payment per month during 5 years if they suffered an MI. We used the dichotomous choice method, using five bids in each approach. The WTP was estimated using both single-bound and double-bound dichotomous choice (SBDC, DBDC). Extensive piloting (n = 187) preceded the final survey (n = 350). The WTP in the ex-ante case was euro 58 per year under both SBDC and DBDC. In the ex-post case, monthly WTP was euro 141 for the SBDC and euro 85 for the DBDC. Subjects with higher income and subjects with a higher perception of risk showed a higher WTP (P 0.05). Society is willing to pay an additional amount of money in order to give eplerenone to present and future patients. We estimate that euro 85 per month is a conservative estimate of the monetary value of a 2% risk reduction in mortality after MI and to spend this additional amount of money in Eplerenone can be considered an efficient policy.

Ensuring Resiliency of the Milk and Dairy Industry in California

DTIC Science & Technology

2011-12-01

cannot be zero. Also, the upper bound cannot exceed the capacity of raw milk that the milk producing cows can make in each county. Between the...the amount of milk producing cows in each county and multiplying by the daily average amount of raw milk produced. RawMilkProd = NumMilkProdCows...the total number of milk producing cows . 365 TotalMilkProdDailyAvgAmtMilkProdPerCow TotalMilkProdCows = × We get the number of milk producing cows

Sonochemical and hydrodynamic cavitation reactors for laccase/hydrogen peroxide cotton bleaching.

PubMed

Gonçalves, Idalina; Martins, Madalena; Loureiro, Ana; Gomes, Andreia; Cavaco-Paulo, Artur; Silva, Carla

2014-03-01

The main goal of this work is to develop a novel and environmental-friendly technology for cotton bleaching with reduced processing costs. This work exploits a combined laccase-hydrogen peroxide process assisted by ultrasound. For this purpose, specific reactors were studied, namely ultrasonic power generator type K8 (850 kHz) and ultrasonic bath equipment Ultrasonic cleaner USC600TH (45 kHz). The optimal operating conditions for bleaching were chosen considering the highest levels of hydroxyl radical production and the lowest energy input. The capacity to produce hydroxyl radicals by hydrodynamic cavitation was also assessed in two homogenizers, EmulsiFlex®-C3 and APV-2000. Laccase nanoemulsions were produced by high pressure homogenization using BSA (bovine serum albumin) as emulsifier. The bleaching efficiency of these formulations was tested and the results showed higher whiteness values when compared to free laccase. The combination of laccase-hydrogen peroxide process with ultrasound energy produced higher whiteness levels than those obtained by conventional methods. The amount of hydrogen peroxide was reduced 50% as well as the energy consumption in terms of temperature (reduction of 40 °C) and operating time (reduction of 90 min). Copyright © 2013 Elsevier Inc. All rights reserved.

Unbalance Response Prediction for Rotors on Ball Bearings Using Speed and Load Dependent Nonlinear Bearing Stiffness

NASA Technical Reports Server (NTRS)

Fleming, David P.; Poplawski, J. V.

2003-01-01

Rolling-element bearing forces vary nonlinearly with bearing deflection. Thus an accurate rotordynamic analysis requires that bearing forces corresponding to the actual bearing deflection be utilized. For this work bearing forces were calculated by COBRA-AHS, a recently developed rolling-element bearing analysis code. Bearing stiffness was found to be a strong function of bearing deflection, with higher deflection producing markedly higher stiffness. Curves fitted to the bearing data for a range of speeds and loads were supplied to a flexible rotor unbalance response analysis. The rotordynamic analysis showed that vibration response varied nonlinearly with the amount of rotor imbalance. Moreover, the increase in stiffness as critical speeds were approached caused a large increase in rotor and bearing vibration amplitude over part of the speed range compared to the case of constant bearing stiffness. Regions of bistable operation were possible, in which the amplitude at a given speed was much larger during rotor acceleration than during deceleration. A moderate amount of damping will eliminate the bistable region, but this damping is not inherent in ball bearings.

Catalytic conversion of biomass pyrolysis-derived compounds with chemical liquid deposition (CLD) modified ZSM-5.

PubMed

Zhang, Huiyan; Luo, Mengmeng; Xiao, Rui; Shao, Shanshan; Jin, Baosheng; Xiao, Guomin; Zhao, Ming; Liang, Junyu

2014-03-01

Chemical liquid deposition (CLD) with KH550, TEOS and methyl silicone oil as the modifiers was used to modify ZSM-5 and deposit its external acid sites. The characteristics of modified catalysts were tested by catalytic conversion of biomass pyrolysis-derived compounds. The effects of different modifying conditions (deposited amount, temperature, and time) on the product yields and selectivities were investigated. The results show KH550 modified ZSM-5 (deposited amount of 4%, temperature of 20°C and time of 6h) produced the maximum yields of aromatics (24.5%) and olefins (16.5%), which are much higher than that obtained with original ZSM-5 catalyst (18.8% aromatics and 9.8% olefins). The coke yield decreased from 44.1% with original ZSM-5 to 26.7% with KH550 modified ZSM-5. The selectivities of low-molecule-weight hydrocarbons (ethylene and benzene) decreased, while that of higher molecule-weight hydrocarbons (propylene, butylene, toluene, and naphthalene) increased comparing with original ZSM-5. Copyright © 2013 Elsevier Ltd. All rights reserved.

Artificial selection reveals the energetic expense of producing larger eggs.

PubMed

Pick, Joel L; Hutter, Pascale; Ebneter, Christina; Ziegler, Ann-Kathrin; Giordano, Marta; Tschirren, Barbara

2016-01-01

The amount of resources provided by the mother before birth has important and long-lasting effects on offspring fitness. Despite this, there is a large amount of variation in maternal investment seen in natural populations. Life-history theory predicts that this variation is maintained through a trade-off between the benefits of high maternal investment for the offspring and the costs of high investment for the mother. However, the proximate mechanisms underlying these costs of reproduction are not well understood. Here we used artificial selection for high and low maternal egg investment in a precocial bird, the Japanese quail (Coturnix japonica) to quantify costs of maternal reproductive investment. We show that females from the high maternal investment lines had significantly larger reproductive organs, which explained their overall larger body mass, and resulted in a higher resting metabolic rate (RMR). Contrary to our expectations, this increase in metabolic activity did not lead to a higher level of oxidative damage. This study is the first to provide experimental evidence for metabolic costs of increased per offspring investment.

Highly photostable NV centre ensembles in CVD diamond produced by using N2O as the doping gas

NASA Astrophysics Data System (ADS)

Tallaire, A.; Mayer, L.; Brinza, O.; Pinault-Thaury, M. A.; Debuisschert, T.; Achard, J.

2017-10-01

High density Nitrogen-Vacancy (NV) centre ensembles incorporated in plasma assisted chemical vapour deposition (CVD) diamond are crucial to the development of more efficient sensing devices that use the properties of luminescent defects. Achieving high NV doping with N2 as the dopant gas source during diamond growth is, however, plagued by the formation of macroscopic and point defects that quench luminescence. Moreover, such NVs are found to exhibit poor photostability under high laser powers. Although this effect can be harnessed to locally and durably switch off NV luminescence for data storage, it is usually undesirable for most applications. In this work, the use of N2O as an alternative doping source is proposed. Much higher amounts of the doping gas can be added without significantly generating defects, which allows the incorporation of perfectly photostable and higher density NV ensembles. This effect is believed to be related to the lower dissociation energy of the N2O molecule together with the beneficial effect of the presence of a low and controlled amount of oxygen near the growing surface.

The type of carbohydrates specifically selects microbial community structures and fermentation patterns.

PubMed

Chatellard, Lucile; Trably, Eric; Carrère, Hélène

2016-12-01

The impact on dark fermentation of seven carbohydrates as model substrates of lignocellulosic fractions (glucose, cellobiose, microcrystalline cellulose, arabinose, xylose, xylan and wheat straw) was investigated. Metabolic patterns and bacterial communities were characterized at the end of batch tests inoculated with manure digestate. It was found that hydrogen production was linked to the sugar type (pentose or hexose) and the degree of polymerisation. Hexoses produced less hydrogen, with a specific selection of lactate-producing bacterial community structures. Maximal hydrogen production was five times higher on pentose-based substrates, with specific bacterial community structures producing acetate and butyrate as main metabolites. Low hydrogen amounts accumulated from complex sugars (cellulose, xylan and wheat straw). A relatively high proportion of the reads was affiliated to Ruminococcaceae suggesting an efficient hydrolytic activity. Knowing that the bacterial community structure is very specific to a particular substrate offers new possibilities to design more efficient H 2 -producing biological systems. Copyright © 2016 Elsevier Ltd. All rights reserved.

Catalytic hydrothermal upgrading of crude bio-oils produced from different thermo-chemical conversion routes of microalgae.

PubMed

Duan, Peigao; Wang, Bing; Xu, Yuping

2015-06-01

This study presents experimental results that compare the use of hydrothermal liquefaction (HTL), alcoholysis (Al), pyrolysis (Py) and hydropyrolysis (HPy) for the production of bio-oil from a microalga (Chlorella pyrenoidosa) and the catalytic hydrothermal upgrading of crude bio-oils produced by these four conversion routes. The yields and compositions of bio-oil, solid residue, and gases were evaluated and compared. HTL resulted in a bio-oil that has a higher energy density and superior fuel properties, such as thermal and storage stabilities, compared with the other three conversion routes. The N in crude bio-oils produced from Py and HPy is more easily removed than that in the bio-oils produced from HTL and Al. The upgraded bio-oils contain reduced amounts of certain O-containing and N-containing compounds and significantly increased saturated hydrocarbon contents. All of the upgraded bio-oils have a larger fraction boiling below 350°C than their corresponding crude bio-oils. Copyright © 2015 Elsevier Ltd. All rights reserved.

Enhanced eicosapentaenoic acid production by a new deep-sea marine bacterium Shewanella electrodiphila MAR441T.

PubMed

Zhang, Jinwei; Burgess, J Grant

2017-01-01

Omega-3 fatty acids are products of secondary metabolism, essential for growth and important for human health. Although there are numerous reports of bacterial production of omega-3 fatty acids, less information is available on the biotechnological production of these compounds from bacteria. The production of eicosapentaenoic acid (EPA, 20:5ω3) by a new species of marine bacteria Shewanella electrodiphila MAR441T was investigated under different fermentation conditions. This strain produced a high percentage (up to 26%) of total fatty acids and high yields (mg / g of biomass) of EPA at or below the optimal growth temperature. At higher growth temperatures these values decreased greatly. The amount of EPA produced was affected by the carbon source, which also influenced fatty acid composition. This strain required Na+ for growth and EPA synthesis and cells harvested at late exponential or early stationary phase had a higher EPA content. Both the highest amounts (20 mg g-1) and highest percent EPA content (18%) occurred with growth on L-proline and (NH4)2SO4. The addition of cerulenin further enhanced EPA production to 30 mg g-1. Chemical mutagenesis using NTG allowed the isolation of mutants with improved levels of EPA content (from 9.7 to 15.8 mg g-1) when grown at 15°C. Thus, the yields of EPA could be substantially enhanced without the need for recombinant DNA technology, often a commercial requirement for food supplement manufacture.

Lipid composition in a strain of Bacillus subtilis, a producer of iturin A lipopeptides that are active against uropathogenic bacteria.

PubMed

Bernat, Przemysław; Paraszkiewicz, Katarzyna; Siewiera, Paulina; Moryl, Magdalena; Płaza, Grażyna; Chojniak, Joanna

2016-10-01

Urinary tract infections are a common disease in humans. Therefore, new methods are needed to destroy biofilms that are formed by uropathogens. Iturin A lipopeptides (LPs) C14 and C15 are potent biosurfactants synthetized by the Bacillus subtilis I'1a strain. The biological activity of extracted LPs was confirmed by examining extracts from I'1a cultures against uropathogenic bacteria that had been isolated from biofilms on urinary catheters. Compared with cultures of DSM 3257, which produce surfactin at a relatively low level, the extract obtained from strain I'1a exhibited a greater inhibitory effect against both planktonic and sessile forms of Escherichia coli, Serratia marcescens, Enterobacter cloacae, Proteus mirabilis, Citrobacter freundii and Enterococcus faecalis. Moreover, cyclic LP biosurfactants may disturb the integrity of cytoplasmic membranes; therefore, we investigated the effects of synthetized LPs on fatty acids and phospholipids of B. subtilis. LPs and lipids were analyzed using GC-MS, LC-MS/MS and MALDI-TOF/TOF techniques. Compared with B. subtilis DSM 3257, membranes of the I'1a strain were characterized by an increased amount of anteiso fatty acids and a ten-fold higher ratio of phosphatidylglycerol (PG)-to-phosphatidylethanolamine (PE). Interestingly, in cultures of B. subtilis DSM 3257 supplemented with LP extracts of the I'1a strain, the PG-to-PE ratio was fourfold higher, and the amount of anteiso fatty acids was also increased.

Enhanced eicosapentaenoic acid production by a new deep-sea marine bacterium Shewanella electrodiphila MAR441T

PubMed Central

Burgess, J. Grant

2017-01-01

Omega-3 fatty acids are products of secondary metabolism, essential for growth and important for human health. Although there are numerous reports of bacterial production of omega-3 fatty acids, less information is available on the biotechnological production of these compounds from bacteria. The production of eicosapentaenoic acid (EPA, 20:5ω3) by a new species of marine bacteria Shewanella electrodiphila MAR441T was investigated under different fermentation conditions. This strain produced a high percentage (up to 26%) of total fatty acids and high yields (mg / g of biomass) of EPA at or below the optimal growth temperature. At higher growth temperatures these values decreased greatly. The amount of EPA produced was affected by the carbon source, which also influenced fatty acid composition. This strain required Na+ for growth and EPA synthesis and cells harvested at late exponential or early stationary phase had a higher EPA content. Both the highest amounts (20 mg g-1) and highest percent EPA content (18%) occurred with growth on L-proline and (NH4)2SO4. The addition of cerulenin further enhanced EPA production to 30 mg g-1. Chemical mutagenesis using NTG allowed the isolation of mutants with improved levels of EPA content (from 9.7 to 15.8 mg g-1) when grown at 15°C. Thus, the yields of EPA could be substantially enhanced without the need for recombinant DNA technology, often a commercial requirement for food supplement manufacture. PMID:29176835

Origin of the outer layer of martian low-aspect ratio layered ejecta craters

NASA Astrophysics Data System (ADS)

Boyce, Joseph M.; Wilson, Lionel; Barlow, Nadine G.

2015-01-01

Low-aspect ratio layered ejecta (LARLE) craters are one of the most enigmatic types of martian layered ejecta craters. We propose that the extensive outer layer of these craters is produced through the same base surge mechanism as that which produced the base surge deposits generated by near-surface, buried nuclear and high-explosive detonations. However, the LARLE layers have higher aspect ratios compared with base surge deposits from explosion craters, a result of differences in thicknesses of these layers. This characteristics is probably caused by the addition of large amounts of small particles of dust and ice derived from climate-related mantles of snow, ice and dust in the areas where LARLE craters form. These deposits are likely to be quickly stabilized (order of a few days to a few years) from eolian erosion by formation of duricrust produced by diffusion of water vapor out of the deposits.

Room temperature synthesis of copper indium diselenide in non-aqueous solution using an organoindium reagent

NASA Technical Reports Server (NTRS)

Hepp, Aloysius F.; Andras, Maria T.; Bailey, Sheila G.; Duraj, Stan A.

1992-01-01

A novel two-phase synthesis of CuInSe2 at 25 C from Cu2Se and Cp3In in 4-methylpyridine has been discovered. Characterization of the material produced shows it to be platelet-shaped crystallites with an average particle size of 10 microns, less than 2 percent C and H, with a small amount of unidentified crystalline impurity. The results demonstrate that it is possible to produce from solution a material that is ordinarily synthesized in bulk or films at much higher temperatures or using extraneous reagents and/or electrons. The use of a solid-state reagent as a starting material which is converted to another solid-state compound by an organometallic reagent has tremendous potential to produce precursors for a wide range of solid-state materials of interest to the electronics, defense, and aerospace communities.

Precursors and factors affecting formation of haloacetonitriles and chloropicrin during chlor(am)ination of nitrogenous organic compounds in drinking water.

PubMed

Jia, Aiyin; Wu, Chunde; Duan, Yan

2016-05-05

This study investigated the precursors and factors affecting formation of haloacetonitriles (HANs) and chloropicrin (TCNM) during chlorination/chloramination of eight amino acids in the effluent water of V-type clarifying filtration from a drinking water treatment plant. The yields of trichloroacetonitrile (TCAN), dichloroacetonitrile (DCAN) and TCNM were higher during chlorination than during chloramination. Tyrosine and tryptophan produced the greatest amount of DCAN and also generated a small amount of TCAN during chlorination process. Besides, the yields of DCAN were higher than TCNM during chlorination/chloramination. Contact time, Cl2:org-N molar ratios, pH, temperature and bromide ion affected nitrogenous disinfection by-products (N-DBPs) formation during chlorination of tryptophan in different degrees. TCAN, DCAN and TCNM formation showed the increasing and then decreasing with prolonged contact time. Higher Cl2:org-N molar ratios improved N-DBPs formation within a certain range. The pH affected N-DBPs formation differently. HANs increased with increasing pH from 5 to 6 and decreased with increasing pH from 6 to 9, while TCNM increased with increasing pH from 5 to 9. Higher temperatures enhanced TCNM formation, but reduced the formation of TCAN and DCAN. The presence of bromide ions improved the yields of HANs and TCNM and shifted N-DBPs to more brominated ones. Copyright © 2016 Elsevier B.V. All rights reserved.

The Comparative Effect of Carrot and Lemon Fiber as a Fat Replacer on Physico-chemical, Textural, and Organoleptic Quality of Low-fat Beef Hamburger

PubMed Central

Soncu, Eda Demirok; Kolsarıcı, Nuray; Çiçek, Neslihan; Öztürk, Görsen Salman; Akoğlu, ilker T.; Arıcı, Yeliz Kaşko

2015-01-01

This study was designed to determine the usability of lemon fiber (LF-2%, 4%, 6%) and carrot fiber (CF-2%, 4%, 6%) to produce low-fat beef hamburgers. To that end, a certain amount of fat was replaced with each fiber. The proximate composition, pH value, cholesterol content, cooking characteristics, color, texture profile, and sensory properties of low-fat beef hamburgers were investigated. LF increased moisture content and cooking yield due to its better water binding properties, while CF caused higher fat and cholesterol contents owing to its higher fat absorption capacity (p<0.05). LF resulted in a lighter, redder, and more yellow color (p<0.05). Hardness, gumminess, springiness, and chewiness parameters decreased when the usage level of both fibers increased (p<0.05). However, more tender, gummy, springy, and smoother hamburgers were produced by the addition of CF in comparison with LF (p<0.05). Moreover, hamburgers including CF were rated with higher sensory scores (p<0.05). In conclusion, LF demonstrated better technological results in terms of cooking yield, shrinkage, moisture retention, and fat retention. However it is suggested that CF produces better low-fat hamburgers since up to 2% CF presented sensory and textural properties similar to those of regular hamburgers. PMID:26761851

Gender differences in tibio-femoral kinematics and quadriceps muscle force during weight-bearing knee flexion in vitro.

PubMed

Wünschel, Markus; Wülker, Nikolaus; Müller, Otto

2013-11-01

Females have a higher risk in terms of anterior cruciate ligament injuries during sports than males. Reasons for this fact may be different anatomy and muscle recruitment patterns leading to less protection for the cruciate- and collateral-ligaments. This in vitro study aims to evaluate gender differences in knee joint kinematics and muscle force during weight-bearing knee flexions. Thirty-four human knee specimens (17 females/17 males) were mounted on a dynamic knee simulator. Weight-bearing single-leg knee flexions were performed with different amounts of simulated body weight (BW). Gender-specific kinematics was measured with an ultrasonic motion capture system and different loading conditions were examined. Knee joint kinematics did not show significant differences regarding anteroposterior and medial-lateral movement as well as tibial varus-valgus and internal-external rotation. This applied to all simulated amounts of BW. Simulating 100 N BW in contrast to AF50 led to a significant higher quadriceps overall force in female knees from 45° to 85° of flexion in contrast to BW 50 N. In these female specimens, the quadriceps overall force was about 20 % higher than in male knees being constant in higher flexion angles. It is indicated by our results that in a squatting movement females compared with males produce higher muscle forces, suggesting an increased demand for muscular stabilization, whereas tibio-femoral kinematics was similar for both genders.

soil carbon pools within oak forest is endangered by global climate change in central mexico

NASA Astrophysics Data System (ADS)

García-Oliva, Felipe; Merino, Agustín; González-Rodriguez, Antonio; Chávez-Vergara, Bruno; Tapia-Torres, Yunuen; Oyama, Ken

2016-04-01

Forest soil represents the main C pool in terrestrial ecosystems. In particular, temperate forest ecosystems play an important role in the C budget among tropical countries, such as Mexico. For example, the temperate forest ecosystem contains higher C contents on average (295 Mg C ha-1) than the soil C associated with other ecosystems in Mexico (between 56 to 287 Mg C ha-1). At a regional scale, oak forest has the highest C content (460 Mg C ha-1) among the forest ecosystem in Michoacán State at Central Mexico. At the local scale, the soil C content is strongly affected by the composition of organic matter produced by the plant species. The oak species are very diverse in Mexico, distributed within two sections: Quercus sensu stricto and Lobatae. The oak species from Quercus s.s. section produced litterfall with lower concentrations of recalcitrant and thermostable compounds than oak species from Lobatae section, therefore the soil under the former species had higher microbial activity and nutrient availability than the soil under the later species. However, the forest fragment with higher amount of oak species from Quercus s.s. section increases the amount of soil C contents. Unfortunately, Quercus species distribution models for the central western region of Mexico predict a decrease of distribution area of the majority of oak species by the year 2080, as a consequence of higher temperatures and lower precipitation expected under climate change scenarios. Additionally to these scenarios, the remnant oak forest fragments suffer strong degradation due to uncontrolled wood extraction and deforestation. For this reason, the conservation of oak forest fragments is a priority to mitigate the greenhouse gases emission to the atmosphere. In order to enhance the protection of these forest fragments it is required that the society identify the ecosystem services that are provided by these forest fragments.

Secondary scintillation yield from GEM and THGEM gaseous electron multipliers for direct dark matter search

NASA Astrophysics Data System (ADS)

Monteiro, C. M. B.; Fernandes, L. M. P.; Veloso, J. F. C. A.; Oliveira, C. A. B.; dos Santos, J. M. F.

2012-07-01

The search for alternatives to PMTs as photosensors in optical TPCs for rare event detection has significantly increased in the last few years. In particular, in view of the next generation large volume detectors, the use of photosensors with lower natural radioactivity, such as large area APDs or GM-APDs, with the additional possibility of sparse surface coverage, triggered the intense study of secondary scintillation production in micropattern electron multipliers, such as GEMs and THGEMs, as alternatives to the commonly used uniform electric field region between two parallel meshes. The much higher scintillation output obtained from the electron avalanches in such microstructures presents an advantage in those situations. The accurate knowledge of the amount of such scintillation is important for correct detector simulation and optimization. It will also serve as a benchmark for software tools developed and/or under development for the calculation of the amount of such scintillation.The secondary scintillation yield, or electroluminescence yield, in the electron avalanches of GEMs and THGEMs operating in gaseous xenon and argon has been determined for different gas pressures. At 1 bar, THGEMs deliver electroluminescence yields that are more than one order of magnitude higher when compared to those achieved in GEMs and two orders of magnitude when compared to those achieved in a uniform field gap. The THGEM electroluminescence yield presents a faster decrease with pressure when comparing to the GEM electroluminescence yield, reaching similar values to what is achieved in GEMs for xenon pressures of 2.5 bar, but still one order of magnitude higher than that produced in a uniform field gap. Another exception is the GEM operating in argon, which presents an electroluminescence yield similar to that produced in a uniform electric field gap, while the THGEM achieves yields that are more than one order of magnitude higher.

The response of a simulated mesoscale convective system to increased aerosol pollution: Part I: Precipitation intensity, distribution, and efficiency

NASA Astrophysics Data System (ADS)

Clavner, Michal; Cotton, William R.; van den Heever, Susan C.; Saleeby, Stephen M.; Pierce, Jeffery R.

2018-01-01

Mesoscale Convective Systems (MCSs) are important contributors to rainfall in the High Plains of the United States and elsewhere in the world. It is therefore of interest to understand how different aerosols serving as cloud condensation nuclei (CCN) may impact the total amount, rates and spatial distribution of precipitation produced by MCSs. In this study, different aerosol concentrations and their effects on precipitation produced by an MCS are examined by simulating the 8 May 2009 "Super-Derecho" MCS using the Regional Atmospheric Modeling System (RAMS), a cloud-resolving model (CRM) with sophisticated aerosol and microphysical parameterizations. Three simulations were conducted that differed only in the initial concentration, spatial distribution, and chemical composition of aerosols. Aerosol fields were derived from the output of GEOS-Chem, a 3D chemical transport numerical model. Results from the RAMS simulations show that the total domain precipitation was not significantly affected by variations in aerosol concentrations, however, the pollution aerosols altered the precipitation characteristics. The more polluted simulations exhibited higher precipitation rates, higher bulk precipitation efficiency, a larger area with heavier precipitation, and a smaller area with lighter precipitation. These differences arose as a result of aerosols enhancing precipitation in the convective region of the MCS while suppressing precipitation from the MCS's stratiform-anvil. In the convective region, several processes likely contributed to an increase of precipitation. First, owing to the very humid environment of this storm, the enhanced amount of cloud water available to be collected overwhelmed the reduction in precipitation efficiency associated with the aerosol-induced production of smaller droplets which led to a net increase in the conversion of cloud droplets to precipitation. Second, higher aerosol concentrations led to invigoration of convective updrafts which enhanced precipitation in accordance to the convective invigoration hypothesis. The reduction in stratiform precipitation in the more polluted simulations was found to be attributed to the presence of greater aerosol number concentrations that reduced both collision-coalescence and riming. Analysis of back trajeocty flow showed that the air feeding the stratiform-anvil originated within the free troposphere, by mesoscale ascent. Therefore, increased aerosol pollution at higher elevations impacted the stratiform precipitation formation within the simulated MCS. As a consequence, the more polluted simulations produced the smallest precipitation from the MCS stratiform-anvil region. In Part II the impact of aerosols on the severe winds produced by this storm is examined.

Debranching and temperature-cycled crystallization of waxy rice starch and their digestibility.

PubMed

Zeng, Feng; Ma, Fei; Gao, Qunyu; Yu, Shujuan; Kong, Fansheng; Zhu, Siming

2014-11-26

Slowly digestible starch (SDS) was obtained through debranched waxy rice starch and subsequent crystallization under isothermal and temperature-cycled conditions. Temperature-cycled crystallization of dual 4/-20 °C produced a higher yield of SDS product than isotherm crystallization. Crystal structure of SDS products changed from A-type to a mixture of B and V-type X-ray diffraction patterns. The relative crystallinity was higher in the temperature-cycled samples than that of isotherm. Attenuated total reflectance Fourier transform infrared spectroscopy suggested that the peripheral regions of isothermal storage starch were better organized than temperature-cycles. Temperature cycling induced higher onset temperature for melting of crystals than isothermal storage under a differential scanning calorimeter. The cycled temperature storage induced a greater amount of SDS than the isothermal storage. Copyright © 2014 Elsevier Ltd. All rights reserved.

Xylem phenology and wood production: resolving the chicken-or-egg dilemma.

PubMed

Lupi, Carlo; Morin, Hubert; Deslauriers, Annie; Rossi, Sergio

2010-10-01

Delays in the start of the growing season reduce the period available for growth and the amount of xylem production. However, a higher number of developing tracheids could prolong cell differentiation and, consequently, lengthen the growing season. The relationship between the amount and duration of cell production in the xylem remains an unresolved issue. The aim of this study was to resolve the chicken-or-egg causality dilemma about duration of growth and cell production through simple- and double-cause models. This was achieved by (1) analysing the intra-annual growth dynamics of the xylem in Picea mariana (Mill.) BSP during 2006-2009 in two contrasting sites of the boreal forest of Quebec, Canada, and (2) extracting the dates of onset and ending of xylem formation and the number of radial cells along the tree ring. A higher number of cells was linked to an earlier onset (r=0.74) and later ending (r=0.61) of cell differentiation. The absence of a relationship between the residuals of the onset and ending of xylogenesis (r(p)=-0.06) indicated that cell production influenced the correlation between the two phenophases of the xylem. These results demonstrated that a higher number of cells produced delay the ending of xylem maturation, so extending the duration of wood formation. © 2010 Blackwell Publishing Ltd.

Effects of Copper and/or Cholesterol Overload on Mitochondrial Function in a Rat Model of Incipient Neurodegeneration

PubMed Central

Castillo, Omar; de Alaniz, María J. T.; Marra, Carlos A.

2013-01-01

Copper (Cu) and cholesterol (Cho) are both associated with neurodegenerative illnesses in humans and animals models. We studied the effect in Wistar rats of oral supplementation with trace amounts of Cu (3 ppm) and/or Cho (2%) in drinking water for 2 months. Increased amounts of nonceruloplasmin-bound Cu were observed in plasma and brain hippocampus together with a higher concentration of ceruloplasmin in plasma, cortex, and hippocampus. Cu, Cho, and the combined treatment Cu + Cho were able to induce a higher Cho/phospholipid ratio in mitochondrial membranes with a simultaneous decrease in glutathione content. The concentration of cardiolipin decreased and that of peroxidation products, conjugated dienes and lipoperoxides, increased. Treatments including Cho produced rigidization in both the outer and inner mitochondrial membranes with a simultaneous increase in permeability. No significant increase in Cyt C leakage to the cytosol was observed except in the case of cortex from rats treated with Cu and Cho nor were there any significant changes in caspase-3 activity and the Bax/Bcl2 ratio. However, the Aβ(1–42)/(1–40) ratio was higher in cortex and hippocampus. These findings suggest an incipient neurodegenerative process induced by Cu or Cho that might be potentiated by the association of the two supplements. PMID:24363953

Biological Conversion of Glycerol to Ethanol by Enterobacter aerogenes

NASA Astrophysics Data System (ADS)

Nwachukwu, Raymond E. S.

In a search to turn the economically and environmentally non-valuable "waste" streams of biodiesel production into a profitable byproduct, a mutant strain of Enterobacter aerogenes ATCC 13048 was developed by six-tube subculturing technique. This technique is based on the principle of adaptive evolution, and involved subculturing the bacterium in a tryptic soy broth without dextrose (TSB) containing specific glycerol and ethanol concentration for six consecutive times. Then, the six consecutive subculturing was repeated in a fresh TSB of higher glycerol and ethanol concentrations. A new mutant strain, E. aerogenes S012, which could withstand a combination of 200 g/l glycerol and 30 g/l ethanol concentrations, was developed. The wild and mutant strains were used for the fermentation of pure (P-) and recovered (R-) glycerol. Taguchi and full factorial methods of design of experiments were used to screen and optimize the important process factors that influence the microbial production of ethanol. A statistically sound regression model was used to establish the mathematical relationship between the process variables and ethanol production. Temperature of 38°C, agitation speed of 200 rpm, pH of 6.3-6.6, and microaerobic condition were the optimum process conditions. Different pretreatment methods to recover glycerol from the crude glycerol and the subsequent fermentation method showed that direct acidification using 85% H3PO4 was the best. The R-glycerol contained 51% pure glycerol and 21% methanol. The wild strain, E. aerogenes ATCC 13048, produced only 12 g/l and 12.8 g/l ethanol from 20 g/l P- and R-glycerol respectively, and could not utilize higher glycerol concentrations. The mutant, E. aerogenes S012, produced ethanol amount and yield of 43 g/l and 1.12 mol/mol-glycerol from P-glycerol, respectively within 96 h. It also produced ethanol amount and yield of 26.8 g/l and 1.07 mol/mol-glycerol, respectively, from R-glycerol within the same duration. In a fermentation to estimate hydrogen production using a respirometer, the hydrogen yield and volumetric rate of 1.06 mol/mol-glycerol and 217 ml/l/h, respectively were obtained from 6% P-glycerol in 72 h by E. aerogenes S012. The result was higher from R-glycerol, which produced hydrogen yield and productivity of 1.83 mol/mol-glycerol and 326 ml/l/h, respectively.

Yeast: the soul of beer's aroma--a review of flavour-active esters and higher alcohols produced by the brewing yeast.

PubMed

Pires, Eduardo J; Teixeira, José A; Brányik, Tomás; Vicente, António A

2014-03-01

Among the most important factors influencing beer quality is the presence of well-adjusted amounts of higher alcohols and esters. Thus, a heavy body of literature focuses on these substances and on the parameters influencing their production by the brewing yeast. Additionally, the complex metabolic pathways involved in their synthesis require special attention. More than a century of data, mainly in genetic and proteomic fields, has built up enough information to describe in detail each step in the pathway for the synthesis of higher alcohols and their esters, but there is still place for more. Higher alcohols are formed either by anabolism or catabolism (Ehrlich pathway) of amino acids. Esters are formed by enzymatic condensation of organic acids and alcohols. The current paper reviews the up-to-date knowledge in the pathways involving the synthesis of higher alcohols and esters by brewing yeasts. Fermentation parameters affecting yeast response during biosynthesis of these aromatic substances are also fully reviewed.

Genetically encoded sensors enable real-time observation of metabolite production

PubMed Central

Rogers, Jameson K.; Church, George M.

2016-01-01

Engineering cells to produce valuable metabolic products is hindered by the slow and laborious methods available for evaluating product concentration. Consequently, many designs go unevaluated, and the dynamics of product formation over time go unobserved. In this work, we develop a framework for observing product formation in real time without the need for sample preparation or laborious analytical methods. We use genetically encoded biosensors derived from small-molecule responsive transcription factors to provide a fluorescent readout that is proportional to the intracellular concentration of a target metabolite. Combining an appropriate biosensor with cells designed to produce a metabolic product allows us to track product formation by observing fluorescence. With individual cells exhibiting fluorescent intensities proportional to the amount of metabolite they produce, high-throughput methods can be used to rank the quality of genetic variants or production conditions. We observe production of several renewable plastic precursors with fluorescent readouts and demonstrate that higher fluorescence is indeed an indicator of higher product titer. Using fluorescence as a guide, we identify process parameters that produce 3-hydroxypropionate at 4.2 g/L, 23-fold higher than previously reported. We also report, to our knowledge, the first engineered route from glucose to acrylate, a plastic precursor with global sales of $14 billion. Finally, we monitor the production of glucarate, a replacement for environmentally damaging detergents, and muconate, a renewable precursor to polyethylene terephthalate and nylon with combined markets of $51 billion, in real time, demonstrating that our method is applicable to a wide range of molecules. PMID:26858408

Genetically encoded sensors enable real-time observation of metabolite production

DOE PAGES

Rogers, Jameson K.; Church, George M.

2016-02-08

Here, engineering cells to produce valuable metabolic products is hindered by the slow and laborious methods available for evaluating product concentration. Consequently, many designs go unevaluated, and the dynamics of product formation over time go unobserved. In this work, we develop a framework for observing product formation in real time without the need for sample preparation or laborious analytical methods. We use genetically encoded biosensors derived from small-molecule responsive transcription factors to provide a fluorescent readout that is proportional to the intracellular concentration of a target metabolite. Combining an appropriate biosensor with cells designed to produce a metabolic product allowsmore » us to track product formation by observing fluorescence. With individual cells exhibiting fluorescent intensities proportional to the amount of metabolite they produce, high-throughput methods can be used to rank the quality of genetic variants or production conditions. We observe production of several renewable plastic precursors with fluorescent readouts and demonstrate that higher fluorescence is indeed an indicator of higher product titer. Using fluorescence as a guide, we identify process parameters that produce 3-hydroxypropionate at 4.2 g/L, 23-fold higher than previously reported. We also report, to our knowledge, the first engineered route from glucose to acrylate, a plastic precursor with global sales of 14 billion. Finally, we monitor the production of glucarate, a replacement for environmentally damaging detergents, and muconate, a renewable precursor to polyethylene terephthalate and nylon with combined markets of 51 billion, in real time, demonstrating that our method is applicable to a wide range of molecules.« less

Evaluation of various cheese whey treatment scenarios in single-chamber microbial electrolysis cells for improved biohydrogen production.

PubMed

Rivera, Isaac; Bakonyi, Péter; Cuautle-Marín, Manuel Alejandro; Buitrón, Germán

2017-05-01

In this study single-chamber microbial electrolysis cells (MECs) were applied to treat cheese whey (CW), an industrial by-product, and recover H 2 gas. Firstly, this substrate was fed directly to the MEC to get the initial feedback about its H 2 generation potential. The results indicated that the direct application of CW requires an adequate pH control to realize bioelectrohydrogenesis and avoid operational failure due to the loss of bioanode activity. In the second part of the study, the effluents of anaerobic (methanogenic) digester and hydrogenogenic (dark fermentative H 2 -producing) reactor utilizing the CW were tested in the MEC process (representing the concept of a two-stage technology). It turned out that the residue of the methanogenic reactor - with its relatively lower carbohydrate- and higher volatile fatty acid contents - was more suitable to produce hydrogen bioelectrochemically. The MEC operated with the dark fermentation effluent, containing a high portion of carbohydrates and low amount of organic acids, produced significant amount of undesired methane simultaneously with H 2 . Overall, the best MEC behavior was attained using the effluent of the methanogenic reactor and therefore, considering a two-stage system, methanogenesis is an advisable pretreatment step for the acidic CW to enhance the H 2 formation in complementary microbial electrohydrogenesis. Copyright © 2017 Elsevier Ltd. All rights reserved.

Brain signatures of monetary loss and gain: outcome-related potentials in a single outcome gambling task

PubMed Central

Kamarajan, Chella; Porjesz, Bernice; Rangaswamy, Madhavi; Tang, Yongqiang; Chorlian, David B.; Padmanabhapillai, Ajayan; Saunders, Ramotse; Pandey, Ashwini K.; Roopesh, Bangalore N.; Manz, Niklas; Stimus, Arthur T.; Begleiter, Henri

2009-01-01

This study evaluates the event-related potential (ERP) components in a single outcome gambling task that involved monetary losses and gains. The participants were 50 healthy young volunteers (25 males and 25 females). The gambling task involved valence (loss and gain) and amount (50¢ and 10¢) as outcomes. The outcome-related negativity (ORN/N2) and outcome-related positivity (ORP/P3) were analyzed and compared across conditions and gender. Monetary gain (compared to loss) and higher amount (50¢ compared to 10¢) produced higher amplitudes and shorter latencies in both ORN and ORP components. Difference wave plots showed that earlier processing (200-400 ms) is dominated by the valence (loss/gain) while later processing (after 400 ms) is marked by the amount (50¢/10¢). Functional mapping using Low Resolution Electromagnetic Tomography (LORETA) indicated that the ORN separated the loss against gain in both genders, while the ORP activity distinguished the 50¢ against 10¢ in males. This study further strengthens the view that separate brain processes/circuitry may mediate loss and gain. Although there were no gender differences in behavioral and impulsivity scores, ORN and ORP measures for different task conditions had significant correlations with behavioral scores. This gambling paradigm may potentially offer valuable indicators to study outcome processing and impulsivity in normals as well as in clinical populations. PMID:18775749

Dietary fibers from mushroom sclerotia: 3. In vitro fermentability using human fecal microflora.

PubMed

Wong, Ka-Hing; Wong, King-Yee; Kwan, Hoi-Shan; Cheung, Peter C K

2005-11-30

The in vitro fermentability of three novel dietary fibers (DFs) prepared from mushroom sclerotia, namely, Pleurotus tuber-regium, Polyporous rhinocerus, and Wolfiporia cocos, was investigated and compared with that of the cellulose control. All DF samples (0.5 g each) were fermented in vitro with a human fecal homogenate (10 mL) in a batch system (total volume, 50 mL) under strictly anaerobic conditions (using oxygen reducing enzyme and under argon atmosphere) at 37 degrees C for 24 h. All three novel sclerotial DFs exhibited notably higher dry matter disappearance (P. tuber-regium, 8.56%; P. rhinocerus, 13.5%; and W. cocos, 53.4%) and organic matter disappearance (P. tuber-regium, 9.82%; P. rhinocerus, 14.6%; and W. cocos, 57.4%) when compared with those of the cellulose control. Nevertheless, only the W. cocos DF was remarkably degraded to produce considerable amounts of total short chain fatty acids (SCFAs) (5.23 mmol/g DF on organic matter basis, with a relatively higher molar ratio of propionate) that lowered the pH of its nonfermented residue to a slightly acidic level (5.89). Variations on the in vitro fermentability among the three sclerotial DFs might mainly be attributed to their different amounts of interwoven hyphae present (different amounts of enzyme inaccessible cell wall components) as well as the possible different structural arrangement (linkage and degree of branching) of their beta-glucans.

Method for the enzymatic production of hydrogen

DOEpatents

Woodward, Jonathan; Mattingly, Susan M.

1999-01-01

The present invention is an enzymatic method for producing hydrogen comprising the steps of: a) forming a reaction mixture within a reaction vessel comprising a substrate capable of undergoing oxidation within a catabolic reaction, such as glucose, galactose, xylose, mannose, sucrose, lactose, cellulose, xylan and starch. The reaction mixture further comprises an amount of glucose dehydrogenase in an amount sufficient to catalyze the oxidation of the substrate, an amount of hydrogenase sufficient to catalyze an electron-requiring reaction wherein a stoichiometric yield of hydrogen is produced, an amount of pH buffer in an amount sufficient to provide an environment that allows the hydrogenase and the glucose dehydrogenase to retain sufficient activity for the production of hydrogen to occur and also comprising an amount of nicotinamide adenine dinucleotide phosphate sufficient to transfer electrons from the catabolic reaction to the electron-requiring reaction; b) heating the reaction mixture at a temperature sufficient for glucose dehydrogenase and the hydrogenase to retain sufficient activity and sufficient for the production of hydrogen to occur, and heating for a period of time that continues until the hydrogen is no longer produced by the reaction mixture, wherein the catabolic reaction and the electron-requiring reactions have rates of reaction dependent upon the temperature; and c) detecting the hydrogen produced from the reaction mixture.

Method for the enzymatic production of hydrogen

DOEpatents

Woodward, J.; Mattingly, S.M.

1999-08-24

The present invention is an enzymatic method for producing hydrogen comprising the steps of: (a) forming a reaction mixture within a reaction vessel comprising a substrate capable of undergoing oxidation within a catabolic reaction, such as glucose, galactose, xylose, mannose, sucrose, lactose, cellulose, xylan and starch; the reaction mixture also comprising an amount of glucose dehydrogenase in an amount sufficient to catalyze the oxidation of the substrate, an amount of hydrogenase sufficient to catalyze an electron-requiring reaction wherein a stoichiometric yield of hydrogen is produced, an amount of pH buffer in an amount sufficient to provide an environment that allows the hydrogenase and the glucose dehydrogenase to retain sufficient activity for the production of hydrogen to occur and also comprising an amount of nicotinamide adenine dinucleotide phosphate sufficient to transfer electrons from the catabolic reaction to the electron-requiring reaction; (b) heating the reaction mixture at a temperature sufficient for glucose dehydrogenase and the hydrogenase to retain sufficient activity and sufficient for the production of hydrogen to occur, and heating for a period of time that continues until the hydrogen is no longer produced by the reaction mixture, wherein the catabolic reaction and the electron-requiring reactions have rates of reaction dependent upon the temperature; and (c) detecting the hydrogen produced from the reaction mixture. 8 figs.

Spatial Distribution and Site-Specific Spraying of Main Sucking Pests of Elm Trees.

PubMed

Karimzadeh, R; Iranipour, S

2017-06-01

Elm trees are important landscape trees and sucking insects weaken the elm trees and produce large amounts of honeydew. The main objectives of this study were to identify main honeydew-producing pests of elm trees and do site-specific spraying against these pests. To map the spatial distribution of the sucking pests in the large scale, the study area was divided into 40 × 40 m grids and one tree was chosen randomly from each grid (a total of 55 trees). These trees were sampled twice a year in 2011 and 2012. Each sample was a 30-cm branch terminal. Eight samples were taken from each tree in four cardinal directions and two canopy levels. The number of sucking insects and leaves of each sample were counted and recorded. Spatial analysis of the data was carried out using geostatistics. Kriging was used for producing prediction maps. Insecticide application was restricted to the regions with populations higher than threshold. To identify within-tree distribution of the honeydew-producing pests, six and four elm trees were chosen in 2011 and 2012 respectively, and sampled weekly. These trees were sampled as described previously. European elm scale (EES), Gossyparia spuria (Modeer) and two species of aphids were the dominant honeydew-producing pests. The results revealed that the effects of direction, canopy level and their interactions on insect populations were not statistically significant (P < 0.05). Site-specific spraying decreased the amount of insecticides used by ca. 20%, while satisfactory control of the sucking pests and honeydew excretion was obtained. Considering the environmental and economic benefits of site-specific spraying, it is worth doing more complementary works in this area.

Phototrophic hydrogen production from a clostridial [FeFe] hydrogenase expressed in the heterocysts of the cyanobacterium Nostoc PCC 7120.

PubMed

Avilan, Luisana; Roumezi, Baptiste; Risoul, Véronique; Bernard, Christophe Sébastien; Kpebe, Arlette; Belhadjhassine, Mayssène; Rousset, Marc; Brugna, Myriam; Latifi, Amel

2018-04-24

The conversion of solar energy into hydrogen represents a highly attractive strategy for the production of renewable energies. Photosynthetic microorganisms have the ability to produce H 2 from sunlight but several obstacles must be overcome before obtaining a sustainable and efficient H 2 production system. Cyanobacteria harbor [NiFe] hydrogenases required for the consumption of H 2 . As a result, their H 2 production rates are low, which makes them not suitable for a high yield production. On the other hand, [FeFe] enzymes originating from anaerobic organisms such as Clostridium exhibit much higher H 2 production activities, but their sensitivity to O 2 inhibition impairs their use in photosynthetic organisms. To reach such a goal, it is therefore important to protect the hydrogenase from O 2 . The diazotrophic filamentous cyanobacteria protect their nitrogenases from O 2 by differentiating micro-oxic cells called heterocysts. Producing [FeFe] hydrogenase in the heterocyst is an attractive strategy to take advantage of their potential in a photosynthetic microorganism. Here, we present a biological engineering approach for producing an active [FeFe] hydrogenase (HydA) from Clostridium acetobutylicum in the heterocysts of the filamentous cyanobacterium Nostoc PCC7120. To further decrease the O 2 amount inside the heterocyst, the GlbN cyanoglobin from Nostoc commune was coproduced with HydA in the heterocyst. The engineered strain produced 400 μmol-H 2 per mg Chlorophyll a, which represents 20-fold the amount produced by the wild type strain. This result is a clear demonstration that it is possible to associate oxygenic photosynthesis with H 2 production by an O 2 -sensitive hydrogenase.

A simple thick target for production of 89Zr using an 11MeV cyclotron

DOE Office of Scientific and Technical Information (OSTI.GOV)

Link, Jeanne M.; Krohn, Kenneth A.; O'Hara, Matthew J.

2017-04-01

The growing interest but limited availability of 89Zr for PET led us to test targets for the 89(p,n) reaction. The goal was an easily constructed target for an 11 MeV Siements cyclotron. Yttrium foils were tested at different thicknesses, angles and currents. A 90 degree foil tolerated 41 microAmp without damage and produced ~800 MBq/hr, >20 mCi, an amount adequate for radiochemistry research and human doses in a widely available accelerator. This method should translate to higher energy cyclotrons.

Final Technical Report: Increasing Prediction Accuracy.

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, Bruce Hardison; Hansen, Clifford; Stein, Joshua

2015-12-01

PV performance models are used to quantify the value of PV plants in a given location. They combine the performance characteristics of the system, the measured or predicted irradiance and weather at a site, and the system configuration and design into a prediction of the amount of energy that will be produced by a PV system. These predictions must be as accurate as possible in order for finance charges to be minimized. Higher accuracy equals lower project risk. The Increasing Prediction Accuracy project at Sandia focuses on quantifying and reducing uncertainties in PV system performance models.

A series of BCN nanosheets with enhanced photoelectrochemical performances

NASA Astrophysics Data System (ADS)

Li, Junqi; Lei, Nan; Hao, Hongjuan; Zhou, Jian

2017-03-01

A series of flake-like BCN compounds were produced by calcination at different reaction temperatures via thermal substitution of C atoms with B atoms of boric acid substructures in graphitic carbon nitrides (g-C3N4). The structural and optical properties of the samples were characterized by XRD, TEM, HRTEM, XPS and UV-vis absorption. The photoelectrochemical (PEC) performance of all samples were characterized through photocurrent and electrochemical impedance spectroscopy (EIS) measurement. The test results demonstrated that BCN nanosheets exhibited higher PEC performance with increasing substituted amount of boron.

Enhanced hot-electron production and strong-shock generation in hydrogen-rich ablators for shock ignition

DOE PAGES

Theobald, W.; Bose, A.; Yan, R.; ...

2017-12-08

Experiments were performed with CH, Be, C, and SiO 2 ablators interacting with high-intensity UV laser radiation (5 × 10 15 W/cm 2, λ = 351 nm) to determine the optimum material for hot-electron production and strong-shock generation. Significantly more hot electrons are produced in CH (up to ~13% instantaneous conversion efficiency), while the amount is a factor of ~2 to 3 lower in the other ablators. A larger hot-electron fraction is correlated with a higher effective ablation pressure. As a result, the higher conversion efficiency in CH is attributed to stronger damping of ion-acoustic waves because of the presencemore » of light H ions.« less

Enhanced hot-electron production and strong-shock generation in hydrogen-rich ablators for shock ignition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Theobald, W.; Bose, A.; Yan, R.

Experiments were performed with CH, Be, C, and SiO 2 ablators interacting with high-intensity UV laser radiation (5 × 10 15 W/cm 2, λ = 351 nm) to determine the optimum material for hot-electron production and strong-shock generation. Significantly more hot electrons are produced in CH (up to ~13% instantaneous conversion efficiency), while the amount is a factor of ~2 to 3 lower in the other ablators. A larger hot-electron fraction is correlated with a higher effective ablation pressure. As a result, the higher conversion efficiency in CH is attributed to stronger damping of ion-acoustic waves because of the presencemore » of light H ions.« less

Diacyl, alkenyl, and alkyl ether phospholipids in ejaculated, in utero-, and in vitro-incubated porcine spermatozoa.

PubMed

Evans, R W; Weaver, D E; Clegg, E D

1980-02-01

The phospholipids of porcine spermatozoa were analyzed by a hydrolytic procedure directly after ejaculation, and after incubation for 120 min in vitro or in ligated uterine segments of females with induced estrus. Total phospholipid content of ejaculated sperm was 65.7 micro g lipid P per 10(9) sperm, of which 41% was alkyl ether and 23% was alkenyl ether glycerophospholipid. All of the ether phospholipids were choline and ethanolamine glycerophospholipids. In order of decreasing amount (% of total phospholipid), the phospholipids were choline and ethanolamine glycerophospholipids (49.9 and 28.2), sphingolipid (10.6), cardiolipin (5.5), phosphatidylinositol (2.3), phosphatidic acid (1.5), phosphatidylserine (1.2), and phosphatidylglycerol (0.8). Phosphorus-containing sphingolipid separated into two components during thin-layer chromatography. Sphingosine was the only long-chain base identified in either band. Major fatty acids in the band with lower R(f) were 16:0 (56%), 20:0 (23%), and 18:0 (11%) plus smaller amounts of 14:0, 18:1, and 22:0, while those in the band with higher R(f) were 14:0 (30%), 16:0 (45%), and 18:1 (12%) plus smaller amounts of 18:0, 20:0, and 22:0. Choline was the only water-soluble base present in the lower R(f) sphingomyelin while ethanolamine was prevalent in the higher R(f) component. Incubation of washed spermatozoa in Ca(2+)-free Ringer-fructose at 37 degrees C for 2 hr produced no significant change in the level of any of the phospholipids. Incubation of washed sperm in the uterus for 2 hr, in the presence of oviductal secretions, produced an increase in phosphatidylcholine from 7.2 to 10.2 micro g lipid P per 10(9) sperm.-Evans, R. W., D. E. Weaver, and E. D. Clegg. Diacyl, alkenyl, and alkyl ether phospholipids in ejaculated, in utero-, and in vitro-incubated porcine spermatozoa.

Process for reproducibly preparing titanium subhydride

DOEpatents

Carlson, Richard S.

1982-01-01

Titanium subhydride is produced in a reactor by heating a selected amount of finely divided titanium compound at a selected temperature for a selected period of time under dynamic vacuum conditions. Hydrogen is removed substantially uniformly from each powder grain and there is produced a subhydride of substantially uniform titanium-hydrogen composition. Selection of the amount, temperature and time produces a subhydride of selected titanium-hydrogen composition.

Water reclamation during drinking water treatments using polyamide nanofiltration membranes on a pilot scale.

PubMed

Kukučka, Miroslav; Kukučka, Nikoleta; Habuda-Stanić, Mirna

2016-09-01

The aim of this study was to investigate the performances of polyamide nanofiltration membranes during water reclamation. The study was conducted using nanofiltration concentrates obtained from two different nanofiltration drinking water treatment plants placed in the northern part of Serbia (Kikinda and Zrenjanin). Used nanofiltration concentrates contained high concentrations of arsenic (45 and 451 μg/L) and natural organic matter (43.1 and 224.40 mgKMnO4/L). Performances of polyamide nanofiltration membranes during water reclamation were investigated under various fluxes and transmembrane pressures in order to obtain drinking water from nanofiltration concentrates and, therefore, reduce the amount of produced concentrates and minimize the waste that has to be discharged in the environment. Applied polyamide nanofiltration membranes showed better removal efficiency during water reclamation when the concentrate with higher content of arsenic and natural organic matter was used while the obtained permeates were in accordance with European regulations. This study showed that total concentrate yield can be reduced to ~5 % of the optimum flux value, in both experiments. The obtained result for concentrate yield under the optimum flux presents considerable amount of reclaimed drinking water and valuable reduced quantity of produced wastewater.

Response of Leuconostoc strains against technological stress factors: Growth performance and volatile profiles.

PubMed

Cicotello, Joaquín; Wolf, Irma V; D'Angelo, Luisa; Guglielmotti, Daniela M; Quiberoni, Andrea; Suárez, Viviana B

2018-08-01

The ability of twelve strains belonging to three Leuconostoc species (Leuconostoc mesenteroides, Leuconostoc lactis and Leuconostoc pseudomesenteroides) to grow under diverse sub-lethal technological stress conditions (cold, acidic, alkaline and osmotic) was evaluated in MRS broth. Two strains, Leuconostoc lactis Ln N6 and Leuconostoc mesenteroides Ln MB7, were selected based on their growth under sub-lethal conditions, and volatile profiles in RSM (reconstituted skim milk) at optimal and under stress conditions were analyzed. Growth rates under sub-lethal conditions were strain- and not species-dependent. Volatilomes obtained from the two strains studied were rather diverse. Particularly, Ln N6 (Ln. lactis) produced more ethanol and acetic acid than Ln MB7 (Ln. mesenteroides) and higher amounts and diversity of the rest of volatile compounds as well, at all times of incubation. For the two strains studied, most of stress conditions applied diminished the amounts of ethanol and acetic acid produced and the diversity and levels of the rest of volatile compounds. These results were consequence of the different capacity of the strains to grow under each stress condition tested. Copyright © 2018 Elsevier Ltd. All rights reserved.

