Regulatory/Scientific Supports for Micro-, Small-, and Medium-Sized Enterprises (SMEs) With Medicinal Products Provided by the PMDA and EMA.

PubMed

Kondo, Hideyuki; Shibatsuji, Masayoshi; Yasuda, Naoyuki

2018-01-01

Micro-, small-, and medium-sized enterprises (SMEs) have been considered as key players who can bring innovative medicinal products and/or technologies into the field. However, they may need much regulatory/scientific supports to provide their products, technologies, or services to the market in a timely way. Both the Pharmaceuticals and Medical Devices Agency (PMDA) and the European Medicines Agency (EMA), regulatory authorities for medicinal products in Japan and the EU, respectively, have prepared supportive measures for SMEs from the early phase of product/technology development to the postmarketing phase. With respect to supports for SMEs, both agencies have provided similar SME-specific supportive activities, including routine administrative assistance, consultations about product development strategy from an early phase, as well as specific regulatory/scientific issues and fee incentives. In addition, there is a system to register SME status in the EU, which can be a tool for regulators to know how much potential SME-driven activities have and with whom they should communicate to provide necessary supports. Furthermore, as new technologies and novel products from SMEs are not limited to the region where they are developed, close communication about these topics between the PMDA and the EMA will contribute to advancing patients' access to necessary medicinal products.

SOLID PHASE MICROEXTRACTION FOR TRACE LEVEL ANALYSIS OF DISINFECTION BY-PRODUCTS

EPA Science Inventory

This presentation focuses on the development of a solid-phase microextraction (SPME)-gas chromatography (GC)/ion trap mass spectrometry (MS) method for the analysis of semivolatile disinfection by-products (DBPs) in drinking water in the low ug/L range. These DBPs were selected ...

SEPARATION AND QUANTITATION OF NITROBENZENES AND THEIR REDUCTION PRODUCTS NITROANILINES AND PHENYLENEDIAMINES BY REVERSED=PHASE HIGH-PERFORMANCE LIQUID CHROMATOGRAPHY

EPA Science Inventory

A reversed-phase high-performance liquid chromatographic method for the separation and quantitation of a mixture consisting of nitrobenzene, dinitrobenzene isomers, 1,3,5-trinitrobenzene and their reduction products: aniline, nitroanilines and phenylenediamines has been developed...

BG 12: BG 00012, BG 12/Oral Fumarate, FAG-201, second-generation fumarate derivative--Fumapharm/Biogen Idec.

PubMed

2005-01-01

Fumapharm AG has developed a second-generation fumarate (fumaric acid) derivative, BG 12 [BG 00012, FAG-201, BG 12/Oral Fumarate], for the oral treatment of psoriasis. Biogen Idec is currently evaluating the product in clinical trials as an oral treatment for multiple sclerosis (phase II) and psoriasis (phase III) trials.BG 12 has an immunomodulatory mechanism of action. It seems that this product has been developed to reduce the adverse effects associated with a first-generation product containing fumaric acid esters (mixed dimethylfumarate and monoethylfumarate salts), Fumaderm. Fumaderm was approved in Germany in August 1994 and is currently the leading oral systemic therapy for moderate-to-severe psoriasis in Germany. One of the problems associated with Fumaderm capsules has been its gastrointestinal adverse effects (including diarrhoea and nausea). In September 2003, Biogen (now Biogen Idec) licensed exclusive worldwide rights (excluding Germany) from Fumapharm to develop and market BG 12. Biogen plans to collaborate with Fumapharm to accelerate phase III development for psoriasis and the registration programme worldwide. Financial terms of the agreement were not disclosed. Development plans for BG 12 include other autoimmune and inflammatory disorders, such as multiple sclerosis. In November 2003, Biogen and IDEC Pharmaceuticals merged to form Biogen Idec. Fumapharm completed phase II trials of this second-generation fumarate derivative for psoriasis prior to licensing of the product to Biogen, also with positive results.

Integrating habits and practices data for soaps, cosmetics and air care products into an existing aggregate exposure model.

PubMed

Comiskey, D; Api, A M; Barrett, C; Ellis, G; McNamara, C; O'Mahony, C; Robison, S H; Rose, J; Safford, B; Smith, B; Tozer, S

2017-08-01

In order to accurately assess aggregate exposure to a fragrance material in consumers, data are needed on consumer habits and practices, as well as the concentration of the fragrance material in those products. The present study describes the development of Phase 2 Creme RIFM model by expanding the previously developed Phase 1 model to include an additional six product types. Using subject-matching algorithms, the subjects in the Phase 1 Creme RIFM database were paired with subjects in the SUPERB and BodyCare surveys based on age and gender. Consumption of the additional products was simulated to create a seven day diary allowing full data integration in a consistent format. The inhalation route was also included for air care and other products where a fraction of product used is inhaled, derived from the RIFM 2-box model. The expansion of the Phase 1 Creme RIFM model has resulted in a more extensive and refined model, which covers a broader range of product categories and now, includes all relevant routes of exposure. An evaluation of the performance of the model has been carried out in an accompanying publication to this one. Copyright © 2017 Elsevier Inc. All rights reserved.

Preliminary Development of Real Time Usage-Phase Monitoring System for CNC Machine Tools with a Case Study on CNC Machine VMC 250

NASA Astrophysics Data System (ADS)

Budi Harja, Herman; Prakosa, Tri; Raharno, Sri; Yuwana Martawirya, Yatna; Nurhadi, Indra; Setyo Nogroho, Alamsyah

2018-03-01

The production characteristic of job-shop industry at which products have wide variety but small amounts causes every machine tool will be shared to conduct production process with dynamic load. Its dynamic condition operation directly affects machine tools component reliability. Hence, determination of maintenance schedule for every component should be calculated based on actual usage of machine tools component. This paper describes study on development of monitoring system to obtaining information about each CNC machine tool component usage in real time approached by component grouping based on its operation phase. A special device has been developed for monitoring machine tool component usage by utilizing usage phase activity data taken from certain electronics components within CNC machine. The components are adaptor, servo driver and spindle driver, as well as some additional components such as microcontroller and relays. The obtained data are utilized for detecting machine utilization phases such as power on state, machine ready state or spindle running state. Experimental result have shown that the developed CNC machine tool monitoring system is capable of obtaining phase information of machine tool usage as well as its duration and displays the information at the user interface application.

Comparing the environmental footprints of home-care and personal-hygiene products: the relevance of different life-cycle phases.

PubMed

Koehler, Annette; Wildbolz, Caroline

2009-11-15

An in-depth life-cycle assessment of nine home-care and personal-hygiene products was conducted to determine the ecological relevance of different life-cycle phases and compare the environmental profiles of products serving equal applications. Using detailed data from industry and consumer-behavior studies a broad range of environmental impacts were analyzed to identify the main drivers in each life-cycle stage and potentials for improving the environmental footprints. Although chemical production significantly adds to environmental burdens, substantial impacts are caused in the consumer-use phase. As such, this research provides recommendations for product development, supply chain management, product policies, and consumer use. To reduce environmental burdens products should, for instance, be produced in concentrated form, while consumers should apply correct product dosages and low water temperatures during product application.

User Experience Evaluation Methods in Product Development (UXEM'09)

NASA Astrophysics Data System (ADS)

Roto, Virpi; Väänänen-Vainio-Mattila, Kaisa; Law, Effie; Vermeeren, Arnold

High quality user experience (UX) has become a central competitive factor of product development in mature consumer markets [1]. Although the term UX originated from industry and is a widely used term also in academia, the tools for managing UX in product development are still inadequate. A prerequisite for designing delightful UX in an industrial setting is to understand both the requirements tied to the pragmatic level of functionality and interaction and the requirements pertaining to the hedonic level of personal human needs, which motivate product use [2]. Understanding these requirements helps managers set UX targets for product development. The next phase in a good user-centered design process is to iteratively design and evaluate prototypes [3]. Evaluation is critical for systematically improving UX. In many approaches to UX, evaluation basically needs to be postponed until the product is fully or at least almost fully functional. However, in an industrial setting, it is very expensive to find the UX failures only at this phase of product development. Thus, product development managers and developers have a strong need to conduct UX evaluation as early as possible, well before all the parts affecting the holistic experience are available. Different types of products require evaluation on different granularity and maturity levels of a prototype. For example, due to its multi-user characteristic, a community service or an enterprise resource planning system requires a broader scope of UX evaluation than a microwave oven or a word processor that is meant for a single user at a time. Before systematic UX evaluation can be taken into practice, practical, lightweight UX evaluation methods suitable for different types of products and different phases of product readiness are needed. A considerable amount of UX research is still about the conceptual frameworks and models for user experience [4]. Besides, applying existing usability evaluation methods (UEMs) without adaptation to evaluate UX may lead to some scoping issues. Consequently, there is a strong need to put UX evaluation from research into practice.

Clinical Development of a Cytomegalovirus DNA Vaccine: From Product Concept to Pivotal Phase 3 Trial.

PubMed

Smith, Larry R; Wloch, Mary K; Chaplin, Jennifer A; Gerber, Michele; Rolland, Alain P

2013-09-25

2013 marks a milestone year for plasmid DNA vaccine development as a first-in-class cytomegalovirus (CMV) DNA vaccine enters pivotal phase 3 testing. This vaccine consists of two plasmids expressing CMV antigens glycoprotein B (gB) and phosphoprotein 65 (pp65) formulated with a CRL1005 poloxamer and benzalkonium chloride (BAK) delivery system designed to enhance plasmid expression. The vaccine's planned initial indication under investigation is for prevention of CMV reactivation in CMV-seropositive (CMV⁺) recipients of an allogeneic hematopoietic stem cell transplant (HCT). A randomized, double-blind placebo-controlled phase 2 proof-of-concept study provided initial evidence of the safety of this product in CMV⁺ HCT recipients who underwent immune ablation conditioning regimens. This study revealed a significant reduction in viral load endpoints and increased frequencies of pp65-specific interferon-γ-producing T cells in vaccine recipients compared to placebo recipients. The results of this endpoint-defining trial provided the basis for defining the primary and secondary endpoints of a global phase 3 trial in HCT recipients. A case study is presented here describing the development history of this vaccine from product concept to initiation of the phase 3 trial.

User systems guidelines for software projects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abrahamson, L.

1986-04-01

This manual presents guidelines for software standards which were developed so that software project-development teams and management involved in approving the software could have a generalized view of all phases in the software production procedure and the steps involved in completing each phase. Guidelines are presented for six phases of software development: project definition, building a user interface, designing software, writing code, testing code, and preparing software documentation. The discussions for each phase include examples illustrating the recommended guidelines. 45 refs. (DWL)

Silicon nitride equation of state

NASA Astrophysics Data System (ADS)

Brown, Robert C.; Swaminathan, Pazhayannur K.

2017-01-01

This report presents the development of a global, multi-phase equation of state (EOS) for the ceramic silicon nitride (Si3N4).1 Structural forms include amorphous silicon nitride normally used as a thin film and three crystalline polymorphs. Crystalline phases include hexagonal α-Si3N4, hexagonal β-Si3N4, and the cubic spinel c-Si3N4. Decomposition at about 1900 °C results in a liquid silicon phase and gas phase products such as molecular nitrogen, atomic nitrogen, and atomic silicon. The silicon nitride EOS was developed using EOSPro which is a new and extended version of the PANDA II code. Both codes are valuable tools and have been used successfully for a variety of material classes. Both PANDA II and EOSPro can generate a tabular EOS that can be used in conjunction with hydrocodes. The paper describes the development efforts for the component solid phases and presents results obtained using the EOSPro phase transition model to investigate the solid-solid phase transitions in relation to the available shock data that have indicated a complex and slow time dependent phase change to the c-Si3N4 phase. Furthermore, the EOSPro mixture model is used to develop a model for the decomposition products; however, the need for a kinetic approach is suggested to combine with the single component solid models to simulate and further investigate the global phase coexistences.

Usability in product design--the importance and need for systematic assessment models in product development--Usa-Design Model (U-D) ©.

PubMed

Merino, Giselle Schmidt Alves Díaz; Teixeira, Clarissa Stefani; Schoenardie, Rodrigo Petry; Merino, Eugenio Andrés Diáz; Gontijo, Leila Amaral

2012-01-01

In product design, human factors are considered as an element of differentiation given that today's consumer demands are increasing. Safety, wellbeing, satisfaction, health, effectiveness, efficiency, and other aspects must be effectively incorporated into the product development process. This work proposes a usability assessment model that can be incorporated as an assessment tool. The methodological approach is settled in two stages. First a literature review focus specifically on usability and developing user-centred products. After this, a model of usability named Usa-Design (U-D©) is presented. Consisted of four phases: understanding the use context, pre-preliminary usability assessment (efficiency/effectiveness/satisfaction); assessment of usability principles and results, U-D© features are modular and flexible, allowing principles used in Phase 3 to be changed according to the needs and scenario of each situation. With qualitative/quantitative measurement scales of easy understanding and application, the model results are viable and applicable throughout all the product development process.

Accelerating the introduction of HTS products for a broad range of electric power and industrial applications

NASA Astrophysics Data System (ADS)

Eaton, Russell

2002-01-01

The Department of Energy (DOE), as part of its Superconductivity Program for Electric Systems, is successfully pursuing the development of electric power and industrial devices, incorporating significant high-temperature superconducting (HTS) components or subsystems, through its innovative Superconducting Partnership Initiative (SPI). The objective of the SPI is to accelerate the commercial introduction of the HTS products for a broad range of electric power and industrial applications. DOE's approach to accomplishing the SPI objective is to support cost shared projects carried out by industry led teams. DOE will fund projects to develop HTS devices that are either in (1) the research and development stage (Phase 1), (2) the pre-commercialization stage (Phase II), or (3) the commercial entry stage (Phase III). DOE's industry partners must contribute at least half a project's costs. These teams will include capabilities needed to develop the device as well as to develop the business plan for the commercial product introduction. DOE's partners consist of vertically integrated teams consisting of equipment manufacturers, HTS wire and coil suppliers, national laboratories, and end users, primarily utilities. These partners carry out the multi-year technology development efforts, consisting generally of design, construction, and testing of the HTS system. Finally, commercialization of HTS products will be discussed primarily in terms of benefits these products will have over competing products based upon conventional conductors and the critical need for affordable, practical HTS materials and conductors for these applications. .

Silicon Nitride Equation of State

NASA Astrophysics Data System (ADS)

Swaminathan, Pazhayannur; Brown, Robert

2015-06-01

This report presents the development a global, multi-phase equation of state (EOS) for the ceramic silicon nitride (Si3N4) . Structural forms include amorphous silicon nitride normally used as a thin film and three crystalline polymorphs. Crystalline phases include hexagonal α-Si3N4, hexagonalβ-Si3N4, and the cubic spinel c-Si3N4. Decomposition at about 1900 °C results in a liquid silicon phase and gas phase products such as molecular nitrogen, atomic nitrogen, and atomic silicon. The silicon nitride EOS was developed using EOSPro which is a new and extended version of the PANDA II code. Both codes are valuable tools and have been used successfully for a variety of material classes. Both PANDA II and EOSPro can generate a tabular EOS that can be used in conjunction with hydrocodes. The paper describes the development efforts for the component solid phases and presents results obtained using the EOSPro phase transition model to investigate the solid-solid phase transitions in relation to the available shock data. Furthermore, the EOSPro mixture model is used to develop a model for the decomposition products and then combined with the single component solid models to study the global phase diagram. Sponsored by the NASA Goddard Space Flight Center Living With a Star program office.

Using Radar, Lidar, and Radiometer measurements to Classify Cloud Type and Study Middle-Level Cloud Properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Zhien

2010-06-29

The project is mainly focused on the characterization of cloud macrophysical and microphysical properties, especially for mixed-phased clouds and middle level ice clouds by combining radar, lidar, and radiometer measurements available from the ACRF sites. First, an advanced mixed-phase cloud retrieval algorithm will be developed to cover all mixed-phase clouds observed at the ACRF NSA site. The algorithm will be applied to the ACRF NSA observations to generate a long-term arctic mixed-phase cloud product for model validations and arctic mixed-phase cloud processes studies. To improve the representation of arctic mixed-phase clouds in GCMs, an advanced understanding of mixed-phase cloud processesmore » is needed. By combining retrieved mixed-phase cloud microphysical properties with in situ data and large-scale meteorological data, the project aim to better understand the generations of ice crystals in supercooled water clouds, the maintenance mechanisms of the arctic mixed-phase clouds, and their connections with large-scale dynamics. The project will try to develop a new retrieval algorithm to study more complex mixed-phase clouds observed at the ACRF SGP site. Compared with optically thin ice clouds, optically thick middle level ice clouds are less studied because of limited available tools. The project will develop a new two wavelength radar technique for optically thick ice cloud study at SGP site by combining the MMCR with the W-band radar measurements. With this new algorithm, the SGP site will have a better capability to study all ice clouds. Another area of the proposal is to generate long-term cloud type classification product for the multiple ACRF sites. The cloud type classification product will not only facilitates the generation of the integrated cloud product by applying different retrieval algorithms to different types of clouds operationally, but will also support other research to better understand cloud properties and to validate model simulations. The ultimate goal is to improve our cloud classification algorithm into a VAP.« less

Municipal solid waste development phases: Evidence from EU27.

PubMed

Vujić, Goran; Gonzalez-Roof, Alvaro; Stanisavljević, Nemanja; Ragossnig, Arne M

2015-12-01

Many countries in the European Union (EU) have very developed waste management systems. Some of its members have managed to reduce their landfilled waste to values close to zero during the last decade. Thus, European Union legislation is very stringent regarding waste management for their members and candidate countries, too. This raises the following questions: Is it possible for developing and developed countries to comply with the European Union waste legislation, and under what conditions? How did waste management develop in relation to the economic development in the countries of the European Union? The correlation between waste management practices and economic development was analysed for 27 of the European Union Member States for the time period between 1995 and 2007. In addition, a regression analysis was performed to estimate landfilling of waste in relation to gross domestic product for every country. The results showed a strong correlation between the waste management variables and the gross domestic product of the EU27 members. The definition of the municipal solid waste management development phases followed a closer analysis of the relation between gross domestic product and landfilled waste. The municipal solid waste management phases are characterised by high landfilling rates at low gross domestic product levels, and landfilling rates near zero at high gross domestic product levels. Hence the results emphasize the importance of wider understanding of what is required for developing countries to comply with the European Union initiatives, and highlight the importance of allowing developing countries to make their own paths of waste management development. © The Author(s) 2015.

Developing high-quality educational software.

PubMed

Johnson, Lynn A; Schleyer, Titus K L

2003-11-01

The development of effective educational software requires a systematic process executed by a skilled development team. This article describes the core skills required of the development team members for the six phases of successful educational software development. During analysis, the foundation of product development is laid including defining the audience and program goals, determining hardware and software constraints, identifying content resources, and developing management tools. The design phase creates the specifications that describe the user interface, the sequence of events, and the details of the content to be displayed. During development, the pieces of the educational program are assembled. Graphics and other media are created, video and audio scripts written and recorded, the program code created, and support documentation produced. Extensive testing by the development team (alpha testing) and with students (beta testing) is conducted. Carefully planned implementation is most likely to result in a flawless delivery of the educational software and maintenance ensures up-to-date content and software. Due to the importance of the sixth phase, evaluation, we have written a companion article on it that follows this one. The development of a CD-ROM product is described including the development team, a detailed description of the development phases, and the lessons learned from the project.

Microstructural Developments Leading to New Advanced High Strength Sheet Steels: A Historical Assessment of Critical Metallographic Observations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matlock, David K; Thomas, Larrin S; Taylor, Mark D

In the past 30+ years significant advancements have been made in the development of higher strength sheet steels with improved combinations of strength and ductility that have enabled important product improvements leading to safer, lighter weight, and more fuel efficient automobiles and in other applications. Properties of the primarily low carbon, low alloy steels are derived through careful control of time-temperature processing histories designed to produce multiphase ferritic based microstructures that include martensite and other constituents including retained austenite. The basis for these developments stems from the early work on dual-phase steels which was the subject of much interest. Inmore » response to industry needs, dual-phase steels have evolved as a unique class of advanced high strength sheet steels (AHSS) in which the thermal and mechanical processing histories have been specifically designed to produce constituent combinations for the purpose of simultaneously controlling strength and deformation behavior, i.e. stress-strain curve shapes. Improvements continue as enhanced dual-phase steels have recently been produced with finer microstructures, higher strengths, and better overall formability. Today, dual phase steels are the primary AHSS products used in vehicle manufacture, and several companies have indicated that the steels will remain as important design materials well into the future. In this presentation, fundamental results from the early work on dual-phase steels will be reviewed and assessed in light of recent steel developments. Specific contributions from industry/university cooperative research leading to product improvements will be highlighted. The historical perspective provided in the evolution of dual-phase steels represents a case-study that provides important framework and lessons to be incorporated in next generation AHSS products.« less

FuzzyCLIPS from research to product

NASA Technical Reports Server (NTRS)

Bochsler, Dan; Dohmann, Edgar

1994-01-01

This paper describes the commercial productization of FuzzyCLIPS which was developed under a NASA Phase 2 SBIR contract. The intent of this paper is to provide a general roadmap of the processes that are required to make a viable, marketable product once its concept and development are complete.

Optimization of Deep Drilling Performance--Development and Benchmark Testing of Advanced Diamond Product Drill Bits & HP/HT Fluids to Significantly Improve Rates of Penetration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alan Black; Arnis Judzis

2003-10-01

This document details the progress to date on the OPTIMIZATION OF DEEP DRILLING PERFORMANCE--DEVELOPMENT AND BENCHMARK TESTING OF ADVANCED DIAMOND PRODUCT DRILL BITS AND HP/HT FLUIDS TO SIGNIFICANTLY IMPROVE RATES OF PENETRATION contract for the year starting October 2002 through September 2002. The industry cost shared program aims to benchmark drilling rates of penetration in selected simulated deep formations and to significantly improve ROP through a team development of aggressive diamond product drill bit--fluid system technologies. Overall the objectives are as follows: Phase 1--Benchmark ''best in class'' diamond and other product drilling bits and fluids and develop concepts for amore » next level of deep drilling performance; Phase 2--Develop advanced smart bit--fluid prototypes and test at large scale; and Phase 3--Field trial smart bit--fluid concepts, modify as necessary and commercialize products. Accomplishments to date include the following: 4Q 2002--Project started; Industry Team was assembled; Kick-off meeting was held at DOE Morgantown; 1Q 2003--Engineering meeting was held at Hughes Christensen, The Woodlands Texas to prepare preliminary plans for development and testing and review equipment needs; Operators started sending information regarding their needs for deep drilling challenges and priorities for large-scale testing experimental matrix; Aramco joined the Industry Team as DEA 148 objectives paralleled the DOE project; 2Q 2003--Engineering and planning for high pressure drilling at TerraTek commenced; 3Q 2003--Continuation of engineering and design work for high pressure drilling at TerraTek; Baker Hughes INTEQ drilling Fluids and Hughes Christensen commence planning for Phase 1 testing--recommendations for bits and fluids.« less

Analysis of the Lifecycle of Mechanical Engineering Products

NASA Astrophysics Data System (ADS)

Gubaydulina, R. H.; Gruby, S. V.; Davlatov, G. D.

2016-08-01

Principal phases of the lifecycle of mechanical engineering products are analyzed in the paper. The authors have developed methods and procedures to improve designing, manufacturing, operating and recycling of the machine. It has been revealed that economic lifecycle of the product is a base for appropriate organization of mechanical engineering production. This lifecycle is calculated as a minimal sum total of consumer and producer costs. The machine construction and its manufacturing technology are interrelated through a maximal possible company profit. The products are to be recycled by their producer. Recycling should be considered as a feedback phase, necessary to make the whole lifecycle of the product a constantly functioning self-organizing system. The principles, outlined in this paper can be used as fundamentals to develop an automated PLM-system.

Environmental Assessment of the Hawaii Geothermal Project Well Flow Test Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1976-11-01

The Hawaii Geothermal Project, a coordinated research effort of the University of Hawaii, funded by the County and State of Hawaii, and ERDA, was initiated in 1973 in an effort to identify, generate, and use geothermal energy on the Big Island of Hawaii. A number of stages are involved in developing geothermal power resources: exploration, test drilling, production testing, field development, power plant and powerline construction, and full-scale production. Phase I of the Project, which began in the summer of 1973, involved conducting exploratory surveys, developing analytical models for interpretation of geophysical results, conducting studies on energy recovery from hotmore » brine, and examining the legal and economic implications of developing geothermal resources in the state. Phase II of the Project, initiated in the summer of 1975, centers on drilling an exploratory research well on the Island of Hawaii, but also continues operational support for the geophysical, engineering, and socioeconomic activities delineated above. The project to date is between the test drilling and production testing phase. The purpose of this assessment is to describe the activities and potential impacts associated with extensive well flow testing to be completed during Phase II.« less

Technological change and productivity growth in the air transport industry

NASA Technical Reports Server (NTRS)

Rosenberg, N.; Thompson, A.; Belsley, S. E.

1978-01-01

The progress of the civil air transport industry in the United States was examined in the light of a proposal of Enos who, after examining the growth of the petroleum industry, divided that phenomenon into two phases, the alpha and the beta; that is, the invention, first development and production, and the improvement phase. The civil air transport industry developed along similar lines with the technological progress coming in waves; each wave encompassing several new technological advances while retaining the best of the old ones. At the same time the productivity of the transport aircraft as expressed by the product of the aircraft velocity and the passenger capacity increased sufficiently to allow the direct operating cost in cents per passenger mile to continually decrease with each successive aircraft development.

Clinical development of gene- and cell-based therapies: overview of the European landscape

PubMed Central

de Wilde, Sofieke; Guchelaar, Henk-Jan; Zandvliet, Maarten Laurens; Meij, Pauline

2016-01-01

In the last decade, many clinical trials with gene- and cell-based therapies were performed and increasing interest in the development was established by (national) authorities, academic developers, and commercial companies. However, until now only eight products have received marketing authorization (MA) approval. In this study, a comprehensive overview of the clinical development of gene- and cell-based therapies in Europe is presented, with a strong focus on product-technical aspects. Public data regarding clinical trials with gene- and cell-based therapies, obtained from the European Union (EU) clinical trial database (EudraCT) between 2004 and 2014 were analyzed, including product-technical variables as potential determinants affecting development. 198 unique gene and cell therapy products were identified, which were studied in 278 clinical trials, mostly in phase 1/2 trials and with cell therapies as major group. Furthermore, most products were manufactured from autologous starting material mostly manufactured from stem cells. The majority of the trials were sponsored by academia, whereas phase 3 trials mostly by large companies. Academia dominated early-stage development by mainly using bone marrow derived products and stem cells. Conversely, commercial sponsors were more actively pursuing in vivo gene therapy medicinal product development, and cell therapies derived from differentiated tissue in later-stage development. PMID:27990447

Experimental measurement of oil-water two-phase flow by data fusion of electrical tomography sensors and venturi tube

NASA Astrophysics Data System (ADS)

Liu, Yinyan; Deng, Yuchi; Zhang, Maomao; Yu, Peining; Li, Yi

2017-09-01

Oil-water two-phase flows are commonly found in the production processes of the petroleum industry. Accurate online measurement of flow rates is crucial to ensure the safety and efficiency of oil exploration and production. A research team from Tsinghua University has developed an experimental apparatus for multiphase flow measurement based on an electrical capacitance tomography (ECT) sensor, an electrical resistance tomography (ERT) sensor, and a venturi tube. This work presents the phase fraction and flow rate measurements of oil-water two-phase flows based on the developed apparatus. Full-range phase fraction can be obtained by the combination of the ECT sensor and the ERT sensor. By data fusion of differential pressures measured by venturi tube and the phase fraction, the total flow rate and single-phase flow rate can be calculated. Dynamic experiments were conducted on the multiphase flow loop in horizontal and vertical pipelines and at various flow rates.

Comprehensive Analysis of the Gas- and Particle-Phase Products of VOC Oxidation

NASA Astrophysics Data System (ADS)

Bakker-Arkema, J.; Ziemann, P. J.

2017-12-01

Controlled environmental chamber studies are important for determining atmospheric reaction mechanisms and gas and aerosol products formed in the oxidation of volatile organic compounds (VOCs). Such information is necessary for developing detailed chemical models for use in predicting the atmospheric fate of VOCs and also secondary organic aerosol (SOA) formation. However, complete characterization of atmospheric oxidation reactions, including gas- and particle-phase product yields, and reaction branching ratios, are difficult to achieve. In this work, we investigated the reactions of terminal and internal alkenes with OH radicals in the presence of NOx in an attempt to fully characterize the chemistry of these systems while minimizing and accounting for the inherent uncertainties associated with environmental chamber experiments. Gas-phase products (aldehydes formed by alkoxy radical decomposition) and particle-phase products (alkyl nitrates, β-hydroxynitrates, dihydroxynitrates, 1,4-hydroxynitrates, 1,4-hydroxycarbonyls, and dihydroxycarbonyls) formed through pathways involving addition of OH to the C=C double bond as well as H-atom abstraction were identified and quantified using a suite of analytical techniques. Particle-phase products were analyzed in real time with a thermal desorption particle beam mass spectrometer; and off-line by collection onto filters, extraction, and subsequent analysis of functional groups by derivatization-spectrophotometric methods developed in our lab. Derivatized products were also separated by liquid chromatography for molecular quantitation by UV absorbance and identification using chemical ionization-ion trap mass spectrometry. Gas phase aldehydes were analyzed off-line by collection onto Tenax and a 5-channel denuder with subsequent analysis by gas chromatography, or by collection onto DNPH-coated cartridges and subsequent analysis by liquid chromatography. The full product identification and quantitation, with careful minimization of uncertainties for the various components of the experiment and analyses, demonstrates our capability to comprehensively and accurately analyze the complex chemical composition of products formed in the oxidation of organic compounds in laboratory chamber studies.

Framework for the Development of OER-Based Learning Materials in ODL Environment

ERIC Educational Resources Information Center

Teng, Khor Ean; Hung, Chung Sheng

2013-01-01

This paper describes the framework for the development of OER-based learning materials "TCC121/05 Programming Fundamentals with Java" for ODL learners in Wawasan Open University (WOU) using three main development phases mainly: creation, evaluation and production phases. The proposed framework has further been tested on ODL learners to…

Technology development for iron Fischer-Tropsch catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

O`Brien, R.J.; Raje, A.; Keogh, R.A.

1995-12-31

The objective of this research project is to develop the technology for the production of physically robust iron-based Fischer-Tropsch catalysts that have suitable activity, selectivity and stability to be used in the slurry phase synthesis reactor development. The catalysts that are developed shall be suitable for testing in the Advanced Fuels Development Facility at LaPorte, Texas, to produce either low-or high-alpha product distributions. Previous work by the offeror has produced a catalyst formulation that is 1.5 times as active as the {open_quotes}standard-catalyst{close_quotes} developed by German workers for slurry phase synthesis. In parallel, work will be conducted to design a high-alphamore » iron catalyst this is suitable for slurry phase synthesis. Studies will be conducted to define the chemical phases present at various stages of the pretreatment and synthesis stages and to define the course of these changes. The oxidation/reduction cycles that are anticipated to occur in large, commercial reactors will be studied at the laboratory scale. Catalyst performance will be determined for catalysts synthesized in this program for activity, selectivity and aging characteristics.« less

Prevention of MSD by means of ergonomic risk assessment (tools) in all phases of the vehicle development process.

PubMed

Karlheinz, Schaub; Michaela, Kugler; Max, Bierwirth; Andrea, Sinn-Behrendt; Ralph, Bruder

2012-01-01

In industrialized countries musculoskeletal disorders (MSD) play an import role and are often responsible for almost one third of the total sick leave. The changes in the demographic profiles, i.e. aging work forces might even worsen this situation in the future. For a highly productive and sustainable use of human resources in production systems, ergonomics offers high potentials. In the recent years the authors have developed several ergonomic risk assessment tools, especially for the use in automotive industries. These methods may be used during the planning phases in the Tech Centers as well as during the production phase at shop floor level. The tools might also be used for a standardized communication in between the Tech Center and the plants to improve the effects of "lessons learned" for the design and layout of workstations and processes and the optimization of vehicle components. This paper describes suitable risk assessment tools as well as the integration of these tools into the vehicle development process. It introduces a comprehensive management approach for the integration of ergonomics into the management of production systems.

Using focus groups in the consumer research phase of a social marketing program to promote moderate-intensity physical activity and walking trail use in Sumter County, South Carolina.

PubMed

Burroughs, Ericka; Peck, Lara E; Sharpe, Patricia A; Granner, Michelle L; Bryant, Carol A; Fields, Regina

2006-01-01

The use of social marketing approaches in public health practice is increasing. Using marketing concepts such as the "four Ps" (product, price, place, and promotion), social marketing borrows from the principles of commercial marketing but promotes beneficial health behaviors. Consumer research is used to segment the population and develop a strategy based on those marketing concepts. In a community-based participatory research study, 17 focus groups were used in consumer research to develop a social marketing program to promote walking and other moderate-intensity physical activities. Two phases of focus groups were conducted. Phase 1 groups, which included both men and women, were asked to respond to questions that would guide the development of a social marketing program based on social marketing concepts. Phase 1 also determined the intervention's target audience, which was irregularly active women aged 35 to 54. Phase 2 groups, composed of members of the target audience, were asked to further define the product and discuss specific promotion strategies. Phase 1 participants determined that the program product, or target behavior, should be walking. In addition, they identified price, place, and promotion strategies. Phase 2 participants determined that moderate-intensity physical activity is best promoted using the term exercise and offered suggestions for marketing walking, or exercise, to the target audience. There have been few published studies of social marketing campaigns to promote physical activity. In this study, focus groups were key to understanding the target audience in a way that would not have been accomplished with quantitative data alone. The group discussions generated important insights into values and motivations that affect consumers' decisions to adopt a product or behavior. The focus group results guided the development of a social marketing program to promote physical activity in the target audience in Sumter County, South Carolina.

A meta-heuristic approach supported by NSGA-II for the design and plan of supply chain networks considering new product development

NASA Astrophysics Data System (ADS)

Alizadeh Afrouzy, Zahra; Paydar, Mohammad Mahdi; Nasseri, Seyed Hadi; Mahdavi, Iraj

2018-03-01

There are many reasons for the growing interest in developing new product projects for any firm. The most embossed reason is surviving in a highly competitive industry which the customer tastes are changing rapidly. A well-managed supply chain network can provide the most profit for firms due to considering new product development. Along with profit, customer satisfaction and production of new products are goals which lead to a more efficient supply chain. As new products appear in the market, the old products could become obsolete, and then phased out. The most important parameter in a supply chain which considers new and developed products is the time that developed and new products are introduced and old products are phased out. With consideration of the factors noted above, this study proposes to design a tri-objective multi-echelon multi-product multi-period supply chain model, which incorporates product development and new product production and their effects on supply chain configuration. The supply chain under consideration is assumed to consist of suppliers, manufacturers, distributors and customer groups. In terms of overcoming NP-hardness of the proposed model and in order to solve the complicated problem, a non-dominated sorting genetic algorithm is employed. As there is no benchmark available in the literature, the non-dominated ranking genetic algorithm is developed to validate the results obtained and some test problems are provided to show the applicability of the proposed methodology and evaluate the performance of the algorithms.

A compositional multiphase model for groundwater contamination by petroleum products: 1. Theoretical considerations

USGS Publications Warehouse

Corapcioglu, M. Yavuz; Baehr, Arthur L.

1987-01-01

A mathematical model is developed to describe the fate of hydrocarbon constituents of petroleum products introduced to soils as an immiscible liquid from sources such as leaking underground storage tanks and ruptured pipelines. The problem is one of multiphase transport (oil (immiscible), air, and water phases) of a reactive contaminant with constituents such as benzene, toluene, and xylene found in refined petroleum products like gasoline. In the unsaturated zone, transport of each constituent can occur as a solute in the water phase, vapor in the air phase, and as an unaltered constituent in the oil phase. Additionally, the model allows for adsorption. Molecular transformations, microbially mediated or abiotic, are incorporated as sink terms in the conservation of mass equations. An equilibrium approximation, applicable to any immiscible organic contaminant is applied to partition constituent mass between the air, oil, water, and adsorbed phases for points in the region where the oil phase exists. Outside the oil plume the equilibrium approximation takes on a simpler form to partition constituent mass between the air, water, and adsorbed phases only. Microbial degradation of petroleum products is first discussed in a general model, then the conservation of mass equation for oxygen is incorporated into the analysis which takes advantage of the key role played by oxygen in the metabolism of hydrocarbon utilizing microbes in soil environments. Approximations to two subproblems, oil plume establishment in the unsaturated zone, and solute and vapor transport subsequent to immiscible plume establishment are then developed from the general model.

Using Android-Based Educational Game for Learning Colloid Material

NASA Astrophysics Data System (ADS)

Sari, S.; Anjani, R.; Farida, I.; Ramdhani, M. A.

2017-09-01

This research is based on the importance of the development of student’s chemical literacy on Colloid material using Android-based educational game media. Educational game products are developed through research and development design. In the analysis phase, material analysis is performed to generate concept maps, determine chemical literacy indicators, game strategies and set game paths. In the design phase, product packaging is carried out, then validation and feasibility test are performed. Research produces educational game based on Android that has the characteristics that is: Colloid material presented in 12 levels of game in the form of questions and challenges, presents visualization of discourse, images and animation contextually to develop the process of thinking and attitude. Based on the analysis of validation and trial results, the product is considered feasible to use.

Developmental Changes in Early Comprehension and Production of Drawings: Evidence From Two Socioeconomic Backgrounds.

PubMed

Salsa, Analía M; Vivaldi, Romina

2017-01-01

Two studies examined young children's comprehension and production of representational drawings across and within 2 socioeconomic strata (SES). Participants were 130 middle-SES (MSES) and low-SES (LSES) Argentine children, from 30 to 60 months old, given a task with 2 phases, production and comprehension. The production phase assessed free drawing and drawings from simple 3-dimensional objects (model drawing); the comprehension phase assessed children's understanding of an adult's line drawings of the objects. MSES children solved the comprehension phase of the task within the studied age range; representational production emerged first in model drawing (42 months) and later in free drawing (48 months). The same developmental pathway was observed in LSES children but with a clear asynchrony in the age of onset of comprehension and production: Children understood the symbolic nature of drawings at 42 months old and the first representational drawings were found at 60 months old. These results provide empirical evidence that support the crucial influence of social experiences by organizing and constraining graphic development.

3D printing technology speeds development.

PubMed

McGowan, James

2013-10-01

James McGowan, R&D product designer for Monodraught, a specialist in 'natural ventilation, natural daylight, and natural cooling systems', discusses the development of Cool-phase, the company's latest innovative application of phase change material (PCM) as a thermal energy store used to actively ventilate and cool buildings. As he explains, when the company decided to re-design an already successful product to further enhance its performance, the use of 3D modelling greatly speeded up prototyping, and helped the design process progress considerably more quickly.

Developing a Point-of-Sale Health Communication Campaign for Cigarillos and Waterpipe Tobacco.

PubMed

Sutfin, Erin L; Cornacchione Ross, Jennifer; Lazard, Allison J; Orlan, Elizabeth; Suerken, Cynthia K; Wiseman, Kimberly D; Reboussin, Beth A; Wolfson, Mark; Noar, Seth M

2017-12-13

Adolescents and young adults smoke waterpipe tobacco (WT) and cigarillos, at least in part, based on erroneous beliefs that these products are safer than cigarettes. To address this challenge, we used a systematic, three-phase process to develop a health communication campaign to discourage WT and cigarillo smoking among at-risk (tobacco users and susceptible non-users) 16- to 25-year-olds. In Phase 1, we used a national phone survey (N = 896) to determine salient message beliefs. Participants reported constituents (i.e., harmful chemicals) emitted by the products were worrisome. In Phase 2, we developed and evaluated four message executions, with varying imagery, tone, and unappealing products with the same constituents, using focus groups (N = 38). Participants rated one execution highly, resulting in our development of a campaign where each message: (1) identified a tobacco product and constituent in the smoke; (2) included an image of an unappealing product containing the constituent (e.g., pesticides, gasoline) to grab attention; and (3) used a humorous sarcastic tone. In Phase 3, we tested the campaign messages (17 intervention and six control) with a nationally representative online survey (N = 1,636). Participants rated intervention and control messages highly with few differences between them. Exposure to messages resulted in significant increases in all risk beliefs from pre to post (p < 0.05). For WT, intervention messages increased beliefs about addiction more than control messages (p < 0.05). This systematic, iterative approach resulted in messages that show promise for discouraging WT and cigarillo use.

Effects of Surotomycin on Clostridium difficile Viability and Toxin Production In Vitro

PubMed Central

Bouillaut, Laurent; McBride, Shonna; Schmidt, Diane J.; Suarez, José M.; Tzipori, Saul; Mascio, Carmela; Chesnel, Laurent

2015-01-01

The increasing incidence and severity of infection by Clostridium difficile have stimulated attempts to develop new antimicrobial therapies. We report here the relative abilities of two antibiotics (metronidazole and vancomycin) in current use for treating C. difficile infection and of a third antimicrobial, surotomycin, to kill C. difficile cells at various stages of development and to inhibit the production of the toxin proteins that are the major virulence factors. The results indicate that none of the drugs affects the viability of spores at 8× MIC or 80× MIC and that all of the drugs kill exponential-phase cells when provided at 8× MIC. In contrast, none of the drugs killed stationary-phase cells or inhibited toxin production when provided at 8× MIC and neither vancomycin nor metronidazole killed stationary-phase cells when provided at 80× MIC. Surotomycin, on the other hand, did kill stationary-phase cells when provided at 80× MIC but did so without inducing lysis. PMID:25941230

FDA perspective on specifications for biotechnology products--from IND to PLA.

PubMed

Murano, G

1997-01-01

Quality standards are obligatory throughout development, approval and post-marketing phases of biotechnology-derived products, thus assuring product identity, purity, and potency/strength. The process of developing and setting specifications should be based on sound science and should represent a logical progression of actions based on the use of experiential data spanning manufacturing process validation, consistency in production, and characterization of relevant product properties/attributes, by multiple analytical means. This interactive process occurs in phases, varying in rigour. It is best described as encompassing a framework which starts with the implementation of realistic/practical operational quality limits, progressing to the establishment/adoption of more stringent specifications. The historical database is generated from preclinical, toxicology and early clinical lots. This supports the clinical development programme which, as it progresses, allows for further assay method validation/refinement, adoption/addition due to relevant or newly recognized product attributes or rejection due to irrelevance. In the next phase, (licensing/approval) specifications are set through extended experience and validation of both the preparative and analytical processes, to include availability of suitable reference standards and extensive product characterization throughout its proposed dating period. Subsequent to product approval, the incremental database of test results serves as a natural continuum for further evolving/refining specifications. While there is considerable latitude in the kinds of testing modalities finally adopted to establish product quality on a routine basis, for both drugs and drug products, it is important that the selection takes into consideration relevant (significant) product characteristics that appropriately reflect on identity, purity and potency.

Preliminary experience of a PDCA-cycle and quality management based training curriculum for rat liver transplantation.

PubMed

Jin, Hao; Huang, Hai; Dong, Wei; Sun, Jian; Liu, Anding; Deng, Meihong; Dirsch, Olaf; Dahmen, Uta

2012-08-01

As repeatedly operating rat liver transplantation (LTx) until animals survive is inefficient in respect to time and use of living animals, we developed a new training concept. METHODS AND CONCEPTS: Training was divided into four phases: pretraining-phase, basic-microsurgical-training phase, advanced-microsurgical-training phases, and expert-microsurgical-training phase. Two "productivity-phases" were introduced right after the basic- and advanced-microsurgical-training phases, respectively, to allow the trainee to accumulate experience and to be scientifically productive before proceeding to a more complex procedure. PDCA cycles and quality criteria were employed to control the learning-process and the surgical quality. Predefined quality criteria included survival rate, intraoperative, postoperative, and histologic parameters. Three trainees participated in the LTx training and achieved their first survival record within 4-10 operations. All of them completely mastered the LTx in fewer procedures (31, 60 and 26 procedures) as reported elsewhere, and the more complex arterialized or partial LTx were mastered by trainee A and B in additional 9 and 13 procedures, respectively. Fast progress was possible due to a high number of training in the 2 Productivity-phases. The stepwise and PDCA-based training program increased the efficiency of LTx training, whereas the constant application and development of predefined quality criteria guaranteed the quality of microsurgery. Copyright © 2012 Elsevier Inc. All rights reserved.

Developments toward large-scale bacterial bioprocesses in the presence of bulk amounts of organic solvents.

PubMed

Schmid, A; Kollmer, A; Mathys, R G; Witholt, B

1998-08-01

Many pseudomonads and other bacteria can grow on aliphatic and aromatic hydrocarbons that occur in the environment. We are examining the potential of such organisms as biocatalysts for the oxidation of a variety of substituted aliphatic and aromatic compounds. To attain a high production rate of oxidation products via such biotransformations, we have focused on two-liquid phase culture systems. In these systems, cells are grown in liquid media consisting of an aqueous phase containing water-soluble growth substrates and droplets of a water-immicible organic solvent containing bioconversion substrates and products. For industrial applications of such two-liquid phase processes, several questions remain. What are the maximum rates at which apolar compounds can be transferred from the apolar phase to cells growing in the aqueous phase, i.e., what are the maximum space-time yields attainable in two-liquid phase fermentations under practical conditions? What does an efficient downstream processing of two-liquid phase medium involve? What safety regimes should be considered in working with flammable organic solvents? Can elevated pressure be used to increase oxygen transfer? Based on answers to these questions, we have recently developed a high-pressure, explosion-proof bioreactor system with Bioengineering AG (Wald, Switzerland), which will be installed in our pilot plant and used to explore two-liquid phase bioconversions at a pilot scale.

Development of a model and computer code to describe solar grade silicon production processes

NASA Technical Reports Server (NTRS)

Srivastava, R.; Gould, R. K.

1979-01-01

Mathematical models, and computer codes based on these models were developed which allow prediction of the product distribution in chemical reactors in which gaseous silicon compounds are converted to condensed phase silicon. The reactors to be modeled are flow reactors in which silane or one of the halogenated silanes is thermally decomposed or reacted with an alkali metal, H2 or H atoms. Because the product of interest is particulate silicon, processes which must be modeled, in addition to mixing and reaction of gas-phase reactants, include the nucleation and growth of condensed Si via coagulation, condensation, and heterogeneous reaction.

Risk management in medical product development process using traditional FMEA and fuzzy linguistic approach: a case study

NASA Astrophysics Data System (ADS)

Kirkire, Milind Shrikant; Rane, Santosh B.; Jadhav, Jagdish Rajaram

2015-12-01

Medical product development (MPD) process is highly multidisciplinary in nature, which increases the complexity and the associated risks. Managing the risks during MPD process is very crucial. The objective of this research is to explore risks during MPD in a dental product manufacturing company and propose a model for risk mitigation during MPD process to minimize failure events. A case study approach is employed. The existing MPD process is mapped with five phases of the customized phase gate process. The activities during each phase of development and risks associated with each activity are identified and categorized based on the source of occurrence. The risks are analyzed using traditional Failure mode and effect analysis (FMEA) and fuzzy FMEA. The results of two methods when compared show that fuzzy approach avoids the duplication of RPNs and helps more to convert cognition of experts into information to get values of risk factors. The critical, moderate, low level and negligible risks are identified based on criticality; risk treatments and mitigation model are proposed. During initial phases of MPD, the risks are less severe, but as the process progresses the severity of risks goes on increasing. The MPD process should be critically designed and simulated to minimize the number of risk events and their severity. To successfully develop the products/devices within the manufacturing companies, the process risk management is very essential. A systematic approach to manage risks during MPD process will lead to the development of medical products with expected quality and reliability. This is the first research of its kind having focus on MPD process risks and its management. The methodology adopted in this paper will help the developers, managers and researchers to have a competitive edge over the other companies by managing the risks during the development process.

Differential involvement of ipsilateral and contralateral spinal cord astrocyte D-serine in carrageenan-induced mirror-image pain: role of σ1 receptors and astrocyte gap junctions.

PubMed

Choi, Hoon-Seong; Roh, Dae-Hyun; Yoon, Seo-Yeon; Choi, Sheu-Ran; Kwon, Soon-Gu; Kang, Suk-Yun; Moon, Ji-Young; Han, Ho-Jae; Beitz, Alvin J; Lee, Jang-Hern

2018-02-01

Although we have recently demonstrated that spinal astrocyte gap junctions mediate the development of mirror-image pain (MIP), it is still unclear which astrocyte-derived factor is responsible for the development of MIP and how its production is controlled. In the present study, we focused on the role of ipsilateral versus contralateral D-serine in the development of MIP and investigated the possible involvement of σ1 receptors and gap junctions in astrocyte D-serine production. Following carrageenan injection, mechanical allodynia was tested at various time points to examine the effect of individual drugs. Immunohistochemistry and Western blot analyses were performed to clarify the expression levels of spinal D-serine, serine racemase, σ1 receptors and connexin 43. The expression of ipsilateral D-serine was up-regulated during the early phase of inflammation, while contralateral D-serine increased during the later phase of inflammation. The pharmacological inhibition of D-serine during the early phase blocked the development of both ipsilateral and contralateral mechanical allodynia. However, the inhibition of D-serine during the later phase of inflammation blocked contralateral, but not ipsilateral mechanical allodynia. Furthermore, the inhibition of σ1 receptors during the earlier phase of inflammation inhibited the increase in ipsilateral D-serine. Conversely, the blockade of astrocyte gap junctions suppressed the up-regulation of contralateral D-serine during the later phase of inflammation. Spinal astrocyte D-serine plays an important role in the development of mirror-image pain. Furthermore, σ1 receptors and astrocyte gap junction signalling mediate ipsilateral and contralateral D-serine production respectively. © 2017 The British Pharmacological Society.

Expendable Air Vehicles/High Altitude Balloon Technology. Phase 1.

DTIC Science & Technology

1991-08-02

CHR/91 -2750 I I I I I THIS PAGE INTENTIONALLY LEFT BLANK 3 I I U I I I I I I I I I CHR/91 -2750 PREFACE The work described in this Phase II SBIR...Final Technical Report is the implementation of a capability which Coleman Research Corporation demon- strated during a Phase I SBIR (contract number...CRC) has developed a Balloon Drift Pattern Simulation 1BDPS). CRC developed this simulation software for digital computers as a product of a Phase II

Development of a Solid Phase Extraction Method for Agricultural Pesticides in Large-Volume Water Samples

EPA Science Inventory

An analytical method using solid phase extraction (SPE) and analysis by gas chromatography/mass spectrometry (GC/MS) was developed for the trace determination of a variety of agricultural pesticides and selected transformation products in large-volume high-elevation lake water sa...

Resonant di-Higgs boson production in the b b ¯ W W channel: Probing the electroweak phase transition at the LHC

DOE PAGES

Huang, T.; No, J. M.; Pernié, L.; ...

2017-08-11

Here, we analyze the prospects for resonant di-Higgs production searches at the LHC in themore » $$b\\bar{b}$$W +W − (W +→ℓ +ν ℓ, W −→ℓ −$$\\bar{v}$$ ℓ) channel, as a probe of the nature of the electroweak phase transition in Higgs portal extensions of the Standard Model. In order to maximize the sensitivity in this final state, we develop a new algorithm for the reconstruction of the $$b\\bar{b}$$W +W − invariant mass in the presence of neutrinos from the W decays, building from a technique developed for the reconstruction of resonances decaying to τ +τ − pairs. We show that resonant di-Higgs production in the $$b\\bar{b}$$W +W − channel could be a competitive probe of the electroweak phase transition already with the data sets to be collected by the CMS and ATLAS experiments in run 2 of the LHC. The increase in sensitivity with larger amounts of data accumulated during the high-luminosity LHC phase can be sufficient to enable a potential discovery of the resonant di-Higgs production in this channel.« less

Resonant di-Higgs boson production in the b b ¯ W W channel: Probing the electroweak phase transition at the LHC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, T.; No, J. M.; Pernié, L.

Here, we analyze the prospects for resonant di-Higgs production searches at the LHC in themore » $$b\\bar{b}$$W +W − (W +→ℓ +ν ℓ, W −→ℓ −$$\\bar{v}$$ ℓ) channel, as a probe of the nature of the electroweak phase transition in Higgs portal extensions of the Standard Model. In order to maximize the sensitivity in this final state, we develop a new algorithm for the reconstruction of the $$b\\bar{b}$$W +W − invariant mass in the presence of neutrinos from the W decays, building from a technique developed for the reconstruction of resonances decaying to τ +τ − pairs. We show that resonant di-Higgs production in the $$b\\bar{b}$$W +W − channel could be a competitive probe of the electroweak phase transition already with the data sets to be collected by the CMS and ATLAS experiments in run 2 of the LHC. The increase in sensitivity with larger amounts of data accumulated during the high-luminosity LHC phase can be sufficient to enable a potential discovery of the resonant di-Higgs production in this channel.« less

BIOWINOL TECHNOLOGIES: A HYBRID GREEN PROCESS FOR BIOFUEL PRODUCTION – PHASE 2

EPA Science Inventory

The development of hollow fiber membrane (HFM) reactor will result in improved gas utilization that will positively impact overall process efficiencies. Successful completion of this project could result in the development of many decentralized biofuel production systems near ...

Kinetic modeling of sporulation and product formation in stationary phase by Bacillus coagulans RK-02 vis-à-vis other Bacilli.

PubMed

Das, Subhasish; Sen, Ramkrishna

2011-10-01

A logistic kinetic model was derived and validated to characterize the dynamics of a sporogenous bacterium in stationary phase with respect to sporulation and product formation. The kinetic constants as determined using this model are particularly important for describing intrinsic properties of a sporogenous bacterial culture in stationary phase. Non-linear curve fitting of the experimental data into the mathematical model showed very good correlation with the predicted values for sporulation and lipase production by Bacillus coagulans RK-02 culture in minimal media. Model fitting of literature data of sporulation and product (protease and amylase) formation in the stationary phase by some other Bacilli and comparison of the results of model fitting with those of Bacillus coagulans helped validate the significance and robustness of the developed kinetic model. Copyright © 2011 Elsevier Ltd. All rights reserved.

Development Status for the Stennis Space Center LIDAR Product Characterization Range

NASA Technical Reports Server (NTRS)

Zanoni, Vicki; Berglund, Judith; Ross, Kenton

2004-01-01

The presentation describes efforts to develop a LIDAR in-flight product characterization range at Stennis Space Center as the next phase of the NASA Verification and Validation activities. It describes the status of surveying efforts on targets of interest to LIDAR vendors as well as the potential guidelines that will be used for product characterization.

Carbon Mineralization by Aqueous Precipitation for Beneficial Use of CO2 from Flue Gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brent Constantz; Randy Seeker; Martin Devenney

2010-06-30

Calera's innovative Mineralization via Aqueous Precipitation (MAP) technology for the capture and conversion of CO{sub 2} to useful materials for use in the built environment was further developed and proven in the Phase 1 Department of Energy Grant. The process was scaled to 300 gallon batch reactors and subsequently to Pilot Plant scale for the continuous production of product with the production of reactive calcium carbonate material that was evaluated as a supplementary cementitious material (SCM). The Calera SCM{trademark} was evaluated as a 20% replacement for ordinary portland cement and demonstrated to meet the industry specification ASTM 1157 which ismore » a standard performance specification for hydraulic cement. The performance of the 20% replacement material was comparable to the 100% ordinary portland cement control in terms of compressive strength and workability as measured by a variety of ASTM standard tests. In addition to the performance metrics, detailed characterization of the Calera SCM was performed using advanced analytical techniques to better understand the material interaction with the phases of ordinary portland cement. X-ray synchrotron diffraction studies at the Advanced Photon Source in Argonne National Lab confirmed the presence of an amorphous phase(s) in addition to the crystalline calcium carbonate phases in the reactive carbonate material. The presence of carboaluminate phases as a result of the interaction of the reactive carbonate materials with ordinary portland cement was also confirmed. A Life Cycle Assessment was completed for several cases based on different Calera process configurations and compared against the life cycle of ordinary portland cement. In addition to the materials development efforts, the Calera technology for the production of product using an innovative building materials demonstration plant was developed beyond conceptual engineering to a detailed design with a construction schedule and cost estimate.« less

Modular Organization of Exploratory Force Development Under Isometric Conditions in the Human Arm.

PubMed

Roh, Jinsook; Lee, Sang Wook; Wilger, Kevin D

2018-01-31

Muscle coordination of isometric force production can be explained by a smaller number of modules. Variability in force output, however, is higher during exploratory/transient force development phases than force maintenance phase, and it is not clear whether the same modular structure underlies both phases. In this study, eight neurologically-intact adults isometrically performed target force matches in 54 directions at hands, and electromyographic (EMG) data from eight muscles were parsed into four sequential phases. Despite the varying degree of motor complexity across phases (significant between-phase differences in EMG-force correlation, angular errors, and between-force correlations), the number/composition of motor modules were found equivalent across phases, suggesting that the CNS systematically modulated activation of the same set of motor modules throughout sequential force development.

Product assurance policies and procedures for flight dynamics software development

NASA Technical Reports Server (NTRS)

Perry, Sandra; Jordan, Leon; Decker, William; Page, Gerald; Mcgarry, Frank E.; Valett, Jon

1987-01-01

The product assurance policies and procedures necessary to support flight dynamics software development projects for Goddard Space Flight Center are presented. The quality assurance and configuration management methods and tools for each phase of the software development life cycles are described, from requirements analysis through acceptance testing; maintenance and operation are not addressed.

Characterization of a whole, inactivated influenza (H5N1) vaccine.

PubMed

Tada, Yoshikazu

2008-11-01

Effective vaccines against the highly pathogenic influenza A/H5N1 virus are being developed worldwide. In Japan, two adjuvanted, inactivated, whole-virion influenza vaccines were recently developed and licensed as mock-up, pre-pandemic vaccine formulations by the Ministry of Health and Labor Welfare of Japan. During the vaccine design and development process, various obstacles were overcome and, in this report, we introduce the non clinical production, immunogenicity data in human and development process that was associated with egg-derived adjuvanted, inactivated, whole-virion influenza A (H5N1) vaccine. Pilot lots of H5N1 vaccine were produced using the avirulent H5N1 reference strain A/Vietnam/1194/2004 (H5N1) NIBRG-14 and administered following adsorption with aluminum hydroxide as an adjuvant. Quality control and formulation stability tests were performed before clinical trials were initiated (phase I-III). The research foundation for microbial diseases of Osaka University (BIKEN) carried out vaccine production, quality control, stability testing and the phase I clinical trial in addition to overseeing the licensing of this vaccine. Mitsubishi Chemical Safety Institute Ltd. carried out the non clinical pharmacological toxicity and safety studies and the Japanese medical association carried out the phase II/III trials. Phase I-III trials took place in 2006. The production processes were well controlled by established tests and validations. Vaccine quality was confirmed by quality control, stability and pre-clinical tests, and the vaccine was approved as a mock-up, pre-pandemic vaccine by the Ministry of Health and Labor Welfare of Japan. Numerous safety and efficacy procedures were carried out prior to the approval of the described vaccine formulation. Some of these procedures were of particular importance e.g., vaccine development, validation, and quality control tests that included strict monitoring of the hemagglutinin (HA) content of the vaccine formulations. Improving vaccine productivity, shortening the production period and improving antigen yield of the avirulent vaccine strains were also considered important vaccine development criteria.

Advanced manufacturing development of a composite empennage component for L-1011 aircraft

NASA Technical Reports Server (NTRS)

Alva, T.; Henkel, J.; Johnson, R.; Carll, B.; Jackson, A.; Mosesian, B.; Brozovic, R.; Obrien, R.; Eudaily, R.

1982-01-01

This is the final report of technical work conducted during the fourth phase of a multiphase program having the objective of the design, development and flight evaluation of an advanced composite empennage component manufactured in a production environment at a cost competitive with those of its metal counterpart, and at a weight savings of at least 20 percent. The empennage component selected for this program is the vertical fin box of the L-1011 aircraft. The box structure extends from the fuselage production joint to the tip rib and includes front and rear spars. During Phase 4 of the program, production quality tooling was designed and manufactured to produce three sets of covers, ribs, spars, miscellaneous parts, and subassemblies to assemble three complete ACVF units. Recurring and nonrecurring cost data were compiled and documented in the updated producibility/design to cost plan. Nondestruct inspections, quality control tests, and quality acceptance tests were performed in accordance with the quality assurance plan and the structural integrity control plan. Records were maintained to provide traceability of material and parts throughout the manufacturing development phase. It was also determined that additional tooling would not be required to support the current and projected L-1011 production rate.

UST CORRECTIVE ACTION TECHNOLOGIES: ENGINEERING DESIGN OF FREE PRODUCT RECOVERY SYSTEMS

EPA Science Inventory

The objective of this project was to develop a technical assistance document for assessment of subsurface hydrocarbon spills and for evaluating effects of well placement and pumping rates on separate phase plume control and on free product recovery. Procedures developed for estim...

Mechanistic approach for nitride fuel evolution and fission product release under irradiation

NASA Astrophysics Data System (ADS)

Dolgodvorov, A. P.; Ozrin, V. D.

2017-01-01

A model for describing uranium-plutonium mixed nitride fuel pellet burning was developed. Except fission products generating, the model includes impurities of oxygen and carbon. Nitrogen behaviour in nitride fuel was analysed and the nitrogen chemical potential in solid solution with uranium-plutonium nitride was constructed. The chemical program module was tested with the help of thermodynamic equilibrium phase distribution calculation. Results were compared with analogous data in literature, quite good agreement was achieved, especially for uranium sesquinitride, metallic species and some oxides. Calculation of a process of nitride fuel burning was also conducted. Used mechanistic approaches for fission product evolution give the opportunity to find fission gas release fractions and also volumes of intergranular secondary phases. Calculations present that the most massive secondary phases are the oxide and metallic phases. Oxide phase contain approximately 1 % wt of substance over all time of burning with slightly increasing of content. Metallic phase has considerable rising of mass and by the last stage of burning it contains about 0.6 % wt of substance. Intermetallic phase has less increasing rate than metallic phase and include from 0.1 to 0.2 % wt over all time of burning. The highest element fractions of released gaseous fission products correspond to caesium and iodide.

Recommended approach to sofware development

NASA Technical Reports Server (NTRS)

Mcgarry, F. E.; Page, J.; Eslinger, S.; Church, V.; Merwarth, P.

1983-01-01

A set of guideline for an organized, disciplined approach to software development, based on data collected and studied for 46 flight dynamics software development projects. Methods and practices for each phase of a software development life cycle that starts with requirements analysis and ends with acceptance testing are described; maintenance and operation is not addressed. For each defined life cycle phase, guidelines for the development process and its management, and the products produced and their reviews are presented.

A novel direct screening method for alkyl glucoside production by glucosidases expressed in E. coli in 96-well plates.

PubMed

Gräber, Martin; Andersson, Mats; Rundbäck, Fabian; Pozzo, Tania; Karlsson, Eva Nordberg; Adlercreutz, Patrick

2010-01-15

The present work describes the development of a novel direct screening method, assayed in 96-well format, for evaluation of enzymatic alkyl glycoside production in a hexanol-water two-phase system. Alkyl glycosides are surfactants with a range of applications and with good biodegradability and low toxicity. Enzymatic synthesis makes it possible to prepare beta-d-glucopyranosides with high purity. In the developed screening assay, hexyl-beta-d-glucopyranoside was chosen as a model product to be synthesised by reversed hydrolysis in a water-hexanol two-phase system. In a first step the model product is produced by glucosidases expressed in E. coli cells in 96-deep-well plates. After phase separation, the hexyl-beta-d-glucopyranoside in the organic phase is degraded enzymatically and the released glucose detected spectrophotometrically at 405nm utilizing peroxidase/glucose oxidase, and the reagent 2,2'-azino-bis(3-ethylbenzthiazoline-6-sulphonic acid) (ABTS). The aqueous phase is used to monitor hydrolysis of p-NPG at 405nm, allowing use of a ratio of the two assays to compensate for expression differences. The complete method was used for comparison of two different beta-glucosidases, classified under glycoside hydrolase family 1 and 3, respectively, showing a significant difference in their ability to synthesise hexyl-beta-d-glucopyranoside by reversed hydrolysis.

Development of a phase-sensitive Fourier domain optical coherence tomography system to measure mouse organ of Corti vibrations in two cochlear turns

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramamoorthy, Sripriya; Zhang, Yuan; Jacques, Steven

In this study, we have developed a phase-sensitive Fourier-domain optical coherence tomography system to simultaneously measure the in vivo inner ear vibrations in the hook area and second turn of the mouse cochlea. This technical development will enable measurement of intra-cochlear distortion products at ideal locations such as the distortion product generation site and reflection site. This information is necessary to un-mix the complex mixture of intra-cochlear waves comprising the DPOAE and thus leads to the non-invasive identification of the local region of cochlear damage.

48 CFR 34.005-6 - Full production.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Full production. 34.005-6... OF CONTRACTING MAJOR SYSTEM ACQUISITION General 34.005-6 Full production. Contracts for full production of successfully tested major systems selected from the full-scale development phase may be awarded...

SHARP's systems engineering challenge: rectifying integrated product team requirements with performance issues in an evolutionary spiral development acquisition

NASA Astrophysics Data System (ADS)

Kuehl, C. Stephen

2003-08-01

Completing its final development and early deployment on the Navy's multi-role aircraft, the F/A-18 E/F Super Hornet, the SHAred Reconnaissance Pod (SHARP) provides the war fighter with the latest digital tactical reconnaissance (TAC Recce) Electro-Optical/Infrared (EO/IR) sensor system. The SHARP program is an evolutionary acquisition that used a spiral development process across a prototype development phase tightly coupled into overlapping Engineering and Manufacturing Development (EMD) and Low Rate Initial Production (LRIP) phases. Under a tight budget environment with a highly compressed schedule, SHARP challenged traditional acquisition strategies and systems engineering (SE) processes. Adopting tailored state-of-the-art systems engineering process models allowd the SHARP program to overcome the technical knowledge transition challenges imposed by a compressed program schedule. The program's original goal was the deployment of digital TAC Recce mission capabilities to the fleet customer by summer of 2003. Hardware and software integration technical challenges resulted from requirements definition and analysis activities performed across a government-industry led Integrated Product Team (IPT) involving Navy engineering and test sites, Boeing, and RTSC-EPS (with its subcontracted hardware and government furnished equipment vendors). Requirements development from a bottoms-up approach was adopted using an electronic requirements capture environment to clarify and establish the SHARP EMD product baseline specifications as relevant technical data became available. Applying Earned-Value Management (EVM) against an Integrated Master Schedule (IMS) resulted in efficiently managing SE task assignments and product deliveries in a dynamically evolving customer requirements environment. Application of Six Sigma improvement methodologies resulted in the uncovering of root causes of errors in wiring interconnectivity drawings, pod manufacturing processes, and avionics requirements specifications. Utilizing the draft NAVAIR SE guideline handbook and the ANSI/EIA-632 standard: Processes for Engineering a System, a systems engineering tailored process approach was adopted for the accelerated SHARP EMD prgram. Tailoring SE processes in this accelerated product delivery environment provided unique opportunities to be technically creative in the establishment of a product performance baseline. This paper provides an historical overview of the systems engineering activities spanning the prototype phase through the EMD SHARP program phase, the performance requirement capture activities and refinement process challenges, and what SE process improvements can be applied to future SHARP-like programs adopting a compressed, evolutionary spiral development acquisition paradigm.

The Application of Concurrent Engineering Tools and Design Structure Matrix in Designing Tire

NASA Astrophysics Data System (ADS)

Ginting, Rosnani; Fachrozi Fitra Ramadhan, T.

