49 CFR 236.923 - Task analysis and basic requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Standards for Processor-Based Signal and Train Control Systems § 236.923 Task analysis and basic requirements..., inspection, testing, and operating tasks that must be performed on a railroad's products. This includes the...

49 CFR 236.923 - Task analysis and basic requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Standards for Processor-Based Signal and Train Control Systems § 236.923 Task analysis and basic requirements..., inspection, testing, and operating tasks that must be performed on a railroad's products. This includes the...

49 CFR 236.923 - Task analysis and basic requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Standards for Processor-Based Signal and Train Control Systems § 236.923 Task analysis and basic requirements..., inspection, testing, and operating tasks that must be performed on a railroad's products. This includes the...

Flexible automation of cell culture and tissue engineering tasks.

PubMed

Knoll, Alois; Scherer, Torsten; Poggendorf, Iris; Lütkemeyer, Dirk; Lehmann, Jürgen

2004-01-01

Until now, the predominant use cases of industrial robots have been routine handling tasks in the automotive industry. In biotechnology and tissue engineering, in contrast, only very few tasks have been automated with robots. New developments in robot platform and robot sensor technology, however, make it possible to automate plants that largely depend on human interaction with the production process, e.g., for material and cell culture fluid handling, transportation, operation of equipment, and maintenance. In this paper we present a robot system that lends itself to automating routine tasks in biotechnology but also has the potential to automate other production facilities that are similar in process structure. After motivating the design goals, we describe the system and its operation, illustrate sample runs, and give an assessment of the advantages. We conclude this paper by giving an outlook on possible further developments.

Determination of the Proper Rest Time for a Cyclic Mental Task Using ACT-R Architecture.

PubMed

Atashfeshan, Nooshin; Razavi, Hamideh

2017-03-01

Objective Analysis of the effect of mental fatigue on a cognitive task and determination of the right start time for rest breaks in work environments. Background Mental fatigue has been recognized as one of the most important factors influencing individual performance. Subjective and physiological measures are popular methods for analyzing fatigue, but they are restricted to physical experiments. Computational cognitive models are useful for predicting operator performance and can be used for analyzing fatigue in the design phase, particularly in industrial operations and inspections where cognitive tasks are frequent and the effects of mental fatigue are crucial. Method A cyclic mental task is modeled by the ACT-R architecture, and the effect of mental fatigue on response time and error rate is studied. The task includes visual inspections in a production line or control workstation where an operator has to check products' conformity to specifications. Initially, simulated and experimental results are compared using correlation coefficients and paired t test statistics. After validation of the model, the effects are studied by human and simulated results, which are obtained by running 50-minute tests. Results It is revealed that during the last 20 minutes of the tests, the response time increased by 20%, and during the last 12.5 minutes, the error rate increased by 7% on average. Conclusion The proper start time for the rest period can be identified by setting a limit on the error rate or response time. Application The proposed model can be applied early in production planning to decrease the negative effects of mental fatigue by predicting the operator performance. It can also be used for determining the rest breaks in the design phase without an operator in the loop.

Implementing asyncronous collective operations in a multi-node processing system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Dong; Eisley, Noel A.; Heidelberger, Philip

A method, system, and computer program product are disclosed for implementing an asynchronous collective operation in a multi-node data processing system. In one embodiment, the method comprises sending data to a plurality of nodes in the data processing system, broadcasting a remote get to the plurality of nodes, and using this remote get to implement asynchronous collective operations on the data by the plurality of nodes. In one embodiment, each of the nodes performs only one task in the asynchronous operations, and each nodes sets up a base address table with an entry for a base address of a memorymore » buffer associated with said each node. In another embodiment, each of the nodes performs a plurality of tasks in said collective operations, and each task of each node sets up a base address table with an entry for a base address of a memory buffer associated with the task.« less

Within and between Individual Variability of Exposure to Work-Related Musculoskeletal Disorder Risk Factors.

PubMed

Zare, Mohsen; Sagot, Jean-Claude; Roquelaure, Yves

2018-05-17

Industrial companies indicate a tendency to eliminate variations in operator strategies, particularly following implementation of the lean principle. Companies believe when the operators perform the same prescribed tasks, they have to execute them in the same manner (completing the same gestures and being exposed to the same risk factors). They attempt to achieve better product quality by standardizing and reducing operational leeway. However, operators adjust and modify ways of performing tasks to balance between their abilities and the requirements of the job. This study aims to investigate the variability of exposure to physical risk factors within and between operators when executing the same prescribed tasks. The Ergonomic Standard method was used to evaluate two workstations. Seven operators were observed thirty times between repeated cycle times at those workstations. The results revealed the variability of exposure to risk factors between and within operators in the repeated execution of the same tasks. Individual characteristics and operators' strategies might generate the variability of exposure to risk factors that may be an opportunity to reduce the risks of work-related musculoskeletal disorders (WR-MSDs). However, sometimes operators' strategies may cause overexposure to risk factors; operators most often adopt such strategies to undertake their tasks while reducing the workload.

Behavioral Economic Laboratory Research in Tobacco Regulatory Science.

PubMed

Tidey, Jennifer W; Cassidy, Rachel N; Miller, Mollie E; Smith, Tracy T

2016-10-01

Research that can provide a scientific foundation for the United States Food and Drug Administration (FDA) tobacco policy decisions is needed to inform tobacco regulatory policy. One factor that affects the impact of a tobacco product on public health is its intensity of use, which is determined, in part, by its abuse liability or reinforcing efficacy. Behavioral economic tasks have considerable utility for assessing the reinforcing efficacy of current and emerging tobacco products. This paper provides a narrative review of several behavioral economic laboratory tasks and identifies important applications to tobacco regulatory science. Behavioral economic laboratory assessments, including operant self-administration, choice tasks and purchase tasks, can be used generate behavioral economic data on the effect of price and other constraints on tobacco product consumption. These tasks could provide an expedited simulation of the effects of various tobacco control policies across populations of interest to the FDA. Tobacco regulatory research questions that can be addressed with behavioral economic tasks include assessments of the impact of product characteristics on product demand, assessments of the abuse liability of novel and potential modified risk tobacco products (MRTPs), and assessments of the impact of conventional and novel products in vulnerable populations.

Development of a Space Station Operations Management System

NASA Technical Reports Server (NTRS)

Brandli, A. E.; Mccandless, W. T.

1988-01-01

To enhance the productivity of operations aboard the Space Station, a means must be provided to augment, and frequently to supplant, human effort in support of mission operations and management, both on the ground and onboard. The Operations Management System (OMS), under development at the Johnson Space Center, is one such means. OMS comprises the tools and procedures to facilitate automation of station monitoring, control, and mission planning tasks. OMS mechanizes, and hence rationalizes, execution of tasks traditionally performed by mission planners, the mission control center team, onboard System Management software, and the flight crew.

Development of a Space Station Operations Management System

NASA Astrophysics Data System (ADS)

Brandli, A. E.; McCandless, W. T.

To enhance the productivity of operations aboard the Space Station, a means must be provided to augment, and frequently to supplant, human effort in support of mission operations and management, both on the ground and onboard. The Operations Management System (OMS), under development at the Johnson Space Center, is one such means. OMS comprises the tools and procedures to facilitate automation of station monitoring, control, and mission planning tasks. OMS mechanizes, and hence rationalizes, execution of tasks traditionally performed by mission planners, the mission control center team, onboard System Management software, and the flight crew.

Space Mission Operations Concept

NASA Technical Reports Server (NTRS)

Squibb, Gael F.

1996-01-01

This paper will discuss the concept of developing a space mission operations concept; the benefits of starting this system engineering task early; the neccessary inputs to the process; and the products that are generated.

Time estimation as a secondary task to measure workload. [attention sharing effect on operator performance

NASA Technical Reports Server (NTRS)

Hart, S. G.

1975-01-01

Variation in the length of time productions and verbal estimates of duration was investigated to determine the influence of concurrent activity on operator time perception. The length of 10-, 20-, and 30-sec intervals produced while performing six different compensatory tracking tasks was significantly longer, 23% on the average, than those produced while performing no other task. Verbal estimates of session duration, taken at the end of each of 27 experimental sessions, reflected a parallel increase in subjective underestimation of the passage of time as the difficulty of the task performed increased. These data suggest that estimates of duration made while performing a manual control task provide stable and sensitive measures of the workload imposed by the primary task, with minimal interference.

Space shuttle operations integration plan

NASA Technical Reports Server (NTRS)

1975-01-01

The Operations Integration Plan is presented, which is to provide functional definition of the activities necessary to develop and integrate shuttle operating plans and facilities to support flight, flight control, and operations. It identifies the major tasks, the organizations responsible, their interrelationships, the sequence of activities and interfaces, and the resultant products related to operations integration.

Autonomous Sensorweb Operations for Integrated Space, In-Situ Monitoring of Volcanic Activity

NASA Technical Reports Server (NTRS)

Chien, Steve A.; Doubleday, Joshua; Kedar, Sharon; Davies, Ashley G.; Lahusen, Richard; Song, Wenzhan; Shirazi, Behrooz; Mandl, Daniel; Frye, Stuart

2010-01-01

We have deployed and demonstrated operations of an integrated space in-situ sensorweb for monitoring volcanic activity. This sensorweb includes a network of ground sensors deployed to the Mount Saint Helens volcano as well as the Earth Observing One spacecraft. The ground operations and space operations are interlinked in that ground-based intelligent event detections can cause the space segment to acquire additional data via observation requests and space-based data acquisitions (thermal imagery) can trigger reconfigurations of the ground network to allocate increased bandwidth to areas of the network best situated to observe the activity. The space-based operations are enabled by an automated mission planning and tasking capability which utilizes several Opengeospatial Consortium (OGC) Sensorweb Enablement (SWE) standards which enable acquiring data, alerts, and tasking using web services. The ground-based segment also supports similar protocols to enable seamless tasking and data delivery. The space-based segment also supports onboard development of data products (thermal summary images indicating areas of activity, quicklook context images, and thermal activity alerts). These onboard developed products have reduced data volume (compared to the complete images) which enables them to be transmitted to the ground more rapidly in engineering channels.

Lower cost offshore field development utilizing autonomous vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frisbie, F.R.; Vie, K.J.; Welch, D.W.

1996-12-31

The offshore oil and gas industry has the requirement to inspect offshore oil and gas pipelines for scour, corrosion and damage as well as inspect and intervene on satellite production facilities. This task is currently performed with Remotely Operated Vehicles (ROV) operated from dynamically positioned (DP) offshore supply or diving support boats. Currently, these tasks are expensive due to the high day rates for DP ships and the slow, umbilical impeded, 1 knot inspection rates of the tethered ROVs, Emerging Autonomous Undersea Vehicle (AUV) technologies offer opportunities to perform these same inspection tasks for 50--75% lower cost, with comparable ormore » improved quality. The new generation LAPV (Linked Autonomous Power Vehicles) will operate from fixed facilities such as TLPs or FPFs and cover an operating field 10 kms in diameter.« less

Algorithm for decision support as the tool for control system of industries with variable assortment of products

NASA Astrophysics Data System (ADS)

Ladaniuk, Anatolii; Ivashchuk, Viacheslav; Kisała, Piotr; Askarova, Nursanat; Sagymbekova, Azhar

2015-12-01

Conditions of diversification of enterprise products are involving for changes of higher levels of management hierarchy, so it's leading by tasks correcting and changing schedule for operating of production plans. Ordinary solve by combination of enterprise resource are planning and management execution system often has exclusively statistical content. So, the development of decision support system, that helps to use knowledge about subject for capabilities estimating and order of operation of production object is relevant in this time.

Psychological Operations: Fighting the War of Ideas

DTIC Science & Technology

2007-05-18

is the success of the Joint Interagency Task Force on the Former Regime Elements (JIATF- FRE) operation to capture Fadhil Ibrahim Habib al-Mashadani... DAPS ), Fly Away Broadcast System (FABS), and Target Audience Analysis Detachment (TAAD). This provides the Brigade a radio development and broadcast...level. Production and dissemination assets must include a Modular Print System (MPS), Deployable Audio Production Suite ( DAPS ), and Special

[Changes in the forms of industrial production and their effects on workers' health].

PubMed

Fernandes, Rita de Cássia Pereira; Assunção, Ada Avila; Carvalho, Fernando Martins

2010-06-01

This study aimed to identify determinants of health in workers of plastic industries. Production organization, machinery from maintenance and productive areas, and workers' characteristics of 14 plastic industries from Greater Salvador, Bahia State, Brazil, were described. Data were collected about development policy of each company; marketing, operational procedures; production and quality requirements, and formal rules of work organization. High strain management techniques for production time reduction have been implemented. The increase of work rhythm, reduction of break time, and a situation of high cognitive demand impose to workers anomalous body positioning for performing tasks that imply repetitive movements. Physical and psychosocial demands (repetitive work, lower control of the worker on his own tasks, time pressure and job dissatisfaction) compose a complex of conditions adverse to workers' health. Changes in production management, personnel and business impose new strains into the development of task by the workers and bringing in new risk factors to workers' health.

Neural Network Classifies Teleoperation Data

NASA Technical Reports Server (NTRS)

Fiorini, Paolo; Giancaspro, Antonio; Losito, Sergio; Pasquariello, Guido

1994-01-01

Prototype artificial neural network, implemented in software, identifies phases of telemanipulator tasks in real time by analyzing feedback signals from force sensors on manipulator hand. Prototype is early, subsystem-level product of continuing effort to develop automated system that assists in training and supervising human control operator: provides symbolic feedback (e.g., warnings of impending collisions or evaluations of performance) to operator in real time during successive executions of same task. Also simplifies transition between teleoperation and autonomous modes of telerobotic system.

Task Decomposition Model for Dispatchers in Dynamic Scheduling of Demand Responsive Transit Systems

DOT National Transportation Integrated Search

2000-06-01

Since the passage of ADA, the demand for paratransit service is steadily increasing. Paratransit companies are relying on computer automation to streamline dispatch operations, increase productivity and reduce operator stress and error. Little resear...

Size effects on the touchpad, touchscreen, and keyboard tasks of netbooks.

PubMed

Lai, Chih-Chun; Wu, Chih-Fu

2012-10-01

The size of a netbook plays an important role in its success. Somehow, the viewing area on screen and ability to type fast were traded off for portability. To further investigate, this study compared the performances of different-sized touchpads, touchscreens, and keyboards of four-sized netbooks for five application tasks. Consequently, the 7" netbook was significantly slower than larger netbooks in all the tasks except the 8.9" netbook touchpad (successive selecting and clicking) or keyboard tasks. Differences were non-significant for the operating times among the 8.9", 10.1", and 11.6" netbooks in all the tasks except between the 8.9" and 11.6" netbooks in keyboards tasks. For error rates, device-type effects rather than size effects were significant. Gender effects were not significant for operating times in all the tasks but for error rates in touchscreen (multi-direction touching) and keyboard tasks. Considering size effects, the 10.1" netbooks seemed to optimally balance between portability and productivity.

Combined analysis of job and task benzene air exposures among workers at four US refinery operations

PubMed Central

Shin, Jennifer (Mi); Unice, Ken M; Gaffney, Shannon H; Kreider, Marisa L; Gelatt, Richard H; Panko, Julie M

2016-01-01

Workplace air samples analyzed for benzene at four US refineries from 1976 to 2007 were pooled into a single dataset to characterize similarities and differences between job titles, tasks and refineries, and to provide a robust dataset for exposure reconstruction. Approximately 12,000 non-task (>180 min) personal samples associated with 50 job titles and 4000 task (<180 min) samples characterizing 24 tasks were evaluated. Personal air sample data from four individual refineries were pooled based on a number of factors including (1) the consistent sampling approach used by refinery industrial hygienists over time, (2) the use of similar exposure controls, (3) the comparability of benzene content of process streams and end products, (4) the ability to assign uniform job titles and task codes across all four refineries, and (5) our analysis of variance (ANOVA) of the distribution of benzene air concentrations for select jobs/tasks across all four refineries. The jobs and tasks most frequently sampled included those with highest potential contact with refinery product streams containing benzene, which reflected the targeted sampling approach utilized by the facility industrial hygienists. Task and non-task data were analyzed to identify and account for significant differences within job-area, task-job, and task-area categories. This analysis demonstrated that in general, areas with benzene containing process streams were associated with greater benzene air concentrations compared to areas with process streams containing little to no benzene. For several job titles and tasks analyzed, there was a statistically significant decrease in benzene air concentration after 1990. This study provides a job and task-focused analysis of occupational exposure to benzene during refinery operations, and it should be useful for reconstructing refinery workers’ exposures to benzene over the past 30 years. PMID:26862134

Combined analysis of job and task benzene air exposures among workers at four US refinery operations.

PubMed

Burns, Amanda; Shin, Jennifer Mi; Unice, Ken M; Gaffney, Shannon H; Kreider, Marisa L; Gelatt, Richard H; Panko, Julie M

2017-03-01

Workplace air samples analyzed for benzene at four US refineries from 1976 to 2007 were pooled into a single dataset to characterize similarities and differences between job titles, tasks and refineries, and to provide a robust dataset for exposure reconstruction. Approximately 12,000 non-task (>180 min) personal samples associated with 50 job titles and 4000 task (<180 min) samples characterizing 24 tasks were evaluated. Personal air sample data from four individual refineries were pooled based on a number of factors including (1) the consistent sampling approach used by refinery industrial hygienists over time, (2) the use of similar exposure controls, (3) the comparability of benzene content of process streams and end products, (4) the ability to assign uniform job titles and task codes across all four refineries, and (5) our analysis of variance (ANOVA) of the distribution of benzene air concentrations for select jobs/tasks across all four refineries. The jobs and tasks most frequently sampled included those with highest potential contact with refinery product streams containing benzene, which reflected the targeted sampling approach utilized by the facility industrial hygienists. Task and non-task data were analyzed to identify and account for significant differences within job-area, task-job, and task-area categories. This analysis demonstrated that in general, areas with benzene containing process streams were associated with greater benzene air concentrations compared to areas with process streams containing little to no benzene. For several job titles and tasks analyzed, there was a statistically significant decrease in benzene air concentration after 1990. This study provides a job and task-focused analysis of occupational exposure to benzene during refinery operations, and it should be useful for reconstructing refinery workers' exposures to benzene over the past 30 years.

Construction operations for an early lunar base

NASA Technical Reports Server (NTRS)

Graf, John

1988-01-01

Six construction tasks identified as activities likely to be performed at an early lunar base are described: initializing the habitation module, preparing a landing site, transferring payload off the lander, smoothing roads, constructing the inflatable structure, and excavating for lunar oxygen production. Requirements for each task are given, and a point design capable of meeting the task requirements is described. EVA needs are listed for each task. The equipment used to perform these tasks is described. It is noted that all the tasks can be performed with three common vehicles (a rover, a truck, and an excavator) and some shared equipment.

Time and motion studies of National Health Service cataract theatre lists to determine strategies to improve efficiency.

PubMed

Roberts, Harry W; Myerscough, James; Borsci, Simone; Ni, Melody; O'Brart, David P S

2017-11-24

To provide a quantitative assessment of cataract theatre lists focusing on productivity and staffing levels/tasks using time and motion studies. National Health Service (NHS) cataract theatre lists were prospectively observed in five different institutions (four NHS hospitals and one private hospital). Individual tasks and their timings of every member of staff were recorded. Multiple linear regression analyses were performed to investigate possible associations between individual timings and tasks. 140 operations were studied over 18 theatre sessions. The median number of scheduled cataract operations was 7 (range: 5-14). The average duration of an operation was 10.3 min±(SD 4.11 min). The average time to complete one case including patient turnaround was 19.97 min (SD 8.77 min). The proportion of the surgeons' time occupied on total duties or operating ranged from 65.2% to 76.1% and from 42.4% to 56.7%, respectively. The correlations of the surgical time to patient time in theatre was R 2 =0.95. A multiple linear regression model found a significant association (F(3,111)=32.86, P<0.001) with R 2 =0.47 between the duration of one operation and the number of allied healthcare professionals (AHPs), the number of AHP key tasks and the time taken to perform these key tasks by the AHPs. Significant variability in the number of cases performed and the efficiency of patient flow were found between different institutions. Time and motion studies identified requirements for high-volume models and factors relating to performance. Supporting the surgeon with sufficient AHPs and tasks performed by AHPs could improve surgical efficiency up to approximately double productivity over conventional theatre models. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Concept of Operations for the ESC Product Line Approach.

DTIC Science & Technology

1996-08-30

production of the application. Product Line Engineering Center ( PLEC ) defines and evolves product line architectures with the SAG. The PLEC is also tasked... PLEC , SAG, and PLAS and offers scenarios for asset and system development. • Section 4 outlines the ESC Product Line transition strategy. • Section...Line or System Needs User Select PLEC ; Assess PL architecture Product Line Architecture Development ments; architecture selection Architecture

EVA-SCRAM operations

NASA Technical Reports Server (NTRS)

Flanigan, Lee A.; Tamir, David; Weeks, Jack L.; Mcclure, Sidney R.; Kimbrough, Andrew G.

1994-01-01

This paper wrestles with the on-orbit operational challenges introduced by the proposed Space Construction, Repair, and Maintenance (SCRAM) tool kit for Extra-Vehicular Activity (EVA). SCRAM undertakes a new challenging series of on-orbit tasks in support of the near-term Hubble Space Telescope, Extended Duration Orbiter, Long Duration Orbiter, Space Station Freedom, other orbital platforms, and even the future manned Lunar/Mars missions. These new EVA tasks involve welding, brazing, cutting, coating, heat-treating, and cleaning operations. Anticipated near-term EVA-SCRAM applications include construction of fluid lines and structural members, repair of punctures by orbital debris, refurbishment of surfaces eroded by atomic oxygen, and cleaning of optical, solar panel, and high emissivity radiator surfaces which have been degraded by contaminants. Future EVA-SCRAM applications are also examined, involving mass production tasks automated with robotics and artificial intelligence, for construction of large truss, aerobrake, and reactor shadow shield structures. Realistically achieving EVA-SCRAM is examined by addressing manual, teleoperated, semi-automated, and fully-automated operation modes. The operational challenges posed by EVA-SCRAM tasks are reviewed with respect to capabilities of existing and upcoming EVA systems, such as the Extravehicular Mobility Unit, the Shuttle Remote Manipulating System, the Dexterous End Effector, and the Servicing Aid Tool.

Information Assurance Tasks Supporting the Processing of Electronic Records Archives

DTIC Science & Technology

2007-03-01

3 Table 2. OpenVPN evaluation results...........................................................................................10 iv 1...operation of necessary security features and compare the network performance under OpenVPN (openvpn.net) operation with the network performance under no...VPN operation (non-VPN) in a gigabit network environment. The reason for selecting OpenVPN product was based on the previous findings of Khanvilkar

Recent Weather Technologies Delivered to America's Space Program by the Applied Meteorology Unit

NASA Technical Reports Server (NTRS)

Bauman, WIlliam, H., III; Crawford, Winifred

2009-01-01

The Applied Meteorology Unit (AMU) is a unique joint venture of NASA, the Air Force and the National Weather Service (NWS) and has been supporting the Space Program for nearly two decades. The AMU acts as a bridge between the meteorological research community and operational forecasters by developing, evaluating and transitioning new technology and techniques to improve weather support to spaceport operations at the Eastern Range (ER) and Kennedy Space Center. Its primary customers are the 45th Weather Squadron at Cape Canaveral Air Force Station (CCAFS), the Spaceflight Meteorology Group at Johnson Space Center and the National Weather Service Office in Melbourne, FL. Its products are used to support NASA's Shuttle and ELV programs as well as Department of Defense and commercial launches from the ER. Shuttle support includes landing sites beyond the ER. The AMU is co-located with the Air Force operational forecasters at CCAFS to facilitate continuous two-way interaction between the AMU and its operational customers. It is operated under a NASA, Air Force, and NWS Memorandum of Understanding (MOU) by a competitively-selected contractor. The contract, which is funded and managed by NASA, provides five full time professionals with degrees in meteorology or related fields, some of whom also have operational experience. NASA provides a Ph.D.- level NASA civil service scientist as Chief of the AMU. The AMU is tasked by its customers through a unique, nationally recognized process. The tasks are limited to development, evaluation and operational transition of technology to improve weather support to spaceport operations and providing expert advice to the customers. The MOU expressly forbids using the AMU resources to conduct operations or do basic research. The presentation will provide a brief overview of the AMU and how it is tasked by its customers to provide high priority products and services. The balance of the presentation will cover a sampling of products delivered over the last 18 years that are currently in operational use. Each example will describe the problem to be solved, the solution provided, and the operational benefits of implementing that solution.

Payload crew activity planning integration. Task 2: Inflight operations and training for payloads

NASA Technical Reports Server (NTRS)

Hitz, F. R.

1976-01-01

The primary objectives of the Payload Crew Activity Planning Integration task were to: (1) Determine feasible, cost-effective payload crew activity planning integration methods. (2) Develop an implementation plan and guidelines for payload crew activity plan (CAP) integration between the JSC Orbiter planners and the Payload Centers. Subtask objectives and study activities were defined as: (1) Determine Crew Activity Planning Interfaces. (2) Determine Crew Activity Plan Type and Content. (3) Evaluate Automated Scheduling Tools. (4) Develop a draft Implementation Plan for Crew Activity Planning Integration. The basic guidelines were to develop a plan applicable to the Shuttle operations timeframe, utilize existing center resources and expertise as much as possible, and minimize unnecessary data exchange not directly productive in the development of the end-product timelines.

Development of Cross-Platform Software for Well Logging Data Visualization

NASA Astrophysics Data System (ADS)

Akhmadulin, R. K.; Miraev, A. I.

2017-07-01

Well logging data processing is one of the main sources of information in the oil-gas field analysis and is of great importance in the process of its development and operation. Therefore, it is important to have the software which would accurately and clearly provide the user with processed data in the form of well logs. In this work, there have been developed a software product which not only has the basic functionality for this task (loading data from .las files, well log curves display, etc.), but can be run in different operating systems and on different devices. In the article a subject field analysis and task formulation have been performed, and the software design stage has been considered. At the end of the work the resulting software product interface has been described.

Spatio-temporal Dynamics of Referential and Inferential Naming: Different Brain and Cognitive Operations to Lexical Selection.

PubMed

Fargier, Raphaël; Laganaro, Marina

2017-03-01

Picture naming tasks are largely used to elicit the production of specific words and sentences in psycholinguistic and neuroimaging research. However, the generation of lexical concepts from a visual input is clearly not the exclusive way speech production is triggered. In inferential speech encoding, the concept is not provided from a visual input, but is elaborated though semantic and/or episodic associations. It is therefore likely that the cognitive operations leading to lexical selection and word encoding are different in inferential and referential expressive language. In particular, in picture naming lexical selection might ensue from a simple association between a perceptual visual representation and a word with minimal semantic processes, whereas richer semantic associations are involved in lexical retrieval in inferential situations. Here we address this hypothesis by analyzing ERP correlates during word production in a referential and an inferential task. The participants produced the same words elicited from pictures or from short written definitions. The two tasks displayed similar electrophysiological patterns only in the time-period preceding the verbal response. In the stimulus-locked ERPs waveform amplitudes and periods of stable global electrophysiological patterns differed across tasks after the P100 component and until 400-500 ms, suggesting the involvement of different, task-specific neural networks. Based on the analysis of the time-windows affected by specific semantic and lexical variables in each task, we conclude that lexical selection is underpinned by a different set of conceptual and brain processes, with semantic processes clearly preceding word retrieval in naming from definition whereas the semantic information is enriched in parallel with word retrieval in picture naming.

It's Time to Transition to Production, Now What?

NASA Technical Reports Server (NTRS)

Jansma, P. A.; Montgomery, Marc; Werntz, David; Payne, Michael

1999-01-01

When it's time to transition to production, it's easy to be too focused on the application itself and to overlook some areas crucial to your success. Learn about the 10 transition tasks that will ensure a smooth transition, and will prepare your organization to operate and use your system effectively.

Exploring the Relationship of Task Performance and Physical and Cognitive Fatigue During a Daylong Light Precision Task.

PubMed

Yung, Marcus; Manji, Rahim; Wells, Richard P

2017-11-01

Our aim was to explore the relationship between fatigue and operation system performance during a simulated light precision task over an 8-hr period using a battery of physical (central and peripheral) and cognitive measures. Fatigue may play an important role in the relationship between poor ergonomics and deficits in quality and productivity. However, well-controlled laboratory studies in this area have several limitations, including the lack of work relevance of fatigue exposures and lack of both physical and cognitive measures. There remains a need to understand the relationship between physical and cognitive fatigue and task performance at exposure levels relevant to realistic production or light precision work. Errors and fatigue measures were tracked over the course of a micropipetting task. Fatigue responses from 10 measures and errors in pipetting technique, precision, and targeting were submitted to principal component analysis to descriptively analyze features and patterns. Fatigue responses and error rates contributed to three principal components (PCs), accounting for 50.9% of total variance. Fatigue responses grouped within the three PCs reflected central and peripheral upper extremity fatigue, postural sway, and changes in oculomotor behavior. In an 8-hr light precision task, error rates shared similar patterns to both physical and cognitive fatigue responses, and/or increases in arousal level. The findings provide insight toward the relationship between fatigue and operation system performance (e.g., errors). This study contributes to a body of literature documenting task errors and fatigue, reflecting physical (both central and peripheral) and cognitive processes.

International Space Station Increment Operations Services

NASA Astrophysics Data System (ADS)

Michaelis, Horst; Sielaff, Christian

2002-01-01

The Industrial Operator (IO) has defined End-to-End services to perform efficiently all required operations tasks for the Manned Space Program (MSP) as agreed during the Ministerial Council in Edinburgh in November 2001. Those services are the result of a detailed task analysis based on the operations processes as derived from the Space Station Program Implementation Plans (SPIP) and defined in the Operations Processes Documents (OPD). These services are related to ISS Increment Operations and ATV Mission Operations. Each of these End-to-End services is typically characterised by the following properties: It has a clearly defined starting point, where all requirements on the end-product are fixed and associated performance metrics of the customer are well defined. It has a clearly defined ending point, when the product or service is delivered to the customer and accepted by him, according to the performance metrics defined at the start point. The implementation of the process might be restricted by external boundary conditions and constraints mutually agreed with the customer. As far as those are respected the IO has the free choice to select methods and means of implementation. The ISS Increment Operations Service (IOS) activities required for the MSP Exploitation program cover the complete increment specific cycle starting with the support to strategic planning and ending with the post increment evaluation. These activities are divided into sub-services including the following tasks: - ISS Planning Support covering the support to strategic and tactical planning up to the generation - Development &Payload Integration Support - ISS Increment Preparation - ISS Increment Execution These processes are tight together by the Increment Integration Management, which provides the planning and scheduling of all activities as well as the technical management of the overall process . The paper describes the entire End-to-End ISS Increment Operations service and the implementation to support the Columbus Flight 1E related increment and subsequent ISS increments. Special attention is paid to the implications caused by long term operations on hardware, software and operations personnel.

Framework for Integrating Science Data Processing Algorithms Into Process Control Systems

NASA Technical Reports Server (NTRS)

Mattmann, Chris A.; Crichton, Daniel J.; Chang, Albert Y.; Foster, Brian M.; Freeborn, Dana J.; Woollard, David M.; Ramirez, Paul M.

2011-01-01

A software framework called PCS Task Wrapper is responsible for standardizing the setup, process initiation, execution, and file management tasks surrounding the execution of science data algorithms, which are referred to by NASA as Product Generation Executives (PGEs). PGEs codify a scientific algorithm, some step in the overall scientific process involved in a mission science workflow. The PCS Task Wrapper provides a stable operating environment to the underlying PGE during its execution lifecycle. If the PGE requires a file, or metadata regarding the file, the PCS Task Wrapper is responsible for delivering that information to the PGE in a manner that meets its requirements. If the PGE requires knowledge of upstream or downstream PGEs in a sequence of executions, that information is also made available. Finally, if information regarding disk space, or node information such as CPU availability, etc., is required, the PCS Task Wrapper provides this information to the underlying PGE. After this information is collected, the PGE is executed, and its output Product file and Metadata generation is managed via the PCS Task Wrapper framework. The innovation is responsible for marshalling output Products and Metadata back to a PCS File Management component for use in downstream data processing and pedigree. In support of this, the PCS Task Wrapper leverages the PCS Crawler Framework to ingest (during pipeline processing) the output Product files and Metadata produced by the PGE. The architectural components of the PCS Task Wrapper framework include PGE Task Instance, PGE Config File Builder, Config File Property Adder, Science PGE Config File Writer, and PCS Met file Writer. This innovative framework is really the unifying bridge between the execution of a step in the overall processing pipeline, and the available PCS component services as well as the information that they collectively manage.

Undersea applications of dexterous robotics

NASA Technical Reports Server (NTRS)

Gittleman, Mark M.

1994-01-01

The revolution and application of dexterous robotics in the undersea energy production industry and how this mature technology has affected planned SSF dexterous robotic tasks are examined. Undersea telerobotics, or Remotely Operated Vehicles (ROV's), have evolved in design and use since the mid-1970s. Originally developed to replace commercial divers for both planned and unplanned tasks, they are now most commonly used to perform planned robotic tasks in all phases of assembly, inspection, and maintenance of undersea structures and installations. To accomplish these tasks, the worksites, the tasks themselves, and the tools are now engineered with both the telerobot's and the diver's capabilities in mind. In many cases, this planning has permitted a reduction in telerobot system complexity and cost. The philosophies and design practices that have resulted in the successful incorporation of telerobotics into the highly competitive and cost conscious offshore production industry have been largely ignored in the space community. Cases where these philosophies have been adopted or may be successfully adopted in the near future are explored.

Automated power management and control

NASA Technical Reports Server (NTRS)

Dolce, James L.

1991-01-01

A comprehensive automation design is being developed for Space Station Freedom's electric power system. A joint effort between NASA's Office of Aeronautics and Exploration Technology and NASA's Office of Space Station Freedom, it strives to increase station productivity by applying expert systems and conventional algorithms to automate power system operation. The initial station operation will use ground-based dispatches to perform the necessary command and control tasks. These tasks constitute planning and decision-making activities that strive to eliminate unplanned outages. We perceive an opportunity to help these dispatchers make fast and consistent on-line decisions by automating three key tasks: failure detection and diagnosis, resource scheduling, and security analysis. Expert systems will be used for the diagnostics and for the security analysis; conventional algorithms will be used for the resource scheduling.

Analysis of methods of processing of expert information by optimization of administrative decisions

NASA Astrophysics Data System (ADS)

Churakov, D. Y.; Tsarkova, E. G.; Marchenko, N. D.; Grechishnikov, E. V.

2018-03-01

In the real operation the measure definition methodology in case of expert estimation of quality and reliability of application-oriented software products is offered. In operation methods of aggregation of expert estimates on the example of a collective choice of an instrumental control projects in case of software development of a special purpose for needs of institutions are described. Results of operation of dialogue decision making support system are given an algorithm of the decision of the task of a choice on the basis of a method of the analysis of hierarchies and also. The developed algorithm can be applied by development of expert systems to the solution of a wide class of the tasks anyway connected to a multicriteria choice.

Health effects of gasoline exposure. I. Exposure assessment for U.S. distribution workers.

PubMed Central

Smith, T J; Hammond, S K; Wong, O

1993-01-01

Personal exposures were estimated for a large cohort of workers in the U.S. domestic system for distributing gasoline by trucks and marine vessels. This assessment included development of a rationale and methodology for extrapolating vapor exposures prior to the availability of measurement data, analysis of existing measurement data to estimate task and job exposures during 1975-1985, and extrapolation of truck and marine job exposures before 1975. A worker's vapor exposure was extrapolated from three sets of factors: the tasks in his or her job associated with vapor sources, the characteristics of vapor sources (equipment and other facilities) at the work site, and the composition of petroleum products producing vapors. Historical data were collected on the tasks in job definitions, on work-site facilities, and on product composition. These data were used in a model to estimate the overall time-weighted-average vapor exposure for jobs based on estimates of task exposures and their duration. Task exposures were highest during tank filling in trucks and marine vessels. Measured average annual, full-shift exposures during 1975-1985 ranged from 9 to 14 ppm of total hydrocarbon vapor for truck drivers and 2 to 35 ppm for marine workers on inland waterways. Extrapolated past average exposures in truck operations were highest for truck drivers before 1965 (range 140-220 ppm). Other jobs in truck operations resulted in much lower exposures. Because there were few changes in marine operations before 1979, exposures were assumed to be the same as those measured during 1975-1985. Well-defined exposure gradients were found across jobs within time periods, which were suitable for epidemiologic analyses. PMID:8020436

Operating tool for a distributed data and information management system

NASA Astrophysics Data System (ADS)

Reck, C.; Mikusch, E.; Kiemle, S.; Wolfmüller, M.; Böttcher, M.

2002-07-01

The German Remote Sensing Data Center has developed the Data Information and Management System DIMS which provides multi-mission ground system services for earth observation product processing, archiving, ordering and delivery. DIMS successfully uses newest technologies within its services. This paper presents the solution taken to simplify operation tasks for this large and distributed system.

Workflow for Criticality Assessment Applied in Biopharmaceutical Process Validation Stage 1.

PubMed

Zahel, Thomas; Marschall, Lukas; Abad, Sandra; Vasilieva, Elena; Maurer, Daniel; Mueller, Eric M; Murphy, Patrick; Natschläger, Thomas; Brocard, Cécile; Reinisch, Daniela; Sagmeister, Patrick; Herwig, Christoph

2017-10-12

Identification of critical process parameters that impact product quality is a central task during regulatory requested process validation. Commonly, this is done via design of experiments and identification of parameters significantly impacting product quality (rejection of the null hypothesis that the effect equals 0). However, parameters which show a large uncertainty and might result in an undesirable product quality limit critical to the product, may be missed. This might occur during the evaluation of experiments since residual/un-modelled variance in the experiments is larger than expected a priori. Estimation of such a risk is the task of the presented novel retrospective power analysis permutation test. This is evaluated using a data set for two unit operations established during characterization of a biopharmaceutical process in industry. The results show that, for one unit operation, the observed variance in the experiments is much larger than expected a priori, resulting in low power levels for all non-significant parameters. Moreover, we present a workflow of how to mitigate the risk associated with overlooked parameter effects. This enables a statistically sound identification of critical process parameters. The developed workflow will substantially support industry in delivering constant product quality, reduce process variance and increase patient safety.

24/7 Operational Effectiveness Toolset: Mishap Investigation Interface

DTIC Science & Technology

2008-10-01

analysis software product. The toolset was based upon the Sleep, Activity, Fatigue, and Task Effectiveness (SAFTE™; Hursh et al., 2004). The SAFTE...meeting was for the purpose of requirements analysis , in which the designers elicited task information from the SMEs. The second meeting included a...investigators who also served as our SMEs. The requirements analysis revealed how fatigue related information is entered into the report of an Air Force

Design and Verification

NASA Technical Reports Server (NTRS)

Thompson, Shelby G.; Howard, Robert L., Jr.; Litaker, Harry L., Jr.

2008-01-01

As future space missions become longer, an important aspect to consider is the habitability of the spacecraft. The amount of habitable volume affects not only astronaut comfort, but safety and mission success as well. However, as the volume is increased to aid in task performance, the weight of the vehicle and cost of the mission escalates in proportion. Pressure to reduce mission cost is constant, but the risk to mission success and crew survival must remain the priorities. The Constellation Program's Altair Lunar Lander is designed for short duration surface operation missions of seven to ten days. For short duration missions, humans will tolerate fairly primitive environmental situations provided the basic physiological arrangements are acceptable. However, for long-duration lunar surface operations, the living and operational spaces within which the crew work must provide both the essentials of life, as well as the support necessary for the crew to be productive in accomplishing their mission. The Altair is still in the preliminary design phase, which is the optimal time for Human Factors data to be provided to designers and engineers. A Human Centered Design (HCD) approach is being taken with our Human Factors evaluations. Human-in-the-loop testing is conducted using low-medium fidelity mock-ups of proposed lunar architecture. Based on current ConOps (Concept of Operations) procedures, a task analysis is performed in which individual tasks are combined into larger operational scenarios. Subjective and objective performance measures are gathered at both the task and scenario level. These scores are used to determine the functionality of the vehicle in terms of task performance. Results from these evaluations will highlight areas for design or operational improvement.

Isolation and Purification of Biotechnological Products

NASA Astrophysics Data System (ADS)

Hubbuch, Jürgen; Kula, Maria-Regina

2007-05-01

The production of modern pharma proteins is one of the most rapid growing fields in biotechnology. The overall development and production is a complex task ranging from strain development and cultivation to the purification and formulation of the drug. Downstream processing, however, still accounts for the major part of production costs. This is mainly due to the high demands on purity and thus safety of the final product and results in processes with a sequence of typically more than 10 unit operations. Consequently, even if each process step would operate at near optimal yield, a very significant amount of product would be lost. The majority of unit operations applied in downstream processing have a long history in the field of chemical and process engineering; nevertheless, mathematical descriptions of the respective processes and the economical large-scale production of modern pharmaceutical products are hampered by the complexity of the biological feedstock, especially the high molecular weight and limited stability of proteins. In order to develop new operational steps as well as a successful overall process, it is thus a necessary prerequisite to develop a deeper understanding of the thermodynamics and physics behind the applied processes as well as the implications for the product.

Facility for orbital material processing

NASA Astrophysics Data System (ADS)

Starodubov, D.; McCormick, K.; Dellosa, M.; Erdelyi, E.; Volfson, L.

2018-05-01

The sustainable orbital manufacturing with commercially viable and profitable operation has tremendous potential for driving the space exploration industry and human expansion into outer space. This highly challenging task has never been accomplished before. The current relatively high delivery cost of materials represents the business challenge of value proposition for making products in space. FOMS Inc. team identified an opportunity of fluoride optical fiber manufacturing in space that can lead to the first commercial production on orbit. To address continued cost effective International Space Station (ISS) operations FOMS Inc. has developed and demonstrated for the first time a fully operational space facility for orbital remote manufacturing with up to 50 km fiber fabrication capability and strong commercial potential for manufacturing operations on board the ISS.

Entanglement as a resource to distinguish orthogonal product states

PubMed Central

Zhang, Zhi-Chao; Gao, Fei; Cao, Tian-Qing; Qin, Su-Juan; Wen, Qiao-Yan

2016-01-01

It is known that there are many sets of orthogonal product states which cannot be distinguished perfectly by local operations and classical communication (LOCC). However, these discussions have left the following open question: What entanglement resources are necessary and/or sufficient for this task to be possible with LOCC? In m ⊗ n, certain classes of unextendible product bases (UPB) which can be distinguished perfectly using entanglement as a resource, had been presented in 2008. In this paper, we present protocols which use entanglement more efficiently than teleportation to distinguish some classes of orthogonal product states in m ⊗ n, which are not UPB. For the open question, our results offer rather general insight into why entanglement is useful for such tasks, and present a better understanding of the relationship between entanglement and nonlocality. PMID:27458034

Circuit modification and research of operation modes of high-frequency pulsed resonant converter of the X-ray tube power supply

NASA Astrophysics Data System (ADS)

Klonov, V. V.; Larionov, I. A.; Bessonov, V. B.

2018-02-01

Despite obvious drawbacks of the resonant converter, such as complicated calculation, increased size and weight of the device, deviations of the circuit parameters from product to product, the resonant converter shows significant advantages in comparison with other. The task was to design the generator, which is built on a resonant topology.

The FOT tool kit concept

NASA Technical Reports Server (NTRS)

Fatig, Michael

1993-01-01

Flight operations and the preparation for it has become increasingly complex as mission complexities increase. Further, the mission model dictates that a significant increase in flight operations activities is upon us. Finally, there is a need for process improvement and economy in the operations arena. It is therefore time that we recognize flight operations as a complex process requiring a defined, structured, and life cycle approach vitally linked to space segment, ground segment, and science operations processes. With this recognition, an FOT Tool Kit consisting of six major components designed to provide tools to guide flight operations activities throughout the mission life cycle was developed. The major components of the FOT Tool Kit and the concepts behind the flight operations life cycle process as developed at NASA's GSFC for GSFC-based missions are addressed. The Tool Kit is therefore intended to increase productivity, quality, cost, and schedule performance of the flight operations tasks through the use of documented, structured methodologies; knowledge of past lessons learned and upcoming new technology; and through reuse and sharing of key products and special application programs made possible through the development of standardized key products and special program directories.

Ergonomics and design: its principles applied in the industry.

PubMed

Tavares, Ademario Santos; Silva, Francisco Nilson da

2012-01-01

Industrial Design encompasses both product development and optimization of production process. In this sense, Ergonomics plays a fundamental role, because its principles, methods and techniques can help operators to carry out their tasks most successfully. A case study carried out in an industry shows that the interaction among Design, Production Engineering and Materials Engineering departments may improve some aspects concerned security, comfort, efficiency and performance. In this process, Ergonomics had shown to be of essential importance to strategic decision making to the improvement of production section.

Biological production of ethanol from coal. Task 4 report, Continuous reactor studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The production of ethanol from synthesis gas by the anaerobic bacterium C. ljungdahlii has been demonstrated in continuous stirred tank reactors (CSTRs), CSTRs with cell recycle and trickle bed reactors. Various liquid media were utilized in these studies including basal medium, basal media with 1/2 B-vitamins and no yeast extract and a medium specifically designed for the growth of C. ljungdahlii in the CSTR. Ethanol production was successful in each of the three reactor types, although trickle bed operation with C. ljungdahlii was not as good as with the stirred tank reactors. Operation in the CSTR with cell recycle wasmore » particularly promising, producing 47 g/L ethanol with only minor concentrations of the by-product acetate.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flory, John Andrew; Padilla, Denise D.; Gauthier, John H.

Upcoming weapon programs require an aggressive increase in Application Specific Integrated Circuit (ASIC) production at Sandia National Laboratories (SNL). SNL has developed unique modeling and optimization tools that have been instrumental in improving ASIC production productivity and efficiency, identifying optimal operational and tactical execution plans under resource constraints, and providing confidence in successful mission execution. With ten products and unprecedented levels of demand, a single set of shared resources, highly variable processes, and the need for external supplier task synchronization, scheduling is an integral part of successful manufacturing. The scheduler uses an iterative multi-objective genetic algorithm and a multi-dimensional performancemore » evaluator. Schedule feasibility is assessed using a discrete event simulation (DES) that incorporates operational uncertainty, variability, and resource availability. The tools provide rapid scenario assessments and responses to variances in the operational environment, and have been used to inform major equipment investments and workforce planning decisions in multiple SNL facilities.« less

Programmable Positioner For Spot Welding

NASA Technical Reports Server (NTRS)

Roden, William A.

1989-01-01

Welding station mechanized by installing preset indexing system and gear drive. Mechanism includes a low-cost, versatile, single-axis motion control and motor drive to provide fully-automatic weld sequencing and spot-to-spot spacing. Welding station relieves operator of some difficult, tedious tasks and increases both productivity and quality of welds. Results in welds of higher quality and greater accuracy, fewer weld defects, and faster welding operation.

P-8A Poseidon Multi-Mission Maritime Aircraft (P-8A)

DTIC Science & Technology

2013-12-01

NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND...2013 rated the P-8A as operationally effective , operationally suitable, and recommended Fleet introduction. Integrated testing of deficiency...lot through effective negotiations with the prime contractor and through development and implementation of production process improvement

Automated Scheduling Via Artificial Intelligence

NASA Technical Reports Server (NTRS)

Biefeld, Eric W.; Cooper, Lynne P.

1991-01-01

Artificial-intelligence software that automates scheduling developed in Operations Mission Planner (OMP) research project. Software used in both generation of new schedules and modification of existing schedules in view of changes in tasks and/or available resources. Approach based on iterative refinement. Although project focused upon scheduling of operations of scientific instruments and other equipment aboard spacecraft, also applicable to such terrestrial problems as scheduling production in factory.

Mechanical Transformation of Task Heuristics into Operational Procedures

DTIC Science & Technology

1981-04-14

Introduction A central theme of recent research in artificial intelligence is that *Intelligent task performance requires large amounts of knowledge...PLAY P1 C4] (. (LEADING (QSO)) (OR (CAN-LEAO- HEARrS (gSO)J (mEg (SUIT-OF C3) H])] C-) (FOLLOWING (QSO)) (OR [VOID (OSO) (SUIT-LED)3 [IN-SUIT C3 (SUIT...Production rules as a representation for a knowledge based consultation system. Artificial Intelligence 8:15-45, Spring, 1977. [Davis 77b] R. Davis

Biological monitoring of benzene exposure for process operators during ordinary activity in the upstream petroleum industry.

PubMed

Bråtveit, Magne; Kirkeleit, Jorunn; Hollund, Bjørg Eli; Moen, Bente E

2007-07-01

This study characterized the exposure of crude oil process operators to benzene and related aromatics during ordinary activity and investigated whether the operators take up benzene at this level of exposure. We performed the study on a fixed, integrated oil and gas production facility on Norway's continental shelf. The study population included 12 operators and 9 referents. We measured personal exposure to benzene, toluene, ethylbenzene and xylene during three consecutive 12-h work shifts using organic vapour passive dosimeter badges. We sampled blood and urine before departure to the production facility (pre-shift), immediately after the work shift on Day 13 of the work period (post-shift) and immediately before the following work shift (pre-next shift). We also measured the exposure to hydrocarbons during short-term tasks by active sampling using Tenax tubes. The arithmetic mean exposure over the 3 days was 0.042 ppm for benzene (range <0.001-0.69 ppm), 0.05 ppm for toluene, 0.02 ppm for ethylbenzene and 0.03 ppm for xylene. Full-shift personal exposure was significantly higher when the process operators performed flotation work during the shift versus other tasks. Work in the flotation area was associated with short-term (6-15 min) arithmetic mean exposure to benzene of 1.06 ppm (range 0.09-2.33 ppm). The concentrations of benzene in blood and urine did not differ between operators and referents at any time point. When we adjusted for current smoking in regression analysis, benzene exposure was significantly associated with the post-shift concentration of benzene in blood (P = 0.01) and urine (P = 0.03), respectively. Although these operators perform tasks with relatively high short-term exposure to benzene, the full-shift mean exposure is low during ordinary activity. Some evidence indicates benzene uptake within this range of exposure.

Biomass-derived Syngas Utilization for Fuels and Chemicals - Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dayton, David C

2010-03-24

Executive Summary The growing gap between petroleum production and demand, mounting environmental concerns, and increasing fuel prices have stimulated intense interest in research and development (R&D) of alternative fuels, both synthetic and bio-derived. Currently, the most technically defined thermochemical route for producing alternative fuels from lignocellulosic biomass involves gasification/reforming of biomass to produce syngas (carbon monoxide [CO] + hydrogen [H2]), followed by syngas cleaning, Fischer-Tropsch synthesis (FTS) or mixed alcohol synthesis, and some product upgrading via hydroprocessing or separation. A detailed techno-economic analysis of this type of process has recently been published [1] and it highlights the need for technicalmore » breakthroughs and technology demonstration for gas cleanup and fuel synthesis. The latter two technical barrier areas contribute 40% of the total thermochemical ethanol cost and 70% of the production cost, if feedstock costs are factored out. Developing and validating technologies that reduce the capital and operating costs of these unit operations will greatly reduce the risk for commercializing integrated biomass gasification/fuel synthesis processes for biofuel production. The objective of this project is to develop and demonstrate new catalysts and catalytic processes that can efficiently convert biomass-derived syngas into diesel fuel and C2-C4 alcohols. The goal is to improve the economics of the processes by improving the catalytic activity and product selectivity, which could lead to commercialization. The project was divided into 4 tasks: Task 1: Reactor Systems: Construction of three reactor systems was a project milestone. Construction of a fixed-bed microreactor (FBR), a continuous stirred tank reactor (CSTR), and a slurry bubble column reactor (SBCR) were completed to meet this milestone. Task 2: Iron Fischer-Tropsch (FT) Catalyst: An attrition resistant iron FT catalyst will be developed and tested. Task 3: Chemical Synthesis: Promising process routes will be identified for synthesis of selected chemicals from biomass-derived syngas. A project milestone was to select promising mixed alcohol catalysts and screen productivity and performance in a fixed bed micro-reactor using bottled syngas. This milestone was successfully completed in collaboration withour catalyst development partner. Task 4: Modeling, Engineering Evaluation, and Commercial Assessment: Mass and energy balances of conceptual commercial embodiment for FT and chemical synthesis were completed.« less

The role of production and teamwork practices in construction safety: a cognitive model and an empirical case study.

PubMed

Mitropoulos, Panagiotis Takis; Cupido, Gerardo

2009-01-01

In construction, the challenge for researchers and practitioners is to develop work systems (production processes and teams) that can achieve high productivity and high safety at the same time. However, construction accident causation models ignore the role of work practices and teamwork. This study investigates the mechanisms by which production and teamwork practices affect the likelihood of accidents. The paper synthesizes a new model for construction safety based on the cognitive perspective (Fuller's Task-Demand-Capability Interface model, 2005) and then presents an exploratory case study. The case study investigates and compares the work practices of two residential framing crews: a 'High Reliability Crew' (HRC)--that is, a crew with exceptional productivity and safety over several years, and an average performing crew from the same company. The model explains how the production and teamwork practices generate the work situations that workers face (the task demands) and affect the workers ability to cope (capabilities). The case study indicates that the work practices of the HRC directly influence the task demands and match them with the applied capabilities. These practices were guided by the 'principle' of avoiding errors and rework and included work planning and preparation, work distribution, managing the production pressures, and quality and behavior monitoring. The Task Demand-Capability model links construction research to a cognitive model of accident causation and provides a new way to conceptualize safety as an emergent property of the production practices and teamwork processes. The empirical evidence indicates that the crews' work practices and team processes strongly affect the task demands, the applied capabilities, and the match between demands and capabilities. The proposed model and the exploratory case study will guide further discovery of work practices and teamwork processes that can increase both productivity and safety in construction operations. Such understanding will enable training of construction foremen and crews in these practices to systematically develop high reliability crews.

Improving machine operation management efficiency via improving the vehicle park structure and using the production operation information database

NASA Astrophysics Data System (ADS)

Koptev, V. Yu

2017-02-01

The work represents the results of studying basic interconnected criteria of separate equipment units of the transport network machines fleet, depending on production and mining factors to improve the transport systems management. Justifying the selection of a control system necessitates employing new methodologies and models, augmented with stability and transport flow criteria, accounting for mining work development dynamics on mining sites. A necessary condition is the accounting of technical and operating parameters related to vehicle operation. Modern open pit mining dispatching systems must include such kinds of the information database. An algorithm forming a machine fleet is presented based on multi-variation task solution in connection with defining reasonable operating features of a machine working as a part of a complex. Proposals cited in the work may apply to mining machines (drilling equipment, excavators) and construction equipment (bulldozers, cranes, pile-drivers), city transport and other types of production activities using machine fleet.

The ATLAS Production System Evolution: New Data Processing and Analysis Paradigm for the LHC Run2 and High-Luminosity

NASA Astrophysics Data System (ADS)

Barreiro, F. H.; Borodin, M.; De, K.; Golubkov, D.; Klimentov, A.; Maeno, T.; Mashinistov, R.; Padolski, S.; Wenaus, T.; ATLAS Collaboration

2017-10-01

The second generation of the ATLAS Production System called ProdSys2 is a distributed workload manager that runs daily hundreds of thousands of jobs, from dozens of different ATLAS specific workflows, across more than hundred heterogeneous sites. It achieves high utilization by combining dynamic job definition based on many criteria, such as input and output size, memory requirements and CPU consumption, with manageable scheduling policies and by supporting different kind of computational resources, such as GRID, clouds, supercomputers and volunteer-computers. The system dynamically assigns a group of jobs (task) to a group of geographically distributed computing resources. Dynamic assignment and resources utilization is one of the major features of the system, it didn’t exist in the earliest versions of the production system where Grid resources topology was predefined using national or/and geographical pattern. Production System has a sophisticated job fault-recovery mechanism, which efficiently allows to run multi-Terabyte tasks without human intervention. We have implemented “train” model and open-ended production which allow to submit tasks automatically as soon as new set of data is available and to chain physics groups data processing and analysis with central production by the experiment. We present an overview of the ATLAS Production System and its major components features and architecture: task definition, web user interface and monitoring. We describe the important design decisions and lessons learned from an operational experience during the first year of LHC Run2. We also report the performance of the designed system and how various workflows, such as data (re)processing, Monte-Carlo and physics group production, users analysis, are scheduled and executed within one production system on heterogeneous computing resources.

Biogeography-based combinatorial strategy for efficient autonomous underwater vehicle motion planning and task-time management

NASA Astrophysics Data System (ADS)

Zadeh, S. M.; Powers, D. M. W.; Sammut, K.; Yazdani, A. M.

2016-12-01

Autonomous Underwater Vehicles (AUVs) are capable of spending long periods of time for carrying out various underwater missions and marine tasks. In this paper, a novel conflict-free motion planning framework is introduced to enhance underwater vehicle's mission performance by completing maximum number of highest priority tasks in a limited time through a large scale waypoint cluttered operating field, and ensuring safe deployment during the mission. The proposed combinatorial route-path planner model takes the advantages of the Biogeography-Based Optimization (BBO) algorithm toward satisfying objectives of both higher-lower level motion planners and guarantees maximization of the mission productivity for a single vehicle operation. The performance of the model is investigated under different scenarios including the particular cost constraints in time-varying operating fields. To show the reliability of the proposed model, performance of each motion planner assessed separately and then statistical analysis is undertaken to evaluate the total performance of the entire model. The simulation results indicate the stability of the contributed model and its feasible application for real experiments.

Understanding facilities design parameters for a remanufacturing system

NASA Astrophysics Data System (ADS)

Topcu, Aysegul; Cullinane, Thomas

2005-11-01

Remanufacturing is rapidly becoming a very important element in the economies of the world. Products such as washing machines, clothes driers, automobile parts, cell phones and a wide range of consumer durable goods are being reclaimed and sent through processes that restore these products to levels of operating performance that are as good or better than their new product performance. The operations involved in the remanufacturing process add several new dimensions to the work that must be performed. Disassembly is an operation that rarely appears on the operations chart of a typical production facility. The inspection and test functions in remanufacturing most often involve several more tasks than those involved in the first time manufacturing cycle. A close evaluation of most any remanufacturing operation reveals several points in the process in which parts must be cleaned, tested and stored. Although several researchers have focused their work on optimizing the disassembly function and the inspection, test and store functions, very little research has been devoted to studying the impact of the facilities design on the effectiveness of the remanufacturing process. The purpose of this paper will be to delineate the differences between first time manufacturing operations and remanufacturing operations for durable goods and to identify the features of the facilities design that must be considered if the remanufacturing operations are to be effective.

Space engineering

NASA Technical Reports Server (NTRS)

Alexander, Harold L.

1991-01-01

Human productivity was studied for extravehicular tasks performed in microgravity, particularly including in-space assembly of truss structures and other large objects. Human factors research probed the anthropometric constraints imposed on microgravity task performance and the associated workstation design requirements. Anthropometric experiments included reach envelope tests conducted using the 3-D Acoustic Positioning System (3DAPS), which permitted measuring the range of reach possible for persons using foot restraints in neutral buoyancy, both with and without space suits. Much neutral buoyancy research was conducted using the support of water to simulate the weightlessness environment of space. It became clear over time that the anticipated EVA requirement associated with the Space Station and with in-space construction of interplanetary probes would heavily burden astronauts, and remotely operated robots (teleoperators) were increasingly considered to absorb the workload. Experience in human EVA productivity led naturally to teleoperation research into the remote performance of tasks through human controlled robots.

Sensor assignment to mission in AI-TECD

NASA Astrophysics Data System (ADS)

Ganger, Robert; de Mel, Geeth; Pham, Tien; Rudnicki, Ronald; Schreiber, Yonatan

2016-05-01

Sensor-mission assignment involves the allocation of sensors and other information-providing resources to missions in order to cover the information needs of the individual tasks within each mission. The importance of efficient and effective means to find appropriate resources for tasks is exacerbated in the coalition context where the operational environment is dynamic and a multitude of critically important tasks need to achieve their collective goals to meet the objectives of the coalition. The Sensor Assignment to Mission (SAM) framework—a research product of the International Technology Alliance in Network and Information Sciences (NIS-ITA) program—provided the first knowledge intensive resource selection approach for the sensor network domain so that contextual information could be used to effectively select resources for tasks in coalition environments. Recently, CUBRC, Inc. was tasked with operationalizing the SAM framework through the use of the I2WD Common Core Ontologies for the Communications-Electronics Research, Development and Engineering Center (CERDEC) sponsored Actionable Intelligence Technology Enabled Capabilities Demonstration (AI-TECD). The demonstration event took place at Fort Dix, New Jersey during July 2015, and this paper discusses the integration and the successful demonstration of the SAM framework within the AI-TECD, lessons learned, and its potential impact in future operations.

Evaluation of target efficiencies for solid-liquid separation steps in biofuels production.