Weldability of Aluminium Alloys for Automotive Applications

NASA Astrophysics Data System (ADS)

Löveborn, D.; Larsson, J. K.; Persson, K.-A.

Restrictions in CO2-emissions have caused increased demands on decreased weight and increased use of lightweight materials in the automotive industry. Aluminium has shown to be of great interest due to its beneficial weight to strength ratio, and are suitable for hang-on parts such as roof, doors etc. However, the use of aluminium requires reliable joining techniques. This project has been focusing on laser welding of aluminium. It have been reported earlier that hot cracks and porosity are common defects while joining aluminium with laser welding. The aim with this project has been to produce crack free laser welds while joining thin aluminium sheets. Two different optics have been used in this project, oscillating- and triple-spot optics. The results from the experiments show that both the oscillating optics and the triple-spot optics can produce crack free welds. The amount of pores is shown to be low for both cases. The results do also show that the amount of pores in the welds increases with the weld length while the flange length is of minor impact. The mechanical properties are similar for the both optics. The oscillation specimens receive a higher tensile strength while the triple-spot specimens receive a larger elongation at break value.

Core-shell AgSiO2-protoporphyrin IX nanoparticle: Effect of the Ag core on reactive oxygen species generation

NASA Astrophysics Data System (ADS)

Lismont, M.; Pá; ez-Martinez, C.; Dreesen, L.

2015-03-01

Photodynamic therapy (PDT) for cancer is based on the use of a light sensitive molecule to produce, under specific irradiation, toxic reactive oxygen species (ROS). A way to improve the therapy efficiency is to increase the amount of produced ROS near cancer cells. This aim can be achieved by using a metal enhanced process arising when an optically active molecule is located near a metallic nanoparticle (NP). Here, the coupling effect between silver (Ag) NPs and protoporphyrin IX (PpIX) molecules, a clinically approved photosensitizer, is studied compared first, to PpIX fluorescence yield and second, to ROS production efficiency. By applying a modified Stöber process, PpIX was encapsulated into a silica (SiO2) shell, surrounding a 60 nm sized Ag core. We showed that, compared to SiO2-PpIX NPs, Ag coated SiO2-PpIX NPs dramatically decreased PpIX fluorescence together with singlet oxygen production efficiency. However, after incubation time in the dark, the amount of superoxide anions generated by the Ag doped sample was higher than the control sample one.

Topical beta-carotene protects against infra-red-light-induced free radicals.

PubMed

Darvin, Maxim E; Fluhr, Joachim W; Meinke, Martina C; Zastrow, Leonhard; Sterry, Wolfram; Lademann, Juergen

2011-02-01

The influence of stress factors on human skin induces the production of free radicals. Free radicals react immediately with antioxidants contained in the skin, giving rise to their depletion and with the surrounding molecules, resulting in their damage, disorganization and even destruction. High amounts of free radicals are produced in the upper skin layers, i.e. mainly in the epidermis, subsequent to sun irradiation. Irradiation of the skin in the infra-red (IR) range of the spectra, applied at physiological doses, can produce free radicals. The magnitude of destruction of antioxidants, such as carotenoids, can serve as a marker of the extent of the stress factor, characterized by the quantity of produced free radicals. In this study, measurements on the degradation of cutaneous carotenoids following IR skin irradiation of 12 healthy volunteers (skin type II), with two IR sources (standard infrared radiator = SIR and water filter infrared = wIRA) were taken using resonance Raman spectroscopy. Topical application of the antioxidant beta-carotene (2 mg/cm(2) ) provided protection for the human skin when exposed to IR radiation. The magnitude of the degradation of dermal carotenoids after IR irradiation was significantly higher for SIR than for wIRA irradiation, for both non-treated and cream-treated skin areas. The amount of destroyed carotenoids after IR irradiation was higher in the case of pretreatment with beta-carotene than for the untreated skin, indicating that the superficial part of antioxidants is most important for protecting against external stressors. The direct comparison of beta-carotene content was significantly higher for the cream-treated compared to untreated areas for all pairs: baseline, wIRA, after wIRA, baseline SIR and after SIR. Additionally, topically applied carotenoids as a single antioxidant component are less stable than the carotenoids in the skin incorporated by nutrition and accumulated in a mixture with different antioxidant substances. Resonance Raman spectroscopy can be used for the non-invasive measurements of carotenoids, which can be rated as marker substances of redox processes. © 2011 John Wiley & Sons A/S.

Alternate propellant program, phase 1

NASA Technical Reports Server (NTRS)

Anderson, F. A.; West, W. R.

1979-01-01

Candidate propellant systems for the shuttle booster solid rocket motor (SRM), which would eliminate, or greatly reduce, the amount of HCl produced in the exhaust of the shuttle SRM were investigated. Ammonium nitrate was selected for consideration as the main oxidizer, with ammonium perchlorate and the nitramine, cyclo-tetramethylene-tetranitramine as secondary oxidizers. The amount of ammonium perchlorate used was limited to an amount which would produce an exhaust containing no more than 3% HCl.

Risk with energy from conventional and nonconventional sources.

PubMed

Inhaber, H

1979-02-23

Risk to human health was compared for five conventional and six nonconventional energy systems. The entire cycle for producing energy was considered, not just part. The most important conclusion drawn is that the risk to human health from nonconventional sources can be as high as, or even higher than, that of conventional sources. This result is produced only when the risk per unit energy is considered, rather than the risk per solar panel or windmill. The risk from nonconventional energy sources derives from the large amount of material and labor needed, along with their backup and storage requirements. Risk evaluation is a relatively new discipline, and therefore the results presented here can be considered only a beginning. However, society should keep relative risk in mind when evaluating present and future energy sources.

Formation of atomically smooth epitaxial metal films on a chemically reactive interface: Mg on Si(111)

NASA Astrophysics Data System (ADS)

Özer, Mustafa M.; Weitering, Hanno H.

2013-07-01

Deposition of Mg on Si(111)7 × 7 produces an epitaxial magnesium silicide layer. Under identical annealing conditions, the thickness of this Mg2Si(111) layer increases with deposition amount, reaching a maximum of 4 monolayer (ML) and decreasing to ˜3 ML at higher Mg coverage. Excess Mg coalesces into atomically flat, crystalline Mg(0001) films. This surprising growth mode can be attributed to the accidental commensurability of the Mg(0001), Si(111), and Mg2Si(111) interlayer spacing and the concurrent minimization of in-plane Si mass transfer and domain-wall energies. The commensurability of the interlayer spacing defines a highly unique solid-phase epitaxial growth process capable of producing trilayer structures with atomically abrupt interfaces and atomically smooth surface morphologies.

Digestive kinetics determines bioavailability of pollutants. Final report, 1 June 1993--30 September 1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jumars, P.A.; Mayer, L.M.

1999-04-19

The authors assayed digestive capabilities of marine deposit feeders (animals that eat sediments) by using fluorescently tagged substrates and contact-angle measurements of surfactancy. Polychaetes on average showed higher enzyme activities and surfactancy than echinoderms. They found that surfactants produced by deposit feeders substantially enhance their abilities to solubilize hydrophobic pollutants such as polycyclic aromatic hydrocarbons (PAHs). Amounts solubilized were consistent with incorporation into micelles of the surfactant. Kinetics of PAH uptake could be explained by passive diffusion. The authors also found that the digestive strategies of deposit feeders often produce concentrations of proteins (digestive enzymes plus products of protein digestion)more » that are sufficient to solubilize metals. Histidine residues in these proteins were found to be critical for copper binding.« less

Heterosis Increases Fertility, Fecundity, and Survival of Laboratory-Produced F1 Hybrid Males of the Malaria Mosquito Anopheles coluzzii

PubMed Central

Ekechukwu, Nkiru E.; Baeshen, Rowida; Traorè, Sékou F.; Coulibaly, Mamadou; Diabate, Abdoulaye; Catteruccia, Flaminia; Tripet, Frédéric

2015-01-01

The success of vector control strategies aiming to decrease disease transmission via the release of sterile or genetically-modified male mosquitoes critically depends on mating between laboratory-reared males and wild females. Unfortunately, mosquito colonization, laboratory rearing, and genetic manipulations can all negatively affect male competitiveness. Heterosis is commonly used to produce domestic animals with enhanced vigor and homogenous genetic background and could therefore potentially improve the mating performance of mass-reared male mosquitoes. Here, we produced enhanced hybrid males of the malaria mosquito Anopheles coluzzii by crossing two strains colonized >35 and 8 years ago. We compared the amount of sperm and mating plug proteins they transferred to females, as well as their insemination rate, reproductive success and longevity under various experimental conditions. Across experiments, widespread adaptations to laboratory mating were detected in the older strain. In large-group mating experiments, no overall hybrid advantage in insemination rates and the amount of sperm and accessory gland proteins transferred to females was detected. Despite higher sperm activity, hybrid males did not appear more fecund. However, individual-male mating and laboratory-swarm experiments revealed that hybrid males, while inseminating fewer females than older inbred males, were significantly more fertile, producing larger mating plugs and drastically increasing female fecundity. Heterotic males also showed increased longevity. These results validate the use of heterosis for creating hybrid males with improved fitness from long-established inbred laboratory strains. Therefore, this simple approach could facilitate disease control strategies based on male mosquito releases with important ultimate benefits to human health. PMID:26497140

Cornmeal and starch influence the dynamic of fumonisin B, A and C production and masking in Fusarium verticillioides and F. proliferatum.

PubMed

Lazzaro, Irene; Falavigna, Claudia; Galaverna, Gianni; Dall'Asta, Chiara; Battilani, Paola

2013-08-16

Fusarium verticillioides and F. proliferatum can infect maize ears and produce fumonisins. The fumonisin B (FB) series is the most prolifically produced, followed by fumonisin C (FC), A (FA) and P (FP); moreover hidden forms of fumonisins have been detected in maize and derivatives. There is a lack of information about which maize component may affect fumonisin pattern production. Therefore, in this work we studied the role of cornmeal and corn starch, as the sole source of nutrition, in the production dynamic of all fumonisin series, hidden forms included, in different strains of F. verticillioides and F. proliferatum incubated at 25°C for 7-45days. Both Fusarium species produced high amounts of FB, following the chemotype FB1>FB2>FB3; FC and FA were produced in lesser amounts, showing the chemotypes: FA2+FA3>FA1 and FC1>FC2+FC3>FC4, respectively; while no FP were detected. F. verticillioides was more prolific than F. proliferatum in fumonisin production (ten times more on average) in all the tested conditions. Fumonisin production was higher in cornmeal than in starch based medium in both Fusarium species; FA and FC were detected only in the former medium. An important role of amylopectin as an inducing factor for fumonisin biosynthesis was suggested, as were acid pH conditions. Fumonisin hidden forms may occur in cornmeal medium, whereas they were never found at significant levels in corn starch medium. Copyright © 2013 Elsevier B.V. All rights reserved.

Optimization of optical and mechanical properties of real architecture for 3-dimensional tissue equivalents: Towards treatment of limbal epithelial stem cell deficiency

PubMed Central

Massie, Isobel; Kureshi, Alvena K.; Schrader, Stefan; Shortt, Alex J.; Daniels, Julie T.

2015-01-01

Limbal epithelial stem cell (LESC) deficiency can cause blindness. Transplantation of cultured human limbal epithelial cells (hLE) on human amniotic membrane (HAM) can restore vision but clinical graft manufacture can be unreliable. We have developed a reliable and robust tissue equivalent (TE) alternative to HAM, Real Architecture for 3D Tissue (RAFT). Here, we aimed to optimize the optical and mechanical properties of RAFT TE for treatment of LESC deficiency in clinical application. The RAFT TE protocol is tunable; varying collagen concentration and volume produces differing RAFT TEs. These were compared with HAM samples taken from locations proximal and distal to the placental disc. Outcomes assessed were transparency, thickness, light transmission, tensile strength, ease of handling, degradation rates and suitability as substrate for hLE culture. Proximal HAM samples were thicker and stronger with poorer optical properties than distal HAM samples. RAFT TEs produced using higher amounts of collagen were thicker and stronger with poorer optical properties than those produced using lower amounts of collagen. The ‘optimal’ RAFT TE was thin, transparent but still handleable and was produced using 0.6 ml of 3 mg/ml collagen. Degradation rates of the ‘optimal’ RAFT TE and HAM were similar. hLE achieved confluency on ‘optimal’ RAFT TEs at comparable rates to HAM and cells expressed high levels of putative stem cell marker p63α. These findings support the use of RAFT TE for hLE transplantation towards treatment of LESC deficiency. PMID:26092352

Application of a set of complementary techniques to understand how varying the proportion of two wastes affects humic acids produced by vermicomposting.

PubMed

Fernández-Gómez, Manuel J; Nogales, Rogelio; Plante, Alain; Plaza, César; Fernández, José M

2015-01-01

A better understanding of how varying the proportion of different organic wastes affects humic acid (HA) formation during vermicomposting would be useful in producing vermicomposts enriched in HAs. With the aim of improving the knowledge about this issue, a variety of analytical techniques [UV-visible spectroscopic, Fourier transform infrared, fluorescence spectra, solid-state cross-polarization magic-angle spinning (CPMAS) (13)C nuclear magnetic resonance (NMR) spectra, and thermal analysis] was used in the present study to characterize HAs isolated from two mixtures at two different ratios (2:1 and 1:1) of tomato-plant debris (TD) and paper-mill sludge (PS) before and after vermicomposting. The results suggest that vermicomposting increased the HA content in the TD/PS 2:1 and 1:1 mixtures (15.9% and 16.2%, respectively), but the vermicompost produced from the mixture with a higher amount of TD had a greater proportion (24%) of HAs. Both vermicomposting processes caused equal modifications in the humic precursors contained in the different mixtures of TD and PS, and consequently, the HAs in the vermicomposts produced from different waste mixtures exhibited analogous characteristics. Only the set of analytical techniques used in this research was able to detect differences between the HAs isolated from each type of vermicompost. In conclusion, varying the proportion of different wastes may have a stronger influence on the amount of HAs in vermicomposts than on the properties of HAs. Copyright © 2014 Elsevier Ltd. All rights reserved.

Impact of Saccharomyces cerevisiae strains on traditional sparkling wines production.

PubMed

Di Gianvito, Paola; Perpetuini, Giorgia; Tittarelli, Fabrizia; Schirone, Maria; Arfelli, Giuseppe; Piva, Andrea; Patrignani, Francesca; Lanciotti, Rosalba; Olivastri, Lino; Suzzi, Giovanna; Tofalo, Rosanna

2018-07-01

Sparkling wine fermentation is a challenge for yeasts due to the hostile conditions. A phenotype sought in starters is flocculation, because it reduces riddling time. For this reason, six flocculent Saccharomyces cerevisiae wine strains with different flocculation degree and autolytic activity and two commercial strains were tested for traditional sparkling wine production in a winery. Yeast viability, free aminoacids and high molecular weight nitrogen release and physico-chemical composition of sparkling wines were evaluated. Moreover, strains were tested for their aromatic potential. Obtained data revealed that flocculent yeasts presented oenological performances (in terms of fermentation rate, maximum pressure reached, free aminoacids - AAN and high molecular weight nitrogen - HMWN release) similar to the commercial strains. All considered strains were able to complete fermentation and viable cells of all strains were detected in all sparkling wines produced even after 6 months. F6789 and F10471 strains showed slow fermentation kinetics reaching the maximum of pressure at 180 days. Regarding nitrogen compounds release, FI strain was characterized by the highest amount of AAN and HMWN released, followed by F6789. Strains showed a considerable diversification in terms of number and amount of aroma molecules produced and sparkling wines obtained with autochthonous flocculent strains presented a higher amount of alcohols and esters already after 3 months. Further studies are necessary to select starter strains to improve traditional sparkling wines production. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effects on H(-) production in a multicusp ion source by mixture of H2 with H2O, NH3, CH4, N2H4, and SF6

NASA Technical Reports Server (NTRS)

Orient, O. J.; Chutjian, A.; Leung, K. N.

1987-01-01

Effects of H(-) production in a multicusp ion source are measured by separately mixing with hydrogen small amounts (0.33-10 percent) of water, ammonia, methane, and hydrazine these are molecules which produce large amounts of H(-) via dissociative attachment (DA) resonances at higher electron energies. The mixing was done in a separate reservoir, with careful measurement of individual pressures. Experimental enhancements of 1.4 and less were observed, whereas calculated enhancements, using accurate DA cross sections for ground-state H2, should have produced factors of 1.5, 3.0, 1.3, and 2.4 enhancements for water, ammonia methane, and hydrazine, respectively, at a mean electron energy of 1.0 eV in the extraction region. The difference is accounted for by including, in the enhancement calculation, vibrationally and rotationally excited H2 molecules, with v-double prime = 5-11, and J-double prime = 0-5, and the large DA cross sections for the excited H2 (v-double prime, J-double prime). The relative populations of H2 (v-double prime, J-double prime) thus obtained are found to be substantially smaller than those predicted by theoretical calculations. The effect on H(-) current was also studied by mixing small amounts of SF6 with H2. A 1.5 percent mixture was found to reduce the H(-) output by one half.

Effect of chitosan on the heat stability of whey protein solution as a function of pH.

PubMed

Zhao, Zhengtao; Xiao, Qian

2017-03-01

Chitosan was reported to interact with proteins through electrostatic interactions. Their interaction was influenced by pH, which was not fully characterized. Further research on the interactions between protein and chitosan at different pH and their influence on the thermal denaturation of proteins is necessary. In this research, the effect of chitosan on the heat stability of whey protein solution at pH 4.0-6.0 was studied. At pH 4.0, a small amount chitosan was able to prevent the heat-induced denaturation and aggregation of whey protein molecules. At higher pH values (5.5 and 6.0), whey proteins complexed with chitosan through electrostatic attraction. The formation of chitosan-whey protein complexes at pH 5.5 improved the heat stability of dispersions and no precipitation could be detected up to 20 days. The dispersion with a medium amount of chitosan (chitosan:whey protein 1:5) produced the most stable particles, which had an average radius of 135 ± 14 nm and a zeta potential value of 36 ± 1 mV. In contrast, at pH 6.0 only the dispersion with a high amount of chitosan (chitosan:whey protein 1:2) showed good shelf stability up to 20 days. It was possible to produce heat-stable whey protein beverages by regulating the interaction between chitosan and whey protein molecules. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Process and system for removing sulfur from sulfur-containing gaseous streams

DOEpatents

Basu, Arunabha; Meyer, Howard S.; Lynn, Scott; Leppin, Dennis; Wangerow, James R.

2012-08-14

A multi-stage UCSRP process and system for removal of sulfur from a gaseous stream in which the gaseous stream, which contains a first amount of H.sub.2S, is provided to a first stage UCSRP reactor vessel operating in an excess SO.sub.2 mode at a first amount of SO.sub.2, producing an effluent gas having a reduced amount of SO.sub.2, and in which the effluent gas is provided to a second stage UCSRP reactor vessel operating in an excess H.sub.2S mode, producing a product gas having an amount of H.sub.2S less than said first amount of H.sub.2S.

Mixtures of Sulfates in Melas Chasma

NASA Image and Video Library

2017-09-04

In this image from NASA's Mars Reconnaissance Orbiter, layering within the light-toned sulfate deposit is the result of different states of hydration. Some of the layers have sulfates with little water (known as monohydrated sulfates) whereas other layers have higher amounts of water (called polyhydrated sulfates). The different amounts of water within the sulfates may reflect changes in the water chemistry during deposition of the sulfates, or may have occurred after the sulfates were laid down when heat or pressure forced the water out of some layers, causing a decrease in the hydration state. Many locations on Mars have sulfates, which are sedimentary rocks formed in water. Within Valles Marineris, the large canyon system that cuts across the planet, there are big and thick sequences of sulfates. The CRISM instrument on MRO is crucial for telling scientists which type of sulfate is associated with each layer, because each hydration state will produce a spectrum with absorptions at specific wavelengths depending upon the amount of water contained within the sulfate. https://photojournal.jpl.nasa.gov/catalog/PIA21935

Heavy rainfall in Mediterranean cyclones. Part I: contribution of deep convection and warm conveyor belt

NASA Astrophysics Data System (ADS)

Flaounas, Emmanouil; Kotroni, Vassiliki; Lagouvardos, Konstantinos; Gray, Suzanne L.; Rysman, Jean-François; Claud, Chantal

2018-04-01

In this study, we provide an insight to the role of deep convection (DC) and the warm conveyor belt (WCB) as leading processes to Mediterranean cyclones' heavy rainfall. To this end, we use reanalysis data, lighting and satellite observations to quantify the relative contribution of DC and the WCB to cyclone rainfall, as well as to analyse the spatial and temporal variability of these processes with respect to the cyclone centre and life cycle. Results for the period 2005-2015 show that the relationship between cyclone rainfall and intensity has high variability and demonstrate that even intense cyclones may produce low rainfall amounts. However, when considering rainfall averages for cyclone intensity bins, a linear relationship was found. We focus on the 500 most intense tracked cyclones (responsible for about 40-50% of the total 11-year Mediterranean rainfall) and distinguish between the ones producing high and low rainfall amounts. DC and the WCB are found to be the main cause of rainfall for the former (producing up to 70% of cyclone rainfall), while, for the latter, DC and the WCB play a secondary role (producing up to 50% of rainfall). Further analysis showed that rainfall due to DC tends to occur close to the cyclones' centre and to their eastern sides, while the WCBs tend to produce rainfall towards the northeast. In fact, about 30% of rainfall produced by DC overlaps with rainfall produced by WCBs but this represents only about 8% of rainfall produced by WCBs. This suggests that a considerable percentage of DC is associated with embedded convection in WCBs. Finally, DC was found to be able to produce higher rain rates than WCBs, exceeding 50 mm in 3-h accumulated rainfall compared to a maximum of the order of 40 mm for WCBs. Our results demonstrate in a climatological framework the relationship between cyclone intensity and processes that lead to heavy rainfall, one of the most prominent environmental risks in the Mediterranean. Therefore, we set perspectives for a deeper analysis of the favourable atmospheric conditions that yield high impact weather.

Developing a mesophilic co-culture for direct conversion of cellulose to butanol in consolidated bioprocess.

PubMed

Wang, Zhenyu; Cao, Guangli; Zheng, Ju; Fu, Defeng; Song, Jinzhu; Zhang, Junzheng; Zhao, Lei; Yang, Qian

2015-01-01

Consolidated bioprocessing (CBP) of butanol production from cellulosic biomass is a promising strategy for cost saving compared to other processes featuring dedicated cellulase production. CBP requires microbial strains capable of hydrolyzing biomass with enzymes produced on its own with high rate and high conversion and simultaneously produce a desired product at high yield. However, current reported butanol-producing candidates are unable to utilize cellulose as a sole carbon source and energy source. Consequently, developing a co-culture system using different microorganisms by taking advantage of their specific metabolic capacities to produce butanol directly from cellulose in consolidated bioprocess is of great interest. This study was mainly undertaken to find complementary organisms to the butanol producer that allow simultaneous saccharification and fermentation of cellulose to butanol in their co-culture under mesophilic condition. Accordingly, a highly efficient and stable consortium N3 on cellulose degradation was first developed by multiple subcultures. Subsequently, the functional microorganisms with 16S rRNA sequences identical to the denaturing gradient gel electrophoresis (DGGE) profile were isolated from consortium N3. The isolate Clostridium celevecrescens N3-2 exhibited higher cellulose-degrading capability was thus chosen as the partner strain for butanol production with Clostridium acetobutylicum ATCC824. Meanwhile, the established stable consortium N3 was also investigated to produce butanol by co-culturing with C. acetobutylicum ATCC824. Butanol was produced from cellulose when C. acetobutylicum ATCC824 was co-cultured with either consortium N3 or C. celevecrescens N3-2. Co-culturing C. acetobutylicum ATCC824 with the stable consortium N3 resulted in a relatively higher butanol concentration, 3.73 g/L, and higher production yield, 0.145 g/g of glucose equivalent. The newly isolated microbial consortium N3 and strain C. celevecrescens N3-2 displayed effective degradation of cellulose and produced considerable amounts of butanol when they were co-cultured with C. acetobutylicum ATCC824. This is the first report of application of co-culture to produce butanol directly from cellulose under mesophilic condition. Our results indicated that co-culture of mesophilic cellulolytic microbe and butanol-producing clostridia provides a technically feasible and more simplified way for producing butanol directly from cellulose.

An Alkalophilic Bacillus sp. Produces 2-Phenylethylamine

PubMed Central

Hamasaki, Nobuko; Shirai, Shinji; Niitsu, Masaru; Kakinuma, Katsumi; Oshima, Tairo

1993-01-01

A large amount of 2-phenylethylamine was produced in cells of alkalophilic Bacillus sp. strain YN-2000. This amine is secreted in the medium during the cell growth. The amounts of 2-phenylethylamine in both cells and medium change upon changing the pH of the medium. PMID:16349025

26 CFR 1.993-4 - Definition of producer's loans.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 10 2014-04-01 2013-04-01 true Definition of producer's loans. 1.993-4 Section...'s research and experimental expenditures. The amount described in this subdivision is the aggregate amount, whether or not charged to capital account, of research and experimental expenditures (within the...

Variation in Chemical Defense Among Natural Populations of Common Toad, Bufo bufo, Tadpoles: the Role of Environmental Factors.

PubMed

Bókony, Veronika; Móricz, Ágnes M; Tóth, Zsófia; Gál, Zoltán; Kurali, Anikó; Mikó, Zsanett; Pásztor, Katalin; Szederkényi, Márk; Tóth, Zoltán; Ujszegi, János; Üveges, Bálint; Krüzselyi, Dániel; Capon, Robert J; Hoi, Herbert; Hettyey, Attila

2016-04-01

Defensive toxins are widespread in nature, yet we know little about how various environmental factors shape the evolution of chemical defense, especially in vertebrates. In this study we investigated the natural variation in the amount and composition of bufadienolide toxins, and the relative importance of ecological factors in predicting that variation, in larvae of the common toad, Bufo bufo, an amphibian that produces toxins de novo. We found that tadpoles' toxin content varied markedly among populations, and the number of compounds per tadpole also differed between two geographical regions. The most consistent predictor of toxicity was the strength of competition, indicating that tadpoles produced more compounds and larger amounts of toxins when coexisting with more competitors. Additionally, tadpoles tended to contain larger concentrations of bufadienolides in ponds that were less prone to desiccation, suggesting that the costs of toxin production can only be afforded by tadpoles that do not need to drastically speed up their development. Interestingly, this trade-off was not alleviated by higher food abundance, as periphyton biomass had negligible effect on chemical defense. Even more surprisingly, we found no evidence that higher predation risk enhances chemical defenses, suggesting that low predictability of predation risk and high mortality cost of low toxicity might select for constitutive expression of chemical defense irrespective of the actual level of predation risk. Our findings highlight that the variation in chemical defense may be influenced by environmental heterogeneity in both the need for, and constraints on, toxicity as predicted by optimal defense theory.

Seabird guano fertilizes Baltic Sea littoral food webs.

PubMed

Gagnon, Karine; Rothäusler, Eva; Syrjänen, Anneli; Yli-Renko, Maria; Jormalainen, Veijo

2013-01-01

Nutrient enrichment in coastal marine systems can have profound impacts on trophic networks. In the Baltic Sea, the population of Great Cormorant (Phalacrocorax carbo sinensis) has increased nearly exponentially since the mid-1990 s, and colonies of these seabirds can be important sources of nitrogen enrichment for nearby benthic communities due to guano runoff. In this study we used stable isotope analyses and diet mixing models to determine the extent of nitrogen enrichment from cormorant colonies, as well as to examine any possible changes in herbivore diet preferences due to enrichment. We found significantly higher levels of δ(15)N in samples from colony islands than control islands for producers (the dominant macroalga Fucus vesiculosus, filamentous algae, and periphyton) and herbivores, as well as a positive correlation between enrichment and nest density in colony sites. We also found that enrichment increased over the breeding season of the cormorants, with higher enrichment in late summer than early summer. While the amount of total nitrogen did not differ between colony and control sites, the amount of guano-based nitrogen in algae was >50% in most sites, indicating high nitrogen enrichment from colonies. Herbivores (the isopod Idotea balthica and the gastropod Theodoxus fluviatilis) preferred feeding upon the dominant macroalga Fucus vesiculosus rather than on filamentous algae or periphyton in both control and colony, and there was a significant increase in periphyton consumption near colony sites. Overall, guano from cormorant colonies seems to have effects on both producers and herbivores, as well as the potential to modify algae-herbivore interactions.

Seabird Guano Fertilizes Baltic Sea Littoral Food Webs

PubMed Central

Gagnon, Karine; Rothäusler, Eva; Syrjänen, Anneli; Yli-Renko, Maria; Jormalainen, Veijo

2013-01-01

Nutrient enrichment in coastal marine systems can have profound impacts on trophic networks. In the Baltic Sea, the population of Great Cormorant (Phalacrocorax carbo sinensis) has increased nearly exponentially since the mid-1990s, and colonies of these seabirds can be important sources of nitrogen enrichment for nearby benthic communities due to guano runoff. In this study we used stable isotope analyses and diet mixing models to determine the extent of nitrogen enrichment from cormorant colonies, as well as to examine any possible changes in herbivore diet preferences due to enrichment. We found significantly higher levels of δ15N in samples from colony islands than control islands for producers (the dominant macroalga Fucus vesiculosus, filamentous algae, and periphyton) and herbivores, as well as a positive correlation between enrichment and nest density in colony sites. We also found that enrichment increased over the breeding season of the cormorants, with higher enrichment in late summer than early summer. While the amount of total nitrogen did not differ between colony and control sites, the amount of guano-based nitrogen in algae was >50% in most sites, indicating high nitrogen enrichment from colonies. Herbivores (the isopod Idotea balthica and the gastropod Theodoxus fluviatilis) preferred feeding upon the dominant macroalga Fucus vesiculosus rather than on filamentous algae or periphyton in both control and colony, and there was a significant increase in periphyton consumption near colony sites. Overall, guano from cormorant colonies seems to have effects on both producers and herbivores, as well as the potential to modify algae-herbivore interactions. PMID:23593452

STUDIES ON THE AMOUNT OF LIGHT EMITTED BY MIXTURES OF CYPRIDINA LUCIFERIN AND LUCIFERASE

PubMed Central

Stevens, Kenneth P.

1927-01-01

1. A photometric method was devised for measuring the intensities of light emitted per cc. of hiciferin solution and calculating the amount of light emitted per gm. of dried Cypridina powder. A total of 128 runs was made and the data are incorporated in this report. 2. The maximum amount of light emitted from 1 gm. of powder under the experimental conditions was 0.655 lumens. Different samples of powder vary greatly in amount of light production. 3. When the concentration of substrate is doubled, nearly twice as much light is emitted, or an average ratio 2C/C of 1.86. Calculations of total light emissions per gm. of powder at different concentrations indicate that slightly more light is produced from the smaller concentrations. The maximum amount of light was produced by the solutions made with neutral sea water and averaged 0.445 lumens. The least light was obtained from solutions in distilled water saturated with hydrogen. The technique allows too rapid spontaneous oxidation prior to the saturation with hydrogen. The maximum amount of light from such experiments was only 0.077 lumens. Acid sea water solutions subsequently neutralized gave an average maximum of 0.386 lumens per gm. of powder per second. 4. When the concentration of enzyme is doubled, approximately the same amount of light is produced by both concentrations, although the stronger concentrations are slightly less effective than weaker ones. This undoubtedly is due to the colloidal nature of the enzyme and is a function of surface rather than of mass. In dilute solutions greater dispersion probably allows for greater adsorption to the surface of the enzyme. The average maximum amount of light produced in the series of enzyme experiments is of the magnitude 0.56 lumens per gm. of powder. PMID:19872366

Pluri-energy analysis of livestock systems--a comparison of dairy systems in different territories.

PubMed

Vigne, Mathieu; Vayssières, Jonathan; Lecomte, Philippe; Peyraud, Jean-Louis

2013-09-15

This paper introduces a generic assessment method called pluri-energy analysis. It aims to assess the types of energy used in agricultural systems and their conversion efficiencies. Four types of energy are considered: fossil energy, gross energy contained in the biomass, energy from human and animal labor and solar energy. The method was applied to compare smallholder low-input dairy-production systems, which are common in developing countries, to the high-input systems encountered in OECD countries. The pluri-energy method is useful for analyzing the functioning of agricultural systems by highlighting their modes of energy management. Since most dairy systems in South Mali (SM) are low-input systems, they are primarily based on solar and labor energy types and do not require substantial fossil-energy inputs to produce milk. Farms in Poitou-Charentes (PC) and Bretagne (BR) show intermediate values of fossil-energy use for milk production, similar to that found in the literature for typical European systems. However, fossil-energy use for milk production is higher on PC than BR farms because of a higher proportion of maize silage in the forage area; grazing pastures are more common on BR farms. Farms on Reunion Island (RI) require a relatively large amount of fossil energy to produce milk, mainly because the island context limits the amount of arable land. Consequently, milk production is based on large imports of concentrated feed with a high fossil-energy cost. The method also enables assessment of fossil-energy-use efficiency in order to increase the performance of biological processes in agricultural systems. Comparing the low-input systems represented by SM to the high-input systems represented by RI, PC and BR, an increase in solar-energy conversion, and thus land productivity, was observed due to intensification via increased fossil-energy use. Conversely, though fossil-energy use at the herd level increased milk productivity, its effect on gross-energy conversion by the herd was less evident. Partitioning the total on-farm gross energy produced among animal co-products (milk, meat and manure) highlights the major functions of SM herds, which are managed to produce organic crop fertilizers. Copyright © 2013 Elsevier Ltd. All rights reserved.

DDE in brown and white fat of hibernating bats

USGS Publications Warehouse

Clark, D.R.; Krynitsky, A.J.

1983-01-01

Samples of brown and white fat from hibernating bats (big brown bat, Eptesicus fuscus; little brown bat, Myotis lucifugus; and eastern pipistrelle, Pipistrellus subflavus) collected in western Maryland, USA, were analysed to determine lipid and DDE content. Amounts of brown fat, expressed as percentages of total bat weight, were the same for all three species. Lipid content of brown fat was significantly less than that of white fat. Lipids of brown fat contained significantly higher (28%) concentrations of DDE than did lipids of white fat. In our mixed-species sample of 14 bats, concentrations of DDE increased exponentially in both brown and white fat as white fat reserves declined. Brown fat facilitates arousal from hibernation by producing heat through rapid metabolism of triglycerides. The question is raised whether organochlorine residues, such as DDE, may be concentrated and then liberated in lethal amounts by the processes of hibernation and arousal.

Evaluation of a Hypocrea jecorina enzyme preparation for hydrolysis of Tifton 85 bermudagrass.

PubMed

Ximenes, E A; Brandon, S K; Doran-Peterson, J

2008-03-01

Tifton 85 bermudagrass, developed at the ARS-USDA in Tifton, GA, is grown on over ten million acres in the USA for hay and forage. Of the bermudagrass cultivars, Tifton 85 exhibits improved digestibility because the ratio of ether- to ester-linked phenolic acids has been lowered using traditional plant breeding techniques. A previously developed pressurized batch hot water (PBHW) method was used to treat Tifton 85 bermudagrass for enzymatic hydrolysis. Native grass (untreated) and PBHW-pretreated material were compared as substrates for fungal cultivation to produce enzymes. Cellulase activity, measured via the filter paper assay, was higher for fungi cultivated on PBHW-pretreated grass, whereas the other nine enzyme assays produced higher activities for the untreated grass. Ferulic acid and vanillin levels increased significantly for the enzyme preparations produced using PBHW-pretreated grass and the release of these phenolic compounds may have contributed to the observed reduction in enzyme activities. Culture supernatant from Tifton 85 bermudagrass-grown fungi were combined with two commercial enzyme preparations and the enzyme activity profiles are reported. The amount of reducing sugar liberated by the enzyme mixture from Hypocrea jecorina (after 192 h incubation with untreated bermudagrass) individually or in combination with feruloyl esterase was 72.1 and 84.8%, respectively, of the commercial cellulase preparation analyzed under the same conditions.

Evaluation of a Hypocrea jecorina Enzyme Preparation for Hydrolysis of Tifton 85 Bermudagrass

NASA Astrophysics Data System (ADS)

Ximenes, E. A.; Brandon, S. K.; Doran-Peterson, J.

Tifton 85 bermudagrass, developed at the ARS-USDA in Tifton, GA, is grown on over ten million acres in the USA for hay and forage. Of the bermudagrass cultivars, Tifton 85 exhibits improved digestibility because the ratio of ether- to ester-linked phenolic acids has been lowered using traditional plant breeding techniques. A previously developed pressurized batch hot water (PBHW) method was used to treat Tifton 85 bermudagrass for enzymatic hydrolysis. Native grass (untreated) and PBHW-pretreated material were compared as substrates for fungal cultivation to produce enzymes. Cellulase activity, measured via the filter paper assay, was higher for fungi cultivated on PBHW-pretreated grass, whereas the other nine enzyme assays produced higher activities for the untreated grass. Ferulic acid and vanillin levels increased significantly for the enzyme preparations produced using PBHW-pretreated grass and the release of these phenolic compounds may have contributed to the observed reduction in enzyme activities. Culture supernatant from Tifton 85 bermudagrass-grown fungi were combined with two commercial enzyme preparations and the enzyme activity profiles are reported. The amount of reducing sugar liberated by the enzyme mixture from Hypocrea jecorina (after 192 h incubation with untreated bermudagrass) individually or in combination with feruloyl esterase was 72.1 and 84.8%, respectively, of the commercial cellulase preparation analyzed under the same conditions.

Quality of maize for sale in markets in Benin and Niger.

PubMed

Bakoye, O N; Baoua, I B; Seyni, H; Amadou, L; Murdock, L L; Baributsa, D

2017-03-01

A follow-up study on the quality of maize for sale in West African public markets was carried out in Benin and Niger from August 15-28, 2013. Complementing the earlier study, this present assessment included not only retailers but also wholesalers and maize producers. Samples were evaluated for parameters related to the physical quality of the maize and for aflatoxin contamination. Most maize value chain actors process their offered grain using traditional methods for threshing, winnowing and drying. Maize for sale in the markets surveyed had an average moisture content ranging between 12 and 14%. Non-grain impurities amounted to 0-2.3% while mouldy grains ranged between 0.2 and 0.8%. The impurity level in grain was three times higher among wholesalers compared to retailers and producers. An insect pest, the Larger Grain Borer ( Prostephanus truncatus (Horn) was found only in Benin but Sitophilus zeamais Motschulsky, Cryptolestes ferrugineus Stephens, and Tribolium castaneum Herbst, were present in maize for sale in the markets in of both countries. Insect pest frequency was 16 times higher in wholesalers' grain compared to that of retailers and producers. Aflatoxin levels exceeding the accepted standard of 20 ppb were noted in markets in both countries. The highest proportion of aflatoxin-contaminated maize was in wholesalers' grain in Malanville market.

Mutants of Saccharomyces cerevisiae and Bacillus citri Changed the Protein Content of the Nigerian Oryza sativa variety “Igbimo” during Fermentation

PubMed Central

Boboye, Bolatito E; Adeleke, Mutiat A; Olawale, Anthony O

2012-01-01

Effect of mutation on protein production by Saccharomyces cerevisiae and Bacillus citri, the best protein producing yeast and bacterium isolated during a previous natural fermentation of a Nigerian rice (“Igbimo”). The two microorganisms were grown to logarithmic phase and mutagenized separately using ethylmethyl sulphonate (EMS). The wild-types and variants were inoculated individually into sterile “Igbimo” rice. Fermentation was allowed to take place at 27°C for 7 days after which protein released into the rice was quantified using the Biuret reagent method. The data obtained showed that the mutants are different from each other. Some mutants did form the protein at lower concentrations, others at the same and higher concentrations than the mother strains. The parental strains of S. cerevisiae and B. citri synthesized 0.89 mg/mL and 0.36 mg/mL protein respectively. Four groups of the mutants are recognized: classes I, II, III and IV which are the Poor, Average, Good and Super Protein Producers with 0-0.20, 0.21-0.50, 0.51-1.0 and 1.0 mg/mL protein respectively The yeast mutants produced higher amounts of protein than those of the bacterium. PMID:23166568

Comparison of friction produced by two types of orthodontic bracket protectors

PubMed Central

Mendonça, Steyner de Lima; Praxedes Neto, Otávio José; de Oliveira, Patricia Teixeira; dos Santos, Patricia Bittencourt Dutra; Pinheiro, Fábio Henrique de Sá Leitão

2014-01-01

Introduction Fixed orthodontic appliances have been regarded as a common causative factor of oral lesions. To manage soft tissue discomfort, most orthodontists recommend using a small amount of utility wax over the brackets in order to alleviate trauma. This in vitro study aimed at evaluating friction generated by two types of bracket protectors (customized acetate protector [CAP] and temporary resin protector [TRP]) during the initial stages of orthodontic treatment. Methods An experimental model (test unit) was used to assess friction. In order to measure the friction produced in each test, the model was attached to a mechanical testing machine which simulated maxillary canines alignment. Intergroup comparison was carried out by one-way ANOVA with level of significance set at 5%. Results The friction presented by the TRP group was statistically higher than that of the control group at 6 mm. It was also higher than in the control and CAP groups in terms of maximum friction. Conclusion The customized acetate protector (CAP) demonstrated not to interfere in friction between the wire and the orthodontic bracket slot. PMID:24713564

Comparison of friction produced by two types of orthodontic bracket protectors.

PubMed

de Lima Mendonça, Steyner; Praxedes Neto, Otávio José; de Oliveira, Patricia Teixeira; dos Santos, Patricia Bittencourt Dutra; de Sá Leitão Pinheiro, Fábio Henrique

2014-01-01

Fixed orthodontic appliances have been regarded as a common causative factor of oral lesions. To manage soft tissue discomfort, most orthodontists recommend using a small amount of utility wax over the brackets in order to alleviate trauma. This in vitro study aimed at evaluating friction generated by two types of bracket protectors (customized acetate protector [CAP] and temporary resin protector [TRP]) during the initial stages of orthodontic treatment. An experimental model (test unit) was used to assess friction. In order to measure the friction produced in each test, the model was attached to a mechanical testing machine which simulated maxillary canines alignment. Intergroup comparison was carried out by one-way ANOVA with level of significance set at 5%. The friction presented by the TRP group was statistically higher than that of the control group at 6 mm. It was also higher than in the control and CAP groups in terms of maximum friction. The customized acetate protector (CAP) demonstrated not to interfere in friction between the wire and the orthodontic bracket slot.

Type and amount of organic amendments affect enhanced biogenic methane production from coal and microbial community structure

USGS Publications Warehouse

Davis, Katherine J.; Lu, Shipeng; Barnhart, Elliott P.; Parker, Albert E.; Fields, Matthew W.; Gerlach, Robin

2018-01-01

Slow rates of coal-to-methane conversion limit biogenic methane production from coalbeds. This study demonstrates that rates of coal-to-methane conversion can be increased by the addition of small amounts of organic amendments. Algae, cyanobacteria, yeast cells, and granulated yeast extract were tested at two concentrations (0.1 and 0.5 g/L), and similar increases in total methane produced and methane production rates were observed for all amendments at a given concentration. In 0.1 g/L amended systems, the amount of carbon converted to methane minus the amount produced in coal only systems exceeded the amount of carbon added in the form of amendment, suggesting enhanced coal-to-methane conversion through amendment addition. The amount of methane produced in the 0.5 g/L amended systems did not exceed the amount of carbon added. While the archaeal communities did not vary significantly, the bacterial populations appeared to be strongly influenced by the presence of coal when 0.1 g/L of amendment was added; at an amendment concentration of 0.5 g/L the bacterial community composition appeared to be affected most strongly by the amendment type. Overall, the results suggest that small amounts of amendment are not only sufficient but possibly advantageous if faster in situcoal-to-methane production is to be promoted.

Production of three symbiosis-related fatty acids by Symbiodinium types in clades A-F associated with marine invertebrate larvae

NASA Astrophysics Data System (ADS)

Mies, M.; Chaves-Filho, A. B.; Miyamoto, S.; Güth, A. Z.; Tenório, A. A.; Castro, C. B.; Pires, D. O.; Calderon, E. N.; Sumida, P. Y. G.

2017-12-01

Symbiodinium are dinoflagellates engaged in a mutualistic symbiosis with multiple coral reef taxa. They are divided in nine different clades (A-I), which typically associate with different hosts. However, very little information is available on metabolic differences in Symbiodinium types, especially when associated with metazoan larvae. We tested whether three ω3 fatty acids (stearidonic acid, SDA; docosapentaenoic acid, DPA; and docosahexaenoic acid, DHA) that are typically translocated from Symbiodinium to its host are produced by Symbiodinium types within clades A-F associated with Mussismilia hispida (scleractinian coral), Berghia stephanieae (nudibranch), and Tridacna crocea (giant clam) larvae. We acquired and spawned broodstock for each host, cultured their larvae, and offered Symbiodinium types belonging to clades A-F. Samples were taken during a 72-h window after the offer of Symbiodinium, and fatty acids were extracted and analyzed by gas chromatography. The concentrations of SDA and DPA for all host larvae-dinoflagellate associations were low and variable, without trends. However, M. hispida planula larvae associated with Symbiodinium A1 and C1 had a statistically significant higher amount of DHA. The veliger larvae of B. stephanieae digested the Symbiodinium, and the amount of DHA remained constant throughout the experiment. The veliger larvae of T. crocea associated with Symbiodinium A1 and C1 also presented a higher amount of DHA, although not statistically different from the other types. These results show that Symbiodinium A1 and C1, in the case of M. hispida and T. crocea (which usually harbor strains within clades A and C), may contribute a small amount of DHA to the larvae of these organisms and form a stronger mutualism than other strains.

Antigen-specific IL-23/17 pathway activation by murine semi-mature DC-like cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nagasaka, Shinya; Iwasaki, Takumi; Okano, Tomoko

We analyzed the phenotype and function of bone marrow-derived dendritic cells (DCs) induced in vitro without using any serum during the late stage of cultivation. These 'serum-free' DCs (SF-DCs) possessed the ability to induce T cell proliferation as well as antibody responses, indicating that they were functional DCs. Surprisingly, the SF-DCs akin to semi-mature DCs in terms of both phenotypic and functional characteristics. The SF-DCs did not produce IL-12 but produced large amounts of IL-23 following lipopolysaccharide stimulation. The antigen-specific production of IL-17 by CD4{sup +} T cells co-cultured with OVA-loaded SF-DCs was significantly higher than that with OVA-loaded conventionalmore » DCs. These results suggest that SF-DCs tend to produce IL-23 and can consequently induce the IL-17 producing CD4{sup +} T cells. The semi-mature DC-like cells reported here will be useful vehicles for DC immunization and might contribute to studies on the possible involvement of semi-mature DCs in Th17 cell differentiation.« less

Phenotypes of gene disruptants in relation to a putative mitochondrial malate-citrate shuttle protein in citric acid-producing Aspergillus niger.

PubMed

Kirimura, Kohtaro; Kobayashi, Keiichi; Ueda, Yuka; Hattori, Takasumi

2016-09-01

The mitochondrial citrate transport protein (CTP) functions as a malate-citrate shuttle catalyzing the exchange of citrate plus a proton for malate between mitochondria and cytosol across the inner mitochondrial membrane in higher eukaryotic organisms. In this study, for functional analysis, we cloned the gene encoding putative CTP (ctpA) of citric acid-producing Aspergillus niger WU-2223L. The gene ctpA encodes a polypeptide consisting 296 amino acids conserved active residues required for citrate transport function. Only in early-log phase, the ctpA disruptant DCTPA-1 showed growth delay, and the amount of citric acid produced by strain DCTPA-1 was smaller than that by parental strain WU-2223L. These results indicate that the CTPA affects growth and thereby citric acid metabolism of A. niger changes, especially in early-log phase, but not citric acid-producing period. This is the first report showing that disruption of ctpA causes changes of phenotypes in relation to citric acid production in A. niger.

First report of a lyase for cepacian, the polysaccharide produced by Burkholderia cepacia complex bacteria.

PubMed

Cescutti, Paola; Scussolin, Silvia; Herasimenka, Yury; Impallomeni, Giuseppe; Bicego, Massimiliano; Rizzo, Roberto

2006-01-20

Bacteria belonging to the Burkholderia cepacia complex (Bcc) are interesting for their involvement in pulmonary infections in patients affected by cystic fibrosis (CF) or chronic granulomatous disease. Many Bcc strains isolated from CF patients produce high amounts of exopolysaccharides (EPS). Although different strains sometimes biosynthesise different EPS, the majority of Bcc bacteria produce only one type of polysaccharide, which is called cepacian. The polymer has a unique heptasaccharidic repeating unit, containing three side chains, and up to three O-acetyl substituents.. We here report for the first time the isolation and characterisation of a lyase active towards cepacian produced by a Bacillus sp., which was isolated in our laboratory. The enzyme molecular mass, evaluated by size-exclusion chromatography, is 32,700+/-1500Da. The enzyme catalyses a beta-elimination reaction of the disaccharide side chain beta-d-Galp-(1-->2)-alpha-d-Rhap-(1--> from the C-4 of the glucuronic acid residue present in the polymer backbone. Although active on both native and de-acetylated cepacian, the enzyme showed higher activity on the latter polymer.

Roller compaction: Effect of morphology and amorphous content of lactose powder on product quality.

PubMed

Omar, Chalak S; Dhenge, Ranjit M; Osborne, James D; Althaus, Tim O; Palzer, Stefan; Hounslow, Michael J; Salman, Agba D

2015-12-30

The effect of morphology and amorphous content, of three types of lactose, on the properties of ribbon produced using roller compaction was investigated. The three types of lactose powders were; anhydrous SuperTab21AN, α-lactose monohydrate 200 M, and spray dried lactose SuperTab11SD. The morphology of the primary particles was identified using scanning electron microscopy (SEM) and the powder amorphous content was quantified using NIR technique. SEM images showed that 21AN and SD are agglomerated type of lactose whereas the 200 M is a non-agglomerated type. During ribbon production, an online thermal imaging technique was used to monitor the surface temperature of the ribbon. It was found that the morphology and the amorphous content of lactose powders have significant effects on the roller compaction behaviour and on ribbon properties. The agglomerated types of lactose produced ribbon with higher surface temperature and tensile strength, larger fragment size, lower porosity and lesser fines percentages than the non-agglomerated type of lactose. The lactose powder with the highest amorphous content showed to result in a better binding ability between the primary particles. This type of lactose produced ribbons with the highest temperature and tensile strength, and the lowest porosity and amount of fines in the product. It also produced ribbon with more smooth surfaces in comparison to the other two types of lactose. It was noticed that there is a relationship between the surface temperature of the ribbon during production and the tensile strength of the ribbon; the higher the temperature of the ribbon during production the higher the tensile strength of the ribbon. Copyright © 2015 Elsevier B.V. All rights reserved.

Application of a set of complementary techniques to understand how varying the proportion of two wastes affects humic acids produced by vermicomposting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fernández-Gómez, Manuel J., E-mail: manuelj.fernandez@eez.csic.es; Nogales, Rogelio; Plante, Alain

2015-01-15

Highlights: • A set of techniques was used to characterize humic acids content of vermicomposts. • The properties of the humic acids produced from different waste mixtures were similar. • This set of techniques allowed distinguishing the humic acids of each vermicomposts. • Increasing humic acid contents in initial mixtures would produce richer vermicomposts. - Abstract: A better understanding of how varying the proportion of different organic wastes affects humic acid (HA) formation during vermicomposting would be useful in producing vermicomposts enriched in HAs. With the aim of improving the knowledge about this issue, a variety of analytical techniques [UV–visiblemore » spectroscopic, Fourier transform infrared, fluorescence spectra, solid-state cross-polarization magic-angle spinning (CPMAS) {sup 13}C nuclear magnetic resonance (NMR) spectra, and thermal analysis] was used in the present study to characterize HAs isolated from two mixtures at two different ratios (2:1 and 1:1) of tomato-plant debris (TD) and paper-mill sludge (PS) before and after vermicomposting. The results suggest that vermicomposting increased the HA content in the TD/PS 2:1 and 1:1 mixtures (15.9% and 16.2%, respectively), but the vermicompost produced from the mixture with a higher amount of TD had a greater proportion (24%) of HAs. Both vermicomposting processes caused equal modifications in the humic precursors contained in the different mixtures of TD and PS, and consequently, the HAs in the vermicomposts produced from different waste mixtures exhibited analogous characteristics. Only the set of analytical techniques used in this research was able to detect differences between the HAs isolated from each type of vermicompost. In conclusion, varying the proportion of different wastes may have a stronger influence on the amount of HAs in vermicomposts than on the properties of HAs.« less

Primary fatty acid amide metabolism: conversion of fatty acids and an ethanolamine in N18TG2 and SCP cells.

PubMed

Farrell, Emma K; Chen, Yuden; Barazanji, Muna; Jeffries, Kristen A; Cameroamortegui, Felipe; Merkler, David J

2012-02-01

Primary fatty acid amides (PFAM) are important signaling molecules in the mammalian nervous system, binding to many drug receptors and demonstrating control over sleep, locomotion, angiogenesis, and many other processes. Oleamide is the best-studied of the primary fatty acid amides, whereas the other known PFAMs are significantly less studied. Herein, quantitative assays were used to examine the endogenous amounts of a panel of PFAMs, as well as the amounts produced after incubation of mouse neuroblastoma N(18)TG(2) and sheep choroid plexus (SCP) cells with the corresponding fatty acids or N-tridecanoylethanolamine. Although five endogenous primary amides were discovered in the N(18)TG(2) and SCP cells, a different pattern of relative amounts were found between the two cell lines. Higher amounts of primary amides were found in SCP cells, and the conversion of N-tridecanoylethanolamine to tridecanamide was observed in the two cell lines. The data reported here show that the N(18)TG(2) and SCP cells are excellent model systems for the study of PFAM metabolism. Furthermore, the data support a role for the N-acylethanolamines as precursors for the PFAMs and provide valuable new kinetic results useful in modeling the metabolic flux through the pathways for PFAM biosynthesis and degradation.

Primary fatty acid amide metabolism: conversion of fatty acids and an ethanolamine in N18TG2 and SCP cells1[S

PubMed Central

Farrell, Emma K.; Chen, Yuden; Barazanji, Muna; Jeffries, Kristen A.; Cameroamortegui, Felipe; Merkler, David J.