2016-02-01

The development of automobile industry in Indonesia is growing rapidly. This phenomenon causes companies related to the automobile industry such as tire industry must develop products based on customers’ needs and considering the timeliness of delivering the product to the customer. It could be reached by applying strategic planning in developing an integrated concept of product development. This research was held in PT. XYZ that applied the sequential approach in designing and developing products. The need to improve in one stage of product development could occur re-designing that needs longer time in developing a new product. This research is intended to get an integrated product design concept of tire pertaining to the customer's needs using Concurrent Engineering Tools by implementing the two-phased of product development. The implementation of Concurrent Engineering approach results in applying the stage of project planning, conceptual design, and product modules. The product modules consist of four modules that using Product Architecture - Design Structure Matrix to ease the designing process of new product development.

Space Shuttle External Tank Project status

NASA Technical Reports Server (NTRS)

Davis, R. M.

1980-01-01

The External Tank Project is reviewed with emphasis on the DDT&E and production phases and the lightweight tank development. It is noted that the DDT&E phase is progressing well with the structural and ground vibration test article programs complete, the propulsion test article program progressing well, and the component qualification and verification testing 92% complete. New tools and facilities are being brought on line to support the increased build rate for the production phase. The lightweight tank, which will provide additional payload in orbit, is progressing to schedule with first delivery in early 1982.

New developments in optical phase-change memory

NASA Astrophysics Data System (ADS)

Ovshinsky, Stanford R.; Czubatyj, Wolodymyr

2001-02-01

Phase change technology has progressed from the original invention of Ovshinsky to become the leading choice for rewritable optical disks. ECD's early work in phase change materials and methods for operating in a direct overwrite fashion were crucial to the successes that have been achieved. Since the introduction of the first rewritable phase change products in 1991, the market has expanded from CD-RW into rewritable DVD with creative work going on worldwide. Phase change technology is ideally suited to address the continuous demand for increased storage capacity. First, laser beams can be focused to ever-smaller spot sizes using shorter wavelength lasers and higher performance optics. Blue lasers are now commercially viable and high numerical aperture and near field lenses have been demonstrated. Second, multilevel approaches can be used to increase capacity by a factor of three or more with concomitant increases in data transfer rate. In addition, ECD has decreased manufacturing costs through the use of innovative production technology. These factors combine to accelerate the widespread use of phase change technology. As in all our technologies, such as thin film photovoltaics, nickel metal hydride batteries, hydrogen storage systems, fuel cells, electrical memory, etc., we have invented the materials, the products, the production machines and the production processes for high rate, low-cost manufacture.

[Hope for patients with rare diseases--"orphan" drugs].

PubMed

Kuzelová, M; Kubácková, K; Palágyi, M; Smíd, M

2006-01-01

Rare diseases are defined as those affected less than five in every 10 000 person in European Union. The purpose of this paper is to present activities, which make possible to stimulate research development and marketing of appropriate medicine for tretment of rare disease, named "Orphan" medicinal products. EU "Orphan" medicinal products legislation which entered into force in April 2000 is described. Definition of "Orphan" medicinal products as well as the procedure of designation and placing the products into the Community register is presented. Those incentives to industry are described, which are already five years very well implemented oh the European level mostly on the pre-authorisation phase of "Orphan" medicinal products development, but also in the registration process as well as the post-authorisation phase. Finaly, the first twenty "Orphan" medicinal products, which have been given positive opinion in the Community for the grant of a marketing authorisation till April 2005 are mentioned in this work. The real availability of "Orphan" medicinal products in the particular EU member states is analysed.

Phase-synchronisation in continuous flow models of production networks

NASA Astrophysics Data System (ADS)

Scholz-Reiter, Bernd; Tervo, Jan Topi; Freitag, Michael

2006-04-01

To improve their position at the market, many companies concentrate on their core competences and hence cooperate with suppliers and distributors. Thus, between many independent companies strong linkages develop and production and logistics networks emerge. These networks are characterised by permanently increasing complexity, and are nowadays forced to adapt to dynamically changing markets. This factor complicates an enterprise-spreading production planning and control enormously. Therefore, a continuous flow model for production networks will be derived regarding these special logistic problems. Furthermore, phase-synchronisation effects will be presented and their dependencies to the set of network parameters will be investigated.

Automated solar panel assembly line

NASA Technical Reports Server (NTRS)

Somberg, H.

1981-01-01

The initial stage of the automated solar panel assembly line program was devoted to concept development and proof of approach through simple experimental verification. In this phase, laboratory bench models were built to demonstrate and verify concepts. Following this phase was machine design and integration of the various machine elements. The third phase was machine assembly and debugging. In this phase, the various elements were operated as a unit and modifications were made as required. The final stage of development was the demonstration of the equipment in a pilot production operation.

[Modeling developmental aspects of sensorimotor control of speech production].

PubMed

Kröger, B J; Birkholz, P; Neuschaefer-Rube, C

2007-05-01

Detailed knowledge of the neurophysiology of speech acquisition is important for understanding the developmental aspects of speech perception and production and for understanding developmental disorders of speech perception and production. A computer implemented neural model of sensorimotor control of speech production was developed. The model is capable of demonstrating the neural functions of different cortical areas during speech production in detail. (i) Two sensory and two motor maps or neural representations and the appertaining neural mappings or projections establish the sensorimotor feedback control system. These maps and mappings are already formed and trained during the prelinguistic phase of speech acquisition. (ii) The feedforward sensorimotor control system comprises the lexical map (representations of sounds, syllables, and words of the first language) and the mappings from lexical to sensory and to motor maps. The training of the appertaining mappings form the linguistic phase of speech acquisition. (iii) Three prelinguistic learning phases--i. e. silent mouthing, quasi stationary vocalic articulation, and realisation of articulatory protogestures--can be defined on the basis of our simulation studies using the computational neural model. These learning phases can be associated with temporal phases of prelinguistic speech acquisition obtained from natural data. The neural model illuminates the detailed function of specific cortical areas during speech production. In particular it can be shown that developmental disorders of speech production may result from a delayed or incorrect process within one of the prelinguistic learning phases defined by the neural model.

Enhanced production of bioethanol from waste of beer fermentation broth at high temperature through consecutive batch strategy by simultaneous saccharification and fermentation.

PubMed

Khattak, Waleed Ahmad; Khan, Taous; Ha, Jung Hwan; Ul-Islam, Mazhar; Kang, Min-Kyung; Park, Joong Kon

2013-10-10

Malt hydrolyzing enzymes and yeast glycolytic and fermentation enzymes in the waste from beer fermentation broth (WBFB) were identified by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). A new 'one-pot consecutive batch strategy' was developed for efficient bio-ethanol production by simultaneous saccharification and fermentation (SSF) using WBFB without additional enzymes, microbial cells, or carbohydrates. Bio-ethanol production was conducted in batches using WBFB supernatant in the first phase at 25-67°C and 50rpm, followed by the addition of 3% WBFB solid residue to the existing culture broth in the second phase at 67°C. The ethanol production increased from 50 to 102.5g/L when bare supernatant was used in the first phase, and then to 219g ethanol/L in the second phase. The amount of ethanol obtained using this strategy was almost equal to that obtained using the original WBFB containing 25% solid residue at 33°C, and more than double that obtained when bare supernatant was used. Microscopic and gel electrophoresis studies revealed yeast cell wall degradation and secretion of cellular material into the surrounding medium. Scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) supported the existence of enzymes in WBFB involved in bioethanol production at elevated temperatures. The results of this study will provide insight for the development of new strategies for biofuel production. Copyright © 2013 Elsevier Inc. All rights reserved.

Parent Reports of Young Spanish-English Bilingual Children's Productive Vocabulary: A Development and Validation Study

ERIC Educational Resources Information Center

Mancilla-Martinez, Jeannette; Gámez, Perla B.; Vagh, Shaher Banu; Lesaux, Nonie K.

2016-01-01

Purpose: This 2-phase study aims to extend research on parent report measures of children's productive vocabulary by investigating the development (n = 38) of the Spanish Vocabulary Extension and validity (n = 194) of the 100-item Spanish and English MacArthur-Bates Communicative Development Inventories Toddler Short Forms and Upward Extension…

Development of advanced silicon solar cells for Space Station Freedom

NASA Technical Reports Server (NTRS)

Lillington, David R.

1990-01-01

This report describes the development of large area high efficiency wrapthrough solar cells for Space Station Freedom. The goal of this contract was the development and fabrication of 8 x 8 cm coplanar back contact solar cells with a minimum output of 1.039 watts/cell. The first task in this program was a modeling study to determine the optimum configuration of the cell and to study the effects of surface passivation, substrate resistivity, and back surface field on the BOL and EOL performance. In addition, the optical stack, including the cell cover, AR coatings, and Kapton blanket, was modeled to optimize 'on orbit' operation. The second phase was a manufacturing development phase to develop high volume manufacturing processes for the reliable production of low recombination velocity boron back surface fields, techniques to produce smooth, low leakage wrapthrough holes, passivation, photoresist application methods, and metallization schemes. The final portion of this program was a pilot production phase. Seven hundred solar cells were delivered in this phase. At the end of the program, cells with average efficiencies over 13 percent were being produced with power output in excess of 1.139 watts/cell, thus substantially exceeding the program goal.

Cellular Therapies Clinical Research Roadmap: Lessons learned on how to move a cellular therapy into a clinical trial

PubMed Central

Ouseph, Stacy; Tappitake, Darah; Armant, Myriam; Wesselschmidt, Robin; Derecho, Ivy; Draxler, Rebecca; Wood, Deborah; Centanni, John M.

2014-01-01

A clinical research roadmap has been developed as a resource for researchers to identify critical areas and potential pitfalls when transitioning a cellular therapy product from the research laboratory, via and Investigational New Drug (IND) application, into early phase clinical trials. The roadmap describes four key areas; basic and preclinical research, resource development, translational research and good manufacturing practice (GMP), and IND assembly and submission. Basic and preclinical research identifies a new therapeutic concept and demonstrates its potential value using a model of the relevant disease. During resource development the appropriate specialists and the required expertise to bring this product into the clinic are identified (e.g., researchers, regulatory specialists, GMP manufacturing staff, clinicians, and clinical trials staff, etc.). Additionally, the funds required to achieve this goal (or a plan to procure them) are identified. In the next phase the plan to translate the research product into a clinical grade therapeutic is developed. Finally regulatory approval to start the trial must be obtained. In the United States this is done by filing an IND application with the Food and Drug Administration. The NHLBI-funded Production Assistance for Cellular Therapies (PACT) program has facilitated the transition of a variety of cellular therapy products from the laboratory into Phase1/2 trials. The five PACT facilities have assisted investigators by performing translational studies and GMP manufacturing to ensure that cellular products met release specifications and were manufactured safely, reproducibly, and at the appropriate scale. The roadmap resulting from this experience is the focus of this article. PMID:25484311

Implementation of a production Ada project: The GRODY study

NASA Technical Reports Server (NTRS)

Godfrey, Sara; Brophy, Carolyn Elizabeth

1989-01-01

The use of the Ada language and design methodologies that encourage full use of its capabilities have a strong impact on all phases of the software development project life cycle. At the National Aeronautics and Space Administration/Goddard Space Flight Center (NASA/GSFC), the Software Engineering Laboratory (SEL) conducted an experiment in parallel development of two flight dynamics systems in FORTRAN and Ada. The differences observed during the implementation, unit testing, and integration phases of the two projects are described and the lessons learned during the implementation phase of the Ada development are outlined. Included are recommendations for future Ada development projects.

Biomass plug development and propagation in porous media.

PubMed

Stewart, T L; Fogler, H S

2001-02-05

Exopolymer-producing bacteria can be used to modify soil profiles for enhanced oil recovery or bioremediation. Understanding the mechanisms associated with biomass plug development and propagation is needed for successful application of this technology. These mechanisms were determined from packed-bed and micromodel experiments that simulate plugging in porous media. Leuconostoc mesenteroides was used, because production of dextran, a water-insoluble exopolymer, can be controlled by using different carbon sources. As dextran was produced, the pressure drop across the porous media increased and began to oscillate. Three pressure phases were identified under exopolymer-producing conditions: the exopolymer-induction phase, the plugging phase, and the plug-propagation phase. The exopolymer-induction phase extended from the time that exopolymer-producing conditions were induced until there was a measurable increase in pressure drop across the porous media. The plugging phase extended from the first increase in pressure drop until a maximum pressure drop was reached. Changes in pressure drop in these two phases were directly related to biomass distribution. Specifically, flow channels within the porous media filled with biomass creating a plugged region where convective flow occurred only in water channels within the biofilm. These water channels were more restrictive to flow causing the pressure drop to increase. At a maximum pressure drop across the porous media, the biomass yielded much like a Bingham plastic, and a flow channel was formed. This behavior marked the onset of the plug-propagation phase which was characterized by sequential development and breakthrough of biomass plugs. This development and breakthrough propagated the biomass plug in the direction of nutrient flow. The dominant mechanism associated with all three phases of plugging in porous media was exopolymer production; yield stress is an additional mechanism in the plug-propagation phase. Copyright 2001 John Wiley & Sons, Inc.

Using a social robot to teach gestural recognition and production in children with autism spectrum disorders.

PubMed

So, Wing-Chee; Wong, Miranda Kit-Yi; Lam, Carrie Ka-Yee; Lam, Wan-Yi; Chui, Anthony Tsz-Fung; Lee, Tsz-Lok; Ng, Hoi-Man; Chan, Chun-Hung; Fok, Daniel Chun-Wing

2017-07-04

While it has been argued that children with autism spectrum disorders are responsive to robot-like toys, very little research has examined the impact of robot-based intervention on gesture use. These children have delayed gestural development. We used a social robot in two phases to teach them to recognize and produce eight pantomime gestures that expressed feelings and needs. Compared to the children in the wait-list control group (N = 6), those in the intervention group (N = 7) were more likely to recognize gestures and to gesture accurately in trained and untrained scenarios. They also generalized the acquired recognition (but not production) skills to human-to-human interaction. The benefits and limitations of robot-based intervention for gestural learning were highlighted. Implications for Rehabilitation Compared to typically-developing children, children with autism spectrum disorders have delayed development of gesture comprehension and production. Robot-based intervention program was developed to teach children with autism spectrum disorders recognition (Phase I) and production (Phase II) of eight pantomime gestures that expressed feelings and needs. Children in the intervention group (but not in the wait-list control group) were able to recognize more gestures in both trained and untrained scenarios and generalize the acquired gestural recognition skills to human-to-human interaction. Similar findings were reported for gestural production except that there was no strong evidence showing children in the intervention group could produce gestures accurately in human-to-human interaction.

Cellular Therapies Clinical Research Roadmap: lessons learned on how to move a cellular therapy into a clinical trial.

PubMed

Ouseph, Stacy; Tappitake, Darah; Armant, Myriam; Wesselschmidt, Robin; Derecho, Ivy; Draxler, Rebecca; Wood, Deborah; Centanni, John M

2015-04-01

A clinical research roadmap has been developed as a resource for researchers to identify critical areas and potential pitfalls when transitioning a cellular therapy product from the research laboratory, by means of an Investigational New Drug (IND) application, into early-phase clinical trials. The roadmap describes four key areas: basic and preclinical research, resource development, translational research and Good Manufacturing Practice (GMP) and IND assembly and submission. Basic and preclinical research identifies a new therapeutic concept and demonstrates its potential value with the use of a model of the relevant disease. During resource development, the appropriate specialists and the required expertise to bring this product into the clinic are identified (eg, researchers, regulatory specialists, GMP manufacturing staff, clinicians and clinical trials staff, etc). Additionally, the funds required to achieve this goal (or a plan to procure them) are identified. In the next phase, the plan to translate the research product into a clinical-grade therapeutic is developed. Finally regulatory approval to start the trial must be obtained. In the United States, this is done by filing an IND application with the Food and Drug Administration. The National Heart, Lung and Blood Institute-funded Production Assistance for Cellular Therapies program has facilitated the transition of a variety of cellular therapy products from the laboratory into Phase1/2 trials. The five Production Assistance for Cellular Therapies facilities have assisted investigators by performing translational studies and GMP manufacturing to ensure that cellular products met release specifications and were manufactured safely, reproducibly and at the appropriate scale. The roadmap resulting from this experience is the focus of this article. Copyright © 2015 International Society for Cellular Therapy. Published by Elsevier Inc. All rights reserved.

Recommended approach to software development, revision 3

NASA Technical Reports Server (NTRS)

Landis, Linda; Waligora, Sharon; Mcgarry, Frank; Pajerski, Rose; Stark, Mike; Johnson, Kevin Orlin; Cover, Donna

1992-01-01

Guidelines for an organized, disciplined approach to software development that is based on studies conducted by the Software Engineering Laboratory (SEL) since 1976 are presented. It describes methods and practices for each phase of a software development life cycle that starts with requirements definition and ends with acceptance testing. For each defined life cycle phase, guidelines for the development process and its management, and for the products produced and their reviews are presented.

Production method of carbamazepine/saccharin cocrystal particles by using two solution mixing based on the ternary phase diagram

NASA Astrophysics Data System (ADS)

Kudo, Shoji; Takiyama, Hiroshi

2014-04-01

In the pharmaceutical field, improvement of drug solubility is required, and an interest in cocrystals is growing. Crystallization methods for industrial production of cocrystals have not been developed enough whereas many cocrystals have been prepared in order to find a new crystal form by screening in the laboratory. The objective of this study was the development of the crystallization method which is useful for the industrial production of cocrystal particles based on the phase diagram. A cocrystal of carbamazepine and saccharin was selected as a model substance. The ternary phase diagram of carbamazepine and saccharin in methanol at 303 K was measured. A cocrystallization method of mixing two kinds of different eutectic solutions was designed based on the ternary phase diagram. In order to adjust the cocrystallization conditions, the determination method of the driving force for cocrystal deposition such as supersaturation based on mass balance was proposed. The cocrystal particles were obtained under all the conditions of the five mixing ratios. From these experimental results, the relationship between the supersaturation and the induction time for nucleation was confirmed as well as conventional crystallization. In conclusion, the crystallization method for industrial production of cocrystal particles including the determination of the supersaturation was suggested.

Remote operated vehicle with CO{sub 2} blasting (ROVCO{sub 2}): Volume 1. Final report, September 1993--July 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-06-01

This report documents the second phase of the Remote Operated Vehicle with CO{sub 2} Blasting (ROVCO{sub 2}) Program. The ROVCO{sub 2} Program`s goal is to develop and demonstrate a tool to improve the productivity of concrete floor decontamination. The second phase integrated non-developmental subsystems on to the ROVCO{sub 2} system and performed quantitative decontamination effectiveness, productivity, and reliability testings. The report documents these development activities and the analysis of cost and performance. The results show that the ROVCO{sub 2} system is an efficient decontamination tool.

Separation of aromatic carboxylic acids using quaternary ammonium salts on reversed-phase HPLC. 2. Application for the analysis of Loy Yang coal oxidation products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kawamura, K.; Okuwaki, A.; Verheyen, T.V.

In order to develop separation processes and analytical methods for aromatic carboxylic acids for the coal oxidation products, the separation behavior of aromatic carboxylic acids on a reversed-phase HPLC using eluent containing quaternary ammonium salt was optimized using the solvent gradient method. This method was applied for the analysis of Loy Yang coal oxidation products. It was confirmed that the analytical data using this method were consistent with those determined using gas chromatography.

Characteristics of rare disease marketing applications associated with FDA product approvals 2006-2010.

PubMed

Pariser, Anne R; Slack, Daniel J; Bauer, Larry J; Warner, Catherine A; Tracy, LaRee A

2012-08-01

New drug and biologic product marketing applications submitted to FDA's Center for Drug Evaluation and Research (CDER) between 2006 and 2010 were analyzed to identify rare disease application characteristics associated with higher approval rates. The results show that approval rates were similar for rare and common disease applications. Larger company size, prior regulatory experience and priority review designation were associated with higher approval rates. The study findings show that rare disease product development is feasible, and increased interactions between product developers and FDA in early investigational phases can facilitate product development. Published by Elsevier Ltd.

Implementation of AMNOG: An industry perspective

PubMed Central

Chuang‐Stein, Christy

2015-01-01

In 2010, the Federal Parliament (Bundestag) of Germany passed a new law (Arzneimittelmarktneuordnungsgesetz, AMNOG) on the regulation of medicinal products that applies to all pharmaceutical products with active ingredients that are launched beginning January 1, 2011. The law describes the process to determine the price at which an approved new product will be reimbursed by the statutory health insurance system. The process consists of two phases. The first phase assesses the additional benefit of the new product versus an appropriate comparator (zweckmäßige Vergleichstherapie, zVT). The second phase involves price negotiation. Focusing on the first phase, this paper investigates requirements of benefit assessment of a new product under this law with special attention on the methods applied by the German authorities on issues such as the choice of the comparator, patient relevant endpoints, subgroup analyses, extent of benefit, determination of net benefit, primary and secondary endpoints, and uncertainty of the additional benefit. We propose alternative approaches to address the requirements in some cases and invite other researchers to help develop solutions in other cases. PMID:26332597

Natural product and natural product derived drugs in clinical trials.

PubMed

Butler, Mark S; Robertson, Avril A B; Cooper, Matthew A

2014-11-01

There are a significant number of natural product (NP) drugs in development. We review the 100 NP and NP-derived compounds and 33 Antibody Drug Conjugates (ADCs) with a NP-derived cytotoxic component being evaluated in clinical trials or in registration at the end of 2013. 38 of these compounds and 33 ADCs are being investigated as potential oncology treatments, 26 as anti-infectives, 19 for the treatment of cardiovascular and metabolic diseases, 11 for inflammatory and related diseases and 6 for neurology. There was a spread of the NP and NP-derived compounds through the different development phases (17 in phase I, 52 in phase II, 23 in phase III and 8 NDA and/or MAA filed), while there were 23 ADCs in phase I and 10 in phase II. 50 of these 100 compounds were either NPs or semi-synthetic (SS) NPs, which indicated the original NP still plays an important role. NP and NP-derived compounds for which clinical trials have been halted or discontinued since 2008 are listed in the Supplementary Information. The 25 NP and NP-derived drugs launched since 2008 are also reviewed, and late stage development candidates and new NP drug pharmacophores analysed. The short term prospect for new NP and NP-derived drug approvals is bright, with 31 compounds in phase III or in registration, which should ensure a steady stream of approvals for at least the next five years. However, there could be future issues for new drug types as only five new drug pharmacophores discovered in the last 15 years are currently being evaluated in clinical trials. The next few years will be critical for NP-driven lead discovery, and a concerted effort is required to identify new biologically active pharmacophores and to progress these and existing compounds through pre-clinical drug development into clinical trials.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levy, E.; Mullens, M.; Rath, P.

The Advanced Envelope Research effort will provide factory homebuilders with high performance, cost-effective envelope designs that can be effectively integrated into the plant production process while meeting the thermal requirements of the 2012 IECC standards. Given the affordable nature of manufactured homes, impact on first cost is a major consideration in developing new envelope technologies. This work is part of a multi-phase effort. Phase 1 identified seven envelope technologies and provided a preliminary assessment of three methods for building high performance walls. Phase 2 focused on developing viable product designs, manufacturing strategies, addressing code and structural issues, and cost analysismore » of the three selected options. An industry advisory committee helped narrow the research focus to perfecting a stud wall design with exterior continuous insulation (CI). Phase 3, completed in two stages, continued the design development effort, exploring and evaluating a range or methods for applying CI to factory built homes. The scope also included material selection, manufacturing and cost analysis, and prototyping and testing. During this phase, a home was built with CI, evaluated, and placed in service. The experience of building a mock up wall section with CI and then constructing on line a prototype home resolved important concerns about how to integrate the material into the production process. First steps were taken toward finding least expensive approaches for incorporating CI in standard factory building practices and a preliminary assessment suggested that even at this early stage the technology is attractive when viewed from a life cycle cost perspective.« less

Organic Phase Change Nanoparticles for in-Product Labeling of Agrochemicals.

PubMed

Wang, Miao; Duong, Binh; Su, Ming

2015-10-28

There is an urgent need to develop in-product covert barcodes for anti-counterfeiting of agrochemicals. This paper reports a new organic nanoparticle-based in-product barcode system, in which a panel of organic phase change nanoparticles is added as a barcode into in a variety of chemicals (herein agrochemicals). The barcode is readout by detecting melting peaks of organic nanoparticles using differential scanning calorimetry. This method has high labeling capacity due to small sizes of nanoparticles, sharp melting peaks, and large scan range of thermal analysis. The in-product barcode can be effectively used to protect agrochemical products from being counterfeited due to its large coding capacity, technical readiness, covertness, and robustness.

Stochastic production phase design for an open pit mining complex with multiple processing streams

NASA Astrophysics Data System (ADS)

Asad, Mohammad Waqar Ali; Dimitrakopoulos, Roussos; van Eldert, Jeroen

2014-08-01

In a mining complex, the mine is a source of supply of valuable material (ore) to a number of processes that convert the raw ore to a saleable product or a metal concentrate for production of the refined metal. In this context, expected variation in metal content throughout the extent of the orebody defines the inherent uncertainty in the supply of ore, which impacts the subsequent ore and metal production targets. Traditional optimization methods for designing production phases and ultimate pit limit of an open pit mine not only ignore the uncertainty in metal content, but, in addition, commonly assume that the mine delivers ore to a single processing facility. A stochastic network flow approach is proposed that jointly integrates uncertainty in supply of ore and multiple ore destinations into the development of production phase design and ultimate pit limit. An application at a copper mine demonstrates the intricacies of the new approach. The case study shows a 14% higher discounted cash flow when compared to the traditional approach.

Experimental investigation of the combustion products in an aluminised solid propellant

NASA Astrophysics Data System (ADS)

Liu, Zhu; Li, Shipeng; Liu, Mengying; Guan, Dian; Sui, Xin; Wang, Ningfei

2017-04-01

Aluminium is widely used as an important additive to improve ballistic and energy performance in solid propellants, but the unburned aluminium does not contribute to the specific impulse and has both thermal and momentum two-phase flow losses. So understanding of aluminium combustion behaviour during solid propellant burning is significant when improving internal ballistic performance. Recent developments and experimental results reported on such combustion behaviour are presented in this paper. A variety of experimental techniques ranging from quenching and dynamic measurement, to high-speed CCD video recording, were used to study aluminium combustion behaviour and the size distribution of the initial agglomerates. This experimental investigation also provides the size distribution of the condensed phase products. Results suggest that the addition of an organic fluoride compound to solid propellant will generate smaller diameter condensed phase products due to sublimation of AlF3. Lastly, a physico-chemical picture of the agglomeration process was also developed based on the results of high-speed CCD video analysis.

Occurrence assessment for disinfectants and disinfection by-products (phase 6A) in public drinking water. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The EPA Office of Ground Water and Drinking Water is developing national primary drinking water regulations for disinfectant and disinfection by-product contaminants. Thirteen contaminants are being considered to be regulated under Phase 6. These contaminants, referred to as Phase 6a, are the subject of the report. The information is important for setting the Maximum Contaminant Level Goal for a contaminant. The exposure information also is used to estimate the baseline health impact assessment of current levels and for evaluation of the health benefits of the regulatory alternatives.

Broadband metasurfaces enabling arbitrarily large delay-bandwidth products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ginis, Vincent; Tassin, Philippe; Koschny, Thomas

2016-01-19

Metasurfaces allow for advanced manipulation of optical signals by imposing phase discontinuities across flat interfaces. Unfortunately, these phase shifts remain restricted to values between 0 and 2π, limiting the delay-bandwidth product of such sheets. Here, we develop an analytical tool to design metasurfaces that mimic three-dimensional materials of arbitrary thickness. In this way, we demonstrate how large phase discontinuities can be realized by combining several subwavelength Lorentzian resonances in the unit cell of the surface. Finally, our methods open up the temporal response of metasurfaces and may lead to the construction of metasurfaces with a plethora of new optical functions.

Construction of a parallel processor for simulating manipulators and other mechanical systems

NASA Technical Reports Server (NTRS)

Hannauer, George

1991-01-01

This report summarizes the results of NASA Contract NAS5-30905, awarded under phase 2 of the SBIR Program, for a demonstration of the feasibility of a new high-speed parallel simulation processor, called the Real-Time Accelerator (RTA). The principal goals were met, and EAI is now proceeding with phase 3: development of a commercial product. This product is scheduled for commercial introduction in the second quarter of 1992.

The Post-Adolescent Phase: A By-Product and a Factor of Development.

ERIC Educational Resources Information Center

Planck, Ulrich

Conducted in 1955 and 1980, random sample interview data of 17 to 28 year-old West Germans from places of less than 5,000 inhabitants are used to support the thesis that the post-adolescent phase has been prolonged in the countryside of West Germany during these years of increasing technical and economic development. Findings indicate occupational…

NASA's Carbon Monitoring System (CMS) Applications and Application Readiness Levels (ARLs)-An assessment of how all CMS ARLs provide societal benefit.

NASA Astrophysics Data System (ADS)

Escobar, V. M.; Sepulveda Carlo, E.; Delgado Arias, S.

2016-12-01

During the past six years, the NASA Carbon Monitoring System (CMS) Applications effort has been engaging with stakeholders in an effort to make the 52 CMS project user friendly and policy relevant. Congressionally directed, the CMS initiative is a NASA endeavor providing carbon data products that help characterize and understand carbon sources and sinks at local and international scales. All data are freely available, and scaled for local, state, regional, national and international-level resource management. To facilitate user feedback during development, as well as understanding for the type of use and application the CMS data products can provide, the Applications project utilizes the NASA Applied Sciences Program nine step Application Readiness Level (ARL) indices. These are used to track and manage the progression and distribution of funded projects. ARLs are an adaptation of NASA's technology readiness levels (TRLs) used for managing technology and risk and reflects the three main tiers of a project: research, development and deployment. The ARLs are scaled from 1 to 9, research and development (ARL1) to operational and/or decision making ready products (ARL9). The ARLS can be broken up into three phases: Phase 1, discovery and feasibility (ARL 1-3); Phase 2, development testing and validation (ARL 4-6); and Phase 3, integration into Partner's systems (ARL 7-9). The ARLs are designed to inform both scientist and end user of the product maturity and application capability. The CMS initiative has products that range across all ARLs, providing societal benefit at multiple scales. Lower ARLs contribute to formal documents such as the IPCC while others at higher levels provide decision support quantifying the value of carbon data for greenhouse gas (GHG) reduction planning. Most CMS products have an ARL 5, (validation of a product in a relevant environment), meaning the CMS carbon science is actively in a state of science-user engagement. For the user community, ARLs are a litmus test for knowing the type of user feedback and advocacy that can be implemented into the product design. For the scientist, ARLS help communicate (1) the maturity of their science to users who would like to use it for decision making and (2) the intended use of the product.

Safeguarding End-User Military Software

DTIC Science & Technology

2014-12-04

product lines using composi- tional symbolic execution [17] Software product lines are families of products defined by feature commonality and vari...ability, with a well-managed asset base. Recent work in testing of software product lines has exploited similarities across development phases to reuse...feature dependence graph to extract the set of possible interaction trees in a product family. It composes these to incrementally and symbolically

Enhanced Oxidative Dehydrogenation of Ethane with Facilitated Transport Membranes for Low Cost Production of Ethylene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nemser, Stuart; Shangguan, Ning; Pennisi, Kenneth

This SBIR program has been extremely successful. We have met or exceeded all of the key objectives. We have successfully demonstrated the product and process feasibility. Compact Membrane Systems proposed a membrane separation technology which can efficiently separate ethylene from ethane in the presence of H 2O and CO 2. The CMS ethylene/ethane separation will significantly improve the economics of the Oxidative Dehydrogenation (ODH) process. We have developed membranes with high ethylene flux and high ethylene/ethane selectivity. These membranes have also shown good resistance to high concentration CO 2 and CO. Economic analysis shows at least **% cost savings comparedmore » with conventional distillation used for ethylene/ethane separation. Given our success to date, we have been able to establish key direct partnerships with other collaborators. The primary objective of the Phase I program was to develop a stable membrane that is capable of providing very efficient and cost effective production of ethylene from ethane. The CMS fluorinated membrane developed during this program was found to be able to provide very good C 2H 4/C 2H 6 selectivity and outstanding C 2H 4 permeance. With the development of the fast and highly selective ethylene CMS membrane, we have achieved all our Phase I program objectives. This is especially true of the estimated cost of ethylene production that is projected to be over **% less than the conventional method (distillation) at scale applications (** Nm3/h). The final result is better than the Phase I goal of 30% less. In summary, during the Phase I, we developed a CMS membrane with a high C 2H 4 permeance good C 2H 4/C 2H 6 selectivity. The stability and anti-fouling ability of the CMS membrane was demonstrated by exposing the membrane to a C 2H 4/C 2H 6 mixture gas for 7 weeks. A membrane based ODH production and separation system was designed and the economic and engineering evaluation using the VMGSim models predicted a cost of $***. As previously stated this is at least a 35% cost reduction from the conventional methods and higher than the Phase I goal (25% cost reduction). The successful Phase I research attracted the interest from several major industrial players who are willing to provide partnership and support of further research. Successful development of the fluoropolymer membranes for C 2H 4/C 2H 6 separation in the process of ODH will provide significant benefits to the public: 1. Development of a highly economically profitable use of shale gas resource; 2. More economic growth and job creations based on the rich shale gas resource in US; 3. Huge energy savings compared with the conventional production of ethylene.« less

Space Station - An integrated approach to operational logistics support

NASA Technical Reports Server (NTRS)

Hosmer, G. J.

1986-01-01

Development of an efficient and cost effective operational logistics system for the Space Station will require logistics planning early in the program's design and development phase. This paper will focus on Integrated Logistics Support (ILS) Program techniques and their application to the Space Station program design, production and deployment phases to assure the development of an effective and cost efficient operational logistics system. The paper will provide the methodology and time-phased programmatic steps required to establish a Space Station ILS Program that will provide an operational logistics system based on planned Space Station program logistics support.

Two-phase anaerobic digestion of vegetable market waste fraction of municipal solid waste and development of improved technology for phase separation in two-phase reactor.

PubMed

Majhi, Bijoy Kumar; Jash, Tushar

2016-12-01

Biogas production from vegetable market waste (VMW) fraction of municipal solid waste (MSW) by two-phase anaerobic digestion system should be preferred over the single-stage reactors. This is because VMW undergoes rapid acidification leading to accumulation of volatile fatty acids and consequent low pH resulting in frequent failure of digesters. The weakest part in the two-phase anaerobic reactors was the techniques applied for solid-liquid phase separation of digestate in the first reactor where solubilization, hydrolysis and acidogenesis of solid organic waste occur. In this study, a two-phase reactor which consisted of a solid-phase reactor and a methane reactor was designed, built and operated with VMW fraction of Indian MSW. A robust type filter, which is unique in its implementation method, was developed and incorporated in the solid-phase reactor to separate the process liquid produced in the first reactor. Experiments were carried out to assess the long term performance of the two-phase reactor with respect to biogas production, volatile solids reduction, pH and number of occurrence of clogging in the filtering system or choking in the process liquid transfer line. The system performed well and was operated successfully without the occurrence of clogging or any other disruptions throughout. Biogas production of 0.86-0.889m 3 kg -1 VS, at OLR of 1.11-1.585kgm -3 d -1 , were obtained from vegetable market waste, which were higher than the results reported for similar substrates digested in two-phase reactors. The VS reduction was 82-86%. The two-phase anaerobic digestion system was demonstrated to be stable and suitable for the treatment of VMW fraction of MSW for energy generation. Copyright © 2016 Elsevier Ltd. All rights reserved.

[Connectionist models of social learning: a case of learning by observing a simple task].

PubMed

Paignon, A; Desrichard, O; Bollon, T

2004-03-01

This article proposes a connectionist model of the social learning theory developed by Bandura (1977). The theory posits that an individual in an interactive situation is capable of learning new behaviours merely by observing them in others. Such learning is acquired through an initial phase in which the individual memorizes what he has observed (observation phase), followed by a second phase where he puts the recorded observations to use as a guide for adjusting his own behaviour (reproduction phase). We shall refer to the two above-mentioned phases to demonstrate that it is conceivable to simulate learning by observation otherwise than through the recording of perceived information using symbolic representation. To this end we shall rely on the formalism of ecological neuron networks (Parisi, Cecconi, & Nolfi, 1990) to implement an agent provided with the major processes identified as essential to learning through observation. The connectionist model so designed shall implement an agent capable of recording perceptive information and producing motor behaviours. The learning situation we selected associates an agent demonstrating goal-achievement behaviour and an observer agent learning the same behaviour by observation. Throughout the acquisition phase, the demonstrator supervises the observer's learning process based on association between spatial information (input) and behavioural information (output). Representation thus constructed then serves as an adjustment guide during the production phase, involving production by the observer of a sequence of actions which he compares to the representation stored in distributed form as constructed through observation. An initial simulation validates model architecture by confirming the requirement for both phases identified in the literature (Bandura, 1977) to simulate learning through observation. The representation constructed over the observation phase evidences acquisition of observed behaviours, although this phase alone is not sufficient to ensure accurate reproduction and must be made functional through the production phase (Deakin & Proteau, 2000). Results obtained through a second simulation replicate those produced by Bandura & Jeffery (1973), who observed that the individual tested following the retention phase recalled recorded information better than he realized in the production phase. The outcome of a third simulation shows that, when performing the transfer task, agents performed the task all the more effectively when they were required to learn a simple path which facilitated knowledge transfer to an adjacent situation. New explanatory assumptions of the mechanics of learning through observation may be produced through OLEANNet. Thus, observed deterioration between memorization and production is caused by successive approximations which occur in the acquisition phase then in the production phase. Further, depending on the type of learning undergone by agents, use of representation as a production guide induces a more or less stringent constraint in the approximation of actual behaviour. This results, during the transfer task, in the ability to effectively generalize acquired knowledge where such knowledge is not specifically related to the task at hand. In conclusion, connectionist model architecture appears valid for modeling learning through observation as defined by Bandura (1977). However, certain limitations appear during implementation, especially in terms of the observed behaviour's availability and the planning of produced behaviours that future developments are liable to counter.

White-light diffraction phase microscopy at doubled space-bandwidth product.

PubMed

Shan, Mingguang; Kandel, Mikhail E; Majeed, Hassaan; Nastasa, Viorel; Popescu, Gabriel

2016-12-12

White light diffraction microscopy (wDPM) is a quantitative phase imaging method that benefits from both temporal and spatial phase sensitivity, granted, respectively, by the common-path geometry and white light illumination. However, like all off-axis quantitative phase imaging methods, wDPM is characterized by a reduced space-bandwidth product compared to phase shifting approaches. This happens essentially because the ultimate resolution of the image is governed by the period of the interferogram and not just the diffraction limit. As a result, off-axis techniques generates single-shot, i.e., high time-bandwidth, phase measurements, at the expense of either spatial resolution or field of view. Here, we show that combining phase-shifting and off-axis, the original space-bandwidth is preserved. Specifically, we developed phase-shifting diffraction phase microscopy with white light, in which we measure and combine two phase shifted interferograms. Due to the white light illumination, the phase images are characterized by low spatial noise, i.e., <1nm pathlength. We illustrate the operation of the instrument with test samples, blood cells, and unlabeled prostate tissue biopsy.

Vapor Phase Catalytic Ammonia Reduction

NASA Technical Reports Server (NTRS)

Flynn, Michael T.; Harper, Lynn D. (Technical Monitor)

1994-01-01

This paper discusses the development of a Vapor Phase Catalytic Ammonia Reduction (VPCAR) teststand and the results of an experimental program designed to evaluate the potential of the technology as a water purification process. In the experimental program the technology is evaluated based upon product water purity, water recovery rate, and power consumption. The experimental work demonstrates that the technology produces high purity product water and attains high water recovery rates at a relatively high specific power consumption. The experimental program was conducted in 3 phases. In phase I an Igepon(TM) soap and water mixture was used to evaluate the performance of an innovative Wiped-Film Rotating-Disk evaporator and associated demister. In phase II a phenol-water solution was used to evaluate the performance of the high temperature catalytic oxidation reactor. In phase III a urine analog was used to evaluate the performance of the combined distillation/oxidation functions of the processor.

Comparative efficacy of new commercial pediculicides against adults and eggs of Pediculus humanus capitis (head lice).

PubMed

Gallardo, Anabella; Mougabure-Cueto, Gastón; Vassena, Claudia; Picollo, María Inés; Toloza, Ariel Ceferino

2012-05-01

The use of pyrethroids to control head louse infestations have suffered considerable loss of efficacy due to the development of resistance. In the last past years, several new alternative products to synthetic pyrethroids have been developed and are sold in the Argentinean market against head lice. The present study investigated the efficacy of two new Argentinean products Nopucid Qubit® and Nopucid Bio Citrus® and its comparison with two reference products Nyda® and Hedrin®. Nopucid Qubit® is a two-phase lotion containing geraniol and citronellol (phase 1) and ciclopentaxiloxane (phase 2); while Nopucid Bio Citrus® contains dimethicone, ciclopentaxiloxane, and bergamot essential oil. These products are physically acting compounds. The sensitivity of two laboratory assays for testing insecticide activity of new formulations was also compared. Mortality (100%) of motile forms occurred after they were exposed to any product for 1 and 2 min, either by in vitro or ex vivo test. Concerning ovicidal activity, the most effective pediculicides were Nopucid Bio Citrus® and Nyda®, followed by Hedrin® and Nopucid Qubit®. The present study revealed, for the first time, the efficacy of over-the-counter commercial pediculicides available in Argentine (Nopucid Bio Citrus® and Nopucid Qubit®) on either motile stages or eggs against head lice.

The early phase of /see symbol/ production development in adult Japanese learners of English.

PubMed

Saito, Kazuya; Munro, Murray J

2014-12-01

Although previous research indicates that Japanese speakers' second language (L2) perception and production of English /see symbol/ may improve with increased L2 experience, relatively little is known about the fine phonetic details of their /see symbol/ productions, especially during the early phase of L2 speech learning. This cross-sectional study examined acoustic properties of word-initial /see symbol/ from 60 Japanese learners with a length of residence of between one month and one year in Canada. Their performance was compared to that of 15 native speakers of English and 15 low-proficiency Japanese learners of English. Formant frequencies (F2 and F3) and F1 transition durations were evaluated under three task conditions--word reading, sentence reading, and timed picture description. Learners with as little as two to three months of residence demonstrated target-like F2 frequencies. In addition, increased LOR was predictive of more target-like transition durations. Although the learners showed some improvement in F3 as a function of LOR, they did so mainly at a controlled level of speech production. The findings suggest that during the early phase of L2 segmental development, production accuracy is task-dependent and is influenced by the availability of L1 phonetic cues for redeployment in L2.

Value of Spaceborne Remotely Sensed Data Products in the Context of the Launch Phase of an On-Site Inspection

NASA Astrophysics Data System (ADS)

Labak, P.; Rowlands, A.; Malich, G.; Charlton, A.; Schultz-Fellenz, E. S.; Craven, J.

2016-12-01

The availability of data and the ability to effectively interpret those data in the context of an alleged Treaty violation are critical to operations during the launch phase of an inspection. The launch phase encompasses the time when the initial inspection plan is being developed and finalised; this document will set the scene for the inspection and will propose mission activities for the critical first three days of an inspection. While authenticated data products from the CTBT International Data Centre form the basis of the initial inspection plan, other data types, provided as national technical means, can also be used to inform the development of the initial inspection plan. In this context, remotely sensed data and derived products acquired from sensors on satellites feature prominently. Given the environmental setting, optical and/or radar sensors have the potential to provide valuable information to guide mission activities. Such data could provide more than mere backdrops to mapping products. While recognising time constraints and the difficulties associated with integrating data from disparate optical and radar sensors, this abstract uses case studies to illustrate the types of derived data products from sapecborne sensors that have the potential to inform inspectors during the preparation of the initial inspection plan.

Current status of topical antiretroviral chemoprophylaxis.

PubMed

Van Damme, Lut; Szpir, Michael

2012-11-01

Recent studies suggest that the vaginal delivery of antiretroviral (ARV) agents - such as tenofovir, dapivirine and UC781 - may be a promising way to reduce the high rates of HIV infection among women in developing countries. This review examines these developments. The Microbicide Trials Network 003 study, a large phase IIb trial, was unable to show that daily dosing with 1% tenofovir vaginal gel was effective for HIV prevention. Nevertheless, preclinical and early-phase clinical trials suggest that ARV drugs - formulated in vaginal gels, rings, films, tablets and diaphragms - could be effective for HIV chemoprophylaxis. Investigations of topical chemoprophylaxis methods have seen mixed results in the past 12-18 months. Product adherence may prove to be one of the field's greatest challenges. Phase II and III trials continue to explore different dosing strategies for topical products that contain one or more ARV agents.

Fundamentals and applications of solar energy. Part 2

NASA Astrophysics Data System (ADS)

Faraq, I. H.; Melsheimer, S. S.

Applications of techniques of chemical engineering to the development of materials, production methods, and performance optimization and evaluation of solar energy systems are discussed. Solar thermal storage systems using phase change materials, liquid phase Diels-Alder reactions, aquifers, and hydrocarbon oil were examined. Solar electric systems were explored in terms of a chlorophyll solar cell, the nonequilibrium electric field effects developed at photoelectrode/electrolyte interfaces, and designs for commercial scale processing of solar cells using continuous thin-film coating production methods. Solar coal gasification processes were considered, along with multilayer absorber coatings for solar concentrator receivers, solar thermal industrial applications, the kinetics of anaerobic digestion of crop residues to produce methane, and a procedure for developing a computer simulation of a solar cooling system.

Extractive cultivation of recombinant Escherichia coli using aqueous two-phase systems for production and separation of intracellular heat shock proteins.

PubMed

Umakoshi, H; Yano, K; Kuboi, R; Komasawa, I

1996-01-01

The extractive cultivation of recombinant Escherichia coli cells to produce, release, and separate heat shock proteins (HSPs; GroEL and GroES) using poly(ethylene glycol) (PEG)/dextran (Dex) aqueous two-phase systems was developed. The growth rate of E. coli OW10/pND5 cells in the PEG/Dex two-phase media was almost the same value as that in the control media. The addition of 0.1 M potassium phosphate salts (KPi) increased the productivity of HSPs with keeping the growth rate of E. coli cells relatively high. The partition coefficients of HSPs were improved to greater values when phosphate salts were added at a concentration of more than 0.1 M. As a result, PEG/Dex systems supplemented with 0.1 M KPi were found to be the optimized two-phase systems for the extractive cultivation of E. coli cells. In the systems, the HSPs were selectively partitioned to the top phase while cells occupied the bottom phase and the interface between the two phases. This integrated process was extended to a semicontinuous operating mode, where the top phase containing the HSPs was recovered following intermittent heating and ultrasonic irradiation. The bottom phase containing cells and cell debris was recycled together with new top phase solution to repeat production and recovery of HSPs.

Development and validation of a portable gas phase standard generation and calibration system for volatile organic compounds

Treesearch

P. Veres; J. B. Gilman; J. M. Roberts; W. C. Kuster; C. Warneke; I. R. Burling; J. de Gouw

2010-01-01

We report on the development of an accurate, portable, dynamic calibration system for volatile organic compounds (VOCs). The Mobile Organic Carbon Calibration System (MOCCS) combines the production of gas-phase VOC standards using permeation or diffusion sources with quantitative total organic carbon (TOC) conversion on a palladium surface to CO2 in the presence of...

Phase transition in tumor growth: I avascular development

NASA Astrophysics Data System (ADS)

Izquierdo-Kulich, E.; Rebelo, I.; Tejera, E.; Nieto-Villar, J. M.

2013-12-01

We propose a mechanism for avascular tumor growth based on a simple chemical network. This model presents a logistic behavior and shows a “second order” phase transition. We prove the fractal origin of the empirical logistics and Gompertz constant and its relation to mitosis and apoptosis rate. Finally, the thermodynamics framework developed demonstrates the entropy production rate as a Lyapunov function during avascular tumor growth.

DEVELOPMENT OF METHOD 535 FOR THE DETERMINATION OF CHLOROACETANILIDE AND OTHER ACETAMIDE HERBICIDE DEGRADATES IN DRINKING WATER BY SOLID PHASE EXTRACTION AND LIQUID CHROMATOGRAPHY/TANDEM MASS SPECTROMETRY

EPA Science Inventory

EPA Method 535 has been developed in order to provide a method for the analysis of "Alachlor ESA and other acetanilide degradation products" which are listed on U.S. EPA's 1998 Drinking Water Contaminant Candidate List. Method 535 uses solid phase extraction with a nonporous gr...

PREFER: a European service providing forest fire management support products

NASA Astrophysics Data System (ADS)

Eftychidis, George; Laneve, Giovanni; Ferrucci, Fabrizio; Sebastian Lopez, Ana; Lourenco, Louciano; Clandillon, Stephen; Tampellini, Lucia; Hirn, Barbara; Diagourtas, Dimitris; Leventakis, George

2015-06-01

PREFER is a Copernicus project of the EC-FP7 program which aims developing spatial information products that may support fire prevention and burned areas restoration decisions and establish a relevant web-based regional service for making these products available to fire management stakeholders. The service focuses to the Mediterranean region, where fire risk is high and damages from wildfires are quite important, and develop its products for pilot areas located in Spain, Portugal, Italy, France and Greece. PREFER aims to allow fire managers to have access to online resources, which shall facilitate fire prevention measures, fire hazard and risk assessment, estimation of fire impact and damages caused by wildfire as well as support monitoring of post-fire regeneration and vegetation recovery. It makes use of a variety of products delivered by space borne sensors and develop seasonal and daily products using multi-payload, multi-scale and multi-temporal analysis of EO data. The PREFER Service portfolio consists of two main suite of products. The first refers to mapping products for supporting decisions concerning the Preparedness/Prevention Phase (ISP Service). The service delivers Fuel, Hazard and Fire risk maps for this purpose. Furthermore the PREFER portfolio includes Post-fire vegetation recovery, burn scar maps, damage severity and 3D fire damage assessment products in order to support relative assessments required in context of the Recovery/Reconstruction Phase (ISR Service) of fire management.

Protocol Development for the NASA-JSC Lunar-Mars Life Support Test Project (LMLSTP) Phase 3 Project: A Report on Baseline Studies at KSC for Continuous Salad Production

NASA Technical Reports Server (NTRS)

Goins, G. D.; Yorio, N. C.; Vivenzio, H. R.

1998-01-01

The Phase 3 Lunar-Mars Life Support Test Project (LMLSTP) was conducted in a 20-foot chamber at Johnson Space Center. The overall objective of the Phase 3 project was to conduct a 90-day regenerative life support system test involving 4 human subjects to demonstrate an integrated biological and physicochemical life support system. A secondary objective of the Phase 3 LMLSTP was to demonstrate the ability to produce salad-type vegetable by integration of a small benchtop growth chamber located within the crew habitat area. This small chamber, commercially manufactured as the Controlled Environment Research Ecosystem (CERES 2010(TM)), functioned as a means to continuously provide fresh lettuce crops for crew members. The CERES 2010(TM) growth chamber utilized hardware components developed for effective plant biomass production in spaceflight applications. These components included: (1) LED lighting; (2) Astroculture(TM) Root Trays; and (3) Zeoponic media. In planning for the LMLSTP Phase 3, a request was put forward for KSC scientists to generate a protocol for successful continuous planting, culturing, and harvesting of the salad-crop, lettuce. By conducting baseline tests with components of the CERES 2010(TM), a protocol was developed.

Long-Term Historical Rainfall-Runoff Modeling Using High-Resolution Satellite-based Precipitation Products

NASA Astrophysics Data System (ADS)

Ashouri, H.; Nguyen, P.; Thorstensen, A. R.; Hsu, K. L.; Sorooshian, S.

2014-12-01

This study evaluates the performance of a newly developed long-term high-resolution satellite-based precipitation products, named Precipitation Estimation from Remotely Sensed Information using Artificial Neural Network - Climate Data Record (PERSIANN-CDR), in hydrological modeling. PERSIANN-CDR estimations are biased corrected using GPCP monthly climatology data. PERSIANN-CDR provides daily rainfall estimates at 0.25° x 0.25° grid boxes for 1983-2014 (delayed present). This newly released product makes it feasible to model the streamflow over the past 30 years. Three test basins from the Distributed Hydrologic Model Intercomparison Project - Phase 2 (DMIP 2) are chosen. Comparing with other satellite products, the Version 7 TRMM Multi-satellite Precipitation Analysis (TMPA) product is used. Stage IV radar data is used as a reference data for evaluating the PERSIANN-CDR and TMPA precipitation data. All products are scaled to 0.25° and daily spatiotemporal resolution. The study is performed in two phases. In the first phase, the 2003-2011 period where all the products are available is chosen. Precipitation evaluation results, presented on Taylor Diagrams, show that TMPA and PERSIANN-CDR have close performances. The National Weather Service (NWS) Office of Hydrologic Development (OHD) Hydrology Laboratory-Research Distributed Hydrologic Model (HL-RDHM) is then forced with the PERSIANN-CDR and the TMPA precipitation products, as well as the stage IV radar data. USGS Streamflow observations at the outlet of the basins are used as the reference streamflow data. The results show that in general, in all the three DMIP 2 basins the simulated hydrographs forced with PERSIANN-CDR and TMPA show good agreement, as the statistical measures such as root mean square error, bias, and correlation coefficient are close. In addition, with respect to the streamflow peaks, PERSIANN-CDR shows better performance than Stage IV radar data in capturing the extreme streamflow magnitudes. Based on the results from the first phase of the study and given the fact that PERSIANN-CDR covers the 1983-2014, in the second phase of the study we model the streamflow for the period of 1983-2014. The results will be presented in the meeting.

Crew interface specifications development functions, phase 3A

NASA Technical Reports Server (NTRS)

Carl, J. G.

1973-01-01

The findings and data products developed during the crew interface specification study for inflight maintenance and stowage functions are presented. Guidelines are provided for improving the present progress of defining, controlling, and managing the flight crew requirements. The following data products were developed: (1) description of inflight maintenance management process, (2) specifications for inflight maintenance management requirements, and (3) suggested inflight maintenance data processing reports for logistics management.

The Framework for Life Cycle Cost Management,

DTIC Science & Technology

1982-01-01

in the early phases of system development before full- scale development and initial production, O&S cost projections are too un- certain to...Ensure that each increment of cost and schedule investment in R&M contributes significantly to the above objectives. DoDD 5000.40, Reliability and...Major systems are characterized by large investments of time and resources in the uncertain periods of development, production, and deployment and in

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dafler, J.R.; Sinnott, J.; Novil, M.

The first phase of a study to identify candidate processes and products suitable for future exploitation using high-temperature solar energy is presented. This phase has been principally analytical, consisting of techno-economic studies, thermodynamic assessments of chemical reactions and processes, and the determination of market potentials for major chemical commodities that use significant amounts of fossil resources today. The objective was to identify energy-intensive processes that would be suitable for the production of chemicals and fuels using solar energy process heat. Of particular importance was the comparison of relative costs and energy requirements for the selected solar product versus costs formore » the product derived from conventional processing. The assessment methodology used a systems analytical approach to identify processes and products having the greatest potential for solar energy-thermal processing. This approach was used to establish the basis for work to be carried out in subsequent phases of development. It has been the intent of the program to divide the analysis and process identification into the following three distinct areas: (1) process selection, (2) process evaluation, and (3) ranking of processes. Four conventional processes were selected for assessment namely, methanol synthesis, styrene monomer production, vinyl chloride monomer production, and terephthalic acid production.« less

Instructional Media Production for Early Childhood Education: A. B. C. Jig-Saw Puzzle, a Model

ERIC Educational Resources Information Center

Yusuf, Mudashiru Olalere; Olanrewaju, Olatayo Solomon; Soetan, Aderonke K.

2015-01-01

In this paper, a. b. c. jig-saw puzzle was produced for early childhood education using local materials. This study was a production based type of research, to serve as a supplemental or total learning resource. Its production followed four phases of development referred to as information, design, production and evaluation. The storyboard cards,…

Label-free proteome profiling reveals developmental-dependent patterns in young barley grains.

PubMed

Kaspar-Schoenefeld, Stephanie; Merx, Kathleen; Jozefowicz, Anna Maria; Hartmann, Anja; Seiffert, Udo; Weschke, Winfriede; Matros, Andrea; Mock, Hans-Peter

2016-06-30

Due to its importance as a cereal crop worldwide, high interest in the determination of factors influencing barley grain quality exists. This study focusses on the elucidation of protein networks affecting early grain developmental processes. NanoLC-based separation coupled to label-free MS detection was applied to gain insights into biochemical processes during five different grain developmental phases (pre-storage until storage phase, 3days to 16days after flowering). Multivariate statistics revealed two distinct developmental patterns during the analysed grain developmental phases: proteins showed either highest abundance in the middle phase of development - in the transition phase - or at later developmental stages - within the storage phase. Verification of developmental patterns observed by proteomic analysis was done by applying hypothesis-driven approaches, namely Western Blot analysis and enzyme assays. High general metabolic activity of the grain with regard to protein synthesis, cell cycle regulation, defence against oxidative stress, and energy production via photosynthesis was observed in the transition phase. Proteins upregulated in the storage phase are related towards storage protein accumulation, and interestingly to the defence of storage reserves against pathogens. A mixed regulatory pattern for most enzymes detected in our study points to regulatory mechanisms at the level of protein isoforms. In-depth understanding of early grain developmental processes of cereal caryopses is of high importance as they influence final grain weight and quality. Our knowledge about these processes is still limited, especially on proteome level. To identify key mechanisms in early barley grain development, a label-free data-independent proteomics acquisition approach has been applied. Our data clearly show, that proteins either exhibit highest expression during cellularization and the switch to the storage phase (transition phase, 5-7 DAF), or during storage product accumulation (10-16 DAF). The results highlight versatile cellular metabolic activity in the transition phase and strong convergence towards storage product accumulation in the storage phase. Notably, both phases are characterized by particular protective mechanism, such as scavenging of oxidative stress and defence against pathogens, during the transition and the storage phase, respectively. Copyright © 2016 Elsevier B.V. All rights reserved.

Making America Work. Productive People, Productive Policies. Follow-up Report 1988.

ERIC Educational Resources Information Center

National Governors' Association, Washington, DC.

The National Governors' Association's Making America Work initiative had a dual focus. Five task forces spent a year developing action agendas to address five barriers to self-sufficiency and productivity: teenage pregnancy, adult illiteracy, welfare dependency, alcohol and drug abuse, and dropping out of school. The second phase of the initiative…

An approach for upgrading biomass and pyrolysis product quality using a combination of aqueous phase bio-oil washing and torrefaction pretreatment.

PubMed

Chen, Dengyu; Cen, Kehui; Jing, Xichun; Gao, Jinghui; Li, Chen; Ma, Zhongqing

2017-06-01

Bio-oil undergoes phase separation because of poor stability. Practical application of aqueous phase bio-oil is challenging. In this study, a novel approach that combines aqueous phase bio-oil washing and torrefaction pretreatment was used to upgrade the biomass and pyrolysis product quality. The effects of individual and combined pretreatments on cotton stalk pyrolysis were studied using TG-FTIR and a fixed bed reactor. The results showed that the aqueous phase bio-oil washing pretreatment removed metals and resolved the two pyrolysis peaks in the DTG curve. Importantly, it increased the bio-oil yield and improved the pyrolysis product quality. For example, the water and acid content of bio-oil decreased significantly along with an increase in phenol formation, and the heating value of non-condensable gases improved, and these were more pronounced when combined with torrefaction pretreatment. Therefore, the combined pretreatment is a promising method, which would contribute to the development of polygeneration pyrolysis technology. Copyright © 2017 Elsevier Ltd. All rights reserved.

Gas and Particle Oxidation Products from Ozone Aging of Airborne Diesel Particles

NASA Astrophysics Data System (ADS)

Holmen, B. A.; Chen, Z.

2005-12-01

Diesel exhaust emissions contain fine particulate matter (PM2.5) composed of carbon-based particles with adsorbed compounds, including water soluble and insoluble substances. Many nonpolar organic compounds associated with diesel particulate matter (DPM) are known to be mutagenic and carcinogenic. In the presence of ozone, these DPM compounds can be transformed into polar species that are more toxic and poorly characterized. Understanding the gas and particle reaction products from DPM aging in the presence of tropospheric ozone is important for air quality, climate change and aerosol health effects. Aging experiments were conducted in a flow reactor to identify gas and particle-phase reaction products of DPM exposed to ambient levels of ozone. Diesel bus exhaust particles were collected on filters and then exposed to 0.1 - 0.5 ppm O3 for 0 to 72 h. Gaseous polar organic products formed during the aging experiments were collected on Tenax TA adsorbent coated with PFBHA derivatization agent. A thermal desorption gas chromatography mass spectrometry (TD/GC/MS) method was developed to determine gas-phase and particle-phase organic compounds. PFBHA and BSTFA derivatization agents converted polar species into less polar analogues prior to analysis. Preliminary results indicate that DPM hydrocarbons react with O3 to form many gas-phase polar products containing C=O (carbonyl) and COOH (carboxy) functional groups. Particle-phase PAH and alkane concentrations decreased significantly depending on time of exposure.

Phased Array Radar Network Experiment for Severe Weather

NASA Astrophysics Data System (ADS)

Ushio, T.; Kikuchi, H.; Mega, T.; Yoshikawa, E.; Mizutani, F.; Takahashi, N.

2017-12-01

Phased Array Weather Radar (PAWR) was firstly developed in 2012 by Osaka University and Toshiba under a grant of NICT using the Digital Beamforming Technique, and showed a impressive thunderstorm behavior with 30 second resolution. After that development, second PAWR was installed in Kobe city about 60 km away from the first PAWR site, and Tokyo Metropolitan University, Osaka Univeristy, Toshiba and the Osaka Local Government started a new project to develop the Osaka Urban Demonstration Network. The main sensor of the Osaka Network is a 2-node Phased Array Radar Network and lightning location system. Data products that are created both in local high performance computer and Toshiba Computer Cloud, include single and multi-radar data, vector wind, quantitative precipitation estimation, VIL, nowcasting, lightning location and analysis. Each radar node is calibarated by the baloon measurement and through the comparison with the GPM (Global Precipitation Measurement)/ DPR (Dual Frequency Space borne Radar) within 1 dB. The attenuated radar reflectivities obtained by the Phased Array Radar Network at X band are corrected based on the bayesian scheme proposed in Shimamura et al. [2016]. The obtained high resolution (every 30 seconds/ 100 elevation angles) 3D reflectivity and rain rate fields are used to nowcast the surface rain rate up to 30 minutes ahead. These new products are transferred to Osaka Local Government in operational mode and evaluated by several section in Osaka Prefecture. Furthermore, a new Phased Array Radar with polarimetric function has been developed in 2017, and will be operated in the fiscal year of 2017. In this presentation, Phased Array Radar, network architecuture, processing algorithm, evalution of the social experiment and first Multi-Prameter Phased Array Radar experiment are presented.

Development and Implementation of High-Throughput SNP Genotyping in Barley

USDA-ARS?s Scientific Manuscript database

Approximately 22,000 SNPs were identified from barley ESTs and sequenced amplicons; 4,596 of them were tested for performance in three pilot phase Illumina GoldenGate assays. Pilot phase data from three barley doubled haploid mapping populations supported the production of an initial consensus map, ...

Forecasting production in Liquid Rich Shale plays

NASA Astrophysics Data System (ADS)

Nikfarman, Hanieh

Production from Liquid Rich Shale (LRS) reservoirs is taking center stage in the exploration and production of unconventional reservoirs. Production from the low and ultra-low permeability LRS plays is possible only through multi-fractured horizontal wells (MFHW's). There is no existing workflow that is applicable to forecasting multi-phase production from MFHW's in LRS plays. This project presents a practical and rigorous workflow for forecasting multiphase production from MFHW's in LRS reservoirs. There has been much effort in developing workflows and methodology for forecasting in tight/shale plays in recent years. The existing workflows, however, are applicable only to single phase flow, and are primarily used in shale gas plays. These methodologies do not apply to the multi-phase flow that is inevitable in LRS plays. To account for complexities of multiphase flow in MFHW's the only available technique is dynamic modeling in compositional numerical simulators. These are time consuming and not practical when it comes to forecasting production and estimating reserves for a large number of producers. A workflow was developed, and validated by compositional numerical simulation. The workflow honors physics of flow, and is sufficiently accurate while practical so that an analyst can readily apply it to forecast production and estimate reserves in a large number of producers in a short period of time. To simplify the complex multiphase flow in MFHW, the workflow divides production periods into an initial period where large production and pressure declines are expected, and the subsequent period where production decline may converge into a common trend for a number of producers across an area of interest in the field. Initial period assumes the production is dominated by single-phase flow of oil and uses the tri-linear flow model of Erdal Ozkan to estimate the production history. Commercial software readily available can simulate flow and forecast production in this period. In the subsequent Period, dimensionless rate and dimensionless time functions are introduced that help identify transition from initial period into subsequent period. The production trends in terms of the dimensionless parameters converge for a range of rock permeability and stimulation intensity. This helps forecast production beyond transition to the end of life of well. This workflow is applicable to single fluid system.

Propulsion and Power Rapid Response Research and Development (R&D) Support. Task Order 0004: Advanced Propulsion Fuels R&D, Subtask: Optimization of Lipid Production and Processing of Microalgae for the Development of Biofuels

DTIC Science & Technology

2013-02-01

Purified cultures are tested for optimized production under heterotrophic conditions with several organic carbon sources like beet and sorghum juice using ...Moreover, AFRL support sponsored the Master’s in Chemical Engineering project titled “Cost Analysis Of Local Bio- Products Processing Plant Using ...unlimited. 2.5 Screening for High Lipid Production Mutants Procedure: A selection of 84 single colony cultures was analyzed in this phase using the

DOE Office of Scientific and Technical Information (OSTI.GOV)

Underwood, R.P.

As part of the DOE-sponsored contract Synthesis of Dimethyl Ether and Alternative Fuels in the Liquid Phase from Coal-Derived Syngas'' experimental evaluations of the one-step synthesis of alternative fuels were carried out. The objective of this work was to develop novel processes for converting coal-derived syngas to fuels or fuel additives. Building on a technology base acquired during the development of the Liquid Phase Methanol (LPMEOH) process, this work focused on the development of slurry reactor based processes. The experimental investigations, which involved bench-scale reactor studies, focused primarily on three areas: (1) One-step, slurry-phase syngas conversion to hydrocarbons or methanol/hydrocarbonmore » mixtures using a mixture of methanol synthesis catalyst and methanol conversion catalyst in the same slurry reactor. (2) Slurry-phase conversion of syngas to mixed alcohols using various catalysts. (3) One-step, slurry-phase syngas conversion to mixed ethers using a mixture of mixed alcohols synthesis catalyst and dehydration catalyst in the same slurry reactor. The experimental results indicate that, of the three types of processes investigated, slurry phase conversion of syngas to mixed alcohols shows the most promise for further process development. Evaluations of various mixed alcohols catalysts show that a cesium-promoted Cu/ZnO/Al[sub 2]O[sub 3] methanol synthesis catalyst, developed in Air Products' laboratories, has the highest performance in terms of rate and selectivity for C[sub 2+]-alcohols. In fact, once-through conversion at industrially practical reaction conditions yielded a mixed alcohols product potentially suitable for direct gasoline blending. Moreover, an additional attractive aspect of this catalyst is its high selectivity for branched alcohols, potential precursors to iso-olefins for use in etherification.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Underwood, R.P.