PubMed

Kochergin, Vadim; Miller, Keith

2011-01-01

Development of liquid biofuels has entered a new phase of large scale pilot demonstration. A number of plants that are in operation or under construction face the task of addressing the engineering challenges of creating a viable plant design, scaling up and optimizing various unit operations. It is well-known that separation technologies account for 50-70% of both capital and operating cost. Additionally, reduction of environmental impact creates technological challenges that increase project cost without adding to the bottom line. Different technologies vary in terms of selection of unit operations; however, solid-liquid separations are likely to be a major contributor to the overall project cost. Despite the differences in pretreatment approaches, similar challenges arise for solid-liquid separation unit operations. A typical process for ethanol production from biomass includes several solid-liquid separation steps, depending on which particular stream is targeted for downstream processing. The nature of biomass-derived materials makes it either difficult or uneconomical to accomplish complete separation in a single step. Therefore, setting realistic efficiency targets for solid-liquid separations is an important task that influences overall process recovery and economics. Experimental data will be presented showing typical characteristics for pretreated cane bagasse at various stages of processing into cellulosic ethanol. Results of generic material balance calculations will be presented to illustrate the influence of separation target efficiencies on overall process recoveries and characteristics of waste streams.

High conversion of coal to transportation fuels for the future with low HC gas production. Progress report Number 10, January 1--March 31, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiser, W.H.; Oblad, A.G.

1995-04-01

An objective of the Department of Energy in funding research in coal liquefaction, is to produce a synthetic crude from coal at a cost lower than $30.00 per barrel (Task A). A second objective is to produce a fuel which is low in aromatics, yet of sufficiently high octane number for use in the gasoline-burning transportation vehicles of today. To meet this second objective, research was proposed for conversion of the highly-aromatic liquid product from coal conversion to a product high in isoparaffins, which compounds in the gasoline range exhibit a high octane number (Task B). Experimental coal liquefaction studiesmore » conducted in a batch microreactor have demonstrated potential for high conversions of coal to liquids with low yields of hydrocarbon (HC) gases, hence small consumption of hydrogen in the primary liquefaction step. Ratios of liquids/HC gases as high as 30/1, at liquid yields as high as 82% of the coal by weight, have been achieved. The principal objective of this work is to examine how nearly one may approach these results in a continuous-flow system, at a size sufficient to evaluate the process concept for production of transportation fuels from coal. A continuous-flow reactor system is to be designed, constructed and operated. The system is to be computer-operated for process control and data logging, and is to be fully instrumented. The primary liquid products will be characterized by GC, FTIR, and GC/MS, to determine the types and quantities of the principal components produced under conditions of high liquids production with high ratios of liquids/HC gases. From these analyses, together with GC analyses of the HC gases, hydrogen consumption for the conversion to primary liquids will be calculated. Conversion of the aromatics of this liquid product to isoparaffins will be investigated. Results to date on both tasks are presented.« less

Modeling operators' emergency response time for chemical processing operations.

PubMed

Murray, Susan L; Harputlu, Emrah; Mentzer, Ray A; Mannan, M Sam

2014-01-01

Operators have a crucial role during emergencies at a variety of facilities such as chemical processing plants. When an abnormality occurs in the production process, the operator often has limited time to either take corrective actions or evacuate before the situation becomes deadly. It is crucial that system designers and safety professionals can estimate the time required for a response before procedures and facilities are designed and operations are initiated. There are existing industrial engineering techniques to establish time standards for tasks performed at a normal working pace. However, it is reasonable to expect the time required to take action in emergency situations will be different than working at a normal production pace. It is possible that in an emergency, operators will act faster compared to a normal pace. It would be useful for system designers to be able to establish a time range for operators' response times for emergency situations. This article develops a modeling approach to estimate the time standard range for operators taking corrective actions or following evacuation procedures in emergency situations. This will aid engineers and managers in establishing time requirements for operators in emergency situations. The methodology used for this study combines a well-established industrial engineering technique for determining time requirements (predetermined time standard system) and adjustment coefficients for emergency situations developed by the authors. Numerous videos of workers performing well-established tasks at a maximum pace were studied. As an example, one of the tasks analyzed was pit crew workers changing tires as quickly as they could during a race. The operations in these videos were decomposed into basic, fundamental motions (such as walking, reaching for a tool, and bending over) by studying the videos frame by frame. A comparison analysis was then performed between the emergency pace and the normal working pace operations to determine performance coefficients. These coefficients represent the decrease in time required for various basic motions in emergency situations and were used to model an emergency response. This approach will make hazardous operations requiring operator response, alarm management, and evacuation processes easier to design and predict. An application of this methodology is included in the article. The time required for an emergency response was roughly a one-third faster than for a normal response time.

A Machine Vision Quality Control System for Industrial Acrylic Fibre Production

NASA Astrophysics Data System (ADS)

Heleno, Paulo; Davies, Roger; Correia, Bento A. Brázio; Dinis, João

2002-12-01

This paper describes the implementation of INFIBRA, a machine vision system used in the quality control of acrylic fibre production. The system was developed by INETI under a contract with a leading industrial manufacturer of acrylic fibres. It monitors several parameters of the acrylic production process. This paper presents, after a brief overview of the system, a detailed description of the machine vision algorithms developed to perform the inspection tasks unique to this system. Some of the results of online operation are also presented.

Cost accounting, management control, and planning in health care.

PubMed

Siegrist, R B; Blish, C S

1988-02-01

Advantages and pharmacy applications of computerized hospital management-control and planning systems are described. Hospitals must define their product lines; patient cases, not tests or procedures, are the end product. Management involves operational control, management control, and strategic planning. Operational control deals with day-to-day management on the task level. Management control involves ensuring that managers use resources effectively and efficiently to accomplish the organization's objectives. Management control includes both control of unit costs of intermediate products, which are procedures and services used to treat patients and are managed by hospital department heads, and control of intermediate product use per case (managed by the clinician). Information from the operation and management levels feeds into the strategic plan; conversely, the management level controls the plan and the operational level carries it out. In the system developed at New England Medical Center, Boston, Massachusetts, the intermediate product-management system enables managers to identify intermediate products, develop standard costs, simulate changes in departmental costs, and perform variance analysis. The end-product management system creates a patient-level data-base, identifies end products (patient-care groupings), develops standard resource protocols, models alternative assumptions, performs variance analysis, and provides concurrent reporting. Examples are given of pharmacy managers' use of such systems to answer questions in the areas of product costing, product pricing, variance analysis, productivity monitoring, flexible budgeting, modeling and planning, and comparative analysis.(ABSTRACT TRUNCATED AT 250 WORDS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ji Zhengfeng; Feng Yuan; Ying Mingsheng

Local quantum operations and classical communication (LOCC) put considerable constraints on many quantum information processing tasks such as cloning and discrimination. Surprisingly, however, discrimination of any two pure states survives such constraints in some sense. We show that cloning is not that lucky; namely, probabilistic LOCC cloning of two product states is strictly less efficient than global cloning. We prove our result by giving explicitly the efficiency formula of local cloning of any two product states.

EOS MLS Level 2 Data Processing Software Version 3

NASA Technical Reports Server (NTRS)

Livesey, Nathaniel J.; VanSnyder, Livesey W.; Read, William G.; Schwartz, Michael J.; Lambert, Alyn; Santee, Michelle L.; Nguyen, Honghanh T.; Froidevaux, Lucien; wang, Shuhui; Manney, Gloria L.;

A computerized aircraft battery servicing facility

NASA Technical Reports Server (NTRS)

Glover, Richard D.

1992-01-01

The latest upgrade to the Aerospace Energy Systems Laboratory (AESL) is described. The AESL is a distributed digital system consisting of a central system and battery servicing stations connected by a high-speed serial data bus. The entire system is located in two adjoining rooms; the bus length is approximately 100 ft. Each battery station contains a digital processor, data acquisition, floppy diskette data storage, and operator interfaces. The operator initiates a servicing task and thereafter the battery station monitors the progress of the task and terminates it at the appropriate time. The central system provides data archives, manages the data bus, and provides a timeshare interface for multiple users. The system also hosts software production tools for the battery stations and the central system.

Automated Sequence Processor: Something Old, Something New

NASA Technical Reports Server (NTRS)

Streiffert, Barbara; Schrock, Mitchell; Fisher, Forest; Himes, Terry

2012-01-01

High productivity required for operations teams to meet schedules Risk must be minimized. Scripting used to automate processes. Scripts perform essential operations functions. Automated Sequence Processor (ASP) was a grass-roots task built to automate the command uplink process System engineering task for ASP revitalization organized. ASP is a set of approximately 200 scripts written in Perl, C Shell, AWK and other scripting languages.. ASP processes/checks/packages non-interactive commands automatically.. Non-interactive commands are guaranteed to be safe and have been checked by hardware or software simulators.. ASP checks that commands are non-interactive.. ASP processes the commands through a command. simulator and then packages them if there are no errors.. ASP must be active 24 hours/day, 7 days/week..

Comparison of multiobjective evolutionary algorithms for operations scheduling under machine availability constraints.

PubMed

Frutos, M; Méndez, M; Tohmé, F; Broz, D

2013-01-01

Many of the problems that arise in production systems can be handled with multiobjective techniques. One of those problems is that of scheduling operations subject to constraints on the availability of machines and buffer capacity. In this paper we analyze different Evolutionary multiobjective Algorithms (MOEAs) for this kind of problems. We consider an experimental framework in which we schedule production operations for four real world Job-Shop contexts using three algorithms, NSGAII, SPEA2, and IBEA. Using two performance indexes, Hypervolume and R2, we found that SPEA2 and IBEA are the most efficient for the tasks at hand. On the other hand IBEA seems to be a better choice of tool since it yields more solutions in the approximate Pareto frontier.

The smooth (tractor) operator: insights of knowledge engineering.

PubMed

Cullen, Ralph H; Smarr, Cory-Ann; Serrano-Baquero, Daniel; McBride, Sara E; Beer, Jenay M; Rogers, Wendy A

2012-11-01

The design of and training for complex systems requires in-depth understanding of task demands imposed on users. In this project, we used the knowledge engineering approach (Bowles et al., 2004) to assess the task of mowing in a citrus grove. Knowledge engineering is divided into four phases: (1) Establish goals. We defined specific goals based on the stakeholders involved. The main goal was to identify operator demands to support improvement of the system. (2) Create a working model of the system. We reviewed product literature, analyzed the system, and conducted expert interviews. (3) Extract knowledge. We interviewed tractor operators to understand their knowledge base. (4) Structure knowledge. We analyzed and organized operator knowledge to inform project goals. We categorized the information and developed diagrams to display the knowledge effectively. This project illustrates the benefits of knowledge engineering as a qualitative research method to inform technology design and training. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Acquisition and production of skilled behavior in dynamic decision-making tasks: Modeling strategic behavior in human-automation interaction: Why and aid can (and should) go unused

NASA Technical Reports Server (NTRS)

Kirlik, Alex

1991-01-01

Advances in computer and control technology offer the opportunity for task-offload aiding in human-machine systems. A task-offload aid (e.g., an autopilot, an intelligent assistant) can be selectively engaged by the human operator to dynamically delegate tasks to an automated system. Successful design and performance prediction in such systems requires knowledge of the factors influencing the strategy the operator develops and uses for managing interaction with the task-offload aid. A model is presented that shows how such strategies can be predicted as a function of three task context properties (frequency and duration of secondary tasks and costs of delaying secondary tasks) and three aid design properties (aid engagement and disengagement times, aid performance relative to human performance). Sensitivity analysis indicates how each of these contextual and design factors affect the optimal aid aid usage strategy and attainable system performance. The model is applied to understanding human-automation interaction in laboratory experiments on human supervisory control behavior. The laboratory task allowed subjects freedom to determine strategies for using an autopilot in a dynamic, multi-task environment. Modeling results suggested that many subjects may indeed have been acting appropriately by not using the autopilot in the way its designers intended. Although autopilot function was technically sound, this aid was not designed with due regard to the overall task context in which it was placed. These results demonstrate the need for additional research on how people may strategically manage their own resources, as well as those provided by automation, in an effort to keep workload and performance at acceptable levels.

Power Extension Package (PEP) system definition extension, orbital service module systems analysis study. Volume 9: PEP design, development and test plans

NASA Technical Reports Server (NTRS)

1979-01-01

A plan for the production of two PEP flight systems is defined. The task's milestones are described. Provisions for the development and assembly of new ground support equipment required for both testing and launch operations are included.

Seeing Results in Flooring for Schools

ERIC Educational Resources Information Center

Simmons, Brian

2011-01-01

Operations staffs at education facilities of all sizes are tasked with selecting a hard floor cleaning program that is cost-effective, efficient and highly productive. With an increased focus on the sustainability of an environment, facility managers also must select a program that meets sustainability goals while maintaining a healthful, safe…

On intra-supply chain system with an improved distribution plan, multiple sales locations and quality assurance.

PubMed

Chiu, Singa Wang; Huang, Chao-Chih; Chiang, Kuo-Wei; Wu, Mei-Fang

2015-01-01

Transnational companies, operating in extremely competitive global markets, always seek to lower different operating costs, such as inventory holding costs in their intra- supply chain system. This paper incorporates a cost reducing product distribution policy into an intra-supply chain system with multiple sales locations and quality assurance studied by [Chiu et al., Expert Syst Appl, 40:2669-2676, (2013)]. Under the proposed cost reducing distribution policy, an added initial delivery of end items is distributed to multiple sales locations to meet their demand during the production unit's uptime and rework time. After rework when the remaining production lot goes through quality assurance, n fixed quantity installments of finished items are then transported to sales locations at a fixed time interval. Mathematical modeling and optimization techniques are used to derive closed-form optimal operating policies for the proposed system. Furthermore, the study demonstrates significant savings in stock holding costs for both the production unit and sales locations. Alternative of outsourcing product delivery task to an external distributor is analyzed to assist managerial decision making in potential outsourcing issues in order to facilitate further reduction in operating costs.

Non-destructive testing method for determining the solvent diffusion coefficient in the porous materials products

NASA Astrophysics Data System (ADS)

Belyaev, V. P.; Mishchenko, S. V.; Belyaev, P. S.

2018-01-01

Ensuring non-destructive testing of products in industry is an urgent task. Most of the modern methods for determining the diffusion coefficient in porous materials have been developed for bodies of a given configuration and size. This leads to the need for finished products destruction to make experimental samples from them. The purpose of this study is the development of a dynamic method that allows operatively determine the diffusion coefficient in finished products from porous materials without destroying them. The method is designed to investigate the solvents diffusion coefficient in building constructions from materials having a porous structure: brick, concrete and aerated concrete, gypsum, cement, gypsum or silicate solutions, gas silicate blocks, heat insulators, etc. A mathematical model of the method is constructed. The influence of the design and measuring device operating parameters on the method accuracy is studied. The application results of the developed method for structural porous products are presented.

Space station System Engineering and Integration (SE and I). Volume 2: Study results

NASA Technical Reports Server (NTRS)

1987-01-01

A summary of significant study results that are products of the Phase B conceptual design task are contained. Major elements are addressed. Study results applicable to each major element or area of design are summarized and included where appropriate. Areas addressed include: system engineering and integration; customer accommodations; test and program verification; product assurance; conceptual design; operations and planning; technical and management information system (TMIS); and advanced development.

3D sensing for machine guidance in meat cutting applications

NASA Astrophysics Data System (ADS)

Daley, Wayne; Britton, Doug; Usher, Colin; Diao, Mamadou; Ruffin, Kevin

2005-11-01

Most cutting and deboning operations in meat processing require accurate cuts be made to obtain maximum yield and ensure food safety. This is a significant concern for purveyors of deboned product. This task is made more difficult by the variability that is present in most natural products. The specific application of interest in this paper is the production of deboned poultry breast. This is typically obtained from a cut of the broiler called a 'front half' that includes the breast and the wings. The deboning operation typically consists of a cut that starts at the shoulder joint and then continues along the scapula. Attentive humans with training do a very good job of making this cut. The breast meat is then removed by pulling on the wings. Inaccurate cuts lead to poor yield (amount of boneless meat obtained relative to the weight of the whole carcass) and increase the probability that bone fragments might end up in the product. As equipment designers seek to automate the deboning operation, the cutting task has been a significant obstacle to developing automation that maximizes yield without generating unacceptable levels of bone fragments. The current solution is to sort the bone-in product into different weight ranges and then to adjust the deboning machines to the average of these weight ranges. We propose an approach for obtaining key cut points by extrapolation from external reference points based on the anatomy of the bird. We show that this approach can be implemented using a stereo imaging system, and the accuracy in locating the cut points of interest is significantly improved. This should result in more accurate cuts and with this concomitantly improved yield while reducing the incidence of bones. We also believe the approach could be extended to the processing of other species.

Novel Surface Modification Method for Ultrasupercritical Coal-Fired Boilers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiao, T. Danny

2013-05-22

US Department of Energy seeks an innovative coating technology for energy production to reduce the emission of SOx, NOx, and CO2 toxic gaseous species. To realize this need, Inframat Corporation (IMC) proposed an SPS thermal spray coating technique to produce ultrafine/nanocoatings that can be deposited onto the surfaces of high temperature boiler tubes, so that higher temperatures of boiler operation becomes possible, leading to significantly reduced emission of toxic gaseous species. It should be noted that the original PI was Dr. Xinqing Ma, who after 1.5 year conducting this project left Inframat in December, 2008. Thus, the PI was transferredmore » to Dr. Danny Xiao, who originally co-authored the proposal with Dr. Ma, in order to carry the project into a completion. Phase II Objectives: The proposed technology has the following attributes, including: (1). Dispersion of a nanoparticle or alloyed particle in a solvent to form a uniform slurry feedstock; (2). Feeding of the slurry feedstock into a thermal spray flame, followed by deposition of the slurry feedstock onto substrates to form tenacious nanocoatings; (3). High coating performance: including high bonding strength, and high temperature service life in the temperature range of 760oC/1400oF. Following the above premises, our past Phase I project has demonstrated the feasibility in small scale coatings on boiler substrates. The objective of this Phase II project was to focus on scale-up the already demonstrated Phase I work for the fabrication of SPS coatings that can satisfy DOE's emission reduction goals for energy production operations. Specifically, they are: (1). Solving engineering problems to scale-up the SPS-HVOF delivery system to a prototype production sub-delivery system; (2). Produce ultrafine/nanocoatings using the scale-up prototype system; (3). Demonstrate the coated components using the scale-up device having superior properties. Proposed Phase II Tasks: In the original Phase II proposal, we have six (6) technical tasks plus one (1) reporting task, as described below: Task 1 Scale-up and optimize the SPS process; Task 2 Coating design and fabrication with desired microstructure; Task 3 Evaluate microstructure and physical properties; Task 4 Test performance of long-term corrosion and erosion; Task 5 Test mechanical property and reliability; Task 6 Coating of a prototype boiler tube for evaluation; Task 7 Reporting task. To date, we have already completed all the technical tasks of 1 through 6. Major Phase II Achievements: In this four (4) year working period, Inframat had spent great effort to complete the proposed tasks. The project had been completed; the goals have been accomplished. Major achievements obtained include: (1). Developed a prototype scale-up slurry feedstock delivery system for thermal spray coatings; (2). Successfully coated high performance coatings using this scale-up slurry delivery system; (3). Commercial applications in energy efficiency and clean energy components have been developed using this newly fabricated slurry feedstock delivery system.« less

Ergonomics investigation of retail ice cream operations.

PubMed

Dempsey, P G; McGorry, R R; Cotnam, J; Braun, T W

2000-04-01

A comprehensive ergonomics evaluation of retail ice cream shops, including field and laboratory data collection, was conducted using a human:workplace model approach to ergonomics practice. The goal of the evaluation was to provide recommendations to enhance the health, safety, and productivity of shop employees. Active and passive surveillance and facility walk-throughs were used to guide the selection of analyses. A primary focus of the investigation was quantifying the task demands of scooping ice cream, which have not been documented in the literature. This goal was accomplished through the use of a custom-designed instrumented ice cream scoop. Data were collected at an ice cream shop under typical conditions, while the laboratory experiment investigated task demands of ice cream scooping over a range of realistic temperatures. Manual materials handling task analyses and anthropometric evaluations comprised the majority of other analyses performed. Recommendations are presented that are applicable to the operation of retail ice cream shops that serve hard (i.e., scooped) ice cream.

Video framerate, resolution and grayscale tradeoffs for undersea telemanipulator

NASA Technical Reports Server (NTRS)

Ranadive, V.; Sheridan, T. B.

1981-01-01

The product of Frame Rate (F) in frames per second, Resolution (R) in total pixels and grayscale in bits (G) equals the transmission band rate in bits per second. Thus for a fixed channel capacity there are tradeoffs between F, R and G in the actual sampling of the picture for a particular manual control task in the present case remote undersea manipulation. A manipulator was used in the MASTER/SLAVE mode to study these tradeoffs. Images were systematically degraded from 28 frames per second, 128 x 128 pixels and 16 levels (4 bits) grayscale, with various FRG combinations constructed from a real-time digitized (charge-injection) video camera. It was found that frame rate, resolution and grayscale could be independently reduced without preventing the operator from accomplishing his/her task. Threshold points were found beyond which degradation would prevent any successful performance. A general conclusion is that a well trained operator can perform familiar remote manipulator tasks with a considerably degrade picture, down to 50 K bits/ sec.

Genetic algorithm based task reordering to improve the performance of batch scheduled massively parallel scientific applications

DOE PAGES

Sankaran, Ramanan; Angel, Jordan; Brown, W. Michael

2015-04-08

The growth in size of networked high performance computers along with novel accelerator-based node architectures has further emphasized the importance of communication efficiency in high performance computing. The world's largest high performance computers are usually operated as shared user facilities due to the costs of acquisition and operation. Applications are scheduled for execution in a shared environment and are placed on nodes that are not necessarily contiguous on the interconnect. Furthermore, the placement of tasks on the nodes allocated by the scheduler is sub-optimal, leading to performance loss and variability. Here, we investigate the impact of task placement on themore » performance of two massively parallel application codes on the Titan supercomputer, a turbulent combustion flow solver (S3D) and a molecular dynamics code (LAMMPS). Benchmark studies show a significant deviation from ideal weak scaling and variability in performance. The inter-task communication distance was determined to be one of the significant contributors to the performance degradation and variability. A genetic algorithm-based parallel optimization technique was used to optimize the task ordering. This technique provides an improved placement of the tasks on the nodes, taking into account the application's communication topology and the system interconnect topology. As a result, application benchmarks after task reordering through genetic algorithm show a significant improvement in performance and reduction in variability, therefore enabling the applications to achieve better time to solution and scalability on Titan during production.« less

Optimal dynamic voltage scaling for wireless sensor nodes with real-time constraints

NASA Astrophysics Data System (ADS)

Cassandras, Christos G.; Zhuang, Shixin

2005-11-01

Sensors are increasingly embedded in manufacturing systems and wirelessly networked to monitor and manage operations ranging from process and inventory control to tracking equipment and even post-manufacturing product monitoring. In building such sensor networks, a critical issue is the limited and hard to replenish energy in the devices involved. Dynamic voltage scaling is a technique that controls the operating voltage of a processor to provide desired performance while conserving energy and prolonging the overall network's lifetime. We consider such power-limited devices processing time-critical tasks which are non-preemptive, aperiodic and have uncertain arrival times. We treat voltage scaling as a dynamic optimization problem whose objective is to minimize energy consumption subject to hard or soft real-time execution constraints. In the case of hard constraints, we build on prior work (which engages a voltage scaling controller at task completion times) by developing an intra-task controller that acts at all arrival times of incoming tasks. We show that this optimization problem can be decomposed into two simpler ones whose solution leads to an algorithm that does not actually require solving any nonlinear programming problems. In the case of soft constraints, this decomposition must be partly relaxed, but it still leads to a scalable (linear in the number of tasks) algorithm. Simulation results are provided to illustrate performance improvements in systems with intra-task controllers compared to uncontrolled systems or those using inter-task control.

Personnel reliability impact on petrochemical facilities monitoring system's failure skipping probability

NASA Astrophysics Data System (ADS)

Kostyukov, V. N.; Naumenko, A. P.

2017-08-01

The paper dwells upon urgent issues of evaluating impact of actions conducted by complex technological systems operators on their safe operation considering application of condition monitoring systems for elements and sub-systems of petrochemical production facilities. The main task for the research is to distinguish factors and criteria of monitoring system properties description, which would allow to evaluate impact of errors made by personnel on operation of real-time condition monitoring and diagnostic systems for machinery of petrochemical facilities, and find and objective criteria for monitoring system class, considering a human factor. On the basis of real-time condition monitoring concepts of sudden failure skipping risk, static and dynamic error, monitoring systems, one may solve a task of evaluation of impact that personnel's qualification has on monitoring system operation in terms of error in personnel or operators' actions while receiving information from monitoring systems and operating a technological system. Operator is considered as a part of the technological system. Although, personnel's behavior is usually a combination of the following parameters: input signal - information perceiving, reaction - decision making, response - decision implementing. Based on several researches on behavior of nuclear powers station operators in USA, Italy and other countries, as well as on researches conducted by Russian scientists, required data on operator's reliability were selected for analysis of operator's behavior at technological facilities diagnostics and monitoring systems. The calculations revealed that for the monitoring system selected as an example, the failure skipping risk for the set values of static (less than 0.01) and dynamic (less than 0.001) errors considering all related factors of data on reliability of information perception, decision-making, and reaction fulfilled is 0.037, in case when all the facilities and error probability are under control - not more than 0.027. In case when only pump and compressor units are under control, the failure skipping risk is not more than 0.022, when the probability of error in operator's action is not more than 0.011. The work output shows that on the basis of the researches results an assessment of operators' reliability can be made in terms of almost any kind of production, but considering only technological capabilities, since operators' psychological and general training considerable vary in different production industries. Using latest technologies of engineering psychology and design of data support systems, situation assessment systems, decision-making and responding system, as well as achievement in condition monitoring in various production industries one can evaluate hazardous condition skipping risk probability considering static, dynamic errors and human factor.

Comparison of Multiobjective Evolutionary Algorithms for Operations Scheduling under Machine Availability Constraints

PubMed Central

Frutos, M.; Méndez, M.; Tohmé, F.; Broz, D.

2013-01-01

Many of the problems that arise in production systems can be handled with multiobjective techniques. One of those problems is that of scheduling operations subject to constraints on the availability of machines and buffer capacity. In this paper we analyze different Evolutionary multiobjective Algorithms (MOEAs) for this kind of problems. We consider an experimental framework in which we schedule production operations for four real world Job-Shop contexts using three algorithms, NSGAII, SPEA2, and IBEA. Using two performance indexes, Hypervolume and R2, we found that SPEA2 and IBEA are the most efficient for the tasks at hand. On the other hand IBEA seems to be a better choice of tool since it yields more solutions in the approximate Pareto frontier. PMID:24489502

Job task characteristics of Australian emergency services volunteers during search and rescue operations.

PubMed

Silk, Aaron; Lenton, Gavin; Savage, Robbie; Aisbett, Brad

2018-02-01

Search and rescue operations are necessary in locating, assisting and recovering individuals lost or in distress. In Australia, land-based search and rescue roles require a range of physically demanding tasks undertaken in dynamic and challenging environments. The aim of the current research was to identify and characterise the physically demanding tasks inherent to search and rescue operation personnel within Australia. These aims were met through a subjective job task analysis approach. In total, 11 criterion tasks were identified by personnel. These tasks were the most physically demanding, frequently occurring and operationally important tasks to these specialist roles. Muscular strength was the dominant fitness component for 7 of the 11 tasks. In addition to the discrete criterion tasks, an operational scenario was established. With the tasks and operational scenario identified, objective task analysis procedures can be undertaken so that practitioners can implement evidence-based strategies, such as physical selection procedures and task-based physical training programs, commensurate with the physical demands of search and rescue job roles. Practitioner Summary: The identification of physically demanding tasks amongst specialist emergency service roles predicates health and safety strategies which can be incorporated into organisations. Knowledge of physical task parameters allows employers to mitigate injury risk through the implementation of strategies modelled on the precise physical demands of the role.

JSpOC Cognitive Task Analysis

NASA Astrophysics Data System (ADS)

Aleva, D.; McCracken, J.

This paper will overview a Cognitive Task Analysis (CTA) of the tasks accomplished by space operators in the Combat Operations Division (COD) of the Joint Space Operations Center (JSpOC). The methodology used to collect data will be presented. The work was performed in support of the AFRL Space Situation Awareness Fusion Intelligent Research Environment (SAFIRE) effort. SAFIRE is a multi-directorate program led by Air Force Research Laboratory (AFRL), Space Vehicles Directorate (AFRL/RV) and supporting Future Long Term Challenge 2.6.5. It is designed to address research areas identified from completion of a Core Process 3 effort for Joint Space Operations Center (JSpOC). The report is intended to be a resource for those developing capability in support of SAFIRE, the Joint Functional Component Command (JFCC) Space Integrated Prototype (JSIP) User-Defined Operating Picture (UDOP), and other related projects. The report is under distribution restriction; our purpose here is to expose its existence to a wider audience so that qualified individuals may access it. The report contains descriptions of the organization, its most salient products, tools, and cognitive tasks. Tasks reported are derived from the data collected and presented at multiple levels of abstraction. Recommendations for leveraging the findings of the report are presented. The report contains a number of appendices that amplify the methodology, provide background or context support, and includes references in support of cognitive task methodology. In a broad sense, the CTA is intended to be the foundation for relevant, usable capability in support of space warfighters. It presents, at an unclassified level, introductory material to familiarize inquirers with the work of the COD; this is embedded in a description of the broader context of the other divisions of the JSpOC. It does NOT provide guidance for the development of Tactics, Techniques, and Procedures (TT&Ps) in the development of JSpOC processes. However, the TT&Ps are a part of the structure of work, and are, therefore, a factor in developing future capability. The authors gratefully acknowledge the cooperation and assistance from the warfighters at the JSpOC as well as the personnel of the JSpOC Capabilities Integration Office (JCIO). Their input to the process created the value of this effort.

Low cost silicon solar array project silicon materials task: Establishment of the feasibility of a process capable of low-cost, high volume production of silane (step 1) and the pyrolysis of silane to semiconductor-grade silicon (step 2)

NASA Technical Reports Server (NTRS)

Breneman, W. C.; Farrier, E. G.; Rexer, J.

1977-01-01

Extended operation of a small process-development unit routinely produced high quality silane in 97+% yield from dichlorosilane. The production rate was consistent with design loadings for the fractionating column and for the redistribution reactor. A glass fluid-bed reactor was constructed for room temperature operation. The behavior of a bed of silcon particles was observed as a function of various feedstocks, component configurations, and operating conditions. For operating modes other than spouting, the bed behaved in an erratic and unstable manner. A method was developed for casting molten silicon powder into crack-free solid pellets for process evaluation. The silicon powder was melted and cast into thin walled quartz tubes that sacrificially broke on cooling.

An anatomy of industrial robots and their controls

NASA Astrophysics Data System (ADS)

Luh, J. Y. S.

1983-02-01

The modernization of manufacturing facilities by means of automation represents an approach for increasing productivity in industry. The three existing types of automation are related to continuous process controls, the use of transfer conveyor methods, and the employment of programmable automation for the low-volume batch production of discrete parts. The industrial robots, which are defined as computer controlled mechanics manipulators, belong to the area of programmable automation. Typically, the robots perform tasks of arc welding, paint spraying, or foundary operation. One may assign a robot to perform a variety of job assignments simply by changing the appropriate computer program. The present investigation is concerned with an evaluation of the potential of the robot on the basis of its basic structure and controls. It is found that robots function well in limited areas of industry. If the range of tasks which robots can perform is to be expanded, it is necessary to provide multiple-task sensors, or special tooling, or even automatic tooling.

Automated plant, production management system

NASA Astrophysics Data System (ADS)

Aksenova, V. I.; Belov, V. I.

1984-12-01

The development of a complex of tasks for the operational management of production (OUP) within the framework of an automated system for production management (ASUP) shows that it is impossible to have effective computations without reliable initial information. The influence of many factors involving the production and economic activity of the entire enterprise upon the plan and course of production are considered. It is suggested that an adequate model should be available which covers all levels of the hierarchical system: workplace, section (bridgade), shop, enterprise, and the model should be incorporated into the technological sequence of performance and there should be provisions for an adequate man machine system.

Task-dependent signal variations in EEG error-related potentials for brain-computer interfaces.

PubMed

Iturrate, I; Montesano, L; Minguez, J

2013-04-01

A major difficulty of brain-computer interface (BCI) technology is dealing with the noise of EEG and its signal variations. Previous works studied time-dependent non-stationarities for BCIs in which the user's mental task was independent of the device operation (e.g., the mental task was motor imagery and the operational task was a speller). However, there are some BCIs, such as those based on error-related potentials, where the mental and operational tasks are dependent (e.g., the mental task is to assess the device action and the operational task is the device action itself). The dependence between the mental task and the device operation could introduce a new source of signal variations when the operational task changes, which has not been studied yet. The aim of this study is to analyse task-dependent signal variations and their effect on EEG error-related potentials. The work analyses the EEG variations on the three design steps of BCIs: an electrophysiology study to characterize the existence of these variations, a feature distribution analysis and a single-trial classification analysis to measure the impact on the final BCI performance. The results demonstrate that a change in the operational task produces variations in the potentials, even when EEG activity exclusively originated in brain areas related to error processing is considered. Consequently, the extracted features from the signals vary, and a classifier trained with one operational task presents a significant loss of performance for other tasks, requiring calibration or adaptation for each new task. In addition, a new calibration for each of the studied tasks rapidly outperforms adaptive techniques designed in the literature to mitigate the EEG time-dependent non-stationarities.

Task-dependent signal variations in EEG error-related potentials for brain-computer interfaces

NASA Astrophysics Data System (ADS)

Iturrate, I.; Montesano, L.; Minguez, J.

2013-04-01

Objective. A major difficulty of brain-computer interface (BCI) technology is dealing with the noise of EEG and its signal variations. Previous works studied time-dependent non-stationarities for BCIs in which the user’s mental task was independent of the device operation (e.g., the mental task was motor imagery and the operational task was a speller). However, there are some BCIs, such as those based on error-related potentials, where the mental and operational tasks are dependent (e.g., the mental task is to assess the device action and the operational task is the device action itself). The dependence between the mental task and the device operation could introduce a new source of signal variations when the operational task changes, which has not been studied yet. The aim of this study is to analyse task-dependent signal variations and their effect on EEG error-related potentials.Approach. The work analyses the EEG variations on the three design steps of BCIs: an electrophysiology study to characterize the existence of these variations, a feature distribution analysis and a single-trial classification analysis to measure the impact on the final BCI performance.Results and significance. The results demonstrate that a change in the operational task produces variations in the potentials, even when EEG activity exclusively originated in brain areas related to error processing is considered. Consequently, the extracted features from the signals vary, and a classifier trained with one operational task presents a significant loss of performance for other tasks, requiring calibration or adaptation for each new task. In addition, a new calibration for each of the studied tasks rapidly outperforms adaptive techniques designed in the literature to mitigate the EEG time-dependent non-stationarities.

Performance tasks for operator-skills research.

DOT National Transportation Integrated Search

1966-06-01

The selection, development, and operation of several tasks for use in skilled-operator-performance research are described. The tasks are intended, collectively, to sample a broad spectrum of abilities required by complex operator systems; individuall...

Cost Analysis of CATV Components. Final Report.

ERIC Educational Resources Information Center

Weinberg, Gary

A research study was conducted for the Office of Telecommunications Policy to determine the capital outlay and operating costs of community antenna television (CATV) systems. Six major tasks were undertaken: 1) the development of a body of technical information about CATV; 2) the production of a complete work breakdown structure; 3) a cost…

School Libraries Renewed

ERIC Educational Resources Information Center

Martin, Ann M.

2008-01-01

The United States no longer has a workforce dependent on operating machinery and performing repetitive tasks. Educators are therefore challenged to change the way students learn and to provide a workforce that is innovative and that has the ability to design new jobs. To do this, students must learn to be problem solvers, to create products that…

Process development for automated solar cell and module production. Task 4: Automated array assembly

NASA Technical Reports Server (NTRS)

Hagerty, J. J.

1981-01-01

The cell preparation station was installed in its new enclosure. Operation verification tests were performed. The detailed layout drawings of the automated lamination station were produced and construction began. All major and most minor components were delivered by vendors. The station framework was built and assembly of components begun.

Feasibility study of an Integrated Program for Aerospace-vehicle Design (IPAD) system. Volume 6: Implementation schedule, development costs, operational costs, benefit assessment, impact on company organization, spin-off assessment, phase 1, tasks 3 to 8

NASA Technical Reports Server (NTRS)

Garrocq, C. A.; Hurley, M. J.; Dublin, M.

1973-01-01

A baseline implementation plan, including alternative implementation approaches for critical software elements and variants to the plan, was developed. The basic philosophy was aimed at: (1) a progressive release of capability for three major computing systems, (2) an end product that was a working tool, (3) giving participation to industry, government agencies, and universities, and (4) emphasizing the development of critical elements of the IPAD framework software. The results of these tasks indicate an IPAD first release capability 45 months after go-ahead, a five year total implementation schedule, and a total developmental cost of 2027 man-months and 1074 computer hours. Several areas of operational cost increases were identified mainly due to the impact of additional equipment needed and additional computer overhead. The benefits of an IPAD system were related mainly to potential savings in engineering man-hours, reduction of design-cycle calendar time, and indirect upgrading of product quality and performance.

Sensor System Performance Evaluation and Benefits from the NPOESS Airborne Sounder Testbed-Interferometer (NAST-I)

NASA Technical Reports Server (NTRS)

Larar, A.; Zhou, D.; Smith, W.

2009-01-01

Advanced satellite sensors are tasked with improving global-scale measurements of the Earth's atmosphere, clouds, and surface to enable enhancements in weather prediction, climate monitoring, and environmental change detection. Validation of the entire measurement system is crucial to achieving this goal and thus maximizing research and operational utility of resultant data. Field campaigns employing satellite under-flights with well-calibrated FTS sensors aboard high-altitude aircraft are an essential part of this validation task. The National Polar-orbiting Operational Environmental Satellite System (NPOESS) Airborne Sounder Testbed-Interferometer (NAST-I) has been a fundamental contributor in this area by providing coincident high spectral/spatial resolution observations of infrared spectral radiances along with independently-retrieved geophysical products for comparison with like products from satellite sensors being validated. This paper focuses on some of the challenges associated with validating advanced atmospheric sounders and the benefits obtained from employing airborne interferometers such as the NAST-I. Select results from underflights of the Aqua Atmospheric InfraRed Sounder (AIRS) and the Infrared Atmospheric Sounding Interferometer (IASI) obtained during recent field campaigns will be presented.

Composable Analytic Systems for next-generation intelligence analysis

NASA Astrophysics Data System (ADS)

DiBona, Phil; Llinas, James; Barry, Kevin

2015-05-01

Lockheed Martin Advanced Technology Laboratories (LM ATL) is collaborating with Professor James Llinas, Ph.D., of the Center for Multisource Information Fusion at the University at Buffalo (State of NY), researching concepts for a mixed-initiative associate system for intelligence analysts to facilitate reduced analysis and decision times while proactively discovering and presenting relevant information based on the analyst's needs, current tasks and cognitive state. Today's exploitation and analysis systems have largely been designed for a specific sensor, data type, and operational context, leading to difficulty in directly supporting the analyst's evolving tasking and work product development preferences across complex Operational Environments. Our interactions with analysts illuminate the need to impact the information fusion, exploitation, and analysis capabilities in a variety of ways, including understanding data options, algorithm composition, hypothesis validation, and work product development. Composable Analytic Systems, an analyst-driven system that increases flexibility and capability to effectively utilize Multi-INT fusion and analytics tailored to the analyst's mission needs, holds promise to addresses the current and future intelligence analysis needs, as US forces engage threats in contested and denied environments.

A tool for optimization of the production and user analysis on the Grid, C. Grigoras for the ALICE Collaboration

NASA Astrophysics Data System (ADS)

Grigoras, Costin; Carminati, Federico; Vladimirovna Datskova, Olga; Schreiner, Steffen; Lee, Sehoon; Zhu, Jianlin; Gheata, Mihaela; Gheata, Andrei; Saiz, Pablo; Betev, Latchezar; Furano, Fabrizio; Mendez Lorenzo, Patricia; Grigoras, Alina Gabriela; Bagnasco, Stefano; Peters, Andreas Joachim; Saiz Santos, Maria Dolores

2011-12-01

With the LHC and ALICE entering a full operation and production modes, the amount of Simulation and RAW data processing and end user analysis computational tasks are increasing. The efficient management of all these tasks, all of which have large differences in lifecycle, amounts of processed data and methods to analyze the end result, required the development and deployment of new tools in addition to the already existing Grid infrastructure. To facilitate the management of the large scale simulation and raw data reconstruction tasks, ALICE has developed a production framework called a Lightweight Production Manager (LPM). The LPM is automatically submitting jobs to the Grid based on triggers and conditions, for example after a physics run completion. It follows the evolution of the job and publishes the results on the web for worldwide access by the ALICE physicists. This framework is tightly integrated with the ALICE Grid framework AliEn. In addition to the publication of the job status, LPM is also allowing a fully authenticated interface to the AliEn Grid catalogue, to browse and download files, and in the near future will provide simple types of data analysis through ROOT plugins. The framework is also being extended to allow management of end user jobs.

FINAL TECHNICAL REPORT FOR FORESTRY BIOFUEL STATEWIDE COLLABORATION CENTER (MICHIGAN)

DOE Office of Scientific and Technical Information (OSTI.GOV)

LaCourt, Donna M.; Miller, Raymond O.; Shonnard, David R.

A team composed of scientists from Michigan State University (MSU) and Michigan Technological University (MTU) assembled to better understand, document, and improve systems for using forest-based biomass feedstocks in the production of energy products within Michigan. Work was funded by a grant (DE-EE-0000280) from the U.S. Department of Energy (DOE) and was administered by the Michigan Economic Development Corporation (MEDC). The goal of the project was to improve the forest feedstock supply infrastructure to sustainably provide woody biomass for biofuel production in Michigan over the long-term. Work was divided into four broad areas with associated objectives: • TASK A: Developmore » a Forest-Based Biomass Assessment for Michigan – Define forest-based feedstock inventory, availability, and the potential of forest-based feedstock to support state and federal renewable energy goals while maintaining current uses. • TASK B: Improve Harvesting, Processing and Transportation Systems – Identify and develop cost, energy, and carbon efficient harvesting, processing and transportation systems. • TASK C: Improve Forest Feedstock Productivity and Sustainability – Identify and develop sustainable feedstock production systems through the establishment and monitoring of a statewide network of field trials in forests and energy plantations. • TASK D: Engage Stakeholders – Increase understanding of forest biomass production systems for biofuels by a broad range of stakeholders. The goal and objectives of this research and development project were fulfilled with key model deliverables including: 1) The Forest Biomass Inventory System (Sub-task A1) of feedstock inventory and availability and, 2) The Supply Chain Model (Sub-task B2). Both models are vital to Michigan’s forest biomass industry and support forecasting delivered cost, as well as carbon and energy balance. All of these elements are important to facilitate investor, operational and policy decisions. All other sub-tasks supported the development of these two tools either directly or by building out supporting information in the forest biomass supply chain. Outreach efforts have, and are continuing to get these user friendly models and information to decision makers to support biomass feedstock supply chain decisions across the areas of biomass inventory and availability, procurement, harvest, forwarding, transportation and processing. Outreach will continue on the project website at http://www.michiganforestbiofuels.org/ and http://www.michiganwoodbiofuels.org/« less

A National Coordinating Center for Prehospital Trauma Research Funding Transfusion Using Stored Fresh Whole Blood

DTIC Science & Technology

2016-09-01

bank data base 28-30 5% Analyze blood bank data base 28-33 0% Other Major Tasks: Identification of communities in the UCLA catchment area 1-3 N/A...coagulopathy in real-time is underway. The Blood Bank is working to identify a pool of whole blood donors and incorporating the new product (FWB) in...Blood Bank , emergency Room, Trauma, Operating Room, Intensive Care Unit, etc) to coordinate and streamline standard operating procedures for the

Improvement of Productivity in TIG Welding Plant by Equipment Design in Orbit

NASA Astrophysics Data System (ADS)

Gnanavel, C.; Saravanan, R.; Chandrasekaran, M.; Jayakanth, J. J.

2017-03-01

Measurements and improvements are very indispensable task at all levels of management. Here some samples are, at operator level: Measuring operating parameters to ensure OEE (Overall Equipment Effectiveness) and measuring Q components performance to ensure quality, at supervisory level: measuring operator’s performance to ensure labour utility at managerial level: production and productivity measurements and at top level capital and capacity utilization. An often accepted statement is “Improvement is impossible without measurement”. Measurements often referred as observation. The case study was conducted at Government Boiler factory in India. The scientific approach followed for indentifying non value added activities. Personalised new equipment designed and installed to achieve productivity improvement of 85% for a day. The new equipment can serve 360o around its axis hence it simplified loading and unloading procedures as well as reduce their times and ensured effective space and time.

Evaluating a voice recognition system: finding the right product for your department.

PubMed

Freeh, M; Dewey, M; Brigham, L

2001-06-01

The Department of Radiology at the University of Utah Health Sciences Center has been in the process of transitioning from the traditional film-based department to a digital imaging department for the past 2 years. The department is now transitioning from the traditional method of dictating reports (dictation by radiologist to transcription to review and signing by radiologist) to a voice recognition system. The transition to digital operations will not be complete until we have the ability to directly interface the dictation process with the image review process. Voice recognition technology has advanced to the level where it can and should be an integral part of the new way of working in radiology and is an integral part of an efficient digital imaging department. The transition to voice recognition requires the task of identifying the product and the company that will best meet a department's needs. This report introduces the methods we used to evaluate the vendors and the products available as we made our purchasing decision. We discuss our evaluation method and provide a checklist that can be used by other departments to assist with their evaluation process. The criteria used in the evaluation process fall into the following major categories: user operations, technical infrastructure, medical dictionary, system interfaces, service support, cost, and company strength. Conclusions drawn from our evaluation process will be detailed, with the intention being to shorten the process for others as they embark on a similar venture. As more and more organizations investigate the many products and services that are now being offered to enhance the operations of a radiology department, it becomes increasingly important that solid methods are used to most effectively evaluate the new products. This report should help others complete the task of evaluating a voice recognition system and may be adaptable to other products as well.

Energy Supply- Production of Fuel from Agricultural and Animal Waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gabriel Miller

2009-03-25

The Society for Energy and Environmental Research (SEER) was funded in March 2004 by the Department of Energy, under grant DE-FG-36-04GO14268, to produce a study, and oversee construction and implementation, for the thermo-chemical production of fuel from agricultural and animal waste. The grant focuses on the Changing World Technologies (CWT) of West Hempstead, NY, thermal conversion process (TCP), which converts animal residues and industrial food processing biproducts into fuels, and as an additional product, fertilizers. A commercial plant was designed and built by CWT, partially using grant funds, in Carthage, Missouri, to process animal residues from a nearby turkey processingmore » plant. The DOE sponsored program consisted of four tasks. These were: Task 1 Optimization of the CWT Plant in Carthage - This task focused on advancing and optimizing the process plant operated by CWT that converts organic waste to fuel and energy. Task 2 Characterize and Validate Fuels Produced by CWT - This task focused on testing of bio-derived hydrocarbon fuels from the Carthage plant in power generating equipment to determine the regulatory compliance of emissions and overall performance of the fuel. Task 3 Characterize Mixed Waste Streams - This task focused on studies performed at Princeton University to better characterize mixed waste incoming streams from animal and vegetable residues. Task 4 Fundamental Research in Waste Processing Technologies - This task focused on studies performed at the Massachusetts Institute of Technology (MIT) on the chemical reformation reaction of agricultural biomass compounds in a hydrothermal medium. Many of the challenges to optimize, improve and perfect the technology, equipment and processes in order to provide an economically viable means of creating sustainable energy were identified in the DOE Stage Gate Review, whose summary report was issued on July 30, 2004. This summary report appears herein as Appendix 1, and the findings of the report formed the basis for much of the subsequent work under the grant. An explanation of the process is presented as well as the completed work on the four tasks.« less

Task-selective memory effects for successfully implemented encoding strategies.

PubMed

Leshikar, Eric D; Duarte, Audrey; Hertzog, Christopher

2012-01-01

Previous behavioral evidence suggests that instructed strategy use benefits associative memory formation in paired associate tasks. Two such effective encoding strategies--visual imagery and sentence generation--facilitate memory through the production of different types of mediators (e.g., mental images and sentences). Neuroimaging evidence suggests that regions of the brain support memory reflecting the mental operations engaged at the time of study. That work, however, has not taken into account self-reported encoding task success (i.e., whether participants successfully generated a mediator). It is unknown, therefore, whether task-selective memory effects specific to each strategy might be found when encoding strategies are successfully implemented. In this experiment, participants studied pairs of abstract nouns under either visual imagery or sentence generation encoding instructions. At the time of study, participants reported their success at generating a mediator. Outside of the scanner, participants further reported the quality of the generated mediator (e.g., images, sentences) for each word pair. We observed task-selective memory effects for visual imagery in the left middle occipital gyrus, the left precuneus, and the lingual gyrus. No such task-selective effects were observed for sentence generation. Intriguingly, activity at the time of study in the left precuneus was modulated by the self-reported quality (vividness) of the generated mental images with greater activity for trials given higher ratings of quality. These data suggest that regions of the brain support memory in accord with the encoding operations engaged at the time of study.

Task-Selective Memory Effects for Successfully Implemented Encoding Strategies

PubMed Central

Leshikar, Eric D.; Duarte, Audrey; Hertzog, Christopher

2012-01-01

Previous behavioral evidence suggests that instructed strategy use benefits associative memory formation in paired associate tasks. Two such effective encoding strategies–visual imagery and sentence generation–facilitate memory through the production of different types of mediators (e.g., mental images and sentences). Neuroimaging evidence suggests that regions of the brain support memory reflecting the mental operations engaged at the time of study. That work, however, has not taken into account self-reported encoding task success (i.e., whether participants successfully generated a mediator). It is unknown, therefore, whether task-selective memory effects specific to each strategy might be found when encoding strategies are successfully implemented. In this experiment, participants studied pairs of abstract nouns under either visual imagery or sentence generation encoding instructions. At the time of study, participants reported their success at generating a mediator. Outside of the scanner, participants further reported the quality of the generated mediator (e.g., images, sentences) for each word pair. We observed task-selective memory effects for visual imagery in the left middle occipital gyrus, the left precuneus, and the lingual gyrus. No such task-selective effects were observed for sentence generation. Intriguingly, activity at the time of study in the left precuneus was modulated by the self-reported quality (vividness) of the generated mental images with greater activity for trials given higher ratings of quality. These data suggest that regions of the brain support memory in accord with the encoding operations engaged at the time of study. PMID:22693593

Transition from Research to Operations: Assessing Value of Experimental Forecast Products within the NWSFO Environment

NASA Technical Reports Server (NTRS)

Lapenta, William M.; Wohlman, Richard; Bradshaw, Tom; Burks, Jason; Jedlovec, Gary; Goodman, Steve; Darden, Chris; Meyer, Paul

2003-01-01

The NASA Short-term Prediction Research and Transition (SPoRT) Center seeks to accelerate the infusion of NASA Earth Science Enterprise (ESE) observations, data assimilation and modeling research into NWS forecast operations and decision-making. To meet long-term program expectations, it is not sufficient simply to give forecasters sophisticated workstations or new forecast products without fully assessing the ways in which they will be utilized. Close communication must be established between the research and operational communities so that developers have a complete understanding of user needs. In turn, forecasters must obtain a more comprehensive knowledge of the modeling and sensing tools available to them. A major goal of the SPoRT Program is to develop metrics and conduct assessment studies with NWS forecasters to evaluate the impacts and benefits of ESE experimental products on forecast skill. At a glance the task seems relatively straightforward. However, performing assessment of experimental products in an operational environment is demanding. Given the tremendous time constraints placed on NWS forecasters, it is imperative that forecaster input be obtained in a concise unobtrusive manor. Great care must also be taken to ensure that forecasters understand their participation will eventually benefit them and WFO operations in general. Two requirements of the assessment plan developed under the SPoRT activity are that it 1) Can be implemented within the WFO environment; and 2) Provide tangible results for BOTH the research and operational communities. Supplemental numerical quantitative precipitation forecasts (QPF) were chosen as the first experimental SPoRT product to be evaluated during a Pilot Assessment Program conducted 1 May 2003 within the Huntsville AL National Weather Service Forecast Office. Forecast time periods were broken up into six- hour bins ranging from zero to twenty-four hours. Data were made available for display in AWIPS on an operational basis so they could be efficiently incorporated into the forecast process. The methodology used to assess the value of experimental QPFs compared to available operational products is best described as a three-tier approach involving both forecasters and research scientists. Tier-one is a web-based survey completed by duty forecasters on the aviation and public desks. The survey compiles information on how the experimental product was used in the forecast decision making process. Up to 6 responses per twenty-four hours can be compiled during a precipitation event. Tier-two consists of an event post mortem and experimental product assessment performed daily by the NASA/NWS Liaison. Tier-three is a detailed breakdown/analysis of specific events targeted by either the NWS SO0 or SPoRT team members. The task is performed by both NWS and NASA research scientists and may be conducted once every couple of months. The findings from the Pilot Assessment Program will be reported at the meeting.

Considerations for human-machine interfaces in tele-operations

NASA Technical Reports Server (NTRS)

Newport, Curt

1991-01-01

Numerous factors impact on the efficiency of tele-operative manipulative work. Generally, these are related to the physical environment of the tele-operator and how he interfaces with robotic control consoles. The capabilities of the operator can be influenced by considerations such as temperature, eye strain, body fatigue, and boredom created by repetitive work tasks. In addition, the successful combination of man and machine will, in part, be determined by the configuration of the visual and physical interfaces available to the teleoperator. The design and operation of system components such as full-scale and mini-master manipulator controllers, servo joysticks, and video monitors will have a direct impact on operational efficiency. As a result, the local environment and the interaction of the operator with the robotic control console have a substantial effect on mission productivity.

Space station definition and preliminary design, WP-01. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

Lenda, J. A.

1987-01-01

System activities are summarized and an overview of the system level engineering tasks performed are provided. Areas discussed include requirements, system test and verification, the advanced development plan, customer accommodations, software, growth, productivity, operations, product assurance and metrication. The hardware element study results are summarized. Overviews of recommended configurations are provided for the core module, the USL, the logistics elements, the propulsion subsystems, reboost, vehicle accommodations, and the smart front end. A brief overview is provided for costing activities.

Space transfer vehicle concepts and requirements study. Volume 3: Program cost estimates. Book 2: WBS and dictionary

NASA Technical Reports Server (NTRS)

Peffley, A. F.

1991-01-01

This document describes the products and services to be developed, tested, produced, and operated for the Space Transfer Vehicle (STV) Program. The Work Breakdown Structure (WBS) and WBS Dictionary are program management tools used to catalog, account by task, and summarize work packages of a space system program. The products or services to be delivered or accomplished during the STV C/D phase are the primary focus of this work breakdown structure document.

MM III/Mk 12A Reentry Vehicle Carbon/Carbon Nosetip Production Program.

DTIC Science & Technology

1980-05-28

MI IlI/MIK 12A REENTRY VEHICLE CARBON/CARBON NOSETIP PRODUCTION PROGRAM CRITICAL ITEM CONI.<OL PLN 1.0 INTRODUCTION 1. 1 PURPOS’ The purpose of...the basis of its proven technological and pruduction capability in Fine-Weave Pierced Fabric (FWPF) Carbon/Carbocn Nosetips. Avco in turn has awarded...are inspected prior to the acceptanicc of the part. Each operator and/or inspector assig ;ned to do a specific task has all the required infornmation

Supporting the future nuclear workforce with computer-based procedures

DOE PAGES

Oxstrand, Johanna; Le Blanc, Katya

2016-05-01

Here we see that computer-based tools have dramatically increased ease and efficiency of everyday tasks. Gone are the days of paging through a paper catalog, transcribing product numbers, and calculating totals. Today, a consumer can find a product online with a simple search engine, and then purchase it in a matter of a few clicks. Paper catalogs have their place, but it is hard to imagine life without on-line shopping sites. All tasks conducted in a nuclear power plant are guided by procedures, which helps ensure safe and reliable operation of the plants. One prominent goal of the nuclear industrymore » is to minimize the risk of human errors. To achieve this goal one has to ensure tasks are correctly and consistently executed. This is partly achieved by training and by a structured approach to task execution, which is provided by procedures and work instructions. Procedures are used in the nuclear industry to direct workers' actions in a proper sequence. The governing idea is to minimize the reliance on memory and choices made in the field. However, the procedure document may not contain sufficient information to successfully complete the task. Therefore, the worker might have to carry additional documents such as turnover sheets, operation experience, drawings, and other procedures to the work site. The nuclear industry is operated with paper procedures like paper catalogs of the past. A field worker may carry a large stack of documents needed to complete a task to the field. Even though the paper process has helped keep the industry safe for decades, there are limitations to using paper. Paper procedures are static (i.e., the content does not change after the document is printed), difficult to search, and rely heavily on the field worker’s situational awareness and ability to consistently meet the high expectation of human performance excellence. With computer-based procedures (CBPs) that stack of papers may be reduced to the size of a small tablet or even a smart phone. Instead of manually matching equipment identification numbers listed in the procedure with the number on the physical equipment the field worker can simply scan a barcode to ensure the correct valve is opened while simultaneously creating a record. Instead of navigating through a maze of cross-references, CBPs enable intelligent work path navigation which accounts for past decisions and observation, thereby enabling more efficient and safe task completion.« less

Supporting the future nuclear workforce with computer-based procedures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oxstrand, Johanna; Le Blanc, Katya

Here we see that computer-based tools have dramatically increased ease and efficiency of everyday tasks. Gone are the days of paging through a paper catalog, transcribing product numbers, and calculating totals. Today, a consumer can find a product online with a simple search engine, and then purchase it in a matter of a few clicks. Paper catalogs have their place, but it is hard to imagine life without on-line shopping sites. All tasks conducted in a nuclear power plant are guided by procedures, which helps ensure safe and reliable operation of the plants. One prominent goal of the nuclear industrymore » is to minimize the risk of human errors. To achieve this goal one has to ensure tasks are correctly and consistently executed. This is partly achieved by training and by a structured approach to task execution, which is provided by procedures and work instructions. Procedures are used in the nuclear industry to direct workers' actions in a proper sequence. The governing idea is to minimize the reliance on memory and choices made in the field. However, the procedure document may not contain sufficient information to successfully complete the task. Therefore, the worker might have to carry additional documents such as turnover sheets, operation experience, drawings, and other procedures to the work site. The nuclear industry is operated with paper procedures like paper catalogs of the past. A field worker may carry a large stack of documents needed to complete a task to the field. Even though the paper process has helped keep the industry safe for decades, there are limitations to using paper. Paper procedures are static (i.e., the content does not change after the document is printed), difficult to search, and rely heavily on the field worker’s situational awareness and ability to consistently meet the high expectation of human performance excellence. With computer-based procedures (CBPs) that stack of papers may be reduced to the size of a small tablet or even a smart phone. Instead of manually matching equipment identification numbers listed in the procedure with the number on the physical equipment the field worker can simply scan a barcode to ensure the correct valve is opened while simultaneously creating a record. Instead of navigating through a maze of cross-references, CBPs enable intelligent work path navigation which accounts for past decisions and observation, thereby enabling more efficient and safe task completion.« less

Operations Data Files, driving force behind International Space Station operations

NASA Astrophysics Data System (ADS)

Hoppenbrouwers, Tom; Ferra, Lionel; Markus, Michael; Wolff, Mikael

2017-09-01

Almost all tasks performed by the astronauts on-board the International Space Station (ISS) and by ground controllers in Mission Control Centre, from operation and maintenance of station systems to the execution of scientific experiments or high risk visiting vehicles docking manoeuvres, would not be possible without Operations Data Files (ODF). ODFs are the User Manuals of the Space Station and have multiple faces, going from traditional step-by-step procedures, scripts, cue cards, over displays, to software which guides the crew through the execution of certain tasks. Those key operational documents are standardized as they are used on-board the Space Station by an international crew constantly changing every 3 months. Furthermore this harmonization effort is paramount for consistency as the crew moves from one element to another in a matter of seconds, and from one activity to another. On ground, a significant large group of experts from all International Partners drafts, prepares reviews and approves on a daily basis all Operations Data Files, ensuring their timely availability on-board the ISS for all activities. Unavailability of these operational documents will halt the conduct of experiments or cancel milestone events. This paper will give an insight in the ground preparation work for the ODFs (with a focus on ESA ODF processes) and will present an overview on ODF formats and their usage within the ISS environment today and show how vital they are. Furthermore the focus will be on the recently implemented ODF features, which significantly ease the use of this documentation and improve the efficiency of the astronauts performing the tasks. Examples are short video demonstrations, interactive 3D animations, Execute Tailored Procedures (XTP-versions), tablet products, etc.

Cost Study of Educational Media Systems and Their Equipment Components. Volume II, Technical Report. Final Report.

ERIC Educational Resources Information Center

General Learning Corp., Washington, DC.

A common instructional task and a set of educational environments are hypothesized for analysis of media cost data. The analytic structure may be conceptulized as a three-dimensional matrix: the first vector separates costs into production, distribution, and reception; the second vector delineates capital (initial) and operating (annual) costs;…

Using Technology's Internet Resources in Algebra 1

ERIC Educational Resources Information Center

Crespo, Irma S. Z. B.

2009-01-01

Technology is a means that makes work or tasks easy, efficient, and operative. A more encompassing definition refers to it "as the tools created by human knowledge of how to combine resources to produce desired products, to solve problems, fulfill needs, or satisfy wants" (Koehler and Mishra. 2008:5). It can either be contrivances of tradition or…

Thermal analysis elements of liquefied gas storage tanks

NASA Astrophysics Data System (ADS)

Yanvarev, I. A.; Krupnikov, A. V.

