Neural fraud detection in credit card operations.

PubMed

Dorronsoro, J R; Ginel, F; Sgnchez, C; Cruz, C S

1997-01-01

This paper presents an online system for fraud detection of credit card operations based on a neural classifier. Since it is installed in a transactional hub for operation distribution, and not on a card-issuing institution, it acts solely on the information of the operation to be rated and of its immediate previous history, and not on historic databases of past cardholder activities. Among the main characteristics of credit card traffic are the great imbalance between proper and fraudulent operations, and a great degree of mixing between both. To ensure proper model construction, a nonlinear version of Fisher's discriminant analysis, which adequately separates a good proportion of fraudulent operations away from other closer to normal traffic, has been used. The system is fully operational and currently handles more than 12 million operations per year with very satisfactory results.

21 CFR 110.20 - Plant and grounds.

Code of Federal Regulations, 2011 CFR

2011-04-01

... filth, or providing a breeding place for pests. (4) Operating systems for waste treatment and disposal... controls and operating practices or effective design, including the separation of operations in which..., enclosed systems, or other effective means. (3) Permit the taking of proper precautions to protect food in...

21 CFR 110.20 - Plant and grounds.

Code of Federal Regulations, 2014 CFR

2014-04-01

... filth, or providing a breeding place for pests. (4) Operating systems for waste treatment and disposal... controls and operating practices or effective design, including the separation of operations in which..., enclosed systems, or other effective means. (3) Permit the taking of proper precautions to protect food in...

21 CFR 110.20 - Plant and grounds.

Code of Federal Regulations, 2013 CFR

2013-04-01

... filth, or providing a breeding place for pests. (4) Operating systems for waste treatment and disposal... controls and operating practices or effective design, including the separation of operations in which..., enclosed systems, or other effective means. (3) Permit the taking of proper precautions to protect food in...

Pressure Safety: Advanced Live 11459

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glass, George

Many Los Alamos National Laboratory (LANL) operations use pressure equipment and systems. Failure to follow proper procedures when designing or operating pressure systems can result in injuries to personnel and damage to equipment and/or the environment. This manual presents an overview of the requirements and recommendations that address the safe design and operation of pressure systems at LANL.

40 CFR 86.010-2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... diagnostics, means verifying that a component and/or system that receives information from a control computer... maintained. In general, limp-home operation implies that a component or system is not operating properly or... cannot be erased through human interaction with the OBD system or any onboard computer. Potential...

40 CFR 86.010-2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... diagnostics, means verifying that a component and/or system that receives information from a control computer... maintained. In general, limp-home operation implies that a component or system is not operating properly or... cannot be erased through human interaction with the OBD system or any onboard computer. Potential...

40 CFR 86.010-2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... diagnostics, means verifying that a component and/or system that receives information from a control computer... maintained. In general, limp-home operation implies that a component or system is not operating properly or... cannot be erased through human interaction with the OBD system or any onboard computer. Potential...

40 CFR 86.010-2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... diagnostics, means verifying that a component and/or system that receives information from a control computer... maintained. In general, limp-home operation implies that a component or system is not operating properly or... cannot be erased through human interaction with the OBD system or any onboard computer. Potential...

40 CFR 86.010-2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... diagnostics, means verifying that a component and/or system that receives information from a control computer... maintained. In general, limp-home operation implies that a component or system is not operating properly or... cannot be erased through human interaction with the OBD system or any onboard computer. Potential...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

47 CFR 74.634 - Remote control operation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... control system must be designed, installed, and protected so that the transmitter can only be activated or... ensure proper operation. (3) The remote control system must be designed to prevent inadvertent...

7 CFR 1717.652 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., all investments properly recorded on the borrower's books and records in investment accounts as those.... Operating DSC means Operating Debt Service Coverage (ODSC) of the borrower's electric system calculated as...

Ideas that Work!. Retuning the Building Automation System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parker, Steven

A building automation system (BAS) can save considerable energy by effectively and efficiently operating building energy systems (fans, pumps, chillers boilers, etc.), but only when the BAS is properly set up and operated. Tuning, or retuning, the BAS is a cost effective process worthy of your time and attention.

Maneuver Classification for Aircraft Fault Detection

NASA Technical Reports Server (NTRS)

Oza, Nikunj C.; Tumer, Irem Y.; Tumer, Kagan; Huff, Edward M.

2003-01-01

Automated fault detection is an increasingly important problem in aircraft maintenance and operation. Standard methods of fault detection assume the availability of either data produced during all possible faulty operation modes or a clearly-defined means to determine whether the data provide a reasonable match to known examples of proper operation. In the domain of fault detection in aircraft, identifying all possible faulty and proper operating modes is clearly impossible. We envision a system for online fault detection in aircraft, one part of which is a classifier that predicts the maneuver being performed by the aircraft as a function of vibration data and other available data. To develop such a system, we use flight data collected under a controlled test environment, subject to many sources of variability. We explain where our classifier fits into the envisioned fault detection system as well as experiments showing the promise of this classification subsystem.

40 CFR 86.005-17 - On-board diagnostics.

Code of Federal Regulations, 2013 CFR

2013-07-01

... other available operating parameters), and functionality checks for computer output components (proper... considered acceptable. (e) Storing of computer codes. The OBD system shall record and store in computer... monitors that can be considered continuously operating monitors (e.g., misfire monitor, fuel system monitor...

40 CFR 86.005-17 - On-board diagnostics.

Code of Federal Regulations, 2012 CFR

2012-07-01

... other available operating parameters), and functionality checks for computer output components (proper... considered acceptable. (e) Storing of computer codes. The OBD system shall record and store in computer... monitors that can be considered continuously operating monitors (e.g., misfire monitor, fuel system monitor...

47 CFR 78.51 - Remote control operation.

Code of Federal Regulations, 2014 CFR

2014-10-01

... control system shall be installed and protected in a manner designed to prevent tampering or operation by... transmissions and a carrier operated device which will give a continuous visual indication whenever the... necessary to insure proper operation. (4) The control circuits shall be so designed and installed that short...

47 CFR 78.51 - Remote control operation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... control system shall be installed and protected in a manner designed to prevent tampering or operation by... transmissions and a carrier operated device which will give a continuous visual indication whenever the... necessary to insure proper operation. (4) The control circuits shall be so designed and installed that short...

40 CFR 142.307 - What terms and conditions must be included in a small system variance?

Code of Federal Regulations, 2010 CFR

2010-07-01

... that may affect proper and effective operation and maintenance of the technology; (2) Monitoring... effective installation, operation and maintenance of the applicable small system variance technology in... health, which may include: (i) Public education requirements; and (ii) Source water protection...

29 CFR 1918.86 - Roll-on roll-off (Ro-Ro) operations (see also § 1918.2, Ro-Ro operations, and § 1918.25).

Code of Federal Regulations, 2010 CFR

2010-07-01

..., Ro-Ro operations, and § 1918.25). 9 [Reserved] (a) Traffic control system. An organized system of... simultaneous use of the ramp by vehicles and pedestrians. (d) Ramp maintenance. Ramps shall be properly...: (1) Sufficient power to ascend ramp inclines safely; and (2) Sufficient braking capacity to descend...

47 CFR 74.434 - Remote control operation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false Remote control operation. 74.434 Section 74.434 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... functions to permit proper operation of the station. (b) A remote control system must be designed, installed...

47 CFR 74.434 - Remote control operation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 4 2012-10-01 2012-10-01 false Remote control operation. 74.434 Section 74.434 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... functions to permit proper operation of the station. (b) A remote control system must be designed, installed...

47 CFR 74.434 - Remote control operation.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false Remote control operation. 74.434 Section 74.434 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... functions to permit proper operation of the station. (b) A remote control system must be designed, installed...

47 CFR 74.434 - Remote control operation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Remote control operation. 74.434 Section 74.434 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... functions to permit proper operation of the station. (b) A remote control system must be designed, installed...

47 CFR 74.434 - Remote control operation.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 4 2013-10-01 2013-10-01 false Remote control operation. 74.434 Section 74.434 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO... functions to permit proper operation of the station. (b) A remote control system must be designed, installed...

Causes of Indoor Air Quality Problems in Schools: Summary of Scientific Research. Revised Edition.

ERIC Educational Resources Information Center

Bayer, Charlene W.; Crow, Sidney A.; Fischer, John

Understanding the primary causes of indoor air quality (IAQ) problems and how controllable factors--proper heating, ventilation and air-conditioning (HVAC) system design, allocation of adequate outdoor air, proper filtration, effective humidity control, and routine maintenance--can avert problems may help all building owners, operators, and…

The promise--and peril--of integrated cost systems.

PubMed

Cooper, R; Kaplan, R S

1998-01-01

Recent advances in managerial accounting have helped executives get the information they need to make good strategic decisions. But today's enterprise resource planning systems promise even greater benefits--the chance to integrate activity-based costing, operational-control, and financial reporting systems. But managers need to approach integration very thoughtfully, or they could end up with a system that drives decision making in the wrong direction. Operational-control and ABC systems have fundamentally different purposes. Their requirements for accuracy, timeliness, and aggregation are so different that no single, fully integrated approach can be adequate for both purposes. If an integrated system used real-time cost data instead of standard rates in its ABC subsystem, for example, the result would be dangerously distorted messages about individual product profitability--and that's precisely the problem ABC systems were originally designed to address. Proper linkage and feedback between the two systems is possible, however. Through activity-based budgeting, the ABC system is linked directly to operations control: managers can determine the supply and practical capacity of resources in forthcoming periods. Linking operational control to ABC is also possible. The activity-based portion of an operational control system collects information that, while it mustn't be fed directly into the activity-based strategic cost system, can be extremely useful once it's been properly analyzed. Finally, ABC and operational control can be linked to financial reporting to generate cost of goods sold and inventory valuations--but again, with precautions.

Evaluation of VHF-FM Shore-Based Direction Finding Triangulation System in Massachusetts Bay Area

DOT National Transportation Integrated Search

1983-06-01

The evaluation consisted of the following phases: (1) System definition and site selection; System calibration; Operational evaluation; Cost/benefit analysis. It was concluded that properly implemented shore-based direction finding systems in either ...

29 CFR 1910.37 - Maintenance, safeguards, and operational features for exit routes.

Code of Federal Regulations, 2010 CFR

2010-07-01

...., sprinkler systems, alarm systems, fire doors, exit lighting) must be in proper working order at all times... maintain an operable employee alarm system that has a distinctive signal to warn employees of fire or other...” not less than three-fourths of an inch (1.9 cm) wide. (c) The fire retardant properties of paints or...

29 CFR 1910.37 - Maintenance, safeguards, and operational features for exit routes.

Code of Federal Regulations, 2011 CFR

2011-07-01

...., sprinkler systems, alarm systems, fire doors, exit lighting) must be in proper working order at all times... maintain an operable employee alarm system that has a distinctive signal to warn employees of fire or other...” not less than three-fourths of an inch (1.9 cm) wide. (c) The fire retardant properties of paints or...

29 CFR 1910.37 - Maintenance, safeguards, and operational features for exit routes.

Code of Federal Regulations, 2014 CFR

2014-07-01

...., sprinkler systems, alarm systems, fire doors, exit lighting) must be in proper working order at all times... maintain an operable employee alarm system that has a distinctive signal to warn employees of fire or other...” not less than three-fourths of an inch (1.9 cm) wide. (c) The fire retardant properties of paints or...

29 CFR 1910.37 - Maintenance, safeguards, and operational features for exit routes.

Code of Federal Regulations, 2013 CFR

2013-07-01

...., sprinkler systems, alarm systems, fire doors, exit lighting) must be in proper working order at all times... maintain an operable employee alarm system that has a distinctive signal to warn employees of fire or other...” not less than three-fourths of an inch (1.9 cm) wide. (c) The fire retardant properties of paints or...

AGARD Flight Test Techniques Series. Volume 8. Flight Testing under Extreme Environmental Conditions

DTIC Science & Technology

1988-01-01

gravity control system operation. The overall objective of fuel system tests is to determine whether the system functions properly at all conditions both... gravity . 3.3.4 Hydraulic System The functional adequacy of the hydraulic system should be evaluated by monitoring operating system temperatures and...mechanical or gravity function of the crew ladder should be evaluated. The ladder should be exposed to freasing rain and icing to evaluate the non

Temperature Control. Honeywell Planning Guide.

ERIC Educational Resources Information Center

Honeywell, Inc., Minneapolis, Minn.

Presents planning considerations in selecting proper temperature control systems. Various aspects are discussed including--(1) adequate environmental control, (2) adequate control area, (3) control system design, (4) operators rate their systems, (5) type of control components, (6) basic control system, (7) automatic control systems, and (8)…

Operation and Maintenance of Wastewater Collection Systems. Volume I. Third Edition. A Field Study Training Program.

ERIC Educational Resources Information Center

California State Univ., Sacramento. Dept. of Civil Engineering.

Proper installations, inspections, operations, maintenance and repairs of wastewater collection, conveyance and treatment facilities have a significant impact on the operation and maintenance costs, and the effectiveness of these facilities. This manual is the first volume of a two-part program designed to provide wastewater collection system…

A Homeowner's Guide to Septic Systems.

ERIC Educational Resources Information Center

Sponenberg, Torsten D.; And Others

This booklet provides basic information on septic system use and maintenance. Written for current and prospective homeowners, it offers guidelines for proper operation of household septic systems. In addition, (1) components of individual systems are diagrammatically explained; (2) suggestions for maintenance are outlined; (3) problem areas and…

48 CFR 970.5232-7 - Financial management system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... maintain and administer a financial management system that is suitable to provide proper accounting in... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Financial management... for Management and Operating Contracts 970.5232-7 Financial management system. As prescribed in 970...

14 CFR 25.952 - Fuel system analysis and test.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System § 25.952 Fuel system analysis and test. (a) Proper fuel system functioning under all probable operating conditions must be shown... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel system analysis and test. 25.952...

14 CFR 25.952 - Fuel system analysis and test.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System § 25.952 Fuel system analysis and test. (a) Proper fuel system functioning under all probable operating conditions must be shown... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel system analysis and test. 25.952...

14 CFR 25.952 - Fuel system analysis and test.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System § 25.952 Fuel system analysis and test. (a) Proper fuel system functioning under all probable operating conditions must be shown... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Fuel system analysis and test. 25.952...

14 CFR 25.952 - Fuel system analysis and test.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System § 25.952 Fuel system analysis and test. (a) Proper fuel system functioning under all probable operating conditions must be shown... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Fuel system analysis and test. 25.952...

14 CFR 25.952 - Fuel system analysis and test.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System § 25.952 Fuel system analysis and test. (a) Proper fuel system functioning under all probable operating conditions must be shown... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel system analysis and test. 25.952...

STRS Radio Service Software for NASA's SCaN Testbed

NASA Technical Reports Server (NTRS)

Mortensen, Dale J.; Bishop, Daniel Wayne; Chelmins, David T.

2012-01-01

NASAs Space Communication and Navigation(SCaN) Testbed was launched to the International Space Station in 2012. The objective is to promote new software defined radio technologies and associated software application reuse, enabled by this first flight of NASAs Space Telecommunications Radio System(STRS) architecture standard. Pre-launch testing with the testbeds software defined radios was performed as part of system integration. Radio services for the JPL SDR were developed during system integration to allow the waveform application to operate properly in the space environment, especially considering thermal effects. These services include receiver gain control, frequency offset, IQ modulator balance, and transmit level control. Development, integration, and environmental testing of the radio services will be described. The added software allows the waveform application to operate properly in the space environment, and can be reused by future experimenters testing different waveform applications. Integrating such services with the platform provided STRS operating environment will attract more users, and these services are candidates for interface standardization via STRS.

STRS Radio Service Software for NASA's SCaN Testbed

NASA Technical Reports Server (NTRS)

Mortensen, Dale J.; Bishop, Daniel Wayne; Chelmins, David T.

2013-01-01

NASA's Space Communication and Navigation(SCaN) Testbed was launched to the International Space Station in 2012. The objective is to promote new software defined radio technologies and associated software application reuse, enabled by this first flight of NASA's Space Telecommunications Radio System (STRS) architecture standard. Pre-launch testing with the testbed's software defined radios was performed as part of system integration. Radio services for the JPL SDR were developed during system integration to allow the waveform application to operate properly in the space environment, especially considering thermal effects. These services include receiver gain control, frequency offset, IQ modulator balance, and transmit level control. Development, integration, and environmental testing of the radio services will be described. The added software allows the waveform application to operate properly in the space environment, and can be reused by future experimenters testing different waveform applications. Integrating such services with the platform provided STRS operating environment will attract more users, and these services are candidates for interface standardization via STRS.

Alleviating line overload by line switching

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, H.E.

1988-01-01

Traditionally, the method used by power system dispatchers to reduce or to eliminate line overload conditions has been to shift generation. Such shifts are generally in conflict with the carefully considered economic dispatch of generation. A proper generation schedule has taken into account many factors, such as generator limits, transmission penalties, incremental costs, var support, and system security. Any deviation from this schedule results in increased production cost. Recently, consideration has been given to alleviating line overloads by line switching. In many situations, line switching does not greatly change the transmission penalty factors and, therefore, can be undertaken without seriouslymore » affecting the economic dispatch. It would be convenient for system operators to have a fast, easy-to-operate computer and program available for the evaluation of the efficacy of a line removal (or addition) in dealing with an overload. It is imperative that the operator be properly advised, that a certain line switching reduces the overload and not aggravate the condition. After it has been determined that a line opening (or closing) produces the desired effect, the operator still must assess the consequence of such switching on system security before actually taking such action.« less

The assessment of exploitation process of power for access control system

NASA Astrophysics Data System (ADS)

Wiśnios, Michał; Paś, Jacek

2017-10-01

The safety of public utility facilities is a function not only of effectiveness of the electronic safety systems, used for protection of property and persons, but it also depends on the proper functioning of their power supply systems. The authors of the research paper analysed the power supply systems, which are used in buildings for the access control system that is integrated with the closed-circuit TV. The Access Control System is a set of electronic, electromechanical and electrical devices and the computer software controlling the operation of the above-mentioned elements, which is aimed at identification of people, vehicles allowed to cross the boundary of the reserved area, to prevent from crossing the reserved area and to generate the alarm signal informing about the attempt of crossing by an unauthorised entity. The industrial electricity with appropriate technical parameters is a basis of proper functioning of safety systems. Only the electricity supply to the systems is not equivalent to the operation continuity provision. In practice, redundant power supply systems are used. In the carried out reliability analysis of the power supply system, various power circuits of the system were taken into account. The reliability and operation requirements for this type of system were also included.

Gas analysis system for the Eight Foot High Temperature Tunnel

NASA Technical Reports Server (NTRS)

Leighty, Bradley D.; Davis, Patricia P.; Upchurch, Billy T.; Puster, Richard L.

1992-01-01

This paper describes the development of a gas collection and analysis system that is to be installed in the Eight-Foot High Temperature Tunnel (8' HTT) at NASA's Langley Research Center. This system will be used to analyze the test gas medium that results after burning a methane-air mixture to achieve the proper tunnel test parameters. The system consists of a sampling rake, a gas sample storage array, and a gas chromatographic system. Gas samples will be analyzed after each run to assure that proper combustion takes place in the tunnel resulting in a correctly balanced composition of the test gas medium. The proper ratio of gas species is critically necessary in order for the proper operation and testing of scramjet engines in the tunnel. After a variety of methane-air burn conditions have been analyzed, additional oxygen will be introduced into the combusted gas and the enriched test gas medium analyzed. The pre/post enrichment sets of data will be compared to verify that the gas species of the test gas medium is correctly balanced for testing of air-breathing engines.

A control system for orbiting tethered-body operations

NASA Technical Reports Server (NTRS)

Eades, J. B., Jr.

1975-01-01

This paper shows that through proper control logic the transfer of men and cargo between spacecrafts, or the 'positioning of packages' adjacent to orbiters, can be accomodated safely and predictably using tethers. Also, these systems may be adapted to rescue and retrieval operations where 'controlled motions' must be maintained. Shown here is a method which illustrates how tethered-body motions are controlled for 'reel-in' and 'reel-out' operations, and for precise 'positioning' purposes. Three control modes are examined; from these are derived sets of universal control parameters capable of predescribing systems of similar types. In addition, these parameters form a basis for designing tethered-body systems and operations.

Navigating the Requirements Jungle

NASA Astrophysics Data System (ADS)

Langer, Boris; Tautschnig, Michael

Research on validation and verification of requirements specifications has thus far focused on functional properties. Yet, in embedded systems, functional requirements constitute only a small fraction of the properties that must hold to guarantee proper and safe operation of the system under design.

Performance test for a solar water heater

NASA Technical Reports Server (NTRS)

1979-01-01

Two reports describe procedures and results of performance tests on domestic solar powered hot water system. Performance tests determine amount of energy collected by system, amount of energy delivered to solar source, power required to operate system and maintain proper tank temperature, overall system efficiency, and temperature distribution in tank.

Rooftop package unit diagnostician

DOEpatents

Chassin, David P [Pasco, WA; Pratt, Robert G [Kennewick, WA; Reid, Larry Dean [Benton City, WA

2004-08-17

A diagnostic system for an HVAC system includes a number of sensors used to measure the operation of the HVAC system. Sensor readings are measured by timing the delay between when a strobe signal is sent to a sensor and when an interrupt signal from the sensor is received. A device driver used to measure the sensor readings stores the sensor readings in pseudo-character device files, which are universally accessible by different subsystems of the diagnostic system. Based on the readings from these sensors, this diagnostic system is able to determine the operational status of the HVAC system and if an economizer in the HVAC system is operating properly.

46 CFR 98.25-35 - Refrigerated systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... temperature of the liquid below atmospheric, at least two complete refrigeration plants automatically... auxiliaries for proper operation. The capacity of each refrigeration compressor shall be sufficient to...

46 CFR 98.25-35 - Refrigerated systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... temperature of the liquid below atmospheric, at least two complete refrigeration plants automatically... auxiliaries for proper operation. The capacity of each refrigeration compressor shall be sufficient to...

46 CFR 98.25-35 - Refrigerated systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... temperature of the liquid below atmospheric, at least two complete refrigeration plants automatically... auxiliaries for proper operation. The capacity of each refrigeration compressor shall be sufficient to...

46 CFR 98.25-35 - Refrigerated systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... temperature of the liquid below atmospheric, at least two complete refrigeration plants automatically... auxiliaries for proper operation. The capacity of each refrigeration compressor shall be sufficient to...

46 CFR 98.25-35 - Refrigerated systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... temperature of the liquid below atmospheric, at least two complete refrigeration plants automatically... auxiliaries for proper operation. The capacity of each refrigeration compressor shall be sufficient to...

49 CFR 193.2619 - Control systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 3 2013-10-01 2013-10-01 false Control systems. 193.2619 Section 193.2619...: FEDERAL SAFETY STANDARDS Maintenance § 193.2619 Control systems. (a) Each control system must be properly adjusted to operate within design limits. (b) If a control system is out of service for 30 days or more, it...

49 CFR 193.2619 - Control systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Control systems. 193.2619 Section 193.2619...: FEDERAL SAFETY STANDARDS Maintenance § 193.2619 Control systems. (a) Each control system must be properly adjusted to operate within design limits. (b) If a control system is out of service for 30 days or more, it...

49 CFR 193.2619 - Control systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Control systems. 193.2619 Section 193.2619...: FEDERAL SAFETY STANDARDS Maintenance § 193.2619 Control systems. (a) Each control system must be properly adjusted to operate within design limits. (b) If a control system is out of service for 30 days or more, it...

49 CFR 193.2619 - Control systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 3 2012-10-01 2012-10-01 false Control systems. 193.2619 Section 193.2619...: FEDERAL SAFETY STANDARDS Maintenance § 193.2619 Control systems. (a) Each control system must be properly adjusted to operate within design limits. (b) If a control system is out of service for 30 days or more, it...

49 CFR 193.2619 - Control systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 3 2014-10-01 2014-10-01 false Control systems. 193.2619 Section 193.2619...: FEDERAL SAFETY STANDARDS Maintenance § 193.2619 Control systems. (a) Each control system must be properly adjusted to operate within design limits. (b) If a control system is out of service for 30 days or more, it...

The Moisture Menace.

ERIC Educational Resources Information Center

Chivetta, Christopher

2001-01-01

Discusses how to control an indoor pool environment by understanding the mechanics of water evaporation, condensation, and migration. Stresses the need for a properly designed, installed, operated, and maintained mechanical system. (GR)

Solid waste management in Abuja, Nigeria.

PubMed

Imam, A; Mohammed, B; Wilson, D C; Cheeseman, C R

2008-01-01

The new city of Abuja provided an opportunity to avoid some of the environmental problems associated with other major cities in Africa. The current status of solid waste management in Abuja has been reviewed and recommendations for improvements are made. The existing solid waste management system is affected by unfavourable economic, institutional, legislative, technical and operational constraints. A reliable waste collection service is needed and waste collection vehicles need to be appropriate to local conditions. More vehicles are required to cope with increasing waste generation. Wastes need to be sorted at source as much as possible, to reduce the amount requiring disposal. Co-operation among communities, the informal sector, the formal waste collectors and the authorities is necessary if recycling rates are to increase. Markets for recycled materials need to be encouraged. Despite recent improvements in the operation of the existing dumpsite, a properly sited engineered landfill should be constructed with operation contracted to the private sector. Wastes dumped along roads, underneath bridges, in culverts and in drainage channels need to be cleared. Small-scale waste composting plants could promote employment, income generation and poverty alleviation. Enforcement of waste management legislation and a proper policy and planning framework for waste management are required. Unauthorized use of land must be controlled by enforcing relevant clauses in development guidelines. Accurate population data is necessary so that waste management systems and infrastructure can be properly planned. Funding and affordability remain major constraints and challenges.

46 CFR 196.15-30 - Emergency lighting and power systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Emergency lighting and power systems. 196.15-30 Section 196.15-30 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH... the system is in proper operating condition. (b) Internal combustion engine driven emergency...

46 CFR 196.15-30 - Emergency lighting and power systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Emergency lighting and power systems. 196.15-30 Section 196.15-30 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH... the system is in proper operating condition. (b) Internal combustion engine driven emergency...

46 CFR 196.15-30 - Emergency lighting and power systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Emergency lighting and power systems. 196.15-30 Section 196.15-30 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH... the system is in proper operating condition. (b) Internal combustion engine driven emergency...

46 CFR 196.15-30 - Emergency lighting and power systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Emergency lighting and power systems. 196.15-30 Section 196.15-30 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH... the system is in proper operating condition. (b) Internal combustion engine driven emergency...

HOW TO SELECT THE PROPER SECURITY AND EQUIPMENT SURVEILLANCE SYSTEMS TO PROTECT YOUR FACILITIES.

ERIC Educational Resources Information Center

Honeywell, Inc., Minneapolis, Minn.

IN PRESENTING A SURVEY OF MODERN SECURITY SYSTEMS, THIS BOOKLET DISCUSSES THE REQUIREMENTS FOR SURVEILLANCE AND PROTECTION OF AREAS, PERIMETER, AND OBJECTS. A VARIETY OF EQUIPMENT IS DESCRIBED WITH DISCUSSION OF OPERATING PROCEDURES, COSTS, AND RECENT DEVELOPMENTS IN SECURITY SYSTEMS. (JT)

An operations concept methodology to achieve low-cost mission operations

NASA Technical Reports Server (NTRS)

Ledbetter, Kenneth W.; Wall, Stephen D.

1993-01-01

Historically, the Mission Operations System (MOS) for a space mission has been designed last because it is needed last. This has usually meant that the ground system must adjust to the flight vehicle design, sometimes at a significant cost. As newer missions have increasingly longer flight operations lifetimes, the MOS becomes proportionally more difficult and more resource-consuming. We can no longer afford to design the MOS last. The MOS concept may well drive the spacecraft, instrument, and mission designs, as well as the ground system. A method to help avoid these difficulties, responding to the changing nature of mission operations is presented. Proper development and use of an Operations Concept document results in a combined flight and ground system design yielding enhanced operability and producing increased flexibility for less cost.

30 CFR 250.430 - When must I install a diverter system?

Code of Federal Regulations, 2014 CFR

2014-07-01

... INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling... diverter system before you drill a conductor or surface hole. The diverter system consists of a diverter... the diverter system to ensure proper diversion of gases, water, drilling fluid, and other materials...

30 CFR 250.430 - When must I install a diverter system?

Code of Federal Regulations, 2012 CFR

2012-07-01

... INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling... diverter system before you drill a conductor or surface hole. The diverter system consists of a diverter... the diverter system to ensure proper diversion of gases, water, drilling fluid, and other materials...

30 CFR 250.430 - When must I install a diverter system?

Code of Federal Regulations, 2013 CFR

2013-07-01

... INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling... diverter system before you drill a conductor or surface hole. The diverter system consists of a diverter... the diverter system to ensure proper diversion of gases, water, drilling fluid, and other materials...

49 CFR 236.505 - Proper operative relation between parts along roadway and parts on locomotive.

Code of Federal Regulations, 2012 CFR

2012-10-01

... INSTRUCTIONS GOVERNING THE INSTALLATION, INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Standards... all conditions of speed, weather, wear, oscillation, and shock. ...

49 CFR 236.505 - Proper operative relation between parts along roadway and parts on locomotive.

Code of Federal Regulations, 2011 CFR

2011-10-01

... INSTRUCTIONS GOVERNING THE INSTALLATION, INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Standards... all conditions of speed, weather, wear, oscillation, and shock. ...

49 CFR 236.505 - Proper operative relation between parts along roadway and parts on locomotive.

Code of Federal Regulations, 2014 CFR

2014-10-01

... INSTRUCTIONS GOVERNING THE INSTALLATION, INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Standards... all conditions of speed, weather, wear, oscillation, and shock. ...

49 CFR 236.505 - Proper operative relation between parts along roadway and parts on locomotive.

Code of Federal Regulations, 2010 CFR

2010-10-01

... INSTRUCTIONS GOVERNING THE INSTALLATION, INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Standards... all conditions of speed, weather, wear, oscillation, and shock. ...

49 CFR 236.505 - Proper operative relation between parts along roadway and parts on locomotive.

Code of Federal Regulations, 2013 CFR

2013-10-01

... INSTRUCTIONS GOVERNING THE INSTALLATION, INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Standards... all conditions of speed, weather, wear, oscillation, and shock. ...

Audit Oversight: Quality Control System at U.S. Special Operations Command Inspector General Audit Division

DTIC Science & Technology

2002-08-21

The Audit Division provides the Commander, U.S. Special Operations Command (USSOCOM) with professional auditing services to safeguard, account for...and ensure the proper use of special operations forces assets in accomplishing the USSOCOM mission. The Audit Division reports to the USSOCOM Inspector...U.S. Army Special Operations Command, Naval Special Warfare Command, and the Joint Special Operations Command. Appendix A contains a summary of the Audit Division policy and procedures.

40 CFR 112.6 - Qualified Facilities Plan Requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Self-Certification of the Plan. If you are an owner or operator of a facility that meets the Tier I... unloading equipment, tank overflow, rupture, or leakage, or any other equipment known to be a source of... the system or procedure in the SPCC Plan and regularly test to ensure proper operation or efficacy. (b...

40 CFR 112.6 - Qualified Facilities Plan Requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Self-Certification of the Plan. If you are an owner or operator of a facility that meets the Tier I... unloading equipment, tank overflow, rupture, or leakage, or any other equipment known to be a source of... the system or procedure in the SPCC Plan and regularly test to ensure proper operation or efficacy. (b...

40 CFR 112.6 - Qualified Facilities Plan Requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Self-Certification of the Plan. If you are an owner or operator of a facility that meets the Tier I... unloading equipment, tank overflow, rupture, or leakage, or any other equipment known to be a source of... the system or procedure in the SPCC Plan and regularly test to ensure proper operation or efficacy. (b...

40 CFR 112.6 - Qualified Facilities Plan Requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Self-Certification of the Plan. If you are an owner or operator of a facility that meets the Tier I... unloading equipment, tank overflow, rupture, or leakage, or any other equipment known to be a source of... the system or procedure in the SPCC Plan and regularly test to ensure proper operation or efficacy. (b...

40 CFR 112.6 - Qualified Facilities Plan Requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Self-Certification of the Plan. If you are an owner or operator of a facility that meets the Tier I... unloading equipment, tank overflow, rupture, or leakage, or any other equipment known to be a source of... the system or procedure in the SPCC Plan and regularly test to ensure proper operation or efficacy. (b...

29 CFR 1926.952 - Mechanical equipment.

Code of Federal Regulations, 2012 CFR

2012-07-01

... of each shift during which the equipment is to be used to determine that the brakes and operating systems are in proper working condition. (3) No employer shall use any motor vehicle equipment having an... shall not be operated closer to any energized line or equipment than the clearances set forth in § 1926...

76 FR 45617 - Notice of Lodging of the Consent Decree Under the Clean Water Act

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-29

...) violations stemming from its failure to properly operate and maintain its Combined Sewer Collection System..., implement approved operation and maintenance schedules of its sewers, conduct a pump station evaluation, as... from the Consent Decree Library, P.O. Box 7611, U.S. Department of Justice, Washington, DC 20044-7611...

14 CFR 23.991 - Fuel pumps.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components... installations, each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel pumps. 23.991 Section 23.991...

14 CFR 23.991 - Fuel pumps.

Code of Federal Regulations, 2014 CFR

2014-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components... installations, each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel pumps. 23.991 Section 23.991...

14 CFR 23.991 - Fuel pumps.

Code of Federal Regulations, 2012 CFR

2012-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components... installations, each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Fuel pumps. 23.991 Section 23.991...

14 CFR 23.991 - Fuel pumps.

Code of Federal Regulations, 2013 CFR

2013-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components... installations, each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Fuel pumps. 23.991 Section 23.991...

14 CFR 23.991 - Fuel pumps.

Code of Federal Regulations, 2011 CFR

2011-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System Components... installations, each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel pumps. 23.991 Section 23.991...

IEEE transactions on vehicular technology, Vol. Vt-19, No. 1

DOT National Transportation Integrated Search

1970-02-01

This special issue deals not only with integrated electronic systems but with the technology that is required to achieve successful operation. To place some of the 1969 dimensions of the highway system in the United States in proper focus, we note th...

Operating a wide-area remote observing system for the W. M. Keck Observatory

NASA Astrophysics Data System (ADS)

Wirth, Gregory D.; Kibrick, Robert I.; Goodrich, Robert W.; Lyke, James E.

2008-07-01

For over a decade, the W. M. Keck Observatory's two 10-meter telescopes have been operated remotely from its Waimea headquarters. Over the last 6 years, WMKO remote observing has expanded to allow teams at dedicated sites in California to observe either in collaboration with colleagues in Waimea or entirely from the U.S. mainland. Once an experimental effort, the Observatory's mainland observing capability is now fully operational, supported on all science instruments (except the interferometer) and regularly used by astronomers at eight mainland sites. Establishing a convenient and secure observing capability from those sites required careful planning to ensure that they are properly equipped and configured. It also entailed a significant investment in hardware and software, including both custom scripts to simplify launching the instrument interface at remote sites and automated routers employing ISDN backup lines to ensure continuation of observing during Internet outages. Observers often wait until shortly before their runs to request use of the mainland facilities. Scheduling these requests and ensuring proper system operation prior to observing requires close coordination between personnel at WMKO and the mainland sites. An established protocol for approving requests and carrying out pre-run checkout has proven useful in ensuring success. The Observatory anticipates enhancing and expanding its remote observing system. Future plans include deploying dedicated summit computers for running VNC server software, implementing a web-based tracking system for mainland-based observing requests, expanding the system to additional mainland sites, and converting to full-time VNC operation for all instruments.

A modular approach for assessing the effect of radiation environments on man in operational systems. The radiobiological vulnerability of man during task performance

NASA Technical Reports Server (NTRS)

Ewing, D. E.

1972-01-01

A modular approach for assessing the affects of radiation environments on man in operational systems has been developed. The feasibility of the model has been proved and the practicality has been assessed. It has been applied to one operational system to date and information obtained has been submitted to systems analysts and mission planners for the assessment of man's vulnerability and impact on systems survivability. In addition, the model has been developed so that the radiobiological data can be input to a sophisticated man-machine interface model to properly relate the radiobiological stress with other mission stresses including the effects of a degraded system.

Pleiades and OCO-2: Using Supercomputing Resources to Process OCO-2 Science Data

NASA Technical Reports Server (NTRS)

LaHaye, Nick

2012-01-01

For a period of ten weeks I got the opportunity to assist in doing research for the OCO-2 project in the Science Data Operations System Team. This research involved writing a prototype interface that would work as a model for the system implemented for the project's operations. This would only be the case if when the system is tested it worked properly and up to the team's standards. This paper gives the details of the research done and its results.

Control of stochastic sensitivity in a stabilization problem for gas discharge system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bashkirtseva, Irina

2015-11-30

We consider a nonlinear dynamic stochastic system with control. A problem of stochastic sensitivity synthesis of the equilibrium is studied. A mathematical technique of the solution of this problem is discussed. This technique is applied to the problem of the stabilization of the operating mode for the stochastic gas discharge system. We construct a feedback regulator that reduces the stochastic sensitivity of the equilibrium, suppresses large-amplitude oscillations, and provides a proper operation of this engineering device.

Operation Results of the Kstar Helium Refrigeration System

NASA Astrophysics Data System (ADS)

Chang, H.-S.; Fauve, E.; Park, D.-S.; Joo, J.-J.; Moon, K.-M.; Cho, K.-W.; Na, H. K.; Kwon, M.; Yang, S.-H.; Gistau-Baguer, G.

2010-04-01

The "first plasma" (100 kA of controllable plasma current for 100 ms) of KSTAR has been successfully generated in July 2008. The major outstanding feature of KSTAR compared to most other Tokamaks is that all the magnet coils are superconducting (SC), which enables higher plasma current values for a longer time duration when the nominal operation status has been reached. However, to establish the operating condition for the SC coils, other cold components, such as thermal shields, coil-supporting structures, SC buslines, and current leads also must be maintained at proper cryogenic temperature levels. A helium refrigeration system (HRS) with an exergetic equivalent cooling power of 9 kW at 4.5 K has been installed for such purposes and successfully commissioned. In this proceeding, we will report on the operation results of the HRS during the first plasma campaign of KSTAR. Using the HRS, the 300-ton cold mass of KSTAR was cooled down from ambient to the operating temperature levels of each cold component. Stable and steady cryogenic conditions, proper for the generation of the "first plasma" have been maintained for three months, after which, all of the cold mass was warmed up again to ambient temperature.