As part of the DOE-sponsored contract ``Synthesis of Dimethyl Ether and Alternative Fuels in the Liquid Phase from Coal-Derived Syngas`` experimental evaluations of the one-step synthesis of alternative fuels were carried out. The objective of this work was to develop novel processes for converting coal-derived syngas to fuels or fuel additives. Building on a technology base acquired during the development of the Liquid Phase Methanol (LPMEOH) process, this work focused on the development of slurry reactor based processes. The experimental investigations, which involved bench-scale reactor studies, focused primarily on three areas: (1) One-step, slurry-phase syngas conversion to hydrocarbons or methanol/hydrocarbonmore » mixtures using a mixture of methanol synthesis catalyst and methanol conversion catalyst in the same slurry reactor. (2) Slurry-phase conversion of syngas to mixed alcohols using various catalysts. (3) One-step, slurry-phase syngas conversion to mixed ethers using a mixture of mixed alcohols synthesis catalyst and dehydration catalyst in the same slurry reactor. The experimental results indicate that, of the three types of processes investigated, slurry phase conversion of syngas to mixed alcohols shows the most promise for further process development. Evaluations of various mixed alcohols catalysts show that a cesium-promoted Cu/ZnO/Al{sub 2}O{sub 3} methanol synthesis catalyst, developed in Air Products` laboratories, has the highest performance in terms of rate and selectivity for C{sub 2+}-alcohols. In fact, once-through conversion at industrially practical reaction conditions yielded a mixed alcohols product potentially suitable for direct gasoline blending. Moreover, an additional attractive aspect of this catalyst is its high selectivity for branched alcohols, potential precursors to iso-olefins for use in etherification.« less

Drilling and Production Activity Related to Unconventional Gas Development and Severity of Preterm Birth.

PubMed

Walker Whitworth, Kristina; Kaye Marshall, Amanda; Symanski, Elaine

2018-03-20

Studies of unconventional gas development (UGD) and preterm birth (PTB) have not presented risk estimates by well development phase or trimester. We examined phase and trimester-specific associations between UGD activity and PTB. We conducted a case-control study of women with singleton births in the Barnett Shale area, Texas, from 30 November 2010 to 29 November 2012. We individually age- and race/ethnicity-matched five controls to each PTB case ( n =13,328) and truncated controls' time at risk according to the matched case's gestational age. We created phase-specific UGD-activity metrics: a ) inverse squared distance-weighted (IDW) count of wells in the drilling phase ≤0.5 mi (804.7 meters) of the residence and b ) IDW sum of natural gas produced ≤0.5 mi of the residence. We also constructed trimester- and gestation-specific metrics. Metrics were categorized as follows: zero wells (reference), first, second, third tertiles of UGD activity. Analyses were repeated by PTB severity: extreme, very, and moderate (<28, 28 to<32, and 32 to<37 completed weeks). Data were analyzed using conditional logistic regression. We found increased odds of PTB in the third tertile of the UGD drilling {odds ratio (OR)=1.20 [95% confidence interval (CI): 1.06, 1.37]} and UGD-production [OR=1.15 (1.05, 1.26)] metrics. Among women in the third tertile of UGD-production, associations were strongest in trimesters one [OR=1.18 (1.02, 1.37)] and two [OR=1.14 (0.99, 1.31). The greatest risk was observed for extremely PTB [third tertile ORs: UGD drilling, 2.00 (1.23, 3.24); UGD production, 1.53 (1.03-2.27)]. We found evidence of differences in phase- and trimester-specific associations of UGD and PTB and indication of particular risk associated with extremely preterm birth. Future studies should focus on quantifying specific chemical and nonchemical stressors associated with UGD. https://doi.org/10.1289/EHP2622.

A theoretical evaluation of aluminum gel propellant two-phase flow losses on vehicle performance

NASA Technical Reports Server (NTRS)

Mueller, Donn C.; Turns, Stephen R.

1993-01-01

A one-dimensional model of a hydrocarbon/Al/O2(gaseous) fueled rocket combustion chamber was developed to study secondary atomization effects on propellant combustion. This chamber model was coupled with a two dimensional, two-phase flow nozzle code to estimate the two-phase flow losses associated with solid combustion products. Results indicate that moderate secondary atomization significantly reduces propellant burnout distance and Al2O3 particle size; however, secondary atomization provides only moderate decreases in two-phase flow induced I(sub sp) losses. Despite these two-phase flow losses, a simple mission study indicates that aluminum gel propellants may permit a greater maximum payload than the hydrocarbon/O2 bi-propellant combination for a vehicle of fixed propellant volume. Secondary atomization was also found to reduce radiation losses from the solid combustion products to the chamber walls, primarily through reductions in propellant burnout distance.

Surface based factory for the production of life support and technology support products

NASA Technical Reports Server (NTRS)

1987-01-01

The presence of a manned space colony on Mars may be expected to involve three phases in the utilization of planetary resources: (1) survival phase in which air, water, and food are produced, (2) self sufficiency phase in which chemicals, fuels, pharmaceuticals, polymers, and metals are produced, and (3) export to earth of materials and technology 1 phase in which the unique advantage of the extraterrestrial environment is fully exploited. The Advanced Design Project is administered as an interdisciplinary effort involving students and faculty throughout the College of Engineering. Senior students from Chemical, Civil, Electrical, and Mechanical Engineering are participating as a team. Multi discipline interfacing and coordination are stressed throughout the project. An interdisciplinary senior design course was developed and offered in the Spring of 1987. The first task of the survival phase is that of providing a supply of water and air adequate to support a ten person colony. The project has been divided into three subgroups: (1) design of a manufacturing and storage facility for air, (2) search and drill for water or water-bearing materials, and (3) retrieve, purify, and store potable water. The conceptual design phase has been completed and the project is being documented. The second task of the survival phase is that of providing a replenish able food supply. This task has two requirements: producing a supply of protein and providing an environment for growing plants for food. For the first requirement, we considered the design of a bioreactor system capable of growing beef cells for protein production. For the second, a design must be developed for a manufacturing system to produce materials needed to build a greenhouse farm.

GMP production and characterization of leucine zipper-tagged tumor necrosis factor-related apoptosis-inducing ligand (LZ-TRAIL) for phase I clinical trial.

PubMed

Jiang, Jing; Liu, Xiaobin; Deng, Leixiu; Zhang, Peipei; Wang, Guangjun; Wang, Shifu; Liu, Honghao; Su, Yunpeng

2014-10-05

Tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) exhibits potent antitumor activity in a wide range of cancers without deleterious side effects on normal tissues. Several TRAIL derivatives have been developed to improve its pharmacokinetics and therapeutic effects through strategies such as adding a leucine zipper to increase the circulation half-life. To obtain clinical grade LZ-TRAIL for phase I clinical trial, a single batch of 30 L bioreactor culture was performed using the Escherichia coli BL21 (DE3) strain expressing the recombinant LZ-TRAIL. A robust LZ-TRAIL production fermentation process was developed, which could be scaled up from 5L to 50 L, and had a titer of approximately 1.4 g/l. A four-step purification strategy was carried out to obtain a final product with over 95% purity and 45% yield. The final material was filter sterilized, aseptically vialed, and stored at 4°C, and comprehensively characterized using multiple assays (vialed product was sterile, purity was 95%, aggregates were <5%, potency revealed IC50 of 9 nM on MDA-MB-231 cells, and the endotoxin level was <0.25 U/mg). The purity, composition, and functional activities of the molecule were confirmed. in vivo investigations indicated that LZ-TRAIL has better antitumor potency in three Xenograft tumor models compared to TRAIL (95-281). LZ-TRAIL also showed improved pharmacokinetic and safety profiles in cynomolgus monkeys without abnormalities associated with drug exposure. In conclusion, the scalable synthesis of LZ-TRAIL is useful for production of phase I clinical trial material. These preclinical investigations warrant further clinical development of this product for cancer therapy. Copyright © 2014. Published by Elsevier B.V.

National Institutes of Health-Sponsored Clinical Islet Transplantation Consortium Phase 3 Trial: Manufacture of a Complex Cellular Product at Eight Processing Facilities.

PubMed

Ricordi, Camillo; Goldstein, Julia S; Balamurugan, A N; Szot, Gregory L; Kin, Tatsuya; Liu, Chengyang; Czarniecki, Christine W; Barbaro, Barbara; Bridges, Nancy D; Cano, Jose; Clarke, William R; Eggerman, Thomas L; Hunsicker, Lawrence G; Kaufman, Dixon B; Khan, Aisha; Lafontant, David-Erick; Linetsky, Elina; Luo, Xunrong; Markmann, James F; Naji, Ali; Korsgren, Olle; Oberholzer, Jose; Turgeon, Nicole A; Brandhorst, Daniel; Chen, Xiaojuan; Friberg, Andrew S; Lei, Ji; Wang, Ling-Jia; Wilhelm, Joshua J; Willits, Jamie; Zhang, Xiaomin; Hering, Bernhard J; Posselt, Andrew M; Stock, Peter G; Shapiro, A M James; Chen, Xiaojuan

2016-11-01

Eight manufacturing facilities participating in the National Institutes of Health-sponsored Clinical Islet Transplantation (CIT) Consortium jointly developed and implemented a harmonized process for the manufacture of allogeneic purified human pancreatic islet (PHPI) product evaluated in a phase 3 trial in subjects with type 1 diabetes. Manufacturing was controlled by a common master production batch record, standard operating procedures that included acceptance criteria for deceased donor organ pancreata and critical raw materials, PHPI product specifications, certificate of analysis, and test methods. The process was compliant with Current Good Manufacturing Practices and Current Good Tissue Practices. This report describes the manufacturing process for 75 PHPI clinical lots and summarizes the results, including lot release. The results demonstrate the feasibility of implementing a harmonized process at multiple facilities for the manufacture of a complex cellular product. The quality systems and regulatory and operational strategies developed by the CIT Consortium yielded product lots that met the prespecified characteristics of safety, purity, potency, and identity and were successfully transplanted into 48 subjects. No adverse events attributable to the product and no cases of primary nonfunction were observed. © 2016 by the American Diabetes Association.

National Institutes of Health–Sponsored Clinical Islet Transplantation Consortium Phase 3 Trial: Manufacture of a Complex Cellular Product at Eight Processing Facilities

PubMed Central

Balamurugan, A.N.; Szot, Gregory L.; Kin, Tatsuya; Liu, Chengyang; Czarniecki, Christine W.; Barbaro, Barbara; Bridges, Nancy D.; Cano, Jose; Clarke, William R.; Eggerman, Thomas L.; Hunsicker, Lawrence G.; Kaufman, Dixon B.; Khan, Aisha; Lafontant, David-Erick; Linetsky, Elina; Luo, Xunrong; Markmann, James F.; Naji, Ali; Korsgren, Olle; Oberholzer, Jose; Turgeon, Nicole A.; Brandhorst, Daniel; Chen, Xiaojuan; Friberg, Andrew S.; Lei, Ji; Wang, Ling-jia; Wilhelm, Joshua J.; Willits, Jamie; Zhang, Xiaomin; Hering, Bernhard J.; Posselt, Andrew M.; Stock, Peter G.; Shapiro, A.M. James

2016-01-01

Eight manufacturing facilities participating in the National Institutes of Health–sponsored Clinical Islet Transplantation (CIT) Consortium jointly developed and implemented a harmonized process for the manufacture of allogeneic purified human pancreatic islet (PHPI) product evaluated in a phase 3 trial in subjects with type 1 diabetes. Manufacturing was controlled by a common master production batch record, standard operating procedures that included acceptance criteria for deceased donor organ pancreata and critical raw materials, PHPI product specifications, certificate of analysis, and test methods. The process was compliant with Current Good Manufacturing Practices and Current Good Tissue Practices. This report describes the manufacturing process for 75 PHPI clinical lots and summarizes the results, including lot release. The results demonstrate the feasibility of implementing a harmonized process at multiple facilities for the manufacture of a complex cellular product. The quality systems and regulatory and operational strategies developed by the CIT Consortium yielded product lots that met the prespecified characteristics of safety, purity, potency, and identity and were successfully transplanted into 48 subjects. No adverse events attributable to the product and no cases of primary nonfunction were observed. PMID:27465220

Lunar synchronization of testicular development and steroidogenesis in rabbitfish.

PubMed

Rahman, M S; Takemura, A; Takano, K

2001-06-01

Lunar synchronization of testicular development in the golden rabbitfish, Siganus guttatus, was assessed by measuring changes in sperm motility and conditions in the seminal plasma, and by in vitro production of steroid hormones in testicular fragments and sperm preparations. The duration and percentage of sperm motility was low 1 week before spawning (the new moon), but increased significantly on the day of spawning (the first lunar quarter). During the first lunar quarter, the osmolality decreased, but Ca(2+) concentration increased in the seminal plasma. These results suggest that spermiation occurs rapidly towards the specific lunar phase. Testicular fragments and sperm preparations were incubated with human chorionic gonadotropin (hCG) and two precursor steroid hormones, 17alpha-hydroxyprogesterone (17alpha-OHP) and testosterone (T), during the two lunar phases. The production of 11-ketotestosterone (11-KT) increased significantly when the testicular fragments were incubated with hCG at the first lunar quarter, while incubation of sperm preparations with 17alpha-OHP during the same moon phase resulted in a significant increase in 17alpha,20beta-dihydroxy-4-pregnen-3-one (DHP) production in the medium. These results suggest that 11-KT is produced in the somatic cells of the testis under the influence of gonadotropin, and that sperm can convert 17alpha-OHP to DHP. Additionally, steroidogenic activity was considered to increase toward the specific lunar phase. The synchronous increase in testicular activity supports the hypothesis that lunar periodicity is a major factor for the testicular development of S. guttatus.

Spray Forming Aluminum - Final Report (Phase II)

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. D. Leon

1999-07-08

The U.S. Department of Energy - Office of Industrial Technology (DOE) has an objective to increase energy efficient and enhance competitiveness of American metals industries. To support this objective, ALCOA Inc. entered into a cooperative program to develop spray forming technology for aluminum. This Phase II of the DOE Spray Forming Program would translate bench scale spray forming technology into a cost effective world class process for commercialization. Developments under DOE Cooperative Agreement No. DE-FC07-94ID13238 occurred during two time periods due to budgetary constraints; April 1994 through September 1996 and October 1997 and December 1998. During these periods, ALCOA Incmore » developed a linear spray forming nozzle and specific support processes capable of scale-up for commercial production of aluminum sheet alloy products. Emphasis was given to alloys 3003 and 6111, both being commercially significant alloys used in the automotive industry. The report reviews research performed in the following areas: Nozzel Development, Fabrication, Deposition, Metal Characterization, Computer Simulation and Economics. With the formation of a Holding Company, all intellectual property developed in Phases I and II of the Project have been documented under separate cover for licensing to domestic producers.« less

Silica phase changes: Diagenetic agent for oil entrapment, Lost Hills field, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Julander, D.R.; Szymanski, D.L.

1991-02-01

The siliceous shales of the Monterey Group are the primary development target at Lost Hills. Silica phase changes have influenced the distribution and entrapment of hydrocarbons. With increasing temperature, opal A phase diatomite is converted to opal CT and finally quartz phase rock. All phases are low in permeability. The opal A diatomite is characteristically high in oil saturation and productive saturation. Productivity from this phase is dependent on structural position and fieldwide variations in oil viscosity and biodegradation. The deeper chert reservoir coincides with the opal CT to quartz phase transition. Porosity is again reduced in this transition, butmore » saturations in the quartz phase rocks increase. Tests in the chert reservoir indicate a single, low-permeability system, suggesting the importance of matric contribution. resistivity and porosity in the diatomite, and resistivity and velocity in the chert, are the physical properties which best reflect saturation. Methods exploiting these properties (FMS, BHTV, borehole, and surface shear wave studies) should be helpful in further characterizing the reservoirs and identifying future pay.« less

Discovery and Development of Natural Product-derived Chemotherapeutic Agents Based on a Medicinal Chemistry Approach⊥†

PubMed Central

Lee, Kuo-Hsiung

2010-01-01

Medicinal plants have long been an excellent source of pharmaceutical agents. Accordingly, the long term objectives of the author's research program are to discover and design new chemotherapeutic agents based on plant-derived compound leads by using a medicinal chemistry approach, which is a combination of chemistry and biology. Different examples of promising bioactive natural products and their synthetic analogs, including sesquiterpene lactones, quassinoids, naphthoquinones, phenylquinolones, dithiophenediones, neo-tanshinlactone, tylophorine, suksdorfin, DCK, and DCP, will be presented with respect to their discovery and preclinical development as potential clinical trial candidates. Research approaches include bioactivity- or mechanism of action-directed isolation and characterization of active compounds, rational drug design-based modification and analog synthesis, as well as structure-activity relationship and mechanism of action studies. Current clinical trials agents discovered by the Natural Products Research Laboratories, University of North Carolina, include bevirimat (dimethyl succinyl betulinic acid), which is now in Phase IIb trials for treating AIDS. Bevirimat is also the first in a new class of HIV drug candidates called “maturation inhibitors”. In addition, an etoposide analog, GL-331, progressed to anticancer Phase II clinical trials, and the curcumin analog JC-9 is in Phase II clinical trials for treating acne and in development for trials against prostate cancer. The discovery and development of these clinical trials candidates will also be discussed. PMID:20187635

Development and application of a biorelevant dissolution method using USP apparatus 4 in early phase formulation development.

PubMed

Fang, Jiang B; Robertson, Vivian K; Rawat, Archana; Flick, Tawnya; Tang, Zhe J; Cauchon, Nina S; McElvain, James S

2010-10-04

Dissolution testing is frequently used to determine the rate and extent at which a drug is released from a dosage form, and it plays many important roles throughout drug product development. However, the traditional dissolution approach often emphasizes its application in quality control testing and usually strives to obtain 100% drug release. As a result, dissolution methods are not necessarily biorelevant and meaningful application of traditional dissolution methods in the early phases of drug product development can be very limited. This article will describe the development of a biorelevant in vitro dissolution method using USP apparatus 4, biorelevant media, and real-time online UV analysis. Several case studies in the areas of formulation selection, lot-to-lot variability, and food effect will be presented to demonstrate the application of this method in early phase formulation development. This biorelevant dissolution method using USP apparatus 4 provides a valuable tool to predict certain aspects of the in vivo drug release. It can be used to facilitate the formulation development/selection for pharmacokinetic (PK) and clinical studies. It may also potentially be used to minimize the number of PK studies, and to aid in the design of more efficient PK and clinical studies.

Private investment in AIDS vaccine development: obstacles and solutions.

PubMed

Batson, A; Ainsworth, M

2001-01-01

The development of vaccines for the prevention of AIDS, malaria, tuberculosis, and other diseases requires both public and private investment. Private investment, however, has been far lower than might have been hoped, given the massive human toll of these diseases, particularly in the poorest countries. With a view to understanding this situation and exploring potential solutions, the World Bank AIDS Vaccine Task Force commissioned a study on the perspectives of the biotechnology, vaccine, and pharmaceutical industries regarding investment in research and development work on an AIDS vaccine. It was found that different obstacles to the development of an AIDS vaccine arose during the product development cycle. During the earlier phases, before obtaining proof of product, the principal barriers were scientific. The lack of consensus on which approach was likely to be effective increased uncertainty and the risks associated with investing in expensive clinical trials. The later phases, which involved adapting, testing, and scaling up production for different populations, were most influenced by market considerations. In order to raise the levels of private research and development in an AIDS vaccine there will probably have to be a combination of push strategies, which reduce the cost and scientific risk of investment, and pull strategies, which guarantee a market.

New approaches to the measurement of chlorophyll, related pigments and productivity in the sea

NASA Technical Reports Server (NTRS)

Booth, C. R.; Keifer, D. A.

1989-01-01

In the 1984 SBIR Call for Proposals, NASA solicited new methods to measure primary production and chlorophyll in the ocean. Biospherical Instruments Inc. responded to this call with a proposal first to study a variety of approaches to this problem. A second phase of research was then funded to pursue instrumentation to measure the sunlight stimulated naturally occurring fluorescence of chlorophyll in marine phytoplankton. The monitoring of global productivity, global fisheries resources, application of above surface-to-underwater optical communications systems, submarine detection applications, correlation, and calibration of remote sensing systems are but some of the reasons for developing inexpensive sensors to measure chlorophyll and productivity. Normally, productivity measurements are manpower and cost intensive and, with the exception of a very few expensive multiship research experiments, provide no contemporaneous data. We feel that the patented, simple sensors that we have designed will provide a cost effective method for large scale, synoptic, optical measurements in the ocean. This document is the final project report for a NASA sponsored SBIR Phase 2 effort to develop new methods for the measurements of primary production in the ocean. This project has been successfully completed, a U.S. patent was issued covering the methodology and sensors, and the first production run of instrumentation developed under this contract has sold out and been delivered.

Plant-made vaccine antigens and biopharmaceuticals

PubMed Central

Daniell, Henry; Singh, Nameirakpam D.; Mason, Hugh; Streatfield, Stephen J.

2009-01-01

Plant cells are ideal bioreactors for the production and oral delivery of vaccines and biopharmaceuticals, eliminating the need for expensive fermentation, purification, cold storage, transportation and sterile delivery. Plant-made vaccines have been developed for two decades but none has advanced beyond Phase I. However, two plant-made biopharmaceuticals are now advancing through Phase II and Phase III human clinical trials. In this review, we evaluate the advantages and disadvantages of different plant expression systems (stable nuclear and chloroplast or transient viral) and their current limitations or challenges. We provide suggestions for advancing this valuable concept for clinical applications and conclude that greater research emphasis is needed on large scale production, purification, functional characterization, oral delivery and preclinical evaluation. PMID:19836291

Successful development of recombinant DNA-derived pharmaceuticals.

PubMed

Werner, R G; Pommer, C H

1990-11-01

Successful development of recombinant DNA-derived pharmaceuticals, a new class of therapeutic agents, is determined by a variety of factors affecting the selection and positioning of the compound under development. For an efficient development it is of utmost importance that the mechanism of action of the compound selected be understood on a molecular level. The compound's potential therapeutical profile and a strong patent position are key positioning considerations, as well as vital elements in shortening the development phase and protecting innovation. Installation of an interdisciplinary project management team, along with a clear definition of team members' responsibilities, is required to avoid delays and improve communication during development. Selection of the organism to be used in production must take into consideration both the structure of the protein and the quality and safety of the final product. New technologies require a considerable investment in new manufacturing facilities and equipment. Often, the decision for such an investment must be made early and with a high degree of uncertainty. Desired product yield, expected dosage, and estimated market potential are the most important considerations in this decision. Following public disclosure of the plan to develop recombinant DNA-derived products, approval of the production plant and expansion or adaptation to the new process and technology may be delayed. For this reason, they should be considered as a critical step in the overall development phase. Recruitment of qualified staff is a time-consuming and critical element of the production process. Its impact on the product timeline should not be underestimated, especially if such technologies are new to the company. The entire production process must be validated in respect to identity, purity, and safety of the product to guarantee constant product quality, as well as for safety aspects in the environment. Adequate in-process and final product controls have to be established and specifications determined for release or rejection of batches for preclinical and clinical studies as well as for marketing. Preclinical testing is limited because recombinant DNA-derived proteins cannot be differentiated from naturally occurring human proteins, and because some proteins are species-specific.

Phenodynamics of production and chemical pools in mayapple and flowering dogwood

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, F.G. Jr.

1991-01-01

The objective of this study is to provide an understanding of the seasonality of biomass production and chemical storage among selected forest species as an aid to the analysis and management of a forest ecosystem model. The specific goals to accomplish the objectives included: (1) the construction of phenological calendars to be superimposed on the civil calendar, such that the seasons of the year are not marked by calendar dates but rather by dated groups of phenological events; (2) to develop a capability to predict onset of the generative phase (flowering) from heat unit summation methods; (3) to illustrate themore » role of phenology to biomass production and chemical storage in two indicator species, mayapple and flowering dogwood; and (4) to develop the capability to predict aboveground and below ground standing crop biomass in dogwood. Observations in this study focused on the generative phases (flowering) of individual plants and colonies of plants as indicators of productivity. 16 figs., 11 tabs.« less

Modeling the Transition From Predominantly Gas- to Predominantly Aerosol-Phase Products From OH Reactions With the Homologous Series of C10 to C15 n- Alkanes

NASA Astrophysics Data System (ADS)

Jordan, C. E.; Ziemann, P. J.; Griffin, R. J.; Lim, Y. B.; Atkinson, R.; Arey, J.

2006-12-01

Recent laboratory studies have shown significant formation of secondary organic aerosol (SOA) from OH reactions with a homologous series of n-alkanes. SOA mass yields of 56% were observed for pentadecane (C15), while only 0.5% yield was observed from octane (C8, the smallest alkane in the series). A rapid transition in SOA yield is observed from C10 to C13, with SOA yields increasing from 4% to 49%. In standard gas-aerosol partitioning theory, the vapor pressure controls the amount of material that can condense into the particle phase. However, the rapid transition observed here suggests there may also be a shift in the predominant reaction pathways for longer chain alkanes, leading to greater production of lower vapor pressure products. Here we present an investigation of the role of vapor pressure versus the role of shifting branching ratios to test the influence of each of these on SOA mass yields. We have added each of the alkanes in this series to the Caltech Atmospheric Chemistry Mechanism (CACM). This mechanism was developed in part to predict explicitly concentrations of secondary and tertiary semivolatile oxidation products that potentially form SOA. Although it is has been developed to lump similar compounds together for computational efficiency, it is nonetheless easily adapted and ideally suited for a detailed zero-dimensional modeling study of this kind. This gas-phase mechanism is linked to the aerosol partitioning module MPMPO (Model to Predict the Multi- phase Partitioning of Organics). MPMPO is a fully coupled module that allows the simultaneous partitioning of semi-volatile species to both an aqueous and an organic aerosol phase.

Large bond-dimension time-evolution block decimation study of the XXZ quantum spin chains of S = 1/2 and 1

NASA Astrophysics Data System (ADS)

Choi, Hwan Bin; Lee, Ji-Woo

2017-09-01

We study quantum phase transitions of a XXZ spin model with spin S = 1/2 and 1 in one dimension. The XXZ spin chain is one of basic models in understanding various one-dimensional magnetic materials. To study this model, we construct infinite-lattice matrix product state (iMPS), which is a tensor product form for a one-dimensional many-body quantum wave function. By using timeevolution- block-decimation method (TEBD) on iMPS, we obtain the ground states of the XXZ model at zero temperature. This method is very delicate in calculating ground states so that we developed a reliable method of finding the ground state with the dimension of entanglement coefficients up to 300, which is beyond the previous works. By analyzing ground-state energies, half-chain entanglement entropies, and entanglement spectrum, we found the signatures of quantum phase transitions between ferromagnetic phase, XY phase, Haldane phase, and antiferromagnetic phase.

Using an agent-based model to evaluate the effect of producer specialization on the epidemiological resilience of livestock production networks.

PubMed

Wiltshire, Serge W

2018-01-01

An agent-based computer model that builds representative regional U.S. hog production networks was developed and employed to assess the potential impact of the ongoing trend towards increased producer specialization upon network-level resilience to catastrophic disease outbreaks. Empirical analyses suggest that the spatial distribution and connectivity patterns of contact networks often predict epidemic spreading dynamics. Our model heuristically generates realistic systems composed of hog producer, feed mill, and slaughter plant agents. Network edges are added during each run as agents exchange livestock and feed. The heuristics governing agents' contact patterns account for factors including their industry roles, physical proximities, and the age of their livestock. In each run, an infection is introduced, and may spread according to probabilities associated with the various modes of contact. For each of three treatments-defined by one-phase, two-phase, and three-phase production systems-a parameter variation experiment examines the impact of the spatial density of producer agents in the system upon the length and size of disease outbreaks. Resulting data show phase transitions whereby, above some density threshold, systemic outbreaks become possible, echoing findings from percolation theory. Data analysis reveals that multi-phase production systems are vulnerable to catastrophic outbreaks at lower spatial densities, have more abrupt percolation transitions, and are characterized by less-predictable outbreak scales and durations. Key differences in network-level metrics shed light on these results, suggesting that the absence of potentially-bridging producer-producer edges may be largely responsible for the superior disease resilience of single-phase "farrow to finish" production systems.

Development of processes for the production of solar grade silicon from halides and alkali metals, phase 1 and phase 2

NASA Technical Reports Server (NTRS)

Dickson, C. R.; Gould, R. K.; Felder, W.

1981-01-01

High temperature reactions of silicon halides with alkali metals for the production of solar grade silicon are described. Product separation and collection processes were evaluated, measure heat release parameters for scaling purposes and effects of reactants and/or products on materials of reactor construction were determined, and preliminary engineering and economic analysis of a scaled up process were made. The feasibility of the basic process to make and collect silicon was demonstrated. The jet impaction/separation process was demonstrated to be a purification process. The rate at which gas phase species from silicon particle precursors, the time required for silane decomposition to produce particles, and the competing rate of growth of silicon seed particles injected into a decomposing silane environment were determined. The extent of silane decomposition as a function of residence time, temperature, and pressure was measured by infrared absorption spectroscopy. A simplistic model is presented to explain the growth of silicon in a decomposing silane enviroment.

Preparation and quantification of the total phenolic products in Citrus fruit using solid-phase extraction coupled with high-performance liquid chromatography with diode array and UV detection.

PubMed

Zeng, Honglian; Liu, Zhenli; Zhao, Siyu; Shu, Yisong; Song, Zhiqian; Wang, Chun; Dong, Yunzhuo; Ning, Zhangchi; He, Dan; Wang, Menglei; Lu, Cheng; Liu, Yuanyan; Lu, Aiping

2016-10-01

Citrus fruit is an important health-promoting food that is rich in dietary phenolic metabolites. Traditional Chinese medicines, such as Zhishi and Zhiqiao, come from young and immature fruits of Citrus cultivars. The preparation of diversified bioactive phenolic products and establishment of the corresponding quality control methodology are challenging and necessary. In the current study, four types of solid-phase extraction sorbents for the enrichment and clean-up of the phenolic matrix were evaluated. A solid-phase extraction column coated with Strata-X was finally used in the procedure. Twenty phenolic compounds were selected to evaluate the extraction performances of the sorbents using high-performance liquid chromatography analysis. Under the optimized conditions, good linearities were obtained with R 2 more than 0.9996 for all analytes with LODs of 0.04-1.012 μg/g. Intra- and interday relative standard deviation values were less than 3%, and the recovery was equal to or higher than 90.02%. Compared to non-solid-phase extraction process, the content of total phenolic products was elevated 35.55-68.48% with solid-phase extraction. Finally, the developed and validated method was successfully applied to the discrimination of Zhishi samples from different species as well as Zhishi and Zhiqiao samples in different development stages. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Balanced Depth and Breadth in a New Interdisciplinary Nanotechnology Course

ERIC Educational Resources Information Center

Jiao, Lihong; Barakat, Nael

2012-01-01

The field of nanotechnology has outgrown the discovery phase into the application and even commercial production phases. Consequently, the need for a workforce capable of supporting this growth is more than ever. However, because of the different challenges associated with nanotechnology education, specific courses are required to be developed and…

Fly-by-light flight control system technology development plan

NASA Technical Reports Server (NTRS)

Chakravarty, A.; Berwick, J. W.; Griffith, D. M.; Marston, S. E.; Norton, R. L.

1990-01-01

The results of a four-month, phased effort to develop a Fly-by-Light Technology Development Plan are documented. The technical shortfalls for each phase were identified and a development plan to bridge the technical gap was developed. The production configuration was defined for a 757-type airplane, but it is suggested that the demonstration flight be conducted on the NASA Transport Systems Research Vehicle. The modifications required and verification and validation issues are delineated in this report. A detailed schedule for the phased introduction of fly-by-light system components has been generated. It is concluded that a fiber-optics program would contribute significantly toward developing the required state of readiness that will make a fly-by-light control system not only cost effective but reliable without mitigating the weight and high-energy radio frequency related benefits.

A novel in situ gas stripping-pervaporation process integrated with acetone-butanol-ethanol fermentation for hyper n-butanol production.

PubMed

Xue, Chuang; Liu, Fangfang; Xu, Mengmeng; Zhao, Jingbo; Chen, Lijie; Ren, Jiangang; Bai, Fengwu; Yang, Shang-Tian

2016-01-01

Butanol is considered as an advanced biofuel, the development of which is restricted by the intensive energy consumption of product recovery. A novel two-stage gas stripping-pervaporation process integrated with acetone-butanol-ethanol (ABE) fermentation was developed for butanol recovery, with gas stripping as the first-stage and pervaporation as the second-stage using the carbon nanotubes (CNTs) filled polydimethylsiloxane (PDMS) mixed matrix membrane (MMM). Compared to batch fermentation without butanol recovery, more ABE (27.5 g/L acetone, 75.5 g/L butanol, 7.0 g/L ethanol vs. 7.9 g/L acetone, 16.2 g/L butanol, 1.4 g/L ethanol) were produced in the fed-batch fermentation, with a higher butanol productivity (0.34 g/L · h vs. 0.30 g/L · h) due to reduced butanol inhibition by butanol recovery. The first-stage gas stripping produced a condensate containing 155.6 g/L butanol (199.9 g/L ABE), which after phase separation formed an organic phase containing 610.8 g/L butanol (656.1 g/L ABE) and an aqueous phase containing 85.6 g/L butanol (129.7 g/L ABE). Fed with the aqueous phase of the condensate from first-stage gas stripping, the second-stage pervaporation using the CNTs-PDMS MMM produced a condensate containing 441.7 g/L butanol (593.2 g/L ABE), which after mixing with the organic phase from gas stripping gave a highly concentrated product containing 521.3 g/L butanol (622.9 g/L ABE). The outstanding performance of CNTs-PDMS MMM can be attributed to the hydrophobic CNTs giving an alternative route for mass transport through the inner tubes or along the smooth surface of CNTs. This gas stripping-pervaporation process with less contaminated risk is thus effective in increasing butanol production and reducing energy consumption. © 2015 Wiley Periodicals, Inc.

Volatilization of low vapor pressure--volatile organic compounds (LVP-VOCs) during three cleaning products-associated activities: Potential contributions to ozone formation.

PubMed

Shin, Hyeong-Moo; McKone, Thomas E; Bennett, Deborah H

2016-06-01

There have been many studies to reduce ozone formation mostly from volatile organic compound (VOC) sources. However, the role of low vapor pressure (LVP)-VOCs from consumer products remains mostly unexplored and unaddressed. This study explores the impact of high production volume LVP-VOCs on ozone formation from three cleaning products-associated activities (dishwashing, clothes washing, and surface cleaning). We develop a model framework to account for the portion available for ozone formation during the use phase and from the down-the-drain disposal. We apply experimental studies that measured emission rates or models that were developed for estimating emission rates of organic compounds during the use phase. Then, the fraction volatilized (fvolatilized) and the fraction disposed down the drain (fdown-the-drain) are multiplied by the portion available for ozone formation for releases to the outdoor air (fO3|volatilized) and down-the-drain (fO3|down-the-drain), respectively. Overall, for chemicals used in three specific cleaning-product uses, fvolatilized is less than 0.6% for all studied LVP-VOCs. Because greater than 99.4% of compounds are disposed of down the drain during the use phase, when combined with fO3|volatilized and fO3|down-the-drain, the portion available for ozone formation from the direct releases to outdoor air and the down-the-drain disposal is less than 0.4% and 0.2%, respectively. The results from this study indicate that the impact of the studied LVP-VOCs on ozone formation is very sensitive to what occurs during the use phase and suggest the need for future research on experimental work at the point of use. Copyright © 2016 Elsevier Ltd. All rights reserved.

Simultaneous determination of polycyclic aromatic hydrocarbons and their chlorination by-products in drinking water and the coatings of water pipes by automated solid-phase microextraction followed by gas chromatography-mass spectrometry.

PubMed

Tillner, Jocelyn; Hollard, Caroline; Bach, Cristina; Rosin, Christophe; Munoz, Jean-François; Dauchy, Xavier

2013-11-08

In this study, an automated method for the simultaneous determination of polycyclic aromatic hydrocarbons (PAHs) and their chlorination by-products in drinking water was developed based on online solid-phase microextraction-gas chromatography-mass spectrometry. The main focus was the optimisation of the solid-phase microextraction step. The influence of the agitation rate, type of fibre, desorption time, extraction time, extraction temperature, desorption temperature, and solvent addition was examined. The method was developed and validated using a mixture of 17 PAHs, 11 potential chlorination by-products (chlorinated and oxidised PAHs) and 6 deuterated standards. The limit of quantification was 10 ng/L for all target compounds. The validated method was used to analyse drinking water samples from three different drinking water distribution networks and the presumably coal tar-based pipe coatings of two pipe sections. A number of PAHs were detected in all three networks although individual compositions varied. Several PAH chlorination by-products (anthraquinone, fluorenone, cyclopenta[d,e,f]phenanthrenone, 3-chlorofluoranthene, and 1-chloropyrene) were also found, their presence correlating closely with that of their respective parent compounds. Their concentrations were always below 100 ng/L. In the coatings, all PAHs targeted were detected although concentrations varied between the two coatings (76-12,635 mg/kg and 12-6295 mg/kg, respectively). A number of chlorination by-products (anthraquinone, fluorenone, cyclopenta[d,e,f]phenanthrenone, 3-chlorofluoranthene, and 1-chloropyrene) were also detected (from 40 to 985 mg/kg), suggesting that the reaction of PAHs with disinfectant agents takes place in the coatings and not in the water phase after migration. Copyright © 2013 Elsevier B.V. All rights reserved.

Enhancement of L-phenylalanine production by engineered Escherichia coli using phased exponential L-tyrosine feeding combined with nitrogen source optimization.

PubMed

Yuan, Peipei; Cao, Weijia; Wang, Zhen; Chen, Kequan; Li, Yan; Ouyang, Pingkai

2015-07-01

Nitrogen source optimization combined with phased exponential L-tyrosine feeding was employed to enhance L-phenylalanine production by a tyrosine-auxotroph strain, Escherichia coli YP1617. The absence of (NH4)2SO4, the use of corn steep powder and yeast extract as composite organic nitrogen source were more suitable for cell growth and L-phenylalanine production. Moreover, the optimal initial L-tyrosine level was 0.3 g L(-1) and exponential L-tyrosine feeding slightly improved L-phenylalanine production. Nerveless, L-phenylalanine production was greatly enhanced by a strategy of phased exponential L-tyrosine feeding, where exponential feeding was started at the set specific growth rate of 0.08, 0.05, and 0.02 h(-1) after 12, 32, and 52 h, respectively. Compared with exponential L-tyrosine feeding at the set specific growth rate of 0.08 h(-1), the developed strategy obtained a 15.33% increase in L-phenylalanine production (L-phenylalanine of 56.20 g L(-1)) and a 45.28% decrease in L-tyrosine supplementation. Copyright © 2014 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

NASA's commercial research plans and opportunities

NASA Technical Reports Server (NTRS)

Arnold, Ray J.

1992-01-01

One of the primary goals of the National Aeronautics and Space Administration's (NASA) commercial space development plan is to encourage the development of space-based products and markets, along with the infrastructure and transportation that will support those products and markets. A three phased program has been instituted to carry out this program. The first phase utilizes government grants through the Centers for the Commercial Development of Space (CCDS) for space-related, industry driven research; the development of a technology data base; and the development of commercial space transportation and infrastructure. The second phase includes the development of these technologies by industry for new commercial markets, and features unique industry/government collaborations such as Joint Endeavor Agreements. The final phase will feature technical applications actually brought to the marketplace. The government's role will be to support industry required infrastructure to encourage start-up markets and industries through follow-on development agreements such as the Space Systems Development Agreement. The Office of Commercial Programs has an aggressive flight program underway on the Space Shuttle, suborbital rockets, orbital expendable launch vehicles, and the Commercial Middeck Accommodation Module with SPACEHAB Inc. The Office of Commercial Program's has been allocated 35 percent of the U.S. share of the Space Station Freedom resources for 1997 utilization. A utilization plan has been developed with the Centers for the Commercial Development of Space and has identified eleven materials processing and biotechnology payloads occupying 5 double racks in the pressurized module as well as two payloads external to the module in materials exposure and environment monitoring. The Office of Commercial Programs will rely on the Space Station Freedom to provide the long duration laboratory component for space-based commercial research.

NASA's commercial research plans and opportunities

NASA Astrophysics Data System (ADS)

Arnold, Ray J.

One of the primary goals of the National Aeronautics and Space Administration's (NASA) commercial space development plan is to encourage the development of space-based products and markets, along with the infrastructure and transportation that will support those products and markets. A three phased program has been instituted to carry out this program. The first phase utilizes government grants through the Centers for the Commercial Development of Space (CCDS) for space-related, industry driven research; the development of a technology data base; and the development of commercial space transportation and infrastructure. The second phase includes the development of these technologies by industry for new commercial markets, and features unique industry/government collaborations such as Joint Endeavor Agreements. The final phase will feature technical applications actually brought to the marketplace. The government's role will be to support industry required infrastructure to encourage start-up markets and industries through follow-on development agreements such as the Space Systems Development Agreement. The Office of Commercial Programs has an aggressive flight program underway on the Space Shuttle, suborbital rockets, orbital expendable launch vehicles, and the Commercial Middeck Accommodation Module with SPACEHAB Inc. The Office of Commercial Program's has been allocated 35 percent of the U.S. share of the Space Station Freedom resources for 1997 utilization. A utilization plan has been developed with the Centers for the Commercial Development of Space and has identified eleven materials processing and biotechnology payloads occupying 5 double racks in the pressurized module as well as two payloads external to the module in materials exposure and environment monitoring. The Office of Commercial Programs will rely on the Space Station Freedom to provide the long duration laboratory component for space-based commercial research.

Optimizing product life cycle processes in design phase

NASA Astrophysics Data System (ADS)

Faneye, Ola. B.; Anderl, Reiner

2002-02-01

Life cycle concepts do not only serve as basis in assisting product developers understand the dependencies between products and their life cycles, they also help in identifying potential opportunities for improvement in products. Common traditional concepts focus mainly on energy and material flow across life phases, necessitating the availability of metrics derived from a reference product. Knowledge of life cycle processes won from an existing product is directly reused in its redesign. Depending on sales volume nevertheless, the environmental impact before product optimization can be substantial. With modern information technologies today, computer-aided life cycle methodologies can be applied well before product use. On the basis of a virtual prototype, life cycle processes are analyzed and optimized, using simulation techniques. This preventive approach does not only help in minimizing (or even eliminating) environmental burdens caused by product, costs incurred due to changes in real product can also be avoided. The paper highlights the relationship between product and life cycle and presents a computer-based methodology for optimizing the product life cycle during design, as presented by SFB 392: Design for Environment - Methods and Tools at Technical University, Darmstadt.

Development of an improved system for contract time determination : phase III.

DOT National Transportation Integrated Search

2010-09-30

This study developed Daily Work Report (DWR) based prediction models to determine reasonable : production rates of controlling activities of highway projects. The study used available resources such as : DWR, soil data, AADT and other existing projec...

Pungency Quantitation of Hot Pepper Sauces Using HPLC

NASA Astrophysics Data System (ADS)

Betts, Thomas A.

1999-02-01

A class of compounds known as capsaicinoids are responsible for the "heat" of hot peppers. To determine the pungency of a particular pepper or pepper product, one may quantify the capsaicinoids and relate those concentrations to the perceived heat. The format of the laboratory described here allows students to collectively develop an HPLC method for the quantitation of the two predominant capsaicinoids (capsaicin and dihydrocapsaicin) in hot-pepper products. Each small group of students investigated one of the following aspects of the method: detector wavelength, mobile-phase composition, extraction of capsaicinoids, calibration, and quantitation. The format of the lab forced students to communicate and cooperate to develop this method. The resulting HPLC method involves extraction with acetonitrile followed by solid-phase extraction clean-up, an isocratic 80:20 methanol-water mobile phase, a 4.6 mm by 25 cm C-18 column, and UV absorbance detection at 284 nm. The method developed by the students was then applied to the quantitation of capsaicinoids in a variety of hot pepper sauces. Editor's Note on Hazards in our April 2000 issue addresses the above.

Space station WP-04 power system. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

Hallinan, G. J.

1987-01-01

Major study activities and results of the phase B study contract for the preliminary design of the space station Electrical Power System (EPS) are summarized. The areas addressed include the general system design, man-tended option, automation and robotics, evolutionary growth, software development environment, advanced development, customer accommodations, operations planning, product assurance, and design and development phase planning. The EPS consists of a combination photovoltaic and solar dynamic power generation subsystem and a power management and distribution (PMAD) subsystem. System trade studies and costing activities are also summarized.

Sodium-sulfur battery development. Phase VB final report, October 1, 1981--February 28, 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1985-04-01

This report describes the technical progress made under Contract No. DE-AM04-79CH10012 between the U.S. Department of Energy, Ford Aerospace & Communications Corporations and Ford Motor Company, for the period 1 October 1981 through 28 February 1985, which is designated as Phase VB of the Sodium-Sulfur Battery Development Program. During this period, Ford Aerospace held prime technical responsibility and Ford Motor Company carried out supporting research. Ceramatec, Inc., was a major subcontractor to Ford Aerospace for electrolyte development and production.

One approach for evaluating the Distributed Computing Design System (DCDS)

NASA Technical Reports Server (NTRS)

Ellis, J. T.

1985-01-01

The Distributed Computer Design System (DCDS) provides an integrated environment to support the life cycle of developing real-time distributed computing systems. The primary focus of DCDS is to significantly increase system reliability and software development productivity, and to minimize schedule and cost risk. DCDS consists of integrated methodologies, languages, and tools to support the life cycle of developing distributed software and systems. Smooth and well-defined transistions from phase to phase, language to language, and tool to tool provide a unique and unified environment. An approach to evaluating DCDS highlights its benefits.

Identification of Forced Degradation Products of Itopride by LC-PDA and LC-MS.

PubMed

Joshi, Payal; Bhoir, Suvarna; Bhagwat, A M; Vishwanath, K; Jadhav, R K

2011-05-01

Degradation products of itopride formed under different forced conditions have been identified using LC-PDA and LC-MS techniques. Itopride was subjected to forced degradation under the conditions of hydrolysis, photolysis, oxidation, dry and wet heat, in accordance with the International Conference on Harmonization. The stress solutions were chromatographed on reversed phase C18 (250×4.6 mm, 5 μm) column with a mobile phase methanol:water (55:45, v/v) at a detection wavelength of 215 nm. Itopride degraded in acid, alkali and oxidative stress conditions. The stability indicating method was developed and validated. The degradation pathway of the drug to products II-VIII is proposed.

Identification of Forced Degradation Products of Itopride by LC-PDA and LC-MS

PubMed Central

Joshi, Payal; Bhoir, Suvarna; Bhagwat, A. M.; Vishwanath, K.; Jadhav, R. K.

2011-01-01

Degradation products of itopride formed under different forced conditions have been identified using LC-PDA and LC-MS techniques. Itopride was subjected to forced degradation under the conditions of hydrolysis, photolysis, oxidation, dry and wet heat, in accordance with the International Conference on Harmonization. The stress solutions were chromatographed on reversed phase C18 (250×4.6 mm, 5 μm) column with a mobile phase methanol:water (55:45, v/v) at a detection wavelength of 215 nm. Itopride degraded in acid, alkali and oxidative stress conditions. The stability indicating method was developed and validated. The degradation pathway of the drug to products II-VIII is proposed. PMID:22457552

Applying innovative approach “Nature of Science (NoS) within inquiry” for developing scientific literacy in the student worksheet

NASA Astrophysics Data System (ADS)

Widowati, A.; Anjarsari, P.; Zuhdan, K. P.; Dita, A.

2018-03-01

The challenges of the 21st century require innovative solutions. Education must able to make an understanding of science learning that leads to the formation of scientific literacy learners. This research was conducted to produce the prototype as science worksheet based on Nature of Science (NoS) within inquiry approach and to know the effectiveness its product for developing scientific literacy. This research was the development and research design, by pointing to Four D models and Borg & Gall Model. There were 4 main phases (define, design, develop, disseminate) and additional phases (preliminary field testing, main product revision, main field testing, and operational product revision). Research subjects were students of the junior high school in Yogyakarta. The instruments used included questionnaire sheet product validation and scientific literacy test. For the validation data were analyzed descriptively. The test result was analyzed by an N-gain score. The results showed that the appropriateness of worksheet applying NoS within inquiry-based learning approach is eligible based on the assessment from excellent by experts and teachers, students’ scientific literacy can improve high category of the N-gain score at 0.71 by using student worksheet with Nature of Science (NoS) within inquiry approach.

49 CFR 236.913 - Filing and approval of PSPs.

Code of Federal Regulations, 2011 CFR

2011-10-01

... architectural concepts; the PSP describes a product that uses design or safety assurance concepts considered... the end of the system design review phase of product development and 180 days prior to planned implementation, inviting FRA to participate in the design review process and receive periodic briefings and...

49 CFR 236.913 - Filing and approval of PSPs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... architectural concepts; the PSP describes a product that uses design or safety assurance concepts considered... the end of the system design review phase of product development and 180 days prior to planned implementation, inviting FRA to participate in the design review process and receive periodic briefings and...

APPLICATION OF SOLID PHASE MICROEXTRACTION GC/MS TO THE CHARACTERIZATION OF HYDROPHILIC DISINFECTION BY-PRODUCTS IN WATER

EPA Science Inventory

The U.S. Environmental Protection Agency has given high priority to research aimed at developing methods to extract hydrophilic disinfection by-products (DBPs) from drinking water. Public water supplies are treated with a variety of chemicals aimed at reducing or eliminating inf...

A STUDY OF THE FEASIBILITY OF UTILIZING SOLID WASTES FOR BUILDING MATERIALS. PHASE III AND IV SUMMARY REPORTS

EPA Science Inventory

This report summarizes work to develop building materials containing inorganic and organic wastes and wastes-derived products. Attempts were made to produce full-scale products and qualify them for structural applications. Particle board panels were made of peanut hulls and wood ...

Process-Product Research: A Cornerstone in Educational Effectiveness Research

ERIC Educational Resources Information Center

Creemers, Bert; Kyriakides, Leonidas

2015-01-01

This article links the contribution of process-product studies in developing the theoretical framework of educational effectiveness by pointing out the importance of teacher behavior in the classroom. The role that Jere Brophy played in this evolving research is described within the various phases of teacher effectiveness research. Process-product…

21 CFR 809.10 - Labeling for in vitro diagnostic products.

Code of Federal Regulations, 2012 CFR

2012-04-01

... procedure, e.g., qualitative or quantitative. (3) Summary and explanation of the test. Include a short... provides other than quantitative results, provide an adequate description of expected results. (10... are met: (i) For a product in the laboratory research phase of development, and not represented as an...

21 CFR 809.10 - Labeling for in vitro diagnostic products.

Code of Federal Regulations, 2011 CFR

2011-04-01

... procedure, e.g., qualitative or quantitative. (3) Summary and explanation of the test. Include a short... provides other than quantitative results, provide an adequate description of expected results. (10... are met: (i) For a product in the laboratory research phase of development, and not represented as an...

21 CFR 809.10 - Labeling for in vitro diagnostic products.

Code of Federal Regulations, 2013 CFR

2013-04-01

... procedure, e.g., qualitative or quantitative. (3) Summary and explanation of the test. Include a short... provides other than quantitative results, provide an adequate description of expected results. (10... are met: (i) For a product in the laboratory research phase of development, and not represented as an...

21 CFR 809.10 - Labeling for in vitro diagnostic products.

Code of Federal Regulations, 2014 CFR

2014-04-01

... procedure, e.g., qualitative or quantitative. (3) Summary and explanation of the test. Include a short... provides other than quantitative results, provide an adequate description of expected results. (10... are met: (i) For a product in the laboratory research phase of development, and not represented as an...

Life cycle assessment of a road safety product made with virgin and recycled HDPE.

PubMed

Simões, Carla L; Xará, Susana M; Bernardo, C A

2011-04-01

The present study aims at evaluating the potential environmental impact of using recycled high-density polyethylene (HDPE) in the production of an anti-glare lamella (AGL), a road safety device currently manufactured from virgin (not recycled) polymer. The impact was evaluated using the life cycle assessment (LCA) technique and comparing two alternative systems: current AGL, manufactured from virgin HDPE, and optional AGL, made with recycled HDPE obtained from post-consumer packages. The AGL manufacturing phase was found to be responsible for most of the impacts in both systems, with the production of the raw material being the largest contributor for that phase. The present study makes a contribution to the problem of developing value-added products made from post-consumer polymeric recyclates.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levy, E.; Mullens, M.; Rath, P.

The Advanced Envelope Research effort will provide factory homebuilders with high performance, cost-effective envelope designs that can be effectively integrated into the plant production process while meeting the thermal requirements of the 2012 IECC standards. This work is part of a multiphase effort. Phase 1 identified seven envelope technologies and provided a preliminary assessment of three methods for building high performance walls. Phase 2 focused on developing viable product designs, manufacturing strategies, addressing code and structural issues, and cost analysis of the three selected options. An industry advisory committee helped narrow the research focus to perfecting a stud wall designmore » with exterior continuous insulation (CI). This report describes Phase 3, which was completed in two stages and continued the design development effort, exploring and evaluating a range or methods for applying CI to factory built homes. The scope also included material selection, manufacturing and cost analysis, and prototyping and testing. During this phase, a home was built with CI, evaluated, and placed in service. The experience of building a mock up wall section with CI and then constructing on line a prototype home resolved important concerns about how to integrate the material into the production process. First steps were taken toward finding least expensive approaches for incorporating CI in standard factory building practices and a preliminary assessment suggested that even at this early stage the technology is attractive when viewed from a life cycle cost perspective.« less

Mechanistic Studies Of Combustion And Structure Formation During Combustion Synthesis Of Advanced Materials: Phase Separation Mechanism For Bio-Alloys

NASA Technical Reports Server (NTRS)

Varma, A.; Lau, C.; Mukasyan, A.

2003-01-01

Among all implant materials, Co-Cr-Mo alloys demonstrate perhaps the most useful balance of resistance to corrosion, fatigue and wear, along with strength and biocompatibility [1]. Currently, these widely used alloys are produced by conventional furnace technology. Owing to high melting points of the main alloy elements (e.g. Tm.p.(Co) 1768 K), high-temperature furnaces and long process times (several hours) are required. Therefore, attempts to develop more efficient and flexible methods for production of such alloys with superior properties are of great interest. The synthesis of materials using combustion phenomena is an advanced approach in powder metallurgy [2]. The process is characterized by unique conditions involving extremely fast heating rates (up to 10(exp 6 K/s), high temperatures (up to 3500 K), and short reaction times (on the order of seconds). As a result, combustion synthesis (CS) offers several attractive advantages over conventional metallurgical processing and alloy development technologies. The foremost is that solely the heat of chemical reaction (instead of an external source) supplies the energy for the synthesis. Also, simple equipment, rather than energy-intensive high-temperature furnaces, is sufficient. This work was devoted to experiments on CS of Co-based alloys by utilizing thermite (metal oxide-reducing metal) reactions, where phase separation subsequently produces materials with tailored compositions and properties. Owing to high reaction exothermicity, the CS process results in a significant increase of temperature (up to 3000 C), which is higher than melting points of all products. Since the products differ in density, phase separation may be a gravitydriven process: the heavy (metallic phase) settles while the light (slag) phase floats. The goal was to determine if buoyancy is indeed the major mechanism that controls phase segregation.

Artificial intelligence approaches to software engineering

NASA Technical Reports Server (NTRS)

Johannes, James D.; Macdonald, James R.

1988-01-01

Artificial intelligence approaches to software engineering are examined. The software development life cycle is a sequence of not so well-defined phases. Improved techniques for developing systems have been formulated over the past 15 years, but pressure continues to attempt to reduce current costs. Software development technology seems to be standing still. The primary objective of the knowledge-based approach to software development presented in this paper is to avoid problem areas that lead to schedule slippages, cost overruns, or software products that fall short of their desired goals. Identifying and resolving software problems early, often in the phase in which they first occur, has been shown to contribute significantly to reducing risks in software development. Software development is not a mechanical process but a basic human activity. It requires clear thinking, work, and rework to be successful. The artificial intelligence approaches to software engineering presented support the software development life cycle through the use of software development techniques and methodologies in terms of changing current practices and methods. These should be replaced by better techniques that that improve the process of of software development and the quality of the resulting products. The software development process can be structured into well-defined steps, of which the interfaces are standardized, supported and checked by automated procedures that provide error detection, production of the documentation and ultimately support the actual design of complex programs.

Microbial and nutritional aspects on the production of live feeds in a fish farming industry.

PubMed

De Donno, A; Lugoli, F; Bagordo, F; Vilella, S; Campa, A; Grassi, T; Guido, M

2010-03-01

Aquaculture is an enterprise in constant development, in particular relating to its effect on the environment and also the quality of its products. It represents a valid alternative to traditional fishing, facing the increasing demand for fish products. To guarantee to the consumer a product of high nutritional, organoleptic and hygienic quality, it is fundamental to monitor every phase of the fish farming industry, isolating the potential risk points. For this reason there has been a rapid evolution of productive technique, particularly in the technology, artificial reproduction and feed sectors. The aim of this research has been the monitoring of the evolution of certain microbial and nutritional quality indexes (total microbial counts and lipid analysis on suspensions of Rotifers and Artemia, used as live feed) in the larval phase of the productive cycle of the farm raised fish, in an intensive system. The study has shown an increment in the total microbial counts in the fish farming industry within the production of Rotifers and Artemia, more evident in the suspensions of Rotifers. In addition the study has demonstrated that the maintenance phase, in the enrichment protocol, can reduce the EPA and DHA content. The results confirm the importance of microbial and nutritional control of the live feeds before they get supplied to fish larvae.

Commercial-scale demonstration of the Liquid Phase Methanol (LPMEOH{trademark}) process. Technical progress report number 6, October 1--December 31, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-12-31

The project involves the construction of an 80,000 gallons per day (260 TPD) methanol unit utilizing coal-derived synthesis gas from Eastman`s integrated coal gasification facility. The new equipment consists of synthesis gas feed preparation and compression facilities, the liquid phase reactor and auxiliaries, product distillation facilities, and utilities. The technology to be demonstrated is the product of a cooperative development effort by Air Products and DOE in a program that started in 1981. Developed to enhance electric power generation using integrated gasification combined cycle (IGCC) technology, the LPMEOH{trademark} process is ideally suited for directly processing gases produced by modern-day coalmore » gasifiers. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The slurry dissipates the heat of the chemical reaction away from the catalyst surface protecting the catalyst and allowing the methanol synthesis reaction to proceed at higher rates. At the Eastman complex, the technology will be integrated with existing coal-gasifiers. A carefully developed test plan will allow operations at Eastman to simulate electricity demand load-following in coal-based IGCC facilities. The operations will also demonstrate the enhanced stability and heat dissipation of the conversion process, its reliable on/off operation, and its ability to produce methanol as a clean liquid fuel without additional upgrading. An off-site product testing program will be conducted to demonstrate the suitability of the methanol product as a transportation fuel and as a fuel for stationary applications for small modular electric power generators for distributed power.« less

GROWING ALTERNATIVE SUSTAINABLE BUILDINGS: BIOCOMPOSITE PRODUCTS FROM NATURAL FIBER, BIODEGRADABLE AND RECYCLABLE POLYMER MATERIALS FOR LOAD-BEARING CONSTRUCTION COMPONENTS

EPA Science Inventory

The Phase 2 proposal set out to define a number of limited research objectives to carry the project forward, based on the success of research and design carried out in Phase I through to the development and implementation of the project towards a marketable commodity for th...

IDENTIFYING SUITABLE INDICATORS FOR MEASURING SUSTAINABILITY OF BIOENERGY PRODUCTS DERIVED FROM PINE FORESTS IN THE U.S. SOUTH (PHASE-1)

EPA Science Inventory

Preparation and application of reversed phase chromatorotor for the isolation of natural products by centrifugal preparative chromatography

USDA-ARS?s Scientific Manuscript database

A method of preparation of Chromatorotor or plates with a reversed phase (RP) solid silica gel sorbent layer has been developed for preparative centrifugal chromatography. The RP-rotor plates consist of binder free RP solid SiO2 sorbent layers of different thicknesses paked between two supported cir...

Paving the critical path: how can clinical pharmacology help achieve the vision?

PubMed

Lesko, L J

2007-02-01

It has been almost 3 years since the launch of the FDA critical path initiative following the publication of the paper "Innovation or Stagnation: Challenges and Opportunities on the Critical Path of New Medical Product Development." The initiative was intended to create an urgency with the drug development enterprise to address the so-called "productivity problem" in modern drug development. Clinical pharmacologists are strategically aligned with solutions designed to reduce late phase clinical trial failures to show adequate efficacy and/or safety. This article reviews some of the ways that clinical pharmacologists can lead and implement change in the drug development process. It includes a discussion of model-based, semi-mechanistic drug development, drug/disease models that facilitate informed clinical trial designs and optimal dosing, the qualification process and criteria for new biomarkers and surrogate endpoints, approaches to streamlining clinical trials and new types of interaction between industry and FDA such as the end-of-phase 2A and voluntary genomic data submission meetings respectively.

Methanol production from Eucalyptus wood chips. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fishkind, H.H.

This feasibility study includes all phases of methanol production from seedling to delivery of finished methanol. The study examines: production of 55 million, high quality, Eucalyptus seedlings through tissue culture; establishment of a Eucalyptus energy plantation on approximately 70,000 acres; engineering for a 100 million gallon-per-day methanol production facility; potential environmental impacts of the whole project; safety and health aspects of producing and using methanol; and development of site specific cost estimates.

Nasa's Emerging Productivity Program

NASA Technical Reports Server (NTRS)

Braunstein, D. R.

1984-01-01

The goals, membership, and organizational structure of the NASA Productivity Steering Committee are described as well as steps taken to make NASA a leader in the development and application of productivity and quality concepts at every level of agency management. The overall strategy for the Productivity Improvement and Quality Enhancement (PIQE) Program is through employee involvement, both civil servant and contractor, in all phases of agency-wide activity. Elements of the PIQE program and initial thrusts are examined.

Space station advanced automation

NASA Technical Reports Server (NTRS)

Woods, Donald

1990-01-01

In the development of a safe, productive and maintainable space station, Automation and Robotics (A and R) has been identified as an enabling technology which will allow efficient operation at a reasonable cost. The Space Station Freedom's (SSF) systems are very complex, and interdependent. The usage of Advanced Automation (AA) will help restructure, and integrate system status so that station and ground personnel can operate more efficiently. To use AA technology for the augmentation of system management functions requires a development model which consists of well defined phases of: evaluation, development, integration, and maintenance. The evaluation phase will consider system management functions against traditional solutions, implementation techniques and requirements; the end result of this phase should be a well developed concept along with a feasibility analysis. In the development phase the AA system will be developed in accordance with a traditional Life Cycle Model (LCM) modified for Knowledge Based System (KBS) applications. A way by which both knowledge bases and reasoning techniques can be reused to control costs is explained. During the integration phase the KBS software must be integrated with conventional software, and verified and validated. The Verification and Validation (V and V) techniques applicable to these KBS are based on the ideas of consistency, minimal competency, and graph theory. The maintenance phase will be aided by having well designed and documented KBS software.

Long-term archives of land surface albedo products through the EUMETSAT/LSA-SAF and ECMWF/C3S projects: status and project development plan

NASA Astrophysics Data System (ADS)

Carrer, D.; Pinault, F.; Ceamanos, X.; Meurey, C.; Moparthy, S.; Swinnen, E.; Trigo, I.

2017-12-01

The two space programs of EUMETSAT (project CDOP3, LSA-SAF) and ECMWF (the Copernicus Climate Change Service; C3S_312a Lot9) provide (or will provide) added-value satellite products for the meteorological and environmental science communities, especially in the fields of climate modeling, environmental management, natural hazards management, and climate change detection. The EUMETSAT/LSA-SAF project started in 1999 with research and development activities. The Third Continuous Development and Operations Phase (CDOP-3) starts in March 2017 and will end in 2022. This project uses instruments on board European satellites that were, or will be, launched between 2004 and 2022. Unlike the LSA-SAF, the COPERNICUS/C3S_312a project has no NRT constraint. Its first phase started in november 2016. One of the major objective of the COPERNICUS/C3S_312a project is to harmonize datasets from various sensors in order to provide consistent and continuous ECV products from the 80's until now.Presently, the delivered operational products comprise several surface albedo products using data from various space missions (METEOSAT, NOAA, METOP, …). We present here the portfolio of the surface albedo products that are disseminated with an operational status. Their characteristics and accuracy are detailed here after. Also we will present the development plan to produce long-term re-analysis and to prepare the arrival of the next generation of satellite (MTG, EPS-SG, ...). This work will lead in 2018 to 40 years of products characterizing the albedo properties of the surface. These programs provide a great opportunity to monitor and identify human-induced climate change since consistent production of data sets is guaranteed until at least 2022.

Using an agent-based model to evaluate the effect of producer specialization on the epidemiological resilience of livestock production networks

PubMed Central

2018-01-01

An agent-based computer model that builds representative regional U.S. hog production networks was developed and employed to assess the potential impact of the ongoing trend towards increased producer specialization upon network-level resilience to catastrophic disease outbreaks. Empirical analyses suggest that the spatial distribution and connectivity patterns of contact networks often predict epidemic spreading dynamics. Our model heuristically generates realistic systems composed of hog producer, feed mill, and slaughter plant agents. Network edges are added during each run as agents exchange livestock and feed. The heuristics governing agents’ contact patterns account for factors including their industry roles, physical proximities, and the age of their livestock. In each run, an infection is introduced, and may spread according to probabilities associated with the various modes of contact. For each of three treatments—defined by one-phase, two-phase, and three-phase production systems—a parameter variation experiment examines the impact of the spatial density of producer agents in the system upon the length and size of disease outbreaks. Resulting data show phase transitions whereby, above some density threshold, systemic outbreaks become possible, echoing findings from percolation theory. Data analysis reveals that multi-phase production systems are vulnerable to catastrophic outbreaks at lower spatial densities, have more abrupt percolation transitions, and are characterized by less-predictable outbreak scales and durations. Key differences in network-level metrics shed light on these results, suggesting that the absence of potentially-bridging producer–producer edges may be largely responsible for the superior disease resilience of single-phase “farrow to finish” production systems. PMID:29522574

Optical modular arithmetic

NASA Astrophysics Data System (ADS)

Pavlichin, Dmitri S.; Mabuchi, Hideo

2014-06-01

Nanoscale integrated photonic devices and circuits offer a path to ultra-low power computation at the few-photon level. Here we propose an optical circuit that performs a ubiquitous operation: the controlled, random-access readout of a collection of stored memory phases or, equivalently, the computation of the inner product of a vector of phases with a binary selector" vector, where the arithmetic is done modulo 2pi and the result is encoded in the phase of a coherent field. This circuit, a collection of cascaded interferometers driven by a coherent input field, demonstrates the use of coherence as a computational resource, and of the use of recently-developed mathematical tools for modeling optical circuits with many coupled parts. The construction extends in a straightforward way to the computation of matrix-vector and matrix-matrix products, and, with the inclusion of an optical feedback loop, to the computation of a weighted" readout of stored memory phases. We note some applications of these circuits for error correction and for computing tasks requiring fast vector inner products, e.g. statistical classification and some machine learning algorithms.

Irradiation of fish fillets: Relation of vapor phase reactions to storage quality

USGS Publications Warehouse

Spinelli, J.; Dollar, A.M.; Wedemeyer, G.A.; Gallagher, E.C.

1969-01-01

Fish fillets irradiated under air, nitrogen, oxygen, or carbon dioxide atmospheres developed rancidlike flavors when they were stored at refrigerated temperatures. Packing and irradiating under vacuum or helium prevented development of off-flavors during storage.Significant quantities of nitrate and oxidizing substances were formed when oxygen, nitrogen, or air were present in the vapor or liquid phases contained in a Pyrex glass model system exposed to ionizing radiation supplied by a 60Co source. It was demonstrated that the delayed flavor changes that occur in stored fish fillets result from the reaction of vapor phase radiolysis products and the fish tissue substrates.

Innovative grinding wheel design for cost-effective machining of advanced ceramics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Licht, R.H.; Kuo, P.; Liu, S.