2017-08-01

Tasks of solving energy and resource efficient usage problems, both for oil producing companies and for companies extracting and transporting natural gas, are associated with liquefied petroleum gas technology development. Improving the operation efficiency of liquefied products storages provides for conducting structural, functional, and appropriate thermal analysis of tank parks in the general case as complex dynamic thermal systems.

Designing Interaction as a Learning Process: Supporting Users' Domain Knowledge Development in Interaction

ERIC Educational Resources Information Center

Choi, Jung-Min

2010-01-01

The primary concern in current interaction design is focused on how to help users solve problems and achieve goals more easily and efficiently. While users' sufficient knowledge acquisition of operating a product or system is considered important, their acquisition of problem-solving knowledge in the task domain has largely been disregarded. As a…

Rules for Adaptive Learning and Assistance on the Shop Floor

ERIC Educational Resources Information Center

Ullrich, Carsten

2016-01-01

Today's shop floor, the area of a factory where operatives assemble products, is a complex and demanding work environment. The employed and produced technology becomes ever more complex, and employees are responsible for an increasing amount of tasks. As a consequence, the employee is under constant pressure to solve problems occurring on the shop…

Tools to Support Human Factors and Systems Engineering Interactions During Early Analysis

NASA Technical Reports Server (NTRS)

Thronesbery, Carroll; Malin, Jane T.; Holden, Kritina; Smith, Danielle Paige

2005-01-01

We describe an approach and existing software tool support for effective interactions between human factors engineers and systems engineers in early analysis activities during system acquisition. We examine the tasks performed during this stage, emphasizing those tasks where system engineers and human engineers interact. The Concept of Operations (ConOps) document is an important product during this phase, and particular attention is paid to its influences on subsequent acquisition activities. Understanding this influence helps ConOps authors describe a complete system concept that guides subsequent acquisition activities. We identify commonly used system engineering and human engineering tools and examine how they can support the specific tasks associated with system definition. We identify possible gaps in the support of these tasks, the largest of which appears to be creating the ConOps document itself. Finally, we outline the goals of our future empirical investigations of tools to support system concept definition.

Tools to Support Human Factors and Systems Engineering Interactions During Early Analysis

NASA Technical Reports Server (NTRS)

Thronesbery, Carroll; Malin, Jane T.; Holden, Kritina; Smith, Danielle Paige

2006-01-01

We describe an approach and existing software tool support for effective interactions between human factors engineers and systems engineers in early analysis activities during system acquisition. We examine the tasks performed during this stage, emphasizing those tasks where system engineers and human engineers interact. The Concept of Operations (ConOps) document is an important product during this phase, and particular attention is paid to its influences on subsequent acquisition activities. Understanding this influence helps ConOps authors describe a complete system concept that guides subsequent acquisition activities. We identify commonly used system engineering and human engineering tools and examine how they can support the specific tasks associated with system definition. We identify possible gaps in the support of these tasks, the largest of which appears to be creating the ConOps document itself. Finally, we outline the goals of our future empirical investigations of tools to support system concept definition.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The study was funded by the U.S. Trade and Development Agency on behalf of the Municipality of Greater Istanbul. Summarized in the report are the results of two feasibility studies. The first, referred to as Task No. 6, was conducted to develop technical specifications and terms of reference for the design, construction, and operation of a landfill gas-to-electrical energy project at a new European landfill. The second, the Umraniye Dump Stabilization Project (Task No. 7), addresses the stabilization measures necessary to prevent future failure at the Umraniye dump site. The summary report is divided into the following sections: Task No.more » 6-(1) Terms of reference for the DBOT Contract; (2) Estimated Value of the DBOT Contracts; (3) Foreign Trade Potential; (4) Project Financing; Task No. 7-(1) Results of the Services; (2) Foreign Trade Potential. Also included is a list of U.S. solid waste firms, landfill gas recovery and energy generation firms, and equipment and product suppliers.« less

Process development for automated solar cell and module production. Task 4: Automated array assembly

NASA Technical Reports Server (NTRS)

Hagerty, J. J.

1981-01-01

Progress in the development of automated solar cell and module production is reported. The unimate robot is programmed for the final 35 cell pattern to be used in the fabrication of the deliverable modules. The mechanical construction of the automated lamination station and final assembly station phases are completed and the first operational testing is underway. The final controlling program is written and optimized. The glass reinforced concrete (GRC) panels to be used for testing and deliverables are in production. Test routines are grouped together and defined to produce the final control program.

Measures and Interpretations of Vigilance Performance: Evidence Against the Detection Criterion

NASA Technical Reports Server (NTRS)

Balakrishnan, J. D.

1998-01-01

Operators' performance in a vigilance task is often assumed to depend on their choice of a detection criterion. When the signal rate is low this criterion is set high, causing the hit and false alarm rates to be low. With increasing time on task the criterion presumably tends to increase even further, thereby further decreasing the hit and false alarm rates. Virtually all of the empirical evidence for this simple interpretation is based on estimates of the bias measure Beta from signal detection theory. In this article, I describe a new approach to studying decision making that does not require the technical assumptions of signal detection theory. The results of this new analysis suggest that the detection criterion is never biased toward either response, even when the signal rate is low and the time on task is long. Two modifications of the signal detection theory framework are considered to account for this seemingly paradoxical result. The first assumes that the signal rate affects the relative sizes of the variances of the information distributions; the second assumes that the signal rate affects the logic of the operator's stopping rule. Actual or potential applications of this research include the improved training and performance assessment of operators in areas such as product quality control, air traffic control, and medical and clinical diagnosis.

Kinematic path planning for space-based robotics

NASA Astrophysics Data System (ADS)

Seereeram, Sanjeev; Wen, John T.

1998-01-01

Future space robotics tasks require manipulators of significant dexterity, achievable through kinematic redundancy and modular reconfigurability, but with a corresponding complexity of motion planning. Existing research aims for full autonomy and completeness, at the expense of efficiency, generality or even user friendliness. Commercial simulators require user-taught joint paths-a significant burden for assembly tasks subject to collision avoidance, kinematic and dynamic constraints. Our research has developed a Kinematic Path Planning (KPP) algorithm which bridges the gap between research and industry to produce a powerful and useful product. KPP consists of three key components: path-space iterative search, probabilistic refinement, and an operator guidance interface. The KPP algorithm has been successfully applied to the SSRMS for PMA relocation and dual-arm truss assembly tasks. Other KPP capabilities include Cartesian path following, hybrid Cartesian endpoint/intermediate via-point planning, redundancy resolution and path optimization. KPP incorporates supervisory (operator) input at any detail to influence the solution, yielding desirable/predictable paths for multi-jointed arms, avoiding obstacles and obeying manipulator limits. This software will eventually form a marketable robotic planner suitable for commercialization in conjunction with existing robotic CAD/CAM packages.

Performance impact of mutation operators of a subpopulation-based genetic algorithm for multi-robot task allocation problems.

PubMed

Liu, Chun; Kroll, Andreas

2016-01-01

Multi-robot task allocation determines the task sequence and distribution for a group of robots in multi-robot systems, which is one of constrained combinatorial optimization problems and more complex in case of cooperative tasks because they introduce additional spatial and temporal constraints. To solve multi-robot task allocation problems with cooperative tasks efficiently, a subpopulation-based genetic algorithm, a crossover-free genetic algorithm employing mutation operators and elitism selection in each subpopulation, is developed in this paper. Moreover, the impact of mutation operators (swap, insertion, inversion, displacement, and their various combinations) is analyzed when solving several industrial plant inspection problems. The experimental results show that: (1) the proposed genetic algorithm can obtain better solutions than the tested binary tournament genetic algorithm with partially mapped crossover; (2) inversion mutation performs better than other tested mutation operators when solving problems without cooperative tasks, and the swap-inversion combination performs better than other tested mutation operators/combinations when solving problems with cooperative tasks. As it is difficult to produce all desired effects with a single mutation operator, using multiple mutation operators (including both inversion and swap) is suggested when solving similar combinatorial optimization problems.

Mars surface-based factory: Computer control of a water treatment system to support a space colony on Mars

NASA Technical Reports Server (NTRS)

Brice, R.; Mosley, J.; Willis, D.; Coleman, K.; Martin, C.; Shelby, L.; Kelley, U.; Renfro, E.; Griffith, G.; Warsame, A.

1989-01-01

In a continued effort to design a surface-based factory on Mars for the production of oxygen and water, the Design Group at Prairie View A&M University made a preliminary study of the surface and atmospheric composition on Mars and determined the mass densities of the various gases in the martian atmosphere. Based on the initial studies, the design group determined oxygen and water to be the two products that could be produced economically under the martian conditions. Studies were also made on present production techniques to obtain water and oxygen. Analyses were made to evaluate the current methods of production that were adaptable to the martian conditions. The detailed report was contained in an Interim Report submitted to NASA/USRA in Aug. of 1986. Even though the initial effort was the production of oxygen and water, we found it necessary to produce some diluted gases that can be mixed with oxygen to constitute 'breathable' air. In Phase 2--Task 1A, the Prairie View A&M University team completed the conceptual design of a breathable-air manufacturing system, a means of drilling for underground water, and storage of water for future use. The design objective of the team for the 1987-1988 academic year was the conceptual design of an integrated system for the supply of quality water for biological consumption, farming, and residential and industrial use. The design has also been completed. Phase 2--Task 1C is the present task for the Prairie View Design Team. This is a continuation of the previous task, and the continuation of this effort is the investigation into the extraction of water from beneath the surface and an alternative method of extraction from ice formations on the surface of Mars if accessible. In addition to investigation of water extraction, a system for computer control of extraction and treatment was developed with emphasis on fully automated control with robotic repair and maintenance. It is expected that oxygen- and water-producing plants on Mars will be limited in the amount of human control that will be available to operate large and/or isolated plants. Therefore, it is imperative that computers be integrated into plant operation with the capability to maintain life support systems and analyze and replace defective parts or systems with no human interface.

Mobilizable RDF/d-RDF burning program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Niemann, K.; Campbell, J.

1982-03-01

The Mobilizable RDF/d-RDF Burning Program was conceived to promote the utilization of refuse-derived fuels (RDF) as a supplement to existing fossil fuel sources in industrial-sized boilers. The program explores the design, development, and eventual construction of densified-RDF (d-RDF) for use in boiler combustion testing as a supplement to stoker coal or wood wastes. The equipment would be mounted on trailers and assembled and operated at preselected sites throughout the country where approximately 750 tons of RDF would be produced and test burned in a local boiler. The equipment, to include a transportable RDF boiler metering and feed system, would thenmore » be moved and operated at two to three test sites annually. The program is intended to encourage the construction of permanent resource recovery facilities by involving local waste handling groups in operating the equipment and producing fuel, and potential local fuel users in testing the fuel in their boilers. The Mobilizable Program was developed from two separate tasks. The first task developed the concept behind the program and defined its operational and organizational structure. The second task, a follow-up to the first, was intended principally to finalize test locations, develop equipment designs and specifications, and formalize a management program. This report summarizes the principal findings of both tasks. It identifies the criteria used to identify test locations, outlines the program's management structure, presents design and performance specifications for both the fuel production equipment and boiler fuel feed systems, and provides a detailed evaluation of the parameters involved in burning RDF in industrial-sized boilers. Final conclusions and recommendations identify problem areas encountered in the program, and discuss possible future directions for such a program.« less

SUMO: operation and maintenance management web tool for astronomical observatories

NASA Astrophysics Data System (ADS)

Mujica-Alvarez, Emma; Pérez-Calpena, Ana; García-Vargas, María. Luisa

2014-08-01

SUMO is an Operation and Maintenance Management web tool, which allows managing the operation and maintenance activities and resources required for the exploitation of a complex facility. SUMO main capabilities are: information repository, assets and stock control, tasks scheduler, executed tasks archive, configuration and anomalies control and notification and users management. The information needed to operate and maintain the system must be initially stored at the tool database. SUMO shall automatically schedule the periodical tasks and facilitates the searching and programming of the non-periodical tasks. Tasks planning can be visualized in different formats and dynamically edited to be adjusted to the available resources, anomalies, dates and other constrains that can arise during daily operation. SUMO shall provide warnings to the users notifying potential conflicts related to the required personal availability or the spare stock for the scheduled tasks. To conclude, SUMO has been designed as a tool to help during the operation management of a scientific facility, and in particular an astronomical observatory. This is done by controlling all operating parameters: personal, assets, spare and supply stocks, tasks and time constrains.

Human factors evaluation of remote afterloading brachytherapy. Volume 2, Function and task analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Callan, J.R.; Gwynne, J.W. III; Kelly, T.T.

1995-05-01

A human factors project on the use of nuclear by-product material to treat cancer using remotely operated afterloaders was undertaken by the Nuclear Regulatory Commission. The purpose of the project was to identify factors that contribute to human error in the system for remote afterloading brachytherapy (RAB). This report documents the findings from the first phase of the project, which involved an extensive function and task analysis of RAB. This analysis identified the functions and tasks in RAB, made preliminary estimates of the likelihood of human error in each task, and determined the skills needed to perform each RAB task.more » The findings of the function and task analysis served as the foundation for the remainder of the project, which evaluated four major aspects of the RAB system linked to human error: human-system interfaces; procedures and practices; training and qualifications of RAB staff; and organizational practices and policies. At its completion, the project identified and prioritized areas for recommended NRC and industry attention based on all of the evaluations and analyses.« less

Creation of system of computer-aided design for technological objects

NASA Astrophysics Data System (ADS)

Zubkova, T. M.; Tokareva, M. A.; Sultanov, N. Z.

2018-05-01

Due to the competition in the market of process equipment, its production should be flexible, retuning to various product configurations, raw materials and productivity, depending on the current market needs. This process is not possible without CAD (computer-aided design). The formation of CAD begins with planning. Synthesizing, analyzing, evaluating, converting operations, as well as visualization and decision-making operations, can be automated. Based on formal description of the design procedures, the design route in the form of an oriented graph is constructed. The decomposition of the design process, represented by the formalized description of the design procedures, makes it possible to make an informed choice of the CAD component for the solution of the task. The object-oriented approach allows us to consider the CAD as an independent system whose properties are inherited from the components. The first step determines the range of tasks to be performed by the system, and a set of components for their implementation. The second one is the configuration of the selected components. The interaction between the selected components is carried out using the CALS standards. The chosen CAD / CAE-oriented approach allows creating a single model, which is stored in the database of the subject area. Each of the integration stages is implemented as a separate functional block. The transformation of the CAD model into the model of the internal representation is realized by the block of searching for the geometric parameters of the technological machine, in which the XML-model of the construction is obtained on the basis of the feature method from the theory of image recognition. The configuration of integrated components is divided into three consecutive steps: configuring tasks, components, interfaces. The configuration of the components is realized using the theory of "soft computations" using the Mamdani fuzzy inference algorithm.

Optics education for machine operators in the semiconductor industry: moving beyond button pushing

NASA Astrophysics Data System (ADS)

Karakekes, Meg; Currier, Deborah

1995-10-01

In the competitive semiconductor manufacturing industry, employees who operate equipment are able to make greater contributions if they understand how the equipment works. By understanding the 'why' behind the 'what', the equipment operators can better partner with other technical staff to produce quality integrated circuits efficiently and effectively. This additional knowledge also opens equipment operators to job enrichment and enlargement opportunities. Advanced Micro Devices (AMD) is in the process of upgrading the skills of its equipment operators. This paper is an overview of a pilot program that employs optics education to upgrade stepper operators' skills. The paper starts with stepper tasks that require optics knowledge, examines teaching methods, reports both end-of-course and three months post-training knowledge retention, and summarizes how the training has impacted the production floor.

Key Tasks of Science in Improving Effectiveness of Hard Coal Production in Poland

NASA Astrophysics Data System (ADS)

Dubiński, Józef; Prusek, Stanisław; Turek, Marian

2017-09-01

The article presents an array of specific issues regarding the employed technology and operational efficiency of mining activities, which could and should become the subject of conducted scientific research. Given the circumstances of strong market competition and increasing requirements concerning environmental conditions, both in terms of conducted mining activities and produced coal quality parameters, it is imperative to develop and implement innovative solutions regarding the employed production technology, the safety of work conducted under the conditions of increasing natural hazards, as well as the mining enterprise management systems that enable its effective functioning. The article content pertains to the last group of issues in the most detailed way, particularly in terms of the possibility for rational conducted operation cost reduction.

Advanced Transportation System Studies. Technical Area 3: Alternate Propulsion Subsystem Concepts. Volume 1; Executive Summary

NASA Technical Reports Server (NTRS)

Levack, Daniel J. H.

2000-01-01

The Alternate Propulsion Subsystem Concepts contract had seven tasks defined that are reported under this contract deliverable. The tasks were: FAA Restart Study, J-2S Restart Study, Propulsion Database Development. SSME Upper Stage Use. CERs for Liquid Propellant Rocket Engines. Advanced Low Cost Engines, and Tripropellant Comparison Study. The two restart studies, F-1A and J-2S, generated program plans for restarting production of each engine. Special emphasis was placed on determining changes to individual parts due to obsolete materials, changes in OSHA and environmental concerns, new processes available, and any configuration changes to the engines. The Propulsion Database Development task developed a database structure and format which is easy to use and modify while also being comprehensive in the level of detail available. The database structure included extensive engine information and allows for parametric data generation for conceptual engine concepts. The SSME Upper Stage Use task examined the changes needed or desirable to use the SSME as an upper stage engine both in a second stage and in a translunar injection stage. The CERs for Liquid Engines task developed qualitative parametric cost estimating relationships at the engine and major subassembly level for estimating development and production costs of chemical propulsion liquid rocket engines. The Advanced Low Cost Engines task examined propulsion systems for SSTO applications including engine concept definition, mission analysis. trade studies. operating point selection, turbomachinery alternatives, life cycle cost, weight definition. and point design conceptual drawings and component design. The task concentrated on bipropellant engines, but also examined tripropellant engines. The Tripropellant Comparison Study task provided an unambiguous comparison among various tripropellant implementation approaches and cycle choices, and then compared them to similarly designed bipropellant engines in the SSTO mission This volume overviews each of the tasks giving its objectives, main results. and conclusions. More detailed Final Task Reports are available on each individual task.

An Integrated Decision-Making Model for Categorizing Weather Products and Decision Aids

NASA Technical Reports Server (NTRS)

Elgin, Peter D.; Thomas, Rickey P.

2004-01-01

The National Airspace System s capacity will experience considerable growth in the next few decades. Weather adversely affects safe air travel. The FAA and NASA are working to develop new technologies that display weather information to support situation awareness and optimize pilot decision-making in avoiding hazardous weather. Understanding situation awareness and naturalistic decision-making is an important step in achieving this goal. Information representation and situation time stress greatly influence attentional resource allocation and working memory capacity, potentially obstructing accurate situation awareness assessments. Three naturalistic decision-making theories were integrated to provide an understanding of the levels of decision making incorporated in three operational situations and two conditions. The task characteristics associated with each phase of flight govern the level of situation awareness attained and the decision making processes utilized. Weather product s attributes and situation task characteristics combine to classify weather products according to the decision-making processes best supported. In addition, a graphical interface is described that affords intuitive selection of the appropriate weather product relative to the pilot s current flight situation.

Heat pump concepts for nZEB Technology developments, design tools and testing of heat pump systems for nZEB in the USA: Country report IEA HPT Annex 40 Task 2, Task 3 and Task 4 of the USA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baxter, Van D.; Payne, W. Vance; Ling, Jiazhen

The IEA HPT Annex 40 "Heat pump concepts for Nearly Zero Energy Buildings" deals with the application of heat pumps as a core component of the HVAC system for Nearly or Net Zero energy buildings (nZEB). This report covers Task 2 on the system comparison and optimisation and Task 3 dedicated to the development of adapted technologies for nZEB and field monitoring results of heat pump systems in nZEB. In the US team three institutions are involved and have worked on the following projects: The Oak Ridge National Laboratory (ORNL) will summarize development activities through the field demonstration stage formore » several integrated heat pump (IHP) systems electric ground-source (GS-IHP) and air-source (AS-IHP) versions and an engine driven AS-IHP version. The first commercial GS-IHP product was just introduced to the market in December 2012. This work is a contribution to Task 3 of the Annex. The University of Maryland will contribute a software development project to Task 2 of the Annex. The software ThermCom evaluates occupied space thermal comfort conditions accounting for all radiative and convective heat transfer effects as well as local air properties. The National Institute of Standards and Technology (NIST) is working on a field study effort on the NIST Net Zero Energy Residential Test Facility (NZERTF). This residential building was constructed on the NIST campus and officially opened in summer 2013. During the first year, between July 2013 and June 2014, baseline performance of the NZERTF was monitored under a simulated occupancy protocol. The house was equipped with an air-to-air heat pump which included a dedicated dehumidification operating mode. Outdoor conditions, internal loads and modes of heat pump operation were monitored. Field study results with respect to heat pump operation will be reported and recommendations on heat pump optimization for a net zero energy building will be provided. This work is a contribution to Task 3 of the Annex.« less

Productivity increase through implementation of CAD/CAE workstation

NASA Technical Reports Server (NTRS)

Bromley, L. K.

1985-01-01

The tracking and communication division computer aided design/computer aided engineering system is now operational. The system is utilized in an effort to automate certain tasks that were previously performed manually. These tasks include detailed test configuration diagrams of systems under certification test in the ESTL, floorplan layouts of future planned laboratory reconfigurations, and other graphical documentation of division activities. The significant time savings achieved with this CAD/CAE system are examined: (1) input of drawings and diagrams; (2) editing of initial drawings; (3) accessibility of the data; and (4) added versatility. It is shown that the Applicon CAD/CAE system, with its ease of input and editing, the accessibility of data, and its added versatility, has made more efficient many of the necessary but often time-consuming tasks associated with engineering design and testing.

Operationally efficient propulsion system study (OEPSS) data book. Volume 6; Space Transfer Propulsion Operational Efficiency Study Task of OEPSS

NASA Technical Reports Server (NTRS)

Harmon, Timothy J.

1992-01-01

This document is the final report for the Space Transfer Propulsion Operational Efficiency Study Task of the Operationally Efficient Propulsion System Study (OEPSS) conducted by the Rocketdyne Division of Rockwell International. This Study task studied, evaluated and identified design concepts and technologies which minimized launch and in-space operations and optimized in-space vehicle propulsion system operability.

Automatic Adviser on Mobile Objects Status Identification and Classification

NASA Astrophysics Data System (ADS)

Shabelnikov, A. N.; Liabakh, N. N.; Gibner, Ya M.; Saryan, A. S.

2018-05-01

A mobile object status identification task is defined within the image discrimination theory. It is proposed to classify objects into three classes: object operation status; its maintenance is required and object should be removed from the production process. Two methods were developed to construct the separating boundaries between the designated classes: a) using statistical information on the research objects executed movement, b) basing on regulatory documents and expert commentary. Automatic Adviser operation simulation and the operation results analysis complex were synthesized. Research results are commented using a specific example of cuts rolling from the hump yard. The work was supported by Russian Fundamental Research Fund, project No. 17-20-01040.

Effects of cues in a binary categorization task on dual-task performance, mental workload, and effort.

PubMed

Botzer, Assaf; Meyer, Joachim; Parmet, Yisrael

2016-09-01

Binary cues help operators perform binary categorization tasks, such as monitoring for system failures. They may also allow them to attend to other tasks they concurrently perform. If the time saved by using cues is allocated to other concurrent tasks, users' overall effort may remain unchanged. In 2 experiments, participants performed a simulated quality control task, together with a tracking task. In half the experimental blocks cues were available, and participants could use them in their decisions about the quality of products (intact or faulty). In Experiment 1, the difficulty of tracking was constant, while in Experiment 2, tracking difficulty differed in the 2 halves of the experiment. In both experiments, participants reported on the NASA Task Load Index that cues improved their performance and reduced their frustration. Consequently, their overall score on mental workload (MWL) was lower with cues. They also reported, however, that cues did not reduce their effort. We conclude that cues and other forms of automation may support task performance and reduce overall MWL, but this will not necessarily mean that users will work less hard. Thus, effort and overall MWL should be evaluated separately, if one wants to obtain a full picture of the effects of automation. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

A Low-cost, High-yield Process for the Direct Productin of High Energy Density Liquid Fuel from Biomass

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agrawal, Rakesh; Delgass, W. N.; Ribeiro, F.

2013-08-31

The primary objective and outcome of this project was the development and validation of a novel, low-cost, high-pressure fast-hydropyrolysis/hydrodeoxygenation (HDO) process (H 2Bioil) using supplementary hydrogen (H 2) to produce liquid hydrocarbons from biomass. The research efforts under the various tasks of the project have culminated in the first experimental demonstration of the H 2Bioil process, producing 100% deoxygenated >C4+ hydrocarbons containing 36-40% of the carbon in the feed of pyrolysis products from biomass. The demonstrated H{sub 2}Bioil process technology (i.e. reactor, catalyst, and downstream product recovery) is scalable to a commercial level and is estimated to be economically competitivemore » for the cases when supplementary H 2 is sourced from coal, natural gas, or nuclear. Additionally, energy systems modeling has revealed several process integration options based on the H 2Bioilprocess for energy and carbon efficient liquid fuel production. All project tasks and milestones were completed or exceeded. Novel, commercially-scalable, high-pressure reactors for both fast-hydropyrolysis and hydrodeoxygenation were constructed, completing Task A. These reactors were capable of operation under a wide-range of conditions; enabling process studies that lead to identification of optimum process conditions. Model compounds representing biomass pyrolysis products were studied, completing Task B. These studies were critical in identifying and developing HDO catalysts to target specific oxygen functional groups. These process and model compound catalyst studies enabled identification of catalysts that achieved 100% deoxygenation of the real biomass feedstock, sorghum, to form hydrocarbons in high yields as part of Task C. The work completed during this grant has identified and validated the novel and commercially scalable H 2Bioil process for production of hydrocarbon fuels from biomass. Studies on model compounds as well as real biomass feedstocks were utilized to identify optimized process conditions and selective HDO catalyst for high yield production of hydrocarbons from biomass. In addition to these experimental efforts, in Tasks D and E, we have developed a mathematical optimization framework to identify carbon and energy efficient biomass-to-liquid fuel process designs that integrate the use of different primary energy sources along with biomass (e.g. solar, coal or natural gas) for liquid fuel production. Using this tool, we have identified augmented biomass-to-liquid fuel configurations based on the fast-hydropyrolysis/HDO pathway, which was experimentally studied in this project. The computational approach used for screening alternative process configurations represents a unique contribution to the field of biomass processing for liquid fuel production.« less

PRAIS: Distributed, real-time knowledge-based systems made easy

NASA Technical Reports Server (NTRS)

Goldstein, David G.

1990-01-01

This paper discusses an architecture for real-time, distributed (parallel) knowledge-based systems called the Parallel Real-time Artificial Intelligence System (PRAIS). PRAIS strives for transparently parallelizing production (rule-based) systems, even when under real-time constraints. PRAIS accomplishes these goals by incorporating a dynamic task scheduler, operating system extensions for fact handling, and message-passing among multiple copies of CLIPS executing on a virtual blackboard. This distributed knowledge-based system tool uses the portability of CLIPS and common message-passing protocols to operate over a heterogeneous network of processors.

Process development for automated solar cell and module production. Task 4: Automated array assembly

NASA Technical Reports Server (NTRS)

Hagerty, J. J.

1981-01-01

The Unimate robot was programmed for the final 35 cell pattern to be used in the fabrication of the deliverable modules. Mechanical construction of the Automated Lamination Station and Final Assembly Station were completed on schedule. All final wiring and interconnect cables were also completed and the first operational testing began. The final controlling program was written. A local fabricator was contracted to produce the glass reinforced concrete panels to be used for testing and deliverables. A video tape showing all three stations in operation was produced.

Peculiarities of solving the problems of modern logistics in high-rise construction and industrial production

NASA Astrophysics Data System (ADS)

Rubtsov, Anatoliy E.; Ushakova, Elena V.; Chirkova, Tamara V.

2018-03-01

Basing on the analysis of the enterprise (construction organization) structure and infrastructure of the entire logistics system in which this enterprise (construction organization) operates, this article proposes an approach to solve the problems of structural optimization and a set of calculation tasks, based on customer orders as well as on the required levels of insurance stocks, transit stocks and other types of stocks in the distribution network, modes of operation of the in-company transport and storage complex and a number of other factors.

Financial advantages. Preventative measures ensure the health of your accounts receivable.

PubMed

Duda, Michelle

2009-11-01

Running a dental practice is no small task; from staying on the leading edge of new medical developments and products, to monitoring ever-changing dental insurance plans, to simply overseeing the fundamental day-to-day operations. But there is one area of your practice that can be streamlined to significantly improve your cash flow, minimize delinquencies and optimize fiscal operations. Your accounts receivable and collections can be economically and efficiently managed by a savvy combination of internal efforts and the partnership of a third party resource.

Low cost solar array project silicon materials task. Development of a process for high capacity arc heater production of silicon for solar arrays

NASA Technical Reports Server (NTRS)

Fey, M. G.

1981-01-01

The experimental verification system for the production of silicon via the arc heater-sodium reduction of SiCl4 was designed, fabricated, installed, and operated. Each of the attendant subsystems was checked out and operated to insure performance requirements. These subsystems included: the arc heaters/reactor, cooling water system, gas system, power system, Control & Instrumentation system, Na injection system, SiCl4 injection system, effluent disposal system and gas burnoff system. Prior to introducing the reactants (Na and SiCl4) to the arc heater/reactor, a series of gas only-power tests was conducted to establish the operating parameters of the three arc heaters of the system. Following the successful completion of the gas only-power tests and the readiness tests of the sodium and SiCl4 injection systems, a shakedown test of the complete experimental verification system was conducted.

Job Language Performance Requirements for MOS 72E, Telecommunications Center Operator.

DTIC Science & Technology

1982-10-01

Process Outgoing *"asp to be raaomitt4d in Finished card Format 113-572-MW0 Process Outgoing NMessa to be Iranmi ttad to %"ptic Tap& Format 113-5724006...LANGUAGE naOvAiW (Satire Oe) The product of the entire data gathering and organization is the ILVR 0. These are relevant to all ,- coton and duty tasks

Nuclear physics research operation. Monthly report, November 1958

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faulkner, J.E.

1958-12-10

This report is a summary of projects worked on in support of the production reactors at Hanford. The projects include criticality studies, from tasks associated with fuel element reprocessing to shipments of slightly enriched uranium. They include studies of neutron cross sections for different reactions and neutron flux measurements in different reactor locations, as well as design studies for future reactor projects.

Distribution and interaction of white-tailed deer and cattle in a semi-arid grazing system

Treesearch

Susan M. Cooper; Humberto L. Perotto-Baldivieso; M. Keith Owens; Michael G. Meek; Manuel Figueroa-Pagan

2008-01-01

In order to optimize production, range managers need to understand and manage the spatial distribution of free-ranging herbivores, although this task becomes increasingly difficult as ranching operations diversify to include management of wildlife for recreational hunting. White-tailed deer are sympatric with cattle throughout much of their range and are a valuable...

Assessment of Human Factors

NASA Technical Reports Server (NTRS)

Mount, Frances; Foley, Tico

1999-01-01

Human Factors Engineering, often referred to as Ergonomics, is a science that applies a detailed understanding of human characteristics, capabilities, and limitations to the design, evaluation, and operation of environments, tools, and systems for work and daily living. Human Factors is the investigation, design, and evaluation of equipment, techniques, procedures, facilities, and human interfaces, and encompasses all aspects of human activity from manual labor to mental processing and leisure time enjoyments. In spaceflight applications, human factors engineering seeks to: (1) ensure that a task can be accomplished, (2) maintain productivity during spaceflight, and (3) ensure the habitability of the pressurized living areas. DSO 904 served as a vehicle for the verification and elucidation of human factors principles and tools in the microgravity environment. Over six flights, twelve topics were investigated. This study documented the strengths and limitations of human operators in a complex, multifaceted, and unique environment. By focusing on the man-machine interface in space flight activities, it was determined which designs allow astronauts to be optimally productive during valuable and costly space flights. Among the most promising areas of inquiry were procedures, tools, habitat, environmental conditions, tasking, work load, flexibility, and individual control over work.

Design and field test of collaborative tools in the service of an innovative organization

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Beler, N.; Parfouru, S.

2012-07-01

This paper presents the design process of collaborative tools, based on ICT, aiming at supporting the tasks of the team that manages an outage of an energy production plant for maintenance activities. The design process follows an iterative and multidisciplinary approach, based on a collective tasks modeling of the outage management team in the light of Socio Organizational and Human (SOH) field studies, and on the state of the art of ICT. Field test of the collaborative tools designed plays a great place in this approach, allowing taking into account the operational world but involves also some risks which mustmore » be managed. To implement tools on all the production plants, we build an 'operational concept' with a level of description which authorizes the evolution of tools and allows some local adaptations. The field tests provide lessons on the ICT topics. For examples: the status of the remote access tools, the potential of use of a given information input by an actor for several individual and collective purposes, the actors perception of the tools meaning, and the requirements for supporting the implementation of change. (authors)« less

Automated Formosat Image Processing System for Rapid Response to International Disasters

NASA Astrophysics Data System (ADS)

Cheng, M. C.; Chou, S. C.; Chen, Y. C.; Chen, B.; Liu, C.; Yu, S. J.

2016-06-01

FORMOSAT-2, Taiwan's first remote sensing satellite, was successfully launched in May of 2004 into the Sun-synchronous orbit at 891 kilometers of altitude. With the daily revisit feature, the 2-m panchromatic, 8-m multi-spectral resolution images captured have been used for researches and operations in various societal benefit areas. This paper details the orchestration of various tasks conducted in different institutions in Taiwan in the efforts responding to international disasters. The institutes involved including its space agency-National Space Organization (NSPO), Center for Satellite Remote Sensing Research of National Central University, GIS Center of Feng-Chia University, and the National Center for High-performance Computing. Since each institution has its own mandate, the coordinated tasks ranged from receiving emergency observation requests, scheduling and tasking of satellite operation, downlink to ground stations, images processing including data injection, ortho-rectification, to delivery of image products. With the lessons learned from working with international partners, the FORMOSAT Image Processing System has been extensively automated and streamlined with a goal to shorten the time between request and delivery in an efficient manner. The integrated team has developed an Application Interface to its system platform that provides functions of search in archive catalogue, request of data services, mission planning, inquiry of services status, and image download. This automated system enables timely image acquisition and substantially increases the value of data product. Example outcome of these efforts in recent response to support Sentinel Asia in Nepal Earthquake is demonstrated herein.

Flying Cassini with Virtual Operations Teams

NASA Technical Reports Server (NTRS)

Dodd, Suzanne; Gustavson, Robert

1998-01-01

The Cassini Program's challenge is to fly a large, complex mission with a reduced operations budget. A consequence of the reduced budget is elimination of the large, centrally located group traditionally used for uplink operations. Instead, responsibility for completing parts of the uplink function is distributed throughout the Program. A critical strategy employed to handle this challenge is the use of Virtual Uplink Operations Teams. A Virtual Team is comprised of a group of people with the necessary mix of engineering and science expertise who come together for the purpose of building a specific uplink product. These people are drawn from throughout the Cassini Program and participate across a large geographical area (from Germany to the West coast of the USA), covering ten time zones. The participants will often split their time between participating in the Virtual Team and accomplishing their core responsibilities, requiring significant planning and time management. When the particular uplink product task is complete, the Virtual Team disbands and the members turn back to their home organization element for future work assignments. This time-sharing of employees is used on Cassini to build mission planning products, via the Mission Planning Virtual Team, and sequencing products and monitoring of the sequence execution, via the Sequence Virtual Team. This challenging, multitasking approach allows efficient use of personnel in a resource constrained environment.

CO-FIRING COAL: FEEDLOT AND LITTER BIOMASS FUELS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Unknown

2002-07-01

Proposed activities for quarter 8 (3/15/2001--6/14/2002), Boiler Burner Simulation and Experiments: (1) Continue the parametric study of cofiring of pulverized coal and LB in the boiler burner, and determining the combustor performance and emissions of NO, CO, CO{sub 2}, PO{sub 2} and P{sub 4}O{sub 10}, etc. The air-fuel ratio, swirl number of the secondary air stream and moisture effects will also be investigated (Task 4). Gasification: (Task 3) (2) Measuring the temperature profile for chicken litter biomass under different operating conditions. (3) Product gas species for different operating conditions for different fuels. (4) Determining the bed ash composition for differentmore » fuels. (5) Determining the gasification efficiency for different operating conditions. Activities Achieved during quarter 8 (3/15/2001--6/14/2002), Boiler Burner Simulation and Experiments: (1) The evaporation and phosphorus combustion models have been incorporated into the PCGC-2 code. Mr. Wei has successfully defended his Ph.D. proposal on Coal: LB modeling studies (Task 4, Appendix C). (2) Reburn experiments with both low and high phosphorus feedlot biomass has been performed (Task 2, Appendix A). (3) Parametric studies on the effect of air-fuel ratio, swirl number of the secondary air stream and moisture effects have been investigated (Task 2, Appendix A). (4) Three abstracts have been submitted to the American Society of Agricultural Engineers Annual International meeting at Chicago in July 2002. Three part paper dealing with fuel properties, cofiring, large scale testing are still under review in the Journal of Fuel. Gasification: (Task 3, Appendix B) (5) Items No. 2, and 3 are 95% complete, with four more experiments yet to be performed with coal and chicken litter biomass blends. (6) Item No. 4, and 5 shall be performed after completion of all the experiments.« less

Centralized operations and maintenance planning at the Atacama Large Millimeter/submillimeter Array (ALMA)

NASA Astrophysics Data System (ADS)

Lopez, Bernhard; Whyborn, Nicholas D.; Guniat, Serge; Hernandez, Octavio; Gairing, Stefan

2016-07-01

The Atacama Large Millimeter/submillimeter Array (ALMA) is a joint project between astronomical organizations in Europe, North America, and East Asia, in collaboration with the Republic of Chile. ALMA consists of 54 twelve-meter antennas and 12 seven-meter antennas operating as an aperture synthesis array in the (sub)millimeter wavelength range. Since the inauguration of the observatory back in March 2013 there has been a continuous effort to establish solid operations processes for effective and efficient management of technical and administrative tasks on site. Here a key aspect had been the centralized maintenance and operations planning: input is collected from science stakeholders, the computerized maintenance management system (CMMS) and from the technical teams spread around the world, then this information is analyzed and consolidated based on the established maintenance strategy, the observatory long-term plan and the short-term priorities definitions. This paper presents the high-level process that has been developed for the planning and scheduling of planned- and unplanned maintenance tasks, and for site operations like the telescope array reconfiguration campaigns. We focus on the centralized planning approach by presenting its genesis, its current implementation for the observatory operations including related planning products, and we explore the necessary next steps in order to fully achieve a comprehensive centralized planning approach for ALMA in steady-state operations.

Agricultural Production: Task Analysis for Livestock Production. Competency-Based Education.

ERIC Educational Resources Information Center

Henrico County Public Schools, Glen Allen, VA. Virginia Vocational Curriculum Center.

This task analysis guide is intended to help teachers and administrators develop instructional materials and implement competency-based education in the agricultural production program. Section 1 contains a validated task inventory for the livestock production portion of agricultural production IV and V. Tasks are divided into six duty areas:…

Effects of Selected Task Performance Criteria at Initiating Adaptive Task Real locations

NASA Technical Reports Server (NTRS)

Montgomery, Demaris A.

2001-01-01

In the current report various performance assessment methods used to initiate mode transfers between manual control and automation for adaptive task reallocation were tested. Participants monitored two secondary tasks for critical events while actively controlling a process in a fictional system. One of the secondary monitoring tasks could be automated whenever operators' performance was below acceptable levels. Automation of the secondary task and transfer of the secondary task back to manual control were either human- or machine-initiated. Human-initiated transfers were based on the operator's assessment of the current task demands while machine-initiated transfers were based on the operators' performance. Different performance assessment methods were tested in two separate experiments.

Verification and Implementation of Operations Safety Controls for Flight Missions

NASA Technical Reports Server (NTRS)

Jones, Cheryl L.; Smalls, James R.; Carrier, Alicia S.

2010-01-01

Approximately eleven years ago, the International Space Station launched the first module from Russia, the Functional Cargo Block (FGB). Safety and Mission Assurance (S&MA) Operations (Ops) Engineers played an integral part in that endeavor by executing strict flight product verification as well as continued staffing of S&MA's console in the Mission Evaluation Room (MER) for that flight mission. How were these engineers able to conduct such a complicated task? They conducted it based on product verification that consisted of ensuring that safety requirements were adequately contained in all flight products that affected crew safety. S&MA Ops engineers apply both systems engineering and project management principles in order to gain a appropriate level of technical knowledge necessary to perform thorough reviews which cover the subsystem(s) affected. They also ensured that mission priorities were carried out with a great detail and success.

Interindividual variability in the hemispheric organization for speech.

PubMed

Tzourio-Mazoyer, N; Josse, G; Crivello, F; Mazoyer, B

2004-01-01

A PET activation study was designed to investigate hemispheric specialization during speech comprehension and production in right- and left-handed subjects. Normalized regional cerebral blood flow (NrCBF) was repeatedly monitored while subjects either listened to factual stories (Story) or covertly generated verbs semantically related to heard nouns (Gener), using silent resting (Rest) as a common control condition. NrCBF variations in each task, as compared to Rest, as well as functional asymmetry indices (FAI = right minus left NrCBF variations), were computed in anatomical regions of interest (AROIs) defined on the single-subject MNI template. FAIs were predominantly leftward in all regions during both tasks, although larger FAIs were observed during Gener. Subjects were declared "typical" for language hemispheric specialization based on the presence of significant leftward asymmetries (FAI < 0) in the pars triangularis and opercularis of the inferior frontal gyrus during Gener, and in the middle and inferior temporal AROIs during Story. Six subjects (including five LH) showed an atypical language representation. Among them, one presented a right hemisphere specialization during both tasks, another a shift in hemispheric specialization from production to comprehension (left during Gener, right during Story). The group of 14 typical subjects showed significant positive correlation between homologous left and right AROIs NrCBF variations in temporal areas during Story, and in temporal and inferior frontal areas during Gener, almost all regions presenting a leftward FAI. Such correlations were also present in deactivated areas with strong leftward asymmetry (supramarginalis gyrus, inferior parietal region). These results suggest that entry into a language task translates into a hemispheric reconfiguration of lateral cortical areas with global NrCBF increase in the dominant hemisphere and decrease in the minor hemisphere. This can be considered as the setting up of a "language mode", under the control of a mechanism that operates at a perisylvian level. On top of this global organization, regional variations carry on the performance of the cognitive operations specific to the language task to be performed. Hemispheric relationships could be different in atypical subjects, with either between task hemispheric regulation differences or differences in regional specialization.

The heuristic basis of remembering and classification: fluency, generation, and resemblance.

PubMed

Whittlesea, B W; Leboe, J P

2000-03-01

People use 3 heuristics (fluency, generation, and resemblance) in remembering a prior experience of a stimulus. The authors demonstrate that people use the same 3 heuristics in classifying a stimulus as a member of a category and interpret this as support for the idea that people have a unitary memory system that operates by the same fundamental principles in both remembering and nonremembering tasks. The authors argue that the fundamental functions of memory are the production of specific mental events, under the control of the stimulus, task, and context, and the evaluation of the coherence of those events, which controls the subjective experience accompanying performance.

Object-based task-level control: A hierarchical control architecture for remote operation of space robots

NASA Technical Reports Server (NTRS)

Stevens, H. D.; Miles, E. S.; Rock, S. J.; Cannon, R. H.

1994-01-01

Expanding man's presence in space requires capable, dexterous robots capable of being controlled from the Earth. Traditional 'hand-in-glove' control paradigms require the human operator to directly control virtually every aspect of the robot's operation. While the human provides excellent judgment and perception, human interaction is limited by low bandwidth, delayed communications. These delays make 'hand-in-glove' operation from Earth impractical. In order to alleviate many of the problems inherent to remote operation, Stanford University's Aerospace Robotics Laboratory (ARL) has developed the Object-Based Task-Level Control architecture. Object-Based Task-Level Control (OBTLC) removes the burden of teleoperation from the human operator and enables execution of tasks not possible with current techniques. OBTLC is a hierarchical approach to control where the human operator is able to specify high-level, object-related tasks through an intuitive graphical user interface. Infrequent task-level command replace constant joystick operations, eliminating communications bandwidth and time delay problems. The details of robot control and task execution are handled entirely by the robot and computer control system. The ARL has implemented the OBTLC architecture on a set of Free-Flying Space Robots. The capability of the OBTLC architecture has been demonstrated by controlling the ARL Free-Flying Space Robots from NASA Ames Research Center.

STAR Algorithm Integration Team - Facilitating operational algorithm development

NASA Astrophysics Data System (ADS)

Mikles, V. J.

2015-12-01

The NOAA/NESDIS Center for Satellite Research and Applications (STAR) provides technical support of the Joint Polar Satellite System (JPSS) algorithm development and integration tasks. Utilizing data from the S-NPP satellite, JPSS generates over thirty Environmental Data Records (EDRs) and Intermediate Products (IPs) spanning atmospheric, ocean, cryosphere, and land weather disciplines. The Algorithm Integration Team (AIT) brings technical expertise and support to product algorithms, specifically in testing and validating science algorithms in a pre-operational environment. The AIT verifies that new and updated algorithms function in the development environment, enforces established software development standards, and ensures that delivered packages are functional and complete. AIT facilitates the development of new JPSS-1 algorithms by implementing a review approach based on the Enterprise Product Lifecycle (EPL) process. Building on relationships established during the S-NPP algorithm development process and coordinating directly with science algorithm developers, the AIT has implemented structured reviews with self-contained document suites. The process has supported algorithm improvements for products such as ozone, active fire, vegetation index, and temperature and moisture profiles.

Cognitive Task Analysis of the HALIFAX-Class Operations Room Officer

DTIC Science & Technology

1999-03-10

Image Cover Sheet CLASSIFICATION SYSTEM NUMBER 510918 UNCLASSIFIED llllllllllllllllllllllllllllllllllllllll TITLE COGNITIVE TASK ANALYSIS OF THE...DATES COVERED 00-00-1999 to 00-00-1999 4. TITLE AND SUBTITLE Cognitive Task Analysis of the HALIFAX-Class Operations Room Officer 5a. CONTRACT...Ontario . ~ -- . ’ c ... - Incorporated Cognitive Task Analysis of the HALIFAX-Class Operations Room Officer: PWGSC Contract No. W7711-7-7404/001/SV

Determinants of wheat antigen and fungal alpha-amylase exposure in bakeries.

PubMed

Burstyn, I; Teschke, K; Bartlett, K; Kennedy, S M

1998-05-01

The study's objectives were to measure flour antigen exposure in bakeries and define the determinants of exposure. Ninety-six bakery workers, employed in seven different bakeries, participated in the study. Two side-by-side full-shift inhalable dust samples were obtained from each study participant on a single occasion. The flour antigen exposure was measured as wheat antigen and fungal alpha-amylase content of the water-soluble fraction of inhalable dust, assayed via enzyme-linked immunosorbent assays. During the entire sampling period bakers were observed and information on 14 different tasks was recorded at 15-minute intervals. Other production characteristics were also recorded for each sampling day and used in statistical modeling to identify significant predictors of exposure. The mean alpha-amylase antigen exposure was 22.0 ng/m3 (ranging from below the limit of detection of 0.1 ng/m3 to 307.1 ng/m3) and the mean wheat antigen exposure was 109 micrograms/m3 (ranging from below the limit of detection of 1 microgram/m3 to 1018 micrograms/m3). Regression models that explained 74% of variability in wheat antigen and alpha-amylase antigen exposures were constructed. The models indicated that tasks such as weighing, pouring, and operating dough-brakers increased flour antigen exposure, while packing and decorating resulted in lower exposures. Croissant, puff-pastry, and bread/bun production lines were associated with increased exposure, while cake production and substitution of dusting with the use of divider oil were associated with decreased exposure. Exposure levels can be reduced by the automation of forming tasks, alteration of tasks requiring pouring of flour, and changes to the types of products manufactured.

Task-dependent and task-independent neurovascular responses to syntactic processing⋆

PubMed Central

Caplan, David; Chen, Evan; Waters, Gloria

2008-01-01

The neural basis for syntactic processing was studied using event-related fMRI to determine the locations of BOLD signal increases in the contrast of syntactically complex sentences with center-embedded, object-extracted relative clauses and syntactically simple sentences with right-branching, subject-extracted relative clauses in a group of 15 participants in three tasks. In a sentence verification task, participants saw a target sentence in one of these two syntactic forms, followed by a probe in a simple active form, and determined whether the probe expressed a proposition in the target. In a plausibility judgment task, participants determined whether a sentence in one of these two syntactic forms was plausible or implausible. Finally, in a non-word detection task, participants determined whether a sentence in one of these two syntactic forms contained only real words or a non-word. BOLD signal associated with the syntactic contrast increased in the left posterior inferior frontal gyrus in non-word detection and in a widespread set of areas in the other two tasks. We conclude that the BOLD activity in the left posterior inferior frontal gyrus reflects syntactic processing independent of concurrent cognitive operations and the more widespread areas of activation reflect the use of strategies and the use of the products of syntactic processing to accomplish tasks. PMID:18387556

The TMIS life-cycle process document, revision A

NASA Technical Reports Server (NTRS)

1991-01-01

The Technical and Management Information System (TMIS) Life-Cycle Process Document describes the processes that shall be followed in the definition, design, development, test, deployment, and operation of all TMIS products and data base applications. This document is a roll out of TMIS Standards Document (SSP 30546). The purpose of this document is to define the life cycle methodology that the developers of all products and data base applications and any subsequent modifications shall follow. Included in this methodology are descriptions of the tasks, deliverables, reviews, and approvals that are required before a product or data base application is accepted in the TMIS environment.

Effects of Nicotine on Olfactogustatory Incentives: Preference, Palatability, and Operant Choice Tests

PubMed Central

2013-01-01

Introduction: The use of additives in tobacco may capitalize on the incentive motivational properties of tastes and scents such as mint (menthol), vanilla, and strawberry. These incentives are intended to increase tobacco experimentation, but their salience may also be enhanced by the incentive amplifying effects of nicotine (NIC). The goal of the present studies was to investigate the potential interaction between the incentive amplifying effects of NIC and gustatory incentives. Methods: One of two discriminable tastes (grape or cherry Kool-Aid®; 0.05% wt/vol; unsweetened) was paired with sucrose (20% wt/vol; conditioned stimulus [CS+]) in deionized water, whereas the other taste (CS−) was presented in deionized water. Experiment 1 investigated the effects of NIC pretreatment on preference for the CS+ versus CS− in 2-bottle choice tests. Experiment 2 investigated the effects of NIC on palatability of the CS+ and CS− using orofacial taste reactions. Experiment 3 investigated the effects of NIC on reinforcement by the CS+ and CS− using a concurrent choice operant task. Results: NIC pretreatment robustly increased operant responding for the CS+ but did not alter responding for the CS− in the operant choice task (Experiment 3). However, NIC pretreatment did not alter intake or palatability of the CS+ or CS− (Experiments 1 and 2). Conclusions: NIC increases the reinforcing effects of gustatory incentive stimuli, even though these stimuli were not paired with NIC administration. The findings suggest that adding taste incentives to tobacco products may increase the attractiveness of these products to consumers and the probability of repeated use. PMID:23430737

The Jet Propulsion Laboratory shared control architecture and implementation

NASA Technical Reports Server (NTRS)

Backes, Paul G.; Hayati, Samad

1990-01-01

A hardware and software environment for shared control of telerobot task execution has been implemented. Modes of task execution range from fully teleoperated to fully autonomous as well as shared where hand controller inputs from the human operator are mixed with autonomous system inputs in real time. The objective of the shared control environment is to aid the telerobot operator during task execution by merging real-time operator control from hand controllers with autonomous control to simplify task execution for the operator. The operator is the principal command source and can assign as much autonomy for a task as desired. The shared control hardware environment consists of two PUMA 560 robots, two 6-axis force reflecting hand controllers, Universal Motor Controllers for each of the robots and hand controllers, a SUN4 computer, and VME chassis containing 68020 processors and input/output boards. The operator interface for shared control, the User Macro Interface (UMI), is a menu driven interface to design a task and assign the levels of teleoperated and autonomous control. The operator also sets up the system monitor which checks safety limits during task execution. Cartesian-space degrees of freedom for teleoperated and/or autonomous control inputs are selected within UMI as well as the weightings for the teleoperation and autonmous inputs. These are then used during task execution to determine the mix of teleoperation and autonomous inputs. Some of the autonomous control primitives available to the user are Joint-Guarded-Move, Cartesian-Guarded-Move, Move-To-Touch, Pin-Insertion/Removal, Door/Crank-Turn, Bolt-Turn, and Slide. The operator can execute a task using pure teleoperation or mix control execution from the autonomous primitives with teleoperated inputs. Presently the shared control environment supports single arm task execution. Work is presently underway to provide the shared control environment for dual arm control. Teleoperation during shared control is only Cartesian space control and no force-reflection is provided. Force-reflecting teleoperation and joint space operator inputs are planned extensions to the environment.

Operator Workload: Comprehensive Review and Evaluation of Operator Workload Methodologies

DTIC Science & Technology

1989-06-01

chocking for system failures or emergency conditions. It seems fair to characterize the changes In operator functions as more mental or cognitive In nature ...that the operator, the system hardware, and the evMronment all interact in affecting performance and this Interaction can change the nature of the task...a) classifying the nature of the operator tasks and (b) classifying workload assessment techniques. Task taxonomies are useful because some workload

The effects of type of knowledge upon human problem solving in a process control task

NASA Technical Reports Server (NTRS)

Morris, N. M.; Rouse, W. B.

1985-01-01

The question of what the operator of a dynamic system needs to know was investigated in an experiment using PLANT, a simulation of a generic dynamic production process. Knowledge of PLANT was manipulated via different types of instruction, so that four different groups were created: (1) minimal instructions only; (2) minimal instructions and guidelines for operation (procedures); (3) minimal instructions and dynamic relationships (principles); and (4) minimal instructions, and procedures, and principles. Subjects controlled PLANT in a variety of situations which required maintaining production while also diagnosing familiar and unfamiliar failures. Despite the fact that these manipulations resulted in differences in subjects' Knowledge, as assessed via a written test at the end of the experiment, instructions had no effect upon achievement of the primary goal of production, or upon subjects' ability to diagnose unfamiliar failures. However, those groups receiving procedures controlled the system in a more stable manner. Possible reasons for the failure to find an effect of principles are presented, and the implications of these results for operator training and aiding are discussed.

Multifamily Building Operator Job/Task Analysis and Report: September 2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

Owens, C. M.

The development of job/task analyses (JTAs) is one of three components of the Guidelines for Home Energy Professionals project and will allow industry to develop training resources, quality assurance protocols, accredited training programs, and professional certifications. The Multifamily Building Operator JTA identifies and catalogs all of the tasks performed by multifamily building operators, as well as the knowledge, skills, and abilities (KSAs) needed to perform the identified tasks.

An Empirical Methodology for Engineering Human Systems Integration

DTIC Science & Technology

2009-12-01

scanning critical information and selectively skipping what is not important for the immediate task. This learned skill is called a proper “cross check...ability to recover from errors. Efficiency: the level of productivity that can be achieved once learning has occurred. 162 Learnability: the...use, to legacy systems. Knowing what design issues have plagued past operators can guide the generation of requirements to address the identified

Short Term Memory, Working Memory, and Syntactic Comprehension in Aphasia

PubMed Central

Caplan, David; Michaud, Jennifer; Hufford, Rebecca

2013-01-01

Sixty one people with aphasia were tested on ten tests of short term memory (STM) and for the ability to use syntactic structure to determine the meanings of eleven types of sentences in three tasks – object manipulation, picture matching and picture matching with self-paced listening. Multilevel models showed relationships between measures of the ability to retain and manipulate item and order information in STM and accuracy and RT, and a greater relationship between these STM measures and accuracy and RT for several more complex sentence types in individual tasks. There were no effects of measures of STM that reflect the use of phonological codes or rehearsal on comprehension. There was only one effect of STM measures on self-paced listening times. There were double dissociations between performance on STM and individual comprehension tasks, indicating that normal STM is not necessary to perform normally on these tasks. The results are most easily related to the view that STM plays a facilitatory role in supporting the use of the products of the comprehension process to accomplish operations related to tasks. PMID:23865692

A Validated Task Analysis of the Single Pilot Operations Concept

NASA Technical Reports Server (NTRS)

Wolter, Cynthia A.; Gore, Brian F.

2015-01-01

The current day flight deck operational environment consists of a two-person Captain/First Officer crew. A concept of operations (ConOps) to reduce the commercial cockpit to a single pilot from the current two pilot crew is termed Single Pilot Operations (SPO). This concept has been under study by researchers in the Flight Deck Display Research Laboratory (FDDRL) at the National Aeronautics and Space Administration's (NASA) Ames (Johnson, Comerford, Lachter, Battiste, Feary, and Mogford, 2012) and researchers from Langley Research Centers (Schutte et al., 2007). Transitioning from a two pilot crew to a single pilot crew will undoubtedly require changes in operational procedures, crew coordination, use of automation, and in how the roles and responsibilities of the flight deck and ATC are conceptualized in order to maintain the high levels of safety expected of the US National Airspace System. These modifications will affect the roles and the subsequent tasks that are required of the various operators in the NextGen environment. The current report outlines the process taken to identify and document the tasks required by the crew according to a number of operational scenarios studied by the FDDRL between the years 2012-2014. A baseline task decomposition has been refined to represent the tasks consistent with a new set of entities, tasks, roles, and responsibilities being explored by the FDDRL as the move is made towards SPO. Information from Subject Matter Expert interviews, participation in FDDRL experimental design meetings, and study observation was used to populate and refine task sets that were developed as part of the SPO task analyses. The task analysis is based upon the proposed ConOps for the third FDDRL SPO study. This experiment possessed nine different entities operating in six scenarios using a variety of SPO-related automation and procedural activities required to guide safe and efficient aircraft operations. The task analysis presents the roles and responsibilities in a manner that can facilitate testing future scenarios. Measures of task count and workload were defined and analyzed to assess the impact of transitioning to a SPO environment.

Evaluating space station applications of automation and robotics technologies from a human productivity point of view

NASA Technical Reports Server (NTRS)

Bard, J. F.

1986-01-01

The role that automation, robotics, and artificial intelligence will play in Space Station operations is now beginning to take shape. Although there is only limited data on the precise nature of the payoffs that these technologies are likely to afford there is a general consensus that, at a minimum, the following benefits will be realized: increased responsiveness to innovation, lower operating costs, and reduction of exposure to hazards. Nevertheless, the question arises as to how much automation can be justified with the technical and economic constraints of the program? The purpose of this paper is to present a methodology which can be used to evaluate and rank different approaches to automating the functions and tasks planned for the Space Station. Special attention is given to the impact of advanced automation on human productivity. The methodology employed is based on the Analytic Hierarchy Process. This permits the introduction of individual judgements to resolve the confict that normally arises when incomparable criteria underly the selection process. Because of the large number of factors involved in the model, the overall problem is decomposed into four subproblems individually focusing on human productivity, economics, design, and operations, respectively. The results from each are then combined to yield the final rankings. To demonstrate the methodology, an example is developed based on the selection of an on-orbit assembly system. Five alternatives for performing this task are identified, ranging from an astronaut working in space, to a dexterous manipulator with sensory feedback. Computational results are presented along with their implications. A final parametric analysis shows that the outcome is locally insensitive to all but complete reversals in preference.

Robustness analysis of non-ordinary Petri nets for flexible assembly/disassembly processes based on structural decomposition

NASA Astrophysics Data System (ADS)

Hsieh, Fu-Shiung

2011-03-01

Design of robust supervisory controllers for manufacturing systems with unreliable resources has received significant attention recently. Robustness analysis provides an alternative way to analyse a perturbed system to quickly respond to resource failures. Although we have analysed the robustness properties of several subclasses of ordinary Petri nets (PNs), analysis for non-ordinary PNs has not been done. Non-ordinary PNs have weighted arcs and have the advantage to compactly model operations requiring multiple parts or resources. In this article, we consider a class of flexible assembly/disassembly manufacturing systems and propose a non-ordinary flexible assembly/disassembly Petri net (NFADPN) model for this class of systems. As the class of flexible assembly/disassembly manufacturing systems can be regarded as the integration and interactions of a set of assembly/disassembly subprocesses, a bottom-up approach is adopted in this article to construct the NFADPN models. Due to the routing flexibility in NFADPN, there may exist different ways to accomplish the tasks. To characterise different ways to accomplish the tasks, we propose the concept of completely connected subprocesses. As long as there exists a set of completely connected subprocesses for certain type of products, the production of that type of products can still be maintained without requiring the whole NFADPN to be live. To take advantage of the alternative routes without enforcing liveness for the whole system, we generalise the concept of persistent production proposed to NFADPN. We propose a condition for persistent production based on the concept of completely connected subprocesses. We extend robustness analysis to NFADPN by exploiting its structure. We identify several patterns of resource failures and characterise the conditions to maintain operation in the presence of resource failures.

ISS Operations Cost Reductions Through Automation of Real-Time Planning Tasks

NASA Technical Reports Server (NTRS)

Hall, Timothy A.