2012-01-01

Primary fatty acid amides (PFAM) are important signaling molecules in the mammalian nervous system, binding to many drug receptors and demonstrating control over sleep, locomotion, angiogenesis, and many other processes. Oleamide is the best-studied of the primary fatty acid amides, whereas the other known PFAMs are significantly less studied. Herein, quantitative assays were used to examine the endogenous amounts of a panel of PFAMs, as well as the amounts produced after incubation of mouse neuroblastoma N18TG2 and sheep choroid plexus (SCP) cells with the corresponding fatty acids or N-tridecanoylethanolamine. Although five endogenous primary amides were discovered in the N18TG2 and SCP cells, a different pattern of relative amounts were found between the two cell lines. Higher amounts of primary amides were found in SCP cells, and the conversion of N-tridecanoylethanolamine to tridecanamide was observed in the two cell lines. The data reported here show that the N18TG2 and SCP cells are excellent model systems for the study of PFAM metabolism. Furthermore, the data support a role for the N-acylethanolamines as precursors for the PFAMs and provide valuable new kinetic results useful in modeling the metabolic flux through the pathways for PFAM biosynthesis and degradation. PMID:22095832

Influence of soil arsenic on the growth of lowbush blueberry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anastasia, F.B.; Kender, W.J.

1973-01-01

Samples of commercial and virgin soils taken from various lowbush blueberry (Vaccinium angustifolium Ait) areas in Maine contained measurable amounts of As. The highest levels were found in soils from commercial fields which had been repeatedly treated with calcium arsenate for insect control. The amount of As decreased as the soil depth increased. Soils from commercial blueberry fields ranged from 7.7 to 37.8 ppm while virgin soils ranged from 5.7 to 7.0 ppm in the upper levels. Lowbush blueberry plants grown as As levels of 7.7, 17.1, 43.8, 69.5, and 84.5 ppm in a loamy sand in the greenhouse weremore » injured only at the highest level. At 69.5 ppm As and higher blueberry plant growth was significantly inhibited when compared to plants grown at 7.7 ppm As. The greatest As accumulation in blueberry tissue occurred in the roots with decreasing amounts in the stems and leaves, respectively. When foliar As reached 6.7 ppm, a significant reduction in plant growth resulted. Although As was present in all field soils analyzed, at no point did the amount found exceed that which was necessary to produce a reduction in plant growth under greenhouse conditions.« less

Phenolic composition of the edible parts (flesh and skin) of Bordô grape (Vitis labrusca) using HPLC-DAD-ESI-MS/MS.

PubMed

Lago-Vanzela, Ellen Silva; Da-Silva, Roberto; Gomes, Eleni; García-Romero, Esteban; Hermosín-Gutiérrez, Isidro

2011-12-28

The aim of this study was the detailed characterization of the phenolic composition and the determination of the antioxidant activity of the Bordô grape (Vitis labrusca) cultivated in South Brazil. The edible parts of Bordô grapes (flesh and skin) contained 1130 mg/kg of total phenolic compounds (as gallic acid), mainly located in the skins. Anthocyanin content in the skins was high, largely as 3,5-diglucosides (1359 mg/kg, as malvidin 3,5-diglucoside). Total flavonols accounted for 154 μmol/kg, mainly located in the skins and with myricetin 3-glucoside as the principal flavonol in both grape parts. Very low amounts of flavan-3-ol monomers and dimers and low amounts of polymeric proanthocyanidins, with a composition similar to that reported for V. vinifera grape varieties, were found in Bordô grape skins. Hydroxycinnamic acid derivatives mainly derived from caffeic acid and were found in the skins in high amounts, ten times higher than in the flesh (total amount: 483 μmol/kg). Finally, the Bordô grape cultivar can be considered a high resveratrol producer (10.91 mg/kg) and also exhibited a high value of total antioxidant capacity (37.6 ± 1.0 mmol/kg, as Trolox).

7 CFR 1001.71 - Payments to the producer-settlement fund.

Code of Federal Regulations, 2014 CFR

2014-01-01

... to the handler for the month as determined pursuant to § 1001.60. (b) The sum of: (1) An amount... multiplying the total pounds of protein, other solids, and butterfat contained in producer milk by the protein, other solids, and butterfat prices respectively; and (3) An amount obtained by multiplying the pounds of...

7 CFR 1001.71 - Payments to the producer-settlement fund.

Code of Federal Regulations, 2010 CFR

2010-01-01

... to the handler for the month as determined pursuant to § 1001.60. (b) The sum of: (1) An amount... multiplying the total pounds of protein, other solids, and butterfat contained in producer milk by the protein, other solids, and butterfat prices respectively; and (3) An amount obtained by multiplying the pounds of...

7 CFR 1001.71 - Payments to the producer-settlement fund.

Code of Federal Regulations, 2012 CFR

2012-01-01

... to the handler for the month as determined pursuant to § 1001.60. (b) The sum of: (1) An amount... multiplying the total pounds of protein, other solids, and butterfat contained in producer milk by the protein, other solids, and butterfat prices respectively; and (3) An amount obtained by multiplying the pounds of...

7 CFR 1001.71 - Payments to the producer-settlement fund.

Code of Federal Regulations, 2013 CFR

2013-01-01

... to the handler for the month as determined pursuant to § 1001.60. (b) The sum of: (1) An amount... multiplying the total pounds of protein, other solids, and butterfat contained in producer milk by the protein, other solids, and butterfat prices respectively; and (3) An amount obtained by multiplying the pounds of...

7 CFR 1001.71 - Payments to the producer-settlement fund.

Code of Federal Regulations, 2011 CFR

2011-01-01

... to the handler for the month as determined pursuant to § 1001.60. (b) The sum of: (1) An amount... multiplying the total pounds of protein, other solids, and butterfat contained in producer milk by the protein, other solids, and butterfat prices respectively; and (3) An amount obtained by multiplying the pounds of...

Process for producing a clean hydrocarbon fuel from high calcium coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kindig, J.K.

A method is described for substantially reducing the amount of at least one insoluble fluoride-forming species selected from the group consisting of Group IA species and Group IIA species. The species is present in a coal feed material comprising: forming a slurry of a coal feed; a fluoride acid in an amount to produce a first molar concentration of free-fluoride-ions; at least one fluoride-complexing species, the total of all fluoride-complexing species in the slurry being present in an amount to produce a second molar concentration, the second molar concentration being at least equal to that amount such that the ratiomore » of the first molar concentration to the second molar concentration is substantially equal to the stoichiometric ratio of fluoride in at least one tightly-bound complexion so as to from tightly-bound complexions with substantially all free-fluoride ions in the slurry to produce a leached coal product and a spent leach liquor; and separating the leached coal product from the spent leach liquor.« less

Fatty acid profile and elemental content of avocado (Persea americana Mill.) oil--effect of extraction methods.

PubMed

Reddy, Mageshni; Moodley, Roshila; Jonnalagadda, Sreekanth B

2012-01-01

Interest in vegetable oil extracted from idioblast cells of avocado fruit is growing. In this study, five extraction methods to produce avocado oil have been compared: traditional solvent extraction using a Soxhlet or ultrasound, Soxhlet extraction combined with microwave or ultra-turrax treatment and supercritical fluid extraction (SFE). Traditional Soxhlet extraction produced the most reproducible results, 64.76 ± 0.24 g oil/100 g dry weight (DW) and 63.67 ± 0.20 g oil/100 g DW for Hass and Fuerte varieties, respectively. Microwave extraction gave the highest yield of oil (69.94%) from the Hass variety. Oils from microwave extraction had the highest fatty acid content; oils from SFE had wider range of fatty acids. Oils from Fuerte variety had a higher monounsaturated: saturated FA ratio (3.45-3.70). SFE and microwave extraction produced the best quality oil, better than traditional Soxhlet extraction, with the least amount of oxidizing metals present. Copyright © Taylor & Francis Group, LLC

Utilization of different waste proteins to create a novel PGPR-containing bio-organic fertilizer

PubMed Central

Huang, Yan; Sun, Li; Zhao, Jianshu; Huang, Rong; Li, Rong; Shen, Qirong

2015-01-01

High-quality bio-organic fertilizers (BIOs) cannot be produced without the addition of some proteins, while many waste proteins are haphazardly disposed, causing serious environmental pollution. In this study, several waste proteins were used as additives to assist with the reproduction of the functional microbe (Bacillus amyloliquefaciens SQR9) inoculated into matured composts to produce BIOs. An optimized composition of solid-state fermentation (SSF) raw materials was predicted by response surface methodology and experimental validation. The results showed that 7.61% (w/w, DW, the same below) rapeseed meal, 8.85% expanded feather meal, 6.47% dewatered blue algal sludge and 77.07% chicken compost resulted in maximum biomass of strain SQR-9 and the maximum amount of lipopeptides 7 days after SSF. Spectroscopy experiments showed that the inner material structural changes in the novel SSF differed from the control and the novel BIO had higher dissolved organic matter. This study offers a high value-added utilization of waste proteins for producing economical but high-quality BIO. PMID:25586328

Molybdenum toxicity and hypocuprosis in ruminants: a review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ward, G.M.

1978-01-01

Elevated Mo intakes depress Cu availability and may produce a physiological Cu deficiency in ruminants. Total sulfur or sulfate in the ration generally potentiates the effect of Mo. The ratio of Cu to Mo in feed is important regardless of the absolute amount of each. For this reason, and because of the importance of the S content of the diet, it is impossible to define safe dietary limits for Cu and Mo. Physiological Cu deficiencies are produced by four classes of feeds: (1) high Mo, generally above 100 ppM, (2) low Cu:Mo ratio, 2:1 or less, (3) Cu deficiency, belowmore » 5 ppM, and (4) high protein, 20 to 30% protein in fresh forage. The latter situation probably results from higher levels of sulfide produced from sulfur amino acids during rumen fermentation. Copper sulfide is largely unabsorbed. Future instances of hypocuprosis in the US are most likely to occur from marginal copper deficiencies in forages.« less

Integral recycling of municipal solid waste incineration (MSWI) bottom ash fines (0-2mm) and industrial powder wastes by cold-bonding pelletization.

PubMed

Tang, P; Brouwers, H J H

2017-04-01

The cold-bonding pelletizing technique is applied in this study as an integrated method to recycle municipal solid waste incineration (MSWI) bottom ash fines (BAF, 0-2mm) and several other industrial powder wastes. Artificial lightweight aggregates are produced successfully based on the combination of these solid wastes, and the properties of these artificial aggregates are investigated and then compared with others' results reported in literature. Additionally, methods for improving the aggregate properties are suggested, and the corresponding experimental results show that increasing the BAF amount, higher binder content and addition of polypropylene fibres can improve the pellet properties (bulk density, crushing resistance, etc.). The mechanisms regarding to the improvement of the pellet properties are discussed. Furthermore, the leaching behaviours of contaminants from the produced aggregates are investigated and compared with Dutch environmental legislation. The application of these produced artificial lightweight aggregates are proposed according to their properties. Copyright © 2017 Elsevier Ltd. All rights reserved.

Utilization of different waste proteins to create a novel PGPR-containing bio-organic fertilizer

NASA Astrophysics Data System (ADS)

Huang, Yan; Sun, Li; Zhao, Jianshu; Huang, Rong; Li, Rong; Shen, Qirong

2015-01-01

High-quality bio-organic fertilizers (BIOs) cannot be produced without the addition of some proteins, while many waste proteins are haphazardly disposed, causing serious environmental pollution. In this study, several waste proteins were used as additives to assist with the reproduction of the functional microbe (Bacillus amyloliquefaciens SQR9) inoculated into matured composts to produce BIOs. An optimized composition of solid-state fermentation (SSF) raw materials was predicted by response surface methodology and experimental validation. The results showed that 7.61% (w/w, DW, the same below) rapeseed meal, 8.85% expanded feather meal, 6.47% dewatered blue algal sludge and 77.07% chicken compost resulted in maximum biomass of strain SQR-9 and the maximum amount of lipopeptides 7 days after SSF. Spectroscopy experiments showed that the inner material structural changes in the novel SSF differed from the control and the novel BIO had higher dissolved organic matter. This study offers a high value-added utilization of waste proteins for producing economical but high-quality BIO.

Isolation and characterization of bacterium producing lipid from short-chain fatty acids.

PubMed

Okamura, Yoshiko; Nakai, Shota; Ohkawachi, Masahiko; Suemitsu, Masahiro; Takahashi, Hirokazu; Aki, Tsunehiro; Matsumura, Yukihiko; Tajima, Takahisa; Nakashimada, Yutaka; Matsumoto, Mitsufumi

2016-02-01

Anaerobic fermentation generates propionic acid, which inhibits microbial growth and accumulates in wastewater containing increased amounts of organic matter. We therefore isolated a propionic acid-assimilating bacterium that could produce triacylglycerol, for use in wastewater treatment. Nitratireductor sp. strain OM-1 can proliferate in medium containing propionic, acetic, butyric, and valeric acids as well as glycerol, and produces triacylglycerol when both propionic and acetic acids or glycerol are present. In composite model wastewater containing acetic acid, propionic acid and glycerol, this strain shows an even higher conversion rate, suggesting that it is suitable for wastewater treatment. Further, nitrogen depletion in medium containing an acetic-propionic acid mixture resulted in the production of the light oil 2-butenoic acid 1-methylethyl ester, but not triacylglycerol. Collectively, our data indicate that strain OM-1 has the potential to reduce accumulation of activated sludge in wastewater treatment and may contribute to the production of biodiesel. Copyright © 2015 Elsevier Ltd. All rights reserved.

Low-molecular-weight thiols in streptomycetes and their potential role as antioxidants.

PubMed Central

Newton, G L; Fahey, R C; Cohen, G; Aharonowitz, Y

1993-01-01

The intracellular low-molecular-weight thiols present in five gram-positive Streptomyces species and one Flavobacterium species were analyzed by high-performance liquid chromatography after fluorescence labeling with monobromobimane. Bacteria were chosen to include penicillin and cephalosporin beta-lactam producers and nonproducers. No significant amount of glutathione was found in any of the streptomycetes. Major intracellular thiols in all strains examined were cysteine, coenzyme A, sulfide, thiosulfate, and an unknown thiol designated U17. Those streptomycetes that make beta-lactam antibiotics also produce significant amounts of delta-(L-alpha-aminoadipyl)-L-cysteinyl-D-valine (ACV), a key intermediate in their biosynthesis. In Streptomyces clavuligerus, a potent producer of beta-lactams, the level of ACV was low during the early phase of growth and increased rapidly toward the end of exponential growth, paralleling that of antibiotic production. These and other observations indicate that ACV does not function as a protective thiol in streptomycetes. U17 may have this role since it was the major thiol in all streptomycetes and appeared to occur at levels about 10-fold higher than those of the other thiols measured, including ACV. Purification and amino acid analysis of U17 indicated that it contains cysteine and an unusual amine that is not one of the common amino acids. This thiol is identical to an unknown thiol found previously in Micrococcus roseus and Streptomyces griseus. A high level of ergothioneine was found in Streptomyces lactamdurans, and several unidentified thiols were detected in this and other streptomycetes. PMID:8478335

In-vitro microbial production of conjugated linoleic acid by probiotic L. plantarum strains: Utilization as a functional starter culture in sucuk fermentation.

PubMed

Özer, Cem O; Kılıç, Birol; Kılıç, Gülden Başyiğit

2016-04-01

Twenty-three probiotic Lactobacillus plantarum strains were screened in-vitro to determine their ability to produce conjugated linoleic acid (CLA). L. plantarum AA1-2 and L. plantarum AB20-961 were identified as potential strains for CLA production. Optimum conditions for these strains to produce high levels of CLA were determined by evaluating the amount of added hydrolyzed sunflower oil (HSO) and initial pH levels in a nutrient medium. The highest CLA production was obtained in medium with pH6.0 and 2% HSO (P<0.05). Those strains were then used as starter culture in sucuk fermentation. Five sucuk treatments included a control (no starter culture), two sucuk groups with L. plantarum AA1-2 at the initial pH of 5.8 or 6.0 and two sucuk groups with L. plantarum AB20-961 at the initial pH of 5.8 or 6.0. Results indicate that L. plantarum AB20-961 produced higher amount of CLA in sucuk at initial pH of 5.8 and 6.0 levels during first 24h of fermentation compared with other groups. CLA isomer concentration decreased in all sucuk groups during the rest of the fermentation period (P<0.05) and remained quite stable during the storage. This study demonstrated that probiotic L. plantarum AB20-961 can be used in sucuk manufacturing without posing any quality problems. Copyright © 2015 Elsevier Ltd. All rights reserved.

Recreational technical diving part 1: an introduction to technical diving methods and activities.

PubMed

Mitchell, Simon J; Doolette, David J

2013-06-01

Technical divers use gases other than air and advanced equipment configurations to conduct dives that are deeper and/or longer than typical recreational air dives. The use of oxygen-nitrogen (nitrox) mixes with oxygen fractions higher than air results in longer no-decompression limits for shallow diving, and faster decompression from deeper dives. For depths beyond the air-diving range, technical divers mix helium, a light non-narcotic gas, with nitrogen and oxygen to produce 'trimix'. These blends are tailored to the depth of intended use with a fraction of oxygen calculated to produce an inspired oxygen partial pressure unlikely to cause cerebral oxygen toxicity and a nitrogen fraction calculated to produce a tolerable degree of nitrogen narcosis. A typical deep technical dive will involve the use of trimix at the target depth with changes to gases containing more oxygen and less inert gas during the decompression. Open-circuit scuba may be used to carry and utilise such gases, but this is very wasteful of expensive helium. There is increasing use of closed-circuit 'rebreather' devices. These recycle expired gas and potentially limit gas consumption to a small amount of inert gas to maintain the volume of the breathing circuit during descent and the amount of oxygen metabolised by the diver. This paper reviews the basic approach to planning and execution of dives using these methods to better inform physicians of the physical demands and risks.

A Mechanism for Recent Production of Liquid Water on Mars

NASA Technical Reports Server (NTRS)

Hecht, M. H.; Bridges, N. T.

2003-01-01

Though Mars is a cold, dry planet, with respect to the thermal stability of liquid water at low altitudes it is not terribly different from comparably cold places on Earth. In dry air such water would evaporate faster on Mars, at a rate comparable to a 60 C hot spring on Earth, but the heat loss associated with that evaporation would be mitigated by the poor thermal convection in the thin Martian air. Even at higher altitudes where the atmospheric pressure does not reach the triple point of water, liquid water might theoretically exist in a low-vapor pressure form such as wet soil, in a briny solution, or simply under a layer of dust or snow. The theoretical stability of liquid water does not suggest its occurrence, either on Mars or in Antarctica. In fact, global models have suggested that locations capable of providing sufficient heat for melting are, precisely for that reason, too dry for water to be present. However, the temperature of irregular local structures such as trenches or craters can be markedly warmer than those of the uniform surfaces of global models. The work described here suggests a plausible scenario in which seasonal liquid water might be produced locally, in sheltered locations, through a process of condensation, cold-trapping, buffering, and melting. While the amounts produced in the present climate would be small, copious amounts of meltwater may have been produced at other phases of the orbital cycle, as recently as 20,000 years ago.

Hybrid Composite Using Natural Filler and Multi-Walled Carbon Nanotubes (MWCNTs)

NASA Astrophysics Data System (ADS)

Nabinejad, Omid; Sujan, D.; Rahman, Muhammad Ekhlasur; Liew, Willey Yun Hsien; Davies, Ian J.

2017-12-01

This paper presents an experimental study on the development of hybrid composites comprising of multi-walled carbon nanotubes (MWCNTs) and natural filler (oil palm shell (OPS) powder) within unsaturated polyester (UP) matrix. The results revealed that the dispersion of pristine MWCNTs in the polymer matrix was strongly enhanced through use of the solvent mixing method assisted by ultrasonication. Four different solvents were investigated, namely, ethanol, methanol, styrene and acetone. The best compatibility with minimum side effects on the curing of the polyester resin was exhibited by the styrene solvent and this produced the maximum tensile and flexural properties of the resulting nanocomposites. A relatively small amount of pristine MWCNTs well dispersed within the natural filler polyester composite was found to be capable of improving mechanical properties of hybrid composite. However, increasing the MWCNT amount resulted in increased void content within the matrix due to an associated rapid increase in viscosity of the mixture during processing. Due to this phenomenon, the maximum tensile and flexural strengths of the hybrid composites were achieved at MWCNT contents of 0.2 to 0.4 phr and then declined for higher MWCNT amounts. The flexural modulus also experienced its peak at 0.4 phr MWCNT content whereas the tensile modulus exhibited a general decrease with increasing MWCNT content. Thermal stability analysis using TGA under an oxidative atmosphere showed that adding MWCNTs shifted the endset degradation temperature of the hybrid composite to a higher temperature.

The Effect of Oxygen on Organic Haze Properties

NASA Astrophysics Data System (ADS)

Ugelow, Melissa S.; De Haan, David O.; Hörst, Sarah M.; Tolbert, Margaret A.

2018-05-01

Atmospheric organic hazes are present on many planetary bodies, possibly including the ancient Earth and exoplanets, and can greatly influence surface and atmospheric properties. Here we examine the physical and optical properties of organic hazes produced with molecular nitrogen, methane, carbon dioxide, and increasing amounts of molecular oxygen, and compare them to hazes produced without added oxygen. As molecular oxygen is included in increasing amounts from 0 to 200 ppmv, the mass loading of haze produced decreases nonlinearly. With 200 ppmv molecular oxygen, the mass loading of particles produced is on the order of the amount of organic aerosol in modern Earth’s atmosphere, suggesting that while not a thick organic haze, haze particles produced with 200 ppmv molecular oxygen could still influence planetary climates. Additionally, the hazes produced with increasing amounts of oxygen become increasingly oxidized and the densities increase. For hazes produced with 0, 2 and 20 ppmv oxygen, the densities were found to be 0.94, 1.03 and 1.12 g cm‑3, respectively. Moreover, the hazes produced with 0, 2, and 20 ppmv oxygen are found to have real refractive indices of n = 1.58 ± 0.04, 1.53 ± 0.03 and 1.67 ± 0.03, respectively, and imaginary refractive indices of k={0.001}-0.001+0.002, 0.002 ± 0.002 and {0.002}-0.002+0.003, respectively. These k values demonstrate that the particles formed with oxygen have no absorption within our experimental error, and could result in a light scattering layer in an oxygen-containing atmosphere.

Characteristics of the microwave pyrolysis and microwave CO2-assisted gasification of dewatered sewage sludge.

PubMed

Chun, Young Nam; Jeong, Byeo Ri

2017-07-28

Microwave drying-pyrolysis or drying-gasification characteristics were examined to convert sewage sludge into energy and resources. The gasification was carried out with carbon dioxide as a gasifying agent. The examination results were compared with those of the conventional heating-type electric furnace to compare both product characteristics. Through the pyrolysis or gasification, gas, tar, and char were generated as products. The produced gas was the largest component of each process, followed by the sludge char and the tar. During the pyrolysis process, the main components of the produced gas were hydrogen and carbon monoxide, with a small amount of hydrocarbons such as methane and ethylene. In the gasification process, however, the amount of carbon monoxide was greater than the amount of hydrogen. In microwave gasification, a large amount of heavy tar was produced. The largest amount of benzene in light tar was generated from the pyrolysis or gasification. Ammonia and hydrogen cyanide, which are precursors of NO x , were also generated. In the microwave heating method, the sludge char produced by pyrolysis and gasification had pores in the mesopore range. This could be explained that the gas obtained from the microwave pyrolysis or gasification of the wet sewage sludge can be used as an alternative fuel, but the tar and NO x precursors in the produced gas should be treated. Sludge char can be used as a biomass solid fuel or as a tar removal adsorbent if necessary.

Maltaricin CPN, a new class IIa bacteriocin produced by Carnobacterium maltaromaticum CPN isolated from mould-ripened cheese.

PubMed

Hammi, I; Delalande, F; Belkhou, R; Marchioni, E; Cianferani, S; Ennahar, S

2016-11-01

The purpose of this study was to isolate, characterize and determine the structure and the antibacterial activities of a bacteriocin produced by Carnobacterium maltaromaticum CPN, a strain isolated from unpasteurized milk Camembert cheese. This bacteriocin, termed maltaricin CPN, was produced at higher amounts in MRS broth at temperatures between 15°C and 25°C. It was purified to homogeneity from culture supernatant by using a simple method consisting of cation-exchange and reversed-phase chromatographies. Mass spectrometry showed that maltaricin was a 4427·29 Da bacteriocin. Its amino acid sequence was determined by Edman degradation which showed that it had close similarity with bacteriocins of the class IIa. Maltaricin CPN consisted in fact of 44 unmodified amino acids including two cysteine residues at positions 9 and 14 linked by a disulphide bond. The antimicrobial activity of maltaricin CPN covered a range of bacteria, with strong activity against many species of Gram-positive bacteria, especially the food-borne pathogen Listeria monocytogenes, but no activity against Gram-negative ones. In the studied conditions, C. maltaromaticum CPN produced a new class IIa bacteriocin with strong anti-Listeria activity. The study covers the purification and the structural characterization of a new bacteriocin produced by strain C. maltaromaticum CPN isolated from Camembert cheese. Its activity against strains of L. monocytogenes and higher production rates at relatively low temperatures show potential technological applications to improve the safety of refrigerated food. © 2016 The Society for Applied Microbiology.

Angiotensin II-producing enzyme III from acidified serum of nephrectomized dogs.

PubMed

Haas, E; Lewis, L; Koshy, T J; Varde, A U; Renerts, L; Bagai, R C

1989-09-01

A highly active angiotensin-producing enzyme (enzyme III) was obtained from the serum of bilaterally nephrectomized dogs by acid treatment and ammonium sulfate fractionation. An inactive precursor (proenzyme III) was converted to enzyme III during prolonged storage (or by treatment with acid or with cathepsin G or by incubation at 38 degrees C as described in the following paper). Enzyme III reacted maximally at pH 7.7 and it produced up to 400 ng of angiotensin II/mL serum/h (i.e., amounts 4000 times higher than that generated by the endogenous renin present in serum after bilateral nephrectomy). Enzyme III produced angiotensin II at identical rates when either dog angiotensinogen or angiotensin I was used as substrate, but the rate was 710 times higher with synthetic tetradecapeptide renin substrate. Enzyme III is not identical to renin, cathepsin G, tonin, enzyme I, enzyme II, the calcium-dependent angiotensin I-converting enzyme, or the calcium-independent carboxy peptidase, which acts by sequential cleavage of angiotensin I. Enzyme III was inhibited by alpha-1-antitrypsin, diisopropyl fluorophosphate, and lima bean trypsin inhibitor (hence it is a serine proteinase). It was not inhibited by Captopril, Teprotide, or Enalapril. It had been reported previously that cathepsin G released from neutrophil granulocytes, by producing high local concentrations of angiotensin II, may provide a mobile means for modulating blood flow in tissue microvasculature during the inflammatory response. The present study offers a new, additional pathway, by enzyme III, for a similar rapid formation of angiotensin II from serum protein substrate or angiotensin I.

Mannanase hydrolysis of spruce galactoglucomannan focusing on the influence of acetylation on enzymatic mannan degradation.

PubMed

Arnling Bååth, Jenny; Martínez-Abad, Antonio; Berglund, Jennie; Larsbrink, Johan; Vilaplana, Francisco; Olsson, Lisbeth

2018-01-01

Galactoglucomannan (GGM) is the most abundant hemicellulose in softwood, and consists of a backbone of mannose and glucose units, decorated with galactose and acetyl moieties. GGM can be hydrolyzed into fermentable sugars, or used as a polymer in films, gels, and food additives. Endo -β-mannanases, which can be found in the glycoside hydrolase families 5 and 26, specifically cleave the mannan backbone of GGM into shorter oligosaccharides. Information on the activity and specificity of different mannanases on complex and acetylated substrates is still lacking. The aim of this work was to evaluate and compare the modes of action of two mannanases from Cellvibrio japonicus ( Cj Man5A and Cj Man26A) on a variety of mannan substrates, naturally and chemically acetylated to varying degrees, including naturally acetylated spruce GGM. Both enzymes were evaluated in terms of cleavage patterns and their ability to accommodate acetyl substitutions. Cj Man5A and Cj Man26A demonstrated different substrate preferences on mannan substrates with distinct backbone and decoration structures. Cj Man5A action resulted in higher amounts of mannotriose and mannotetraose than that of Cj Man26A, which mainly generated mannose and mannobiose as end products. Mass spectrometric analysis of products from the enzymatic hydrolysis of spruce GGM revealed that an acetylated hexotriose was the shortest acetylated oligosaccharide produced by Cj Man5A, whereas Cj Man26A generated acetylated hexobiose as well as diacetylated oligosaccharides. A low degree of native acetylation did not significantly inhibit the enzymatic action. However, a high degree of chemical acetylation resulted in decreased hydrolyzability of mannan substrates, where reduced substrate solubility seemed to reduce enzyme activity. Our findings demonstrate that the two mannanases from C. japonicus have different cleavage patterns on linear and decorated mannan polysaccharides, including the abundant and industrially important resource spruce GGM. Cj Man26A released higher amounts of fermentable sugars suitable for biofuel production, while Cj Man5A, producing higher amounts of oligosaccharides, could be a good candidate for the production of oligomeric platform chemicals and food additives. Furthermore, chemical acetylation of mannan polymers was found to be a potential strategy for limiting the biodegradation of mannan-containing materials.

Cutting Edge: Protection by Antiviral Memory CD8 T Cells Requires Rapidly Produced Antigen in Large Amounts.

PubMed

Remakus, Sanda; Ma, Xueying; Tang, Lingjuan; Xu, Ren-Huan; Knudson, Cory; Melo-Silva, Carolina R; Rubio, Daniel; Kuo, Yin-Ming; Andrews, Andrew; Sigal, Luis J

2018-05-15

Numerous attempts to produce antiviral vaccines by harnessing memory CD8 T cells have failed. A barrier to progress is that we do not know what makes an Ag a viable target of protective CD8 T cell memory. We found that in mice susceptible to lethal mousepox (the mouse homolog of human smallpox), a dendritic cell vaccine that induced memory CD8 T cells fully protected mice when the infecting virus produced Ag in large quantities and with rapid kinetics. Protection did not occur when the Ag was produced in low amounts, even with rapid kinetics, and protection was only partial when the Ag was produced in large quantities but with slow kinetics. Hence, the amount and timing of Ag expression appear to be key determinants of memory CD8 T cell antiviral protective immunity. These findings may have important implications for vaccine design. Copyright © 2018 by The American Association of Immunologists, Inc.

Characterization and Recovery of Valuables from Waste Copper Smelting Slag

NASA Astrophysics Data System (ADS)

Prince, Sarfo; Young, Jamie; Ma, Guojun; Young, Courtney

Silicate slags produced from smelting copper concentrates contains valuables such as Cu and Fe as well as heavy metals such as Pb and As which are considered hazardous. In this paper, various slags were characterized with several techniques: SEM-MLA, XRD, TG-DTA and ICP-MS. A recovery process was developed to separate the valuables from the silicates thereby producing value-added products and simultaneously reducing environmental concerns. Results show that the major phases in air-cooled slag are fayalite and magnetite whereas the water-cooled slag is amorphous. Thermodynamic calculations and carbothermal reduction experiments indicate that most of Cu and Fe can be recovered from both types using minor amounts of lime and alumina and treating at 1350°C (1623K) or higher for 30 min. The secondary slag can be recycled to the glass and/or ceramic industries.

Nonequilibrium electroweak baryogenesis at preheating after inflation

NASA Astrophysics Data System (ADS)

García-Bellido, Juan; Grigoriev, Dmitri; Kusenko, Alexander; Shaposhnikov, Mikhail

1999-12-01

We present a novel scenario for baryogenesis in a hybrid inflation model at the electroweak scale, in which the standard model Higgs field triggers the end of inflation. One of the conditions for successful baryogenesis, the departure from thermal equilibrium, is naturally achieved at the stage of preheating after inflation. The inflaton oscillations induce large occupation numbers for long-wavelength configurations of the Higgs and gauge fields, which leads to a large rate of sphaleron transitions. We estimate this rate during the first stages of reheating and evaluate the amount of baryons produced due to a particular type of higher-dimensional CP violating operator. The universe thermalizes through fermion interactions, at a temperature below critical, Trh<~100 GeV, preventing the wash-out of the produced baryon asymmetry. Numerical simulations in 1+1 dimensions support our theoretical analyses.

Sustainable production of green feed from carbon dioxide and hydrogen.

PubMed

Landau, Miron V; Vidruk, Roxana; Herskowitz, Moti

2014-03-01

Carbon dioxide hydrogenation to form hydrocarbons was conducted on two iron-based catalysts, prepared according to procedures described in the literature, and on a new iron spinel catalyst. The CO2 conversion measured in a packed-bed reactor was limited to about 60% because of excessive amounts of water produced in this process. Switching to a system of three packed-bed reactors in series with interim removal of water and condensed hydrocarbons increased CO2 conversion to as much as 89%. The pure spinel catalyst displayed a significantly higher activity and selectivity than those of the other iron catalysts. This process produces a product called green feed, which is similar in composition to the product of a high-temperature, iron-based Fischer–Tropsch process from syngas. The green feed can be readily converted into renewable fuels by well-established technologies.

Synthesis, Consolidation and Characterization of Sol-gel Derived Tantalum-Tungsten Oxide Thermite Composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cervantes, O

2010-06-01

Energetic composite powders consisting of sol-gel (SG) derived nanostructured tungsten oxide were produced with various amounts of micrometer-scale tantalum fuel metal. Such energetic composite powders were ignition-tested and results show that the powders are not sensitive to friction, spark and/or impact ignition. Initial consolidation experiments, using the High Pressure Spark Plasma Sintering (HPSPS) technique, on the SG derived nanostructured tungsten oxide produced samples with higher relative density than can be achieved with commercially available tungsten oxide. The SG derived nanostructured tungsten oxide with immobilized tantalum fuel metal (Ta - WO3) energetic composite was consolidated to a density of 9.17 g·cm-3more » or 93% relative density. In addition, those samples were consolidated without significant pre-reaction of the constituents, thus retaining their stored chemical energy.« less

A simple thick target for production of 89Zr using an 11 MeV cyclotron

PubMed Central

Link, Jeanne M.; Krohn, Kenneth A.; O’Hara, Matthew J.

2017-01-01

The growing interest but limited availability of 89Zr for PET led us to test targets for the 89Y(p,n) reaction. The goal was an easily constructed target for an 11 MeV Siemens cyclotron. Yttrium foils were tested at different thicknesses, angles and currents. A 90° foil tolerated 41 μA without damage and produced ~800 MBq/h, > 20 mCi, an amount adequate for radiochemistry research and human doses in a widely available accelerator. This method should translate to higher energy cyclotrons. PMID:28187357

Influence of adipic acid on tensile and morphology properties of linear low density polyethylene/rambutan peels flour blends

NASA Astrophysics Data System (ADS)

Nadhirah, A. A.; Sam, S. T.; Noriman, N. Z.; Ragunathan, S.; Ismail, H.

2015-07-01

This study investigate about the tensile and morphological properties of degradable polymer produced from linear low density polyethylene/rambutan peel flour (LLDPE/RPF) blends and adipic acid (AA) was used as a compatibilizer by varying the rambutan peel flour (RPF) amount from 0-25wt%. The samples were subjected to tensile and morphological tests. AA compatibilized showed higher strength compared to uncompatibilized blends. The Young's modulus for LLDPE/RPF blends increased with increasing flour content. However, the addition of adipic acid had reduced the Young's Modulus.

Crossover And MTF Characteristics Of A Tabular-Grain X-Ray Film

NASA Astrophysics Data System (ADS)

Huff, K. E.; Wagner, P. W.

1984-08-01

An orthochromatic x-ray film made with tabular silver halide grains has a significantly higher MTF when exposed with green-emitting intensifying screens than do conventional films with similar sensitometric properties. The primary reason for the improved MTF is a decrease in the amount of crossover exposure, i.e., exposure by light that has crossed the support one or more times. Two well-established sensitometric procedures for measuring crossover have been compared. One produces results accurate enough for calculations of MTF relationships. Calculated MTF relationships for tabulargrain and conventional films are compared with measured values.

A simplified method for extracting androgens from avian egg yolks

USGS Publications Warehouse

Kozlowski, C.P.; Bauman, J.E.; Hahn, D.C.

2009-01-01

Female birds deposit significant amounts of steroid hormones into the yolks of their eggs. Studies have demonstrated that these hormones, particularly androgens, affect nestling growth and development. In order to measure androgen concentrations in avian egg yolks, most authors follow the extraction methods outlined by Schwabl (1993. Proc. Nat. Acad. Sci. USA 90:11446-11450). We describe a simplified method for extracting androgens from avian egg yolks. Our method, which has been validated through recovery and linearity experiments, consists of a single ethanol precipitation that produces substantially higher recoveries than those reported by Schwabl.

Microgravity

NASA Image and Video Library

2004-04-15

Astroculture is a suite of technologies used to produce and maintain a closed controlled environment for plant growth. The two most recent missions supported growth of potato, dwarf wheat, and mustard plants and provided scientists with the first opportunity to conduct true plant research in space. Light emitting diodes have particular usefulness for plant growth lighting because they emit a much smaller amount of radiant heat than do conventional lighting sources and because they have potential of directing a higher percentage of the emitted light onto plants surfaces. Furthermore, the high output LED's have emissions in the 600-700 nm waveband, which is of highest efficiency for photosynthesis by plants.

Microgravity

NASA Image and Video Library

2004-04-15

Astroculture is a suite of technologies used to produce and maintain a closed controlled environment for plant growth. The two most recent missions supported growth of potato, dwarf wheat, and mustard plants, and provided scientists with the first opportunity to conduct true plant research in space. Light emitting diodes have particular usefulness for plant growth lighting because they emit a much smaller amount of radiant heat than do conventional lighting sources and because they have potential of directing a higher percentage of the emitted light onto plants surfaces. Furthermore, the high output LED's have emissions in the 600-700 nm waveband, which is of highest efficiency for photosynthesis by plants.

Design and optimization of an experimental bioregenerative life support system with higher plants and silkworms

NASA Astrophysics Data System (ADS)

Hu, Enzhu; Bartsev, Sergey I.; Zhao, Ming; Liu, Professor Hong

The conceptual scheme of an experimental bioregenerative life support system (BLSS) for planetary exploration was designed, which consisted of four elements - human metabolism, higher plants, silkworms and waste treatment. 15 kinds of higher plants, such as wheat, rice, soybean, lettuce, mulberry, et al., were selected as regenerative component of BLSS providing the crew with air, water, and vegetable food. Silkworms, which producing animal nutrition for crews, were fed by mulberry-leaves during the first three instars, and lettuce leaves last two instars. The inedible biomass of higher plants, human wastes and silkworm feces were composted into soil like substrate, which can be reused by higher plants cultivation. Salt, sugar and some household material such as soap, shampoo would be provided from outside. To support the steady state of BLSS the same amount and elementary composition of dehydrated wastes were removed periodically. The balance of matter flows between BLSS components was described by the system of algebraic equations. The mass flows between the components were optimized by EXCEL spreadsheets and using Solver. The numerical method used in this study was Newton's method.

Analysis of Functional Constituents in Mulberry (Morus alba L.) Twigs by Different Cultivars, Producing Areas, and Heat Processings

PubMed Central

Choi, Sang Won; Jang, Yeon Jeong; Lee, Yu Jin; Leem, Hyun Hee; Kim, Eun Ok

2013-01-01

Four functional constituents, oxyresveratrol 3′-O-β-D-glucoside (ORTG), oxyresveratrol (ORT), t-resveratrol (RT), and moracin (MC) were isolated from the ethanolic extract of mulberry (Morus alba L.) twigs by a series of isolation procedures, including solvent fractionation, and silica-gel, ODS-A, and Sephadex LH-20 column chromatographies. Their chemical structures were identified by NMR and FABMS spectral analysis. Quantitative changes of four phytochemicals in mulberry twigs were determined by HPLC according to cultivar, producing area, and heat processing. ORTG was a major abundant compound in the mulberry twigs, and its levels ranged from 23.7 to 105.5 mg% in six different mulberry cultivars. Three other compounds were present in trace amounts (<1 mg/100 g) or were not detected. Among mulberry cultivars examined, “Yongcheon” showed the highest level of ORTG, whereas “Somok” had the least ORTG content. Levels of four phytochemicals in the mulberry twigs harvested in early September were higher than those harvested in early July. Levels of ORTG and ORT in the “Cheongil” mulberry twigs produced in the Uljin area were higher than those produced in other areas. Generally, levels of ORTG and ORT in mulberry twigs decreased with heat processing, such as steaming, and microwaving except roasting, whereas those of RT and MC did not considerably vary according to heat processing. These results suggest that the roasted mulberry twigs may be useful as potential sources of functional ingredients and foods. PMID:24551827

The effect of light and dark periods on the production of ethylene from water-stressed wheat leaves.

PubMed

Wright, S T

1981-10-01

Light was found to inhibit substantially (i.e. up to 88%) the production of ethylene induced by water stress in excised wheat leaves and from the shoots of intact plants. The relatively small amounts of ethylene emanating fron non-stressed leaves were also inhibited by light but to a smaller degree (i.e. up to 61%). In water-stressed leaves the degree of light inhibition of ethylene production was shown to be related to the age of the leaves; the amounts of ethylene diffusing from young leaves (i.e. 6-days old) was inhibited 52% by light whereas in older leaves (i.e. 9-days old) it was inhibited by 85%. Previous studies [Wright (1979) Planta 144, 179-188 and (1980) Planta 148, 381-388] had shown that application of 6-benzyladenine (BA) to leaves a day before wilting, greatly increases the amount of ethylene diffusing from the leaves following wilting (e.g. 8-fold), and to smaller degrees do applications of indole-3-acetic acid (IAA) and gibberellic acid (GA3). On the other hand abscisic acid (ABA) treatment reduces the amount of ethylene produced. In these earlier experiments the ethylene was collected from leaves held under dark or near-dark conditions, so in the present study the activities of these growth regulators (10(-4) mol l(-1) solutions) under dark and light conditions were compared. It was found that they maintained the same relative activities on ethylene emanation (i.e. BA>IAA>GA3>water controls>ABA) under both light and dark conditions. However, because of the inhibitory effect of light, the absolute amounts of ethylene produced from all treatments were always much higher in the dark than in the light (usually about a 6-fold difference). An interesting effect of light treatment on ethylene biosynthesis was found when water-stressed leaves were kept in dark chambers for 41/2 h and then transferred to light. Quite unexpectedly, instead of the rate of ethylene production falling immediately, it continued to be produced at the dark rate (i.e. no light inhibition!) for over 2 h before the rate began to decline, and for a much longer period (i.e. in excess of 41/2 h) if the leaves had previously been sprayed with BA. Predictably, leaves placed in the light (i.e. in leaf chambers) and then transferred to darkness, immediately or very soon produced ethylene at the dark rate. One explanation of these results, which is discussed, would be that the biosynthesis of an ethylene precursor requires an obligatory dark stage. The possible implications of these studies to a survival role of ethylene in plants during periods of water stress is discussed.

Two Different Bacterial Community Types Are Linked with the Low-Methane Emission Trait in Sheep

PubMed Central

Kittelmann, Sandra; Pinares-Patiño, Cesar S.; Seedorf, Henning; Kirk, Michelle R.; Ganesh, Siva; McEwan, John C.; Janssen, Peter H.

2014-01-01

The potent greenhouse gas methane (CH4) is produced in the rumens of ruminant animals from hydrogen produced during microbial degradation of ingested feed. The natural animal-to-animal variation in the amount of CH4 emitted and the heritability of this trait offer a means for reducing CH4 emissions by selecting low-CH4 emitting animals for breeding. We demonstrate that differences in rumen microbial community structure are linked to high and low CH4 emissions in sheep. Bacterial community structures in 236 rumen samples from 118 high- and low-CH4 emitting sheep formed gradual transitions between three ruminotypes. Two of these (Q and S) were linked to significantly lower CH4 yields (14.4 and 13.6 g CH4/kg dry matter intake [DMI], respectively) than the third type (H; 15.9 g CH4/kg DMI; p<0.001). Low-CH4 ruminotype Q was associated with a significantly lower ruminal acetate to propionate ratio (3.7±0.4) than S (4.4±0.7; p<0.001) and H (4.3±0.5; p<0.001), and harbored high relative abundances of the propionate-producing Quinella ovalis. Low-CH4 ruminotype S was characterized by lactate- and succinate-producing Fibrobacter spp., Kandleria vitulina, Olsenella spp., Prevotella bryantii, and Sharpea azabuensis. High-CH4 ruminotype H had higher relative abundances of species belonging to Ruminococcus, other Ruminococcaceae, Lachnospiraceae, Catabacteriaceae, Coprococcus, other Clostridiales, Prevotella, other Bacteroidales, and Alphaproteobacteria, many of which are known to form significant amounts of hydrogen. We hypothesize that lower CH4 yields are the result of bacterial communities that ferment ingested feed to relatively less hydrogen, which results in less CH4 being formed. PMID:25078564

From waste water treatment to land management: Conversion of aquatic biomass to biochar for soil amelioration and the fortification of crops with essential trace elements.

PubMed

Roberts, David A; Paul, Nicholas A; Cole, Andrew J; de Nys, Rocky

2015-07-01

Macroalgae can be grown in industrial waste water to sequester metals and the resulting biomass used for biotechnological applications. We have previously cultivated the freshwater macroalga Oedogonium at a coal-fired power station to treat a metal-contaminated effluent from that facility. We then produced biochar from this biomass and determined the suitability of both the biomass and the biochar for soil amelioration. The dried biomass of Oedogonium cultivated in the waste water contained several elements for which there are terrestrial biosolids criteria (As, Cd, Cr, Cu, Pb, Ni, Se and Zn) and leached significant amounts of these elements into solution. Here, we demonstrate that these biomass leachates impair the germination and growth of radishes as a model crop. However, the biochar produced from this same biomass leaches negligible amounts of metal into solution and the leachates support high germination and growth of radishes. Biochar produced at 750 °C leaches the least metal and has the highest recalcitrant C content. When this biochar is added to a low-quality soil it improves the retention of nutrients (N, P, Ca, Mg, K and Mo) from fertilizer in the soil and the growth of radishes by 35-40%. Radishes grown in the soils amended with the biochar have equal or lower metal contents than radishes grown in soil without biochar, but much higher concentrations of essential trace elements (Mo) and macro nutrients (P, K, Ca and Mg). The cultivation of macroalgae is an effective waste water bioremediation technology that also produces biomass that can be used as a feedstock for conversion to biochar for soil amelioration. Copyright © 2015 Elsevier Ltd. All rights reserved.

Satellite DNA methylation status and expression of selected genes in Bos indicus blastocysts produced in vivo and in vitro.

PubMed

Urrego, R; Bernal-Ulloa, S M; Chavarría, N A; Herrera-Puerta, E; Lucas-Hahn, A; Herrmann, D; Winkler, S; Pache, D; Niemann, H; Rodriguez-Osorio, N

2017-04-01

Bovine embryos produced in vivo and in vitro differ with respect to molecular profiles, including epigenetic marks and gene expression profiles. This study investigated the CpG methylation status in bovine testis satellite I (BTS) and Bos taurus alpha satellite I (BTαS) DNA sequences, and concomitantly the relative abundance of transcripts, critically involved in DNA methylation (DNMT1 and DNMT3A), growth and development (IGF2R) and pluripotency (POU5F1) in Bos indicus embryos produced in vitro or in vivo. Results revealed that methylation of BTS were higher (P < 0.05) in embryos produced in vitro compared with their in vivo produced counterparts, while the methylation status of BTαS was similar in both groups. There were no significant differences in transcript abundance for DNMT3A, IGF2R and POU5F1 between blastocysts produced in vivo and in vitro. However, a significantly lower amount of DNMT1 transcripts was found in the in vitro cultured embryos (P < 0.05) compared with their in vivo derived counterparts. In conclusion, this study reported only minor changes in the expression of developmentally important genes and satellite DNA methylation related to the in vitro embryo production system.

Obtaining accurate amounts of mercury from mercury compounds via electrolytic methods

DOEpatents

Grossman, Mark W.; George, William A.

1987-01-01

A process for obtaining pre-determined, accurate rate amounts of mercury. In one embodiment, predetermined, precise amounts of Hg are separated from HgO and plated onto a cathode wire. The method for doing this involves dissolving a precise amount of HgO which corresponds to a pre-determined amount of Hg desired in an electrolyte solution comprised of glacial acetic acid and H.sub.2 O. The mercuric ions are then electrolytically reduced and plated onto a cathode producing the required pre-determined quantity of Hg. In another embodiment, pre-determined, precise amounts of Hg are obtained from Hg.sub.2 Cl.sub.2. The method for doing this involves dissolving a precise amount of Hg.sub.2 Cl.sub.2 in an electrolyte solution comprised of concentrated HCl and H.sub.2 O. The mercurous ions in solution are then electrolytically reduced and plated onto a cathode wire producing the required, pre-determined quantity of Hg.

Obtaining accurate amounts of mercury from mercury compounds via electrolytic methods

DOEpatents

Grossman, M.W.; George, W.A.

1987-07-07

A process is described for obtaining pre-determined, accurate rate amounts of mercury. In one embodiment, predetermined, precise amounts of Hg are separated from HgO and plated onto a cathode wire. The method for doing this involves dissolving a precise amount of HgO which corresponds to a pre-determined amount of Hg desired in an electrolyte solution comprised of glacial acetic acid and H[sub 2]O. The mercuric ions are then electrolytically reduced and plated onto a cathode producing the required pre-determined quantity of Hg. In another embodiment, pre-determined, precise amounts of Hg are obtained from Hg[sub 2]Cl[sub 2]. The method for doing this involves dissolving a precise amount of Hg[sub 2]Cl[sub 2] in an electrolyte solution comprised of concentrated HCl and H[sub 2]O. The mercurous ions in solution are then electrolytically reduced and plated onto a cathode wire producing the required, pre-determined quantity of Hg. 1 fig.

Process to produce silicon carbide fibers using a controlled concentration of boron oxide vapor

NASA Technical Reports Server (NTRS)

Barnard, Thomas Duncan (Inventor); Lipowitz, Jonathan (Inventor); Nguyen, Kimmai Thi (Inventor)

2001-01-01

A process for producing polycrystalline silicon carbide by heating an amorphous ceramic fiber that contains silicon and carbon in an environment containing boron oxide vapor. The boron oxide vapor is produced in situ by the reaction of a boron containing material such as boron carbide and an oxidizing agent such as carbon dioxide, and the amount of boron oxide vapor can be controlled by varying the amount and rate of addition of the oxidizing agent.

Process to produce silicon carbide fibers using a controlled concentration of boron oxide vapor

NASA Technical Reports Server (NTRS)

Barnard, Thomas Duncan (Inventor); Lipowitz, Jonathan (Inventor); Nguyen, Kimmai Thi (Inventor)

2000-01-01

A process for producing polycrystalline silicon carbide includes heating an amorphous ceramic fiber that contains silicon and carbon in an environment containing boron oxide vapor. The boron oxide vapor is produced in situ by the reaction of a boron containing material such as boron carbide and an oxidizing agent such as carbon dioxide, and the amount of boron oxide vapor can be controlled by varying the amount and rate of addition of the oxidizing agent.

Partial melting of amphibolites in the Eastern Segment of the Sveconorwegian orogen, southern Sweden.

NASA Astrophysics Data System (ADS)

Brophy, E.; Hansen, E. C.; Möller, C.; Huffman, M.

2017-12-01

Mafic migmatites with amphibolitic melanosome and tonalitic leucosome are a common feature in continental collision orogenic zones. However, the anatexis of mafic rocks has received much less attention than anatexis in felsic, intermediate or pelitic compositions. We examined mafic migmatites along a traverse within the Eastern Segment of the 1.14-0.9 Ga Sveconorwegian orogen, between Forsheda and Fegen southern Sweden. This traverse occurs in the center of a >150 km metamorphic transition from sub-greenschist facies in the east to high-pressure granulite and eclogite facies in the west (Möller and Andersson, unpublished metamorphic map). The Eastern Segment is a parautochthonous belt made up of rocks of the Fennoscandian shield that were deformed and metamorphosed during the Sveconorwegian orogeny. Within the traverse amphibolite bodies occur within migmatitic felsic to intermediate orthogneisses. The first appearance of tonalitic leucosome in amphibolite was observed towards the eastern edge of the traverse and continued to occur sporadically westward ranging in abundance (by outcrop area) from 0 to 25 %. The mineral assemblage in amphibolite is hbl + plag ( An30) + qtz + bt ± grt ± ilm ± ttn ± py ± SO2-rich scp. No examples of peritectic pyroxene associated with leucosome were found. The lack of peritectic pyroxene suggests that a water-rich phase was present at the onset of anatexis. The highly variable amount of leucosome further suggests that the amount of melt generated was determined by the amount of water available. Together these suggest that partial was driven by the local influx of a water-rich fluid. In the higher grade portions further west migmatitic amphibolite with tonalitic leucosome occurs in two varieties: one with peritectic pyroxene and relatively small amounts of leucosome, interpreted as forming by water-undersaturated dehydration melting, and another without peritectic pyroxene and with larger amounts of leucosome which is interpreted as having formed from water-fluxed melting (Hansen et al., Lithos, 2015). Thus, water-undersaturated melting in mafic rocks appears to have been limited to the higher-grade portions of the orogen. The variable amounts of leucosome produced by partial melting indicate that the presence of water-rich fluids was localized rather than penetrative.

Issues around household pharmaceutical waste disposal through community pharmacies in Croatia.

PubMed

Jonjić, Danijela; Vitale, Ksenija

2014-06-01

Croatian regulations mandate pharmacies to receive unused medicines from households. Pharmacies are considered as producers and holders of pharmaceutical waste and are obliged to finance this service. Model where pharmacies are responsible for financing disposal of unused medicines without reimbursement is not common in Europe. Present service was not tested before implementation. To investigate the elements of the pharmaceutical waste disposal service provided by pharmacies, and to gain insight into the factors that might influence the effectiveness of the service. Setting All pharmacies in the city of Zagreb. Each pharmacy was asked to weigh the collected waste from the public during a period of 30 days, between June 1st and July 10th of 2011, absent from any media advertisement and answer a specifically designed questionnaire that was exploring possible connections between the amount of collected waste, type of pharmacy ownership, discretion while disposing, location of the container, appropriate labeling and to compare the amount of collected waste between neighborhoods. Quantity of collected unused medicines from the public. Of 210 pharmacies, 91 participated completing the questionnaire (43 % response rate). The total amount of collected waste was 505 kg. Pharmacies owned by the city of Zagreb had higher response rate (74 %) than privately owned pharmacies (36 %), and collected significantly higher amount of waste. Anonymity when disposing influenced collected quantity, while labelling and location of the container did not. There were differences in the amount of collected waste between neighborhoods due to the demographic characteristics and number of pharmacies per capita. The effectiveness of the pharmacy service of collecting unused medicines in Croatia shows a number of weaknesses. The amount of collected medicines is below the European average. Functioning of the service seems to be negatively influenced by the type of pharmacy ownership, distribution of pharmacies and lack of anonymity when disposing unused medicines. Additionally, type of ownership is connected with financial burden for pharmacies. Governmental bodies should examine current legislation regulating pharmaceutical waste disposal, particularly financial responsibility for providing the service, in order to increase pharmacies' compliance. Advertising of the service may increase awareness of the importance of proper disposal of unused medicines.