Enhanced operator interface for hand-held landmine detector

NASA Astrophysics Data System (ADS)

Herman, Herman; McMahill, Jeffrey D.; Kantor, George

2001-10-01

As landmines get harder to detect, the complexity of landmine detectors has also been increasing. To increase the probability of detection and decrease the false alarm rate of low metallic landmines, many detectors employ multiple sensing modalities, which include radar and metal detector. Unfortunately, the operator interface for these new detectors stays pretty much the same as for the older detectors. Although the amount of information that the new detectors acquire has increased significantly, the interface has been limited to a simple audio interface. We are currently developing a hybrid audiovisual interface for enhancing the overall performance of the detector. The hybrid audiovisual interface combines the simplicity of the audio output with the rich spatial content of the video display. It is designed to optimally present the output of the detector and also to give the proper feedback to the operator. Instead of presenting all the data to the operator simultaneously, the interface allows the operator to access the information as needed. This capability is critical to avoid information overload, which can significantly reduce the performance of the operator. The audio is used as the primary notification signal, while the video is used for further feedback, discrimination, localization and sensor fusion. The idea is to let the operator gets the feedback that he needs and enable him to look at the data in the most efficient way. We are also looking at a hybrid man-machine detection system which utilizes precise sweeping by the machine and powerful human cognitive ability. In such a hybrid system, the operator is free to concentrate on discriminant task, such as manually fusing the output of the different sensing modalities, instead of worrying about the proper sweep technique. In developing this concept, we have been using the virtual mien lane to validate some of these concepts. We obtained some very encouraging results form our preliminary test. It clearly shows that with the proper feedback, the performance of the operator can be improved significantly in a very short time.

77 FR 20051 - Meeting of the Compact Council for the National Crime Prevention and Privacy Compact

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-03

... provides a legal framework for the establishment of a cooperative federal-state system to exchange such... on the Council. The Council will prescribe system rules and procedures for the effective and proper operation of the Interstate Identification Index system for noncriminal justice purposes. Matters for...

76 FR 20044 - Meeting of the Compact Council for the National Crime Prevention and Privacy Compact

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-11

... provides a legal framework for the establishment of a cooperative Federal-State system to exchange such... on the Council. The Council will prescribe system rules and procedures for the effective and proper operation of the Interstate Identification Index system for noncriminal justice purposes. Matters for...

78 FR 61384 - Meeting of the Compact Council for the National Crime Prevention and Privacy Compact

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-03

... provides a legal framework for the establishment of a cooperative federal-state system to exchange such... on the Council. The Council will prescribe system rules and procedures for the effective and proper operation of the Interstate Identification Index system for noncriminal justice purposes. Matters for...

77 FR 60475 - Meeting of the Compact Council for the National Crime Prevention and Privacy Compact

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-03

... provides a legal framework for the establishment of a cooperative federal-state system to exchange such... on the Council. The Council will prescribe system rules and procedures for the effective and proper operation of the Interstate Identification Index system for noncriminal justice purposes. Matters for...

75 FR 17161 - Meeting of the Compact Council for the National Crime Prevention and Privacy Compact

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-05

... Compact also provides a legal framework for the establishment of a cooperative federal-state system to... agencies to serve on the Council. The Council will prescribe system rules and procedures for the effective and proper operation of the Interstate Identification Index system. Matters for discussion are...

Verification and Implementation of Operations Safety Controls for Flight Missions

NASA Technical Reports Server (NTRS)

Smalls, James R.; Jones, Cheryl L.; Carrier, Alicia S.

2010-01-01

There are several engineering disciplines, such as reliability, supportability, quality assurance, human factors, risk management, safety, etc. Safety is an extremely important engineering specialty within NASA, and the consequence involving a loss of crew is considered a catastrophic event. Safety is not difficult to achieve when properly integrated at the beginning of each space systems project/start of mission planning. The key is to ensure proper handling of safety verification throughout each flight/mission phase. Today, Safety and Mission Assurance (S&MA) operations engineers continue to conduct these flight product reviews across all open flight products. As such, these reviews help ensure that each mission is accomplished with safety requirements along with controls heavily embedded in applicable flight products. Most importantly, the S&MA operations engineers are required to look for important design and operations controls so that safety is strictly adhered to as well as reflected in the final flight product.

Report: EPA’s and Louisiana’s Efforts to Assess and Restore Public Drinking Water Systems after Hurricane Katrina

EPA Pesticide Factsheets

Report #2006-P-00014, March 7, 2006. The Louisiana Department of Health and Hospitals and drinking water systems operators provided the public with timely and accurate information about the safety and proper treatment of drinking water.

On-farm irrigatrion system design and operation

USDA-ARS?s Scientific Manuscript database

Most commercial blueberry fields are irrigated by overhead sprinklers or drip. Water is typically applied one to two times per week as needed with sprinklers, and every one to three days with drip. Sprinkler systems are relatively simple to install and maintain, and when designed properly, obtain re...

Development of the prototype pneumatic transfer system for ITER neutron activation system.

PubMed

Cheon, M S; Seon, C R; Pak, S; Lee, H G; Bertalot, L

2012-10-01

The neutron activation system (NAS) measures neutron fluence at the first wall and the total neutron flux from the ITER plasma, providing evaluation of the fusion power for all operational phases. The pneumatic transfer system (PTS) is one of the key components of the NAS for the proper operation of the system, playing a role of transferring encapsulated samples between the capsule loading machine, irradiation stations, counting stations, and disposal bin. For the validation and the optimization of the design, a prototype of the PTS was developed and capsule transfer tests were performed with the developed system.

How Does a Modern Field Artillery Cannon Battalion Operate in a Degraded, Denied, and Disrupted Space Operating Environment

DTIC Science & Technology

2017-06-09

reports, a potential solution to communication shortfalls was the use of high frequency (HF) Harris radios that possess complex encryption... communications , positioning, and navigation do not properly function, is known as a Degraded, Denied, Disrupted Space Operating Environment (D3SOE).7...battalion operates in a D3SOE. This was a very relevant question for a force increasingly reliant on frequency modulated (FM) radio communication systems

Skylab

NASA Image and Video Library

1973-01-01

This striking image of Skylab was photographed by Astronaut Jack Lousma (Skylab-3), as the second crew reached the orbiting laboratory over the delta of the mighty Amazon River. Skylab's solar arrays were exposed directly to the Sun's rays. Solar energy was transformed into electrical power for operation of all spacecraft systems. The proper operation of these solar arrays was vital to the mission.

14 CFR 25.991 - Fuel pumps.

Code of Federal Regulations, 2012 CFR

2012-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.991 Fuel pumps. (a) Main pumps. Each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Fuel pumps. 25.991 Section 25.991...

14 CFR 25.991 - Fuel pumps.

Code of Federal Regulations, 2013 CFR

2013-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.991 Fuel pumps. (a) Main pumps. Each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Fuel pumps. 25.991 Section 25.991...

14 CFR 25.991 - Fuel pumps.

Code of Federal Regulations, 2014 CFR

2014-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.991 Fuel pumps. (a) Main pumps. Each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel pumps. 25.991 Section 25.991...

14 CFR 25.991 - Fuel pumps.

Code of Federal Regulations, 2011 CFR

2011-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.991 Fuel pumps. (a) Main pumps. Each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel pumps. 25.991 Section 25.991...

14 CFR 25.991 - Fuel pumps.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.991 Fuel pumps. (a) Main pumps. Each fuel pump required for proper engine operation, or required to meet the fuel system... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel pumps. 25.991 Section 25.991...

Operating Procedures to Improve Efficiencies of In vitro Exposure Systems at the Air-Liquid Interface

EPA Science Inventory

The expanding use of in vitro exposure systems for toxicity assessments has created regulatory concerns. Many of these same concerns surround the proper conduct of in vivo inhalation toxicology studies that are addressed in guidelines and Good Laboratory Practice (GLPs) regulatio...

Livermore time-sharing system. Part I. Octopus. Chapter 3. Teletypewriters. [Manual for teletypewriter use

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fletcher, J.G.; Richards, M.D.; Du Bois, P.

1977-04-15

Most of the interactive terminals in the Octopus system are teletypewriters. The behavior of each teletypewriter is closely associated with the operation of the PDP-8 concentrator to which it is attached. This report contains all information necessary for proper use of the teletypewriter. (RWR)

30 CFR 57.11059 - Respirable atmosphere for hoist operators underground.

Code of Federal Regulations, 2010 CFR

2010-07-01

... independent ventilation system shall convert, without contamination, to an approved and properly maintained 2... evacuation. Air for the enclosure's ventilation system shall be provided in one of the following ways: (1) Air coursed from the surface through a borehole into the hoist enclosure directly or through a metal...

33 CFR 164.46 - Automatic Identification System (AIS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... (AIS). 164.46 Section 164.46 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND... Identification System (AIS). (a) The following vessels must have a properly installed, operational, type approved AIS as of the date specified: (1) Self-propelled vessels of 65 feet or more in length, other than...

33 CFR 164.46 - Automatic Identification System (AIS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... (AIS). 164.46 Section 164.46 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND... Identification System (AIS). (a) The following vessels must have a properly installed, operational, type approved AIS as of the date specified: (1) Self-propelled vessels of 65 feet or more in length, other than...

33 CFR 164.46 - Automatic Identification System (AIS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... (AIS). 164.46 Section 164.46 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND... Identification System (AIS). (a) The following vessels must have a properly installed, operational, type approved AIS as of the date specified: (1) Self-propelled vessels of 65 feet or more in length, other than...

33 CFR 164.46 - Automatic Identification System (AIS).

Code of Federal Regulations, 2011 CFR

2011-07-01

... (AIS). 164.46 Section 164.46 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND... Identification System (AIS). (a) The following vessels must have a properly installed, operational, type approved AIS as of the date specified: (1) Self-propelled vessels of 65 feet or more in length, other than...

33 CFR 164.46 - Automatic Identification System (AIS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... (AIS). 164.46 Section 164.46 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND... Identification System (AIS). (a) The following vessels must have a properly installed, operational, type approved AIS as of the date specified: (1) Self-propelled vessels of 65 feet or more in length, other than...

29 CFR 1910.164 - Fire detection systems.

Code of Federal Regulations, 2010 CFR

2010-07-01

... fire detectors and fire detection systems are tested and adjusted as often as needed to maintain proper reliability and operating condition except that factory calibrated detectors need not be adjusted after...) The employer shall also assure that fire detectors that need to be cleaned of dirt, dust, or other...

29 CFR 1910.164 - Fire detection systems.

Code of Federal Regulations, 2014 CFR

2014-07-01

... fire detectors and fire detection systems are tested and adjusted as often as needed to maintain proper reliability and operating condition except that factory calibrated detectors need not be adjusted after...) The employer shall also assure that fire detectors that need to be cleaned of dirt, dust, or other...

29 CFR 1910.164 - Fire detection systems.

Code of Federal Regulations, 2012 CFR

2012-07-01

... fire detectors and fire detection systems are tested and adjusted as often as needed to maintain proper reliability and operating condition except that factory calibrated detectors need not be adjusted after...) The employer shall also assure that fire detectors that need to be cleaned of dirt, dust, or other...

29 CFR 1910.164 - Fire detection systems.

Code of Federal Regulations, 2013 CFR

2013-07-01

... fire detectors and fire detection systems are tested and adjusted as often as needed to maintain proper reliability and operating condition except that factory calibrated detectors need not be adjusted after...) The employer shall also assure that fire detectors that need to be cleaned of dirt, dust, or other...

29 CFR 1910.164 - Fire detection systems.

Code of Federal Regulations, 2011 CFR

2011-07-01

... fire detectors and fire detection systems are tested and adjusted as often as needed to maintain proper reliability and operating condition except that factory calibrated detectors need not be adjusted after...) The employer shall also assure that fire detectors that need to be cleaned of dirt, dust, or other...

Software solutions manage the definition, operation, maintenance and configuration control of the National Ignition Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dobson, D; Churby, A; Krieger, E

2011-07-25

The National Ignition Facility (NIF) is the world's largest laser composed of millions of individual parts brought together to form one massive assembly. Maintaining control of the physical definition, status and configuration of this structure is a monumental undertaking yet critical to the validity of the shot experiment data and the safe operation of the facility. The NIF business application suite of software provides the means to effectively manage the definition, build, operation, maintenance and configuration control of all components of the National Ignition Facility. State of the art Computer Aided Design software applications are used to generate a virtualmore » model and assemblies. Engineering bills of material are controlled through the Enterprise Configuration Management System. This data structure is passed to the Enterprise Resource Planning system to create a manufacturing bill of material. Specific parts are serialized then tracked along their entire lifecycle providing visibility to the location and status of optical, target and diagnostic components that are key to assessing pre-shot machine readiness. Nearly forty thousand items requiring preventive, reactive and calibration maintenance are tracked through the System Maintenance & Reliability Tracking application to ensure proper operation. Radiological tracking applications ensure proper stewardship of radiological and hazardous materials and help provide a safe working environment for NIF personnel.« less

Employing lighting techniques during on-orbit operations

NASA Technical Reports Server (NTRS)

Wheelwright, Charles D.; Toole, Jennifer R.

1991-01-01

As a result of past space missions and evaluations, many procedures have been established and shown to be prudent applications for use in present and future space environment scenarios. However, recent procedures to employ the use of robotics to assist crewmembers in performing tasks which require viewing remote and obstructed locations have led to a need to pursue alternative methods to assist in these operations. One of those techniques which is under development entails incorporating the use of suitable lighting aids/techniques with a closed circuit television (CCTV) camera/monitor system to supervise the robotics operations. The capability to provide adequate lighting during grappling, deploying, docking and berthing operations under all on-orbit illumination conditions is essential to a successful mission. Using automated devices such as the Remote Manipulator System (RMS) to dock and berth a vehicle during payload retrieval, under nighttime, earthshine, solar, or artificial illumination conditions can become a cumbersome task without first incorporating lighting techniques that provide the proper target illumination, orientation, and alignment cues. Studies indicate that the use of visual aids such as the CCTV with a pretested and properly oriented lighting system can decrease the time necessary to accomplish grappling tasks. Evaluations have been and continue to be performed to assess the various on-orbit conditions in order to predict and determine the appropriate lighting techniques and viewing angles necessary to assist crewmembers in payload operations.

Employing lighting techniques during on-orbit operations

NASA Astrophysics Data System (ADS)

Wheelwright, Charles D.; Toole, Jennifer R.

As a result of past space missions and evaluations, many procedures have been established and shown to be prudent applications for use in present and future space environment scenarios. However, recent procedures to employ the use of robotics to assist crewmembers in performing tasks which require viewing remote and obstructed locations have led to a need to pursue alternative methods to assist in these operations. One of those techniques which is under development entails incorporating the use of suitable lighting aids/techniques with a closed circuit television (CCTV) camera/monitor system to supervise the robotics operations. The capability to provide adequate lighting during grappling, deploying, docking and berthing operations under all on-orbit illumination conditions is essential to a successful mission. Using automated devices such as the Remote Manipulator System (RMS) to dock and berth a vehicle during payload retrieval, under nighttime, earthshine, solar, or artificial illumination conditions can become a cumbersome task without first incorporating lighting techniques that provide the proper target illumination, orientation, and alignment cues. Studies indicate that the use of visual aids such as the CCTV with a pretested and properly oriented lighting system can decrease the time necessary to accomplish grappling tasks. Evaluations have been and continue to be performed to assess the various on-orbit conditions in order to predict and determine the appropriate lighting techniques and viewing angles necessary to assist crewmembers in payload operations.

Demonstration of an Enhanced Vertical Magnetic Gradient System for UXO

DTIC Science & Technology

2008-12-01

fluxgate magnetometers , data recording console, laser altimeter, and acoustic altimeters were tested to ensure proper operation and performance. The VG...Simultaneous Electromagnetic Induction and Magnetometer System WAA wide area assessment ACKNOWLEDGEMENTS We wish to express our sincere...sensors. The benefits of vertical gradient (VG) configurations in magnetometer systems are common knowledge, and these configurations are routinely

30 CFR 75.312 - Main mine fan examinations and records.

Code of Federal Regulations, 2012 CFR

2012-07-01

... fan and the fan monitoring system are operating properly. No review is required on any day when no one... initials and date in a computer system so as to be secure and not susceptible to alteration. (g)(1... alteration or electronically in a computer system so as to be secure and not susceptible to alteration. (2...

30 CFR 75.312 - Main mine fan examinations and records.

Code of Federal Regulations, 2013 CFR

2013-07-01

... fan and the fan monitoring system are operating properly. No review is required on any day when no one... initials and date in a computer system so as to be secure and not susceptible to alteration. (g)(1... alteration or electronically in a computer system so as to be secure and not susceptible to alteration. (2...

30 CFR 75.312 - Main mine fan examinations and records.

Code of Federal Regulations, 2014 CFR

2014-07-01

... fan and the fan monitoring system are operating properly. No review is required on any day when no one... initials and date in a computer system so as to be secure and not susceptible to alteration. (g)(1... alteration or electronically in a computer system so as to be secure and not susceptible to alteration. (2...

30 CFR 75.312 - Main mine fan examinations and records.

Code of Federal Regulations, 2011 CFR

2011-07-01

... fan and the fan monitoring system are operating properly. No review is required on any day when no one... initials and date in a computer system so as to be secure and not susceptible to alteration. (g)(1... alteration or electronically in a computer system so as to be secure and not susceptible to alteration. (2...

30 CFR 75.312 - Main mine fan examinations and records.

Code of Federal Regulations, 2010 CFR

2010-07-01

... fan and the fan monitoring system are operating properly. No review is required on any day when no one... initials and date in a computer system so as to be secure and not susceptible to alteration. (g)(1... alteration or electronically in a computer system so as to be secure and not susceptible to alteration. (2...

Natural Gas Vehicle Cylinder Safety, Training and Inspection Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hank Seiff

2008-12-31

Under the auspices of the National Energy Technology Laboratory and the US Department of Energy, the Clean Vehicle Education Foundation conducted a three-year program to increase the understanding of the safe and proper use and maintenance of vehicular compressed natural gas (CNG) fuel systems. High-pressure fuel systems require periodic inspection and maintenance to insure safe and proper operation. The project addressed the needs of CNG fuel containers (cylinders) and associated high-pressure fuel system components related to existing law, codes and standards (C&S), available training and inspection programs, and assured coordination among vehicle users, public safety officials, fueling station operators andmore » training providers. The program included a public and industry awareness campaign, establishment and administration of a cylinder inspector certification training scholarship program, evaluation of current safety training and testing practices, monitoring and investigation of CNG vehicle incidents, evaluation of a cylinder recertification program and the migration of CNG vehicle safety knowledge to the nascent hydrogen vehicle community.« less

DoD Is Not Properly Monitoring the Initiation of Maintenance for Facilities at Kandahar Airfield, Afghanistan (REDACTED)

DTIC Science & Technology

2013-09-30

fire sprinkler system during the initial construction of the RSOI facilities. The construction contract to build the RSOI...International Building Code. Compliant manual and automatic fire alarm and notification systems , portable fire extinguishers, fire sprinkler systems ...automatic fire sprinkler system that was not operational, a fire department connection that was obstructed, and a fire detection system

14 CFR 61.87 - Solo requirements for student pilots.

Code of Federal Regulations, 2014 CFR

2014-01-01

... flight preparation procedures, including preflight planning and preparation, powerplant operation, and...) Proper flight preparation procedures, including preflight planning and preparation, powerplant operation...) Proper flight preparation procedures, including preflight planning and preparation, powerplant operation...

14 CFR 61.87 - Solo requirements for student pilots.

Code of Federal Regulations, 2010 CFR

2010-01-01

... flight preparation procedures, including preflight planning and preparation, powerplant operation, and...) Proper flight preparation procedures, including preflight planning and preparation, powerplant operation...) Proper flight preparation procedures, including preflight planning and preparation, powerplant operation...

14 CFR 61.87 - Solo requirements for student pilots.

Code of Federal Regulations, 2013 CFR

2013-01-01

... flight preparation procedures, including preflight planning and preparation, powerplant operation, and...) Proper flight preparation procedures, including preflight planning and preparation, powerplant operation...) Proper flight preparation procedures, including preflight planning and preparation, powerplant operation...

14 CFR 61.87 - Solo requirements for student pilots.

Code of Federal Regulations, 2012 CFR

2012-01-01

... flight preparation procedures, including preflight planning and preparation, powerplant operation, and...) Proper flight preparation procedures, including preflight planning and preparation, powerplant operation...) Proper flight preparation procedures, including preflight planning and preparation, powerplant operation...

14 CFR 61.87 - Solo requirements for student pilots.

Code of Federal Regulations, 2011 CFR

2011-01-01

... flight preparation procedures, including preflight planning and preparation, powerplant operation, and...) Proper flight preparation procedures, including preflight planning and preparation, powerplant operation...) Proper flight preparation procedures, including preflight planning and preparation, powerplant operation...

System Engineering of Photonic Systems for Space Application

NASA Technical Reports Server (NTRS)

Watson, Michael D.; Pryor, Jonathan E.

2014-01-01

The application of photonics in space systems requires tight integration with the spacecraft systems to ensure accurate operation. This requires some detailed and specific system engineering to properly incorporate the photonics into the spacecraft architecture and to guide the spacecraft architecture in supporting the photonics devices. Recent research in product focused, elegant system engineering has led to a system approach which provides a robust approach to this integration. Focusing on the mission application and the integration of the spacecraft system physics incorporation of the photonics can be efficiently and effectively accomplished. This requires a clear understanding of the driving physics properties of the photonics device to ensure proper integration with no unintended consequences. The driving physics considerations in terms of optical performance will be identified for their use in system integration. Keywords: System Engineering, Optical Transfer Function, Optical Physics, Photonics, Image Jitter, Launch Vehicle, System Integration, Organizational Interaction

A Battalion/Division Fiscal Control System for Training Resource Management.

DTIC Science & Technology

1981-12-01

of each command using it. With many Army fiscal procedures consuming large volumes of time and resources to support operations with questionable...Document (FAD)) spe- cifying the appropriation and budget programs for which the funds may be used . The FAD is the installation’s approved financial...operating budgets. Although a proper term would be operating targets, budget is used for ease of understanding. These funds are principally for general

Shredded Waste Downdraft Gasifier for Overseas Contingency Operations Waste-to-Energy Conversion

DTIC Science & Technology

2015-06-01

results of the proposed experimental test plan and the design of a shredded waste WEC system in Task 5. A. Generators (Left) and Shredded...Shredded Waste 4 8.5 – 27.1 5.1.1.4 Wall Friction Tests In addition to a properly sized outlet, the design of a mass flow vessel must consider...consolidating pressures. 5.1.2.3 Wall Friction Tests In addition to a properly sized outlet, the design of a mass flow vessel must consider the

A study of commuter airline economics

NASA Technical Reports Server (NTRS)

Summerfield, J. R.

1976-01-01

Variables are defined and cost relationships developed that describe the direct and indirect operating costs of commuter airlines. The study focused on costs for new aircraft and new aircraft technology when applied to the commuter airline industry. With proper judgement and selection of input variables, the operating costs model was shown to be capable of providing economic insight into other commuter airline system evaluations.

Skylab

NASA Image and Video Library

1974-07-26

In this photograph, a skylab-4 astronaut performs Extra Vehicular Activities (EVA) outside of the lab. The third crew (Skylab-4) spent 84 days in the orbiting laboratory. The solar observatory was designed for full exposure to the Sun throughout most of the Skylab mission. Solar energy was transformed into electrical power for operation of all spacecraft systems. The proper operation of these solar arrays was vital to the mission.

Skylab

NASA Image and Video Library

1974-01-01

This photograph was taken as the third crew (Skylab-4) departed the space station. The solar observatory was designed for full exposure to the Sun throughout most of the Skylab mission. Solar energy was transformed into electrical power for operation of all spacecraft systems. The proper operation of these solar arrays was vital to the mission. This Skylab in orbit view was taken by the Skylab-4 crew.

Transient performance and temperature field of a natural convection air dehumidifier loop

NASA Astrophysics Data System (ADS)

Fazilati, Mohammad Ali; Sedaghat, Ahmad; Alemrajabi, Ali-Akbar

2017-07-01

In this paper, transient performance of the previously introduced natural convection heat and mass transfer loop is investigated for an air dehumidifier system. The performance of the loop is studied in different conditions of heat source/heat sink temperature and different startup desiccant concentrations. Unlike conventional loops, it is observed that natural convection of the fluid originates from the heat sink towards the heat source. The proper operation of the cycle is highly dependent on the heat sink/heat source temperatures. To reduce the time constant of the system, a proper desiccant concentration should be adopted for charge of the loop.

77 FR 55768 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-11

... prompted by a report that during a test of the oxygen system, an operator found that the passenger oxygen masks did not properly flow oxygen, and that a loud noise occurred in the overhead area, which was... airplane oxygen system to ensure clamshell couplers are installed and fully latched, and corrective actions...

78 FR 23110 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-18

... that during a test of the oxygen system, an operator found that the passenger oxygen masks did not properly flow oxygen, and that a loud noise occurred in the overhead area, which was caused by the flex... airplanes, performing a detailed inspection of certain areas of the airplane oxygen system to ensure...

Antiproton acceleration in the Fermilab Main Ring and Tevatron

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martin, P.; Dinkel, J.; Ducar, R.

1987-03-01

The operation of the Fermilab Main Ring and Tevatron rf systems for colliding beams physics is discussed. The changes in the rf feedback system required for the accelration of antiprotons, and the methods for achieving proper transfer of both protons and antiprotons are described. Data on acceleration and transfer efficiencies are presented.

10 CFR 36.41 - Construction monitoring and acceptance testing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... system will operate properly if offsite power is lost and shall verify that the computer has security... system to assure that the requirements in § 36.35 are met for protection of the source rack and the... protection. For panoramic irradiators, the licensee shall test the ability of the heat and smoke detectors to...

10 CFR 36.41 - Construction monitoring and acceptance testing.

Code of Federal Regulations, 2011 CFR

2011-01-01

... system will operate properly if offsite power is lost and shall verify that the computer has security... system to assure that the requirements in § 36.35 are met for protection of the source rack and the... protection. For panoramic irradiators, the licensee shall test the ability of the heat and smoke detectors to...

10 CFR 36.41 - Construction monitoring and acceptance testing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... system will operate properly if offsite power is lost and shall verify that the computer has security... system to assure that the requirements in § 36.35 are met for protection of the source rack and the... protection. For panoramic irradiators, the licensee shall test the ability of the heat and smoke detectors to...

10 CFR 36.41 - Construction monitoring and acceptance testing.

Code of Federal Regulations, 2012 CFR

2012-01-01

... system will operate properly if offsite power is lost and shall verify that the computer has security... system to assure that the requirements in § 36.35 are met for protection of the source rack and the... protection. For panoramic irradiators, the licensee shall test the ability of the heat and smoke detectors to...

10 CFR 36.41 - Construction monitoring and acceptance testing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... system will operate properly if offsite power is lost and shall verify that the computer has security... system to assure that the requirements in § 36.35 are met for protection of the source rack and the... protection. For panoramic irradiators, the licensee shall test the ability of the heat and smoke detectors to...

Embedded Multiprocessor Technology for VHSIC Insertion

NASA Technical Reports Server (NTRS)

Hayes, Paul J.

1990-01-01

Viewgraphs on embedded multiprocessor technology for VHSIC insertion are presented. The objective was to develop multiprocessor system technology providing user-selectable fault tolerance, increased throughput, and ease of application representation for concurrent operation. The approach was to develop graph management mapping theory for proper performance, model multiprocessor performance, and demonstrate performance in selected hardware systems.

Smaller Satellite Operations Near Geostationary Orbit

DTIC Science & Technology

2007-09-01

At the time, this was considered a very difficult task, due to the complexity involved with creating computer code to autonomously perform... computer systems and even permanently damage equipment. Depending on the solar cycle, solar weather will be properly characterized and modeled to...30 Wayne Tomasi. Electronic Communciations Systems. Upper Saddle River: Pearson Education, 2004. 1041

Reliability of Navigation Service Provided by the Global Positioning System

DOT National Transportation Integrated Search

1985-09-01

The planned NAVSTAR/GPS satellite constellation of 18 satellites plus 3 active will provide excellent coverage over the continental United States (CONUS) if all are operating properly. This report examines the coverage under conditions of one satelli...

Impact of quasar proper motions on the alignment between the International Celestial Reference Frame and the Gaia reference frame

NASA Astrophysics Data System (ADS)

Liu, J.-C.; Malkin, Z.; Zhu, Z.

2018-03-01

The International Celestial Reference Frame (ICRF) is currently realized by the very long baseline interferometry (VLBI) observations of extragalactic sources with the zero proper motion assumption, while Gaia will observe proper motions of these distant and faint objects to an accuracy of tens of microarcseconds per year. This paper investigates the difference between VLBI and Gaia quasar proper motions and it aims to understand the impact of quasar proper motions on the alignment of the ICRF and Gaia reference frame. We use the latest time series data of source coordinates from the International VLBI Service analysis centres operated at Goddard Space Flight Center (GSF2017) and Paris observatory (OPA2017), as well as the Gaia auxiliary quasar solution containing 2191 high-probability optical counterparts of the ICRF2 sources. The linear proper motions in right ascension and declination of VLBI sources are derived by least-squares fits while the proper motions for Gaia sources are simulated taking into account the acceleration of the Solar system barycentre and realistic uncertainties depending on the source brightness. The individual and global features of source proper motions in GSF2017 and OPA2017 VLBI data are found to be inconsistent, which may result from differences in VLBI observations, data reduction and analysis. A comparison of the VLBI and Gaia proper motions shows that the accuracies of the components of rotation and glide between the two systems are 2-4 μas yr- 1 based on about 600 common sources. For the future alignment of the ICRF and Gaia reference frames at different wavelengths, the proper motions of quasars must necessarily be considered.

Hybrid associative memory using an incoherent correlation system

NASA Astrophysics Data System (ADS)

Taniguchi, Masaki; Ichioka, Yoshiki; Matsuoka, Katsunori

1990-10-01

A hybrid heteroassociative memory is presented that uses an incoherent system in which two correlators and a nonlinear element form a nonlinear feedback system. This system can recall any pattern from an input pattern without cross-talk or ghosts by properly designing a pair of filters installed in the correlators. Experiments on a simple hybrid system were performed to ensure the operation of the system and to demonstrate the usefulness of this proposed system.

Modelling operations and security of cloud systems using Z-notation and Chinese Wall security policy

NASA Astrophysics Data System (ADS)

Basu, Srijita; Sengupta, Anirban; Mazumdar, Chandan

2016-11-01

Enterprises are increasingly using cloud computing for hosting their applications. Availability of fast Internet and cheap bandwidth are causing greater number of people to use cloud-based services. This has the advantage of lower cost and minimum maintenance. However, ensuring security of user data and proper management of cloud infrastructure remain major areas of concern. Existing techniques are either too complex, or fail to properly represent the actual cloud scenario. This article presents a formal cloud model using the constructs of Z-notation. Principles of the Chinese Wall security policy have been applied to design secure cloud-specific operations. The proposed methodology will enable users to safely host their services, as well as process sensitive data, on cloud.

The von Neumann model of measurement in quantum mechanics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mello, Pier A.

2014-01-08

We describe how to obtain information on a quantum-mechanical system by coupling it to a probe and detecting some property of the latter, using a model introduced by von Neumann, which describes the interaction of the system proper with the probe in a dynamical way. We first discuss single measurements, where the system proper is coupled to one probe with arbitrary coupling strength. The goal is to obtain information on the system detecting the probe position. We find the reduced density operator of the system, and show how Lüders rule emerges as the limiting case of strong coupling. The vonmore » Neumann model is then generalized to two probes that interact successively with the system proper. Now we find information on the system by detecting the position-position and momentum-position correlations of the two probes. The so-called 'Wigner's formula' emerges in the strong-coupling limit, while 'Kirkwood's quasi-probability distribution' is found as the weak-coupling limit of the above formalism. We show that successive measurements can be used to develop a state-reconstruction scheme. Finally, we find a generalized transform of the state and the observables based on the notion of successive measurements.« less

Analysis of space tug operating techniques (study 2.4). Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1972-01-01

The costs of tug refurbishment were studied, using existing cost estimating relationships, to establish the cost of maintaining the reusable third stage of the space transportation system. Refurbishment operations sheets which describe the actual tasks that are necessary to keep the equipment functioning properly were used along with refurbishment operations sheets which contain all of the pertinent descriptive information for each of the major vehicle areas. Tug refurbishment costs per mission are tabulated.

Water Recovery System Architecture and Operational Concepts to Accommodate Dormancy

NASA Technical Reports Server (NTRS)

Carter, Layne; Tabb, David; Anderson, Molly

2017-01-01

Future manned missions beyond low Earth orbit will include intermittent periods of extended dormancy. The mission requirement includes the capability for life support systems to support crew activity, followed by a dormant period of up to one year, and subsequently for the life support systems to come back online for additional crewed missions. NASA personnel are evaluating the architecture and operational concepts that will allow the Water Recovery System (WRS) to support such a mission. Dormancy could be a critical issue due to concerns with microbial growth or chemical degradation that might prevent water systems from operating properly when the crewed mission began. As such, it is critical that the water systems be designed to accommodate this dormant period. This paper identifies dormancy issues, concepts for updating the WRS architecture and operational concepts that will enable the WRS to support the dormancy requirement.

Development of the Macro Command Editing Executive System for Factory Workers-Oriented Programless Visual Inspection System

NASA Astrophysics Data System (ADS)

Anezaki, Takashi; Wakitani, Kouichi; Nakamura, Masatoshi; Kubo, Hiroyasu

Because visual inspection systems are difficult to tune, they create many problems for the kaizen process. This results in increased development costs and time to assure that the inspection systems function properly. In order to improve inspection system development, we designed an easy-tuning system called a “Program-less” visual inspection system. The ROI macro command which consisted of eight kinds of shape recognition macro commands and decision, operation, control commands was built. Furthermore, the macro command editing executive system was developed by the operation of only the GUI without editing source program. The validity of the ROI macro command was proved by the application of 488 places.

14 CFR 23.671 - General.

Code of Federal Regulations, 2013 CFR

2013-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Design and Construction Control Systems § 23.671 General. (a) Each control must operate easily, smoothly, and positively enough to allow proper performance of its functions. (b) Controls must be arranged and identified to provide for...

14 CFR 23.671 - General.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Design and Construction Control Systems § 23.671 General. (a) Each control must operate easily, smoothly, and positively enough to allow proper performance of its functions. (b) Controls must be arranged and identified to provide for...

14 CFR 23.671 - General.

Code of Federal Regulations, 2012 CFR

2012-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Design and Construction Control Systems § 23.671 General. (a) Each control must operate easily, smoothly, and positively enough to allow proper performance of its functions. (b) Controls must be arranged and identified to provide for...

14 CFR 23.671 - General.

Code of Federal Regulations, 2014 CFR

2014-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Design and Construction Control Systems § 23.671 General. (a) Each control must operate easily, smoothly, and positively enough to allow proper performance of its functions. (b) Controls must be arranged and identified to provide for...

14 CFR 23.671 - General.

Code of Federal Regulations, 2011 CFR

2011-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Design and Construction Control Systems § 23.671 General. (a) Each control must operate easily, smoothly, and positively enough to allow proper performance of its functions. (b) Controls must be arranged and identified to provide for...

46 CFR 61.35-1 - General.

Code of Federal Regulations, 2010 CFR

2010-10-01

... equipment must be tested and inspected to verify their proper design, construction, installation, and operation. (d) All tests must be performed after installation of the automatic auxiliary boiler and its... monitored system conditions by misadjustment, artificial signals, improper wiring, tampering, or revision of...

Social Institutions and Nuclear Energy

ERIC Educational Resources Information Center

Weinberg, Alvin M.

1972-01-01

Nuclear technologists can offer an all but infinite source of relatively cheap and clean energy" but society must decide whether the price of eternal vigilance needed to ensure proper and safe operation of its nuclear energy system" is worth the benefits. (Author/AL)

On Board Data Acquisition System with Intelligent Transducers for Unmanned Aerial Vehicles

NASA Astrophysics Data System (ADS)

Rochala, Zdzisław

2012-02-01

This report presents conclusions from research project no. ON50900363 conducted at the Mechatronics Department, Military University of Technology in the years 2007-2010. As the main object of the study involved the preparation of a concept and the implementation of an avionics data acquisition system intended for research during flight of unmanned aerial vehicles of the mini class, this article presents a design of an avionics system and describes equipment solutions of a distributed measurement system intended for data acquisition consisting of intelligent transducers. The data collected during a flight controlled by an operator confirmed proper operation of the individual components of the data acquisition system.

Advanced Design Features of APR1400 and Realization in Shin Kori Construction Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

OH, S.J.; Park, K.C.; Kim, H.G.

2006-07-01

APR1400 adopted several advanced design features. To ensure their proper operation as a part of ShinKori 3,4 project, both experimental and analytical work are continuing. In this paper, work on the advanced design features related to enhanced safety is examined. APR1400 safety injection system consists of four independent trains which include four safety injection pump and tanks. A passive flow regulating device called fluidic device is installed in the safety injection tanks. Separate effect tests including a full scale fluidic device tests have been conducted. Integral system tests are in progress. Combination of these work with the analytical work usingmore » RELAP5/Mod3 would ensure the proper operation of the new safety injection systems. To mitigate severe accidents, hydrogen mitigation system using PARs and igniters is adopted. Also, active injection system and the streamlined insulation design are adopted to enhance the in-vessel retention capability with the external cooling of RPV strategy. Analytic work with supporting experiments is performed. We are certain that these preparatory work would help the successful adaptation of ADF in ShinKori project. (authors)« less

30 CFR 250.802 - Design, installation, and operation of surface production-safety systems.

Code of Federal Regulations, 2010 CFR

2010-07-01

... properly or if any fluid flow is observed during the leakage test, the valve shall be repaired or replaced... maintenance of all fire- and gas-detection systems shall include the following: (i) Type, location, and number of detection sensors; (ii) Type and kind of alarms, including emergency equipment to be activated...

46 CFR 58.30-20 - Fluid power hose and fittings.

Code of Federal Regulations, 2012 CFR

2012-10-01

... MACHINERY AND RELATED SYSTEMS Fluid Power and Control Systems § 58.30-20 Fluid power hose and fittings. (a... 46 Shipping 2 2012-10-01 2012-10-01 false Fluid power hose and fittings. 58.30-20 Section 58.30-20... of flexible hose where required for proper operation of machinery and components in the hydraulic...

46 CFR 58.30-20 - Fluid power hose and fittings.

Code of Federal Regulations, 2011 CFR

2011-10-01

... MACHINERY AND RELATED SYSTEMS Fluid Power and Control Systems § 58.30-20 Fluid power hose and fittings. (a... 46 Shipping 2 2011-10-01 2011-10-01 false Fluid power hose and fittings. 58.30-20 Section 58.30-20... of flexible hose where required for proper operation of machinery and components in the hydraulic...