2011-01-01

In 2008 the Johnson Space Center s Mission Operations Directorate (MOD) management team challenged their organization to find ways to reduce the costs of International Space station (ISS) console operations in the Mission Control Center (MCC). Each MOD organization was asked to identify projects that would help them attain a goal of a 30% reduction in operating costs by 2012. The MOD Operations and Planning organization responded to this challenge by launching several software automation projects that would allow them to greatly improve ISS console operations and reduce staffing and operating costs. These projects to date have allowed the MOD Operations organization to remove one full time (7 x 24 x 365) ISS console position in 2010; with the plan of eliminating two full time ISS console support positions by 2012. This will account for an overall 10 EP reduction in staffing for the Operations and Planning organization. These automation projects focused on utilizing software to automate many administrative and often repetitive tasks involved with processing ISS planning and daily operations information. This information was exchanged between the ground flight control teams in Houston and around the globe, as well as with the ISS astronaut crew. These tasks ranged from managing mission plan changes from around the globe, to uploading and downloading information to and from the ISS crew, to even more complex tasks that required multiple decision points to process the data, track approvals and deliver it to the correct recipient across network and security boundaries. The software solutions leveraged several different technologies including customized web applications and implementation of industry standard web services architecture between several planning tools; as well as a engaging a previously research level technology (TRL 2-3) developed by Ames Research Center (ARC) that utilized an intelligent agent based system to manage and automate file traffic flow, archiving f data, and generating console logs. This technology called OCAMS (OCA (Orbital Communication System) Management System), is now considered TRL level 9 and is in daily use in the Mission Control Center in support of ISS operations. These solutions have not only allowed for improved efficiency on console; but since many of the previously manual data transfers are now automated, many of the human error prone steps have been removed, and the quality of the planning products has improved tremendously. This has also allowed our Planning Flight Controllers more time to focus on the abstract areas of the job, (like the complexities of planning a mission for 6 international crew members with a global planning team), instead of being burdened with the administrative tasks that took significant time each console shift to process. The resulting automation solutions have allowed the Operations and Planning organization to realize significant cost savings for the ISS program through 2020 and many of these solutions could be a viable

Task automation in a successful industrial telerobot

NASA Technical Reports Server (NTRS)

Spelt, Philip F.; Jones, Sammy L.

1994-01-01

In this paper, we discuss cooperative work by Oak Ridge National Laboratory and Remotec, Inc., to automate components of the operator's workload using Remotec's Andros telerobot, thereby providing an enhanced user interface which can be retrofit to existing fielded units as well as being incorporated into new production units. Remotec's Andros robots are presently used by numerous electric utilities to perform tasks in reactors where substantial exposure to radiation exists, as well as by the armed forces and numerous law enforcement agencies. The automation of task components, as well as the video graphics display of the robot's position in the environment, will enhance all tasks performed by these users, as well as enabling performance in terrain where the robots cannot presently perform due to lack of knowledge about, for instance, the degree of tilt of the robot. Enhanced performance of a successful industrial mobile robot leads to increased safety and efficiency of performance in hazardous environments. The addition of these capabilities will greatly enhance the utility of the robot, as well as its marketability.

The Challenge of Planning and Execution for Spacecraft Mobile Robots

NASA Technical Reports Server (NTRS)

Dorais, Gregory A.; Gawdiak, Yuri; Clancy, Daniel (Technical Monitor)

2002-01-01

The need for spacecraft mobile robots continues to grow. These robots offer the potential to increase the capability, productivity, and duration of space missions while decreasing mission risk and cost. Spacecraft Mobile Robots (SMRs) can serve a number of functions inside and outside of spacecraft from simpler tasks, such as performing visual diagnostics and crew support, to more complex tasks, such as performing maintenance and in-situ construction. One of the predominant challenges to deploying SMRs is to reduce the need for direct operator interaction. Teleoperation is often not practical due to the communication latencies incurred because of the distances involved and in many cases a crewmember would directly perform a task rather than teleoperate a robot to do it. By integrating a mixed-initiative constraint-based planner with an executive that supports adjustably autonomous control, we intend to demonstrate the feasibility of autonomous SMRs by deploying one inside the International Space Station (ISS) and demonstrate in simulation one that operates outside of the ISS. This paper discusses the progress made at NASA towards this end, the challenges ahead, and concludes with an invitation to the research community to participate.

Ergonomic Analysis of the Work Condition in Aluminum Crafts Industry

NASA Astrophysics Data System (ADS)

Soewardi, H.; Taufiq, A.; Pradipta, T.

2017-12-01

Indonesia has plenty of abundant natural wealth. This natural wealth produces natural materials that can be utilized as a craft product. The craft workers generally still work manually and the work is done repeatedly in one cycle so it is very susceptible to musculoskeletal disorders. Musculoskeletal disorders will cause decrease of worker’s effectiveness and efficiency in completing the task. Thus, this fact has some adverse impact for the company. The purpose of this study is to analyze some task in manufacturing a traditional cooking tool (griddle) which encompasses mold of the griddle, refine of the griddle and the finishing touch by using the Occupational Repetitive Action Index (OCRA index) method. This method consists of high frequency movements, large forces, awkward postures, insufficient resting time and other factor such as vibration. Result of this study shows that in the molding operation, the worker has uncertain and medium risk on right hand in manufacturing small and large size of griddle with OCRA index is 2.5 and 5.3 respectively. In the refining operation the worker has light and medium risk on left hand in manufacturing small and large size with OCRA index is 3.6 and 5.8 using grinding machine and 5.8, 5.2, 6.3 and 5.0 using miser tool. In finishing operation, the worker has high risk on right hand in numbering of code griddle and has medium risk on right hand and medium on left hand in labeling with OCRA index is 9, 6.1 and 6.8 While in assembling operation the worker has no risk. Score that it indicates the risk level of the task in such job. Thus the following actions are to improve the work condition ergonomicly in all operation in alumunium craft.

Two Approaches to Measuring Task Interdependence in Elementary Schools.

ERIC Educational Resources Information Center

Charters, W. W., Jr.

This report compares two approaches to measuring task interdependence, a theoretically fruitful concept for analyzing an organization's technical system. Task interdependence exists among operating personnel in the degree that task performance of one operative constrains, augments, or otherwise poses contingencies for the performance of another.…

Evaluation of expert system application based on usability aspects

NASA Astrophysics Data System (ADS)

Munaiseche, C. P. C.; Liando, O. E. S.

2016-04-01

Usability usually defined as a point of human acceptance to a product or a system based on understands and right reaction to an interface. The performance of web application has been influence by the quality of the interface of that web to supporting information transfer process. Preferably, before the applications of expert systems were installed in the operational environment, these applications must be evaluated first by usability testing. This research aimed to measure the usability of the expert system application using tasks as interaction media. This study uses an expert system application to diagnose skin disease in human using questionnaire method which utilize the tasks as interaction media in measuring the usability. Certain tasks were executed by the participants in observing usability value of the application. The usability aspects observed were learnability, efficiency, memorability, errors, and satisfaction. Each questionnaire question represent aspects of usability. The results present the usability value for each aspect and the total average merit for all the five-usability aspect was 4.28, this indicated that the tested expert system application is in the range excellent for the usability level, so the application can be implemented as the operated system by user. The main contribution of the study is the research became the first step in using task model in the usability evaluation for the expert system application software.

Quality Evaluation of Land-Cover Classification Using Convolutional Neural Network

NASA Astrophysics Data System (ADS)

Dang, Y.; Zhang, J.; Zhao, Y.; Luo, F.; Ma, W.; Yu, F.

2018-04-01

Land-cover classification is one of the most important products of earth observation, which focuses mainly on profiling the physical characters of the land surface with temporal and distribution attributes and contains the information of both natural and man-made coverage elements, such as vegetation, soil, glaciers, rivers, lakes, marsh wetlands and various man-made structures. In recent years, the amount of high-resolution remote sensing data has increased sharply. Accordingly, the volume of land-cover classification products increases, as well as the need to evaluate such frequently updated products that is a big challenge. Conventionally, the automatic quality evaluation of land-cover classification is made through pixel-based classifying algorithms, which lead to a much trickier task and consequently hard to keep peace with the required updating frequency. In this paper, we propose a novel quality evaluation approach for evaluating the land-cover classification by a scene classification method Convolutional Neural Network (CNN) model. By learning from remote sensing data, those randomly generated kernels that serve as filter matrixes evolved to some operators that has similar functions to man-crafted operators, like Sobel operator or Canny operator, and there are other kernels learned by the CNN model that are much more complex and can't be understood as existing filters. The method using CNN approach as the core algorithm serves quality-evaluation tasks well since it calculates a bunch of outputs which directly represent the image's membership grade to certain classes. An automatic quality evaluation approach for the land-cover DLG-DOM coupling data (DLG for Digital Line Graphic, DOM for Digital Orthophoto Map) will be introduced in this paper. The CNN model as an robustness method for image evaluation, then brought out the idea of an automatic quality evaluation approach for land-cover classification. Based on this experiment, new ideas of quality evaluation of DLG-DOM coupling land-cover classification or other kinds of labelled remote sensing data can be further studied.

From Apollo to Cognac

NASA Technical Reports Server (NTRS)

1980-01-01

Shell Oil Company started oil and gas production from a new offshore platform called Cognac located in the Gulf of Mexico. It is the world's tallest oil platform, slightly taller than the Empire State Building. The highly complex job of installing Cognac's support "jacket" under water more than a thousand feet deep was directed from a barge-based control center. To enable crews to practice in advance difficult tasks never before accomplished, Honeywell, adapting NASA's Apollo technology, developed a system for simulating the various underwater operations. In training sessions, displays and controls reacted exactly as they would in real operation.

The multi-attribute task battery for human operator workload and strategic behavior research

NASA Technical Reports Server (NTRS)

Comstock, J. Raymond, Jr.; Arnegard, Ruth J.

1992-01-01

The Multi-Attribute Task (MAT) Battery provides a benchmark set of tasks for use in a wide range of lab studies of operator performance and workload. The battery incorporates tasks analogous to activities that aircraft crewmembers perform in flight, while providing a high degree of experimenter control, performance data on each subtask, and freedom to use nonpilot test subjects. Features not found in existing computer based tasks include an auditory communication task (to simulate Air Traffic Control communication), a resource management task permitting many avenues or strategies of maintaining target performance, a scheduling window which gives the operator information about future task demands, and the option of manual or automated control of tasks. Performance data are generated for each subtask. In addition, the task battery may be paused and onscreen workload rating scales presented to the subject. The MAT Battery requires a desktop computer with color graphics. The communication task requires a serial link to a second desktop computer with a voice synthesizer or digitizer card.

The Multi-Attribute Task Battery II (MATB-II) Software for Human Performance and Workload Research: A User's Guide

NASA Technical Reports Server (NTRS)

Santiago-Espada, Yamira; Myer, Robert R.; Latorella, Kara A.; Comstock, James R., Jr.

2011-01-01

The Multi-Attribute Task Battery (MAT Battery). is a computer-based task designed to evaluate operator performance and workload, has been redeveloped to operate in Windows XP Service Pack 3, Windows Vista and Windows 7 operating systems.MATB-II includes essentially the same tasks as the original MAT Battery, plus new configuration options including a graphical user interface for controlling modes of operation. MATB-II can be executed either in training or testing mode, as defined by the MATB-II configuration file. The configuration file also allows set up of the default timeouts for the tasks, the flow rates of the pumps and tank levels of the Resource Management (RESMAN) task. MATB-II comes with a default event file that an experimenter can modify and adapt

Object as a model of intelligent robot in the virtual workspace

NASA Astrophysics Data System (ADS)

Foit, K.; Gwiazda, A.; Banas, W.; Sekala, A.; Hryniewicz, P.

2015-11-01

The contemporary industry requires that every element of a production line will fit into the global schema, which is connected with the global structure of business. There is the need to find the practical and effective ways of the design and management of the production process. The term “effective” should be understood in a manner that there exists a method, which allows building a system of nodes and relations in order to describe the role of the particular machine in the production process. Among all the machines involved in the manufacturing process, industrial robots are the most complex ones. This complexity is reflected in the realization of elaborated tasks, involving handling, transporting or orienting the objects in a work space, and even performing simple machining processes, such as deburring, grinding, painting, applying adhesives and sealants etc. The robot also performs some activities connected with automatic tool changing and operating the equipment mounted on the wrist of the robot. Because of having the programmable control system, the robot also performs additional activities connected with sensors, vision systems, operating the storages of manipulated objects, tools or grippers, measuring stands, etc. For this reason the description of the robot as a part of production system should take into account the specific nature of this machine: the robot is a substitute of a worker, who performs his tasks in a particular environment. In this case, the model should be able to characterize the essence of "employment" in the sufficient way. One of the possible approaches to this problem is to treat the robot as an object, in the sense often used in computer science. This allows both: to describe certain operations performed on the object, as well as describing the operations performed by the object. This paper focuses mainly on the definition of the object as the model of the robot. This model is confronted with the other possible descriptions. The results can be further used during designing of the complete manufacturing system, which takes into account all the involved machines and has the form of an object-oriented model.

Operational Readiness Review Plan for the Radioisotope Thermoelectric Generator Materials Production Tasks

DOE R&D Accomplishments Database

Cooper, R. H.; Martin, M. M.; Riggs, C. R.; Beatty, R. L.; Ohriner, E. K.; Escher, R. N.

1990-04-19

In October 1989, a US shuttle lifted off from Cape Kennedy carrying the spacecraft Galileo on its mission to Jupiter. In November 1990, a second spacecraft, Ulysses, will be launched from Cape Kennedy with a mission to study the polar regions of the sun. The prime source of power for both spacecraft is a series of radioisotope thermoelectric generators (RTGs), which use plutonium oxide (plutonia) as a heat source. Several of the key components in this power system are required to ensure the safety of both the public and the environment and were manufactured at Oak Ridge National Laboratory (ORNL) in the 1980 to 1983 period. For these two missions, Martin Marietta Energy Systems, Inc. (Energy Systems), will provide an iridium alloy component used to contain the plutonia heat source and a carbon composite material that serves as a thermal insulator. ORNL alone will continue to fabricate the carbon composite material. Because of the importance to DOE that Energy Systems deliver these high quality components on time, performance of an Operational Readiness Review (ORR) of these manufacturing activities is necessary. Energy Systems Policy GP 24 entitled "Operational Readiness Process" describes the formal and comprehensive process by which appropriate Energy Systems activities are to be reviewed to ensure their readiness. This Energy System policy is aimed at reducing the risks associated with mission success and requires a management approved "readiness plan" to be issued. This document is the readiness plan for the RTG materials production tasks.

[Modern operations management in workflow operation. Spectrum of responsibilities and challenges for the future].

PubMed

Riedl, S

2002-02-01

The operating unit is one of the cost-intensive facilities in a surgical clinic with a pacemaking function for most of the internal procedures. The power of performance of the operating unit is based on the co-operation of all disciplines and professions involved. The key to management of the operating unit is not only to co-ordinate the daily procedures, but also to interact with support personnel. To ensure successful OR management, the internal structure of the OR must fit the clinical tasks and the available quantity of personnel in each profession must be co-ordinated. Sufficient utilization of resources and equipment must be guaranteed without cost-intensive over-capacities and patient flow must be orientated to OR capacities. The development of such a business structure requires the management to clearly define the goal, to know the actual on-site data in detail with regard to the idiosyncratic workings of each speciality and to clearly assign the competence of each member of the team working in the OR. Co-ordination of the operating unit is the main task of OR management, which must ensure the following: transparent and co-ordinated schedule management in the various operative specialities, goal-directed changes of the schedule with incorporation of emergencies, as well as effective organization of staff. In order to realize these tasks, it is reasonable to implement interdisciplinary rules of procedures. In addition, the assignment of a neutral decision-making body within the OR and the creation of an information center for all OR personnel. The challenge of OR organization in the future is to implement more effective documentation systems and active controlling within the OR. One can ensure adequate utilization of resources in the OR with prospectively oriented planning. Better transparence of operations in the OR contributes to increased efficiency. Implementation of quality management is the foundation for a successfully operating surgical hospital. Not only the productivity of individual members of the staff, but also the precise documentation of the quality of results will become important parameters in a successful surgical hospital, whose nucleus is the OR.

Modern laser technologies used for cutting textile materials

NASA Astrophysics Data System (ADS)

Isarie, Claudiu; Dragan, Anca; Isarie, Laura; Nastase, Dan

2006-02-01

With modern laser technologies we can cut multiple layers at once, yielding high production levels and short setup times between cutting runs. One example could be the operation of cutting the material named Nylon 66, used to manufacture automobile airbags. With laser, up to seven layers of Nylon 66 can be cut in one pass, that means high production rates on a single machine. Airbags must be precisely crafted piece of critical safety equipment that is built to very high levels of precision in a mass production environment. Of course, synthetic material, used for airbags, can be cut also by a conventional fixed blade system, but for a high production rates and a long term low-maintenance, laser cutting is most suitable. Most systems, are equipped with two material handling systems, which can cut on one half of he table while the finished product is being removed from the other half and the new stock material laid out. The laser system is reliable and adaptable to any flatbed-cutting task. Computer controlled industrial cutting and plotting machines are the latest offerings from a well established and experienced industrial engineering company that is dedicated to reduce cutting costs and boosting productivity in today's competitive industrial machine tool market. In this way, just one machine can carry out a multitude of production tasks. Authors have studied the cutting parameters for different textile materials, to reach the maximum output of the process.

Civil use of night vision goggles within the National Airspace System

NASA Astrophysics Data System (ADS)

Winkel, James G.; Faber, Lorelei

2001-08-01

When properly employed, Night Vision Goggles (NVGs) improve a pilot's ability to see during periods of darkness. The resultant enhancement in situational awareness achieved when using NVGs, increases light safety during night VFR operations. FAA is constrained with a lack of requisite regulatory and guidance infrastructure to adequately facilitate the civil request for use in NVGs within the National Airspace System (NAS) Appliances and Equipment, is formed and tasked to develop: operational concept and operational requirements for NVG implementation into the NAS, minimum operational performance standards for NVGs, and training guidelines and considerations for NVG operations. This paper provides a historical perspective on use of NVGs within the NAS, the status of SC-196 work in progress, FAA integration of SC-196 committee products and the harmonization effort between EUROCAEs NVG committee and SC- 196.

Space station operations task force summary report

NASA Technical Reports Server (NTRS)

1987-01-01

A companion to the Space Stations Operation Task Force Panels' Reports, this document summarizes all space station program goals, operations, and the characteristics of the expected user community. Strategies for operation and recommendations for implementation are included.

SenThIS - Sentinels of Thuringian information systems

NASA Astrophysics Data System (ADS)

Naue, Sandra; Krause, Peter

2016-04-01

Decision-making for sustainable environmental resource management or risk prevention is facing the problem of constantly changing conditions related to the projected changes of climate, demography and socio-economy. Herefore, adaptable tools and methods which can reflect such changes are needed for an efficient management. The need to improve existing tools is a challenge the departments of German environmental authorities at state and federal level are facing at this time. Additionally the increasing demands for work process optimization due to financial cutbacks are coming into play. Consequently the need for suitable adaptation measurements for short and long term changes of environmental state variables is growing. The importance of spatio-temporal data, providing continuous observation about the state of the environmental system and its changes, is therefore increasing in order to elaborate adaptation strategies. In this case earth observation is a useful source for the required data. With the new Sentinel fleet, ESA's Copernicus Program is providing a possibility to obtain such information free in high temporal and spatial resolution. The BMVI funded project SenThIS, a collaborative project by the Thuringian State Institute for Environment and Geology (TLUG), the Thuringian Forest Department and two SMEs EOS GmbH and Feiffer consult is aiming at utilizing Copernicus data and services for operational tasks on a federal level. It addresses this aforementioned deficit through the development and implementation of a processing chain for synergetic and automated application of remote sensing data and products to accomplish operational state tasks. The product development is characterized by the synergetic application of remote sensing data and suitable models. Design and calibration of the models base on Sentinel 1/2 data and additional information (e.g. meteorological data, in-situ measurements). This results in products of highly temporal and spatial resolution for entire Thuringia. Simultaneously a performance evaluation of the developed products as well as the establishment of those products and other suitable Copernicus services in form of an operational application of public tasks should be reached. Within the project framework prototypical remote sensing products for state authorities will be developed. In particular, a soil moisture product derived by process oriented modelling utilizing remote sensing data that is going to provide updated comprehensive information at a three to six day interval will be developed. The development will be accompanied by detailed evaluation, validation and uncertainty analysis using various information from different sources. The soil moisture product is expected to help in the improvement of the established flood forecast systems, crop yield estimation or forestal state reviews. Additional products like a snow product or the derivation of agricultural stock parameters will be developed or gained from existing Copernicus products. By the resulting data and processing infrastructure SenThIS enables the involved authorities to work faster and more efficient. Thereby a better forecast, detection and reaction to environmental risks and potential catastrophes will become possible. The poster presents the underlying idea and structure of the SenThIS project along with the first results of the first project year.

The Role of Task Type in Foreign Language Written Production: Focusing on Fluency, Complexity, and Accuracy

ERIC Educational Resources Information Center

Rezazadeh, Mohsen; Tavakoli, Mansoor; Rasekh, Abbas Eslami

2011-01-01

The aim of this study was to investigate the effects of two task types on foreign language written production. Particularly it addressed the issue of how three aspects of language production (i.e. fluency, complexity, and accuracy) vary among two different task types (i.e. argumentative writing task and instruction writing task). One hundred sixty…

Task planning and control synthesis for robotic manipulation in space applications

NASA Technical Reports Server (NTRS)

Sanderson, A. C.; Peshkin, M. A.; Homem-De-mello, L. S.

1987-01-01

Space-based robotic systems for diagnosis, repair and assembly of systems will require new techniques of planning and manipulation to accomplish these complex tasks. Results of work in assembly task representation, discrete task planning, and control synthesis which provide a design environment for flexible assembly systems in manufacturing applications, and which extend to planning of manipulatiuon operations in unstructured environments are summarized. Assembly planning is carried out using the AND/OR graph representation which encompasses all possible partial orders of operations and may be used to plan assembly sequences. Discrete task planning uses the configuration map which facilitates search over a space of discrete operations parameters in sequential operations in order to achieve required goals in the space of bounded configuration sets.

Development of human factors guidelines for advanced traveler information systems and commercial vehicle operations : task analysis of ATIS/CVO functions

DOT National Transportation Integrated Search

1996-11-01

This working paper documents Task E of the present project, Task Analyses for Advanced Traveler Information Systems (ATIS) and Commercial Vehicle Operations (CVO) systems. The goal of Task E is to conduct detailed analyses of the influence of using A...

Temporal Prediction Errors Affect Short-Term Memory Scanning Response Time.

PubMed

Limongi, Roberto; Silva, Angélica M

2016-11-01

The Sternberg short-term memory scanning task has been used to unveil cognitive operations involved in time perception. Participants produce time intervals during the task, and the researcher explores how task performance affects interval production - where time estimation error is the dependent variable of interest. The perspective of predictive behavior regards time estimation error as a temporal prediction error (PE), an independent variable that controls cognition, behavior, and learning. Based on this perspective, we investigated whether temporal PEs affect short-term memory scanning. Participants performed temporal predictions while they maintained information in memory. Model inference revealed that PEs affected memory scanning response time independently of the memory-set size effect. We discuss the results within the context of formal and mechanistic models of short-term memory scanning and predictive coding, a Bayes-based theory of brain function. We state the hypothesis that our finding could be associated with weak frontostriatal connections and weak striatal activity.

Low-cost solar array project progress and plans

NASA Technical Reports Server (NTRS)

Callaghan, W. T.

1981-01-01

The considered project is part of the DOE Photovoltaic Technology and Market Development Program. This program is concerned with the development and the utilization of cost-competitive photovoltaic systems. The project has the objective to develop, by 1986, the national capability to manufacture low-cost, long-life photovoltaic arrays at production rates that will realize economies of scale, and at a price of less than $0.70/watt. The array performance objectives include an efficiency greater than 10% and an operating lifetime longer than 20 years. The objective of the silicon material task is to establish the practicality of processes for producing silicon suitable for terrestrial photovoltaic applications at a price of $14/kg. The large-area sheet task is concerned with the development of process technology for sheet formation. Low-cost encapsulation material systems are being developed in connection with the encapsulation task. Another project goal is related to the development of economical process sequences.

Performing a local barrier operation

DOEpatents

Archer, Charles J; Blocksome, Michael A; Ratterman, Joseph D; Smith, Brian E

2014-03-04

Performing a local barrier operation with parallel tasks executing on a compute node including, for each task: retrieving a present value of a counter; calculating, in dependence upon the present value of the counter and a total number of tasks performing the local barrier operation, a base value, the base value representing the counter's value prior to any task joining the local barrier; calculating, in dependence upon the base value and the total number of tasks performing the local barrier operation, a target value of the counter, the target value representing the counter's value when all tasks have joined the local barrier; joining the local barrier, including atomically incrementing the value of the counter; and repetitively, until the present value of the counter is no less than the target value of the counter: retrieving the present value of the counter and determining whether the present value equals the target value.

Performing a local barrier operation

DOEpatents

Archer, Charles J; Blocksome, Michael A; Ratterman, Joseph D; Smith, Brian E

2014-03-04

Performing a local barrier operation with parallel tasks executing on a compute node including, for each task: retrieving a present value of a counter; calculating, in dependence upon the present value of the counter and a total number of tasks performing the local barrier operation, a base value of the counter, the base value representing the counter's value prior to any task joining the local barrier; calculating, in dependence upon the base value and the total number of tasks performing the local barrier operation, a target value, the target value representing the counter's value when all tasks have joined the local barrier; joining the local barrier, including atomically incrementing the value of the counter; and repetitively, until the present value of the counter is no less than the target value of the counter: retrieving the present value of the counter and determining whether the present value equals the target value.

Telerobot control system

NASA Technical Reports Server (NTRS)

Backes, Paul G. (Inventor); Tso, Kam S. (Inventor)

1993-01-01

This invention relates to an operator interface for controlling a telerobot to perform tasks in a poorly modeled environment and/or within unplanned scenarios. The telerobot control system includes a remote robot manipulator linked to an operator interface. The operator interface includes a setup terminal, simulation terminal, and execution terminal for the control of the graphics simulator and local robot actuator as well as the remote robot actuator. These terminals may be combined in a single terminal. Complex tasks are developed from sequential combinations of parameterized task primitives and recorded teleoperations, and are tested by execution on a graphics simulator and/or local robot actuator, together with adjustable time delays. The novel features of this invention include the shared and supervisory control of the remote robot manipulator via operator interface by pretested complex tasks sequences based on sequences of parameterized task primitives combined with further teleoperation and run-time binding of parameters based on task context.

Lessons Learned on Implementing Fault Detection, Isolation, and Recovery (FDIR) in a Ground Launch Environment

NASA Technical Reports Server (NTRS)

Ferrell, Bob A.; Lewis, Mark E.; Perotti, Jose M.; Brown, Barbara L.; Oostdyk, Rebecca L.; Goetz, Jesse W.

2010-01-01

This paper's main purpose is to detail issues and lessons learned regarding designing, integrating, and implementing Fault Detection Isolation and Recovery (FDIR) for Constellation Exploration Program (CxP) Ground Operations at Kennedy Space Center (KSC). Part of the0 overall implementation of National Aeronautics and Space Administration's (NASA's) CxP, FDIR is being implemented in three main components of the program (Ares, Orion, and Ground Operations/Processing). While not initially part of the design baseline for the CxP Ground Operations, NASA felt that FDIR is important enough to develop, that NASA's Exploration Systems Mission Directorate's (ESMD's) Exploration Technology Development Program (ETDP) initiated a task for it under their Integrated System Health Management (ISHM) research area. This task, referred to as the FDIIR project, is a multi-year multi-center effort. The primary purpose of the FDIR project is to develop a prototype and pathway upon which Fault Detection and Isolation (FDI) may be transitioned into the Ground Operations baseline. Currently, Qualtech Systems Inc (QSI) Commercial Off The Shelf (COTS) software products Testability Engineering and Maintenance System (TEAMS) Designer and TEAMS RDS/RT are being utilized in the implementation of FDI within the FDIR project. The TEAMS Designer COTS software product is being utilized to model the system with Functional Fault Models (FFMs). A limited set of systems in Ground Operations are being modeled by the FDIR project, and the entire Ares Launch Vehicle is being modeled under the Functional Fault Analysis (FFA) project at Marshall Space Flight Center (MSFC). Integration of the Ares FFMs and the Ground Processing FFMs is being done under the FDIR project also utilizing the TEAMS Designer COTS software product. One of the most significant challenges related to integration is to ensure that FFMs developed by different organizations can be integrated easily and without errors. Software Interface Control Documents (ICDs) for the FFMs and their usage will be addressed as the solution to this issue. In particular, the advantages and disadvantages of these ICDs across physically separate development groups will be delineated.

Cognitive consequences of clumsy automation on high workload, high consequence human performance

NASA Technical Reports Server (NTRS)

Cook, Richard I.; Woods, David D.; Mccolligan, Elizabeth; Howie, Michael B.

1991-01-01

The growth of computational power has fueled attempts to automate more of the human role in complex problem solving domains, especially those where system faults have high consequences and where periods of high workload may saturate the performance capacity of human operators. Examples of these domains include flightdecks, space stations, air traffic control, nuclear power operation, ground satellite control rooms, and surgical operating rooms. Automation efforts may have unanticipated effects on human performance, particularly if they increase the workload at peak workload times or change the practitioners' strategies for coping with workload. Smooth and effective changes in automation requires detailed understanding of the congnitive tasks confronting the user: it has been called user centered automation. The introduction of a new computerized technology in a group of hospital operating rooms used for heart surgery was observed. The study revealed how automation, especially 'clumsy automation', effects practitioner work patterns and suggest that clumsy automation constrains users in specific and significant ways. Users tailor both the new system and their tasks in order to accommodate the needs of process and production. The study of this tailoring may prove a powerful tool for exposing previously hidden patterns of user data processing, integration, and decision making which may, in turn, be useful in the design of more effective human-machine systems.

HURON (HUman and Robotic Optimization Network) Multi-Agent Temporal Activity Planner/Scheduler

NASA Technical Reports Server (NTRS)

Hua, Hook; Mrozinski, Joseph J.; Elfes, Alberto; Adumitroaie, Virgil; Shelton, Kacie E.; Smith, Jeffrey H.; Lincoln, William P.; Weisbin, Charles R.

2012-01-01

HURON solves the problem of how to optimize a plan and schedule for assigning multiple agents to a temporal sequence of actions (e.g., science tasks). Developed as a generic planning and scheduling tool, HURON has been used to optimize space mission surface operations. The tool has also been used to analyze lunar architectures for a variety of surface operational scenarios in order to maximize return on investment and productivity. These scenarios include numerous science activities performed by a diverse set of agents: humans, teleoperated rovers, and autonomous rovers. Once given a set of agents, activities, resources, resource constraints, temporal constraints, and de pendencies, HURON computes an optimal schedule that meets a specified goal (e.g., maximum productivity or minimum time), subject to the constraints. HURON performs planning and scheduling optimization as a graph search in state-space with forward progression. Each node in the graph contains a state instance. Starting with the initial node, a graph is automatically constructed with new successive nodes of each new state to explore. The optimization uses a set of pre-conditions and post-conditions to create the children states. The Python language was adopted to not only enable more agile development, but to also allow the domain experts to easily define their optimization models. A graphical user interface was also developed to facilitate real-time search information feedback and interaction by the operator in the search optimization process. The HURON package has many potential uses in the fields of Operations Research and Management Science where this technology applies to many commercial domains requiring optimization to reduce costs. For example, optimizing a fleet of transportation truck routes, aircraft flight scheduling, and other route-planning scenarios involving multiple agent task optimization would all benefit by using HURON.

Maintenance and operations tasks accomplished at DSS 12 during the antenna panel replacement downtime

NASA Technical Reports Server (NTRS)

Butcher, L.; Jonas, T.; Wood, W.

1982-01-01

The heavy schedule of tracking activities at the Echo Deep Space Station (DSS 12) prevents some time-consuming maintenance tasks from being performed. Careful coordination prior to and during a mandatory task (antenna panel replacement) made it possible to do a large number of unrelated tasks that ordinarily would have to be deferred. The maintenance and operations tasks accomplished during the downtime are described.

Adjustable control station with movable monitors and cameras for viewing systems in robotics and teleoperations

NASA Technical Reports Server (NTRS)

Diner, Daniel B. (Inventor)

1994-01-01

Real-time video presentations are provided in the field of operator-supervised automation and teleoperation, particularly in control stations having movable cameras for optimal viewing of a region of interest in robotics and teleoperations for performing different types of tasks. Movable monitors to match the corresponding camera orientations (pan, tilt, and roll) are provided in order to match the coordinate systems of all the monitors to the operator internal coordinate system. Automated control of the arrangement of cameras and monitors, and of the configuration of system parameters, is provided for optimal viewing and performance of each type of task for each operator since operators have different individual characteristics. The optimal viewing arrangement and system parameter configuration is determined and stored for each operator in performing each of many types of tasks in order to aid the automation of setting up optimal arrangements and configurations for successive tasks in real time. Factors in determining what is optimal include the operator's ability to use hand-controllers for each type of task. Robot joint locations, forces and torques are used, as well as the operator's identity, to identify the current type of task being performed in order to call up a stored optimal viewing arrangement and system parameter configuration.

Assessment of Occupational Exposure to Bisphenol A in Five Different Production Companies in Finland.

PubMed

Heinälä, Milla; Ylinen, Katriina; Tuomi, Tapani; Santonen, Tiina; Porras, Simo P

2017-01-01

The aim of the study was to assess occupational exposure to bisphenol A in Finland. Five companies took part in the research project: two paint factories (liquid and powder paints), a composite product factory, a thermal paper factory, and a tractor factory. Exposure was assessed by measuring total bisphenol A excretion (free and conjugated) from urine samples, and its concentrations in the air. The results revealed the specific work tasks in two of five companies in which significant occupational exposure to bisphenol A may occur. In the manufacturing of liquid paint hardener, urine samples collected after the working day showed bisphenol A levels of up to 100-170 µg l-1. Workers in thermal paper manufacturing were also exposed to bisphenol A, especially those working in the manufacture of coating material and operating coating machines. Median concentrations of the post-shift urine samples of coating machine workers were in the range of 130-250 µg l-1. The highest bisphenol A concentrations were in the range of 1000-1500 µg l-1. Recommendations for more effective personal protection resulted in decreased exposure, particularly among coating machine operators. In the rest of the companies, urinary bisphenol A levels were typically in the range of those of the general population. Bisphenol A concentrations in air samples were typically low (<40 µg m-3), except in some short-term duties related to the handling of solid bisphenol A (maximum 17.6 mg m-3). Low air levels, even in the companies with high urinary levels, suggest exposure via dermal contact. According to the results, exposure to bisphenol A may occur particularly in work tasks that involve the use of pure bisphenol A. In these tasks, special attention should be paid to the prevention of skin exposure. Inhalation exposure may become relevant in dusty work tasks. Since skin exposure is of potential concern in these tasks, biomonitoring is recommended as the method for assessing occupational exposure to bisphenol A. © The Author 2017. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Effects of System Timing Parameters on Operator Performance in a Personnel Records Task

DTIC Science & Technology

1981-03-01

work sampling, embedded performance measures, and operator satisfaction ratings) are needed to provide a complete analysis of the effects of the four...HFL-8 l-l/NPRDC-8 1-1 March 1981 EFFECTS OF SYSTEM TIMING PARAMETERS ON OPERATOR PERFORMANCE IN A PERSONNEL RECORDS TASK Robert C. Williges Beverly H...and Subtitle) S. TYPE OF REPORT & PERIOD COVERED EFFECTS OF SYSTEM TIMING PARAMETERS ON OPERATOR PERFORMANCE IN A PERSONNEL RECORDS TASK Final

The knowledge-based framework for a nuclear power plant operator advisor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, D.W.; Hajek, B.K.

1989-01-01

An important facet in the design, development, and evaluation of aids for complex systems is the identification of the tasks performed by the operator. Operator aids utilizing artificial intelligence, or more specifically knowledge-based systems, require identification of these tasks in the context of a knowledge-based framework. In this context, the operator responses to the plant behavior are to monitor and comprehend the state of the plant, identify normal and abnormal plant conditions, diagnose abnormal plant conditions, predict plant response to specific control actions, and select the best available control action, implement a feasible control action, monitor system response to themore » control action, and correct for any inappropriate responses. These tasks have been identified to formulate a knowledge-based framework for an operator advisor under development at Ohio State University that utilizes the generic task methodology proposed by Chandrasekaran. The paper lays the foundation to identify the responses as a knowledge-based set of tasks in accordance with the expected human operator responses during an event. Initial evaluation of the expert system indicates the potential for an operator aid that will improve the operator's ability to respond to both anticipated and unanticipated events.« less

The role of the production scheduling system in rescheduling

NASA Astrophysics Data System (ADS)

Kalinowski, K.; Grabowik, C.; Kempa, W.; Paprocka, I.

2015-11-01

The paper presents the rescheduling problem in the context of cooperation between production scheduling system (PSS) and other units in an integrated manufacturing environment - decision makers and software systems. The main aim is to discuss the PSS functionality for maximizing automation of the rescheduling process, reducing the response time and improving the quality of generated solutions. PSSs operate in the meeting of tactical and operational level of planning and control, and play an important role in the production preparation and control. On the basis of information about orders, technology and production system state (e.g. resources availability) they prepare and/or update a detailed plan of production flow - a schedule. All necessary data for scheduling and rescheduling are usually collected in other systems both from organizational and technical production preparation, e.g. ERP, PLM, MES, CAPP or others, as well as they are entered directly by the decision- makers/operators. Data acquired in this way are often incomplete and inconsistent. Therefore the existing rescheduling software works according to interactive method - rather support but does not replace the human decision maker in tasks planning. When rescheduling, due to the limited amount of time to make a decision this interaction is particularly important. An additional problem arises in data acquisition, in the process of data exchanging between systems or in the identification of new data sources and their processing. Different approaches to rescheduling were characterized, including those solutions, where all these operations are carried out by an autonomous system and those in which scheduling is performed only upon request from the outside, for the newly created scheduling data representing the current state of the production system.

Experiences Supporting the Lunar Reconnaissance Orbiter Camera: the Devops Model

NASA Astrophysics Data System (ADS)

Licht, A.; Estes, N. M.; Bowman-Cisnesros, E.; Hanger, C. D.

2013-12-01

Introduction: The Lunar Reconnaissance Orbiter Camera (LROC) Science Operations Center (SOC) is responsible for instrument targeting, product processing, and archiving [1]. The LROC SOC maintains over 1,000,000 observations with over 300 TB of released data. Processing challenges compound with the acquisition of over 400 Gbits of observations daily creating the need for a robust, efficient, and reliable suite of specialized software. Development Environment: The LROC SOC's software development methodology has evolved over time. Today, the development team operates in close cooperation with the systems administration team in a model known in the IT industry as DevOps. The DevOps model enables a highly productive development environment that facilitates accomplishment of key goals within tight schedules[2]. The LROC SOC DevOps model incorporates industry best practices including prototyping, continuous integration, unit testing, code coverage analysis, version control, and utilizing existing open source software. Scientists and researchers at LROC often prototype algorithms and scripts in a high-level language such as MATLAB or IDL. After the prototype is functionally complete the solution is implemented as production ready software by the developers. Following this process ensures that all controls and requirements set by the LROC SOC DevOps team are met. The LROC SOC also strives to enhance the efficiency of the operations staff by way of weekly presentations and informal mentoring. Many small scripting tasks are assigned to the cognizant operations personnel (end users), allowing for the DevOps team to focus on more complex and mission critical tasks. In addition to leveraging open source software the LROC SOC has also contributed to the open source community by releasing Lunaserv [3]. Findings: The DevOps software model very efficiently provides smooth software releases and maintains team momentum. Scientists prototyping their work has proven to be very efficient as developers do not need to spend time iterating over small changes. Instead, these changes are realized in early prototypes and implemented before the task is seen by developers. The development practices followed by the LROC SOC DevOps team help facilitate a high level of software quality that is necessary for LROC SOC operations. Application to the Scientific Community: There is no replacement for having software developed by professional developers. While it is beneficial for scientists to write software, this activity should be seen as prototyping, which is then made production ready by professional developers. When constructed properly, even a small development team has the ability to increase the rate of software development for a research group while creating more efficient, reliable, and maintainable products. This strategy allows scientists to accomplish more, focusing on teamwork, rather than software development, which may not be their primary focus. 1. Robinson et al. (2010) Space Sci. Rev. 150, 81-124 2. DeGrandis. (2011) Cutter IT Journal. Vol 24, No. 8, 34-39 3. Estes, N.M.; Hanger, C.D.; Licht, A.A.; Bowman-Cisneros, E.; Lunaserv Web Map Service: History, Implementation Details, Development, and Uses, http://adsabs.harvard.edu/abs/2013LPICo1719.2609E.

Program on Earth Observation Data Management Systems (EODMS)

NASA Technical Reports Server (NTRS)

Eastwood, L. F., Jr.; Gohagan, J. K.; Hill, C. T.; Morgan, R. P.; Hays, T. R.; Ballard, R. J.; Crnkovick, G. R.; Schaeffer, M. A.

1976-01-01

An assessment was made of the needs of a group of potential users of satellite remotely sensed data (state, regional, and local agencies) involved in natural resources management in five states, and alternative data management systems to satisfy these needs are outlined. Tasks described include: (1) a comprehensive data needs analysis of state and local users; (2) the design of remote sensing-derivable information products that serve priority state and local data needs; (3) a cost and performance analysis of alternative processing centers for producing these products; (4) an assessment of the impacts of policy, regulation and government structure on implementing large-scale use of remote sensing technology in this community of users; and (5) the elaboration of alternative institutional arrangements for operational Earth Observation Data Management Systems (EODMS). It is concluded that an operational EODMS will be of most use to state, regional, and local agencies if it provides a full range of information services -- from raw data acquisition to interpretation and dissemination of final information products.

System Engineering for the NNSA Knowledge Base

NASA Astrophysics Data System (ADS)

Young, C.; Ballard, S.; Hipp, J.

2006-05-01

To improve ground-based nuclear explosion monitoring capability, GNEM R&E (Ground-based Nuclear Explosion Monitoring Research & Engineering) researchers at the national laboratories have collected an extensive set of raw data products. These raw data are used to develop higher level products (e.g. 2D and 3D travel time models) to better characterize the Earth at regional scales. The processed products and selected portions of the raw data are stored in an archiving and access system known as the NNSA (National Nuclear Security Administration) Knowledge Base (KB), which is engineered to meet the requirements of operational monitoring authorities. At its core, the KB is a data archive, and the effectiveness of the KB is ultimately determined by the quality of the data content, but access to that content is completely controlled by the information system in which that content is embedded. Developing this system has been the task of Sandia National Laboratories (SNL), and in this paper we discuss some of the significant challenges we have faced and the solutions we have engineered. One of the biggest system challenges with raw data has been integrating database content from the various sources to yield an overall KB product that is comprehensive, thorough and validated, yet minimizes the amount of disk storage required. Researchers at different facilities often use the same data to develop their products, and this redundancy must be removed in the delivered KB, ideally without requiring any additional effort on the part of the researchers. Further, related data content must be grouped together for KB user convenience. Initially SNL used whatever tools were already available for these tasks, and did the other tasks manually. The ever-growing volume of KB data to be merged, as well as a need for more control of merging utilities, led SNL to develop our own java software package, consisting of a low- level database utility library upon which we have built several applications for specific tasks (e.g an event/origin merger; a waveform merger). Our package now includes applications for nearly all of the KB merging tasks, but development continues with an emphasis on improving user interfaces by adding GUIs and on increasing performance. Not all types of data products are well-suited to storage and access from a relational database, because of their basic underlying structure as well as the performance requirements for their use. In some cases, such products already have a standard format and corresponding software library in the existing monitoring system, but for others, this is not the case. For some of the latter, SNL has developed a large and complex C++ library for storing and accessing a wide variety of interpolatable geophysical data. Our library was first developed to support kriging of empirical data to provide value corrections and uncertainty estimates for underlying base models. Operational performance constraints led to the addition of an optimal tessellation capability to deliver kriging results using the much faster natural-neighbor interpolation method. To provide better predictions in areas without well-recorded seismicity, the library was further enhanced to provide the capability to use complex polygon delimited regional models as a base model for a single station/phase. Our latest work has focused on improving system performance and flexibility by running the library as a server application on a dedicated multi-processor server. This work was supported by the United States Department of Energy under Contract DE-AC04-94AL85000. Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy.

Cognitive task load in a naval ship control centre: from identification to prediction.

PubMed

Grootjen, M; Neerincx, M A; Veltman, J A

Deployment of information and communication technology will lead to further automation of control centre tasks and an increasing amount of information to be processed. A method for establishing adequate levels of cognitive task load for the operators in such complex environments has been developed. It is based on a model distinguishing three load factors: time occupied, task-set switching, and level of information processing. Application of the method resulted in eight scenarios for eight extremes of task load (i.e. low and high values for each load factor). These scenarios were performed by 13 teams in a high-fidelity control centre simulator of the Royal Netherlands Navy. The results show that the method provides good prediction of the task load that will actually appear in the simulator. The model allowed identification of under- and overload situations showing negative effects on operator performance corresponding to controlled experiments in a less realistic task environment. Tools proposed to keep the operator at an optimum task load are (adaptive) task allocation and interface support.

Operators' perception of comfort in two tractor cabs.

PubMed

Ferrari, E; Cavallo, E

2013-01-01

Workspace characteristics affect the perceived comfort level of the operator and uncomfortable working conditions have been found to have a negative impact on productivity and safety. The comfort of the operator is increasingly recognized by manufacturers as a product's added value. Comfort can positively distinguish a product and increase its competitiveness. The concept of comfort is controversial, and a clear operational definition is missing. Nevertheless, it is widely accepted that comfort is a subjective phenomenon that can be evaluated by the final users. In this study, comfort aspects of the tractor workspace interior (i.e., the cab) were investigated. Users with various levels of expertise and two medium-power utility tractors of different brands were used in a 2 x 2 mixed-factorial experimental design. Participants were involved in a dynamic assessment of the cabs, and their opinions about the different workspaces were collected through a questionnaire. Additionally, objective measurements were taken on both tractors, and subjective data were compared with objective data. Results indicate significant differences in terms of the ease of locating and operating the controls (i.e., rear-mounted three-point linkage, hydraulic system, and power take-off), the ease of starting the tractor, the ease exiting the cab, the required level of concentration in executing the tasks, the adequacy of lateral visibility from the driving station, and the level of noise at the operator's position. This article provides guidance for improving the comfort of tractor workspace interiors. Agricultural machinery manufactures would benefit from research results, differentiating themselves from competitors.

Robot dynamics in reduced gravity environment

NASA Technical Reports Server (NTRS)

Workman, Gary L.; Grisham, Tollie; Hinman, Elaine; Coker, Cindy

1990-01-01

Robot dynamics and control will become an important issue for productive platforms in space. Robotic operations will be necessary for both man tended stations and for the efficient performance of routine operations in a manned platform. The current constraints on the use of robotic devices in a microgravity environment appears to be due to safety concerns and an anticipated increase in acceleration levels due to manipulator motion. The robot used for the initial studies was a UMI RTX robot, which was adapted to operate in a materials processing workcell to simulate sample changing in a microgravity environment. The robotic cell was flown several times on the KC-135 aircraft at Ellington Field. The primary objective of the initial flights was to determine operating characteristics of both the robot and the operator in the variable gravity of the KC-135 during parabolic maneuvers. It was demonstrated that the KC-135 aircraft can be used for observing dynamics of robotic manipulators. The difficulties associated with humans performing teleoperation tasks during varying G levels were also observed and can provide insight into some areas in which the use of artificial techniques would provide improved system performance. Additionally a graphic simulation of the workcell was developed on a Silicon Graphics Workstation using the IGRIP simulation language from Deneb Robotics. The simulation is intended to be used for predictive displays of the robot operating on the aircraft. It is also anticipated that this simulation can be useful for off-line programming of tasks in the future.

Dynamic Decision-Making in Multi-Task Environments: Theory and Experimental Results.

DTIC Science & Technology

1981-03-15

The operator’s primary responsibility in this new role is to extract information from his environment, and to integrate it for’ action selection and its...of the human operator from one of a controller to one of a supervisory decision-maker. The operator’s primary responsibility in this new role is to...troller to that of a monitor of multiple tasks, or a supervisor of sev- ~ I eral semi-automated subsystems. The operator’s primary task in these

Occupational health and safety of workers in agriculture and horticulture.

PubMed

Lundqvist, P

2000-01-01

Working in agriculture and horticulture gives considerable job satisfaction. The tasks are often interesting; you can see the result of your own work, watch your crop grow and mature; you have an affinity with nature and can follow the changes in the seasons. However, today it is a dangerous work environment fraught with occupational injuries and diseases due to hazardous situations and to physiological, physical, biological, chemical, psychological, and sociological factors. The ongoing rapid development may, on the other hand, bring about many changes during the next decades with more farmers and growers switching to organic production. Moreover, increased awareness of animal welfare also may lead to improved working conditions. Large-scale operations with fewer family-operated agricultural businesses might mean fewer injuries among children and older farmers. A consequence of large-scale operations may also be better regulation of working conditions. The greater use of automation technology eliminates many harmful working postures and movements when milking cows and carrying out other tasks. Information technology offers people the opportunity to gain more knowledge about their work. Labeling food produced in a worker-friendly work environment may give the consumers a chance to be involved in the process.

The impact of heat stress on operative performance and cognitive function during simulated laparoscopic operative tasks.

PubMed

Berg, Regan J; Inaba, Kenji; Sullivan, Maura; Okoye, Obi; Siboni, Stefano; Minneti, Michael; Teixeira, Pedro G; Demetriades, Demetrios

2015-01-01

Increasing ambient temperature to prevent intraoperative patient hypothermia remains widely advocated despite unconvincing evidence of efficacy. Heat stress is associated with decreased cognitive and psychomotor performance across multiple tasks but remains unexamined in an operative context. We assessed the impact of increased ambient temperature on laparoscopic operative performance and surgeon cognitive stress. Forty-two performance measures were obtained from 21 surgery trainees participating in the counter-balanced, within-subjects study protocol. Operative performance was evaluated with adaptations of the validated, peg-transfer, and intracorporeal knot-tying tasks from the Fundamentals of Laparoscopic Surgery program. Participants trained to proficiency before enrollment. Task performance was measured at two ambient temperatures, 19 and 26°C (66 and 79°F). Participants were randomly counterbalanced to initial hot or cold exposure before crossing over to the alternate environment. Cognitive stress was measured using the validated Surgical Task Load Index (SURG-TLX). No differences in performance of the peg-transfer and intracorporeal knot-tying tasks were seen across ambient conditions. Assessed via use of the six bipolar scales of the SURG-TLX, we found differences in task workload between the hot and cold conditions in the areas of physical demands (hot 10 [3-12], cold 5 [2.5-9], P = .013) and distractions (hot 8 [3.5-15.5], cold 3 [1.5-5.5], P = .001). Participant perception of distraction remained greater in the hot condition on full scoring of the SURG-TLX. Increasing ambient temperature to levels advocated for prevention of intraoperative hypothermia does not greatly decrease technical performance in short operative tasks. Surgeons, however, do report increased perceptions of distraction and physical demand. The impact of these findings on performance and outcomes during longer operative procedures remains unclear. Copyright © 2015 Elsevier Inc. All rights reserved.

Operational Processing of Ground Validation Data for the Tropical Rainfall Measuring Mission

NASA Technical Reports Server (NTRS)

Kulie, Mark S.; Robinson, Mike; Marks, David A.; Ferrier, Brad S.; Rosenfeld, Danny; Wolff, David B.

1999-01-01

The Tropical Rainfall Measuring Mission (TRMM) satellite was successfully launched in November 1997. A primary goal of TRMM is to sample tropical rainfall using the first active spaceborne precipitation radar. To validate TRMM satellite observations, a comprehensive Ground Validation (GV) Program has been implemented for this mission. A key component of GV is the analysis and quality control of meteorological ground-based radar data from four primary sites: Melbourne, FL; Houston, TX; Darwin, Australia; and Kwajalein Atoll, RMI. As part of the TRMM GV effort, the Joint Center for Earth Systems Technology (JCET) at the University of Maryland, Baltimore County, has been tasked with developing and implementing an operational system to quality control (QC), archive, and provide data for subsequent rainfall product generation from the four primary GV sites. This paper provides an overview of the JCET operational environment. A description of the QC algorithm and performance, in addition to the data flow procedure between JCET and the TRNM science and Data Information System (TSDIS), are presented. The impact of quality-controlled data on higher level rainfall and reflectivity products will also be addressed, Finally, a brief description of JCET's expanded role into producing reference rainfall products will be discussed.

Deconstructing and Reconstructing Cognitive Performance in Sleep Deprivation

PubMed Central

Jackson, Melinda L.; Gunzelmann, Glenn; Whitney, Paul; Hinson, John M.; Belenky, Gregory; Rabat, Arnaud; Van Dongen, Hans P. A.

2012-01-01

Summary Mitigation of cognitive impairment due to sleep deprivation in operational settings is critical for safety and productivity. Achievements in this area are hampered by limited knowledge about the effects of sleep loss on actual job tasks. Sleep deprivation has different effects on different cognitive performance tasks, but the mechanisms behind this task-specificity are poorly understood. In this context it is important to recognize that cognitive performance is not a unitary process, but involves a number of component processes. There is emerging evidence that these component processes are differentially affected by sleep loss. Experiments have been conducted to decompose sleep-deprived performance into underlying cognitive processes using cognitive-behavioral, neuroimaging and cognitive modeling techniques. Furthermore, computational modeling in cognitive architectures has been employed to simulate sleep-deprived cognitive performance on the basis of the constituent cognitive processes. These efforts are beginning to enable quantitative prediction of the effects of sleep deprivation across different task contexts. This paper reviews a rapidly evolving area of research, and outlines a theoretical framework in which the effects of sleep loss on cognition may be understood from the deficits in the underlying neurobiology to the applied consequences in real-world job tasks. PMID:22884948

Deconstructing and reconstructing cognitive performance in sleep deprivation.

PubMed

Jackson, Melinda L; Gunzelmann, Glenn; Whitney, Paul; Hinson, John M; Belenky, Gregory; Rabat, Arnaud; Van Dongen, Hans P A

2013-06-01

Mitigation of cognitive impairment due to sleep deprivation in operational settings is critical for safety and productivity. Achievements in this area are hampered by limited knowledge about the effects of sleep loss on actual job tasks. Sleep deprivation has different effects on different cognitive performance tasks, but the mechanisms behind this task-specificity are poorly understood. In this context it is important to recognize that cognitive performance is not a unitary process, but involves a number of component processes. There is emerging evidence that these component processes are differentially affected by sleep loss. Experiments have been conducted to decompose sleep-deprived performance into underlying cognitive processes using cognitive-behavioral, neuroimaging and cognitive modeling techniques. Furthermore, computational modeling in cognitive architectures has been employed to simulate sleep-deprived cognitive performance on the basis of the constituent cognitive processes. These efforts are beginning to enable quantitative prediction of the effects of sleep deprivation across different task contexts. This paper reviews a rapidly evolving area of research, and outlines a theoretical framework in which the effects of sleep loss on cognition may be understood from the deficits in the underlying neurobiology to the applied consequences in real-world job tasks. Copyright © 2012 Elsevier Ltd. All rights reserved.

Maintaining a Distributed File System by Collection and Analysis of Metrics

NASA Technical Reports Server (NTRS)

Bromberg, Daniel

1997-01-01

AFS(originally, Andrew File System) is a widely-deployed distributed file system product used by companies, universities, and laboratories world-wide. However, it is not trivial to operate: runing an AFS cell is a formidable task. It requires a team of dedicated and experienced system administratores who must manage a user base numbring in the thousands, rather than the smaller range of 10 to 500 faced by the typical system administrator.

Integrated Design of a Telerobotic Workstation

NASA Technical Reports Server (NTRS)

Rochlis, Jennifer L.; Clarke, John-Paul

2001-01-01

The experiments described in this paper are part of a larger joint MIT/NASA research effort that focuses on the development of a methodology for designing and evaluating integrated interfaces for highly dexterous and multi-functional telerobots. Specifically, a telerobotic workstation is being designed for an Extravehicular Activity (EVA) anthropomorphic space station telerobot. Previous researchers have designed telerobotic workstations based upon performance of discrete subsets of tasks (for example, peg-in-hole, tracking, etc.) without regard for transitions that operators go through between tasks performed sequentially in the context of larger integrated tasks. The exploratory research experiments presented here took an integrated approach and assessed how subjects operating a full-immersion telerobot perform during the transitions between sub-tasks of two common EVA tasks. Preliminary results show that up to 30% of total task time is spent gaining and maintaining Situation Awareness (SA) of their task space and environment during transitions. Although task performance improves over the two trial days, the percentage of time spent on SA remains the same. This method identifies areas where workstation displays and feedback mechanisms are most needed to increase operator performance and decrease operator workload - areas that previous research methods have not been able to address.

Scheduling algorithms for automatic control systems for technological processes

NASA Astrophysics Data System (ADS)

Chernigovskiy, A. S.; Tsarev, R. Yu; Kapulin, D. V.

2017-01-01

Wide use of automatic process control systems and the usage of high-performance systems containing a number of computers (processors) give opportunities for creation of high-quality and fast production that increases competitiveness of an enterprise. Exact and fast calculations, control computation, and processing of the big data arrays - all of this requires the high level of productivity and, at the same time, minimum time of data handling and result receiving. In order to reach the best time, it is necessary not only to use computing resources optimally, but also to design and develop the software so that time gain will be maximal. For this purpose task (jobs or operations), scheduling techniques for the multi-machine/multiprocessor systems are applied. Some of basic task scheduling methods for the multi-machine process control systems are considered in this paper, their advantages and disadvantages come to light, and also some usage considerations, in case of the software for automatic process control systems developing, are made.

Development of an inpatient operational pharmacy productivity model.

PubMed

Naseman, Ryan W; Lopez, Ben R; Forrey, Ryan A; Weber, Robert J; Kipp, Kris M

2015-02-01

An innovative model for measuring the operational productivity of medication order management in inpatient settings is described. Order verification within a computerized prescriber order-entry system was chosen as the pharmacy workload driver. To account for inherent variability in the tasks involved in processing different types of orders, pharmaceutical products were grouped by class, and each class was assigned a time standard, or "medication complexity weight" reflecting the intensity of pharmacist and technician activities (verification of drug indication, verification of appropriate dosing, adverse-event prevention and monitoring, medication preparation, product checking, product delivery, returns processing, nurse/provider education, and problem-order resolution). The resulting "weighted verifications" (WV) model allows productivity monitoring by job function (pharmacist versus technician) to guide hiring and staffing decisions. A 9-month historical sample of verified medication orders was analyzed using the WV model, and the calculations were compared with values derived from two established models—one based on the Case Mix Index (CMI) and the other based on the proprietary Pharmacy Intensity Score (PIS). Evaluation of Pearson correlation coefficients indicated that values calculated using the WV model were highly correlated with those derived from the CMI-and PIS-based models (r = 0.845 and 0.886, respectively). Relative to the comparator models, the WV model offered the advantage of less period-to-period variability. The WV model yielded productivity data that correlated closely with values calculated using two validated workload management models. The model may be used as an alternative measure of pharmacy operational productivity. Copyright © 2015 by the American Society of Health-System Pharmacists, Inc. All rights reserved.

Automation trust and attention allocation in multitasking workspace.

PubMed

Karpinsky, Nicole D; Chancey, Eric T; Palmer, Dakota B; Yamani, Yusuke

2018-07-01

Previous research suggests that operators with high workload can distrust and then poorly monitor automation, which has been generally inferred from automation dependence behaviors. To test automation monitoring more directly, the current study measured operators' visual attention allocation, workload, and trust toward imperfect automation in a dynamic multitasking environment. Participants concurrently performed a manual tracking task with two levels of difficulty and a system monitoring task assisted by an unreliable signaling system. Eye movement data indicate that operators allocate less visual attention to monitor automation when the tracking task is more difficult. Participants reported reduced levels of trust toward the signaling system when the tracking task demanded more focused visual attention. Analyses revealed that trust mediated the relationship between the load of the tracking task and attention allocation in Experiment 1, an effect that was not replicated in Experiment 2. Results imply a complex process underlying task load, visual attention allocation, and automation trust during multitasking. Automation designers should consider operators' task load in multitasking workspaces to avoid reduced automation monitoring and distrust toward imperfect signaling systems. Copyright © 2018. Published by Elsevier Ltd.

Evaluation of telerobotic systems using an instrumented task board

NASA Technical Reports Server (NTRS)

Carroll, John D.; Gierow, Paul A.; Bryan, Thomas C.

1991-01-01

An instrumented task board was developed at NASA Marshall Space Flight Center (MSFC). An overview of the task board design, and current development status is presented. The task board was originally developed to evaluate operator performance using the Protoflight Manipulator Arm (PFMA) at MSFC. The task board evaluates tasks for Orbital Replacement Unit (ORU), fluid connect and transfers, electrical connect/disconnect, bolt running, and other basic tasks. The instrumented task board measures the 3-D forces and torques placed on the board, determines the robot arm's 3-D position relative to the task board using IR optics, and provides the information in real-time. The PFMA joint input signals can also be measured from a breakout box to evaluate the sensitivity or response of the arm operation to control commands. The data processing system provides the capability for post processing of time-history graphics and plots of the PFMA positions, the operator's actions, and the PFMA servo reactions in addition to real-time force/torque data presentation. The instrumented task board's most promising use is developing benchmarks for NASA centers for comparison and evaluation of telerobotic performance.