Stability and Expression Levels of HLA-C on the Cell Membrane Modulate HIV-1 Infectivity

PubMed Central

2017-01-01

ABSTRACT HLA-C expression is associated with a differential ability to control HIV-1 infection. Higher HLA-C levels may lead to better control of HIV-1 infection through both a higher efficiency of antigen presentation to cytotoxic T lymphocytes and the triggering of activating killer immunoglobulin-like receptors on NK cells, whereas lower levels may provide poor HIV-1 control and rapid progression to AIDS. We characterized the relative amounts of HLA-C heterotrimers (heavy chain/β2 microglobulin [β2m]/peptide) and HLA-C free heavy chains on peripheral blood mononuclear cells (PBMCs) from healthy blood donors harboring both alleles with stable or unstable binding to β2m/peptide. We analyzed the stability of HLA-C heterotrimers of different allotypes and the infectivity of HIV-1 virions produced by PBMCs with various allotypes. We observed significant differences in HLA-C heterotrimer stability and in expression levels. We found that R5 HIV-1 virions produced by PBMCs harboring unstable HLA-C alleles were more infectious than those produced by PBMCs carrying the stable variants. We propose that HIV-1 infectivity might depend both on the amounts of HLA-C molecules and on their stability as trimeric complex. According to this model, individuals with low-expression HLA-C alleles and unstable binding to β2m/peptide might have worse control of HIV-1 infection and an intrinsically higher capacity to support viral replication. IMPORTANCE Following HIV-1 infection, some people advance rapidly to AIDS while others have slow disease progression. HLA-C, a molecule involved in immunity, is a key determinant of HIV-1 control. Here we reveal how HLA-C variants contribute to the modulation of viral infectivity. HLA-C is present on the cell surface in two different conformations. The immunologically active conformation is part of a complex that includes β2 microglobulin/peptide; the other conformation is not bound to β2 microglobulin/peptide and can associate with HIV-1, increasing its infectivity. Individuals with HLA-C variants with a predominance of immunologically active conformations would display stronger immunity to HIV-1, reduced viral infectivity and effective control of HIV-1 infection, while subjects with HLA-C variants that easily dissociate from β2 microglobulin/peptide would have a reduced immunological response to HIV-1 and produce more infectious virions. This study provides new information that could be useful in the design of novel vaccine strategies and therapeutic approaches to HIV-1. PMID:29070683

Imprints of the ejecta-companion interaction in Type Ia supernovae: main-sequence, subgiant, and red giant companions

NASA Astrophysics Data System (ADS)

Boehner, P.; Plewa, T.; Langer, N.

2017-02-01

We study supernova ejecta-companion interactions in a sample of realistic semidetached binary systems representative of Type Ia supernova progenitor binaries in a single-degenerate scenario. We model the interaction process with the help of a high-resolution hydrodynamic code assuming cylindrical symmetry. We find that the ejecta hole has a half-opening angle of 40-50° with the density by a factor of 2-4 lower, in good agreement with the previous studies. Quantitative differences from the past results in the amounts and kinematics of the stripped companion material and levels of contamination of the companion with the ejecta material can be explained by different model assumptions and effects due to numerical diffusion. We analyse and, for the first time, provide simulation-based estimates of the amounts and of the thermal characteristics of the shock-heated material responsible for producing a prompt, soft X-ray emission. Besides the shocked ejecta material, considered in the original model by Kasen, we also account for the stripped, shock-heated envelope material of stellar companions, which we predict partially contributes to the prompt emission. The amount of the energy deposited in the envelope is comparable to the energy stored in the ejecta. The total energy budget available for the prompt emission is by a factor of about 2-4 smaller than originally predicted by Kasen. Although the shocked envelope has a higher characteristic temperature than the shocked ejecta, the temperature estimates of the shocked material are in good agreement with the Kasen's model. The hottest shocked plasma is produced in the subgiant companion case.

Development of life cycle water footprints for the production of fuels and chemicals from algae biomass.

PubMed

Nogueira Junior, Edson; Kumar, Mayank; Pankratz, Stan; Oyedun, Adetoyese Olajire; Kumar, Amit

2018-09-01

This study develops life cycle water footprints for the production of fuels and chemicals via thermochemical conversion of algae biomass. This study is based on two methods of feedstock production - ponds and photobioreactors (PBRs) - and four conversion pathways - fast pyrolysis, hydrothermal liquefaction (HTL), conventional gasification, and hydrothermal gasification (HTG). The results show the high fresh water requirement for algae production and the necessity to recycle harvested water or use alternative water sources. To produce 1 kg of algae through ponds, 1564 L of water are required. When PBRs are used, only 372 L water are required; however, the energy requirements for PBRs are about 30 times higher than for ponds. From a final product perspective, the pathway based on the gasification of algae biomass was the thermochemical conversion method that required the highest amount of water per MJ produced (mainly due to its low hydrogen yield), followed by fast pyrolysis and HTL. On the other hand, HTG has the lowest water footprint, mainly because the large amount of electricity generated as part of the process compensates for the electricity used by the system. Performance in all pathways can be improved through recycling channels. Copyright © 2018 Elsevier Ltd. All rights reserved.

Fenton process combined with coagulation for the treatment of black liquor from bioethanol wastewater

NASA Astrophysics Data System (ADS)

Muryanto, Muryanto; Hanifah, Ummu; Amriani, Feni; Ibadurrahman, Ahmad Faiz; Sari, Ajeng Arum

2017-11-01

High amounts of black liquor are generated from bioethanol production by using oil palm empty fruit bunches. The black liquor is waste from alkaline pretreatment, it contains high amount of an alkaline solution (NaOH). The black liquor wastewater was highly contaminated with organic materials, and quite toxic for aquatic ecosystems if discharged directly into waters. This study aimed to determine ability of Fenton process combined with coagulation to treat black liquor. The addition 5% of polyaluminium chloride (PAC) could decolorized black liquor, degraded lignin, and produced sludge 70.64%, 68.28%, and 2.76 gram, respectively. Decolorization of black liquor was in line with degradation of black liquor because lignin is the main compound in black liquor. SEM images after addition of PAC of 5% indicated fragmentation of structure. Fenton reagent consist of 0.7 M FeSO4+ 3M H2O2 has able to decolorize black liquor, degrade lignin, and produce sludge 51.67% and 25.44%, and 0.44 gram, respectively. It was concluded that black liquor wastewater from bioethanol can be treated by using Fenton process combined with coagulation. However, these methods still need improvement to obtain the higher degradation rate, and coagulation sludge needs further consideration.

Pressurized Martian-Like Pure CO2 Atmosphere Supports Strong Growth of Cyanobacteria, and Causes Significant Changes in their Metabolism

NASA Astrophysics Data System (ADS)

Murukesan, Gayathri; Leino, Hannu; Mäenpää, Pirkko; Ståhle, Kurt; Raksajit, Wuttinun; Lehto, Harry J.; Allahverdiyeva-Rinne, Yagut; Lehto, Kirsi

2016-03-01

Surviving of crews during future missions to Mars will depend on reliable and adequate supplies of essential life support materials, i.e. oxygen, food, clean water, and fuel. The most economical and sustainable (and in long term, the only viable) way to provide these supplies on Martian bases is via bio-regenerative systems, by using local resources to drive oxygenic photosynthesis. Selected cyanobacteria, grown in adequately protective containment could serve as pioneer species to produce life sustaining substrates for higher organisms. The very high (95.3 %) CO2 content in Martian atmosphere would provide an abundant carbon source for photo-assimilation, but nitrogen would be a strongly limiting substrate for bio-assimilation in this environment, and would need to be supplemented by nitrogen fertilizing. The very high supply of carbon, with rate-limiting supply of nitrogen strongly affects the growth and the metabolic pathways of the photosynthetic organisms. Here we show that modified, Martian-like atmospheric composition (nearly 100 % CO2) under various low pressure conditions (starting from 50 mbar to maintain liquid water, up to 200 mbars) supports strong cellular growth. Under high CO2 / low N2 ratio the filamentous cyanobacteria produce significant amount of H2 during light due to differentiation of high amount of heterocysts.

Passive inhalation of marijuana smoke: urinalysis and room air levels of delta-9-tetrahydrocannabinol

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cone, E.J.; Johnson, R.E.; Darwin, W.D.

In two separate studies, 5 drug-free male volunteers with a history of marijuana use were passively exposed to the sidestream smoke of 4 and 16 marijuana cigarettes (2.8% delta-9-tetrahydrocannabinol (THC)) for 1 h each day for 6 consecutive days. A third study was similarly performed with 2 marijuana-naive subjects passively exposed to the smoke of 16 marijuana cigarettes. Passive smoke exposure was conducted in a small, unventilated room. Room air levels of THC and CO were monitored frequently. All urine specimens were collected and analyzed by EMIT d.a.u. assay, Abuscreen radioimmunoassay and GC/MS. The studies show that significant amounts ofmore » THC were absorbed by all subjects at the higher level of passive smoke exposure (eg., smoke from 16 marijuana cigarettes), resulting in urinary excretion of significant amounts of cannabinoid metabolites. However, it seems improbable that subjects would unknowingly tolerate the noxious smoke conditions produced by this exposure. At the lower level of passive marijuana-smoke exposure, specimens tested positive only infrequently or were negative. Room air levels of THC during passive smoke exposure appeared to be the most critical factor in determining whether a subject produced cannabinoid-positive urine specimens.« less

Solubility of Carbon Dioxide in Water.

ERIC Educational Resources Information Center

Bush, Pat; And Others

1992-01-01

Describes an activity measuring the amount of dissolved carbon dioxide in carbonated water at different temperatures. The amount of carbon dioxide is measured by the amount of dilute ammonia solution needed to produce a pH indicator color change. (PR)

Relationship between environmental factors, dry matter loss and mycotoxin levels in stored wheat and maize infected with Fusarium species.

PubMed

Mylona, Kalliopi; Sulyok, Michael; Magan, Naresh

2012-01-01

This study examined the relationship between storage environmental factors (water activity (a(w)) (0.89-0.97) and temperature (15°C-30°C)), colonisation of wheat and maize by Fusarium graminearum and F. verticillioides respectively and the dry matter losses (DMLs) caused and quantified by contamination with deoxynivalenol (DON), zearalenone (ZEA) and fumonisins (FUMs) during storage. Fungal growth was assessed by the amount of CO(2) produced under different interacting conditions of a(w) and temperature. DMLs were quantified using the cumulative CO(2) data, and these were shown to increase as temperature and a(w) increased. The amount of DON, ZEA (wheat for human consumption) and FUMs (feed maize) produced was significantly affected by the storage conditions. The three toxins however showed different patterns of production. Optimum for DON was at the wettest conditions (0.97a(w)) and the highest temperature assessed (30°C), whereas for ZEA this shifted to 25°C. FUMs were produced in higher amounts in maize at 30°C and 0.97a(w); however, at intermediate a(w) levels (0.955a(w)), the highest production occurred at 25°C followed by 20°C. Polynomial models were developed for the effect of the storage factors on DMLs and toxin production. DMLs under different environmental conditions were significantly correlated with DON and FUMs. DON contamination was above the EU limits in at least 80% of the wheat samples with DMLs >1%, whereas at least 70% of the same samples contained ZEA above the respective EU legislative limits. Similarly, at least 75% of the maize samples with DMLs ≥ 0.9% exceeded the EU limits for the sum of FUMs in feed. These results show that it may be possible to use temporal CO(2) production during storage of grains as an indicator of the level of contamination of the grain with mycotoxins.

Endophytic Fungi from Frankincense Tree Improves Host Growth and Produces Extracellular Enzymes and Indole Acetic Acid

PubMed Central

Khan, Abdul Latif; Al-Harrasi, Ahmed; Al-Rawahi, Ahmed; Al-Farsi, Zainab; Al-Mamari, Aza; Waqas, Muhammad; Asaf, Sajjad; Elyassi, Ali; Mabood, Fazal; Shin, Jae-Ho; Lee, In-Jung

2016-01-01

Boswellia sacra, an economically important frankincense-producing tree found in the desert woodlands of Oman, is least known for its endophytic fungal diversity and the potential of these fungi to produce extracellular enzymes and auxins. We isolated various fungal endophytes belonging to Eurotiales (11.8%), Chaetomiaceae (17.6%), Incertae sadis (29.5%), Aureobasidiaceae (17.6%), Nectriaceae (5.9%) and Sporomiaceae (17.6%) from the phylloplane (leaf) and caulosphere (stem) of the tree. Endophytes were identified using genomic DNA extraction, PCR amplification and sequencing the internal transcribed spacer regions, whereas a detailed phylogenetic analysis of the same gene fragment was made with homologous sequences. The endophytic colonization rate was significantly higher in the leaf (5.33%) than the stem (0.262%). The Shannon-Weiner diversity index was H′ 0.8729, while Simpson index was higher in the leaf (0.583) than in the stem (0.416). Regarding the endophytic fungi’s potential for extracellular enzyme production, fluorogenic 4-methylumbelliferone standards and substrates were used to determine the presence of cellulases, phosphatases and glucosidases in the pure culture. Among fungal strains, Penicillum citrinum BSL17 showed significantly higher amounts of glucosidases (62.15±1.8 μM-1min-1mL) and cellulases (62.11±1.6 μM-1min-1mL), whereas Preussia sp. BSL10 showed significantly higher secretion of glucosidases (69.4±0.79 μM-1min-1mL) and phosphatases (3.46±0.31μM-1min-1mL) compared to other strains. Aureobasidium sp. BSS6 and Preussia sp. BSL10 showed significantly higher potential for indole acetic acid production (tryptophan-dependent and independent pathways). Preussia sp. BSL10 was applied to the host B. sacra tree saplings, which exhibited significant improvements in plant growth parameters and accumulation of photosynthetic pigments. The current study concluded that endophytic microbial resources producing extracellular enzymes and auxin could establish a unique niche for ecological adaptation during symbiosis with the host Frankincense tree. PMID:27359330

Endophytic Fungi from Frankincense Tree Improves Host Growth and Produces Extracellular Enzymes and Indole Acetic Acid.

PubMed

Khan, Abdul Latif; Al-Harrasi, Ahmed; Al-Rawahi, Ahmed; Al-Farsi, Zainab; Al-Mamari, Aza; Waqas, Muhammad; Asaf, Sajjad; Elyassi, Ali; Mabood, Fazal; Shin, Jae-Ho; Lee, In-Jung

2016-01-01

Boswellia sacra, an economically important frankincense-producing tree found in the desert woodlands of Oman, is least known for its endophytic fungal diversity and the potential of these fungi to produce extracellular enzymes and auxins. We isolated various fungal endophytes belonging to Eurotiales (11.8%), Chaetomiaceae (17.6%), Incertae sadis (29.5%), Aureobasidiaceae (17.6%), Nectriaceae (5.9%) and Sporomiaceae (17.6%) from the phylloplane (leaf) and caulosphere (stem) of the tree. Endophytes were identified using genomic DNA extraction, PCR amplification and sequencing the internal transcribed spacer regions, whereas a detailed phylogenetic analysis of the same gene fragment was made with homologous sequences. The endophytic colonization rate was significantly higher in the leaf (5.33%) than the stem (0.262%). The Shannon-Weiner diversity index was H' 0.8729, while Simpson index was higher in the leaf (0.583) than in the stem (0.416). Regarding the endophytic fungi's potential for extracellular enzyme production, fluorogenic 4-methylumbelliferone standards and substrates were used to determine the presence of cellulases, phosphatases and glucosidases in the pure culture. Among fungal strains, Penicillum citrinum BSL17 showed significantly higher amounts of glucosidases (62.15±1.8 μM-1min-1mL) and cellulases (62.11±1.6 μM-1min-1mL), whereas Preussia sp. BSL10 showed significantly higher secretion of glucosidases (69.4±0.79 μM-1min-1mL) and phosphatases (3.46±0.31μM-1min-1mL) compared to other strains. Aureobasidium sp. BSS6 and Preussia sp. BSL10 showed significantly higher potential for indole acetic acid production (tryptophan-dependent and independent pathways). Preussia sp. BSL10 was applied to the host B. sacra tree saplings, which exhibited significant improvements in plant growth parameters and accumulation of photosynthetic pigments. The current study concluded that endophytic microbial resources producing extracellular enzymes and auxin could establish a unique niche for ecological adaptation during symbiosis with the host Frankincense tree.

Mammalian mucosal α-glucosidases coordinate with α-amylase in the initial starch hydrolysis stage to have a role in starch digestion beyond glucogenesis.

PubMed

Dhital, Sushil; Lin, Amy Hui-Mei; Hamaker, Bruce R; Gidley, Michael J; Muniandy, Anbuhkani

2013-01-01

Starch digestion in the human body is typically viewed in a sequential manner beginning with α-amylase and followed by α-glucosidase to produce glucose. This report indicates that the two enzyme types can act synergistically to digest granular starch structure. The aim of this study was to investigate how the mucosal α-glucosidases act with α-amylase to digest granular starch. Two types of enzyme extracts, pancreatic and intestinal extracts, were applied. The pancreatic extract containing predominantly α-amylase, and intestinal extract containing a combination of α-amylase and mucosal α-glucosidase activities, were applied to three granular maize starches with different amylose contents in an in vitro system. Relative glucogenesis, released maltooligosaccharide amounts, and structural changes of degraded residues were examined. Pancreatic extract-treated starches showed a hydrolysis limit over the 12 h incubation period with residues having a higher gelatinization temperature than the native starch. α-Amylase combined with the mucosal α-glucosidases in the intestinal extract showed higher glucogenesis as expected, but also higher maltooligosaccharide amounts indicating an overall greater degree of granular starch breakdown. Starch residues after intestinal extract digestion showed more starch fragmentation, higher gelatinization temperature, higher crystallinity (without any change in polymorph), and an increase of intermediate-sized or small-sized fractions of starch molecules, but did not show preferential hydrolysis of either amylose or amylopectin. Direct digestion of granular starch by mammalian recombinant mucosal α-glucosidases was observed which shows that these enzymes may work either independently or together with α-amylase to digest starch. Thus, mucosal α-glucosidases can have a synergistic effect with α-amylase on granular starch digestion, consistent with a role in overall starch digestion beyond their primary glucogenesis function.

Mammalian Mucosal α-Glucosidases Coordinate with α-Amylase in the Initial Starch Hydrolysis Stage to Have a Role in Starch Digestion beyond Glucogenesis

PubMed Central

Dhital, Sushil; Lin, Amy Hui-Mei; Hamaker, Bruce R.; Gidley, Michael J.; Muniandy, Anbuhkani

2013-01-01

Starch digestion in the human body is typically viewed in a sequential manner beginning with α-amylase and followed by α-glucosidase to produce glucose. This report indicates that the two enzyme types can act synergistically to digest granular starch structure. The aim of this study was to investigate how the mucosal α-glucosidases act with α-amylase to digest granular starch. Two types of enzyme extracts, pancreatic and intestinal extracts, were applied. The pancreatic extract containing predominantly α-amylase, and intestinal extract containing a combination of α-amylase and mucosal α-glucosidase activities, were applied to three granular maize starches with different amylose contents in an in vitro system. Relative glucogenesis, released maltooligosaccharide amounts, and structural changes of degraded residues were examined. Pancreatic extract-treated starches showed a hydrolysis limit over the 12 h incubation period with residues having a higher gelatinization temperature than the native starch. α-Amylase combined with the mucosal α-glucosidases in the intestinal extract showed higher glucogenesis as expected, but also higher maltooligosaccharide amounts indicating an overall greater degree of granular starch breakdown. Starch residues after intestinal extract digestion showed more starch fragmentation, higher gelatinization temperature, higher crystallinity (without any change in polymorph), and an increase of intermediate-sized or small-sized fractions of starch molecules, but did not show preferential hydrolysis of either amylose or amylopectin. Direct digestion of granular starch by mammalian recombinant mucosal α-glucosidases was observed which shows that these enzymes may work either independently or together with α-amylase to digest starch. Thus, mucosal α-glucosidases can have a synergistic effect with α-amylase on granular starch digestion, consistent with a role in overall starch digestion beyond their primary glucogenesis function. PMID:23638112

Relationship between food waste, diet quality, and environmental sustainability

PubMed Central

Niles, Meredith T.; Neher, Deborah A.; Roy, Eric D.; Tichenor, Nicole E.; Jahns, Lisa

2018-01-01

Improving diet quality while simultaneously reducing environmental impact is a critical focus globally. Metrics linking diet quality and sustainability have typically focused on a limited suite of indicators, and have not included food waste. To address this important research gap, we examine the relationship between food waste, diet quality, nutrient waste, and multiple measures of sustainability: use of cropland, irrigation water, pesticides, and fertilizers. Data on food intake, food waste, and application rates of agricultural amendments were collected from diverse US government sources. Diet quality was assessed using the Healthy Eating Index-2015. A biophysical simulation model was used to estimate the amount of cropland associated with wasted food. This analysis finds that US consumers wasted 422g of food per person daily, with 30 million acres of cropland used to produce this food every year. This accounts for 30% of daily calories available for consumption, one-quarter of daily food (by weight) available for consumption, and 7% of annual cropland acreage. Higher quality diets were associated with greater amounts of food waste and greater amounts of wasted irrigation water and pesticides, but less cropland waste. This is largely due to fruits and vegetables, which are health-promoting and require small amounts of cropland, but require substantial amounts of agricultural inputs. These results suggest that simultaneous efforts to improve diet quality and reduce food waste are necessary. Increasing consumers’ knowledge about how to prepare and store fruits and vegetables will be one of the practical solutions to reducing food waste. PMID:29668732

Transformations of inorganic mercury by Candida albicans and Saccharomyces cerevisiae

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yannai, S.; Berdicevsky, I.; Duek, L.

1991-01-01

Saccharomyces cerevisiae and Candida albicans were incubated with 0.25, 0.5, or 0.75 {mu}g of Hg (as HgCl{sub 2}) per ml of Nelson's medium in the presence of trace amounts of oxygen at 28{degree}C for 12 days. Two control media were used, one without added Hg and one without yeast inoculum. Yeast cell growth was estimated after 1, 2, 3, and 8 days of incubation. The contents of organomercury in the system and of elemental mercury released from the media and collected in traps were determined at the end of the experiments. The results were as follows: (1) C. albicans wasmore » the more mercury-resistant species, but both yeast species failed to grown in the media containing 0.75 {mu}g of Hg per ml.; (2) The amounts of organomercury produced by the two species were proportional to the amount of HgCl{sub 2} added to the medium. In all cases C. albicans produced considerably larger amounts of methylmercury than S. cerevisiae; (3) The amounts of elemental Hg produced were inversely proportional to the HgCl{sub 2} level added in the case of S. cerevisiae but were all similar in the case of C. albicans;and (4) Neither organomercury nor elemental Hg was produced in any of the control media.« less

A sustainable woody biomass biorefinery.

PubMed

Liu, Shijie; Lu, Houfang; Hu, Ruofei; Shupe, Alan; Lin, Lu; Liang, Bin

2012-01-01

Woody biomass is renewable only if sustainable production is imposed. An optimum and sustainable biomass stand production rate is found to be one with the incremental growth rate at harvest equal to the average overall growth rate. Utilization of woody biomass leads to a sustainable economy. Woody biomass is comprised of at least four components: extractives, hemicellulose, lignin and cellulose. While extractives and hemicellulose are least resistant to chemical and thermal degradation, cellulose is most resistant to chemical, thermal, and biological attack. The difference or heterogeneity in reactivity leads to the recalcitrance of woody biomass at conversion. A selection of processes is presented together as a biorefinery based on incremental sequential deconstruction, fractionation/conversion of woody biomass to achieve efficient separation of major components. A preference is given to a biorefinery absent of pretreatment and detoxification process that produce waste byproducts. While numerous biorefinery approaches are known, a focused review on the integrated studies of water-based biorefinery processes is presented. Hot-water extraction is the first process step to extract value from woody biomass while improving the quality of the remaining solid material. This first step removes extractives and hemicellulose fractions from woody biomass. While extractives and hemicellulose are largely removed in the extraction liquor, cellulose and lignin largely remain in the residual woody structure. Xylo-oligomers, aromatics and acetic acid in the hardwood extract are the major components having the greatest potential value for development. Higher temperature and longer residence time lead to higher mass removal. While high temperature (>200°C) can lead to nearly total dissolution, the amount of sugars present in the extraction liquor decreases rapidly with temperature. Dilute acid hydrolysis of concentrated wood extracts renders the wood extract with monomeric sugars. At higher acid concentration and higher temperature the hydrolysis produced more xylose monomers in a comparatively shorter period of reaction time. Xylose is the most abundant monomeric sugar in the hydrolysate. The other comparatively small amounts of monomeric sugars include arabinose, glucose, rhamnose, mannose and galactose. Acetic acid, formic acid, furfural, HMF and other byproducts are inevitably generated during the acid hydrolysis process. Short reaction time is preferred for the hydrolysis of hot-water wood extracts. Acid hydrolysis presents a perfect opportunity for the removal or separation of aromatic materials from the wood extract/hydrolysate. The hot-water wood extract hydrolysate, after solid-removal, can be purified by Nano-membrane filtration to yield a fermentable sugar stream. Fermentation products such as ethanol can be produced from the sugar stream without a detoxification step. Copyright © 2012 Elsevier Inc. All rights reserved.

Defenses against keratinolytic bacteria in birds living in radioactively contaminated areas

NASA Astrophysics Data System (ADS)

Ruiz-Rodríguez, Magdalena; Møller, Anders Pape; Mousseau, Timothy A.; Soler, Juan J.

2016-10-01

Microorganisms have shaped the evolution of a variety of defense mechanisms against pathogenic infections. Radioactivity modifies bacterial communities and, therefore, bird hosts breeding in contaminated areas are expected to adapt to the new bacterial environment. We tested this hypothesis in populations of barn swallows ( Hirundo rustica) from a gradient of background radiation levels at Chernobyl and uncontaminated controls from Denmark. Investment in defenses against keratinolytic bacteria was measured from feather structure (i.e., susceptibility to degradation) and uropygial secretions. We studied degradability of tail feathers from areas varying in contamination in laboratory experiments using incubation of feathers with a feather-degrading bacterium, Bacillus licheniformis, followed by measurement of the amount of keratin digested. The size of uropygial glands and secretion amounts were quantified, followed by antimicrobial tests against B. licheniformis and quantification of wear of feathers. Feathers of males, but not of females, from highly contaminated areas degraded at a lower rate than those from medium and low contamination areas. However, feathers of both sexes from the Danish populations showed little evidence of degradation. Individual barn swallows from the more contaminated areas of Ukraine produced the largest uropygial secretions with higher antimicrobial activity, although wear of feathers did not differ among males from different populations. In Denmark, swallows produced smaller quantities of uropygial secretion with lower antimicrobial activity, which was similar to swallow populations from uncontaminated areas in Ukraine. Therefore, barn swallows breeding in contaminated areas invested more in all defenses against keratinolytic bacteria than in uncontaminated areas of Ukraine and Denmark, although they had similar levels of feather wear. Strong natural selection exerted by radioactivity may have selected for individuals with higher defense capacity against bacterial infections during the 30 years since the Chernobyl disaster.

Defenses against keratinolytic bacteria in birds living in radioactively contaminated areas.

PubMed

Ruiz-Rodríguez, Magdalena; Møller, Anders Pape; Mousseau, Timothy A; Soler, Juan J

2016-10-01

Microorganisms have shaped the evolution of a variety of defense mechanisms against pathogenic infections. Radioactivity modifies bacterial communities and, therefore, bird hosts breeding in contaminated areas are expected to adapt to the new bacterial environment. We tested this hypothesis in populations of barn swallows (Hirundo rustica) from a gradient of background radiation levels at Chernobyl and uncontaminated controls from Denmark. Investment in defenses against keratinolytic bacteria was measured from feather structure (i.e., susceptibility to degradation) and uropygial secretions. We studied degradability of tail feathers from areas varying in contamination in laboratory experiments using incubation of feathers with a feather-degrading bacterium, Bacillus licheniformis, followed by measurement of the amount of keratin digested. The size of uropygial glands and secretion amounts were quantified, followed by antimicrobial tests against B. licheniformis and quantification of wear of feathers. Feathers of males, but not of females, from highly contaminated areas degraded at a lower rate than those from medium and low contamination areas. However, feathers of both sexes from the Danish populations showed little evidence of degradation. Individual barn swallows from the more contaminated areas of Ukraine produced the largest uropygial secretions with higher antimicrobial activity, although wear of feathers did not differ among males from different populations. In Denmark, swallows produced smaller quantities of uropygial secretion with lower antimicrobial activity, which was similar to swallow populations from uncontaminated areas in Ukraine. Therefore, barn swallows breeding in contaminated areas invested more in all defenses against keratinolytic bacteria than in uncontaminated areas of Ukraine and Denmark, although they had similar levels of feather wear. Strong natural selection exerted by radioactivity may have selected for individuals with higher defense capacity against bacterial infections during the 30 years since the Chernobyl disaster.

Liquid chromatography-tandem mass spectrometry analysis allows the simultaneous characterization of C-glycosyl and O-glycosyl flavonoids in stingless bee honeys.

PubMed

Truchado, Pilar; Vit, Patricia; Ferreres, Federico; Tomas-Barberan, Francisco

2011-10-21

The analysis of the phytochemicals present in stingless bee honey samples has been a difficult task due to the small amounts of samples available and to the complexity of the phytochemical composition that often combines flavonoid glycosides and aglycones. Honey samples produced in Venezuela from Melipona species were analyzed using a combination of solid-phase extraction and HPLC-DAD-MSn/ESI methodologies with specific study of the fragment ions produced from flavonoid glycosides. The analyses revealed that flavonoid glycosides were the main constituents. The honey samples analyzed contained a consistent flavonoid pattern composed of flavone-C-glycosides, flavonol-O-glycosides and flavonoid aglycones. The HPLC-DAD-MSn/ESI analysis and the study of the fragment ions obtained allowed the characterization and quantification for the first time of five apigenin-di-C-glycosides, and ten quercetin, kaempferol and isorhamnetin O-glycosides (di- and tri- glycosides), and the aglycones pinobanksin, quercetin, kaempferol and isorhamnetin in the different samples. This is the first report of flavonoid-C-glycosides in honey. The results show that the content of flavonoid-glycosides (mean values of 2712 μg/100 g) in stingless bee honeys is considerably higher than the content of flavonoid aglycones (mean values of 315 μg/100 g). This differs from previous studies on Apis mellifera honeys that consistently showed much higher aglycone content and smaller flavonoid glycoside content. The occurrence of relevant amounts of flavonoid glycosides, and particularly C-glycosides, in stingless bee honeys could be associated with their putative anticataract properties. Copyright © 2011 Elsevier B.V. All rights reserved.

Automated processing of whole blood units: operational value and in vitro quality of final blood components

PubMed Central

Jurado, Marisa; Algora, Manuel; Garcia-Sanchez, Félix; Vico, Santiago; Rodriguez, Eva; Perez, Sonia; Barbolla, Luz

2012-01-01

Background The Community Transfusion Centre in Madrid currently processes whole blood using a conventional procedure (Compomat, Fresenius) followed by automated processing of buffy coats with the OrbiSac system (CaridianBCT). The Atreus 3C system (CaridianBCT) automates the production of red blood cells, plasma and an interim platelet unit from a whole blood unit. Interim platelet unit are pooled to produce a transfusable platelet unit. In this study the Atreus 3C system was evaluated and compared to the routine method with regards to product quality and operational value. Materials and methods Over a 5-week period 810 whole blood units were processed using the Atreus 3C system. The attributes of the automated process were compared to those of the routine method by assessing productivity, space, equipment and staffing requirements. The data obtained were evaluated in order to estimate the impact of implementing the Atreus 3C system in the routine setting of the blood centre. Yield and in vitro quality of the final blood components processed with the two systems were evaluated and compared. Results The Atreus 3C system enabled higher throughput while requiring less space and employee time by decreasing the amount of equipment and processing time per unit of whole blood processed. Whole blood units processed on the Atreus 3C system gave a higher platelet yield, a similar amount of red blood cells and a smaller volume of plasma. Discussion These results support the conclusion that the Atreus 3C system produces blood components meeting quality requirements while providing a high operational efficiency. Implementation of the Atreus 3C system could result in a large organisational improvement. PMID:22044958

Automated processing of whole blood units: operational value and in vitro quality of final blood components.

PubMed

Jurado, Marisa; Algora, Manuel; Garcia-Sanchez, Félix; Vico, Santiago; Rodriguez, Eva; Perez, Sonia; Barbolla, Luz

2012-01-01

The Community Transfusion Centre in Madrid currently processes whole blood using a conventional procedure (Compomat, Fresenius) followed by automated processing of buffy coats with the OrbiSac system (CaridianBCT). The Atreus 3C system (CaridianBCT) automates the production of red blood cells, plasma and an interim platelet unit from a whole blood unit. Interim platelet unit are pooled to produce a transfusable platelet unit. In this study the Atreus 3C system was evaluated and compared to the routine method with regards to product quality and operational value. Over a 5-week period 810 whole blood units were processed using the Atreus 3C system. The attributes of the automated process were compared to those of the routine method by assessing productivity, space, equipment and staffing requirements. The data obtained were evaluated in order to estimate the impact of implementing the Atreus 3C system in the routine setting of the blood centre. Yield and in vitro quality of the final blood components processed with the two systems were evaluated and compared. The Atreus 3C system enabled higher throughput while requiring less space and employee time by decreasing the amount of equipment and processing time per unit of whole blood processed. Whole blood units processed on the Atreus 3C system gave a higher platelet yield, a similar amount of red blood cells and a smaller volume of plasma. These results support the conclusion that the Atreus 3C system produces blood components meeting quality requirements while providing a high operational efficiency. Implementation of the Atreus 3C system could result in a large organisational improvement.

Electrical conductivity during incipient melting in the oceanic low-velocity zone.

PubMed

Sifré, David; Gardés, Emmanuel; Massuyeau, Malcolm; Hashim, Leila; Hier-Majumder, Saswata; Gaillard, Fabrice

2014-05-01

The low-viscosity layer in the upper mantle, the asthenosphere, is a requirement for plate tectonics. The seismic low velocities and the high electrical conductivities of the asthenosphere are attributed either to subsolidus, water-related defects in olivine minerals or to a few volume per cent of partial melt, but these two interpretations have two shortcomings. First, the amount of water stored in olivine is not expected to be higher than 50 parts per million owing to partitioning with other mantle phases (including pargasite amphibole at moderate temperatures) and partial melting at high temperatures. Second, elevated melt volume fractions are impeded by the temperatures prevailing in the asthenosphere, which are too low, and by the melt mobility, which is high and can lead to gravitational segregation. Here we determine the electrical conductivity of carbon-dioxide-rich and water-rich melts, typically produced at the onset of mantle melting. Electrical conductivity increases modestly with moderate amounts of water and carbon dioxide, but it increases drastically once the carbon dioxide content exceeds six weight per cent in the melt. Incipient melts, long-expected to prevail in the asthenosphere, can therefore produce high electrical conductivities there. Taking into account variable degrees of depletion of the mantle in water and carbon dioxide, and their effect on the petrology of incipient melting, we calculated conductivity profiles across the asthenosphere for various tectonic plate ages. Several electrical discontinuities are predicted and match geophysical observations in a consistent petrological and geochemical framework. In moderately aged plates (more than five million years old), incipient melts probably trigger both the seismic low velocities and the high electrical conductivities in the upper part of the asthenosphere, whereas in young plates, where seamount volcanism occurs, a higher degree of melting is expected.

Anthropogenic (PBDE) and naturally-produced (MeO-PBDE) brominated compounds in cetaceans--a review.

PubMed

Alonso, Mariana B; Azevedo, Alexandre; Torres, João Paulo M; Dorneles, Paulo R; Eljarrat, Ethel; Barceló, Damià; Lailson-Brito, José; Malm, Olaf

2014-05-15

This paper reviews the available data on brominated flame retardants, the polybrominated diphenyl ethers (PBDEs), as well as on the naturally-produced methoxylated polybrominated diphenyl ethers (MeO-PBDEs) in cetacean tissues around the world. Levels and possible sources of both compound classes are discussed. Odontocete cetaceans accumulate higher PBDE concentrations than mysticete species. PBDE contamination was higher in cetaceans from the Northern hemisphere, whereas MeO-PBDE levels were higher in animals from the Southern hemisphere. Southern resident killer whales from NE Pacific presented the highest levels reported in biota, followed by bottlenose dolphins from North Atlantic (U.K. and U.S. coast). Many species presented PBDE concentrations above threshold levels for health effects in odontocetes. Time trend studies indicate that PBDE concentrations in odontocetes from Japan, China, U.S. and Canada coastal zones have increased significantly over the past 30 years. Studies from U.K. waters and NE Atlantic showed a decrease and/or stability of PBDE levels in cetacean tissues in recent decades. The highest MeO-PBDE concentrations were found in dolphins from Tanzania (Indian Ocean), bottlenose dolphins from Queensland, Australia (SW Pacific), and odontocetes from coastal and continental shelf waters off southeastern Brazil (SW Atlantic). The upwelling phenomenon and the presence of coral reef complexes in these tropical oceans may explain the large amounts of the naturally-produced organobromines. Considering that these bioaccumulative chemicals have properties that could cause many deleterious effects in those animals, future studies are required to evaluate the potential ecotoxicological risks. Copyright © 2014 Elsevier B.V. All rights reserved.

Profiling of lipid and glycogen accumulations under different growth conditions in the sulfothermophilic red alga Galdieria sulphuraria.

PubMed

Sakurai, Toshihiro; Aoki, Motohide; Ju, Xiaohui; Ueda, Tatsuya; Nakamura, Yasunori; Fujiwara, Shoko; Umemura, Tomonari; Tsuzuki, Mikio; Minoda, Ayumi

2016-01-01

The unicellular red alga Galdieria sulphuraria grows efficiently and produces a large amount of biomass in acidic conditions at high temperatures. It has great potential to produce biofuels and other beneficial compounds without becoming contaminated with other organisms. In G. sulphuraria, biomass measurements and glycogen and lipid analyses demonstrated that the amounts and compositions of glycogen and lipids differed when cells were grown under autotrophic, mixotrophic, and heterotrophic conditions. Maximum biomass production was obtained in the mixotrophic culture. High amounts of glycogen were obtained in the mixotrophic cultures, while the amounts of neutral lipids were similar between mixotrophic and heterotrophic cultures. The amounts of neutral lipids were highest in red algae, including thermophiles. Glycogen structure and fatty acids compositions largely depended on the growth conditions. Copyright © 2015. Published by Elsevier Ltd.

The future role of chemicals in forestry.

Treesearch

Tarrant R.F.; H.J. Gratkowski; W.E. Waters

1973-01-01

As a result of an increasing population, our reduced acreage of forest land will be called upon to produce maximum amounts of wood fiber, to satisfy an ever-increasing demand for recreational use, and to produce maximum amounts of clean, pure water. Under such demands, forestry must be practiced with an intensity that is beyond our ability to conceive at present. Of...

Accumulation of a 5’ proximal subgenomic RNA of Citrus tristeza virus is correlated with encapsidation by the minor coat protein

USDA-ARS?s Scientific Manuscript database

During replication, Citrus tristeza virus (CTV) produces large amounts of two unusual subgenomic (sg) RNAs that are positive-stranded and 5' -coterminal. Although these RNAs are produced in similar amounts and are similar in size, with LMT1 (~750 nt) only slightly larger than LMT2 (~650), we found ...

Foamed lightweight materials made from mixed scrap metal waste powder and sewage sludge ash.

PubMed

Wang, Kuen-Sheng; Chiou, Ing-Jia

2004-10-01

The porous properties and pozzolanic effects of sewage sludge ash (SSA) make it possible to produce lightweight materials. This study explored the effects of different metallic foaming agents, made from waste aluminium products, on the foaming behaviours and engineering characteristics, as well as the microstructure of sewage sludge ash foamed lightweight materials. The results indicated that aluminium powder and mixed scrap metal waste powder possessed similar chemical compositions. After proper pre-treatment, waste aluminium products proved to be ideal substitutes for metallic foaming agents. Increasing the amount of mixed scrap metal waste by 10-15% compared with aluminium powder would produce a similar foaming ratio and compressive strength. The reaction of the metallic foaming agents mainly produced pores larger than 10 microm, different from the hydration reaction of cement that produced pores smaller than 1 microm mostly. To meet the requirements of the lightweight materials characteristics and the compressive strength, the amount of SSA could be up to 60-80% of the total solids. An adequate amount of aluminium powder is 0.5-0.9% of the total solids. Increasing the fineness of the mixed scrap metal waste powder could effectively reduce the amount required and improve the foaming ratio.

Anxiolytic-Like Actions of Fatty Acids Identified in Human Amniotic Fluid

PubMed Central

García-Ríos, Rosa Isela; Rodríguez-Landa, Juan Francisco; Contreras, Carlos M.

2013-01-01

Eight fatty acids (C12–C18) were previously identified in human amniotic fluid, colostrum, and milk in similar proportions but different amounts. Amniotic fluid is well known to be the natural environment for development in mammals. Interestingly, amniotic fluid and an artificial mixture of fatty acids contained in amniotic fluid produce similar anxiolytic-like actions in Wistar rats. We explored whether the lowest amount of fatty acids contained in amniotic fluid with respect to colostrum and milk produces such anxiolytic-like effects. Although a trend toward a dose-response effect was observed, only an amount of fatty acids that was similar to amniotic fluid fully mimicked the effect of diazepam (2 mg/kg, i.p.) in the defensive burying test, an action devoid of effects on locomotor activity and motor coordination. Our results confirm that the amount of fatty acids contained in amniotic fluid is sufficient to produce anxiolytic-like effects, suggesting similar actions during intrauterine development. PMID:23737729

Formation kinetics of furfuryl alcohol in a coffee model system.

PubMed

Albouchi, Abdullatif; Murkovic, Michael

2018-03-15

The production of furfuryl alcohol from green coffee during roasting and the effect of multiple parameters on its formation were studied employing HPLC-DAD. Results show that coffee produces furfuryl alcohol in larger quantities (418µg/g) compared to other beans or seeds (up to 132µg/g) roasted under the same conditions. The kinetics of furfuryl alcohol production resemble those of other process contaminants (e.g., HMF, acrylamide) produced in coffee roasting, with temperature and time of roasting playing significant roles in quantities formed. Different coffee species yielded different amounts of furfuryl alcohol. The data point out that the amounts of furfuryl alcohol found in roasted coffee do not reflect the total amounts produced during roasting because great amounts of furfuryl alcohol (up to 57%) are evaporating and released to the atmosphere during roasting. Finally the effect of the moisture content on furfuryl alcohol formation was found to be of little impact. Copyright © 2017 Elsevier Ltd. All rights reserved.

DEVELOPMENT OF MICROORGANISMS WITH IMPROVED TRANSPORT AND BIOSURFACTANT ACTIVITY FOR ENHANCED OIL RECOVERY

DOE Office of Scientific and Technical Information (OSTI.GOV)

M.J. McInerney; R.M. Knapp; D.P. Nagle, Jr.

2003-06-26

Biosurfactants enhance hydrocarbon biodegradation by increasing apparent aqueous solubility or affecting the association of the cell with poorly soluble hydrocarbon. Here, we show that a lipopeptide biosurfactant produced by Bacillus mojavensis strain JF-2 mobilized substantial amounts of residual hydrocarbon from sand-packed columns when a viscosifying agent and a low molecular weight alcohol were present. The amount of residual hydrocarbon mobilized depended on the biosurfactant concentration. One pore volume of cell-free culture fluid with 900 mg/l of the biosurfactant, 10 mM 2,3-butanediol and 1000 mg/l of partially hydrolyzed polyacrylamide polymer mobilized 82% of the residual hydrocarbon. Consistent with the high residualmore » oil recoveries, we found that the bio-surfactant lowered the interfacial tension (IFT) between oil and water by nearly 2 orders of magnitude compared to typical IFT values of 28-29 mN/m. Increasing the salinity increased the IFT with or without 2,3-butanediol present. The lowest interfacial tension observed was 0.1 mN/m. The lipopeptide biosurfactant system may be effective in removing hydrocarbon contamination sources in soils and aquifers and for the recovery of entrapped oil from low production oil reservoirs. Previously, we reported that Proteose peptone was necessary for anaerobic growth and biosurfactant production by B. mojavensis JF-2. The data gathered from crude purification of the growth-enhancing factor in Proteose peptone suggested that it consisted of nucleic acids; however, nucleic acid bases, nucleotides or nucleosides did not replace the requirement for Proteose Peptone. Further studies revealed that salmon sperm DNA, herring sperm DNA, Echerichia coli DNA and synthetic DNA replaced the requirement for Proteose peptone. In addition to DNA, amino acids and nitrate were required for anaerobic growth and vitamins further improved growth. We now have a defined medium that can be used to manipulate growth and biosurfactant production. As an initial step in the search for a better biosurfactant-producing microorganism, 157 bacterial strains were screened for biosurfactant production under both aerobic and anaerobic conditions. A hundred and forty seven strains produced either equal or higher amounts of biosurfactant compared to B. mojavensis JF-2 and the 10 best strains were chosen for further study. In an attempt to increase biosurfactant production, a genetic recombination experiment was conducted by mixing germinating spores of four of the best strains with B. mojavensis JF-2. Biosurfactant production was higher with the mixed spore culture than in the cocultures containing B. mojavensis JF-2 and each of the other 4 strains or in a mixed culture containing all five strains that had not undergone genetic exchange. Four isolates were obtained from the mixed spores culture that gave higher biosurfactant production than any of the original strains. Repetitive sequence-based polymerase chain reaction analysis showed differences in the band pattern for these strains compared to the parent strains, suggesting the occurrence of genetic recombination. We have a large collection of biosurfactant-producing microorganisms and a natural mechanism to improve biosurfactant production in these organisms.« less

Solid state fermentation with lactic acid bacteria to improve the nutritional quality of lupin and soya bean.

PubMed

Bartkiene, Elena; Krungleviciute, Vita; Juodeikiene, Grazina; Vidmantiene, Daiva; Maknickiene, Zita

2015-04-01

The ability of bacteriocin-like inhibitory substance (BLIS)-producing lactic acid bacteria (LAB) to degrade biogenic amines as well as to produce L(+) and D(-)-lactic acid during solid state fermentation (SSF) of lupin and soya bean was investigated. In addition, the protein digestibility and formation of organic acids during SSF of legume were investigated. Protein digestibility of fermented lupin and soya bean was found higher on average by 18.3% and 15.9%, respectively, compared to untreated samples. Tested LAB produced mainly L-lactic acid in soya bean and lupin (D/L ratio 0.38-0.42 and 0.35-0.54, respectively), while spontaneous fermentation gave almost equal amounts of both lactic acid isomers (D/L ratio 0.82-0.98 and 0.92, respectively). Tested LAB strains were able to degrade phenylethylamine, spermine and spermidine, whereas they were able to produce putrescine, histamine and tyramine. SSF improved lupin and soya bean protein digestibility. BLIS-producing LAB in lupin and soya bean medium produced a mixture of D- and L-lactic acid with a major excess of the latter isomer. Most toxic histamine and tyramine in fermented lupin and soya bean were found at levels lower those causing adverse health effects. Selection of biogenic amines non-producing bacteria is essential in the food industry to avoid the risk of amine formation. © 2014 Society of Chemical Industry.

Optimization of tetanus toxoid ammonium sulfate precipitation process using response surface methodology.

PubMed

Brgles, Marija; Prebeg, Pero; Kurtović, Tihana; Ranić, Jelena; Marchetti-Deschmann, Martina; Allmaier, Günter; Halassy, Beata

2016-10-02

Tetanus toxoid (TTd) is a highly immunogenic, detoxified form of tetanus toxin, a causative agent of tetanus disease, produced by Clostridium tetani. Since tetanus disease cannot be eradicated but is easily prevented by vaccination, the need for the tetanus vaccine is permanent. The aim of this work was to investigate the possibility of optimizing TTd purification, i.e., ammonium sulfate precipitation process. The influence of the percentage of ammonium sulfate, starting amount of TTd, buffer type, pH, temperature, and starting purity of TTd on the purification process were investigated using optimal design for response surface models. Responses measured for evaluation of the ammonium sulfate precipitation process were TTd amount (Lf/mL) and total protein content. These two parameters were used to calculate purity (Lf/mgPN) and the yield of the process. Results indicate that citrate buffer, lower temperature, and lower starting amount of TTd result in higher purities of precipitates. Gel electrophoresis combined with matrix-assisted laser desorption ionization-mass spectrometric analysis of precipitates revealed that there are no inter-protein cross-links and that all contaminating proteins have pIs similar to TTd, so this is most probably the reason for the limited success of purification by precipitation.

A toxicity assessment of hydroxyapatite nanoparticles on development and behaviour of Drosophila melanogaster

NASA Astrophysics Data System (ADS)

Pappus, S. Aurosman; Ekka, Basanti; Sahu, Swetapadma; Sabat, Debabrat; Dash, Priyabrat; Mishra, Monalisa

2017-04-01

The effects of oral intake of hydroxyapatite nanoparticles (HApNPs) were investigated on growth, development and behaviour of Drosophila. The Drosophila responses to various concentrations of HApNPs were compared. At lower concentrations, i.e. 5 mg L-1 more amount of oxidative stress was produced than that of highest concentration, i.e. 80 mg L-1. The increased amounts of oxidative stress reflect a higher amount of ROS production and increased cell damage within the larval gut. HApNPs was further shown to interfere with the calcium and phosphorus absorption pathway. Besides all these damage, HApNPs causes developmental delay in the late third instar larvae. The most significant anomaly was observed in pupae count, fly hatching after the feeding of HApNPs. Flies hatched from treated vials have decreased body weight with defective walking behaviour. Hatched flies have a phenotypic defect in the wing, eye and thorax of the bristles. Along with these changes, the adult fly becomes more prone towards stress. The findings hint that HApNPs persuade noxious effects and alter the development, structure, function and behaviour of the fly in a concentration-dependent manner.

Desalination of fish sauce by electrodialysis: effect on selected aroma compounds and amino acid compositions.

PubMed

Chindapan, Nathamol; Devahastin, Sakamon; Chiewchan, Naphaporn; Sablani, Shyam S

2011-09-01

Fish sauce is an ingredient that exhibits unique flavor and is widely used by people in Southeast Asia. Fish sauce, however, contains a significant amount of salt (sodium chloride). Recently, electrodialysis (ED) has been successfully applied to reduce salt in fish sauce; however, no information is available on the effect of ED on changes in compounds providing aroma and taste of ED-treated fish sauce. The selected aroma compounds, amino acids, and sensory quality of the ED-treated fish sauce with various salt concentrations were then analyzed. The amounts of trimethylamine, 2,6-dimethylpyrazine, phenols, and all carboxylic acids except for hexanoic acid significantly decreased, whereas benzaldehyde increased significantly when the salt removal level was higher. The amounts of all amino acids decreased with the increased salt removal level. Significant difference in flavor and saltiness intensity among ED-treated fish sauce with various salt concentrations, as assessed by a discriminative test, were observed. Information obtained in this work can serve as a guideline for optimization of a process to produce low-sodium fish sauce by ED. It also forms a basis for further in-depth sensory analysis of low-sodium fish sauce. © 2011 Institute of Food Technologists®

Use of bottom ash from olive pomace combustion in the production of eco-friendly fired clay bricks.

PubMed

Eliche-Quesada, D; Leite-Costa, J

2016-02-01

Olive pomace bottom ash was used to replace different amounts (10-50wt%) of clay in brick manufacturing. The aim of this study is both studying bricks properties and showing a new way of olive pomace bottom ash recycling. Properties of waste bricks were compared to conventional products following standard procedures in order to determine the maximum waste percentage. The amount of olive pomace bottom ash is limited to 20wt%, obtaining bricks with superior engineering properties when 10wt% of waste is added. Adding higher amount of waste (30-50wt%) resulted in bricks with water absorption and compressive strength values on the edge of meeting those established by standards. Therefore, the addition of 10 and 20wt% of olive pomace bottom ash produced bricks with a bulk density of 1635 and 1527kg/m(3) and a compressive strength of 33.9MPa and 14.2MPa, respectively. Fired bricks fulfil standards requirements for clay masonry units, offering, at the same time, better thermal insulation of buildings due to a reduction in thermal conductivity of 14.4% and 16.8% respectively, compared to control bricks (only clay). Copyright © 2015 Elsevier Ltd. All rights reserved.

Mask data processing in the era of multibeam writers

NASA Astrophysics Data System (ADS)

Abboud, Frank E.; Asturias, Michael; Chandramouli, Maesh; Tezuka, Yoshihiro

2014-10-01

Mask writers' architectures have evolved through the years in response to ever tightening requirements for better resolution, tighter feature placement, improved CD control, and tolerable write time. The unprecedented extension of optical lithography and the myriad of Resolution Enhancement Techniques have tasked current mask writers with ever increasing shot count and higher dose, and therefore, increasing write time. Once again, we see the need for a transition to a new type of mask writer based on massively parallel architecture. These platforms offer a step function improvement in both dose and the ability to process massive amounts of data. The higher dose and almost unlimited appetite for edge corrections open new windows of opportunity to further push the envelope. These architectures are also naturally capable of producing curvilinear shapes, making the need to approximate a curve with multiple Manhattan shapes unnecessary.

Gold leaf counter electrodes for dye-sensitized solar cells

NASA Astrophysics Data System (ADS)

Shimada, Kazuhiro; Toyoda, Takeshi

2018-03-01

In this study, a gold leaf 100 nm thin film is used as the counter electrode in dye-sensitized solar cells. The traditional method of hammering gold foil to obtain a thin gold leaf, which requires only small amounts of gold, was employed. The gold leaf was then attached to the substrate using an adhesive to produce the gold electrode. The proposed approach for fabricating counter electrodes is demonstrated to be facile and cost-effective, as opposed to existing techniques. Compared with electrodes prepared with gold foil and sputtered gold, the gold leaf counter electrode demonstrates higher catalytic activity with a cobalt-complex electrolyte and higher cell efficiency. The origin of the improved performance was investigated by surface morphology examination (scanning electron microscopy), various electrochemical analyses (cyclic voltammetry, linear sweep voltammetry, and electrochemical impedance spectroscopy), and crystalline analysis (X-ray diffractometry).

Correlation of Streptococcus mutans and Streptococcus sanguinis colonization and ex vivo hydrogen peroxide production in carious lesion-free and high caries adults.