46 CFR 58.30-20 - Fluid power hose and fittings.

Code of Federal Regulations, 2013 CFR

2013-10-01

... MACHINERY AND RELATED SYSTEMS Fluid Power and Control Systems § 58.30-20 Fluid power hose and fittings. (a... 46 Shipping 2 2013-10-01 2013-10-01 false Fluid power hose and fittings. 58.30-20 Section 58.30-20... of flexible hose where required for proper operation of machinery and components in the hydraulic...

Director, Operational Test and Evaluation

DTIC Science & Technology

2007-12-01

important, and all – collectively – are necessary to properly set requirements, incentivize industry, oversee system design and development, and finally...evaluation planning which defines testing required for all system-level evaluation. • Enable access to all system-level test data by government DT...responsible for sustainment cost estimates, and with the OTAs, to contribute relevant data. As with all new missions, there is a question of resources

Green operators for low regularity spacetimes

NASA Astrophysics Data System (ADS)

Sanchez Sanchez, Yafet; Vickers, James

2018-02-01

In this paper we define and construct advanced and retarded Green operators for the wave operator on spacetimes with low regularity. In order to do so we require that the spacetime satisfies the condition of generalised hyperbolicity which is equivalent to well-posedness of the classical inhomogeneous problem with zero initial data where weak solutions are properly supported. Moreover, we provide an explicit formula for the kernel of the Green operators in terms of an arbitrary eigenbasis of H 1 and a suitable Green matrix that solves a system of second order ODEs.

Analysis of transit contracting models and proper incentives for long-term success : [summary].

DOT National Transportation Integrated Search

2013-11-01

In many locales, transit budgets are beng tightened, and transit systems are being challenged to operate more costeffectively. At the same time, demand for services is increasing. This has renewed interest in contracting fixed route service. Howev...

Updating the USDA ARS rotary wing nozzle models

USDA-ARS?s Scientific Manuscript database

Optimizing aerial spray applications requires proper setup of the sprayer system, particularly with respect to nozzle selection and operation, which significantly affects spray deposition, product efficacy, and spray drift. Droplet size from an aerial application is a function of the combination of...

Autonomous System Technologies for Resilient Airspace Operations

NASA Technical Reports Server (NTRS)

Houston, Vincent E.; Le Vie, Lisa R.

2017-01-01

Increasing autonomous systems within the aircraft cockpit begins with an effort to understand what autonomy is and developing the technology that encompasses it. Autonomy allows an agent, human or machine, to act independently within a circumscribed set of goals; delegating responsibility to the agent(s) to achieve overall system objective(s). Increasingly Autonomous Systems (IAS) are the highly sophisticated progression of current automated systems toward full autonomy. Working in concert with humans, these types of technologies are expected to improve the safety, reliability, costs, and operational efficiency of aviation. IAS implementation is imminent, which makes the development and the proper performance of such technologies, with respect to cockpit operation efficiency, the management of air traffic and data communication information, vital. A prototype IAS agent that attempts to optimize the identification and distribution of "relevant" air traffic data to be utilized by human crews during complex airspace operations has been developed.

Development of an image operation system with a motion sensor in dental radiology.

PubMed

Sato, Mitsuru; Ogura, Toshihiro; Yasumoto, Yoshiaki; Kadowaki, Yuta; Hayashi, Norio; Doi, Kunio

2015-07-01

During examinations and/or treatment, a dentist in the examination room needs to view images with a proper display system. However, they cannot operate the image display system by hands, because dentists always wear gloves to be kept their hands away from unsanitized materials. Therefore, we developed a new image operating system that uses a motion sensor. We used the Leap motion sensor technique to read the hand movements of a dentist. We programmed the system using C++ to enable various movements of the display system, i.e., click, double click, drag, and drop. Thus, dentists with their gloves on in the examination room can control dental and panoramic images on the image display system intuitively and quickly with movement of their hands only. We investigated the time required with the conventional method using a mouse and with the new method using the finger operation. The average operation time with the finger method was significantly shorter than that with the mouse method. This motion sensor method, with appropriate training for finger movements, can provide a better operating performance than the conventional mouse method.

Planning low-carbon electricity systems under uncertainty considering operational flexibility and smart grid technologies.

PubMed

Moreno, Rodrigo; Street, Alexandre; Arroyo, José M; Mancarella, Pierluigi

2017-08-13

Electricity grid operators and planners need to deal with both the rapidly increasing integration of renewables and an unprecedented level of uncertainty that originates from unknown generation outputs, changing commercial and regulatory frameworks aimed to foster low-carbon technologies, the evolving availability of market information on feasibility and costs of various technologies, etc. In this context, there is a significant risk of locking-in to inefficient investment planning solutions determined by current deterministic engineering practices that neither capture uncertainty nor represent the actual operation of the planned infrastructure under high penetration of renewables. We therefore present an alternative optimization framework to plan electricity grids that deals with uncertain scenarios and represents increased operational details. The presented framework is able to model the effects of an array of flexible, smart grid technologies that can efficiently displace the need for conventional solutions. We then argue, and demonstrate via the proposed framework and an illustrative example, that proper modelling of uncertainty and operational constraints in planning is key to valuing operationally flexible solutions leading to optimal investment in a smart grid context. Finally, we review the most used practices in power system planning under uncertainty, highlight the challenges of incorporating operational aspects and advocate the need for new and computationally effective optimization tools to properly value the benefits of flexible, smart grid solutions in planning. Such tools are essential to accelerate the development of a low-carbon energy system and investment in the most appropriate portfolio of renewable energy sources and complementary enabling smart technologies.This article is part of the themed issue 'Energy management: flexibility, risk and optimization'. © 2017 The Author(s).

Fiber Optic Cable Thermal Preparation to Ensure Stable Operation

NASA Technical Reports Server (NTRS)

Thoames Jr, William J.; Chuska, Rick F.; LaRocca, Frank V.; Switzer, Robert C.; Macmurphy, Shawn L.; Ott, Melanie N.

2008-01-01

Fiber optic cables are widely used in modern systems that must provide stable operation during exposure to changing environmental conditions. For example, a fiber optic cable on a satellite may have to reliably function over a temperature range of -50 C up to 125 C. While the system requirements for a particular application will dictate the exact method by which the fibers should be prepared, this work will examine multiple ruggedized fibers prepared in different fashions and subjected to thermal qualification testing. The data show that if properly conditioned the fiber cables can provide stable operation, but if done incorrectly, they will have large fluctuations in transmission.

40 CFR 57.503 - Control measures.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., installation and proper operation of primary hoods on all active matte tap holes, matte launders, slag skim..., installation and proper operation of primary hoods on all active slag and lead bullion furnace tap holes and...

Head-mounted display systems and the special operations soldier

NASA Astrophysics Data System (ADS)

Loyd, Rodney B.

1998-08-01

In 1997, the Boeing Company, working with DARPA under the Smart Modules program and the US Army Soldier Systems Command, embarked on an advanced research and development program to develop a wearable computer system tailored for use with soldiers of the US Special Operations Command. The 'special operations combat management system' is a rugged advanced wearable tactical computer, designed to provide the special operations soldier with enhanced situation awareness and battlefield information capabilities. Many issues must be considered during the design of wearable computers for a combat soldier, including the system weight, placement on the body with respect to other equipment, user interfaces and display system characteristics. During the initial feasibility study for the system, the operational environment was examined and potential users were interviewed to establish the proper display solution for the system. Many display system requirements resulted, such as head or helmet mounting, Night Vision Goggle compatibility, minimal visible light emissions, environmental performance and even the need for handheld or other 'off the head' type display systems. This paper will address these issues and other end user requirements for display systems for applications in the harsh and demanding environment of the Special Operations soldier.

40 CFR 1065.501 - Overview.

Code of Federal Regulations, 2011 CFR

2011-07-01

... engine and sampling systems. (7) Sample emissions throughout the duty cycle. (8) Record post-test data. (9) Perform post-test procedures to verify proper operation of certain equipment and analyzers. (10... PROCEDURES Performing an Emission Test Over Specified Duty Cycles § 1065.501 Overview. (a) Use the procedures...

40 CFR 1065.501 - Overview.

Code of Federal Regulations, 2010 CFR

2010-07-01

... engine and sampling systems. (7) Sample emissions throughout the duty cycle. (8) Record post-test data. (9) Perform post-test procedures to verify proper operation of certain equipment and analyzers. (10... PROCEDURES Performing an Emission Test Over Specified Duty Cycles § 1065.501 Overview. (a) Use the procedures...

40 CFR 1065.501 - Overview.

Code of Federal Regulations, 2014 CFR

2014-07-01

... engine and sampling systems. (7) Sample emissions throughout the duty cycle. (8) Record post-test data. (9) Perform post-test procedures to verify proper operation of certain equipment and analyzers. (10... PROCEDURES Performing an Emission Test Over Specified Duty Cycles § 1065.501 Overview. (a) Use the procedures...

40 CFR 1065.501 - Overview.

Code of Federal Regulations, 2013 CFR

2013-07-01

... engine and sampling systems. (7) Sample emissions throughout the duty cycle. (8) Record post-test data. (9) Perform post-test procedures to verify proper operation of certain equipment and analyzers. (10... PROCEDURES Performing an Emission Test Over Specified Duty Cycles § 1065.501 Overview. (a) Use the procedures...

40 CFR 1065.501 - Overview.

Code of Federal Regulations, 2012 CFR

2012-07-01

... engine and sampling systems. (7) Sample emissions throughout the duty cycle. (8) Record post-test data. (9) Perform post-test procedures to verify proper operation of certain equipment and analyzers. (10... PROCEDURES Performing an Emission Test Over Specified Duty Cycles § 1065.501 Overview. (a) Use the procedures...

Analysis of transit contracting models and proper incentives for long-term success.

DOT National Transportation Integrated Search

2013-11-01

As transit systems are being challenged to operate in the most cost-effective manner, and budgets are being tightened and demand for services increases, there has been renewed interest in the area of contracting for fixed route service in the United ...

Practical Applications of Data Processing to School Purchasing.

ERIC Educational Resources Information Center

California Association of School Business Officials, San Diego. Imperial Section.

Electronic data processing provides a fast and accurate system for handling large volumes of routine data. If properly employed, computers can perform myriad functions for purchasing operations, including purchase order writing; equipment inventory control; vendor inventory; and equipment acquisition, transfer, and retirement. The advantages of…

Operations and Maintenance January Newsletter | Poster

Cancer.gov

One of the many services provided through our Exterior and Structural Systems shop is “Moving” Services. Planning, coordination, and proper paperwork are critical to ensure a successful move. Please read on for some tips and factoids to help guide you through your requests for these services.

A simplification of the fractional Hartley transform applied to image security system in phase

NASA Astrophysics Data System (ADS)

Jimenez, Carlos J.; Vilardy, Juan M.; Perez, Ronal

2017-01-01

In this work we develop a new encryption system for encoded image in phase using the fractional Hartley transform (FrHT), truncation operations and random phase masks (RPMs). We introduce a simplification of the FrHT with the purpose of computing this transform in an efficient and fast way. The security of the encryption system is increased by using nonlinear operations, such as the phase encoding and the truncation operations. The image to encrypt (original image) is encoded in phase and the truncation operations applied in the encryption-decryption system are the amplitude and phase truncations. The encrypted image is protected by six keys, which are the two fractional orders of the FrHTs, the two RPMs and the two pseudorandom code images generated by the amplitude and phase truncation operations. All these keys have to be correct for a proper recovery of the original image in the decryption system. We present digital results that confirm our approach.

High Pressure Coolant Injection (HPCI) System Risk-Based Inspection Guide for Browns Ferry Nuclear Power Station

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wong, S.; DiBiasio, A.; Gunther, W.

1993-09-01

The High Pressure Coolant Injection (HPCI) system has been examined from a risk perspective. A System Risk-Based Inspection Guide (S-RIG) has been developed as an aid to HPCI system inspections at the Browns Ferry Nuclear Power Plant, Units 1, 2 and 3. The role of. the HPCI system in mitigating accidents is discussed in this S-RIG, along with insights on identified risk-based failure modes which could prevent proper operation of the system. The S-RIG provides a review of industry-wide operating experience, including plant-specific illustrative examples to augment the PRA and operational considerations in identifying a catalogue of basic PRA failuremore » modes for the HPCI system. It is designed to be used as a reference for routine inspections, self-initiated safety system functional inspections (SSFIs), and the evaluation of risk significance of component failures at the nuclear power plant.« less

The Joint Master Operational Planner

DTIC Science & Technology

2016-04-04

Operational Planner Program, that will produce planners that are able to understand the strategic- operational environment, properly advise commanders, and...Planner Program, that will produce planners that are able to understand the strategic-operational environment, properly advise commanders, and devise...states struggle to exercise even nominal power within their borders, and the people see the government as an entity that seeks only to keep itself in

Microprocessor tester for the treat upgrade reactor trip system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lenkszus, F.R.; Bucher, R.G.

1984-01-01

The upgrading of the Transient Reactor Test (TREAT) Facility at ANL-Idaho has been designed to provide additional experimental capabilities for the study of core disruptive accident (CDA) phenomena. In addition, a programmable Automated Reactor Control System (ARCS) will permit high-power transients up to 11,000 MW having a controlled reactor period of from 15 to 0.1 sec. These modifications to the core neutronics will improve simulation of LMFBR accident conditions. Finally, a sophisticated, multiply-redundant safety system, the Reactor Trip System (RTS), will provide safe operation for both steady state and transient production operating modes. To insure that this complex safety systemmore » is functioning properly, a Dedicated Microprocessor Tester (DMT) has been implemented to perform a thorough checkout of the RTS prior to all TREAT operations.« less

Diatomite filtration of water for injection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olmsted, B.C. Jr.; Bell, G.R.

1966-01-01

A discussion is presented of the capabilities, problems, and answers, in the performance of diatomite filters. The discussion includes a description of diatomite filtration, new developments, design criteria, and some case histories. Diatomite filters, when properly designed and installed, and when properly applied, can provide effective clarification of waters for injection at low capital and operating costs. Design, installation, and proper application, effectiveness, and capital and operating costs can be placed in the proper perspective in the light of general experience and recent pilot plant tests in the southern California area. (30 refs.)

Authentication System for Electrical Charging of Electrical Vehicles in the Housing Development

NASA Astrophysics Data System (ADS)

Song, Wang-Cheol

Recently the smart grid has been a hot issue in the research area. The Electric Vehicle (EV) is the most important component in the Smart Grid, having a role of the battery component with high capacity. We have thought how to introduce the EV in the housing development, and for proper operation of the smart grid systems in the housing area the authentication system is essential for the individual houses. We propose an authentication system to discriminate an individual houses, so that the account management component can appropriately operate the electrical charging and billing in the housing estate. The proposed system has an architecture to integrate the charging system outside a house and the monitoring system inside a house.

An Application of the Methodology for Assessment of the Sustainability of Air Transport System

NASA Technical Reports Server (NTRS)

Janic, Milan

2003-01-01

An assessment and operationalization of the concept of sustainable air transport system is recognized as an important but complex research, operational and policy task. In the scope of the academic efforts to properly address the problem, this paper aims to assess the sustainability of air transport system. It particular, the paper describes the methodology for assessment of sustainability and its potential application. The methodology consists of the indicator systems, which relate to the air transport system operational, economic, social and environmental dimension of performance. The particular indicator systems are relevant for the particular actors such users (air travellers), air transport operators, aerospace manufacturers, local communities, governmental authorities at different levels (local, national, international), international air transport associations, pressure groups and public. In the scope of application of the methodology, the specific cases are selected to estimate the particular indicators, and thus to assess the system sustainability under given conditions.

The value of supply chain coordination under moral hazard: A case study of the consumer product supply chain.

PubMed

Lee, Yumi; Song, Sang Hwa; Cheong, Taesu

2018-01-01

In this paper, we examine a real-world case related to the consumer product supply chain to analyze the value of supply chain coordination under the condition of moral hazard. Because of the characteristics of a buyback contract scheme employed in the supply chain, the supplier company's sales department encourages retailers to order more inventory to meet their sales target, whereas retailers pay less attention to their inventory level and leftovers at the end of the season. This condition induces moral hazard problems in the operation of the supply chain, as suppliers suffer from huge returns of leftover inventory. This, in turn, is related to the obsolescence of returned inventory, even with penalty terms in the contract for the return of any leftovers. In this study, we show under the current buyback-based supply chain operation, the inventory levels of both the supplier and retailers exceed customer demand and develop vendor-managed inventory (VMI) system with base stock policy to remove any mismatch of supply and demand. A comparison of both systems shows that through the proper coordination of supply chain operations, both suppliers and retailers can gain additional benefits while providing proper services to end customers.

Report: EPA’s and Mississippi’s Efforts to Assess and Restore Public Drinking Water Supplies after Hurricane Katrina

EPA Pesticide Factsheets

Report #2006-P-00011, February 14, 2006. The Mississippi Department of Health and drinking water system operators provided the public with timely and accurate information about the safety and proper treatment of public drinking water supplies.

Analytical Approaches for Identification and Representation of Critical Protection Systems in Transient Stability Studies

NASA Astrophysics Data System (ADS)

Hedman, Mojdeh Khorsand

After a major disturbance, the power system response is highly dependent on protection schemes and system dynamics. Improving power systems situational awareness requires proper and simultaneous modeling of both protection schemes and dynamic characteristics in power systems analysis tools. Historical information and ex-post analysis of blackouts reaffirm the critical role of protective devices in cascading events, thereby confirming the necessity to represent protective functions in transient stability studies. This dissertation is aimed at studying the importance of representing protective relays in power system dynamic studies. Although modeling all of the protective relays within transient stability studies may result in a better estimation of system behavior, representing, updating, and maintaining the protection system data becomes an insurmountable task. Inappropriate or outdated representation of the relays may result in incorrect assessment of the system behavior. This dissertation presents a systematic method to determine essential relays to be modeled in transient stability studies. The desired approach should identify protective relays that are critical for various operating conditions and contingencies. The results of the transient stability studies confirm that modeling only the identified critical protective relays is sufficient to capture system behavior for various operating conditions and precludes the need to model all of the protective relays. Moreover, this dissertation proposes a method that can be implemented to determine the appropriate location of out-of-step blocking relays. During unstable power swings, a generator or group of generators may accelerate or decelerate leading to voltage depression at the electrical center along with generator tripping. This voltage depression may cause protective relay mis-operation and unintentional separation of the system. In order to avoid unintentional islanding, the potentially mis-operating relays should be blocked from tripping with the use of out-of-step blocking schemes. Blocking these mis-operating relays, combined with an appropriate islanding scheme, help avoid a system wide collapse. The proposed method is tested on data from the Western Electricity Coordinating Council. A triple line outage of the California-Oregon Intertie is studied. The results show that the proposed method is able to successfully identify proper locations of out-of-step blocking scheme.

The Spacecraft Emergency Response System (SERS) for Autonomous Mission Operations

NASA Technical Reports Server (NTRS)

Breed, Julia; Chu, Kai-Dee; Baker, Paul; Starr, Cynthia; Fox, Jeffrey; Baitinger, Mick

1998-01-01

Today, most mission operations are geared toward lowering cost through unmanned operations. 7-day/24-hour operations are reduced to either 5-day/8-hour operations or become totally autonomous, especially for deep-space missions. Proper and effective notification during a spacecraft emergency could mean success or failure for an entire mission. The Spacecraft Emergency Response System (SERS) is a tool designed for autonomous mission operations. The SERS automatically contacts on-call personnel as needed when crises occur, either on-board the spacecraft or within the automated ground systems. Plus, the SERS provides a group-ware solution to facilitate the work of the person(s) contacted. The SERS is independent of the spacecraft's automated ground system. It receives and catalogues reports for various ground system components in near real-time. Then, based on easily configurable parameters, the SERS determines whom, if anyone, should be alerted. Alerts may be issued via Sky-Tel 2-way pager, Telehony, or e-mail. The alerted personnel can then review and respond to the spacecraft anomalies through the Netscape Internet Web Browser, or directly review and respond from the Sky-Tel 2-way pager.

Artificial intelligence applied to process signal analysis

NASA Technical Reports Server (NTRS)

Corsberg, Dan

1988-01-01

Many space station processes are highly complex systems subject to sudden, major transients. In any complex process control system, a critical aspect of the human/machine interface is the analysis and display of process information. Human operators can be overwhelmed by large clusters of alarms that inhibit their ability to diagnose and respond to a disturbance. Using artificial intelligence techniques and a knowledge base approach to this problem, the power of the computer can be used to filter and analyze plant sensor data. This will provide operators with a better description of the process state. Once a process state is recognized, automatic action could be initiated and proper system response monitored.

Study of application of space telescope science operations software for SIRTF use

NASA Technical Reports Server (NTRS)

Dignam, F.; Stetson, E.; Allendoerfer, W.

1985-01-01

The design and development of the Space Telescope Science Operations Ground System (ST SOGS) was evaluated to compile a history of lessons learned that would benefit NASA's Space Infrared Telescope Facility (SIRTF). Forty-nine specific recommendations resulted and were categorized as follows: (1) requirements: a discussion of the content, timeliness and proper allocation of the system and segment requirements and the resulting impact on SOGS development; (2) science instruments: a consideration of the impact of the Science Instrument design and data streams on SOGS software; and (3) contract phasing: an analysis of the impact of beginning the various ST program segments at different times. Approximately half of the software design and source code might be useable for SIRTF. Transportability of this software requires, at minimum, a compatible DEC VAX-based architecture and VMS operating system, system support software similar to that developed for SOGS, and continued evolution of the SIRTF operations concept and requirements such that they remain compatible with ST SOGS operation.

Performance Monitoring and Assessment of Neuro-Adaptive Controllers for Aerospace Applications Using a Bayesian Approach

NASA Technical Reports Server (NTRS)

Gupta, Pramod; Guenther, Kurt; Hodgkinson, John; Jacklin, Stephen; Richard, Michael; Schumann, Johann; Soares, Fola

2005-01-01

Modern exploration missions require modern control systems-control systems that can handle catastrophic changes in the system's behavior, compensate for slow deterioration in sustained operations, and support fast system ID. Adaptive controllers, based upon Neural Networks have these capabilities, but they can only be used safely if proper verification & validation (V&V) can be done. In this paper we present our V & V approach and simulation result within NASA's Intelligent Flight Control Systems (IFCS).

[Quality Improvement Project: Increasing the Rate of Proper Use of Infant Transferring Warmers].

PubMed

Huang, Hsiu-Yu; Fann, Guei-Ling

2015-10-01

Infant-transferring warmers provide a warm environment and emergency care facilities such ventilators for high-risk infants during transport. Accurate use of this warmer has been demonstrated to reduce rates of neonatal complications and increase rates of survival. This project found that, despite the complaints of nurses that warmers occasionally malfunctioned during the transfer process, warmer functions nearly always tested normal after use. Therefore, the researchers surveyed ward nurses to better understand the underlying reasons for these complaints. Results found that only 68.4% of those surveyed operated the warmer correctly. The reasons for improper use were analyzed and categorized as: Nurse-related factors - lack of warmer operating knowledge and experience in the clinic; System-related factors - lack of a standard operating procedure (SOP) and monitor/audit practices and an incomplete training protocol; Equipment-related factors - lack of an equipment preparation SOP and difficulties in setting the ventilator properly. The purpose of this project was to achieve a 100% rate of proper warmer use among nurses. Through continuous clinical education, we created a standard operating procedure for warmer operation, created a video and poster for warmer users, simplified the equipment preparation SOP, and periodically monitored and checked results. After the intervention, 100% of the nurses were able to use the warmers correctly. Additionally, the rate of satisfaction for nursing-warmer use among the participating nurses increased from 51.4% to 80.6%. This project effectively increased the rate for correctly using transferring warmers among participating nurses and improved the quality of medical care.

40 CFR 94.1004 - Maintenance, repair, adjustment, and recordkeeping.

Code of Federal Regulations, 2010 CFR

2010-07-01

... alteration before the emission-control system is restored to proper functioning. The provisions of paragraph... be signed by the executive with responsibility for marine activities of the owner. If the vessel is... executive(s) may authorize a captain or other primary operator to conduct this review and submit the...

46 CFR 63.25-7 - Exhaust gas boilers.

Code of Federal Regulations, 2012 CFR

2012-10-01

... exceeds the maximum operating temperature or when the fluid/steam flowing through the heat exchanger is... water level, the control system must supply the feed water at a rate sufficient to ensure proper heat... results in inadequate heat transfer, a high temperature alarm or low flow alarm must be activated. An...

46 CFR 63.25-7 - Exhaust gas boilers.

Code of Federal Regulations, 2014 CFR

2014-10-01

... exceeds the maximum operating temperature or when the fluid/steam flowing through the heat exchanger is... water level, the control system must supply the feed water at a rate sufficient to ensure proper heat... results in inadequate heat transfer, a high temperature alarm or low flow alarm must be activated. An...

46 CFR 63.25-7 - Exhaust gas boilers.

Code of Federal Regulations, 2013 CFR

2013-10-01

... exceeds the maximum operating temperature or when the fluid/steam flowing through the heat exchanger is... water level, the control system must supply the feed water at a rate sufficient to ensure proper heat... results in inadequate heat transfer, a high temperature alarm or low flow alarm must be activated. An...

Effects of elevated carbon dioxide concentrations on broiler chicken performance from 28 to 49 days

USDA-ARS?s Scientific Manuscript database

Improvements in modern broiler housing have substantially reduced air leakage, making proper operation of ventilation systems critical to maintaining a suitable environment. Fuel prices have increased in recent years, leading to reduced minimum ventilation in order to conserve fuel which increases ...

76 FR 60030 - Information Collections Being Reviewed by the Federal Communications Commission

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-28

... Number: 3060-0161. Title: Section 73.61, AM Directional Antenna Field Strength Measurements. Form Number...). Needs and Uses: 47 CFR Section 73.61 requires that each AM station using directional antennas to make field strength measurement as often as necessary to ensure proper directional antenna system operation...

Update on the Status of Sanitary Sewer Overflow Analysis and Planning (SSOAP) Toolbox

EPA Science Inventory

A properly designed, operated and maintained sanitary sewer system is meant to collect and convey all of the sewage that flows into it to a wastewater treatment plant. However, occasional unintentional discharges of raw sewage from municipal sanitary sewers – called sanitary sewe...

Land application of organic residuals: Public health threat or environmental benefit

USDA-ARS?s Scientific Manuscript database

Waste residuals consist of manure and biosolids produced by concentrated animal feeding operations and municipal waste water treatment plants. All wastes need to be disposed of in a proper manner, protecting public and environmental health, but also in a sustainable fashion to ensure that no system...

Safety and Suitability for Service Assessment Testing of Large Caliber Ammunition Greater Than 40MM

DTIC Science & Technology

2013-07-02

2 July 2013 2 Page Paragraph 9.2 Insensitive Munitions Assessment ........................................ 14 9.3 Munition Software System ...encounter during storage and transportation. 3.12 Weapon System . A weapon and those components required for its operation, comprising the aggregate of...Provide a positive indexing system on the cartridge case to ensure proper orientation of the case when it is loaded into the weapon. 6.9 Weapon

Implementing Information Assurance - Beyond Process

DTIC Science & Technology

2009-01-01

disabled or properly configured. Tools and scripts are available to expedite the configuration process on some platforms, For example, approved Windows...in the System Security Plan (SSP) or Information Security Plan (lSP). Any PPSs not required for operation by the system must be disabled , This...Services must be disabled , Implementing an 1M capability within the boundary carries many policy and documentation requirements. Usemame and passwords

Cyber-Defense Return on Investment for NAVFAC Energy Technologies

DTIC Science & Technology

2017-12-01

Stakeholder input is important to properly develop a tool that reflects the legitimate concerns of those who routinely design , operate, and use control ...cybersecurity results with no control system network connectivity at all. Both are extreme scenarios, unless electrical engineers can design a...support of a Department of Defense (DOD) effort to improve cyber- security in relation to DOD installation control systems. Space and Naval Warfare

Server-Based and Server-Less Byod Solutions to Support Electronic Learning

DTIC Science & Technology

2016-06-01

Knowledge Online NSD National Security Directive OS operating system OWA Outlook Web Access PC personal computer PED personal electronic device PDA...mobile devices, institute mobile device policies and standards, and promote the development and use of DOD mobile and web -enabled applications” (DOD...with an isolated BYOD web server, properly educated system administrators must carry out and execute the necessary, pre-defined network security

An Empirical Methodology for Engineering Human Systems Integration

DTIC Science & Technology

2009-12-01

scanning critical information and selectively skipping what is not important for the immediate task. This learned skill is called a proper “cross check...ability to recover from errors. Efficiency: the level of productivity that can be achieved once learning has occurred. 162 Learnability: the...use, to legacy systems. Knowing what design issues have plagued past operators can guide the generation of requirements to address the identified

29 CFR 1926.1412 - Inspections.

Code of Federal Regulations, 2013 CFR

2013-07-01

... conditions, and proper operation. (vii) Chains and chain drive sprockets for excessive wear of sprockets and excessive chain stretch. (viii) Travel steering, brakes, and locking devices, for proper operation. (ix... decals originally supplied with the equipment by the manufacturer or otherwise required under this...

29 CFR 1926.1412 - Inspections.

Code of Federal Regulations, 2014 CFR

2014-07-01

... conditions, and proper operation. (vii) Chains and chain drive sprockets for excessive wear of sprockets and excessive chain stretch. (viii) Travel steering, brakes, and locking devices, for proper operation. (ix... decals originally supplied with the equipment by the manufacturer or otherwise required under this...

29 CFR 1926.1412 - Inspections.

Code of Federal Regulations, 2012 CFR

2012-07-01

... conditions, and proper operation. (vii) Chains and chain drive sprockets for excessive wear of sprockets and excessive chain stretch. (viii) Travel steering, brakes, and locking devices, for proper operation. (ix... decals originally supplied with the equipment by the manufacturer or otherwise required under this...

29 CFR 1926.1412 - Inspections.

Code of Federal Regulations, 2011 CFR

2011-07-01

... conditions, and proper operation. (vii) Chains and chain drive sprockets for excessive wear of sprockets and excessive chain stretch. (viii) Travel steering, brakes, and locking devices, for proper operation. (ix... decals originally supplied with the equipment by the manufacturer or otherwise required under this...

Medical records and issues in negligence

PubMed Central

Thomas, Joseph

2009-01-01

It is very important for the treating doctor to properly document the management of a patient under his care. Medical record keeping has evolved into a science of itself. This will be the only way for the doctor to prove that the treatment was carried out properly. Moreover, it will also be of immense help in the scientific evaluation and review of patient management issues. Medical records form an important part of the management of a patient. It is important for the doctors and medical establishments to properly maintain the records of patients for two important reasons. The first one is that it will help them in the scientific evaluation of their patient profile, helping in analyzing the treatment results, and to plan treatment protocols. It also helps in planning governmental strategies for future medical care. But of equal importance in the present setting is in the issue of alleged medical negligence. The legal system relies mainly on documentary evidence in a situation where medical negligence is alleged by the patient or the relatives. In an accusation of negligence, this is very often the most important evidence deciding on the sentencing or acquittal of the doctor. With the increasing use of medical insurance for treatment, the insurance companies also require proper record keeping to prove the patient's demand for medical expenses. Improper record keeping can result in declining medical claims. It is disheartening to note that inspite of knowing the importance of proper record keeping it is still in a nascent stage in India. It is wise to remember that “Poor records mean poor defense, no records mean no defense”. Medical records include a variety of documentation of patient's history, clinical findings, diagnostic test results, preoperative care, operation notes, post operative care, and daily notes of a patient's progress and medications. A properly obtained consent will go a long way in proving that the procedures were conducted with the concurrence of the patient. A properly written operative note can protect a surgeon in case of alleged negligence due to operative complications. It is important that the prescription for drugs should be legible with the name of the patient, date, and the signature of the doctor. An undated prescription can land a doctor in trouble if the patient misuses it. There are also many records that are indirectly related to patient management such as accounts records, service records of the staff, and administrative records, which are also useful as evidences for litigation purposes. Medical recording needs the concerted effort of a number of people involved in patient care. The doctor is the prime person who has to oversee this process and is primarily responsible for history, physical examination, treatment plans, operative records, consent forms, medications used, referral papers, discharge records, and medical certificates. There should be proper recording of nursing care, laboratory data, reports of diagnostic evaluations, pharmacy records, and billing processes. This means that the paramedical and nursing staff also should be trained in proper maintenance of patient records. The medical scene in India extends from smaller clinics to large hospitals. Medical record keeping is a specialized area in bigger teaching and corporate hospitals with separate medical records officers handling these issues. However, it is yet to develop into a proper process in the large number of smaller clinics and hospitals that cater to a large section of the people in India. PMID:19881136

WASTE HANDLING BUILDING VENTILATION SYSTEM DESCRIPTION DOCUMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

P.A. Kumar

2000-06-21

The Waste Handling Building Ventilation System provides heating, ventilation, and air conditioning (HVAC) for the contaminated, potentially contaminated, and uncontaminated areas of the Monitored Geologic Repository's (MGR) Waste Handling Building (WHB). In the uncontaminated areas, the non-confinement area ventilation system maintains the proper environmental conditions for equipment operation and personnel comfort. In the contaminated and potentially contaminated areas, in addition to maintaining the proper environmental conditions for equipment operation and personnel comfort, the contamination confinement area ventilation system directs potentially contaminated air away from personnel in the WHB and confines the contamination within high-efficiency particulate air (HEPA) filtration units. Themore » contamination confinement areas ventilation system creates airflow paths and pressure zones to minimize the potential for spreading contamination within the building. The contamination confinement ventilation system also protects the environment and the public by limiting airborne releases of radioactive or other hazardous contaminants from the WHB. The Waste Handling Building Ventilation System is designed to perform its safety functions under accident conditions and other Design Basis Events (DBEs) (such as earthquakes, tornadoes, fires, and loss of the primary electric power). Additional system design features (such as compartmentalization with independent subsystems) limit the potential for cross-contamination within the WHB. The system provides status of important system parameters and equipment operation, and provides audible and/or visual indication of off-normal conditions and equipment failures. The Waste Handling Building Ventilation System confines the radioactive and hazardous material within the building such that the release rates comply with regulatory limits. The system design, operations, and maintenance activities incorporate ALARA (as low as is reasonably achievable) principles to maintain personnel radiation doses to all occupational workers below regulatory limits and as low as is reasonably achievable. The Waste Handling Building Ventilation System interfaces with the Waste Handling Building System by being located within the WHB and by maintaining specific pressures, temperatures, and humidity within the building. The system also depends on the WHB for water supply. The system interfaces with the Site Radiological Monitoring System for continuous monitoring of the exhaust air; the Waste Handling Building Fire Protection System for detection of fire and smoke; the Waste Handling Building Electrical System for normal, emergency, and standby power; and the Monitored Geologic Repository Operations Monitoring and Control System for monitoring and control of the system.« less

Civil use of night vision goggles within the National Airspace System

NASA Astrophysics Data System (ADS)

Winkel, James G.; Faber, Lorelei

2001-08-01

When properly employed, Night Vision Goggles (NVGs) improve a pilot's ability to see during periods of darkness. The resultant enhancement in situational awareness achieved when using NVGs, increases light safety during night VFR operations. FAA is constrained with a lack of requisite regulatory and guidance infrastructure to adequately facilitate the civil request for use in NVGs within the National Airspace System (NAS) Appliances and Equipment, is formed and tasked to develop: operational concept and operational requirements for NVG implementation into the NAS, minimum operational performance standards for NVGs, and training guidelines and considerations for NVG operations. This paper provides a historical perspective on use of NVGs within the NAS, the status of SC-196 work in progress, FAA integration of SC-196 committee products and the harmonization effort between EUROCAEs NVG committee and SC- 196.

Review & Peer Review of “Parameters for Properly Designed and Operated Flares” Documents

EPA Pesticide Factsheets

This page contains two 2012 memoranda on the review of EPA's parameters for properly designed and operated flares. One details the process of peer review, and the other provides background information and specific charge questions to the panel.

High level language-based robotic control system

NASA Technical Reports Server (NTRS)

Rodriguez, Guillermo (Inventor); Kruetz, Kenneth K. (Inventor); Jain, Abhinandan (Inventor)

1994-01-01

This invention is a robot control system based on a high level language implementing a spatial operator algebra. There are two high level languages included within the system. At the highest level, applications programs can be written in a robot-oriented applications language including broad operators such as MOVE and GRASP. The robot-oriented applications language statements are translated into statements in the spatial operator algebra language. Programming can also take place using the spatial operator algebra language. The statements in the spatial operator algebra language from either source are then translated into machine language statements for execution by a digital control computer. The system also includes the capability of executing the control code sequences in a simulation mode before actual execution to assure proper action at execution time. The robot's environment is checked as part of the process and dynamic reconfiguration is also possible. The languages and system allow the programming and control of multiple arms and the use of inward/outward spatial recursions in which every computational step can be related to a transformation from one point in the mechanical robot to another point to name two major advantages.

High level language-based robotic control system

NASA Technical Reports Server (NTRS)

Rodriguez, Guillermo (Inventor); Kreutz, Kenneth K. (Inventor); Jain, Abhinandan (Inventor)

1996-01-01

This invention is a robot control system based on a high level language implementing a spatial operator algebra. There are two high level languages included within the system. At the highest level, applications programs can be written in a robot-oriented applications language including broad operators such as MOVE and GRASP. The robot-oriented applications language statements are translated into statements in the spatial operator algebra language. Programming can also take place using the spatial operator algebra language. The statements in the spatial operator algebra language from either source are then translated into machine language statements for execution by a digital control computer. The system also includes the capability of executing the control code sequences in a simulation mode before actual execution to assure proper action at execution time. The robot's environment is checked as part of the process and dynamic reconfiguration is also possible. The languages and system allow the programming and control of multiple arms and the use of inward/outward spatial recursions in which every computational step can be related to a transformation from one point in the mechanical robot to another point to name two major advantages.

WORK SAFETY CONDITIONS WITH CLOSED RADIATION SOURCES (in Polish)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brosziewicz, R.

1963-01-01

A discussion is presented of principles of radiological protection observed in the Radiation Chemistry Dept. of the Nuclear Research Inst., during operation of large sources of ionizing radiation. It has been revealed that a properly designed servicing system of these sources ensures full protection of personnel even with not fully protected sources. (auth)

36 CFR 4.15 - Safety belts.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false Safety belts. 4.15 Section 4... TRAFFIC SAFETY § 4.15 Safety belts. (a) Each operator and passenger occupying any seating position of a motor vehicle in a park area will have the safety belt or child restraint system properly fastened at...

7 CFR 3560.103 - Maintaining housing projects.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., floors, and ceilings that are free of holes, evidence of current water leaks, and free of material that... which are operating properly, free of leaks, supply adequate hot water, and are fitted with temperature... malfunctions of equipment or damages to building systems such as a furnace breakdown or a water leak; and (iii...