Lageos assembly operation plan

NASA Technical Reports Server (NTRS)

Brueger, J.

1975-01-01

Guidelines and constraints procedures for LAGEOS assembly, operation, and design performance are given. Special attention was given to thermal, optical, and dynamic analysis and testing. The operation procedures illustrate the interrelation and sequence of tasks in a flow diagram. The diagram also includes quality assurance functions for verification of operation tasks.

Biocybernetic system evaluates indices of operator engagement in automated task

NASA Technical Reports Server (NTRS)

Pope, A. T.; Bogart, E. H.; Bartolome, D. S.

1995-01-01

A biocybernetic system has been developed as a method to evaluate automated flight deck concepts for compatibility with human capabilities. A biocybernetic loop is formed by adjusting the mode of operation of a task set (e.g., manual/automated mix) based on electroencephalographic (EEG) signals reflecting an operator's engagement in the task set. A critical issue for the loop operation is the selection of features of the EEG to provide an index of engagement upon which to base decisions to adjust task mode. Subjects were run in the closed-loop feedback configuration under four candidate and three experimental control definitions of an engagement index. The temporal patterning of system mode switching was observed for both positive and negative feedback of the index. The indices were judged on the basis of their relative strength in exhibiting expected feedback control system phenomena (stable operation under negative feedback and unstable operation under positive feedback). Of the candidate indices evaluated in this study, an index constructed according to the formula, beta power/(alpha power + theta power), reflected task engagement best.

The Transportable Applications Environment - An interactive design-to-production development system

NASA Technical Reports Server (NTRS)

Perkins, Dorothy C.; Howell, David R.; Szczur, Martha R.

1988-01-01

An account is given of the design philosophy and architecture of the Transportable Applications Environment (TAE), an executive program binding a system of applications programs into a single, easily operable whole. TAE simplifies the job of a system developer by furnishing a stable framework for system-building; it also integrates system activities, and cooperates with the host operating system in order to perform such functions as task-scheduling and I/O. The initial TAE human/computer interface supported command and menu interfaces, data displays, parameter-prompting, error-reporting, and online help. Recent extensions support graphics workstations with a window-based, modeless user interface.

The Lunar Mapping and Modeling Project

NASA Technical Reports Server (NTRS)

Noble, Sarah K.; French, R. A.; Nall, M. E.; Muery, K. G.

2009-01-01

The Lunar Mapping and Modeling Project (LMMP) has been created to manage the development of a suite of lunar mapping and modeling products that support the Constellation Program (CxP) and other lunar exploration activities, including the planning, design, development, test and operations associated with lunar sortie missions, crewed and robotic operations on the surface, and the establishment of a lunar outpost. The information provided through LMMP will assist CxP in: planning tasks in the areas of landing site evaluation and selection, design and placement of landers and other stationary assets, design of rovers and other mobile assets, developing terrain-relative navigation (TRN) capabilities, and assessment and planning of science traverses.

Honing process optimization algorithms

NASA Astrophysics Data System (ADS)

Kadyrov, Ramil R.; Charikov, Pavel N.; Pryanichnikova, Valeria V.

2018-03-01

This article considers the relevance of honing processes for creating high-quality mechanical engineering products. The features of the honing process are revealed and such important concepts as the task for optimization of honing operations, the optimal structure of the honing working cycles, stepped and stepless honing cycles, simulation of processing and its purpose are emphasized. It is noted that the reliability of the mathematical model determines the quality parameters of the honing process control. An algorithm for continuous control of the honing process is proposed. The process model reliably describes the machining of a workpiece in a sufficiently wide area and can be used to operate the CNC machine CC743.

A Study on the Validity of a Task Complexity Measure for Emergency Operating Procedures of Nuclear Power Plants—Comparing With a Subjective Workload

NASA Astrophysics Data System (ADS)

Park, J.; Jung, W.

2006-10-01

In this study, the appropriateness of the task complexity (TACOM) measure that can quantify the complexity of emergency tasks was investigated by comparing subjective workload scores with the associated TACOM scores. To this end, based on the NASA-TLX (task load index) technique, 18 operators were asked to subjectively estimate perceived workload for 23 emergency tasks that were specified in the emergency operating procedures of the reference nuclear power plants. As the result of comparisons, it was observed that subjective workload scores increase in proportion to the increase of TACOM scores. Therefore, it is expect that the TACOM measure can be used as a serviceable method to quantify the complexity of emergency tasks

A functional approach for research on cognitive control: Analysing cognitive control tasks and their effects in terms of operant conditioning.

PubMed

Liefooghe, Baptist; De Houwer, Jan

2016-02-01

Cognitive control is an important mental ability that is examined using a multitude of cognitive control tasks and effects. The present paper presents the first steps in the elaboration of a functional approach, which aims to uncover the communalities and differences between different cognitive control tasks and their effects. Based on the idea that responses in cognitive control tasks qualify as operant behaviour, we propose to reinterpret cognitive control tasks in terms of operant contingencies and cognitive control effects as instances of moderated stimulus control. We illustrate how our approach can be used to uncover communalities between topographically different cognitive control tasks and can lead to novel questions about the processes underlying cognitive control. © 2015 International Union of Psychological Science.

An integrated tool to support engineers for WMSDs risk assessment during the assembly line balancing.

PubMed

Di Benedetto, Raffaele; Fanti, Michele

2012-01-01

This paper wants to present an integrated approach to Line Balancing and Risk Assessment and a Software Tool named ErgoAnalysis that makes it easy to control the whole production process and produces a Risk Index for the actual work tasks in an Assembly Line. Assembly Line Balancing, or simply Line Balancing, is the problem of assigning operations to workstations along an assembly line, in such a way that the assignment be optimal in some sense. Assembly lines are characterized by production constraints and restrictions due to several aspects such as the nature of the product and the flow of orders. To be able to respond effectively to the needs of production, companies need to frequently change the workload and production models. Each manufacturing process might be quite different from another. To optimize very specific operations, assembly line balancing might utilize a number of methods and the Engineer must consider ergonomic constraints, in order to reduce the risk of WMDSs. Risk Assessment may result very expensive because the Engineer must evaluate it at every change. ErgoAnalysis can reduce cost and improve effectiveness in Risk Assessment during the Line Balancing.

Simulation-optimization model for production planning in the blood supply chain.

PubMed

Osorio, Andres F; Brailsford, Sally C; Smith, Honora K; Forero-Matiz, Sonia P; Camacho-Rodríguez, Bernardo A

2017-12-01

Production planning in the blood supply chain is a challenging task. Many complex factors such as uncertain supply and demand, blood group proportions, shelf life constraints and different collection and production methods have to be taken into account, and thus advanced methodologies are required for decision making. This paper presents an integrated simulation-optimization model to support both strategic and operational decisions in production planning. Discrete-event simulation is used to represent the flows through the supply chain, incorporating collection, production, storing and distribution. On the other hand, an integer linear optimization model running over a rolling planning horizon is used to support daily decisions, such as the required number of donors, collection methods and production planning. This approach is evaluated using real data from a blood center in Colombia. The results show that, using the proposed model, key indicators such as shortages, outdated units, donors required and cost are improved.

Modeling strategic behavior in human-automation interaction - Why an 'aid' can (and should) go unused

NASA Technical Reports Server (NTRS)

Kirlik, Alex

1993-01-01

Task-offload aids (e.g., an autopilot, an 'intelligent' assistant) can be selectively engaged by the human operator to dynamically delegate tasks to automation. Introducing such aids eliminates some task demands but creates new ones associated with programming, engaging, and disengaging the aiding device via an interface. The burdens associated with managing automation can sometimes outweigh the potential benefits of automation to improved system performance. Aid design parameters and features of the overall multitask context combine to determine whether or not a task-offload aid will effectively support the operator. A modeling and sensitivity analysis approach is presented that identifies effective strategies for human-automation interaction as a function of three task-context parameters and three aid design parameters. The analysis and modeling approaches provide resources for predicting how a well-adapted operator will use a given task-offload aid, and for specifying aid design features that ensure that automation will provide effective operator support in a multitask environment.

Research, development and demonstration of nickel-zinc batteries for electric vehicle propulsion

NASA Astrophysics Data System (ADS)

1980-06-01

The feasibility of the nickel zinc battery for electric vehicle propulsion is discussed. The program is divided into seven distinct but highly interactive tasks collectively aimed at the development and commercialization of nickel zinc technology. These basic technical tasks are separator development, electrode development, product design and analysis, cell/module battery testing, process development, pilot manufacturing, and thermal manufacturing, and thermal management. Significant progress has been made in the understanding of separator failure mechanisms, and a generic category of materials has been specified for the 300+ deep discharge applications. Shape change has been reduced significantly. Progress in the area of thermal management was significant, with the development of a model that accurately represents heat generation and rejection rates during battery operation.

Control of intelligent robots in space

NASA Technical Reports Server (NTRS)

Freund, E.; Buehler, CH.

1989-01-01

In view of space activities like International Space Station, Man-Tended-Free-Flyer (MTFF) and free flying platforms, the development of intelligent robotic systems is gaining increasing importance. The range of applications that have to be performed by robotic systems in space includes e.g., the execution of experiments in space laboratories, the service and maintenance of satellites and flying platforms, the support of automatic production processes or the assembly of large network structures. Some of these tasks will require the development of bi-armed or of multiple robotic systems including functional redundancy. For the development of robotic systems which are able to perform this variety of tasks a hierarchically structured modular concept of automation is required. This concept is characterized by high flexibility as well as by automatic specialization to the particular sequence of tasks that have to be performed. On the other hand it has to be designed such that the human operator can influence or guide the system on different levels of control supervision, and decision. This leads to requirements for the hardware and software concept which permit a range of application of the robotic systems from telemanipulation to autonomous operation. The realization of this goal requires strong efforts in the development of new methods, software and hardware concepts, and the integration into an automation concept.

POPCORN: a Supervisory Control Simulation for Workload and Performance Research

NASA Technical Reports Server (NTRS)

Hart, S. G.; Battiste, V.; Lester, P. T.

1984-01-01

A multi-task simulation of a semi-automatic supervisory control system was developed to provide an environment in which training, operator strategy development, failure detection and resolution, levels of automation, and operator workload can be investigated. The goal was to develop a well-defined, but realistically complex, task that would lend itself to model-based analysis. The name of the task (POPCORN) reflects the visual display that depicts different task elements milling around waiting to be released and pop out to be performed. The operator's task was to complete each of 100 task elements that ere represented by different symbols, by selecting a target task and entering the desired a command. The simulated automatic system then completed the selected function automatically. Highly significant differences in performance, strategy, and rated workload were found as a function of all experimental manipulations (except reward/penalty).

Multi-attribute subjective evaluations of manual tracking tasks vs. objective performance of the human operator

NASA Technical Reports Server (NTRS)

Siapkaras, A.

1977-01-01

A computational method to deal with the multidimensional nature of tracking and/or monitoring tasks is developed. Operator centered variables, including the operator's perception of the task, are considered. Matrix ratings are defined based on multidimensional scaling techniques and multivariate analysis. The method consists of two distinct steps: (1) to determine the mathematical space of subjective judgements of a certain individual (or group of evaluators) for a given set of tasks and experimental conditionings; and (2) to relate this space with respect to both the task variables and the objective performance criteria used. Results for a variety of second-order trackings with smoothed noise-driven inputs indicate that: (1) many of the internally perceived task variables form a nonorthogonal set; and (2) the structure of the subjective space varies among groups of individuals according to the degree of familiarity they have with such tasks.

Internet Based Remote Operations

NASA Technical Reports Server (NTRS)

Chamberlain, James

1999-01-01

This is the Final Report for the Internet Based Remote Operations Contract, has performed payload operations research support tasks March 1999 through September 1999. These tasks support the GSD goal of developing a secure, inexpensive data, voice, and video mission communications capability between remote payload investigators and the NASA payload operations team in the International Space Station (ISS) era. AZTek has provided feedback from the NASA payload community by utilizing its extensive payload development and operations experience to test and evaluate remote payload operations systems. AZTek has focused on use of the "public Internet" and inexpensive, Commercial-off-the-shelf (COTS) Internet-based tools that would most benefit "small" (e.g., $2 Million or less) payloads and small developers without permanent remote operations facilities. Such projects have limited budgets to support installation and development of high-speed dedicated communications links and high-end, custom ground support equipment and software. The primary conclusions of the study are as follows: (1) The trend of using Internet technology for "live" collaborative applications such as telescience will continue. The GSD-developed data and voice capabilities continued to work well over the "public" Internet during this period. 2. Transmitting multiple voice streams from a voice-conferencing server to a client PC to be mixed and played on the PC is feasible. 3. There are two classes of voice vendors in the market: - Large traditional phone equipment vendors pursuing integration of PSTN with Internet, and Small Internet startups.The key to selecting a vendor will be to find a company sufficiently large and established to provide a base voice-conferencing software product line for the next several years.

Spitzer Space Telescope Sequencing Operations Software, Strategies, and Lessons Learned

NASA Technical Reports Server (NTRS)

Bliss, David A.

2006-01-01

The Space Infrared Telescope Facility (SIRTF) was launched in August, 2003, and renamed to the Spitzer Space Telescope in 2004. Two years of observing the universe in the wavelength range from 3 to 180 microns has yielded enormous scientific discoveries. Since this magnificent observatory has a limited lifetime, maximizing science viewing efficiency (ie, maximizing time spent executing activities directly related to science observations) was the key operational objective. The strategy employed for maximizing science viewing efficiency was to optimize spacecraft flexibility, adaptability, and use of observation time. The selected approach involved implementation of a multi-engine sequencing architecture coupled with nondeterministic spacecraft and science execution times. This approach, though effective, added much complexity to uplink operations and sequence development. The Jet Propulsion Laboratory (JPL) manages Spitzer s operations. As part of the uplink process, Spitzer s Mission Sequence Team (MST) was tasked with processing observatory inputs from the Spitzer Science Center (SSC) into efficiently integrated, constraint-checked, and modeled review and command products which accommodated the complexity of non-deterministic spacecraft and science event executions without increasing operations costs. The MST developed processes, scripts, and participated in the adaptation of multi-mission core software to enable rapid processing of complex sequences. The MST was also tasked with developing a Downlink Keyword File (DKF) which could instruct Deep Space Network (DSN) stations on how and when to configure themselves to receive Spitzer science data. As MST and uplink operations developed, important lessons were learned that should be applied to future missions, especially those missions which employ command-intensive operations via a multi-engine sequence architecture.

Software Product Lines: Report of the 2010 US Army Software Product Line Workshop

DTIC Science & Technology

2010-06-01

requirements and statement of work ( SOW ) tasks can be in- cluded in the request for proposal (RFP) and the contract. 2.2.1 Basic Product Line Acquisition... SOW tasks in Figure 1. Two additional tasks (at the third tier level) ac- count for sustaining the production capability over the life cycle and...Acquisition Strategy RFP and SOW Initial Product Line Scope Product Line Business Case Capability Description Document Teaming Product Line

The Effects of Multimedia Task-Based Language Teaching on EFL Learners' Oral L2 Production

ERIC Educational Resources Information Center

BavaHarji, Madhubala; Gheitanchian, Mehrnaz; Letchumanan, Krishnaveni

2014-01-01

This study examined the effects of tasks, with varying levels of complexity, i.e. simple, + complex and ++ complex tasks on EFL learners' oral production in a multimedia task-based language teaching environment. 57 EFL adult learners carried out a total of 12 tasks, in sets of four tasks within three different themes and different levels of…

Contingency and similarity in response selection.

PubMed

Prinz, Wolfgang

2018-05-09

This paper explores issues of task representation in choice reaction time tasks. How is it possible, and what does it take, to represent such a task in a way that enables a performer to do the task in line with the prescriptions entailed in the instructions? First, a framework for task representation is outlined which combines the implementation of task sets and their use for performance with different kinds of representational operations (pertaining to feature compounds for event codes and code assemblies for task sets, respectively). Then, in a second step, the framework is itself embedded in the bigger picture of the classical debate on the roles of contingency and similarity for the formation of associations. The final conclusion is that both principles are needed and that the operation of similarity at the level of task sets requires and presupposes the operation of contingency at the level of event codes. Copyright © 2018 The Author. Published by Elsevier Inc. All rights reserved.

Using task analysis to understand the Data System Operations Team

NASA Technical Reports Server (NTRS)

Holder, Barbara E.

1994-01-01

The Data Systems Operations Team (DSOT) currently monitors the Multimission Ground Data System (MGDS) at JPL. The MGDS currently supports five spacecraft and within the next five years, it will support ten spacecraft simultaneously. The ground processing element of the MGDS consists of a distributed UNIX-based system of over 40 nodes and 100 processes. The MGDS system provides operators with little or no information about the system's end-to-end processing status or end-to-end configuration. The lack of system visibility has become a critical issue in the daily operation of the MGDS. A task analysis was conducted to determine what kinds of tools were needed to provide DSOT with useful status information and to prioritize the tool development. The analysis provided the formality and structure needed to get the right information exchange between development and operations. How even a small task analysis can improve developer-operator communications is described, and the challenges associated with conducting a task analysis in a real-time mission operations environment are examined.

Operational Monitoring of GOME-2 and IASI Level 1 Product Processing at EUMETSAT

NASA Astrophysics Data System (ADS)

Livschitz, Yakov; Munro, Rosemary; Lang, Rüdiger; Fiedler, Lars; Dyer, Richard; Eisinger, Michael

2010-05-01

The growing complexity of operational level 1 radiance products from Low Earth Orbiting (LEO) platforms like EUMETSATs Metop series makes near-real-time monitoring of product quality a challenging task. The main challenge is to provide a monitoring system which is flexible and robust enough to identify and to react to anomalies which may be previously unknown to the system, as well as to provide all means and parameters necessary in order to support efficient ad-hoc analysis of the incident. The operational monitoring system developed at EUMETSAT for monitoring of GOME-2 and IASI level 1 data allows to perform near-real-time monitoring of operational products and instrument's health in a robust and flexible fashion. For effective information management, the system is based on a relational database (Oracle). An Extract, Transform, Load (ETL) process transforms products in EUMETSAT Polar System (EPS) format into relational data structures. The identification of commonalities between products and instruments allows for a database structure design in such a way that different data can be analyzed using the same business intelligence functionality. An interactive analysis software implementing modern data mining techniques is also provided for a detailed look into the data. The system is effectively used for day-to-day monitoring, long-term reporting, instrument's degradation analysis as well as for ad-hoc queries in case of an unexpected instrument or processing behaviour. Having data from different sources on a single instrument and even from different instruments, platforms or numerical weather prediction within the same database allows effective cross-comparison and looking for correlated parameters. Automatic alarms raised by checking for deviation of certain parameters, for data losses and other events significantly reduce time, necessary to monitor the processing on a day-to-day basis.

Operational Monitoring of GOME-2 and IASI Level 1 Product Processing at EUMETSAT

NASA Astrophysics Data System (ADS)

Livschitz, Y.; Munro, R.; Lang, R.; Fiedler, L.; Dyer, R.; Eisinger, M.

2009-12-01

The growing complexity of operational level 1 radiance products from Low Earth Orbiting (LEO) platforms like EUMETSATs Metop series makes near-real-time monitoring of product quality a challenging task. The main challenge is to provide a monitoring system which is flexible and robust enough to identify and to react to anomalies which may be previously unknown to the system, as well as to provide all means and parameters necessary in order to support efficient ad-hoc analysis of the incident. The operational monitoring system developed at EUMETSAT for monitoring of GOME-2 and IASI level 1 data allows to perform near-real-time monitoring of operational products and instrument’s health in a robust and flexible fashion. For effective information management, the system is based on a relational database (Oracle). An Extract, Transform, Load (ETL) process transforms products in EUMETSAT Polar System (EPS) format into relational data structures. The identification of commonalities between products and instruments allows for a database structure design in such a way that different data can be analyzed using the same business intelligence functionality. An interactive analysis software implementing modern data mining techniques is also provided for a detailed look into the data. The system is effectively used for day-to-day monitoring, long-term reporting, instrument’s degradation analysis as well as for ad-hoc queries in case of an unexpected instrument or processing behaviour. Having data from different sources on a single instrument and even from different instruments, platforms or numerical weather prediction within the same database allows effective cross-comparison and looking for correlated parameters. Automatic alarms raised by checking for deviation of certain parameters, for data losses and other events significantly reduce time, necessary to monitor the processing on a day-to-day basis.

Psychomotor performance measured in a virtual environment correlates with technical skills in the operating room.

PubMed

Kundhal, Pavi S; Grantcharov, Teodor P

2009-03-01

This study was conducted to validate the role of virtual reality computer simulation as an objective method for assessing laparoscopic technical skills. The authors aimed to investigate whether performance in the operating room, assessed using a modified Objective Structured Assessment of Technical Skill (OSATS), correlated with the performance parameters registered by a virtual reality laparoscopic trainer (LapSim). The study enrolled 10 surgical residents (3 females) with a median of 5.5 years (range, 2-6 years) since graduation who had similar limited experience in laparoscopic surgery (median, 5; range, 1-16 laparoscopic cholecystectomies). All the participants performed three repetitions of seven basic skills tasks on the LapSim laparoscopic trainer and one laparoscopic cholecystectomy in the operating room. The operating room procedure was video recorded and blindly assessed by two independent observers using a modified OSATS rating scale. Assessment in the operating room was based on three parameters: time used, error score, and economy of motion score. During the tasks on the LapSim, time, error (tissue damage and millimeters of tissue damage [tasks 2-6], error score [incomplete target areas, badly placed clips, and dropped clips [task 7]), and economy of movement parameters (path length and angular path) were registered. The correlation between time, economy, and error parameters during the simulated tasks and the operating room procedure was statistically assessed using Spearman's test. Significant correlations were demonstrated between the time used to complete the operating room procedure and time used for task 7 (r (s) = 0.74; p = 0.015). The error score demonstrated during the laparoscopic cholecystectomy correlated well with the tissue damage in three of the seven tasks (p < 0.05), the millimeters of tissue damage during two of the tasks, and the error score in task 7 (r (s) = 0.67; p = 0.034). Furthermore, statistically significant correlations were observed between the economy of motion score from the operative procedure and LapSim's economy parameters (path length and angular path in six of the tasks) (p < 0.05). The current study demonstrated significant correlations between operative performance in the operating room (assessed using a well-validated rating scale) and psychomotor performance in virtual environment assessed by a computer simulator. This provides strong evidence for the validity of the simulator system as an objective tool for assessing laparoscopic skills. Virtual reality simulation can be used in practice to assess technical skills relevant for minimally invasive surgery.

Low-cost solar array project task 1: Silicon material. Gaseous melt replenishment system

NASA Technical Reports Server (NTRS)

Jewett, D. N.; Bates, H. E.; Hill, D. M.

1980-01-01

The operation of a silicon production technique was demonstrated. The essentials of the method comprise chemical vapor deposition of silicon, by hydrogen reduction of chlorosilanes, on the inside of a quartz reaction vessel having large internal surface area. The system was designed to allow successive deposition-melting cycles, with silicon removal being accomplished by discharging the molten silicon. The liquid product would be suitable for transfer to a crystal growth process, casting into solid form, or production of shots. A scaled-down prototype reactor demonstrated single pass conversion efficiency of 20 percent and deposition rates and energy consumption better than conventional Siemens reactors, via deposition rates of 365 microns/hr. and electrical consumption of 35 Kwhr/kg of silicon produced.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Niccoli, G.

The antiperiodic transfer matrices associated to higher spin representations of the rational 6-vertex Yang-Baxter algebra are analyzed by generalizing the approach introduced recently in the framework of Sklyanin's quantum separation of variables (SOV) for cyclic representations, spin-1/2 highest weight representations, and also for spin-1/2 representations of the 6-vertex reflection algebra. Such SOV approach allow us to derive exactly results which represent complicate tasks for more traditional methods based on Bethe ansatz and Baxter Q-operator. In particular, we both prove the completeness of the SOV characterization of the transfer matrix spectrum and its simplicity. Then, the derived characterization of local operatorsmore » by Sklyanin's quantum separate variables and the expression of the scalar products of separate states by determinant formulae allow us to compute the form factors of the local spin operators by one determinant formulae similar to those of the scalar products.« less

Renormalizing Entanglement Distillation.

PubMed

Waeldchen, Stephan; Gertis, Janina; Campbell, Earl T; Eisert, Jens

2016-01-15

Entanglement distillation refers to the task of transforming a collection of weakly entangled pairs into fewer highly entangled ones. It is a core ingredient in quantum repeater protocols, which are needed to transmit entanglement over arbitrary distances in order to realize quantum key distribution schemes. Usually, it is assumed that the initial entangled pairs are identically and independently distributed and are uncorrelated with each other, an assumption that might not be reasonable at all in any entanglement generation process involving memory channels. Here, we introduce a framework that captures entanglement distillation in the presence of natural correlations arising from memory channels. Conceptually, we bring together ideas from condensed-matter physics-ideas from renormalization and matrix-product states and operators-with those of local entanglement manipulation, Markov chain mixing, and quantum error correction. We identify meaningful parameter regions for which we prove convergence to maximally entangled states, arising as the fixed points of a matrix-product operator renormalization flow.

Versatile and declarative dynamic programming using pair algebras.

PubMed

Steffen, Peter; Giegerich, Robert

2005-09-12

Dynamic programming is a widely used programming technique in bioinformatics. In sharp contrast to the simplicity of textbook examples, implementing a dynamic programming algorithm for a novel and non-trivial application is a tedious and error prone task. The algebraic dynamic programming approach seeks to alleviate this situation by clearly separating the dynamic programming recurrences and scoring schemes. Based on this programming style, we introduce a generic product operation of scoring schemes. This leads to a remarkable variety of applications, allowing us to achieve optimizations under multiple objective functions, alternative solutions and backtracing, holistic search space analysis, ambiguity checking, and more, without additional programming effort. We demonstrate the method on several applications for RNA secondary structure prediction. The product operation as introduced here adds a significant amount of flexibility to dynamic programming. It provides a versatile testbed for the development of new algorithmic ideas, which can immediately be put to practice.

FMEA and consideration of real work situations for safer design of production systems.

PubMed

Lux, Aurélien; Mawo De Bikond, Johann; Etienne, Alain; Quillerou-Grivot, Edwige

2016-12-01

Production equipment designers must ensure the health and safety of future users; in this regard, they augment requirements for standardizing and controlling operator work. This contrasts with the ergonomic view of the activity, which recommends leaving operators leeway (margins for manoeuvre) in performing their task, while safeguarding their health. Following a brief analysis of design practices in the car industry, we detail how the Failure Modes and Effects Analysis (FMEA) approach is implemented in this sector. We then suggest an adaptation that enables designers to consider real work situations. This new protocol, namely, work situation FMEA, allows experience feedback to be used to defend the health standpoint during designer project reviews, which usually only address quality and performance issues. We subsequently illustrate the advantage of this approach using two examples of work situations at car parts manufacturers: the first from the literature and the second from an in-company industrial project.

Extensions to the Parallel Real-Time Artificial Intelligence System (PRAIS) for fault-tolerant heterogeneous cycle-stealing reasoning

NASA Technical Reports Server (NTRS)

Goldstein, David

1991-01-01

Extensions to an architecture for real-time, distributed (parallel) knowledge-based systems called the Parallel Real-time Artificial Intelligence System (PRAIS) are discussed. PRAIS strives for transparently parallelizing production (rule-based) systems, even under real-time constraints. PRAIS accomplished these goals (presented at the first annual C Language Integrated Production System (CLIPS) conference) by incorporating a dynamic task scheduler, operating system extensions for fact handling, and message-passing among multiple copies of CLIPS executing on a virtual blackboard. This distributed knowledge-based system tool uses the portability of CLIPS and common message-passing protocols to operate over a heterogeneous network of processors. Results using the original PRAIS architecture over a network of Sun 3's, Sun 4's and VAX's are presented. Mechanisms using the producer-consumer model to extend the architecture for fault-tolerance and distributed truth maintenance initiation are also discussed.

Application of auditory signals to the operation of an agricultural vehicle: results of pilot testing.

PubMed

Karimi, D; Mondor, T A; Mann, D D

2008-01-01

The operation of agricultural vehicles is a multitask activity that requires proper distribution of attentional resources. Human factors theories suggest that proper utilization of the operator's sensory capacities under such conditions can improve the operator's performance and reduce the operator's workload. Using a tractor driving simulator, this study investigated whether auditory cues can be used to improve performance of the operator of an agricultural vehicle. Steering of a vehicle was simulated in visual mode (where driving error was shown to the subject using a lightbar) and in auditory mode (where a pair of speakers were used to convey the driving error direction and/or magnitude). A secondary task was also introduced in order to simulate the monitoring of an attached machine. This task included monitoring of two identical displays, which were placed behind the simulator, and responding to them, when needed, using a joystick. This task was also implemented in auditory mode (in which a beep signaled the subject to push the proper button when a response was needed) and in visual mode (in which there was no beep and visual, monitoring of the displays was necessary). Two levels of difficulty of the monitoring task were used. Deviation of the simulated vehicle from a desired straight line was used as the measure of performance in the steering task, and reaction time to the displays was used as the measure of performance in the monitoring task. Results of the experiments showed that steering performance was significantly better when steering was a visual task (driving errors were 40% to 60% of the driving errors in auditory mode), although subjective evaluations showed that auditory steering could be easier, depending on the implementation. Performance in the monitoring task was significantly better for auditory implementation (reaction time was approximately 6 times shorter), and this result was strongly supported by subjective ratings. The majority of the subjects preferred the combination of visual mode for the steering task and auditory mode for the monitoring task.

Physical Performance Tasks Required of U.S. Marines Operating in a High Altitude Cold Weather Environment.

DTIC Science & Technology

1982-07-23

readiness has not been scientifically valiated. The test batter c ists of pll-upe, sit-ups and a three-mile run e as Scoring of the PIT is arbitrary... cognitive tasks, with little information available on physical tasks cc the environmental conditions under which these tasks are to be performed. A well...environment can drastically distort operational requirements. It is difficult to convey all the encumbrances associated with maintenance of basal tasks in

The Effects of Cognitive Task Complexity on L2 Oral Production

ERIC Educational Resources Information Center

Levkina, Mayya; Gilabert, Roger

2012-01-01

This paper examines the impact of task complexity on L2 production. The study increases task complexity by progressively removing pre-task planning time and increasing the number of elements. The combined effects of manipulating these two variables of task complexity simultaneously are also analyzed. Using a repeated measures design, 42…

AGENDA: A task organizer and scheduler

NASA Technical Reports Server (NTRS)

Fratter, Isabelle

1993-01-01

AGENDA will be the main tool used in running the SPOT 4 Earth Observation Satellite's Operational Control Center. It will reduce the operator's work load and make the task easier. AGENDA sets up the work plan for a day of operations, automatically puts the day's tasks into sequence and monitors their progress in real time. Monitoring is centralized, and the tasks are run on different computers in the Center. Once informed of any problems, the operator can intervene at any time while an activity is taking place. To carry out the various functions, the operator has an advanced, efficient, ergonomic graphic interface based on X11 and OSF/MOTIF. Since AGENDA is the heart of the Center, it has to satisfy several constraints that have been taken into account during the various development phases. AGENDA is currently in its final development stages.

NASA TLA workload analysis support. Volume 1: Detailed task scenarios for general aviation and metering and spacing studies

NASA Technical Reports Server (NTRS)

Sundstrom, J. L.

1980-01-01

The techniques required to produce and validate six detailed task timeline scenarios for crew workload studies are described. Specific emphasis is given to: general aviation single pilot instrument flight rules operations in a high density traffic area; fixed path metering and spacing operations; and comparative workload operation between the forward and aft-flight decks of the NASA terminal control vehicle. The validation efforts also provide a cursory examination of the resultant demand workload based on the operating procedures depicted in the detailed task scenarios.

Throughput Enhancement of Car Exhaust Fabrication Line by Applying MOST

NASA Astrophysics Data System (ADS)

Hanash, E. A. H.; Karim, A. N. M.; Tanjong Tuan, Saravanan; Mohiuddin, A. K. M.

2017-03-01

In the fiercely competitive world market of today, manufacturers are facing increasingly tougher challenges and are compelled to find ways for productivity enhancement wherever possible in the whole supply chain. Nevertheless there are many facets in business process which can be explored for possible improvement, an immediate focus goes for the involved processes to re-engineer the activities in different workstations for an efficient and balanced assembly or fabrication line. In this paper an industrial case on fabrication line of a car exhaust system is presented to illustrate the scope of improvement by applying the MOST (Maynard’s Operation Sequence Technique) in streamlining the activities followed by assembly line balancing (ALB). The whole process of conducting various tasks is investigated to find out the lapses or wastes, to search for better option and to set the standard times for the tasks. Then individual workstation time is worked out by summing up the standard times of the involved tasks or activities and the concept of ALB is attempted to balance the fabrication line. So by possible reduction or elimination of the identified wastes or lapses workstation times including the bottleneck station are lowered. As a result the throughput of car exhaust systems is enhanced. According to the current practice, the Takt time is set at 3 minutes. However, upon an analysis through use of the MOST, the bottleneck station time is found to be as low as 1.27 minutes. Thus an opportunity of meeting the current level of demand with significantly lower workforce (with 2 operators instead of 5) is revealed. Alternatively, if necessary, an increased workload can be assigned for the current level of workforce. Moreover, with proper distribution of activities among the workstations using the concept of ALB, the line efficiency is found to be improved. So the line balance loss in the current setup of production line is also possible to be largely reduced. Thus daily production of car exhaust, if modified with suggested changes with the current workforce, could be more than double compared to the current daily output. Hence, effectiveness of the MOST followed by ALB applications to expose and remove the operational wastes in the work flow is reiterated with enhanced throughput.

A Validated Set of MIDAS V5 Task Network Model Scenarios to Evaluate Nextgen Closely Spaced Parallel Operations Concepts

NASA Technical Reports Server (NTRS)

Gore, Brian Francis; Hooey, Becky Lee; Haan, Nancy; Socash, Connie; Mahlstedt, Eric; Foyle, David C.

2013-01-01

The Closely Spaced Parallel Operations (CSPO) scenario is a complex, human performance model scenario that tested alternate operator roles and responsibilities to a series of off-nominal operations on approach and landing (see Gore, Hooey, Mahlstedt, Foyle, 2013). The model links together the procedures, equipment, crewstation, and external environment to produce predictions of operator performance in response to Next Generation system designs, like those expected in the National Airspaces NextGen concepts. The task analysis that is contained in the present report comes from the task analysis window in the MIDAS software. These tasks link definitions and states for equipment components, environmental features as well as operational contexts. The current task analysis culminated in 3300 tasks that included over 1000 Subject Matter Expert (SME)-vetted, re-usable procedural sets for three critical phases of flight; the Descent, Approach, and Land procedural sets (see Gore et al., 2011 for a description of the development of the tasks included in the model; Gore, Hooey, Mahlstedt, Foyle, 2013 for a description of the model, and its results; Hooey, Gore, Mahlstedt, Foyle, 2013 for a description of the guidelines that were generated from the models results; Gore, Hooey, Foyle, 2012 for a description of the models implementation and its settings). The rollout, after landing checks, taxi to gate and arrive at gate illustrated in Figure 1 were not used in the approach and divert scenarios exercised. The other networks in Figure 1 set up appropriate context settings for the flight deck.The current report presents the models task decomposition from the tophighest level and decomposes it to finer-grained levels. The first task that is completed by the model is to set all of the initial settings for the scenario runs included in the model (network 75 in Figure 1). This initialization process also resets the CAD graphic files contained with MIDAS, as well as the embedded operator models that comprise MIDAS. Following the initial settings, the model progresses to begin the first tasks required of the two flight deck operators, the Captain (CA) and the First Officer (FO). The task sets will initialize operator specific settings prior to loading all of the alerts, probes, and other events that occur in the scenario. As a note, the CA and FO were terms used in developing this model but the CA can also be thought of as the Pilot Flying (PF), while the FO can be considered the Pilot-Not-Flying (PNF)or Pilot Monitoring (PM). As such, the document refers to the operators as PFCA and PNFFO respectively.

Whole-body vibration in heavy equipment operators of a front-end loader: role of task exposure and tire configuration with and without traction chains.

PubMed

Blood, Ryan P; Rynell, Patrik W; Johnson, Peter W

2012-12-01

This study measured whole-body vibration (WBV) exposures in front-end loader operators, and evaluated the effects of traction chains and work tasks on their WBV exposures. WBV exposures were measured and compared across three different front-end loader tire configurations: (a) stock rubber tires, (b) rubber tires with ladder chains, and (c) rubber tires with basket chains. The operators completed three distinct standardized tasks: driving on a city street, simulated plowing, and a simulated scooping and dumping task. A portable data acquisition system collected tri-axial time weighted and raw WBV data per ISO 2631-1 and 2631-5 standards. In addition, Global Positioning System (GPS) data were collected in order to compare loader speeds across tire conditions and the standardized tasks. Relative to the stock rubber tires, both types of tire chains significantly increased WBV exposures with the ladder chains having substantially higher WBV exposures compared to basket chains. Additionally, there were task dependent differences in WBV exposures. During the driving task, the z-axis (up and down) was the predominant exposure; the plowing task had a more even distribution of exposure across all three axes; while during scooping and dumping task, the x-axis (fore and aft) had the highest WBV exposures. The GPS data indicated that there were significant speed differences across tasks but not between the basket and ladder chain conditions. Tires with ladder chains increased the front-end loader operators' exposure to WBV above the ISO 2631-1 recommended eight hour action limit increasing risk for adverse health effects. Although more expensive, basket chains are recommended over ladder chains since they substantially lowered the front-end loader operator's exposures and may ultimately reduce vibration related wear and tear on the vehicle. In order to reduce a heavy equipment vehicle (HEV) operator's chances for developing low back pain, this study provides information that health and safety professionals can use to reduce whole-body vibration (WBV) exposures when operating front-end wheel loaders with traction chains. Copyright © 2012 National Safety Council and Elsevier Ltd. All rights reserved.

Data Entry Operator: Task List Competency Record.

ERIC Educational Resources Information Center

Minnesota Instructional Materials Center, White Bear Lake.

One of 12 in the secretarial/clerical area, this booklet for the vocational instructor contains a job description for the data entry operator, a task list of areas of competency, an occupational tasks competency record (suggested as replacement for the traditional report card), a list of industry representatives and educators involved in…

High throughput manufacturing of thin-film CdTe photovoltaic modules. Annual subcontract report, 16 November 1993--15 November 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sandwisch, D W

1995-11-01

This report describes work performed by Solar Cells, Inc. (SCI), under a 3-year subcontract to advance SCI`s PV manufacturing technologies, reduce module production costs, increase module performance, and provide the groundwork for SCI to expand its commercial production capacities. SCI will meet these objectives in three phases by designing, debugging, and operating a 20-MW/year, automated, continuous PV manufacturing line that produces 60-cm {times} 120-cm thin-film CdTe PV modules. This report describes tasks completed under Phase 1 of the US Department of Energy`s PV Manufacturing Technology program.

Analysis and evaluation of processes and equipment in tasks 2 and 4 of the low-cost solar array project

NASA Technical Reports Server (NTRS)

Goldman, H.; Wolf, M.

1978-01-01

Several experimental and projected Czochralski crystal growing process methods were studied and compared to available operations and cost-data of recent production Cz-pulling, in order to elucidate the role of the dominant cost contributing factors. From this analysis, it becomes apparent that the specific add-on costs of the Cz-process can be expected to be reduced by about a factor of three by 1982, and about a factor of five by 1986. A format to guide in the accumulation of the data needed for thorough techno-economic analysis of solar cell production processes was developed.

Tele-Manipulation with Two Asymmetric Slaves: Two Operators Perform Better Than One.

PubMed

van Oosterhout, Jeroen; Heemskerk, Cock J M; de Baar, Marco R; van der Helm, Frans C T; Abbink, David A

2018-01-01

Certain tele-manipulation tasks require manipulation by two asymmetric slaves, for example, a crane for hoisting and a dexterous robotic arm for fine manipulation. It is unclear how to best design human-in-the-loop control over two asymmetric slaves. The goal of this paper is to quantitatively compare the standard approach of two co-operating operators that each control a single subtask, to a single operator performing bi-manual control over the two subtasks, and a uni-manual control approach. In a human factors experiment, participants performed a heavy load maneuvering and mounting task using a vertical crane and a robotic arm. We hypothesize that bi-manual control yields worse task performance and control activity compared to co-operation, because of conflicting spatial and temporal constraints. Literature suggests that uni-manual operators should perform better than co-operation, as co-operators critically depend on each other's actions. However, other literature provides evidence that individual operators have limited capabilities in controlling asymmetric axes of two dynamic systems. The results show that the two co-operators perform the maneuvering and mounting task faster than either bi- or uni-manual operators. Compared to co-operators, uni-manual operators required more control activity for the vertical crane and less for the robotic arm. In conclusion, this study suggests that when controlling two asymmetric slaves, a co-operating pair of operators performs better than a single operator.

Transition to the space shuttle operations era

NASA Technical Reports Server (NTRS)

1985-01-01

The tasks involved in the Space Shuttle Development Program are discussed. The ten major characteristics of an operational Shuttle are described, as well as the changes occurring in Shuttle processing, on-line operations, operations engineering, and support operations. A summary is given of tasks and goals that are being pursued in the effort to create a cost effective and efficient system.

Galileo - The Serial-Production AIT Challenge

NASA Technical Reports Server (NTRS)

Ragnit, Ulrike; Brunner, Otto

2008-01-01

The Galileo Project is one of the most demanding projects of ESA, being Europe's autarkic navigation system and a constellation composed of 30 satellites. This presentation points out the different phases of the project up to the full operational capability and the corresponding launch options with respect to launch vehicles as well as launch configurations. One of the biggest challenges is to set up a small serial 'production line' for the overall integration and test campaign of satellites. This production line demands an optimization of all relevant tasks, taking into account also backup and recovery actions. A comprehensive AIT concept is required, reflecting a tightly merged facility layout and work flow design. In addition a common data management system is needed to handle all spacecraft related documentation and to have a direct input-out flow for all activities, phases and positions at the same time. Process optimization is a well known field of engineering in all small high tech production lines, nevertheless serial production of satellites are still not the daily task in space business and therefore new concepts have to be put in place. Therefore, and in order to meet the satellites overall system optimization, a thorough interface between unit/subsystem manufacturing and satellite AIT must be realized to ensure a smooth flow and to avoid any process interruption, which would directly lead to a schedule impact.

The neural dynamics of competition resolution for language production in the prefrontal cortex.

PubMed

Bourguignon, Nicolas J; Ohashi, Hiroki; Nguyen, Don; Gracco, Vincent L

2018-03-01

Previous research suggests a pivotal role of the prefrontal cortex (PFC) in word selection during tasks of confrontation naming (CN) and verb generation (VG), both of which feature varying degrees of competition between candidate responses. However, discrepancies in prefrontal activity have also been reported between the two tasks, in particular more widespread and intense activation in VG extending into (left) ventrolateral PFC, the functional significance of which remains unclear. We propose that these variations reflect differences in competition resolution processes tied to distinct underlying lexico-semantic operations: Although CN involves selecting lexical entries out of limited sets of alternatives, VG requires exploration of possible semantic relations not readily evident from the object itself, requiring prefrontal areas previously shown to be recruited in top-down retrieval of information from lexico-semantic memory. We tested this hypothesis through combined independent component analysis of functional imaging data and information-theoretic measurements of variations in selection competition associated with participants' performance in overt CN and VG tasks. Selection competition during CN engaged the anterior insula and surrounding opercular tissue, while competition during VG recruited additional activity of left ventrolateral PFC. These patterns remained after controlling for participants' speech onset latencies indicative of possible task differences in mental effort. These findings have implications for understanding the neural-computational dynamics of cognitive control in language production and how it relates to the functional architecture of adaptive behavior. © 2017 Wiley Periodicals, Inc.

Parametric identification of the process of preparing ceramic mixture as an object of control

NASA Astrophysics Data System (ADS)

Galitskov, Stanislav; Nazarov, Maxim; Galitskov, Konstantin

2017-10-01

Manufacture of ceramic materials and products largely depends on the preparation of clay raw materials. The main process here is the process of mixing, which in industrial production is mostly done in cross-compound clay mixers of continuous operation with steam humidification. The authors identified features of dynamics of this technological stage, which in itself is a non-linear control object with distributed parameters. When solving practical tasks for automation of a certain class of ceramic materials production it is important to make parametric identification of moving clay. In this paper the task is solved with the use of computational models, approximated to a particular section of a clay mixer along its length. The research introduces a methodology of computational experiments as applied to the designed computational model. Parametric identification of dynamic links was carried out according to transient characteristics. The experiments showed that the control object in question is to a great extent a non-stationary one. The obtained results are problematically oriented on synthesizing a multidimensional automatic control system for preparation of ceramic mixture with specified values of humidity and temperature exposed to the technological process of major disturbances.

Built But Not Used, Needed But Not Built: Ground System Guidance Based On Cassini-Huygens Experience

NASA Technical Reports Server (NTRS)

Larsen, Barbara S.

2006-01-01

These reflections share insight gleaned from Cassini-Huygens experience in supporting uplink operations tasks with software. Of particular interest are developed applications that were not widely adopted and tasks for which the appropriate application was not planned. After several years of operations, tasks are better understood providing a clearer picture of the mapping of requirements to applications. The impact on system design of the changing user profile due to distributed operations and greater participation of scientists in operations is also explored. Suggestions are made for improving the architecture, requirements, and design of future systems for uplink operations.

Switching between simple cognitive tasks: the interaction of top-down and bottom-up factors

NASA Technical Reports Server (NTRS)

Ruthruff, E.; Remington, R. W.; Johnston, J. C.

2001-01-01

How do top-down factors (e.g., task expectancy) and bottom-up factors (e.g., task recency) interact to produce an overall level of task readiness? This question was addressed by factorially manipulating task expectancy and task repetition in a task-switching paradigm. The effects of expectancy and repetition on response time tended to interact underadditively, but only because the traditional binary task-repetition variable lumps together all switch trials, ignoring variation in task lag. When the task-recency variable was scaled continuously, all 4 experiments instead showed additivity between expectancy and recency. The results indicated that expectancy and recency influence different stages of mental processing. One specific possibility (the configuration-execution model) is that task expectancy affects the time required to configure upcoming central operations, whereas task recency affects the time required to actually execute those central operations.

Weak and Failing States: Evolving Security Threats and U.S. Policy

DTIC Science & Technology

2008-04-18

Instability Task Force, a research group commissioned by the Central Intelligence Agency, found in a 2003 report that terrorists operate in both “ caves ...Bank Support to Low-Income Countries Under Stress (Washington, DC: The World Bank, 2006); Chauvet and Collier, “Helping Hand? Aid to Failing States...income, 50% higher debt-to-gross domestic product ratios, and double the poverty CRS-9 27 See Chauvet and Collier (2004), op. cit.; Francois Bourguignon

Navigation/Prop Software Suite

NASA Technical Reports Server (NTRS)

Bruchmiller, Tomas; Tran, Sanh; Lee, Mathew; Bucker, Scott; Bupane, Catherine; Bennett, Charles; Cantu, Sergio; Kwong, Ping; Propst, Carolyn

2012-01-01

Navigation (Nav)/Prop software is used to support shuttle mission analysis, production, and some operations tasks. The Nav/Prop suite containing configuration items (CIs) resides on IPS/Linux workstations. It features lifecycle documents, and data files used for shuttle navigation and propellant analysis for all flight segments. This suite also includes trajectory server, archive server, and RAT software residing on MCC/Linux workstations. Navigation/Prop represents tool versions established during or after IPS Equipment Rehost-3 or after the MCC Rehost.

Characterization of Cleaning and Disinfecting Tasks and Product Use Among Hospital Occupations

PubMed Central

Saito, Rena; Virji, M. Abbas; Henneberger, Paul K.; Humann, Michael J.; LeBouf, Ryan F.; Stanton, Marcia L.; Liang, Xiaoming; Stefaniak, Aleksandr B.

2016-01-01

Background Healthcare workers have an elevated prevalence of asthma and related symptoms associated with the use of cleaning/disinfecting products. The objective of this study was to identify and characterize cleaning/disinfecting tasks and products used among hospital occupations. Methods Workers from 14 occupations at five hospitals were monitored for 216 shifts, and work tasks and products used were recorded at five-minute intervals. The major chemical constituents of each product were identified from safety data sheets. Results Cleaning and disinfecting tasks were performed with a high frequency at least once per shift in many occupations. Medical equipment preparers, housekeepers, floor strippers/waxers, and endoscopy technicians spent on average 108–177 min/shift performing cleaning/disinfecting tasks. Many occupations used products containing amines and quaternary ammonium compounds for > 100 min/shift. Conclusions This analysis demonstrates that many occupations besides housekeeping incur exposures to cleaning/disinfecting products, albeit for different durations and using products containing different chemicals. PMID:25351791

Data Flow System operations: from the NTT to the VLT

NASA Astrophysics Data System (ADS)

Silva, David R.; Leibundgut, Bruno; Quinn, Peter J.; Spyromilio, Jason; Tarenghi, Massimo

1998-07-01

Science operations at the ESO very large telescope is scheduled to begin in April 1999. ESO is currently finalizing the VLT science operations plan. This plan describes the operations tasks and staffing needed to support both visitor and service mode operations. The Data Flow Systems (DFS) currently being developed by ESO will provide the infrastructure necessary for VLT science operations. This paper describes the current VLT science operations plan, first by discussing the tasks involved and then by describing the operations teams that have responsibility for those tasks. Prototypes of many of these operational concepts and tools have been in use at the ESO New Technology Telescope (NTT) since February 1997. This paper briefly summarizes the status of these prototypes and then discusses what operation lessons have been learned from the NTT experience and how they can be applied to the VLT.

The Effects of Art History-Enriched Art Therapy on Anxiety, Time on Task, and Art Product Quality.

ERIC Educational Resources Information Center

Miller, Carol L.

1993-01-01

Investigated effects of art history enrichment of art therapy task on anxiety, time on task, and art product quality among 13 chronic adult psychiatric day hospital patients. Results indicated art history enrichment task reduced anxiety and increased time on task. Art organization level tended toward significant increase compared with control…

Blinks, saccades, and fixation pauses during vigilance task performance. I., Time on task.

DOT National Transportation Integrated Search

1994-12-01

In the future, operators of complex equipment will spend more time monitoring computer controlled devices rather than having hands on control of such equipment. The operator intervenes in system operation under "unusual" conditions or when there is a...

The evaluation and quantification of respirable coal and silica dust concentrations: a task-based approach.

PubMed

Grové, T; Van Dyk, T; Franken, A; Du Plessis, J

2014-01-01

Silicosis and coal worker's pneumoconiosis are serious occupational respiratory diseases associated with the coal mining industry and the inhalation of respirable dusts containing crystalline silica. The purpose of this study (funded by the Mine Health and Safety Council of South Africa) was to evaluate the individual contributions of underground coal mining tasks to the respirable dust and respirable silica dust concentrations in an underground section by sampling the respirable dust concentrations at the intake and return of each task. The identified tasks were continuous miner (CM) cutting, construction, transfer of coal, tipping, and roof bolting. The respirable dust-generating hierarchy of the tasks from highest to lowest was: transfer of coal > CM right cutting > CM left cutting > CM face cutting > construction > roof bolting > tipping; and for respirable silica dust: CM left cutting > construction > transfer of coal > CM right cutting. Personal exposure levels were determined by sampling the exposures of workers performing tasks in the section. Respirable dust concentrations and low concentrations of respirable silica dust were found at the intake air side of the section, indicating that air entering the section is already contaminated. The hierarchy for personal respirable dust exposures was as follows, from highest to lowest: CM operator > cable handler > miner > roof bolt operator > shuttle car operator, and for respirable silica dust: shuttle car operator > CM operator > cable handler > roof bolt operator > miner. Dust control methods to lower exposures should include revision of the position of workers with regard to the task performed, positioning of the tasks with regard to the CM cutting, and proper use of the line curtains to direct ventilation appropriately. The correct use of respiratory protection should also be encouraged.

Product evaluation based in the association between intuition and tasks.

PubMed

Almeida e Silva, Caio Márcio; Okimoto, Maria Lúcia L R; Albertazzi, Deise; Calixto, Cyntia; Costa, Humberto

2012-01-01

This paper explores the importance of researching the intuitiveness in the product use. It approaches the intuitiveness influence for users that already had a visual experience of the product. Finally, it is suggested the use of a table that relates the tasks performed while using a product, the features for an intuitive use and the performance metric "task success".

Production and quality assurance automation in the Goddard Space Flight Center Flight Dynamics Facility

NASA Technical Reports Server (NTRS)

Chapman, K. B.; Cox, C. M.; Thomas, C. W.; Cuevas, O. O.; Beckman, R. M.

1994-01-01

The Flight Dynamics Facility (FDF) at the NASA Goddard Space Flight Center (GSFC) generates numerous products for NASA-supported spacecraft, including the Tracking and Data Relay Satellites (TDRS's), the Hubble Space Telescope (HST), the Extreme Ultraviolet Explorer (EUVE), and the space shuttle. These products include orbit determination data, acquisition data, event scheduling data, and attitude data. In most cases, product generation involves repetitive execution of many programs. The increasing number of missions supported by the FDF has necessitated the use of automated systems to schedule, execute, and quality assure these products. This automation allows the delivery of accurate products in a timely and cost-efficient manner. To be effective, these systems must automate as many repetitive operations as possible and must be flexible enough to meet changing support requirements. The FDF Orbit Determination Task (ODT) has implemented several systems that automate product generation and quality assurance (QA). These systems include the Orbit Production Automation System (OPAS), the New Enhanced Operations Log (NEOLOG), and the Quality Assurance Automation Software (QA Tool). Implementation of these systems has resulted in a significant reduction in required manpower, elimination of shift work and most weekend support, and improved support quality, while incurring minimal development cost. This paper will present an overview of the concepts used and experiences gained from the implementation of these automation systems.

A web-based rapid assessment tool for production publishing solutions

NASA Astrophysics Data System (ADS)

Sun, Tong

2010-02-01

Solution assessment is a critical first-step in understanding and measuring the business process efficiency enabled by an integrated solution package. However, assessing the effectiveness of any solution is usually a very expensive and timeconsuming task which involves lots of domain knowledge, collecting and understanding the specific customer operational context, defining validation scenarios and estimating the expected performance and operational cost. This paper presents an intelligent web-based tool that can rapidly assess any given solution package for production publishing workflows via a simulation engine and create a report for various estimated performance metrics (e.g. throughput, turnaround time, resource utilization) and operational cost. By integrating the digital publishing workflow ontology and an activity based costing model with a Petri-net based workflow simulation engine, this web-based tool allows users to quickly evaluate any potential digital publishing solutions side-by-side within their desired operational contexts, and provides a low-cost and rapid assessment for organizations before committing any purchase. This tool also benefits the solution providers to shorten the sales cycles, establishing a trustworthy customer relationship and supplement the professional assessment services with a proven quantitative simulation and estimation technology.

Use of a pitch adjustable foot restraint system: Operator strength capability and load requirements

NASA Technical Reports Server (NTRS)

Wilmington, Robert P.; Poliner, Jeffrey; Klute, Glenn K.

1994-01-01

The zero-gravity environment creates a need for a proper human body restraint system to maintain a comfortable posture with less fatigue and to maximize productivity. In addition, restraint systems must be able to meet the loading demands of maintenance and assembly tasks performed on orbit. The shuttle's primary intravehicular astronaut restraint system is currently a foot loop design that attaches to flat surfaces on the shuttle, allowing for varying mounting locations and easy egress and ingress. However, this design does not allow for elevation, pitch, or foot loop length adjustment. Several prototype foot restraint systems are being evaluated for use aboard the space station and the space shuttle. The JSC Anthropometry and Biomechanics Laboratory initiated this study to quantify the maximum axial forces and moments that would be induced on a foot loop type of restraint while operators performed a torque wrench task, also allowing for angling the restraint pitch angle to study yet another effect. Results indicate that the greatest forces into the torque wrench and into the foot restraint system occur while the operator performs an upward effort. This study did not see any significant difference in the operators' force due to pitch orientation. Thus, in a work environment in which hand holds are available, no significant influence of the pitch angle on forces imparted to the restraint system existed.

Reconfirmation of frit 803 based on the January 2016 sludge batch 9 reprojection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, F.; Edwards, T.

2016-02-10

On January 11, 2016, Savannah River Remediation (SRR) provided the Savannah River National Laboratory (SRNL) with a Sludge Batch 9 (SB9) reprojection that was developed from the analyzed composition of a Tank 51 sample. This sample was collected after field washing had been completed in Tank 51 to support the alternate reductant task. Based on this reprojection, Frit 803 is still a viable option for the processing of SB9 under sludge-only operations and coupled (Actinide Removal Process (ARP) product with and without monosodium titanate (MST)) operations. The maximum projected volumes of ARP product that can be transferred from the Precipitatemore » Reactor Feed Tank (PRFT) per Sludge Receipt and Adjustment Tank (SRAT) batch and the resulting Na 2O concentrations in the SRAT for coupled operations were determined. The Na 2O concentrations in the SRAT resulting from the maximum projected ARP product transfer volumes are consistent with those from the previous assessments that were based on the August 2015 projections. Regardless of the presence or absence of MST in the ARP product, the contribution of Na 2O to the resulting glass will be similar at the same waste loading (WL). These projected volumes of ARP product are not anticipated to be an issue for SB9. The actual transfer volumes from the PRFT to the SRAT are determined based upon the analyzed Na 2O concentrations in the PRFT samples, which has resulted in larger transfer volumes than those allowed by the projections for Sludge Batch 8 (SB8). An operating window of 32-40% WL around the nominal WL of 36% is achievable for both sludge-only and coupled operations; however, each of the glass systems studied does become limited by waste form affecting constraints (durability) at higher volumes of ARP product and WLs of 41-42%.« less

Cognitive Task Analysis and Work-Centered Support System Recommendations for a Deployed Network Operations Support Center (NOSC-D)

DTIC Science & Technology

2001-08-01

This report presents the results of a preliminary Cognitive Task Analysis (CTA) of the deployed Network Operations Support Center (NOSC-D), and the...conducted Cognitive Task Analysis interviews with four (4) NOSC-D personnel. Because of the preliminary nature of the finding, the analysis is

Blast optimization for improved dragline productivity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Humphreys, M.; Baldwin, G.

1994-12-31

A project aimed at blast optimization for large open pit coal mines is utilizing blast monitoring and analysis techniques, advanced dragline monitoring equipment, and blast simulation software, to assess the major controlling factors affecting both blast performance and subsequent dragline productivity. This has involved collaborative work between the explosives supplier, mine operator, monitoring equipment manufacturer, and a mining research organization. The results from trial blasts and subsequently monitored dragline production have yielded promising results and continuing studies are being conducted as part of a blast optimization program. It should be stressed that the optimization of blasting practices for improved draglinemore » productivity is a site specific task, achieved through controlled and closely monitored procedures. The benefits achieved at one location can not be simply transferred to another minesite unless similar improvement strategies are first implemented.« less

The Hierarchical Structure of Formal Operational Tasks.

ERIC Educational Resources Information Center

Bart, William M.; Mertens, Donna M.

1979-01-01

The hierarchical structure of the formal operational period of Piaget's theory of cognitive development was explored through the application of ordering theoretical methods to a set of data that systematically utilized the various formal operational schemes. Results suggested a common structure underlying task performance. (Author/BH)

Combining Variables, Controlling Variables, and Proportions: Is There a Psychological Link?

ERIC Educational Resources Information Center

Lawson, Anton E.

1979-01-01

Investigated the degree of relationship among the performance of 28 seventh grade students on the following three formal operations tasks: chemical combinations, bending rods, and balance beam. Results show that task performance ranged widely from early concrete operational to fully operational. (HM)

Factor Structure of the Piagetian Stage of Concrete Operations.

ERIC Educational Resources Information Center

Klausmeier, Herbert J.; Sipple, Thomas S.

1982-01-01

The Piagetian developmental stage of concrete operational thought and the theoretical groupement structures underlying children's performance of 12 concrete operations tasks are discussed. Tasks were shown to develop in five related sets. Three factor structures were found in this longitudinal study. (Author/CM)

NDSI products system based on Hadoop platform

NASA Astrophysics Data System (ADS)

Zhou, Yan; Jiang, He; Yang, Xiaoxia; Geng, Erhui

2015-12-01

Snow is solid state of water resources on earth, and plays an important role in human life. Satellite remote sensing is significant in snow extraction with the advantages of cyclical, macro, comprehensiveness, objectivity, timeliness. With the continuous development of remote sensing technology, remote sensing data access to the trend of multiple platforms, multiple sensors and multiple perspectives. At the same time, in view of the remote sensing data of compute-intensive applications demand increase gradually. However, current the producing system of remote sensing products is in a serial mode, and this kind of production system is used for professional remote sensing researchers mostly, and production systems achieving automatic or semi-automatic production are relatively less. Facing massive remote sensing data, the traditional serial mode producing system with its low efficiency has been difficult to meet the requirements of mass data timely and efficient processing. In order to effectively improve the production efficiency of NDSI products, meet the demand of large-scale remote sensing data processed timely and efficiently, this paper build NDSI products production system based on Hadoop platform, and the system mainly includes the remote sensing image management module, NDSI production module, and system service module. Main research contents and results including: (1)The remote sensing image management module: includes image import and image metadata management two parts. Import mass basis IRS images and NDSI product images (the system performing the production task output) into HDFS file system; At the same time, read the corresponding orbit ranks number, maximum/minimum longitude and latitude, product date, HDFS storage path, Hadoop task ID (NDSI products), and other metadata information, and then create thumbnails, and unique ID number for each record distribution, import it into base/product image metadata database. (2)NDSI production module: includes the index calculation, production tasks submission and monitoring two parts. Read HDF images related to production task in the form of a byte stream, and use Beam library to parse image byte stream to the form of Product; Use MapReduce distributed framework to perform production tasks, at the same time monitoring task status; When the production task complete, calls remote sensing image management module to store NDSI products. (3)System service module: includes both image search and DNSI products download. To image metadata attributes described in JSON format, return to the image sequence ID existing in the HDFS file system; For the given MapReduce task ID, package several task output NDSI products into ZIP format file, and return to the download link (4)System evaluation: download massive remote sensing data and use the system to process it to get the NDSI products testing the performance, and the result shows that the system has high extendibility, strong fault tolerance, fast production speed, and the image processing results with high accuracy.