PubMed

Giacaman, Rodrigo A; Torres, Sebastián; Gómez, Yenifer; Muñoz-Sandoval, Cecilia; Kreth, Jens

2015-01-01

This study was conducted to estimate oral colonization by Streptococcus mutans and Streptococcus sanguinis in adults with high and without any caries experience. Furthermore, differences in the amount of hydrogen peroxide (H2O2) produced by S. sanguinis isolated from both groups were assessed. Forty adults were divided into: (i) carious lesion-free, without any carious lesion, assessed by the International Caries Detection and Assessment System (ICDAS), or restoration, (CF) and (ii) high caries experience (HC). Saliva samples were collected and seeded on respective agar-plates for enumeration of total streptococci, S. mutans and S. sanguinis (CFU/mL) and compared between groups. Additionally, S. sanguinis colonies obtained from both groups were inoculated on Prussian blue agar for H2O2 detection. Production of H2O2 was quantified and compared between the two groups. S. sanguinis counts were significantly higher in CF than HC individuals (p<0.05). Conversely, S. mutans showed significantly higher levels in HC than CF subjects (p<0.001). S. sanguinis colonies from CF individuals produced significantly larger H2O2 halos compared with HC subjects. S. sanguinis predominates over S. mutans in saliva of adults without caries experience. In those people, S. sanguinis produces more H2O2ex vivo. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fatty Acid Composition as a Predictor for the Oxidation Stability of Korean Vegetable Oils with or without Induced Oxidative Stress

PubMed Central

Yun, Jung-Mi; Surh, Jeonghee

2012-01-01

This study was designed to investigate whether the fatty acid composition could make a significant contribution to the oxidation stability of vegetable oils marketed in Korea. Ten kinds, 97 items of vegetable oils that were produced in either an industrialized or a traditional way were collected and analyzed for their fatty acid compositions and lipid oxidation products, in the absence or presence of oxidative stress. Peroxidability index (PI) calculations based on the fatty acid composition ranged from 7.10 to 111.87 with the lowest value found in olive oils and the highest in perilla oils. In the absence of induced oxidative stress, malondialdehyde (MDA), the secondary lipid oxidation product, was generated more in the oils with higher PI (r=0.890), while the tendency was not observed when the oils were subjected to an oxidation-accelerating system. In the presence of the oxidative stress, the perilla oils produced in an industrialized manner generated appreciably higher amounts of MDA than those produced in a traditional way, although both types of oils presented similar PIs. The results implicate that the fatty acid compositions could be a predictor for the oxidation stability of the vegetable oils at the early stage of oil oxidation, but not for those at a later stage of oxidation. PMID:24471078

Amendment of biosolids with waste materials and lime: Effect on geoenvironmental properties and leachate production.

PubMed

Kayser, Claudia; Larkin, Tam; Singhal, Naresh

2015-12-01

Residuals from wastewater treatment operations (biosolids) were mixed with lime, fly ash, lime kiln dust, or two smelter slags to assess their efficacy as potential stabilisation agents by assessing their effects on the shear strength, compressibility, and solids content of mixtures. In addition, the minerals formed and leachate produced during stabilisation were determined. Tests were performed to explore the change of the geoenvironmental properties of the amended biosolids, while under pressure, at different scales using laboratory, pilot and field scale tests. The settlement characteristics of the amended biosolids under a range of applied pressures were determined using a consolidometer. All amended biosolids mixtures showed higher strength than the unamended biosolids, with mixtures containing a combination of 20% fly ash and 20% lime giving the highest (up to eightfold) increase in strength, and that with lime kiln dust and the smelter slags showing the lowest (up to twofold). The biosolids mixtures with only lime gave the second highest increase in strength (up to fourfold), but produced the largest amount of leachate, with higher level of dissolved calcium. The increase in strength correlated with availability of calcium oxide in the mixtures which lead to calcium carbonate formation, accompanied with higher leachate production and settlement during consolidation. Copper, nickel and zinc concentrations increased with alkaline additives and corresponded to higher pH and DOC levels. Nonetheless, concentrations were within the New Zealand regulatory limits for Class A landfills. Copyright © 2015 Elsevier Ltd. All rights reserved.

A competitive trade-off limits the selective advantage of increased antibiotic production.

PubMed

Gerardin, Ylaine; Springer, Michael; Kishony, Roy

2016-09-26

In structured environments, antibiotic-producing microorganisms can gain a selective advantage by inhibiting nearby competing species 1 . However, despite their genetic potential 2,3 , natural isolates often make only small amounts of antibiotics, and laboratory evolution can lead to loss rather than enhancement of antibiotic production 4 . Here, we show that, due to competition with antibiotic-resistant cheater cells, increased levels of antibiotic production can actually decrease the selective advantage to producers. Competing fluorescently labelled Escherichia coli colicin producers with non-producing resistant and sensitive strains on solid media, we found that although producer colonies can greatly benefit from the inhibition of nearby sensitive colonies, this benefit is shared with resistant colonies growing in their vicinity. A simple model, which accounts for such local competitive and inhibitory interactions, suggests that the advantage of producers varies non-monotonically with the amount of production. Indeed, experimentally varying the amount of production shows a peak in selection for producers, reflecting a trade-off between benefit gained by inhibiting sensitive competitors and loss due to an increased contribution to resistant cheater colonies. These results help explain the low level of antibiotic production observed for natural species and can help direct laboratory evolution experiments selecting for increased or novel production of antibiotics.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Pei-quan; Li, Leijun, E-mail: leijun.li@ualberta.ca; Zhang, Chunbo

The as-welded microstructure of laser-welded Ti-6Al-4V is characterized as a function of CO2 key-hole mode laser welding speed. Martensitic α′ is the predominant phase, with some α and retained β. Phase transformation is affected by the cooling rate through laser welding speed. A higher welding speed of 1.6 to 2.0 m/min produced more martensite α′ and less retained β in the welds. 1.4 m/min welding speed produced small amounts of α, besides the martensite α′. A trace of δ titanium hydride phase seems to have formed in the weld fusion zone. Moiré fringes are a common feature in the TEMmore » microstructure, due to abundance of multi-phase interfaces. Tensile twins and clusters of dislocations indicate that plastic deformation has happened in the as-welded microstructure, indicating the local stress levels to be approaching the yield stress on-cooling during laser welding.« less

[Influence of personal attitude of the manager on antibiotic use in pig production].

PubMed

Malik, J; Kaufmann, G; Hirsiger, P; Kümmerlen, D; Arnold, C; Spring, P; Sidler, X

2015-12-01

The attitude as well as the expertise of a person affect the behavior and actions in daily life. To investigate the influence of attitude and knowledge of pig producers on the use of antibiotics in farms, 220 Swiss pig producers were questioned on health awareness, attitude towards sustainable production, risk behavior, intrinsic motivation and knowledge about antibiotics and resistance development. In addition, the strategy of antibiotic use (therapeutic or prophylactic) and the business practice (single or group therapy) for the amount of antibiotics on one hand and for the risk of antibiotic resistance development on the other hand, were determined in a personal interview. Farmers using antibiotics only therapeutically had a better business practice. A direct link between the personal attitude and the antibiotic use or a higher risk of development of antibiotic resistance was not found in this investigation.

Pre-fermentation addition of grape tannin increases the varietal thiols content in wine.

PubMed

Larcher, Roberto; Tonidandel, Loris; Román Villegas, Tomás; Nardin, Tiziana; Fedrizzi, Bruno; Nicolini, Giorgio

2015-01-01

The recent finding that grape tannin may contain significant amount of S-glutathionylated (GSH-3MH) and S-cysteinylated (Cys-3MH) precursors of the varietal thiols 3-mercapto-1-hexanol and 3-mercaptohexyl acetate, characteristic of Sauvignon blanc wines, offers new opportunities for enhancing the tropical aroma in fermented beverages. In this study this new hypothesis was investigated: Müller Thurgau (17 samples) and Sauvignon blanc (15 samples) grapes were fermented with and without addition of a selected grape tannin. As expected, the tannin-added juices were higher in precursors, and they produced wines with increased free thiols. Preliminary informal sensory tests confirmed that in particular the Sauvignon wines produced with the tannin addition were often richer with increased "fruity/green" notes than the corresponding reference wines. This outcome confirms that grape tannin addition prior to fermentation can fortify the level of these compounds. Copyright © 2014 Elsevier Ltd. All rights reserved.

Synthesis of gold structures by gold-binding peptide governed by concentration of gold ion and peptide.

PubMed

Kim, Jungok; Kim, Dong-Hun; Lee, Sylvia J; Rheem, Youngwoo; Myung, Nosang V; Hur, Hor-Gil

2016-08-01

Although biological synthesis methods for the production of gold structures by microorganisms, plant extracts, proteins, and peptide have recently been introduced, there have been few reports pertaining to controlling their size and morphology. The gold ion and peptide concentrations affected on the size and uniformity of gold plates by a gold-binding peptide Midas-11. The higher concentration of gold ions produced a larger size of gold structures reached 125.5 μm, but an increased amount of Midas-11 produced a smaller size of gold platelets and increased the yield percentage of polygonal gold particles rather than platelets. The mechanisms governing factors controlling the production of gold structures were primarily related to nucleation and growth. These results indicate that the synthesis of gold architectures can be controlled by newly isolated and substituted peptides under different reaction conditions.

Stability of sonicated aqueous suspensions of phospholipids under air.

PubMed

Almog, R; Forward, R; Samsonoff, C

1991-12-01

The stability of phospholipids in liposomal aqueous suspension against oxidative degradation in air was investigated using spectrophotometric indices, glutathione peroxidase reactivity and thin layer chromatography. Zwitterionic phospholipid was found to be susceptible to degradation via oxidation of polyunsaturated hydrocarbon chains and ester hydrolysis, producing oxidized lysophosphatide and free fatty acid derivatives. These products were characterized as hydroperoxides based on their reactivity with the selenium-dependent glutathione peroxidase isolated from human erythrocytes. Lecithin in Tris buffer was more resistant to hydrolysis than in water. The sonication of 8.0 mM of soybean phosphatidylcholine (SB-PC) suspension in 0.1 M Tris (pH 7.5) in the presence of air produced relatively high concentration of conjugated diene hydroperoxide, but a small amount of hydrolyzed products. Anionic phospholipids, such as egg-phosphatidylglycerol (egg-PG), demonstrated higher resistance to air oxidation than the zwitterionic lecithin, but its oxidation was promoted by sonication.

Tantalum-tungsten oxide thermite composites prepared by sol-gel synthesis and spark plasma sintering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuntz, Joshua D.; Gash, Alexander E.; Cervantes, Octavio G.

2010-08-15

Energetic composite powders consisting of sol-gel derived nanostructured tungsten oxide were produced with various amounts of micrometer-scale tantalum fuel metal. Such energetic composite powders were ignition-tested and the results show that the powders are not sensitive to friction, spark and/or impact ignition. Initial consolidation experiments, using the High-Pressure Spark Plasma Sintering (HPSPS) technique, on the sol-gel derived nanostructured tungsten oxide produced samples with higher relative density than can be achieved with commercially available tungsten oxide. The sol-gel derived nanostructured tungsten oxide with immobilized tantalum fuel metal (Ta-WO{sub 3}) energetic composite was consolidated to a density of 9.17 g cm{sup -3}more » or 93% relative density. In addition, those samples were consolidated without significant pre-reaction of the constituents, thus retaining their stored chemical energy. (author)« less

Tantalum-Tungsten Oxide Thermite Composite Prepared by Sol-Gel Synthesis and Spark Plasma Sintering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cervantes, O; Kuntz, J; Gash, A

2009-02-13

Energetic composite powders consisting of sol-gel derived nanostructured tungsten oxide were produced with various amounts of micrometer-scale tantalum fuel metal. Such energetic composite powders were ignition tested and results show that the powders are not sensitive to friction, spark and/or impact ignition. Initial consolidation experiments, using the High Pressure Spark Plasma Sintering (HPSPS) technique, on the sol-gel derived nanostructured tungsten oxide produced samples with higher relative density than can be achieved with commercially available tungsten oxide. The sol-gel derived nanostructured tungsten oxide with immobilized tantalum fuel metal (Ta - WO{sub 3}) energetic composite was consolidated to a density of 9.17more » g.cm{sup -3} or 93% relative density. In addition those parts were consolidated without significant pre-reaction of the constituents, thus the sample retained its stored chemical energy.« less

Rising dough and baking bread at the Australian synchrotron

NASA Astrophysics Data System (ADS)

Mayo, S. C.; McCann, T.; Day, L.; Favaro, J.; Tuhumury, H.; Thompson, D.; Maksimenko, A.

2016-01-01

Wheat protein quality and the amount of common salt added in dough formulation can have a significant effect on the microstructure and loaf volume of bread. High-speed synchrotron micro-CT provides an ideal tool for observing the three dimensional structure of bread dough in situ during proving (rising) and baking. In this work, the synchrotron micro-CT technique was used to observe the structure and time evolution of doughs made from high and low protein flour and three different salt additives. These experiments showed that, as expected, high protein flour produces a higher volume loaf compared to low protein flour regardless of salt additives. Furthermore the results show that KCl in particular has a very negative effect on dough properties resulting in much reduced porosity. The hundreds of datasets produced and analysed during this experiment also provided a valuable test case for handling large quantities of data using tools on the Australian Synchrotron's MASSIVE cluster.

Microstructure Characterization and Corrosion Resistance Behavior of New Cobalt-Free Maraging Steel Produced Through ESR Techniques

NASA Astrophysics Data System (ADS)

Seikh, Asiful H.; Halfa, Hossam; Baig, Muneer; Khan, Sohail M. A.

2017-04-01

In this study, two different grades (M23 and M29) of cobalt-free low nickel maraging steel have been produced through electroslag remelting (ESR) process. The corrosion resistance of these ESR steels was investigated in 1 M H2SO4 solution using linear potentiodynamic polarization (LPP) and electrochemical impedance spectroscopy (EIS) techniques. The experiments were performed for different immersion time and solution temperature. To evaluate the corrosion resistance of the ESR steels, some significant characterization parameters from LPP and EIS curves were analyzed and compared with that of conventional C250 maraging steel. Irrespective of measurement techniques used, the results show that the corrosion resistance of the ESR steels was higher than the C250 steel. The microstructure of ESR steels was composed of uniform and well-distributed martensite accompanied with little amount of retained austenite in comparison with C250 steel.

Phytoavailability and extractability of potassium, magnesium and manganese in calcareous soil amended with olive oil wastewater.

PubMed

Gallardo-Lara, F; Azcón, M; Polo, A

2000-09-01

Land disposal of olive oil wastewater using it as a soil amendment requires a knowledge of the effects that its application may produce on the status of the mineral nutrients in the plant-soil system. A pot experiment using calcareous soil was performed in a growth chamber to examine the effects of olive oil wastewater on the availability and postharvest soil extractability of K, Mg and Mn. The experiment included 6 treatments: two rates of olive oil wastewater, two mineral fertilizer treatments containing K (which supplied K in amounts equivalent to the K supplied by the olive oil wastewater treatments), a K-free mineral fertilizer treatment, and a control. The pots were sown with ryegrass as the test plant, harvesting 3 times at intervals of one month. Olive oil wastewater has demonstrated a considerable capacity for supplying K that can be assimilated by the plant, tending in fact to surpass the mineral potassium fertilizer tested. The application of olive oil wastewater tends to reduce the concentration of Mg in the plant, similarly to the effect of adding mineral potassium fertilizer. An enhancement of Mn availability takes place in the soil amended with olive oil wastewater, which on occasion has produced Mn concentrations in plant that could be considered phytotoxic or at least excessive. After harvesting, we observed an increase in the amount of exchangeable K in soil with added industrial wastewater. However, these increases are lower than those in soil treated with mineral potassium fertilizer. The levels of exchangeable, carbonate-bound, organic-bound and residual Mg in soil were higher in treatments incorporating olive oil wastewater than in those with added mineral K, with the opposite tendency occurring in the amount of Fe-Mn oxides-bound Mg in soil. Treatments based on olive oil wastewater, especially in high doses, increased the amount of exchangeable and carbonate-bound Mn in soil, in comparison with treatments adding mineral fertilizers with or without K. In contrast, the addition of industrial wastewater caused a drop in the amount of Fe-Mn oxides-bound and organic-bound Mn in soil.

CUSTOM OPTIMIZATION OF INTRAOCULAR LENS ASPHERICITY

PubMed Central

Koch, Douglas D.; Wang, Li

2007-01-01

Purpose To investigate the optimal amount of ocular spherical aberration (SA) in an intraocular lens (IOL) to maximize optical quality. Methods In 154 eyes of 94 patients aged 40 to 80 years, implantation of aspheric IOLs was simulated with different amounts of SA to produce residual ocular SA from −0.30 μm to +0.30 μm. Using the VOL-CT program (Sarver & Associates, Carbondale, Illinois), corneal wavefront aberrations up to 6th order were computed from corneal topographic elevation data (Humphrey Atlas, Carl Zeiss Meditec, Inc, Dublin, California). Using the ZernikeTool program (Advanced Medical Optics, Inc, Santa Ana, California), the polychromatic point spread function with Stiles-Crawford effect was calculated for the residual ocular higher-order aberrations (HOAs, 3rd to 6th order, 6-mm pupil), assuming fully corrected 2nd-order aberrations. Five parameters were used to quantify optical image quality, and we determined the residual ocular SA at which the maximal image quality was achieved for each eye. Stepwise multiple regression analysis was performed to assess the predictors for optimal SA of each eye. Results The optimal SA varied widely among eyes. Most eyes had best image quality with low amounts of negative SA. For modulation transfer function volume up to 15 cycles/degree, the amount of optimal SA could be predicted based on other HOAs of the cornea with coefficient of multiple determination (R2) of 79%. Eight Zernike terms significantly contributed to the optimal SA in this model; the order of importance to optimal SA from most to least was: Z60, Z62, Z42, Z53, Z64, Z3−1, Z33, and Z31. For the other 4 measures of visual quality, the coefficients of determination varied from 32% to 63%. Conclusion The amount of ocular SA producing best image quality varied widely among subjects and could be predicted based on corneal HOAs. Selection of an aspheric IOL should be customized according to the full spectrum of corneal HOAs and not 4th-order SA alone. PMID:18427592

Clinical Trial with Sodium 99mTc-Pertechnetate Produced by a Medium-Energy Cyclotron: Biodistribution and Safety Assessment in Patients with Abnormal Thyroid Function.

PubMed

Selivanova, Svetlana V; Lavallée, Éric; Senta, Helena; Caouette, Lyne; McEwan, Alexander J B; Guérin, Brigitte; Lecomte, Roger; Turcotte, Éric

2017-05-01

A single-site prospective open-label clinical study with cyclotron-produced sodium 99m Tc-pertechnetate ( 99m Tc-NaTcO 4 ) was performed in patients with indications for a thyroid scan to demonstrate the clinical safety and diagnostic efficacy of the drug and to confirm its equivalence with conventional 99m Tc-NaTcO 4 eluted from a generator. Methods: 99m Tc-NaTcO 4 was produced from enriched 100 Mo (99.815%) with a cyclotron (24 MeV; 2 h of irradiation) or supplied by a commercial manufacturer (bulk vial eluted from a generator). Eleven patients received 325 ± 29 (mean ± SD) MBq of the cyclotron-produced 99m Tc-NaTcO 4 , whereas the age- and sex-matched controls received a comparable amount of the generator-derived tracer. Whole-body and thyroid planar images were obtained for each participant. In addition to the standard-energy window (140.5 keV ± 7.5%), data were acquired in lower-energy (117 keV ± 10%) and higher-energy (170 keV ± 10%) windows. Vital signs and hematologic and biochemical parameters were monitored before and after tracer administration. Results: Cyclotron-produced 99m Tc-NaTcO 4 showed organ and whole-body distributions identical to those of conventional 99m Tc-NaTcO 4 and was well tolerated. All images led to a clear final diagnosis. The fact that the number of counts in the higher-energy window was significantly higher for cyclotron-produced 99m Tc-NaTcO 4 did not influence image quality in the standard-energy window. Image definition in the standard-energy window with cyclotron-produced 99m Tc was equivalent to that with generator-eluted 99m Tc and had no particular features allowing discrimination between the 99m Tc production methods. Conclusion: The systemic distribution, clinical safety, and imaging efficacy of cyclotron-produced 99m Tc-NaTcO 4 in humans provide supporting evidence for the use of this tracer as an equivalent for generator-eluted 99m Tc-NaTcO 4 in routine clinical practice. © 2017 by the Society of Nuclear Medicine and Molecular Imaging.

Production of liquid fuels out of plant biomass and refuse: Methods, cost, potential (in MIXED)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woick, B.; Friedrich, R.

1981-09-01

Different ways of producing biomass and its conversion into high grade fuel for vehicles are reviewed with particular reference to physical and geographical factors, pertaining in the Federal Republic of Germany (FRG). Even with the potentially small amount of biomass in the FRG, the fueling of diesel engines with rape oil or modified ethanol, which can be obtained from any cellulosic feedstock, seems to pose the fewest difficulties and promises greatest efficiency. However, the amount of fuel produced from biomass can probably only meet a very small percentage of the total amount required.

Method to separate and determine the amount of ejecta produced in a second-shock material-fragmentation event

NASA Astrophysics Data System (ADS)

Buttler, W. T.; Hixson, R. S.; King, N. S. P.; Olson, R. T.; Rigg, P. A.; Zellner, M. B.; Routley, N.; Rimmer, A.

2007-04-01

The authors consider a mathematical method to separate and determine the amount of ejecta produced in a second-shock material-fragmentation process. The technique is theoretical and assumes that a material undergoing a shock release at a vacuum interface ejects particulate material or fragments as the initial shock unloads and reflects at the vacuum-surface interface. In this case it is thought that the reflected shock may reflect again at the source of the shock and return to the vacuum-surface interface and eject another amount of fragments or particulate material.

Infective Juveniles of the Entomopathogenic Nematode, Steinernema feltiae Produce Cryoprotectants in Response to Freezing and Cold Acclimation

PubMed Central

Ali, Farman; Wharton, David A.

2015-01-01

Steinernema feltiae is a moderately freeze-tolerant entomopathogenic nematode which survives intracellular freezing. We have detected by gas chromatography that infective juveniles of S. feltiae produce cryoprotectants in response to cold acclimation and to freezing. Since the survival of this nematode varies with temperature, we analyzed their cryoprotectant profiles under different acclimation and freezing regimes. The principal cryoprotectants detected were trehalose and glycerol with glucose being the minor component. The amount of cryoprotectants varied with the temperature and duration of exposure. Trehalose was accumulated in higher concentrations when nematodes were acclimated at 5°C for two weeks whereas glycerol level decreased from that of the non-acclimated controls. Nematodes were seeded with a small ice crystal and held at -1°C, a regime that does not produce freezing of the nematodes but their bodies lose water to the surrounding ice (cryoprotective dehydration). This increased the levels of both trehalose and glycerol, with glycerol reaching a higher concentration than trehalose. Nematodes frozen at -3°C, a regime that produces freezing of the nematodes and results in intracellular ice formation, had elevated glycerol levels while trehalose levels did not change. Steinernema feltiae thus has two strategies of cryoprotectant accumulation: one is an acclimation response to low temperature when the body fluids are in a cooled or supercooled state and the infective juveniles produce trehalose before freezing. During this process a portion of the glycerol is converted to trehalose. The second strategy is a rapid response to freezing which induces the production of glycerol but trehalose levels do not change. These low molecular weight compounds are surmised to act as cryoprotectants for this species and to play an important role in its freezing tolerance. PMID:26509788

Comparing fixed-amount and progressive-amount DRO Schedules for tic suppression in youth with chronic tic disorders.

PubMed

Capriotti, Matthew R; Turkel, Jennifer E; Johnson, Rachel A; Espil, Flint M; Woods, Douglas W

2017-01-01

Chronic tic disorders (CTDs) involve motor and/or vocal tics that often cause substantial distress and impairment. Differential reinforcement of other behavior (DRO) schedules of reinforcement produce robust, but incomplete, reductions in tic frequency in youth with CTDs; however, a more robust reduction may be needed to affect durable clinical change. Standard, fixed-amount DRO schedules have not commonly yielded such reductions, so we evaluated a novel, progressive-amount DRO schedule, based on its ability to facilitate sustained abstinence from functionally similar behaviors. Five youth with CTDs were exposed to periods of baseline, fixed-amount DRO (DRO-F), and progressive-amount DRO (DRO-P). Both DRO schedules produced decreases in tic rate and increases in intertic interval duration, but no systematic differences were seen between the two schedules on any dimension of tic occurrence. The DRO-F schedule was generally preferred to the DRO-P schedule. Possible procedural improvements and other future directions are discussed. © 2016 Society for the Experimental Analysis of Behavior.

Selective fermentation of pitted dates by S. cerevisiae for the production of concentrated fructose syrups and ethanol

NASA Astrophysics Data System (ADS)

Dharma Putra, Meilana; Abasaeed, Ahmed E.; Zeinelabdeen, Mohamed A.; Gaily, Mohamed H.; Sulieman, Ashraf K.

2014-04-01

About half of worldwide production of dates is unconsumed. Dates contain over 75 % reduced sugars (mostly glucose and fructose with nearly equal amount). Compared to the commercial Saccharomyces cerevisiae wild strain, the strains ATCC 36858 and 36859 could produce high concentration fructose syrups. The fructose fractions obtained were 95.9 and 97.4% for ATCC 36858 and 86.5 and 91.4% for ATCC 36859 at 30 and 33°C, respectively. Fructose yields higher than 90% were obtained using ATCC 36858 compared to those obtained using ATCC 36859 which were 87.3 and 66.1% at 30 and 33°C, respectively. The ethanol yield using ATCC 36858 was higher than that using ATCC 36859 by 16 and 9% at 30 and 33°C, respectively. Through this finding, the production of fructose and ethanol from date extract is a promising process. Moreover, the fructose fractions obtained here (about 90%) are much higher than those obtained with the commercial process, i.e. 55 % fructose syrups.

Isolation and characterization of two cellulose morphology mutants of Gluconacetobacter hansenii ATCC23769 producing cellulose with lower crystallinity

DOE PAGES

Deng, Ying; Nagachar, Nivedita; Fang, Lin; ...

2015-03-19

Gluconacetobacter hansenii, a Gram-negative bacterium, produces and secrets highly crystalline cellulose into growth medium, and has long been used as a model system for studying cellulose synthesis in higher plants. Cellulose synthesis involves the formation of β-1,4 glucan chains via the polymerization of glucose units by a multi-enzyme cellulose synthase complex (CSC). These glucan chains assemble into ordered structures including crystalline microfibrils. AcsA is the catalytic subunit of the cellulose synthase enzymes in the CSC, and AcsC is required for the secretion of cellulose. However, little is known about other proteins required for the assembly of crystalline cellulose. To addressmore » this question, we visually examined cellulose pellicles formed in growth media of 763 individual colonies of G. hansenii generated via Tn5 transposon insertion mutagenesis, and identified 85 that produced cellulose with altered morphologies. X-ray diffraction analysis of these 85 mutants identified two that produced cellulose with significantly lower crystallinity than wild type. The gene disrupted in one of these two mutants encoded a lysine decarboxylase and that in the other encoded an alanine racemase. Solid-state NMR analysis revealed that cellulose produced by these two mutants contained increased amounts of non-crystalline cellulose and monosaccharides associated with non-cellulosic polysaccharides as compared to the wild type. Monosaccharide analysis detected higher percentages of galactose and mannose in cellulose produced by both mutants. Field emission scanning electron microscopy showed that cellulose produced by the mutants was unevenly distributed, with some regions appearing to contain deposition of non-cellulosic polysaccharides; however, the width of the ribbon was comparable to that of normal cellulose. As both lysine decarboxylase and alanine racemase are required for the integrity of peptidoglycan, we propose a model for the role of peptidoglycan in the assembly of crystalline cellulose.« less

Isolation and characterization of two cellulose morphology mutants of Gluconacetobacter hansenii ATCC23769 producing cellulose with lower crystallinity.

PubMed

Deng, Ying; Nagachar, Nivedita; Fang, Lin; Luan, Xin; Catchmark, Jeffrey M; Tien, Ming; Kao, Teh-hui

2015-01-01

Gluconacetobacter hansenii, a Gram-negative bacterium, produces and secrets highly crystalline cellulose into growth medium, and has long been used as a model system for studying cellulose synthesis in higher plants. Cellulose synthesis involves the formation of β-1,4 glucan chains via the polymerization of glucose units by a multi-enzyme cellulose synthase complex (CSC). These glucan chains assemble into ordered structures including crystalline microfibrils. AcsA is the catalytic subunit of the cellulose synthase enzymes in the CSC, and AcsC is required for the secretion of cellulose. However, little is known about other proteins required for the assembly of crystalline cellulose. To address this question, we visually examined cellulose pellicles formed in growth media of 763 individual colonies of G. hansenii generated via Tn5 transposon insertion mutagenesis, and identified 85 that produced cellulose with altered morphologies. X-ray diffraction analysis of these 85 mutants identified two that produced cellulose with significantly lower crystallinity than wild type. The gene disrupted in one of these two mutants encoded a lysine decarboxylase and that in the other encoded an alanine racemase. Solid-state NMR analysis revealed that cellulose produced by these two mutants contained increased amounts of non-crystalline cellulose and monosaccharides associated with non-cellulosic polysaccharides as compared to the wild type. Monosaccharide analysis detected higher percentages of galactose and mannose in cellulose produced by both mutants. Field emission scanning electron microscopy showed that cellulose produced by the mutants was unevenly distributed, with some regions appearing to contain deposition of non-cellulosic polysaccharides; however, the width of the ribbon was comparable to that of normal cellulose. As both lysine decarboxylase and alanine racemase are required for the integrity of peptidoglycan, we propose a model for the role of peptidoglycan in the assembly of crystalline cellulose.

Isolation and Characterization of Two Cellulose Morphology Mutants of Gluconacetobacter hansenii ATCC23769 Producing Cellulose with Lower Crystallinity

PubMed Central

Deng, Ying; Nagachar, Nivedita; Fang, Lin; Luan, Xin; Catchmark, Jeffrey M.; Tien, Ming; Kao, Teh-hui

2015-01-01

Gluconacetobacter hansenii, a Gram-negative bacterium, produces and secrets highly crystalline cellulose into growth medium, and has long been used as a model system for studying cellulose synthesis in higher plants. Cellulose synthesis involves the formation of β-1,4 glucan chains via the polymerization of glucose units by a multi-enzyme cellulose synthase complex (CSC). These glucan chains assemble into ordered structures including crystalline microfibrils. AcsA is the catalytic subunit of the cellulose synthase enzymes in the CSC, and AcsC is required for the secretion of cellulose. However, little is known about other proteins required for the assembly of crystalline cellulose. To address this question, we visually examined cellulose pellicles formed in growth media of 763 individual colonies of G. hansenii generated via Tn5 transposon insertion mutagenesis, and identified 85 that produced cellulose with altered morphologies. X-ray diffraction analysis of these 85 mutants identified two that produced cellulose with significantly lower crystallinity than wild type. The gene disrupted in one of these two mutants encoded a lysine decarboxylase and that in the other encoded an alanine racemase. Solid-state NMR analysis revealed that cellulose produced by these two mutants contained increased amounts of non-crystalline cellulose and monosaccharides associated with non-cellulosic polysaccharides as compared to the wild type. Monosaccharide analysis detected higher percentages of galactose and mannose in cellulose produced by both mutants. Field emission scanning electron microscopy showed that cellulose produced by the mutants was unevenly distributed, with some regions appearing to contain deposition of non-cellulosic polysaccharides; however, the width of the ribbon was comparable to that of normal cellulose. As both lysine decarboxylase and alanine racemase are required for the integrity of peptidoglycan, we propose a model for the role of peptidoglycan in the assembly of crystalline cellulose. PMID:25790428

Enhanced Oil Production by the Tropical Marine Diatom Thalassiosira Sp. Cultivated in Outdoor Photobioreactors.

PubMed

Kusumaningtyas, Pintaka; Nurbaiti, Santi; Suantika, Gede; Amran, Muhammad Bachri; Nurachman, Zeily

2017-08-01

Microalgae-derived oils have potential as a biofuel feedstock. To produce microalgal oils at a large scale, large amounts of nutrients and energy are needed to grow the algae. In this study, we evaluated three types of agricultural fertilizer (AF)-based culture media (AF1, AF2, and AF3) based on a previously published enriched seawater (ES) medium to produce biomass and oils from Thalassiosira sp. Under laboratory conditions, the highest cell productivity of Thalassiosira sp. was obtained with the AF3 medium. Thalassiosira sp. cultured in the AF3 medium produced 10.4 ± 0.9 mg L -1  day -1 oils, which is significantly higher than the 5.8 ± 0.7 mg L -1  day -1 produced in the ES medium. The higher production was due to the presence of nitrate and trace elements, both of which played roles in enhancing biomass and oil content, respectively. During cell growth, resting spores appeared inside the cells and were a marker to harvest the cells. Because of the abundant availability of sunlight in the tropics during the year, the oil production of Thalassiosira sp. in the AF3 medium was scaled up using outdoor photobioreactors under different weather conditions (rainy and dry seasons). Thalassiosira sp. produced more unsaturated fatty acids during the rainy season and produced more saturated fatty acids during the dry season. This study also demonstrated that it was possible to culture Thalassiosira sp. under outdoor conditions using a low-cost agricultural fertilizer-based culture medium (AF3 medium) to produce biodiesel feedstock with an annual production of 8.1 ± 0.4 t ha -1 during the dry season and of 23.9 ± 6.8 t ha -1 during the rainy season.

Mutagenic activity and heterocyclic amine content of the human diet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knize, M.G.; Dolbeare, F.A.; Cunningham, P.L.

1993-01-15

The mutagenic activity and the mass amount of heterocyclic amines responsible for the mutagenic activity have been measured in some cooked foods. Cooked meats are the predominant source of mutagenic activity in the diet with values ranging from 0 to 10,000 revertants per gram reported in the Ames/Salmonelia test with strain TA98. Several heterocyclic amines are present and have been quantified using solid-phase extraction followed by HPLC. Frying at higher temperatures and for longer times produces the greatest mutagenic response, and concomitantly, the largest amounts of heterocyclic amines. Most of the mutagenic activity in fried meat samples can be accountedmore » for by MelQx, DiMelQx and IQ, although other heterocylic amines are present and PHIP mutagenic activity becomes significant at higher temperatures. Non-meat products such as baked breads can also form significant mutagenic activity, particularly when overcooked. Commercially prepared hamburgers made from meat substitutes such as tofu, wheat gluten or tempeh and fried at 210{degrees}C have up to 10% of the mutagenic activity of a fried beef patty cooked under the same conditions. When detected, amounts of heterocyclic amines in fried beef patties range from a total of 0.35 ng/g for commercial beef hamburgers to 142 ng/g for a beef patty cooked over a barbecue. Dietary intake is expected to have a large range, from less than one microgram per day to over 50 micrograms per day based on current knowledge of known heterocyclic amine chemicals and heterocyclic amine-containing foods.« less

Application of multiple geochemical markers to investigate organic pollution in a dynamic coastal zone.

PubMed

Liu, Liang-Ying; Wang, Ji-Zhong; Wong, Charles S; Qiu, Jian-Wen; Zeng, Eddy Y

2013-02-01

Multiple geochemical markers, including aliphatic hydrocarbons (n-alkanes), linear alkylbenzenes (LABs), and polycyclic aromatic hydrocarbons (PAHs), were employed to relate sediment organic chemical pollution in the coastal zone off South China to socioeconomic development there. Concentrations of Σn-C(15-35) (n-alkanes with 15-35 carbon atoms), ΣLAB (sum of C(10) to C(13) LABs), and Σ(26) PAH (sum of 26 PAH compounds) ranged from 110 to 3,160, 11 to 160, and 26 to 600 ng/g, with medians of 730, 40, and 230 ng/g, respectively. Natural hydrocarbons were mainly derived from terrestrial higher plant waxes, and in minor amounts from aquatic plankton and bacteria. Compositions of LABs indicated that considerable amounts of poorly treated wastewater had been directly discharged or transported to the eastern and western coastal areas of Guangdong Province. In addition, anthropogenic hydrocarbons were derived largely from vehicular emissions and combustion of domestic coal and biomass and to a lesser extent from oil spills. Eastern and western coastal sediments contained higher levels of LABs but lower levels of PAHs than those of the Pearl River Estuary, a coastal area of the Pearl River Delta. This spatial pattern of organic pollution was consistent with chemical use patterns. The eastern and western regions of Guangdong Province are economically less developed than the Pearl River Delta region, where more domestic wastewater treatment plants have been built. However, greater amounts of energy are consumed in the latter region to produce more combustion-derived PAH contamination. Copyright © 2012 SETAC.

Preliminarily comparison of nutritional composition of some fresh and processed seafood.

PubMed

Aberoumand, Ali

2012-10-01

Processing made fish less susceptible to spoilage. Fish are rich in protein content but the protein content is reduced with processing gave a better result when long-time preservation was carried out. Aim of this study was comparison of proximate analysis of some fresh and processed seafoods. Raw materials and processed seafoods (canned mackerel tuna, frozen Sea-Bream and Pressed caviar) were obtained from different firms and analyzed. Analysis carried out according AOAC methods. Moisture, protein and fat values of tuna fish were estimated to be 51, 23.9 and 21.4%, respectively. In this study, moisture content of pressed caviar was 36%, protein content was 34.4% and fat content was 16.7%, carbohydrate and energy values were 4.9% and 316 kcal/100 g, respectively. Pressed and smoked seafoods contained lower amount of moisture but higher amounts of the other components than raw materials (p < 0.05). Canned mackerel tuna, frozen sea bream and pressed caviar also contained higher amounts of fat, carbohydrate and energy, respectively (p < 0.05) than raw material. Except canning with water, all processing technologies decreased the moisture content but increased energy values (p < 0.05) of the fish. It is concluded that processed seafoods are rich in chemical components and very nutritive. Canned tuna with salted water may be advised for low-calorie diets. Caviar pressed was one the best sea foods that was produced in Iran. Since fishes are consumed as a major protein source in food, it is very important that the protein content should not be compromised during table preparation.

Topologically guided tuning of Zr-MOF pore structures for highly selective separation of C6 alkane isomers

DOE PAGES

Wang, Hao; Dong, Xinglong; Lin, Junzhong; ...

2018-05-01

As an alternative technology to energy intensive distillations, adsorptive separation by porous solids offers lower energy cost and higher efficiency. Herein we report a topology-directed design and synthesis of a series of Zr-based metal-organic frameworks with optimized pore structure for efficient separation of C6 alkane isomers, a critical step in the petroleum refining process to produce gasoline with high octane rating. Zr 6O 4(OH) 4(bptc) 3 adsorbs a large amount of n-hexane but excluding branched isomers. The n-hexane uptake is ~70% higher than that of a benchmark adsorbent, zeolite-5A. A derivative structure, Zr 6O 4(OH) 8(H 2O) 4(abtc) 2, ismore » capable of discriminating all three C6 isomers and yielding a high separation factor for 3-methylpentane over 2,3-dimethylbutane. This property is critical for producing gasoline with further improved quality. Multicomponent breakthrough experiments provide a quantitative measure of the capability of these materials for separation of C6 alkane isomers. A detailed structural analysis reveals the unique topology, connectivity and relationship of these compounds.« less

Effects of amendment of different biochars on soil physical and biological properties related to carbon mineralization

NASA Astrophysics Data System (ADS)

Zhang, Renduo; Zhu, Shuzhi; Ouyang, Lei

2014-05-01

Biochar addition to soils potentially affects various soil properties, and these effects are dependent on biochars derived from different feedstock materials and pyrolysis processes. The objective of this study was to investigate the effects of amendment of different biochars on soil physical and biological properties. Biochars were produced with dairy manure and woodchip at temperatures of 300, 500, and 700°C, respectively. Each biochar was mixed at 5% (w/w) with a forest soil and the mixture was incubated for 180 days, during which soil physical and biological properties, and soil respiration rates were measured. Results showed that the biochar addition significantly enhanced the formation of soil macroaggregates at the early incubation time. The biochar application significantly reduced soil bulk density, increased the amount of soil organic matter, and stimulated microbial activity and soil respiration rates at the early incubation stage. Biochar applications improved water retention capacity, with stronger effects by biochars produced at higher pyrolysis temperatures. At the same suction, the soil with woodchip biochars possessed higher water content than with the dairy manure biochars. Biochar addition significantly affected the soil physical and biological properties, which resulted in different soil carbon mineralization rates.

Deletion of lactate dehydrogenase in Enterobacter aerogenes to enhance 2,3-butanediol production.

PubMed

Jung, Moo-Young; Ng, Chiam Yu; Song, Hyohak; Lee, Jinwon; Oh, Min-Kyu

2012-07-01

2,3-Butanediol is an important bio-based chemical product, because it can be converted into several C4 industrial chemicals. In this study, a lactate dehydrogenase-deleted mutant was constructed to improve 2,3-butanediol productivity in Enterobacter aerogenes. To delete the gene encoding lactate dehydrogenase, λ Red recombination method was successfully adapted for E. aerogenes. The resulting strain produced a very small amount of lactate and 16.7% more 2,3-butanediol than that of the wild-type strain in batch fermentation. The mutant and its parental strain were then cultured with six different carbon sources, and the mutant showed higher carbon source consumption and microbial growth rates in all media. The 2,3-butanediol titer reached 69.5 g/l in 54 h during fed-batch fermentation with the mutant,which was 27.4% higher than that with the parental strain.With further optimization of the medium and aeration conditions,118.05 g/l 2,3-butanediol was produced in 54 h during fed-batch fermentation with the mutant. This is by far the highest titer of 2,3-butanediol with E. aerogenes achieved by metabolic pathway engineering.

Topologically guided tuning of Zr-MOF pore structures for highly selective separation of C6 alkane isomers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Hao; Dong, Xinglong; Lin, Junzhong

As an alternative technology to energy intensive distillations, adsorptive separation by porous solids offers lower energy cost and higher efficiency. Herein we report a topology-directed design and synthesis of a series of Zr-based metal-organic frameworks with optimized pore structure for efficient separation of C6 alkane isomers, a critical step in the petroleum refining process to produce gasoline with high octane rating. Zr 6O 4(OH) 4(bptc) 3 adsorbs a large amount of n-hexane but excluding branched isomers. The n-hexane uptake is ~70% higher than that of a benchmark adsorbent, zeolite-5A. A derivative structure, Zr 6O 4(OH) 8(H 2O) 4(abtc) 2, ismore » capable of discriminating all three C6 isomers and yielding a high separation factor for 3-methylpentane over 2,3-dimethylbutane. This property is critical for producing gasoline with further improved quality. Multicomponent breakthrough experiments provide a quantitative measure of the capability of these materials for separation of C6 alkane isomers. A detailed structural analysis reveals the unique topology, connectivity and relationship of these compounds.« less

Examination of an Oligocene Lacustrine Ecosystem Using C and N Stable Isotopes

NASA Astrophysics Data System (ADS)

Schweizer, M. K.; Wooller, M. J.; Toporski, J.; Fogel, M.; Steele, A.

2003-12-01

Stable isotopes of C and N are used to reconstruct the fossil Oligocene (25.8Ma) ecosystem at Lake Enspel, Westerwald, Germany. Enspel was a steep-sided, deep maar lake with anoxic bottom waters. Upon dying, terrestrial and aquatic organisms sank into the sediment where they were colonized by bacteria. These bacteria quickly became fossilized, preserving morphological detail and large amounts of organic matter from the original macroorganism. Carbon and nitrogen are sufficiently preserved in these fossils to permit stable isotope analysis. Stable isotopic signatures identify several trophic levels, including primary producers (terrigenous and aquatic plants, diatoms), primary consumers (tadpoles, some insects), and secondary consumers (carnivores such as fish). Primary producers are associated with depleted d13C and d15N values, primary consumers such as flies are one trophic shift higher, and fish are another shift higher. Signatures for the fish species show heavy-isotope enrichment correlated with increasing length, indicating an increasingly carnivorous diet. This study marks the first attempt to reconstruct a complete fossil ecosystem using stable isotope analysis, and confirms that techniques used to study modern food webs can be applied to extinct webs as well.

High yield production of extracellular recombinant levansucrase by Bacillus megaterium.

PubMed

Korneli, Claudia; Biedendieck, Rebekka; David, Florian; Jahn, Dieter; Wittmann, Christoph

2013-04-01

In this study, a high yield production bioprocess with recombinant Bacillus megaterium for the production of the extracellular enzyme levansucrase (SacB) was developed. For basic optimization of culture parameters and nutrients, a recombinant B. megaterium reporter strain that produced green fluorescent protein under control of a vector-based xylose-inducible promoter was used. It enabled efficient microtiter plate-based screening via fluorescence analysis. A pH value of pH 6, 20 % of dissolved oxygen, 37 °C, and elevated levels of biotin (100 μg L(-1)) were found optimal with regard to high protein yield and reduced overflow metabolism. Among the different compounds tested, fructose and glycerol were identified as the preferred source of carbon. Subsequently, the settings were transferred to a B. megaterium strain recombinantly producing levansucrase SacB based on the plasmid-located xylose-inducible expression system. In shake flask culture under the optimized conditions, the novel strain already secreted the target enzyme in high amounts (14 U mL(-1) on fructose and 17.2 U mL(-1) on glycerol). This was further increased in high cell density fed-batch processes up to 55 U mL(-1), reflecting a levansucrase concentration of 0.52 g L(-1). This is 100-fold more than previous efforts for this enzyme in B. megaterium and more than 10-fold higher than reported values of other extracellular protein produced in this microorganism so far. The recombinant strain could also handle raw glycerol from biodiesel industry which provided the same amount and quality of the recombinant protein and suggests future implementation into existing biorefinery concepts.

The Introduction into Bacillus sphaericus of the Bacillus thuringiensis subsp. medellin cyt1Ab1 Gene Results in Higher Susceptibility of Resistant Mosquito Larva Populations to B. sphaericus

PubMed Central

Thiéry, I.; Hamon, S.; Delécluse, A.; Orduz, S.

1998-01-01

The fragment containing the gene encoding the cytolytic Cyt1Ab1 protein from Bacillus thuringiensis subsp. medellin and its flanking sequences (I. Thiery, A. Delécluse, M. C. Tamayo, and S. Orduz, Appl. Environ. Microbiol. 63:468–473, 1997) was introduced into Bacillus sphaericus toxic strains 2362, 2297, and Iab872 by electroporation with the shuttle vector pMK3. Only small amounts of the protein were produced in recombinant strains 2362 and Iab872. The protein was detected in these strains only by Western blotting and immunodetection with antibody raised against Cyt1Ab1 protein. Large amounts of Cyt1Ab1 protein were produced in B. sphaericus recombinant strain 2297, and there was an additional crystal, other than that of the binary toxin, within the exosporium. The production of the Cyt1Ab1 protein in addition to the binary toxin did not increase the larvicidal activity of the B. sphaericus recombinant strain against susceptible mosquito populations of Culex pipiens or Aedes aegypti. However, it partially restored (10 to 20 times) susceptibility of the resistant mosquito populations of C. pipiens (SPHAE) and Culex quinquefasciatus (GeoR) to the binary toxin. The Cyt1Ab1 protein produced in recombinant B. thuringiensis SPL407(pcyt1Ab1) was synthesized in two types of crystal—one round and with various dense areas, surrounded by an envelope, and the other a regular cuboid crystal, very similar to that found in the B. sphaericus recombinant strain. PMID:9758818

The effect of clay catalyst on the chemical composition of bio-oil obtained by co-pyrolysis of cellulose and polyethylene.

PubMed

Solak, Agnieszka; Rutkowski, Piotr

2014-02-01

Cellulose/polyethylene (CPE) mixture 3:1, w/w with and without three clay catalysts (K10 - montmorillonite K10, KSF - montmorillonite KSF, B - Bentonite) addition were subjected to pyrolysis at temperatures 400, 450 and 500°C with heating rate of 100°C/s to produce bio-oil with high yield. The pyrolytic oil yield was in the range of 41.3-79.5 wt% depending on the temperature, the type and the amount of catalyst. The non-catalytic fast pyrolysis at 500°C gives the highest yield of bio-oil (79.5 wt%). The higher temperature of catalytic pyrolysis of cellulose/polyethylene mixture the higher yield of bio-oil is. Contrarily, increasing amount of montmorillonite results in significant, almost linear decrease in bio-oil yield followed by a significant increase of gas yield. The addition of clay catalysts to CPE mixture has a various influence on the distribution of bio-oil components. The addition of montmorillonite K10 to cellulose/polyethylene mixture promotes the deepest conversion of polyethylene and cellulose. Additionally, more saturated than unsaturated hydrocarbons are present in resultant bio-oils. The proportion of liquid hydrocarbons is the highest when a montmorillonite K10 is acting as a catalyst. Copyright © 2013 Elsevier Ltd. All rights reserved.

Supply of Fatty Acid Is One Limiting Factor in the Accumulation of Triacylglycerol in Developing Embryos1

PubMed Central

Bao, Xiaoming; Ohlrogge, John

1999-01-01

The metabolic factors that determine oil yield in seeds are still not well understood. To begin to examine the limits on triacylglycerol (TAG) production, developing Cuphea lanceolata, Ulmus carpinifolia, and Ulmus parvifolia embryos were incubated with factors whose availability might limit oil accumulation. The addition of glycerol or sucrose did not significantly influence the rate of TAG synthesis. However, the rate of 14C-TAG synthesis upon addition of 2.1 mm 14C-decanoic acid (10:0) was approximately four times higher than the in vivo rate of TAG accumulation in C. lanceolata and two times higher than the in vivo rate in U. carpinifolia and U. parvifolia. In C. lanceolata embryos, the highest rate of 14C-TAG synthesis (14.3 nmol h−1 embryo−1) was achieved with the addition of 3.6 mm decanoic acid. 14C-Decanoic acid was incorporated equally well in all three acyl positions of TAG. The results suggest that C. lanceolata, U. carpinifolia, and U. parvifolia embryos have sufficient acyltransferase activities and glycerol-3-phosphate levels to support rates of TAG synthesis in excess of those found in vivo. Consequently, the amount of TAG synthesized in these oilseeds may be in part determined by the amount of fatty acid produced in plastids. PMID:10444089

Supply of fatty acid is one limiting factor in the accumulation of triacylglycerol in developing embryos

PubMed

Bao; Ohlrogge

1999-08-01

The metabolic factors that determine oil yield in seeds are still not well understood. To begin to examine the limits on triacylglycerol (TAG) production, developing Cuphea lanceolata, Ulmus carpinifolia, and Ulmus parvifolia embryos were incubated with factors whose availability might limit oil accumulation. The addition of glycerol or sucrose did not significantly influence the rate of TAG synthesis. However, the rate of (14)C-TAG synthesis upon addition of 2.1 mM (14)C-decanoic acid (10:0) was approximately four times higher than the in vivo rate of TAG accumulation in C. lanceolata and two times higher than the in vivo rate in U. carpinifolia and U. parvifolia. In C. lanceolata embryos, the highest rate of (14)C-TAG synthesis (14.3 nmol h(-1) embryo(-1)) was achieved with the addition of 3.6 mM decanoic acid. (14)C-Decanoic acid was incorporated equally well in all three acyl positions of TAG. The results suggest that C. lanceolata, U. carpinifolia, and U. parvifolia embryos have sufficient acyltransferase activities and glycerol-3-phosphate levels to support rates of TAG synthesis in excess of those found in vivo. Consequently, the amount of TAG synthesized in these oilseeds may be in part determined by the amount of fatty acid produced in plastids.

Zinc treatment increases the titre of 'Candidatus Liberibacter asiaticus' in huanglongbing-affected citrus plants while affecting the bacterial microbiomes.

PubMed

Zhang, M Q; Guo, Y; Powell, C A; Doud, M S; Yang, C Y; Zhou, H; Duan, Y P

2016-06-01

Huanglongbing (HLB)-affected citrus often display zinc deficiency symptoms. In this study, supplemental zinc was applied to citrus to determine its effect on Candidatus Liberibacter asiaticus (Las) titre, HLB symptoms, and leaf microbiome. HLB-affected citrus were treated with various amounts of zinc. The treatments promoted Las growth and affected microbiomes in citrus leaves. Phylochip(™) -based results indicated that 5475 of over 50 000 known Operational Taxonomic Units (OTUs) in 52 phyla were detected in the midribs of HLB-affected citrus, of which Proteobacteria was the most abundant, followed by Firmicutes and Actinobacteria. In comparison, the microbiomes of zinc-treated diseased plants had overall more OTUs with higher amounts of Proteobacteria, but decreased percentages of Firmicutes and Actinobacteria. In addition, more OTUs of siderophore-producing bacteria were present. Only zinc-sensitive Staphylococcaceae had higher OTU's in the diseased plants without zinc treatments. Although HLB-affected citrus appear zinc deficient, zinc amendments increased the pathogen levels and shifted the microbiome. HLB is currently the most devastating disease of citrus worldwide. Zinc is often applied to HLB-affected citrus due to zinc deficiency symptoms. This study provided new insights into the potential effects of zinc on HLB and the microbial ecology of citrus. © 2016 The Society for Applied Microbiology.

Human self-control and the density of reinforcement

PubMed Central

Flora, Stephen R.; Pavlik, William B.

1992-01-01

Choice responding in adult humans on a discrete-trial button-pressing task was examined as a function of amount, delay, and overall density (points per unit time) of reinforcement. Reinforcement consisted of points that were exchangeable for money. In T 0 conditions, an impulsive response produced 4 points immediately and a self-control response produced 10 points after a delay of 15 s. In T 15 conditions, a constant delay of 15 s was added to both prereinforcer delays. Postreinforcer delays, which consisted of 15 s added to the end of each impulsive trial, equated trial durations regardless of choice, and was manipulated in both T 0 and T 15 conditions. In all conditions, choice was predicted directly from the relative reinforcement densities of the alternatives. Self-control was observed in all conditions except T 0 without postreinforcer delays, where the impulsive choices produced the higher reinforcement density. These results support previous studies showing that choice is a direct function of the relative reinforcement densities when conditioned (point) reinforcers are used. In contrast, where responding produces intrinsic (immediately consumable) reinforcers, immediacy of reinforcement appears to account for preference when density does not. PMID:16812652

On-site production of crude glucoamylase for kitchen waste hydrolysis.

PubMed

Wang, Xiao Qiang; Wang, Qun Hui; Liu, Ying Ying; Ma, Hong Zhi

2010-06-01

Kitchen waste from dining rooms accounts for a considerable proportion of municipal solid garbage, and economical recycle ways are needed to be developed. This study investigated glucoamylase production from kitchen waste and the feasibility of kitchen waste hydrolysis by the crude enzymes produced. The key problems of high water content and poor porosity in kitchen waste for glucoamylase production under solid-state fermentation could be solved readily by the addition of corn stover or paddy husk. As a support medium, corn stover was better than paddy husk. Smashed kitchen waste (sKW) mixed with corn stover in the ratio of 3.75 : 1 (dry basis) produced 1838 U g(-1) of glucoamylase by Aspergillus niger UV-60 within 96 h. The enzyme productivity from kitchen waste was over two-fold higher than that from wheat bran with additional nutrients. Without any recovery treatment, the produced glucoamylase could be used directly to hydrolyse sKW slurry. The optimum enzyme dose 8% (crude enzyme/kichen waste, w/w) was not too big, and was sufficient to hydrolyse 10% (dry basis) sKW slurry to produce a maximum amount of reducing sugar of 55.4 g L(-1).

Chemical Changes during Maize Tissue Aging and Its Relationship with Mediterranean Corn Borer Resistance.