Priority issues for hospital boards.

PubMed

Middleton, E George

2005-01-01

Governing a hospital or healthcare system is a difficult and demanding job. If done properly, the organization can operate well. If the board is inept or incompetent, the organization will suffer. In this article I discuss those functions of board governance that I think are among the most important, along with some recommendations for implementing them.

76 FR 75880 - Information Collections Being Submitted for Review and Approval to the Office of Management and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-05

...: 3060-0161. Title: Section 73.61, AM Directional Antenna Field Strength Measurements. Form Number: N/A... CFR 73.61 requires that each AM station using directional antennas to make field strength measurement as often as necessary to ensure proper directional antenna system operation. Stations not having...

36 CFR 4.15 - Safety belts.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Safety belts. 4.15 Section 4... TRAFFIC SAFETY § 4.15 Safety belts. (a) Each operator and passenger occupying any seating position of a motor vehicle in a park area will have the safety belt or child restraint system properly fastened at...

Non-radiation induced signals in TL dosimetry.

PubMed

German, U; Weinstein, M

2002-01-01

One source of background signals, which are non-radiation related, is the reader system and it includes dark current, external contaminants and electronic spikes. These factors can induce signals equivalent to several hundredths of mSv. Mostly, the effects are minimised by proper design of the TLD reader, but some effects are dependent on proper operation of the system. The other main group of background signals originates in the TL crystal and is due to tribothermoluminescence, dirt, chemical reactions and stimulation by visible or UV light. These factors can have a significant contribution, equivalent to over several mSv, depending on whether the crystal is bare or protected by PTFE. Working in clean environments, monitoring continuously the glow curves and performing glow curve deconvolution are suggested to minimise non-radiation induced spurious signals.

Methods, systems and apparatus for adjusting duty cycle of pulse width modulated (PWM) waveforms

DOEpatents

Gallegos-Lopez, Gabriel; Kinoshita, Michael H; Ransom, Ray M; Perisic, Milun

2013-05-21

Embodiments of the present invention relate to methods, systems and apparatus for controlling operation of a multi-phase machine in a vector controlled motor drive system when the multi-phase machine operates in an overmodulation region. The disclosed embodiments provide a mechanism for adjusting a duty cycle of PWM waveforms so that the correct phase voltage command signals are applied at the angle transitions. This can reduce variations/errors in the phase voltage command signals applied to the multi-phase machine so that phase current may be properly regulated thus reducing current/torque oscillation, which can in turn improve machine efficiency and performance, as well as utilization of the DC voltage source.

Mechanical code comparator

DOEpatents

Peter, Frank J.; Dalton, Larry J.; Plummer, David W.

2002-01-01

A new class of mechanical code comparators is described which have broad potential for application in safety, surety, and security applications. These devices can be implemented as micro-scale electromechanical systems that isolate a secure or otherwise controlled device until an access code is entered. This access code is converted into a series of mechanical inputs to the mechanical code comparator, which compares the access code to a pre-input combination, entered previously into the mechanical code comparator by an operator at the system security control point. These devices provide extremely high levels of robust security. Being totally mechanical in operation, an access control system properly based on such devices cannot be circumvented by software attack alone.

A mixed-modem solution for sensitive data segregation on a broadband network

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crutcher, R.I.; Ewing, P.D.

1988-01-01

Data isolation is required in broadband networks to prevent unauthorized access to the sensitive data of other users. Isolation can be obtained by using equipment from different manufacturers to introduce incompatibility between nonassociated users. This paper develops the basis for isolation and postulates that four layers of ioslation will exist when the proper equipment is chosen. An experimental broadband local area network (LAN) was constructed to verify isolation. This independent test system allowed variations to network operating conditions without causing interference to normal broadband operations. The measured results indicate that a broadband LAN can transmit data of varying sensitivity levelsmore » without compromising data security. When combined with the proper administrative restrictions, the mixed-modem technique provides a cost-effective method of sharing a broadband network while maintaining isolation of data having different sensitivities. 6 refs., 3 figs.« less

A Generalized Method for Automatic Downhand and Wirefeed Control of a Welding Robot and Positioner

NASA Technical Reports Server (NTRS)

Fernandez, Ken; Cook, George E.

1988-01-01

A generalized method for controlling a six degree-of-freedom (DOF) robot and a two DOF positioner used for arc welding operations is described. The welding path is defined in the part reference frame, and robot/positioner joint angles of the equivalent eight DOF serial linkage are determined via an iterative solution. Three algorithms are presented: the first solution controls motion of the eight DOF mechanism such that proper torch motion is achieved while minimizing the sum-of-squares of joint displacements; the second algorithm adds two constraint equations to achieve torch control while maintaining part orientation so that welding occurs in the downhand position; and the third algorithm adds the ability to control the proper orientation of a wire feed mechanism used in gas tungsten arc (GTA) welding operations. A verification of these algorithms is given using ROBOSIM, a NASA developed computer graphic simulation software package design for robot systems development.

The value of supply chain coordination under moral hazard: A case study of the consumer product supply chain

PubMed Central

Lee, Yumi; Song, Sang Hwa

2018-01-01

In this paper, we examine a real-world case related to the consumer product supply chain to analyze the value of supply chain coordination under the condition of moral hazard. Because of the characteristics of a buyback contract scheme employed in the supply chain, the supplier company’s sales department encourages retailers to order more inventory to meet their sales target, whereas retailers pay less attention to their inventory level and leftovers at the end of the season. This condition induces moral hazard problems in the operation of the supply chain, as suppliers suffer from huge returns of leftover inventory. This, in turn, is related to the obsolescence of returned inventory, even with penalty terms in the contract for the return of any leftovers. In this study, we show under the current buyback-based supply chain operation, the inventory levels of both the supplier and retailers exceed customer demand and develop vendor-managed inventory (VMI) system with base stock policy to remove any mismatch of supply and demand. A comparison of both systems shows that through the proper coordination of supply chain operations, both suppliers and retailers can gain additional benefits while providing proper services to end customers. PMID:29547625

Real-time data collection in Linux: a case study.

PubMed

Finney, S A

2001-05-01

Multiuser UNIX-like operating systems such as Linux are often considered unsuitable for real-time data collection because of the potential for indeterminate timing latencies resulting from preemptive scheduling. In this paper, Linux is shown to be fully adequate for precisely controlled programming with millisecond resolution or better. The Linux system calls that subserve such timing control are described and tested and then utilized in a MIDI-based program for tapping and music performance experiments. The timing of this program, including data input and output, is shown to be accurate at the millisecond level. This demonstrates that Linux, with proper programming, is suitable for real-time experiment software. In addition, the detailed description and test of both the operating system facilities and the application program itself may serve as a model for publicly documenting programming methods and software performance on other operating systems.

Controllability of Free-piston Stirling Engine/linear Alternator Driving a Dynamic Load

NASA Technical Reports Server (NTRS)

Kankam, M. David; Rauch, Jeffrey S.

1994-01-01

This paper presents the dynamic behavior of a Free-Piston Stirling Engine/linear alternator (FPSE/LA) driving a single-phase fractional horse-power induction motor. The controllability and dynamic stability of the system are discussed by means of sensitivity effects of variations in system parameters, engine controller, operating conditions, and mechanical loading on the induction motor. The approach used expands on a combined mechanical and thermodynamic formulation employed in a previous paper. The application of state-space technique and frequency domain analysis enhances understanding of the dynamic interactions. Engine-alternator parametric sensitivity studies, similar to those of the previous paper, are summarized. Detailed discussions are provided for parametric variations which relate to the engine controller and system operating conditions. The results suggest that the controllability of a FPSE-based power system is enhanced by proper operating conditions and built-in controls.

High Resolution Modeling of Coastal Inundation: User Requirements and Current Practice, A Navy Perspective

DTIC Science & Technology

2007-07-27

often located at Within this paper the general role of in- period. These changes in the operational ret- the cusp of the land- sea interface where algo...vegetation, and sediment proper- summarizes the user requirements set forth NNS060820-01, www.news.navy.mil). Fur- ties. Since the Navy operational...role are dis- modeling the circulation and pollutant trans- bal, regional, and local systems with two pri- cussed below, port in estuarine and coastal

43 CFR 3162.7-1 - Disposition of production.

Code of Federal Regulations, 2012 CFR

2012-10-01

... with applicable orders and notices. In the absence of prior approval from the authorized officer, no... for the load of oil. (4) Any authorized representative who is properly identified and who is... driver possesses proper documentation for the load of oil. (d) The operator shall conduct operations in...

43 CFR 3162.7-1 - Disposition of production.

Code of Federal Regulations, 2011 CFR

2011-10-01

... with applicable orders and notices. In the absence of prior approval from the authorized officer, no... for the load of oil. (4) Any authorized representative who is properly identified and who is... driver possesses proper documentation for the load of oil. (d) The operator shall conduct operations in...

43 CFR 3162.7-1 - Disposition of production.

Code of Federal Regulations, 2014 CFR

2014-10-01

... with applicable orders and notices. In the absence of prior approval from the authorized officer, no... for the load of oil. (4) Any authorized representative who is properly identified and who is... driver possesses proper documentation for the load of oil. (d) The operator shall conduct operations in...

43 CFR 3162.7-1 - Disposition of production.

Code of Federal Regulations, 2013 CFR

2013-10-01

... with applicable orders and notices. In the absence of prior approval from the authorized officer, no... for the load of oil. (4) Any authorized representative who is properly identified and who is... driver possesses proper documentation for the load of oil. (d) The operator shall conduct operations in...

Coil spring venting arrangement

DOEpatents

McCugh, R.M.

1975-10-21

A simple venting device for trapped gas pockets in hydraulic systems is inserted through a small access passages, operated remotely, and removed completely. The device comprises a small diameter, closely wound coil spring which is pushed through a guide temporarily inserted in the access passage. The guide has a central passageway which directs the coil spring radially upward into the pocket, so that, with the guide properly positioned for depth and properly oriented, the coil spring can be pushed up into the top of the pocket to vent it. By positioning a seal around the free end of the guide, the spring and guide are removed and the passage is sealed.

Radiation exposure to the operator performing cardiac angiography with U-arm systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balter, S.; Sones, F.M. Jr.; Brancato, R.

The radiation exposure received by a group of operators performing 700 coronary angiograms was measured using the brachial artery approach and the Philips Cardio Diagnost. Nineteen sites were monitored on each operator, using lithium fluoride thermoluminescent dosimeters. Four hundred examinations were performed with a table-mounted protective shield in place. Three hundred were performed without the shield. The average exposures (in mR per study) with and without the shield were 1.9/6 for the eyes and 1.4/8.3 for the thyroid. The resulting operator exposure with the shield in place is low enough so that an operator performing 25 procedures per week onmore » a continuous basis will not exceed the recommendations of the National Commission on Radiological Protection and Units. We therefore strongly recommend the use of properly designed and appropriately positioned shield with all U-arm systems.« less

Radiation exposure to the operator performing cardiac angiography with U-arm systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balter, S.; Sones, F.M. Jr.; Brancato, R.

We measured the radiation exposure received by a group of operators performing 700 coronary angiograms. All studies were performed using the brachial artery approach and the Philips Cardio Diagnost. Nineteen sites were monitored on each operator, using lithium fluoride thermoluminescent dosimeters. Four hundred examinations were performed with a table-mounted protective shield in place. Three hundred were performed without the shield. The averge exposures (in mR per study) with and without the shield were 1.9/6 for the eyes and 1.4/8.3 for the thyroid. The resulting operator exposure with the shield in place is low enough so that an operator performing 25more » procedures per week on a continuous basis will not exceed the recommendations of the National Commission on Radiological Protection and Units. We therefore strongly recommend the use of properly designed and appropriately positioned shield with all U-arm systems.« less

The balloon and the airship technological heritage

NASA Technical Reports Server (NTRS)

Mayer, N. J.

1981-01-01

The balloon and the airship are discussed with emphasis on the identification of commonalities and distinctions. The aerostat technology behind the shape and structure of the vehicles is reviewed, including a discussion of structural weight, internal pressure, buckling, and the development of a stable tethered balloon system. Proper materials for the envelope are considered, taking elongation and stress into account, and flight operation and future developments are reviewed. Airships and tethered balloons which are designed to carry high operating pressure with low gas loss characteristics are found to share similar problems in low speed flight operations, while possessing interchangeable technologies.

Developments in Test Facility and Data Networking for the Altitude Test Stand at the John C. Stennis Space Center: A General Overview

NASA Technical Reports Server (NTRS)

Hebert, Phillip W.

2008-01-01

NASA/SSC's Mission in Rocket Propulsion Testing Is to Acquire Test Performance Data for Verification, Validation and Qualification of Propulsion Systems Hardware: Accurate, Reliable, Comprehensive, and Timely. Data Acquisition in a Rocket Propulsion Test Environment Is Challenging: a) Severe Temporal Transient Dynamic Environments; b) Large Thermal Gradients; c) Vacuum to high pressure regimes. A-3 Test Stand Development is equally challenging with respect to accommodating vacuum environment, operation of a CSG system, and a large quantity of data system and control channels to determine proper engine performance as well as Test Stand operation. SSC is currently in the process of providing modernized DAS, Control Systems, Video, and network systems for the A-3 Test Stand to overcome these challenges.

A Study of the Ethernet Troughput Performance of the Embedded System

NASA Astrophysics Data System (ADS)

Duan, Zhi-Yu; Zhao, Zhao-Wang

2007-09-01

An ethernet acceleration solution developed for the NIOS II Embedded System in astronomical applications - Mason Express is introduced in this paper. By manually constructing the proper network protocol headers and directly driving the hardware, Mason Express goes around the performance bottleneck of the Light Weighted IP stack (LWIP), and achieves up to 90Mb/s unidirectional data troughput rate from the embedded system board to the data collecting computer. With the LWIP stack, the maximum data rate is about 10.57Mb/s. Mason Express is a total software solution and no hardware changes required, neither does it affect the uCOS II operating system nor the LWIP stack, and can be implemented with or without any embedded operating system. It maximally protects the intelligence investment of the users.

Application of voltage oriented control technique in a fully renewable, wind powered, autonomous system with storage capabilities

NASA Astrophysics Data System (ADS)

Kondylis, Georgios P.; Vokas, Georgios A.; Anastasiadis, Anestis G.; Konstantinopoulos, Stavros A.

2017-02-01

The main purpose of this paper is to examine the technological feasibility of a small autonomous network, with electricity storage capability, which is completely electrified by wind energy. The excess energy produced, with respect to the load requirements, is sent to the batteries for storage. When the energy produced by the wind generator is not sufficient, load's energy requirement is covered by the battery system, ensuring, however, that voltage, frequency and other system characteristics are within the proper boundaries. For the purpose of this study, a Voltage Oriented Control system has been developed in order to monitor the autonomous operation and perform the energy management of the network. This system manages the power flows between the load and the storage system by properly controlling the Pulse Width Modulation pulses in the converter, thus ensuring power flows are adequate and frequency remains under control. The experimental results clearly indicate that a stand-alone wind energy system based on battery energy storage system is feasible and reliable. This paves the way for fully renewable and zero emission energy schemes.

Issues of Exploitation of Induction Motors in the Course of Underground Mining Operations

NASA Astrophysics Data System (ADS)

Gumula, Stanisław; Hudy, Wiktor; Piaskowska-Silarska, Malgorzata; Pytel, Krzysztof

2017-09-01

Mining industry is one of the most important customers of electric motors. The most commonly used in the contemporary mining industry is alternating current machines used for processing electrical energy into mechanical energy. The operating problems and the influence of qualitative interference acting on the inputs of individual regulators to field-oriented system in the course of underground mining operations has been presented in the publication. The object of controlling the speed is a slip-ring induction motor. Settings of regulators were calculated using an evolutionary algorithm. Examination of system dynamics was performed by a computer with the use of the MATLAB / Simulink software. According to analyzes, large distortion of input signals of regulators adversely affects the rotational speed that pursued by the control system, which may cause a large vibration of the whole system and, consequently, its much faster destruction. Designed system is characterized by a significantly better resistance to interference. The system is stable with the properly selected settings of regulators, which is particularly important during the operation of machinery used in underground mining.

Strengthening the Security of ESA Ground Data Systems

NASA Astrophysics Data System (ADS)

Flentge, Felix; Eggleston, James; Garcia Mateos, Marc

2013-08-01

A common approach to address information security has been implemented in ESA's Mission Operations (MOI) Infrastructure during the last years. This paper reports on the specific challenges to the Data Systems domain within the MOI and how security can be properly managed with an Information Security Management System (ISMS) according to ISO 27001. Results of an initial security risk assessment are reported and the different types of security controls that are being implemented in order to reduce the risks are briefly described.

Operational test report -- Project W-320 cathodic protection systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowman, T.J.

1998-06-16

Washington Administrative Code (WAC) 173-303-640 specifies that corrosion protection must be designed into tank systems that treat or store dangerous wastes. Project W-320, Waste Retrieval Sluicing System (WRSS), utilizes underground encased waste transfer piping between tanks 241-C-106 and 241-AY-102. Corrosion protection is afforded to the encasements of the WRSS waste transfer piping through the application of earthen ionic currents onto the surface of the piping encasements. Cathodic protection is used in conjunction with the protective coatings that are applied upon the WRSS encasement piping. WRSS installed two new two rectifier systems (46 and 47) and modified one rectifier system (31).more » WAC 173-303-640 specifies that the proper operation of cathodic protection systems must be confirmed within six months after initial installation. The WRSS cathodic protection systems were energized to begin continuous operation on 5/5/98. Sixteen days after the initial steady-state start-up of the WRSS rectifier systems, the operational testing was accomplished with procedure OTP-320-006 Rev/Mod A-0. This operational test report documents the OTP-320-006 results and documents the results of configuration testing of integrated piping and rectifier systems associated with the W-320 cathodic protection systems.« less

SOI N-Channel Field Effect Transistors, CHT-NMOS80, for Extreme Temperatures

NASA Technical Reports Server (NTRS)

Patterson, Richard L.; Hammoud, Almad

2009-01-01

Extreme temperatures, both hot and cold, are anticipated in many of NASA space exploration missions as well as in terrestrial applications. One can seldom find electronics that are capable of operation under both regimes. Even for operation under one (hot or cold) temperature extreme, some thermal controls need to be introduced to provide appropriate ambient temperatures so that spacecraft on-board or field on-site electronic systems work properly. The inclusion of these controls, which comprise of heating elements and radiators along with their associated structures, adds to the complexity in the design of the system, increases cost and weight, and affects overall reliability. Thus, it would be highly desirable and very beneficial to eliminate these thermal measures in order to simplify system's design, improve efficiency, reduce development and launch costs, and improve reliability. These requirements can only be met through the development of electronic parts that are designed for proper and efficient operation under extreme temperature conditions. Silicon-on-insulator (SOI) based devices are finding more use in harsh environments due to the benefits that their inherent design offers in terms of reduced leakage currents, less power consumption, faster switching speeds, good radiation tolerance, and extreme temperature operability. Little is known, however, about their performance at cryogenic temperatures and under wide thermal swings. The objective of this work was to evaluate the performance of a new commercial-off-the-shelf (COTS) SOI parts over an extended temperature range and to determine the effects of thermal cycling on their performance. The results will establish a baseline on the suitability of such devices for use in space exploration missions under extreme temperatures, and will aid mission planners and circuit designers in the proper selection of electronic parts and circuits. The electronic part investigated in this work comprised of a CHT-NMOS80 high temperature N-channel MOSFET (metal-oxide semiconductor field-effect transistor) device that was manufactured by CISSOID. This high voltage, medium-power transistor is fabricated using SOI processes and is designed for extreme wide temperature applications such as geothermal well logging, aerospace and avionics, and automotive industry. It has a high DC current capability and is specified for operation in the temperature range of -55 C to +225 C

Policy analysis of the budget used in training program for reducing lower back pain among heavy equipment operators in the construction industry: System dynamics approach

NASA Astrophysics Data System (ADS)

Vitharana, V. H. P.; Chinda, T.

2018-04-01

Lower back pain (LBP), prevalence is high among the heavy equipment operators leading to high compensation cost in the construction industry. It is found that proper training program assists in reducing chances of having LBP. This study, therefore aims to examine different safety related budget available to support LBP related training program for different age group workers, utilizing system dynamics modeling approach. The simulation results show that at least 2.5% of the total budget must be allocated in the safety and health budget to reduce the chances of having LBP cases.

Development of tapered silver-halide fiber tips for a scanning near-field microscope operating in the middle infrared

NASA Astrophysics Data System (ADS)

Platkov, Max; Tsun, Alexander; Nagli, Lev; Katzir, Abraham

2006-12-01

We have constructed a scanning near-field infrared microscope (SNIM) which was based on a AgClBr fiber probe whose end was etched to form an aperture of a subwavelength diameter. A detailed study of the mechanical properties of a vibrating AgClBr probe was required for proper operation of the SNIM system. We have demonstrated that the system can be used for imaging and for topographic mapping of samples with a subwavelength resolution in the middle infrared. Such a SNIM will be a powerful tool for the study of microelectronic components or subcellular structures in biological cells.

Novel telementoring system for robot-assisted radical prostatectomy: impact on the learning curve.

PubMed

Hinata, Nobuyuki; Miyake, Hideaki; Kurahashi, Toshifumi; Ando, Makoto; Furukawa, Junya; Ishimura, Takeshi; Tanaka, Kazushi; Fujisawa, Masato

2014-05-01

To develop a Web-based audiovisual telementoring system for robot-assisted radical prostatectomy (RARP) and to assess the utility of this system. A telementoring system for RARP, consisting of a 3-dimensional high-definition view of the operating field, overview of the operating room, annotation function, and 2-channel audio feed with bidirectional connectivity between 2 institutions, was developed. The outcome of RARP performed for the initial 30 patients by 2 surgeons with telementoring was compared with that for 2 surgeons who received direct mentoring. This system was shown to function properly with an acceptable latency. There were no significant differences in several parameters reflecting surgical outcomes, including the operating time, complication rate, early continence status, and positive margin rate between the telementoring and direct mentoring groups. These findings suggest the usefulness of the telementoring system for promoting the spread of precise surgical techniques associated with RARP. To our knowledge, this is the first report concerning telementoring for robot-assisted surgery. Copyright © 2014 Elsevier Inc. All rights reserved.

Residual gas analysis for long-pulse, advanced tokamak operation.

PubMed

Klepper, C C; Hillis, D L; Bucalossi, J; Douai, D; Oddon, P; Vartanian, S; Colas, L; Manenc, L; Pégourié, B

2010-10-01

A shielded residual gas analyzer (RGA) system on Tore Supra can function during plasma operation and is set up to monitor the composition of the neutral gas in one of the pumping ducts of the toroidal pumped limited. This "diagnostic RGA" has been used in long-pulse (up to 6 min) discharges for continuous monitoring of up to 15 masses simultaneously. Comparison of the RGA-measured evolution of the H(2)/D(2) isotopic ratio in the exhaust gas to that measured by an energetic neutral particle analyzer in the plasma core provides a way to monitor the evolution of particle balance. RGA monitoring of corrective H(2) injection to maintain proper minority heating is providing a database for improved ion cyclotron resonance heating, potentially with RGA-base feedback control. In very long pulses (>4 min) absence of significant changes in the RGA-monitored, hydrocarbon particle pressures is an indication of proper operation of the actively cooled, carbon-based plasma facing components. Also H(2) could increase due to thermodesorption of overheated plasma facing components.

Development and manufacture of visor for helmet-mounted display

NASA Astrophysics Data System (ADS)

Krevor, David H.; McNelly, Gregg; Skubon, John; Speirs, Robert

2004-01-01

The manufacturing design and process development for the Visor for the JHMCS (Joint Helmet Mounted Cueing System) are discussed. The JHMCS system is a Helmet Mounted Display (HMD) system currently flying on the F-15, F-16 and F/A-18 aircraft. The Visor manufacturing processes are essential to both system performance and economy. The Visor functions both as the system optical combiner and personal protective equipment for the pilot. The Visor material is optical polycarbonate. For a military HMD system, the mechanical and environmental properties of the Visor are as necessary as the optical properties. The visor must meet stringent dimensional requirements to assure adequate system optical performance. Injection molding can provide dimensional fidelity to the requirements, if done properly. Concurrent design of the visor and the tool (i.e., the injection mold) is essential. The concurrent design necessarily considers manufacturing operations and the use environment of the Visor. Computer modeling of the molding process is a necessary input to the mold design. With proper attention to product design and tool development, it is possible to improve upon published standard dimensional tolerances for molded polycarbonate articles.

Vision Test in Seconds

NASA Technical Reports Server (NTRS)

1976-01-01

Acuity Systems, Inc. developed an electro-optical instrument under a grant from NASA to measure the visual performance of pilots. Transferred from Ames Research Center, this instrument now allows you to have your eyes tested in seconds by relatively unskilled operators. The device automatically measures refractive error of eye and prints out proper prescription for glasses. The unit also detects cataracts and glaucoma.

Dynamic Paper Constructions for Easier Visualization of Molecular Symmetry

ERIC Educational Resources Information Center

Sein, Lawrence T., Jr.

2010-01-01

A system for construction of simple poster-board models is described. The models dynamically demonstrate the symmetry operations of proper rotation, improper rotation, reflection, and inversion for the chemically important point groups D[subscript 3h], D[subscript 4h], D[subscript 5h], D[subscript 6h], T[subscript d], and O[subscript h]. The…

77 FR 34064 - Notice of Lodging of the Consent Decree under the Clean Water Act

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-08

... Permit; (3) Arecibo violates its Small MS4 General Permit by discharging sewage and sewage sludge not...; and failing to properly operate and maintain its system; and (4) discharges untreated sewage from its... public has or may have come into contact with the sewage. The proposed Consent Decree addresses the...

30 CFR 90.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2010 CFR

2010-07-01

... designated by the District Manager. (b) The operator shall not open or tamper with the seal of any filter... properly complete the dust data card that is provided by the manufacturer for each filter cassette. The... include that person's certification number. Respirable dust samples with data cards not properly completed...

30 CFR 90.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2011 CFR

2011-07-01

... designated by the District Manager. (b) The operator shall not open or tamper with the seal of any filter... properly complete the dust data card that is provided by the manufacturer for each filter cassette. The... include that person's certification number. Respirable dust samples with data cards not properly completed...

30 CFR 71.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2010 CFR

2010-07-01

... designated by the District Manager. (b) The operator shall not open or tamper with the seal of any filter... properly complete the dust data card that is provided by the manufacturer for each filter cassette. The... include that person's certification number. Respirable dust samples with data cards not properly completed...

30 CFR 71.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2011 CFR

2011-07-01

... designated by the District Manager. (b) The operator shall not open or tamper with the seal of any filter... properly complete the dust data card that is provided by the manufacturer for each filter cassette. The... include that person's certification number. Respirable dust samples with data cards not properly completed...

Longitudinal train dynamics: an overview

NASA Astrophysics Data System (ADS)

Wu, Qing; Spiryagin, Maksym; Cole, Colin

2016-12-01

This paper discusses the evolution of longitudinal train dynamics (LTD) simulations, which covers numerical solvers, vehicle connection systems, air brake systems, wagon dumper systems and locomotives, resistance forces and gravitational components, vehicle in-train instabilities, and computing schemes. A number of potential research topics are suggested, such as modelling of friction, polymer, and transition characteristics for vehicle connection simulations, studies of wagon dumping operations, proper modelling of vehicle in-train instabilities, and computing schemes for LTD simulations. Evidence shows that LTD simulations have evolved with computing capabilities. Currently, advanced component models that directly describe the working principles of the operation of air brake systems, vehicle connection systems, and traction systems are available. Parallel computing is a good solution to combine and simulate all these advanced models. Parallel computing can also be used to conduct three-dimensional long train dynamics simulations.

Centaur Standard Shroud (CSS) cryogenic unlatch tests

NASA Technical Reports Server (NTRS)

1973-01-01

Cryogenic tanking and partial jettison (unlatch) tests were performed on a full scale Centaur vehicle and Centaur Standard Shroud (CSS) to develop and qualify the CSS insulation system, the CSS and Centaur ground-hold purge systems, and the Centaur hydrogen tank flight vent system. Operation of the shroud/Centaur pyrotechnic systems, seals, and the shroud jettison springs, hinges, and other separation systems was demonstrated by a partial jettison of the shroud into catch nets. The Centaur tanks were filled with liquid hydrogen and liquid nitrogen. Prelaunch operations were performed, and data taken to establish system performances. Results from the initial tests showed a higher than expected heat transfer rate to the Centaur hydrogen tank. In addition, the release mechanism for the forward seal between the Centaur and the CSS did not function properly, and the seal was torn during jettison of the shroud.

Cattle traceability system in Japan for bovine spongiform encephalopathy.

PubMed

Sugiura, Katsuaki; Onodera, Takashi

2008-01-01

To promote consumer confidence in the safety of beef and to ensure the proper implementation of eradication measures against bovine spongiform encephalopathy (BSE), the Cattle Traceability Law was approved by the Diet in June 2003 and a cattle traceability system has been in operation in Japan since December 2003. The system enables tracing the cohort and offspring animals of a BSE case within 24 h of its detection. The traceability database system also provides distributors, restaurants and consumers with information on the cattle from which the beef that they sell, serve and consume, originate.

Anaesthesia for children with bronchial asthma and respiratory infections.

PubMed

Rajesh, M C

2015-09-01

Asthma represents one of the most common chronic diseases in children with an increasing incidence reported worldwide. The key to successful anaesthetic outcome involves thorough pre-operative assessment and optimisation of the child's pulmonary status. Judicious application of proper anti-inflammatory and bronchodilatory regimes should be instituted as part of pre-operative preparation. Bronchospasm triggering agents should be carefully probed and meticulously avoided. A calm and properly sedated child at the time of induction is ideal, so also is extubation in a deep plane with an unobstructed airway. Wherever possible, regional anaesthesia should be employed. This will avoid airway manipulations, with additional benefit of excellent peri-operative analgesia. Agents with a potential for histamine release and techniques that can increase airway resistance should be diligently avoided. Emphasis must be given to proper post-operative care including respiratory monitoring, analgesia and breathing exercises.

Image-guided laparoscopic surgery in an open MRI operating theater.

PubMed

Tsutsumi, Norifumi; Tomikawa, Morimasa; Uemura, Munenori; Akahoshi, Tomohiko; Nagao, Yoshihiro; Konishi, Kozo; Ieiri, Satoshi; Hong, Jaesung; Maehara, Yoshihiko; Hashizume, Makoto

2013-06-01

The recent development of open magnetic resonance imaging (MRI) has provided an opportunity for the next stage of image-guided surgical and interventional procedures. The purpose of this study was to evaluate the feasibility of laparoscopic surgery under the pneumoperitoneum with the system of an open MRI operating theater. Five patients underwent laparoscopic surgery with a real-time augmented reality navigation system that we previously developed in a horizontal-type 0.4-T open MRI operating theater. All procedures were performed in an open MRI operating theater. During the operations, the laparoscopic monitor clearly showed the augmented reality models of the intraperitoneal structures, such as the common bile ducts and the urinary bladder, as well as the proper positions of the prosthesis. The navigation frame rate was 8 frames per min. The mean fiducial registration error was 6.88 ± 6.18 mm in navigated cases. We were able to use magnetic resonance-incompatible surgical instruments out of the 5-Gs restriction area, as well as conventional laparoscopic surgery, and we developed a real-time augmented reality navigation system using open MRI. Laparoscopic surgery with our real-time augmented reality navigation system in the open MRI operating theater is a feasible option.

The use of automation and robotic systems to establish and maintain lunar base operations

NASA Technical Reports Server (NTRS)

Petrosky, Lyman J.

1992-01-01

Robotic systems provide a means of performing many of the operations required to establish and maintain a lunar base. They form a synergistic system when properly used in concert with human activities. This paper discusses the various areas where robotics and automation may be used to enhance lunar base operations. Robots are particularly well suited for surface operations (exterior to the base habitat modules) because they can be designed to operate in the extreme temperatures and vacuum conditions of the Moon (or Mars). In this environment, the capabilities of semi-autonomous robots would surpass that of humans in all but the most complex tasks. Robotic surface operations include such activities as long range geological and mineralogical surveys with sample return, materials movement in and around the base, construction of radiation barriers around habitats, transfer of materials over large distances, and construction of outposts. Most of the above operations could be performed with minor modifications to a single basic robotic rover. Within the lunar base habitats there are a few areas where robotic operations would be preferable to human operations. Such areas include routine inspections for leakage in the habitat and its systems, underground transfer of materials between habitats, and replacement of consumables. In these and many other activities, robotic systems will greatly enhance lunar base operations. The robotic systems described in this paper are based on what is realistically achievable with relatively near term technology. A lunar base can be built and maintained if we are willing.

Data Management for Mars Exploration Rovers

NASA Technical Reports Server (NTRS)

Snyder, Joseph F.; Smyth, David E.

2004-01-01

Data Management for the Mars Exploration Rovers (MER) project is a comprehensive system addressing the needs of development, test, and operations phases of the mission. During development of flight software, including the science software, the data management system can be simulated using any POSIX file system. During testing, the on-board file system can be bit compared with files on the ground to verify proper behavior and end-to-end data flows. During mission operations, end-to-end accountability of data products is supported, from science observation concept to data products within the permanent ground repository. Automated and human-in-the-loop ground tools allow decisions regarding retransmitting, re-prioritizing, and deleting data products to be made using higher level information than is available to a protocol-stack approach such as the CCSDS File Delivery Protocol (CFDP).

Biofiltration: Fundamentals, design and operations principles and applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swanson, W.J.; Loehr, R.C.

1997-06-01

Biofiltration is a biological air pollution control technology for volatile organic compounds (VOCs). This paper summarizes the fundamentals, design and operation, and application of the process. Biofiltration has been demonstrated to be an effective technology for VOCs from many industries. Large and full-scale systems are in use in Europe and the US. With proper design and operation, VOC removal efficiencies of 95--99% have been achieved. Important parameters for design and performance are empty-bed contact time, gas surface loading, mass loading, elimination capacity, and removal efficiency. Key design and operation factors include chemical and media properties, moisture, pH, temperature, nutrient availability,more » gas pretreatment, and variations in loading.« less

Instrumentation, control, and automation for submerged anaerobic membrane bioreactors.

PubMed

Robles, Ángel; Durán, Freddy; Ruano, María Victoria; Ribes, Josep; Rosado, Alfredo; Seco, Aurora; Ferrer, José

2015-01-01

A submerged anaerobic membrane bioreactor (AnMBR) demonstration plant with two commercial hollow-fibre ultrafiltration systems (PURON®, Koch Membrane Systems, PUR-PSH31) was designed and operated for urban wastewater treatment. An instrumentation, control, and automation (ICA) system was designed and implemented for proper process performance. Several single-input-single-output (SISO) feedback control loops based on conventional on-off and PID algorithms were implemented to control the following operating variables: flow-rates (influent, permeate, sludge recycling and wasting, and recycled biogas through both reactor and membrane tanks), sludge wasting volume, temperature, transmembrane pressure, and gas sparging. The proposed ICA for AnMBRs for urban wastewater treatment enables the optimization of this new technology to be achieved with a high level of process robustness towards disturbances.

The Integrated Waste Tracking System - A Flexible Waste Management Tool

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, Robert Stephen

2001-02-01

The US Department of Energy (DOE) Idaho National Engineering and Environmental Laboratory (INEEL) has fully embraced a flexible, computer-based tool to help increase waste management efficiency and integrate multiple operational functions from waste generation through waste disposition while reducing cost. The Integrated Waste Tracking System (IWTS)provides comprehensive information management for containerized waste during generation,storage, treatment, transport, and disposal. The IWTS provides all information necessary for facilities to properly manage and demonstrate regulatory compliance. As a platformindependent, client-server and Web-based inventory and compliance system, the IWTS has proven to be a successful tracking, characterization, compliance, and reporting tool that meets themore » needs of both operations and management while providing a high level of management flexibility.« less

Test Rig for Evaluating Active Turbine Blade Tip Clearance Control Concepts

NASA Technical Reports Server (NTRS)

Lattime, Scott B.; Steinetz, Bruce M.; Robbie, Malcolm G.

2003-01-01

Improved blade tip sealing in the high pressure compressor and high pressure turbine can provide dramatic improvements in specific fuel consumption, time-on-wing, compressor stall margin and engine efficiency as well as increased payload and mission range capabilities of both military and commercial gas turbine engines. The preliminary design of a mechanically actuated active clearance control (ACC) system for turbine blade tip clearance management is presented along with the design of a bench top test rig in which the system is to be evaluated. The ACC system utilizes mechanically actuated seal carrier segments and clearance measurement feedback to provide fast and precise active clearance control throughout engine operation. The purpose of this active clearance control system is to improve upon current case cooling methods. These systems have relatively slow response and do not use clearance measurement, thereby forcing cold build clearances to set the minimum clearances at extreme operating conditions (e.g., takeoff, re-burst) and not allowing cruise clearances to be minimized due to the possibility of throttle transients (e.g., step change in altitude). The active turbine blade tip clearance control system design presented herein will be evaluated to ensure that proper response and positional accuracy is achievable under simulated high-pressure turbine conditions. The test rig will simulate proper seal carrier pressure and temperature loading as well as the magnitudes and rates of blade tip clearance changes of an actual gas turbine engine. The results of these evaluations will be presented in future works.

Multi-arm multilateral haptics-based immersive tele-robotic system (HITS) for improvised explosive device disposal

NASA Astrophysics Data System (ADS)

Erickson, David; Lacheray, Hervé; Lai, Gilbert; Haddadi, Amir

2014-06-01

This paper presents the latest advancements of the Haptics-based Immersive Tele-robotic System (HITS) project, a next generation Improvised Explosive Device (IED) disposal (IEDD) robotic interface containing an immersive telepresence environment for a remotely-controlled three-articulated-robotic-arm system. While the haptic feedback enhances the operator's perception of the remote environment, a third teleoperated dexterous arm, equipped with multiple vision sensors and cameras, provides stereo vision with proper visual cues, and a 3D photo-realistic model of the potential IED. This decentralized system combines various capabilities including stable and scaled motion, singularity avoidance, cross-coupled hybrid control, active collision detection and avoidance, compliance control and constrained motion to provide a safe and intuitive control environment for the operators. Experimental results and validation of the current system are presented through various essential IEDD tasks. This project demonstrates that a two-armed anthropomorphic Explosive Ordnance Disposal (EOD) robot interface can achieve complex neutralization techniques against realistic IEDs without the operator approaching at any time.