Computing shifts to monitor ATLAS distributed computing infrastructure and operations

NASA Astrophysics Data System (ADS)

Adam, C.; Barberis, D.; Crépé-Renaudin, S.; De, K.; Fassi, F.; Stradling, A.; Svatos, M.; Vartapetian, A.; Wolters, H.

2017-10-01

The ATLAS Distributed Computing (ADC) group established a new Computing Run Coordinator (CRC) shift at the start of LHC Run 2 in 2015. The main goal was to rely on a person with a good overview of the ADC activities to ease the ADC experts’ workload. The CRC shifter keeps track of ADC tasks related to their fields of expertise and responsibility. At the same time, the shifter maintains a global view of the day-to-day operations of the ADC system. During Run 1, this task was accomplished by a person of the expert team called the ADC Manager on Duty (AMOD), a position that was removed during the shutdown period due to the reduced number and availability of ADC experts foreseen for Run 2. The CRC position was proposed to cover some of the AMODs former functions, while allowing more people involved in computing to participate. In this way, CRC shifters help with the training of future ADC experts. The CRC shifters coordinate daily ADC shift operations, including tracking open issues, reporting, and representing ADC in relevant meetings. The CRC also facilitates communication between the ADC experts team and the other ADC shifters. These include the Distributed Analysis Support Team (DAST), which is the first point of contact for addressing all distributed analysis questions, and the ATLAS Distributed Computing Shifters (ADCoS), which check and report problems in central services, sites, Tier-0 export, data transfers and production tasks. Finally, the CRC looks at the level of ADC activities on a weekly or monthly timescale to ensure that ADC resources are used efficiently.

The Differential Effects of Two Types of Task Repetition on the Complexity, Accuracy, and Fluency in Computer-Mediated L2 Written Production: A Focus on Computer Anxiety

ERIC Educational Resources Information Center

Amiryousefi, Mohammad

2016-01-01

Previous task repetition studies have primarily focused on how task repetition characteristics affect the complexity, accuracy, and fluency in L2 oral production with little attention to L2 written production. The main purpose of the study reported in this paper was to examine the effects of task repetition versus procedural repetition on the…

Human factors approach to evaluate the user interface of physiologic monitoring.

PubMed

Fidler, Richard; Bond, Raymond; Finlay, Dewar; Guldenring, Daniel; Gallagher, Anthony; Pelter, Michele; Drew, Barbara; Hu, Xiao

2015-01-01

As technology infiltrates more of our personal and professional lives, user expectations for intuitive design have driven many consumer products, while medical equipment continues to have high training requirements. Not much is known about the usability and user experience associated with hospital monitoring equipment. This pilot project aimed to better understand and describe the user interface interaction and user experience with physiologic monitoring technology. This was a prospective, descriptive, mixed-methods quality improvement project to analyze perceptions and task analyses of physiologic monitors. Following a survey of practice patterns and perceived abilities to accomplish key tasks, 10 voluntary experienced physician and nurse subjects were asked to perform a series of tasks in 7 domains of monitor operations on GE Monitoring equipment in a single institution. For each task analysis, data were collected on time to complete the task, the number of button pushes or clicks required to accomplish the task, economy of motion, and observed errors. Although 60% of the participants reported incorporating monitoring data into patient care, 80% of participants preferred to receive monitoring data at the point of care (bedside). Average perceived central station usability is 5.3 out of 10 (ten is easiest). High variability exists in monitoring station interaction performance among those participating in this project. Alarms were almost universally silenced without cognitive recognition of the alarm state. Education related to monitoring operations appeared largely absent in this sample. Most users perceived the interface to not be intuitive, complaining of multiple layers and steps for data retrieval. These clinicians report real-time monitoring helpful for abrupt changes in condition like arrhythmias; however, reviewing alarms is not prioritized as valuable due to frequent false alarms. Participants requested exporting monitoring data to electronic medical records. Much research is needed to develop best practices for display of real-time information, organization and filtering of meaningful data, and simplified ways to find information. Published by Elsevier Inc.

HEPS4Power - Extended-range Hydrometeorological Ensemble Predictions for Improved Hydropower Operations and Revenues

NASA Astrophysics Data System (ADS)

Bogner, Konrad; Monhart, Samuel; Liniger, Mark; Spririg, Christoph; Jordan, Fred; Zappa, Massimiliano

2015-04-01

In recent years large progresses have been achieved in the operational prediction of floods and hydrological drought with up to ten days lead time. Both the public and the private sectors are currently using probabilistic runoff forecast in order to monitoring water resources and take actions when critical conditions are to be expected. The use of extended-range predictions with lead times exceeding 10 days is not yet established. The hydropower sector in particular might have large benefits from using hydro meteorological forecasts for the next 15 to 60 days in order to optimize the operations and the revenues from their watersheds, dams, captions, turbines and pumps. The new Swiss Competence Centers in Energy Research (SCCER) targets at boosting research related to energy issues in Switzerland. The objective of HEPS4POWER is to demonstrate that operational extended-range hydro meteorological forecasts have the potential to become very valuable tools for fine tuning the production of energy from hydropower systems. The project team covers a specific system-oriented value chain starting from the collection and forecast of meteorological data (MeteoSwiss), leading to the operational application of state-of-the-art hydrological models (WSL) and terminating with the experience in data presentation and power production forecasts for end-users (e-dric.ch). The first task of the HEPS4POWER will be the downscaling and post-processing of ensemble extended-range meteorological forecasts (EPS). The goal is to provide well-tailored forecasts of probabilistic nature that should be reliable in statistical and localized at catchment or even station level. The hydrology related task will consist in feeding the post-processed meteorological forecasts into a HEPS using a multi-model approach by implementing models with different complexity. Also in the case of the hydrological ensemble predictions, post-processing techniques need to be tested in order to improve the quality of the forecasts against observed discharge. Analysis should be specifically oriented to the maximisation of hydroelectricity production. Thus, verification metrics should include economic measures like cost loss approaches. The final step will include the transfer of the HEPS system to several hydropower systems, the connection with the energy market prices and the development of probabilistic multi-reservoir production and management optimizations guidelines. The baseline model chain yielding three-days forecasts established for a hydropower system in southern-Switzerland will be presented alongside with the work-plan to achieve seasonal ensemble predictions.

Robotic lunar surface operations: Engineering analysis for the design, emplacement, checkout and performance of robotic lunar surface systems

NASA Technical Reports Server (NTRS)

Woodcock, Gordon R.

1990-01-01

The assembly, emplacement, checkout, operation, and maintenance of equipment on planetary surfaces are all part of expanding human presence out into the solar system. A single point design, a reference scenario, is presented for lunar base operations. An initial base, barely more than an output, which starts from nothing but then quickly grows to sustain people and produce rocket propellant. The study blended three efforts: conceptual design of all required surface systems; assessments of contemporary developments in robotics; and quantitative analyses of machine and human tasks, delivery and work schedules, and equipment reliability. What emerged was a new, integrated understanding of hot to make a lunar base happen. The overall goal of the concept developed was to maximize return, while minimizing cost and risk. The base concept uses solar power. Its primary industry is the production of liquid oxygen for propellant, which it extracts from native lunar regolith. Production supports four lander flights per year, and shuts down during the lunar nighttime while maintenance is performed.

Environmental health impact in the hospital laundry.

PubMed

Byrns, G E; Bland, L A

1980-01-01

The task of surveying the hospital laundry is often dismissed by public health officials as unnecessary because the laundry cycle is generally considered to be capable of destroying all pathogens. Even though a properly operated laundry can produce a relatively bacteria free product, there are a number of variables that have an impact on the bacterial quality of the linen before it reaches the patient. It is vital that surveillance personnel understand these factors during processing, transporting, or sorting linen so that the final product is aesthetically, chemically, and bacteriologically acceptable for patient use. At the U. S. Public Health Service Hospital laundry in New Orleans, surveillance by the Environmental Health Department has identified potential problem areas. Operational improvements have been instituted at this laundry that would not have been possible without a thorough understanding of the laundry cycle. The authors describe the laundry cycle, including potential problem areas; identify useful microbial and chemical surveillance methods; and discuss process control procedures. This information will help the environmental health worker in discussions with laundry personnel regarding contamination control and operational efficiency.

Erroneous knowledge of results affects decision and memory processes on timing tasks.

PubMed

Ryan, Lawrence J; Fritz, Matthew S

2007-12-01

On mental timing tasks, erroneous knowledge of results (KR) leads to incorrect performance accompanied by the subjective judgment of accurate performance. Using the start-stop technique (an analogue of the peak interval procedure) with both reproduction and production timing tasks, the authors analyze what processes erroneous KR alters. KR provides guidance (performance error information) that lowers decision thresholds. Erroneous KR also provides targeting information that alters response durations proportionately to the magnitude of the feedback error. On the production task, this shift results from changes in the reference memory, whereas on the reproduction task this shift results from changes in the decision threshold for responding. The idea that erroneous KR can alter different cognitive processes on related tasks is supported by the authors' demonstration that the learned strategies can transfer from the reproduction task to the production task but not visa versa. Thus effects of KR are both task and context dependent.

Improving Language Production Using Subtitled Similar Task Videos

ERIC Educational Resources Information Center

Arslanyilmaz, Abdurrahman; Pedersen, Susan

2010-01-01

This study examines the effects of subtitled similar task videos on language production by nonnative speakers (NNSs) in an online task-based language learning (TBLL) environment. Ten NNS-NNS dyads collaboratively completed four communicative tasks, using an online TBLL environment specifically designed for this study and a chat tool in…

Applied Meteorology Unit (AMU) Quarterly Report - Fourth Quarter FY-10

NASA Technical Reports Server (NTRS)

Bauman, William; Crawford, Winifred; Barrett, Joe; Watson, Leela; Wheeler, Mark

2010-01-01

Three AMU tasks were completed in this Quarter, each resulting in a forecast tool now being used in operations and a final report documenting how the work was done. AMU personnel completed the following tasks (1) Phase II of the Peak Wind Tool for General Forecasting task by delivering an improved wind forecasting tool to operations and providing training on its use; (2) a graphical user interface (GUI) she updated with new scripts to complete the ADAS Update and Maintainability task, and delivered the scripts to the Spaceflight Meteorology Group on Johnson Space Center, Texas and National Weather Service in Melbourne, Fla.; and (3) the Verify MesoNAM Performance task after we created and delivered a GUI that forecasters will use to determine the performance of the operational MesoNAM weather model forecast.

CO2Explorer: Conducting Greenhouse-Gas Measurements of Landfills using a Small Fixed-wing UAV

NASA Astrophysics Data System (ADS)

Hollingsworth, Peter; Allen, Grant; Kabbabe, Khristopher; Pitt, Joseph

2017-04-01

Quantifying inventories of Greenhouse gas emissions, primarily Methane and Carbon Dioxide, from distributed sources such as a landfill has historically been undertaken using one of several ground based measurement techniques. These methods are either time and/or resource intensive. As a result regulatory agencies have started looking at the potential of using small-unmanned aircraft to supplement or supplant the current methods. The challenge of using a UAV to perform these tasks is the trade-off between accuracy, operational flexibility and operational productivity. This is driven by the state-of-the-art in measurement instruments, the operating environment at landfills and the regulatory/safety environment surrounding UAV operations. This work describes the development of the operational concept, and associated UAV measurement platform for the CO2Explorer. It looks at the scientific, engineering and possible policy trades and compares the use of small rotary and fixed-wing UAVs from both an operational and measurement perspective. This work also makes recommendations on system development and operation for users lacking in both systems engineering and operational experience.

Scaling up a CMS tier-3 site with campus resources and a 100 Gb/s network connection: what could go wrong?

NASA Astrophysics Data System (ADS)

Wolf, Matthias; Woodard, Anna; Li, Wenzhao; Hurtado Anampa, Kenyi; Tovar, Benjamin; Brenner, Paul; Lannon, Kevin; Hildreth, Mike; Thain, Douglas

2017-10-01

The University of Notre Dame (ND) CMS group operates a modest-sized Tier-3 site suitable for local, final-stage analysis of CMS data. However, through the ND Center for Research Computing (CRC), Notre Dame researchers have opportunistic access to roughly 25k CPU cores of computing and a 100 Gb/s WAN network link. To understand the limits of what might be possible in this scenario, we undertook to use these resources for a wide range of CMS computing tasks from user analysis through large-scale Monte Carlo production (including both detector simulation and data reconstruction.) We will discuss the challenges inherent in effectively utilizing CRC resources for these tasks and the solutions deployed to overcome them.

TDRSS system configuration study for space shuttle program

NASA Technical Reports Server (NTRS)

1978-01-01

This study was set up to assure that operation of the shuttle orbiter communications systems met the program requirements when subjected to electrical conditions similar to those which will be encountered during the operational mission. The test program intended to implement an integrated test bed, consisting of applicable orbiter, EVA, payload simulator, STDN, and AF/SCF, as well as the TDRSS equipment. The stated intention of Task 501 Program was to configure the test bed with prototype hardware for a system development test and production hardware for a system verification test. In case of TDRSS when the hardware was not available, simulators whose functional performance was certified to meet appropriate end item specification were used.

Item Mass and Complexity and the Arithmetic Computation of Students with Learning Disabilities.

ERIC Educational Resources Information Center

Cawley, John F.; Shepard, Teri; Smith, Maureen; Parmar, Rene S.

1997-01-01

The performance of 76 students (ages 10 to 15) with learning disabilities on four tasks of arithmetic computation within each of the four basic operations was examined. Tasks varied in difficulty level and number of strokes needed to complete all items. Intercorrelations between task sets and operations were examined as was the use of…

The Endurance of Children's Working Memory: A Recall Time Analysis

ERIC Educational Resources Information Center

Towse, John N.; Hitch, Graham J.; Hamilton, Z.; Pirrie, Sarah

2008-01-01

We analyze the timing of recall as a source of information about children's performance in complex working memory tasks. A group of 8-year-olds performed a traditional operation span task in which sequence length increased across trials and an operation period task in which processing requirements were extended across trials of constant sequence…

Cognitive Task Analysis of the HALIFAX-Class Operations Room Officer: Data Sheets. Annexes

DTIC Science & Technology

1999-03-10

Image Cover Sheet CLASSIFICATION SYSTEM NUMBER 510920 UNCLASSIFIED 1111111111111111111111111111111111111111 TITLE ANNEXES TO: COGNITIVE TASK ANALYSIS OF...1999 2. REPORT TYPE 3. DATES COVERED 00-00-1999 to 00-00-1999 4. TITLE AND SUBTITLE Annexes to: Cognitive Task Analysis of the HALIFAX-Class...by ANSI Std Z39-18 Guelph, Ontario .H U. M A N S X S T E M S Incorporated Annexes to: Cognitive Task Analysis of the HALIFAX-Class Operations

Application of manual control theory to the study of biological stress

NASA Technical Reports Server (NTRS)

Replogle, C. R.; Holden, F. M.; Iay, C. N.

1972-01-01

A study was run using both a stable, third-order task and an adaptive first-order unstable task singly and in combination to test the effects of 2 min hypoxia (22000 ft) on human operator. The results indicate that the RMS error in the stable task does not change as a function of hypoxic stress whereas the error in an unstable task changes significantly. Models involving human operator parameter changes and noise injection are discussed.

Task-oriented display design - Concept and example

NASA Technical Reports Server (NTRS)

Abbott, Terence S.

1989-01-01

The general topic was in the area of display design alternatives for improved man-machine performance. The intent was to define and assess a display design concept oriented toward providing this task-oriented information. The major focus of this concept deals with the processing of data into parameters that are more relevant to the task of the human operator. Closely coupled to this concept of relevant information is the form or manner in which this information is actually presented. Conventional forms of presentation are normally a direct representation of the underlying data. By providing information in a form that is more easily assimilated and understood, a reduction in human error and cognitive workload may be obtained. A description of this proposed concept with a design example is provided. The application for the example was an engine display for a generic, twin-engine civil transport aircraft. The product of this concept was evaluated against a functionally similar, traditional display. The results of this evaluation showed that a task-oriented approach to design is a viable concept with regard to reducing user error and cognitive workload. The goal of this design process, providing task-oriented information to the user, both in content and form, appears to be a feasible mechanism for increasing the overall performance of a man-machine system.

Task-oriented display design: Concept and example

NASA Technical Reports Server (NTRS)

Abbott, Terence S.

1989-01-01

The general topic was in the area of display design alternatives for improved man-machine performance. The intent was to define and assess a display design concept oriented toward providing this task-oriented information. The major focus of this concept deals with the processing of data into parameters that are more relevant to the task of the human operator. Closely coupled to this concept of relevant information is the form or manner in which this information is actually presented. Conventional forms of presentation are normally a direct representation of the underlying data. By providing information in a form that is more easily assimilated and understood, a reduction in human error and cognitive workload may be obtained. A description of this proposed concept with a design example is provided. The application for the example was an engine display for a generic, twin-engine civil transport aircraft. The product of this concept was evaluated against a functionally similar, traditional display. The results of this evaluation showed that a task-oriented approach to design is a viable concept with regard to reducing user error and cognitive workload. The goal of this design process, providing task-oriented information to the user, both in content and form, appears to be a feasible mechanism for increasing the overall performance of a man-machine system.

Enhanced control & sensing for the REMOTEC ANDROS Mk VI robot. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spelt, P.F.; Harvey, H.W.

1997-08-01

This Cooperative Research and Development Agreement (CRADA) between Lockheed Marietta Energy Systems, Inc., and REMOTEC, Inc., explored methods of providing operator feedback for various work actions of the ANDROS Mk VI teleoperated robot. In a hazardous environment, an extremely heavy workload seriously degrades the productivity of teleoperated robot operators. This CRADA involved the addition of computer power to the robot along with a variety of sensors and encoders to provide information about the robot`s performance in and relationship to its environment. Software was developed to integrate the sensor and encoder information and provide control input to the robot. ANDROS Mkmore » VI robots are presently used by numerous electric utilities to perform tasks in reactors where substantial exposure to radiation exists, as well as in a variety of other hazardous environments. Further, this platform has potential for use in a number of environmental restoration tasks, such as site survey and detection of hazardous waste materials. The addition of sensors and encoders serves to make the robot easier to manage and permits tasks to be done more safely and inexpensively (due to time saved in the completion of complex remote tasks). Prior research on the automation of mobile platforms with manipulators at Oak Ridge National Laboratory`s Center for Engineering Systems Advanced Research (CESAR, B&R code KC0401030) Laboratory, a BES-supported facility, indicated that this type of enhancement is effective. This CRADA provided such enhancements to a successful working teleoperated robot for the first time. Performance of this CRADA used the CESAR laboratory facilities and expertise developed under BES funding.« less

A general-purpose development environment for intelligent computer-aided training systems

NASA Technical Reports Server (NTRS)

Savely, Robert T.

1990-01-01

Space station training will be a major task, requiring the creation of large numbers of simulation-based training systems for crew, flight controllers, and ground-based support personnel. Given the long duration of space station missions and the large number of activities supported by the space station, the extension of space shuttle training methods to space station training may prove to be impractical. The application of artificial intelligence technology to simulation training can provide the ability to deliver individualized training to large numbers of personnel in a distributed workstation environment. The principal objective of this project is the creation of a software development environment which can be used to build intelligent training systems for procedural tasks associated with the operation of the space station. Current NASA Johnson Space Center projects and joint projects with other NASA operational centers will result in specific training systems for existing space shuttle crew, ground support personnel, and flight controller tasks. Concurrently with the creation of these systems, a general-purpose development environment for intelligent computer-aided training systems will be built. Such an environment would permit the rapid production, delivery, and evolution of training systems for space station crew, flight controllers, and other support personnel. The widespread use of such systems will serve to preserve task and training expertise, support the training of many personnel in a distributed manner, and ensure the uniformity and verifiability of training experiences. As a result, significant reductions in training costs can be realized while safety and the probability of mission success can be enhanced.

GPS net­work operations for the International GPS Geodynamics Service

USGS Publications Warehouse

Neilan, Ruth E.

1993-01-01

As GPS technology comes of age in the 1990’s, it is evident that an internationally sponsored GPS tracking system is called for to provide consistent, timely ground tracking data and data products to the geophysical community. The planning group for the International GPS Geodynamics Service (IGS), sponsored by the International Association of Geodesy (IAG), is addressing all elements of the end-to-end tracking system, ranging from data collection to data analysis and distribution of products (Mueller, 1992). Part of the planning process is to formulate how these various elements work together to create the common infrastructure needed to support a wide variety of GPS investigations. A key element for any permanent satellite tracking system is certainly the acquisition segment; the reliability and robustness of the ground network operations directly determine the fates and limitations of final products. The IGS planning group therefore included a committee tasked to develop and establish standards governing data acquisition and site-specific characteristics deemed necessary to ensure the collection of a high quality, continuous data set.

30 CFR 48.7 - Training of miners assigned to a task in which they have had no previous experience; minimum...

Code of Federal Regulations, 2010 CFR

2010-07-01

... to new work tasks as mobile equipment operators, drilling machine operators, haulage and conveyor... protective measures a miner can take against these hazards, and the contents of the mine's HazCom program... operation in the mine, which require new or different operating procedures. (4) Such other courses as may be...

The physical work environment and end-user requirements: Investigating marine engineering officers' operational demands and ship design.

PubMed

Mallam, Steven C; Lundh, Monica

2016-08-12

Physical environments influence how individuals perceive a space and behave within it. Previous research has revealed deficiencies in ship engine department work environments, and their impact on crew productivity, health and wellbeing. Connect operational task demands to pragmatic physical design and layout solutions by implementing a user-centric perspective. Three focus groups, each consisting of three marine engineers participated in this study. Focus groups were divided into two sessions: first, to investigate the end-user's operational requirements and their relationship with ship physical design and layout. Second, criteria formulated from group discussions were applied to a ship design case study. All focus group sessions were audio recorded and transcribed verbatim. The data were analyzed using Grounded Theory. Design choices made in a ships general arrangement were described to inherently influence how individuals and teams are able to function within the system. Participants detailed logistical relationships between key areas, stressing that the work environment and physical linkages must allow for flexibility of work organization and task execution. Traditional engine control paradigms do not allow effective mitigation of traditional engine department challenges. The influence of technology and modernization of ship systems can facilitate improvement of physical environments and work organization if effectively utilized.

M.E.366-J embodiment design project: Portable foot restraint

NASA Technical Reports Server (NTRS)

Heaton, Randall; Meyer, Eikar; Schmidt, Davey; Enders, Kevin

1994-01-01

During space shuttle operations, astronauts require support to carry out tasks in the weightless environment. In the past, portable foot restraints (PFR) with orientations adjustable in pitch, roll, and yaw provided this support for payload bay operations. These foot restraints, however, were designed for specific tasks with a load limit of 111.2 Newtons. Since the original design, new applications for foot restraints have been identified. New designs for the foot restraints have been created to boost the operational work load to 444.8 Newtons and decrease setup times. What remains to be designed is an interface between the restraint system and the extravehicular mobility unit (EMU) boots. NASA provided a proposed locking device involving a spring-loaded mechanism. This locking mechanism must withstand loads of 1334.4 Newtons in any direction and weigh less than 222.4 Newtons. This paper develops an embodiment design for the interface between the PFR and the EMU boots. This involves design of the locking mechanism and a removable cleat that allows the boot to interface with this mechanism. The design team used the Paul Beitz engineering methodology to present the systematic development, structural analysis, and production considerations of the embodiment design. This methodology provides a basis for understanding the justification behind the decisions made in the design.

Work-Related Musculoskeletal Symptoms and Job Factors Among Large-Herd Dairy Milkers.

PubMed

Douphrate, David I; Nonnenmann, Matthew W; Hagevoort, Robert; Gimeno Ruiz de Porras, David

2016-01-01

Dairy production in the United States is moving towards large-herd milking operations, resulting in an increase in task specialization and work demands. The objective of this project was to provide preliminary evidence of the association of a number of specific job conditions that commonly characterize large-herd parlor milking operations with work-related musculoskeletal symptoms (MSS). A modified version of the Standardized Nordic Questionnaire was administered to assess MSS prevalence among 450 US large-herd parlor workers. Worker demographics and MSS prevalences were generated. Prevalence ratios were also generated to determine associations of a number of specific job conditions that commonly characterize large-herd parlor milking operations with work-related MSS. Work-related MSS are prevalent among large-herd parlor workers, since nearly 80% report 12-month prevalences of one or more symptoms, which are primarily located in the upper extremities, specifically shoulders and wrist/hand. Specific large-herd milking parlor job conditions are associated with MSS in multiple body regions, including performing the same task repeatedly, insufficient rest breaks, working when injured, static postures, adverse environmental conditions, and reaching overhead. These findings support the need for administrative and engineering solutions aimed at reducing exposure to job risk factors for work-related MSS among large-herd parlor workers.

An evaluation of the production effects of video self-modeling.

PubMed

O'Handley, Roderick D; Allen, Keith D

2017-12-01

A multiple baseline across tasks design was used to evaluate the production effects of video self-modeling on three activities of daily living tasks of an adult male with Autism Spectrum Disorder and Intellectual Disability. Results indicated large increases in task accuracy after the production of a self-modeling video for each task, but before the video was viewed by the participant. Results also indicated small increases when the participant was directed to view the same video self-models before being prompted to complete each task. Copyright © 2017 Elsevier Ltd. All rights reserved.

Monitoring cognitive and emotional processes through pupil and cardiac response during dynamic versus logical task.

PubMed

Causse, Mickaël; Sénard, Jean-Michel; Démonet, Jean François; Pastor, Josette

2010-06-01

The paper deals with the links between physiological measurements and cognitive and emotional functioning. As long as the operator is a key agent in charge of complex systems, the definition of metrics able to predict his performance is a great challenge. The measurement of the physiological state is a very promising way but a very acute comprehension is required; in particular few studies compare autonomous nervous system reactivity according to specific cognitive processes during task performance and task related psychological stress is often ignored. We compared physiological parameters recorded on 24 healthy subjects facing two neuropsychological tasks: a dynamic task that require problem solving in a world that continually evolves over time and a logical task representative of cognitive processes performed by operators facing everyday problem solving. Results showed that the mean pupil diameter change was higher during the dynamic task; conversely, the heart rate was more elevated during the logical task. Finally, the systolic blood pressure seemed to be strongly sensitive to psychological stress. A better taking into account of the precise influence of a given cognitive activity and both workload and related task-induced psychological stress during task performance is a promising way to better monitor operators in complex working situations to detect mental overload or pejorative stress factor of error.

A quantitative measure for degree of automation and its relation to system performance and mental load.

PubMed

Wei, Z G; Macwan, A P; Wieringa, P A

1998-06-01

In this paper we quantitatively model degree of automation (DofA) in supervisory control as a function of the number and nature of tasks to be performed by the operator and automation. This model uses a task weighting scheme in which weighting factors are obtained from task demand load, task mental load, and task effect on system performance. The computation of DofA is demonstrated using an experimental system. Based on controlled experiments using operators, analyses of the task effect on system performance, the prediction and assessment of task demand load, and the prediction of mental load were performed. Each experiment had a different DofA. The effect of a change in DofA on system performance and mental load was investigated. It was found that system performance became less sensitive to changes in DofA at higher levels of DofA. The experimental data showed that when the operator controlled a partly automated system, perceived mental load could be predicted from the task mental load for each task component, as calculated by analyzing a situation in which all tasks were manually controlled. Actual or potential applications of this research include a methodology to balance and optimize the automation of complex industrial systems.

Warranty optimisation based on the prediction of costs to the manufacturer using neural network model and Monte Carlo simulation

NASA Astrophysics Data System (ADS)

Stamenkovic, Dragan D.; Popovic, Vladimir M.

2015-02-01

Warranty is a powerful marketing tool, but it always involves additional costs to the manufacturer. In order to reduce these costs and make use of warranty's marketing potential, the manufacturer needs to master the techniques for warranty cost prediction according to the reliability characteristics of the product. In this paper a combination free replacement and pro rata warranty policy is analysed as warranty model for one type of light bulbs. Since operating conditions have a great impact on product reliability, they need to be considered in such analysis. A neural network model is used to predict light bulb reliability characteristics based on the data from the tests of light bulbs in various operating conditions. Compared with a linear regression model used in the literature for similar tasks, the neural network model proved to be a more accurate method for such prediction. Reliability parameters obtained in this way are later used in Monte Carlo simulation for the prediction of times to failure needed for warranty cost calculation. The results of the analysis make possible for the manufacturer to choose the optimal warranty policy based on expected product operating conditions. In such a way, the manufacturer can lower the costs and increase the profit.

A System Approach to Navy Medical Education and Training. Volume 1

DTIC Science & Technology

1974-08-31

each of the four major pro - ducts complement one another, they form, in fact, a single major product, that of the technology for improved training...the course of determining the functional limits and con - tent areas peculiar to potentially delegable tasks, it is highly desirable to be able to...NISTOS CYTO CLINICAL X-RAY LAS AST LAB ASST LAB AS SI AS SL ABI ASITO LA LAB STMIL OPERATIONS PATIENT CARE OP -- PC -- GMo GMO M.D. M.D. M.D MD M

Planning and management of the Nido Reef Complex Oil Field development, Philippines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harry, R.Y.

1981-01-01

As Operator for the Northeast Palawan consortium, Philippines-Cities Service, Inc., commenced the Philippines first commercial offshore oil production from the Nido Reef Complex Oil Field on February 1, 1979, some 11 months after a decision by management to start development. The relative speed at which design, fabrication, and construction were accomplished is attributed to the use of the concepts of project planning, task force approach, and project management. This paper presents the above concepts as applied to the Nido Complex.

Evaluation of an LED Retrofit Project at Princeton University's Carl Icahn Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, Robert; Murphy, Arthur; Perrin, Tess

At Princeton University’s Carl Icahn Laboratory, DOE’s Commercial Buildings Integration Program documented the implementation of LED retrofit products for recessed troffers, linear cove lighting, and downlights – as part of Princeton’s first building-wide interior LED project. The conversion to LED enables more extensive use of lighting controls to tailor the lighting to the task and limit the operating hours based on occupancy, and the estimated energy savings including controls is 62% compared to the incumbent system.

Risk assessment of maintenance operations: the analysis of performing task and accident mechanism.

PubMed

Carrillo-Castrillo, Jesús A; Rubio-Romero, Juan Carlos; Guadix, Jose; Onieva, Luis

2015-01-01

Maintenance operations cover a great number of occupations. Most small and medium-sized enterprises lack the appropriate information to conduct risk assessments of maintenance operations. The objective of this research is to provide a method based on the concepts of task and accident mechanisms for an initial risk assessment by taking into consideration the prevalence and severity of the maintenance accidents reported. Data were gathered from 11,190 reported accidents in maintenance operations in the manufacturing sector of Andalusia from 2003 to 2012. By using a semi-quantitative methodology, likelihood and severity were evaluated based on the actual distribution of accident mechanisms in each of the tasks. Accident mechanisms and tasks were identified by using those variables included in the European Statistics of Accidents at Work methodology. As main results, the estimated risk of the most frequent accident mechanisms identified for each of the analysed tasks is low and the only accident mechanisms with medium risk are accidents when lifting or pushing with physical stress on the musculoskeletal system in tasks involving carrying, and impacts against objects after slipping or stumbling for tasks involving movements. The prioritisation of public preventive actions for the accident mechanisms with a higher estimated risk is highly recommended.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sullivan, Kevin; Anasti, William; Fang, Yichuan

The main purpose of this project is to look at technologies and philosophies that would help reduce the costs of an Integrated Gasification Combined Cycle (IGCC) plant, increase its availability or do both. GE’s approach to this problem is to consider options in three different areas: 1) technology evaluations and development; 2) constructability approaches; and 3) design and operation methodologies. Five separate tasks were identified that fall under the three areas: Task 2 – Integrated Operations Philosophy; Task 3 – Slip Forming of IGCC Components; Task 4 – Modularization of IGCC Components; Task 5 – Fouling Removal; and Task 6more » – Improved Slag Handling. Overall, this project produced results on many fronts. Some of the ideas could be utilized immediately by those seeking to build an IGCC plant in the near future. These include the considerations from the Integrated Operations Philosophy task and the different construction techniques of Slip Forming and Modularization (especially if the proposed site is in a remote location or has a lack of a skilled workforce). Other results include ideas for promising technologies that require further development and testing to realize their full potential and be available for commercial operation. In both areas GE considers this project to be a success in identifying areas outside the core IGCC plant systems that are ripe for cost reduction and ity improvement opportunities.« less

Ergonomic Redesign of an Industrial Control Panel.

PubMed

Raeisi, S; Osqueizadeh, R; Maghsoudipour, M; Jafarpisheh, A S

2016-07-01

Operator's role in industrial control centers takes place in time, which is one of the most important determinants of whether an expected action is going to be successful or not. In certain situations, due to the complex nature of the work, the existing interfaces and already prepared procedures do not meet the dynamic requirements of operator's cognitive demands, making the control tasks unnecessarily difficult. This study was conducted to identify ergonomic issues with a specific industrial control panel, and redesign its layout and elements to enhance its usability. Task and link analysis methodologies were implemented. All essential functions and supporting operations were identified at the required trivial levels. Next, the weight of any possible link between the elements of the panel was computed as a composite index of frequency and importance. Finally, all components were rearranged within a new layout, and a computerized mockup was generated. A total of 8 primary tasks was identified, including 4 system failure handling tasks, switching between manual and automated modes, and 3 types of routine vigilance and control tasks. These tasks were broken down into 28 functions and 145 supporting operations, accordingly. Higher link values were observed between hand rest position and 2 elements. Also, 6 other components showed robust linkages. In conclusion, computer modeling can reduce the likelihood of accidents and near misses in industrial control rooms by considering the operators' misperception or mental burden and correcting poor design of the panels and inappropriate task allocation.

Multidimensional Profiling of Task Stress States for Human Factors: A Brief Review.

PubMed

Matthews, Gerald

2016-09-01

This article advocates multidimensional assessment of task stress in human factors and reviews the use of the Dundee Stress State Questionnaire (DSSQ) for evaluation of systems and operators. Contemporary stress research has progressed from an exclusive focus on environmental stressors to transactional perspectives on the stress process. Performance impacts of stress reflect the operator's dynamic attempts to understand and cope with task demands. Multidimensional stress assessments are necessary to gauge the different forms of system-operator interaction. This review discusses the theoretical and practical use of the DSSQ in evaluating multidimensional patterns of stress response. It presents psychometric evidence for the multidimensional perspective and illustrative profiles of subjective state response to task stressors and environments. Evidence is also presented on stress state correlations with related variables, including personality, stress process measures, psychophysiological response, and objective task performance. Evidence supports the validity of the DSSQ as a task stress measure. Studies of various simulated environments show that different tasks elicit different profiles of stress state response. Operator characteristics such as resilience predict individual differences in state response to stressors. Structural equation modeling may be used to understand performance impacts of stress states. Multidimensional assessment affords insight into the stress process in a variety of human factors contexts. Integrating subjective and psychophysiological assessment is a priority for future research. Stress state measurement contributes to evaluating system design, countermeasures to stress and fatigue, and performance vulnerabilities. It may also support personnel selection and diagnostic monitoring of operators. © 2016, Human Factors and Ergonomics Society.

ENVRIplus - European collaborative development of environmental infrastructures

NASA Astrophysics Data System (ADS)

Asmi, A.; Brus, M.; Kutsch, W. L.; Laj, P.

2016-12-01

European Research Infrastructures (RI) are built using ESFRI process, which dictates the steps towards a common European RIs. Building each RI separately creates unnessary barriers towards service users (e.g. on differing standards) and is not effiicient in e.g. e-science tool or data system development. To answer these inter-RI issues, the European Commission has funded several large scale cluster projectsto bring these RIs together already in planning and development phases to develop common tools, standards and methodologies, as well as learn from the exisiting systems. ENVRIplus is the cluster project for the environmental RIs in Europe, and provides platform for common development and sharing within the RI community. The project is organized around different themes, each having several workpackages with specific tasks. Major themesof the ENVRIplus are: Technical innovation, including tasks such as RI technology transfer, new observation techniques, autonomous operation, etc.; Data for science, with tasks such as RI reference model development, data discovery and citation, data publication, processing, etc.; Access to RIs, with specific tasks on interdicplinary and transnational access to RI services, and common access governance; Societal relevance and understanding, tackling on ethical issues on RI operations and understanding on human-environmental system and citizen science approaches, among others; Knowledge transfer, particularly between the RIs, and with developing RI organizations, organizing training and staff exchange; and Communication and dissemination, working towards a common environmental RI community (ENVRI community platform), and creating an own advisory RI discussion board (BEERi), and disseminating the ENVRIplus products globally. Importantly, all ENVRIplus results are open to any users from any country. Also, collaboration with international RIs and user communities are crucial to the success of the ENVRI initiatives. Overall goal is to do science globally, to answer global and regional critical challenges. The presentation will not only present the project, its state after nearly 2 years of operation, but will alsop present ideas towards building international and even more interdiciplinary collaboration on research infrastructures and their users.

Assessing performance of an Electronic Health Record (EHR) using Cognitive Task Analysis.

PubMed

Saitwal, Himali; Feng, Xuan; Walji, Muhammad; Patel, Vimla; Zhang, Jiajie

2010-07-01

Many Electronic Health Record (EHR) systems fail to provide user-friendly interfaces due to the lack of systematic consideration of human-centered computing issues. Such interfaces can be improved to provide easy to use, easy to learn, and error-resistant EHR systems to the users. To evaluate the usability of an EHR system and suggest areas of improvement in the user interface. The user interface of the AHLTA (Armed Forces Health Longitudinal Technology Application) was analyzed using the Cognitive Task Analysis (CTA) method called GOMS (Goals, Operators, Methods, and Selection rules) and an associated technique called KLM (Keystroke Level Model). The GOMS method was used to evaluate the AHLTA user interface by classifying each step of a given task into Mental (Internal) or Physical (External) operators. This analysis was performed by two analysts independently and the inter-rater reliability was computed to verify the reliability of the GOMS method. Further evaluation was performed using KLM to estimate the execution time required to perform the given task through application of its standard set of operators. The results are based on the analysis of 14 prototypical tasks performed by AHLTA users. The results show that on average a user needs to go through 106 steps to complete a task. To perform all 14 tasks, they would spend about 22 min (independent of system response time) for data entry, of which 11 min are spent on more effortful mental operators. The inter-rater reliability analysis performed for all 14 tasks was 0.8 (kappa), indicating good reliability of the method. This paper empirically reveals and identifies the following finding related to the performance of AHLTA: (1) large number of average total steps to complete common tasks, (2) high average execution time and (3) large percentage of mental operators. The user interface can be improved by reducing (a) the total number of steps and (b) the percentage of mental effort, required for the tasks. 2010 Elsevier Ireland Ltd. All rights reserved.

Operator selection for unmanned aerial systems: comparing video game players and pilots.

PubMed

McKinley, R Andy; McIntire, Lindsey K; Funke, Margaret A

2011-06-01

Popular unmanned aerial system (UAS) platforms such as the MQ-1 Predator and MQ-9 Reaper have experienced accelerated operations tempos that have outpaced current operator training regimens, leading to a shortage of qualified UAS operators. To find a surrogate to replace pilots of manned aircraft as UAS operators, this study evaluated video game players (VGPs), pilots, and a control group on a set of UAS operation relevant cognitive tasks. There were 30 participants who volunteered for this study and were divided into 3 groups: experienced pilots (P), experienced VGPs, and a control group (C). Each was trained on eight cognitive performance tasks relevant to unmanned flight tasks. The results indicated that pilots significantly outperform the VGP and control groups on multi-attribute cognitive tasks (Tank mean: VGP = 465 +/- 1.046 vs. P = 203 +/- 0.237 vs. C = 351 +/- 0.601). However, the VGPs outperformed pilots on cognitive tests related to visually acquiring, identifying, and tracking targets (final score: VGP = 594.28 +/- 8.708 vs. P = 563.33 +/- 8.787 vs. C = 568.21 +/- 8.224). Likewise, both VGPs and pilots performed similarly on the UAS landing task, but outperformed the control group (glide slope: VGP = 40.982 +/- 3.244 vs. P = 30.461 +/- 2.251 vs. C = 57.060 +/- 4.407). Cognitive skills learned in video game play may transfer to novel environments and improve performance in UAS tasks over individuals with no video game experience.

Applying Behavior-Based Robotics Concepts to Telerobotic Use of Power Tooling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Noakes, Mark W; Hamel, Dr. William R.

While it has long been recognized that telerobotics has potential advantages to reduce operator fatigue, to permit lower skilled operators to function as if they had higher skill levels, and to protect tools and manipulators from excessive forces during operation, relatively little laboratory research in telerobotics has actually been implemented in fielded systems. Much of this has to do with the complexity of the implementation and its lack of ability to operate in complex unstructured remote systems environments. One possible solution is to approach the tooling task using an adaptation of behavior-based techniques to facilitate task decomposition to a simplermore » perspective and to provide sensor registration to the task target object in the field. An approach derived from behavior-based concepts has been implemented to provide automated tool operation for a teleoperated manipulator system. The generic approach is adaptable to a wide range of typical remote tools used in hot-cell and decontamination and dismantlement-type operations. Two tasks are used in this work to test the validity of the concept. First, a reciprocating saw is used to cut a pipe. The second task is bolt removal from mockup process equipment. This paper explains the technique, its implementation, and covers experimental data, analysis of results, and suggestions for implementation on fielded systems.« less

Quality-by-Design approach to monitor the operation of a batch bioreactor in an industrial avian vaccine manufacturing process.

PubMed

Largoni, Martina; Facco, Pierantonio; Bernini, Donatella; Bezzo, Fabrizio; Barolo, Massimiliano

2015-10-10

Monitoring batch bioreactors is a complex task, due to the fact that several sources of variability can affect a running batch and impact on the final product quality. Additionally, the product quality itself may not be measurable on line, but requires sampling and lab analysis taking several days to be completed. In this study we show that, by using appropriate process analytical technology tools, the operation of an industrial batch bioreactor used in avian vaccine manufacturing can be effectively monitored as the batch progresses. Multivariate statistical models are built from historical databases of batches already completed, and they are used to enable the real time identification of the variability sources, to reliably predict the final product quality, and to improve process understanding, paving the way to a reduction of final product rejections, as well as to a reduction of the product cycle time. It is also shown that the product quality "builds up" mainly during the first half of a batch, suggesting on the one side that reducing the variability during this period is crucial, and on the other side that the batch length can possibly be shortened. Overall, the study demonstrates that, by using a Quality-by-Design approach centered on the appropriate use of mathematical modeling, quality can indeed be built "by design" into the final product, whereas the role of end-point product testing can progressively reduce its importance in product manufacturing. Copyright © 2015 Elsevier B.V. All rights reserved.

A Virtual Sensor for Online Fault Detection of Multitooth-Tools

PubMed Central

Bustillo, Andres; Correa, Maritza; Reñones, Anibal

2011-01-01

The installation of suitable sensors close to the tool tip on milling centres is not possible in industrial environments. It is therefore necessary to design virtual sensors for these machines to perform online fault detection in many industrial tasks. This paper presents a virtual sensor for online fault detection of multitooth tools based on a Bayesian classifier. The device that performs this task applies mathematical models that function in conjunction with physical sensors. Only two experimental variables are collected from the milling centre that performs the machining operations: the electrical power consumption of the feed drive and the time required for machining each workpiece. The task of achieving reliable signals from a milling process is especially complex when multitooth tools are used, because each kind of cutting insert in the milling centre only works on each workpiece during a certain time window. Great effort has gone into designing a robust virtual sensor that can avoid re-calibration due to, e.g., maintenance operations. The virtual sensor developed as a result of this research is successfully validated under real conditions on a milling centre used for the mass production of automobile engine crankshafts. Recognition accuracy, calculated with a k-fold cross validation, had on average 0.957 of true positives and 0.986 of true negatives. Moreover, measured accuracy was 98%, which suggests that the virtual sensor correctly identifies new cases. PMID:22163766

A virtual sensor for online fault detection of multitooth-tools.

PubMed

Bustillo, Andres; Correa, Maritza; Reñones, Anibal

2011-01-01

The installation of suitable sensors close to the tool tip on milling centres is not possible in industrial environments. It is therefore necessary to design virtual sensors for these machines to perform online fault detection in many industrial tasks. This paper presents a virtual sensor for online fault detection of multitooth tools based on a bayesian classifier. The device that performs this task applies mathematical models that function in conjunction with physical sensors. Only two experimental variables are collected from the milling centre that performs the machining operations: the electrical power consumption of the feed drive and the time required for machining each workpiece. The task of achieving reliable signals from a milling process is especially complex when multitooth tools are used, because each kind of cutting insert in the milling centre only works on each workpiece during a certain time window. Great effort has gone into designing a robust virtual sensor that can avoid re-calibration due to, e.g., maintenance operations. The virtual sensor developed as a result of this research is successfully validated under real conditions on a milling centre used for the mass production of automobile engine crankshafts. Recognition accuracy, calculated with a k-fold cross validation, had on average 0.957 of true positives and 0.986 of true negatives. Moreover, measured accuracy was 98%, which suggests that the virtual sensor correctly identifies new cases.

Real-time portable system for fabric defect detection using an ARM processor

NASA Astrophysics Data System (ADS)

Fernandez-Gallego, J. A.; Yañez-Puentes, J. P.; Ortiz-Jaramillo, B.; Alvarez, J.; Orjuela-Vargas, S. A.; Philips, W.

2012-06-01

Modern textile industry seeks to produce textiles as little defective as possible since the presence of defects can decrease the final price of products from 45% to 65%. Automated visual inspection (AVI) systems, based on image analysis, have become an important alternative for replacing traditional inspections methods that involve human tasks. An AVI system gives the advantage of repeatability when implemented within defined constrains, offering more objective and reliable results for particular tasks than human inspection. Costs of automated inspection systems development can be reduced using modular solutions with embedded systems, in which an important advantage is the low energy consumption. Among the possibilities for developing embedded systems, the ARM processor has been explored for acquisition, monitoring and simple signal processing tasks. In a recent approach we have explored the use of the ARM processor for defects detection by implementing the wavelet transform. However, the computation speed of the preprocessing was not yet sufficient for real time applications. In this approach we significantly improve the preprocessing speed of the algorithm, by optimizing matrix operations, such that it is adequate for a real time application. The system was tested for defect detection using different defect types. The paper is focused in giving a detailed description of the basis of the algorithm implementation, such that other algorithms may use of the ARM operations for fast implementations.

76 FR 41657 - Airworthiness Directives; Airbus Model A330-342 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-15

... production. As a result, ALI [Airworthiness Limitation Item] task 533105-01- 02 has not been performed on the... products. The MCAI states: Airworthiness Limitation Item (ALI) task 533105-01-02 is applicable to... embodied in production. As a result, ALI task 533105-01-02 has not been performed on the MSN listed in the...

Mental workload associated with operating an agricultural sprayer: an empirical approach.

PubMed

Dey, A K; Mann, D D

2011-04-01

Agricultural spraying involves two major tasks: guiding a sprayer in response to a GPS navigation device, and simultaneous monitoring of rear-attached booms under various illumination and terrain difficulty levels. The aim of the present study was to investigate the effect of illumination, task difficulty, and task level on the mental workload of an individual operating an agricultural sprayer in response to a commercial GPS lightbar, and to explore the sensitivity of the NASA-TLX and SSWAT subjective rating scales in discriminating the subjective experienced workload under various task, illumination, and difficulty levels. Mental workload was measured using performance measures (lateral root mean square error and reaction time), physiological measures (0.1 Hz power of HRV, latency of the P300 component of event-related potential, and eye-glance behavior), and two subjective rating scales (NASA-TLX and SSWAT). Sixteen male university students participated in this experiment, and a fixed-base high-fidelity agricultural tractor simulator was used to create a simulated spraying task. All performance measures, the P300 latency, and subjective rating scales showed a common trend that mental workload increased with the change in illumination from day to night, with task difficulty from low to high, and with task type from single to dual. The 0.1 Hz power of HRV contradicted the performance measures. Eye-glance data showed that under night illumination, participants spent more time looking at the lightbar for guidance information. A similar trend was observed with the change in task type from single to dual. Both subjective rating scales showed a common trend of increasing mental workload with the change in illumination, difficulty, and task levels. However, the SSWAT scale was more sensitive than the NASA-TLX scale. With the change in illumination, difficulty, and task levels, participants spent more mental resources to meet the increased task demand; hence, the illumination, task difficulty, and task level affected the mental workload of an agricultural sprayer operator operating a sprayer in response to a GPS lightbar.

Using full-mission simulation for human factors research in air transport operations

NASA Technical Reports Server (NTRS)

Orlady, Harry W.; Hennessy, Robert W.; Obermayer, Richard; Vreuls, Donald; Murphy, Miles R.

1988-01-01

This study examined state-of-the-art mission oriented simulation and its use in human factors research. Guidelines were developed for doing full-mission human factors research on crew member behavior during simulated air transport operations. The existing literature was reviewed. However, interviews with experienced investigators provided the most useful information. The fundamental scientific and practical issues of behavioral research in a simulation environment are discussed. Guidelines are presented for planning, scenario development, and the execution of behavioral research using full-mission simulation in the context of air transport flight operations . Research is recommended to enhance the validity and productivity of full-mission research by: (1) validating the need for high-fidelity simulation of all major elements in the operational environment, (2) improving methods for conducting full-mission research, and (3) examining part-task research on specific problems through the use of vehicles which contain higher levels of abstraction (and lower fidelity) of the operational environment.

The determination of effective injury controls for metal-cutting lathe operators.

PubMed

Etherton, J R; Trump, T R; Jensen, R C

1981-01-01

Operators of metal-working lathes are one of the largest manufacturing machine worker populations in the United States. Machines (other than vehicular) account for over 10% of occupational injuries each year. An estimated 3,400 operators of metal-working lathes suffer lost-time injuries annually in the United States. Some of these are fatal. Therefore an investigation was undertaken to determine methods for reducing injuries to lathe operators. Three methods were used: (i) review of injury reports, (ii) human factors analysis, and (iii) fault-tree procedures. The investigation followed the man-machine systems approach of looking for injury-producing dysfunctions between the lathe and the lathe operator. The major sources of injury were found to be chips and workholding devices. Secondary tasks were found to be more hazardous than is generally recognized. The use of three methods for approaching the problem was found to be useful in that injury controls were identified which are likely to be adopted because of their potential for improving safety without adversely affecting productivity.

Computational Virtual Reality (VR) as a human-computer interface in the operation of telerobotic systems

NASA Technical Reports Server (NTRS)

Bejczy, Antal K.

1995-01-01

This presentation focuses on the application of computer graphics or 'virtual reality' (VR) techniques as a human-computer interface tool in the operation of telerobotic systems. VR techniques offer very valuable task realization aids for planning, previewing and predicting robotic actions, operator training, and for visual perception of non-visible events like contact forces in robotic tasks. The utility of computer graphics in telerobotic operation can be significantly enhanced by high-fidelity calibration of virtual reality images to actual TV camera images. This calibration will even permit the creation of artificial (synthetic) views of task scenes for which no TV camera views are available.

Petri nets as a modeling tool for discrete concurrent tasks of the human operator. [describing sequential and parallel demands on human operators

NASA Technical Reports Server (NTRS)

Schumacher, W.; Geiser, G.

1978-01-01

The basic concepts of Petri nets are reviewed as well as their application as the fundamental model of technical systems with concurrent discrete events such as hardware systems and software models of computers. The use of Petri nets is proposed for modeling the human operator dealing with concurrent discrete tasks. Their properties useful in modeling the human operator are discussed and practical examples are given. By means of and experimental investigation of binary concurrent tasks which are presented in a serial manner, the representation of human behavior by Petri nets is demonstrated.

Using machine learning and real-time workload assessment in a high-fidelity UAV simulation environment

NASA Astrophysics Data System (ADS)

Monfort, Samuel S.; Sibley, Ciara M.; Coyne, Joseph T.

2016-05-01

Future unmanned vehicle operations will see more responsibilities distributed among fewer pilots. Current systems typically involve a small team of operators maintaining control over a single aerial platform, but this arrangement results in a suboptimal configuration of operator resources to system demands. Rather than devoting the full-time attention of several operators to a single UAV, the goal should be to distribute the attention of several operators across several UAVs as needed. Under a distributed-responsibility system, operator task load would be continuously monitored, with new tasks assigned based on system needs and operator capabilities. The current paper sought to identify a set of metrics that could be used to assess workload unobtrusively and in near real-time to inform a dynamic tasking algorithm. To this end, we put 20 participants through a variable-difficulty multiple UAV management simulation. We identified a subset of candidate metrics from a larger pool of pupillary and behavioral measures. We then used these metrics as features in a machine learning algorithm to predict workload condition every 60 seconds. This procedure produced an overall classification accuracy of 78%. An automated tasker sensitive to fluctuations in operator workload could be used to efficiently delegate tasks for teams of UAV operators.

The Copernicus S5P Mission Performance Centre / Validation Data Analysis Facility for TROPOMI operational atmospheric data products

NASA Astrophysics Data System (ADS)

Compernolle, Steven; Lambert, Jean-Christopher; Langerock, Bavo; Granville, José; Hubert, Daan; Keppens, Arno; Rasson, Olivier; De Mazière, Martine; Fjæraa, Ann Mari; Niemeijer, Sander

2017-04-01

Sentinel-5 Precursor (S5P), to be launched in 2017 as the first atmospheric composition satellite of the Copernicus programme, carries as payload the TROPOspheric Monitoring Instrument (TROPOMI) developed by The Netherlands in close cooperation with ESA. Designed to measure Earth radiance and solar irradiance in the ultraviolet, visible and near infrared, TROPOMI will provide Copernicus with observational data on atmospheric composition at unprecedented geographical resolution. The S5P Mission Performance Center (MPC) provides an operational service-based solution for various QA/QC tasks, including the validation of S5P Level-2 data products and the support to algorithm evolution. Those two tasks are to be accomplished by the MPC Validation Data Analysis Facility (VDAF), one MPC component developed and operated at BIRA-IASB with support from S[&]T and NILU. The routine validation to be ensured by VDAF is complemented by a list of validation AO projects carried out by ESA's S5P Validation Team (S5PVT), with whom interaction is essential. Here we will introduce the general architecture of VDAF, its relation to the other MPC components, the generic and specific validation strategies applied for each of the official TROPOMI data products, and the expected output of the system. The S5P data products to be validated by VDAF are diverse: O3 (vertical profile, total column, tropospheric column), NO2 (total and tropospheric column), HCHO (tropospheric column), SO2 (column), CO (column), CH4 (column), aerosol layer height and clouds (fractional cover, cloud-top pressure and optical thickness). Starting from a generic validation protocol meeting community-agreed standards, a set of specific validation settings is associated with each data product, as well as the appropriate set of Fiducial Reference Measurements (FRM) to which it will be compared. VDAF collects FRMs from ESA's Validation Data Centre (EVDC) and from other sources (e.g., WMO's GAW, NDACC and TCCON). Data manipulations on satellite and FRM data (format conversion, filtering, co-location, regridding and vertical smoothing) are performed by the open source software HARP, while more specific manipulations apply in-house routines. The paper concludes with a short description of expected outputs of the system.

75 FR 16696 - Airworthiness Directives; Airbus Model A330-223, -321, -322, and -323 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-02

... Damage Tolerant--Airworthiness Limitation Item task 712106-01-01 from A330 ALS Part 2, an A330 operator...: During accomplishment of Damage Tolerant--Airworthiness Limitation Item task 712106-01-01 from A330 ALS... Tolerant--Airworthiness Limitation Item task 712106-01-01 from A330 ALS Part 2, an A330 operator found a...

Land Ahoy! Understanding Submarine Command and Control During the Completion of Inshore Operations.

PubMed

Roberts, Aaron P J; Stanton, Neville A; Fay, Daniel

2017-12-01

The aim of this study was to use multiple command teams to provide empirical evidence for understanding communication flow, information pertinence, and tasks undertaken in a submarine control room when completing higher- and lower-demand inshore operation (INSO) scenarios. The focus of submarine operations has changed, and submarines are increasingly required to operate in costal littoral zones. However, submarine command team performance during INSO is not well understood, particularly from a sociotechnical systems perspective. A submarine control-room simulator was built. The creation of networked workstations allowed a team of nine operators to perform tasks completed by submarine command teams during INSO. The Event Analysis of Systematic Teamwork method was used to model the social, task, and information networks and to describe command team performance. Ten teams were recruited for the study, affording statistical comparisons of how command-team roles and level of demand affected performance. Results indicated that the submarine command-team members are required to rapidly integrate sonar and visual data as the periscope is used, periodically, in a "duck-and-run" fashion, to maintain covertness. The fusion of such information is primarily completed by the operations officer (OPSO), with this operator experiencing significantly greater demand than any other operator. The OPSO was a bottleneck in the command team when completing INSO, experiencing similar load in both scenarios, suggesting that the command team may benefit from data synthesis tasks being more evenly distributed within the command team. The work can inform future control-room design and command-team ways of working by identifying bottlenecks in terms of information and task flow between operators.

Pirate Stealth or Inattentional Blindness? The Effects of Target Relevance and Sustained Attention on Security Monitoring for Experienced and Naïve Operators

PubMed Central

Näsholm, Erika; Rohlfing, Sarah; Sauer, James D.

2014-01-01

Closed Circuit Television (CCTV) operators are responsible for maintaining security in various applied settings. However, research has largely ignored human factors that may contribute to CCTV operator error. One important source of error is inattentional blindness – the failure to detect unexpected but clearly visible stimuli when attending to a scene. We compared inattentional blindness rates for experienced (84 infantry personnel) and naïve (87 civilians) operators in a CCTV monitoring task. The task-relevance of the unexpected stimulus and the length of the monitoring period were manipulated between participants. Inattentional blindness rates were measured using typical post-event questionnaires, and participants' real-time descriptions of the monitored event. Based on the post-event measure, 66% of the participants failed to detect salient, ongoing stimuli appearing in the spatial field of their attentional focus. The unexpected task-irrelevant stimulus was significantly more likely to go undetected (79%) than the unexpected task-relevant stimulus (55%). Prior task experience did not inoculate operators against inattentional blindness effects. Participants' real-time descriptions revealed similar patterns, ruling out inattentional amnesia accounts. PMID:24465932

The effect of workstation and task variables on forces applied during simulated meat cutting.

PubMed

McGorry, Raymond W; Dempsey, Patrick G; O'Brien, Niall V

2004-12-01

The purpose of the study was to investigate factors related to force and postural exposure during a simulated meat cutting task. The hypothesis was that workstation, tool and task variables would affect the dependent kinetic variables of gripping force, cutting moment and the dependent kinematic variables of elbow elevation and wrist angular displacement in the flexion/extension and radial/ulnar deviation planes. To evaluate this hypothesis a 3 x 3 x 2 x 2 x 2 (surface orientation by surface height by blade angle by cut complexity by work pace) within-subject factorial design was conducted with 12 participants. The results indicated that the variables can act and interact to modify the kinematics and kinetics of a cutting task. Participants used greater grip force and cutting moment when working at a pace based on productivity. The interactions of the work surface height and orientation indicated that the use of an adjustable workstation could minimize wrist deviation from neutral and improve shoulder posture during cutting operations. Angling the knife blade also interacted with workstation variables to improve wrist and upper extremity posture, but this benefit must be weighed against the potential for small increases in force exposure.

Exploring Operational Test and Evaluation of Unmanned Aircraft Systems: A Qualitative Case Study

NASA Astrophysics Data System (ADS)

Saliceti, Jose A.