PubMed

López-Malvar, Ana; Ordás, Bernardo; Souto, Carlos; Encina, Antonio; Malvar, Rosa A; Santiago, Rogelio

2017-10-25

The Mediterranean corn borer (MCB), Sesamia nonagrioides Lef, is an important pest of maize in temperate areas, causing significant stalk lodging and yield losses. The main goals of this study were to determine possible changes in chemical traits (phenols, flavonoids, anthocyanins, sugars, fibers, and lignin) during plant development after the flowering stage and to assess how those traits may differ in diverse genotypes of maize, such as MCB resistant and susceptible. Higher values for some particular traits in more mature tissues seemed to increase their effectiveness against the MCB attack. A decreased amount of borer damage in the field was recorded in the resistant inbred line and in older tissues (7.90 cm vs 31.70 cm as the mean for the stalk tunnel length). In accordance with these results, the resistant inbred line showed a higher degree of hemicellulose cross-linkage (due to ferulic and diferulic acids), higher soluble sugar content, and higher stalk strength. The use of resistant varieties and early sowings is highly recommended as an integrated approach to reduce the yield losses produced by this pest.

Survival and germination of Mediterranean grassland species after simulated sheep ingestion: ecological correlates with seed traits

NASA Astrophysics Data System (ADS)

Peco, B.; Lopez-Merino, L.; Alvir, M.

2006-09-01

Large amounts of viable seeds from Mediterranean grassland species have been found in herbivore dung; however which species produce seeds that can survive and germinate after ingestion by herbivores is still not well understood. This paper evaluates the importance of seed size, shape and coat impermeability in the endozoochorous dispersal process of 20 abundant species from central Iberian rangelands. Seed survival, germination percentages and germination speed were analysed in controlled experiments on the chewing and gut passage process by inserting seeds in the rumen of fistulated sheep, followed by simulated acid-pepsin digestion. Higher germination percentages in the control than the simulated sheep ingestion treatment were found in 75% of seeds. All species showed lower survival following the treatment, two species had a higher germination speed and five had a lower rate. Large-seeded species generally had higher survival percentages than small-seeded species. Species with impermeable seed coats had higher germination percentages following treatment although no significant differences were noted for either seed survival or germination speed.

Effects of fibre type and structure of longissimus lumborum (Ll), biceps femoris (Bf) and semimembranosus (Sm) deer muscles salting with different Nacl addition on proteolysis index and texture of dry-cured meats.

PubMed

Żochowska-Kujawska, J

2016-11-01

The aim of the present study was to describe the effect of fibre type and structure as well as NaCl level on the proteolysis index and texture parameters observed in dry-cured meats produced from individual deer muscles. The biceps femoris, semimembranosus and longissimus lumborum muscles were cut from deer main elements, shaped into blocks by trimming off the edges, cured by adding 4, 6 and 8% of salt (w/w) and dried in a ripening chamber for 29days. The results indicated that deer dry-cured muscles with higher percentage of red fibres (type I) showed higher texture parameters, proteolysis index as well as lower moisture losses than muscles with higher amount of white fibres (type IIB). Dry-cured deer muscles with lower NaCl content showed higher values of proteolysis index and lower hardness, cohesiveness, springiness, and chewiness, as well as lower changes in structure elements. Copyright © 2016. Published by Elsevier Ltd.

System for measuring film thickness

DOEpatents

Batishko, Charles R.; Kirihara, Leslie J.; Peters, Timothy J.; Rasmussen, Donald E.

1990-01-01

A system for determining the thicknesses of thin films of materials exhibiting fluorescence in response to exposure to excitation energy from a suitable source of such energy. A section of film is illuminated with a fixed level of excitation energy from a source such as an argon ion laser emitting blue-green light. The amount of fluorescent light produced by the film over a limited area within the section so illuminated is then measured using a detector such as a photomultiplier tube. Since the amount of fluorescent light produced is a function of the thicknesses of thin films, the thickness of a specific film can be determined by comparing the intensity of fluorescent light produced by this film with the intensity of light produced by similar films of known thicknesses in response to the same amount of excitation energy. The preferred embodiment of the invention uses fiber optic probes in measuring the thicknesses of oil films on the operational components of machinery which are ordinarily obscured from view.

[Effects of irrigation amount and stage on water consumption characteristics and grain yield of wheat].

PubMed

Wang, De-Mei; Yu, Zhen-Wen

2008-09-01

Field experiment was conducted in 2005 -2007 to study the effects of irrigation amount and stage on the water consumption characteristics, grain yield, and water use efficiency of wheat. The results showed that the variation coefficient of the proportion of soil water consumption amount to total water consumption amount was significantly higher than that of precipitation to total water consumption amount, suggesting the relatively wide regulation range of soil water use efficiency. The proportions of irrigation amount, precipitation, and soil water consumption amount to total water consumption amount were 31.0%, 38.9%, and 30.1% in treatment W3 (irrigated at jointing and flowering stages, with total irrigation amount of 120 mm), and 51.7%, 32.4%, and 15.9% in treatment W5 (irrigated before winter and at jointing, flowering and grain-filling stages, with total irrigation amount of 240 mm), respectively, indicating that treatment W3 had a significantly higher proportion of soil water consumption amount to total water consumption amount than treatment W5. Though treatments W2 (irrigated before winter and at jointing stage) and W3 (irrigated at jointing and flowering stages) had the same irrigation amount (120 mm), the water consumption amount during the period from flowering to maturing was significantly higher in W3 than in W2, while the water consumption amount before jointing was significantly lower in W3 than in W2. The water consumption pattern in treatment W3 was in agreement with the water requirement pattern of wheat, which was the physiological basis of high water use efficiency.

A single active trehalose-6-P synthase (TPS) and a family of putative regulatory TPS-like proteins in Arabidopsis.

PubMed

Vandesteene, Lies; Ramon, Matthew; Le Roy, Katrien; Van Dijck, Patrick; Rolland, Filip

2010-03-01

Higher plants typically do not produce trehalose in large amounts, but their genome sequences reveal large families of putative trehalose metabolism enzymes. An important regulatory role in plant growth and development is also emerging for the metabolic intermediate trehalose-6-P (T6P). Here, we present an update on Arabidopsis trehalose metabolism and a resource for further detailed analyses. In addition, we provide evidence that Arabidopsis encodes a single trehalose-6-P synthase (TPS) next to a family of catalytically inactive TPS-like proteins that might fulfill specific regulatory functions in actively growing tissues.

Potatoes in Space

NASA Technical Reports Server (NTRS)

2004-01-01

Astroculture is a suite of technologies used to produce and maintain a closed controlled environment for plant growth. The two most recent missions supported growth of potato, dwarf wheat, and mustard plants and provided scientists with the first opportunity to conduct true plant research in space. Light emitting diodes have particular usefulness for plant growth lighting because they emit a much smaller amount of radiant heat than do conventional lighting sources and because they have potential of directing a higher percentage of the emitted light onto plants surfaces. Furthermore, the high output LED's have emissions in the 600-700 nm waveband, which is of highest efficiency for photosynthesis by plants.

Wheat Under LED's (Light Emitting Diodes)

NASA Technical Reports Server (NTRS)

2004-01-01

Astroculture is a suite of technologies used to produce and maintain a closed controlled environment for plant growth. The two most recent missions supported growth of potato, dwarf wheat, and mustard plants, and provided scientists with the first opportunity to conduct true plant research in space. Light emitting diodes have particular usefulness for plant growth lighting because they emit a much smaller amount of radiant heat than do conventional lighting sources and because they have potential of directing a higher percentage of the emitted light onto plants surfaces. Furthermore, the high output LED's have emissions in the 600-700 nm waveband, which is of highest efficiency for photosynthesis by plants.

Fuel from Tobacco and Arundo Donax: Synthetic Crop for Direct Drop-in Biofuel Production through Re-routing the Photorespiration Intermediates and Engineering Terpenoid Pathways

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

PETRO Project: Biofuels offer renewable alternatives to petroleum-based fuels that reduce net greenhouse gas emissions to nearly zero. However, traditional biofuels production is limited not only by the small amount of solar energy that plants convert through photosynthesis into biological materials, but also by inefficient processes for converting these biological materials into fuels. Farm-ready, non-food crops are needed that produce fuels or fuel-like precursors at significantly lower costs with significantly higher productivity. To make biofuels cost-competitive with petroleum-based fuels, biofuels production costs must be cut in half.

Hydroquinone: O-glucosyltransferase from cultivated Rauvolfia cells: enrichment and partial amino acid sequences.

PubMed

Arend, J; Warzecha, H; Stöckigt, J

2000-01-01

Plant cell suspension cultures of Rauvolfia are able to produce a high amount of arbutin by glucosylation of exogenously added hydroquinone. A four step purification procedure using anion exchange, hydrophobic interaction, hydroxyapatite-chromatography and chromatofocusing delivered in a yield of 0.5%, an approximately 390 fold enrichment of the involved glucosyltransferase. SDS-PAGE showed a M(r) for the enzyme of 52 kDa. Proteolysis of the pure enzyme with endoproteinase LysC revealed six peptide fragments with 9-23 amino acids which were sequenced. Sequence alignment of the six peptides showed high homologies to glycosyltransferases from other higher plants.

Emission of nanoparticles during combustion of waste biomass in fireplace

NASA Astrophysics Data System (ADS)

Drastichová, Vendula; Krpec, Kamil; Horák, Jiří; Hopan, František; Kubesa, Petr; Martiník, Lubomír; Koloničný, Jan; Ochodek, Tadeáš; Holubčík, Michal

2014-08-01

Contamination of air by solid particles is serious problem for human health and also environment. Small particles in nano-sizes are more dangerous than same weight of larger size. Negative effect namely of the solid particles depends on (i) number, (ii) specific surface area (iii) respirability and (iv) bonding of others substances (e.g. PAHs, As, Cd, Zn, Cu etc.) which are higher for smaller (nano-sizes) particles compared to larger one. For this reason mentioned above this contribution deals with measuring of amount, and distribution of nanoparticles produced form combustion of waste city biomass in small combustion unit with impactor DLPI.

[Isolation, identification and fermentation optimization of Bacillus tequilensis PanD37 producing L-aspartate α- decarboxylase].

PubMed

Feng, Zhibin; Zhang, Juan; Chen, Guozhong; Cha, Yaping; Liu, Jinjie; Ge, Yihe; Cheng, Shiwei; Yu, Botao

2016-01-04

We screened bacteria producing L-aspartate α-decarboxylase from grapery soil and optimized the fermentation conditions. L-aspartate α-decarboxylase producing bacteria were screened by color-changing circle and liquid secondary screening culture media. Combination of morphological, physiological and biochemical characteristics and 16S rRNA sequence analysis were used to identify the bacteria. Fermentation conditions were optimized by single factor test and orthogonal experiment. Strain PanD37 showed high L-aspartate α-decarboxylase producing property and was identified as Bacillus tequilensis. The optimum fermentation conditions of PanD37 were liquid volume of 50 mL in 500 mL flask, 220 r/min at 35 °C, inoculation amount of 5% for 28 h with a medium of 22.5 g/L sucrose, 7.5 g/L fumaric acid, 20 g/L peptone, 6 g/L L-aspartic acid, 2 g/L Triton X-100, at initial pH of 7.0. Under the optimal fermentation conditions, the highest L-aspartate α-decarboxylase activity reached 44.57 U/mL, which was 2.57 folds higher than that obtained before optimization. Strain PanD37 was identified as Bacillus tequilensiswhich was capable of highly producing L-aspartate α-decarboxylase under the optimal fermentation conditions.

Water contamination from oil extraction activities in Northern Peruvian Amazonian rivers.

PubMed

Yusta-García, Raúl; Orta-Martínez, Martí; Mayor, Pedro; González-Crespo, Carlos; Rosell-Melé, Antoni

2017-06-01

Oil extraction activities in the Northern Peruvian Amazon have generated a long-standing socio-environmental conflict between oil companies, governmental authorities and indigenous communities, partly derived from the discharge of produced waters containing high amounts of heavy metals and hydrocarbons. To assess the impact of produced waters discharges we conducted a meta-analysis of 2951 river water and 652 produced water chemical analyses from governmental institutions and oil companies reports, collected in four Amazonian river basins (Marañon, Tigre, Corrientes and Pastaza) and their tributaries. Produced water discharges had much higher concentrations of chloride, barium, cadmium and lead than are typically found in fresh waters, resulting in the widespread contamination of the natural water courses. A significant number of water samples had levels of cadmium, barium, hexavalent chromium and lead that did not meet Peruvian and international water standards. Our study shows that spillage of produced water in Peruvian Amazon rivers placed at risk indigenous population and wildlife during several decades. Furthermore, the impact of such activities in the headwaters of the Amazon extended well beyond the boundaries of oil concessions and national borders, which should be taken into consideration when evaluating large scale anthropogenic impacts in the Amazon. Copyright © 2017 Elsevier Ltd. All rights reserved.

Identification of O-methylsterigmatocystin as an aflatoxin B1 and G1 precursor in Aspergillus parasiticus.

PubMed Central

Bhatnagar, D; McCormick, S P; Lee, L S; Hill, R A

1987-01-01

An isolate of Aspergillus parasiticus CP461 (SRRC 2043) produced no detectable aflatoxins, but accumulated O-methylsterigmatocystin (OMST). When sterigmatocystin (ST) was fed to this isolate in a low-sugar medium, there was an increase in the accumulation of OMST, without aflatoxin synthesis. When radiolabeled [14C]OMST was fed to resting mycelia of a non-aflatoxin-, non-ST-, and non-OMST-producing mutant of A. parasiticus AVN-1 (SRRC 163), 14C-labeled aflatoxins B1 and G1 were produced; 10 nmol of OMST produced 7.8 nmol of B1 and 1.0 nmol of G1, while 10 nmol of ST produced 6.4 nmol of B1 and 0.6 nmol of G1. A time course study of aflatoxin synthesis in ST feeding experiments with AVN-1 revealed that OMST is synthesized by the mold during the onset of aflatoxin synthesis. The total amount of aflatoxins recovered from OMST feeding experiments was higher than from experiments in which ST was fed to the resting mycelia. These results suggest that OMST is a true metabolite in the aflatoxin biosynthetic pathway between sterigmatocystin and aflatoxins B1 and G1 and is not a shunt metabolite, as thought previously. PMID:3111363

Influence of levan-producing acetic acid bacteria on buckwheat-sourdough breads.

PubMed

Ua-Arak, Tharalinee; Jakob, Frank; Vogel, Rudi F

2017-08-01

Buckwheat sourdoughs supplemented with molasses as natural sucrose source were fermented with levan-producing Gluconobacter (G.) albidus TMW 2.1191 and Kozakia (K.) baliensis NBRC 16680. Cell growth, concomitant levan and low-molecular-weight metabolite production were monitored. Sourdough breads were prepared with different sourdoughs from both strains (24, 30 and 48 h fermentation, respectively) and analyzed with respect to bread volume, crumb hardness and sensory characteristics. During fermentation, levan, acetic and gluconic acids were increasingly produced, while spontaneously co-growing lactic acid bacteria additionally formed acetic and lactic acids. Sourdoughs from both strains obtained upon 24 h of fermentation significantly improved the bread sensory and quality, including higher specific volume as well as lower crumb hardness. Buckwheat doughs containing isolated levan, with similar molecular size and mass compared to in situ produced levan in the sourdough at 48 h, verified the positive effect of levan on bread quality. However, the positive effects of levan were masked to a certain extent by the impact from the natural acidification during fermentations. While levan-producing acetic acid bacteria are a promising alternative for the development of clean-label gluten-free breads without the need of additives, an appropriate balance between acidification and levan production (amount and structure) must be reached. Copyright © 2017 Elsevier Ltd. All rights reserved.

Labeling tetracysteine-tagged proteins with biarsenical dyes for live cell imaging.

PubMed

Gaietta, Guido M; Deerinck, Thomas J; Ellisman, Mark H

2011-01-01

Correlation of real-time or time-lapse light microscopy (LM) with electron microscopy (EM) of cells can be performed with biarsenical dyes. These dyes fluorescently label tetracysteine-tagged proteins so that they can be imaged with LM and, upon fluorescent photoconversion of 3,3'-diaminobenzidine tetrahydrochloride (DAB), with EM as well. In the following protocol, cells expressing tetracysteine-tagged proteins are labeled for 1 h with biarsenical dyes. The volumes indicated are for a single 30-mm culture dish containing 2 mL of labeling medium. Scale the suggested volumes up or down depending upon the size of the culture dish used in the labeling. The same procedure can be adapted for longer labeling times by lowering the amount of dye used to 50-100 nM; however, the amount of the competing dithiol EDT is maintained at 10-20 μM. Longer labeling times often produce higher signal-to-noise ratios and cause less trauma to the treated cells prior to imaging.

Evaluation of hyaluronan from different sources: Streptococcus zooepidemicus, rooster comb, bovine vitreous, and human umbilical cord.

PubMed

Shiedlin, Aviva; Bigelow, Russell; Christopher, William; Arbabi, Saman; Yang, Laura; Maier, Ronald V; Wainwright, Norman; Childs, Alice; Miller, Robert J

2004-01-01

Sodium hyaluronate (HA) is widely distributed in extracellular matrixes and can play a role in orchestrating cell function. Consequently, many investigators have looked at the effect of exogenous HA on cell behavior in vitro. HA can be isolated from several sources (e.g., bacterial, rooster comb, umbilical cord) and therefore can possess diverse impurities. This current study compares the measured impurities and the differences in biological activity between HA preparations from these sources. It was demonstrated that nucleic acid and protein content was highest in human umbilical cord and bovine vitreous HA and was low in bacterial and rooster comb HA. Macrophages exposed to human umbilical cord HA produced significantly higher amounts of TNF-alpha relative to control or bacterial-derived HA. These results indicate that the source of HA should be considered due to differences in the amounts and types of contaminants that could lead to widely different behaviors in vitro and in vivo.

Minimising generation of acid whey during Greek yoghurt manufacturing.

PubMed

Uduwerella, Gangani; Chandrapala, Jayani; Vasiljevic, Todor

2017-08-01

Greek yoghurt, a popular dairy product, generates large amounts of acid whey as a by-product during manufacturing. Post-processing treatment of this stream presents one of the main concerns for the industry. The objective of this study was to manipulate initial milk total solids content (15, 20 or 23 g/100 g) by addition of milk protein concentrate, thus reducing whey expulsion. Such an adjustment was investigated from the technological standpoint including starter culture performance, chemical and physical properties of manufactured Greek yoghurt and generated acid whey. A comparison was made to commercially available products. Increasing protein content in regular yoghurt reduced the amount of acid whey during whey draining. This protein fortification also enhanced the Lb. bulgaricus growth rate and proteolytic activity. Best structural properties including higher gel strength and lower syneresis were observed in the Greek yoghurt produced with 20 g/100 g initial milk total solid compared to manufactured or commercially available products, while acid whey generation was lowered due to lower drainage requirement.

Surface plasmon resonance sensing detection of mercury and lead ions based on conducting polymer composite.

PubMed

Abdi, Mahnaz M; Abdullah, Luqman Chuah; Sadrolhosseini, Amir R; Mat Yunus, Wan Mahmood; Moksin, Mohd Maarof; Tahir, Paridah Md

2011-01-01

A new sensing area for a sensor based on surface plasmon resonance (SPR) was fabricated to detect trace amounts of mercury and lead ions. The gold surface used for SPR measurements were modified with polypyrrole-chitosan (PPy-CHI) conducting polymer composite. The polymer layer was deposited on the gold surface by electrodeposition. This optical sensor was used for monitoring toxic metal ions with and without sensitivity enhancement by chitosan in water samples. The higher amounts of resonance angle unit (ΔRU) were obtained for PPy-CHI film due to a specific binding of chitosan with Pb(2+) and Hg(2+) ions. The Pb(2+) ion bind to the polymer films most strongly, and the sensor was more sensitive to Pb(2+) compared to Hg(2+). The concentrations of ions in the parts per million range produced the changes in the SPR angle minimum in the region of 0.03 to 0.07. Data analysis was done by Matlab software using Fresnel formula for multilayer system.

Lipase of Aspergillus niger NCIM 1207: A Potential Biocatalyst for Synthesis of Isoamyl Acetate.

PubMed

Mhetras, Nutan; Patil, Sonal; Gokhale, Digambar

2010-10-01

Commercial lipase preparations and mycelium bound lipase from Aspergillus niger NCIM 1207 were used for esterification of acetic acid with isoamyl alcohol to obtain isoamyl acetate. The esterification reaction was carried out at 30°C in n-hexane with shaking at 120 rpm. Initial reaction rates, conversion efficiency and isoamyl acetate concentration obtained using Novozyme 435 were the highest. Mycelium bound lipase of A. niger NCIM 1207 produced maximal isoamyl acetate formation at an alcohol/acid ratio of 1.6. Acetic acid at higher concentrations than required for the critical alcohol/acid ratio lower than 1.3 and higher than 1.6 resulted in decreased yields of isoamyl acetate probably owing to lowering of micro-aqueous environmental pH around the enzyme leading to inhibition of enzyme activity. Mycelium bound A. niger lipase produced 80 g/l of isoamyl acetate within 96 h even though extremely less amount of enzyme activity was used for esterification. The presence of sodium sulphate during esterification reaction at higher substrate concentration resulted in increased conversion efficiency when we used mycelium bound enzyme preparations of A. niger NCIM 1207. This could be due to removal of excess water released during esterification reaction by sodium sulphate. High ester concentration (286.5 g/l) and conversion (73.5%) were obtained within 24 h using Novozyme 435 under these conditions.

Quantifying the Microbial Utilization of Methanogenesis and Methane Loss from Northern Wetlands

NASA Astrophysics Data System (ADS)

Corbett, J. E.; Tfaily, M.; Burdige, D.; Glaser, P. H.; Chanton, J.

2014-12-01

The importance of methanogenesis and percent of methane loss from the subsurface porewater in various northern wetland sites was quantified with isotope-mass balance equations. With equimolar amounts of CO2 and CH4 produced from methanogenesis, the amount of dissolved CO2 produced from methanogenesis as compared to other decomposition processes can be calculated and is equivalent to the amount of CH4 before loss due to ebullition, plant-mediated transport, and diffusion. This method was applied to porewater samples collected from various locations within permafrost collapse-scar bogs and northern peatlands. From the peatland sites, bogs produced less CO2-meth than fens (2.9 ± 1.3 mM and 3.7 ± 1.4 mM, respectively). Methanogenesis was a more utilized decomposition process in the bogs than the fens. However, greater amounts of CO2-meth found in fen sites was most likely due to the presence of more labile organic substrates resulting in greater overall production. More CH4 was lost in fens (89 ± 2.8%) than bogs (82 ± 5.3%) from plant-mediated transport as fens are dominated by vascular plants (Carex) while bogs are dominated by Sphagnum mosses. In permafrost sites, mid-bogs produced twice the amount of CO2-meth as bog moats (1.6 ± 0.63 mM and 0.82 ± 0.20 mM, respectively). Less methanogenesis was found in bog moats as recently thawed organic matter is exposed to initial decomposition processes and methane production grows over time. A similar amount of CH4 was lost from bog moats as mid bogs (63 ± 7.0% and 64 ± 9.3%, respectively) likely due to the greater density of vascular plants found within a bog moat.

The Utilization of Bark to Make Rigid Polyurethane Foams

NASA Astrophysics Data System (ADS)

D'Souza, Jason

This work focused on the characterization of polyols derived from the liquefaction or alkoxylation of bark. Regarding liquefaction, it was found that both temperature and solvent structure played a significant role in polyol properties. High temperature liquefaction resulted in the degradation of sugars, while liquefaction at mild temperatures preserved sugar structures as shown by 31P-NMR. It was also shown that liquefaction at 130°C was ideal in terms of producing a polyol with a relatively at, broad, plateau of molecular weight distribution, whereas liquefaction at 90 and 160°C produced polyols with a large amount of low molecular weight compounds. Regarding solvent structure, it was found that polyhydric alcohols with short chain primary hydroxyls resulted in less sugar degradation products and less formation of condensation side-products. It is proposed that the highly polar environment promoted grafting and prevented condensation onto other biopolymers. Using organic solvents it was found that ketonic solvents like acetyl acetone and cyclohexanone, through their highly polar carbonyl group could engage in hydrogen bonding through electron donation/proton accepting interactions. These enabled the solvent to reduce the amount of condensation reactions and improve liquefaction yield. The liquefied bark-based polyols were then used to make polyurethane foams. It was found that when a diversity of hydroxyl groups were present the foaming rate was reduced and this may react a slower rate of curing and explain why the bark foams had a greater amount of cells that underwent coalescence. It was also observed that the bark foams had a low amount of closed-cell content. Since closed-cell content plays a role in dictating elastic compression, this may explain why the bark foams exhibited a lower elastic modulus. Finally, as a contrast to liquefaction, bark was alkoxylated. It was observed that the conversion yield was higher than liquefaction. The polyols had a high average molecular weight with a broad distribution and far greater solubility. It is proposed that alkoxylation is far less degradative than liquefaction. This may explain why the foams showed improved compressive behaviour compared to the foams made from liqueed bark-based polyols. Through greater characterization of the structure of polyols produced via liquefaction and alkoxylation the relationships between reaction parameters, polyol structure, and foam properties can be better understood. This is an important step towards the utilization of bark to make polyurethane foams.

Adding liquid feed to a total mixed ration reduces feed sorting behavior and improves productivity of lactating dairy cows.

PubMed

DeVries, T J; Gill, R M

2012-05-01

This study was designed to determine the effect of adding a molasses-based liquid feed (LF) supplement to a total mixed ration (TMR) on the feed sorting behavior and production of dairy cows. Twelve lactating Holstein cows (88.2±19.5 DIM) were exposed, in a crossover design with 21-d periods, to each of 2 treatment diets: 1) control TMR and 2) control TMR with 4.1% dietary dry matter LF added. Dry matter intake (DMI), sorting, and milk yield were recorded for the last 7 d of each treatment period. Milk samples were collected for composition analysis for the last 3 d of each treatment period; these data were used to calculate 4% fat-corrected milk and energy-corrected milk yield. Sorting was determined by subjecting fresh feed and orts samples to particle separation and expressing the actual intake of each particle fraction as a percentage of the predicted intake of that fraction. Addition of LF did not noticeably change the nutrient composition of the ration, with the exception of an expected increase in dietary sugar concentration (from 4.0 to 5.4%). Liquid feed supplementation affected the particle size distribution of the ration, resulting in a lesser amount of short and a greater amount of fine particles. Cows sorted against the longest ration particles on both treatment diets; the extent of this sorting was greater on the control diet (55.0 vs. 68.8%). Dry matter intake was 1.4 kg/d higher when cows were fed the LF diet as compared with the control diet, resulting in higher acid-detergent fiber, neutral-detergent fiber, and sugar intakes. As a result of the increased DMI, cows tended to produce 1.9 kg/d more milk and produced 3.1 and 3.2 kg/d more 4% fat-corrected milk and energy-corrected milk, respectively, on the LF diet. As a result, cows tended to produce more milk fat (0.13 kg/d) and produced more milk protein (0.09 kg/d) on the LF diet. No difference between treatments was observed in the efficiency of milk production. Overall, adding a molasses-based LF to TMR can be used to decrease feed sorting, enhance DMI, and improve milk yield. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Methods for the synthesis of olefins and derivatives

DOEpatents

Burk, Mark J; Pharkya, Priti; Van Dien, Stephen J; Burgard, Anthony P; Schilling, Christophe H

2013-06-04

The invention provides a method of producing acrylic acid. The method includes contacting fumaric acid with a sufficient amount of ethylene in the presence of a cross-metathesis transformation catalyst to produce about two moles of acrylic acid per mole of fumaric acid. Also provided is an acrylate ester. The method includes contacting fumarate diester with a sufficient amount of ethylene in the presence of a cross-metathesis transformation catalyst to produce about two moles of acrylate ester per mole of fumarate diester. An integrated process for process for producing acrylic acid or acrylate ester is provided which couples bioproduction of fumaric acid with metathesis transformation. An acrylic acid and an acrylate ester production also is provided.

Methods for the synthesis of olefins and derivatives

DOEpatents

Burk, Mark J [San Diego, CA; Pharkya, Priti [San Diego, CA; Van Dien, Stephen J [Encinitas, CA; Burgard, Anthony P [Bellefonte, PA; Schilling, Christophe H [San Diego, CA

2011-09-27

The invention provides a method of producing acrylic acid. The method includes contacting fumaric acid with a sufficient amount of ethylene in the presence of a cross-metathesis transformation catalyst to produce about two moles of acrylic acid per mole of fumaric acid. Also provided is an acrylate ester. The method includes contacting fumarate diester with a sufficient amount of ethylene in the presence of a cross-metathesis transformation catalyst to produce about two moles of acrylate ester per mole of fumarate diester. An integrated process for process for producing acrylic acid or acrylate ester is provided which couples bioproduction of fumaric acid with metathesis transformation. An acrylic acid and an acrylate ester production also is provided.

Methods for synthesis of olefins and derivatives

DOEpatents

Burk, Mark J.; Pharkya, Priti; Van Dien, Stephen J.; Burgard, Anthony P.; Schilling, Christophe H.

2016-06-14

The invention provides a method of producing acrylic acid. The method includes contacting fumaric acid with a sufficient amount of ethylene in the presence of a cross-metathesis transformation catalyst to produce about two moles of acrylic acid per mole of fumaric acid. Also provided is an acrylate ester. The method includes contacting fumarate diester with a sufficient amount of ethylene in the presence of a cross-metathesis transformation catalyst to produce about two moles of acrylate ester per mole of fumarate diester. An integrated process for process for producing acrylic acid or acrylate ester is provided which couples bioproduction of fumaric acid with metathesis transformation. An acrylic acid and an acrylate ester production also is provided.

Water of Hydration Dynamics in Minerals Gypsum and Bassanite: Ultrafast 2D IR Spectroscopy of Rocks.

PubMed

Yan, Chang; Nishida, Jun; Yuan, Rongfeng; Fayer, Michael D

2016-08-03

Water of hydration plays an important role in minerals, determining their crystal structures and physical properties. Here ultrafast nonlinear infrared (IR) techniques, two-dimensional infrared (2D IR) and polarization selective pump-probe (PSPP) spectroscopies, were used to measure the dynamics and disorder of water of hydration in two minerals, gypsum (CaSO4·2H2O) and bassanite (CaSO4·0.5H2O). 2D IR spectra revealed that water arrangement in freshly precipitated gypsum contained a small amount of inhomogeneity. Following annealing at 348 K, water molecules became highly ordered; the 2D IR spectrum became homogeneously broadened (motional narrowed). PSPP measurements observed only inertial orientational relaxation. In contrast, water in bassanite's tubular channels is dynamically disordered. 2D IR spectra showed a significant amount of inhomogeneous broadening caused by a range of water configurations. At 298 K, water dynamics cause spectral diffusion that sampled a portion of the inhomogeneous line width on the time scale of ∼30 ps, while the rest of inhomogeneity is static on the time scale of the measurements. At higher temperature, the dynamics become faster. Spectral diffusion accelerates, and a portion of the lower temperature spectral diffusion became motionally narrowed. At sufficiently high temperature, all of the dynamics that produced spectral diffusion at lower temperatures became motionally narrowed, and only homogeneous broadening and static inhomogeneity were observed. Water angular motions in bassanite exhibit temperature-dependent diffusive orientational relaxation in a restricted cone of angles. The experiments were made possible by eliminating the vast amount of scattered light produced by the granulated powder samples using phase cycling methods.

Geologic emissions of methane to the atmosphere.

PubMed

Etiope, Giuseppe; Klusman, Ronald W

2002-12-01

The atmospheric methane budget is commonly defined assuming that major sources derive from the biosphere (wetlands, rice paddies, animals, termites) and that fossil, radiocarbon-free CH4 emission is due to and mediated by anthropogenic activity (natural gas production and distribution, and coal mining). However, the amount of radiocarbon-free CH4 in the atmosphere, estimated at approximately 20% of atmospheric CH4, is higher than the estimates from statistical data of CH4 emission from fossil fuel related anthropogenic sources. This work documents that significant amounts of "old" methane, produced within the Earth crust, can be released naturally into the atmosphere through gas permeable faults and fractured rocks. Major geologic emissions of methane are related to hydrocarbon production in sedimentary basins (biogenic and thermogenic methane) and, subordinately, to inorganic reactions (Fischer-Tropsch type) in geothermal systems. Geologic CH4 emissions include diffuse fluxes over wide areas, or microseepage, on the order of 10(0)-10(2) mg m(-2) day(-1), and localised flows and gas vents, on the order of 10(2) t y(-1), both on land and on the seafloor. Mud volcanoes producing flows of up to 10(3) t y(-1) represent the largest visible expression of geologic methane emission. Several studies have indicated that methanotrophic consumption in soil may be insufficient to consume all leaking geologic CH4 and positive fluxes into the atmosphere can take place in dry or seasonally cold environments. Unsaturated soils have generally been considered a major sink for atmospheric methane, and never a continuous, intermittent, or localised source to the atmosphere. Although geologic CH4 sources need to be quantified more accurately, a preliminary global estimate indicates that there are likely more than enough sources to provide the amount of methane required to account for the suspected missing source of fossil CH4.

The dynamic ejecta of compact object mergers and eccentric collisions.

PubMed

Rosswog, Stephan

2013-06-13

Compact object mergers eject neutron-rich matter in a number of ways: by the dynamical ejection mediated by gravitational torques, as neutrino-driven winds, and probably also a good fraction of the resulting accretion disc finally becomes unbound by a combination of viscous and nuclear processes. If compact binary mergers indeed produce gamma-ray bursts, there should also be an interaction region where an ultra-relativistic outflow interacts with the neutrino-driven wind and produces moderately relativistic ejecta. Each type of ejecta has different physical properties, and therefore plays a different role for nucleosynthesis and for the electromagnetic (EM) transients that go along with compact object encounters. Here, we focus on the dynamic ejecta and present results for over 30 hydrodynamical simulations of both gravitational wave-driven mergers and parabolic encounters as they may occur in globular clusters. We find that mergers eject approximately 1 per cent of a Solar mass of extremely neutron-rich material. The exact amount, as well as the ejection velocity, depends on the involved masses with asymmetric systems ejecting more material at higher velocities. This material undergoes a robust r-process and both ejecta amount and abundance pattern are consistent with neutron star mergers being a major source of the 'heavy' (A>130) r-process isotopes. Parabolic collisions, especially those between neutron stars and black holes, eject substantially larger amounts of mass, and therefore cannot occur frequently without overproducing gala- ctic r-process matter. We also discuss the EM transients that are powered by radioactive decays within the ejecta ('macronovae'), and the radio flares that emerge when the ejecta dissipate their large kinetic energies in the ambient medium.

Changing Feeding Regimes To Demonstrate Flexible Biogas Production: Effects on Process Performance, Microbial Community Structure, and Methanogenesis Pathways.

PubMed

Mulat, Daniel Girma; Jacobi, H Fabian; Feilberg, Anders; Adamsen, Anders Peter S; Richnow, Hans-Hermann; Nikolausz, Marcell

2016-01-15

Flexible biogas production that adapts biogas output to energy demand can be regulated by changing feeding regimes. In this study, the effect of changes in feeding intervals on process performance, microbial community structure, and the methanogenesis pathway was investigated. Three different feeding regimes (once daily, every second day, and every 2 h) at the same organic loading rate were studied in continuously stirred tank reactors treating distiller's dried grains with solubles. A larger amount of biogas was produced after feeding in the reactors fed less frequently (once per day and every second day), whereas the amount remained constant in the reactor fed more frequently (every 2 h), indicating the suitability of the former for the flexible production of biogas. Compared to the conventional more frequent feeding regimes, a methane yield that was up to 14% higher and an improved stability of the process against organic overloading were achieved by employing less frequent feeding regimes. The community structures of bacteria and methanogenic archaea were monitored by terminal restriction fragment length polymorphism (T-RFLP) analysis of 16S rRNA and mcrA genes, respectively. The results showed that the composition of the bacterial community varied under the different feeding regimes, and the observed T-RFLP patterns were best explained by the differences in the total ammonia nitrogen concentrations, H2 levels, and pH values. However, the methanogenic community remained stable under all feeding regimes, with the dominance of the Methanosarcina genus followed by that of the Methanobacterium genus. Stable isotope analysis showed that the average amount of methane produced during each feeding event by acetoclastic and hydrogenotrophic methanogenesis was not influenced by the three different feeding regimes. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Changing Feeding Regimes To Demonstrate Flexible Biogas Production: Effects on Process Performance, Microbial Community Structure, and Methanogenesis Pathways

PubMed Central

Mulat, Daniel Girma; Jacobi, H. Fabian; Feilberg, Anders; Adamsen, Anders Peter S.; Richnow, Hans-Hermann

2015-01-01

Flexible biogas production that adapts biogas output to energy demand can be regulated by changing feeding regimes. In this study, the effect of changes in feeding intervals on process performance, microbial community structure, and the methanogenesis pathway was investigated. Three different feeding regimes (once daily, every second day, and every 2 h) at the same organic loading rate were studied in continuously stirred tank reactors treating distiller's dried grains with solubles. A larger amount of biogas was produced after feeding in the reactors fed less frequently (once per day and every second day), whereas the amount remained constant in the reactor fed more frequently (every 2 h), indicating the suitability of the former for the flexible production of biogas. Compared to the conventional more frequent feeding regimes, a methane yield that was up to 14% higher and an improved stability of the process against organic overloading were achieved by employing less frequent feeding regimes. The community structures of bacteria and methanogenic archaea were monitored by terminal restriction fragment length polymorphism (T-RFLP) analysis of 16S rRNA and mcrA genes, respectively. The results showed that the composition of the bacterial community varied under the different feeding regimes, and the observed T-RFLP patterns were best explained by the differences in the total ammonia nitrogen concentrations, H2 levels, and pH values. However, the methanogenic community remained stable under all feeding regimes, with the dominance of the Methanosarcina genus followed by that of the Methanobacterium genus. Stable isotope analysis showed that the average amount of methane produced during each feeding event by acetoclastic and hydrogenotrophic methanogenesis was not influenced by the three different feeding regimes. PMID:26497462

Combining micro-structures and micro-algae to increase lipid production for bio-fuel

NASA Astrophysics Data System (ADS)

Vyawahare, Saurabh; Zhu, Emilly; Mestler, Troy; Estévez-Torres, André.; Austin, Robert

2011-03-01

3rd generation bio-fuels like lipid producing micro-algae are a promising source of energy that could replace our dependence on petroleum. However, until there are improvements in algae oil yields, and a reduction in the energy needed for processing, algae bio-fuels are not economically competitive with petroleum. Here, we describe our work combining micro-fabricated devices with micro-algae Neochloris oleoabundans, a species first isolated on the sand dunes of Saudi Arabia. Inserting micro-algae of varying fitness into a landscape of micro-habitats allows us to evolve and select them based on a variety of conditions like specific gravity, starvation response and Nile Red fluorescence (which is a marker for lipid production). Hence, we can both estimate the production of lipids and generate conditions that allow the creation and isolation of algae which produce higher amounts of lipids, while discarding the rest. Finally, we can use micro-fabricated structures and flocculation to de-water these high lipid producing algae, reducing the need for expensive centrifugation and filtration.

Extraction of extracellular lipids from chemoautotrophic bacteria Serratia sp. ISTD04 for production of biodiesel.

PubMed

Bharti, Randhir K; Srivastava, Shaili; Thakur, Indu Shekhar

2014-08-01

A CO2 sequestering bacterial strain, Serratia sp. ISTD04, that produces a significant amount of extracellular lipids was isolated from marble mine rocks. (14)C labeling analysis revealed that the rate of assimilation of CO2 by the strain is 0.756×10(-9)μmolCO2fixedcell(-1)h(-1). It was found to produce 466mg/l of extracellular lipid which was characterized using (1)H NMR. After transesterification of lipids, the total saturated and unsaturated FAME was found to be 51% and 49% respectively. The major FAME contained in the biodiesel were palmitic acid methyl ester (C16:0), oleic acid methyl ester (C18:1) and 10-nonadecenoic acid methyl ester (C19:1). Biodiesel produced by Serratia sp. ISTD04 is balanced in terms of FAME composition of good quality. It also contained higher proportion of oleic acid (35%) which makes it suitable for utilization in existing engines. Thus, the strain can be harnessed commercially to sequester CO2 into biodiesel. Copyright © 2014 Elsevier Ltd. All rights reserved.

Tool feed influence on the machinability of CO(2) laser optics.

PubMed

Arnold, J B; Steger, P J; Saito, T T

1975-08-01

Influence of tool feed on reflectivity of diamond-machined surfaces was evaluated using materials (gold, silver, and copper) from which CO(2) laser optics are primarily produced. Fifteen specimens were machined by holding all machining parameters constant, except tool feed. Tool feed was allowed to vary by controlled amounts from one evaluation zone (or part) to another. Past experience has verified that the quality of a diamond-machined surface is not a function of the cutting velocity; therefore, this experiment was conducted on the basis that a variation in cutting velocity was not an influencing factor on the diamondturning process. Inspection results of the specimens indicated that tool feeds significantly higher than 5.1 micro/rev (200 microin./rev) produced detrimental effects on the machined surfaces. In some cases, at feeds as high as 13 microm/rev (500 microin./rev), visible scoring was evident. Those surfaces produced with tool feeds less than 5.1 microm/rev had little difference in reflectivity. Measurements indicat d that their reflectivity existed in a range from 96.7% to 99.3% at 10.6 microm.

Elimination of methane in exhaust gas from biogas upgrading process by immobilized methane-oxidizing bacteria.

PubMed

Wu, Ya-Min; Yang, Jing; Fan, Xiao-Lei; Fu, Shan-Fei; Sun, Meng-Ting; Guo, Rong-Bo

2017-05-01

Biogas upgrading is essential for the comprehensive utilization of biogas as substitute of natural gas. However, the methane in the biogas can be fully recovered during the upgrading process of biogas, and the exhaust gas produced during biogas upgrading may contain a very low concentration of methane. If the exhaust gas with low concentration methane releases to atmosphere, it will be harmful to environment. In addition, the utilization of large amounts of digestate produced from biogas plant is another important issue for the development of biogas industry. In this study, solid digestate was used to produce active carbon, which was subsequently used as immobilized material for methane-oxidizing bacteria (MOB) in biofilter. Biofilter with MOB immobilized on active carbon was used to eliminate the methane in exhaust gas from biogas upgrading process. Results showed porous active carbon was successfully made from solid digestate. The final methane elimination capacity of immobilized MOB reached about 13molh -1 m -3 , which was more 4 times higher than that of MOB without immobilization. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Determination of vanadium concentration in foods produced on the Eastern Coast of Lake Maracaibo].

PubMed

Tudares, C M; Villalobos, H D

1998-04-01

In the northeastern coast of Lake Maracaibo it has been reported some years ago a high incidence of congenital malformations of the Central Nervous Systems (Neural Tube Defects Type). This epidemiological problem is present in other countries too (Ireland and New Zealand) and has been associated with oil activities. In fact, some experimental works inform about the vanadium compounds cellular toxic effects mainly in the Central Nervous System of mammals. The main goal of this work is to measure the vanadium content in foods produced in the northeastern coast of Lake Maracaibo. Lagunillas, Valmore Rodriguez, and Baralt were the districts selected for the work. The digestion of the samples achieved by the methodology reported by Myron et al., with Graphite Furnace Atomic Absorption. The amounts of vanadium in the different foods analized were higher than the controls in the bibliographic reports. At this moment, there is not definitive proofs that vanadium compounds are the etiological agents of the Neural Tube Defects, but, these compounds are presents in foods produced in the northeastern coast of Lake Maracaibo.

Neem gum as a binder in a formulated paracetamol tablet with reference to Acacia gum BP.

PubMed

Ogunjimi, Abayomi Tolulope; Alebiowu, Gbenga

2014-04-01

This study determined the physical, compressional, and binding properties of neem gum (NMG) obtained from the trunk of Azadirachta indica (A Juss) in a paracetamol tablet formulation in comparison with official Acacia gum BP (ACA). The physical and flow properties were evaluated using density parameters: porosity, Carr's index, Hausner's ratio, and flow rate. Compressional properties were analyzed using Heckel and Kawakita equations. The tensile strength, brittle fracture index, and crushing strength-friability/disintegration time ratio were used to evaluate the mechanical properties of paracetamol tablets while the drug release properties of the tablets were assessed using disintegration time and dissolution times. Tablet formulations containing NMG exhibited faster onset and higher amount of plastic deformation during compression than those containing ACA. Neem gum produced paracetamol tablets with lower mechanical strength; however, the tendency of the tablets to cap or laminate was lower when compared to those containing ACA. Inclusion of NMG improved the balance between binding and disintegration properties of paracetamol tablets produced than those containing ACA. Neem gum produced paracetamol tablets with lower disintegration and dissolution times than those containing ACA.

Toxins Produced by Valsa mali var. mali and Their Relationship with Pathogenicity

PubMed Central

Wang, Caixia; Li, Chao; Li, Baohua; Li, Guifang; Dong, Xiangli; Wang, Guoping; Zhang, Qingming

2014-01-01

Valsa mali var. mali (Vmm), the causal agent of apple tree canker disease, produces various toxic compounds, including protocatechuic acid, p-hydroxybenzoic acid, p-hydroxyacetophenone, 3-(p-hydroxyphenyl)propanoic acid and phloroglucinol. Here, we examined the relationship between toxin production and the pathogenicity of Vmm strains and determined their bioactivities in several assays, for further elucidating the pathogenesis mechanisms of Vmm and for developing new procedures to control this disease. The toxins were quantified with the high performance liquid chromatography (HPLC) method, and the results showed that the strain with attenuated virulence produced low levels of toxins with only three to four kinds of compounds being detectable. In contrast, higher amounts of toxins were produced by the more aggressive strain, and all five compounds were detected. This indicated a significant correlation between the pathogenicity of Vmm strains and their ability to produce toxins. However, this correlation only existed in planta, but not in vitro. During the infection of Vmm, protocatechuic acid was first detected at three days post inoculation (dpi), and the others at seven or 11 dpi. In addition, all compounds produced noticeable symptoms on host plants at concentrations of 2.5 to 40 mmol/L, with protocatechuic acid being the most effective compound, whereas 3-(p-hydroxyphenyl)propanoic acid or p-hydroxybenzoic acid were the most active compounds on non-host plants. PMID:24662481

Method for producing redox shuttles

DOEpatents

Pupek, Krzysztof Z.; Dzwiniel, Trevor L.; Krumdick, Gregory K.

2015-03-03

A single step method for producing a redox shuttle having the formula 2,5-di-tert-butyl-1,4-phenylene tetraethyl bis(phosphate) is provided, the method comprising phosphorylating tert butyl hydroquinone with a phosphate-containing reagent. Also provided is method for producing 2,5-di-tert-butyl-1,4-phenylene tetraethyl bis(phosphate), the method comprising solubilizing tert-butyl hydroquinone and tetrabutylammonium bromide with methyltetrahydrofuran to create a mixture; heating the mixture while adding base to the mixture in an amount to turn the mixture orange; and adding diethyl chlorophosphate to the orange mixture in an amount to phosphorylate the hydroquinone.

The removal of low level inorganics via electrogenerated hydrogen peroxide in the presence of catalytic amounts of Fe2+.

PubMed

Marrosu, G; Petrucci, R; Trazza, A

2001-01-01

Low level phosphites and hypophosphites were completely converted into phosphates, via hydrogen peroxide generated by cathodic reduction of oxygen in acidic aqueous medium at a reticulated vitreous carbon electrode, in the presence of little amounts of Fe2+. The contemporary regeneration of Fe2+ by cathodic reduction of Fe3+, produced by the well known Fenton reaction, furnishes an excellent way to continuously produce little amounts of the Fenton reactive and, as a consequence, of the powerful oxidant hydroxyl radical HO.. The best conditions for the complete removal of phosphorous as phosphites and hypophosphites are reported.

38 CFR 21.9640 - Rates of payment of educational assistance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... percent) and who— (1) Is enrolled at an institution of higher learning located in the United States, or at... amount for established charges paid directly to the institution of higher learning for the entire quarter... charged by the institution of higher learning; or (2) The maximum amount of tuition regularly charged per...

38 CFR 21.9640 - Rates of payment of educational assistance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... percent) and who— (1) Is enrolled at an institution of higher learning located in the United States, or at... amount for established charges paid directly to the institution of higher learning for the entire quarter... charged by the institution of higher learning; or (2) The maximum amount of tuition regularly charged per...

38 CFR 21.9640 - Rates of payment of educational assistance.

Code of Federal Regulations, 2012 CFR

2012-07-01

... percent) and who— (1) Is enrolled at an institution of higher learning located in the United States, or at... amount for established charges paid directly to the institution of higher learning for the entire quarter... charged by the institution of higher learning; or (2) The maximum amount of tuition regularly charged per...

38 CFR 21.9640 - Rates of payment of educational assistance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... percent) and who— (1) Is enrolled at an institution of higher learning located in the United States, or at... amount for established charges paid directly to the institution of higher learning for the entire quarter... charged by the institution of higher learning; or (2) The maximum amount of tuition regularly charged per...

Expression and characterization of a class III alcohol dehydrogenase gene from Gluconobacter frateurii in the presence of methanol during glyceric acid production from glycerol.

PubMed

Sato, Shun; Morita, Naoki; Kitamoto, Dai; Habe, Hiroshi

2013-01-01

Some acetic acid bacteria have been shown to produce large amounts of glyceric acid (GA) from glycerol, which is a by-product of biodiesel fuel (BDF) production. Previously, a Gluconobacter strain was found that produced decreased amounts of GA from glycerol in the presence of methanol, a major ingredient of raw glycerol derived from the BDF industry. Thus, a comparative transcriptome analysis of Gluconobacter frateurii NBRC103465 was performed to investigate changes in gene expression during GA production from glycerol in the presence of methanol. Cells grown with methanol showed upregulated expression of a class III alcohol dehydrogenase homolog (adhC(Gf)) and decreased GA production. adhC(Gf) was cloned and expressed heterologously in Escherichia coli, and the presence of an additional protein with an approximate molecular mass of 39 kDa in the cytosol of the recombinant E. coli cells was identified by SDS-PAGE. Activity measurements of the cytosol revealed that the translational product of adhC(Gf) exhibited formaldehyde dehydrogenase activity in the presence of nicotinamide adenine dinucleotide and glutathione. Gluconobacter frateurii cells grown in 1% methanol-containing glycerol were found to have fivefold higher formaldehyde dehydrogenase activity than cells grown without methanol, suggesting that adhC(Gf) in G. frateurii cells functions in the dissimilation of methanol-derived formaldehyde.

Antioxidants Potential of the Filamentous Fungi (Mucor circinelloides)

PubMed Central

Hussain, Syed Ammar; Yang, Junhuan; Ijaz, Muhammad Umair; Liu, Qing; Song, Yuanda

2017-01-01

Three important strains of Mucor circinelloides grown in complete and minimal media for specified period (72 h, 120 h and 168 h) under submerged fermentation conditions were investigated for their potential antioxidants/secondary metabolite production. All mycelial extracts demonstrated effective antioxidant activities in terms of β-carotene/linoleic acid bleaching, radical scavenging, reduction of metal ions and chelating abilities against ferrous ions. Different extraction methods and solvent systems affected the recovery yield and antioxidant activities of the extracts significantly (p ≤ 0.05). Ethanolic extracts were found to be rich source of antioxidant components and subsequently more effective in antioxidant properties. Fermentation period and media used also significantly affected (p ≤ 0.05) the antioxidant production and the resulting antioxidant properties. The (ethanolic) extracts of all the strains from late exponential growth phase (120 h) showed highest antioxidant production with topmost reducing, chelating and radical scavenging capabilities. Strain MC277.49 was found to be the highest producer of antioxidants followed by MC108.16 and WJ11. Phenolic compounds were detected significantly in higher (p ≤ 0.05) amount succeeded by the condensed tannins and flavonoids. Total phenol content of each extract was attributed to overall antioxidant capacity. Submerged fermentation with nutritional stress conditions were found to be excellent way of producing surplus amount of natural antioxidants/secondary metabolites with their vast potential commercial application in food and pharmaceutical industries. PMID:28991177

Antioxidants Potential of the Filamentous Fungi (Mucor circinelloides).

PubMed

Hameed, Ahsan; Hussain, Syed Ammar; Yang, Junhuan; Ijaz, Muhammad Umair; Liu, Qing; Suleria, Hafiz Ansar Rasul; Song, Yuanda

2017-10-07

Three important strains of Mucor circinelloides grown in complete and minimal media for specified period (72 h, 120 h and 168 h) under submerged fermentation conditions were investigated for their potential antioxidants/secondary metabolite production. All mycelial extracts demonstrated effective antioxidant activities in terms of β-carotene/linoleic acid bleaching, radical scavenging, reduction of metal ions and chelating abilities against ferrous ions. Different extraction methods and solvent systems affected the recovery yield and antioxidant activities of the extracts significantly ( p ≤ 0.05). Ethanolic extracts were found to be rich source of antioxidant components and subsequently more effective in antioxidant properties. Fermentation period and media used also significantly affected ( p ≤ 0.05) the antioxidant production and the resulting antioxidant properties. The (ethanolic) extracts of all the strains from late exponential growth phase (120 h) showed highest antioxidant production with topmost reducing, chelating and radical scavenging capabilities. Strain MC277.49 was found to be the highest producer of antioxidants followed by MC108.16 and WJ11. Phenolic compounds were detected significantly in higher ( p ≤ 0.05) amount succeeded by the condensed tannins and flavonoids. Total phenol content of each extract was attributed to overall antioxidant capacity. Submerged fermentation with nutritional stress conditions were found to be excellent way of producing surplus amount of natural antioxidants/secondary metabolites with their vast potential commercial application in food and pharmaceutical industries.

Enhanced diesel fuel fraction from waste high-density polyethylene and heavy gas oil pyrolysis using factorial design methodology.

PubMed

Joppert, Ney; da Silva, Alexsandro Araujo; da Costa Marques, Mônica Regina

2015-02-01

Factorial Design Methodology (FDM) was developed to enhance diesel fuel fraction (C9-C23) from waste high-density polyethylene (HDPE) and Heavy Gas Oil (HGO) through co-pyrolysis. FDM was used for optimization of the following reaction parameters: temperature, catalyst and HDPE amounts. The HGO amount was constant (2.00 g) in all experiments. The model optimum conditions were determined to be temperature of 550 °C, HDPE = 0.20 g and no FCC catalyst. Under such conditions, 94% of pyrolytic oil was recovered, of which diesel fuel fraction was 93% (87% diesel fuel fraction yield), no residue was produced and 6% of noncondensable gaseous/volatile fraction was obtained. Seeking to reduce the cost due to high process temperatures, the impact of using higher catalyst content (25%) with a lower temperature (500 °C) was investigated. Under these conditions, 88% of pyrolytic oil was recovered (diesel fuel fraction yield was also 87%) as well as 12% of the noncondensable gaseous/volatile fraction. No waste was produced in these conditions, being an environmentally friendly approach for recycling the waste plastic. This paper demonstrated the usefulness of using FDM to predict and to optimize diesel fuel fraction yield with a great reduction in the number of experiments. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effects of adding ethanol to KOH electrolyte on electrochemical performance of titanium carbide-derived carbon

NASA Astrophysics Data System (ADS)

Xu, Jiang; Zhang, Ruijun; Chen, Peng; Ge, Shanhai

2014-01-01

Porous carbide-derived carbons (CDCs) are synthesized from TiC at different chlorination temperatures as electrode materials for electrochemical capacitors. It is found that the microstructure of the produced CDCs has significant influence on both the hydrophilicity in aqueous KOH electrolyte and the resultant electrochemical performance. Because the TiC-CDC synthesized at higher temperature (e.g. 1000 °C) contains well-ordered graphite ribbons, it shows lower hydrophilicity and specific capacitance. It is also found that addition of a small amount of ethanol to KOH electrolyte effectively improves the wettability of the CDCs synthesized at higher temperature and the corresponding specific capacitance. Compared with the CDC synthesized at 600 °C, the CDC synthesized at 1000 °C shows fast ion transport and excellent capacitive behavior in KOH electrolyte with addition of ethanol because of the existences of mesopores and high specific surface area.