Classification of Aircraft Maneuvers for Fault Detection

NASA Technical Reports Server (NTRS)

Oza, Nikunj C.; Tumer, Irem Y.; Tumer, Kagan; Huff, Edward M.; Clancy, Daniel (Technical Monitor)

2002-01-01

Automated fault detection is an increasingly important problem in aircraft maintenance and operation. Standard methods of fault detection assume the availability of either data produced during all possible faulty operation modes or a clearly-defined means to determine whether the data is a reasonable match to known examples of proper operation. In our domain of fault detection in aircraft, the first assumption is unreasonable and the second is difficult to determine. We envision a system for online fault detection in aircraft, one part of which is a classifier that predicts the maneuver being performed by the aircraft as a function of vibration data and other available data. We explain where this subsystem fits into our envisioned fault detection system as well its experiments showing the promise of this classification subsystem.

Choosing order of operations to accelerate strip structure analysis in parameter range

NASA Astrophysics Data System (ADS)

Kuksenko, S. P.; Akhunov, R. R.; Gazizov, T. R.

2018-05-01

The paper considers the issue of using iteration methods in solving the sequence of linear algebraic systems obtained in quasistatic analysis of strip structures with the method of moments. Using the analysis of 4 strip structures, the authors have proved that additional acceleration (up to 2.21 times) of the iterative process can be obtained during the process of solving linear systems repeatedly by means of choosing a proper order of operations and a preconditioner. The obtained results can be used to accelerate the process of computer-aided design of various strip structures. The choice of the order of operations to accelerate the process is quite simple, universal and could be used not only for strip structure analysis but also for a wide range of computational problems.

30 CFR 70.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2010 CFR

2010-07-01

... operator shall not open or tamper with the seal of any filter cassette or alter the weight of any filter... accordance with § 70.202 (Certified person; sampling) shall properly complete the dust data card that is.... Respirable dust samples with data cards not properly completed will be voided by MSHA. (d) All respirable...

30 CFR 70.209 - Respirable dust samples; transmission by operator.

Code of Federal Regulations, 2011 CFR

2011-07-01

... operator shall not open or tamper with the seal of any filter cassette or alter the weight of any filter... accordance with § 70.202 (Certified person; sampling) shall properly complete the dust data card that is.... Respirable dust samples with data cards not properly completed will be voided by MSHA. (d) All respirable...

Classification of Aircraft Maneuvers for Fault Detection

NASA Technical Reports Server (NTRS)

Oza, Nikunj; Tumer, Irem Y.; Tumer, Kagan; Huff, Edward M.; Koga, Dennis (Technical Monitor)

2002-01-01

Automated fault detection is an increasingly important problem in aircraft maintenance and operation. Standard methods of fault detection assume the availability of either data produced during all possible faulty operation modes or a clearly-defined means to determine whether the data provide a reasonable match to known examples of proper operation. In the domain of fault detection in aircraft, the first assumption is unreasonable and the second is difficult to determine. We envision a system for online fault detection in aircraft, one part of which is a classifier that predicts the maneuver being performed by the aircraft as a function of vibration data and other available data. To develop such a system, we use flight data collected under a controlled test environment, subject to many sources of variability. We explain where our classifier fits into the envisioned fault detection system as well as experiments showing the promise of this classification subsystem.

Functional Risk Modeling for Lunar Surface Systems

NASA Technical Reports Server (NTRS)

Thomson, Fraser; Mathias, Donovan; Go, Susie; Nejad, Hamed

2010-01-01

We introduce an approach to risk modeling that we call functional modeling , which we have developed to estimate the capabilities of a lunar base. The functional model tracks the availability of functions provided by systems, in addition to the operational state of those systems constituent strings. By tracking functions, we are able to identify cases where identical functions are provided by elements (rovers, habitats, etc.) that are connected together on the lunar surface. We credit functional diversity in those cases, and in doing so compute more realistic estimates of operational mode availabilities. The functional modeling approach yields more realistic estimates of the availability of the various operational modes provided to astronauts by the ensemble of surface elements included in a lunar base architecture. By tracking functional availability the effects of diverse backup, which often exists when two or more independent elements are connected together, is properly accounted for.

Use or abuse of computers in the workplace.

PubMed

Gregg, Robert E

2007-01-01

Is your computer system about to become your next liability by the misuse of computers in the workplace? "E-discovery" reveals evidence of harassment, discrimination, defamation, and more. Yet employees also sue when the employer improperly intercepts electronic messages the employees claim were "private." Employers need to be aware of the issues of use, misuse, and rights to properly monitor and control the electronic system. Learn the current issues, legal trends, and practical pointers for your electronic operations.

Optical spectral singularities as threshold resonances

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mostafazadeh, Ali

2011-04-15

Spectral singularities are among generic mathematical features of complex scattering potentials. Physically they correspond to scattering states that behave like zero-width resonances. For a simple optical system, we show that a spectral singularity appears whenever the gain coefficient coincides with its threshold value and other parameters of the system are selected properly. We explore a concrete realization of spectral singularities for a typical semiconductor gain medium and propose a method of constructing a tunable laser that operates at threshold gain.

Limited Connected Speech Experiment.

DTIC Science & Technology

1983-03-01

male and twenty-five female speakers. This report describesT1 - s -"" real-time laboratory CSR system, the data base and training software de- O R M’ a...sounding word( s ). The end point detection class contains those errors in which the CSR system did not properly detect the beginning or end of the phrase...processing continues following end-of-file on the initialization ile. - s Operate in silent, rather than verbose, mode. Normally, each CSR com- mand

Calibration and operation of the Faint Object Spectrograph

NASA Technical Reports Server (NTRS)

Harms, R.; Beaver, E.; Burbidge, E.; Hier, R.; Allen, R.; Angel, R.; Bartko, F.; Bohlin, R.; Ford, H.; Davidson, A.

1984-01-01

The design and basic performance characteristics of the Faint Object Spectrograph (FOS), one of five instruments built for use on the Space Telescope observatory, is summarized briefly. The results of the recently completed instrument-level calibration are presented with special emphasis on issues affecting plans for FOS astronomical observations. Examples include such fundamental characteristics as: limiting magnitudes (system sensitivity and noise figures), spectral coverage and resolution, scattered light properties, and instrumental polarization and modulation efficiencies. Also gated toward intended users, a rather detailed description of FOS operating modes is given. The discussion begins with the difficulties anticipated during target acquisition and their hoped-for resolution. Both the 'normal' spectroscopic operating modes of the FOS and its 'exotic' features (e.g. spectropolarimetric, time-tagged, and time-resolved modes) are presented. The paper concludes with an overview of the activities to assure proper alignment and operation of the FOS within the entire Space Telescope system (orbital and ground-based).

[Robotics in general surgery: personal experience, critical analysis and prospectives].

PubMed

Fracastoro, Gerolamo; Borzellino, Giuseppe; Castelli, Annalisa; Fiorini, Paolo

2005-01-01

Today mini invasive surgery has the chance to be enhanced with sophisticated informative systems (Computer Assisted Surgery, CAS) like robotics, tele-mentoring and tele-presence. ZEUS and da Vinci, present in more than 120 Centres in the world, have been used in many fields of surgery and have been tested in some general surgical procedures. Since the end of 2003, we have performed 70 experimental procedures and 24 operations of general surgery with ZEUS robotic system, after having properly trained 3 surgeons and the operating room staff. Apart from the robot set-up, the mean operative time of the robotic operations was similar to the laparoscopic ones; no complications due to robotic technique occurred. The Authors report benefits and disadvantages related to robots' utilization, problems still to be solved and the possibility to make use of them with tele-surgery, training and virtual surgery.

Contingency Management Requirements Document: Preliminary Version. Revision F

NASA Technical Reports Server (NTRS)

2005-01-01

This is the High Altitude, Long Endurance (HALE) Remotely Operated Aircraft (ROA) Contingency Management (CM) Functional Requirements document. This document applies to HALE ROA operating within the National Airspace System (NAS) limited at this time to enroute operations above 43,000 feet (defined as Step 1 of the Access 5 project, sponsored by the National Aeronautics and Space Administration). A contingency is an unforeseen event requiring a response. The unforeseen event may be an emergency, an incident, a deviation, or an observation. Contingency Management (CM) is the process of evaluating the event, deciding on the proper course of action (a plan), and successfully executing the plan.

Experimental prototype of an electric elevator

NASA Astrophysics Data System (ADS)

Gaiceanu, M.; Epure, S.; Ciuta, S.

2016-08-01

The main objective is to achieve an elevator prototype powered by a three-phase voltage system via a bidirectional static power converter ac-ac with regenerating capability. In order to diminish the power size of the electric motor up to 1/3 of rated power, the elevator contains two carriages of the same weight, one serving as the payload, and the other as counterweight. Before proper operation of the static power converter, the capacitor must be charged at rated voltage via a precharge circuit. At the moment of stabilizing the DC voltage at nominal value, the AC-AC power converter can operates in the proper limits. The functions of the control structure are: the load control task, speed and torque controls. System includes transducers for current measuring, voltage sensors and encoder. As reserve power sources the hybrid battery-photovoltaic panels are used. The control voltage is modulated by implementing four types of pulse width modulations: sinusoidal, with reduced commutation, third order harmonic insertion, and the space vector modulation. Therefore, the prototype could operates with an increased efficiency, in spite of the existing ones. The experimental results confirm the well design of the chosen solution. The control solution assures bidirectional power flow control, precharge control, and load control and it is implemented on a digital signal processor. The elevator capacity is between 300-450 kg, and it is driven by using a 1.5 kW three-phase asynchronous machine.

Design, Qualification, and On Orbit Performance of the CALIPSO Aerosol Lidar Transmitter

NASA Technical Reports Server (NTRS)

Hovis, Floyd E.; Witt, Greg; Sullivan, Edward T.; Le, Khoa; Weimer, Carl; Applegate, Jeff; Luck, William S., Jr.; Verhapen, Ron; Cisewski, Michael S.

2007-01-01

The laser transmitter for the CALIPSO aerosol lidar mission has been operating on orbit as planned since June 2006. This document discusses the optical and laser system design and qualification process that led to this success. Space-qualifiable laser design guidelines included the use of mature laser technologies, the use of alignment sensitive resonator designs, the development and practice of stringent contamination control procedures, the operation of all optical components at appropriately derated levels, and the proper budgeting for the space-qualification of the electronics and software.

Wheat stress indicator model, Crop Condition Assessment Division (CCAD) data base interface driver, user's manual

NASA Technical Reports Server (NTRS)

Hansen, R. F. (Principal Investigator)

1981-01-01

The use of the wheat stress indicator model CCAD data base interface driver is described. The purpose of this system is to interface the wheat stress indicator model with the CCAD operational data base. The interface driver routine decides what meteorological stations should be processed and calls the proper subroutines to process the stations.

IT Governance and the Public Sector: A Survey of Perceptions, Attitudes, and Knowledge of Federal Public Sector IT Employees

ERIC Educational Resources Information Center

Martin, David P.

2013-01-01

IT governance has become an important topic as both public and private organizations struggle to meet the challenge of aligning complex IT systems with operational needs. Without effective IT governance, organizations fail to gain strategic benefits that come by the proper strategic alignment of IT resources with the larger organizational mission.…

77 FR 1934 - Information Collections Being Reviewed by the Federal Communications Commission

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-12

... technology; and (e) ways to further reduce the information collection burden on small business concerns with... shall be retained for a period of two years. 47 CFR 78.69 requires each licensee of a CARS station shall... proper operation of the tower lights was made, if an automatic alarm system is not employed. (3) In the...

Development of bioengineering system for stem cell proliferation

NASA Astrophysics Data System (ADS)

Park, H. S.; Shah, R.; Shah, C.

2016-08-01

From last decades, intensive research in the field of stem cells proliferation had been promoted due to the unique property of stem cells to self-renew themselves into multiples and has potential to replicate into an organ or tissues and so it's highly demanding though challenging. Bioreactor, a mechanical device, works as a womb for stem cell proliferation by providing nutritious environment for the proper growth of stem cells. Various factors affecting stem cells growth are the bioreactor mechanism, feeding of continuous nutrients, healthy environment, etc., but it always remains a challenge for controlling biological parameters. The present paper unveils the design of mechanical device commonly known as bioreactor in tissues engineering and biotech field, use for proliferation of stem cells and imparts the proper growing condition for stem cells. This high functional bioreactor provides automation mixing of cell culture and stem cells. This design operates in conjunction with mechanism of reciprocating motion. Compare to commercial bioreactors, this proposed design is more convenient, easy to operate and less maintenance is required as bioreactor culture bag is made of polyethylene which is single use purpose. Development of this bioengineering system will be beneficial for better growth and expansion of stem cell

Performance of High Temperature Operational Amplifier, Type LM2904WH, under Extreme Temperatures

NASA Technical Reports Server (NTRS)

Patterson, Richard; Hammoud, Ahmad; Elbuluk, Malik

2008-01-01

Operation of electronic parts and circuits under extreme temperatures is anticipated in NASA space exploration missions as well as terrestrial applications. Exposure of electronics to extreme temperatures and wide-range thermal swings greatly affects their performance via induced changes in the semiconductor material properties, packaging and interconnects, or due to incompatibility issues between interfaces that result from thermal expansion/contraction mismatch. Electronics that are designed to withstand operation and perform efficiently in extreme temperatures would mitigate risks for failure due to thermal stresses and, therefore, improve system reliability. In addition, they contribute to reducing system size and weight, simplifying its design, and reducing development cost through the elimination of otherwise required thermal control elements for proper ambient operation. A large DC voltage gain (100 dB) operational amplifier with a maximum junction temperature of 150 C was recently introduced by STMicroelectronics [1]. This LM2904WH chip comes in a plastic package and is designed specifically for automotive and industrial control systems. It operates from a single power supply over a wide range of voltages, and it consists of two independent, high gain, internally frequency compensated operational amplifiers. Table I shows some of the device manufacturer s specifications.

Integration of the TDWR and LLWAS wind shear detection system

NASA Technical Reports Server (NTRS)

Cornman, Larry

1991-01-01

Operational demonstrations of a prototype TDWR/LLWAS (Terminal Doppler Weather Radar/Low Level Wind shear Alarm System) integrated wind shear detection system were conducted. The integration of wind shear detection systems is needed to provide end-users with a single, consensus source of information. A properly implemented integrated system provides wind shear warnings of a higher quality than stand-alone LLWAS or TDWR systems. The algorithmic concept used to generate the TDWR/LLWAS integrated products and several case studies are discussed, indicating the viability and potential of integrated wind shear detection systems. Implications for integrating ground and airborne wind shear detection systems are briefly examined.

Expanding AirSTAR Capability for Flight Research in an Existing Avionics Design

NASA Technical Reports Server (NTRS)

Laughter, Sean A.

2012-01-01

The NASA Airborne Subscale Transport Aircraft Research (AirSTAR) project is an Unmanned Aerial Systems (UAS) test bed for experimental flight control laws and vehicle dynamics research. During its development, the test bed has gone through a number of system permutations, each meant to add functionality to the concept of operations of the system. This enabled the build-up of not only the system itself, but also the support infrastructure and processes necessary to support flight operations. These permutations were grouped into project phases and the move from Phase-III to Phase-IV was marked by a significant increase in research capability and necessary safety systems due to the integration of an Internal Pilot into the control system chain already established for the External Pilot. The major system changes in Phase-IV operations necessitated a new safety and failsafe system to properly integrate both the Internal and External Pilots and to meet acceptable project safety margins. This work involved retrofitting an existing data system into the evolved concept of operations. Moving from the first Phase-IV aircraft to the dynamically scaled aircraft further involved restructuring the system to better guard against electromagnetic interference (EMI), and the entire avionics wiring harness was redesigned in order to facilitate better maintenance and access to onboard electronics. This retrofit and harness re-design will be explored and how it integrates with the evolved Phase-IV operations.

Designing a SCADA system simulator for fast breeder reactor

NASA Astrophysics Data System (ADS)

Nugraha, E.; Abdullah, A. G.; Hakim, D. L.

2016-04-01

SCADA (Supervisory Control and Data Acquisition) system simulator is a Human Machine Interface-based software that is able to visualize the process of a plant. This study describes the results of the process of designing a SCADA system simulator that aims to facilitate the operator in monitoring, controlling, handling the alarm, accessing historical data and historical trend in Nuclear Power Plant (NPP) type Fast Breeder Reactor (FBR). This research used simulation to simulate NPP type FBR Kalpakkam in India. This simulator was developed using Wonderware Intouch software 10 and is equipped with main menu, plant overview, area graphics, control display, set point display, alarm system, real-time trending, historical trending and security system. This simulator can properly simulate the principle of energy flow and energy conversion process on NPP type FBR. This SCADA system simulator can be used as training media for NPP type FBR prospective operators.

A system of nonlinear set valued variational inclusions.

PubMed

Tang, Yong-Kun; Chang, Shih-Sen; Salahuddin, Salahuddin

2014-01-01

In this paper, we studied the existence theorems and techniques for finding the solutions of a system of nonlinear set valued variational inclusions in Hilbert spaces. To overcome the difficulties, due to the presence of a proper convex lower semicontinuous function ϕ and a mapping g which appeared in the considered problems, we have used the resolvent operator technique to suggest an iterative algorithm to compute approximate solutions of the system of nonlinear set valued variational inclusions. The convergence of the iterative sequences generated by algorithm is also proved. 49J40; 47H06.

Artificial intelligence, neural network, and Internet tool integration in a pathology workstation to improve information access

NASA Astrophysics Data System (ADS)

Sargis, J. C.; Gray, W. A.

1999-03-01

The APWS allows user friendly access to several legacy systems which would normally each demand domain expertise for proper utilization. The generalized model, including objects, classes, strategies and patterns is presented. The core components of the APWS are the Microsoft Windows 95 Operating System, Oracle, Oracle Power Objects, Artificial Intelligence tools, a medical hyperlibrary and a web site. The paper includes a discussion of how could be automated by taking advantage of the expert system, object oriented programming and intelligent relational database tools within the APWS.

Data Management System (DMS) Evolution Analysis

NASA Technical Reports Server (NTRS)

Douglas, Katherine

1990-01-01

The all encompassing goal for the Data Management System (DMS) Evolution Analysis task is to develop an advocacy for ensuring that growth and technology insertion issues are properly and adequately addressed during DMS requirements specification, design, and development. The most efficient methods of addressing those issues are via planned and graceful evolution, technology transparency, and system growth margins. It is necessary that provisions, such as those previously mentioned, are made to accommodate advanced missions requirements (e.g., Human Space Exploration Programs) in addition to evolving Space Station Freedom operations and user requirements .

Voice technology and BBN

NASA Technical Reports Server (NTRS)

Wolf, Jared J.

1977-01-01

The following research was discussed: (1) speech signal processing; (2) automatic speech recognition; (3) continuous speech understanding; (4) speaker recognition; (5) speech compression; (6) subjective and objective evaluation of speech communication system; (7) measurement of the intelligibility and quality of speech when degraded by noise or other masking stimuli; (8) speech synthesis; (9) instructional aids for second-language learning and for training of the deaf; and (10) investigation of speech correlates of psychological stress. Experimental psychology, control systems, and human factors engineering, which are often relevant to the proper design and operation of speech systems are described.

Flight control system design factors for applying automated testing techniques

NASA Technical Reports Server (NTRS)

Sitz, Joel R.; Vernon, Todd H.

1990-01-01

The principal design features and operational experiences of the X-29 forward-swept-wing aircraft and F-18 high alpha research vehicle (HARV) automated test systems are discussed. It is noted that operational experiences in developing and using these automated testing techniques have highlighted the need for incorporating target system features to improve testability. Improved target system testability can be accomplished with the addition of nonreal-time and real-time features. Online access to target system implementation details, unobtrusive real-time access to internal user-selectable variables, and proper software instrumentation are all desirable features of the target system. Also, test system and target system design issues must be addressed during the early stages of the target system development. Processing speeds of up to 20 million instructions/s and the development of high-bandwidth reflective memory systems have improved the ability to integrate the target system and test system for the application of automated testing techniques. It is concluded that new methods of designing testability into the target systems are required.

Concept and design engineering: endourology operating room.

PubMed

Sabnis, Ravindra; Ganesamoni, Raguram; Mishra, Shashikant; Sinha, Lokesh; Desai, Mahesh R

2013-03-01

A dedicated operating room with fluoroscopic imaging capability and adequate data connectivity is important to the success of any endourology program. Proper understanding of the recent developments in technology in relation to operating room is necessary before planning an endourology operating room. An endourology operating room is a fluorocompatible operating room with enough space to accommodate equipment like multiple flat monitors to display video, C-arm with its monitor, ultrasonography machine, laser machine, intracorporeal lithotripsy unit, irrigation pumps and two large trolleys with instruments. This operating room is integrated with devices to continuously record and archive data from endovision and surface cameras, ultrasound and fluoroscopy. Moreover, advances made in data relay systems have created seamless two-way communication between the operating room and electronic medical records, radiological picture archiving and communication system, classroom, auditorium and literally anywhere in the world. A dedicated endourology operating room is required for any hospital, which has a significant amount of endourology procedures. A custom-made integrated endourology operating room will facilitate endourology procedures, smoothen the workflow in operating room and improve patient outcomes. Meticulous planning and involving experts in the field are critical for the success of the project.

Con Edison power failure of July 13 and 14, 1977. Final staff report

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1978-06-01

On July 13, 1977 the entire electric load of the Con Edison system was lost, plunging New York City and Westchester County into darkness. The collapse resulted from a combination of natural events, equipment malfunctions, questionable system-design features, and operating errors. An attempt is made in this report to answer the following: what were the specific causes of the failure; if equipment malfunctions and operator errors contributed, could they have been prevented; to what extent was Con Edison prepared to handle such an emergency; and did Con Edison plan prudently reserve generation, for reserve transmission capability, for automatic equipment tomore » protect its system, and for proper operator response to a critical situation. Following the introductory and summary section, additional sections include: the Consolidated Edison system; prevention of bulk power-supply interruptions; the sequence of failure and restoration; analysis of the July 1977 power failure; restoration sequence and equipment damage assessment; and other investigations of the blackout. (MCW)« less

Identifying and Modeling Dynamic Preference Evolution in Multipurpose Water Resources Systems

NASA Astrophysics Data System (ADS)

Mason, E.; Giuliani, M.; Castelletti, A.; Amigoni, F.

2018-04-01

Multipurpose water systems are usually operated on a tradeoff of conflicting operating objectives. Under steady state climatic and socioeconomic conditions, such tradeoff is supposed to represent a fair and/or efficient preference. Extreme variability in external forcing might affect water operators' risk aversion and force a change in her/his preference. Properly accounting for these shifts is key to any rigorous retrospective assessment of the operator's behaviors, and to build descriptive models for projecting the future system evolution. In this study, we explore how the selection of different preferences is linked to variations in the external forcing. We argue that preference selection evolves according to recent, extreme variations in system performance: underperforming in one of the objectives pushes the preference toward the harmed objective. To test this assumption, we developed a rational procedure to simulate the operator's preference selection. We map this selection onto a multilateral negotiation, where multiple virtual agents independently optimize different objectives. The agents periodically negotiate a compromise policy for the operation of the system. Agents' attitudes in each negotiation step are determined by the recent system performance measured by the specific objective they maximize. We then propose a numerical model of preference dynamics that implements a concept from cognitive psychology, the availability bias. We test our modeling framework on a synthetic lake operated for flood control and water supply. Results show that our model successfully captures the operator's preference selection and dynamic evolution driven by extreme wet and dry situations.

Studying Si/SiGe disordered alloys within effective mass theory

NASA Astrophysics Data System (ADS)

Gamble, John; Montaño, Inès; Carroll, Malcolm S.; Muller, Richard P.

Si/SiGe is an attractive material system for electrostatically-defined quantum dot qubits due to its high-quality crystalline quantum well interface. Modeling the properties of single-electron quantum dots in this system is complicated by the presence of alloy disorder, which typically requires atomistic techniques in order to treat properly. Here, we use the NEMO-3D empirical tight binding code to calibrate a multi-valley effective mass theory (MVEMT) to properly handle alloy disorder. The resulting MVEMT simulations give good insight into the essential physics of alloy disorder, while being extremely computationally efficient and well-suited to determining statistical properties. Sandia is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the US Department of Energy's National Nuclear Security Administration under Contract No. DE-AC04-94AL85000.

Turbine and superheater bypass evaluation. Final report. [Faster startup in cycling operation and less erosion with steam bypass systems, including bypass design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosard, D.D.; Steltz, W.G.

1986-10-01

Properly sized turbine and boiler bypass systems permit two-shift cycling operation of units, shorten start-up time, and reduce life expenditures of plant components. With bypasses installed, faster startups can reduce fuel costs by $100,000 per year for a typical 500-MW fossil-fired unit. This report discusses the technical characteristics of existing bypass systems and provides guidelines for sizing bypass systems to achieve economical and reliable two-shift operation. The collection and analysis of startup data from several generating units were used in conjunction with computer simulations to illustrate the effects of adding various arrangements and sizes of steam bypass systems. The report,more » which indicates that shutdown procedures have significant impact on subsequent startup and loading time, describes operating practices to optimize the effectiveness of bypass systems. To determine the effectiveness of large turbine bypass systems of less than 100% capacity in preventing boiler trips following load rejection, transient field data were compared to a load rejection simulation using the modular modeling system (MMS). The MMS was then used to predict system response to other levels of load rejection. 7 refs., 87 figs., 8 tabs.« less

Alarm rationalization: practical experience rationalizing alarm configuration for an accelerator subsystem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kasemir, Kay; Hartman, Steven M

2009-01-01

A new alarm system toolkit has been implemented at SNS. The toolkit handles the Central Control Room (CCR) 'annunciator', or audio alarms. For the new alarm system to be effective, the alarms must be meaningful and properly configured. Along with the implementation of the new alarm toolkit, a thorough documentation and rationalization of the alarm configuration is taking place. Requirements and maintenance of a robust alarm configuration have been gathered from system and operations experts. In this paper we present our practical experience with the vacuum system alarm handling configuration of the alarm toolkit.

Power quality considerations for nuclear spectroscopy applications: Grounding

NASA Astrophysics Data System (ADS)

García-Hernández, J. M.; Ramírez-Jiménez, F. J.; Mondragón-Contreras, L.; López-Callejas, R.; Torres-Bribiesca, M. A.; Peña-Eguiluz, R.

2013-11-01

Traditionally the electrical installations are designed for supplying power and to assure the personnel safety. In nuclear analysis laboratories, additional issues about grounding also must be considered for proper operation of high resolution nuclear spectroscopy systems. This paper shows the traditional ways of grounding nuclear spectroscopy systems and through different scenarios, it shows the effects on the more sensitive parameter of these systems: the energy resolution, it also proposes the constant monitoring of a power quality parameter as a way to preserve or to improve the resolution of the systems, avoiding the influence of excessive extrinsic noise.

Sewer System Management Plan.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holland, Robert C.

A Sewer System Management Plan (SSMP) is required by the State Water Resources Control Board (SWRCB) Order No. 2006-0003-DWQ Statewide General Waste Discharge Requirements (WDR) for Sanitary Sewer Systems (General Permit). DOE, National Nuclear Security Administration (NNSA), Sandia Field Office has filed a Notice of Intent to be covered under this General Permit. The General Permit requires a proactive approach to reduce the number and frequency of sanitary sewer overflows (SSOs) within the State. SSMPs must include provisions to provide proper and efficient management, operation, and maintenance of sanitary sewer systems and must contain a spill response plan.

A vibroacoustic diagnostic system as an element improving road transport safety.

PubMed

Komorska, Iwona

2013-01-01

Mechanical defects of a vehicle driving system can be dangerous on the road. Diagnostic systems, which monitor operations of electric and electronic elements and devices of vehicles, are continuously developed and improved, while defects of mechanical systems are still not managed properly. This article proposes supplementing existing on-board diagnostics with a system of diagnosing selected defects to minimize their impact. It presents a method of diagnosing mechanical defects of the engine, gearbox and other elements of the driving system on the basis of a model of the vibration signal obtained adaptively. This method is suitable for engine valves, engine head gasket, main gearbox, joints, etc.

Verifying Data Integrity of Electronically Scanned Pressure Systems at the NASA Glenn Research Center

NASA Technical Reports Server (NTRS)

Panek, Joseph W.

2001-01-01

The proper operation of the Electronically Scanned Pressure (ESP) System critical to accomplish the following goals: acquisition of highly accurate pressure data for the development of aerospace and commercial aviation systems and continuous confirmation of data quality to avoid costly, unplanned, repeat wind tunnel or turbine testing. Standard automated setup and checkout routines are necessary to accomplish these goals. Data verification and integrity checks occur at three distinct stages, pretest pressure tubing and system checkouts, daily system validation and in-test confirmation of critical system parameters. This paper will give an overview of the existing hardware, software and methods used to validate data integrity.

Relaxation in control systems of subdifferential type

NASA Astrophysics Data System (ADS)

Tolstonogov, A. A.

2006-02-01

In a separable Hilbert space we consider a control system with evolution operators that are subdifferentials of a proper convex lower semicontinuous function depending on time. The constraint on the control is given by a multivalued function with non-convex values that is lower semicontinuous with respect to the variable states. Along with the original system we consider the system in which the constraint on the control is the upper semicontinuous convex-valued regularization of the original constraint. We study relations between the solution sets of these systems. As an application we consider a control variational inequality. We give an example of a control system of parabolic type with an obstacle.

Pneumatic load compensating or controlling system

NASA Technical Reports Server (NTRS)

Rogers, J. R. (Inventor)

1975-01-01

A pneumatic load compensating or controlling system for restraining a load with a predetermined force or applying a predetermined force to the load is described; it includes a source of pressurized air, a one-way pneumatic actuator operatively connected to a load, and a fluid conduit fluidically connecting the actuator with the source of pressurized air. The actuator is of the piston and cylinder type, and the end of the fluid conduit is connected to the upper or lower portion of the cylinder whereby the actuator alternatively and selectively restrains the load with a predetermined force or apply a predetermined force to the load. Pressure regulators are included within the system for variably selectively adjusting the pressurized fluid to predetermined values as desired or required; a pressure amplifier is included within the system for multiplying the pressurized values so as to achieve greater load forces. An accumulator is incorporated within the system as a failsafe operating mechanism, and visual and aural alarm devices, operatively associated with pressure detecting apparatus, readily indicate the proper or improper functioning of the system.

Langley 8-foot high-temperature tunnel oxygen measurement system

NASA Technical Reports Server (NTRS)

Sprinkle, Danny R.; Chen, Tony D.; Chaturvedi, Sushil K.

1991-01-01

In order to ensure that there is a proper amount of oxygen necessary for sustaining test engine operation for hypersonic propulsion systems testing at the NASA Langley 8-foot high-temperature tunnel, a quickly responding real-time measurement system of test section oxygen concentration has been designed and tested at Langley. It is built around a zirconium oxide-based sensor which develops a voltage proportional to the oxygen partial pressure of the test gas. The voltage signal is used to control the amount of oxygen being injected into the combustor air. The physical operation of the oxygen sensor is described, as well as the sampling system used to extract the test gas from the tunnel test section. Results of laboratory tests conducted to verify sensor accuracy and response time performance are discussed, as well as the final configuration of the system to be installed in the tunnel.

Master Console System Monitoring and Control Development

NASA Technical Reports Server (NTRS)

Brooks, Russell A.

2013-01-01

The Master Console internship during the spring of 2013 involved the development of firing room displays at the John F. Kennedy Space Center (KSC). This position was with the Master Console Product Group (MCPG) on the Launch Control System (LCS) project. This project is responsible for the System Monitoring and Control (SMC) and Record and Retrieval (R&R) of launch operations data. The Master Console is responsible for: loading the correct software into each of the remaining consoles in the firing room, connecting the proper data paths to and from the launch vehicle and all ground support equipment, and initializing the entire firing room system to begin processing. During my internship, I developed a system health and status display for use by Master Console Operators (MCO) to monitor and verify the integrity of the servers, gateways, network switches, and firewalls used in the firing room.

Supporting the human life-raft in confronting the juggernaut of technology: Jens Rasmussen, 1961-1986.

PubMed

Kant, Vivek

2017-03-01

Jens Rasmussen's contribution to the field of human factors and ergonomics has had a lasting impact. Six prominent interrelated themes can be extracted from his research between 1961 and 1986. These themes form the basis of an engineering epistemology which is best manifested by his abstraction hierarchy. Further, Rasmussen reformulated technical reliability using systems language to enable a proper human-machine fit. To understand the concept of human-machine fit, he included the operator as a central component in the system to enhance system safety. This change resulted in the application of a qualitative and categorical approach for human-machine interaction design. Finally, Rasmussen's insistence on a working philosophy of systems design as being a joint responsibility of operators and designers provided the basis for averting errors and ensuring safe and correct system functioning. Copyright © 2016 Elsevier Ltd. All rights reserved.

Double-clad nuclear fuel safety rod

DOEpatents

McCarthy, William H.; Atcheson, Donald B.; Vaidyanathan, Swaminathan

1984-01-01

A device for shutting down a nuclear reactor during an undercooling or overpower event, whether or not the reactor's scram system operates properly. This is accomplished by double-clad fuel safety rods positioned at various locations throughout the reactor core, wherein melting of a secondary internal cladding of the rod allows the fuel column therein to shift from the reactor core to place the reactor in a subcritical condition.

Double-clad nuclear-fuel safety rod

DOEpatents

McCarthy, W.H.; Atcheson, D.B.

1981-12-30

A device for shutting down a nuclear reactor during an undercooling or overpower event, whether or not the reactor's scram system operates properly. This is accomplished by double-clad fuel safety rods positioned at various locations throughout the reactor core, wherein melting of a secondary internal cladding of the rod allows the fuel column therein to shift from the reactor core to place the reactor in a subcritical condition.

Operational considerations in monitoring oxygen levels at the National Transonic Facility

NASA Technical Reports Server (NTRS)

Zalenski, M. A.; Rowe, E. L.; Mcphee, J. R.

1985-01-01

Laboratory monitoring of the level of oxygen in sample gas mixtures is a process which can be performed with accurate and repeatable results. Operations at the National Transonic Facility require the storage and pumping of large volumes of liquid nitrogen. To protect against the possibility of a fault resulting in a localized oxygen deficient atmosphere, the facility is equipped with a monitoring system with an array of sensors. During the early operational stages, the system produced recurrent alarms, none of which could be traced to a true oxygen deficiency. A thorough analysis of the system was undertaken with primary emphasis placed on the sensor units. These units sense the partial pressure of oxygen which, after signal conditioning, is presented as a % by volume indication at the system output. It was determined that many of the problems experienced were due to a lack of proper accounting for the partial pressure/% by volume relationship, with a secondary cause being premature sensor failure. Procedures were established to consider atmospherically induced partial pressure variations. Sensor rebuilding techniques were examined, and those elements contributing to premature sensor failure were identified. The system now operates with a high degree of confidence and reliability.

Reactive documentation system

NASA Astrophysics Data System (ADS)

Boehnlein, Thomas R.; Kramb, Victoria

2018-04-01

Proper formal documentation of computer acquired NDE experimental data generated during research is critical to the longevity and usefulness of the data. Without documentation describing how and why the data was acquired, NDE research teams lose capability such as their ability to generate new information from previously collected data or provide adequate information so that their work can be replicated by others seeking to validate their research. Despite the critical nature of this issue, NDE data is still being generated in research labs without appropriate documentation. By generating documentation in series with data, equal priority is given to both activities during the research process. One way to achieve this is to use a reactive documentation system (RDS). RDS prompts an operator to document the data as it is generated rather than relying on the operator to decide when and what to document. This paper discusses how such a system can be implemented in a dynamic environment made up of in-house and third party NDE data acquisition systems without creating additional burden on the operator. The reactive documentation approach presented here is agnostic enough that the principles can be applied to any operator controlled, computer based, data acquisition system.

Closed-loop helium circulation system for actuation of a continuously operating heart catheter pump.

PubMed

Karabegovic, Alen; Hinteregger, Markus; Janeczek, Christoph; Mohl, Werner; Gföhler, Margit

2017-06-09

Currently available, pneumatic-based medical devices are operated using closed-loop pulsatile or open continuous systems. Medical devices utilizing gases with a low atomic number in a continuous closed loop stream have not been documented to date. This work presents the construction of a portable helium circulation addressing the need for actuating a novel, pneumatically operated catheter pump. The design of its control system puts emphasis on the performance, safety and low running cost of the catheter pump. Static and dynamic characteristics of individual elements in the circulation are analyzed to ensure a proper operation of the system. The pneumatic circulation maximizes the working range of the drive unit inside the catheter pump while reducing the total size and noise production.Separate flow and pressure controllers position the turbine's working point into the stable region of the pressure creation element. A subsystem for rapid gas evacuation significantly decreases the duration of helium removal after a leak, reaching subatmospheric pressure in the intracorporeal catheter within several milliseconds. The system presented in the study offers an easy control of helium mass flow while ensuring stable behavior of its internal components.

45 CFR 170.423 - Principles of proper conduct for ONC-ATCBs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 45 Public Welfare 1 2010-10-01 2010-10-01 false Principles of proper conduct for ONC-ATCBs. 170... § 170.423 Principles of proper conduct for ONC-ATCBs. An ONC-ATCB shall: (a) Operate its certification... EHR Module developer conspicuously include the following text on its Web site and in all marketing...

An Evaluation of the Vapor Phase Catalytic Ammonia Removal Process for Use in a Mars Transit Vehicle

NASA Technical Reports Server (NTRS)

Flynn, Michael; Borchers, Bruce

1998-01-01

An experimental program has been developed to evaluate the potential of the Vapor Phase Catalytic Ammonia Reduction (VPCAR) technology for use as a Mars Transit Vehicle water purification system. Design modifications which will be required to ensure proper operation of the VPCAR system in reduced gravity are also evaluated. The VPCAR system is an integrated wastewater treatment technology that combines a distillation process with high temperature catalytic oxidation. The distillation portion of the system utilizes a vapor compression distillation process to provide an energy efficient phase change separation. This portion of the system removes any inorganic salts and large molecular weight, organic contaminates, i.e., non-volatile, from the product water stream and concentrates these contaminates into a byproduct stream. To oxidize the volatile organic compounds and ammonia, a vapor phase, high temperature catalytic oxidizer is used. This catalytic system converts these compounds along with the aqueous product into CO2, H2O, and N2O. A secondary catalytic bed can then be used to reduce the N2O to nitrogen and oxygen (although not evaluated in this study). This paper describes the design specification of the VPCAR process, the relative benefits of its utilization in a Mars Transit Vehicle, and the design modification which will be required to ensure its proper operation in reduced gravity. In addition, the results of an experimental evaluation of the processors is presented. This evaluation presents the processors performance based upon product water purity, water recovery rates, and power.