2000-05-01

This Final Report covers the Phase II Innovative Grinding Wheel (IGW) program in which Norton Company successfully developed a novel grinding wheel for cost-effective cylindrical grinding of advanced ceramics. In 1995, Norton Company successfully completed the 16-month Phase I technical effort to define requirements, design, develop, and evaluate a next-generation grinding wheel for cost-effective cylindrical grinding of advanced ceramics using small prototype wheels. The Phase II program was initiated to scale-up the new superabrasive wheel specification to larger diameters, 305-mm to 406-mm, required for most production grinding of cylindrical ceramic parts, and to perform in-house and independent validation grinding tests.

Vulnerability of Thai rice production to simultaneous climate and socioeconomic changes: a double exposure analysis

NASA Astrophysics Data System (ADS)

Sangpenchan, R.

2011-12-01

This research explores the vulnerability of Thai rice production to simultaneous exposure by climate and socioeconomic change -- so-called "double exposure." Both processes influence Thailand's rice production system, but the vulnerabilities associated with their interactions are unknown. To understand this double exposure, I adopts a mixed-method, qualitative-quantitative analytical approach consisting of three phases of analysis involving a Vulnerability Scoping Diagram, a Principal Component Analysis, and the EPIC crop model using proxy datasets collected from secondary data sources at provincial scales.The first and second phases identify key variables representing each of the three dimensions of vulnerability -- exposure, sensitivity, and adaptive capacity indicating that the greatest vulnerability in the rice production system occurs in households and areas with high exposure to climate change, high sensitivity to climate and socioeconomic stress, and low adaptive capacity. In the third phase, the EPIC crop model simulates rice yields associated with future climate change projected by CSIRO and MIROC climate models. Climate change-only scenarios project the decrease in yields by 10% from the current productivity during 2016-2025 and 30% during 2045-2054. Scenarios applying both climate change and improved technology and management practices show that a 50% increase in rice production is possible, but requires strong collaboration between sectors to advance agricultural research and technology and requires strong adaptive capacity in the rice production system characterized by well-developed social capital, social networks, financial capacity, and infrastructure and household mobility at the local scale. The vulnerability assessment and climate and crop adaptation simulations used here provide useful information to decision makers developing vulnerability reduction plans in the face of concurrent climate and socioeconomic change.

Quality assurance after process changes of the production of a therapeutic antibody.

PubMed

Brass, J M; Krummen, K; Moll-Kaufmann, C

1996-12-01

Process development for the production of a therapeutic humanised antibody is a very complex operation. It involves recombinant genetics, verification of a strong expression system, gene amplification, characterisation of a stable host cell expression system, optimisation and design of the mammalian cell culture fermentation system and development of an efficient recovery process resulting in high yields and product quality. Rapid progress in the field and the wish of some pharmaceutical companies for outsourcing their production are the driving forces for process changes relatively late in the development phase. This literature survey is aimed at identifying the limits of acceptable process changes in up scaling of the fermentation and down stream processing of biopharmaceuticals and defining the demand in production validation to prove product equivalency and identity of the isolated, purified therapeutic antibody.

A novel computerised image analysis method for the measurement of production of conidia from the aphid pathogenic fungus Erynia neoaphidis.

PubMed

Bonner, Tony J; Pell, Judith K; Gray, Simon N

2003-03-14

A semi-automated method has been developed for the quantification and measurement of conidia discharged by the aphid pathogen Erynia neoaphidis. This was used to compare conidiation by E. neoaphidis-mycosed pea aphid cadavers, mycelial plugs cut from agar plates, mycelial pellets from shake flasks and by mycelial pellets from different phases of liquid batch fermenter culture. Aphid cadavers discharged significantly more and significantly smaller conidia than plugs or pellets. The volume of conidia discharged was stable over the period of discharge (80 h), but more detailed analysis of the size frequency distribution showed that more very small and very large conidia were discharged after 5 h incubation than after 75 h incubation. Biomass harvested at the end of the exponential growth phase in batch fermenter culture produced significantly more conidia than biomass from any other growth phase. The implications of these findings for the development of production and formulation processes for E. neoaphidis as a biological control agent are discussed.

Private investment in AIDS vaccine development: obstacles and solutions.

PubMed Central

Batson, A.; Ainsworth, M.

2001-01-01

The development of vaccines for the prevention of AIDS, malaria, tuberculosis, and other diseases requires both public and private investment. Private investment, however, has been far lower than might have been hoped, given the massive human toll of these diseases, particularly in the poorest countries. With a view to understanding this situation and exploring potential solutions, the World Bank AIDS Vaccine Task Force commissioned a study on the perspectives of the biotechnology, vaccine, and pharmaceutical industries regarding investment in research and development work on an AIDS vaccine. It was found that different obstacles to the development of an AIDS vaccine arose during the product development cycle. During the earlier phases, before obtaining proof of product, the principal barriers were scientific. The lack of consensus on which approach was likely to be effective increased uncertainty and the risks associated with investing in expensive clinical trials. The later phases, which involved adapting, testing, and scaling up production for different populations, were most influenced by market considerations. In order to raise the levels of private research and development in an AIDS vaccine there will probably have to be a combination of push strategies, which reduce the cost and scientific risk of investment, and pull strategies, which guarantee a market. PMID:11545328

Klamath Falls: High-Power Acoustic Well Stimulation Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Black, Brian

Acoustic well stimulation (AWS) technology uses high-power sonic waves from specific frequency spectra in an attempt to stimulate production in a damaged or low-production wellbore. AWS technology is one of the most promising technologies in the oil and gas industry, but it has proven difficult for the industry to develop an effective downhole prototype. This collaboration between Klamath Falls Inc. and the Rocky Mountain Oilfield Testing Center (RMOTC) included a series of tests using high-power ultrasonic tools to stimulate oil and gas production. Phase I testing was designed and implemented to verify tool functionality, power requirements, and capacity of high-powermore » AWS tools. The purpose of Phase II testing was to validate the production response of wells with marginal production rates to AWS stimulation and to capture and identify any changes in the downhole environment after tool deployment. This final report presents methodology and results.« less

Development Directions for Various Types of the Light Wood-Framed Structures

NASA Astrophysics Data System (ADS)

Malesza, J.; Baszeń, M.; Miedziałowski, Cz

2017-11-01

The paper presents current trends in the development of the wood-framed structures. Authors describe the evolution of the technology of implementation, the production process of precast elements of buildings as well as selected realization on the site of these kinds of structures. The attention has been paid to the effect of implementation phases on construction and erecting technology of the wood-framed structures. The paper draws attention to the importance and enhancement of structural analysis of structures in individual phases of building realization.

Phase Change Fabrics Control Temperature

NASA Technical Reports Server (NTRS)

2009-01-01

Originally featured in Spinoff in 1997, Outlast Technologies Inc. (formerly Gateway Technologies Inc.) has built its entire product line on microencapsulated phase change materials, developed in Small Business Innovation Research (SBIR) contracts with Johnson Space Center after initial development for the U.S. Air Force. The Boulder, Colorado-based company acquired the exclusive patent rights and now integrates these materials into textiles or onto finished apparel, providing temperature regulation in bedding materials and a full line of apparel for both ordinary and extreme conditions.

Phased Array Technology with Phase and Amplitude Controlled Magnetron for Microwave Power Transmission

NASA Astrophysics Data System (ADS)

Shinohara, N.; Matsumoto, H.

2004-12-01

We need a microwave power transmitter with light weight and high DC-RF conversion efficiency for an economical SSPS (Space Solar Power System). We need a several g/W for a microwave power transmission (MPT) system with a phased array with 0.0001 degree of beam control accuracy (=tan-1 (100m/36,000km)) and over 80 % of DC-RF conversion efficiency when the weight of the 1GW-class SPS is below a several thousand ton - a several tens of thousand ton. We focus a microwave tube, especially magnetron by economical reason and by the amount of mass-production because it is commonly used for microwave oven in the world. At first, we have developed a phase controlled magnetron (PCM) with different technologies from what Dr. Brown developed. Next we have developed a phase and amplitude controlled magnetron (PACM). For the PACM, we add a feedback to magnetic field of the PCM with an external coil to control and stabilize amplitude of the microwave. We succeed to develop the PACM with below 10-6 of frequency stability and within 1 degree of an error in phase and within 1% of amplitude. We can control a phase and amplitude of the PACM and we have developed a phased array the PCMs. With the PCM technology, we have developed a small light weight MPT transmitter COMET (Compact Microwave Energy Transmitter) with consideration of heat radiation for space use and with consideration of mobility to space.

Case for real-time systems development - Quo vadis?

NASA Technical Reports Server (NTRS)

Erb, Dona M.

1991-01-01

The paper focuses on the distinctive issues of computer-aided software engineering (CASE) products for the development of real-time systems. CASE technologies and associated standardization efforts are evolving from sets of conflicting interests. The majority of case products are intended for use in the development of management information systems. CASE products to support the development of large, complex real-time systems must provide additional capabilities. Generic concerns include the quality of the implementation of the required method for the phase of the system's development and whether the vendor is stable and committed to evolving the products in parallel with nonproprietary standards. The CASE market is undergoing considerable consolidation. The paper describes the major forces, cooperating entities, and remaining uncertainties that need to be weighed in near-term CASE procurements to limit risk of loss of investment in project time, trianing, and money.

M3FT-15OR0202212: SUBMIT SUMMARY REPORT ON THERMODYNAMIC EXPERIMENT AND MODELING

DOE Office of Scientific and Technical Information (OSTI.GOV)

McMurray, Jake W.; Brese, Robert G.; Silva, Chinthaka M.

2015-09-01

Modeling the behavior of nuclear fuel with a physics-based approach uses thermodynamics for key inputs such as chemical potentials and thermal properties for phase transformation, microstructure evolution, and continuum transport simulations. Many of the lanthanide (Ln) elements and Y are high-yield fission products. The U-Y-O and U-Ln-O ternaries are therefore key subsystems of multi-component high-burnup fuel. These elements dissolve in the dominant urania fluorite phase affecting many of its properties. This work reports on an effort to assess the thermodynamics of the U-Pr-O and U-Y-O systems using the CALPHAD (CALculation of PHase Diagrams) method. The models developed within this frameworkmore » are capable of being combined and extended to include additional actinides and fission products allowing calculation of the phase equilibria, thermochemical and material properties of multicomponent fuel with burnup.« less

Toward exascale production of recombinant adeno-associated virus for gene transfer applications.

PubMed

Cecchini, S; Negrete, A; Kotin, R M

2008-06-01

To gain acceptance as a medical treatment, adeno-associated virus (AAV) vectors require a scalable and economical production method. Recent developments indicate that recombinant AAV (rAAV) production in insect cells is compatible with current good manufacturing practice production on an industrial scale. This platform can fully support development of rAAV therapeutics from tissue culture to small animal models, to large animal models, to toxicology studies, to Phase I clinical trials and beyond. Efforts to characterize, optimize and develop insect cell-based rAAV production have culminated in successful bioreactor-scale production of rAAV, with total yields potentially capable of approaching the exa-(10(18)) scale. These advances in large-scale AAV production will allow us to address specific catastrophic, intractable human diseases such as Duchenne muscular dystrophy, for which large amounts of recombinant vector are essential for successful outcome.

A Human-Centered Design Methodology to Enhance the Usability, Human Factors, and User Experience of Connected Health Systems: A Three-Phase Methodology

PubMed Central

Harte, Richard; Glynn, Liam; Rodríguez-Molinero, Alejandro; Baker, Paul MA; Scharf, Thomas; ÓLaighin, Gearóid

2017-01-01

Background Design processes such as human-centered design, which involve the end user throughout the product development and testing process, can be crucial in ensuring that the product meets the needs and capabilities of the user, particularly in terms of safety and user experience. The structured and iterative nature of human-centered design can often present a challenge when design teams are faced with the necessary, rapid, product development life cycles associated with the competitive connected health industry. Objective We wanted to derive a structured methodology that followed the principles of human-centered design that would allow designers and developers to ensure that the needs of the user are taken into account throughout the design process, while maintaining a rapid pace of development. In this paper, we present the methodology and its rationale before outlining how it was applied to assess and enhance the usability, human factors, and user experience of a connected health system known as the Wireless Insole for Independent and Safe Elderly Living (WIISEL) system, a system designed to continuously assess fall risk by measuring gait and balance parameters associated with fall risk. Methods We derived a three-phase methodology. In Phase 1 we emphasized the construction of a use case document. This document can be used to detail the context of use of the system by utilizing storyboarding, paper prototypes, and mock-ups in conjunction with user interviews to gather insightful user feedback on different proposed concepts. In Phase 2 we emphasized the use of expert usability inspections such as heuristic evaluations and cognitive walkthroughs with small multidisciplinary groups to review the prototypes born out of the Phase 1 feedback. Finally, in Phase 3 we emphasized classical user testing with target end users, using various metrics to measure the user experience and improve the final prototypes. Results We report a successful implementation of the methodology for the design and development of a system for detecting and predicting falls in older adults. We describe in detail what testing and evaluation activities we carried out to effectively test the system and overcome usability and human factors problems. Conclusions We feel this methodology can be applied to a wide variety of connected health devices and systems. We consider this a methodology that can be scaled to different-sized projects accordingly. PMID:28302594

Designing for sustained adoption: A model of developing educational innovations for successful propagation

NASA Astrophysics Data System (ADS)

Khatri, Raina; Henderson, Charles; Cole, Renée; Froyd, Jeffrey E.; Friedrichsen, Debra; Stanford, Courtney

2016-06-01

[This paper is part of the Focused Collection on Preparing and Supporting University Physics Educators.] The physics education research community has produced a wealth of knowledge about effective teaching and learning of college level physics. Based on this knowledge, many research-proven instructional strategies and teaching materials have been developed and are currently available to instructors. Unfortunately, these intensive research and development activities have failed to influence the teaching practices of many physics instructors. This paper describes interim results of a larger study to develop a model of designing materials for successful propagation. The larger study includes three phases, the first two of which are reported here. The goal of the first phase was to characterize typical propagation practices of education developers, using data from a survey of 1284 National Science Foundation (NSF) principal investigators and focus group data from eight disciplinary groups of NSF program directors. The goal of the second phase was to develop an understanding of successful practice by studying three instructional strategies that have been well propagated. The result of the first two phases is a tentative model of designing for successful propagation, which will be further validated in the third phase through purposeful sampling of additional well-propagated instructional strategies along with typical education development projects. We found that interaction with potential adopters was one of the key missing ingredients in typical education development activities. Education developers often develop a polished product before getting feedback, rely on mass-market communication channels for dissemination, and do not plan for supporting adopters during implementation. The tentative model resulting from this study identifies three key propagation activities: interactive development, interactive dissemination, and support of adopters. Interactive development uses significant feedback from potential adopters to develop a strong product suitable for use in many settings. Interactive dissemination uses personal interactions to reach and motivate potential users. Support of adopters is missing from typical propagation practice and is important to reduce the burden of implementation and increases the likelihood of successful adoption.

Extension of quality-by-design concept to the early development phase of pharmaceutical R&D processes.

PubMed

Csóka, Ildikó; Pallagi, Edina; Paál, Tamás L

2018-03-27

Here, we propose the extension of the quality-by-design (QbD) concept to also fit the early development phases of pharmaceuticals by adding elements that are currently widely applied, but not yet included in the QbD model in a structured way. These are the introduction of a 'zero' preformulation phase (i.e., selection of drug substance, possible dosage forms and administration routes based on the evaluated therapeutic need); building in stakeholders' (industry, patient, and regulatory) requirements into the quality target product profile (QTTP); and the use of modern quality management tools during the composition and process design phase [collecting critical quality attributes (CQAs) and selection of CPPs) for (still laboratory-scale) design space (DS) development. Moreover, during industrial scale-up, CQAs (as well as critical process parameters; CPPs) can be changed; however, we recommend that the existing QbD elements are reconsidered and updated after this phase. Copyright © 2018 Elsevier Ltd. All rights reserved.

Fleet Evaluation and Factory Installation of Aerodynamic Heavy Duty Truck Trailers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beck, Jason; Salari, Kambiz; Ortega, Jason

2013-09-30

The purpose of DE-EE0001552 was to develop and deploy a combination of trailer aerodynamic devices and low rolling resistance tires that reduce fuel consumption of a class 8 heavy duty tractor-trailer combination vehicle by 15%. There were 3 phases of the project: Phase 1 – Perform SAE Typed 2 track tests with multiple device combinations. Phase 2 – Conduct a fleet evaluation with selected device combination. Phase 3 – Develop the devices required to manufacture the aerodynamic trailer. All 3 phases have been completed. There is an abundance of available trailer devices on the market, and fleets and owner operatorsmore » have awareness of them and are purchasing them. The products developed in conjunction with this project are at least in their second round of refinement. The fleet test undertaken showed an improvement of 5.5 – 7.8% fuel economy with the devices (This does not include tire contribution).« less

48 CFR 252.235-7003 - Frequency authorization.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Officer during the initial planning, experimental, or developmental phase of contract performance. (c) The... development, production, construction, testing, or operation of a device for which a radio frequency...

48 CFR 252.235-7003 - Frequency authorization.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Officer during the initial planning, experimental, or developmental phase of contract performance. (c) The... development, production, construction, testing, or operation of a device for which a radio frequency...

48 CFR 252.235-7003 - Frequency authorization.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Officer during the initial planning, experimental, or developmental phase of contract performance. (c) The... development, production, construction, testing, or operation of a device for which a radio frequency...

The Development of a Graphical Notation for the Formal Specification of Software

DTIC Science & Technology

1990-12-01

the language. A detailed user survey should be performed after the language implementation is complete to determine the effectiveness of the graphical...productivity. ’Ihere is no better way to improve programmer productivity than to help the programmer to avoid performing the work in the first place. This is...optional prototyping phase is performed ) to develop a computer program (2:40). In 1985, Robert Balzer proposed the program transformation lifecycle

Failures to further developing orphan medicinal products after designation granted in Europe: an analysis of marketing authorisation failures and abandoned drugs.

PubMed

Giannuzzi, Viviana; Landi, Annalisa; Bosone, Enrico; Giannuzzi, Floriana; Nicotri, Stefano; Torrent-Farnell, Josep; Bonifazi, Fedele; Felisi, Mariagrazia; Bonifazi, Donato; Ceci, Adriana

2017-09-11

The research and development process in the field of rare diseases is characterised by many well-known difficulties, and a large percentage of orphan medicinal products do not reach the marketing approval.This work aims at identifying orphan medicinal products that failed the developmental process and investigating reasons for and possible factors influencing failures. Drugs designated in Europe under Regulation (European Commission) 141/2000 in the period 2000-2012 were investigated in terms of the following failures: (1) marketing authorisation failures (refused or withdrawn) and (2) drugs abandoned by sponsors during development.Possible risk factors for failure were analysed using statistically validated methods. This study points out that 437 out of 788 designations are still under development, while 219 failed the developmental process. Among the latter, 34 failed the marketing authorisation process and 185 were abandoned during the developmental process. In the first group of drugs (marketing authorisation failures), 50% reached phase II, 47% reached phase III and 3% reached phase I, while in the second group (abandoned drugs), the majority of orphan medicinal products apparently never started the development process, since no data on 48.1% of them were published and the 3.2% did not progress beyond the non-clinical stage.The reasons for failures of marketing authorisation were: efficacy/safety issues (26), insufficient data (12), quality issues (7), regulatory issues on trials (4) and commercial reasons (1). The main causes for abandoned drugs were efficacy/safety issues (reported in 54 cases), inactive companies (25.4%), change of company strategy (8.1%) and drug competition (10.8%). No information concerning reasons for failure was available for 23.2% of the analysed products. This analysis shows that failures occurred in 27.8% of all designations granted in Europe, the main reasons being safety and efficacy issues. Moreover, the stage of development reached by drugs represents a specific risk factor for failures. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Importance of granulometry on phase evolution and phase-to-phase relationships of experimentally burned impure limestones intended for production of hydraulic lime and/or natural cement

NASA Astrophysics Data System (ADS)

Kozlovcev, Petr; Přikryl, Richard; Přikrylová, Jiřina

2015-04-01

In contrast to modern ordinary Portland cement production from finely ground raw material blends, ancient burning of hydraulic lime was conducted by burning larger pieces of natural raw material. Due to natural variability of raw material composition, exploitation of different beds from even one formation can result the product with significantly different composition and/or properties. Prague basin (Neoproterozoic to pre-Variscan Palaeozoic of the central part of the Bohemian Massif - the so-called Barrandian area, Czech Republic) represents a classical example of the limestone-rich region with long-term history of limestone burning for quick lime and/or various types of hydraulic binders. Due to the fact that burning of natural hydraulic lime has been abandoned in this region at the turn of 19th/20th c., significant gap in knowledge on the behavior of various limestone types and on the influence of minor variance in composition on the quality of burned product is encountered. Moreover, the importance of employment of larger pieces of raw material for burning for the development of proper phase-to-phase relationships (i.e. development of hydraulic phases below sintering temperature at mutual contacts of minerals) has not been examined before. To fill this gap, a representative specimens of major limestone types from the Prague basin have been selected for experimental study: Upper Silurian limestone types (Přídolí and Kopanina Lms.), and Lower Devonian limestones (Radotín, Kotýs, Řeporyje, Dvorce-Prokop, and Zlíchov Lms.). Petrographic character of the experimental material was examined by polarizing microscopy, cathodoluminescence, scanning electron microscopy with an energy dispersive spectrometer (SEM-EDS), and X-ray diffraction (XRD) of insoluble residue. Based on the data from wet silicate analyses, modal composition of studied impure limestones was computed. Experimental raw material was burned in laboratory electric furnace at 1000 and 1200°C for 3 and/or 6 hours. Burned samples were examined by XRD for phase composition and by SEM-EDS for phase-to-phase relationships due to the burning. Based on our data it is evident that larnite-belite (dicalcium-silicate) is dominant phase in burned silica-rich limestones (represented by e.g. Dvorce-Prokop, Přídolí and/or Kopanina Lms.). In clay-rich limestones containing kaolinite and illite, gehlenite and other calcium aluminates and aluminosilicates were detected (represented by Kosoř, Řeporyje, and/or a portion of Dvorce-Prokop Lms.). Due to higher proportion of Fe-oxihydroxides in the Řeporyje Lms., brownmillerite (calcium aluminoferrite) forms as a typical minor phases during burning. Free-lime (plus its hydrated form - portlandite) makes dominant phase in limestones exhibiting low non-carbonate admixture (Kotýs and/or a portion of Kopanina Lms.). These results clearly demonstrate that presence of certain non-carbonate minerals governs formation of certain hydraulic phases in burned product, whilst mutual proportions of individual minerals in raw materials influence amount of newly formed phases.

Thermodynamic assessment of the U–La–O system

DOE PAGES

McMurray, J. W.; Shin, D.; Besmann, T. M.

2014-10-03

The CALPHAD methodology was used to develop a thermodynamic assessment of the U-La-O system. The solid solution and liquid phases are described with the compound energy formalism and the partially ionic two-sublattice liquid model respectively. A density functional theory (DFT) calculation for the lattice stability of the fictive lanthanum oxide fluorite structure compound is used to determine the Gibbs energies for the La containing end-members in the CEF model for U 1-yLa yO 2+x. Experimental thermodynamic and phase equilibria data were then used in optimizations to develop representations of the phases in the system that can be extended to includemore » other actinide and fission products to develop multi-component models. The models that comprise this assessment very well reproduce experimentally determined oxygen potentials and the observed phase relations for the U-La-O system.« less

Prediction of the Hydrogen Peroxide-Induced Methionine Oxidation Propensity in Monoclonal Antibodies.

PubMed

Agrawal, Neeraj J; Dykstra, Andrew; Yang, Jane; Yue, Hai; Nguyen, Xichdao; Kolvenbach, Carl; Angell, Nicolas

2018-05-01

Methionine oxidation in therapeutic antibodies can impact the product's stability, clinical efficacy, and safety and hence it is desirable to address the methionine oxidation liability during antibody discovery and development phase. Although the current experimental approaches can identify the oxidation-labile methionine residues, their application is limited mostly to the development phase. We demonstrate an in silico method that can be used to predict oxidation-labile residues based solely on the antibody sequence and structure information. Since antibody sequence information is available in the discovery phase, the in silico method can be applied very early on to identify the oxidation-labile methionine residues and subsequently address the oxidation liability. We believe that the in silico method for methionine oxidation liability assessment can aid in antibody discovery and development phase to address the liability in a more rational way. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Inflow performance relationship for perforated wells producing from solution gas drive reservoir

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sukarno, P.; Tobing, E.L.

1995-10-01

The IPR curve equations, which are available today, are developed for open hole wells. In the application of Nodal System Analysis in perforated wells, an accurate calculation of pressure loss in the perforation is very important. Nowadays, the equation which is widely used is Blount, Jones and Glaze equation, to estimate pressure loss across perforation. This equation is derived for single phase flow, either oil or gas, therefore it is not suitable for two-phase production wells. In this paper, an IPR curve equation for perforated wells, producing from solution gas drive reservoir, is introduced. The equation has been developed usingmore » two phase single well simulator combine to two phase flow in perforation equation, derived by Perez and Kelkar. A wide range of reservoir rock and fluid properties and perforation geometry are used to develop the equation statistically.« less

Rectal Microbicide Development

PubMed Central

Dezzutti, Charlene

2014-01-01

The last few years have seen important progress in demonstrating the efficacy of oral pre-exposure prophylaxis, vaginal microbicides, and treatment as prevention as effective strategies for reducing the risk of acquiring or transmitting HIV infection. There has also been significant progress in the development of rectal microbicides. Preclinical non-human primate studies have demonstrated that antiretroviral microbicides can provide significant protection from rectal challenge with SIV or SHIV. Recent Phase 1 rectal microbicide studies have characterized the safety, acceptability, compartmental pharmacokinetics (PK), and pharmaco-dynamics (PD) of both UC781 and tenofovir gels. The tenofovir gel formulation used in vaginal studies was not well tolerated in the rectum and newer rectal-specific formulations have been developed and evaluated in Phase 1 studies. The PK/PD data generated in these Phase 1 studies may reduce the risk of advancing ineffective candidate rectal microbicides into late stage development. Tenofovir gel is currently poised to move into Phase 2 evaluation and it is possible that a Phase 2B/3 effectiveness study with this product could be initiated in the next 2–3 years. PMID:23612991

Design and simulation of ion optics for ion sources for production of singly charged ions

NASA Astrophysics Data System (ADS)

Zelenak, A.; Bogomolov, S. L.

2004-05-01

During the last 2 years different types of the singly charged ion sources were developed for FLNR (JINR) new projects such as Dubna radioactive ion beams, (Phase I and Phase II), the production of the tritium ion beam and the MASHA mass separator. The ion optics simulations for 2.45 GHz electron cyclotron resonance source, rf source, and the plasma ion source were performed. In this article the design and simulation results of the optics of new ion sources are presented. The results of simulation are compared with measurements obtained during the experiments.

Materials Compatibility and Agent Operational Validation for Halon 1211 Replacement: Phases 1 2, and 3. Volume 1

DTIC Science & Technology

1993-03-01

KC-135 Gl-epoxy Winglet 1 *1 = experimental; 2 = prototype development; 3 = production 9 TABLE 3. ADVANCED COMPOSITES IN MILITARY AIRCRAFT (CONCLUDED...specially blended for related agent testing and would not be available, due to its high production cost, for regular distribution.1 ’Personal

Fast demodulation of pattern images by spiral phase transform in structured-illumination reflectance imaging for detection of bruises in apples

USDA-ARS?s Scientific Manuscript database

A structured-illumination reflectance imaging (SIRI) system was recently developed in our laboratory for enhanced quality evaluation of horticultural products. It was implemented using a digital camera to acquire reflectance images from food products subjected to sinusoidal patterns (or other simila...

Monitoring pathogens from irradiated agriculture products

NASA Astrophysics Data System (ADS)

Butterweck, Joseph S.

The final food and environmental safety assessment of agriculture product irradiation can only be determined by product history. Product history will be used for future research and development, regulations, commercial practices and implementation of agriculture and food irradiation on a regional basis. The commercial irradiator treats large varieties and amounts of products that are used in various environments. It, in time, will generate a large data base of product history. Field product monitoring begins when food irradiation progresses from the pilot/demonstration phase to the commercial phase. At that time, it is important that there be in place a monitoring system to collect and analyze field data. The systems managers, public health authorities and exotic disease specialists will use this information to assess the reduction of food pathogens on the populace and the environment. The common sources of monitoring data are as follows: 1) Host Monitoring a) Medical Diagnosis b) Autopsy c) Serology Surveys 2) Environmental Monitoring a) Sentinel b) Pest Surveys/Microbial Counts c) Sanitary Inspections 3) Food Industries Quality Assurance Monitoring a) End Product Inspection b) Complaints c) Continual Use of the Product

Novel chromatographic separation and carbon solid-phase extraction of acetanilide herbicide degradation products.

PubMed

Shoemaker, Jody A

2002-01-01

One acetamide and 5 acetanilide herbicides are currently registered for use in the United States. Over the past several years, ethanesulfonic acid (ESA) and oxanilic acid (OA) degradation products of these acetanilide/acetamide herbicides have been found in U.S. ground waters and surface waters. Alachlor ESA and other acetanilide degradation products are listed on the U.S. Environmental Protection Agency's (EPA) 1998 Drinking Water Contaminant Candidate List. Consequently, EPA is interested in obtaining national occurrence data for these contaminants in drinking water. EPA currently does not have a method for determining these acetanilide degradation products in drinking water; therefore, a research method is being developed using liquid chromatography/negative ion electrospray/mass spectrometry with solid-phase extraction (SPE). A novel chromatographic separation of the acetochlor/alachlor ESA and OA structural isomers was developed which uses an ammonium acetate-methanol gradient combined with heating the analytical column to 70 degrees C. Twelve acetanilide degradates were extracted by SPE from 100 mL water samples using carbon cartridges with mean recoveries >90% and relative standard deviations < or =16%.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Childers, M.; Barnes, J.

The phased field development of the Lion and Panthere fields, offshore the Ivory Coast, includes a small floating production, storage, and offloading (FPSO) tanker with minimal processing capability as an early oil production system (EPS). For the long-term production scheme, the FPSO will be replaced by a converted jack up mobile offshore production system (MOPS) with full process equipment. The development also includes guyed-caisson well platforms, pipeline export for natural gas to fuel an onshore power plant, and a floating storage and offloading (FSO) tanker for oil export. Pipeline export for oil is a future possibility. This array of innovativemore » strategies and techniques seldom has been brought together in a single project. The paper describes the development plan, early oil, jack up MOPS, and transport and installation.« less

A genetic switch controls the production of flagella and toxins in Clostridium difficile.

PubMed

Anjuwon-Foster, Brandon R; Tamayo, Rita

2017-03-01

In the human intestinal pathogen Clostridium difficile, flagella promote adherence to intestinal epithelial cells. Flagellar gene expression also indirectly impacts production of the glucosylating toxins, which are essential to diarrheal disease development. Thus, factors that regulate the expression of the flgB operon will likely impact toxin production in addition to flagellar motility. Here, we report the identification a "flagellar switch" that controls the phase variable production of flagella and glucosylating toxins. The flagellar switch, located upstream of the flgB operon containing the early stage flagellar genes, is a 154 bp invertible sequence flanked by 21 bp inverted repeats. Bacteria with the sequence in one orientation expressed flagellum and toxin genes, produced flagella, and secreted the toxins ("flg phase ON"). Bacteria with the sequence in the inverse orientation were attenuated for flagellar and toxin gene expression, were aflagellate, and showed decreased toxin secretion ("flg phase OFF"). The orientation of the flagellar switch is reversible during growth in vitro. We provide evidence that gene regulation via the flagellar switch occurs post-transcription initiation and requires a C. difficile-specific regulatory factor to destabilize or degrade the early flagellar gene mRNA when the flagellar switch is in the OFF orientation. Lastly, through mutagenesis and characterization of flagellar phase locked isolates, we determined that the tyrosine recombinase RecV, which catalyzes inversion at the cwpV switch, is also responsible for inversion at the flagellar switch in both directions. Phase variable flagellar motility and toxin production suggests that these important virulence factors have both advantageous and detrimental effects during the course of infection.

Unlocking the potential of supported liquid phase catalysts with supercritical fluids: low temperature continuous flow catalysis with integrated product separation

PubMed Central

Franciò, Giancarlo; Hintermair, Ulrich; Leitner, Walter

2015-01-01

Solution-phase catalysis using molecular transition metal complexes is an extremely powerful tool for chemical synthesis and a key technology for sustainable manufacturing. However, as the reaction complexity and thermal sensitivity of the catalytic system increase, engineering challenges associated with product separation and catalyst recovery can override the value of the product. This persistent downstream issue often renders industrial exploitation of homogeneous catalysis uneconomical despite impressive batch performance of the catalyst. In this regard, continuous-flow systems that allow steady-state homogeneous turnover in a stationary liquid phase while at the same time effecting integrated product separation at mild process temperatures represent a particularly attractive scenario. While continuous-flow processing is a standard procedure for large volume manufacturing, capitalizing on its potential in the realm of the molecular complexity of organic synthesis is still an emerging area that requires innovative solutions. Here we highlight some recent developments which have succeeded in realizing such systems by the combination of near- and supercritical fluids with homogeneous catalysts in supported liquid phases. The cases discussed exemplify how all three levels of continuous-flow homogeneous catalysis (catalyst system, separation strategy, process scheme) must be matched to locate viable process conditions. PMID:26574523

Unlocking the potential of supported liquid phase catalysts with supercritical fluids: low temperature continuous flow catalysis with integrated product separation.

PubMed

Franciò, Giancarlo; Hintermair, Ulrich; Leitner, Walter

2015-12-28

Solution-phase catalysis using molecular transition metal complexes is an extremely powerful tool for chemical synthesis and a key technology for sustainable manufacturing. However, as the reaction complexity and thermal sensitivity of the catalytic system increase, engineering challenges associated with product separation and catalyst recovery can override the value of the product. This persistent downstream issue often renders industrial exploitation of homogeneous catalysis uneconomical despite impressive batch performance of the catalyst. In this regard, continuous-flow systems that allow steady-state homogeneous turnover in a stationary liquid phase while at the same time effecting integrated product separation at mild process temperatures represent a particularly attractive scenario. While continuous-flow processing is a standard procedure for large volume manufacturing, capitalizing on its potential in the realm of the molecular complexity of organic synthesis is still an emerging area that requires innovative solutions. Here we highlight some recent developments which have succeeded in realizing such systems by the combination of near- and supercritical fluids with homogeneous catalysts in supported liquid phases. The cases discussed exemplify how all three levels of continuous-flow homogeneous catalysis (catalyst system, separation strategy, process scheme) must be matched to locate viable process conditions. © 2015 The Authors.

Development of a perfusion reversed-phase high performance liquid chromatography method for the characterisation of maize products using multivariate analysis.

PubMed

Rodriguez-Nogales, J M; Garcia, M C; Marina, M L

2006-02-03

A perfusion reversed-phase high performance liquid chromatography (RP-HPLC) method has been designed to allow rapid (3.4 min) separations of maize proteins with high resolution. Several factors, such as extraction conditions, temperature, detection wavelength and type and concentration of ion-pairing agent were optimised. A fine optimisation of the gradient elution was also performed by applying experimental design. Commercial maize products for human consumption (flours, precocked flours, fried snacks and extruded snacks) were characterised for the first time by perfusion RP-HPLC and their chromatographic profiles allowed a differentiation among products relating the different technological process used for their preparation. Furthermore, applying discriminant analysis makes it possible to group the samples according with the technological process suffered by maize products, obtaining a good prediction in 92% of the samples.

Basic Skills Resource Center. Part 2

DTIC Science & Technology

1985-05-01

side if neceseary and Identify by block number) Basic Skills Education Curriculum Development Learning Strategies Reading Comprehension Motivational ... Motivational Skills Training for Military Technical Training Students ...... Barbara L. McCombs 25 Problem 27 Purpose 27 Approach 28 - Phase 1 28 - Phase...and Learning ...... John J. Hedl , Jr. 53 Purpose of Project 55 Description of Work 55 V Products 56 Virtual Videodisc Software Requirements ...... J.D

A Taxonomy of Factors to Promote Quality Web-Supported Learning

ERIC Educational Resources Information Center

Fresen, Jill

2007-01-01

This article reports on a case study of the e-learning production unit at the University of Pretoria, South Africa. Phase 1 of the study, completed in 2003, was the design and development of a process-based quality management system for web-supported learning (WSL) using a basic ISO 9000 approach (University of Pretoria, 2003). The second phase,…

Automated Estimation Of Software-Development Costs

NASA Technical Reports Server (NTRS)

Roush, George B.; Reini, William

1993-01-01

COSTMODL is automated software development-estimation tool. Yields significant reduction in risk of cost overruns and failed projects. Accepts description of software product developed and computes estimates of effort required to produce it, calendar schedule required, and distribution of effort and staffing as function of defined set of development life-cycle phases. Written for IBM PC(R)-compatible computers.

Atom Core Interactive Electronic Book to Develop Self Efficacy and Critical Thinking Skills

ERIC Educational Resources Information Center

Pradina, Luthfia Puspa; Suyatna, Agus

2018-01-01

The purpose of this research is to develop interactive atomic electronic school book (IESB) to cultivate critical thinking skills and confidence of students grade 12. The method used in this research was the ADDIE (Analyze Design Development Implementation Evaluation) development procedure which is limited to the test phase of product design…

Phase retrieval from local measurements in two dimensions

NASA Astrophysics Data System (ADS)

Iwen, Mark; Preskitt, Brian; Saab, Rayan; Viswanathan, Aditya

2017-08-01

The phase retrieval problem has appeared in a multitude of applications for decades. While ad hoc solutions have existed since the early 1970s, recent developments have provided algorithms that offer promising theoretical guarantees under increasingly realistic assumptions. Motivated by ptychographic imaging, we generalize a recent result on phase retrieval of a one dimensional objective vector x ∈ ℂd to recover a two dimensional sample Q ∈ ℂd x d from phaseless measurements, using a tensor product formulation to extend the previous work.

Model-Informed Drug Development for Ixazomib, an Oral Proteasome Inhibitor.

PubMed

Gupta, Neeraj; Hanley, Michael J; Diderichsen, Paul M; Yang, Huyuan; Ke, Alice; Teng, Zhaoyang; Labotka, Richard; Berg, Deborah; Patel, Chirag; Liu, Guohui; van de Velde, Helgi; Venkatakrishnan, Karthik

2018-02-15

Model-informed drug development (MIDD) was central to the development of the oral proteasome inhibitor ixazomib, facilitating internal decisions (switch from body surface area (BSA)-based to fixed dosing, inclusive phase III trials, portfolio prioritization of ixazomib-based combinations, phase III dose for maintenance treatment), regulatory review (model-informed QT analysis, benefit-risk of 4 mg dose), and product labeling (absolute bioavailability and intrinsic/extrinsic factors). This review discusses the impact of MIDD in enabling patient-centric therapeutic optimization during the development of ixazomib. © 2017 The Authors. Clinical Pharmacology & Therapeutics published by Wiley Periodicals, Inc. on behalf of American Society for Clinical Pharmacology and Therapeutics.

Valorization of lubricant-based wastewater for bacterial neutral lipids production: Growth-linked biosynthesis.

PubMed

Da Silva, Pedro D M P; Lima, Filipa; Alves, Maria Madalena; Bijmans, Martijn F M; Pereira, Maria Alcina

2016-09-15

Lipids produced by microorganisms are currently of great interest as raw material for either biofuels or oleochemicals production. Significant biosynthesis of neutral lipids, such as triacylglycerol (TAG) and wax esters (WE) are thought to be limited to a few strains. Hydrocarbonoclastic bacteria (HCB), key players in bioremediation of hydrocarbon contaminated ecosystems, are among this group of strains. Hydrocarbon rich wastewaters have been overlooked concerning their potential as raw material for microbial lipids production. In this study, lubricant-based wastewater was fed, as sole carbon source, to two HCB representative wild strains: Alcanivorax borkumensis SK2, and Rhodococcus opacus PD630. Neutral lipid production was observed with both strains cultivated under uncontrolled conditions of pH and dissolved oxygen. A. borkumensis SK2 was further investigated in a pH- and OD-controlled fermenter. Different phases were assessed separately in terms of lipids production and alkanes removal. The maximum TAG production rate occurred during stationary phase (4 mg-TAG/L h). The maximum production rate of WE-like compounds was 15 mg/L h, and was observed during exponential growth phase. Hydrocarbons removal was 97% of the gas chromatography (GC) resolved straight-chain alkanes. The maximum removal rate was observed during exponential growth phase (6 mg-alkanes/L h). This investigation proposes a novel approach for the management of lubricant waste oil, aiming at its conversion into valuable lipids. The feasibility of the concept is demonstrated under low salt (0.3%) and saline (3.3%) conditions, and presents clues for its technological development, since growth associated oil production opens the possibility for establishing continuous fermentation processes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Performance Testing of the Vapor Phase Catalytic Ammonia Removal Engineering Development Unit

NASA Technical Reports Server (NTRS)

Flynn, Michael; Tleimat, Maher; Nalette, Tim; Quinn, Gregory

2005-01-01

This paper describes the results of performance testing of the Vapor Phase Catalytic Ammonia Removal (VPCAR) technology. The VPCAR technology is currently being developed by NASA as a Mars transit vehicle water recycling system. NASA has recently completed-a grant-to develop a next generation VPCAR system. This grant concluded with the shipment of the final deliverable to NASA on 8/31/03. This paper presents the results of mass, power, volume, and acoustic measurements for the delivered system. Product water purity analysis for a Mars transit mission and a simulated planetary base wastewater ersatz are also provided.

Space Station Human Factors Research Review. Volume 1: EVA Research and Development

NASA Technical Reports Server (NTRS)

Cohen, Marc M. (Editor); Vykukal, H. C. (Editor)

1988-01-01

An overview is presented of extravehicular activity (EVA) research and development activities at Ames. The majority of the program was devoted to presentations by the three contractors working in parallel on the EVA System Phase A Study, focusing on Implications for Man-Systems Design. Overhead visuals are included for a mission results summary, space station EVA requirements and interface accommodations summary, human productivity study cross-task coordination, and advanced EVAS Phase A study implications for man-systems design. Articles are also included on subsea approach to work systems development and advanced EVA system design requirements.

On the phase lag of turbulent dissipation in rotating tidal flows

NASA Astrophysics Data System (ADS)

Zhang, Qianjiang; Wu, Jiaxue

2018-03-01

Field observations of rotating tidal flows in a shallow tidally swept sea reveal that a notable phase lag of both shear production and turbulent dissipation increases with height above the seafloor. These vertical delays of turbulent quantities are approximately equivalent in magnitude to that of squared mean shear. The shear production approximately equals turbulent dissipation over the phase-lag column, and thus a main mechanism of phase lag of dissipation is mean shear, rather than vertical diffusion of turbulent kinetic energy. By relating the phase lag of dissipation to that of the mean shear, a simple formulation with constant eddy viscosity is developed to describe the phase lag in rotating tidal flows. An analytical solution indicates that the phase lag increases linearly with height subjected to a combined effect of tidal frequency, Coriolis parameter and eddy viscosity. The vertical diffusion of momentum associated with eddy viscosity produces the phase lag of squared mean shear, and resultant delay of turbulent quantities. Its magnitude is inhibited by Earth's rotation. Furthermore, a theoretical formulation of the phase lag with a parabolic eddy viscosity profile can be constructed. A first-order approximation of this formulation is still a linear function of height, and its magnitude is approximately 0.8 times that with constant viscosity. Finally, the theoretical solutions of phase lag with realistic viscosity can be satisfactorily justified by realistic phase lags of dissipation.

Success rates for product development strategies in new drug development.

PubMed

Dahlin, E; Nelson, G M; Haynes, M; Sargeant, F

2016-04-01

While research has examined the likelihood that drugs progress across phases of clinical trials, no research to date has examined the types of product development strategies that are the most likely to be successful in clinical trials. This research seeks to identify the strategies that are most likely to reach the market-those generated using a novel product development strategy or strategies that combine a company's expertise with both drugs and indications, which we call combined experience strategies. We evaluate the success of product development strategies in the drug development process for a sample of 2562 clinical trials completed by 406 US pharmaceutical companies. To identify product development strategies, we coded each clinical trial according to whether it consisted of an indication or a drug that was new to the firm. Accordingly, a clinical trial that consists of both an indication and a drug that were both new to the firm represents a novel product development strategy; indication experience is a product development strategy that consists of an indication that a firm had tested previously in a clinical trial, but with a drug that was new to the firm; drug experience is a product development strategy that consists of a drug that the firm had prior experience testing in clinical trials, but with an indication that was new to the firm; combined experience consists of both a drug and an indication that the firm had experience testing in clinical trials. Success rates for product development strategies across clinical phases were calculated for the clinical trials in our sample. Combined experience strategies had the highest success rate. More than three and a half percent (0·036) of the trials that combined experience with drugs and indications eventually reached the market. The next most successful strategy is drug experience (0·025) with novel strategies trailing closely (0·024). Indication experience strategies are the least successful (0·008). These differences are statistically significant. The primary contribution of this study is that product development strategies combining experience with drugs and indications strategies are the most likely to reach the market, even though they are least common strategy. Therefore, combined experience strategies remain underutilized. The findings also suggest a promising path for pursuing combined experience strategies: gaining expertise with drugs is likely to be a more effective path to gaining the expertise necessary for developing subsequent recombination strategies. © 2016 John Wiley & Sons Ltd.

Characteristics of solidified products containing radioactive molten salt waste.

PubMed

Park, Hwan-Seo; Kim, In-Tae; Cho, Yong-Zun; Eun, Hee-Chul; Kim, Joon-Hyung

2007-11-01

The molten salt waste from a pyroprocess to recover uranium and transuranic elements is one of the problematic radioactive wastes to be solidified into a durable wasteform for its final disposal. By using a novel method, named as the GRSS (gel-route stabilization/solidification) method, a molten salt waste was treated to produce a unique wasteform. A borosilicate glass as a chemical binder dissolves the silicate compounds in the gel products to produce one amorphous phase while most of the phosphates are encapsulated by the vitrified phase. Also, Cs in the gel product is preferentially situated in the silicate phase, and it is vitrified into a glassy phase after a heat treatment. The Sr-containing phase is mainly phosphate compounds and encapsulated by the glassy phase. These phenomena could be identified by the static and dynamic leaching test that revealed a high leach resistance of radionuclides. The leach rates were about 10(-3) - 10(-2) g/m2 x day for Cs and 10(-4) - 10(-3) g/m2 x day for Sr, and the leached fractions of them were predicted to be 0.89% and 0.39% at 900 days, respectively. This paper describes the characteristics of a unique wasteform containing a molten salt waste and provides important information on a newly developed immobilization technology for salt wastes, the GRSS method.

Rubidium frequency standard test program for NAVSTAR GPS

NASA Technical Reports Server (NTRS)

Koide, F.; Dederich, D. J.

1978-01-01

Test data of the RFS Program in the Production phase and computer automation are presented, as an essential element in the evaluation of the RFS performance in a simulated spacecraft environment. Typical production test data will be discussed for stabilities from 1 to 100,000 seconds averaging time and simulated time error accumulation test. Also, design considerations in developing the RFS test systems for the acceptance test in production are discussed.

East Europe Report

DTIC Science & Technology

1986-08-27

notions of large, medium-sized and small business and of the need to achieve a more just distribution of productive forces. This policy is necessary...element that could complement and raise the effectiveness of the large-scale production that is characteristic of the present phase of development of... productive forces in socialist society. To understand fully the significance of this party demand, we would have to recall that, in his speech at the

Preparation and characterization of two new forced degradation products of letrozole and development of a stability-indicating RP-LC method for its determination.

PubMed

Elkady, Ehab Farouk; Fouad, Marwa Ahmed

2015-11-01

Two new hydrolytic products of letrozole were identified and proved to be true degradation products obtained by alkaline and acidic degradation of the drug. The acid and amide forms of the nitrile groups of letrozole were prepared and identified by IR and mass spectroscopic techniques. Subsequently, a simple, precise and selective stability-indicating RPLC method was developed and validated for the determination of letrozole in the presence of its degradation products. Letrozole was subjected to alkali and acid hydrolysis, oxidation, thermal degradation and photo-degradation. The degradation products were well isolated from letrozole. The chromatographic method was achieved using gradient elution of the drug and its degradation products on a reversed phase Zorbax Eclipse C18 column (100mm x 4.6mm, 3.5 μm) using a mobile phase consisting of 0.01M KH₂PO₄and methanol at a flow rate of 1 mL min⁻¹. Quantitation was achieved with UV detection at 230 nm. Linearity, accuracy and precision were found to be acceptable over the concentration range of 0.01-80 μgmL⁻¹. The proposed method was successfully applied to the determination of letrozole in bulk, plasma and in its pharmaceutical preparation.

A psychological approach to providing self-management education for people with type 2 diabetes: the Diabetes Manual

PubMed Central

Sturt, Jackie; Taylor, Hafrun; Docherty, Andrea; Dale, Jeremy; Louise, Taylor

2006-01-01

Background The objectives of this study were twofold (i) to develop the Diabetes Manual, a self-management educational intervention aimed at improving biomedical and psychosocial outcomes (ii) to produce early phase evidence relating to validity and clinical feasibility to inform future research and systematic reviews. Methods Using the UK Medical Research Council's complex intervention framework, the Diabetes Manual and associated self management interventions were developed through pre-clinical, and phase I evaluation phases guided by adult-learning and self-efficacy theories, clinical feasibility and health policy protocols. A qualitative needs assessment and an RCT contributed data to the pre-clinical phase. Phase I incorporated intervention development informed by the pre-clinical phase and a feasibility survey. Results The pre-clinical and phase I studies resulted in the production in the Diabetes Manual programme for trial evaluation as delivered within routine primary care consultations. Conclusion This complex intervention shows early feasibility and face validity for both diabetes health professionals and people with diabetes. Randomised trial will determine effectiveness against clinical and psychological outcomes. Further study of some component parts, delivered in alternative combinations, is recommended. PMID:17129376

Additional EIPC Study Analysis: Interim Report on High Priority Topics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hadley, Stanton W

Between 2010 and 2012 the Eastern Interconnection Planning Collaborative (EIPC) conducted a major long-term resource and transmission study of the Eastern Interconnection (EI). With guidance from a Stakeholder Steering Committee (SSC) that included representatives from the Eastern Interconnection States Planning Council (EISPC) among others, the project was conducted in two phases. Phase 1 involved a long-term capacity expansion analysis that involved creation of eight major futures plus 72 sensitivities. Three scenarios were selected for more extensive transmission- focused evaluation in Phase 2. Five power flow analyses, nine production cost model runs (including six sensitivities), and three capital cost estimations weremore » developed during this second phase. The results from Phase 1 and 2 provided a wealth of data that could be examined further to address energy-related questions. A list of 13 topics was developed for further analysis; this paper discusses the first five.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

William C. Maurer; William J. McDonald; Thomas E. Williams

Underbalanced drilling is experiencing growth at a rate that rivals that of horizontal drilling in the mid-1980s and coiled-tubing drilling in the 1990s. Problems remain, however, for applying underbalanced drilling in a wider range of geological settings and drilling environments. This report addresses developments under this DOE project to develop products aimed at overcoming these problems. During Phase I of the DOE project, market analyses showed that up to 12,000 wells per year (i.e., 30% of all wells) will be drilled underbalanced in the U.S.A. within the next ten years. A user-friendly foam fluid hydraulics model (FOAM) was developed formore » a PC Windows environment during Phase I. FOAM predicts circulating pressures and flow characteristics of foam fluids used in underbalanced drilling operations. FOAM is based on the best available mathematical models, and was validated through comparison to existing models, laboratory test data and field data. This model does not handle two-phase flow or air and mist drilling where the foam quality is above 0.97. This FOAM model was greatly expanded during Phase II including adding an improved foam rheological model and a ''matching'' feature that allows the model to be field calibrated. During Phase I, a lightweight drilling fluid was developed that uses hollow glass spheres (HGS) to reduce the density of the mud to less than that of water. HGS fluids have several advantages over aerated fluids, including they are incompressible, they reduce corrosion and vibration problems, they allow the use of mud-pulse MWD tools, and they eliminate high compressor and nitrogen costs. Phase II tests showed that HGS significantly reduce formation damage with water-based drilling and completion fluids and thereby potentially can increase oil and gas production in wells drilled with water-based fluids. Extensive rheological testing was conducted with HGS drilling and completion fluids during Phase II. These tests showed that the HGS fluids act similarly to conventional fluids and that they have potential application in many areas, including underbalanced drilling, completions, and riserless drilling. Early field tests under this project are encouraging. These led to limited tests by industry (which are also described). Further field tests and cost analyses are needed to demonstrate the viability of HGS fluids in different applications. Once their effectiveness is demonstrated, they should find widespread application and should significantly reduce drilling costs and increase oil and gas production rates. A number of important oilfield applications for HGS outside of Underbalanced Drilling were identified. One of these--Dual Gradient Drilling (DGD) for deepwater exploration and development--is very promising. Investigative work on DGD under the project is reported, along with definition of a large joint-industry project resulting from the work. Other innovative products/applications are highlighted in the report including the use of HGS as a cement additive.« less

Precambrian perspectives.

PubMed

Goodwin, A M

1981-07-03

The Precambrian record is interpreted in terms of an evolutionary progression that moves in the direction of increasing continental stability. An early, highly mobile microplate tectonics phase progressed through a more stable, largely intracratonic, ensialic, mobile belt phase to the modern macroplate tectonics phase that involves large, rigid lithospheric plates. Various phases are characterized by distinctive crustal associations. Three controls-bulk earth heat production, crustal fractionation and cratonization, and atmospheric oxygen accumulation-are viewed as the cumulative cause of the trends and events that characterize the crust at different stages of development, from its inception approximately 4.6 billion years ago to the present.

The clinical trials supporting benzyl alcohol lotion 5% (Ulesfia): a safe and effective topical treatment for head lice (pediculosis humanus capitis).

PubMed

Meinking, Terri L; Villar, Maria E; Vicaria, Maureen; Eyerdam, Debbie H; Paquet, Diane; Mertz-Rivera, Kamara; Rivera, Hector F; Hiriart, Javier; Reyna, Susan

2010-01-01

Benzyl alcohol lotion 5% (BAL 5%) is a non-neurotoxic topical head lice treatment that is safe and effective in children as young as 6 months of age. The safety and efficacy of this pediculicide has been studied in 695 (confirm number) subjects in all phases of clinical development. Scanning electron micrographs (SEM) demonstrated that the active agent appears to stun the breathing spiracles open, enabling the vehicle to penetrate the respiratory mechanism (spiracles), therefore asphyxiating the lice. Initial phase II trials compared this novel product to RID using identical volumes of treatment (4 oz/application) and yielding, almost, identical efficacy. This outcome pointed to the significant importance of completely saturating the hair with the product in order to achieve maximum treatment success. A second phase II trial, which allowed the use of sufficient product to saturate the hair, resulted in 100% efficacy after both 10 and 30 minute treatments. A third phase II trial verified an effective dose. Phase III trials compared BAL 5% to vehicle placebo for two 10-minute applications. It proved to be safe and effective (p < 0.001) for treatment of head lice and is the first FDA-approved non-neurotoxic lice treatment, now available in the United States as Ulesfia lotion.

A systems approach to computer-based training

NASA Technical Reports Server (NTRS)

Drape, Gaylen W.

1994-01-01

This paper describes the hardware and software systems approach used in the Automated Recertification Training System (ARTS), a Phase 2 Small Business Innovation Research (SBIR) project for NASA Kennedy Space Center (KSC). The goal of this project is to optimize recertification training of technicians who process the Space Shuttle before launch by providing computer-based training courseware. The objectives of ARTS are to implement more effective CBT applications identified through a need assessment process and to provide an ehanced courseware production system. The system's capabilities are demonstrated by using five different pilot applications to convert existing classroom courses into interactive courseware. When the system is fully implemented at NASA/KSC, trainee job performance will improve and the cost of courseware development will be lower. Commercialization of the technology developed as part of this SBIR project is planned for Phase 3. Anticipated spin-off products include custom courseware for technical skills training and courseware production software for use by corporate training organizations of aerospace and other industrial companies.

Nano-Magnets and Additive Manufacturing for Electric Motors

NASA Technical Reports Server (NTRS)

Misra, Ajay K.

2014-01-01

High power density is required for application of electric motors in hybrid electric propulsion. Potential path to achieve high power density in electric motors include advanced materials, lightweight thermal management, lightweight structural concepts, high power density power electronics, and advanced manufacturing. This presentation will focus on two key technologies for achieving high power density, advanced magnets and additive manufacturing. The maximum energy product in current magnets is reaching their theoretical limits as a result of material and process improvements. Future improvements in the maximum energy product for magnets can be achieved through development of nanocomposite magnets combining the hard magnetic phase and soft magnetic phase at the nanoscale level. The presentation will provide an overview of the current state of development for nanocomposite magnets and the future path for doubling the maximum energy product. The other part of the presentation will focus on the role of additive manufacturing in fabrication of high power density electric motors. The presentation will highlight the potential opportunities for applying additive manufacturing to fabricate electric motors.

Assay of common sunscreen agents in suncare products by high-performance liquid chromatography on a cyanopropyl-bonded silica column.

PubMed

Simeoni, Silvia; Tursilli, Rosanna; Bianchi, Anna; Scalia, Santo

2005-06-15

A rapid high-performance liquid chromatographic method was developed for the simultaneous assay of eight of the most common sunscreen agents (octyl-methoxycinnamate, oxybenzone, butyl-methoxydibenzoylmethane, octyl-salicilate, methylbenzylidene camphor, octyl-dimethylamminobenzoate, phenylbenzimidazole sulphonic acid and octocrylene) in sun protection products. Evaluation of the influence of different stationary phases and eluents on the separation selectivity showed that optimal resolution was obtained on a cyanopropyl-silica column eluted with methanol-acetonitrile-tetrahydrofuran-aqueous acetic acid. A small adjustment of the proposed chromatographic system (reduction in the aqueous content of the mobile phase) permitted also the determination of the extremely hydrophobic UV filter, methylene bis-benzotriazolyl tetramethylbutylphenol along with three other sunscreen agents, octyl-methoxycinnamate, oxybenzone, butyl-methoxydibenzoylmethane. Recoveries of the UV filters from the spiked formulation were between 95.7 and 103.7% and the precision of the method was better than 6.1% relative standard deviation. The developed HPLC procedure is suitable for quality control and photostability analyses of commercial suncare products.

Evolution of the research collaboration network in a productive department.

PubMed

Katerndahl, David

2012-02-01

Understanding collaboration networks can facilitate the research growth of new or developing departments. The purpose of this study was to use social network analysis to understand how the research collaboration network evolved within a productive department. Over a 13-year period, a departmental faculty completed an annual survey describing their research collaborations. Data were analyzed using social network analysis. Network measures focused on connectedness, distance, groupings and heterogeneity of distribution, while measures for the research director and external collaboration focused on centrality and roles within the network. Longitudinal patterns of network collaboration were assessed using Simulation Investigation for Empirical Network Analysis software (University of Groningen, Groningen, Netherlands). Based upon the number of active research projects, research development can be divided into three phases. The initial development phase was characterized by increasing centralization and collaboration focused within a single subject area. During the maintenance phase, measures went through cycles, possibly because of changes in faculty composition. While the research director was not a 'key player' within the network during the first several years, external collaboration played a central role during all phases. Longitudinal analysis found that forming ties was more likely when the opportunity for network closure existed and when those around you are principal investigators (PIs). Initial development of research relied heavily upon a centralized network involving external collaboration; a central position of the research director during research development was not important. Changes in collaboration depended upon faculty gender and tenure track as well as transitivity and the 'popularity of PIs'. © 2011 Blackwell Publishing Ltd.

Design requirements for SRB production control system. Volume 4: Implementation

NASA Technical Reports Server (NTRS)

1981-01-01

The implementation plan which is presented was developed to provide the means for the successful implementation of the automated production control system. There are three factors which the implementation plan encompasses: detailed planning; phased implementation; and user involvement. The plan is detailed to the task level in terms of necessary activities as the system is developed, refined, installed, and tested. These tasks are scheduled, on a preliminary basis, over a two-and-one-half-year time frame.

Verification System: First System-Wide Performance Test

NASA Astrophysics Data System (ADS)

Chernobay, I.; Zerbo, L.

2006-05-01

System-wide performance tests are essential for the development, testing and evaluation of individual components of the verification system. In addition to evaluating global readiness it helps establishing the practical and financial requirements for eventual operations. The first system-wide performance test (SPT1) was conducted in three phases: - A preparatory phase in May-June 2004 - A performance testing phase in April-June 2005 - An evaluation phase in the last half of 2005. The preparatory phase was developmental in nature. The main objectives for the performance testing phase included establishment of performance baseline under current provisional mode of operation (CTBT/PC- 19/1/Annex II, CTBT/WGB-21/1), examination of established requirements and procedures for operation and maintenance. To establish a system-wide performance baseline the system configuration was fixed for April-May 2005. The third month (June 2005) was used for implementation of 21 test case scenarios to examine either particular operational procedures or the response of the system components to the failures simulated under controlled conditions. A total of 163 stations and 5 certified radionuclide laboratories of International Monitoring System (IMS) participated in the performance testing phase - about 50% of the eventual IMS network. 156 IMS facilities and 40 National Data Centres (NDCs) were connected to the International Data Centre (IDC) via Global Communication Infrastructure (GCI) communication links. In addition, 12 legacy stations in the auxiliary seismic network sent data to the IDC over the Internet. During the performance testing phase, the IDC produced all required products, analysed more than 6100 seismic events and 1700 radionuclide spectra. Performance of all system elements was documented and analysed. IDC products were compared with results of data processing at the NDCs. On the basis of statistics and information collected during the SPT1 a system-wide performance baseline under current guidelines for provisional Operation and Maintenance was established. The test provided feedback for further development of the draft IMS and IDC Operational Manuals and identified priority areas for further system development.

Modeling pure culture heterotrophic production of polyhydroxybutyrate (PHB).

PubMed

Mozumder, Md Salatul Islam; Goormachtigh, Laurens; Garcia-Gonzalez, Linsey; De Wever, Heleen; Volcke, Eveline I P

2014-03-01

In this contribution a mechanistic model describing the production of polyhydroxybutyrate (PHB) through pure-culture fermentation was developed, calibrated and validated for two different substrates, namely glucose and waste glycerol. In both cases, non-growth-associated PHB production was triggered by applying nitrogen limitation. The occurrence of some growth-associated PHB production besides non-growth-associated PHB production was demonstrated, although it is inhibited in the presence of nitrogen. Other phenomena observed experimentally and described by the model included biomass growth on PHB and non-linear product inhibition of PHB production. The accumulated impurities from the waste substrate negatively affected the obtained maximum PHB content. Overall, the developed mathematical model provided an accurate prediction of the dynamic behavior of heterotrophic biomass growth and PHB production in a two-phase pure culture system. Copyright © 2013 Elsevier Ltd. All rights reserved.

Extending MODIS Cloud Top and Infrared Phase Climate Records with VIIRS and CrIS

NASA Astrophysics Data System (ADS)

Heidinger, A. K.; Platnick, S. E.; Ackerman, S. A.; Holz, R.; Meyer, K.; Frey, R.; Wind, G.; Li, Y.; Botambekov, D.

2015-12-01

The MODIS imagers on the NASA EOS Terra and Aqua satellites have generated accurate and well-used cloud climate data records for 15 years. Both missions are expected to continue until the end of this decade and perhaps beyond. The Visible and Infrared Imaging Radiometer Suite (VIIRS) imagers on the Suomi-NPP (SNPP) mission (launched in October 2011) and future NOAA Joint Polar Satellite System (JPSS) platforms are the successors for imager-based cloud climate records from polar orbiting satellites after MODIS. To ensure product continuity across a broad suite of EOS products, NASA has funded a SNPP science team to develop EOS-like algorithms that can be use with SNPP and JPSS observations, including two teams to work on cloud products. Cloud data record continuity between MODIS and VIIRS is particularly challenging due to the lack of VIIRS CO2-slicing channels, which reduces information content for cloud detection and cloud-top property products, as well as down-stream cloud optical products that rely on both. Here we report on our approach to providing continuity specifically for the MODIS/VIIRS cloud-top and infrared-derived thermodynamic phase products by combining elements of the NASA MODIS science team (MOD) and the NOAA Algorithm Working Group (AWG) algorithms. The combined approach is referred to as the MODAWG processing package. In collaboration with the NASA Atmospheric SIPS located at the University of Wisconsin Space Science and Engineering Center, the MODAWG code has been exercised on one year of SNPP VIIRS data. In addition to cloud-top and phase, MODAWG provides a full suite of cloud products that are physically consistent with MODIS and have a similar data format. Further, the SIPS has developed tools to allow use of Cross-track Infrared Sounder (CrIS) observations in the MODAWG processing that can ameliorate the loss of the CO2 absorption channels on VIIRS. Examples will be given that demonstrate the positive impact that the CrIS data can provide when combined with VIIRS for cloud height and IR-phase retrievals.

Determination of heavy polycyclic aromatic hydrocarbons by non-aqueous reversed phase liquid chromatography: Application and limitation in refining streams.

PubMed

Panda, Saroj K; Muller, Hendrik; Al-Qunaysi, Thunayyan A; Koseoglu, Omer R

2018-01-19

The heavy polycyclic aromatic hydrocarbons (HPAHs) cause detrimental effects to hydrocracker operations by deactivating the catalysts and depositing in the downstream of the reactor/ exchangers. Therefore, it is essential to continuously monitor the accumulation of HPAHs in a hydrocracker unit. To accurately measure the concentration of HPAHs, the development of a fast and reliable analytical method is inevitable. In this work, an analytical method based on non-aqueous reversed phase chromatography in combination with high resolution Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) was developed. As a first step, five different types of stationary phases were evaluated for the separation of HPAHs in non-aqueous mode and the best suited phase was further used for the fractionation of HPAHs in a fractionator bottom sample obtained from a refinery hydrocracker unit. The eight major fractions or peaks obtained from the separation were further characterized by UV spectroscopy and FT-ICR MS and the compounds in the fractions were tentatively confirmed as benzoperylene, coronene, methylcoronene, naphthenocoronene, benzocoronene, dibenzoperylene, naphthocoronene and ovalene. The developed liquid chromatography method can be easily adapted in a refinery laboratory for the quantitation of HPAHs in hydrocracking products. The method was further tested to check the interference of sulfur aromatics and/or large alkylated aromatic hydrocarbons on the determination of HPAHs in hydrocracking products. Copyright © 2017 Elsevier B.V. All rights reserved.

Column chromatography isolation of nicotine from tobacco leaf extract (Nicotiana tabaccum L.)

NASA Astrophysics Data System (ADS)

Fathi, Raden Muhammad; Fauzantoro, Ahmad; Rahman, Siti Fauziyah; Gozan, Misri

2018-02-01

Restrictions on the use of dried tobacco leaf for cigarette production must be accompanied by the development of non-cigarette alternative products that are made from tobacco leaves. One of the alternative that can be done is to use the nicotine compound in tobacco leaf extract as medical product, such as Parkinson's medication or to be used as active substance in biopesticide. Nicotine was isolated using column chromatography method with the variation of mobile phase mixture ratio (petroleum ether and ethanol), started from 8:2, 6:4, 4:6, 2:8, to 0:10. All of the chromatographic fraction from each mobile phase's ratio was then tested qualitatively using thin layer chromatography (TLC) and also quantitatively using HPLC instrument. The column chromatography process could isolate 4.006% of nicotine compound from 4.19% tobacco leaf extract's nicotine. It is also known that ethanol is a good solution to be used as chromatography's mobile phase for nicotine isolation from tobacco leaf extract.

Antibodies to watch in 2014: mid-year update.