The synthesis of higher oxides of alkali and alkaline earth metals in an electric discharge: Theoretical and experimental studies

NASA Technical Reports Server (NTRS)

Bell, A. T.; Sadhukhan, P.

1974-01-01

Potassium hydroxide was subjected to the products of an electrical discharge sustained in oxygen and produced both potassium peroxide and superoxide. The conversion to higher oxides was shown to strongly depend upon the particle size of KOH, the position of KOH in the discharge zone, and the operating conditions of the discharge. Similar experiments were performed with hydroxides of lithium and calcium which do not form superoxides, but are converted to peroxides. The yields of peroxides were shown to strongly depend upon the operating conditions of the discharge. The absence of superoxides and the presence of peroxides of lithium and calcium was explained from the consideration of relative thermodynamic stability of the oxides of lithium and calcium. Thermogravimetric analysis was shown to provide a more accurate means for determining the amount of KO2 than previous methods.

Polymer quantization, stability and higher-order time derivative terms

NASA Astrophysics Data System (ADS)

Cumsille, Patricio; Reyes, Carlos M.; Ossandon, Sebastian; Reyes, Camilo

2016-03-01

The possibility that fundamental discreteness implicit in a quantum gravity theory may act as a natural regulator for ultraviolet singularities arising in quantum field theory has been intensively studied. Here, along the same expectations, we investigate whether a nonstandard representation called polymer representation can smooth away the large amount of negative energy that afflicts the Hamiltonians of higher-order time derivative theories, rendering the theory unstable when interactions come into play. We focus on the fourth-order Pais-Uhlenbeck model which can be reexpressed as the sum of two decoupled harmonic oscillators one producing positive energy and the other negative energy. As expected, the Schrödinger quantization of such model leads to the stability problem or to negative norm states called ghosts. Within the framework of polymer quantization we show the existence of new regions where the Hamiltonian can be defined well bounded from below.

Recovering the Atmospheric Resources of Mars: Updating the MARRS Study

NASA Astrophysics Data System (ADS)

England, Christopher; Hrubes, J. Dana

2006-01-01

In 2000 a conceptual design was conducted of a plant that extracts oxygen (O2) directly from the martian atmosphere, and that makes water and carbon monoxide (CO) as by-products. Updated estimates suggest that the amount of O2 in the atmosphere is about 2.3 times greater than that used as the basis for the 2000 study. In this paper, estimates for O2 and by-products, and for energy and mass requirements based on the higher O2 value are updated. The basis for the design, termed ``MARRS'' for Mars Atmosphere Resource Recovery System, is the NASA/JSC Mars Reference Mission (MRM) requirement for O2, estimated at 5.8 kg/hr for about 500 sols. The 2000 study based its design on an atmospheric O2 content of 0.13%, the then-accepted value. Analysis now places the O2 content at about 0.3%, reducing the amount of energy and equipment proportionately. The revised estimate of the thermal power to meet MRM requirements for O2 is an average of about 52 kW, seasonally variable. The new mass estimate is 7898 kg, down from 13650 kg. The new estimate of oxygen content correspondingly reduces the amounts of by-products that can be recovered. CO, a primary fuel and propellant precursor, is produced at about 0.2 kg/kg O2. Water, possibly available at about 0.04 kg/kg O2, is believed not recoverable by the MARRS process at this lower level, even seasonally. An equation is provided for the seasonal variation in atmospheric O2 fraction based on Viking pressure measurements. Oxygen varies seasonally from about 0.25% or 0.34%, the variability affecting plant design. While the higher O2 fraction means reduced amounts of by-products from the MARRS process, large amounts of nitrogen (liquid and gas), argon gas and liquid carbon dioxide (CO2) remain available as by-products for use as respiratory agents, refrigerants, propellants, propellant precursors and working fluids for emergency or backup power, transportation, and surface operations such as drilling.

Enteral and parenteral lipid requirements of preterm infants.

PubMed

Lapillonne, Alexandre

2014-01-01

Lipids provide infants with most of their energy needs. The major portion of the fat in human milk is found in the form of triglycerides, the phospholipids and cholesterol contributing for only a small proportion of the total fat. Long-chain polyunsaturated fatty acids (LC-PUFAs) are crucial for normal development of the central nervous system and have potential for long-lasting effects that extend beyond the period of dietary insufficiency. Given the limited and highly variable formation of docosahexaenoic acid (DHA) from α-linolenic acid, and because DHA is critical for normal retinal and brain development in the human, DHA should be considered to be conditionally essential during early development. In early enteral studies, the amount of LC-PUFAs administered in formula was chosen to produce the same concentration of arachidonic acid and DHA as in term breast milk. Recent studies report outcome data in preterm infants fed formula with DHA content 2-3 times higher than the current concentration. Overall, these studies show that providing larger amounts of DHA supplements is associated with better neurological outcomes and may provide other health benefits. One study further suggests that the smallest babies are the most vulnerable to DHA deficiency and likely to reap the greatest benefit from high-dose DHA supplementation. Current nutritional management may not provide sufficient amounts of preformed DHA during the parenteral and enteral nutrition periods and in very preterm/very low birth weight infants until due date and higher amounts than those routinely used are likely to be necessary to compensate for intestinal malabsorption, DHA oxidation, and early deficit. Recommendations for the healthcare provider are made in order to prevent lipid and more specifically LC-PUFA deficit. Research should be continued to fill the gaps in knowledge and to further refine the adequate intake for each group of preterm infants. © 2014 S. Karger AG, Basel.

Validation of methodology for determination of the mercury methylation potential in sediments using radiotracers.

PubMed

Zizek, Suzana; Ribeiro Guevara, Sergio; Horvat, Milena

2008-04-01

Experiments to determine the mercury methylation potential were performed on sediments from two locations on the river Idrijca (Slovenia), differing in ambient mercury concentrations. The tracer used was the radioactive isotope (197)Hg. The benefit of using this tracer is its high specific activity, which enables spikes as low as 0.02 ng Hg(2+) g(-1) of sample to be used. It was therefore possible to compare the efficiency of the methylation potential experiments over a range of spike concentrations from picogram to microgram levels. The first part of the work aimed to validate the experimental blanks and the second part consisted of several series of incubation experiments on two different river sediments using a range of tracer additions. The results showed high variability in the obtained methylation potentials. Increasing Hg(2+) additions gave a decrease in the percentage of the tracer methylated during incubation; in absolute terms, the spikes that spanned four orders of magnitude (0.019-190 pg g(-1) of sediment slurry) resulted in MeHg formation between 0.01 and 0.1 ng MeHg g(-1) in Podroteja and Kozarska Grapa. Higher spikes resulted in slightly elevated MeHg production (up to a maximum of 0.27 ng g(-1)). The values of methylation potential were similar in both sediments. The results imply that the experimental determination of mercury methylation potential strongly depends on the experimental setup itself and the amount of tracer added to the system under study. It is therefore recommended to use different concentrations of tracer and perform the experiments in several replicates. The amount of mercury available for methylation in nature is usually very small. Therefore, adding very low amounts of tracer in the methylation potential studies probably gives results that have a higher environmental relevance. It is also suggested to express the results obtained in absolute amounts of MeHg produced and not just as the percentage of the added tracer.

Toxicity evaluation of cordycepin and its delivery system for sustained in vitro anti-lung cancer activity

NASA Astrophysics Data System (ADS)

Aramwit, Pornanong; Porasuphatana, Supatra; Srichana, Teerapol; Nakpheng, Titpawan

2015-03-01

In the previous study, we have found that the cordycepin which was extracted from Cordyceps mycelia produced by growing Cordyceps militaris on the dead larva of Bombyx mori silkworms showed the anti-proliferative effect toward lung cancer cells without toxicity to non-cancer cells. In this work, the cordycepin was tested for its in vitro mutagenicity and in vivo toxicity. From the Ames test and subacute toxicity test using oral administration in a rat model, the cordycepin was proved to be a non-mutagenic and non-toxic compound. The hematology and blood chemistry as well as the microanatomical characteristic of the tissues of rats fed with cordycepin every day for consecutive 30 days were comparable to those of the normal ones. Then, the cordycepin was incorporated in gelatin type A (GA) and gelatin type B (GB) nanoparticles aimed to sustain its release and activity. The cordycepin incorporated in both GA and GB nanoparticles showed the sustained release profiles. GA nanoparticles could encapsulate cordycepin at higher encapsulation efficiency due to the attractive electrostatic interaction between the positive-charged GA and the negative-charged cordycepin. However, GA nanoparticles released cordycepin at the higher amount possibly because of the large surface area of small size nanoparticles. Comparing to GB nanoparticles, the higher amount of cordycepin released from GA nanoparticles showed the higher anti-proliferative and anti-migratory effects on A549 lung cancer cells. In conclusion, GA nanoparticles were suggested as a suitable carrier for the sustained release of cordycepin. The GA nanoparticles releasing cordycepin could be an effective and non-invasive material for the treatment of lung cancer cells.

Porous filtering media comparison through wet and dry sampling of fixed bed gasification products

NASA Astrophysics Data System (ADS)

Allesina, G.; Pedrazzi, S.; Montermini, L.; Giorgini, L.; Bortolani, G.; Tartarini, P.

2014-11-01

The syngas produced by fixed bed gasifiers contains high quantities of particulate and tars. This issue, together with its high temperature, avoids its direct exploitation without a proper cleaning and cooling process. In fact, when the syngas produced by gasification is used in an Internal Combustion engine (IC), the higher the content of tars and particulate, the higher the risk to damage the engine is. If these compounds are not properly removed, the engine may fail to run. A way to avoid engine fails is to intensify the maintenance schedule, but these stops will reduce the system profitability. From a clean syngas does not only follow higher performance of the generator, but also less pollutants in the atmosphere. When is not possible to work on the gasification reactions, the filter plays the most important role in the engine safeguard process. This work is aimed at developing and comparing different porous filters for biomass gasifiers power plants. A drum filter was developed and tested filling it with different filtering media available on the market. As a starting point, the filter was implemented in a Power Pallet 10 kW gasifier produced by the California-based company "ALL Power Labs". The original filter was replaced with different porous biomasses, such as woodchips and corn cobs. Finally, a synthetic zeolites medium was tested and compared with the biological media previously used. The Tar Sampling Protocol (TSP) and a modified "dry" method using the Silica Gel material were applied to evaluate the tars, particulate and water amount in the syngas after the filtration process. Advantages and disadvantages of every filtering media chosen were reported and discussed.

Antimicrobial peptides and nitric oxide production by neutrophils from periodontitis subjects

PubMed Central

Mariano, F.S.; Campanelli, A.P.; Nociti, F.H.; Mattos-Graner, R.O.; Gonçalves, R.B.

2012-01-01

Neutrophils play an important role in periodontitis by producing nitric oxide (NO) and antimicrobial peptides, molecules with microbicidal activity via oxygen-dependent and -independent mechanisms, respectively. It is unknown whether variation in the production of antimicrobial peptides such as LL-37, human neutrophil peptides (HNP) 1-3, and NO by neutrophils influences the pathogenesis of periodontal diseases. We compared the production of these peptides and NO by lipopolysaccharide (LPS)-stimulated neutrophils isolated from healthy subjects and from patients with periodontitis. Peripheral blood neutrophils were cultured with or without Aggregatibacter actinomycetemcomitans-LPS (Aa-LPS), Porphyromonas gingivalis-LPS (Pg-LPS) and Escherichia coli-LPS (Ec-LPS). qRT-PCR was used to determine quantities of HNP 1-3 and LL-37 mRNA in neutrophils. Amounts of HNP 1-3 and LL-37 proteins in the cell culture supernatants were also determined by ELISA. In addition, NO levels in neutrophil culture supernatants were quantitated by the Griess reaction. Neutrophils from periodontitis patients cultured with Aa-LPS, Pg-LPS and Ec-LPS expressed higher HNP 1-3 mRNA than neutrophils from healthy subjects. LL-37 mRNA expression was higher in neutrophils from patients stimulated with Aa-LPS. Neutrophils from periodontitis patients produced significantly higher LL-37 protein levels than neutrophils from healthy subjects when stimulated with Pg-LPS and Ec-LPS, but no difference was observed in HNP 1-3 production. Neutrophils from periodontitis patients cultured or not with Pg-LPS and Ec-LPS produced significantly lower NO levels than neutrophils from healthy subjects. The significant differences in the production of LL-37 and NO between neutrophils from healthy and periodontitis subjects indicate that production of these molecules might influence individual susceptibility to important periodontal pathogens. PMID:22850872

Maternal effects on male weaponry: female dung beetles produce major sons with longer horns when they perceive higher population density

PubMed Central

2012-01-01

Background Maternal effects are environmental influences on the phenotype of one individual that are due to the expression of genes in its mother, and are expected to evolve whenever females are better capable of assessing the environmental conditions that their offspring will experience than the offspring themselves. In the dung beetle Onthophagus taurus, conditional male dimorphism is associated with alternative reproductive tactics: majors fight and guard females whereas minors sneak copulations. Furthermore, variation in dung beetle population density has different fitness consequences for each male morph, and theory predicts that higher population density might select for a higher frequency of minors and/or greater expenditure on weaponry in majors. Because adult dung beetles provide offspring with all the nutritional resources for their development, maternal effects strongly influence male phenotype. Results Here we tested whether female O. taurus are capable of perceiving population density, and responding by changing the phenotype of their offspring. We found that mothers who were reared with other conspecifics in their pre-mating period produced major offspring that had longer horns across a wider range of body sizes than the major offspring of females that were reared in isolation in their pre-mating period. Moreover, our results indicate that this maternal effect on male weaponry does not operate through the amount of dung provided by females to their offspring, but is rather transmitted through egg or brood mass composition. Finally, although theory predicts that females experiencing higher density might produce more minor males, we found no support for this, rather the best fitting models were equivocal as to whether fewer or the same proportions of minors were produced. Conclusions Our study describes a new type of maternal effect in dung beetles, which probably allows females to respond to population density adaptively, preparing at least their major offspring for the sexual competition they will face in the future. This new type of maternal effect in dung beetles represents a novel transgenerational response of alternative reproductive tactics to population density. PMID:22823456

Maternal effects on male weaponry: female dung beetles produce major sons with longer horns when they perceive higher population density.

PubMed

Buzatto, Bruno A; Tomkins, Joseph L; Simmons, Leigh W

2012-07-23

Maternal effects are environmental influences on the phenotype of one individual that are due to the expression of genes in its mother, and are expected to evolve whenever females are better capable of assessing the environmental conditions that their offspring will experience than the offspring themselves. In the dung beetle Onthophagus taurus, conditional male dimorphism is associated with alternative reproductive tactics: majors fight and guard females whereas minors sneak copulations. Furthermore, variation in dung beetle population density has different fitness consequences for each male morph, and theory predicts that higher population density might select for a higher frequency of minors and/or greater expenditure on weaponry in majors. Because adult dung beetles provide offspring with all the nutritional resources for their development, maternal effects strongly influence male phenotype. Here we tested whether female O. taurus are capable of perceiving population density, and responding by changing the phenotype of their offspring. We found that mothers who were reared with other conspecifics in their pre-mating period produced major offspring that had longer horns across a wider range of body sizes than the major offspring of females that were reared in isolation in their pre-mating period. Moreover, our results indicate that this maternal effect on male weaponry does not operate through the amount of dung provided by females to their offspring, but is rather transmitted through egg or brood mass composition. Finally, although theory predicts that females experiencing higher density might produce more minor males, we found no support for this, rather the best fitting models were equivocal as to whether fewer or the same proportions of minors were produced. Our study describes a new type of maternal effect in dung beetles, which probably allows females to respond to population density adaptively, preparing at least their major offspring for the sexual competition they will face in the future. This new type of maternal effect in dung beetles represents a novel transgenerational response of alternative reproductive tactics to population density.

Effectiveness of the Solar Panels in the Castro Valley Unified School District Based on Projected Amount of Energy to be Produced

NASA Astrophysics Data System (ADS)

Sparks, J. R.; Palmer, T. C.; Siegel, A. P.

2014-12-01

In recent years Americans have warmed to the idea of installing solar panels to their homes and businesses. These panels help reduce the cost of receiving energy from power plants that lose a lot of energy in transportation. These power plants provide energy by burning gas or coal producing emissions that add to the growing problem of pollution and global warming. In 2010 the Castro Valley Unified School District decided to add solar panels to Canyon Middle School, Castro Valley High School, and Castro Valley Adult School. We researched whether the solar panels reached their projected amount of energy (74%) for the sites where the panels were placed. The solar panels at all three sites were found to exceed these projected amounts. The solar panels at each site produce a little over 74% for the each school.

Beliefs and social behavior in a multi-period ultimatum game

PubMed Central

Azar, Ofer H.; Lahav, Yaron; Voslinsky, Alisa

2015-01-01

We conduct a multi-period ultimatum game in which we elicit players' beliefs. Responders do not predict accurately the amount that will be offered to them, and do not get better in their predictions over time. At the individual level we see some effect of the mistake in expectations in the previous period on the responder's expectation about the offer in the current period, but this effect is relatively small. The proposers' beliefs about the minimum amount that responders will accept is significantly higher than the minimum amount responders believe will be accepted by other responders. The proposer's belief about the minimal acceptable offer does not change following a rejection. Nevertheless, the proposer's offer in the next period does increase following a rejection. The probability of rejection increases when the responder has higher expectations about the amount that will be offered to him or higher beliefs about the minimal amount that other responders will accept. PMID:25762909

Principal thorium resources in the United States

USGS Publications Warehouse

Staatz, Mortimer Hay; Armbrustmacher, T.J.; Olson, J.C.; Brownfield, I.K.; Brock, M.R.; Lemons, J.F.; Coppa, L.V.; Clingan, B.V.

1979-01-01

Resources were assessed for thorium in the higher grade and better known deposits in the United States in: (1) veins, (2) massive carbonatites, (3) stream placers of North and South Carolina, and (4) disseminated deposits. Thorium resources for the first three categories were divided into reserves and probable potential resources. Each of these then were separated into the following cost categories: (1) the amount of ThO2 producible at less than $15 per pound, (2) the amount producible at between $15 and $30 per pound, and (3) the amount producible at more than $50 per pound. The type of mining and milling needed at each deposit determines the capital, operating, and fixed costs of both mining and milling. Costs start with the clearing of land and are carried through to the final product, which for all deposits is ThO2. Capital costs of mining are affected most by the type of mining and the size of the mine. Those of milling are affected most by the kind of mill, its size, and whether or not extra circuits are needed for the separation of rare earths or some other byproduct. Veins, massive carbonatites, and stream placers of North and South Carolina have reserves of 188,000 short tons of ThO2 and probable potential resources of 505,000 tons of ThO2. Approximately half of the reserves and probable potential resources can be produced at less than $30 per pound of ThO2. Veins are the highest grade source in the United States and have total reserves of 142,000 tons of ThO2 and probable potential resources of 343,000 tons. About 90 percent of the reserves and 91 percent of the probable potential resources can be produced at less than $15 per pound of ThO2. Seven vein districts were evaluated: (1) Lemhi Pass, Mont.-Idaho, (2) Wet Mountains, Colo., (3) Powderhorn, Colo., (4) Hall Mountain, Idaho, (5) Diamond Creek, Idaho, (6) Bear Lodge Mountains, Wyo. and (7) Mountain Pass, Calif. Eighty-seven percent of the total reserves and probable potential resources are in the Lemhi Pass and Wet Mountains Districts. The first district has reserves of 68,000 tons of ThO2 and probable potential resources of 124,000 tons that can be produced at less than $15 per pound; the second district has 54,000 tons of reserves and 141,000 tons of probable potential resources producible at less than $15 per pound. Rare earths are a common byproduct, and in many veins they are from one-half to several times as abundant as thorium. Massive carbonatite bodies are large-tonnage low-grade deposits. Thorium in these deposits would be a byproduct either of rare earth or of niobium mining. The Iron Hill carbonatite body in the Powderhorn district, Colorado, and the Sulfide Queen carbonatite body in the Mountain Pass district, California, were evaluated. These two deposits contain 40,800 tons of ThO2 in reserves and 125,000 tons of ThO2 in probable potential resources. More than 80 percent of this total is in the Iron Hill carbonatite. This thorium is entirely a byproduct and is producible at less than $15 per pound of ThO2. The Sulphide Queen massive carbonatite deposit was being mined in 1977 for rare earths, and thorium could be recovered by adding an extra circuit to the existing mill. Stream placers in North and South Carolina occur both in the Piedmont and just east of the Fall Line. The reserves of these deposits total 5,270 tons of ThO2, and the probable potential resources are 36,800 tons of ThO2. The Piedmont placers are all too small to produce ThO2 at a cost of less than $50 per pound. One placer on Hollow Creek, S.C., just east of the Fall Line had reserves of 2,040 tons of ThO2 that is producible at between $15 and $30 per pound. Thorium occurs in monazite in these placers. Other heavy minerals that would be recovered with the monazite include rutile, zircon, and ilmenite. In addition to thorium, monazite contains large amounts of rare earths and small amounts of uranium; both can be recovered during the process that separates thorium fr

76 FR 53818 - Determining the Amount of Taxes Paid for Purposes of the Foreign Tax Credit; Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-30

... Determining the Amount of Taxes Paid for Purposes of the Foreign Tax Credit; Correction AGENCY: Internal... determination of the amount of taxes paid for purposes of the foreign tax credit. These regulations address certain highly structured transactions that produce inappropriate foreign tax credit results. The...

Importance of deep mixing and silicic acid in regulating phytoplankton biomass and community in the iron-limited Antarctic Polar Front region in summer

NASA Astrophysics Data System (ADS)

Cheah, Wee; Soppa, Mariana A.; Wiegmann, Sonja; Ossebaar, Sharyn; Laglera, Luis M.; Strass, Volker H.; Santos-Echeandía, Juan; Hoppema, Mario; Wolf-Gladrow, Dieter; Bracher, Astrid

2017-04-01

Phytoplankton community structure and their physiological response in the vicinity of the Antarctic Polar Front (APF; 44°S to 53°S, centred at 10°E) were investigated as part of the ANT-XXVIII/3 Eddy-Pump cruise conducted in austral summer 2012. Our results show that under iron-limited (< 0.3 μmolm-3) conditions, high total chlorophyll-a (TChl-a) concentrations (> 0.6 mgm-3) can be observed at stations with deep mixed layer (> 60 m) across the APF. In contrast, light was excessive at stations with shallower mixed layer and phytoplankton were producing higher amounts of photoprotective pigments, diadinoxanthin (DD) and diatoxanthin (DT), at the expense of TChl-a, resulting in higher ratios of (DD+DT)/TChl-a. North of the APF, significantly lower silicic acid (Si(OH)4) concentrations (< 2 mmolm-3) lead to the domination of nanophytoplankton consisting mostly of haptophytes, which produced higher ratios of (DD+DT)/TChl-a under relatively low irradiance conditions. The Si(OH)4 replete (> 5 mmolm-3) region south of the APF, on the contrary, was dominated by microphytoplankton (diatoms and dinoflagellates) with lower ratios of (DD+DT)/TChl-a, despite having been exposed to higher levels of irradiance. The significant correlation between nanophytoplankton and (DD+DT)/TChl-a indicates that differences in taxon-specific response to light are also influencing TChl-a concentration in the APF during summer. Our results reveal that provided mixing is deep and Si(OH)4 is replete, TChl-a concentrations higher than 0.6 mgm-3 are achievable in the iron-limited APF waters during summer.

Electricity generation in microbial fuel cells using neutral red as an electronophore

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, D.H.; Zeikus, J.G.

2000-04-01

Neutral red (NR) was utilized as an electron mediator in microbial fuel cells consuming glucose to study both its efficiency during electricity generation and its role in altering anaerobic growth and metabolism of Escherichia coli and Actinobacillus succinogenes. A study of chemical fuel cells in which NADH, NR, and ferricyanide were the electron donor, the electronophore, and the electron acceptor, respectively, showed that electrical current produced from NADH was proportional to the concentration of NADH. Fourfold more current was produced from NADH in chemical fuel cells when NR was the electron mediator than when thionin was the electron mediator. Inmore » microbial fuel cells in which E. coli resting cells were used the amount of current produced from glucose when NR was the electron mediator was 10-fold more than the amount produced when thionin was the electron mediator. The amount of electrical energy generated and the amount of current produced from glucose in NR-mediated microbial fuel cells containing either E. coli or A. succinogenes were about 10- and 2-fold greater, respectively, when resting cells were used than when growing cells were used. Cell growth was inhibited substantially when these microbial fuel cells were making current, and more oxidized end products were formed under these conditions. When sewage sludge was used in the fuel cell, stable and equivalent levels of current were obtained with glucose, as observed in the pure-culture experiments. These results suggest that NR is better than other electron mediators used in microbial fuel cells and that sludge production can be decreased while electricity is produced in fuel cells. Their results are discussed in relation to factors that may improve the relatively low electrical efficiencies obtained with microbial fuel cells.« less

Why a New Goal for Corporate Giving to Higher Education?

ERIC Educational Resources Information Center

Fey, John T.

A new goal for corporate giving to higher education has emerged. It is to increase the amount of giving to the institution each year by at least the amount of inflation. Both inflation and dangerous demographics will threaten higher education excessively in the coming decade. The demographic picture will vary greatly by geographic region, and the…

Extraction mechanism of ultrasound assisted extraction and its effect on higher yielding and purity of artemisinin crystals from Artemisia annua L. leaves.

PubMed

Chemat, Smain; Aissa, Abdallah; Boumechhour, Abdenour; Arous, Omar; Ait-Amar, Hamid

2017-01-01

This study proposes an ultrasound-horn system for the extraction of a natural active compound "artemisinin" from Artemisia annua L. leaves as an alternative to hot maceration technique. Ultrasound leaching improves artemisinin recovery at all temperatures where only ten minutes is required to recover 70% (4.42mgg -1 ) compared to 60min of conventional hot leaching for the same yield. For instance, ultrasound treatment at 30°C produced a higher yield than the one obtained by conventional maceration at 40°C. Kinetic study suggests that the extraction pattern can be assimilated, during the first ten minutes, to a first order steady state, from which activation energy calculations revealed that each gram of artemisinin required 7.38kJ in ultrasound versus 10.3kJ in the conventional system. Modeling results indicate the presence of two extraction stages, a faster stage with a diffusion coefficient of 19×10 -5 cm 2 min -1 for ultrasound technique at 40°C, seven times higher than the conventional one; and a second deceleration stage similar for both techniques with diffusion coefficient ranging from 1.7 to 3.1×10 -5 cm 2 min -1 . It is noted that the efficient ultrasound extraction potential implies extraction of higher amount of co-metabolites so low artemisinin crystal purity is engendered but a combination with a purification step using activated charcoal and celite adsorbents produced crystals with comparable purity for conventional and ultrasound samples. Copyright © 2016 Elsevier B.V. All rights reserved.

Fatty acid composition modulates sensitivity of Legionella pneumophila to warnericin RK, an antimicrobial peptide.

PubMed

Verdon, Julien; Labanowski, Jérome; Sahr, Tobias; Ferreira, Thierry; Lacombe, Christian; Buchrieser, Carmen; Berjeaud, Jean-Marc; Héchard, Yann

2011-04-01

Warnericin RK is an antimicrobial peptide, produced by a Staphyloccocus warneri strain, described to be specifically active against Legionella, the pathogenic bacteria responsible for Legionnaires' disease. Warnericin RK is an amphiphilic alpha-helical peptide, which possesses a detergent-like mode of action. Two others peptides, δ-hemolysin I and II, produced by the same S. warneri strain, are highly similar to S. aureus δ-hemolysin and also display anti-Legionella activity. It has been recently reported that S. aureus δ-hemolysin activity on vesicles is likewise related to phospholipid acyl-chain structure, such as chain length and saturation. As staphylococcal δ-hemolysins were highly similar, we thus hypothesized that fatty acid composition of Legionella's membrane might influence the sensitivity of the bacteria to warnericin RK. Relationship between sensitivity to the peptide and fatty acid composition was then followed in various conditions. Cells in stationary phase, which were already described as less resistant than cells in exponential phase, displayed higher amounts of branched-chain fatty acids (BCFA) and short chain fatty acids. An adapted strain, able to grow at a concentration 33 fold higher than minimal inhibitory concentration of the wild type (i.e. 1μM), was isolated after repeated transfers of L. pneumophila in the presence of increased concentrations of warnericin RK. The amount of BCFA was significantly higher in the adapted strain than in the wild type strain. Also, a transcriptomic analysis of the wild type and adapted strains showed that two genes involved in fatty acid biosynthesis were repressed in the adapted strain. These genes encode enzymes involved in desaturation and elongation of fatty acids respectively. Their repression was in agreement with the decrease of unsaturated fatty acids and fatty acid chain length in the adapted strain. Conclusively, our results indicate that the increase of BCFA and the decrease of fatty acid chain length in membrane were correlated with the increase in resistance to warnericin RK. Therefore, fatty acid profile seems to play a critical role in the sensitivity of L. pneumophila to warnericin RK. Copyright © 2010 Elsevier B.V. All rights reserved.

On the Role of High Amounts of Mn Element in CdS Structure

NASA Astrophysics Data System (ADS)

Gonullu, Meryem Polat; Kose, Salih

2017-03-01

CdS and MnS are technologically important semiconducting materials. In this work, due to the limited ability of these materials separately, a detailed characterization of the new samples formed by the combined use of them has been reported. CdS films, with the incorporation of Mn in a wide range of concentrations, have been produced by a low-cost Ultrasonic Spray Pyrolysis set-up. Spectroscopic Ellipsometry (SE) has been used to determine the thicknesses and optical constants ( n, k) of the samples. It has been determined that samples with high amounts of Mn have lower refractive index values. Absorbance spectra have shown additional band edges along with the one belonging to CdS, for samples with Mn concentrations higher than 50 pct. This has been attributed to a phase separation above this limit. Raman spectroscopy analysis which shows additional Raman peaks belonging to MnS phase also supports these findings. Depending on this phase separation, crystalline structure has been deteriorated. Surface properties of the samples have been investigated by SEM and AFM. Elemental analysis has been performed by EDS. Resistivity measurements performed by a four-probe set-up have shown that samples containing high amount of Mn have lower electrical resistivity values.

[Coal fineness effect on primary particulate matter features during pulverized coal combustion].

PubMed

Lü, Jian-yi; Li, Ding-kai

2007-09-01

Three kinds of coal differed from fineness were burned in a laboratory-scale drop tube furnace for combustion test, and an 8-stage Andersen particle impactor was employed for sampling the primary particulate matter (PM), in order to study coal fineness effect on primary PM features during pulverized coal combustion. It has been shown that the finer the coal was, the finer the PM produced. PM, emission amount augmented with coal fineness decreased, and the amount of PM10 increased from 13 mg/g to 21 mg/g respectively generated by coarse coal and fine coal. The amount of PM2.5 increased from 2 mg/g to 8 mg/g at the same condition. Constituents and content in bulk ash varied little after three different fineness coal combustion, while the appearance of grading PM differed visibly. The value of R(EE) increased while the coal fineness deceased. The volatility of trace elements which were investigated was Pb > Cr > Zn > Cu > Ni in turn. The concentration of poisonous trace elements was higher which generated from fine coal combustion. The volatilization capacity was influenced little by coal fineness, but the volatilization extent was influenced differently by coal fineness. Fine coal combustion affects worse environment than coarse coal does.

Hydrolysis of Mg(BH4)2 and its coordination compounds as a way to obtain hydrogen

NASA Astrophysics Data System (ADS)

Solovev, Mikhail V.; Chashchikhin, Oleg V.; Dorovatovskii, Pavel V.; Khrustalev, Victor N.; Zyubin, A. S.; Zyubina, T. S.; Kravchenko, O. V.; Zaytsev, Alexey A.; Dobrovolsky, Yu. A.

2018-02-01

Three ligand-stabilized Mg(BH4)2-based complexes have been synthesized and evaluated as potential hydrogen storage media for portable fuel cell applications. The new borohydrides: Mg(BH4)2 × 0.5Et2O and Mg(BH4)2 × diglyme (diglyme - CH3O(CH2)2O(CH2)2OCH3) have been synthesized and examined by X-ray single crystal diffraction method. Hydrolysis reactions of the compounds liberate hydrogen in quantities ranging from 46 to 96% of the theoretical yield. The hydrolysis of Mg(BH4)2 and other borohydrides is also accompanied by the diborane formation. The amount of liberated diborane depends on the Mg-coordination environment. To explain this fact quantum-chemical calculations have been performed. It is shown that formation of Mg-O-Mg-bridges enables the side process of diborane generation. It means that the size and denticity of the ligand directly affects the amount of released diborane. In general, the larger the ligand and the higher its denticity, the smaller is amount of diborane produced. The new compound Mg(BH4)2 × diglyme decomposes without diborane formation that allows one to be considered as a new promising chemical hydrogen storage compound for the practical usage.

Unexpected dimerization of isoprene in a gas chromatography inlet. A study by gas chromatography/mass spectrometry coupling.

PubMed

Estevez, Yannick; Gardrat, Christian; Berthelot, Karine; Grau, Etienne; De Jeso, Bernard; Ouardad, Samira; Peruch, Frédéric

2014-02-28

During analysis of pure isoprene by gas chromatography/mass spectrometry (GC-MS) using a programmed temperature vaporization (PTV) inlet, the presence of several isoprene dimers was detected in the total ion chromatograms (TICs). This study intends to determine the part of the instrument where dimerization occurs and the relative importance of the dimer amounts under different experimental conditions. The reference thermal dimerization of isoprene gives four six-membered cyclic dimers and two eight-membered ones. In all samples containing different amounts of freshly distilled isoprene, only peaks corresponding to the former appeared in TICs. For the same temperature, their amounts increase as the concentration of injected isoprene increases. The main products are diprene (from 80 to 100%) of the total dimers and dipentene (from 1 to 14%). The sum of the two other dimers is never higher than 6%. In conclusion, isomeric dimers are produced through a dimerization in the inlet. No dimerization of isoprene occurs in the mass spectrometer source. Then care is needed when analyzing terpenic compounds in the presence of isoprene by GC-MS because structures, retention times and mass spectra of diprene and dipentene are close. Copyright © 2014 Elsevier B.V. All rights reserved.

Prevalence of Helicobacter Pylori in Gastric Fluid in the Surgical Patient

DTIC Science & Technology

1998-05-01

potential in low pH (Tomb et al. 1997). Helicobacter pylori produces significant amounts of urease which cleaves urea into ammonia and carbon dioxide...The presence of urease is one of the biochemical markers used to help identify the presence of H. pylori. (Blaser, 1996). Helicobacter is a genus...gastric lumen it is immersed in acidic gastric juice where small amounts of urea are present. Helicobacter pylori produces urease which breaks down the

Prevalence of Helicobacter Pylori in Gastric Fluid in the Surgical Patient

DTIC Science & Technology

1998-01-01

of five percent. This percentage closely matches the oxygen level found in the stomach’s mucous layer . It has an electropositive internal milieu which...amounts of urease which cleaves urea into ammonia and carbon dioxide. The presence of urease is one of the biochemical markers used to help identify...in acidic gastric juice where small amounts of urea are present. Helicobacter pylorl produces urease which breaks down the urea and produces ammonia

Carbon utilization by fruit limits shoot growth in alternate-bearing citrus trees.

PubMed

Martínez-Alcántara, Belén; Iglesias, Domingo J; Reig, Carmina; Mesejo, Carlos; Agustí, Manuel; Primo-Millo, Eduardo

2015-03-15

Fruit load in alternate-bearing citrus trees is reported to alter shoot number and growth during spring, summer, and autumn flushes, and the source-sink balance, which affects the storage and mobilization of reserve nutrients. The aim of this work was to assess the extent of shoot growth inhibition resulting from the presence of fruits in 'Moncada' mandarin trees loaded with fruit (ON) or with very light fruit load (OFF), and to identify the role of carbohydrates and nitrogenous compounds in the competition between fruits and shoots. Growth of reproductive and vegetative organs was measured on a monthly basis. (13)C- and (15)N-labeled compounds were supplied to trace the allocation of reserve nutrients and subsequent translocation from source to sink. At the end of the year, OFF trees produced more abundant flushes (2.4- and 4.9-fold higher in number and biomass, respectively) than ON trees. Fruits from ON trees accumulated higher C amounts at the expense of developing flushes, whereas OFF trees exhibited the opposite pattern. An inverse relationship was identified between the amount of C utilized by fruits and vegetative flush growth. (13)C-labeling revealed an important role for mature leaves of fruit-bearing branches in supporting shoot/fruit growth, and the elevated sink strength of growing fruits on shoots. N availability for vegetative shoots was not affected by the presence or absence of fruits, which accumulated important amounts of (15)N. In conclusion, our results show that shoot growth is resource-limited as a consequence of fruit development, and vegetative-growth inhibition is caused by photoassimilate limitation. The competence for N is not a decisive factor in limiting vegetative growth under the experimental conditions of this study. Copyright © 2014 Elsevier GmbH. All rights reserved.

Cover crops influence soil microorganisms and phytoextraction of copper from a moderately contaminated vineyard.

PubMed

Mackie, K A; Schmidt, H P; Müller, T; Kandeler, E

2014-12-01

We investigated the ability of summer (Avena sativa [oat], Trifolium incarnatum [crimson clover], Chenopodium [goosefoot]) and winter (Vicia villosa [hairy vetch], Secale Cereale L. [Rye], Brassica napus L. partim [rape]) cover crops, including a mixed species treatment, to extract copper from an organic vineyard soil in situ and the microbial communities that may support it. Clover had the highest copper content (14.3mgCukg(-1) DM). However, it was the amount of total biomass production that determined which species was most effective at overall copper removal per hectare. The winter crop rye produced significantly higher amounts of biomass (3532kgDMha(-1)) and, therefore, removed significantly higher amounts of copper (14,920mgCuha(-1)), despite less accumulation of copper in plant shoots. The maximum annual removal rate, a summation of best performing summer and winter crops, would be 0.033kgCuha(-1)y(-1). Due to this low annual extraction efficiency, which is less than the 6kgCuha(-1)y(-1) permitted for application, phytoextraction cannot be recommended as a general method of copper extraction from vineyards. Copper concentration did not influence aboveground or belowground properties, as indicated by sampling at two distances from the grapevine row with different soil copper concentrations. Soil microorganisms may have become tolerant to the copper levels at this site. Microbial biomass and soil enzyme activities (arylsulfatase and phosphatase) were instead driven by seasonal fluxes of resource pools. Gram+ bacteria were associated with high soil moisture, while fungi seemed to be driven by extractable carbon, which was linked to high plant biomass. There was no microbial group associated with the increased phytoextraction of copper. Moreover, treatment did not influence the abundance, activity or community structure of soil microorganisms. Copyright © 2014 Elsevier B.V. All rights reserved.

Chemistry and phase evolution during roasting of toxic thallium-bearing pyrite.

PubMed

Lopez-Arce, Paula; Garcia-Guinea, Javier; Garrido, Fernando

2017-08-01

In the frame of a research project on microscopic distribution and speciation of geogenic thallium (Tl) from contaminated mine soils, Tl-bearing pyrite ore samples from Riotinto mining district (Huelva, SW Spain) were experimentally fired to simulate a roasting process. Concentration and volatility behavior of Tl and other toxic heavy metals was determined by quantitative ICP-MS, whereas semi-quantitative mineral phase transitions were identified by in situ thermo X-Ray Diffraction (HT-XRD) and Scanning Electron Microscopy with Energy Dispersive Spectroscopy (SEM-EDS) analyses after each firing temperature. Sample with initial highest amount of quartz (higher Si content), lowest quantity of pyrite and traces of jarosite (lower S content) developed hematite and concentrated Tl (from 10 up to 72 mg kg -1 ) after roasting at 900 °C in an oxidizing atmosphere. However, samples with lower or absent quartz content and higher pyrite amount mainly developed magnetite, accumulating Tl between 400 and 500 °C and releasing Tl from 700 up to 900 °C (from 10-29 mg kg -1 down to 4-1 mg kg -1 ). These results show the varied accumulative, or volatile, behaviors of one of the most toxic elements for life and environment, in which oxidation of Tl-bearing Fe sulfides produce Fe oxides wastes with or without Tl. The initial chemistry and mineralogy of pyrite ores should be taken into account in coal-fired power stations, cement or sulfuric acid production industry involving pyrite roasting processes, and steel, brick or paint industries, which use iron ore from roasted pyrite ash, where large amounts of Tl entail significant environmental pollution. Copyright © 2017 Elsevier Ltd. All rights reserved.

The effect of clay catalyst on the chemical composition of bio-oil obtained by co-pyrolysis of cellulose and polyethylene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solak, Agnieszka; Rutkowski, Piotr, E-mail: piotr.rutkowski@pwr.wroc.pl

2014-02-15

Highlights: • Non-catalytic and catalytic fast pyrolysis of cellulose/polyethylene blend was carried out in a laboratory scale reactor. • Optimization of process temperature was done. • Optimization of clay catalyst type and amount for co-pyrolysis of cellulose and polyethylene was done. • The product yields and the chemical composition of bio-oil was investigated. - Abstract: Cellulose/polyethylene (CPE) mixture 3:1, w/w with and without three clay catalysts (K10 – montmorillonite K10, KSF – montmorillonite KSF, B – Bentonite) addition were subjected to pyrolysis at temperatures 400, 450 and 500 °C with heating rate of 100 °C/s to produce bio-oil with highmore » yield. The pyrolytic oil yield was in the range of 41.3–79.5 wt% depending on the temperature, the type and the amount of catalyst. The non-catalytic fast pyrolysis at 500 °C gives the highest yield of bio-oil (79.5 wt%). The higher temperature of catalytic pyrolysis of cellulose/polyethylene mixture the higher yield of bio-oil is. Contrarily, increasing amount of montmorillonite results in significant, almost linear decrease in bio-oil yield followed by a significant increase of gas yield. The addition of clay catalysts to CPE mixture has a various influence on the distribution of bio-oil components. The addition of montmorillonite K10 to cellulose/polyethylene mixture promotes the deepest conversion of polyethylene and cellulose. Additionally, more saturated than unsaturated hydrocarbons are present in resultant bio-oils. The proportion of liquid hydrocarbons is the highest when a montmorillonite K10 is acting as a catalyst.« less

7 CFR 4288.132 - Payment adjustments.

Code of Federal Regulations, 2013 CFR

2013-01-01

... RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE PAYMENT PROGRAMS Advanced Biofuel Payment Program... to the advanced biofuel producer if there is a difference between the amount actually produced and...

7 CFR 4288.132 - Payment adjustments.

Code of Federal Regulations, 2012 CFR

2012-01-01

... RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE PAYMENT PROGRAMS Advanced Biofuel Payment Program... to the advanced biofuel producer if there is a difference between the amount actually produced and...

Measurement and validation of measures for impulsive food choice across obese and healthy-weight individuals.

PubMed

Hendrickson, Kelsie L; Rasmussen, Erin B; Lawyer, Steven R

2015-07-01

The present study established a brief measure of delay discounting for food, the Food Choice Questionnaire (FCQ), and compared it to another more established measure of food discounting that uses the adjusting amount (AA) procedure. One hundred forty-four undergraduate participants completed either two measures of hypothetical food discounting (a computerized food AA procedure or the FCQ) or two measures of hypothetical money discounting [a computerized monetary AA procedure or the Monetary Choice questionnaire (MCQ)]. The money condition was used as a replication of previous work. Results indicated that the FCQ yielded consistent data that strongly correlated with the AA food discounting task. Moreover, a magnitude effect was found with the FCQ, such that smaller amounts of food were discounted more steeply than larger amounts. In addition, individuals with higher percent body fat (PBF) discounted food more steeply than individuals with lower PBF. The MCQ, which also produced a magnitude effect, and the monetary adjusting amount procedure yielded data that were orderly, consistent, and correlated strongly with one another, replicating previous literature. This study is the first to show that a novel measure of food discounting (the FCQ) yields consistent data strongly correlated with an established measure of food discounting and is sensitive to PBF. Moreover, the FCQ is easier and quicker to administer than the AA procedure, which may interest researchers who use discounting tasks in food-related research. Copyright © 2015 Elsevier Ltd. All rights reserved.

Use of $gamma$ irradiation to prevent aflatoxin production in bread

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bullerman, L.B.; Barnhart, H.M.; Hartung, T.E.

Irradiation doses of 100 and 200 Krad reduced the growth of Aspergillus parasiticus in bread stored for 10 days at 254DEC. With bread stored longer than 2 wk, mold growth in irradiated samples tended to approach the amount which occurred in the non-irradiated controls. Mold strain NRRL 3000 seemed slightly more sensitive to irradiation-than strain NRRL 2999. A 200 Krad dose prevented anatoxin production by either strain at both high and low levels of inoculation with spores in bread stored for 10 days, except in one case where a very low level of anatoxins was detected. At 100 Krad, breadmore » inoculated with 102 spores/ slice contained none to low concentrations of anatoxins after storage for 10 days, but with 106 spores/slice higher amounts of toxins were detected. When ihe inoculated bread was stored for periods up to 6 wk, the 200 Krad treatment prevented aflatoxin production in all bread samples containing 10/sup 2/ spores/ slice, and in almost all samples containing 10/sup 6/ spores/ slice. The 100 Krad treatment also prevented aflatoxin production during 6 wk of storage in bread that contained 10/sup 2/ spores/ slice. However, with 10/sup 6/ spores/ slice both strains were capable of producing very high amounts of aflatoxins after irradiation nt 100 Krad. At 1, 2 and 6 wk of storage, these amounts were greater than the unirradiated controls, suggesting possible stimulation of aflatoxin production. (auth)« less

The Relative Importance of Methanogenesis in the Decomposition of Organic Matter in Northern Peatlands

NASA Technical Reports Server (NTRS)

Corbett, J. Elizabeth; Tfaily, Malak M.; Burdige, David J.; Glaser, Paul H.; Chanton, Jeffrey P.

2015-01-01

Using an isotope-mass balance approach and assuming the equimolar production of CO2 and CH4 from methanogenesis (e.g., anaerobic decomposition of cellulose), we calculate that the proportion of total CO2 production from methanogenesis varies from 37 to 83% across a variety of northern peatlands. In a relative sense, methanogenesis was a more important pathway for decomposition in bogs (80 +/- 13% of CO2 production) than in fens (64 +/- 5.7% of CO2 production), but because fens contain more labile substrates they may support higher CH4 production overall. The concentration of CO2 produced from methanogenesis (CO2-meth) can be considered equivalent to CH4 concentration before loss due to ebullition, plant-mediated transport, or diffusion. Bogs produced slightly less CO2-meth than fens (2.9 +/- 1.3 and 3.7 +/- 1.4 mmol/L, respectively). Comparing the quantity of CH4 present to CO2-meth, fens lost slightly more CH4 than bogs (89 +/- 2.8% and 82 +/- 5.3%, respectively) likely due to the presence of vascular plant roots. In collapsed permafrost wetlands, bog moats produced half the amount of CO2-meth (0.8 +/- 0.2mmol/L) relative to midbogs (1.6 +/- 0.6 mmol/L) and methanogenesis was less important (42 +/- 6.6% of total CO2 production relative to 55 +/- 8.1%).We hypothesize that the lower methane production potential in collapsed permafrost wetlands occurs because recently thawed organic substrates are being first exposed to the initial phases of anaerobic decomposition following collapse and flooding. Bog moats lost a comparable amount of CH4 as midbogs (63 +/- 7.0% and 64 +/- 9.3%).

Formation of dioxins from incineration of foods found in domestic garbage.

PubMed

Katami, Takeo; Yasuhara, Akio; Shibamoto, Takayuki

2004-02-15

There has been great concern about the large amounts of garbage produced by domestic households in the modern world. One of the major sources of dioxins (PCDDs, PCDFs, and coplanar PCBs) in the environment is the combustion of domestic waste materials. Exhaust gases from an incinerator, in which mixtures of 67 food items--including fruits, vegetables, pasta, seafoods, meats, and processed foods and seasoned foods--were analyzed for dioxins. Gases collected at the chimney port (9.15 ng/g) contained less total dioxins than those collected at the chamber port (29.1 ng/g). The levels of Cl1-Cl6-PCDDs and Cl1-Cl5-PCDFs were much lower in the gas collected at the chimney port than in the gas collected at the chamber port. The levels of Cl7-Cl8-PCDDs and Cl6-Cl8-PCDFs were higher in the gas collected at the chimney port than in the gas collected at the chamber port. A total of Cl4-Cl8-PCDDs (1.84-3.04 ng/g) comprised over 80% of the total PCDDs formed (2.24-4.00 ng/g). Total PCDFs (16.2-22.6 ng/g) comprised 78-86% of the total dioxins formed (18.9-29.1 ng/g). The PCDFs formed in the greatest amounts were M1CDFs (9.68-10.7 ng/g). Mixtures of commonly consumed food items produced ppb levels of total dioxins in exhaust gases upon combustion, suggesting that incineration of domestic food wastes is one of the sources of dioxins in the environment. A mixture containing some seasoned foods, such as mayonnaise spread on bread, produced more dioxins (29.1 ng/g) than a mixture without seasoned foods did (18.9 ng/g).

Terrestrially derived glomalin-related soil protein quality as a potential ecological indicator in a peri-urban watershed.

PubMed

Sui, Xueyan; Wu, Zhipeng; Lin, Chen; Zhou, Shenglu

2017-07-01

Glomalin, which sequesters substantial amounts of carbon, plays a critical role in sustaining terrestrial biome functions and contributes to the fate of many pollutants from terrestrial to aquatic ecosystems. Despite having focused on the amount of glomalin produced, very few attempts have been made to understand how landscapes and environmental conditions influence glomalin composition and characteristics. This study focused on glomalin-related soil protein (GRSP) exported as storm runoff including eroded sediment and water that was collected before flowing to surface waters in a peri-urban watershed. GRSP characteristics were assessed by Bradford protein analysis, fluorescence spectroscopy combined with parallel factor analysis (PARAFAC), and the determination of aromaticity based on the specific ultraviolet absorption value (280 nm) and molecular weight. General linear models (GLMs) was established by integrating microbial activity, land cover, water temperature, precipitation, and other solution chemical properties to explain the variations in GRSP characteristics. Results showed that a higher GRSP concentration in agricultural reference sites was produced in the form of specific materials with low molecular weight and aromaticity, as well as high percentage of C1 and C5 components which indicate microbial-processed sources, relative to urbanized and forested sites. Compared with forested land, urbanized land clearly produced runoff GRSP with low molecular weight and aromaticity, as well as more degradation of humic-like materials (C3 component). The highest GLM explaining 89% of the variables, including significant variables (p < 0.05) such as microbial activity, water temperature, and water conductivity, was observed for GRSP characteristics. Therefore, changes in eroded soil GRSP quality can serve as an indicator for improving watershed management and thus protecting aquatic ecosystems.

Antioxidant activity and emulsion-stabilizing effect of pectic enzyme treated pectin in soy protein isolate-stabilized oil/water emulsion.

PubMed

Huang, Ping-Hsiu; Lu, Hao-Te; Wang, Yuh-Tai; Wu, Ming-Chang

2011-09-14

The antioxidant activity of pectic enzyme treated pectin (PET-pectin) prepared from citrus pectin by enzymatic hydrolysis and its potential use as a stabilizer and an antioxidant for soy protein isolate (SPI)-stabilized oil in water (O/W) emulsion were investigated. Trolox equivalent antioxidant capacity (TEAC) was found to be positively associated with molecular weight (M(w)) of PET-pectin and negatively associated with degree of esterification (DE) of PET-pectin. PET-pectin (1 kDa and 11.6% DE) prepared from citrus pectin after 24 h of hydrolysis by commercial pectic enzyme produced by Aspergillus niger expressed higher α,α-diphenyl-β-picrylhydrazyl (DPPH) radical scavenging activity, TEAC, and reducing power than untreated citrus pectin (353 kDa and 60% DE). The addition of PET-pectin could increase both emulsifying activity (EA) and emulsion stability (ES) of SPI-stabilized O/W emulsion. When the SPI-stabilized lipid droplet was coated with the mixture of PET-pectin and pectin, the EA and ES of the emulsion were improved more than they were when the lipid droplet was coated with either pectin or PET-pectin alone. The amount of secondary oxidation products (thiobarbituric acid reactive substances) produced in the emulsion prepared with the mixture of SPI and PET-pectin was less than the amount produced in the emulsion prepared with either SPI or SPI/pectin. These results suggest that PET-pectin has an emulsion-stabilizing effect and lipid oxidation inhibition ability on SPI-stabilized emulsion. Therefore, PET-pectin can be used as a stabilizer as well as an antioxidant in plant origin in SPI-stabilized O/W emulsion and thus prolong the shelf life of food emulsion.

Effect of Technology Driven Agricultural Land Use Change on Regional Hydroclimate

NASA Astrophysics Data System (ADS)

Arritt, R. W.; Sines, T. R.; Groisman, P. Y.; Gelder, B. K.

2017-12-01

During the mid-20th century motorized equipment replaced work animals in the central U.S. This led to a 95% decrease in farmland for producing oats, which had mostly been used as feed for horses. Much of this land was converted to more profitable crops such as soybeans and maize. The same period also saw a strong shift of the central U.S. precipitation intensity spectrum toward heavier events. Was this a coincidence, or is there a causal relationship? We investigate possible connections between this technology-driven land use change and regional hydroclimate by performing multi-decadal simulations over the central U.S. using the WRF-ARW regional climate model coupled with the Community Land Model (CLM 4.5). Cropland planted in maize, soybean, winter wheat, small grains (which includes oats and spring wheat), and other C3 and C4 crops were reconstructed on a decade by decade basis from 1940-2010 using county-level crop data. These crop distributions were used as land surface boundary conditions for two multi-decadal regional climate simulations, one with 1940s land use and another with modern (circa 2010) land use. Modern land use produced a shift in the simulated daily precipitation intensity spectrum toward heavy events, with higher frequencies of heavy precipitation amounts and lower frequencies of light amounts compared to 1940s land use. The results suggest that replacement of work animals by mechanized transport led to land use changes that produced about 10-30% of the observed trend toward more intense precipitation over the central United States. We therefore recommend that policy- and technology-driven changes in crop type be taken into account when projecting future climate and water resources.

The relative importance of methanogenesis in the decomposition of organic matter in northern peatlands

NASA Astrophysics Data System (ADS)

Corbett, J. Elizabeth; Tfaily, Malak M.; Burdige, David J.; Glaser, Paul H.; Chanton, Jeffrey P.