The purpose of this qualitative case study was to explore and identify strategies that may potentially remedy operational test and evaluation procedures used to evaluate Unmanned Aircraft Systems (UAS) technology. The sample for analysis consisted of organizations testing and evaluating UASs (e.g., U.S. Air Force, U.S. Navy, U.S. Army, U.S. Marine Corps, U.S. Coast Guard, and Customs Border Protection). A purposeful sampling technique was used to select 15 subject matter experts in the field of operational test and evaluation of UASs. A questionnaire was provided to participants to construct a descriptive and robust research. Analysis of responses revealed themes related to each research question. Findings revealed operational testers utilized requirements documents to extrapolate measures for testing UAS technology and develop critical operational issues. The requirements documents were (a) developed without the contribution of stakeholders and operational testers, (b) developed with vague or unrealistic measures, and (c) developed without a systematic method to derive requirements from mission tasks. Four approaches are recommended to develop testable operational requirements and assist operational testers: (a) use a mission task analysis tool to derive requirements for mission essential tasks for the system, (b) exercise collaboration among stakeholders and testers to ensure testable operational requirements based on mission tasks, (c) ensure testable measures are used in requirements documents, and (d) create a repository list of critical operational issues by mission areas. The preparation of operational test and evaluation processes for UAS technology is not uniform across testers. The processes in place are not standardized, thus test plan preparation and reporting are different among participants. A standard method to prepare and report UAS technology should be used when preparing and reporting on UAS technology. Using a systematic process, such as mission-based test design, resonated among participants as an analytical method to link UAS mission tasks and measures of performance to the capabilities of the system under test when developing operational test plans. Further research should examine system engineering designs for system requirements traceability matrix of mission tasks and subtasks while using an analysis tool that adequately evaluates UASs with an acceptable level of confidence in the results.

Robotic assembly and maintenance of future space stations based on the ISS mission operations experience

NASA Astrophysics Data System (ADS)

Rembala, Richard; Ower, Cameron

2009-10-01

MDA has provided 25 years of real-time engineering support to Shuttle (Canadarm) and ISS (Canadarm2) robotic operations beginning with the second shuttle flight STS-2 in 1981. In this capacity, our engineering support teams have become familiar with the evolution of mission planning and flight support practices for robotic assembly and support operations at mission control. This paper presents observations on existing practices and ideas to achieve reduced operational overhead to present programs. It also identifies areas where robotic assembly and maintenance of future space stations and space-based facilities could be accomplished more effectively and efficiently. Specifically, our experience shows that past and current space Shuttle and ISS assembly and maintenance operations have used the approach of extensive preflight mission planning and training to prepare the flight crews for the entire mission. This has been driven by the overall communication latency between the earth and remote location of the space station/vehicle as well as the lack of consistent robotic and interface standards. While the early Shuttle and ISS architectures included robotics, their eventual benefits on the overall assembly and maintenance operations could have been greater through incorporating them as a major design driver from the beginning of the system design. Lessons learned from the ISS highlight the potential benefits of real-time health monitoring systems, consistent standards for robotic interfaces and procedures and automated script-driven ground control in future space station assembly and logistics architectures. In addition, advances in computer vision systems and remote operation, supervised autonomous command and control systems offer the potential to adjust the balance between assembly and maintenance tasks performed using extra vehicular activity (EVA), extra vehicular robotics (EVR) and EVR controlled from the ground, offloading the EVA astronaut and even the robotic operator on-orbit of some of the more routine tasks. Overall these proposed approaches when used effectively offer the potential to drive down operations overhead and allow more efficient and productive robotic operations.

Multi-Attribute Task Battery - Applications in pilot workload and strategic behavior research

NASA Technical Reports Server (NTRS)

Arnegard, Ruth J.; Comstock, J. R., Jr.

1991-01-01

The Multi-Attribute Task (MAT) Battery provides a benchmark set of tasks for use in a wide range of lab studies of operator performance and workload. The battery incorporates tasks analogous to activities that aircraft crewmembers perform in flight, while providing a high degree of experimenter control, performance data on each subtask, and freedom to nonpilot test subjects. Features not found in existing computer based tasks include an auditory communication task (to simulate Air Traffic Control communication), a resource management task permitting many avenues or strategies of maintaining target performance, a scheduling window which gives the operator information about future task demands, and the option of manual or automated control of tasks. Performance data are generated for each subtask. In addition, the task battery may be paused and onscreen workload rating scales presented to the subject. The MAT Battery requires a desktop computer with color graphics. The communication task requires a serial link to a second desktop computer with a voice synthesizer or digitizer card.

Man-machine cooperation in advanced teleoperation

NASA Technical Reports Server (NTRS)

Fiorini, Paolo; Das, Hari; Lee, Sukhan

1993-01-01

Teleoperation experiments at JPL have shown that advanced features in a telerobotic system are a necessary condition for good results, but that they are not sufficient to assure consistently good performance by the operators. Two or three operators are normally used during training and experiments to maintain the desired performance. An alternative to this multi-operator control station is a man-machine interface embedding computer programs that can perform some of the operator's functions. In this paper we present our first experiments with these concepts, in which we focused on the areas of real-time task monitoring and interactive path planning. In the first case, when performing a known task, the operator has an automatic aid for setting control parameters and camera views. In the second case, an interactive path planner will rank different path alternatives so that the operator will make the correct control decision. The monitoring function has been implemented with a neural network doing the real-time task segmentation. The interactive path planner was implemented for redundant manipulators to specify arm configurations across the desired path and satisfy geometric, task, and performance constraints.

Advanced helicopter cockpit and control configurations for helicopter combat missions

NASA Technical Reports Server (NTRS)

Haworth, Loran A.; Atencio, Adolph, Jr.; Bivens, Courtland; Shively, Robert; Delgado, Daniel

1987-01-01

Two piloted simulations were conducted by the U.S. Army Aeroflightdynamics Directorate to evaluate workload and helicopter-handling qualities requirements for single pilot operation in a combat Nap-of-the-Earth environment. The single-pilot advanced cockpit engineering simulation (SPACES) investigations were performed on the NASA Ames Vertical Motion Simulator, using the Advanced Digital Optical Control System control laws and an advanced concepts glass cockpit. The first simulation (SPACES I) compared single pilot to dual crewmember operation for the same flight tasks to determine differences between dual and single ratings, and to discover which control laws enabled adequate single-pilot helicopter operation. The SPACES II simulation concentrated on single-pilot operations and use of control laws thought to be viable candidates for single pilot operations workload. Measures detected significant differences between single-pilot task segments. Control system configurations were task dependent, demonstrating a need for inflight reconfigurable control system to match the optimal control system with the required task.

Korean College EFL Learners' Task Motivation in Written Language Production

ERIC Educational Resources Information Center

Kim, Bomin; Kim, Haedong

2016-01-01

The aims of the present study were to explore the effects of two different types of task conditions (topic choice vs. no choice) on the quality of written production in a second language (lexical complexity, syntactic complexity, and cohesion) and to investigate the effects of these two different task conditions on task motivation. This research…

Comparative Cognitive Task Analysis

DTIC Science & Technology

2007-01-01

is to perform a task analyses to determine how people operate in a specific domain on a specific task. Cognitive Task Analysis (CTA) is a set of...accomplish a task. In this chapter, we build on CTA methods by suggesting that comparative cognitive task analysis (C2TA) can help solve the aforementioned

Acute effects of caffeine on several operant behaviors in rhesus monkeys.

PubMed

Buffalo, E A; Gillam, M P; Allen, R R; Paule, M G

1993-11-01

The acute effects of 1,3-trimethylxanthine (caffeine) were assessed using an operant test battery (OTB) of complex food-reinforced tasks that are thought to depend upon relatively specific brain functions, such as motivation to work for food (progressive ratio, PR), learning (incremental repeated acquisition, IRA), color and position discrimination (conditioned position responding, CPR), time estimation (temporal response differentiation, TRD), and short-term memory and attention (delayed matching-to-sample, DMTS). Endpoints included response rates (RR), accuracies (ACC), and percent task completed (PTC). Caffeine sulfate (0.175-20.0 mg/kg, IV), given 15 min pretesting, produced significant dose-dependent decreases in TRD percent task completed and accuracy at doses > or = 5.6 mg/kg. Caffeine produced no systematic effects on either DMTS or PR responding, but low doses tended to enhance performance in both IRA and CPR tasks. Thus, in monkeys, performance of an operant task designed to model time estimation is more sensitive to the disruptive effects of caffeine than is performance of the other tasks in the OTB.

Specificity and transfer effects in time production skill: examining the role of attention.

PubMed

Wohldmann, Erica L; Healy, Alice F; Bourne, Lyle E

2012-05-01

Two experiments examined transfer of a prospective, time production skill under conditions involving changes in concurrent task requirements. Positive transfer of the time production skill might be expected only when the attentional demands of the concurrent task were held constant from training to test. However, some positive transfer was found even when the concurrent task at retraining was made either easier or more difficult than the concurrent task learned during training. The amount and direction of transfer depended more on the pacing of the stimuli in the secondary task than on the difficulty of the secondary task, even though difficulty affects attentional demands more. These findings are consistent with the procedural reinstatement principle of skill learning, by which transfer from one task to another depends on an overlap in procedures required by the two skills.

A Correlational Study of Seven Projective Spatial Structures with Regard to the Phases of the MOON^

NASA Astrophysics Data System (ADS)

Wellner, Karen Linette

1995-01-01

This study investigated the relationship between projective spatial structures and the ability to construct a scientific model. In addition, gender-related performance and the influence of prior astronomy experience on task success were evaluated. Sixty-one college science undergraduates were individually administered Piagetian tasks to assess for projective spatial structures and the ability to set up a phases of the moon model. The spatial tasks included: (a) Mountains task (coordination of perspectives); (b) Railroad task (size and intervals of objects with increasing distance); (c) Telephone Poles task (masking and ordering objects); and (d) Shadows task (spatial relationships between an object and its shadow, dependent upon the object's orientation). Cramer coefficient analyses indicated that significant relationships existed between Moon task and spatial task success. In particular, the Shadows task, requiring subjects to draw shadows of objects in different orientations, proved most difficult and was most strongly associated with with a subject's understanding of lunar phases. Chi-square tests for two independent samples were used to analyze gender performance differences on each of the Ave tasks. Males performed significantly better at a.05 significance level in regard to the Shadows task and the Moon task. Chi-square tests for two independent samples showed no significant difference in Moon task performance between subjects with astronomy or Earth science coursework, and those without such science classroom experience. Overall, only six subjects passed all seven projective spatial structure tasks. Piaget (1967) contends that concrete -operational spatial structures must be established before an individual is able to develop formal-operational patterns of thinking. The results of this study indicate that 90% of the interviewed science majors are still operating at the concrete-operational level. Several educational implications were drawn from this study: (1) The teaching of spatially dependent content to students without prerequisite spatial structures results in understanding no further beyond that which can be memorized; (2) assessment for projective spatial structures should precede science lessons dealing with time-space relationships, and (3) a student's level of spatial ability may directly impact upon interpretation of three-dimensional models.

How smart is your BEOL? productivity improvement through intelligent automation

NASA Astrophysics Data System (ADS)

Schulz, Kristian; Egodage, Kokila; Tabbone, Gilles; Garetto, Anthony

2017-07-01

The back end of line (BEOL) workflow in the mask shop still has crucial issues throughout all standard steps which are inspection, disposition, photomask repair and verification of repair success. All involved tools are typically run by highly trained operators or engineers who setup jobs and recipes, execute tasks, analyze data and make decisions based on the results. No matter how experienced operators are and how good the systems perform, there is one aspect that always limits the productivity and effectiveness of the operation: the human aspect. Human errors can range from seemingly rather harmless slip-ups to mistakes with serious and direct economic impact including mask rejects, customer returns and line stops in the wafer fab. Even with the introduction of quality control mechanisms that help to reduce these critical but unavoidable faults, they can never be completely eliminated. Therefore the mask shop BEOL cannot run in the most efficient manner as unnecessary time and money are spent on processes that still remain labor intensive. The best way to address this issue is to automate critical segments of the workflow that are prone to human errors. In fact, manufacturing errors can occur for each BEOL step where operators intervene. These processes comprise of image evaluation, setting up tool recipes, data handling and all other tedious but required steps. With the help of smart solutions, operators can work more efficiently and dedicate their time to less mundane tasks. Smart solutions connect tools, taking over the data handling and analysis typically performed by operators and engineers. These solutions not only eliminate the human error factor in the manufacturing process but can provide benefits in terms of shorter cycle times, reduced bottlenecks and prediction of an optimized workflow. In addition such software solutions consist of building blocks that seamlessly integrate applications and allow the customers to use tailored solutions. To accommodate for the variability and complexity in mask shops today, individual workflows can be supported according to the needs of any particular manufacturing line with respect to necessary measurement and production steps. At the same time the efficiency of assets is increased by avoiding unneeded cycle time and waste of resources due to the presence of process steps that are very crucial for a given technology. In this paper we present details of which areas of the BEOL can benefit most from intelligent automation, what solutions exist and the quantification of benefits to a mask shop with full automation by the use of a back end of line model.

Operator strategies under varying conditions of workload

NASA Technical Reports Server (NTRS)

Arnegard, Ruth J.

1991-01-01

An attempt was made to operationally define and measure strategic behavior in a complex multiple task environment. The Multi-Attribute Task battery was developed to simulate various aspects of flight and consisted of an auditory communication task, monitoring tasks, a tracking tasks, a resource management task which allowed a wide range of responding patterns, and a scheduling window which allowed operators to predict changes in workload. This battery was validated for its sensitivity to strategic behavior, and baseline measures for each individual task were collected. Twenty-four undergraduate and graduate students then performed the battery for four 64 minute sessions which took place over a period of 2 days. Each subject performed the task battery under four levels of workload, which were presented for equal lengths of time during all four sessions. Results indicated that in general, performance improves as a function of experience with the battery, but that performance decreased as workload level increased. The data also showed that subjects developed strategies for responding to the resource management task which allowed them to manage the high workload levels more efficiently. This particular strategy developed over time but was also associated with errors of complacency. These results are presented along with implications for the aviation field and areas of future research.

AMU NEXRAD Exploitation Task

NASA Technical Reports Server (NTRS)

Lambert, Winifred C.; Wheeler, Mark M.

1997-01-01

This report documents the results of the Applied Meteorology Unit's NEXRAD Exploitation Task. The objectives of this task are to determine what radar signatures are present prior to and at the time of convection initiation, and to determine radar signatures which will help distinguish whether the ensuing convection will become severe. Radar data from the WSR-88D radar located at NWS Melbourne (WSR-88D/KMLB) were collected between June and September 1995, and 16 convective case studies were analyzed for which the radar was operating during the entire period of interest. All WSR-88D/KMLB products were scrutinized for their utility in detecting convection initiation and severe storm signatures. Through process of elimination, it was found that the 0.5 deg reflectivity product with the lowest reflectivity values displayed is the best product to monitor for convection initiation signatures. Seven meteorological features associated with the initiation of deep convection were identified: the Merritt Island and Indian River convergence zones, interlake convergence, horizontal convective rolls, the sea breeze, storm outflow boundaries, and fires. Their reflectivity values ranged from -5 to 20 dBZ. Of the three severe weather phenomena (winds greater than or equal to 50 kts, tornado, 3/4 inch hail), high wind events due to microbursts were most common in the data set. It was found that the values and trends of composite reflectivity, vertically integrated liquid, and core aspect ratio were key indicators of the potential of a cell to produce a microburst. The data were not analyzed for the other two severe weather phenomena because they rarely occurred during the data collection period. This report also includes suggestions for new WSR-88D products, summaries of ongoing research aimed at creating new products, and explicit recommended procedures for detecting convection initiation and severe storm signatures in the radar data using the currently available technology.

Determinants explaining the variability of hand-transmitted vibration emissions from two different work tasks: grinding and cutting using angle grinders.

PubMed

Liljelind, Ingrid; Pettersson, Hans; Nilsson, Leif; Wahlström, Jens; Toomingas, Allan; Lundström, Ronnie; Burström, Lage

2013-10-01

There are numerous factors including physical, biomechanical, and individual that influence exposure to hand-transmitted vibration (HTV) and cause variability in the exposure measurements. Knowledge of exposure variability and determinants of exposure could be used to improve working conditions. We performed a quasi-experimental study, where operators performed routine work tasks in order to obtain estimates of the variance components and to evaluate the effect of determinants, such as machine-wheel combinations and individual operator characteristics. Two pre-defined simulated work tasks were performed by 11 operators: removal of a weld puddle of mild steel and cutting of a square steel pipe. In both tasks, four angle grinders were used, two running on compressed air and two electrically driven. Two brands of both grinding and cutting wheels were used. Each operator performed both tasks twice in a random order with each grinder and wheel and the time to complete each task was recorded. Vibration emission values were collected and the wheel wear was measured as loss of weight. Operators' characteristics collected were as follows: age, body height and weight, length and volume of their hands, maximum hand grip force, and length of work experience with grinding machines (years). The tasks were also performed by one operator who used four machines of the same brand. Mixed and random effects models were used in the statistical evaluation. The statistical evaluation was performed for grinding and cutting separately and we used a measure referring to the sum of the 1-s r.m.s. average frequency-weighted acceleration over time for completing the work task (a(sa)). Within each work task, there was a significant effect as a result of the determinants 'the machine used', 'wheel wear', and 'time taken to complete the task'. For cutting, 'the brand of wheel' used also had a significant effect. More than 90% of the inherent variability in the data was explained by the determinants. The two electrically powered machines had a mean a(sa) that was 2.6 times higher than the two air-driven machines. For cutting, the effect of the brand of wheel on a(sa) was ~0.1 times. The a(sa) increased both with increasing wheel wear and with time taken to complete the work task. However, there were also a number of interaction effects which, to a minor extent, modified the a(sa). Only a minor part (1%) of the total variability was attributed to the operator: for cutting, the volume of the hands, maximum grip force, and body weight were significant, while for grinding, it was the maximum grip force. There was no clear difference in a(sa) between the four copies of the same brand of each machine. By including determinants that were attributed to the brand of both machine and wheel used as well as the time taken to complete the work task, we were able to explain >90% of the variability. The dominating determinant was the brand of the machine. Little variability was found between operators, indicating that the overall effect as due to the operator was small.

Process improvement of knives production in a small scale industry

NASA Astrophysics Data System (ADS)

Ananto, Gamawan; Muktasim, Irfan

2017-06-01

Small scale industry that produces several kinds of knive should increase its capacity due to the demand from the market. Qualitatively, this case study consisted of formulating the problems, collecting and analyzing the necessary data, and determining the possible recommendations for the improvement. While the current capacity is only 9 (nine), it is expected that 20 units of knife will produced per month. The processes sequence are: profiling (a), truing (b), beveling (c), heat treatment (d), polishing (e), assembly (f), sharpening (g) and finishing (h). The first process (a) is held by out-house vendor company while other steps from (b) to (g) are executed by in-house vendor. However, there is a high dependency upon the high skilled operator who executes the in -house processes that are mostly held manually with several unbalance successive tasks, where the processing time of one or two tasks require longer duration than others since the operation is merely relied on the operator's skill. The idea is the improvement or change of the profiling and beveling process. Due to the poor surface quality and suboptimal hardness resulted from the laser cut machine for profiling, it is considered to subst itute this kind of process with wire cut that is capable to obtain good surface quality with certain range levels of roughness. Through simple cutting experiments on the samples, it is expected that the generated surface quality is adequate to omit the truing process (b). In addition, the cutting experiments on one, two, and four test samples resulted the shortest time that was obtained through four pieces in one cut. The technical parameters were set according to the recommendation of machine standard as referred to samples condition such as thickness and path length that affect ed the rate of wear. Meanwhile, in order to guarantee the uniformity of knife angles that are formed through beveling process (c), a grinding fixture was created. This kind of tool diminishes the dependency upon the operator's skill as well. The main conclusions are: the substitution of laser cut with wire cut machine for the first task (a) could reduce the operation time from 60 to 39.26 minutes with good result of surface quality and the truing process (b) could be omitted; the additional grinding fixture in beveling process (c) is required and two workstations have to be assigned instead of one as in previous condition. They lead to improvements including the guarantee of the uniformity of knifes' angle, the reduction on the operators' skills dependency, the shortening of cycle time from 855 to 420 minutes, and the higher number of productivity from 9 units/month into 20units/month.

Electrophysiologically dissociating episodic preretrieval processing.

PubMed

Bridger, Emma K; Mecklinger, Axel

2012-06-01

Contrasts between ERPs elicited by new items from tests with distinct episodic retrieval requirements index preretrieval processing. Preretrieval operations are thought to facilitate the recovery of task-relevant information because they have been shown to correlate with response accuracy in tasks in which prioritizing the retrieval of this information could be a useful strategy. This claim was tested here by contrasting new item ERPs from two retrieval tasks, each designed to explicitly require the recovery of a different kind of mnemonic information. New item ERPs differed from 400 msec poststimulus, but the distribution of these effects varied markedly, depending upon participants' response accuracy: A protracted posteriorly located effect was present for higher performing participants, whereas an anteriorly distributed effect occurred for lower performing participants. The magnitude of the posterior effect from 400 to 800 msec correlated with response accuracy, supporting the claim that preretrieval processes facilitate the recovery of task-relevant information. Additional contrasts between ERPs from these tasks and an old/new recognition task operating as a relative baseline revealed task-specific effects with nonoverlapping scalp topographies, in line with the assumption that these new item ERP effects reflect qualitatively distinct retrieval operations. Similarities in these effects were also used to reason about preretrieval processes related to the general requirement to recover contextual details. These insights, alongside the distinct pattern of effects for the two accuracy groups, reveal the multifarious nature of preretrieval processing while indicating that only some of these classes of operation are systematically related to response accuracy in recognition memory tasks.

Application of the airborne ocean color imager for commercial fishing

NASA Technical Reports Server (NTRS)

Wrigley, Robert C.

1993-01-01

The objective of the investigation was to develop a commercial remote sensing system for providing near-real-time data (within one day) in support of commercial fishing operations. The Airborne Ocean Color Imager (AOCI) had been built for NASA by Daedalus Enterprises, Inc., but it needed certain improvements, data processing software, and a delivery system to make it into a commercial system for fisheries. Two products were developed to support this effort: the AOCI with its associated processing system and an information service for both commercial and recreational fisheries to be created by Spectro Scan, Inc. The investigation achieved all technical objectives: improving the AOCI, creating software for atmospheric correction and bio-optical output products, georeferencing the output products, and creating a delivery system to get those products into the hands of commercial and recreational fishermen in near-real-time. The first set of business objectives involved Daedalus Enterprises and also were achieved: they have an improved AOCI and new data processing software with a set of example data products for fisheries applications to show their customers. Daedalus' marketing activities showed the need for simplification of the product for fisheries, but they successfully marketed the current version to an Italian consortium. The second set of business objectives tasked Spectro Scan to provide an information service and they could not be achieved because Spectro Scan was unable to obtain necessary venture capital to start up operations.

Task Analysis for the Jobs of Freight Train Conductor and Brakeman. RDTR No. 263.

ERIC Educational Resources Information Center

Sanders, Mark S.; And Others

The principal tasks performed by conductors, rear brakemen, and head brakemen during over-the-road freight operations are identified and described in the report. Forty-four tasks and subtasks are analyzed and grouped into six categories: basic handling tasks, prerun preparation and starting off tasks, over-the-road tasks, terminating tasks,…

A Task Analytic Process to Define Future Concepts in Aviation

NASA Technical Reports Server (NTRS)

Gore, Brian Francis; Wolter, Cynthia A.

2014-01-01

A necessary step when developing next generation systems is to understand the tasks that operators will perform. One NextGen concept under evaluation termed Single Pilot Operations (SPO) is designed to improve the efficiency of airline operations. One SPO concept includes a Pilot on Board (PoB), a Ground Station Operator (GSO), and automation. A number of procedural changes are likely to result when such changes in roles and responsibilities are undertaken. Automation is expected to relieve the PoB and GSO of some tasks (e.g. radio frequency changes, loading expected arrival information). A major difference in the SPO environment is the shift to communication-cued crosschecks (verbal / automated) rather than movement-cued crosschecks that occur in a shared cockpit. The current article highlights a task analytic process of the roles and responsibilities between a PoB, an approach-phase GSO, and automation.

Analysis of remote operating systems for space-based servicing operations. Volume 2: Study results

NASA Technical Reports Server (NTRS)

1985-01-01

The developments in automation and robotics have increased the importance of applications for space based servicing using remotely operated systems. A study on three basic remote operating systems (teleoperation, telepresence and robotics) was performed in two phases. In phase one, requirements development, which consisted of one three-month task, a group of ten missions were selected. These included the servicing of user equipment on the station and the servicing of the station itself. In phase two, concepts development, which consisted of three tasks, overall system concepts were developed for the selected missions. These concepts, which include worksite servicing equipment, a carrier system, and payload handling equipment, were evaluated relative to the configurations of the overall worksite. It is found that the robotic/teleoperator concepts are appropriate for relatively simple structured tasks, while the telepresence/teleoperator concepts are applicable for missions that are complex, unstructured tasks.

Endpoint-based parallel data processing in a parallel active messaging interface of a parallel computer

DOEpatents

Archer, Charles J.; Blocksome, Michael A.; Ratterman, Joseph D.; Smith, Brian E.

2014-08-12

Endpoint-based parallel data processing in a parallel active messaging interface (`PAMI`) of a parallel computer, the PAMI composed of data communications endpoints, each endpoint including a specification of data communications parameters for a thread of execution on a compute node, including specifications of a client, a context, and a task, the compute nodes coupled for data communications through the PAMI, including establishing a data communications geometry, the geometry specifying, for tasks representing processes of execution of the parallel application, a set of endpoints that are used in collective operations of the PAMI including a plurality of endpoints for one of the tasks; receiving in endpoints of the geometry an instruction for a collective operation; and executing the instruction for a collective operation through the endpoints in dependence upon the geometry, including dividing data communications operations among the plurality of endpoints for one of the tasks.

The planetary water drama: Dual task of feeding humanity and curbing climate change

NASA Astrophysics Data System (ADS)

Rockström, J.; Falkenmark, M.; Lannerstad, M.; Karlberg, L.

2012-08-01

This paper analyses the potential conflict between resilience of the Earth system and global freshwater requirements for the dual task of carbon sequestration to reduce CO2 in the atmosphere, and food production to feed humanity by 2050. It makes an attempt to assess the order of magnitude of the increased consumptive water use involved and analyses the implications as seen from two parallel perspectives; the global perspective of human development within a “safe operating space” with regard to the definition of the Planetary Boundary for freshwater; and the social-ecological implications at the regional river basin scale in terms of sharpening water shortages and threats to aquatic ecosystems. The paper shows that the consumptive water use involved in the dual task would both transgress the proposed planetary boundary range for global consumptive freshwater use and would further exacerbate already severe river depletion, causing societal problems related to water shortage and water allocation. Thus, strategies to rely on sequestration of CO2 as a mitigation strategy must recognize the high freshwater costs involved, implying that the key climate mitigation strategy must be to reduce emissions. The paper finally highlights the need to analyze both water and carbon tradeoffs from anticipated large scale biofuel production climate change mitigation strategy, to reveal gains and impact of this in contrast to carbon sequestration strategies.

Modeling Operator Performance in Low Task Load Supervisory Domains

DTIC Science & Technology

2011-06-01

PDF Probability Distribution Function SAFE System for Aircrew Fatigue Evaluation SAFTE Sleep , Activity, Fatigue, and Task Effectiveness SCT...attentional capacity due to high mental workload. In low task load settings, fatigue is mainly caused by lack of sleep and boredom experienced by...performance decrements. Also, psychological fatigue is strongly correlated with lack of sleep . Not surprisingly, operators of the morning shift reported the

The Impact of Human-Automation Collaboration in Decentralized Multiple Unmanned Vehicle Control

DTIC Science & Technology

2011-01-01

based decentralized auctions for robust task allocation ,[ IEEE Trans. Robot., vol. 25, no. 4, pp...operators can aid such systems by bringing their knowledge- based reasoning and experience to bear. Given a decentralized task planner and a goal- based ...experience to bear. Given a decentralized task planner and a goal- based operator interface for a network of unmanned vehicles in a search, track,

Space station operations task force. Panel 4 report: Management integration

NASA Technical Reports Server (NTRS)

1987-01-01

The Management Integration Panel of the Space Station Operations Task Force was chartered to provide a structure and ground rules for integrating the efforts of the other three panels and to address a number of cross cutting issues that affect all areas of space station operations. Issues addressed include operations concept implementation, alternatives development and integration process, strategic policy issues and options, and program management emphasis areas.

Definition of technology development missions for early space stations orbit transfer vehicle serving. Phase 2, task 1: Space station support of operational OTV servicing

NASA Technical Reports Server (NTRS)

1983-01-01

Representative space based orbital transfer vehicles (OTV), ground based vehicle turnaround assessment, functional operational requirements and facilities, mission turnaround operations, a comparison of ground based versus space based tasks, activation of servicing facilities prior to IOC, fleet operations requirements, maintenance facilities, OTV servicing facilities, space station support requirements, and packaging for delivery are discussed.

Experiences with the ALICE Mesos infrastructure

NASA Astrophysics Data System (ADS)

Berzano, D.; Eulisse, G.; Grigoraş, C.; Napoli, K.

2017-10-01

Apache Mesos is a resource management system for large data centres, initially developed by UC Berkeley, and now maintained under the Apache Foundation umbrella. It is widely used in the industry by companies like Apple, Twitter, and Airbnb and it is known to scale to 10 000s of nodes. Together with other tools of its ecosystem, such as Mesosphere Marathon or Metronome, it provides an end-to-end solution for datacenter operations and a unified way to exploit large distributed systems. We present the experience of the ALICE Experiment Offline & Computing in deploying and using in production the Apache Mesos ecosystem for a variety of tasks on a small 500 cores cluster, using hybrid OpenStack and bare metal resources. We will initially introduce the architecture of our setup and its operation, we will then describe the tasks which are performed by it, including release building and QA, release validation, and simple Monte Carlo production. We will show how we developed Mesos enabled components (called “Mesos Frameworks”) to carry out ALICE specific needs. In particular, we will illustrate our effort to integrate Work Queue, a lightweight batch processing engine developed by University of Notre Dame, which ALICE uses to orchestrate release validation. Finally, we will give an outlook on how to use Mesos as resource manager for DDS, a software deployment system developed by GSI which will be the foundation of the system deployment for ALICE next generation Online-Offline (O2).

Epistemic Stance in Spoken L2 English: The Effect of Task and Speaker Style

ERIC Educational Resources Information Center

Gablasova, Dana; Brezina, Vaclav; Mcenery, Tony; Boyd, Elaine

2017-01-01

The article discusses epistemic stance in spoken L2 production. Using a subset of the Trinity Lancaster Corpus of spoken L2 production, we analysed the speech of 132 advanced L2 speakers from different L1 and cultural backgrounds taking part in four speaking tasks: one largely monologic presentation task and three interactive tasks. The study…

Negotiation of Meaning and Modified Output Elicitation across Two Tasks

ERIC Educational Resources Information Center

Rahimian, Mehdi

2013-01-01

Analysing the effects of second language (L2) production on L2 learners' interlanguage (IL) modifications is the main scope of this paper. For this purpose, English L2 learners' output production and IL modifications in performing two different task types, one-way and two-way tasks, are compared. The one-way task used in this study was a story…

Cognitive timing: neuropsychology and anatomic basis.

PubMed

Coslett, H Branch; Shenton, Jeff; Dyer, Tamarah; Wiener, Martin

2009-02-13

We report data from 31 subjects with focal hemisphere lesions (15 left hemisphere) as well as 16 normal controls on a battery of tasks assessing the estimation, production and reproduction of time intervals ranging from 2-12 s. Both visual and auditory stimuli were employed for the estimation and production tasks. First, ANOVAs were performed to assess the effect of stimulus modality on estimation and production tasks; a significant effect of stimulus modality was observed for the production but not the estimation task. Second, accuracy was significantly different for the 2 s interval as compared to longer intervals. Subsequent analyses of the data from 4-12 s stimuli demonstrated that patients with brain lesions were more variable than controls on the estimation and reproduction tasks. Additionally, patients with brain lesions but not controls exhibited significant differences in performance on the different tasks; patients with brain lesions under-produced but over-estimated time intervals of 4-12 s but performed relatively well on the reproduction task, a pattern of performance consistent with a "fast clock". There was a significant correlation between impaired performance and lesions of the parietal lobe but there was no effect of laterality of lesion or correlation between lateral frontal lobe lesions and impairment on any task.

Power system restoration - A task force report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adibi, M.; Clelland, P.; Fink, L.

1986-01-01

The IEEE PES System Operation Subcommittee has established the Power System Restoration Task Force to: review operating practices, conduct a literature search, prepare relevant glossaries and bibliographies, and promote information exchange through technical papers. This is the first report of the Task Force. The problem of bulk power system restoration following a complete or partial collapse is practically as old as the electric utility industry itself. Many electric utilities have developed over the years system restoration schemes that meet the needs of their particular systems. These plans provide a great deal of insight into how the restorative process is viewedmore » by operating and planning personnel and what concerns and constraints any plan must operate under. The body of the report consists of notes prepared by members of the Task Force. It should not be interred that a complete reporting on Power System Restoration is undertaken here. The intent is to report upon work of the Task Force to date. The report also reviews several different restoration plans and shows their common concerns and constraints.« less

Increasing Independence in Self-Care Tasks for Children with Autism Using Self-Operated Auditory Prompts

ERIC Educational Resources Information Center

Mays, Nicole McGaha; Heflin, L. Juane

2011-01-01

This study was conducted to determine the effects of self-operated auditory prompting systems (SOAPs) on independent self-care task completion of elementary-school-aged children with autism and intellectual disabilities. Prerecorded verbal prompts on a student-operated tape recorder were employed to facilitate independence in washing hands and…

Ornamental Horticulture Production Occupations. Curriculum Guide.

ERIC Educational Resources Information Center

Reneau, Fred; And Others

This curriculum guide contains guidesheets for the ornamental horticulture production occupations. Each guidesheet provides a job-relevant task; performance objective, with task, performance standard, source of standard, and conditions for performance of task; enabling objectives; a list of resources; teaching activities; a criterion-referenced…

CMS tier structure and operation of the experiment-specific tasks in Germany

NASA Astrophysics Data System (ADS)

Nowack, A.

2008-07-01

In Germany, several university institutes and research centres take part in the CMS experiment. Concerning the data analysis, a couple of computing centres at different Tier levels, ranging from Tier 1 to Tier 3, exists at these places. The German Tier 1 centre GridKa at the research centre at Karlsruhe serves all four LHC experiments as well as four non-LHC experiments. With respect to the CMS experiment, GridKa is mainly involved in central tasks. The Tier 2 centre in Germany consists of two sites, one at the research centre DESY at Hamburg and one at RWTH Aachen University, forming a federated Tier 2 centre. Both parts cover different aspects of a Tier 2 centre. The German Tier 3 centres are located at the research centre DESY at Hamburg, at RWTH Aachen University, and at the University of Karlsruhe. Furthermore the building of a German user analysis facility is planned. Since the CMS community in German is rather small, a good cooperation between the different sites is essential. This cooperation includes physical topics as well as technical and operational issues. All available communication channels such as email, phone, monthly video conferences, and regular personal meetings are used. For example, the distribution of data sets is coordinated globally within Germany. Also the CMS-specific services such as the data transfer tool PhEDEx or the Monte Carlo production are operated by people from different sites in order to spread the knowledge widely and increase the redundancy in terms of operators.

Power system restoration - A task force report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adibi, M.; Clelland, P.; Link, L.

1987-05-01

The IEEE PES System Operation Subcommittee has established the Power System Restoration Task Force to: review operating practices, conduct a literature search, prepare relevant glossaries and bibliographies, and promote information exchange through technical papers. This is the first report of the Task Force. The problem of bulk power system restoration following a complete or partial collapse is practically as old as the electric utility industry itself. Many electric utilities have developed over the years system restoration schemes that meet the needs of their particular systems. These plans provide a great deal of insight into how the restorative process is viewedmore » by operating and planning personnel and what concerns and constraints any plan must operate under.« less

The effects of syntactic complexity on the human-computer interaction

NASA Technical Reports Server (NTRS)

Chechile, R. A.; Fleischman, R. N.; Sadoski, D. M.

1986-01-01

Three divided-attention experiments were performed to evaluate the effectiveness of a syntactic analysis of the primary task of editing flight route-way-point information. For all editing conditions, a formal syntactic expression was developed for the operator's interaction with the computer. In terms of the syntactic expression, four measures of syntactic were examined. Increased syntactic complexity did increase the time to train operators, but once the operators were trained, syntactic complexity did not influence the divided-attention performance. However, the number of memory retrievals required of the operator significantly accounted for the variation in the accuracy, workload, and task completion time found on the different editing tasks under attention-sharing conditions.

Who multi-tasks and why? Multi-tasking ability, perceived multi-tasking ability, impulsivity, and sensation seeking.

PubMed

Sanbonmatsu, David M; Strayer, David L; Medeiros-Ward, Nathan; Watson, Jason M

2013-01-01

The present study examined the relationship between personality and individual differences in multi-tasking ability. Participants enrolled at the University of Utah completed measures of multi-tasking activity, perceived multi-tasking ability, impulsivity, and sensation seeking. In addition, they performed the Operation Span in order to assess their executive control and actual multi-tasking ability. The findings indicate that the persons who are most capable of multi-tasking effectively are not the persons who are most likely to engage in multiple tasks simultaneously. To the contrary, multi-tasking activity as measured by the Media Multitasking Inventory and self-reported cell phone usage while driving were negatively correlated with actual multi-tasking ability. Multi-tasking was positively correlated with participants' perceived ability to multi-task ability which was found to be significantly inflated. Participants with a strong approach orientation and a weak avoidance orientation--high levels of impulsivity and sensation seeking--reported greater multi-tasking behavior. Finally, the findings suggest that people often engage in multi-tasking because they are less able to block out distractions and focus on a singular task. Participants with less executive control--low scorers on the Operation Span task and persons high in impulsivity--tended to report higher levels of multi-tasking activity.

Spectral fitting, shock layer modeling, and production of nitrogen oxides and excited nitrogen

NASA Technical Reports Server (NTRS)

Blackwell, H. E.

1991-01-01

An analysis was made of N2 emission from 8.72 MJ/kg shock layer at 2.54, 1.91, and 1.27 cm positions and vibrational state distributions, temperatures, and relative electronic state populations was obtained from data sets. Other recorded arc jet N2 and air spectral data were reviewed and NO emission characteristics were studied. A review of operational procedures of the DSMC code was made. Information on other appropriate codes and modifications, including ionization, were made as well as a determination of the applicability of codes reviewed to task requirement. A review was also made of computational procedures used in CFD codes of Li and other codes on JSC computers. An analysis was made of problems associated with integration of specific chemical kinetics applicable to task into CFD codes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, Gregory S.; Nickless, William K.; Thiede, David R.

Enterprise level cyber security requires the deployment, operation, and monitoring of many sensors across geographically dispersed sites. Communicating with the sensors to gather data and control behavior is a challenging task when the number of sensors is rapidly growing. This paper describes the system requirements, design, and implementation of T3, the third generation of our transport software that performs this task. T3 relies on open source software and open Internet standards. Data is encoded in MIME format messages and transported via NNTP, which provides scalability. OpenSSL and public key cryptography are used to secure the data. Robustness and ease ofmore » development are increased by defining an internal cryptographic API, implemented by modules in C, Perl, and Python. We are currently using T3 in a production environment. It is freely available to download and use for other projects.« less

Surface operations usability study utilizing Capstone phase I avionics : quick look report

DOT National Transportation Integrated Search

2000-10-07

Evaluate usability, suitability and acceptability of of the surface moving map implemented within Capstone Phase 1 Avionics for surface operations : Task 1: Airport Surface Situational Awareness (ASSA) : Task 2: Surface-Final Approach Runway Occupanc...

An application of multiattribute decision analysis to the Space Station Freedom program. Case study: Automation and robotics technology evaluation

NASA Technical Reports Server (NTRS)

Smith, Jeffrey H.; Levin, Richard R.; Carpenter, Elisabeth J.

1990-01-01

The results are described of an application of multiattribute analysis to the evaluation of high leverage prototyping technologies in the automation and robotics (A and R) areas that might contribute to the Space Station (SS) Freedom baseline design. An implication is that high leverage prototyping is beneficial to the SS Freedom Program as a means for transferring technology from the advanced development program to the baseline program. The process also highlights the tradeoffs to be made between subsidizing high value, low risk technology development versus high value, high risk technology developments. Twenty one A and R Technology tasks spanning a diverse array of technical concepts were evaluated using multiattribute decision analysis. Because of large uncertainties associated with characterizing the technologies, the methodology was modified to incorporate uncertainty. Eight attributes affected the rankings: initial cost, operation cost, crew productivity, safety, resource requirements, growth potential, and spinoff potential. The four attributes of initial cost, operations cost, crew productivity, and safety affected the rankings the most.

Technical support for Life Sciences communities on a production grid infrastructure.

PubMed

Michel, Franck; Montagnat, Johan; Glatard, Tristan

2012-01-01

Production operation of large distributed computing infrastructures (DCI) still requires a lot of human intervention to reach acceptable quality of service. This may be achievable for scientific communities with solid IT support, but it remains a show-stopper for others. Some application execution environments are used to hide runtime technical issues from end users. But they mostly aim at fault-tolerance rather than incident resolution, and their operation still requires substantial manpower. A longer-term support activity is thus needed to ensure sustained quality of service for Virtual Organisations (VO). This paper describes how the biomed VO has addressed this challenge by setting up a technical support team. Its organisation, tooling, daily tasks, and procedures are described. Results are shown in terms of resource usage by end users, amount of reported incidents, and developed software tools. Based on our experience, we suggest ways to measure the impact of the technical support, perspectives to decrease its human cost and make it more community-specific.

The advanced software development workstation project

NASA Technical Reports Server (NTRS)

Fridge, Ernest M., III; Pitman, Charles L.

1991-01-01

The Advanced Software Development Workstation (ASDW) task is researching and developing the technologies required to support Computer Aided Software Engineering (CASE) with the emphasis on those advanced methods, tools, and processes that will be of benefit to support all NASA programs. Immediate goals are to provide research and prototype tools that will increase productivity, in the near term, in projects such as the Software Support Environment (SSE), the Space Station Control Center (SSCC), and the Flight Analysis and Design System (FADS) which will be used to support the Space Shuttle and Space Station Freedom. Goals also include providing technology for development, evolution, maintenance, and operations. The technologies under research and development in the ASDW project are targeted to provide productivity enhancements during the software life cycle phase of enterprise and information system modeling, requirements generation and analysis, system design and coding, and system use and maintenance. On-line user's guides will assist users in operating the developed information system with knowledge base expert assistance.

Can spectro-temporal complexity explain the autistic pattern of performance on auditory tasks?

PubMed

Samson, Fabienne; Mottron, Laurent; Jemel, Boutheina; Belin, Pascal; Ciocca, Valter

2006-01-01

To test the hypothesis that level of neural complexity explain the relative level of performance and brain activity in autistic individuals, available behavioural, ERP and imaging findings related to the perception of increasingly complex auditory material under various processing tasks in autism were reviewed. Tasks involving simple material (pure tones) and/or low-level operations (detection, labelling, chord disembedding, detection of pitch changes) show a superior level of performance and shorter ERP latencies. In contrast, tasks involving spectrally- and temporally-dynamic material and/or complex operations (evaluation, attention) are poorly performed by autistics, or generate inferior ERP activity or brain activation. Neural complexity required to perform auditory tasks may therefore explain pattern of performance and activation of autistic individuals during auditory tasks.

Dual-task interference with equal task emphasis: graded capacity sharing or central postponement?

NASA Technical Reports Server (NTRS)

Ruthruff, Eric; Pashler, Harold E.; Hazeltine, Eliot

2003-01-01

Most studies using the psychological refractory period (PRP) design suggest that dual-task performance is limited by a central bottleneck. Because subjects are usually told to emphasize Task 1, however, the bottleneck might reflect a strategic choice rather than a structural limitation. To evaluate the possibility that central operations can proceed in parallel, albeit with capacity limitations, we conducted two dual-task experiments with equal task emphasis. In both experiments, subjects tended to either group responses together or respond to one task well before the other. In addition, stimulus-response compatibility effects were roughly constant across stimulus onset asynchronies (SOAs). At the short SOA, compatibility effects also carried over onto response times for the other task. This pattern of results is difficult to reconcile with the possibility that subjects share capacity roughly equally between simultaneous central operations. However, this pattern is consistent with the existence of a structural central bottleneck.

The effects of level of knowledge upon human problem solving in a process control task

NASA Technical Reports Server (NTRS)

Morris, N. M.; Rouse, W. B.

1983-01-01

The effect of knowledge of a system on the performance of the operator has been investigated using PLANT, a generic simulation of a process. Four sets of written instructions representing the what, how, and why of system control were utilized by groups of subjects who controlled PLANT in a variety of familiar and unfamiliar situations. Written test results at the end of the experiments showed that the instructions had no effect on the primary goal of production, but those groups receiving guidelines for operation (the how) controlled the system in a more stable manner. Principles (the why) had no apparent effect on the subjects' performance. There was no difference between groups in diagnosing unfamiliar events.

Investigation of cloud/water vapor motion winds from geostationary satellite

NASA Technical Reports Server (NTRS)

1993-01-01

This report summarizes the research work accomplished on the NASA grant contract NAG8-892 during 1992. Research goals of this contract are the following: to complete upgrades to the Cooperative Institute for Meteorological Satellite Studies (CIMSS) wind system procedures for assigning heights and incorporating first guess information; to evaluate these modifications using simulated tracer fields; to add an automated quality control system to minimize the need for manual editing, while maintaining product quality; and to benchmark the upgraded algorithm in tests with NMC and/or MSFC. Work progressed on all these tasks and is detailed. This work was done in collaboration with CIMSS NOAA/NESDIS scientists working on the operational winds software, so that NASA funded research can benefit NESDIS operational algorithms.

NMESys: An expert system for network fault detection

NASA Technical Reports Server (NTRS)

Nelson, Peter C.; Warpinski, Janet

1991-01-01

The problem of network management is becoming an increasingly difficult and challenging task. It is very common today to find heterogeneous networks consisting of many different types of computers, operating systems, and protocols. The complexity of implementing a network with this many components is difficult enough, while the maintenance of such a network is an even larger problem. A prototype network management expert system, NMESys, implemented in the C Language Integrated Production System (CLIPS). NMESys concentrates on solving some of the critical problems encountered in managing a large network. The major goal of NMESys is to provide a network operator with an expert system tool to quickly and accurately detect hard failures, potential failures, and to minimize or eliminate user down time in a large network.

Behavioral technology and its application to fire toxicology research

NASA Technical Reports Server (NTRS)

Russo, D. M.

1978-01-01

The application of behavioral technology to the toxicity testing of pyrolysis/combustion (P/C) products is discussed and two categories of behavioral tests commonly employed in fire toxicology programs are reviewed. Data are presented from a comparison of carbon monoxide (CO) induced incapacitation in rats performing in a rotating wheel or under a Sidmon free-operant schedule of shock avoidance. Rats performing in the rotating wheel were behaviorally incapacitated at CO concentrations and carboxyhemoglobin levels significantly lower than those which incapacitated operant avoidance animals. It is concluded that different measures of behavioral incapacitation may vary since incapacitation is a function of the particular toxic mechanism at work and the behavioral requirements of the specific task employed in the test procedure.

Carolina Offshore Wind Integration Case Study: Phases I and II Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fallon, Christopher; Piper, Orvane; Hazelip, William

2015-04-30

Duke Energy performed a phase 1 study to assess the impact of offshore wind development in the waters off the coasts of North Carolina and South Carolina. The study analyzed the impacts to the Duke Energy Carolinas electric power system of multiple wind deployment scenarios. Focusing on an integrated utility system in the Carolinas provided a unique opportunity to assess the impacts of offshore wind development in a region that has received less attention regarding renewables than others in the US. North Carolina is the only state in the Southeastern United States that currently has a renewable portfolio standard (RPS)more » which requires that 12.5% of the state’s total energy requirements be met with renewable resources by 2021. 12.5% of the state’s total energy requirements in 2021 equates to approximately 17,000 GWH of energy needed from renewable resources. Wind resources represent one of the ways to potentially meet this requirement. The study builds upon and augments ongoing work, including a study by UNC to identify potential wind development sites and the analysis of impacts to the regional transmission system performed by the NCTPC, an Order 890 planning entity of which DEC is a member. Furthermore, because the region does not have an independent system operator (ISO) or regional transmission organization (RTO), the study will provide additional information unique to non-RTO/ISO systems. The Phase 2 study builds on the results of Phase 1 and investigates the dynamic stability of the electrical network in Task 4, the operating characteristics of the wind turbines as they impact operating reserve requirements of the DEC utility in Task 5, and the production cost of integrating the offshore wind resources into the DEC generation fleet making comparisons to future planned operation without the addition of the wind resources in Task 6.« less

Re-engineering the mission life cycle with ABC and IDEF

NASA Technical Reports Server (NTRS)

Mandl, Daniel; Rackley, Michael; Karlin, Jay

1994-01-01

The theory behind re-engineering a business process is to remove the non-value added activities thereby lowering the process cost. In order to achieve this, one must be able to identify where the non-value added elements are located which is not a trivial task. This is because the non-value added elements are often hidden in the form of overhead and/or pooled resources. In order to be able to isolate these non-value added processes from among the other processes, one must first decompose the overall top level process into lower layers of sub-processes. In addition, costing data must be assigned to each sub-process along with the value the sub-process adds towards the final product. IDEF0 is a Federal Information Processing Standard (FIPS) process-modeling tool that allows for this functional decomposition through structured analysis. In addition, it illustrates the relationship of the process and the value added to the product or service. The value added portion is further defined in IDEF1X which is an entity relationship diagramming tool. The entity relationship model is the blueprint of the product as it moves along the 'assembly line' and therefore relates all of the parts to each other and the final product. It also relates the parts to the tools that produce the product and all of the paper work that is used in their acquisition. The use of IDEF therefore facilitates the use of Activity Based Costing (ABC). ABC is an essential method in a high variety, product-customizing environment, to facilitate rapid response to externally caused change. This paper describes the work being done in the Mission Operations Division to re-engineer the development and operation life cycle of Mission Operations Centers using these tools.

Contributions of Hippocampus and Striatum to Memory-Guided Behavior Depend on Past Experience

PubMed Central

2016-01-01

The hippocampal and striatal memory systems are thought to operate independently and in parallel in supporting cognitive memory and habits, respectively. Much of the evidence for this principle comes from double dissociation data, in which damage to brain structure A causes deficits in Task 1 but not Task 2, whereas damage to structure B produces the reverse pattern of effects. Typically, animals are explicitly trained in one task. Here, we investigated whether this principle continues to hold when animals concurrently learn two types of tasks. Rats were trained on a plus maze in either a spatial navigation or a cue–response task (sequential training), whereas a third set of rats acquired both (concurrent training). Subsequently, the rats underwent either sham surgery or neurotoxic lesions of the hippocampus (HPC), medial dorsal striatum (DSM), or lateral dorsal striatum (DSL), followed by retention testing. Finally, rats in the sequential training condition also acquired the novel “other” task. When rats learned one task, HPC and DSL selectively supported spatial navigation and cue response, respectively. However, when rats learned both tasks, HPC and DSL additionally supported the behavior incongruent with the processing style of the corresponding memory system. Thus, in certain conditions, the hippocampal and striatal memory systems can operate cooperatively and in synergism. DSM significantly contributed to performance regardless of task or training procedure. Experience with the cue–response task facilitated subsequent spatial learning, whereas experience with spatial navigation delayed both concurrent and subsequent response learning. These findings suggest that there are multiple operational principles that govern memory networks. SIGNIFICANCE STATEMENT Currently, we distinguish among several types of memories, each supported by a distinct neural circuit. The memory systems are thought to operate independently and in parallel. Here, we demonstrate that the hippocampus and the dorsal striatum memory systems operate independently and in parallel when rats learn one type of task at a time, but interact cooperatively and in synergism when rats concurrently learn two types of tasks. Furthermore, new learning is modulated by past experiences. These results can be explained by a model in which independent and parallel information processing that occurs in the separate memory-related neural circuits is supplemented by information transfer between the memory systems at the level of the cortex. PMID:27307234

Contributions of Hippocampus and Striatum to Memory-Guided Behavior Depend on Past Experience.

PubMed

Ferbinteanu, Janina

2016-06-15

The hippocampal and striatal memory systems are thought to operate independently and in parallel in supporting cognitive memory and habits, respectively. Much of the evidence for this principle comes from double dissociation data, in which damage to brain structure A causes deficits in Task 1 but not Task 2, whereas damage to structure B produces the reverse pattern of effects. Typically, animals are explicitly trained in one task. Here, we investigated whether this principle continues to hold when animals concurrently learn two types of tasks. Rats were trained on a plus maze in either a spatial navigation or a cue-response task (sequential training), whereas a third set of rats acquired both (concurrent training). Subsequently, the rats underwent either sham surgery or neurotoxic lesions of the hippocampus (HPC), medial dorsal striatum (DSM), or lateral dorsal striatum (DSL), followed by retention testing. Finally, rats in the sequential training condition also acquired the novel "other" task. When rats learned one task, HPC and DSL selectively supported spatial navigation and cue response, respectively. However, when rats learned both tasks, HPC and DSL additionally supported the behavior incongruent with the processing style of the corresponding memory system. Thus, in certain conditions, the hippocampal and striatal memory systems can operate cooperatively and in synergism. DSM significantly contributed to performance regardless of task or training procedure. Experience with the cue-response task facilitated subsequent spatial learning, whereas experience with spatial navigation delayed both concurrent and subsequent response learning. These findings suggest that there are multiple operational principles that govern memory networks. Currently, we distinguish among several types of memories, each supported by a distinct neural circuit. The memory systems are thought to operate independently and in parallel. Here, we demonstrate that the hippocampus and the dorsal striatum memory systems operate independently and in parallel when rats learn one type of task at a time, but interact cooperatively and in synergism when rats concurrently learn two types of tasks. Furthermore, new learning is modulated by past experiences. These results can be explained by a model in which independent and parallel information processing that occurs in the separate memory-related neural circuits is supplemented by information transfer between the memory systems at the level of the cortex. Copyright © 2016 the authors 0270-6474/16/366459-12$15.00/0.

Report of the Task Force on SSC Magnet System Test Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1984-10-01

The Task Force on SSC Magnet Systems test Site was appointed by Maury Tigner, Director of the SSC, Phase 1 in August 1984. In brief, the charge asked the Task Force to make a critical evaluation of potential test sites for a major SSC magnet System Test Facility (STF) with regard to: (1) availability of the needed space, utilities, staff and other requirements on the desired time scale; and (2) the cost of preparing the sites for the tests and for operating the facilities during the test period. The charge further suggests that, by virtue of existing facilities and availabilitymore » of experienced staff, BNL and FNAL are the two best candidate sites and that is therefore appears appropriate to restrict the considerations of the Task Force to these sites. During the subsequent deliberations of the Task Force, no new facts were revealed that altered the assumptions of the charge in this regard. The charge does not ask for a specific site recommendation for the STF. Indeed, an agreement on such a recommendation would be difficult to achieve considering the composition of the Task Force, wherein a large fraction of the membership is drawn from the two contending laboratories. Instead, we have attempted to describe the purpose of the facility, outline a productive test program, list the major facilities required, carefully review the laboratories` responses to the facility requirements, and make objective comparisons of the specific features and capabilities offered.« less

Flight and Operational Medicine Clinic (FOMC) Task Process Mapping

DTIC Science & Technology

2014-03-01

technicians, nurses, and physician assistants to accomplish the majority of the tasks; physician level tasks are few and primarily involve application of...condition 31, 37, 81? Complete evaluation Present 469 within 5 days of positive pregnancy test Is condition duty/fitness? NO End Process YES Send to ...info to Health IT Ancillary exam module provides requirements/ sends info to Health IT (Audiology, Optometry, Dental , Mental Health) Operational

A 1-night operant learning task without food-restriction differentiates among mouse strains in an automated home-cage environment.

PubMed

Remmelink, Esther; Loos, Maarten; Koopmans, Bastijn; Aarts, Emmeke; van der Sluis, Sophie; Smit, August B; Verhage, Matthijs

2015-04-15

Individuals are able to change their behavior based on its consequences, a process involving instrumental learning. Studying instrumental learning in mice can provide new insights in this elementary aspect of cognition. Conventional appetitive operant learning tasks that facilitate the study of this form of learning in mice, as well as more complex operant paradigms, require labor-intensive handling and food deprivation to motivate the animals. Here, we describe a 1-night operant learning protocol that exploits the advantages of automated home-cage testing and circumvents the interfering effects of food restriction. The task builds on behavior that is part of the spontaneous exploratory repertoire during the days before the task. We compared the behavior of C57BL/6J, BALB/cJ and DBA/2J mice and found various differences in behavior during this task, but no differences in learning curves. BALB/cJ mice showed the largest instrumental learning response, providing a superior dynamic range and statistical power to study instrumental learning by using this protocol. Insights gained with this home-cage-based learning protocol without food restriction will be valuable for the development of other, more complex, cognitive tasks in automated home-cages. Copyright © 2015 Elsevier B.V. All rights reserved.

The Effects of Pre-Task Planning and On-line Planning on Fluency, Complexity, and Accuracy in L2 Monologic Oral Production.

ERIC Educational Resources Information Center

Yuan, Fangyuan; Ellis, Rod

2003-01-01

Investigated the effects of both pre-task and on-line planning on second language (L2) oral production. Results show that pre-task planning enhances grammatical complexity while on-line planning positively influences accuracy and grammatical complexity. Pre-task planners also produced more fluent and lexically varied language than the on-line…

Safety and Mission Assurance (SMA) Automated Task Order Management System (ATOMS) Operation Manual

NASA Technical Reports Server (NTRS)

Wallace, Shawn; Fikes, Lou A.

2016-01-01

This document describes operational aspects of the ATOMS system. The information provided is limited to the functionality provided by ATOMS and does not include information provided in the contractor's proprietary financial and task management system.

Emergency response nurse scheduling with medical support robot by multi-agent and fuzzy technique.

PubMed

Kono, Shinya; Kitamura, Akira

2015-08-01

In this paper, a new co-operative re-scheduling method corresponding the medical support tasks that the time of occurrence can not be predicted is described, assuming robot can co-operate medical activities with the nurse. Here, Multi-Agent-System (MAS) is used for the co-operative re-scheduling, in which Fuzzy-Contract-Net (FCN) is applied to the robots task assignment for the emergency tasks. As the simulation results, it is confirmed that the re-scheduling results by the proposed method can keep the patients satisfaction and decrease the work load of the nurse.

Enhanced control and sensing for the REMOTEC ANDROS Mk VI robot. CRADA final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spelt, P.F.; Harvey, H.W.

1998-08-01

This Cooperative Research and Development Agreement (CRADA) between Lockheed Martin Energy Systems, Inc., and REMOTEC, Inc., explored methods of providing operator feedback for various work actions of the ANDROS Mk VI teleoperated robot. In a hazardous environment, an extremely heavy workload seriously degrades the productivity of teleoperated robot operators. This CRADA involved the addition of computer power to the robot along with a variety of sensors and encoders to provide information about the robot`s performance in and relationship to its environment. Software was developed to integrate the sensor and encoder information and provide control input to the robot. ANDROS Mkmore » VI robots are presently used by numerous electric utilities to perform tasks in reactors where substantial exposure to radiation exists, as well as in a variety of other hazardous environments. Further, this platform has potential for use in a number of environmental restoration tasks, such as site survey and detection of hazardous waste materials. The addition of sensors and encoders serves to make the robot easier to manage and permits tasks to be done more safely and inexpensively (due to time saved in the completion of complex remote tasks). Prior research on the automation of mobile platforms with manipulators at Oak Ridge National Laboratory`s Center for Engineering Systems Advanced Research (CESAR, B&R code KC0401030) Laboratory, a BES-supported facility, indicated that this type of enhancement is effective. This CRADA provided such enhancements to a successful working teleoperated robot for the first time. Performance of this CRADA used the CESAR laboratory facilities and expertise developed under BES funding.« less

Effects of automation and task load on task switching during human supervision of multiple semi-autonomous robots in a dynamic environment.

PubMed

Squire, P N; Parasuraman, R

2010-08-01

The present study assessed the impact of task load and level of automation (LOA) on task switching in participants supervising a team of four or eight semi-autonomous robots in a simulated 'capture the flag' game. Participants were faster to perform the same task than when they chose to switch between different task actions. They also took longer to switch between different tasks when supervising the robots at a high compared to a low LOA. Task load, as manipulated by the number of robots to be supervised, did not influence switch costs. The results suggest that the design of future unmanned vehicle (UV) systems should take into account not simply how many UVs an operator can supervise, but also the impact of LOA and task operations on task switching during supervision of multiple UVs. The findings of this study are relevant for the ergonomics practice of UV systems. This research extends the cognitive theory of task switching to inform the design of UV systems and results show that switching between UVs is an important factor to consider.

Operation Compatibility: A Neglected Contribution to Dual-Task Costs

ERIC Educational Resources Information Center

Pannebakker, Merel M.; Band, Guido P. H.; Ridderinkhof, K. Richard

2009-01-01

Traditionally, dual-task interference has been attributed to the consequences of task load exceeding capacity limitations. However, the current study demonstrates that in addition to task load, the mutual compatibility of the concurrent processes modulates whether 2 tasks can be performed in parallel. In 2 psychological refractory period…

Using near infrared spectroscopy and heart rate variability to detect mental overload.