PubMed

Reichert, Janice M

2014-01-01

The commercial pipeline of monoclonal antibodies is highly dynamic, with a multitude of transitions occurring during the year as product candidates advance through the clinical phases and onto the market. The data presented here add to that provided in the extensive "Antibodies to watch in 2014" report published in the January/February 2014 issue of mAbs. Recent phase transition data suggest that 2014 may be a banner year for first approvals of antibody therapeutics. As of May 2014, three products, ramucirumab (Cyramza®), siltuximab (Sylvant®) and vedolizumab (Entyvio™), had been granted first approvals in the United States, and four additional antibody therapeutics (secukinumab, dinutuximab, nivolumab, pembrolizumab) are undergoing regulatory review in either the US or the European Union. Other notable events include the start of first Phase 3 studies for seven antibody therapeutics (dupilumab, SA237, etrolizumab, MPDL3280A, bavituximab, clivatuzumab tetraxetan, blinatumomab). Relevant data for these product candidates are summarized, and metrics for antibody therapeutics development are discussed.

Statistical mechanics of complex economies

NASA Astrophysics Data System (ADS)

Bardoscia, Marco; Livan, Giacomo; Marsili, Matteo

2017-04-01

In the pursuit of ever increasing efficiency and growth, our economies have evolved to remarkable degrees of complexity, with nested production processes feeding each other in order to create products of greater sophistication from less sophisticated ones, down to raw materials. The engine of such an expansion have been competitive markets that, according to general equilibrium theory (GET), achieve efficient allocations under specific conditions. We study large random economies within the GET framework, as templates of complex economies, and we find that a non-trivial phase transition occurs: the economy freezes in a state where all production processes collapse when either the number of primary goods or the number of available technologies fall below a critical threshold. As in other examples of phase transitions in large random systems, this is an unintended consequence of the growth in complexity. Our findings suggest that the Industrial Revolution can be regarded as a sharp transition between different phases, but also imply that well developed economies can collapse if too many intermediate goods are introduced.

Development of a validated liquid chromatographic method for quantification of sorafenib tosylate in the presence of stress-induced degradation products and in biological matrix employing analytical quality by design approach.

PubMed

Sharma, Teenu; Khurana, Rajneet Kaur; Jain, Atul; Katare, O P; Singh, Bhupinder

2018-05-01

The current research work envisages an analytical quality by design-enabled development of a simple, rapid, sensitive, specific, robust and cost-effective stability-indicating reversed-phase high-performance liquid chromatographic method for determining stress-induced forced-degradation products of sorafenib tosylate (SFN). An Ishikawa fishbone diagram was constructed to embark upon analytical target profile and critical analytical attributes, i.e. peak area, theoretical plates, retention time and peak tailing. Factor screening using Taguchi orthogonal arrays and quality risk assessment studies carried out using failure mode effect analysis aided the selection of critical method parameters, i.e. mobile phase ratio and flow rate potentially affecting the chosen critical analytical attributes. Systematic optimization using response surface methodology of the chosen critical method parameters was carried out employing a two-factor-three-level-13-run, face-centered cubic design. A method operable design region was earmarked providing optimum method performance using numerical and graphical optimization. The optimum method employed a mobile phase composition consisting of acetonitrile and water (containing orthophosphoric acid, pH 4.1) at 65:35 v/v at a flow rate of 0.8 mL/min with UV detection at 265 nm using a C 18 column. Response surface methodology validation studies confirmed good efficiency and sensitivity of the developed method for analysis of SFN in mobile phase as well as in human plasma matrix. The forced degradation studies were conducted under different recommended stress conditions as per ICH Q1A (R2). Mass spectroscopy studies showed that SFN degrades in strongly acidic, alkaline and oxidative hydrolytic conditions at elevated temperature, while the drug was per se found to be photostable. Oxidative hydrolysis using 30% H 2 O 2 showed maximum degradation with products at retention times of 3.35, 3.65, 4.20 and 5.67 min. The absence of any significant change in the retention time of SFN and degradation products, formed under different stress conditions, ratified selectivity and specificity of the systematically developed method. Copyright © 2017 John Wiley & Sons, Ltd.

Effect of level of fiber of the rearing phase diets on egg production, digestive tract traits, and body measurements of brown egg-laying hens fed diets differing in energy concentration.

PubMed

Guzmán, P; Saldaña, B; Bouali, O; Cámara, L; Mateos, G G

2016-08-01

This research studied the effects of additional fiber in the rearing phase diets on egg production, gastrointestinal tract (GIT) traits, and body measurements of brown egg-laying hens fed diets varying in energy concentration from 17 to 46 wk of age. The experiment was completely randomized with 10 treatments arranged as a 5 × 2 factorial with 5 rearing phase diets and 2 laying phase diets. During the rearing phase, treatments consisted of a control diet based on cereals and soybean meal and 4 additional diets with a combination of 2 fiber sources (cereal straw and sugar beet pulp, SBP) at 2 levels (2 and 4%). During the laying phase, diets differed in energy content (2,650 vs. 2,750 kcal AMEn/kg) but had the same amino acid content per unit of energy. The rearing diet did not affect any production trait except egg production that was lower in birds fed SBP than in birds fed straw (91.6 and 94.1%, respectively; P < 0.05). Laying hens fed the high energy diet had lower feed intake (P < 0.001), better feed conversion (P < 0.01), and greater BW gain (P < 0.05) than hens fed the low energy diet but egg production and egg weight were not affected. At 46 wk of age, none of the GIT traits was affected by previous dietary treatment. At this age, hen BW was positively related with body length (r = 0.500; P < 0.01), tarsus length (r = 0.758; P < 0.001), and body mass index (r = 0.762; P < 0.001) but no effects of type of diet on these traits were detected. In summary, the inclusion of up to 4% of a fiber source in the rearing diets did not affect GIT development of the hens but SBP reduced egg production. An increase in the energy content of the laying phase diet reduced ADFI and improved feed efficiency but did not affect any of the other traits studied. © 2016 Poultry Science Association Inc.

Structural Evolution of Iron Antimonides from Amorphous Precursors to Crystalline Products Studied by Total Scattering Techniques.

PubMed

Bauers, Sage R; Wood, Suzannah R; Jensen, Kirsten M Ø; Blichfeld, Anders B; Iversen, Bo B; Billinge, Simon J L; Johnson, David C

2015-08-05

Homogeneous reaction precursors may be used to form several solid-state compounds inaccessible by traditional synthetic routes, but there has been little development of techniques that allow for a priori prediction of what may crystallize in a given material system. Here, the local structures of FeSbx designed precursors are determined and compared with the structural motifs of their crystalline products. X-ray total scattering and atomic pair distribution function (PDF) analysis are used to show that precursors that first nucleate a metastable FeSb3 compound share similar local structure to the product. Interestingly, precursors that directly crystallize to thermodynamically stable FeSb2 products also contain local structural motifs of the metastable phase, despite their compositional disagreement. While both crystalline phases consist of distorted FeSb6 octahedra with Sb shared between either two or three octahedra as required for stoichiometry, a corner-sharing arrangement indicative of AX3-type structures is the only motif apparent in the PDF of either precursor. Prior speculation was that local composition controlled which compounds nucleate from amorphous intermediates, with different compositions favoring different local arrangements and hence different products. This data suggests that local environments in these amorphous intermediates may not be very sensitive to overall composition. This can provide insight into potential metastable phases which may form in a material system, even with a precursor that does not crystallize to the kinetically stabilized product. Determination of local structure in homogeneous amorphous reaction intermediates from techniques such as PDF can be a valuable asset in the development of systematic methods to prepare targeted solid-state compounds from designed precursors.

Commercial-scale demonstration of the Liquid Phase Methanol (LPMEOH{sup trademark}) process. Third quarterly report, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The Liquid Phase Methanol (LPMEOH)(TM) demonstration project at King sport, Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L. P. (the Partnership). A demonstration unit producing 80,000 gallons per day (260 TPD) of methanol is being designed and constructed at a site located at the Eastman Chemical Company (Eastman) complex in Kingsport. The Partnership will own and operate the facility for the four year demonstration period. This project is sponsored under the DOE`s Clean Coal Technology Program, and its primary objective is to `demonstrate the production ofmore » methanol using the LPMEOH(TM) Process in conjunction with an integrated coal gasification facility.` The project will also demonstrate the suitability of the methanol produced for use as a chemical feedstock or as a low-sulfur dioxide, low-nitrogen oxides alternative fuel in stationary and transportation applications. The project may also demonstrate the production of dimethyl ether (DME) as a mixed coproduct with methanol, if laboratory- and pilot-scale research and market verification studies show promising results. If implemented, the DME would be produced during the last six months of the four year demonstration period. The LPMEOH(TM) process is the product of a cooperative development effort by Air Products and the DOE in a program that started in 1981. It was successfully piloted at a 10-TPD rate in the DOE-owned experimental unit at Air Products` LaPorte, Texas, site. This demonstration project is the culmination of that extensive cooperative development effort.« less

Stability-indicating UPLC method for determination of Valsartan and their degradation products in active pharmaceutical ingredient and pharmaceutical dosage forms.

PubMed

Krishnaiah, Ch; Reddy, A Raghupathi; Kumar, Ramesh; Mukkanti, K

2010-11-02

A simple, precise, accurate stability-indicating gradient reverse phase ultra-performance liquid chromatographic (RP-UPLC) method was developed for the quantitative determination of purity of Valsartan drug substance and drug products in bulk samples and pharmaceutical dosage forms in the presence of its impurities and degradation products. The method was developed using Waters Aquity BEH C18 (100 mm x 2.1 mm, 1.7 microm) column with mobile phase containing a gradient mixture of solvents A and B. The eluted compounds were monitored at 225 nm, the run time was within 9.5 min, which Valsartan and its seven impurities were well separated. Valsartan was subjected to the stress conditions of oxidative, acid, base, hydrolytic, thermal and photolytic degradation. Valsartan was found to degrade significantly in acid and oxidative stress conditions and stable in base, hydrolytic and photolytic degradation conditions. The degradation products were well resolved from main peak and its impurities, proving the stability-indicating power of the method. The developed method was validated as per international conference on harmonization (ICH) guidelines with respect to specificity, linearity, limit of detection, limit of quantification, accuracy, precision and robustness. This method was also suitable for the assay determination of Valsartan in pharmaceutical dosage forms.

Thermal Clothing

NASA Technical Reports Server (NTRS)

1997-01-01

Gateway Technologies, Inc. is marketing and developing textile insulation technology originally developed by Triangle Research and Development Corporation. The enhanced thermal insulation stems from Small Business Innovation Research contracts from NASA's Johnson Space Center and the U.S. Air Force. The effectiveness of the insulation comes from the microencapsulated phase-change materials originally made to keep astronauts gloved hands warm. The applications for the product range from outer wear, housing insulation, and blankets to protective firefighting gear and scuba diving suits. Gateway has developed and begun marketing thermal regulating products under the trademark, OUTLAST. Products made from OUTLAST are already on the market, including boot and shoe liners, winter headgear, hats and caps for hunting and other outdoor sports, and a variety of men's and women's ski gloves.

Process development for automated solar cell and module production. Task 4: Automated array assembly

NASA Technical Reports Server (NTRS)

Hagerty, J. J.

1981-01-01

Progress in the development of automated solar cell and module production is reported. The unimate robot is programmed for the final 35 cell pattern to be used in the fabrication of the deliverable modules. The mechanical construction of the automated lamination station and final assembly station phases are completed and the first operational testing is underway. The final controlling program is written and optimized. The glass reinforced concrete (GRC) panels to be used for testing and deliverables are in production. Test routines are grouped together and defined to produce the final control program.

Surface mining

Treesearch

Robert Leopold; Bruce Rowland; Reed Stalder

1979-01-01

The surface mining process consists of four phases: (1) exploration; (2) development; (3) production; and (4) reclamation. A variety of surface mining methods has been developed, including strip mining, auger, area strip, open pit, dredging, and hydraulic. Sound planning and design techniques are essential to implement alternatives to meet the myriad of laws,...

High Technology Product Training for Sales Representatives of Spectrum Healthcare Solutions and International Business Machines Corporation.

ERIC Educational Resources Information Center

Crystal, Enid

This report describes an application of the Instructional Systems Design (ISD) process to a product knowledge training project for Spectrum Healthcare Solutions, Inc., including the steps and substeps in the phases of analysis, design, development, implementation, and evaluation. The training project was designed to address the need for increased…

Development of textile-based high-tech products: the new challenge.

PubMed

da Rocha, Ana Maria M F

2004-01-01

The new generation of smart textiles is represented by fibers, yarns, fabrics and other resulting products that have special properties, regarding mechanical, chemical, electrical and thermal performances. These high-tech products, being able to respond to external stimuli through the integration of electronic components, phase change materials, shape memory materials or nano materials, enabled the development of different active and functional products. These products when combining the functions of medium, carrier and interface for micro-systems applications represent the ideal connecting channel between humans and the environment. This is a field of innovation that broadened the scope of the traditional textile and apparel products to high-tech textiles, designed to meet specific needs, involving different technologies and produced according to required properties, like personal protection, safety, leisure or health wear. The development of smart wear is a new challenge for the textile and clothing industry: it has to develop products based not only on design, fashion and comfort concepts but also in terms of functions. Moreover these products must be easy to care and durable.

Methods Used to Support a Life Cycle of Complex Engineering Products

NASA Astrophysics Data System (ADS)

Zakharova, Alexandra A.; Kolegova, Olga A.; Nekrasova, Maria E.; Eremenko, Andrey O.

2016-08-01

Management of companies involved in the design, development and operation of complex engineering products recognize the relevance of creating systems for product lifecycle management. A system of methods is proposed to support life cycles of complex engineering products, based on fuzzy set theory and hierarchical analysis. The system of methods serves to demonstrate the grounds for making strategic decisions in an environment of uncertainty, allows the use of expert knowledge, and provides interconnection of decisions at all phases of strategic management and all stages of a complex engineering product lifecycle.

Production Time Loss Reduction in Sauce Production Line by Lean Six Sigma Approach

NASA Astrophysics Data System (ADS)

Ritprasertsri, Thitima; Chutima, Parames

2017-06-01

In all industries, time losses, which are incurred in processing are very important. As a result, losses are incurred in productivity and cost. This research aimed to reduce lost time that occurs in sauce production line by using the lean six sigma approach. The main objective was to reduce the time for heating sauce which causes a lot of time lost in the production line which affects productivity. The methodology was comprised of the five-phase improvement model of Six Sigma. This approach begins with defining phase, measuring phase, analysing phase, improving phase and controlling phase. Cause-and-effect matrix and failure mode and effect analysis (FMEA) were adopted to screen the factors which affect production time loss. The results showed that the percentage of lost time from heating sauce reduced by 47.76%. This increased productivity to meet the plan.

Biomass power for rural development. Technical progress report, May 1, 1996--December 31, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neuhauser, E.

Developing commercial energy crops for power generation by the year 2000 is the focus of the DOE/USDA sponsored Biomass Power for Rural Development project. The New York based Salix Consortium project is a multi-partner endeavor, implemented in three stages. Phase-I, Final Design and Project Development, will conclude with the preparation of construction and/or operating permits, feedstock production plans, and contracts ready for signature. Field trials of willow (Salix) have been initiated at several locations in New York (Tully, Lockport, King Ferry, La Facette, Massena, and Himrod) and co-firing tests are underway at Greenidge Station (NYSEG). Phase-II of the project willmore » focus on scale-up of willow crop acreage, construction of co-firing facilities at Dunkirk Station (NMPC), and final modifications for Greenidge Station. There will be testing of the energy crop as part of the gasification trials expected to occur at BED`s McNeill power station and potentially at one of GPU`s facilities. Phase-III will represent full-scale commercialization of the energy crop and power generation on a sustainable basis. Willow has been selected as the energy crop of choice for many reasons. Willow is well suited to the climate of the Northeastern United States, and initial field trials have demonstrated that the yields required for the success of the project are obtainable. Like other energy crops, willow has rural development benefits and could serve to diversify local crop production, provide new sources of income for participating growers, and create new jobs. Willow could be used to put a large base of idle acreage back into crop production. Additionally, the willow coppicing system integrates well with current farm operations and utilizes agricultural practices that are already familiar to farmers.« less

Investigating the Use of Interactive Whiteboards during the Pre-Task Phase of Speaking Tasks in the Secondary English Classroom

ERIC Educational Resources Information Center

Handley, Zoe

2012-01-01

Working within a task-based approach to the teaching of speaking, two interactive whiteboard-based pre-task activities focusing on different phases of the speech production process (Levelt, 1989) were developed and compared with an activity based on the speaking activities currently offered in English as a foreign language course books. The first…

Multidisciplinary approach to successful implementation of production information system (PRISM)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shariff, M.R.; Gopalakrishnan, S.G.; Francis, N.

1995-12-31

A company wide corporate and regional production database supporting all production areas was envisaged critical to the current expansion within Petronas Carigali Sdn Bhd (PCSB). A multi disciplinary project team was thus formed to analyze the requirements prior to developing, testing, implementing and training users. PCSB has currently evolved into a mature E & P company on par with other E & P companies within the region. This expansion necessitates a common Production Information System for the efficient dissemination of vital Production Information for Production Surveillance, Reservoir Management, Reserve Assessment, Special Studies and Standardized Group-wide Reporting. This paper will discussmore » all the phases involved in the project which includes Systems Requirement Study, Data Migration, System Development, System Implementation and Post-Implementation Plan.« less

The Outer Planetary Mission Design Project

NASA Astrophysics Data System (ADS)

Benfield, Michael; Turner, M. W.

2010-10-01

With the recent focus from the planetary science community on the outer planets of the solar system, The University of Alabama in Huntsville Integrated Product Team program is embarking on a new challenge to develop an outer planetary mission for the academic year 2010-2011. Currently four bodies are of interest for this mission: Titan, Europa, Triton, and Enceledus, with one body being chosen by the instructors by the beginning of the fall semester. This project will use the 2010 Discovery Announcement of Opportunity as its Request for Proposal (RFP). All of the teams competing in this project will use the AO to respond with a proposal to the instructors for their proposed mission and spacecraft concept. The project employs the two-semester design sequence of the IPT program to provide a framework for the development of this mission. This sequence is divided into four phases. Phase 1 - Requirements Development - focuses on the development of both the scientific and engineering requirements of the mission. During this phase the teams work very closely with the PI organization, represented by the College of Charleston. Phase 2 - Team Formation and Architecture Development - concentrates on the assessment of the overall mission architecture from the launch vehicle to the ground operations of the proposed spacecraft. Phase 3 - System Definition - provides for spacecraft subsystem trade studies and further refinement of the specific spacecraft to meet the scientific requirements and objectives developed in Phase 1. Phase 4 - Design - is the phase where the engineers provide the spacecraft design that is required for the mission of interest. At the conclusion of Phases 2 and 4, an external review board evaluates the proposed designs and chooses one winner of the competition.

Thermodynamic Description of the Quaternary Ag-Bi-Cu-Sn System

NASA Astrophysics Data System (ADS)

Gierlotka, Wojciech

2018-01-01

Lead-free soldering is an important part of electronic devices production. New lead-free solders that replace classical Sn-37Pb solder are still under development. Thermodynamic modeling makes the development process faster, cheaper and more environmentally friendly due to predictions of phases stabilities and phases transformations. In this work, the thermodynamic description of quaternary Ag-Bi-Cu-Sn system is presented. The thermodynamic assessment of promising lead-free quaternary solder was prepared using the Calphad approach. A good agreement between available experimental data and calculation was found.

Mechanism and microstructures in Ga2O3 pseudomartensitic solid phase transition.

PubMed

Zhu, Sheng-Cai; Guan, Shu-Hui; Liu, Zhi-Pan

2016-07-21

Solid-to-solid phase transition, although widely exploited in making new materials, challenges persistently our current theory for predicting its complex kinetics and rich microstructures in transition. The Ga2O3α-β phase transformation represents such a common but complex reaction with marked change in cation coordination and crystal density, which was known to yield either amorphous or crystalline products under different synthetic conditions. Here we, via recently developed stochastic surface walking (SSW) method, resolve for the first time the atomistic mechanism of Ga2O3α-β phase transformation, the pathway of which turns out to be the first reaction pathway ever determined for a new type of diffusionless solid phase transition, namely, pseudomartensitic phase transition. We demonstrate that the sensitivity of product crystallinity is caused by its multi-step, multi-type reaction pathway, which bypasses seven intermediate phases and involves all types of elementary solid phase transition steps, i.e. the shearing of O layers (martensitic type), the local diffusion of Ga atoms (reconstructive type) and the significant lattice dilation (dilation type). While the migration of Ga atoms across the close-packed O layers is the rate-determining step and yields "amorphous-like" high energy intermediates, the shearing of O layers contributes to the formation of coherent biphase junctions and the presence of a crystallographic orientation relation, (001)α//(201[combining macron])β + [120]α//[13[combining macron]2]β. Our experiment using high-resolution transmission electron microscopy further confirms the theoretical predictions on the atomic structure of biphase junction and the formation of (201[combining macron])β twin, and also discovers the late occurrence of lattice expansion in the nascent β phase that grows out from the parent α phase. By distinguishing pseudomartensitic transition from other types of mechanisms, we propose general rules to predict the product crystallinity of solid phase transition. The new knowledge on the kinetics of pseudomartensitic transition complements the theory of diffusionless solid phase transition.

Microstructure studies of interdiffusion behavior of U 3Si 2/Zircaloy-4 at 800 and 1000 °C

DOE PAGES

He, Lingfeng; Harp, Jason M.; Hoggan, Rita E.; ...

2017-01-22

Fuel swelling during normal reactor operations could lead to unfavorable chemical interactions when in contact with its cladding. As new fuel types are developed, it is crucial to understand the interaction behavior between fuel and its cladding. Diffusion experiments between U 3Si 2 and Zricaloy-4 (Zry-4) were conducted at 800 and 1000°C up to 100 hours. The microstructure of pristine U 3Si 2 and U 3Si 2/Zry-4 interdiffusion products were examined using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) equipped with an energy dispersive X-ray spectroscopy (EDS) system. The primary interdiffusion product observed at 800°C is ZrSi 2,more » with secondary phases of U-Zr in the Zry-4, and Fe-Cr-W-Zr-Si phases at Zry-4/ZrSi 2 interface and Fe-Cr-U-Si phases at ZrSi 2/U-Si interface. As a result, the primary interdiffusion products at 1000°C were Zr 2Si, U-Zr-Fe-Ni, U, U-Zr, and a low melting point phase U 6Fe.« less

In situ production of titanium dioxide nanoparticles in molten salt phase for thermal energy storage and heat-transfer fluid applications

NASA Astrophysics Data System (ADS)

Lasfargues, Mathieu; Bell, Andrew; Ding, Yulong

2016-06-01

In this study, TiO2 nanoparticles (average particle size 16 nm) were successfully produced in molten salt phase and were showed to significantly enhance the specific heat capacity of a binary eutectic mixture of sodium and potassium nitrate (60/40) by 5.4 % at 390 °C and 7.5 % at 445 °C for 3.0 wt% of precursors used. The objective of this research was to develop a cost-effective alternate method of production which is potentially scalable, as current techniques utilized are not economically viable for large quantities. Enhancing the specific heat capacity of molten salt would promote more competitive pricing for electricity production by concentrating solar power plant. Here, a simple precursor (TiOSO4) was added to a binary eutectic mixture of potassium and sodium nitrate, heated to 450 °C, and cooled to witness the production of nanoparticles.

Wet catalyst-support films for production of vertically aligned carbon nanotubes.

PubMed

Alvarez, Noe T; Hamilton, Christopher E; Pint, Cary L; Orbaek, Alvin; Yao, Jun; Frosinini, Aldo L; Barron, Andrew R; Tour, James M; Hauge, Robert H

2010-07-01

A procedure for vertically aligned carbon nanotube (VA-CNT) production has been developed through liquid-phase deposition of alumoxanes (aluminum oxide hydroxides, boehmite) as a catalyst support. Through a simple spin-coating of alumoxane nanoparticles, uniform centimer-square thin film surfaces were coated and used as supports for subsequent deposition of metal catalyst. Uniform VA-CNTs are observed to grow from this film following deposition of both conventional evaporated Fe catalyst, as well as premade Fe nanoparticles drop-dried from the liquid phase. The quality and uniformity of the VA-CNTs are comparable to growth from conventional evaporated layers of Al(2)O(3). The combined use of alumoxane and Fe nanoparticles to coat surfaces represents an inexpensive and scalable approach to large-scale VA-CNT production that makes chemical vapor deposition significantly more competitive when compared to other CNT production techniques.

Methyl chloride via oxyhydrochlorination of methane: A building block for chemicals and fuels from natural gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benson, R.L.; Brown, S.S.D.; Ferguson, S.P.

1995-12-31

The objectives of this program are to (a) develop a process for converting natural gas to methyl chloride via an oxyhydrochlorination route using highly selective, stable catalysts in a fixed-bed, (b) design a reactor capable of removing the large amount of heat generated in the process so as to control the reaction, (c) develop a recovery system capable of removing the methyl chloride from the product stream and (d) determine the economics and commercial viability of the process. The general approach has been as follows: (a) design and build a laboratory scale reactor, (b) define and synthesize suitable OHC catalystsmore » for evaluation, (c) select first generation OHC catalyst for Process Development Unit (PDU) trials, (d) design, construct and startup PDU, (e) evaluate packed bed reactor design, (f) optimize process, in particular, product recovery operations, (g) determine economics of process, (h) complete preliminary engineering design for Phase II and (i) make scale-up decision and formulate business plan for Phase II. Conclusions regarding process development and catalyst development are presented.« less

A combination strategy for extraction and isolation of multi-component natural products by systematic two-phase solvent extraction-(13)C nuclear magnetic resonance pattern recognition and following conical counter-current chromatography separation: Podophyllotoxins and flavonoids from Dysosma versipellis (Hance) as examples.

PubMed

Yang, Zhi; Wu, Youqian; Wu, Shihua

2016-01-29

Despite of substantial developments of extraction and separation techniques, isolation of natural products from natural resources is still a challenging task. In this work, an efficient strategy for extraction and isolation of multi-component natural products has been successfully developed by combination of systematic two-phase liquid-liquid extraction-(13)C NMR pattern recognition and following conical counter-current chromatography separation. A small-scale crude sample was first distributed into 9 systematic hexane-ethyl acetate-methanol-water (HEMWat) two-phase solvent systems for determination of the optimum extraction solvents and partition coefficients of the prominent components. Then, the optimized solvent systems were used in succession to enrich the hydrophilic and lipophilic components from the large-scale crude sample. At last, the enriched components samples were further purified by a new conical counter-current chromatography (CCC). Due to the use of (13)C NMR pattern recognition, the kinds and structures of major components in the solvent extracts could be predicted. Therefore, the method could collect simultaneously the partition coefficients and the structural information of components in the selected two-phase solvents. As an example, a cytotoxic extract of podophyllotoxins and flavonoids from Dysosma versipellis (Hance) was selected. After the systematic HEMWat system solvent extraction and (13)C NMR pattern recognition analyses, the crude extract of D. versipellis was first degreased by the upper phase of HEMWat system (9:1:9:1, v/v), and then distributed in the two phases of the system of HEMWat (2:8:2:8, v/v) to obtain the hydrophilic lower phase extract and lipophilic upper phase extract, respectively. These extracts were further separated by conical CCC with the HEMWat systems (1:9:1:9 and 4:6:4:6, v/v). As results, total 17 cytotoxic compounds were isolated and identified. In general, whole results suggested that the strategy was very efficient for the systematic extraction and isolation of biological active components from the complex biomaterials. Copyright © 2016 Elsevier B.V. All rights reserved.

Novel licensure pathways for expeditious introduction of new tuberculosis vaccines: a discussion of the adaptive licensure concept.

PubMed

Rustomjee, Roxana; Lockhart, Stephen; Shea, Jacqueline; Fourie, P Bernard; Hindle, Zoë; Steel, Gavin; Hussey, Gregory; Ginsberg, Ann; Brennan, Michael J

2014-03-01

The ultimate goal of vaccine development is licensure of a safe and efficacious product that has a well-defined manufacturing process resulting in a high quality product. In general, clinical development and regulatory approval occurs in a linear, sequential manner: Phase 1 - safety, immunogenicity; Phase 2 - immunogenicity, safety, dose ranging and preliminary efficacy; Phase 3 - definitive efficacy, safety, lot consistency; and, following regulatory approval, Phase 4 - post-marketing safety and effectiveness. For candidate TB vaccines, where correlates of protection are not yet identified, phase 2 and 3 efficacy of disease prevention trials are, by necessity, very large. Each trial would span 2-5 years, with full licensure expected only after 1 or even 2 decades of development. Given the urgent unmet need for a new TB vaccine, a satellite discussion was held at the International African Vaccinology Conference in Cape Town, South Africa in November 2012, to explore the possibility of expediting licensure by use of an "adaptive licensure" process, based on a risk/benefit assessment that is specific to regional needs informed by epidemiology. This may be appropriate for diseases such as TB, where high rates of morbidity, mortality, particularly in high disease burden countries, impose an urgent need for disease prevention. The discussion focused on two contexts: licensure within the South African regulatory environment - a high burden country where TB vaccine efficacy trials are on-going, and licensure by the United States FDA --a well-resourced regulatory agency where approval could facilitate global licensure of a novel TB vaccine. Copyright © 2013. Published by Elsevier Ltd.

Silicon material task - Low cost solar array project /JPL/DOE/

NASA Technical Reports Server (NTRS)

Lutwack, R.

1979-01-01

The paper describes the silicon material task of the low-cost solar array project, which has the objective of establishing a silicon production capability equivalent to 500 mW per year at a price less than 10 dollars/kg (1975 dollars) in 1986. The task program is divided into four phases: technical feasibility, scale-up studies (the present phase), experimental process system development units, and implementation of large-scale production plants, and it involves the development of processes for two groups of materials, that is, semiconductor grade and solar cell grade. In addition, the effects of impurities on solar cell performance are being investigated. Attention is given to problem areas of the task program, such as environmental protection, material compatibility between the reacting chemicals and materials of construction of the equipment, and waste disposal.

A genetic switch controls the production of flagella and toxins in Clostridium difficile

PubMed Central

2017-01-01

In the human intestinal pathogen Clostridium difficile, flagella promote adherence to intestinal epithelial cells. Flagellar gene expression also indirectly impacts production of the glucosylating toxins, which are essential to diarrheal disease development. Thus, factors that regulate the expression of the flgB operon will likely impact toxin production in addition to flagellar motility. Here, we report the identification a “flagellar switch” that controls the phase variable production of flagella and glucosylating toxins. The flagellar switch, located upstream of the flgB operon containing the early stage flagellar genes, is a 154 bp invertible sequence flanked by 21 bp inverted repeats. Bacteria with the sequence in one orientation expressed flagellum and toxin genes, produced flagella, and secreted the toxins (“flg phase ON”). Bacteria with the sequence in the inverse orientation were attenuated for flagellar and toxin gene expression, were aflagellate, and showed decreased toxin secretion (“flg phase OFF”). The orientation of the flagellar switch is reversible during growth in vitro. We provide evidence that gene regulation via the flagellar switch occurs post-transcription initiation and requires a C. difficile-specific regulatory factor to destabilize or degrade the early flagellar gene mRNA when the flagellar switch is in the OFF orientation. Lastly, through mutagenesis and characterization of flagellar phase locked isolates, we determined that the tyrosine recombinase RecV, which catalyzes inversion at the cwpV switch, is also responsible for inversion at the flagellar switch in both directions. Phase variable flagellar motility and toxin production suggests that these important virulence factors have both advantageous and detrimental effects during the course of infection. PMID:28346491

Automatic Command Sequence Generation

NASA Technical Reports Server (NTRS)

Fisher, Forest; Gladded, Roy; Khanampompan, Teerapat

2007-01-01

Automatic Sequence Generator (Autogen) Version 3.0 software automatically generates command sequences for the Mars Reconnaissance Orbiter (MRO) and several other JPL spacecraft operated by the multi-mission support team. Autogen uses standard JPL sequencing tools like APGEN, ASP, SEQGEN, and the DOM database to automate the generation of uplink command products, Spacecraft Command Message Format (SCMF) files, and the corresponding ground command products, DSN Keywords Files (DKF). Autogen supports all the major multi-mission mission phases including the cruise, aerobraking, mapping/science, and relay mission phases. Autogen is a Perl script, which functions within the mission operations UNIX environment. It consists of two parts: a set of model files and the autogen Perl script. Autogen encodes the behaviors of the system into a model and encodes algorithms for context sensitive customizations of the modeled behaviors. The model includes knowledge of different mission phases and how the resultant command products must differ for these phases. The executable software portion of Autogen, automates the setup and use of APGEN for constructing a spacecraft activity sequence file (SASF). The setup includes file retrieval through the DOM (Distributed Object Manager), an object database used to store project files. This step retrieves all the needed input files for generating the command products. Depending on the mission phase, Autogen also uses the ASP (Automated Sequence Processor) and SEQGEN to generate the command product sent to the spacecraft. Autogen also provides the means for customizing sequences through the use of configuration files. By automating the majority of the sequencing generation process, Autogen eliminates many sequence generation errors commonly introduced by manually constructing spacecraft command sequences. Through the layering of commands into the sequence by a series of scheduling algorithms, users are able to rapidly and reliably construct the desired uplink command products. With the aid of Autogen, sequences may be produced in a matter of hours instead of weeks, with a significant reduction in the number of people on the sequence team. As a result, the uplink product generation process is significantly streamlined and mission risk is significantly reduced. Autogen is used for operations of MRO, Mars Global Surveyor (MGS), Mars Exploration Rover (MER), Mars Odyssey, and will be used for operations of Phoenix. Autogen Version 3.0 is the operational version of Autogen including the MRO adaptation for the cruise mission phase, and was also used for development of the aerobraking and mapping mission phases for MRO.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pallesen, T.R.; Braestrup, M.W.; Jorgensen, O.

Development of Danish North Sea hydrocarbon resources includes the 17-km Rolf pipeline installed in 1985. This one consists of an insulated 8-in. two-phase flow product line with a 3-in. piggyback gas lift line. A practical solution to design of this insulated pipeline, including the small diameter, piggyback injection line was corrosion coating of fusion bonded epoxy (FBE) and polyethylene (PE) sleeve pipe. The insulation design prevents hydrate formation under the most conservative flow regime during gas lift production. Also, the required minimum flow rate during the initial natural lift period is well below the value anticipiated at the initiation ofmore » gas lift. The weight coating design ensures stability on the seabed during the summer months only; thus trenching was required during the same installation season. Installation of insulated flowlines serving marginal fields is a significant feature of North Sea hydrocarbon development projects. The Skjold field is connected to Gorm by a 6-in., two-phase-flow line. The 11-km line was installed in 1982 as the first insulated pipeline in the North Sea. The Rolf field, located 17 km west of Gorm, went on stream Jan. 2. The development includes an unmanned wellhead platform and an insulated, two-phase-flow pipeline to the Gorm E riser platform. After separation on the Gorm C process platform, the oil and condensate are transported to shore through the 20-in. oil pipeline, and the natural gas is piped to Tyra for transmission through the 30-in. gas pipeline. Oil production at Rolf is assisted by the injection of lift gas, transported from Gorm through a 3-in. pipeline, installed piggyback on the insulated 8-in. product line. The seabed is smooth and sandy, the water depth varying between 33.7 m (110.5 ft) at Rolf and 39.1 m (128 ft) at Gorm.« less

CORE-BASED INTEGRATED SEDIMENTOLOGIC, STRATIGRAPHIC, AND GEOCHEMICAL ANALYSIS OF THE OIL SHALE BEARING GREEN RIVER FORMATION, UINTA BASIN, UTAH

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lauren P. Birgenheier; Michael D. Vanden Berg,

An integrated detailed sedimentologic, stratigraphic, and geochemical study of Utah's Green River Formation has found that Lake Uinta evolved in three phases (1) a freshwater rising lake phase below the Mahogany zone, (2) an anoxic deep lake phase above the base of the Mahogany zone and (3) a hypersaline lake phase within the middle and upper R-8. This long term lake evolution was driven by tectonic basin development and the balance of sediment and water fill with the neighboring basins, as postulated by models developed from the Greater Green River Basin by Carroll and Bohacs (1999). Early Eocene abrupt global-warmingmore » events may have had significant control on deposition through the amount of sediment production and deposition rates, such that lean zones below the Mahogany zone record hyperthermal events and rich zones record periods between hyperthermals. This type of climatic control on short-term and long-term lake evolution and deposition has been previously overlooked. This geologic history contains key points relevant to oil shale development and engineering design including: (1) Stratigraphic changes in oil shale quality and composition are systematic and can be related to spatial and temporal changes in the depositional environment and basin dynamics. (2) The inorganic mineral matrix of oil shale units changes significantly from clay mineral/dolomite dominated to calcite above the base of the Mahogany zone. This variation may result in significant differences in pyrolysis products and geomechanical properties relevant to development and should be incorporated into engineering experiments. (3) This study includes a region in the Uinta Basin that would be highly prospective for application of in-situ production techniques. Stratigraphic targets for in-situ recovery techniques should extend above and below the Mahogany zone and include the upper R-6 and lower R-8.« less

Phase change water processing for Space Station

NASA Technical Reports Server (NTRS)

Zdankiewicz, E. M.; Price, D. F.

1985-01-01

The use of a vapor compression distillation subsystem (VCDS) for water recovery on the Space Station is analyzed. The self-contained automated system can process waste water at a rate of 32.6 kg/day and requires only 115 W of electric power. The improvements in the mechanical components of VCDS are studied. The operation of VCDS in the normal mode is examined. The VCDS preprototype is evaluated based on water quality, water production rate, and specific energy. The relation between water production rate and fluids pump speed is investigated; it is concluded that a variable speed fluids pump will optimize water production. Components development and testing currently being conducted are described. The properties and operation of the proposed phase change water processing system for the Space Station, based on vapor compression distillation, are examined.

Study of solid rocket motors for a space shuttle booster. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1972-01-01

An analysis of the solid propellant rocket engines for use with the space shuttle booster was conducted. A definition of the specific solid propellant rocket engine stage designs, development program requirements, production requirements, launch requirements, and cost data for each program phase were developed.

A model of the pre-Sedov expansion phase of supernova remnant-ambient plasma coupling and X-ray emission from SN 1987A

NASA Technical Reports Server (NTRS)

Spicer, D. S.; Maran, S. P.; Clark, R. W.

1990-01-01

This paper examines the mechanism responsible for coupling supernova (SN) remnant to the ambient medium during the pre-Sedov or the so-called free expansion phase, immediately following the progenitor explosion. A theory is developed for the interaction of an SN piston with the ambient medium during the pre-Sedov phase. The possibility of X-ray production by the high-speed portion of the piston during this phase is investigated. The relevant observations of high-energy emissions from the SN 1987A, including the X-ray spectrum, luminosity, and temporal development, are considered. It is shown that the commonly assumed snowplow model for SNR evolution is valid, because of the action of a variety of collisionless two-stream instabilities that permit the coupling of the ambient plasma with SNR.

Diffusion-based process for carbon dioxide uptake and isoprene emission in gaseous/aqueous two-phase photobioreactors by photosynthetic microorganisms.

PubMed

Bentley, Fiona K; Melis, Anastasios

2012-01-01

Photosynthesis for the generation of fuels and chemicals from cyanobacteria and microalgae offers the promise of a single host organism acting both as photocatalyst and processor, performing sunlight absorption and utilization, as well as CO(2) assimilation and conversion into product. However, there is a need to develop methods for generating, sequestering, and trapping such bio-products in an efficient and cost-effective manner that is suitable for industrial scale-up and exploitation. A sealed gaseous/aqueous two-phase photobioreactor was designed and applied for the photosynthetic generation of volatile isoprene (C(5)H(8)) hydrocarbons, which operates on the principle of spontaneous diffusion of CO(2) from the gaseous headspace into the microalgal or cyanobacterial-containing aqueous phase, followed by photosynthetic CO(2) assimilation and isoprene production by the transgenic microorganisms. Volatile isoprene hydrocarbons were emitted from the aqueous phase and were sequestered into the gaseous headspace. Periodic replacement (flushing) of the isoprene (C(5)H(8)) and oxygen (O(2)) content of the gaseous headspace with CO(2) allowed for the simultaneous harvesting of the photoproducts and replenishment of the CO(2) supply in the gaseous headspace. Reduction in practice of the gaseous/aqueous two-phase photobioreactor is offered in this work with a fed-batch and a semi-continuous culturing system using Synechocystis sp. PCC 6803 heterologously expressing the Pueraria montana (kudzu) isoprene synthase (IspS) gene. Constitutive isoprene production was observed over 192 h of experimentation, coupled with cyanobacterial biomass accumulation. The diffusion-based process in gaseous/aqueous two-phase photobioreactors has the potential to be applied to other high-value photosynthetically derived volatile molecules, emanating from a variety of photosynthetic microorganisms. Copyright © 2011 Wiley Periodicals, Inc.

Examining the roles that changing harvested areas, closing yield-gaps, and increasing yield ceilings have had on crop production

NASA Astrophysics Data System (ADS)

Johnston, M.; Ray, D. K.; Mueller, N. D.; Foley, J. A.

2011-12-01

With an increasing and increasingly affluent population, there has been tremendous effort to examine strategies for sustainably increasing agricultural production to meet this surging global demand. Before developing new solutions from scratch, though, we believe it is important to consult our recent agricultural history to see where and how agricultural production changes have already taken place. By utilizing the newly created temporal M3 cropland datasets, we can for the first time examine gridded agricultural yields and area, both spatially and temporally. This research explores the historical drivers of agricultural production changes, from 1965-2005. The results will be presented spatially at the global-level (5-min resolution), as well as at the individual country-level. The primary research components of this study are presented below, including the general methodology utilized in each phase and preliminary results for soybean where available. The complete assessment will cover maize, wheat, rice, soybean, and sugarcane, and will include country-specific analysis for over 200 countries, states, territories and protectorates. Phase 1: The first component of our research isolates changes in agricultural production due to variation in planting decisions (harvested area) from changes in production due to intensification efforts (yield). We examine area/yield changes at the pixel-level over 5-year time-steps to determine how much each component has contributed to overall changes in production. Our results include both spatial patterns of changes in production, as well as spatial maps illustrating to what degree the production change is attributed to area and/or yield. Together, these maps illustrate where, why, and by how much agricultural production has changed over time. Phase 2: In the second phase of our research we attempt to determine the impact that area and yield changes have had on agricultural production at the country-level. We calculate a production-weighted result of area and yield contributions for each country, at each time-step. As part of our research we will generate historic figures and tabular data for every country-crop combination. Phase 3: In the final phase of our research, we attempt to demonstrate how different yield performers (for example, those growing crops at the yield floor vs. the yield ceiling) have utilized different area/yield strategies to increase agricultural production. To group individual pixels into performance quintiles, we utilize binning strategies from previous spatial yield-gap assessments. The results from this step will illustrate how the yield ceiling has improved over time vis-à-vis improvements in the yield floor. As we look forward to a more sustainable and productive agricultural future, we hope the results of this global analysis of our agricultural past can be utilized to identify both optimal and adverse strategies for agricultural growth.

An investigation of low ergonomics risk awareness, among staffs at early product development phase in Malaysia automotive industries

NASA Astrophysics Data System (ADS)

Aziz, Fazilah Abdul; Razali, Noraini; Najmiyah Jaafar, Nur

2016-02-01

Currently there are many automotive companies still unable to effectively prevent consequences of poor ergonomics in their manufacturing processes. This study purpose is to determine the surrounding factors that influence low ergonomics risk awareness among staffs at early product development phase in Malaysia automotive industry. In this study there are four variables, low ergonomic risk awareness, inappropriate method and tools, tight development schedule and lack of management support. The survey data were gathered from 245 respondents of local automotive companies in Malaysia. The data was analysed through multiple regression and moderated regression using the IBM SPSS software. Study results revealed that low ergonomic risk awareness has influenced by inappropriate method and tool, and tight development schedule. There were positive linear relationships between low ergonomic risk awareness and inappropriate method and tools, and tight development schedule. The more inappropriate method and tools applied; the lower their ergonomic risk awareness. The more tight development schedule is the lower ergonomic risk awareness. The relationship between low ergonomic risk awareness and inappropriate method and tools depends on staff's age, and education level. Furthermore the relationship between low ergonomic risk awareness and tight development schedule depends on staff's working experience and number of project involvement. The main contribution of this paper was identified the number of factors of low ergonomics risk awareness and offers better understanding on ergonomics among researchers and automotive manufacturer's employees during product development process.

Crew interface specifications preparation for in-flight maintenance and stowage functions

NASA Technical Reports Server (NTRS)

Parker, F. W.; Carlton, B. E.

1972-01-01

The findings and data products developed during the Phase 2 crew interface specification study are presented. Five new NASA general specifications were prepared: operations location coding system for crew interfaces; loose equipment and stowage management requirements; loose equipment and stowage data base information requirements; spacecraft loose equipment stowage drawing requirements; and inflight stowage management data requirements. Additional data was developed defining inflight maintenance processes and related data concepts for inflight troubleshooting, remove/repair/replace and scheduled maintenance activities. The process of maintenance task and equipment definition during spacecraft design and development was also defined and related data concepts were identified for futher development into formal NASA specifications during future follow-on study phases of the contract.

SPHERES: From Ground Development to Operations on ISS

NASA Technical Reports Server (NTRS)

Katterhagen, A.

2015-01-01

SPHERES (Synchronized Position Hold Engage and Reorient Experimental Satellites) is an internal International Space Station (ISS) Facility that supports multiple investigations for the development of multi-spacecraft and robotic control algorithms. The SPHERES Facility on ISS is managed and operated by the SPHERES National Lab Facility at NASA Ames Research Center (ARC) at Moffett Field California. The SPHERES Facility on ISS consists of three self-contained eight-inch diameter free-floating satellites which perform the various flight algorithms and serve as a platform to support the integration of experimental hardware. To help make science a reality on the ISS, the SPHERES ARC team supports a Guest Scientist Program (GSP). This program allows anyone with new science the possibility to interface with the SPHERES team and hardware. In addition to highlighting the available SPHERES hardware on ISS and on the ground, this presentation will also highlight ground support, facilities, and resources available to guest researchers. Investigations on the ISS evolve through four main phases: Strategic, Tactical, Operations, and Post Operations. The Strategic Phase encompasses early planning beginning with initial contact by the Principle Investigator (PI) and the SPHERES program who may work with the PI to assess what assistance the PI may need. Once the basic parameters are understood, the investigation moves to the Tactical Phase which involves more detailed planning, development, and testing. Depending on the nature of the investigation, the tactical phase may be split into the Lab Tactical Phase or the ISS Tactical Phase due to the difference in requirements for the two destinations. The Operations Phase is when the actual science is performed; this can be either in the lab, or on the ISS. The Post Operations Phase encompasses data analysis and distribution, and generation of summary status and reports. The SPHERES Operations and Engineering teams at ARC is composed of experts who can guide the Payload Developer (PD) and Principle Investigator (PI) in reaching critical milestones to make their science a reality using the SPHERES platform. From performing integrated safety and verification assessments, to assisting in developing crew procedures and operations products, to organizing, planning, and executing all test sessions, to helping manage data products, the SPHERES team at ARC is available to support microgravity research with the SPEHRES Guest Scientist Program.

Automotive Stirling engine Market and Industrial Readiness Program (MIRP), phase 1

NASA Astrophysics Data System (ADS)

1982-05-01

A program, begun in 1978, has the goal of transferring Stirling engine technology from United Stirling of Sweden to the US and, then, following design, fabrication, and prototype testing, to secure US manufacturers for the engine. The ultimate objective is the large-scale commercial use of the Automotive Stirling Engine (ASE) by the year 2000. The fist phase of the Market and Industrial Readiness Program for the ASE was concerned with defining the market, product, economic and technical factors necessary to be addressed to assure a reasonable chance of ultimate commercial acceptance. Program results for this first phase are reported and discussed. These results pertain to licensing strategy development, economic analysis, market factors, product planning, market growth, cost studies, and engine performance as measured by fuel economy using conventional fuels and by vehicle speed and acceleration characteristics.

Phenol-Catalyzed Discharge in the Aprotic Lithium-Oxygen Battery.

PubMed

Gao, Xiangwen; Jovanov, Zarko P; Chen, Yuhui; Johnson, Lee R; Bruce, Peter G

2017-06-01

Discharge in the lithium-O 2 battery is known to occur either by a solution mechanism, which enables high capacity and rates, or a surface mechanism, which passivates the electrode surface and limits performance. The development of strategies to promote solution-phase discharge in stable electrolyte solutions is a central challenge for development of the lithium-O 2 battery. Here we show that the introduction of the protic additive phenol to ethers can promote a solution-phase discharge mechanism. Phenol acts as a phase-transfer catalyst, dissolving the product Li 2 O 2 , avoiding electrode passivation and forming large particles of Li 2 O 2 product-vital requirements for high performance. As a result, we demonstrate capacities of over 9 mAh cm -2 areal , which is a 35-fold increase in capacity compared to without phenol. We show that the critical requirement is the strength of the conjugate base such that an equilibrium exists between protonation of the base and protonation of Li 2 O 2 . © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Analysis on the Oversize Blast Furnace Desulfurization and a Sulfide Capacity Prediction Model Based on Congregated Electron Phase

NASA Astrophysics Data System (ADS)

Zhenyang, Wang; Jianliang, Zhang; Gang, An; Zhengjian, Liu; Zhengming, Cheng; Junjie, Huang; Jingwei, Zhang

2016-02-01

Through analyzed and regressed the actual productive desulfurization data from the oversize blast furnace (5500 m3) in north China, the relationship between the sulfur distribution parameters and the slag composition in actual production situation was investigated. As the slag and hot metal phases have their own balance sulfur content or sulfur partial pressure in gas phase, respectively, the non-equilibrium of sulfur among gas, slag, and metal phases leads to the transmission and distribution of sulfur. Combined with sulfur transmission reactions between gas, slag and metal phases, C/CO pairs equilibrium, and Wagner model, the measured sulfide capacity can be acquired using sulfur distribution ratio, sulfur activity coefficient, and oxygen activity in hot metal. Based on the theory of congregated electron phase, a new sulfide capacity prediction model (CEPM) has been developed, which has a good liner relationship with the measured sulfide capacity. Thus, using the burden structure for BF, the ironmaking slag composition can be obtained simply and can be used to reliably predict the ironmaking slag desulfurization ability a few hours later after charging under a certain temperature by CEPM.

Generation of an annotated reference standard for vaccine adverse event reports.

PubMed

Foster, Matthew; Pandey, Abhishek; Kreimeyer, Kory; Botsis, Taxiarchis

2018-07-05

As part of a collaborative project between the US Food and Drug Administration (FDA) and the Centers for Disease Control and Prevention for the development of a web-based natural language processing (NLP) workbench, we created a corpus of 1000 Vaccine Adverse Event Reporting System (VAERS) reports annotated for 36,726 clinical features, 13,365 temporal features, and 22,395 clinical-temporal links. This paper describes the final corpus, as well as the methodology used to create it, so that clinical NLP researchers outside FDA can evaluate the utility of the corpus to aid their own work. The creation of this standard went through four phases: pre-training, pre-production, production-clinical feature annotation, and production-temporal annotation. The pre-production phase used a double annotation followed by adjudication strategy to refine and finalize the annotation model while the production phases followed a single annotation strategy to maximize the number of reports in the corpus. An analysis of 30 reports randomly selected as part of a quality control assessment yielded accuracies of 0.97, 0.96, and 0.83 for clinical features, temporal features, and clinical-temporal associations, respectively and speaks to the quality of the corpus. Copyright © 2018 Elsevier Ltd. All rights reserved.

Safety and efficacy of personal care products containing colloidal oatmeal.

PubMed

Criquet, Maryline; Roure, Romain; Dayan, Liliane; Nollent, Virginie; Bertin, Christiane

2012-01-01

Colloidal oatmeal is a natural ingredient used in the formulation of a range of personal care products for relief of skin dryness and itchiness. It is also used as an adjunctive product in atopic dermatitis. The safety of personal care products used on vulnerable skin is of particular importance and the risk of developing further skin irritations and/or allergies should be minimized. In a series of studies, we tested the safety of personal care products containing oatmeal (creams, cleansers, lotions) by assessing their irritant/allergenic potential on repeat insult patch testing, in safety-in-use and ocular studies using subjects with nonsensitive and sensitive skin. We also tested the skin moisturizing and repair properties of an oatmeal-containing skin care product for dry skin. We found that oatmeal-containing personal care products had very low irritant potential as well as a very low allergenic sensitization potential. Low-level reactions were documented in 1.0% of subjects during the induction phase of repeat insult patch testing; one of 2291 subjects developed a persistent but doubtful low-level reaction involving edema during the challenge phase in repeat insult patch testing. No allergies were reported by 80 subjects after patch testing after in-use application. Sustained skin moisturizing was documented in subjects with dry skin that lasted up to 2 weeks after product discontinuation. Our results demonstrate that colloidal oatmeal is a safe and effective ingredient in personal care products. No allergies were reported by consumers of 445,820 products sold during a 3-year period.

Safety and efficacy of personal care products containing colloidal oatmeal

PubMed Central

Criquet, Maryline; Roure, Romain; Dayan, Liliane; Nollent, Virginie; Bertin, Christiane

2012-01-01

Background Colloidal oatmeal is a natural ingredient used in the formulation of a range of personal care products for relief of skin dryness and itchiness. It is also used as an adjunctive product in atopic dermatitis. The safety of personal care products used on vulnerable skin is of particular importance and the risk of developing further skin irritations and/or allergies should be minimized. Methods In a series of studies, we tested the safety of personal care products containing oatmeal (creams, cleansers, lotions) by assessing their irritant/allergenic potential on repeat insult patch testing, in safety-in-use and ocular studies using subjects with nonsensitive and sensitive skin. We also tested the skin moisturizing and repair properties of an oatmeal-containing skin care product for dry skin. Results We found that oatmeal-containing personal care products had very low irritant potential as well as a very low allergenic sensitization potential. Low-level reactions were documented in 1.0% of subjects during the induction phase of repeat insult patch testing; one of 2291 subjects developed a persistent but doubtful low-level reaction involving edema during the challenge phase in repeat insult patch testing. No allergies were reported by 80 subjects after patch testing after in-use application. Sustained skin moisturizing was documented in subjects with dry skin that lasted up to 2 weeks after product discontinuation. Conclusion Our results demonstrate that colloidal oatmeal is a safe and effective ingredient in personal care products. No allergies were reported by consumers of 445,820 products sold during a 3-year period. PMID:23204849

Development of a Ground Test and Analysis Protocol to Support NASA's NextSTEP Phase 2 Habitation Concepts

NASA Technical Reports Server (NTRS)

Beaton, Kara H.; Chappell, Steven P.; Bekdash, Omar S.; Gernhardt, Michael L.

2018-01-01

The NASA Next Space Technologies for Exploration Partnerships (NextSTEP) program is a public-private partnership model that seeks commercial development of deep space exploration capabilities to support extensive human spaceflight missions around and beyond cislunar space. NASA first issued the Phase 1 NextSTEP Broad Agency Announcement to U.S. industries in 2014, which called for innovative cislunar habitation concepts that leveraged commercialization plans for low Earth orbit. These habitats will be part of the Deep Space Gateway (DSG), the cislunar space station planned by NASA for construction in the 2020s. In 2016, Phase 2 of the NextSTEP program selected five commercial partners to develop ground prototypes. A team of NASA research engineers and subject matter experts have been tasked with developing the ground test protocol that will serve as the primary means by which these Phase 2 prototype habitats will be evaluated. Since 2008, this core test team has successfully conducted multiple spaceflight analog mission evaluations utilizing a consistent set of operational products, tools, methods, and metrics to enable the iterative development, testing, analysis, and validation of evolving exploration architectures, operations concepts, and vehicle designs. The purpose of implementing a similar evaluation process for the NextSTEP Phase 2 Habitation Concepts is to consistently evaluate the different commercial partner ground prototypes to provide data-driven, actionable recommendations for Phase 3.

Quenching ilmenite with a high-temperature and high-pressure phase using super-high-energy ball milling

PubMed Central

Hashishin, Takeshi; Tan, Zhenquan; Yamamoto, Kazuhiro; Qiu, Nan; Kim, Jungeum; Numako, Chiya; Naka, Takashi; Valmalette, Jean Christophe; Ohara, Satoshi

2014-01-01

The mass production of highly dense oxides with high-temperature and high-pressure phases allows us to discover functional properties that have never been developed. To date, the quenching of highly dense materials at the gramme-level at ambient atmosphere has never been achieved. Here, we provide evidence of the formation of orthorhombic Fe2TiO4 from trigonal FeTiO3 as a result of the high-temperature (>1250 K) and high-pressure (>23 GPa) condition induced by the high collision energy of 150 gravity generated between steel balls. Ilmenite was steeply quenched by the surrounding atmosphere, when iron-rich ilmenite (Fe2TiO4) with a high-temperature and high-pressure phase was formed by planetary collisions and was released from the collision points between the balls. Our finding allows us to infer that such intense planetary collisions induced by high-energy ball milling contribute to the mass production of a high-temperature and high-pressure phase. PMID:24763088

Quenching ilmenite with a high-temperature and high-pressure phase using super-high-energy ball milling.

PubMed

Hashishin, Takeshi; Tan, Zhenquan; Yamamoto, Kazuhiro; Qiu, Nan; Kim, Jungeum; Numako, Chiya; Naka, Takashi; Valmalette, Jean Christophe; Ohara, Satoshi

2014-04-25

The mass production of highly dense oxides with high-temperature and high-pressure phases allows us to discover functional properties that have never been developed. To date, the quenching of highly dense materials at the gramme-level at ambient atmosphere has never been achieved. Here, we provide evidence of the formation of orthorhombic Fe2TiO4 from trigonal FeTiO3 as a result of the high-temperature (>1250 K) and high-pressure (>23 GPa) condition induced by the high collision energy of 150 gravity generated between steel balls. Ilmenite was steeply quenched by the surrounding atmosphere, when iron-rich ilmenite (Fe2TiO4) with a high-temperature and high-pressure phase was formed by planetary collisions and was released from the collision points between the balls. Our finding allows us to infer that such intense planetary collisions induced by high-energy ball milling contribute to the mass production of a high-temperature and high-pressure phase.

Methyl Chloroform Elimination from the Production of Space Shuttle Sold Rocket Motors

NASA Technical Reports Server (NTRS)

Golde, Rick P.; Burt, Rick; Key, Leigh

1997-01-01

Thiokol Space Operations manufactures the Reusable Solid Rocket Motors used to launch America's fleet of Space Shuttles. In 1989, Thiokol used more than 1.4 Mlb of methyl chloroform to produce rocket motors. The ban placed by the Environmental Protection Agency on the sale of methyl chloroform had a significant effect on future Reusable Solid Rocket Motor production. As a result, changes in the materials and processes became necessary. A multiphased plan was established by Thiokol in partnership with NASA's Marshall Space Flight Center to eliminate the use of methyl chloroform in the Reusable Solid Rocket Motor production process. Because of the extensive scope of this effort, the plan was phased to target the elimination of the majority of methyl chloroform use (90 percent) by January 1, 1996, the 3 Environmental Protection Agency deadline. Referred to as Phase I, this effort includes the elimination of two large vapor degreasers, grease diluent processes, and propellant tooling handcleaning using methyl chloroform. Meanwhile, a request was made for an essential use exemption to allow the continued use of the remaining 10 percent of methyl chloroform after the 1996 deadline, while total elimination was pursued for this final, critical phase (Phase II). This paper provides an update to three previous presentations prepared for the 1993, 1994, and 1995 CFC/Halon Alternative Conferences, and will outline the overall Ozone Depleting Compounds Elimination Program from the initial phases through the final testing and implementation phases, including facility and equipment development. Processes and materials to be discussed include low-pressure aqueous wash systems, high-pressure water blast systems- environmental shipping containers, aqueous and semi-aqueous cleaning solutions, and bond integrity and inspection criteria. Progress toward completion of facility implementation and lessons learned during the scope of the program, as well as the current development efforts and basic requirements of future methyl chloroform handcleaning elimination, will also be outlined.

In-Line Monitoring of Fab Processing Using X-Ray Diffraction

NASA Astrophysics Data System (ADS)

Gittleman, Bruce; Kozaczek, Kris

2005-09-01

As the materials shift that started with Cu continues to advance in the semiconductor industry, new issues related to materials microstructure have arisen. While x-ray diffraction (XRD) has long been used in development applications, in this paper we show that results generated in real time by a unique, high throughput, fully automated XRD metrology tool can be used to develop metrics for qualification and monitoring of critical processes in current and future manufacturing. It will be shown that these metrics provide a unique set of data that correlate to manufacturing issues. For example, ionized-sputtering is the current deposition method of choice for both the Cu seed and TaNx/Ta barrier layers. The alpha phase of Ta is widely used in production for the upper layer of the barrier stack, but complete elimination of the beta phase requires a TaNx layer with sufficient N content, but not so much as to start poisoning the target and generating particle issues. This is a well documented issue, but traditional monitoring by sheet resistance methods cannot guarantee the absence of the beta phase, whereas XRD can determine the presence of even small amounts of beta. Nickel silicide for gate metallization is another example where monitoring of phase is critical. As well being able to qualify an anneal process that gives only the desired NiSi phase everywhere across the wafer, XRD can be used to determine if full silicidation of the Ni has occurred and characterize the crystallographic microstructure of the Ni to determine any effect of that microstructure on the anneal process. The post-anneal nickel silicide phase and uniformity of the silicide microstructure can all be monitored in production. Other examples of the application of XRD to process qualification and production monitoring are derived from the dependence of certain processes, some types of defect generation, and device performance on crystallographic texture. The data presented will show that CMP dishing problems could be traced to texture of the barrier layer and mitigated by adjusting the barrier process. The density of pits developed during CMP of electrochemically deposited (ECD) Cu depends on the fraction of (111) oriented grains. It must be emphasized that the crystallographic texture is not only a key parameter for qualification of high yielding and reliable processes, but also serves as a critical parameter for monitoring tool health. The texture of Cu and W are sensitive not only to deviations in performance of the tool depositing or annealing a particular film, but also highly sensitive to the texture of the barrier underlayers and thus any performance deviations in those tools. The XRD metrology tool has been designed with production monitoring in mind and has been fully integrated into both 200 mm and 300 mm fabs. Rapid analysis is achieved by using a high intensity fixed x-ray source, coupled with a large area 2D detector. The output metrics from one point are generated while the tool is measuring a subsequent point, giving true on-the-fly analysis; no post-processing of data is necessary. Spatial resolution on the wafer surface ranging from 35 μm to 1 mm is available, making the tool suitable for monitoring of product wafers. Typical analysis times range from 10 seconds to 2 minutes per point, depending on the film thickness and spot size. Current metrics used for process qualification and production monitoring are phase, FWHM of the primary phase peaks (for mean grain size tracking), and crystallographic texture.

Development of a Production Ready Automated Wire Delivery System

NASA Technical Reports Server (NTRS)

1997-01-01

The current development effort is a Phase 3 research study entitled "A Production Ready Automated Wire Delivery System", contract number NAS8-39933, awarded to Nichols Research Corporation (NRC). The goals of this research study were to production harden the existing Automated Wire Delivery (AWDS) motion and sensor hardware and test the modified AWDS in a range of welding applications. In addition, the prototype AWDS controller would be moved to the VME bus platform by designing, fabricating and testing a single board VME bus AWDS controller. This effort was to provide an AWDS that could transition from the laboratory environment to production operations. The project was performed in two development steps. Step 1 modified and tested an improved MWG. Step 2 developed and tested the AWDS single board VME bus controller. Step 3 installed the Wire Pilot in a Weld Controller with the imbedded VME bus controller.

Factors Affecting Exocellular Polysaccharide Production by Lactobacillus delbrueckii subsp. bulgaricus Grown in a Chemically Defined Medium†

PubMed Central

Petry, Sandrine; Furlan, Sylviane; Crepeau, Marie-Jeanne; Cerning, Jutta; Desmazeaud, Michel

2000-01-01

We developed a chemically defined medium (CDM) containing lactose or glucose as the carbon source that supports growth and exopolysaccharide (EPS) production of two strains of Lactobacillus delbrueckii subsp. bulgaricus. The factors found to affect EPS production in this medium were oxygen, pH, temperature, and medium constituents, such as orotic acid and the carbon source. EPS production was greatest during the stationary phase. Composition analysis of EPS isolated at different growth phases and produced under different fermentation conditions (varying carbon source or pH) revealed that the component sugars were the same. The EPS from strain L. delbrueckii subsp. bulgaricus CNRZ 1187 contained galactose and glucose, and that of strain L. delbrueckii subsp. bulgaricus CNRZ 416 contained galactose, glucose, and rhamnose. However, the relative proportions of the individual monosaccharides differed, suggesting that repeating unit structures can vary according to specific medium alterations. Under pH-controlled fermentation conditions, L. delbrueckii subsp. bulgaricus strains produced as much EPS in the CDM as in milk. Furthermore, the relative proportions of individual monosaccharides of EPS produced in pH-controlled CDM or in milk were very similar. The CDM we developed may be a useful model and an alternative to milk in studies of EPS production. PMID:10919802

Development and Validation of an RP-HPLC Method for the Determination of Vinpocetine and Folic Acid in the Presence of a Vinpocetine Alkaline Degradation Product in Bulk and in Capsule Form.

PubMed

Elkady, Ehab F; Tammam, Marwa H; Mohamed, Ayman A

2017-05-01

An alkaline-forced degradation hydrolytic product of vinpocetine was prepared and characterized by 1H-NMR, FTIR spectroscopy, and MS. Subsequently, a simple, selective, and validated reversed-phase HPLC method was developed for the simultaneous estimation of vinpocetine and folic acid in the presence of a vinpocetine alkaline degradation product. Chromatographic separation was achieved using an isocratic mobile phase consisting of acetonitrile-0.02 M KH2PO4 [containing 0.2% (v/v) triethylamine and adjusted to pH 6 with orthophosphoric acid; (80 + 20, v/v)] at a flow rate of 0.9 mL/min at ambient temperature on a Eurospher II C18 (250 × 4.6 mm, 5 μm) column, with UV detection at 280 nm for folic acid and 230 nm for vinpocetine and its alkaline hydrolytic product. Linearity, accuracy, and precision were found to be acceptable over a concentration range of 12.5-200 μg/mL for vinpocetine and 1-16 μg/mL for folic acid. The proposed method was successfully applied for the determination of both drugs and a vinpocetine hydrolysis product in a laboratory-prepared mixture and in a capsule containing both drugs.

Biogas production enhancement using semi-aerobic pre-aeration in a hybrid bioreactor landfill.

PubMed

Cossu, Raffaello; Morello, Luca; Raga, Roberto; Cerminara, Giulia

2016-09-01

Landfilling continues to be one of the main methods used in managing Municipal Solid Waste (MSW) worldwide, particularly in developing countries. Although in many countries national legislation aims to reduce this practice as much as possible, landfill is a necessary and unavoidable step in closing the material cycle. The need for innovative waste management techniques to improve landfill management and minimize the adverse environmental impact produced has resulted in an increasing interest in innovative systems capable of accelerating waste stabilization. Landfill bioreactors allow decomposition kinetics to be increased and post-operational phase to be shortened; in particular, hybrid bioreactors combine the benefits afforded by both aerobic and anaerobic processes. Six bioreactor simulators were used in the present study: four managed as hybrid, with an initial semi-aerobic phase and a second anaerobic phase, and two as anaerobic control bioreactors. The main goal of the first aerated phase is to reduce Volatile Fatty Acids (VFA) in order to increase pH and enhance methane production during the anaerobic phase; for this reason, air injection was stopped only when these parameters reached the optimum range for methanogenic bacteria. Biogas and leachate were constantly monitored throughout the entire methanogenic phase with the aim of calibrating a Gompertz Model and evaluating the effects of pre-aeration on subsequent methane production. The results showed that moderate and intermittent pre-aeration produces a positive effect both on methane potential and in the kinetics of reaction. Copyright © 2015 Elsevier Ltd. All rights reserved.