2015-02-01

Using an isotope-mass balance approach and assuming the equimolar production of CO2 and CH4 from methanogenesis (e.g., anaerobic decomposition of cellulose), we calculate that the proportion of total CO2 production from methanogenesis varies from 37 to 83% across a variety of northern peatlands. In a relative sense, methanogenesis was a more important pathway for decomposition in bogs (80 ± 13% of CO2 production) than in fens (64 ± 5.7% of CO2 production), but because fens contain more labile substrates they may support higher CH4 production overall. The concentration of CO2 produced from methanogenesis (CO2-meth) can be considered equivalent to CH4 concentration before loss due to ebullition, plant-mediated transport, or diffusion. Bogs produced slightly less CO2-meth than fens (2.9 ± 1.3 and 3.7 ± 1.4 mmol/L, respectively). Comparing the quantity of CH4 present to CO2-meth, fens lost slightly more CH4 than bogs (89 ± 2.8% and 82 ± 5.3%, respectively) likely due to the presence of vascular plant roots. In collapsed permafrost wetlands, bog moats produced half the amount of CO2-meth (0.8 ± 0.2 mmol/L) relative to midbogs (1.6 ± 0.6 mmol/L) and methanogenesis was less important (42 ± 6.6% of total CO2 production relative to 55 ± 8.1%). We hypothesize that the lower methane production potential in collapsed permafrost wetlands occurs because recently thawed organic substrates are being first exposed to the initial phases of anaerobic decomposition following collapse and flooding. Bog moats lost a comparable amount of CH4 as midbogs (63 ± 7.0% and 64 ± 9.3%).

Robust effects of cloud superparameterization on simulated daily rainfall intensity statistics across multiple versions of the Community Earth System Model

DOE PAGES

Kooperman, Gabriel J.; Pritchard, Michael S.; Burt, Melissa A.; ...

2016-02-01

This study evaluates several important statistics of daily rainfall based on frequency and amount distributions as simulated by a global climate model whose precipitation does not depend on convective parameterization—Super-Parameterized Community Atmosphere Model (SPCAM). Three superparameterized and conventional versions of CAM, coupled within the Community Earth System Model (CESM1 and CCSM4), are compared against two modern rainfall products (GPCP 1DD and TRMM 3B42) to discriminate robust effects of superparameterization that emerge across multiple versions. The geographic pattern of annual-mean rainfall is mostly insensitive to superparameterization, with only slight improvements in the double-ITCZ bias. However, unfolding intensity distributions reveal several improvementsmore » in the character of rainfall simulated by SPCAM. The rainfall rate that delivers the most accumulated rain (i.e., amount mode) is systematically too weak in all versions of CAM relative to TRMM 3B42 and does not improve with horizontal resolution. It is improved by superparameterization though, with higher modes in regions of tropical wave, Madden-Julian Oscillation, and monsoon activity. Superparameterization produces better representations of extreme rates compared to TRMM 3B42, without sensitivity to horizontal resolution seen in CAM. SPCAM produces more dry days over land and fewer over the ocean. Updates to CAM’s low cloud parameterizations have narrowed the frequency peak of light rain, converging toward SPCAM. Poleward of 50°, where more rainfall is produced by resolved-scale processes in CAM, few differences discriminate the rainfall properties of the two models. Lastly, these results are discussed in light of their implication for future rainfall changes in response to climate forcing.« less

Forming artificial soils from waste materials for mine site rehabilitation

NASA Astrophysics Data System (ADS)

Yellishetty, Mohan; Wong, Vanessa; Taylor, Michael; Li, Johnson

2014-05-01

Surface mining activities often produce large volumes of solid wastes which invariably requires the removal of significant quantities of waste rock (overburden). As mines expand, larger volumes of waste rock need to be moved which also require extensive areas for their safe disposal and containment. The erosion of these dumps may result in landform instability, which in turn may result in exposure of contaminants such as trace metals, elevated sediment delivery in adjacent waterways, and the subsequent degradation of downstream water quality. The management of solid waste materials from industrial operations is also a key component for a sustainable economy. For example, in addition to overburden, coal mines produce large amounts of waste in the form of fly ash while sewage treatment plants require disposal of large amounts of compost. Similarly, paper mills produce large volumes of alkaline rejected wood chip waste which is usually disposed of in landfill. These materials, therefore, presents a challenge in their use, and re-use in the rehabilitation of mine sites and provides a number of opportunities for innovative waste disposal. The combination of solid wastes sourced from mines, which are frequently nutrient poor and acidic, with nutrient-rich composted material produced from sewage treatment and alkaline wood chip waste has the potential to lead to a soil suitable for mine rehabilitation and successful seed germination and plant growth. This paper presents findings from two pilot projects which investigated the potential of artificial soils to support plant growth for mine site rehabilitation. We found that pH increased in all the artificial soil mixtures and were able to support plant establishment. Plant growth was greatest in those soils with the greatest proportion of compost due to the higher nutrient content. These pot trials suggest that the use of different waste streams to form an artificial soil can potentially be used in mine site rehabilitation where there is a nutrient-rich source of waste.

Insights into isoprene production using the cyanobacterium Synechocystis sp. PCC 6803.

PubMed

Pade, Nadin; Erdmann, Sabrina; Enke, Heike; Dethloff, Frederik; Dühring, Ulf; Georg, Jens; Wambutt, Juliane; Kopka, Joachim; Hess, Wolfgang R; Zimmermann, Ralf; Kramer, Dan; Hagemann, Martin

2016-01-01

Cyanobacteria are phototrophic prokaryotes that convert inorganic carbon as CO2 into organic compounds at the expense of light energy. They need only inorganic nutrients and can be cultivated to high densities using non-arable land and seawater. This has made cyanobacteria attractive organisms for the production of biofuels and chemical feedstock. Synechocystis sp. PCC 6803 is one of the most widely used cyanobacterial model strains. Based on its available genome sequence and genetic tools, Synechocystis has been genetically modified to produce different biotechnological products. Efficient isoprene production is an attractive goal because this compound is widely used as chemical feedstock. Here, we report on our attempts to generate isoprene-producing strains of Synechocystis using a plasmid-based strategy. As previously reported, a codon-optimized plant isoprene synthase (IspS) was expressed under the control of different Synechocystis promoters that ensure strong constitutive or light-regulated ispS expression. The expression of the ispS gene was quantified by qPCR and Western blotting, while the amount of isoprene was quantified using GC-MS. In addition to isoprene measurements in the headspace of closed culture vessels, single photon ionization time-of-flight mass spectrometry (SPI-MS) was applied, which allowed online measurements of isoprene production in open-cultivation systems under various conditions. Under standard conditions, a good correlation existed between ispS expression and isoprene production rate. The cultivation of isoprene production strains under NaCl-supplemented conditions decreased isoprene production despite enhanced ispS mRNA levels. The characterization of the metabolome of isoprene-producing strains indicated that isoprene production might be limited by insufficient precursor levels. Transcriptomic analysis revealed the upregulation of mRNA and regulatory RNAs characteristic of acclimation to metabolic stress. Our best production strains produced twofold higher isoprene amounts in the presence of low NaCl concentrations than previously reported strains. These results will guide future attempts to establish isoprene production in cyanobacterial hosts.

A study to determine whether cavitation occurs around dental ultrasonic scaling instruments.

PubMed

Lea, S C; Price, G J; Walmsley, A D

2005-02-01

The aim of this investigation was to determine if cavitation occurred around dental ultrasonic scalers and to estimate the amount of cavitation occurring. Three styles of tip (3 x TFI-10, 3 x TFI-3, 3 x TFI-1) were used, in conjunction with a Cavitron SPS ultrasonic generator (Dentsply, USA), to insonate terephthalic acid solution. The hydroxyl radical, [*OH], concentration, produced due to cavitation from the scaler tips, was monitored by fluorescence spectroscopy. Cavitational activity was enhanced at higher power settings and at longer operating times. The tip dimensions and geometry as well as the generator power setting are both important factors that affect the production of cavitation.

Pulse-spreading harmonic complex as an alternative carrier for vocoder simulations of cochlear implants.

PubMed

Mesnildrey, Quentin; Hilkhuysen, Gaston; Macherey, Olivier

2016-02-01

Noise- and sine-carrier vocoders are often used to acoustically simulate the information transmitted by a cochlear implant (CI). However, sine-waves fail to mimic the broad spread of excitation produced by a CI and noise-bands contain intrinsic modulations that are absent in CIs. The present study proposes pulse-spreading harmonic complexes (PSHCs) as an alternative acoustic carrier in vocoders. Sentence-in-noise recognition was measured in 12 normal-hearing subjects for noise-, sine-, and PSHC-vocoders. Consistent with the amount of intrinsic modulations present in each vocoder condition, the average speech reception threshold obtained with the PSHC-vocoder was higher than with sine-vocoding but lower than with noise-vocoding.

Production of sintered porous metal fluoride pellets

DOEpatents

Anderson, L.W.; Stephenson, M.J.

1973-12-25

Porous pellets characterized by a moderately reactive crust and a softer core of higher reactivity are produced by forming agglomerates containing a metal fluoride powder and a selected amount ofwater. The metal fluoride is selected to be sinterable and essentially non-reactive with gaseous fluorinating agents. The agglomerates are contacted with a gaseous fluorinating agent under controlled conditions whereby the heat generated by localized reaction of the agent and water is limited to values effccting bonding by localized sintering. Porous pellets composed of cryolite (Na/sub 3/AlF/sub 6/) can be used to selectively remove trace quantities of niobium pentafluoride from a feed gas consisting predominantly of uranium hexafluoride. (Official Gazette)

Effects of two-temperature model on cascade evolution in Ni and NiFe

DOE PAGES

Samolyuk, German D.; Xue, Haizhou; Bei, Hongbin; ...

2016-07-05

We perform molecular dynamics simulations of Ni ion cascades in Ni and equiatomic NiFe under the following conditions: (a) classical molecular dynamics (MD) simulations without consideration of electronic energy loss, (b) classical MD simulations with the electronic stopping included, and (c) using the coupled two-temperature MD (2T-MD) model that incorporates both the electronic stopping and the electron-phonon interactions. Our results indicate that the electronic effects are more profound in the higher-energy cascades, and that the 2T-MD model results in a smaller amount of surviving damage and smaller defect clusters, while less damage is produced in NiFe than in Ni.

Biomechanical evaluation of fixation of intra-articular fractures of the distal part of the radius in cadavera: Kirschner wires compared with calcium-phosphate bone cement.

PubMed

Yetkinler, D N; Ladd, A L; Poser, R D; Constantz, B R; Carter, D

1999-03-01

The purpose of this study was to compare the biomechanical efficacy of an injectable calcium-phosphate bone cement (Skeletal Repair System [SRS]) with that of Kirschner wires for the fixation of intraarticular fractures of the distal part of the radius. Colles fractures (AO pattern, C2.1) were produced in ten pairs of fresh-frozen human cadaveric radii. One radius from each pair was randomly chosen for stabilization with SRS bone cement. These ten radii were treated with open incision, impaction of loose cancellous bone with use of a Freer elevator, and placement of the SRS bone cement by injection. In the ten control specimens, the fracture was stabilized with use of two horizontal and two oblique Kirschner wires. The specimens were cyclically loaded to a peak load of 200 newtons for 2000 cycles to evaluate the amount of settling, or radial shortening, under conditions simulating postoperative loading with the limb in a cast. Each specimen then was loaded to failure to determine its ultimate strength. The amount of radial shortening was highly variable among the specimens, but it was consistently higher in the Kirschner-wire constructs than in the bone fixed with SRS bone cement within each pair of radii. The range of shortening for all twenty specimens was 0.18 to 4.51 millimeters. The average amount of shortening in the SRS constructs was 50 percent of that in the Kirschner-wire constructs (0.51+/-0.34 compared with 1.01+/-1.23 millimeters; p = 0.015). With the numbers available, no significant difference in ultimate strength was detected between the two fixation groups. This study showed that fixation of an intra-articular fracture of the distal part of a cadaveric radius with biocompatible calcium-phosphate bone cement produced results that were biomechanically comparable with those produced by fixation with Kirschner wires. However, the constructs that were fixed with calcium-phosphate bone cement demonstrated less shortening under simulated cyclic load-bearing.

30 CFR 260.102 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... amount or value of the production saved, removed, or sold. Lease period means the time from lease... rate payable to the United States, as specified in the lease, in the amount or value of the production... title.) Production period means the period during which the amount of oil and gas produced from a tract...

Factors Affecting Pheromone Production by the Pepper Weevil, Anthonomus eugenii Cano (Coleoptera: Curculionidae) and Collection Efficiency

PubMed Central

Eller, Fred J.; Palmquist, Debra E.

2014-01-01

Several factors affecting pheromone production by male pepper weevils, Anthonomus eugenii Cano (Coleoptera: Curculionidae) as well as collection efficiency were investigated. Factors studied included: porous polymer adsorbents (Tenax versus Super Q), male age, time of day, male density, and male diet. Super Q was found to be a superior adsorbent for the male-produced alcohols and geranic acid as well as the plant-produced E-β-ocimene. Pheromone production increased with male age up to about age 15 days old and then tapered off. Male pepper weevils produced the highest amount of pheromone between noon and 2 pm (i.e., 4 to 6 h after “lights on”) and were producing ca. 800 ng/h during this period. Thereafter, pheromone production decreased and was extremely low during the scotophase (i.e., ca. 12 ng/h). Male pepper weevil density had a significant effect on both release rate and pheromone composition. Pheromone production on a per male basis was highest for individual males and the percentage of geranic acid in the blend was lowest for individual males. Male pepper weevils produced only extremely low amounts of pheromone when feeding on artificial diet; however, they produced very high amounts when on fresh peppers. Together, this information will be useful in designing better attractant lures for pepper weevils. PMID:26462948

Evaluation of nutraceutical and antinutritional properties in barnyard and finger millet varieties grown in Himalayan region.

PubMed

Panwar, Priyankar; Dubey, Ashutosh; Verma, A K

2016-06-01

Five elite varieties of barnyard (Echinochloa frumentacea) and finger (Eleusine coracana) growing at northwestern Himalaya were investigated for nutraceutical and antinutritional properties. Barnyard millet contained higher amount of crude fiber, total dietary fiber, tryptophan content, total carotenoids, α-tocopherol compared to the finger millet whereas the finger millet contains higher amount of methionine and ascorbic acid as compared to the barnyard millet. The secondary metabolites of biological functions were analyzed and found that barnyard millet contained the higher amount of polyphenols, tannins and ortho-dihydroxy phenol content compared to finger millet. Among antinutitional compounds barnyard millet contained lower phytic acid content compare to finger millet whereas no significant difference in trypsin inhibition activity of barnyard millet and finger millet varieties were found. Barnyard millet contained higher acid phosphatase, α-galactosidase and α-amylase inhibitor activity compared to finger millet. Finger millet seeds contained about 10-13 folds higher calcium content and double amount of manganese content in comparison to barnyard millet seeds. Present study suggests that barnyard millet varieties studied under present investigation were found nutritionally superior compared to finger millet varieties.

Linagliptin

MedlinePlus

... because the body does not produce or use insulin normally). Linagliptin is in a class of medications ... condition in which the body does not produce insulin and, therefore, cannot control the amount of sugar ...

Response surface optimization of culture medium for enhanced docosahexaenoic acid production by a Malaysian thraustochytrid.

PubMed

Manikan, Vidyah; Kalil, Mohd Sahaid; Hamid, Aidil Abdul

2015-02-27

Docosahexaenoic acid (DHA, C22:6n-3) plays a vital role in the enhancement of human health, particularly for cognitive, neurological, and visual functions. Marine microalgae, such as members of the genus Aurantiochytrium, are rich in DHA and represent a promising source of omega-3 fatty acids. In this study, levels of glucose, yeast extract, sodium glutamate and sea salt were optimized for enhanced lipid and DHA production by a Malaysian isolate of thraustochytrid, Aurantiochytrium sp. SW1, using response surface methodology (RSM). The optimized medium contained 60 g/L glucose, 2 g/L yeast extract, 24 g/L sodium glutamate and 6 g/L sea salt. This combination produced 17.8 g/L biomass containing 53.9% lipid (9.6 g/L) which contained 44.07% DHA (4.23 g/L). The optimized medium was used in a scale-up run, where a 5 L bench-top bioreactor was employed to verify the applicability of the medium at larger scale. This produced 24.46 g/L biomass containing 38.43% lipid (9.4 g/L), of which 47.87% was DHA (4.5 g/L). The total amount of DHA produced was 25% higher than that produced in the original medium prior to optimization. This result suggests that Aurantiochytrium sp. SW1 could be developed for industrial application as a commercial DHA-producing microorganism.

An overview on exploration and environmental impact of unconventional gas sources and treatment options for produced water.

PubMed

Silva, Tânia L S; Morales-Torres, Sergio; Castro-Silva, Sérgio; Figueiredo, José L; Silva, Adrián M T

2017-09-15

Rising global energy demands associated to unbalanced allocation of water resources highlight the importance of water management solutions for the gas industry. Advanced drilling, completion and stimulation techniques for gas extraction, allow more economical access to unconventional gas reserves. This stimulated a shale gas revolution, besides tight gas and coalbed methane, also causing escalating water handling challenges in order to avoid a major impact on the environment. Hydraulic fracturing allied to horizontal drilling is gaining higher relevance in the exploration of unconventional gas reserves, but a large amount of wastewater (known as "produced water") is generated. Its variable chemical composition and flow rates, together with more severe regulations and public concern, have promoted the development of solutions for the treatment and reuse of such produced water. This work intends to provide an overview on the exploration and subsequent environmental implications of unconventional gas sources, as well as the technologies for treatment of produced water, describing the main results and drawbacks, together with some cost estimates. In particular, the growing volumes of produced water from shale gas plays are creating an interesting market opportunity for water technology and service providers. Membrane-based technologies (membrane distillation, forward osmosis, membrane bioreactors and pervaporation) and advanced oxidation processes (ozonation, Fenton, photocatalysis) are claimed to be adequate treatment solutions. Copyright © 2017 Elsevier Ltd. All rights reserved.

An ascomycota coculture in batch bioreactor is better than polycultures for cellulase production.

PubMed

Hernández, Christian; Milagres, Adriane M F; Vázquez-Marrufo, Gerardo; Muñoz-Páez, Karla María; García-Pérez, José Antonio; Alarcón, Enrique

2018-07-01

Efficient hydrolysis of holocellulose depends on a proper balance between cellulase (endoglucanase, exoglucanase, β-glucosidase) and xylanase activities. The present study aimed to induce the production of cellulases and xylanases using liquid cultures (one, two, three, and four fungal strains on the same bioreactor) of wild strains of Trichoderma harzianum, Aspergillus niger, and Fusarium oxysporum. The strains were identified by amplification and analysis of the ITS rDNA region and the obtained sequences were deposited in Genbank. Enzymes (endoglucanase, exoglucansae, β-glucosidase, and xylanase activities) and the profile of extracellular protein isoforms (SDS-PAGE) produced by different fungal combinations (N = 14) were analyzed by Pearson's correlation matrix and principal component analysis (PCA). According to our results, induction of endoglucanase (19.02%) and β-glucosidase (6.35%) were obtained after 4 days when A. niger and F. oxysporum were cocultured. The combination of A. niger-T. harzianum produced higher endoglucanase in a shorter time than monocultures. On the contrary, when more than two strains were cultured in the same reactor, the relationships of competition were established, trending to diminish the amount of enzymes and the extracellular protein isoforms produced. The xylanase production was sensible to stress produced by mixed cultures, decreasing their activity. This is important when the aim is to produce cellulase-free xylanase. In addition, exoglucanase activity did not change in the combinations tested.

Upper-plate splay fault earthquakes along the Arakan subduction belt recorded by uplifted coral microatolls on northern Ramree Island, western Myanmar (Burma)

NASA Astrophysics Data System (ADS)

Shyu, J. Bruce H.; Wang, Chung-Che; Wang, Yu; Shen, Chuan-Chou; Chiang, Hong-Wei; Liu, Sze-Chieh; Min, Soe; Aung, Lin Thu; Than, Oo; Tun, Soe Thura

2018-02-01

Upper-plate structures that splay out from the megathrusts are common features along major convergent plate boundaries. However, their earthquake and tsunami hazard potentials have not yet received significant attention. In this study, we identified at least one earthquake event that may have been produced by an upper-plate splay fault offshore western Myanmar, based on U-Th ages of uplifted coral microatolls. This event is likely an earthquake that was documented historically in C.E. 1848, with an estimated magnitude between 6.8 and 7.2 based on regional structural characteristics. Such magnitude is consistent with the observed co-seismic uplift amount of ∼0.5 m. Although these events are smaller in magnitude than events produced by megathrusts, they may produce higher earthquake and tsunami hazards for local coastal communities due to their proximity. Our results also indicate that earthquake events with co-seismic uplift along the coast may not necessarily produce a flight of marine terraces. Therefore, using only records of uplifted marine terraces as megathrust earthquake proxies may overlook the importance of upper-plate splay fault ruptures, and underestimate the overall earthquake frequency for future seismic and tsunami hazards along major subduction zones of the world.

Tektites: Origin as melts produced by the impact of small projectiles onto dry targets

NASA Technical Reports Server (NTRS)

Wasson, John T.

1988-01-01

The formation of tektites in general and layered tektites in particular seems to require a very special kind of cratering event. Evidence for the formation of pools of melt free of unmelted clasts has not been reported for the well-studied terrestrial craters such as Manicouagan or Ries. It is suggested that large amounts of relict-free melt were produced only when a sizeable fraction of the cratered target consisted of dry, high-porosity materials such as aeolian sediments. Since dry, high-porosity target materials are always confined to the outer 100 to 200 m of the Earth, the fraction of melt produced melt is probably higher in small (radius 50 to 500 m) craters than in large (r greater than 1 km) craters. Another reason to infer that the Southeast Asian tektites were produced in a multitude of small craters is the wide distribution of layered tektites. The file spans at least 1200 km, which would require ballistic ejection at velocities greater than 2 km s(-1) if all melt was generated in a single crater. It seems impossible to devise a scenario that would lead to the deposition of primary melt as a crystal-free pool at a distance of 600 km from the crater.

Design and manufacture a coconut milk squeezer

NASA Astrophysics Data System (ADS)

Wayan Surata, I.; Gde Tirta Nindhia, Tjokorda; Budyanto, D.; Yulianto, A. E.

2017-05-01

The process of cooking oil production generally is started by grating the ripe coconut meat, then pressing the grated meat to obtain coconut milk, and finally heating the coconut milk to obtain the cooking oil. Pressing mechanism to obtain coconut milk is a very important step and decisive in the process of producing cooking oil. The amount of milk produced depends on the pressure applied at the time of pressing grated coconut. The higher the pressure, the more milk is obtained. Some commercial mechanical pressing tools that available in the market are not efficient due to the working steps too much and take long time per cycle of work. The aims of this study was to design and manufacture a power screw squeezer for the collection of coconut milk. Power screw produces a compressive force in the cylinder to push and press the grated coconut until the end of the cylinder while the coconut milk and coconut dregs flow out simultaneously. Screw press was designed using straight shaft configuration with square profile. Performance test was done to investigate the actual capacity and yield of milk produced. The results showed that squeezer of grated coconut worked well with capacity an average of 13,63 kg/h and coconut milk yield of 58%.

Phytoextraction of risk elements by willow and poplar trees.

PubMed

Kacálková, Lada; Tlustoš, Pavel; Száková, Jiřina

2015-01-01

To characterize the phytoextraction efficiency of two clones of willow trees (Salix x smithiana Willd., Salix rubens) and two clones of poplar trees (Populus nigra x maximowiczii, Populus nigra Wolterson) were planted in contaminated soil (0.4-2.0 mg Cd.kg(-1), 78-313 mg Zn.kg(-1), 21.3-118 mg Cu.kg(-1)). Field experiment was carried out in Czech Republic. The study investigated their ability to accumulate heavy metals (Cd, Zn, and Cu) in harvestable plant parts. The poplars produced higher amount of biomass than willows. Both Salix clones accumulated higher amount of Cd, Zn and Cu in their biomass (maximum 6.8 mg Cd.kg(-1), 909 mg Zn.kg(-1), and 17.7 mg Cu.kg(-1)) compared to Populus clones (maximum 2.06 mg Cd.kg(-1), 463 mg Zn.kg(-1), and 11.8 mg Cu.kg(-1)). There were no significant differences between clones of individual species. BCs for Cd and Zn were greater than 1 (the highest in willow leaves). BCs values of Cu were very low. These results indicate that Salix is more suitable plant for phytoextraction of Cd and Zn than Populus. The Cu phytoextraction potential of Salix and Populus trees was not confirmed in this experiment due to low soil availability of this element.

Elevated O3 enhances the attraction of whitefly-infested tomato plants to Encarsia formosa

PubMed Central

Cui, Hongying; Su, Jianwei; Wei, Jianing; Hu, Yongjian; Ge, Feng

2014-01-01

We experimentally examined the effects of elevated O3 and whitefly herbivory on tomato volatiles, feeding and oviposition preferences of whiteflies and behavioural responses of Encarsia formosa to these emissions on two tomato genotypes, a wild-type (Wt) and a jasmonic acid (JA) defence-enhanced genotype (JA-OE, 35S). The O3 level and whitefly herbivory significantly increased the total amount of volatile organic compounds (VOCs), monoterpenes, green leaf volatiles (GLVs), and aldehyde volatiles produced by tomato plants. The 35S plants released higher amount of total VOCs and monoterpene volatiles than Wt plants under O3+herbivory treatments. The feeding and oviposition bioassays showed that control plants were preferred by adult whiteflies whereas the 35S plants were not preferred by whiteflies. In the Y-tube tests, O3+herbivory treatment genotypes were preferred by adult E. Formosa. The 35S plants were preferred by adult E. formosa under O3, herbivory and O3+herbivory treatments. Our results demonstrated that elevated O3 and whitefly herbivory significantly increased tomato volatiles, which attracted E. formosa and reduced whitefly feeding. The 35S plants had a higher resistance to B. tabaci than Wt plant. Such changes suggest that the direct and indirect defences of resistant genotypes, such as 35S, could strengthen as the atmospheric O3 concentration increases. PMID:24939561

Calf's sex, parity and the hour of harvest after calving affect colostrum quality of dairy cows grazing under high tropical conditions.

PubMed

Angulo, Joaquin; Gómez, Luis Miguel; Mahecha, Liliana; Mejía, Estefanía; Henao, Javier; Mesa, Carolina

2015-04-01

High-quality colostrum is an important factor influencing neonatal calf health, and quality assessment is essential to obtain good health results. This research evaluated the effects of the calf's sex, the parity of the cow and the hour of colostrum harvest after parity on the fat, nonfat solids, protein and Ig contents in Holstein colostrum for cows under high grazing conditions in the tropics. The effects of the calf's sex and parity on somatic cell count (SCC) at the first milking postpartum were determined. A comparison was made between a laboratory method and a farm method for the estimation of the fat and protein content of colostrum. Thirty-three cows were sampled in the study. The calf's sex was shown to have an effect on the amount of colostrum, on the concentration of fat, and on the amount of milk produced by lactating Holstein cows; all were higher in cows that gave birth to a female calf. Colostrum protein decreased after the first hour postpartum, and the Ig concentration had a tendency to decrease after 4 h. The cows that had parity 1-2 had lower Ig concentrations and total production of Igs, and higher SCC at the first milking postpartum. Ekomilk was a reliable method to measure the colostrum fat on the farm.

Directional spatial frequency analysis of lipid distribution in atherosclerotic plaque

NASA Astrophysics Data System (ADS)

Korn, Clyde; Reese, Eric; Shi, Lingyan; Alfano, Robert; Russell, Stewart

2016-04-01

Atherosclerosis is characterized by the growth of fibrous plaques due to the retention of cholesterol and lipids within the artery wall, which can lead to vessel occlusion and cardiac events. One way to evaluate arterial disease is to quantify the amount of lipid present in these plaques, since a higher disease burden is characterized by a higher concentration of lipid. Although therapeutic stimulation of reverse cholesterol transport to reduce cholesterol deposits in plaque has not produced significant results, this may be due to current image analysis methods which use averaging techniques to calculate the total amount of lipid in the plaque without regard to spatial distribution, thereby discarding information that may have significance in marking response to therapy. Here we use Directional Fourier Spatial Frequency (DFSF) analysis to generate a characteristic spatial frequency spectrum for atherosclerotic plaques from C57 Black 6 mice both treated and untreated with a cholesterol scavenging nanoparticle. We then use the Cauchy product of these spectra to classify the images with a support vector machine (SVM). Our results indicate that treated plaque can be distinguished from untreated plaque using this method, where no difference is seen using the spatial averaging method. This work has the potential to increase the effectiveness of current in-vivo methods of plaque detection that also use averaging methods, such as laser speckle imaging and Raman spectroscopy.

Supply of fatty acid is one limiting factor in the accumulation of triacylglycerol in developing embryos

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bao, X.; Ohlrogge, J.

1999-08-01

The metabolic factors that determine oil yield in seeds are still not well understood. To begin to examine the limits on triacylglycerol (TAG) production, developing Cuphea lanceolata, Ulmus carpinifolia, and Ulmus parvifolia embryos were incubated with factors whose availability might limit oil accumulation. The addition of glycerol or sucrose did not significantly influence the rate of TAG synthesis. However, the rate of {sup 14}C-TAG synthesis upon addition of 2.1 mM {sup 14}C-decanoic acid (10:0) was approximately four times higher than the in vivo rate of TAG accumulation in C. lanceolata and two times higher than the in vivo rate inmore » U. carpinifolia and U. parvifolia. In C. lanceolata embryos, the highest rate of {sup 14}C-TAG synthesis (14.3 nmol h{sup {minus}1} embryo {sup {minus}1}) was achieved with the addition of 3.6 mM decanoic acid. {sup 14}C-Decanoic acid was incorporated equally well in all three acyl positions of TAG. The results suggest that C. lancelata, U. Carpinifolia, and U. parvifolia embryos have sufficient acyltransferase activities and glycerol-3-phosphate levels to support rates of TAG synthesis in excess of those found in vivo. Consequently, the amount of TAG synthesized in these oilseeds may be in part determined by the amount of fatty acid produced in plastids.« less

Novel adsorbent for DNA adsorption: Fe(3+)-attached sporopollenin particles embedded composite cryogels.

PubMed

Ceylan, Şeyda; Odabaşı, Mehmet

2013-12-01

The aim of this study is to prepare supermacroporous cryogels embedded with Fe(3+)-attached sporopollenin particles (Fe(3++)-ASPs) having large surface area for high DNA adsorption capacity. Supermacroporous poly(2-hydroxyethyl methacrylate) (PHEMA)-based monolithic cryogel column embedded with Fe3+(+)-ASPs was prepared by radical cryo-copolymerization of 2-hydroxyethyl methacrylate (HEMA) with N,N´-methylene- bis-acrylamide (MBAAm) as cross-linker directly in a plastic syringe for DNA adsorption studies. Firstly, Fe3+(+) ions were attached to the sporopollenin particles (SPs), then the supermacroporous PHEMA cryogel with embedded Fe(3++)-ASPs was produced by free radical polymerization using N,N,N´, N´-Tetramethylethylenediamine (TEMED) and ammonium persulfate (APS) as initiator/activator pair in an ice bath. Optimum conditions of adsorption experiments were performed at pH 6.0 (0.02 M Tris buffer containing 0.2 M NaCl), with flow rate of 0.5 mL/min, and at 5°C. The maximum amount of DNA adsorption from aqueous solution was very high (109 mg/g SPs) with initial concentration of 3 mg/mL. It was observed that DNA could be repeatedly adsorbed and desorbed with this composite cryogel without significant loss of adsorption capacity. As a result, higher amounts of DNA adsorbed these composite cryogels are expected to be good candidate for achieving higher removal of anti-DNA antibodies from systemic lupus erythematosus (SLE) patients plasma.

Regenerable Nickel-Functionalized Activated Carbon Cathodes Enhanced by Metal Adsorption to Improve Hydrogen Production in Microbial Electrolysis Cells.

PubMed

Kim, Kyoung-Yeol; Yang, Wulin; Logan, Bruce E

2018-06-07

While nickel is a good alternative to platinum as a catalyst for the hydrogen evolution reaction, it is desirable to reduce the amount of nickel needed for cathodes in microbial electrolysis cells (MECs). Activated carbon (AC) was investigated as a cathode base structure for Ni as it is inexpensive and an excellent adsorbent for Ni, and it has a high specific surface area. AC nickel-functionalized electrodes (AC-Ni) were prepared by incorporating Ni salts into AC by adsorption, followed by cathode fabrication using a phase inversion process using a poly(vinylidene fluoride) (PVDF) binder. The AC-Ni cathodes had significantly higher (∼50%) hydrogen production rates than controls (plain AC) in smaller MECs (static flow conditions) over 30 days of operation, with no performance decrease over time. In larger MECs with catholyte recirculation, the AC-Ni cathode produced a slightly higher hydrogen production rate (1.1 ± 0.1 L-H 2 /L reactor /day) than MECs with Ni foam (1.0 ± 0.1 L-H 2 /L reactor /day). Ni dissolution tests showed that negligible amounts of Ni were lost into the electrolyte at pHs of 7 or 12, and the catalytic activity was restored by simple readsorption using a Ni salt solution when Ni was partially removed by an acid wash.

The use of short and long PCR products for improved detection of prunus necrotic ringspot virus in woody plants.

PubMed

Rosner, A; Maslenin, L; Spiegel, S

1997-09-01

The reverse transcriptase-polymerase chain reaction (RT-PCR) was used for detection of prunus necrotic ringspot virus (PNRSV) in dormant peach and almond trees by the application of two different pairs of primers yielding a short and a long product, respectively. The relative amount of the short (200 base pair, bp) product was higher than the longer (785 bp) product. PNRSV was detected better in plant tissues with a low virus concentration (e.g. dormant trees) by amplification of the short PCR product, whereas the long product was product was produced at higher virus titers. Simultaneous amplification of both short and long products was demonstrated using a three-primer mixture in a single reaction tube. In this assay, amplification of either PCR product indicated the presence of PNRSV-specific sequences in the plant tissue examined, thus covering a wide range of virus concentrations in a single test. Dilution of the RNA extracted from infected plant material resulted in a steep decline in the amplification of both short and long PCR products. In contrast, serial dilutions of the intermediate cDNA template differentially affected the amplification patterns: the relative amount of the short product increased whereas that of the long product decreased. These results may explain the preferential amplification of the short PCR product observed in samples containing low virus concentrations.

The effect of material productivity on scrap reduction on aluminum reduction pot process

NASA Astrophysics Data System (ADS)

Huda, L. N.

2018-02-01

Scrap in the production process is defined as part of production that can not be accepted as the final product due to production failure. The amount of scarp occurring in the reduction pot production process of one of the aluminum smelting furnaces exceeds the acceptance standard of 5 to 10%. This affects the amount of production produced. The purpose of this study is to reduce the amount of scrap produced to increase the productivity of the materials used. The solution is carried-out by making improvements using Lean Six Sigma method. In the initial calculation, material productivity ranged from 0.88. Based on the study, the factors that cause the high amount of scrap produced is the use of Na2O which is inserted into the alumina is different in size and the influence of noise that occurs in pots that are difficult to control. The analysis base on Lean Six Sigma obtained process cycle efficiency (PCE) equal to 86,92% for actual condition. Process improvement is carried-out through define, measure, analyze, improve and control procedure on Na2O feeding process and PCE value decrease 6,05%. This indicates that increased process capability will reduce scrap. A decrease in scrap amount of about 6% will be able to increase material productivity by 0.05%. This indicates that continuous process control is needed to decrease the number of scraps and increase productivity.

Device for quickly sensing the amount of O2 in a combustion product gas

NASA Technical Reports Server (NTRS)

Singh, Jag J. (Inventor); Davis, William T. (Inventor); Puster, Richard L. (Inventor)

1990-01-01

A sensing device comprising an O2 sensor, a pump, a compressor, and a heater is provided to quickly sense the amount of O2 in a combustion product gas. A sample of the combustion product gas is compressed to a pressure slightly above one atmosphere by the compressor. Next, the heater heats the sample between 800 C and 900 C. Next, the pump causes the sample to be flushed against the electrode located in O2 sensor 6000 to 10,000 times per second. Reference air at approximately one atmosphere is provided to the electrode of O2 sensor. Accordingly, the O2 sensor produces a voltage which is proportional to the amount of oxygen in the combustion product gas. This voltage may be used to control the amount of O2 entering into the combustion chamber which produces the combustion product gas.

Association between Symptoms of Irritable Bowel Syndrome and Methane and Hydrogen on Lactulose Breath Test

PubMed Central

Lee, Kang Nyeong; Koh, Dong Hee; Sohn, Won; Lee, Sang Pyo; Jun, Dae Won; Lee, Hang Lak; Yoon, Byung Chul; Choi, Ho Soon; Hahm, Joon Soo

2013-01-01

Whether hydrogen and methane gas produced during lactulose breath test (LBT) are associated with symptoms of irritable bowel syndrome (IBS) is not determined. We aimed to investigate whether hydrogen and methane on LBT are associated with IBS symptoms. Sixty-eight IBS patients meeting the Rome III criteria for IBS, and 55 healthy controls, underwent LBT. The IBS subjects recorded their customary gastrointestinal symptoms on a questionnaire using visual analogue scales. LBT positivity was defined to be above 20 ppm rise of hydrogen or 10 ppm rise of methane within 90 min. Gas amounts produced during LBT were determined by calculating area under the curve of hydrogen and methane excretion. Symptom severity scores were not different between the LBT (+) IBS and LBT (-) IBS subjects and also between methane producers and non-methane producers. Gas amounts produced during LBT were not associated with IBS symptoms, except a weak correlation between total gas amounts and a few IBS symptoms such as bloating (r = 0.324, P = 0.039), flatulence (r = 0.314, P = 0.046) and abdominal pain (r = 0.364, P = 0.018) only in LBT (+) IBS. In conclusion, hydrogen and methane gas on LBT are not useful for predicting the customary symptoms and subtypes of IBS. PMID:23772156

Investigating combustion as a method of processing inedible biomass produced in NASA's biomass production chamber

NASA Technical Reports Server (NTRS)

Dreschel, T. W.; Wheeler, R. M.; Hinkle, C. R.; Sager, J. C.; Knott, W. M.

1991-01-01

The Controlled Ecological Life Support System (CELSS) Breadboard Project at the John F. Kennedy Space Center is a research program to integrate and evaluate biological processes to provide air, water, and food for humans in closed environments for space habitation. This project focuses on the use of conventional crop plants as grown in the Biomass Production Chamber (BPC) for the production and recycling of oxygen, food, and water. The inedible portion of these crops has the potential to be converted to edible biomass or directly to the elemental constituents for direct recycling. Converting inedible biomass directly, by combustion, to carbon dioxide, water, and minerals could provide a baseline for estimating partitioning of the mass balance during recycling in a CELSS. Converting the inedible biomass to carbon dioxide and water requires the same amount of oxygen that was produced by photosynthesis. The oxygen produced during crop growth is just equal to the oxygen required to oxidize all the biomass produced during growth. Thus, the amount of oxygen produced that is available for human consumption is in proportion to the amount of biomass actually utilized by humans. The remaining oxygen must be available to oxidize the rest of the biomass back to carbon dioxide and water or the system will not be a regenerative one.

Model business intelligence system design of quality products by using data mining in R Bakery Company

NASA Astrophysics Data System (ADS)

Fitriana, R.; Saragih, J.; Luthfiana, N.

2017-12-01

R Bakery company is a company that produces bread every day. Products that produced in that company have many different types of bread. Products are made in the form of sweet bread and wheat bread which have different tastes for every types of bread. During the making process, there were defects in the products which the defective product turns into reject product. Types of defects that are produced include burnt, sodden bread and shapeless bread. To find out the information about the defects that have been produced then by applying a designed model business intelligence system to create database and data warehouse. By using model business Intelligence system, it will generate useful information such as how many defect that produced by each of the bakery products. To make it easier to obtain such information, it can be done by using data mining method which data that we get is deep explored. The method of data mining is using k-means clustering method. The results of this intelligence business model system are cluster 1 with little amount of defect, cluster 2 with medium amount of defect and cluster 3 with high amount of defect. From OLAP Cube method can be seen that the defect generated during the 7 months period of 96,744 pieces.

The roles of AMY1 copies and protein expression in human salivary α-amylase activity.

PubMed

Yang, Ze-Min; Lin, Jing; Chen, Long-Hui; Zhang, Min; Chen, Wei-Wen; Yang, Xiao-Rong

2015-01-01

Salivary α-amylase (sAA) activity has been extensively investigated in nutrition and psychology. But few studies were performed to assess the role played by sAA gene (AMY1) copies and protein expression in basal and stimulus-induced sAA activity. The sAA activity, amount and AMY1 copy number were determined from 184 saliva samples pre- and post-citric acid stimulation. Our findings showed that citric acid could induce significant increase in sAA activity, total sAA amount, and glycosylated sAA amount, among which the glycosylated sAA amount had the largest response. The correlation analysis showed that AMY1 copy number, total sAA amount and AMY1 copy number×total sAA amount had significantly positive and successively increasing correlations with sAA activity in unstimulated and stimulated saliva, respectively, and furthermore, we observed higher correlations in unstimulated saliva when compared with the corresponding correlations in stimulated saliva. We also observed significant correlations between glycosylated sAA amount and sAA activity in unstimulated and stimulated saliva, respectively. Interestingly, the correlations were higher in stimulated saliva than in unstimulated saliva, and the correlations between glycosylated sAA amount and sAA activity were higher than that of between total sAA amount and sAA activity in stimulated saliva. Moreover, total sAA amount ratio and glycosylated sAA amount ratio showed significantly positive correlation with sAA activity ratio. AMY1 copy number had no correlation with sAA activity ratio. These findings suggested that AMY1 copy number and sAA amount played crucial roles in sAA activity; however, the roles were attenuated after stimulation due to fortified release of glycosylated sAA. Copyright © 2014 Elsevier Inc. All rights reserved.

Cloning and expression of the gene for bacteriophage T7 RNA polymerase

DOEpatents

Studier, F.W.; Davanloo, P.; Rosenberg, A.H.

1984-03-30

This application describes a means to clone a functional gene for bacteriophage T7 RNA polymerase. Active T7 RNA polymerase is produced from the cloned gene, and a plasmid has been constructed that can produce the active enzyme in large amounts. T7 RNA polymerase transcribes DNA very efficiently and is highly selective for a relatively long promoter sequence. This enzyme is useful for synthesizing large amounts of RNA in vivo or in vitro, and is capable of producing a single RNA selectively from a complex mixture of DNAs. The procedure used to obtain a clone of the T7 RNA polymerase gene can be applied to other T7-like phages to obtain clones that produce RNA polymerases having different promoter specificities, different bacterial hosts, or other desirable properties.

Polypropylenes foam consisting of thermally expandable microcapsule as blowing agent

NASA Astrophysics Data System (ADS)

Jeoung, Sun Kyung; Hwang, Ye Jin; Lee, Hyun Wook; Kwak, Sung Bok; Han, In-Soo; Ha, Jin Uk

2016-03-01

The structure of thermally expandable microcapsule (TEMs) is consisted of a thermoplastic shell which is filled with liquid hydrocarbon at core. The shell of TEMs becomes soft when the temperature is higher than boiling temperature of liquid hydrocarbon. The shell of TEMs is expanded under the high temperature because the inner pressure of TEMs is increased by vaporization of hydrocarbon core. Therefore, the TEMs are applicable for blowing agents and light weight fillers. In this research, we fabricated the polypropylene (PP) foam by using the TEMs and chemical blowing agents and compared to their physical properties. The density of the specimen was decreased when the contents of chemical blowing agents and TEMs were increased. In addition, the mechanical properties (i.e. tensile strength and impact strength) of specimens were deteriorated with increasing amount of chemical blowing agents and TEMs. However, PP foam produced with TEMs showed higher impact strength than the one with the chemical blowing agent. In order to clarify the dependence of impact strength of PP foam as the blowing agent, the morphology difference of the PP foams was investigated. Expanding properties of PP foams produced with TEMs was changed with TEMs content of PP foams. Processing conditions also influenced the mechanical properties of PP foam containing TEMs.

Cuticle-degrading proteases produced by the entomopathogenic fungus Beauveria bassiana in the presence of coffee berry borer cuticle

PubMed Central

Dias, B.A.; Neves, P.M.O.J.; Furlaneto-Maia, L.; Furlaneto, M.C.

2008-01-01

A Brazilian isolate of Beauveria bassiana (CG425) that shows high virulence against the coffee berry borer (CBB) was examined for the production of subtilisin-like (Pr1) and trypsin-like (Pr2) cuticle-degrading proteases. Fungal growth was either in nitrate-medium or in CBB cuticle-containing medium under both buffered and unbuffered conditions. In unbuffered medium supplemented with cuticle, the pH of cultures dropped and Pr1 and Pr2 activities were detected in high amounts only at a pH of 5.5 or higher. In buffered cultures, Pr1 and Pr2 activities were higher in medium supplemented with cuticle compared to activities with nitrate-medium. The Pr1 and Pr2 activities detected were mostly in the culture supernatant. These data suggest that Pr1 and Pr2 proteases produced by strain CG425 are induced by components of CBB cuticle, and that the culture pH influences the expression of these proteases, indicating the occurrence of an efficient mechanism of protein secretion in this fungus. The results obtained in this study extend the knowledge about protease production in B. bassiana CG425, opening new avenues for studying the role of secreted proteases in virulence against the coffee berry borer during the infection process. PMID:24031220

Study of DT-diaphorase in pigment-producing cells.

PubMed

Smit, N P; Hoogduijn, M J; Riley, P A; Pavel, S

1999-11-01

DT-diaphorase is an FAD-containing enzyme capable of a two-electron reduction of ortho- and paraquinones. Nicotinamide coenzymes (NADH + H+ and NADPH + H+) serve as hydrogen sources in these reactions. The role of DT-diaphorase has been thoroughly investigated in situations when the enzyme is able to reduce exogenous and endogenous quinones, hence protecting the cells against these reactive intermediates. The enzyme has also been studied in connection with its ability to activate some quinoid cytostatics. It is surprising that DT-diaphorase has never been investigated in pigment-producing cells that are known to generate considerable amounts of ortho-quinones. Using a spectrophotometric method we could readily measure the activity of DT-diaphorase in epidermis and various cultured pigment cells. The melanocytes isolated from dark skin showed generally higher DT-diaphorase activity than those from fair skin samples. Also, darkly pigmented congenital naevus cells exhibited higher activity of this enzyme. The most striking was the high DT-diaphorase activity in melanoma cell cultures. In these cells DT-diaphorase activity could be induced by incubation of the cells with 4-hydroxyanisole. A similar effect was seen when a catechol-O-methyltransferase (COMT) inhibitor (3-(3,4-dihydroxy-5-nitrobenzylidene)-2,4-pentanedione (OR-462) was utilised. The induction was inhibited by cyclohexidine.

Production of tannase by the immobilized cells of Bacillus licheniformis KBR6 in Ca-alginate beads.

PubMed

Mohapatra, P K D; Mondal, K C; Pati, B R

2007-06-01

The present study was aimed at finding the optimal conditions for immobilization of Bacillus licheniformis KBR6 cells in calcium-alginate (Ca-alginate) beads and determining the operational stability during the production of tannin-acyl-hydrolase (tannase) under semicontinous cultivation. The active cells of B. licheniformis KBR6 were immobilized in Ca-alginate and used for the production of tannase. The influence of alginate concentration (5, 10, 20 and 30 g l(-1)) and initial cell loading on enzyme production were studied. The production of tannase increased significantly with increasing alginate concentration and reached a maximum enzyme yield of 0.56 +/- 0.03 U ml(-1) at 20 g l(-1). This was about 1.70-fold higher than that obtained by free cells. The immobilized cells produced tannase consistently over 13 repeated cycles and reached a maximum level at the third cycle. Scanning electron microscope study indicated that the cells in Ca-alginate beads remain in normal shape. The Ca-alginate entrapment is a promising immobilization method of B. licheniformis KBR6 for repeated tannase production. Tannase production by immobilized cells is superior to that of free cells because it leads to higher volumetric activities within the same period of fermentation. This is the first report of tannase production from immobilized bacterial cells. The bacterium under study can produce higher amounts of tannase with respect to other fungal strains within a short cultivation period.

Validation of Pooled Whole-Genome Re-Sequencing in Arabidopsis lyrata.

PubMed

Fracassetti, Marco; Griffin, Philippa C; Willi, Yvonne

2015-01-01

Sequencing pooled DNA of multiple individuals from a population instead of sequencing individuals separately has become popular due to its cost-effectiveness and simple wet-lab protocol, although some criticism of this approach remains. Here we validated a protocol for pooled whole-genome re-sequencing (Pool-seq) of Arabidopsis lyrata libraries prepared with low amounts of DNA (1.6 ng per individual). The validation was based on comparing single nucleotide polymorphism (SNP) frequencies obtained by pooling with those obtained by individual-based Genotyping By Sequencing (GBS). Furthermore, we investigated the effect of sample number, sequencing depth per individual and variant caller on population SNP frequency estimates. For Pool-seq data, we compared frequency estimates from two SNP callers, VarScan and Snape; the former employs a frequentist SNP calling approach while the latter uses a Bayesian approach. Results revealed concordance correlation coefficients well above 0.8, confirming that Pool-seq is a valid method for acquiring population-level SNP frequency data. Higher accuracy was achieved by pooling more samples (25 compared to 14) and working with higher sequencing depth (4.1× per individual compared to 1.4× per individual), which increased the concordance correlation coefficient to 0.955. The Bayesian-based SNP caller produced somewhat higher concordance correlation coefficients, particularly at low sequencing depth. We recommend pooling at least 25 individuals combined with sequencing at a depth of 100× to produce satisfactory frequency estimates for common SNPs (minor allele frequency above 0.05).

Construction of ivermectin producer by domain swaps of avermectin polyketide synthase in Streptomyces avermitilis.

PubMed

Zhang, Xiaolin; Chen, Zhi; Li, Meng; Wen, Ying; Song, Yuan; Li, Jilun

2006-10-01

Ivermectin, 22, 23-dihydroavermectin B1, is commercially important in human, veterinary medicine, and pesticides. It is currently synthesized by chemical reduction of the double bond between C22 and C23 of avermectins B1, which are a mixture of B1a (>80%) and B1b (<20%) produced by fermentation of Streptomyces avermitilis. The cost of ivermectin is much higher than that of avermectins B1 owing to the necessity of region-specific hydrogenation at C22-C23 of avermectins B1 with rhodium chloride as the catalyst for producing ivermectin. Here we report that ivermectin can be produced directly by fermentation of recombinant strains constructed through targeted genetic engineering of the avermectin polyketide synthase (PKS) in S. avermitilis Olm73-12, which produces only avermectins B and not avermectins A and oligomycin. The DNA region encoding the dehydratase (DH) and ketoreductase (KR) domains of module 2 from the avermectin PKS in S. avermitilis Olm73-12 was replaced by the DNA fragment encoding the DH, enoylreductase, and KR domains from module 4 of the pikromycin PKS of Streptomyces venezuelae ATCC 15439 using a gene replacement vector pXL211. Twenty-seven of mutants were found to produce a small amount of 22, 23-dihydroavermectin B1a and avermectin B1a and B2a by high performance liquid chromatography and liquid chromatography mass spectrometry analysis. This study might provide a route to the low-cost production of ivermectin by fermentation.

A new model evaluating Holocene sediment dynamics: Insights from a mixed carbonate-siliciclastic lagoon (Bora Bora, Society Islands, French Polynesia, South Pacific)

NASA Astrophysics Data System (ADS)

Isaack, Anja; Gischler, Eberhard; Hudson, J. Harold; Anselmetti, Flavio S.; Lohner, Andreas; Vogel, Hendrik; Garbode, Eva; Camoin, Gilbert F.

2016-08-01

Mixed carbonate-siliciclastic lagoons of barrier reefs provide great potential as sedimentary archives focusing on paleoenvironmental and paleoclimatic changes as well as on event deposition. Sediment sources include lagoonal carbonate production, the marginal reef and the volcanic hinterland. Mixed carbonate-siliciclastic continent-attached coastal lagoons have been intensively studied, however, their isolated oceanic counterparts have been widely disregarded. Here, we present a new model of Holocene sediment dynamics in the barrier-reef lagoon of Bora Bora based on sedimentological, paleontological, geochronological and geochemical data. The lagoonal succession started with a Pleistocene soil representing the Lowstand Systems Tract. As the rising Holocene sea inundated the carbonate platform, peat accumulated locally 10,650-9400 years BP. Mixed carbonate-siliciclastic sedimentation started ca. 8700-5500 years BP and represents the Transgressive Systems Tract. During that time, sediments were characterized by relatively coarse grain size and contained high amounts of terrestrial material from the volcanic hinterland as well as carbonate sediments mainly produced within the lagoon. Siliciclastic content decreases throughout the Holocene. After the rising sea had reached its modern level, sand aprons formed between reef crest and lagoon creating transport pathways for reef-derived material leading to carbonate-dominated sedimentation ca. 6000-3000 years BP during the Highstand Systems Tract. However, mainly fine material was transported and accumulated in the lagoon while coarser grains were retained on the prograding sand apron. From ca. 4500-500 years BP, significant variations in grain-size, total organic carbon as indicator for primary productivity, Ca and Cl element intensities as qualitative indicators for carbonate availability and lagoonal salinity are seen. Such patterns could indicate event (re-)deposition and correlate with contemporaneous event deposits found in the lagoon of nearby Tahaa, which are supposed to be induced by elevated cyclone activity. Correspondingly, enhanced erosion and run-off from the volcanic hinterland as well as lower lagoonal salinity would be associated with intense rainfall during repeated cyclone landfall. Increased amounts of coarse-grained sediment from marginal reef areas would be transported into the lagoon. However, Ti/Ca and Fe/Ca ratios as proxies for terrigenous sediment delivery have incessantly declined since the mid-Holocene. Also, benthic foraminiferal faunas do not validate reef-to-lagoon transport of sediment. Alternatively, the apparent onset of higher hydrodynamic energy conditions can be explained by more permanent southeast trade winds and higher-than-present sea level, which are supposed for the mid-late Holocene in the south Pacific. Sustained winds would have flushed higher amounts of open ocean water into the lagoon enhancing primary productivity and the amount of pelagic organisms within the lagoon while lowering lagoonal salinity. We propose the shift towards coarser-grained sedimentation patterns during the mid-late Holocene to reflect sediment-load shedding of sand aprons due to oversteepening of slopes at sand apron/lagoon edges during times of stronger trades and higher-than-present sea level of the Highstand Systems Tract, which led to redeposition of sediment even within the lagoon center. Modern conditions including a sea-level fall to modern level were reached ca. 1000 years BP, and lagoonal infill has been determined to a large part by fine-grained carbonate-dominated sediments produced within the lagoon and derived from the marignal reef. Infill of lagoonal accommodation space via sand aprons is estimated to be up to six times higher than infill by lagoonal background sedimentation and emphasizes the importance of the progradation of sand aprons. Contrary to the commonly supposed assumption that coarse-grained sediment layers within fine-grained lagoonal successions represent overwash events induced by storms or periods of higher storm activity, we postulate a new model of long-term lagoonal sediment dynamics including sea level, climatic change and geomorphological variation of the barrier reef lagoon.