Shuttle cryogenic supply system optimization study. Volume 5A-1: Users manual for math models

NASA Technical Reports Server (NTRS)

1973-01-01

The Integrated Math Model for Cryogenic Systems is a flexible, broadly applicable systems parametric analysis tool. The program will effectively accommodate systems of considerable complexity involving large numbers of performance dependent variables such as are found in the individual and integrated cryogen systems. Basically, the program logic structure pursues an orderly progression path through any given system in much the same fashion as is employed for manual systems analysis. The system configuration schematic is converted to an alpha-numeric formatted configuration data table input starting with the cryogen consumer and identifying all components, such as lines, fittings, and valves, each in its proper order and ending with the cryogen supply source assembly. Then, for each of the constituent component assemblies, such as gas generators, turbo machinery, heat exchangers, and accumulators, the performance requirements are assembled in input data tabulations. Systems operating constraints and duty cycle definitions are further added as input data coded to the configuration operating sequence.

Entanglement branching operator

NASA Astrophysics Data System (ADS)

Harada, Kenji

2018-01-01

We introduce an entanglement branching operator to split a composite entanglement flow in a tensor network which is a promising theoretical tool for many-body systems. We can optimize an entanglement branching operator by solving a minimization problem based on squeezing operators. The entanglement branching is a new useful operation to manipulate a tensor network. For example, finding a particular entanglement structure by an entanglement branching operator, we can improve a higher-order tensor renormalization group method to catch a proper renormalization flow in a tensor network space. This new method yields a new type of tensor network states. The second example is a many-body decomposition of a tensor by using an entanglement branching operator. We can use it for a perfect disentangling among tensors. Applying a many-body decomposition recursively, we conceptually derive projected entangled pair states from quantum states that satisfy the area law of entanglement entropy.

On the effects of adaptive reservoir operating rules in hydrological physically-based models

NASA Astrophysics Data System (ADS)

Giudici, Federico; Anghileri, Daniela; Castelletti, Andrea; Burlando, Paolo

2017-04-01

Recent years have seen a significant increase of the human influence on the natural systems both at the global and local scale. Accurately modeling the human component and its interaction with the natural environment is key to characterize the real system dynamics and anticipate future potential changes to the hydrological regimes. Modern distributed, physically-based hydrological models are able to describe hydrological processes with high level of detail and high spatiotemporal resolution. Yet, they lack in sophistication for the behavior component and human decisions are usually described by very simplistic rules, which might underperform in reproducing the catchment dynamics. In the case of water reservoir operators, these simplistic rules usually consist of target-level rule curves, which represent the average historical level trajectory. Whilst these rules can reasonably reproduce the average seasonal water volume shifts due to the reservoirs' operation, they cannot properly represent peculiar conditions, which influence the actual reservoirs' operation, e.g., variations in energy price or water demand, dry or wet meteorological conditions. Moreover, target-level rule curves are not suitable to explore the water system response to climate and socio economic changing contexts, because they assume a business-as-usual operation. In this work, we quantitatively assess how the inclusion of adaptive reservoirs' operating rules into physically-based hydrological models contribute to the proper representation of the hydrological regime at the catchment scale. In particular, we contrast target-level rule curves and detailed optimization-based behavioral models. We, first, perform the comparison on past observational records, showing that target-level rule curves underperform in representing the hydrological regime over multiple time scales (e.g., weekly, seasonal, inter-annual). Then, we compare how future hydrological changes are affected by the two modeling approaches by considering different future scenarios comprising climate change projections of precipitation and temperature and projections of electricity prices. We perform this comparative assessment on the real-world water system of Lake Como catchment in the Italian Alps, which is characterized by the massive presence of artificial hydropower reservoirs heavily altering the natural hydrological regime. The results show how different behavioral model approaches affect the system representation in terms of hydropower performance, reservoirs dynamics and hydrological regime under different future scenarios.

The stem cell laboratory: design, equipment, and oversight.

PubMed

Wesselschmidt, Robin L; Schwartz, Philip H

2011-01-01

This chapter describes some of the major issues to be considered when setting up a laboratory for the culture of human pluripotent stem cells (hPSCs). The process of establishing a hPSC laboratory can be divided into two equally important parts. One is completely administrative and includes developing protocols, seeking approval, and establishing reporting processes and documentation. The other part of establishing a hPSC laboratory involves the physical plant and includes design, equipment and personnel. Proper planning of laboratory operations and proper design of the physical layout of the stem cell laboratory so that meets the scope of planned operations is a major undertaking, but the time spent upfront will pay long-term returns in operational efficiency and effectiveness. A well-planned, organized, and properly equipped laboratory supports research activities by increasing efficiency and reducing lost time and wasted resources.

Wind Farm Flow Modeling using an Input-Output Reduced-Order Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Annoni, Jennifer; Gebraad, Pieter; Seiler, Peter

Wind turbines in a wind farm operate individually to maximize their own power regardless of the impact of aerodynamic interactions on neighboring turbines. There is the potential to increase power and reduce overall structural loads by properly coordinating turbines. To perform control design and analysis, a model needs to be of low computational cost, but retains the necessary dynamics seen in high-fidelity models. The objective of this work is to obtain a reduced-order model that represents the full-order flow computed using a high-fidelity model. A variety of methods, including proper orthogonal decomposition and dynamic mode decomposition, can be used tomore » extract the dominant flow structures and obtain a reduced-order model. In this paper, we combine proper orthogonal decomposition with a system identification technique to produce an input-output reduced-order model. This technique is used to construct a reduced-order model of the flow within a two-turbine array computed using a large-eddy simulation.« less

Techniques utilized in the simulated altitude testing of a 2D-CD vectoring and reversing nozzle

NASA Technical Reports Server (NTRS)

Block, H. Bruce; Bryant, Lively; Dicus, John H.; Moore, Allan S.; Burns, Maureen E.; Solomon, Robert F.; Sheer, Irving

1988-01-01

Simulated altitude testing of a two-dimensional, convergent-divergent, thrust vectoring and reversing exhaust nozzle was accomplished. An important objective of this test was to develop test hardware and techniques to properly operate a vectoring and reversing nozzle within the confines of an altitude test facility. This report presents detailed information on the major test support systems utilized, the operational performance of the systems and the problems encountered, and test equipment improvements recommended for future tests. The most challenging support systems included the multi-axis thrust measurement system, vectored and reverse exhaust gas collection systems, and infrared temperature measurement systems used to evaluate and monitor the nozzle. The feasibility of testing a vectoring and reversing nozzle of this type in an altitude chamber was successfully demonstrated. Supporting systems performed as required. During reverser operation, engine exhaust gases were successfully captured and turned downstream. However, a small amount of exhaust gas spilled out the collector ducts' inlet openings when the reverser was opened more than 60 percent. The spillage did not affect engine or nozzle performance. The three infrared systems which viewed the nozzle through the exhaust collection system worked remarkably well considering the harsh environment.

Debris/Ice/TPS Assessment and Integrated Photographic Analysis of Shuttle Mission STS-109

NASA Technical Reports Server (NTRS)

Oliu, Armando

2005-01-01

The Debris Team has developed and implemented measures to control damage from debris in the Shuttle operational environment and to make the control measures a part of routine launch flows. These measures include engineering surveillance during vehicle processing and closeout operations, facility and flight hardware inspections before and after launch, and photographic analysis of mission events. Photographic analyses of mission imagery from launch, on-orbit, and landing provide significant data in verifying proper operation of systems and evaluating anomalies. In addition to the Kennedy Space Center Photo/Video Analysis, reports from Johnson Space Center and Marshall Space Flight Center are also included in this document to provide an integrated assessment of the mission.

Debris/Ice/TPS Assessment and Integrated Photographic Analysis of Shuttle Mission STS-110

NASA Technical Reports Server (NTRS)

Oliu, Armando

2005-01-01

The Debris Team has developed and implemented measures to control damage from debris in the Shuttle operational environment and to make the control measures a part of routine launch flows. These measures include engineering surveillance during vehicle processing and closeout operations, facility and flight hardware inspections before and after launch, and photographic analysis of mission events. Photographic analyses of mission imagery from launch, on-orbit, and landing provide significant data in verifying proper operation of systems and evaluating anomalies. In addition to the Kennedy Space Center Photo/Video Analysis, reports from Johnson Space Center and Marshall Space Flight Center are also included in this document to provide an integrated assessment of the mission.

Debris/Ice/TPS Assessment and Integrated Photographic Analysis of Shuttle Mission STS-105

NASA Technical Reports Server (NTRS)

Oliu, Armando

2005-01-01

The Debris Team has developed and implemented measures to control damage from debris in the Shuttle operational environment and to make the control measures a part of routine launch flows. These measures include engineering surveillance during vehicle processing and closeout operations, facility and flight hardware inspections before and after launch, and photographic analysis of mission events. Photographic analyses of mission imagery from launch, on-orbit, and landing provide significant data in verifying proper operation of systems and evaluating anomalies. In addition to the Kennedy Space Center Photo/Video Analysis, reports from Johnson Space Center and Marshall Space Flight Center are also included in this document to provide an integrated assessment of the mission.

Debris/Ice/TPS Assessment and Integrated Photographic Analysis of Shuttle Mission STS-104

NASA Technical Reports Server (NTRS)

Oliu, Armando

2005-01-01

The Debris Team has developed and implemented measures to control damage from debris in the Shuttle operational environment and to make the control measures a part of routine launch flows. These measures include engineering surveillance during vehicle processing and closeout operations, facility and flight hardware inspections before and after launch, and photographic analysis of mission events. Photographic analyses of mission imagery from launch, on-orbit, and landing provide significant data in verifying proper operation of systems and evaluating anomalies. In addition to the Kennedy Space Center Photo/Video Analysis, reports from Johnson Space Center and Marshall Space Flight Center are also included in this document to provide an integrated assessment of the mission.

Debris/Ice/TPS Assessment and Integrated Photographic Analysis of Shuttle Mission STS-108

NASA Technical Reports Server (NTRS)

Oliu, Armando

2005-01-01

The Debris Team has developed and implemented measures to control damage from debris in the Shuttle operational environment and to make the control measures a part of routine launch flows. These measures include engineering surveillance during vehicle processing and closeout operations, facility and flight hardware inspections before and after launch, and photographic analysis of mission events. Photographic analyses of mission imagery from launch, on-orbit, and landing provide significant data in verifying proper operation of systems and evaluating anomalies. In addition to the Kennedy Space Center Photo/Video Analysis, reports from Johnson Space Center and Marshall Space Flight Center are also included in this document to provide an integrated assessment of the mission.

Wideband fiber optic communications link

NASA Astrophysics Data System (ADS)

Bray, J. R.

1984-12-01

This thesis examined the feasibility of upgrading a nine port fiber optic bundle telecommunications system to a single strand fiber optic system. Usable pieces of equipment were identified and new Light Emitting Diodes (LED), Photodetectors and single strand SMA styled fiber optic connectors were ordered. Background research was conducted in the area of fiber optic power launching, fiber losses, connector losses and efficiencies. A new modulation/demodulation circuit was designed and constructed using parts from unused equipment. A new front panel was constructed to house the components, switches and connectors. A 2-m piece of optical fiber was terminated with the new connectors and tested for connector loss, numeric aperture and attenuation. The new LED was characterized by its emission radiation pattern and the entire system was tested for functional operation, frequency response and bandwidth of operation. An operations manual was prepared to ensure proper use in the future. The result was a two piece, single strand, fiber optic communications systems fully TTL compatible, capable of transmitting digital signals from 80 Kbit/sec to 20 Mbit/sec. The system was tested in a half duplex mode using both baseband and carrier modulated signals.

Space station ECLSS simplified integrated test

NASA Technical Reports Server (NTRS)

Schunk, Richard G.; Bagdigian, Robert M.; Carrasquillo, Robyn L.; Ogle, Kathyrn Y.; Wieland, Paul O.

1989-01-01

A discussion of the Space Station Simplified Integrated Test (SIT) was conducted. The first in a series of three integrated Environmental Control and Life Support (ECLS) system tests, the primary objectives of the SIT were to verify proper operation of ECLS subsystems functioning in an integrated fashion as well as to gather preliminary performance data for the partial ECLS system used in the test. A description of the SIT configuration, a summary of events, a discussion of anomalies that occurred during the test, and detailed results and analysis from individual measurements and water and gas samples taken during the test are included. The preprototype ECLS hardware used in the test is reported providing an overall process description and theory of operation for each hardware item.

Microgrid Controllers : Expanding Their Role and Evaluating Their Performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maitra, Arindam; Pratt, Annabelle; Hubert, Tanguy

Microgrids have long been deployed to provide power to customers in remote areas as well as critical industrial and military loads. Today, they are also being proposed as grid-interactive solutions for energy-resilient communities. Such microgrids will spend most of the time operating while synchronized with the surrounding utility grid but will also be capable of separating during contingency periods due to storms or temporary disturbances such as local grid faults. Properly designed and grid-integrated microgrids can provide the flexibility, reliability, and resiliency needs of both the future grid and critical customers. These systems can be an integral part of futuremore » power system designs that optimize investments to achieve operational goals, improved reliability, and diversification of energy sources.« less

Systematic Evaluation of Stochastic Methods in Power System Scheduling and Dispatch with Renewable Energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Yishen; Zhou, Zhi; Liu, Cong

2016-08-01

As more wind power and other renewable resources are being integrated into the electric power grid, the forecast uncertainty brings operational challenges for the power system operators. In this report, different operational strategies for uncertainty management are presented and evaluated. A comprehensive and consistent simulation framework is developed to analyze the performance of different reserve policies and scheduling techniques under uncertainty in wind power. Numerical simulations are conducted on a modified version of the IEEE 118-bus system with a 20% wind penetration level, comparing deterministic, interval, and stochastic unit commitment strategies. The results show that stochastic unit commitment provides amore » reliable schedule without large increases in operational costs. Moreover, decomposition techniques, such as load shift factor and Benders decomposition, can help in overcoming the computational obstacles to stochastic unit commitment and enable the use of a larger scenario set to represent forecast uncertainty. In contrast, deterministic and interval unit commitment tend to give higher system costs as more reserves are being scheduled to address forecast uncertainty. However, these approaches require a much lower computational effort Choosing a proper lower bound for the forecast uncertainty is important for balancing reliability and system operational cost in deterministic and interval unit commitment. Finally, we find that the introduction of zonal reserve requirements improves reliability, but at the expense of higher operational costs.« less

40 CFR 62.14442 - What must my inspection include?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) Inspect HMIWI door and door gaskets for proper sealing; (f) Inspect motors for proper operation; (g... incinerator shell for corrosion and/or hot spots; (i) Inspect secondary/tertiary chamber and stack, and clean...

40 CFR 62.14442 - What must my inspection include?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) Inspect HMIWI door and door gaskets for proper sealing; (f) Inspect motors for proper operation; (g... incinerator shell for corrosion and/or hot spots; (i) Inspect secondary/tertiary chamber and stack, and clean...

40 CFR 62.14442 - What must my inspection include?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Inspect HMIWI door and door gaskets for proper sealing; (f) Inspect motors for proper operation; (g... incinerator shell for corrosion and/or hot spots; (i) Inspect secondary/tertiary chamber and stack, and clean...

Hold-up power supply for flash memory

NASA Technical Reports Server (NTRS)

Ott, William E. (Inventor)

2004-01-01

A hold-up power supply for flash memory systems is provided. The hold-up power supply provides the flash memory with the power needed to temporarily operate when a power loss exists. This allows the flash memory system to complete any erasures and writes, and thus allows it to shut down gracefully. The hold-up power supply detects when a power loss on a power supply bus is occurring and supplies the power needed for the flash memory system to temporally operate. The hold-up power supply stores power in at least one capacitor. During normal operation, power from a high voltage supply bus is used to charge the storage capacitors. When a power supply loss is detected, the power supply bus is disconnected from the flash memory system. A hold-up controller controls the power flow from the storage capacitors to the flash memory system. The hold-up controller uses feedback to assure that the proper voltage is provided from the storage capacitors to the flash memory system. This power supplied by the storage capacitors allows the flash memory system to complete any erasures and writes, and thus allows the flash memory system to shut down gracefully.

Serial Interface through Stream Protocol on EPICS Platform for Distributed Control and Monitoring

NASA Astrophysics Data System (ADS)

Das Gupta, Arnab; Srivastava, Amit K.; Sunil, S.; Khan, Ziauddin

2017-04-01

Remote operation of any equipment or device is implemented in distributed systems in order to control and proper monitoring of process values. For such remote operations, Experimental Physics and Industrial Control System (EPICS) is used as one of the important software tool for control and monitoring of a wide range of scientific parameters. A hardware interface is developed for implementation of EPICS software so that different equipment such as data converters, power supplies, pump controllers etc. could be remotely operated through stream protocol. EPICS base was setup on windows as well as Linux operating system for control and monitoring while EPICS modules such as asyn and stream device were used to interface the equipment with standard RS-232/RS-485 protocol. Stream Device protocol communicates with the serial line with an interface to asyn drivers. Graphical user interface and alarm handling were implemented with Motif Editor and Display Manager (MEDM) and Alarm Handler (ALH) command line channel access utility tools. This paper will describe the developed application which was tested with different equipment and devices serially interfaced to the PCs on a distributed network.

Human-Centered Automation: The View from Earth Versus the View from Mars

NASA Technical Reports Server (NTRS)

Massimino, Michael J.; Smith, Philip J.; Stilwell, Donald J.; Mitchell, Christine M.; Thurman, David A.; Malin, Jane T.; Jones, Patricia M.

1999-01-01

This panel addresses the topic of human-centered automation in, however, a very different context-manned missions to deep space in which predominantly autonomous systems must control the crew's life-support systems most of the time. The Mars spacecraft and its inhabitants are totally dependent on the proper operation of thousands of control loops and pieces of equipment to maintain the delicate, unbuffered homeostasis of their remote existence. Mission success hangs on a thread that depends on a successful partnership, or symbiosis. between crew and machines, which exceeds anything ever required of ground systems. The need for a new approach to human-centered automation is not a "frill" in future Mars mission, but rather a sine qua non of survival. Thus the issue is design: Can we design systems intended to operate in a predominantly autonomous mode. without a human backup, that are sufficiently safe such that human travel into deep space is possible?

Modeling Load Dynamics to Support Resiliency-based Operations in Low-Inertia Microgrids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tuffner, Francis K.; Schneider, Kevin P.; Hansen, Jacob

Microgrids have repeatedly demonstrated the ability to provide uninterrupted service to critical end-use loads during normal outages, severe weather events, and natural disasters. While their ability to provide critical services is well documented, microgrids present a more dynamic operational environment than grid-connected distribution systems. The electrodynamics of a microgrid are commonly driven by the high inertia of rotating generators, which are common in many microgrids. In such high-inertia systems, the impact of end-use load electromechanical dynamics are often not examined. However, with the increased penetration of inverter-based generation with little or no inertia, it is necessary to consider the impactmore » that the dynamics of the end-use loads have on the operations of microgrids, particularly for a resiliency-based operation. These operations include, but are not limited to, switching operations, loss of generating units, and the starting of induction motors. This paper examines the importance of including multi-state electromechanical dynamic models of the end-use load when evaluating the operations of low inertia microgrids, and shows that by properly representing their behavior, it is possible to cost effectively size equipment while supporting resilient operations of critical end-use loads.« less

Modeling Load Dynamics to Support Resiliency-based Operations in Low-Inertia Microgrids

DOE PAGES

Tuffner, Francis K.; Schneider, Kevin P.; Hansen, Jacob; ...

2018-03-07

Microgrids have repeatedly demonstrated the ability to provide uninterrupted service to critical end-use loads during normal outages, severe weather events, and natural disasters. While their ability to provide critical services is well documented, microgrids present a more dynamic operational environment than grid-connected distribution systems. The electrodynamics of a microgrid are commonly driven by the high inertia of rotating generators, which are common in many microgrids. In such high-inertia systems, the impact of end-use load electromechanical dynamics are often not examined. However, with the increased penetration of inverter-based generation with little or no inertia, it is necessary to consider the impactmore » that the dynamics of the end-use loads have on the operations of microgrids, particularly for a resiliency-based operation. These operations include, but are not limited to, switching operations, loss of generating units, and the starting of induction motors. This paper examines the importance of including multi-state electromechanical dynamic models of the end-use load when evaluating the operations of low inertia microgrids, and shows that by properly representing their behavior, it is possible to cost effectively size equipment while supporting resilient operations of critical end-use loads.« less

Inference Engine in an Intelligent Ship Course-Keeping System

PubMed Central

2017-01-01

The article presents an original design of an expert system, whose function is to automatically stabilize ship's course. The focus is put on the inference engine, a mechanism that consists of two functional components. One is responsible for the construction of state space regions, implemented on the basis of properly processed signals recorded by sensors from the input and output of an object. The other component is responsible for generating a control decision based on the knowledge obtained in the first module. The computing experiments described herein prove the effective and correct operation of the proposed system. PMID:29317859

ATAD control goals through the analysis of process variables and evaluation of quality, production and cost.

PubMed

Nájera, S; Gil-Martínez, M; Zambrano, J A

2015-01-01

The aim of this paper is to establish and quantify different operational goals and control strategies in autothermal thermophilic aerobic digestion (ATAD). This technology appears as an alternative to conventional sludge digestion systems. During the batch-mode reaction, high temperatures promote sludge stabilization and pasteurization. The digester temperature is usually the only online, robust, measurable variable. The average temperature can be regulated by manipulating both the air injection and the sludge retention time. An improved performance of diverse biochemical variables can be achieved through proper manipulation of these inputs. However, a better quality of treated sludge usually implies major operating costs or a lower production rate. Thus, quality, production and cost indices are defined to quantify the outcomes of the treatment. Based on these, tradeoff control strategies are proposed and illustrated through some examples. This paper's results are relevant to guide plant operators, to design automatic control systems and to compare or evaluate the control performance on ATAD systems.

Water Recovery System Design to Accommodate Dormant Periods for Manned Missions

NASA Technical Reports Server (NTRS)

Tabb, David; Carter, Layne

2015-01-01

Future manned missions beyond lower Earth orbit may include intermittent periods of extended dormancy. Under the NASA Advanced Exploration System (AES) project, NASA personnel evaluated the viability of the ISS Water Recovery System (WRS) to support such a mission. The mission requirement includes the capability for life support systems to support crew activity, followed by a dormant period of up to one year, and subsequently for the life support systems to come back online for additional crewed missions. Dormancy could be a critical issue due to concerns with microbial growth or chemical degradation that might prevent water systems from operating properly when the crewed mission began. As such, it is critical that the water systems be designed to accommodate this dormant period. This paper details the results of this evaluation, which include identification of dormancy issues, results of testing performed to assess microbial stability of pretreated urine during dormancy periods, and concepts for updating to the WRS architecture and operational concepts that will enable the ISS WRS to support the dormancy requirement.

Integrated scheduling of a container handling system with simultaneous loading and discharging operations

NASA Astrophysics Data System (ADS)

Li, Chen; Lu, Zhiqiang; Han, Xiaole; Zhang, Yuejun; Wang, Li

2016-03-01

The integrated scheduling of container handling systems aims to optimize the coordination and overall utilization of all handling equipment, so as to minimize the makespan of a given set of container tasks. A modified disjunctive graph is proposed and a mixed 0-1 programming model is formulated. A heuristic algorithm is presented, in which the original problem is divided into two subproblems. In the first subproblem, contiguous bay crane operations are applied to obtain a good quay crane schedule. In the second subproblem, proper internal truck and yard crane schedules are generated to match the given quay crane schedule. Furthermore, a genetic algorithm based on the heuristic algorithm is developed to search for better solutions. The computational results show that the proposed algorithm can efficiently find high-quality solutions. They also indicate the effectiveness of simultaneous loading and discharging operations compared with separate ones.

An Overview of Dynamic Contact Resistance Measurement of HV Circuit Breakers

NASA Astrophysics Data System (ADS)

Bhole, A. A.; Gandhare, W. Z.

2016-06-01

With the deregulation of the electrical power industry, utilities and service companies are operating in a changing business environment. High voltage circuit breakers are extremely important for the function of modern electric power supply systems. The need to predict the proper function of circuit breaker grew over the years as the transmission networks expanded. The maintenance of circuit breakers deserves special consideration because of their importance for routine switching and for protection of other equipments. Electric transmission system breakups and equipment destruction can occur if a circuit breaker fails to operate because of a lack of preventive maintenance. Dynamic Contact Resistance Measurement (DCRM) is known as an effective technique for assessing the condition of power circuit breakers contacts and operating mechanism. This paper gives a general review about DCRM. It discusses the practical case studies on use of DCRM for condition assessment of high voltage circuit breakers.

Operation of a single-channel, sequential Navstar GPS receiver in a helicopter mission environment

NASA Technical Reports Server (NTRS)

Edwards, F. G.; Hamlin, J. R.

1984-01-01

It is pointed out that the future utilization of the Navstar Global Positioning System (GPS) by civil helicopters will provide an enhanced performance not obtainable with current navigations systems. GPS will supply properly equipped users with extremely accurate three-dimensional position and velocity information anywhere in the world. Preliminary studies have been conducted to investigate differential GPS concept mechanizations and cost, and to theoretically predict navigation performance and the impact of degradation of the GPS C/A code for national security considerations. The obtained results are encouraging, but certain improvements are needed. As a second step in the program, a single-channel sequential GPS navigator was installed and operated in the NASA SH-3G helicopter. A series of flight tests were conducted. It is found that performance of the Navstar GPS Z-set is quite acceptable to support area navigation and nonprecision approach operations.

Emergency membrane contactor based absorption system for ammonia leaks in water treatment plants.

PubMed

Shao, Jiahui; Fang, Xuliang; He, Yiliang; Jin, Qiang

2008-01-01

Abstract Because of the suspected health risks of trihalomethanes (THMs), more and more water treatment plants have replaced traditional chlorine disinfection process with chloramines but often without the proper absorption system installed in the case of ammonia leaks in the storage room. A pilot plant membrane absorption system was developed and installed in a water treatment plant for this purpose. Experimentally determined contact angle, surface tension, and corrosion tests indicated that the sulfuric acid was the proper choice as the absorbent for leaking ammonia using polypropylene hollow fiber membrane contactor. Effects of several operating conditions on the mass transfer coefficient, ammonia absorption, and removal efficiency were examined, including the liquid concentration, liquid velocity, and feed gas concentration. Under the operation conditions investigated, the gas absorption efficiency over 99.9% was achieved. This indicated that the designed pilot plant membrane absorption system was effective to absorb the leaking ammonia in the model storage room. The removal rate of the ammonia in the model storage room was also experimentally and theoretically found to be primarily determined by the ammonia suction flow rate from the ammonia storage room to the membrane contactor. The ammonia removal rate of 99.9% was expected to be achieved within 1.3 h at the ammonia gas flow rate of 500 m3/h. The success of the pilot plant membrane absorption system developed in this study illustrated the potential of this technology for ammonia leaks in water treatment plant, also paved the way towards a larger scale application.

Alternatives to ozone depleting refrigerants in test equipment

NASA Technical Reports Server (NTRS)

Hall, Richard L.; Johnson, Madeleine R.

1995-01-01

This paper describes the initial results of a refrigerant retrofit project at the Aerospace Guidance and Metrology Center (AGMC) at Newark Air Force Base, Ohio. The objective is to convert selected types of test equipment to properly operate on hydrofluorocarbon (HFC) alternative refrigerants, having no ozone depleting potential, without compromising system reliability or durability. This paper discusses the primary technical issues and summarizes the test results for 17 different types of test equipment: ten environmental chambers, two ultralow temperature freezers, two coolant recirculators, one temperature control unit, one vapor degreaser, and one refrigerant recovery system. The postconversion performance test results have been very encouraging: system capacity and input power remained virtually unchanged. In some cases, the minimum operating temperature increased by a few degrees as a result of the conversion, but never beyond AGMC's functional requirements.

Medical Gas Analyzer

NASA Technical Reports Server (NTRS)

1983-01-01

The Remote Monitoring System (RMS) is manufactured by Perkin Elmer Corporation. The principal component of the RMS was originally developed for spacecraft use to monitor astronaut's respiratory gases in NASA's Gemini and Apollo program. At Wishard Memorial Hospital in Indianapolis, IN, the RMS is used in operating rooms for analysis of anesthetic gases and measurement of oxygen, carbon dioxide and nitrogen concentrations. It assures that the patient undergoing surgery has the proper breathing environment.

Management Academy LANL Business Systems: Property Management, Course #31036

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shepherd, Michael J.; Rinke, Helen Mae; Hanson, Todd

Los Alamos National Laboratory (LANL) is responsible for the efficient economical management of all government property in its stewardship. This training explains the role LANL managers have in managing, controlling, and disposing of government property. The Laboratory's goal is good asset management. By properly managing property across the facility, Laboratory managers can help ASM improve government property utilization and extend asset life, while reducing asset-related operating costs and expenditures.

Worldwide Environmental Compliance Assessment and Management Program (ECAMP)

DTIC Science & Technology

1991-01-01

shop is derived as follows: 1. The paint shop has many enviromnntal concerns: -wi - - emissions from painting activities -proper storae of flammable and...stripping compounds, and paint solids into the storm or sanitary systems. Protocols tit apply are: -Air Emissions M en n -Haarous Materials Mr~nn...in Air Emissions an ~enr spray painiM or surface coating operations questions - in Hazarious Materials Mas enx storage of flanmble/combustible

Reevaluating the United States’ Approach to Conflict and Military Intervention

DTIC Science & Technology

2009-12-11

conflict. This paradigm views conflict as a legitimate incompatibly of interests between parties caused by scarcity of resources, power imbalances...if the problem is properly framed and the parties are able to work together. The systems perspective uses the biological metaphor of a simple...and resolution that could increase the US military’s effectiveness in its current operations? Significance There is a plethora of research and theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olsen, Tim; Preus, Robert

Site assessment for small wind energy systems is one of the key factors in the successful installation, operation, and performance of a small wind turbine. A proper site assessment is a difficult process that includes wind resource assessment and the evaluation of site characteristics. These guidelines address many of the relevant parts of a site assessment with an emphasis on wind resource assessment, using methods other than on-site data collection and creating a small wind site assessment report.

Jet Engine Control Using Ethernet with a BRAIN (Postprint)

DTIC Science & Technology

2008-07-01

current communications may be mitigated. 15. SUBJECT TERMS BRAIN, Braided Ring Availability Integrity Network, Gas turbine, FADEC , disturbed...urrent state of the art engine controls have converged on the notion of the Full Authority Digital Engine Control ( FADEC ), which consists of a centralized...is completely dependent on the proper operation of the controller. In current systems, the FADEC is often located on the relatively cool engine fan

Adjunctation and Scalar Product in the Dirac Equation - II

NASA Astrophysics Data System (ADS)

Dima, M.

2017-02-01

Part-I Dima (Int. J. Theor. Phys. 55, 949, 2016) of this paper showed in a representation independent way that γ 0 is the Bergmann-Pauli adjunctator of the Dirac { γ μ } set. The distiction was made between similarity (MATH) transformations and PHYS transformations - related to the (covariant) transformations of physical quantities. Covariance is due solely to the gauging of scalar products between systems of reference and not to the particular action of γ 0 on Lorentz boosts - a matter that in the past led inadvertently to the definition of a second scalar product (the Dirac-bar product). Part-II shows how two scalar products lead to contradictions and eliminates this un-natural duality in favour of the canonical scalar product and its gauge between systems of reference. What constitutes a proper observable is analysed and for instance spin is revealed not to embody one (except as projection on the boost direction - helicity). A thorough investigation into finding a proper-observable current for the theory shows that the Dirac equation does not possess one in operator form. A number of problems with the Dirac current operator are revealed - its Klein-Gordon counterpart being significantly more physical. The alternative suggested is finding a current for the Dirac theory in scalar form j^{μ } = < ρ rangle _{_{ψ }}v^{μ }_{ψ }.

16 CFR 1512.19 - Instructions and labeling.

Code of Federal Regulations, 2010 CFR

2010-01-01

... road operation. (2) Assembly instructions for accomplishing complete and proper assembly. (3) Maintenance instructions for proper maintenance of brakes, control cables, bearing adjustments, wheel... determine that such maintenance is beyond the capability of the consumer, specifics regarding locations...

Inverter for Interchangeable Use as Current Source Inverter and Voltage Source Inverter for Interconnecting to Grid

NASA Astrophysics Data System (ADS)

Teruya, Daisuke; Masukawa, Shigeo; Iida, Shoji

We propose a novel inverter that can be operated either as a Current Source Inverter (CSI) or as a Voltage Source Inverter (VSI) by changing only the control signals. It is proper to apply it to the interconnecting system with renewal energy, such as photovoltaic cells or wind generation systems, to a grid. This inverter is usually operated as the CSI connected to the grid. Even if the energy source has a lower voltage than the grid, the energy can be supplied to the grid through the proposed inverter. The power factor can be briefly maintained at almost unity. When power supply from the grid is interrupted, the proposed circuit should be operated as the VSI in the stand-alone operation mode. In this way, the circuit can maintain a constant output voltage to the loads. In this paper, the proposed circuit configuration and the control schemes for both the CSI and the VSI are described. Further, the circuit characteristics for both are discussed experimentally.

Study of the various factors influencing deposit formation and operation of gasoline engine injection systems

NASA Astrophysics Data System (ADS)

Stepien, Z.

2016-09-01

Generally, ethanol fuel emits less pollutants than gasoline, it is completely renewable product and has the potential to reduce greenhouse gases emission but, at the same time can present a multitude of technical challenges to engine operation conditions including creation of very adverse engine deposits. These deposits increasing fuel consumption and cause higher exhaust emissions as well as poor performance in drivability. This paper describes results of research and determination the various factors influencing injector deposits build-up of ethanol-gasoline blends operated engine. The relationship between ethanol-gasoline fuel blends composition, their treatment, engine construction as well as its operation conditions and fuel injectors deposit formation has been investigated. Simulation studies of the deposit formation endanger proper functioning of fuel injection system were carried out at dynamometer engine testing. As a result various, important factors influencing the deposit creation process and speed formation were determined. The ability to control of injector deposits by multifunctional detergent-dispersant additives package fit for ethanol-gasoline blends requirements was also investigated.

The Stem Cell Laboratory: Design, Equipment, and Oversight

PubMed Central

Wesselschmidt, Robin L.; Schwartz, Philip H.

2013-01-01

This chapter describes some of the major issues to be considered when setting up a laboratory for the culture of human pluripotent stem cells (hPSCs). The process of establishing a hPSC laboratory can be divided into two equally important parts. One is completely administrative and includes developing protocols, seeking approval, and establishing reporting processes and documentation. The other part of establishing a hPSC laboratory involves the physical plant and includes design, equipment and personnel. Proper planning of laboratory operations and proper design of the physical layout of the stem cell laboratory so that meets the scope of planned operations is a major undertaking, but the time spent upfront will pay long-term returns in operational efficiency and effectiveness. A well-planned, organized, and properly equipped laboratory supports research activities by increasing efficiency and reducing lost time and wasted resources. PMID:21822863

Effectiveness of GNSS disposal strategies

NASA Astrophysics Data System (ADS)

Alessi, E. M.; Rossi, A.; Valsecchi, G. B.; Anselmo, L.; Pardini, C.; Colombo, C.; Lewis, H. G.; Daquin, J.; Deleflie, F.; Vasile, M.; Zuiani, F.; Merz, K.

2014-06-01

The management of the Global Navigation Satellite Systems (GNSS) and of the Medium Earth Orbit (MEO) region as a whole is a subject that cannot be deferred, due to the growing exploitation and launch rate in that orbital regime. The advent of the European Galileo and the Chinese Beidou constellations significantly added complexity to the system and calls for an adequate global view on the four constellations present in operation. The operation procedures, including maintenance and disposal practices, of the constellations currently deployed were analyzed in order to asses a proper reference simulation scenario. The complex dynamics of the MEO region with all the geopotential and lunisolar resonances was studied to better identify the proper end-of-life orbit for every proposed strategy, taking into account and, whenever possible, exploiting the orbital dynamics in this peculiar region of space. The possibility to exploit low thrust propulsion or non gravitational perturbations with passive de-orbiting devices (and a combination of the two) was analyzed, in view of possible applications in the design of the future generations of the constellations satellites. Several upgrades in the long-term evolution software SDM and DAMAGE were undertaken to properly handle the constellation simulations in every aspect from constellation maintenance to orbital dynamics. A thorough approach considering the full time evolving covariance matrix associated with every object was implemented in SDM to compute the collision risk and associated maneuver rate for the constellation satellites. Once the software upgrades will be completed, the effectiveness of the different disposal strategies will be analyzed in terms of residual collision risk and avoidance maneuvers rate. This work was performed under the ESA/GSP Contract no. 4000107201/12/F/MOS.

Economic and kinetic studies of the biological production of farm energy and chemicals from biomass. Annual progress report, March 1979-August 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gaddy, J.L.

1981-08-01

A system has been designed and built to test the technical and economic feasibility of producing farm energy from cellulosic residues. The system has the capacity to produPropinibactriume 1300 CF of biogas and 180 kwh per day, using four parallel batch anaerobic digesters which are agitated mechanically and heated with waste heat from the engine-generator. This system has been satisfactorily operated for a one year period utilizing native grasses as the raw material. Laboratory reactors have been operated to determine the proper inoculation ratio for starting batch cultures with cellulosic raw materials. Procedures for startup and operation of batch digestionmore » systems have been developed and are presented. Energy and economic analyses of the operation of the test unit have been performed. Studies to determine the fertilizer potential of anaerobic digestor sludge (from agricultural residues) have been conducted. Additional studies reported include determinations of the feasibility of separating the stages of anaerobic digestion, the production of acetic and propionic acids by the micro-organism Propionibacterium acidi-propionici, the production of methane from acid hydrolyzates, and the kinetics of the continuos digestion of corn stover.« less

Air traffic management as principled negotiation between intelligent agents

NASA Technical Reports Server (NTRS)

Wangermann, J. P.

1994-01-01

The major challenge facing the world's aircraft/airspace system (AAS) today is the need to provide increased capacity, while reducing delays, increasing the efficiency of flight operations, and improving safety. Technologies are emerging that should improve the performance of the system, but which could also introduce uncertainty, disputes, and inefficiency if not properly implemented. The aim of our research is to apply techniques from intelligent control theory and decision-making theory to define an Intelligent Aircraft/Airspace System (IAAS) for the year 2025. The IAAS would make effective use of the technical capabilities of all parts of the system to meet the demand for increased capacity with improved performance.

Activity and Kinematics of White Dwarf-M Dwarf Binaries from the SUPERBLINK Proper Motion Survey

NASA Astrophysics Data System (ADS)

Skinner, Julie N.; Morgan, Dylan P.; West, Andrew A.; Lépine, Sébastien; Thorstensen, John R.