A Human-Centered Design Methodology to Enhance the Usability, Human Factors, and User Experience of Connected Health Systems: A Three-Phase Methodology.

PubMed

Harte, Richard; Glynn, Liam; Rodríguez-Molinero, Alejandro; Baker, Paul Ma; Scharf, Thomas; Quinlan, Leo R; ÓLaighin, Gearóid

2017-03-16

Design processes such as human-centered design, which involve the end user throughout the product development and testing process, can be crucial in ensuring that the product meets the needs and capabilities of the user, particularly in terms of safety and user experience. The structured and iterative nature of human-centered design can often present a challenge when design teams are faced with the necessary, rapid, product development life cycles associated with the competitive connected health industry. We wanted to derive a structured methodology that followed the principles of human-centered design that would allow designers and developers to ensure that the needs of the user are taken into account throughout the design process, while maintaining a rapid pace of development. In this paper, we present the methodology and its rationale before outlining how it was applied to assess and enhance the usability, human factors, and user experience of a connected health system known as the Wireless Insole for Independent and Safe Elderly Living (WIISEL) system, a system designed to continuously assess fall risk by measuring gait and balance parameters associated with fall risk. We derived a three-phase methodology. In Phase 1 we emphasized the construction of a use case document. This document can be used to detail the context of use of the system by utilizing storyboarding, paper prototypes, and mock-ups in conjunction with user interviews to gather insightful user feedback on different proposed concepts. In Phase 2 we emphasized the use of expert usability inspections such as heuristic evaluations and cognitive walkthroughs with small multidisciplinary groups to review the prototypes born out of the Phase 1 feedback. Finally, in Phase 3 we emphasized classical user testing with target end users, using various metrics to measure the user experience and improve the final prototypes. We report a successful implementation of the methodology for the design and development of a system for detecting and predicting falls in older adults. We describe in detail what testing and evaluation activities we carried out to effectively test the system and overcome usability and human factors problems. We feel this methodology can be applied to a wide variety of connected health devices and systems. We consider this a methodology that can be scaled to different-sized projects accordingly. ©Richard Harte, Liam Glynn, Alejandro Rodríguez-Molinero, Paul MA Baker, Thomas Scharf, Leo R Quinlan, Gearóid ÓLaighin. Originally published in JMIR Human Factors (http://humanfactors.jmir.org), 16.03.2017.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flanigan, Tom; Pybus, Craig; Roy, Sonya

This report summarizes the results of the Pre-Front End Engineering Design (pre-FEED) phase of a proposed advanced oxy-combustion power generation plant to repower the existing 200 MWe Unit 4 at Ameren Energy Resources’ (AER) Meredosia Power Plant. AER has formed an alliance with Air Liquide Process and Construction, Inc. (ALPC) and Babcock & Wilcox Power Generation Group (B&W PGG) for the design, construction, and testing of the facility, and has contracted with URS Corporation (URS) for preliminary design and Owner’s engineering services. The Project employs oxy-combustion technology – combustion of coal with nearly pure oxygen and recycled flue gas (insteadmore » of air) – to capture approximately 90% of the flue gas CO2 for transport and sequestration by another Project. Plant capacity and configuration has been developed based on the B&W PGG-ALPC cool recycle process firing high-sulfur bituminous coal fuel, assuming baseload plant operation to maximize existing steam turbine capability, with limited consideration for plant redundancy and performance optimization in order to keep plant costs as low as practical. Activities and preliminary results from the pre-FEED phase addressed in this report include the following: Overall plant thermal performance; Equipment sizing and system configuration; Plant operation and control philosophy; Plant emissions and effluents; CO 2 production and recovery characteristics; Project cost estimate and economic evaluation; Integrated project engineering and construction schedule; Project risk and opportunity assessment; Development of Project permitting strategy and requirements During the Phase 2 of the Project, additional design details will be developed and the Phase 1 work products updated to support actual construction and operation of the facility in Phase 3. Additional information will be provided early in Phase 2 to support Ameren-Environmental in finalizing the appropriate permitting strategies and permit applications. Additional performance and reliability enhancements will also be evaluated in Phase 2 to try to improve overall project economics.« less

Kr ion irradiation study of the depleted-uranium alloys

NASA Astrophysics Data System (ADS)

Gan, J.; Keiser, D. D.; Miller, B. D.; Kirk, M. A.; Rest, J.; Allen, T. R.; Wachs, D. M.

2010-12-01

Fuel development for the reduced enrichment research and test reactor (RERTR) program is tasked with the development of new low enrichment uranium nuclear fuels that can be employed to replace existing high enrichment uranium fuels currently used in some research reactors throughout the world. For dispersion type fuels, radiation stability of the fuel-cladding interaction product has a strong impact on fuel performance. Three depleted-uranium alloys are cast for the radiation stability studies of the fuel-cladding interaction product using Kr ion irradiation to investigate radiation damage from fission products. SEM analysis indicates the presence of the phases of interest: U(Al, Si) 3, (U, Mo)(Al, Si) 3, UMo 2Al 20, U 6Mo 4Al 43 and UAl 4. Irradiations of TEM disc samples were conducted with 500 keV Kr ions at 200 °C to ion doses up to 2.5 × 10 19 ions/m 2 (˜10 dpa) with an Kr ion flux of 10 16 ions/m 2/s (˜4.0 × 10 -3 dpa/s). Microstructural evolution of the phases relevant to fuel-cladding interaction products was investigated using transmission electron microscopy.

Formulation and characterization of polymeric films containing combinations of antiretrovirals (ARVs) for HIV prevention.

PubMed

Akil, Ayman; Agashe, Hrushikesh; Dezzutti, Charlene S; Moncla, Bernard J; Hillier, Sharon L; Devlin, Brid; Shi, Yuan; Uranker, Kevin; Rohan, Lisa Cencia

2015-02-01

To develop polymeric films containing dual combinations of anti-HIV drug candidate tenofovir, maraviroc and dapivirine for vaginal application as topical microbicides. A solvent casting method was used to manufacture the films. Solid phase solubility was used to identify potential polymers for use in the film formulation. Physical and chemical properties (such as water content, puncture strength and in vitro release) and product stability were determined. The bioactivity of the film products against HIV was assessed using the TZM-bl assay and a cervical explant model. Polymers identified from the solid phase solubility study maintained tenofovir and maraviroc in an amorphous state and prevented drug crystallization. Three combination film products were developed using cellulose polymers and polyvinyl alcohol. The residual water content in all films was <10% (w/w). All films delivered the active agents with release of >50% of film drug content within 30 min. Stability testing confirmed that the combination film products were stable for 12 months at ambient temperature and 6 months under stressed conditions. Antiviral activity was confirmed in TZM-bl and cervical explant models. Polymeric films can be used as a stable dosage form for the delivery of antiretroviral combinations as microbicides.

Composition and functional property of photosynthetic pigments under circadian rhythm in the cyanobacterium Spirulina platensis.

PubMed

Kumar, Deepak; Kannaujiya, Vinod K; Richa; Pathak, Jainendra; Sundaram, Shanthy; Sinha, Rajeshwar P

2018-05-01

Circadian rhythm is an important endogenous biological signal for sustainable growth and development of cyanobacteria in natural ecosystems. Circadian effects of photosynthetically active radiation (PAR), ultraviolet-A (UV-A) and ultraviolet-B (UV-B) radiations on pigment composition have been studied in the cyanobacterium Spirulina platensis under light (L)/dark (D) oscillation with a combination of 4/20, 8/16, 12/12, 16/8, 20/4 and 24/24 h time duration. Circadian exposure of PAR + UV-A (PA) and PAR + UV-A + UV-B (PAB) showed more than twofold decline in Chl a, total protein and phycocyanin (PC) in light phase and significant recovery was achieved in dark phase. The fluorescence emission wavelength of PC was shifted towards lower wavelengths in the light phase of PAB in comparison to P and PA whereas the same wavelength was retrieved in the dark phase. The production of free radicals was accelerated twofold in the light phase (24 h L) whereas the same was retrieved to the level of control during the dark phase. Oxidatively induced damage was alleviated by antioxidative enzymes such as catalase (CAT), peroxidase (POD), superoxide dismutase (SOD) and ascorbate peroxidase (APX) in the light phase (0-24-h L) whereas the dark phase showed significant inhibition of the same enzymes. Similar characteristic inhibition of free radicals and recovery of PC was observed inside cellular filament after circadian rhythm of 24/24 h (L/D). Circadian exposure of P, PA and PAB significantly altered the synthesis and recovery of pigments that could be crucial for optimization and sustainable production of photosynthetic products for human welfare.

Recovery Act: Beneficial CO{sub 2} Capture in an Integrated Algal Biorefinery for Renewable Generation and Transportation Fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lane, Christopher; Hampel, Kristin; Rismani-Yazdi, Hamid

DOE DE-FE0001888 Award, Phase 2, funded research, development, and deployment (RD&D) of Phycal’s pilot-scale, algae to biofuels, bioproducts, and processing facility in Hawai’i. Phycal’s algal-biofuel and bioproducts production system integrates several novel and mature technologies into a system that captures and reuses industrially produced carbon dioxide emissions, which would otherwise go directly to the atmosphere, for the manufacture of renewable energy products and bioproducts from algae (note that these algae are not genetically engineered). At the end of Phase 2, the project as proposed was to encompass 34 acres in Central Oahu and provide large open ponds for algal massmore » culturing, heterotrophic reactors for the Heteroboost™ process, processing facilities, water recycling facilities, anaerobic digestion facilities, and other integrated processes. The Phase 2 award was divided into two modules, Modules 1 & 2, where the Module 1 effort addressed critical scaling issues, tested highest risk technologies, and set the overall infrastructure needed for a Module 2. Phycal terminated the project prior to executing construction of the first Module. This Final Report covers the development research, detailed design, and the proposed operating strategy for Module 1 of Phase 2.« less

Recovery of Navy distillate fuel from reclaimed product. Volume II. Literature review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brinkman, D.W.; Whisman, M.L.

In an effort to assist the Navy to better utilize its waste hydrocarbons, NIPER, with support from the US Department of Energy, is conducting research designed to ultimately develop a practical technique for converting Reclaimed Product (RP) into specification Naval Distillate Fuel (F-76). This first phase of the project was focused on reviewing the literature and available information from equipment manufacturers. The literature survey has been carefully culled for methodology applicable to the conversion of RP into diesel fuel suitable for Navy use. Based upon the results of this study, a second phase has been developed and outlined in whichmore » experiments will be performed to determine the most practical recycling technologies. It is realized that the final selection of one particular technology may be site-specific due to vast differences in RP volume and available facilities. A final phase, if funded, would involve full-scale testing of one of the recommended techniques at a refueling depot. The Phase I investigations are published in two volumes. Volume 1, Technical Discussion, includes the narrative and Appendices I and II. Appendix III, a detailed Literature Review, includes both a narrative portion and an annotated bibliography containing about 800 references and abstracts. This appendix, because of its volume, has been published separately as Volume 2.« less

Boarding Team Communications Phase I: Product Development and Evaluation

DTIC Science & Technology

2007-05-01

U.S. Coast Guard Research and Development Center 1082 Shennecossett Road, Groton, CT 06340-6048 Report No. CG-D-04-2007 Template: Report Cover...Technical Director United States Coast Guard Research & Development Center 1082 Shennecossett Road Groton, CT 06340-6048 Template...Research and Development Center 11. Contract or Grant No. 1082 Shennecossett Road Fairfax, VA 22030 Groton, CT 06340-6048 13. Type of

Fostering creativity in product and service development: validation in the domain of information technology.

PubMed

Zeng, Liang; Proctor, Robert W; Salvendy, Gavriel

2011-06-01

This research is intended to empirically validate a general model of creative product and service development proposed in the literature. A current research gap inspired construction of a conceptual model to capture fundamental phases and pertinent facilitating metacognitive strategies in the creative design process. The model also depicts the mechanism by which design creativity affects consumer behavior. The validity and assets of this model have not yet been investigated. Four laboratory studies were conducted to demonstrate the value of the proposed cognitive phases and associated metacognitive strategies in the conceptual model. Realistic product and service design problems were used in creativity assessment to ensure ecological validity. Design creativity was enhanced by explicit problem analysis, whereby one formulates problems from different perspectives and at different levels of abstraction. Remote association in conceptual combination spawned more design creativity than did near association. Abstraction led to greater creativity in conducting conceptual expansion than did specificity, which induced mental fixation. Domain-specific knowledge and experience enhanced design creativity, indicating that design can be of a domain-specific nature. Design creativity added integrated value to products and services and positively influenced customer behavior. The validity and value of the proposed conceptual model is supported by empirical findings. The conceptual model of creative design could underpin future theory development. Propositions advanced in this article should provide insights and approaches to facilitate organizations pursuing product and service creativity to gain competitive advantage.

Case history of Yakin field: its development and sand control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sawolo, N.; Krueger, R.F.; Maly, G.P.

1983-01-01

This paper deals with the development of the Yakin field in East Kalimantan, Indonesia, with emphasis on the sand control methods used. Implementation of an effective sand control program ensured the successful development of this field. Gravel-packed wells had substantially lower production decline rates than the initial completions without gravel packs. Control of sand production also has been demonstrated by the lack of sand problems during the 4 1/2 years since the sand control program was initiated. During this time there have been no submersible pump failures associated with sand production. The successful sand control program was achieved by amore » well-coordinated and cooperative effort of drilling, reservoir engineering, production research, and service company personnel. Establishment of communication among all people involved, starting early in the planning process and continuing through the rig operations to the final production phase, coupled with intensive training at all levels of responsibility, on-site supervision, and quality control were important factors in the success of the development program.« less

Rationale, challenges, and participants in a Phase II trial of a botanical product for chronic hepatitis C

PubMed Central

Belle, Steven H; Fried, Michael W; Afdhal, Nezam; Navarro, Victor J; Hawke, Roy L; Wahed, Abdus S; Doo, Edward; Meyers, Catherine M

2012-01-01

Background Chronic hepatitis C is associated with significant morbidity and mortality as a consequence of progression to cirrhosis, hepatocellular carcinoma, and liver failure. Current treatment for chronic hepatitis C with pegylated interferon (IFN) and ribavirin is associated with suboptimal responses and numerous adverse effects. A number of botanical products have been used to treat hepatic disorders. Silymarin, extracted from the milk thistle plant, Silybum marianum (L) Gaertn. (Asteraceae), has been most widely used for various liver disorders, including chronic hepatitis C, B, and alcoholic liver disease. However, the safety and efficacy of silymarin have not been studied systematically in chronic hepatitis C. Purpose We describe our strategy for a phased approach for studying the impact of silymarin in hepatitis C, in the context of the unique challenges of botanical product clinical trials and the development of specific and curative antiviral therapy. Methods This multicenter, randomized, double-masked, placebo-controlled trial was conducted with four clinical centers and a data-coordinating center in the United States, to assess the impact of silymarin therapy in patients with chronic hepatitis C who failed conventional antiviral therapy. Results Key aspects relevant to performing clinical trials of botanical products include early identification of an appropriate product with standard product chemistry, acquisition of pharmacokinetic and dosing information, selection of the appropriate study group, and choosing rigorous outcome variables. Potential limitations Trial participants were chronic hepatitis C patients who were nonsustained virologic responders to IFN-based therapy; therefore, the findings are not generalizable to all hepatitis C populations. Further, alanine aminotransferase, a biochemical liver test, rather than hepatitis viral RNA or liver histology was the primary end point. Conclusions The challenges identified and addressed during development of this United States multicenter Phase II trial to evaluate silymarin for treatment of patients with chronic hepatitis C infection who had failed to respond successfully to previous IFN-based therapy are common and must be addressed to conduct rigorous trials of botanical products. PMID:22058086

Rationale, challenges, and participants in a Phase II trial of a botanical product for chronic hepatitis C.

PubMed

Reddy, K Rajender; Belle, Steven H; Fried, Michael W; Afdhal, Nezam; Navarro, Victor J; Hawke, Roy L; Wahed, Abdus S; Doo, Edward; Meyers, Catherine M

2012-02-01

Chronic hepatitis C is associated with significant morbidity and mortality as a consequence of progression to cirrhosis, hepatocellular carcinoma, and liver failure. Current treatment for chronic hepatitis C with pegylated interferon (IFN) and ribavirin is associated with suboptimal responses and numerous adverse effects. A number of botanical products have been used to treat hepatic disorders. Silymarin, extracted from the milk thistle plant, Silybum marianum (L) Gaertn. (Asteraceae), has been most widely used for various liver disorders, including chronic hepatitis C, B, and alcoholic liver disease. However, the safety and efficacy of silymarin have not been studied systematically in chronic hepatitis C. We describe our strategy for a phased approach for studying the impact of silymarin in hepatitis C, in the context of the unique challenges of botanical product clinical trials and the development of specific and curative antiviral therapy. This multicenter, randomized, double-masked, placebo-controlled trial was conducted with four clinical centers and a data-coordinating center in the United States, to assess the impact of silymarin therapy in patients with chronic hepatitis C who failed conventional antiviral therapy. Key aspects relevant to performing clinical trials of botanical products include early identification of an appropriate product with standard product chemistry, acquisition of pharmacokinetic and dosing information, selection of the appropriate study group, and choosing rigorous outcome variables. POTENTIAL LIMITATIONS: Trial participants were chronic hepatitis C patients who were nonsustained virologic responders to IFN-based therapy; therefore, the findings are not generalizable to all hepatitis C populations. Further, alanine aminotransferase, a biochemical liver test, rather than hepatitis viral RNA or liver histology was the primary end point. The challenges identified and addressed during development of this United States multicenter Phase II trial to evaluate silymarin for treatment of patients with chronic hepatitis C infection who had failed to respond successfully to previous IFN-based therapy are common and must be addressed to conduct rigorous trials of botanical products.

Evaluation of Selected Chemical Processes for Production of Low-cost Silicon, Phase 3. [using a fluidized bed reactor

NASA Technical Reports Server (NTRS)

Blocher, J. M., Jr.; Browning, M. F.

1979-01-01

The construction and operation of an experimental process system development unit (EPSDU) for the production of granular semiconductor grade silicon by the zinc vapor reduction of silicon tetrachloride in a fluidized bed of seed particles is presented. The construction of the process development unit (PDU) is reported. The PDU consists of four critical units of the EPSDU: the fluidized bed reactor, the reactor by product condenser, the zinc vaporizer, and the electrolytic cell. An experimental wetted wall condenser and its operation are described. Procedures are established for safe handling of SiCl4 leaks and spills from the EPSDU and PDU.

Innovation and industry-academia interactions: where conflicts arise and measures to avoid them.

PubMed

Vagelos, P Roy

2007-03-01

Every phase of the development of biopharmaceuticals and medical devices has the potential for conflict of interest, but adherence to established rules and practices throughout product development can eliminate the possibility of conflicts. Adherence to good practices should continue through the postmarketing period, with swift reporting and vigorous investigation of any safety concerns. Although some academic medical centers are restricting interactions between their faculty and industry to prevent possible conflicts in physician education about new products, industry and academia should look for new ways to come together in mutually agreed forums that focus on educating clinicians about new products in an efficient, transparent way.

Investigation of phase distribution using Phame® in-die phase measurements

NASA Astrophysics Data System (ADS)

Buttgereit, Ute; Perlitz, Sascha

2009-03-01

As lithography mask processes move toward 45nm and 32nm node, mask complexity increases steadily, mask specifications tighten and process control becomes extremely important. Driven by this fact the requirements for metrology tools increase as well. Efforts in metrology have been focused on accurately measuring CD linearity and uniformity across the mask, and accurately measuring phase variation on Alternating/Attenuated PSM and transmission for Attenuated PSM. CD control on photo masks is usually done through the following processes: exposure dose/focus change, resist develop and dry etch. The key requirement is to maintain correct CD linearity and uniformity across the mask. For PSM specifically, the effect of CD uniformity for both Alternating PSM and Attenuated PSM and etch depth for Alternating PSM becomes also important. So far phase measurement has been limited to either measuring large-feature phase using interferometer-based metrology tools or measuring etch depth using AFM and converting etch depth into phase under the assumption that trench profile and optical properties of the layers remain constant. However recent investigations show that the trench profile and optical property of layers impact the phase. This effect is getting larger for smaller CD's. The currently used phase measurement methods run into limitations because they are not able to capture 3D mask effects, diffraction limitations or polarization effects. The new phase metrology system - Phame(R) developed by Carl Zeiss SMS overcomes those limitations and enables laterally resolved phase measurement in any kind of production feature on the mask. The resolution of the system goes down to 120nm half pitch at mask level. We will report on tool performance data with respect to static and dynamic phase repeatability focusing on Alternating PSM. Furthermore the phase metrology system was used to investigate mask process signatures on Alternating PSM in order to further improve the overall PSM process performance. Especially global loading effects caused by the pattern density and micro loading effects caused by the feature size itself have been evaluated using the capability of measuring phase in the small production features. The results of this study will be reported in this paper.

Development of satellite remote sensing techniques as an economic tool for forestry industry

NASA Technical Reports Server (NTRS)

Sader, Steven A.; Jadkowski, Mark A.

1989-01-01

A cooperative commercial development project designed to focus on cost-effective and practical applications of satellite remote sensing in forest management is discussed. The project, initiated in September, 1988 is being executed in three phases: (1) development of a forest resource inventory and geographic information system (GIS) updating systems; (2) testing and evaluation of remote-sensing products against forest industry specifications; and (3) integration of remote-sensing services and products in an operational setting. An advisory group represented by eleven major forest-product companies will provide direct involvement of the target market. The advisory group will focus on the following questions: Does the technology work for them? How can it be packaged to provide the needed forest-management information? Can the products and information be provided in a cost-effective manner?

Quality Attribute Techniques Framework

NASA Astrophysics Data System (ADS)

Chiam, Yin Kia; Zhu, Liming; Staples, Mark

The quality of software is achieved during its development. Development teams use various techniques to investigate, evaluate and control potential quality problems in their systems. These “Quality Attribute Techniques” target specific product qualities such as safety or security. This paper proposes a framework to capture important characteristics of these techniques. The framework is intended to support process tailoring, by facilitating the selection of techniques for inclusion into process models that target specific product qualities. We use risk management as a theory to accommodate techniques for many product qualities and lifecycle phases. Safety techniques have motivated the framework, and safety and performance techniques have been used to evaluate the framework. The evaluation demonstrates the ability of quality risk management to cover the development lifecycle and to accommodate two different product qualities. We identify advantages and limitations of the framework, and discuss future research on the framework.

On the phase form of a deformation quantization with separation of variables

NASA Astrophysics Data System (ADS)

Karabegov, Alexander

2016-06-01

Given a star product with separation of variables on a pseudo-Kähler manifold, we obtain a new formal (1, 1)-form from its classifying form and call it the phase form of the star product. The cohomology class of a star product with separation of variables equals the class of its phase form. We show that the phase forms can be arbitrary and they bijectively parametrize the star products with separation of variables. We also describe the action of a change of the formal parameter on a star product with separation of variables, its formal Berezin transform, classifying form, phase form, and canonical trace density.

Site-specific synthesis of Amadori-modified peptides on solid phase.

PubMed

Frolov, Andrej; Singer, David; Hoffmann, Ralf

2006-06-01

Glycation of peptides and proteins is a slow chemical reaction of reducing sugars modifying the amino groups. The first intermediates of this nonenzymatic glycosylation are the Amadori products that can undergo further chemical reactions, finally leading to advanced glycation end products (AGEs). The formation of AGEs was not only linked to aging of tissues and organs in general but also to several diseases such as diabetes mellitus and Alzheimer's disease. Because of the importance of these modifications and their potential use as diagnostic markers, a global postsynthetic approach on solid phase was developed. The peptides were synthesized by Fmoc/(t)Bu-chemistry, with the lysine residue to be modified being protected with the very acid-labile methyltrityl group. Incubation of the peptides with D-glucose in DMF at elevated temperatures resulted in product yields of 35%. Neighboring residues with bulky protecting groups reduced the yields only slightly. The major by-products were the unmodified peptide and an oxidation product. Whereas the unmodified peptide eluted before the glycated peptide, all other by-products eluted later in RP-HPLC, allowing simple purification.

Gas production and migration in landfills and geological materials.

PubMed

Nastev, M; Therrien, R; Lefebvre, R; Gélinas, P

2001-11-01

Landfill gas, originating from the anaerobic biodegradation of the organic content of waste, consists mainly of methane and carbon dioxide, with traces of volatile organic compounds. Pressure, concentration and temperature gradients that develop within the landfill result in gas emissions to the atmosphere and in lateral migration through the surrounding soils. Environmental and safety issues associated with the landfill gas require control of off-site gas migration. The numerical model TOUGH2-LGM (Transport of Unsaturated Groundwater and Heat-Landfill Gas Migration) has been developed to simulate landfill gas production and migration processes within and beyond landfill boundaries. The model is derived from the general non-isothermal multiphase flow simulator TOUGH2, to which a new equation of state module is added. It simulates the migration of five components in partially saturated media: four fluid components (water, atmospheric air, methane and carbon dioxide) and one energy component (heat). The four fluid components are present in both the gas and liquid phases. The model incorporates gas-liquid partitioning of all fluid components by means of dissolution and volatilization. In addition to advection in the gas and liquid phase, multi-component diffusion is simulated in the gas phase. The landfill gas production rate is proportional to the organic substrate and is modeled as an exponentially decreasing function of time. The model is applied to the Montreal's CESM landfill site, which is located in a former limestone rock quarry. Existing data were used to characterize hydraulic properties of the waste and the limestone. Gas recovery data at the site were used to define the gas production model. Simulations in one and two dimensions are presented to investigate gas production and migration in the landfill, and in the surrounding limestone. The effects of a gas recovery well and landfill cover on gas migration are also discussed.

Zirconium determination by cooling curve analysis during the pyroprocessing of used nuclear fuel

NASA Astrophysics Data System (ADS)

Westphal, B. R.; Price, J. C.; Bateman, K. J.; Marsden, K. C.

2015-02-01

An alternative method to sampling and chemical analyses has been developed to monitor the concentration of zirconium in real-time during the casting of uranium products from the pyroprocessing of used nuclear fuel. The method utilizes the solidification characteristics of the uranium products to determine zirconium levels based on standard cooling curve analyses and established binary phase diagram data. Numerous uranium products have been analyzed for their zirconium content and compared against measured zirconium data. From this data, the following equation was derived for the zirconium content of uranium products:

Pupils' Readiness for Self-Regulated Learning in the Forethought Phase of Exploratory Production

ERIC Educational Resources Information Center

Metsärinne, Mika; Kallio, Manne; Virta, Kalle

2015-01-01

This article discusses pupils' readiness for self-regulation in Exploratory Production in Technology Education. In the forethought phase of Exploratory Production, pupils envision and regulate their technological production activities. Next, in the performance phase, the envisioned goals are tried and implemented through ideating, planning and…

A New Model of Sensorimotor Coupling in the Development of Speech

ERIC Educational Resources Information Center

Westermann, Gert; Miranda, Eduardo Reck

2004-01-01

We present a computational model that learns a coupling between motor parameters and their sensory consequences in vocal production during a babbling phase. Based on the coupling, preferred motor parameters and prototypically perceived sounds develop concurrently. Exposure to an ambient language modifies perception to coincide with the sounds from…

Development and Evaluation of Pretraining as an Adjunct to a Pilot Training Study.

ERIC Educational Resources Information Center

McFadden, Robert W.; And Others

The utility of the pretraining of task-relevant cognitive skills within the context of experimental research methodology was investigated in this study. A criterion referenced pretraining multi-media product was developed and applied to support the initial phase of an experimental research effort in which several instructional methods for training…

Halaven® - eribulin mesylate (analog of halichondrin B) | NCI Technology Transfer Center | TTC

Cancer.gov

Under a CRADA with NCI, Eisai Co. provided eribulin for NCI's preclinical development activities and to support NCI's Phase I clinical trials. Eisai ultimately took the product, Halaven®, to licensure.

Development of the Connecticut product evaluation database application : Phase 1B.

DOT National Transportation Integrated Search

2010-12-01

The Federal Highway Administration (FHWA), the American Association of State Highway : Transportation Officials (AASHTO) and the Transportation Research Board (TRB), a : division of the National Research Council (NRC), maintain databases to store nat...

Automatic Clustering of Rolling Element Bearings Defects with Artificial Neural Network

NASA Astrophysics Data System (ADS)

Antonini, M.; Faglia, R.; Pedersoli, M.; Tiboni, M.

2006-06-01

The paper presents the optimization of a methodology for automatic clustering based on Artificial Neural Networks to detect the presence of defects in rolling bearings. The research activity was developed in co-operation with an Italian company which is expert in the production of water pumps for automotive use (Industrie Saleri Italo). The final goal of the work is to develop a system for the automatic control of the pumps, at the end of the production line. In this viewpoint, we are gradually considering the main elements of the water pump, which can cause malfunctioning. The first elements we have considered are the rolling bearing, a very critic component for the system. The experimental activity is based on the vibration measuring of rolling bearings opportunely damaged; vibration signals are in the second phase elaborated; the third and last phase is an automatic clustering. Different signal elaboration techniques are compared to optimize the methodology.

ELT-572(v)2 DIRCM: simulation, system design and DTE process to protect ItAF platforms against ManPADS

NASA Astrophysics Data System (ADS)

Borriello, G.; Bonori, V.; Cresti, M.; Dente, E.; Ideo, L.; Mazzi, G.; Usai, A.; Tafuto, A.; Togna, F.

2014-10-01

In this paper authors provide a description of the currently deployed Man Portable Air Defense System (ManPADS) heat-seeking missiles. Principles of IR seeking and Aircraft signatures are shortly described. Basic information are listed on currently designed Infra-Red Counter Measure Systems, intended to protect Aircrafts against ManPADS. Authors provide an overview on ELT-572(v)2 DIRCM Program, funded by Italian Air Force, currently in low rate production phase. Description of the Design and Development phase, completed in Elettronica SpA in 2013, is reported. Development Test and Evaluation (DTE) Activities on ELT-572(v)2 DIRCM, jointly performed by Elettronica Spa and Italian Air Force Flight Test Centre, are shortly described. A summary of tests and some results are also discussed. Platform Installation Programs, using the low rate production units from ELT-572(v)2 DIRCM Program, are finally listed.

EPHECT I: European household survey on domestic use of consumer products and development of worst-case scenarios for daily use.

PubMed

Dimitroulopoulou, C; Lucica, E; Johnson, A; Ashmore, M R; Sakellaris, I; Stranger, M; Goelen, E

2015-12-01

Consumer products are frequently and regularly used in the domestic environment. Realistic estimates for product use are required for exposure modelling and health risk assessment. This paper provides significant data that can be used as input for such modelling studies. A European survey was conducted, within the framework of the DG Sanco-funded EPHECT project, on the household use of 15 consumer products. These products are all-purpose cleaners, kitchen cleaners, floor cleaners, glass and window cleaners, bathroom cleaners, furniture and floor polish products, combustible air fresheners, spray air fresheners, electric air fresheners, passive air fresheners, coating products for leather and textiles, hair styling products, spray deodorants and perfumes. The analysis of the results from the household survey (1st phase) focused on identifying consumer behaviour patterns (selection criteria, frequency of use, quantities, period of use and ventilation conditions during product use). This can provide valuable input to modelling studies, as this information is not reported in the open literature. The above results were further analysed (2nd phase), to provide the basis for the development of 'most representative worst-case scenarios' regarding the use of the 15 products by home-based population groups (housekeepers and retired people), in four geographical regions in Europe. These scenarios will be used for the exposure and health risk assessment within the EPHECT project. To the best of our knowledge, it is the first time that daily worst-case scenarios are presented in the scientific published literature concerning the use of a wide range of 15 consumer products across Europe. Crown Copyright © 2015. Published by Elsevier B.V. All rights reserved.

Additional EIPC Study Analysis. Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hadley, Stanton W; Gotham, Douglas J.; Luciani, Ralph L.

Between 2010 and 2012 the Eastern Interconnection Planning Collaborative (EIPC) conducted a major long-term resource and transmission study of the Eastern Interconnection (EI). With guidance from a Stakeholder Steering Committee (SSC) that included representatives from the Eastern Interconnection States Planning Council (EISPC) among others, the project was conducted in two phases. Phase 1 involved a long-term capacity expansion analysis that involved creation of eight major futures plus 72 sensitivities. Three scenarios were selected for more extensive transmission- focused evaluation in Phase 2. Five power flow analyses, nine production cost model runs (including six sensitivities), and three capital cost estimations weremore » developed during this second phase. The results from Phase 1 and 2 provided a wealth of data that could be examined further to address energy-related questions. A list of 14 topics was developed for further analysis. This paper brings together the earlier interim reports of the first 13 topics plus one additional topic into a single final report.« less

Optimization of insect cell based protein production processes - online monitoring, expression systems, scale up.

PubMed

Druzinec, Damir; Salzig, Denise; Brix, Alexander; Kraume, Matthias; Vilcinskas, Andreas; Kollewe, Christian; Czermak, Peter

2013-01-01

Due to the increasing use of insect cell based expression systems in research and industrial recombinant protein production, the development of efficient and reproducible production processes remains a challenging task. In this context, the application of online monitoring techniques is intended to ensure high and reproducible product qualities already during the early phases of process development. In the following chapter, the most common transient and stable insect cell based expression systems are briefly introduced. Novel applications of insect cell based expression systems for the production of insect derived antimicrobial peptides/proteins (AMPs) are discussed using the example of G. mellonella derived gloverin. Suitable in situ sensor techniques for insect cell culture monitoring in disposable and common bioreactor systems are outlined with respect to optical and capacitive sensor concepts. Since scale up of production processes is one of the most critical steps in process development, a conclusive overview is given about scale up aspects for industrial insect cell culture processes.

Neutron Decay with PERC: a Progress Report

NASA Astrophysics Data System (ADS)

Konrad, G.; Abele, H.; Beck, M.; Drescher, C.; Dubbers, D.; Erhart, J.; Fillunger, H.; Gösselsberger, C.; Heil, W.; Horvath, M.; Jericha, E.; Klauser, C.; Klenke, J.; Märkisch, B.; Maix, R. K.; Mest, H.; Nowak, S.; Rebrova, N.; Roick, C.; Sauerzopf, C.; Schmidt, U.; Soldner, T.; Wang, X.; Zimmer, O.; Perc Collaboration

2012-02-01

The PERC collaboration will perform high-precision measurements of angular correlations in neutron beta decay at the beam facility MEPHISTO of the Forschungs-Neutronenquelle Heinz Maier-Leibnitz in Munich, Germany. The new beam station PERC, a clean, bright, and versatile source of neutron decay products, is designed to improve the sensitivity of neutron decay studies by one order of magnitude. The charged decay products are collected by a strong longitudinal magnetic field directly from inside a neutron guide. This combination provides the highest phase space density of decay products. A magnetic mirror serves to perform precise cuts in phase space, reducing related systematic errors. The new instrument PERC is under development by an international collaboration. The physics motivation, sensitivity, and applications of PERC as well as the status of the design and preliminary results on uncertainties in proton spectroscopy are presented in this paper.

Design for Health and Well Being: Knitted Products for Diabetics

NASA Astrophysics Data System (ADS)

Gault, A.

2016-07-01

This paper will discuss the design development, manufacturing and testing of knitted products maximizing the use of new innovations in Nano- technology and the integration of Phase Changing Materials specifically for diabetics. The project identified key aspects requiring design solutions to bring improvement to the circulatory problems with specific reference to the diabetic condition. Diabetics have particular difficulty in regulating their body temperature and this can result in the condition worsening, and resulting in loss of digits or limbs. The design of products to prevent the deterioration of the diabetic condition and to help those with limb loss was developed in collaboration with a Northern Ireland diabetic consultant, a product engineer and a knitwear designer. The fusion of ideas between the stakeholders resulted in the development and manufacture of a range of products that have been successfully tested at the yarn and fabric development stage and have been proven to maintain body temperature by either cooling or warming and therefore bring improvement to health and well-being. Whilst the product has a performance element the design ideas created desirable products that not only provided solutions to the brief but also resulted in products that had further market applications.

Evolution of Plant-Made Pharmaceuticals

PubMed Central

Thomas, David R.; Penney, Claire A.; Majumder, Amrita; Walmsley, Amanda M.

2011-01-01

The science and policy of pharmaceuticals produced and/or delivered by plants has evolved over the past twenty-one years from a backyard remedy to regulated, purified products. After seemingly frozen at Phase I human clinical trials with six orally delivered plant-made vaccines not progressing past this stage over seven years, plant-made pharmaceuticals have made a breakthrough with several purified plant-based products advancing to Phase II trials and beyond. Though fraught with the usual difficulties of pharmaceutical development, pharmaceuticals made by plants have achieved pertinent milestones albeit slowly compared to other pharmaceutical production systems and are now at the cusp of reaching the consumer. Though the current economic climate begs for cautious investment as opposed to trail blazing, it is perhaps a good time to look to the future of plant-made pharmaceutical technology to assist in planning for future developments in order not to slow this technology’s momentum. To encourage continued progress, we highlight the advances made so far by this technology, particularly the change in paradigms, comparing developmental timelines, and summarizing the current status and future possibilities of plant-made pharmaceuticals. PMID:21686181

Development of a process for efficient use of CO2 from flue gases in the production of photosynthetic microorganisms.

PubMed

González-López, C V; Acién Fernández, F G; Fernández-Sevilla, J M; Sánchez Fernández, J F; Molina Grima, E

2012-07-01

A new methodology to use efficiently flue gases as CO(2) source in the production of photosynthetic microorganisms is proposed. The CO(2) is absorbed in an aqueous phase that is then regenerated by microalgae. Carbonated solutions could absorb up to 80% of the CO(2) from diluted gas reaching total inorganic carbon (TIC) concentrations up to 2.0 g/L. The pH of the solution was maintained at 8.0-10.0 by the bicarbonate/carbonate buffer, so it is compatible with biological regeneration. The absorption process was modeled and the kinetic parameters were determined. Anabaena sp. demonstrated to tolerate pH (8.0-10.0) and TIC (up to 2.0 g/L) conditions imposed by the absorption step. Experiments of regeneration of the liquid phase demonstrated the feasibility of the overall process, converting CO(2) into organic matter. The developed process avoids heating to regenerate the liquid whereas maximizing the efficiency of CO(2) use, which is relevant to achieve the commercial production of biofuels from microalgae. Copyright © 2012 Wiley Periodicals, Inc.

Using off-the-shelf medical devices for biomedical signal monitoring in a telemedicine system for emergency medical services.

PubMed

Thelen, Sebastian; Czaplik, Michael; Meisen, Philipp; Schilberg, Daniel; Jeschke, Sabina

2015-01-01

In order to study new methods of telemedicine usage in the context of emergency medical services, researchers need to prototype integrated telemedicine systems. To conduct a one-year trial phase-intended to study a new application of telemedicine in German emergency medical services-we used off-the-shelf medical devices and software to realize real-time patient monitoring within an integrated telemedicine system prototype. We demonstrate its feasibility by presenting the integrated real-time patient monitoring solution, by studying signal delay and transmission robustness regarding changing communication channel characteristics, and by evaluating issues reported by the physicians during the trial phase. Where standards like HL7 and the IEEE 11073 family are intended to enable interoperability of product grade medical devices, we show that research prototypes benefit from the use of web technologies and simple device interfaces, as they simplify product development for a manufacturer and ease integration efforts for research teams. Embracing this approach for the development of new medical devices eases the constraint to use off-the-shelf products for research trials investigating innovative use of telemedicine.

Development strategy and process models for phased automation of design and digital manufacturing electronics

NASA Astrophysics Data System (ADS)

Korshunov, G. I.; Petrushevskaya, A. A.; Lipatnikov, V. A.; Smirnova, M. S.

2018-03-01

The strategy of quality of electronics insurance is represented as most important. To provide quality, the processes sequence is considered and modeled by Markov chain. The improvement is distinguished by simple database means of design for manufacturing for future step-by-step development. Phased automation of design and digital manufacturing electronics is supposed. The MatLab modelling results showed effectiveness increase. New tools and software should be more effective. The primary digital model is proposed to represent product in the processes sequence from several processes till the whole life circle.

Deciding alternative left turn signal phases using expert systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang, E.C.P.

1988-01-01

The Texas Transportation Institute (TTI) conducted a study to investigate the feasibility of applying artificial intelligence (AI) technology and expert systems (ES) design concepts to a traffic engineering problem. Prototype systems were developed to analyze user input, evaluate various reasoning, and suggest suitable left turn phase treatment. These systems were developed using AI programming tools on IBM PC/XT/AT-compatible microcomputers. Two slightly different systems were designed using AI languages; another was built with a knowledge engineering tool. These systems include the PD PROLOG and TURBO PROLOG AI programs, as well as the INSIGHT Production Rule Language.

Simulation and mitigation of higher-order ionospheric errors in PPP

NASA Astrophysics Data System (ADS)

Zus, Florian; Deng, Zhiguo; Wickert, Jens

2017-04-01

We developed a rapid and precise algorithm to compute ionospheric phase advances in a realistic electron density field. The electron density field is derived from a plasmaspheric extension of the International Reference Ionosphere (Gulyaeva and Bilitza, 2012) and the magnetic field stems from the International Geomagnetic Reference Field. For specific station locations, elevation and azimuth angles the ionospheric phase advances are stored in a look-up table. The higher-order ionospheric residuals are computed by forming the standard linear combination of the ionospheric phase advances. In a simulation study we examine how the higher-order ionospheric residuals leak into estimated station coordinates, clocks, zenith delays and tropospheric gradients in precise point positioning. The simulation study includes a few hundred globally distributed stations and covers the time period 1990-2015. We take a close look on the estimated zenith delays and tropospheric gradients as they are considered a data source for meteorological and climate related research. We also show how the by product of this simulation study, the look-up tables, can be used to mitigate higher-order ionospheric errors in practise. Gulyaeva, T.L., and Bilitza, D. Towards ISO Standard Earth Ionosphere and Plasmasphere Model. In: New Developments in the Standard Model, edited by R.J. Larsen, pp. 1-39, NOVA, Hauppauge, New York, 2012, available at https://www.novapublishers.com/catalog/product_info.php?products_id=35812

Expedited Development of Diphenhydramine Orally Disintegrating Tablet through Integrated Crystal and Particle Engineering.

PubMed

Wang, Chenguang; Hu, Shenye; Sun, Changquan Calvin

2017-10-02

A palatable direct compression (DC) orally disintegrating tablet (ODT) product of a bitter drug, diphenhydramine (DPH), was developed using an integrated crystal and particle engineering approach. A DPH salt with a sweetener, acesulfame (Acs), DPH-Acs, was synthesized and its solid state properties were comprehensively characterized. Tablet formulation composition and compaction parameters were optimized by employing material sparing techniques. In vivo disintegration time, bitterness, and grittiness of the final ODT product, were evaluated by a taste panel. Physical stability of the ODT tablets was assessed to identify appropriate storage conditions. Phase-pure DPH-Acs exhibited significantly better tabletability and palatability than DPH-HCl. A DC formulation was designed and optimized to obtain a new ODT product with good manufacturability and excellent product characteristics, including fast in vivo disintegration, and acceptable bitterness and grittiness. A new ODT product of DPH with excellent pharmaceutical properties was successfully developed using 15 g of DPH and in two months. This example shows that integrated crystal and particle engineering is an effective approach for developing high quality ODT products using the DC process.

Critical phases in the seed development of common juniper (Juniperus communis).

PubMed

Gruwez, R; Leroux, O; De Frenne, P; Tack, W; Viane, R; Verheyen, K

2013-01-01

Common juniper (Juniperus communis L.) populations in northwest European lowlands are currently declining in size and number. An important cause of this decline is a lack of natural regeneration. Low seed viability seems to be one of the main bottlenecks in this process. Previous research revealed a negative relation between seed viability and both temperature and nitrogen deposition. Additionally, the seeds of common juniper have a variable ripening time, which possibly influences seed viability. However, the underlying mechanisms remain unresolved. In order to elucidate this puzzle, it is important to understand in which phases of seed production the main defects are situated, together with the influence of ripening time. In this study, we compared seed viability of populations with and without successful recruitment. We examined three seed phases: (i) gamete development; (ii) fertilisation and early-embryo development; and (iii) late-embryo development. After the first two phases, we found no difference in the percentage viable seeds between populations with or without recruitment. After late-embryo development, populations without recruitment showed a significantly lower percentage of viable seeds. These results suggest that late-embryo development is a bottleneck in seed development. However, the complex interaction between seed viability and ripening time suggest that the causes should be in the second seed phase, as the accelerated development of male and female gametophytes may disturb the male-female synchrony for successful mating. © 2012 German Botanical Society and The Royal Botanical Society of the Netherlands.

Accurately measuring sea level change from space: an ESA climate change initiative for MSL closure budget studies

NASA Astrophysics Data System (ADS)

Legeais, JeanFrancois; Benveniste, Jérôme

2016-07-01

Sea level is a very sensitive index of climate change and variability. Sea level integrates the ocean warming, mountain glaciers and ice sheet melting. Understanding the sea level variability and changes implies an accurate monitoring of the sea level variable at climate scales, in addition to understanding the ocean variability and the exchanges between ocean, land, cryosphere, and atmosphere. That is why Sea Level is one of the Essential Climate Variables (ECV) selected in the frame of the ESA Climate Change Initiative (CCI) program. It aims at providing long-term monitoring of the sea level ECV with regular updates, as required for climate studies. The program is now in its second phase of 3 year (following phase I during 2011-2013). The objectives are firstly to involve the climate research community, to refine their needs and collect their feedbacks on product quality. And secondly to develop, test and select the best algorithms and standards to generate an updated climate time series and to produce and validate the Sea Level ECV product. This will better answer the climate user needs by improving the quality of the Sea Level products and maintain a sustain service for an up-to-date production. This has led to the production of a first version of the Sea Level ECV which has benefited from yearly extensions and now covers the period 1993-2014. Within phase II, new altimeter standards have been developed and tested in order to reprocess the dataset with the best standards for climate studies. The reprocessed ECV will be released in summer 2016. We will present the main achievements of the ESA CCI Sea Level Project. On the one hand, the major steps required to produce the 22 years climate time series are briefly described: collect and refine the user requirements, development of adapted algorithms for climate applications and specification of the production system. On the other hand, the product characteristics are described as well as the results from product validation, performed by several groups of the ocean and climate modeling community. Efforts have also focused on the improvement of the sea level estimation in the Arctic Ocean and in coastal areas for which preliminary results suggest that significant improvements can be achieved.

Improved Biomass Cooking Stoves and Improved Stove Emission Equipment

DOE Office of Scientific and Technical Information (OSTI.GOV)

HATFIELD, MICHAEL; Still, Dean

2013-04-15

In developing countries, there is an urgent need for access to safe, efficient, and more affordable cooking technologies. Nearly 2.5 billion people currently use an open fire or traditional cookstove to prepare their meals, and recent models predict that use of biomass for cooking will continue to be the dominant energy use in rural, resource-poor households through 2030. For these families, cooking poses serious risks to health, safety, and income. An alarming 4 million people, primarily women and children, die prematurely each year from indoor and outdoor exposure to the harmful emissions released by solid fuel combustion. Use of traditionalmore » stoves can also have a significant impact on deforestation and climate change. This dire situation creates a critical need for cookstoves that significantly and verifiably reduce fuel use and emissions in order to reach protective levels for human health and the environment. Additionally, advances in the scientific equipment needed to measure and monitor stove fuel use and emissions have not kept pace with the significant need within the industry. While several testing centers in the developed world may have hundred thousand-dollar emissions testing systems, organizations in the field have had little more than a thermometer, a scale, and subjective observations to quantify the performance of stove designs. There is an urgent need for easy-to-use, inexpensive, accurate, and robust stove testing equipment for use by laboratory and field researchers around the world. ASAT and their research partner, Aprovecho Research Center (ARC), have over thirty years of experience addressing these two needs, improved cookstoves and emissions monitoring equipment, with expertise spanning the full spectrum of development from conceptual design to product manufacturing and dissemination. This includes: 1) research, design, and verification of clean biomass cookstove technology and emissions monitoring equipment; 2) mass production of quality-controlled stove and emissions equipment at levels scalable to meet global demand; and 3) global distribution through a variety of channels and partners. ARC has been instrumental in designing and improving more than 100 stove designs over the past thirty years. In the last four years, ASAT and ARC have played a key role in the production and sales of over 200,000 improved stoves in the developed and developing world. The ARC-designed emissions equipment is currently used by researchers in laboratories and field studies on five continents. During Phase I of the DOE STTR grant, ASAT and ARC worked together to apply their wealth of product development experience towards creating the next generation of improved cookstoves and emissions monitoring equipment. Highlights of Phase I for the biomass cookstove project include 1) the development of several new stove technologies that reached the DOE 50/90 benchmark; 2) fabrication of new stove prototypes by ASAT’s manufacturing partner, Shengzhou Stove Manufacturing (SSM); 3) field testing of prototype stoves with consumers in Puerto Rico and the US; and 4) the selection of three stove prototypes for further development and commercialization during Phase II. Highlights of Phase I for the emissions monitoring equipment project include: 1) creation of a new emissions monitoring equipment product, the Laboratory Emissions Monitoring System (LEMS 2) the addition of gravimetric PM measurements to the stove testing systems to meet International Standards Organization criteria; 3) the addition of a CO{sub 2} sensor and wireless 3G capability to the IAP Meter; and 4) and the improvement of sensors and signal quality on all systems. Twelve Regional Testing and Knowledge Centers purchased this equipment during the Phase I project period.« less

Hydrogen production by the engineered cyanobacterial strain Nostoc PCC 7120 ΔhupW examined in a flat panel photobioreactor system.

PubMed

Nyberg, Marcus; Heidorn, Thorsten; Lindblad, Peter

2015-12-10

Nitrogenase based hydrogen production was examined in a ΔhupW strain of the filamentous heterocystous cyanobacterium Nostoc PCC 7120, i.e., cells lacking the last step in the maturation system of the large subunit of the uptake hydrogenase and as a consequence with a non-functional uptake hydrogenase. The cells were grown in a developed flat panel photobioreactor system with 3.0L culture volume either aerobically (air) or anaerobically (Ar or 80% N2/20% Ar) and illuminated with a mixture of red and white LED. Aerobic growth of the ΔhupW strain of Nostoc PCC 7120 at 44μmolar photons m(-2)s(-1) PAR gave the highest hydrogen production of 0.7mL H2 L(-1)h(-1), 0.53mmol H2 mg chlorophyll a(-1)h(-1), and a light energy conversion efficiency of 1.2%. Anaerobic growth using 100% argon showed a maximal hydrogen production of 1.7mLL(-1)h(-1), 0.85mmol per mg chlorophyll a(-1) h(-1), and a light energy conversion efficiency of 2.7%. Altering between argon/N2 (20/80) and 100% argon phases resulted in a maximal hydrogen production at hour 128 (100% argon phase) with 6.2mL H2L(-1)h(-1), 0.71mL H2 mg chlorophyll a(-1)h(-1), and a light energy efficiency conversion of 4.0%. The highest buildup of hydrogen gas observed was 6.89% H2 (100% argon phase) of the total photobioreactor system with a maximal production of 4.85mL H2 L(-1)h(-1). The present study clearly demonstrates the potential to use purpose design cyanobacteria in developed flat panel photobioreactor systems for the direct production of the solar fuel hydrogen. Further improvements in the strain used, environmental conditions employed, and growth, production and collection systems used, are needed before a sustainable and economical cyanobacterial based hydrogen production can be realized. Copyright © 2015 Elsevier B.V. All rights reserved.

Drug development: from concept to marketing!

PubMed

Tamimi, Nihad A M; Ellis, Peter

2009-01-01

Drug development is an expensive, long and high-risk business taking 10-15 years and is associated with a high attrition rate. It is driven by medical need, disease prevalence and the likelihood of success. Drug candidate selection is an iterative process between chemistry and biology, refining the molecular properties until a compound suitable for advancing to man is found. Typically, about one in a thousand synthesised compounds is ever selected for progression to the clinic. Prior to administration to humans, the pharmacology and biochemistry of the drug is established using an extensive range of in vitro and in vivo test procedures. It is also a regulatory requirement that the drug is administered to animals to assess its safety. Later-stage animal testing is also required to assess carcinogenicity and effects on the reproductive system. Clinical phases of drug development include phase I in healthy volunteers to assess primarily pharmacokinetics, safety and toleration, phase II in a cohort of patients with the target disease to establish efficacy and dose-response relationship and large-scale phase III studies to confirm safety and efficacy. Experience tells us that approximately only 1 in 10 drugs that start the clinical phase will make it to the market. Each drug must demonstrate safety and efficacy in the intended patient population and its benefits must outweigh its risks before it will be approved by the regulatory agencies. Strict regulatory standards govern the conduct of pre-clinical and clinical trials as well as the manufacturing of pharmaceutical products. The assessment of the new medicinal product's safety continues beyond the initial drug approval through post-marketing monitoring of adverse events. Copyright 2009 S. Karger AG, Basel.

IMPROVED TUBULARS FOR BETTER ECONOMICS IN DEEP GAS WELL DRILLING USING MICROWAVE TECHNOLOGY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dinesh Agrawal; Paul Gigl; Mahlon Dennis

2005-03-01

The main objective of the research program has been to improve the rate-of-penetration in deep hostile environments by improving the life cycle and performance of coiled-tubing, an important component of a deep well drilling system for oil and gas exploration, by utilizing the latest developments in the microwave materials technology. Originally, it was proposed to accomplish this by developing an efficient and economically viable continuous microwave process to sinter continuously formed/extruded steel powder for the manufacture of seamless coiled tubing and other tubular products. However, based on the results and faced with insurmountable difficulties in the extrusion and de-waxing processes,more » the approach of achieving the goals of the program has been slightly changed. In the continuation proposal an approach of microwave sintering combined with Cold Isostatic Press (CIP) and joining (by induction or microwave) is adopted. This process can be developed into a semi-continuous sintering process if the CIP can produce parts fast enough to match the microwave sintering rates. Originally, the entire program was spread over three phases with the following goals: Phase I: Demonstration of the feasibility concept of continuous microwave sintering process for tubular steel products. Phase II: Design, building and testing of a prototype microwave system which shall be combined with a continuous extruder for steel tubular objects. Phase III: Execution of the plan for commercialization of the technology by one of the industrial partners. However, since some of the goals of the phase I were not completed, an extension of nine months was granted and we continued extrusion experiments, designed and built semicontinuous microwave sintering unit.« less

Space Environments and Effects Concept: Transitioning Research to Operations and Applications

NASA Technical Reports Server (NTRS)

Edwards, David L.; Spann, James; Burns, Howard D.; Schumacher, Dan

2012-01-01

The National Aeronautics and Space Administration (NASA) is embarking on a course to expand human presence beyond Low Earth Orbit (LEO) while expanding its mission to explore the solar system. Destinations such as Near Earth Asteroids (NEA), Mars and its moons, and the outer planets are but a few of the mission targets. NASA has established numerous offices specializing in specific space environments disciplines that will serve to enable these missions. To complement these existing discipline offices, a concept focusing on the development of space environment and effects application is presented. This includes space climate, space weather, and natural and induced space environments. This space environment and effects application is composed of 4 topic areas; characterization and modeling, engineering effects, prediction and operation, and mitigation and avoidance. These topic areas are briefly described below. Characterization and modeling of space environments will primarily focus on utilization during Program mission concept, planning, and design phases. Engineering effects includes materials testing and flight experiments producing data to be used in mission planning and design phases. Prediction and operation pulls data from existing sources into decision-making tools and empirical data sets to be used during the operational phase of a mission. Mitigation and avoidance will develop techniques and strategies used in the design and operations phases of the mission. The goal of this space environment and effects application is to develop decision-making tools and engineering products to support the mission phases of mission concept through operations by focusing on transitioning research to operations. Products generated by this space environments and effects application are suitable for use in anomaly investigations. This paper will outline the four topic areas, describe the need, and discuss an organizational structure for this space environments and effects application.

Project H - A Complete Spaceport Hydrogen Solution

NASA Technical Reports Server (NTRS)

Notardonato, William

2011-01-01

This slide presentation reviews Project H, and its importance in the development of Kennedy Space Center (KSC) as a Spaceport capable of multiple launches. It is known that current KSC cryogenic technology results in only approximately 55 % of purchased hydrogen being used. The rest is lost at various points in the process: transfer from transporting vehicle to tank, storage tank boil off, and from the tank to the intended propulsion tanks. Project H's goals would be to have local hydrogen production and liquifaction capability, and to increase the efficiency of hydrogen operations to greater than 80 %. The project envisions two phases: Phase 1 will build a smaller scale demonstration system, and phase 2 will build a full scale spaceport system. This initial project has proposed ideas for local hydrogen production, gaseous distribution, integrated refrigeration and storage, and high efficiency transfer lines that merit further investigation.

Development of Simultaneous Beta-and-Coincidence-Gamma Imager for Plant Imaging Research

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tai, Yuan-Chuan

2016-09-30

The goal of this project is to develop a novel imaging system that can simultaneously acquire beta and coincidence gamma images of positron sources in thin objects such as leaves of plants. This hybrid imager can be used to measure carbon assimilation in plants quantitatively and in real-time after C-11 labeled carbon-dioxide is administered. A better understanding of carbon assimilation, particularly under the increasingly elevated atmospheric CO 2 level, is extremely critical for plant scientists who study food crop and biofuel production. Phase 1 of this project is focused on the technology development with 3 specific aims: (1) develop amore » hybrid detector that can detect beta and gamma rays simultaneously; (2) develop an imaging system that can differentiate these two types of radiation and acquire beta and coincidence gamma images in real-time; (3) develop techniques to quantify radiotracer distribution using beta and gamma images. Phase 2 of this project is to apply technologies developed in phase 1 to study plants using positron-emitting radionuclide such as 11C to study carbon assimilation in biofuel plants.« less

Automated Engineering Design (AED); An approach to automated documentation

NASA Technical Reports Server (NTRS)

Mcclure, C. W.

1970-01-01

The automated engineering design (AED) is reviewed, consisting of a high level systems programming language, a series of modular precoded subroutines, and a set of powerful software machine tools that effectively automate the production and design of new languages. AED is used primarily for development of problem and user-oriented languages. Software production phases are diagramed, and factors which inhibit effective documentation are evaluated.

Product Definition Data Interface (PDDI) Product Specification

DTIC Science & Technology

1991-07-01

syntax of the language gives a precise specification of the data without interpretation of it. M - Constituent Read Block. CSECT - Control Section, the...to conform to the PDDI Access Software’s internal data representation so that it may be further processed. JCL - Job Control Language - IBM language...software development and life cycle * phases. OUALITY CONTROL - The planned and systematic application of all actions (management/technical) necessary to

C3I and Modelling and Simulation (M&S) Interoperability

DTIC Science & Technology

2004-03-01

customised Open Source products. The technical implementation is based on the use of the eXtendend Markup Language (XML) and Python . XML is developed...to structure, store and send information. The language is focus on the description of data. Python is a portable, interpreted, object-oriented...programming language. A huge variety of usable Open Source Projects were issued by the Python Community. 3.1 Phase 1: Feasibility Studies Phase 1 was

Milk cow feed intake and milk production and distribution estimates for Phase 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beck, D.M.; Darwin, R.F.; Erickson, A.R.

1992-04-01

This report provides initial information on milk production and distribution in the Hanford Environmental Dose Reconstruction (HEDR) Project Phase I study area. The Phase I study area consists of eight countries in central Washington and two countries in northern Oregon. The primary objective of the HEDR Project is to develop estimates of the radiation doses populations could have received from Hanford operations. The objective of Phase I of the project was to determine the feasibility of reconstructing data, models, and development of preliminary dose estimates received by people living in the ten countries surrounding Hanford from 1944 to 1947. Onemore » of the most important contributors to radiation doses from Hanford during the period of interest was radioactive iodine. Consumption of milk from cows that ate vegetation contaminated with iodine is likely the dominant pathway of human exposure. To estimate the doses people could have received from this pathway, it is necessary to estimate the amount of milk that the people living in the Phase I area consumed, the source of the milk, and the type of feed that the milk cows ate. The objective of the milk model subtask is to identify the sources of milk supplied to residents of each community in the study area as well as the sources of feeds that were fed to the milk cows. In this report, we focus on Grade A cow's milk (fresh milk used for human consumption).« less

Genesis of a flexible turning center

NASA Astrophysics Data System (ADS)

Sanclemente, Paul; French, Robert D.

GE - Aircraft Engines has designed, built, and is operating a flexible turning center for jet engine hardware. Although the plant is in the forefront of manufacturing technology development, it was intended from the start to be a production facility. So while there was much to learn from being involved in all phases of the project, meeting production schedules was, and is, key to its success. This paper reviews the early history of the project and ends with a view of its recent production status.

Effect of biochar addition on hydrogen and methane production in two-phase anaerobic digestion of aqueous carbohydrates food waste.

PubMed

Sunyoto, Nimas M S; Zhu, Mingming; Zhang, Zhezi; Zhang, Dongke

2016-11-01

Effect of biochar addition on hydrogen and methane production in two-phase anaerobic digestion of aqueous carbohydrates was studied using bench-scale bioreactors. The cultures with biochar additions were placed in 100ml reactors and incubated at 35°C and pH 5 for hydrogen production. The residual cultures were then used for methane production, incubated at 35°C and pH 7. Daily yields of hydrogen and methane and weekly yield of volatile fatty acids (VFA) were measured. The hydrogen and methane production potentials, rate and lag phases of the two phases were analysed using the Gompertz model. The results showed that biochar addition increased the maximum production rates of hydrogen by 32.5% and methane 41.6%, improved hydrogen yield by 31.0% and methane 10.0%, and shortened the lag phases in the two phases by 36.0% and 41.0%, respectively. Biochar addition also enhanced VFA generation during hydrogen production and VFA degradation in methane production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Budgetary and Programmatic Fluctuations during the System Development and Demonstration Phase: A Case Study of the Marine Corps H-1 Upgrade Program

DTIC Science & Technology

2007-12-01

impact of economic change might include a closing factory, market manipulation, the signing of international trade 17 treaties, or the global...Refinement System Intergration System Demonstration Concept Decision BA C LRIP Full-Rate Production & Deployment System Development and Demonstration...BLOCK III Concept Exploration Component Advanced Development Concept and Technology Development System Intergration System Demonstration Decision Review

Investigations about the quantitative changes of carbon dioxide production in humans. Report 2: Carbon dioxide production during fever and its relationship with heat production

NASA Technical Reports Server (NTRS)

Liebermeister, C.

1978-01-01

Investigations are cited and explained for carbon dioxide production during fever and its relationship with heat production. The general topics of discussion are: (1) carbon dioxide production for alternating fever attacks; (2) heat balance during the perspiration phase; (3) heat balance during the chill phase; (4) the theory of fever; and (5) chill phase for other fever attacks.

Commercial-scale demonstration of the Liquid Phase Methanol process. Technical progress report number 8, April 1--June 30, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-12-31

The project involves the construction of an 80,000 gallon per day (260 tons per day (TPD)) methanol unit utilizing coal-derived synthesis gas from Eastman`s integrated coal gasification facility. The new equipment consists of synthesis gas feed preparation and compression facilities, the liquid phase reactor and auxiliaries, product distillation facilities, and utilities. The technology to be demonstrated is the product of a cooperative development effort by Air Products and DOE in a program that started in 1981. Developed to enhance electric power generation using integrated gasification combined cycle (IGCC) technology, the LPMEOH{trademark} process is ideally suited for directly processing gases producedmore » by modern-day coal gasifiers. Originally tested at a small (10 TPD), DOE-owned experimental unit in LaPorte, Texas, the technology provides several improvements essential for the economic coproduction of methanol and electricity directly from gasified coal. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The slurry dissipates the heat of the chemical reaction away from the catalyst surface, protecting the catalyst and allowing the methanol synthesis reaction to proceed at higher rates. At the Eastman complex, the technology is being integrated with existing coal-gasifiers. A carefully developed test plan will allow operations at Eastman to simulate electricity demand load-following in coal-based IGCC facilities. The operations will also demonstrate the enhanced stability and heat dissipation of the conversion process, its reliable on/off operation, and its ability to produce methanol as a clean liquid fuel without additional upgrading.« less

Penicillinase Studies on L-Phase Variants, G-Phase Variants, and Reverted Strains of Staphylococcus aureus

PubMed Central

Simon, Harold J.; Yin, Elaine Jong

1970-01-01

L-phase variants and small colony (G-phase) variants derived from penicillinase-producing Staphylococcus aureus strains were tested for penicillinase (beta lactamase) production. A refined variation of the modified Gots test for penicillinase was used to demonstrate penicillinase synthesis. Penicillinase synthesis was reduced in L-phase variants and G-phase variants when compared to parental strains. After reversion of variants to vegetative stages had been induced, revertants were tested for production of penicillinase, coagulase, and alpha hemolysin, mannitol fermentation, and pigment production, and comparisons were made between parent and reverted vegetative forms. All revertants of G-phase variants retained penicillinase activity. Most revertants of L-phase variants showed reduction or loss of penicillinase activity. Retention of coagulase activity, alpha hemolysin production, mannitol fermentation, pigmentation, and phage type varied among revertants. Images PMID:16557890

Minimization of Defective Products in The Department of Press Bridge & Rib Through Six Sigma DMAIC Phases

NASA Astrophysics Data System (ADS)

Rochman, YA; Agustin, A.

2017-06-01

This study proposes the DMAIC Six Sigma approach of Define, Measure, Analyze, Improve/Implement and Control (DMAIC) to minimizing the number of defective products in the bridge & rib department. There are 5 types of defects were the most dominant are broken rib, broken sound board, strained rib, rib sliding and sound board minori. The imperative objective is to improve the quality through the DMAIC phases. In the define phase, the critical to quality (CTQ) parameters was identified minimization of product defects through the pareto chart and FMEA. In this phase, to identify waste based on the current value stream mapping. In the measure phase, the specified control limits product used to maintain the variations of the product, the calculation of the value of DPMO (Defect Per Million Opportunities) and the calculation of the value of sigma level. In analyze phase, determine the type of defect of the most dominant and identify the causes of defective products. In the improve phase, the existing design was modified through various alternative solutions by conducting brainstorming sessions. In this phase, the solution was identified based on the results of FMEA. Improvements were made to the seven priority causes of disability based on the highest RPN value. In the control phase, focusing on improvements to be made. Proposed improvements include making and define standard operating procedures, improving the quality and eliminate waste defective products.

Site Development, Operations, and Closure Plan Topical Report 5 An Assessment of Geologic Carbon Sequestration Options in the Illinois Basin. Phase III

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finley, Robert; Payne, William; Kirksey, Jim

2015-06-01

The Midwest Geological Sequestration Consortium (MGSC) has partnered with Archer Daniels Midland Company (ADM) and Schlumberger Carbon Services to conduct a large-volume, saline reservoir storage project at ADM’s agricultural products processing complex in Decatur, Illinois. The Development Phase project, named the Illinois Basin Decatur Project (IBDP) involves the injection of 1 million tonnes of carbon dioxide (CO 2) into a deep saline formation of the Illinois Basin over a three-year period. This report focuses on objectives, execution, and lessons learned/unanticipated results from the site development (relating specifically to surface equipment), operations, and the site closure plan.