PubMed

Durantin, G; Gagnon, J-F; Tremblay, S; Dehais, F

2014-02-01

Mental workload is a key factor influencing the occurrence of human error, especially during piloting and remotely operated vehicle (ROV) operations, where safety depends on the ability of pilots to act appropriately. In particular, excessively high or low mental workload can lead operators to neglect critical information. The objective of the present study is to investigate the potential of functional near infrared spectroscopy (fNIRS) - a non-invasive method of measuring prefrontal cortex activity - in combination with measurements of heart rate variability (HRV), to predict mental workload during a simulated piloting task, with particular regard to task engagement and disengagement. Twelve volunteers performed a computer-based piloting task in which they were asked to follow a dynamic target with their aircraft, a task designed to replicate key cognitive demands associated with real life ROV operating tasks. In order to cover a wide range of mental workload levels, task difficulty was manipulated in terms of processing load and difficulty of control - two critical sources of workload associated with piloting and remotely operating a vehicle. Results show that both fNIRS and HRV are sensitive to different levels of mental workload; notably, lower prefrontal activation as well as a lower LF/HF ratio at the highest level of difficulty, suggest that these measures are suitable for mental overload detection. Moreover, these latter measurements point toward the existence of a quadratic model of mental workload. Copyright © 2013 Elsevier B.V. All rights reserved.

The Line Operations Safety Audit Program: Transitioning From Flight Operations to Maintenance and Ramp Operations

DTIC Science & Technology

2011-09-01

Transport Association ( ATA ) Maintenance & Ramp Human Factors Task Force committee members—we are deeply grateful for their contributions in the...6 Air Transport Association ( ATA ) Human Factors Task Force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Form Development...garnered many valuable les- sons, safety improvements, and significant returns on their investment. 1The FAA ATA Human Factors Taskforce has

Graphics simulation and training aids for advanced teleoperation

NASA Technical Reports Server (NTRS)

Kim, Won S.; Schenker, Paul S.; Bejczy, Antal K.

1993-01-01

Graphics displays can be of significant aid in accomplishing a teleoperation task throughout all three phases of off-line task analysis and planning, operator training, and online operation. In the first phase, graphics displays provide substantial aid to investigate work cell layout, motion planning with collision detection and with possible redundancy resolution, and planning for camera views. In the second phase, graphics displays can serve as very useful tools for introductory training of operators before training them on actual hardware. In the third phase, graphics displays can be used for previewing planned motions and monitoring actual motions in any desired viewing angle, or, when communication time delay prevails, for providing predictive graphics overlay on the actual camera view of the remote site to show the non-time-delayed consequences of commanded motions in real time. This paper addresses potential space applications of graphics displays in all three operational phases of advanced teleoperation. Possible applications are illustrated with techniques developed and demonstrated in the Advanced Teleoperation Laboratory at JPL. The examples described include task analysis and planning of a simulated Solar Maximum Satellite Repair task, a novel force-reflecting teleoperation simulator for operator training, and preview and predictive displays for on-line operations.

Evaluation of 2 cognitive abilities tests in a dual-task environment

NASA Technical Reports Server (NTRS)

Vidulich, M. A.; Tsang, P. S.

1986-01-01

Most real world operators are required to perform multiple tasks simultaneously. In some cases, such as flying a high performance aircraft or trouble shooting a failing nuclear power plant, the operator's ability to time share or process in parallel" can be driven to extremes. This has created interest in selection tests of cognitive abilities. Two tests that have been suggested are the Dichotic Listening Task and the Cognitive Failures Questionnaire. Correlations between these test results and time sharing performance were obtained and the validity of these tests were examined. The primary task was a tracking task with dynamically varying bandwidth. This was performed either alone or concurrently with either another tracking task or a spatial transformation task. The results were: (1) An unexpected negative correlation was detected between the two tests; (2) The lack of correlation between either test and task performance made the predictive utility of the tests scores appear questionable; (3) Pilots made more errors on the Dichotic Listening Task than college students.

Comparative analysis of operational forecasts versus actual weather conditions in airline flight planning: Summary report

NASA Technical Reports Server (NTRS)

Keitz, J. F.

1982-01-01

The impact of more timely and accurate weather data on airline flight planning with the emphasis on fuel savings is studied. This summary report discusses the results of each of the four major tasks of the study. Task 1 compared airline flight plans based on operational forecasts to plans based on the verifying analyses and found that average fuel savings of 1.2 to 2.5 percent are possible with improved forecasts. Task 2 consisted of similar comparisons but used a model developed for the FAA by SRI International that simulated the impact of ATc diversions on the flight plans. While parts of Task 2 confirm the Task I findings, inconsistency with other data and the known impact of ATC suggests that other Task 2 findings are the result of errors in the model. Task 3 compares segment weather data from operational flight plans with the weather actually observed by the aircraft and finds the average error could result in fuel burn penalties (or savings) of up to 3.6 percent for the average 8747 flight. In Task 4 an in-depth analysis of the weather forecast for the 33 days included in the study finds that significant errors exist on 15 days. Wind speeds in the area of maximum winds are underestimated by 20 to 50 kts., a finding confirmed in the other three tasks.

The Projects for Onboard Autonomy (PROBA2) Science Centre: Sun Watcher Using APS Detectors and Image Processing (SWAP) and Large-Yield Radiometer (LYRA) Science Operations and Data Products

NASA Astrophysics Data System (ADS)

Zender, J.; Berghmans, D.; Bloomfield, D. S.; Cabanas Parada, C.; Dammasch, I.; De Groof, A.; D'Huys, E.; Dominique, M.; Gallagher, P.; Giordanengo, B.; Higgins, P. A.; Hochedez, J.-F.; Yalim, M. S.; Nicula, B.; Pylyser, E.; Sanchez-Duarte, L.; Schwehm, G.; Seaton, D. B.; Stanger, A.; Stegen, K.; Willems, S.

2013-08-01

The PROBA2 Science Centre (P2SC) is a small-scale science operations centre supporting the Sun observation instruments onboard PROBA2: the EUV imager Sun Watcher using APS detectors and image Processing (SWAP) and Large-Yield Radiometer (LYRA). PROBA2 is one of ESA's small, low-cost Projects for Onboard Autonomy (PROBA) and part of ESA's In-Orbit Technology Demonstration Programme. The P2SC is hosted at the Royal Observatory of Belgium, co-located with both Principal Investigator teams. The P2SC tasks cover science planning, instrument commanding, instrument monitoring, data processing, support of outreach activities, and distribution of science data products. PROBA missions aim for a high degree of autonomy at mission and system level, including the science operations centre. The autonomy and flexibility of the P2SC is reached by a set of web-based interfaces allowing the operators as well as the instrument teams to monitor quasi-continuously the status of the operations, allowing a quick reaction to solar events. In addition, several new concepts are implemented at instrument, spacecraft, and ground-segment levels allowing a high degree of flexibility in the operations of the instruments. This article explains the key concepts of the P2SC, emphasising the automation and the flexibility achieved in the commanding as well as the data-processing chain.

Job satisfaction or production? How staff and leadership understand operating room efficiency: a qualitative study.

PubMed

Arakelian, E; Gunningberg, L; Larsson, J

2008-11-01

How to increase efficiency in operating departments has been widely studied. However, there is no overall definition of efficiency. Supervisors urging staff to work efficiently may meet strong reactions due to staff believing that demands for efficiency means just stress at work. Differences in how efficiency is understood may constitute an obstacle to supervisors' efforts to promote it. This study aimed to explore how staff and leadership understand operating room efficiency. Twenty-one members of staff and supervisors in an operating department in a Swedish county hospital were interviewed. The analysis was performed with a phenomenographic approach that aims to discover the variations in how a phenomenon is understood by a group of people. Six categories were found in the understanding of operation room efficiency: (A) having the right qualifications; (B) enjoying work; (C) planning and having good control and overview; (D) each professional performing the correct tasks; (E) completing a work assignment; and (F) producing as much as possible per time unit. The most significant finding was that most of the nurses and assistant nurses understood efficiency as individual knowledge and experience emphasizing the importance of the work process, whereas the supervisors and physicians understood efficiency in terms of production per time unit or completing an assignment. The concept 'operating room efficiency' is understood in different ways by leadership and staff members. Supervisors who are aware of this variation will have better prerequisites for defining the concept and for creating a common platform towards becoming efficient.

Force-reflection and shared compliant control in operating telemanipulators with time delay

NASA Technical Reports Server (NTRS)

Kim, Won S.; Hannaford, Blake; Bejczy, Antal K.

1992-01-01

The performance of an advanced telemanipulation system in the presence of a wide range of time delays between a master control station and a slave robot is quantified. The contemplated applications include multiple satellite links to LEO, geosynchronous operation, spacecraft local area networks, and general-purpose computer-based short-distance designs. The results of high-precision peg-in-hole tasks performed by six test operators indicate that task performance decreased linearly with introduced time delays for both kinesthetic force feedback (KFF) and shared compliant control (SCC). The rate of this decrease was substantially improved with SCC compared to KFF. Task performance at delays above 1 s was not possible using KFF. SCC enabled task performance for such delays, which are realistic values for ground-controlled remote manipulation of telerobots in space.

Timeliner: Automating Procedures on the ISS

NASA Technical Reports Server (NTRS)

Brown, Robert; Braunstein, E.; Brunet, Rick; Grace, R.; Vu, T.; Zimpfer, Doug; Dwyer, William K.; Robinson, Emily

2002-01-01

Timeliner has been developed as a tool to automate procedural tasks. These tasks may be sequential tasks that would typically be performed by a human operator, or precisely ordered sequencing tasks that allow autonomous execution of a control process. The Timeliner system includes elements for compiling and executing sequences that are defined in the Timeliner language. The Timeliner language was specifically designed to allow easy definition of scripts that provide sequencing and control of complex systems. The execution environment provides real-time monitoring and control based on the commands and conditions defined in the Timeliner language. The Timeliner sequence control may be preprogrammed, compiled from Timeliner "scripts," or it may consist of real-time, interactive inputs from system operators. In general, the Timeliner system lowers the workload for mission or process control operations. In a mission environment, scripts can be used to automate spacecraft operations including autonomous or interactive vehicle control, performance of preflight and post-flight subsystem checkouts, or handling of failure detection and recovery. Timeliner may also be used for mission payload operations, such as stepping through pre-defined procedures of a scientific experiment.

Development and evaluation of a monitoring-aid system for a nuclear power plant in control room system manipulation.

PubMed

Lin, Jhih-Tsong; Chen, Yan-Cheng; Wu, Shih-Chieh; Hwang, Sheue-Ling

2017-01-01

In an advanced nuclear power plant (NPP), the operators are responsible for monitoring a massive number of alarm parameters. To assist the operators, a monitoring-aid system (MAS), that applies four quality control chart methods, was proposed and evaluated. Two types of MAS, namely, text and graph marks, were proposed and compared with the original display. To validate the proposed MAS, 17 professional engineers and operators were invited to join an experiment. Two different system states, normal and abnormal, were simulated. The operators were asked to manipulate the system, monitor the critical parameters, search for operational procedures, and deal with other secondary tasks. The primary and secondary task performance and heart rate were measured. After each task was conducted, three subjective rating questionnaires, namely, mental workload, situation awareness, and preference ratings, were implemented for the proposed MAS and the original system. With the assistance of the MAS, the alarm detection rate, secondary task performance, and subjective mental workload demonstrate significant improvements. The proposed MAS helps the operators monitor critical parameters. Therefore, the MAS should be considered for implementation with the control panel to increase the safety of NPPs. Furthermore, the MAS could reduce the mental workload might decrease the health hazard of the operators.

The Acquisition, Production and Dissemination of Geospatial Data for Emergency Management and Preservation of Cultural Heritage

NASA Astrophysics Data System (ADS)

Santoro, E.

2017-05-01

The crisis management of a disaster, whether caused naturally or by human action, requires a thorough knowledge of the territory involved, with regard to both its terrain and its developed areas. Therefore, it is essential that the National Mapping and Cadastral Agencies (NMCAs) and all other public and scientific institutions responsible for the production of geospatial information closely co-operate in making their data in that field available. This crucial sharing of geographic information is a top-level priority, not only in a disaster emergency situation, but also for effective urban and environmental planning and Cultural Heritage protection and preservation. Geospatial data-sharing, responding to the needs of all institutions involved in disaster surveying operations, is fundamental, as a priority, to the task of avoiding loss of human lives. However, no less important is the acquisition, dissemination and use of this data, in addition to direct, "in-the-field" operations of specialists in geomatics, in order to preserve the Cultural Heritage located in the crisis area. It is in this context that an NMCA such as the Italian Military Geographic Institute (IGMI) plays a key role.

Relating lab to life: Decrements in attention over time predict math productivity among children with ADHD.

PubMed

Fosco, Whitney D; Hawk, Larry W

2017-02-01

A child's ability to sustain attention over time (AOT) is critical in attention-deficit/hyperactivity disorder (ADHD), yet no prior work has examined the extent to which a child's decrement in AOT on laboratory tasks relates to clinically-relevant behavior. The goal of this study is to provide initial evidence for the criterion validity of laboratory assessments of AOT. A total of 20 children with ADHD (7-12 years of age) who were enrolled in a summer treatment program completed two lab attention tasks (a continuous performance task and a self-paced choice discrimination task) and math seatwork. Analyses focused on relations between attention task parameters and math productivity. Individual differences in overall attention (OA) measures (averaged across time) accounted for 23% of the variance in math productivity, supporting the criterion validity of lab measures of attention. The criterion validity was enhanced by consideration of changes in AOT. Performance on all laboratory attention measures deteriorated as time-on-task increased, and individual differences in the decrement in AOT accounted for 40% of the variance in math productivity. The only variable to uniquely predict math productivity was from the self-paced choice discrimination task. This study suggests that attention tasks in the lab do predict a clinically-relevant target behavior in children with ADHD, supporting their use as a means to study attention processes in a controlled environment. Furthermore, this prediction is improved when attention is examined as a function of time-on-task and when the attentional demands are consistent between lab and life contexts.

Developmental relationships between speech and writing: is verb-phrase anaphora production a special case?

PubMed

Donaldson, Morag L; Cooper, Lynn S M

2013-09-01

Young children's speech is typically more linguistically sophisticated than their writing. However, there are grounds for asking whether production of cohesive devices, such as verb-phrase anaphora (VPA), might represent an exception to this developmental pattern, as cohesive devices are generally more important in writing than in speech and so might be expected to be more frequent in children's writing than in their speech. The study reported herein aims to compare the frequency of children's production of VPA constructions (e.g., Mary is eating an apple and so is John) between a written and a spoken task. Forty-eight children participated from each of two age groups: 7-year-olds and 10-year-olds. All the children received both a spoken and a written sentence completion task designed to elicit production of VPA. Task order was counterbalanced. VPA production was significantly more frequent in speech than in writing and when the spoken task was presented first. Surprisingly, the 7-year-olds produced VPA constructions more frequently than the 10-year-olds. Despite the greater importance of cohesion in writing than in speech, children's production of VPA is similar to their production of most other aspects of language in that more sophisticated constructions are used more frequently in speech than in writing. Children's written production of cohesive devices could probably be enhanced by presenting spoken tasks immediately before written tasks. The lower frequency of VPA production in the older children may reflect syntactic priming effects or a belief that they should produce sentences that are as fully specified as possible. © 2012 The British Psychological Society.

A Novel Technique for Running the NASA Legacy Code LAPIN Synchronously With Simulations Developed Using Simulink

NASA Technical Reports Server (NTRS)

Vrnak, Daniel R.; Stueber, Thomas J.; Le, Dzu K.

2012-01-01

This report presents a method for running a dynamic legacy inlet simulation in concert with another dynamic simulation that uses a graphical interface. The legacy code, NASA's LArge Perturbation INlet (LAPIN) model, was coded using the FORTRAN 77 (The Portland Group, Lake Oswego, OR) programming language to run in a command shell similar to other applications that used the Microsoft Disk Operating System (MS-DOS) (Microsoft Corporation, Redmond, WA). Simulink (MathWorks, Natick, MA) is a dynamic simulation that runs on a modern graphical operating system. The product of this work has both simulations, LAPIN and Simulink, running synchronously on the same computer with periodic data exchanges. Implementing the method described in this paper avoided extensive changes to the legacy code and preserved its basic operating procedure. This paper presents a novel method that promotes inter-task data communication between the synchronously running processes.

Gas engine heat pump cycle analysis. Volume 1: Model description and generic analysis

NASA Astrophysics Data System (ADS)

Fischer, R. D.

1986-10-01

The task has prepared performance and cost information to assist in evaluating the selection of high voltage alternating current components, values for component design variables, and system configurations and operating strategy. A steady-state computer model for performance simulation of engine-driven and electrically driven heat pumps was prepared and effectively used for parametric and seasonal performance analyses. Parametric analysis showed the effect of variables associated with design of recuperators, brine coils, domestic hot water heat exchanger, compressor size, engine efficiency, insulation on exhaust and brine piping. Seasonal performance data were prepared for residential and commercial units in six cities with system configurations closely related to existing or contemplated hardware of the five GRI engine contractors. Similar data were prepared for an advanced variable-speed electric unit for comparison purposes. The effect of domestic hot water production on operating costs was determined. Four fan-operating strategies and two brine loop configurations were explored.

Main principles of developing exploitation models of semiconductor devices

NASA Astrophysics Data System (ADS)

Gradoboev, A. V.; Simonova, A. V.

2018-05-01

The paper represents primary tasks, solutions of which allow to develop the exploitation modes of semiconductor devices taking into account complex and combined influence of ionizing irradiation and operation factors. The structure of the exploitation model of the semiconductor device is presented, which is based on radiation and reliability models. Furthermore, it was shown that the exploitation model should take into account complex and combine influence of various ionizing irradiation types and operation factors. The algorithm of developing the exploitation model of the semiconductor devices is proposed. The possibility of creating the radiation model of Schottky barrier diode, Schottky field-effect transistor and Gunn diode is shown based on the available experimental data. The basic exploitation model of IR-LEDs based upon double AlGaAs heterostructures is represented. The practical application of the exploitation models will allow to output the electronic products with guaranteed operational properties.

Nuclear Engineering Technologists in the Nuclear Power Era

ERIC Educational Resources Information Center

Wang, C. H.; And Others

1974-01-01

Describes manpower needs in nuclear engineering in the areas of research and development, architectural engineering and construction supervision, power reactor operations, and regulatory tasks. Outlines a suitable curriculum to prepare students for the tasks related to construction and operation of power reactors. (GS)

Challenging Tasks Lead to Productive Struggle!

ERIC Educational Resources Information Center

Livy, Sharyn; Muir, Tracey; Sullivan, Peter

2018-01-01

Productive struggle leads to productive classrooms where students work on complex problems, are encouraged to take risks, can struggle and fail yet still feel good about working on hard problems (Boaler, 2016). Teachers can foster a classroom culture that values and promotes productive struggle by providing students with challenging tasks. These…

Assuring reliability program effectiveness.

NASA Technical Reports Server (NTRS)

Ball, L. W.

1973-01-01

An attempt is made to provide simple identification and description of techniques that have proved to be most useful either in developing a new product or in improving reliability of an established product. The first reliability task is obtaining and organizing parts failure rate data. Other tasks are parts screening, tabulation of general failure rates, preventive maintenance, prediction of new product reliability, and statistical demonstration of achieved reliability. Five principal tasks for improving reliability involve the physics of failure research, derating of internal stresses, control of external stresses, functional redundancy, and failure effects control. A final task is the training and motivation of reliability specialist engineers.

Temporal production and visuospatial processing.

PubMed

Benuzzi, Francesca; Basso, Gianpaolo; Nichelli, Paolo

2005-12-01

Current models of prospective timing hypothesize that estimated duration is influenced either by the attentional load or by the short-term memory requirements of a concurrent nontemporal task. In the present study, we addressed this issue with four dual-task experiments. In Exp. 1, the effect of memory load on both reaction time and temporal production was proportional to the number of items of a visuospatial pattern to hold in memory. In Exps. 2, 3, and 4, a temporal production task was combined with two visual search tasks involving either pre-attentive or attentional processing. Visual tasks interfered with temporal production: produced intervals were lengthened proportionally to the display size. In contrast, reaction times increased with display size only when a serial, effortful search was required. It appears that memory and perceptual set size, rather than nonspecific attentional or short-term memory load, can influence prospective timing.

Interactive Scene Analysis Module - A sensor-database fusion system for telerobotic environments

NASA Technical Reports Server (NTRS)

Cooper, Eric G.; Vazquez, Sixto L.; Goode, Plesent W.

1992-01-01

Accomplishing a task with telerobotics typically involves a combination of operator control/supervision and a 'script' of preprogrammed commands. These commands usually assume that the location of various objects in the task space conform to some internal representation (database) of that task space. The ability to quickly and accurately verify the task environment against the internal database would improve the robustness of these preprogrammed commands. In addition, the on-line initialization and maintenance of a task space database is difficult for operators using Cartesian coordinates alone. This paper describes the Interactive Scene' Analysis Module (ISAM) developed to provide taskspace database initialization and verification utilizing 3-D graphic overlay modelling, video imaging, and laser radar based range imaging. Through the fusion of taskspace database information and image sensor data, a verifiable taskspace model is generated providing location and orientation data for objects in a task space. This paper also describes applications of the ISAM in the Intelligent Systems Research Laboratory (ISRL) at NASA Langley Research Center, and discusses its performance relative to representation accuracy and operator interface efficiency.

An Overview of the Applied Meteorology Unit (AMU)

NASA Technical Reports Server (NTRS)

Merceret, Francis; Bauman, William; Lambert, Winifred; Short, David; Barrett, Joe; Watson, Leela

2007-01-01

The Applied Meteorology Unit (AMU) acts as a bridge between research and operations by transitioning technology to improve weather support to the Shuttle and American space program. It is a NASA entity operated under a tri-agency agreement by NASA, the US Air Force, and the National Weather Service (NWS). The AMU contract is managed by NASA, operated by ENSCO, Inc. personnel, and is collocated with Range Weather Operations at Cape Canaveral Air Force Station. The AMU is tasked by its customers in the 45th Weather Squadron, Spaceflight Meteorology Group, and the NWS in Melbourne, FL with projects whose results help improve the weather forecast for launch, landing, and ground operations. This presentation describes the history behind the formation of the AMU, its working relationships and goals, how it is tasked by its customers, and examples of completed tasks.

Solar energy and conservation technologies for Caribbean Tourist Facilities (CTF)

NASA Astrophysics Data System (ADS)

The primary objectives of the Caribbean Tourist Facilities (CTF) project were to develop and publish materials and conduct workshops on solar energy and conservation technologies that would directly address the needs and interests of tourist facilities in the Caribbean basin. Past contacts with the Caribbean and US tourist industries indicated that decision-makers remained unconvinced that renewable technologies could have a significant impact on development and operation costs or that renewable energy products and services suited their needs. In order to assure that the materials and programs developed were responsive to the Caribbean tourist industry and U.S. conservation and renewable energy industries, marketing research with potential end users and the organizations and associations that serve those users was included as an underlying task in the project. The tasks outlined in the CTF Statement of Work included conference planning, gathering of field data, development of educational materials, and conduct of workshop(s). In addition to providing a chronicle of the fulfillment of those tasks, this final report includes suggestions for distributing the documents developed during the project, venues for future workshops, and other technology transfer and market influence strategies.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The primary objectives of the Caribbean Tourist Facilities (CTF) project were to develop and publish materials and conduct workshops on solar energy and conservation technologies that would directly address the needs and interests of tourist facilities in the Caribbean basin. Past contacts with the Caribbean and US tourist industries indicated that decision-makers remained unconvinced that renewable technologies could have a significant impact on development and operation costs or that renewable energy products and services suited their needs. In order to assure that the materials and programs developed were responsive to the Caribbean tourist industry and US conservation and renewable energymore » industries, marketing research with potential end users and the organizations and associations that serve those users was included as an underlying task in the project. The tasks outlined in the CTF Statement of Work included conference planning, gathering of field data, development of educational materials, and conduct of workshop(s). In addition to providing a chronicle of the fulfillment of those tasks, this final report includes suggestions for distributing the documents developed during the project, venues for future workshops, and other technology transfer and market influence strategies. 3 refs.« less

A Manual Control Test for the Detection and Deterrence of Impaired Drivers

NASA Technical Reports Server (NTRS)

Stein, A. C.; Allen, R. W.; Jex, H. R.

1984-01-01

A brief manual control test and a decision strategy were developed, laboratory tested, and field validated which provide a means for detecting human operator impairment from alcohol or other drugs. The test requires the operator to stabilize progressively unstable controlled element dynamics. Control theory and experimental data verify that the human operator's control ability on this task is constrained by basic cybernetic characteristics, and that task performance is reliably affected by impairment effects on these characteristics. Assessment of human operator control ability is determined by a statistically based decision strategy. The operator is allowed several chances to exceed a preset pass criterion. Procedures are described for setting the pass criterion based on individual ability and a desired unimpaired failure rate. These procedures were field tested with apparatus installed in automobiles that were designed to discourage drunk drivers from operating their vehicles. This test program demonstrated that the control task and detection strategy could be applied in a practical setting to screen human operators for impairment in their basic cybernetic skills.

Strategic planning for the International Space Station

NASA Technical Reports Server (NTRS)

Griner, Carolyn S.

1990-01-01

The concept for utilization and operations planning for the International Space Station Freedom was developed in a NASA Space Station Operations Task Force in 1986. Since that time the concept has been further refined to definitize the process and products required to integrate the needs of the international user community with the operational capabilities of the Station in its evolving configuration. The keystone to the process is the development of individual plans by the partners, with the parameters and formats common to the degree that electronic communications techniques can be effectively utilized, while maintaining the proper level and location of configuration control. The integration, evaluation, and verification of the integrated plan, called the Consolidated Operations and Utilization Plan (COUP), is being tested in a multilateral environment to prove out the parameters, interfaces, and process details necessary to produce the first COUP for Space Station in 1991. This paper will describe the concept, process, and the status of the multilateral test case.

Improved Real-Time Monitoring Using Multiple Expert Systems

NASA Technical Reports Server (NTRS)

Schwuttke, Ursula M.; Angelino, Robert; Quan, Alan G.; Veregge, John; Childs, Cynthia

1993-01-01

Monitor/Analyzer of Real-Time Voyager Engineering Link (MARVEL) computer program implements combination of techniques of both conventional automation and artificial intelligence to improve monitoring of complicated engineering system. Designed to support ground-based operations of Voyager spacecraft, also adapted to other systems. Enables more-accurate monitoring and analysis of telemetry, enhances productivity of monitoring personnel, reduces required number of such personnel by performing routine monitoring tasks, and helps ensure consistency in face of turnover of personnel. Programmed in C language and includes commercial expert-system software shell also written in C.

Design, processing and testing of LSI arrays, hybrid microelectronics task

NASA Technical Reports Server (NTRS)

Himmel, R. P.; Stuhlbarg, S. M.; Ravetti, R. G.; Zulueta, P. J.; Rothrock, C. W.

1979-01-01

Mathematical cost models previously developed for hybrid microelectronic subsystems were refined and expanded. Rework terms related to substrate fabrication, nonrecurring developmental and manufacturing operations, and prototype production are included. Sample computer programs were written to demonstrate hybrid microelectric applications of these cost models. Computer programs were generated to calculate and analyze values for the total microelectronics costs. Large scale integrated (LST) chips utilizing tape chip carrier technology were studied. The feasibility of interconnecting arrays of LSU chips utilizing tape chip carrier and semiautomatic wire bonding technology was demonstrated.

Welding technology transfer task/laser based weld joint tracking system for compressor girth welds

NASA Technical Reports Server (NTRS)

Looney, Alan

1991-01-01

Sensors to control and monitor welding operations are currently being developed at Marshall Space Flight Center. The laser based weld bead profiler/torch rotation sensor was modified to provide a weld joint tracking system for compressor girth welds. The tracking system features a precision laser based vision sensor, automated two-axis machine motion, and an industrial PC controller. The system benefits are elimination of weld repairs caused by joint tracking errors which reduces manufacturing costs and increases production output, simplification of tooling, and free costly manufacturing floor space.

Quantum communication using a multiqubit entangled channel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghose, Shohini, E-mail: sghose@wlu.ca; Institute for Quantum Computing, University of Waterloo, Ontario; Hamel, Angele

We describe a protocol in which two senders each teleport a qubit to a receiver using a multiqubit entangled state. The multiqubit channel used for teleportation is genuinely 4-qubit entangled and is not equivalent to a product of maximally entangled Bell pairs under local unitary operations. We discuss a scenario in which both senders must participate for the qubits to be successfully teleported. Such an all-or-nothing scheme cannot be implemented with standard two-qubit entangled Bell pairs and can be useful for different communication and computing tasks.

Quantum communication using a multiqubit entangled channel

NASA Astrophysics Data System (ADS)

Ghose, Shohini; Hamel, Angele

2015-12-01

We describe a protocol in which two senders each teleport a qubit to a receiver using a multiqubit entangled state. The multiqubit channel used for teleportation is genuinely 4-qubit entangled and is not equivalent to a product of maximally entangled Bell pairs under local unitary operations. We discuss a scenario in which both senders must participate for the qubits to be successfully teleported. Such an all-or-nothing scheme cannot be implemented with standard two-qubit entangled Bell pairs and can be useful for different communication and computing tasks.

Using Multi-Core Systems for Rover Autonomy

NASA Technical Reports Server (NTRS)

Clement, Brad; Estlin, Tara; Bornstein, Benjamin; Springer, Paul; Anderson, Robert C.

2010-01-01

Task Objectives are: (1) Develop and demonstrate key capabilities for rover long-range science operations using multi-core computing, (a) Adapt three rover technologies to execute on SOA multi-core processor (b) Illustrate performance improvements achieved (c) Demonstrate adapted capabilities with rover hardware, (2) Targeting three high-level autonomy technologies (a) Two for onboard data analysis (b) One for onboard command sequencing/planning, (3) Technologies identified as enabling for future missions, (4)Benefits will be measured along several metrics: (a) Execution time / Power requirements (b) Number of data products processed per unit time (c) Solution quality

Space station operations task force. Panel 3 report: User development and integration

NASA Technical Reports Server (NTRS)

1987-01-01

The User Development and Integration Panel of the Space Station Operations Task Force was chartered to develop concepts relating to the operations of the Space Station manned base and the platforms, user accommodation and integration activities. The needs of the user community are addressed in the context with the mature operations phase of the Space Station. Issues addressed include space station pricing options, marketing strategies, payload selection and resource allocation options, and manifesting techniques.

[Chemical risk in farming].

PubMed

Moretto, Angelo

2013-01-01

The most important chemical risks in agriculture are plant protection products. Exposure evaluation in agriculture is not an easy task and cannot be carried out with the tools and methodologies of industrial exposures. However, toxicological studies on plant protection products, that are compulsory, provide a lot of useful information for actual risk assessment. Exposure evaluation can be carried out on the basis of exposure models and on semiquantitative measures based on the observation of the activity as it is carried our by the farmer. It is therefore possible to develop risk profiles that can guide exposure evaluation and health surveillance. Concentrated animal feeding operations are associated with several chemical risks including disinfectants, antibiotics, and gases such as ammonia and hydrogen sulfide, in addition to organic dusts and endotoxins.

Transfer of Decision Making and Farm Tasks from Father to Son in Father-and-Son Farming Arrangements. RS-51, August 1976.

ERIC Educational Resources Information Center

Coughenour, C. Milton; And Others

The study examined the division of decision-making and farm tasks in a joint father and son enterprise, the extent to which the decisions tended to be shared equally, and the extent to which the principal operator had responsibility for those tasks not shared. Data were collected in 1974 from fathers and sons who were joint operators of 145 farms…

NASA: Model development for human factors interfacing

NASA Technical Reports Server (NTRS)

Smith, L. L.

1984-01-01

The results of an intensive literature review in the general topics of human error analysis, stress and job performance, and accident and safety analysis revealed no usable techniques or approaches for analyzing human error in ground or space operations tasks. A task review model is described and proposed to be developed in order to reduce the degree of labor intensiveness in ground and space operations tasks. An extensive number of annotated references are provided.

Technical Manual for the Geospatial Stream Flow Model (GeoSFM)

USGS Publications Warehouse

Asante, Kwabena O.; Artan, Guleid A.; Pervez, Md Shahriar; Bandaragoda, Christina; Verdin, James P.

2008-01-01

The monitoring of wide-area hydrologic events requires the use of geospatial and time series data available in near-real time. These data sets must be manipulated into information products that speak to the location and magnitude of the event. Scientists at the U.S. Geological Survey Earth Resources Observation and Science (USGS EROS) Center have implemented a hydrologic modeling system which consists of an operational data processing system and the Geospatial Stream Flow Model (GeoSFM). The data processing system generates daily forcing evapotranspiration and precipitation data from various remotely sensed and ground-based data sources. To allow for rapid implementation in data scarce environments, widely available terrain, soil, and land cover data sets are used for model setup and initial parameter estimation. GeoSFM performs geospatial preprocessing and postprocessing tasks as well as hydrologic modeling tasks within an ArcView GIS environment. The integration of GIS routines and time series processing routines is achieved seamlessly through the use of dynamically linked libraries (DLLs) embedded within Avenue scripts. GeoSFM is run operationally to identify and map wide-area streamflow anomalies. Daily model results including daily streamflow and soil water maps are disseminated through Internet map servers, flood hazard bulletins and other media.

Thalamic deep brain stimulation decelerates automatic lexical activation.

PubMed

Ehlen, Felicitas; Vonberg, Isabelle; Tiedt, Hannes O; Horn, Andreas; Fromm, Ortwin; Kühn, Andrea A; Klostermann, Fabian

2017-02-01

Deep Brain Stimulation (DBS) of the thalamic ventral intermediate nucleus (VIM) is a therapeutic option for patients with essential tremor. Despite a generally low risk of side effects, declines in verbal fluency (VF) have previously been reported. We aimed to specify effects of VIM-DBS on major cognitive operations needed for VF task performance, represented by clusters and switches. Clusters are word production spurts, thought to arise from automatic activation of associated information pertaining to a given lexical field. Switches are slow word-to-word transitions, presumed to indicate controlled operations for stepping from one lexical field to another. Thirteen essential tremor patients with VIM-DBS performed verbal fluency tasks in their VIM-DBS ON and OFF conditions. Clusters and switches were formally defined by mathematical criteria. All results were compared to those of fifteen healthy control subjects, and significant OFF-ON-change scores were correlated to stimulation parameters. Patients produced fewer words than healthy controls. DBS ON compared to DBS OFF aggravated this deficit by prolonging the intervals between words within clusters, whereas switches remained unaffected. This stimulation effect correlated with more anterior electrode positions. VIM-DBS seems to influence word output dynamics during verbal fluency tasks on the level of word clustering. This suggests a perturbation of automatic lexical co-activation by thalamic stimulation, particularly if delivered relatively anteriorly. The findings are discussed in the context of the hypothesized role of the thalamus in lexical processing. Copyright © 2016 Elsevier Inc. All rights reserved.

New software solutions for analytical spectroscopists

NASA Astrophysics Data System (ADS)

Davies, Antony N.

1999-05-01

Analytical spectroscopists must be computer literate to effectively carry out the tasks assigned to them. This has often been resisted within organizations with insufficient funds to equip their staff properly, a lack of desire to deliver the essential training and a basic resistance amongst staff to learn the new techniques required for computer assisted analysis. In the past these problems were compounded by seriously flawed software which was being sold for spectroscopic applications. Owing to the limited market for such complex products the analytical spectroscopist often was faced with buying incomplete and unstable tools if the price was to remain reasonable. Long product lead times meant spectrometer manufacturers often ended up offering systems running under outdated and sometimes obscure operating systems. Not only did this mean special staff training for each instrument where the knowledge gained on one system could not be transferred to the neighbouring system but these spectrometers were often only capable of running in a stand-alone mode, cut-off from the rest of the laboratory environment. Fortunately a number of developments in recent years have substantially changed this depressing picture. A true multi-tasking operating system with a simple graphical user interface, Microsoft Windows NT4, has now been widely introduced into the spectroscopic computing environment which has provided a desktop operating system which has proved to be more stable and robust as well as requiring better programming techniques of software vendors. The opening up of the Internet has provided an easy way to access new tools for data handling and has forced a substantial re-think about results delivery (for example Chemical MIME types, IUPAC spectroscopic data exchange standards). Improved computing power and cheaper hardware now allows large spectroscopic data sets to be handled without too many problems. This includes the ability to carry out chemometric operations in minutes rather than hours. Fast networks now enable data analysis of even multi-dimensional spectroscopic data sets remote from the measuring instrument. A strong tendency to opt for a more unified graphical user interface which is substantially more user friendly allows even inexperienced users to rapidly get acquainted with even the complex mathematical analyses. Some examples of new spectroscopic software products will be given to demonstrate the aforesaid points and highlight the ease of integration into a modern analytical spectroscopy workplace.

Dashboard Task Monitor for Managing ATLAS User Analysis on the Grid

NASA Astrophysics Data System (ADS)

Sargsyan, L.; Andreeva, J.; Jha, M.; Karavakis, E.; Kokoszkiewicz, L.; Saiz, P.; Schovancova, J.; Tuckett, D.; Atlas Collaboration

2014-06-01

The organization of the distributed user analysis on the Worldwide LHC Computing Grid (WLCG) infrastructure is one of the most challenging tasks among the computing activities at the Large Hadron Collider. The Experiment Dashboard offers a solution that not only monitors but also manages (kill, resubmit) user tasks and jobs via a web interface. The ATLAS Dashboard Task Monitor provides analysis users with a tool that is independent of the operating system and Grid environment. This contribution describes the functionality of the application and its implementation details, in particular authentication, authorization and audit of the management operations.

Analytical study of electrical disconnect system for use on manned and unmanned missions

NASA Technical Reports Server (NTRS)

Rosener, A. A.; Lenda, J. A.; Trummer, R. O.

1976-01-01

The objective of this contract is to establish an optimum electrical disconnect system design(s) for use on manned and unmanned missions. The purpose of the disconnect system is to electrically mate and demate the spacecraft to subsystem module interfaces to accomplish orbital operations. The results of Task 1 and Task 2 of the effort are presented. Task 1 involves the definition of the functional, operational, and environmental requirements for the connector system to support the leading prototype candidate concepts. Task 2 involves the documentation review and survey of available existing connector designs.

The JPL telerobot operator control station. Part 2: Software

NASA Technical Reports Server (NTRS)

Kan, Edwin P.; Landell, B. Patrick; Oxenberg, Sheldon; Morimoto, Carl

1989-01-01

The Operator Control Station of the Jet Propulsion Laboratory (JPL)/NASA Telerobot Demonstrator System provides the man-machine interface between the operator and the system. It provides all the hardware and software for accepting human input for the direct and indirect (supervised) manipulation of the robot arms and tools for task execution. Hardware and software are also provided for the display and feedback of information and control data for the operator's consumption and interaction with the task being executed. The software design of the operator control system is discussed.

Developmental Inter-Relationships Among Concrete Operational Tasks: An Investigation of Piaget's Stage Concept

ERIC Educational Resources Information Center

Jamison, Wesley

1977-01-01

Two models of intertask relations, Wohlwill's divergent-decalage and reciprocal-interaction patterns, were evaluated for their fit to cross-classification tables which showed the joint classification of 101 children's performance on all possible pairs of eight concrete operational tasks. (SB)

Modeling and Design of an Electro-Rheological Fluid Based Haptic System for Tele-Operation of Space Robots

NASA Technical Reports Server (NTRS)

Mavroidis, Constantinos; Pfeiffer, Charles; Paljic, Alex; Celestino, James; Lennon, Jamie; Bar-Cohen, Yoseph

2000-01-01

For many years, the robotic community sought to develop robots that can eventually operate autonomously and eliminate the need for human operators. However, there is an increasing realization that there are some tasks that human can perform significantly better but, due to associated hazards, distance, physical limitations and other causes, only robot can be employed to perform these tasks. Remotely performing these types of tasks requires operating robots as human surrogates. While current "hand master" haptic systems are able to reproduce the feeling of rigid objects, they present great difficulties in emulating the feeling of remote/virtual stiffness. In addition, they tend to be heavy, cumbersome and usually they only allow limited operator workspace. In this paper a novel haptic interface is presented to enable human-operators to "feel" and intuitively mirror the stiffness/forces at remote/virtual sites enabling control of robots as human-surrogates. This haptic interface is intended to provide human operators intuitive feeling of the stiffness and forces at remote or virtual sites in support of space robots performing dexterous manipulation tasks (such as operating a wrench or a drill). Remote applications are referred to the control of actual robots whereas virtual applications are referred to simulated operations. The developed haptic interface will be applicable to IVA operated robotic EVA tasks to enhance human performance, extend crew capability and assure crew safety. The electrically controlled stiffness is obtained using constrained ElectroRheological Fluids (ERF), which changes its viscosity under electrical stimulation. Forces applied at the robot end-effector due to a compliant environment will be reflected to the user using this ERF device where a change in the system viscosity will occur proportionally to the force to be transmitted. In this paper, we will present the results of our modeling, simulation, and initial testing of such an electrorheological fluid (ERF) based haptic device.

An Intelligent Man-Machine Interface—Multi-Robot Control Adapted for Task Engagement Based on Single-Trial Detectability of P300

PubMed Central

Kirchner, Elsa A.; Kim, Su K.; Tabie, Marc; Wöhrle, Hendrik; Maurus, Michael; Kirchner, Frank

2016-01-01

Advanced man-machine interfaces (MMIs) are being developed for teleoperating robots at remote and hardly accessible places. Such MMIs make use of a virtual environment and can therefore make the operator immerse him-/herself into the environment of the robot. In this paper, we present our developed MMI for multi-robot control. Our MMI can adapt to changes in task load and task engagement online. Applying our approach of embedded Brain Reading we improve user support and efficiency of interaction. The level of task engagement was inferred from the single-trial detectability of P300-related brain activity that was naturally evoked during interaction. With our approach no secondary task is needed to measure task load. It is based on research results on the single-stimulus paradigm, distribution of brain resources and its effect on the P300 event-related component. It further considers effects of the modulation caused by a delayed reaction time on the P300 component evoked by complex responses to task-relevant messages. We prove our concept using single-trial based machine learning analysis, analysis of averaged event-related potentials and behavioral analysis. As main results we show (1) a significant improvement of runtime needed to perform the interaction tasks compared to a setting in which all subjects could easily perform the tasks. We show that (2) the single-trial detectability of the event-related potential P300 can be used to measure the changes in task load and task engagement during complex interaction while also being sensitive to the level of experience of the operator and (3) can be used to adapt the MMI individually to the different needs of users without increasing total workload. Our online adaptation of the proposed MMI is based on a continuous supervision of the operator's cognitive resources by means of embedded Brain Reading. Operators with different qualifications or capabilities receive only as many tasks as they can perform to avoid mental overload as well as mental underload. PMID:27445742

Proactive and coactive interference in age-related performance in a recognition-based operation span task.

PubMed

Zeintl, Melanie; Kliegel, Matthias

2010-01-01

Generally, older adults perform worse than younger adults in complex working memory span tasks. So far, it is unclear which processes mainly contribute to age-related differences in working memory span. The aim of the present study was to investigate age effects and the roles of proactive and coactive interference in a recognition-based version of the operation span task. Younger and older adults performed standard versions and distracter versions of the operation span task. At retrieval, participants had to recognize target words in word lists containing targets as well as proactive and/or coactive interference-related lures. Results show that, overall, younger adults outperformed older adults in the recognition of target words. Furthermore, analyses of error types indicate that, while younger adults were only affected by simultaneously presented distracter words, older adults had difficulties with both proactive and coactive interference. Results suggest that age effects in complex span tasks may not be mainly due to retrieval deficits in old age. Copyright 2009 S. Karger AG, Basel.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnstone, Peter; Jacobson, Arne; Mills, Evan

Creation of light for work, socializing, and general illumination is a fundamental application of technology around the world. For those who lack access to electricity, an emerging and diverse range of LED based lighting products hold promise for replacing and/or augmenting their current fuel-based lighting sources that are costly and dirty. Along with analysis of environmental factors, economic models for total cost-ofownership of LED lighting products are an important tool for studying the impacts of these products as they emerge in markets of developing countries. One important metric in those models is the minimum illuminance demanded by end-users for amore » given task before recharging the lamp or replacing batteries. It impacts the lighting service cost per unit time if charging is done with purchased electricity, batteries, or charging services. The concept is illustrated in figure 1: LED lighting products are generally brightest immediately after the battery is charged or replaced and the illuminance degrades as the battery is discharged. When a minimum threshold level of illuminance is reached, the operational time for the battery charge cycle is over. The cost to recharge depends on the method utilized; these include charging at a shop at a fixed price per charge, charging on personal grid connections, using solar chargers, and purchasing dry cell batteries. This Research Note reports on the observed"charge-triggering" illuminance level threshold for night market vendors who use LED lighting products to provide general and task oriented illumination. All the study participants charged with AC power, either at a fixed-price charge shop or with electricity at their home.« less

A framework of space weather satellite data pipeline

NASA Astrophysics Data System (ADS)

Ma, Fuli; Zou, Ziming

Various applications indicate a need of permanent space weather information. The diversity of available instruments enables a big variety of products. As an indispensable part of space weather satellite operation system, space weather data processing system is more complicated than before. The information handled by the data processing system has been used in more and more fields such as space weather monitoring and space weather prediction models. In the past few years, many satellites have been launched by China. The data volume downlinked by these satellites has achieved the so-called big data level and it will continue to grow fast in the next few years due to the implementation of many new space weather programs. Because of the huge amount of data, the current infrastructure is no longer incapable of processing data timely, so we proposed a new space weather data processing system (SWDPS) based on the architecture of cloud computing. Similar to Hadoop, SWDPS decomposes the tasks into smaller tasks which will be executed by many different work nodes. Control Center in SWDPS, just like NameNode and JobTracker within Hadoop which is the bond between the data and the cluster, will establish work plan for the cluster once a client submits data. Control Center will allocate node for the tasks and the monitor the status of all tasks. As the same of TaskTrakcer, Compute Nodes in SWDPS are the salves of Control Center which are responsible for calling the plugins(e.g., dividing and sorting plugins) to execute the concrete jobs. They will also manage all the tasks’ status and report them to Control Center. Once a task fails, a Compute Node will notify Control Center. Control Center decides what to do then; it may resubmit the job elsewhere, it may mark that specific record as something to avoid, and it may even blacklist the Compute Node as unreliable. In addition to these modules, SWDPS has a different module named Data Service which is used to provide file operations such as adding, deleting, modifying and querying for the clients. Beyond that Data Service can also split and combine files based on the timestamp of each record. SWDPS has been used for quite some time and it has been successfully dealt with many satellites, such as FY1C, FY1D, FY2A, FY2B, etc. The good performance in actual operation shows that SWDPS is stable and reliable.

Modified Universal Design Survey: Enhancing Operability of Launch Vehicle Ground Crew Worksites

NASA Technical Reports Server (NTRS)

Blume, Jennifer L.

2010-01-01

Operability is a driving requirement for next generation space launch vehicles. Launch site ground operations include numerous operator tasks to prepare the vehicle for launch or to perform preflight maintenance. Ensuring that components requiring operator interaction at the launch site are designed for optimal human use is a high priority for operability. To promote operability, a Design Quality Evaluation Survey based on Universal Design framework was developed to support Human Factors Engineering (HFE) evaluation for NASA s launch vehicles. Universal Design per se is not a priority for launch vehicle processing however; applying principles of Universal Design will increase the probability of an error free and efficient design which promotes operability. The Design Quality Evaluation Survey incorporates and tailors the seven Universal Design Principles and adds new measures for Safety and Efficiency. Adapting an approach proven to measure Universal Design Performance in Product, each principle is associated with multiple performance measures which are rated with the degree to which the statement is true. The Design Quality Evaluation Survey was employed for several launch vehicle ground processing worksite analyses. The tool was found to be most useful for comparative judgments as opposed to an assessment of a single design option. It provided a useful piece of additional data when assessing possible operator interfaces or worksites for operability.

Influence of a new generation of operations support systems on current spacecraft operations philosophy: The users feedback

NASA Technical Reports Server (NTRS)

Darroy, Jean Michel

1993-01-01

Current trends in the spacecraft mission operations area (spacecraft & mission complexity, project duration, required flexibility are requiring a breakthrough for what concerns philosophy, organization, and support tools. A major evolution is related to space operations 'informationalization', i.e adding to existing operations support & data processing systems a new generation of tools based on advanced information technologies (object-oriented programming, artificial intelligence, data bases, hypertext) that automate, at least partially, operations tasks that used be performed manually (mission & project planning/scheduling, operations procedures elaboration & execution, data analysis & failure diagnosis). All the major facets of this 'informationalization' are addressed at MATRA MARCONI SPACE, operational applications were fielded and generic products are becoming available. These various applications have generated a significant feedback from the users (at ESA, CNES, ARIANESPACE, MATRA MARCONI SPACE), which is now allowing us to precisely measure how the deployment of this new generation of tools, that we called OPSWARE, can 'reengineer' current spacecraft mission operations philosophy, how it can make space operations faster, better, and cheaper. This paper can be considered as an update of the keynote address 'Knowledge-Based Systems for Spacecraft Control' presented during the first 'Ground Data Systems for Spacecraft Control' conference in Darmstadt, June 1990, with a special emphasis on these last two years users feedback.

The JPL/KSC telerobotic inspection demonstration

NASA Technical Reports Server (NTRS)

Mittman, David; Bon, Bruce; Collins, Carol; Fleischer, Gerry; Litwin, Todd; Morrison, Jack; Omeara, Jacquie; Peters, Stephen; Brogdon, John; Humeniuk, Bob

1990-01-01

An ASEA IRB90 robotic manipulator with attached inspection cameras was moved through a Space Shuttle Payload Assist Module (PAM) Cradle under computer control. The Operator and Operator Control Station, including graphics simulation, gross-motion spatial planning, and machine vision processing, were located at JPL. The Safety and Support personnel, PAM Cradle, IRB90, and image acquisition system, were stationed at the Kennedy Space Center (KSC). Images captured at KSC were used both for processing by a machine vision system at JPL, and for inspection by the JPL Operator. The system found collision-free paths through the PAM Cradle, demonstrated accurate knowledge of the location of both objects of interest and obstacles, and operated with a communication delay of two seconds. Safe operation of the IRB90 near Shuttle flight hardware was obtained both through the use of a gross-motion spatial planner developed at JPL using artificial intelligence techniques, and infrared beams and pressure sensitive strips mounted to the critical surfaces of the flight hardward at KSC. The Demonstration showed that telerobotics is effective for real tasks, safe for personnel and hardware, and highly productive and reliable for Shuttle payload operations and Space Station external operations.

Time-critical multirate scheduling using contemporary real-time operating system services

NASA Technical Reports Server (NTRS)

Eckhardt, D. E., Jr.

1983-01-01

Although real-time operating systems provide many of the task control services necessary to process time-critical applications (i.e., applications with fixed, invariant deadlines), it may still be necessary to provide a scheduling algorithm at a level above the operating system in order to coordinate a set of synchronized, time-critical tasks executing at different cyclic rates. The scheduling requirements for such applications and develops scheduling algorithms using services provided by contemporary real-time operating systems.

Evaluating the effect of distractions in the operating room on clinical decision-making and patient safety.

PubMed

Murji, Ally; Luketic, Lea; Sobel, Mara L; Kulasegaram, Kulamakan Mahan; Leyland, Nicholas; Posner, Glenn

2016-10-01

Answering telephone calls and pagers is common distraction in the operating room. We sought to evaluate the impact of distractions on patient care by (1) assessing the accuracy and safety of responses to clinical questions posed to a surgeon while operating and (2) determining whether pager distractions affect simulation-based surgical performance. We conducted a randomized crossover study of obstetrics and gynecology residents. After studying a patient sign-out list, subjects performed a virtual salpingectomy. They were randomized to a distraction phase followed by quiet phase or vice versa. In the distraction phase, a pager beeped and subjects were asked questions based on the sign-out list. Accuracy of responses and the number of unsafe responses were recorded. In the quiet phase, trainees performed the task uninterrupted. Measures of surgical performance were successful task completion, time to task completion and operative blood loss. The mean score for correct responses to clinical questions during the distracted phase was 80 % (SD ±14 %). Nineteen residents (63 %) made at least 1 unsafe clinical decision while operating on the simulator (range 0-3). Subjects were more likely to successfully complete the surgical task in the allotted time under the quiet compared to distraction condition (OR 11.3, p = 0.03). There was no difference between the conditions in paired analysis for mean time (seconds) to task completion [426 (SD 133) vs. 440 (SD 186), p = 0.61] and mean operative blood loss (mL) [73.14 (SD 106) vs. 112.70 (SD 358), p = 0.47]. Distractions in the operating room may have a profound impact on patient safety on the wards. While multitasking in a simulated setting, the majority of residents made at least one unsafe clinical decision. Pager distractions also hindered surgical residents' ability to complete a simulated laparoscopic task in the allotted time without affecting other variables of surgical performance.

Performing a global barrier operation in a parallel computer

DOEpatents

Archer, Charles J; Blocksome, Michael A; Ratterman, Joseph D; Smith, Brian E

2014-12-09

Executing computing tasks on a parallel computer that includes compute nodes coupled for data communications, where each compute node executes tasks, with one task on each compute node designated as a master task, including: for each task on each compute node until all master tasks have joined a global barrier: determining whether the task is a master task; if the task is not a master task, joining a single local barrier; if the task is a master task, joining the global barrier and the single local barrier only after all other tasks on the compute node have joined the single local barrier.

29 CFR 1918.92 - Illumination.

Code of Federal Regulations, 2011 CFR

2011-07-01

... operations, illumination for cargo transfer operations shall be of a minimum light intensity of five foot-candles (54 lux). Where work tasks require more light to be performed safely, supplemental lighting shall... surface, in the plane in which the task/working surface is present. (c) Arrangement of lights. Lights...

Cognitive Requirements for Small Unit Leaders in Military Operations in Urban Terrain

DTIC Science & Technology

1998-09-01

operations specifically. A cognitive task analysis , based on in depth interviews with subject matter experts (n=7), was conducted to expose the...process. The findings of the cognitive task analysis guided the development of training recommendations, particularly the need for a scenario based

Extended System Operations Studies for Automated Guideway Transit Systems : Plan for Task 5--DPM Failure Management

DOT National Transportation Integrated Search

1981-06-01

The purpose of Task 5 in the Extended System Operations Studies Project, DPM Failure Management, is to enhance the capabilities of the Downtown People Mover Simulation (DPMS) and the Discrete Event Simulation Model (DESM) by increasing the failure mo...

Housing and testing in mixed-sex rooms increases motivation and accuracy during operant testing in both male and female mice.

PubMed

Lloyd, Kelsey R; Yaghoubi, Sarah K; Makinson, Ryan A; McKee, Sarah E; Reyes, Teresa M

2018-04-01

Operant behavior tasks are widely used in neuroscience research, but little is known about how variables such as housing and testing conditions affect rodent operant performance. We have previously observed differences in operant performance in male and female mice depending on whether mice were housed and tested in rooms containing only one sex versus rooms containing both sexes. Here, male and female mice in either single-sex or mixed sex housing rooms were trained on fixed ratio 1 (FR1) and progressive ratio (PR) tasks. For both sexes, animals in the mixed sex room had more accurate performance in FR1 and were more motivated in the PR task. We then moved the single sex housed animals to the mixed sex room and vice versa. Animals that started in mixed sex housing had no change to PR, but both sexes who started in single sex housing were more motivated after the switch. Additionally, the females that moved into single-sex housing performed less accurately in FR1. We conclude that housing and testing conditions can affect performance on FR1 and PR tasks. As these tasks are commonly used as training steps to more complex tasks, housing and testing conditions should be carefully considered during experiment design and reported in publications. Copyright © 2018 Elsevier Inc. All rights reserved.

Performance evaluation of a six-axis generalized force-reflecting teleoperator

NASA Technical Reports Server (NTRS)

Hannaford, B.; Wood, L.; Guggisberg, B.; Mcaffee, D.; Zak, H.

1989-01-01

Work in real-time distributed computation and control has culminated in a prototype force-reflecting telemanipulation system having a dissimilar master (cable-driven, force-reflecting hand controller) and a slave (PUMA 560 robot with custom controller), an extremely high sampling rate (1000 Hz), and a low loop computation delay (5 msec). In a series of experiments with this system and five trained test operators covering over 100 hours of teleoperation, performance was measured in a series of generic and application-driven tasks with and without force feedback, and with control shared between teleoperation and local sensor referenced control. Measurements defining task performance included 100-Hz recording of six-axis force/torque information from the slave manipulator wrist, task completion time, and visual observation of predefined task errors. The task consisted of high precision peg-in-hole insertion, electrical connectors, velcro attach-de-attach, and a twist-lock multi-pin connector. Each task was repeated three times under several operating conditions: normal bilateral telemanipulation, forward position control without force feedback, and shared control. In shared control, orientation was locally servo controlled to comply with applied torques, while translation was under operator control. All performance measures improved as capability was added along a spectrum of capabilities ranging from pure position control through force-reflecting teleoperation and shared control. Performance was optimal for the bare-handed operator.

Human-Automation Integration: Principle and Method for Design and Evaluation

NASA Technical Reports Server (NTRS)

Billman, Dorrit; Feary, Michael

2012-01-01

Future space missions will increasingly depend on integration of complex engineered systems with their human operators. It is important to ensure that the systems that are designed and developed do a good job of supporting the needs of the work domain. Our research investigates methods for needs analysis. We included analysis of work products (plans for regulation of the space station) as well as work processes (tasks using current software), in a case study of Attitude Determination and Control Officers (ADCO) planning work. This allows comparing how well different designs match the structure of the work to be supported. Redesigned planning software that better matches the structure of work was developed and experimentally assessed. The new prototype enabled substantially faster and more accurate performance in plan revision tasks. This success suggests the approach to needs assessment and use in design and evaluation is promising, and merits investigatation in future research.

High Availability Applications for NOMADS at the NOAA Web Operations Center Aimed at Providing Reliable Real Time Access to Operational Model Data

NASA Astrophysics Data System (ADS)

Alpert, J. C.; Rutledge, G.; Wang, J.; Freeman, P.; Kang, C. Y.

2009-05-01

The NOAA Operational Modeling Archive Distribution System (NOMADS) is now delivering high availability services as part of NOAA's official real time data dissemination at its Web Operations Center (WOC). The WOC is a web service used by all organizational units in NOAA and acts as a data repository where public information can be posted to a secure and scalable content server. A goal is to foster collaborations among the research and education communities, value added retailers, and public access for science and development efforts aimed at advancing modeling and GEO-related tasks. The services used to access the operational model data output are the Open-source Project for a Network Data Access Protocol (OPeNDAP), implemented with the Grid Analysis and Display System (GrADS) Data Server (GDS), and applications for slicing, dicing and area sub-setting the large matrix of real time model data holdings. This approach insures an efficient use of computer resources because users transmit/receive only the data necessary for their tasks including metadata. Data sets served in this way with a high availability server offer vast possibilities for the creation of new products for value added retailers and the scientific community. New applications to access data and observations for verification of gridded model output, and progress toward integration with access to conventional and non-conventional observations will be discussed. We will demonstrate how users can use NOMADS services to repackage area subsets either using repackaging of GRIB2 files, or values selected by ensemble component, (forecast) time, vertical levels, global horizontal location, and by variable, virtually a 6- Dimensional analysis services across the internet.

Orbit transfer rocket engine technology program

NASA Technical Reports Server (NTRS)

Gustafson, N. B.; Harmon, T. J.

1993-01-01

An advanced near term (1990's) space-based Orbit Transfer Vehicle Engine (OTVE) system was designed, and the technologies applicable to its construction, maintenance, and operations were developed under Tasks A through F of the Orbit Transfer Rocket Engine Technology Program. Task A was a reporting task. In Task B, promising OTV turbomachinery technologies were explored: two stage partial admission turbines, high velocity ratio diffusing crossovers, soft wear ring seals, advanced bearing concepts, and a rotordynamic analysis. In Task C, a ribbed combustor design was developed. Possible rib and channel geometries were chosen analytically. Rib candidates were hot air tested and laser velocimeter boundary layer analyses were conducted. A channel geometry was also chosen on the basis of laser velocimeter data. To verify the predicted heat enhancement effects, a ribbed calorimeter spool was hot fire tested. Under Task D, the optimum expander cycle engine thrust, performance and envelope were established for a set of OTV missions. Optimal nozzle contours and quick disconnects for modularity were developed. Failure Modes and Effects Analyses, maintenance and reliability studies and component study results were incorporated into the engine system. Parametric trades on engine thrust, mixture ratio, and area ratio were also generated. A control system and the health monitoring and maintenance operations necessary for a space-based engine were outlined in Task E. In addition, combustor wall thickness measuring devices and a fiberoptic shaft monitor were developed. These monitoring devices were incorporated into preflight engine readiness checkout procedures. In Task F, the Integrated Component Evaluator (I.C.E.) was used to demonstrate performance and operational characteristics of an advanced expander cycle engine system and its component technologies. Sub-system checkouts and a system blowdown were performed. Short transitions were then made into main combustor ignition and main stage operation.

Fault diagnosis in orbital refueling operations

NASA Technical Reports Server (NTRS)

Boy, Guy A.

1988-01-01

Usually, operation manuals are provided for helping astronauts during space operations. These manuals include normal and malfunction procedures. Transferring operation manual knowledge into a computerized form is not a trivial task. This knowledge is generally written by designers or operation engineers and is often quite different from the user logic. The latter is usually a compiled version of the former. Experiments are in progress to assess the user logic. HORSES (Human - Orbital Refueling System - Expert System) is an attempt to include both of these logics in the same tool. It is designed to assist astronauts during monitoring and diagnosis tasks. Basically, HORSES includes a situation recognition level coupled to an analytical diagnoser, and a meta-level working on both of the previous levels. HORSES is a good tool for modeling task models and is also more broadly useful for knowledge design. The presentation is represented by abstract and overhead visuals only.