2017-09-01

We present an activity and kinematic analysis of high proper motion white dwarf-M dwarf binaries (WD+dMs) found in the SUPERBLINK survey, 178 of which are new identifications. To identify WD+dMs, we developed a UV-optical-IR color criterion and conducted a spectroscopic survey to confirm each candidate binary. For the newly identified systems, we fit the two components using model white dwarf spectra and M dwarf template spectra to determine physical parameters. We use Hα chromospheric emission to examine the magnetic activity of the M dwarf in each system, and investigate how its activity is affected by the presence of a white dwarf companion. We find that the fraction of WD+dM binaries with active M dwarfs is significantly higher than their single M dwarf counterparts at early and mid-spectral types. We corroborate previous studies that find high activity fractions at both close and intermediate separations. At more distant separations, the binary fraction appears to approach the activity fraction for single M dwarfs. Using derived radial velocities and the proper motions, we calculate 3D space velocities for the WD+dMs in SUPERBLINK. For the entire SUPERBLINK WD+dMs, we find a large vertical velocity dispersion, indicating a dynamically hotter population compared to high proper motion samples of single M dwarfs. We compare the kinematics for systems with active M dwarfs and those with inactive M dwarfs, and find signatures of asymmetric drift in the inactive sample, indicating that they are drawn from an older population. Based on observations obtained at the MDM Observatory operated by Dartmouth College, Columbia University, The Ohio State University, and the University of Michigan.

Wind farm optimization using evolutionary algorithms

NASA Astrophysics Data System (ADS)

Ituarte-Villarreal, Carlos M.

In recent years, the wind power industry has focused its efforts on solving the Wind Farm Layout Optimization (WFLO) problem. Wind resource assessment is a pivotal step in optimizing the wind-farm design and siting and, in determining whether a project is economically feasible or not. In the present work, three (3) different optimization methods are proposed for the solution of the WFLO: (i) A modified Viral System Algorithm applied to the optimization of the proper location of the components in a wind-farm to maximize the energy output given a stated wind environment of the site. The optimization problem is formulated as the minimization of energy cost per unit produced and applies a penalization for the lack of system reliability. The viral system algorithm utilized in this research solves three (3) well-known problems in the wind-energy literature; (ii) a new multiple objective evolutionary algorithm to obtain optimal placement of wind turbines while considering the power output, cost, and reliability of the system. The algorithm presented is based on evolutionary computation and the objective functions considered are the maximization of power output, the minimization of wind farm cost and the maximization of system reliability. The final solution to this multiple objective problem is presented as a set of Pareto solutions and, (iii) A hybrid viral-based optimization algorithm adapted to find the proper component configuration for a wind farm with the introduction of the universal generating function (UGF) analytical approach to discretize the different operating or mechanical levels of the wind turbines in addition to the various wind speed states. The proposed methodology considers the specific probability functions of the wind resource to describe their proper behaviors to account for the stochastic comportment of the renewable energy components, aiming to increase their power output and the reliability of these systems. The developed heuristic considers a variable number of system components and wind turbines with different operating characteristics and sizes, to have a more heterogeneous model that can deal with changes in the layout and in the power generation requirements over the time. Moreover, the approach evaluates the impact of the wind-wake effect of the wind turbines upon one another to describe and evaluate the power production capacity reduction of the system depending on the layout distribution of the wind turbines.

Advanced deep sea diving equipment

NASA Technical Reports Server (NTRS)

Danesi, W. A.

1972-01-01

Design requirements are generated for a deep sea heavy duty diving system to equip salvage divers with equipment and tools that permit work of the same quality and in times approaching that done on the surface. The system consists of a helmet, a recirculator for removing carbon dioxide, and the diver's dress. The diver controls the inlet flow by the recirculatory control valve and is able to change closed cycle operation to open cycle if malfunction occurs. Proper function of the scrubber in the recirculator minimizes temperature and humidity effects as it filters the returning air.

Fast-acting sprinkler system design considerations for propellant manufacture

NASA Astrophysics Data System (ADS)

Matthews, A. L.; Crable, J. M.; Kristoff, P. T.

1984-08-01

Fast-acting sprinkler systems for detection and suppression of fires in propellant operations, which require activation in the millisecond range in order to be effective, can be easily defeated unless particular attention is paid to design and maintenance details. Of primary consideration are detector selection and placement in processes to minimize the effect of environmental influences. Also important are nozzle placement, water flow density, water supply pressure, and pattern and sloping of piping. When all of these design criteria are properly implemented, water application can occur within 100 ms of fire detection.

76 FR 77128 - Alternate Tonnage Threshold for Oil Spill Response Vessels

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-12

...The Coast Guard is establishing an alternate size threshold based on the measurement system established under the International Convention on Tonnage Measurement of Ships, 1969, for Oil Spill Response Vessels (OSRVs), which are properly certificated under 46 CFR subchapter L. The present size threshold of 500 gross registered tons is based on the U.S. regulatory measurement system. This rule provides an alternative for owners and operators of offshore supply vessels (OSVs) that may result in an increase in oil spill response capacity and capability.

[Time based management in health care system: the chosen aspects].

PubMed

Kobza, Joanna; Syrkiewicz-Świtała, Magdalena

2014-01-01

Time-based management (TBM) is the key element of the whole management process. For many years in health care systems of highly developed countries modern and effective methods of time-based management have been implemented in both primary health care and hospitals (emergency departments and operating rooms). Over the past two decades a systematic review of Polish literature (since 1990) and peer reviewed articles published in international journals based on PubMed/Medline (2001-2011) have been carried out. The collected results indicate that the demographic and health changes in the populations are one of the main challenges facing general practitioners in the nearest future. Time-based management needs new and effective tools and skills, i.e., identification of priorities, well designed planning, delegation of the tasks, proper coordination, and creation of primary care teams that include additional members and human resources management. Proper reimbursement of health services, development of IT in health care system, better collection, storage, processing, analysis and exchange of information and research findings will also be needed. The use of innovative technologies, like telemedicine consultations, provides the possibility of reducing waiting time for diagnosis and treatment and in some cases could be applied in terms of secondary care. To improve the efficiency of operating rooms it is necessary to introduce different solutions, such as operating room coordinator involvement, application of automation to guide decision-making or use of robotic tools to assist surgical procedures. Overcrowded emergency departments have a major detrimental effect on the quality of hospital functions, therefore, efforts should be made to reduce them. Time-based management training among physicians and health care management in Poland, as well as the implementation of practice-based solutions still applied in highly developed countries seem to be necessary.

Master Console System Monitoring and Control Development

NASA Technical Reports Server (NTRS)

Brooks, Russell A.

2013-01-01

The Master Console internship during the summer of 2013 involved the development of firing room displays and support applications at the John F. Kennedy Space Center (KSC). This position was with the Master Console Product Group (MCPG) on the Launch Control System (LCS) project. This project is responsible for the System Monitoring and Control (SMC) and Record and Retrieval (R&R) of launch operations data. The Master Console is responsible for: loading the correct software into each of the remaining consoles in the firing room, connecting the proper data paths to and from the launch vehicle and all ground support equipment, and initializing the entire firing room system to begin processing. During my internship, I created control scripts using the Application Control Language (ACL) to analyze the health and status of Kennedy Ground Control System (KGCS) programmable logic controllers (PLCs). This application provides a system health and status display I created with summarized data for use by Master Console Operators (MCO) to monitor and verify the integrity of KGCS subsystems.

Re-Engineering the Mission Operations System (MOS) for the Prime and Extended Mission

NASA Technical Reports Server (NTRS)

Hunt, Joseph C., Jr.; Cheng, Leo Y.

2012-01-01

One of the most challenging tasks in a space science mission is designing the Mission Operations System (MOS). Whereas the focus of the project is getting the spacecraft built and tested for launch, the mission operations engineers must build a system to carry out the science objectives. The completed MOS design is then formally assessed in the many reviews. Once a mission has completed the reviews, the Mission Operation System (MOS) design has been validated to the Functional Requirements and is ready for operations. The design was built based on heritage processes, new technology, and lessons learned from past experience. Furthermore, our operational concepts must be properly mapped to the mission design and science objectives. However, during the course of implementing the science objective in the operations phase after launch, the MOS experiences an evolutional change to adapt for actual performance characteristics. This drives the re-engineering of the MOS, because the MOS includes the flight and ground segments. Using the Spitzer mission as an example we demonstrate how the MOS design evolved for both the prime and extended mission to enhance the overall efficiency for science return. In our re-engineering process, we ensured that no requirements were violated or mission objectives compromised. In most cases, optimized performance across the MOS, including gains in science return as well as savings in the budget profile was achieved. Finally, we suggest a need to better categorize the Operations Phase (Phase E) in the NASA Life-Cycle Phases of Formulation and Implementation

Implementation of the MPC and A Operations Monitoring (MOM) System at IRT-T FSRE Nuclear Power Institute (NPI)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sitdikov,I.; Zenkov, A.; Tsibulnikov, Y.

The Material Protection, Control and Accounting (MPC&A) Program has been working since 1994 with nuclear sites in Russia to upgrade the physical protection (PP) and material control and accounting (MC&A) functions at facilities containing weapons usable nuclear material. In early 2001, the MPC&A program initiated the MPC&A Operations Monitoring (MOM) Project to monitor facilities where MPC&A upgrades have been installed to provide increased confidence that personnel are present and vigilant, provide confidence that security procedures are being properly performed and provide additional assurance that nuclear materials have not been stolen. The MOM project began as a pilot project at themore » Moscow State Engineering Physics Institute (MEPhI) and a MOM system was successfully installed in October 2001. Following the success of the MEPhI pilot project, the MPC&A Program expanded the installation of MOM systems to several other Russian facilities, including the Nuclear Physics Institute (NPI) in Tomsk. The MOM system was made operational at NPI in October 2004. This paper is focused on the experience gained from operation of this system and the objectives of the MOM system. The paper also describes how the MOM system is used at NPI and, in particular, how the data is analyzed. Finally, potential expansion of the MOM system at NPI is described.« less

Automatic PID Control Loops Design for Performance Improvement of Cryogenic Turboexpander

NASA Astrophysics Data System (ADS)

Joshi, D. M.; Patel, H. K.; Shah, D. K.

2015-04-01

Cryogenics field involves temperature below 123 K which is much less than ambient temperature. In addition, many industrially important physical processes—from fulfilling the needs of National Thermonuclear Fusion programs, superconducting magnets to treatment of cutting tools and preservation of blood cells, require extreme low temperature. The low temperature required for liquefaction of common gases can be obtained by several processes. Liquefaction is the process of cooling or refrigerating a gas to a temperature below its critical temperature so that liquid can be formed at some suitable pressure which is below the critical pressure. Helium liquefier is used for the liquefaction process of helium gas. In general, the Helium Refrigerator/Liquefier (HRL) needs turboexpander as expansion machine to produce cooling effect which is further used for the production of liquid helium. Turboexpanders, a high speed device that is supported on gas bearings, are the most critical component in many helium refrigeration systems. A very minor fault in the operation and manufacturing or impurities in the helium gas can destroy the turboexpander. However, since the performance of expanders is dependent on a number of operating parameters and the relations between them are quite complex, the instrumentation and control system design for turboexpander needs special attention. The inefficiency of manual control leads to the need of designing automatic control loops for turboexpander. Proper design and implementation of the control loops plays an important role in the successful operation of the cryogenic turboexpander. The PID control loops has to be implemented with accurate interlocks and logic to enhance the performance of the cryogenic turboexpander. For different normal and off-normal operations, speeds will be different and hence a proper control method for critical rotational speed avoidance is must. This paper presents the design of PID control loops needed for the efficient performance of cryogenic turboexpander (Radial Inflow type) to ensure that the control systems meet the technical conditions and constraints more accurately and ensure the equipment safety.

Sulfation in lead-acid batteries

NASA Astrophysics Data System (ADS)

Catherino, Henry A.; Feres, Fred F.; Trinidad, Francisco

Virtually, all military land vehicle systems use a lead-acid battery to initiate an engine start. The maintainability of these batteries and as a consequence, system readiness, has suffered from a lack of understanding of the reasons for battery failure. Often, the term most commonly heard for explaining the performance degradation of lead-acid batteries is the word, sulfation. Sulfation is a residual term that came into existence during the early days of lead-acid battery development. The usage is part of the legend that persists as a means for interpreting and justifying the eventual performance deterioration and failure of lead-acid batteries. The usage of this term is confined to the greater user community and, over time, has encouraged a myriad of remedies for solving sulfation problems. One can avoid the connotations associated with the all-inclusive word, sulfation by visualizing the general "sulfation" effect in terms of specific mechanistic models. Also, the mechanistic models are essential for properly understanding the operation and making proper use this battery system. It is evident that the better the model, the better the level of understanding.

Debris/ice/TPS assessment and integrated photographic analysis for Shuttle Mission STS-45

NASA Technical Reports Server (NTRS)

Katnik, Gregory N.; Higginbotham, Scott A.; Davis, J. Bradley

1992-01-01

The Debris Team has developed and implemented measures to control damage from debris in the Shuttle operational environment and to make the control measures a part of routine launch flows. These measures include engineering surveillance during vehicle processing and closeout operations, facility and flight hardware inspections before and after launch, and photographic analysis of mission events. Photographic analyses of mission imagery from launch, on-orbit, and landing provide significant data in verifying proper operation of systems and evaluating anomalies. In addition to the Kennedy Space Center (KSC) Photo/Video Analysis, reports from Johnson Space Center, Marshall Space Flight Center, and Rockwell International-Downey are also included to provide an integrated assessment of each Shuttle mission.

Development of the auto-steering software and equipment technology (ASSET)

NASA Astrophysics Data System (ADS)

McKay, Mark D.; Anderson, Matthew O.; Wadsworth, Derek C.

2003-09-01

The Idaho National Engineering and Environmental Laboratory (INEEL), through collaboration with INSAT Co., has developed a low cost robotic auto-steering system for parallel contour swathing. The capability to perform parallel contour swathing while minimizing "skip" and "overlap" is a necessity for cost-effective crop management within precision agriculture. Current methods for performing parallel contour swathing consist of using a Differential Global Position System (DGPS) coupled with a light bar system to prompt an operator where to steer. The complexity of operating heavy equipment, ensuring proper chemical mixture and application, and steering to a light bar indicator can be overwhelming to an operator. To simplify these tasks, an inexpensive robotic steering system has been developed and tested on several farming implements. This development leveraged research conducted by the INEEL and Utah State University. The INEEL-INSAT Auto-Steering Software and Equipment Technology provides the following: 1) the ability to drive in a straight line within +/- 2 feet while traveling at least 15 mph, 2) interfaces to a Real Time Kinematic (RTK) DGPS and sub-meter DGPS, 3) safety features such as Emergency-stop, steering wheel deactivation, computer watchdog deactivation, etc., and 4) a low-cost, field-ready system that is easily adapted to other systems.

Operations and Maintenance May Newsletter | Poster

Cancer.gov

Occurring without notice, unscheduled utility outages (mainly electrical) are abrupt and create a nuisance. During an unscheduled electrical power outage, the Operations and Maintenance (O&M) department will monitor stand-by generators for proper operation.

40 CFR 60.5130 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... types of emissions. (ii) Basic combustion principles, including products of combustion. (iii) Operation of the specific type of incinerator to be used by the operator, including proper startup, sewage...

40 CFR 60.5130 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... types of emissions. (ii) Basic combustion principles, including products of combustion. (iii) Operation of the specific type of incinerator to be used by the operator, including proper startup, sewage...

Investigation of asphalt content design for open-graded bituminous mixes.

DOT National Transportation Integrated Search

1974-01-01

Several design procedures associated with determining the proper asphalt content for open-graded bituminous mixes were investigated. Also considered was the proper amount of tack coat that should be placed on the old surface prior to paving operation...

49 CFR Appendix E to Part 240 - Recommended Procedures for Conducting Skill Performance Tests

Code of Federal Regulations, 2010 CFR

2010-10-01

... tailor their testing procedures to the specific operational realities. This appendix contains FRA's..., headlight? —Couple to cars at a safe speed? —Properly control in train slack and buff forces? —Properly use...

29 CFR 1926.1416 - Operational aids.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 8 2013-07-01 2013-07-01 false Operational aids. 1926.1416 Section 1926.1416 Labor... Operational aids. (a) The devices listed in this section (“listed operational aids”) are required on all... November 8, 2011. (b) Operations must not begin unless the listed operational aids are in proper working...

29 CFR 1926.1416 - Operational aids.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 8 2012-07-01 2012-07-01 false Operational aids. 1926.1416 Section 1926.1416 Labor... Operational aids. (a) The devices listed in this section (“listed operational aids”) are required on all... November 8, 2011. (b) Operations must not begin unless the listed operational aids are in proper working...

29 CFR 1926.1416 - Operational aids.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 8 2014-07-01 2014-07-01 false Operational aids. 1926.1416 Section 1926.1416 Labor... Operational aids. (a) The devices listed in this section (“listed operational aids”) are required on all... November 8, 2011. (b) Operations must not begin unless the listed operational aids are in proper working...

Discharge measurements using a broad-band acoustic Doppler current profiler

USGS Publications Warehouse

Simpson, Michael R.

2002-01-01

The measurement of unsteady or tidally affected flow has been a problem faced by hydrologists for many years. Dynamic discharge conditions impose an unreasonably short time constraint on conventional current-meter discharge-measurement methods, which typically last a minimum of 1 hour. Tidally affected discharge can change more than 100 percent during a 10-minute period. Over the years, the U.S. Geological Survey (USGS) has developed moving-boat discharge-measurement techniques that are much faster but less accurate than conventional methods. For a bibliography of conventional moving-boat publications, see Simpson and Oltmann (1993, page 17). The advent of the acoustic Doppler current profiler (ADCP) made possible the development of a discharge-measurement system capable of more accurately measuring unsteady or tidally affected flow. In most cases, an ADCP discharge-measurement system is dramatically faster than conventional discharge-measurement systems, and has comparable or better accuracy. In many cases, an ADCP discharge-measurement system is the only choice for use at a particular measurement site. ADCP systems are not yet ?turnkey;? they are still under development, and for proper operation, require a significant amount of operator training. Not only must the operator have a rudimentary knowledge of acoustic physics, but also a working knowledge of ADCP operation, the manufacturer's discharge-measurement software, and boating techniques and safety.

Analysis of integrated photovoltaic-thermal systems using solar concentrators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yusoff, M.B.

1983-01-01

An integrated photovoltaic-thermal system using solar concentrators utilizes the solar radiation spectrum in the production of electrical and thermal energy. The electrical conversion efficiency of this system decreases with increasing solar cell temperature. Since a high operating temperature is desirable to maximize the quality of thermal output of the planned integrated system, a proper choice of the operating temperature for the unit cell is of vital importance. The analysis predicts performance characteristics of the unit cell by considering the dependence of the heat generation, the heat absorption and the heat transmission on the material properties of the unit cell structure.more » An analytical model has been developed to describe the heat transport phenomena occurring in the unit cell structure. The range of applicability of the one-dimensional and the two-dimensional models, which have closed-form solutions, has been demonstrated. Parametric and design studies point out the requirements for necessary good electrical and thermal performance. A procedure utilizing functional forms of component characteristics in the form of partial coefficients of the dependent variable has been developed to design and operate the integrated system to have a desirable value of the thermal to electrical output ratio both at design and operating modes.« less

Methane Recovery from Animal Manures The Current Opportunities Casebook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lusk, P.

1998-09-22

Growth and concentration of the livestock industry create opportunities for the proper disposal of the large quantities of manures generated at dairy, swine, and poultry farms. Pollutants from unmanaged livestock wastes can degrade the environment, and methane emitted from decomposing manure may contribute to global climate change. One management system not only helps prevent pollution but can also convert a manure problem into a new profit center. Economic evaluations and case studies of operating systems indicate that the anaerobic digestion of livestock manures is a commercially viable conversion technology with considerable potential for providing profitable coproducts, including a cost-effective renewablemore » fuel for livestock production operations. This casebook examines some of the current opportunities for recovering methane from anaerobic digestion animal manures.« less

Overview of NASA Lewis Research Center free-piston Stirling engine technology activities applicable to space power systems

NASA Technical Reports Server (NTRS)

Slaby, Jack G.

1987-01-01

A brief overview is presented of the development and technological activities of the free-piston Stirling engine. The engine started as a small scale fractional horsepower engine which demonstrated basic engine operating principles and the advantages of being hermetically sealed, highly efficient, and simple. It eventually developed into the free piston Stirling engine driven heat pump, and then into the SP-100 Space Reactor Power Program from which came the Space Power Demonstrator Engine (SPDE). The SPDE successfully operated for over 300 hr and delivered 20 kW of PV power to an alternator plunger. The SPDE demonstrated that a dynamic power conversion system can, with proper design, be balanced; and the engine performed well with externally pumped hydrostatic gas bearings.

Hamiltonian purification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Orsucci, Davide; Burgarth, Daniel; Facchi, Paolo

The problem of Hamiltonian purification introduced by Burgarth et al. [Nat. Commun. 5, 5173 (2014)] is formalized and discussed. Specifically, given a set of non-commuting Hamiltonians (h{sub 1}, …, h{sub m}) operating on a d-dimensional quantum system ℋ{sub d}, the problem consists in identifying a set of commuting Hamiltonians (H{sub 1}, …, H{sub m}) operating on a larger d{sub E}-dimensional system ℋ{sub d{sub E}} which embeds ℋ{sub d} as a proper subspace, such that h{sub j} = PH{sub j}P with P being the projection which allows one to recover ℋ{sub d} from ℋ{sub d{sub E}}. The notions of spanning-set purificationmore » and generator purification of an algebra are also introduced and optimal solutions for u(d) are provided.« less

User-driven integrated software lives: ``Paleomag'' paleomagnetics analysis on the Macintosh

NASA Astrophysics Data System (ADS)

Jones, Craig H.

2002-12-01

"PaleoMag," a paleomagnetics analysis package originally developed for the Macintosh operating system in 1988, allows examination of demagnetization of individual samples and analysis of directional data from collections of samples. Prior to recent reinvigorated development of the software for both Macintosh and Windows, it was widely used despite not running properly on machines and operating systems sold after 1995. This somewhat surprising situation demonstrates that there is a continued need for integrated analysis software within the earth sciences, in addition to well-developed scripting and batch-mode software. One distinct advantage of software like PaleoMag is in the ability to combine quality control with analysis within a unique graphical environment. Because such demands are frequent within the earth sciences, means of nurturing the development of similar software should be found.

Infrared Chemiluminescence Studies of Ion-Molecule Reactions in a Flowing Afterglow.

DTIC Science & Technology

1982-01-01

reaction rate constants and branching ratios have been addressed in drift tubes and flow drift systems, and the translational energy distribution of atomic...composed of about 40 thin cylindrical sections of flow tube , separated by mylar spacers and connected by precision resistors. In the region of LIF... tube radius (Albritton, 1967). For proper operation of a drift tube , ionic species of only one polarity can be present. Efficient separation of

Benthic Flux Sampling Device. Operations, Methods, and Procedures

DTIC Science & Technology

1993-02-01

nitric acid (HNO3) overnight, then rinse with D.I. water. When in doubt, consult with the chemist for proper cleaning protocols. CHARGE BATTERIES...sis being performed. The system will be flushed with methanol to remove organic com- pounds and with nitric acid to remove metals. The nitric acid ... acid -washed, 500-me Teflon (TFE) sampling bottles aboard the BFSD. After each deployment, blank ferrules are fitted in place of the sampling lines and

Modelling Tradeoffs Evolution in Multipurpose Water Systems Operation in Response to Extreme Events

NASA Astrophysics Data System (ADS)

Mason, E.; Gazzotti, P.; Amigoni, F.; Giuliani, M.; Castelletti, A.

2015-12-01

Multipurpose water resource systems are usually operated on a tradeoff of the operating objectives, which - under steady state climatic and socio-economic boundary conditions - is supposed to ensure a fair and/or efficient balance among the conflicting interests. Extreme variability in the system's drivers might affect operators' risk aversion and force a change in the tradeoff. Properly accounting for these shifts is key to any rigorous retrospective assessment of operators' behavior and the associated system's performance. In this study, we explore how the selection of different optimal tradeoffs among the operating objectives is linked to the variations of the boundary conditions, such as, for example, drifting rainfall season or remarkable changes in crop and energy prices. We argue that tradeoff selection is driven by recent, extreme variations in system performance: underperforming on one of the operating objective target value should push the tradeoff toward the disadvantaged objective. To test this assumption, we developed a rational procedure to simulate the operators' tradeoff selection process. We map the selection onto a multi lateral negotiation process, where different multiple, virtual agents optimize different operating objectives. The agents periodically negotiate a compromise on the operating policy. The agent's rigidity in each negotiation round is determined by the recent system performances according to the specific objective it represents. The negotiation follows a set-based egocentric monotonic concession protocol: at each negotiation step an agent incrementally adds some options to the set of its acceptable compromises and (possibly) accepts lower and lower satisfying policies until an agreement is achieved. We apply this reiterated negotiation framework on the regulated Lake Como, Italy, simulating the lake dam operation and its recurrent updates over the last 50 years. The operation aims to balance shoreline flood prevention and irrigation deficit control in the downstream irrigated areas. The results of our simulated negotiations are able to accurately capture the operator's risk aversion changes as driven by extreme wet and dry situations, and to well reproduce the observational release data.

A New Control System Software for SANS BATAN Spectrometer in Serpong, Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bharoto; Putra, Edy Giri Rachman

2010-06-22

The original main control system of the 36 meter small-angle neutron scattering (SANS) BATAN Spectrometer (SMARTer) has been replaced with the new ones due to the malfunction of the main computer. For that reason, a new control system software for handling all the control systems was also developed in order to put the spectrometer back in operation. The developed software is able to control the system such as rotation movement of six pinholes system, vertical movement of four neutron guide system with the total length of 16.5 m, two-directional movement of a neutron beam stopper, forward-backward movement of a 2Dmore » position sensitive detector (2D-PSD) along 16.7 m, etc. A Visual Basic language program running on Windows operating system was employed to develop the software and it can be operated by other remote computers in the local area network. All device positions and command menu are displayed graphically in the main monitor or window and each device control can be executed by clicking the control button. Those advantages are necessary required for developing a new user-friendly control system software. Finally, the new software has been tested for handling a complete SANS experiment and it works properly.« less

A New Control System Software for SANS BATAN Spectrometer in Serpong, Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bharoto,; Putra, Edy Giri Rachman

2010-06-22

The original main control system of the 36 meter small‐angle neutron scattering (SANS) BATAN Spectrometer (SMARTer) has been replaced with the new ones due to the malfunction of the main computer. For that reason, a new control system software for handling all the control systems was also developed in order to put the spectrometer back in operation. The developed software is able to control the system such as rotation movement of six pinholes system, vertical movement of four neutron guide system with the total length of 16.5 m, two‐directional movement of a neutron beam stopper, forward‐backward movement of a 2Dmore » position sensitive detector (2D‐PSD) along 16.7 m, etc. A Visual Basic language program running on Windows operating system was employed to develop the software and it can be operated by other remote computers in the local area network. All device positions and command menu are displayed graphically in the main monitor or window and each device control can be executed by clicking the control button. Those advantages are necessary required for developing a new user‐friendly control system software. Finally, the new software has been tested for handling a complete SANS experiment and it works properly.« less

Control of Smart Building Using Advanced SCADA

NASA Astrophysics Data System (ADS)

Samuel, Vivin Thomas

For complete control of the building, a proper SCADA implementation and the optimization strategy has to be build. For better communication and efficiency a proper channel between the Communication protocol and SCADA has to be designed. This paper concentrate mainly between the communication protocol, and the SCADA implementation, for a better optimization and energy savings is derived to large scale industrial buildings. The communication channel used in order to completely control the building remotely from a distant place. For an efficient result we consider the temperature values and the power ratings of the equipment so that while controlling the equipment, we are setting a threshold values for FDD technique implementation. Building management system became a vital source for any building to maintain it and for safety purpose. Smart buildings, refers to various distinct features, where the complete automation system, office building controls, data center controls. ELC's are used to communicate the load values of the building to the remote server from a far location with the help of an Ethernet communication channel. Based on the demand fluctuation and the peak voltage, the loads operate differently increasing the consumption rate thus results in the increase in the annual consumption bill. In modern days, saving energy and reducing the consumption bill is most essential for any building for a better and long operation. The equipment - monitored regularly and optimization strategy is implemented for cost reduction automation system. Thus results in the reduction of annual cost reduction and load lifetime increase.

Use of a pitch adjustable foot restraint system: Operator strength capability and load requirements

NASA Technical Reports Server (NTRS)

Wilmington, Robert P.; Poliner, Jeffrey; Klute, Glenn K.

1994-01-01

The zero-gravity environment creates a need for a proper human body restraint system to maintain a comfortable posture with less fatigue and to maximize productivity. In addition, restraint systems must be able to meet the loading demands of maintenance and assembly tasks performed on orbit. The shuttle's primary intravehicular astronaut restraint system is currently a foot loop design that attaches to flat surfaces on the shuttle, allowing for varying mounting locations and easy egress and ingress. However, this design does not allow for elevation, pitch, or foot loop length adjustment. Several prototype foot restraint systems are being evaluated for use aboard the space station and the space shuttle. The JSC Anthropometry and Biomechanics Laboratory initiated this study to quantify the maximum axial forces and moments that would be induced on a foot loop type of restraint while operators performed a torque wrench task, also allowing for angling the restraint pitch angle to study yet another effect. Results indicate that the greatest forces into the torque wrench and into the foot restraint system occur while the operator performs an upward effort. This study did not see any significant difference in the operators' force due to pitch orientation. Thus, in a work environment in which hand holds are available, no significant influence of the pitch angle on forces imparted to the restraint system existed.

Probabilistic risk assessment of the Space Shuttle. Phase 3: A study of the potential of losing the vehicle during nominal operation. Volume 2: Integrated loss of vehicle model

NASA Technical Reports Server (NTRS)

Fragola, Joseph R.; Maggio, Gaspare; Frank, Michael V.; Gerez, Luis; Mcfadden, Richard H.; Collins, Erin P.; Ballesio, Jorge; Appignani, Peter L.; Karns, James J.

1995-01-01

The application of the probabilistic risk assessment methodology to a Space Shuttle environment, particularly to the potential of losing the Shuttle during nominal operation is addressed. The different related concerns are identified and combined to determine overall program risks. A fault tree model is used to allocate system probabilities to the subsystem level. The loss of the vehicle due to failure to contain energetic gas and debris, to maintain proper propulsion and configuration is analyzed, along with the loss due to Orbiter, external tank failure, and landing failure or error.

Potential of minicomputer/array-processor system for nonlinear finite-element analysis

NASA Technical Reports Server (NTRS)

Strohkorb, G. A.; Noor, A. K.

1983-01-01

The potential of using a minicomputer/array-processor system for the efficient solution of large-scale, nonlinear, finite-element problems is studied. A Prime 750 is used as the host computer, and a software simulator residing on the Prime is employed to assess the performance of the Floating Point Systems AP-120B array processor. Major hardware characteristics of the system such as virtual memory and parallel and pipeline processing are reviewed, and the interplay between various hardware components is examined. Effective use of the minicomputer/array-processor system for nonlinear analysis requires the following: (1) proper selection of the computational procedure and the capability to vectorize the numerical algorithms; (2) reduction of input-output operations; and (3) overlapping host and array-processor operations. A detailed discussion is given of techniques to accomplish each of these tasks. Two benchmark problems with 1715 and 3230 degrees of freedom, respectively, are selected to measure the anticipated gain in speed obtained by using the proposed algorithms on the array processor.

Locating underwater objects. [technology transfer

NASA Technical Reports Server (NTRS)

Grice, C. F.

1974-01-01

Underwater search operations are considered to be engineering and operational problems. A process for proper definition of the problem and selection of instrumentation and operational procedures is described. An outline of underwater search instrumentation and techniques is given.

40 CFR 62.14595 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

..., including types of emissions. (ii) Basic combustion principles, including products of combustion. (iii) Operation of the specific type of incinerator to be used by the operator, including proper startup, waste...

Analysis of a flux-coupling type superconductor fault current limiter with pancake coils

NASA Astrophysics Data System (ADS)

Liu, Shizhuo; Xia, Dong; Zhang, Zhifeng; Qiu, Qingquan; Zhang, Guomin

2017-10-01

The characteristics of a flux-coupling type superconductor fault current limiter (SFCL) with pancake coils are investigated in this paper. The conventional double-wound non-inductive pancake coil used in AC power systems has an inevitable defect in Voltage Sourced Converter Based High Voltage DC (VSC-HVDC) power systems. Due to its special structure, flashover would occur easily during the fault in high voltage environment. Considering the shortcomings of conventional resistive SFCLs with non-inductive coils, a novel flux-coupling type SFCL with pancake coils is carried out. The module connections of pancake coils are performed. The electromagnetic field and force analysis of the module are contrasted under different parameters. To ensure proper operation of the module, the impedance of the module under representative operating conditions is calculated. Finally, the feasibility of the flux-coupling type SFCL in VSC-HVDC power systems is discussed.

Development of an automated potable water bactericide monitoring unit

NASA Technical Reports Server (NTRS)

Walsh, J. M.; Brawner, C. C.; Sauer, R. L.

1975-01-01

A monitor unit has been developed that permits the direct determination of the level of elemental iodine, used for microbiological control, in a spacecraft potable water supply system. Salient features of unit include low weight, volume and maintenance requirements, complete automatic operation, no inflight calibration, no expendables (except electrical current) and high accuracy and precision. This unit is capable of providing a signal to a controller that, in turn, automatically adjusts the addition rate of iodine to the potable water system so that a predetermined level of iodine can be maintained. In addition, the monitor provides a reading whereby the crewman can verify that the proper amount of iodine (within a range) is present in the water. A development history of the monitor is presented along with its design and theory of operation. Also presented are the results generated through testing of the unit in a simulated Shuttle potable water system.

Performance monitoring can boost turboexpander efficiency

DOE Office of Scientific and Technical Information (OSTI.GOV)

McIntire, R.

1982-07-05

This paper discusses ways of improving the productivity of the turboexpander/refrigeration system's radial expander and radial compressor through systematic review of component performance. It reviews several techniques to determine the performance of an expander and compressor. It suggests that any performance improvement program requires quantifying the performance of separate components over a range of operating conditions; estimating the increase in performance associated with any hardware change; and developing an analytical (computer) model of the entire system by using the performance curve of individual components. The model is used to quantify the economic benefits of any change in the system, eithermore » a change in operating procedures or a hardware modification. Topics include proper ways of using antisurge control valves and modifying flow rate/shaft speed (Q/N). It is noted that compressor efficiency depends on the incidence angle of blade at the rotor leading edge and the angle of the incoming gas stream.« less

Superfund Record of Decision (EPA Region 5): Spickler Landfill, Operable Unit 2, Spencer, WI, September 29, 1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This decision document represents the selected remedial action for Operable Unit (OU) No. 2 at the Spickler Landfill Superfund Site (the Site) in Specer, Wisconsin. The United States Environmental Protection Agency (US EPA) has found that no further action is appropriate due to the effectiveness of the remedial action for the first operable unit. Proper closure of the landfills and mercury brine pit, installation of a landfill gas collection and flare and leachate collection systems and continued operation have eliminated the primary human health risk posed by direct contact with contaminated soils, eliminated the threat to the environment, and mitigatedmore » the primary human health risk posed by contaminated Site groundwater and landfill gas. The remedy established by this ROD is the final Remedial Action for this Site.« less

Studies of The Durability of Belt Conveyor Idlers with Working Loads Taken into Account

NASA Astrophysics Data System (ADS)

Król, Robert

2017-12-01

The results of laboratory and operational studies conducted in the Machinery Systems Division of Wroclaw University of Technology in recent years have became the basis for selecting proper belt conveyor roller designs optimized for specific strength and operational criteria. The usefulness of the results for assessing the energy intensity of idlers, estimating their durability and determining modernization policies has been confirmed. Methods of estimating the durability of carrying idlers on the basis of the identified output stream distributions are presented. Results of studies carried out using an analytical method and a laboratory method are reported. It has been shown that the operational durability of a roller is determined by its design, the roller set parameters (the spacing and the angle of bevel) and the operating conditions having a bearing on the irregularity of the transported output stream.

How does information congruence influence diagnosis performance?

PubMed

Chen, Kejin; Li, Zhizhong

2015-01-01

Diagnosis performance is critical for the safety of high-consequence industrial systems. It depends highly on the information provided, perceived, interpreted and integrated by operators. This article examines the influence of information congruence (congruent information vs. conflicting information vs. missing information) and its interaction with time pressure (high vs. low) on diagnosis performance on a simulated platform. The experimental results reveal that the participants confronted with conflicting information spent significantly more time generating correct hypotheses and rated the results with lower probability values than when confronted with the other two levels of information congruence and were more prone to arrive at a wrong diagnosis result than when they were provided with congruent information. This finding stresses the importance of the proper processing of non-congruent information in safety-critical systems. Time pressure significantly influenced display switching frequency and completion time. This result indicates the decisive role of time pressure. Practitioner Summary: This article examines the influence of information congruence and its interaction with time pressure on human diagnosis performance on a simulated platform. For complex systems in the process control industry, the results stress the importance of the proper processing of non-congruent information in safety-critical systems.

Preliminary Recommendations for the Collection, Storage, and Analysis of UAS Safety Data

NASA Technical Reports Server (NTRS)

Enomoto, Francis; Bushnell, David; Denney, Ewen; Pai, Ganesh; Schumann, Johann

2013-01-01

Although the use of UASs in military and public service operations is proliferating, civilian use of UASs remains limited in the United States today. With efforts underway to accommodate and integrate UASs into the NAS, a proactive understanding of safety issues, i.e., the unique hazards and the corresponding risks that UASs pose not only through their operations for commercial purposes, but also to existing operations in the NAS, is especially important so as to (a) support the development of a sound regulatory basis, (b) regulate, design and properly equip UASs, and (c) effectively mitigate the risks posed. Data, especially about system and component failures, incidents, and accidents, provides valuable insight into how performance and operational capabilities/limitations contribute to hazards. Since the majority of UAS operations today take place in a context that is significantly different from the norm in civil aviation, i.e., with different operational goals and standards, identifying that which constitutes useful and sufficient data on UASs and their operations is a substantial research challenge.

Improved polar display technique of the phase angle of optical interference

NASA Astrophysics Data System (ADS)

Umeda, N.; Shirai, H.; Takasaki, H.

1984-02-01

A technique which displays the fractional order of optical interference by the azimuthal angle of radial arm has been improved by using a digital electronic circuit such as phase-locked loop and D flip-flop. The phase quadrature reference signals of this system are derived by reforming a reference signal and shifting it by a quarter wavelength referring to its waveform. As the result the orthogonal phase relation of the two signals is not affected by the frequency of the signal. This system has been proven to operate properly over the frequency range of 200-600 kHz without readjusting the electric system.