Advanced Natural Gas Reciprocating Engine(s)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pike, Edward

The objective of the Cummins ARES program, in partnership with the US Department of Energy (DOE), is to develop advanced natural gas engine technologies that increase engine system efficiency at lower emissions levels while attaining lower cost of ownership. The goals of the project are to demonstrate engine system achieving 50% Brake Thermal Efficiency (BTE) in three phases, 44%, 47% and 50% (starting baseline efficiency at 36% BTE) and 0.1 g/bhp-hr NOx system out emissions (starting baseline NOx emissions at 2 – 4 g/bhp-hr NOx). Primary path towards above goals include high Brake Mean Effective Pressure (BMEP), improved closed cyclemore » efficiency, increased air handling efficiency and optimized engine subsystems. Cummins has successfully demonstrated each of the phases of this program. All targets have been achieved through application of a combined set of advanced base engine technologies and Waste Heat Recovery from Charge Air and Exhaust streams, optimized and validated on the demonstration engine and other large engines. The following architectures were selected for each Phase: Phase 1: Lean Burn Spark Ignited (SI) Key Technologies: High Efficiency Turbocharging, Higher Efficiency Combustion System. In production on the 60/91L engines. Over 500MW of ARES Phase 1 technology has been sold. Phase 2: Lean Burn Technology with Exhaust Waste Heat Recovery (WHR) System Key Technologies: Advanced Ignition System, Combustion Improvement, Integrated Waste Heat Recovery System. Base engine technologies intended for production within 2 to 3 years Phase 3: Lean Burn Technology with Exhaust and Charge Air Waste Heat Recovery System Key Technologies: Lower Friction, New Cylinder Head Designs, Improved Integrated Waste Heat Recovery System. Intended for production within 5 to 6 years Cummins is committed to the launch of next generation of large advanced NG engines based on ARES technology to be commercialized worldwide.« less

Managing Zirconium Chemistry and Phase Compatibility in Combined Process Separations for Minor Actinide Partitioning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wall, Nathalie; Nash, Ken; Martin, Leigh

In response to the NEUP Program Supporting Fuel Cycle R&D Separations and Waste Forms call DEFOA- 0000799, this report describes the results of an R&D project focusing on streamlining separation processes for advanced fuel cycles. An example of such a process relevant to the U.S. DOE FCR&D program would be one combining the functions of the TRUEX process for partitioning of lanthanides and minor actinides from PUREX(UREX) raffinates with that of the TALSPEAK process for separating transplutonium actinides from fission product lanthanides. A fully-developed PUREX(UREX)/TRUEX/TALSPEAK suite would generate actinides as product(s) for reuse (or transmutation) and fission products as waste.more » As standalone, consecutive unit-operations, TRUEX and TALSPEAK employ different extractant solutions (solvating (CMPO, octyl(phenyl)-N,Ndiisobutylcarbamoylmethylphosphine oxide) vs. cation exchanging (HDEHP, di-2(ethyl)hexylphosphoric acid) extractants), and distinct aqueous phases (2-4 M HNO 3 vs. concentrated pH 3.5 carboxylic acid buffers containing actinide selective chelating agents). The separate processes may also operate with different phase transfer kinetic constraints. Experience teaches (and it has been demonstrated at the lab scale) that, with proper control, multiple process separation systems can operate successfully. However, it is also recognized that considerable economies of scale could be achieved if multiple operations could be merged into a single process based on a combined extractant solvent. The task of accountability of nuclear materials through the process(es) also becomes more robust with fewer steps, providing that the processes can be accurately modeled. Work is underway in the U.S. and Europe on developing several new options for combined processes (TRUSPEAK, ALSEP, SANEX, GANEX, ExAm are examples). There are unique challenges associated with the operation of such processes, some relating to organic phase chemistry, others arising from the variable composition of the aqueous medium. This project targets in particular two problematic issues in designing combined process systems: managing the chemistry of challenging aqueous species (like Zr 4+) and optimizing the composition and properties of combined extractant organic phases.« less

Future utilization of space: Silverton Conference on material science and phase transformations in zero-gravity, summary of proceeding

NASA Technical Reports Server (NTRS)

Eisner, M. (Editor)

1975-01-01

The importance of zero gravity environment in the development and production of new and improved materials is considered along with the gravitational effects on phase changes or critical behavior in a variety of materials. Specific experiments discussed include: fine scale phase separation in zero gravity; glass formation in zero gravity; effects of gravitational perturbations on determination of critical exponents; and light scattering from long wave fluctuations in liquids in zero gravity. It is concluded that the space shuttle/spacelab system is applicable to various fields of interest.

Basic Requirements for Systems Software Research and Development

NASA Technical Reports Server (NTRS)

Kuszmaul, Chris; Nitzberg, Bill

1996-01-01

Our success over the past ten years evaluating and developing advanced computing technologies has been due to a simple research and development (R/D) model. Our model has three phases: (a) evaluating the state-of-the-art, (b) identifying problems and creating innovations, and (c) developing solutions, improving the state- of-the-art. This cycle has four basic requirements: a large production testbed with real users, a diverse collection of state-of-the-art hardware, facilities for evalua- tion of emerging technologies and development of innovations, and control over system management on these testbeds. Future research will be irrelevant and future products will not work if any of these requirements is eliminated. In order to retain our effectiveness, the numerical aerospace simulator (NAS) must replace out-of-date production testbeds in as timely a fashion as possible, and cannot afford to ignore innovative designs such as new distributed shared memory machines, clustered commodity-based computers, and multi-threaded architectures.

Dissociation of Calcium Transients and Force Development following a Change in Stimulation Frequency in Isolated Rabbit Myocardium.

PubMed

Haizlip, Kaylan M; Milani-Nejad, Nima; Brunello, Lucia; Varian, Kenneth D; Slabaugh, Jessica L; Walton, Shane D; Gyorke, Sandor; Davis, Jonathan P; Biesiadecki, Brandon J; Janssen, Paul M L

2015-01-01

As the heart transitions from one exercise intensity to another, changes in cardiac output occur, which are modulated by alterations in force development and calcium handling. Although the steady-state force-calcium relationship at various heart rates is well investigated, regulation of these processes during transitions in heart rate is poorly understood. In isolated right ventricular muscle preparations from the rabbit, we investigated the beat-to-beat alterations in force and calcium during the transition from one stimulation frequency to another, using contractile assessments and confocal microscopy. We show that a change in steady-state conditions occurs in multiple phases: a rapid phase, which is characterized by a fast change in force production mirrored by a change in calcium transient amplitude, and a slow phase, which follows the rapid phase and occurs as the muscle proceeds to stabilize at the new frequency. This second/late phase is characterized by a quantitative dissociation between the calcium transient amplitude and developed force. Twitch timing kinetics, such as time to peak tension and 50% relaxation rate, reached steady-state well before force development and calcium transient amplitude. The dynamic relationship between force and calcium upon a switch in stimulation frequency unveils the dynamic involvement of myofilament-based properties in frequency-dependent activation.

An attributional life cycle assessment for an Italian residential multifamily building.

PubMed

Vitale, Pierluca; Arena, Umberto

2017-09-06

The study describes an attributional life cycle assessment carried out according to the ISO standards and focused on an Italian multifamily residential building. The aim was developing an exhaustive and reliable inventory of high-quality primary data, comparing the environmental impacts along the three stages of the building life cycle. The pre-use phase takes into account the production of all the construction materials, transportation, and on-site assembling. The use phase quantifies the resource consumptions for 50 years of the building utilization and ordinary maintenance. The end-of-life phase includes the building demolition and the management of generated wastes. The results quantify how the design criteria affect the environmental performances of the residential building along its life cycle. The role of the pre-use phase appears remarkable for global warming potential (GWP), due to the huge impacts of steel and concrete production processes. The use phase gives the largest contributions, which reach 77% and 84% of the total, for the categories of global warming and non-renewable energy. The end-of-life phase provides limited avoided impacts. A comparative analysis quantifies the improvements achievable with an alternative type of partitions and external walls. Acronyms: AC: air conditioning; C&DW: construction and demolition waste; CFL: compact fluorescent lamp; DHW: domestic hot water; EC: European Commission; EU: European Union; GDP: gross domestic product; GHG: greenhouse gases; GWP: global warming potential; LCA: life cycle assessment; LCI: life cycle inventory; LCIA: life cycle impact assessment; MFA: material flow analysis; NREP: non-renewable energy potential; RINP: respiratory inorganics potential; WFD: Waste Framework Directive.

Function of the Pyruvate Oxidase-Lactate Oxidase Cascade in Interspecies Competition between Streptococcus oligofermentans and Streptococcus mutans

PubMed Central

Liu, Lei

2012-01-01

Complex interspecies interactions occur constantly between oral commensals and the opportunistic pathogen Streptococcus mutans in dental plaque. Previously, we showed that oral commensal Streptococcus oligofermentans possesses multiple enzymes for H2O2 production, especially lactate oxidase (Lox), allowing it to out-compete S. mutans. In this study, through extensive biochemical and genetic studies, we identified a pyruvate oxidase (pox) gene in S. oligofermentans. A pox deletion mutant completely lost Pox activity, while ectopically expressed pox restored activity. Pox was determined to produce most of the H2O2 in the earlier growth phase and log phase, while Lox mainly contributed to H2O2 production in stationary phase. Both pox and lox were expressed throughout the growth phase, while expression of the lox gene increased by about 2.5-fold when cells entered stationary phase. Since lactate accumulation occurred to a large degree in stationary phase, the differential Pox- and Lox-generated H2O2 can be attributed to differential gene expression and substrate availability. Interestingly, inactivation of pox causes a dramatic reduction in H2O2 production from lactate, suggesting a synergistic action of the two oxidases in converting lactate into H2O2. In an in vitro two-species biofilm experiment, the pox mutant of S. oligofermentans failed to inhibit S. mutans even though lox was active. In summary, S. oligofermentans develops a Pox-Lox synergy strategy to maximize its H2O2 formation so as to win the interspecies competition. PMID:22287002

Increasing productivity through Total Reuse Management (TRM)

NASA Technical Reports Server (NTRS)

Schuler, M. P.

1991-01-01

Total Reuse Management (TRM) is a new concept currently being promoted by the NASA Langley Software Engineering and Ada Lab (SEAL). It uses concepts similar to those promoted in Total Quality Management (TQM). Both technical and management personnel are continually encouraged to think in terms of reuse. Reuse is not something that is aimed for after a product is completed, but rather it is built into the product from inception through development. Lowering software development costs, reducing risk, and increasing code reliability are the more prominent goals of TRM. Procedures and methods used to adopt and apply TRM are described. Reuse is frequently thought of as only being applicable to code. However, reuse can apply to all products and all phases of the software life cycle. These products include management and quality assurance plans, designs, and testing procedures. Specific examples of successfully reused products are given and future goals are discussed.

Space station WP-04 power system. Volume 2: Study results

NASA Technical Reports Server (NTRS)

Hallinan, G. J.

1987-01-01

Results of the phase B study contract for the definition of the space station Electric Power System (EPS) are presented in detail along with backup information and supporting data. Systems analysis and trades, preliminary design, advanced development, customer accommodations, operations planning, product assurance, and design and development phase planning are addressed. The station design is a hybrid approach which provides user power of 25 kWe from the photovoltaic subsystem and 50 kWe from the solar dynamic subsystem. The electric power is distributed to users as a utility service; single phase at a frequency of 20 kHz and voltage of 440VAC. The solar array NiH2 batteries of the photovoltaic subsystem are based on commonality to those used on the co-orbiting and solar platforms.

Reducing energy consumption and carbon emissions of magnesia refractory products: A life-cycle perspective

DOE PAGES

An, Jing; Li, Yingnan; Middleton, Richard S.

2018-02-20

China is the largest producer of magnesia refractory materials and products in the world, resulting in significant energy consumption and carbon emissions. This paper analyzes measures to reduce both the energy consumption and carbon emissions in the production phase and use phase, providing a theoretical basis for a sustainable magnesia refractory industry. Results show that the total carbon emissions of carbon-containing magnesia bricks produced with fused magnesia are much higher than those of other products, and the total carbon emissions of both general magnesia brick and magnesia-carbon spray are lower than those of other products. Carbon emissions of magnesia productsmore » are mainly concentrated in the production process of magnesia. Manufacturers should select materials with lower environmental impacts and emphasize saving energy and reducing carbon emissions in the magnesia production process. Through scenario analysis we found that CO 2 capture is an effective measure to reduce carbon emissions compared with just improving energy consumption. However, a robust CO 2 market does not currently exist. Policy makers should plan on integrating CO 2 capture in the magnesia industry into a regional CO 2 capture and storage development planning in the long term. In particular, magnesia production is concentrated in a single geographical area which would and thus could take advantage of significant scale effects. Finally, in the use phase, extending the service lifetime reduces carbon emissions over the product lifetime, thus users should attempt to extend the service lifetime of a furnace as a whole. However, results show that it is not advisable to add a large number of repair refractories to extend the lifetime of existing furnaces.« less

Economic analysis of pilot-scale production of B-phycoerythrin.

PubMed

Torres-Acosta, Mario A; Ruiz-Ruiz, Federico; Aguilar-Yáñez, José M; Benavides, Jorge; Rito-Palomares, Marco

2016-11-01

β-Phycoerythrin is a color protein with several applications, from food coloring to molecular labeling. Depending on the application, different purity is required, affecting production cost and price. Different production and purification strategies for B-phycoerythrin have been developed, the most studied are based on the production using Porphyridium cruentum and purified using chromatographic techniques or aqueous two-phase systems. The use of the latter can result in a less expensive and intensive recovery of the protein, but there is lack of a proper economic analysis to study the effect of using aqueous two-phase systems in a scaled-up process. This study analyzed the production of B-Phycoerythrin using real data obtained during the scale-up of a bioprocess using specialized software (BioSolve, Biopharm Services, UK). First, a sensitivity analysis was performed to identify critical parameters for the production cost, then a Monte Carlo analysis to emulate real processes by adding uncertainty to the identified parameters. Next, the bioprocess was analyzed to determine its financial attractiveness and possible optimization strategies were tested and discussed. Results show that aqueous two-phase systems retain their advantages of low cost and intensive recovery (54.56%); the costs of production per gram calculated (before titer optimization: US$15,709 and after optimization: US$2,374) allowed to obtain profit (in the range of US$millions in a 10-year period) for a potential company taking this production method by comparing the production cost against commercial prices. The bioprocess analyzed is a promising and profitable method for the generation of a highly purified B-phycoerythrin. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:1472-1479, 2016. © 2016 American Institute of Chemical Engineers.

Reducing energy consumption and carbon emissions of magnesia refractory products: A life-cycle perspective

DOE Office of Scientific and Technical Information (OSTI.GOV)

An, Jing; Li, Yingnan; Middleton, Richard S.

China is the largest producer of magnesia refractory materials and products in the world, resulting in significant energy consumption and carbon emissions. This paper analyzes measures to reduce both the energy consumption and carbon emissions in the production phase and use phase, providing a theoretical basis for a sustainable magnesia refractory industry. Results show that the total carbon emissions of carbon-containing magnesia bricks produced with fused magnesia are much higher than those of other products, and the total carbon emissions of both general magnesia brick and magnesia-carbon spray are lower than those of other products. Carbon emissions of magnesia productsmore » are mainly concentrated in the production process of magnesia. Manufacturers should select materials with lower environmental impacts and emphasize saving energy and reducing carbon emissions in the magnesia production process. Through scenario analysis we found that CO 2 capture is an effective measure to reduce carbon emissions compared with just improving energy consumption. However, a robust CO 2 market does not currently exist. Policy makers should plan on integrating CO 2 capture in the magnesia industry into a regional CO 2 capture and storage development planning in the long term. In particular, magnesia production is concentrated in a single geographical area which would and thus could take advantage of significant scale effects. Finally, in the use phase, extending the service lifetime reduces carbon emissions over the product lifetime, thus users should attempt to extend the service lifetime of a furnace as a whole. However, results show that it is not advisable to add a large number of repair refractories to extend the lifetime of existing furnaces.« less

Microfluidic and nanofluidic phase behaviour characterization for industrial CO2, oil and gas.

PubMed

Bao, Bo; Riordon, Jason; Mostowfi, Farshid; Sinton, David

2017-08-08

Microfluidic systems that leverage unique micro-scale phenomena have been developed to provide rapid, accurate and robust analysis, predominantly for biomedical applications. These attributes, in addition to the ability to access high temperatures and pressures, have motivated recent expanded applications in phase measurements relevant to industrial CO 2 , oil and gas applications. We here present a comprehensive review of this exciting new field, separating microfluidic and nanofluidic approaches. Microfluidics is practical, and provides similar phase properties analysis to established bulk methods with advantages in speed, control and sample size. Nanofluidic phase behaviour can deviate from bulk measurements, which is of particular relevance to emerging unconventional oil and gas production from nanoporous shale. In short, microfluidics offers a practical, compelling replacement of current bulk phase measurement systems, whereas nanofluidics is not practical, but uniquely provides insight into phase change phenomena at nanoscales. Challenges, trends and opportunities for phase measurements at both scales are highlighted.

Advancing molecular-guided surgery through probe development and testing in a moderate cost evaluation pipeline

NASA Astrophysics Data System (ADS)

Pogue, Brian W.; Paulsen, Keith D.; Hull, Sally M.; Samkoe, Kimberley S.; Gunn, Jason; Hoopes, Jack; Roberts, David W.; Strong, Theresa V.; Draney, Daniel; Feldwisch, Joachim

2015-03-01

Molecular guided oncology surgery has the potential to transform the way decisions about resection are done, and can be critically important in areas such as neurosurgery where the margins of tumor relative to critical normal tissues are not readily apparent from visual or palpable guidance. Yet there are major financial barriers to advancing agents into clinical trials with commercial backing. We observe that development of these agents in the standard biological therapeutic paradigm is not viable, due to the high up front financial investment needed and the limitations in the revenue models of contrast agents for imaging. The hypothesized solution to this problem is to develop small molecular biologicals tagged with an established fluorescent reporter, through the chemical agent approval pathway, targeting a phase 0 trials initially, such that the initial startup phase can be completely funded by a single NIH grant. In this way, fast trials can be completed to de-risk the development pipeline, and advance the idea of fluorescence-guided surgery (FGS) reporters into human testing. As with biological therapies the potential successes of each agent are still moderate, but this process will allow the field to advance in a more stable and productive manner, rather than relying upon isolated molecules developed at high cost and risk. The pathway proposed and tested here uses peptide synthesis of an epidermal growth factor receptor (EGFR)-binding Affibody molecules, uniquely conjugated to IRDye 800CW, developed and tested in academic and industrial laboratories with well-established records for GMP production, fill and finish, toxicity testing, and early phase clinical trials with image guidance.

A Low Temperature, Reverse Brayton Cryocooler

NASA Technical Reports Server (NTRS)

Swift, Walter L.

2001-01-01

This status report covers the fifty-second month of a project to develop a low temperature, reverse-Brayton cryocooler using turbomachines. This program consists of a Basic Phase and four Option Phases. Each of the Phases is directed to a particular load/temperature combination. The technology and fundamental design features of the components used in these systems are related but differ somewhat in size, speed, and some details in physical geometry. Each of the Phases can be carried out independently of the others, except that all of the Phases rely on the technology developed and demonstrated during the Basic Phase. The Basic Phase includes the demonstration of a critical component and the production of a prototype model cryocooler. The critical technology demonstration will be the test of a small turboalternator over a range of conditions at temperatures down to 6 K. These tests will provide design verification data useful for the further design of the other coolers. The prototype model cooler will be designed to provide at least 5 mW of cooling at 6 K. The heat rejection temperature for this requirement is 220 K or greater. The input power to the system at these conditions is to be less than 60 W.

Solar-light photocatalytic disinfection using crystalline/amorphous low energy bandgap reduced TiO2

PubMed Central

Kim, Youngmin; Hwang, Hee Min; Wang, Luyang; Kim, Ikjoon; Yoon, Yeoheung; Lee, Hyoyoung

2016-01-01

A generation of reactive oxygen species (ROS) from TiO2 under solar light has been long sought since the ROS can disinfect organic pollutants. We found that newly developed crystalline/amorphous reduced TiO2 (rTiO2) that has low energy bandgap can effectively generate ROS under solar light and successfully remove a bloom of algae. The preparation of rTiO2 is a one-pot and mass productive solution-process reduction using lithium-ethylene diamine (Li-EDA) at room temperature. Interestingly only the rutile phase of TiO2 crystal was reduced, while the anatase phase even in case of both anatase/rutile phased TiO2 was not reduced. Only reduced TiO2 materials can generate ROS under solar light, which was confirmed by electron spin resonance. Among the three different types of Li-EDA treated TiO2 (anatase, rutile and both phased TiO2), the both phased rTiO2 showed the best performance to produce ROS. The generated ROS effectively removed the common green algae Chlamydomonas. This is the first report on algae degradation under solar light, proving the feasibility of commercially available products for disinfection. PMID:27121120

Computer-Based Tools for Evaluating Graphical User Interfaces

NASA Technical Reports Server (NTRS)

Moore, Loretta A.

1997-01-01

The user interface is the component of a software system that connects two very complex system: humans and computers. Each of these two systems impose certain requirements on the final product. The user is the judge of the usability and utility of the system; the computer software and hardware are the tools with which the interface is constructed. Mistakes are sometimes made in designing and developing user interfaces because the designers and developers have limited knowledge about human performance (e.g., problem solving, decision making, planning, and reasoning). Even those trained in user interface design make mistakes because they are unable to address all of the known requirements and constraints on design. Evaluation of the user inter-face is therefore a critical phase of the user interface development process. Evaluation should not be considered the final phase of design; but it should be part of an iterative design cycle with the output of evaluation being feed back into design. The goal of this research was to develop a set of computer-based tools for objectively evaluating graphical user interfaces. The research was organized into three phases. The first phase resulted in the development of an embedded evaluation tool which evaluates the usability of a graphical user interface based on a user's performance. An expert system to assist in the design and evaluation of user interfaces based upon rules and guidelines was developed during the second phase. During the final phase of the research an automatic layout tool to be used in the initial design of graphical inter- faces was developed. The research was coordinated with NASA Marshall Space Flight Center's Mission Operations Laboratory's efforts in developing onboard payload display specifications for the Space Station.

Replacement of Ablators with Phase-Change Material for Thermal Protection of STS Elements

NASA Technical Reports Server (NTRS)

Kaul, Raj K.; Stuckey, Irvin; Munafo, Paul M. (Technical Monitor)

2002-01-01

As part of the research and development program to develop new Thermal Protection System (TPS) materials for aerospace applications at NASA's Marshall Space Flight Center (MSFC), an experimental study was conducted on a new concept for a non-ablative TPS material. Potential loss of TPS material and ablation by-products from the External Tank (ET) or Solid Rocket Booster (SRB) during Shuttle flight with the related Orbiter tile damage necessitates development of a non-ablative thermal protection system. The new Thermal Management Coating (TMC) consists of phase-change material encapsulated in micro spheres and a two-part resin system to adhere the coating to the structure material. The TMC uses a phase-change material to dissipate the heat produced during supersonic flight rather than an ablative material. This new material absorbs energy as it goes through a phase change during the heating portion of the flight profile and then the energy is slowly released as the phase-change material cools and returns to its solid state inside the micro spheres. The coating was subjected to different test conditions simulating design flight environments at the NASA/MSFC Improved Hot Gas Facility (IHGF) to study its performance.

In situ production of titanium dioxide nanoparticles in molten salt phase for thermal energy storage and heat-transfer fluid applications.

PubMed

Lasfargues, Mathieu; Bell, Andrew; Ding, Yulong

In this study, TiO 2 nanoparticles (average particle size 16 nm) were successfully produced in molten salt phase and were showed to significantly enhance the specific heat capacity of a binary eutectic mixture of sodium and potassium nitrate (60/40) by 5.4 % at 390 °C and 7.5 % at 445 °C for 3.0 wt% of precursors used. The objective of this research was to develop a cost-effective alternate method of production which is potentially scalable, as current techniques utilized are not economically viable for large quantities. Enhancing the specific heat capacity of molten salt would promote more competitive pricing for electricity production by concentrating solar power plant. Here, a simple precursor (TiOSO 4 ) was added to a binary eutectic mixture of potassium and sodium nitrate, heated to 450 °C, and cooled to witness the production of nanoparticles.

Agile science: creating useful products for behavior change in the real world.

PubMed

Hekler, Eric B; Klasnja, Predrag; Riley, William T; Buman, Matthew P; Huberty, Jennifer; Rivera, Daniel E; Martin, Cesar A

2016-06-01

Evidence-based practice is important for behavioral interventions but there is debate on how best to support real-world behavior change. The purpose of this paper is to define products and a preliminary process for efficiently and adaptively creating and curating a knowledge base for behavior change for real-world implementation. We look to evidence-based practice suggestions and draw parallels to software development. We argue to target three products: (1) the smallest, meaningful, self-contained, and repurposable behavior change modules of an intervention; (2) "computational models" that define the interaction between modules, individuals, and context; and (3) "personalization" algorithms, which are decision rules for intervention adaptation. The "agile science" process includes a generation phase whereby contender operational definitions and constructs of the three products are created and assessed for feasibility and an evaluation phase, whereby effect size estimates/casual inferences are created. The process emphasizes early-and-often sharing. If correct, agile science could enable a more robust knowledge base for behavior change.

Titanium Aluminide Casting Technology Development

NASA Astrophysics Data System (ADS)

Bünck, Matthias; Stoyanov, Todor; Schievenbusch, Jan; Michels, Heiner; Gußfeld, Alexander

2017-12-01

Titanium aluminide alloys have been successfully introduced into civil aircraft engine technology in recent years, and a significant order volume increase is expected in the near future. Due to its beneficial buy-to-fly ratio, investment casting bears the highest potential for cost reduction of all competing production technologies for TiAl-LPTB. However, highest mechanical properties can be achieved by TiAl forging. In view of this, Access e.V. has developed technologies for the production of TiAl investment cast parts and TiAl die cast billets for forging purposes. While these parts meet the highest requirements, establishing series production and further optimizing resource and economic efficiency are present challenges. In order to meet these goals, Access has recently been certified according to aircraft standards, aiming at qualifying parts for production on technology readiness level 6. The present work gives an overview of the phases of development and certification.

The Skype-Buddy Model in an Online Environment: Patterns and Perceptions of Language Teachers in a Professional Development Program

ERIC Educational Resources Information Center

Macharaschwili, Carmen E.

2013-01-01

Patterns and perceptions of language teachers in a professional development program were examined through various forms of classroom discourse & multimodal products. Research questions include: What kinds of learning patterns emerge with the use of Skype in an online environment? What phases of cognitive engagement are evident in Skype…

The development of interactive multimedia based on auditory, intellectually, repetition in repetition algorithm learning to increase learning outcome

NASA Astrophysics Data System (ADS)

Munir; Sutarno, H.; Aisyah, N. S.

2018-05-01

This research aims to find out how the development of interactive multimedia based on auditory, intellectually, and repetition can improve student learning outcomes. This interactive multimedia is developed through 5 stages. Analysis stages include the study of literature, questionnaire, interviews and observations. The design phase is done by the database design, flowchart, storyboards and repetition algorithm material while the development phase is done by the creation of web-based framework. Presentation material is adapted to the model of learning such as auditory, intellectually, repetition. Auditory points are obtained by recording the narrative material that presented by a variety of intellectual points. Multimedia as a product is validated by material and media experts. Implementation phase conducted on grade XI-TKJ2 SMKN 1 Garut. Based on index’s gain, an increasing of student learning outcomes in this study is 0.46 which is fair due to interest of student in using interactive multimedia. While the multimedia assessment earned 84.36% which is categorized as very well.

Identifying product order with restricted Boltzmann machines

NASA Astrophysics Data System (ADS)

Rao, Wen-Jia; Li, Zhenyu; Zhu, Qiong; Luo, Mingxing; Wan, Xin

2018-03-01

Unsupervised machine learning via a restricted Boltzmann machine is a useful tool in distinguishing an ordered phase from a disordered phase. Here we study its application on the two-dimensional Ashkin-Teller model, which features a partially ordered product phase. We train the neural network with spin configuration data generated by Monte Carlo simulations and show that distinct features of the product phase can be learned from nonergodic samples resulting from symmetry breaking. Careful analysis of the weight matrices inspires us to define a nontrivial machine-learning motivated quantity of the product form, which resembles the conventional product order parameter.

Software reuse issues affecting AdaNET

NASA Technical Reports Server (NTRS)

Mcbride, John G.

1989-01-01

The AdaNet program is reviewing its long-term goals and strategies. A significant concern is whether current AdaNet plans adequately address the major strategic issues of software reuse technology. The major reuse issues of providing AdaNet services that should be addressed as part of future AdaNet development are identified and reviewed. Before significant development proceeds, a plan should be developed to resolve the aforementioned issues. This plan should also specify a detailed approach to develop AdaNet. A three phased strategy is recommended. The first phase would consist of requirements analysis and produce an AdaNet system requirements specification. It would consider the requirements of AdaNet in terms of mission needs, commercial realities, and administrative policies affecting development, and the experience of AdaNet and other projects promoting the transfer software engineering technology. Specifically, requirements analysis would be performed to better understand the requirements for AdaNet functions. The second phase would provide a detailed design of the system. The AdaNet should be designed with emphasis on the use of existing technology readily available to the AdaNet program. A number of reuse products are available upon which AdaNet could be based. This would significantly reduce the risk and cost of providing an AdaNet system. Once a design was developed, implementation would proceed in the third phase.

Updates on Managing Type 2 Diabetes Mellitus with Natural Products: Towards Antidiabetic Drug Development.

PubMed

Alam, Fahmida; Islam, Md Asiful; Kamal, M A; Gan, Siew Hua

2016-08-13

Over the years, natural products have shown success as antidiabetics in vitro, in vivo and in clinical trials. Because natural product-derived drugs are more affordable and effective with fewer side-effects compared to conventional therapies, pharmaceutical research is increasingly leaning towards the discovery of new antidiabetic drugs from natural products targeting pathways or components associated with type 2 diabetes mellitus (T2DM) pathophysiology. However, the drug discovery process is very lengthy and costly with significant challenges. Therefore, various techniques are currently being developed for the preclinical research phase of drug discovery with the aim of drug development with less time and efforts from natural products. In this review, we have provided an update on natural products including fruits, vegetables, spices, nuts, beverages and mushrooms with potential antidiabetic activities from in vivo, in vitro and clinical studies. Synergistic interactions between natural products and antidiabetic drugs; and potential antidiabetic active compounds from natural products are also documented to pave the way for combination treatment and new drug discovery, respectively. Additionally, a brief idea of the drug discovery process along with the challenges that arise during drug development from natural products and the methods to conquer those challenges are discussed to create a more convenient future drug discovery process.

Enhanced α-ketoglutaric acid production and recovery in Yarrowia lipolytica yeast by effective pH controlling.

PubMed

Morgunov, Igor G; Kamzolova, Svetlana V; Samoilenko, Vladimir A

2013-10-01

The replacement of chemical synthesis by environmentally friendly energy-efficient technologies for production of valuable metabolites is a principal strategy of developing biotechnological industry all over the world. In the present study, we develop a method for α-ketoglutaric acid (KGA) production from rapeseed oil with the use of Yarrowia lipolytica yeast. Sixty strains of Y. lipolytica yeasts were tested for their ability to produce KGA, and the strain Y. lipolytica 212 (Y. lipolytica VKM Y-2412) was selected as a promising KGA producer. Using a three-stage pH controlling, in which pH was 4.5 in the growth phase, then since 72 to 144 h, pH was maintained at 3.5 and in the later phase of acid production, the titration by KOH was switch off, selected strain produced 106.5 g l(-1) of KGA with mass yield of 0.95 g g(-1). KGA in the form of monopotassium salt was isolated from the culture broth and purified. The isolation procedure involved separation of biomass, extraction of residual triglycerides, filtrate bleaching, and acidification with mineral acid (to pH 2.8-3.4), concentration, precipitation of mineral salts, and crystallization of the product. The purity of KGA isolated from the culture filtrate reached 99.1 %.

Nutrition and bioprocess development for efficient biosynthesis of an antitumor compound from marine-derived fungus.

PubMed

Zhou, Weiqiang; Cai, Menghao; Zhou, Jiushun; Jiang, Tao; Zhou, Jiao; Wang, Meixia; Zhou, Xiangshan; Zhang, Yuanxing

2013-10-01

An integrated nutrition and bioprocess strategy was developed for improving the biosynthesis of an antitumor compound, 1403C, by a marine-derived fungus, Halorosellinia sp. (no. 1403). First, statistical design strategies were synthetically applied to optimize the nutritional composition. The resulting 1403C production reached 2.07 g/l, which was 143.5 % higher than the original production. However, it only produced 0.44 g/l of 1403C in 5-l bioreactor fermentation. Thus, the operating parameters including culture pH, dissolved oxygen, agitation speed, impeller type and inoculum level were considered to improve the fermentation process, and an effective control strategy for 1403C production by Halorosellinia sp. submerged in a 5-l bioreactor was established. When inoculating 0.22 g/l dry biomass, controlling dissolved oxygen not lower than 30 % during the growth phase but ranging between 30 and 40 % during the stationary phase, using a double-layer six-flat-blade Rushton disc turbine agitated at 400 rpm, keeping short-term low pH and rapid-rising pH with glucose starvation, the highest 1403C production was finally obtained at 1.32 g/l, which was promoted by 200 % compared to before optimization. Fermentation scale-up was finally performed in a 500-l bioreactor, and 1403C production of 1.09 g/l was obtained.

Advanced wind turbine near-term product development. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1996-01-01

In 1990 the US Department of Energy initiated the Advanced Wind Turbine (AWT) Program to assist the growth of a viable wind energy industry in the US. This program, which has been managed through the National Renewable Energy Laboratory (NREL) in Golden, Colorado, has been divided into three phases: (1) conceptual design studies, (2) near-term product development, and (3) next-generation product development. The goals of the second phase were to bring into production wind turbines which would meet the cost goal of $0.05 kWh at a site with a mean (Rayleigh) windspeed of 5.8 m/s (13 mph) and a verticalmore » wind shear exponent of 0.14. These machines were to allow a US-based industry to compete domestically with other sources of energy and to provide internationally competitive products. Information is given in the report on design values of peak loads and of fatigue spectra and the results of the design process are summarized in a table. Measured response is compared with the results from mathematical modeling using the ADAMS code and is discussed. Detailed information is presented on the estimated costs of maintenance and on spare parts requirements. A failure modes and effects analysis was carried out and resulted in approximately 50 design changes including the identification of ten previously unidentified failure modes. The performance results of both prototypes are examined and adjusted for air density and for correlation between the anemometer site and the turbine location. The anticipated energy production at the reference site specified by NREL is used to calculate the final cost of energy using the formulas indicated in the Statement of Work. The value obtained is $0.0514/kWh in January 1994 dollars. 71 figs., 30 tabs.« less

Effect of additional of Hoodia Gordonii and seaweed powder on the sensory and physicochemical properties of brown rice bar

NASA Astrophysics Data System (ADS)

Hajal, Masturah Ebni; Ghani, Maaruf Abd; Daud, Norlida Mat

2015-09-01

Awareness of the nutritional content of food has increased with the emergence of various health products in the market. Cereal bar is one of the beneficial foods among consumer that concern on their healthy food. This study was conducted to develop a brown rice bar that contain active ingredients (H. gordonii and seaweed powder) and to determine the effect on sensory evaluation and physicochemical properties (colour, texture and proximate analysis) of this product. This study consisted of two phases in which the first phase consisted of development of ten formulations including control. All of the formulations were undergo analysis of colour, texture and sensory evaluation. Based on the sensory evaluation, Control (H. gordonii: 0%, seaweed: 0%) and two best formulations that consist of formulation 6 (H. gordonii: 1.6%; seaweed: 2.8%) and formulation 9 (H. gordonii: 2.4%, seaweed: 2.8%) were chosen to undergo the second phase which is proximate analysis. Base on the result, were significant different (p<0.05) on proximate analysis except for the protein and moisture content. Therefore, it can be concluded that H. gordonii is a good source of fiber when adding in a bar.

Development and validation of an LC-UV method for the quantification and purity determination of the novel anticancer agent C1311 and its pharmaceutical dosage form.

PubMed

den Brok, Monique W J; Nuijen, Bastiaan; Hillebrand, Michel J X; Grieshaber, Charles K; Harvey, Michael D; Beijnen, Jos H

2005-09-01

C1311 (5-[[2-(diethylamino)ethyl]amino]-8-hydroxyimidazo [4,5,1-de]-acridin-6-one-dihydrochloride trihydrate) is the lead compound from the group of imidazoacridinones, a novel group of rationally designed anticancer agents. The pharmaceutical development of C1311 necessitated the availability of an assay for the quantification and purity determination of C1311 active pharmaceutical ingredient (API) and its pharmaceutical dosage form. A reversed-phase liquid chromatographic method (RP-LC) with ultraviolet (UV) detection was developed, consisting of separation on a C18 column with phosphate buffer (60 mM; pH 3 with 1 M citric acid)-acetonitrile-triethylamine (83:17:0.05, v/v/v) as the mobile phase and UV-detection at 280 nm. The method was found to be linear over a concentration range of 2.50-100 microg/mL, precise and accurate. Accelerated stress testing showed degradation products, which were well separated from the parent compound, confirming its stability-indicating capacity. Moreover, the use of LC-MS and on-line photo diode array detection enabled us to propose structures for four degradation products. Two of these products were also found as impurities in the API and more abundantly in an impure lot of API.

Comparison of tubular and panel type photobioreactors for biohydrogen production utilizing Chlamydomonas reinhardtii considering mixing time and light intensity.

PubMed

Oncel, S; Kose, A

2014-01-01

Two different photobioreactor designs; tubular and panel, were investigated for the biohydrogen production utilizing a green microalgae Chlamydomonas reinhardtii strain CC124 following the two stage protocol. Mixing time and light intensity of the systems were adjusted to compare the productivity of both aerobic culture phase and the following anaerobic biohydrogen production phase. The results showed there was an effect on both phases related with the design. During the aerobic phase bigger illumination area serving more energy, tubular photobioreactor reached higher biomass productivity of 31.8±2.1 mg L(-1) h(-1) which was about 11% higher than the panel photobioreactor. On the other hand biohydrogen productivity in the panel photobioreactor reached a value of 1.3±0.05 mL L(-1) h(-1) based on the efficient removal of biohydrogen gas. According to the results it would be a good approach to utilize tubular design for aerobic phase and panel for biohydrogen production phase. Copyright © 2013 Elsevier Ltd. All rights reserved.

Treatment of aqueous phase of bio-oil by granular activated carbon and evaluation of biogas production.

PubMed

Shanmugam, Saravanan R; Adhikari, Sushil; Wang, Zhouhang; Shakya, Rajdeep

2017-01-01

Hydrothermal liquefaction of wet biomass such as algae is a promising thermochemical process for the production of bio-oil. Bio-oil aqueous phase generated during liquefaction process is rich in complex organics and can be utilized for biogas production following its pre-treatment with granular activated carbon. In our study, use of 30% activated carbon resulted in higher chemical oxygen demand (COD) reduction (53±0.3%) from aqueous phase. Higher CH 4 production (84±12mL/gCOD) was also observed in 30% carbon-treated aqueous phase fed cultures, whereas only 32±6mLCH 4 /gCOD was observed in control (non-carbon treated) cultures. The results from this study indicate that almost 67±0.3% initial COD of aqueous phase can be reduced using a combination of both carbon treatment and biogas production. This study shows that aqueous phase can be utilized for CH 4 production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Integration of Satellite-Derived Cloud Phase, Cloud Top Height, and Liquid Water Path into an Operational Aircraft Icing Nowcasting System

NASA Technical Reports Server (NTRS)

Haggerty, Julie; McDonough, Frank; Black, Jennifer; Landott, Scott; Wolff, Cory; Mueller, Steven; Minnis, Patrick; Smith, William, Jr.

2008-01-01

Operational products used by the U.S. Federal Aviation Administration to alert pilots of hazardous icing provide nowcast and short-term forecast estimates of the potential for the presence of supercooled liquid water and supercooled large droplets. The Current Icing Product (CIP) system employs basic satellite-derived information, including a cloud mask and cloud top temperature estimates, together with multiple other data sources to produce a gridded, three-dimensional, hourly depiction of icing probability and severity. Advanced satellite-derived cloud products developed at the NASA Langley Research Center (LaRC) provide a more detailed description of cloud properties (primarily at cloud top) compared to the basic satellite-derived information used currently in CIP. Cloud hydrometeor phase, liquid water path, cloud effective temperature, and cloud top height as estimated by the LaRC algorithms are into the CIP fuzzy logic scheme and a confidence value is determined. Examples of CIP products before and after the integration of the LaRC satellite-derived products will be presented at the conference.

Development of a portable petroleum by-products chemical sensor, phase 1 and 2 report.

DOT National Transportation Integrated Search

2006-07-31

We have proposed to tailor design nanoparticle based chemical sensors for the sensitive, selective and field portable analyses of soil samples for petroleum spill indicating hydrocarbons (such as benzene, toluene, ethyl-benzenes, xylenes, PCBs, trich...

14 CFR § 1240.102 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... experimental or beta phase of development, that performs in accordance with its specifications, and includes... mathematical, engineering or scientific concept, idea, design, process, or product. (h) Innovator means any..., method, process, machine, manufacture, design, or composition of matter, or any new and useful...

How to Get What You Need (and Want) from Your Multimedia Vendor.

ERIC Educational Resources Information Center

David, Andrea Granick

1995-01-01

Outlines strategies for a successful collaboration with multimedia vendors. Topics include vendor and client responsibilities; six phases of a multimedia project, including analysis, design, audiovisual production, development/programming, implementation, and evaluation; and potential problems and solutions. (LRW)

Development of a portable petroleum by-products chemical sensor : phase III and IV.

DOT National Transportation Integrated Search

2009-08-21

Semiconductor quantum dots (QDs) are considered to have potential for chemical sensing application : because of their high surface to volume ratio and unique size tunable properties like : photoluminescence (PL). However, our study revealed for the f...

Recovery of Navy distillate fuel from reclaimed product. Volume I. Technical discussion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brinkman, D.W.; Whisman, M.L.

1984-11-01

In an effort to assist the Navy to better utilize its waste hydrocarbons, NIPER, with support from the US Department of Energy, is conducting research designed to ultimately develop a practical technique for converting Reclaimed Product (RP) into specification Naval Distillate Fuel (F-76). The first phase of the project was focused on reviewing the literature and available information from equipment manufacturers. The literature survey has been carefully culled for methodology applicable to the conversion of RP into diesel fuel suitable for Navy use. Based upon the results of this study, a second phase has been developed and outlined in whichmore » experiments will be performed to determine the most practical recycling technologies. It is realized that the final selection of one particular technology may be site-specific due to vast differences in RP volume and available facilities. A final phase, if funded, would involve full-scale testing of one of the recommended techniques at a refueling depot. The Phase I investigations are published in two volumes. Volume 1, Technical Discussion, includes the narrative and Appendices I and II. Appendix III, a detailed Literature Review, includes both a narrative portion and an annotated bibliography containing about 800 referenvces and abstracts. This appendix, because of its volume, has been published separately as Volume 2. 18 figures, 4 tables.« less

Acceptability of a novel vaginal microbicide during a safety trial among low-risk women.

PubMed

Bentley, M E; Morrow, K M; Fullem, A; Chesney, M A; Horton, S D; Rosenberg, Z; Mayer, K H

2000-01-01

The increasing recognition that women who are unable or unwilling to discuss or use condoms with their sexual partners need female-controlled methods for preventing sexually transmitted diseases (STDs), including HIV, has led to considerable focus on the development of vaginal microbicides. While many such products are being tested for safety and effectiveness, clinical trials generally overlook another key factor in a product's impact on infection rates-its acceptability to users. A Phase I clinical trial of a microbicidal gel included an assessment of the product's acceptability among 27 low-risk participants. Information on acceptability was gathered from structured interviews, participants' daily diaries and unstructured exit interviews. Participants reported only minor side effects of product use, such as itching, burning and difficulty urinating; two women developed candida infections while participating in the study. None of the side effects could be conclusively linked to use of the gel. Some women noted product discharge and messiness as drawbacks of the method, but this experience varied according to how often the women applied the gel. For example, one-third of those who used it once daily said that at least some of the time, it was too "wet or drippy," compared with two-thirds of women who inserted the gel twice a day. However, participants considered these "nuisance factors" that could be outweighed by the potential protective characteristics of the product. The majority reported that they would use the product if it were available and proven efficacious, and if they perceived that they were at risk of STD infection. Additional testing of this product is urgently needed. Furthermore, as other products approach Phase I testing, acceptability assessments should be a key component of clinical trials.

Parametric study of helicopter aircraft systems costs and weights

NASA Technical Reports Server (NTRS)

Beltramo, M. N.

1980-01-01

Weight estimating relationships (WERs) and recurring production cost estimating relationships (CERs) were developed for helicopters at the system level. The WERs estimate system level weight based on performance or design characteristics which are available during concept formulation or the preliminary design phase. The CER (or CERs in some cases) for each system utilize weight (either actual or estimated using the appropriate WER) and production quantity as the key parameters.

Joint Land Attack Cruise Missile Defense Elevated Netted Sensor System Not Ready for Production Decision (REDACTED)

DTIC Science & Technology

2012-09-07

Average Procurement Unit Cost CMDS Cruise Missile Defense Systems CPD Capability Production Document EMD Engineering and Manufacturing...Defense for Acquisition, Technology and Logistics also determined that continuing test and evaluation of the two JLENS Engineering and Manufacturing...Program (Category ID) that was established in January 1996 and, during the audit, was in the Engineering and Manufacturing Development (EMD) phase of

Our Changing Planet: The U.S. Climate Change Science Program for Fiscal Year 2006

DTIC Science & Technology

2005-11-01

any remaining uncertainties for the Amazon region of South America.These results are expected to greatly reduce errors and uncertainties concerning...changing the concentration of atmospheric CO2 are fossil -fuel burning, deforestation, land-use change, and cement production.These processes have...the initial phases of work on the remaining products. Specific plans for enhanced decision-support resources include: – Developing decision-support

Investigation of vinegar production using a novel shaken repeated batch culture system.

PubMed

Schlepütz, Tino; Büchs, Jochen

2013-01-01

Nowadays, bioprocesses are developed or optimized on small scale. Also, vinegar industry is motivated to reinvestigate the established repeated batch fermentation process. As yet, there is no small-scale culture system for optimizing fermentation conditions for repeated batch bioprocesses. Thus, the aim of this study is to propose a new shaken culture system for parallel repeated batch vinegar fermentation. A new operation mode - the flushing repeated batch - was developed. Parallel repeated batch vinegar production could be established in shaken overflow vessels in a completely automated operation with only one pump per vessel. This flushing repeated batch was first theoretically investigated and then empirically tested. The ethanol concentration was online monitored during repeated batch fermentation by semiconductor gas sensors. It was shown that the switch from one ethanol substrate quality to different ethanol substrate qualities resulted in prolonged lag phases and durations of the first batches. In the subsequent batches the length of the fermentations decreased considerably. This decrease in the respective lag phases indicates an adaptation of the acetic acid bacteria mixed culture to the specific ethanol substrate quality. Consequently, flushing repeated batch fermentations on small scale are valuable for screening fermentation conditions and, thereby, improving industrial-scale bioprocesses such as vinegar production in terms of process robustness, stability, and productivity. Copyright © 2013 American Institute of Chemical Engineers.

Formulation and Characterization of Polymeric Films Containing Combinations of Antiretrovirals (ARVs) for HIV Prevention

PubMed Central

Akil, Ayman; Agashe, Hrushikesh; Dezzutti, Charlene S.; Moncla, Bernard J.; Hillier, Sharon L.; Devlin, Brid; Shi, Yuan; Uranker, Kevin; Rohan, Lisa Cencia

2014-01-01

Purpose To develop polymeric films containing dual combinations of anti-HIV drug candidate tenofovir, maraviroc and dapivirine for vaginal application as topical microbicides. Methods A solvent casting method was used to manufacture the films. Solid phase solubility was used to identify potential polymers for use in the film formulation. Physical and chemical properties (such as water content, puncture strength and in vitro release) and product stability were determined. The bioactivity of the film products against HIV was assessed using the TZM-bl assay and a cervical explant model. Results Polymers identified from the solid phase solubility study maintained tenofovir and maraviroc in an amorphous state and prevented drug crystallization. Three combination film products were developed using cellulose polymers and polyvinyl alcohol. The residual water content in all films was < 10% (w/w). All films delivered the active agents with release of > 50% of film drug content within 30 minutes. Stability testing confirmed that the combination film products were stable for 12 months at ambient temperature and 6 months under stressed conditions. Antiviral activity was confirmed in TZM-bl and cervical explant models. Conclusions Polymeric films can be used as a stable dosage form for the delivery of antiretroviral combinations as microbicides. PMID:25079391

Expression and localization of CXCL16 and CXCR6 in ovarian endometriotic tissues.

PubMed

Manabe, Shuichi; Iwase, Akira; Goto, Maki; Kobayashi, Hiroharu; Takikawa, Sachiko; Nagatomo, Yoshinari; Nakahara, Tatsuo; Bayasula; Nakamura, Tomoko; Hirokawa, Wakana; Kikkawa, Fumitaka

2011-12-01

Inflammatory mediators, including chemokines, may play crucial roles in the development of endometriosis. Therefore, we investigated the expression and localization of CXCL16 and its receptor, CXCR6, in ovarian endometriotic tissues. We also examined whether CXCL16 induces IL-8 production in endometriotic stromal cells. We performed immunohistochemical and Western blotting analyses of in vivo and in vitro samples. IL-8 production was assayed using an ELISA. Both CXCL16 and CXCR6 were expressed by endometriotic epithelial cells and stromal cells, but not normal ovarian stroma. A Western blotting analysis using primary cultured endometriotic stromal cells showed a constant expression of CXCL16 and CXCR6 in the proliferative phase, secretory phase and during gonadotropin-releasing hormone agonist therapy. CXCL16 induced IL-8 production in several endometriotic stromal cells in vitro. CXCL16 and CXCR6 might be involved in the pathophysiology of endometriosis through regulation of the inflammatory response.

New approach to control the methanogenic reactor of a two-phase anaerobic digestion system.

PubMed

von Sachs, Jürgen; Meyer, Ulrich; Rys, Paul; Feitkenhauer, Heiko

2003-03-01

A new control strategy for the methanogenic reactor of a two-phase anaerobic digestion system has been developed and successfully tested on the laboratory scale. The control strategy serves the purpose to detect inhibitory effects and to achieve good conversion. The concept is based on the idea that volatile fatty acids (VFA) can be measured in the influent of the methanogenic reactor by means of titration. Thus, information on the output (methane production) and input of the methanogenic reactor is available, and a (carbon) mass balance can be obtained. The control algorithm comprises a proportional/integral structure with the ratio of (a) the methane production rate measured online and (b) a maximum methane production rate expected (derived from the stoichiometry) as a control variable. The manipulated variable is the volumetric feed rate. Results are shown for an experiment with VFA (feed) concentration ramps and for experiments with sodium chloride as inhibitor.

Ozone production process in pulsed positive dielectric barrier discharge

NASA Astrophysics Data System (ADS)

Ono, Ryo; Oda, Tetsuji

2007-01-01

The ozone production process in a pulsed positive dielectric barrier discharge (DBD) is studied by measuring the spatial distribution of ozone density using a two-dimensional laser absorption method. DBD occurs in a 6 mm point-to-plane gap with a 1 mm-thick glass plate placed on the plane electrode. First, the propagation of DBD is observed using a short-gated ICCD camera. It is shown that DBD develops in three phases: primary streamer, secondary streamer and surface discharge phases. Next, the spatial distribution of ozone density is measured. It is shown that ozone is mostly produced in the secondary streamer and surface discharge, while only a small amount of ozone is produced in the primary streamer. The rate coefficient of the ozone production reaction, O + O2 + M → O3 + M, is estimated to be 2.5 × 10-34 cm6 s-1.

Precision requirements and innovative manufacturing for ultrahigh precision laser interferometry of gravitational-wave astronomy

NASA Astrophysics Data System (ADS)

Ni, Wei-Tou; Han, Sen; Jin, Tao

2016-11-01

With the LIGO announcement of the first direct detection of gravitational waves (GWs), the GW Astronomy was formally ushered into our age. After one-hundred years of theoretical investigation and fifty years of experimental endeavor, this is a historical landmark not just for physics and astronomy, but also for industry and manufacturing. The challenge and opportunity for industry is precision and innovative manufacturing in large size - production of large and homogeneous optical components, optical diagnosis of large components, high reflectance dielectric coating on large mirrors, manufacturing of components for ultrahigh vacuum of large volume, manufacturing of high attenuating vibration isolation system, production of high-power high-stability single-frequency lasers, production of high-resolution positioning systems etc. In this talk, we address the requirements and methods to satisfy these requirements. Optical diagnosis of large optical components requires large phase-shifting interferometer; the 1.06 μm Phase Shifting Interferometer for testing LIGO optics and the recently built 24" phase-shifting Interferometer in Chengdu, China are examples. High quality mirrors are crucial for laser interferometric GW detection, so as for ring laser gyroscope, high precision laser stabilization via optical cavities, quantum optomechanics, cavity quantum electrodynamics and vacuum birefringence measurement. There are stringent requirements on the substrate materials and coating methods. For cryogenic GW interferometer, appropriate coating on sapphire or silicon are required for good thermal and homogeneity properties. Large ultrahigh vacuum components and high attenuating vibration system together with an efficient metrology system are required and will be addressed. For space interferometry, drag-free technology and weak-light manipulation technology are must. Drag-free technology is well-developed. Weak-light phase locking is demonstrated in the laboratories while weak-light manipulation technology still needs developments.

Subsurface injection of combustion power plant effluent as a solid-phase carbon dioxide storage strategy

NASA Astrophysics Data System (ADS)

Darnell, K. N.; Flemings, P. B.; DiCarlo, D.

2017-06-01

Long-term geological storage of CO2 may be essential for greenhouse gas mitigation, so a number of storage strategies have been developed that utilize a variety of physical processes. Recent work shows that injection of combustion power plant effluent, a mixture of CO2 and N2, into CH4 hydrate-bearing reservoirs blends CO2 storage with simultaneous CH4 production where the CO2 is stored in hydrate, an immobile, solid compound. This strategy creates economic value from the CH4 production, reduces the preinjection complexity since costly CO2 distillation is circumvented, and limits leakage since hydrate is immobile. Here we explore the phase behavior of these types of injections and describe the individual roles of H2O, CO2, CH4, and N2 as these components partition into aqueous, vapor, hydrate, and liquid CO2 phases. Our results show that CO2 storage in subpermafrost or submarine hydrate-forming reservoirs requires coinjection of N2 to maintain two-phase flow and limit plugging.

Current good manufacturing practice and investigational new drugs intended for use in clinical trials. Final rule.

PubMed

2008-07-15

The Food and Drug Administration (FDA) is amending the current good manufacturing practice (CGMP) regulations for human drugs, including biological products, to exempt most phase 1 investigational drugs from complying with the regulatory CGMP requirements. FDA will continue to exercise oversight of the manufacture of these drugs under FDA's general statutory CGMP authority and through review of the investigational new drug applications (IND). In addition, elsewhere in this issue of the Federal Register, FDA is announcing the availability of a guidance document entitled "Guidance for Industry: CGMP for Phase 1 Investigational Drugs" dated November 2007 (the companion guidance). This guidance document sets forth recommendations on approaches to compliance with statutory CGMP for the exempted phase 1 investigational drugs. FDA is taking this action to focus a manufacturer's effort on applying CGMP that is appropriate and meaningful for the manufacture of the earliest stage investigational drug products intended for use in phase 1 clinical trials while ensuring safety and quality. This action will also streamline and promote the drug development process.

Clinical evaluation of seven anticalculus dentifrice formulations.

PubMed

Scruggs, R R; Stewart, P W; Samuels, M S; Stamm, J W

1991-01-01

One hundred ninety-two subjects completed a clinical trial to determine the effects of seven dentifrice formulations on calculus inhibition. The double-blind study involved a ten-day control phase and a ten-day experimental phase. For the control phase, subjects were evaluated for calculus present, received a prophylaxis and had pre-weighed mylar strips attached to the lingual surfaces of the mandibular incisors to harvest mineral deposits. Subjects were then assigned the placebo dentifrice for unsupervised twice-daily use and were required to report once a day for a supervised mouthrinse using a 1:3 dilution of the dentrifice. The experimental phase was identical except that subjects were allocated the experimental dentifices using a stratified random assignment based on age, gender and the initial presence of calculus. Simple linear regression analyses of the dry and ash log weights obtained from the strips were performed. The results showed no statistically significant differences among the test products; however, two formulations containing zinc citrate showed some calculus inhibition-potential suggesting that further research and development of such products may be warranted.

Mapping of information and identification of construction waste at project life cycle

NASA Astrophysics Data System (ADS)

Wibowo, Mochamad Agung; Handayani, Naniek Utami; Nurdiana, Asri; Sholeh, Moh Nur; Pamungkas, Gita Silvia

2018-03-01

The development of construction project towards green construction is needed in order to improve the efficiency of construction projects. One that needs to be minimized is construction waste. Construction waste is waste generated from construction project activities, both solid waste and non solid waste. More specifically, the waste happens at every phase of the project life cycle. Project life cycle are the stage of idea, design, construction, and operation/maintenance. Each phase is managed by different stakeholders. Therefore it requires special handling from the involved stakeholders. The objective of the study is to map the information and identify the waste at each phase of the project life cycle. The purpose of mapping is to figure out the process of information and product flow and with its timeline. This mapping used Value Stream Mapping (VSM). Identification of waste was done by distributing questionnaire to respondents to know the waste according to owner, consultant planner, contractor, and supervisory consultant. The result of the study is the mapping of information flow and product flow at the phases of idea, design, construction, and operation/ maintenance.

Empirical Studies Development Of Creative Industry Its Contribution To Make-Up Of Product Orientation Exporting In Denpasar-Bali

NASA Astrophysics Data System (ADS)

Suryathi, W.; Gede, I. G. K.

2018-01-01

The puIDRose of this study are : 1) to study the model of development of creative industries which export-oriented in Denpasar 2) to examine the main problems and constraints faced by creative industries 3) to know the increasing of product export in Denpasar.The number of samples are 15 creatives industries such as sub-sector of handicraft, fashion and culinary. Sampling technique used cluster and puIDRosive sampling. Data collection by interview, observation, literature study and questioner. Data analysis using qualitative and quantitative description. The results of this study explain: The model development of creative industry in Denpasar City basically consist of three phases that is : development input, development process and development output. The problems and business constraints in creative industries about skill and salary of human resources, capital of financial, promotion of marketing, raw material of resources, technology and modern administration of production. From the product export showed that woods were hight one of crafting sub sector, textiles were hight one of fashion sub sector, tuna fish were hight one of culinary sub sector.

Use of Spray-Dried Dispersions in Early Pharmaceutical Development: Theoretical and Practical Challenges.

PubMed

Li, Jinjiang; Patel, Dhaval; Wang, George

2017-03-01

Spray-dried dispersions (SDDs) have become an important formulation technology for the pharmaceutical product development of poorly water-soluble (PWS) compounds. Although this technology is now widely used in the industry, especially in the early-phase development, the lack of mechanistic understanding still causes difficulty in selecting excipients and predicting stability of SDD-based drug products. In this review, the authors aim to discuss several principles of polymer science pertaining to the development of SDDs, in terms of selecting polymers and solvents, optimizing drug loading, as well as assessing physical stability on storage and supersaturation maintenance after dissolution, from both thermodynamic and kinetic considerations. In order to choose compatible solvents with both polymers and active pharmaceutical ingredients (APIs), a symmetric Flory-Huggins interaction (Δχ ∼0) approach was introduced. Regarding spray drying of polymer-API solutions, low critical solution temperature (LCST) was discussed for setting the inlet temperature for drying. In addition, after being exposed to moisture, SDDs are practically converted to ternary systems with asymmetric Flory-Huggins interactions, which are thermodynamically not favored. In this case, the kinetics of phase separation plays a significant role during the storage and dissolution of SDD-based drug products. The impact of polymers on the supersaturation maintenance of APIs in dissolution media was also discussed. Moreover, the nature of SDDs, with reference to solid solution and the notion of solid solubility, was examined in the context of pharmaceutical application. Finally, the importance of robust analytical techniques to characterize the SDD-based drug products was emphasized, considering their complexity.

Trade-offs mathematical modelling of 3DCE in new product development: real three dimensions and directions for development

NASA Astrophysics Data System (ADS)

Ilhami, M. A.; Subagyo; Masruroh, N. A.

2018-04-01

In the last two decades, coordinating product, process, and supply chain has become the main focus in recent years as a growing body of research, which mathematical modelling is leading technique used in the early phase design. In this paper, we aim to conduct a comprehensive literature review of published paper and propose directions for future research, especially in mathematical modelling. Our findings exhibit fact that evidently there are only a few papers coordinate “real three dimensions”. The other papers, in fact, show simply two dimensions. Finally, some suggestions are proposed such as paying more attention to “real three dimensions” research-based and more focus on minimizing time to market, product life cycle consideration, and product rollover.

Non-intrusive telemetry applications in the oilsands: from visible light and x-ray video to acoustic imaging and spectroscopy

NASA Astrophysics Data System (ADS)

Shaw, John M.

2013-06-01

While the production, transport and refining of oils from the oilsands of Alberta, and comparable resources elsewhere is performed at industrial scales, numerous technical and technological challenges and opportunities persist due to the ill defined nature of the resource. For example, bitumen and heavy oil comprise multiple bulk phases, self-organizing constituents at the microscale (liquid crystals) and the nano scale. There are no quantitative measures available at the molecular level. Non-intrusive telemetry is providing promising paths toward solutions, be they enabling technologies targeting process design, development or optimization, or more prosaic process control or process monitoring applications. Operation examples include automated large object and poor quality ore during mining, and monitoring the thickness and location of oil water interfacial zones within separation vessels. These applications involve real-time video image processing. X-ray transmission video imaging is used to enumerate organic phases present within a vessel, and to detect individual phase volumes, densities and elemental compositions. This is an enabling technology that provides phase equilibrium and phase composition data for production and refining process development, and fluid property myth debunking. A high-resolution two-dimensional acoustic mapping technique now at the proof of concept stage is expected to provide simultaneous fluid flow and fluid composition data within porous inorganic media. Again this is an enabling technology targeting visualization of diverse oil production process fundamentals at the pore scale. Far infrared spectroscopy coupled with detailed quantum mechanical calculations, may provide characteristic molecular motifs and intermolecular association data required for fluid characterization and process modeling. X-ray scattering (SAXS/WAXS/USAXS) provides characteristic supramolecular structure information that impacts fluid rheology and process fouling. The intent of this contribution is to present some of the challenges and to provide an introduction grounded in current work on non-intrusive telemetry applications - from a mine or reservoir to a refinery!

ASI-Volcanic Risk System (SRV): a pilot project to develop EO data processing modules and products for volcanic activity monitoring, first results.

NASA Astrophysics Data System (ADS)

Silvestri, M.; Musacchio, M.; Buongiorno, M. F.; Dini, L.

2009-04-01

The Project called Sistema Rischio Vulcanico (SRV) is funded by the Italian Space Agency (ASI) in the frame of the National Space Plan 2003-2005 under the Earth Observations section for natural risks management. The SRV Project is coordinated by the Istituto Nazionale di Geofisica e Vulcanologia (INGV) which is responsible at national level for the volcanic monitoring. The project philosophy is to implement, by incremental versions, specific modules which allow to process, store and visualize through Web GIS tools geophysical parameters suitable for volcanic risk management. The ASI-SRV is devoted to the development of an integrated system based on Earth Observation (EO) data to respond to specific needs of the Italian Civil Protection Department (DPC) and improve the monitoring of Italian active volcanoes during all the risk phases (Pre Crisis, Crisis and Post Crisis). The ASI-SRV system provides support to risk managers during the different volcanic activity phases and its results are addressed to the Italian Civil Protection Department (DPC). SRV provides the capability to manage the import many different EO data into the system, it maintains a repository where the acquired data have to be stored and generates selected volcanic products. The processing modules for EO Optical sensors data are based on procedures jointly developed by INGV and University of Modena. This procedures allow to estimate a number of parameters such as: surface thermal proprieties, gas, aerosol and ash emissions and to characterize the volcanic products in terms of composition and geometry. For the analysis of the surface thermal characteristics, the available algorithms allow to extract information during the prevention phase and during the Warning and Crisis phase. In the prevention phase the thermal analysis is directed to the identification of temperature variation on volcanic structure which may indicate a change in the volcanic activity state. At the moment the only sensor that shows good technical characteristics for the prevention phase is the ASTER sensor (90 m pixel) on NASA satellite TERRA. The product regarding the Crisis phase is mainly finalized to the estimation of the effusion rate for active lava flows, the algorithms for this product are well consolidated and could be applied to the low spatial resolution space sensors (eg. AVHRR, MODIS) and to high spatial resolution space sensors (eg. Hyperion, ASTER). A further class of products regards the analysis of degassing plumes and eruptive clouds. The analysis of the emitted gas species from degassing plume is usually performed trough ground networks of instruments based on the spectral behaviour of the gas species, although many volcanoes in the world do not have such permanent networks. The SRV system will produce information on the concentration and flux of sulphur dioxide (SO2) water vapour and volcanic aerosol optical thickness by means of ASTER, MODIS and HYPERION data on Etna test site. The analysis of ash clouds will be made by means of already consolidated procedures which uses low spatial resolution sensors with an high revisit time (eg. AVHRR, MSG, MODIS). For the Post Crisis phase the required products will be obtained through classification algorithms and spectral analysis operated by the scientific personnel of INGV and introduced in the system repository after the use of modules. The processing modules for EO RADAR sensors data for ground deformation measurement via Differential Interferometric SAR (DInSAR) techniques is performed by IREA-CNR. The selected test sites are Etna, Vesuvius and Campi Flegrei caldera. In particular, ground deformation time series will be generated by using ERS and ENVISAT SAR data and via the application of the Small BAeline Subset (SBAS) technique. This algorithm has the advantage of being both simple and very effective; moreover, it allows an easy combination of multiplatform data, provided that the acquisition geometries of both platform are compatible. In this paper the first results obtained by means of modules developed within the ASI-SRV project and dedicated to the processing of EO historical series are presented.

APT, The Phase I tool for HST Cycle 12

NASA Astrophysics Data System (ADS)

Blacker, Brett S.; Bertch, Maria; Curtis, Gary; Douglas, Robert E., Jr.; Krueger, Anthony P.

2002-12-01

In the continuing effort to streamline our systems and improve service to the science community, the Space Telescope Science Institute (STScI) is developing and releasing, APT The Astronomer’s Proposal Tool as the new interface for Hubble Space Telescope (HST) Phase I and Phase II proposal submissions for HST Cycle 12. APT, was formerly called the Scientist’s Expert Assistant (SEA), which started as a prototype effort to try and bring state of the art technology, more visual tools and power into the hands of proposers so that they can optimize the scientific return of their programs as well as HST. Proposing for HST and other missions, consists of requesting observing time and/or archival research funding. This step is called Phase I, where the scientific merit of a proposal is considered by a community based peer-review process. Accepted proposals then proceed thru Phase II, where the observations are specified in sufficient detail to enable scheduling on the telescope. In this paper, we will present our concept and implementation plans for our Phase I development and submission tool, APT. More importantly, we will go behind the scenes and discuss why it’s important for the Science Policies Division (SPD) and other groups at the STScI to have a new submission tool and submission output products. This paper is an update of the status of the HST Phase I Proposal Processing System that was described in the published paper “A New Era for HST Phase I Development and Submission.”

Offline solid-phase extraction for preconcentration of pharmaceuticals and personal care products in environmental water and their simultaneous determination using the reversed phase high-performance liquid chromatography method.

PubMed

G Archana; Dhodapkar, Rita; Kumar, Anupama

2016-09-01

The present study reports a precise and simple offline solid-phase extraction (SPE) coupled with reversed-phase high-performance liquid chromatography (RP-HPLC) method for the simultaneous determination of five representative and commonly present pharmaceuticals and personal care products (PPCPs), a new class of emerging pollutants in the aquatic environment. The target list of analytes including ciprofloxacin, acetaminophen, caffeine benzophenone and irgasan were separated by a simple HPLC method. The column used was a reversed-phase C18 column, and the mobile phase was 1 % acetic acid and methanol (20:80 v/v) under isocratic conditions, at a flow rate of 1 mL min(-1). The analytes were separated and detected within 15 min using the photodiode array detector (PDA). The linearity of the calibration curves were obtained with correlation coefficients 0.98-0.99.The limit of detection (LOD), limit of quantification (LOQ), precision, accuracy and ruggedness demonstrated the reproducibility, specificity and sensitivity of the developed method. Prior to the analysis, the SPE was performed using a C18 cartridge to preconcentrate the targeted analytes from the environmental water samples. The developed method was applied to evaluate and fingerprint PPCPs in sewage collected from a residential engineering college campus, polluted water bodies such as Nag river and Pili river and the influent and effluent samples from a sewage treatment plant (STP) situated at Nagpur city, in the peak summer season. This method is useful for estimation of pollutants present in microquantities in the surface water bodies and treated sewage as compared to nanolevel pollutants detected by mass spectrometry (MS) detectors.

Controlling Listeria monocytogenes and Leuconostoc mesenteroides in Uncured Deli-style Turkey Breast Using a Clean Label Antimicrobial.

PubMed

Weyker, Robert E; Glass, Kathleen A; Milkowski, Andrew L; Seman, Dennis L; Sindelar, Jeffrey J

2016-03-01

Interest in natural/organic meat products has resulted in the need to validate the effectiveness of clean label antimicrobials to increase safety and shelf life of these products. A Response Surface Methodology (RSM) was used to investigate the effects of varying levels of moisture, pH, and a commercial "clean-label" antimicrobial (cultured sugar-vinegar blend; CSVB) on the growth rate of Listeria monocytogenes and Leuconostoc mesenteroides in uncured turkey stored at 4 °C for 16 wk. Twenty treatment combinations of moisture (60% to 80%), pH (5.8 to 6.4), and CSVB (2.5% to 5.0%) were evaluated during phase I to develop growth curves for both microbe types, whereas the interactive effects of pH (5.8 to 6.4) and CSVB (0.0 to 4.75) were tested in 16 treatment combinations during Phase II at a single moisture level using L. monocytogenes only. CSVB inhibited L. monocytogenes growth in 14 of the 20 treatments tested in Phase I and in 12 of the 16 treatments in Phase II through 16 and 8 wk, respectively. In contrast, CSVB had little effect on L. mesenteroides, with growth inhibited in only 4 of 20 treatments in Phase I and was therefore not tested further in Phase II. Significant interactions of the RSM design coefficients yielded a predictive model for L. mesenteroides growth rate, but due to lack of growth, no growth rate model was developed for L. monocytogenes. CSVB was found to be an effective antilisteral antimicrobial, while having little effect on a spoilage microorganism. © 2016 Institute of Food Technologists®

Multiphase Flow Technology Impacts on Thermal Control Systems for Exploration

NASA Technical Reports Server (NTRS)

McQuillen, John; Sankovic, John; Lekan, Jack

2006-01-01

The Two-Phase Flow Facility (TPHIFFy) Project focused on bridging the critical knowledge gap by developing and demonstrating critical multiphase fluid products for advanced life support, thermal management and power conversion systems that are required to enable the Vision for Space Exploration. Safety and reliability of future systems will be enhanced by addressing critical microgravity fluid physics issues associated with flow boiling, condensation, phase separation, and system stability. The project included concept development, normal gravity testing, and reduced gravity aircraft flight campaigns, in preparation for the development of a space flight experiment implementation. Data will be utilized to develop predictive models that could be used for system design and operation. A single fluid, two-phase closed thermodynamic loop test bed was designed, assembled and tested. The major components in this test bed include: a boiler, a condenser, a phase separator and a circulating pump. The test loop was instrumented with flow meters, thermocouples, pressure transducers and both high speed and normal speed video cameras. A low boiling point surrogate fluid, FC-72, was selected based on scaling analyses using preliminary designs for operational systems. Preliminary results are presented which include flow regime transitions and some observations regarding system stability.

Composition and automated crystal orientation mapping of rapid solidification products in hypoeutectic Al-4 at.%Cu alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zweiacker, K. W.; Liu, Can; Gordillo, M. A.

Rmore » apid solidification can produce metastable phases and unusual microstructure modifications in multi-component alloys during additive manufacturing or laser beam welding. Composition and phase mapping by transmission electron microscopy have been used in this paper to characterize the morphologically distinct zones developing in hypoeutectic Al-4 at.% Cu alloy after pulsed laser melting for different crystal growth rate regimes. Deviations of the compositions of the alloy phases from equilibrium predictions and unique orientation relationships between the solidification transformation products have been determined. Specifically, for the columnar growth zone at solidification rates of 0.8 m s - 1 < v < v a = 1.8 m s - 1 , two distinct orientation relationships were established between the concomitantly forming non-equilibrium phases, supersaturated α-Al solid solution and the discontinuously distributed α-Al 2Cu-based θ'-phase, which can be described as {110} θ ∥ {001} α, [001] θ ∥ [110] α and {001} θ ∥ {001} α, [100] θ ∥ [100] α. These orientation relationships permit formation of coherent interphase interfaces with low interfacial free energy. Finally, this endows a kinetic advantage to the thermodynamically less stable θ'-Al 2Cu phase relative to the more stable equilibrium θ-Al 2Cu phase during formation of the morphologically modified eutectic of the columnar growth zone grains, since repeated nucleation is required to establish the discontinuous distribution of θ'-Al 2Cu phase.« less

Composition and automated crystal orientation mapping of rapid solidification products in hypoeutectic Al-4 at.%Cu alloys

DOE PAGES

Zweiacker, K. W.; Liu, Can; Gordillo, M. A.; ...

2017-12-05

Rmore » apid solidification can produce metastable phases and unusual microstructure modifications in multi-component alloys during additive manufacturing or laser beam welding. Composition and phase mapping by transmission electron microscopy have been used in this paper to characterize the morphologically distinct zones developing in hypoeutectic Al-4 at.% Cu alloy after pulsed laser melting for different crystal growth rate regimes. Deviations of the compositions of the alloy phases from equilibrium predictions and unique orientation relationships between the solidification transformation products have been determined. Specifically, for the columnar growth zone at solidification rates of 0.8 m s - 1 < v < v a = 1.8 m s - 1 , two distinct orientation relationships were established between the concomitantly forming non-equilibrium phases, supersaturated α-Al solid solution and the discontinuously distributed α-Al 2Cu-based θ'-phase, which can be described as {110} θ ∥ {001} α, [001] θ ∥ [110] α and {001} θ ∥ {001} α, [100] θ ∥ [100] α. These orientation relationships permit formation of coherent interphase interfaces with low interfacial free energy. Finally, this endows a kinetic advantage to the thermodynamically less stable θ'-Al 2Cu phase relative to the more stable equilibrium θ-Al 2Cu phase during formation of the morphologically modified eutectic of the columnar growth zone grains, since repeated nucleation is required to establish the discontinuous distribution of θ'-Al 2Cu phase.« less

Product definition data interface

NASA Technical Reports Server (NTRS)

Birchfield, B.; Downey, P.

1984-01-01

The development and application of advanced Computer Aided Design/Computer Aided Manufacturing (CAD/CAM) technology in aerospace industry is discussed. New CAD/CAM capabilities provide the engineer and production worker with tools to produce better products and significantly improve productivity. This technology is expanding in all phases of engineering and manufacturing with large potential for improvements in productivity. The integration of CAD and CAM systematically to insure maximum utility throughout the U.S. Aerospace Industry, its large community of supporting suppliers, and the Department of Defense aircraft overhaul and repair facilities is outlined. The need for a framework for exchange of digital product definition data, which serves the function of the conventional engineering drawing is emphasized.

Development of Production-Intent Plug-In Hybrid Vehicle Using Advanced Lithium-Ion Battery Packs with Deployment to a Demonstration Fleet

DOE Office of Scientific and Technical Information (OSTI.GOV)

No, author

2013-09-29

The primary goal of this project was to speed the development of one of the first commercially available, OEM-produced plug-in hybrid electric vehicles (PHEV). The performance of the PHEV was expected to double the fuel economy of the conventional hybrid version. This vehicle program incorporated a number of advanced technologies, including advanced lithium-ion battery packs and an E85-capable flex-fuel engine. The project developed, fully integrated, and validated plug-in specific systems and controls by using GM’s Global Vehicle Development Process (GVDP) for production vehicles. Engineering Development related activities included the build of mule vehicles and integration vehicles for Phases I &more » II of the project. Performance data for these vehicles was shared with the U.S. Department of Energy (DOE). The deployment of many of these vehicles was restricted to internal use at GM sites or restricted to assigned GM drivers. Phase III of the project captured the first half or Alpha phase of the Engineering tasks for the development of a new thermal management design for a second generation battery module. The project spanned five years. It included six on-site technical reviews with representatives from the DOE. One unique aspect of the GM/DOE collaborative project was the involvement of the DOE throughout the OEM vehicle development process. The DOE gained an understanding of how an OEM develops vehicle efficiency and FE performance, while balancing many other vehicle performance attributes to provide customers well balanced and fuel efficient vehicles that are exciting to drive. Many vehicle content and performance trade-offs were encountered throughout the vehicle development process to achieve product cost and performance targets for both the OEM and end customer. The project team completed two sets of PHEV development vehicles with fully integrated PHEV systems. Over 50 development vehicles were built and operated for over 180,000 development miles. The team also completed four GM engineering development Buy-Off rides/milestones. The project included numerous engineering vehicle and systems development trips including extreme hot, cold and altitude exposure. The final fuel economy performance demonstrated met the objectives of the PHEV collaborative GM/DOE project. Charge depletion fuel economy of twice that of the non-PHEV model was demonstrated. The project team also designed, developed and tested a high voltage battery module concept that appears to be feasible from a manufacturability, cost and performance standpoint. The project provided important product development and knowledge as well as technological learnings and advancements that include multiple U.S. patent applications.« less

Economics of recombinant antibody production processes at various scales: Industry-standard compared to continuous precipitation.

PubMed

Hammerschmidt, Nikolaus; Tscheliessnig, Anne; Sommer, Ralf; Helk, Bernhard; Jungbauer, Alois

2014-06-01

Standard industry processes for recombinant antibody production employ protein A affinity chromatography in combination with other chromatography steps and ultra-/diafiltration. This study compares a generic antibody production process with a recently developed purification process based on a series of selective precipitation steps. The new process makes two of the usual three chromatographic steps obsolete and can be performed in a continuous fashion. Cost of Goods (CoGs) analyses were done for: (i) a generic chromatography-based antibody standard purification; (ii) the continuous precipitation-based purification process coupled to a continuous perfusion production system; and (iii) a hybrid process, coupling the continuous purification process to an upstream batch process. The results of this economic analysis show that the precipitation-based process offers cost reductions at all stages of the life cycle of a therapeutic antibody, (i.e. clinical phase I, II and III, as well as full commercial production). The savings in clinical phase production are largely attributed to the fact that expensive chromatographic resins are omitted. These economic analyses will help to determine the strategies that are best suited for small-scale production in parallel fashion, which is of importance for antibody production in non-privileged countries and for personalized medicine. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A perfusion culture system using a stirred ceramic membrane reactor for hyperproduction of IgG2a monoclonal antibody by hybridoma cells.

PubMed

Dong, Haodi; Tang, Ya-Jie; Ohashi, Ryo; Hamel, Jean-François P

2005-01-01

A novel perfusion culture system for efficient production of IgG2a monoclonal antibody (mAb) by hybridoma cells was developed. A ceramic membrane module was constructed and used as a cell retention device installed in a conventional stirred-tank reactor during the perfusion culture. Furthermore, the significance of the control strategy of perfusion rate (volume of fresh medium/working volume of reactor/day, vvd) was investigated. With the highest increasing rate (deltaD, vvd per day, vvdd) of perfusion rate, the maximal viable cell density of 3.5 x 10(7) cells/mL was obtained within 6 days without any limitation and the cell viability was maintained above 95%. At lower deltaD's, the cell growth became limited. Under nutrient-limited condition, the specific cell growth rate (mu) was regulated by deltaD. During the nonlimited growth phase, the specific mAb production rate (qmAb) remained constant at 0.26 +/- 0.02 pg/cell x h in all runs. During the cell growth-limited phase, qmAb was regulated by deltaD within the range of 0.25-0.65 vvdd. Under optimal conditions, qmAb of 0.80 and 2.15 pg/cell x h was obtained during the growth-limited phase and stationary phase, respectively. The overall productivity and yield were 690 mg/L x day and 340 mg/L x medium, respectively. This study demonstrated that this novel perfusion culture system for suspension mammalian cells can support high cell density and efficient mAb production and that deltaD is an important control parameter to regulate and achieve high mAb production.

Developing Product Environmental Footprint Category Rules (PEFCR) for shampoos - The basis for comparable Life Cycle Assessments.

PubMed

Golsteijn, Laura; Lessard, Lindsay; Campion, Jean-Florent; Capelli, Alexandre; D'Enfert, Virginie; King, Henry; Kremer, Joachim; Krugman, Michael; Orliac, Hélène; Furnemont, Severine Roullet; Schuh, Werner; Stalmans, Mark; O'Hanlon, Natasha Williams; Coroama, Manuela

2018-06-05

In 2013, the European Commission launched the Environmental Footprint Rules pilot phase. This initiative aims at setting specific rules for life cycle assessment (LCA: raw material sourcing, production, logistics, use- and disposal phase) studies within one product category, so called product environmental footprint category rules (PEFCR), as well as for organisations, so called organisational environmental footprint sector rules (OEFSR). Such specific rules for measuring environmental performance throughout the life cycle should facilitate the comparability between LCA studies, and provide principles for communicating the environmental performance, such as transparency, reliability, completeness, and clarity. Cosmetics Europe, the association representing the cosmetics industry in the EU, completed a voluntary study into the development of PEFCR for shampoo, generally following the guidelines and methodology developed by the European Commission for its own pilot projects. The study assessed the feasibility and relevance of establishing PEFCR for shampoo. Specifically, the study defines a large number of modelling assumptions and default values relevant for shampoo (e.g. for the functional unit, the system boundaries, default transport distances, rinsing water volumes, temperature differences, life cycle inventory data sources etc) that can be modified as appropriate, according to specificities of individual products, manufacturing companies and countries. The results of the study may be used to support internal decision-making (e.g. to identify 'hotspots' with high environmental impact and opportunities for improvement) or to meet information requests from commercial partners, consumers, media or authorities on product environmental characteristics. In addition, the shampoo study also highlighted many of the challenges and limitations of the current PEF methodology, namely its complexity and resource intensiveness. It highlighted two areas where improvements are much needed: (1) data quality and availability, and (2) impact assessment methodologies and robustness. Many of the learnings are applicable to other rinse-off cosmetic products such as shower gels, liquid soaps, bath products and hair conditioners. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Fully coupled two-phase flow and poromechanics modeling of coalbed methane recovery: Impact of geomechanics on production rate

DOE PAGES

Ma, Tianran; Rutqvist, Jonny; Oldenburg, Curtis M.; ...

2017-06-03

This study presents the development and application of a fully coupled two-phase (methane and water) flow, transport, and poromechanics num erical model for the analysis of geomechanical impacts on coalbed methane (CBM) production. The model considers changes in two-phase fluid flow properties, i.e., coal porosity, permeability, water retention, and relative permeability curves through changes in cleat fractures induced by effective stress variations and desorption-induced shrinkage. The coupled simulator is first verified for poromechanics coupling, and simulation parameters of a CBM reservoir model are calibrated by history matching against one year of CBM production field data from Shanxi Province, China. Then,more » the verified simulator and the calibrated CBM reservoir model are used for predicting the impact of geomechanics on the production rate for twenty years of continuous CBM production. The simulation results show that desorption-induced shrinkage is the dominant process in increasing permeability in the near wellbore region. Away from the wellbore, desorption-induced shrinkage is weaker, and permeability is reduced by pressure depletion and increased effective stress. A sensitivity analysis shows that for coal with a higher sorption strain, a larger initial Young's modulus and a smaller Poisson's ratio promote the enhancement of permeability as well as an increased production rate. Moreover, the conceptual model of the cleat system, whether dominated by vertical cleats with permeability correlated to horizontal stress or with permeability correlated to mean stress, can have a significant impact on the predicted production rate. Overall, the study clearly demonstrates and confirms the critical importance of considering geomechanics for an accurate prediction of CBM production.« less

Fully coupled two-phase flow and poromechanics modeling of coalbed methane recovery: Impact of geomechanics on production rate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma, Tianran; Rutqvist, Jonny; Oldenburg, Curtis M.

This study presents the development and application of a fully coupled two-phase (methane and water) flow, transport, and poromechanics num erical model for the analysis of geomechanical impacts on coalbed methane (CBM) production. The model considers changes in two-phase fluid flow properties, i.e., coal porosity, permeability, water retention, and relative permeability curves through changes in cleat fractures induced by effective stress variations and desorption-induced shrinkage. The coupled simulator is first verified for poromechanics coupling, and simulation parameters of a CBM reservoir model are calibrated by history matching against one year of CBM production field data from Shanxi Province, China. Then,more » the verified simulator and the calibrated CBM reservoir model are used for predicting the impact of geomechanics on the production rate for twenty years of continuous CBM production. The simulation results show that desorption-induced shrinkage is the dominant process in increasing permeability in the near wellbore region. Away from the wellbore, desorption-induced shrinkage is weaker, and permeability is reduced by pressure depletion and increased effective stress. A sensitivity analysis shows that for coal with a higher sorption strain, a larger initial Young's modulus and a smaller Poisson's ratio promote the enhancement of permeability as well as an increased production rate. Moreover, the conceptual model of the cleat system, whether dominated by vertical cleats with permeability correlated to horizontal stress or with permeability correlated to mean stress, can have a significant impact on the predicted production rate. Overall, the study clearly demonstrates and confirms the critical importance of considering geomechanics for an accurate prediction of CBM production.« less

The use of Stationary Phase Optimized Selectivity Liquid Chromatography for the development of herbal fingerprints to detect targeted plants in plant food supplements.

PubMed

Deconinck, E; Djiogo, C A Sokeng; Kamugisha, A; Courselle, P

2017-08-01

The consumption of plant food supplements is increasing steadily and more and more, these products are bought through internet. Often the products sold through internet are not registered or declared with a national authority, meaning that no or minimal quality control is performed and that they could contain herbs or plants that are regulated. Stationary Phase Optimized Selectivity Liquid Chromatography (SOS-LC) was evaluated for the development of specific fingerprints, to be used for the detection of targeted plants in plant food supplements. Three commonly used plants in plant food supplements and two regulated plants were used to develop fingerprints with SOS-LC. It was shown that for all plants specific fingerprints could be obtained, allowing the detection of these targeted plants in triturations with different herbal matrices as well as in real samples of suspicious supplements seized by the authorities. For three of the five plants a more specific fingerprint was obtained, compared to the ones developed on traditional columns described in literature. It could therefore be concluded that the combination of segments of different types of stationary phases, as used in SOS-LC, has the potential of becoming a valuable tool in the quality control and the identification of crude herbal or plant material and in the detection of regulated plants in plant food supplements or other herbal preparations. Copyright © 2017 Elsevier B.V. All rights reserved.

The Discriminant Analysis Flare Forecasting System (DAFFS)

NASA Astrophysics Data System (ADS)

Leka, K. D.; Barnes, Graham; Wagner, Eric; Hill, Frank; Marble, Andrew R.

2016-05-01

The Discriminant Analysis Flare Forecasting System (DAFFS) has been developed under NOAA/Small Business Innovative Research funds to quantitatively improve upon the NOAA/SWPC flare prediction. In the Phase-I of this project, it was demonstrated that DAFFS could indeed improve by the requested 25% most of the standard flare prediction data products from NOAA/SWPC. In the Phase-II of this project, a prototype has been developed and is presently running autonomously at NWRA.DAFFS uses near-real-time data from NOAA/GOES, SDO/HMI, and the NSO/GONG network to issue both region- and full-disk forecasts of solar flares, based on multi-variable non-parametric Discriminant Analysis. Presently, DAFFS provides forecasts which match those provided by NOAA/SWPC in terms of thresholds and validity periods (including 1-, 2-, and 3- day forecasts), although issued twice daily. Of particular note regarding DAFFS capabilities are the redundant system design, automatically-generated validation statistics and the large range of customizable options available. As part of this poster, a description of the data used, algorithm, performance and customizable options will be presented, as well as a demonstration of the DAFFS prototype.DAFFS development at NWRA is supported by NOAA/SBIR contracts WC-133R-13-CN-0079 and WC-133R-14-CN-0103, with additional support from NASA contract NNH12CG10C, plus acknowledgment to the SDO/HMI and NSO/GONG facilities and NOAA/SWPC personnel for data products, support, and feedback. DAFFS is presently ready for Phase-III development.

Practice of Regulatory Science (Drug Development).

PubMed

Kawanishi, Toru

2017-01-01

The practice of regulatory science (RS) for drug development is described. In the course material for education in pharmaceutical sciences drafted by the RS Division of the Pharmaceutical Society of Japan, RS for pharmaceuticals is defined as the science of predicting, assessing, and judging the quality, efficacy, and safety of pharmaceutical products throughout their lifespan. RS is also described as an integrated science based on basic and applied biomedical sciences, including analytical chemistry, biochemistry, pharmacology, toxicology, genetics, biostatistics, epidemiology, and clinical trial methodology, and social sciences such as decision science, risk assessment, and communication science. The involvement of RS in drug development generally starts after the optimization of lead compounds. RS plays important roles governing pharmaceuticals during their entire life cycle management phase as well as the drug development phase.

Production of coloured glass-ceramics from incinerator ash using thermal plasma technology.

PubMed

Cheng, T W; Huang, M Z; Tzeng, C C; Cheng, K B; Ueng, T H

2007-08-01

Incineration is a major treatment process for municipal solid waste in Taiwan. It is estimated that over 1.5 Mt of incinerator ash are produced annually. This study proposes using thermal plasma technology to treat incinerator ash. Sintered glass-ceramics were produced using quenched vitrified slag with colouring agents added. The experimental results showed that the major crystalline phases developed in the sintered glass-ceramics were gehlenite and wollastonite, but many other secondary phases also appeared depending on the colouring agents added. The physical/mechanical properties, chemical resistance and toxicity characteristic leaching procedure of the coloured glass-ceramics were satisfactory. The glass-ceramic products obtained from incinerator ash treated with thermal plasma technology have great potential for building applications.

[Determination of sennosides and degraded products in the process of sennoside metabolism by HPLC].

PubMed

Sun, Yan; Li, Xuetuo; Yu, Xingju

2004-01-01

A method for the separation and determination of sennosides A and B and the main composition (sennidins A and B) in degraded products of sennosides by linear gradient high performance liquid chromatography has been developed. Separation conditions were as follows: column, a Spherisorb C18 column (250 mm x 4.6 mm i.d., 10 microm); column temperature, 40 degrees C; detection wavelength, 360 nm; mobile phase A, 1.25% acetic acid aqueous solution; mobile phase B, methanol; linear gradient, 100% A --> (20 min) 100% B. The method is effective, quick, accurate and reproducible. The satisfactory results show that this new method has certain practical values as an approach of real-time analysis in the process of sennoside metabolism.

Assessing the potential of spectral induced polarization to detect in situ changes in iron reduction

NASA Astrophysics Data System (ADS)

Rosier, C. L.; Price, A.; Sharma, S.; Atekwana, E. A.

2016-12-01

The near surface geophysical technique Spectral Induced Polarization (SIP), provides promise as an effective method measuring in situ biofilm formation/development. Yet, potential mechanisms responsible for observed shifts in SIP response due to biofilm are not clearly understood. In order to address possible mechanisms we assessed the influence of Shewanella oneidensis (MR1) cell density (colony forming units; CFU), biofilm production (Bradford assay) and iron reduction metabolism (colorimetric assay) on SIP response. Laboratory measurements were collected over three months on columns packed with either iron-coated or iron-free sands and amended with artificial ground water and acetate in order to stimulate biofilm production and microbial iron reduction. Additionally, scanning electron microscopy (SEM) was used to confirm the presence of S. oneidensis cells and biofilm. Our results suggest that during early/initial stage (<30 days) of the iron-coated column incubations, both phase and imaginary conductivity response increased 4-fold as concentrations of reduced iron increased from 0-50 mM. In the later stages (>75 days) of column incubation, SIP measurements revealed that phase and imaginary conductivity responses decreased as the concentration of reduced iron decreased below 2.0 mM. In contrast, we observed only a moderate increase in phase and imaginary conductivity ( 30%) within iron-free columns as a result of increases in S. oneidensis cells (CFU 1.5 x 1011) and biofilm production (7.0 mg ml-1). SEM analysis confirmed the presence of biofilm and cells within both iron-coated and iron-free columns. We hypothesize that the production of microbial metabolic byproducts is a potential mechanism explaining large phase shits observed in previous studies ( 50 mrads) rather than the conductivity of cells or biofilm. Our findings provide support for the following: i) ratio of cells to biofilm production only moderately influences both phase and imaginary conductivity response and ii) largest phase and imaginary conductivity response resulted from microbial metabolism (i.e. iron reduction) and potentially biofilm trapping of conductive materials (i.e. cations).

National Skills Standards Development Program: Organization and Operation of Technical Committees To Develop National Skill Standards for Competency in the Electronics Industry. The Third Party Summative Evaluation of the Electronic Industries Foundation Project. Phase I & II. Final Report.

ERIC Educational Resources Information Center

Losh, Charles

The Electronics Industries Foundation was awarded a project to develop national entry-level standards and a certification system. Ten specialties were included: automotive electronics, avionics, biomedical electronics, business machines, consumer products electronics, general electronics, industrial electronics, instrumentation, microcomputer, and…

Reuse-Driven Software Processes Guidebook. Version 02.00.03

DTIC Science & Technology

1993-11-01

a required sys - tem without unduly constraining the details of the solution. The Naval Research Laboratory Software Cost Reduction project developed...conventional manner. The emphasis is still on the development of "one-of-a-kind" sys - tems and the phased completion and review of corresponding...Application Engineering to improve the life-cycle productivity of Sy - 21 OVM ftrdauntals of Syatbes the total software development enterprise. The

Efficiency improvement of an antibody production process by increasing the inoculum density.

PubMed

Hecht, Volker; Duvar, Sevim; Ziehr, Holger; Burg, Josef; Jockwer, Alexander

2014-01-01

Increasing economic pressure is the main driving force to enhance the efficiency of existing processes. We developed a perfusion strategy for a seed train reactor to generate a higher inoculum density for a subsequent fed batch production culture. A higher inoculum density can reduce culture duration without compromising product titers. Hence, a better capacity utilization can be achieved. The perfusion strategy was planned to be implemented in an existing large scale antibody production process. Therefore, facility and process constraints had to be considered. This article describes the initial development steps. Using a proprietary medium and a Chinese hamster ovary cell line expressing an IgG antibody, four different cell retention devices were compared in regard to retention efficiency and reliability. Two devices were selected for further process refinement, a centrifuge and an inclined gravitational settler. A concentrated feed medium was developed to meet facility constraints regarding maximum accumulated perfundate volume. A 2-day batch phase followed by 5 days of perfusion resulted in cell densities of 1.6 × 10(10) cells L(-1) , a 3.5 fold increase compared to batch cultivations. Two reactor volumes of concentrated feed medium were needed to achieve this goal. Eleven cultivations were carried out in bench and 50 L reactors showing acceptable reproducibility and ease of scale up. In addition, it was shown that at least three perfusion phases can be combined within a repeated perfusion strategy. © 2014 American Institute of Chemical Engineers.

[Statement: Requirements for the assessment of surgical innovations].

PubMed

Seidel, Dörthe; Pieper, Dawid; Neugebauer, Edmund

2015-01-01

The term "innovation" refers to new products, but also to the process of developing and distributing new products and procedures. The operative disciplines are often associated with innovations because of their continuous, stepwise adaptation of daily practice to established procedures. Medical devices play a significant role in integrating surgical technology with surgical experience. The success of a surgical innovation and other invasive treatments does not only depend on the surgical procedure, but also on the context of the whole treatment process including the pre- and postoperative phase, the interaction of the surgical team and the setting. High standards have been set for the assessment of surgical innovations in terms of patient safety, efficacy and patient benefit, which will be discussed in the present paper. A stepwise approach to evaluation will be used, split into preclinical development, clinical development (feasibility and safety), evaluation phase (efficacy and patient benefit) and longtime surveillance. Our paper is based on the expert-based consented IDEAL approach as well as the consented recommendations of the European Association of Endoscopic Surgery (EAES). (As supplied by publisher). Copyright © 2015. Published by Elsevier GmbH.

A validated stability-indicating UPLC method for desloratadine and its impurities in pharmaceutical dosage forms.

PubMed

Rao, Dantu Durga; Satyanarayana, N V; Malleswara Reddy, A; Sait, Shakil S; Chakole, Dinesh; Mukkanti, K

2010-02-05

A novel stability-indicating gradient reverse phase ultra-performance liquid chromatographic (RP-UPLC) method was developed for the determination of purity of desloratadine in presence of its impurities and forced degradation products. The method was developed using Waters Aquity BEH C18 column with mobile phase containing a gradient mixture of solvents A and B. The eluted compounds were monitored at 280nm. The run time was 8min within which desloratadine and its five impurities were well separated. Desloratadine was subjected to the stress conditions of oxidative, acid, base, hydrolytic, thermal and photolytic degradation. Desloratadine was found to degrade significantly in oxidative and thermal stress conditions and stable in acid, base, hydrolytic and photolytic degradation conditions. The degradation products were well resolved from main peak and its impurities, thus proved the stability-indicating power of the method. The developed method was validated as per ICH guidelines with respect to specificity, linearity, limit of detection, limit of quantification, accuracy, precision and robustness. This method was also suitable for the assay determination of desloratadine in pharmaceutical dosage forms.

Insecticide resistance profile of Anopheles gambiae from a phase II field station in Cové, southern Benin: implications for the evaluation of novel vector control products.

PubMed

Ngufor, Corine; N'Guessan, Raphael; Fagbohoun, Josias; Subramaniam, Krishanthi; Odjo, Abibatou; Fongnikin, Augustin; Akogbeto, Martin; Weetman, David; Rowland, Mark

2015-11-18

Novel indoor residual spraying (IRS) and long-lasting insecticidal net (LLIN) products aimed at improving the control of pyrethroid-resistant malaria vectors have to be evaluated in Phase II semi-field experimental studies against highly pyrethroid-resistant mosquitoes. To better understand their performance it is necessary to fully characterize the species composition, resistance status and resistance mechanisms of the vector populations in the experimental hut sites. Bioassays were performed to assess phenotypic insecticide resistance in the malaria vector population at a newly constructed experimental hut site in Cové, a rice growing area in southern Benin, being used for WHOPES Phase II evaluation of newly developed LLIN and IRS products. The efficacy of standard WHOPES-approved pyrethroid LLIN and IRS products was also assessed in the experimental huts. Diagnostic genotyping techniques and microarray studies were performed to investigate the genetic basis of pyrethroid resistance in the Cové Anopheles gambiae population. The vector population at the Cové experimental hut site consisted of a mixture of Anopheles coluzzii and An. gambiae s.s. with the latter occurring at lower frequencies (23 %) and only in samples collected in the dry season. There was a high prevalence of resistance to pyrethroids and DDT (>90 % bioassay survival) with pyrethroid resistance intensity reaching 200-fold compared to the laboratory susceptible An. gambiae Kisumu strain. Standard WHOPES-approved pyrethroid IRS and LLIN products were ineffective in the experimental huts against this vector population (8-29 % mortality). The L1014F allele frequency was 89 %. CYP6P3, a cytochrome P450 validated as an efficient metabolizer of pyrethroids, was over-expressed. Characterizing pyrethroid resistance at Phase II field sites is crucial to the accurate interpretation of the performance of novel vector control products. The strong levels of pyrethroid resistance at the Cové experimental hut station make it a suitable site for Phase II experimental hut evaluations of novel vector control products, which aim for improved efficacy against pyrethroid-resistant malaria vectors to WHOPES standards. The resistance genes identified can be used as markers for further studies investigating the resistance management potential of novel mixture LLIN and IRS products tested at the site.

EARLY ENTRANCE COPRODUCTION PLANT

DOE Office of Scientific and Technical Information (OSTI.GOV)

David Storm; Govanon Nongbri; Steve Decanio

2004-01-12

The overall objective of this project is the three phase development of an Early Entrance Coproduction Plant (EECP) which uses petroleum coke to produce at least one product from at least two of the following three categories: (1) electric power (or heat), (2) fuels, and (3) chemicals using ChevronTexaco's proprietary gasification technology. The objective of Phase I is to determine the feasibility and define the concept for the EECP located at a specific site; develop a Research, Development, and Testing (RD&T) Plan to mitigate technical risks and barriers; and prepare a Preliminary Project Financing Plan. The objective of Phase IImore » is to implement the work as outlined in the Phase I RD&T Plan to enhance the development and commercial acceptance of coproduction technology. The objective of Phase III is to develop an engineering design package and a financing and testing plan for an EECP located at a specific site. The project's intended result is to provide the necessary technical, economic, and environmental information needed by industry to move the EECP forward to detailed design, construction, and operation. The partners in this project are Texaco Energy Systems LLC or TES (a subsidiary of ChevronTexaco), General Electric (GE), Praxair, and Kellogg Brown & Root (KBR) in addition to the U.S. Department of Energy (DOE). TES is providing gasification technology and Fischer-Tropsch (F-T) technology developed by Rentech, Inc., GE is providing combustion turbine technology, Praxair is providing air separation technology, and KBR is providing engineering. During Phase I, a design basis for the Fischer-Tropsch Synthesis section was developed based on limited experience with the specified feed gas and operating conditions. The objective of this Task in Phase II RD&T work was to confirm the performance of the F-T reactor at the set design conditions. Although much of the research, development, and testing work were done by TES outside of this project, several important issues were addressed in this phase of the project. They included Rejuvenation/Regeneration of the Fischer-Tropsch Catalyst, online Catalyst Withdrawal and Addition from the synthesis reactor, and the Fischer-Tropsch Design Basis Confirmation. In Phase III the results from these RD&T work will be incorporated in developing the engineering design package. This Topical Report documents the Phase II RD&T work that was completed for this task.« less

A life cycle assessment of non-renewable energy use and greenhouse gas emissions associated with blueberry and raspberry production in northern Italy.

PubMed

Girgenti, Vincenzo; Peano, Cristiana; Bounous, Michele; Baudino, Claudio

2013-08-01

This study examined the emissions produced during the pre-farm, farm and post-farm phases of the production cycle of raspberries and giant American whortleberries (blueberries) cultivated in one of the best-adapted areas in northern Italy. The pre-farm phase included the greenhouse gas emissions from the production of plants in the nursery and the transportation of the plants to the production farms. The farm phase involved the emissions of greenhouse gases from chemical products, the water used for irrigation, the generation of waste, and the consumption of electricity and other energy. The post-farm phase comprised the transportation of the products to the distribution centre (DC) and their storage in the DC. The use phase is not included in the system, nor is transportation from the supermarket to the home of the final consumer, but the disposal of the packaging is nevertheless taken into account. Indeed, the use of traditional plastic materials during both the field phase (nursery and cultivation) and the post-harvesting phase (packaging) produced the greatest estimated impact. Copyright © 2013 Elsevier B.V. All rights reserved.

ADVANCED WORKER PROTECTION SYSTEM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Judson Hedgehock

2001-03-16

From 1993 to 2000, OSS worked under a cost share contract from the Department of Energy (DOE) to develop an Advanced Worker Protection System (AWPS). The AWPS is a protective ensemble that provides the user with both breathing air and cooling for a NIOSH-rated duration of two hours. The ensemble consists of a liquid air based backpack, a Liquid Cooling Garment (LCG), and an outer protective garment. The AWPS project was divided into two phases. During Phase 1, OSS developed and tested a full-scale prototype AWPS. The testing showed that workers using the AWPS could work twice as long asmore » workers using a standard SCBA. The testing also provided performance data on the AWPS in different environments that was used during Phase 2 to optimize the design. During Phase 1, OSS also performed a life-cycle cost analysis on a representative clean up effort. The analysis indicated that the AWPS could save the DOE millions of dollars on D and D activities and improve the health and safety of their workers. During Phase 2, OSS worked to optimize the AWPS design to increase system reliability, to improve system performance and comfort, and to reduce the backpack weight and manufacturing costs. To support this design effort, OSS developed and tested several different generations of prototype units. Two separate successful evaluations of the ensemble were performed by the International Union of Operation Engineers (IUOE). The results of these evaluations were used to drive the design. During Phase 2, OSS also pursued certifying the AWPS with the applicable government agencies. The initial intent during Phase 2 was to finalize the design and then to certify the system. OSS and Scott Health and Safety Products teamed to optimize the AWPS design and then certify the system with the National Institute of Occupational Health and Safety (NIOSH). Unfortunately, technical and programmatic difficulties prevented us from obtaining NIOSH certification. Despite the inability of NIOSH to certify the design, OSS was able to develop and successfully test, in both the lab and in the field, a prototype AWPS. They clearly demonstrated that a system which provides cooling can significantly increase worker productivity by extending the time they can function in a protective garment. They were also able to develop mature outer garment and LCG designs that provide considerable benefits over current protective equipment, such as self donning and doffing, better visibility, and machine washable. A thorough discussion of the activities performed during Phase 1 and Phase 2 is presented in the AWPS Final Report. The report also describes the current system design, outlines the steps needed to certify the AWPS, discusses the technical and programmatic issues that prevented the system from being certified, and presents conclusions and recommendations based upon the seven year effort.« less

Eicosanoids modulate hyperpnea-induced late phase airway obstruction and hyperreactivity in dogs.

PubMed

Davis, Michael S; McCulloch, Sharron; Myers, Teresa; Freed, Arthur N

2002-01-01

A canine model of exercise-induced asthma was used to test the hypothesis that the development of a late phase response to hyperventilation depends on the acute production of pro-inflammatory mediators. Peripheral airway resistance, reactivity to hypocapnia and aerosol histamine, and bronchoalveolar lavage fluid (BALF) cell and eicosanoid content were measured in dogs approximately 5 h after dry air challenge (DAC). DAC resulted in late phase obstruction, hyperreactivity to histamine, and neutrophilic inflammation. Both cyclooxygenase and lipoxygenase inhibitors administered in separate experiments attenuated the late phase airway obstruction and hyperreactivity to histamine. Neither drug affected the late phase inflammation nor the concentrations of eicosanoids in the BALF obtained 5 h after DAC. This study confirms that hyperventilation of peripheral airways with unconditioned air causes late phase neutrophilia, airway obstruction, and hyperreactivity. The late phase changes in airway mechanics are related to the hyperventilation-induced release of both prostaglandins and leukotrienes, and appear to be independent of the late phase infiltration of inflammatory cells.

Development and approval of vaccines in the United States.

PubMed

Botstein, P

1986-01-01

In the United States, vaccines and the establishments in which they are manufactured are required to be licensed by the Food and Drug Administration (FDA) before the vaccine can be marketed. This licensing process, as well as the development and investigation of vaccines, is regulated by the FDA's Office of Biologics Research and Review. An application for licensing must contain information supporting the safety, effectiveness, purity and potency of the product. These are data obtained during the investigational phase and then submitted by a commercial sponsor for review and approval. Inspections, surveillance and laboratory testing are performed by the FDA before and after issuance of a license for marketing. The procedures and policies in the investigational and licensing phases of vaccine development are described.

[Determination of geniposidic acid and chlorogenic acid in male flowers and related products of Eucommia ulmoides by reversed-phase high performance liquid chromatography].

PubMed

Dong, Juane; Ma, Xihan

2007-03-01

A simple and rapid high performance liquid chromatographic method has been developed for the determination of geniposidic acid and chlorogenic acid in the male flowers and related products of Eucommia ulmoides. Two components were separated by a Shim-pack VP-ODS column (150 mm x4.6 mm, 5 [microm) with a mobile phase of methanol-water-acetic acid (24 :75: 1, v/v) at a flow rate of 1 mL/min, column temperature of 30 93 and detection wavelength of 240 nm. Under the chromatographic conditions mentioned above, the method performance, such as the number of theoretical plate, resolution, trailing etc have all reached required level. The linear ranges were 0. 025 - 0. 400 g/L for geniposidic acid and 0. 075 - 1. 200 g/L for chlorogenic acid, with the correlation coefficients of 0. 999 7 and 0. 999 9, respectively. The average recoveries were 100. 2% and 100. 5%, and the relative standard deviations (RSDs) were 1. 47% and 1. 49% respectively. The minimum detection limits were 0. 02 microg/L for geniposidic acid, and 0. 06 microg/L for chlorogenic acid. The method developed has demonstrated the characteristics of simple mobile phase composition, short retention, good resolution, high repeatability and precision. It is suitable for the determination of the two compounds in the male flowers of E. ulmoides and related products.

Key Largo Limestone revisited: Pleistocene shelf-edge facies, Florida Keys, USA

USGS Publications Warehouse

Gray, Multer H.; Gischler, E.; Lundberg, J.; Simmons, K.R.; Shinn, E.A.

2002-01-01

New dates and analysis of 12 deep and 57 shallow cores allow a more detailed interpretation of the Pleistocene shelf edge of the Florida Platform as found in various facies of the Key Largo Limestone beneath the Florida Keys. In this study a three-phase evolution of the Quaternary units (Q1-Q5) of the Key Largo is presented with new subdivision of the Q5. (1) In the first phase, the Q1 and Q2 (perhaps deposited during oxygen-isotope stage 11) deep-water quartz-rich environment evolved into a shallow carbonate phase. (2) Subsequently, a Q3 (presumably corresponding to oxygen-isotope stage 9) flourishing reef and productive high-platform sediment phase developed. (3) Finally, a Q4 and Q5 (corresponding to oxygen-isotope stages 7 and 5) stabilization phase occured with reefs and leeward productive lagoons, followed by lower sea levels presenting a sequence of younger (isotope substages 5c, 5a) shelf-margin wedges, sediment veneers and outlier reefs. The Key Largo Limestone provides an accessible model of a carbonate shelf edge with fluctuating water depth, bordering a deep seaward basin for a period of at least 300 ka. During this time, at least four onlaps/offlaps, often separated by periods of karst development with associated diagenetic alterations, took place. The story presented by this limestone not only allows a better understanding of the history of south Florida but also aids in the interpretation of similar persistent shelf-edge sites bordering deep basins in other areas.

Modeling quiescent phase transport of air bubbles induced by breaking waves

NASA Astrophysics Data System (ADS)

Shi, Fengyan; Kirby, James T.; Ma, Gangfeng

Simultaneous modeling of both the acoustic phase and quiescent phase of breaking wave-induced air bubbles involves a large range of length scales from microns to meters and time scales from milliseconds to seconds, and thus is computational unaffordable in a surfzone-scale computational domain. In this study, we use an air bubble entrainment formula in a two-fluid model to predict air bubble evolution in the quiescent phase in a breaking wave event. The breaking wave-induced air bubble entrainment is formulated by connecting the shear production at the air-water interface and the bubble number intensity with a certain bubble size spectra observed in laboratory experiments. A two-fluid model is developed based on the partial differential equations of the gas-liquid mixture phase and the continuum bubble phase, which has multiple size bubble groups representing a polydisperse bubble population. An enhanced 2-DV VOF (Volume of Fluid) model with a k - ɛ turbulence closure is used to model the mixture phase. The bubble phase is governed by the advection-diffusion equations of the gas molar concentration and bubble intensity for groups of bubbles with different sizes. The model is used to simulate air bubble plumes measured in laboratory experiments. Numerical results indicate that, with an appropriate parameter in the air entrainment formula, the model is able to predict the main features of bubbly flows as evidenced by reasonable agreement with measured void fraction. Bubbles larger than an intermediate radius of O(1 mm) make a major contribution to void fraction in the near-crest region. Smaller bubbles tend to penetrate deeper and stay longer in the water column, resulting in significant contribution to the cross-sectional area of the bubble cloud. An underprediction of void fraction is found at the beginning of wave breaking when large air pockets take place. The core region of high void fraction predicted by the model is dislocated due to use of the shear production in the algorithm for initial bubble entrainment. The study demonstrates a potential use of an entrainment formula in simulations of air bubble population in a surfzone-scale domain. It also reveals some difficulties in use of the two-fluid model for predicting large air pockets induced by wave breaking, and suggests that it may be necessary to use a gas-liquid two-phase model as the basic model framework for the mixture phase and to develop an algorithm to allow for transfer of discrete air pockets to the continuum bubble phase. A more theoretically justifiable air entrainment formulation should be developed.

Hydrothermal Synthesis of Dicalcium Silicate Based Cement

NASA Astrophysics Data System (ADS)

Dutta, N.; Chatterjee, A.

2017-06-01

It is imperative to develop low energy alternative binders considering the large amounts of energy consumed as well as carbon dioxide emissions involved in the manufacturing of ordinary Portland cement. This study is on the synthesis of a dicalcium silicate based binder using a low temperature hydrothermal route.The process consists of synthesizing an intermediate product consisting of a calcium silicate hydrate phase with a Ca:Si ratio of 2:1 and further thermal treatment to produce the β-Ca2SiO4 (C2S) phase.Effect of various synthesis parameters like water to solid ratio, dwell time and temperature on the formation of the desired calcium silicate hydrate phase is reported along with effect of heating conditions for formation of the β-C2S phase. Around 77.45% of β-C2S phase was synthesized by thermal treatment of the intermediate phase at 820°C.

Site-index curves for young-growth ponderosa pine in northern Arizona

Treesearch

Charles O. Minor

1964-01-01

The productive capacity or site quality of an area enters into nearly every phase of forest management from regeneration to final harvest. No standards or measures of site quality have been developed specifically for ponderosa pine in the Southwest, which handicaps the forest manager. The major objective of the present study was to develop the basic site-index curves...

Pathophysiology of luteal-phase deficiency in human reproduction.

PubMed

Nakajima, S T; Gibson, M

1991-03-01

There are numerous probable mechanisms for the clinical occurrence of a luteal-phase deficiency. Defects may occur in either the proliferative, luteal, or luteal-rescue stage of a menstrual cycle. In each of these three domains, alterations in the trophic stimulation or the response at either the ovarian or endometrial level further subdivide the etiologies for luteal-phase deficiency. Additional development of new concepts in the areas of intraovarian signaling, the possible role of growth factors, and the measurement of newly discovered luteal products will enable us to expand our thought process. With a better understanding of the pathophysiology of luteal-phase deficiency, it is anticipated that new treatments will be devised to address precisely a given specific etiologic factor.

Understanding the Impact of Water on the Miscibility and Microstructure of Amorphous Solid Dispersions: An AFM-LCR and TEM-EDX Study.

PubMed

Li, Na; Gilpin, Christopher J; Taylor, Lynne S

2017-05-01

Miscibility is critical for amorphous solid dispersions (ASDs). Phase-separated ASDs are more prone to crystallization, and thus can lose their solubility advantage leading to product failure. Additionally, dissolution performance can be diminished as a result of phase separation in the ASD matrix. Water is known to induce phase separation during storage for some ASDs. However, the impact of water introduced during preparation has not been as thoroughly investigated to date. The purpose of this study was to develop a mechanistic understanding of the effect of water on the phase behavior and microstructure of ASDs. Evacetrapib and two polymers were selected as the model system. Atomic force microscopy coupled with Lorentz contact resonance, and transmission electron microscopy with energy dispersive X-ray spectroscopy were employed to evaluate the microstructure and composition of phase-separated ASDs. It was found that phase separation could be induced via two routes: solution-state phase separation during ASD formation caused by water absorption during film formation by a hydrophilic solvent, or solid-phase separation following exposure to high RH during storage. Water contents of as low as 2% in the organic solvent system used to dissolve the drug and polymer were found to result in phase separation in the resultant ASD film. These findings have profound implications on lab-scale ASD preparation and potentially also for industrial production. Additionally, these high-resolution imaging techniques combined with orthogonal analyses are powerful tools to visualize structural changes in ASDs, which in turn will enable better links to be made between ASD structure and performance.

Challenges in a product development partnership: a malaria treatment case study.

PubMed

Luiza, Vera Lucia; Chaves, Gabriela Costa; Barboza, Tayná Marques Torres; Gonçalves, Luciana de Paula Barros; Stobbaerts, Eric G

2017-07-01

This paper examines the development of a treatment - a fixed-dose combination of artesunate and mefloquine - in Brazil, from three points of view: in terms of access to medication; to record and report successes; and to look at the lessons learned. This product development took place in the ambit of a public-private partnership. Semi-structured interviews were held with key actors involved in the different phases of the development, and documents were analyzed. Two important points of reference orienting the design of the study and analysis were: a logical model for access to medication; and evaluation of programs. It is concluded that there were several successes over the course of the project, but insufficient attention was given in the project's architecture to planning of adoption of the product: irregularities in demand caused difficulties in planning and production, and adoption of the product was irregular in the Americas. It is concluded that the project can be considered to have been successful: the product was created, and the aims were met - strengthening of institutional and individual capacities and alliances, and advocacy. However, there were weaknesses in the process, which need to be mitigated in future projects of the same type.

A method for tailoring the information content of a software process model

NASA Technical Reports Server (NTRS)

Perkins, Sharon; Arend, Mark B.

1990-01-01

The framework is defined for a general method for selecting a necessary and sufficient subset of a general software life cycle's information products, to support new software development process. Procedures for characterizing problem domains in general and mapping to a tailored set of life cycle processes and products is presented. An overview of the method is shown using the following steps: (1) During the problem concept definition phase, perform standardized interviews and dialogs between developer and user, and between user and customer; (2) Generate a quality needs profile of the software to be developed, based on information gathered in step 1; (3) Translate the quality needs profile into a profile of quality criteria that must be met by the software to satisfy the quality needs; (4) Map the quality criteria to set of accepted processes and products for achieving each criterion; (5) Select the information products which match or support the accepted processes and product of step 4; and (6) Select the design methodology which produces the information products selected in step 5.

A method for tailoring the information content of a software process model

NASA Technical Reports Server (NTRS)

Perkins, Sharon; Arend, Mark B.

1990-01-01

The framework is defined for a general method for selecting a necessary and sufficient subset of a general software life cycle's information products, to support new software development process. Procedures for characterizing problem domains in general and mapping to a tailored set of life cycle processes and products is presented. An overview of the method is shown using the following steps: (1) During the problem concept definition phase, perform standardized interviews and dialogs between developer and user, and between user and customer; (2) Generate a quality needs profile of the software to be developed, based on information gathered in step 1; (3) Translate the quality needs profile into a profile of quality criteria that must be met by the software to satisfy the quality needs; (4) Map the quality criteria to a set of accepted processes and products for achieving each criterion; (5) select the information products which match or support the accepted processes and product of step 4; and (6) Select the design methodology which produces the information products selected in step 5.

[Phase transfer catalyzed bioconversion of penicillin G to 6-APA by immobilized penicillin acylase in recyclable aqueous two-phase systems with light/pH sensitive copolymers].

PubMed

Jin, Ke-ming; Cao, Xue-jun; Su, Jin; Ma, Li; Zhuang, Ying-ping; Chu, Ju; Zhang, Si-liang

2008-03-01

Immobilized penicillin acylase was used for bioconversion of penicillin PG into 6-APA in aqueous two-phase systems consisting of a light-sensitive polymer PNBC and a pH-sensitive polymer PADB. Partition coefficients of 6-APA was found to be about 5.78 in the presence of 1% NaCl. Enzyme kinetics showed that the reaction reached equilibrium at roughly 7 h. The 6-APA mole yields were 85.3% (pH 7.8, 20 degrees C), with about 20% increment as compared with the reaction of single aqueous phase buffer. The partition coefficient of PG (Na) varied scarcely, while that of the product, 6-APA and phenylacetic acid (PA) significantly varied due to Donnan effect of the phase systems and hydrophobicity of the products. The variation of the partition coefficients of the products also affected the bioconversion yield of the products. In the aqueous two-phase systems, the substrate, PG, the products of 6-APA and PA were biased in the top phase, while immobilized penicillin acylase at completely partitioned at the bottom. The substrate and PG entered the bottom phase, where it was catalyzed into 6-APA and PA and entered the top phase. Inhibition of the substrate and products was removed to result in improvement of the product yield, and the immobilized enzyme showed higher efficiency than the immobilized cells and occupied smaller volume. Compared with the free enzyme, immobilized enzyme had greater stability, longer life-time, and was completely partitioned in the bottom phase and recycle. Bioconversion in two-phase systems using immobilized penicillin acylase showed outstanding advantage. The light-sensitive copolymer forming aqueous two-phase systems could be recovered by laser radiation at 488 nm or filtered 450 nm light, while pH-sensitive polymer PADB could be recovered at the isoelectric point (pH 4.1). The recovery of the two copolymers was between 95% and 99%.

Quantitative Evaluation of MDP-Ca Salt and DCPD after Application of an MDP-based One-step Self-etching Adhesive on Enamel and Dentin.

PubMed

Yokota, Yoko; Fujita, Kou Nakajima; Uchida, Ryoichiro; Aida, Etsuko; Aoki, Naoko Tabei; Aida, Masahiro; Nishiyama, Norihiro

To investigate the effects of an experimental 10-methacryloyloxydecyl dihydrogen phosphate (MDP)-based one-step self-etching adhesive (EX adhesive) applied to enamel and dentin on the production of calcium salt of MDP (MDP-Ca salt) and dicalcium phosphate dehydrate (DCPD) at various periods. The EX adhesive was prepared. Bovine enamel and dentin reactants were prepared by varying the application period of the EX adhesive: 0.5, 1, 5, 30, 60 and 1440 min. Enamel and dentin reactants were analyzed using x-ray diffraction and solid-state phosphorus-31 nuclear magnetic resonance (31P NMR). Curvefitting analyses of corresponding 31P NMR spectra were performed. Enamel and dentin developed several types of MDP-Ca salts and DCPDs with amorphous and crystalline phases throughout the application period. The predominant molecular species of MDP-Ca salt was determined as the monocalcium salt of the MDP monomer. Dentin showed a faster production rate and greater produced amounts of MDP-Ca salt than did enamel, since enamel showed a knee-point in the production rate of the MDP-Ca salt at the application period of 5 min. In contrast, enamel developed greater amounts of DCPD than did dentin and two types of DCPDs with different crystalline phases at application periods > 30 min. The amounts of MDP-Ca salt developed during the 30-s application of the EX adhesive on enamel and dentin were 7.3 times and 21.2 times greater than DCPD, respectively. The MDP-based one-step adhesive yielded several types of MDP-Ca salts and DCPD with an amorphous phase during the 30-s application period on enamel and dentin.

Modeling the direct sun component in buildings using matrix algebraic approaches: Methods and validation

DOE PAGES

Lee, Eleanor S.; Geisler-Moroder, David; Ward, Gregory

2017-12-23

Simulation tools that enable annual energy performance analysis of optically-complex fenestration systems have been widely adopted by the building industry for use in building design, code development, and the development of rating and certification programs for commercially-available shading and daylighting products. The tools rely on a three-phase matrix operation to compute solar heat gains, using as input low-resolution bidirectional scattering distribution function (BSDF) data (10–15° angular resolution; BSDF data define the angle-dependent behavior of light-scattering materials and systems). Measurement standards and product libraries for BSDF data are undergoing development to support solar heat gain calculations. Simulation of other metrics suchmore » as discomfort glare, annual solar exposure, and potentially thermal discomfort, however, require algorithms and BSDF input data that more accurately model the spatial distribution of transmitted and reflected irradiance or illuminance from the sun (0.5° resolution). This study describes such algorithms and input data, then validates the tools (i.e., an interpolation tool for measured BSDF data and the five-phase method) through comparisons with ray-tracing simulations and field monitored data from a full-scale testbed. Simulations of daylight-redirecting films, a micro-louvered screen, and venetian blinds using variable resolution, tensor tree BSDF input data derived from interpolated scanning goniophotometer measurements were shown to agree with field monitored data to within 20% for greater than 75% of the measurement period for illuminance-based performance parameters. The three-phase method delivered significantly less accurate results. We discuss the ramifications of these findings on industry and provide recommendations to increase end user awareness of the current limitations of existing software tools and BSDF product libraries.« less

Modeling the direct sun component in buildings using matrix algebraic approaches: Methods and validation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Eleanor S.; Geisler-Moroder, David; Ward, Gregory

Simulation tools that enable annual energy performance analysis of optically-complex fenestration systems have been widely adopted by the building industry for use in building design, code development, and the development of rating and certification programs for commercially-available shading and daylighting products. The tools rely on a three-phase matrix operation to compute solar heat gains, using as input low-resolution bidirectional scattering distribution function (BSDF) data (10–15° angular resolution; BSDF data define the angle-dependent behavior of light-scattering materials and systems). Measurement standards and product libraries for BSDF data are undergoing development to support solar heat gain calculations. Simulation of other metrics suchmore » as discomfort glare, annual solar exposure, and potentially thermal discomfort, however, require algorithms and BSDF input data that more accurately model the spatial distribution of transmitted and reflected irradiance or illuminance from the sun (0.5° resolution). This study describes such algorithms and input data, then validates the tools (i.e., an interpolation tool for measured BSDF data and the five-phase method) through comparisons with ray-tracing simulations and field monitored data from a full-scale testbed. Simulations of daylight-redirecting films, a micro-louvered screen, and venetian blinds using variable resolution, tensor tree BSDF input data derived from interpolated scanning goniophotometer measurements were shown to agree with field monitored data to within 20% for greater than 75% of the measurement period for illuminance-based performance parameters. The three-phase method delivered significantly less accurate results. We discuss the ramifications of these findings on industry and provide recommendations to increase end user awareness of the current limitations of existing software tools and BSDF product libraries.« less

Proposal of a framework for scale-up life cycle inventory: A case of nanofibers for lithium iron phosphate cathode applications.

PubMed

Simon, Bálint; Bachtin, Krystyna; Kiliç, Ali; Amor, Ben; Weil, Marcel

2016-07-01

Environmental assessments are crucial for the management of the environmental impacts of a product in a rapidly developing world. The design phase creates opportunities for acting on the environmental issues of products using life cycle assessment (LCA). However, the LCA is hampered by a lack of information originating from distinct scales along the product or technology value chain. Many studies have been undertaken to handle similar problems, but these studies are case-specific and do not analyze the development options in the initial design phase. Thus, systematic studies are needed to determine the possible scaling. Knowledge from such screening studies would open the door for developing new methods that can tackle a given scaling problem. The present article proposes a scale-up procedure that aims to generate a new life cycle inventory (LCI) on a theoretical industrial scale, based on information from laboratory experiments. Three techniques are described to obtain the new LCI. Investigation of a laboratory-scale procedure is discussed to find similar industrial processes as a benchmark for describing a theoretical large-scale production process. Furthermore, LCA was performed on a model system of nanofiber electrospinning for Li-ion battery cathode applications. The LCA results support material developers in identifying promising development pathways. For example, the present study pointed out the significant impacts of dimethylformamide on suspension preparation and the power requirements of distinct electrospinning subprocesses. Nanofiber-containing battery cells had greater environmental impacts than did the reference cell, although they had better electrochemical performance, such as better wettability of the electrode, improving the electrode's electrosorption capacity, and longer expected lifetime. Furthermore, material and energy recovery throughout the production chain could decrease the environmental impacts by 40% to 70%, making the nanofiber a promising battery cathode. Integr Environ Assess Manag 2016;12:465-477. © 2016 SETAC. © 2016 SETAC.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tao Zhu; Jack A. Walker; J. Liang

Due to increasing oil demand, oil companies are moving into arctic environments and deep-water areas for oil production. In these regions of lower temperatures, wax deposits begin to form when the temperature in the wellbore falls below wax appearance temperature (WAT). This condition leads to reduced production rates and larger pressure drops. Wax problems in production wells are very costly due to production down time for removal of wax. Therefore, it is necessary to develop a solution to wax deposition. In order to develop a solution to wax deposition, it is essential to characterize the crude oil and study phasemore » behavior properties. The main objective of this project was to characterize Alaskan North Slope crude oil and study the phase behavior, which was further used to develop a dynamic wax deposition model. This report summarizes the results of the various experimental studies. The subtasks completed during this study include measurement of density, molecular weight, viscosity, pour point, wax appearance temperature, wax content, rate of wax deposition using cold finger, compositional characterization of crude oil and wax obtained from wax content, gas-oil ratio, and phase behavior experiments including constant composition expansion and differential liberation. Also, included in this report is the development of a thermodynamic model to predict wax precipitation. From the experimental study of wax appearance temperature, it was found that wax can start to precipitate at temperatures as high as 40.6 C. The WAT obtained from cross-polar microscopy and viscometry was compared, and it was discovered that WAT from viscometry is overestimated. From the pour point experiment it was found that crude oil can cease to flow at a temperature of 12 C. From the experimental results of wax content, it is evident that the wax content in Alaskan North Slope crude oil can be as high as 28.57%. The highest gas-oil ratio for a live oil sample was observed to be 619.26 SCF/STB. The bubblepoint pressure for live oil samples varied between 1600 psi and 2100 psi. Wax precipitation is one of the most important phenomena in wax deposition and, hence, needs to be modeled. There are various models present in the literature. Won's model, which considers the wax phase as a non-ideal solution, and Pedersen's model, which considers the wax phase as an ideal solution, were compared. Comparison indicated that Pedersen's model gives better results, but the assumption of wax phase as an ideal solution is not realistic. Hence, Won's model was modified to consider different precipitation characteristics of the various constituents in the hydrocarbon fraction. The results obtained from the modified Won's model were compared with existing models, and it was found that predictions from the modified model are encouraging.« less

Rain rate instrument for deployment at sea, phase 2

NASA Technical Reports Server (NTRS)

Steele, Jimmy W.

1992-01-01

This report describes, in detail, the SBIR Phase 2 contracting effort provided for by NASA Contract Number NAS8-38481 in which a prototype Rain Rate Sensor was developed. FWG Model RP101A is a fully functional rain rate and droplet size analyzing instrument. The RP101A is a fully functional rain rate and droplet size analyzing instrument. The RP101A consists of a fiber optic probe containing a 32-fiber array connected to an electronic signal processor. When interfaced to an IBM compatible personal computer and configured with appropriate software, the RP101A is capable of measuring rain rates and particles ranging in size from around 300 microns up to 6 to 7 millimeters. FWG Associates, Inc. intends to develop a production model from the prototype and continue the effort under NASA's SBIR Phase 3 program.

Quantitative methods for estimating the anisotropy of the strength properties and the phase composition of Mg-Al alloys

NASA Astrophysics Data System (ADS)

Betsofen, S. Ya.; Kolobov, Yu. R.; Volkova, E. F.; Bozhko, S. A.; Voskresenskaya, I. I.

2015-04-01

Quantitative methods have been developed to estimate the anisotropy of the strength properties and to determine the phase composition of Mg-Al alloys. The efficiency of the methods is confirmed for MA5 alloy subjected to severe plastic deformation. It is shown that the Taylor factors calculated for basal slip averaged over all orientations of a polycrystalline aggregate with allowance for texture can be used for a quantitative estimation of the contribution of the texture of semifinished magnesium alloy products to the anisotropy of their strength properties. A technique of determining the composition of a solid solution and the intermetallic phase Al12Mg17 content is developed using the measurement of the lattice parameters of the solid solution and the known dependence of these lattice parameters on the composition.

Copper sludge from printed circuit board production/recycling for ceramic materials: a quantitative analysis of copper transformation and immobilization.

PubMed

Tang, Yuanyuan; Lee, Po-Heng; Shih, Kaimin

2013-08-06

The fast development of electronic industries and stringent requirement of recycling waste electronics have produced a large amount of metal-containing waste sludge. This study developed a waste-to-resource strategy to beneficially use such metal-containing sludge from the production and recycling processes of printed circuit board (PCBs). To observe the metal incorporation mechanisms and phase transformation processes, mixtures of copper industrial waste sludge and kaolinite-based materials (kaolinite and mullite) were fired between 650 and 1250 °C for 3 h. The different copper-hosting phases were identified by powder X-ray diffraction (XRD) in the sintered products, and CuAl2O4 was found to be the predominant hosting phase throughout the reactions, regardless of the strong reduction potential of copper expected at high temperatures. The experimental results indicated that CuAl2O4 was generated more easily and in larger quantities at low-temperature processing when using the kaolinite precursor. Maximum copper transformations reached 86% and 97% for kaolinite and mullite systems, respectively, when sintering at 1000 °C. To monitor the stabilization effect after thermal process, prolonged leaching tests were carried out using acetic acid with an initial pH value of 2.9 to leach the sintered products for 20 days. The results demonstrated the decrease of copper leachability with the formation of CuAl2O4, despite different sintering behavior in kaolinite and mullite systems. This study clearly indicates spinel formation as the most crucial metal stabilization mechanism when sintering copper sludge with aluminosilicate materials, and suggests a promising and reliable technique for reusing metal-containing sludge as ceramic materials.

The ground prototype processor: Level-1 production during Sentinel-2 in-orbit acceptance

NASA Astrophysics Data System (ADS)

Petrucci, B.; Dechoz, C.; Lachérade, S.; L'Helguen, C.; Raynaud, J.-L.; Trémas, T.; Picard, C.; Rolland, A.

2015-10-01

Jointly with the European Commission, the Sentinel-2 earth observation optical mission is developed by the European Space Agency (ESA). Relying on a constellation of satellites put in orbit starting mid-2015, Sentinel-2 will be devoted to the monitoring of land and coastal areas worldwide thanks to an imagery at high revisit (5 days with two satellites), high resolution (10m, 20m and 60m) with large swath (290km), and multi-spectral imagery (13 bands in visible and shortwave infra-red). In this framework, the French Space Agency (CNES: Centre National d'Etudes Spatiales) supports ESA on the activities related to Image Quality, defining the image products and prototyping the processing techniques. Scope of this paper is to present the Ground Prototype Processor (GPP) that will be in charge of Level-1 production during Sentinel-2 In Orbit Acceptance phase. GPP has been developed by a European industrial consortium composed of Advanced Computer Systems (ACS), Magellium and DLR on the basis of CNES technical specification of Sentinel-2 data processing and under the joint management of ESA-ESTEC and CNES. It will assure the generation of the products used for Calibration and Validation activities and it will provide the reference data for Sentinel-2 Payload Data Ground Segment Validation. At first, Sentinel-2 end-users products definition is recalled with the associated radiometric and geometric performances; secondly the methods implemented will be presented with an overview of the Ground Image Processing Parameters that need to be tuned during the In Orbit Acceptance phase to assure the required performance of the products. Finally, the complexity of the processing having been showed, the challenges of the production in terms of data volume and processing time will be highlighted. The first Sentinel-2 Level-1 products are shown.

Evaluation of Selected Chemical Processes for Production of Low-cost Silicon, Phase 3

NASA Technical Reports Server (NTRS)

Blocher, J. M., Jr.; Browning, M. F.

1979-01-01

The construction of the 50 MT Si/year experimental process system development unit was deferred until FY 1980, and the fluidized bed, zinc vaporizer, by-product condenser, and electrolytic cell were combined with auxiliary units, capable of supporting 8-hour batchwise operation, to form the process development unit (PDU), which is scheduled to be in operation by October 1, 1979. The design of the PDU and objectives of its operation are discussed. Experimental program support activities described relate to: (1) a wetted-wall condensor; (2) fluidized-bed modeling; (3) zinc chloride electrolysis; and (4) zinc vaporizer.