In-service communication channel sensing based on reflectometry for TWDM-PON systems

NASA Astrophysics Data System (ADS)

Iida, Daisuke; Kuwano, Shigeru; Terada, Jun

2014-05-01

Many base stations are accommodated in TWDM-PON based mobile backhaul and fronthaul networks for future radio access, and failed connections in an optical network unit (ONU) wavelength channel severely degrade system performance. A cost effective in-service ONU wavelength channel monitor is essential to ensure proper system operation without failed connections. To address this issue we propose a reflectometry-based remote sensing method that provides wavelength channel information with the optical line terminal (OLT)-ONU distance. The method realizes real-time monitoring of ONU wavelength channels without signal quality degradation. Experimental results show it achieves wavelength channel distinction with high distance resolution.

Apparatus for inspecting piping

DOEpatents

Zollingger, W. Thor; Appel, D. Keith; Park, Larry R.

1995-01-01

An inspection rabbit for inspecting piping systems having severe bends therein. The rabbit consists of a flexible, modular body containing a miniaturized eddy current inspection probe, a self-contained power supply for proper operation of the rabbit, an outer surface that allows ease of movement through piping systems and means for transmitting data generated by the inspection device. The body is preferably made of flexible polyvinyl chloride (PVC) tubing or, alternatively, silicone rubber with a shrink wrapping of polytetrafluoroethylene (TEFLON.RTM.). The body is formed to contain the power supply, preferably a plurality of batteries, and a spool of communication wire that connects to a data processing computer external to the piping system.

Application-Program-Installer Builder

NASA Technical Reports Server (NTRS)

Wolgast, Paul; Demore, Martha; Lowik, Paul

2007-01-01

A computer program builds application programming interfaces (APIs) and related software components for installing and uninstalling application programs in any of a variety of computers and operating systems that support the Java programming language in its binary form. This program is partly similar in function to commercial (e.g., Install-Shield) software. This program is intended to enable satisfaction of a quasi-industry-standard set of requirements for a set of APIs that would enable such installation and uninstallation and that would avoid the pitfalls that are commonly encountered during installation of software. The requirements include the following: 1) Properly detecting prerequisites to an application program before performing the installation; 2) Properly registering component requirements; 3) Correctly measuring the required hard-disk space, including accounting for prerequisite components that have already been installed; and 4) Correctly uninstalling an application program. Correct uninstallation includes (1) detecting whether any component of the program to be removed is required by another program, (2) not removing that component, and (3) deleting references to requirements of the to-be-removed program for components of other programs so that those components can be properly removed at a later time.

Repair, Evaluation, Maintenance, and Rehabilitation Research Program. Lubricants for Hydraulic Structures

DTIC Science & Technology

1989-08-01

machinery design , precision machining, proper maintenance, and proper lubrication. Ordinarily, wear is thought of only in terms of abrasive wear occurring in...operate under this principle. However, the design must allow the plates to lift and tilt properly and provide sufficient area to lift the load. 38. Another...friction and wear to a minimum. Boundary Lubrication 42. Lubrication designed to protect against frictional effects when asperities meet is called

Techniques for Interventional MRI Guidance in Closed-Bore Systems.

PubMed

Busse, Harald; Kahn, Thomas; Moche, Michael

2018-02-01

Efficient image guidance is the basis for minimally invasive interventions. In comparison with X-ray, computed tomography (CT), or ultrasound imaging, magnetic resonance imaging (MRI) provides the best soft tissue contrast without ionizing radiation and is therefore predestined for procedural control. But MRI is also characterized by spatial constraints, electromagnetic interactions, long imaging times, and resulting workflow issues. Although many technical requirements have been met over the years-most notably magnetic resonance (MR) compatibility of tools, interventional pulse sequences, and powerful processing hardware and software-there is still a large variety of stand-alone devices and systems for specific procedures only.Stereotactic guidance with the table outside the magnet is common and relies on proper registration of the guiding grids or manipulators to the MR images. Instrument tracking, often by optical sensing, can be added to provide the physicians with proper eye-hand coordination during their navigated approach. Only in very short wide-bore systems, needles can be advanced at the extended arm under near real-time imaging. In standard magnets, control and workflow may be improved by remote operation using robotic or manual driving elements.This work highlights a number of devices and techniques for different interventional settings with a focus on percutaneous, interstitial procedures in different organ regions. The goal is to identify technical and procedural elements that might be relevant for interventional guidance in a broader context, independent of the clinical application given here. Key challenges remain the seamless integration into the interventional workflow, safe clinical translation, and proper cost effectiveness.

Tune-Up Your Fan Systems for Improved Performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fans are used extensively in commercial buildings and represent approximately 6% of total energy consumed by commercial buildings. The U.S. Department of Energy (DOE) estimates that fans in commercial buildings consume 158 billion kWh of electricity annually. Maintaining fan systems in proper condition provides energy savings and ensures a comfortable and healthy environment. While many fan systems have significant energy savings opportunities available through improvements in fan selection, system design, and operational practices, it is not always apparent when a fan system needs maintenance or what opportunities are available for improvements. This resource is designed for facility managers and maintenancemore » staff to provide easy-to-implement actionable guidance on fan efficiency measures for existing ducted air systems.« less

Image-guided positioning and tracking.

PubMed

Ruan, Dan; Kupelian, Patrick; Low, Daniel A

2011-01-01

Radiation therapy aims at maximizing tumor control while minimizing normal tissue complication. The introduction of stereotactic treatment explores the volume effect and achieves dose escalation to tumor target with small margins. The use of ablative irradiation dose and sharp dose gradients requires accurate tumor definition and alignment between patient and treatment geometry. Patient geometry variation during treatment may significantly compromise the conformality of delivered dose and must be managed properly. Setup error and interfraction/intrafraction motion are incorporated in the target definition process by expanding the clinical target volume to planning target volume, whereas the alignment between patient and treatment geometry is obtained with an adaptive control process, by taking immediate actions in response to closely monitored patient geometry. This article focuses on the monitoring and adaptive response aspect of the problem. The term "image" in "image guidance" will be used in a most general sense, to be inclusive of some important point-based monitoring systems that can be considered as degenerate cases of imaging. Image-guided motion adaptive control, as a comprehensive system, involves a hierarchy of decisions, each of which balances simplicity versus flexibility and accuracy versus robustness. Patient specifics and machine specifics at the treatment facility also need to be incorporated into the decision-making process. Identifying operation bottlenecks from a system perspective and making informed compromises are crucial in the proper selection of image-guidance modality, the motion management mechanism, and the respective operation modes. Not intended as an exhaustive exposition, this article focuses on discussing the major issues and development principles for image-guided motion management systems. We hope these information and methodologies will facilitate conscientious practitioners to adopt image-guided motion management systems accounting for patient and institute specifics and to embrace advances in knowledge and new technologies subsequent to the publication of this article.

The development of a microprocessor-controlled linearly-actuated valve assembly

NASA Technical Reports Server (NTRS)

Wall, R. H.

1984-01-01

The development of a proportional fluid control valve assembly is presented. This electromechanical system is needed for space applications to replace the current proportional flow controllers. The flow is controlled by a microprocessor system that monitors the control parameters of upstream pressure and requested volumetric flow rate. The microprocessor achieves the proper valve stem displacement by means of a digital linear actuator. A linear displacement sensor is used to measure the valve stem position. This displacement is monitored by the microprocessor system as a feedback signal to close the control loop. With an upstream pressure between 15 and 47 psig, the developed system operates between 779 standard CU cm/sec (SCCS) and 1543 SCCS.

Achieving the Proper Balance Between Crew and Public Safety

NASA Technical Reports Server (NTRS)

Gowan, John; Silvestri, Ray; Stahl, Ben; Rosati, Paul; Wilde, Paul

2011-01-01

A paramount objective of all human-rated launch and reentry vehicle developers is to ensure that the risks to both the crew onboard and the public are minimized within reasonable cost, schedule, and technical constraints. Past experience has shown that proper attention to range safety requirements necessary to ensure public safety must be given early in the design phase to avoid additional operational complexities or threats to the safety of people onboard, and the design engineers must give these requirements the same consideration as crew safety requirements. For human spaceflight, the primary purpose and operational concept for any flight safety system is to protect the public while maximizing the likelihood of crew survival. This paper will outline the policy considerations, technical issues, and operational impacts regarding launch and reentry vehicle failure scenarios where crew and public safety are intertwined and thus addressed optimally in an integrated manner. An overview of existing range and crew safety policy requirements will be presented. Application of these requirements and lessons learned from both the Space Shuttle and Constellation Programs will also be discussed. Using these past programs as examples, the paper will detail operational, design, and analysis approaches to mitigate and balance the risks to people onboard and in the public. Manned vehicle perspectives from the Federal Aviation Administration (FAA) and Air Force organizations that oversee public safety will be summarized as well. Finally, the paper will emphasize the need to factor policy, operational, and analysis considerations into the early design trades of new vehicles to help ensure that both crew and public safety are maximized to the greatest extent possible.

Achieving the Proper Balance between Crew & Public Safety

NASA Astrophysics Data System (ADS)

Wilde, P.; Gowan, J.; Silvestri, R.; Stahl, B.; Rosati, P.

2012-01-01

A paramount objective of all human-rated launch and reentry vehicle developers is to ensure that the risks to both the crew onboard and the public are minimized within reasonable cost, schedule, and technical constraints. Past experience has shown that proper attention to range safety requirements necessary to ensure public safety must be given early in the design phase to avoid additional operational complexities or threats to the safety of people onboard, and the design engineers must give these requirements the same consideration as crew safety requirements. For human spaceflight, the primary purpose and operational concept for any flight safety system is to protect the public while maximizing the likelihood of crew survival. This paper will outline the policy considerations, technical issues, and operational impacts regarding launch and reentry vehicle failure scenarios where crew and public safety are intertwined and thus addressed optimally in an integrated manner. An overview of existing range and crew safety policy requirements will be presented. Application of these requirements and lessons learned from both the Space Shuttle and Constellation Programs will also be discussed. Using these past programs as examples, the paper will detail operational, design, and analysis approaches to mitigate and balance the risks to people onboard and in the public. Crewed vehicle perspectives from the Federal Aviation Administration and Air Force organizations that oversee public safety will be summarized as well. Finally, the paper will emphasize the need to factor policy, operational, and analysis considerations into the early design trades of new vehicles to help ensure that both crew and public safety are maximized to the greatest extent possible.

Photovoltaic-Powered Vaccine Refrigerator: Freezer Systems Field Test Results

NASA Technical Reports Server (NTRS)

Ratajczak, A. F.

1985-01-01

A project to develop and field test photovoltaic-powered refrigerator/freezers suitable for vaccine storage was undertaken. Three refrigerator/freezers were qualified; one by Solar Power Corp. and two by Solvolt. Follow-on contracts were awarded for 19 field test systems and for 10 field test systems. A total of 29 systems were installed in 24 countries between October 1981 and October 1984. The project, systems descriptions, installation experiences, performance data for the 22 systems for which field test data was reported, an operational reliability summary, and recommendations relative to system designs and future use of such systems are explained. Performance data indicate that the systems are highly reliable and are capable of maintaining proper vaccine storage temperatures in a wide range of climatological and user environments.

A web-based solution to visualize operational monitoring data in the Trigger and Data Acquisition system of the ATLAS experiment at the LHC

NASA Astrophysics Data System (ADS)

Avolio, G.; D'Ascanio, M.; Lehmann-Miotto, G.; Soloviev, I.

2017-10-01

The Trigger and Data Acquisition (TDAQ) system of the ATLAS detector at the Large Hadron Collider at CERN is composed of a large number of distributed hardware and software components (about 3000 computers and more than 25000 applications) which, in a coordinated manner, provide the data-taking functionality of the overall system. During data taking runs, a huge flow of operational data is produced in order to constantly monitor the system and allow proper detection of anomalies or misbehaviours. In the ATLAS trigger and data acquisition system, operational data are archived and made available to applications by the P-BEAST (Persistent Back-End for the Atlas Information System of TDAQ) service, implementing a custom time-series database. The possibility to efficiently visualize both realtime and historical operational data is a great asset facilitating both online identification of problems and post-mortem analysis. This paper will present a web-based solution developed to achieve such a goal: the solution leverages the flexibility of the P-BEAST archiver to retrieve data, and exploits the versatility of the Grafana dashboard builder to offer a very rich user experience. Additionally, particular attention will be given to the way some technical challenges (like the efficient visualization of a huge amount of data and the integration of the P-BEAST data source in Grafana) have been faced and solved.

Vacuum ultraviolet radiation and thermal cycling effects on atomic oxygen protective photovoltaic array blanket materials

NASA Technical Reports Server (NTRS)

Brady, J.; Banks, B.

1990-01-01

The importance of synergistic environmental exposure is demonstrated through the evaluation of DuPont 93-1 in simulated LEO environment. Changes in optical properties, surface condition, and mass loss data are described. The qualitative results indicate the necessity for exposure of materials to a series of simulated LEO environments in order to properly determine synergistic effects and demonstrate the overall LEO durability of candidate materials. It is shown that synergistic effects may occur with vacuum thermal cycling combined with VUV radiation followed by atomic oxygen exposure. Testing the durability of candidate solar array blanket materials in a test sequence with necessary synergistic effects makes it possible to determine the appropriate material for providing structural support and maintaining the proper operating temperature for solar cells in the SSF Photovaltaic Power System.

Organizational Systems Theory and Command and Control Concepts

DTIC Science & Technology

2013-03-01

Decentralized C2 • Problem is determinable • Many solutions • Predictable results • Low Risk • Slow feedback loop • Plans: Engineered or designed • C2...of these concepts in the Art of Command and the Science of Control, but lacks a proper model to assist commanders in determining how to correctly...commanders in determining how to correctly apply the concepts based on the operational environment. The paper concludes with a recommendation that the

A Systems Engineering Process for Selecting Technologies to Mitigate the Risk of Operating Rotorcraft in Degraded Visual Environments

DTIC Science & Technology

2013-09-30

combining their know-how into a mathematical framework that properly captures their intent. Leveraging this framework is the final step by which all...into quantifiable and measureable concepts. The prior phase identified the capability gaps as the highest level goals and a series of DVE mitigation...gapy and s, is the level of satisfaction of said function as mathematically defined below. Similarly, the relationship between technology and

Test Operations Procedure (TOP) 05-2-543 Enhanced Flight Termination Receiver (EFTR) Range Certification Testing

DTIC Science & Technology

2011-07-25

testing, the EFTR must be keyed with the same key used to encrypt the Enhanced Flight Termination Systems ( EFTS ) message. To ensure identical keys...required to verify the proper state. e. Procedure. (1) Pull up EFTS graphic user interface (GUI) (Figure 3). (2) Click “Receiver Power On...commanded mode steady state input currents will not exceed their specified values. TOP 05-2-543 25 July 2011 19 Figure 3. EFTS GUIa

Aeroelastic System Development Using Proper Orthogonal Decomposition and Volterra Theory

NASA Technical Reports Server (NTRS)

Lucia, David J.; Beran, Philip S.; Silva, Walter A.

2003-01-01

This research combines Volterra theory and proper orthogonal decomposition (POD) into a hybrid methodology for reduced-order modeling of aeroelastic systems. The out-come of the method is a set of linear ordinary differential equations (ODEs) describing the modal amplitudes associated with both the structural modes and the POD basis functions for the uid. For this research, the structural modes are sine waves of varying frequency, and the Volterra-POD approach is applied to the fluid dynamics equations. The structural modes are treated as forcing terms which are impulsed as part of the uid model realization. Using this approach, structural and uid operators are coupled into a single aeroelastic operator. This coupling converts a free boundary uid problem into an initial value problem, while preserving the parameter (or parameters) of interest for sensitivity analysis. The approach is applied to an elastic panel in supersonic cross ow. The hybrid Volterra-POD approach provides a low-order uid model in state-space form. The linear uid model is tightly coupled with a nonlinear panel model using an implicit integration scheme. The resulting aeroelastic model provides correct limit-cycle oscillation prediction over a wide range of panel dynamic pressure values. Time integration of the reduced-order aeroelastic model is four orders of magnitude faster than the high-order solution procedure developed for this research using traditional uid and structural solvers.

How to select a proper early warning threshold to detect infectious disease outbreaks based on the China infectious disease automated alert and response system (CIDARS).

PubMed

Wang, Ruiping; Jiang, Yonggen; Michael, Engelgau; Zhao, Genming

2017-06-12

China Centre for Diseases Control and Prevention (CDC) developed the China Infectious Disease Automated Alert and Response System (CIDARS) in 2005. The CIDARS was used to strengthen infectious disease surveillance and aid in the early warning of outbreak. The CIDARS has been integrated into the routine outbreak monitoring efforts of the CDC at all levels in China. Early warning threshold is crucial for outbreak detection in the CIDARS, but CDCs at all level are currently using thresholds recommended by the China CDC, and these recommended thresholds have recognized limitations. Our study therefore seeks to explore an operational method to select the proper early warning threshold according to the epidemic features of local infectious diseases. The data used in this study were extracted from the web-based Nationwide Notifiable Infectious Diseases Reporting Information System (NIDRIS), and data for infectious disease cases were organized by calendar week (1-52) and year (2009-2015) in Excel format; Px was calculated using a percentile-based moving window (moving window [5 week*5 year], x), where x represents one of 12 centiles (0.40, 0.45, 0.50….0.95). Outbreak signals for the 12 Px were calculated using the moving percentile method (MPM) based on data from the CIDARS. When the outbreak signals generated by the 'mean + 2SD' gold standard were in line with a Px generated outbreak signal for each week during the year of 2014, this Px was then defined as the proper threshold for the infectious disease. Finally, the performance of new selected thresholds for each infectious disease was evaluated by simulated outbreak signals based on 2015 data. Six infectious diseases were selected in this study (chickenpox, mumps, hand foot and mouth diseases (HFMD), scarlet fever, influenza and rubella). Proper thresholds for chickenpox (P75), mumps (P80), influenza (P75), rubella (P45), HFMD (P75), and scarlet fever (P80) were identified. The selected proper thresholds for these 6 infectious diseases could detect almost all simulated outbreaks within a shorter time period compared to thresholds recommended by the China CDC. It is beneficial to select the proper early warning threshold to detect infectious disease aberrations based on characteristics and epidemic features of local diseases in the CIDARS.

46 CFR 199.45 - Tests and inspections of lifesaving equipment and arrangements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... rescue boats, including engines and release mechanisms; (3) The proper condition of flotation equipment... indicating radiobeacons (EPIRB), search and rescue transponders (SART), and pyrotechnic signaling devices; (5... repeated; (2) The proper condition and operation of lifeboats and rescue boats, including engines and...

46 CFR 199.45 - Tests and inspections of lifesaving equipment and arrangements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... rescue boats, including engines and release mechanisms; (3) The proper condition of flotation equipment... indicating radiobeacons (EPIRB), search and rescue transponders (SART), and pyrotechnic signaling devices; (5... repeated; (2) The proper condition and operation of lifeboats and rescue boats, including engines and...

46 CFR 199.45 - Tests and inspections of lifesaving equipment and arrangements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... rescue boats, including engines and release mechanisms; (3) The proper condition of flotation equipment... indicating radiobeacons (EPIRB), search and rescue transponders (SART), and pyrotechnic signaling devices; (5... repeated; (2) The proper condition and operation of lifeboats and rescue boats, including engines and...

46 CFR 199.45 - Tests and inspections of lifesaving equipment and arrangements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... rescue boats, including engines and release mechanisms; (3) The proper condition of flotation equipment... indicating radiobeacons (EPIRB), search and rescue transponders (SART), and pyrotechnic signaling devices; (5... repeated; (2) The proper condition and operation of lifeboats and rescue boats, including engines and...

46 CFR 199.45 - Tests and inspections of lifesaving equipment and arrangements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... rescue boats, including engines and release mechanisms; (3) The proper condition of flotation equipment... indicating radiobeacons (EPIRB), search and rescue transponders (SART), and pyrotechnic signaling devices; (5... repeated; (2) The proper condition and operation of lifeboats and rescue boats, including engines and...

Present capabilities and future requirements for computer-aided geometric modeling in the design and manufacture of gas turbine

NASA Technical Reports Server (NTRS)

Caille, E.; Propen, M.; Hoffman, A.

1984-01-01

Gas turbine engine design requires the ability to rapidly develop complex structures which are subject to severe thermal and mechanical operating loads. As in all facets of the aerospace industry, engine designs are constantly driving towards increased performance, higher temperatures, higher speeds, and lower weight. The ability to address such requirements in a relatively short time frame has resulted in a major thrust towards integrated design/analysis/manufacturing systems. These computer driven graphics systems represent a unique challenge, with major payback opportunities if properly conceived, implemented, and applied.

Scattering General Analysis; ANALISIS GENERAL DE LA DISPERSION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tixaire, A.G.

1962-01-01

A definition of scattering states is given. It is shown that such states must belong to the absolutely continuous part of the spectrum of the total hamiltonian whenever scattering systems are considered. Such embedding may be proper unless the quantum system is physically admissible. The Moller wave operators are analyzed using Abel- and Cesaro-limit theoretical arguments. Von Neumann s ergodic theorem is partially generalized. A rigorous derivation of the Gell-Mann and Goldberger and Lippmann and Schwinger equations is obtained by making use of results on spectral theory, wave function, and eigendifferential concepts contained. (auth)

Lattice hydrodynamic model based traffic control: A transportation cyber-physical system approach

NASA Astrophysics Data System (ADS)

Liu, Hui; Sun, Dihua; Liu, Weining

2016-11-01

Lattice hydrodynamic model is a typical continuum traffic flow model, which describes the jamming transition of traffic flow properly. Previous studies in lattice hydrodynamic model have shown that the use of control method has the potential to improve traffic conditions. In this paper, a new control method is applied in lattice hydrodynamic model from a transportation cyber-physical system approach, in which only one lattice site needs to be controlled in this control scheme. The simulation verifies the feasibility and validity of this method, which can ensure the efficient and smooth operation of the traffic flow.

Infrared fiber-optic fire sensors - Concepts and designs for Space Station applications

NASA Technical Reports Server (NTRS)

Tapphorn, Ralph M.; Porter, Alan R.

1990-01-01

Various design configurations used for testing IR fiber-optic (IFO) fire-sensor concepts are presented. Responsibility measurements conducted to select the best concept are reviewed. The results indicate that IFO fire-sensor systems based on distributed fiber sensors are feasible for future aerospace applications. For Space Station Freedom, these systems offer alternative fire detectors for monitoring areas within equipment or stage compartments where the ventilation may be inadequate for proper operation of smoke detectors. They also allow a large number of areas to be monitored by a single central detector unit, which reduces the associated cost and weight.

The spurious response of microwave photonic mixer

NASA Astrophysics Data System (ADS)

Xiao, Yongchuan; Zhong, Guoshun; Qu, Pengfei; Sun, Lijun

2018-02-01

Microwave photonic mixer is a potential solution for wideband information systems due to the ultra-wide operating bandwidth, high LO-to-RF isolation, the intrinsic immunity to electromagnetic interference, and the compatibility with exsiting microwave photonic transmission systems. The spurious response of microwave photonic mixer cascading in series a pair of Mach-Zehnder interferometric intensity modulators has been simulated and analyzed in this paper. The low order spurious products caused by the nonlinearity of modulators are non-negligible, and the proper IF frequency and accurate bias-controlling are of great importance to mitigate the impact of spurious products.

Digital security technology simplified.

PubMed

Scaglione, Bernard J

2007-01-01

Digital security technology is making great strides in replacing analog and other traditional security systems including CCTV card access, personal identification and alarm monitoring applications. Like any new technology, the author says, it is important to understand its benefits and limitations before purchasing and installing, to ensure its proper operation and effectiveness. This article is a primer for security directors on how digital technology works. It provides an understanding of the key components which make up the foundation for digital security systems, focusing on three key aspects of the digital security world: the security network, IP cameras and IP recorders.

Optical monitoring of scoliosis by 3D medical laser scanner

NASA Astrophysics Data System (ADS)

Rodríguez-Quiñonez, Julio C.; Sergiyenko, Oleg Yu.; Preciado, Luis C. Basaca; Tyrsa, Vera V.; Gurko, Alexander G.; Podrygalo, Mikhail A.; Lopez, Moises Rivas; Balbuena, Daniel Hernandez

2014-03-01

Three dimensional recording of the human body surface or anatomical areas have gained importance in many medical applications. In this paper, our 3D Medical Laser Scanner is presented. It is based on the novel principle of dynamic triangulation. We analyze the method of operation, medical applications, orthopedically diseases as Scoliosis and the most common types of skin to employ the system the most proper way. It is analyzed a group of medical problems related to the application of optical scanning in optimal way. Finally, experiments are conducted to verify the performance of the proposed system and its method uncertainty.

Design, fabrication and systems integration of a satellite tracked, free-drifting ocean data buoy

NASA Technical Reports Server (NTRS)

Wallace, J. W.; Cox, J. W.

1976-01-01

Engineering details are presented of a small free-drifting buoy configuration designed for use in the study of continental shelf water circulation patterns in the Chesapeake Bight of the Western North Atlantic Ocean. The buoy incoporated French instrumentation and was interrogated by the French EOLE satellite to provide position and four channels of temperature data. The buoy design included a variable depth drogue and a power supply sufficient for six weeks of continuous operations. Proof tests of the configuration indicated an adequate design and subsequent field experiments verified the proper functioning of the system.

Metallic Thermal Protection System Technology Development: Concepts, Requirements and Assessment Overview

NASA Technical Reports Server (NTRS)

Dorsey, John T.; Poteet, Carl C.; Chen, Roger R.; Wurster, Kathryn E.

2002-01-01

A technology development program was conducted to evolve an earlier metallic thermal protection system (TPS) panel design, with the goals of: improving operations features, increasing adaptability (ease of attaching to a variety of tank shapes and structural concepts), and reducing weight. The resulting Adaptable Robust Metallic Operable Reusable (ARMOR) TPS system incorporates a high degree of design flexibility (allowing weight and operability to be traded and balanced) and can also be easily integrated with a large variety of tank shapes, airframe structural arrangements and airframe structure/material concepts. An initial attempt has been made to establish a set of performance based TPS design requirements. A set of general (FARtype) requirements have been proposed, focusing on defining categories that must be included for a comprehensive design. Load cases required for TPS design must reflect the full flight envelope, including a comprehensive set of limit loads, However, including additional loads. such as ascent abort trajectories, as ultimate load cases, and on-orbit debris/micro-meteoroid hypervelocity impact, as one of the discrete -source -damage load cases, will have a significant impact on system design and resulting performance, reliability and operability. Although these load cases have not been established, they are of paramount importance for reusable vehicles, and until properly included, all sizing results and assessments of reliability and operability must be considered optimistic at a minimum.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clausing, R.E.

Equations based on kinetic theory relate the contamination of refractory metals in vacuum to the appropriate variables. Several examples are given for which the allowable system pressures are calculated. The examples illustrate the effect of varying several parameters. The importance of the sticking factor for active gases on hot refractory metals and its effect on the system design are discussed. The data for estimating the sticking factor for O/sub 2/ on Nb are given, along with some estimated values. Experimental data on the composition and rates of outgassing of ultrahigh-vacuum systems and their importance in system design are discussed. Severalmore » methods of reducing contamination rates and the relative ease and effectiveness of these methods are presented. It was concluded that tests of 1000 hr or longer will probably require system pressures of between 10/sup -9/ and 10/sup -6/ torr, the particular pressure depending upon the residual gas composition, test duration, allowable contamination level, and the other variables discussed. Since the most important source of contamination in a properly designed ultrahigh-vacuum system is the outgassing process, bakeable systems should be designed to operate with walls as cool as practical, and to have a minimum of surface area and outgassing materials inside. Considerable added protection may be obtained by incorporating sacrificial getter surfaces in the system, or, alternatively, higher pressures may be tolerated if proper getter design is used. (auth)« less

Development of a measurement and control system for a 10 kW@20 K refrigerator based on Siemens PLC S7-300

NASA Astrophysics Data System (ADS)

Li, J.; Liu, L. Q.; Liu, T.; Xu, X. D.; Dong, B.; Lu, W. H.; Pan, W.; Wu, J. H.; Xiong, L. Y.

2017-02-01

A 10 kW@20 K refrigerator has been established by the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. A measurement and control system based on Siemens PLC S7-300 for this 10 kW@20 K refrigerator is developed. According to the detailed measurement requirements, proper sensors and transmitters are adopted. Siemens S7-300 PLC CPU315-2 PN/DP operates as a master station. Two sets of ET200M DP remote expand I/O, one power meter, two compressors and one vacuum gauge operate as slave stations. Profibus-DP field communication and Modbus communication are used between the master station and the slave stations in this control system. The upper computer HMI (Human Machine Interface) is compiled using Siemens configuration software WinCC V7.0. The upper computer communicates with PLC by means of industrial Ethernet. After commissioning, this refrigerator has been operating with a 10 kW of cooling power at 20 K for more than 72 hours.

The Influence of Modulated Signal Risetime in Flight Electronics Radiated Immunity Testing with a Mode-Stirred Chamber

NASA Technical Reports Server (NTRS)

Ely, Jay J.; Nguyen, Truong X.; Scearce, Stephen A.

2000-01-01

For electromagnetic immunity testing of an electronic system, it is desirable to demonstrate its functional integrity when exposed to the full range and intensity of environmental electromagnetic threats that may be encountered over its operational life. As part of this, it is necessary to show proper system operation when exposed to representative threat signal modulations. Modulated signal transition time is easily overlooked, but can be highly significant to system susceptibility. Radiated electromagnetic field immunity testing is increasingly being performed in Mode Stirred Chambers. Because the peak field vs. time relationship is affected by the operation of a reverberating room, it is important to understand how the room may influence any input signal modulation characteristics. This paper will provide insight into the field intensity vs. time relationship within the test environment of a mode stirred chamber. An understanding of this relationship is important to EMC engineers in determining what input signal modulation characteristics will be transferred to the equipment under test. References will be given for the development of this topic, and experimental data will be presented

Long term remediation of highly polluted acid mine drainage: a sustainable approach to restore the environmental quality of the Odiel river basin.

PubMed

Caraballo, Manuel A; Macías, Francisco; Rötting, Tobias S; Nieto, José Miguel; Ayora, Carlos

2011-12-01

During 20 months of proper operation the full scale passive treatment in Mina Esperanza (SW Spain) produced around 100 mg/L of ferric iron in the aeration cascades, removing an average net acidity up to 1500 mg/L as CaCO(3) and not having any significant clogging problem. Complete Al, As, Cd, Cr, Cu, Ti and V removal from the water was accomplished through almost the entire operation time while Fe removal ranged between 170 and 620 mg/L. The system operated at a mean inflow rate of 43 m(3)/day achieving an acid load reduction of 597 g·(m(2) day)(-1), more than 10 times higher than the generally accepted 40 g·(m(2) day)(-1) value commonly used as a passive treatment system designing criteria. The high performance achieved by the passive treatment system at Mina Esperanza demonstrates that this innovative treatment design is a simple, efficient and long lasting remediation option to treat highly polluted acid mine drainage. Copyright © 2011 Elsevier Ltd. All rights reserved.

Prototype Development of Remote Operated Hot Uniaxial Press (ROHUP) to Fabricate Advanced Tc-99 Bearing Ceramic Waste Forms - 13381

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alaniz, Ariana J.; Delgado, Luc R.; Werbick, Brett M.

The objective of this senior student project is to design and build a prototype construction of a machine that simultaneously provides the proper pressure and temperature parameters to sinter ceramic powders in-situ to create pellets of rather high densities of above 90% (theoretical). This ROHUP (Remote Operated Hot Uniaxial Press) device is designed specifically to fabricate advanced ceramic Tc-99 bearing waste forms and therefore radiological barriers have been included in the system. The HUP features electronic control and feedback systems to set and monitor pressure, load, and temperature parameters. This device operates wirelessly via portable computer using Bluetooth{sup R} technology.more » The HUP device is designed to fit in a standard atmosphere controlled glove box to further allow sintering under inert conditions (e.g. under Ar, He, N{sub 2}). This will further allow utilizing this HUP for other potential applications, including radioactive samples, novel ceramic waste forms, advanced oxide fuels, air-sensitive samples, metallic systems, advanced powder metallurgy, diffusion experiments and more. (authors)« less

A Potentially Useful for Airborne Separation in 4D-Trajectory ATM Operations

NASA Technical Reports Server (NTRS)

Wing, David J.

2005-01-01

An aircraft equipped with Airborne Separation Assistance System functions and 4- dimensional trajectory management capabilities can have significant, potentially transforming, value to Air Traffic Management at the local and system levels. This paper discusses how certain vital characteristics envisioned in the Next Generation Air Transportation System enable some Air Traffic Management functions to be distributed to properly equipped aircraft, and it defines and illustrates this equipage level in a potential application. The new equipage level, perhaps the most capable of many levels permitted, enables an effective implementation of both near- and long-term 4-dimensional trajectory operations in complex airspace, with the aircraft providing the near-term tactical functions and conforming to the long-term trajectory attributes coordinated with ground-based Traffic Flow Management authorities. NASA s recent research and development of this proposed aircraft equipage for en-route and terminal-arrival operations is summarized. The role the equipage level may play in addressing key implementation challenges of reducing ground infrastructure cost, building in security and safety, and scaling to traffic demand is discussed.

Water-absorbing capacitor system for measuring relative humidity

NASA Technical Reports Server (NTRS)

Laue, Eric G. (Inventor)

1987-01-01

A method and apparatus using a known water-absorbent polymer as a capacitor which is operated at a dc voltage for measuring relative humidity is presented. When formed as a layer between porous electrically-conductive electrodes and operated in an RC oscillator circuit, the oscillator frequency varies inversely with the partial pressure of the moisture to be measured. In a preferred embodiment, the capacitor is formed from Nafion and is operated at a low dc voltage with a resistor as an RC circuit in an RC oscillator. At the low voltage, the leakage current is proper for oscillation over a satisfactory range. The frequency of oscillation varies in an essentially linear fashion with relative humidity which is represented by the moisture being absorbed into the Nafion. The oscillation frequency is detected by a frequency detector.

40 CFR 60.2635 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) Environmental concerns, including types of emissions. (ii) Basic combustion principles, including products of combustion. (iii) Operation of the specific type of incinerator to be used by the operator, including proper startup, waste charging, and shutdown procedures. (iv) Combustion controls and monitoring. (v) Operation...

40 CFR 60.2070 - What are the operator training and qualification requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) Environmental concerns, including types of emissions. (ii) Basic combustion principles, including products of combustion. (iii) Operation of the specific type of incinerator to be used by the operator, including proper startup, waste charging, and shutdown procedures. (iv) Combustion controls and monitoring. (v) Operation...

46 CFR 177.1030 - Operating station visibility.

Code of Federal Regulations, 2010 CFR

2010-10-01

... TONS) CONSTRUCTION AND ARRANGEMENT Window Construction and Visibility § 177.1030 Operating station visibility. (a) Windows and other openings at the operating station must be of sufficient size and properly... glazing material used in windows at the operating station must have a light transmission of not less than...

Flight elements: Advanced avionics systems architectures

NASA Technical Reports Server (NTRS)

1990-01-01

Space transportation objectives are associated with transporting material from Earth to orbit, interplanetary travel, and planetary landing. The objectives considered herein are associated with Earth to orbit transportation. Many good avionics architectural features will support all phases of space transportation, but interplanetary transportation poses significantly different problems such as long mission time with high reliability, unattended operation, and many different opportunities such as long nonoperational flight segments that can be used for equipment fault diagnosis and repair. Fault tolerance can be used to permit continued operation with faulty units, not only during launch but also, and perhaps with more impact, during prelaunch activities. Avionics systems are entering a phase of development where the traditional approaches to satisfactory systems based on engineering judgement and thorough testing will alone no longer be adequate to assure that the required system performance can be obtained. A deeper understanding will be required to make the effects of obscure design decisions clear at a level where their impact can be properly judged.

Demonstration of a full-scale plant using an UASB followed by a ceramic MBR for the reclamation of industrial wastewater.

PubMed

Niwa, Terutake; Hatamoto, Masashi; Yamashita, Takuya; Noguchi, Hiroshi; Takase, Osamu; Kekre, Kiran A; Ang, Wui Seng; Tao, Guihe; Seah, Harry; Yamaguchi, Takashi

2016-10-01

This study comprehensively evaluated the performance of a full-scale plant (4550m(3)d(-1)) using a UASB reactor followed by a ceramic MBR for the reclamation and reuse of mixed industrial wastewater containing many inorganics, chemical, oil and greases. This plant was demonstrated as the first full-scale system to reclaim the mixed industrial wastewater in the world. During 395days of operation, influent chemical oxygen demand (COD) fluctuated widely, but this system achieved COD removal rate of 91% and the ceramic MBR have operated flux of 21-25LMH stably. This means that this system adsorbed the feed water fluctuation and properly treated the water. Energy consumption of this plant was achieved 0.76kWhmm(-3) and this value is same range of domestic sewage MBR system. The combination of an UASB reactor and ceramic MBR is the most economical and feasible solution for water reclamation of mixed industrial wastewater. Copyright © 2016 Elsevier Ltd. All rights reserved.

A Method for Optimal Load Dispatch of a Multi-zone Power System with Zonal Exchange Constraints

NASA Astrophysics Data System (ADS)

Hazarika, Durlav; Das, Ranjay

2018-04-01

This paper presented a method for economic generation scheduling of a multi-zone power system having inter zonal operational constraints. For this purpose, the generator rescheduling for a multi area power system having inter zonal operational constraints has been represented as a two step optimal generation scheduling problem. At first, the optimal generation scheduling has been carried out for the zone having surplus or deficient generation with proper spinning reserve using co-ordination equation. The power exchange required for the deficit zones and zones having no generation are estimated based on load demand and generation for the zone. The incremental transmission loss formulas for the transmission lines participating in the power transfer process among the zones are formulated. Using these, incremental transmission loss expression in co-ordination equation, the optimal generation scheduling for the zonal exchange has been determined. Simulation is carried out on IEEE 118 bus test system to examine the applicability and validity of the method.

[The endoscopic operating room OR 1].

PubMed

Dubuisson, J B; Chapron, C

2003-04-01

During the last few years, the development of surgical laparoscopy has been the major turning point, and the most important progress in the field of surgery. The specific installation requirements of surgical laparoscopy, as well as the technological progress proper to this surgical technique, justify the need of a new organization of the operating theatre. The new operating room OR 1 is especially designed to fit and satisfy the requirements of a modern operating theatre, where surgical laparoscopy plays a major role. The organization and the design of this new operating room (OR 1) rely on 2 main concepts: architectural, and computerized, through 2 PC systems SCB and AIDA. The main objectives of this new concept are: allowing the surgeon to control and command all the functions and the instruments, as well as the lighting of the room and the operating field; managing the surgical data and images required for medical files; establishing a communication network either from the inside or outside the sterile zone.